WorldWideScience

Sample records for gel electrolytes based

  1. Morphology of Polyvinylidene Fluoride Based Gel Polymer Electrolytes

    Institute of Scientific and Technical Information of China (English)

    田立颖; 黄小彬; 唐小真

    2004-01-01

    Two series of polyvinylidene fluoride (PVDF) based gel polymer electrolytes, with different LiClO4 or propylene carbonate (PC) content, were prepared and analyzed by infrared spectrometer, differential scanning calorimetry, scanning electron microscope and complex impedance spectrometer. The results show that there are great interactions between PVDF, PC and lithium cations. Both LiClO4 and PC content lead to evident change of the morphology of the gel polymer electrolytes. The content of LiClO4 and PC also influences the ionic conductivity of the samples,and an ionic conductivity of above 10-3S·cm-1 can be reached at room temperature.

  2. PMMA-based Gel Polymer Electrolytes with Crosslinking Network

    Institute of Scientific and Technical Information of China (English)

    H.P. Zhang; Y. P. Wu; H. Q. Wu; M. Sun

    2005-01-01

    @@ 1Introduction The lithium-ion battery has a good rate capability and low-temperature performance, but its safety is relatively low due to the possibility of leakage of liquid electrolyte. The use of a solid or gel type electrolyte can lower the probability of leakage liquid electrolyte, and the electrochemical performance of gel electrolyte doesn't decrease so markedly as the solid electrolyte. Now, new types of advanced lithium-ion battery with gel polymer electrolytes are under developing which can be used in the future.

  3. Gelation Behavior of Poly (Vinylidene Fluoride )-based Gel Polymer Electrolyte

    Institute of Scientific and Technical Information of China (English)

    WANG Biao-bing; GU Li-xia

    2006-01-01

    Poly ( vinylidene fluoride ) ( PVdF )-based gel polymer electrolytes with various compositions were prepared by solution casting technique. The kinetics of gelation was analyzed via the correlation between the apparent gelation rate and concentration of PVdF at a given temperature.Combination the results of the kinetics of gelation and the DSC study, it revealed that the phase separation was the major behavior and the fibrils were the major junction joints of the three-dimensional network even in the ease the concentration of PVdF was higher than 25 wt%. The porous surface observed by ESEM also reflected that the phase separation took place during the gelation.

  4. Triol Based Polyurethane Gel Electrolytes for Electrochemical Devices

    Science.gov (United States)

    Kulkarni, A. R.

    2006-06-01

    Polyurethane gel electrolytes with various solvents such as propylene carbonate (PC), propylene carbonate - ethylene carbonate (PC-EC) and γ-butyrolactone - ethylene carbonate (GBL-EC) were synthesized and studied by different characterization tools. Impedance spectroscopy and nuclear magnetic resonance spectroscopy (NMR) provides the insight on ionic mobility in the gel electrolyte. The syneresis effect was studied by observing the weight loss as a function of time. Morphology of the gel electrolyte was investigated by ESEM. Among the various compositions, the maximum conductivity was observed for 35%PU-60%EC/GBL-5%LiClO4. The maximum conductivity of gel electrolytes was found to be 3.98 × 10-3 S/cm at the room temperature, which is higher than that reported in the domain of published literature for the thermoplastic polyurethane family. Moreover, merely 3.5% weight loss was observed for the period of 30 days. The 3.5% wt solvent loss has negligible effect on the conductivity of the gel electrolyte. Test cell was fabricated using polyurethane gel electrolyte and discharge characteristic was studied.

  5. Investigation on poly (vinylidene fluoride) based gel polymer electrolytes

    Indian Academy of Sciences (India)

    S Rajendran; P Sivakumar; Ravi Shanker Babu

    2006-12-01

    An investigation is carried out on gel polymer electrolytes consisting of poly (vinylidene fluoride) (PVdF) as a host polymer, lithium perchlorate (LiClO4), lithium triflate (LiCF3SO3) as salts and mixture of ethylene carbonate (EC) and propylene carbonate (PC) as plasticizers. Polymer thin films were prepared by solvent casting technique and the obtained films were subjected to different characterizations, to confirm their structure, complexation and thermal changes. X-ray diffraction revealed that the salts and plasticizers disrupted the crystalline nature of PVdF based polymer electrolytes and converted them into an amorphous phase. TG/DTA studies showed the thermal stability of the polymer electrolytes. The role of interaction between polymer hosts on conductivity is discussed using the results of a.c. impedance studies. Room temperature (28°C) conductivity of 2.786 × 10-3 Scm-1 was observed in PVdF (24)–EC/PC (68)–LiCF3SO3 (2)/LiClO4 (6) polymer system.

  6. Physical Properties of Substituted Imidazolium Based Ionic Liquids Gel Electrolytes

    Science.gov (United States)

    Sutto, Thomas E.; De Long, Hugh C.; Trulove, Paul C.

    2002-11-01

    The physical properties of solid gel electrolytes of either polyvinylidene diflurohexafluoropropylene or a combination of polyvinylidene hexafluoropropylene and polyacrylic acid, and the molten salts 1-ethyl-3-methylimidazolium tetrafluoroborate, 1,2-dimethyl-3-n-propylimidazolium tetrafluoroborate, and the new molten salts 1,2-dimethyl-3-n-butylimidazolium tetrafluoroborate, and 1,2-dimethyl-3-n-butylimidazolium hexafluorophosphate were characterized by temperature dependent ionic conductivity measurements for both the pure molten salt and of the molten salt with 0.5 M Li+ present. Ionic conductivity data indicate that for each of the molten salts, the highest concentration of molten salt allowable in a single component polymer gel was 85%, while gels composed of 90%molten salt were possible when using both polyvinylidene hexafluorophosphate and polyacrylic acid. For polymer gel composites prepared using lithium containing ionic liquids, the optimum polymer gel composite consisted of 85% of the 0.5 M Li+/ionic liquid, 12.75% polyvinylidene hexafluoropropylene, and 2.25% poly (1-carboxyethylene). The highest ionic conductivity observed was for the gel containing 90%1-ethyl-3-methyl-imidazolium tetrafluoroborate, 9.08 mS/cm. For the lithium containing ionic liquid gels, their ionic conductivity ranged from 1.45 to 0.05 mS/cm, which is comparable to the value of 0.91 mS/cm, observed for polymer composite gels containing 0.5 M LiBF4 in propylene carbonate.

  7. Structural and Electrochemical Analysis of PMMA Based Gel Electrolyte Membranes

    Directory of Open Access Journals (Sweden)

    Chithra M. Mathew

    2015-01-01

    Full Text Available New gel polymer electrolytes containing poly(vinylidene chloride-co-acrylonitrile and poly(methyl methacrylate are prepared by solution casting method. With the addition of 60 wt.% of EC to PVdC-AN/PMMA blend, ionic conductivity value 0.398×10-6 S cm−1 has been achieved. XRD and FT-IR studies have been conducted to investigate the structure and complexation in the polymer gel electrolytes. The FT-IR spectra show that the functional groups C=O and C≡N play major role in ion conduction. Thermal stability of the prepared membranes is found to be about 180°C.

  8. Gel-based composite polymer electrolytes with novel hierarchical mesoporous silica network for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xiaoliang; Cai Qiang [Department of Materials Science and Engineering, and State Key Laboratory of New Ceramics and Fine Processing, Tsinghua University, Beijing 100084 (China); Fan Lizhen [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Hua Tao; Lin Yuanhua [Department of Materials Science and Engineering, and State Key Laboratory of New Ceramics and Fine Processing, Tsinghua University, Beijing 100084 (China); Nan Cewen [Department of Materials Science and Engineering, and State Key Laboratory of New Ceramics and Fine Processing, Tsinghua University, Beijing 100084 (China)], E-mail: cwnan@tsinghua.edu.cn

    2008-11-15

    In the present work, novel gel-based composite polymer electrolytes for lithium batteries were prepared by introducing a hierarchical mesoporous silica network to the poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)-based gel electrolytes. As compared with the PVDF-HFP-based gel electrolytes with/without conventional nano-sized silica fillers, the novel electrolytes have shown more homogeneous microstructure, higher ionic conductivity and better mechanical stability, which could be caused by the strong silica network and the effective interactions among the polymer, the liquid electrolytes and the silica. Moreover, the cell with this kind of electrolytes could achieve a discharge capacity as much as 150 mAh g{sup -1} at room temperature (LiCoO{sub 2} as the cathode active material), with high Coulomb efficiency.

  9. Gel-based composite polymer electrolytes with novel hierarchical mesoporous silica network for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiao-Liang; Cai, Qiang; Hua, Tao; Lin, Yuan-Hua; Nan, Ce-Wen [Department of Materials Science and Engineering, and State Key Laboratory of New Ceramics and Fine Processing, Tsinghua University, Beijing 100084 (China); Fan, Li-Zhen [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China)

    2008-11-15

    In the present work, novel gel-based composite polymer electrolytes for lithium batteries were prepared by introducing a hierarchical mesoporous silica network to the poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)-based gel electrolytes. As compared with the PVDF-HFP-based gel electrolytes with/without conventional nano-sized silica fillers, the novel electrolytes have shown more homogeneous microstructure, higher ionic conductivity and better mechanical stability, which could be caused by the strong silica network and the effective interactions among the polymer, the liquid electrolytes and the silica. Moreover, the cell with this kind of electrolytes could achieve a discharge capacity as much as 150 mAh g{sup -1} at room temperature (LiCoO{sub 2} as the cathode active material), with high Coulomb efficiency. (author)

  10. Performance enhancement of phosphoric acid fuel cell using phosphosilicate gel based electrolyte

    Institute of Scientific and Technical Information of China (English)

    Kajari Kargupta; Swati Saha; Dipali Banerjee; Mrinal Seal; Saibal Ganguly

    2012-01-01

    Replacement of phosphoric acid electrolyte by phosphosilicate gel based electrolytes is proposed for performance enhancement of phosphoric acid fuel cell (PAFG).Phosphosilicate gel in paste form and in powder form is synthesized from tetraethoxysilane and orthophosphoric acid using sol-gel method for two different P/Si ratio of 5 and 1.5 respectively.Replacement of phosphoric acid electrolyte by phosphosilicate gel paste enhances the peak power generation of the fuel cell by 133% at 120 ℃ cell temperature; increases the voltage generation in the ohmic regime and extends the maximum possible load current.Polyinyl alcohol (PVA) is used to bind the phosphosilicate gel powder and to form the hybrid crosslinked gel polymer electrolyte membrane.Soaking the membrane with phosphoric acid solution,instead of that with water improves the proton conductivity of the membrane,enhances the voltage and power generation by the fuel cell and extends the maximum possible operating temperature.At lower operating temperature of 70 ℃,peak power produced by phosphosilicate gel polymer electrolyte membrane fuel cell ( PGMFC ) is increased by 40% compared to that generated by phosphoric acid fuel cell ( PAFC ).However,the performance of composite membrane diminishes as the cell temperature increases.Thus phosphosilicate gel in paste form is found to be a good alternative of phosphoric acid electrolyte at medium operating temperature range while phosphosilicate gel-PVA composite offers performance enhancement at low operating temperatures.

  11. Effect of conductive additives to gel electrolytes on activated carbon-based supercapacitors

    Directory of Open Access Journals (Sweden)

    Farshad Barzegar

    2015-09-01

    Full Text Available This article is focused on polymer based gel electrolyte due to the fact that polymers are cheap and can be used to achieve extended potential window for improved energy density of the supercapacitor devices when compared to aqueous electrolytes. Electrochemical characterization of a symmetric supercapacitor devices based on activated carbon in different polyvinyl alcohol (PVA based gel electrolytes was carried out. The device exhibited a maximum energy density of 24 Wh kg−1 when carbon black was added to the gel electrolyte as conductive additive. The good energy density was correlated with the improved conductivity of the electrolyte medium which is favorable for fast ion transport in this relatively viscous environment. Most importantly, the device remained stable with no capacitance lost after 10,000 cycles.

  12. Novel Amphiphilic Polymer Gel Electrolytes Based on PEG-b-GMA-co-MMA

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    1 Results Gel polymer electrolytes for lithium battery have been widely investigated recently because of their high ion conductivity at room temperature. We synthesized and characterized novel gel electrolytes based on amphiphilic copolymethacrylates containing different lengths of ethylene oxide (EO) chain as ionophilic units and methyl methacrylate (MMA) chain as ionophobic units[1]. Their electrochemical properties were also measured.1H NMR and FTIR analysis results elucidated that PEG-b-glycidyl met...

  13. Gel electrolytes and electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Fleischmann, Sven; Bunte, Christine; Mikhaylik, Yuriy V.; Viner, Veronika G.

    2017-09-05

    Gel electrolytes, especially gel electrolytes for electrochemical cells, are generally described. In some embodiments, the gel electrolyte layers comprise components a) to c). Component a) may be at least one layer of at least one polymer comprising polymerized units of: a1) at least one monomer containing an ethylenically unsaturated unit and an amido group and a2) at least one crosslinker. Component b) may be at least one conducting salt and component c) may be at least one solvent. Electrodes may comprise the components a), d) and e), wherein component a) may be at least one layer of at least one polymer as described herein. Component d) may be at least one electroactive layer and component e) may be at least one ceramic layer. Furthermore, electrochemical cells comprising component a) which may be at least one layer of at least one polymer as described herein, are also provided.

  14. Stability of poly(vinylidene fluoride-co-hexafluoropropylene)-based composite gel electrolytes with functionalized silicas

    Energy Technology Data Exchange (ETDEWEB)

    Walkowiak, Mariusz [Central Laboratory of Batteries and Cells, Forteczna 12 St., 61-362 Poznan (Poland); Zalewska, Aldona [Warsaw University of Technology, Department of Chemistry, Noakowskiego 3 St., 00-664 Warsaw (Poland); Jesionowski, Teofil [Poznan University of Technology, Institute of Chemical Technology and Engineering, Marii Sklodowskiej-Curie 2 Sq., 60-965 Poznan (Poland); Pokora, Monika [Central Laboratory of Batteries and Cells, Forteczna 12 St., 61-362 Poznan (Poland); Poznan University of Technology, Institute of Chemical Technology and Engineering, Marii Sklodowskiej-Curie 2 Sq., 60-965 Poznan (Poland)

    2007-11-15

    Various aspects of stability of composite polymer gel electrolytes based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF/HFP) polymeric matrix and functionalized precipitated silicas have been studied. The silica fillers have been surface modified with methacryloxy or vinyl groups by partially replacing silanol groups, so that bi-functional (hydrophilic/hydrophobic) character of the inorganic fillers was created. Compatibility of the gel electrolytes with lithium electrode has been examined by means of EIS technique. Electrochemical stability window has been studied with the application of cyclic voltammetry technique with fast sweeping rate. Passive layer formation on graphite electrode has been investigated for all the gel electrolytes by means of cyclic voltammetry with slow scan rate and galvanostatic charging/discharging technique. It has been shown that stability of the interface between lithium and gel electrolyte is significantly improved when bi-functional silicas are used as fillers. The phenomenon has been ascribed to more effective scavenging of trace impurities as well as to better shielding of the electrode surfaces. Cyclic voltammetry on platinum has revealed excessive electrochemical redox processes upon prolonged cycling for all the gel electrolytes. It has been demonstrated that stable passive layers are formed on graphite electrodes upon electrochemical reduction in the presence of the studied composite polymer gel electrolytes. (author)

  15. Studies on Gel Electrolyte Based on Nitrile-Butadiene Copolymers

    Science.gov (United States)

    1993-06-01

    preparation of a hybrid electrolyte, suitable for solid-polymer batteries. Based on the study of ionic conductivity in the presence of LiBF4 of a...lithium salts in different plasticizers showed the highest conductivity for LiBF4 . Conductivity of LiBF4 in different plasticizers decreases in the order...GLASS TRANSITION 53 TEMPERATURE OF VARIOUS NBR COPOLYMERS WITH AND WITHOUT LiBF4 APPENDIX B: ANOMALY IN THE IONIC 63 CONDUCTIVITY-TEMPERATURE STUDIES

  16. Study on the Ion Association in PVdF-based Gel Polymer Electrolyte

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Gel polymer electrolytes based on the poly (vinylidene fluoride) (PVdF) and the electrolyte of LiClO4 in propylene carbonate (PC) were prepared by the solution casting technique. The ionic conductivity of the gel electrolytes was concentration of lithium salt. Because of the strong coulombiq attractions, the dissolved salt ions might aggregate into ion pairs and multiple ion aggregates. The analysis of DSC and X-ray diffraction revealed that the ions association occurred at higher concentration of lithium salt.

  17. A flexible Li polymer primary cell with a novel gel electrolyte based on poly(acrylonitrile)

    Science.gov (United States)

    Akashi, Hiroyuki; Tanaka, Ko-ichi; Sekai, Koji

    The performance of a Li polymer primary cell with fire-retardant poly(acrylonitrile) (PAN)-based gel electrolytes is reported. By optimizing electrodes, electrolytes, the packaging material, and the structural design of the polymer cell, we succeeded in developing a "film-like" Li polymer primary cell with sufficient performance for practical use. The cell is flexible and less than 0.5 mm thick, which makes it suitable for a power source for some smart devices, such as an IC card. Fast cation conduction in the gel electrolyte minimizes the drop of the discharge capacity even at -20 °C. The high chemical stability of the gel electrolytes and the new packaging material allow the self-discharge rate to be limited to under 4.3%, which is equivalent to that of conventional coin-shaped or cylindrical Li-MnO 2 cells.

  18. Design of polyacene-based negative electrode for polymeric gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimoto, Nobuko; Okamoto, Atsushi; Morita, Masayuki [Department of Applied Chemistry and Chemical Engineering, Faculty of Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube 755-8611 (Japan); Ando, Nobuo; Hato, Yukinori [Material Development, Kanebo Ltd., 4-1 Kanebo-cho, Hofu 747-0823 (Japan)

    2005-08-26

    Composition of polyacene (PAS)-based negative electrode has been optimized to be suitable for rechargeable battery systems with polymeric gel electrolytes. The gel electrolytes consisted of poly(vinylidenefluoride-co-hexafluoropropylrne) (PVdF-HFP) as a host polymer, a mixture of ethylene carbonate (EC) and diethyl carbonate (DEC) as a plasticizer, and LiX (X=ClO{sub 4} or (C{sub 2}F{sub 5}SO{sub 2}){sub 2}N) as a carrier salt. Three types of composite PAS electrodes were prepared and their compatibility with the polymeric gel electrolytes was examined. A half cell assembled with the composite PAS electrode containing proper amounts of polymeric gel and the electrolyte film with the same gel composition showed good cycling characteristics. The gel composition containing 1.0moldm{sup -3} (M) Li(C{sub 2}F{sub 5}SO{sub 2}){sub 2}N/(EC+DEC) gave discharge capacity of about 600Ahkg{sup -1} (with respect to the mass of PAS) with high rechargeability. (author)

  19. Role of polyvinyl alcohol in the conductivity behaviour of polyethylene glycol-based composite gel electrolytes

    Indian Academy of Sciences (India)

    S K Patel; R B Patel; A Awadhia; N Chand; S L Agrawal

    2007-09-01

    An attempt has been made in the present work to combine gel and composite polymer electrolyte routes together to form a composite polymeric gel electrolyte that is expected to possess high ionic conductivity with good mechanical integrity. Polyethylene glycol (PEG) based composite gel electrolytes using polyvinyl alcohol (PVA) as guest polymer have been synthesized with 1 molar solution of ammonium thiocyanate (NH4SCN) in dimethyl sulphoxide (DMSO) and electrically characterized. The ionic conductivity measurements indicate that PEG : PVA : NH4SCN-based composite gel electrolytes are superior (max = 5.7 × 10−2 S cm-1) to pristine electrolytes (PEG : NH4SCN system) and conductivity variation with filler concentration remains within an order of magnitude. The observed conductivity maxima have been correlated to PEG : PVA : NH4SCN- and PVA : NH4SCN-type complexes. Temperature dependence of conductivity profiles exhibits Arrhenius behaviour in low temperature regime followed by VTF character at higher temperature.

  20. Gel polymer electrolytes for batteries

    Science.gov (United States)

    Balsara, Nitash Pervez; Eitouni, Hany Basam; Gur, Ilan; Singh, Mohit; Hudson, William

    2014-11-18

    Nanostructured gel polymer electrolytes that have both high ionic conductivity and high mechanical strength are disclosed. The electrolytes have at least two domains--one domain contains an ionically-conductive gel polymer and the other domain contains a rigid polymer that provides structure for the electrolyte. The domains are formed by block copolymers. The first block provides a polymer matrix that may or may not be conductive on by itself, but that can soak up a liquid electrolyte, thereby making a gel. An exemplary nanostructured gel polymer electrolyte has an ionic conductivity of at least 1.times.10.sup.-4 S cm.sup.-1 at 25.degree. C.

  1. DSC and conductivity studies on PVA based proton conducting gel electrolytes

    Indian Academy of Sciences (India)

    S L Agrawal; Arvind Awadhia

    2004-12-01

    An attempt has been made in the present work to prepare polyvinyl alcohol (PVA) based proton conducting gel electrolytes in ammonium thiocyanate (NH4SCN) solution and characterize them. DSC studies affirm the formation of gels along with the presence of partial complexes. The cole–cole plots exhibit maximum ionic conductivity (2.58 × 10-3 S cm-1) for gel samples containing 6 wt% of PVA. The conductivity of gel electrolytes exhibit liquid like nature at low polymer concentrations while the behaviour is seen to be affected by the formation of PVA–NH4SCN complexes upon increase in polymer content beyond 5 wt%. Temperature dependence of ionic conductivity exhibits VTF behaviour.

  2. Water-based thixotropic polymer gel electrolyte for dye-sensitized solar cells.

    Science.gov (United States)

    Park, Se Jeong; Yoo, Kichoen; Kim, Jae-Yup; Kim, Jin Young; Lee, Doh-Kwon; Kim, Bongsoo; Kim, Honggon; Kim, Jong Hak; Cho, Jinhan; Ko, Min Jae

    2013-05-28

    For the practical application of dye-sensitized solar cells (DSSCs), it is important to replace the conventional organic solvents based electrolyte with environmentally friendly and stable ones, due to the toxicity and leakage problems. Here we report a noble water-based thixotropic polymer gel electrolyte containing xanthan gum, which satisfies both the environmentally friendliness and stability against leakage and water intrusion. For application in DSSCs, it was possible to infiltrate the prepared electrolyte into the mesoporous TiO2 electrode at the fluidic state, resulting in sufficient penetration. As a result, this electrolyte exhibited similar conversion efficiency (4.78% at 100 mW cm(-2)) and an enhanced long-term stability compared to a water-based liquid electrolyte. The effects of water on the photovoltaic properties were examined elaborately from the cyclic voltammetry curves and impedance spectra. Despite the positive shift in the conduction band potential of the TiO2 electrode, the open-circuit voltage was enhanced by addition of water in the electrolyte due to the greater positive shift in the I(-)/I3(-) redox potential. However, due to the dye desorption and decreased diffusion coefficient caused by the water content, the short-circuit photocurrent density was reduced. These results will provide great insight into the development of efficient and stable water-based electrolytes.

  3. Phthaloylchitosan-Based Gel Polymer Electrolytes for Efficient Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    S. N. F. Yusuf

    2014-01-01

    Full Text Available Phthaloylchitosan-based gel polymer electrolytes were prepared with tetrapropylammonium iodide, Pr4NI, as the salt and optimized for conductivity. The electrolyte with the composition of 15.7 wt.% phthaloylchitosan, 31.7 wt.% ethylene carbonate (EC, 3.17 wt.% propylene carbonate (PC, 19.0 wt.% of Pr4NI, and 1.9 wt.% iodine exhibits the highest room temperature ionic conductivity of 5.27 × 10−3 S cm−1. The dye-sensitized solar cell (DSSC fabricated with this electrolyte exhibits an efficiency of 3.5% with JSC of 7.38 mA cm−2, VOC of 0.72 V, and fill factor of 0.66. When various amounts of lithium iodide (LiI were added to the optimized gel electrolyte, the overall conductivity is observed to decrease. However, the efficiency of the DSSC increases to a maximum value of 3.71% when salt ratio of Pr4NI : LiI is 2 : 1. This cell has JSC, VOC and fill factor of 7.25 mA cm−2, 0.77 V and 0.67, respectively.

  4. Structural and electrochemical properties of succinonitrile-based gel polymer electrolytes: role of ionic liquid addition.

    Science.gov (United States)

    Suleman, Mohd; Kumar, Yogesh; Hashmi, S A

    2013-06-20

    Experimental studies on the novel compositions of gel polymer electrolytes, comprised of plastic crystal succinonitrile (SN) dispersed with pyrrolidinium and imidazolium-based ionic liquids (ILs) entrapped in a host polymer poly(vinylidine fluoride-co-hexafluoropropylene) (PVdF-HFP), are reported. The gel electrolytes are in the form of free-standing films with excellent mechanical, thermal, and electrochemical stability. The introduction of even a small content (~1 wt %) of ionic liquid (1-butyl-1-methylpyrrolidinium bis(trifluoromethyl-sulfonyl)imide (BMPTFSI) or 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMITf) in the PVdF-HFP/SN system (1:4 w/w) enhances the electrical conductivity by 4 orders of magnitude, that is, from ~10(-7) to ~10(-3) S cm(-1) at room temperature. The structural changes due to the entrapment of SN or SN/ILs mixtures and ion-SN-polymer interactions are examined by Fourier transform infrared (FTIR)/Raman spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimmetry (DSC). Various physicochemical properties and fast ion conduction in the gel polymer membranes show their promising characteristics as electrolytes in different ionic devices including supercapacitors.

  5. Gel polymer electrolytes based on nanofibrous polyacrylonitrile–acrylate for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dul-Sun [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Woo, Jang Chang [Department of Textile Engineering, Inha University, 100 Inharo, Nam-gu Incheon 402-751 (Korea, Republic of); Youk, Ji Ho, E-mail: youk@inha.ac.kr [Department of Textile Engineering, Inha University, 100 Inharo, Nam-gu Incheon 402-751 (Korea, Republic of); Manuel, James [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Ahn, Jou-Hyeon, E-mail: jhahn@gnu.ac.kr [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Department of Materials Engineering and Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of)

    2014-10-15

    Graphical abstract: - Highlights: • Nanofibrous polyacrylonitrile–acrylate membranes were prepared by electrospinning. • Trimethylolpropane triacrylate was used as a crosslinking agent of fibers. • The GPE based on PAN–acrylate (1/0.5) showed good electrochemical properties. - Abstract: Nanofibrous membranes for gel polymer electrolytes (GPEs) were prepared by electrospinning a mixture of polyacrylonitrile (PAN) and trimethylolpropane triacrylate (TMPTA) at weight ratios of 1/0.5 and 1/1. TMPTA is used to achieve crosslinking of fibers thereby improving mechanical strength. The average fiber diameters increased with increasing TMPTA concentration and the mechanical strength was also improved due to the enhanced crosslinking of fibers. GPEs based on electrospun membranes were prepared by soaking them in a liquid electrolyte of 1 M LiPF{sub 6} in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1, v/v). The electrolyte uptake and ionic conductivity of GPEs based on PAN and PAN–acrylate (weight ratio; 1/1 and 1/0.5) were investigated. Ionic conductivity of GPEs based on PAN–acrylate was the highest for PAN/acrylate (1/0.5) due to the proper swelling of fibers and good affinity with liquid electrolyte. Both GPEs based on PAN and PAN–acrylate membranes show good oxidation stability, >5.0 V vs. Li/Li{sup +}. Cells with GPEs based on PAN–acrylate (1/0.5) showed remarkable cycle performance with high initial discharge capacity and low capacity fading.

  6. Supercapacitors based on two dimensional VO2 nanosheet electrodes in organic gel electrolyte

    KAUST Repository

    Rakhi, R.B.

    2016-10-16

    VO2 is a low band-gap semiconductor with relatively high conductivity among transition metal oxides, which makes it an interesting material for supercapacitor electrode applications. The performance of VO2 as supercapacitor electrode in organic electrolytes has never been reported before. Herein, two-dimensional nanosheets of VO2 are prepared by the simultaneous solution reduction and exfoliation from bulk V2O5 powder by hydrothermal method. A specific capacitance of 405 Fg−1 is achieved for VO2 based supercapacitor in an organic electrolyte, in three electrode configuration. The symmetric capacitor based on VO2 nanosheet electrodes and the liquid organic electrolyte exhibits an energy density of 46 Wh kg−1 at a power density of 1.4 kW kg−1 at a constant current density of 1 Ag−1. Furthermore, flexible solid-state supercapacitors are fabricated using same electrode material and Alumina-silica based gel electrolyte. The solid-state device delivers a specific capacitance of 145 Fg−1 and a device capacitance of 36 Fg−1 at a discharge current density of 1 Ag−1. Series combination of three solid state capacitors is capable of lighting up a red LED for more than 1 minute.

  7. Room temperature lithium metal batteries based on a new Gel Polymer Electrolyte membrane

    Science.gov (United States)

    Sannier, L.; Bouchet, R.; Grugeon, S.; Naudin, E.; Vidal, E.; Tarascon, J.-M.

    A new effective Gel Polymer Electrolyte membrane based on two polymers, the polyethylene oxide (PEO), a poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) copolymer and a plasticizer, the dibutylphtalate (DBP), was realized. This separator membrane was made by adjunction, through lamination, of an industrially made DBP/PVdF-HFP film and a homemade DBP/PEO thin film. Once the plasticizer was removed and the separator gelled by the electrolyte, the PEO enables the formation of a good interface with the lithium while the PVdF-HFP film brings the mechanical strength to the membrane. The electrochemical behavior of lithium batteries based on this bi-layer separator was investigated versus temperature, cycling potential and cycling rate. Owing to the promising results obtained with laboratory cells, a 1 Ah prototype was successfully assembled, and its cycling and rate performances were reported.

  8. Crosslinked polymer gel electrolytes based on polyethylene glycol methacrylate and ionic liquid for lithium battery applications

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Chen [ORNL; Sun, Xiao-Guang [ORNL; Dai, Sheng [ORNL

    2013-01-01

    Gel polymer electrolytes were synthesized by copolymerization polyethylene glycol methyl ether methacrylate with polyethylene glycol dimethacrylate in the presence of a room temperature ionic liquid, methylpropylpyrrolidinium bis(trifluoromethanesulfonyl)imide (MPPY TFSI). The physical properties of gel polymer electrolytes were characterized by thermal analysis, impedance spectroscopy, and electrochemical tests. The ionic conductivities of the gel polymer electrolytes increased linearly with the amount of MPPY TFSI and were mainly attributed to the increased ion mobility as evidenced by the decreased glass transition temperatures. Li||LiFePO4 cells were assembled using the gel polymer electrolytes containing 80 wt% MPPY TFSI via an in situ polymerization method. A reversible cell capacity of 90 mAh g 1 was maintained under the current density of C/10 at room temperature, which was increased to 130 mAh g 1 by using a thinner membrane and cycling at 50 C.

  9. Preparation of a Star Network PEG-based Gel Polymer Electrolyte and Its Application to Electrochromic Devices

    Institute of Scientific and Technical Information of China (English)

    GONG Yong-Feng; FU Xiang-Kai; ZHANG Shu-Peng; JIANG Qing-Long

    2007-01-01

    A star network polymer with a pentaerythritol core linking four PEG-block polymeric arms was synthesized,and its corresponding gel polymer electrolyte based on lithium perchlorate and plasticizers EC/PC with the character being colorless and highly transparent has been also prepared. The polymer host was characterized and confirmed to be of a star network and an amorphous structure by FTIR, 1H NMR and XRD studies. The polymer host hold good mechanical properties for pentaerythritol cross-linking. Maximum ionic conductivity of the prepared electrolyte showed that the thermal stability was up to at least 150 ℃. The gel polymer electrolyte was further evaluated in electrochromic devices fabricated by transparent PET-ITO and electrochromically active viologen derivative films, and its excellent performance promised the usage of the gel polymer electrolyte as ionic conductor material in electrochrornic devices.

  10. Thermostable gel polymer electrolyte based on succinonitrile and ionic liquid for high-performance solid-state supercapacitors

    Science.gov (United States)

    Pandey, Gaind P.; Liu, Tao; Hancock, Cody; Li, Yonghui; Sun, Xiuzhi Susan; Li, Jun

    2016-10-01

    A flexible, free-standing, thermostable gel polymer electrolyte based on plastic crystalline succinonitrile (SN) and ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate (BMImBF4) entrapped in copolymer poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) is prepared and optimized for application in solvent-free solid-state supercapacitors. The synthesized gel polymer electrolyte exhibits a high ionic conductivity over a wide temperature range (from ∼5 × 10-4 S cm-1 at -30 °C up to ∼1.5 × 10-2 S cm-1 at 80 °C) with good electrochemical stability window (-2.9 to 2.5 V). Thermal studies confirm that the SN containing gel polymer electrolyte remains stable in the same gel phase over a wide temperature range from -30 to 90 °C. The electric double layer capacitors (EDLCs) have been fabricated using activated carbon as active materials and new gel polymer electrolytes. Electrochemical performance of the EDLCs is assessed through cyclic voltammetry, galvanostatic charge-discharge cycling and impedance spectroscopy. The EDLC cells with the proper SN-containing gel polymer electrolyte has been found to give high specific capacitance 176 F g-1 at 0.18 A g-1 and 138 F g-1 at 8 A g-1. These solid-state EDLC cells show good cycling stability and the capability to retain ∼80% of the initial capacitance after 10,000 cycles.

  11. Design of poly(acrylonitrile)-based gel electrolytes for high-performance lithium ion batteries.

    Science.gov (United States)

    Wang, Shih-Hong; Kuo, Ping-Lin; Hsieh, Chien-Te; Teng, Hsisheng

    2014-11-12

    The use of polyacrylonitrile (PAN) as a host for gel polymer electrolytes (GPEs) commonly produces a strong dipole-dipole interaction with the polymer. This study presents a strategy for the application of PAN in GPEs for the production of high performance lithium ion batteries. The resulting gel electrolyte GPE-AVM comprises a poly(acrylonitrile-co-vinyl acetate) copolymer blending poly(methyl methacrylate) as a host, which is swelled using a liquid electrolyte (LE) of 1 M LiPF6 in carbonate solvent. Vinyl acetate and methacrylate groups segregate the PAN chains in the GPE, which produces high ionic conductivity (3.5 × 10 (-3) S cm(-1) at 30 °C) and a wide electrochemical voltage range (>6.5 V) as well as an excellent Li(+) transference number of 0.6. This study includes GPE-AVM in a full-cell battery comprising a LiFePO4 cathode and graphite anode to promote ion motion, which reduced resistance in the battery by 39% and increased the specific power by 110%, relative to the performance of batteries based on LE. The proposed GPE-based battery has a capacity of 140 mAh g(-1) at a discharge rate of 0.1 C and is able to deliver 67 mAh g(-1) of electricity at 17 C. The proposed GPE-AVM provides a robust interface with the electrodes in full-cell batteries, resulting in 93% capacity retention after 100 charge-discharge cycles at 17 C and 63% retention after 1000 cycles.

  12. Experimental investigations of an ionic-liquid-based, magnesium ion conducting, polymer gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, G.P.; Hashmi, S.A. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2009-02-15

    Studies on a novel magnesium ion conducting gel polymer electrolyte based on a room temperature ionic liquid (RTIL) is reported. It comprises a Mg-salt, Mg(CF{sub 3}SO{sub 3}){sub 2} [or magnesium triflate, Mg(Tf){sub 2}] solution in an ionic liquid, 1-ethyl-3-methylimidazolium trifluoro-methanesulfonate (EMITf), immobilized with poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP), which is a freestanding, semitransparent and flexible film with excellent mechanical strength. Physical and electrochemical analyses demonstrate promising characteristics of these films, suitable as electrolytes in rechargeable magnesium batteries. The material offers a maximum electrical conductivity of {proportional_to}4.8 x 10{sup -3} S cm{sup -1} at room temperature (20 C) with excellent thermal and electrochemical stabilities. Possible conformational changes in the polymer host PVdF-HFP due to ionic liquid solution entrapment and ion-polymer interaction are investigated by Fourier transform infra-red (FTIR), X-ray diffraction (XRD) and scanning electron microscopic (SEM) methods. The Mg{sup 2+} ion transport in the gel film is confirmed from cyclic voltammetry, impedance and transport number measurements. The Mg{sup 2+} ion transport number (t{sub +}) is {proportional_to}0.26, which indicates a substantial contribution of triflate anion transport along with ionic conduction due to the component ions of the ionic liquid. (author)

  13. Experimental investigations of an ionic-liquid-based, magnesium ion conducting, polymer gel electrolyte

    Science.gov (United States)

    Pandey, G. P.; Hashmi, S. A.

    Studies on a novel magnesium ion conducting gel polymer electrolyte based on a room temperature ionic liquid (RTIL) is reported. It comprises a Mg-salt, Mg(CF 3SO 3) 2 [or magnesium triflate, Mg(Tf) 2] solution in an ionic liquid, 1-ethyl-3-methylimidazolium trifluoro-methanesulfonate (EMITf), immobilized with poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP), which is a freestanding, semitransparent and flexible film with excellent mechanical strength. Physical and electrochemical analyses demonstrate promising characteristics of these films, suitable as electrolytes in rechargeable magnesium batteries. The material offers a maximum electrical conductivity of ∼4.8 × 10 -3 S cm -1 at room temperature (20 °C) with excellent thermal and electrochemical stabilities. Possible conformational changes in the polymer host PVdF-HFP due to ionic liquid solution entrapment and ion-polymer interaction are investigated by Fourier transform infra-red (FTIR), X-ray diffraction (XRD) and scanning electron microscopic (SEM) methods. The Mg 2+ ion transport in the gel film is confirmed from cyclic voltammetry, impedance and transport number measurements. The Mg 2+ ion transport number (t +) is ∼0.26, which indicates a substantial contribution of triflate anion transport along with ionic conduction due to the component ions of the ionic liquid.

  14. PREPARATION OF STAR NETWORK PEG-BASED GEL POLYMER ELECTROLYTES FOR ELECTROCHROMIC DEVICES

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    An amorphous,colorless,and highly transparent star network polymer with a pentaerythritol core linking four PEG-block polymeric arms was synthesized from the poly(ethylene glycol)(PEG),pentaerythritol,and dichloromethane by Williamson reaction.FTIR and 1H-NMR measurement demonstrated that the polymer repeating units were C[CH2-OCH2O-(CH2CH2O)m-CH2O-(CH2CH2O)n-CH2O]4.The polymer host held well mechanical properties for pentaerythritol cross-linking.The gel polymer electrolytes based on Lithium perchlorate(LiClO4)and ethylene carbonate/propylene carbonate(EC/PC)were prepared and characterized by AC impedance spectroscopy and thermogravimetry(TG),the results showed thermal stability up to at least 150℃ and ionic conductivity reaching 8.83×fabricated by transparent PET-ITO and electrochromic active viologen derivative films,and its excellent performance promised the usage of the gel polymer electrolytes as ionic conductor material in ECD.

  15. Li Ion Conducting Polymer Gel Electrolytes Based on Ionic Liquid/PVDF-HFP Blends.

    Science.gov (United States)

    Ye, Hui; Huang, Jian; Xu, Jun John; Khalfan, Amish; Greenbaum, Steve G

    2007-09-21

    Ionic liquids thermodynamically compatible with Li metal are very promising for applications to rechargeable lithium batteries. 1-methyl-3-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (P(13)TFSI) is screened out as a particularly promising ionic liquid in this study. Dimensionally stable, elastic, flexible, nonvolatile polymer gel electrolytes (PGEs) with high electrochemical stabilities, high ionic conductivities and other desirable properties have been synthesized by dissolving Li imide salt (LiTFSI) in P(13)TFSI ionic liquid and then mixing the electrolyte solution with poly(vinylidene-co-hexafluoropropylene) (PVDF-HFP) copolymer. Adding small amounts of ethylene carbonate to the polymer gel electrolytes dramatically improves the ionic conductivity, net Li ion transport concentration, and Li ion transport kinetics of these electrolytes. They are thus favorable and offer good prospects in the application to rechargeable Li batteries including open systems like Li/air batteries, as well as more "conventional" rechargeable lithium and lithium ion batteries.

  16. Li Ion Conducting Polymer Gel Electrolytes Based on Ionic Liquid/PVDF-HFP Blends

    Science.gov (United States)

    Ye, Hui; Huang, Jian; Xu, Jun John; Khalfan, Amish; Greenbaum, Steve G.

    2009-01-01

    Ionic liquids thermodynamically compatible with Li metal are very promising for applications to rechargeable lithium batteries. 1-methyl-3-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (P13TFSI) is screened out as a particularly promising ionic liquid in this study. Dimensionally stable, elastic, flexible, nonvolatile polymer gel electrolytes (PGEs) with high electrochemical stabilities, high ionic conductivities and other desirable properties have been synthesized by dissolving Li imide salt (LiTFSI) in P13TFSI ionic liquid and then mixing the electrolyte solution with poly(vinylidene-co-hexafluoropropylene) (PVDF-HFP) copolymer. Adding small amounts of ethylene carbonate to the polymer gel electrolytes dramatically improves the ionic conductivity, net Li ion transport concentration, and Li ion transport kinetics of these electrolytes. They are thus favorable and offer good prospects in the application to rechargeable Li batteries including open systems like Li/air batteries, as well as more “conventional” rechargeable lithium and lithium ion batteries. PMID:20354587

  17. Effects of Lewis-acid polymer on the electrochemical properties of alkylphosphate-based non-flammable gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Lalia, Boor Singh; Yoshimoto, Nobuko; Egashira, Minato; Morita, Masayuki [Department of Applied Chemistry, Graduate School of Science and Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube 755-8611 (Japan)

    2009-10-20

    Non-flammable polymer gel electrolytes (NPGE) consisting of 1.0 mol dm{sup -3} (=M) LiBF{sub 4}/EC + DEC + TEP (55:25:20 volume ratio) + PVdF-HFP (EC: ethylene carbonate, DEC: diethyl carbonate, TEP: triethylphosphate, PVdF-HFP: poly(vinyledenefluoride-co-hexafluoropropylene)) have been developed for rechargeable lithium batteries. The effects of addition of Lewis-acid polymer (LAP) with different mole ratio in NPGE have been studied. The addition of LAP improved physico-chemical properties of NPGE, viz ionic conductivity and lithium ion transport number, as well as mechanical and thermal properties. The ionic conductivity of the gel electrolyte containing LAP reached that of the base solution electrolyte (1.0 M LiBF{sub 4}/EC + DEC + TEP (55:25:20)) along with better mechanical properties. Interfacial resistance at Li-metal electrode/NPGE was also improved by introducing LAP in the gel. (author)

  18. Effects of Lewis-acid polymer on the electrochemical properties of alkylphosphate-based non-flammable gel electrolyte

    Science.gov (United States)

    Lalia, Boor Singh; Yoshimoto, Nobuko; Egashira, Minato; Morita, Masayuki

    Non-flammable polymer gel electrolytes (NPGE) consisting of 1.0 mol dm -3 (=M) LiBF 4/EC + DEC + TEP (55:25:20 volume ratio) + PVdF-HFP (EC: ethylene carbonate, DEC: diethyl carbonate, TEP: triethylphosphate, PVdF-HFP: poly(vinyledenefluoride-co-hexafluoropropylene)) have been developed for rechargeable lithium batteries. The effects of addition of Lewis-acid polymer (LAP) with different mole ratio in NPGE have been studied. The addition of LAP improved physico-chemical properties of NPGE, viz ionic conductivity and lithium ion transport number, as well as mechanical and thermal properties. The ionic conductivity of the gel electrolyte containing LAP reached that of the base solution electrolyte (1.0 M LiBF 4/EC + DEC + TEP (55:25:20)) along with better mechanical properties. Interfacial resistance at Li-metal electrode/NPGE was also improved by introducing LAP in the gel.

  19. Solid-state electric double layer capacitors fabricated with plastic crystal based flexible gel polymer electrolytes: Effective role of electrolyte anions

    Energy Technology Data Exchange (ETDEWEB)

    Suleman, Mohd; Kumar, Yogesh; Hashmi, S.A., E-mail: sahashmi@physics.du.ac.in

    2015-08-01

    Flexible gel polymer electrolyte (GPE) thick films incorporated with solutions of lithium trifluoromethanesulfonate (Li-triflate or LiTf) and lithium bis trifluoromethane-sulfonimide (LiTFSI) in a plastic crystal succinonitrile (SN), entrapped in poly(vinylidine fluoride-co-hexafluoropropylene) (PVdF-HFP) have been prepared and characterized. The films have been used as electrolytes in the electrical double layer capacitors (EDLCs). Coconut-shell derived activated carbon with high specific surface area (∼2100 m{sup 2} g{sup −1}) and mixed (micro- and meso-) porosity has been used as EDLC electrodes. The structural, thermal, and electrochemical characterization of the GPEs have been performed using scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impedance measurements and cyclic voltammetry. The high ionic conductivity (∼10{sup −3} S cm{sup −1} at 25 °C), good electrochemical stability window (>4.0 V) and flexible nature of the free-standing films of GPEs show their competence in the fabrication of EDLCs. The EDLCs have been tested using electrochemical impedance spectroscopy, cyclic voltammetry, and charge–discharge studies. The EDLCs using LiTf based electrolyte have been found to give higher values of specific capacitance, specific energy, power density (240–280 F g{sup −1}, ∼39 Wh kg{sup −1} and ∼19 kW kg{sup −1}, respectively) than the EDLC cell with LiTFSI based gel electrolyte. EDLCs have been found to show stable performance for ∼10{sup 4} charge–discharge cycles. The comparative studies indicate the effective role of electrolyte anions on the capacitive performance of the solid-state EDLCs. - Graphical abstract: Display Omitted - Highlights: • Flexible EDLCs with succinonitrile based gel electrolyte membranes are reported. • Anionic size of salts in gel electrolytes plays important role on capacitive performance. • Li-triflate incorporated gel electrolyte shows better

  20. Novel configuration of poly(vinylidenedifluoride)-based gel polymer electrolyte for application in lithium-ion batteries

    Science.gov (United States)

    Fasciani, Chiara; Panero, Stefania; Hassoun, Jusef; Scrosati, Bruno

    2015-10-01

    Herein we propose a novel poly(vinylidene difluoride) (PVdF)-based gel polymer electrolyte (GPE) for application in lithium-ion batteries, LIBs. The GPE is prepared under air as a dry, flexible film and directly gelled during LIB assembly with a conventional liquid organic electrolyte. The dry-gel here originally reported maintains its structural integrity due to the presence of crystallized EC-solvent within its matrix that avoids structural collapse, as demonstrated by TGA analysis. By avoiding the use of controlled atmosphere, the GPE is easy to handle and suitable for roll-to-roll scaling-up, i.e. characteristics missed by the common gel membranes. Scanning Electron Microscopy (SEM) evidences a micrometric polymer network of the dry membrane precursor acting as the support matrix for the gelation. Electrochemical impedance spectroscopy (EIS) measurements and galvanostatic tests suggest a good stability of the lithium electrode/gel electrolyte interface and a satisfactory lithium transference number. Cycling tests of gel-electrolyte-based lithium half-cells using lithium iron phosphate (LiFePO4, LFP) and graphite (C), respectively, as counter electrodes, as well as of a full C/LFP lithium-ion battery confirm the suitability of the GPE developed in this work for application in stable, low cost and environmentally friendly energy storage systems.

  1. High efficiency dye-sensitized nanocrystalline solar cells based on ionic liquid polymer gel electrolyte.

    Science.gov (United States)

    Wang, Peng; Zakeeruddin, Shaik M; Exnar, Ivan; Grätzel, Michael

    2002-12-21

    An ionic liquid polymer gel containing 1-methyl-3-propylimidazolium iodide (MPII) and poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) has been employed as quasi-solid-state electrolyte in dye-sensitized nanocrystalline TiO2 solar cells with an overall conversion efficiency of 5.3% at AM 1.5 illumination.

  2. Laminated electrochromic windows based on nickel oxide, tungsten oxide, and gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Passerini, S.; Scrosati, B.; Hermann, V. (Univ. di Roma (Italy). Dipt. di Chimica); Holmblad, C.; Bartlett, T. (Medtronic Promeon, Minneapolis, MN (United States))

    1994-04-01

    The characteristic and the performance of solid-state, laminated electrochromic windows using tungsten oxide as the principal electrochromic electrode and nonstoichiometric nickel oxide as the counterelectrode separated by selected gel electrolytes, are presented and discussed. These advanced-design, electro-optical devices show a very promising behavior in terms of light modulation and cyclability.

  3. A novel high-performance gel polymer electrolyte membrane basing on electrospinning technique for lithium rechargeable batteries

    Science.gov (United States)

    Wu, Na; Cao, Qi; Wang, Xianyou; Li, Xiaoyun; Deng, Huayang

    2011-10-01

    Nonwoven films of composites of thermoplastic polyurethane (TPU) with different proportion of poly(vinylidene fluoride) (PVdF) (80, 50 and 20%, w/w) are prepared by electrospinning 9 wt% polymer solution at room temperature. Then the gel polymer electrolytes (GPEs) are prepared by soaking the electrospun TPU-PVdF blending membranes in 1 M LiClO4/ethylene carbonate (EC)/propylene carbonate (PC) for 1 h. The gel polymer electrolyte (GPE) shows a maximum ionic conductivity of 3.2 × 10-3 S cm-1 at room temperature and electrochemical stability up to 5.0 V versus Li+/Li for the 50:50 blend ratio of TPU:PVdF system. At the first cycle, it shows a first charge-discharge capacity of 168.9 mAh g-1 when the gel polymer electrolyte (GPE) is evaluated in a Li/PE/lithium iron phosphate (LiFePO4) cell at 0.1 C-rate at 25 °C. TPU-PVdF (50:50, w/w) based gel polymer electrolyte is observed much more suitable than the composite films with other ratios for high-performance lithium rechargeable batteries.

  4. Li Ion Conducting Polymer Gel Electrolytes Based on Ionic Liquid/PVDF-HFP Blends

    OpenAIRE

    Ye, Hui; Huang, Jian; Xu, Jun John; Khalfan, Amish; Greenbaum, Steve G.

    2007-01-01

    Ionic liquids thermodynamically compatible with Li metal are very promising for applications to rechargeable lithium batteries. 1-methyl-3-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (P13TFSI) is screened out as a particularly promising ionic liquid in this study. Dimensionally stable, elastic, flexible, nonvolatile polymer gel electrolytes (PGEs) with high electrochemical stabilities, high ionic conductivities and other desirable properties have been synthesized by dissolving Li i...

  5. Electrical and electrochemical studies on sodium ion-based gel polymer electrolytes

    Science.gov (United States)

    Isa, K. B. Md; Othman, L.; Hambali, D.; Osman, Z.

    2017-09-01

    Gel polymer electrolytes (GPEs) have captured great attention because of their unique properties such as good mechanical stability, high flexibility and high conductivity approachable to that of the liquid electrolytes. In this work, we have prepared sodium ion conducting gel polymer electrolyte (GPE) films consisting of polyvinylidenefluoride-co-hexafluoropropylene (PVdF-HFP) as a polymer host using the solution casting technique. Sodium trifluoromethane- sulfonate (NaCF3SO3) was used as an ionic salt and the mixture of ethylene carbonate (EC) and propylene carbonate (PC) as a plasticizing solvent. Impedance spectroscopy measurements were carried out to determine the ionic conductivity of the GPE films. The sample containing 20 wt.% of NaCF3SO3 salt exhibits the highest room temperature ionic conductivity of 2.50 × 10-3 S cm-1. The conductivity of the GPE films was found to depend on the salt concentration that added to the films. The ionic and cationic transference numbers of GPE films were estimated by DC polarization and the combination of AC and DC polarization method, respectively. The results had shown that both ionic and cationic transference numbers are consistent with the conductivity studies. The electrochemical stability of the GPE films was tested using linear sweep voltammetry (LSV) and the value of working voltage range appears to be high enough to be used as an electrolyte in sodium batteries. The cyclic voltammetry (CV) studies confirmed the sodium ion conduction in the GPE films.

  6. Preparation of porous, chemically cross-linked, PVdF-based gel polymer electrolytes for rechargeable lithium batteries

    Science.gov (United States)

    Cheng, C. L.; Wan, C. C.; Wang, Y. Y.

    This study reports the development of a new system of porous, chemically cross-linked, gel polymer electrolytes based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) copolymer as a polymer matrix, polyethylene glycol (PEG) as a plasticizer, and polyethylene glycol dimethacrylate (PEGDMA) as a chemical cross-linking oligomer. The electrolytes are prepared by a combination of controlled evaporation and thermal polymerization of PEGDMA. PVdF-HFP/PEG/PEGDMA gel polymer electrolytes with a composition of 5/3/2 exhibit both high ambient ionic conductivity, viz., >1 mS cm -1, and a high tensile modulus of 52 MPa, because of their porous and network structures. All the blends of electrolytes are electrochemically stable up to 5 V versus Li/Li + in the presence of 1 M LiPF 6/ethylene carbonate-diethyl carbonate (EC-DEC). With these polymer electrolytes, rechargeable lithium batteries composed of carbon anode and LiCoO 2 cathode have acceptable cycleability and a good rate capability.

  7. Ionic conductivity and battery characteristic studies of a new PAN-based Na+ ion conducting gel polymer electrolyte system

    Science.gov (United States)

    Krishna Jyothi, N.; Vijaya Kumar, K.; Sunita Sundari, G.; Narayana Murthy, P.

    2016-03-01

    Sodium ion conducting gel polymer electrolytes based on polyacrylonitrile (PAN) with ethylene carbonate and dimethyl formamide as plasticizing solvents are prepared by the solution cast technique. These electrolyte films are free standing, transparent and dimensionally stable. Na+ ions are derived from NaI. The structural properties of pure and complex formations have been examined by X-ray diffraction, Fourier transform infrared spectroscopic studies and differential scanning calorimetric studies. The variation of the conductivity with salt concentration ranging from 10 to 40 wt% is studied. The sample containing 30 wt% of NaI exhibits the highest conductivity of 2.35 × 10-4 S cm-1 at room temperature (303 K) and 1 × 10-3 S cm-1 at 373 K. The conductivity-temperature dependence of polymer electrolyte films obeys Arrhenius behavior with activation energy in the range of 0.25-0.46 eV. The transport numbers both electronic ( t e) and ionic ( t i) are evaluated using Wagner's polarization technique. It is revealed that the conducting species are predominantly due to ions. The ionic transport number of highest conducting film is found to be 0.991. Solid-state battery with configuration Na/(PAN + NaI)/(I2 + C + electrolyte) is developed using the highest conducting gel polymer electrolyte system and the discharge characteristics of the cell are evaluated over the load of 100 KΩ.

  8. Natural macromolecule based carboxymethyl cellulose as a gel polymer electrolyte with adjustable porosity for lithium ion batteries

    Science.gov (United States)

    Zhu, Y. S.; Xiao, S. Y.; Li, M. X.; Chang, Z.; Wang, F. X.; Gao, J.; Wu, Y. P.

    2015-08-01

    A porous membrane of carboxymethyl cellulose (CMC) from natural macromolecule as a host of a gel polymer electrolyte for lithium ion batteries is reported. It is prepared, for the first time, by a simple non-solvent evaporation method and its porous structure is fine-adjusted by varying the composition ratio of the solvent and non-solvent mixture. The electrolyte uptake of the porous membrane based on CMC is 75.9%. The ionic conductivity of the as-prepared gel membrane saturated with 1 mol L-1 LiPF6 electrolyte at room temperature can be up to 0.48 mS cm-1. Moreover, the lithium ion transference in the gel membrane at room temperature is as high as 0.46, much higher than 0.27 for the commercial separator Celgard 2730. When evaluated by using LiFePO4 cathode, the prepared gel membrane exhibits very good electrochemical performance including higher reversible capacity, better rate capability and good cycling behaviour. The obtained results suggest that this porous polymer membrane shows great attraction to the lithium ion batteries requiring high safety, low cost and environmental friendliness.

  9. Studies on gel electrolyte based on nitrile-butadiene copolymers. Final report, 1 November 1991-30 November 1992

    Energy Technology Data Exchange (ETDEWEB)

    Sircar, A.K.; Kumar, B.; Linden, S.M.; Weissman, P.T.

    1993-06-01

    This study is concerned with the preparation of a hybrid electrolyte, suitable for solid-polymer batteries. Based on the study of ionic conductivity in the presence of LiBF4 of a number of nitrile-butadiene copolymers (NBR), hydrogenated NBR (HNBR) was selected as the host polymer. DC conductivity studies with three different lithium salts in different plasticizers showed the highest conductivity for LiBF4. Conductivity of LiBF4 in different plasticizers decreases in the order DMF > DMAC > Gamma butyrolactone > NMP > PC=gamma-valerolactone > glymes. NMP was chosen as the plasticizer for hybrid films based on its moderate conductivity, low vapor pressure, and low freezing point. Polymer electrolytes, Gel electrolytes, Ionic conductivity.

  10. A supramolecular gel electrolyte formed from amide based co-gelator for quasi-solid-state dye-sensitized solar cell with boosted electron kinetic processes

    Science.gov (United States)

    Huo, Zhipeng; Wang, Lu; Tao, Li; Ding, Yong; Yi, Jinxin; Alsaedi, Ahmed; Hayat, Tasawar; Dai, Songyuan

    2017-08-01

    A supramolecular gel electrolyte (Tgel > 100 °C) is formed from N,N‧-1,8-octanediylbis-dodecanamide and iodoacetamide as two-component co-gelator, and introduced into the quasi-solid-state dye-sensitized solar cells (QS-DSSCs). The different morphologies of microscopic network between two-component and single-component gel electrolytes have influence on the diffusion of redox couple in gel electrolytes and further affect the electron kinetic processes in QS-DSSCs. Compared with the single-component gel electrolyte, the two-component gel electrolyte has less compact gel network and weaker steric hindrance effect, which provides more effective charge transport channel for the diffusion of I3/I- redox couple. Meanwhile, the sbnd NH2 groups of iodoacetamide molecules interact with Li+ and I3-, which also accelerate the transport of I3-/I- and decrease in the I3- concentration in the TiO2/electrolyte interface. As a result, nearly a 12% improvement in short-circuit photocurrent density (Jsc) and much higher open circuit potential (Voc) are found in the two-component gel electrolyte based QS-DSSC. Consequently, the QS-DSSC based on the supramolecular gel electrolyte obtains a 17% enhancement in the photoelectric conversion efficiency (7.32%) in comparison with the QS-DSSC based on the single-component gel electrolyte (6.24%). Furthermore, the degradations of these QS-DSSCs are negligible after one sun light soaking with UV cutoff filter at 50 °C for 1000 h.

  11. Artificial Neural Network and Response Surface Methodology Modeling in Ionic Conductivity Predictions of Phthaloylchitosan-Based Gel Polymer Electrolyte

    Directory of Open Access Journals (Sweden)

    Ahmad Danial Azzahari

    2016-01-01

    Full Text Available A gel polymer electrolyte system based on phthaloylchitosan was prepared. The effects of process variables, such as lithium iodide, caesium iodide, and 1-butyl-3-methylimidazolium iodide were investigated using a distance-based ternary mixture experimental design. A comparative approach was made between response surface methodology (RSM and artificial neural network (ANN to predict the ionic conductivity. The predictive capabilities of the two methodologies were compared in terms of coefficient of determination R2 based on the validation data set. It was shown that the developed ANN model had better predictive outcome as compared to the RSM model.

  12. Low molecular mass organogelator based gel electrolyte with effective charge transport property for long-term stable quasi-solid-state dye-sensitized solar cells.

    Science.gov (United States)

    Huo, Zhipeng; Dai, Songyuan; Zhang, Changneng; Kong, Fantai; Fang, Xiaqin; Guo, Lei; Liu, Weiqing; Hu, Linhua; Pan, Xu; Wang, Kongjia

    2008-10-16

    Stable quasi-solid-state dye-sensitized solar cells (DSC) were fabricated using 12-hydroxystearic acid as a low molecular mass organogelator (LMOG) to form gel electrolyte. TEM image of the gel exhibited the self-assembled network constructed by the LMOG, which hindered flow and volatilization of the liquid. The formation of less-mobile polyiodide ions such as I 3 (-) and I 5 (-) confirmed by Raman spectroscopy increased the conductivity of the gel electrolytes by electronic conduction process, which should be rationalized by the Grotthuss-type electron exchange mechanism caused by rather packed polyiodide species in the electrolytes. The results of the accelerated aging tests showed that the gel electrolyte based dye-sensitized solar cell could retain over 97% of its initial photoelectric conversion efficiency value after successive heating at 60 degrees C for 1000 h and device degradation was also negligible after one sun light soaking with UV cutoff filter for 1000 h.

  13. Ionic transport and electrochemical stability of PVDF-HFP based gel polymer electrolytes

    Science.gov (United States)

    Rosdi, A.; Zainol, N. H.; Osman, Z.

    2016-02-01

    The gel polymer electrolytes (GPEs) samples consisting of polyvinylidenefluoride-co-hexafluoropropylene (PVDF-HFP), ethylene carbonate (EC) and propylene carbonate (PC) with different concentrations of magnesium triflate salt, Mg(CF3SO3)2 were prepared using the solution casting technique. The ionic conductivity of the GPEs was studied by using a.c impedance spectroscopy and the sample containing 20 wt% salt exhibited the highest conductivity of 5.11 × l0-3 Scm-1. Ionic transport number of the GPEs shows that the samples contain ionic species as main charge carrier while cationic transport number for the highest conducting sample was found to be 0.27. The electrochemical properties of the GPEs were studied using Linear Sweep Voltammetry (LSV) and Cyclic Voltammetry (CV). The GPEs show high electrochemical stability ˜3.5V (versus Mg2+/Mg) where the highest conducting sample exhibited the highest stability.

  14. A composite membrane based on a biocompatible cellulose as a host of gel polymer electrolyte for lithium ion batteries

    Science.gov (United States)

    Xiao, S. Y.; Yang, Y. Q.; Li, M. X.; Wang, F. X.; Chang, Z.; Wu, Y. P.; Liu, X.

    2014-12-01

    A composite polymer membrane is prepared by coating poly(vinylidene fluoride) (PVDF) on the surface of a membrane based on methyl cellulose (MC) which is environmentally friendly and cheap. Its characteristics are investigated by scanning electron microscopy, FT-IR, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The outer PVDF layers are porous which results in high electrolyte uptake and the lithium ion transference number is much larger than that of the pure MC. Moreover, the cell based on Li//LiFePO4 delivers high discharge capacity and good rate behavior in the range of 4.2-2.5 V when the composite membrane is used as the separator and the host of a gel polymer electrolyte, lithium as the counter and reference electrode, and LiFePO4 as cathode. The obtained results suggest that this unique composite membrane shows great attraction in the lithium ion batteries with high safety and low cost.

  15. Preparation and characterization of core-shell electrodes for application in gel electrolyte-based dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Avellaneda, Cesar O.; Goncalves, Agnaldo D.; Benedetti, Joao E. [Laboratorio de Nanotecnologia e Energia Solar (LNES), Instituto de Quimica, Universidade Estadual de Campinas - UNICAMP, P.O. Box 6154, 13083-970 Campinas/SP (Brazil); Nogueira, Ana F., E-mail: anaflavia@iqm.unicamp.b [Laboratorio de Nanotecnologia e Energia Solar (LNES), Instituto de Quimica, Universidade Estadual de Campinas - UNICAMP, P.O. Box 6154, 13083-970 Campinas/SP (Brazil)

    2010-01-25

    Core-shell electrodes based on TiO{sub 2} covered with different oxides were prepared and characterized. These electrodes were applied in gel electrolyte-based dye-sensitized solar cells (DSSC). The TiO{sub 2} electrodes were prepared from TiO{sub 2} powder (P25 Degussa) and coated with thin layers of Al{sub 2}O{sub 3}, MgO, Nb{sub 2}O{sub 5}, and SrTiO{sub 3} prepared by the sol-gel method. The core-shell electrodes were characterized by X-ray diffraction, scanning electron microscopy and atomic force microscopy measurements. J-V curves in the dark and under standard AM 1.5 conditions and photovoltage decay measurements under open-circuit conditions were carried out in order to evaluate the influence of the oxide layer on the charge recombination dynamics and on the device's performance. The results indicated an improvement in the conversion efficiency as a result of an increase in the open circuit voltage. The photovoltage decay curves under open-circuit conditions showed that the core-shell electrodes provide longer electron lifetime values compared to uncoated TiO{sub 2} electrodes, corroborating with a minimization in the recombination losses at the nanoparticle surface/electrolyte interface. This is the first time that a study has been applied to DSSC based on gel polymer electrolyte. The optimum performance was achieved by solar cells based on TiO{sub 2}/MgO core-shell electrodes: fill factor of approx0.60, short-circuit current density J{sub sc} of 12 mA cm{sup -2}, open-circuit voltage V{sub oc} of 0.78 V and overall energy conversion efficiency of approx5% (under illumination of 100 mW cm{sup -2}).

  16. Microporous gel electrolytes based on amphiphilic poly(vinylidene fluoride-co-hexafluoropropylene) for lithium batteries

    Science.gov (United States)

    Yu, Shicheng; Chen, Lie; Chen, Yiwang; Tong, Yongfen

    2012-03-01

    Poly(vinylidene fluoride-co-hexafluoropropylene) grafted poly(poly(ethylene glycol) methyl ether methacrylate) (PVDF-HFP-g-PPEGMA) is simply prepared by single-step synthesis directly via atom transfer radical polymerization (ATRP) of poly(ethylene glycol) methyl ether methacrylate (PEGMA) from poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes, are evaluated and the effects of the various contents and average molecular weights of PEGMA on those properties are also been investigated. By phase inversion technique, the copolymer membranes tend to form well-defined microporous morphology with the increase of content and average molecular weight of PEGMA, due to the competition and cooperation between the hydrophilic PEGMA segments and hydrophobic PVDF-HFP. When these membranes are gelled with 1 M LiCF3SO3 in ethylene carbonate (EC)/propylene carbonate (PC) (1:1, v/v), their saturated electrolyte uptakes (up to 323.5%) and ion conductivities (up to 2.01 × 10-3 S cm-1) are dramatically improved with respect to the pristine PVDF-HFP, ascribing to the strong affinity of the hydrophilic PEGMA segments with the electrolytes. All the polymer electrolytes are electrochemically stable up to 4.7 V versus Li/Li+, and show good mechanical properties. Coin cells based on the polymer electrolytes show stable charge-discharge cycles and deliver discharge capacities to LiFePO4 is up to 156 mAh g-1.

  17. Microporous gel electrolytes based on amphiphilic poly(vinylidene fluoride-co-hexafluoropropylene) for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Yu Shicheng [Institute of Polymers, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Chen Lie, E-mail: chenlienc@163.com [Institute of Polymers, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China) and Jiangxi Provincial Key Laboratory of New Energy Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Chen Yiwang, E-mail: ywchen@ncu.edu.cn [Institute of Polymers, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Jiangxi Provincial Key Laboratory of New Energy Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Tong Yongfen [Institute of Polymers, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); School of Environmental and Chemical Engineering, Nanchang Hangkong University, 696 Fenghe South Avenue, Nanchang 330063 (China)

    2012-03-15

    Poly(vinylidene fluoride-co-hexafluoropropylene) grafted poly(poly(ethylene glycol) methyl ether methacrylate) (PVDF-HFP-g-PPEGMA) is simply prepared by single-step synthesis directly via atom transfer radical polymerization (ATRP) of poly(ethylene glycol) methyl ether methacrylate (PEGMA) from poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes, are evaluated and the effects of the various contents and average molecular weights of PEGMA on those properties are also been investigated. By phase inversion technique, the copolymer membranes tend to form well-defined microporous morphology with the increase of content and average molecular weight of PEGMA, due to the competition and cooperation between the hydrophilic PEGMA segments and hydrophobic PVDF-HFP. When these membranes are gelled with 1 M LiCF{sub 3}SO{sub 3} in ethylene carbonate (EC)/propylene carbonate (PC) (1:1, v/v), their saturated electrolyte uptakes (up to 323.5%) and ion conductivities (up to 2.01 Multiplication-Sign 10{sup -3} S cm{sup -1}) are dramatically improved with respect to the pristine PVDF-HFP, ascribing to the strong affinity of the hydrophilic PEGMA segments with the electrolytes. All the polymer electrolytes are electrochemically stable up to 4.7 V versus Li/Li{sup +}, and show good mechanical properties. Coin cells based on the polymer electrolytes show stable charge-discharge cycles and deliver discharge capacities to LiFePO{sub 4} is up to 156 mAh g{sup -1}.

  18. Hydroxypropyl Cellulose Based Non-Volatile Gel Polymer Electrolytes for Dye-Sensitized Solar Cell Applications using 1-methyl-3-propylimidazolium iodide ionic liquid

    Science.gov (United States)

    Khanmirzaei, Mohammad Hassan; Ramesh, S.; Ramesh, K.

    2015-12-01

    Gel polymer electrolytes using imidazolium based ionic liquids have attracted much attention in dye-sensitized solar cell applications. Hydroxypropyl cellulose (HPC), sodium iodide (NaI), 1-methyl-3-propylimidazolium iodide (MPII) as ionic liquid (IL), ethylene carbonate (EC) and propylene carbonate (PC) are used for preparation of non-volatile gel polymer electrolyte (GPE) system (HPC:EC:PC:NaI:MPII) for dye-sensitized solar cell (DSSC) applications. The highest ionic conductivity of 7.37 × 10-3 S cm-1 is achieved after introducing 100% of MPII with respect to the weight of HPC. Temperature-dependent ionic conductivity of gel polymer electrolytes is studied in this work. XRD patterns of gel polymer electrolytes are studied to confirm complexation between HPC polymer, NaI and MPII. Thermal behavior of the GPEs is studied using simultaneous thermal analyzer (STA) and differential scanning calorimetry (DSC). DSSCs are fabricated using gel polymer electrolytes and J-V centeracteristics of fabricated dye sensitized solar cells were analyzed. The gel polymer electrolyte with 100 wt.% of MPII ionic liquid shows the best performance and energy conversion efficiency of 5.79%, with short-circuit current density, open-circuit voltage and fill factor of 13.73 mA cm-2, 610 mV and 69.1%, respectively.

  19. Hydroxypropyl Cellulose Based Non-Volatile Gel Polymer Electrolytes for Dye-Sensitized Solar Cell Applications using 1-methyl-3-propylimidazolium iodide ionic liquid.

    Science.gov (United States)

    Khanmirzaei, Mohammad Hassan; Ramesh, S; Ramesh, K

    2015-12-11

    Gel polymer electrolytes using imidazolium based ionic liquids have attracted much attention in dye-sensitized solar cell applications. Hydroxypropyl cellulose (HPC), sodium iodide (NaI), 1-methyl-3-propylimidazolium iodide (MPII) as ionic liquid (IL), ethylene carbonate (EC) and propylene carbonate (PC) are used for preparation of non-volatile gel polymer electrolyte (GPE) system (HPC:EC:PC:NaI:MPII) for dye-sensitized solar cell (DSSC) applications. The highest ionic conductivity of 7.37 × 10(-3) S cm(-1) is achieved after introducing 100% of MPII with respect to the weight of HPC. Temperature-dependent ionic conductivity of gel polymer electrolytes is studied in this work. XRD patterns of gel polymer electrolytes are studied to confirm complexation between HPC polymer, NaI and MPII. Thermal behavior of the GPEs is studied using simultaneous thermal analyzer (STA) and differential scanning calorimetry (DSC). DSSCs are fabricated using gel polymer electrolytes and J-V centeracteristics of fabricated dye sensitized solar cells were analyzed. The gel polymer electrolyte with 100 wt.% of MPII ionic liquid shows the best performance and energy conversion efficiency of 5.79%, with short-circuit current density, open-circuit voltage and fill factor of 13.73 mA cm(-2), 610 mV and 69.1%, respectively.

  20. Quasi-solid state dye-sensitized solar cells based on pyridine or imidazole containing copolymer chemically crosslinked gel electrolytes

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Quasi-solid state dye-sensitized solar cells based on chemically crosslinking with backbone polymers of poly(vinylpyridine-co-acrylonitrile) (P(VP-co-AN)) or poly(vinylimidazole-co-acrylonitrile) (P(VIM-co- AN)) and diiodide compounds of I(CH2)6I or I(CH2CH2O)nCH2CH2I solidified EC/PC/KI/I2 gel electrolytes have been fabricated. The ionic conductivities and apparent diffusion coefficients of I3-Of the electrolytes and cell performances have been investigated. Providing chemically crosslinking points, pyridine or imidazole from the backbone polymers benefited the open circuit voltage and fill factor of the cells. Consequently, the overall energy conversion efficiencies of the quasi-solid DSSCs improved over 10% even near 20% from that of the liquid electrolyte before solidification. Besides, the employing of crosslinker I(CH2CH2O)nCH2CH2I showed higher electrolytic and cell characters than that of I(CH2)6I.

  1. Quasi-solid-state nanocrystalline TiO2 solar cells using gel network polymer electrolytes based on polysiloxanes

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A quasi-solid-state dye-sensitized nanocrystalline porous TiO2 film solar cell was fabricated using a novel gel network polymer electrolyte based on polysiloxanes with both polyethylene oxide internal plasticized side chains and quaternary ammonium groups. The cell exhibited better photoelectrical conversion performance under 60 mW/cm2 irradiation. The short photocurrent (Isc) of 5.0 mA/cm2 and open voltage (Voc) of 0.68 V were achieved, and the energy conversion efficiency (η) and fill factor (ff) were 3.4% and 0.60, respectively.

  2. The charge transport in polymeric gel electrolytes

    CERN Document Server

    Reiche, A

    2001-01-01

    The aim of the present thesis consisted in the study of the charge transport in gel electrolytes, which were obtained by photopolymerization of oligo(ethylene glycol) sub n -dimethacrylates with n=3, 9, and 23, and the survey of structure and property relations for the optimization of the electrolyte composition. The pressure dependence of the electric conductivity was measured. (HSI)

  3. 3-V Solid-State Flexible Supercapacitors with Ionic-Liquid-Based Polymer Gel Electrolyte for AC Line Filtering.

    Science.gov (United States)

    Kang, Yu Jin; Yoo, Yongju; Kim, Woong

    2016-06-08

    State-of-the-art solid-state flexible supercapacitors with sufficiently fast response speed for AC line filtering application suffer from limited energy density. One of the main causes of the low energy density is the low cell voltage (1 V), which is limited by aqueous-solution-based gel electrolytes. In this work, we demonstrate for the first time a 3-V flexible supercapacitor for AC line filtering based on an ionic-liquid-based polymer gel electrolyte and carbon nanotube electrode material. The flexible supercapacitor exhibits an areal energy density that is more than 20 times higher than that of the previously demonstrated 1-V flexible supercapacitor (0.66 vs 0.03 μWh/cm(2)) while maintaining excellent capacitive behavior at 120 Hz. The supercapacitor shows a maximum areal power density of 1.5 W/cm(2) and a time constant of 1 ms. The improvement of the cell voltage while maintaining the fast-response capability greatly improves the potential of supercapacitors for high-frequency applications in wearable and/or portable electronics.

  4. Effect of poly(ethylene oxide) on ionic conductivity and electrochemical properties of poly(vinylidenefluoride) based polymer gel electrolytes prepared by electrospinning for lithium ion batteries

    Science.gov (United States)

    Prasanth, Raghavan; Shubha, Nageswaran; Hng, Huey Hoon; Srinivasan, Madhavi

    2014-01-01

    Effect of poly(ethylene oxide) on the electrochemical properties of polymer electrolyte based on electrospun, non-woven membrane of PVdF is demonstrated. Electrospinning process parameters are controlled to get a fibrous membrane consisting of bead-free, uniformly dispersed thin fibers with diameter in the range of 1.5-1.9 μm. The membrane with good mechanical strength and porosity exhibits high uptake when activated with the liquid electrolyte of lithium salt in a mixture of organic solvents. The polymer gel electrolyte shows ionic conductivity of 4.9 × 10-3 S cm-1 at room temperature. Electrochemical performance of the polymer gel electrolyte is evaluated in Li/polymer electrolyte/LiFePO4 coin cell. Good performance with low capacity fading on charge-discharge cycling is demonstrated.

