Geohydrologic aspects for siting and design of low-level radioactive-waste disposal

Science.gov (United States)

Bedinger, M.S.

1989-01-01

The objective for siting and design of low-level radioactive-waste repository sites is to isolate the waste from the biosphere until the waste no longer poses an unacceptable hazard as a result of radioactive decay. Low-level radioactive waste commonly is isolated at shallow depths with various engineered features to stabilize the waste and to reduce its dissolution and transport by ground water. The unsaturated zone generally is preferred for isolating the waste. Low-level radioactive waste may need to be isolated for 300 to 500 years. Maintenance and monitoring of the repository site are required by Federal regulations for only the first 100 years. Therefore, geohydrology of the repository site needs to provide natural isolation of the waste for the hazardous period following maintenance of the site. Engineering design of the repository needs to be compatible with the natural geohydrologic conditions at the site. Studies at existing commercial and Federal waste-disposal sites provide information on the problems encountered and the basis for establishing siting guidelines for improved isolation of radioactive waste, engineering design of repository structures, and surveillance needs to assess the effectiveness of the repositories and to provide early warning of problems that may require remedial action.Climate directly affects the hydrology of a site and probably is the most important single factor that affects the suitability of a site for shallow-land burial of low-level radioactive waste. Humid and subhumid regions are not well suited for shallow isolation of low-level radioactive waste in the unsaturated zone; arid regions with zero to small infiltration from precipitation, great depths to the water table, and long flow paths to natural discharge areas are naturally well suited to isolation of the waste. The unsaturated zone is preferred for isolation of low-level radioactive waste. The guiding rationale is to minimize contact of water with the waste and to

Parametric study of geohydrologic performance characteristics for geologic waste repositories

International Nuclear Information System (INIS)

Bailey, C.E.; Marine, I.W.

1980-11-01

One of the major objectives of the National Waste Terminal Storage Program is to identify potential geologic sites for storage and isolation of radioactive waste (and possibly irradiated fuel). Potential sites for the storage and isolation of radioactive waste or spent fuel in a geologic rock unit are being carefully evaluated to ensure that radionuclides from the stored waste or fuel will never appear in the biosphere in amounts that would constitute a hazard to the health and safety of the public. The objective of this report is to quantify and present in graphical form the effects of significant geohydrologic and other performance characteristics that would influence the movement of radionuclides from a storage site in a rock unit to the biosphere. The effort in this study was focused on transport by groundwater because that is the most likely method of radionuclide escape. Graphs of the major performance characteristics that influence the transport of radionuclides from a repository to the biosphere by groundwater are presented. The major characteristics addressed are radioactive decay, leach rate, hydraulic conductivity, porosity, groundwater gradient, hydrodynamic dispersion, ion exchange, and distance to the biosphere. These major performance characteristics are combind with each other and with the results of certain other combinations and presented in graphical form to provide the interrelationships of values measured during field studies. The graphical form of presentation should be useful in the screening process of site selection. An appendix illustrates the use of these graphs to assess the suitability of a site

Geohydrological and environmental isotope observation of Sishen ground waters

International Nuclear Information System (INIS)

Verhagen, B.Th.; Dziembowski, Z.M.

1985-01-01

The dewatering of Sishen Mine in the northern Cape Province supplies good quality water for the mine and surrounding areas. Using various approaches, attempts are made to quantify the remaining storage of ground water. Geohydrological observations provide an estimate based on extrapolating the thickness of dewatered rock. Environmental isotope observations on various borehole outputs show contrasts between different ground-water bodies and their mixtures and allows for some extrapolations of observed trends. Indications are that previous estimates of storage, based on ground-water level changes, are conservative

Effective summary evaluators for deep nuclear waste repositories: geohydrologic response function

International Nuclear Information System (INIS)

Nelson, R.W.; Dove, F.H.

1981-03-01

Useful insight has been gained over the past four years as hydrologic system modeling has been applied to evaluate hypothetical, waste-repository sites in various geologic media. The Geohydrologic Response Functions, described in this paper, are shown to: blend extensive results of technical analysis into simple summary relationships, and to potentially help the public and decision makers to evaluate the magnitude of any loss in repository integrity

Geohydrology of the Gallup's Quarry area, Plainfield, Connecticut

Science.gov (United States)

Melvin, Robert L.; Stone, Janet Radway; Craft, Patrick A.; Lane, John W.

1995-01-01

recharge based on regional analyses for 1978-91 are 30 inches in areas where stratified drift are exposed and 9.6 inches in areas where till and crystalline bedrock are exposed. The hydraulic conductivity of the coarse-grained stratified drift, identified in earlier U.S. Geological Survey studies as part of an aquifer capable of yielding large quantities of water, may be several hundred feet per day. The hydraulic conductivity of the till, based on regional information, is likely 0.04 to 24 feet per day. More detailed geohydrologic information is required to develop effective remedial programs at Gallup's Quarry, particularly in the areas north and west of the waste-disposal areas. Detailed subsurface geologic mapping and definition of head distribution and other hydraulic properties of each geohydrologic unit would indicate directions and rates of ground-water flow. Most importantly, the present extent of contamination of water and sediments throughout the area will have to be determined.

Geohydrological investigation of an uranium anomaly near Vanzylsrus in the Northern Cape Province

International Nuclear Information System (INIS)

Levin, M.; Talma, A.S.; Vogel, J.C.

1982-01-01

An anomaly, caused by low-grade uranium accumulations in organic-rich diatomaceous earth deposits, was located by an airborne radiometric survey near Vanzylsrus in the Northern Cape. Low-grade uraniferous calcrete also occurs in the vicinity of the anomaly. A significant uranium anomaly was found along the whole course of the palaeodrainage with the highest values occuring behind a dolerite dyke a few kilometres south of the confluence. A multidisciplinary approach in corporating geohydrology, water geochemistry, isotopic data and radiometric borehole logging studies was used to evaluate its potential

Hydrological, meteorological and geohydrological data for an unsaturated zone study near the Radioactive Waste Management Complex, Idaho National Engineering Laboratory, Idaho - 1987

International Nuclear Information System (INIS)

Davis, L.C.; Pittman, J.R.

1990-01-01

Since 1952, radioactive waste has been buried at the RWMC (Radioactive Waste Management Complex) at the Idaho National Engineering Laboratory in southeastern Idaho. In 1985, the US Geological Survey, in cooperation with the US Department of Energy, began a study of the geohydrology of the RWMC to provide a basis for estimating the extent of and the potential for migration of radionuclides in the unsaturated zone beneath the waste burial trenches and pits. This study is being conducted to provide hydrological, meteorological and geohydrological data for the test trench area adjacent to the northern boundary of the RWMC. During 1987, data were collected from the test trench area, where several types of instrumentation were installed in the surficial sediment in 1985. Hydrological data collected from both disturbed and undisturbed soil included measurements, from 28 thermocouple psychrometers placed at selected depths to about 6m. Soil moisture content measurements were collected bi-weekly in 9 neutron-probe access holes with a neutron moisture depth gage. Meteorological data summarized daily included: (1) incoming and emitted long-wave radiation; (2) incoming and reflected short-wave radiation; (3) air temperature; (4) relative humidity; (5) wind speed; (6) wind direction; and (7) precipitation. To describe grain-size distribution with depth, 17 samples were analyzed using sieve and pipette methods. Statistical parameters, carbonate content, color, particle roundness and sphericity, and mineralogic and clastic constituents were determined for each sample. Some samples were analyzed by x-ray diffraction techniques to determine bulk and clay mineralogy

Geohydrology of the Cerro Prieto geothermal aquifer

Energy Technology Data Exchange (ETDEWEB)

Sanchez R, J.; de la Pena L, A.

1981-01-01

The most recent information on the Cerro Prieto geothermal aquifer is summarized, with special emphasis on the initial production zone where the wells completed in the Alpha aquifer are located. These wells produce steam for power plant units 1 and 2. Brief comments also are made on the Beta aquifer, which underlies the Alpha aquifer in the Cerro Prieto I area and which extends to the east to what is known as the Cerro Prieto II and Cerro Prieto III areas. The location of the area studied is shown. The Alpha and Beta aquifers differ in their mineralogy and cementing mineral composition, temperatures, and piezometric levels. The difference in piezometric levels indicates that there is no local communication between the two aquifers. This situation has been verified by a well interference test, using well E-1 as a producer in the Beta aquifer and well M-46 as the observation well in the Alpha aquifer. No interference between them was observed. Information on the geology, geohydrology, and geochemistry of Cerro Prieto is presented.

Preliminary three-dimensional geohydrologic framework of the San Antonio Creek Groundwater Basin, Santa Barbara County, California

Science.gov (United States)

Cromwell, G.; Sweetkind, D. S.; O'leary, D. R.

2017-12-01

The San Antonio Creek Groundwater Basin is a rural agricultural area that is heavily dependent on groundwater to meet local water demands. The U.S. Geological Survey (USGS) is working cooperatively with Santa Barbara County and Vandenberg Air Force Base to assess the quantity and quality of the groundwater resources within the basin. As part of this assessment, an integrated hydrologic model that will help stakeholders to effectively manage the water resources in the basin is being developed. The integrated hydrologic model includes a conceptual model of the subsurface geology consisting of stratigraphy and variations in lithology throughout the basin. The San Antonio Creek Groundwater Basin is a relatively narrow, east-west oriented valley that is structurally controlled by an eastward-plunging syncline. Basin-fill material beneath the valley floor consists of relatively coarse-grained, permeable, marine and non-marine sedimentary deposits, which are underlain by fine-grained, low-permeability, marine sedimentary rocks. To characterize the system, surficial and subsurface geohydrologic data were compiled from geologic maps, existing regional geologic models, and lithology and geophysical logs from boreholes, including two USGS multiple-well sites drilled as part of this study. Geohydrologic unit picks and lithologic variations are incorporated into a three-dimensional framework model of the basin. This basin (model) includes six geohydrologic units that follow the structure and stratigraphy of the area: 1) Bedrock - low-permeability marine sedimentary rocks; 2) Careaga Formation - fine to coarse grained near-shore sandstone; 3) Paso Robles Formation, lower portion - sandy-gravely deposits with clay and limestone; 4) Paso Robles Formation, middle portion - clayey-silty deposits; 5) Paso Robles Formation, upper portion - sandy-gravely deposits; and 6) recent Quaternary deposits. Hydrologic data show that the upper and lower portions of the Paso Robles Formation are

Geohydrology and potential effects of coal mining in 12 coal-lease areas, Powder River structural basin, northeastern Wyoming. Water Resources Investigation

International Nuclear Information System (INIS)

Fogg, J.L.; Martin, M.W.; Daddow, P.B.

1991-01-01

The purpose of the report is to describe the geohydrology of 12 coal-lease areas in the Powder River structural basin in relation to the mining proposed for each area. The description of the geohydrology of each of the lease areas focuses on the shallow ground-water system and includes identification of recharge and discharge areas, directions of ground-water movement, and potential effects of mining. The shallow ground-water system in the Powder River structural basin is not well defined because of the discontinuous nature of the aquifers in the basin. Understanding the ground-water hydrology of these 12 coal-lease areas will improve understanding of the shallow ground-water system in the basin. The first part of the report is a description of the general geohydrology of the Wyoming part of the Powder River structural basin. The second part of the report is a general discussion of the effects of coal mining on ground-water hydrology. The third part of the report contains site-specific discussions of the ground-water hydrology and potential effects of mining for each of the 12 coal-lease areas

Geohydrology of the valley-fill aquifer in the Corning area, Steuben County, New York

Science.gov (United States)

Miller, Todd S.; Belli, J.L.; Allen, R.V.

1982-01-01

This report is the seventh in a series of 11 map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on six maps at 1:24,000 scale. Together, the maps provide a comprehensive overview of a major valley-fill aquifer in southeastern Steuben County. The maps include surficial geology, geologic sections, water-infiltration potential of soil zone, aquifer thickness, potentiometric-surface elevations, and land use. The valley-fill deposits consist of alluvial silt, sand, and gravel, glacial-outwash (sand and gravel), till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities, whereas the till and silt deposits have relatively low permeabilities. Water-table conditions prevail in unconfined sand and gravel along the valley margin. Artesian conditions are found locally in sand and gravel confined under silt and clay in the middle of the valley. Recharge occurs nearly everywhere on the valley floor, but principally along the margin of the valley, where highly permeable land surface conditions exist, and runoff from the hillsides is concentrated. The use of land overlying the aquifer is a mixture of residential, commercial, agricultural, and industrial uses. (USGS)

Geohydrology of the valley-fill aquifer in the Jamestown area, Chautauqua County, New York

Science.gov (United States)

Anderson, H.R.; Stelz, W.G.; Belli, J.L.; Allen, R.V.

1982-01-01

This report is the sixth in a series of 11 map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on six maps at 1:24,000 scale. Together, the maps provide a comprehensive overview of a major valley-fill aquifer in southeastern Chautauqua County. The maps include surficial geology, geologic sections, water-infiltration potential of soil zone, aquifer thickness, potentiometric-surface elevations and land use. The valley-fill deposits consist of alluvial silt and sand, glacial-outwash (sand and gravel), ice-contact sand and gravel, till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities whereas the till, silt and clay deposits have relatively low permeabilities. Water-table conditions prevail in u nconfined sand and gravel beds along the valley margin. Artesian conditions prevail in confined sand and gravel buried under silt and clay in the middle of the valley. Recharge occurs mainly along the margin of the valley, where the land surface is highly permeable and runoff from the hillsides is concentrated. The use of land overlying the aquifer is predominantly agricultural and residential with lesser amounts of commercial and industrial uses. (USGS)

Geohydrological considerations in land disposal of LLW

International Nuclear Information System (INIS)

Yeh, G.T.; Tamura, T.

1981-01-01

The geohydrological and geochemical factors that affect the transport, transfer, and transformation of the waste in the aquifer system as a result of shallow land burial practices are discussed. They include surface topography and its character, the extent of the aquifer, nearby surface water bodies, groundwater basin divide, watershed boundaries, rainfall rate, infiltration from surface water bodies, potential evapotranspiration, hydraulic conductivity, water capacity, porosity, compressibility of the matrix, dispersivity, hydrolysis, photolysis, oxidation, volatilization, biolysis, precipitation, mineral comosition, and flow dynamics. Depending on the availability of data and the detail of information desired, three levels of analyses may be undertaken. Two examples are used to illustrate these three levels of analyses using hypothetical parameters. The examples are constructed to represent the leaching from wet water body and shallow burials, respectively. The former typifies a class of problems of groundwater contamination from coal-catching basins and uranium mill tailings. The latter represents classical examples of shallow land burials such as coal solid wastes, chemical dumping and sanitary landfill

Feasibility study

International Nuclear Information System (INIS)

Gibbs, P.; Kalas, P.

1975-01-01

The feasibility study itself examines the technical, economic and financial implications of a nuclear power station in depth so as to make sure that nuclear power is the right course to take. This means that it is quite an expensive operation and it is to avoid wasting this money that a pre-feasibility study is carried out. This preliminary study should eliminate cases where the electrical system cannot absorb the capacity of a nuclear station of commercial size, where other sources of power such as hydro-electricity, gas or cheap coal would make nuclear obviously uneconomic or where no suitable sites exist. If this first rather simple survey shows that nuclear power is a credible solution to a utilities need for electricity or heat production plant, then the next stage is a full feasibility study. (orig./TK) [de

Geo-hydrological hazard and urban development in the Mediterranean area: an example from Genoa City (Italy)

Science.gov (United States)

Faccini, F.; Luino, F.; Sacchini, A.; Turconi, L.; De Graff, J. V.

2015-04-01

The Ligurian area has always suffered from significant geo-hydrological events causing casualties and serious damage. The atmospheric circulation in autumn and winter coupled with landform peculiarities are the main causes this hazard becoming a risk to human life, structures, and infrastructures. Genoa city and the surrounding metropolitan area are commonly subject to heavy rainfall that induces violent flash floods and many shallow landslides. The most recent rainfall events occurred on 9-10 October and 15 November 2014, again causing loss of human lives and widespread damage. A troubling trend since the beginning of the new century, is the recurrence of such events with greater frequency than in the past. The city of Genoa serves as a very interesting case-study for geo-hydrological risks. Cloudbursts of few hours seem to have a rainfall intensity basically greater than in the past; that causes increase of hydrometric levels of the watercourses that quickly reach alarming values close to the overflowing. This meteorological factor, added to growing urbanization of the valley floors and slopes located north of Genoa, has inevitably produced a general trend of increasing risk for the city. Urbanization is particularly notable for the narrowing process in all cross-sections of Genoa's watercourses, both in the main ones and in the secondary streams that flow directly into the Gulf of Genoa. The narrowing of the sections resulted from the increasing demand for new spaces owing to both industrial development (which started initially at the coastal areas of Genoa), and the growth of the Genoa population. The number of inhabitants grew from fewer than 200 000 at the beginning of the 19th century tool a peak of over 800 000 in the 1970s modifying the water balance of the basins and increasing the geo-hydrological risk in an unacceptable way. Among the important topics analyzed in this paper are: (i) the meteorological characteristics of these events, (ii) the changes in

Geohydrological simulation of a deep coastal repository

International Nuclear Information System (INIS)

Follin, S.

1995-12-01

This conceptual-numerical study treats the dewatering and resaturation phases associated with the construction, use and closure of a coastal nuclear waste repository located at depth in sparsely fractured Baltic Shield rocks. The main objective is to simulate the extent and duration of saline intrusion for a reasonable set of geohydrological assumptions. Long-term changes in the chemical environment associated with saline intrusion may affect the properties of the buffer zone material (bentonite). The first part of the study deals with history matching of a simple model geometry and the second part treats the dewatering and resaturation phases of the simulated repository. The history matching supports the standpoint that the occurrence of saline ground water reflects an ongoing but incomplete Holocene flushing of the Baltic Shield. The drawdown after fifty years of dewatering is highly dependent on the permeability of the excavated damaged zone. If the permeability close the repository is unaltered the entire region between the top side of the model and the repository is more or less partially saturated at the end of the simulation period. The simulations of a fifty year long recovery period suggest that the distribution between fresh and saline ground waters may be quite close to the conditions prior to the dewatering phase already after fifty years of closure despite an incomplete pressure recovery, which is an interesting result considering the objective of the study. 12 refs

Preclosure monitoring and performance confirmation at Yucca Mountain: Applicability of geophysical, geohydrological, and geochemical methods

International Nuclear Information System (INIS)

Tsang, C.F.

1989-06-01

The present paper presents considerations on studies that would be required for preclosure monitoring and performance confirmation of a nuclear waste geologic repository in an unsaturated zone. The critical parameters that should be monitored are reviewed and two scales of measurement relevant to monitoring activities, room scale and repository scale, are taken as a framework for investigation. A number of monitoring methods based on geophysics, geohydrology, and geochemistry are briefly summarized for their potential usefulness for preclosure monitoring and performance confirmation of the geologic repository. Particular emphasis is given to measurement of the spatial distribution of parameters in contrast to single-point measurements of quantities. 12 refs., 1 fig., 1 tab

Geohydrology of the valley-fill aquifer in the Endicott-Johnson City area, Broome County, New York

Science.gov (United States)

Holecek, Thomas J.; Randall, A.D.; Belli, J.L.; Allen, R.V.

1982-01-01

This report is the tenth in a series of 11 map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on five maps at 1:24,000 scale. Together, the maps provide a comprehensive overview of a major valley-fill aquifer in southwestern Broome County. The maps include surficial geology, geologic sections, aquifer thickness, water-infiltration potential of soil zone, potentiometric-surface altitude, and land use. The valley-fill deposits consist of alluvial silt and sand, glacial outwash (sand and gravel), ice-contact sand and gravel, till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities whereas the till, silt, and clay deposits have relatively low permeabilities. Water-table conditions are found in unconfined sand and gravel, whereas artesian conditions prevail within sand and gravel confined by silty deposits. Recharge occurs over the entire surface of the aquifer, due to permeable land-surface conditions, but is greatest along the margin of the valley, where runoff from the hillsides is concentrated, and near streams. The use of land overlying the aquifer is predominantly commercial and residential with lesser amounts of agricultural and industrial uses. (USGS)

Geohydrology of the valley-fill aquifer in the South Fallsburgh-Woodbourne area, Sullivan County, New York

Science.gov (United States)

Anderson, H.R.; Dineen, R.J.; Stelz, W.G.; Belli, J.L.

1982-01-01

This report is the ninth in a series of map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on six maps at 1:24,000 scale. Together the maps provide a comprehensive overview of a major valley-fill aquifer in southeastern Sullivan County. The maps include surficial geology, geologic sections, aquifer thickness, water-infiltration potential of soil zone, potentiometric surface elevations, well yields, and land use. The valley-fill deposits consist of alluvial silt and sand, glacial outwash (sand and gravel), ice-contact sand and gravel, till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities whereas the till, silt, and clay deposits have relatively low permeabilities. Water-table conditions prevail in unconfined sand and gravel whereas artesian conditions prevail within sand and gravel confined by silty deposits. The aquifer is recharged throughout, where the land surface is most permeable and is greatest along the margin of the valley, where runoff from the hillsides is concentrated. The use of land overlying the aquifer is predominantly commercial, agricultural, and residential with lesser industrial uses. (USGS)

Dynamic taxonomies applied to a web-based relational database for geo-hydrological risk mitigation

Science.gov (United States)

Sacco, G. M.; Nigrelli, G.; Bosio, A.; Chiarle, M.; Luino, F.

2012-02-01

In its 40 years of activity, the Research Institute for Geo-hydrological Protection of the Italian National Research Council has amassed a vast and varied collection of historical documentation on landslides, muddy-debris flows, and floods in northern Italy from 1600 to the present. Since 2008, the archive resources have been maintained through a relational database management system. The database is used for routine study and research purposes as well as for providing support during geo-hydrological emergencies, when data need to be quickly and accurately retrieved. Retrieval speed and accuracy are the main objectives of an implementation based on a dynamic taxonomies model. Dynamic taxonomies are a general knowledge management model for configuring complex, heterogeneous information bases that support exploratory searching. At each stage of the process, the user can explore or browse the database in a guided yet unconstrained way by selecting the alternatives suggested for further refining the search. Dynamic taxonomies have been successfully applied to such diverse and apparently unrelated domains as e-commerce and medical diagnosis. Here, we describe the application of dynamic taxonomies to our database and compare it to traditional relational database query methods. The dynamic taxonomy interface, essentially a point-and-click interface, is considerably faster and less error-prone than traditional form-based query interfaces that require the user to remember and type in the "right" search keywords. Finally, dynamic taxonomy users have confirmed that one of the principal benefits of this approach is the confidence of having considered all the relevant information. Dynamic taxonomies and relational databases work in synergy to provide fast and precise searching: one of the most important factors in timely response to emergencies.

Feasibility studies and technological innovation

DEFF Research Database (Denmark)

Hvelplund, Frede Kloster; Lund, Henrik; Sukkumnoed, Decharut

2004-01-01

The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives.......The chapter offers a tool to conduct feasibility studies and focuses on how to make feasibility studies in a situation with environmental concerns, in which technological innovation and institutional chnages are among the objectives....

Geohydrology of the climax stock granite and surrounding rock formations, NTS

International Nuclear Information System (INIS)

Murray, W.A.

1981-05-01

The location of the water table and the degree of saturation of the granitic rocks in the Climax stock are presently unknown. Based on existing knowledge and an extrapolation of available geohydrologic data, it appears that the water table may lie at about 1100 to 1200 m above mean sea level (MSL) in the northeastern part of the stock and at about 800 to 900 m in the southwest. A drilling program would be required to establish these levels precisely. The degree of saturation at a given underground elevation may be approximated by a detailed inventory of seeps at that level. More precise determination of degree of saturation will require a water budet. 27 figures, 2 tables

Geohydrology of the valley-fill aquifer in the Ramapo and Mahwah rivers area, Rockland County, New York

Science.gov (United States)

Moore, Richard Bridge; Cadwell, D.H.; Stelz, W.G.; Belli, J.L.

1982-01-01

This report is the eighth in a series of 11 map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on six maps at 1:24,000 scale. Together, the maps provide a comprehensive overview of a major valley-fill aquifer in southeastern Rockland County. The maps include surficial geology, geologic sections, water-infiltration potential of soil zone, aquifer thickness, water-table elevations, well yields, and land use. The valley-fill deposits consists of alluvial silt and sand, glacial outwash (sand and gravel), ice-contact sand and gravel, till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities, whereas the till, silt, and clay deposits have relatively low permeabilities. Water-table conditions prevail in unconfined sand and gravel along the Ramapo River valley and much of the Mahwah River valley. Artesian conditions prevail in confined sand and gravel buried under silt and clay and till in parts of the Mahway valley. The aquifer is recharged throughout, where the land surface is most permeable and is greatest along the margin of the valley, where runoff from the hillsides is concentrated. The use of land overlying the aquifer is predominantly commercial, agricultural and residential, with lesser industrial uses. (USGS)

Field investigation of mining-induced seismicity on local geohydrology

International Nuclear Information System (INIS)

Hsiung, S.M.; Chowdhury, A.H.; Philip, J.; Blake, W.

1993-01-01

Hydraulic response of the rock mass due to earthquakes is one of the concerns in the assessment of the long-term performance of a repository. Studies performed by other researchers indicated no systematic difference between natural earthquakes and mining-induced seismic events. The purpose of this field study at the Lucky Friday Mine is intended to obtain a better understanding regarding the local geohydrologic changes due to mining-induced seismicity and to evaluate analytical methods for simulation of these changes. Three saturated zones with faults and vein features were packed-off along a borehole drilled at approximately 20 degrees downward in a southerly direction from a depth about 1,737 m (5,700 ft) below surface for water pressure monitoring. The response of water pressure change to mine seismicity is found to be more pronounced in Zone 3, which contains the Lucky Friday Main Vein, than Zone 2, with the South Control Fault, and Zone 1, with the associated fractures parallel to the South Control Fault. The maximum observed pressure increase in Zone 3 was about 1.53 x 10 -2 MPa (2.22 psi) due to a seismic event of Richter drops in Zone 1 resulting from a number of seismic events are suspected to be related to slips along the associated fractures of the South Control Fault, or the South Control Fault itself, which initiated the seismic events. Water pressure increase in Zone 3 was found to be a function of event magnitude and distance

Subsurface characterization and geohydrologic site evaluation West Chestnut Ridge site

International Nuclear Information System (INIS)

1984-01-01

The West Chestnut Ridge Site at the Oak Ridge National Laboratory is being considered for use as a repository for low-level radioactive waste. The purposes of this study were to provide a geohydrological characterization of the site for use in pathways analysis, and to provide preliminary geotechnical recommendations that would be used for development of a site utilization plan. Subsurface conditions were investigated at twenty locations and observation wells were installed. Field testing at each location included the Standard Penetration Test and permeability tests in soil and rock. A well pumping test was ocmpleted at one site. Laboratory testing included permeability, deformability, strength and compaction tests, as well as index and physical property tests. The field investigations showed that the subsurface conditions include residual soil overlying a weathered zone of dolomite which grades into relatively unweathered dolomite at depth. The thickness of residual soil is typically 80 ft (24 m) on the ridges, but can be as little as 10 ft (3 m) in the valleys. Trench excavations to depths of 30 ft (9 m) should not present serious slope stability problems above the water table. On-site soils can be used for liners or trench backfill but these soils may require moisture conditioning to achieve required densities. 19 figures, 8 tables

Geohydrologic data collected from shallow neutron-access boreholes and resultant-preliminary geohydrologic evaluations, Yucca Mountain area, Nye County, Nevada

International Nuclear Information System (INIS)

Blout, D.O.; Hammermeister, D.P.; Loskot, C.L.; Chornack, M.P.

1994-01-01

In cooperation with the US Department of Energy, 74 neutron-access boreholes were drilled in and near the southwestern part of the Nevada Test Site, Nye County, Nevada. Drilling, coring, sample collection and handling, and lithologic and preliminary geohydrologic data are presented in this report. The boreholes were drilled in a combination of alluvium/colluvium, ash-flow tuff, ash-fall tuff, or bedded tuff to depths of 4.6 to 36.6 meters. Air was used as a drilling medium to minimize disturbance of the water content and water potential of drill cuttings, core, and formation rock. Drill cuttings were collected at approximately 0.6-meter intervals. Core was taken at selected intervals from the alluvium/colluvium using drive-coring methods and from tuff using rotary-coring methods. Nonwelded and bedded tuffs were continuously cored using rotary-coring methods. Gravimetric water-content and water-potential values of core generally were greater than those of corresponding drill cuttings. Gravimetric water-content, porosity, and water-potential values of samples generally decreased, and bulk density values increased, as the degree of welding increased. Grain-density values remained fairly constant with changes in the degree of welding. A high degree of spatial variability in water-content and water-potential profiles was noted in closely spaced boreholes that penetrate similar lithologic subunits and was also noted in adjacent boreholes located in different topographic positions. Variability within a thick lithologic unit usually was small. 18 refs., 21 figs., 17 tabs

Sault Tribe Wind Energy Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Toni Osterhout; Global Energy Concepts

2005-07-31

The Sault Tribe conducted a feasibility study on tribal lands in the Upper Peninsula of Michigan to determine the technical and economic feasibility of both small and large-scale wind power development on tribal lands. The study included a wind resource assessment, transmission system analysis, engineering and regulatory analyzes and assessments.

Geohydrologic reconnaissance of the upper Potomac River basin

Science.gov (United States)

Trainer, Frank W.; Watkins, Frank A.

1975-01-01

The upper Potomac River basin, in the central Appalachian region in Pennsylvania, Maryland, Virginia, and West Virginia, is a humid temperate region of diverse fractured rocks. Three geohydrologic terranes, which underlie large parts of the basin, are described in terms of their aquifer characteristics and of the magnitude and duration of their base runoff: (1) fractured rock having a thin regolith, (2) fractured rock having a thick regolith, and (3) carbonate rock. Crystalline rock in the mountainous part of the Blue Ridge province and shale with tight sandstone in the folded Appalachians are covered with thin regolith. Water is stored in and moves through fairly unmodified fractures. Average transmissivity (T) is estimated to be 150 feet squared per day, and average storage coefficient (S), 0.005. Base runoff declines rapidly from its high levels during spring and is poorly sustained during the summer season of high evapotranspiration. The rocks in this geohydrologic terrane are the least effective in the basin for the development of water supplies and as a source of dry-weather streamflow. Crystalline and sedimentary rocks in the Piedmont province and in the lowland part of the Blue Ridge province are covered with thick regolith. Water is stored in and moves through both the regolith and the underlying fractured rock. Estimated average values for aquifer characteristics are T, 200 feet squared per day, and S, 0.01. Base runoff is better sustained in this terrane than in the thin-regolith terrane and on the average .is about twice as great. Carbonate rock, in which fractures have been widened selectively by solution, especially near streams, has estimated average aquifer characteristics of T, 500 feet squared per day, and S, 0.03-0.04. This rock is the most effective in the basin in terms of water supply and base runoff. Where its fractures have not been widened by solution, the carbonate rock is a fractured-rock aquifer much like the noncarbonate rock. At low

A cask maintenance facility feasibility study

International Nuclear Information System (INIS)

Rennich, M.J.; Medley, L.G.; Attaway, C.R.

1989-01-01

The Oak Ridge National Laboratory (ORNL) is supporting the USDOE Office of Civilian Radioactive Waste Management (OCRWM) in developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, green field facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrieveable Storage (MRS) facility. The data, design, and estimated cost resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. The feasibility study was based on an assumed stand-alone green field configuration because of the flexibility this design approach provides. A stand-alone facility requires the inclusion with support functions as well as the primary process facilities thus yielding a comprehensive design evaluation and cost estimate. For example, items such as roads, security and waste processing which might be shared with an integrated or collocated facility have been fully costed in the feasibility study. Thus, while the details of the facility design might change, the overall concept used in the study can be applied to other facility configurations as planning for the total FWMS develops

Geohydrologic reconnaissance of Lake Mead National Recreation Area; Las Vegas Wash to Opal Mountain, Nevada

Science.gov (United States)

Laney, R.L.

1981-01-01

The study is a geohydrologic reconnaissance of about 170 square miles in the Lake Mead National Recreation Area from Las Vegas Wash to Opal Mountain, Nevada. The study is one of a series that describes the geohydrology of the recreation area and that indentifies areas where water supplies can be developed. Precipitation in this arid area is about 5 inches per year. Streamflow is seasonal and extremely variable except for that in the Colorado River, which adjoins the area. Pan evaporation is more than 20 times greater than precipitation; therefore, regional ground-water supplies are meager except near the Colorado River, Lake Mead, and Lake Mohave. Large ground-water supplies can be developed near the river and lakes, and much smaller supplies may be obtained in a few favorable locations farther from the river and lakes. Ground water in most of the areas probably contains more than 1,000 milligrams per liter of dissolved solids, but water that contains less than 1,000 milligrams per liter of dissolved solids can be obtained within about 1 mile of the lakes. Crystalline rocks of metamorphic, intrusive and volcanic origin crop out in the area. These rocks are overlain by conglomerate and mudstone of the Muddy Creek Formation, gravel and conglomerate of the older alluvium, and sand and gravel of the Chemehuevi Formation and younger alluvium. The crystalline rocks, where sufficiently fractured, yield water to springs and would yield small amounts of water to favorably located wells. The poorly cemented and more permeable beds of the older alluvium, Chemehuevi Formation, and younger alluvium are the better potential aquifers, particularly along the Colorado River and Lakes Mead and Mohave. Thermal springs in the gorge of the Colorado River south of Hoover Dam discharge at least 2,580 acre-feet per year of water from the volcanic rocks and metamorphic and plutonic rocks. The discharge is much greater than could be infiltrated in the drainage basin above the springs

100-BC-1 Operable Unit focused feasibility study

International Nuclear Information System (INIS)

Day, R.E.

1994-01-01

The standard Comprehensive Environmental Response, Compensation, and Liability Act feasibility study includes development and screening of alternatives (Phases 1 and 2) and the detailed analysis of alternatives (Phase 3). This focused feasibility study constitutes the Phase 3 portion of the feasibility study process for the remedial alternatives initially developed and screened in the 100 Area Feasibility Study Phases 1 and 2 (DOE-RL 1993a). The focused feasibility study process is conducted in two stages, a Process Document (DOE-RL 1994a) and an operable unit-specific focused feasibility study document, such as this one. The focused feasibility study process is performed by implementing a ''plug-in'' style approach; as defined in greater detail in the Process Document, which is a companion to this document. The objective of this focused feasibility study is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures for candidate waste sites associated with the 100-BC-1 Operable Unit which is located in the north-central part of the Hanford Site. The interim remedial measure candidate waste sites are determined in the Limited Field Investigation (DOE-RL 1993b). Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

The feasibility study: a health economics perspective

Directory of Open Access Journals (Sweden)

Brenda Gannon

2017-02-01

Full Text Available The remit of research funding bodies is to prioritise funding for research that is of relevance and of high quality. This in turn will aim to raise the quality of healthcare and benefit to patients. Researchers are faced with increasing demands and expectations from the public purse and patients. The emphasis is to improve the quality of their research, with the ultimate aim of improving population health. While guidelines on feasibility study methods concentrate heavily on trials, there appears less guidance on application of health economics within feasibility studies, yet these are a less costly way to determine first of all if a full randomised controlled trial (RCT is feasible. A feasibility study assesses if the study can be done in a small RCT type study. Since by definition, a feasibility study does not evaluate the outcome, researchers often omit the health economics aspects but do however include statistical analysis. This leaves a gap in interpretation for policy makers and potential funders. It also means that any resulting publication does not include relevant information and therefore comparison across studies in terms of difficulty in collecting cost data is not possible. The main aim of this commentary therefore, is to demonstrate a suggested health economics analysis within a feasibility study and to recommend to researchers to include these aspects from the conception of their intervention. This paper proposes a number of points, with rationale for each point, to indicate the health economics data and the potential benefits required for coherent interpretation of the feasibility of future economic evaluations in a full trial. Economic evaluation is necessary if implementation into standard care is anticipated. Therefore, collection and summary analysis of relevant data is good practice at each point of the intervention development. Current guidelines for economic evaluation, for example, The Medical Research Guidelines in the

Geohydrological studies for nuclear waste isolation at the Hanford Reservation. Volume I. Executive summary

International Nuclear Information System (INIS)

Apps, J.; Doe, T.; Doty, B.

1979-08-01

A study of the hydrology of the Pasco Basin near Richland, Washington, was initiated during FY 1978 as part of a long-term study on the feasibility of nuclear waste disposal in the Columbia River Basalt underlying the Hanford Reservation. This report summarizes the hydrology field program, Pasco Basin modeling, and groundwater chemistry program. Hanford well logs are also reviewed

Renewable Energy Feasibility Study Final Report

Energy Technology Data Exchange (ETDEWEB)

Rooney, Tim [Antares Group Inc.

2013-10-30

The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to assess the feasibility of solar photovoltaic (PV) installations. A solar energy project could provide a number of benefits to the Community in terms of potential future energy savings, increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a solar project’s overall feasibility, including: Technical appropriateness; Solar resource characteristics and expected system performance; Levelized cost of electricity (LCOE) economic assessment. The Gila River Indian Community (GRIC or the Community) contracted the ANTARES Group, Inc. (“ANTARES”) to prepare a biomass resource assessment study and evaluate the feasibility of a bioenergy project on Community land. A biomass project could provide a number of benefits to the Community in terms of increased employment, environmental benefits from renewable energy generation and usage, and increased energy self-sufficiency. The study addresses a number of facets of a biomass project’s overall feasibility, including: Resource analysis and costs; Identification of potential bioenergy projects; Technical and economic (levelized cost of energy) modeling for selected project configuration.

A cask maintenance facility feasibility study

International Nuclear Information System (INIS)

Rennich, M.J.; Medley, L.G.; Attaway, C.R.

1989-01-01

The Oak Ridge National Laboratory (ORNL) is developing a transportation system for spent nuclear fuel (SNF) and defense high level waste (HLW) as a part of the Federal Waste Management System (FWMS). In early 1988, a feasibility study was undertaken to design a stand-alone, ''green field'' facility for maintaining the FWMS casks. The feasibility study provided an initial layout facility design, an estimate of the construction cost, and an acquisition schedule for a Cask Maintenance Facility (CMF). The study also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrievable Storage (MRS) facility. The data, design, and estimated costs resulting from the study have been organized for use in the total transportation system decision-making process. Most importantly, the feasibility study also provides a foundation for continuing design and planning efforts. Fleet servicing facility studies, operational studies from current cask system operators, a definition of the CMF system requirements, and the experience of others in the radioactive waste transportation field were used as a basis for the feasibility study. In addition, several cask handling facilities were visited to observe and discuss cask operations to establish the functions and methods of cask maintenance expected to be used in the facility. Finally, a peer review meeting was held at Oak Ridge, Tennessee in August, 1988, in which the assumptions, design, layout, and functions of the CMF were significantly refined. Attendees included representatives from industry, the repository and transportation operations

Washoe Tribe Alternative Energy Feasibility Study Final Report

Energy Technology Data Exchange (ETDEWEB)

Johnson, Jennifer [Washoe Tribe of NV and CA

2014-10-01

The Washoe Tribe of Nevada and California was awarded funding to complete the Washoe Tribe Alternative Energy Feasibility Study project. The main goal of the project was to complete an alternative energy feasibility study. This study was completed to evaluate “the potential for development of a variety of renewable energy projects and to conduct an alternative energy feasibility study that determines which alternative energy resources have the greatest economic opportunity for the Tribe, while respecting cultural and environmental values” (Baker-Tilly, 2014). The study concluded that distributed generation solar projects are the best option for renewable energy development and asset ownership for the Washoe Tribe. Concentrating solar projects, utility scale wind projects, geothermal, and biomass resource projects were also evaluated during the study and it was determined that these alternatives would not be feasible at this time.

Do feasibility studies contribute to, or avoid, waste in research?

Science.gov (United States)

Morgan, Ben; Hejdenberg, Jennie; Hinrichs-Krapels, Saba; Armstrong, David

2018-01-01

In the context of avoiding research waste, the conduct of a feasibility study before a clinical trial should reduce the risk that further resources will be committed to a trial that is likely to 'fail'. However, there is little evidence indicating whether feasibility studies add to or reduce waste in research. Feasibility studies funded by the National Institute for Health Research's (NIHR) Research for Patient Benefit (RfPB) programme were examined to determine how many had published their findings, how many had applied for further funding for a full trial and the timeframe in which both of these occurred. A total of 120 feasibility studies which had closed by May 2016 were identified and each Principal Investigator (PI) was sent a questionnaire of which 89 responses were received and deemed suitable for analysis. Based on self reported answers from the PIs a total of 57 feasibility studies were judged as feasible, 20 were judged not feasible and for 12 it was judged as uncertain whether a full trial was feasible. The RfPB programme had spent approximately £19.5m on the 89 feasibility studies of which 16 further studies had been subsequently funded to a total of £16.8m. The 20 feasibility studies which were judged as not feasible potentially saved up to approximately £20m of further research funding which would likely to have not completed successfully. The average RfPB feasibility study took 31 months (range 18 to 48) to complete and cost £219,048 (range £72,031 to £326,830) and the average full trial funded from an RfPB feasibility study took 42 months (range 26 to 55) to complete and cost £1,163,996 (range £321,403 to £2,099,813). The average timeframe of feasibility study and full trial was 72 months (range 56 to 91), however in addition to this time an average of 10 months (range -7 to 29) was taken between the end of the feasibility study and the application for the full trial, and a further average of 18 months (range 13 to 28) between the

A study of critical paths for feasibility studies of mining projects

International Nuclear Information System (INIS)

Sayadi, R.

2002-01-01

This work develops a model for design and realisation of profitability's and feasibility studies of a mining project. The model provides the structure of various necessary procedures to establish the feasibility studies and presents a logical system of task sequencing and information circulating between tasks. The specifications of mining projects, particularly their duration, complexity and high costs, necessitate design and realisation of feasibility study bases on the sufficient understanding of task behaviour and the critical path method view. For this purpose, critical paths with the highest frequency of occurrence were studied through several simulations. In addition, the critical tasks and sub tasks with the most probability were identified. The model introduced in this paper can serve as a perfect tool in feasibility study of a mining project. It can also be used as a basis of future development of mining software

White Earth Biomass/Biogas Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Triplett, Michael

2015-03-12

The White Earth Nation examined the feasibility of cost savings and fossil energy reduction through the installation of biogas/biomass boiler at the tribal casino. The study rejected biogas options due to availability and site constraints, but found a favorable environment for technical and financial feasibility of installing a 5 MMBtu hot water boiler system to offset 60-70 percent of current fuel oil and propane usage.

Preliminary appraisal of the geohydrologic aspects of drainage wells, Orlando area, central Florida

Science.gov (United States)

Kimrey, Joel O.

1978-01-01

The Floridan aquifer contains two highly transmissive cavernous zones in the Orlando area: an upper producing zone about 150-600 feet below land surface; and a lower producing zone about 1,100-1,500 feet below land surface. Natural head differences are downward and there is hydraulic connection between the two producing zones. Drainage wells are finished open-end into the upper producing zone and emplace surface waters directly into that zone by gravity. Quantitatively, their use constitutes an effective method of artificial recharge. Their negative aspects relate to the probably poor, but unknown, quality of the recharge water. Caution is suggested in drawing definite and final conclusions on the overall geohydrologic and environmental effects of drainage wells prior to the collection and interpretation of a considerable quantity of new data. Though few ground-water pollution problems have been documented to date, the potential for such pollution should be seriously considered in light of the prob-able continuing need to use drainage wells; the probable volumes and quality of water involved; and the hydraulic relations between the two producing zones.

Human reliability data bank: feasibility study

International Nuclear Information System (INIS)

Comer, K.; Miller, D.P.; Donovan, M.

1984-01-01

The US Nuclear Regulatory Commission and Sandia National Laboratories have been developing a plan for a human reliability data bank since August 1981. This research is in response to the data needs of the nuclear power industry's probabilistic risk assessment community. The three phases of the program are to: (A) develop the data bank concept, (B) develop an implementation plan and conduct a feasibility study, and (C) assist a sponsor in implementing the data bank. The program is now in Phase B. This paper describes the methods used in the feasibility study. Decisions to be made in the future regarding full-scale implementation will be based, in part, on the outcome of this study. 3 references, 2 figures

Gasohol: economic feasibility study. Final report

Energy Technology Data Exchange (ETDEWEB)

David, M. L.; Hammaker, G. S.; Buzenberg, R. J.; Wagner, J. P.

1978-07-01

This report was prepared by Development Planning and Research Associates, Inc. under a contract with the Energy Research and Development Center of the University of Nebraska in cooperation with the Agricultural Products Industrial Utilization Committee and the State of Nebraska. Funding for this study was provided to the Energy Research and Development Center by the U.S. Department of Energy and the Old West Regional Commission. The primary objective of the study was to: determine the fiscal and market conditions under which the production of gasohol would be profitable for private producers. For purposes of this study, gasohol is a motor fuel consisting of 10 percent agriculturally-derived anhydrous ethanol and 90 percent unleaded gasoline. The study assumes that gasohol can be a fuel substitute for gasoline; indeed, the cost of gasoline will significantly influence that for gasohol. Gasoline prices are determined by factors external to ethanol; thus, the economic feasibility study of gasohol is in large part an economic feasibility study of fuel-grade ethanol production. More specifically, the study examined the following: the technical aspects of distributing, marketing, and using gasohol; the costs of the distribution and marketing of ethanol and gasohol; the energy balance of ethanol production; the cost of producing ethanol; the factors influencing ehtanol plant size and location; and the conditions that would make ethanol economicaly feasible for private producers.

Feasibility and Pilot Studies in Palliative Care Research: A Systematic Review.

Science.gov (United States)

Jones, Terry A; Olds, Timothy S; Currow, David C; Williams, Marie T

2017-07-01

Feasibility and pilot study designs are common in palliative care research. Finding standard guidelines on the structure and reporting of these study types is difficult. In feasibility and pilot studies in palliative care research, to determine 1) how commonly a priori feasibility are criteria reported and whether results are subsequently reported against these criteria? and 2) how commonly are participants' views on acceptability of burden of the study protocol assessed? Four databases (OVID Medline, EMBASE, CINAHL, and PubMed via caresearch.com.au.) were searched. Search terms included palliative care, terminal care, advance care planning, hospice, pilot, feasibility, with a publication date between January 1, 2012 and December 31, 2013. Articles were selected and appraised by two independent reviewers. Fifty-six feasibility and/or pilot studies were included in this review. Only three studies had clear a priori criteria to measure success. Sixteen studies reported participant acceptability or burden with measures. Forty-eight studies concluded feasibility. The terms "feasibility" and "pilot" are used synonymously in palliative care research when describing studies that test for feasibility. Few studies in palliative care research outline clear criteria for success. The assessment of participant acceptability and burden is uncommon. A gold standard for feasibility study design in palliative care research that includes both clear criteria for success and testing of the study protocol for participant acceptability and burden is needed. Such a standard would assist with consistency in the design, conduct and reporting of feasibility and pilot studies. Copyright © 2017 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All rights reserved.

General discussion of feasibility study

International Nuclear Information System (INIS)

Calori, F.

1976-01-01

Fundamentals, objectives and parameters of feasibility studies in the field of nuclear power project planning are discussed in a general way. Technical and economic problems to be considered are pointed out. In special cases, IAEA offers its aid and support. (UA) [de

Geohydrology of the Aucilla-Suwannee-Ochlockonee River Basin, south-central Georgia and adjacent parts of Florida

Science.gov (United States)

Torak, Lynn J.; Painter, Jaime A.; Peck, Michael F.

2010-01-01

Major streams and tributaries located in the Aucilla-Suwannee-Ochlockonee (ASO) River Basin of south-central Georgia and adjacent parts of Florida drain about 8,000 square miles of a layered sequence of clastic and carbonate sediments and carbonate Coastal Plain sediments consisting of the surficial aquifer system, upper semiconfining unit, Upper Floridan aquifer, and lower confining unit. Streams either flow directly on late-middle Eocene to Oligocene karst limestone or carve a dendritic drainage pattern into overlying Miocene to Holocene sand, silt, and clay, facilitating water exchange and hydraulic connection with geohydrologic units. Geologic structures operating in the ASO River Basin through time control sedimentation and influence geohydrology and water exchange between geohydrologic units and surface water. More than 300 feet (ft) of clastic sediments overlie the Upper Floridan aquifer in the Gulf Trough-Apalachicola Embayment, a broad area extending from the southwest to the northeast through the center of the basin. These clastic sediments limit hydraulic connection and water exchange between the Upper Floridan aquifer, the surficial aquifer system, and surface water. Accumulation of more than 350 ft of low-permeability sediments in the Southeast Georgia Embayment and Suwannee Strait hydraulically isolates the Upper Floridan aquifer from land-surface hydrologic processes in the Okefenokee Basin physiographic district. Burial of limestone beneath thick clastic overburden in these areas virtually eliminates karst processes, resulting in low aquifer hydraulic conductivity and storage coefficient despite an aquifer thickness of more than 900 ft. Conversely, uplift and faulting associated with regional tectonics and the northern extension of the Peninsular Arch caused thinning and erosion of clastic sediments overlying the Upper Floridan aquifer southeast of the Gulf Trough-Apalachicola Embayment near the Florida-Georgia State line. Limestone dissolution in

Technical design aspects of Feasibility Study-II

International Nuclear Information System (INIS)

Zisman, Michael S.

2001-01-01

Feasibility Study-II examined a high-performance Neutrino Factory providing 1 x 10 20 neutrinos per year aimed at a long-baseline detector. The Study was sponsored jointly by BNL and the Neutrino Factory and Muon Collider Collaboration ration (MC) and is based on a 1 MW proton driver operating at 24 GeV, i.e., an upgraded version of the AGS accelerator. Compared with the earlier FNAL-sponsored study (Feasibility Study-I), there is a sixfold improvement in performance. Here we describe details of the implementation of Study-II concepts and discuss their efficacy. Alternative approaches that will be pursued in follow-on R and D activities are also described briefly

Conceptual Thermal Treatment Technologies Feasibility Study

International Nuclear Information System (INIS)

Suer, A.

1996-01-01

This report presents a conceptual Thermal Treatment Technologies Feasibility Study (FS) for the Savannah River Site (SRS) focusing exclusively on thermal treatment technologies for contaminated soil, sediment, or sludge remediation projects

Use of Geohydrologic Response Functions in the assessment of deep nuclear waste repositories: assessment of effectiveness of geologic isolation systems

International Nuclear Information System (INIS)

Nelson, R.W.

1981-05-01

Geohydrologic Response Functions (GRFs) interrelate the three vital factors needed in the repository decision-making process: the quantity, arrival time, and location of contamination reaching the biosphere. GRFs further focus attention upon two related and additive parameters: the initial delay time and delay spread time. After the principal site selection, the GRFs may be applied to obtain more detailed performance evaluations concerning specific nuclides or waste components, specific results for various types of accidental release, and effects of a variety of contaminant source terms or leach models. The response functions may be applied to consider contaminant reductions and delays through material sorption as well as through a variety of other interactions and effects

Feasibility study on large pool-type LMFBR

International Nuclear Information System (INIS)

1984-01-01

A feasibility study has been conducted from 1981 FY to 1983 FY, in order to evaluate the feasibility of a large pool-type LMFBR under the Japanese seismic design condition and safety design condition, etc. This study was aimed to establish an original reactor structure concept which meets those design conditions especially required in Japan. In the first year, preceding design concepts had been reviewed and several concepts were originated to be suitable to Japan. For typical two of them being selected by preliminary analysis, test programs were planned. In the second year, more than twenty tests with basic models had been conducted under severe conditions, concurrently analytical approaches were promoted. In the last year, larger model tests were conducted and analytical methods have been verified concerning hydrodynamic effects on structure vibration, thermo-hydraulic behaviours in reactor plena and so on. Finally the reactor structure concepts for a large pool-type LMFBR have been acknowledged to be feasible in Japan. (author)

Dual-gated cardiac PET-clinical feasibility study

Energy Technology Data Exchange (ETDEWEB)

Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani [Turku PET Centre, PO BOX 52, Turku (Finland); Durand-Schaefer, Nicolas [General Electric Medical Systems, Buc (France); Pietilae, Mikko [Turku University Hospital, Department of Internal Medicine, Turku (Finland); Kiss, Jan [Turku University Hospital, Department of Surgery, Turku (Finland)

2010-03-15

Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

Dual-gated cardiac PET-clinical feasibility study

International Nuclear Information System (INIS)

Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani; Durand-Schaefer, Nicolas; Pietilae, Mikko; Kiss, Jan

2010-01-01

Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

Feasibility Study: New Knowledge Demands in Turbulent Business World

Science.gov (United States)

Sprice, Renate; Kirikova, Marite

Feasibility study is one of the early activities in information systems (IS) development when important decisions regarding choice among several possible systems development alternatives are to be made. In times of relatively stable business environment and waterfall model as a systems development approach, the role and methods of feasibility study where quite clear (Kendall and Kendall 1995). However, new software development methods and the necessity to develop more rapidly new IS or their parts may. challenge the possibility to evaluate project feasibility in the early stages of IS development.

COLD-SAT feasibility study safety analysis

Science.gov (United States)

Mchenry, Steven T.; Yost, James M.

