Investigation of holder pressure and size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator.

Science.gov (United States)

Aminzahed, Iman; Mashhadi, Mahmoud Mosavi; Sereshk, Mohammad Reza Vaziri

2017-02-01

Micro forming is a manufacturing process to fabricate micro parts with high quality and a cost effective manner. Deep drawing could be a favorable method for production of complicated parts in macro and micro sizes. In this paper piezoelectric actuator is used as a novel approach in the field of micro manufacturing. Also, in current work, investigations are conducted with four rectangular punches and blanks with various thicknesses. Blank holder pressure effects on thickness distributions, punch force, and springback are studied. According to the results of this work, increasing of blank holder pressure in scaled deep drawing, in contrast to thickness of drawn part, leads to decrease in the punch forces and springback. Furthermore, it is shown that in micro deep drawing, the effects of holder pressure on mentioned parameters can be ignored. Copyright © 2016 Elsevier B.V. All rights reserved.

Engagement of Metal Debris into Gear Mesh

Science.gov (United States)

handschuh, Robert F.; Krantz, Timothy L.

2010-01-01

A series of bench-top experiments was conducted to determine the effects of metallic debris being dragged through meshing gear teeth. A test rig that is typically used to conduct contact fatigue experiments was used for these tests. Several sizes of drill material, shim stock and pieces of gear teeth were introduced and then driven through the meshing region. The level of torque required to drive the "chip" through the gear mesh was measured. From the data gathered, chip size sufficient to jam the mechanism can be determined.

A novel safety device with metal counter meshing gears discriminator directly driven by axial flux permanent magnet micromotors based on MEMS technology

Science.gov (United States)

Zhang, Weiping; Chen, Wenyuan; Zhao, Xiaolin; Li, Shengyong; Jiang, Yong

2005-08-01

In a novel safety device based on MEMS technology for high consequence systems, the discriminator consists of two groups of metal counter meshing gears and two pawl/ratchet wheel mechanisms. Each group of counter meshing gears is onepiece and driven directly by an axial flux permanent magnet micromotor respectively. The energy-coupling element is an optical shutter with two collimators and a coupler wheel. The safety device's probability is less than 1/106. It is fabricated by combination of an LiGA-like process and precision mechanical engineering. The device has simple structure, few dynamic problems, high strength and strong reliability.

Double Helical Gear Performance Results in High Speed Gear Trains

Science.gov (United States)

Handschuh, Robert F.; Ehinger, Ryan; Sinusas, Eric; Kilmain, Charles

2010-01-01

The operation of high speed gearing systems in the transmissions of tiltrotor aircraft has an effect on overall propulsion system efficiency. Recent work has focused on many aspects of high-speed helical gear trains as would be used in tiltrotor aircraft such as operational characteristics, comparison of analytical predictions to experimental data and the affect of superfinishing on transmission performance. Baseline tests of an aerospace quality system have been conducted in the NASA Glenn High-Speed Helical Gear Train Test Facility and have been described in earlier studies. These earlier tests had utilized single helical gears. The results that will be described in this study are those attained using double helical gears. This type of gear mesh can be configured in this facility to either pump the air-oil environment from the center gap between the meshing gears to the outside of tooth ends or in the reverse direction. Tests were conducted with both inward and outward air-oil pumping directions. Results are compared to the earlier baseline results of single helical gears.

Start-up problem with an induction machine and a permanent magnet gear

DEFF Research Database (Denmark)

Frandsen, Tommy; Berg, Nick Ilsø; Holm, Rasmus Koldborg

2014-01-01

This paper presents the preliminary work conducted to design a magnetic gear (MG) integrated with a fan and driven by an grid connected induction machine (IM). A start-up problem with a MG, which occurs due to a high oscillating torque and a high breakdown torque of the IM when starting up directly...

Bevel gear driver and method having torque limit selection

Science.gov (United States)

Cook, Joseph S., Jr.

1994-08-01

This invention comprises a torque drive mechanism utilizing axially translatable, mutually engageable transmission members having mating crown gears, driven and driving members with a three-element drive train being biased together by resilient means or by a fluid actuator system, the apparatus being operable to transmit a precisely controlled degree of torque to a driven member. The apparatus is applicable for use in hand tools and as a replacement for impact torque drivers, torque wrenches, motorized screw drivers, or the like, wherein the applied torque must be precisely controlled or limited. The bevel torque drive includes a drive gear which is axially displaceable and rotatable within cylindrical driver housing, a rotatable intermediate gear, and an output gear. Key rotationally secures displaceable gear with respect to input shaft but permits axial movement therebetween. A thrust bearing is preferably connected to the lower end of shaft for support to reduce play and friction between shaft and a transmission joint disc during rotation of the gear train. Coaxially mounted coiled spring is footed against displaceable gear for biasing the displaceable gear toward and into engagement with the intermediate gear for driving intermediate gear and output gear. Torque control is achieved by the use of straight or spiral beveled gears which are of configurations adapted to withdraw from mutual engagement upon the torque exceeding a predetermined limit. The novel, advantageous features of the invention include the configuration of the mating, crown gear sets and the axially translatable, slidable drive gear. The mechanism is capable of transmitting a high degree of torque within a narrow, compact transmission housing. The compact size and narrow, elongated configuration of the housing is particularly applicable for use in hand tools and in multiple torque driver mechanisms in which it is necessary to drive multiple fasteners which are located in close proximity. Prior

Drawing plan for solid works

International Nuclear Information System (INIS)

Lee, Kuk Hwan; Kim, Hyung Seop; Yu, Dae Won

2004-02-01

This book deals with beginning solid works 2003, setting system option, setting tool group, setting document and storing part template file. It also introduces works of basic solid works modeling such as making of square, circuit, plate washer, square column, block I, block II, link, cover plate, position block and housing. The last part explains drawing of fix block, stopper plate III, bracket, cover, belt pulley, circle plate, square, block, stopper block, angle block, washer, circle block and link.878

ALGORITHM OF WORK OF SYSTEM OF MANAGEMENT BY AUTOMATED GEAR-BOXES CARS

Directory of Open Access Journals (Sweden)

O. Smirnov

2009-01-01

Full Text Available The development of algorithms of management system’s work by the automated gear-boxes vehicles is considered and the results of their practical use on the example of the KamAZ truck are considered.

Drawing a dog: The role of working memory and executive function.

Science.gov (United States)

Panesi, Sabrina; Morra, Sergio

2016-12-01

Previous research suggests that young children draw animals by adapting their scheme for the human figure. This can be considered an early form of drawing flexibility. This study investigated preschoolers' ability to draw a dog that is different from the human figure. The role of working memory capacity and executive function was examined. The participants were 123 children (36-73 months old) who were required to draw both a person and a dog. The dog figure was scored on a list of features that could render it different from the human figure. Regression analyses showed that both working memory capacity and executive function predicted development in the dog drawing; the dog drawing score correlated with working memory capacity and executive function, even partialling out age, motor coordination, and drawing ability (measured with Goodenough's Draw-a-Man test). These results suggest that both working memory capacity and executive function play an important role in the early development of drawing flexibility. The implications regarding executive functions and working memory are also discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

Gear Tooth Root Stresses of a Very Heavily Loaded Gear Pair-Case Study: Orbiter Body Flap Actuator Pinion and Ring Gear

Science.gov (United States)

Krantz, Timothy L.; Handschuh, Robert F.

2015-01-01

The space shuttle orbiter's body flap actuator gearing was assessed as a case study of the stresses for very heavily loaded external-internal gear pairs (meshing pinion and ring gear). For many applications, using the high point of single tooth contact (HPSTC) to locate the position of the tooth force is adequate for assessing the maximum tooth root stress condition. But for aerospace gearing such an approach may be inadequate for assessing the stress condition while also simultaneously minimizing mass. In this work specialized contact analyses and finite element methods were used to study gear tooth stresses of body flap actuator gears. The analytical solutions considered the elastic deformations as an inherent part of the solutions. The ratio for the maximum tooth stresses using the HPSTC approach solutions relative to the contact analysis and finite element solutions were 1.40 for the ring gear and 1.28 for the pinion gear.

Engagement of Metal Debris into a Gear Mesh

Science.gov (United States)

Handschuh, Robert F.; Krantz, Timothy L.

2010-01-01

A series of bench top experiments was conducted to determine the effects of metallic debris being dragged through meshing gear teeth. A test rig that is typically used to conduct contact fatigue experiments was used for these tests. Several sizes of drill material, shim stock, and pieces of gear teeth were introduced and then driven through the meshing region. The level of torque required to drive the "chip" through the gear mesh was measured. From the data gathered, chip size sufficient to jam the mechanism can be determined.

SimSketch & GearSketch: Sketch-based modelling for early science education

NARCIS (Netherlands)

van Joolingen, Wouter; Bollen, Lars; Leenaars, Frank

2012-01-01

In this interactive demo, we will present two modelling and drawing applications - SimSketch & GearSketch, which exemplarily demonstrate our approaches to sketch-based learning and modelling in early (science) education. Since drawings and sketches denote are very basic and fundamental way of

46 CFR 28.885 - Cargo gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Cargo gear. 28.885 Section 28.885 Shipping COAST GUARD... Aleutian Trade Act Vessels § 28.885 Cargo gear. (a) The safe working load (SWL) for the assembled gear... the load the gear is approved to lift, excluding the weight of the gear itself. (b) All wire rope...

Materials and lubrication for gear and bearing surfaces in uhv

International Nuclear Information System (INIS)

Kirby, R.E.; Collet, G.J.; Garwin, E.L.

1980-06-01

During design and construction of the SLAC polarized LEED (PLEED) system, a search was made for a dependable gear, bearing, and lubrication system for the computer-controlled Faraday cup used to measure diffracted beams. Components must be nonmagnetic, bakeable to 250 0 C, and at room temperature must operate at pressures in the 10 -9 to 10 -10 Pa range. A test system was constructed which incorporated a meshed pair of dissimilar pitch diameter spur gears, one of which was confined to (by bushings) and rotated on a fixed shaft, while the other gear was driven by a commercial rotary motion feedthrough which was rotated by a servo motor driven in sine fashion with a direction reversal every six turns and peak speeds of 50 rpm. The criterion for a successful pair was approx. 10 5 turns, the life rating for the feedthrough. Pairs had actual turn counts from less than 1 to 91,000. Materials for gears included stainless steel, beryllium copper, and aluminum alloys. Lubricants used singly and in concert were MoS 2 , WS 2 , Ag, hard chrome, and a MoS 2 -graphite-sodium silicate mixture. The successful gear pair was Ag-plated Al alloy and MoS 2 -graphite-sodium silicate-coated Be-Cu. Subsequent performance in the PLEED system after repeated bakeouts will also be discussed

A method for gear fatigue life prediction considering the internal flow field of the gear pump

Science.gov (United States)

Shen, Haidong; Li, Zhiqiang; Qi, Lele; Qiao, Liang

2018-01-01

Gear pump is the most widely used volume type hydraulic pump, and it is the main power source of the hydraulic system. Its performance is influenced by many factors, such as working environment, maintenance, fluid pressure and so on. It is different from the gear transmission system, the internal flow field of gear pump has a greater impact on the gear life, therefore it needs to consider the internal hydraulic system when predicting the gear fatigue life. In this paper, a certain aircraft gear pump as the research object, aim at the typical failure forms, gear contact fatigue, of gear pump, proposing the prediction method based on the virtual simulation. The method use CFD (Computational fluid dynamics) software to analyze pressure distribution of internal flow field of the gear pump, and constructed the unidirectional flow-solid coupling model of gear to acquire the contact stress of tooth surface on Ansys workbench software. Finally, employing nominal stress method and Miner cumulative damage theory to calculated the gear contact fatigue life based on modified material P-S-N curve. Engineering practice show that the method is feasible and efficient.