  5. A comparative study of gel polymer electrolytes based on PVDF-HFP and liquid electrolytes, containing imidazolinium ionic liquids of different carbon chain lengths in DSSCs

    Energy Technology Data Exchange (ETDEWEB)

    Suryanarayanan, Vembu [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Lee, Kun-Mu [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China); Ho, Wen-Hsien; Chen, Hung-Chang [Department of Product Development, Taiwan Textile Research Institute, Tucheng 23674 (China); Ho, Kuo-Chuan [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China)

    2007-09-22

    The photoelectrochemical characteristics of titanium dioxide (TiO{sub 2})-based dye-sensitized solar cells (DSSCs) containing gel polymer electrolyte (GPE) and organic liquid electrolyte (OLE) were studied in detail. GPE was prepared by adding poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP) to imidazolinium ionic liquids (IILs) of the type, 1-methyl-3-alkyl imidazolinium iodides (alkyl is C{sub n}H{sub 2n+1}, where n=3-10) in methoxy propionitrile (MPN) and the OLE contained the above molten salt in MPN. The IILs were synthesized in the laboratory and characterized by {sup 1}H nuclear magnetic resonance spectroscopy (NMR). The conductivities ({sigma}) of both GPE and OLE decrease with increase in chain length (n) of the alkyl group of IILs; however, the effect is more drastic in the former case. The performance of the DSSCs containing OLE increases with the increase in alkyl chain length of IIL from C3 to C7, whereas, there is a linear decrease in the efficiency of the DSSCs incorporated with GPE containing IIL of alkyl chain length from C3 to C10. The change in short circuit current density (J{sub SC}) determines the cell efficiency as the V{sub OC} of the DSSCs remains almost the same with increase of alkyl chain length of IILs for both the electrolytes. The change in J{sub SC} values and the consistency of the V{sub OC} of the DSSCs for both the electrolytes may be explained on the basis of increase in viscosity of IILs from C3 to C10 and the dominating role of the 4-tertiary butyl pyridine (TBP), respectively, on the phenomenon of charge recombination. (author)

  6. Ionic liquid-polymer gel electrolytes based on morpholinium salt and PVdF(HFP) copolymer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki-Sub; Park, Seung-Yeob; Choi, Sukjeong; Lee, Huen [Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)

    2006-04-21

    New ionic liquid-polymer gel electrolytes (IPGEs) are prepared from N-ethyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide (Mor{sub 1,2}TFSI) and poly(vinylidene fluoride)-hexafluoropropylene copolymer (PVdF(HFP)). To investigate the effect of propylene carbonate (PC) on the ionic conductivity of the IPGEs, the preparation methods are roughly divided into two groups according to the presence or absence of PC. The ionic conductivity for each IPGE is measured with increasing temperature and changing weight ratio of Mor{sub 1,2}TFSI. The results show that the ionic conductivity increases as the temperature and weight ratio of the Mor{sub 1,2}TFSI increase, and that the added PC improves the ionic conductivity of the IPGEs. In addition, thermogravimetric analysis and the data from infrared spectroscopy demonstrate the thermal stability of each IPGE and the presence of PC in the polymer network. Although the IPGEs that contain PC display high conductivity ({approx}1.1x10{sup -2}Scm{sup -1}) at 60{sup o}C, they are thermally unstable. (author)

  7. A zwitterionic gel electrolyte for efficient solid-state supercapacitors.

    Science.gov (United States)

    Peng, Xu; Liu, Huili; Yin, Qin; Wu, Junchi; Chen, Pengzuo; Zhang, Guangzhao; Liu, Guangming; Wu, Changzheng; Xie, Yi

    2016-05-26

    Gel electrolytes have attracted increasing attention for solid-state supercapacitors. An ideal gel electrolyte usually requires a combination of advantages of high ion migration rate, reasonable mechanical strength and robust water retention ability at the solid state for ensuring excellent work durability. Here we report a zwitterionic gel electrolyte that successfully brings the synergic advantages of robust water retention ability and ion migration channels, manifesting in superior electrochemical performance. When applying the zwitterionic gel electrolyte, our graphene-based solid-state supercapacitor reaches a volume capacitance of 300.8 F cm(-3) at 0.8 A cm(-3) with a rate capacity of only 14.9% capacitance loss as the current density increases from 0.8 to 20 A cm(-3), representing the best value among the previously reported graphene-based solid-state supercapacitors, to the best of our knowledge. We anticipate that zwitterionic gel electrolyte may be developed as a gel electrolyte in solid-state supercapacitors.

  8. A zwitterionic gel electrolyte for efficient solid-state supercapacitors

    Science.gov (United States)

    Peng, Xu; Liu, Huili; Yin, Qin; Wu, Junchi; Chen, Pengzuo; Zhang, Guangzhao; Liu, Guangming; Wu, Changzheng; Xie, Yi

    2016-05-01

    Gel electrolytes have attracted increasing attention for solid-state supercapacitors. An ideal gel electrolyte usually requires a combination of advantages of high ion migration rate, reasonable mechanical strength and robust water retention ability at the solid state for ensuring excellent work durability. Here we report a zwitterionic gel electrolyte that successfully brings the synergic advantages of robust water retention ability and ion migration channels, manifesting in superior electrochemical performance. When applying the zwitterionic gel electrolyte, our graphene-based solid-state supercapacitor reaches a volume capacitance of 300.8 F cm-3 at 0.8 A cm-3 with a rate capacity of only 14.9% capacitance loss as the current density increases from 0.8 to 20 A cm-3, representing the best value among the previously reported graphene-based solid-state supercapacitors, to the best of our knowledge. We anticipate that zwitterionic gel electrolyte may be developed as a gel electrolyte in solid-state supercapacitors.

  9. Ionogel Electrolytes through Sol-Gel Processing

    Science.gov (United States)

    Horowitz, Ariel I.

    Electrical energy needs have intensified due to the ubiquity of personal electronics, the decarbonization of energy services through electrification, and the use of intermittent renewable energy sources. Despite developments in mechanical and thermal methods, electrochemical technologies are the most convenient and effective means of storing electrical energy. These technologies include both electrochemical cells, commonly called batteries, and electrochemical double-layer capacitors, or "supercapacitors", which store energy electrostatically. Both device types require an ion-conducting electrolyte. Current devices use solutions of complex salts in organic solvents, leading to both toxicity and flammability concerns. These drawbacks can be avoided by replacing conventional electrolytes with room-temperature molten salts, known as ionic liquids (ILs). ILs are non-volatile, non-flammable, and offer high conductivity and good electrochemical stability. Device mass can be reduced by combining ILs with a solid scaffold material to form an "ionogel," further improving performance metrics. In this work, sol-gel chemistry is explored as a means of forming ionogel electrolytes. Sol-gel chemistry is a solution-based, industrially-relevant, well-studied technique by which solids such as silica can be formed in situ. Previous works used a simple acid-catalyzed sol-gel reaction to create brittle, glassy ionogels. Here, both the range of products that can be accomplished through sol-gel processing and the understanding of interactions between ILs and the sol-gel reaction network are greatly expanded. This work introduces novel ionogel materials, including soft and compliant silica-supported ionogels and PDMS-supported ionogels. The impacts of the reactive formulation, IL identity, and casting time are detailed. It is demonstrated that variations in formulation can lead to rapid gelation and open pore structures in the silica scaffold or slow gelation and more dense silica

  10. Electrochemical characterization of poly(ethylene-co-methyl acrylate)-based gel polymer electrolytes for lithim-ion polymer batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Won [Samsung Advanced Inst. of Technology, Daejon (Korea). Electrochemistry Lab.

    2000-04-01

    Gel polymer electrolytes (GPE) composed of poly(ethylene-co-methyl acrylate) copolymer, LiBF{sub 4}-EC/EMC/PC, and silanized fumed silica are prepared. The ionic conductivity reaches 5.8x10{sup -4} S cm{sup -1} in the GPE containing 22% poly(ethylene-co-methyl acrylate), 65% LiBF{sub 4}-EC/EMC/PC and 13% silanized fumed silica at room temperature. GPEs are free-standing films and are used to prepare thin films for rechargeable lithium-ion polymer cells. Lithium-ion polymer cells, which consist of mesophase carbon fibre anode, poly(ethylene-co-methyl acrylate)-based GPE and LiCoO{sub 2} cathode, are assembled, and their charge-discharge cycling characteristics are investigated. (orig.)

  11. Gel polymer electrolyte based on LiBOB and PAN for the application in dye-sensitized solar cells

    Science.gov (United States)

    Arof, A. K.; Jun, H. K.; Sim, L. N.; Kufian, M. Z.; Sahraoui, B.

    2013-11-01

    Dye-sensitized solar cells (DSSCs) have been fabricated using metal complex N3 dye coupled with LiBOB and PAN-based gel polymer electrolyte (GPE). Conductivity of the GPE at room temperature was 1.2 × 10-2 S cm-1. The deconvoluted vibration spectra at different temperatures between 1000 and 970 cm-1 show the existence of ion pairs and free ions. Overall efficiency and fill factor of the DSSC with LiBOB-BMII-PAN-I2 GPE system is 0.65% and 48% respectively. The cell with LiBOB-BMII-PAN-I2 GPE system appears to be stable under varied light intensity attributed to the presence of redox couple mediator in the GPE. Impedance measurements show that the DSSC with LiBOB-BMII-PAN-I2 GPE has longer electron lifetime which suggests a lower electron recombination rate.

  12. Alkylphosphate-based nonflammable gel electrolyte for LiMn 2O 4 positive electrode in lithium-ion battery

    Science.gov (United States)

    Yoshimoto, Nobuko; Gotoh, Daisuke; Egashira, Minato; Morita, Masayuki

    Polymeric gel containing alkylphosphate has been examined as nonflammable gel electrolyte for LiMn 2O 4 positive electrode of lithium-ion battery (LIB). The gel was composed of a polymer matrix of poly(vinylidenefluoride- co-hexafluoropropylene) (PVdF-HFP) and a liquid component consisting of ternary solvent of trimethyl phosphate (TMP) mixed with ethylene carbonate (EC) and diethyl carbonate (DEC) that dissolves lithium salt (LiPF 6 or LiBF 4). The gel composition of 0.8 M (mol dm -3) LiX (X = PF 6 and BF 4) dissolved in EC + DEC + TMP (55:25:20) with PVdF-HFP showed excellent nonflammable characteristics and high ionic conductivity of ca. 3.1 mS cm -1 at room temperature (20 °C). The charge-discharge cycling test of LiMn 2O 4 positive electrode gave good reversibility with high capacitance in the gel electrolyte. With respect to the electrolyte salt, LiBF 4 was better than LiPF 6 due to its thermal stability during the gel preparation.

  13. Electrochemical performance of nonflammable polymeric gel electrolyte containing triethylphosphate

    Energy Technology Data Exchange (ETDEWEB)

    Lalia, Boor Singh; Fujita, Takayoshi; Yoshimoto, Nobuko; Egashira, Minato; Morita, Masayuki [Graduate School of Science and Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube 755-8611 (Japan)

    2009-01-01

    Nonflammable polymeric gel electrolyte has been prepared by immobilizing 1 M LiBF{sub 4}/EC + DEC + TEP (55:25:20, v/v/v, EC: ethylene carbonate, DEC: diethyl carbonate and TEP: triethylphosphate) solution in poly(vinylidene fluoride-co-hexafluoro propylene) (PVdF-HFP) where TEP acts as a fire-retardant solvent in the gel electrolyte. The polymeric gel electrolyte has a high value of ionic conductivity of 1.76 mS cm{sup -1} at 28 C. Thermal safety calorimetry (TSC) experiments show good thermal stability of the gel electrolyte. Cyclic voltammetry and charge/discharge cycling tests were performed on LiMn{sub 2}O{sub 4}/gel electrolyte and graphite/gel electrolyte half cells. The gel electrolyte works well for graphite/LiMn{sub 2}O{sub 4} cell although some improvement in the cycleability of the graphite electrode is still needed. (author)

  14. Hexanoyl Chitosan-based Gel Electrolyte for Lithium-ion Cell

    Institute of Scientific and Technical Information of China (English)

    Tan Winie; A.K. Arof

    2005-01-01

    @@ 1Introduction Chitosan is soluble in dilute acid solutions as a result of salt formation by the amino groups with various inorganic and organic acids[1,2]. Due to the reactivity of water and other protic solvents such as methanol and acetic acid with the electrode material in the lithiumbased electrochemicaldevices[3], the insolubility of chitosan in aprotic solvents is inadequate to meet the requirements to be used as the electrolyte materials. In order to improve its solubility in aprotic solvents,acyl modification of chitosan was carried out in the present study.Hexanoyl-chitosan (Fig. 1) that exhibited solubility in THF was prepared by reacting the chitosan with hexanoyl chloride in a mixture of pyridine and THF[4].

  15. Dual phase polymer gel electrolyte based on non-woven poly(vinylidenefluoride-co-hexafluoropropylene)–layered clay nanocomposite fibrous membranes for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Shubha, Nageswaran [School of Materials Science and Engineering, Nanyang Technological University, Block N4.1, 50 Nanyang Avenue, Singapore 639798 (Singapore); Prasanth, Raghavan [School of Materials Science and Engineering, Nanyang Technological University, Block N4.1, 50 Nanyang Avenue, Singapore 639798 (Singapore); Energy Research Institute - NTU (ERI-N) Research Techno Plaza, 50 Nanyang Drive, Singapore 637553 (Singapore); TUM-CREATE Center for Electromobility, Nanyang Technological University, Singapore 637553 (Singapore); Hoon, Hng Huey [School of Materials Science and Engineering, Nanyang Technological University, Block N4.1, 50 Nanyang Avenue, Singapore 639798 (Singapore); Srinivasan, Madhavi, E-mail: madhavi@ntu.edu.sg [School of Materials Science and Engineering, Nanyang Technological University, Block N4.1, 50 Nanyang Avenue, Singapore 639798 (Singapore); Energy Research Institute - NTU (ERI-N) Research Techno Plaza, 50 Nanyang Drive, Singapore 637553 (Singapore); TUM-CREATE Center for Electromobility, Nanyang Technological University, Singapore 637553 (Singapore)

    2013-02-15

    Graphical abstract: Display Omitted Highlights: ► P(VdF-co-HFP)–clay nanocomposite based electrospun membranes are prepared. ► The membranes are used as polymer gel electrolyte (PGE) in lithium ion batteries. ► The composite PGE shows ionic conductivity of 5.5 mS cm{sup −1} at room temperature. ► Li/PGE/LiFePO{sub 4} cell delivers initial discharge capacity of 160 mAh g{sup −1}. ► The use of prepared electrolyte significantly improved the cell performance. -- Abstract: A new approach for fabricating polymer gel electrolytes (PGEs) based on electrospun poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) incorporated with layered nanoclay has been employed to enhance the ionic conductivity and electrochemical properties of P(VdF-co-HFP) without compromising its mechanical strength. The effect of layered nanoclay on properties of membranes has been evaluated by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Surface morphology of the membranes has been studied using field-emission scanning electron microscopy (FE-SEM). Polymer gel electrolytes are prepared by soaking the fibrous membrane into 1 M LiPF{sub 6} in EC/DEC. The electrochemical studies show that incorporation of layered nanoclay into the polymer matrix greatly enhanced the ionic conductivity and compatibility with lithium electrodes. The charge–discharge properties and cycling performance of Li/LiFePO{sub 4} cells comprising nanocomposite polymer gel electrolytes have been evaluated at room temperature.

  16. Improvement of N-phthaloylchitosan based gel polymer electrolyte in dye-sensitized solar cells using a binary salt system.

    Science.gov (United States)

    Yusuf, S N F; Azzahari, A D; Selvanathan, V; Yahya, R; Careem, M A; Arof, A K

    2017-02-10

    A binary salt system utilizing lithium iodide (LiI) as the auxiliary component has been introduced to the N-phthaloylchitosan (PhCh) based gel polymer electrolyte consisting of ethylene carbonate (EC), dimethylformamide (DMF), tetrapropylammonium iodide (TPAI), and iodine (I2) in order to improve the performance of dye-sensitized solar cell (DSSC) with efficiency of 6.36%, photocurrent density, JSC of 17.29mAcm(-2), open circuit voltage, VOC of 0.59V and fill factor, FF of 0.62. This efficiency value is an improvement from the 5.00% performance obtained by the DSSC consisting of only TPAI single salt system. The presence of the LiI in addition to the TPAI improves the charge injection rates and increases the iodide contribution to the total conductivity and both factors contribute to the increase in efficiency of the DSSC. The interaction behavior between polymer-plasticizer-salt was thoroughly investigated using EIS, FTIR spectroscopy and XRD.

  17. Li/LiFePO4 batteries with gel polymer electrolytes incorporating a guanidinium-based ionic liquid cycled at room temperature and 50 °C

    Science.gov (United States)

    Li, Mingtao; Yang, Li; Fang, Shaohua; Dong, Siming; Jin, Yide; Hirano, Shin-ichi; Tachibana, Kazuhiro

    2011-08-01

    Gel polymer electrolytes composed of PVdF-HFP microporous membrane incorporating a guanidinium-based ionic liquid with 0.8 mol kg-1 lithium bis(trifluoromethanesulfonylimide) are characterized as the electrolytes in Li/LiFePO4 batteries. The ionic conductivity of these gel polymer electrolytes is 3.16 × 10-4 and 8.32 × 10-4 S cm-1 at 25 and 50 °C, respectively. The electrolytes show good interfacial stability towards lithium metal and high oxidation stability, and the decomposition potential reaches 5.3 and 4.6 V (vs. Li/Li+) at 25 and 50 °C, respectively. Li/LiFePO4 cells using the PVdF-HFP/1g13TFSI-LiTFSI electrolytes show good discharge capacity and cycle stability, and no significant loss in discharge capacity of the battery is observed over 100 cycles. The cells deliver the capacity of 142 and 150 mAh g-1 at the 100th cycling at 25 and 50 °C, respectively.

  18. A microporous gel electrolyte based on poly(vinylidene fluoride-co-hexafluoropropylene)/fully cyanoethylated cellulose derivative blend for lithium-ion battery

    Energy Technology Data Exchange (ETDEWEB)

    Ren Zhong [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China); Liu Yuyan [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China)], E-mail: liuyy@hit.edu.cn; Sun Kening; Zhou Xiaoliang; Zhang Naiqing [Science Reseach Center, Harbin Institute of Technology, Harbin 150001 (China)

    2009-02-15

    A gel polymer electrolyte based on the blend of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and fully cyanoethylated cellulose derivative (DH-4-CN) was prepared and characterized. Thermal, mechanical, swelling, liquid electrolyte retention and electrochemical properties, as well as microstructures of the prepared polymer electrolytes, were investigated using thermogravimetric analysis, electrochemical impedance spectroscopy, linear sweep voltammetry, and scanning electron microscopy. The results showed that the addition of DH-4-CN could obviously improve the conductivity of PVDF-HFP based electrolyte. The maximum ionic conductivity of 4.36 mS cm{sup -1} at 20 deg. C can be obtained for PVDF-HFP/DH-4-CN 14:1 in the presence of 1 M LiPF{sub 6} in EC and DMC (1:1, w/w). The dry blend membranes exhibit excellent thermal behavior. All the blend electrolytes are electrochemically stable up to about 4.8 V vs. Li/Li{sup +} for all compositions. The results reveal that the composite polymer electrolyte qualifies as a potential application in lithium-ion battery.

  19. Efficiency enhancement in dye sensitized solar cells using gel polymer electrolytes based on a tetrahexylammonium iodide and MgI2 binary iodide system.

    Science.gov (United States)

    Bandara, T M W J; Dissanayake, M A K L; Jayasundara, W J M J S R; Albinsson, I; Mellander, B-E

    2012-06-28

    Quasi-solid-state dye-sensitized solar cells have drawn the attention of scientists and technologists as a potential candidate to supplement future energy needs. The conduction of iodide ions in quasi-solid-state polymer electrolytes and the performance of dye sensitized solar cells containing such electrolytes can be enhanced by incorporating iodides having appropriate cations. Gel-type electrolytes, based on PAN host polymers and mixture of salts tetrahexylammonium iodide (Hex4N(+)I(-)) and MgI2, were prepared by incorporating ethylene carbonate and propylene carbonate as plasticizers. The salt composition in the binary mixture was varied in order to optimize the performance of solar cells. The electrolyte containing 120% Hex4N(+)I(-) with respect to weight of PAN and without MgI2 showed the highest conductivity out of the compositions studied, 2.5 × 10(-3) S cm(-1) at 25 °C, and a glass transition at -102.4 °C. However, the electrolyte containing 100% Hex4N(+)I(-) and 20% MgI2 showed the best solar cell performance highlighting the influence of the cation on the performance of the cell. The predominantly ionic behaviour of the electrolytes was established from the dc polarization data and all the electrolytes exhibit iodide ion transport. Seven different solar cells were fabricated employing different electrolyte compositions. The best cell using the electrolyte with 100% Hex4N(+)I(-) and 20% MgI2 with respect to PAN weight showed 3.5% energy conversion efficiency and 8.6 mA cm(-2) short circuit current density.

  20. High-Performance and Stable Gel-State Dye-Sensitized Solar Cells Using Anodic TiO2 Nanotube Arrays and Polymer-Based Gel Electrolytes.

    Science.gov (United States)

    Seidalilir, Zahra; Malekfar, Rasoul; Wu, Hui-Ping; Shiu, Jia-Wei; Diau, Eric Wei-Guang

    2015-06-17

    Highly ordered and vertically oriented TiO2 nanotube (NT) arrays were synthesized with potentiostatic anodization of Ti foil and applied to fabricate gel-state dye-sensitized solar cells (DSSCs). The open structure of the TiO2 NT facilitates the infiltration of the gel-state electrolyte; their one-dimensional structural feature provides effective charge transport. TiO2 NTs of length L=15-35 μm were produced on anodization for periods of t=5-15 h at a constant voltage of 60 V, and sensitized with N719 for photovoltaic characterization. A commercially available copolymer, poly(methyl methacrylate-co-ethyl acrylate) (PMMA-EA), served as a gelling agent to prepare a polymer-gel electrolyte (PGE) for DSSC applications. The PGE as prepared exhibited a maximum conductivity of 4.58 mS cm(-1) with PMMA-EA (7 wt %). The phase transition temperature (Tp) of the PGE containing PMMA-EA at varied concentrations was determined on the basis of the viscosities measured at varied temperatures. Tp increased with increasing concentration of PMMA-EA. An NT-DSSC with L=30 μm assembled using a PGE containing PMMA-EA (7 wt %) exhibited an overall power conversion efficiency (PCE) of 6.9%, which is comparable with that of a corresponding liquid-type device, PCE=7.1%. Moreover, the gel-state NT-DSSC exhibited excellent thermal and light-soaking enduring stability: the best device retained ∼90% of its initial efficiency after 1000 h under 1 sun of illumination at 50 °C, whereas its liquid-state counterpart decayed appreciably after light soaking for 500 h.

  1. Flexible polyester cellulose paper supercapacitor with a gel electrolyte.

    Science.gov (United States)

    Karthika, Prasannan; Rajalakshmi, Natarajan; Dhathathreyan, Kaveripatnam S

    2013-11-11

    A low-cost polyester cellulose paper has been used as a substrate for a flexible supercapacitor device that contains aqueous carbon nanotube ink as the electrodes and a polyvinyl alcohol (PVA)-based gel as the electrolyte. Gel electrolytes have attracted much interest due to their solvent-holding capacity and good film-forming capability. The electrodes are characterized for their conductivity and morphology. Because of its high conductivity, the conductive paper is studied in supercapacitor applications as active electrodes and as separators after coating with polyvinylidene fluoride. Carbon nanotubes deposited on porous paper are more accessible to ions in the electrolyte than those on flat substrates, which results in higher power density. A simple fabrication process is achieved and paper supercapacitors are tested for their performance in both aqueous and PVA gel electrolytes by using galvanostatic and cyclic voltammetry methods. A high specific capacitance of 270 F g(-1) and an energy density value of 37 W h kg(-1) are achieved for devices with PVA gel electrolytes. Furthermore, this device can maintain excellent specific capacitance even under high currents. This is also confirmed by another counter experiment with aqueous sulfuric acid as the electrolyte. The cycle life, one of the most critical parameters in supercapacitor operations, is found to be excellent (6000 cycles) and less than 0.5 % capacitance loss is observed. Moreover, the supercapacitor device is flexible and even after twisting does not show any cracks or evidence of breakage, and shows almost the same specific capacitance of 267 F g(-1) and energy density of 37 W h kg(-1) . This work suggests that a paper substrate can be a highly scalable and low-cost solution for high-performance supercapacitors.

  2. A zwitterionic gel electrolyte for efficient solid-state supercapacitors

    OpenAIRE

    Peng, Xu; Liu, Huili; Yin, Qin; Wu, Junchi; Chen, Pengzuo; Zhang, Guangzhao; Liu, Guangming; Wu, Changzheng; Xie, Yi

    2016-01-01

    Gel electrolytes have attracted increasing attention for solid-state supercapacitors. An ideal gel electrolyte usually requires a combination of advantages of high ion migration rate, reasonable mechanical strength and robust water retention ability at the solid state for ensuring excellent work durability. Here we report a zwitterionic gel electrolyte that successfully brings the synergic advantages of robust water retention ability and ion migration channels, manifesting in superior electro...

  3. Lithium ion conducting PVdF-HFP composite gel electrolytes based on N-methoxyethyl- N-methylpyrrolidinium bis(trifluoromethanesulfonyl)-imide ionic liquid

    Science.gov (United States)

    Ferrari, S.; Quartarone, E.; Mustarelli, P.; Magistris, A.; Fagnoni, M.; Protti, S.; Gerbaldi, C.; Spinella, A.

    Blends of PVdF-HFP and ionic liquids (ILs) are interesting for application as electrolytes in plastic Li batteries. They combine the advantages of the gel polymer electrolytes (GPEs) swollen by conventional organic liquid electrolytes with the nonflammability, and high thermal and electrochemical stability of ILs. In this work we prepared and characterized PVdF-HFP composite membranes swollen with a solution of LiTFSI in ether-functionalized pyrrolidinium-imide ionic liquid (PYRA 12O1TFSI). The membranes were filled in with two different types of silica: (i) mesoporous SiO 2 (SBA-15) and (ii) a commercial nano-size one (HiSil™ T700). The ionic conductivity and the electrochemical properties of the gel electrolytes were studied in terms of the nature of the filler. The thermal and the transport properties of the composite membranes are similar. In particular, room temperature ionic conductivities higher than 0.25 mS cm -1 are easily obtained at defined filler contents. However, the mesoporous filler guarantees higher lithium transference numbers, a more stable electrochemical interface and better cycling performances. Contrary to the HiSil™-based membrane, the Li/LiFePO 4 cells with PVdF-HFP/PYRA 12O1TFSI-LiTFSI films containing 10 wt% of SBA-15 show good charge/discharge capacity, columbic efficiency close to unity, and low capacity losses at medium C-rates during 180 cycles.

  4. Nonflammable gel electrolyte containing alkyl phosphate for rechargeable lithium batteries

    Science.gov (United States)

    Yoshimoto, Nobuko; Niida, Yoshihiro; Egashira, Minato; Morita, Masayuki

    A nonflammable polymeric gel electrolyte has been developed for rechargeable lithium battery systems. The gel film consists of poly(vinylidenefluoride- co-hexafluoropropylene) (PVdF-HFP) swollen with lithium hexafluorophosphate (LiPF 6) solution in ternary solvent containing trimethyl phosphate (TMP). High ionic conductivity of 6.2 mS cm -1 at 20 °C was obtained for the gel electrolyte consisting of 0.8 M LiPF 6/EC + DEC + TMP (55:25:20) with PVdF-HFP, which is comparable to that of the liquid electrolyte containing the same electrolytic salt. Addition of a small amount of vinylene carbonate (VC) in the gel electrolyte improved the rechargeability of a graphite electrode. The rechargeable capacity of the graphite in the gel containing VC was ca. 300 mAh g -1, which is almost the same as that in a conventional liquid electrolyte system.

  5. Conductivity behaviour of polymer gel electrolytes: Role of polymer

    Indian Academy of Sciences (India)

    S S Sekhon

    2003-04-01

    Polymer is an important constituent of polymer gel electrolytes along with salt and solvent. The salt provides ions for conduction and the solvent helps in the dissolution of the salt and also provides the medium for ion conduction. Although the polymer added provides mechanical stability to the electrolytes yet its effect on the conductivity behaviour of gel electrolytes as well as the interaction of polymer with salt and solvent has not been conclusively established. The conductivity of lithium ion conducting polymer gel electrolytes decreases with the addition of polymer whereas in the case of proton conducting polymer gel electrolytes an increase in conductivity has been observed with polymer addition. This has been explained to be due to the role of polymer in increasing viscosity and carrier concentration in these gel electrolytes.

  6. In situ gelation of Al(III)-4-tert-butylpyridine based metal-organic gel electrolyte for efficient quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Dong, Yu-Jie; Rao, Hua-Shang; Cao, Yang; Chen, Hong-Yan; Kuang, Dai-Bin; Su, Cheng-Yong

    2017-03-01

    A novel Al(III)-4-tert-butylpyridine (TBP) gel electrolyte is successfully achieved by a simple and facile in situ gelation method and applied as quasi-solid-state electrolyte for dye-sensitized solar cells (DSSCs). Through directly adding Al3+ into the TBP solution, the induced hydrolysis of Al3+ and the coordination interaction between Al3+ and TBP facilitates the formation of metal-organic gels(MOGs), in which such bi-functional TBP molecules will act as both gelators and active additives to tailor the performance of electrolytes. In addition, the gel electrolytes can largely preserve the properties of liquid electrolyte and penetrate well into the TiO2 photoanode film. Both Al3+ and TBP in the gel electrolytes affect the performance of cells. The Jsc of gel electrolytes decrease with the increasing concentration of gelators due to the enhanced strength and viscosity of the gel electrolytes, while the competition between Al3+ and TBP causes conduction band edge shift and electron recombination, leading to a variation of Voc. Herein, by tuning the molar ratio of Al3+/TBP, an impressive conversion efficiency of 8.25% is obtained, indicating a promising protocol of preparing MOGs not only to achieve high performance in solar cells, but also opens up extended scopes in other energy-related fields such as catalysis.

  7. Electrochemistry of polyamidoamine dendrimers ester gel electrolytes

    Institute of Scientific and Technical Information of China (English)

    CHEN Hong; MO Zunli

    2004-01-01

    This paper described the first example of polyamidoamine dendrimers ester (PAMAM) used as a gel electrolyte with a short-chain polyethylene glycol (MPEG-400) as a plasticizer. The polymer films are solid and sticky. Background cyclic voltammetry (CV) shows a potential window between +0.7 and -0.7 V vs. Ag/AgCl. The voltammetry of ferrocene and 7,7,8,8-tetracyanoquinodimethane (TCNQ) indicates that diffusion coefficients are in the range of 10-a-10-9 cm2/s.Ionic conductivities are approximately 10-6 S/cm. Similar films using dimethyl sulfoxide (DMSO) as a plasticizer instead of MPEG-400 have demonstrated ionic conductivities of 10-4 S/cra and reversible voltammetry. However, UV spectrophotometry shows that 70% of the DMSO is lost under vacuum, indicating the difficulty in quantifying the DMSO content when exposed to vacuum.

  8. High-performance gel electrolytes with tetra-armed polymer network for Li ion batteries

    Science.gov (United States)

    Hazama, Taisuke; Fujii, Kenta; Sakai, Takamasa; Aoki, Masahiro; Mimura, Hideyuki; Eguchi, Hisao; Todorov, Yanko; Yoshimoto, Nobuko; Morita, Masayuki

    2015-07-01

    An organo gel with only 6 wt % tetra-armed poly(ethylene glycol), TetraPEG, was prepared and applied as a novel gel electrolyte for Li ion batteries (LIBs). The TetraPEG gel electrolyte containing 1.0 M LiPF6 in binary or ternary mixtures, i.e., EC + DEC and EC + DEC + TFEP (EC: ethylene carbonate, DEC: diethyl carbonate and TFEP: tris(2,2,2-trifluoroethyl)phosphate showed high ionic conductivity required for the use in LIB systems. The TetraPEG gel based on ternary EC + DEC + TFEP system acts as a nonflammable gel electrolyte at the TFEP content higher than 20 vol%. In cyclic voltammetry and charge/discharge cycling tests, the TetraPEG gel electrolytes showed good reversibility for a graphite negative electrode.

  9. High optical and switching performance electrochromic devices based on a zinc oxide nanowire with poly(methyl methacrylate) gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Chun, Young Tea; Chu, Daping, E-mail: dpc31@cam.ac.uk [Electrical Engineering Division, Department of Engineering, University of Cambridge, 9 JJ Thomson Avenue, Cambridge CB3 0FA (United Kingdom); Neeves, Matthew; Placido, Frank [Thin Film Centre, University of the West of Scotland, Paisley PA1 2BE (United Kingdom); Smithwick, Quinn [Disney Research, 521 Circle Seven Drive, Glendale, Los Angeles, California 91201 (United States)

    2014-11-10

    High performance electrochromic devices have been fabricated and demonstrated utilizing a solid polymer electrolyte and zinc oxide (ZnO) nanowire (NW) array counter electrode. The poly(methyl methacrylate) based polymer electrolyte was spin coated upon hydrothermally grown ZnO NW array counter electrodes, while electron beam evaporated NiO{sub x} thin films formed the working electrodes. Excellent optical contrast and switching speeds were observed in the fabricated devices with active areas of 2 cm{sup 2}, exhibiting an optical contrast of 73.11% at the wavelength of 470 nm, combined with a fast switching time of 0.2 s and 0.4 s for bleaching and coloration, respectively.

  10. Lithium ion conducting PVdF-HFP composite gel electrolytes based on N-methoxyethyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)-imide ionic liquid

    Energy Technology Data Exchange (ETDEWEB)

    Ferrari, S.; Quartarone, E.; Mustarelli, P.; Magistris, A. [Dept. of Physical Chemistry, University of Pavia, Via Taramelli 16, 27100 Pavia (Italy); Fagnoni, M.; Protti, S. [Dept. of Organic Chemistry, University of Pavia, Via Taramelli 12, 27100 Pavia (Italy); Gerbaldi, C. [Dept. of Material Science and Chemical Engineering, Politecnico di Torino, C.so Duca degli Abruzzi, 24, 10129 Torino (Italy); Spinella, A. [Centro Grandi Apparecchiature - UniNetLab, University of Palermo, Via F. Marini 14, 90128 Palermo (Italy)

    2010-01-15

    Blends of PVdF-HFP and ionic liquids (ILs) are interesting for application as electrolytes in plastic Li batteries. They combine the advantages of the gel polymer electrolytes (GPEs) swollen by conventional organic liquid electrolytes with the nonflammability, and high thermal and electrochemical stability of ILs. In this work we prepared and characterized PVdF-HFP composite membranes swollen with a solution of LiTFSI in ether-functionalized pyrrolidinium-imide ionic liquid (PYRA{sub 12O1}TFSI). The membranes were filled in with two different types of silica: (i) mesoporous SiO{sub 2} (SBA-15) and (ii) a commercial nano-size one (HiSil trademark T700). The ionic conductivity and the electrochemical properties of the gel electrolytes were studied in terms of the nature of the filler. The thermal and the transport properties of the composite membranes are similar. In particular, room temperature ionic conductivities higher than 0.25 mS cm{sup -1} are easily obtained at defined filler contents. However, the mesoporous filler guarantees higher lithium transference numbers, a more stable electrochemical interface and better cycling performances. Contrary to the HiSil trademark -based membrane, the Li/LiFePO{sub 4} cells with PVdF-HFP/PYRA{sub 12O1}TFSI-LiTFSI films containing 10 wt% of SBA-15 show good charge/discharge capacity, columbic efficiency close to unity, and low capacity losses at medium C-rates during 180 cycles. (author)

  11. A novel lithium/sulfur battery based on sulfur/graphene nanosheet composite cathode and gel polymer electrolyte.

    Science.gov (United States)

    Zhang, Yongguang; Zhao, Yan; Bakenov, Zhumabay

    2014-03-21

    A novel sulfur/graphene nanosheet (S/GNS) composite was prepared via a simple ball milling of sulfur with commercial multi-layer graphene nanosheet, followed by a heat treatment. High-resolution transmission and scanning electronic microscopy observations showed the formation of irregularly interlaced nanosheet-like structure consisting of graphene with uniform sulfur coating on its surface. The electrochemical properties of the resulting composite cathode were investigated in a lithium cell with a gel polymer electrolyte (GPE) prepared by trapping 1 mol dm-3 solution of lithium bistrifluoromethanesulfonamide in tetraethylene glycol dimethyl ether in a polymer matrix composed of poly(vinylidene fluoride-co-hexafluoropropylene)/poly(methylmethacrylate)/silicon dioxide (PVDF-HFP/PMMA/SiO2). The GPE battery delivered reversible discharge capacities of 809 and 413 mAh g-1 at the 1st and 50th cycles at 0.2C, respectively, along with a high coulombic efficiency over 50 cycles. This performance enhancement of the cell was attributed to the suppression of the polysulfide shuttle effect by a collective effect of S/GNS composite cathode and GPE, providing a higher sulfur utilization.

  12. A novel lithium/sulfur battery based on sulfur/graphene nanosheet composite cathode and gel polymer electrolyte

    Science.gov (United States)

    Zhang, Yongguang; Zhao, Yan; Bakenov, Zhumabay

    2014-03-01

    A novel sulfur/graphene nanosheet (S/GNS) composite was prepared via a simple ball milling of sulfur with commercial multi-layer graphene nanosheet, followed by a heat treatment. High-resolution transmission and scanning electronic microscopy observations showed the formation of irregularly interlaced nanosheet-like structure consisting of graphene with uniform sulfur coating on its surface. The electrochemical properties of the resulting composite cathode were investigated in a lithium cell with a gel polymer electrolyte (GPE) prepared by trapping 1 mol dm-3 solution of lithium bistrifluoromethanesulfonamide in tetraethylene glycol dimethyl ether in a polymer matrix composed of poly(vinylidene fluoride-co-hexafluoropropylene)/poly(methylmethacrylate)/silicon dioxide (PVDF-HFP/PMMA/SiO2). The GPE battery delivered reversible discharge capacities of 809 and 413 mAh g-1 at the 1st and 50th cycles at 0.2C, respectively, along with a high coulombic efficiency over 50 cycles. This performance enhancement of the cell was attributed to the suppression of the polysulfide shuttle effect by a collective effect of S/GNS composite cathode and GPE, providing a higher sulfur utilization. PACS: 82.47.Aa; 82.45.Gj; 62.23.Kn

  13. Electrochemistry of poly(3,4-ethylenedioxythiophene)-polyaniline/ Prussian blue electrochromic devices containing an ionic liquid based gel electrolyte film.

    Science.gov (United States)

    Deepa, Melepurath; Awadhia, Arvind; Bhandari, Shweta

    2009-07-21

    Electrochromic devices based on poly(3,4-ethylenedioxythiophene) (PEDOT) as the cathodic coloring electrode and polyaniline (PANI) or Prussian blue (PB) as the counter electrode containing a highly conductive, self-supporting, distensible and transparent polymer-gel electrolyte film encapsulating an ionic liquid, 1-butyl-1-methylpyrrolidiniumbis-(trifluoromethylsulfonyl)imide, have been fabricated. Polarization, charge transfer and diffusion processes control the electrochemistry of the functional electrodes during coloration and bleaching and these phenomena differ when PEDOT and PANI/PB were employed alternately as working electrodes. While the electrochemical impedance response shows good similitude for PEDOT and PANI electrodes, the responses of PEDOT and PB were significantly different in the PEDOT-PB device, especially during reduction of PB, wherein the overall amplitude of the impedance response is enormous. Large values of the coloration efficiency maxima of 281 cm2 C(-1) (lambda = 583 nm) and 274 cm2 C(-1) (lambda = 602 nm), achieved at -1.0 and -1.5 V for the PEDOT PANI and PEDOT-PB devices have been correlated to the particularly low magnitude of charge transfer resistance and high polarization capacitance operative at the PEDOT ionic liquid based electrolyte interface at these dc potentials, thus allowing facile ion-transport and consequently resulting in enhanced absorption modulation. Moderately fast switching kinetics and the ability of these devices to sustain about 2500 cycles of clear-to-dark and dark-to-clear without incurring major losses in the optical contrast, along with the ease of construction of these cells in terms of high scalability and reproducibility of the synthetic procedure for fabrication of the electrochromic films and the ionic liquid based gel electrolyte film, are indicators of the promise these devices hold for practical applications like electrochromic windows and displays.

  14. Enhancing the performance of dye-sensitized solar cells by incorporating nanosilicate platelets in gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Yi-Hsuan; Chen, Jian-Ging; Wang, Chun-Chieh [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Chiu, Chih-Wei [Department of Chemical Engineering, National Chung Hsing University, Taichung 40227 (China); Lin, Jiang-Jen [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China); Lin, King-Fu [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China); Department of Materials Science and Engineering, National Taiwan University, Taipei 10617 (China); Ho, Kuo-Chuan [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China)

    2009-10-15

    Two kinds of gel-type dye-sensitized solar cells (DSSCs), composed of two types of electrolytes, were constructed and the respective cell performance was evaluated in this study. One electrolyte, TEOS-Triton X-100 gel, was based on a hybrid organic/inorganic gel electrolyte made by the sol-gel method and the other was based on poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP) copolymer. TEOS-Triton X-100 gel was based on the reticulate structure of silica, formed by hydrolysis, and condensation of tetraethoxysilane (TEOS), while its organic subphase was a mixture of surfactant (Triton X-100) and ionic liquid electrolytes. Both DSSC gel-type electrolytes were composed of iodine, 1-propy-3-methyl-imidazolium iodide, and 3-methoxypropionitrile to create the redox couple of I{sub 3}{sup -}/I{sup -}. Based on the results obtained from the I-V characteristics, it was found that the optimal iodine concentrations for the TEOS-Triton X-100 gel electrolyte and PVDF-HFP gel electrolyte are 0.05 M and 0.1 M, respectively. Although the increase in the iodine concentration could enhance the short-circuit current density (J{sub SC}), a further increase in the iodine concentration would reduce the J{sub SC} due to increased dark current. Therefore, the concentration of I{sub 2} is a significant factor in determining the performance of DSSCs. In order to enhance cell performance, the addition of nanosilicate platelets (NSPs) in the above-mentioned gel electrolytes was investigated. By incorporating NSP-Triton X-100 into the electrolytes, the J{sub SC} of the cells increased due to the decrease of diffusion resistance, while the open circuit voltage (V{sub OC}) remained almost the same. As the loading of the NSP-Triton X-100 in the TEOS-Triton X-100 gel electrolyte increased to 0.5 wt%, the J{sub SC} and the conversion efficiency increased from 8.5 to 12 mA/cm{sup 2} and from 3.6% to 4.7%, respectively. However, the J{sub SC} decreased as the loading of NSP-Triton X-100

  15. Enhancing the performance of dye-sensitized solar cells by incorporating nanosilicate platelets in gel electrolyte

    KAUST Repository

    Lai, Yi-Hsuan

    2009-10-01

    Two kinds of gel-type dye-sensitized solar cells (DSSCs), composed of two types of electrolytes, were constructed and the respective cell performance was evaluated in this study. One electrolyte, TEOS-Triton X-100 gel, was based on a hybrid organic/inorganic gel electrolyte made by the sol-gel method and the other was based on poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP) copolymer. TEOS-Triton X-100 gel was based on the reticulate structure of silica, formed by hydrolysis, and condensation of tetraethoxysilane (TEOS), while its organic subphase was a mixture of surfactant (Triton X-100) and ionic liquid electrolytes. Both DSSC gel-type electrolytes were composed of iodine, 1-propy-3-methyl-imidazolium iodide, and 3-methoxypropionitrile to create the redox couple of I3 -/I-. Based on the results obtained from the I-V characteristics, it was found that the optimal iodine concentrations for the TEOS-Triton X-100 gel electrolyte and PVDF-HFP gel electrolyte are 0.05 M and 0.1 M, respectively. Although the increase in the iodine concentration could enhance the short-circuit current density (JSC), a further increase in the iodine concentration would reduce the JSC due to increased dark current. Therefore, the concentration of I2 is a significant factor in determining the performance of DSSCs. In order to enhance cell performance, the addition of nanosilicate platelets (NSPs) in the above-mentioned gel electrolytes was investigated. By incorporating NSP-Triton X-100 into the electrolytes, the JSC of the cells increased due to the decrease of diffusion resistance, while the open circuit voltage (VOC) remained almost the same. As the loading of the NSP-Triton X-100 in the TEOS-Triton X-100 gel electrolyte increased to 0.5 wt%, the JSC and the conversion efficiency increased from 8.5 to 12 mA/cm2 and from 3.6% to 4.7%, respectively. However, the JSC decreased as the loading of NSP-Triton X-100 exceeded 0.5 wt%. At higher NSP-Triton X-100 loading, NSPs acted as

  16. Research progress of modifying P(VDF-HFP)based gel polymer electrolyte%改性P(VDF-HFP)基凝胶聚合物电解质研究进展

    Institute of Scientific and Technical Information of China (English)

    梁子雷; 李琪; 孙悦; 乔庆东

    2009-01-01

    Gel polymer electrolyte is one of the priority materials for advanced lithium ion battery research. It plays an important role in lithium ion battery's development. The research progress in recent years in modifying P(VDF-HFP) based gel polymer electrolytes for polymer Li-ion battery was reviewed. The preparation and ionic conductivity of hybrid gel polymer electrolyte (HGPE) and nanocomposites gel polymer electrolyte (NGPE) was comprehensively introduced. The application prospect of P (VDF-HFP) based gel polymer electrolyte for Li-ion battery was put forward.%凝胶聚合物电解质是先进锂离子电池材料研究的重点之一,对其未来的发展起到至关重要的作用.总结了国内外近年来聚合物锂离子电池改性P(VDF-HFP);凝胶聚合物电解质的研究成果;重点介绍了共混凝胶聚合物电解质和纳米复合凝胶聚合物电解质的制备方法及其离子导电性;并对P(VDF-HFP)基凝胶聚合物电解质在锂离子电池中的应用做出了展望.

  17. Development of Radiation Curable polymeric Gel Electrolyte Formulation

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Jin Hoo; Kim, Hyun Kyung; Shin, Choon Hee; Han, Chang Ho; Kim, Ki Ho [Chosun University, Gwangju (Korea, Republic of)

    2010-06-15

    The result of this study, the free lithium ions of polymer gel electrolyte containing hydroxyproply Cellulose 1% is the most excellent due to irradiate of strong energy over quick time, although curing reaction of EB system is a very fast, polymer gel electrolyte containing hydroxypropyl Cellulose Fabricated by UV system is excellent curing reaction and ionic conductivity and mechanical properties and thermal stability than EB system

  18. In situ ceramic fillers of electrospun thermoplastic polyurethane/poly(vinylidene fluoride) based gel polymer electrolytes for Li-ion batteries

    Science.gov (United States)

    Wu, Na; Cao, Qi; Wang, Xianyou; Li, Sheng; Li, Xiaoyun; Deng, Huayang

    Gel polymer electrolyte films based on thermoplastic polyurethane (TPU)/poly(vinylidene fluoride) (PVdF) with and without in situ ceramic fillers (SiO 2 and TiO 2) are prepared by electrospinning 9 wt% polymer solution at room temperature. The electrospun TPU-PVdF blending membrane with 3% in situ TiO 2 shows a highest ionic conductivity of 4.8 × 10 -3 S cm -1 with electrochemical stability up to 5.4 V versus Li +/Li at room temperature and has a high tensile strength (8.7 ± 0.3 MPa) and % elongation at break (110.3 ± 0.2). With the superior electrochemical and mechanical performance, it is very suitable for application in polymer lithium ion batteries.

  19. Alkylphosphate-based nonflammable gel electrolyte for LiMn{sub 2}O{sub 4} positive electrode in lithium-ion battery

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimoto, Nobuko; Gotoh, Daisuke; Egashira, Minato; Morita, Masayuki [Graduate School of Science and Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube 755-8611 (Japan)

    2008-12-01

    Polymeric gel containing alkylphosphate has been examined as nonflammable gel electrolyte for LiMn{sub 2}O{sub 4} positive electrode of lithium-ion battery (LIB). The gel was composed of a polymer matrix of poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP) and a liquid component consisting of ternary solvent of trimethyl phosphate (TMP) mixed with ethylene carbonate (EC) and diethyl carbonate (DEC) that dissolves lithium salt (LiPF{sub 6} or LiBF{sub 4}). The gel composition of 0.8 M (mol dm{sup -3}) LiX (X = PF{sub 6} and BF{sub 4}) dissolved in EC + DEC + TMP (55:25:20) with PVdF-HFP showed excellent nonflammable characteristics and high ionic conductivity of ca. 3.1 mS cm{sup -1} at room temperature (20 C). The charge-discharge cycling test of LiMn{sub 2}O{sub 4} positive electrode gave good reversibility with high capacitance in the gel electrolyte. With respect to the electrolyte salt, LiBF{sub 4} was better than LiPF{sub 6} due to its thermal stability during the gel preparation. (author)

  20. Electrochemical performances of electric double layer capacitor with UV-cured gel polymer electrolyte based on poly[(ethylene glycol)diacrylate]-poly(vinylidene fluoride) blend

    Energy Technology Data Exchange (ETDEWEB)

    Chunmo Yang; Joongkee Lee; Wonil Cho; Byungwon Cho [Korea Inst. of Science and Technology, Eco-Nano Research Center, Seoul (Korea); Jehbeck Ju [Hongik Univ., Dept. of Chemical Engineering, Seoul (Korea)

    2005-03-01

    Poly[(ethylene glycol)diacrylate]-poly(vinylidene fluoride), a gel polymer blend with ethylene carbonate:dimethyl carbonate:ethylmethyl carbonate (EC:DMC:EMC, 1:1:1 volume ratio) and containing 1.0 M of lithium hexafluoro phosphate (LiPF{sub 6}) as liquid components, is employed as a gel polymer electrolyte for an electric double layer capacitor (EDLC). Its electrochemical characteristics is compared with that of liquid organic electrolyte mixture of ethylene carbonate, dimethyl carbonate and ethylmethyl carbonate in a 1:1:1 volume ratio containing 1.0 M LiPF{sub 6} salt. The specific surface area of the activated carbon powder as an active material is 1908 m{sup 2}/g. Liquid poly[(ethylene glycol)diacrylate] (PEGDA) oligomer with a high retention capability of liquid electrolytes is cured by UV irradiation and poly(vinylidene fluoride)-hexafluoropropylene (PVdF-HFP) copolymer with a porous structure endows polymer matrix with high mechanical strength. The specific capacitance of EDLC using the gel polymer electrolyte (GPE-EDLC) shows 120 F/g, which is better than the liquid organic electrolyte. Good cycling efficiency is observed for a GPE-EDLC with high retention capability of liquid components. The high specific capacitance and good cycling efficiency are most likely due to the polarization resistance of EDLC with the gel polymer electrolyte, which is lower than the liquid organic electrolyte. This may result from the distinguished adhesion between the activated carbon electrode and the gel polymer electrolyte, as well as high retention capability of liquid components. Power densities of GPE-EDLC and LOE-EDLC shows 1.88 kW/kg and 1.21 kW/kg, respectively. However, the energy densities are low in both electrolytes. The GPE-EDLC exhibits rectangular cyclic voltammogram similar to an ideal EDLC within operating voltage range of 0 V-2.5 V. It should be noted that a region of electric double layer means a wide voltage and a rapid formation. Redox currents of both

  1. Electrochemical performances of electric double layer capacitor with UV-cured gel polymer electrolyte based on poly[(ethylene glycol)diacrylate]-poly(vinylidene fluoride) blend

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Chun-Mo [Eco-Nano Research Center, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of)]. E-mail: ycm@kist.re.kr; Ju, Jeh Beck [Department of Chemical Engineering, Hongik University, Seoul 121-791 (Korea, Republic of); Lee, Joong Kee [Eco-Nano Research Center, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of); Cho, Won Il [Eco-Nano Research Center, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of); Cho, Byung Won [Eco-Nano Research Center, Korea Institute of Science and Technology, Seoul 130-650 (Korea, Republic of)

    2005-03-01

    Poly[(ethylene glycol)diacrylate]-poly(vinylidene fluoride), a gel polymer blend with ethylene carbonate:dimethyl carbonate:ethylmethyl carbonate (EC:DMC:EMC, 1:1:1 volume ratio) and containing 1.0 M of lithium hexafluoro phosphate (LiPF{sub 6}) as liquid components, is employed as a gel polymer electrolyte for an electric double layer capacitor (EDLC). Its electrochemical characteristics is compared with that of liquid organic electrolyte mixture of ethylene carbonate, dimethyl carbonate and ethylmethyl carbonate in a 1:1:1 volume ratio containing 1.0 M LiPF{sub 6} salt. The specific surface area of the activated carbon powder as an active material is 1908 m{sup 2}/g. Liquid poly[(ethylene glycol)diacrylate] (PEGDA) oligomer with a high retention capability of liquid electrolytes is cured by UV irradiation and poly(vinylidene fluoride)-hexafluoropropylene (PVdF-HFP) copolymer with a porous structure endows polymer matrix with high mechanical strength. The specific capacitance of EDLC using the gel polymer electrolyte (GPE-EDLC) shows 120 F/g, which is better than the liquid organic electrolyte. Good cycling efficiency is observed for a GPE-EDLC with high retention capability of liquid components. The high specific capacitance and good cycling efficiency are most likely due to the polarization resistance of EDLC with the gel polymer electrolyte, which is lower than the liquid organic electrolyte. This may result from the distinguished adhesion between the activated carbon electrode and the gel polymer electrolyte, as well as high retention capability of liquid components. Power densities of GPE-EDLC and LOE-EDLC shows 1.88 kW/kg and 1.21 kW/kg, respectively. However, the energy densities are low in both electrolytes. The GPE-EDLC exhibits rectangular cyclic voltammogram similar to an ideal EDLC within operating voltage range of 0 V-2.5 V. It should be noted that a region of electric double layer means a wide voltage and a rapid formation. Redox currents of both

  2. Structure and properties of Li-ion conducting polymer gel electrolytes based on ionic liquids of the pyrrolidinium cation and the bis(trifluoromethanesulfonyl)imide anion

    Science.gov (United States)

    Pitawala, Jagath; Navarra, Maria Assunta; Scrosati, Bruno; Jacobsson, Per; Matic, Aleksandar

    2014-01-01

    We have investigated the structure and physical properties of Li-ion conducting polymer gel electrolytes functionalized with ionic liquid/lithium salt mixtures. The membranes are based on poly(vinylidene fluoride-co-hexafluoropropylene) copolymer, PVdF-HFP, and two ionic liquids: pyrrolidinium cations, N-butyl-N-methylpyrrolidinium (PyR14+), N-butyl-N-ethylpyrrolidinium (PyR24+), and bis(trifluoromethanesulfonyl)imide anion (TFSI). The ionic liquids where doped with 0.2 mol kg--1 LiTFSI. The resulting membranes are freestanding, flexible, and nonvolatile. The structure of the polymer and the interactions between the polymer and the ionic liquid electrolyte have been studied using Raman spectroscopy. The ionic conductivity of the membranes has been studied using dielectric spectroscopy whereas the thermal properties were investigated using differential scanning caloriometry (DSC). These results show that there is a weak, but noticeable, influence on the physical properties of the ionic liquid by the confinement in the membrane. We observe a change in the Li-ion coordination, conformation of the anion, the fragility and a slight increase of the glass transition temperatures for IL/LiTFSI mixtures in the membranes compared to the neat mixtures. The effect can be related to the confinement of the liquid in the membrane and/or to interactions with the PVdF-HFP polymer matrix where the crystallinity is decreased compared to the starting polymer powder.

  3. Foil-based TiO2/gel electrolyte/Ni1-xO electrochromic device made of electrochromic pigment coatings.

    Science.gov (United States)

    Mihelčič, Mohor; Šurca-Vuk, Angela; Vrhovšk, Dejan; Švegl, Franc; Hajzeri, Metka; Orel, Boris

    2014-01-01

    Thin electrochromic coatings were obtained by co-grinding the mTiA particle aggregates (300 nm in size) with open-corner heptaisobutyl trisilanol POSS (T(8) IB(7)(OH)(3) POSS) acting as dispersant. After the addition of titanium tetraisopropoxide (3-5%) the mTiA pigment dispersion was deposited on FTO glass and plastic ITO PET foils and coatings were obtained by thermal treatment at 150 °C. Optical transmittance and luminous haze from 2 to 6% of the coatings were determined from the corresponding UV-Vis spectra. The achieved electrochromic effect was evaluated by electrochemical charging/discharging in 1 M LiClO(4)/PC electrolyte. Results revealed that the colouring/bleaching changes depended on the extent of grinding and the size of the milling zirconia beads, enabling to distinguish between the surface charging of the mTiA grains and the filling and emptying of the anatase density of states. mTiA pigment coatings deposited on plastic foil were used in combination with Ni(1-x)O pigment coatings for construction of foil-based electrochromic device employing novel gel electrolyte with ionic liquid co-solvent.

  4. Hydrogen production via urea electrolysis using a gel electrolyte

    Science.gov (United States)

    King, Rebecca L.; Botte, Gerardine G.

    2011-03-01

    A technology was demonstrated for the production of hydrogen and other valuable products (nitrogen and clean water) through the electrochemical oxidation of urea in alkaline media. In addition, this process remediates toxic nitrates and prevents gaseous ammonia emissions. Improvements to urea electrolysis were made through replacement of aqueous KOH electrolyte with a poly(acrylic acid) gel electrolyte. A small volume of poly(acrylic acid) gel electrolyte was used to accomplish the electrochemical oxidation of urea improving on the previous requirement for large amounts of aqueous potassium hydroxide. The effect of gel composition was investigated by varying polymer content and KOH concentrations within the polymer matrix in order to determine which is the most advantageous for the electrochemical oxidation of urea and production of hydrogen.

  5. Novel Stable Gel Polymer Electrolyte: Toward a High Safety and Long Life Li-Air Battery.

    Science.gov (United States)

    Yi, Jin; Liu, Xizheng; Guo, Shaohua; Zhu, Kai; Xue, Hailong; Zhou, Haoshen

    2015-10-28

    Nonaqueous Li-air battery, as a promising electrochemical energy storage device, has attracted substantial interest, while the safety issues derived from the intrinsic instability of organic liquid electrolytes may become a possible bottleneck for the future application of Li-air battery. Herein, through elaborate design, a novel stable composite gel polymer electrolyte is first proposed and explored for Li-air battery. By use of the composite gel polymer electrolyte, the Li-air polymer batteries composed of a lithium foil anode and Super P cathode are assembled and operated in ambient air and their cycling performance is evaluated. The batteries exhibit enhanced cycling stability and safety, where 100 cycles are achieved in ambient air at room temperature. The feasibility study demonstrates that the gel polymer electrolyte-based polymer Li-air battery is highly advantageous and could be used as a useful alternative strategy for the development of Li-air battery upon further application.

  6. All-solid-state proton battery using gel polymer electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Kuldeep, E-mail: mishkuldeep@gmail.com [Department of Applied Science and Humanities, ABES Engineering College, Ghaziabad-201009, India and Department of Physics and Materials Science and Engineering, Jaypee Institute of Information Technology, Noida-201307 (India); Pundir, S. S.; Rai, D. K. [Department of Physics and Materials Science and Engineering, Jaypee Institute of Information Technology, Noida-201307 (India)

    2014-04-24

    A proton conducting gel polymer electrolyte system; PMMA+NH{sub 4}SCN+EC/PC, has been prepared. The highest ionic conductivity obtained from the system is 2.5 × 10−4 S cm{sup −1}. The optimized composition of the gel electrolyte has been used to fabricate a proton battery with Zn/ZnSO{sub 4}⋅7H{sub 2}O anode and MnO{sub 2} cathode. The open circuit voltage of the battery is 1.4 V and the highest energy density is 5.7 W h kg−1 for low current drain.

  7. Low-Cost Fabrication for ZrO2-Based Electrolyte Thin-Substrate by Aqueous Gel-Casting

    Institute of Scientific and Technical Information of China (English)

    刘晓光; 李国军; 仝建峰; 陈大明

    2004-01-01

    The possibility to fabricate yttria-stabilized zirconia (YSZ) thin-substrates by aqueous gel casting of high concentrated aqueous slurries was investigated. The effects of dispersant, pH value, and solid content of slurries for gel process on stability and viscosity of slurries were optimized. YSZ thin-substrates green bodies with 100 μm thickness and 100 mm×100 mm flat plate were fabricated. Microstructure observations, density and bending measurements show that these green bodies are homogeneous and highly densified. After sintering at 1873 K×2 h, the ionic conductivity reaches 0.155 S·cm-1 at 1273 K.

  8. Poly(ethylene oxide)-co-poly(propylene oxide)-based gel electrolyte with high ionic conductivity and mechanical integrity for lithium-ion batteries.

    Science.gov (United States)

    Wang, Shih-Hong; Hou, Sheng-Shu; Kuo, Ping-Lin; Teng, Hsisheng

    2013-09-11

    Using gel polymer electrolytes (GPEs) for lithium-ion batteries usually encounters the drawback of poor mechanical integrity of the GPEs. This study demonstrates the outstanding performance of a GPE consisting of a commercial membrane (Celgard) incorporated with a poly(ethylene oxide)-co-poly(propylene oxide) copolymer (P(EO-co-PO)) swelled by a liquid electrolyte (LE) of 1 M LiPF6 in carbonate solvents. The proposed GPE stably holds LE with an amount that is three times that of the Celgard-P(EO-co-PO) composite. This GPE has a higher ionic conductivity (2.8×10(-3) and 5.1×10(-4) S cm(-1) at 30 and -20 °C, respectively) and a wider electrochemical voltage range (5.1 V) than the LE-swelled Celgard because of the strong ion-solvation power of P(EO-co-PO). The active ion-solvation role of P(EO-co-PO) also suppresses the formation of the solid-electrolyte interphase layer. When assembling the GPE in a Li/LiFePO4 battery, the P(EO-co-PO) network hinders anionic transport, producing a high Li+ transference number of 0.5 and decreased the polarization overpotential. The Li/GPE/LiFePO4 battery delivers a discharge capacity of 156-135 mAh g(-1) between 0.1 and 1 C-rates, which is approximately 5% higher than that of the Li/LE/LiFePO4 battery. The IR drop of the Li/GPE/LiFePO4 battery was 44% smaller than that of the Li/LE/LiFePO4. The Li/GPE/LiFePO4 battery is more stable, with only a 1.2% capacity decay for 150 galvanostatic charge-discharge cycles. The advantages of the proposed GPE are its high stability, conductivity, Li+ transference number, and mechanical integrity, which allow for the assembly of GPE-based batteries readily scalable to industrial levels.

  9. Electrolyte transport in neutral polymer gels embedded with charged inclusions

    Science.gov (United States)

    Hill, Reghan

    2005-11-01

    Ion permeable membranes are the basis of a variety of molecular separation technologies, including ion exchange, gel electrophoresis and dialysis. This work presents a theoretical model of electrolyte transport in membranes comprised of a continuous polymer gel embedded with charged spherical inclusions, e.g., biological cells and synthetic colloids. The microstructure mimics immobilized cell cultures, where electric fields have been used to promote nutrient transport. Because several important characteristics can, in principle, be carefully controlled, the theory provides a quantitative framework to help tailor the bulk properties for enhanced molecular transport, microfluidic pumping, and physicochemical sensing applications. This talk focuses on the electroosmotic flow driven by weak electric fields and electrolyte concentration gradients. Also of importance is the influence of charge on the effective ion diffusion coefficients, bulk electrical conductivity, and membrane diffusion potential.

  10. Solid-state supercapacitors with ionic liquid gel polymer electrolyte based on poly (3, 4-ethylenedioxythiophene), carbon nanotubes, and metal oxides nanocomposites for electrical energy storage

    Science.gov (United States)

    Obeidat, Amr M.

    Clean and renewable energy systems have emerged as an important area of research having diverse and significant new applications. These systems utilize different energy storage methods such as the batteries and supercapacitors. Supercapacitors are electrochemical energy storage devices that are designed to bridge the gap between batteries and conventional capacitors. Supercapacitors which store electrical energy by electrical double layer capacitance are based on large surface area structured carbons. The materials systems in which the Faradaic reversible redox reactions store electrical energy are the transition metal oxides and electronically conducting polymers. Among the different types of conducting polymers, poly (3, 4- ethylenedioxythiophene) (PEDOT) is extensively investigated owing to its chemical and mechanical stability. Due to instability of aqueous electrolytes at high voltages and toxicity of organic electrolytes, potential of supercapacitors has not been fully exploited. A novel aspect of this work is in utilizing the ionic liquid gel polymer electrolyte to design solid-state supercapacitors for energy storage. Various electrochemical systems were investigated including graphene, PEDOT, PEDOT-carbon nanotubes, PEDOT-manganese oxide, and PEDOT-iron oxide nanocomposites. The electrochemical performance of solid-state supercapacitor devices was evaluated based on cyclic voltammetry (CV), charge-discharge (CD), prolonged cyclic tests, and electrochemical impedance spectroscopy (EIS) techniques. Raman spectroscopy technique was also utilized to analyze the bonding structure of the electrode materials. The graphene solid-state supercapacitor system displayed areal capacitance density of 141.83 mF cm-2 based on high potential window up to 4V. The PEDOT solid-state supercapacitor system was synthesized in acetonitrile and aqueous mediums achieving areal capacitance density of 219.17 mF cm-2. The hybrid structure of solid-state supercapacitors was also

  11. A Lithium/Polysulfide Battery with Dual-Working Mode Enabled by Liquid Fuel and Acrylate-Based Gel Polymer Electrolyte.

    Science.gov (United States)

    Liu, Ming; Ren, Yuxun; Zhou, Dong; Jiang, Haoran; Kang, Feiyu; Zhao, Tianshou

    2017-01-25

    The low density associated with low sulfur areal loading in the solid-state sulfur cathode of current Li-S batteries is an issue hindering the development of this type of battery. Polysulfide catholyte as a recyclable liquid fuel was proven to enhance both the energy density and power density of the battery. However, a critical barrier with this lithium (Li)/polysulfide battery is that the shuttle effect, which is the crossover of polysulfides and side deposition on the Li anode, becomes much more severe than that in conventional Li-S batteries with a solid-state sulfur cathode. In this work, we successfully applied an acrylate-based gel polymer electrolyte (GPE) to the Li/polysulfide system. The GPE layer can effectively block the detrimental diffusion of polysulfides and protect the Li metal from the side passivation reaction. Cathode-static batteries utilizing 2 M catholyte (areal sulfur loading of 6.4 mg cm(-2)) present superior cycling stability (727.4 mAh g(-1) after 500 cycles at 0.2 C) and high rate capability (814 mAh g(-1) at 2 C) and power density (∼10 mW cm(-2)), which also possess replaceable and encapsulated merits for mobile devices. In the cathode-flow mode, the Li/polysulfide system with catholyte supplied from an external tank demonstrates further improved power density (∼69 mW cm(-2)) and stable cycling performance. This novel and simple Li/polysulfide system represents a significant advancement of high energy density sulfur-based batteries for future power sources.

  12. Study of a novel porous gel polymer electrolyte based on thermoplastic polyurethane/poly(vinylidene fluoride-co-hexafluoropropylene) by electrospinning technique

    Science.gov (United States)

    Zhou, Ling; Cao, Qi; Jing, Bo; Wang, Xianyou; Tang, Xiaoli; Wu, Na

    2014-10-01

    A novel electrospun gel polymer electrolyte (GPE) consisting of thermoplastic polyurethane (TPU) and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) is prepared and investigated. Its characteristics are investigated by scanning electron microscopy (SEM), thermal analysis (TGA). The GPE shows a maximum ionic conductivity of 4.1 × 10-3 S cm-1 with electrochemical stability up to 5.5 V versus Li+/Li at room temperature. In addition, it shows a first charge-discharge capacity of 168.8 mAh g-1 when the gel polymer electrolyte (GPE) is evaluated in a Li/PE/LiFePO4 cell under 0.1 C-rate at the first cycle. What's more, there is microscale attenuation (1%) in the 30 cycles of charge and discharge tests. The TPU/PVDF-HFP membrane has a high tensile strength (8.4 ± 0.3 MPa) and elongation at break (118.7 ± 0.2)%. With the outstanding electrochemical and mechanical performance, it is very suitable for application in polymer lithium ion batteries.

  13. Physical chemistry studies of ionic conduction gel electrolytes for lithium batteries; Etudes physico-chimiques d'electrolytes gelifies a conduction ionique pour batteries au lithium

    Energy Technology Data Exchange (ETDEWEB)

    Caillon-Caravanier, M.

    2002-12-01

    With the development of new electronic technologies, the research on gel electrolytes basic properties has been widely increased. The use of these materials, produced under thin plastic films, improves the stored energy - battery volume ratio. The ionic gel conductivity, liquid-type, is ensured by the ion migration in the liquid electrolyte incorporated to the polymer network. Thus a preliminary study of liquid phases to be incorporated has been done before the gel investigation. In order to optimize the conductive properties of liquid electrolytes, a simplified model of ionic conductivity has been established. It is based on the ion pair dissociation equilibrium. The ionic mobility is supposed to be inversely proportional to the macroscopic medium viscosity. The liquid electrolytes are then incorporated in the polymer network, based on di-acrylate monomers (DAC) or fluorinated copolymer (PVdF-HFP/SiO{sub 2}). The conductivity loss of the liquid encapsulated phases, more pronounced in the DAC case, is attributed to ion-polymer network interactions, which lead to a decrease of both the concentration and the mobility of free ions in the system. In the case of gel electrolytes DAC based, these interactions are quantified from an ionic transport model, which relies on the hypothesis of a 3D quasi-cubic reticulation. This hypothesis also allows anticipating the network maximal ability to contain the liquid phase. For gel electrolytes PVdF-HFP/SiO{sub 2} based, the kinetic study of the liquid phase absorption has allowed us to optimize the elaboration conditions. The ion-ion, ion-solvent and ion-polymer interactions have. been qualitatively and quantitatively studied by the mean of Raman spectroscopy. The performance of elaborated gel electrolytes is also estimated in cyclability terms towards commercial electrodes for lithium batteries. So the gel behavior has been studied with half-batteries associating a metal lithium electrode to a carbon anode or a lithiated cobalt

  14. Non-aqueous gel polymer electrolyte with phosphoric acid ester and its application for quasi solid-state supercapacitors

    OpenAIRE

    Latoszyńska, Anna A.; Zukowska, Grażyna Zofia; Rutkowska, Iwona A.; Taberna, Pierre-Louis; Simon, Patrice; Kulesza, Pawel J.; Wieczorek, Władysław

    2015-01-01

    International audience; A mechanically-stable non-aqueous proton-conducting gel polymer electrolyte that is based on methacrylate monomers, is considered here for application in solid-state type supercapacitors. An electrochemical cell using activated carbon as active materials and the new gel polymer electrolyte has been characterized at room temperature using cyclic voltammetry, galvanostatic charge–discharge cycle tests as well as impedance spectroscopy. The use of phosphoric acid ester (i...

  15. Dye-Sensitized Solar Cells with Optimal Gel Electrolyte Using the Taguchi Design Method

    OpenAIRE

    Jenn-Kai Tsai; Wen Dung Hsu; Tian-Chiuan Wu; Jia-Song Zhou; Ji-Lin Li; Jian-Hao Liao; Teen-Hang Meen

    2013-01-01

    The Taguchi method was adopted to determine the optimal gel electrolyte used in dye-sensitized solar cells (DSSCs). Since electrolyte is a very important factor in fabrication of high performance and long-term stability DSSCs, to find the optimal composition of gel electrolyte is desired. In this paper, the common ingredients used in the liquid electrolyte were chosen. The ingredients then mixed with cheap ionic liquids and poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) were added...

  16. Composite Gel Polymer Electrolyte Based on Poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) with Modified Aluminum-Doped Lithium Lanthanum Titanate (A-LLTO) for High-Performance Lithium Rechargeable Batteries.

    Science.gov (United States)

    Le, Hang T T; Ngo, Duc Tung; Kalubarme, Ramchandra S; Cao, Guozhong; Park, Choong-Nyeon; Park, Chan-Jin

    2016-08-17

    A composite gel polymer electrolyte (CGPE) based on poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) polymer that includes Al-doped Li0.33La0.56TiO3 (A-LLTO) particles covered with a modified SiO2 (m-SiO2) layer was fabricated through a simple solution-casting method followed by activation in a liquid electrolyte. The obtained CGPE possessed high ionic conductivity, a large electrochemical stability window, and interfacial stability-all superior to that of the pure gel polymer electrolyte (GPE). In addition, under a highly polarized condition, the CGPE effectively suppressed the growth of Li dendrites due to the improved hardness of the GPE by the addition of inorganic A-LLTO/m-SiO2 particles. Accordingly, the Li-ion polymer and Li-O2 cells employing the CGPE exhibited remarkably improved cyclability compared to cells without CGPE. In particular, the CGPE as a protection layer for the Li metal electrode in a Li-O2 cell was effective in blocking the contamination of the Li electrode by oxygen gas or impurities diffused from the cathode side while suppressing the Li dendrites.

  17. Modeling of photocurrent in dye-sensitized solar cells fabricated with PVDF-HFP-based gel-type polymeric solid electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinori, Nishikitani; Takaya, Kubo; Tsuyoshi, Asano [Central Technical Research Laboratory, Nippon Oil Corporation, Naka-ku, Yokohama (Japan)

    2006-05-15

    We discussed photocurrent of dye-sensitized solar cells (DSCs) with model equations of polymeric solid electrolyte (PSE)-based and liquid electrolyte-based DSCs. The short-circuit current (J{sub sc}) was found out to increase even further by either increasing the diffusion coefficient of I{sub 3}{sup -} and/or I{sup -} or decreasing the cell-gap, or both. In particular, the cell-gap dependence of J{sub sc} indicates clearly that narrowing the cell-gap is a simple, effective way to increase the J{sub sc}. We also discussed the diffusion coefficient dependence of J{sub sc}. The back electron transfer from TiO{sub 2} to an oxidized dye was taken into account and explained the diffusion coefficient dependence of J{sub sc} well. (authors)

  18. Stable Lithium Deposition Generated from Ceramic-Cross-Linked Gel Polymer Electrolytes for Lithium Anode.

    Science.gov (United States)

    Tsao, Chih-Hao; Hsiao, Yang-Hung; Hsu, Chun-Han; Kuo, Ping-Lin

    2016-06-22

    In this work, a composite gel electrolyte comprising ceramic cross-linker and poly(ethylene oxide) (PEO) matrix is shown to have superior resistance to lithium dendrite growth and be applicable to gel polymer lithium batteries. In contrast to pristine gel electrolyte, these nanocomposite gel electrolytes show good compatibility with liquid electrolytes, wider electrochemical window, and a superior rate and cycling performance. These silica cross-linkers allow the PEO to form the lithium ion pathway and reduce anion mobility. Therefore, the gel not only features lower polarization and interfacial resistance, but also suppresses electrolyte decomposition and lithium corrosion. Further, these nanocomposite gel electrolytes increase the lithium transference number to 0.5, and exhibit superior electrochemical stability up to 5.0 V. Moreover, the lithium cells feature long-term stability and a Coulombic efficiency that can reach 97% after 100 cycles. The SEM image of the lithium metal surface after the cycling test shows that the composite gel electrolyte with 20% silica cross-linker forms a uniform passivation layer on the lithium surface. Accordingly, these features allow this gel polymer electrolyte with ceramic cross-linker to function as a high-performance lithium-ionic conductor and reliable separator for lithium metal batteries.