1991-01-01

The Cryogenic On-orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite presents some unique safety issues. The feasibility study conducted at NASA-Lewis desired a systems safety program that would be involved from the initial design in order to eliminate and/or control the inherent hazards. Because of this, a hazards analysis method was needed that: (1) identified issues that needed to be addressed for a feasibility assessment; and (2) identified all potential hazards that would need to be controlled and/or eliminated during the detailed design phases. The developed analysis method is presented as well as the results generated for the COLD-SAT system.

The environmental energy sector programme. Poland: Feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The Danish Ministry of Energy has granted financial aid to the preparation of a feasibility study necessary for the procurement of a financial solution to the modernisation of the combined heat and power plant in the city of Zielona Gora.The overall objectives of the Feasibility Study are to: establish new efficient power capacity in the south-west region of Poland, increase the energy efficiency, reduce the impact on the environment, utilise the local natural gas available which cannot be used in the national gas grid and reduce the costs of energy supply.The specific objective of this feasibility study is to obtain the best possible financing of the erection of a new CPH plant in Zielona Gora. The plant shall be designed to utilise the local resources of natural gas and to supply heat to the district heating grid in accordance with long-term planning strategies. (EHS)

Overview of geologic and geohydrologic conditions at the Finnsjoen site and its surroundings

International Nuclear Information System (INIS)

Ahlbom, K.; Tiren, S.

1991-01-01

The geologic and tectonic conditions of the Finnsjoen site and its surroundings have been studied on several scales ranging from regional to site scale. The Finnsjoen study is situated within a 50 square km shear lens. This lens is a part of a regional, c.20-30 km wide, WNW trending shear belt that was developed 1600-1800 million years ago. The final repository for reactor waste at Forsmark is also situated within this shear belt. The Finnsjoen Rock Block, bounded by regional and semi-regional fracture zones, constitute the main part of the Finnsjoen site. The size of the block is about 6 square km. A northeasterly trending fracture zone, Zone 1, divides this block into two lower order blocks, the northern and the southern block. In general, interpreted fracture zones, as well as the rock mass in general, are far better known in the northern Finnsjoen block compared to the southern block. This is due to extensive and detailed investigations of a gently dipping fracture zone, Zone 2, in the northern block. A tectonic model including 14 fracture zones is suggested for the Finnsjoen site and its surroundings. These zones have mainly been interpreted from lineament maps and to some extent from borehole measurements. The lack of borehole data implies that many of interpreted fracture zones, especially in the southern block outside the Finnsjoen site, should be regarded as tentative. The good general knowledge of the geologic and geohydrologic conditions in the northern Finnsjoen block, and possible stagnant groundwater conditions below Zone 2, makes the northern block the most suitable location for the generic repository at the Finnsjoen site. (authors)

Radiation processing of flue gases: Guidelines for feasibility studies

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects.

Radiation processing of flue gases: Guidelines for feasibility studies

International Nuclear Information System (INIS)

2000-12-01

The aim of this publication is to facilitate the performance of feasibility studies for Electron Beam flue gas cleanup projects by providing guidelines to conduct these studies and compiling information on the state of the art. This document summarizes the contents of a feasibility study; discusses the main items in plant construction, measurement and control systems, radiation safety and building construction; and lists the required economic data for internationally funded projects

Feasibility study on small modular reactors for modern microgrids

Energy Technology Data Exchange (ETDEWEB)

Islam, R.; Gabbar, H.A., E-mail: hossam.gabbar@uoit.ca [Univ. of Ontario Inst. of Technology, Faculty of Energy Systems and Nuclear Science, Oshawa, Ontario (Canada)

2013-07-01

Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

Feasibility study on small modular reactors for modern microgrids

International Nuclear Information System (INIS)

Islam, R.; Gabbar, H.A.

2013-01-01

Microgrid is a solution of conventional power grid problem and offer sustainable decentralized power system. Microgrid with modern distributed energy resources (DER) could play an important role to alleviate dependency on the main electricity grid. Distributed energy resource comprises wind turbine, solar photovoltaic, diesel generator, gas engine, micro turbine, fuel cells, etc.Due to the gap between typical loads and supply within microgrid, larger scale energy generation could provide a possible solution to balance power demand and supply. Feasibility study of Small Nuclear Power Plant, such as Small Modular reactor (SMR), within microgrids could be achieved via different cases. To achieve the target, a comprehensive feasibility study is conducted on microgrid with SMR through electricity generation profiles, geographical and environmental assessment, as well as cost analysis using simulation practices and data analysis.Also potency of SMRs is analyzed. Parameters and Key Performance Indicators (KPIs) could be analyzed to achieve feasible solution of microgrids with small modular reactor (SMR) to improve the overall microgrid performance.The study shows that SMR could be a feasible solution if microgrid parameters are selected properly. (author)

Geohydrology, water quality, and simulation of ground-water flow in the vicinity of a former waste-oil refinery near Westville, Indiana, 1997-2000

Science.gov (United States)

Duwelius, Richard F.; Yeskis, Douglas J.; Wilson, John T.; Robinson, Bret A.

2002-01-01

Geohydrologic and water-quality data collected during 1997 through 2000 in the vicinity of a former waste-oil refinery near Westville, Indiana, define a plume of 1,4-dioxane in ground water that extends to the southwest approximately 0.8 miles from the refinery site. Concentrations of 1,4-dioxane in the plume ranged from 3 to 31,000 micrograms per liter. Ground water containing 1,4-dioxane is discharged to Crumpacker Ditch, approximately one-half mile west of the refinery site. Concentrations of 1,4-dioxane detected in surface water ranged from 8 to 140 micrograms per liter; 1,4-dioxane also is transported in ground water beneath the ditch.

TMI-2 fuel-recovery plant. Feasibility study

International Nuclear Information System (INIS)

Evans, D.L.

1982-12-01

This project is a feasibility study for constructing a TMI-2 core Fuel Recovery Plant at the Idaho National Engineering Laboratory (INEL). The primary objectives of the Fuel Recovery Plant (FRP) are to recover and account for the fuel and to process, isolate, and package the waste material from the TMI-2 core. This feasibility study is predicated on a baseline plant and covers its design, fabrication, installation, testing and operation. Alternative methods for the disposal of the TMI-2 core have also been considered, but not examined in detail for their feasibility. The FRP will receive TMI-2 fuel in canisters. The fuel will vary from core debris to intact fuel assemblies and include some core structural materials. The canister contents will be shredded and subsequently fed to a dissolver. Uranium, plutonium, fission products, and some core structural material will be dissolved. The uranium will be separated by solvent extraction and solidified by calcination. The plutonium will also be separated by solvent extraction and routed to the Plutonium Extraction Facility. The wastes will be packaged for further treatment, temporary storage or permanent disposal

Ute Mountain Ute Tribe Community-Scale Solar Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Rapp, Jim [Parametrix; Knight, Tawnie [Ute Mountain Ute Tribe

2014-01-30

Parametrix Inc. conducted a feasibility study for the Ute Mountain Ute Tribe to determine whether or not a community-scale solar farm would be feasible for the community. The important part of the study was to find where the best fit for the solar farm could be. In the end, a 3MW community-scale solar farm was found best fit with the location of two hayfield sites.

Technical summary of groundwater quality protection program at Savannah River Plant. Volume 1. Site geohydrology, and solid and hazardous wastes

International Nuclear Information System (INIS)

Christensen, E.J.; Gordon, D.E.

1983-12-01

The program for protecting the quality of groundwater underlying the Savannah River Plant (SRP) is described in this technical summary report. The report is divided into two volumes. Volume I contains a discussion of the general site geohydrology and of both active and inactive sites used for disposal of solid and hazardous wastes. Volume II includes a discussion of radioactive waste disposal. Most information contained in these two volumes is current as of December 1983. The groundwater quality protection program has several elements which, taken collectively, are designed to achieve three major goals. These goals are to evaluate the impact on groundwater quality as a result of SRP operations, to restore or protect groundwater quality by taking corrective action as necessary, and to ensure disposal of waste materials in accordance with regulatory guidelines

The Economic Pre-feasibility Study of Madura Nuclear Desalination System

International Nuclear Information System (INIS)

Djoko-Birmanto, Moch; Suparman

2004-01-01

The feasibility study is needed in the planning of construction of NPPs SMART type coupled with desalination technology of MED tpe to produce clean water in Madura island. One important part of the feasibility study is the economical and financial analysis. The feasibility criteria of nuclear desalination project is analyzed by using the general parameters that is commonly used in evaluating a project, which is Financial Net Present Value (FNPV), Financial Internal Rate of Return (FIRR) and Payback Period. The calculation result shows that with the electricity selling price of 54.17 mills/KWh, for entirely project funded by the foreign loan, local loan and equity, it could be obtained FIRR 12.73 %, FNPV US$ 75.29 million and Payback Period is 8 years. By seeing from the project feasibility criteria, this nuclear desalination project can be feasible and the investment aspect shows that this project is beneficial because the capital return rate is rather high, the benefit in the end of the economic life-time is rather big and the capital payback period is fast. (author)

Feasibility study on tandem fuel cycle

International Nuclear Information System (INIS)

Han, P.S.; Suh, I.S.; Rim, C.S.; Kim, B.K.; Suh, K.S.; Ro, S.K.; Juhn, P.I.; Kim, S.Y.

1983-01-01

The objective of this feasibility study is to review and assess the current state of technology concerning the tandem fuel cycle. Based on the results from this study, a long-term development plan suitable for Korea has been proposed for this cycle, i.e., the PWR → CANDU tandem fuel cycle which used plutonium and uranium, recovered from spent PWR fuel by co-processing, as fuel material for CANDU reactors. (Author)

A Feasibility study of a mining business

Directory of Open Access Journals (Sweden)

Cehlár Michal

2001-06-01

Full Text Available The economic evaluation of a project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation.There are various of detail required at the different stages of evaluation in the project, from the "quick and dirty" overview to the pre-feasibility study, through a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in project and can be used at all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the review can pursue in more detail using an increasingly more comprehensive checklist for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation.A feasibility study is defined as an assessment of all aspects of a project including technical, infrastructural, environmental, social, legislative and commercial factors, which is sufficiently detailed to support a decision on the implementation. Each project has an associated level of risk. For a proposed investment to increase the value of a firm's stock, it should have a higher expected rate of return than shareholders require for assuming that risk. Since investors demand for a higher potential returns from a riskier project, the cost of capital depends on the venture's risk.

MacMillan Pier Transportation Center Feasibility Study.

Science.gov (United States)

2006-06-01

The MacMillan Pier Transportation Center Feasibility Study examines two potential sites (landside and waterside) for a transportation center that provides a range of tourist and traveler information. It would serve as a gateway for Provincetown and t...

Feasibility study for siting of a deep repository within the Storuman municipality

International Nuclear Information System (INIS)

1995-01-01

It is SKB's task to gather a broad body of information for the siting of a deep repository for Sweden's spent nuclear fuel and other long-lived radioactive waste. The criteria presented by SKB serve as guidelines for the siting studies. Overviews of siting factors are compiled in general siting studies of all or parts of Sweden. Feasibility studies examine the siting prospects in potentially suitable and interested municipalities. SKB plans to carry out feasibility studies in five to ten municipalities in different parts of the country. General studies and feasibility studies are primarily based on existing material. The feasibility study in Storuman is the first to be conducted. It began during the second half of 1993 with the conclusion of an agreement between the municipality and SKB. SKB has been in charge of the execution of the feasibility study. SKB has been responsible for the summary provided in a status report published in June 1994, as well as for the conclusions and evaluations in this final report. Altogether about 30 reports have been published within the framework of the feasibility study. The purpose of the various studies have been to describe, in as much detail as possible, the prospects for siting a deep repository in the municipality of Storuman, and to shed light on the possible positive and negative consequences of such a siting. The feasibility study has led to a discussion within the municipality and the region concerning the siting of a deep repository. In SKB's opinion, this gives all those concerned ample opportunity to become acquainted with the issues and to assert their interests and present their viewpoints at an early stage. 55 refs

Review of criterias for shallow burial sites and geohydrological evaluation around the site of temporary storage of low-level solid radioactive wastes of IPEN-CNEN/SP

International Nuclear Information System (INIS)

Chandra, U.; Marcelino, S.

1986-01-01

Some comments about norms of pollutants release from nuclear and other industries are made. For radioactive discharges, the strictly implemented national norms/criterias, are much more advanced technically than those existing for other pollutants. Based on the criterias of site selection and site evaluations, the site of IPEN for temporary storage of low level solid radioactive waster has been evaluated geohydrologically. Rainfall infiltration rate (297 cm/y) was determined by tritium labelling technique. Ground water velocity (max. 46.1 cm/d) and direction (to north) was determined by various radioactive (Br-82, I-131, Cr-51) tracers using single well techniques. (Author) [pt

Three Affliated Tribes Renewable Energy Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Belvin Pete; Kent Good; Krista Gordon; Ed McCarthy,

2006-05-26

The Three Affliated Tribes on the Fort Berthold Reservation studied the feasibility of a commercial wind facility on land selected and owned by the Tribes and examined the potential for the development of renewable energy resources on Tribal Lands.

Restoring effective sleep tranquility (REST): A feasibility and pilot study.

Science.gov (United States)

Eakman, Aaron M; Schmid, Arlene A; Henry, Kimberly L; Rolle, Natalie R; Schelly, Catherine; Pott, Christine E; Burns, Joshua E

2017-06-01

The purpose of this pilot study was to establish the feasibility of completing a future controlled trial of a multi-component cognitive behavioral therapy for insomnia program for military veterans with sleep disturbance. This was a single-arm feasibility and pilot study. Participants were United States post-9/11 veterans with service-connected injuries, university students, and had self-reported sleep disturbances. Restoring Effective Sleep Tranquility was a multi-component cognitive behavioral therapy for insomnia intervention consisting of seven sessions of group therapy and eight 1:1 sessions delivered by occupational therapists. Feasibility and pilot indicators were process, resources, management, and scientific, including pre-post-assessments of sleep difficulties, dysfunctional sleep beliefs, participation, and pain interference. Indicators were supportive of feasibility, including reduced sleep difficulties (for example Medical Outcomes Study Sleep Measure [ t  = 3.29, p  = .02]), reduced nightmares: t  = 2.79, p  = .03; fewer dysfunctional sleep beliefs: t  = 3.63, p  = .01, and greater ability to participate in social roles: t  = -2.86, p  = .03, along with trends towards improved satisfaction with participation and reduced pain interference. The Restoring Effective Sleep Tranquility program may reduce sleep difficulties and improve participation in US veterans with service-connected injuries, and evidence indicates a controlled trial would be feasible to deliver.

Feasibility Study on HYSOL CSP

DEFF Research Database (Denmark)

Nielsen, Lars Henrik; Baldini, Mattia; Skytte, Klaus

2016-01-01

integrated HYSOL concept, therefore, becomes a fully dispatchable (offering firm power) and fully renewable energy source (RES) based power supply alternative, offering CO2-free electricity in regions with sufficient solar resources. The economic feasibility of HYSOL configurations is addressed in this paper....... The CO2 free HYSOL alternative is discussed relative to conventional reference firm power generation technologies. In particular the HYSOL performance relative to new power plants based on natural gas (NG) such as open cycle or combined cycle gas turbines (OCGT or CCGT) are in focus. The feasibility...

Feasibility study for siting of a deep repository within the Storuman municipality

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-01

It is SKB`s task to gather a broad body of information for the siting of a deep repository for Sweden`s spent nuclear fuel and other long-lived radioactive waste. The criteria presented by SKB serve as guidelines for the siting studies. Overviews of siting factors are compiled in general siting studies of all or parts of Sweden. Feasibility studies examine the siting prospects in potentially suitable and interested municipalities. SKB plans to carry out feasibility studies in five to ten municipalities in different parts of the country. General studies and feasibility studies are primarily based on existing material. The feasibility study in Storuman is the first to be conducted. It began during the second half of 1993 with the conclusion of an agreement between the municipality and SKB. SKB has been in charge of the execution of the feasibility study. SKB has been responsible for the summary provided in a status report published in June 1994, as well as for the conclusions and evaluations in this final report. Altogether about 30 reports have been published within the framework of the feasibility study. The purpose of the various studies have been to describe, in as much detail as possible, the prospects for siting a deep repository in the municipality of Storuman, and to shed light on the possible positive and negative consequences of such a siting. The feasibility study has led to a discussion within the municipality and the region concerning the siting of a deep repository. In SKB`s opinion, this gives all those concerned ample opportunity to become acquainted with the issues and to assert their interests and present their viewpoints at an early stage. 55 refs.

Technical feasibility study on polycarbonate solar panels

NARCIS (Netherlands)

Hackmann, M.M.; Meuwissen, M.H.H.; Bots, T.L.; Buijs, J.A.H.M.; Broek, K.M.; Kinderman, R.; Tanck, O.B.F.; Schuurmans, F.M.

2004-01-01

This paper describes a technical feasibility study on the application of polycarbonate (PC) plates in a superstrate photovoltaic module design. The lamination process was performed in a conventional laminator apparatus using low temperature curing (100°C) ethylene-vinyl-acetate (EVA) as the potting

Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility

International Nuclear Information System (INIS)

King, J.W.

1993-01-01

The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction

Feasibility Study for a Hopi Utility-Scale Wind Project

Energy Technology Data Exchange (ETDEWEB)

Kendrick Lomayestewa

2011-05-31

The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. The goal of this project was to investigate the feasibility for the generation of energy from wind and to parallel this work with the development of a tribal utility organization capable of undertaking potential joint ventures in utility businesses and projects on the Hopi reservation. Wind resource assessments were conducted at two study sites on Hopi fee simple lands located south of the city of Winslow. Reports from the study were recently completed and have not been compared to any existing historical wind data nor have they been processed under any wind assessment models to determine the output performance and the project economics of turbines at the wind study sites. Ongoing analysis of the wind data and project modeling will determine the feasibility of a tribal utility-scale wind energy generation.

INTEC High-Level Waste Studies Universal Solvent Extraction Feasibility Study

International Nuclear Information System (INIS)

Banaee, J.; Barnes, C.M.; Battisti, T.; Herrmann, S.; Losinski, S.J.; McBride, S.

2000-01-01

This report summarizes a feasibility study that has been conducted on the Universal Solvent Extraction (UNEX) Process for treatment and disposal of 4.3 million liters of INEEL sodium-bearing waste located at the Idaho Nuclear Technology and Engineering Center. This feasibility study covers two scenarios of treatment. The first, the UNEX Process, partitions the Cs/Sr from the SBW and creates remote-handled LLW and contact-handled TRU waste forms. Phase one of this study, covered in the 30% review documents, dealt with defining the processes and defining the major unit operations. The second phase of the project, contained in the 60% review, expanded on the application of the UNEX processes and included facility requirements and definitions. Two facility options were investigated for the UNEX process, resulting in a 2 x 2 matrix of process/facility scenarios as follows: Option A, UNEX at Greenfield Facility, Option B, Modified UNEX at Greenfield Facility, Option C, UNEX at NWCF, th is document, covers life-cycle costs for all options presented along with results and conclusions determined from the study

Final Technical Report: Renewable Energy Feasibility Study and Resources Assessment

Energy Technology Data Exchange (ETDEWEB)

Rivero, Mariah [BEC Environmental, Inc., Las Vegas, NV (United States)

2016-02-28

In March 2011, the U.S. Department of Energy (DOE) awarded White Pine County, Nevada, a grant to assess the feasibility of renewable resource-related economic development activities in the area. The grant project included a public outreach and training component and was to include a demonstration project; however, the demonstration project was not completed due to lack of identification of an entity willing to locate a project in White Pine County. White Pine County completed the assessment of renewable resources and a feasibility study on the potential for a renewable energy-focused economic sector within the County. The feasibility study concluded "all resources studied were present and in sufficient quantity and quality to warrant consideration for development" and there were varying degrees of potential economic impact based on the resource type and project size. The feasibility study and its components were to be used as tools to attract potential developers and other business ventures to the local market. White Pine County also marketed the County’s resources to the renewable energy business community in an effort to develop contracts for demonstration projects. The County also worked to develop partnerships with local educational institutions, including the White Pine County School District, conducted outreach and training for the local community.

PV solar system feasibility study

International Nuclear Information System (INIS)

Ashhab, Moh’d Sami S.; Kaylani, Hazem; Abdallah, Abdallah

2013-01-01

Highlights: ► This research studies the feasibility of PV solar systems. ► The aim is to develop the theory and application of a hybrid system. ► Relevant research topics are reviewed and some of them are discussed in details. ► A prototype of the PV solar system is designed and built. - Abstract: This research studies the feasibility of PV solar systems and aims at developing the theory and application of a hybrid system that utilizes PV solar system and another supporting source of energy to provide affordable heating and air conditioning. Relevant research topics are reviewed and some of them are discussed in details. Solar heating and air conditioning research and technology exist in many developed countries. To date, the used solar energy has been proved to be inefficient. Solar energy is an abundant source of energy in Jordan and the Middle East; with increasing prices of oil this source is becoming more attractive alternative. A good candidate for the other system is absorption. The overall system is designed such that it utilizes solar energy as a main source. When the solar energy becomes insufficient, electricity or diesel source kicks in. A prototype of the PV solar system that operates an air conditioning unit is built and proper measurements are collected through a data logging system. The measured data are plotted and discussed, and conclusions regarding the system performance are extracted.

PUEBLO OF ZIA RENEWABLE ENERGY DEVELOPMENT FEASIBILITY STUDY

Energy Technology Data Exchange (ETDEWEB)

Pino, Peter M. [Tribal Administrator (Ret.), Pueblo of Zia; Lakshman, Jai [Project Manager (NDA) for Pueblo of Zia; Toole, G. Loren [Principal Investigator, Los Alamos National Laboratory - Energy Analysis Team/ CCS-3, D-4; Hand, Dan [P.E., Sustainable Enginerring; Witcher, James; Emerson, Michael A. [Senior V.P., ARES Corporation; Turner, Jeremy [Executive Director, NM Renewable Energy Transmission Authority; Sandidge, Wendy [Director of Operations, NM Community Capital

2014-06-30

The Pueblo of Zia will conduct a comprehensive feasibility study for best-use application(s) for development of renewable energy resources on its tribally held TRUST lands (i.e., Trust Lands of Zia Indian Reservation). The feasibility study is essential for determining the technical and economic viability of a future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe. Project Objectives: The feasibility study is essential for determining the technical and economic viability of future renewable project(s) on Zia tribal lands, including the potential economic and environmental benefits for the Tribe to: 1. Provide a balanced local renewable power supply for Zia Pueblo, its members, tribal offices, schools and buildings, and businesses on tribal lands 2. Provide a firm power supply for export and commercial market distribution 3. Provide economic development for the Tribe and its members, including job training and creation, each in accordance with the goals and objectives as conveyed by the Pueblo of Zia Tribal Council, Tribal Administration, and outlined in The Pueblo of Zia Comprehensive Plan and Pueblo of Zia — Zia Enterprise Zone Master Plan. A key goal of the study is to analyze the integrated development of solar, geothermal, and wind renewable energy resources at Zia Pueblo, with added potential to combine gas-fired generation to accomplish energy firming. Geothermal offers a base load source of energy, providing power continuously for end users. Wind and solar offer intermediate and peaking sources of energy, which can be harvested throughout the day, with periods of variable but predicable output. Variability will be managed in an integrated manner, using Zia Pueblo's combined renewable resources to generate high-quality power. Tasks are intended to collect, catalog, map, and analyze existing data on Zia Pueblo's renewable energy resource base and then match resource attributes with

Human-induced landscape changes and geo-hydrological risk: the Rupinaro catchment, Liguria, Italy

Science.gov (United States)

Giostrella, Paola; Faccini, Francesco; Maggi, Roberto; Cesare Mondini, Alessandro; Tarolli, Paolo; Guzzetti, Fausto

2015-04-01

Small and steep watersheds are typical of Liguria, northern Italy. In these small watersheds, geo-hydrological hazards, including flash floods and shallow landslides, caused by high intensity rainfall are frequent and abundant. In the coastal valleys of Liguria, narrow flood plains have hosted human settlements and communication lines since the protohistoric period. Since then, a variety of human activities have modified the natural landscape significantly, and chiefly through land-use changes first in the flood-plains, and next along the slopes. We have studied the 11-square km Rupinaro catchment, west of Chiavari, which has been inhabited since the 8th century BC. Progressive human actions have modified the main river and its tributaries, which have become narrower and canalized, and locally they were covered completely. Human actions have also contributed to the increase in the runoff coefficients, and to the progradation of the main river into the Ligurian Sea. Demographic growth, socio-economic development and urbanization are the main drivers for the land use changes occurred in the Rupinaro catchment. Through a combined analysis of archaeological and palynologycal data, and the multi-temporal analysis of historical maps, aerial photographs and satellite imagery of different vintages, we have reconstructed phases of modifications of the river and the tributaries. We determined the land use changes calculating the loss of soil, analyzing statistics of buildings and demography for the last 150 years, and interpreting historical maps and aerial and satellite imagery. We found that land reclamations, the construction of embankments, and the rectification of rivers are the main human actions performed to obtain building areas along the main river course. Expansion of urban settlements in flood prone areas, and even in the main riverbed, have reached a critical limit has shown by the destructive flood event that has affected the Rupinaro catchment, and chiefly the

Feasibility study on volcanic power generation system

Energy Technology Data Exchange (ETDEWEB)

None

1977-07-01

Investigations were carried out to determine the feasibility of volcanic power generation on Satsuma Io Island. Earthquakes were studied, as were the eruptions of subaerial and submarine hot springs. Hydrothermal rock alteration was studied and electrical surveys were made. General geophysical surveying was performed with thermocameras and radiation monitoring equipment. In particular, the Toyoba mine was studied, both with respect to its hot spring and its subsurface temperatures.

IPNS upgrade: A feasibility study

International Nuclear Information System (INIS)

1995-04-01

Many of Argonne National Laboratory's (ANL's) scientific staff members were very active in R ampersand D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R ampersand D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL's Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately

IPNS upgrade: A feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

Many of Argonne National Laboratory`s (ANL`s) scientific staff members were very active in R&D work related to accelerator-based spoliation sources in the 1970s and early 1980s. In 1984, the Seitz/Eastman Panel of the National Academy of Sciences reviewed U.S. materials science research facilities. One of the recommendations of this panel was that the United States build a reactor-based steady-state source, the Advanced Neutron Source (ANS), at Oak Ridge National Laboratory. Subsequently, R&D activities related to the design of an accelerator-based source assumed a lower priority. The resumption of pulsed-source studies in this country started simultaneously with design activities in Europe aimed at the European Spallation Source (ESS). The European Community funded a workshop in September 1991 to define the parameters of the ESS. Participants in this workshop included both accelerator builders and neutron source users. A consortium of European countries has proposed to build a 5-MW pulsed source, and a feasibility study is currently under way. Soon after the birth of the ESS, a small group at ANL set about bringing themselves up to date on pulsed-source information since 1984 and studied the feasibility of upgrading ANL`s Intense Pulsed Neutron Source (IPNS) to 1 MW by means of a rapidly cycling synchrotron that could be housed, along with its support facilities, in existing buildings. In early 1993, the Kohn panel recommended that (1) design and construction of the ANS should be completed according to the proposed project schedule and (2) development of competitive proposals for cost-effective design and construction of a 1-MW pulsed spallation source should be authorized immediately.

Conducting feasibilities in clinical trials: An investment to ensure a good study

Directory of Open Access Journals (Sweden)

Viraj Rajadhyaksha

2010-01-01

Full Text Available Conducting clinical trial feasibility is one of the first steps in clinical trial conduct. This process includes assessing internal and environmental capacity, alignment of the clinical trial in terms of study design, dose of investigational product, comparator, patient type, with the local environment and assessing potential of conducting clinical trial in a specific country. A robust feasibility also ensures a realistic assessment and capability to conduct the clinical trial. For local affiliates of pharmaceutical organizations, and contract research organizations, this is a precursor to study placement and influences the decision of study placement. This article provides details on different types of feasibilities, information which is to be included and relevance of each. The article also aims to provide practical hands-on suggestions to make feasibilities more realistic and informative.

Conducting feasibilities in clinical trials: an investment to ensure a good study.

Science.gov (United States)

Rajadhyaksha, Viraj

2010-07-01

Conducting clinical trial feasibility is one of the first steps in clinical trial conduct. This process includes assessing internal and environmental capacity, alignment of the clinical trial in terms of study design, dose of investigational product, comparator, patient type, with the local environment and assessing potential of conducting clinical trial in a specific country. A robust feasibility also ensures a realistic assessment and capability to conduct the clinical trial. For local affiliates of pharmaceutical organizations, and contract research organizations, this is a precursor to study placement and influences the decision of study placement. This article provides details on different types of feasibilities, information which is to be included and relevance of each. The article also aims to provide practical hands-on suggestions to make feasibilities more realistic and informative.

The social network and the geo-hydrological information: the CNR IRPI Facebook page as example of communication.

Science.gov (United States)

Fiorucci, Federica; Bianchi, Cinzia; Marchesini, Ivan; Salvati, Paola; Fugnoli, Federico; Guzzetti, Fausto

2014-05-01

Good communication is a fundamental step for the spread of news and knowledge. The effectiveness and persuasiveness of a message is a function of the interaction of characteristics of the audience, the source of the message, and content of the message. Italian Research Institute for the Hydrogeological Protection (CNR-IRPI) has been publishing information on geo-hydrological events using the Internet (http://sici.irpi.cnr.it/, http://webmap.irpi.cnr.it/, http://geomorphology.irpi.cnr.it/, http://polaris.irpi.cnr.it/, http://giida.irpi.cnr.it/, http://events.irpi.cnr.it/ ). Our websites are mainly visited by experts and the information are used for technical purposes. The contents and the interface of the websites are designed for this type of users. Our intention is to increase the type of users, and we are testing the use of social network to catch the wide public's attention. Social networks have emerged as critical factor in information dissemination, search, marketing expertise and influence discovery, and are an important channel for people to share information. Social scientist have long recognized the importance of social networks in the spread of information. Facebook and Twitter are the most widely used social networking services. They make it simpler to communicate with multiple people at one time. Social media may also make it easier for users to monitor activities of people (friends or followers). An official Facebook page of the Italian Research Institute for the Hydrogeological Protection (CNR-IRPI, https://www.facebook.com/CNR.IRPI ), was created and linked to a Twitter account. The purpose of this page is to disseminate information on flood and landslide events and on our research activities, in order to raise awareness of geo-hydrological matters among users. This page publishes news on current or historical landslide and flood events involving the Italian territory, or news from around the world collected on the network. The news are published as

Front Range Forest Health Partnership Phase 1 feasibility study

Energy Technology Data Exchange (ETDEWEB)

Volkin, P

1998-09-01

The Front Range Forest Health Partnership is an alliance of individuals, citizen groups, federal, state, private, and nonprofit organizations that formed to promote forest health restoration and reduce fire risks on Colorado's Front Range. The partnership promotes selective thinning to restore forest health and supports economically feasible end uses for wood waste materials. The Phase I study was initiated to determine the environmental and economic feasibility of using wood wastes from forested and urban areas for the production of fuel-grade ethanol.

Pre-feasibility study template for nZEB pilot projects development

OpenAIRE

Crespo Sánchez, Eva

2015-01-01

This document corresponds to Task 5.2 NZEB pilot projects development, Deliverable 5.2 Basic project conceptual design with feasibility analysis for eight pilot project of the SUSTAINCO project and should present a structure of pre-feasibility studies for eight NZEB projects implementation. It aims to give an overview of how SUSTAINCO project implementation is to be prepared and which technical and financial parameters to concern.

Important considerations for feasibility studies in physical activity research involving persons with multiple sclerosis: a scoping systematic review and case study.

Science.gov (United States)

Learmonth, Yvonne C; Motl, Robert W

2018-01-01

Much research has been undertaken to establish the important benefits of physical activity in persons with multiple sclerosis (MS). There is disagreement regarding the strength of this research, perhaps because the majority of studies on physical activity and its benefits have not undergone initial and systematic feasibility testing. We aim to address the feasibility processes that have been examined within the context of physical activity interventions in MS. A systematic scoping review was conducted based on a literature search of five databases to identify feasibility processes described in preliminary studies of physical activity in MS. We read and extracted methodology from each study based on the following feasibility metrics: process (e.g. recruitment), resource (e.g. monetary costs), management (e.g. personnel time requirements) and scientific outcomes (e.g. clinical/participant reported outcome measures). We illustrate the use of the four feasibility metrics within a randomised controlled trial of a home-based exercise intervention in persons with MS. Twenty-five studies were identified. Resource feasibility (e.g. time and resources) and scientific outcomes feasibility (e.g. clinical outcomes) methodologies were applied and described in many studies; however, these metrics have not been systematically addressed. Metrics related to process feasibility (e.g. recruitment) and management feasibility (e.g. human and data management) are not well described within the literature. Our case study successfully enabled us to address the four feasibility metrics, and we provide new information on management feasibility (i.e. estimate data completeness and estimate data entry) and scientific outcomes feasibility (i.e. determining data collection materials appropriateness). Our review highlights the existing research and provides a case study which assesses important metrics of study feasibility. This review serves as a clarion call for feasibility trials that will

Active Treatment for Idiopathic Adolescent Scoliosis (ACTIvATeS): a feasibility study.

Science.gov (United States)

Williams, Mark A; Heine, Peter J; Williamson, Esther M; Toye, Francine; Dritsaki, Melina; Petrou, Stavros; Crossman, Richard; Lall, Ranjit; Barker, Karen L; Fairbank, Jeremy; Harding, Ian; Gardner, Adrian; Slowther, Anne-Marie; Coulson, Neil; Lamb, Sarah E

2015-07-01

The feasibility of conducting a definitive randomised controlled trial (RCT) evaluating the clinical effectiveness and cost-effectiveness of scoliosis-specific exercises (SSEs) for adolescent idiopathic scoliosis (AIS) is uncertain. The aim of this study was to assess the feasibility of conducting a large, multicentre trial of SSE treatment for patients with AIS, in comparison with standard care, and to refine elements of the study design. The objectives were to (1) update a systematic review of controlled trials evaluating the efficacy of SSE in AIS; (2) survey UK orthopaedic surgeons and physiotherapists to determine current practice, patient populations and equipoise; (3) randomise 50 adolescents to a feasibility trial of either usual care or SSE interventions across a range of sites; (4) develop, document and assess acceptability and adherence of interventions; (5) assess and describe training requirements of physiotherapists; and (6) gain user input in all relevant stages of treatment and protocol design. Multicomponent feasibility study including UK clinician survey, systematic literature review and a randomised feasibility trial. The randomised feasibility study involved four secondary care NHS trusts providing specialist care for patients with AIS. The randomised feasibility study recruited people aged 10-16 years with mild AIS (Cobb angle of physiotherapy SSE programme supported by a home exercise plan. Our choice of intervention was informed by a systematic review of exercise interventions for AIS. The main outcome was feasibility of recruitment to the randomised study. Other elements were to inform choice of outcomes for a definitive trial and included curve severity, quality of life, requirement for surgery/brace, adverse events, psychological symptoms, costs and health utilities. A UK survey of orthopaedic consultants and physiotherapists indicated a wide variation in current provision of exercise therapy through physiotherapy services. It also found

Bond Feasibility Study. Project Identification Committee Report.

Science.gov (United States)

Wichita Public Schools, KS.

A committee, appointed by the Board of Education, was requested to make a comprehensive study of the school building needs of Unified School District No. 259. In an attempt to determine the feasibility of a general bond election to upgrade the public schools, the specific charge to the committee was to evaluate the needs for physical plant…

Ear-EEG from generic earpieces: A feasibility study

DEFF Research Database (Denmark)

Kidmose, Preben; Looney, D; Jochumsen, Lars

2013-01-01

key patient needs (discreet, unobstrusive, user-friendly, robust) and that is low-cost and suitable for off-the-shelf use; thus promising great advantages for healthcare applications. Its feasibility is validated in a comprehensive comparative study with our established prototype, based...

Fast-mixed spectrum reactor interim report initial feasibility study

International Nuclear Information System (INIS)

Fischer, G.J.; Cerbone, R.J.

1979-01-01

The report summarizes the results of an initial four-month feasibility study of the Fast-Mixed Spectrum Reactor (FMSR). Reactor physics, fuel cycle, and thermal-hydraulic analyses were performed on a reference design. These results when coupled to a fuel and materials evaluation performed in cooperation with the Argonne National Laboratory indicate that the FMSR is feasible provided the fuels, cladding, and subassembly ducts can survive a peak fuel burnup of 15 to 20 atom percent heavy metal and peak fluences of 8 x 10 23 (nvt > 0.1 MeV). The results of this short study have also provided a basis for exploring alternative designs requiring significantly lower peak burnup and fluences for their operation

Longitudinal study of the feasibility of using ecological momentary assessment to study teacher stress: Objective and self-reported measures.

Science.gov (United States)

McIntyre, Teresa M; McIntyre, Scott E; Barr, Christopher D; Woodward, Phillip S; Francis, David J; Durand, Angelia C; Mehta, Paras; Kamarck, Thomas W

2016-10-01

There is a lack of comprehensive research on Ecological Momentary Assessment (EMA) feasibility to study occupational stress, especially its long-term sustainability. EMA application in education contexts has also been sparse. This study investigated the feasibility of using EMA to study teacher stress over 2 years using both objective compliance data and a self-reported feasibility survey. It also examined the influence of individual and school factors on EMA feasibility. Participants were 202 sixth through eighth grade teachers from 22 urban middle schools in the southern United States. EMA was implemented via an iPod-based Teacher Stress Diary (TSD). Teachers recorded demands, stress responses, and resources during 12 days (6 waves) over 2 years. Feasibility was assessed via compliance data generated by the TSD (e.g., entry completion) and an EMA Feasibility Survey of self-reported user-friendliness and EMA interference. The results showed high compliance regarding entry and item completion, and completion time, which was sustained over time. User-friendliness was appraised as very high and EMA interference as low. Initial difficulties regarding timing and length of assessments were addressed via EMA method refinement, resulting in improved feasibility. Teachers' ethnicity, age, marital status, grade/course taught, class size, class load, and daily workload impacted feasibility. The results supported the feasibility of using EMA to study work stress longitudinally and the value of continued feasibility monitoring. They also support EMA use to study teacher stress and inform EMA implementation in schools. Some teacher and school factors need to be taken into consideration when deciding on EMA implementation in education contexts. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Feasibility study on intersection in North Sumatera

Science.gov (United States)

Hastuty, I. P.; Sembiring, I. S.; Anas, R.; Lubis, A. S.

2018-02-01

Traffic congestion is one of the problems faced by big cities, One of them is Binjai city and Medan city in North Sumatera. One of the causes of congestion is intersection of roads with highway and roads with railroads. To ensure the smooth movement of vehicles, technical handling at the intersection is needed. Therefore, it is necessary to pre-study the feasibility of level crossing in Binjai and Medan to be able to assess the investment needs and the level of importance of road development in the region. The development of transportation infrastructure and facilities is based on the thought of improving the transportation network system. The necessity of systemical integrated transportation system handling is needed in creating a transportation efficiency. The purpose of this study is to identify and prioritize the needs of the railway crossings. The objective which we want to be achieved is to obtain a document that contains technical, economic and environmental ability indicators as a reference in the feasibility and planning studies. The methodology used is collecting the primary data, secondary data, introduction of study area as the initial analysis of the problem. From the study it can be concluded that the existence of railway interchange will move the movement through traffic so it will not interfere the movement of traffic within urban areas and it keeps the national road network performance is still good.

International Case-Control Study of Adult Brain, Head and Neck Tumours: Results of the Feasibility Study (invited paper)

International Nuclear Information System (INIS)

Cardis, E.; Kilkenny, M.

1999-01-01

The objectives of the feasibility study were to collect and analyse the information necessary to assess the feasibility of a multi-centric study of adult head and neck tumours (including brain tumours) and mobile telephones. Information was obtained on the availability and accessibility of records from companies, the prevalence of mobile telephone use over time and the expected number of tumour cases in the proposed study regions. The conclusion is that it is feasible to develop a study of the relation between mobile telephone use and brain cancer risk. The feasibility of a study of the relation between radiofrequency exposure and cancer risk is, however, unclear at present. It is unknown whether a sufficiently accurate and precise RF exposure gradient can be derived to classify adequately each subject in the proposed study. A study of the relation between mobile telephone use and risk of salivary gland tumours and acoustic neurinomas is probably feasible, but more information is required about the logistic difficulties of ascertaining these cases in the study regions. Two subcommittees have been formed to develop the exposure measurement and epidemiological aspect of the study. (author)

DPC loading feasibility study report

International Nuclear Information System (INIS)

Dafoe, R.E.; Lopez, D.A.; Williams, K.L.

1997-11-01

Disposal of radioactive wastes now stored at the Idaho Chemical Processing Plant at the Idaho National Engineering and Environmental Laboratory is mandated under a ''Settlement Agreement'' between the Department of Energy and the State of Idaho. This study investigates the feasibility of using the Dry Transfer Cell facility to package waste into Dual Purpose Canisters for interim storage at the adjacent Dry Storage System comprised of an interim storage pad with NUHOMS reg-sign storage modules. The wastes would then be road-ready for eventual disposal in a permanent repository. The operating period for these activities is expected to be from 2015 to 2035

Training Endogenous Task Shifting Using Music Therapy: A Feasibility Study.

Science.gov (United States)

Lynch, Colleen; LaGasse, A Blythe

2016-01-01

People with acquired brain injury (ABI) are highly susceptible to disturbances in executive functioning (EF), and these effects are pervasive. Research studies using music therapy for cognitive improvement in this population are limited. The purpose of this study was to determine the feasibility of a Musical Executive Function Training (MEFT) intervention to address task-shifting skills in adults with ABI and to obtain preliminary evidence of intervention effect on task shifting. Fourteen participants were randomly assigned to one of three groups: a music therapy intervention group (MTG), a singing group (SG), or the no-intervention control group (CG). The SG and MTG met for one hour a day for five days. Feasibility measures included participant completion rates and intervention fidelity. Potential benefits were measured using the Trail Making Test and the Paced Auditory Serial Addition Task as a pre- and posttest measure. Participant completion rates and interventionist fidelity to the protocol supported feasibility. One-way ANOVA of the pre- and posttest group differences revealed a trend toward improvement in the MTG over the SG. Feasibility and effect size data support a larger trial of the MEFT protocol. © the American Music Therapy Association 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

The feasibility study on commercialized fast reactor cycle system

International Nuclear Information System (INIS)

Noda, Hiroshi

2002-01-01

The feasibility study on commercialized Fast Reactor cycle system (FS) has been carried out by a joint team with the participation of all parties concerned in Japan since July, 1999. It aims to clarify various perspectives for commercialized fast reactor cycle system and also suggest development strategies to diverse social needs in the 21 st century. The FS consists of several phases. The phase 1 has progressed as planned and the highly feasible candidate concepts with innovative technologies have been screened out among a wide variety of concepts. During the phase 2, approximately five years after the phase 1, the in-depth design studies and engineering scale tests of key technologies are being conducted to verify and validate the feasibility of screened candidate concepts. At the end of the phase 2, a few promising concepts will be selected with their R and D tasks. The paper describes the results of the phase 1, the activities of the phase 2 and the new concept related to the fast reactor fuel cycle focusing on the reduction in environmental burden, which is one of key factors to sustain the nuclear power generation in the 21 st century

A feasibility study of thyroid cancer among patients treated with I-131

International Nuclear Information System (INIS)

Anderson, T.W.

1984-04-01

This study examined the feasibility of conducting a Canada-wide follow-up study of persons receiving I-131 before 1970, to see if current estimates of induction of thyroid cancer are well founded. It is concluded that such a study is not feasible due to the widespread destruction of old records, and the limited quantity of personal identifying information on those records that do still exist

Feasibility study for private-sector treatment services for alpha-contaminated low-level mixed wastes

International Nuclear Information System (INIS)

Bloom, R.R.; Rodriguez, R.R.

1995-01-01

Rust Federal Services, under contract to the United States Department of Energy (DOE), Idaho Operations Office, performed a study to develop and evaluate the feasibility of a suggested private sector solution for the treatment of alpha-contaminated low-level mixed waste (ALLMW) stored or produced at the Idaho National Engineering Laboratory (INEL). The feasibility study is an initial step in the potential procurement of privatized treatment services for these wastes. Rust's derived objective of the feasibility study was to define an optimal treatment system and analyze the feasibility of that system for accomplishing the processing objectives specified by DOE. All aspects of the selected treatment system were addressed in the feasibility study, including technical, regulatory, public involvement, and financial considerations. Two central elements of the study were a technology screening task to select the optimal treatment system and an analysis of the institutional, business, financial, and contractual issues that are likely to accompany the privatization of treatment services for DOE

Deschutes estuary feasibility study: hydrodynamics and sediment transport modeling

Science.gov (United States)

George, Douglas A.; Gelfenbaum, Guy; Lesser, Giles; Stevens, Andrew W.

2006-01-01

Continual sediment accumulation in Capitol Lake since the damming of the Deschutes River in 1951 has altered the initial morphology of the basin. As part of the Deschutes River Estuary Feasibility Study (DEFS), the United States Geological Survey (USGS) was tasked to model how tidal and storm processes will influence the river, lake and lower Budd Inlet should estuary restoration occur. Understanding these mechanisms will assist in developing a scientifically sound assessment on the feasibility of restoring the estuary. The goals of the DEFS are as follows. - Increase understanding of the estuary alternative to the same level as managing the lake environment.

Feasibility study of component risk ranking for plant maintenance

International Nuclear Information System (INIS)

Ushijima, Koji; Yonebayashi, Kenji; Narumiya, Yoshiyuki; Sakata, Kaoru; Kumano, Tetsuji

1999-01-01

Nuclear power is the base load electricity source in Japan, and reduction of operation and maintenance cost maintaining or improving plant safety is one of the major issues. Recently, Risk Informed Management (RIM) is focused as a solution. In this paper, the outline regarding feasibility study of component risk ranking for plant maintenance for a typical Japanese PWR plant is described. A feasibility study of component risk raking for plant maintenance optimization is performed on check valves and motor-operated valves. Risk ranking is performed in two steps using probabilistic analysis (quantitative method) for risk ranking of components, and deterministic examination (qualitative method) for component review. In this study, plant components are ranked from the viewpoint of plant safety / reliability, and the applicability for maintenance is assessed. As a result, distribution of maintenance resources using risk ranking is considered effective. (author)

A Feasibility Study of Youth Apprenticeship in Arkansas.

Science.gov (United States)

Jobs for the Future, Inc., West Somerville, MA.

A study assessed the feasibility and attractiveness of youth apprenticeship in Arkansas in over 80 interviews with employers in 5 key Arkansas industries and occupations. They were allied health, food processing (equipment repair and maintenance and lab technician/quality control), information services, metalworking, and self-employment and…

Mindfulness and Climate Change Action: A Feasibility Study

Directory of Open Access Journals (Sweden)

Maggie Grabow

2018-05-01

Full Text Available Pro-environmental behaviors and the cultural shifts that can accompany these may offer solutions to the consequences of a changing climate. Mindfulness has been proposed as a strategy to initiate these types of behaviors. In 2017, we pilot-tested Mindful Climate Action (MCA, an eight-week adult education program that delivers energy use, climate change, and sustainability content in combination with training in mindfulness meditation, among 16 individuals living in Madison, WI. We collected participant data at baseline and at different times across the study period regarding household energy use, transportation, diet, and health and happiness. This pilot study aimed to evaluate the feasibility of the various MCA study practices including measurement tools, outcome assessment, curriculum and related educational materials, and especially the mindfulness-based climate action trainings. MCA was well-received by participants as evidenced by high adherence rate, high measures of participant satisfaction, and high participant response rate for surveys. In addition, we successfully demonstrated feasibility of the MCA program, and have estimated participant’s individual carbon footprints related to diet, transportation, and household energy.

Technical Analysis Feasibility Study on Smart Microgrid System in Sekolah Tinggi Teknik PLN

Science.gov (United States)

Suyanto, Heri

2018-02-01

Nowadays application of new and renewable energy as main resource of power plant has greatly increased. High penetration of renewable energy into the grid will influence the quality and reliability of the electricity system, due to the intermittent characteristic of new and renewable energy resources. Smart grid or microgrid technology has the ability to deal with this intermittent characteristic especially if these renewable energy resources integrated to grid in large scale, so it can improve the reliability and efficiency of the grid. We plan to implement smart microgrid system at Sekolah Tinggi Teknik PLN as a pilot project. Before the pilot project start, the feasibility study must be conducted. In this feasibility study, the renewable energy resources and load characteristic at the site will be measured. Then the technical aspect of this feasibility study will be analyzed. This paper explains that analysis of ths feasibility study.

Methodology study: Co-generation feasibility at sawmills

International Nuclear Information System (INIS)

Host, J.

1991-01-01

This report discussed the various factors that should be studied and evaluated before establishing a cogeneration plant. The results of three case studies and a survey of energy needs in smaller and medium size sawmills are also presented. In general, cogeneration is feasible for supplying electric energy required for processing logs using fuelbark and other residues from the manufacturing process. A rebuilt turbine-generator unit is an initial cost saving alternative that is advantageous throughout the life of the operation

Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

Directory of Open Access Journals (Sweden)

Sandra M Eldridge

Full Text Available We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

Defining Feasibility and Pilot Studies in Preparation for Randomised Controlled Trials: Development of a Conceptual Framework.

Science.gov (United States)

Eldridge, Sandra M; Lancaster, Gillian A; Campbell, Michael J; Thabane, Lehana; Hopewell, Sally; Coleman, Claire L; Bond, Christine M

2016-01-01

We describe a framework for defining pilot and feasibility studies focusing on studies conducted in preparation for a randomised controlled trial. To develop the framework, we undertook a Delphi survey; ran an open meeting at a trial methodology conference; conducted a review of definitions outside the health research context; consulted experts at an international consensus meeting; and reviewed 27 empirical pilot or feasibility studies. We initially adopted mutually exclusive definitions of pilot and feasibility studies. However, some Delphi survey respondents and the majority of open meeting attendees disagreed with the idea of mutually exclusive definitions. Their viewpoint was supported by definitions outside the health research context, the use of the terms 'pilot' and 'feasibility' in the literature, and participants at the international consensus meeting. In our framework, pilot studies are a subset of feasibility studies, rather than the two being mutually exclusive. A feasibility study asks whether something can be done, should we proceed with it, and if so, how. A pilot study asks the same questions but also has a specific design feature: in a pilot study a future study, or part of a future study, is conducted on a smaller scale. We suggest that to facilitate their identification, these studies should be clearly identified using the terms 'feasibility' or 'pilot' as appropriate. This should include feasibility studies that are largely qualitative; we found these difficult to identify in electronic searches because researchers rarely used the term 'feasibility' in the title or abstract of such studies. Investigators should also report appropriate objectives and methods related to feasibility; and give clear confirmation that their study is in preparation for a future randomised controlled trial designed to assess the effect of an intervention.

Feasibility studies - Oesthammar, Nykoeping, Oskarshamn, Tierp, Hultsfred and Aelvkarleby. Summary report

International Nuclear Information System (INIS)

2001-06-01

Swedish Nuclear Fuel and Waste Management Company, SKB, has carried out feasibility studies on a municipal scale as a part of the siting programme for the deep repository for spent nuclear fuel. Final reports describing the results of the six feasibility studies in Oesthammar, Nykoeping, Oskarshamn, Tierp, Aelvkarleby and Hultsfred were submitted during the autumn and winter of 2000/2001. With this as a basis, the siting work can now proceed to the next phase - site investigations. In this stage, investigations that include test drilling will be conducted on at least two sites. In December 2000, SKB published the report 'Integrated account of method, site selection and programme prior to the site investigation phase', in which SKB stipulates where they want to conduct site investigations and how they will be carried out. The report is being reviewed by the Swedish Nuclear Power Inspectorate during the first half of 2001. Before the site investigations can be initiated,the go-ahead is required from the national safety authorities, the Government, and concerned municipalities and landowners. SKB projects that the it will be possible to commence the site investigations in 2002. This report comprises an English summary of the final reports from the six feasibility studies. The report summarizes the most important results and conclusions from the different feasibility studies. All six final reports are available in their entirety in Swedish

Feasibility studies - Oesthammar, Nykoeping, Oskarshamn, Tierp, Hultsfred and Aelvkarleby. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

Swedish Nuclear Fuel and Waste Management Company, SKB, has carried out feasibility studies on a municipal scale as a part of the siting programme for the deep repository for spent nuclear fuel. Final reports describing the results of the six feasibility studies in Oesthammar, Nykoeping, Oskarshamn, Tierp, Aelvkarleby and Hultsfred were submitted during the autumn and winter of 2000/2001. With this as a basis, the siting work can now proceed to the next phase - site investigations. In this stage, investigations that include test drilling will be conducted on at least two sites. In December 2000, SKB published the report 'Integrated account of method, site selection and programme prior to the site investigation phase', in which SKB stipulates where they want to conduct site investigations and how they will be carried out. The report is being reviewed by the Swedish Nuclear Power Inspectorate during the first half of 2001. Before the site investigations can be initiated,the go-ahead is required from the national safety authorities, the Government, and concerned municipalities and landowners. SKB projects that the it will be possible to commence the site investigations in 2002. This report comprises an English summary of the final reports from the six feasibility studies. The report summarizes the most important results and conclusions from the different feasibility studies. All six final reports are available in their entirety in Swedish.