Improving bending stress in spur gears using asymmetric gears and shape optimization

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2010-01-01

Bending stress plays a significant role in gear design wherein its magnitude is controlled by the nominal bending stress and the stress concentration due to the geometrical shape. The bending stress is indirectly related to shape changes made to the cutting tool. This work shows that the bending...... stress can be reduced significantly by using asymmetric gear teeth and by shape optimizing the gear through changes made to the tool geometry. However, to obtain the largest possible stress reduction a custom tool must be designed depending on the number of teeth, but the stress reductions found...

Boundary Drawing in Clinical Work

DEFF Research Database (Denmark)

Meier, Ninna

The aim of this paper is to show how health care professionals temporarily dissolve and redraw boundaries in their everyday work, in order to coordinate clinical work and facilitate collaboration in patient pathways. Boundaries are social constructions that help us make sense of our complex, social...... world. In health care, formal boundaries are important distinctions that separate health care practitioners into medical specialties, professions and organizational departments. But clinical work also relies on the ability of health care practitioners to collaborate around patients in formal...... arrangements or emergent, temporary teams. Focusing on the cognitive and social boundaries we draw to establish identity and connection (to a profession, team or person) the paper shows how health care professionals can use inter-personal relationships to temporarily dismiss formal boundaries. By redrawing...

Materials and lubrication for gear and bearing surfaces in UHV

International Nuclear Information System (INIS)

Kirby, R.E.; Collet, G.J.; Garwin, E.L.

1981-01-01

During design and construction of the SLAC polarized LEED (PLEED) system, a search was made for a dependable gear, bearing and lubrication system for the computer-controlled Faraday cup used to measure diffracted beams. Components must be nonmagnetic, bakeable to 250 0 C, and at room temperature must operate at pressures in the 10 -9 to 10 -10 Pa range. A test system was constructed which incorporated a meshed pair of dissimilar pitch diameter spur gears, one of which was confined by bushings to a fixed shaft on which it rotated, while the other gear was driven through a commercial rotary motion feedthrough rotated by a servo motor driven in sine fashion with a direction reversal every six turns and peak speeds of 50 rpm. The criterion for a successful pair was approx. equal to 10 5 turns, the life rating for the feedthrough. Pairs had actual turn counts from less than 1 to 91 000. Materials for gears included stainless steel, beryllium copper and aluminium alloys. Lubricants used singly and in concert were MoS 2 , WS 2 , Ag, hard chrome and a MoS 2 -graphite-sodium silicate-coated Be-Cu. Subsequent performance in the PLEED system after repeated bakeouts will also be discussed. (orig.)

Principal Components of Superhigh-Dimensional Statistical Features and Support Vector Machine for Improving Identification Accuracies of Different Gear Crack Levels under Different Working Conditions

Directory of Open Access Journals (Sweden)

Dong Wang

2015-01-01

Full Text Available Gears are widely used in gearbox to transmit power from one shaft to another. Gear crack is one of the most frequent gear fault modes found in industry. Identification of different gear crack levels is beneficial in preventing any unexpected machine breakdown and reducing economic loss because gear crack leads to gear tooth breakage. In this paper, an intelligent fault diagnosis method for identification of different gear crack levels under different working conditions is proposed. First, superhigh-dimensional statistical features are extracted from continuous wavelet transform at different scales. The number of the statistical features extracted by using the proposed method is 920 so that the extracted statistical features are superhigh dimensional. To reduce the dimensionality of the extracted statistical features and generate new significant low-dimensional statistical features, a simple and effective method called principal component analysis is used. To further improve identification accuracies of different gear crack levels under different working conditions, support vector machine is employed. Three experiments are investigated to show the superiority of the proposed method. Comparisons with other existing gear crack level identification methods are conducted. The results show that the proposed method has the highest identification accuracies among all existing methods.

50 CFR 665.227 - Allowable gear and gear restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Fisheries § 665.227 Allowable gear and gear restrictions. (a) Hawaii coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp gun; (4...

50 CFR 665.427 - Allowable gear and gear restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Archipelago Fisheries § 665.427 Allowable gear and gear restrictions. (a) Mariana coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp...

Intelligent Test Mechanism Design of Worn Big Gear

Directory of Open Access Journals (Sweden)

Hong-Yu LIU

2014-10-01

Full Text Available With the continuous development of national economy, big gear was widely applied in metallurgy and mine domains. So, big gear plays an important role in above domains. In practical production, big gear abrasion and breach take place often. It affects normal production and causes unnecessary economic loss. A kind of intelligent test method was put forward on worn big gear mainly aimed at the big gear restriction conditions of high production cost, long production cycle and high- intensity artificial repair welding work. The measure equations transformations were made on involute straight gear. Original polar coordinate equations were transformed into rectangular coordinate equations. Big gear abrasion measure principle was introduced. Detection principle diagram was given. Detection route realization method was introduced. OADM12 laser sensor was selected. Detection on big gear abrasion area was realized by detection mechanism. Tested data of unworn gear and worn gear were led in designed calculation program written by Visual Basic language. Big gear abrasion quantity can be obtained. It provides a feasible method for intelligent test and intelligent repair welding on worn big gear.

50 CFR 665.127 - Allowable gear and gear restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Fisheries § 665.127 Allowable gear and gear restrictions. (a) American Samoa coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp gun; (4...

50 CFR 665.627 - Allowable gear and gear restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Allowable gear and gear restrictions. 665... Island Area Fisheries § 665.627 Allowable gear and gear restrictions. (a) Coral reef ecosystem MUS may be taken only with the following allowable gear and methods: (1) Hand harvest; (2) Spear; (3) Slurp gun; (4...

Performance-based gear metrology kinematic, transmission, error computation and diagnosis

CERN Document Server

Mark, William D

2012-01-01

A mathematically rigorous explanation of how manufacturing deviations and damage on the working surfaces of gear teeth cause transmission-error contributions to vibration excitations Some gear-tooth working-surface manufacturing deviations of significant amplitude cause negligible vibration excitation and noise, yet others of minuscule amplitude are a source of significant vibration excitation and noise.   Presently available computer-numerically-controlled dedicated gear metrology equipment can measure such error patterns on a gear in a few hours in sufficient detail to enable

Reduction of belt CVT gear noise by gear train modification. Optimize vibration characteristics of gear train; Belt CVT no gear noise teigen gijutsu. Gear train shindo tokusei no saitekika

Energy Technology Data Exchange (ETDEWEB)

Arimatsu, M; Kawakami, T [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

With the reduction of vehicle noise, the requirements for an efficient method to reduce transmission gear noise have become stronger yearly. So far efforts to reduce gear noise have generally focused on ways of improving the gears themselves. In addition to these traditional methods, it proved very beneficial to us to optimize the gear train structure. Nissan has just released the new Belt CVT for 2.0L Front wheel drive vehicles. We have been analyzing vibration of the gear train by using a finite element model since the early development stage, and we could achieve the quiet gears effectively. 2 refs., 9 figs.

50 CFR 648.84 - Gear-marking requirements and gear restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Gear-marking requirements and gear... Management Measures for the NE Multispecies and Monkfish Fisheries § 648.84 Gear-marking requirements and gear restrictions. (a) Bottom-tending fixed gear, including, but not limited to, gillnets and longlines...

High Pressure Angle Gears: Comparison to Typical Gear Designs

Science.gov (United States)

Handschuh, Robert F.; Zabrajsek, Andrew J.

2010-01-01

A preliminary study has been completed to determine the feasibility of using high-pressure angle gears in aeronautic and space applications. Tests were conducted in the NASA Glenn Research Center (GRC) Spur Gear Test Facility at speeds up to 10,000 rpm and 73 N*m (648 in.*lb) for 3.18, 2.12, and 1.59 module gears (8, 12, and 16 diametral pitch gears), all designed to operate in the same test facility. The 3.18 module (8-diametral pitch), 28 tooth, 20deg pressure angle gears are the GRC baseline test specimen. Also, 2.12 module (12-diametral pitch), 42 tooth, 25deg pressure angle gears were tested. Finally 1.59 module (16-diametral pitch), 56 tooth, 35deg pressure angle gears were tested. The high-pressure angle gears were the most efficient when operated in the high-speed aerospace mode (10,000 rpm, lubricated with a synthetic turbine engine oil), and produced the lowest wear rates when tested with a perfluoroether-based grease. The grease tests were conducted at 150 rpm and 71 N*m (630 in.*lb).

Modern gear production

CERN Document Server

Watson, H J

1970-01-01

Modern Gear Production focuses on the processes and methods in gear making. The book first gives information on the history of gear making and types of gears. Topics such as the classification of gears based on the disposition of their shafts; shafts lying in the same plane with axes intersecting; and shafts lying in parallel planes but with axes inclined to one another are then discussed. The text describes gear groups, tooth forms, and gear materials. Heat treatment of steels, casehardening, nitriding, induction hardening, sulfinuzing, and flame hardening are explained. The book takes a look

Feynman diagram drawing made easy

International Nuclear Information System (INIS)

Baillargeon, M.

1997-01-01

We present a drawing package optimised for Feynman diagrams. These can be constructed interactively with a mouse-driven graphical interface or from a script file, more suitable to work with a diagram generator. It provides most features encountered in Feynman diagrams and allows to modify every part of a diagram after its creation. Special attention has been paid to obtain a high quality printout as easily as possible. This package is written in Tcl/Tk and in C. (orig.)

Vibration Based Sun Gear Damage Detection

Science.gov (United States)

Hood, Adrian; LaBerge, Kelsen; Lewicki, David; Pines, Darryll

2013-01-01

Seeded fault experiments were conducted on the planetary stage of an OH-58C helicopter transmission. Two vibration based methods are discussed that isolate the dynamics of the sun gear from that of the planet gears, bearings, input spiral bevel stage, and other components in and around the gearbox. Three damaged sun gears: two spalled and one cracked, serve as the focus of this current work. A non-sequential vibration separation algorithm was developed and the resulting signals analyzed. The second method uses only the time synchronously averaged data but takes advantage of the signal/source mapping required for vibration separation. Both algorithms were successful in identifying the spall damage. Sun gear damage was confirmed by the presence of sun mesh groups. The sun tooth crack condition was inconclusive.

Load Sharing Behavior of Star Gearing Reducer for Geared Turbofan Engine

Science.gov (United States)

Mo, Shuai; Zhang, Yidu; Wu, Qiong; Wang, Feiming; Matsumura, Shigeki; Houjoh, Haruo

2017-07-01

Load sharing behavior is very important for power-split gearing system, star gearing reducer as a new type and special transmission system can be used in many industry fields. However, there is few literature regarding the key multiple-split load sharing issue in main gearbox used in new type geared turbofan engine. Further mechanism analysis are made on load sharing behavior among star gears of star gearing reducer for geared turbofan engine. Comprehensive meshing error analysis are conducted on eccentricity error, gear thickness error, base pitch error, assembly error, and bearing error of star gearing reducer respectively. Floating meshing error resulting from meshing clearance variation caused by the simultaneous floating of sun gear and annular gear are taken into account. A refined mathematical model for load sharing coefficient calculation is established in consideration of different meshing stiffness and supporting stiffness for components. The regular curves of load sharing coefficient under the influence of interactions, single action and single variation of various component errors are obtained. The accurate sensitivity of load sharing coefficient toward different errors is mastered. The load sharing coefficient of star gearing reducer is 1.033 and the maximum meshing force in gear tooth is about 3010 N. This paper provides scientific theory evidences for optimal parameter design and proper tolerance distribution in advanced development and manufacturing process, so as to achieve optimal effects in economy and technology.