  19. Cheap glass fiber mats as a matrix of gel polymer electrolytes for lithium ion batteries.

    Science.gov (United States)

    Zhu, Yusong; Wang, Faxing; Liu, Lili; Xiao, Shiyin; Yang, Yaqiong; Wu, Yuping

    2013-11-12

    Lithium ion batteries (LIBs) are going to play more important roles in electric vehicles and smart grids. The safety of the current LIBs of large capacity has been remaining a challenge due to the existence of large amounts of organic liquid electrolytes. Gel polymer electrolytes (GPEs) have been tried to replace the organic electrolyte to improve their safety. However, the application of GPEs is handicapped by their poor mechanical strength and high cost. Here, we report an economic gel-type composite membrane with high safety and good mechanical strength based on glass fiber mats, which are separator for lead-acid batteries. The gelled membrane exhibits high ionic conductivity (1.13 mS cm(-1)), high Li(+) ion transference number (0.56) and wide electrochemical window. Its electrochemical performance is evaluated by LiFePO4 cathode with good cycling. The results show this gel-type composite membrane has great attraction to the large-capacity LIBs requiring high safety with low cost.

  20. Cheap glass fiber mats as a matrix of gel polymer electrolytes for lithium ion batteries

    Science.gov (United States)

    Zhu, Yusong; Wang, Faxing; Liu, Lili; Xiao, Shiyin; Yang, Yaqiong; Wu, Yuping

    2013-11-01

    Lithium ion batteries (LIBs) are going to play more important roles in electric vehicles and smart grids. The safety of the current LIBs of large capacity has been remaining a challenge due to the existence of large amounts of organic liquid electrolytes. Gel polymer electrolytes (GPEs) have been tried to replace the organic electrolyte to improve their safety. However, the application of GPEs is handicapped by their poor mechanical strength and high cost. Here, we report an economic gel-type composite membrane with high safety and good mechanical strength based on glass fiber mats, which are separator for lead-acid batteries. The gelled membrane exhibits high ionic conductivity (1.13 mS cm-1), high Li+ ion transference number (0.56) and wide electrochemical window. Its electrochemical performance is evaluated by LiFePO4 cathode with good cycling. The results show this gel-type composite membrane has great attraction to the large-capacity LIBs requiring high safety with low cost.

  1. Composite gel polymer electrolyte for lithium ion batteries

    Science.gov (United States)

    Naderi, Roya

    Composite gel polymer electrolyte (CGPE) films, consisting of poly (vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) as the membrane, DMF and PC as solvent and plasticizing agent, mixture of charge modified TiO2 and SiO 2 nano particles as ionic conductors, and LiClO4+LiPF 6 as lithium salts were fabricated. Following the work done by Li et al., CGPE was coated on an O2-plasma treated trilayer polypropylene-polyethylene-polypropylene membrane separator using solution casting technique in order to improve the adhesive properties of gel polymer electrolyte to the separator membrane and its respective ionic conductivity due to decreasing the bulk resistance. In acidic CGPE with, the mixture of acid treated TiO2 and neutral SiO2 nano particles played the role of the charge modified nano fillers with enhanced hydroxyl groups. Likely, the mixture of neutral TiO 2 nano particles with basic SiO2 prepared through the hydrolization of tetraethyl orthosilicate (TEOS) provided a more basic environment due to the residues of NH4OH (Ammonium hydroxide) catalyst. The O2 plasma treated separator was coated with the solution of PVDF-HFP: modified nano fillers: Organic solvents with the mixture ratio of 0.1:0.01:1. After the evaporation of the organic solvents, the dried coated separator was soaked in PC-LiClO4+LiPF6 in EC: DMC:DEC (4:2:4 in volume) solution (300% wt. of PVDF-HFP) to form the final CGPE. Lim et al. has reported the enhanced ionic conductivity of 9.78*10-5 Scm-1 in an acidic composite polystyrene-Al2O3 solid electrolyte system with compared to that of basic and neutral in which the ionic conductivity undergoes an ion hopping process in solid interface rather than a segmental movement of ions through the plasticized polymer chain . Half-cells with graphite anode and Li metal as reference electrode were then assembled and the electrochemical measurements and morphology examinations were successfully carried out. Half cells demonstrated a considerable change in their

  2. Poly(methyl methacrylate-acrylonitrile-ethyl acrylate) terpolymer based gel electrolyte for LiNi0.5Mn1.5O4 cathode of high voltage lithium ion battery

    Science.gov (United States)

    Sun, Ping; Liao, Youhao; Xie, Huili; Chen, Tingting; Rao, Mumin; Li, Weishan

    2014-12-01

    A novel gel polymer electrolyte (GPE), based on poly(methyl methacrylate-acrylonitrile-ethyl acrylate) (P(MMA-AN-EA)) terpolymer, is designed to match LiNi0.5Mn1.5O4 cathode of 5 V lithium ion battery. The performances of the synthesized P(MMA-AN-EA) terpolymer and the corresponding membrane and GPE are investigated by scanning electron microscope, energy dispersive spectroscopy, nuclear magnetic resonance spectra, Fourier transform infrared spectra, thermogravimetric analyzer, electrochemical impedance spectroscopy, linear sweep voltammetry, and charge/discharge test. It is found that the pore structure of P(MMA-AN-EA) membrane is affected by the dose of pore forming agent, polyethylene glycol (PEG400). The membrane with 3 wt% PEG400 presents the best pore structure, in which pores are dispersed uniformly and interconnected, and exhibits the largest electrolyte uptake, resulting in the highest ionic conductivity of 3.82 × 10-3 S cm-1 for the corresponding GPE at room temperature. The GPE has improved compatibility with lithium anode and is electrochemically stable up to 5.2 V (vs. Li/Li+). The high voltage LiNi0.5Mn1.5O4 cathode using the resulting GPE exhibits excellent cyclic stability, maintaining 97.9% of its initial discharge capacity after 100 cycles compared to that of 79.7% for the liquid electrolyte at 0.5 C.

  3. Ionic conductance behavior of polymeric gel electrolyte containing ionic liquid mixed with magnesium salt

    Science.gov (United States)

    Morita, Masayuki; Shirai, Takahiro; Yoshimoto, Nobuko; Ishikawa, Masashi

    A new polymeric gel electrolyte system conducting magnesium ion has been proposed. The gel electrolytes consisted of poly(ethylene oxide)-modified polymethacrylate (PEO-PMA) dissolving ionic liquid mixed with magnesium salt, Mg[(CF 3SO 2) 2N] 2. The polymeric gel films were self-standing, transparent and flexible with enough mechanical strength. The ionic conductance and the electrochemical properties of the gel films were investigated. Thermal analysis results showed that the polymeric gel is homogeneous and amorphous over a wide temperature range. The highest conductivity, 1.1 × 10 -4 S cm -1 at room temperature (20 °C), was obtained for the polymeric gel containing 50 wt.% of the ionic liquid in which the content of the magnesium salt was 20 mol%. The dc polarization of a Pt/Mg cell using the polymeric gel electrolyte proved that the magnesium ion (Mg 2+) is mobile in the present polymeric system.

  4. Electrical and electrochemical properties of magnesium ion conducting composite gel polymer electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, G P; Hashmi, S A [Department of Physics and Astrophysics, University of Delhi, Delhi-110007 (India); Agrawal, R C, E-mail: sahashmi@physics.du.ac.i [School of Studies in Physics, Pt. Ravishankar Shukla University, Raipur-492010, Chhattisgarh (India)

    2010-06-30

    The effect of micro- and nano-sized MgO and nano-sized SiO{sub 2} dispersion on the electrical and electrochemical properties of poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) based Mg{sup 2+} ion conducting gel polymer electrolyte has been investigated. The gel electrolytes have been characterized using electrical conductivity, cationic transport number (t{sub +}) measurements and cyclic voltammetry. A two-maxima feature has been observed in the 'conductivity versus composition' curve at {approx}3 wt% and 10-15 wt% of the filler contents. The highest conductivity has been obtained for the SiO{sub 2} dispersed gel electrolyte of {approx}1 x 10{sup -2} S cm{sup -1} for 3 wt% and {approx}9 x 10{sup -3} S cm{sup -1} at 15 wt% content. The value of 't{sub +}' is found to be enhanced substantially with increasing amount of MgO (both micro- and nanoparticles), whereas in the case of SiO{sub 2} dispersion the value does not increase substantially. The highest 't{sub +}' value of {approx}0.44 has been obtained for the addition of 10 wt% MgO nanoparticles. The enhancement in 't{sub +}' is explained on the basis of the formation of space-charge regions due to the presence of MgO : Mg{sup 2+}-like species, which supports Mg{sup 2+} ion motion. A substantial increase in the amount of anodic and cathodic peak currents is observed due to the addition of nano-sized MgO particles in the gel polymer electrolyte, whereas in the cases of micrometre-sized MgO and nano-sized SiO{sub 2} the enhancement is not significant. The enhancement in conductivity in SiO{sub 2} dispersed nanocomposite gel electrolyte is predominantly due to anionic motion.

  5. Hydroponics gel as a new electrolyte gelling agent for alkaline zinc-air cells

    Science.gov (United States)

    Othman, R.; Basirun, W. J.; Yahaya, A. H.; Arof, A. K.

    The viability of hydroponics gel as a new alkaline electrolyte gelling agent is investigated. Zinc-air cells are fabricated employing 12 wt.% KOH electrolyte immobilised with hydroponics gel. The cells are discharged at constant currents of 5, 50 and 100 mA. XRD and SEM analysis of the anode plates after discharge show that the failure mode is due to the formation of zinc oxide insulating layers and not due to any side reactions between the gel and the plate or the electrolyte.

  6. Dye-Sensitized Solar Cells with Optimal Gel Electrolyte Using the Taguchi Design Method

    Directory of Open Access Journals (Sweden)

    Jenn-Kai Tsai

    2013-01-01

    Full Text Available The Taguchi method was adopted to determine the optimal gel electrolyte used in dye-sensitized solar cells (DSSCs. Since electrolyte is a very important factor in fabrication of high performance and long-term stability DSSCs, to find the optimal composition of gel electrolyte is desired. In this paper, the common ingredients used in the liquid electrolyte were chosen. The ingredients then mixed with cheap ionic liquids and poly(vinylidenefluoride-co-hexafluoropropylene (PVDF-HFP were added to form colloidal electrolyte (gel. The optimal composition of each materials in the gel electrolyte determined by Taguchi method consists of 0.03 M I2, 0.15 M KI, 0.6 M LiI, 0.5 M 4-tertbutylpyridine (TBP, and 10% PVDF-HFP dissolved in the acetonitrile and 3-methoxypropionitrile (MPN solution with volume ratio of 2 : 1. The short circuit current density of 14.11 mA/cm2, the conversion efficiency (η of 5.52%, and the lifetime of over 110 days were observed for the dye-sensitized solar cell assembled with optimal gel electrolyte. The lifetime increases 10 times when compared with the conventional dye-sensitized solar cell assembled with liquid electrolyte.

  7. Gel polymer electrolyte lithium-ion cells with improved low temperature performance

    Science.gov (United States)

    Smart, M. C.; Ratnakumar, B. V.; Behar, A.; Whitcanack, L. D.; Yu, J.-S.; Alamgir, M.

    For a number of NASA's future planetary and terrestrial applications, high energy density rechargeable lithium batteries that can operate at very low temperature are desired. In the pursuit of developing Li-ion batteries with improved low temperature performance, we have also focused on assessing the viability of using gel polymer systems, due to their desirable form factor and enhanced safety characteristics. In the present study we have evaluated three classes of promising liquid low-temperature electrolytes that have been impregnated into gel polymer electrolyte carbon-LiMn 2O 4-based Li-ion cells (manufactured by LG Chem. Inc.), consisting of: (a) binary EC + EMC mixtures with very low EC-content (10%), (b) quaternary carbonate mixtures with low EC-content (16-20%), and (c) ternary electrolytes with very low EC-content (10%) and high proportions of ester co-solvents (i.e., 80%). These electrolytes have been compared with a baseline formulation (i.e., 1.0 M LiPF 6 in EC + DEC + DMC (1:1:1%, v/v/v), where EC, ethylene carbonate, DEC, diethyl carbonate, and DMC, dimethyl carbonate). We have performed a number of characterization tests on these cells, including: determining the rate capacity as a function of temperature (with preceding charge at room temperature and also at low temperature), the cycle life performance (both 100% DOD and 30% DOD low earth orbit cycling), the pulse capability, and the impedance characteristics at different temperatures. We have obtained excellent performance at low temperatures with ester-based electrolytes, including the demonstration of >80% of the room temperature capacity at -60 °C using a C/20 discharge rate with cells containing 1.0 M LiPF 6 in EC + EMC + MB (1:1:8%, v/v/v) (MB, methyl butyrate) and 1.0 M LiPF 6 in EC + EMC + EB (1:1:8%, v/v/v) (EB, ethyl butyrate) electrolytes. In addition, cells containing the ester-based electrolytes were observed to support 5 C pulses at -40 °C, while still maintaining a voltage >2.5 V at

  8. Magnesium ion-conducting gel polymer electrolytes dispersed with nanosized magnesium oxide

    Science.gov (United States)

    Pandey, G. P.; Agrawal, R. C.; Hashmi, S. A.

    Experimental investigations are performed on novel magnesium ion-conducting gel polymer electrolyte nanocomposites based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP), dispersed with nanosized magnesium oxide (MgO) particles. The nanocomposite materials are in the form of free-standing films. Various physical and electrochemical analyses demonstrate promising characteristics of these films, suitable as electrolytes in rechargeable magnesium batteries. The optimized material with 3 wt.% MgO offers a maximum electrical conductivity of ∼8 × 10 -3 S cm -1 at room temperature (∼25 °C) with good thermal and electrochemical stabilities. The ion/filler-polymer interactions and possible conformational changes in host polymer PVdF-HFP due to the liquid electrolyte entrapment and dispersion of nanosized MgO are examined by Fourier transform infrared (FTIR), X-ray diffraction (XRD) and scanning electron microscopic (SEM) methods. The Mg 2+ ion conduction in the gel film is confirmed from the cyclic voltammetry, impedance spectroscopy and transport number measurements. The Mg 2+ ion transport number (t +) is enhanced substantially and found to have a maximum of ∼0.44 for the addition of 10 wt.% MgO nanoparticles. The enhancement in t + is explained on the basis of the formation of space-charge regions due to the presence of MgO:Mg 2+-like species, that supports Mg 2+ ion motion.

  9. A hybrid PVDF-HFP/nanoparticle gel electrolyte for dye-sensitized solar cell applications

    Science.gov (United States)

    Lee, Yuh-Lang; Shen, Yu-Jen; Yang, Yu-Min

    2008-11-01

    Graphite and TiO2 nanoparticles are used as fillers to prepare a polymer gel electrolyte (PGE) based on I-/I3- and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) for dye-sensitized solar cell (DSSC) applications. Graphite nanoparticles (GNP) were proved to be a more efficient filler than TiO2 in enhancing the charge conductivity of the PGE, decreasing the activation energy for charge transport and inhibiting the charge recombination at the TiO2/electrolyte interface. The energy conversion efficiency of a DSSC fabricated using a PGE containing 0.25 wt% of GNP can be increased from 4.69% (without filler) to 6.04%, close to that of a liquid system obtained in this work.

  10. A thermal and electrochemical properties research on gel polymer electrolyte membrane of lithium ion battery

    Science.gov (United States)

    Li, Libo; Ma, Yue; Wang, Wentao; Xu, Yanping; You, Jun; Zhang, Yonghong

    2016-12-01

    N-methyl-N-propyl-piperidin-bis(trifluoromethylsulfonyl)imide/bis(trifluoromethylsulfonyl) imide lithium base/polymethyl methacrylate(PP13TFSI/LiTFSI/PMMA) gel polymer electrolyte (GPE) membrane was prepared by in situ polymerization. The physical and chemical properties were comprehensively discussed. The decomposition characteristics were emphasized by thermogravimetric (TG-DTG) method in the nitrogen atmosphere at the different heating rates of 5, 10, 15 and 20 °C min-1, respectively. The activation energy was calculated with the iso-conversional methods of Ozawa and Kissinger, Friedman, respectively, and the Coats-Redfern methods were adopted to employ the detailed mechanism of the electrolyte membrane. The equation f(α)=3/2[(1-α)1/3-1] was quite an appropriate kinetic mechanisms to describe the thermal decomposition process with an activation energy (Eα) of 184 kJ/mol and a pre-exponential factor (A) of 1.894×1011 were obtained.

  11. A biodegradable gel electrolyte for use in high-performance flexible supercapacitors.

    Science.gov (United States)

    Moon, Won Gyun; Kim, Gil-Pyo; Lee, Minzae; Song, Hyeon Don; Yi, Jongheop

    2015-02-18

    Despite the significant advances in solid polymer electrolytes used for supercapacitors, intractable problems including poor ionic conductivity and low electrochemical performance limit the practical applications. Herein, we report a facile approach to synthesize a NaCl-agarose gel electrolyte for use in flexible supercapacitors. The as-prepared agarose hydrogel consists of a three-dimensional chemically interconnected agarose backbone and oriented interparticular submicropores filled with water. The interconnected agarose matrix acts as a framework that provides mechanical stability to the gel electrolyte and hierarchical porous networks for optimized ion transport. The developed pores with the water filler provide an efficient ionic pathway to the storage sites of electrode. With these properties, the gel electrolyte enables the supercapacitor to have a high specific capacitance of 286.9 F g(-1) and a high rate capability that is 80% of specific capacitance obtained in the case of a liquid electrolyte at 100 mV s(-1). In addition, attributed to the simple procedure and its components, the gel electrolyte is highly scalable, cost-effective, safe, and nontoxic. Thus, the developed gel electrolyte has the potential for use in various energy storage and delivery systems.

  12. A study on PVDF-HFP gel polymer electrolyte for lithium-ion batteries

    Science.gov (United States)

    Liu, W.; Zhang, X. K.; Wu, F.; Xiang, Y.

    2017-06-01

    In this paper, poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) gel polymer electrolyte was fabricated via solvent casting method in order to improve the performance of the lithium-ion batteries. By comparing the physical and electrochemical properties of PVDF-HFP gel polymer electrolyte with three different proportions, the optimization of the PVDF-HFP gel polymer electrolyte was obtained: 10wt% PVDF-HFP - 80wt% tetrahydrofuran (THF) / acetone - 10wt% 1mol L-1 lithium perchlorate (LiClO4) in elthylene carbonate (EC) and diethyl carbonate (DEC). The optimized PVDF-HFP gel polymer electrolyte displayed a high conductivity of 1.06×10-3 S cm-1 at room temperature, a high lithium transference number of 0.36 and a good thermal stability within 100°C. Moreover, the discharge specific capacity was 135.1 mAh g-1, and the charge / discharge efficiency was 99.1% at 0.1C rate. Therefore, the fabricated PVDF-HFP gel polymer electrolyte was an effective gel polymer electrolyte to be applied on lithium-ion batteries.

  13. Stability of the Gel Electrolyte PAN : EC : PC : LICF3SO3 towards Lithium

    DEFF Research Database (Denmark)

    Perera, Kumudu; Skaarup, Steen; West, K.

    2006-01-01

    The stability of the gel electrolyte consisting of polyacrylonitrile (PAN), ethylene carbonate (EC), propylene carbonate (PC) and lithium trifluoromethanesulfonate (LiCF3SO3 – LiTF) towards metallic lithium was investigated using the time evolution of impedance plots. Symmetric cells of the form Li...... / PAN : EC : PC: LiTF / Li were assembled and impedance data were collected at room temperature for one week. A clear indication of growth of a resistive layer could be seen. The electrolyte resistance remained constant. The growth of the passivation layer became constant after first two days....... These observations suggest that this gel electrolyte is suitable for use with metallic lithium....

  14. Gel Polymer Electrolytes Containing Anion-Trapping Boron Moieties for Lithium-Ion Battery Applications.

    Science.gov (United States)

    Shim, Jimin; Lee, Ji Su; Lee, Jin Hong; Kim, Hee Joong; Lee, Jong-Chan

    2016-10-04

    Gel polymer electrolytes (GPEs) based on semi-interpenetrating polymer network (IPN) structure for lithium-ion batteries were prepared by mixing boron-containing crosslinker (BC) composed of ion-conducting ethylene oxide (EO) chains, crosslinkable methacrylate group, and anion-trapping boron moiety with poly(vinylidene fluoride) (PVDF) followed by ultraviolet light-induced curing process. Various physical and electrochemical properties of the GPEs were systematically investigated by varying the EO chain length and boron content. Dimensional stability at high temperature without thermal shrinkage, if any, was observed due to the presence of thermally stable PVDF in the GPEs. GPE having 80 wt% of BC and 20 wt% of PVDF exhibited an ionic conductivity of 4.2 mS cm(-1) at 30 (o)C which is one order of magnitude larger than that of the liquid electrolyte system containing the commercial Celgard separator (0.4 mS cm(-1)) owing to the facile electrolyte uptake ability of EO chain and anion-trapping ability of boron moiety. As a result, lithium-ion battery cell prepared using the GPE with BC showed an excellent cycle performance at 1.0 C maintaining 87 % of capacity during 100 cycles.

  15. Microporous polymer electrolyte based on PVDF-PEO

    Institute of Scientific and Technical Information of China (English)

    LI Jian; XI Jingyu; SONG Qing; TANG Xiaozhen

    2005-01-01

    @@ Since Wright et al.[1] found that the complex of PEO/alkali metals salt had the ability of ionic conductivity in 1973, in-depth studies have been carried out about various polymer electrolytes, which were applied to replacing the liquid electrolytes in lithium ion battery[2,3]. At present, polymer electrolytes mainly include three kinds: dry polymer electrolytes, gel polymer electrolytes and microporous polymer electrolytes.

  16. Tubular array, dielectric, conductivity and electrochemical properties of biodegradable gel polymer electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Sudhakar, Y.N. [Department of Chemistry, Manipal Institute of Technology, Manipal, Karnataka (India); Selvakumar, M., E-mail: chemselva78@gmail.com [Department of Chemistry, Manipal Institute of Technology, Manipal, Karnataka (India); Bhat, D. Krishna [Department of Chemistry, National Institute of Technology Karnataka, Surathkal, Mangalore (India)

    2014-02-15

    Highlights: • A new finding of tubular array of 10–20 μm in length and 1–2 μm in thickness of gel polymer electrolyte (GPE) having 2.2 × 10{sup −3} S cm{sup −1} conductivity is reported. • Thermal and electrochemical characterizations of GPEs show good interaction among the polymer, plasticizer and salt. • GPE based supercapacitor demonstrates high capacitance of 186 F g{sup −1}. • Low temperature studies did not influence much on capacitance values obtained from AC impedance studies. • Charge–discharge exhibits high capacity with excellent cyclic stability and energy density. -- Abstract: A supercapacitor based on a biodegradable gel polymer electrolyte (GPE) has been fabricated using guar gum (GG) as the polymer matrix, LiClO{sub 4} as the doping salt and glycerol as the plasticizer. The scanning electron microscopy (SEM) images of the gel polymer showed an unusual tubular array type surface morphology. FTIR, DSC and TGA results of the GPE indicated good interaction between the components used. Highest ionic conductivity and lowest activation energy values were 2.2 × 10{sup −3} S cm{sup −1} and 0.18 eV, respectively. Dielectric studies revealed ionic behavior and good capacitance with varying frequency of the GPE system. The fabricated supercapacitor showed a maximum specific capacitance value of 186 F g{sup −1} using cyclic voltammetry. Variation of temperature from 273 K to 293 K did not significantly influence the capacitance values obtained from AC impedance studies. Galvanostatic charge–discharge study of supercapacitor indicated that the device has good stability, high energy density and power density.

  17. Magnesium ion-conducting gel polymer electrolytes dispersed with nanosized magnesium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, G.P. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Solid State Ionics Research Laboratory, School of Studies in Physics, Pt. Ravishankar Shukla University, Raipur 492010, C.G. (India); Agrawal, R.C. [Solid State Ionics Research Laboratory, School of Studies in Physics, Pt. Ravishankar Shukla University, Raipur 492010, C.G. (India); Hashmi, S.A. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2009-05-15

    Experimental investigations are performed on novel magnesium ion-conducting gel polymer electrolyte nanocomposites based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP), dispersed with nanosized magnesium oxide (MgO) particles. The nanocomposite materials are in the form of free-standing films. Various physical and electrochemical analyses demonstrate promising characteristics of these films, suitable as electrolytes in rechargeable magnesium batteries. The optimized material with 3 wt.% MgO offers a maximum electrical conductivity of {proportional_to}8 x 10{sup -3} S cm{sup -1} at room temperature ({proportional_to}25 C) with good thermal and electrochemical stabilities. The ion/filler-polymer interactions and possible conformational changes in host polymer PVdF-HFP due to the liquid electrolyte entrapment and dispersion of nanosized MgO are examined by Fourier transform infrared (FTIR), X-ray diffraction (XRD) and scanning electron microscopic (SEM) methods. The Mg{sup 2+} ion conduction in the gel film is confirmed from the cyclic voltammetry, impedance spectroscopy and transport number measurements. The Mg{sup 2+} ion transport number (t{sub +}) is enhanced substantially and found to have a maximum of {proportional_to}0.44 for the addition of 10 wt.% MgO nanoparticles. The enhancement in t{sub +} is explained on the basis of the formation of space-charge regions due to the presence of MgO:Mg{sup 2+}-like species, that supports Mg{sup 2+} ion motion. (author)

  18. Electrical and electrochemical studies of poly(vinylidene fluoride)-clay nanocomposite gel polymer electrolytes for Li-ion batteries

    Science.gov (United States)

    Deka, M.; Kumar, A.

    A study is conducted on the electrical and electrochemical properties of nanocomposite polymer electrolytes based on intercalation of poly(vinylidene fluoride) (PVdF) polymer into the galleries of organically modified montmorillonite (MMT) clay. A solution intercalation technique is employed for nanocomposite formation with varying clay loading from 0 to 4 wt.%. X-ray diffraction results show the β phase formation of PVdF on intercalation. Transmission electron microscopy reveals the formation of partially exfoliated nanocomposites. The nanocomposites are soaked with 1 M LiClO 4 in a 1:1 (v/v) solution of propylene carbonate (PC) and diethyl carbonate (DEC) to obtain the required gel electrolytes. The structural conformation of the nanocomposite electrolytes is examined by Fourier transform infrared spectroscopy analysis. Examination with a.c. impedance spectroscopy reveals that the ionic conductivity of the nanocomposite gel polymer electrolytes increases with increase in clay loading and attains a maximum value of 2.3 × 10 -3 S cm -1 for a 4 wt.% clay loading at room temperature. The same composition exhibits enhancement in the electrochemical and interfacial properties as compared with that of a clay-free electrolyte system.

  19. Morphology, thermal, electrical and electrochemical stability of nano aluminium-oxide-filled polyvinyl alcohol composite gel electrolyte

    Indian Academy of Sciences (India)

    Navin Chand; Neelesh Rai; S L Agrawal; S K Patel

    2011-12-01

    In the present work, an attempt has been made to develop nano aluminium oxide (Al2O3)-filled polyvinyl alcohol (PVA) composite gel electrolytes. Surface morphological studies, thermal behaviour, electrochemical stability and electrical characterization of these composite gel electrolytes have been performed. An increase in the concentration of Al2O3 in composite gel electrolytes increases the amorphous characteristics of pure PVA. Bulk conductivity of composite gel electrolytes increases by an order of magnitude on addition of a nano filler. Maximum conductivity of 5.81 × 10-2 S/cm is observed for 6 wt% Al2O3-filled polymer gel composite electrolytes. Temperature dependence of electrical conductivity shows a combination of Arrhenius and Vogel–Tamman–Fulcher (VTF) nature. Maximum current stability during oxidation and reduction cycle is noticed for 6 wt% Al2O3-filled PVA composite electrolyte, viz. ±1.65 V.

  20. In situ Poly(methyl methacrylate)/Graphene Composite Gel Electrolytes for Highly Stable Dye-Sensitized Solar Cells.

    Science.gov (United States)

    Kang, Yu-il; Moon, Jun Hyuk

    2015-11-01

    Dye-sensitized solar cells (DSCs) with long-term stability are produced using polymer-gel electrolytes (PGEs). In this study, we introduce the formation of PGEs using in situ gelation with poly(methyl methacrylate) (PMMA) particles and graphene fillers that are pre-deposited on the counter electrodes. We obtain a high concentration PMMA-based PGEs (i.e., over 10 wt%). A DSC composed of a PMMA/graphene composite PGEs exhibits an 8.49% photon-to-electric conversion efficiency, which is comparable to conventional liquid electrolyte DSCs. This finding is attributed to increased ion diffusivity and conductivity of the PMMA-based PGEs resulting from the incorporation of graphene nanofillers. The PMMA-based PGE DSCs exhibit highly stable long-term efficiencies, maintaining up to 90% of their initial efficiency during thermal soaking, whereas the efficiencies of liquid electrolyte cells decrease significantly, by up to 60%.

  1. Honeycomb-like porous gel polymer electrolyte membrane for lithium ion batteries with enhanced safety

    Science.gov (United States)

    Zhang, Jinqiang; Sun, Bing; Huang, Xiaodan; Chen, Shuangqiang; Wang, Guoxiu

    2014-08-01

    Lithium ion batteries have shown great potential in applications as power sources for electric vehicles and large-scale energy storage. However, the direct uses of flammable organic liquid electrolyte with commercial separator induce serious safety problems including the risk of fire and explosion. Herein, we report the development of poly(vinylidene difluoride-co-hexafluoropropylene) polymer membranes with multi-sized honeycomb-like porous architectures. The as-prepared polymer electrolyte membranes contain porosity as high as 78%, which leads to the high electrolyte uptake of 86.2 wt%. The PVDF-HFP gel polymer electrolyte membranes exhibited a high ionic conductivity of 1.03 mS cm-1 at room temperature, which is much higher than that of commercial polymer membranes. Moreover, the as-obtained gel polymer membranes are also thermally stable up to 350°C and non-combustible in fire (fire-proof). When applied in lithium ion batteries with LiFePO4 as cathode materials, the gel polymer electrolyte demonstrated excellent electrochemical performances. This investigation indicates that PVDF-HFP gel polymer membranes could be potentially applicable for high power lithium ion batteries with the features of high safety, low cost and good performance.

  2. Sol-Gel Electrolytes Incorporated by Lanthanide Luminescent Materials and Their Photophysical Properties

    Science.gov (United States)

    Yu, Chufang; Zhang, Zhengyang; Fu, Meizhen; Gao, Jinwei; Zheng, Yuhui

    2017-10-01

    A group of silica gel electrolytes with lanthanide luminescent hybrid materials were assembled and investigated. Photophysical studies showed that terbium and europium hybrids displayed characteristic green and red emissions within the electrolytes. The influence of different concentration of the lanthanide hybrids on the electrochemical behavior of a gelled electrolyte valve-regulated lead-acid battery were studied through cyclic voltammograms, electrochemical impedance spectroscopy, water holding experiments and mobility tests. The morphology and particle size were analyzed by scanning electron microscopy. The results proved that lanthanide (Tb3+/Eu3+) luminescent materials are effective additives which will significantly improve the electrochemical properties of lead-acid batteries.

  3. Polymeric gel electrolyte containing alkyl phosphate for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Morita, Masayuki; Niida, Yoshihiro; Yoshimoto, Nobuko [Department of Applied Chemistry and Chemical Engineering, Yamaguchi University, 2-16-1 Tokiwadai, Ube 755-8611 (Japan); Adachi, Kazuyuki [Research Laboratory, Kyusyu Electric Power Company, 2-1-47 Shiobaru, Minami-ku, Fukuoka 815-8520 (Japan)

    2005-08-26

    A nonflammable polymeric gel electrolyte film has been developed for rechargeable lithium battery systems. The gel film consists of poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP) swollen with LiPF{sub 6} solution of a ternary solvent containing nonflammable trimethyl phosphate (TMP). The addition of TMP to mixed ethylene carbonate plus diethyl carbonate (EC+DEC) solvent prevented the LiPF{sub 6} salt from the thermal decomposition. The LiPF{sub 6} solutions containing 20vol% or higher content of TMP were fire-retardant. High ionic conductivity was obtained for both the liquid and the gel electrolyte systems containing 55vol% of TMP in the liquid components: 7.1x10{sup -3}Scm{sup -1} for the liquid and 2.9x10{sup -3}Scm{sup -1} for the gel electrolytes at 20{sup o}C. A wide potential window (-0.5 to 4.5V versus Li/Li{sup +}) and the redox activity of the electrode materials were established for the gel electrolyte containing TMP. (author)

  4. Evaluation of interactive effects on the ionic conduction properties of polymer gel electrolytes.

    Science.gov (United States)

    Saito, Yuria; Okano, Miki; Kubota, Keigo; Sakai, Tetsuo; Fujioka, Junji; Kawakami, Tomohiro

    2012-08-23

    Ionic mobility of electrolyte materials is essentially determined by the nanoscale interactions, the ion-ion interactions and ion-solvent interactions. We quantitatively evaluated the interactive situation of the lithium polymer gel electrolytes through the measurements of ionic conductivity and diffusion coefficients of the mobile species of the lithium polymer electrolytes. The interactive force between the cation and anion in the gel depended on the mixing ratio of the binary solvent, ethylene carbonate plus dimethyl carbonate (EC/DMC). The gel with the solvent (3:7 EC:DMC) showed minimal cation-anion interaction, which is the cause of the highest ionic mobility compared with those of the other gels with different solvents. This suggests that the cation-anion interaction does not simply depend on the dielectric constant of the solvent but is associated with the solvation condition of the lithium. In the case of the gel with the 3:7 EC/DMC solvent, most of the EC species strongly coordinate to a lithium ion, forming the stable solvated lithium, Li(EC)(3)(+), and there are no residual EC species for exchange with them. As a result, the solvating EC species would be a barrier that restricts the anion attack to the lithium leading to the smallest cation-anion interaction. On the other hand, interaction between the cation and polar sites, hydroxyl and oxygen groups of ether of the polyvinyl butyral (PVB) and polyethylene oxide (PEO) polymer, respectively, in the gels was another dominant factor responsible for cation mobility. It increased with increasing polar site concentration per lithium. In case of the PVB gels, cation-anion interaction increased with an increasing polymer fraction of the gel contrary to the independent feature of PEO gels with the change of the polymer fraction. This indicates that the cation-anion interaction is associated with the polymer structure of the gel characterized by the kind and configuration of polar groups, molecular weight, and

  5. Flexible all-solid-state supercapacitors based on graphene/carbon black nanoparticle film electrodes and cross-linked poly(vinyl alcohol)-H2SO4 porous gel electrolytes

    Science.gov (United States)

    Fei, Haojie; Yang, Chongyang; Bao, Hua; Wang, Gengchao

    2014-11-01

    Flexible all-solid-state supercapacitors (SCs) are fabricated using graphene/carbon black nanoparticle (GCB) film electrodes and cross-linked poly(vinyl alcohol)-H2SO4 porous gel electrolytes (gPVAP-H2SO4). The GCB composite films, with carbon black (CB) nanoparticles uniformly distributed in the graphene nanosheets, greatly improve the active surface areas and ion transportation of pristine graphene film. The porous structure of as-prepared gPVAP-H2SO4 membrane improves the equilibrium swelling ratio in electrolyte and provides interconnected ion transport channels. The chemical crosslinking solves the fluidity problem of PVA-H2SO4 gel electrolyte at high temperature. As-fabricated GCB//gPVAP(20)-H2SO4//GCB flexible SC displays an increased specific capacitance (144.5 F g-1 at 0.5 A g-1) and a higher specific capacitance retention (67.9% from 0.2 to 4 A g-1). More importantly, the flexible SC possesses good electrochemical performance at high temperature (capacitance retention of 78.3% after 1000 cycles at 70 °C).

  6. AC ionic conductivity and DC polarization method of lithium ion transport in PMMA-LiBF4 gel polymer electrolytes

    Science.gov (United States)

    Osman, Z.; Mohd Ghazali, M. I.; Othman, L.; Md Isa, K. B.

    2012-01-01

    Polymethylmethacrylate (PMMA)-based gel polymer electrolytes comprising ethylene carbonate-propylene carbonate (EC/PC) mixed solvent plasticizer and various concentrations of lithium tetrafluoroborate (LiBF4) salt are prepared using a solvent casting technique. Electrical conductivity and transference number measurements were carried out to investigate conductivity and charge transport in the gel polymer electrolytes. The conductivity results show that the ionic conductivity of the samples increases when the amount of salt is increased, however decreases after reaching the optimum value. This result is consistent with the transference number measurements. The conductivity-frequency dependence plots show two distinct regions; i.e. at lower frequencies the conductivity increases with increasing frequency and the frequency independent plateau region at higher frequencies. The temperature-dependence conductivity of the films seems to obey the Arrhenius rule.

  7. Ionic transport studies in PVDF-HFP-PMMA-(PC+DEC)-LiClO4 gel polymer electrolyte

    Science.gov (United States)

    Gohel, Khushbu; Kanchan, D. K.

    2017-05-01

    Poly(vinylidene fluoride-hexafluropropylene)(PVdF-HFP) and Polymethylmethacrylate(PMMA) based gel polymer electrolytes comprising Propylene Carbonate and Diethyl Carbonate mixed plasticizers and different concentrations of Lithium Perchlorate (LiClO4) salt have been prepared using a solvent casting technique. Electrical conductivity and transference number measurements have been carried out by Electrochemical Impedance Spectroscopy in the temperature range 303 K to 363 K and Wagner's Polarization method respectively. The maximum room temperature conductivity of 2.83 ×10-4 S cm-1 has been observed for the gel polymer electrolytes at 7.5 wt% LiClO4. The variation of ac conductivity with frequency has been discussed.

  8. High performance solid-state electric double layer capacitor from redox mediated gel polymer electrolyte and renewable tamarind fruit shell derived porous carbon.

    Science.gov (United States)

    Senthilkumar, S T; Selvan, R Kalai; Melo, J S; Sanjeeviraja, C

    2013-11-13

    The activated carbon was derived from tamarind fruit shell and utilized as electrodes in a solid state electrochemical double layer capacitor (SSEDLC). The fabricated SSEDLC with PVA (polyvinyl alcohol)/H2SO4 gel electrolyte delivered high specific capacitance and energy density of 412 F g(-1) and 9.166 W h kg(-1), respectively, at 1.56 A g(-1). Subsequently, Na2MoO4 (sodium molybdate) added PVA/H2SO4 gel electrolyte was also prepared and applied for SSEDLC, to improve the performance. Surprisingly, 57.2% of specific capacitance (648 F g(-1)) and of energy density (14.4 Wh kg(-1)) was increased while introducing Na2MoO4 as the redox mediator in PVA/H2SO4 gel electrolyte. This improved performance is owed to the redox reaction between Mo(VI)/Mo(V) and Mo(VI)/Mo(IV) redox couples in Na2MoO4/PVA/H2SO4 gel electrolyte. Similarly, the fabricated device shows the excellent capacitance retention of 93% for over 3000 cycles. The present work suggests that the Na2MoO4 added PVA/H2SO4 gel is a potential electrolyte to improve the performance instead of pristine PVA/H2SO4 gel electrolyte. Based on the overall performance, it is strongly believed that the combination of tamarind fruit shell derived activated carbon and Na2MoO4/PVA/H2SO4 gel electrolyte is more attractive in the near future for high performance SSEDLCs.

  9. Effect of chemically modified silicas on the properties of hybrid gel electrolyte for Li-ion batteries

    Science.gov (United States)

    Walkowiak, Mariusz; Zalewska, Aldona; Jesionowski, Teofil; Waszak, Daniel; Czajka, Bogdan

    The aim of the presented work was to perform a preliminary study the physico-chemical properties of hybrid organic-inorganic gel electrolytes for Li-ion batteries based on the PVdF-HFP polymeric matrix and surface modified fumed silicas. Modifications were done by means of the so-called dry method using seven different silanes differing in the nature of the principal functional group: N-2-(aminoethyl)-3-amino propyltrimethoxysilane, 3-glycidoxypropyltrimetoxysilane, 3-mercaptopropyltrimetoxysilane, n-octyltriethoxysilane, 3-(chloropropyl)trimethoxysilane, 3-methacryloxypropyltrimetoxysilane, vinyltrimethoxysilane. The PVdF-HFP gels were prepared according to the so-called Bellcore process (two-step method). Impact of the silicas surface functionality on the degree of crystallinity of the polymeric membranes was studied using the differential scanning calorimetry technique. Applicability of the prepared gel electrolytes for the Li-ion technology was estimated on the basis of specific conductivity measurements. It was shown that modification of the silica surface by most of the silanes causes an increase in the gel specific conductivity by about two orders of magnitude as compared to gel with unmodified silica.

  10. Effect of chemically modified silicas on the properties of hybrid gel electrolyte for Li-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Walkowiak, Mariusz; Waszak, Daniel; Czajka, Bogdan [Central Laboratory of Batteries and Cells, ul. Forteczna 12, 61-362 Poznan (Poland); Zalewska, Aldona [Warsaw University of Technology, Department of Chemistry, ul. Noakowskiego 3, 00-664 Warsaw (Poland); Jesionowski, Teofil [Poznan University of Technology, Institute of Chemical Technology and Engineering, Pl. Marii Sklodowskiej-Curie 2, 60-965 Poznan (Poland)

    2006-09-13

    The aim of the presented work was to perform a preliminary study the physico-chemical properties of hybrid organic-inorganic gel electrolytes for Li-ion batteries based on the PVdF-HFP polymeric matrix and surface modified fumed silicas. Modifications were done by means of the so-called dry method using seven different silanes differing in the nature of the principal functional group: N-2-(aminoethyl)-3-amino propyltrimethoxysilane, 3-glycidoxypropyltrimetoxysilane, 3-mercaptopropyltrimetoxysilane, n-octyltriethoxysilane, 3-(chloropropyl)trimethoxysilane, 3-methacryloxypropyltrimetoxysilane, vinyltrimethoxysilane. The PVdF-HFP gels were prepared according to the so-called Bellcore process (two-step method). Impact of the silicas surface functionality on the degree of crystallinity of the polymeric membranes was studied using the differential scanning calorimetry technique. Applicability of the prepared gel electrolytes for the Li-ion technology was estimated on the basis of specific conductivity measurements. It was shown that modification of the silica surface by most of the silanes causes an increase in the gel specific conductivity by about two orders of magnitude as compared to gel with unmodified silica. (author)

  11. Preparation and Application of Nano-composite Poly(vinyl alcohol) Gel Electrolyte in Electrochemical Capacitor

    Institute of Scientific and Technical Information of China (English)

    陈赟; 谭强强; 徐宇兴

    2012-01-01

    A nano-composite polymer gel electrolyte was prepared using titanium oxide nanowire,poly(vinyl alcohol) (PVA),lithium salt and organic solvent N-methyl-2-pyrrolidone (NMP).The obtained electrolyte has the potential for application in electrochemical capacitor,the PVA in it is in an amorphous state.The ionic conductivities of electrolytes increased after addition of the nanowire,and the electrolyte with 3%(ω) of nanowire exhibited the highest ionic conductivity of 3.2 mS/cm at 20 ℃,as measured by electrochemical impedance spectroscopy.The temperature dependence of the conductivity was found to be in agreement with the Arrhenius equation.Functioning as separator and electrolyte,this nano-composite PVA gel electrolyte was used to assemble the electrochemical capacitor with active carbon film as electrodes.The compositing of nanowire may extend the life of electrochemical capacitors as they keep more than 90% of their capacitance after 5 000 cycles of charging and discharging.

  12. Stable quasi-solid-state dye-sensitized solar cell using ionic gel electrolyte with low molecular mass organogelator

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Li [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huo, Zhipeng, E-mail: zhipenghuo@163.com [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Dai, Songyuan, E-mail: sydai@ncepu.edu.cn [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Beijing Key Lab of Novel Thin Film Solar Cells, North China Electric Power University, Beijing 102206 (China); Zhu, Jun; Zhang, Changneng; Pan, Xu; Huang, Yang [Key Laboratory of Novel Thin Film Solar Cells, Division of Solar Energy Materials and Engineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Yang, Shangfeng [Hefei National Laboratory for Physical Sciences at Microscale, Department of Materials Science and Engineering, University of Science and Technology of China (USTC), Hefei 230026 (China); Zhang, Bing; Yao, Jianxi [Beijing Key Lab of Novel Thin Film Solar Cells, North China Electric Power University, Beijing 102206 (China)

    2015-02-15

    Long-term stability is essential for the application and commercialization of dye-sensitized solar cells (DSCs). A quasi-solid-state DSC (QS-DSC) with excellent long-term stability is fabricated using ionic gel electrolyte (IGE) with N,N′-methylenebisdodecanamide as low molecular mass organogelator (LMOG). The gel to solution transition temperature (T{sub gel}) of this IGE is 127 °C, well above the working temperature of the device, which contributes to the thermal properties of the IGE and the device. The electrochemical properties of the IGE and the kinetic processes of electron transport and recombination of the QS-DSC are investigated by means of electrochemical impedance spectroscopy (EIS) and controlled intensity modulated photocurrent/photovoltage spectroscopy (IMPS/IMVS). Due to the obstructed diffusion of redox species caused by the network of IGE, the electron recombination at the TiO{sub 2} photoelectrode/electrolyte interface in the QS-DSC is accelerated. More importantly, compared with the ionic liquid electrolyte (ILE) based DSC, the QS-DSC based on the IGE exhibits excellent thermal and light-soaking stabilities during the accelerated aging tests for 1000 h. Especially, there is almost no degradation in the short-circuit current density (J{sub sc}) in the IGE based QS-DSC, while the J{sub sc} of the ILE based DSC decreased to 85–94% of their initial values. - Highlights: • A novel IGE with high T{sub gel} is obtained by using a diamide derivative as LMOG. • The IGE based QS-DSC is very stable during the accelerated aging tests. • The influences of gelation on the electron kinetic processes are investigated.

  13. Improvement of ionic conductivity and performance of quasi-solid-state dye sensitized solar cell using PEO/PMMA gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Aram, E. [Iran Polymer and Petrochemical Institute, 14965/115 Tehran (Iran, Islamic Republic of); Ehsani, M., E-mail: m.ehsani@ippi.ac.ir [Iran Polymer and Petrochemical Institute, 14965/115 Tehran (Iran, Islamic Republic of); Khonakdar, H.A. [Iran Polymer and Petrochemical Institute, 14965/115 Tehran (Iran, Islamic Republic of); Leibniz Institute of Polymer Research, D-01067 Dresden (Germany)

    2015-09-10

    Graphical abstract: Reduced interfacial resistance of a quasi-solid-state dye sensitized solar cell with PEO/PMMA blend gel electrolytes. - Highlights: • A new polymer gel electrolyte containing PEO/PMMA was developed for DSSCs. • Optimization of polymer gel electrolyte was done for dye sensitized solar cell. • The best ionic conductivity was found in PEO/PMMA blend with 10/90 w/w composition. • The DSSC with the PEO/PMMA based electrolyte showed good photovoltaic performance. • Significant stability improvement for quasi-solid state DSSC was obtained. - Abstract: Polymer blend gel electrolytes based on polyethylene oxide (PEO) and poly(methyl methacrylate) (PMMA) as host polymers with various weight ratios, LiI/I{sub 2} as redox couple in electrolyte and 4-tert-butyl pyridine as additive were prepared by solution method. The introduction of PMMA in the PEO gel electrolyte reduced the degree of crystallinity of PEO, which was confirmed by differential scanning calorimetry (DSC). Complexation and ionic conductivity as a function of temperature were investigated with Fourier transform infrared and ionic conductometry, respectively. A good correlation was found between the degree of crystallinity and ionic conductivity. The reduction in crystallinity, governed by blending ratio, led to improvement of ionic conductivity. The best ionic conductivity was attained in PEO/PMMA blend with 10/90 w/w composition. The performance of a quasi-solid-state dye sensitized solar cell using the optimized polymer gel electrolyte was investigated. The optimized system of high ionic conductivity of 7 mS cm{sup −1}, with fill factor of 0.59, short-circuit density of 11.11 mA cm{sup −2}, open-circuit voltage of 0.75 V and the conversion efficiency of 4.9% under air mass 1.5 irradiation (100 mW cm{sup −2}) was obtained. The long-term stability of the dye-sensitized solar cell (DSSC) during 600 h was improved by using PEO/PMMA gel electrolyte relative to a liquid type

  14. Sol-gel derived ceramic electrolyte films on porous substrates

    Energy Technology Data Exchange (ETDEWEB)

    Kueper, Timothy Walter [Univ. of California, Berkeley, CA (United States)

    1992-05-01

    A process for the deposition of sol-gel derived thin films on porous substrates has been developed; such films should be useful for solid oxide fuel cells and related applications. Yttria-stabilized zirconia films have been formed from metal alkoxide starting solutions. Dense films have been deposited on metal substrates and ceramic substrates, both dense and porous, through dip-coating and spin-coating techniques, followed by a heat treatment in air. X-ray diffraction has been used to determine the crystalline phases formed and the extent of reactions with various substrates which may be encountered in gas/gas devices. Surface coatings have been successfully applied to porous substrates through the control of substrate pore size and deposition parameters. Wetting of the substrate pores by the coating solution is discussed, and conditions are defined for which films can be deposited over the pores without filling the interiors of the pores. Shrinkage cracking was encountered in films thicker than a critical value, which depended on the sol-gel process parameters and on the substrate characteristics. Local discontinuities were also observed in films which were thinner than a critical value which depended on the substrate pore size. A theoretical discussion of cracking mechanisms is presented for both types of cracking, and the conditions necessary for successful thin formation are defined. The applicability of these film gas/gas devices is discussed.

  15. Sol-gel derived ceramic electrolyte films on porous substrates

    Energy Technology Data Exchange (ETDEWEB)

    Kueper, T.W.

    1992-05-01

    A process for the deposition of sol-gel derived thin films on porous substrates has been developed; such films should be useful for solid oxide fuel cells and related applications. Yttria-stabilized zirconia films have been formed from metal alkoxide starting solutions. Dense films have been deposited on metal substrates and ceramic substrates, both dense and porous, through dip-coating and spin-coating techniques, followed by a heat treatment in air. X-ray diffraction has been used to determine the crystalline phases formed and the extent of reactions with various substrates which may be encountered in gas/gas devices. Surface coatings have been successfully applied to porous substrates through the control of substrate pore size and deposition parameters. Wetting of the substrate pores by the coating solution is discussed, and conditions are defined for which films can be deposited over the pores without filling the interiors of the pores. Shrinkage cracking was encountered in films thicker than a critical value, which depended on the sol-gel process parameters and on the substrate characteristics. Local discontinuities were also observed in films which were thinner than a critical value which depended on the substrate pore size. A theoretical discussion of cracking mechanisms is presented for both types of cracking, and the conditions necessary for successful thin formation are defined. The applicability of these film gas/gas devices is discussed.

  16. N-Butyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide-PVdF(HFP) gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki-Sub; Park, Seung-Yeob; Yeon, Sun-Hwa; Lee, Huen [Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea)

    2005-09-30

    Ionic liquid-polymer gels were prepared by incorporating N-butyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide (Mor{sub 1,4}TFSI) and poly(vinylidene fluoride)-hexafluoropropylene copolymer (PVdF(HFP)) using three different methods in order to observe the variation of ionic conductivities according to the presence of propylene carbonate (PC) and various weight ratios between Mor{sub 1,4}TFSI and gel polymer electrolyte (GPE). Ionic conductivities for each gel polymer electrolyte were measured with increasing temperature. Ionic conductivities of the GPEs increased with increasing temperature and weight ratio of Mor{sub 1,4}TFSI. In addition, the addition of PC into GPE led to the improvement of ionic conductivities. Thermogravimetric analysis (TGA) showed the suggested gel polymer electrolytes composed of only ionic liquid and polymer were stable up to approximately 400 C. TGA and infrared spectroscopy data indicated that residual PC remains after evaporating PC in a vacuum oven, which did not affect the ionic conductivities. The GPEs containing PC displayed high conductivity (ca. 10{sup -2} S cm{sup -1}) at 60 C. (author)

  17. Stability of the Gel Electrolyte PAN : EC : PC : LICF3SO3 towards Lithium

    DEFF Research Database (Denmark)

    Perera, Kumudu; Dissanayake, M.A.K.L.; Skaarup, Steen;

    2006-01-01

    The stability of the gel electrolyte consisting of polyacrylonitrile (PAN), ethylene carbonate (EC), propylene carbonate (PC) and lithium trifluoromethanesulfonate (LiCF3SO3 – LiTF) towards metallic lithium was investigated using the time evolution of impedance plots. Symmetric cells of the form Li...... / PAN : EC : PC: LiTF / Li were assembled and impedance data were collected at room temperature for one week. A clear indication of growth of a resistive layer could be seen. The electrolyte resistance remained constant. The growth of the passivation layer became constant after first two days...

  18. Effects of TiO2 and TiC Nanofillers on the Performance of Dye Sensitized Solar Cells Based on the Polymer Gel Electrolyte of a Cobalt Redox System.

    Science.gov (United States)

    Venkatesan, Shanmuganathan; Liu, I-Ping; Chen, Li-Tung; Hou, Yi-Chen; Li, Chiao-Wei; Lee, Yuh-Lang

    2016-09-21

    Polymer gel electrolytes (PGEs) of cobalt redox system are prepared for dye sensitized solar cell (DSSC) applications. Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) is used as a gelator of an acetonitrile (ACN) liquid electrolyte containing tris(2,2'-bipyridine)cobalt(II/III) redox couple. Titanium dioxide (TiO2) and titanium carbide (TiC) nanoparticles are utilized as nanofillers (NFs) of this PGE, and the effects of the two NFs on the conductivity of the PGEs, charge-transfer resistances at the electrode/PGE interface, and the performance of the gel-state DSSCs are studied and compared. The results show that the presence of TiC NFs significantly increases the conductivity of the PGE and decreases the charge-transfer resistance at the Pt counter-electrode (CE)/PGE interface. Therefore, the gel-state DSSC utilizing TiC NFs can achieve a conversion efficiency (6.29%) comparable to its liquid counterpart (6.30%), and, furthermore, the cell efficiency can retain 94% of its initial value after a 1000 h stability test at 50 °C. On the contrary, introduction of TiO2 NFs in the PGE causes a decrease of cell performances. It shows that the presence of TiO2 NFs increases the charge-transfer resistance at the Pt CE/PGE interface, induces the charge recombination at the photoanode/PGE interface, and, furthermore, causes a dye desorption in a long-term-stability test. These results are different from those reported for the iodide redox system and are ascribed to a specific attractive interaction between TiO2 and cobalt redox ions.

  19. Thiourea incorporated poly(ethylene oxide) as transparent gel polymer electrolyte for dye sensitized solar cell applications

    Science.gov (United States)

    Pavithra, Nagaraj; Velayutham, David; Sorrentino, Andrea; Anandan, Sambandam

    2017-06-01

    A new series of transparent gel polymer electrolytes are prepared by adding various weight percent of thiourea coupled with poly(ethylene oxide) for the application of dye-sensitized solar cells. Coupling of thiourea in the presence of iodine undergoes dimerization reaction to produce formamidine disulfide. Fourier Transform Infrared spectroscopy shows that the interactions of thiourea and formamidine disulfide with electronegative ether linkage of poly(ethylene oxide) results in conformational changes of gel polymer electrolytes. Electrochemical impedance spectroscopy and linear sweep voltammetry experiments reveal an increment in ionic conductivity and tri-iodide diffusion coefficient, for thiourea modified gel polymer electrolytes. Finally, the prepared electrolytes are used as a redox mediator in dye-sensitized solar cells and the photovoltaic properties were studied. Apart from transparency, the gel polymer electrolytes with thiorurea show higher photovoltaic properties compared to bare gel polymer electrolyte and a maximum photocurrent efficiency of 7.17% is achieved for gel polymer electrolyte containing 1 wt% of thiourea with a short circuit current of 11.79 mA cm-2 and open circuit voltage of 834 mV. Finally, under rear illumination, almost 90% efficiency is retained upon compared to front illumination.

  20. Lithium ion conductivity of gel polymer electrolytes containing insoluble lithium tetrakis(pentafluorobenzenethiolato) borate

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Takahiro; Ohta, Takayuki; Fujinami, Tatsuo [Department of Materials Science and Chemical Engineering, Faculty of Engineering, Shizuoka University, 3-5-1, Johoku, Hamamatsu 432-8561 (Japan)

    2006-06-01

    Lithium ion conducting gel polymer electrolytes composed of insoluble lithium tetrakis(pentafluorobenzenethiolato) borate (LiTPSB), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and ethylene carbonate-propylene carbonate mixed solvent (EC-PC) were prepared and their ionic conductivities and electrochemical stabilities were investigated. Ionic conductivity was largely dependent on the contents of EC-PC and LiTPSB. Gel polymer electrolyte containing optimized content of 50 (LiTPSB)-50 (PVDF-HFP/EC-PC (13:87wt.%)) exhibited ionic conductivity of 4x10{sup -4}Scm{sup -1} at 30{sup o}C, lithium ion transference number of 0.33 and anodic oxidation potential of 4.2V. (author)

  1. Lithium ion conductivity of gel polymer electrolytes containing insoluble lithium tetrakis(pentafluorobenzenethiolato) borate

    Science.gov (United States)

    Aoki, Takahiro; Ohta, Takayuki; Fujinami, Tatsuo

    Lithium ion conducting gel polymer electrolytes composed of insoluble lithium tetrakis(pentafluorobenzenethiolato) borate (LiTPSB), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and ethylene carbonate-propylene carbonate mixed solvent (EC-PC) were prepared and their ionic conductivities and electrochemical stabilities were investigated. Ionic conductivity was largely dependent on the contents of EC-PC and LiTPSB. Gel polymer electrolyte containing optimized content of 50 (LiTPSB)-50 (PVDF-HFP/EC-PC (13:87 wt.%)) exhibited ionic conductivity of 4 × 10 -4 S cm -1 at 30 °C, lithium ion transference number of 0.33 and anodic oxidation potential of 4.2 V.

  2. Poly(vinylidene fluoride-hexafluoropropylene) polymer electrolyte for paper-based and flexible battery applications

    Science.gov (United States)

    Aliahmad, Nojan; Shrestha, Sudhir; Varahramyan, Kody; Agarwal, Mangilal

    2016-06-01

    Paper-based batteries represent a new frontier in battery technology. However, low-flexibility and poor ionic conductivity of solid electrolytes have been major impediments in achieving practical mechanically flexible batteries. This work discuss new highly ionic conductive polymer gel electrolytes for paper-based battery applications. In this paper, we present a poly(vinylidene fluoride-hexafluoropropylene) (PVDH-HFP) porous membrane electrolyte enhanced with lithium bis(trifluoromethane sulphone)imide (LiTFSI) and lithium aluminum titanium phosphate (LATP), with an ionic conductivity of 2.1 × 10-3 S cm-1. Combining ceramic (LATP) with the gel structure of PVDF-HFP and LiTFSI ionic liquid harnesses benefits of ceramic and gel electrolytes in providing flexible electrolytes with a high ionic conductivity. In a flexibility test experiment, bending the polymer electrolyte at 90° for 20 times resulted in 14% decrease in ionic conductivity. Efforts to further improving the flexibility of the presented electrolyte are ongoing. Using this electrolyte, full-cell batteries with lithium titanium oxide (LTO) and lithium cobalt oxide (LCO) electrodes and (i) standard metallic current collectors and (ii) paper-based current collectors were fabricated and tested. The achieved specific capacities were (i) 123 mAh g-1 for standard metallic current collectors and (ii) 99.5 mAh g-1 for paper-based current collectors. Thus, the presented electrolyte has potential to become a viable candidate in paper-based and flexible battery applications. Fabrication methods, experimental procedures, and test results for the polymer gel electrolyte and batteries are presented and discussed.

  3. Poly(vinylidene fluoride-hexafluoropropylene polymer electrolyte for paper-based and flexible battery applications

    Directory of Open Access Journals (Sweden)

    Nojan Aliahmad

    2016-06-01

    Full Text Available Paper-based batteries represent a new frontier in battery technology. However, low-flexibility and poor ionic conductivity of solid electrolytes have been major impediments in achieving practical mechanically flexible batteries. This work discuss new highly ionic conductive polymer gel electrolytes for paper-based battery applications. In this paper, we present a poly(vinylidene fluoride-hexafluoropropylene (PVDH-HFP porous membrane electrolyte enhanced with lithium bis(trifluoromethane sulphoneimide (LiTFSI and lithium aluminum titanium phosphate (LATP, with an ionic conductivity of 2.1 × 10−3 S cm−1. Combining ceramic (LATP with the gel structure of PVDF-HFP and LiTFSI ionic liquid harnesses benefits of ceramic and gel electrolytes in providing flexible electrolytes with a high ionic conductivity. In a flexibility test experiment, bending the polymer electrolyte at 90° for 20 times resulted in 14% decrease in ionic conductivity. Efforts to further improving the flexibility of the presented electrolyte are ongoing. Using this electrolyte, full-cell batteries with lithium titanium oxide (LTO and lithium cobalt oxide (LCO electrodes and (i standard metallic current collectors and (ii paper-based current collectors were fabricated and tested. The achieved specific capacities were (i 123 mAh g−1 for standard metallic current collectors and (ii 99.5 mAh g−1 for paper-based current collectors. Thus, the presented electrolyte has potential to become a viable candidate in paper-based and flexible battery applications. Fabrication methods, experimental procedures, and test results for the polymer gel electrolyte and batteries are presented and discussed.

  4. Chaotic behavior of ion exchange phenomena in polymer gel electrolytes through irradiated polymeric membrane

    Energy Technology Data Exchange (ETDEWEB)

    Rawat, Sangeeta; Saha, Barnamala; Prasad, Awadhesh [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Chandra, Amita, E-mail: achandra@physics.du.ac.in [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2012-05-14

    A desktop experiment has been done to show the nonlinearity in the I–V characteristics of an ion conducting electrochemical micro-system. Its chaotic dynamics is being reported for the first time which has been captured by an electronic circuit. Polyvinylidene fluoride-co-hexafluoropropene (PVdF-HFP) gel electrolyte comprising of a combination of plasticizers (ethylene carbonate and propylene carbonate) and salts have been prepared to study the exchange of ions through porous polyethylene terephthalate (PET) membranes. The nonlinearity of this system is due to the ion exchange of the polymer gel electrolytes (PGEs) through a porous membrane. The different regimes of spiking and non-spiking chaotic motions are being presented. The possible applications are highlighted. -- Highlights: ► For the first time, the nonlinear dynamics of an electrochemical micro-system has been reported. ► The nonlinearity generates due to the ion exchange of polymer gel electrolytes through irradiated polymeric membrane. ► The nonlinearity can be tailored by changing the pore size of irradiated membrane. ► Sprott's circuit has been modified to capture the phenomena of ion transport through membrane. ► Attractor formation and Lyapunov exponent confirms the chaotic behavior of presently investigated system.

  5. Correlation between ionic conductivity and fluidity of polymer gel electrolytes containing NH4CF3SO3

    Indian Academy of Sciences (India)

    Harinder Pal Singh; Rajiv Kumar; S S Sekhon

    2005-08-01

    Nonaqueous polymer gel electrolytes containing ammonium triflate (NH4CF3SO3) and dimethylacetamide (DMA) with polymethylmethacrylate (PMMA) as the gelling polymer have been synthesized which show high value of conductivity (∼ 10-2 S/cm) at 25°C. The conductivity of polymer gel electrolytes containing different concentrations of NH4CF3SO3 shows a small decrease with the addition of PMMA and this has been correlated with the variation of fluidity of these gel electrolytes. The small decrease in conductivity with PMMA addition shows that polymer plays the role of stiffener and this is supported by FTIR results which also indicates the absence of any active interaction between polymer and NH4CF3SO3 in these gel electrolytes.

  6. Handheld Microneedle-Based Electrolyte Sensing Platform.

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Philip R. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Rivas, Rhiana [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Johnson, David [Aquila Technologies Group, Inc., Albuquerque, NM (United States); Edwards, Thayne L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Koskelo, Markku [Aquila Technologies Group, Inc., Albuquerque, NM (United States); Shawa, Luay [Aquila Technologies Group, Inc., Albuquerque, NM (United States); Brener, Igal [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Chavez, Victor H. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Polsky, Ronen [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-11-01

    Sandia National Laboratories will provide technical assistance, within time and budget, to Requester on testing and analyzing a microneedle-based electrolyte sensing platform. Hollow microneedles will be fabricated at Sandia and integrated with a fluidic chip using plastic laminate prototyping technology available at Sandia. In connection with commercial ion selective electrodes the sensing platform will be tested for detection of electrolytes (sodium and/or potassium) within physiological relevant concent ration ranges.

  7. Influence of the Ionic Liquid Type on the Gel Polymer Electrolytes Properties

    Directory of Open Access Journals (Sweden)

    Juan P. Tafur

    2015-11-01

    Full Text Available Gel Polymer Electrolytes (GPEs composed by ZnTf2 salt, poly(vinylidene fluoride-co-hexafluoropropylene (PVdF-HFP, and different ionic liquids are synthesized using n-methyl-2-pyrrolidone (NMP as solvent. Three different imidazolium-based ionic liquids containing diverse cations and anions have been explored. Structural and electrical properties of the GPEs varying the ZnTf2 concentration are analyzed by ATR-FTIR, DSC, TG, and cyclic voltammetry. Free salt IL-GPEs present distinct behavior because they are influenced by the different IL cations and anions composition. However, inclusion of ZnTf2 salt inside the polymers provide GPEs with very similar characteristics, pointing out that ionic transport properties are principally caused by Zn2+ and triflate movement. Whatever the IL used, the presence of NMP solvent inside the polymer’s matrix turns out to be a key factor for improving the Zn2+ transport inside the GPE due to the interaction between Zn2+ cations and carbonyl groups of the NMP. High values of ionic conductivity, low activation energy values, and good voltammetric reversibility obtained regardless of the ionic liquid used enable these GPEs to be applied in Zn batteries. Capacities of 110–120 mAh·g−1 have been obtained for Zn/IL-GPE/MnO2 batteries discharged at −1 mA·cm−2.

  8. Influence of the Ionic Liquid Type on the Gel Polymer Electrolytes Properties.

    Science.gov (United States)

    Tafur, Juan P; Santos, Florencio; Romero, Antonio J Fernández

    2015-11-19

    Gel Polymer Electrolytes (GPEs) composed by ZnTf₂ salt, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP), and different ionic liquids are synthesized using n-methyl-2-pyrrolidone (NMP) as solvent. Three different imidazolium-based ionic liquids containing diverse cations and anions have been explored. Structural and electrical properties of the GPEs varying the ZnTf₂ concentration are analyzed by ATR-FTIR, DSC, TG, and cyclic voltammetry. Free salt IL-GPEs present distinct behavior because they are influenced by the different IL cations and anions composition. However, inclusion of ZnTf₂ salt inside the polymers provide GPEs with very similar characteristics, pointing out that ionic transport properties are principally caused by Zn(2+) and triflate movement. Whatever the IL used, the presence of NMP solvent inside the polymer's matrix turns out to be a key factor for improving the Zn(2+) transport inside the GPE due to the interaction between Zn(2+) cations and carbonyl groups of the NMP. High values of ionic conductivity, low activation energy values, and good voltammetric reversibility obtained regardless of the ionic liquid used enable these GPEs to be applied in Zn batteries. Capacities of 110-120 mAh·g(-1) have been obtained for Zn/IL-GPE/MnO₂ batteries discharged at -1 mA·cm(-2).

  9. Fast Switching Electrochromic Devices Containing Optimized BEMA/PEGMA Gel Polymer Electrolytes

    Directory of Open Access Journals (Sweden)

    N. Garino

    2013-01-01

    Full Text Available An optimized thermoset gel polymer electrolyte based on Bisphenol A ethoxylate dimethacrylate and Poly(ethylene glycol methyl ether methacrylate (BEMA/PEGMA was prepared by facile photo-induced free radical polymerisation technique and tested for the first time in electrochromic devices (ECD combining WO3 sputtered on ITO as cathodes and V2O5 electrodeposited on ITO as anodes. The behaviour of the prepared ECD was investigated electrochemically and electro-optically. The ECD transmission spectrum was monitored in the visible and near-infrared region by varying applied potential. A switching time of ca. 2 s for Li+ insertion (coloring and of ca. 1 s for Li+ de-insertion (bleaching were found. UV-VIS spectroelectrochemical measurements evidenced a considerable contrast between bleached and colored state along with a good stability over repeated cycles. The reported electrochromic devices showed a considerable enhancement of switching time with respect to the previously reported polymeric ECD indicating that they are good candidates for the implementation of intelligent windows and smart displays.

  10. A porous poly(vinylidene fluoride) gel electrolyte for lithium ion batteries prepared by using salicylic acid as a foaming agent

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H.P. [Department of Material Science, Fudan University, Shanghai 200433 (China); Department of Chemistry and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Zhang, P.; Li, G.C.; Wu, Y.P. [Department of Chemistry and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Sun, D.L. [Department of Material Science, Fudan University, Shanghai 200433 (China)

    2009-04-01

    A porous gel polymer electrolyte based on poly(vinylidene fluoride) (PVDF) was for the first time prepared via a foaming technology using salicylic acid as a foaming agent. The pores are evenly distributed with an average diameter of about 400 nm. The results from TG/DTA, XRD and FT-IR show that there are no vesicant residues after the PVDF film was heat-treated at 200 C to get the porous structure. When the film is gelled with liquid electrolyte, the ion conductivity can be up to 4.8 x 10{sup -3} S cm{sup -1} at room temperature and the activation energy for ionic transfer is 10.2 kJ mol{sup -1}. LiCoO{sub 2} cathode also presents good cycling performance. These primary results show great promise for this simple method to prepare porous gel polymer electrolytes for practical application in lithium ion batteries. (author)

  11. Multifunctional Free-Standing Gel Polymer Electrolyte with Carbon Nanofiber Interlayers for High-Performance Lithium-Sulfur Batteries.

    Science.gov (United States)

    Choi, Sinho; Song, Jianjun; Wang, Chengyin; Park, Soojin; Wang, Guoxiu

    2017-07-04

    Free-standing trimethylolpropane ethoxylate triacrylate gel polymer electrolyte is synthesized by a chemical cross-linking process and used as an electrolyte and separator membrane in lithium-sulfur batteries. The cross linked gel polymer electrolyte also exhibited a stable geometric size retention of 95 % at the high temperature of 130 °C. The as-prepared gel polymer electrolyte membrane with carbon nanofibers interlayer can effectively prevent polysulfide dissolution and shuttle effect, leading to significantly enhanced electrochemical properties, including high capacity and cycling stability, with an enhanced specific capacity of 790 mA h g(-1) after 100 cycles. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Enhancing the performance of dye-sensitized solar cells by incorporating nanomica in gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Yi-Hsuan; Lin, Chia-Yu.; Chen, Jian-Ging; Wang, Chun-Chieh; Huang, Kuan-Chieh [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Liu, Ken-Yen [Department of Materials and Science Engineering, National Taiwan University, Taipei 10617 (China); Lin, King-Fu [Department of Materials and Science Engineering, National Taiwan University, Taipei 10617 (China); Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China); Lin, Jiang-Jen [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China); Ho, Kuo-Chuan [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China)

    2010-04-15

    Gel-type dye-sensitized solar cells (DSSCs) were fabricated with 5.0 wt% polyvinyidene fluoride-co-hexafluoro propylene (PVDF-HFP) in methoxy propionitrile (MPN) as gel polymer electrolyte (GPE), 1-butyl-3-methylimidazolium iodide (BMII)/iodine (I{sub 2}) as redox couple, 4-tertiary butyl pyridine (TBP) and guanidine thiocyanate as additives. The incorporation of alkyl-modified nanomica (AMNM) in the PVDF-HFP gel electrolytes caused the reduction of crystallization of PVDF-HFP, which was confirmed by X-ray diffraction (XRD) analysis. The short-circuit current density (J{sub SC}) of the cell increased due to the decrease of diffusion resistance, as judged by the electrochemical impedance spectra (EIS) analysis, while the open-circuit voltage (V{sub OC}) remained almost the same. As the loading of AMNM in the PVDF-HFP gel electrolyte was increased to 3.0 wt%, the J{sub SC} and power conversion efficiency ({eta}) of the cells increased from 8.3 to 13.6 mA/cm{sup 2} and 3.5% to 5.7%, respectively. However, the J{sub SC} decreased as the loading of AMNM exceeded 3.0 wt%. At higher AMNM loadings, nanomica acted as a barrier interface between the electrolyte and the dye molecules to hinder electron transfer, and thus reducing the cell's photocurrent density. Furthermore, the DSSCs fabricated by dispersing polymethyl methacrylate (PMMA) microspheres in the TiO{sub 2} electrode with the GPE containing 3.0 wt% AMNM improved the {eta} to 6.70%. The TiO{sub 2} films would exhibit larger porosity by blending with PMMA, leading the penetration of GPEs into the porous TiO{sub 2} easier, thus improving the contact between the dye-adsorbed TiO{sub 2} surfaces and the GPEs, as characterized by EIS. Moreover, the {eta} of gel-type DSSCs with a 25 {mu}m thickness of surlyn reached 7.96% as compared with 6.70% for the DSSCs with a 60 {mu}m surlyn. (author)

  13. Mediating gel formation from structurally controlled poly(electrolytes) through multiple "head-to-body" electrostatic interactions.

    Science.gov (United States)

    Srour, Hassan; Ratel, Olivier; Leocmach, Mathieu; Adams, Emma A; Denis-Quanquin, Sandrine; Appukuttan, Vinukrishnan; Taberlet, Nicolas; Manneville, Sébastien; Majesté, Jean-Charles; Carrot, Christian; Andraud, Chantal; Monnereau, Cyrille

    2015-01-01

    Tuning the chain-end functionality of a short-chain cationic homopolymer, owing to the nature of the initiator used in the atom transfer radical polymerization (ATRP) polymerization step, can be used to mediate the formation of a gel of this poly(electrolyte) in water. While a neutral end group gives a solution of low viscosity, a highly homogeneous gel is obtained with a phosphonate anionic moiety, as characterized by rheometry and diffusion nuclear magnetic resonance (NMR). This novel type of supramolecular control over poly(electrolytic) gel formation could find potential use in a variety of applications in the field of electro-active materials.