Pre-feasibility study of 80mw onshore wind farm

International Nuclear Information System (INIS)

Almas, M.S.

2014-01-01

This paper discusses a pre-feasibility study of 80MW onshore wind farm in the KPK (Khyber Pakhtunkhwa) province previously known as NWFP (North West Frontier) Province of Pakistan. The realistic data of wind speed is collected from Laboratory of Meteorology and Climatology (University of the Punjab) to study the feasibility of wind farm. Detailed analysis of wind turbines from four different manufacturers is carried out together with justifications of selecting a particular wind turbine. Issues related to site selection, wind farm civil foundation, recommendations for a particular choice of tower along with environmental effects are presented. Wind data analysis is carried out by using WINDROSE PRO software to determine the resultant direction of wind at the selected site for wind farm layout. The wind distribution at hub height of the wind turbine is calculated and is used to compute annual power production by the wind farm using power curves of the wind turbine. Electrical network integration issues of wind farm to the external grid are studied and the optimum point of connection is proposed. Finally, economic analysis of the whole wind farm project depending upon the LCC (Life Cycle Cost Analysis) is presented and the feasibility of the project from the investor's point of view is identified. The study concludes that the cost per kilowatt hour of electricity generated by this wind power plant will be 10.4 PKR/kWh and the payback period for the whole project is about 11.2 years. (author)

Staging and storage facility feasibility study. Final report

International Nuclear Information System (INIS)

Swenson, C.E.

1995-02-01

This study was performed to investigate the feasibility of adapting the design of the HWVP Canister Storage Building (CSB) to meet the needs of the WHC Spent Nuclear Fuel Project for Staging and Storage Facility (SSF), and to develop Rough Order of Magnitude (ROM) cost and schedule estimates

Geology and geohydrology of the East Texas Basin. A report on the progress of nuclear waste isolation feasibility studies (1980)

International Nuclear Information System (INIS)

Kreitler, C.W.; Collins, E.W.; Davidson, E.D. Jr.

1981-01-01

The third year of research was highlighted by the integration of regional basinal studies with growth histories for specific domes, studies of cap-rock diagenesis and salt deformation, preliminary studies of ground-water flow and geochemistry around Oakwood Dome, and preliminary studies of microseismicity in the Mount Enterprise fault zone. 119 figures, 15 tables

Feasibility study: Assess the feasibility of siting a monitored retrievable storage facility. Phase 1

Energy Technology Data Exchange (ETDEWEB)

King, J.W.

1993-08-01

The purpose of phase one of this study are: To understand the waste management system and a monitored retrievable storage facility; and to determine whether the applicant has real interest in pursuing the feasibility assessment process. Contents of this report are: Generating electric power; facts about exposure to radiation; handling storage, and transportation techniques; description of a proposed monitored retrievable storage facility; and benefits to be received by host jurisdiction.

Feasibility study of full-reactor gas core demonstration test

Science.gov (United States)

Kunze, J. F.; Lofthouse, J. H.; Shaffer, C. J.; Macbeth, P. J.

1973-01-01

Separate studies of nuclear criticality, flow patterns, and thermodynamics for the gas core reactor concept have all given positive indications of its feasibility. However, before serious design for a full scale gas core application can be made, feasibility must be shown for operation with full interaction of the nuclear, thermal, and hydraulic effects. A minimum sized, and hence minimum expense, test arrangement is considered for a full gas core configuration. It is shown that the hydrogen coolant scattering effects dominate the nuclear considerations at elevated temperatures. A cavity diameter of somewhat larger than 4 ft (122 cm) will be needed if temperatures high enough to vaporize uranium are to be achieved.

Feasibility Study and Optimization of An Hybrid System (Eolian ...

African Journals Online (AJOL)

Feasibility Study and Optimization of An Hybrid System (Eolian- Photovoltaic - Diesel) With Provision of Electric Energy Completely Independent. ... reducing emissions of greenhouse gas (CO2 rate = 16086 kg / year for a system using only the generator diesel and is 599 kg / year for the stand alone hybrid system studied).

Engineering management at feasibility study stage of nuclear power plant under EPC mode

International Nuclear Information System (INIS)

Wang Zhiqiang

2015-01-01

After the investment reform by the State Council in 2004, NDRC carries out approval system for enterprises to invest in nuclear power plants. Feasibility study stage is a critical stage on the mainline of nuclear power project approval, which intersects with the license application, and engineering design. The owners of nuclear power plants are required stringently in engineering management. From the owners' management point of view under EPC mode, this paper sorts the preliminary project process for nuclear power plants, focusing on the management in the feasibility study stage. License application and engineering design management in the feasibility study stage are also discussed. (author)

Feasibility Study on Solar District Heating in China

DEFF Research Database (Denmark)

Huang, Junpeng; Fan, Jianhua; Furbo, Simon

This paper analyzes the feasibility of developing solar district heating (SDH) in China from the perspective of incentive policy, selections of technical route, regional adaptability and economic feasibility for clean heating. Based on the analyzation, this proposes a road map for the development...

[Cambridge Conference on School Mathematics Feasibility Studies 9-13.

Science.gov (United States)

Cambridge Conference on School Mathematics, Newton, MA.

These materials are a part of a series of studies sponsored by the Cambridge Conference on School Mathematics which reflects the ideas of CCSM regarding the goals and objectives for school mathematics K-12. Feasibility Studies 9-13 contain a wide range of topics. The following are the titles and brief descriptions of these studies. Number…

Geohydrology of the Keechi, Mount Sylvan, Oakwood, and Palestine salt domes in the northeast Texas salt-dome basin

International Nuclear Information System (INIS)

Carr, J.E.; Halasz, S.J.; Peters, H.B.

1980-01-01

The salt within these domes has penetrated as much as 20,000 feet of Mesozoic and Cenozoic strata, and presently extends to within 120 to 800 feet of the land surface. The salt penetrates or closely underlies major freshwater and salinewater aquifers within the basin. To provide a safe repository for radioactive wastes within one or more of these domes, a thorough understanding of the geohydrology needs to be obtained, and the hydrologic stability of the domes needs to be established for the expected life of the storage facility. Dissolution may exist at all four candidate salt domes, possibly through contact with Cretaceous or Tertiary aquifers, or through fault systems in the vicinity of the domes. Strata overlying and surrounding Palestine and Keechi Salt Domes have been arched into steeply-dipping folds that are complexly faulted. Similar conditions exist at Oakwood and Mount Sylvan Domes, except that the Tertiary strata have been only moderately disturbed. Additional problems concerning the hydrologic stability of Oakwood and Palestine Salt Domes have resulted from the disposal of oil-field salinewater in the cap rock at the Oakwood Dome and previous solution mining of salt at the Palestine Dome

Space shuttle/food system study. Package feasibility study, modifications 3S, 4C and 5S

Science.gov (United States)

1974-01-01

An optimum feeding system for the space shuttle was presented. This system consisted of all rehydratable type foods which were enclosed in a 4 in. x 4 in. x 1 in. flexible package. A feasibility follow-on study was conducted, and two acceptable, feasible prototypes for this package are described.

Whose Frames Mattered? The Feasibility Study in the Municipality of Tierp 1998-2000

International Nuclear Information System (INIS)

Johansson, Hanna Sofia

2003-01-01

In December 2001 SKB (the Swedish Nuclear Fuel and Waste Management Co) presented a ranking list of the eight feasibility studies carried out in Sweden. The feasibility study in Tierp was cited as showing that potentially good bedrock could be found in the municipality and SKB therefore asked to carry out a site investigation. Tierp is a neighbouring municipality to Oesthammar, a municipality that hosts nuclear power plants, with around 20,000 inhabitants and an area of 1543 km 2 . This paper focuses on why the Municipal Council in Tierp voted 'no' to further investigations even though SKB pointed out the municipality as having potentially good bedrock. In 1998 a feasibility study in Tierp was started. The arguments presented for a feasibility study were: the proximity to Forsmark nuclear power plant in Oesthammar, responsibilities for future generations, and that an investigation of the municipality could be used for other purposes. The main question this paper asks is the following: why did the Municipal Council in Tierp say 'no' to further investigations? This question is of interest since SKB claimed that Tierp had potentially good bedrock. The hypothesis is that the democratic models (representative democracy, discursive democracy or technocracy) present in the feasibility study and the boundary work carried out, i.e. how the boundary between science and politics was drawn, and which actors had access to the discussion on the public agenda, influenced the decision of the Council. The main sources used are interviews and a Swedish governmental investigation report about the feasibility studies. Twelve fairly open interviews with actors from the municipal organization, SKB, local opinion groups and the media were carried out. The questions cover how hey worked with the study, how the municipality organized its work, how they defined the nuclear waste issues and how they tried to communicate their views to other actors

Pre-Feasibility Study of 80MW Onshore Wind Farm

Directory of Open Access Journals (Sweden)

Muhammad Shoaib Almas

2014-10-01

Full Text Available This paper discusses a pre-feasibility study of 80MW onshore wind farm in the KPK (Khyber Pakhtunkhwa province previously known as NWFP (North West Frontier Province of Pakistan. The realistic data of wind speed is collected from Laboratory of Meteorology & Climatology (University of the Punjab to study the feasibility of wind farm. Detailed analysis of wind turbines from four different manufacturers is carried out together with justifications of selecting a particular wind turbine. Issues related to site selection, wind farm civil foundation, recommendations for a particular choice of tower along with environmental effects are presented. Wind data analysis is carried out by using WINDROSE PRO software to determine the resultant direction of wind at the selected site for wind farm layout. The wind distribution at hub height of the wind turbine is calculated and is used to compute annual power production by the wind farm using power curves of the wind turbine. Electrical network integration issues of wind farm to the external grid are studied and the optimum point of connection is proposed. Finally, economic analysis of the whole wind farm project depending upon the LCC (Life Cycle Cost Analysis is presented and the feasibility of the project from the investor?s point of view is identified. The study concludes that the cost per kilowatt hour of electricity generated by this wind power plant will be 10.4 PKR/kWh and the payback period for the whole project is about 11.2 years

How to Train an Injured Brain? A Pilot Feasibility Study of Home-Based Computerized Cognitive Training.

Science.gov (United States)

Verhelst, Helena; Vander Linden, Catharine; Vingerhoets, Guy; Caeyenberghs, Karen

2017-02-01

Computerized cognitive training programs have previously shown to be effective in improving cognitive abilities in patients suffering from traumatic brain injury (TBI). These studies often focused on a single cognitive function or required expensive hardware, making it difficult to be used in a home-based environment. This pilot feasibility study aimed to evaluate the feasibility of a newly developed, home-based, computerized cognitive training program for adolescents who suffered from TBI. Additionally, feasibility of study design, procedures, and measurements were examined. Case series, longitudinal, pilot, feasibility intervention study with one baseline and two follow-up assessments. Nine feasibility outcome measures and criteria for success were defined, including accessibility, training motivation/user experience, technical smoothness, training compliance, participation willingness, participation rates, loss to follow-up, assessment timescale, and assessment procedures. Five adolescent patients (four boys, mean age = 16 years 7 months, standard deviation = 9 months) with moderate to severe TBI in the chronic stage were recruited and received 8 weeks of cognitive training with BrainGames. Effect sizes (Cohen's d) were calculated to determine possible training-related effects. The new cognitive training intervention, BrainGames, and study design and procedures proved to be feasible; all nine feasibility outcome criteria were met during this pilot feasibility study. Estimates of effect sizes showed small to very large effects on cognitive measures and questionnaires, which were retained after 6 months. Our pilot study shows that a longitudinal intervention study comprising our novel, computerized cognitive training program and two follow-up assessments is feasible in adolescents suffering from TBI in the chronic stage. Future studies with larger sample sizes will evaluate training-related effects on cognitive functions and underlying brain structures.

The Use of Market Feasibility Studies in the Restaurant Industry for Small and Medium-sized Restaurants

OpenAIRE

Kolster, Maria

2017-01-01

The goals of this thesis are to provide the reader with new information about market feasibility studies in the restaurant industry and to design a market feasibility template for the international restaurant industry which can be used for small and medium-sized restaurants before entering the market. The objectives are to define the ideal factors of a market feasibility study for the international restaurant industry, to learn and become an expert in feasibility studies for the restaurant i...

Municipal management and geo-hydrological aspects of importance in the potable water supply of Lindley

Directory of Open Access Journals (Sweden)

Eric Nealer

2014-07-01

Full Text Available When the South African Government in 1998 re-demarcated its 283 municipalities so that they completely cover the country in a “wall-to-wall” manner, their main focus was on growing local economies and maintaining the provision of an increased number of diverse and more complex basic municipal services to new geographical areas consisting of millions of citizens who might previously had been neglected. In most of the instances the newly established and merged municipalities were demarcated according to geographical aspects inherited from the previous political dispensation, historical municipal areas and magisterial district farm names. The fact that these municipal government jurisdictions for the purpose of improving co-operative municipal- and integrated water resources management (IWRM, in most instances do not correspond with environmental and physical land features such as the demarcated surface water (rivers drainage regions’ boundaries, could lead to the ineffective, inefficient and non-economic municipal management of water, sanitation and environmental services. The aforementioned is a case with reference to water services management in the Free State Province town of Lindley located in the Vals River catchment and the Nketoana Local Municipality’s area of jurisdiction. An extensive literature review, the use and study of geographic tools such as maps, ortho- photos and information data bases, as well as two field visits to the area, enabled the researchers to identify the essential geographical, geo-hydrological and municipal management aspects of importance for the potable water service providers and managers in the Lindley municipal area. The researchers argue that effective trans-boundary municipal management through simunye-type co-operative governance and IWRM must be facilitated in the Vals River surface water catchment between the respective local- and district municipalities for the benefit of the Lindley, Arlington

Feasibility study on production of Co-60 in PHWR

Energy Technology Data Exchange (ETDEWEB)

Park, Kyung Bae; Han, Hyon Soo; Joo, Po Kook

2000-05-01

The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ceiling hoist system. At present, storage pool has got admission based on 400 kCi. But it is necessary to seismic analysis and design improvement of shielding to store 10 MCi (Co-60) which is the estimated Co-60 capacity produced by 3 PHWRs. According to present investigation, a production of Co-60 by PHWR and RIPE was seemed to be an economically feasible business and it was also expected that a joint venture will be able to realize by cooperation with MDS Nordion Co.

Feasibility study on production of Co-60 in PHWR

International Nuclear Information System (INIS)

Park, Kyung Bae; Han, Hyon Soo; Joo, Po Kook

2000-05-01

The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ceiling hoist system. At present, storage pool has got admission based on 400 kCi. But it is necessary to seismic analysis and design improvement of shielding to store 10 MCi (Co-60) which is the estimated Co-60 capacity produced by 3 PHWRs. According to present investigation, a production of Co-60 by PHWR and RIPE was seemed to be an economically feasible business and it was also expected that a joint venture will be able to realize by cooperation with MDS Nordion Co

Feasibility study of structured diagnosis methods for functional dyspepsia in Korean medicine clinics

Directory of Open Access Journals (Sweden)

Jeong Hwan Park

2017-12-01

Full Text Available Background: Functional dyspepsia (FD is the seventh most common disease encountered in Korean medicine (KM clinics. Despite the large number of FD patients visiting KM clinics, the accumulated medical records have no utility in evidence development, due to being unstructured. This study aimed to construct a standard operating procedure (SOP with appropriate structured diagnostic methods for FD, and assess the feasibility for use in KM clinics. Methods: Two rounds of professional surveys were conducted by 10 Korean internal medicine professors to select the representative diagnostic methods. A feasibility study was conducted to evaluate compliance and time required for using the structured diagnostic methods by three specialists in two hospitals. Results: As per the results of the professional survey, five questionnaires and one basic diagnostic method were selected. An SOP was constructed based on the survey results, and a feasibility study showed that the SOP compliance score (out of 5 was 3.45 among the subjects, and 3.25 among the practitioners. The SOP was acceptable and was not deemed difficult to execute. The total execution time was 136.5 minutes, out of which the gastric emptying test time was 129 minutes. Conclusion: This feasibility study of the SOP with structured diagnostic methods for FD confirmed it was adequate for use in KM clinics. It is expected that these study findings will be helpful to clinicians who wish to conduct observational studies as well as to generate quantitative medical records to facilitate Big Data research. Keywords: Big Data, Dyspepsia, Korean medicine, Feasibility studies, Observational study

Feasibility study of gasification of oil palm fronds

Directory of Open Access Journals (Sweden)

S.A. Sulaiman

2015-12-01

Full Text Available Considering the large and consistent supply, oil palm fronds could be a promising source of biomass energy through gasification. There is very scarce information on the characteristics of oil palm fronds, which is vital in deciding if such biomass is technically suitable for gasification. In the present work, the feasibility of oil palm fronds for biomass gasification is studied. The study is conducted experimentally via standard tests to determine their thermochemical characteristics. Ultimate analysis is conducted to determine the contents of carbon, nitrogen, hydrogen and sulphide in oil palm fronds. Proximate analysis is performed to identify the burning characteristics of the biomass. The energy content in the fronds is determined by using a bomb calorie meter and is around 18 MJ/kg. The ignitability of the fronds is also studied experimentally to assess the ease to start-up combustion of the fronds. The characteristics of the flame of the resulting syngas from gasification of oil palm fronds are qualitatively studied. Simulated syngas composition study reveals potentials of 22% CO, 1.3% H2, 18.5% CO2 and traces of CH4. The study is extended to computer simulation to predict composition of the syngas. It is found from this work that oil palm fronds are feasible for gasification and has a good potential as a renewable energy source.

Optical Coherence Tomography of the Breast: A Feasibility Study

National Research Council Canada - National Science Library

Connolly, James

2003-01-01

.... This novel imaging technology has the potential to improve cancer detection and diagnosis. The aim of this study was to determine the feasibility of applying OCT imaging to normal and pathologic human breast tissue, as well as other human tissues...

Optical Coherence Tomography of the Breast: A Feasibility Study

National Research Council Canada - National Science Library

Connolly, James L

2005-01-01

.... This novel imaging technology has the potential to improve cancer detection and diagnosis. The aim of this study was to determine the feasibility of applying OCT imaging to normal and pathologic human breast tissue, as well as other human tissues...

Depleted uranium concrete container feasibility study

International Nuclear Information System (INIS)

Haelsig, R.T.

1994-09-01

The purpose of this report is to consider the feasibility of using containers constructed of depleted uranium aggregate concrete (DUCRETE) to store and transport radioactive materials. The method for this study was to review the advantages and disadvantages of DUCRETE containers considering design requirements for potential applications. The author found that DUCRETE is a promising material for onsite storage containers, provided DUCRETE vessels can be certified for one-way transport to disposal sites. The author also found that DUCRETE multipurpose spent nuclear fuel storage/transport packages are technically viable, provided altered temperature acceptance limits can be developed for DUCRETE

Computer-Based Job and Occupational Data Collection Methods: Feasibility Study

National Research Council Canada - National Science Library

Mitchell, Judith I

1998-01-01

.... The feasibility study was conducted to assess the operational and logistical problems involved with the development, implementation, and evaluation of computer-based job and occupational data collection methods...

Construction monitoring constraints and challenges:A feasibility study

OpenAIRE

Fidler, Paul; Vardanega, Paul J; Long, Peter; Webb, Graham; Stehle, John; Middleton, Campbell

2013-01-01

This paper presents a study of the constraints and challenges faced by the authors when invited to study the feasibility of developing a monitoring system to provide specific information sought by the designer and contractor during the construction of the new 225m high, 48 storey steel-framed Leadenhall Building, located at 122 Leadenhall Street in London. The original goal of the study was to develop a system to assist with the active alignment of the building during construction, a key aim ...

Full system decontamination feasibility studies

International Nuclear Information System (INIS)

Denault, R.P.; LeSurf, J.E.; Walschot, F.W.

1988-01-01

Many chemical decontaminations have been performed on subsystems in light water reactors (BWRs and PWRs) but none on the full system (including the fuel) of large, (>500 MWe) investor owned reactors. Full system decontaminations on pressure-tubed reactors have been shown to facilitate maintenance, inspection, repair and replacement of reactor components. Further advantages are increased reactor availability and plant life extension. A conceptual study has been performed for EPRI (for PWRs) and Commonwealth Edison Co (for BWRs) into the applicability and cost benefit of full system decontaminations (FSD). The joint study showed that FSDs in both PWRs and BWRs, with or without the fuel included in the decontamination, are feasible and cost beneficial provided a large amount of work is to be done following the decontamination. The large amounts of radioactive waste generated can be managed using current technologies. Considerable improvements in waste handling, and consequent cost savings, can be obtained if new techniques which are now reaching commercial application are used. (author)

Lunar Wireless Power Transfer Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Freid, Sheldon [National Security Technologies, LLC. (NSTec), Mercury, NV (United States); Popovic, Zoya [Univ. of Colorado, Boulder, CO (United States); Beckett, David R. [Independent Consultant; Anderson, Scott R. [Independent Consultant; Mann, Diana [Independent Consultant; Walker, Stuart [Independent Consultant

2008-03-01

This study examines the feasibility of a multi-kilowatt wireless radio frequency (RF) power system to transfer power between lunar base facilities. Initial analyses, show that wireless power transfer (WPT) systems can be more efficient and less expensive than traditional wired approaches for certain lunar and terrestrial applications. The study includes evaluations of the fundamental limitations of lunar WPT systems, the interrelationships of possible operational parameters, and a baseline design approach for a notionial system that could be used in the near future to power remote facilities at a lunar base. Our notional system includes state-of-the-art photovoltaics (PVs), high-efficiency microwave transmitters, low-mass large-aperture high-power transmit antennas, high-efficiency large-area rectenna receiving arrays, and reconfigurable DC combining circuitry.

Feasibility Study of Renewable Energy in Singapore

OpenAIRE

King, Sebastian; Wettergren, Per

2011-01-01

Singapore is a country that is currently highly dependent on import of oil and gas. In order to be able to shift into a more sustainable energy system, Singapore is investing in research regarding different technologies and systems so as to establish more sustainable energy solutions. Seeing how air-conditioning accounts for approximately 30 % of Singapore’s total energy consumption, a feasibility study is being conducted on whether an integrated system using a thermally active building syste...

Computing with words to feasibility study of software projects

Directory of Open Access Journals (Sweden)

Marieta Peña Abreu

2017-02-01

Full Text Available Objective: This paper proposes a method to analyze the technical, commercial and social feasibility of software projects in environments of uncertainty. It allows working with multiple experts and multiple criteria and facilitates decision-making. Method: The proposal contains two phases, first the necessary information is collected and in second place projects are evaluated using 2-tuple linguistic representation model. The experts are selected by analyzing their curricular synthesis. The evaluation criteria are defined using the technique Focus Group and weighted in the interval (0,1 according to their importance. three domains are offered to express the preferences: numeric, interval-valued and linguistic. For aggregation extended arithmetic mean and weighted average extended are used, preventing the loss of information. A 2-tuple (feasibility, precision is obtained as a result for each project. Results: The evaluation of P1 project was a very high feasibility with -0,33 of precision. The P2 project obtained a high feasibility with 0,38 of precision and P3 project achieved a medium feasibility with -0,21 of precision. Conclusions: This method is favorable for software projects feasibility analysis with presence of multiple experts and criteria, in environments of uncertainty. It tries heterogeneous assessments without loss of information. Their results are consistent and useful for decision makers.

Morbidity follow-up feasibility study

International Nuclear Information System (INIS)

Carpenter, M.

1988-02-01

The report reviews the available sources of data within Canada for undertaking morbidity follow-up studies to both supplement and complement studies using Canadian mortality data. Such studies would permit earlier detection and more sensitive measures of differences in risk for exposures to radiation and allow timely measures to be taken to minimize any occupational and environmental health risk to radiation workers. The technical feasibility of using these sources was reviewed using the criteria of adequate personal identifying information, automation of data records, file size and the accuracy of the morbidity diagnosis information. At the present time certain of the provincial cancer registry files meet these criteria best. A work plan was prepared suggesting a morbidity pilot study to clarify the role of occupational factors in the incidence of cancer among radiation workers using the Alberta Cancer Registry file and the National Dose Registry (NDR) file of radiation workers. For the longer term a full cohort study using the National Cancer Incidence Reporting System (NCIRS) and the NDR workers as the study population would provide information on all radiation workers on a national basis. A work plan was prepared and some initial format conversion of historical data was undertaken to begin developing the NCIRS into a data base suitable for long-term health studies

Feasible mathematics II

CERN Document Server

Remmel, Jeffrey

1995-01-01

Perspicuity is part of proof. If the process by means of which I get a result were not surveyable, I might indeed make a note that this number is what comes out - but what fact is this supposed to confirm for me? I don't know 'what is supposed to come out' . . . . 1 -L. Wittgenstein A feasible computation uses small resources on an abstract computa­ tion device, such as a 'lUring machine or boolean circuit. Feasible math­ ematics concerns the study of feasible computations, using combinatorics and logic, as well as the study of feasibly presented mathematical structures such as groups, algebras, and so on. This volume contains contributions to feasible mathematics in three areas: computational complexity theory, proof theory and algebra, with substantial overlap between different fields. In computational complexity theory, the polynomial time hierarchy is characterized without the introduction of runtime bounds by the closure of certain initial functions under safe composition, predicative recursion on nota...

Feasibility study of a contained pulsed nuclear propulsion engine

International Nuclear Information System (INIS)

Parlos, A.G.; Metzger, J.D.

1994-01-01

The result of a feasibility analysis of a contained pulsed nuclear propulsion (CPNP) engine concept utilizing the enormously dense energy generated by small nuclear detonations is presented in this article. This concept was initially proposed and studied in the 1950s and 1960s under the program name HELIOS. The current feasibility of the concept is based upon materials technology that has advanced to a state that allows the design of pressure vessels required to contain the blast associated with small nuclear detonations. The impulsive nature of the energy source provides the means for circumventing the materials thermal barriers that are inherent in steady-state nuclear propulsion concepts. The rapid energy transfer to the propellant results in high thrust levels for times less than 1 s following the detonation. The preliminary feasibility analysis using off-the-shelf materials technology appears to indicate that the CPNP concept can have thrust-to-weight ratios on the order of 1 or greater. Though the specific impulse is not a good indicator for impulsive engines, an operating-cycle averaged specific impulse of approximately 1000 or greater seconds was calculated. 16 refs

Aleutian Pribilof Islands Wind Energy Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Bruce A. Wright

2012-03-27

Under this project, the Aleutian Pribilof Islands Association (APIA) conducted wind feasibility studies for Adak, False Pass, Nikolski, Sand Point and St. George. The DOE funds were also be used to continue APIA's role as project coordinator, to expand the communication network quality between all participants and with other wind interest groups in the state and to provide continued education and training opportunities for regional participants. This DOE project began 09/01/2005. We completed the economic and technical feasibility studies for Adak. These were funded by the Alaska Energy Authority. Both wind and hydro appear to be viable renewable energy options for Adak. In False Pass the wind resource is generally good but the site has high turbulence. This would require special care with turbine selection and operations. False Pass may be more suitable for a tidal project. APIA is funded to complete a False Pass tidal feasibility study in 2012. Nikolski has superb potential for wind power development with Class 7 wind power density, moderate wind shear, bi-directional winds and low turbulence. APIA secured nearly $1M from the United States Department of Agriculture Rural Utilities Service Assistance to Rural Communities with Extremely High Energy Costs to install a 65kW wind turbine. The measured average power density and wind speed at Sand Point measured at 20m (66ft), are 424 W/m2 and 6.7 m/s (14.9 mph) respectively. Two 500kW Vestas turbines were installed and when fully integrated in 2012 are expected to provide a cost effective and clean source of electricity, reduce overall diesel fuel consumption estimated at 130,000 gallons/year and decrease air emissions associated with the consumption of diesel fuel. St. George Island has a Class 7 wind resource, which is superior for wind power development. The current strategy, led by Alaska Energy Authority, is to upgrade the St. George electrical distribution system and power plant. Avian studies in Nikolski

Feasibility study on X-ray source with pinhole imaging method

International Nuclear Information System (INIS)

Qiu Rui; Li Junli

2007-01-01

In order to verify the feasibility of study on X-ray source with pinhole imaging method, and optimize the design of X-ray pinhole imaging system, an X-ray pinhole imaging equipment was set up. The change of image due to the change of the position and intensity of X-ray source was estimated with mathematical method and validated with experiment. The results show that the change of the spot position and gray of the spot is linearly related with the change of the position and intensity of X-ray source, so it is feasible to study X-ray source with pinhole imaging method in this application. The results provide some references for the design of X-ray pinhole imaging system. (authors)

Battery energy storage market feasibility study

International Nuclear Information System (INIS)

Kraft, S.; Akhil, A.

1997-07-01

Under the sponsorship of the Department of Energy's Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed energy storage as an important enabling technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1)

Battery energy storage market feasibility study

Energy Technology Data Exchange (ETDEWEB)

Kraft, S. [Frost and Sullivan, Mountain View, CA (United States); Akhil, A. [Sandia National Labs., Albuquerque, NM (United States). Energy Storage Systems Analysis and Development Dept.

1997-07-01

Under the sponsorship of the Department of Energy`s Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed energy storage as an important enabling technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1).

Experiences of a feasibility study of children with albinism in Zimbabwe: a discussion paper.

Science.gov (United States)

Taylor, Julie S; Lund, Patricia

2008-08-01

Feasibility studies are often a helpful prelude to constructing fundable research proposals. Where the intended research is in a foreign country, focuses on a vulnerable population, and is aggravated by political and pragmatic challenges, feasibility studies become essential. Albinism, a genetic condition of reduced melanin synthesis, is a major public health issue in southern Africa. Whilst much is known about the health needs of children with albinism, little is understood about how to address these effectively in low income countries. Further, the child care and protection needs of children with albinism are largely unexplored. Zimbabwe's current political and economic climate presents additional challenges to research on the topic. The technical, economic, legal, collaborative, operational, schedule and political feasibilities (acronym TELCOSP) to undertaking a study on children with albinism in Zimbabwe were explored over a six week period of fieldwork in the country. Using the TELSCOSP framework allowed a deconstruction of each challenge to provide innovative solutions. The economic and legal feasibility aspects presented some difficulties that will require flexibility and perseverance to overcome. With the assistance of the local communities and people with albinism in Zimbabwe, the obstacles appear surmountable. The feasibility study provided a productive framework for addressing potential challenges in studying the needs of Zimbabwe's children living with albinism.

Feasibility study on the thorium fueled boiling water breeder reactor

International Nuclear Information System (INIS)

PetrusTakaki, N.

2012-01-01

The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

Feasibility study on a cosmic-ray level gauge

International Nuclear Information System (INIS)

Matsuda, H.; Fukaya, M.; Minato, S.

1989-01-01

Cosmic-ray intensities were measured at the stairs in a subway station in Nagoya City, inside a tall concrete building and under a cylindrical water tank, to examine the feasibility of a cosmic-ray level gauge. The measured results agreed quite well with the theoretical calculations. These results show that a cosmic-ray level gauge is feasible. (author)

Feasibility studies on cogeneration from industrial wood-processing residues in Ghana

International Nuclear Information System (INIS)

Brew-Hammond, A.; Atakora, S.B.

1999-01-01

Several feasibility studies have been undertaken on cogeneration from wood-processing industrial residues in Ghana; practically all concluded that it was not economically viable because of the low tariffs for electricity in Ghana (around 3.5 US cents per kWh) at the time. Tariffs have more than doubled since September 1998 and average tariffs for industrial consumers are now around 7-8 US cents/kWh. This paper reviews earlier studies and undertakes a sensitivity analysis to determine effects of the new tariff regime and the investment costs for co-generation projects. More detailed technical and economic feasibility studies are needed to prepare the ground for an investment programme in cogeneration from wood residues. (author)

Final Report: Feasibility Study of Biomass in Snohomish County, Washington

Energy Technology Data Exchange (ETDEWEB)

Daryl Williams (Tulalip Tribes); Ray Clark (Clark Group)

2005-01-31

This report and its attachments summarizes the results of a unique tribal-farmer cooperative study to evaluate the feasibility of building one or more regional anaerobic digestion systems in Snohomish County, Washington.

Feasibility study for the redesign of MDOT's pavement management systems software.

Science.gov (United States)

2011-04-01

In August of 2006 the Mississippi Department of Transportation (MDOT) initiated State Study No. 191, entitled Feasibility : Study for the Redesign of MDOTs Pavement Management System (PMS) Software. At the initiation of this study, the : Dep...

100-KR-1 Operable Unit focused feasibility study report

International Nuclear Information System (INIS)

1994-11-01

The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 Feasibility Study (FS) includes development and screening of alternatives and the detailed analysis of alternatives. This focused feasibility study (FFS) was conducted for the 100-KR-1 Operable Unit at the Hanford Site in southeastern Washington. The objective of this operable unit-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for the five sites (116-K-1 crib, 116-K-2 trench, 116-KE-4 and 116-KW-3 retention basins, and process effluent pipelines) associated with the 100-KR-1 Operable Unit. The IRM candidate waste sites are determined in the limited field investigation. Site profiles are developed for each of these waste site. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

PWR decontamination feasibility study

Energy Technology Data Exchange (ETDEWEB)

Silliman, P.L.

1978-12-18

The decontamination work which has been accomplished is reviewed and it is concluded that it is worthwhile to investigate further four methods for decontamination for future demonstration. These are: dilute chemical; single stage strong chemical; redox processes; and redox/chemical in combination. Laboratory work is recommended to define the agents and processes for demonstration and to determine the effect of the solvents on PWR materials. The feasibility of Indian Point 1 for decontamination demonstrations is discussed, and it is shown that the system components of Indian Point 1 are well suited for use in demonstrations.

PWR decontamination feasibility study

International Nuclear Information System (INIS)

Silliman, P.L.

1978-01-01

The decontamination work which has been accomplished is reviewed and it is concluded that it is worthwhile to investigate further four methods for decontamination for future demonstration. These are: dilute chemical; single stage strong chemical; redox processes; and redox/chemical in combination. Laboratory work is recommended to define the agents and processes for demonstration and to determine the effect of the solvents on PWR materials. The feasibility of Indian Point 1 for decontamination demonstrations is discussed, and it is shown that the system components of Indian Point 1 are well suited for use in demonstrations

The Role of Feasibility Studies To Enhance The Natural Gas Industry

International Nuclear Information System (INIS)

Soliman, M.; Soliman, A.

2004-01-01

The purpose of this paper is to shred some light on the key issues of the gas projects feasibility studies and to answer on this question W hat is the impact of the economic, financial and marketing studies on the transmission and distribution gas project's feasibility studies in Egypt? One of the obstacles to a beneficial gas project developing is, undoubtedly, the lack of knowledge in developing countries of how to formulate a project in such a way that its potential profitability whether from a private or social viewpoint, can be estimated from as firm a basis as possible. While there has been some improvement in these areas, this is still broadly true. The basis for an efficient gas project should not only depend on technical and engineering skills, but also on sound economic, marketing, financial and legal studies and expertise. Along with these sophisticated studies, another difficult but equally important subject has to be deeply assessed, namely the element of risk. A common mis perception in the feasibility studies domain is that some people think that it should only answer the question of whether the project is profitable or not, while its main goal is to explore the question of whether the , project represents the best possible use of the limited (scarce).resources at the country's disposal (specialized manpower, capital, natural resources)

Moroccan wind farm potential feasibility. Case study

International Nuclear Information System (INIS)

Nouri, Abdellatif; Ait Babram, Mohamed; Elwarraki, Elmostafa; Enzili, Mustapha

2016-01-01

Highlights: • A new methodology for the technical feasibility of wind farm potentials is proposed. • The wind resources of two different sites in Morocco are compared. • Comparison between short and long term data using multivariate analysis is made. • Geographic information system implementation. • A 10 MW wind farm is designed and optimized. - Abstract: The subject of this paper is the elaboration of a methodology to study the technical feasibility of a wind farm potential. The implementation of this methodology allows a comparison between the wind resources of two different sites in Morocco. One site is located in the region of Essaouira, whereas the other one is located in the region of Safi. The comparison is based on real wind data collected from two masts at the heights of 30, 50, and 60 m. Each of the masts is installed at one of the mentioned potential sites over a fixed time period, lasting fifteen months for the first site, and eight months for the second one. The aim is the determination of the most applicable site presenting a good potential for a statistical study in order to predict long-term wind behaviors. Thus, the geographical situation study of the chosen site including topography, roughness and obstacles, is carried out. Furthermore, the wind resource using data, generated by the measuring masts, is evaluated. Finally, the areas which present great wind potential are located and the wind farm turbine locations are optimized by using the WAsP software.

Feasibility of multi-sector policy measures that create activity-friendly environments for children: results of a Delphi study

Directory of Open Access Journals (Sweden)

Aarts Marie-Jeanne

2011-12-01

Full Text Available Abstract Background Although multi-sector policy is a promising strategy to create environments that stimulate physical activity among children, little is known about the feasibility of such a multi-sector policy approach. The aims of this study were: to identify a set of tangible (multi-sector policy measures at the local level that address environmental characteristics related to physical activity among children; and to assess the feasibility of these measures, as perceived by local policy makers. Methods In four Dutch municipalities, a Delphi study was conducted among local policy makers of different policy sectors (public health, sports, youth and education, spatial planning/public space, traffic and transportation, and safety. In the first Delphi round, respondents generated a list of possible policy measures addressing three environmental correlates of physical activity among children (social cohesion, accessibility of facilities, and traffic safety. In the second Delphi round, policy makers weighted different feasibility aspects (political feasibility, cultural/community acceptability, technical feasibility, cost feasibility, and legal feasibility and assessed the feasibility of the policy measures derived from the first round. The third Delphi round was aimed at reaching consensus by feedback of group results. Finally, one overall feasibility score was calculated for each policy measure. Results Cultural/community acceptability, political feasibility, and cost feasibility were considered most important feasibility aspects. The Delphi studies yielded 16 feasible policy measures aimed at physical and social environmental correlates of physical activity among children. Less drastic policy measures were considered more feasible, whereas environmental policy measures were considered less feasible. Conclusions This study showed that the Delphi technique can be a useful tool in reaching consensus about feasible multi-sector policy measures. The

Symplicity multi-electrode radiofrequency renal denervation system feasibility study.

Science.gov (United States)

Whitbourn, Robert; Harding, Scott A; Walton, Antony

2015-05-01

The aim of this study was to test the safety and performance of the Symplicity™ multi-electrode radio-frequency renal denervation system which was designed to reduce procedure time during renal denervation. The multi-electrode radiofrequency renal denervation system feasibility study is a prospective, non-randomised, open label, feasibility study that enrolled 50 subjects with hypertension. The study utilises a new renal denervation catheter which contains an array of four electrodes mounted in a helical configuration at 90 degrees from each other to deliver radiofrequency energy simultaneously to all four renal artery quadrants for 60 seconds. The protocol specified one renal denervation treatment towards the distal end of each main renal artery with radiofrequency energy delivered for 60 seconds per treatment. Total treatment time for both renal arteries was two minutes. The 12-month change in office systolic blood pressure (SBP) and 24-hour SBP was -19.2±25.2 mmHg, prenal artery stenosis or hypertensive emergencies occurred. The Symplicity multi-electrode radiofrequency renal denervation system was associated with a significant reduction in SBP at 12 months and minimal complications whilst it also reduced procedure time. NCT01699529.

Code of Conduct for wind-power projects - Feasibility study

International Nuclear Information System (INIS)

Strub, P.; Ziegler, Ch.

2009-02-01

This final report deals with the results of a feasibility study concerning the development of a Code of Conduct for wind-power projects. The aim is to strengthen the acceptance of wind-power by the general public. The necessity of new, voluntary market instruments is discussed. The urgency of development in this area is quoted as being high, and the authors consider the feasibility of the definition of a code of conduct as being proven. The code of conduct can, according to the authors, be of use at various levels but primarily in project development. Further free-enterprise instruments are also suggested that should help support socially compatible and successful market development. It is noted that the predominant portion of those questioned are prepared to co-operate in further work on the subject

MRS transfer facility feasibility study

International Nuclear Information System (INIS)

Jowdy, A.K.; Smith, R.I.

1990-12-01

Under contract to the US Department of Energy, Parsons was requested to evaluate the feasibility of building a simple hot cell (waste handling) transfer facility at the Monitored Retrievable Storage (MRS) site to facilitate acceptance of spent fuel into the Federal Waste Management System starting in early 1998. The Transfer Facility was intended to provide a receiving and transfer to storage capability at a relatively low throughput rate (approximately 500 MTU/yr) and to provide the recovery capability needed on the site in the event of a transport or storage cask seal failure during a period of about two years while the larger Spent Fuel Handling Building (SFHB) was being completed. Although the original study basis postulated an incremental addition to the larger, previously considered MRS configurations, study results show that the Transfer Facility may be capable of receiving and storing spent fuel at annual rates of 3000 MTU/yr or more, making a larger fuel handling structure unnecessary. In addition, the study analyses showed that the Transfer Facility could be constructed and put into service in 15--17 months and would cost less than the previous configurations. 2 figs., 2 tabs

What is a pilot or feasibility study? A review of current practice and editorial policy

Directory of Open Access Journals (Sweden)

Cooper Cindy L

2010-07-01

Full Text Available Abstract Background In 2004, a review of pilot studies published in seven major medical journals during 2000-01 recommended that the statistical analysis of such studies should be either mainly descriptive or focus on sample size estimation, while results from hypothesis testing must be interpreted with caution. We revisited these journals to see whether the subsequent recommendations have changed the practice of reporting pilot studies. We also conducted a survey to identify the methodological components in registered research studies which are described as 'pilot' or 'feasibility' studies. We extended this survey to grant-awarding bodies and editors of medical journals to discover their policies regarding the function and reporting of pilot studies. Methods Papers from 2007-08 in seven medical journals were screened to retrieve published pilot studies. Reports of registered and completed studies on the UK Clinical Research Network (UKCRN Portfolio database were retrieved and scrutinized. Guidance on the conduct and reporting of pilot studies was retrieved from the websites of three grant giving bodies and seven journal editors were canvassed. Results 54 pilot or feasibility studies published in 2007-8 were found, of which 26 (48% were pilot studies of interventions and the remainder feasibility studies. The majority incorporated hypothesis-testing (81%, a control arm (69% and a randomization procedure (62%. Most (81% pointed towards the need for further research. Only 8 out of 90 pilot studies identified by the earlier review led to subsequent main studies. Twelve studies which were interventional pilot/feasibility studies and which included testing of some component of the research process were identified through the UKCRN Portfolio database. There was no clear distinction in use of the terms 'pilot' and 'feasibility'. Five journal editors replied to our entreaty. In general they were loathe to publish studies described as 'pilot'. Conclusion

Geology and geohydrology of the east Texas Basin. Report on the progress of nuclear waste isolation feasibility studies (1979)

International Nuclear Information System (INIS)

Kreitler, C.W.; Agagu, O.K.; Basciano, J.M.

1980-01-01

The program to investigate the suitability of salt domes in the east Texas Basin for long-term nuclear waste repositories addresses the stability of specific domes for potential repositories and evaluates generically the geologic and hydrogeologic stability of all the domes in the region. Analysis during the second year was highlighted by a historical characterization of East Texas Basin infilling, the development of a model to explain the growth history of the domes, the continued studies of the Quaternary in East Texas, and a better understanding of the near-dome and regional hydrology of the basin. Each advancement represents a part of the larger integrated program addressing the critical problems of geologic and hydrologic stabilities of salt domes in the East Texas Basin

CONTRACT Study - CONservative TReatment of Appendicitis in Children (feasibility): study protocol for a randomised controlled Trial.

Science.gov (United States)

Hutchings, Natalie; Wood, Wendy; Reading, Isabel; Walker, Erin; Blazeby, Jane M; Van't Hoff, William; Young, Bridget; Crawley, Esther M; Eaton, Simon; Chorozoglou, Maria; Sherratt, Frances C; Beasant, Lucy; Corbett, Harriet; Stanton, Michael P; Grist, Simon; Dixon, Elizabeth; Hall, Nigel J

2018-03-02

Currently, the routine treatment for acute appendicitis in the United Kingdom is an appendicectomy. However, there is increasing scientific interest and research into non-operative treatment of appendicitis in adults and children. While a number of studies have investigated non-operative treatment of appendicitis in adults, this research cannot be applied to the paediatric population. Ultimately, we aim to perform a UK-based multicentre randomised controlled trial (RCT) to test the clinical and cost effectiveness of non-operative treatment of acute uncomplicated appendicitis in children, as compared with appendicectomy. First, we will undertake a feasibility study to assess the feasibility of performing such a trial. The study involves a feasibility RCT with a nested qualitative research to optimise recruitment as well as a health economic substudy. Children (aged 4-15 years inclusive) diagnosed with acute uncomplicated appendicitis that would normally be treated with an appendicectomy are eligible for the RCT. Exclusion criteria include clinical/radiological suspicion of perforated appendicitis, appendix mass or previous non-operative treatment of appendicitis. Participants will be randomised into one of two arms. Participants in the intervention arm are treated with antibiotics and regular clinical assessment to ensure clinical improvement. Participants in the control arm will receive appendicectomy. Randomisation will be minimised by age, sex, duration of symptoms and centre. Children and families who are approached for the RCT will be invited to participate in the embedded qualitative substudy, which includes recording of recruitment consultants and subsequent interviews with participants and non-participants and their families and recruiters. Analyses of these will inform interventions to optimise recruitment. The main study outcomes include recruitment rate (primary outcome), identification of strategies to optimise recruitment, performance of trial treatment

Feasibility studies for the Forward Spectrometer

International Nuclear Information System (INIS)

Biernat, Jacek

2015-01-01

The Forward Spectrometer designed for the P-barANDA detector will consist of many different detector systems allowing for precise track reconstruction and particle identification. Feasibility studies for Forward Spectrometer done by means of specific reactions will be presented. In the first part of the paper, results of simulations focussing on rate estimates of the tracking stations based on straw tubes will be presented. Next, the importance of the Forward Tracker will be demonstrated through the reconstruction of the ψ(4040) → DD-bar decay. Finally, results from the analysis of the experimental data collected with a straw tube prototype designed and constructed at the Research Center in Juelich will be discussed. (paper)

Feasibility Study for the Development of SCWR

International Nuclear Information System (INIS)

Bae, Y. Y.; Kim, H. Y.; Cho, B. H.

2010-04-01

- As a result of feasibility study, following conclusions were drawn: · SCWR can be a strong candidate to a large-scale electric power production plant. · Infra-structure for development of an economic and safe SCWR is well established. · It is recommended to focus on the university-level fundamental research along with an international collaboration, for the time being. - The supercritical heat transfer research produced a lot of database on the small tubes and annular channels. - Among the candidate materials such as T92, Incolloy 800, MA956, ODS showed the superior characteristics

Geohydrology surrounding a potential high-level nuclear waste repository in the Paradox Basin, Utah

International Nuclear Information System (INIS)

Brandstetter, A.; Kroitoru, L.; Andrews, R.W.; Thackston, J.W.

1984-01-01

The Gibson Dome area in the Paradox Basin in southeastern Utah has been identified as a potential location for a high-level nuclear waste repository on the basis of an adequate thickness of bedded salt formations at desirable depths, suitable topography for surface facilities, few known archaeological sites, less resource potential than otherwise similar areas, and long-term geologic and tectonic stability. The area appears also suitable from a geohydrologic viewpoint, on the basis of data collected and analyses performed to date. The upper, near-surface, geologic formations include both regionally continuous water-bearing formations and locally perched ground waters that discharge into nearby surface streams and into the Colorado River. Below the Paradox salts, the formations of interest with respect to repository safety include regionally continuous water-bearing formations, with the Leadville limestone being the principal water-transmitting unit. Flows in all water-bearing formations are essentially horizontal. If a vertical connection were established through a potential repository, hydraulic gradients indicate that the flow would first be downward from the upper to the lower formations and then laterally, principally in the Leadville formation. There are some indications that minor leakage could occur into the Colorado River as close as Cataract Canyon, about 20 to 25 km (10 to 15 miles) from a potential repository location in Davis Canyon, or into the Colorado River in Marble Canyon (Arizona), about 240 km (150 miles) to the southwest. Groundwater flow from a repository to these locations is unlikely, however, since water would first have to penetrate the essentially impermeable salt layers before it would reach the Leadville formation. 11 references, 4 figures

Feasibility study on plan to utilize livestock excreta for bio-gas in Miyagi Village (Gunma Prefecture). Investigations on projects including district new energy vision establishment in fiscal 2000, and on feasibility for commercialization; Miyagimura chikusan haisetsubutsu bio gas ka energy riyo keikaku feasibility study. 2000 nendo chiiki shin energy vision sakutei nado jigyo, jigyoka feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

With objectives to utilize energy available from livestock excreta, and to properly treat the livestock excreta, a feasibility study was performed on a plan to utilize livestock excreta for bio-gas. The system to be developed is a livestock wastes treatment system to utilize gas generated by efficiently fermenting the excreta as fuel, and residual sludge solids as compost. The activity achievements were put into order by the following nine items: 1) purpose of the feasibility study, 2) method for the feasibility study, 3) the situation where the livestock industry and the hog raising industry were selected as the object of the investigation, 4) properties of hog excreta, characteristics in urine foul water treatment, technologies for urine foul water treatment (biological treatment), 5) bio-gasification of livestock wastes, 6) the basic conditions for investigating the demonstration bio-bas plants, 7) proposals and standard cases of the demonstration bio gas plants, 8) discussions and positioning of the basic system for the demonstration bio gas plants, and 9) conclusion. (NEDO)

A feasibility study of bridge deck deicing using geothermal energy.

Science.gov (United States)

2015-04-01

In this study, we investigated the feasibility of a ground-coupled system that utilizes heat energy harvested from the ground for : deicing of bridge decks. Heat exchange is performed using circulation loops integrated into the deep foundations suppo...

A feasibility study of educational tools for osteomalacia.

Science.gov (United States)

Waxman, R; Adebajo, A; Robinson, S; Walker, D; Johnson, M; Rahman, A; Samanta, A; Kumar, K; Raza, K; Helliwell, P

2017-03-01

Many people in the UK, particularly people of South Asian origin, are advised to supplement their vitamin D intake, yet most do not. This suggests an unmet educational need. The osteomalacia mind map was developed to meet this need. The mind map contains culturally sensitive images, translated into Urdu and made interactive on a DVD. This study explores the feasibility of a randomised controlled study to measure the effect of education on improving vitamin D knowledge and adherence. This was a pilot and feasibility study. Cluster randomisation was used to avoid inter person contamination. Two South Asian women's groups were recruited to receive information about osteomalacia either by interactive DVD or an Arthritis Research UK leaflet. Knowledge and compliance were tested before and after the educational interventions via a knowledge questionnaire and the measurement of vitamin D and parathormone levels. The groups were found to be mismatched for knowledge, educational attainment and language at baseline. There were also organisational difficulties and possible confounding due to different tutors and translators. The DVD group had high knowledge at baseline which did not improve. The leaflet group had low knowledge at baseline that did improve. The DVD group had lower parathormone which did not change. The leaflet group had an increase in vitamin D but parathormone remained high. Performing a randomised study with this population utilising an educational intervention was difficult to execute. If cluster randomisation is used, extreme care must be taken to match the groups at baseline.

Feasibility study of electric motors constructed with high temperature superconducting materials

International Nuclear Information System (INIS)

Jordan, H.E.

1989-01-01

The potential application of high temperature superconducting (HTSC) materials to electric motors is discussed. The specific application area of motors in electric power generating stations has been selected and a feasible study has been initiated on the use of HTSC materials in the design of motors for this application. A progress report on this feasibility study is presented. Technical challenges in both the development of HTSC wire and the design of a motor to utilize this wire are discussed. Finally, the results of design calculations comparing a superconducting motor with one of conventional design are presented assuming that success can be achieved in overcoming the technical problems which must be resolved to produce a high performance HTSC wire

Feasibility studies for decommissioning

International Nuclear Information System (INIS)

Hladky, E.