Recent Advances in the Analysis of Spiral Bevel Gears

Science.gov (United States)

Handschuh, Robert F.

1997-01-01

A review of recent progress for the analysis of spiral bevel gears will be described. The foundation of this work relies on the description of the gear geometry of face-milled spiral bevel gears via the approach developed by Litvin. This methodology was extended by combining the basic gear design data with the manufactured surfaces using a differential geometry approach, and provides the data necessary for assembling three-dimensional finite element models. The finite element models have been utilized to conduct thermal and structural analysis of the gear system. Examples of the methods developed for thermal and structural/contact analysis are presented.

A cycloidal wobble motor driven by shape memory alloy wires

International Nuclear Information System (INIS)

Hwang, Donghyun; Higuchi, Toshiro

2014-01-01

A cycloidal wobble motor driven by shape memory alloy (SMA) wires is proposed. In realizing a motor driving mechanism well known as a type of reduction system, a cycloidal gear mechanism is utilized. It facilitates the achievement of bidirectional continuous rotation with high-torque capability, based on its high efficiency and high reduction ratio. The applied driving mechanism consists of a pin/roller based annular gear as a wobbler, a cycloidal disc as a rotor, and crankshafts to guide the eccentric wobbling motion. The wobbling motion of the annular gear is generated by sequential activation of radially phase-symmetrically placed SMA wires. Consequently the cycloidal disc is rotated by rolling contact based cycloidal gearing between the wobbler and the rotor. In designing the proposed motor, thermomechanical characterization of an SMA wire biased by extension springs is experimentally performed. Then, a simplified geometric model for the motor is devised to conduct theoretical assessment of design parametric effects on structural features and working performance. With consideration of the results from parametric analysis, a functional prototype three-phase motor is fabricated to carry out experimental verification of working performance. The observed experimental results including output torque, rotational speed, bidirectional positioning characteristic, etc obviously demonstrate the practical applicability and potentiality of the wobble motor. (paper)

analysis of gear milling at vari gear milling at various gear milling

African Journals Online (AJOL)

eobe

2 DEPARTMENT OF INDUSTRIAL AND ... conventional machine tools, cutter tool wear, .... speed, and tool wear on case-hardened gear is also .... study. The gear cutter is mounted on the spindle. Spindle speeds and feed rates are essential ...

On the automatic generation of FEM models for complex gears - A work-in-progress report

Science.gov (United States)

Drago, R. J.

1982-01-01

A description is presented of the development and use of a preprocessor to create a NASTRAN finite element model of a complex spur, helical, or spiral bevel gear quickly, inexpensively, and accurately. The preprocessor creates a ready to run NASTRAN input deck including the executive, case control, and bulk data sections. It generates nodes and solid elements to model spur, helical, or spiral bevel gear teeth with integral shafting. Either a complete gear shafting model or a symmetric model is created. The fundamental building block of the gear model is the base layer. The base layer is the mesh configuration of one layer of one tooth segment which is in turn duplicated, translated, and rotated to create the completed model of the gear. Once the base layer is created, the construction of the finite element model is straightforward.

Gear ratting noise reduction of diesel engine; Diesel engine no gear hauchi soon teigen

Energy Technology Data Exchange (ETDEWEB)

Nakamura, S; Miura, Y [Hino Motors, Ltd., Tokyo (Japan)

1997-10-01

Gear raffling noise of diesel engine at idling condition is required to reduce for keeping quiet environment and comfort of driver and passengers on track and bus. Decrease of gear backlash is generally adopted for reducing gear rattling noise. On the other hand, it has been found that newly devised measurement of gear teeth speed and gear meshing error has clarified phenomena of gear rattling between the crankshaft gear and the camshaft gear of the diesel engine. And it has been also found that gear ratting noise is reduced by changing meshing between the crankshaft gear and the camshaft gear. 2 refs., 10 figs.

Analysis of justification for applying two gear sets within the universal gear reducers

OpenAIRE

Rackov Milan; Kuzmanović Siniša; Knežević Ivan; Čavić Maja; Penčić Marko

2017-01-01

In the area of universal gear reducers, standard does not prescribe relations between load capacity, gear ratios and axis heights. Therefore, larger load capacity of some gear reducers manufacturers has advantage for lower gear ratio and, vice versa, smaller load capacity of the gearbox achieves higher values of gear ratio. However, there are some manufacturers who produce gear reducers with smaller or larger load capacity for higher or lower gear ratio, within the same axis height. This pape...

A superconducting magnetic gear

International Nuclear Information System (INIS)

Campbell, A M

2016-01-01

A comparison is made between a magnetic gear using permanent magnets and superconductors. The objective is to see if there are any fundamental reasons why superconducting magnets should not provide higher power densities than permanent magnets. The gear is based on the variable permeability design of Attilah and Howe (2001 IEEE Trans. Magn. 37 2844–46) in which a ring of permanent magnets surrounding a ring of permeable pole pieces with a different spacing gives an internal field component at the beat frequency. Superconductors can provide much larger fields and forces but will saturate the pole pieces. However the gear mechanism still operates, but in a different way. The magnetisation of the pole pieces is now constant but rotates with angle at the beat frequency. The result is a cylindrical Halbach array which produces an internal field with the same symmetry as in the linear regime, but has an analytic solution. In this paper a typical gear system is analysed with finite elements using FlexPDE. It is shown that the gear can work well into the saturation regime and that the Halbach array gives a good approximation to the results. Replacing the permanent magnets with superconducting tapes can give large increases in torque density, and for something like a wind turbine a combined gear and generator is possible. However there are major practical problems. Perhaps the most fundamental is the large high frequency field which is inevitably present and which will cause AC losses. Also large magnetic fields are required, with all the practical problems of high field superconducting magnets in rotating machines. Nevertheless there are ways of mitigating these difficulties and it seems worthwhile to explore the possibilities of this technology further. (paper)

Offset Compound Gear Drive

Science.gov (United States)

Stevens, Mark A.; Handschuh, Robert F.; Lewicki, David G.

2010-01-01

The Offset Compound Gear Drive is an in-line, discrete, two-speed device utilizing a special offset compound gear that has both an internal tooth configuration on the input end and external tooth configuration on the output end, thus allowing it to mesh in series, simultaneously, with both a smaller external tooth input gear and a larger internal tooth output gear. This unique geometry and offset axis permits the compound gear to mesh with the smaller diameter input gear and the larger diameter output gear, both of which are on the same central, or primary, centerline. This configuration results in a compact in-line reduction gear set consisting of fewer gears and bearings than a conventional planetary gear train. Switching between the two output ratios is accomplished through a main control clutch and sprag. Power flow to the above is transmitted through concentric power paths. Low-speed operation is accomplished in two meshes. For the purpose of illustrating the low-speed output operation, the following example pitch diameters are given. A 5.0 pitch diameter (PD) input gear to 7.50 PD (internal tooth) intermediate gear (0.667 reduction mesh), and a 7.50 PD (external tooth) intermediate gear to a 10.00 PD output gear (0.750 reduction mesh). Note that it is not required that the intermediate gears on the offset axis be of the same diameter. For this example, the resultant low-speed ratio is 2:1 (output speed = 0.500; product of stage one 0.667 reduction and stage two 0.750 stage reduction). The design is not restricted to the example pitch diameters, or output ratio. From the output gear, power is transmitted through a hollow drive shaft, which, in turn, drives a sprag during which time the main clutch is disengaged.

Energy efficiency improvement by gear shifting optimization

Directory of Open Access Journals (Sweden)

Blagojevic Ivan A.

2013-01-01

Full Text Available Many studies have proved that elements of driver’s behavior related to gear selection have considerable influence on the fuel consumption. Optimal gear shifting is a complex task, especially for inexperienced drivers. This paper presents an implemented idea for gear shifting optimization with the aim of fuel consumption minimization with more efficient engine working regimes. Optimized gear shifting enables the best possible relation between vehicle motion regimes and engine working regimes. New theoretical-experimental approach has been developed using On-Board Diagnostic technology which so far has not been used for this purpose. The matrix of driving modes according to which tests were performed is obtained and special data acquisition system and analysis process have been developed. Functional relations between experimental test modes and adequate engine working parameters have been obtained and all necessary operations have been conducted to enable their use as inputs for the designed algorithm. The created Model has been tested in real exploitation conditions on passenger car with Otto fuel injection engine and On-Board Diagnostic connection without any changes on it. The conducted tests have shown that the presented Model has significantly positive effects on fuel consumption which is an important ecological aspect. Further development and testing of the Model allows implementation in wide range of motor vehicles with various types of internal combustion engines.

Effect of tooth profile modification on wear in internal gears

Science.gov (United States)

Tunalioglu, M. S.; Tuc, B.

2018-05-01

Internal gears are often used in the automotive industry when two gears are required to rotate in the same direction. Tooth shapes, slippage speeds at the beginning and end of meshing are different according to the external gears. Manufacturing of internal gears is more difficult than external gears. Thus, it is necessary to determine the working conditions and wear behavior of internal gears carefully. The profile modification method in terms of strength and surface tension of the gear mechanism are performed in order to increase the load-carrying capability. In this study, profile modification method was performed in the internal gears to reduce the wear on the teeth. For this purpose, the wear of the internal gears was theoretically investigated by adapting the Archard wear equation to the internal gears. Closed circuit power circulation system was designed and manufactured to experimentally investigate the wear in internal gears. With this system, wear tests of gears made of St 50 material without profile modification and different profile modifications were made and the results were compared. Experimental study was performed in the same loading and cycle time conditions to validate the theoretical results and it was seen that the results are compatible. According to the experimental results, it is seen that in the internal gears, when profile modification done the wear is decreased in the teeth tip region.

Design of control system for optical fiber drawing machine driven by double motor

Science.gov (United States)

Yu, Yue Chen; Bo, Yu Ming; Wang, Jun

2018-01-01

Micro channel Plate (MCP) is a kind of large-area array electron multiplier with high two-dimensional spatial resolution, used as high-performance night vision intensifier. The high precision control of the fiber is the key technology of the micro channel plate manufacturing process, and it was achieved by the control of optical fiber drawing machine driven by dual-motor in this paper. First of all, utilizing STM32 chip, the servo motor drive and control circuit was designed to realize the dual motor synchronization. Secondly, neural network PID control algorithm was designed for controlling the fiber diameter fabricated in high precision; Finally, the hexagonal fiber was manufactured by this system and it shows that multifilament diameter accuracy of the fiber is +/- 1.5μm.

Gear bearing drive

Science.gov (United States)

Mavroidis, Constantinos (Inventor); Vranish, John M. (Inventor); Weinberg, Brian (Inventor)

2011-01-01

A gear bearing drive provides a compact mechanism that operates as an actuator providing torque and as a joint providing support. The drive includes a gear arrangement integrating an external rotor DC motor within a sun gear. Locking surfaces maintain the components of the drive in alignment and provide support for axial loads and moments. The gear bearing drive has a variety of applications, including as a joint in robotic arms and prosthetic limbs.

Elasto-dynamic analysis of a gear pump-Part III: Experimental validation procedure and model extension to helical gears

Science.gov (United States)

Mucchi, E.; Dalpiaz, G.