  14. RESEARCH PROGRESS OF GEL POLYMER ELECTROLYTES FOR LITHIUM ION BATTERIES%锂离子电池凝胶聚合物电解质研究进展

    Institute of Scientific and Technical Information of China (English)

    张鹏; 李琳琳; 何丹农; 吴宇平; 清水真

    2011-01-01

    In recent decades,gel polymer electrolytes (GPEs) have received renewed attention in several areas such as lithium-ion batteries,solar cells and super capacitors due to their promising application. GPEs,swollen in a liquid electrolyte becoming plasticized or a gelled polymer electrolyte, have attracted particular attention because they may provide lighter and safer batteries with longer shelf life,leak proof construction andeasy fabrication into desired shape and size. However, GPEs still show poor mechanical strength due to the need for impregnation with the liquid electrolytes. This significant drawback of GPEs binders their practical application. To overcome these problems, in this review, the up-to-date technologies such as composite gel polymer electrolyte (CGPEs) and porous polymer electrolytes (PPEs) based on the gel concept have been summarized. In the CGPEs, the role of a filler in the membrane is to provide surface groups as physical crosslinking centers for the polymer segments, and thus reduce the polymer reorganization tendency which establishes additional conducting pathways on the filler surface. As a result, the nanosized particles not only lead to better ionic conductivity but also interact with the polymer hosts to enhance the mechanical strength. In PGPEs,due to the existence of the porous structure,the lithium ions can migrate not only in gel electrolyte butalso in liquid electrolyte stored in the pores, leading to higher ionic conductivity. In addition, the main characteristics of these gel polymer electrolytes were mentioned. Finally, the future directions are also pointed out.%使用聚合物电解质可以避免传统液态锂离子电池的漏液问题,提高电池的安全性能和能量密度,并可实现电池的薄型化、轻便化和形状可变等优点.目前,聚合物电解质的研究集中在凝胶型的复合和多孔聚合物电解质两大类.本文对各类凝胶聚合物电解质的特点、功能及研究情况逐一进

  15. DNA-poly(vinyl alcohol) gel matrices: release properties are strongly dependent on electrolytes and cationic surfactants.

    Science.gov (United States)

    Valente, Artur J M; Cruz, Sandra M A; Murtinho, Dina M B; Miguel, M Graça; Muniz, Edvani C

    2013-01-01

    The release of DNA from cryogel PVA-DNA gel matrices to different electrolyte aqueous solutions was investigated. The rate of release and the distribution coefficient of DNA have been quantified by using a first order kinetic law equation, developed in the frame of a partition-based model. The release of DNA from gels to 1:1 sodium and nitrate salts shows that the transport properties are dependent on the ability of anions/cations to solubilise the DNA in the aqueous phase which, with the exception of bromide, can be related to the Hofmeister series; in the presence of multivalent electrolytes, or increasing the ionic strength, the condensation of DNA inside the gel, followed by a phase separation as seen by scanning electron microscopy, induces the retention of DNA inside the polymer matrix. The DNA condensation and/or phase separation, which contribute to a decrease in the water volume fraction inside the gel, determined by swelling degree experiments, also lead to a decrease in the rate constant of DNA release; such decrease can be justified by the difficulty of the molecular aggregate to move through out the polymeric structure. The DNA release is also dependent on the pH of the bulk solution. The effect of uni- and di-valent cationic surfactants on the release properties of DNA was also evaluated. Our findings suggest that the kinetics of DNA release depends on a complex balance between different structural properties of the surfactants, namely charge, bulkiness of the headgroup and alkyl chain length.

  16. Improved Electrodes and Electrolytes for Dye-Based Solar Cells

    Energy Technology Data Exchange (ETDEWEB)

    Harry R. Allcock; Thomas E. Mallouk; Mark W. Horn

    2011-10-26

    The most important factor in limiting the stability of dye-sensitized solar cells is the use of volatile liquid solvents in the electrolytes, which causes leakage during extended operation especially at elevated temperatures. This, together with the necessary complex sealing of the cells, seriously hampers the industrial-scale manufacturing and commercialization feasibilities of DSSCs. The objective of this program was to bring about a significant improvement in the performance and longevity of dye-based solar cells leading to commercialization. This had been studied in two ways first through development of low volatility solid, gel or liquid electrolytes, second through design and fabrication of TiO2 sculptured thin film electrodes.

  17. Modified sol-gel method used for obtaining SOFC electrolyte materials

    Energy Technology Data Exchange (ETDEWEB)

    Suciu, C.; Maeland, D.; Hoffmann, A.C. [Bergen Univ., Bergen (Norway). Dept. of Physics and Technology; Dorolti, E.; Tetean, R. [Babes-Bolyai Univ., Cluj-Napoca (Romania). Faculty of Physics

    2009-07-01

    Solid oxide fuel cells (SOFCs) offer significant advantages over conventional energy generation technologies. However, increases in current density and reliability must be achieved in order to ensure the commercialization of SOFCs. This study used a modified sol-gel method with sucrose and pectin as organic precursors to obtain a 6 and 10 mol per cent scandia stabilized zirconia (SSZ) electrolyte material. The SSZ electrolyte offered higher conductivity, while the organic precursors helped to reduce the high cost of the SSZ. The composite powders were pressed as pellets and sintered at 1400 degrees C for 16 hours at a temperature of 200 degrees C. Transmission electron microscopy (TEM), X-ray diffraction, BET and electronic impedance spectroscopy (EIP) were used to analyze the morphology, particle and crystallite size, crystal structure and specific surface area of the pellets. The electrical properties of the sintered pellets were also analyzed.

  18. Ionic Liquid-Doped Gel Polymer Electrolyte for Flexible Lithium-Ion Polymer Batteries

    Science.gov (United States)

    Zhang, Ruisi; Chen, Yuanfen; Montazami, Reza

    2015-01-01

    Application of gel polymer electrolytes (GPE) in lithium-ion polymer batteries can address many shortcomings associated with liquid electrolyte lithium-ion batteries. Due to their physical structure, GPEs exhibit lower ion conductivity compared to their liquid counterparts. In this work, we have investigated and report improved ion conductivity in GPEs doped with ionic liquid. Samples containing ionic liquid at a variety of volume percentages (vol %) were characterized for their electrochemical and ionic properties. It is concluded that excess ionic liquid can damage internal structure of the batteries and result in unwanted electrochemical reactions; however, samples containing 40–50 vol % ionic liquid exhibit superior ionic properties and lower internal resistance compared to those containing less or more ionic liquids.

  19. Synthesis and Characterization of a Gel-Type Electrolyte with Ionic Liquid Added for Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    Le-Yan Shi

    2013-01-01

    Full Text Available This study intends to develop the electrolyte needed in dye-sensitized solar cells (DSSCs. Moreover, three different ionic liquids in different molalities are added to the gel-type electrolyte. Experimental results show that the DSSC composed of the gel-type electrolyte with no ionic liquid added can acquire 4.13% photoelectric conversion efficiency. However, the DSSC composed of the gel-type electrolyte with 0.4 M of 1-butyl-3-methylimidazolium chloride added has an open-circuit voltage of 810 mV, a short-circuit current density of 9.56 mA/cm2, and photoelectric conversion efficiency reaching 4.89%. Comparing this DSSC with the DSSC with no ionic liquid added, the photoelectric conversion efficiency can be enhanced by 18.4%. As to durability, the DSSC composed of the gel-type electrolyte with ionic liquid added still has a photoelectric conversion efficiency of 3.28% on the 7th day after it is stored in an enclosed space and maintains 0.72% efficiency on the 14th day. When the proposed DSSC is compared with the DSSC prepared by using a liquid-type electrolyte, the durability of its photoelectric conversion efficiency can be increased by 7 times.

  20. Dye-sensitized solar cells assembled with composite gel polymer electrolytes containing nanosized Al2O3 particles.

    Science.gov (United States)

    Jeon, Nawon; Kim, Dong-Won

    2013-12-01

    Polymeric ionic liquid, poly(1-methyl 3-(2-acryloyloxy propyl) imidazolium iodide) (PMAPII) containing iodide ions is synthesized and used as a matrix polymer for preparing the composite polymer electrolytes. The composite gel polymer electrolytes are prepared by utilizing PMAPII, organic solvent containing redox couple and aluminum oxide nanoparticle for application in dye-sensitized solar cells (DSSCs). PMAPII is highly compatible with organic solvents and thus there is no phase separation between the PMAPII and organic solvents. This makes it be possible to directly solidify the liquid electrolyte in the cell and maintain good interfacial contacts between the electrolyte and electrodes. The addition of 10 wt.% Al2O3 nanoparticle to gel polymer electrolyte provides the most desirable environment for ionic transport, resulting in the improvement of the photovoltaic performance of DSSC. The quasi-solid-state DSSC assembled with optimized composite gel polymer electrolyte containing 10 wt.% Al2O3 nanoparticle exhibits a relatively high conversion efficiency of 6.51% under AM 1.5 illumination at 100 mA cm(-2) and better stability than DSSC with liquid electrolyte.

  1. Chemical stability of γ-butyrolactone-based electrolytes for aluminum electrolytic capacitors

    Science.gov (United States)

    Ue, Makoto; Takeda, Masayuki; Suzuki, Yoko; Mori, Shoichiro

    γ-Butyrolactone-based electrolytes have been used as the operating electrolytes for aluminum electrolytic capacitors. The chemical stability of these electrolytes at elevated temperatures has been examined by monitoring the decrease in their electrolytic conductivities. The deteriorated electrolytes were analyzed by gas and liquid chromatography and the conductivity decrease was directly correlated with the loss of acid components. In quaternary ammonium hydrogen maleate/γ-butyrolactone electrolytes, the maleate anion decomposed by decarboxylation resulting in a complex polymer containing polyester and polyacrylate structures. Quaternary ammonium benzoate/γ-butyrolactoneelectrolytes decomposed by SN2 reactions giving alkyi benzoates and trialkylamines. The deterioration of the carboxylate salt/γ-butyrolactone electrolytes was accelerated by electrolysis.

  2. Gel electrolytes containing several kinds of particles used in quasi-solid-state dye-sensitized solar cells

    Institute of Scientific and Technical Information of China (English)

    GENG Yi; SUN Xiaodan; CAI Qiang; SHI Yantao; LI Hengde

    2006-01-01

    Composite gel electrolytes containing several kinds of particles used as the quasi-solid-state electrolytes in dye-sensitized solar cells (DSSCs) were reported. Mesoporous particles (MCM-41) with unique structures composed of ordered nanochannels were served as a new kind of gelator for quasi-solid-state electrolytes. MCM-41, hydrophobic fumed silica Aerosil R972 and TiO2 nanopatricles P25 were dispersed into gel electrolytes respectively. The solar energy-to-electricity conversion efficiency of these cells is 4.65%, 6.85% and 5.05% respectively under 30 mW·cm-2 illumination. The preparation methods and the particles sizes exert an influence on the performance of corresponding solar cells. Owing to unique pore structures and high specific BET surface area, mesoporous silica MCM-41 was expected to have the potential to afford conducting nanochannels for redox couple diffusion.

  3. 溶剂为碳酸甘油酯的电解液及凝胶电解质的电化学行为%Electrochemical Behavior of Liquid Electrolyte and Gel Electrolyte Made of Glycerol Carbonate as Solvent

    Institute of Scientific and Technical Information of China (English)

    孙冬兰; 李汝娟; 程绍玲; 肖大刚; 董丹霞

    2015-01-01

    先以甘油和碳酸二甲酯为原料合成碳酸甘油酯(GC),再以 GC 为溶剂制备浓度为0.75 mol/L 的高氯酸锂电解质溶液,测得该电解液的电导率为3.34 mS/cm;以该电解液为增塑剂,聚丙烯腈-甲基丙烯酸甲酯(P (AN-MMA))为高分子骨架制备凝胶电解质,当V (增塑剂)∶V (聚合物)=0.75时,凝胶电解质室温下的电导率为0.94 mS/cm.将其用于结构为玻璃/FTO/WO 3/电解质/CeO 2-TiO 2/FTO/玻璃的电致变色器件,该器件在550 nm 处的变色范围为20%,变色效率为6.89 cm2/C.%Glycerol carbonate was synthesized by the transesterification of glycerol with dimethyl carbonate in the presence of calcium oxide as catalyst.The liquid electrolyte was composed of lithium perchlorate (LiClO 4 )as solute and glycerol carbonate as solvent.The ionic conductivity of the electrolyte with 0.75 mol/L LiClO 4 in GC was 3.34 mS/cm.As a plasticizer,the electrolyte was used to prepare poly (acrylonitrile-methyl methacrylate)(P (AN-MMA))based gel electrolyte.The gel electrolyte was obtained by putting the P(AN-MMA)membrane in the liquid electrolyte.The gelled membrane sucked with 75% of the liquid electrolyte vs the dried membrane presented an ionic conductivity of 0.94 mS/cm at room temperature. When the gel electrolyte applied to the electrochromic devices (ECD)with the configuration glass/FTO/WO 3/electrolyte/CeO 2-TiO 2/FTO/glass,the transmittance change of the ECD reached 20% at 550 nm and the coloration efficiency of the ECD was 6.89 cm2/C.

  4. Substrate integrated Lead-Carbon hybrid ultracapacitor with flooded, absorbent glass mat and silica-gel electrolyte configurations

    OpenAIRE

    Banerjee, A.; Ravikumar, MK; Jalajakshi, A; Kumar, Suresh P; Gaffoor, SA; Shukla, AK

    2012-01-01

    Lead-Carbon hybrid ultracapacitors (Pb-C HUCs) with flooded, absorbent-glass-mat (AGM) and silica-gel sulphuric acid electrolyte configurations are developed and performance tested. Pb-C HUCs comprise substrate-integrated PbO2 (SI-PbO2) as positive electrodes and high surface-area carbon with graphite-sheet substrate as negative electrodes. The electrode and silica-gel electrolyte materials are characterized by XRD, XPS, SEM, TEM, Rheometry, BET surface area, and FTIR spectroscopy in conjunct...

  5. New polysaccharide-based polymer electrolytes; Nouveaux electrolytes polymeres a base de polysaccharides

    Energy Technology Data Exchange (ETDEWEB)

    Velasquez-Morales, P.; Le Nest, J.F.; Gandini, A. [Ecole Francaise de Papeterie et des Industries Graphique, 38 - Saint Martin d`Heres (France)

    1996-12-31

    Polysaccharides like cellulose and chitosan are known for their filmic properties. This paper concerns the synthesis and the study of chitosan-based polymer electrolytes. A preliminary work concerns the study of glucosamine reactivity. The poly-condensation of chitosan ethers (obtained by reaction with ethylene oxide or propylene oxide) with bifunctional and monofunctional oligo-ethers leads to the formation of thin lattices (10 {mu}m) having excellent mechanical properties. The presence of grafted polyether chains along the polysaccharide skeleton allows to modify the vitreous transition temperature and the molecular disorder of the system. Two type of polymer electrolytes have been synthesized: electrolytes carrying a dissolved alkaline metal salt and ionomers. The analysis of their thermal, dynamical mechanical, nuclear magnetic relaxation, electrical, and electrochemical properties shows that this new class of polymer electrolytes has the same performances as ethylene poly-oxide based amorphous lattices plus the advantage of having good filmic properties. Abstract only. (J.S.)

  6. Quasi-solid-state dye-sensitized solar cells from hydrophobic poly(hydroxyethyl methacrylate/glycerin)/polyaniline gel electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qinghua [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); Tang, Qunwei, E-mail: tangqunwei@hotmail.com [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Chen, Haiyan [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Xu, Haitao; Qin, Yuancheng [National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology, Nanchang Hangkong University, Nanchang 330063 (China); He, Benlin, E-mail: blhe@ouc.edu.cn [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China); Liu, Zhichao; Jin, Suyue; Chu, Lei [Institute of Materials Science and Engineering, Ocean University of China, Shandong Province, Qingdao 266100 (China)

    2014-04-01

    Hydrophobic poly(hydroxyethyl methacrylate/glycerin) [poly(HEMA/GR)] gel with a three-dimensional (3D) framework was successfully fabricated and employed to integrate with polyaniline (PANi). The resultant poly(HEMA/GR)/PANi gel electrolyte exhibited interconnective porous structure for holding I{sup −}/I{sub 3}{sup −}, giving a similar conduction mechanism and ionic conductivity to that of liquid system but a much enhanced retention of I{sup −}/I{sub 3}{sup −} redox couple. Fourier transform infrared spectroscopy, X-ray diffraction patterns, cyclic voltammograms as well as electrochemical impedance spectroscopy were employed to evaluate the molecular structure, crystallinity, and the electrochemical behaviors, showing that the combination of PANi with poly(HEMA/GR) caused a lower charge-transfer resistance and higher electrocatalytic activity for the I{sub 3}{sup −}/I{sup −} redox reaction in the gel electrolyte. An efficiency of 6.63% was recorded from the quasi-solid-state DSSC assembled with the poly(HEMA/GR)/PANi gel electrolyte at 100 mW cm{sup −2}. - Graphical abstract: A poly(HEMA/GR)/PANi gel electrolyte is synthesized through in situ polymerization of PANi in 3D framework of poly(HEMA/GR) hydrophobic hydrogel. The recorded ionic conductivity and electrochemical performances are significantly enhanced by integrating with PANi The resultant overall photo-to-electric conversion efficiency is 6.63%. The high ionic conductivity, along with good electrolyte retention ability, reasonable DSSC performance, low cost, simple and scalable synthesis procedure, and competitive cost, promises the electrolyte to find applications in quasi-solid-state DSSCs. - Highlights: • Poly(HEMA/GR) was employed to combine with PANi in the 3D framework. • The conductivity and electrochemical performances were enhanced. • The conversion efficiency of the quasi-solid-state DSSC was 6.63%.

  7. Mechanisms of ionic conduction related to the structure of the gel electrolytes composed of cross-linked PEO matrix; Kakyo PEO wo matrix kokkaku to suru gel denkaishitsu no kozo to ion ido kiko

    Energy Technology Data Exchange (ETDEWEB)

    Aihara, Y.; Arai, S. [Yuasa Corp., Osaka (Japan); Hayamizu, K. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Price, W.

    1998-04-27

    The ionic conduction mechanism of a non-aqueous polymer gel electrolyte based on the matrix of a chemically cross-linked polyethylene oxide is reported. Subjected to experiment in this report is a polyethylene oxide (PEO)/{gamma}-butyrolactone (GBL) base electrolyte . In this electrolyte, GBL is the solvent and LiBF4 is the solute, and cross-linked polyethylene glycol diacrylate serves as the matrix polymer. Concerning this gel electrolyte, ionic conductivity is determined by the AC impedance method, and diffusion coefficients are determined respectively for the polymer, GBL, Li{sup +}, and BF4{sup -} by measuring nuclear magnetic resonance using the field gradient method. In addition , the outcome of measurement by DSC (differential scanning calorimeter) is mentioned. One of the conclusions arrived at after evaluating the above-said results is described below. It is opined that the diffusion of BF4{sup -} and GBL proceeds at a relatively high rate while Li{sup +} moves on interacting with the matrix polymer and subjected to solvent exchange in the adjacent region. 19 refs., 6 figs., 4 tabs.

  8. Performance of Lithium Polymer Cells with Polyacrylonitrile based Electrolyte

    DEFF Research Database (Denmark)

    Perera, Kumudu; Skaarup, Steen; West, Keld

    2006-01-01

    The performance of lithium polymer cells fabricated with Polyacrylonitrile (PAN) based electrolytes was studied using cycling voltammetry and continuous charge discharge cycling. The electrolytes consisted of PAN, ethylene carbonate (EC), propylene carbonate (PC) and lithium trifluoromethanesulfo......The performance of lithium polymer cells fabricated with Polyacrylonitrile (PAN) based electrolytes was studied using cycling voltammetry and continuous charge discharge cycling. The electrolytes consisted of PAN, ethylene carbonate (EC), propylene carbonate (PC) and lithium...

  9. ZnTe Semiconductor-Polymer Gel Composited Electrolyte for Conversion of Solar Energy

    Directory of Open Access Journals (Sweden)

    Wonchai Promnopas

    2014-01-01

    Full Text Available Nanostructured cubic p-type ZnTe for dye sensitized solar cells (DSSCs was synthesized from 1 : 1 molar ratio of Zn : Te by 600 W and 900 W microwave plasma for 30 min. In this research, their green emissions were detected at the same wavelengths of 563 nm, the energy gap (Eg at 2.24 eV, and three Raman shifts at 205, 410, and 620 cm−1. The nanocomposited electrolyte of quasisolid state ZnO-DSSCs was in correlation with the increase in the JSC, VOC, fill factor (ff, and efficiency (η by increasing the wt% of ZnTe-GPE (gel polymer electrolyte to an optimum value and decreased afterwards. The optimal ZnO-DSSC performance was achieved for 0.20 wt% ZnTe-GPE with the highest photoelectronic energy conversion efficiency at 174.7% with respect to that of the GPE without doping of p-type ZnTe.

  10. DMA and Conductivity Studies in PVA:NH4SCN:DMSO:MWNT Nanocomposite Polymer Dried Gel Electrolytes

    Directory of Open Access Journals (Sweden)

    S. L. Agrawal

    2015-01-01

    Full Text Available This paper deals with findings on dynamic mechanical analysis (DMA and ion-conduction behavior of MWNTs (multiwall carbon nanotubes doped PVA:NH4SCN:DMSO dried gel electrolyte system prepared for four filler concentrations (2, 4, 6 & 8 wt% by solution cast technique. XRD measurements reveal enhancement in amorphous behavior of composite gel electrolyte upon incorporation of filler particles. Better mechanical stability is noticed in the composite system upon dispersal of MWNT along with presence of dynamic Tg during DMA measurements. Enhancement in ionic conductivity has been noticed with an optimum value of 4.5 × 10−3 Scm−1 for 6 wt% MWNTs filled composite electrolyte. Composite system exhibits combination of Arrhenius and Vogel-Tammam-Fulcher (VTF behavior in temperature dependent conductivity study. The a.c. conductivity response seems to follow universal power law.

  11. Open-circuit voltage enhancement on the basis of polymer gel electrolyte for a highly stable dye-sensitized solar cell.

    Science.gov (United States)

    Wu, Congcong; Jia, Lichao; Guo, Siyao; Han, Song; Chi, Bo; Pu, Jian; Jian, Li

    2013-08-28

    Dye-sensitized solar cells (DSSC) have received considerable attention owing to their low preparation cost and easy fabrication process. However, one of the drawbacks that limits the further application of DSSC is their poor stability, arising from the leakage and volatilization of the liquid organic solvent in the electrolyte. Therefore, to improve the long-term stability of DSSC, polymer gel electrolyte was studied to replace the conventional liquid electrolyte in this work. The results show that compared to liquid electrolyte, DSSC with polymer gel electrolyte has a smaller short-circuit current (Jsc), which decreases with the increase of the polymer gelator. Nevertheless, with the employment of the polymer gel electrolyte, there is a significant enhancement of open-circuit voltage (Voc), and it increases with the increase of the polymer gelator content. The highest Voc, up to 0.873 V, can be obtained for DSSC with a 30% polymer gelator content. The impact of the polymer gel electrolyte on the photovoltaic performance of DSSC, especially on Voc, was studied by analyzing the charge-transfer kinetics in the polymer gel electrolyte. Furthermore, the influence of the polymer gel electrolyte on the long-term stability of DSSC was also investigated.

  12. Effects of crown ethers in nanocomposite silica-gel electrolytes on the performance of quasi-solid-state dye-sensitized solar cells

    KAUST Repository

    Huang, Kuan-Chieh

    2010-04-01

    The effects of crown ethers (CEs) on the performance of quasi-solid-state dye-sensitized solar cells (DSSCs) have been investigated. Nanocomposite silica was used to form gel matrices in the electrolytes, which contained lithium iodide (LiI) and iodine (I2) in 3-methoxypropionitrile (MPN) solvent. Three types of CEs, 12-crown-4 (12-C-4), 15-crown-5 (15-C-5), and 18-crown-6 (18-C-6) were used as additives to the gel electrolytes. DSSCs containing CEs showed enhancements in solar-to-electricity conversion efficiencies (η), with reference to the one without them. The crown ether, 15-C-5, with a size of cavity matching with the size of Li+ in the electrolyte rendered for its DSSC the best performance with an η of 3.60%, under 100 mW/cm2 illumination, as compared to 2.44% for the cell without any CE. Enhancements in the photovoltaic parameters of the cells with the CEs were explained based on the binding abilities of the CEs with lithium ions (Li+) in the electrolyte. Linear sweep voltammetry (LSV) measurements and electrochemical impedance spectra were used to substantiate the explanations. © 2009 Elsevier B.V. All rights reserved.

  13. Electrospun PVdF-based fibrous polymer electrolytes for lithium ion polymer batteries

    Energy Technology Data Exchange (ETDEWEB)

    Jeong Rae Kim [Hanyang University, Seoul (France). Applied Chemical Engineering Division; Korea Institute of Science and Technology, Seoul (Korea). Polymer Hybrid Research Center; Sung Won Choi [Yonsei University, Seoul (Korea). Department of Chemistry; Seong Mu Jo; Wha Seop Lee [Korea Institute of Science and Technology, Seoul (Korea). Polymer Hybrid Research Center; Byung Chul Kim [Hanyang University, Seoul (France). Applied Chemical Engineering Division

    2004-11-15

    This paper discusses the preparation of microporous fibrous membranes from PVdF solutions with different polymer contents, using the electrospinning technique. Electrospun PVdF-based fibrous membranes with average fiber diameters (AFD's) of 0.45-1.38 {mu}m have an apparent porosity and a mean pore size (MPS) of 80-89% and 1.1-4.3 {mu}m, respectively. They exhibited a high uptake of the electrolyte solution (320-350%) and a high ionic conductivity of above 1 x 10{sup -3} s/cm at room temperature. Their ionic conductivity increased with the decrease in the AFD of the fibrous membrane due to its high electrolyte uptake. The interaction between the electrolyte molecules and the PVdF with a high crystalline content may have had a minor effect on the lithium ion transfer in the fibrous polymer electrolyte, unlike in a nanoporous gel polymer electrolyte. The fibrous polymer electrolyte that contained a 1 M LiPF{sub 6}-EC/DMC/DEC (1/1/1 by weight) solution showed a high electrochemical stability of above 5.0 V, which increased with the decrease in the AFD. The interfacial resistance (R{sub i}) between the polymer electrolyte and the lithium electrode slightly increased with the storage time, compared with the higher increase in the interfacial resistance of other gel polymer electrolytes. The prototype cell (MCMB/PVdF-based fibrous electrolyte/LiCoO{sub 2}) showed a very stable charge-discharge behavior with a slight capacity loss under constant current and voltage conditions at the C/2-rate of 20 and 60 {sup o}C. (author)

  14. Electrospun PVdF-based fibrous polymer electrolytes for lithium ion polymer batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jeong Rae [Applied Chemical Engineering Division, Hanyang University, 17, Haengdang-dong, Seongdong-Ku, Seoul 133-791 (Korea, Republic of); Polymer Hybrid Research Center, Korea Institute of Science and Technology, 39-1, Hawolgok-dong, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Choi, Sung Won [Department of Chemistry, Yonsei University, 134, Sinchon-dong, Seodaemun-gu, Seoul 120-749 (Korea, Republic of); Polymer Hybrid Research Center, Korea Institute of Science and Technology, 39-1, Hawolgok-dong, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Jo, Seong Mu [Polymer Hybrid Research Center, Korea Institute of Science and Technology, 39-1, Hawolgok-dong, Seongbuk-gu, Seoul 136-791 (Korea, Republic of)]. E-mail: smjo@kist.re.kr; Lee, Wha Seop [Polymer Hybrid Research Center, Korea Institute of Science and Technology, 39-1, Hawolgok-dong, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Kim, Byung Chul [Applied Chemical Engineering Division, Hanyang University, 17, Haengdang-dong, Seongdong-Ku, Seoul 133-791 (Korea, Republic of)

    2004-11-15

    This paper discusses the preparation of microporous fibrous membranes from PVdF solutions with different polymer contents, using the electrospinning technique. Electrospun PVdF-based fibrous membranes with average fiber diameters (AFD's) of 0.45-1.38 {mu}m have an apparent porosity and a mean pore size (MPS) of 80-89% and 1.1-4.3 {mu}m, respectively. They exhibited a high uptake of the electrolyte solution (320-350%) and a high ionic conductivity of above 1 x 10{sup -3} s/cm at room temperature. Their ionic conductivity increased with the decrease in the AFD of the fibrous membrane due to its high electrolyte uptake. The interaction between the electrolyte molecules and the PVdF with a high crystalline content may have had a minor effect on the lithium ion transfer in the fibrous polymer electrolyte, unlike in a nanoporous gel polymer electrolyte. The fibrous polymer electrolyte that contained a 1 M LiPF{sub 6}-EC/DMC/DEC (1/1/1 by weight) solution showed a high electrochemical stability of above 5.0 V, which increased with the decrease in the AFD The interfacial resistance (R{sub i}) between the polymer electrolyte and the lithium electrode slightly increased with the storage time, compared with the higher increase in the interfacial resistance of other gel polymer electrolytes. The prototype cell (MCMB/PVdF-based fibrous electrolyte/LiCoO{sub 2}) showed a very stable charge-discharge behavior with a slight capacity loss under constant current and voltage conditions at the C/2-rate of 20 and 60 deg. C.

  15. Superacid-Based Lithium Salts For Polymer Electrolytes

    Science.gov (United States)

    Nagasubramanian, Ganesan; Prakash, Surya; Shen, David H.; Surampudi, Subbarao; Olah, George

    1995-01-01

    Solid polymer electrolytes exhibiting high lithium-ion conductivities made by incorporating salts of superacids into thin films of polyethylene oxide (PEO). These and other solid-polymer electrolytes candidates for use in rechargeable lithium-based electrochemical cells. Increases in room-temperature lithium-ion conductivities of solid electrolytes desirable because they increase achievable power and energy densities.

  16. Effect of the alkaline cation size on the conductivity in gel polymer electrolytes and their influence on photo electrochemical solar cells.

    Science.gov (United States)

    Bandara, T M W J; Fernando, H D N S; Furlani, M; Albinsson, I; Dissanayake, M A K L; Ratnasekera, J L; Mellander, B-E

    2016-04-28

    The nature and concentration of cationic species in the electrolyte exert a profound influence on the efficiency of nanocrystalline dye-sensitized solar cells (DSSCs). A series of DSSCs based on gel electrolytes containing five alkali iodide salts (LiI, NaI, KI, RbI and CsI) and polyacrylonitrile with plasticizers were fabricated and studied, in order to investigate the dependence of solar cell performance on the cation size. The ionic conductivity of electrolytes with relatively large cations, K(+), Rb(+) and Cs(+), was higher and essentially constant, while for the electrolytes containing the two smaller cations, Na(+) and Li(+), the conductivity values were lower. The temperature dependence of conductivity in this series appears to follow the Vogel-Tamman-Fulcher equation. The sample containing the smallest cation shows the lowest conductivity and the highest activation energy of ∼36.5 meV, while K(+), Rb(+) and Cs(+) containing samples show an activation energy of ∼30.5 meV. DSSCs based on the gel electrolyte and a TiO2 double layer with the N719 dye exhibited an enhancement in the open circuit voltage with increasing cation size. This can be attributed to the decrease in the recombination rate of electrons and to the conduction band shift resulting from cation adsorption by TiO2. The maximum efficiency value, 3.48%, was obtained for the CsI containing cell. The efficiencies shown in this study are lower compared to values reported in the literature, and this can be attributed to the use of a single salt and the absence of other additives, since the focus of the present study was to analyze the cation effect. The highest short circuit current density of 9.43 mA cm(-2) was shown by the RbI containing cell. The enhancement of the solar cell performance with increasing size of the cation is discussed in terms of the effect of the cations on the TiO2 anode and ion transport in the electrolyte. In liquid electrolyte based DSSCs, the short circuit current density

  17. Development and manufacture of printable next-generation gel polymer ionic liquid electrolyte for Zn/MnO2 batteries

    Science.gov (United States)

    Winslow, R.; Wu, C. H.; Wang, Z.; Kim, B.; Keif, M.; Evans, J.; Wright, P.

    2013-12-01

    While much energy storage research focuses on the performance of individual components, such as the electrolyte or a single electrode, few investigate the electrochemical system as a whole. This research reports on the design, composition, and performance of a Zn/MnO2 battery as affected by the manufacturing method and next-generation gel polymer electrolyte composed of the ionic liquid [BMIM][Otf], ZnOtf salt, and PVDF-HFP polymer binder. Materials and manufacturing tests are discussed with a focus on water concentration, surface features as produced by printing processes, and the effect of including a gel polymer phase. Cells produced for this research generated open circuit voltages from 1.0 to 1.3 V. A dry [BMIM][Otf] electrolyte was found to have 87.3 ppm of H2O, while an electrolyte produced in ambient conditions contained 12400 ppm of H2O. Cells produced in a dry, Ar environment had an average discharge capacity of 0.0137 mAh/cm2, while one produced in an ambient environment exhibited a discharge capacity at 0.05 mAh/cm2. Surface features varied significantly by printing method, where a doctor blade produced the most consistent features. The preliminary results herein suggest that water, surface roughness, and the gel polymer play important roles in affecting the performance of printed energy storage.

  18. Dynamic tafel factor adaption for the evaluation of instantaneous corrosion rates on zinc by using gel-type electrolytes

    Science.gov (United States)

    Babutzka, M.; Heyn, A.

    2017-03-01

    Electrochemical corrosion measurements allow calculation of the instantaneous zinc corrosion rate via polarization resistances by using tafel factors. However, the determination of the actual tafel factor is problematic since it depends on the state of the formed zinc layers and the corrosion reactions taking place. Therefore, valid tafel factors are either determined in additional experiments via dynamic polarization or estimated by calculation. In most cases a constant value for tafel factors is assumed for simplification, without regard to the real conditions of the corroding system. Since naturally formed zinc layers are unstable using conventional test electrolyte solutions determination of tafel factors is hindered additionally and inaccurate interpretations can result. For some time now, the use of gel-type electrolytes in corrosion research has enabled minimally invasive investigation of zinc surface layers and thus offers new approaches to a scientifically proven determination of tafel factors. The paper presents a new method for the determination and evaluation of tafel factors using gel-type electrolytes and electrochemical frequency modulation technique (EFM). This relatively new electrochemical method offers the possibility to determine both polarization resistances and tafel factors within one measurement and in short measuring intervals. Starting from a comprehensive parameter study it is shown that a direct relationship between the two values exists that can be described mathematically. This contribution presents the determined tafel factors for the system gel-type electrolyte/zinc and discusses their applicability and their limits.

  19. ZnCl{sub 2}- and NH{sub 4}Cl-hydroponics gel electrolytes for zinc-carbon batteries

    Energy Technology Data Exchange (ETDEWEB)

    Khalid, N.H.; Ismail, Y.M. Baba; Mohamad, A.A. [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

    2008-01-21

    Absorbency testing is used to determine the percentage of ZnCl{sub 2} or NH{sub 4}Cl solution absorbed by a hydroponics gel (HPG). It is found that the absorbency of ZnCl{sub 2} or NH{sub 4}Cl solution decreases with increasing solution concentration. The conductivity of ZnCl{sub 2}- and NH{sub 4}Cl-HPG electrolytes is dependent on the solution concentration. A mixture of salt solution with HPG yields excellent gel polymer electrolytes with conductivities of 0.026 and 0.104 S cm{sup -1} at 3 M ZnCl{sub 2} and 7 M NH{sub 4}Cl, respectively. These gel electrolytes are then used to produce zinc-carbon cells. The fabricated cells give capacities of 8.8 and 10.0 mAh, have an internal resistance of 25.4 and 19.8 {omega}, a maximum power density of 12.7 and 12.2 mW cm{sup -2}, and a short-circuit current density of 29.1 and 33.9 mA cm{sup -2} for ZnCl{sub 2}- and NH{sub 4}Cl-HPG electrolytes, respectively. (author)

  20. ZnCl 2- and NH 4Cl-hydroponics gel electrolytes for zinc-carbon batteries

    Science.gov (United States)

    Khalid, N. H.; Ismail, Y. M. Baba; Mohamad, A. A.

    Absorbency testing is used to determine the percentage of ZnCl 2 or NH 4Cl solution absorbed by a hydroponics gel (HPG). It is found that the absorbency of ZnCl 2 or NH 4Cl solution decreases with increasing solution concentration. The conductivity of ZnCl 2- and NH 4Cl-HPG electrolytes is dependent on the solution concentration. A mixture of salt solution with HPG yields excellent gel polymer electrolytes with conductivities of 0.026 and 0.104 S cm -1 at 3 M ZnCl 2 and 7 M NH 4Cl, respectively. These gel electrolytes are then used to produce zinc-carbon cells. The fabricated cells give capacities of 8.8 and 10.0 mAh, have an internal resistance of 25.4 and 19.8 Ω, a maximum power density of 12.7 and 12.2 mW cm -2, and a short-circuit current density of 29.1 and 33.9 mA cm -2 for ZnCl 2- and NH 4Cl-HPG electrolytes, respectively.

  1. Performance of flexible capacitors based on polypyrrole/carbon fiber electrochemically prepared from various phosphate electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Wei; Han, Gaoyi, E-mail: han_gaoyis@sxu.edu.cn; Chang, Yunzhen; Li, Miaoyu; Xiao, Yaoming, E-mail: ymxiao@sxu.edu.cn; Zhou, Haihan; Zhang, Ying; Li, Yanping

    2016-11-30

    Highlights: • PPy/CFs have been fabricated by electrodepositing polypyrrole on carbon fibers. • The electrolytes in deposition solution have effect on PPy/CFs’ capacitive behavior. • Cells of PPy/CFs obtained from NaH{sub 2}PO{sub 4} electrolyte has good stability in PVA/H{sub 3}PO{sub 4}. - Abstract: In order to investigate the influence of electrolytes in electro-deposition solution on the capacitive properties of polypyrrole (PPy), we have chosen phosphoric acid, phosphate, hydrogen phosphate and dihydrogen phosphate as electrolyte in deposition solution respectively and electrochemically deposited PPy on carbon fibers (CFs) via galvanostatic method. The morphologies of the PPy/CFs samples have been characterized by scanning electron microscope. The specific capacitance of PPy/CFs samples has been evaluated in different electrolytes through three-electrode test system. The assembled flexible capacitors by using PPy/CFs as electrodes and H{sub 3}PO{sub 4}/polyvinyl alcohol as gel electrolyte have been systematically measured by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy. The results show that the electrochemical capacitors based on PPy/CFs prepared from deposition solution containing NaH{sub 2}PO{sub 4}·2H{sub 2}O electrolyte exhibit higher specific capacitance, flexibility and excellent stability (retaining 96.8% of initial capacitance after 13,000 cycles), and that three cells connected in series can power a light-emitting diode.

  2. Nano-composite polymer gel electrolytes containing ortho-nitro benzoic acid: role of dielectric constant of solvent and fumed silica

    Science.gov (United States)

    Kumar, R.

    2015-03-01

    In this paper, nano-composite polymer gel electrolytes containing polymethylmethacrylate, dimethylacetamide, diethyl carbonate, fumed silica and ortho-nitro benzoic acid have been synthesized. Electrical conductivity, viscosity, pH and thermal behavior of these electrolytes have been studied. The effect of acid, polymer, fumed silica concentration on conductivity, pH and viscosity has been discussed. The effect of dielectric constant of solvent on conductivity behavior of composite polymer gel electrolytes has also been studied. Two maxima in conductivity behavior have been observed with fumed silica concentration for composite polymer gel electrolytes, which have been explained on the basis of double percolation threshold model. Maximum conductivity of 3.20 × 10-4 and 2.46 × 10-6 S/cm at room temperature has been observed for nano-composite polymer gel electrolytes containing 10 wt% polymethylmethacrylate in 1 M solution of o-nitro benzoic acid in dimethylacetamide and diethyl carbonate respectively. The intensity of first maximum observed in conductivity at low concentration of fumed silica has been found to decrease with the decrease in acid concentration for composite polymer gel electrolytes, while the intensity of second maximum at higher fumed silica concentration remains unaffected. The conductivity of composite gels does not show much change in the temperature range of 20-100 °C and also remains constant with time, making them suitable for use as electrolytes in various devices like fuel cells, proton batteries, electrochromic window applications etc.

  3. Dye-sensitized solar cell with natural gel polymer electrolytes and f-MWCNT as counter-electrode

    Science.gov (United States)

    Nwanya, A. C.; Amaechi, C. I.; Ekwealor, A. B. C.; Osuji, R. U.; Maaza, M.; Ezema, F. I.

    2015-05-01

    Samples of DSSCs were made with gel polymer electrolytes using agar, gelatin and DNA as the polymer hosts. Anthocyanine dye from Hildegardia barteri flower is used to sensitize the TiO2 electrode, and the spectrum of the dye indicates strong absorptions in the blue region of the solar spectrum. The XRD pattern of the TiO2 shows that the adsorption of the dye did not affect the crystallinity of the electrode. The f-MWCNT indicates graphite structure of the MWCNTs were acid oxidized without significant damage. Efficiencies of 3.38 and 0.1% were obtained using gelatin and DNA gel polymer electrolytes, respectively, for the fabricated dye-sensitized solar cells.

  4. Zinc-air cell with KOH-treated agar layer between electrode and electrolyte containing hydroponics gel

    Energy Technology Data Exchange (ETDEWEB)

    Otham, R. [International Islamic University, Kuala Lumpur (Malaysia); Yahaya, A. H. [University of Malaya, Dept. of Chemistry, Kuala Lumpur (Malaysia); Arof, A. K. [University of Malaya, Dept. of Physics, Kuala Lumpur (Malaysia)

    2002-07-01

    Zinc-air electrochemical power sources possess the highest density compared to other zinc anode batteries, due their free and unlimited supply from the ambient air. In this experiment zinc-air cells have been fabricated employing hydroponics gel as an alternative alkaline electrolyte gelling agent. Thin KOH-treated agar layer was applied between the electrode-electrolyte interfaces which produced significant enhancement of the cells' capacities, indicating that the application of thin agar layer will improve the electrode-gelled electrolyte interfaces. Promising results have been achieved with porous zinc anode prepared from dried zinc-graphite-gelatinized agar paste; e g. a zinc-air cell employing a porous zinc anode has demonstrated a capacity of 1470 mAh rated at 0.1 A continuous discharge. 32 refs., 9 figs.

  5. Two distinct lithium diffusive species for polymer gel electrolytes containing LiBF₄, propylene carbonate (PC) and PVDF

    OpenAIRE

    Richardson, PM; Voice, AM; Ward, IM

    2014-01-01

    Polymer gel electrolytes have been prepared using lithium tetrafluoroborate (LiBF₄), propylene carbonate (PC) and polyvinylidene fluoride (PVDF) at 20% and 30% concentration by mass. Self diffusion coefficients have been measured using pulse field gradient nuclear magnetic resonance (PFG-NMR) for the cation and anion using ⁷Li and ¹⁹F resonant frequencies respectively. It was found that lithium ion diffusion was slow compared to the much larger fluorine anion likely resulting from a large sol...

  6. Study on properties of gel polymer electrolytes of PVDF-HFP%凝胶聚合物PVDF-HFP电解质膜的性能研究

    Institute of Scientific and Technical Information of China (English)

    芮含笑; 乔庆东; 李琪

    2012-01-01

    The lithium ion batteries are commercialized due to their shape versatility, flexibility, and lightness and can meet the demands of microelectronic industries. Poly (vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) is one of the most popular polymers for gel polymer electrolytes (GPE) because of its high ionic conductivity, good mechanical, thermal, interfacial, and electrochemical stabilities. In this paper, the progress and the composition of solid polymer electrolyte based on PVDF-HFP was reviewed briefly and the preparation technology of the polymer electrolyte was introduced. The influences on the properties of the polymer electrolyte were analyzed. The progress of modified the polymer electrolyte were discussed, including the modification of filler, plasticizer, polymer, . Copolymerization and blending technologies. The development of polymer electrolyte in the future was also suggested.%锂离子电池由于形状多样化、灵活性及轻便等优点而用于商业化生产,满足微型电子工业的需要,而偏氟乙烯和六氟丙烯的共聚物PVDF-HFP由于较高的电导率,较好的机械强度和热稳定性,优良的界面特性和电化学性能而被认为是最受欢迎的一种聚合物电解质.主要综述了PVDF-HFP固体电解质的组成、制备方法和进展,讨论了PVDF-HFP电解质的改性措施:填料改性、增塑剂改性、共聚共混改性及聚合物改性.对今后的发展方向作了简单展望.

  7. Development of dye-sensitized solar cells composed of liquid crystal embedded, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers as polymer gel electrolytes.

    Science.gov (United States)

    Ahn, Sung Kwang; Ban, Taewon; Sakthivel, P; Lee, Jae Wook; Gal, Yeong-Soon; Lee, Jin-Kook; Kim, Mi-Ra; Jin, Sung-Ho

    2012-04-01

    In order to overcome the problems associated with the use of liquid electrolytes in dye-sensitized solar cells (DSSCs), a new system composed of liquid crystal embedded, polymer electrolytes has been developed. For this purpose, three types of DSSCs have been fabricated. The cells contain electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (e-PVdF-co-HFP) polymer gel electrolyte, with and without doping with the liquid crystal E7 and with a liquid electrolyte. The morphologies of the newly prepared DSSCs were explored using field emission scanning electron microscopy (FE-SEM). Analysis of the FE-SEM images indicate that the DSSC composed of E7 embedded on e-PVdF-co-HFP polymer gel electrolyte has a greatly regular morphology with an average diameter. The ionic conductivity of E7 embedded on e-PVdF-co-HFP polymer gel electrolyte was found to be 2.9 × 10(-3) S/cm at room temperature, a value that is 37% higher than that of e-PVdF-co-HFP polymer gel electrolyte. The DCCS containing the E7 embedded, e-PVdF-co-HFP polymer gel electrolyte was observed to possess a much higher power conversion efficiency (PCE = 6.82%) than that of an e-PVdF-co-HFP nanofiber (6.35%). In addition, DSSCs parameters of the E7 embedded, e-PVdF-co-HFP polymer gel electrolyte (V(oc) = 0.72 V, J(sc) = 14.62 mA/cm(2), FF = 64.8%, and PCE = 6.82% at 1 sun intensity) are comparable to those of a liquid electrolyte (V(oc) = 0.75 V, J(sc) = 14.71 mA/cm(2), FF = 64.9%, and PCE = 7.17%, both at a 1 sun intensity).

  8. Polypyrrole/poly(vinyl alcohol-co-ethylene) quasi-solid gel electrolyte for iodine-free dye-sensitized solar cells

    Science.gov (United States)

    Jung, Mi-Hee

    2014-12-01

    Conducting polymer gel electrolyte is synthesized using the Cl- doped polypyrrole (PPy)/1-buty-2,3-dimethylimidazolium iodide (BDI)/poly(vinyl alcohol-co-ethylene)(PVA-EL), which yield an overall energy-conversion efficiency of about 4.72% comparable to the liquid electrolyte 4.69% under irradiation at 100 mW cm-2 AM 1.5. The introduction of PPy and PVA-EL into the BDI (which dissolves in the dimethylsulfoxide) increases the ion conductivity and effectively decreases the charge transfer resistance in the PPy gel electrolyte/TiO2/dye interfaces. With the change of the PVA-EL composition, PPy gel electrolyte exhibits independence of the content of PVA-EL, which means ion conductivity of PPy gel electrolyte as a dominant role for the contribution of cell performance. Employing intensity-modulated photo-voltage spectroscopy, intensity-modulated photo-current spectroscopy, and charge-extraction measurement, it demonstrate that the effective charge collection in PPy gel electrolyte devices rather than liquid electrolyte one is occurred due to the larger diffusion coefficient and long electron lifetime, resulting in the higher-efficiency solar cell.

  9. Novel polymer gel electrolyte with organic solvents for quasi-solid-state dye-sensitized solar cells.

    Science.gov (United States)

    Shen, Sheng-Yen; Dong, Rui-Xuan; Shih, Po-Ta; Ramamurthy, Vittal; Lin, Jiang-Jen; Ho, Kuo-Chuan

    2014-11-12

    A cross-linked copolymer was previously synthesized from poly(oxyethylene) diamine (POE-amine) and an aromatic anhydride and cured to generate an amide-imide cross-linking structure. The copolymer containing several chemical groups such as POE, amido acids, and imide, enabled to absorb liquid electrolytes in methoxypropionitrile (MPN) for suitable uses in dye-sensitized solar cells. To establish the advantages of polymer gel electrolytes (PGE), the same copolymer was studied by using different electrolyte solvents including propylene carbonate (PC), dimethylformamide, and N-methyl-2-pyrrolidone, and shown their long-term stability. The morphology of the copolymer after absorbing liquid electrolytes in these solvents was proven the same as a 3D interconnected nanochannels, evidenced field emission-scanning electron microscopy. Among these solvents, PC was selected as the optimized PGE, which demostrated a higher power conversion efficiency (8.31%) than that of the liquid electrolyte (7.89%). In particular, the long-term stability of only a 5% decrease in the cell efficiency after 1000 h of testing was achieved. It was proven the developed copolymer as PGE was versatile for different solvents showing high efficiency and long-term durability.

  10. Hyperbranched Polymer-Based Electrolyte for Lithium Polymer Batteries

    Institute of Scientific and Technical Information of China (English)

    Takahito Itoh

    2005-01-01

    @@ 1Introduction Solid polymer electrolytes have attracted much attention as electrolyte materials for all solid-state recharge able lithium batteries, and poly ( ethylene oxide) ( PEO)-based polymer electrolytes are among the most intensively studied systems[1-3]. Hyperbranched polymers have unique properties such as completely amorphous, highly soluble in common organic solvent and processible because of the highly branched nature[4,5].

  11. Effect of The Addition of PEG and PVA Polymer for Gel Electrolytes in Dye-Sensitized Solar Cell (DSSC) with Chlorophyll as Dye Sensitizer

    Science.gov (United States)

    Seni, Ramadhanti S.; Puspitasari, Nurrisma; Endarko

    2017-07-01

    Dye-sensitized Solar Cell (DSSC) is a third-generation solar cell that consists of a working electrode, electrolyte and counter electrode. One of the most important parts of DSSC is an electrolyte that roles as a medium and regenerates the electron transport of electrons in the dye. However, the liquid electrolyte has a lack of stability in long-term use and easily evaporate or leak in DSSC. Therefore, this study aims to investigate an effect of the addition of polymer material such as PEG 1000, 4000 and PVA 60000 for fabricating a gel electrolyte to solve the problems of liquid electrolyte. The synthesized TiO2 nanoparticles used in this study was prepared using co-precipitation (CPT) method which produces TiO2 anatase phase with a crystal size of 11.1 nm. DSSC has been successfully conducted and analyzed to evaluate its performance. The results showed that the efficiency of DSSC cells using gel electrolyte prepared with PVA 60000 was better than a liquid electrolyte, PEG 1000, 4000, with the efficiency could be obtained at 0.083, 0.018, 0.033, and 0.054%, respectively. The results demonstrated that the addition PEG and/or PVA could be enhanced the performance of DSSC due to gel electrolyte produced current and voltage more stable compared to the liquid electrolyte.

  12. UV-cured methacrylic membranes as novel gel-polymer electrolyte for Li-ion batteries

    Science.gov (United States)

    Nair, J. R.; Gerbaldi, C.; Meligrana, G.; Bongiovanni, R.; Bodoardo, S.; Penazzi, N.; Reale, P.; Gentili, V.

    In this paper, we report the synthesis and characterisation of novel methacrylic based polymer electrolyte membranes for lithium batteries. The method adopted for preparing the solid polymer electrolyte was the UV-curing process, which is well known for being easy, low cost, fast and reliable. It consists of a free radical photo polymerisation of poly-functional monomers: Bisphenol A ethoxylate (15 EO/phenol) dimethacrylate (BEMA) was chosen, as it can readily form flexible 3D networks and has long poly-ethoxy chains which can enhance the movement of Li +-ions inside the polymer matrix. The preliminary results reported here refer to systems where LiPF 6 solutions swelled the preformed polymer membranes. The tests on the conductivity, stability and cyclability of the membranes put in evidence the importance of the polymerisation in presence of mono-methacrylates acting as reactive diluents. Good values of ionic conductivity have been found, especially at ambient temperature. Much better results can be expected by choosing an appropriate mono-methacrylate to modify the polymeric membrane properties and by modifying the methodology of Li +-ions incorporation inside the polymer matrix.

  13. Preliminary Evaluations of Polymer-based Lithium Battery Electrolytes Under Development for the Polymer Electrolyte Rechargeable Systems Program

    Science.gov (United States)

    Manzo, Michelle A.; Bennett, William R.

    2003-01-01

    A component screening facility has been established at The NASA Glenn Research Center (GRC) to evaluate candidate materials for next generation, lithium-based, polymer electrolyte batteries for aerospace applications. Procedures have been implemented to provide standardized measurements of critical electrolyte properties. These include ionic conductivity, electronic resistivity, electrochemical stability window, cation transference number, salt diffusion coefficient and lithium plating efficiency. Preliminary results for poly(ethy1ene oxide)-based polymer electrolyte and commercial liquid electrolyte are presented.

  14. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G.; Lee, Yoon-Sung; Kim, Dong-Won

    2016-05-01

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures.

  15. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries.

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G; Lee, Yoon-Sung; Kim, Dong-Won

    2016-05-18

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures.

  16. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G.; Lee, Yoon-Sung; Kim, Dong-Won

    2016-01-01

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures. PMID:27189842

  17. Performance Improvements of DSSC with EB Irradiated PAN/PEO-based Gel Electrolyte%电子辐照改性PAN/PEO基体凝胶电解质对染料敏化太阳电池性能的提高

    Institute of Scientific and Technical Information of China (English)

    马艺准; 周明; 李远飞; 缑洁; 盛彦斌; 朱亚滨; 王志光; 申铁龙; 庞立龙; 宋银; 孙建荣; 姚存峰; 魏孔芳

    2011-01-01

    采用电子束(EB)对聚丙烯腈/聚氧化乙烯(PAN/PEO)凝胶电解质进行了剂量为13~260kGy的辐照,并对辐照改性的电解质组装的染料敏化太阳电池(DSSC)进行了性能测量。结果表明,改性后的DSSC的光电转化效率比改性前的高;并且随EB辐照剂量的增加,DSSC效率先迅速增加(0~65kGy),然后缓慢减小(65~130kGy)直至趋于一个平衡值(130~260kGy)。提升DSSC效率的最佳辐照剂量为65kGy,此时效率提高了约36%。对比DSSC短路电流、开路电压和填充因子随辐照剂量的变化,发现DSSC效率的提高主要是由短路电流的提高引起的。测量表明,辐照改性后的DSSC时间稳定性得到了改善,并且辐照剂量越高,稳定性的改善越明显。%In this work,PAN/PEO(polyacrylonitrile/polyethylene oxide)-based gel electrolyte was irradiated by electron beam(EB) with dose from 13 to 260 kGy.Then,DSSC(dye-sensitized solar cell) was fabricated by the irradiated electrolyte and characterized.The results show that the efficiency of the DSSC fabricated by irradiated electrolyte is promoted comparing with DSSC fabricated by un-irradiated electrolyte.And with irradiation dose increasing,the DSSC efficiency increases rapidly at first(0~65 kGy),then,drops down slowly(65~130 kGy),finally trends to a stable value(130~260 kGy).It indicates that there is an optimal irradiation dose,at which the promotion of DSSC efficiency is the highest,approximate 36%.Observed from the change of short-circuit current,open-circuit voltage and fill factor,short-circuit current promotion by EB irradiation is found to be the main reason of DSSC performance promotion.The time stability measurement of the DSSC indicates that EB irradiation on PAN/PEO electrolyte reduces the loss of efficiency and the limiting-effects become more apparent as the irradiation dose increases.

  18. Preparation and characterization of PAN–KI complexed gel polymer electrolytes for solid-state battery applications

    Indian Academy of Sciences (India)

    N KRISHNA JYOTHI; K K VENKATARATNAM; P NARAYANA MURTY; K VIJAYA KUMAR

    2016-08-01

    The free standing and dimensionally stable gel polymer electrolyte films of polyacrylonitrile (PAN): potassium iodide (KI) of different compositions, using ethylene carbonate as a plasticizer and dimethyl formamide as solvent, are prepared by adopting ‘solution casting technique’ and these films are examined for their conductivities. The structural, miscibility and the chemical rapport between PAN and KI are investigated using X-ray diffraction, Fourier transform infrared spectroscopy and differential scanning calorimetry methods. The conductivity is enhanced with the increase in KI concentration and temperature. The maximum conductivity at 30$^{\\circ}$C is found to be $2.089 \\times 10^{−5}$ S cm$^{−1}$ for PAN:KI (70:30) wt%, which is nine orders greater than that of pure PAN (${\\lt}10^{−14}$ S cm$^{−1}$). The conductivity-temperature dependence of these polymer electrolyte films obeys Arrhenius behaviour with activation energy ranging from 0.358 to 0.478 eV. The conducting carriers of charge transport in these polymer electrolyte films are identified by Wagner’s polarization technique and it is found that the charge transport is predominantlydue to ions. The better conducting sample is used to fabricate the battery with configuration K/PAN $+$ KI/I$_2$ $+$ C $+$ electrolyte and good discharge characteristics of battery are observed.

  19. Substrate integrated Lead-Carbon hybrid ultracapacitor with flooded, absorbent glass mat and silica-gel electrolyte configurations

    Indian Academy of Sciences (India)

    A Banerjee; M K Ravikumar; A Jalajakshi; P Suresh Kumar; S A Gaffoor; A K Shukla

    2012-07-01

    Lead-Carbon hybrid ultracapacitors (Pb-C HUCs) with flooded, absorbent-glass-mat (AGM) and silica-gel sulphuric acid electrolyte configurations are developed and performance tested. Pb-C HUCs comprise substrate-integrated PbO2 (SI-PbO2) as positive electrodes and high surface-area carbon with graphite-sheet substrate as negative electrodes. The electrode and silica-gel electrolyte materials are characterized by XRD, XPS, SEM, TEM, Rheometry, BET surface area, and FTIR spectroscopy in conjunction with electrochemistry. Electrochemical performance of SI-PbO2 and carbon electrodes is studied using cyclic voltammetry with constant-current charge and discharge techniques by assembling symmetric electrical-double-layer capacitors and hybrid Pb-C HUCs with a dynamic Pb(porous)/PbSO4 reference electrode. The specific capacitance values for 2 V Pb-C HUCs are found to be 166 F/g, 102 F/g and 152 F/g with a faradaic efficiency of 98%, 92% and 88% for flooded, AGM and gel configurations, respectively.

  20. Study of the interfacial stability of PVdF/HFP gel electrolytes with sub-micro- and nano-sized surface-modified silicas

    Energy Technology Data Exchange (ETDEWEB)

    Zalewska, A., E-mail: aldona@ch.pw.edu.p [Warsaw University of Technology, Department of Chemistry, Noakowskiego 3, 00-664 Warszawa (Poland); Walkowiak, M. [Institute of Non-Ferrous Metals Branch in Poznan Central Laboratory of Batteries and Cells, Forteczna 12, 61-362 Poznan (Poland); Niedzicki, L. [Warsaw University of Technology, Department of Chemistry, Noakowskiego 3, 00-664 Warszawa (Poland); Jesionowski, T. [Poznan University of Technology, Institute of Chemical Technology and Engineering, Pl. Marii Sklodowskiej-Curie 2, 60-965 Poznan (Poland); Langwald, N. [Warsaw University of Technology, Department of Chemistry, Noakowskiego 3, 00-664 Warszawa (Poland)

    2010-01-25

    The aim of the presented work was to perform a preliminary study of the physicochemical and interfacial properties of hybrid organic-inorganic gel electrolytes for Li-ion batteries based on the PVdF/HFP polymeric matrix and surface-modified silicas. Two types of silica fillers of different grain sizes (>500 nm and approx100 nm) were used as additives. The silica particles were modified by two different functional groups, i.e. methacryloxy and vinyl ones. The gel electrolytes based on PVdF/HFP copolymer were prepared according to the so-called Bellcore two-step process. The motivation of the present work was to study more deeply those systems in terms of morphology by means of scanning electron microscopy techniques. Fillers modified with identical functional groups but differing fundamentally in the manufacturing processes were compared in terms of the impact on morphology and electrochemical performance of the resulting membranes. Interfacial properties were examined by means of impedance spectroscopy technique using Swagelok-type cells with two lithium electrodes.

  1. All-solid-state supercapacitors with poly(3,4-ethylenedioxythiophene)-coated carbon fiber paper electrodes and ionic liquid gel polymer electrolyte

    Science.gov (United States)

    Pandey, G. P.; Rastogi, A. C.; Westgate, Charles R.

    2014-01-01

    All-solid-state thin supercapacitors have been fabricated using current pulse polymerized poly(3,4-ethylenedioxythiophene) (PEDOT) over carbon fiber paper and ionic liquid based gel polymer electrolyte. The PEDOT-coated carbon paper electrodes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) which confirm the porous morphology of PEDOT at the nanoscale and a high degree of ClO4- dopant ion conjugation. The performance characteristics of the supercapacitor cells have been evaluated by ac impedance spectroscopy, cyclic voltammetry and galvanostatic charge-discharge techniques. The PEDOT electrode shows specific capacitance of ∼154.5 F g-1, which correspond to the cell area-normalized capacitance of 85 mF cm-2. The maximum specific energy and specific power of the solid-state supercapacitor cell, calculated from charge-discharge characteristics, are 6.5 Wh kg-1 and 11.3 kW kg-1, respectively. The solid-state supercapacitor shows good cycle durability and time stability. The thin, lightweight, gel electrolyte based supercapacitor shows considerable potential for low-cost, high-performance energy storage applications.

  2. Ionic-Liquid-Based Polymer Electrolytes for Battery Applications.

    Science.gov (United States)

    Osada, Irene; de Vries, Henrik; Scrosati, Bruno; Passerini, Stefano

    2016-01-11

    The advent of solid-state polymer electrolytes for application in lithium batteries took place more than four decades ago when the ability of polyethylene oxide (PEO) to dissolve suitable lithium salts was demonstrated. Since then, many modifications of this basic system have been proposed and tested, involving the addition of conventional, carbonate-based electrolytes, low molecular weight polymers, ceramic fillers, and others. This Review focuses on ternary polymer electrolytes, that is, ion-conducting systems consisting of a polymer incorporating two salts, one bearing the lithium cation and the other introducing additional anions capable of plasticizing the polymer chains. Assessing the state of the research field of solid-state, ternary polymer electrolytes, while giving background on the whole field of polymer electrolytes, this Review is expected to stimulate new thoughts and ideas on the challenges and opportunities of lithium-metal batteries.

  3. Electrodeposited polyethylenedioxythiophene with infiltrated gel electrolyte interface: a close contest of an all-solid-state supercapacitor with its liquid-state counterpart

    Science.gov (United States)

    Anothumakkool, Bihag; Torris A. T, Arun; Bhange, Siddheshwar N.; Badiger, Manohar V.; Kurungot, Sreekumar

    2014-05-01

    We report the design of an all-solid-state supercapacitor, which has charge storage characteristics closely matching that of its liquid-state counterpart even under extreme temperature and humidity conditions. The prototype is made by electro-depositing polyethylenedioxythiophene (PEDOT) onto the individual carbon fibers of a porous carbon substrate followed by intercalating the matrix with polyvinyl alcohol-sulphuric acid (PVA-H2SO4) gel electrolyte. The electrodeposited layer of PEDOT maintained a flower-like growth pattern along the threads of each carbon fiber. This morphology and the alignment of PEDOT led to an enhanced surface area and electrical conductivity, and the pores in the system enabled effective intercalation of the polymer-gel electrolyte. Thus, the established electrode-electrolyte interface nearly mimics that of its counterpart based on the liquid electrolyte. Consequently, the solid device attained very low internal resistance (1.1 Ω cm-2) and a high specific capacitance (181 F g-1) for PEDOT at a discharge current density of 0.5 A g-1. Even with a high areal capacitance of 836 mF cm-2 and volumetric capacitance of 28 F cm-3, the solid device retained a mass-specific capacitance of 111 F g-1 for PEDOT. This is in close agreement with the value displayed by the corresponding liquid-state system (112 F g-1), which was fabricated by replacing the gel electrolyte with 0.5 M H2SO4. The device also showed excellent charge-discharge stability for 12 000 cycles at 5 A g-1. The performance of the device was consistent even under wide-ranging humidity (30-80%) and temperature (-10 to 80 °C) conditions. Finally, a device fabricated by increasing the electrode area four times was used to light an LED, which validated the scalability of the process.We report the design of an all-solid-state supercapacitor, which has charge storage characteristics closely matching that of its liquid-state counterpart even under extreme temperature and humidity conditions

  4. Performance of flexible capacitors based on polypyrrole/carbon fiber electrochemically prepared from various phosphate electrolytes

    Science.gov (United States)

    Yuan, Wei; Han, Gaoyi; Chang, Yunzhen; Li, Miaoyu; Xiao, Yaoming; Zhou, Haihan; Zhang, Ying; Li, Yanping

    2016-11-01

    In order to investigate the influence of electrolytes in electro-deposition solution on the capacitive properties of polypyrrole (PPy), we have chosen phosphoric acid, phosphate, hydrogen phosphate and dihydrogen phosphate as electrolyte in deposition solution respectively and electrochemically deposited PPy on carbon fibers (CFs) via galvanostatic method. The morphologies of the PPy/CFs samples have been characterized by scanning electron microscope. The specific capacitance of PPy/CFs samples has been evaluated in different electrolytes through three-electrode test system. The assembled flexible capacitors by using PPy/CFs as electrodes and H3PO4/polyvinyl alcohol as gel electrolyte have been systematically measured by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy. The results show that the electrochemical capacitors based on PPy/CFs prepared from deposition solution containing NaH2PO4·2H2O electrolyte exhibit higher specific capacitance, flexibility and excellent stability (retaining 96.8% of initial capacitance after 13,000 cycles), and that three cells connected in series can power a light-emitting diode.

  5. Performance of electrical double layer capacitors fabricated with gel polymer electrolytes containing Li{sup +} and K{sup +}-salts: A comparison

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Manoj K., E-mail: mmanoj.ssi@gmail.com; Hashmi, S. A. [Department of Physics & Astrophysics, University of Delhi, Delhi-110007 (India)

    2015-06-24

    The comparative performance of the solid-state electrical double layer capacitors (EDLCs) based on the multiwalled carbon nanotube (MWCNT) electrodes and poly (vinaylidinefluoride-co-hexafluoropropyline) (PVdF-HFP) based gel polymer electrolytes (GPEs) containing potassium and lithium salts have been studied. The room temperature ionic conductivity of the GPEs have been found to be ∼3.8×10{sup −3} and 5.9×10{sup −3} S cm{sup −1} for lithium and potassium based systems. The performance of EDLC cells studied by impedance spectroscopy, cyclic voltammetry and constant current charge-discharge techniques, indicate that the EDLC with potassium salt containing GPE shows excellent performance almost equivalent to the EDLC with Li-salt-based GPE.

  6. Physics based Degradation Modeling and Prognostics of Electrolytic Capacitors under Electrical Overstress Conditions

    Data.gov (United States)

    National Aeronautics and Space Administration — This paper proposes a physics based degradation modeling and prognostics approach for electrolytic capacitors. Electrolytic capacitors are critical components in...

  7. Prognostics Health Management and Physics based failure Models for Electrolytic Capacitors

    Data.gov (United States)

    National Aeronautics and Space Administration — This paper proposes first principles based modeling and prognostics approach for electrolytic capacitors. Electrolytic capacitors and MOSFETs are the two major...

  8. SEM, XRD and electrical conductivity studies of PVDF-HFP-LiBF4 -EC plasticized gel polymer electrolyte

    Science.gov (United States)

    Sangeetha, M.; Mallikarjun, A.; Jaipal Reddy, M.; Siva Kumar, J.

    2017-07-01

    Micro porous gel type polymer electrolytes composed of 80 Wt% PVDF-HFP polymer - 20 Wt% LiBF4 salt in different concentrations of EC plasticizer (10Wt% - 70 Wt %) plasticizer have been synthesized by Solution cast technique. The effect of plasticizer in polymer-salt matrix, structural, morphological and ionic conductivity is studied. Structural and morphological studies showed increase in amorphous nature and recrystallization after a certain limit of EC plasticizer. The highest ionic conductivity of 1.510 × 10-3 Cm-1 is found for 40 Wt% of EC plasticizer at 303K. Addition of plasticizer increase free volume enables segmental motion of polymer and free mobility of ions. Also it provides more number of charge carriers in turn enhances the ionic conductivity up to certain limit of 40 Wt% of EC plasticizer. Further increase of plasticizer content creates ion-pair aggregation and recrystallization which reduces the ionic conductivity. The ionic conductivity obeys the VTF relationship for Gel type polymer electrolyte system.

  9. Electrochemical characterizations on MnO2 supercapacitors with potassium polyacrylate and potassium polyacrylate-co-polyacrylamide gel polymer electrolytes

    KAUST Repository

    Lee, Kuang-Tsin

    2009-11-01

    MnO2·nH2O supercapacitors with potassium polyacrylate (PAAK) and potassium polyacrylate-co-polyacrylamide (PAAK-co-PAAM) gel polymer electrolytes (GPEs) having the weight compositions of polymer:KCl:H2O = 9%:6.7%:84.3% have been characterized for their electrochemical performance. Compared with the liquid electrolyte (LE) counterpart, the GPE cells exhibit remarkable (∼50-130%) enhancement in specific capacitance of the oxide electrode, and the extent of the enhancement increases with increasing amount of the carboxylate groups in the polymers as well as with increasing oxide/electrolyte interfacial area. In situ X-ray absorption near-edge structure (XANES) analysis indicates that the oxide electrodes of the GPE cells possess higher Mn-ion valences and are subjected to greater extent of valence variation than that of the LE cell upon charging/discharging over the same potential range. Copolymerization of PAAK with PAAM greatly improves the cycling stability of the MnO2·nH2O electrode, and the improvement is attributable to the alkaline nature of the amino groups. Both GPEs exhibit ionic conductivities greater than 1.0 × 10-1 S cm-1 and are promising for high-rate applications. © 2009 Elsevier Ltd. All rights reserved.

  10. Impedance Spectroscopy and FTIR Studies of PEG - Based Polymer Electrolytes

    Directory of Open Access Journals (Sweden)

    Anji Reddy Polu

    2011-01-01

    Full Text Available Ionic conductivity of poly(ethylene glycol (PEG - ammonium chloride (NH4Cl based polymer electrolytes can be enhanced by incorporating ceramic filler TiO2 into PEG-NH4Cl matrix. The electrolyte samples were prepared by solution casting technique. FTIR studies indicates that the complex formation between the polymer, salt and ceramic filler. The ionic conductivity was measured using impedance spectroscopy technique. It was observed that the conductivity of the electrolyte varies with TiO2 concentration and temperature. The highest room temperature conductivity of the electrolyte of 7.72×10−6 S cm-1 was obtained at 15% by weight of TiO2 and that without TiO2 filler was found to be 9.58×10−7 S cm−1. The conductivity has been improved by 8 times when the TiO2 filler was introduced into the PEG–NH4Cl electrolyte system. The conductance spectra shows two distinct regions: a dc plateau and a dispersive region. The temperature dependence of the conductivity of the polymer electrolytes seems to obey the VTF relation. The conductivity values of the polymer electrolytes were reported and the results were discussed. The imaginary part of dielectric constant (εi decreases with increase in frequency in the low frequency region whereas frequency independent behavior is observed in the high frequency region.

  11. Polymer Electrolytes for Lithium/Sulfur Batteries

    Directory of Open Access Journals (Sweden)

    The Nam Long Doan

    2012-08-01

    Full Text Available This review evaluates the characteristics and advantages of employing polymer electrolytes in lithium/sulfur (Li/S batteries. The main highlights of this study constitute detailed information on the advanced developments for solid polymer electrolytes and gel polymer electrolytes, used in the lithium/sulfur battery. This includes an in-depth analysis conducted on the preparation and electrochemical characteristics of the Li/S batteries based on these polymer electrolytes.

  12. Boron cross-linked graphene oxide/polyvinyl alcohol nanocomposite gel electrolyte for flexible solid-state electric double layer capacitor with high performance

    KAUST Repository

    Huang, Yi-Fu

    2014-06-01

    A new family of boron cross-linked graphene oxide/polyvinyl alcohol (GO-B-PVA) nanocomposite gels is prepared by freeze-thaw/boron cross-linking method. Then the gel electrolytes saturated with KOH solution are assembled into electric double layer capacitors (EDLCs). Structure, thermal and mechanical properties of GO-B-PVA are explored. The electrochemical properties of EDLCs using GO-B-PVA/KOH are investigated, and compared with those using GO-PVA/KOH gel or KOH solution electrolyte. FTIR shows that boron cross-links are introduced into GO-PVA, while the boronic structure inserted into agglomerated GO sheets is demonstrated by DMA analysis. The synergy effect of the GO and the boron crosslinking benefits for ionic conductivity due to unblocking ion channels, and for improvement of thermal stability and mechanical properties of the electrolytes. Higher specific capacitance and better cycle stability of EDLCs are obtained by using the GO-B-PVA/KOH electrolyte, especially the one at higher GO content. The nanocomposite gel electrolytes with excellent electrochemical properties and solid-like character are candidates for the industrial application in high-performance flexible solid-state EDLCs. © 2014 Elsevier Ltd.

  13. The effect of the amount of electrolyte in the anode gel on the rechargeability of alkaline manganese dioxidezinc cells

    Science.gov (United States)

    Sharma, Yatendra; Haynes, Alejandro; Binder, Leo; Kordesch, Karl

    The zinc-limited anode technology for rechargeable alkaline manganese dioxidezinc cells is well known. Attempts have been made to relate the rechargeability of these cells with the amount of electrolyte available in the anode gel. The rechargeability of the cells is found to increase with the amount of electrolyte up to 35 - 40% of the dry weight of the anode mass. Further increases in the amount of electrolyte were found to be detrimental to the rechargeability of the cells. Analysis of cathodes after running several cycles shows higher amounts of zinc in those from cells with greater amounts of electrolyte. This could be due to haeterolite formation in the cathode which poisons it thus explaining the reduced rechargeability with excess electrolyte.

  14. Norbornene-Based Polymer Electrolytes for Lithium Cells

    Science.gov (United States)

    Cheung, Iris; Smart, Marshall; Prakash, Surya; Miyazawa, Akira; Hu, Jinbo

    2007-01-01

    Norbornene-based polymers have shown promise as solid electrolytes for lithium-based rechargeable electrochemical cells. These polymers are characterized as single-ion conductors. Single-ion-conducting polymers that can be used in lithium cells have long been sought. Single-ion conductors are preferred to multiple-ion conductors as solid electrolytes because concentration gradients associated with multiple-ion conduction lead to concentration polarization. By minimizing concentration polarization, one can enhance charge and discharge rates. Norbornene sulfonic acid esters have been synthesized by a ring-opening metathesis polymerization technique, using ruthenium-based catalysts. The resulting polymer structures (see figure) include sulfonate ionomers attached to the backbones of the polymer molecules. These molecules are single-ion conductors in that they conduct mobile Li+ ions only; the SO3 anions in these polymers, being tethered to the backbones, do not contribute to ionic conduction. This molecular system is especially attractive in that it is highly amenable to modification through functionalization of the backbone or copolymerization with various monomers. Polymers of this type have been blended with poly(ethylene oxide) to lend mechanical integrity to free-standing films, and the films have been fabricated into solid polymer electrolytes. These electrolytes have been demonstrated to exhibit conductivity of 2 10(exp -5)S/cm (which is high, relative to the conductivities of other solid electrolytes) at ambient temperature, plus acceptably high stability. This type of norbornene-based polymeric solid electrolyte is in the early stages of development. Inasmuch as the method of synthesis of these polymers is inherently flexible and techniques for the fabrication of the polymers into solid electrolytes are amenable to optimization, there is reason to anticipate further improvements.

  15. Ionic liquid-based membranes as electrolytes for advanced lithium polymer batteries.

    Science.gov (United States)

    Navarra, M A; Manzi, J; Lombardo, L; Panero, S; Scrosati, Bruno

    2011-01-17

    Gel-type polymer electrolytes are formed by immobilizing a solution of lithium N,N-bis(trifluoromethanesulfonyl)imide (LiTFSI) in N-n-butyl-N-ethylpyrrolidinium N,N-bis(trifluoromethanesulfonyl)imide (Py₂₄TFSI) ionic liquid (IL) with added mixtures of organic solvents, such as ethylene, propylene and dimethyl carbonates (EC, PC, and DMC, respectively), into a poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP) matrix, and their properties investigated. The addition of the organic solvent mixtures results in an improvement of the ionic conductivity and in the stabilization of the interface with the lithium electrode. Conductivity values in the range of 10⁻³-10⁻²  S cm⁻¹ are obtained in a wide temperature range. These unique properties allow the effective use of these membranes as electrolytes for the development of advanced polymer batteries based on a lithium metal anode and an olivine-type lithium iron phosphate cathode.