2000-01-01

In this presentation author deals with planning of decommission of the NPPs A1, V1 and V2 Bohunice and Mochovce. It was concluded that: Used model for decommissioning parameters assessment has been suitable for elaboration of initial decommissioning plans (feasibility studies); Basic assessment of main decommissioning parameters and basic comparison of various decommissioning options have been possible; Improvement of the model and corresponding software is desirable and works on software improvement began one year ago; V1-NPP initial decommissioning plan should be actualized, because initial decommissioning plan does not correspond by its content and structure to requirements of Act No. 130/98 and Nuclear Regulatory Authority Degree No. 246/99; Strategy of radioactive wastes treatment and conditioning together with technical provisions at Jaslovske Bohunice site was changed in comparison with the assumptions in 1991-92; Considered V1 NPP decommissioning options are necessary to be re-evaluated in accordance with latest development of knowledge and approaches to NPP decommissioning in the world; Specific unit costs are substantially and differentially changed in comparison with the assumptions in 1991-92; Necessity to take into account technical changes resulted from V1 NPP reconstruction. (author)

A feasibility study for the development of an SCWR in Korea

International Nuclear Information System (INIS)

Hong, Sung-Yull; Kim, Yong-Bae; Bae, Seong-Man; Lee, Kwangho; Kim, Junhyung; Bae, Yoon-Yeong

2008-01-01

Korea is participating in international collaboration activities since the selection of supercritical water-cooled reactor (SCWR) as one of the viable candidates for Generation IV reactor systems in 2002. The SCWR has been selected by Generation IV International Forum (GIF) since it is a very feasible candidate reactor system for a large-scale electricity production in commercially viable manner. However, the level of Korean participation is still limited to several key areas and the decision-making on whether going into full-scale research is yet to be made. In three circumstances it has been decided to launch a feasibility study in March 2007 to assess the domestic capability and resources as well as economics for development of an SCWR and to identify the required research areas. This paper introduces the project named 'A feasibility study for the development of an SCWR in Korea', which is sponsored by MEST (Ministry of Education, Science and Technology) in Korea. The main purpose of this study is to provide a basis for establishing a government policy in consideration of the unique domestic environment for SCWR development. This study includes three different areas of evaluation aspect, i.e., policy and environment, technology and safety, and economics. In policy and environment aspects, the needs of SCWR development is evaluated in terms of future electricity demand, reactor type strategy, fuel cycle policy, and available infrastructure in Korea, etc. In technology and safety aspects, evaluation is performed to identify the most optimum way of SCWR R and D strategy and several fundamental studies including heat transfer, code developments, and materials are performed in parallel. Finally, in economic aspect, the economic feasibility of SCWR development is assessed in comparison with the Korean nuclear power plants OPR1000 and APR1400 and other comparable overseas reactors. This study will be finished by 2010 and the results of the assessment will become a

Transvaginal uterosacral ligament hysteropexy: a retrospective feasibility study.

Science.gov (United States)

Milani, Rodolfo; Frigerio, Matteo; Manodoro, Stefano; Cola, Alice; Spelzini, Federico

2017-01-01

Uterine-sparing procedures could be attractive in patients concerned about preservation of fertility and change in corporeal image and sexuality. Transvaginal uterosacral hysteropexy can provide an alternative mesh-free technique for uterine suspension. This study aimed to evaluate the feasibility of transvaginal uterine suspension to uterosacral ligaments in terms of operative data, complications, midterm efficacy, and patient satisfaction. This retrospective study analyzed the first 20 cases of transvaginal hysteropexy through bilateral high uterosacral ligaments (modified Shull technique) performed in our Institution. Mean follow-up was 33.2 months. The procedure was performed in 84 ± 19 min ,and blood loss was 228 ± 139 ml. Three mild complications (15 %) were observed. Recurrence [Pelvic Organ Prolapse Quantification system (POP-Q) stage ≥ II was observed in five patients (25 %), and three of them (15 %) required reintervention. Mean Patient Global Impression of Improvement score was "much improved." Two woman (40 %) who had not fulfilled their childbearing desire obtained a pregnancy. Both underwent elective caesarean section at term. Transvaginal uterosacral hysteropexy appears a feasible mesh-free technique for apical support. This procedure can be indicated in women with the desire of preserving fertility or who prefer a uterine-sparing surgical option.

7 CFR 1980.442 - Feasibility studies.

Science.gov (United States)

2010-01-01

... management, nature and extent of market area, marketing plans for sale of projected output, extent of... Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS...) PROGRAM REGULATIONS (CONTINUED) GENERAL Business and Industrial Loan Program § 1980.442 Feasibility...

100-HR-2 Operable Unit Focused Feasibility study report

International Nuclear Information System (INIS)

1995-01-01

The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) Feasibility Study (FS) includes development and screening of alternatives (Phases 1 and 2) and the detailed analysis of alternatives (Phase 3). This focused feasibility study (FFS) was conducted for the 100-HR-2 Operable Unit (OU) at the Hanford Site in southeastern Washington. This FFS constitutes the Phase 3 portion of the FS process for the remedial alternatives initially developed and screened in the 100 Area Feasibility Study Phases 1 and 2 (DOE-RL 1993a). The objective of this OU-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for the seven IRM candidate sites associated with the 100-HR-2 OU. The IRM candidate waste sites identified in Table ES-1 are determined in the limited field investigation (DOE-RL 1994b). Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented. A summary for the 100-HR-2 IRM candidate waste site is as follows: none of the waste sites require additional alternative development. six of the seven waste sites directly plug into the waste site group alternatives. The site-specific detailed analysis is conducted, referencing the waste site group analysis as appropriate. A waste site detailed analysis summary is presented in Table ES-1.A comparative analysis of remedial alternatives is presented for each waste site. A summary of the comparative analysis is presented in Table ES-2

The Pocos de Caldas project feasibility study: 1986-7

International Nuclear Information System (INIS)

Smellie, J.A.T.; Chapman, N.A.; Franca, E.P.

1987-01-01

This paper presents feasibility studies to investigate the uranium, thorium and rare earth deposits, in Morro do Ferro and the uranium mine in Osamu Utsumi, Brazil, as natural analogues to link rock geochemistry and hydrogeological systems to assess radionuclide mobility. Ore samples were analysed to obtain uranium concentrations and hydraulic tests were carried out. (UK)

Feasibility study on fission moly target development

International Nuclear Information System (INIS)

Kim, Byung Ku; Kim, Seong Nyun; Shon, Dong Seong; Choi, Chang Beom; Lee, Jae Kuk; Park, Jin Ho; Jeong, Won Myung; Jeon, Kwan Sik; You, Jae Hyung; Kang, Kyung Chul; Ahn, Jong Hwan; Ju, Po Kuk

1996-01-01

A multi-purpose research reactor, HANARO has been operated on the beginning of 1995 and can be utilized for production of various radioisotopes. And a R and D program for fission Mo production was established, and the technical and economical feasibility study has been performed for fission Mo production in Korea. In this study the process for fission Mo production was recommended as follows; 1. Target : UO 2 of annulus type. 2. Separation and purification : Nitric acid dissolution → Alumina adsorption → Benzoin oxime precipitation → Alumina adsorption. And more desirable plan for steady supply of fission Mo were suggested in following viewpoints; 1. Technical collaboration with foreign company. 2. Backup supply system. 3. Marketing arrangement. (Author)

Feasibility Study for Paragon - Bisti Solar Ranch

Energy Technology Data Exchange (ETDEWEB)

Benally, Thomas [Navajo Hopi Land Commission Office (NHLCO), Window Rock, AZ (United States)

2015-06-01

The Navajo Hopi Land Commission Office (NHLCO) and Navajo Nation (NN) plan to develop renewable energy (RE) projects on the Paragon-Bisti Ranch (PBR) lands, set aside under the Navajo Hopi Land Settlement Act (NHLSA) for the benefit of Relocatees. This feasibility study (FS), which was funded under a grant from DOE’s Tribal Energy Program (TEP), was prepared in order to explore the development of the 22,000-acre PBR in northwestern New Mexico for solar energy facilities. Topics covered include: • Site Selection • Analysis of RE, and a Preliminary Design • Transmission, Interconnection Concerns and Export Markets • Financial and Economic Analysis • Environmental Study • Socioeconomic and Cultural Factors • Next Steps.

Cadaveric surgery in core gynaecology training: a feasibility study.

Science.gov (United States)

Lim, Chou Phay; Roberts, Mark; Chalhoub, Tony; Waugh, Jason; Delegate, Laura

2018-01-01

Fresh frozen cadaver training has been proposed as a better model than virtual reality simulators in laparoscopy training. We aimed to explore the relationship between cadaveric surgical training and increased surgical confidence.To determine feasibility, we devised two 1-day cadaveric surgical training days targeted at trainees in obstetrics and gynaecology. Seven defined surgical skills were covered during the course of the day. The relationship between surgical training and surgical confidence was explored using both quantitative (confidence scores) and qualitative tools (questionnaires). Participants rated a consistent improvement in their level of confidence after the training. They universally found the experience positive and three overarching themes emerged from the qualitative analysis including self-concept, social persuasion and stability of task. It is pragmatically feasible to provide procedure-specific cadaveric surgical training alongside supervised clinical training. This small, non-generalisable study suggests that cadaveric training may contribute to an increase in surgical self-confidence and efficacy. This will form the basis of a larger study and needs to be explored in more depth with a larger population.

Feasibility study for the European Reliability Data System (ERDS)

International Nuclear Information System (INIS)

Mancini, G.

1980-01-01

In the framework of the Reactor Safety Programme of the Commission of the European Communities, the JRC - Ispra Establishment has performed a feasibility study for an integrated European Reliability Data System, the aim of which is the collection and organization of information related to the operation of LWRs with regard to component and systems behaviour, abnormal occurrences, outages, etc. Component Event Data Bank (CEGB), Abnormal Occurrences Reporting System, Generic Reliability Parameter Data Bank, Operating Unit Status Reports and the main activities carried out during the last two years are described. The most important achievements are briefly reported, such as: Reference Classification for Systems, Components and Failure Events, Informatic Structure of the Pilot Experiment of the CEDB, Information Retrieval System for Abnormal Occurrences Reports, Data Bank on Component Reliability Parameters, System on the Exchange of Operation Experience of LWRs, Statistical Data Treatment. Finally, the general conclusions of the feasibility study are summarized: the possibility and the usefulness for the creation of an integrated European Reliability Data System are outlined. (author)

A Feasibility Study to Evaluate Wind Energy Potential on the Navajo Nation

Energy Technology Data Exchange (ETDEWEB)

Terry Battiest

2012-11-30

The project, A Feasibility Study to Evaluate Wind Energy Potential on the Navajo Nation, is funded under a solicitation issued by the U.S. Department of Energy Tribal Energy Program. Funding provided by the grant allowed the Navajo Nation to measure wind potential at two sites, one located within the boundaries of the Navajo Nation and the other off-reservation during the project period (September 5, 2005 - September 30, 2009). The recipient for the grant award is the Navajo Tribal Utility Authority (NTUA). The grant allowed the Navajo Nation and NTUA manage the wind feasibility from initial site selection through the decision-making process to commit to a site for wind generation development. The grant activities help to develop human capacity at NTUA and help NTUA to engage in renewable energy generation activities, including not only wind but also solar and biomass. The final report also includes information about development activities regarding the sited included in the grant-funded feasibility study.

Preliminary study on the feasibility of ductless fuel assembly for fast reactors

International Nuclear Information System (INIS)

Shibahara, Itaru; Enokido, Yuji

1988-01-01

Preliminary study on the feasibility of ductless fuel assembly for fast reactors has been conducted. The primary concern is with forecasting the thermal hydraulic characteristics and the heat removal efficiency from the core. The thermal hydraulic analysis revealed the coolant mixing in the core at steady state operating condition was not intensive and the coolant temperature increase was almost proportional to the power of each assembly. The hot spot analysis of the ductless core indicated that the hottest temperature in the core could be comparable with the temperature of the conventional ducted core, even in case the radial power flattening was not actively pursued but with adopting ducted radial blanket assemblies. Under off-normal conditions, the ductless core had improved heat removal capability which was caused by inter-assembly coolant flow. The study has indicated the feasibility of the ductless fuel assembly for fast reactors. The experiments to demonstrate the feasibility will be the next key process for the development. (author)

Anticipatory precrash restraint sensor feasibility study: Final report

Energy Technology Data Exchange (ETDEWEB)

Kercel, S.W.; Dress, W.B.

1995-08-01

This report explores feasibility of an anticipatory precrash restraint sensor. The foundation principle is the anticipation mechanism found at a primitive level of biological intelligence and originally formalized by the mathematical biologist Robert Rosen. A system based on formal anticipatory principles should significantly outperform conventional technologies. It offers the prospect of high payoff in prevention of death and injury. Sensors and processes are available to provide a good, fast, and inexpensive description of the present dynamical state of the vehicle to the embedded system model in the anticipation engine. The experimental part of this study found that inexpensive radar in a real-world setting does return useful data on target dynamics. The data produced by a radar system can be converted to target dynamical information by good, fast and inexpensive signal-processing techniques. Not only is the anticipatory sensor feasible, but further development under the sponsorship of the National Highway Traffic Safety Administration is necessary and desirable. There are a number of possible lines of follow-on investigation. The level of effort and expected benefits of various alternatives are discussed.

Oak Ridge National Laboratory remedial investigation/feasibility study

International Nuclear Information System (INIS)

Glenn, R.D.; Hoffman, J.M.; Hyde, L.D.

1988-01-01

The Oak Ridge National Laboratory (ORNL) Remedial Investigation/ Feasibility Study (RI/FS) began in June 1987 to evaluate 13 contaminated waste area groupings (WAGs) to determine the feasibility and benefits of potential remedial action. The RI/FS and any future remedial action at ORNL will be of national significance and will likely lead to developments that will become models for environmental investigations and cleanups. Bechtel National, Inc. and a team of subcontractors will be working with Martin Marietta Energy systems to conduct intensive field investigations to obtain data required to evaluate the WAGs. The RI/F project continued in FY 1988 with project planning and preparation for field activities. Remedial Investigation (RI) Plans were prepared for 10 of the 13 WAGs. These plans were developed with sufficient information to ensure compliance with regulatory requirements, with intensive attention given to environmental, safety, and health protection; waste management; data management; and quality assurance. This paper reports on the progress made during FY 1988 and discusses activities planned for FY 1989

Cogeneration feasibility study in the Gulf States Utilities service area

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

Sites in the Gulf States Utilities service are considered for cogeneration feasibility studies. The sources of steam considered for the Orange, Texas and Geismar, Lake Charles, and North Baton Rouge, Louisiana sites include oil, coal, HTGR steamers, consolidated nuclear steam system, atmospheric fluidized-bed coal combustion, and coal gasification. Concepts concerning cogeneration fuel systems were categorized by technical applicability as: current technology (pulverized coal-fired boilers and fuel oil-fired boilers), advanced technology under development (HTGR steamers and the CNSS), and advanced technology for future development (atmospheric fluidized-bed boilers and coal gasification). In addition to providing data on cogeneration plant generally useful in the US, the study determined the technical and economic feasibility of steam and electric power cogeneration using coal and nuclear fuels for localized industrial complexes. Details on site selection, plant descriptions, cost estimates, economic analysis, and plant schedule and implementation. (MCW)

Nasal Unit Transplantation: A Cadaveric Anatomical Feasibility Study.

Science.gov (United States)

Dorafshar, Amir H; Mundinger, Gerhard S; Robinson, Brent; Tuffaha, Sami; Brandacher, Gerald; Byrne, Patrick; Walton, Robert L

2017-05-01

Background  The science and technical acumen in the field of vascularized composite allotransplantation has progressed rapidly over the past 15 years, and transplantation of specialized units of the face, such as the nose, appears possible. No study to date has evaluated the technical feasibility of isolated nasal unit transplantation (NUT). In this study, we explore the anatomy and technical specifics of NUT. Methods  In this study, four fresh cadaver heads were studied. Bilateral vascular pedicle dissections were performed in each cadaver. The facial artery was cannulated and injected with food dye under physiologic pressure in two cadavers, and with lead oxide mixture in two cadavers to evaluate perfusion territories supplied by each vascular pedicle. Results  The facial artery and vein were found to be adequate pedicles for NUT. Divergent courses of the vein and artery were consistently identified, which made for a bulky pedicle with necessary inclusion of large amounts of subcutaneous tissue. In all cases, the artery remained superficial, while the vein coursed in a deeper plane, and demonstrated consistent anastomoses with the superior transverse orbital arcade. While zinc oxide injection of the facial artery demonstrated filling of the nasal vasculature across the midline, dye perfusion studies suggested that unilateral arterial inflow may be insufficient to perfuse contralateral NUT components. Discrepancies in these two studies underscore the limitations of nondynamic assessment of nutritive perfusion. Conclusion  NUT based on the facial artery and facial vein is technically feasible. Angiosome evaluation suggests that bilateral pedicle anastomoses may be required to ensure optimal perfusion. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Telephone Care Management of Fall Risk:: A Feasibility Study.

Science.gov (United States)

Phelan, Elizabeth A; Pence, Maureen; Williams, Barbara; MacCornack, Frederick A

2017-03-01

Care management has been found to be more effective than usual care for some chronic conditions, but few studies have tested care management for prevention of elder falls. This study aimed to assess the feasibility and preliminary efficacy of telephone care management of older adults presenting for medical attention due to a fall. The setting was an independent practice association in western Washington serving 1,300 Medicare Advantage-insured patients. Patients aged ≥65 years treated for a fall in an emergency department or their primary care provider's office were contacted via telephone by a care manager within 48 hours of their fall-related visit and invited to participate in a telephone-administered interview to identify modifiable fall risk factors and receive recommendations and follow-up to address identified risk factors. Data from care manager records, patient medical records, and healthcare claims for the first 6 months (November 2009-April 2010) of program implementation were analyzed in 2011. The feasibility of screening and management of fall risk factors over the telephone and the effect on medically attended falls were assessed. Twenty-two patients eligible for fall care management were reached and administered the protocol. Administration took 15-20 minutes and integrated easily with the care manager's other responsibilities. Follow-through on recommendations varied, from 45% for those for whom exercise participation was recommended to 100% for other recommendations. No medically attended falls occurred over 6 months of follow-up. Telephone care management of fall risk appears feasible and may reduce falls requiring medical attention. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

The environmental energy sector programme. Poland: Appendices to feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The appendices contain Energy Law, Act of 10 April 1997 and also more specific details from the feasibility study for the procurement of a financial solution to the modernisation of the combined heat and power plant in the city of Zielona Gora, Poland. (EHS)

Geohydrology of the unsaturated zone at the burial site for low-level radioactive waste near Beatty, Nye County, Nevada

International Nuclear Information System (INIS)

Nichols, W.D.

1987-01-01

Low-level radioactive solid waste has been buried in trenches at a site near Beatty, NV, since 1962. In 1976, as part of a national program, the US Geological Survey began a study of the geohydrology of the waste burial site to provide a basis for estimating the potential for radionuclide migration in the unsaturated zone beneath the waste burial trenches. The waste burial facility is in the northern Amargosa Desert about 170 kilometers (km) northwest of Las Vegas, NV. The site is underlain by poorly stratified deposits of gravelly or silty sand and sandy gravel, and thick beds of clayey sediments. A numerical analysis demonstrated that a potential exists for deep percolation despite high annual evaporation demands, and provided predictions of the time of year and the antecedent conditions that enhance the probability of deep percolation. Soil moisture profiles obtained monthly over an 18-month period demonstrate that deep percolation does occur. Calculation of downward moisture movement through the waste trench backfill material, on the basis of simplified assumptions, suggests that moisture could have penetrated as much as 6 m below land surface from 1963, when the oldest trenches were closed, to 1980, but that the moisture requirement for such penetration far exceeded the amount of moisture actually available. Steady-state downward movement of moisture at depths greater than 10 m and beneath the waste burial trenches would be on the order of 4 cu m/1,000 yr, assuming a steady flux rate of 0.1 microcentimeter/day. 37 refs., 32 figs., 17 tab

Geothermal application feasibility study for the New Mexico Institute of Mining and Technology Campus

Energy Technology Data Exchange (ETDEWEB)

Miller, A.R.

1978-04-01

This study was limited to determining the economic feasibility of providing the space heating, water heating, space cooling, and electrical power needs of New Mexico Tech from geothermal energy. The means of obtaining the required heat and water from the earth, and the possibility of corrosive effects were not part of this study. The results indicate that space heating and water heating are economically feasible if the cost of developing a geothermal source is not included. The major expense then is the pipeline used to convey the energy to the campus. calculations show that this cost is approximately two to three times our current annual heating bill, The study also showed that it would not be economically feasible to provide our relatively small space cooling and electrical energy needs from geothermal energy.

Exoskeleton for Soldier Enhancement Systems Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Jansen, J.F.

2000-09-28

The development of a successful exoskeleton for human performance augmentation (EHPA) will require a multi-disciplinary systems approach based upon sound biomechanics, power generation and actuation systems, controls technology, and operator interfaces. The ability to integrate key components into a system that enhances performance without impeding operator mobility is essential. The purpose of this study and report are to address the issue of feasibility of building a fieldable EHPA. Previous efforts, while demonstrating progress and enhancing knowledge, have not approached the level required for a fully functional, fieldable system. It is doubtless that the technologies required for a successful exoskeleton have advanced, and some of them significantly. The question to be addressed in this report is have they advanced to the point of making a system feasible in the next three to five years? In this study, the key technologies required to successfully build an exoskeleton have been examined. The primary focus has been on the key technologies of power sources, actuators, and controls. Power sources, including internal combustion engines, fuel cells, batteries, super capacitors, and hybrid sources have been investigated and compared with respect to the exoskeleton application. Both conventional and non-conventional actuator technologies that could impact EHPA have been assessed. In addition to the current state of the art of actuators, the potential for near-term improvements using non-conventional actuators has also been addressed. Controls strategies, and their implication to the design approach, and the exoskeleton to soldier interface have also been investigated. In addition to these key subsystems and technologies, this report addresses technical concepts and issues relating to an integrated design. A recommended approach, based on the results of the study is also presented.

FIRST FEASIBILITY STUDY FOR EXL WITH PROTOTYPE DETECTORS AT THE ESR AND DETECTOR SIMULATIONS

NARCIS (Netherlands)

Kalantar-Nayestanaki, N.; Moeini, H.; Mahjour-Shafiei, M.; Aksouh, F.; Beckert, K.; Beller, P.; Boretzky, K.; Chatillon, A.; Corsi, A.; Egelhof, P.; Emling, H.; Ickert, G.; Ilieva, S.; Kozhuharov, C.; Le Bleis, T.; Le Xuang, X. C.; Litvinov, Y.; Mahata, K.; Meier, J. P.; Nolden, F.; Popp, U.; Simon, H.; Steck, M.; Stoehlker, T.; Weick, H.; Zalite, A.; Kiselev, O.; Jourdan, J.; Kiselev, D.; Werthmueller, D.; Paschalis, S.

This contribution presents some results from the first feasibility measurement performed at GSI using a 350 MeV/nucleon (136)Xe beam and a Hydrogen gas-jet target. In this feasibility study, one element of every possible detection part of the future EXL detection system was investigated. In

Feasibility, safety, acceptability, and functional outcomes of playing Nintendo Wii Fit Plus™ for frail elderly: study protocol for a feasibility trial.

Science.gov (United States)

Gomes, Gisele Cristine Vieira; Bacha, Jéssica Maria Ribeiro; do Socorro Simões, Maria; Lin, Sumika Mori; Viveiro, Larissa Alamino Pereira; Varise, Eliana Maria; Filho, Wilson Jacob; Pompeu, José Eduardo

2017-01-01

Frailty can be defined as a medical syndrome with multiple causes and contributors, characterized by diminished strength and endurance and reduced physiological function that increases the vulnerability to develop functional dependency and/or death. Studies have shown that the most commonly studied exercise protocol for frail older adults is the multimodal training. Interactive video games (IVGs) involve tasks in virtual environments that combine physical and cognitive demands in an attractive and challenging way. The aim of this study will be to evaluate the feasibility, safety, acceptability, and functional outcomes of playing Nintendo Wii Fit Plus TM (NWFP) for frail older adults. The study is a randomized controlled, parallel group, feasibility trial. Participants will be randomly assigned to the experimental group (EG) and control group (CG). The EG will participate in 14 training sessions, each lasting 50 min, twice a week. In each training session, the participants will play five games, with three attempts at each game. The first attempt will be performed with the assistance of a physical therapist to correct the movements and posture of the patients and subsequent attempts will be performed independently. Scores achieved in the games will be recorded. The participants will be evaluated by a blinded physical therapist at three moments: before and after intervention and 30 days after the end of the intervention (follow-up). We will assess the feasibility, acceptability, safety, and clinical outcomes (postural control, gait, cognition, quality of life, mood, and fear of falling). Due to the deficiencies in multiple systems, studies have shown that multimodal interventions including motor-cognitive stimulation can improve the mobility of frail elderly adults. IVGs, among them the NWFP, are considered as a multimodal motor-cognitive intervention that can potentially improve motor and cognitive functions in the frail elderly. However, there is still no evidence

Development of new port in Minahasa Utara: A-pre feasibility study

Science.gov (United States)

Hamzah, Suharman; Abdurahman, Asad; Saputra, Reza; Aprianti, Evi

2017-11-01

In order to support Indonesian Government priority sector to build toll maritime in conjunction to connect "nusantara" as an archipelago country, and also to develop the frontier area of Indonesia, the existence of a port should get more in attention as the gate of Indonesia. A port has significant role in changing of transport mode and at the end as catalyst of economic growth. An important thing from pre-feasibility studies is the priority factor will clearly shown wheather it is good or fair. As a supporting to service passenger moving, container, general cargo and also bulk, a port is necessary to have an excellent design and planning. A pre-feasibility study is required to obtain a scientific basis based on value of interest and the necessity of the region. A pre-feasibility study in this paper aims to identify potential support of the region and giving priority location of development of new port in Minahasa Utara regarding to spatial, government issues, transportation aspect, regional economics, environmental aspect and technical aspect consideration. Experimental Method used are qualitative and quantitative, going through to the data obtained and supported by interview on the spot as well as questionnaire surveys. Result of this paper showing that there are 5 locations suitable with the requirements. Based on the level of priority, high (Kema, Likupang), moderate (Linuhu, Kahuku) and low (Gangga 1).

Feasibility study on the establishment of the IAEA international nuclear university

International Nuclear Information System (INIS)

Lee, E. J.; Kim, Y. T.; Nam, Y. M. and others

2002-09-01

The purpose of this project is to support 2002-2003 the IAEA project D.4.0.2, facilitating education, training and research in nuclear science and related fields, especially for a feasibility study on the establishment of the Agency sponsored International Nuclear University. Through this project, the abstract principle for a feasibility study on the establishment of the Agency sponsored International Nuclear university, which contains the new concepts and its objectives, principles to achieve the objectives, its curriculum outline and operation system, suggested project activities, was developed and submitted to the Agency. The Korean proposal were presented several times at the IAEA meetings and other international meetings related nuclear human resources development for understanding the necessity of a feasibility study on the establishment of the Agency sponsored international nuclear university with Member States. And the Korean proposal included such as the organization of a worldwide network using information and communication technology among Merber States' research institutes and training/education centers, curriculum outline and operation system of the INU will be produced. Also for further cooperation of the IAEA INU project implementation with the Agency, hosting IAEA INIS mirror site, establishment of the RCA region office, establishment of the INTEC at the Korean Atomic Energy Research Institute, and advanced curriculum of nuclear technology linked with NT, BT, ET, IT were made progress as a part of conceptualizing of the IAEA project

Feasibility study on the development of proton accelerator

Energy Technology Data Exchange (ETDEWEB)

Chung, Ki Hyung; Bang, Hyung Chan; Cho, Yong Sup [Seoul National University, Seoul (Korea, Republic of); Kim, Young Rak [Church Environment Research Institute, Seoul (Korea, Republic of); Nam Kung, Won; Cho, Moo Hyun [Pohang University of Science and Technology, Pohang (Korea, Republic of); Seo, Tae Suk [Cartolrik University, Seoul (Korea, Republic of); Woo, Hyung Joo [Nature Research Institute, Seoul (Korea, Republic of); Lee, Kyung Soo [Basic Study Research Institute, Seoul (Korea, Republic of); Lee, Hun Joo [Cheju National University, Cheju (Korea, Republic of); Chang, Soon Hong; Cho, Nam Jin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Han, Jeon Kun [Sungkyunkwan University, Seoul (Korea, Republic of)

1996-10-01

A feasibility on the development of a high energy proton accelerator to be used for R and D in the nuclear field of korea was studied. The proposed one is a proton linac with parameters of about 1 GeV, 20 mA which can supply enough neutrons by the spallation reaction to drive a subcritical reactor. It= is expected to solve the intrinsic problem in the nuclear field such as safety, nuclear waste, proliferation and resource. The study was carried out through a multi-institutional cooperation of universities, institute and industry for a national consensus. 5 refs., 8 tabs., 8 figs. (author)

Economic and technical feasibility study of compressed air storage

Energy Technology Data Exchange (ETDEWEB)

1976-03-01

The results of a study of the economic and technical feasibility of compressed air energy storage (CAES) are presented. The study, which concentrated primarily on the application of underground air storage with combustion turbines, consisted of two phases. In the first phase a general assessment of the technical alternatives, economic characteristics and the institutional constraints associated with underground storage of compressed air for utility peaking application was carried out. The goal of this assessment was to identify potential barrier problems and to define the incentive for the implementation of compressed air storage. In the second phase, the general conclusions of the assessment were tested by carrying out the conceptual design of a CAES plant at two specific sites, and a program of further work indicated by the assessment study was formulated. The conceptual design of a CAES plant employing storage in an aquifer and that of a plant employing storage in a conventionally excavated cavern employing a water leg to maintain constant pressure are shown. Recommendations for further work, as well as directions of future turbo-machinery development, are made. It is concluded that compressed air storage is technically feasible for off-peak energy storage, and, depending on site conditions, CAES plants may be favored over simple cycle turbine plants to meet peak demands. (LCL)

Feasibility Study Analysis of Establishing Archery Sports Special Place

Science.gov (United States)

Tarigan, U. P. P.; Mardhatillah, A.; Budiman, I.; Sembiring, A. C.; Ramadhan, M. S.

2018-04-01

This study essentially discusses the basic concepts related to the decision and process of selecting a sports archery business project in order to provide economic and social benefits over time. Archery sports is a sport that requires special skills, both accuracy, coordination mental training and improves the physical condition of the prime. In Medan, it's still a bit of practice archery, but many people love this sport. From the data collected, there are three locations where archery in the city of the field of the Sunggal Knights is located at Jl Tunggul Hitam no.1A, Kec. Medan Sunggal, Avros Educational Park Aval address at Avros Street No.60 Medan, and the Knights of Johor Archery Club which is located at Jl. The work of Darma Gg. Ujung Family, Medan Johor. Therefore a feasibility study was undertaken in establishing an archery sports place in the field. The aspects to be considered in making feasibility studies are market and marketing aspects, technical and equipment aspects, management aspects, legal aspects, economic and social aspects, and financial aspects. Financial analysis using own capital got Payback Period 3 years 5,8 months, Net Present Value Rp 11.684.026 and obtained Internal Rate of Return of 17%.

Feasibility study on commercialized fast reactor cycle systems. (1) Current status of the phase-II study

International Nuclear Information System (INIS)

Sagayama, Yutaka

2005-01-01

A feasibility study on commercialized fast reactors including related nuclear fuel cycle systems has been started from Japanese fiscal year 1999 by a Japanese joint project team of Japan Nuclear Cycle Development Institute and the Japan Atomic Power Company. This project aims at elucidating prominent fast reactor cycle systems that will respond to various needs of society in the future, together with economic competitiveness as future electricity supply systems. Challenging technology goals for the fast reactor cycle systems were defined in five targets: safety, economic competitiveness, reduction of environmental burden, efficient utilization of nuclear fuel resources and enhancement of nuclear non-proliferation. As the results of the feasibility study up to now, it is confirmed as the interim results that the combination of sodium-cooled fast reactors with oxide fuels, advanced aqueous reprocessing and simplified pellet fuel fabrication is highly suited to the development targets. The cost would be highly reduced by the adoption of innovative technologies, which feasibility is relatively clear and some R and D issues are now under progress. (author)

Training Corrective Maintenance Performance on Electronic Equipment with CAI Terminals: I. A Feasibility Study.

Science.gov (United States)

Rigney, Joseph W.

A report is given of a feasibility study in which several possible relationships between student, computer terminal, and electronic equipment were considered. The simplest of these configurations was set up and examined in terms of its feasibility for teaching the performance of fault localization on a Navy transceiver. An instructional program…

Practice Study Outpatient Psychotherapy - Switzerland (PAP-S) : Study design and feasibility (Revised edition)

OpenAIRE

Wyl, Agnes von; Crameri, Aureliano; Koemeda, Margit; Tschuschke, Volker; Schulthess, Peter

2016-01-01

Revised edition of Von Wyl, A., Crameri, A., Koemeda, M., Tschuchke, V. & Schulthess, P. (2013). The PAP-S (Practice of Ambulant Psychotherapy-Study), Switzerland: Study Design and Feasibility. Zurich University of Applied Sciences, Zurich. The original article was published in German: von Wyl, A., Crameri, A., Koemeda, M., Tschuschke, V. & Schulthess, P. (2013). Praxisstudie ambulante Psychotherapie Schweiz (PAP-S): Studiendesign und Machbarkeit. Psychotherapie-Wissenschaft, 1, 6-22; op...

Feasibility study report for Operable Unit 4: Volume 1

International Nuclear Information System (INIS)

1994-02-01

This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP

Solar feasibility study for site-specific industrial-process-heat applications. Final report

Energy Technology Data Exchange (ETDEWEB)

Murray, O.L.

1980-03-18

This study addresses the technical feasibility of solar energy in industrial process heat (IPH) applications in Mid-America. The study was one of two contracted efforts covering the MASEC 12-state region comprised of: Illinois, Michigan, North Dakota, Indiana, Minnesota, Ohio, Iowa, Missouri, South Dakota, Kansas, Nebraska, Wisconsin. The results of our study are encouraging to the potential future role of solar energy in supplying process heat to a varied range of industries and applications. We identified and developed Case Study documentation of twenty feasible solar IPH applications covering eight major SIC groups within the Mid-American region. The geographical distribution of these applications for the existing range of solar insolation levels are shown and the characteristics of the applications are summarized. The results of the study include process identification, analysis of process heat requirements, selection of preliminary solar system characteristics, and estimation of system performance and cost. These are included in each of the 20 Case Studies. The body of the report is divided into two primary discussion sections dealing with the Study Methodology employed in the effort and the Follow-On Potential of the identified applications with regard to possible demonstration projects. The 20 applications are rated with respect to their relative overall viability and procedures are discussed for possible demonstration project embarkment. Also, a possible extension of this present feasibility study for late-comer industrial firms expressing interest appears worthy of consideration.

Assessing the feasibility of the Effectiveness of Discontinuing Bisphosphonates trial: a pilot study.

Science.gov (United States)

Wright, N C; Foster, P J; Mudano, A S; Melnick, J A; Lewiecki, M E; Shergy, W J; Curtis, J R; Cutter, G R; Danila, M I; Kilgore, M L; Lewis, E C; Morgan, S L; Redden, D T; Warriner, A H; Saag, K G

2017-08-01

The Effectiveness of Discontinuing Bisphosphonates (EDGE) study is a planned pragmatic clinical trial to guide "drug holiday" clinical decision making. This pilot study assessed work flow and feasibility of such a study. While participant recruitment and treatment adherence were suboptimal, administrative procedures were generally feasible and minimally disrupted clinic flow. The comparative effectiveness of continuing or discontinuing long-term alendronate (ALN) on fractures is unknown. A large pragmatic ALN discontinuation study has potential to answer this question. We conducted a 6-month pilot study of the planned the EDGE study among current long-term ALN users (women aged ≥65 with ≥3 years of ALN use) to determine study work flow and feasibility including evaluating the administrative aspects of trial conduct (e.g., time to contract, institutional review board (IRB) approval), assessing rates of site and participant recruitment, and evaluating post-randomization outcomes, including adherence, bisphosphonate-associated adverse events, and participant and site satisfaction. We assessed outcomes 1 and 6 months after randomization. Nine sites participated, including seven community-based medical practices and two academic medical centers. On average (SD), contract execution took 3.4 (2.3) months and IRB approval took 13.9 (4.1) days. Sites recruited 27 participants (13 to continue ALN and 14 to discontinue ALN). Over follow-up, 22% of participants did not adhere to their randomization assignment: 30.8% in the continuation arm and 14.3% in the discontinuation arm. No fractures or adverse events were reported. Sites reported no issues regarding work flow, and participants were highly satisfied with the study. Administrative procedures of the EDGE study were generally feasible, with minimal disruption to clinic flow. In this convenience sample, participant recruitment was suboptimal across most practice sites. Accounting for low treatment arm adherence, a

Feasibility Study and Demonstration of an Aluminum and Ice Solid Propellant

Directory of Open Access Journals (Sweden)

Timothee L. Pourpoint

2012-01-01

Full Text Available Aluminum-water reactions have been proposed and studied for several decades for underwater propulsion systems and applications requiring hydrogen generation. Aluminum and water have also been proposed as a frozen propellant, and there have been proposals for other refrigerated propellants that could be mixed, frozen in situ, and used as solid propellants. However, little work has been done to determine the feasibility of these concepts. With the recent availability of nanoscale aluminum, a simple binary formulation with water is now feasible. Nanosized aluminum has a lower ignition temperature than micron-sized aluminum particles, partly due to its high surface area, and burning times are much faster than micron aluminum. Frozen nanoscale aluminum and water mixtures are stable, as well as insensitive to electrostatic discharge, impact, and shock. Here we report a study of the feasibility of an nAl-ice propellant in small-scale rocket experiments. The focus here is not to develop an optimized propellant; however improved formulations are possible. Several static motor experiments have been conducted, including using a flight-weight casing. The flight weight casing was used in the first sounding rocket test of an aluminum-ice propellant, establishing a proof of concept for simple propellant mixtures making use of nanoscale particles.

FBI fingerprint identification automation study. AIDS 3 evaluation report. Volume 4: Economic feasibility

Science.gov (United States)

Mulhall, B. D. L.

1980-01-01

The results of the economic analysis of the AIDS 3 system design are presented. AIDS 3 evaluated a set of economic feasibility measures including life cycle cost, implementation cost, annual operating expenditures and annual capital expenditures. The economic feasibility of AIDS 3 was determined by comparing the evaluated measures with the same measures, where applicable, evaluated for the current system. A set of future work load scenarios was constructed using JPL's environmental evaluation study of the fingerprint identification system. AIDS 3 and the current system were evaluated for each of the economic feasibility measures for each of the work load scenarios. They were compared for a set of performance measures, including response time and accuracy, and for a set of cost/benefit ratios, including cost per transaction and cost per technical search. Benefit measures related to the economic feasibility of the system are also presented, including the required number of employees and the required employee skill mix.

Bin Set 1 Calcine Retrieval Feasibility Study

International Nuclear Information System (INIS)

Adams, R.D.; Berry, S.M.; Galloway, K.J.; Langenwalter, T.A.; Lopez, D.A.; Noakes, C.M.; Peterson, H.K.; Pope, M.I.; Turk, R.J.

1999-01-01

At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase

Bin Set 1 Calcine Retrieval Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

R. D. Adams; S. M. Berry; K. J. Galloway; T. A. Langenwalter; D. A. Lopez; C. M. Noakes; H. K. Peterson; M. I. Pope; R. J. Turk

1999-10-01

At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase.

Feasibility studies of colorless LR 115 SSNTD for alpha-particle radiobiological experiments

International Nuclear Information System (INIS)

Chan, K.F.; Tse, A.K.W.; Fong, W.F.; Yu, K.N.

2006-01-01

The feasibility of using the active layer of the colorless LR 115 SSNTD for alpha-particle radiobiological experiments was studied. The track revelation time on the bottom side (the side attached to the polyester base) was much longer than that on the top side (the side not attached to the polyester base) of the active layer so track formation on the top side was more desirable. In relation to this, culture of HeLa cells on the bottom side of the active layer was found feasible although the cultured cell number was relatively smaller. The feasibility of using this SSNTD for alpha-particle radiobiological experiments was demonstrated by culturing cells on the bottom side while performing alpha-particle irradiation and chemical etching on the top side, and by taking photographs of the cells and alpha-particle tracks together under the optical microscope

Results of a downhole formation microscanner study in a Juro-Triassic-aged sedimentary deposit (Passaic Formation)

International Nuclear Information System (INIS)

Fischer, J.A.; Fischer, J.J.; Bullwinkel, R.J.

1994-01-01

Studies to determine the structural and geohydrological properties of the Passaic Formation were performed at two sites. Both sites are located in northeastern New Jersey, within the Juro-Triassic-aged Newark Basin. The Passaic Formation rocks are described in the literature as a reddish brown, thin to massively bedded, sedimentary deposit with lithology ranging from claystone through conglomerate. A fractured open-quotes layer cakeclose quotes model has been proposed (and is generally accepted) to describe the prevailing geohydrological conditions. The Formation MicroScanner tool was used in four wells drilled for these projects (two at each site). In addition to this microresistivity tool, a suite of other oil field geophysical tools (Gamma, Induction, Dipmeter, Temperature, and Neutron probes) were also utilized. The data collected with the Formation MicroScanner were correlated with detailed logs and the continuous core retrieved from three of the wells. Pump test data was also obtained at both sites. The geophysical data obtained at both sites allowed the direct identification of fractures and their orientation in relation to bedding. Fracture and bedding aperture size and orientation were measured. The results, as presented in this paper, show a high degree of inhomogeneity at both sites rather than the conventional layer cake model. For appropriate site analyses it was necessary to significantly refine the previously assumed Passaic Formation geohydrological and structural model. 14 refs., 4 figs

Coeur d'Alene Tribe Energy Efficiency Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Allgood, Tiffany L. [Coeur d' Alene Tribe, Plummer, ID (United States); Sorter, Andy [Coeur d' Alene Tribe, Plummer, ID (United States)

2014-09-01

The Coeur d'Alene Tribe's Energy Efficiency Feasibility Study (EEFS) is the culminating document that compiles the energy efficiency and building performance assessment and project prioritization process completed on 36 Tribally owned and operated facilities within Tribal lands. The EEFS contains sections on initial findings, utility billing analyses, energy conservation measures and prioritization and funding sources and strategies for energy project implementation.

Feasibility study report for Operable Unit 4: Fernald Environmental Management Project, Fernald, Ohio: Remedial investigation and feasibility study: Volume 3: Final report

International Nuclear Information System (INIS)

1994-02-01

This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP. This volume contains appendices F--J

[Feasibility study for whole plant medicinal use of Tribulus terrestris].

Science.gov (United States)

Yang, Li; Wang, Chunyu; Han, Meiw; Yang, Limin

2009-09-01

The content differences of leaf, plant and fruit of Tribulus terrestris was compared to study the feasibility of whole plant medicinal use. The samples were collected in three typical habitats and six different production areas of T. terrestris. The main medicinal ingredients saponins and flavonoids were determined in root, stem, leaf and fruit during the harvest time. The two ingredients were abounded in leaf and more than 2.61 times as in other parts of the plant. The results showed that there were no differences between the whole plant and the fruit. It should pay more attentions on the collection, preservation and utilization of the leaf of T. terrestris in the harvesting and processing stage. The whole plant for medical use was feasibility based on the content of the ingredients.

Online Recruitment: Feasibility, Cost, and Representativeness in a Study of Postpartum Women.

Science.gov (United States)

Leach, Liana S; Butterworth, Peter; Poyser, Carmel; Batterham, Philip J; Farrer, Louise M

2017-03-08

Online recruitment is feasible, low-cost, and can provide high-quality epidemiological data. However, little is known about the feasibility of recruiting postpartum women online, or sample representativeness. The current study investigates the feasibility of recruiting a population of postpartum women online for health research and examines sample representativeness. Two samples of postpartum women were compared: those recruited online as participants in a brief survey of new mothers (n=1083) and those recruited face-to-face as part of a nationally representative study (n=579). Sociodemographic, general health, and mental health characteristics were compared between the two samples. Obtaining a sample of postpartum women online for health research was highly efficient and low-cost. The online sample over-represented those who were younger (aged 25-29 years), were in a de facto relationship, had higher levels of education, spoke only English at home, and were first-time mothers. Members of the online sample were significantly more likely to have poor self-rated health and poor mental health than the nationally representative sample. Health differences remained after adjusting for sociodemographic differences. Potential exists for feasible and low-cost e-epidemiological research with postpartum populations; however, researchers should consider the potential influence of sample nonrepresentativeness. ©Liana S Leach, Peter Butterworth, Carmel Poyser, Philip J Batterham, Louise M Farrer. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 08.03.2017.

Preliminary geohydrologic conceptual model of the Los Medanos region near the Waste Isolation Pilot Plant for the purpose of performance assessment

International Nuclear Information System (INIS)

Brinster, K.F.

1991-01-01

This report describes a geohydrologic conceptual model of the northern Delaware Basin to be used in modeling three-dimensional, regional ground-water flow for assessing the performance of the Waste Isolation Pilot Plant (WIPP) in the Los Medanos region near Carlsbad, New Mexico. Geochemical and hydrological evidence indicates that flow is transient in the Rustler Formation and the Capitan aquifer in response to changing geologic, hydrologic, and climatic conditions. Before the Pleistocene, ground-water flow in the Rustler Formation was generally eastward, but uneven tilting of the Delaware Basin lowered the regional base level and formed fractures in the evaporitic sequence of rocks approximately parallel to the basin axis. Dissolution along the fractures, coupled with erosion, formed Nash Draw. Also, the drop in base level resulted in an increase in the carrying power of the Pecos River, which began incising the Capitan/aquifer near Carlsbad, New Mexico. Erosion and downcutting released hydraulic pressure that caused a reversal in Rustler ground-water flow direction near the WIPP. Flow in the Rustler west of the WIPP is toward Nash Draw and eventually toward Malaga Bend; flow south of the WIPP is toward Malaga Bend. 126 refs., 70 figs., 18 tabs

GIS development to monitor climate change and its geohydrological consequences on non-monsoon crop pattern in Himalaya

Science.gov (United States)

Rawat, Pradeep K.

2014-09-01

The main objective of the study was to assess climate change and its geohydrological impacts on non-monsoon crop pattern at watershed level through GIS development on climate informatics, land use informatics, hydro-informatics and agro-informatics. The Dabka watershed constitutes a part of the Kosi Basin in densely populated Lesser Himalaya, India in district Nainital has been selected for the case illustration. This reconnaissance study analyzed the climatic database for last three decades (1982-2012) and estimates that the average temperature and evaporation loss have been rising with the rate of 0.07 °C/yr and 4.03 mm/yr respectively whereas the average rainfall has been decreasing with the rate of 0.60 mm/yr. These rates of climate change increasing with mounting elevations. Consequently the existing microclimatic zones (sub-tropical, temperate and moist temperate) shifting towards higher altitudes and affecting the favorable conditions of the land use pattern and decreased the eco-friendly forest and vegetation cover. The land use degradation and high rate of deforestation (0.22 km2 or 1.5%/yr) leads to accelerate several hydrological problems during non-monsoon period (i.e. decreasing infiltration capacity of land surface, declining underground water level, drying up natural perennial springs and streams, decreasing irrigation water availability etc.). In order to that the non-monsoon crops yield has been decreasing with the rate of 0.60% each year as the results suggest that the average crop yield is just about 58 q/ha whereas twenty five to thirty year back it was recorded about 66 q/ha which is about 12% higher (8 q/ha) than existing yield. On the other hand the population increasing with the growth rate of 2% each year. Therefore, decreasing crop yield and increasing population raised food deficiency problem and the people adopting other occupations which ultimately affecting rural livelihood of the Himalaya.

Feasibility study for Boardman River hydroelectric power. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1979-02-22

The feasibility of generating additional hydroelectric power from five consecutive existing dams located on the Boardman River in Grand Traverse County and Traverse City, Michigan, was investigated. The potential hydropower production capabilities, in terms of base load power and peak load power, the legal-institutional-environmental constraints, and the economic feasibility, including capital investment, operating costs and maintenance costs, were evaluated for each of the five dam sites individually and as a series of co-dependent facilities. The impact of installing fish passages at each site was analyzed separately. The feasibility assessment utilized the present worth analytical method, considering revenue based on thirty mills/kWh for power, 0.4% general economy escalation rate, and a 6% net income to the municipal utility. The sensitivity of fuel costs increasing at a different rate than the general price-escalation was tested by allowing the increase in fuel costs to vary from 3 to 8% per year. Assuming fuel costs increase at the same rate as the general economy, it is feasible to update, retrofit, renovate, and install hydroelectric generating capacity at Sabin, Boardman and Brown Bridge. Rehabilitation of Union Street and Keystone is also feasible but somewhat less attractive. Operating the dams as a co-dependent system has environmental advantages and can provide additional revenue through peak load power rates. A development plan to implement the above is outlined utilizing an ownership arrangement whereby Grand Traverse County provides easements for Sabin and Boardman Dams. The plan calls for operation of the system by Traverse City.

Evaluation of geohydrologic framework, recharge estimates and ground-water flow of the Joshua Tree area, San Bernardino County, California

Science.gov (United States)

Nishikawa, Tracy; Izbicki, John A.; Hevesi, Joseph A.; Stamos, Christina L.; Martin, Peter

2005-01-01

Ground water historically has been the sole source of water supply for the community of Joshua Tree in the Joshua Tree ground-water subbasin of the Morongo ground-water basin in the southern Mojave Desert. The Joshua Basin Water District (JBWD) supplies water to the community from the underlying Joshua Tree ground-water subbasin. The JBWD is concerned with the long-term sustainability of the underlying aquifer. To help meet future demands, the JBWD plans to construct production wells in the adjacent Copper Mountain ground-water subbasin. As growth continues in the desert, there may be a need to import water to supplement the available ground-water resources. In order to manage the ground-water resources and to identify future mitigating measures, a thorough understanding of the ground-water system is needed. The purpose of this study was threefold: (1) improve the understanding of the geohydrologic framework of the Joshua Tree and Copper Mountain ground-water subbasins, (2) determine the distribution and quantity of recharge using field and numerical techniques, and (3) develop a ground-water flow model that can be used to help manage the water resources of the region. The geohydrologic framework was refined by collecting and interpreting water-level and water-quality data, geologic and electric logs, and gravity data. The water-bearing deposits in the Joshua Tree and Copper Mountain ground-water subbasins are Quarternary alluvial deposits and Tertiary sedimentary and volcanic deposits. The Quarternary alluvial deposits were divided into two aquifers (referred to as the 'upper' and the 'middle' alluvial aquifers), which are about 600 feet (ft) thick, and the Tertiary sedimentary and volcanic deposits were assigned to a single aquifer (referred to as the 'lower' aquifer), which is as thick as 1,500 ft. The ground-water quality of the Joshua Tree and Copper Mountain ground-water subbasins was defined by collecting 53 ground-water samples from 15 wells (10 in the

A guideline to study the feasibility domain of multi-trophic and changing ecological communities.

Science.gov (United States)

Song, Chuliang; Rohr, Rudolf P; Saavedra, Serguei

2018-04-24

The feasibility domain of an ecological community can be described by the set of environmental abiotic and biotic conditions under which all co-occurring and interacting species in a given site and time can have positive abundances. Mathematically, the feasibility domain corresponds to the parameter space compatible with positive (feasible) solutions at equilibrium for all the state variables in a system under a given model of population dynamics. Under specific dynamics, the existence of a feasible equilibrium is a necessary condition for species persistence regardless of whether the feasible equilibrium is dynamically stable or not. Thus, the size of the feasibility domain can also be used as an indicator of the tolerance of a community to random environmental variations. This has motivated a rich research agenda to estimate the feasibility domain of ecological communities. However, these methodologies typically assume that species interactions are static, or that input and output energy flows on each trophic level are unconstrained. Yet, this is different to how communities behave in nature. Here, we present a step-by-step quantitative guideline providing illustrative examples, computational code, and mathematical proofs to study systematically the feasibility domain of ecological communities under changes of interspecific interactions and subject to different constraints on the trophic energy flows. This guideline covers multi-trophic communities that can be formed by any type of interspecific interactions. Importantly, we show that the relative size of the feasibility domain can significantly change as a function of the biological information taken into consideration. We believe that the availability of these methods can allow us to increase our understanding about the limits at which ecological communities may no longer tolerate further environmental perturbations, and can facilitate a stronger integration of theoretical and empirical research. Copyright �

Muon muon collider: Feasibility study

International Nuclear Information System (INIS)

1996-01-01

A feasibility study is presented of a 2 + 2 TeV muon collider with a luminosity of L = 10 35 cm -2 s -1 . The resulting design is not optimized for performance, and certainly not for cost; however, it does suffice--the authors believe--to allow them to make a credible case, that a muon collider is a serious possibility for particle physics and, therefore, worthy of R and D support so that the reality of, and interest in, a muon collider can be better assayed. The goal of this support would be to completely assess the physics potential and to evaluate the cost and development of the necessary technology. The muon collider complex consists of components which first produce copious pions, then capture the pions and the resulting muons from their decay; this is followed by an ionization cooling channel to reduce the longitudinal and transverse emittance of the muon beam. The next stage is to accelerate the muons and, finally, inject them into a collider ring which has a small beta function at the colliding point. This is the first attempt at a point design and it will require further study and optimization. Experimental work will be needed to verify the validity of diverse crucial elements in the design

Industrial feasibility study of a spent nuclear fuel package for direct deep disposal

International Nuclear Information System (INIS)

Le Lous, K.; Loubrieu, J.; Chupeau, J.; Serpantie, J.P.; Becle, D.; Aubry, S.