2015-01-01

This work concerns external gear pumps for automotive applications, which operate at high speed and low pressure. In previous works of the authors (Part I and II, [1,2]), a non-linear lumped-parameter kineto-elastodynamic model for the prediction of the dynamic behaviour of external gear pumps was presented. It takes into account the most important phenomena involved in the operation of this kind of machine. The two main sources of noise and vibration are considered: pressure pulsation and gear meshing. The model has been used in order to foresee the influence of working conditions and design modifications on vibration generation. The model's experimental validation is a difficult task. Thus, Part III proposes a novel methodology for the validation carried out by the comparison of simulations and experimental results concerning forces and moments: it deals with the external and inertial components acting on the gears, estimated by the model, and the reactions and inertial components on the pump casing and the test plate, obtained by measurements. The validation is carried out comparing the level of the time synchronous average in the time domain and the waterfall maps in the frequency domain, with particular attention to identify system resonances. The validation results are satisfactory globally, but discrepancies are still present. Moreover, the assessed model has been properly modified for the application to a new virtual pump prototype with helical gears in order to foresee gear accelerations and dynamic forces. Part IV is focused on improvements in the modelling and analysis of the phenomena bound to the pressure evolution around the gears in order to achieve results closer to the measured values. As a matter of fact, the simulation results have shown that a variable meshing stiffness has a notable contribution on the dynamic behaviour of the pump but this is not as important as the pressure phenomena. As a consequence, the original model was modified with the

Kinematic geometry of gearing

CERN Document Server

Dooner, David B

2012-01-01

Building on the first edition published in 1995 this new edition of Kinematic Geometry of Gearing has been extensively revised and updated with new and original material. This includes the methodology for general tooth forms, radius of torsure', cylinder of osculation, and cylindroid of torsure; the author has also completely reworked the '3 laws of gearing', the first law re-written to better parallel the existing 'Law of Gearing" as pioneered by Leonard Euler, expanded from Euler's original law to encompass non-circular gears and hypoid gears, the 2nd law of gearing describing a unique relat

Advanced theories of hypoid gears

CERN Document Server

Wang, Xudong

2013-01-01

In order to develop more efficient types of gears, further investigation into the theories of engagement is necessary. Up until now most of the research work on the theories of engagement has been carried out separately on different groups, and based on individual types of profiles. This book aims at developing some universal theories, which can not only be used for all types of gears, but can also be utilized in other fields such as sculptured surfaces. The book has four characteristics: the investigations are concentrated on mismatched tooth surfaces; all the problems are dealt with from a

Conductive ink print on PA66 gear for manufacturing condition monitoring sensors

Science.gov (United States)

Futagawa, Shintaro; Iba, Daisuke; Kamimoto, Takahiro; Nakamura, Morimasa; Miura, Nanako; Iizuka, Takashi; Masuda, Arata; Sone, Akira; Moriwaki, Ichiro

2018-03-01

Failures detection of rotating machine elements, such as gears, is an important issue. The purpose of this study was to try to solve this issue by printing conductive ink on gears to manufacture condition-monitoring sensors. In this work, three types of crack detection sensor were designed and the sprayed conductive ink was directly sintered on polyimide (PI) - coated polyamide (PA) 66 gears by laser. The result showed that it was possible to produce narrow circuit lines of the conductive ink including Ag by laser sintering technique and the complex shape sensors on the lateral side of the PA66 gears, module 1.0 mm and tooth number 48. A preliminary operation test was carried out for investigation of the function of the sensors. As a result of the test, the sensors printed in this work should be effective for detecting cracks at tooth root of the gears and will allow for the development of better equipment and detection techniques for health monitoring of gears.

Performance Investigation of a Full-Scale Hybrid Composite Bull Gear

Science.gov (United States)

LaBerge, Kelsen; Handschuh, Robert; Roberts, Gary; Thorp, Scott

2016-01-01

Hybrid composite gears have been investigated as a weight saving technology for rotorcraft transmissions. These gears differ from conventional steel gears in that the structural material between the shaft interface and the gear rim is replaced with a lightweight carbon fiber composite. The work discussed here is an extension of previous coupon level hybrid gear tests to a full-scale bull gear. The NASA Glenn Research Center High-Speed Helical Gear Rig was modified for this program allowing several hybrid gear web configurations to be tested while utilizing the same gear rim. Testing was performed on both a baseline (steel) web configuration and a hybrid (steel-composite)configuration. Vibration, orbit and temperature data were recorded and compared between configurations. Vibration levels did not differ greatly between the hybrid and steel configurations, nor did temperature differential between inlet and outlet. While orbit shape displayed differences between the hybrid and baseline configurations, the general overall amplitude was comparable. The hybrid configuration discussed here successfully ran at 3300 hp(2,460 kW), however, progressive growth of the orbit while running at this test condition discontinued the test. Researchers continue to search for the cause of this orbit shift.

The Design of Intelligent Repair Welding Mechanism and Relative Control System of Big Gear

Directory of Open Access Journals (Sweden)

Hong-Yu LIU

2014-10-01

Full Text Available Effective repair of worn big gear has large influence on ensuring safety production and enhancing economic benefits. A kind of intelligent repair welding method was put forward mainly aimed at the big gear restriction conditions of high production cost, long production cycle and high- intensity artificial repair welding work. Big gear repair welding mechanism was designed in this paper. The work principle and part selection of big gear repair welding mechanism was introduced. The three dimensional mode of big gear repair welding mechanism was constructed by Pro/E three dimensional design software. Three dimensional motions can be realized by motor controlling ball screw. According to involute gear feature, the complicated curve motion on curved gear surface can be transformed to linear motion by orientation. By this way, the repair welding on worn gear area can be realized. In the design of big gear repair welding mechanism control system, Siemens S7-200 series hardware was chosen. Siemens STEP7 programming software was chosen as system design tool. The entire repair welding process was simulated by experiment simulation. It provides a kind of practical and feasible method for the intelligent repair welding of big worn gear.

Nonlinear Vibroimpact Characteristics of a Planetary Gear Transmission System

Directory of Open Access Journals (Sweden)

Jianxing Zhou

2016-01-01

Full Text Available In order to research the vibroimpact characteristics of a planetary gear transmission system under high speed and lightly loaded conditions, a new modeling method is proposed. In the modeling process, linear spring was used to simulate gear mesh elasticity under heavy load cases, and Hertz contact theory was used to calculate the contact force of gear pair under light load cases. Then, effects of the working conditions on the system vibroimpact characteristics are analyzed. The results show that, with input speed growing, the mesh force produced obvious fluctuations on the resonance frequencies of the sun gear and carrier torsion vibration, ring gear’s transverse vibration under the heavy load. Under light load condition, the collision vibration occurs in the gear pair; the changing trend of the contact force shows strongly nonlinear characteristics. The time of mesh-apart in gears pair decreases gradually as the load is increased; until it reaches collision vibration threshold value, the gear pair is no longer mesh-apart. With increasing of the input speed, the time of mesh-apart is decreased gradually; the fluctuation amplitude of contact force shows a linearly increasing trend. The study provides useful theoretical guideline for planetary gear transmission low-noise design.

George Wallis (1811-1891) and Ernest Beinfeld Havell (1861-1934): Juxtaposing Historical Perspectives on Nineteenth-Century Drawing Books in England and India

Science.gov (United States)

Kantawala, Ami; Daichendt, G. James

2017-01-01

Drawing books can be seen as a vital component to teaching and learning art. They serve as an excellent resource for understanding the historical context of teaching drawing. As the industrial revolution geared forward in the nineteenth century, drawing books became a crucial source for sharing and disseminating educational philosophies for the…

Landing gear noise attenuation

Science.gov (United States)

Moe, Jeffrey W. (Inventor); Whitmire, Julia (Inventor); Kwan, Hwa-Wan (Inventor); Abeysinghe, Amal (Inventor)

2011-01-01

A landing gear noise attenuator mitigates noise generated by airframe deployable landing gear. The noise attenuator can have a first position when the landing gear is in its deployed or down position, and a second position when the landing gear is in its up or stowed position. The noise attenuator may be an inflatable fairing that does not compromise limited space constraints associated with landing gear retraction and stowage. A truck fairing mounted under a truck beam can have a compliant edge to allow for non-destructive impingement of a deflected fire during certain conditions.

Gearing Up for Mountain Biking.

Science.gov (United States)

Jahnke, Thomas; Hamson, Mike

1999-01-01

Examines the gear system of a mountain bike to discover any redundancy in the many gear settings available to the cyclist. Suggests a best strategy for changing up through the gears on a typical 21-gear system and an adjustment to the available gears that would result in a smoother change. (Author/ASK)

Near-net shape manufacturing of miniature spur gears by wire spark erosion machining

CERN Document Server

Gupta, Kapil

2016-01-01

This work describes an experimental investigation with the aim to evaluate and establish wire spark erosion machining (WSEM) as a viable alternative for high quality miniature gear manufacturing. External spur type miniature brass (ASTM 858) gears with 12 teeth, 9.8 mm outside diameter and 5 mm face width were manufactured by WSEM. The research work was accomplished in four distinct experimental stages viz., preliminary, pilot, main and confirmation. The aim, scope and findings of each stage are progressively presented and discussed. In essence, the investigation found that it was possible to manufacture miniature gears to high quality by using WSEM. Gears up to DIN 5 quality with a good surface finish (1.2 µm average roughness) and satisfactory surface integrity were achieved. The results suggest that WSEM should be considered a viable alternative to conventional miniature gear manufacturing techniques and that in some instances it may even be superior. This work will prove useful to researchers and profess...

Process and device for producing a timber gear case for tunnels and mines

Energy Technology Data Exchange (ETDEWEB)

Foik, A

1977-09-08

A device is described for producing a timber gear case for tunnels and mines. Plank shaped pillars, partly overlapping one another are driven in parallel planes at an angle to the tunnel axis, close together and advancing relative to the face. The pillars are taken through supports erected one after the other in the longitudinal direction of the tunnel, and are supported. The process can be extended by producing a timber gear case to secure any type of underground space. The process produces further mechanisation of tunnelling and mining and also ensures greater safety for the miners.

Estimating Gear Teeth Stiffness

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2013-01-01

The estimation of gear stiffness is important for determining the load distribution between the gear teeth when two sets of teeth are in contact. Two factors have a major influence on the stiffness; firstly the boundary condition through the gear rim size included in the stiffness calculation...... and secondly the size of the contact. In the FE calculation the true gear tooth root profile is applied. The meshing stiffness’s of gears are highly non-linear, it is however found that the stiffness of an individual tooth can be expressed in a linear form assuming that the contact length is constant....

Research on Gear Shifting Process without Disengaging Clutch for a Parallel Hybrid Electric Vehicle Equipped with AMT

Directory of Open Access Journals (Sweden)

Hui-Long Yu

2014-01-01

Full Text Available Dynamic models of a single-shaft parallel hybrid electric vehicle (HEV equipped with automated mechanical transmission (AMT were described in different working stages during a gear shifting process without disengaging clutch. Parameters affecting the gear shifting time, components life, and gear shifting jerk in different transient states during a gear shifting process were deeply analyzed. The mathematical models considering the detailed synchronizer working process which can explain the gear shifting failure, long time gear shifting, and frequent synchronizer failure phenomenon in HEV were derived. Dynamic coordinated control strategy of the engine, motor, and actuators in different transient states considering the detailed working stages of synchronizer in a gear shifting process of a HEV is for the first time innovatively proposed according to the state of art references. Bench test and real road test results show that the proposed control strategy can improve the gear shifting quality in all its evaluation indexes significantly.