  16. The electrochemical redox processes in methacrylate-based polymer electrolytes II. - Study on microelectrodes

    Energy Technology Data Exchange (ETDEWEB)

    Nadherna, Martina [Institute of Inorganic Chemistry of the AS CR, v.v.i., 250 68 Husinec-Rez (Czech Republic)] [Department of Analytical Chemistry, Faculty of Science, Charles University in Prague, Albertov 2030, 128 40 Prague 2 (Czech Republic); Reiter, Jakub, E-mail: reiter@iic.cas.c [Institute of Inorganic Chemistry of the AS CR, v.v.i., 250 68 Husinec-Rez (Czech Republic)

    2010-08-01

    The electrochemical behaviour of ferrocene was studied in different gel polymer electrolytes based on methyl, ethyl and 2-ethoxyethyl methacrylate and compared to the liquid aprotic solution (propylene carbonate). Voltammetric and chronoamperometric measurements on microelectrodes were conducted in order to describe the qualitative as well as quantitative behaviour of ferrocene in different conditions. Heterogeneous electron-transfer rate constants and diffusion coefficients of ferrocene in polymer electrolytes were estimated to be 1.1-7.8 x 10{sup -3} cm s{sup -1} and 4-13 x 10{sup -8} cm{sup 2} s{sup -1} depending on the electrolyte composition. The influence of the polymer polarity, ferrocene concentration and level of polymer cross-linkage on the kinetics of ferrocene oxidation and its transport was discussed. The electrolytes with poly(2-ethoxyethyl methacrylate) exhibit the highest ionic conductivity (2-4 x 10{sup -4} S cm{sup -1}) as well as diffusion coefficient of ferrocene (1.3 x 10{sup -7} cm{sup 2} s{sup -1}) in their structure.

  17. Graphene tailored polymer gel electrolytes for 9.1%-efficiency quasi-solid-state dye-sensitized solar cells

    Science.gov (United States)

    Zheng, Jingjing

    2017-04-01

    Pursuit of technological implementation with enhanced photoelectric conversion efficiency and power generation ability in the dark is a persistent objective for dye-sensitized solar cells (DSSCs). We launch here three strategies of designing graphene tailored polymer gel electrolytes (PGEs) with an electron-conducting feature, aiming at reserving I-/I3- redox couples into three-dimensional (3D) PGE framework, reducing I3- species within the PGE and shortening the diffusion length of redox couples. The 3D PGE provides framework for I-/I3- diffusion like in a liquid system, whereas graphene experiences to form interconnected channels along polyelectrolyte backbones. The results demonstrate that a power conversion efficiency of 9.1% is yielded on the resultant quasi-solid-state DSSCs by optimizing synthesis strategies.

  18. ELectrolytes,water,acid—base imbalance

    Institute of Scientific and Technical Information of China (English)

    1993-01-01

    930044 The effect of dilution and heparin onthe blood gas analysis.JIANG Hongxi(蒋鸿鑫)et al.Beijing Friendship Hosp,Beijing,100050.Chin J Tubere & Respri Dis 1992;15(4):225-227.The effect of heparin on the measurement ofblood gases is mainly caused by dilution,whichsubstantially reduces the PCO2 and HCO3- val-ues.Excess heparin will change the pH,PCO2and HCO3- as a consequence of an alternation inH+ ion concentration.The effect of dilution onelectrolytes depends on the respective elec-trolyte concentration in diluent.Dilution re-duces the glucose value,but to a higher degreeas could be expected from a dilution effect.

  19. Effective Infiltration of Gel Polymer Electrolyte into Silicon-Coated Vertically Aligned Carbon Nanofibers as Anodes for Solid-State Lithium-Ion Batteries.

    Science.gov (United States)

    Pandey, Gaind P; Klankowski, Steven A; Li, Yonghui; Sun, Xiuzhi Susan; Wu, Judy; Rojeski, Ronald A; Li, Jun

    2015-09-23

    This study demonstrates the full infiltration of gel polymer electrolyte into silicon-coated vertically aligned carbon nanofibers (Si-VACNFs), a high-capacity 3D nanostructured anode, and the electrochemical characterization of its properties as an effective electrolyte/separator for future all-solid-state lithium-ion batteries. Two fabrication methods have been employed to form a stable interface between the gel polymer electrolyte and the Si-VACNF anode. In the first method, the drop-casted gel polymer electrolyte is able to fully infiltrate into the open space between the vertically aligned core-shell nanofibers and encapsulate/stabilize each individual nanofiber in the polymer matrix. The 3D nanostructured Si-VACNF anode shows a very high capacity of 3450 mAh g(-1) at C/10.5 (or 0.36 A g(-1)) rate and 1732 mAh g(-1) at 1C (or 3.8 A g(-1)) rate. In the second method, a preformed gel electrolyte film is sandwiched between an Si-VACNF electrode and a Li foil to form a half-cell. Most of the vertical core-shell nanofibers of the Si-VACNF anode are able to penetrate into the gel polymer film while retaining their structural integrity. The slightly lower capacity of 2800 mAh g(-1) at C/11 rate and ∼1070 mAh g(-1) at C/1.5 (or 2.6 A g(-1)) rate have been obtained, with almost no capacity fade for up to 100 cycles. Electrochemical impedance spectroscopy does not show noticeable changes after 110 cycles, further revealing the stable interface between the gel polymer electrolyte and the Si-VACNFs anode. These results show that the infiltrated flexible gel polymer electrolyte can effectively accommodate the stress/strain of the Si shell due to the large volume expansion/contraction during the charge-discharge processes, which is particularly useful for developing future flexible solid-state lithium-ion batteries incorporating Si-anodes.

  20. The sol-gel route: A versatile process for up-scaling the fabrication of gas-tight thin electrolyte layers

    Science.gov (United States)

    Viazzi, Céline; Rouessac, Vincent; Lenormand, Pascal; Julbe, Anne; Ansart, Florence; Guizard, Christian

    2011-03-01

    Sol-gel routes are often investigated and adapted to prepare, by suitable chemical modifications, submicronic powders and derived materials with controlled morphology, which cannot be obtained by conventional solid state chemistry paths. Wet chemistry methods provide attractive alternative routes because mixing of species occurs at the atomic scale. In this paper, ultrafine powders were prepared by a novel synthesis method based on the sol-gel process and were dispersed into suspensions before processing. This paper presents new developments for the preparation of functional materials like yttria-stabilized-zirconia (YSZ, 8% Y2O3) used as electrolyte for solid oxide fuel cells. YSZ thick films were coated onto porous Ni-YSZ substrates using a suspension with an optimized formulation deposited by either a dip-coating or a spin-coating process. The suspension composition is based on YSZ particles encapsulated by a zirconium alkoxide which was added with an alkoxide derived colloidal sol. The in situ growth of these colloids increases significantly the layer density after an appropriated heat treatment. The derived films were continuous, homogeneous and around 20 μm thick. The possible up-scaling of this process has been also considered and the suitable processing parameters were defined in order to obtain, at an industrial scale, homogeneous, crack-free, thick and adherent films after heat treatment at 1400 °C.

  1. Homogeneous lithium electrodeposition with pyrrolidinium-based ionic liquid electrolytes.

    Science.gov (United States)

    Grande, Lorenzo; von Zamory, Jan; Koch, Stephan L; Kalhoff, Julian; Paillard, Elie; Passerini, Stefano

    2015-03-18

    In this study, we report on the electroplating and stripping of lithium in two ionic liquid (IL) based electrolytes, namely N-butyl-N-methylpyrrolidinium bis(fluorosulfonyl) imide (Pyr14FSI) and N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr14TFSI), and mixtures thereof, both on nickel and lithium electrodes. An improved method to evaluate the Li cycling efficiency confirmed that homogeneous electroplating (and stripping) of Li is possible with TFSI-based ILs. Moreover, the presence of native surface features on lithium, directly observable via scanning electron microscope imaging, was used to demonstrate the enhanced electrolyte interphase (SEI)-forming ability, that is, fast cathodic reactivity of this class of electrolytes and the suppressed dendrite growth. Finally, the induced inhomogeneous deposition enabled us to witness the SEI cracking and revealed previously unreported bundled Li fibers below the pre-existing SEI and nonrod-shaped protuberances resulting from Li extrusion.

  2. Performance evaluation of printed LiCoO{sub 2} cathodes with PVDF-HFP gel electrolyte for lithium ion microbatteries

    Energy Technology Data Exchange (ETDEWEB)

    Park, Moon-Soo [School of Advanced Materials Science and Engineering, College of Engineering, Yonsei University, Seoul 120-749 (Korea); Samsung Electro-Mechanics Maetan-3-dong, YeongTong-gu, Suwon City, Gyeonggi Province 442-743 (Korea); Hyun, Sang-Hoon [School of Advanced Materials Science and Engineering, College of Engineering, Yonsei University, Seoul 120-749 (Korea); Nam, Sang-Cheol [Nuricell Inc., 4F, GS Caltex New Energy Development Center, 453-2, Seongnae-dong, Gangdong-gu, Seoul 134-030 (Korea); Cho, Sung Back [Advanced Technology Research Center, Agency for Defense Development, Daejeon 305-600 (Korea)

    2008-07-01

    In order to improve the discharge capacity in lithium ion microbatteries, a thick-film cathode was fabricated by a screen printing using LiCoO{sub 2} pastes. The printed cathode showed a different discharge curves when the cell was tested using various (liquid, gel and solid-state) electrolytes. When a cell test was performed with organic liquid electrolyte, the maximum discharge capacity was 200 {mu}Ah cm{sup -2}, which corresponded to approximately 133 mAh g{sup -1} when the loading weight of LiCoO{sub 2} was calculated. An all-solid-state microbattery could be assembled using sputtered LiPON electrolyte, an evaporated Li anode, and printed LiCoO{sub 2} cathode films without delamination or electrical problems. However, the highest discharge capacity showed a very small value (7 {mu}Ah cm{sup -2}). This problem could be improved using a poly(vinylidene fluoride-hexafluoro propylene) (PVDF-HFP) gel electrolyte, which enhanced the contact area and adhesion force between cathode and electrolyte. The discharge value of this cell was measured as approximately 164 {mu}Ah cm{sup -2} ({approx}110 mAh g{sup -1}). As the PVDF-HFP electrolyte had a relatively soft contact property with higher ionic conductance, the cell performance was improved. In addition, the cell can be fabricated in a leakage-free process, which can resolve many safety problems. According to these results, there is a significant possibility that a film prepared using the aforementioned paste with screen printing and PVDF-HFP gel electrolyte is feasible for a microbattery. (author)

  3. Poly(hydroxyethyl methacrylate) based networked solid polymer electrolyte.

    Science.gov (United States)

    Lee, A-Ran; Kim, Young-Deok; Lee, Sang-Keol; Jo, Nam-Ju

    2013-10-01

    Solid polymer electrolytes (SPEs) have good safety for lithium battery compared to liquid electrolytes, but they have low ionic conductivity. To solve the problem, the polymer-in-salt system was introduced which has higher ionic conductivity than salt-in-polymer system. However, polymer-in-salt system has disadvantages that are poor mechanical properties with increasing salt concentration. In this study, networked polymer electrolytes consisting of poly(hydroxyethyl methacrylate) (P(HEMA)), lithium triflate (LiCF3SO3, LiTf) and hydrochloric acid (HCl) were prepared. And the electrochemical and mechanical properties of P(HEMA) based SPEs were investigated by using ac impedance analyzer and universal testing machine, respectively.

  4. Novel Non-Carbonate Based Electrolytes for Silicon Anodes

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Ye [Wildcat Discovery Technologies, San Diego, CA (United States); Yang, Johnny [Wildcat Discovery Technologies, San Diego, CA (United States); Cheng, Gang [Wildcat Discovery Technologies, San Diego, CA (United States); Carroll, Kyler [Wildcat Discovery Technologies, San Diego, CA (United States); Clemons, Owen [Wildcat Discovery Technologies, San Diego, CA (United States); Strand, Diedre [Wildcat Discovery Technologies, San Diego, CA (United States)

    2016-09-09

    Substantial improvement in the energy density of rechargeable lithium batteries is required to meet the future needs for electric and plug-in electric vehicles (EV and PHEV). Present day lithium ion battery technology is based on shuttling lithium between graphitic carbon and inorganic oxides. Non-graphitic anodes, such as silicon can provide significant improvements in energy density but are currently limited in cycle life due to reactivity with the electrolyte. Wildcat/3M proposes the development of non-carbonate electrolyte formulations tailored for silicon alloy anodes. Combining these electrolytes with 3M’s anode and an NMC cathode will enable up to a 20% increase in the volumetric cell energy density, while still meeting the PHEV/EV cell level cycle/calendar life goals.

  5. Stabilized γ-BIMNVOX solid electrolyte: Ethylene glycol–citrate sol–gel synthesis, microwave-assisted calcination, and structural and electrical characterization

    Energy Technology Data Exchange (ETDEWEB)

    Al-Areqi, Niyazi A.S., E-mail: niyazi.alareqi@gmail.com [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Beg, Saba [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Al-Alas, Ahlam [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Hafeez, Shehla [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India)

    2013-12-25

    Highlights: •γ-BIMNVOX was synthesized by ethylene glycol–citrate sol–gel route. •γ-BIMNVOX crystallizes by 25-min microwave-assisted calcination. •Smaller particle sizes for microwave calcined BIMNVOX samples. •Best oxide-ion performance for microwave calcined BIMNVOX samples. -- Abstract: Samples of γ-BIMNVOX (Bi{sub 2}V{sub 1−x}Mn{sub x}O{sub 5.5−x/2}; 0.13 ⩽ x ⩽ 0.20) system were synthesized by an ethylene glycol–citrate sol–gel route. The resulting xerogels were then calcined by the microwave heating using a modified domestic microwave oven operated at 2.45 GHz. Microwave-assisted calcination samples in comparison with other conventionally calcined samples were characterized in terms of phase crystallization, stabilization and particle size using simultaneous thermogravimetric–differential thermal analysis (TG–DTA), X-ray powder diffraction (XRPD) and scanning electron microscopy (SEM). The AC impedance spectroscopy was employed for electrical characterization. It was found that the microwave-assisted calcination route successfully produces better crystalline stabilized γ-BIMNVOX samples with appreciably small average particle sizes after only 25 min of microwave heating. The electrical properties of microwave calcined γ-BIMNVOX system make it an advanced low-temperature solid electrolyte suitable for use in oxide-ion based electrochemical applications.

  6. Lithium air batteries having ether-based electrolytes

    Science.gov (United States)

    Amine, Khalil; Curtiss, Larry A.; Lu, Jun; Lau, Kah Chun; Zhang, Zhengcheng; Sun, Yang-Kook

    2016-10-25

    A lithium-air battery includes a cathode including a porous active carbon material, a separator, an anode including lithium, and an electrolyte including a lithium salt and polyalkylene glycol ether, where the porous active carbon material is free of a metal-based catalyst.

  7. Anode-supported single-chamber SOFCs based on gadolinia doped ceria electrolytes

    Directory of Open Access Journals (Sweden)

    Morales, M.

    2008-12-01

    Full Text Available The utilization of anode supported electrolytes is a useful strategy to increase the electrical properties of the solid oxide fuel cells, because it is possible to decrease considerably the thickness of the electrolytes. We have prepared successfully singlechamber fuel cells of gadolinia doped ceria electrolytes Ce1-xGdxO2-y (CGO supported on an anode formed by a cermet of Ni-CGO. Mixtures of precursor powders of NiO and gadolinium doped ceria with different particle sizes and compositions were analyzed to obtain optimal bulk porous anodes to be used as anode supported fuel cells. Doped ceria electrolytes were prepared by sol-gel related techniques. Then, ceria based electrolytes were deposited by dip coating at different thickness (15-30 µm using an ink prepared with nanometric powders of electrolytes dispersed in a commercial liquid polymer. Cathodes of La1-xSrxCoO3-s (LSCO were also prepared by sol-gel related techniques and were deposited by dip coating on the electrolyte thick films. Finally, electrical properties were determined in a single-chamber reactor where propane as fuel was mixed with synthetic air above the higher explosive limit. Stable density currents were obtained in these experimental conditions, but flow rates of the carrier gas and propane partial pressure were determinants for the optimization of the electrical properties of the fuel cells.

    La utilización de electrolitos soportados en el ánodo es una estrategia muy útil para mejorar las propiedades eléctricas de las pilas de combustible de óxido sólido, debido a que permiten disminuir considerablemente el espesor de los electrolitos. Para este trabajo, se han preparado exitosamente pilas de combustible de óxido sólido con electrolitos de ceria dopada con Gd, Ce1-xGdxO2-y (CGO soportados sobre un ánodo formado por un cermet de Ni/CGO. Dichas pilas se han

  8. Antimicrobial efficacy of alcohol-based hand gels.

    Science.gov (United States)

    Guilhermetti, M; Marques Wiirzler, L A; Castanheira Facio, B; da Silva Furlan, M; Campo Meschial, W; Bronharo Tognim, M C; Botelho Garcia, L; Luiz Cardoso, C

    2010-03-01

    In recent years, several commercial alcohol-based hand gels have appeared on the market to improve the hand-cleansing compliance of healthcare workers. Although the antimicrobial efficacy of these products has been reported in different countries, few studies have investigated this subject in Brazil. In this study, we assessed the antimicrobial efficacy of 12 alcohol-based hand gels produced in Brazil, containing 70% w/w or v/v ethyl alcohol as the active ingredient, according to the European Standard EN 1500 (EN 1500). The following alcohol gels were tested: Hand Gel, Voga Gel, Solumax Solugel, Doctor Clean, Rio Gel, Clear Gel, Sevengel, Hand CHC, Gel Bac, WBL-50 Gel, Sanigel and Soft Care Gel. In addition, 70% w/w ethyl alcohol and three alcohol-based hand rubs (Sterillium, Sterillium Gel, and Spitaderm), commonly used in Europe and effective according to EN 1500, were also tested. All the products tested, except for two, were approved by the EN 1500 test protocol with a 60s application. The results confirmed the antimicrobial efficacy of the majority of the alcohol gels produced in Brazil for hand hygiene of healthcare workers.

  9. Optimized Carbonate and Ester-Based Li-Ion Electrolytes

    Science.gov (United States)

    Smart, Marshall; Bugga, Ratnakumar

    2008-01-01

    To maintain high conductivity in low temperatures, electrolyte co-solvents have been designed to have a high dielectric constant, low viscosity, adequate coordination behavior, and appropriate liquid ranges and salt solubilities. Electrolytes that contain ester-based co-solvents in large proportion (greater than 50 percent) and ethylene carbonate (EC) in small proportion (less than 20 percent) improve low-temperature performance in MCMB carbon-LiNiCoO2 lithium-ion cells. These co-solvents have been demonstrated to enhance performance, especially at temperatures down to 70 C. Low-viscosity, ester-based co-solvents were incorporated into multi-component electrolytes of the following composition: 1.0 M LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + X (1:1:8 volume percent) [where X = methyl butyrate (MB), ethyl butyrate EB, methyl propionate (MP), or ethyl valerate (EV)]. These electrolyte formulations result in improved low-temperature performance of lithium-ion cells, with dramatic results at temperatures below 40 C.

  10. Hexagonal phase based gel-emulsion (O/H1 gel-emulsion): formation and rheology.

    Science.gov (United States)

    Alam, Mohammad Mydul; Aramaki, Kenji

    2008-11-04

    The formation, stability, and rheological behavior of a hexagonal phase based gel-emulsion (O/H1 gel-emulsion) have been studied in water/C12EO8/hydrocarbon oil systems. A partial phase behavior study indicates that the oil nature has no effect on the phase sequences in the ternary phase diagram of water/C12EO8/oil systems but the domain size of the phases or the oil solubilization capacity considerably changes with oil nature. Excess oil is in equilibrium with the hexagonal phase (H1) in the ternary phase diagram in the H1+O region. The O/H1 gel-emulsion was prepared (formation) and kept at 25 degrees C to check stability. It has been found that the formation and stability of the O/H1 gel-emulsion depends on the oil nature. After 2 min observation (formation), the results show that short chain linear hydrocarbon oils (heptane, octane) are more apt to form a O/H1 gel-emulsion compared to long chain linear hydrocarbon oils (tetradecane, hexadecane), though the stability is not good enough in either system, that is, oil separates within 24 h. Nevertheless, the formation and stability of the O/H1 gel-emulsion is appreciably increased in squalane and liquid paraffin. It is surmised that the high transition temperature of the H1+O phase and the presence of a bicontinuous cubic phase (V1) might hamper the formation of a gel-emulsion. It has been pointed out that the solubilization of oil in the H1 phase could be related to emulsion stability. On the other hand, the oil nature has little or no effect on the formation and stability of a cubic phase based gel-emulsion (O/I1 gel-emulsion). From rheological measurements, it has found that the rheogram of the O/H1 gel-emulsion indicates gel-type structure and shows shear thinning behavior similar to the case of the O/I1 gel-emulsion. Rheological data infer that the O/I1 gel-emulsion is more viscous than the O/H1 gel-emulsion at room temperature but the O/H1 gel-emulsion shows consistency at elevated temperature.

  11. Stabilizing the Performance of High-Capacity Sulfur Composite Electrodes by a New Gel Polymer Electrolyte Configuration.

    Science.gov (United States)

    Agostini, Marco; Lim, Du Hyun; Sadd, Matthew; Fasciani, Chiara; Navarra, Maria Assunta; Panero, Stefania; Brutti, Sergio; Matic, Aleksandar; Scrosati, Bruno

    2017-09-11

    Increased pollution and the resulting increase in global warming are drawing attention to boosting the use of renewable energy sources such as solar or wind. However, the production of energy from most renewable sources is intermittent and thus relies on the availability of electrical energy-storage systems with high capacity and at competitive cost. Lithium-sulfur batteries are among the most promising technologies in this respect due to a very high theoretical energy density (1675 mAh g(-1) ) and that the active material, sulfur, is abundant and inexpensive. However, a so far limited practical energy density, life time, and the scaleup of materials and production processes prevent their introduction into commercial applications. In this work, we report on a simple strategy to address these issues by using a new gel polymer electrolyte (GPE) that enables stable performance close to the theoretical capacity of a low cost sulfur-carbon composite with high loading of active material, that is, 70 % sulfur. We show that the GPE prevents sulfur dissolution and reduces migration of polysulfide species to the anode. This functional mechanism of the GPE membranes is revealed by investigating both its morphology and the Li-anode/GPE interface at various states of discharge/charge using Raman spectroscopy. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Voltage-Tunable Multicolor, Sub-1.5 V, Flexible Electrochromic Devices Based on Ion Gels.

    Science.gov (United States)

    Oh, Hwan; Seo, Dong Gyu; Yun, Tae Yong; Kim, Chan Young; Moon, Hong Chul

    2017-03-01

    Voltage-tunable multicolor electrochromic devices (ECDs) are fabricated based on flexible ion gels consisting of copolymers and ionic liquids as an electrolyte layer. Dimethyl ferrocene (dmFc) is incorporated into the gel, which serves as an anodic species. In this study, two electrochromic (EC) materials, monoheptyl viologen (MHV(+)) and diheptyl viologen (DHV(2+)), are employed and show significantly different EC behavior despite the similar chemical structure. Both MHV(+)- and DHV(2+)-containing ECDs are slightly yellowish in the bleached state, whereas the colored states are magenta and blue, respectively. All devices have good coloration efficiency of 87.5 cm(2)/C (magenta) and 91.3 cm(2)/C (blue). In addition, the required power of ∼248 μW/cm(2) (magenta) and ∼72 μW/cm(2) (blue) to maintain the colored state put the ion gel-based ECDs in a class of ultralow power consumption displays. On the basis of the distinct difference in the coloration voltage range between MHV(+) and DHV(2+), and the rubbery character of the gel, flexible ECDs showing multiple colors are demonstrated. These results imply that voltage-tunable multicolor ECDs based on the gel are attractive to functional electrochemical displays.

  13. Enhancement of thermal transport in Gel Polymer Electrolytes with embedded BN/Al2O3 nano- and micro-particles

    Science.gov (United States)

    Vishwakarma, Vivek; Jain, Ankur

    2017-09-01

    While Gel Polymer Electrolytes (GPEs) have been widely investigated for use in next-generation Li-ion cells due to the potential for improved thermal safety, thermal transport within a GPE is still poorly understood. Among all materials in a Li-ion cell, the GPE has the lowest thermal conductivity, and hence determines the overall rate of heat flow in a Li-ion cell. This makes it critical to measure and understand thermal transport in a GPE and investigate trade-offs between thermal and ionic transport. This paper presents measurements of thermal and ionic conductivities in a PVdF-based GPE. The effect of incorporating BN/Al2O3 ceramic nano/microparticles in the GPE on thermal and ionic transport is characterized. Measurements indicate up to 2.5X improvement in thermal conductivity of activated GPE membranes, with relatively minor effect on electrochemical performance of GPE-based single-layer cells. The measured enhancement in thermal conductivity is in very good agreement with theoretical calculations based on the effective medium theory that accounts for thermal transport in a dispersed, two-phase medium such as a GPE. The fundamental insights gained in this work on thermal transport in a GPE and the role of nano/microparticle inclusions may facilitate thermal-electrochemical optimization and design of GPEs for safe, high-performance Li-ion cells.

  14. All-solid-state electrochemical capacitors using MnO2 electrode/SiO2-Nafion electrolyte composite prepared by the sol-gel process

    Science.gov (United States)

    Shimamoto, Kazushi; Tadanaga, Kiyoharu; Tatsumisago, Masahiro

    2014-02-01

    Electrode-electrolyte composites of MnO2 active material, acetylene black (AB), and SiO2-Nafion solid electrolyte were prepared using the sol-gel process to form good solid-solid interfaces. The composites were obtained by the addition of MnO2 and AB into a sol of hydrolyzed tetraethoxysilane with Nafion, and successive solidification of the precursor sol. Scanning electron microscope and energy dispersive X-ray spectroscopy measurements show that good solid-solid interface is formed between electrodes and solid electrolytes in the composites. All-solid-state hybrid capacitors were fabricated using the composites or the hand-grinding mixture of MnO2, AB and SiO2-Nafion powder as positive electrodes, activated carbon powder as a negative electrode, and phosphosilicate gel as a solid electrolyte. The all-solid-state hybrid capacitors using the composites exhibit larger capacitances and better rate performance than the capacitors using the electrode prepared by hand-mixing of powders. Specific discharge capacitances of the capacitor with the composite are 85 F g-1 for the one with the composite electrode and 48 F g-1 for the one with the hand-mixed electrode, at 1 mA cm-2. Moreover, the all-solid-state capacitors using the composite electrode can be operated at temperatures between -30 °C and 60 °C.

  15. New Microporous Polymer Electrolyte Based on Polysiloxane Grafted with Imidazolium Iodide Moieties for DSSC

    Directory of Open Access Journals (Sweden)

    Yan Yang

    2011-01-01

    Full Text Available Two types of polysiloxane grafted with different ratio of imidazolium iodide moieties (IL-SiO2 have been synthesized to develop a micro-porous polymer electrolyte for quasi-solid-state dye-sensitized solar cells. The samples were characterized by 1HNMR, FT-IR spectrum, XRD, TEM and SEM, respectively. Moreover, the ionic conductivity of the electrolytes was measured by electrochemical workstation. Nanostructured polysiloxane containing imidazolium iodide showed excellent compatibility with organic solvent and polymer matrix for its ionic liquid characteristics. Increasing the proportion of imidazolium iodide moieties in polysiloxane improved the electrochemical behavior of the gel polymer electrolyte. A dye-sensitized solar cell with gel polymer electrolyte yielded an open-circuit voltage of 0.70 V, short-circuit current of 11.19 mA cm−2, and the conversion efficiency of 3.61% at 1 sun illumination.

  16. Neurologic complications of electrolyte disturbances and acid-base balance.

    Science.gov (United States)

    Espay, Alberto J

    2014-01-01

    Electrolyte and acid-base disturbances are common occurrences in daily clinical practice. Although these abnormalities can be readily ascertained from routine laboratory findings, only specific clinical correlates may attest as to their significance. Among a wide phenotypic spectrum, acute electrolyte and acid-base disturbances may affect the peripheral nervous system as arreflexic weakness (hypermagnesemia, hyperkalemia, and hypophosphatemia), the central nervous system as epileptic encephalopathies (hypomagnesemia, dysnatremias, and hypocalcemia), or both as a mixture of encephalopathy and weakness or paresthesias (hypocalcemia, alkalosis). Disabling complications may develop not only when these derangements are overlooked and left untreated (e.g., visual loss from intracranial hypertension in respiratory or metabolic acidosis; quadriplegia with respiratory insufficiency in hypermagnesemia) but also when they are inappropriately managed (e.g., central pontine myelinolisis when rapidly correcting hyponatremia; cardiac arrhythmias when aggressively correcting hypo- or hyperkalemia). Therefore prompt identification of the specific neurometabolic syndromes is critical to correct the causative electrolyte or acid-base disturbances and prevent permanent central or peripheral nervous system injury. This chapter reviews the pathophysiology, clinical investigations, clinical phenotypes, and current management strategies in disorders resulting from alterations in the plasma concentration of sodium, potassium, calcium, magnesium, and phosphorus as well as from acidemia and alkalemia.

  17. Capacitance Variation of Electrolyte-Gated Bilayer Graphene Based Transistors

    Directory of Open Access Journals (Sweden)

    Hediyeh Karimi

    2013-01-01

    Full Text Available Quantum capacitance of electrolyte-gated bilayer graphene field-effect transistors is investigated in this paper. Bilayer graphene has received huge attention due to the fact that an energy gap could be opened by chemical doping or by applying external perpendicular electric field. So, this extraordinary property can be exploited to use bilayer graphene as a channel in electrolyte-gated field-effect transistors. The quantum capacitance of bi-layer graphene with an equivalent circuit is presented, and also based on the analytical model a numerical solution is reported. We begin by modeling the DOS, followed by carrier concentration as a function V in degenerate and nondegenerate regimes. To further confirm this viewpoint, the presented analytical model is compared with experimental data, and acceptable agreement is reported.

  18. Understanding ternary poly(potassium benzimidazolide)-based polymer electrolytes

    DEFF Research Database (Denmark)

    Aili, David; Jankova Atanasova, Katja; Han, Junyoung;

    2016-01-01

    swelling, high electrolyte uptake, dramatic plasticization and increase of the ion conductivity for the formed poly(potassium benzimidazolide)-based structure. Further increasing the concentration of the bulk solution to 50 wt.% resulted in dehydration and extensive crystallization of the polymer matrix......Poly(2,20-(m-phenylene)-5,50-bisbenzimidazole) (m-PBI) can dissolve large amounts of aqueous electrolytes to give materials with extraordinary high ion conductivity and the practical applicability has been demonstrated repeatedly in fuel cells, water electrolysers and as anion conducting component...... in fuel cell catalyst layers. This work focuses on the chemistry of m-PBI in aqueous potassium hydroxide. Equilibration in aqueous KOH with concentrations of 15e20 wt.% was found to result in ionization of the polymer, causing released intermolecular hydrogen bonding. This allowed for extensive volume...

  19. Performance of Lithium Polymer Cells with Polyacrylonitrile based Electrolyte

    DEFF Research Database (Denmark)

    Perera, Kumudu; Skaarup, Steen; West, Keld

    2006-01-01

    had open circuit voltages in the range, 3.0 – 3.5 V vs Li. With increasing scan rates as well as thickness of the polymer electrode, diminishing of peaks and increase of peak separation in cyclic voltammograms was seen. Charge values obtained with constant charge discharge cycling and with cyclic......The performance of lithium polymer cells fabricated with Polyacrylonitrile (PAN) based electrolytes was studied using cycling voltammetry and continuous charge discharge cycling. The electrolytes consisted of PAN, ethylene carbonate (EC), propylene carbonate (PC) and lithium...... trifluoromethanesulfonate (LiCF3SO3 – LiTF). The polymer electrode material was polypyrrole (PPy) doped with dodecyl benzene sulfonate (DBS). The cells were of the form, Li / PAN : EC : PC : LiCF3SO3 / PPy : DBS. Polymer electrodes of three different thicknesses were studied using cycling at different scan rates. All cells...

  20. Characterization of Novel Castor Oil-Based Polyurethane Polymer Electrolytes

    Directory of Open Access Journals (Sweden)

    Salmiah Ibrahim

    2015-04-01

    Full Text Available Castor oil-based polyurethane as a renewable resource polymer has been synthesized for application as a host in polymer electrolyte for electrochemical devices. The polyurethane was added with LiI and NaI in different wt% to form a film of polymer electrolytes. The films were characterized by using attenuated total reflectance-Fourier transform infrared spectroscopy, dynamic mechanical analysis, electrochemical impedance spectroscopy, linear sweep voltammetry and transference number measurement. The highest conductivity of 1.42 × 10−6 S cm−1 was achieved with the addition of 30 wt% LiI and 4.28 × 10−7 S·cm−1 upon addition of 30 wt% NaI at room temperature. The temperature dependence conductivity plot indicated that both systems obeyed Arrhenius law. The activation energy for the PU-LiI and PU-NaI systems were 0.13 and 0.22 eV. Glass transition temperature of the synthesized polyurethane decreased from −15.8 °C to ~ −26 to −28 °C upon salts addition. These characterizations exhibited the castor oil-based polyurethane polymer electrolytes have potential to be used as alternative membrane for electrochemical devices.

  1. {sup 7}Li NMR spectroscopy and ion conduction mechanism of composite gel polymer electrolyte: A comparative study with variation of salt and plasticizer with filler

    Energy Technology Data Exchange (ETDEWEB)

    Saikia, D. [Department of Chemistry, Center for Nanotechnology and R and D Center for Membrane Technology, Chung Yuan Christian University, Chung Li 32023, Taiwan (China); Chen-Yang, Y.W. [Department of Chemistry, Center for Nanotechnology and R and D Center for Membrane Technology, Chung Yuan Christian University, Chung Li 32023, Taiwan (China)], E-mail: yuiwhei@cycu.edu.tw; Chen, Y.T.; Li, Y.K.; Lin, S.I. [Department of Chemistry, Center for Nanotechnology and R and D Center for Membrane Technology, Chung Yuan Christian University, Chung Li 32023, Taiwan (China)

    2009-01-30

    Microporous composite gel polymer electrolyte (CGPE) has been prepared by incorporating the home-made silica aerogel (SAG) particles into the poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) copolymer/LiClO{sub 4} matrix. The ionic transport behavior of the electrolyte is studied with various experimental techniques such as AC impedance, X-ray diffraction (XRD), infrared (IR) spectra, nuclear magnetic resonance (NMR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA), etc. The results reveal that the SAG particles are well dispersed in the electrolytes and incorporate with the other components of the CGPEs. The solid-state {sup 7}Li NMR study has confirmed the interactions of lithium ion with SAG, polymer and plasticizers, causing to form the microporous structure and reduce the glass transition temperature and crystallinity, resulting in an increase in ionic conductivity of the CGPE. The best ionic conductivity (1.04 x 10{sup -2} S/cm at room temperature) is obtained from the composite polymer electrolyte containing 4 wt% of SAG, which is approximately four times higher than the ionic conductivity of the electrolyte without the filler.

  2. Virus-Assembled Flexible Electrode-Electrolyte Interfaces for Enhanced Polymer-Based Battery Applications

    OpenAIRE

    Ayan Ghosh; Juchen Guo; Brown, Adam D.; Elizabeth Royston; Chunsheng Wang; Peter Kofinas; James N. Culver

    2012-01-01

    High-aspect-ratio cobalt-oxide-coated Tobacco mosaic virus (TMV-) assembled polytetrafluoroethylene (PTFE) nonstick surfaces were integrated with a solvent-free polymer electrolyte to create an anode-electrolyte interface for use in lithium-ion batteries. The virus-assembled PTFE surfaces consisted primarily of cobalt oxide and were readily intercalated with a low-molecular-weight poly (ethylene oxide) (PEO) based diblock copolymer electrolyte to produce a solid anode-electrolyte system. The ...

  3. Investigation of polymer electrolyte based on agar and ionic liquids

    Directory of Open Access Journals (Sweden)

    M. M. Silva

    2012-12-01

    Full Text Available The possibility to use natural polymer as ionic conducting matrix was investigated in this study. Samples of agarbased electrolytes with different ionic liquids were prepared and characterized by physical and chemical analyses. The ionic liquids used in this work were 1-ethyl-3-methylimidazolium ethylsulfate, [C2mim][C2SO4], 1-ethyl-3-methylimidazolium acetate, [C2mim][OAc] and trimethyl-ethanolammonium acetate, [Ch][OAc]. Samples of solvent-free electrolytes were prepared and characterized by ionic conductivity measurements, thermal analysis, electrochemical stability, X-ray diffraction, scanning electron microscopy and Fourier Transform infrared spectroscopy. Electrolyte samples are thermally stable up to approximately 190°C. All the materials synthesized are semicrystalline. The electrochemical stability domain of all samples is about 2.0 V versus Li/Li+. The preliminary studies carried out with electrochromic devices (ECDs incorporating optimized compositions have confirmed that these materials may perform as satisfactory multifunctional component layers in the field of ‘smart windows’, as well as ECD-based devices.

  4. Oil Gels Based on Styrene Butadiene Rubber

    Institute of Scientific and Technical Information of China (English)

    ZHOU Mei-hua (周美华); XU Jing-bo(徐静波); Won-jei CHO

    2004-01-01

    Four oil absorbents based on styrene butadiene (SBR),i. e., pure SBR (PS), 4- tert-butylstyrene-SBR (PBS),EPDM-SBR network (PES) and 4-tert-butylstyrene-EPDMSBR ( PBES ), were produced from crosslinking polymerization of uncured styrene butadiene rubber (SBR),4- tert-butylstyrene ( tBS ) and ethylene-propylene-diene terpolymer (EPDM). The reaction took place in toluene using benzoyl peroxide (BPO) as an initiator. Uncured SBR was used as both a pre-polymer and a crosslink agent in this work, and the crosslinked polymer was identified by IR spectroscopy. The oil absorbency of the crosslinked polymer was evaluated with the method ASTM (F726 - 81). The order of maximum oil absorbency was PBES > PBS >PES > PS. The maximum values of oil absorbency of PBES and PBS were 74.0g/g and 69.5g/g, respectively. Gel fractions and swelling kinetic constants, however, had the opposite sequences. The swelling kinetic constant of PS evaluated by an experimental equation was 49. 97 ×10-2h-1.

  5. The potential of incorporation of binary salts and ionic liquid in P(VP-co-VAc) gel polymer electrolyte in electrochemical and photovoltaic performances

    Science.gov (United States)

    Ming, Ng Hon; Ramesh, S.; Ramesh, K.

    2016-06-01

    In this study, dye-sensitized solar cells (DSSCs) has been assembled with poly(1-vinylpyrrolidone-co-vinyl acetate) (P(VP-co-VAc)) gel polymer electrolytes (GPEs) which have been incorporated with binary salt and an ionic liquid. The potential of this combination was studied and reported. The binary salt system GPEs was having ionic conductivity and power conversion efficiency (PCE) that could reach up to 1.90 × 10‑3 S cm‑1 and 5.53%, respectively. Interestingly, upon the addition of the ionic liquid, MPII into the binary salt system the ionic conductivity and PCE had risen steadily up to 4.09 × 10‑3 S cm‑1 and 5.94%, respectively. In order to know more about this phenomenon, the electrochemical impedance studies (EIS) of the GPE samples have been done and reported. Fourier transform infrared studies (FTIR) and thermogravimetric analysis (TGA) have also been studied to understand more on the structural and thermal properties of the GPEs. The Nyquist plot and Bodes plot studies have been done in order to understand the electrochemical properties of the GPE based DSSCs and Tafel polarization studies were done to determine the electrocatalytic activity of the GPE samples.

  6. An Electrically Driven and Readable Molecular Monolayer Switch Based on a Solid Electrolyte.

    Science.gov (United States)

    Marchante, Elena; Crivillers, Núria; Buhl, Moritz; Veciana, Jaume; Mas-Torrent, Marta

    2016-01-01

    The potential application of molecular switches as active elements in information storage has been demonstrated through numerous works. Importantly, such switching capabilities have also been reported for self-assembled monolayers (SAMs). SAMs of electroactive molecules have recently been exploited as electrochemical switches. Typically, the state of these switches could be read out through their optical and/or magnetic response. These output reading processes are difficult to integrate into devices, and furthermore, there is a need to use liquid environments for switching the redox-active molecular systems. In this work, both of these challenges were overcome by using an ionic gel as the electrolyte medium, which led to an unprecedented solid-state device based on a single molecular layer. Moreover, electrochemical impedance has been successfully exploited as the output of the system.

  7. Experimental data of inorganic gel based smart window using silica sol–gel process

    Directory of Open Access Journals (Sweden)

    Dayeon Jung

    2016-12-01

    Full Text Available In this article experimental data are presented for inorganic gel based smart window fabricated using silica sol–gel process. Parallel beam transmittances were measured as functions of voltages for samples fabricated with different concentrations of nitric acid. Spectroscopic transmittance data at different driving voltages for samples fabricated with different LC concentrations are shown. Transmittance spectra of the Si–Ti based gel-based-liquid-crystal (GDLC device measured as different driving voltages were compared with those of PDLC. GDLC showed much lower operating voltages, 10–15 V, for on-state. Formation of the LC droplet in gelation process is illustrated. The methyl organic group surrounds LC droplets. Demonstration of GDLC based smart window showed the successful operation with low driving voltages. GDLC window shows clear color, even at off-state, compared with PDLC.

  8. Favorable effects of titanium nitride or its thermally treated version in a gel electrolyte for a quasi-solid-state dye-sensitized solar cell

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chuan-Pei; Lin, Lu-Yin; Vittal, R. [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Ho, Kuo-Chuan [Department of Chemical Engineering, National Taiwan University, Taipei 10617 (China); Institute of Polymer Science and Engineering, National Taiwan University, Taipei 10617 (China)

    2011-02-01

    Titanium nitride (TiN) or its thermally treated version is incorporated into the gel electrolyte of a dye-sensitized solar cell (DSSC) and the consequent effects are investigated in terms of photovoltaic performance of the cell. The gel electrolyte is essentially prepared by using poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP). With an addition of 3 wt% TiN, the solar-to-electricity conversion efficiency ({eta}) of the DSSC reaches 5.33% from 4.15% of the cell without TiN. X-ray diffraction (XRD) spectra of thermally treated-TiN (tt-TiN) clearly shows the partial conversion of TiN into TiO{sub 2} with both anatase and rutile crystal phases. The DSSC with the incorporation of 3 wt% of tt-TiN into its electrolyte shows a further improved efficiency of 5.68%, with reference to the efficiency of TiN-incorporated DSSC. The cell with 3 wt% of tt-TiN also shows unfailing at-rest stability after more than 1000 h. Electrochemical impedance spectroscopy (EIS) is used to obtain charge transfer properties of the cells. Crystallinity and crystalline phases are analyzed by X-ray diffraction (XRD) spectra. Surface morphologies are observed with scanning electron microscopy (SEM). IPCE curves substantiate the variations in short circuit photocurrents. (author)

  9. Battery electrolytes. Citations from the NTIS data base

    Science.gov (United States)

    Young, C. G.

    1980-05-01

    Many types of solid, liquid and gaseous battery electrolytes are described and analyzed in the cited abstracts. Battery design, construction, and use, employing the listed electrolytes, are discussed. Battery design, construction, and use, employing the listed electrolytes, are discussed. Battery life, efficiency, and maintenance characteristics are also delineated. Included are 196 citations.

  10. A Model-Based Prognostics Methodology For Electrolytic Capacitors Based On Electrical Overstress Accelerated Aging

    Data.gov (United States)

    National Aeronautics and Space Administration — A remaining useful life prediction methodology for electrolytic capacitors is presented. This methodology is based on the Kalman filter framework and an empirical...

  11. A New Standard-Based Polynomial Interpolation (SBPIn) method to address gel-to-gel variability for the comparison of multiple denaturing gradient gel electrophoresis profile matrices.

    Science.gov (United States)

    Valentín-Vargas, Alexis; Chorover, Jon; Maier, Raina M

    2013-02-15

    The Standard-Based Polynomial Interpolation (SBPIn) method is a new simple three-step protocol proposed to address common gel-to-gel variations for the comparison of sample profiles across multiple DGGE gels. The advantages of this method include no requirement for additional software or modification of the standard DGGE protocol.

  12. A New Standard-Based Polynomial Interpolation (SBPIn) Method to Address Gel-to-Gel Variability for the Comparison of Multiple Denaturing Gradient Gel Electrophoresis Profile Matrices

    Science.gov (United States)

    Valentín-Vargas, Alexis; Chorover, Jon; Maier, Raina M.

    2013-01-01

    The Standard-Based Polynomial Interpolation (SBPIn) method is a new simple three-step protocol proposed to address common gel-to-gel variations for the comparison of sample profiles across multiple DGGE gels. The advantages of this method include no requirement for additional software or modification of the standard DGGE protocol. PMID:23234884

  13. Resistive switching memory based on bioinspired natural solid polymer electrolytes.

    Science.gov (United States)

    Raeis Hosseini, Niloufar; Lee, Jang-Sik

    2015-01-27

    A solution-processed, chitosan-based resistive-switching memory device is demonstrated with Pt/Ag-doped chitosan/Ag structure. The memory device shows reproducible and reliable bipolar resistive switching characteristics. A memory device based on natural organic material is a promising device toward the next generation of nonvolatile nanoelectronics. The memory device based on chitosan as a natural solid polymer electrolyte can be switched reproducibly between high and low resistance states. In addition, the data retention measurement confirmed the reliability of the chitosan-based nonvolatile memory device. The transparent Ag-embedded chitosan film showed an acceptable and comparable resistive switching behavior on the flexible plastic substrate as well. A cost-effective, environmentally benign memory device using chitosan satisfies the functional requirements of nonvolatile memory operations.

  14. Polybenzimidazoles based on high temperature polymer electrolyte fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Linares Leon, Jose Joaquin; Camargo, Ana Paula M.; Ashino, Natalia M.; Morgado, Daniella L.; Frollini, Elisabeth; Paganin, Valdecir A.; Gonzalez, Ernesto Rafael [Universidade de Sao Paulo (IQSC/USP), Sao Carlos, SP (Brazil); Bajo, Justo Lobato [University of Castilla-La Mancha, Ciudad Real (Spain). Dept. of Chemical Engineering

    2010-07-01

    This work presents an interesting approach in order to enhance the performance of Polymer Electrolyte Membrane Fuel Cells (PEMFC) by means of an increase in the operational temperature. For this, two polymeric materials, Poly(2,5-bibenzimidazole) (ABPBI) and Poly[2,2'-(m-phenyl en)-5,5' bib enzimidazol] (PBI), impregnated with phosphoric acid have been utilized. These have shown excellent properties, such as thermal stability above 500 deg C, reasonably high conductivity when impregnated with H{sub 3}PO{sub 4} and a low permeability to alcohols compared to Nafion. Preliminary fuel cells measurements on hydrogen based Polymer Electrolyte Membrane Fuel Cell (PEMFC) displayed an interestingly reasonable good fuel cell performance, a quite reduced loss when the hydrogen stream was polluted with carbon monoxide, and finally, when the system was tested with an ethanol/water (E/W) fuel, it displayed quite promising results that allows placing this system as an attractive option in order to increase the cell performance and deal with the typical limitations of low temperature Nafion-based PEMFC. (author)

  15. PREPARATION AND CHARACTERIZATION OF AMIDATED PECTIN BASED POLYMER ELECTROLYTE MEMBRANES

    Institute of Scientific and Technical Information of China (English)

    R.K.Mishra; A.Anis; S.Mondal; M.Dutt; A.K.Banthia

    2009-01-01

    The work presents the synthesis and characterization of ami dated pectin(AP)based polymer electrolyte membranes(PEM)crosslinked with glutaraldehyde(GA).The prepared membranes are characterized by Fourier transform infrared spectroscopy(FTIR),organic elemental analysis,X-ray diffraction studies(XRD),thermogravimetric analysis (TGA)and impedance spectroscopy.Mechanical properties of the membranes are evaluated by tensile tests.The degree of amidation(DA),molar and mass reaction yields(YM and YN)are calculated based on the results of organic elemental analysis.FTIR spectroscopy indicated the presence of primary and secondary amide absorption bands.XRD pattern of membranes clearly indicates that there is a considerable increase in crystallinity as compared to parent pectin.TGA studies indicate that AP is less thermally stable than reference pectin.A maximum room temperature conductivity of 1.098×10-3 Scm-1 is obtained in the membrane,which is designated as AP-3.These properties make them good candidates for low cost biopolymer electrolyte membranes for fuel cell applications.

  16. New polymer lithium secondary batteries based on ORMOCER (R) electrolytes-inorganic-organic polymers

    DEFF Research Database (Denmark)

    Popall, M.; Buestrich, R.; Semrau, G.

    2001-01-01

    Based on new plasticized inorganic-organic polymer electrolytes CM. Popall, M. Andrei, J. Kappel, J. Kron, K. Olma, B. Olsowski,'ORMOCERs as Inorganic-organic Electrolytes for New Solid State Lithium Batteries and Supercapacitors', Electrochim. Acta 43 (1998) 1155] new flexible foil-batteries...... electrolyte, typical for polymer electrolytes. Cycling tests (more than 900 cycles) proved that the unplasticized electrolyte can act as binder in composite cathodes of lithium secondary batteries [2]. Charge/discharge cycles of complete batteries like (Cu/active carbon/ORMOCER(R)/LiCoO2/Al) with an ORMOCER......(R) as separator electrolyte were measured. The voltage drop of these batteries is very similar to cells with standard liquid electrolytes and the efficiency is close to 100%. Cycling the batteries with a current density of 0.25 mA cm(-2) between the voltage limits of 3.1 and 4.1 V results in a charge...

  17. Multicolored, Low-Power, Flexible Electrochromic Devices Based on Ion Gels.

    Science.gov (United States)

    Moon, Hong Chul; Kim, Chang-Hyun; Lodge, Timothy P; Frisbie, C Daniel

    2016-03-09

    Ion gels composed of a copolymer and a room temperature ionic liquid are versatile solid-state electrolytes with excellent features including high ionic conductivity, nonvolatility, easily tunable mechanical properties, good flexibility and solution processability. Ion gels can be functionalized by incorporating redox-active species such as electrochemiluminescent (ECL) luminophores or electrochromic (EC) dyes. Here, we enhance the functionality of EC gels for realizing multicolored EC devices (ECDs), either by controlling the chemical equilibrium between a monomer and dimer of a colored EC species, or by modifying the molecular structures of the EC species. All devices in this work are conveniently fabricated by a "cut-and-stick" strategy, and require very low power for maintaining the colored state [i.e., 90 μW/cm(2) (113 μA/cm(2) at -0.8 V) for blue, 4 μW/cm(2) (10 μA/cm(2) at -0.4 V) for green, and 32 μW/cm(2) (79 μA/cm(2) at -0.4 V) for red ECD]. We also successfully demonstrate a patterned, multicolored, flexible ECD on plastic. Overall, these results suggest that gel-based ECDs have significant potential as low power displays in printed electronics powered by thin-film batteries.

  18. Ionic Liquid based polymer electrolytes for electrochemical sensors

    Directory of Open Access Journals (Sweden)

    Jakub Altšmíd

    2015-09-01

    Full Text Available Amperometric NO2 printed sensor with a new type of solid polymer electrolyte and a carbon working electrode has been developed. The electrolytes based on 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonylimide [EMIM][N(Tf2], 1-butyl-3-methylimidazolium trifluoromethanesulfonate [BMIM][CF3SO3] and 1-ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF4] ionic liquids were immobilized in poly(vinylidene fluoride matrix [PVDF]. The analyte, gaseous nitrogen dioxide, was detected by reduction at -500 mV vs. platinum pseudoreference electrode. The sensors showed a linear behavior in the whole tested range, i.e., 0 - 5 ppm and their sensitivities were in order of 0.3 x∙10-6 A/ppm. The sensor sensitivity was influenced by the electric conductivity of printing formulation; the higher the conductivity, the higher the sensor sensitivity. The rise/recovery times were in order of tens of seconds. The use of  screen printing technology and platinum pseudoreference electrode simplify the sensor fabrication and it does not have any negative effect on the sensor stability.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7371

  19. Physics Based Modeling and Prognostics of Electrolytic Capacitors

    Science.gov (United States)

    Kulkarni, Chetan; Ceyla, Jose R.; Biswas, Gautam; Goebel, Kai

    2012-01-01

    This paper proposes first principles based modeling and prognostics approach for electrolytic capacitors. Electrolytic capacitors have become critical components in electronics systems in aeronautics and other domains. Degradations and faults in DC-DC converter unit propagates to the GPS and navigation subsystems and affects the overall solution. Capacitors and MOSFETs are the two major components, which cause degradations and failures in DC-DC converters. This type of capacitors are known for its low reliability and frequent breakdown on critical systems like power supplies of avionics equipment and electrical drivers of electromechanical actuators of control surfaces. Some of the more prevalent fault effects, such as a ripple voltage surge at the power supply output can cause glitches in the GPS position and velocity output, and this, in turn, if not corrected will propagate and distort the navigation solution. In this work, we study the effects of accelerated aging due to thermal stress on different sets of capacitors under different conditions. Our focus is on deriving first principles degradation models for thermal stress conditions. Data collected from simultaneous experiments are used to validate the desired models. Our overall goal is to derive accurate models of capacitor degradation, and use them to predict performance changes in DC-DC converters.

  20. 提高凝胶电解质电导率的最新研究进展%The latest research progress on improving the conductivity of gel electrolyte

    Institute of Scientific and Technical Information of China (English)

    张有文; 李琪; 乔庆东

    2011-01-01

    The research improvement about a new kind of functional polymer material, gel electrolyte, in recent years was reviewed. The classification of the gel electrolytes was illustrated,including solid polymer electrolyte,gel polymer electrolyte, composite gel polymer electrolyte. The techniques to increase the conducting ratio of gel polymer electrolyte were stated emphatically. The methods mainly included, using the lithium salts which have high conductivity or high chemical stability, adopting cross-linking,copolymerization and blending methods to modify the molecular structure,reducing crystallization properties,adding plasticizing agent,adding mineral filler. The forecast and the development about the gel electrolyte were also prospect in the end.%综述了一种新型功能高分子材料——凝胶电解质近几年来的研究进展.说明了凝胶电解质的类型:固态聚合物电解质、凝胶聚合物电解质、复合凝胶聚合物电解质.重点阐述了提高凝胶电解质导电性能的方法.主要包括:采用电导率高和化学稳定性高的锂盐,采用交联、共聚和共混等方法对分子结构进行改性,降低结晶性能,添加增塑剂,添加无机填料等.并预测了凝胶电解质的发展前景.

  1. PEALD YSZ-based bilayer electrolyte for thin film-solid oxide fuel cells

    Science.gov (United States)

    Yu, Wonjong; Cho, Gu Young; Hong, Soonwook; Lee, Yeageun; Kim, Young Beom; An, Jihwan; Cha, Suk Won

    2016-10-01

    Yttria-stabilized zirconia (YSZ) thin film electrolyte deposited by plasma enhanced atomic layer deposition (PEALD) was investigated. PEALD YSZ-based bi-layered thin film electrolyte was employed for thin film solid oxide fuel cells on nanoporous anodic aluminum oxide substrates, whose electrochemical performance was compared to the cell with sputtered YSZ-based electrolyte. The cell with PEALD YSZ electrolyte showed higher open circuit voltage (OCV) of 1.0 V and peak power density of 182 mW cm-2 at 450 °C compared to the one with sputtered YSZ electrolyte(0.88 V(OCV), 70 mW cm-2(peak power density)). High OCV and high power density of the cell with PEALD YSZ-based electrolyte is due to the reduction in ohmic and activation losses as well as the gas and electrical current tightness.

  2. A novel polysulfide hydrogel electrolyte based on low molecular mass organogelator for quasi-solid-state quantum dot-sensitized solar cells

    Science.gov (United States)

    Huo, Zhipeng; Tao, Li; Wang, Shimao; Wei, Junfeng; Zhu, Jun; Dong, Weiwei; Liu, Feng; Chen, Shuanghong; Zhang, Bing; Dai, Songyuan

    2015-06-01

    A quasi-solid-state quantum dot-sensitized solar cell (QDSSC) is fabricated by using 12-hydroxystearic acid as a low molecular mass organogelator to gelate the polysulfide electrolyte. Noticeably, the gel to liquid transition temperature of this polysulfide hydrogel electrolyte is 96 °C, which contributes to the long-term stability of the quasi-solid-state QDSSC (QS-QDSSC). The influences of gelation on the charge transport, electron recombination and photovoltaic performance of the QS-QDSSC are investigated by electrochemical impedance spectroscopy. Moreover, the network of the hydrogel is investigated by the Field emission scanning electron microscopy and polarized optical light microscopy. It is found that the charge transport is influenced by the network in the hydrogel electrolyte, and the accelerated electron recombination at the photoanode/electrolyte interface leads to the decreased open-circuit voltage. The QS-QDSSC exhibits an energy conversion efficiency of 2.40% at AM 1.5 (100 mW cm-2) which is slightly lower than that of liquid electrolyte based cell (2.88%). However, the QS-QDSSC exhibits significantly improved stability during the accelerated thermal test. Especially, during the accelerated aging test, the short-circuit current density (Jsc) of the liquid electrolyte based QDSSC sharply decreased to nearly 35% of its initial value, while there is relatively less change in the Jsc for the QS-QDSSC.

  3. Luminescent polymer electrolytes based on chitosan and containing europium triflate

    Institute of Scientific and Technical Information of China (English)

    R Alves; ASS de Camargo; A Pawlicka; MM Silva

    2016-01-01

    Solid polymer electrolytes based on chitosan and europium triflate were prepared by solvent casting and characterized by X-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM), and photoluminescence spectroscopy. The X-ray diffraction exhibited that the samples were essentially amorphous with organized regions over the whole range of the salt content studied. The AFM analysis demonstrated that the smoother sample had roughness of 4.39 nm. Surface visualization through SEM revealed good homogeneity without any phase separation for more conductive samples and the less conductive showed some im-perfections on the surface. The emission and excitation spectra displayed the characteristic bands of Eu(CF3SO3)3 in addition to broad bands corresponding to the polymer host. The excited state5D0 lifetime values ranged from 0.29–0.37 ms for the studied samples.

  4. High performance silicon nanoparticle anode in fluoroethylene carbonate-based electrolyte for Li-ion batteries.

    Science.gov (United States)

    Lin, Yong-Mao; Klavetter, Kyle C; Abel, Paul R; Davy, Nicholas C; Snider, Jonathan L; Heller, Adam; Mullins, C Buddie

    2012-07-25

    Electrodes composed of silicon nanoparticles (SiNP) were prepared by slurry casting and then electrochemically tested in a fluoroethylene carbonate (FEC)-based electrolyte. The capacity retention after cycling was significantly improved compared to electrodes cycled in a traditional ethylene carbonate (EC)-based electrolyte.

  5. [Microchips based on three dimensional gel cells: history and perspective].

    Science.gov (United States)

    Kolchinskiĭ, A M; Griadunov, D A; Lysov, Iu P; Mikhaĭlovich, V M; Nasedkina, T V; Turygin, A Iu; Rubina, A Iu; Barskiĭ, V E; Zasedatelev, A S

    2004-01-01

    The review describes the history of creation and development of the microchip technology and its role in the human genome project in Russia. The emphasis is placed on the three-dimensional gel-based microchips developed at the Center of Biological Microchips headed by A.D. Mirzabekov since 1988. The gel-based chips of the last generation, IMAGE chips (Immobilized Micro Array of Gel Elements), have a number of advantages over the previous versions. The microchips are manufactured by photo-initiated copolymerization of gel components and immobilized molecules (DNA, proteins, and ligands). This ensures an even distribution of the immobilized probe throughout the microchip gel element with a high yield (about 50% for oligonucleotides). The use of methacrylamide as a main component of the polymerization mixture resulted in a substantial increase of gel porosity without affecting its mechanical strength and stability, which allowed one to work with the DNA fragments of up to 500 nt in length, as well as with rather large protein molecules. At present, the gel-based microchips are widely applied to address different problems. The generic microchips containing a complete set of possible hexanucleotides are used to reveal the DNA motifs binding with different proteins and to study the DNA-protein interactions. The oligonucleotide microchips are a cheap and reliable tool of diagnostics designed for mass application. Biochips have been developed for identification of the tuberculosis pathogen and its antibiotic-resistant forms; for diagnostics of orthopoxviruses, including the smallpox virus; for diagnostics of the anthrax pathogen; and for identification of chromosomal rearrangements in leukemia patients. The protein microchips can be adapted for further use in proteomics. Bacterial and yeast cells were also immobilized in the gel, maintaining their viability, which open a wide potential for creation biosensors on the basis of microchips.

  6. Towards safer sodium-ion batteries via organic solvent/ionic liquid based hybrid electrolytes

    Science.gov (United States)

    Monti, Damien; Ponrouch, Alexandre; Palacín, M. Rosa; Johansson, Patrik

    2016-08-01

    Hybrid electrolytes aimed at application in sodium-ion batteries (SIB) consisting of an organic solvent mixture (EC:PC) and different ionic liquids (ILs); EMImTFSI, BMImTFSI, and Pyr13TFSI, and with the NaTFSI salt providing the Na+ charge carriers have here been extensively studied. The physico-chemical and electrochemical characterisation includes ionic conductivity, viscosity, density, cation coordination and solvation, various safety measures, and electrochemical stability window (ESW). Hybrid electrolytes with 10-50% of IL content were found to have ionic conductivities on par with comparable organic solvent based electrolytes, but with highly enhanced safety properties. A systematic Raman spectroscopy study of the cation coordination and solvation before and after electrolyte safety tests by ignition suggest that IL cations and TFSI remain stable when ignited while organic solvents are consumed. Finally, the solid electrolyte interphase (SEI) formed when using hybrid electrolytes has both better mechanical and electrochemical stability than the SEI derived from pure IL based electrolytes. For a half-cell with a hard carbon (HC) electrode and a hybrid electrolyte with a composition of 0.8 m NaTFSI in EC0.45:PC0.45:Pyr13TFSI0.10 encouraging results were obtained for IL based electrolytes - ca. 182 mAhg-1 at C/10 over 40 cycles.

  7. Development of ionic gels using thiol-based monomers in ionic liquid

    Science.gov (United States)

    Ahmed, Kumkum; Naga, Naofumi; Kawakami, Masaru; Furukawa, Hidemitsu

    2016-04-01

    Ionic gels (IGs) using ionic liquids (ILs) can propose diverse applications in the field of optics, sensors and separation have opened wide prospects in materials science. ILs have attracted remarkable interest for gel polymer electrolytes and batteries based on their useful properties such as non-volatility, non-flammability, a wide electrochemical window, high thermal stability and a high ionic conductivity. The formation of gel in IL media makes it possible to immobilize ILs within organic or inorganic matrices and to take advantage of their unique properties in the solid state, thus eliminating some shortcomings related to shaping and risk of leakage. In this work for the first time we used multifunctional thiol monomers having uniform structure and good compatibility with the IL of our interest. Therefore we focused on developing thiol monomer-based IGs using multifunctional thiol monomers and acrylate crosslinkers utilizing thiol-ene reaction between monomer and crosslinking molecules in an IL medium and characterize their physico-chemical properties like thermal, conductive, mechanical properties etc.. This work has been focused mainly to improve the mechanical strength of IGs and make prospects of IGs in tribology and lubricants.

  8. Suppression of Aluminum Corrosion in Lithium Bis(trifluoromethanesulfonyl)imide-based Electrolytes by the Addition of Fumed Silica

    Energy Technology Data Exchange (ETDEWEB)

    Louis, Hamenu; Ko, Jangmyoun [Hanbat National Univ., Daejeon (Korea, Republic of); Lee, Younggi; Kim, Kwangman [Electronics and Telecommunications Research Institute, Daejeon (Korea, Republic of); Cho, Wonil [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

    2013-06-15

    The corrosion property of aluminum by lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt is investigated in liquid and gel electrolytes consisting of ethylene carbonate/propylene carbonate/ethylmethyl carbonate/diethyl carbonate (20:5:55:20, vol %) with vinylene carbonate (2 wt %) and fluoroethylene carbonate (5 wt %) using conductivity measurement, cyclic voltammetry, scanning electron microscopy, and energy dispersive X-ray spectroscopy. All corrosion behaviors are attenuated remarkably by using three gel electrolytes containing 3 wt % of hydrophilic and hydrophobic fumed silica. The addition of silica particles contributes to the increase in the ionic conductivity of the electrolyte, indicating temporarily formed physical crosslinking among the silica particles to produce a gel state. Cyclic voltammetry also gives lower anodic current responses at higher potentials for repeating cycles, confirming further corrosion attenuation or electrochemical stability. In addition, the degree of corrosion attenuation can be affected mainly by the electrolytic constituents, not by the hydrophilicity or hydrophobicity of silica particles.

  9. PVDF-HFP-based porous polymer electrolyte membranes for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Miao, Ruiying; Liu, Bowen; Zhu, Zhongzheng; Liu, Yun; Li, Jianling; Wang, Xindong [Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Li, Qingfeng [Department of Chemistry, Technology University of Denmark, DK-2800 Lyngby (Denmark)

    2008-10-01

    As a potential electrolyte for lithium-ion batteries, a porous polymer electrolyte membrane based on poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) was prepared by a phase inversion method. The casting solution, effects of the solvent and non-solvent and addition of micron scale TiO{sub 2} particles were investigated. The membranes were characterized by SEM, XRD, AC impedance, and charge/discharge tests. By using acetone as the solvent and water as the non-solvent, the prepared membranes showed good ability to absorb and retain the lithium ion containing electrolyte. Addition of micron TiO{sub 2} particles to the polymer electrolyte was found to enhance the tensile strength, electrolyte uptake, ion conductivity and the electrolyte/electrode interfacial stability of the membrane. (author)

  10. Gassing behavior of lithium titanate based lithium ion batteries with different types of electrolytes

    Science.gov (United States)

    Liu, Jiali; Bian, Peiwen; Li, Jia; Ji, Wenjiao; Hao, Hao; Yu, Aishui

    2015-07-01

    Gassing behavior of LiMn2O4/Li4Ti5O12 full cell with different electrolytes that stored at elevated temperature of 70 °C is investigated. Scanning electron microscope (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) are used to study the solid electrolyte interphase (SEI) layer formed in battery formation and storage processes. The results suggest that the SEI film is formed as a consequence of intrinsic reaction between Li4Ti5O12 electrode and electrolyte solvents. A smooth SEI layer is formed on Li4Ti5O12 electrode with full coverage in propylene carbonate (PC) based electrolyte during lithium intercalation process while gradually dissolved with lithium extraction. Moreover, the gas specificities generated in the different electrolyte solvents are also determined by gas chromatography-mass spectrometer (GC-MS) analysis and the reaction mechanisms of LTO electrode with electrolyte solvents are proposed.

  11. Synthesis and characterization of polyethylene oxide based nano composite electrolyte

    Indian Academy of Sciences (India)

    M Malathi; K Tamilarasan

    2014-08-01

    Polyethylene oxide (PEO) – montmorillonite (MMT) composite electrolytes were synthesised by solution casting technique. The salt used for the study is Lithium perchlorate (LiClO4). The morphology and percentage of crystallinity data were obtained through X-ray Diffraction and Differential Scanning Caloriemetry. The ionic conductivity of the polymer electrolytes was studied by impedance spectroscopy. The addition of MMT resulted in an increase in conductivity over the temperature range of 25–60°C. The ionic conductivity of a composite polymer electrolyte containing 1.2 wt% MMT was 1 × 10-5 S cm−1 at 25°C, which is at least one order of magnitude higher than that of the polymer electrolyte (4 × 10-7S cm−1). The increase in ionic conductivity is explained on the basis of crystallinity of the polymer electrolyte.

  12. Formation and properties of gels based on lipo-plexes.

    Science.gov (United States)

    Pucci, Carlotta; Tardani, Franco; La Mesa, Camillo

    2014-06-12

    Aqueous systems containing sodium taurodeoxycholate and, eventually, soybean lecithin were investigated. Depending on the relative amounts of two such species, molecular, micellar, vesicular, liquid crystalline, and solid phases were formed. In the presence of bovine serum albumin, micellar and vesicular systems form lipo-plexes. The latter self-organize into gels, depending on composition and thermal treatments. According to scanning electron microscopy, vesicle-based gels obtained from lipo-plexes form sponge-like entities, whereas micelle-based ones self-arrange in fibrous organizations. Gels are characterized by a significant viscoelasticity in a wide temperature and frequency range. Rheological data were interpreted by assuming strict relations between the system response and the self-organization of the lipo-plexes into gels. It was inferred that differences in the gel properties depend on the different self-assembly modes of the aggregates formed by the mentioned lipo-plexes. Use of the above systems in biomedical applications, mostly in the preparation of matrices requiring the use of smart and biocompatible gels, is suggested.

  13. Lithium-ion-based solid electrolyte tuning of the carrier density in graphene

    Science.gov (United States)

    Zhao, Jialin; Wang, Meng; Li, Hui; Zhang, Xuefu; You, Lixing; Qiao, Shan; Gao, Bo; Xie, Xiaoming; Jiang, Mianheng

    2016-10-01

    We have developed a technique to tune the carrier density in graphene using a lithium-ion-based solid electrolyte. We demonstrate that the solid electrolyte can be used as both a substrate to support graphene and a back gate. It can induce a change in the carrier density as large as 1 × 1014 cm‑2, which is much larger than that induced with oxide-film dielectrics, and it is comparable with that induced by liquid electrolytes. Gate modulation of the carrier density is still visible at 150 K, which is lower than the glass transition temperature of most liquid gating electrolytes.

  14. Lithium-ion-based solid electrolyte tuning of the carrier density in graphene

    Science.gov (United States)

    Zhao, Jialin; Wang, Meng; Li, Hui; Zhang, Xuefu; You, Lixing; Qiao, Shan; Gao, Bo; Xie, Xiaoming; Jiang, Mianheng

    2016-01-01

    We have developed a technique to tune the carrier density in graphene using a lithium-ion-based solid electrolyte. We demonstrate that the solid electrolyte can be used as both a substrate to support graphene and a back gate. It can induce a change in the carrier density as large as 1 × 1014 cm−2, which is much larger than that induced with oxide-film dielectrics, and it is comparable with that induced by liquid electrolytes. Gate modulation of the carrier density is still visible at 150 K, which is lower than the glass transition temperature of most liquid gating electrolytes. PMID:27698413

  15. Improved Composite Gel Electrolyte by Layered Vermiculite for Quasi-Solid-State Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    Hongcai He

    2014-01-01

    Full Text Available A composite quasisolid electrolyte is prepared by adding a layered vermiculite (VMT into the iodide/triiodide electrolyte including 4-tert-butylpyridine, which obviously improves the photovoltaic properties of quasisolid dye-sensitized solar cells (DSSCs. When adding 6 wt% VMT, the maximum photovoltaic conversion efficiency of 3.89% is obtained, which reaches more than two times greater than that without VMT. This enhancement effect is primarily explained by studying the Nyquist spectra, dark currents, and photovoltaic conversion efficiency.

  16. Enhanced performance of a quasi-solid-state dye-sensitized solar cell with aluminum nitride in its gel polymer electrolyte

    KAUST Repository

    Huang, Kuan-Chieh

    2011-08-01

    The effects of incorporation of aluminum nitride (AlN) in the gel polymer electrolyte (GPE) of a quasi-solid-state dye-sensitized solar cell (DSSC) were studied in terms of performance of the cell. The electrolyte, consisting of lithium iodide (LiI), iodine (I2), and 4-tert-butylpyridine (TBP) in 3-methoxypropionitrile (MPN), was solidified with poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP). The 0.05, 0.1, 0.3, and 0.5 wt% of AlN were added to the electrolyte for this study. XRD analysis showed a reduction of crystallinity in the polymer PVDF-HFP for all the additions of AlN. The DSSC fabricated with a GPE containing 0.1 wt% AlN showed a short-circuit current density (JSC) and power-conversion efficiency (η) of 12.92±0.54 mA/cm2 and 5.27±0.23%, respectively, at 100 mW/cm2 illumination, in contrast to the corresponding values of 11.52±0.21 mA/cm2 and 4.75±0.08% for a cell without AlN. The increases both in JSC and in η of the promoted DSSC are attributed to the higher apparent diffusion coefficient of I- in its electrolyte (3.52×10-6 cm2/s), compared to that in the electrolyte without AlN of a DSSC (2.97×10-6 cm 2/s). At-rest stability of the quasi-solid-state DSSC with 0.1 wt% of AlN was found to decrease hardly by 5% and 7% at room temperature and at 40 °C, respectively, after 1000 h duration. The DSSC with a liquid electrolyte showed a decrease of about 40% at room temperature, while it virtually lost its performance in about 150 h at 40 °C. Explanations are further substantiated by means of electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and by porosity measurements. © 2010 Elsevier B.V.

  17. Sol-gel-based biosensing applied to medicinal science.

    Science.gov (United States)

    Moreira, Felismina T C; Moreira-Tavares, Ana P; Sales, M Goreti F

    2015-01-01

    Biosensors have opened new horizons in biomedical analysis, by ensuring increased assay speed and flexibility, and allowing point-of-care applications, multi-target analyses, automation and reduced costs of testing. This has been a result of many studies merging nanotechnology with biochemistry over the years, thereby enabling the creation of more suitable environments to biological receptors and their substitution by synthetic analogue materials. Sol-gel chemistry, among other materials, is deeply involved in this process. Sol-gel processing allows the immobilization of organic molecules, biomacromolecules and cells maintaining their properties and activities, permitting their integration into different transduction devices, of electrochemical or optical nature, for single or multiple analyses. Sol-gel also allows to the production of synthetic materials mimicking the activity of natural receptors, while bringing advantages, mostly in terms of cost and stability. Moreover, the biocompatibility of sol-gel materials structures of biological nature allowed the use of these materials in emerging in vivo applications. In this chapter, biosensors for biomedical applications based on sol-gel derived composites are presented, compared and described, along with current emerging applications in vivo, concerning drug delivery or biomaterials. Sol-gel materials are shown as a promising tool for current, emerging and future medical applications.

  18. PVDF-HFP-based porous polymer electrolyte membranes for lithium-ion batteries

    DEFF Research Database (Denmark)

    Miao, Ruiying; Liu, Bowen; Zhu, Zhongzheng

    2008-01-01

    As a potential electrolyte for lithium-ion batteries, a porous polymer electrolyte membrane based on poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) was prepared by a phase inversion method. The casting solution, effects of the solvent and non-solvent and addition of micron scale TiO2 par...

  19. Lithium bis(fluorosulfonyl)imide based low ethylene carbonate content electrolyte with unusual solvation state

    Science.gov (United States)

    Uchida, Satoshi; Ishikawa, Masashi

    2017-08-01

    We prepared a lithium bis(fluorosulfonyl)imide (LiFSI)-based low ethylene carbonate (EC) content electrolyte as a new electrolyte. LiFSI enough dissociates in mixed solvents containing only a small amount of EC and the LiFSI-based low EC content electrolyte shows a high ionic conductivity comparable to that of a conventional LiPF6-based high EC content electrolyte. In addition, the LiFSI-based low EC content electrolyte has an unusual solvation state of Li ion and we consider that the desolvation process from Li ion in our new electrolyte system is different from that in the conventional high EC content systems. A graphite half-cell assembled with our new electrolyte shows a quite low Li ion transfer resistance and outstanding charge and discharge rate performance compared to the conventional high EC content systems. A graphite/LiNi1/3Mn1/3Co1/3O2 cell assembled with our new electrolyte also shows superior charge and discharge rate performance and excellent long cycle stability.