2001-01-01

EDF has undertaken to study the industrial feasibility of a spent nuclear fuel package meeting direct disposal requirements. In this context, a disposal concept has been defined in which packages are cooled in place until the module is finally sealed. Indeed, one of the objectives of that disposal concept is to reduce the underground area occupied by the repository. A functional analysis has been performed within the framework of that ventilated disposal concept, taking into account the phases of the package lifetime from its conditioning until the disposal post-closure phase. An industrial feasibility study is in progress, which takes into account the functional specifications and some preliminary studies. (author)

Feasibility study of gamma-ray medical radiography

International Nuclear Information System (INIS)

Alyassin, Abdalmajeid M.; Maqsoud, Hamza A.; Mashat, Ahmad M.; Al-Mohr, Al-Sayed; Abdulwajid, Subhan

2013-01-01

This research explores the feasibility of using gamma-ray radiography in medical imaging. We will show that gamma-ray medical radiography has the potential to provide alternative diagnostic medical information to X-ray radiography. Approximately one Ci Am-241 radioactive source which emits mono-energetic 59.5 keV gamma rays was used. Several factors that influence the feasibility of this study were tested. They were the radiation source uniformity, image uniformity, and image quality parameters such as contrast, noise, and spatial resolution. In addition, several gamma-ray and X-ray images were acquired using humanoid phantoms. These images were recorded on computed radiography image receptors and displayed on a standard monitor. Visual assessments of these images were then conducted. The Am-241 radioactive source provided relatively uniform radiation exposure and images. Image noise and image contrast were mainly dependent on the exposure time and source size, whereas spatial resolution was dependent on source size and magnification factor. The gamma-ray humanoid phantom images were of lower quality than the X-ray images mainly due to the low radioactivity used and not enough exposure time. Nevertheless, the gamma-ray images displayed most of the main structures contained in the humanoid phantoms. Higher exposure rates and thus lower exposure times were estimated for different pure Am-241 source sizes that are hypothesized to provide high quality images similar to X-ray images. For instance, a 10 mm source size of pure Am-241 with 7 s exposure time should produce images similar in contrast and noise to X-ray images. This research paves the way for the production and usage of a highly radioactive Am-241 source with the potential to lead to the feasibility of acceptable quality medical gamma-ray radiography. - Highlights: ► Characterized the performance of gamma-ray radiography. ► Displayed medical images of humanoid phantoms using gamma radiography. ► Am-241

Knee ultrasound from research to real practice: a systematic literature review of adult knee ultrasound assessment feasibility studies.

Science.gov (United States)

Peltea, Alexandra; Berghea, Florian; Gudu, Tania; Ionescu, Ruxandra

2016-12-05

To identify and analyse existing data regarding knee ultrasound (US) feasibility in clinical practice. Material and methods: A systematic literature review was performed using the terms: ("knee") AND ("ultrasound" OR "ultrasonography") AND ("feasibility" OR "pilot" OR "proof of concept"). Feasibility studies regarding knee US or US aided maneuver involving knee joint, published during 2005-2015, were selected and evaluated against a complex framework constructed around mandatory key areas for feasibility studies: acceptability, demand, implementation, practicality, adaptation, integration and expansion. One hundred and fifty-nine publications were identified, of which 9 were included in the final analysis: 6 dealt with the development and implementation of novel US scores, while the rest focused on implementing MSUS in clinical practice, evaluating the usefulness of articular cartilage US assessment and the feasibility of sonography for intra-articular knee injections, respectively. Six studies quantified feasibility as time spent for the evaluation, with only two addressing areassuch as acceptability, implementation and practicality, although none of these systematically assessed all feasibility domains. Knee US feasibility is still poorly addressed; the time required for US assessment is the main area addressed. This information gap should be properly addressed in future works, in order to ensure the right place for this technique.

Feasibility study of utilizing solar furnace technology in steel making industry

Energy Technology Data Exchange (ETDEWEB)

Abbaspoursani, K. [The Faculty of Mechanical Engineering, Takestan Islamic Azad University (Iran, Islamic Republic of)], Email: a.abbaspour@tiau.ac.ir; Tofigh, A.A.; Nahang Toudeshki, S.; Hadadian, A. [Department of Energy, Materials and Energy Research Center (Iran, Islamic Republic of)], Email: Ali.A.Tofigh@gmail.com, email: toudeshki@hotmail.com, email: Arash.Hadadian@gmail.com; Farahmandpour, B. [Iranian Fuel Conservation company (Iran, Islamic Republic of)], Email: farahmandpour@gmail.com

2011-07-01

In Iran, the casting industry consumes 33.6% of electricity production, and most of this electricity is used in the melting process. Currently, scrap preheating is done using electric arc furnaces and the aim of this study is to assess the feasibility of replacing electric arc furnaces with solar furnaces. The performance of solar furnaces in the Iran Alloy Steel Company under Yazd climate conditions was studied. It was found that the solar irradiation time and solar insulation are sufficient to operate a solar furnace with the capacity to preheat 250 thousand tons per year of scrap to 500 degrees celsius. Results showed that such a furnace would decrease energy consumption by 40 GWh per year and that it would take 5 years to return the investment. This study demonstrated that operating a solar furnace in the Iran Alloy Steel Company under Yazd climate conditions is feasible and would result in economic and environmental benefits.

Pyrolysis in Groningen, Netherlands. Feasibility study on a transition coalition

International Nuclear Information System (INIS)

Siemons, R.V.

2005-01-01

Results of a study on the technical, economical and financial feasibility of a pyrolysis factory for the processing and energetic application of biomass wastes in the Dutch province Groningen are presented and discussed. Also, attention is paid to the implementation of the planned pyrolysis factory in one or more transition programmes. [nl

Feasibility and Accuracy of Digitizing Edentulous Maxillectomy Defects: A Comparative Study.

Science.gov (United States)

Elbashti, Mahmoud E; Hattori, Mariko; Patzelt, Sebastian Bm; Schulze, Dirk; Sumita, Yuka I; Taniguchi, Hisashi

The aim of this study was to evaluate the feasibility and accuracy of using an intraoral scanner to digitize edentulous maxillectomy defects. A total of 20 maxillectomy models with two defect types were digitized using cone beam computed tomography. Conventional and digital impressions were made using silicone impression material and a laboratory optical scanner as well as a chairside intraoral scanner. The 3D datasets were analyzed using 3D evaluation software. Two-way analysis of variance revealed no interaction between defect types and impression methods, and the accuracy of the impression methods was significantly different (P = .0374). Digitizing edentulous maxillectomy defect models using a chairside intraoral scanner appears to be feasible and accurate.

ADHD and EEG-neurofeedback: a double-blind randomized placebo-controlled feasibility study

NARCIS (Netherlands)

Lansbergen, M.M.; Dongen-Boomsma, M. van; Buitelaar, J.K.; Slaats-Willemse, D.I.E.

2011-01-01

Electroencephalography (EEG)-neurofeedback has been shown to offer therapeutic benefits to patients with attention-deficit/hyperactivity disorder (ADHD) in several, mostly uncontrolled studies. This pilot study is designed to test the feasibility and safety of using a double-blind placebo

An exploratory shaft facility in SALT: Draft shaft study plan

International Nuclear Information System (INIS)

1987-03-01

This draft Shaft Study Plan describes a program of testing and monitoring in the Exploratory Shafts of a candidate high-level nuclear waste repository site in Deaf Smith County, Texas. The purpose of the programs to assist with site characterization in support of a determination of site suitability for development as a repository design and performance assessment evaluations. The program includes a variety of geological, geophysical, geomechanical, thermomechanical, and geohydrological testing and monitoring. The program is presented as a series of separate studies concerned with geological, geomechanical, and geohydrological site characterization, and with evaluating the mechanical and hydrological response of the site to construction of the shafts. The various studies, and associated test or monitoring methods are shown. The procedure used in developing the test program has been to initially identify the information necessary to satisfy (1) federal, state, and local requirements, and (2) repository program requirements. These information requirements have then been assessed to determine which requirements can be addressed wholly or in significant part by monitoring and testing from within the shafts. Test methods have been identified to address specific information requirements. 67 refs., 39 figs., 31 tabs

Trans-Caspian gas pipeline feasibility study. Volume 3

International Nuclear Information System (INIS)

1999-01-01

This study, conducted by Enron Engineering and Construction Company, was funded by the US Trade and Development Agency. The study provides detailed information concerning natural gas demand in Turkey and Southern Europe. The purpose of the study is to estimate the rate at which new gas can be absorbed in the Turkish market and be re-exported to the markets in Europe, as well as to forecast Turkish natural gas demand for the period up to 2020. The study also evaluates gas demand and pricing for the market in the 2002--2005 time frame. This is Volume 3 of a 3-volume report, and it is divided into the following sections: (1) Executive Summary; (2) Task C: Technical Feasibility and Preliminary Design; (3) Task F: Project Implementation Strategy

Feasibility study report for Operable Unit 4: Volume 2

International Nuclear Information System (INIS)

1994-02-01

This report documents the Feasibility Study (FS) phase of the Fernald Environmental Management Project (FEMP) Operable Unit 4 Remedial Investigation/Feasibility Study (RI/FS) Program. The FEMP, formerly known as the Feed Materials Production Center (FMPC), is a US Department of Energy (DOE) facility that operated from 1952 to 1989. The facility's primarily function was to provide high purity uranium metal products to support United States defense programs. Production operations were suspended in 1989 to focus on environmental restoration and waste management activities at the facility. The RI/FS is being conducted pursuant to the terms of a Consent Agreement between DOE and the US Environmental Protection Agency (EPA) under Sections 120 and 106(a) of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), as amended. The Ohio Environmental Protection Agency (OEPA) is also participating in the RI/FS process at the FEMP through direct involvement in program review meetings and technical review of project documentation. The objective of the RI/FS process is to gather information to support an informed risk management decision regarding which remedy appears to be the most appropriate action for addressing the environmental concerns identified at the FEMP. This volume contains appendices A--E

Feasibility Study for Cobalt Bundle Loading to CANDU Reactor Core

International Nuclear Information System (INIS)

Park, Donghwan; Kim, Youngae; Kim, Sungmin

2016-01-01

CANDU units are generally used to produce cobalt-60 at Bruce and Point Lepreau in Canada and Embalse in Argentina. China has started production of cobalt-60 using its CANDU 6 Qinshan Phase III nuclear power plant in 2009. For cobalt-60 production, the reactor’s full complement of stainless steel adjusters is replaced with neutronically equivalent cobalt-59 adjusters, which are essentially invisible to reactor operation. With its very high neutron flux and optimized fuel burn-up, the CANDU has a very high cobalt-60 production rate in a relatively short time. This makes CANDU an excellent vehicle for bulk cobalt-60 production. Several studies have been performed to produce cobalt-60 using adjuster rod at Wolsong nuclear power plant. This study proposed new concept for producing cobalt-60 and performed the feasibility study. Bundle typed cobalt loading concept is proposed and evaluated the feasibility to fuel management without physics and system design change. The requirement to load cobalt bundle to the core was considered and several channels are nominated. The production of cobalt-60 source is very depend on the flux level and burnup directly. But the neutron absorption characteristic of cobalt bundle is too high, so optimizing design study is needed in the future

Feasibility Study for Cobalt Bundle Loading to CANDU Reactor Core

Energy Technology Data Exchange (ETDEWEB)

Park, Donghwan; Kim, Youngae; Kim, Sungmin [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

CANDU units are generally used to produce cobalt-60 at Bruce and Point Lepreau in Canada and Embalse in Argentina. China has started production of cobalt-60 using its CANDU 6 Qinshan Phase III nuclear power plant in 2009. For cobalt-60 production, the reactor’s full complement of stainless steel adjusters is replaced with neutronically equivalent cobalt-59 adjusters, which are essentially invisible to reactor operation. With its very high neutron flux and optimized fuel burn-up, the CANDU has a very high cobalt-60 production rate in a relatively short time. This makes CANDU an excellent vehicle for bulk cobalt-60 production. Several studies have been performed to produce cobalt-60 using adjuster rod at Wolsong nuclear power plant. This study proposed new concept for producing cobalt-60 and performed the feasibility study. Bundle typed cobalt loading concept is proposed and evaluated the feasibility to fuel management without physics and system design change. The requirement to load cobalt bundle to the core was considered and several channels are nominated. The production of cobalt-60 source is very depend on the flux level and burnup directly. But the neutron absorption characteristic of cobalt bundle is too high, so optimizing design study is needed in the future.

Adding evidence-based interventions to assertive community treatment : a feasibility study

NARCIS (Netherlands)

Sytema, Sjoerd; Jörg, Frederike; Nieboer, Roeline; Wunderink, Lex

OBJECTIVE: This 24-month study, conducted in The Netherlands, examined the feasibility of enhancing the effectiveness of assertive community treatment (ACT) by adding evidence-based interventions. METHODS: A total of 159 patients were randomly assigned to two ACT teams, one providing standard ACT

Feasibility studies of radiation sterilization of some pharmaceutical products

International Nuclear Information System (INIS)

Gopal, N.G.S.; Rajagopalan, S.; Sharma, G.

1975-01-01

The paper deals with some studies carried out to evaluate the feasibility of radiation sterilization or treatment of some medical products and pharmaceuticals of immediate importance to their respective industries. The products include penicillin G sodium, ampicillin sodium, tetracyclin hydrochloride ointment,hydrocortisone acetate and its ointment, aqueous sodium chloride solutions (0.9 and 20%), fluorescein sodium strips, urea, ethylmorphine hydrochloride, aqueous solution of chlorobutanol and one of its commercial preparations, phenylmercuric nitrate and its aqueous solutions, aqueous solutions of methyl and propyl paraben, lactose, gum karaya, absorbent cotton and poly-(vinyl chloride) based medical products. The irradiated products have been examined for pharmacopoeial specifications wherever available. In general the products have been examined for changes in colour, pH, ultra-violet and infra-red absorption spectra. Thin-layer chromatographic analyses have been carried out to establish the purity of some of the irradiated products. The feasibility or otherwise of radiation sterilization or treatment of the various products from the physicochemical and microbiological (pharmacological) clinical considerations is also described. (author)

Recruitment and retention of farm owners and workers for a six-month prospective injury study in New Zealand: a feasibility study

Directory of Open Access Journals (Sweden)

Langley John D

2011-05-01

Full Text Available Abstract Background Agricultural workers experience high rates of occupational injury. There is a lack of analytic studies which provide detailed occupational exposure information to inform intervention development. Methods A feasibility study simulating a six month prospective cohort study was designed and undertaken. The levels of farm and worker participation and retention were analysed to determine the feasibility of the methods for wider deployment. Results Recruitment levels were comparable with other studies, with 24% of farms and 36% of non-owner workers participating. Once recruited, retention was high at 85% and 86% respectively. Conclusions The main challenges identified were in the recruitment process. Once recruited, farms and workers tended to complete the study, indicating that prospective studies in this the agricultural workforce may be feasible. Issues encountered and potential solutions for future studies are discussed.

Central repository for low- and intermediate-level waste (ALMA) conceptual design, siting and safety study

International Nuclear Information System (INIS)

Kjellbert, N.; Haeggblom, H.; Cederstroem, M.; Lundgren, T.

1980-07-01

A generic design, siting and safety study of a proposed repository for low- and intermediate-level waste has been made. Special emphasis has been placed on safety characterostics. The conceptual design and the generic site, on which the study is based, are realistically chosen in accordance with present construction techniques and the existing geohydrological conditions in Sweden. (Auth.)

Small modular biopower initiative Phase 1 feasibility studies executive summaries

Energy Technology Data Exchange (ETDEWEB)

Bain, R.

2000-03-06

The Phase 1 objective is a feasibility study that includes a market assessment, resource assessment, preliminary system design, and assessment of relevant environmental and safety considerations, and evaluation of financial and cost issues, and a preliminary business plan and commercialization strategy. Each participating company will share at least 20% of the cost of the first phase.

Pueblo of Jemez Geothermal Feasibility Study Fianl Report

Energy Technology Data Exchange (ETDEWEB)

S.A. Kelley; N. Rogers; S. Sandberg; J. Witcher; J. Whittier

2005-03-31

This project assessed the feasibility of developing geothermal energy on the Pueblo of Jemez, with particular attention to the Red Rocks area. Geologic mapping of the Red Rocks area was done at a scale of 1:6000 and geophysical surveys identified a potential drilling target at a depth of 420 feet. The most feasible business identified to use geothermal energy on the reservation was a greenhouse growing culinary and medicinal herbs. Space heating and a spa were identified as two other likely uses of geothermal energy at Jemez Pueblo. Further geophysical surveys are needed to identify the depth to the Madera Limestone, the most likely host for a major geothermal reservoir.

Biogas Koczala. Biogas project in Koczala. Feasibility study. Technical report

International Nuclear Information System (INIS)

2004-08-01

The present production of district heating in Koczala is based on coal. The district heating system is worn out technically and economically and according to the 2001 Energy Plan of Koczala the district heating plant shall be converted to a combination of a biogas fired CHP and a wood chip boiler. The overall objective of this project is to access the feasibility and viability construction an operation of a biogas plant owned by the co-operative agricultural company, Poldanor S.A. The feasibility study includes: 1) Availability of organic waste in the Koczala area, 2) Possibilities of using energy crops in the biogas plant, 3) Possibilities of receiving grants from the Polish National Fund for Environmental Protection, the new EU regional funds and through the joint implementation market (CO 2 quotas), 4) Alternative locations of the biogas plant and the CHP unit, 5) Alternative strategies for selling electricity and heat, 6) Organisational issues (ownership). This report concludes that implementing the biogas project is environmentally and financially feasible and viable. If organic waste and/or maize silage can be provided and gasified without problems, the plant can supply as well the Koczala farm as the fodder mill with steam and heat, and also supply Koczala district heating system with approx. 75% of yearly heat consumption. Furthermore, electricity is supplied to the fodder mill and the public grid. (BA)

Geohydrology of the Island of Oahu, Hawaii

Science.gov (United States)

Hunt, Charles D.

1996-01-01

may drive geothermal convection of freshwater in the rift zones. Saltwater flow is driven by changes in freshwater volume and sea level and by dispersive and geothermal convection. Freshwater flow is much more active--velocity is higher and residence time is shorter--than saltwater flow. Hydrodynamic dispersion produces a transition zone of mixed water between the freshwater and the underlying saltwater. The Waianae aquifer in the Waianae Volcanics and the Koolau aquifer in the Koolau Basalt are the two principal volcanic-rock aquifers on Oahu. The sequences of coastal-plain and valley-fill deposits locally form aquifers, but these aquifers are of minor importance because of the small volume of water contained in them. The two principal volcanic-rock aquifers are composed mainly of thick sequences of permeable, thin-bedded lava flows. These aquifers combine to form a layered aquifer system throughout central Oahu where the Koolau aquifer overlies the Waianae aquifer. They are separated by a regional confining unit formed by weathering along the Waianae-Koolau unconformity, which marks the eroded and weathered surface of the Waianae Volcano buried by younger Koolau lava flows. The areal hydraulic continuity of the aquifers of Oahu is interrupted in many places by steeply dipping, stratigraphically unconformable, geohydrologic barriers. These low-permeability features include eruptive feeder dikes, sedimentary valley fills, and former erosional surfaces now buried by younger lava flows or sediments. The barriers impede and divert lateral ground-water flow and impound ground water to greater heights than would occur in the absence of the barriers, causing abrupt stepped discontinuities in the potentiometric surface. The largest discontinuities are associated with dense concentrations of dikes in the eruptive rift zones of each volcano. The dikes in these zones originate from great depths and impede flow both in shallow-freshwater and in deep-saltwater flow sy

Current status of feasibility studies on commercialized fuel cycle system for Fast Breeder Reactor

International Nuclear Information System (INIS)

Ojima, Hisao; Nagaoki, Yoshihiro

2000-01-01

A 'Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' is underway at the Japan Nuclear Cycle Development Institute (JNC). The study will select the promising concepts with their R and D tasks in order to commercialize the fast breeder reactor (FBR) cycle system. The feasibility studies (F/S) have to present surveyed and screened various relevant technologies, and defined the design requirement of the commercialized fuel cycle system for FBR. The promising technical options are being evaluated and conceptual designs are being examined. At the end of JFY2000, several candidate concepts of the commercialized FBR cycle system will be proposed. (author)

Muon muon collider: Feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-18

A feasibility study is presented of a 2 + 2 TeV muon collider with a luminosity of L = 10{sup 35} cm{sup {minus}2} s{sup {minus}1}. The resulting design is not optimized for performance, and certainly not for cost; however, it does suffice--the authors believe--to allow them to make a credible case, that a muon collider is a serious possibility for particle physics and, therefore, worthy of R and D support so that the reality of, and interest in, a muon collider can be better assayed. The goal of this support would be to completely assess the physics potential and to evaluate the cost and development of the necessary technology. The muon collider complex consists of components which first produce copious pions, then capture the pions and the resulting muons from their decay; this is followed by an ionization cooling channel to reduce the longitudinal and transverse emittance of the muon beam. The next stage is to accelerate the muons and, finally, inject them into a collider ring which has a small beta function at the colliding point. This is the first attempt at a point design and it will require further study and optimization. Experimental work will be needed to verify the validity of diverse crucial elements in the design.

Sealed source and device removal and consolidation feasibility study

International Nuclear Information System (INIS)

Ward, J.E.; Carter, J.G.; Meyers, R.L.

1993-02-01

The purpose of this study is to assess the feasibility of removing Greater-Than-Class C (GTCC) sealed sources from their containment device and consolidating them for transport to a storage or disposal facility. A sealed source is a sealed capsule containing a radioactive material that is placed in a device providing radioactive containment. It is used in the medical, industrial, research, and food-processing communities for calibrating, measuring, gauging, controlling processes, and testing. This feasibility study addresses the key operational, safety, regulatory, and financial requirements of the removal/consolidation process. This report discusses the process to receive, handle, repackage, and ship these sources to an interim or dedicated storage facility until a final disposal repository can be built and become operational (∼ c. 2010). The study identifies operational and facility requirements to perform this work. Hanford, other DOE facilities, and private hot-cell facilities were evaluated to determine which facilities could perform this work. The personnel needed, design and engineering, facility preparation, process waste disposal requirements, and regulatory compliance were evaluated to determine the cost to perform this work. Cost requirements for items that will have to meet future changing regulatory requirements for transportation, transportation container design and engineering, and disposal were not included in this study. The cost associated with in-process consolidation of the sealed sources reported in this study may have not been modified for inflation and were based on 1992 dollars. This study shows that sealed source consolidation is possible with minimal personnel exposure, and would reduce the risk of radioactive releases to the environment. An initial pilot-scale operation could evaluate the possible methods to reduce the cost and consolidate sources

Feasibility studies for alpha waste disposal on geological formations in France

International Nuclear Information System (INIS)

Jaouen, C.; Boulanger, A.

1986-01-01

Since 1977, SGN has been involved in many feasibility studies and consultant works in the fields of HLW storages. Starting as nuclear consultant company in the KBS review of the long term storage of HLW, SGN and GEOSTOCK were entrusted in 1978 by the EEC for the basic design and evaluation of the deep storage into granite rock of HLW, followed by a participation in the thermal sensitivity study of such a storage. The cooperation with GEOSTOCK was first extended in 1981 to a preliminary study of HLW storage conditions in granite for a Japanese company, and then in France for several feasibility studies of HLW and TRU waste geological disposal. Three kinds of scenarios have been forecasted and evaluated in the case of vitrified HLW storage, allowing the thermal power to be decreased and the whole management scheme to be optimized. More recently, SGN participation to French engineering studies has been extended by ANDRA to the TRU waste repository evaluation. All these works for French authorities have been performed in a close connection with several specialized departments in the CEA group, and with the help of geological specialists, under the leadership of ANDRA [fr

Feasibility studies for alpha waste disposal on geological formations in France

International Nuclear Information System (INIS)

Jaouen, C.; Boulanger, A.

1985-01-01

Since 1977, SGN has been involved in many feasibility studies and consultant works in the fields of HLW storages. Starting as nuclear consultant company in the KBS review of the long term storage of HLW, SGN and Geostock were entrusted in 1978 by the EEC for the basic design and evaluation of the deep storage into granite rock of HLW, followed by a participation in the thermal sensitivity study of such a storage. The cooperation with Geostock was first extended in 1981 to a preliminary study of HLW storage conditions in granite for a Japanese company, and then in France for several feasibility studies of HLW and TRU waste geological disposal. Three kinds of scenarios have been forecasted and evaluated in the case of vitrified HLW storage, allowing the thermal power to be decreased and the whole management scheme to be optimized. More recently, SGN participation to French engineering studies has been extended by ANDRA to the TRU waste repository evaluation. All these works for French authorities have been performed in a close connection with several specialized departments in the CEA group, and with the help of geological specialists, under the leadership of ANDRA [fr

Technical Feasibility Study for Zero Energy K-12 Schools

Energy Technology Data Exchange (ETDEWEB)

Bonnema, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldwasser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Torcellini, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pless, Shanti [National Renewable Energy Lab. (NREL), Golden, CO (United States); Studer, Daniel [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-11-01

This technical feasibility study provides documentation and research results supporting a possible set of strategies to achieve source zero energy K-12 school buildings as defined by the U.S. Department of Energy (DOE) zero energy building (ZEB) definition (DOE 2015a). Under this definition, a ZEB is an energy-efficient building in which, on a source energy basis, the actual annual delivered energy is less than or equal to the on-site renewable exported energy.

Pascua Yaqui Tribe Renewable Energy Development and Deployment Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Arvayo, Maria

2014-05-30

In 2012, PYT was awarded a grant from the Department of Energy Tribal Energy Program to conduct a Renewable Energy Development and Deployment Feasibility Study that would define the technical and economic viability of renewable energy on tribal lands. Red Mountain Energy Partners (RMEP) was hired by PYT to complete the study. Through this study, Red Mountain concluded that there are viable opportunities for solar at Tortuga Ranch, the Casino del Sol and a third site near the Justice Center on Camino de Oeste.

3D-Flow processor for a programmable Level-1 trigger (feasibility study)

International Nuclear Information System (INIS)

Crosetto, D.

1992-10-01

A feasibility study has been made to use the 3D-Flow processor in a pipelined programmable parallel processing architecture to identify particles such as electrons, jets, muons, etc., in high-energy physics experiments

Kundalini yoga as mutual recovery: a feasibility study including children in care and their carers

OpenAIRE

Perez, Elvira; Ball, Mark; Brown, Poppy; Crepaz-Keay, David; Haslam-Jones, Emily; Crawford, Paul

2016-01-01

This is a mixed-methods feasibility study to test whether incorporating a 20-week Kundalini yoga program into a children’s home community improves wellbeing outcomes. Feasibility was assessed through recruitment and retention rates as well as participants’ self-report perceptions on social inclusion, mental health, wellbeing and semi-structured interviews on the benefits of the study. Mutual recovery entailed that children in care (CiC), youth practitioners, and management participated togeth...

A feasibility study of magnetic resonance imaging of silicone breast implants in Finland

DEFF Research Database (Denmark)

Kulmala, Ilona; Boice, John D; McLaughlin, Joseph K

2005-01-01

to determine the feasibility of conducting a magnetic resonance imaging (MRI)-based study of rupture incidence. The pilot investigation included a clinical examination by a plastic surgeon, MRI scan, and self-administered questionnaire. The participation rate was 100%. Implants in our study represented a cross...... the other diagnosed all implants as intact. The procedures of the feasibility study proved successful, and the results demonstrate the importance of a rigid image evaluation protocol with employment of well-defined rupture criteria, as well as the benefits of several image readers.......Cosmetic breast implants have become increasingly popular throughout the world. However, there is insufficient knowledge about the frequency and severity of local complications such as rupture and capsular contracture. A pilot study of 25 Finnish women with 50 cosmetic breast implants was organized...

Feasibility Study for Operable Unit 7-13/14

International Nuclear Information System (INIS)

K. Jean Holdren Thomas E. Bechtold Brian D. Preussner

2007-01-01

The Subsurface Disposal Area is a radioactive waste landfill located within the Radioactive Waste Management Complex at the Idaho National Laboratory Site in southeastern Idaho. This Feasibility Study for Operable Unit 7-13/14 analyzes options for mitigating risks to human health and the environment associated with the landfill. Analysis is conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act, using nine evaluation criteria to develop detailed and comparative analysis of five assembled alternatives. Assembled alternatives are composed of discrete modules. Ultimately, decision-makers will select, recombine, and sum various modules into an optimized preferred alternative and final remedial decision

Feasibility Study for Operable Unit 7-13/14

Energy Technology Data Exchange (ETDEWEB)

K. Jean Holdren

2007-05-29

The Subsurface Disposal Area is a radioactive waste landfill located within the Radioactive Waste Management Complex at the Idaho National Laboratory Site in southeastern Idaho. This Feasibility Study for Operable Unit 7-13/14 analyzes options for mitigating risks to human health and the environment associated with the landfill. Analysis is conducted in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act, using nine evaluation criteria to develop detailed and comparative analysis of five assembled alternatives. Assembled alternatives are composed of discrete modules. Ultimately, decision-makers will select, recombine, and sum various modules into an optimized preferred alternative and final remedial decision.

The PHARMS (Patient Held Active Record of Medication Status) feasibility study: a research proposal.

LENUS (Irish Health Repository)

Walsh, Elaine

2018-01-08

Medication errors are a major source of preventable morbidity, mortality and cost and many occur at the times of hospital admission and discharge. Novel interventions (such as new methods of recording medication information and conducting medication reconciliation) are required to facilitate accurate transfer of medication information. With existing evidence supporting the use of information technology and the patient representing the one constant in the care process, an electronic patient held medication record may provide a solution. This study will assess the feasibility of introducing a patient held electronic medication record in primary and secondary care using the Consolidated Framework for Implementation Research (CFIR).This feasibility study is a mixed method study of community dwelling older adult patients admitted to an urban secondary care facility comprising a non-randomised intervention and qualitative interviews with key stakeholders. Outcomes of interest include clinical outcomes and process evaluation.This study will yield insights pertaining to feasibility, acceptability and participation for a more definitive evaluation of the intervention. The study also has the potential to contribute to knowledge of implementation of technology in a healthcare context and to the broader area of implementation science.

Developing a Hypnotic Relaxation Intervention to Improve Body Image: A Feasibility Study.

Science.gov (United States)

Cieslak, Alison; Elkins, Gary; Banerjee, Tanima; Marsack, Jessica; Hickman, Kimberly; Johnson, Alisa; Henry, Norah; Barton, Debra

2016-11-01

To determine the content, feasibility, and best outcome of a mind-body intervention involving self-directed hypnotic relaxation to target body image.
. A five-week, uncontrolled, unblinded feasibility intervention study.
. Behavioral therapy offices in Ann Arbor, Michigan, and Waco, Texas.
. 10 female breast cancer survivors and 1 breast and gynecologic cancer survivor. 
. Adult women with a history of breast and gynecologic cancer and no major psychiatric history were eligible. The intervention included four face-to-face sessions with a research therapist lasting 40-60 minutes, logged home practice, one telephone check-in call at week 5, and one intervention feedback telephone call to complete the study. Descriptive statistics and paired t-tests were used to test feasibility and content validity.
. Stress from body changes as measured by the Impact of Treatment Scale, sexual function as measured by the Female Sexual Function Index, and sexual self-image as measured by the Sexual Self-Schema Scale for women were the variables of interest.
. The intervention content was confirmed. Changes in scores from the baseline to week 5 suggested that stress from body changes decreased and sexual self-schema and function improved during the intervention. Nine of the 11 women were satisfied with the intervention, and all 11 indicated that their body image improved. 
. Hypnotic relaxation therapy shows promise for improving body image and, in doing so, improving sexual health in this population. Additional testing of this intervention is warranted.
. Hypnotic relaxation therapy is feasible to improve body image and sexual health in women diagnosed with cancer and may be an important intervention that could be offered by nurses and other behavioral therapists.

Feasibility study--computerized application of the hazardous material regulations

International Nuclear Information System (INIS)

Ferrada, J.J.; Green, V.M.; Rawl, R.R.

1992-09-01

The feasibility of developing a full expert system for transportation and packaging of hazardous and radioactive materials was initiated within the framework of three subtasks: (1) analysis of commercial packages related to regulation scanning, (2) analysis of computer languages to develop the expert system, and (3) development of expert system prototypes. The strategy to develop the latter subtask was to first,develop modules to capture the knowledge of different areas of transportation and packaging and second, to analyze the feasibility of appending these different modules in one final full package. The individual modules development contemplated one prototype for transporting and packaging of radioactive material and another for transporting hazardous chemical materials. In the event that it is not feasible to link these two packages, the modules can always be used as stand-alone tools, or linked as a single package with some restrictions in their applicability. The work done during this fiscal year has focused on developing a prototype for transporting radioactive materials

Developing Computer Model-Based Assessment of Chemical Reasoning: A Feasibility Study

Science.gov (United States)

Liu, Xiufeng; Waight, Noemi; Gregorius, Roberto; Smith, Erica; Park, Mihwa

2012-01-01

This paper reports a feasibility study on developing computer model-based assessments of chemical reasoning at the high school level. Computer models are flash and NetLogo environments to make simultaneously available three domains in chemistry: macroscopic, submicroscopic, and symbolic. Students interact with computer models to answer assessment…

Feasibility Study on Manufacturing Lightweight Aggregates from Water Purification Sludge

Science.gov (United States)

Peng, Ching-Fang; Chen, How-Ji

2018-02-01

This study mainly discussed the feasibility of manufacturing lightweight aggregates from water purification sludge in Taiwan. They were analysed for the physical and chemical composition before the sintering test for lightweight aggregates in a laboratory. Then the physical and mechanical properties of the synthesized aggregates were assessed. The result showed that the chemical composition of sludge in the water purification plants was within the appropriate range for manufacturing lightweight aggregate as proposed in the literature. The sintering test demonstrated that the particle density of aggregates from the ten types of water purification sludge were mostly less than 1.8 g/cm3. In addition, the dry unit weight, the organic impurity, the ignition loss, and other characteristics of synthesized aggregates met the requirement of CNS standards, while its water absorption and crushing strength also fulfilled the general commercial specifications. Therefore, reclamation of water purification sludge for production of lightweight aggregate is indeed feasible.

Tribal Utility Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Engel, R. A.; Zoellick, J. J.

2007-06-30

The Schatz Energy Research Center (SERC) assisted the Yurok Tribe in investigating the feasibility of creating a permanent energy services program for the Tribe. The original purpose of the DOE grant that funded this project was to determine the feasibility of creating a full-blown Yurok Tribal electric utility to buy and sell electric power and own and maintain all electric power infrastructure on the Reservation. The original project consultant found this opportunity to be infeasible for the Tribe. When SERC took over as project consultant, we took a different approach. We explored opportunities for the Tribe to develop its own renewable energy resources for use on the Reservation and/or off-Reservation sales as a means of generating revenue for the Tribe. We also looked at ways the Tribe can provide energy services to its members and how to fund such efforts. We identified opportunities for the development of renewable energy resources and energy services on the Yurok Reservation that fall into five basic categories: • Demand-side management – This refers to efforts to reduce energy use through energy efficiency and conservation measures. • Off-grid, facility and household scale renewable energy systems – These systems can provide electricity to individual homes and Tribal facilities in areas of the Reservation that do not currently have access to the electric utility grid. • Village scale, micro-grid renewable energy systems - These are larger scale systems that can provide electricity to interconnected groups of homes and Tribal facilities in areas of the Reservation that do not have access to the conventional electric grid. This will require the development of miniature electric grids to serve these interconnected facilities. • Medium to large scale renewable energy development for sale to the grid – In areas where viable renewable energy resources exist and there is access to the conventional electric utility grid, these resources can be

Economic Feasibility Study for Using Irradiation Technology in Preservation of Animalism Foods

International Nuclear Information System (INIS)

El Gameel, E.A.

2011-01-01

The present study discus the economic feasibility for the preservation animalism foods by using irradiation technology. This study has included the technical data, regression foretelling for the throughput, determination of irradiators types and radiation sources activity. This study comprises the financial analysis for the establishment animalism foods irradiation facilities (types: tote box, pallet conveyor) and the national return

Harvest for health gardening intervention feasibility study in cancer survivors.

Science.gov (United States)

Blair, Cindy K; Madan-Swain, Avi; Locher, Julie L; Desmond, Renee A; de Los Santos, Jennifer; Affuso, Olivia; Glover, Tony; Smith, Kerry; Carley, Joseph; Lipsitz, Mindy; Sharma, Ayushe; Krontiras, Helen; Cantor, Alan; Demark-Wahnefried, Wendy

2013-08-01

Cancer survivors are at increased risk for second malignancies, cardiovascular disease, diabetes, and functional decline. Evidence suggests that a healthful diet and physical activity may reduce the risk of chronic disease and improve health in this population. We conducted a feasibility study to evaluate a vegetable gardening intervention that paired 12 adult and child cancer survivors with Master Gardeners to explore effects on fruit and vegetable intake, physical activity, quality-of-life, and physical function. Throughout the year-long study period, the survivor-Master Gardener dyads worked together to plan/plant three gardens, harvest/rotate plantings, and troubleshoot/correct problems. Data on diet, physical activity, and quality-of-life were collected via surveys; anthropometrics and physical function were objectively measured. Acceptability of the intervention was assessed with a structured debriefing survey. The gardening intervention was feasible (robust enrollment; minimal attrition) and well-received by cancer survivors and Master Gardeners. Improvement in three of four objective measures of strength, agility, and endurance was observed in 90% of survivors, with the following change scores [median (interquartile range)] noted between baseline and one-year follow-up: hand grip test [+ 4.8 (3.0, 6.7) kg], 2.44 meter Get-Up-and-Go [+ 1.0 (+ 1.8, + 0.2) seconds], 30-second chair stand [+ 3.0 (+ 1.0, 5.0) stands], and six-minute walk [+ 11.6 (6.1, 48.8) meters]. Increases of ≥ 1 fruit and vegetable serving/day and ≥ 30 minutes/week of physical activity were observed in 40% and 60%, respectively. These preliminary results support the feasibility and acceptability of a mentored gardening intervention and suggest that it may offer a novel and promising strategy to improve fruit and vegetable consumption, physical activity, and physical function in cancer survivors. A larger randomized controlled trial is needed to confirm our results.

Investigation/evaluation of water cooled fast reactor in the feasibility study on commercialized fast reactor cycle systems. Intermediate evaluation of phase-II study

International Nuclear Information System (INIS)

Kotake, Syoji; Nishikawa, Akira

2005-01-01

Feasibility study on commercialized fast reactor cycle systems aims at investigation and evaluation of FBR design requirement's attainability, operation and maintenance, and technical feasibility of the candidate system. Development targets are 1) ensuring safety, 2) economic competitiveness, 3) efficient utilization of resources, 4) reduction of environmental load and 5) enhancement of nuclear non-proliferation. Based on the selection of the promising concepts in the first phase, conceptual design for the plant system has proceeded with the following plant system: a) sodium cooled reactors at large size and medium size module reactors, b) a lead-bismuth cooled medium size reactor, c) a helium gas cooled large size reactor and d) a BWR type large size FBR. Technical development and feasibility has been assessed and the study considers the need of respective key technology development for the confirmation of the feasibility study. (T. Tanaka)

Feasibility study of a level gauge using cosmic-rays

International Nuclear Information System (INIS)

Matsuda, Hideharu; Fukaya, Mitsuharu; Minato, Susumu

1989-01-01

Cosmic-ray intensities were measured at the stairs in a subway station in Nagoya City, inside a tall concrete building and under a cylindrical water tank to examine the feasibility of a cosmic-ray level gauge using a scintillation counter. The measured results agreed quite well with theoretical calculations. The maximum distinguishable water depth was evaluated to be approximately the radius of the tank from the results of many systematic calculations. It was found from these results that the practical application of a cosmic-ray level gauge is feasible. (author)

Historic Schools: Renovation vs. Replacement & the Role of a Feasibility Study.

Science.gov (United States)

National Trust for Historic Preservation, Washington, DC.

Weighing the pros and cons of renovating a historic neighborhood school or building a new one takes preservation "know-how," experience, and creativity. The potential for renovation is routinely dismissed without full consideration of the facts and long-term implications. Central to this decision-making process is the feasibility study,…

Battery energy storage market feasibility study - Expanded report

International Nuclear Information System (INIS)

Kraft, S.; Akhil, A.

1997-09-01

Under the sponsorship of the US Department of Energy's Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the battery energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed battery storage as an important technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1)

Battery energy storage market feasibility study -- Expanded report

Energy Technology Data Exchange (ETDEWEB)

Kraft, S. [Frost and Sullivan, Mountain View, CA (United States); Akhil, A. [Sandia National Labs., Albuquerque, NM (United States). Energy Storage Systems Analysis and Development Dept.

1997-09-01

Under the sponsorship of the US Department of Energy`s Office of Utility Technologies, the Energy Storage Systems Analysis and Development Department at Sandia National Laboratories (SNL) contracted Frost and Sullivan to conduct a market feasibility study of energy storage systems. The study was designed specifically to quantify the battery energy storage market for utility applications. This study was based on the SNL Opportunities Analysis performed earlier. Many of the groups surveyed, which included electricity providers, battery energy storage vendors, regulators, consultants, and technology advocates, viewed battery storage as an important technology to enable increased use of renewable energy and as a means to solve power quality and asset utilization issues. There are two versions of the document available, an expanded version (approximately 200 pages, SAND97-1275/2) and a short version (approximately 25 pages, SAND97-1275/1).

Preliminary feasibility study on production of cobalt-60 source for industrial irradiation

International Nuclear Information System (INIS)

Joo, Po Kook; Park, Kyung Bae; Ahn, Yun Soo; Lee, Jong Tai; Kim, Hark Rho

1999-05-01

As there is a high possible demand of industrial Co-60 source in the world market, feasibility study of a project was performed to produce and to export Co-60 sources, utilizing KEPCO's Wolsung NPP for irradiation of cobalt and KAERI's hot-cells for fabrication of cobalt sources. Main concerns of the study were to understand irradiation and fabrication (encapsulation) processes and to examine related technologies, required facilities and equipment. In particular, it was examined intensively if it would be possible to modify facilities around the reactor vessel of Wolsung NPP tp substantiate the related licensing in order to irradiate cobalt in the reactor. It is expected that once, if cooperation scheme with MDS Nordion of Canada is established, main issues such as modification of facilities, related licensing, raw material procurement and technology transfer for high quality product will be solved. In order to review overall feasibility of the project, present status and prospect of the world market was surveyed and various usages of cobalt sources were reviewed with emphasis on possible demand increase per usage. Food poisoning accidents are prevailing worldwide and food irradiation with cobalt sources is considered as a promising measure to prevent them and may bring forth high increase of cobalt sources demand in the world market. Preliminary economic feasibility was studied in conservation, evaluating roughly the investment and the operating cost based on materials from various information sources. (author)

Prevention of anxiety disorders in primary care: A feasibility study

Directory of Open Access Journals (Sweden)

Batelaan Neeltje M

2012-11-01

Full Text Available Abstract Background Anxiety disorders are highly prevalent in primary care and cause a substantial burden of disease. Screening on risk status, followed by preventive interventions in those at risk may prevent the onset of anxiety disorders, and thereby reduce the disease burden. The willingness to participate in screening and interventions is crucial for the scope of preventive strategies, but unknown. This feasibility study, therefore, investigated participation rates of screening and preventive services for anxiety disorders in primary care, and explored reasons to refrain from screening. Methods In three general practices, screening was offered to individuals visiting their general practitioner (total n = 2454. To assess risk status, a 10-item questionnaire was followed by a telephone interview (including the CIDI when scoring above a predefined threshold. Preventive services were offered to those at risk. Participation rates for screening and preventive services for anxiety disorders were assessed. Those not willing to be screened were asked for their main reason to refrain from screening. Results Of all individuals, 17.3% participated in initial screening, and of those with a possible risk status, 56.0% continued screening. In 30.1% of those assessed, a risk status to develop an anxiety disorder was verified. Of these, 22.6% already received some form of mental health treatment and 38.7% of them agreed to participate in a preventive intervention and were referred. The most frequently mentioned reasons to refrain from screening were the emotional burden associated with elevated risk status, the assumption not to be at risk, and a lack of motivation to act upon an elevated risk status by using preventive services. Conclusions Screening in general practice, followed by offering services to prevent anxiety disorders in those at risk did not appear to be a feasible strategy due to low participation rates. To enable the development of

Development of Bioavailability Adjustment Factors: A Feasibility Study

National Research Council Canada - National Science Library

Rembish, Steve

2000-01-01

The primary purpose of this effort is to investigate the feasibility of developing and using bioavailability adjustment factors to modify intake assumptions used in risk assessments on a site-specific basis...

Multnomah County Hydrokinetic Feasibility Study: Final Feasibility Study Report

Energy Technology Data Exchange (ETDEWEB)

Spain, Stephen

2012-03-15

HDR has completed a study of the technical, regulatory, and economic feasibility of installing hydrokinetic turbines under the Morrison, Broadway, and Sellwood bridges. The primary objective of installing hydrokinetic turbines is a demonstration of in-stream hydrokinetic technologies for public education and outreach. Due to the low gradient of the Lower Willamette and the effects of the tide, velocities in the area in consideration are simply not high enough to economically support a commercial installation. While the velocities in the river may at times provide enough energy for a commercial turbine to reach capacity, the frequency and duration of high flow events which provide suitable velocities is not sufficient to support a commercial hydrokinetic installation. We have observed that over an 11 year period, daily average velocities in the Lower Willamette exceeded a nominal cut-in speed of 0.75 m/s only 20% of the time, leaving net zero power production for the remaining 80% of days. The Sellwood Bridge site was estimated to have the best hydrokinetic resource, with an estimated average annual production of about 9,000 kWh. The estimated production could range from 2,500 kWh to 15,000 kWh. Based on these energy estimates, the amount of revenue generated through either a power purchase agreement (PPA) or recovered through net metering is not sufficient to repay the project costs within the life of the turbine. The hydrokinetic resource at the Morrison and Broadway Bridges is slightly smaller than at the Sellwood Bridge. While the Broadway and Morrison Bridges have existing infrastructure that could be utilized, the project is not expected to generate enough revenue to repay the investment. Despite low velocities and energy production, the sites themselves are favorable for installation of a demonstration or experimental project. With high public interest in renewable energy, the possibility exists to develop a hydrokinetic test site which could provide

Feasibility of a large cohort study in sub-Saharan Africa assessed through a four-country study

Directory of Open Access Journals (Sweden)

Shona Dalal

2015-05-01

Full Text Available Background: Large prospective epidemiologic studies are vital in determining disease etiology and forming national health policy. Yet, such studies do not exist in sub-Saharan Africa (SSA notwithstanding the growing burden of chronic diseases. Objective: We explored the feasibility of establishing a large-scale multicountry prospective study at five sites in four sub-Saharan countries. Design: Based on country-specific considerations of feasibility, Nigeria enrolled health care professionals, South Africa and Tanzania enrolled teachers, and Uganda enrolled village residents at one rural and one periurban site each. All sites used a 6-month follow-up period but different approaches for data collection, namely standardized questionnaires filled out by participants or face-to-face interviews. Results: We enrolled 1415 participants from five sites (range 200–489 with a median age of 41 years. Approximately half had access to clean-burning cooking fuel and 70% to piped drinking water, yet 92% had access to a mobile phone. The prevalence of chronic diseases was 49% among 45- to 54-year-olds and was dominated by hypertension (21.7% overall – ranging from 4.5 to 31.2% across sites – and a serious injury in the past 12 months (12.4% overall. About 80% of participants indicated willingness to provide blood samples. At 6-month follow-up, 68% completed a questionnaire (45 to 96% across sites with evidence that mobile phones were particularly useful. Conclusions: Our pilot study indicates that a large-scale prospective study in SSA is feasible, and the burden of chronic disease in SSA may already be substantial necessitating urgent etiologic research and primary prevention.

Draft At-Depth Study Plan for an exploratory shaft facility in salt: Revision 1

International Nuclear Information System (INIS)

1988-03-01

This draft At-Depth Study Plan describes a program of at-depth monitoring and testing in the bedded salt deposits of a candidate high-level nuclear waste repository site in Deaf Smith County, Texas. The test program will be undertaken within an At-Depth Facility (ADF) constructed at the candidate repository horizon. The purpose of the program is to assist with site characterization in support of determination of site suitability for development as a repository and for preparation of licensing documentation, and to provide information in support of repository design and performance assessment evaluation. The program includes a variety of geological, geophysical, geomechanical, thermochemical, and geohydrological monitoring and testing. The program is presented as a series of separate studies concerned with geological, geomechanical, and geohydrological site characterization, and with evaluating the mechanical and hydrological response of the site to construction of the ADF. The various studies, and associated test or monitoring methods, are included. Specific large-scale tests concerned with evaluating the performance of engineered components of the repository system (i.e., rooms, waste package, bulkhead and backfill seals) will be performed in the ADF but are described separately in individual Study Plan. 53 refs., 54 figs., 24 tabs

Can microbes compete with cows for sustainable protein production - A feasibility study on high quality protein.

Science.gov (United States)

Vestergaard, Mike; Chan, Siu Hung Joshua; Jensen, Peter Ruhdal

2016-11-08

An increasing population and their increased demand for high-protein diets will require dramatic changes in the food industry, as limited resources and environmental issues will make animal derived foods and proteins, gradually more unsustainable to produce. To explore alternatives to animal derived proteins, an economic model was built around the genome-scale metabolic network of E. coli to study the feasibility of recombinant protein production as a food source. Using a novel model, we predicted which microbial production strategies are optimal for economic return, by capturing the tradeoff between the market prices of substrates, product output and the efficiency of microbial production. A case study with the food protein, Bovine Alpha Lactalbumin was made to evaluate the upstream economic feasibilities. Simulations with different substrate profiles at maximum productivity were used to explore the feasibility of recombinant Bovine Alpha Lactalbumin production coupled with market prices of utilized materials. We found that recombinant protein production could be a feasible food source and an alternative to traditional sources.

Can microbes compete with cows for sustainable protein production - A feasibility study on high quality protein

Science.gov (United States)

Vestergaard, Mike; Chan, Siu Hung Joshua; Jensen, Peter Ruhdal

2016-11-01

An increasing population and their increased demand for high-protein diets will require dramatic changes in the food industry, as limited resources and environmental issues will make animal derived foods and proteins, gradually more unsustainable to produce. To explore alternatives to animal derived proteins, an economic model was built around the genome-scale metabolic network of E. coli to study the feasibility of recombinant protein production as a food source. Using a novel model, we predicted which microbial production strategies are optimal for economic return, by capturing the tradeoff between the market prices of substrates, product output and the efficiency of microbial production. A case study with the food protein, Bovine Alpha Lactalbumin was made to evaluate the upstream economic feasibilities. Simulations with different substrate profiles at maximum productivity were used to explore the feasibility of recombinant Bovine Alpha Lactalbumin production coupled with market prices of utilized materials. We found that recombinant protein production could be a feasible food source and an alternative to traditional sources.

Homogeneous SLOWPOKE reactor for the production of radio-isotope. A feasibility study

Energy Technology Data Exchange (ETDEWEB)

Busatta, P.; Bonin, H.W. [Royal Military College of Canada, Kingston, Ontario (Canada)]. E-mail: paul.busatta@rmc.ca; bonin-h@rmc.ca

2006-07-01

The purpose of this research is to study the feasibility of replacing the actual heterogeneous fuel core of the present SLOWPOKE-2 by a reservoir containing a homogeneous fuel for the production of Mo-99. The study looked at three items: by using the MCNP Monte Carlo reactor calculation code, develop a series of parameters required for an homogeneous fuel and evaluate the uranyl sulfate concentration of the aqueous solution fuel in order to keep a similar excess reactivity; verify if the homogeneous reactor will retain its inherent safety attributes; and with the new dimensions and geometry of the fuel core, observe whether natural convection can still effectively cool the reactor using the modeling software FEMLAB. It was found that it is indeed feasible to modify the SLOWPOKE-2 reactor for a homogeneous reactor using a solution of uranyl sulfate and water. (author)

Homogeneous SLOWPOKE reactor for the production of radio-isotope. A feasibility study

International Nuclear Information System (INIS)

Busatta, P.; Bonin, H.W.

2006-01-01

The purpose of this research is to study the feasibility of replacing the actual heterogeneous fuel core of the present SLOWPOKE-2 by a reservoir containing a homogeneous fuel for the production of Mo-99. The study looked at three items: by using the MCNP Monte Carlo reactor calculation code, develop a series of parameters required for an homogeneous fuel and evaluate the uranyl sulfate concentration of the aqueous solution fuel in order to keep a similar excess reactivity; verify if the homogeneous reactor will retain its inherent safety attributes; and with the new dimensions and geometry of the fuel core, observe whether natural convection can still effectively cool the reactor using the modeling software FEMLAB. It was found that it is indeed feasible to modify the SLOWPOKE-2 reactor for a homogeneous reactor using a solution of uranyl sulfate and water. (author)

The use of feasibility studies for stepped-wedge cluster randomised trials: protocol for a review of impact and scope.