HOW TO STEER THE TRANSMISSION RATIO OF PLANETARY CONTINUOUSLY ADJUSTABLE GEAR TRAIN

Directory of Open Access Journals (Sweden)

A. M. Dankov

2016-01-01

Full Text Available The known attempts to create a continuously-adjustable gear train with solid gears have led to development of some so-called adaptive gears. The most structurally simple version of continuously- adjustable gear train is a two-wheel planetary gear. It is an obvious fact that an active regulation of gear ratio for the gear should be based on the presence of con- trolled elements (parameters and a mechanism for their control. In respect of the mentioned gear one of the controlled elements that is a compound central toothed gear has such controlled parameter as a nominal pitch diameter. In this case it can rotate or remain motionless. Other controlled element which is a planetary carrier has its own radius as a controlled parameter and makes a rotary motion with a great speed of a leading element. The purpose of the control mechanism is to ensure radial displacement of central toothed gear and planet gear sectors in the working gear. The paper describes the mechanism modifications and considers two variants for transfer of control action from its source to an object to be controlled. The transfer is ensured by mechanical gears (two variants and hydraulics.

Buckling of anisotropic films on cylindrical substrates: insights for self-assembly fabrication of 3D helical gears

International Nuclear Information System (INIS)

Yin Jie; Chen Xi

2010-01-01

We propose an effective way of fabricating true three-dimensional helical gear-like structures (with inclined gear teeth) by using self-assembled stress-driven buckling of anisotropic films on compliant cylindrical substrates. Key parameters characterizing the helical undulation profile, in particular the gear teeth number and the inclined teeth angle, are investigated numerically using finite element simulations. Based on the insights from numerical calculations, a simplified theoretical model is established to effectively predict the teeth number. The results show that the anisotropic modulus ratio has a larger effect on the teeth number than the anisotropy angle. The orientation of gear teeth is related to the coupled effects of the anisotropic modulus ratio, anisotropy angle, substrate curvature and substrate aspect ratio. In general, the undulation orientation tends to be perpendicular to the direction of minimum bending stiffness in the film. The findings in this paper provide useful guidance for the self-assembly fabrication of helical gears and other 3D structures at various length scales.

Group-Effort Applied Research (GEAR): Expanding Opportunities for Undergraduate Research Through Original, Class-Based Research Projects

Science.gov (United States)

Moore, Sean D.; Teter, Ken

2014-01-01

Undergraduate research clearly enriches the educational development of participating students, but these experiences are limited by the inherent inefficiency of the standard one student - one mentor model for undergraduate research. Group-Effort Applied Research (GEAR) was developed as a strategy to provide substantial numbers of undergraduates with meaningful research experiences. The GEAR curriculum delivers concept-driven lecture material and provides hands-on training in the context of an active research project from the instructor's lab. Because GEAR is structured as a class, participating students benefit from intensive, supervised research training that involves a built-in network of peer support and abundant contact with faculty mentors. The class format also ensures a relatively standardized and consistent research experience. Furthermore, meaningful progress toward a research objective can be achieved more readily with GEAR than with the traditional one student - one mentor model of undergraduate research because sporadic mistakes by individuals in the class are overshadowed by the successes of the group as a whole. Three separate GEAR classes involving three distinct research projects have been offered to date. In this paper, we provide an overview of the GEAR format and review some of the recurring themes for GEAR instruction. We propose GEAR can serve as a template to expand student opportunities for life science research without sacrificing the quality of the mentored research experience. PMID:24898007

3000-HP Roller Gear Transmission Development Program. Volume 3. Roller Gear Manufacture

Science.gov (United States)

1975-07-01

power is fed through the ramp roller clutch type free- wheel units to spur gears which mesh with the combining spur gear whose centerline is common...when the engine tends to turn faster than the main rotor shaft. It is in the free- wheel mode when the main rotor shaft tends to turn faster than the...gears are cut progrind at this time. Check face runout on each end of largo gears. Not to exceed .002" TIR 30 EBW one end 40 EBW opposite end

49 CFR 230.89 - Reverse gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Reverse gear. 230.89 Section 230.89 Transportation... Reversing Gear § 230.89 Reverse gear. (a) General provisions. Reverse gear, reverse levers, and quadrants... quadrant. Proper counterbalance shall be provided for the valve gear. (b) Air-operated power reverse gear...

Identification of the Onset of Cracking in Gear Teeth Using Acoustic Emission

International Nuclear Information System (INIS)

Pullin, R; Clarke, A; Eaton, M J; Pearson, M R; Holford, K M

2012-01-01

The development of diagnostic methods for gear tooth faults in aerospace power transmission systems is an active research area being driven largely by the interests of military organisations or large aerospace organisations. In aerospace applications, the potential results of gear failure are serious, ranging from increased asset downtime to, at worst, catastrophic failure with life-threatening consequences. New monitoring techniques which can identify the onset of failure at earlier stages are in demand. Acoustic Emission (AE) is the most sensitive condition monitoring tool and is a passive technique that detects the stress wave emitted by a structure as cracks propagate. In this study a gear test rig that allows the fatigue loading of an individual gear tooth was utilised. The rig allows a full AE analysis of damage signatures in gear teeth without the presence of constant background noise due to rotational and frictional sources. Furthermore this approach allows validation of AE results using crack gauges or strain gauges. Utilising a new approach to AE monitoring a sensor was mounted on the gear and used to continuously capture AE data for a complete fatigue load cycle of data, rather than the traditional approach where discrete signals are captured on a threshold basis. Data was captured every 10th load cycle for the duration of the test. A developed fast fourier transform analysis technique was compared with traditional analytical methods. In this investigation the developed techniques were validated against visual inspection and were shown to be far superior to the traditional approach.

The cycloid Permanent Magnetic Gear

DEFF Research Database (Denmark)

Rasmussen, Peter Omand; Andersen, Torben Ole; Jørgensen, Frank T.

2008-01-01

This paper presents a new permanent-magnet gear based on the cycloid gearing principle. which normally is characterized by an extreme torque density and a very high gearing ratio. An initial design of the proposed magnetic gear was designed, analyzed, and optimized with an analytical model...... regarding torque density. The results were promising as compared to other high-performance magnetic-gear designs. A test model was constructed to verify the analytical model....

Correlation of Gear Surface Fatigue Lives to Lambda Ratio (Specific Film Thickness)

Science.gov (United States)

Krantz, Timothy Lewis

2013-01-01

The effect of the lubrication regime on gear performance has been recognized, qualitatively, for decades. Often the lubrication regime is characterized by the specific film thickness being the ratio of lubricant film thickness to the composite surface roughness. Three studies done at NASA to investigate gearing pitting life are revisited in this work. All tests were done at a common load. In one study, ground gears were tested using a variety of lubricants that included a range of viscosities, and therefore the gears operated with differing film thicknesses. In a second and third study, the performance of gears with ground teeth and superfinished teeth were assessed. Thicker oil films provided longer lives as did improved surface finish. These datasets were combined into a common dataset using the concept of specific film thickness. This unique dataset of more 258 tests provides gear designers with some qualitative information to make gear design decisions.

Tooth contact analysis of spur gears. Part 2-Analysis of modified gears

Directory of Open Access Journals (Sweden)

Pop Nicolae

2017-01-01

Full Text Available The misalignment between gears axes or direction deviations of teeth leads accentuate the edge effect, Modified spur gears which localize the initial bearing contact by proper modifications of the lead profile are used to avoid the development of the edge effect. A semi-analytical method was involved to find the contact area, pressures distribution and depth stresses states for the standard gears and gears with modified lead profile. The lead modifications concerned the crowning of the flank surface and the end relieving of the tooth flanks, both being applied to the pinion teeth only.

Research of Planetary Gear Fault Diagnosis Based on Permutation Entropy of CEEMDAN and ANFIS

NARCIS (Netherlands)

Kuai, Moshen; Cheng, Gang; Pang, Y.; Li, Yong

2018-01-01

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear

Numerical Calculation and Experiment of Coupled Dynamics of the Differential Velocity Vane Pump Driven by the Hybrid Higher-order Fourier Non-circular Gears

Science.gov (United States)

Xu, Gaohuan; Chen, Jianneng; Zhao, Huacheng

2018-06-01

The transmission systems of the differential velocity vane pumps (DVVP) have periodic vibrations under loads. And it is not easy to find the reason. In order to optimize the performance of the pump, the authors proposed DVVP driven by the hybrid Higher-order Fourier non-circular gears and tested it. There were also similar periodic vibrations and noises under loads. Taking into account this phenomenon, the paper proposes fluid mechanics and solid mechanics simulation methodology to analyze the coupling dynamics between fluid and transmission system and reveals the reason. The results show that the pump has the reverse drive phenomenon, which is that the blades drive the non-circular gears when the suction and discharge is alternating. The reverse drive phenomenon leads the sign of the shaft torque to be changed in positive and negative way. So the transmission system produces torsional vibrations. In order to confirm the simulation results, micro strains of the input shaft of the pump impeller are measured by the Wheatstone bridge and wireless sensor technology. The relationships between strain and torque are obtained by experimental calibration, and then the true torque of input shaft is calculated indirectly. The experimental results are consistent to the simulation results. It is proven that the periodic vibrations are mainly caused by fluid solid coupling, which leads to periodic torsional vibration of the transmission system.

Working memory-driven attention improves spatial resolution: Support for perceptual enhancement.

Science.gov (United States)

Pan, Yi; Luo, Qianying; Cheng, Min

2016-08-01

Previous research has indicated that attention can be biased toward those stimuli matching the contents of working memory and thereby facilitates visual processing at the location of the memory-matching stimuli. However, whether this working memory-driven attentional modulation takes place on early perceptual processes remains unclear. Our present results showed that working memory-driven attention improved identification of a brief Landolt target presented alone in the visual field. Because the suprathreshold target appeared without any external noise added (i.e., no distractors or masks), the results suggest that working memory-driven attention enhances the target signal at early perceptual stages of visual processing. Furthermore, given that performance in the Landolt target identification task indexes spatial resolution, this attentional facilitation indicates that working memory-driven attention can boost early perceptual processing via enhancement of spatial resolution at the attended location.

Dynamic Analysis for a Geared Turbofan Engine with Variable Area Fan Nozzle

Science.gov (United States)

Csank, Jeffrey T.; Thomas, George L.

2017-01-01

Aggressive design goals have been set for future aero-propulsion systems with regards to fuel economy, noise, and emissions. To meet these challenging goals, advanced propulsion concepts are being explored and current operating margins are being re-evaluated to find additional concessions that can be made. One advanced propulsion concept being evaluated is a geared turbofan with a variable area fan nozzle (VAFN), developed by NASA. This engine features a small core, a fan driven by the low pressure turbine through a reduction gearbox, and a shape memory alloy (SMA)-actuated VAFN. The VAFN is designed to allow both a small exit area for efficient operation at cruise, while being able to open wider at high power conditions to reduce backpressure on the fan and ensure a safe level of stall margin is maintained. The VAFN is actuated via a SMA-based system instead of a conventional system to decrease overall weight of the system, however, SMA-based actuators respond relatively slowly, which introduces dynamic issues that are investigated in this work. This paper describes both a control system designed specifically for issues associated with SMAs, and dynamic analysis of the geared turbofan VAFN with the SMA actuators. Also, some future recommendations are provided for this type of propulsion system.

Contact stress analysis of involute spur gear by Finite Element ...

African Journals Online (AJOL)

In this paper the contact stress in rolling-sliding contact of involute spur gear and the effect of coefficient of friction was analyzed. To achieve this, first, three dimensional involute spur gear pairs were developed in Solid works 2012 Premium and the 3D model was exported to ANSYS workbench 14.5. Next, the analysis was ...

Interlocking Molecular Gear Chains Built on Surfaces.