  20. Virus-Assembled Flexible Electrode-Electrolyte Interfaces for Enhanced Polymer-Based Battery Applications

    Directory of Open Access Journals (Sweden)

    Ayan Ghosh

    2012-01-01

    Full Text Available High-aspect-ratio cobalt-oxide-coated Tobacco mosaic virus (TMV- assembled polytetrafluoroethylene (PTFE nonstick surfaces were integrated with a solvent-free polymer electrolyte to create an anode-electrolyte interface for use in lithium-ion batteries. The virus-assembled PTFE surfaces consisted primarily of cobalt oxide and were readily intercalated with a low-molecular-weight poly (ethylene oxide (PEO based diblock copolymer electrolyte to produce a solid anode-electrolyte system. The resulting polymer-coated virus-based system was then peeled from the PTFE backing to produce a flexible electrode-electrolyte component. Electrochemical studies indicated the virus-structured metal-oxide PEO-based interface was stable and displayed robust charge transfer kinetics. Combined, these studies demonstrate the development of a novel solid-state electrode architecture with a unique peelable and flexible processing attribute.

  1. Development and characterization of poly(1-vinylpyrrolidone-co-vinyl acetate) copolymer based polymer electrolytes.

    Science.gov (United States)

    Sa'adun, Nurul Nadiah; Subramaniam, Ramesh; Kasi, Ramesh

    2014-01-01

    Gel polymer electrolytes (GPEs) are developed using poly(1-vinylpyrrolidone-co-vinyl acetate) [P(VP-co-VAc)] as the host polymer, lithium bis(trifluoromethane) sulfonimide [LiTFSI] as the lithium salt and ionic liquid, and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide [EMImTFSI] by using solution casting technique. The effect of ionic liquid on ionic conductivity is studied and the optimum ionic conductivity at room temperature is found to be 2.14 × 10(-6) S cm(-1) for sample containing 25 wt% of EMImTFSI. The temperature dependence of ionic conductivity from 303 K to 353 K exhibits Arrhenius plot behaviour. The thermal stability of the polymer electrolyte system is studied by using thermogravimetric analysis (TGA) while the structural and morphological properties of the polymer electrolyte is studied by using Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction analysis (XRD), respectively.

  2. Gel Polymer Electrolytes for Lithium Ion Batteries%锂离子电池用凝胶聚合物电解质研究进展

    Institute of Scientific and Technical Information of China (English)

    关红艳; 连芳; 仇卫华; 孙加林

    2012-01-01

    凝胶聚合物电解质既具有固态聚合物电解质良好的力学加工性能和安全性能,又具有传统液态电解质较高的室温离子电导率。但凝胶聚合物电解质由于室温离子电导率低、力学强度较差的缺点限制了其在锂离子电池上的应用。结合目前研究的最新进展,文中针对几种常用凝胶聚合物电解质体系聚氧化乙烯、聚丙烯腈、聚甲基丙烯酸甲酯、聚偏氟乙烯-六氟丙烯和聚乙烯醇缩醛进行了综述,对其制备方法以及通过聚合物调控、加入无机填料和复合离子液体进行改性处理做了较全面的介绍,并探讨了凝胶聚合物电解质的应用前景。%Gel polymer electrolytes (GPEs) possess both good processibility and safety performance of solid polymer electrolyte and a high conductivity of liquid electrolyte. However, the low conductivity at room temperature and poor mechanical strength restrict their applications in lithium-ion batteries. In this paper, the up-to-date research progress of some attractive gel polymer electrolytes have been reviewed, including poly(ethylene oxide) (PEO), poly (acrylonitrile) (PAN), poly ( methyl methacrylate) (PMMA), poly ( vinylidene fluoride-hexafluoro propylene) (PVdF-HFP) and poly(vinyl acetal) s (PVAc). Additionally, their preparation methods have been summarized. And the improvements of their properties are focused on, by modifying polymer structure, reinforcing with inorganic fillers and blending with ionic liquids. Finally, the prospects of their application in lithium-ion batteries are also discussed here.

  3. Capacitance Variation of Electrolyte-Gated Bilayer Graphene Based Transistors

    OpenAIRE

    Hediyeh Karimi; Rubiyah Yusof; Mohammad Taghi Ahmadi; Mehdi Saeidmanesh; Meisam Rahmani; Elnaz Akbari; Wong King Kiat

    2013-01-01

    Quantum capacitance of electrolyte-gated bilayer graphene field-effect transistors is investigated in this paper. Bilayer graphene has received huge attention due to the fact that an energy gap could be opened by chemical doping or by applying external perpendicular electric field. So, this extraordinary property can be exploited to use bilayer graphene as a channel in electrolyte-gated field-effect transistors. The quantum capacitance of bi-layer graphene with an equivalent circuit is presen...

  4. 新型多孔凝胶电解质的制备及其在准固态柔性基染料敏化太阳电池中的应用%Application of the Novel Porous Gel Electrolyte in Flexible Quasi-Solid-State Dye-Sensitized Solar Cell

    Institute of Scientific and Technical Information of China (English)

    李清华; 王应民; 李文杰; 张婷婷; 蔡莉; 程泽秀; 李禾

    2012-01-01

    A novel gel polymer electrolyte based on poly(acrylic acid-g-CTAB)-polypyrrole is prepared. Based on the gel electrolyte, a flexible quasi-solid-stale dye-sensitized solar cell (DSSC) is fabricated hy using a low-temperature filming technique. The researches by scanning electron microscopy, thermal degradation analysis and cyclic voltammetry show the effect of the gel polymer electrolyte on flexible DSSC. Owing to high conductivity and the catalytic function of polypyrrole for I -/I3- redox reaction for the gel electrolyte, the flexible quasi-solidstatedye-sensitized solar cell shows a light-to-electric energy conversion efficiency of 1. 28%, under simulated solar light irradiation with intensity of 100 mW/cm2[air mass (AM) 1.5].%制备了一种新型多孔聚丙烯酸/十六烷基三甲基溴化铵-聚吡咯凝胶电解质,并将其应用于柔性基染料敏化太阳电池(DSSC).通过扫描电镜表征、热重分析测试、电化学性能测试和柔性电池光电性能测试等手段,分析了凝胶电解质对柔性基DSSC的光电性能影响.研究结果表明:随着聚吡咯的引入,提高凝胶电解质导电性以及催化电解质中的Ⅰ- /Ⅰ3-离子电对等性能,最终在100 mW/cm2[大气质量(AM)1.5]光照条件下,测得基于该准固态凝胶电解质的柔性基DSSC光电转换效率达1.28%.

  5. Electrochemical Performance of LiNi0.5Mn1.5O4 by Sol-gel Self-combustion Reaction Method in Different Kinds of Electrolyte for High-voltage Rechargeable Lithium Cells

    Science.gov (United States)

    Liang, Xinghua; Shi, Lin; Liu, Yusi; Zeng, Shuaibo; Ye, Chaochao

    2015-07-01

    LiNi0.5Mn1.5O4 cathode material was synthesized through sol-gel self-combustion reaction method. LiNi0.5Mn1.5O4 powders were subsequently characterized as cathode materials in a Li-ion coin cell comprising a Li anode with electrolyte A or electrolyte B. 1.0 mol/L Lithium Hexafluorophosphate (LiPF6) dissolved in volume ration of ethylene carbonate (EC) to ethyl methyl carbonate (EMC) to diethyl carbonate (DEC) corresponded to 4:3:3as electrolyte A, 1.0 mol/L LiPF6 dissolved in volume ration of EC to EMC to DEC corresponded to 4:2:4 as electrolyte B. Electrochemical performance of lithium cells was evaluated. These tests showed that no matter the cells with electrolyte A or electrolyte B has good discharge platform in 4.7V range (3.5V-4.75V) at the rate of 0.1C, the initial discharge capacity of cell with electrolyte B was higher than that with electrolyte A.

  6. Comparative gel-based phosphoproteomics in response to signaling molecules

    KAUST Repository

    Marondedze, Claudius

    2013-09-03

    The gel-based proteomics approach is a valuable technique for studying the characteristics of proteins. This technique has diverse applications ranging from analysis of a single protein to the study of the total cellular proteins. Further, protein quality and to some extent distribution can be first assessed by means of one-dimensional gel electrophoresis and then more informatively, for comparative analysis, using the two-dimensional gel electrophoresis technique. Here, we describe how to take advantage of the availability of fluorescent dyes to stain for a selective class of proteins on the same gel for the detection of both phospho- and total proteomes. This enables the co-detection of phosphoproteins as well as total proteins from the same gel and is accomplished by utilizing two different fluorescent stains, the ProQ-Diamond, which stains only phosphorylated proteins, and Sypro Ruby, which stains the entire subset of proteins. This workflow can be applied to gain insights into the regulatory mechanisms induced by signaling molecules such as cyclic nucleotides through the quantification and subsequent identification of responsive phospho- and total proteins. © Springer Science+Business Media New York 2013.

  7. Polymer electrolytes based on aromatic lithium sulfonyl-imide compounds; Electrolytes polymeres a base de sulfonylimidures de lithium aromatiques

    Energy Technology Data Exchange (ETDEWEB)

    Reibel, L.; Bayoudh, S. [Centre National de la Recherche Scientifique (CNRS), 67 - Strasbourg (France). Institut Charles Sadron; Baudry, P. [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches; Majastre, H. [Bollore Technologies, 29 - Quimper (France); Herlem, G. [UFR de Sciences et Techniques, L.E.S., 25 - Besancon (France)

    1996-12-31

    This paper presents ionic conductivity results obtained with polymer electrolytes and also with propylene carbonate solutions. The domain of electrochemical activity of this salt has been determined using cycle volt-amperometry in propylene carbonate. Preliminary experiments on the stability of the polymer electrolyte with respect to the lithium electrode have been carried out for a possible subsequent use in lithium batteries. (J.S.) 4 refs.

  8. Copper base materials prepared by gel-casting process

    Institute of Scientific and Technical Information of China (English)

    LIU Weihua; JIA Chengchang; SHI Yantao; HAN Yuepeng

    2008-01-01

    Gel-casting process was developed as a new molding process in the field of copper base powder metallurgy to manufacture metal parts with excellent performance and complex shapes.Through changing the parameters of gel-casting process,such as dispersant and solid loading,the corresponding effects on the rheology of Cu slurries,molding and sintering behaviors were studied.The results show that the viscosity of Cu slurries was significantly reduced with an increase in dispersant.The most appropriate solid loading was found to be 61% and the sintering temperature was 910℃ in these experiments.After the optimization of parameters of gel-casting process,copper composite parts with relatively high density and better properties were obtained.

  9. Toward highly stable solid-state unconventional thin-film battery-supercapacitor hybrid devices: Interfacing vertical core-shell array electrodes with a gel polymer electrolyte

    Science.gov (United States)

    Pandey, Gaind P.; Klankowski, Steven A.; Liu, Tao; Wu, Judy; Li, Jun

    2017-02-01

    A novel solid-state battery-supercapacitor hybrid device is fabricated for high-performance electrical energy storage using a Si anode and a TiO2 cathode in conjunction with a flexible, solid-like gel polymer electrolyte film as the electrolyte and separator. The electrodes were fabricated as three-dimensional nanostructured vertical arrays by sputtering active materials as conformal shells on vertically aligned carbon nanofibers (VACNFs) which serve as the current collector and structural template. Such nanostructured vertical core-shell array-electrodes enable short Li-ion diffusion path and large pseudocapacitive contribution by fast surface reactions, leading to the hybrid features of batteries and supercapacitors that can provide high specific energy over a wide range of power rates. Due to the improved mechanical stability of the infiltrated composite structure, the hybrid cell shows excellent cycling stability and is able to retain more than 95% of the original capacity after 3500 cycles. More importantly, this solid-state device can stably operate in a temperature range from -20 to 60 °C with a very low self-discharge rate and an excellent shelf life. This solid-state architecture is promising for the development of highly stable thin-film hybrid energy storage devices for unconventional applications requiring largely varied power, wider operation temperature, long shelf-life and higher safety standards.

  10. New Supercapacitors Based on the Synergetic Redox Effect between Electrode and Electrolyte

    Directory of Open Access Journals (Sweden)

    You Zhang

    2016-08-01

    Full Text Available Redox electrolytes can provide significant enhancement of capacitance for supercapacitors. However, more important promotion comes from the synergetic effect and matching between the electrode and electrolyte. Herein, we report a novel electrochemical system consisted of a polyanilline/carbon nanotube composite redox electrode and a hydroquinone (HQ redox electrolyte, which exhibits a specific capacitance of 7926 F/g in a three-electrode system when the concentration of HQ in H2SO4 aqueous electrolyte is 2 mol/L, and the maximum energy density of 114 Wh/kg in two-electrode symmetric configuration. Moreover, the specific capacitance retention of 96% after 1000 galvanostatic charge/discharge cycles proves an excellent cyclic stability. These ultrahigh performances of the supercapacitor are attributed to the synergistic effect both in redox polyanilline-based electrolyte and the redox hydroquinone electrode.

  11. Magnesium-based energy storage systems and methods having improved electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tianbiao; Li, Guosheng; Liu, Jun; Shao, Yuyan

    2016-12-20

    Electrolytes for Mg-based energy storage devices can be formed from non-nucleophilic Mg.sup.2+ sources to provide outstanding electrochemical performance and improved electrophilic susceptibility compared to electrolytes employing nucleophilic sources. The instant electrolytes are characterized by high oxidation stability (up to 3.4 V vs Mg), improved electrophile compatibility and electrochemical reversibility (up to 100% coulombic efficiency). Synthesis of the Mg.sup.2+ electrolytes utilizes inexpensive and safe magnesium dihalides as non-nucleophilic Mg.sup.2+ sources in combination with Lewis acids, MR.sub.aX.sub.3-a (for 3.gtoreq.a.gtoreq.1). Furthermore, addition of free-halide-anion donors can improve the coulombic efficiency of Mg electrolytes from nucleophilic or non-nucleophilic Mg.sup.2+ sources.

  12. Conductivity of carbonate- and perfluoropolyether-based electrolytes in porous separators

    Science.gov (United States)

    Devaux, Didier; Chang, Yu H.; Villaluenga, Irune; Chen, X. Chelsea; Chintapalli, Mahati; DeSimone, Joseph M.; Balsara, Nitash P.

    2016-08-01

    In lithium batteries, a porous separator filled with an electrolyte is placed in between the electrodes. Properties of the separator such as porosity and wettability strongly influence the conductivity of the electrolyte-separator composite. This study focuses on three commercial separators: a single layer polypropylene (Celgard 2500), a trilayer polypropylene-polyethylene-polypropylene (PP-PE-PP), and a porous polytetrafluoroethylene (PTFE). Electron microscopy was used to characterize the pore structure, and these experiments reveal large differences in pore morphology. The separators were soaked in both carbonate- and perfluoropolyether-based electrolytes. The conductivity of the neat electrolytes (σ0) varied from 6.46 × 10-6 to 1.76 × 10-2 S cm-1. The porosity and wettability of the separator affect the electrolyte uptake that in turn affect the conductivity of electrolyte-separator composites. The conductivity of the electrolyte-separator composites (σ) was found to follow a master equation, σ = 0.51·σ0·ϕc3.2±0.2, where ϕc is the volume fraction of the electrolyte in each separator.

  13. Preparation and properties of PEO/LiClO4/KH560-SiO2 composite polymer electrolyte by sol-gel composite-in-situ method

    Institute of Scientific and Technical Information of China (English)

    PAN Chun-yue; GAO Jin-huan; ZHANG Qian; FENG Qing; CHAO meng

    2008-01-01

    Composite polymer electrolytes based on polyethylene oxide (PEO) were prepared by using LiClO4 as doping salt and silane-modified SiO2 as filler. SiO2 was formed in-situ in (PEO)8LiClO4 matrix by the hydrolysis and condensation reaction of Si(OC4H9)4. The crystallinity, morphology and ionic conductivity of composite polymer electrolyte films were examined by differential scanning calorimetry, scanning electron microscopy, atom force microscopy and alternating current impedance spectroscopy, respectively. Compared with the crystallinity of the unmodified SiO2 as inert filler, that of composite polymer electrolytes is decreased. The results show that silane-modified SiO2 particles are uniformly dispersed in (PEO)8LiClO4 composite polymer electrolyte film and the addition of silane-modified SiO2 increases the ionic conductivity of the (PEO)8LiClO4 more noticeably. When the mass fraction of SiO2 is about 10%, the conductivity of (PEO)8LiClO4-modified SiO2 attains a maximum value of 4.8×10-5S·cm-1.

  14. Lithium batteries using poly(ethylene oxide)-based non-aqueous electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zonghai; Amine, Khalil

    2015-09-08

    Lithium-air cells employing poly(ethyleneoxide) phosphate-based electrolytes may be prepared and exhibit improved charge carrying capacity. Such PEO phosphates generally have the formulas IIa, IIb, IIc, where: ##STR00001##

  15. Synthesis and Compatibility of Ionic Liquid Containing Rod-Coil Polyimide Gel Electrolytes with Lithium Metal Electrodes

    Science.gov (United States)

    Tigelaar, Dean M.; Palker, Allyson E.; Meador, Mary Ann B.; Bennett, William R.

    2008-01-01

    A highly cross-linked polyimide-polyethylene oxide copolymer has been synthesized that is capable of holding large volumes of liquid component, simultaneously maintaining good dimensional stability. An amine end capped oligomer was made that was imidized in solution, followed by reaction with a triisocyanate in the presence of desired additives at ambient temperature. Polymer films are able to hold over 4 times their weight in room temperature ionic liquid RTIL or carbonate solvent. Electrolytes were studied that contained varying amounts of RTIL, lithium trifluoromethanesulfonimide LiTFSi, and alumina nanoparticles. Electrochemical stability of these electrolytes with lithium metal electrodes was studied by galvanic cycling and impedance spectroscopy. Improved cycling stability and decreased interfacial resistance were observed when increasing amounts of RTIL and LiTFSi were added. The addition of small amounts of alumina further decreased interfacial resistance by nearly an order of magnitude. During the course of the study, cycling stability increased from less than 3 to greater than 1000 h at 60 C and 0.25 mA/cm2 current density.

  16. Synthesis and Compatibility of Ionic Liquid Containing Rod-Coil Polyimide Gel Electrolytes with Lithium Metal Electrodes

    Science.gov (United States)

    Tigelaar, Dean M.; Palker, Allyson E.; Meador, Mary Ann B.; Bennett, William R.

    2008-01-01

    A highly cross-linked polyimide-polyethylene oxide copolymer has been synthesized that is capable of holding large volumes of liquid component, simultaneously maintaining good dimensional stability. An amine end capped oligomer was made that was imidized in solution, followed by reaction with a triisocyanate in the presence of desired additives at ambient temperature. Polymer films are able to hold over 4 times their weight in room temperature ionic liquid RTIL or carbonate solvent. Electrolytes were studied that contained varying amounts of RTIL, lithium trifluoromethanesulfonimide LiTFSi, and alumina nanoparticles. Electrochemical stability of these electrolytes with lithium metal electrodes was studied by galvanic cycling and impedance spectroscopy. Improved cycling stability and decreased interfacial resistance were observed when increasing amounts of RTIL and LiTFSi were added. The addition of small amounts of alumina further decreased interfacial resistance by nearly an order of magnitude. During the course of the study, cycling stability increased from less than 3 to greater than 1000 h at 60 C and 0.25 mA/cm2 current density.

  17. Enhancement of ionic conductivity of PEO based polymer electrolyte by the addition of nanosize ceramic powders.

    Science.gov (United States)

    Wang, G X; Yang, L; Wang, J Z; Liu, H K; Dou, S X

    2005-07-01

    The ionic conductivity of polyethylene oxide (PEO) based solid polymer electrolytes (SPEs) has been improved by the addition of nanosize ceramic powders (TiO2 and AL2O3). The PEO based solid polymer electrolytes were prepared by the solution-casting method. Electrochemical measurement shows that the 10 wt% TiO2 PEO-LiClO4 polymer electrolyte has the best ionic conductivity (about 10(-4) S cm(-1) at 40-60 degrees C). The lithium transference number of the 10 wt% TiO2 PEO-LiClO4 polymer electrolyte was measured to be 0.47, which is much higher than that of bare PEO polymer electrolyte. Ac impedance testing shows that the interface resistance of ceramic-added PEO polymer electrolyte is stable. Linear sweep voltammetry measurement shows that the PEO polymer electrolytes are electrochemically stable in the voltage range of 2.0-5.0 V versus a Li/Li+ reference electrode.

  18. Lithium-ion-based solid electrolyte tuning of the carrier density in graphene

    OpenAIRE

    Jialin Zhao; Meng Wang; Hui Li; Xuefu Zhang; Lixing You; Shan Qiao; Bo Gao; Xiaoming Xie; Mianheng Jiang

    2016-01-01

    We have developed a technique to tune the carrier density in graphene using a lithium-ion-based solid electrolyte. We demonstrate that the solid electrolyte can be used as both a substrate to support graphene and a back gate. It can induce a change in the carrier density as large as 1 × 1014 cm−2, which is much larger than that induced with oxide-film dielectrics, and it is comparable with that induced by liquid electrolytes. Gate modulation of the carrier density is still visible at 150 K, w...

  19. Nanocomposite polymer electrolytes based on poly(oxyethylene and cellulose whiskers

    Directory of Open Access Journals (Sweden)

    My Ahmed Saïd Azizi Samir

    2005-06-01

    Full Text Available Solid lithium-conducting nanocomposite polymer electrolytes based on poly(oxyethylene (POE were prepared from high aspect ratio cellulosic whiskers and lithium imide salt, LiTFSI. The cellulosic whiskers were extracted from tunicate -a sea animal- and consisted of slender parallelepiped rods that have an average length around 1 µm and a width close to 15 nm. High performance nanocomposite electrolytes were obtained. The filler provided a high reinforcing effect while a high level of ionic conductivity was retained with respect to unfilled polymer electrolytes. Cross-linking and plasticizing of the matrix as well as preparation of the composites from an organic medium were also investigated.

  20. Dielectric behavior of different nanofillers incorporated in PVC-PMMA based polymer electrolyte membranes

    Science.gov (United States)

    Sowmya, G.; Pradeepa, P.; Kalaiselvimary, J.; Edwinraj, S.; Prabhu, M. Ramesh

    2016-05-01

    The Poly (methyl methacrylate) (PMMA)-Poly (vinyl chloride) (PVC) based polymer electrolytes were prepared by solvent casting technique. The prepared polymer electrolytes were subjected to conductivity studies by using electrochemical impedance spectroscopy and the maximum ionic conductivity value was found to be 0.8011 × 10-3 Scm-1 at 303K for PVC (17.5wt%) - PMMA (7.5wt %) - LiClO4 (8wt %) - PC (67wt %) - BaTiO3 (8wt%) electrolyte system. The dielectric behavior of the samples also studied.

  1. Mg/O2 Battery Based on the Magnesium-Aluminum Chloride Complex (MACC) Electrolyte

    DEFF Research Database (Denmark)

    Vardar, Galin; Smith, Jeffrey G.; Thomson, Travis

    2016-01-01

    Mg/O2 cells employing a MgCl2/AlCl3/DME (MACC/DME) electrolyte are cycled and compared to cells with modified Grignard electrolytes, showing that performance of magnesium/oxygen batteries depends strongly on electrolyte composition. Discharge capacity is far greater for MACC/DME-based cells, while...... substantially and likely explains the poor rechargeability. An additional impedance rise consistent with film formation on the Mg negative electrode suggests the presence of detrimental O2 crossover. Minimizing O2 crossover and bypassing charge transfer through the discharge product would improve battery...

  2. Neutron detector based on lithiated sol-gel glass

    CERN Document Server

    Wallace, S; Miller, L F; Dai, S

    2002-01-01

    A neutron detector technology is demonstrated based on sup 6 Li/ sup 1 sup 0 B doped sol-gel glass. The detector is a sol-gel glass film coated silicon surface barrier detector (SBD). The ionized charged particles from (n, alpha) reactions in the sol-gel film enter the SBD and are counted. Data showing that gamma-ray pulse amplitudes interfere with identifying charged particles that exit the film layer with energies below the gamma-ray energy is presented. Experiments were performed showing the effect of sup 1 sup 3 sup 7 Cs and sup 6 sup 0 Co gamma rays on the SBD detector. The reaction product energies of the triton and alpha particles from sup 6 Li are significantly greater than the energies of the Compton electrons from high-energy gamma rays, allowing the measurement of neutrons in a high gamma background. The sol-gel radiation detection technology may be applicable to the characterization of transuranic waste, spent nuclear fuel and to the monitoring of stored plutonium.

  3. Application of Film-forming Additives for Ionic Liquid Based Electrolyte

    Institute of Scientific and Technical Information of China (English)

    孙敏倩; 胡志强; 蔡迎军; 董陶; 吕兴梅

    2012-01-01

    N-methyl-N-propylpiperidinium bis(trifluoromethanesulfonyl)imide was synthesized for the application in ionic liquid based electrolytes in lithium ion battery,10% vinylene carbonate (VC) and 10% 1,3-propane sultone (PS) were added to the electrolyte system respectively as additives to improve the property of solid electrolyte interface and cyclic performance.The results of cyclic voltammetry showed that homogenous and compact solid electrolyte interface film formed on graphite electrode which was detected by observing the morphology of cycled graphite anode,Charging and discharging performance of LiFePO4/Li half cell was tested in the electrolyte with or without additives.The initial specific discharging capacities were increased to 129.4 and 123.0 mA·h/g by the addition of VC and PS,respectively,compared with that of additive-free electrolyte.The discharging retentions were 88.9% and 84.6% in electrolyte containing VC and PS after 10 cycles.

  4. Thermal expansion of BaCeO{sub 3}-based solid electrolytes with proton conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Gorelov, V.P.; Arestova, N.B.; Kurumchin, E.Kh.; Vdovin, G.K. [Institute of High Temperature Electrochemistry, Ekaterinburg (Russian Federation)

    1995-03-01

    Solid electrolytes based on barium cerate BaCeO{sub 3} display high proton conductivity in hydrogen atmospheres at elevated temperatures. These materials can be used as electrolytes for fuel cells, for hydrogen and moisture sensor cells, and for separating gas mixtures, etc. Knowledge of the properties of particular ceramics is required for solving some problems related to structural materials. This work is devoted to studying the thermal expansion of BaCeO{sub 3} ceramics.

  5. Integration of gel-based and gel-free proteomic data for functional analysis of proteins through Soybean Proteome Database

    KAUST Repository

    Komatsu, Setsuko

    2017-05-10

    The Soybean Proteome Database (SPD) stores data on soybean proteins obtained with gel-based and gel-free proteomic techniques. The database was constructed to provide information on proteins for functional analyses. The majority of the data is focused on soybean (Glycine max ‘Enrei’). The growth and yield of soybean are strongly affected by environmental stresses such as flooding. The database was originally constructed using data on soybean proteins separated by two-dimensional polyacrylamide gel electrophoresis, which is a gel-based proteomic technique. Since 2015, the database has been expanded to incorporate data obtained by label-free mass spectrometry-based quantitative proteomics, which is a gel-free proteomic technique. Here, the portions of the database consisting of gel-free proteomic data are described. The gel-free proteomic database contains 39,212 proteins identified in 63 sample sets, such as temporal and organ-specific samples of soybean plants grown under flooding stress or non-stressed conditions. In addition, data on organellar proteins identified in mitochondria, nuclei, and endoplasmic reticulum are stored. Furthermore, the database integrates multiple omics data such as genomics, transcriptomics, metabolomics, and proteomics. The SPD database is accessible at http://proteome.dc.affrc.go.jp/Soybean/. Biological significanceThe Soybean Proteome Database stores data obtained from both gel-based and gel-free proteomic techniques. The gel-free proteomic database comprises 39,212 proteins identified in 63 sample sets, such as different organs of soybean plants grown under flooding stress or non-stressed conditions in a time-dependent manner. In addition, organellar proteins identified in mitochondria, nuclei, and endoplasmic reticulum are stored in the gel-free proteomics database. A total of 44,704 proteins, including 5490 proteins identified using a gel-based proteomic technique, are stored in the SPD. It accounts for approximately 80% of all

  6. Integration of gel-based and gel-free proteomic data for functional analysis of proteins through Soybean Proteome Database.

    Science.gov (United States)

    Komatsu, Setsuko; Wang, Xin; Yin, Xiaojian; Nanjo, Yohei; Ohyanagi, Hajime; Sakata, Katsumi

    2017-06-23

    The Soybean Proteome Database (SPD) stores data on soybean proteins obtained with gel-based and gel-free proteomic techniques. The database was constructed to provide information on proteins for functional analyses. The majority of the data is focused on soybean (Glycine max 'Enrei'). The growth and yield of soybean are strongly affected by environmental stresses such as flooding. The database was originally constructed using data on soybean proteins separated by two-dimensional polyacrylamide gel electrophoresis, which is a gel-based proteomic technique. Since 2015, the database has been expanded to incorporate data obtained by label-free mass spectrometry-based quantitative proteomics, which is a gel-free proteomic technique. Here, the portions of the database consisting of gel-free proteomic data are described. The gel-free proteomic database contains 39,212 proteins identified in 63 sample sets, such as temporal and organ-specific samples of soybean plants grown under flooding stress or non-stressed conditions. In addition, data on organellar proteins identified in mitochondria, nuclei, and endoplasmic reticulum are stored. Furthermore, the database integrates multiple omics data such as genomics, transcriptomics, metabolomics, and proteomics. The SPD database is accessible at http://proteome.dc.affrc.go.jp/Soybean/. The Soybean Proteome Database stores data obtained from both gel-based and gel-free proteomic techniques. The gel-free proteomic database comprises 39,212 proteins identified in 63 sample sets, such as different organs of soybean plants grown under flooding stress or non-stressed conditions in a time-dependent manner. In addition, organellar proteins identified in mitochondria, nuclei, and endoplasmic reticulum are stored in the gel-free proteomics database. A total of 44,704 proteins, including 5490 proteins identified using a gel-based proteomic technique, are stored in the SPD. It accounts for approximately 80% of all predicted proteins from

  7. A high performance flexible all solid state supercapacitor based on the MnO2 sphere coated macro/mesoporous Ni/C electrode and ionic conducting electrolyte.

    Science.gov (United States)

    Zhi, Jian; Reiser, Oliver; Wang, Youfu; Hu, Aiguo

    2016-06-09

    A high contact resistance between the active materials and the current collector, a low ionic conductivity of the gel electrolyte, and an impenetrable electrode structure are the three major barriers which greatly limit the capacitance of MnO2 in solid state supercapacitors. As a potential solution to these problems, in this work we report a novel electrode for solid state supercapacitors, based on a ternary system composed of hierarchical MnO2 spheres as the active material, macroporous Ni foam as gel penetrable skeletons and an ordered mesoporous carbon (OMC) membrane as the charge-transport accelerating layer. By employing butyl-3-methylimidazolium chloride (BMIMCl) modified gels as the ionic conducting electrolyte, the utilization efficiency of MnO2 on the specific capacitance was enhanced up to 88% of the theoretical value, delivering a volumetric capacitance of 81 F cm(-3), which is the highest value among MnO2 based solid state supercapacitors. Moreover, such a flexible device exhibits exceptional volumetric energy and power density (6.6 Wh L(-1) and 549 W L(-1), based on the whole device volume) combined with a small capacity loss of 8.5% after 6000 cycles under twisting. These encouraging findings unambiguously overcome the energy bottleneck of MnO2 in solid state supercapacitors, and open up a new application of macro/mesoporous materials in flexible devices.

  8. Lanthanum germanate-based apatites as electrolyte for SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Marrero-Lopez, D.; Diaz-Carrasco, P.; Ramos-Barrado, J.R. [Departamento de Fisica Aplicada I, Laboratorio de Materiales y Superficies (Unidad Asociada al C.S.I.C.), Universidad de Malaga, 29071 Malaga (Spain); Pena-Martinez, J. [Instituto de Energias Renovables, Parque Tecnologico, Universidad de Castilla La Mancha, 02006 Albacete (Spain); Ruiz-Morales, J.C. [Departamento de Quimica Inorganica, Universidad de La Laguna, 38200 La Laguna, Tenerife (Spain)

    2011-02-15

    Germanate apatites with composition La{sub 10-x}Ge{sub 5.5}Al{sub 0.5}O{sub 26.75-3x/2} have been evaluated for the first time as possible electrolytes for solid oxide fuel cells (SOFCs). Different electrode materials have been considered in this study, i.e. manganite, ferrite, nickelates and cobaltite as cathode materials; and NiO-CGO composite and chromium-manganite as anodes. The chemical compatibility and electrochemical performance of these electrodes with La{sub 9.8}Ge{sub 5.5}Al{sub 0.5}O{sub 26.45} have been studied by X-ray powder diffraction (XRPD) and impedance spectroscopy. The XRPD analysis did not reveal appreciable bulk reactivity with the formation of reaction products between the germanate electrolyte and these electrodes up to 1,200 C. However, a significant cation interdiffusion was observed by energy dispersive spectroscopy (EDS) at the electrode/electrolyte interface, which leads to a significant decrease of the performance of these electrodes. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Preparation and characterization of plasticized high molecular weight PVC-based polymer electrolytes

    Indian Academy of Sciences (India)

    S Ramesh; Geok Bee Teh; Rong-Fuh Louh; Yong Kong Hou; Pung Yen Sin; Lim Jing Yi

    2010-02-01

    Poly(vinyl chloride) (PVC)-based polymer electrolytes films consisting of lithium trifluromethanesulfonate (LiCF3SO3)-ethylene carbonate (EC) were prepared by the solution-casting method. Ionic conductivities of the electrolytes have been determined by an impedance studies in the temperature range of 298–373 K. Complexation of the prepared electrolytes is studied by X-ray diffraction (XRD) analysis. Thermogravimetric analysis (TGA) was used to confirm the thermal stability of the polymer electrolytes. The conductivity–temperature plots were found to follow an Arrhenius nature. All these films are found to be thermally stable until 132–167°C.

  10. Applications of porous silicon formed by electrochemical etching using an electrolyte based on HF:formaldehyde

    Science.gov (United States)

    De La Luz Merino, S.; Morales-Morales, F.; Méndez-Blas, A.; Calixto, M. E.; Nieto-Caballero, F. G.; García-Salgado, G.

    2013-06-01

    In this work, we report the experimental results on the formation of porous silicon (PSi) monolayers by electrochemical etching using a formaldehyde based electrolyte. The results were compared with PSi monolayers obtained with the traditional electrolyte (HF:ethanol). Both electrolytes facilitate the removal of H2 generated as a subproduct during the electrochemical etching process in the surface of the c-Si substrate. Formaldehyde presents a good affinity to surfaces and interfaces and the excess of water in the electrolyte reduces the pore sizes of PSi samples. The porosity and etching rate values are similar than those obtained using HF:et solutions. The refractive index values are the same in both cases at the same porosity in the visible range. The results have shown that the chemical characteristics of the ethanol and formaldehyde can give some different advantages to the PSi process and its applications.

  11. A Synopsis of Interfacial Phenomena in Lithium-Based Polymer Electrolyte Electrochemical Cells

    Science.gov (United States)

    Baldwin, Richard S.; Bennett, William R.

    2007-01-01

    The interfacial regions between electrode materials, electrolytes and other cell components play key roles in the overall performance of lithium-based batteries. For cell chemistries employing lithium metal, lithium alloy or carbonaceous materials (i.e., lithium-ion cells) as anode materials, a "solid electrolyte interphase" (SEI) layer forms at the anode/electrolyte interface, and the properties of this "passivating" layer significantly affect the practical cell/battery quality and performance. A thin, ionically-conducting SEI on the electrode surface can beneficially reduce or eliminate undesirable side reactions between the electrode and the electrolyte, which can result in a degradation in cell performance. The properties and phenomena attributable to the interfacial regions existing at both anode and cathode surfaces can be characterized to a large extent by electrochemical impedance spectroscopy (EIS) and related techniques. The intention of the review herewith is to support the future development of lithium-based polymer electrolytes by providing a synopsis of interfacial phenomena that is associated with cell chemistries employing either lithium metal or carbonaceous "composite" electrode structures which are interfaced with polymer electrolytes (i.e., "solvent-free" as well as "plasticized" polymer-binary salt complexes and single ion-conducting polyelectrolytes). Potential approaches to overcoming poor cell performance attributable to interfacial effects are discussed.

  12. A polymer gel electrolyte composed of a poly(ethylene oxide) copolymer and the influence of its composition on the dynamics and performance of dye-sensitized solar cells

    Science.gov (United States)

    Benedetti, João E.; Gonçalves, Agnaldo D.; Formiga, André L. B.; De Paoli, Marco-A.; Li, X.; Durrant, James R.; Nogueira, Ana F.

    A polymer gel electrolyte composed of a poly(ethylene oxide) derivative, poly(ethylene oxide-co-2-(2-methoxyethoxy) ethyl glycidyl ether), mixed with gamma-butyrolactone (GBL), LiI and I 2 is employed in dye sensitized solar cells (DSSC). The electrolyte is characterized by conductivity experiments, Raman spectroscopy and thermal analysis. The influence of the electrolyte composition on the kinetics of DSSC is also investigated by transient absorption spectroscopy (TAS). The electrolyte containing 70 wt.% of GBL and 20 wt.% of LiI presents the highest conductivity (1.9 × 10 -3 S cm -1). An efficiency of 4.4% is achieved using this composition. The increase in I SC as a function of GBL can be attributed an increase in the mobility of the iodide (polyiodide) species. The increase in the yield of the intermediate species, I 2 -, originating in the regeneration reaction, is confirmed by TAS. However, the charge recombination process is faster at this composition and a decrease in the V oc is observed. Photovoltage decay experiments confirm an acceleration in charge recombination for the DSSC assembled with the electrolyte containing more GBL. Raman investigations show that in this electrolyte the I 5 -/I 3 - ratio is higher. Theoretical calculations also indicate that the I 5 - species is a better electron acceptor.

  13. A polymer gel electrolyte composed of a poly(ethylene oxide) copolymer and the influence of its composition on the dynamics and performance of dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Benedetti, Joao E.; Goncalves, Agnaldo D.; Formiga, Andre L.B.; De Paoli, Marco-A.; Nogueira, Ana F. [Institute of Chemistry, University of Campinas - UNICAMP, P.O. Box 6154, 13083-970 Campinas, SP (Brazil); Li, X.; Durrant, James R. [Centre for Electronic Materials and Devices, Imperial College of Science Technology and Medicine, London SW7 2AY (United Kingdom)

    2010-02-15

    A polymer gel electrolyte composed of a poly(ethylene oxide) derivative, poly(ethylene oxide-co-2-(2-methoxyethoxy) ethyl glycidyl ether), mixed with gamma-butyrolactone (GBL), LiI and I{sub 2} is employed in dye sensitized solar cells (DSSC). The electrolyte is characterized by conductivity experiments, Raman spectroscopy and thermal analysis. The influence of the electrolyte composition on the kinetics of DSSC is also investigated by transient absorption spectroscopy (TAS). The electrolyte containing 70 wt.% of GBL and 20 wt.% of LiI presents the highest conductivity (1.9 x 10{sup -3} S cm{sup -1}). An efficiency of 4.4% is achieved using this composition. The increase in I{sub SC} as a function of GBL can be attributed an increase in the mobility of the iodide (polyiodide) species. The increase in the yield of the intermediate species, I{sub 2}{sup -}, originating in the regeneration reaction, is confirmed by TAS. However, the charge recombination process is faster at this composition and a decrease in the V{sub oc} is observed. Photovoltage decay experiments confirm an acceleration in charge recombination for the DSSC assembled with the electrolyte containing more GBL. Raman investigations show that in this electrolyte the I{sub 5}{sup -}/I{sub 3}{sup -} ratio is higher. Theoretical calculations also indicate that the I{sub 5}{sup -} species is a better electron acceptor. (author)

  14. Study on {gamma}-butyrolactone for LiBOB-based electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Jia-yuan; Kang, Xiao-li; Yu, Zhao-xin; Xu, Ting-ting; Qiu, Wei-hua [Beijing Key Lab. of New Energy Materials and Technologies, School of Material Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Liu, Xing-jiang [China Electronics Technology Group Corporation, Tianjin Institute of Power Sources, Tianjin 300381 (China)

    2009-04-01

    To solve the problems of LiBOB-based electrolytes, small salt solubility and low conductivity, a sort of cyclic carboxylate, {gamma}-butyrolactone (GBL) was applied in the lithium-ion battery electrolyte as the main solvent of lithium bis(oxalate)borate (LiBOB). LiBOB-GBL electrolyte exhibits good electrochemical stability, which is suitable to be the candidate of the lithium-ion battery electrolyte. Using GBL as the solvent of the LiBOB salt can increase the solubility and conductivity dramatically. At room temperature, LiFePO{sub 4}/LiBOB-GBL/Li half cell shows satisfying cycle performance with no capacity fading in the first 50 cycles and promising capacity performance with stable discharge capacity of about 125 mAh g{sup -1}. EA is mixed with GBL to get lower viscosity solvent. In LiFePO{sub 4}/Li half cell with 0.5 C discharge rate, 0.2 M LiBOB-GBL/EA (1:1, wt) electrolyte exhibits best at room temperature and 0.7 M LiBOB-GBL/EA (1:1, wt) electrolyte exhibits best at elevated temperature. (author)

  15. Liquid electrolytes based on new lithium conductive imidazole salts

    Energy Technology Data Exchange (ETDEWEB)

    Niedzicki, L.; Kasprzyk, M.; Kuziak, K.; Zukowska, G.Z.; Marcinek, M.; Wieczorek, W. [Department of Chemistry, Warsaw University of Technology, Noakowskiego 3, 00-664 Warsaw (Poland); Armand, M. [LRCS, University de Picardie Jules Verne, UMR 6007 CNRS, 33 rue de Saint-Leu, 80039 Amiens (France)

    2011-02-01

    In the present paper new generation of imidazole-derived lithium salts (LiTDI - lithium 4,5-dicyano-2-(trifluoromethyl)imidazolide, LiPDI - lithium 4,5-dicyano-2-(pentafluoroethyl)imidazolide and LiHDI - lithium 4,5-dicyano-2-(n-heptafluoropropyl)imidazolide) applied in a model liquid electrolyte, with propylene carbonate used as a solvent, is described. Room temperature ionic conductivities measured by Impedance Spectroscopy are as high as 10{sup -2} to 10{sup -3} S cm{sup -1} for the 0.1-1 mol dm{sup -3} salt concentration range. Lithium cation transference numbers calculated using the Bruce-Vincent method exceed 0.4 at salt concentration equal to 1 mol dm{sup -3}. Interface resistance measurements showed good stability at high - 0.5 mol dm{sup -3} or low - 0.01 mol dm{sup -3} salt concentrations. Ionic associations were estimated using Fuoss-Kraus semiempirical method revealing relatively low association rates. The effect of anion structure on ionic interactions and electrochemical characteristics of the studied electrolytes is discussed. (author)

  16. Characterizations of Chitosan-Based Polymer Electrolyte Photovoltaic Cells

    Directory of Open Access Journals (Sweden)

    M. H. Buraidah

    2010-01-01

    Full Text Available The membranes 55 wt.% chitosan-45 wt.% NH4I, 33 wt.% chitosan-27 wt.% NH4I-40 wt.% EC, and 27.5 wt.% chitosan-22.5 wt.% NH4I-50 wt.% buthyl-methyl-imidazolium-iodide (BMII exhibit conductivity of 3.73×10−7, 7.34×10−6, and 3.43×10−5 S cm−1, respectively, at room temperature. These membranes have been used in the fabrication of solid-state solar cells with configuration ITO/TiO2/polymer electrolyte membrane/ITO. It is observed that the short-circuit current density increases with conductivity of the electrolyte. The use of anthocyanin pigment obtained by solvent extraction from black rice and betalain from the callus of Celosia plumosa also helps to increase the short-circuit current.

  17. Cycle stability of the electrochemical capacitors patterned with vertically aligned carbon nanotubes in an LiPF6-based electrolyte

    Science.gov (United States)

    Chiou, Yi-Deng; Tsai, Dah-Shyang; Lam, Hoa Hung; Chang, Chuan-Hua; Lee, Kuei-Yi; Huang, Ying-Sheng

    2013-08-01

    The miniature ultracapacitors, with interdigitated electrodes of vertically aligned carbon nanotubes (VACNTs) and an inter-electrode gap of 20 μm, have been prepared in the LiPF6 organic electrolyte with and without PVdF-HFP gel. PVdF-HFP between two opposing electrodes enhances the device reliability, but lessens its power performance because of the extra diffusion resistance. Also noteworthy are the gel influences on the cycle stability. When the applied voltage is 2.0 or 2.5 V, both the LiPF6 and the gel capacitors exhibit excellent stability, typified by a retention ratio of >=95% after 10 000 cycles. Their coulombic efficiencies quickly rise up, and hold steady at 100%. Nonetheless, when the applied voltage is 3.5 or 4.0 V, the cycle stability deteriorates, since the negative electrode potential descends below 0.9 V (vs. Li), leading to electrolyte decomposition and SEI formation. For the LiPF6 capacitor, its retention ratio could be around 60% after 10 000 cycles and the coulombic efficiency of 100% is difficult to reach throughout its cycle life. On the other hand, the gel capacitor cycles energy with a much higher retention ratio, >80% after 10 000 cycles, and a better coulombic efficiency, even though electrolyte decomposition still occurs. We attribute the superior stability of the gel capacitor to its extra diffusion resistance which slows down the performance deterioration.

  18. Toward garnet electrolyte-based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface.

    Science.gov (United States)

    Fu, Kun Kelvin; Gong, Yunhui; Liu, Boyang; Zhu, Yizhou; Xu, Shaomao; Yao, Yonggang; Luo, Wei; Wang, Chengwei; Lacey, Steven D; Dai, Jiaqi; Chen, Yanan; Mo, Yifei; Wachsman, Eric; Hu, Liangbing

    2017-04-01

    Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet-type Li7La3Zr2O12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10(-3) to 10(-4) S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnet solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm(2) for the pristine garnet/Li and 75 ohm·cm(2) for the surface-engineered garnet/Li. Li7La2.75Ca0.25Zr1.75Nb0.25O12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries.

  19. Synthesis and Ionic Conductivity of Siloxane Based Polymer Electrolytes with Propyl Butyrate Pendant Groups

    Energy Technology Data Exchange (ETDEWEB)

    Jalagonia, Natia; Tatrishvili, Tamara; Markarashvili, Eliza; Aneli, Jimsher; Mukbaniani, Omar [Javakhishvili Tbilisi State University, Tbilisi (Georgia); Grazulevicius, Jouzas Vidas [Kaunas University of Technology, Kaunas (Lithuania)

    2016-02-15

    Hydrosilylation reactions of 2.4.6.8-tetrahydro-2.4.6.8-tetramethylcyclotetrasiloxane with allyl butyrate catalyzed by Karstedt's, H2PtCl6 and Pt/C catalyst were studied and 2.4.6.8-tetra (propyl butyrate)-2.4.6.8-tetramethylcyclotetrasiloxane was obtained. The reaction order, activation energies and rate constants were determined. Ringopening polymerization of 2.4.6.8-tetra (propyl butyrate)-2.4.6.8-tetramethylcyclotetrasiloxane in the presence of CaF2, LiF, KF and anhydrous potassium hydroxide in 60-70 .deg. C temperature range was carried out and methylsiloxane oligomers with regular arrangement of propyl butyrate pendant groups were obtained. The synthesized products were studied by FTIR and NMR spectroscopy. The polysiloxanes were characterized by wide-angle X-ray, gel-permeation chromatography and DSC analyses. Via sol-gel processes of oligomers doped with lithium trifluoromethylsulfonate or lithium bis (trifluoromethylsulfonyl)imide, solid polymer electrolyte membranes were obtained. The dependences of ionic conductivity of obtained polyelectrolytes on temperature and salt concentration were investigated, and it was shown that electric conductivity of the polymer electrolyte membranes at room temperature changed in the range 3.5x10{sup -4} - 6.4xa0{sup -7} S/cm.

  20. Application of LiBOB-based liquid electrolyte in co-sensitized solar cell

    Science.gov (United States)

    Jun, H. K.; Buraidah, M. H.; Noor, M. M.; Kufian, M. Z.; Majid, S. R.; Sahraoui, B.; Arof, A. K.

    2013-11-01

    Co-sensitized solar cells have been fabricated using metal complex N3 dye and Ag2S/CdS quantum dots coupled with LiBOB-based liquid electrolyte. Quantum dots (QDs) were synthesized via the successive ionic layer adsorption and reaction (SILAR) route. The absorbance and band gap energy of Ag2S and CdS QDs were determined. Their refractive indices were observed to be in the range of 1.5175-1.5200. It has been shown that LiBOB-based liquid electrolyte is able to function in the QD/N3 dye co-sensitized solar cells but some stability issues of the QD were observed in the electrolyte system containing iodide whereby the QD-sensitized TiO2 was easily etched. Overall efficiencies and fill factors of the co-sensitized solar cells varied from 0.98% to 1.66% and 40% to 46% respectively. CdS QD was shown to be effective when coupled with polysulfide electrolyte while Ag2S QD was favorable towards the LiBOB-based liquid electrolyte.

  1. A Safer Sodium-Ion Battery Based on Nonflammable Organic Phosphate Electrolyte.

    Science.gov (United States)

    Zeng, Ziqi; Jiang, Xiaoyu; Li, Ran; Yuan, Dingding; Ai, Xinping; Yang, Hanxi; Cao, Yuliang

    2016-09-01

    Sodium-ion batteries are now considered as a low-cost alternative to lithium-ion technologies for large-scale energy storage applications; however, their safety is still a matter of great concern for practical applications. In this paper, a safer sodium-ion battery is proposed by introducing a nonflammable phosphate electrolyte (trimethyl phosphate, TMP) coupled with NaNi0.35Mn0.35Fe0.3O2 cathode and Sb-based alloy anode. The physical and electrochemical compatibilities of the TMP electrolyte are investigated by igniting, ionic conductivity, cyclic voltammetry, and charge-discharge measurements. The results exhibit that the TMP electrolyte with FEC additive is completely nonflammable and has wide electrochemical window (0-4.5 V vs. Na/Na(+)), in which both the Sb-based anode and NaNi0.35Mn0.35Fe0.3O2 cathode show high reversible capacity and cycling stability, similarly as in carbonate electrolyte. Based on these results, a nonflammable sodium-ion battery is constructed by use of Sb anode, NaNi0.35Mn0.35Fe0.3O2 cathode, and TMP + 10 vol% FEC electrolyte, which works very well with considerable capacity and cyclability, demonstrating a promising prospect to build safer sodium-ion batteries for large-scale energy storage applications.

  2. Development and Characterization of Poly(1-vinylpyrrolidone-co-vinyl acetate Copolymer Based Polymer Electrolytes

    Directory of Open Access Journals (Sweden)

    Nurul Nadiah Sa’adun

    2014-01-01

    Full Text Available Gel polymer electrolytes (GPEs are developed using poly(1-vinylpyrrolidone-co-vinyl acetate [P(VP-co-VAc] as the host polymer, lithium bis(trifluoromethane sulfonimide [LiTFSI] as the lithium salt and ionic liquid, and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl imide [EMImTFSI] by using solution casting technique. The effect of ionic liquid on ionic conductivity is studied and the optimum ionic conductivity at room temperature is found to be 2.14 × 10−6 S cm−1 for sample containing 25 wt% of EMImTFSI. The temperature dependence of ionic conductivity from 303 K to 353 K exhibits Arrhenius plot behaviour. The thermal stability of the polymer electrolyte system is studied by using thermogravimetric analysis (TGA while the structural and morphological properties of the polymer electrolyte is studied by using Fourier transform infrared (FTIR spectroscopy and X-ray diffraction analysis (XRD, respectively.

  3. Analysis of SEI formed with cyano-containing imidazolium-based ionic liquid electrolyte in lithium secondary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Liwei; Yamaki, Jun-ichi [Institute for Materials Chemistry and Engineering, Kyushu University, 6-1 Kasuga-Koen, Kasuga, Fukuoka 816-8580 (Japan); Egashira, Minato [Department of Applied Chemistry and Chemical Engineering, Faculty of Engineering, Yamaguchi University, 2-16-1, Yamaguchi 755-8611 (Japan)

    2007-12-06

    Two kinds of cyano-containing imidazolium-based ionic liquid, 1-cyanopropyl-3-methylimidazolium-bis(trifluoromethanesulfonyl)imide (CpMI-TFSI) and 1-cyanomethyl-3-methylimidazolium-bis(trifluoromethanesulfonyl)imide (CmMI-TFSI), each of which contained 20 wt% dissolved LiTFSI, were used as electrolytes for lithium secondary batteries. Compared with 1-ethyl-3-methylimidazolium-bis(trifluoromethane-sulfonyl)imide (EMI-TFSI) electrolyte, a reversible lithium deposition/dissolution on a stainless-steel working electrode was observed during CV measurements in these cyano-containing electrolytes, which indicated that a passivation layer (solid electrolyte interphase, SEI) was formed during potential scanning. The morphology of the working electrode with each electrolyte system was studied by SEM. Different dentrite forms were found on the electrodes with each electrolyte. The SEI that formed in CpMI-TFSI electrolyte showed the best passivating effect, while the deposited film formed in EMI-TFSI electrolyte showed no passivating effect. The chemical characteristics of the deposited films on the working electrodes were compared by XPS measurements. A component with a cyano group was found in SEIs in CpMI-TFSI and CmMI-TFSI electrolytes. The introduction of a cyano functional group suppressed the decomposition of electrolyte and improved the cathodic stability of the imidazolium-based ionic liquid. The reduction reaction route of imidazolium-based ionic liquid was considered to be different depending on whether or not the molecular structure contained a cyano functional group. (author)

  4. Quasi-Solid-State Dye-Sensitized Solar Cell Fabricated from Ionic Gel Electrolyte with High Gel-to-Solution Transition Temperature%高相转变温度的离子凝胶电解质基准固态染料敏化太阳电池

    Institute of Scientific and Technical Information of China (English)

    桃李; 霍志鹏; 王露; 戴松元

    2015-01-01

    , and intensity-modulated photocurrent and photovoltage spectroscopy (IMPS and IMVS) measurements. Electron recombination at the TiO2 photoanode/electrolyte interface was accelerated by the cross-linked gel network. The shorter electron recombination lifetime decreased the photoelectric conversion efficiency of the QS-DSC, compared with the ILE-based DSC. The photoelectric conversion efficiency of the QS-DSC exhibited no change during accelerated aging test for 1000 h, while that of the ILE-based DSC decreased to 86% of its initial value.

  5. The Effect of Titania-coating on Electrochemical Characteristics of CMS in PC-Based Electrolyte

    Institute of Scientific and Technical Information of China (English)

    J. Gao; L. C. Yang; T. Zhang; Y.P. Wu; H.Q. Wu

    2005-01-01

    @@ 1Introduction Lithium-ion batteries have been widely used in portable electronic devices due to their high voltage and high energy density. Most research has concentrated on improving their performance such as capacity, cycling characteristics and low temperature range. Propylene carbonate (PC)-based electrolytes are more desirable than ethylene carbonate (EC)-based electrolytes because of their low-temperature characteristics[1]. Unfortunately, PC is not used in commercial lithium-ion batteries because solvent decomposition and graphite exfoliation occur when lithium intercalates[2].

  6. A new composite polymer electrolyte based on poly(ethyleneoxide)/polysiloxane/BMImTFSI/organomontmorillonite

    Institute of Scientific and Technical Information of China (English)

    Yue-Jiao Li; Feng Wu; Hu-Ren Chao; Shi Chen

    2013-01-01

    Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite (PEO-PDMS/IL/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB1OO-OMMT4 was 2.19 × 10-3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.

  7. High temperature stable Li-ion battery separators based on polyetherimides with improved electrolyte compatibility

    Science.gov (United States)

    l'Abee, Roy; DaRosa, Fabien; Armstrong, Mark J.; Hantel, Moritz M.; Mourzagh, Djamel

    2017-03-01

    We report (electro-)chemically stable, high temperature resistant and fast wetting Li-ion battery separators produced through a phase inversion process using novel polyetherimides (PEI) based on bisphenol-aceton diphthalic anhydride (BPADA) and para-phenylenediamine (pPD). In contrast to previous studies using PEI based on BPADA and meta-phenylenediamine (mPD), the separators reported herein show limited swelling in electrolytes and do not require fillers to render sufficient mechanical strength and ionic conductivity. In this work, the produced 15-25 μm thick PEI-pPD separators show excellent electrolyte compatibility, proven by low degrees of swelling in electrolyte solvents, low contact angles, fast electrolyte wicking and high electrolyte uptake. The separators cover a tunable range of morphologies and properties, leading to a wide range of ionic conductivities as studied by Electrochemical Impedance Spectroscopy (EIS). Dynamic Mechanical Analysis (DMA) demonstrated dimensional stability up to 220 °C. Finally, single layer graphite/lithium nickel manganese cobalt oxide (NMC) pouch cells were assembled using this novel PEI-pPD separator, showing an excellent capacity retention of 89.3% after 1000 1C/2C cycles, with a mean Coulombic efficiency of 99.77% and limited resistance build-up. We conclude that PEI-pPD is a promising new material candidate for high performance separators.

  8. Lithium ion conducting solid polymer blend electrolyte based on bio-degradable polymers

    Indian Academy of Sciences (India)

    Natarajan Rajeswari; Subramanian Selvasekarapandian; Moni Prabu; Shunmugavel Karthikeyan; C Sanjeeviraja

    2013-04-01

    Lithium ion conducting polymer blend electrolyte films based on poly(vinyl alcohol) (PVA) and poly(vinyl pyrrolidone) (PVP) with different Mwt% of lithium nitrate (LiNO3) salt, using a solution cast technique, have been prepared. The polymer blend electrolyte has been characterized by XRD, FTIR, DSC and impedance analyses. The XRD study reveals the amorphous nature of the polymer electrolyte. The FTIR study confirms the complex formation between the polymer and salt. The shifts in g values of 70 PVA–30 PVP blend and 70 PVA–30 PVP with different Mwt% of LiNO3 electrolytes shown by DSC thermograms indicate an interaction between the polymer and the salt. The dependence of g and conductivity upon salt concentration has been discussed. The ion conductivity of the prepared polymer electrolyte has been found by a.c. impedance spectroscopic analysis. The PVA–PVP blend system with a composition of 70 wt% PVA: 30 wt% PVP exhibits the highest conductivity of 1.58 × 10-6 Scm-1 at room temperature. Polymer samples of 70 wt% PVA–30 wt% PVP blend with different molecular weight percentage of lithium nitrate with DMSO as solvent have been prepared and studied. High conductivity of 6.828 × 10-4 Scm-1 has been observed for the composition of 70 PVA:30 PVP:25 Mwt% of LiNO3 with low activation energy 0.2673 eV. The conductivity is found to increase with increase in temperature. The temperature dependent conductivity of the polymer electrolyte follows the Arrhenius relationship which shows hopping of ions in the polymer matrix. The relaxation parameters () and () of the complexes have been calculated by using loss tangent spectra. The mechanical properties of polymer blend electrolyte such as tensile strength, elongation and degree of swelling have been measured and the results are presented.

  9. Polymer electrolytes based on room temperature ionic liquid: 2,3-dimethyl-1-octylimidazolium triflate.

    Science.gov (United States)

    Singh, Boor; Sekhon, S S

    2005-09-01

    Room temperature ionic liquid (DMOImTf) based upon 2,3-dimethyl-1-octylimidazolium cation and trifluoromethanesulfonate or triflate (CF(3)SO(3))(-) anion has been synthesized and shows conductivity of 5.68 mS/cm and viscosity of 26.4 cP at 25 degrees C. Ion conducting polymer electrolytes based on polymers (poly(ethylene oxide) (PEO) and polyvinylidenefluoride-co-hexafluoropropylene (PVdF-HFP)) and ionic liquid (DMOImTf) were prepared in film form by the casting technique. The conductivity of polymer electrolytes containing 0.5 M LiCF(3)SO(3) in PEO:DMOImTf taken in equal weight ratio increases with the addition of propylene carbonate (PC) while its mechanical stability improved by dispersing nanosize fumed silica. However, polymer electrolytes containing PVdF-HFP and ionic liquid show a high value of conductivity (10(-4)-10(-3) S/cm) alongwith better mechanical stability.

  10. Hardness analysis and morphological characterization of copper-zinc alloys produced in pyrophosphate-based electrolytes

    Directory of Open Access Journals (Sweden)

    Lilian Ferreira de Senna

    2005-09-01

    Full Text Available In this work, copper-zinc alloy coatings on mild steel substrates were obtained in nontoxic pyrophosphate-based electrolytes, at room temperature and under continuous current. The effects of bath composition and current density on the hardness of the coatings, as well as on their morphologies, were evaluated. The results showed that the electrolyte composition, and the use of stress relieving additives strongly influence the hardness of the coatings, while the current density directly affect their morphology. Hence, for a current density of 116 A/m², copper-zinc alloy deposits with no pores or cracks were produced in a pyrophosphate-based electrolyte, especially when allyl alcohol was added to the solution.

  11. Layered double hydroxides as an effective additive in polymer gelled electrolyte based dye-sensitized solar cells.

    Science.gov (United States)

    Ho, Hsu-Wen; Cheng, Wei-Yun; Lo, Yu-Chun; Wei, Tzu-Chien; Lu, Shih-Yuan

    2014-10-22

    Layered double hydroxides (LDH), a class of anionic clay materials, were developed as an effective additive for polymer gelled electrolytes for use in dye-sensitized solar cells (DSSC). Carbonate and chloride intercalated Zn-Al LDHs, ZnAl-CO3 LDH, and ZnAl-Cl LDH were prepared with coprecipitation methods. The addition of the two LDHs significantly improved, in terms of power conversion efficiency (PCE), over the plain poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) gelled electrolyte and competed favorably with the liquid electrolyte based DSSCs, 8.13% for the liquid electrolyte, 7.48% for the plain PVDF-HFP gelled electrolyte, 8.11% for the ZnAl-CO3 LDH/PVDF-HFP gelled electrolyte, and 8.00% for the ZnAl-Cl LDH/PVDF-HFP gelled electrolyte based DSSCs. The good performance in PCEs achieved by the LDH-loaded DSSCs came mainly from the significant boost in open circuit voltages (Voc), from 0.74 V for both the liquid electrolyte and PVDF-HFP gelled electrolyte based DSSCs to 0.79 V for both the ZnAl-CO3 LDH/PVDF-HFP and ZnAl-Cl LDH/PVDF-HFP gelled electrolyte based DSSCs. The boost in Voc was contributed mainly by the positive shift in redox potential of the redox couple, I(-)/I3(-), as revealed from cyclic voltammetry analyses. As for the long-term stability, PCE retention rates of 96 and 99% after 504 h were achieved by the ZnAl-CO3 LDH/PVDF-HFP and ZnAl-Cl LDH/PVDF-HFP gelled electrolyte based DSSCs, respectively, appreciably better than 92% achieved by the liquid electrolyte based one after 480 h.

  12. Water-gel for gating graphene transistors.

    Science.gov (United States)

    Kim, Beom Joon; Um, Soong Ho; Song, Woo Chul; Kim, Yong Ho; Kang, Moon Sung; Cho, Jeong Ho

    2014-05-14

    Water, the primary electrolyte in biology, attracts significant interest as an electrolyte-type dielectric material for transistors compatible with biological systems. Unfortunately, the fluidic nature and low ionic conductivity of water prevents its practical usage in such applications. Here, we describe the development of a solid state, megahertz-operating, water-based gate dielectric system for operating graphene transistors. The new electrolyte systems were prepared by dissolving metal-substituted DNA polyelectrolytes into water. The addition of these biocompatible polyelectrolytes induced hydrogelation to provide solid-state integrity to the system. They also enhanced the ionic conductivities of the electrolytes, which in turn led to the quick formation of an electric double layer at the graphene/electrolyte interface that is beneficial for modulating currents in graphene transistors at high frequencies. At the optimized conditions, the Na-DNA water-gel-gated flexible transistors and inverters were operated at frequencies above 1 MHz and 100 kHz, respectively.

  13. Electrochemical cell studies based on non-aqueous magnesium electrolyte for electric double layer capacitor applications

    Energy Technology Data Exchange (ETDEWEB)

    Chandrasekaran, Ramasamy; Ishikawa, Masashi [Department of Chemistry and Materials Engineering, Faculty of Chemistry, Materials and Bioengineering, Kansai University, 3-3-35 Yamate-cho, Suita 564-8680 (Japan); Koh, Meiten; Yamauchi, Akiyoshi [Chemical Division, Fundamental Research Department, Daikin Industries Ltd., 1-1 Nishihitotsuya, Settsu 565-8585 (Japan)

    2010-01-15

    Performances of electric double layer capacitors (EDLCs) based on an activated carbon electrode with acetonitrile (ACN), propylene carbonate (PC), or a ternary electrolyte, i.e., PC:ethylene carbonate (EC):diethyl carbonate (DEC), at 1 mol dm{sup -3} of magnesium perchlorate [Mg(ClO{sub 4}){sub 2}] salt have been investigated. The electrochemical responses were studied by impedance spectroscopy, cyclic voltammetry, and galvanostatic charge-discharge experiments at 25 C in a three-electrode configuration. For a comparative evaluation, lithium perchlorate (LiClO{sub 4}) salt-based systems were also evaluated. All the observed results showed typical EDLC characteristics within the potential range between 0 and 1 V vs. an Ag/Ag{sup +} reference electrode. The Mg-based systems exhibited similar or rather better performances than the corresponding Li-based electrolytes; in particular, the rate capability of Mg-based ACN and PC electrolytes was much better than the corresponding Li-based electrolytes, indicating the high accessibility and utility of activated carbon pores by solvated Mg ions. (author)

  14. Electrochemical cell studies based on non-aqueous magnesium electrolyte for electric double layer capacitor applications

    Science.gov (United States)

    Chandrasekaran, Ramasamy; Koh, Meiten; Yamauchi, Akiyoshi; Ishikawa, Masashi

    Performances of electric double layer capacitors (EDLCs) based on an activated carbon electrode with acetonitrile (ACN), propylene carbonate (PC), or a ternary electrolyte, i.e., PC:ethylene carbonate (EC):diethyl carbonate (DEC), at 1 mol dm -3 of magnesium perchlorate [Mg(ClO 4) 2] salt have been investigated. The electrochemical responses were studied by impedance spectroscopy, cyclic voltammetry, and galvanostatic charge-discharge experiments at 25 °C in a three-electrode configuration. For a comparative evaluation, lithium perchlorate (LiClO 4) salt-based systems were also evaluated. All the observed results showed typical EDLC characteristics within the potential range between 0 and 1 V vs. an Ag/Ag + reference electrode. The Mg-based systems exhibited similar or rather better performances than the corresponding Li-based electrolytes; in particular, the rate capability of Mg-based ACN and PC electrolytes was much better than the corresponding Li-based electrolytes, indicating the high accessibility and utility of activated carbon pores by solvated Mg ions.

  15. Efficient sodium storage: Experimental study of anode with additive-free ether-based electrolyte system

    Science.gov (United States)

    Dutta, Prasit Kumar; Mitra, Sagar

    2017-05-01

    Widely used conductive carbon is found to be a major capacity contributor towards the sodium storage while used in electrode composition, in conjunction with NaClO4-PC electrolyte. Experimental studies show that the surface adsorbed sodium is present, confirmed by microscopic and XRD analysis. This unexpected property towards sodium storage in electrode conceals the electrochemical contributions expected from an active material. As the conductive carbon is a desirable component in sodium battery development, therefore this contribution needs to be optimized with respect to Coulombic efficiency. In order to investigate and optimize the unwanted capacity contribution from carbon containing electrode, we introduce an electrolyte system comprise of NaClO4-TEGDME, a low-cost electrolyte over extensively used PC-based compositions. This electrolyte composition controls the reversible capacity contribution to a minimum from the conductive carbon, and showed up to ∼97% reversibility with adequate stability till 100 cycles, within the potential range from 0.1 to 3 V. A detailed experimental analysis has been carried out to establish the electrolyte composition against conductive carbon.

  16. Ambient Temperature Hybrid Polymer Electrolyte Based on Pvk + Pvdf-Hfp for Lithium Batteries

    Science.gov (United States)

    Michael, M. S.; Prabaharan, S. R. S.

    2002-12-01

    Proposed herein is a new ambient temperature Li+ conducting PVDF-HFP-co-polymer based hybrid polymer electrolyte with polyvinyl carbozole (PVK) as additive. The addition of the latter provides high ambient temperature electrolytic conductivity (σi) 0.7 × 10-3S/cm with an ionic transference number of 0.6, besides providing the thermoplastic flexibility to the whole matrix. The membrane is found to exhibit a wide electrochemical potential window, >4.5V against Li/Li+. When prepared properly, the membrane is dry and free standing, yet totally suitable for lithium polymer rechargeable batteries. This paper presents the preparation, microstructure and electrochemical characteristics of this new hybrid polymeric membrane. Finally, the dry polymeric electrolyte membrane has been employed in a lithium polymer cell against LT-LiCo0.8Ni0.2O2 as positive electrode and its interfacial behavior and electrochemical cycling results are presented.

  17. Investigations on Poly (ethylene oxide) (PEO) - blend based solid polymer electrolytes for sodium ion batteries

    Science.gov (United States)

    Koduru, H. K.; Iliev, M. T.; Kondamareddy, K. K.; Karashanova, D.; Vlakhov, T.; Zhao, X.-Z.; Scaramuzza, N.

    2016-10-01

    Polymer blend electrolytes based on Polyethylene oxide (PEO) and polyvinyl pyrrolidone (PVP), complexed with NaIO4 salt and Graphene oxide (GO) are investigated in the present report. The electrolytes are prepared by a facile solution cast technique. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) are employed to study the influence of ion-polymer interactions on the micro structural properties of blend electrolytes. Measurements of electrical conductivity of the blend polymer complexes have been performed by using complex impedance spectroscopy in the frequency range 1 Hz - 1 MHz and within the temperature range 303 K - 343 K.A study on electrical conductivity properties of GO doped ‘salt complexed electrolyte’ systems is presented.

  18. Photocured PEO-based solid polymer electrolyte and its application to lithium-polymer batteries

    Science.gov (United States)

    Kang, Yongku; Kim, Hee Jung; Kim, Eunkyoung; Oh, Bookeun; Cho, Jae Hyun

    A solid polymer electrolyte (SPE) based on polyethylene oxide (PEO) is prepared by photocuring of polyethylene glycol acrylates. The conductivity is greatly enhanced by adding low molecular weight poly(ethylene glycol) dimethylether (PEGDME). The maximum conducticity is 5.1×10 -4 S cm -1 at 30°C. These electrolytes display oxidation stability up to 4.5 V against a lithium reference electrode. Reversible electrochemical plating/stripping of lithium is observed on a stainless steel electrode. Li/SPE/LiMn 2O 4 as well as C(Li)/SPE/LiCoO 2 cells have been fabricated and tested to demonstrate the applicability of the resulting polymer electrolytes in lithium-polymer batteries.

  19. Molecular Dynamics Simulation Study of PEO-Based Nanocomposite Polymer Electrolytes el

    Science.gov (United States)

    Borodin, Oleg; Bandyopadhyaya, Rajdip; Smith, Grant D.

    2002-03-01

    Solid polymer electrolytes exhibit good chemical, electrochemical and photochemical stability in combination with good mechanical properties, ease of processing and adequate conductivity at elevated temperatures. Addition of solid nanoparticle fillers such as TiO2 and SiO2 to lithium solid polymer electrolytes is known to improve mechanical properties, interfacial stability, conductivity and transfer numbers, particularly for poly(ethylene oxide) (PEO) based polymer electrolytes. We have performed molecular dynamics simulations of PEO/LiBF4 and PEO/LiBF4/TiO2 systems in order to study changes of the structure and mechanism of ion conduction in PEO/LiBF4 near TiO2 surfaces compared to the bulk PEO/LiBF4.

  20. Impedance studies of a green blend polymer electrolyte based on PVA and Aloe-vera

    Science.gov (United States)

    Selvalakshmi, S.; Mathavan, T.; Vijaya, N.; Selvasekarapandian, Premalatha, M.; Monisha, S.

    2016-05-01

    The development of polymer electrolyte materials for energy generating and energy storage devices is a challenge today. A new type of blended green electrolyte based on Poly-vinyl alcohol (PVA) and Aloe-vera has been prepared by solution casting technique. The blending of polymers may lead to the increase in stability due to one polymer portraying itself as a mechanical stiffener and the other as a gelled matrix supported by the other. The prepared blend electrolytes were subjected to Ac impedance studies. It has been found out that the polymer film in which 1 gm of PVA was dissolved in 40 ml of Aloe-vera extract exhibits highest conductivity and its value is 3.08 × 10-4 S cm-1.

  1. A quasi-direct methanol fuel cell system based on blend polymer membrane electrolytes

    DEFF Research Database (Denmark)

    Li, Qingfeng; Hjuler, Hans Aage; Hasiotis, C.

    2002-01-01

    , compared to less than 100 ppm CO for the Nafion-based technology at 80degrees C. The high CO tolerance makes it possible to use the reformed hydrogen directly from a simple methanol reformer without further CO removal. That both the fuel cell and the methanol reformer operate at temperatures around 200......On the basis of blend polymer electrolytes of polybenzimidazole and sulfonated polysulfone, a polymer electrolyte membrane fuel cell was developed with an operational temperature up to 200degrees C. Due to the high operational temperature, the fuel cell can tolerate 1.0-3.0 vol % CO in the fuel...

  2. Instability of Ionic Liquid-Based Electrolytes in Li−O2 Batteries

    DEFF Research Database (Denmark)

    Das, Supti; Højberg, Jonathan; Knudsen, Kristian Bastholm

    2015-01-01

    Ionic liquids (ILs) have been proposed as promising solvents for Li−air battery electrolytes. Here, several ILs have been investigated using differential electrochemical mass spectrometry (DEMS) to investigate the electrochemical stability in a Li−O2 system, by means of quantitative determination...... of the rechargeability (OER/ORR), and thereby the Coulombic efficiency of discharge and charge. None of the IL-based electrolytes are found to behave as needed for a functional Li−O2 battery but perform better than commonly used organic solvents. Also the extent of rechargeability/reversibility has been found...

  3. New halogenated additives to propylene carbonate-based electrolytes for lithium-ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Naji, A.; Ghanbaja, J.; Billaud, D. [Universite Henri Poincare, Vandoeuvre les Nancy (France). LCSM; Willmann, P. [CNES, Toulouse (France)

    2000-07-01

    Lithium cannot be electrointercalated into graphite in an electrolyte containing propylene carbonate (PC) as the only solvent species. In order to improve the cyclability of graphite electrodes in the presence of PC two methods were used: use of solvent mixtures containing PC and halogen-substituted solvent molecules ({alpha}-bromo-{gamma}-butyrolactone and methyl chloroformate); impregnation of the graphite electrode by halogenated solvents prior to cycling in PC-based electrolytes. It appears that the reversible capacity is increased by {approx}10% when such halogenated solvent molecules are used. Moreover, the cyclability is dependent on the nature of lithium salt, the concentration of halogen solvent and the specific current.