Science.gov (United States)

Kristunas, Caroline A; Hemming, Karla; Eborall, Helen C; Gray, Laura J

2017-08-01

The stepped-wedge cluster randomised trial (SW-CRT) is a complex design, for which many decisions about key design parameters must be made during the planning. These include the number of steps and the duration of time needed to embed the intervention. Feasibility studies are likely to be useful for informing these decisions and increasing the likelihood of the main trial's success. However, the number of feasibility studies being conducted for SW-CRTs is currently unknown. This review aims to establish the number of feasibility studies being conducted for SW-CRTs and determine which feasibility issues are commonly investigated. Fully published feasibility studies for SW-CRTs will be identified, according to predefined inclusion criteria, from searches conducted in Ovid MEDLINE, Scopus, Embase and PsycINFO. To also identify and gain information on unpublished feasibility studies the following will be contacted: authors of published SW-CRTs (identified from the most recent systematic reviews); contacts for registered SW-CRTs (identified from clinical trials registries); lead statisticians of UK registered clinical trials units and researchers known to work in the area of SW-CRTs.Data extraction will be conducted independently by two reviewers. For the fully published feasibility studies, data will be extracted on the study characteristics, the rationale for the study, the process for determining progression to a main trial, how the study informed the main trial and whether the main trial went ahead. The researchers involved in the unpublished feasibility studies will be contacted to elicit the same information.A narrative synthesis will be conducted and provided alongside a descriptive analysis of the study characteristics. This review does not require ethical approval, as no individual patient data will be used. The results of this review will be published in an open-access peer-reviewed journal. © Article author(s) (or their employer(s) unless otherwise stated in

Visually guided male urinary catheterization: a feasibility study.

Science.gov (United States)

Willette, Paul A; Banks, Kevin; Shaffer, Lynn

2013-01-01

Ten percent to 15% of urinary catheterizations involve complications. New techniques to reduce risks and pain are indicated. This study examines the feasibility and safety of male urinary catheterization by nursing personnel using a visually guided device in a clinical setting. The device, a 0.6-mm fiber-optic bundle inside a 14F triple-lumen flexible urinary catheter with a lubricious coating, irrigation port, and angled tip, connects to a camera, allowing real-time viewing of progress on a color monitor. Two emergency nurses were trained to use the device. Male patients 18 years or older presenting to the emergency department with an indication for urinary catheterization using a standard Foley or Coudé catheter were eligible to participate in the study. Exclusion criteria were a current suprapubic tube or gross hematuria prior to the procedure. Twenty-five patients were enrolled. Data collected included success of placement, total procedure time, pre-procedure pain and maximum pain during the procedure, gross hematuria, abnormalities or injuries identified if catheterization failed, occurrence of and reason for equipment failures, and number of passes required for placement. All catheters were successfully placed. The median number of passes required was 1. For all but one patient, procedure time was ≤ 17 minutes. A median increase in pain scores of 1 point from baseline to the maximum was reported. Gross hematuria was observed in 2 patients. The success rate for placement of a Foley catheter with the visually guided device was 100%, indicating its safety, accuracy, and feasibility in a clinical setting. Minimal pain was associated with the procedure. Copyright © 2013 Emergency Nurses Association. Published by Mosby, Inc. All rights reserved.

Assessment of apical periodontitis by MRI. A feasibility study

Energy Technology Data Exchange (ETDEWEB)

Geibel, M.A. [Ulm Univ. (Germany). Oral and Maxillofacial Surgery; Schreiber, E.S.; Bracher, A.K.; Rasche, V. [Ulm Univ. (Germany). Internal Medicine II; Hell, E.; Ulrici, J. [Sirona Dental Systems GmbH, Bensheim (Germany). Dental Imaging; Sailer, L.K. [DOC Praxisklinik im Wiley, Neu-Ulm (Germany). MKG; Ozpeynirci, Y. [Ulm Univ. (Germany). Diagnostic and Interventional Radiology

2015-04-15

The purpose of this clinical feasibility study was to evaluate the applicability of magnetic resonance imaging (MRI) for the assessment of apical periodontitis in direct comparison with cone beam CT (CBCT). 19 consecutive patients (average age 43 ± 13 years) with 34 lesions in total (13 molars, 14 premolars and 7 front teeth) were enrolled in this feasibility study. Periapical lesions were defined as periapical radiolucencies (CBCT) or structural changes in the spongy bone signal (MRI), which were connected with the apical part of a root and with at least twice the width of the periodontal ligament space. The location and dimension of the lesions were compared between MRI and CBCT. While mainly mineralized tissue components such as teeth and bone were visible with CBCT, complimentary information of the soft tissue components was assessable with MRI. The MRI images provided sufficient diagnostic detail for the assessment of the main structures of interest. Heterogeneous contrast was observed within the lesion, with often a clear enhancement close to the apical foramen and the periodontal gap. No difference for lesion visibility was observed between MRI and CBCT. The lesion dimensions corresponded well, but were slightly but significantly overestimated with MRI. A heterogeneous lesion appearance was observed in several patients. Four patients presented with a well circumscribed hyperintense signal in the vicinity of the apical foramen. The MRI capability of soft tissue characterization may facilitate detailed analysis of periapical lesions. This clinical study confirms the applicability of multi-contrast MRI for the identification of periapical lesions.

Assessment of apical periodontitis by MRI. A feasibility study

International Nuclear Information System (INIS)

Geibel, M.A.; Schreiber, E.S.; Bracher, A.K.; Rasche, V.; Hell, E.; Ulrici, J.; Sailer, L.K.; Ozpeynirci, Y.

2015-01-01

The purpose of this clinical feasibility study was to evaluate the applicability of magnetic resonance imaging (MRI) for the assessment of apical periodontitis in direct comparison with cone beam CT (CBCT). 19 consecutive patients (average age 43 ± 13 years) with 34 lesions in total (13 molars, 14 premolars and 7 front teeth) were enrolled in this feasibility study. Periapical lesions were defined as periapical radiolucencies (CBCT) or structural changes in the spongy bone signal (MRI), which were connected with the apical part of a root and with at least twice the width of the periodontal ligament space. The location and dimension of the lesions were compared between MRI and CBCT. While mainly mineralized tissue components such as teeth and bone were visible with CBCT, complimentary information of the soft tissue components was assessable with MRI. The MRI images provided sufficient diagnostic detail for the assessment of the main structures of interest. Heterogeneous contrast was observed within the lesion, with often a clear enhancement close to the apical foramen and the periodontal gap. No difference for lesion visibility was observed between MRI and CBCT. The lesion dimensions corresponded well, but were slightly but significantly overestimated with MRI. A heterogeneous lesion appearance was observed in several patients. Four patients presented with a well circumscribed hyperintense signal in the vicinity of the apical foramen. The MRI capability of soft tissue characterization may facilitate detailed analysis of periapical lesions. This clinical study confirms the applicability of multi-contrast MRI for the identification of periapical lesions.

Raising the profile of pilot and feasibility studies in relation to the development, evaluation and implementation of patient-reported outcome measures.

OpenAIRE

Jones, GL

2017-01-01

This editorial introduces a new special series on the pilot and feasibility testing of patient-reported outcome measures (PROMs) in the on-line open access journal Pilot and Feasibility Studies. Pilot and feasibility studies are typically implemented to address issues of uncertainty before undertaking a larger definitive study such as a randomised controlled trial or large scale survey. This editorial considers the role that such pilot and feasibility testing plays in relation to the developm...

Rebuilding self-confidence after cancer: a feasibility study of life-coaching.

Science.gov (United States)

Wagland, Richard; Fenlon, Deborah; Tarrant, Ruth; Howard-Jones, Gilly; Richardson, Alison

2015-03-01

Cancer survivors often experience decreased self-confidence which impacts negatively on their ability to self-manage the practical, social and emotional problems frequently faced as they emerge from end of treatment. This was a feasibility study of a life-coaching intervention, designed to rebuild confidence of survivors and support transition to life after cancer treatment. A one group pre-test, post-test design was used, recruiting participants from community organisations. Eligibility criteria are as follows: 18, no metastases, and no mental health problems. Participants received one individualised face-to-face and five telephone coaching sessions over 3 months. Outcome measures are as follows: New General Self-Efficacy Scale, Hope Scale, Personal Well-being Index, Assessment of Survivorship Concerns, Quality of Life in Adult Cancer Survivors, Hospital Anxiety and Depression Scale, Social Difficulties Index, and a goal attainment score. Interviews explored feasibility, acceptability and impact of life-coaching and research design. Nine women and two men were recruited, representing varying cancer diagnoses. All outcome measures were sensitive to change and indicated positive trends post-intervention. Participant interviews indicated the intervention was well received and had a positive impact. Lessons were learnt about study design, recruitment and intervention delivery. Life-coaching has a potential to enable cancer survivors to manage the transition to life beyond cancer and effect change on a range of outcomes. The intervention was feasible to deliver and acceptable to survivors at a time when many struggle to make sense of life. It merits further evaluation through a randomised controlled trial.

Istra district heating system. Master plan and feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-01

This report presents the results of the Feasibility Study of options for improving the efficiency and operating economy of Istra Large-Scale Demonstration Project includes all areas of the town of Istra. However, the Feasibility Study is confined to the five largest adjoining boilers plant areas within the borders of Istra town. The study was conducted from 1999 to 2001 and was based on information collected during this period. The city administration and the district heating company in Istra provided the data. The company RDIEE, Russian Danish Institute for Energy Efficiency, in Istra collected and processed the data under the conduction of Carl Bro a/s in Denmark. The main objectives of the study are to provide the Istra DHC with a number of options for future development of the district heating system based on technical/financial analyses and presenting the best possibilities for improved comfort, operation and business development. More concretely, one or more system improvement scenarios, which can be implemented in the near future as a first step of the recommended medium-term to long-term development, are identified. Another important objective has been to train the specialists of RDIEE in the feasibility study process and to transfer know-how, skills and tools. The model used for this study is adapted to the features and the special problems to be addressed in relation to the Istra district heating system. RDIEE and Istra DHC are thereby provided with a useful tool which may be used for continued study and development after the first phase project has been completed. As usual in the case of input/output models the quality of the results depends very much on the quality of input data. The present report is exclusively based on the consultant's understanding of the provided information. The results and the underlying inputs should be carefully considered before any final decision concerning implementation is taken. Verification of assumptions should also

Internet-based cognitive behavioral therapy for adolescents with anxiety disorders: A feasibility study

Directory of Open Access Journals (Sweden)

Silke Stjerneklar

2018-03-01

Conclusion: Results from this study indicate that a translated and revised version of the Chilled Out program could be a feasible psychological intervention for Danish adolescents with anxiety disorders.

Determination of geohydrologic framework and extent of d- water contamination using surface geophysical techniques at Picatinny Arsenal, New Jersey

Science.gov (United States)

Lacombe, Pierre

1986-01-01

Seismic-refraction, electric-resistivity sounding, and electromagnetic conductivity techniques were used to determine the geohydrologic framework and extent of groundwater contamination at Picatinny Arsenal in northern New Jersey. The area studied encompasses about 4 sq mi at the southern end of the Arsenal. The bedrock surface beneath the glacial sediments was delineated by seismic-refraction techniques. Data for 12 seismic lines were collected using a 12-channel engineering seismograph. Competent bedrock crops out on both sides of the valley, but is about 290 ft below land surface in the deepest part of the topographic valley. Where the exposed bedrock surface forms steep slopes on the valley side, it remains steep below the valley fill. Likewise, gentle bedrock valley slopes have gentle subsurface slopes. The deepest part of the bedrock valley is along the southern extension of the Green Pond fault. The electric-resistivity sounding technique was used to determine the sediment types. Data were collected from four sites using the offset Wenner electrode configuration. Below the surface layer, the sediments have apparent and computed resistivity values of 120 to 170 ohm-meters. These values correspond to a saturated fine-grained sediment such as silt or interbedded sand and clay. Groundwater contamination was by electromagnetic conductivity techniques using transmitting and receiving coils separated by 32.8 ft and 12 ft. Thirteen sites have apparent conductivity values exceeding 15 millimhos/m. Of these, seven sites indicate groundwater contamination from a variety of sources including a sanitary landfill, pyrotechnic testing ground, burning area, former domestic sewage field, salt storage facility, hazardous waste disposal lagoon, sewage treatment plant, and fertilizer storage shed. Three areas underlain by clay or muck are interpreted to be free of contamination. (Author 's abstract)

Dementia care mapping to support staff in the care of people with intellectual disability and dementia: a feasibility study.

Science.gov (United States)

Schaap, Feija D; Fokkens, Andrea S; Dijkstra, Geke J; Reijneveld, Sijmen A; Finnema, Evelyn J

2018-04-24

The number of people with intellectual disability and dementia increases; this combination causes behavioural changes. Dementia Care Mapping (DCM) supports staff in dementia care in nursing homes and may be useful in intellectual disability-care. This qualitative study examines the feasibility of DCM for older people with intellectual disability and dementia. The present authors obtained data in focus groups and interviews with professional users and analysed using a framework for feasibility studies. With experts in dementia and intellectual disability researches, the present authors determined the overall feasibility. DCM was found to be feasible in intellectual disability-care, regarding five domains of feasibility. Staff reported DCM to be useful and valuable and addresses to their demand for skills and knowledge. All professional users found DCM feasible in intellectual disability-care, which was confirmed by experts. DCM is feasible in intellectual disability-care. When fully tailored to intellectual disability-care, DCM is useful and provides opportunities to assess its effectiveness. © 2018 The Authors. Journal of Applied Research in Intellectual Disabilities Published by John Wiley & Sons Ltd.

Feasibility study for mega-electron-volt electron beam tomography.

Science.gov (United States)

Hampel, U; Bärtling, Y; Hoppe, D; Kuksanov, N; Fadeev, S; Salimov, R

2012-09-01

Electron beam tomography is a promising imaging modality for the study of fast technical processes. But for many technical objects of interest x rays of several hundreds of keV energy are required to achieve sufficient material penetration. In this article we report on a feasibility study for fast electron beam computed tomography with a 1 MeV electron beam. The experimental setup comprises an electrostatic accelerator with beam optics, transmission target, and a single x-ray detector. We employed an inverse fan-beam tomography approach with radiographic projections being generated from the linearly moving x-ray source. Angular projections were obtained by rotating the object.

Feasibility Study of Non-Destructive Techniques to Measure Corrosion in SAVY Containers

Energy Technology Data Exchange (ETDEWEB)

Davenport, Matthew Nicholas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-07-15

Stainless Steel SAVY containers are used to transport and store nuclear material. They are prone to interior corrosion in the presence of certain chemicals and a low-oxygen environment. SAVY containers also have relatively thin walls to reduce their weight, making their structural integrity more vulnerable to the effects of corrosion. A nondestructive evaluation system that finds and monitors corrosion within containers in use would improve safety conditions and preclude hazards. Non-destructive testing can determine whether oxidation or corrosion is occurring inside the SAVY containers, and there are a variety of non-destructive testing methods that may be viable. The feasibility study described will objectively decide which method best fits the requirements of the facility and the problem. To improve efficiency, the containers cannot be opened during the non-destructive examination. The chosen technique should also be user-friendly and relatively quick to apply. It must also meet facility requirements regarding wireless technology and maintenance. A feasibility study is an objective search for a new technology or product to solve a particular problem. First, the design, technical, and facility feasibility requirements are chosen and ranked in order of importance. Then each technology considered is given a score based upon a standard ranking system. The technology with the highest total score is deemed the best fit for a certain application.

Developing an undergraduate degree in public transportation administration and management : feasibility study results.

Science.gov (United States)

2006-11-01

Experiences and results of research by the North Carolina Central University Department of Public Administration while a : conducting feasibility study for establishing a new multidisciplinary undergraduate degree in public transportation administrat...

Canton hydroelectric project: feasibility study. Final report, appendices

Energy Technology Data Exchange (ETDEWEB)

1979-05-01

These appendices contain legal, environmental, regulatory, technical and economic information used in evaluating the feasibility of redeveloping the hydroelectric power generating facilities at the Upper and Lower Dams of the Farmington River at Collinsville, CT. (LCL)

Homogeneous Slowpoke reactor for the production of radio-isotope: a feasibility study

Energy Technology Data Exchange (ETDEWEB)

Busetta, P.; Bonin, H.W. [Royal Military College of Canada, Kingston, Ontario (Canada)

2006-09-15

The purpose of this research is to study the feasibility of replacing the actual heterogeneous fuel core of the present SLOWPOKE-2 by a reservoir containing a homogeneous fuel for the production of Mo-99. The study looked at three items: by using the MCNP Monte Carlo reactor calculation code, develop a series of parameters required for an homogeneous fuel and evaluate the uranyl sulfate concentration of the aqueous solution fuel in order to keep a similar excess reactivity; verify if the homogeneous react will retain its inherent safety attributes; and with the new dimensions and geometry of the fuel core, observe whether natural convection can still effectively cool the reactor using the modeling software FEMLAB(r). It was found that it is needed feasible to modify the SLOWPOKE-2 reactor for a homogeneous reactor using a solution of uranyl sulfate and water. (author)

Feasibility Study of a Performance-Based Teacher Education Curriculum in Language Arts.

Science.gov (United States)

Rudman, Masha Kabakow

This report of a feasibility study, conducted under the provisions of a model elementary teacher education grant from the U.S. Office of Education, is in five parts. Chapter one contains an overview of and rationale for a performance-based teacher education program, a brief history of the study, the attitude and ability goals expected from…

Economical and technical feasibility study of some radioisotopes production for medical application

International Nuclear Information System (INIS)

Souza, A.L.A.B. de.

1985-01-01

The economical and technical feasibility study of the production in reactors of some radioisotopes most used in medicine, are presented. The clinical applications of each radioisotope as well as its radioactive concentrations and specific activities are related. Irradiation procedures based in the foregoing data are given. Part of the study is dedicated to quality control. (M.A.C.) [pt

Feasibility study of Transcutaneous Electrical Nerve Stimulation (TENS) for cancer bone pain.

Science.gov (United States)

Bennett, Michael I; Johnson, Mark I; Brown, Sarah R; Radford, Helen; Brown, Julia M; Searle, Robert D

2010-04-01

This multicenter study assessed the feasibility of conducting a phase III trial of transcutaneous electrical nerve stimulation (TENS) in patients with cancer bone pain recruited from palliative care services. Eligible patients received active and placebo TENS for 1 hour at site of pain in a randomized crossover design; median interval between applications 3 days. Responses assessed at 30 and 60 minutes included numerical and verbal ratings of pain at rest and on movement, and pain relief. Recruitment, tolerability, adverse events, and effectiveness of blinding were also evaluated. Twenty-four patients were randomised and 19 completed both applications. The intervention was well tolerated. Five patients withdrew: 3 due to deteriorating performance status, and 2 due to increased pain (1 each following active and placebo TENS). Confidence interval estimation around the differences in outcomes between active and placebo TENS suggests that TENS has the potential to decrease pain on movement more than pain on rest. Nine patients did not consider that a placebo was used; the remaining 10 correctly identified placebo TENS. Feasibility studies are important in palliative care prior to undertaking clinical trials. Our findings suggest that further work is required on recruitment strategies and refining the control arm before evaluating TENS in cancer bone pain. Cancer bone pain is common and severe, and partly mediated by hyperexcitability. Animal studies suggest that Transcutaneous Electrical Nerve Stimulation can reduce hyperalgesia. This study examined the feasibility of evaluating TENS in patients with cancer bone pain in order to optimize methods before a phase III trial. Copyright 2010 American Pain Society. Published by Elsevier Inc. All rights reserved.

Is an opportunistic primary care-based intervention for non-responders to bowel screening feasible and acceptable? A mixed-methods feasibility study in Scotland.

Science.gov (United States)

Calanzani, Natalia; Cavers, Debbie; Vojt, Gabriele; Orbell, Sheina; Steele, Robert J C; Brownlee, Linda; Smith, Steve; Patnick, Julietta; Weller, David; Campbell, Christine

2017-10-11

We aimed to test whether a brief, opportunistic intervention in general practice was a feasible and acceptable way to engage with bowel screening non-responders. This was a feasibility study testing an intervention which comprised a brief conversation during routine consultation, provision of a patient leaflet and instructions to request a replacement faecal occult blood test kit. A mixed-methods approach to evaluation was adopted. Data were collected from proformas completed after each intervention, from the Bowel Screening Centre database and from questionnaires. Semi-structured interviews were carried out. We used descriptive statistics, content and framework analysis to determine intervention feasibility and acceptability. Bowel screening non-responders (as defined by the Scottish Bowel Screening Centre) and primary care professionals working in five general practices in Lothian, Scotland. Several predefined feasibility parameters were assessed, including numbers of patients engaging in conversation, requesting a replacement kit and returning it, and willingness of primary care professionals to deliver the intervention. The intervention was offered to 258 patients in five general practices: 220 (87.0%) engaged with the intervention, 60 (23.3%) requested a new kit, 22 (8.5%) kits were completed and returned. Interviews and questionnaires suggest that the intervention was feasible, acceptable and consistent with an existing health prevention agenda. Reported challenges referred to work-related pressures, time constraints and practice priorities. This intervention was acceptable and resulted in a modest increase in non-responders participating in bowel screening, although outlined challenges may affect sustained implementation. The strategy is also aligned with the increasing role of primary care in promoting bowel screening. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use

Feasibility Study of Biomass Electrical Generation on Tribal Lands

Energy Technology Data Exchange (ETDEWEB)

Tom Roche; Richard Hartmann; Joohn Luton; Warren Hudelson; Roger Blomguist; Jan Hacker; Colene Frye

2005-03-29

The goals of the St. Croix Tribe are to develop economically viable energy production facilities using readily available renewable biomass fuel sources at an acceptable cost per kilowatt hour ($/kWh), to provide new and meaningful permanent employment, retain and expand existing employment (logging) and provide revenues for both producers and sellers of the finished product. This is a feasibility study including an assessment of available biomass fuel, technology assessment, site selection, economics viability given the foreseeable fuel and generation costs, as well as an assessment of the potential markets for renewable energy.

Feasibility Study of a Lunar Analog Bed Rest Model

Science.gov (United States)

Cromwell, Ronita L.; Platts, Steven H.; Yarbough, Patrice; Buccello-Stout, Regina

2010-01-01

The purpose of this study was to determine the feasibility of using a 9.5deg head-up tilt bed rest model to simulate the effects of the 1/6 g load to the human body that exists on the lunar surface. The lunar analog bed rest model utilized a modified hospital bed. The modifications included mounting the mattress on a sled that rolled on bearings to provide freedom of movement. The weight of the sled was off-loaded using a counterweight system to insure that 1/6 body weight was applied along the long axis (z-axis) of the body. Force was verified through use of a force plate mounted at the foot of the bed. A seating assembly was added to the bed to permit periods of sitting. Subjects alternated between standing and sitting positions throughout the day. A total of 35% of the day was spent in the standing position and 65% was spent sitting. In an effort to achieve physiologic fluid shifts expected for a 1/6 G environment, subjects wore compression stockings and performed unloaded foot and ankle exercises. Eight subjects (3 females and 5 males) participated in this study. Subjects spent 13 days in the pre-bed rest phase, 6 days in bed rest and 3 days post bed rest. Subjects consumed a standardized diet throughout the study. To determine feasibility, measures of subject comfort, force and plasma volume were collected. Subject comfort was assessed using a Likert scale. Subjects were asked to assess level of comfort (0-100) for 11 body regions and provide an overall rating. Results indicated minimal to no discomfort as most subjects reported scores of zero. Force measures were performed for each standing position and were validated against subject s calculated 1/6 body weight (r(sup 2) = 0.993). The carbon monoxide rebreathing technique was used to assess plasma volume during pre-bed rest and on the last day of bed rest. Plasma volume results indicated a significant decrease (p = 0.001) from pre to post bed rest values. Subjects lost on average 8.3% (sd = 6.1%) during the

Progress Report: Feasibility Study of an Indium Scintillator Solar Neutrino Experiment

International Nuclear Information System (INIS)

Bellefon, A. de; Barloutaud, R.; Borg, A.; Ernwein, J.; Mosca, L.

1989-09-01

In this document, we report on the progress made to demonstrate the feasibility of an experiment which would measure for the first time the two line sources of solar neutrinos resulting from electron capture by 7 Be and from the p-e-p reaction inside the sun. The detector under study consists of scintillator containing 10 tons of Indium

Nuclear power planning and feasibility studies

International Nuclear Information System (INIS)

Streeton, D.F.

1977-01-01

This lecture will review the basic steps associated with planning the introduction of nuclear power. Areas covered will include power market surveys, energy resources evaluations, potential alternative strategies, organisational factors and implementational requirements. The lecture will then consider the implications and requirements associated with establishing the feasibility of a nuclear project. Among others, aspects of power systems integration, site selection reactor type evaluation, cost and economic analysis, influence of contracting strategies, comparison with alternative power generation solutions, financial impact, etc. will be discussed and reviewed. (HK) [de

Aerospace Engineering Space Mission Concept Feasibility Study: A Neptune Mission Design Example

Science.gov (United States)

Esper, Jaime

2007-01-01

This viewgraph document reviews the feasibility study of a mission to Neptune. Included are discussions of the science instruments, the design methodology, the trajectory, the spacecraft design, the alternative propulsion systems, (chemical, solar electric (SEP)), the communications systems, the power systems, the thermal system.

Hot stamping of an Al-Li alloy: a feasibility study

Directory of Open Access Journals (Sweden)

Gao Haoxiang

2016-01-01

Full Text Available The feasibility of forming a third generation aluminium-lithium alloy (AA2060 into a complex shaped panel component, was studied by using an advanced forming technology called solution heat treatment, cold die forming and in-die quenching (HFQa process. The main challenges using HFQ technology to form complex shaped AA2060 component was to find out optimum forming parameters, such as forming temperature, forming speed, lubrication condition and blank holding force. In this paper, the optimum forming temperature was mainly concerned. The flow stresses of AA2060 were obtained at different temperatures ranging from 350 to 520 °C at the strain rate of 2 s−1. The suitable temperature to achieve the adequate ductility was found at 470 °C. By forming the AA2060 blanks at the optimum forming temperature, experimental results exhibited the feasibility for forming complex-shaped AA2060 components. The formed components were analysed through strain measurements. The post-form mechanical properties of AA2060 were assessed using hardness and tensile tests.

Feasibility study of a vertical slit for the LBS line of the Linac4

CERN Document Server

Ouzia, Alexandre; Maglioni, Cesare; Leitao, Ivo

The feasibility study of a vertical Slit was performed. This Slit is needed for the diagnostic Line for Beam energy Spread of the Linac 4 (LBS line). The Linac 4 will replace the Linac 2 and enable the Large Hadron Collider (LHC) to reach an energy of 14 TeV (highest energy ever reached). When the beam impact on it, the Slit heats up and deforms. The deformation of the slit is the key problem. The present feasibility study aims at assessing whether or not it is feasible to keep this deformation below 50_m, according to the specifications [14]. The determination of all the issues related with the Slit was driven. The priority was given to the thermo-mechanical issues. The methodology chosen to approach the problem led to three steps: -\tFirst, the determination of possible designs for the Slit. One design was identified. -\tSecond, the determination of the best materials. Two figures of merit and a model were specifically conceived for it. Graphite R4550 was identified as the best material. -\tThird, the Monte-Ca...

A feasibility study for a manufacturing technology deployment center

Energy Technology Data Exchange (ETDEWEB)

1994-10-31

The Automation & Robotics Research Institute (ARRI) and the Texas Engineering Extension Service (TEEX) were funded by the U.S. Department of Energy to determine the feasibility of a regional industrial technology institute to be located at the Superconducting Super Collider (SSC) Central Facility in Waxahachie, Texas. In response to this opportunity, ARRI and TEEX teamed with the DOE Kansas City Plant (managed by Allied Signal, Inc.), Los Alamos National Laboratory (managed by the University of California), Vought Aircraft Company, National Center for Manufacturing Sciences (NCMS), SSC Laboratory, KPMG Peat Marwick, Dallas County Community College, Navarro Community College, Texas Department of Commerce (TDOC), Texas Manufacturing Assistance Center (TMAC), Oklahoma Center for the Advancement of Science and Technology, Arkansas Science and Technology Authority, Louisiana Productivity Center, and the NASA Mid-Continent Technology Transfer Center (MCTTC) to develop a series of options, perform the feasibility analysis and secure industrial reviews of the selected concepts. The final report for this study is presented in three sections: Executive Summary, Business Plan, and Technical Plan. The results from the analysis of the proposed concept support the recommendation of creating a regional technology alliance formed by the states of Texas, New Mexico, Oklahoma, Arkansas and Louisiana through the conversion of the SSC Central facility into a Manufacturing Technology Deployment Center (MTDC).

Feasibility study for an alternative PWR-containment. Stage 3

International Nuclear Information System (INIS)

Eibl, J.

1994-08-01

The following report deals with a feasibility study on a lightwater reactor containment which is oriented at the German 1300 MW Convoy Type reactor. It was the aim of this containment development for a future nuclear ractor to restrict all consequences of an extreme reactor failure exclusively to the interior of the containment. Also the decay heat of the relevant core catchers is provided to be removed by passive means. This containment development was a common project with the Nuclear Research Centre at Karlsruhe (KFK). As a consequence of this intention the concept started from upper physical limits, such as a maximum static pressure of 1,5 MPa at 200 , a global and local detonation pressure of 8,4 MPa at an impulse of 5,0 kPas, an upward directed force exerted by the pressure vessel of 300 MN, a horizontal force exerted by the moving pressure vessel onto its environment of 70 MN, a cavern pressure around the core catcher of 3,0 resp., 2,0 MPa and a steam explosion-energy of 300 MJ. Such a contaiment concept is presented and inverstigated with respect to its feasibility, statically and dynamically in all relevant details including earthquake actions. (orig.) [de

FEASIBILITY STUDY OF SEDIMENT FLUSHING FROM MOSUL RESERVOIR, IRAQ

Directory of Open Access Journals (Sweden)

Thair Mahmood Al-Taiee

2015-02-01

Full Text Available The Feasibility of sediment flushing  from Mosul reservoir located northern iraq was conducted. Many up to date world criteria and indices for checking the efficiency of sediment flushing from reservoir which have been got through analyzing large amount of  data from many flushed reservoirs  in the world which were depended tested and applied in the present case study (Mosul Reservoir. These criteria and indices depend mainly on the hydrological , hydraulic and  topographical properties of the reservoirs in-addition to the operation plan of the reservoirs. They gave a good indication for checking the efficiency of the sediment flushing  process in the reservoirs. It was concluded that approximately the main criteria for the successful flushing sediment was  verified  in  Mosul  reservoir  such as  Sediment Balance Ratio   (SBR and the Long Term Capacity Ratio (LTCR,the shape factor  of reservoir (W/L and the hydraulic condition such as the percentage of (Qf/Qin and (Vf/Vin. This gave an indication that the processes of flushing sediment in Mosul reservoir is probably feasible and may be applied  in the future to maintain the water storage in the reservoir.

A feasibility study of using remotely sensed data for water resource models

Science.gov (United States)

Ruff, J. F.

1973-01-01

Remotely sensed data were collected to demonstrate the feasibility of applying the results to water resource problems. Photographs of the Wolf Creek watershed in southwestern Colorado were collected over a one year period. Cloud top temperatures were measured using a radiometer. Thermal imagery of the Wolf Creek Pass area was obtained during one pre-dawn flight. Remote sensing studies of water resource problems for user agencies were also conducted. The results indicated that: (1) remote sensing techniques could be used to assist in the solution of water resource problems; (2) photogrammetric determination of snow depths is feasible; (3) changes in turbidity or suspended material concentration can be observed; and (4) surface turbulence can be related to bed scour; and (5) thermal effluents into rivers can be monitored.

The offshore disposal of radioactive waste by drilled emplacement: A feasibility study

International Nuclear Information System (INIS)

Bury, M.R.C.

1985-01-01

This book is a report, based on a study by Taylor Woodrow Construction Limited, on the overall feasibility of the disposal of high-level radioactive waste in boreholes drilled deep into the ocean bed. The work comprises an engineering appraisal of the disposal process with a view to establishing technical and operational feasibility and providing overall cost information to enable an economic assessment to be made. Contents: Summary report; Reference criteria; Drilling operation; Transfer of radioactive waste, personnel and other supplies; Handling of radioactive waste on board; Lowering strings of canisters; Emplacement and backfilling of canisters; Preliminary design of marine platform; Retrieval of flasks or canisters lost or misplaced; Variations to the features of the lowering system; Logistics of the operation; Construction cost estimate; Operational costs; Appendix

14-plex Feasibility Report

Energy Technology Data Exchange (ETDEWEB)

Kotongan, Victoria Hazel [Native Village of Unalakleet

2013-06-21

The Native Village of Unalakleet project was a feasibility study for a retrofit of a “tribally owned” three story, 14 apartment complex located in Unalakleet, Alaska. The program objective and overall goal was to create a plan for retrofitting to include current appraised value and comparable costs of new construction to determine genuine feasibility as low-income multi-family housing for tribal members.

A Summary of Two Recent UAS Command and Control (C2) Communications Feasibility Studies

Science.gov (United States)

Ponchak, Denise S.; Auld, Elisabeth; Church, Gary; Henriksen, Stephen

2016-01-01

In Spring of 2015, the NextGen Institute conducted two UAS C2 Communications Feasibility Studies on behalf of the FAA UAS Integration Office to develop two limited UAS C2 operational examples, each involving low-altitude BLOS (Beyond Line of Sight) Line of Communication (LOC) UAS applications, as part of assessing the myriad practical UAS C2 deployment challenges associated with these approaches. The studies investigated the feasibility of "Point-to-Point" (PTP) and "Network" approaches to UAS C2 to better understand potential user needs and to explore evolutionary paths to establishing a nation-wide system for delivering UAS C2 communications. This paper will summarize the solicitation, approach and results of the two studies teams led by Aviation Management Associates, Inc. and Exelis Inc.

Feasibility study of hybrid retrofits to an isolated off-grid diesel power plant

International Nuclear Information System (INIS)

Rehman, S.; Ahmad, F.; Shaahid, S.M.; Shash, A.; El-Amin, I.M.; Al-Shehri, A.M.; Bakhashwain, J.M.

2007-01-01

The green sources of energy are being encouraged to reduce the environmental pollution and combat the global warming of the planet. A target of 12% usage of wind energy only has been agreed by the UNO country members to achieve by 2020. So, the power of the wind is being used to generate electricity both as grid connected and isolated wind-diesel hybrid power plants. This paper performed a pre-feasibility of wind penetration into an existing diesel plant of a village in north eastern part of Saudi Arabia. For simulation purpose, wind speed data from a near by airport and the load data from the village have been used. The hybrid system design tool HOMER has been used to perform the feasibility study. In the present scenario, for wind speed less than 6.0m/s the, the existing diesel power plant is the only feasible solution over the range of fuel prices used in the simulation. The wind diesel hybrid system becomes feasible at a wind speed of 6.0m/s or more and a fuel price of 0.1$/L or more. If the carbon tax is taken into consideration and subsidy is abolished then it is expected that the hybrid system become feasible. The maximum annual capacity shortage did not have any effect on the cost of energy which may be accounted for larger sizes of wind machines and diesel generators. It is recommended that the wind data must be collected at the village at three different heights using a wind mast of 40m for a minimum of one complete year and then the hybrid system must be re-designed. (author)

Autonomous Aerobraking: A Design, Development, and Feasibility Study

Science.gov (United States)

Prince, Jill L. H.; Powell, Richard W.; Murri, Dan

2011-01-01

Aerobraking has been used four times to decrease the apoapsis of a spacecraft in a captured orbit around a planetary body with a significant atmosphere utilizing atmospheric drag to decelerate the spacecraft. While aerobraking requires minimum fuel, the long time required for aerobraking requires both a large operations staff, and large Deep Space Network resources. A study to automate aerobraking has been sponsored by the NASA Engineering and Safety Center to determine initial feasibility of equipping a spacecraft with the onboard capability for autonomous aerobraking, thus saving millions of dollars incurred by a large aerobraking operations workforce and continuous DSN coverage. This paper describes the need for autonomous aerobraking, the development of the Autonomous Aerobraking Development Software that includes an ephemeris estimator, an atmospheric density estimator, and maneuver calculation, and the plan forward for continuation of this study.

Feasibility study on utilization of vitrified radioactive waste as radiation sources

International Nuclear Information System (INIS)

Makuuchi, Keizo; Yoshii, Fumio; Hyakutake, Kenichiro

1995-01-01

A feasibility study on utilization of vitrified high level radioactive waste (VW) as radiation source has been carried out. Natural rubber latex was radiation vulcanized with VW to demonstrate the feasibility. The dose rate was 0.1 kGy/hr. As a sensitizer, n-butyl acrylate was added. Negligible small activation of natural rubber (NR) latex by neutron from the VW was observed. The residual sensitizer in the irradiated latex and physical properties of film molded from the irradiated latex were the same level with the conventional radiation vulcanization of NR latex with γ-rays from Co-60. Surgical gloves and protective rubber gloves for radioactive contamination were produced from 20 litters of NR latex vulcanized with 2 VWs. The physical properties of both gloves were acceptable. These results suggested that vitrified high level waste can be used as an industrial radiation source. (author)

Feasibility study for remote assessment of cognitive function in multiple sclerosis.

Science.gov (United States)

George, Michaela F; Holingue, Calliope B; Briggs, Farren B S; Shao, Xiaorong; Bellesis, Kalliope H; Whitmer, Rachel A; Schaefer, Catherine; Benedict, Ralph Hb; Barcellos, Lisa F

2016-01-01

Cognitive impairment is common in multiple sclerosis (MS), and affects employment and quality of life. Large studies are needed to identify risk factors for cognitive decline. Currently, a MS-validated remote assessment for cognitive function does not exist. Studies to determine feasibility of large remote cognitive function investigations in MS have not been published. To determine whether MS patients would participate in remote cognitive studies. We utilized the Modified Telephone Interview for Cognitive Status (TICS-M), a previously validated phone assessment for cognitive function in healthy elderly populations to detect mild cognitive impairment. We identified factors that influenced participation rates. We investigated the relationship between MS risk factors and TICS-M score in cases, and score differences between cases and control individuals. The TICS-M was administered to MS cases and controls. Linear and logistic regression models were utilized. 11.5% of eligible study participants did not participate in cognitive testing. MS cases, females and individuals with lower educational status were more likely to refuse (pTICS-M score among cases (pTICS-M score was significantly lower in cases compared to controls (p=0.007). Our results demonstrate convincingly that a remotely administered cognitive assessment is quite feasible for conducting large epidemiologic studies in MS, and lay the much needed foundation for future work that will utilize MS-validated cognitive measures.

Feasibility study of a biomass-fired cogeneration plant Groningen, Netherlands

International Nuclear Information System (INIS)

Rijk, P.J.; Van Loo, S.; Webb, R.

1996-06-01

The feasibility of the title plant is determined for district heating and electricity supply of more than 1,000 houses in Groningen, Netherlands. Also attention is paid to the feasibility of such installations in a planned area of the city. Prices and supply of several biomass resources are dealt with: prunings of parks, public and private gardens, clean wood wastes, wood wastes from forests, wood from newly planted forests, specific energy crops (willows in high densities and short cycles). Prices are calculated, including transport to the gate of the premises where the cogeneration installations is situated. For the conversion attention is paid to both the feasibility of the use of a conventional cogeneration installation (by means of a steam turbine) and the use of a new conversion technique: combined cycle of a gasification installation and a cogeneration installation. 5 figs., 5 ills., 22 tabs., 1 appendix, 33 refs

The Results of Feasibility Study of Co-generation NPP With Innovative VK-300 Simplified Boiling Water Reactor

International Nuclear Information System (INIS)

Kuznetsov, Yury N.

2006-01-01

The co-generation nuclear power plant (CNPP) producing electricity and district heating heat is planned to be constructed in Archangelsk Region of Russia. Following the 'Letter of Intent' signed by Governor of Archangelsk region and by Minister of the Russian Federation for atomic energy the feasibility study of the Project has been done. The NPP will be based on the four co-generation nuclear power units with the Russian VK-300 SBWR. The innovative passive VK-300 reactor facility has been designed on the basis of well-established nuclear technologies, proven major components, the operating experience of the prototype VK-50 reactor in RIAR, Dimitrovgrad, and the experience in designing such reactors as SBWR (GE) and SWR-1000 (Siemens). The CNPP's total power is planned to be 1000 MW(e) and district-heating heat production capacity 1600 Gcal/h. A detailed description of the results of the feasibility study is presented in the report. The results of the feasibility study have shown that the Archangelsk CGNP is feasible in terms of engineering, economics and production. (authors)

The results of feasibility study of co-generation NPP with innovative VK-300 simplified boiling water reactor

International Nuclear Information System (INIS)

Kuznetsov, Yu. N.; Gabaraev, B. A.

2004-01-01

The co-generation nuclear power plant (CNPP) producing electricity and district-heating heat is planned to be constructed in Archangelsk Region of Russia. Following the Letter of Intent signed by Governor of Archangelsk region and by Minister of the Russian Federation for atomic energy the feasibility study of the Project has been done. The NPP will be based on the four co-generation nuclear power units with the Russian VK-300 SBWR. The innovative passive VK-300 reactor facility has been designed on the basis of well-established nuclear technologies, proven major components, the operating experience of the prototype VK-50 reactor in RIAR, Dimitrovgrad, and the experience in designing such reactors as SBWR (GE) and SWR-1000 (Siemens). The CNPP's total power is planned to be 1000 MW(e) and district-heating heat production capacity 1600 Gcal /h. A detailed description of the results of the feasibility study is presented in the report. The results of the feasibility study have shown that the Archangelsk CGNP is feasible in terms of engineering, economics and production.(author)

A feasibility study on nuclear power options in Mongolia

International Nuclear Information System (INIS)

Minato, A.; Sekimoto, H.; Amartaivan, T.

2010-10-01

There is a growing interest among utilities in the United States in small and medium reactors due primarily to the smaller investment and perhaps shorter construction time involved as compared to those large reactors. The potential market for small reactors (those below 300 M We) exists, specially with sizes of 50 and 100 M We. A feasibility study was conducted on nuclear power options for Ulaanbaatar, Mongolia, a country which has a potential market for small reactors. The study was focused on an optimization of a combination of coal-fired and nuclear power plants taking into account Mongolia's future nuclear program plan, future population and economic growth, and the increased electricity and district heating demands. (Author)

Renewable energy technology feasibility study for a new hotel building in Amsterdam

NARCIS (Netherlands)

Bischoff, J.M.A.; Hensen, J.L.M.; Hassan Mohamed, Mohamed; Philips, C.

2016-01-01

This article discusses the economic and environmental feasibility of applying renewable energy technology (RET) to a new hotel building in Amsterdam using the simulation software HOMER. The study shows that applying PV including a surface up to 750m² can be both economical and environmentally

Tailored Communications for Obesity Prevention in Pediatric Primary Care: A Feasibility Study

Science.gov (United States)

Wright, Julie A.; Whiteley, Jessica A.; Watson, Bonnie L.; Sheinfeld Gorin, Sherri N.; Hayman, Laura L.

2018-01-01

Recommendations for the prevention of childhood obesity encourage providers to counsel parents and their children on healthy diet and activity behaviors. This study evaluated the feasibility of a theory-based, tailored communication intervention for obesity prevention ("Team Up for Health") delivered during a well-child visit. A…

Homogeneous slowpoke reactor for the production of radio-isotope. A feasibility study

International Nuclear Information System (INIS)

Busatta, P.; Bonin, H.

2005-01-01

The purpose of this research is to study the feasibility of replacing the actual heterogeneous fuel core of the present SLOWPOKE-2 by a reservoir containing a homogeneous fuel for the production of Mo-99. The study looked at three items: by using the MCNP 5 simulation code, develop a series of parameters required for an homogeneous fuel and evaluate the uranyl sulfate concentration of the aqueous solution fuel in order to keep a similar excess reactivity; verify if the homogeneous reactor will retain its inherent safety attributes; and with the new dimensions and geometry of the fuel core, observe whether the natural convection will still effectively cool the reactor using the modeling software FEMLAB. The MCNP 5 simulation code was validated by using a simulation with WIMS-AECL code. It was found that it is indeed feasible to modify the SLOWPOKE-2 reactor for a homogeneous reactor using a solution of uranyl sulfate and water. (author)

Homogeneous slowpoke reactor for the production of radio-isotope. A feasibility study

Energy Technology Data Exchange (ETDEWEB)

Busatta, P.; Bonin, H. [Royal Military College of Canada, Kingston, Ontario (Canada)]. E-mail: paul.busatta@rmc.ca; bonin-h@rmc.ca

2005-07-01

The purpose of this research is to study the feasibility of replacing the actual heterogeneous fuel core of the present SLOWPOKE-2 by a reservoir containing a homogeneous fuel for the production of Mo-99. The study looked at three items: by using the MCNP 5 simulation code, develop a series of parameters required for an homogeneous fuel and evaluate the uranyl sulfate concentration of the aqueous solution fuel in order to keep a similar excess reactivity; verify if the homogeneous reactor will retain its inherent safety attributes; and with the new dimensions and geometry of the fuel core, observe whether the natural convection will still effectively cool the reactor using the modeling software FEMLAB. The MCNP 5 simulation code was validated by using a simulation with WIMS-AECL code. It was found that it is indeed feasible to modify the SLOWPOKE-2 reactor for a homogeneous reactor using a solution of uranyl sulfate and water. (author)

A feasibility study of the offshore disposal of radioactive waste by drilled emplacement

International Nuclear Information System (INIS)

1984-01-01

This report describes the third phase of a study of the feasibility of disposal and isolation of high level radioactive waste in holes drilled deep into the sediments of the ocean. In this phase, work has concentrated on establishing the logistics of disposing of up to 400 cubic metres of vitrified waste per year, and on the capital and running costs of doing so. The report concludes that the disposal of waste in the form produced by the AVM process is operationally feasible, and that disposal in this way will add approximately 0.2% to the cost of generation of the energy contributing to the waste. (author)

Eye-tracking computer systems for inpatients with tetraplegia: findings from a feasibility study.

Science.gov (United States)

van Middendorp, J J; Watkins, F; Park, C; Landymore, H

2014-12-02

Study design:A longitudinal, prospective, self-controlled cohort study.Objectives:To determine (1) the preliminary benefits of using eye-tracking computer systems (ETCSs) among inpatients with tetraplegia and (2) the feasibility of carrying out a well-powered randomized controlled trial.Setting:Specialist Spinal Cord Injuries Centre, United Kingdom; 6 months during 2013-2014.Methods:Individuals with tetraplegia who were admitted to the center and enrolled in this study were trained and allowed to use the ETCS (Tobii Eyegaze C15 System) twice a week for a duration of 10 weeks. Standardized training modules were developed and offered to all study participants. Study feasibility indicators as well as the Appraisals of Disability: Primary and Secondary Scale, Hospital Anxiety and Depression Scale and the Assistive Technology Device Predisposition Assessment questionnaire scores were taken before and after study enrollment.Results:A total of 31 inpatients with tetraplegia were screened. Although 14 patients (45%) met the study eligibility criteria, 6 patients (19%) consented to be enrolled in the study. Three participants did not complete the planned training schedule because of medical, technical and logistic reasons. Although half of the participants agreed that the ETCS under study was easy to use, no substantial improvements were seen in terms of psychological outcomes, appraisals of disability or independence.Conclusions:The conduct of a controlled trial evaluating the benefits of using ETCSs among newly injured patients with tetraplegia comes with considerable feasibility challenges. Until substantial technical improvements of ETCSs have been implemented, future research should initially focus on those individuals with tetraplegia who are living in the community and who have expressed a need to enhance their computer access and communication skills.Spinal Cord advance online publication, 2 December 2014; doi:10.1038/sc.2014.219.

Summary of feasibility studies on in situ disposal as a decommissioning option for nuclear facilities

International Nuclear Information System (INIS)

Helbrecht, R.A.

2002-01-01

A scoping study was conducted over the period 1998-2000 to consider the feasibility of in situ disposal as a decommissioning option for AECL's Nuclear Power Demonstration Reactor located at Rolphton, Ontario. The results of a detailed assessment are summarized and the study concludes that in situ disposal appears feasible. Additional work required to confirm the results is also identified. A second in situ component, contaminated Winnipeg River sediments at AECL's Whiteshell Laboratory located in Manitoba, was also evaluated. That study concluded that in situ abandonment would have no adverse impact on aquatic life, humans and the environment. A summary of the study is presented as an appendix to the report. (author)

Economic feasibility study for improving drinking water quality: a case study of arsenic contamination in rural Argentina.

Science.gov (United States)

Molinos-Senante, María; Perez Carrera, Alejo; Hernández-Sancho, Francesc; Fernández-Cirelli, Alicia; Sala-Garrido, Ramón

2014-12-01

Economic studies are essential in evaluating the potential external investment support and/or internal tariffs available to improve drinking water quality. Cost-benefit analysis (CBA) is a useful tool to assess the economic feasibility of such interventions, i.e. to take some form of action to improve the drinking water quality. CBA should involve the market and non-market effects associated with the intervention. An economic framework was proposed in this study, which estimated the health avoided costs and the environmental benefits for the net present value of reducing the pollutant concentrations in drinking water. We conducted an empirical application to assess the economic feasibility of removing arsenic from water in a rural area of Argentina. Four small-scale methods were evaluated in our study. The results indicated that the inclusion of non-market benefits was integral to supporting investment projects. In addition, the application of the proposed framework will provide water authorities with more complete information for the decision-making process.

Fusion guidance in endovascular peripheral artery interventions: a feasibility study.

Science.gov (United States)

Sailer, Anna M; de Haan, Michiel W; de Graaf, Rick; van Zwam, Willem H; Schurink, Geert Willem H; Nelemans, Patricia J; Wildberger, Joachim E; Das, Marco

2015-04-01

This study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA). Fusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography. Average time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation). Fluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety.

Feasibility Study Evaluating Four Weeks Stochastic Resonance Whole-Body Vibration Training with Healthy Female Students

Directory of Open Access Journals (Sweden)

Slavko Rogan

2013-07-01

Full Text Available This study assessed the feasibility of stochastic resonance whole-body vibration (SR-WBV training and its impact on isometric maximal voluntary contraction (IMVC, isometric rate of force development (IRFD and a drop jump test (DJ in healthy female students. Twelve participants were randomised to static squats during SR-WBV 6 Hz, noise level 4, over 4 weeks or to a control group (no training. Feasibility outcomes included the number of students agreeing to participate, the number of drop-outs, the adherence to the SR-WBV and the evaluation of the protocol. Secondary outcomes were IMVC, IRFD and DJ. Results: Among 35 eligible students, 12 agreed to participate and two dropped out. The adherence was 41 of 60 possible sessions. There were moderate to large, but statistically non-significant, gains in the secondary outcomes. Conclusion: These results suggest that such a study would be feasible although with some modifications such as a better familiarisation to the DJ.

A neutronic feasibility study for LEU conversion of the Brookhaven Medical Research Reactor (BMRR).

Energy Technology Data Exchange (ETDEWEB)

Hanan, N. A.

1998-01-14

A neutronic feasibility study for converting the Brookhaven Medical Research Reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with Brookhaven National Laboratory. Two possible LEU cores were identified that would provide nearly the same neutron flux and spectrum as the present HEU core at irradiation facilities that are used for Boron Neutron Capture Therapy and for animal research. One core has 17 and the other has 18 LEU MTR-type fuel assemblies with uranium densities of 2.5g U/cm{sup 3} or less in the fuel meat. This LEU fuel is fully-qualified for routine use. Thermal hydraulics and safety analyses need to be performed to complete the feasibility study.

Pilot Feasibility Study of an Oncology Financial Navigation Program.

Science.gov (United States)

Shankaran, Veena; Leahy, Tony; Steelquist, Jordan; Watabayashi, Kate; Linden, Hannah; Ramsey, Scott; Schwartz, Naomi; Kreizenbeck, Karma; Nelson, Judy; Balch, Alan; Singleton, Erin; Gallagher, Kathleen; Overstreet, Karen

2018-02-01

Few studies have reported on interventions to alleviate financial toxicity in patients with cancer. We developed a financial navigation program in collaboration with our partners, Consumer Education and Training Services (CENTS) and Patient Advocate Foundation (PAF), to improve patient knowledge about treatment costs, provide financial counseling, and to help manage out-of-pocket expenses. We conducted a pilot study to assess the feasibility and impact of this program. Patients with cancer received a financial education course followed by monthly contact with a CENTS financial counselor and a PAF case manager for 6 months. We measured program adherence, self-reported financial burden and anxiety, program satisfaction, and type of assistance provided. Thirty-four patients (median age, 60.5 years) were consented (85% white and 50% commercially insured). Debt, income declines, and loans were reported by 55%, 55%, and 30% of patients, respectively. CENTS counselors assisted most often with budgeting, retirement planning, and medical bill questions. PAF case managers assisted with applications for appropriate insurance coverage, cost of living issues (eg, housing, transportation), and disability applications. High financial burden and anxiety about costs (4 or 5 on a Likert scale) were reported at baseline by 37% and 47% of patients, respectively. Anxiety about costs decreased over time in 33% of patients, whereas self-reported financial burden did not substantially change. Implementing an oncology financial navigation program is feasible, provides concrete assistance in navigating the cost of care, and mitigates anxiety about costs in a subset of patients. Future work will focus on measuring the program's impact on financial and clinical outcomes.

Effect of information feedback on training standing up following stroke: a pilot feasibility study.