Science.gov (United States)

Zhao, Rundong; Qi, Fei; Zhao, Yan-Ling; Hermann, Klaus E; Zhang, Rui-Qin; Van Hove, Michel A

2018-05-17

Periodic chains of molecular gears in which molecules couple with each other and rotate on surfaces have been previously explored by us theoretically using ab initio simulation tools. On the basis of the knowledge and experience gained about the interactions between neighboring molecular gears, we here explore the transmission of rotational motion and energy over larger distances, namely, through a longer chain of gear-like passive "slave" molecules. Such microscopic gears exhibit quite different behaviors compared to rigid cogwheels in the macroscopic world due to their structural flexibility affecting intermolecular interaction. Here, we investigate the capabilities of such gear chains and reveal the mechanisms of the transmission process in terms of both quantum-level density functional theory (DFT) and simple classical mechanics. We find that the transmission of rotation along gear chains depends strongly on the gear-gear distance: short distances can cause tilting of gears and even irregular "creep-then-jump" (or "stick-slip") motion or expulsion of gears; long gear-gear distances cause weak coupling between gears, slipping and skipping. More importantly, for transmission of rotation at intermediate gear-gear distances, our modeling clearly exhibits the relative roles of several important factors: flexibility of gear arms, axles, and supports, as well as resulting rotational delays, slippages, and thermal and other effects. These studies therefore allow better informed design of future molecular machine components involving motors, gears, axles, etc.

Partial tooth gear bearings

Science.gov (United States)

Vranish, John M. (Inventor)

2010-01-01

A partial gear bearing including an upper half, comprising peak partial teeth, and a lower, or bottom, half, comprising valley partial teeth. The upper half also has an integrated roller section between each of the peak partial teeth with a radius equal to the gear pitch radius of the radially outwardly extending peak partial teeth. Conversely, the lower half has an integrated roller section between each of the valley half teeth with a radius also equal to the gear pitch radius of the peak partial teeth. The valley partial teeth extend radially inwardly from its roller section. The peak and valley partial teeth are exactly out of phase with each other, as are the roller sections of the upper and lower halves. Essentially, the end roller bearing of the typical gear bearing has been integrated into the normal gear tooth pattern.

Modelling the Meshing of Cycloidal Gears

Directory of Open Access Journals (Sweden)

Nachimowicz Jerzy

2016-06-01

Full Text Available Cycloidal drives belong to the group of planetary gear drives. The article presents the process of modelling a cycloidal gear. The full profile of the planetary gear is determined from the following parameters: ratio of the drive, eccentricity value, the equidistant (ring gear roller radius, epicycloid reduction ratio, roller placement diameter in the ring gear. Joong-Ho Shin’s and Soon-Man Kwon’s article (Shin and Know, 2006 was used to determine the profile outline of the cycloidal planetary gear lobes. The result was a scatter chart with smooth lines and markers, presenting the full outline of the cycloidal gear.

Children's Headache: Drawings in the Diagnostic Work Up.

Science.gov (United States)

Mazzotta, Silvia; Pavlidis, Elena; Cordori, Cecilia; Spagnoli, Carlotta; Pini, Luigi Alberto; Pisani, Francesco

2015-08-01

This study aims to evaluate the drawings effectiveness in childhood headache assessment. Headache is a common cause of pain in children. Although drawings have been used in childhood to recognize psychological insights and pain perception, they were rarely used for headache characterization. We collected drawings from 67 subjects with cephalalgia during a 22-month timeframe. The clinical diagnosis was made according to the 2nd edition of The International Headache Classification. Drawings were independently categorized as migraine or tension-type headache (TTH) by two child neuropsychiatrists blinded to the clinical data. Cohen kappa for interrater agreement, sensitivity, specificity, and positive predictive value (PPV) were calculated. Subjects were also divided into three age groups to assess the influence of age. Finally, a control group of 90 subjects was collected and K-means cluster analysis was performed. The drawings had a sensitivity of 85.71 and 81.48%, a specificity of 81.48 and 85.71%, and a PPV of 85.71 and 81.48%, for migraine and TTH diagnosis, respectively. Drawings by the older age group showed the highest predictability degree. Finally, by mean of cluster analysis, 59 of the 67 patients were correctly classified, whereas control subjects were similarly distributed between the two clusters. Drawings are a useful instrument for migraine and TTH differential diagnosis. Thus, we suggest their inclusion in childhood headache diagnostic assessment. Georg Thieme Verlag KG Stuttgart · New York.

Stuck in gear: age-related loss of variable gearing in skeletal muscle.

Science.gov (United States)

Holt, Natalie C; Danos, Nicole; Roberts, Thomas J; Azizi, Emanuel

2016-04-01

Skeletal muscles power a broad diversity of animal movements, despite only being able to produce high forces over a limited range of velocities. Pennate muscles use a range of gear ratios, the ratio of muscle shortening velocity to fiber shortening velocity, to partially circumvent these force-velocity constraints. Muscles operate with a high gear ratio at low forces; fibers rotate to greater angles of pennation, enhancing velocity but compromising force. At higher forces, muscles operate with a lower gear ratio; fibers rotate little so limiting muscle shortening velocity, but helping to preserve force. This ability to shift gears is thought to be due to the interplay of contractile force and connective tissue constraints. In order to test this hypothesis, gear ratios were determined in the medial gastrocnemius muscles of both healthy young rats, and old rats where the interaction between contractile and connective tissue properties was assumed to be disrupted. Muscle fiber and aponeurosis stiffness increased with age (PGear ratio decreased with increasing force in young (Pgearing is lost in old muscle. These findings support the hypothesis that variable gearing results from the interaction between contractile and connective tissues and suggest novel explanations for the decline in muscle performance with age. © 2016. Published by The Company of Biologists Ltd.

Scientific drawing: an introduction to drawing as a language in fieldwork

Directory of Open Access Journals (Sweden)

José Mayor Iborra

2013-11-01

Full Text Available The scientific drawing understood as a universal language is a tool of undoubted documentary value as well as daily use in our field work of any professional who is with the need to register with graphics, a work process in which, need to process the drawing as coach and illustrator information. The drawings scientists have always had the vocation of fidelity and accuracy, in order to collect objective truths. The scientific drawing has been compressed and discriminating, as the reading order of the drawing through the line by providing a clear exposition that the photograph is not enough to achieve.

Design and construction of permanent magnetic gears

DEFF Research Database (Denmark)

Jørgensen, Frank Thorleif

/l]. Measurement from this gear has resulted in a measured total torque density of 23 [Nm/l]. Mechanical versions of this gear type are found with total torque density in the 16 to 31 [Nm/l] range. The third and last gear technology that is investigated is a gear that reminds of a planetary gear. Research shows......This thesis deals with design and development of permanent magnetic gears. The goal of this thesis is to develop knowledge and calculation software for magnetic gears. They use strong NdFeB permanent magnets and a new magnetic gear technology, which will be a serious alternative to classical...... mechanical gears. The new magnetic gear will have a high torque density1 relationship –high efficiency and are maintenance free. In this project was manufactured two test gears which is tested and verified with models developed in this project. Present technological status for magnetic gears is introduced...

D Modelling with the Samsung Gear 360

Science.gov (United States)

Barazzetti, L.; Previtali, M.; Roncoroni, F.

2017-02-01

The Samsung Gear 360 is a consumer grade spherical camera able to capture photos and videos. The aim of this work is to test the metric accuracy and the level of detail achievable with the Samsung Gear 360 coupled with digital modelling techniques based on photogrammetry/computer vision algorithms. Results demonstrate that the direct use of the projection generated inside the mobile phone or with Gear 360 Action Direction (the desktop software for post-processing) have a relatively low metric accuracy. As results were in contrast with the accuracy achieved by using the original fisheye images (front and rear facing images) in photogrammetric reconstructions, an alternative solution to generate the equirectangular projections was developed. A calibration aimed at understanding the intrinsic parameters of the two lenses camera, as well as their relative orientation, allowed one to generate new equirectangular projections from which a significant improvement of geometric accuracy has been achieved.

Quantum work distribution for a driven diatomic molecule

International Nuclear Information System (INIS)

Leonard, Alison; Deffner, Sebastian

2015-01-01

Highlights: • A method for calculating the time-dependent solution for a driven system is proposed. • These solutions are used to compute the quantum work distribution. • This distribution is calculated for the Morse potential mimicking a diatomic molecule. • Due to bound and scattering states distribution exhibits continuous and discrete part. • Result is compared with that of a harmonic approximation. - Abstract: We compute the quantum work distribution for a driven Morse oscillator. To this end, we solve the time-dependent dynamics for a scale-invariant process, from which the exact expressions for the transition probabilities are found. Special emphasis is put on the contributions to the work distribution from discrete (bound) and continuous (scattering) parts of the spectrum. The analysis is concluded by comparing the work distribution for the exact Morse potential and the one resulting from a harmonic approximation

Hydrostatic self-locking bevel differential gear; Hydrostatisch selbstsperrendes Kegelraddifferentialgetriebe

Energy Technology Data Exchange (ETDEWEB)

Kalmbach, K.

2001-07-01

The product range of the rail vehicle industry comprises the construction of railroad material for long-distance and short-distance transport. This includes, for example, locomotives and cars, subway, light railway and tramway cars as well as rail vehicle equipment. The development of the industry is determined by the demand for transport services and government actions for the extension of railways and procurement of suitable vehicle types. In contrast to road vehicles, differential gears are only used in a negligible percentage of rail vehicles. Primarily in the short-distance rail transport sector, the demand for differential gears is growing due to increased drive power, smaller wheel diameters, lower vehicle mass with higher load capacity, the introduction of low-floor technology as well as the requirement of employing ever more quiet vehicles. In hydrostatic self-locking differential gears, oil is supplied to the gears within the differential gearbox. They only rotate relative to each other when the differential gear performs a compensation movement. In this case, oil is transported in the tooth space to the meshing of the gears, where it is displaced due to the meshing and must drain through tight gaps. The pressure generated by this process acts against the compensation movement of the gear, and the drive torque is transmitted to the wheel that has the higher friction. The achievable locking torque is linearly dependent on the differential speed of the drive wheel. This locking effect is achieved without wear-prone components and works automatically without active external intervention. The design space required corresponds to that of conventional differential gears, as the locking effect is integrated in the existing design. (orig.)

Analysis of an employment of a gear ratio rate in CVT control system

Science.gov (United States)

Grzegożek, W.; Szczepka, M.

2016-09-01

Continuously variable transmissions(CVTs) potentially ensure the selection of such a gear ratio that scooter fuel consumption can reach minimum value. Traditionally these CVT gearboxes are mechanically controlled, causing a gear ratio to be an engine revs function. This solution does not ensure optimum gear ratio. In this paper the solution for fuel optimal control problem is presented. The results obtained during brake stand research of scooter powertrains show the significant values of brake specific fuel consumption for the velocity that is maximum for a scooter according to highway code. With the introduction of CVT gearbox in which the selection of gear ratio can be controlled according to the worked out strategy the solution for fuel consumption problem is possible. Electromechanical actuators ensure the selection of a gear ratio independently of engine revs. Such type of construction solution makes working out the suitable control strategy that ensures decreasing of scooter fuel consumption possible. Presented strategies do not use precise optimization techniques. The CVT efficiency has a strong influence on transient operation. In the paper the control strategy owing to which fuel consumption decreases by over 40% is presented. The strategy was worked out on the basis of fuel consumption map for a defined scooter exploitation model. The possibilities of realization of the worked out strategy were tested on the brake test stand.

Modelling of teeth of a gear transmission for modern manufacturing technologies

Science.gov (United States)

Monica, Z.; Banaś, W.; Ćwikla, G.; Topolska, S.