  4. [Synthesis and Characterization of a Sugar Based Electrolyte for Thin-film Polymer Batteries

    Science.gov (United States)

    1998-01-01

    The work performed during the current renewal period, March 1,1998 focused primarily on the synthesis and characterization of a sugar based electrolyte for thin-film polymer batteries. The initial phase of the project involved developing a suitable sugar to use as the monomer in the polymeric electrolyte synthesis. The monomer has been synthesized and characterized completely. Overall the yield of this material is high and it can be produced in relatively large quantity easily and in high purity. The scheme used for the preparation of the monomer is outlined along with pertinent yields.

  5. Sol-gel based sensor for selective formaldehyde determination.

    Science.gov (United States)

    Bunkoed, Opas; Davis, Frank; Kanatharana, Proespichaya; Thavarungkul, Panote; Higson, Séamus P J

    2010-02-01

    We report the development of transparent sol-gels with entrapped sensitive and selective reagents for the detection of formaldehyde. The sampling method is based on the adsorption of formaldehyde from the air and reaction with beta-diketones (for example acetylacetone) in a sol-gel matrix to produce a yellow product, lutidine, which was detected directly. The proposed method does not require preparation of samples prior to analysis and allows both screening by visual detection and quantitative measurement by simple spectrophotometry. The detection limit of 0.03 ppmv formaldehyde is reported which is lower than the maximum exposure concentrations recommended by both the World Health Organisation (WHO) and the Occupational Safety and Health Administration (OSHA). This sampling method was found to give good reproducibility, the relative standard deviation at 0.2 and 1 ppmv being 6.3% and 4.6%, respectively. Other carbonyl compounds i.e. acetaldehyde, benzaldehyde, acetone and butanone do not interfere with this analytical approach. Results are provided for the determination of formaldehyde in indoor air.

  6. 聚合物锂离子蓄电池用凝胶聚合物电解质%Gel polymeric electrolytes for polymer lithium-ion battery

    Institute of Scientific and Technical Information of China (English)

    汪国杰; 周震涛; 潘慧铭

    2001-01-01

    Polymer and plasticizer were two main components of gel polymeric electrolyte(GPE)for polymer lithi-um-ion battery, and the components structure and properties of GPE were introduced in details. Attention wasdevoted to reviewing the structure of components, interactions among them and how these factors affected the properties of GPE. Three methods for improving mechanical properties of GPE were reviewed-cross-linking, adding filler and using structure with two phases. Finally, introduced the main properties, current development and tendency of plastic Li-ion battery composed of GPE.%较详细地介绍了聚合物锂离子蓄电池用凝胶聚合物电解质的两种主要组成:聚合物和增塑剂,着重阐述了其各组分的结构和组分间相互作用对其性能的影响。综述了凝胶聚合物电解质的几个主要性能--离子传递性能,电化学稳定性,热稳定性和力学性能等,以及影响其有关性能的结构因素。还详述了改善凝胶聚合物电解质力学性能的三种方法:交联,添加填料和采用两相结构。最后介绍了由其制备的聚合物锂离子电池的性能、特点、研制现状和前景展望。

  7. Synthesis and characterization of CuO nanoparticles using strong base electrolyte through electrochemical discharge process

    Indian Academy of Sciences (India)

    PURUSHOTTAM KUMAR SINGH; PANKAJ KUMAR; MANOWAR HUSSAIN; ALOK KUMAR DAS; GANESH CHANDRA NAYAK

    2016-04-01

    In the present study, cupric oxide (CuO) nanoparticles were synthesized by electrochemical discharge process using strong base electrolytes. The experiments were carried out separately using NaOH and KOH electrolytes.The mass output rate and the crystal size were obtained with variation of the rotation speed of magnetic stirrer for both types of electrolytes. The mass output rate of CuO nanoparticles increased with the increase in the speed of rotation, and, after an optimum speed, it started decreasing. However, the size of the particles reduced with the increase of the rotation speed. The crystal plane of the obtained CuO nanoparticles was similar for both the electrolytes whereas the yield of nanoparticles was higher in KOH as compared with NaOH under the sameexperiment conditions. In this set of experiments, the maximum output rates obtained were 21.66 mg h$^{−1}$ for NaOH and 24.66 mg h$^{−1}$ for KOH at 200 rpm for a single discharge arrangement. The average crystal size of CuO particles obtained was in the range of 13–18 nm for KOH electrolyte and 15–20 nm for NaOH electrolyte. Scanning electron microscopy images revealed that flower-like and caddice clew-shaped CuO nanocrystalline particles weresynthesized by the electrochemical discharge process. Fourier transform infrared spectrum showed that the CuO nanoparticles have a pure and monolithic phase. UV–vis–NIR spectroscopy was used to monitor oxidation course of Cu→CuO and the band gap energy was measured as 2 and 2.6 eV for CuO nanoparticle synthesized in NaOH and KOH solutions, respectively.

  8. Zinc ion conducting polymer electrolytes based on oligomeric polyether/PVDF-HFP blends

    Science.gov (United States)

    Ye, Hui; Xu, Jun John

    Here we report novel zinc ion conducting polymer electrolytes based on oligomeric polyether/PVDF-HFP blends with or without the incorporation of a small amount of organic carbonates. Their thermal properties, ionic conductivity and electrochemical properties are characterized and the effect of different Zn salts and incorporation of a small amount of organic carbonates are investigated. These polymer electrolyte membranes exhibit essentially no or very low volatility, high thermal stability, high ionic conductivity, wide electrochemical stability window, acceptable interfacial resistance with zinc, and the capability for reversible Zn plating/stripping. Particularly promising are electrolyte systems based on the combination of low lattice energy zinc imide salt and a special co-solvent of oligomeric poly(ethylene glycol) dimethyl ether (PEGDME) mixed with a small amount of ethylene carbonate (EC), dimensionally stabilized with PVDF-HFP. Such novel polymer electrolyte membranes could lead to the development of new kinds of electrochemical energy storage devices based on zinc electrochemistry, including solid-state, thin-film rechargeable zinc/air cells envisaged.

  9. Zinc ion conducting polymer electrolytes based on oligomeric polyether/PVDF-HFP blends

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Hui; Xu, Jun John [Department of Materials Science and Engineering, Rutgers, the State University of New Jersey, Piscataway, NJ 08854 (United States)

    2007-03-20

    Here we report novel zinc ion conducting polymer electrolytes based on oligomeric polyether/PVDF-HFP blends with or without the incorporation of a small amount of organic carbonates. Their thermal properties, ionic conductivity and electrochemical properties are characterized and the effect of different Zn salts and incorporation of a small amount of organic carbonates are investigated. These polymer electrolyte membranes exhibit essentially no or very low volatility, high thermal stability, high ionic conductivity, wide electrochemical stability window, acceptable interfacial resistance with zinc, and the capability for reversible Zn plating/stripping. Particularly promising are electrolyte systems based on the combination of low lattice energy zinc imide salt and a special co-solvent of oligomeric poly(ethylene glycol) dimethyl ether (PEGDME) mixed with a small amount of ethylene carbonate (EC), dimensionally stabilized with PVDF-HFP. Such novel polymer electrolyte membranes could lead to the development of new kinds of electrochemical energy storage devices based on zinc electrochemistry, including solid-state, thin-film rechargeable zinc/air cells envisaged. (author)

  10. Flexible thin-film battery based on solid-like ionic liquid-polymer electrolyte

    Science.gov (United States)

    Li, Qin; Ardebili, Haleh

    2016-01-01

    The development of high-performance flexible batteries is imperative for several contemporary applications including flexible electronics, wearable sensors and implantable medical devices. However, traditional organic liquid-based electrolytes are not ideal for flexible batteries due to their inherent safety and stability issues. In this study, a non-volatile, non-flammable and safe ionic liquid (IL)-based polymer electrolyte film with solid-like feature is fabricated and incorporated in a flexible lithium ion battery. The ionic liquid is 1-Ethyl-3-methylimidazolium dicyanamide (EMIMDCA) and the polymer is composed of poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-HFP). The electrolyte exhibits good thermal stability (i.e. no weight loss up to 300 °C) and relatively high ionic conductivity (6 × 10-4 S cm-1). The flexible thin-film lithium ion battery based on solid-like electrolyte film is encapsulated using a thermal-lamination process and demonstrates excellent electrochemical performance, in both flat and bent configurations.

  11. Acid-base and electrolyte disorders in patients with diabetes mellitus.

    Science.gov (United States)

    Sotirakopoulos, Nikolaos; Kalogiannidou, Irini; Tersi, Maria; Armentzioiou, Karmen; Sivridis, Dimitrios; Mavromatidis, Konstantinos

    2012-01-01

    Diabetes mellitus is the most common metabolic disorder in the community. The diabetics may suffer from acid-base and electrolyte disorders due to complications of diabetes mellitus and the medication they receive. In this study, acid-base and electrolyte disorders were evaluated among outpatient diabetics in our hospital. The study consisted of patients with diabetes mellitus who visited the hospital as outpatients between the period January 1, 2004 to December 31, 2006. The patients' medical history, age and type of diabetes were noted, including whether they were taking diuretics and calcium channel blockers or not. Serum creatinine, proteins, sodium, potassium and chloride and blood gases were measured in all patients. Proteinuria was measured by 24-h urine collection. Two hundred and ten patients were divided in three groups based on the serum creatinine. Group A consisted of 114 patients that had serum creatinine 3.1 mg/dL. Of the 210 patients, 176 had an acid-base disorder. The most common disorder noted in group A was metabolic alkalosis. In groups B and C, the common disorders were metabolic acidosis and alkalosis, and metabolic acidosis, respectively. The most common electrolyte disorders were hypernatremia (especially in groups A and B), hyponatremia (group C) and hyperkalemia (especially in groups B and C). It is concluded that: (a) in diabetic outpatients, acid-base and electrolyte disorders occurred often even if the renal function is normal, (b) the most common disorders are metabolic alkalosis and metabolic acidosis (the frequency increases with the deterioration of the renal function) and (c) the common electrolyte disorders are hypernatremia and hypokalemia.

  12. Acid-base and electrolyte disorders in patients with diabetes mellitus

    Directory of Open Access Journals (Sweden)

    Nikolaos Sotirakopoulos

    2012-01-01

    Full Text Available Diabetes mellitus is the most common metabolic disorder in the community. The diabetics may suffer from acid-base and electrolyte disorders due to complications of diabetes mellitus and the medication they receive. In this study, acid-base and electrolyte disorders were evaluated among outpatient diabetics in our hospital. The study consisted of patients with diabetes mellitus who visited the hospital as outpatients between the period January 1, 2004 to December 31, 2006. The patients′ medical history, age and type of diabetes were noted, including whether they were taking diuretics and calcium channel blockers or not. Serum creatinine, proteins, sodium, potassium and chloride and blood gases were measured in all patients. Proteinuria was measured by 24-h urine collection. Two hundred and ten patients were divided in three groups based on the serum creatinine. Group A consisted of 114 patients that had serum creatinine 3.1 mg/dL. Of the 210 patients, 176 had an acid-base disorder. The most common disorder noted in group A was metabolic alkalosis. In groups B and C, the common disorders were metabolic acidosis and alkalosis, and metabolic acidosis, respectively. The most common electrolyte disorders were hypernatremia (especially in groups A and B, hyponatremia (group C and hyperkalemia (especially in groups B and C. It is concluded that: (a in diabetic outpatients, acid-base and electrolyte disorders occurred often even if the renal function is normal, (b the most common disorders are metabolic alkalosis and metabolic acidosis (the frequency increases with the deterioration of the renal function and (c the common electrolyte disorders are hypernatremia and hypokalemia.

  13. Creation of Functional Organic Gels Based on Oligothiophenes

    Institute of Scientific and Technical Information of China (English)

    Liu Ping; Zhao Qi-zhong; Hu Jian-hua; Zhou Xiao-ping; Deng Wen-ji; Xu Yun-hua

    2004-01-01

    Polymer gels have received a great deal of attention not only from scientific interest but also for their practical applications. Recently, low molecular-weight organic gels have also been receiving growing attention. However, their have been few studies of low molecular-weight organic gels in contrast to extensive studies of polymer gels.In order to develop a novel class of low-molecular-weight organic gels and to gain an insight into the relationship between molecular structures of gel-forming compounds and gel-forming properties, a novel family of low molecular-weight organic compounds containing oligothiophene,N,N'-distearyl-5,5"-(2,2':5',2"-terthiophe-ne)dicarboxamide(DNC183T),N,N'-dialkyl-5,5"-(3,3"-dioctyl-2,2':5',2"-terthiophene)dicarboxamide(DNCnDOc3T, n = 5, 8, 16, 18)and N,N'-distearyl-5,5'"-( 3,3'"-dioctyl- 2,2':5',2 ":5",2'"-quaterthiophene)dicarboxamide(DNC1sDOc4T), were designed and synthesized. Whereas DNC183T did not form gels with organic solvents, DNCnDOc3T(n = 8, 16, 18) and DNC18DOc4T were found to form gels with certain organic solvents. These are the first examples of low molecular-weight organic gels containing an oligothiophene moiety. It is of intest to note that while DNC8DOc3T forms opaque gels with alcohols,e.g. ethanol and isopropanol, DNC16DOc3T, DNC18DOc3T and DNC18DOc4Tform transparent gels with hydrocarbon solvents such as heptane, octane, undecane, and others. It is shown that the intermolecular hydrogen bonding and intermolecular interactions between the long alkyl chain in the N-alkylcarboxamide group as well as the incorporation of an alkyl group at the β-position of the thiophene ring play an important role for the formation of gels. The optical micrographs of gels and the SEM images of xerogels showed three-dimensional networks of fibrous bundle structures.DNC18DOc4T gels was found to exhibit a reversible clear color change on electrochemical oxidation and reduction. Thus, low molecular-weight organic gels function as a new

  14. High Impulse Nanoparticulate-Based Gel Propellants Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposed Small Business Innovative Research (SBIR) Phase I addresses the development of advanced gel propellants and determination of their suitability for...

  15. Development on In-situ Synthesis of Gel Polymer Electrolyte for Lithium Batteries%现场聚合制备锂离子电池用凝胶聚合物电解质研究进展

    Institute of Scientific and Technical Information of China (English)

    范欢欢; 周栋; 范丽珍; 石桥

    2013-01-01

    Lithium-ion batteries with a high energy density are developed for future energy storage devices. Recent works focus on gel polymer electrolyte with easily shaped properties due to its effective solution to the security problem caused by liquid electrolyte leakage. This paper reviews the in-situ polymerization technology, which has increasingly attractive attentions in the preparation process of gel polymer electrolyte. Moreover, this paper represents the reaction principle, process route and influencing factors on the product performance in some detail, and also prospects the in-situ polymerization process development as a promising lithium-ion battery production technology.%高比能量锂离子电池是未来储能器件的发展方向.凝胶聚合物锂离子电池因易于加工并克服了以往液态锂离子电池因漏液而造成的安全性问题,成为近年来的研究热点.综述了目前凝胶聚合物电解质制备工艺中最受关注的现场聚合技术,介绍了反应原理、工艺路线、成品性能等,并展望了现场聚合工艺作为新兴锂离子电池生产技术的发展趋势.

  16. The study of electrical conductivity and diffusion behavior of water-based and ferro/ferricyanide-electrolyte-based alumina nanofluids.

    Science.gov (United States)

    Liu, Chang; Lee, Hyeonseok; Chang, Ya-Huei; Feng, Shien-Ping

    2016-05-01

    Nanofluids are liquids containing suspensions of solid nanoparticles and have attracted considerable attention because they undergo substantial mass transfer and have many potential applications in energy technologies. Most studies on nanofluids have used low-ionic-strength solutions, such as water and ethanol. However, very few studies have used high-ionic-strength solutions because the aggregation and sedimentation of nanoparticles cause a stability problem. In this study, a stable water-based alumina nanofluid was prepared using stirred bead milling and exhibits a high electrical conductivity of 2420 μS/cm at 23 °C and excellent stability after five severe freezing-melting cycles. We then developed a process for mixing the water-based nanofluid with a high-ionic-strength potassium ferro/ferricyanide electrolyte and sodium dodecyl sulfate by using stirred bead milling and ultrasonication, thus forming a stable electrolyte-based nanofluid. According to the rotating disk electrode study, the electrolyte-based alumina nanofluid exhibits an unusual increase in the limiting current at high angular velocities, resulting from a combination of local percolation behavior and shear-induced diffusion. The electrolyte-based alumina nanofluid was demonstrated in a possible thermogalvanic application, since it is considered to be an alternative electrolyte for thermal energy harvesters because of the increased electrical conductivity and confined value of thermal conductivity.

  17. A fuel cell operating between room temperature and 250 C based on a new phosphoric acid based composite electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Lan, Rong [Department of Chemistry, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); Xu, Xiaoxiang; Irvine, John T.S. [School of Chemistry, University of St Andrews, St Andrews, Fife KY16 9ST (United Kingdom); Tao, Shanwen [Department of Chemistry, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom); School of Chemistry, University of St Andrews, St Andrews, Fife KY16 9ST (United Kingdom)

    2010-10-15

    A phosphoric acid based composite material with core-shell microstructure has been developed to be used as a new electrolyte for fuel cells. A fuel cell based on this electrolyte can operate at room temperature indicating leaching of H{sub 3}PO{sub 4} with liquid water is insignificant at room temperature. This will help to improve the thermal cyclability of phosphoric acid based electrolyte to make it easier for practical use. The conductivity of this H{sub 3}PO{sub 4}-based electrolyte is stable at 250 C with addition of the hydrophilic inorganic compound BPO{sub 4} forming a core-shell microstructure which makes it possible to run a PAFC at a temperature above 200 C. The core-shell microstructure retains after the fuel cell measurements. A power density of 350 mW/cm{sup 2} for a H{sub 2}/O{sub 2} fuel cell has been achieved at 200 C. The increase in operating temperature does not have significant benefit to the performance of a H{sub 2}/O{sub 2} fuel cell. For the first time, a composite electrolyte material for phosphoric acid fuel cells which can operate in a wide range of temperature has been evaluated but certainly further investigation is required. (author)

  18. Methyl phosphate formation as a major degradation mode of direct methanol fuel cells with phosphoric acid based electrolytes

    DEFF Research Database (Denmark)

    Aili, David; Vassiliev, Anton; Jensen, Jens Oluf

    2015-01-01

    Phosphoric acid and phosphoric acid doped polymer membranes are widely used as electrolytes in hydrogen based fuel cells operating at elevated temperatures. Such electrolytes have been explored for direct oxidation of methanol to further increase the versatility of the systems, however, with demo...

  19. Microstructure, rheological and wound healing properties of collagen-based gel from cuttlefish skin.

    Science.gov (United States)

    Jridi, Mourad; Bardaa, Sana; Moalla, Dorsaf; Rebaii, Tarak; Souissi, Nabil; Sahnoun, Zouheir; Nasri, Moncef

    2015-01-01

    Collagen-based biomaterials are of the utmost importance for tissue engineering and regenerative medicine. The aims of the present investigation were to evaluate structural and rheological properties of collagen-based gel obtained from cuttlefish skin, and to investigate its ability to enhance wound healing. Scanning electron microscopy of resulted gel showed a dense fibrillar microstructure with high interconnection network with a smaller pore size. In addition, the rheological characterization of collagen gel showed an excellent reversibility, when subjected to a temperature variation. Moreover, in the wound-healing study, topical application of collagen based gel increased significantly the percentage of wound closure over a period of 12 days, when compared to the untreated and CICAFLORA(®)-treated groups. Wound-healing activity of collagen gel was confirmed by histopathology study. Thus, cuttlefish collagen based gel might be useful as a wound healing agent.

  20. A high performance flexible all solid state supercapacitor based on the MnO2 sphere coated macro/mesoporous Ni/C electrode and ionic conducting electrolyte

    Science.gov (United States)

    Zhi, Jian; Reiser, Oliver; Wang, Youfu; Hu, Aiguo

    2016-06-01

    A high contact resistance between the active materials and the current collector, a low ionic conductivity of the gel electrolyte, and an impenetrable electrode structure are the three major barriers which greatly limit the capacitance of MnO2 in solid state supercapacitors. As a potential solution to these problems, in this work we report a novel electrode for solid state supercapacitors, based on a ternary system composed of hierarchical MnO2 spheres as the active material, macroporous Ni foam as gel penetrable skeletons and an ordered mesoporous carbon (OMC) membrane as the charge-transport accelerating layer. By employing butyl-3-methylimidazolium chloride (BMIMCl) modified gels as the ionic conducting electrolyte, the utilization efficiency of MnO2 on the specific capacitance was enhanced up to 88% of the theoretical value, delivering a volumetric capacitance of 81 F cm-3, which is the highest value among MnO2 based solid state supercapacitors. Moreover, such a flexible device exhibits exceptional volumetric energy and power density (6.6 Wh L-1 and 549 W L-1, based on the whole device volume) combined with a small capacity loss of 8.5% after 6000 cycles under twisting. These encouraging findings unambiguously overcome the energy bottleneck of MnO2 in solid state supercapacitors, and open up a new application of macro/mesoporous materials in flexible devices.A high contact resistance between the active materials and the current collector, a low ionic conductivity of the gel electrolyte, and an impenetrable electrode structure are the three major barriers which greatly limit the capacitance of MnO2 in solid state supercapacitors. As a potential solution to these problems, in this work we report a novel electrode for solid state supercapacitors, based on a ternary system composed of hierarchical MnO2 spheres as the active material, macroporous Ni foam as gel penetrable skeletons and an ordered mesoporous carbon (OMC) membrane as the charge-transport accelerating

  1. Preparation of tamarind gum based soft ion gels having thixotropic properties.

    Science.gov (United States)

    Sharma, Mukesh; Mondal, Dibyendu; Mukesh, Chandrakant; Prasad, Kamalesh

    2014-02-15

    Tamarind gum was used to prepare ion gels using both synthetic ionic liquids (ILs) namely 1-butyl-3-methylimidazolium chloride and 1-butyl-3-methylimidazolium bromide and bio-based ionic liquids (Bio-ILs) namely choline acrylate, choline caproate and choline caprylate by heating cooling process. The gels were found to have good thermal stability and exhibited thixotropic behaviour. Upon relaxation after applied breaking strain, the recovery of gel structures after ten consecutive cycles was observed. The hydrogel of the gum prepared using ethanol aqueous solution had much inferior quality in terms of viscosity, viscoelasticity, thermal stability and thixotropicity when compared with the ion gels. The ion gels also showed very good adherence to human finger muscles and skin. The ion gels thus prepared may find application in electrochemistry, sensors, actuators and the gels prepared with Bio-ILs could even be useful in biomedical applications.

  2. Preparation of novel carbon microfiber/carbon nanofiber-dispersed polyvinyl alcohol-based nanocomposite material for lithium-ion electrolyte battery separator.

    Science.gov (United States)

    Sharma, Ajit K; Khare, Prateek; Singh, Jayant K; Verma, Nishith

    2013-04-01

    A novel nanocomposite polyvinyl alcohol precursor-based material dispersed with the web of carbon microfibers and carbon nanofibers is developed as lithium (Li)-ion electrolyte battery separator. The primary synthesis steps of the separator material consist of esterification of polyvinyl acetate to produce polyvinyl alcohol gel, ball-milling of the surfactant dispersed carbon micro-nanofibers, mixing of the milled micron size (~500 nm) fibers to the reactant mixture at the incipience of the polyvinyl alcohol gel formation, and the mixing of hydrophobic reagents along with polyethylene glycol as a plasticizer, to produce a thin film of ~25 μm. The produced film, uniformly dispersed with carbon micro-nanofibers, has dramatically improved performance as a battery separator, with the ion conductivity of the electrolytes (LiPF6) saturated film measured as 0.119 S-cm(-1), approximately two orders of magnitude higher than that of polyvinyl alcohol. The other primary characteristics of the produced film, such as tensile strength, contact angle, and thermal stability, are also found to be superior to the materials made of other precursors, including polypropylene and polyethylene, discussed in the literature. The method of producing the films in this study is novel, simple, environmentally benign, and economically viable.

  3. Nanoporous Hybrid Electrolytes for High-Energy Batteries Based on Reactive Metal Anodes

    KAUST Repository

    Tu, Zhengyuan

    2017-01-06

    Successful strategies for stabilizing electrodeposition of reactive metals, including lithium, sodium, and aluminum are a requirement for safe, high-energy electrochemical storage technologies that utilize these metals as anodes. Unstable deposition produces high-surface area dendritic structures at the anode/electrolyte interface, which causes premature cell failure by complex physical and chemical processes that have presented formidable barriers to progress. Here, it is reported that hybrid electrolytes created by infusing conventional liquid electrolytes into nanoporous membranes provide exceptional ability to stabilize Li. Electrochemical cells based on γ-Al2O3 ceramics with pore diameters below a cut-off value above 200 nm exhibit long-term stability even at a current density of 3 mA cm−2. The effect is not limited to ceramics; similar large enhancements in stability are observed for polypropylene membranes with less monodisperse pores below 450 nm. These findings are critically assessed using theories for ion rectification and electrodeposition reactions in porous solids and show that the source of stable electrodeposition in nanoporous electrolytes is fundamental.

  4. Molar conductivity calculation of Li-ion battery electrolyte based on mode coupling theory

    Science.gov (United States)

    Pu, Weihua; He, Xiangming; Lu, Jiufang; Jiang, Changyin; Wan, Chunrong

    2005-12-01

    A method is proposed to calculate molar conductivity based on mode coupling theory in which the ion transference number is introduced into the theory. The molar conductivities of LiPF6, LiClO4, LiBF4, LiAsF6 in PC (propylene carbonate) are calculated based on this method. The results fit well to the literature data. This presents a potential way to calculate the conductivities of Li-ion battery electrolytes.

  5. Electrolyte and Acid-Base Disturbances in End-Stage Liver Disease: A Physiopathological Approach.

    Science.gov (United States)

    Jiménez, José Víctor; Carrillo-Pérez, Diego Luis; Rosado-Canto, Rodrigo; García-Juárez, Ignacio; Torre, Aldo; Kershenobich, David; Carrillo-Maravilla, Eduardo

    2017-08-01

    Electrolyte and acid-base disturbances are frequent in patients with end-stage liver disease; the underlying physiopathological mechanisms are often complex and represent a diagnostic and therapeutic challenge to the physician. Usually, these disorders do not develop in compensated cirrhotic patients, but with the onset of the classic complications of cirrhosis such as ascites, renal failure, spontaneous bacterial peritonitis and variceal bleeding, multiple electrolyte, and acid-base disturbances emerge. Hyponatremia parallels ascites formation and is a well-known trigger of hepatic encephalopathy; its management in this particular population poses a risky challenge due to the high susceptibility of cirrhotic patients to osmotic demyelination. Hypokalemia is common in the setting of cirrhosis: multiple potassium wasting mechanisms both inherent to the disease and resulting from its management make these patients particularly susceptible to potassium depletion even in the setting of normokalemia. Acid-base disturbances range from classical respiratory alkalosis to high anion gap metabolic acidosis, almost comprising the full acid-base spectrum. Because most electrolyte and acid-base disturbances are managed in terms of their underlying trigger factors, a systematic physiopathological approach to their diagnosis and treatment is required.

  6. Non-flammable electrolytes based on trimethyl phosphate solvent for lithium-ion batteries

    Institute of Scientific and Technical Information of China (English)

    HU Chuan-yue; LI Xin-hai

    2005-01-01

    The properties of trimethyl phosphate(TMP)-based nonflammable electrolytes with LiPF6 as solute were investigated using graphite anode and LiCoO2 cathode. The effect of TMP on non-flammability of electrolytes was also evaluated. It is found that the TMP reduction decomposition on graphite electrode at the potential of 1.3V (vs Li/Li+) is suppressed with ethylene carbonate(EC), dimethyl carbonate(DMC) and ethylmethyl carbonate(EMC) cosolvents and vinylene carbonate(VC) additives. The results show that the non-flammable electrolyte of 1mol/L LiPF6 61%(EC1.5-DMC1.0-EMC1.0)-39% TMP has good electrochemical properties. The discharge capacities of half-cells after 20 cycles are 254.8mA·h/g for Li/graphite and 144.1mA·h/g for Li/LiCoO2. The graphite/LiCoO2 prismatic lithium-ion cell delivers a discharge capacity of 131mA·h/g at first cycle. With an addition of 4%VC to this non-flammable electrolyte, a discharge capacity of 134mA·h/g at first cycle and a capacity ratio of 84.3% after 50 cycles are obtained for prismatic lithium-ion batteries. Furthermore, a nail penetration test demonstrates that the safety of prismatic lithium-ion batteries is dramatically improved by using TMP-containing non-flammable electrolytes.

  7. 3 V omni-directionally stretchable one-body supercapacitors based on a single ion-gel matrix and carbon nanotubes

    Science.gov (United States)

    Kim, Wonbin; Kim, Woong

    2016-06-01

    Stretchable supercapacitors often have laminated structures consisting of electrode, electrolyte, and supporting layers. Since the layers are likely to be composed of different materials, delamination is a major cause of failure upon stretching. In this study, we demonstrate delamination-free stretchable supercapacitors where all the component layers are prepared with a single matrix, which is composed of a polymer, poly(vinylidene fluoride-hexafluoropropylene) and an ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide. Since the ionic liquid in the composite plays a role as both an electrolyte and a plasticizer, this composite can be used as an electrolyte and a supporting layer in the stretchable supercapacitor. The electrode layer can be fabricated by incorporating carbon nanotubes in the common matrix. Then, all the layers can be seamlessly fused into one body by dissolving the surface of the composite with acetone, which evaporates after the integration, leaving no borders between the layers. This one-body stretchable supercapacitor not only has high durability against repetitive stretches but also is stretchable in all directions. This feature clearly distinguishes them from conventional stretchable supercapacitors fabricated using buckled structures, which are stretchable only in one or two directions. Moreover, this supercapacitor has high cell voltage (˜3 V) owing to the ionic liquid-based gel electrolytes. Our demonstration of isotropically stretchable high-durability supercapacitors may have a great implication in the development of stretchable energy storage devices for real applications.

  8. Iron-based cathode catalyst with enhanced power density in polymer electrolyte membrane fuel cells.

    Science.gov (United States)

    Proietti, Eric; Jaouen, Frédéric; Lefèvre, Michel; Larouche, Nicholas; Tian, Juan; Herranz, Juan; Dodelet, Jean-Pol

    2011-08-02

    H(2)-air polymer-electrolyte-membrane fuel cells are electrochemical power generators with potential vehicle propulsion applications. To help reduce their cost and encourage widespread use, research has focused on replacing the expensive Pt-based electrocatalysts in polymer-electrolyte-membrane fuel cells with a lower-cost alternative. Fe-based cathode catalysts are promising contenders, but their power density has been low compared with Pt-based cathodes, largely due to poor mass-transport properties. Here we report an iron-acetate/phenanthroline/zeolitic-imidazolate-framework-derived electrocatalyst with increased volumetric activity and enhanced mass-transport properties. The zeolitic-imidazolate-framework serves as a microporous host for phenanthroline and ferrous acetate to form a catalyst precursor that is subsequently heat treated. A cathode made with the best electrocatalyst from this work, tested in H(2)-O(2,) has a power density of 0.75 W cm(-2) at 0.6 V, a meaningful voltage for polymer-electrolyte-membrane fuel cells operation, comparable with that of a commercial Pt-based cathode tested under identical conditions.

  9. Elucidating the Higher Stability of Vanadium (V) Cations in Mixed Acid Based Redox Flow Battery Electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Vijayakumar, M.; Wang, Wei; Nie, Zimin; Sprenkle, Vincent L.; Hu, Jian Z.

    2013-11-01

    The Vanadium (V) cation structures in mixed acid based electrolyte solution were analysed by density functional theory (DFT) based computational modelling and 51V and 35Cl Nuclear Magnetic Resonance (NMR) spectroscopy. The Vanadium (V) cation exists as di-nuclear [V2O3Cl2.6H2O]2+ compound at higher vanadium concentrations (≥1.75M). In particular, at high temperatures (>295K) this di-nuclear compound undergoes ligand exchange process with nearby solvent chlorine molecule and forms chlorine bonded [V2O3Cl2.6H2O]2+ compound. This chlorine bonded [V2O3Cl2.6H2O]2+ compound might be resistant to the de-protonation reaction which is the initial step in the precipitation reaction in Vanadium based electrolyte solutions. The combined theoretical and experimental approach reveals that formation of chlorine bonded [V2O3Cl2.6H2O]2+ compound might be central to the observed higher thermal stability of mixed acid based Vanadium (V) electrolyte solutions.

  10. Chemical Sensors Based on Molecularly Imprinted Sol-Gel Materials

    OpenAIRE

    Dickert, Franz L.; Lieberzeit, Peter A.; Adnan Mujahid

    2010-01-01

    The sol-gel technique is earning the worldwide attention of researchers in the field of material science, due to its versatility in synthesizing inorganic ceramic materials at mild conditions. High purity, homogeneity, controlled porosity, stable temperature and nanoscale structuring are the most remarkable features offered by this method for generating highly sensitive and selective matrices to incorporate analyte molecules. The crafting of sol-gel sensors through molecular imprinting has pu...

  11. Xyloglucan Based In Situ Gel of Lidocaine HCl for the Treatment of Periodontosis

    OpenAIRE

    Pandit, Ashlesha P.; Vaibhav V. Pol; Kulkarni, Vinit S.

    2016-01-01

    The present study was aimed at formulating thermoreversible in situ gel of local anesthetic by using xyloglucan based mucoadhesive tamarind seed polysaccharide (TSP) into periodontal pocket. Temperature-sensitive in situ gel of lidocaine hydrochloride (LH) (2% w/v) was formulated by cold method. A full 32 factorial design was employed to study the effect of independent variables concentrations of Lutrol F127 and TSP to optimize in situ gel. The dependent variables evaluated were gelation temp...

  12. Effective solid electrolyte based on benzothiazolium for dye-sensitized solar cells.

    Science.gov (United States)

    Han, Lu; Wang, Ye Feng; Zeng, Jing Hui

    2014-12-24

    Thiaozole/benzothiaozole-based dicationic conductors were synthesized and applied as solid-state electrolyte in dye-sensitized solar cells (DSSCs). X-ray diffraction, scanning electron microscopy, thermal gravimetric analysis, steady-state voltammogram, photocurrent intensity-photovoltage test, and electrochemical impedance spectroscopy are used to characterize the materials and the mechanism of the cell performance. Compared to the traditional monocationic crystals, the dicationic crystals have a larger size and can provide more opportunities to fine-tune their physical/chemical properties. As a consequence, this solid-state electrolyte-based DSSC achieved photoelectric conversion efficiency of 7.90% under full air-mass (AM 1.5) sunlight (100 mW·cm(-2)).

  13. Alternative Single-Solvent Electrolytes Based on Cyanoesters for Safer Lithium-Ion Batteries.

    Science.gov (United States)

    Brox, Sebastian; Röser, Stephan; Husch, Tamara; Hildebrand, Stephan; Fromm, Olga; Korth, Martin; Winter, Martin; Cekic-Laskovic, Isidora

    2016-07-07

    To identify alternative single-solvent-based electrolytes for application in lithium-ion batteries (LIBs), adequate computational methods were applied to screen specified physicochemical and electrochemical properties of new cyanoester-based compounds. Out of 2747 possible target compounds, two promising candidates and two structurally equivalent components were chosen. A constructive selection process including evaluation of basic physicochemical properties as well assessing the compatibility towards graphitic anodes was initiated to identify the most promising candidates. With addition of a film-forming additive in a low concentration, the most promising candidate showed an adequate long-term cycling stability with LiNi1/3 Mn1/3 Co1/3 O2 [NMC(111)] in a full-cell setup using graphite as anode material. The main advantages of the new electrolyte formulation are related to its good thermal behavior, especially with regard to safety in combination with satisfying electrochemical performance.

  14. Characterization of ι-carrageenan and its derivative based green polymer electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Jumaah, Fatihah Najirah; Mobaraka, Nadhratun Naiim; Ahmad, Azizan; Ramli, Nazaruddin [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600, Bangi, Selangor Darul Ehsan (Malaysia)

    2013-11-27

    The new types of green polymer electrolytes based on ι-carrageenan derivative have been prepared. ι-carrageenan act as precursor was reacted with monochloroacetic acid to produce carboxymethyl ι-carrageenan. The powders were characterized by Attenuated Total Reflection Fourier Transform infrared (ATR-FTIR) spectroscopy and {sup 1}H nuclear magnetic resonance (NMR) to confirm the substitution of targeted functional group in ι-carrageenan. The green polymer electrolyte based on ι-carrageenan and carboxymethyl ι-carrageenan was prepared by solution-casting technique. The films were characterized by electrochemical impedance spectroscopy to determine the ionic conductivity. The ionic conductivity ι-carrageenan film were higher than carboxymethyl ι-carrageenan which 4.87 ×10{sup −6} S cm{sup −1} and 2.19 ×10{sup −8} S cm{sup −1}, respectively.

  15. Differential geometry-based solvation and electrolyte transport models for biomolecular modeling: a review

    OpenAIRE

    Wei, Guo Wei; Baker, Nathan A.

    2014-01-01

    This chapter reviews the differential geometry-based solvation and electrolyte transport for biomolecular solvation that have been developed over the past decade. A key component of these methods is the differential geometry of surfaces theory, as applied to the solvent-solute boundary. In these approaches, the solvent-solute boundary is determined by a variational principle that determines the major physical observables of interest, for example, biomolecular surface area, enclosed volume, el...

  16. Nano integrated lithium polymer electrolytes based on anodic aluminum oxide (AAO) templates

    Science.gov (United States)

    Bokalawela, Roshan S. P.

    :1) electrolyte are aligned along the pore axis and that the structure is ordered in the nano pores. This was based on our observations that the intensity of the PEO crystalline peaks at 19.2° (120) and 23.0° [(hk2) and (hk4)] when the incident x-ray beam was parallel to the pore axes was reduced, but intensity of recovered when the pores were tilted by 10° with respect to the incident x-ray beam. Exploring the infra-redred and Raman vibrational spectra of nano-confined pure PEO and PEO:LiTf(10:1) structures with the bulk films, we found that the IR absorbance bands and the Raman intensities showed a high dichroism to the normal and parallel electric fields of the IR radiation. The parallel band intensity decreased while the normal band intensity increased, consistent with an alignment of the polymer chains along the pore direction. To perform this research, on our millimeter-sized, hygroscopic samples, substantial changes in the implementation of the characterization techniques such as: AC-impedance spectroscopy, FTIR, Raman-scattering, WAXS, and SEM were required. These changes included: new sample holders to prevent water uptake; a new method to align samples to ensure consistent and reproducible measurements with the new holder designs; and the development and implementation of an entirely new system for measuring the conductivity versus temperature of our template samples in a glovebox. The Appendices at the end of this thesis include details of the developed procedures and apparatus, as well as additional experimental results not shown in the thesis.

  17. Electrolytic membrane formation of fluoroalkyl polymer using a UV-radiation-based grafting technique and sulfonation

    Energy Technology Data Exchange (ETDEWEB)

    Shironita, Sayoko; Mizoguchi, Satoko; Umeda, Minoru, E-mail: mumeda@vos.nagaokaut.ac.jp [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka 940-2188, Niigata (Japan)

    2011-03-15

    A sulfonated fluoroalkyl graft polymer (FGP) membrane was prepared as a polymer electrolyte. First, the FGP membrane was grafted with styrene under UV irradiation. The grafted FGP was then sulfonated to functionalize it for proton conductivity. The grafting degree of the membrane increased with increasing grafting time during UV irradiation. The proton conductivity of the membrane increased with increasing grafting degree. The swelling ratio was independent of the grafting time, however, the water uptake increased with increasing grafting degree. Based on these results, it was found that the UV-initiated styrene grafting occurred along the membrane thickness direction. Moreover, the membrane was embedded within the glass fibers of the composite. This composite electrolytic membrane had 1.15 times the proton conductivity of a Nafion 117 membrane.

  18. Ionic transport in P(VdF–HFP)–PEO based novel microporous polymer electrolytes

    Indian Academy of Sciences (India)

    M Deka; A Kumar

    2009-12-01

    A novel microporous polymer electrolyte (MPE) comprising blends of poly(vinylidene fluoride-cohexafluoropropylene) [P(VdF–HFP)] and polyethylene oxide (PEO) was prepared by phase inversion technique. It was observed that addition of PEO improved the pore configuration, such as pore size, pore connectivity and porosity of P(VdF–HFP) based membranes. The room temperature ionic conductivity was significantly enhanced. The highest porosity of about 65% and ionic conductivity of about 7 × 10-4 S cm-1 was obtained when the weight ratio of PEO was 40%. The liquid electrolyte uptake was found to increase with increase in porosity and pore size. However, at higher weight ratio of PEO (> 40%) porosity, pore size and ionic conductivity was decreased. This descending trend with further increase of PEO weight ratio was attributed to conglomeration effect of PEO at the pores.

  19. Proton conducting sodium alginate electrolyte laterally coupled low-voltage oxide-based transistors

    Science.gov (United States)

    Liu, Yang Hui; Qiang Zhu, Li; Shi, Yi; Wan, Qing

    2014-03-01

    Solution-processed sodium alginate electrolyte film shows a high proton conductivity of ˜5.5 × 10-3 S/cm and a high lateral electric-double-layer (EDL) capacitance of ˜2.0 μF/cm2 at room temperature with a relative humidity of 57%. Low-voltage in-plane-gate indium-zinc-oxide-based EDL transistors laterally gated by sodium alginate electrolytes are fabricated on glass substrates. The field-effect mobility, current ON/OFF ratio, and subthreshold swing of such EDL transistors are estimated to be 4.2 cm2 V-1 s-1, 2.8 × 106, and 130 mV/decade, respectively. At last, a low-voltage driven resistor-load inverter is also demonstrated. Such in-plane-gate EDL transistors have potential applications in portable electronics and low-cost biosensors.

  20. Composite polymer electrolyte based on PEO/Pvdf-HFP with MWCNT for lithium battery applications

    Science.gov (United States)

    Pradeepa, P.; Edwinraj, S.; Sowmya, G.; Kalaiselvimary, J.; Selvakumar, K.; Prabhu, M. Ramesh

    2016-05-01

    In the present study PEO and PVdF-HFP blend based composite polymer electrolytes (CPEs) has been prepared by using Multi Walled Carbon Nanotube (MWCNT), in order to examine the filler addition effect on the electrochemical properties. The complexed nanocomposite polymer electrolytes were obtained in the form of dimensionally stable and free standing films by using solution casting technique. The electrochemical properties of CPEs were measured by the AC impedance method. From the ionic conductivity results, the CPE containing MWCNT 2wt% showed the highest ionic conductivity with an excellent thermal stability at room temperature. The dielectric loss curve s for the sample 6.25wt% PEO: 18.75 wt% PVdF-HFP: 2wt% MWCNT reveal the low frequency β relaxation peak pronounced at high temperature, and it may caused by side group dipoles.

  1. Lithium salts based on a series of new anilinyl-perfluorosulfonamide salts and their polymer electrolytes

    Science.gov (United States)

    Thiam, A.; Iojoiu, C.; Leprêtre, J.-C.; Sanchez, J.-Y.

    2017-10-01

    Polymer electrolytes based on a series of new lithium anilinyl-perfluorosulfonamide exhibit conductivities close to LiTFSI ones and higher cationic transference numbers. Taking advantage of an extended delocalization on the negative charge, the anodic stability of the salts was found to range between 4.2 and 4.9 V vs Li/Li+, according to the electron-withdrawing group EWG located in para/ortho position. The simplicity of the synthesis process of the new salts, with lower fluorine content than LiPF6 and LiTFSI, paves the way for a further semi-pilot scale-up. Moreover, Linear Free Energy Relationships, LFER, were established for the first time, for both ionic conductivity and anodic stability. These LFER demonstrate unambiguously and quantitatively the conductivity dependence on anion basicity. Polymer electrolytes were soundly investigated through a variety of physicochemical and electrochemical characterizations.

  2. Fuel-Cell Electrolytes Based on Organosilica Hybrid Proton Conductors

    Science.gov (United States)

    Narayan, Sri R.; Yen, Shiao-Pin S.

    2008-01-01

    A new membrane composite material that combines an organosilica proton conductor with perfluorinated Nafion material to achieve good proton conductivity and high-temperature performance for membranes used for fuel cells in stationary, transportation, and portable applications has been developed. To achieve high proton conductivities of the order of 10(exp -1)S/cm over a wide range of temperatures, a composite membrane based on a new class of mesoporous, proton-conducting, hydrogen-bonded organosilica, used with Nafion, will allow for water retention and high proton conductivity over a wider range of temperatures than currently offered by Nafion alone. At the time of this reporting, this innovation is at the concept level. Some of the materials and processes investigated have shown good proton conductivity, but membranes have not yet been prepared and demonstrated.

  3. Ionic Liquid-Based Non-Aqueous Electrolytes for Nickel/Metal Hydride Batteries

    Directory of Open Access Journals (Sweden)

    Tiejun Meng

    2017-02-01

    Full Text Available The voltage of an alkaline electrolyte-based battery is often limited by the narrow electrochemical stability window of water (1.23 V. As an alternative to water, ionic liquid (IL-based electrolyte has been shown to exhibit excellent proton conducting properties and a wide electrochemical stability window, and can be used in proton conducting batteries. In this study, we used IL/acid mixtures to replace the 30 wt % KOH aqueous electrolyte in nickel/metal hydride (Ni/MH batteries, and verified the proton conducting character of these mixtures through electrochemical charge/discharge experiments. Dilution of ILs with acetic acid was found to effectively increase proton conductivity. By using 2 M acetic acid in 1-ethyl-3-methylimidazolium acetate, stable charge/discharge characteristics were obtained, including low charge/discharge overpotentials, a discharge voltage plateau at ~1.2 V, a specific capacity of 161.9 mAh·g−1, and a stable cycling performance for an AB5 metal hydride anode with a (Ni,Co,Zn(OH2 cathode.

  4. Redox Species-Based Electrolytes for Advanced Rechargeable Lithium Ion Batteries

    KAUST Repository

    Ming, Jun

    2016-08-15

    Seeking high-capacity cathodes has become an intensive effort in lithium ion battery research; however, the low energy density still remains a major issue for sustainable handheld devices and vehicles. Herein, we present a new strategy of integrating a redox species-based electrolyte in batteries to boost their performance. Taking the olivine LiFePO4-based battery as an example, the incorporation of redox species (i.e., polysulfide of Li2S8) in the electrolyte results in much lower polarization and superior stability, where the dissociated Li+/Sx2– can significantly speed up the lithium diffusion. More importantly, the presence of the S82–/S2– redox reaction further contributes extra capacity, making a completely new LiFePO4/Li2Sx hybrid battery with a high energy density of 1124 Wh kgcathode–1 and a capacity of 442 mAh gcathode–1. The marriage of appropriate redox species in an electrolyte for a rechargeable battery is an efficient and scalable approach for obtaining higher energy density storage devices.

  5. Silica-scavenging effects in ceria-based solid electrolytes

    Directory of Open Access Journals (Sweden)

    Ivanova, D.

    2008-08-01

    Full Text Available Composite materials based on gadolinium doped ceria (CGO with additions of silica, with both silica and lanthanum oxide, and with lanthanum silicate, were prepared by the conventional ceramic route, to assess the silica scavenging role of lanthanum oxide additions. Structural, microstructural and electrical characterization of these samples confirmed the formation of one apatite type lanthanum silicate-based phase from reaction of silica with lanthanum oxide. The formation of this phase occurred in parallel with a significant enhancement of the grain boundary conductivity of these composite materials. Further interaction between constituents, involving diffusion of La to CGO, and Ce and Gd to the apatite phase, had no significant consequences on the electrical performance of these materials. Overall, lanthanum oxide was shown to remove the siliceous phases from the grain boundaries of CGO.

    Se prepararon materiales compuestos basados en óxido de cerio dopado con gadolinio (TGO con adicciones de sílice, con sílice y óxido de lantano y silicato del lantano, mediante procesamiento cerámico convencional con objeto de confirmar el papel secuestrante de sílice de las adicciones. La caracterización estructural, microestructural y eléctrica de las muestras confirmó la formación de una fase tipo apatito basada en silicato de lantano a partir de la reacción de la sílice con el óxido de lantano. La formación de esta fase ocurre en paralelo con un incremento significativo de la conductividad a través del borde de grano de estos materiales. La interacción entre los constituyentes, incluyendo la difusión del La al CGO, y el Ce y el Gd a la fase apatito, no tiene consecuencias significativas sobre el comportamiento eléctrico de estos materiales. Resumiendo, el óxido de lantano es capaz de eliminar las fases silicias del borde de grano del CGO.

  6. Preparation and Characterization of a Hybrid Solid Polymer Electrolyte Consisting of Poly(Ethyleneoxide) and Poly(Acrylonitrile) for Polymer-Battery Application

    OpenAIRE

    Nookala, Munichandraiah; Scanlon, Lawrence G; Marsh, Richard A

    1997-01-01

    For application in an ambient temperature solid state lithium battery a highly dimensionally-stable polymer electrolyte based on polyethyleneoxide (PEO) suffers from low ionic conductivity, whereas a highly conducting gel electrolyte based on polyacrylonitrile (PAN) suffers from low dimensional stability. In order to overcome these problems, a hybrid solid polymer electrolyte (HSPE) was prepared using PEO, PAN, propylene carbonate (PC), ethylene carbonate (EC) and lithium perchlorate. The HSP...

  7. Ionic Liquid-Based Polymer Electrolytes via Surfactant-Assisted Polymerization at the Plasma-Liquid Interface.

    Science.gov (United States)

    Tran, Quoc Chinh; Bui, Van-Tien; Dao, Van-Duong; Lee, Joong-Kee; Choi, Ho-Suk

    2016-06-29

    We first report an innovative method, which we refer to as interfacial liquid plasma polymerization, to chemically cross-link ionic liquids (ILs). By this method, a series of all-solid state, free-standing polymer electrolytes is successfully fabricated where ILs are used as building blocks and ethylene oxide-based surfactants are employed as an assisted-cross-linking agent. The thickness of the films is controlled by the plasma exposure time or the ratio of surfactant to ILs. The chemical structure and properties of the polymer electrolyte are characterized by scanning electron microscopy (SEM), Fourier transformation infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) spectroscopy, X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), and electrochemical impedance spectroscopy (EIS). Importantly, the underlying polymerization mechanism of the cross-linked IL-based polymer electrolyte is studied to show that fluoroborate or halide anions of ILs together with the aid of a small amount of surfactants having ethylene oxide groups are necessary to form cross-linked network structures of the polymer electrolyte. The ionic conductivity of the obtained polymer electrolyte is 2.28 × 10(-3) S·cm(-1), which is a relatively high value for solid polymer electrolytes synthesized at room temperature. This study can serve as a cornerstone for developing all-solid state polymer electrolytes with promising properties for next-generation electrochemical devices.

  8. Capillary gel electrophoresis of oligonucleotides: prediction of migration times using base-specific migration coefficients

    NARCIS (Netherlands)

    Cordier, Y.; Roch, O.; Cordier, P.; Bischoff, Rainer

    1994-01-01

    Chemically synthesized oligodeoxyribonucleotides were subjected to capillary gel electrophoresis on three different polyacrylamide-based matrices. Analysis of about 1000 samples over a 1-year period showed that the gel matrix evolved with time resulting in shifting migration times, making it

  9. NMR spectroscopy study of agar-based polymers electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Mattos, R.I.; Tambelli, C.E. [Universidade de Sao Paulo (USP), Pirassununga, SP (Brazil). Fac. de Zootecnia e Engenharia de Alimentos; Raphael, E. [Universidade Federal de Sao Joao del-Rey (UFSJ), MG (Brazil). Dept. de Ciencias Naturais; Silva, I.D.A.; Magon, C.J.; Donoso, J.P. [Universidade de Sao Paulo (IFSC/USP), Sao Carlos, SP (Brazil). Inst. de Fisica

    2012-07-01

    Full text: This communication presents the results of preparation and characterization of transparent films obtained from agar and acetic acid. The films were characterized by electrochemical impedance spectroscopy (EIS) and nuclear magnetic resonance (NMR). The film formed by agar (Sigma Aldrich) was dispersed in water and kept under stirring and heating at 100 deg C. Next, glycerol, formaldehyde and different quantities of acetic acid (25 and 50 wt%) were added to this solution. The obtained solution was placed on a glass plate and left to dry for 48 hours in oven at 50 deg C to obtain the films, which were kept under vacuum before characterization. The ionic conductivity of the films display an Arrhenius behavior with activation energy E{sub a} = 78 (25 wt% of acetic acid) and E{sub a} = 87 kJ/mol (50 wt% of acetic acid). The conductivity values were 3:0 X 10{sup -6} and 1:2 X 10{sup -4} S/cm at room temperature and 4:4 X 10{sup -4} and 1:5 X 10{sup -3}S/cm at 70 deg C, for the 25 and 50 wt% of acetic acid respectively. To investigate the mechanism of protonic conduction in the polymer proton conductor proton NMR measurements were performed in the temperature range 200-370 K. The {sup 1}H-NMR results exhibit the qualitative feature associated with the proton mobility, namely the presence of well defined {sup 1}H spin-lattice relaxation maxima at 300 K. Activation energy of the order of 40 kJ/mol was obtained from the {sup 1}H-NMR line narrowing data. The ionic conductivity of the film combined with their transparency, flexibility, homogeneity and good adhesion to the glasses or metals indicate that agar-based SPEs are promising materials for used on optoelectronic applications. (author)

  10. Chemical Sensors Based on Molecularly Imprinted Sol-Gel Materials

    Directory of Open Access Journals (Sweden)

    Franz L. Dickert

    2010-03-01

    Full Text Available The sol-gel technique is earning the worldwide attention of researchers in the field of material science, due to its versatility in synthesizing inorganic ceramic materials at mild conditions. High purity, homogeneity, controlled porosity, stable temperature and nanoscale structuring are the most remarkable features offered by this method for generating highly sensitive and selective matrices to incorporate analyte molecules. The crafting of sol-gel sensors through molecular imprinting has put great influence on the development of innovative chemical sensors, which can be seen from the growing number of publications in this field. The review provides a brief overview of sol-gel sensor applications, and discusses the contribution of molecular imprinting in exploring the new world of sensors.

  11. A versatile polyacrylamide gel electrophoresis based sulfotransferase assay

    Directory of Open Access Journals (Sweden)

    Prather Brittany

    2010-02-01

    Full Text Available Abstract Background Sulfotransferases are a large group of enzymes that regulate the biological activity or availability of a wide spectrum of substrates through sulfation with the sulfur donor 3'-phosphoadenosine-5'-phosphosulfate (PAPS. These enzymes are known to be difficult to assay. A convenient assay is needed in order to better understand these enzymes. Results A universal sulfotransferase assay method based on sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE is described. This assay has been successfully applied to substrates as small as α-naphthol and as big as proteoglycans. As examples, we present the assays for recombinant human CHST4, TPST1, CHST3 and HS6ST1. In order to assess whether a small molecule can be applicable to this type of assay, a method to estimate the relative mobility of a molecule to PAPS is also presented. The estimated relative mobilities of various sulfated small molecules generated by SULT1A1, SULT1E1, SULT2A1 and CHST4 are in the range of ± 0.2 of the actual relative mobilities. Conclusion The versatility of the current method comes from the ability that SDS-PAGE can separate proteins and small molecules according to different parameters. While mobilities of proteins during SDS-PAGE are inversely related to their sizes, mobilities of small molecules are positively related to their charge/mass ratios. The predicted relative mobility of a product to PAPS is a good indicator of whether a sulfotransferase can be assayed with SDS-PAGE. Because phosphorylation is most similar to sulfation in chemistry, the method is likely to be applicable to kinases as well.

  12. Advances in the electrodeposition of aluminum from ionic liquid based electrolytes

    Science.gov (United States)

    Leadbetter, Kirt C.

    Aluminum plating is of considerable technical and economic interest because it provides an eco-friendly substitute for cadmium coatings used on many military systems. However, cadmium has been determined to be a significant environmental safety and occupational health (ESOH) hazard because of its toxicity and carcinogenic nature. Furthermore, the cost of treating and disposing of generated wastes, which often contain cyanide, is costly and is becoming prohibitive in the face of increasingly stringent regulatory standards. The non-toxic alternative aluminum is equivalent or superior in performance to cadmium. In addition, it could serve to provide an alternative to hexavalent chromium coatings used on military systems for similar reasons to that of cadmium. Aluminum is a beneficial alternative in that it demonstrates self-healing corrosion resistance in the form of a tightly-bound, impervious oxide layer. A successfully plated layer would be serviceable over a wider temperature range, 925 °F for aluminum compared to 450 oF for cadmium. In addition, an aluminum layer can be anodized to make it non-conducting and colorable. In consideration of the plating process, aluminum cannot be deposited from aqueous solutions because of its reduction potential. Therefore, nonaqueous electrolytes are required for deposition. Currently, aluminum can be electrodeposited in nonaqueous processes that use hazardous chemicals such as toluene and pyrophoric aluminum alkyls. Electrodeposition from ionic liquids provides the potential for a safer method that could be easily scaled up for industrial application. The plating process could be performed at a lower temperature and higher current density than other commercially available aluminum electrodeposition processes; thus a reduced process cost could be possible. The current ionic liquid based electrolytes are more expensive; however production on a larger scale and a long electrolyte lifetime are associated with a reduction in price

  13. Electrical transport study of potato starch-based electrolyte system-II

    Energy Technology Data Exchange (ETDEWEB)

    Tiwari, Tuhina; Kumar, Manindra [Department of Physics (Mahila Mahavidyalay), Banaras Hindu University, Varanasi (India); Srivastava, Neelam, E-mail: neelamsrivastava_bhu@yahoo.co.in [Department of Physics (Mahila Mahavidyalay), Banaras Hindu University, Varanasi (India); Srivastava, P.C. [Department of Physics, Banaras Hindu University, Varanasi (India)

    2014-03-15

    Highlights: • Cheap and bio-degradable polymer electrolyte. • High conductivity ∼ 9.59 × 10{sup −3} Scm{sup −1}. • Detailed ion dynamics stud. -- Abstract: Glutaraldehyde (GA) crosslinked potato starch, after mixing with sodium iodide (NaI), resulted in electrolyte film having conductivity (σ) ∼ 10{sup −3} S/cm and ionic transference number (t{sub ion}) ≥ 0.99. Out of two preparation mediums, namely methanol and acetone, methanol based electrolyte system seems to be better. Super-linear power law (SLPL) phenomenon is observed in MHz frequency range and both lattice site potential and coulomb cage potential due to neighboring mobile charge carriers seems to be responsible for existence of SLPL, and variation of power law exponent ‘n’ with salt concentration. These ion dynamics results are supported by dielectric data also. Estimated number of charge carriers ‘N’ and mobility ‘μ’ are discussed with reference to different variants (medium of preparation, plasticizer, and salt content). Material's conductivity strongly depends on humidity.

  14. PREPARATION AND ELECTROCHEMICAL CHARACTERISTICS OF POLYMER ELECTROLYTE MEMBRANES BASED ON SAN/PVDF-HFP BLENDS

    Institute of Scientific and Technical Information of China (English)

    Ding-guo Tang; Lu Qi; Yun-xiang Ci

    2006-01-01

    A copolymer of poly(acrylonitrile-co-styrene) (SAN) was synthesized via an emulsion polymerization method.Novel polymer electrolyte membranes cast from the blends of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), SAN and fumed silica (SiO2) are microporous and can be used in polymer lithium-ion batteries. The membrane shows excellent characteristics such as high ionic conductivity and good mechanical strength when the mass ratio between SAN and PVDF-HFP and SiO2 is 3.5/31.5/5. The ionic conductivity of the membrane soaked in a liquid electrolyte of 1 mol/L LiPF6/EC/DMC/DEC is 4.9 × 10-3 Scm-1 at 25℃. The membrane is electrochemical stable up to 5.5 V versus Li+/Li in the liquid electrolyte. The influences of SiO2 content on the porosity and mechanical strength of the membranes were studied.Polymer lithium-ion batteries based on the membranes were assembled and their performances were also studied.

  15. Synthesis and characterization of an electrolyte system based on a biodegradable polymer

    Directory of Open Access Journals (Sweden)

    K. Sownthari

    2013-06-01

    Full Text Available A polymer electrolyte system has been developed using a biodegradable polymer namely poly-ε-caprolactone (PCL in combination with zinc triflate [Zn(CF3SO32] in different weight percentages and characterized during this investigation. Free-standing thin films of varying compositions were prepared by solution casting technique. The successful doping of the polymer has been confirmed by means of Fourier transform infrared spectroscopy (FTIR by analyzing the carbonyl (C=O stretching region of the polymer. The maximum ionic conductivity obtained at room temperature (25°C was found to be 8.8x10–6 S/cm in the case of PCL complexed with 25 wt% Zn(CF3SO32 which is five orders of magnitude higher than that of the pure polymer host material. The increase in amorphous phase with an increase in salt concentration of the prepared polymer electrolyte has also been confirmed from the concordant results obtained from X-ray diffraction (XRD, differential scanning calorimetry (DSC and scanning electron microscopic (SEM analyses. Furthermore, the electrochemical stability window of the prepared polymer electrolyte was found to be 3.7 V. An electrochemical cell has been fabricated based on Zn/MnO2 electrode couple as an application area and its discharge characteristics were evaluated.

  16. Surface Properties of PAN-based Carbon Fibers Modified by Electrochemical Oxidization in Organic Electrolyte Systems

    Directory of Open Access Journals (Sweden)

    WU Bo

    2016-09-01

    Full Text Available PAN-based carbon fibers were modified by electrochemical oxidization using fatty alcohol polyoxyethylene ether phosphate (O3P, triethanolamine (TEOA and fatty alcohol polyoxyethylene ether ammonium phosphate (O3PNH4 as organic electrolyte respectively. Titration analysis, single fiber fracture strength measurement and field emission scanning electron microscopy (FE-SEM were used to evaluate the content of acidic functional group on the surface, mechanical properties and surface morphology of carbon fiber. The optimum process of electrochemical treatment obtained is at 50℃ for 2min and O3PNH4 (5%, mass fraction as the electrolyte with current density of 2A/g. In addition, the surface properties of modified carbon fibers were characterized by X-ray photoelectron spectroscopy (XPS and single fiber contact angle test. The results show that the hydrophilic acidic functional groups on the surface of carbon fiber which can enhance the surface energy are increased by the electrochemical oxidation using O3PNH4 as electrolyte, almost without any weakening to the mechanical properties of carbon fiber.

  17. A new nanocomposite polymer electrolyte based on poly(vinyl alcohol) incorporating hypergrafted nano-silica

    KAUST Repository

    Hu, Xian-Lei

    2012-01-01

    Solid-state nanocomposite polymer electrolytes based on poly(vinyl alcohol)(PVA) incorporating hyperbranched poly(amine-ester) (HBPAE) grafted nano-silica (denoted as SiO2-g-HBPAE) have been prepared and investigated. Through surface pretreatment of nanoparticles, followed by Michael-addition and a self-condensation process, hyperbranched poly(amine-ester) was directly polymerized from the surface of nano-silica. Then the hypergrafted nanoparticles were added to PVA matrix, and blended with lithium perchlorate via mold casting method to fabricate nanocomposite polymer electrolytes. By introducing hypergrafted nanoparticles, ionic conductivity of solid composite is improved significantly at the testing temperature. Hypergrafted nano-silica may act as solid plasticizer, promoting lithium salt dissociation in the matrix as well as improving segmental motion of matrix. In addition, tensile testing shows that such materials are soft and tough even at room temperature. From the dielectric spectra of nanocomposite polymer electrolyte as the function of temperature, it can be deduced that Arrhenius behavior appears depending on the content of hypergrafted nano-silica and concentration of lithium perchlorate. At a loading of 15 wt% hypergrafted nano-silica and 54 wt% lithium perchlorate, promising ionic conductivities of PVA nanocomposite polymer electrolyte are achieved, about 1.51 × 10 -4 S cm-1 at 25 °C and 1.36 × 10-3 S cm-1 at 100 °C. © The Royal Society of Chemistry.

  18. Sol-gel based alumina powders with catalytic applications

    Science.gov (United States)

    Crişan, Maria; Zaharescu, Maria; Kumari, Valluri Durga; Subrahmanyam, Machiraju; Crişan, Dorel; Drăgan, Nicolae; Răileanu, Mălina; Jitianu, Mihaela; Rusu, Adriana; Sadanandam, Gullapelli; Krishna Reddy, Jakkidi

    2011-10-01

    The sol-gel process provides a new approach to the preparation of oxide materials and offers many advantages for making catalysts. Since homogeneous mixing can be achieved at the molecular scale, the chemical reactivity of the oxide surface can be greatly enhanced; thus powders with high surface area and optimized pore size distribution can be obtained at low temperatures. In the present work NiO/Al 2O 3 sol-gel catalysts were obtained by simultaneous gelation of aluminium isopropoxide and nickel nitrate. A comparative study with pure sol-gel alumina was also realized. By physical-structural studies the changes induced by the introduction of the Ni precursor, before and after aluminium alkoxide hydrolysis were highlighted. The introduction of Ni at the beginning of the reaction favors γ-Al 2O 3 crystallization. When Ni is added at the end of reaction, it delays the alumina crystallization and induces the disorder of the lattice. The obtained Ni doped sol-gel derived alumina has been used as catalyst in the finished form for glycerol reforming to generate H 2 for fuel cell applications. Some evaluation results of Ni-doped alumina combined with TiO 2 in photocatalytic glycerol reforming reaction have been included.

  19. Chemical and thermomechanical compatibility between neodymium manganites and electrolytes based on ceria

    Directory of Open Access Journals (Sweden)

    Gil, V.

    2008-06-01

    Full Text Available The goal of this work was to study the thermal expansion behaviour and to establish the phase relations between NdMe0.5Mn0.5O3 (Me=Ni, Co solid solutions as cathodes and two electrolytes based on Ce0.9Gd0.1O1.95. Doping of electrolyte with 1.0 wt% Bi2O3 was employed in order to improve the densification process. The cathode-electrolyte pairs were obtained by isostatic pressing of constituent powders and posterior sintering using the temperature ranges between 1350–1400 ºC for 2 h. The sintering conditions were optimized to obtain highly densificated electrolytes and well-developed cathode-electrolyte interfaces. Scanning electron microscopy observation with EDAX analysis was performed in cathode-electrolyte interfacial regions in order to characterize the obtained microstructures and to determine possible cation diffusions from the cathode into the electrolyte. It is found that the nickel doped manganite, NdNi0.5Mn0.5O3, is chemically and thermo-mechanically compatible with both electrolytes without formation of new phases up to 1400ºC even during long time of treatments.

    El propósito del presente trabajo es establecer las relaciones de fase entre soluciones sólidas NdMe0.5Mn0.5O3 (Me=Ni, Co y electrolitos Ce0.9Gd0.1O1.95 para su uso como cátodos y electrolitos SOFC, respectivamente. El electrolito fue en ocasiones dopado con 1.0 wt% Bi2O3 con el objeto de mejorar su densificación. Así mismo se estudia el comportamiento termomecánico de dichos materiales. Los pares cátodo-electrolito fueron obtenidos a partir de polvos prensados isostáticamente y posteriormente sinterizados utilizando unos rangos de temperatura entre 1350 y 1400ºC durante 2h. Las condiciones de sinterización fueron optimizadas para obtener unos electrolitos altamente densificados y unas interfaces cátodo-electrolito bien definidas. La caracterización microestructural de las regiones interfaciales fue llevada a cabo mediante microscopía electrónica de

  20. Neurologic presentations of acid-base imbalance, electrolyte abnormalities, and endocrine emergencies.

    Science.gov (United States)

    Yee, Alan H; Rabinstein, Alejandro A

    2010-02-01

    Accurate identification of nervous system dysfunction is vital in the assessment of any multisystem disorder. The neurologic manifestations of acid-base disturbances, abnormal electrolyte concentrations, and acute endocrinopathies are protean and typically determined by the acuity of the underlying derangement. Detailed history and physical examination may guide appropriate laboratory testing and lead to prompt and accurate diagnosis. Neurologic manifestations of primary and secondary systemic disorders are frequently encountered in all subspecialties of medicine. This article focuses on key neurologic presentations of respiratory and metabolic acid-base derangements and potentially life-threatening endocrinopathies.

  1. Bacterial reduction of alcohol-based liquid and gel products on hands soiled with blood.

    Science.gov (United States)

    Kawagoe, Julia Y; Graziano, Kazuko Uchikawa; Martino, Marines Dalla Valle; Siqueira, Itacy; Correa, Luci

    2011-11-01

    The antibacterial efficacy of three alcohol-based products (liquid and gel) were tested on the hands with blood and contaminated with Serratia marcescens (ATCC 14756), using EN 1500 procedures in 14 healthy volunteers. The alcohol-based products tested, either gel or liquid-based, reached bacterial reduction levels higher than 99.9% in the presence of blood and did not differ significantly (ANOVA test; P = 0.614).

  2. Combining high-throughput MALDI-TOF mass spectrometry and isoelectric focusing gel electrophoresis for virtual 2D gel-based proteomics.

    Science.gov (United States)

    Lohnes, Karen; Quebbemann, Neil R; Liu, Kate; Kobzeff, Fred; Loo, Joseph A; Ogorzalek Loo, Rachel R

    2016-07-15

    The virtual two-dimensional gel electrophoresis/mass spectrometry (virtual 2D gel/MS) technology combines the premier, high-resolution capabilities of 2D gel electrophoresis with the sensitivity and high mass accuracy of mass spectrometry (MS). Intact proteins separated by isoelectric focusing (IEF) gel electrophoresis are imaged from immobilized pH gradient (IPG) polyacrylamide gels (the first dimension of classic 2D-PAGE) by matrix-assisted laser desorption/ionization (MALDI) MS. Obtaining accurate intact masses from sub-picomole-level proteins embedded in 2D-PAGE gels or in IPG strips is desirable to elucidate how the protein of one spot identified as protein 'A' on a 2D gel differs from the protein of another spot identified as the same protein, whenever tryptic peptide maps fail to resolve the issue. This task, however, has been extremely challenging. Virtual 2D gel/MS provides access to these intact masses. Modifications to our matrix deposition procedure improve the reliability with which IPG gels can be prepared; the new procedure is described. Development of this MALDI MS imaging (MSI) method for high-throughput MS with integrated 'top-down' MS to elucidate protein isoforms from complex biological samples is described and it is demonstrated that a 4-cm IPG gel segment can now be imaged in approximately 5min. Gel-wide chemical and enzymatic methods with further interrogation by MALDI MS/MS provide identifications, sequence-related information, and post-translational/transcriptional modification information. The MSI-based virtual 2D gel/MS platform may potentially link the benefits of 'top-down' and 'bottom-up' proteomics.

  3. Study of ion diffusional motion in ionic liquid-based polymer electrolytes by simultaneous solid state NMR and DTA.

    Science.gov (United States)

    Rajput, Dushyant Singh; Yamada, Koji; Sekhon, S S

    2013-02-28

    Polymer electrolytes containing ionic liquid (IL), 2-methyl-1,3-dipropylimidazolium dihydrogenphosphate (MDPImH2PO4) have been studied by (1)H solid state NMR and differential thermal analysis (DTA) simultaneously by using a specially designed probe. To the best of our knowledge, this is the first report of its kind for IL based polymer electrolytes. The variation of NMR line width with temperature for the IL and polymer electrolytes shows line narrowing at the glass transition and melting temperature. The onset of long-range ion diffusional motion also takes place at these temperatures and is accompanied by a sudden increase in ionic conductivity value by 2-3 orders of magnitude. The presence of amorphous and crystalline phases in IL-based polymer electrolytes has been observed from X-ray diffraction (XRD) studies, and the amorphous phase is the high conducting phase in these polymer electrolytes. The IL-based polymer electrolytes have been observed to be thermally stable up to 200 °C. The results obtained from ion transport studies have also been supported by Fourier transform infrared (FTIR), XRD, and cyclic voltammetry (CV) studies.

  4. Lithium battery with solid polymer electrolyte based on comb-like copolymers

    Science.gov (United States)

    Daigle, Jean-Christophe; Vijh, Ashok; Hovington, Pierre; Gagnon, Catherine; Hamel-Pâquet, Julie; Verreault, Serge; Turcotte, Nancy; Clément, Daniel; Guerfi, Abdelbast; Zaghib, Karim

    2015-04-01

    In this paper we report on the synthesis of comb-like copolymers as solid polymer electrolytes (SPE). The synthesis involved anionic polymerization of styrene (St) and 4-vinylanisole (VA) as the followed by grafting of poly(ethylene glycol) monomethyl ether methacrylate (PEGMA) by Atom Transfer Radical Polymerization (ATRP). The comb-like copolymer's structure was analyzed by Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) and gel permeation chromatography (GPC). The membranes were made by solvent casting and the morphologies were analyzed by atomic forces microscopy (AFM) and scanning electron microscopy (SEM). We observed that a nano and micro phase separation occurs which improves ionic conductivity. The ionic conductivities were determined by AC Impedance, which showed that the SPEs have good conductivities (10-5 Scm-1) at room temperature owing to the negligible values (<10 kJ mol-1) of the activation energies for conductivity. The batteries with these polymers exhibit a capacity of 146 mAh g-1 at C/24, and no evidence of degradation after intense cycling was observed. However, poor cycle life was observed at C/6 and C/3, which is a consequence of several factors. We partially explain that behavior by arguing that whereas PEO lightly "solvates" Li+ thus slowing Li-ion mobility, and PEGMA chains "solvate" Li ions too strongly, trapping and inhibiting their mobility.

  5. Blood grouping based on PCR methods and agarose gel electrophoresis.

    Science.gov (United States)

    Sell, Ana Maria; Visentainer, Jeane Eliete Laguila

    2015-01-01

    The study of erythrocyte antigens continues to be an intense field of research, particularly after the development of molecular testing methods. More than 300 specificities have been described by the International Society for Blood Transfusion as belonging to 33 blood group systems. The polymerase chain reaction (PCR) is a central tool for red blood cells (RBC) genotyping. PCR and agarose gel electrophoresis are low cost, easy, and versatile in vitro methods for amplifying defined target DNA (RBC polymorphic region). Multiplex-PCR, AS-PCR (Specific Allele Polymerase Chain Reaction), and RFLP-PCR (Restriction Fragment Length Polymorphism-Polymerase Chain Reaction) techniques are usually to identify RBC polymorphisms. Furthermore, it is an easy methodology to implement. This chapter describes the PCR methodology and agarose gel electrophoresis to identify the polymorphisms of the Kell, Duffy, Kidd, and MNS blood group systems.

  6. Data Visualization and Feature Selection Methods in Gel-based Proteomics

    DEFF Research Database (Denmark)

    Silva, Tomé Santos; Richard, Nadege; Dias, Jorge P.;

    2014-01-01

    Despite the increasing popularity of gel-free proteomic strategies, two-dimensional gel electrophoresis (2DE) is still the most widely used approach in top-down proteomic studies, for all sorts of biological models. In order to achieve meaningful biological insight using 2DE approaches, importance......-based proteomics, summarizing the current state of research within this field. Particular focus is given on discussing the usefulness of available multivariate analysis tools both for data visualization and feature selection purposes. Visual examples are given using a real gel-based proteomic dataset as basis....

  7. Structure and Properties of Polysaccharide Based BioPolymer Gels

    Science.gov (United States)

    Prud'Homme, Robert K.