Science.gov (United States)

Stanton, Rosalyn; Ada, Louise; Dean, Catherine M; Preston, Elisabeth

2016-12-01

The ability to stand up is reduced following stroke. Traditional biofeedback is effective in improving the performance of lower limb activities. The aim of this study was to investigate the feasibility of and potential for information feedback from a simple inexpensive device to improve the ability to stand up from a chair in people following stroke. A single-group study with pre-post measures design was used. Twenty people with hemiplegic stroke in inpatient rehabilitation received 10 sessions over 2 weeks of information feedback about foot placement during training of standing up. Progression involved increasing repetitions, increasing difficulty and fading feedback. Feasibility was determined by adherence, time taken, acceptability and safety. Clinical outcomes were the time taken to stand up, quality and foot position measured using the 5-Times-Sit-To-Stand-Test and carryover into daily activities measured by covert observation. The study was feasible with 97% of sessions completed, taking 19 (SD 6) to 25 (SD 10) minutes. Participants understood (4.6/5), found useful (4.6/5), challenging (4.4/5) and would recommend (4.7/5) the training. The time to stand up 5 times decreased by 24 (95% CI -48 to -1) s, and the quality of standing improved by 1.0/10.0 (95% CI 0.2 to 1.8). Carryover of the correct foot placement occurred to real life, with the beginning foot position correct 2.1/3.0 (95% CI 1.6 to 2.6) and end foot position correct 1.8/3.0 (95% CI 1.2 to 2.4) occasions. The training is feasible and has the potential to improve the ability to stand up.

Long-range eye tracking: A feasibility study

Energy Technology Data Exchange (ETDEWEB)

Jayaweera, S.K.; Lu, Shin-yee

1994-08-24

The design considerations for a long-range Purkinje effects based video tracking system using current technology is presented. Past work, current experiments, and future directions are thoroughly discussed, with an emphasis on digital signal processing techniques and obstacles. It has been determined that while a robust, efficient, long-range, and non-invasive eye tracking system will be difficult to develop, such as a project is indeed feasible.

Northern gas: Williams petrochemical feasibility study

Energy Technology Data Exchange (ETDEWEB)

Chappell, D. [Williams Energy Canada, Calgary, AB (Canada)

2002-07-01

Williams Energy is a company that is involved in the following fields: gas pipelines, exploration and production, midstream, refining, petrochemical, power, and marketing and trading. The author provides an overview of the global and Canadian infrastructure before proceeding to discuss Arctic gas, which is viewed by Williams Energy as necessary. It favors the Alaska Highway route with a consortium for project development. Williams performed a petrochemical study to determine the feasibility of a petrochemical complex utilizing natural gas liquid from an Arctic gas pipeline. The scope of the study encompassed facilities (extraction plant, cracker, polyolefins plant), size (world scale, approximately 2 billion pounds per year), and location (Fairbanks or Alberta). The study led to the following findings: (1) review of several scenarios for both locations, (2) complex to produce two grades of polyethylene, (3) feedstock cost favors Alaska, (4) construction costs lower in Alberta, (5) and the primary market for the Alaska complex would be northeast Asia, while the primary market for the Alberta location would be the United States. It was determined that both options would be viable, however Alberta was favored due to the polyethylene forecast. The challenges still being faced by Williams include low frac spread, market inefficiencies, empress volumes, carbon dioxide, and fuel and electricity cost. Each of these challenges is discussed separately. The author concludes by indicating that incremental ethane is available, carbon dioxide issues need resolution, and Alberta and Alaska are attractive for Arctic ethane petrochemical production. figs.

Understanding Patient Experience Using Internet-based Email Surveys: A Feasibility Study at Mount Sinai Hospital.

Science.gov (United States)

Morgan, Matthew; Lau, Davina; Jivraj, Tanaz; Principi, Tania; Dietrich, Sandra; Bell, Chaim M

2015-01-01

Email is becoming a widely accepted communication tool in healthcare settings. This study sought to test the feasibility of Internet-based email surveys of patient experience in the ambulatory setting. We conducted a study of email Internet-based surveys sent to patients in selected ambulatory clinics at Mount Sinai Hospital in Toronto, Canada. Our findings suggest that email links to Internet surveys are a feasible, timely and efficient method to solicit patient feedback about their experience. Further research is required to optimally leverage Internet-based email surveys as a tool to better understand the patient experience.

Case study on the feasibility of small and medium nuclear power plants in Egypt

International Nuclear Information System (INIS)

1994-04-01

The IAEA agreed to co-operate with the Arab Republic of Egypt in performing a case study on the feasibility of small and medium power reactors (SMPRs) as a technical assistance project. The major objective of this study is to examine the feasibility of SMPRs to supply a portion of the future electrical energy requirements in the long term power programme of Egypt. The IAEA is grateful to all who provided information and assisted in the drafting and review of the report, in particular to the Advisory Group which performed the study in a co-operative effort. It is hoped that the report will meet the interests of policy makers, managers, engineers and economists in Member States, particularly in developing countries, and that it will provide a useful basis for specific studies to prepare decisions on SMPR projects. Refs, figs and tabs

MODAS. Feasibility Study for Implementation of V-TECS Occupational Data Analysis System (ODAS).

Science.gov (United States)

Illinois State Occupational Information Coordinating Committee, Springfield.

This feasibility study was conducted to determine if the Michigan Occupational Data Analysis System (MODAS) can be implemented or modified in Illinois by studying the information needs of state agencies and local educational institutions. Agencies were asked how they might use the MODAS system for activities such as curriculum development and…

100-HR-1 Operable Unit focused feasibility study report. Draft A

International Nuclear Information System (INIS)

1994-09-01

The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 Feasibility Study (FS) includes development and screening of alternatives (phases 1 and 2) and the detailed analysis of alternatives (phase 3). This focused feasibility study (FFS) constitutes the phase 3 portion of the FS process. The FFS process is conducted in two stages, a Process Document (DOE-RL 1994a) and an operable unit-specific FFS document, such as this one. The FFS process is performed by implementing a ''plug-in'' style approach as defined in great detail in the Process Document. The objective of this operable unit-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for sites associated with the 100-HR-1 Operable Unit. The IRM candidate waste sites are determined in the limited field investigation. Site profiles are developed for each of these waste sites. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

FEASIBILITY STUDY FOR A PETROLEUM REFINERY FOR THE JICARILLA APACHE TRIBE

International Nuclear Information System (INIS)

Jones, John D.

2004-01-01

A feasibility study for a proposed petroleum refinery for the Jicarilla Apache Indian Reservation was performed. The available crude oil production was identified and characterized. There is 6,000 barrels per day of crude oil production available for processing in the proposed refinery. The proposed refinery will utilize a lower temperature, smaller crude fractionation unit. It will have a Naphtha Hydrodesulfurizer and Reformer to produce high octane gasoline. The surplus hydrogen from the reformer will be used in a specialized hydrocracker to convert the heavier crude oil fractions to ultra low sulfur gasoline and diesel fuel products. The proposed refinery will produce gasoline, jet fuel, diesel fuel, and a minimal amount of lube oil. The refinery will require about $86,700,000 to construct. It will have net annual pre-tax profit of about $17,000,000. The estimated return on investment is 20%. The feasibility is positive subject to confirmation of long term crude supply. The study also identified procedures for evaluating processing options as a means for American Indian Tribes and Native American Corporations to maximize the value of their crude oil production

Pneumatic artificial muscles for trailing edge flap actuation: a feasibility study

Science.gov (United States)

Woods, Benjamin K. S.; Kothera, Curt S.; Sirohi, Jayant; Wereley, Norman M.

2011-10-01

In this study a novel aircraft trailing edge flap actuation system was developed and tested. Pneumatic artificial muscles (PAMs) were used as the driving elements of this system to demonstrate their feasibility and utility as an alternative aerospace actuation technology. A prototype flap/actuator system was integrated into a model wing section and tested on the bench-top under simulated airloads for flight at 100 m s-1 (M = 0.3) and in an open-jet wind tunnel at free stream velocities ranging up to 45 m s-1 (M = 0.13). Testing was performed for actuator pressures ranging from 0.069 to 0.62 MPa (10-90 psi) and actuation frequencies from 0.1 to 31 Hz. Results show that the PAM-driven trailing edge flap system can generate substantial and sustainable dynamic deflections, thereby proving the feasibility of using pneumatic artificial muscle actuators in a trailing edge flap system. Key issues limiting system performance are identified, that should be resolved in future research.

Economic feasibility study of potato preservation by irradiation in saudi arabia

Energy Technology Data Exchange (ETDEWEB)

Kinsara, A A; Abulfaraj, W H; Mamoon, A M; Kamal, S E [Nuclear Engineering Department, Faculty of Engineering, King Abdulaziz University, Jeddah (Saudi Arabia)

1997-12-31

Comprehensive studies were carried out to investigate the economic feasibility of the preservation of potato crop by cobalt-60 gamma irradiation sprout inhibition by potato irradiation was approved by international organization and concerned authorities in many countries. The dose level range authorized for potato sprout inhibition extends from about 80-150 Gy depending on potato variety, time of irradiation after harvest, and post irradiation storage temperature. Sprout inhibition is most effective by irradiation after harvest, and after healing of any inflicted injuries, that when the potatoes are dormant. Irradiation at the recommended doses minimizes storage losses of potatoes that are refrigerated or stored on shelves. Despite the limited data available, an attempt was made to quantify the monetary value of preserving potato by irradiation. With economy scale taken in consideration, potato preservation by irradiation is economically feasible since at the local consumption rates there will be lot of potatoes that ned storage for off season use. 5 tabs.

The Ronnie Gardiner Rhythm and Music Method - a feasibility study in Parkinson's disease.

Science.gov (United States)

Pohl, Petra; Dizdar, Nil; Hallert, Eva

2013-01-01

To assess the feasibility of the novel intervention, Ronnie Gardiner Rhythm and Music (RGRM™) Method compared to a control group for patients with Parkinson's disease (PD). Eighteen patients, mean age 68, participating in a disability study within a neurological rehabilitation centre, were randomly allocated to intervention group (n = 12) or control group (n = 6). Feasibility was assessed by comparing effects of the intervention on clinical outcome measures (primary outcome: mobility as assessed by two-dimensional motion analysis, secondary outcomes: mobility, cognition, quality of life, adherence, adverse events and eligibility). Univariable analyses showed no significant differences between groups following intervention. However, analyses suggested that patients in the intervention group improved more on mobility (p = 0.006), cognition and quality of life than patients in the control group. There were no adverse events and a high level of adherence to therapy was observed. In this disability study, the use of the RGRM™ Method showed promising results in the intervention group and the adherence level was high. Our results suggest that most assessments chosen are eligible to use in a larger randomized controlled study for patients with PD. The RGRM™ Method appeared to be a useful and safe method that showed promising results in both motor and cognitive functions as well as quality of life in patients with moderate PD. The RGRM™ Method can be used by physiotherapists, occupational, speech and music therapists in neurological rehabilitation. Most measurements were feasible except for Timed-Up-and-Go.

Dual-Doppler Feasibility Study

Science.gov (United States)

Huddleston, Lisa L.

2012-01-01

When two or more Doppler weather radar systems are monitoring the same region, the Doppler velocities can be combined to form a three-dimensional (3-D) wind vector field thus providing for a more intuitive analysis of the wind field. A real-time display of the 3-D winds can assist forecasters in predicting the onset of convection and severe weather. The data can also be used to initialize local numerical weather prediction models. Two operational Doppler Radar systems are in the vicinity of Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS); these systems are operated by the 45th Space Wing (45 SW) and the National Weather Service Melbourne, Fla. (NWS MLB). Dual-Doppler applications were considered by the 45 SW in choosing the site for the new radar. Accordingly, the 45th Weather Squadron (45 WS), NWS MLB and the National Aeronautics and Space Administration tasked the Applied Meteorology Unit (AMU) to investigate the feasibility of establishing dual-Doppler capability using the two existing systems. This study investigated technical, hardware, and software requirements necessary to enable the establishment of a dual-Doppler capability. Review of the available literature pertaining to the dual-Doppler technique and consultation with experts revealed that the physical locations and resulting beam crossing angles of the 45 SW and NWS MLB radars make them ideally suited for a dual-Doppler capability. The dual-Doppler equations were derived to facilitate complete understanding of dual-Doppler synthesis; to determine the technical information requirements; and to determine the components of wind velocity from the equation of continuity and radial velocity data collected by the two Doppler radars. Analysis confirmed the suitability of the existing systems to provide the desired capability. In addition, it is possible that both 45 SW radar data and Terminal Doppler Weather Radar data from Orlando International Airport could be used to alleviate any

Laboratory and Feasibility Study for Industrial Wastewater Effluents Treatment by Radiation

Energy Technology Data Exchange (ETDEWEB)

Zimek, Z.; Głuszewski, W. [Centre for Radiation Research and Technology, Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

2012-07-01

The study of wastewater treatment by radiation regarding chemical processes contribution and physical-chemical separation of highly concentrated non-organic pollutants deposited in specific industrial waste are proposed. Laboratory stand should be build and the study should be performed to confirm possible mechanism of the sedimentation process of nonorganic pollutants during separation initiated by ionizing radiation. Evaluation from technical and economical point of view of this specific radiation technology and feasibility study preparation for industrial facility will be the main output at the final stage of the project. (author)

Laboratory and Feasibility Study for Industrial Wastewater Effluents Treatment by Radiation

International Nuclear Information System (INIS)

Zimek, Z.; Głuszewski, W.

2012-01-01

The study of wastewater treatment by radiation regarding chemical processes contribution and physical-chemical separation of highly concentrated non-organic pollutants deposited in specific industrial waste are proposed. Laboratory stand should be build and the study should be performed to confirm possible mechanism of the sedimentation process of nonorganic pollutants during separation initiated by ionizing radiation. Evaluation from technical and economical point of view of this specific radiation technology and feasibility study preparation for industrial facility will be the main output at the final stage of the project. (author)

Strategic analysis for safeguards systems: a feasibility study. Volume 1. Main report

International Nuclear Information System (INIS)

Seaver, D.A.; Cohen, M.S.; Immerman, W.H.; Crane, F.L.; Goldman, A.J.

1984-12-01

Strategic analysis (game theory) is a formal method for modeling adversary situations that, when solved, yields an optimal strategy that maximizes the expected payoff to the player. As such, it appears to be potentially applicable in the nuclear material accounting context in which there is potential for an adversary attempting to divert special nuclear material. The NRC has previously supported research to develop preliminary strategic analysis models which has been considered to be only partially successful. This study reviewed previous efforts and other game theory research and assessed the feasibility of: (1) applying strategic analysis in a regulatory framework; (2) making strategic analysis understandable by licensees; and (3) assuring that strategic analysis can effectively be enforced. This report includes a discussion of the role of strategic analysis in material control and accounting, and of the mechanisms by which the NRC could implement strategic analysis. A set of feasibility criteria are described including both technical feasibility and organizational/implementation feasibility. Alternative strategic analysis model options are evaluated with respect to these criteria, as is the current material accounting practice. The assessment determined that the development of a payoff function that adequately represented the NRC's (and therefore the public's) values with respect to the consequences of diversion and the actions taken to prevent it is the most serious impediment to implementation. Given the limited role of material accounting in safeguards and the uncertainty regarding the development of a payoff function, the NRC should not proceed with full-scale implementation of strategic analysis. It does, however, have sufficient potential to warrant further development, with first priority going to the development of an appropriate payoff function

Feasibility study of a fission supressed blanket for a tandem-mirror hybrid reactor

International Nuclear Information System (INIS)

Moir, R.W.; Lee, J.D.; Barr, W.L.

1981-01-01

A study of fission suppressed blankets for the tandem mirror not only showed such blankets to be feasible but also to be safer than fissioning blankets. Such hybrids could produce enough fissile material to support up to 17 light water reactors of the same nuclear power rating. Beryllium was compared to 7 Li for neutron multiplication; both were considered feasible but the blanket with Li produced 20% less fissile fuel per unit of nuclear power in the reactor. The beryllium resource, while possibly being too small for extensive pure fusion application, would be adequate (with carefully planned industrial expansion) for the hybrid because of the large support ratio, and hence few hybrids required. Radiation damage and coatings for beryllium remain issues to be resolved by further study and experimentation. Molten salt reprocessing was compared to aqueous solution reprocessing

Producing Hardwood Dimension Parts Directly From Logs: An Economic Feasibility Study

Science.gov (United States)

Wenjie Lin; D. Earl Kline; Philip A. Araman; Janice K. Wiedenbeck

1995-01-01

The economic feasibility and profitability of a direct processing system for converting Factory Grades 2 and 3 red oak logs directly into rough dimension parts were evaluated. New present value (NPV) and internal rate of return (IRR) were used as the measurement of economic feasibility, and return on sales (ROS) was used as the measurement of profitability. NPV and IRR...

Preliminary study of environmental parameters associated with the feasibility of a polygeneration plant at Kennedy Space Center

International Nuclear Information System (INIS)

Barnes, G.D.

1982-01-01

The feasibility of a polygeneration plant at Kennedy Space Center was studied. Liquid hydrogen and gaseous nitrogen are the two principal products in consideration. Environmental parameters (air quality, water quality, biological diversity and hazardous waste disposal) necessary for the feasibility study were investigated. A National Environmental Policy Act (NEPA) project flow sheet was to be formulated for the environmental impact statement. Water quality criteria for Florida waters were to be established

GINGER: A feasibility study

Science.gov (United States)

Di Virgilio, Angela D. V.; Belfi, Jacopo; Ni, Wei-Tou; Beverini, Nicolo; Carelli, Giorgio; Maccioni, Enrico; Porzio, Alberto

2017-04-01

GINGER (Gyroscopes IN General Relativity) is a proposal for an Earth-based experiment to measure the Lense-Thirring (LT) and de Sitter effects. GINGER is based on ring lasers, which are the most sensitive inertial sensors to measure the rotation rate of the Earth. We show that two ring lasers, one at maximum signal and the other horizontal, would be the simplest configuration able to retrieve the GR effects. Here, we discuss this configuration in detail showing that it would have the capability to test LT effect at 1%, provided the accuracy of the scale factor of the instrument at the level of 1 part in 1012 is reached. In principle, one single ring laser could do the test, but the combination of the two ring lasers gives the necessary redundancy and the possibility to verify that the systematics of the lasers are sufficiently small. The discussion can be generalised to seismology and geodesy and it is possible to say that signals 10-12 orders of magnitude below the Earth rotation rate can be studied; the proposed array can be seen as the basic element of multi-axial systems, and the generalisation to three dimensions is feasible adding one or two devices and monitoring the relative angles between different ring lasers. This simple array can be used to measure with very high precision the amplitude of angular rotation rate (the length of the day, LOD), its short term variations, and the angle between the angular rotation vector and the horizontal ring laser. Finally this experiment could be useful to probe gravity at fundamental level giving indications on violations of Einstein Equivalence Principle and Lorenz Invariance and possible chiral effects in the gravitational field.

A feasibility study for a one-megawatt pulsed spallation source at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Pynn, R.

1994-01-01

Over the past two decades, high-intensity proton accelerators have been designed and developed to support nuclear physics research and defense applications. This technology has now matured to the point where it can support simultaneous and cost-effective exploitation of a number of important areas of both basic and applied science. Examples include neutron scattering, the production of radioisotopes, tests of technologies to transmute nuclear waste, radiation damage studies, nuclear physics, and muon spin research. As part of a larger program involving these and other areas, a team at Los Alamos National Laboratory has undertaken a feasibility study for a 1-MW pulsed spallation neutron source (PSS) based on the use of an 800-MeV proton linac and an accumulator ring. In January 1994, the feasibility study was reviewed by a large, international group of experts in the design of accelerators and neutron spallation targets. This group confirmed the viability of the proposed neutron source. In this paper, I describe the approach Los Alamos has taken to the feasibility study, which has involved a synergistic application of the Laboratory's expertise in nuclear science and technology, computation, and particle-beam technologies. Several examples of problems resolved by the study are described, including chopping of low-energy proton beam, interactions between H - particles and the stripper foil used to produce protons for injection into an accumulator ring, and the inclusion of engineering realities into the design of a neutron production target. These examples are chosen to illustrate the breadth of the expertise that has been brought to bear on the feasibility study and to demonstrate that there are real R ampersand D issues that need to be resolved before a next-generation spoliation source can be built

Web-based symptom screening in cystic fibrosis patients: A feasibility study.

Science.gov (United States)

Balzano, Julie; Fresenius, Ashley; Walker, Patricia; Berdella, Maria; Portenoy, Russell K; Bookbinder, Marilyn; Glajchen, Myra; Plachta, Amy; Langfelder-Schwind, Elinor; Chen, Jack; Dhingra, Lara

2016-01-01

Cystic fibrosis (CF) causes high illness burden. Screening may identify patients who could potentially benefit from interventions for symptoms or other sources of distress. We evaluated the feasibility of a web-based system for routine monitoring. Adult CF patients enrolled in a study of palliative care service delivery completed web-based assessments every 30 days on global distress, physical and psychological symptom distress, and the perceived benefits of discussing advance care planning (ACP) with CF clinicians. Feasibility was assessed by the rate of survey completion, survey reminders, and missed surveys during a 9-month rolling enrollment period. Of 74 participants (47.3% women, 94.4% white), 36.7% had comorbid diabetes, and 56.9% had an FEV1% predicted score of 40-69. In total, patients completed 456 (80.6%) of 566 surveys every 30 days over the assessment period. Sixty-five (87.8%) completed 405 (79.7%) of 508 surveys online and 9 (12.2%) completed 51 (88.0%) of 58 surveys using a combination of online, telephone, and mail-based methods. Many surveys were completed without reminders (online: 261 [64.4%] of 405; combined methods: 29 [56.9%] of 51), with 166 (36.4%) surveys requiring 1 or more reminders. Further, 23.0% (17) of patients noted elevated global distress; 20.3% (15) endorsed physical symptom distress, 12.2% (9) had psychological distress, and 58.1% (43) reported that discussing ACP would be beneficial. Repeated web-based screening for symptom distress and ACP preferences is feasible in adult CF patients. Future studies should assess the system's generalizability and staff resources when implementing reminders and non-web methods of completion. Copyright © 2015 European Cystic Fibrosis Society. All rights reserved.

A feasibility study of a linear laser heated solenoid fusion reactor. Final report

International Nuclear Information System (INIS)

Steinhauer, L.C.

1976-02-01

This report examines the feasibility of a laser heated solenoid as a fusion or fusion-fission reactor system. The objective of this study, was an assessment of the laser heated solenoid reactor concept in terms of its plasma physics, engineering design, and commercial feasibility. Within the study many pertinent reactor aspects were treated including: physics of the laser-plasma interaction; thermonuclear behavior of a slender plasma column; end-losses under reactor conditions; design of a modular first wall, a hybrid (both superconducting and normal) magnet, a large CO 2 laser system; reactor blanket; electrical storage elements; neutronics; radiation damage, and tritium processing. Self-consistent reactor configurations were developed for both pure fusion and fusion-fission designs, with the latter designed both to produce power and/or fissile fuels for conventional fission reactors. Appendix A is a bibliography with commentary of theoretical and experimental studies that have been directed at the laser heated solenoid

The effect of targeted treatment on people with patellofemoral pain: a pragmatic, randomised controlled feasibility study.

Science.gov (United States)

Drew, Benjamin T; Conaghan, Philip G; Smith, Toby O; Selfe, James; Redmond, Anthony C

2017-08-04

Targeted treatment, matched according to specific clinical criteria e.g. hip muscle weakness, may result in better outcomes for people with patellofemoral pain (PFP). However, to ensure the success of future trials, a number of questions on the feasibility of a targeted treatment need clarification. The aim of the study was to explore the feasibility of matched treatment (MT) compared to usual care (UC) management for a subgroup of people with PFP determined to have hip weakness and to explore the mechanism of effect for hip strengthening. In a pragmatic, randomised controlled feasibility study, 24 participants with PFP (58% female; mean age 29 years) were randomly allocated to receive either MT aimed specifically at hip strengthening, or UC over an eight-week period. The primary outcomes were feasibility outcomes, which included rates of adherence, attrition, eligibility, missing data and treatment efficacy. Secondary outcomes focused on the mechanistic outcomes of the intervention, which included hip kinematics. Conversion to consent (100%), missing data (0%), attrition rate (8%) and adherence to both treatment and appointments (>90%) were deemed successful endpoints. The analysis of treatment efficacy showed that the MT group reported a greater improvement for the Global Rating of Change Scale (62% vs. 9%) and the Anterior Knee Pain Scale (-5.23 vs. 1.18) but no between-group differences for either average or worst pain. Mechanistic outcomes showed a greatest reduction in peak hip internal rotation angle for the MT group (13.1% vs. -2.7%). This feasibility study indicates that a definitive randomised controlled trial investigating a targeted treatment approach is achievable. Findings suggest the mechanism of effect of hip strengthening may be to influence kinematic changes in hip function in the transverse plane. This study was registered retrospectively. ISRCTN74560952 . Registration date: 2017-02-06.

Feasibility design study. Land-based OTEC plants. Final report

Energy Technology Data Exchange (ETDEWEB)

Brewer, J. H.; Minor, J.; Jacobs, R.

1979-01-01

The purpose of this study has been to determine the feasibility of installing 10 MWe (MegaWatt-electric) and 40 MWe land-based OTEC demonstration power plants at two specific sites: Keahole Point on the western shore of the island of Hawaii; and Punta Tuna, on the southeast coast of the main island of Puerto Rico. In addition, the study has included development of design parameters, schedules and budgets for the design, construction and operation of these plants. Seawater systems (intake and discharge pipes) were to be sized so that flow losses were equivalent to those expected with a platform-based OTEC power plant. The power module (components and general arrangement was established based on the TRW design. Results are presented in detail. (WHK)

B Plant process piping replacement feasibility study

International Nuclear Information System (INIS)

Howden, G.F.

1996-01-01

Reports on the feasibility of replacing existing embedded process piping with new more corrosion resistant piping between cells and between cells and a hot pipe trench of a Hanford Site style canyon facility. Provides concepts for replacement piping installation, and use of robotics to replace the use of the canyon crane as the primary means of performing/supporting facility modifications (eg, cell lining, pipe replacement, equipment reinstallation) and operational maintenenace

Report on feasibility study of the Clam Wave Energy Device

Energy Technology Data Exchange (ETDEWEB)

1979-04-01

The main emphasis of the feasibility study has been towards producing an acceptable spine design for the Clam wave energy converter. Concrete and steel designs based on a mathematical model of the waveloading have been produced. Progress is also reported in the design of a bellows for a low-pressure air power transmission system. A narrow wave tank and scale model have been constructed in order to carry out a test programme on various aspects of the device's construction and performance.

Report on feasibility study of energy-saving visions for City of Mitaka; Mitaka-shi sho energy vision feasibility study hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

The feasibility study is implemented to concretely promote the project for the (new energy/energy-saving visions for the City of Mitaka area) aimed at abatement of green effect gases which cause global warming, for which the public facilities are investigated to collect information related to the energy-saving project, and the implementation schemes are studied from the operational and fund aspects. A total of 60 public facilities in the city are studied for energy-saving potentials and their characteristics through the questionnaires and simulation, and placed in the order of priority. The project implementation simulation is conducted, to grasp the long-term energy-saving effect, energy cost reduction and CO2 abatement potentials, if the project is actually implemented. The studies on the 10 facilities indicate that power consumption can be possibly reduced by 1.45 million kWh in the initial year, and the accumulated introduction and abatement costs indicate that the project will produce the first profit of around 49 million yen in 2012. CO2 can be abated by 230 tons-C/year on the average during the 2008 to 2012 period. (NEDO)

Phase I feasibility study for the Canyon disposition initiative (221-U facility)

International Nuclear Information System (INIS)

1997-08-01

The objective of the Phase I Feasibility Study (FS) presented in this document is to provide decision makers sufficient information on the remedial alternatives specific to the disposition of the 221-U Canyon Building (221-U Facility) located at the Hanford Site, and to determine which alternatives are viable for further detailed analysis

Feasibility study on thermal-hydraulic design of reduced-moderation PWR-type core

International Nuclear Information System (INIS)

Yoshida, Hiroyuki; Ohnuki, Akira; Akimoto, Hajime

2000-03-01

At JAERI, a conceptual study on reduced-moderation water reactor (RMWR) has been performed as one of the advanced reactor system which is designed so as to realize the conversion ratio more than unity. In this reactor concept, the gap spacing between the fuel rods is remarkably narrower than in a reactor currently operated. Therefore, an evaluation of the core thermal margin becomes very important in the design of the RMWR. In this study, we have performed a feasibility evaluation on thermal-hydraulic design of RM-PWR type core (core thermal output: 2900 MWt, Rod gaps: 1 mm). In RM-PWR core, seed and blanket regions are exist. In the blanket region, power density is lower than that of the seed region. Then, evaluation was performed under setting a channel box to each fuel assembly in order to adjust the flow rate in each assembly, because it is possible that the coolant boils in the seed region. In the feasibility evaluations, subchannel code COBRA-IV-I was used in combination with KfK DNB (departure nucleate boiling) correlation. When coolant mass flow rate to the blanket fuel assembly is reduced by 40%, and that to the seed fuel assembly is increased, coolant boiling is not occurred in the assembly region calculation. Provided that the channel boxes to the blanket fuel assembly are set up and coolant mass flow rate to the blanket fuel assembly is reduced by 40%, it is confirmed by the whole core calculation that the boiling of the coolant is not occurred and the RM-PWR core is feasible. (author)

Pinellas Plant feasibility study. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases.

Automated docking screens: a feasibility study.

Science.gov (United States)

Irwin, John J; Shoichet, Brian K; Mysinger, Michael M; Huang, Niu; Colizzi, Francesco; Wassam, Pascal; Cao, Yiqun

2009-09-24

Molecular docking is the most practical approach to leverage protein structure for ligand discovery, but the technique retains important liabilities that make it challenging to deploy on a large scale. We have therefore created an expert system, DOCK Blaster, to investigate the feasibility of full automation. The method requires a PDB code, sometimes with a ligand structure, and from that alone can launch a full screen of large libraries. A critical feature is self-assessment, which estimates the anticipated reliability of the automated screening results using pose fidelity and enrichment. Against common benchmarks, DOCK Blaster recapitulates the crystal ligand pose within 2 A rmsd 50-60% of the time; inferior to an expert, but respectrable. Half the time the ligand also ranked among the top 5% of 100 physically matched decoys chosen on the fly. Further tests were undertaken culminating in a study of 7755 eligible PDB structures. In 1398 cases, the redocked ligand ranked in the top 5% of 100 property-matched decoys while also posing within 2 A rmsd, suggesting that unsupervised prospective docking is viable. DOCK Blaster is available at http://blaster.docking.org .

Pinellas Plant feasibility study. Final report

International Nuclear Information System (INIS)

1994-09-01

The Pinellas Plant was built in 1956 to manufacture neutron generators, a principal component in nuclear weapons. In September 1990, the Department of Health and Rehabilitative Services (HRS) entered into an agreement with DOE to independently examine environmental monitoring data from the plant and health data from Pinellas County to determine if an epidemiological study is technically feasible to measure possible off-site health effects from ionizing radiation. Through normal plant operations, some radioactive materials have been released to the environment. Eighty percent of the total plant releases of 107,707 curies occurred in the early years of plant operation (1957--1960). The primary materials released were tritium gas, tritium oxide and krypton-85. Environmental monitoring for radioactive releases from the plant has been done regularly since 1975. The US Public Health Service Centers for Disease Control and Prevention (CDC), in assisting HRS, has determined that sufficient radiological data exist by which a dose reconstruction can be done. A dose reconstruction can provide an estimate of how much radiological exposure someone living in the vicinity of the Pinellas Plant may have suffered from environmental releases

Remedial investigation/feasibility study of the Clinch River/Poplar Creek operable unit. Volume 4. Information related to the feasibility study and ARARs. Appendixes G, H, I

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report presents the findings of an investigation into contamination of the Clinch River and Poplar Creek near the U.S. Department of Energy`s (DOE`s) Oak Ridge Reservation (ORR) in eastern Tennessee. For more than 50 years, various hazardous and radioactive substances have been released to the environment as a result of operations and waste management activities at the ORR. In 1989, the ORR was placed on the National Priorities List (NPL), established and maintained under the federal Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under CERCLA, NPL sites must be investigated to determine the nature and extent of contamination at the site, assess the risk to human health and the environment posed by the site, and, if necessary, identify feasible remedial alternatives that could be used to clean the site and reduce risk. To facilitate the overall environmental restoration effort at the ORR, CERCLA activities are being implemented individually as distinct operable units (OUs). This document is the combined Remedial Investigation and Feasibility Study Report for the Clinch River/Poplar Creek OU.

Fusion Guidance in Endovascular Peripheral Artery Interventions: A Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

Sailer, Anna M., E-mail: anni.sailer@mumc.nl; Haan, Michiel W. de, E-mail: m.de.haan@mumc.nl; Graaf, Rick de, E-mail: r.de.graaf@mumc.nl; Zwam, Willem H. van, E-mail: w.van.zwam@mumc.nl [Maastricht University Medical Center, Department of Radiology (Netherlands); Schurink, Geert Willem H., E-mail: gwh.schurink@mumc.nl [Maastricht University Medical Center, Department of Surgery (Netherlands); Nelemans, Patricia J., E-mail: patty.nelemans@maastrichtuniversity.nl [Maastricht University Medical Centre, Department of Epidemiology (Netherlands); Wildberger, Joachim E., E-mail: j.wildberger@mumc.nl; Das, Marco, E-mail: m.das@mumc.nl [Maastricht University Medical Center, Department of Radiology (Netherlands)

2015-04-15

PurposeThis study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA).MethodsFusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography.ResultsAverage time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation).ConclusionsFluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety.

Fusion Guidance in Endovascular Peripheral Artery Interventions: A Feasibility Study

International Nuclear Information System (INIS)

Sailer, Anna M.; Haan, Michiel W. de; Graaf, Rick de; Zwam, Willem H. van; Schurink, Geert Willem H.; Nelemans, Patricia J.; Wildberger, Joachim E.; Das, Marco

2015-01-01

PurposeThis study was designed to evaluate the feasibility of endovascular guidance by means of live fluoroscopy fusion with magnetic resonance angiography (MRA) and computed tomography angiography (CTA).MethodsFusion guidance was evaluated in 20 endovascular peripheral artery interventions in 17 patients. Fifteen patients had received preinterventional diagnostic MRA and two patients had undergone CTA. Time for fluoroscopy with MRA/CTA coregistration was recorded. Feasibility of fusion guidance was evaluated according to the following criteria: for every procedure the executing interventional radiologists recorded whether 3D road-mapping provided added value (yes vs. no) and whether PTA and/or stenting could be performed relying on the fusion road-map without need for diagnostic contrast-enhanced angiogram series (CEAS) (yes vs. no). Precision of the fusion road-map was evaluated by recording maximum differences between the position of the vasculature on the virtual CTA/MRA images and conventional angiography.ResultsAverage time needed for image coregistration was 5 ± 2 min. Three-dimensional road-map added value was experienced in 15 procedures in 12 patients. In half of the patients (8/17), intervention was performed relying on the fusion road-map only, without diagnostic CEAS. In two patients, MRA roadmap showed a false-positive lesion. Excluding three patients with inordinate movements, mean difference in position of vasculature on angiography and MRA/CTA road-map was 1.86 ± 0.95 mm, implying that approximately 95 % of differences were between 0 and 3.72 mm (2 ± 1.96 standard deviation).ConclusionsFluoroscopy with MRA/CTA fusion guidance for peripheral artery interventions is feasible. By reducing the number of CEAS, this technology may contribute to enhance procedural safety

What is desirable and feasible in dose reconstruction for application in epidemiological studies?

International Nuclear Information System (INIS)

Bouville, A.; Anspaugh, L.; Beebe, G.W.

1996-01-01

Formal epidemiologic studies are intended to increase scientific knowledge about the quantitative risk that is associated with radiation exposure. Dosimetric data are needed for such studies. What dosimetric data are desirable? Doses are needed for a large number of people with a large gradation of radiation exposures in order to ensure a sufficient power for the epidemiological study. The characteristics of the desirable doses are, in some respects, different from those calculated for radiation protection purposes. The desirable data are: absorbed doses to the individual organs or tissues of interest, instead of effective doses; absorbed doses delivered over limited time periods, instead of committed doses; doses specific to the individuals that are subjects in the epidemiological studies, instead of average doses over population groups; and very accurate and precise doses. What dosimetric data are feasible? Most of the characteristics of the desirable dosimetric data are usually achievable. However, uncertainties can be fairly large and estimated with a large degree of subjectivity. Also, for practical reasons, it may not be feasible to estimate individual doses for all subjects

Phase Two Feasibility Study for Software Safety Requirements Analysis Using Model Checking

Science.gov (United States)

Turgeon, Gregory; Price, Petra

2010-01-01

A feasibility study was performed on a representative aerospace system to determine the following: (1) the benefits and limitations to using SCADE , a commercially available tool for model checking, in comparison to using a proprietary tool that was studied previously [1] and (2) metrics for performing the model checking and for assessing the findings. This study was performed independently of the development task by a group unfamiliar with the system, providing a fresh, external perspective free from development bias.

Feasibility study for the implementation of NRTMA system for an industrial nuclear fuel fabrication plant

International Nuclear Information System (INIS)

Aparo, M.; Dionisi, M.; Graziani, M.; Remetti, R.

1989-01-01

In the frame of the problems arising from the fissile materials safeguards into the facilities of the nuclear fuel cycle, the International Safeguards devoted, in the recent years, R and D efforts on a new Dynamic Accountability procedures (Near Real Time Material Accountancy) appealing to the needs of timeliness in detecting diversion. This paper deals with a feasibility study of a NRTMA system to be applied to a nuclear fuel fabbrication plant for light water reactor. Such a feasibility study was performed by developing a dynamic model and a computer program, written in FORTRAN 77, in order to simulate all the processes and measurement procedures involved in the nuclear material accountancy

Feasibility Study on HYSOL CSP

DEFF Research Database (Denmark)

Nielsen, Lars Henrik; Skytte, Klaus; Pérez, Cristian Hernán Cabrera

2016-01-01

Concentrating Solar Power (CSP) plants utilize thermal conversion of direct solar irradiation. A trough or tower configuration focuses solar radiation and heats up oil or molten salt that subsequently in high temperature heat exchangers generate steam for power generation. High temperature molten...... salt can be stored and the stored heat can thus increase the load factor and the usability for a CSP plant, e.g. to cover evening peak demand. In the HYSOL concept (HYbrid SOLar) such configuration is extended further to include a gas turbine fuelled by upgraded biogas or natural gas. The optimised...... integrated HYSOL concept, therefore, becomes a fully dispatchable (offering firm power) and fully renewable energy source (RES) based power supply alternative, offering CO2-free electricity in regions with sufficient solar resources. The economic feasibility of HYSOL configurations is addressed in this paper...

Feasibility study on floating nuclear power station

International Nuclear Information System (INIS)

Kajima, Ryoichi

1987-01-01

It is stipulated that nuclear power plants are to be built on solid rock bases on land in Japan. However, there are a limited number of appropriate siting grounds. The Central Research Institute of Electric Power Industry has engaged since 1981 in the studies on the construction technology of power plants, aiming at establishing new siting technology to expand the possible siting areas for nuclear power plants. Underground siting is regarded as a proven technology due to the experience in underground hydroelectric power plants. The technology of siting on quaternary ground is now at the stage of verification. In this report, the outline of floating type offshore/inshore siting technology is introduced, which is considered to be feasible in view of the technical and economical aspects. Three fixed structure types were selected, of which the foundations are fixed to seabed, plant superstructures are above sea surface, and which are floating type. Aiming at ensuring the aseismatic stability of the plant foundations, the construction technology is studied, and the structural concept omitting buoyancy is possible. The most practical water depth is not more than 20 m. The overall plant design, earthquake isolation effect and breakwater are described. (Kako, I.)

Feasibility study on Ashuganj NGL Fractionation Plant

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A feasibility study has been performed on Ashuganj NGL Fractionation Plant being planned in the People's Republic of Bangladesh. The present study has discussed a plant to manufacture liquefied oil gas, automotive fuel, and diesel fuel from liquefied natural gas. The plan calls for the plant life of 20 years, liquefied natural gas as the raw material to be supplied continuously and stably from the gas reservoir areas via the existing pipelines, the storage tank to have a size of 10-day production, and the product to be transported by barges on Meghna River. As a result of the discussions, the liquefied oil gas produced annually will correspond to crude oil of 44,690 tons, and to 858,048 tons of crude oil cumulatively for 20 years of the plant life. This is an energy derived from unutilized natural gas, which is creation of a new energy. With regard to the reduction of global warming gas emission, it was revealed that a reduction effect of 16,540,000 t-CO2 can be obtained in twenty years, if comparison is made based on combustion of firewood. (NEDO)

Feasibility study on Ashuganj NGL Fractionation Plant

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A feasibility study has been performed on Ashuganj NGL Fractionation Plant being planned in the People's Republic of Bangladesh. The present study has discussed a plant to manufacture liquefied oil gas, automotive fuel, and diesel fuel from liquefied natural gas. The plan calls for the plant life of 20 years, liquefied natural gas as the raw material to be supplied continuously and stably from the gas reservoir areas via the existing pipelines, the storage tank to have a size of 10-day production, and the product to be transported by barges on Meghna River. As a result of the discussions, the liquefied oil gas produced annually will correspond to crude oil of 44,690 tons, and to 858,048 tons of crude oil cumulatively for 20 years of the plant life. This is an energy derived from unutilized natural gas, which is creation of a new energy. With regard to the reduction of global warming gas emission, it was revealed that a reduction effect of 16,540,000 t-CO2 can be obtained in twenty years, if comparison is made based on combustion of firewood. (NEDO)

Relationship between geohydrology and Upper Pleistocene-Holocene evolution of the eastern region of the Province of Buenos Aires, Argentina

Science.gov (United States)

Capítulo, Leandro Rodrigues; Kruse, Eduardo E.

2017-07-01

The Upper Pleistocene-Holocene geological evolution, which is characterized by its landscape-forming energy and is related to geological and geomorphological complexity, has an impact on the groundwater dynamics of coastal aquifers. The geological configuration of a sector of the east coast of the Province of Buenos Aires was analyzed, as well as its connection with the geological and geomorphological history of the region during the Late Pleistocene and Holocene, and its influence on the regional and local geohydrological behaviour. This analysis was based on the application of the concept of hydrofacies. Boreholes were drilled and sampled (with depths of up to 40 m), and vertical electrical sounding, electrical tomography and pumping tests were undertaken. The description of the cutting samples by means of a stereo microscope, the interpretation of satellite images, and the construction of lithological and hydrogeological profiles and flow charts were carried out in the laboratory, and then integrated in a GIS. The identification of the lithological units and their distribution in the area allowed the construction of an evolutionary geological model for the Late Pleistocene and Holocene. Three aquifer units can be recognized: one of Late Pleistocene age (hydrofacies E) and the other two of Holocene age (hydrofacies A and C); their hydraulic connection depends on the occurrence and thickness variation of the aquitard units (hydrofacies B and D). The approach adopted allows the examination of the possibilities for groundwater exploitation and constitutes an applied conceptual framework to be taken into consideration when developing conceptual and numerical models at the local and regional scales.

Feasibility study. Solar energy in Norway; Mulighetsstudie. Solenergi i Norge

Energy Technology Data Exchange (ETDEWEB)

Halvorsen, Una; Bernhard, Peter; Salvesen, Fritjof; Bugge, Lars; Andresen, Inger; Simonsen, Ingeborg

2011-07-01

On behalf of Enova KanEnergi and SINTEF summarized the results of the project 'Feasibility study. Solar energy' in a report. The purpose of this report is to outline an overview of the potential for solar energy in Norway to be realized until 2020. This is a survey of the status of technology and associated costs related to energy production, as well as a description of the market conditions. This report is a contribution to Enova's ongoing strategy and development. (eb)

A study on the feasibility of minor actinides in BWR

International Nuclear Information System (INIS)

Abdul Waris; Budiono

2008-01-01

Preliminary study on the feasibility of actinides minor (MA) recycling without mixing them with plutonium in boiling water reactor (BWR) has been carried out. The results show that increasing of fissile MA content in mixed oxide fuel (MOX) and/or reducing void fraction can enlarge the effective multiplication factor at the beginning of cycle, but the reactor still can not obtain its criticality condition. Furthermore, dropping the void fraction results in higher reactivity swing and therefore plummeting the safety factor of the reactor. (author)

Feasibility Study of Grid Connected PV-Biomass Integrated Energy System in Egypt

Science.gov (United States)

Barakat, Shimaa; Samy, M. M.; Eteiba, Magdy B.; Wahba, Wael Ismael

2016-10-01

The aim of this paper is to present a feasibility study of a grid connected photovoltaic (PV) and biomass Integrated renewable energy (IRE) system providing electricity to rural areas in the Beni Suef governorate, Egypt. The system load of the village is analyzed through the environmental and economic aspects. The model has been designed to provide an optimal system configuration based on daily data for energy availability and demands. A case study area, Monshaet Taher village (29° 1' 17.0718"N, 30° 52' 17.04"E) is identified for economic feasibility in this paper. HOMER optimization model plan imputed from total daily load demand, 2,340 kWh/day for current energy consuming of 223 households with Annual Average Insolation Incident on a Horizontal Surface of 5.79 (kWh/m2/day) and average biomass supplying 25 tons / day. It is found that a grid connected PV-biomass IRE system is an effective way of emissions reduction and it does not increase the investment of the energy system.

A Pilot Study to Assess the Feasibility of Group Exercise and Animal-Assisted Therapy in Older Adults.

Science.gov (United States)

Grubbs, Brandon; Artese, Ashley; Schmitt, Karla; Cormier, Eileen; Panton, Lynn

2016-04-01

This pilot study assessed the feasibility of incorporating animal-assisted therapy teams (ATT) into a 6-week group exercise program for older adults (77 ± 6 years). Fifteen participants were randomly assigned to an exercise with ATT (E+ATT; n = 8) or exercise only (E; n = 7) group. Groups exercised 3x/week for 45 min. Feasibility was assessed by three objectives: (1) ATT will not need extensive preparation beyond their original therapy training; (2) the study will require minimal cost; and (3) ATT must not impair the effectiveness of the exercise program. By the study conclusion, all objectives were met. Time and cost were minimal for ATT, and adherence was 93% and 90% for E+ATT and E, respectively. There were significant improvements in both groups (p ≤ .05) for arm curls, get-up and go, and 6-min walk. The results of this pilot study suggest that it is feasible to incorporate ATT into group exercise programming for older adults.

Case Study Application of the Biodiversity Security Index to Ranking Feasibility Studies for Ecosystem Restoration Projects of the U.S. Army Corps of Engineers

Science.gov (United States)

2016-04-01

ER D C/ EL C R- 16 -1 Ecosystem Management and Restoration Research Program Case Study Application of the Biodiversity Security Index... Biodiversity Security Index to Ranking Feasibility Studies for Ecosystem Restoration Projects of the U.S. Army Corps of Engineers Richard A. Cole... Biodiversity Security Index (BSI) was applied to 23 project sites ranked for restoration feasibility study annual funding by the U. S. Army Corps of

Medical yoga in the workplace setting-perceived stress and work ability-a feasibility study.

Science.gov (United States)

Axén, Iben; Follin, Gabriella

2017-02-01

This study examined the feasibility of using an intervention of Medical Yoga in the workplace and investigated its effects on perceived stress and work ability. This was a quasi-experimental pilot study comparing a group who received Medical Yoga (intervention group, N=17), with a group waiting to receive Medical Yoga (control group, N=15). Medical Yoga in nine weekly sessions led by a certified instructor, as well as an instruction film to be followed at home twice weekly. Feasibility was assessed through recruitment, eligibility, willingness to participate, response to questionnaires and adherence to the intervention plan. Stress was measured with the Perceived Stress Scale, work ability with the Work Ability Index. Convincing unit managers to let their employees participate in this intervention was difficult. Eligibility was perfect, but only 40% of workers were willing to participate. The subjects adhered to a great extent to the intervention and answered the questionnaires satisfactorily. Reaching target individuals requires careful attention to informing participants. The intervention showed no significant effects on stress and work ability, though the two measures correlated significantly over time. Factors limiting feasibility of this workplace intervention were identified. Work place interventions may need to be sanctioned at a higher managerial level. The optimal time, length and availability of the workplace intervention should be explored further. Knowledge from this study could be used as a foundation when planning a larger scale study. Copyright © 2016 Elsevier Ltd. All rights reserved.

Waste Management Plan for the Oak Ridge National Remedial Investigation/Feasibility Study

International Nuclear Information System (INIS)

1988-04-01

In accordance with the requirements of the Remedial Investigation/Feasibility Study (RI/FS) Project Quality Assurance Plan, this Waste Management Plan establishes clear lines of responsibility and authority, documentation requirements, and operational guidance for the collection, identification, segregation, classification, packaging, certification, and storage/disposal of wastes. These subjects are discussed in the subsequent sections of this document

Summary of some feasibility studies for site-specific solar industrial process heat

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

Some feasibility studies for several different site specific solar industrial process heat applications are summarized. The followng applications are examined. Leather Tanning; Concrete Production: Lumber and Paper Processing; Milk Processing; Molding, Curing or Drying; Automobile Manufacture; and Food Processing and Preparation. For each application, site and process data, system design, and performance and cost estimates are summarized.

Waste Management Plan for the Oak Ridge National Remedial Investigation/Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

1988-04-01

In accordance with the requirements of the Remedial Investigation/Feasibility Study (RI/FS) Project Quality Assurance Plan, this Waste Management Plan establishes clear lines of responsibility and authority, documentation requirements, and operational guidance for the collection, identification, segregation, classification, packaging, certification, and storage/disposal of wastes. These subjects are discussed in the subsequent sections of this document.

A preliminary feasibility study on natural analogue in Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, Chun Soo; Bae, Dae Seok; Kim, Kyung Su; Koh, Yong Kwon; Park, Byung Yun

2000-03-01

Preliminary study on the assessment of natural analogue study in Korea for the deep geological disposal of high-level radioactive waste was carried out. The project on natural analogue study in other countries are introduced. The uranium-bearing deposit in Okcheon belt are summarized, which reported to be uranium-bearing minerals in order to assess to feasibility for natural analogue study in Korea. Among the uranium-bearing deposits, the Deokpyeong area, reported to be the highest reservoir and grade, are selected as the study site, and the elementary investigation, including survey of radioactivity and geochemistry are carried out. According to the investigation of surface environment, the radioactivity and uranium content in the surface water and shallow groundwater does not show any anormal values. However, the radioactivity is expected to be increased in depth and the groundwater reacted with uranium-bearing graphite formation shows high unanium content, indicating the potential possibility for natural analogue study in Korea. In future, if more detail study are performed, the assessment of natural analogue study in Korea are expected.

Feasibility Study of Laser Cutting for Fabrication of Tensile Specimen

International Nuclear Information System (INIS)

Jin, Y. G.; Baik, S. J.; Kim, G. S.; Heo, G. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B.

2015-01-01

The specimen fabrication technique was established to machine the specimen from the irradiated materials. The wire cut EDM(electric discharge machine) was modified to fabricate the mechanical testing specimens from irradiated components and fuel claddings. The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated components and claddings interrupted the applying the electric current during the processing. However, zirconium oxide is protective against further corrosion as well as beneficial to mechanical strength for the tensile deformation of the cladding. Thus, it is important to fabricate the irradiated specimens without removal of oxide layer on the surface of the irradiated structural components and claddings. In the present study, laser cutting system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the feasibility of the laser cutting system was studied for the fabrication of various types of irradiated specimens in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser beam machining system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the dimensions were compared for the feasibility of the laser cutting system. The effect of surface oxide layer was also investigated for machining process of the zircaloy-4 fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer

Feasibility Study of Laser Cutting for Fabrication of Tensile Specimen

Energy Technology Data Exchange (ETDEWEB)

Jin, Y. G.; Baik, S. J.; Kim, G. S.; Heo, G. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The specimen fabrication technique was established to machine the specimen from the irradiated materials. The wire cut EDM(electric discharge machine) was modified to fabricate the mechanical testing specimens from irradiated components and fuel claddings. The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated components and claddings interrupted the applying the electric current during the processing. However, zirconium oxide is protective against further corrosion as well as beneficial to mechanical strength for the tensile deformation of the cladding. Thus, it is important to fabricate the irradiated specimens without removal of oxide layer on the surface of the irradiated structural components and claddings. In the present study, laser cutting system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the feasibility of the laser cutting system was studied for the fabrication of various types of irradiated specimens in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser beam machining system was introduced to fabricate the various mechanical testing specimens from the unirradiated fuel cladding and the dimensions were compared for the feasibility of the laser cutting system. The effect of surface oxide layer was also investigated for machining process of the zircaloy-4 fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer.

Feasibility model study for Blumbangreksa product model based on lean startup method

Science.gov (United States)

Pakpahan, A. K.; Dewobroto, W. S.; Pratama, R. Y.

2017-12-01

Based on the data from Ministry of Maritime Affairs and Fisheries in 2015, the productivity of shrimp farmers in Indonesia is still below China, India and Thailand, because of the low survival rate of shrimp seeds were planted in Indonesia. Water quality factors become a significant factor that increasesthe survival rate of shrimp seeds plantation, therefore team of PT. Atnic EkoteknoWicaksana create a tool called Blumbangreksa that able to monitor water quality of shrimp farms, measure temperature, salinity, pH, DO (dissolved oxygen), TDS (total dissolve solid) in water and moist air over the surface of the water and GSM -based and Internet of things. Based on the research results, unique value proposition of Blumbangreksa products is the measurement result of water quality are accurate, real-time measurements, based on Internet of things and have the ability measurements at once. Based on the feasibility study using the opportunity assessment of Marty Cagan, it can be seen that the product has fulfilled ten elements of assessment opportunity, so Blumbangreksa products are considered feasible. Initial investment fund of Blumbangreksa products is Rp 1,369,856,574, with profitability index of 1:51 and average breakeven products each year as many as 18 products are sold, and the payback period for 4 years and 2 months, therefore the business of Blumbangreksa product is feasible.