2017-08-01

The technological process of manufacturing of gear wheels is influenced by many factors. It is designated depending on the type of material from which the gear is to be produced, its heat treatment parameters, the required accuracy, the geometrical form and the modifications of the tooth. Therefor the parameters selection process is not easy and moreover it is unambiguous. Another important stage of the technological process is the selection of appropriate tools to properly machine teeth in the operations of both roughing and finishing. In the presented work the focus is put first of all on modern production methods of gears using technologically advanced instruments in comparison with conventional tools. Conventional processing tools such as gear hobbing cutters or Fellows gear-shaper cutters are used from the beginning of the machines for the production of gear wheels. With the development of technology and the creation of CNC machines designated for machining of gears wheel it was also developed the manufacturing technology as well as the design knowledge concerning the technological tools. Leading manufacturers of cutting tools extended the range of tools designated for machining of gears on the so-called hobbing cutters with inserted cemented carbide tips. The same have be introduced to Fellows gear-shaper cutters. The results of tests show that is advantaged to use hobbing cutters with inserted cemented carbide tips for milling gear wheels with a high number of teeth, where the time gains are very high, in relation to the use of conventional milling cutters.

Research of grinding process of gears with involute profile to increase its efficiency

Science.gov (United States)

Ivanova, T. N.; Korshunov, A. I.; Sannikov, I. N.; Tyukpiekov, V. N.

2018-03-01

Grinding as final processing exerts great influence on quality and accuracy of a surface layer of gears. Gear grinding is the most productive method of abrasive processing providing gears of 3 - 8 degrees of accuracy. However violation of the temperature condition of grinding leads to emergence of burns on the surfaces of gears. Therefore the research of the reasons generating defects and finding the ways of their elimination are relevant. The work presents the research of involute tooth profile grinding by wheels of different types with different ways to form a surface. For every way the movements of a tool and a workpiece in order to receive a contour of the tooth socket are simulated. The advantages and the shortcomings of the tooth grinding using form wheels in a grinding method and using dish, worm wheels in generating the grinding method are revealed. The experience of gear production shows that availability of burns in the certain part of a tooth profile is caused by features of the gear grinding process. Theoretical and experimental researches of the thermal phenomena of gear grinding with different configurations of spots in a contact zone and a trajectory of their movement are conducted. There are recommendations how to choose grinding modes, characteristics of abrasive tools taking into account a non-burnt condition of a working surface of a gear. The right choice of lubricating fluid and the way of its supply greatly affect the efficiency of the gear grinding process. It is established that lubricating fluid with special additives gives the best results to obtain desired roughness of a processed surface. The recommendations of effective fluids and their foreign analogs are made.

Systems and Methods for Implementing Bulk Metallic Glass-Based Strain Wave Gears and Strain Wave Gear Components

Science.gov (United States)

Hofmann, Douglas C. (Inventor); Wilcox, Brian (Inventor)

2016-01-01

Bulk metallic glass-based strain wave gears and strain wave gear components. In one embodiment, a strain wave gear includes: a wave generator; a flexspline that itself includes a first set of gear teeth; and a circular spline that itself includes a second set of gear teeth; where at least one of the wave generator, the flexspline, and the circular spline, includes a bulk metallic glass-based material.

Five-Axis Milling of Large Spiral Bevel Gears: Toolpath Definition, Finishing, and Shape Errors

Directory of Open Access Journals (Sweden)

Álvaro Álvarez

2018-05-01

Full Text Available In this paper, a five-axis machining process is analyzed for large spiral-bevel gears, an interesting process for one-of-kind manufacturing. The work is focused on large sized spiral bevel gears manufacturing using universal multitasking machines or five-axis milling centers. Different machining strategies, toolpath patterns, and parameters are tested for both gear roughing and finishing operations. Machining time, tools’ wear, and gear surface are analyzed in order to determine which are the best strategies and parameters for large modulus gear manufacturing on universal machines. The case study results are discussed in the last section, showing the capacity of a universal five-axis milling for this niche. Special attention was paid to the possible affectations of the metal surfaces, since gear durability is very sensitive to thermo-mechanical damage, affected layers, and flank gear surface state.

Gear Tooth Wear Detection Algorithm

Science.gov (United States)

Delgado, Irebert R.

2015-01-01

Vibration-based condition indicators continue to be developed for Health Usage Monitoring of rotorcraft gearboxes. Testing performed at NASA Glenn Research Center have shown correlations between specific condition indicators and specific types of gear wear. To speed up the detection and analysis of gear teeth, an image detection program based on the Viola-Jones algorithm was trained to automatically detect spiral bevel gear wear pitting. The detector was tested using a training set of gear wear pictures and a blind set of gear wear pictures. The detector accuracy for the training set was 75 percent while the accuracy for the blind set was 15 percent. Further improvements on the accuracy of the detector are required but preliminary results have shown its ability to automatically detect gear tooth wear. The trained detector would be used to quickly evaluate a set of gear or pinion pictures for pits, spalls, or abrasive wear. The results could then be used to correlate with vibration or oil debris data. In general, the program could be retrained to detect features of interest from pictures of a component taken over a period of time.

Advanced Face Gear Surface Durability Evaluations

Science.gov (United States)

Lewicki, David G.; Heath, Gregory F.

2016-01-01

The surface durability life of helical face gears and isotropic super-finished (ISF) face gears was investigated. Experimental fatigue tests were performed at the NASA Glenn Research Center. Endurance tests were performed on 10 sets of helical face gears in mesh with tapered involute helical pinions, and 10 sets of ISF-enhanced straight face gears in mesh with tapered involute spur pinions. The results were compared to previous tests on straight face gears. The life of the ISF configuration was slightly less than that of previous tests on straight face gears. The life of the ISF configuration was slightly greater than that of the helical configuration.

On gear tooth stiffness evaluation

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard; Jørgensen, Martin Felix

2014-01-01

The estimation of gear stiffness is important for determining the load distribution between the gear teeth when two sets of teeth are in contact. Two factors have a major influence on the stiffness; firstly the boundary condition through the gear rim size included in the stiffness calculation...

Technologies for the marking of fishing gear to identify gear components entangled on marine animals and to reduce abandoned, lost or otherwise discarded fishing gear.

Science.gov (United States)

He, Pingguo; Suuronen, Petri

2018-04-01

Fishing gears are marked to establish and inform origin, ownership and position. More recently, fishing gears are marked to aid in capacity control, reduce marine litter due to abandoned, lost or otherwise discarded fishing gear (ALDFG) and assist in its recovery, and to combat illegal, unreported and unregulated (IUU) fishing. Traditionally, physical marking, inscription, writing, color, shape, and tags have been used for ownership and capacity purposes. Buoys, lights, flags, and radar reflectors are used for marking of position. More recently, electronic devices have been installed on marker buoys to enable easier relocation of the gear by owner vessels. This paper reviews gear marking technologies with focus on coded wire tags, radio frequency identification tags, Automatic Identification Systems, advanced electronic buoys for pelagic longlines and fish aggregating devices, and re-location technology if the gear becomes lost. Copyright © 2018 Elsevier Ltd. All rights reserved.

29 CFR 1918.54 - Rigging gear.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Rigging gear. 1918.54 Section 1918.54 Labor Regulations...) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Vessel's Cargo Handling Gear § 1918.54 Rigging gear. (a... other alternate device shall be provided to allow trimming of the gear and to prevent employees from...

Possiblity of substituting 12XH3A steel in the manufacture of gears for a Sova motorcycle gearing box

Science.gov (United States)

Abramov, L. M.; Karabanov, V. P.; Abramov, V. L.; Astakhin, A. S.

1996-03-01

The experimental work describes the possibility of substituting the expensive alloying steel 12XH3A for the low-cost material (steel 40X) in manufacturing gears of the motor cycle gearing box. It ban be achieved on the basis of the obtained results and with the help of laser melting treatment of small-alloying steel. We can speak about the dependence of laser melting radiation efficiency on the regimes and procedures. The breakage of the gearing box of the motor cycle 'Sova' may be explained by the low carry ability of its first gearing box gear. This investigation includes the determination of the cause of this problem. One of the most wide spread methods of such decisions is the substitution of the used materials by another. The most important criteria for the new materials are: (1) the increase of mechanical characteristics (solidity, plasticity); (2) the increase of such characteristics as hardness, specific percussive viscosity; (3) the improvement of the technological characteristics; (4) the condencention of the manufacturing expenditures (economical effect). In accordance with these creations some materials (35X, 40X, 20XH, 40XHM steels) were chosen. The best material is 40X steel, because it allows us to treat the gears by laser radiation with the surface melt. Surface melt allows us to produce: (1) martensite structure with high solidity and low percussive viscosity; (2) martensite structure with chrome carbides and high percussive viscosity, but low plasticity; (3) amorphous or monocrystallic structures with the best characteristics. The last structure has the best characteristics because dislocation defects in such material are practically absent. Also, the amorphous surface of the materials is the most interesting. The spirit of the investigation is to define the parameters of production such as radiation power, size of laser spot, and speed of spot.

Finishing aeronautical planetary herringbone gear wheels in container vibrating smoothing machine

Directory of Open Access Journals (Sweden)

Jacek MICHALSKI

2015-12-01

Full Text Available The paper presents the technological process of abrasive-chemical machining wheel bearing surface of the cylindrical herringbone gears planetary gear in vibrating container smoothing machine according to Isotropic Finishing ISF® technology of the REM Chemicals Inc. company. Gear wheels are made of stainless Pyrowear 53 and subjected to carburizing, hardening, cold working and low tempering. The change in value of deviation indicators for the kinematic accuracy, smoothness and geometric structure of the machined surfaces of the gear teeth after smoothing compared with the contoured grinding were analyzed. The findings are different a characteristic performance on the surface of the tooth side along the outline, especially with a higher value at the head of the tooths. This creates a need for appropriate modification of the lateral surface of the teeth in the process of contoured grinding. The results of the mechanical strength of the samples gear wheel after the smoothing process and evaluating the hydrogen embrittlement are presented.

Holistic assessment of Chwaka Bay's multi-gear fishery - Using a trophic modeling approach

Science.gov (United States)

Rehren, Jennifer; Wolff, Matthias; Jiddawi, Narriman

2018-04-01

East African coastal communities highly depend on marine resources for not just income but also protein supply. The multi-species, multi-gear nature of East African fisheries makes this type of fishery particularly difficult to manage, as there is a trade-off between maximizing total catch from all gears and species and minimizing overfishing of target species and the disintegration of the ecosystem. The use and spatio-temporal overlap of multiple gears in Chwaka Bay (Zanzibar) has led to severe conflicts between fishermen. There is a general concern of overfishing in the bay because of the widespread use of small mesh sizes and destructive gears such as dragnets and spear guns. We constructed an Ecopath food web model to describe the current trophic flow structure and fishing pattern of the bay. Based on this model, we explored the impact of different gears on the ecosystem and the fishing community in order to give advice for gear based management in the bay. Results indicate that Chwaka bay is a productive, shallow water system, with biomass concentrations around the first and second trophic level. The system is greatly bottom-up driven and dominated by primary producers and invertebrates. The trophic and network indicators as well as the community energetics characterize Chwaka Bay as relatively mature. Traps and dragnets have the strongest impact on the ecosystem and on the catches obtained by other gears. Both gears potentially destabilize the ecosystem by reducing the biomass of top-down controlling key species (including important herbivores of macroalgae). The dragnet fishery is the least profitable, but provides most jobs for the fishing community. Thus, a complete ban of dragnets in the bay would require the provision of alternative livelihoods. Due to the low resource biomass of fish in the bay and the indication of a loss of structural control of certain fish groups, Chwaka Bay does not seem to provide scope for further expansion of the fishery

Shuttle Rudder/Speed Brake Power Drive Unit (PDU) Gear Scuffing Tests With Flight Gears

Science.gov (United States)

Proctor, Margaret P.; Oswald, Fred B.; Krants, Timothy L.