    2000-03-01

    Nature uses the pyranose ring as the basic building unit for a wideclass of biopolymers. Because of their biological origin these biopolymers naturally find application as food additives, rheology modifiers. These polymers range from being rigid skeletal material, such as cellulose that resist dissolution in water, to water soluble polymers, such as guar or carrageenan. The flexibility of the basic pyranose ring structure to provide materials with such a wide range of properties comes from the specific interactions that can be engineered by nature into the structure. We will present several examples of specific interactions for these systems: hydrogen bonding, hydrophobic interactions, and specific ion interactions. The relationship between molecular interations and rheology will be emphasized. Hydrogen bonding mediated by steric interference is used to control of solubility of starch and the rheology of guar gels. A more interesting example is the hydrogen bonding induced by chemical modification in konjac glucomannan that results in a gel that melts upon cooling. Hydrogen bonding interactions in xanthan lead to gel formation at very low polymer concentrations which is a result of the fine tuning of the polymer persistence length and total contour length. Given the function of xanthan in nature its molecular architecture has been optimized. Hydrophobic interactions in methylcellulose show a reverse temperature dependence arising from solution entropy. Carrageenan gelation upon the addition of specific cations will be addressed to show the interplay of polymer secondary structure on chemical reactivity. And finally the cis-hydroxyls on galactomannans permit crosslinking by a variety of metal ions some of which lead to "living gels" and some of which lead to permanently crosslinked networks.

  8. The Doping Effect on Conductivity and Glass Transition Temperature of Solid Polymeric Electrolyte Based on Polyvinylchloride (pvc)

    Science.gov (United States)

    Abd. Rahman, Mohd. Yusri; Mat Salleh, Muhammad; Abu Talib, Ibrahim; Yahaya, Muhamad

    2002-12-01

    Solid electrolyte materials have been widely used in electrochemical devices such as batteries, solar cells and displays. This is because of its advantages over the liquidmaterial.This paper is concerned with the preparation of solid polymeric electrolyte based on polyvinylchloride (PVC) and its conductivity .The effect of percentage by weight of dopant material (LiClO4) on conductivity and glass transition temperature of the electrolyte was studied by using differential scanning calorimeter (DSC) and impedance spectroscopy technique. The electrolyte doped with 4.8%wt LiClO4 exhibits the highest conductivitiy of 7 × 10-6Scm-1 at room temperature but has the lowest glass transition temperature of 36.37°C. The other results are presented in this paper.

  9. The NASA "PERS" Program: Solid Polymer Electrolyte Development for Advanced Lithium-Based Batteries

    Science.gov (United States)

    Baldwin, Richard S.; Bennett, William R.

    2007-01-01

    In fiscal year 2000, The National Aeronautics and Space Administration (NASA) and the Air Force Research Laboratory (AFRL) established a collaborative effort to support the development of polymer-based, lithium-based cell chemistries and battery technologies to address the next generation of aerospace applications and mission needs. The ultimate objective of this development program, which was referred to as the Polymer Energy Rechargeable System (PERS), was to establish a world-class technology capability and U.S. leadership in polymer-based battery technology for aerospace applications. Programmatically, the PERS initiative exploited both interagency collaborations to address common technology and engineering issues and the active participation of academia and private industry. The initial program phases focused on R&D activities to address the critical technical issues and challenges at the cell level. Out of a total of 38 proposals received in response to a NASA Research Announcement (NRA) solicitation, 18 proposals (13 contracts and 5 grants) were selected for initial award to address these technical challenges. Brief summaries of technical approaches, results and accomplishments of the PERS Program development efforts are presented. With Agency support provided through FY 2004, the PERS Program efforts were concluded in 2005, as internal reorganizations and funding cuts resulted in shifting programmatic priorities within NASA. Technically, the PERS Program participants explored, to various degrees over the lifetime of the formal program, a variety of conceptual approaches for developing and demonstrating performance of a viable advanced solid polymer electrolyte possessing the desired attributes, as well as several participants addressing all components of an integrated cell configuration. Programmatically, the NASA PERS Program was very successful, even though the very challenging technical goals for achieving a viable solid polymer electrolyte material or

  10. Rigid-flexible coupling high ionic conductivity polymer electrolyte for an enhanced performance of LiMn2O4/graphite battery at elevated temperature.

    Science.gov (United States)

    Hu, Pu; Duan, Yulong; Hu, Deping; Qin, Bingsheng; Zhang, Jianjun; Wang, Qingfu; Liu, Zhihong; Cui, Guanglei; Chen, Liquan

    2015-03-04

    LiMn2O4-based batteries exhibit severe capacity fading during cycling or storage in LiPF6-based liquid electrolytes, especially at elevated temperatures. Herein, a novel rigid-flexible gel polymer electrolyte is introduced to enhance the cyclability of LiMn2O4/graphite battery at elevated temperature. The polymer electrolyte consists of a robust natural cellulose skeletal incorporated with soft segment poly(ethyl α-cyanoacrylate). The introduction of the cellulose effectively overcomes the drawback of poor mechanical integrity of the gel polymer electrolyte. Density functional theory (DFT) calculation demonstrates that the poly(ethyl α-cyanoacrylate) matrices effectively dissociate the lithium salt to facilitate ionic transport and thus has a higher ionic conductivity at room temperature. Ionic conductivity of the gel polymer electrolyte is 3.3 × 10(-3) S cm(-1) at room temperature. The gel polymer electrolyte remarkably improves the cycling performance of LiMn2O4-based batteries, especially at elevated temperatures. The capacity retention after the 100th cycle is 82% at 55 °C, which is much higher than that of liquid electrolyte (1 M LiPF6 in carbonate solvents). The polymer electrolyte can significantly suppress the dissolution of Mn(2+) from surface of LiMn2O4 because of strong interaction energy of Mn(2+) with PECA, which was investigated by DFT calculation.

  11. Lithium secondary batteries using an asymmetric sulfonium-based room temperature ionic liquid as a potential electrolyte

    Institute of Scientific and Technical Information of China (English)

    LUO ShiChun; ZHANG ZhengXi; YANG Li

    2008-01-01

    A new asymmetric sulfonium-based ionic liquid, 1-butyldimethylsulfonium bis(trifluoromethylsulfonyl) imide (S114TFSI), was developed as electrolyte material for lithium secondary battery. Its cathodic po-tential was a little more positive against the Li/Li+, so vinylene carbonate (VC) was added into the LiTFSI/S114TFSI ionic liquid electrolyte to ensure the formation of a solid electrolyte interface (SEI), which effectively prevented the decomposition of the electrolyte. The properties of the Li/LiMn2O4 cell containing S114TFSI-based electrolyte were studied and the cycle performances were compared to Electrochemical impedance spectroscopy (EIS) and X-ray diffraction (XRD) were conducted to analyze the mechanisms affecting the cell performances at different temperatures. The lithium secondary bat-tery system, using the above ionic liquid electrolyte material, shows good cycle performances and good safety at room temperature, and is worthwhile to further investigate so as to find out the potential application.

  12. Organosilicon-Based Electrolytes for Long-Life Lithium Primary Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Fenton, Kyle R. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Nagasubramanian, Ganesan [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Staiger, Chad L. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Pratt, III, Harry D. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Rempe, Susan B. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Leung, Kevin [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Chaudhari, Mangesh I. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Anderson, Travis Mark [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    This report describes advances in electrolytes for lithium primary battery systems. Electrolytes were synthesized that utilize organosilane materials that include anion binding agent functionality. Numerous materials were synthesized and tested in lithium carbon monofluoride battery systems for conductivity, impedance, and capacity. Resulting electrolytes were shown to be completely non-flammable and showed promise as co-solvents for electrolyte systems, due to low dielectric strength.

  13. An efficient dissipative particle dynamics-based algorithm for simulating electrolyte solutions

    CERN Document Server

    Medina, Stefan; Wang, Zhen-Gang; Schmid, Friederike

    2014-01-01

    We propose an efficient simulation algorithm based on the dissipative particle dynamics (DPD) method for studying electrohydrodynamic phenomena in electrolyte fluids. The fluid flow is mimicked with DPD particles while the evolution of the concentration of the ionic species is described using Brownian pseudo particles. The method is designed especially for systems with high salt concentrations, as explicit treatment of the salt ions becomes computationally expensive. For illustration, we apply the method to electro-osmotic flow over patterned, superhydrophobic surfaces. The results are in good agreement with recent theoretical predictions.

  14. Acid-base and electrolyte abnormalities in heart failure: pathophysiology and implications.

    Science.gov (United States)

    Urso, Caterina; Brucculeri, Salvatore; Caimi, Gregorio

    2015-07-01

    Electrolyte and acid-base abnormalities are a frequent and potentially dangerous complication in subjects with congestive heart failure. This may be due either to the pathophysiological alterations present in the heart failure state leading to neurohumoral activation (stimulation of the renin-angiotensin-aldosterone system, sympathoadrenergic stimulation), or to the adverse events of therapy with diuretics, cardiac glycosides, and ACE inhibitors. Subjects with heart failure may show hyponatremia, magnesium, and potassium deficiencies; the latter two play a pivotal role in the development of cardiac arrhythmias. The early identification of these alterations and the knowledge of the pathophysiological mechanisms are very useful for the management of these patients.

  15. Electrochemical performance of poly(vinyl alcohol)-based solid polymer electrolyte for lithium polymer batteries.

    Science.gov (United States)

    Kim, Young-Deok; Jo, Yun-Kyung; Jo, Nam-Ju

    2012-04-01

    Solid polymer electrolytes (SPEs) are an excellent alternative to liquid electrolytes due to their non-volatility, low toxicity, and high energy density. In this study, a SPE having the ion transport mechanism decoupled from segmental motion of a polymer based on poly(vinyl alcohol) (PVA) containing the salt lithium trifluoromethane sulfonate (LiCF3SO3, LiTf) has been prepared to overcome the low ionic conductivity of traditional SPEs at room temperature. PVA has a high glass transition temperature (358 K) and good mechanical properties, and despite being atactic, it can crystallize, especially if highly hydrolyzed. From an ac impedance analysis, it was found that the ionic conductivity of the PVA-based SPE increased with increasing salt concentration. In particular, a dramatic increase was observed between 40 and 50 wt% of salt. The ionic conduction mechanism of the PVA-based SPE is proposed based on intensive study using FT-IR spectroscopic measurements, XRD and AFM. Through measurements of linear sweep voltammetry (LSV) and cyclic voltammetry (CV), it is also found that the SPE with PVA and LiCF3SO3 has good electrochemical stability.

  16. Intermediate temperature single-chamber methane fed SOFC based on Gd doped ceria electrolyte and La 0.5Sr 0.5CoO 3- δ as cathode

    Science.gov (United States)

    Morales, M.; Piñol, S.; Segarra, M.

    Single-chamber fuel cells with electrodes supported on an electrolyte of gadolinium doped ceria Ce 1- xGd xO 2- y with x = 0.2 (CGO) 200 μm thickness has been successfully prepared and characterized. The cells were fed directly with a mixture of methane and air. Doped ceria electrolyte supports were prepared from powders obtained by the acetyl-acetonate sol-gel related method. Inks prepared from mixtures of precursor powders of NiO and CGO with different particle sizes and compositions were prepared, analysed and used to obtain optimal porous anodes thick films. Cathodes based on La 0.5Sr 0.5CoO 3 perovskites (LSCO) were also prepared and deposited on the other side of the electrolyte by inks prepared with a mixture of powders of LSCO, CGO and AgO obtained also by sol-gel related techniques. Both electrodes were deposited by dip coating at different thicknesses (20-30 μm) using a commercial resin where the electrode powders were dispersed. Finally, electrical properties were determined in a single-chamber reactor where methane, as fuel, was mixed with synthetic air below the direct combustion limit. Stable density currents were obtained in these experimental conditions. Temperature, composition and flux rate values of the carrier gas were determinants for the optimization of the electrical properties of the fuel cells.

  17. Actuator device utilizing a conductive polymer gel

    Science.gov (United States)

    Chinn, Douglas A.; Irvin, David J.

    2004-02-03

    A valve actuator based on a conductive polymer gel is disclosed. A nonconductive housing is provided having two separate chambers separated by a porous frit. The conductive polymer is held in one chamber and an electrolyte solution, used as a source of charged ions, is held in the second chamber. The ends of the housing a sealed with a flexible elastomer. The polymer gel is further provide with electrodes with which to apply an electrical potential across the gel in order to initiate an oxidation reaction which in turn drives anions across the porous frit and into the polymer gel, swelling the volume of the gel and simultaneously contracting the volume of the electrolyte solution. Because the two end chambers are sealed the flexible elastomer expands or contracts with the chamber volume change. By manipulating the potential across the gel the motion of the elastomer can be controlled to act as a "gate" to open or close a fluid channel and thereby control flow through that channel.

  18. Electrochemical energy storage in montmorillonite K10 clay based composite as supercapacitor using ionic liquid electrolyte.

    Science.gov (United States)

    Maiti, Sandipan; Pramanik, Atin; Chattopadhyay, Shreyasi; De, Goutam; Mahanty, Sourindra

    2016-02-15

    Exploring new electrode materials is the key to realize high performance energy storage devices for effective utilization of renewable energy. Natural clays with layered structure and high surface area are prospective materials for electrical double layer capacitors (EDLC). In this work, a novel hybrid composite based on acid-leached montmorillonite (K10), multi-walled carbon nanotube (MWCNT) and manganese dioxide (MnO2) was prepared and its electrochemical properties were investigated by fabricating two-electrode asymmetric supercapacitor cells against activated carbon (AC) using 1.0M tetraethylammonium tetrafluroborate (Et4NBF4) in acetonitrile (AN) as electrolyte. The asymmetric supercapacitors, capable of operating in a wide potential window of 0.0-2.7V, showed a high energy density of 171Whkg(-1) at a power density of ∼1.98kWkg(-1). Such high EDLC performance could possibly be linked to the acid-base interaction of K10 through its surface hydroxyl groups with the tetraethylammonium cation [(C2H5)4N(+) or TEA(+)] of the ionic liquid electrolyte. Even at a very high power density of 96.4kWkg(-1), the cells could still deliver an energy density of 91.1Whkg(-1) exhibiting an outstanding rate capability. The present study demonstrates for the first time, the excellent potential of clay-based composites for high power energy storage device applications.

  19. American Society of Nephrology quiz and questionnaire 2014: acid-base and electrolyte disorders.

    Science.gov (United States)

    Rosner, Mitchell H; Perazella, Mark A; Choi, Michael J

    2015-03-06

    The Nephrology Quiz and Questionnaire remains an extremely popular session for attendees of the Annual Kidney Week Meeting of the American Society of Nephrology. Once again, in 2014 the conference hall was overflowing with audience members and eager quiz participants. Topics covered by the expert discussants included electrolyte and acid-base disorders, glomerular disease, ESRD/dialysis, and transplantation. Complex cases from each of these categories along with single-best-answer questions were prepared and submitted by the panel of experts. Before the meeting, program directors of United States nephrology training programs and nephrology fellows answered the questions using an Internet-based questionnaire. During the live session, members of the audience tested their knowledge and judgment on a series of case-oriented questions prepared and discussed by the experts. They compared their answers in real time using audience response devices with the answers of the nephrology fellows and training program directors. The correct and incorrect answers were then discussed after the audience responses and the results of the questionnaire were displayed. As always, the audience, lecturers, and moderators enjoyed this educational session. This article recapitulates the acid-base and electrolyte disorders portion of the session and reproduces its educational value for the readers of the Clinical Journal of the American Society of Nephrology. Enjoy the clinical cases and expert discussions.

  20. Nanostructured lipid carriers (NLC) based topical gel of flurbiprofen: design, characterization and in vivo evaluation.

    Science.gov (United States)

    Han, Fei; Yin, Ran; Che, Xin; Yuan, Jing; Cui, Yanan; Yin, He; Li, Sanming

    2012-12-15

    Nanostructured lipid carriers (NLC)-based gel was developed as potential topical system for flurbiprofen (FP) topical delivery. The characterizations of the prepared semisolid formulation for topical application on skin were assessed by means of particle size distribution, zeta potential analysis, X-ray analysis, in vitro percutaneous penetration, rheological study, skin irritation test, in vivo pharmacodynamic evaluation and in vivo pharmacokinetic study. The NLC remained within the colloidal range and it was uniformly dispersed after suitably gelled by carbopol preparation. It was indicated in vitro permeation studies through rat skin that FP-NLC-gel had a more pronounced permeation profile compared with that of FP-loaded common gel. Pseudoplastic flows with thixotropy were obtained for all NLC-gels after storage at three different temperatures. No oedema and erythema were observed after administration of FP-NLC-gel on the rabbit skin, and the ovalbumin induced rat paw edema could be inhibited by the gel. The maximum concentration in plasma was 29.44 μg/ml and 2.49 μg/ml after oral and topical administration, respectively. While the amount of drug accumulated in skin after topical application was much higher than oral application. In conclusion, NLC-based gel could be a promising vehicle for topical delivery of FP. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. A High Temperature Electrochemical Energy Storage System Based on Sodium Beta-Alumina Solid Electrolyte (Base)

    Energy Technology Data Exchange (ETDEWEB)

    Anil Virkar

    2008-03-31

    This report summarizes the work done during the period September 1, 2005 and March 31, 2008. Work was conducted in the following areas: (1) Fabrication of sodium beta{double_prime} alumina solid electrolyte (BASE) using a vapor phase process. (2) Mechanistic studies on the conversion of {alpha}-alumina + zirconia into beta{double_prime}-alumina + zirconia by the vapor phase process. (3) Characterization of BASE by X-ray diffraction, SEM, and conductivity measurements. (4) Design, construction and electrochemical testing of a symmetric cell containing BASE as the electrolyte and NaCl + ZnCl{sub 2} as the electrodes. (5) Design, construction, and electrochemical evaluation of Na/BASE/ZnCl{sub 2} electrochemical cells. (6) Stability studies in ZnCl{sub 2}, SnCl{sub 2}, and SnI{sub 4} (7) Design, assembly and testing of planar stacks. (8) Investigation of the effect of porous surface layers on BASE on cell resistance. The conventional process for the fabrication of sodium ion conducting beta{double_prime}-alumina involves calcination of {alpha}-alumina + Na{sub 2}CO{sub 3} + LiNO{sub 3} at 1250 C, followed by sintering powder compacts in sealed containers (platinum or MgO) at {approx}1600 C. The novel vapor phase process involves first sintering a mixture of {alpha}-alumina + yttria-stabilized zirconia (YSZ) into a dense ceramic followed by exposure to soda vapor at {approx}1450 C to convert {alpha}-alumina into beta{double_prime}-alumina. The vapor phase process leads to a high strength BASE, which is also resistant to moisture attack, unlike BASE made by the conventional process. The PI is the lead inventor of the process. Discs and tubes of BASE were fabricated in the present work. In the conventional process, sintering of BASE is accomplished by a transient liquid phase mechanism wherein the liquid phase contains NaAlO{sub 2}. Some NaAlO{sub 2} continues to remain at grain boundaries; and is the root cause of its water sensitivity. In the vapor phase process, Na

  2. Towards A Model-Based Prognostics Methodology for Electrolytic Capacitors: A Case Study Based on Electrical Overstress Accelerated Aging

    Science.gov (United States)

    Celaya, Jose R.; Kulkarni, Chetan S.; Biswas, Gautam; Goebel, Kai

    2012-01-01

    A remaining useful life prediction methodology for electrolytic capacitors is presented. This methodology is based on the Kalman filter framework and an empirical degradation model. Electrolytic capacitors are used in several applications ranging from power supplies on critical avionics equipment to power drivers for electro-mechanical actuators. These devices are known for their comparatively low reliability and given their criticality in electronics subsystems they are a good candidate for component level prognostics and health management. Prognostics provides a way to assess remaining useful life of a capacitor based on its current state of health and its anticipated future usage and operational conditions. We present here also, experimental results of an accelerated aging test under electrical stresses. The data obtained in this test form the basis for a remaining life prediction algorithm where a model of the degradation process is suggested. This preliminary remaining life prediction algorithm serves as a demonstration of how prognostics methodologies could be used for electrolytic capacitors. In addition, the use degradation progression data from accelerated aging, provides an avenue for validation of applications of the Kalman filter based prognostics methods typically used for remaining useful life predictions in other applications.

  3. Ordered mesoporous tungsten suboxide counter electrode for highly efficient iodine-free electrolyte-based dye-sensitized solar cells.

    Science.gov (United States)

    Jeong, Inyoung; Jo, Changshin; Anthonysamy, Arockiam; Kim, Jung-Min; Kang, Eunae; Hwang, Jongkook; Ramasamy, Easwaramoorthi; Rhee, Shi-Woo; Kim, Jin Kon; Ha, Kyoung-Su; Jun, Ki-Won; Lee, Jinwoo

    2013-02-01

    A disulfide/thiolate (T(2)/T(-)) redox-couple electrolyte, which is a promising iodine-free electrolyte owing to its transparent and noncorrosive properties, requires alternative counter-electrode materials because conventional Pt shows poor catalytic activity in such an electrolyte. Herein, ordered mesoporous tungsten suboxide (m-WO(3-x)), synthesized by using KIT-6 silica as a hard template followed by a partial reduction, is used as a catalyst for a counter electrode in T(2)/T(-)-electrolyte-based dye-sensitized solar cells (DSCs). The mesoporous tungsten suboxide, which possesses interconnected pores of 4 and 20 nm, provides a large surface area and efficient electrolyte penetration into the m-WO(3-x) pores. In addition to the advantages conferred by the mesoporous structure, partial reduction of tungsten oxide creates oxygen vacancies that can function as active catalytic sites, which causes a high electrical conductivity because of intervalence charge transfer between the W(5+) and W(6+) ions. m-WO(3-x) shows a superior photovoltaic performance (79 % improvement in the power conversion efficiency) over Pt in the T(2)/T(-) electrolyte. The superior catalytic activity of m-WO(3-x) is investigated by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and Tafel polarization curve analysis.

  4. Network type sp3 boron-based single-ion conducting polymer electrolytes for lithium ion batteries

    Science.gov (United States)

    Deng, Kuirong; Wang, Shuanjin; Ren, Shan; Han, Dongmei; Xiao, Min; Meng, Yuezhong

    2017-08-01

    Electrolytes play a vital role in modulating lithium ion battery performance. An outstanding electrolyte should possess both high ionic conductivity and unity lithium ion transference number. Here, we present a facile method to fabricate a network type sp3 boron-based single-ion conducting polymer electrolyte (SIPE) with high ionic conductivity and lithium ion transference number approaching unity. The SIPE was synthesized by coupling of lithium bis(allylmalonato)borate (LiBAMB) and pentaerythritol tetrakis(2-mercaptoacetate) (PETMP) via one-step photoinitiated in situ thiol-ene click reaction in plasticizers. Influence of kinds and content of plasticizers was investigated and the optimized electrolytes show both outstanding ionic conductivity (1.47 × 10-3 S cm-1 at 25 °C) and high lithium transference number of 0.89. This ionic conductivity is among the highest ionic conductivity exhibited by SIPEs reported to date. Its electrochemical stability window is up to 5.2 V. More importantly, Li/LiFePO4 cells with the prepared single-ion conducting electrolytes as the electrolyte as well as the separator display highly reversible capacity and excellent rate capacity under room temperature. It also demonstrates excellent long-term stability and reliability as it maintains capacity of 124 mA h g-1 at 1 C rate even after 500 cycles without obvious decay.

  5. Flexible thin-film battery based on graphene-oxide embedded in solid polymer electrolyte

    Science.gov (United States)

    Kammoun, M.; Berg, S.; Ardebili, H.

    2015-10-01

    Enhanced safety of flexible batteries is an imperative objective due to the intimate interaction of such devices with human organs such as flexible batteries that are integrated with touch-screens or embedded in clothing or space suits. In this study, the fabrication and testing of a high performance thin-film Li-ion battery (LIB) is reported that is both flexible and relatively safer compared to the conventional electrolyte based batteries. The concept is facilitated by the use of solid polymer nanocomposite electrolyte, specifically, composed of polyethylene oxide (PEO) matrix and 1 wt% graphene oxide (GO) nanosheets. The flexible LIB exhibits a high maximum operating voltage of 4.9 V, high capacity of 0.13 mA h cm-2 and an energy density of 4.8 mW h cm-3. The battery is encapsulated using a simple lamination method that is economical and scalable. The laminated battery shows robust mechanical flexibility over 6000 bending cycles and excellent electrochemical performance in both flat and bent configurations. Finite element analysis (FEA) of the LIB provides critical insights into the evolution of mechanical stresses during lamination and bending.Enhanced safety of flexible batteries is an imperative objective due to the intimate interaction of such devices with human organs such as flexible batteries that are integrated with touch-screens or embedded in clothing or space suits. In this study, the fabrication and testing of a high performance thin-film Li-ion battery (LIB) is reported that is both flexible and relatively safer compared to the conventional electrolyte based batteries. The concept is facilitated by the use of solid polymer nanocomposite electrolyte, specifically, composed of polyethylene oxide (PEO) matrix and 1 wt% graphene oxide (GO) nanosheets. The flexible LIB exhibits a high maximum operating voltage of 4.9 V, high capacity of 0.13 mA h cm-2 and an energy density of 4.8 mW h cm-3. The battery is encapsulated using a simple lamination method

  6. Cobalt-Based Electrolytes for Dye-Sensitized Solar Cells: Recent Advances towards Stable Devices

    Directory of Open Access Journals (Sweden)

    Federico Bella

    2016-05-01

    Full Text Available Redox mediators based on cobalt complexes allowed dye-sensitized solar cells (DSCs to achieve efficiencies exceeding 14%, thus challenging the emerging class of perovskite solar cells. Unfortunately, cobalt-based electrolytes demonstrate much lower long-term stability trends if compared to the traditional iodide/triiodide redox couple. In view of the large-scale commercialization of cobalt-based DSCs, the scientific community has recently proposed various approaches and materials to increase the stability of these devices, which comprise gelling agents, crosslinked polymeric matrices and mixtures of solvents (including water. This review summarizes the most significant advances recently focused towards this direction, also suggesting some intriguing way to fabricate third-generation cobalt-based photoelectrochemical devices stable over time.

  7. A contrastive study of three graphite anodes in the piperidinium based electrolytes for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Xiao-Tao; Wang, Chen-Yi; Gao, Kun, E-mail: gaokun0451@163.com; Niu, Li-Li; Li, Shu-Dan, E-mail: lishudan0451@163.com

    2016-02-15

    Graphical abstract: The fitting results of R{sub sei} and R{sub ct} of three graphite/Li cells. Besides three graphite/Li cells show the similar R{sub sei}, the NG198/Li cell demonstrates a higher R{sub ct} value in all test temperatures. Especially, the R{sub ct} at 333 K is even up to 355.8 Ω cm{sup 2}. Obviously, the narrow distribution of edge plane for NG198 caused this result, and then greatly restricts its cell capacity. By contrast, CMB with bigger specific surface area and more Li{sup +} insertion points shows lower resistance at room temperature, which should help to improve its capacity. - Highlights: • SEI film is closely related to graphite structures and formation temperature. • The graphite with bigger surface area and more Li{sup +} insertion points behaves better. • The graphite with narrow edge plane is uncompetitive for ionic liquid electrolyte. - Abstract: The electrochemical behaviors of natural graphite (NG198), artificial graphite (AG360) and carbon microbeads (CMB) in an ionic liquid based electrolyte are investigated by cyclic voltammetry (CV). The surface and structure of three graphite materials are characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD) before and after cycling. It is found that solid electrolyte interface (SEI) is closely related to graphite structure. Benefiting from larger specific surface area and more dispersed Li{sup +} insertion points, CMB shows a better Li{sup +} insertion/de-insertion behavior than NG198 and AG360. Furthermore, electrochemical impedance spectra (EIS) prove that the SEI of different graphite electrodes has different intrinsic resistance and Li{sup +} penetrability. By comparison, CMB behaves better cell performances than AG360, while the narrow edge plane makes NG198 uncompetitive as a potential anode for the ionic liquids (ILs)-type Li-ion battery.

  8. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes

    Science.gov (United States)

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-01

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g−1carbon at 20 μA cm−2. Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g−1carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g−1carbon at 20 μA cm−2 and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage. PMID:28117359

  9. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes

    Science.gov (United States)

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-01

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g‑1carbon at 20 μA cm‑2. Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g‑1carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g‑1carbon at 20 μA cm‑2 and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage.

  10. α-Gel formation by amino acid-based gemini surfactants.

    Science.gov (United States)

    Sakai, Kenichi; Ohno, Kiyomi; Nomura, Kazuyuki; Endo, Takeshi; Sakamoto, Kazutami; Sakai, Hideki; Abe, Masahiko

    2014-07-08

    Ternary mixtures being composed of surfactant, long-chain alcohol, and water sometimes form a highly viscous lamellar gel with a hexagonal packing arrangement of their crystalline hydrocarbon chains. This molecular assembly is called "α-crystalline phase" or "α-gel". In this study, we have characterized α-gels formed by the ternary mixtures of amino acid-based gemini surfactants, 1-hexadecanol (C16OH), and water. The surfactants used in this study were synthesized by reacting dodecanoylglutamic acid anhydride with alkyl diamines and abbreviated as 12-GsG-12 (s: the spacer chain length of 2, 5, and 8 methylene units). An amino acid-based monomeric surfactant, dodecanoylglutamic acid (12-Glu), was also used for comparison. At a fixed water concentration the melting point of the α-gel increased with increasing C16OH concentration, and then attained a saturation level at the critical mole ratio of 12-GsG-12/C16OH = 1/2 under the normalization by the number of hydrocarbon chains of the surfactants. This indicates that, to obtain the saturated α-gel, a lesser amount of C16OH is required for the gemini surfactants than for the monomeric one (the critical mole ratio of 12-Glu/C16OH = 1/3). Small- and wide-angle X-ray scattering measurements demonstrated an increase in the long-range d-spacing of the saturated α-gels in the order 12-Glu gels at a given water concentration. This is caused by the decreased amount of excess water being present outside the α-gel structure (or the increased amount of water incorporated between the surfactant-alcohol bilayers). To the best of our knowledge, this is the first report focusing on the formation of α-gel in gemini surfactant systems.

  11. Complex impedance and conductivity of agar-based ion-conducting polymer electrolytes

    Science.gov (United States)

    Nwanya, A. C.; Amaechi, C. I.; Udounwa, A. E.; Osuji, R. U.; Maaza, M.; Ezema, F. I.

    2015-04-01

    Agar-based electrolyte standing films with different salts and weak acids as ion and proton conductors were prepared and characterized by X-ray diffraction, UV-visible spectrophotometry, photoluminescence emission spectroscopy and electrochemical impedance spectroscopy. The salts used are lithium perchlorate (LiClO4) and potassium perchlorate (KClO4), while the weak acids used are acetic acid (CH3COOH) and lactic acid (C3H6O3). The values of the ion conductivity obtained for the agar-based polymer films are 6.54 × 10-8, 9.12 × 10-8, 3.53 × 10-8, 2.24 × 10-8 S/cm for the agar/acetic acid, agar/lactic acid, agar/LiClO4 and agar/KClO4 polymer films, respectively. As a function of temperature, the ion conductivity exhibits an Arrhenius behavior and the estimated activation energy is ≈0.1 eV for all the samples. The samples depicted high values of dielectric permittivity toward low frequencies which is due mostly to electrode polarization effect. The samples showed very high transparency (85-98 %) in the visible region, and this high transparency is one of the major requirements for application in electrochromic devices (ECD). The values of conductivity and activation energy obtained indicate that the electrolytes are good materials for application in ECD.

  12. High-Efficiency Glass and Printable Flexible Dye-Sensitized Solar Cells with Water-Based Electrolytes

    Directory of Open Access Journals (Sweden)

    Omar Moudam

    2014-01-01

    Full Text Available The performance of a flexible and glass dye-sensitized solar cell (DSSC with water-based electrolyte solutions is described. High concentrations of alkylamidazoliums were used to overcome the deleterious effect of water and, based on this variable, pure water-based electrolyte DSSCs were tested displaying the highest recorded efficiency so far of 3.45% and 6% for flexible and glass cells, respectively, under a simulated air mass 1.5 solar spectrum illumination at 100 mWcm−2. An improvement in the Jsc with high water content and the positive impact of GuSCN on the enhancement of the performance of pure water-based electrolytes were also observed.

  13. A silica gel based method for extracting insect surface hydrocarbons.

    Science.gov (United States)

    Choe, Dong-Hwan; Ramírez, Santiago R; Tsutsui, Neil D

    2012-02-01

    Here, we describe a novel method for the extraction of insect cuticular hydrocarbons using silica gel, herein referred to as "silica-rubbing". This method permits the selective sampling of external hydrocarbons from insect cuticle surfaces for subsequent analysis using gas chromatography-mass spectrometry (GC-MS). The cuticular hydrocarbons are first adsorbed to silica gel particles by rubbing the cuticle of insect specimens with the materials, and then are subsequently eluted using organic solvents. We compared the cuticular hydrocarbon profiles that resulted from extractions using silica-rubbing and solvent-soaking methods in four ant and one bee species: Linepithema humile, Azteca instabilis, Camponotus floridanus, Pogonomyrmex barbatus (Hymenoptera: Formicidae), and Euglossa dilemma (Hymenoptera: Apidae). We also compared the hydrocarbon profiles of Euglossa dilemma obtained via silica-rubbing and solid phase microextraction (SPME). Comparison of hydrocarbon profiles obtained by different extraction methods indicates that silica rubbing selectively extracts the hydrocarbons that are present on the surface of the cuticular wax layer, without extracting hydrocarbons from internal glands and tissues. Due to its surface specificity, efficiency, and low cost, this new method may be useful for studying the biology of insect cuticular hydrocarbons.

  14. Xyloglucan Based In Situ Gel of Lidocaine HCl for the Treatment of Periodontosis

    Directory of Open Access Journals (Sweden)

    Ashlesha P. Pandit

    2016-01-01

    Full Text Available The present study was aimed at formulating thermoreversible in situ gel of local anesthetic by using xyloglucan based mucoadhesive tamarind seed polysaccharide (TSP into periodontal pocket. Temperature-sensitive in situ gel of lidocaine hydrochloride (LH (2% w/v was formulated by cold method. A full 32 factorial design was employed to study the effect of independent variables concentrations of Lutrol F127 and TSP to optimize in situ gel. The dependent variables evaluated were gelation temperature (Y1 and drug release (Y2. The results revealed the surface pH of 6.8, similar to the pH of saliva. Viscosity study showed the marked increase in the viscosity of gel at 37°C due to sol-gel conversion. TSP was found to act as good mucoadhesive component to retain gel at the site of application in dental pocket. Gelation of formulation occurred near to body temperature. In vitro study depicted the fast onset of drug action but lasting the release (90% till 2 h. Formulation F7 was considered as optimized batch, containing 18% Lutrol F127 and 1% tamarind seed polysaccharide. Thus, lidocaine hydrochloride thermoreversible in situ gel offered an alternative to painful injection therapy of anesthesia during dental surgery, with fast onset of anesthetic action lasting throughout the dental procedure.

  15. Xyloglucan Based In Situ Gel of Lidocaine HCl for the Treatment of Periodontosis.

    Science.gov (United States)

    Pandit, Ashlesha P; Pol, Vaibhav V; Kulkarni, Vinit S

    2016-01-01

    The present study was aimed at formulating thermoreversible in situ gel of local anesthetic by using xyloglucan based mucoadhesive tamarind seed polysaccharide (TSP) into periodontal pocket. Temperature-sensitive in situ gel of lidocaine hydrochloride (LH) (2% w/v) was formulated by cold method. A full 3(2) factorial design was employed to study the effect of independent variables concentrations of Lutrol F127 and TSP to optimize in situ gel. The dependent variables evaluated were gelation temperature (Y 1) and drug release (Y 2). The results revealed the surface pH of 6.8, similar to the pH of saliva. Viscosity study showed the marked increase in the viscosity of gel at 37°C due to sol-gel conversion. TSP was found to act as good mucoadhesive component to retain gel at the site of application in dental pocket. Gelation of formulation occurred near to body temperature. In vitro study depicted the fast onset of drug action but lasting the release (90%) till 2 h. Formulation F7 was considered as optimized batch, containing 18% Lutrol F127 and 1% tamarind seed polysaccharide. Thus, lidocaine hydrochloride thermoreversible in situ gel offered an alternative to painful injection therapy of anesthesia during dental surgery, with fast onset of anesthetic action lasting throughout the dental procedure.

  16. Xyloglucan Based In Situ Gel of Lidocaine HCl for the Treatment of Periodontosis

    Science.gov (United States)

    Pandit, Ashlesha P.; Pol, Vaibhav V.; Kulkarni, Vinit S.

    2016-01-01

    The present study was aimed at formulating thermoreversible in situ gel of local anesthetic by using xyloglucan based mucoadhesive tamarind seed polysaccharide (TSP) into periodontal pocket. Temperature-sensitive in situ gel of lidocaine hydrochloride (LH) (2% w/v) was formulated by cold method. A full 32 factorial design was employed to study the effect of independent variables concentrations of Lutrol F127 and TSP to optimize in situ gel. The dependent variables evaluated were gelation temperature (Y1) and drug release (Y2). The results revealed the surface pH of 6.8, similar to the pH of saliva. Viscosity study showed the marked increase in the viscosity of gel at 37°C due to sol-gel conversion. TSP was found to act as good mucoadhesive component to retain gel at the site of application in dental pocket. Gelation of formulation occurred near to body temperature. In vitro study depicted the fast onset of drug action but lasting the release (90%) till 2 h. Formulation F7 was considered as optimized batch, containing 18% Lutrol F127 and 1% tamarind seed polysaccharide. Thus, lidocaine hydrochloride thermoreversible in situ gel offered an alternative to painful injection therapy of anesthesia during dental surgery, with fast onset of anesthetic action lasting throughout the dental procedure. PMID:27034908

  17. FORMULATION AND EVALUATION OF FLOATING IN SITU GEL BASED GASTRO RETENTIVE DRUG DELIVERY OF CIMETIDINE

    Directory of Open Access Journals (Sweden)

    Bhargav D. Jayswal

    2012-05-01

    Full Text Available The present investigation deals with the formulation and evaluation of sodium alginate and pectin basedIn situ gel of Cimetidine. Sodium alginate and pectin were used as a polymer and CaCO3 was used as across-linking agent. In-situ forming polymeric formulations drug delivery systems is in sol form beforeadministration in the body, but once administered, undergoes gelation in-situ to form a gel. Theformulation of gel depends upon factors like temperature modulation, pH changes, presence of ions andultra-violet irradiation, from which drug gets released in sustained and controlled manner. The objectiveof this study was to develop a novel in- situ gel system for sustained drug delivery using naturalbiodegradable polymers. The system utilizes polymers that exhibit sol-to-gel phase transition due tochange in specific physico-chemical parameters. In-situ gel was formed at a biological pH. In vitrorelease studies were conducted in simulated gastric fluid and cumulative amount of drug release wasanalyzed by spectrophotometry. From designed set of experiments, it was evident that formulationcontaining 1.2% of sodium alginate and 1.5% of pectin control the release of drug for longer duration.The in-situ gel exhibited the expected, viscosity, drug content, pH, in vitro gelling capacity, in vitrofloating ability, water uptake ability and sustained drug release.The drug release from the in situ gelsfollows the fickian diffusion type of release.

  18. Fluid, electrolyte, and acid-base balances in three-day, combined-training horses.

    Science.gov (United States)

    White, S L

    1998-04-01

    Horses competing in 3-day, combined-training events develop a metabolic acidosis that is partially compensated for by a respiratory alkalosis immediately after phases B and D. By the end of phase C and 30 minutes to 2 hours after phase D, the acidosis is resolved by the oxidation of lactate, and a metabolic alkalosis prevails. A reduction in TBW and cation content occurs, which often is not replenished 12 to 24 hours after the event, even though the serum or plasma concentration of various constituents may be within normal limits. Hypochloremia and hypocalcemia, however, may persist 12 or more hours after the speed and endurance test. All of the data cited in this article are from horses that successfully completed their respective tests. Nevertheless, some horses developed substantial fluid and cation losses. In horses that are not well conditioned or in competitions in which terrain, footing, or hot environments increase the thermal load or decrease heat loss, greater losses of fluids and electrolytes can be expected. Body weight losses exceeding 5% and cation losses exceeding 4000 mEq/L occur in endurance horses suffering from exhaustion and synchronous diaphragmatic flutter. In one study, two thirds of the Na+ lost during exercise-induced sweating in cool, dry conditions was replenished from salt supplements added to a balanced forage and concentrated diet. Consequently, horses in regular training and competition may benefit from salt supplementation. The composition of the salt supplement and the amount fed should be based on the composition of the horse's diet, degree of work, and environmental conditions. Horses competing in a 3-day, combined-training event may be expected to have persistent losses of weight and cations, particularly if conditions result in heavy sweating. Many horses in the field studies had minimal changes in weight and cation balance compared with pre-event values. The diet and electrolyte supplementation of the horses in the majority of

  19. Polymer Electrolyte Membrane Electrolyzers Utilizing Non-precious Mo-based Hydrogen Evolution Catalysts.

    Science.gov (United States)

    Ng, Jia Wei Desmond; Hellstern, Thomas R; Kibsgaard, Jakob; Hinckley, Allison C; Benck, Jesse D; Jaramillo, Thomas F

    2015-10-26

    The development of low-cost hydrogen evolution reaction (HER) catalysts that can be readily integrated into electrolyzers is critical if H2 from renewable electricity-powered electrolysis is to compete cost effectively with steam reforming. Herein, we report three distinct earth-abundant Mo-based catalysts, namely those based on MoSx , [Mo3 S13 ](2-) nanoclusters, and sulfur-doped Mo phosphide (MoP|S), loaded onto carbon supports. The catalysts were synthesized through facile impregnation-sulfidization routes specifically designed for catalyst-device compatibility. Fundamental electrochemical studies demonstrate the excellent HER activity and stability of the Mo-sulfide based catalysts in an acidic environment, and the resulting polymer electrolyte membrane (PEM) electrolyzers that integrate these catalysts exhibit high efficiency and durability. This work is an important step towards the goal of replacing Pt with earth-abundant catalysts for the HER in commercial PEM electrolyzers.

  20. Nanoemulsion-based gel formulation of diclofenac diethylamine: design, optimization, rheological behavior and in vitro diffusion studies.

    Science.gov (United States)

    Hamed, Rania; Basil, Marwa; AlBaraghthi, Tamadur; Sunoqrot, Suhair; Tarawneh, Ola

    2016-12-01

    Chronic oral administration of the non-steroidal anti-inflammatory drug, diclofenac diethylamine (DDEA), is often associated with gastrointestinal ulcers and bleeding. As an alternative to oral administration, a nanoemulsion-based gel (NE gel) formulation of DDEA was developed for topical administration. An optimized formulation for the o/w nanoemulsion of oil, surfactant and cosurfactant was selected based on nanoemulsion mean droplet size, clarity, stability, and flowability, and incorporated into the gelling agent Carbopol® 971P. Rheological studies of the DDEA NE gel were conducted and compared to those of conventional DDEA gel and emulgel. The three gels exhibited an elastic behavior, where G' dominated G″ at all frequencies, indicating the formation of strong gels. NE gel exhibited higher G' values than conventional gel and emulgel, which indicated the formation of a stronger gel network. Strat-M® membrane, a synthetic membrane with diffusion characteristics that are well correlated to human skin, was used for the in vitro diffusion studies. The release of DDEA from conventional gel, emulgel and NE gel showed a controlled release pattern over 12 h, which was consistent with the rheological properties of the gels. DDEA release kinetics from the three gels followed super case II transport as fitted by Korsmeyer-Peppas model.

  1. New normoxic N-(Hydroxymethyl)acrylamide based polymer gel for 3D dosimetry in radiation therapy.

    Science.gov (United States)

    Rabaeh, Khalid A; Basfar, Ahmed A; Almousa, Akram A; Devic, Slobodan; Moftah, Belal

    2017-01-01

    A novel composition of normoxic polymer gel dosimeters based on radiation-induced polymerization of N-(Hydroxymethyl)acrylamide (NHMA) is introduced in this study for 3D dosimetry for Quality Assurance (QA) in radiation therapy. Dosimeters were irradiated by 6, 10 and 18MV photon beams of a medical linear accelerator at various dose rates to doses of up to 20Gy. The dose response of polymer gel dosimeters was studied using nuclear magnetic resonance (NMR) spin-spin relaxation rate (R2) of hydrogen protons within the water molecule. Also, we measured gel response using absorption spectroscopy and found that this novel gel can be successfully utilized for both MRI- and OCT- (Optical Computed Tomography) based 3D dosimetry. We investigated dosimetric properties of six different compositions of the new NHMA-based gel in terms of dose rate, radiation beam quality and stability of dose-dependent polymerization after irradiation. We found no significant effects of these parameters on the novel gel dosimeter performance in both relaxation rate and absorbance measurements.

  2. Effects of a new intravenous electrolyte solution for veterinary therapy on the electrolyte and acid-base balances of healthy horses

    Directory of Open Access Journals (Sweden)

    Priscilla Fajardo Valente Pereira

    2016-01-01

    Full Text Available ABSTRACT: The effects of a new intravenous electrolyte solution for veterinary therapy on electrolyte and acid-base balances of horses were evaluated, assessing the potential of the use of this solution as a rational alternative in fluid therapy. Eight healthy adult horses, including 4 males and 4 females, received two treatments in a cross-over design: isotonic saline solution (IS and a test solution (TS containing 145mEq of Na+, 5mEq of K+, 4mEq of Ca++, 2mEq of Mg++, 96mEq of Cl-, 60mEq of lactate, 50g of dextrose, and 4mg of cyanocobalamin per liter. Solutions were IV infused in a volume corresponding to 5% of BW, over 3 hours. Venous blood samples were taken 5 times before and after the infusion (at 0, 3, 6, 9 e 24h, for pHv, pCO2v, HCO3 -v, BEv, Na+, K+, Cl-, Ca++, Ca, P, Mg, glucose and L-lactate measurements, and AG and SID calculations. The data were analyzed through repeated measures ANOVA. The IS caused mild acidifying effect by increasing Cl- and decreasing plasma SID. In contrast, the TS induced mild and transient hypochloremia without changes in acid-base balance. Hyperglycemia was present at the end of the TS infusion and reversed 6 hours later. The horses did not exhibit any clinical changes. We concluded that TS is an option for fluid therapy in horses.

  3. Delayed recovery due to exaggerated acid, base and electrolyte imbalance in prolonged laparoscopic repair of diaphragmatic hernia

    Directory of Open Access Journals (Sweden)

    Rakesh Garg

    2011-01-01

    Full Text Available The acid, base and electrolyte changes are usually observed in the perioperative settings. We report a case of prolonged laparoscopic repair of left-sided diaphragmatic hernia which involved a lot of tissue handling and fluid replacement leading to acid, base and electrolyte imbalance. A 42-year-old male underwent prolonged laparoscopic repair under general anesthesia. Intraoperatively, surgeon reported that contents of hernia includes bowel along with mesentery, spleen and lot of fatty tissue The blood loss was about 2 L which was replaced with 1 L of colloid and 7.5 L of lactated ringer. Near the end of surgery arterial blood gas analysis revealed metabolic acidosis, hyperkalemia, and hypocalcemia leading to delayed recovery. We conclude prolonged laparoscopic surgery involving lot of tissue handling including gut and fat should be monitored for acid, base, electrolyte imbalance and corrected timely to have uneventful rapid recovery.

  4. Study of carbamate-modified disiloxane in porous PVDF-HFP membranes: new electrolytes/separators for lithium-ion batteries.

    Science.gov (United States)

    Jeschke, Steffen; Mutke, Monika; Jiang, Zhongxiang; Alt, Burkhard; Wiemhöfer, Hans-Dieter

    2014-06-23

    A gel electrolyte membrane is obtained through the absorption of a carbamate-modified liquid disiloxane-containing lithium bis(trifluoromethane)sulfonimide (LiTFSI) by using macroporous poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) membranes. The porous membranes are prepared by means of a phase inversion technique. The resulting gel electrolyte membrane is studied by using differential scanning calorimetry, Fourier-transform infrared (FTIR) spectroscopy, and microscope mapping through coherent anti-Stokes Raman scattering (CARS) confocal microscopy and impedance spectroscopy. The ionic conductivity of the gel electrolyte is 10(-4) S cm(-1) at 20 °C. FTIR spectroscopy reveals interactions between LiTFSI and the carbonyl moiety of the disiloxane. No interactions between LiTFSI and PVDF-HFP or between disiloxane and PVDF-HFP are detected by FTIR spectroscopy. Furthermore, the distribution of the α and β/γ phases of PVDF-HFP and the homogeneous distribution of disiloxane/LiTFSI in the gel electrolyte membranes are examined by FTIR mapping. CARS confocal microscopy is used to image the three-dimensional interconnectivity, which reveals a reticulated structure of macrovoids in the porous PVDF-HFP framework. Owing to properties such as electrochemical and thermal stability of the disiloxane-based liquid electrolyte and the mechanical stability of the porous PVDF-HFP membrane, the gel electrolyte membranes presented herein are promising candidates for applications as electrolytes/separators in lithium-ion batteries.

  5. Proton conducting sodium alginate electrolyte laterally coupled low-voltage oxide-based transistors

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yang Hui; Wan, Qing, E-mail: wanqing@nju.edu.cn [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); School of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China); Qiang Zhu, Li, E-mail: lqzhu@nimte.ac.cn [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Shi, Yi [School of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China)

    2014-03-31

    Solution-processed sodium alginate electrolyte film shows a high proton conductivity of ∼5.5 × 10{sup −3} S/cm and a high lateral electric-double-layer (EDL) capacitance of ∼2.0 μF/cm{sup 2} at room temperature with a relative humidity of 57%. Low-voltage in-plane-gate indium-zinc-oxide-based EDL transistors laterally gated by sodium alginate electrolytes are fabricated on glass substrates. The field-effect mobility, current ON/OFF ratio, and subthreshold swing of such EDL transistors are estimated to be 4.2 cm{sup 2} V{sup −1} s{sup −1}, 2.8 × 10{sup 6}, and 130 mV/decade, respectively. At last, a low-voltage driven resistor-load inverter is also demonstrated. Such in-plane-gate EDL transistors have potential applications in portable electronics and low-cost biosensors.

  6. Electrochemical oxidation of organic carbonate based electrolyte solutions at lithium metal oxide electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Imhof, R.; Novak, P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    The oxidative decomposition of carbonate based electrolyte solutions at practical lithium metal oxide composite electrodes was studied by differential electrochemical mass spectrometry. For propylene carbonate (PC), CO{sub 2} evolution was detected at LiNiO{sub 2}, LiCoO{sub 2}, and LiMn{sub 2}O{sub 4} composite electrodes. The starting point of gas evolution was 4.2 V vs. Li/Li{sup +} at LiNiO{sub 2}, whereas at LiCoO{sub 2} and LiMn{sub 2}O{sub 4}, CO{sub 2} evolution was only observed above 4.8 V vs. Li/Li{sup +}. In addition, various other volatile electrolyte decomposition products of PC were detected when using LiCoO{sub 2}, LiMn{sub 2}O4, and carbon black electrodes. In ethylene carbonate / dimethyl carbonate, CO{sub 2} evolution was only detected at LiNiO{sub 2} electrodes, again starting at about 4.2 V vs. Li/Li{sup +}. (author) 3 figs., 2 refs.

  7. Effect of Eutectic Concentration on Conductivity in PEO:LiX Based Solid Polymer Electrolytes

    Science.gov (United States)

    Zhan, Pengfei; Ganapatibhotla, Lalitha; Maranas, Janna

    Polyethylene oxide (PEO) and lithium salt based solid polymer electrolytes (SPEs) have been widely proposed as a substitution for the liquid electrolyte in Li-ion batteries. As salt concentration varies, these systems demonstrate rich phase behavior. Conductivity as a function of salt concentration has been measured for decades and various concentration dependences have been observed. A PEO:LiX mixture can have one or two conductivity maximums, while some mixtures with salt of high ionic strength will have higher conductivity as the salt concentration decrease. The factors that affect the conductivity are specific for each sample. The universal factor that affects conductivity is still not clear. In this work, we measured the conductivity of a series of PEO:LiX mixtures and statistical analysis shows conductivity is affected by the concentration difference from the eutectic concentration (Δc). The correlation with Δc is stronger than the correlation with glass transition temperature. We believe that at the eutectic concentration, during the solidification process, unique structures can form which aid conduction. Currently at Dow Chemical.

  8. An Investigation on the Properties of Palm-Based Polyurethane Solid Polymer Electrolyte

    Directory of Open Access Journals (Sweden)

    Farah Nadia Daud

    2014-01-01

    Full Text Available Palm-based polyurethane electrolyte was prepared via prepolymerization method between palm kernel oil polyol (PKO-p and 2,4′-diphenylmethane diisocyanate (MDI in acetone at room temperature with the presence of lithium trifluoromethanesulfonate (LiCF3SO3. The effect of varying the concentration of LiCF3SO3 salt on the ionic conductivity, chemical interaction, and structural and morphological properties of the polyurethane solid polymer electrolyte was investigated. The produced film was analyzed using electrochemical impedance spectroscopy (EIS, attenuated total reflection Fourier transform infrared (ATR-FTIR, X-ray diffraction (XRD, and scanning electron microscopy (SEM. The EIS result showed that the highest ionic conductivity was at 30 wt% LiCF3SO3 with a value of 1.6 × 10−5 S·cm−1. Infrared analysis showed the interaction between lithium ions and amine group (–N–H at (3600–3100 cm−1, carbonyl group (–C=O at (1750–1650 cm−1, and ether group (–C–O–C– at (1150–1000 cm−1 of the polyurethane forming polymer-salt complexes. The XRD result proved that LiCF3SO3 salt completely dissociates within the polyurethane film as no crystalline peaks of LiCF3SO3 were observed. The morphological study revealed that the films prepared have a good homogeneity and compatibility as no phase separation occurred.

  9. Studies on MgNi-Based Metal Hydride Electrode with Aqueous Electrolytes Composed of Various Hydroxides

    Directory of Open Access Journals (Sweden)

    Jean Nei

    2016-08-01

    Full Text Available Compositions of MgNi-based amorphous-monocrystalline thin films produced by radio frequency (RF sputtering with a varying composition target have been optimized. The composition Mg52Ni39Co3Mn6 is identified to possess the highest initial discharge capacity of 640 mAh·g−1 with a 50 mA·g−1 discharge current density. Reproduction in bulk form of Mg52Ni39Co3Mn6 alloy composition was prepared through a combination of melt spinning (MS and mechanical alloying (MA, shows a sponge-like microstructure with >95% amorphous content, and is chosen as the metal hydride (MH alloy for a sequence of electrolyte experiments with various hydroxides including LiOH, NaOH, KOH, RbOH, CsOH, and (C2H54N(OH. The electrolyte conductivity is found to be closely related to cation size in the hydroxide compound used as 1 M additive to the 4 M KOH aqueous solution. The degradation performance of Mg52Ni39Co3Mn6 alloy through cycling demonstrates a strong correlation with the redox potential of the cation in the alkali hydroxide compound used as 1 M additive to the 5 M KOH aqueous solution. NaOH, CsOH, and (C2H54N(OH additions are found to achieve a good balance between corrosion and conductivity performances.

  10. Evaluation of chitosan based vaginal bioadhesive gel formulations for antifungal drugs

    Directory of Open Access Journals (Sweden)

    Şenyiğit Zeynep Ay

    2014-06-01

    Full Text Available The aim of the present study was to evaluate chitosan as a vaginal mucoadhesive gel base for econazole nitrate and miconazole nitrate. To this aim, different types of chitosan with different molecular masses and viscosity properties [low molecular mass chitosan (viscosity: 20,000 mPa s, medium molecular mass chitosan (viscosity: 200,000 mPa s, high molecular mass chitosan (viscosity: 800,000 mPa s] have been used. First, rheological studies were conducted on chitosan gels. Mechanical, syringeability and mucoadhesive properties of chitosan gels were determined. Release profiles of econazole nitrate and miconazole nitrate from chitosan gels were obtained and evaluated kinetically. In addition, anticandidal activities of formulations were determined. Finally, vaginal retention of chitosan gels in rats was evaluated by in vivo distribution studies. Based on the results, it can be concluded that gels prepared with medium molecular mass chitosan might be effectively used for different antifungal agents in the treatment of vaginal candidiosis, since it has high mucoadhesiveness, suitable mechanical and release properties with good vaginal retention

  11. Kinetic factors determining conducting filament formation in solid polymer electrolyte based planar devices.

    Science.gov (United States)

    Krishnan, Karthik; Aono, Masakazu; Tsuruoka, Tohru

    2016-08-01

    Resistive switching characteristics and conducting filament formation dynamics in solid polymer electrolyte (SPE) based planar-type atomic switches, with opposing active Ag and inert Pt electrodes, have been investigated by optimizing the device configuration and experimental parameters such as the gap distance between the electrodes, the salt inclusion in the polymer matrix, and the compliance current applied in current-voltage measurements. The high ionic conductivities of SPE enabled us to make scanning electron microscopy observations of the filament formation processes in the sub-micrometer to micrometer ranges. It was found that switching behaviour and filament growth morphology depend strongly on several kinetic factors, such as the redox reaction rate at the electrode-polymer interfaces, ion mobility in the polymer matrix, electric field strength, and the reduction sites for precipitation. Different filament formations, resulting from unidirectional and dendritic growth behaviours, can be controlled by tuning specified parameters, which in turn improves the stability and performance of SPE-based devices.

  12. Ionic liquids based on S-alkylthiolanium cations and TFSI anion as potential electrolytes

    Institute of Scientific and Technical Information of China (English)

    ZHANG HuanQi; YANG Li; FANG ShaoHua; PENG ChengXin; LUO HongJun

    2009-01-01

    New ionic liquids based on S-alkylthiolanium cations with TFSI anions were synthesized and charac-terized.The physical and electrochemical properties,including melting point,thermal stability,solubil-ity,viscosity,conductivity and electrochemical window,were reported.Relation between these proper-ties and the structure of the cations was discussed.In this series,T4TFSI and T5TFSI have melting points below -60℃,and their conductivities are 2.10 mS/cm and 1.46 mS/cm;their electrochemical windows are 4.1 V and 4.5 V at room temperature.These cyclic alkylthiolanium-based ionic liquids are promising as novel electrolytes in various electrochemical devices,especially under low temperature condition.

  13. Ionic limiting molar conductivity calculation of Li-ion battery electrolyte based on mode coupling theory.

    Science.gov (United States)

    He, Xiangming; Pu, Weihua; Han, Jingli; Chen, Jian; Lu, Jiufang; Jiang, Changyin; Wan, Chunrong

    2005-12-15

    A method is proposed based on mode coupling theory in which the ion transference number is introduced into the theory. The ionic limiting molar conductivities of LiPF6, LiClO4, LiBF4, LiCF3SO3, Li(CF3SO3)2N, LiC4F9SO3, and LiAsF6 in PC(propylene carbonate), GBL(gamma-butyrolactone), PC(propylene carbonate)/EMC(ethylmethyl carbonate), and PC(propylene carbonate)/DME(dimethoxyethane) are calculated based on this method, which does not involve any adjustable parameter. The results fit well to the literature data which are calculated by an empirically adjusted formula. This presents a potential way to calculate the conductivities of Li-ion battery electrolytes.

  14. Non-volatile polymer electrolyte based on poly(propylene carbonate), ionic liquid, and lithium perchlorate for electrochromic devices.

    Science.gov (United States)

    Zhou, Dan; Zhou, Rui; Chen, Chuanxiang; Yee, Wu-Aik; Kong, Junhua; Ding, Guoqiang; Lu, Xuehong

    2013-06-27

    A series of solvent-free ionic liquid (IL)-based polymer electrolytes composed of amorphous and biodegradable poly(propylene carbonate) (PPC) host, LiClO4, and 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM(+)BF4(-)) were prepared and characterized for the first time. FTIR studies reveal that the interaction between PPC chains and imidazolium cations weakens the complexation between PPC chains and Li(+) ions. Thermal analysis (DSC and TGA) results show that the incorporation of BMIM(+)BF4(-) into PPC/LiClO4 remarkably decreases the glass transition temperature and improves the thermal stability of the electrolytes. AC impedance results show that the ionic conductivities of the electrolytes are significantly increased with the increase of BMIM(+)BF4(-) amount, the ambient ionic conductivity of the electrolyte at a PPC/LiClO4/BMIM(+)BF4(-) weight ratio of 1/0.2/3 is 1.5 mS/cm, and the ionic transport behavior follows the Arrhenius equation. Both PPC/LiClO4/BMIM(+)BF4(-) and PPC/BMIM(+)BF4(-) electrolytes were applied in electrochromic devices with polyaniline as the electrochromic layer. The PPC/LiClO4/BMIM(+)BF4(-)-based device exhibits much better electrochromic performance in terms of optical contrast and switching time due to the presence of much smaller cations.

  15. Novel choline-based ionic liquids as safe electrolytes for high-voltage lithium-ion batteries

    Science.gov (United States)

    Yong, Tianqiao; Zhang, Lingzhi; Wang, Jinglun; Mai, Yongjin; Yan, Xiaodan; Zhao, Xinyue

    2016-10-01

    Three choline-based ionic liquids functionalized with trimethylsilyl, allyl, and cynoethyl groups are synthesized in an inexpensive route as safe electrolytes for high-voltage lithium-ion batteries. The thermal stabilities, viscosities, conductivities, and electrochemical windows of these ILs are reported. Hybrid electrolytes were formulated by doping with 0.6 M LiPF6/0.4 M lithium oxalydifluoroborate (LiODFB) as salts and dimethyl carbonate (DMC) as co-solvent. By using 0.6 M LiPF6/0.4 M LiODFB trimethylsilylated choline-based IL (SN1IL-TFSI)/DMC as electrolyte, LiCoO2/graphite full cell showed excellent cycling performance with a capacity of 152 mAh g-1 and 99% capacity retention over 90 cycles at a cut-off voltage of 4.4 V. The propagation rate of SN1IL-TFSI)/DMC electrolyte is only one quarter of the commercial electrolyte (1 M LiPF6 EC/DEC/DMC, v/v/v = 1/1/1), suggesting a better safety feature.

  16. Development and Evaluation of a Multimedia e-Learning Resource for Electrolyte and Acid-Base Disorders

    Science.gov (United States)

    Davids, Mogamat Razeen; Chikte, Usuf M. E.; Halperin, Mitchell L.

    2011-01-01

    This article reports on the development and evaluation of a Web-based application that provides instruction and hands-on practice in managing electrolyte and acid-base disorders. Our teaching approach, which focuses on concepts rather than details, encourages quantitative analysis and a logical problem-solving approach. Identifying any dangers to…

  17. Influence of silver ion reduction on electrical modulus parameters of solid polymer electrolyte based on chitosan-silver triflate electrolyte membrane

    Directory of Open Access Journals (Sweden)

    2010-05-01

    Full Text Available The electric modulus properties of solid polymer electrolyte based on chitosan: AgCF3SO3 from 303 to 393 K have been investigated by using impedance spectroscopy. The shift of the M'' peak spectra with frequeny depends on the dissociation and association of ions. The lowest conductivity relaxation time τσ, was found for the sample with the highest conductivity. The real part of electrical modulus shows that the material is highly capacitive. The asymmetric peak of the imaginary part of electric modulus M'', predicts a non Debye type relaxation. The distribution of relaxation times was indicated by a deformed arc form of Argand plot. The increase of M' and M'' values above 358 K can be attributed to the transformation of silver ions to silver nanoparticles. The complex impedance plots and ultraviolet-visible (UV-vis absorption spectroscopy indicate the temperature dependent of silver nanoparticles in chitosan-silver triflate solid electrolyte. The formation of silver nanoparticles was confirmed by transmission electron microscopy (TEM. The scaling behavior of M'' spectra shows that the dynamical relaxation processes is temperature independent for aparticular composition. The β exponent value indicate that the conductivity relaxation is highly non exponential.

  18. Lithium Polymer Electrolytes Based On PMMA / PEG And Penetrant Diffusion In Kraton Penta-Block Ionomer

    Science.gov (United States)

    Meng, Yan

    The study of diffusion in polymeric material is critical to many research fields and applications, such as polymer morphology, protective coatings (paints and varnishes), separation membranes, transport phenomena, polymer electrolytes, polymer melt, and controlled release of drugs from polymer carriers [1-9]. However, it is still a challenge to understand, predict and control the diffusion of molecules and ions of different sizes in polymers [2]. This work studied the medium to long range diffusion of species (i.e., ions and molecules) in solid polymer electrolytes based on poly(ethylene glycol)/poly(methyl methacrylate) (PEG/PMMA) for Li-based batteries, and polymeric permselective membranes via pulsed-field gradient NMR and a.c. impedance. Over the past decades polymer electrolytes have attracted much attention because of their promising technological application as an ion-conducting medium in solid-state batteries, fuel cells, electrochromic displays, and chemical sensors [10, 11]. However, despite numerous studies related to ionic transport in these electrolytes the understanding of the migration mechanism is still far from being complete, and progress in the field remains largely empirical [10, 12-15]. Among various candidates for solid polymer electrolyte (SPE) material, the miscible polymer pair, poly(ethylene oxide)/poly(methyl methacrylate) (PEO/PMMA), is an attractive one, because there is a huge difference in mobility between PEO and PMMA in their blends, and PEO chains remain exceptionally mobile in the blend even at temperature below the glass transition temperature of the blend [ 16]. Thus the mechanical strength and dimensional stability is maintained by PMMA component, while the chain motions or rearrangements of the PEO component virtually contribute to the ion transport [17]. The current work prepared two types of SPE based on poly(ethylene glycol) (PEG) /PMMA (40/60 by weight) for Li-based batteries: lithium bis(trifluoromethylsulfonylimide) (Li

  19. A novel energy absorber based on magnetorheological gel

    Science.gov (United States)

    Pang, Haoming; Xuan, Shouhu; Sun, Chuanlin; Gong, Xinglong

    2017-10-01

    In this work, a novel magnetorheological energy absorber (MREA) was designed by using magnetorheological gel (MRG) as the damping medium. The proposed MREA had tunable piston gap distances and variable inner magnetic flux density distribution. The piston gap distance could be varied from 7–2 mm and the magnetic flux density at the gap increased from 120–860 mT, respectively. Under both low velocity compression and high speed impact, the damping could be divided into three parts. In the impact test, the velocity of a drop hammer could be reduced from to 3.4–0 m s‑1 within a very short time (13 ms) and distance (17 mm). The maximum damping force of the MREA reached to as high as 8 kN. The damping force could also be adjusted by changing the current input. Under a 2 A current, the energy absorption ratio increased about 23% (from 4.13–5.07 J mm‑1).

  20. Mg/O2 Battery Based on the Magnesium-Aluminum Chloride Complex (MACC) Electrolyte

    DEFF Research Database (Denmark)

    Vardar, Galin; Smith, Jeffrey G.; Thomson, Travis

    2016-01-01

    rechargeability in these systems is severely limited. The Mg/O2-MACC/DME discharge product comprises a mixture of Mg(ClO4)2 and MgCl2, with the latter likely formed from slow decomposition of the former. The presence of Cl in these compounds suggests that the electrolyte participates in the cell reaction...... or reacts readily with the initial electrochemical products. A rate study suggests that O2 diffusion in the electrolyte limits discharge capacities at higher currents. Formation of an insulating product film on the positive electrodes of Mg/O2-MACC/DME cells following deep discharge increases cell impedance......Mg/O2 cells employing a MgCl2/AlCl3/DME (MACC/DME) electrolyte are cycled and compared to cells with modified Grignard electrolytes, showing that performance of magnesium/oxygen batteries depends strongly on electrolyte composition. Discharge capacity is far greater for MACC/DME-based cells, while...

  1. Conformal, Nanoscale ZnO Surface Modification of Garnet-Based Solid-State Electrolyte for Lithium Metal Anodes.

    Science.gov (United States)

    Wang, Chengwei; Gong, Yunhui; Liu, Boyang; Fu, Kun; Yao, Yonggang; Hitz, Emily; Li, Yiju; Dai, Jiaqi; Xu, Shaomao; Luo, Wei; Wachsman, Eric D; Hu, Liangbing

    2017-01-11

    Solid-state electrolytes are known for nonflammability, dendrite blocking, and stability over large potential windows. Garnet-based solid-state electrolytes have attracted much attention for their high ionic conductivities and stability with lithium metal anodes. However, high-interface resistance with lithium anodes hinders their application to lithium metal batteries. Here, we demonstrate an ultrathin, conformal ZnO surface coating by atomic layer deposition for improved wettability of garnet solid-state electrolytes to molten lithium that significantly decreases the interface resistance to as low as ∼20 Ω·cm(2). The ZnO coating demonstrates a high reactivity with lithium metal, which is systematically characterized. As a proof-of-concept, we successfully infiltrated lithium metal into porous garnet electrolyte, which can potentially serve as a self-supported lithium metal composite anode having both high ionic and electrical conductivity for solid-state lithium metal batteries. The facile surface treatment method offers a simple strategy to solve the interface problem in solid-state lithium metal batteries with garnet solid electrolytes.

  2. High-efficiency dye-sensitized solar cells using ferrocene-based electrolytes and natural photosensitizers

    Science.gov (United States)

    Sönmezoğlu, Savaş; Akyürek, Cafer; Akin, Seçkin

    2012-10-01

    A new and promising dye-sensitized solar cell (DSSC) bilayer design was developed using an Fe2+/Fe3+ (ferrocene) liquid electrolyte and natural dyes extracted from Hypericum perforatum, Rubia tinctorum L. and Reseda luteola. The photovoltaic parameters controlling the device performance were then investigated. A DSSC based on quercetin dye displayed the most efficient solar to electricity conversion efficiency compared with other dyes with a maximum η value of 2.17%. Maximum overall conversion efficiencies under simulated sunlight that was comparable to natural photosynthesis were increased by 15%. The identification of appropriate additives for improving VOC without causing dye degradation may result in further enhancement of cell performance, making the practical application of such systems more suitable for achieving economically viable solar energy devices.

  3. Safe, high-energy supercapacitors based on solvent-free ionic liquid electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Arbizzani, Catia; Biso, Maurizio; Cericola, Dario; Lazzari, Mariachiara; Soavi, Francesca; Mastragostino, Marina [University of Bologna, Dipartimento di Scienza dei Metalli, Elettrochimica e Tecniche Chimiche, via S. Donato 15, 40127 Bologna (Italy)

    2008-12-01

    Safety is the main concern for energy storage-system application in hybrid-electrical vehicles (HEVs) and ionic liquids (ILs) of low vapor pressure and high thermal stability represent a strategy to meet this key requisite. The use of solvent-free ILs in supercapacitors enables the high cell voltages required for increasing supercapacitor energy up to the values for power-assist application in HEVs. In order to exploit the wide electrochemical stability window of ILs, tailored electrode materials and cell configurations have to be used. The performance of asymmetric double-layer carbon supercapacitors (AEDLCs) and carbon/poly(3-methylthiophene) hybrid supercapacitors operating with different pyrrolidinium-based ILs are reported and compared. This study demonstrates that a design-optimized AEDLC operating with safe, solvent-free IL electrolyte meets cycling stability and the energy and power requisites for power-assisted HEVs at the investigated temperatures. (author)

  4. Effects of Silica Nanostructures in Poly(ethylene oxide)-Based Composite Polymer Electrolytes.

    Science.gov (United States)

    Mohanta, Jagdeep; Anwar, Shahid; Si, Satyabrata

    2016-06-01

    The present work describes the synthesis of some poly(ethylene oxide)-based nanocomposite polymer electrolyte films using various silica nanostructures as the inorganic filler by simple solution mixing technique, in which the nature of the silica nanostructures play a vital role in modulating their electrochemical performances at room temperature. The silica nanostructures are prepared by ammonical hydrolysis of tetraethyl orthosilicate following the modified St6ber method. The resulting films are characterized by X-ray diffraction and differential scanning calorimeter to study their crystallinity. Room temperature AC impedance spectroscopy is utilized to determine the Li+ ion conductivity of the resulting films. The observed conductivity values of various NCPE films depend on the nature of silica filling as well as on their surface characteristics and also on the varying PEO-Li+ ratio, which is observed to be in the order of 10(-7)-10(-6) S cm(-1).

  5. Green polymer electrolytes based on chitosan and 1-butyl-3-methylimidazolium acetate

    Science.gov (United States)

    Shamsudin, Intan Juliana; Ahmad, Azizan; Hassan, Nur Hasyareeda

    2014-09-01

    Green polymer electrolytes based on chitosan as the polymer matrix and ionic liquid 1-butyl-3-methylimidazolium acetate [Bmim][OAc] as charge carriers were prepared by solution casting technique. Complexes with various amount of ionic liquid loading were investigated as possible ionic conducting polymers. The ionic conductivity was found to increase with increasing weight percent of ionic liquid. The highest ionic conductivity of the charged chitosan-[Bmim][OAc] was 2.44 × 10-3 S cm-1 at 90 wt.% of [Bmim][OAc] content at ambient temperature. Attenuated Total Reflection Fourier Transform infrared (ATR-FTIR) spectroscopy has proven the interaction between chitosan and [Bmim][OAc]. X-ray Diffraction (XRD) has shown that the amorphosity of the complexes increase as the amount of [Bmim][OAc] increase.

  6. Green polymer electrolytes based on chitosan and 1-butyl-3-methylimidazolium acetate

    Energy Technology Data Exchange (ETDEWEB)

    Shamsudin, Intan Juliana [Chemistry Department, Centre for Defence Foundation Studies, National Defence University of Malaysia, 57000 Kuala Lumpur (Malaysia); Ahmad, Azizan; Hassan, Nur Hasyareeda [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600, Bangi, Selangor Darul Ehsan (Malaysia)

    2014-09-03

    Green polymer electrolytes based on chitosan as the polymer matrix and ionic liquid 1-butyl-3-methylimidazolium acetate [Bmim][OAc] as charge carriers were prepared by solution casting technique. Complexes with various amount of ionic liquid loading were investigated as possible ionic conducting polymers. The ionic conductivity was found to increase with increasing weight percent of ionic liquid. The highest ionic conductivity of the charged chitosan-[Bmim][OAc] was 2.44 × 10{sup −3} S cm{sup −1} at 90 wt.% of [Bmim][OAc] content at ambient temperature. Attenuated Total Reflection Fourier Transform infrared (ATR-FTIR) spectroscopy has proven the interaction between chitosan and [Bmim][OAc]. X-ray Diffraction (XRD) has shown that the amorphosity of the complexes increase as the amount of [Bmim][OAc] increase.

  7. Co-solvents with high coulombic efficiency in propylene carbonate based electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Gao; Zhao, Hui; Park, Sang-Jae

    2017-06-27

    A homologous series of cyclic carbonate or propylene carbonate (PC) analogue solvents with increasing length of linear alkyl substitutes were synthesized and used as co-solvents with PC for graphite based lithium ion half cells. A graphite anode reaches a capacity around 310 mAh/g in PC and its analogue co-solvents with 99.95% Coulombic efficiency. Cyclic carbonate co-solvents with longer alkyl chains are able to prevent exfoliation of graphite when used as co-solvents with PC. The cyclic carbonate co-solvents of PC compete for solvation of Li ion with PC solvent, delaying PC co-intercalation. Reduction products of PC on graphite surfaces via single-electron path form a stable Solid Electrolyte Interphase (SEI), which allows the reversible cycling of graphite.

  8. Highly conductive solid polymer electrolyte membranes based on polyethylene glycol-bis-carbamate dimethacrylate networks

    Science.gov (United States)

    Fu, Guopeng; Dempsey, Janel; Izaki, Kosuke; Adachi, Kaoru; Tsukahara, Yasuhisa; Kyu, Thein

    2017-08-01

    In an effort to fabricate highly conductive, stable solid-state polymer electrolyte membranes (PEM), polyethylene glycol bis-carbamate (PEGBC) was synthesized via condensation reaction between polyethylene glycol diamine and ethylene carbonate. Subsequently, dimethacrylate groups were chemically attached to both ends of PEGBC to afford polyethylene glycol-bis-carbamate dimethacrylate (PEGBCDMA) precursor having crosslinking capability. The melt-mixed ternary mixtures consisting of PEGBCDMA, succinonitrile plasticizer, and lithium trifluorosulphonyl imide salt were completely miscibl