Feasibility study of a lens-coupled charge-coupled device gamma camera

International Nuclear Information System (INIS)

Lee, Hakjae; Jung, Youngjun; Kim, Jungmin; Bae, Seungbin; Lee, Kisung; Kang, Jungwon

2011-01-01

A charge-coupled device (CCD) is generally used in a digital camera as a light-collecting device such as a photomultiplier tube (PMT). Because of its low sensitivity and very high dark current, CCD have not been popularly used for gamma imaging systems. However, a recent CCD technological breakthrough has improved CCD sensitivity, and the use of a Peltier cooling system can significantly minimize the dark current. In this study, we investigated the feasibility of a prototype CCD gamma camera consisting of a CsI scintillator, optical lenses, and a CCD module. Despite electron-multiplying (EM) CCDs having higher performance, in this study, we built a cost-effective system consisted of low-cost components compared to EMCCDs. Our prototype detector consists of a CsI scintillator, two optical lenses, and a conventional Peltier-cooled CCD. The performance of this detector was evaluated by acquiring the sensitivity, resolution, and the modulation transfer function (MTF). The sensitivity of the prototype detector showed excellent linearity. With a 1 mm-diameter pinhole collimator, the full width at half-maximum (FWHM) of a 1.1 mm Tc-99m line source image was 2.85 mm. These results show that the developed prototype camera is feasible for small animal gamma imaging.

Differentiating pheochromocytoma from lipid-poor adrenocortical adenoma by CT texture analysis: feasibility study.

Science.gov (United States)

Zhang, Gu-Mu-Yang; Shi, Bing; Sun, Hao; Jin, Zheng-Yu; Xue, Hua-Dan

2017-09-01

To investigate the feasibility of using CT texture analysis (CTTA) to differentiate pheochromocytoma from lipid-poor adrenocortical adenoma (lp-ACA). Ninety-eight pheochromocytomas and 66 lp-ACAs were included in this retrospective study. CTTA was performed on unenhanced and enhanced images. Receiver operating characteristic (ROC) analysis was performed, and the area under the ROC curve (AUC) was calculated for texture parameters that were significantly different for the objective. Diagnostic accuracies were evaluated using the cutoff values of texture parameters with the highest AUCs. Compared to lp-ACAs, pheochromocytomas had significantly higher mean gray-level intensity (Mean), entropy, and mean of positive pixels (MPP), but lower skewness and kurtosis on unenhanced images (P feasible to use CTTA to differentiate pheochromocytoma from lp-ACA.

Assessing the feasibility of the Healthy Life in Suriname Study: using advanced hemodynamics to evaluate cardiovascular risk

Directory of Open Access Journals (Sweden)

Jet Q. Aartman

2017-06-01

Full Text Available ABSTRACT Objectives To determine the feasibility of assessing population cardiovascular risk with advanced hemodynamics in the Healthy Life in Suriname (HELISUR study. Methods This was a preliminary study conducted in May – June 2012 using the Technical-Economic-Legal-Operational-Scheduling (TELOS method to assess the feasibility of the HELISUR—a large-scale, cross-sectional population study of cardiovascular risk factors and disease in Suriname. Suriname, a middle-income country in South America with a population of mostly African and Asian ethnicity, has a high risk of cardiovascular disease. A total of 135 volunteers 18 – 70 years of age participated. A health questionnaire was tested in a primary health care center, and non-invasive cardiovascular evaluations were performed in an academic health center. The cardiovascular evaluation included sitting, supine, and standing blood pressure, and intermediate endpoints, such as cardiac output, peripheral vascular resistance, pulse wave velocity, and augmentation index. Results The TELOS testing found that communicating by cellular phone was most effective for appointment adherence, and that completion of the questionnaire often required assistance from a trained interviewer; modifications to improve the clarity of the questions are recommended. Regarding the extended cardiovascular assessments of peripheral and central hemodynamics, the findings showed these to be technically and operationally feasible and well tolerated by participants, in terms of burden and duration. Conclusions Findings of this feasibility assessment indicate that large-scale, detailed evaluations of cardiovascular risk, including a questionnaire and advanced central and peripheral hemodynamics, are feasible in a high-risk population in a middle-income setting.

Visualization of bonding at an inclusion boundary using axial-shear strain elastography: a feasibility study

International Nuclear Information System (INIS)

Thitaikumar, Arun; Krouskop, Thomas A; Garra, Brian S; Ophir, Jonathan

2007-01-01

Ultrasound elastography produces strain images of compliant tissues under quasi-static compression. In axial-shear strain elastography, the local axial-shear strain resulting from application of quasi-static axial compression to an inhomogeneous material is imaged. The overall hypothesis of this work is that the pattern of axial-shear strain distribution around the inclusion/background interface is completely determined by the bonding at the interface after normalization for inclusion size and applied strain levels, and that it is feasible to extract certain features from the axial-shear strain elastograms to quantify this pattern. The mechanical model used in this study consisted of a single stiff circular inclusion embedded in a homogeneous softer background. First, we performed a parametric study using finite-element analysis (FEA) (no ultrasound involved) to identify possible features that quantify the pattern of axial-shear strain distribution around an inclusion/background interface. Next, the ability to extract these features from axial-shear strain elastograms, estimated from simulated pre- and post-compression noisy RF data, was investigated. Further, the feasibility of extracting these features from in vivo breast data of benign and malignant tumors was also investigated. It is shown using the FEA study that the pattern of axial-shear strain distribution is determined by the degree of bonding at the inclusion/background interface. The results suggest the feasibility of using normalized features that capture the region of positive and negative axial-shear strain area to quantify the pattern of the axial-shear strain distribution. The simulation results showed that it was feasible to extract the features, as identified in the FEA study, from axial-shear strain elastograms. However, an effort must be made to obtain axial-shear strain elastograms with the highest signal-to-noise ratio (SNR asse ) possible, without compromising the resolution. The in vivo

IRT - Sofia conversion feasibility study experience 2002-2009

Energy Technology Data Exchange (ETDEWEB)

Belousov, S.I.; Apostolov, T.G. [Institute for Nuclear Research and Nuclear Energy of Bulgarian Academy of Science, Tsarigradsko 72, 1784 Sofia (Bulgaria)

2010-07-01

A joint conversion feasibility study concerning the IRT - Sofia research reactor between INRNE and the RERTR Program at ANL was initiated in 2002. The initial steps studies (up to 2006) were mainly focused on neutronics properties significant for reactor application and safety analyses. Thermal hydraulic, accident analyses as well as additional neutronics study required were performed after that (up to 2010). The obtained results show that the IRT-4M LEU fuel assemblies (19.75% {sup 235}U enrichment) are appropriate for IRT-Sofia conversion (IRT-Sofia was initially designed for the IRT-2M HEU fuel assemblies with 36% {sup 235}U enrichment). The results obtained in the frames of the joint study show that the IRT-Sofia operation even with usage of only one pump in the primary circuit meets all safety requirements at power level up to 1000 kW and that safety is maintained for accident transients. Presented results of analyses (neutronics, thermal hydraulic, and accident) and accumulated experience for the IRT-Sofia will be useful for other research reactors where conversion from IRT-2M (HEU) to IRT-4M (LEU) fuel is underway and/or foreseen. (authors)

Measures and Metrics for Feasibility of Proof-of-Concept Studies With Human Immunodeficiency Virus Rapid Point-of-Care Technologies

Science.gov (United States)

Pant Pai, Nitika; Chiavegatti, Tiago; Vijh, Rohit; Karatzas, Nicolaos; Daher, Jana; Smallwood, Megan; Wong, Tom; Engel, Nora

2017-01-01

Objective Pilot (feasibility) studies form a vast majority of diagnostic studies with point-of-care technologies but often lack use of clear measures/metrics and a consistent framework for reporting and evaluation. To fill this gap, we systematically reviewed data to (a) catalog feasibility measures/metrics and (b) propose a framework. Methods For the period January 2000 to March 2014, 2 reviewers searched 4 databases (MEDLINE, EMBASE, CINAHL, Scopus), retrieved 1441 citations, and abstracted data from 81 studies. We observed 2 major categories of measures, that is, implementation centered and patient centered, and 4 subcategories of measures, that is, feasibility, acceptability, preference, and patient experience. We defined and delineated metrics and measures for a feasibility framework. We documented impact measures for a comparison. Findings We observed heterogeneity in reporting of metrics as well as misclassification and misuse of metrics within measures. Although we observed poorly defined measures and metrics for feasibility, preference, and patient experience, in contrast, acceptability measure was the best defined. For example, within feasibility, metrics such as consent, completion, new infection, linkage rates, and turnaround times were misclassified and reported. Similarly, patient experience was variously reported as test convenience, comfort, pain, and/or satisfaction. In contrast, within impact measures, all the metrics were well documented, thus serving as a good baseline comparator. With our framework, we classified, delineated, and defined quantitative measures and metrics for feasibility. Conclusions Our framework, with its defined measures/metrics, could reduce misclassification and improve the overall quality of reporting for monitoring and evaluation of rapid point-of-care technology strategies and their context-driven optimization. PMID:29333105

Internal voltage control of hydrogen-oxygen fuel cells: Feasibility study

Science.gov (United States)

Prokopius, P. R.

1975-01-01

An experimental study was conducted to assess the feasibility of internal voltage regulation of fuel cell systems. Two methods were tested. In one, reactant partial pressure was used as the voltage control parameter and in the other reactant total pressure was used for control. Both techniques were breadboarded and tested on a single alkaline-electrolyte fuel cell. Both methods were found to be possible forms of regulation, however, of the two the total pressure technique would be more efficient, simpler to apply and would provide better transient characteristics.

Char-recirculation biomass gasification system--a site-specific feasibility study

International Nuclear Information System (INIS)

Purdy, K.R.; Kerr, C.P.; Hensley, B.D.

1991-01-01

A site-specific feasibility study was conducted for a char-recirculation biomass gasification plant which would dispose of the chippable solid residues of the area sawmills. The plant would receive green hardwood chips and convert them into active charcoal while producing process steam and electrical power. An economic analysis was performed on the basis of not-for-profit operation, marketing crushed active charcoal to a broker at a discounted price, and displacing purchased electric power. Given a market for the active charcoal, the plant was judged to be economically viable

Technological feasibility studies on combination treatments for subtropical fruits

International Nuclear Information System (INIS)

Brodrick, H.T.; Linde, H.J. van der

1981-01-01

Research with subtropical fruits such as papayas and mangoes had advanced beyond the experimental stage in South Africa. This may be attributed to the potential economic benefits likely to be obtained from the combination of heat and irradiation treatments. The outcome of recent marketing trials, however, revealed several problem areas which need further investigation. Some of these problems were studied in greater detail and are reported in this presentation. The effect of time delays between hot-water and irradiation treatments on the efficacy in disease control in the fruit, has received particular attention in the investigations. Efforts have also been made to correlate these results with those obtained in fungal studies in the laboratory. These and other factors relating to the technological feasibility in the use of combined treatments for the preservation of mangoes and papayas are discussed and recommendations or guidelines for future studies are given in this paper. (author)

Feasibility Study of Parallel Finite Element Analysis on Cluster-of-Clusters

Science.gov (United States)

Muraoka, Masae; Okuda, Hiroshi

With the rapid growth of WAN infrastructure and development of Grid middleware, it's become a realistic and attractive methodology to connect cluster machines on wide-area network for the execution of computation-demanding applications. Many existing parallel finite element (FE) applications have been, however, designed and developed with a single computing resource in mind, since such applications require frequent synchronization and communication among processes. There have been few FE applications that can exploit the distributed environment so far. In this study, we explore the feasibility of FE applications on the cluster-of-clusters. First, we classify FE applications into two types, tightly coupled applications (TCA) and loosely coupled applications (LCA) based on their communication pattern. A prototype of each application is implemented on the cluster-of-clusters. We perform numerical experiments executing TCA and LCA on both the cluster-of-clusters and a single cluster. Thorough these experiments, by comparing the performances and communication cost in each case, we evaluate the feasibility of FEA on the cluster-of-clusters.

Pneumatic artificial muscles for trailing edge flap actuation: a feasibility study

International Nuclear Information System (INIS)

Woods, Benjamin K S; Wereley, Norman M; Kothera, Curt S; Sirohi, Jayant

2011-01-01

In this study a novel aircraft trailing edge flap actuation system was developed and tested. Pneumatic artificial muscles (PAMs) were used as the driving elements of this system to demonstrate their feasibility and utility as an alternative aerospace actuation technology. A prototype flap/actuator system was integrated into a model wing section and tested on the bench-top under simulated airloads for flight at 100 m s −1 (M = 0.3) and in an open-jet wind tunnel at free stream velocities ranging up to 45 m s −1 (M = 0.13). Testing was performed for actuator pressures ranging from 0.069 to 0.62 MPa (10–90 psi) and actuation frequencies from 0.1 to 31 Hz. Results show that the PAM-driven trailing edge flap system can generate substantial and sustainable dynamic deflections, thereby proving the feasibility of using pneumatic artificial muscle actuators in a trailing edge flap system. Key issues limiting system performance are identified, that should be resolved in future research

"Merging Yoga and Occupational Therapy (MY-OT): A feasibility and pilot study".

Science.gov (United States)

Schmid, Arlene A; Puymbroeck, Marieke Van; Portz, Jennifer D; Atler, Karen E; Fruhauf, Christine A

2016-10-01

To examine the feasibility and benefits of the Merging Yoga and Occupational Therapy (MY-OT) intervention. This is the primary analysis of a non-controlled pretest-posttest pilot study to understand the feasibility and impact of MY-OT on balance, balance self-efficacy, and fall risk factor management in people with chronic stroke. University research laboratory. People with chronic stroke were included in the study if they: had sustained a fall or had fear of falling, were able to stand, and hand impaired balance and were at risk for falls (≤46 on the Berg Balance Scale (BBS)). Individuals completed an 8 week intervention that included 16 sessions of both yoga and group occupational therapy (OT). Yoga included physical postures, breathing exercises, and meditation. OT focused on post-stroke fall risk factor management. The BBS was used to assess balance, the Activities-specific Balance Confidence Scale (ABC) was used to measure balance self-efficacy. Five fall risk factor management scales were used. Overall, the intervention was considered feasible, as individuals were able to safely complete the intervention with little attrition and high attendance. Balance improved by 30% (p=0.002). Balance self-efficacy improved by 15% (p=0.034). Each of the five fall risk factor management scales improved, but only two significantly improved (Fall Prevention and Management Questionnaire, 29%, p=0.004 and Fall Prevention Strategy Survey, 42%, p=0.032). The results demonstrate that MY-OT is a potential intervention to improve multiple fall related outcomes for people with stroke. Therapists may consider these interventions for people with stroke, but additional research is warranted. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pharmacokinetically guided sunitinib dosing: a feasibility study in patients with advanced solid tumours

NARCIS (Netherlands)

Lankheet, N.; Kloth, J.S.; Gadellaa-van Hooijdonk, C.G.M.; Cirkel, G.A.; Mathijssen, R.H.; Lolkema, M.P.; Schellens, J.H.; Voest, E.E.; Sleijfer, S.; Jonge, M.J. de; Haanen, J.B.; Beijnen, J.H.; Huitema, A.D.; Steeghs, N.

2014-01-01

Background:Plasma exposure of sunitinib shows large inter-individual variation. Therefore, a pharmacokinetic (PK) study was performed to determine safety and feasibility of sunitinib dosing based on PK levels.Methods:Patients were treated with sunitinib 37.5 mg once daily. At days 15 and 29 of

Therapeutic drug monitoring to individualize the dosing of pazopanib: a pharmacokinetic feasibility study

NARCIS (Netherlands)

Wit, D. de; Erp, N. van; Hartigh, J. den; Wolterbeek, R..; Hollander-van Deursen, M. den; Labots, M.; Guchelaar (LUMC), H.J.; Verheul, H.M.; Gelderblom, H.

2015-01-01

BACKGROUND: Patients treated with the standard dose of pazopanib show a large interpatient variability in drug exposure defined as the area under the plasma concentration-time curve (AUC0-24h). The primary objective of this study was to evaluate the feasibility of pharmacokinetics (PK)-guided

Planning study and economic feasibility for extended life operation of light water reactor plants

International Nuclear Information System (INIS)

Negin, C.A.; Goudarzi, L.A.; Kenworthy, L.U.; Lapides, M.E.

1980-01-01

The purpose of this planning study was to perform an assessment of the engineering and economic feasibility of extended life operation of present nuclear power plant units and to recommend future programs that may be warranted by the feasibility assessments. This effort concludes, essentially, that there is sufficient economic motivation for refurbishment to warrant more extensive examination for present plants and to identify possible design modifications that would facilitate extended service life in future plants. The costs of replacing the deterioration-prone equipment in a nuclear power plant appear to represent a small portion of the total plant costs, provided downtime is not excessive. A refurbishment and economic analysis is presented

[The relevance of core muscles in ice hockey players: a feasibility study].

Science.gov (United States)

Rogan, S; Blasimann, A; Nyffenegger, D; Zimmerli, N; Radlinger, L

2013-12-01

Good core strength is seen as a condition for high performance in sports. In general, especially maximum voluntary contraction (MVC) and strength endurance (SE) measurements of the core muscles are used. In addition, a few studies can be found that examine the core muscles in terms of MVC, rate of force development (RFD) and SE. Primary aims of this feasibility study were to investigate the feasibility regarding recruiting process, compliance and safety of the testing conditions and raise the force capabilities MVC, RFD and SE of the core muscles in amateur ice hockey players. Secondarily, tendencies of correlations between muscle activity and either shot speed and sprint time shall be examined. In this feasibility study the recruitment process has been approved by 29 ice hockey players, their adherence to the study measurements of trunk muscles, and safety of the measurements was evaluated. To determine the MVC, RFD and SE for the ventral, lateral and dorsal core muscles a dynamic force measurement was performed. To determine the correlation between core muscles and shot speed and 40-m sprint, respectively, the rank correlation coefficient (rho) from Spearman was used. The recruited number of eight field players and one goal-keeper was not very high. The compliance with 100 % was excellent. The players reported no adverse symptoms or injuries after the measurements. The results show median values for the ventral core muscles for MVC with 46.5 kg for RFD with 2.23 m/s2 and 96 s for the SE. For lateral core muscle median values of the lateral core muscles for MVC with 71.10 kg, RFD with 2.59 m/s2 and for SE over 66 s were determined. The dorsal core muscles shows values for MVC 69.7 kg, for RFD 3.39 m/s2 and for SE of 75 s. High correlations between MVC of the ventral core muscles (rho = -0.721, p = 0.021), and between the SE of the ventral core muscles (rho = 0.787, p = 0.012), and the shot velocity rate were determined. Another

Feasibility of generating quantitative composition images in dual energy mammography: a simulation study

Science.gov (United States)

Lee, Donghoon; Kim, Ye-seul; Choi, Sunghoon; Lee, Haenghwa; Choi, Seungyeon; Kim, Hee-Joung

2016-03-01

Breast cancer is one of the most common malignancies in women. For years, mammography has been used as the gold standard for localizing breast cancer, despite its limitation in determining cancer composition. Therefore, the purpose of this simulation study is to confirm the feasibility of obtaining tumor composition using dual energy digital mammography. To generate X-ray sources for dual energy mammography, 26 kVp and 39 kVp voltages were generated for low and high energy beams, respectively. Additionally, the energy subtraction and inverse mapping functions were applied to provide compositional images. The resultant images showed that the breast composition obtained by the inverse mapping function with cubic fitting achieved the highest accuracy and least noise. Furthermore, breast density analysis with cubic fitting showed less than 10% error compare to true values. In conclusion, this study demonstrated the feasibility of creating individual compositional images and capability of analyzing breast density effectively.

Feasibility study of a hybrid wind turbine system – Integration with compressed air energy storage

International Nuclear Information System (INIS)

Sun, Hao; Luo, Xing; Wang, Jihong

2015-01-01

Highlights: • A new hybrid wind turbine system is proposed and feasibility study if conducted. • A complete mathematical model is developed and implemented in a software environment. • Multi-mode control strategy is investigated to ensure the system work smoothly and efficiently. • A prototype for implementing the proposed mechanism is built and tested as proof of the concept. • The proposed system is proved to be technically feasible with energy efficiency around 50%. - Abstract: Wind has been recognized as one of major realistic clean energy sources for power generation to meet the continuously increased energy demand and to achieve the carbon emission reduction targets. However, the utilisation of wind energy encounters an inevitable challenge resulting from the nature of wind intermittency. To address this, the paper presents the recent research work at Warwick on the feasibility study of a new hybrid system by integrating a wind turbine with compressed air energy storage. A mechanical transmission mechanism is designed and implemented for power integration within the hybrid system. A scroll expander is adopted to serve as an “air-machinery energy converter”, which can transmit additional driving power generalized from the stored compressed air to the turbine shaft for smoothing the wind power fluctuation. A mathematical model for the complete hybrid process is developed and the control strategy is investigated for corresponding cooperative operations. A prototype test rig for implementing the proposed mechanism is built for proof of the concept. From the simulated and experimental studies, the energy conversion efficiency analysis is conducted while the system experiences different operation conditions and modes. It is proved that the proposed hybrid wind turbine system is feasible technically

Treatment of nulliparous women with severe fear of childbirth via the Internet: a feasibility study.

Science.gov (United States)

Nieminen, Katri; Andersson, Gerhard; Wijma, Barbro; Ryding, Elsa-Lena; Wijma, Klaas

2016-01-01

The aim of the present study was to test the feasibility of Internet interventions among nulliparous women suffering from severe fear of childbirth (FOC) by means of an Internet-delivered therapist-supported self-help program based on cognitive behavioral therapy (ICBT). Prospective, longitudinal cohort study. A feasibility study of an ICBT program for the treatment of severe FOC in pregnant women. Twenty-eight Swedish-speaking nulliparous women with severe FOC recruited via a project home page from January 2012 to December 2013. The main components of the ICBT program for the treatment of severe FOC comprised psycho-education, breathing retraining, cognitive restructuring, imaginary exposure, in vivo exposure and relapse prevention. The study participants were anonymously self-recruited over the Internet, interviewed by telephone and then enrolled. All participants were offered 8 weeks of treatment via the Internet. Participants reported their homework weekly, submitted measurements of their fear and received feedback from a therapist via a secure online contact management system. Level of FOC measured with the Wijma Delivery Expectancy/Experience Questionnaire (W-DEQ A) during screening at enrollment and weekly during the treatment (W-DEQ version A), and after the delivery (W-DEQ version B). A statistically significant (p pre to post-therapy, with a large effect size (Cohen's d = 0.95)]. The results of this feasibility study suggest that ICBT has potential in the treatment of severe FOC during pregnancy in motivated nulliparous women. The results need to be confirmed by randomized controlled studies.

Feasibility Study for the Use of Green, Bio-Based, Efficient Reactive Sorbent Material to Neutralize Chemical Warfare Agents

Science.gov (United States)

2012-08-02

REPORT Feasibility study for the use of green, bio-based, efficient reactive sorbent material to neutralize chemical warfare agents 14. ABSTRACT 16...way cellulose, lignin and hemicelluloses interact as well as whole wood dissolution occurs in ILs. The present project was conducted to 1. REPORT...Feasibility study for the use of green, bio-based, efficient reactive sorbent material to neutralize chemical warfare agents Report Title ABSTRACT Over the

Feasibility study of plutonium recycling in light water reactors

International Nuclear Information System (INIS)

Tabuchi, Hideoto

1979-01-01

The feasibility of plutonium recycling in light water reactors has been studied by the Agency of Natural Resources and Energy, MITI. As the first step of the feasibility study, it was planned to charge two fuel assemblies, containing uranium-plutonium mixed oxide (MO 2 ), in the core of the Tsuruga nuclear power plant (BWR) for testing. The design of fuel the safety of these fuel and the operating characteristics of these special fuel assemblies were evaluated. The specifications of MO 2 fuel pin and fuel assembly are compared to those of present uranium oxide (UO 2 ) fuel. The weight of fissile plutonium in one MO 2 fuel assembly is 2.22 kg. The characteristics of MO 2 fuel assemblies, such as reactivity, control rod worth and power distribution can be kept similar to UO 2 fuel. The plutonium isotope ratio of the MO 2 fuel is assumed as that obtained in the fuel taken out of the Tokai No. 1 gas cooled reactor. The temperature distribution in the fuel pellets is shown, compared to that of UO 2 fuel. The linear power density is 440 w/cm at the beginning of the fuel life and 360 w/cm after the burn-up of 44,000 Mwd/t. The stress in the cladding tubes of MO 2 fuel is not different from that of UO 2 fuel. The pellet-cladding interaction (PCM1) was analyzed, utilizing the FEM code, FEAST. Concerning the calculation of resonance absorption, the space dependence of thermal neutron spectra and the nuclear behavior of hollow pellets the methods of design calculation were checked up. It was recognized that regarding the nuclear characteristics of MO 2 fuel, no special technical question remains. (Nakai, Y.)

Using the Habit App for Weight Loss Problem Solving: Development and Feasibility Study.

Science.gov (United States)

Pagoto, Sherry; Tulu, Bengisu; Agu, Emmanuel; Waring, Molly E; Oleski, Jessica L; Jake-Schoffman, Danielle E

2018-06-20

Reviews of weight loss mobile apps have revealed they include very few evidence-based features, relying mostly on self-monitoring. Unfortunately, adherence to self-monitoring is often low, especially among patients with motivational challenges. One behavioral strategy that is leveraged in virtually every visit of behavioral weight loss interventions and is specifically used to deal with adherence and motivational issues is problem solving. Problem solving has been successfully implemented in depression mobile apps, but not yet in weight loss apps. This study describes the development and feasibility testing of the Habit app, which was designed to automate problem-solving therapy for weight loss. Two iterative single-arm pilot studies were conducted to evaluate the feasibility and acceptability of the Habit app. In each pilot study, adults who were overweight or obese were enrolled in an 8-week intervention that included the Habit app plus support via a private Facebook group. Feasibility outcomes included retention, app usage, usability, and acceptability. Changes in problem-solving skills and weight over 8 weeks are described, as well as app usage and weight change at 16 weeks. Results from both pilots show acceptable use of the Habit app over 8 weeks with on average two to three uses per week, the recommended rate of use. Acceptability ratings were mixed such that 54% (13/24) and 73% (11/15) of participants found the diet solutions helpful and 71% (17/24) and 80% (12/15) found setting reminders for habits helpful in pilots 1 and 2, respectively. In both pilots, participants lost significant weight (P=.005 and P=.03, respectively). In neither pilot was an effect on problem-solving skills observed (P=.62 and P=.27, respectively). Problem-solving therapy for weight loss is feasible to implement in a mobile app environment; however, automated delivery may not impact problem-solving skills as has been observed previously via human delivery. ClinicalTrials.gov NCT

Electronic Adherence Monitoring in a High-Utilizing Pediatric Asthma Cohort: A Feasibility Study.

Science.gov (United States)

Kenyon, Chén Collin; Chang, Joyce; Wynter, Sheri-Ann; Fowler, Jessica C; Long, Jin; Bryant-Stephens, Tyra C

2016-06-22

Inner-city, minority children with asthma have the highest rates of morbidity and death from asthma and the lowest rates of asthma controller medication adherence. Some recent electronic medication monitoring interventions demonstrated dramatic improvements in adherence in lower-risk populations. The feasibility and acceptability of such an intervention in the highest-risk children with asthma has not been studied. Our objective was to assess the feasibility and acceptability of a community health worker-delivered electronic adherence monitoring intervention among the highest utilizers of acute asthma care in an inner-city practice. This was a prospective cohort pilot study targeting children with the highest frequency of asthma-related emergency department and hospital care within a local managed care Medicaid plan. The 3-month intervention included motivational interviewing, electronic monitoring of controller and rescue inhaler use, and outreach by a community health worker for predefined medication alerts. We measured acceptability by using a modified technology acceptability model and changes in asthma control using the Asthma Control Test (ACT). Given prominent feasibility issues, we describe qualitative patterns of medication use at baseline only. We enrolled 14 non-Hispanic black children with a median age of 3.5 years. Participants averaged 7.8 emergency or hospital visits in the year preceding enrollment. We observed three distinct patterns of baseline controller use: 4 patients demonstrated sustained use, 5 patients had periodic use, and 5 patients lapsed within 2 weeks. All participants initiated use of the electronic devices; however, no modem signal was transmitted for 5 or the 14 participants after a mean of 45 days. Of the 9 (64% of total) caregivers who completed the final study visit, all viewed the electronic monitoring device favorably and would recommend it to friends, and 5 (56%) believed that the device helped to improve asthma control. ACT

Dynamic electron arc radiotherapy (DEAR): a feasibility study

International Nuclear Information System (INIS)

Rodrigues, Anna; Yin, Fang-Fang; Wu, Qiuwen

2014-01-01

Compared to other radiation therapy modalities, clinical electron beam therapy has remained practically unchanged for the past few decades even though electron beams with multiple energies are widely available on most linacs. In this paper, we present the concept of dynamic electron arc radiotherapy (DEAR), a new conformal electron therapy technique with synchronized couch motion. DEAR utilizes combination of gantry rotation, couch motion, and dose rate modulation to achieve desirable dose distributions in patient. The electron applicator is kept to minimize scatter and maintain narrow penumbra. The couch motion is synchronized with the gantry rotation to avoid collision between patient and the electron cone. In this study, we investigate the feasibility of DEAR delivery and demonstrate the potential of DEAR to improve dose distributions on simple cylindrical phantoms. DEAR was delivered on Varian's TrueBeam linac in Research Mode. In conjunction with the recorded trajectory log files, mechanical motion accuracies and dose rate modulation precision were analyzed. Experimental and calculated dose distributions were investigated for different energies (6 and 9 MeV) and cut-out sizes (1×10 cm 2  and 3×10 cm 2  for a 15×15 cm 2  applicator). Our findings show that DEAR delivery is feasible and has the potential to deliver radiation dose with high accuracy (root mean square error, or RMSE of <0.1 MU, <0.1° gantry, and <0.1 cm couch positions) and good dose rate precision (1.6 MU min −1 ). Dose homogeneity within ±2% in large and curved targets can be achieved while maintaining penumbra comparable to a standard electron beam on a flat surface. Further, DEAR does not require fabrication of patient-specific shields. These benefits make DEAR a promising technique for conformal radiotherapy of superficial tumors. (paper)

A Feasibility Study for Mobile Marketing and Distribution Occupational Laboratories in North Dakota.

Science.gov (United States)

Kohns, Donald P.

A study determined the feasibility of a mobile laboratory for marketing and distribution in North Dakota. It attempted to answer four questions: (1) What types of staffing, equipment, curriculum, and delivery systems are presently being utilized in mobile laboratories throughout the nation? (2) What significant information obtained from mobile…

Feasibility study for a muon detector for the CBM experiment

International Nuclear Information System (INIS)

Dutta, Dipanwita; Lebedev, Andrey; Kiseleva, Anna; Ryzhinskiy, Mikhail; Kryshen, Evgeny

2009-01-01

The Compressed Baryonic Matter (CBM) experiment at the future FAIR accelerator facility at GSI, Darmstadt is being designed to investigate heavy ion collisions in fixed target mode at beam energies from 10 - 45 A GeV. The major goal is to explore the QCD phase diagram in the region of high baryon densities and at moderate temperatures. One of the proposed key observables is the measurement of charmonium via the dilepton decay channel. As leptons leave the initially produced hot and dense fireball without further interactions, they are excellent probes to study in-medium properties of vector mesons. In this contribution we will present detailed feasibility studies for a di-muon measurement in CBM

Fuel assembly assessment from CVD image analysis: A feasibility study

International Nuclear Information System (INIS)

Lindsay, C.S.; Lindblad, T.

1997-05-01

The Swedish Nuclear Inspectorate commissioned a feasibility study of automatic assessment of fuel assemblies from images obtained with the digital Cerenkov viewing device currently in development. The goal is to assist the IAEA inspectors in evaluating the fuel since they typically have only a few seconds to inspect an assembly. We report results here in two main areas: Investigation of basic image processing and recognition techniques needed to enhance the images and find the assembly in the image; Study of the properties of the distributions of light from the assemblies to determine whether they provide unique signatures for different burn-up and cooling times for real fuel or indicate presence of non-fuel. 8 refs, 27 figs

Feasibility Study of Solar Photovoltaics on Landfills in Puerto Rico (Second Study)

Energy Technology Data Exchange (ETDEWEB)

Salasovich, J.; Mosey, G.

2011-08-01

This report presents the results of an assessment of the technical and economic feasibility of deploying a solar photovoltaics (PV) system on landfill sites in Puerto Rico. The purpose of this report is to assess the landfills with the highest potential for possible solar PV installation and estimate cost, performance, and site impacts of three different PV options: crystalline silicon (fixed tilt), crystalline silicon (single-axis tracking), and thin film (fixed tilt). The report outlines financing options that could assist in the implementation of a system. According to the site production calculations, the most cost-effective system in terms of return on investment is the thin-film fixed-tilt technology. The report recommends financing options that could assist in the implementation of such a system. The landfills and sites considered in this report were all determined feasible areas in which to implement solar PV systems.

Mobile, real-time, and point-of-care augmented reality is robust, accurate, and feasible: a prospective pilot study.

Science.gov (United States)

Kenngott, Hannes Götz; Preukschas, Anas Amin; Wagner, Martin; Nickel, Felix; Müller, Michael; Bellemann, Nadine; Stock, Christian; Fangerau, Markus; Radeleff, Boris; Kauczor, Hans-Ulrich; Meinzer, Hans-Peter; Maier-Hein, Lena; Müller-Stich, Beat Peter

2018-06-01

Augmented reality (AR) systems are currently being explored by a broad spectrum of industries, mainly for improving point-of-care access to data and images. Especially in surgery and especially for timely decisions in emergency cases, a fast and comprehensive access to images at the patient bedside is mandatory. Currently, imaging data are accessed at a distance from the patient both in time and space, i.e., at a specific workstation. Mobile technology and 3-dimensional (3D) visualization of radiological imaging data promise to overcome these restrictions by making bedside AR feasible. In this project, AR was realized in a surgical setting by fusing a 3D-representation of structures of interest with live camera images on a tablet computer using marker-based registration. The intent of this study was to focus on a thorough evaluation of AR. Feasibility, robustness, and accuracy were thus evaluated consecutively in a phantom model and a porcine model. Additionally feasibility was evaluated in one male volunteer. In the phantom model (n = 10), AR visualization was feasible in 84% of the visualization space with high accuracy (mean reprojection error ± standard deviation (SD): 2.8 ± 2.7 mm; 95th percentile = 6.7 mm). In a porcine model (n = 5), AR visualization was feasible in 79% with high accuracy (mean reprojection error ± SD: 3.5 ± 3.0 mm; 95th percentile = 9.5 mm). Furthermore, AR was successfully used and proved feasible within a male volunteer. Mobile, real-time, and point-of-care AR for clinical purposes proved feasible, robust, and accurate in the phantom, animal, and single-trial human model shown in this study. Consequently, AR following similar implementation proved robust and accurate enough to be evaluated in clinical trials assessing accuracy, robustness in clinical reality, as well as integration into the clinical workflow. If these further studies prove successful, AR might revolutionize data access at patient

Northern New Mexico regional airport market feasibility

Energy Technology Data Exchange (ETDEWEB)

Drake, R.H.; Williams, D.S.

1998-06-01

This report is about the market for airline travel in northern New Mexico. Interest in developing a northern New Mexico regional airport has periodically surfaced for a number of years. The New Mexico State Legislature passed a memorial during the 1998 Second Session calling for the conduct of a study to determine the feasibility of building a new regional airport in NNM. This report is a study of the passenger market feasibility of such an airport. In addition to commercial passenger market feasibility, there are other feasibility issues dealing with siting, environmental impact, noise, economic impact, intermodal transportation integration, region-wide transportation services, airport engineering requirements, and others. These other feasibility issues are not analyzed in any depth in this report although none were discovered to be show-stoppers as a by-product of the authors doing research on the passenger market itself. Preceding the need for a detailed study of these other issues is the determination of the basic market need for an airport with regular commercial airline service in the first place. This report is restricted to an in-depth look at the market for commercial passenger air service in NNM. 20 figs., 8 tabs.

Remedidal investigation and feasibility study report for the Environmental Restoration Disposal Facility

Energy Technology Data Exchange (ETDEWEB)

Roeck, F.V.

1994-06-01

The purpose of the remedial investigation (RI) is to collect data necessary to adequately characterize the site for the purpose of developing and evaluating effective remedial alternatives. To characterize the site, the lead agency shall, as appropriate, conduct field investigations, including treatability studies, and conduct a baseline risk assessment. The RI provides information to assess the risks to human health and the environment and to support the development, evaluation, and selection of appropriate response alternatives. The primary objective of the feasibility study (FS) is to ensure that appropriate remedial alternatives are developed and evaluated such that relevant information concerning the remedial action options can be presented to a decision-maker and an appropriate remedy selected. The lead agency may develop a feasibility study to address a specific site problem or the entire site. The development and evaluation of alternatives shall reflect the scope and complexity of the remedial action under consideration and the site problems being addressed. Development of alternatives shall be fully integrated with the site characterization activities of the remedial investigation described in paragraph (d) of this section. The lead agency shall include an alternatives screening step, when needed, to select a reasonable number of alternatives for detailed analysis.

Remedidal investigation and feasibility study report for the Environmental Restoration Disposal Facility

International Nuclear Information System (INIS)

Roeck, F.V.

1994-06-01

The purpose of the remedial investigation (RI) is to collect data necessary to adequately characterize the site for the purpose of developing and evaluating effective remedial alternatives. To characterize the site, the lead agency shall, as appropriate, conduct field investigations, including treatability studies, and conduct a baseline risk assessment. The RI provides information to assess the risks to human health and the environment and to support the development, evaluation, and selection of appropriate response alternatives. The primary objective of the feasibility study (FS) is to ensure that appropriate remedial alternatives are developed and evaluated such that relevant information concerning the remedial action options can be presented to a decision-maker and an appropriate remedy selected. The lead agency may develop a feasibility study to address a specific site problem or the entire site. The development and evaluation of alternatives shall reflect the scope and complexity of the remedial action under consideration and the site problems being addressed. Development of alternatives shall be fully integrated with the site characterization activities of the remedial investigation described in paragraph (d) of this section. The lead agency shall include an alternatives screening step, when needed, to select a reasonable number of alternatives for detailed analysis

Studies on the feasibility of heavy ion beams for inertial confinement fusion

International Nuclear Information System (INIS)

1983-05-01

This Annual Report summarizes the scientific results of work carried out in 1982 in the framework of a feasibility study for inertial confinement fusion with heavy ion beams funded by the German Ministry of Research and Technology. The principal aim of this basic research program is the investigation of key problems and the identification of critical issues of the heavy ion ICF concept in the fields of accelerator research, atomic physics, target physics, and reactor design. The research is carried out by about ten working groups at various research centers and universities. One of the highlights in 1982 was a symposium held end of March at GSI which focussed on a critical analysis of the HIBALL accelerator concept. Whereas technical issues and hardware parameters were found feasible the beam dynamics in the storage rings turned out to be beyond the so far believed stability limits. As a consequence a revised accelerator scenario based on a lower charge state and a higher linac current has been investigated during the last year. First considerations were made on an experimental facility necessary for the study of high-intensity beam dynamics and of beam target interaction. Experimental studies of this kind will be of increasing importance for the future of the project. (orig.) [de

Slaughterhouse sewage treatment using gamma radiation - economical feasibility study

International Nuclear Information System (INIS)

Melo, Rita; Botelho, M. Luisa; Branco, Joaquim

2005-01-01

This paper presents preliminary results of a financial viability study for the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry. Five scenarios were studied, including the current practice, representing different types of treatments and goals, e.g.: water reuse and/or sludge add value as agriculture fertilizers. Cost-benefit analysis, including the net present value (NPV) of each scenario, was used as a technique to compare the relative value of various strategies. Taking in account that the initial investment is amortized after 20 years, the implementation of Co-60 treatment with 20% water reuse and sludge application as agriculture fertilizers represents the most profitable project with the highest NPV. Therefore, the implementation of gamma radiation technology on a slaughterhouse wastewater treatment industry is not only technically viable as well as economically feasible. (author)

Preliminary economic feasibility study of MIP (Medical Isotopes Producer)

International Nuclear Information System (INIS)

Mon, G. H.; O, S. Y.

2004-01-01

Preliminary economic feasibility study of MIP (Medical Isotopes Producer), which is used liquid nuclear fuel to produce medical isotopes of Mo-99 and Sr-89, was performed. To do this, this study was estimated the IRR(Internal Rate of Return) and PBP(Pay-back Period) about optimistic and pessimistic cases for market penetration of Asia and U.S.A. isotope markets. And sensitivity analysis is also performed about capital cost and price of Mo-99 and Sr-89. According to the results, IRR was between 14.9% and 24.3%, and PBP was between 4.8 years and 7.8 years. These suggest that MIP has economic merits. MIP can produce other medical isotopes such as Sr-90, I-131, Xe-133, Cs-137. So, it is necessary to do cost-benefit analysis considering production of these other isotopes

Direct solar pumping of semiconductor lasers: A feasibility study

Science.gov (United States)

Anderson, Neal G.

1992-01-01

This report describes results of NASA Grant NAG-1-1148, entitled Direct Solar Pumping of Semiconductor Lasers: A Feasibility Study. The goals of this study were to provide a preliminary assessment of the feasibility of pumping semiconductor lasers in space with directly focused sunlight and to identify semiconductor laser structures expected to operate at the lowest possible focusing intensities. It should be emphasized that the structures under consideration would provide direct optical-to-optical conversion of sunlight into laser light in a single crystal, in contrast to a configuration consisting of a solar cell or storage battery electrically pumping a current injection laser. With external modulation, such lasers could perhaps be efficient sources for intersatellite communications. We proposed specifically to develop a theoretical model of semiconductor quantum-well lasers photopumped by a broadband source, test it against existing experimental data where possible, and apply it to estimating solar pumping requirements and identifying optimum structures for operation at low pump intensities. These tasks have been accomplished, as described in this report of our completed project. The report is organized as follows: Some general considerations relevant to the solar-pumped semiconductor laser problem are discussed in Section 2, and the types of structures chosen for specific investigation are described. The details of the laser model we developed for this work are then outlined in Section 3. In Section 4, results of our study are presented, including designs for optimum lattice-matched and strained-layer solar-pumped quantum-well lasers and threshold pumping estimates for these structures. It was hoped at the outset of this work that structures could be identified which could be expected to operate continuously at solar photoexcitation intensities of several thousand suns, and this indeed turned out to be the case as described in this section. Our project is

Recent progress in the feasibility study for the first nuclear power plant in Indonesia

International Nuclear Information System (INIS)

Adiwardojo

1997-01-01

The energy consumption in Indonesia has been continually increasing since 1970 at an average rate of ∼ 10.6%/year. Specifically, for the island of Java, which consumes ∼ 80% of Indonesia's electricity, the installed capacity by PLN was 6363MW in 1990/91. This has increased by ∼ 17%/year during the past three years. Additional increase in electrical consumption of the Java-Bali system projects the need for the installed capacity to reach 31,845 MW in 2003/04. In anticipation of this major addition of installed capacity, the government of Indonesia is conducting feasibility studies of the nuclear option as a means of filling the projected deficit or gap where other fuel options are likely to reach their limits. This paper describes the scope of the present feasibility study including energy economics and financing, technical and safety aspects, the fuel cycle and waste management, general management, and site and environmental studies. (author). 4 refs, 1 fig., 4 tabs

Feasibility of AmbulanCe-Based Telemedicine (FACT) Study : Safety, Feasibility and Reliability of Third Generation Ambulance Telemedicine

NARCIS (Netherlands)

Yperzeele, Laetitia; Van Hooff, Robbert-Jan; De Smedt, Ann; Espinoza, Alexis Valenzuela; Van Dyck, Rita; Van de Casseye, Rohny; Convents, Andre; Hubloue, Ives; Lauwaert, Door; De Keyser, Jacques; Brouns, Raf

2014-01-01

Background: Telemedicine is currently mainly applied as an in-hospital service, but this technology also holds potential to improve emergency care in the prehospital arena. We report on the safety, feasibility and reliability of in-ambulance teleconsultation using a telemedicine system of the third

Feasibility of exercising adults with asthma: a randomized pilot study

Directory of Open Access Journals (Sweden)

Boyd Amy

2012-08-01

Full Text Available Abstract Background Aerobic exercise appears to have clinical benefits for many asthmatics, yet a complete understanding of the mechanisms underlying these benefits has not been elucidated at this time. Purpose The objective of this study was to determine feasibility for a larger, future study that will define the effect of aerobic exercise on cellular, molecular, and functional measures in adults with mild-moderate asthma. Design Recruited subjects were randomized into usual care (sedentary or usual care with moderate intensity aerobic exercise treatment groups. Setting / Participants Nineteen adults with mild-moderate asthma but without a recent history of exercise were recruited at the UAB Lung Health Center, Birmingham, AL. Intervention The exercise group underwent a 12 week walking program exercising at 60 – 75% of maximum heart rate (HRmax. Subjects self-monitored HRmax levels using heart rate monitors; exercise diaries and recreation center sign-in logs were also used. Main outcome measures Functional measures, including lung function and asthma control scores, were evaluated for all subjects at pre- and post-study time-points; fitness measures were also assessed for subjects in the exercise group. Peripheral blood and nasal lavage fluid were collected from all subjects at pre- and post-study visits in order to evaluate cellular and molecular measures, including cell differentials and eosinophilic cationic protein (ECP. Results Sixteen subjects completed the prescribed protocol. Results show that subjects randomized to the exercise group adhered well (80% to the exercise prescription and exhibited a trend toward improved fitness levels upon study completion. Both groups exhibited improvements in ACQ scores. No changes were observed in lung function (FEV1, FEV1/FVC, cell differentials, or ECP between groups. Conclusions Results indicate that a moderate intensity aerobic exercise training program may improve asthma control and fitness

Optical surface scanning for respiratory motion monitoring in radiotherapy: a feasibility study

DEFF Research Database (Denmark)

Bekke, Susanne Lise; Mahmood, Faisal; Helt-Hansen, Jakob

2014-01-01

Purpose. We evaluated the feasibility of a surface scanning system (Catalyst) for respiratory motion monitoring of breast cancer patients treated with radiotherapy in deep inspiration breath-hold (DIBH). DIBH is used to reduce the radiation dose to the heart and lung. In contrast to RPM, a compet......Purpose. We evaluated the feasibility of a surface scanning system (Catalyst) for respiratory motion monitoring of breast cancer patients treated with radiotherapy in deep inspiration breath-hold (DIBH). DIBH is used to reduce the radiation dose to the heart and lung. In contrast to RPM...... and 3: the Quasar phantom was used to study if the angle of the monitored surface affects the amplitude of the recorded signal. Results. Experiment 1: we observed comparable period estimates for both systems. The amplitudes were 8 ± 0.1 mm (Catalyst) and 4.9 ± 0.1 mm (RPM). Independent check with in...... 1. Experiment 3: an increased (fixed) surface angle during breathing motion resulted in an overestimated amplitude with RPM, while the amplitude estimated by Catalyst was unaffected. Conclusion. Our study showed that Catalyst can be used as a better alternative to the RPM. With Catalyst...

Fibre laser cutting of polycaprolactone sheet for stents manufacturing: A feasibility study

Science.gov (United States)

Guerra, Antonio J.; Farjas, Jordi; Ciurana, Joaquim

2017-10-01

The role of the stent is temporary and it is limited to the intervention and shortly thereafter. Bioresorbable polymer stents were introduced to overcome this problem, making the stent manufacturing process rather difficult considering the complexity of the material. The stent forecast sale makes constant technology development necessary on this field. The adaptation of the laser manufacturing industry to these new materials is costly, thus further studies employing different sorts of lasers are necessary. This paper aims to explore the feasibility of 1.08 μm wavelength fibre laser to cut polycaprolactone sheet, which is especially interesting for long-term implantable devices, such as stents. The laser cut samples were analysed by Differential Scanning Calorimetry (DSC), Tensile Stress Test, and Optical Microscopy in order to study the effects of the laser process over the workpiece. The parameters measured were: taper angle, dimensional precision, material structure changes and mechanical properties changes. Results showed a dimensional precision above 95.75% with a taper angle lower than 0.033°. The laser ablation process has exhibited a minor influence upon material properties. Results exhibit the feasibility of fibre laser to cut polycaprolactone, making the fibre laser an alternative to manufacture stents.

Text-Messaging-Enhanced HIV Intervention for African American Adolescents: A Feasibility Study

Science.gov (United States)

Cornelius, Judith B.; Dmochowski, Jacek; Boyer, Cherrie; St Lawrence, Janet; Lightfoot, Marguerita; Moore, Michael

2013-01-01

We examined the feasibility and acceptability of an HIV prevention intervention for African American adolescents delivered via mobile cell phones and looked at intervention-related changes in beliefs and sexual behaviors. We used a longitudinal one-group comparison design with data collected at three points. Forty adolescents, 13–18 years old, participated in the Becoming a Responsible Teen intervention followed by the delivery of daily multimedia messages for 3 months. The mobile-cell-phone enhanced intervention was feasible and acceptable to the participants. Greater HIV knowledge, improved attitudes toward condoms, and increased perceived HIV risk scores were observed with older adolescents (16–18 years old). Behavior trends showed a decrease in the number of times participants reported engaging in unprotected sexual intercourse over the previous 2 months. Mobile-cell-phone multimedia-text-messaging boosters tested in this study provided preliminary evidence of efficacy of the enhanced HIV prevention intervention for African American youth. PMID:23122907

Technical and economic feasibility study for the creation of a tissue bank

International Nuclear Information System (INIS)

Loncomilla Sandoval, Andrea Rosi; Mendez Guerra, Karina Angelica

2006-01-01

The risk of getting contagious illnesses through applying biological tissues has been one of the paramount worries to be solved since infectious illnesses might be provoked by virus, fungi or bacteria coming from donors or whether they have been introduced by means of intermediate stages before the use of these tissues. Therefore it has been concluded that the tissue allograft must be sterilized. The work presented is a Technical and economic Feasibility Study for the creation of a Tissue Bank in Chile, considering the fact of lacking of such institutions in our country and the need to satisfy the population that requires tissues. It is shown the processes involved and the characteristics of a tissue bank, and also a market survey in order to meet the demand, supply, technical requirements, competitors, opportunities and legal aspects of the process. Finally, it was examined the economic feasibility at which defines the investment, financing and business projections to determine the profitability of the project

Feasibility study of an attention training application for older adults.

Science.gov (United States)

Hill, Nikki L; Mogle, Jacqueline; Colancecco, Elise; Dick, Robert; Hannan, John; Lin, Feng Vankee

2015-09-01

Technology-based attention training has demonstrated promise in its potential to improve cognitive functioning in older people. Developing mobile applications, with older users specifically in mind, may support future dissemination of these interventions and integration into daily life. The purpose of this pilot study was to test the feasibility of an Attention Training Application (ATA) for community-dwelling older adults using mobile technology. A descriptive, mixed-methods design was used to capture older adults' feedback on the usability and acceptability of the ATA. A convenience sample of older adults (n = 9) from two independent living facilities participated in a 2-hour training and practice session with the ATA. Participants were given personally tailored instructions for using the mobile device and the ATA specifically. Following a practice session, participants provided ratings on multiple components of the ATA and completed an audio-recorded, semi-structured interview to provide detailed descriptions of their experience and perceptions. An iterative process of content analysis was used to characterise the open-ended responses. Participants rated the ATA favourably overall on several 0-10 scales including likeability [8.5 (1.6)], interest [8.8 (2.3)] and satisfaction [8.2 (1.9)]. The qualitative analyses revealed several issues relevant to the feasibility of the ATA among older people including the importance of the technological background of the user, limiting negative feedback, challenges with the touch screen interface, personal preferences for challenge, extending the practice period and the difficulty of the dual-task condition. The use of the ATA is feasible in the older adult population. Future development should specifically consider personal characteristics as well as preferences to maximise usability and acceptability among older people. Older adults enjoyed the ATA. This opens doors to user-friendly technological interventions that may be

Feasibility study of fusion breeding blanket concept employing graphite reflector

International Nuclear Information System (INIS)

Cho, Seungyon; Ahn, Mu-Young; Lee, Cheol Woo; Kim, Eung Seon; Park, Yi-Hyun; Lee, Youngmin; Lee, Dong Won

2015-01-01

Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.

Feasibility study of fusion breeding blanket concept employing graphite reflector

Energy Technology Data Exchange (ETDEWEB)

Cho, Seungyon, E-mail: sycho@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Ahn, Mu-Young [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Cheol Woo; Kim, Eung Seon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Yi-Hyun; Lee, Youngmin [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.