2005-01-01

Scuffing-like damage has been found on the tooth surfaces of gears 5 and 6 of the NASA space shuttle rudder/speed brake power drive unit (PDU) number 2 after the occurrence of a transient back-driving event in flight. Tests were conducted using a pair of unused spare flight gears in a bench test at operating conditions up to 2866 rpm and 1144 in.-lb at the input ring gear and 14,000 rpm and 234 in.-lb at the output pinion gear, corresponding to a power level of 52 hp. This test condition exceeds the maximum estimated conditions expected in a backdriving event thought to produce the scuffing damage. Some wear marks were produced, but they were much less severe than the scuffing damaged produced during shuttle flight. Failure to produce scuff damage like that found on the shuttle may be due to geometrical variations between the scuffed gears and the gears tested herein, more severe operating conditions during the flight that produced the scuff than estimated, the order of the test procedures, the use of new hydraulic oil, differences between the dynamic response of the flight gearbox and the bench-test gearbox, or a combination of these. This report documents the test gears, apparatus, and procedures, summarizes the test results, and includes a discussion of the findings, conclusions, and recommendations.

29 CFR 1919.19 - Gear requiring welding.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Gear requiring welding. 1919.19 Section 1919.19 Labor... (CONTINUED) GEAR CERTIFICATION Certification of Vessels' Cargo Gear § 1919.19 Gear requiring welding. Chains or other gear which have been lengthened, altered or repaired by welding shall be properly heat...

A Fault Diagnosis Approach for Gears Based on IMF AR Model and SVM

Directory of Open Access Journals (Sweden)

Yu Yang

2008-05-01

Full Text Available An accurate autoregressive (AR model can reflect the characteristics of a dynamic system based on which the fault feature of gear vibration signal can be extracted without constructing mathematical model and studying the fault mechanism of gear vibration system, which are experienced by the time-frequency analysis methods. However, AR model can only be applied to stationary signals, while the gear fault vibration signals usually present nonstationary characteristics. Therefore, empirical mode decomposition (EMD, which can decompose the vibration signal into a finite number of intrinsic mode functions (IMFs, is introduced into feature extraction of gear vibration signals as a preprocessor before AR models are generated. On the other hand, by targeting the difficulties of obtaining sufficient fault samples in practice, support vector machine (SVM is introduced into gear fault pattern recognition. In the proposed method in this paper, firstly, vibration signals are decomposed into a finite number of intrinsic mode functions, then the AR model of each IMF component is established; finally, the corresponding autoregressive parameters and the variance of remnant are regarded as the fault characteristic vectors and used as input parameters of SVM classifier to classify the working condition of gears. The experimental analysis results show that the proposed approach, in which IMF AR model and SVM are combined, can identify working condition of gears with a success rate of 100% even in the case of smaller number of samples.

Minimizing tooth bending stress in spur gears with simplified shapes of fillet and tool shape determination

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2015-01-01

by different standards, with the ISO standard probably being the most common one. Gears are manufactured using two principally different tools: rack tools and gear tools. In this work, the bending stress of involute teeth is minimized by shape optimization made directly on the final gear. This optimized shape...

50 CFR 697.23 - Restricted gear areas.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Restricted gear areas. 697.23 Section 697... Measures § 697.23 Restricted gear areas. (a) Resolution of lobster gear conflicts with fisheries managed...) Restricted Gear Area I—(1) Duration—(i) Mobile Gear. From October 1 through June 15 of each fishing year, no...

Creating a recollection-based memory through drawing.

Science.gov (United States)

Wammes, Jeffrey D; Meade, Melissa E; Fernandes, Myra A

2018-05-01

Drawing a picture of to-be-remembered information substantially boosts memory performance in free-recall tasks. In the current work, we sought to test the notion that drawing confers its benefit to memory performance by creating a detailed recollection of the encoding context. In Experiments 1 and 2, we demonstrated that for both pictures and words, items that were drawn by the participant at encoding were better recognized in a later test than were words that were written out. Moreover, participants' source memory (in this experiment, correct identification of whether the word was drawn or written) was superior for items drawn relative to written at encoding. In Experiments 3A and 3B, we used a remember-know paradigm to demonstrate again that drawn words were better recognized than written words, and further showed that this effect was driven by a greater proportion of recollection-, rather than familiarity-based responses. Lastly, in Experiment 4 we implemented a response deadline procedure, and showed that when recognition responses were speeded, thereby reducing participants' capacity for recollection, the benefit of drawing was substantially smaller. Taken together, our findings converge on the idea that drawing improves memory as a result of providing vivid contextual information which can be later called upon to aid retrieval. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Investigation on wear characteristic of biopolymer gear

Science.gov (United States)

Ghazali, Wafiuddin Bin Md; Daing Idris, Daing Mohamad Nafiz Bin; Sofian, Azizul Helmi Bin; Basrawi, Mohamad Firdaus bin; Khalil Ibrahim, Thamir

2017-10-01

Polymer is widely used in many mechanical components such as gear. With the world going to a more green and sustainable environment, polymers which are bio based are being recognized as a replacement for conventional polymers based on fossil fuel. The use of biopolymer in mechanical components especially gear have not been fully explored yet. This research focuses on biopolymer for spur gear and whether the conventional method to investigate wear characteristic is applicable. The spur gears are produced by injection moulding and tested on several speeds using a custom test equipment. The wear formation such as tooth fracture, tooth deformation, debris and weight loss was observed on the biopolymer spur gear. It was noted that the biopolymer gear wear mechanism was similar with other type of polymer spur gears. It also undergoes stages of wear which are; running in, linear and rapid. It can be said that the wear mechanism of biopolymer spur gear is comparable to fossil fuel based polymer spur gear, thus it can be considered to replace polymer gears in suitable applications.

Semi-automatic drawings surveying system

International Nuclear Information System (INIS)

Andriamampianina, Lala

1983-01-01

A system for the semi-automatic survey of drawings is presented. Its design has been oriented to the reduction of the stored information required for the drawing reproduction. This equipment consists mainly of a plotter driven by a micro-computer, but the pen of the plotter is replaced by a circular photodiode array. Line drawings are first viewed as a concatenation of vectors, with constant angle between the two vectors, and then divided in arcs of circles and line segments. A dynamic analysis of line intersections with the circular sensor permits to identify starting points and end points in a line, for the purpose of automatically following connected lines in drawing. The advantage of the method described is that precision practically depends only on the plotter performance, the sensor resolution being only considered for the thickness of strokes and the distance between two strokes. (author) [fr

Design of Gear Churning Power Loss Measurement Device

OpenAIRE

Wang Bin; Zhou Ya Jie; Wang Ping

2017-01-01

To explore the impacts of gear churning power losses, a research was conducted to achieve the internal causes of power losses of churning gear by designing a gear churning power losses measurement device. The gear churning power losses could be influenced by different gear modules, the number of teeth and the axial position of gear. Finally, the impacts of gear churning power losses were discussed by comparing experimental data and theoretical data.

New Siemens applications for designing bevel gears

Science.gov (United States)

Goanta, A. M.; Dumitrache, P.

2017-08-01

The current situation in the design of gearings is different from software to software and in some cases requires specialized settings with or without additional costs. There are two ways of generating evolving tooting: one is based on the designer’s solid knowledge of geometry and gearing and the other is based on a series of automation subprograms for 3D modelling of gears. The first method is a general one, applicable to all design software that is based on generating a curve evolving specific to a tooth flank, continued with the construction of the symmetrical flank, the pattern multiplication of circular type around the center of the gear and finally generation of the three-dimensional characteristic of each individual tooth. The second method is much faster and requires only general knowledge about the gear but sufficiently advanced to allow permanent dialogue with the subprogram for generating cone gears. Absolute novelty items are brought about by the new NX design applications that lead to getting gears with curved teeth. In conclusion the paper shows how different variants of bevel gears are generated using various subprograms or performance settings, installed over the SIEMENS NX. An essential component of the paper is highlighting generation capacity of gears and gearing intended for predefined types of gear cutting machines such as those for Gleason and Oerlikon teeth.

Examining the Abrasion Behaviour of PA 66 Gears in Different Cycles

Directory of Open Access Journals (Sweden)

Rifat Yakut

2014-01-01

Full Text Available Gears made of plastic-based materials are anticorrosive, resistant to magnetic environments, and light and have pulse decay, low noise, and self-lubrication properties, and therefore their usage areas are widening every single day. In this experiment, the working conditions of 30% fibreglass PA 66 (PA 66 GFR 30 plastic material with PA 66 (PA 66 GFR 30 plastic material and AISI 8620 couple gear are observed. Usage of PA 66 GFR 30 material as gear material at 56.75 Nm constant load and 750 rpm, 1000 rpm, and 1500 rpm was analysed. The load capacity damage formation of the material was also analysed. The tooth surface temperature, corrosion depth of the tooth profile, tooth damage, and the tooth surface were examined with an scanning electron microscopy (SEM and the corrosive behaviour of gears was analysed.

Tooth contact analysis of spur gears. Part 1-SAM analysis of standard gears

Directory of Open Access Journals (Sweden)

Creţu Spiridon

2017-01-01

Full Text Available The involute gears are sensitive to the misalignment of their axes which determines transmission errors and perturbations of pressures distributions along the tooth flank. The concentrated contacts in gears are no longer as Hertz type. A semi-analytical method was developed to find the contact area, pressures distribution and depth stresses state. The matrix of initial separations is found analytically for standard and non-standard spur gears. The presence of misalignment as well as the flank crowning and flank end relief are included in the numerical analysis process.

Research on the impact of surface properties of particle on damping effect in gear transmission under high speed and heavy load

Science.gov (United States)

Xiao, Wangqiang; Chen, Zhiwei; Pan, Tianlong; Li, Jiani

2018-01-01

The vibration and noise from gear transmission have great damage on the mechanical equipment and operators. Through inelastic collisions and friction between particles, the energy can be dissipated in gear transmission. A dynamic model of particle dampers in gear transmission was put forward in this paper. The performance of particle dampers in centrifugal fields under different rotational speeds and load was investigated. The surface properties such as the impact of coefficient of restitution and friction coefficient of the particle on the damping effect were analyzed and the total energy loss was obtained by discrete element method (DEM). The vibration from time-varying mesh stiffness was effectively reduced by particle dampers and the optimum coefficient of restitution was discovered under different rotational speeds and load. Then, a test bench for gear transmission was constructed, and the vibration of driven gear and driving gear were measured through a three-directional wireless acceleration sensor. The research results agree well with the simulation results. While at relatively high speed, smaller coefficient of restitution achieves better damping effect. As to friction coefficient, at relatively high speed, the energy dissipation climbs up and then declines with the increase of the friction coefficient. The results can provide guidelines for the application of particle damper in gear transmission.

3D MODELLING WITH THE SAMSUNG GEAR 360

Directory of Open Access Journals (Sweden)

L. Barazzetti

2017-02-01

Full Text Available The Samsung Gear 360 is a consumer grade spherical camera able to capture photos and videos. The aim of this work is to test the metric accuracy and the level of detail achievable with the Samsung Gear 360 coupled with digital modelling techniques based on photogrammetry/computer vision algorithms. Results demonstrate that the direct use of the projection generated inside the mobile phone or with Gear 360 Action Direction (the desktop software for post-processing have a relatively low metric accuracy. As results were in contrast with the accuracy achieved by using the original fisheye images (front and rear facing images in photogrammetric reconstructions, an alternative solution to generate the equirectangular projections was developed. A calibration aimed at understanding the intrinsic parameters of the two lenses camera, as well as their relative orientation, allowed one to generate new equirectangular projections from which a significant improvement of geometric accuracy has been achieved.

Organigraphs: drawing how companies really work.

Science.gov (United States)

Mintzberg, H; Van der Heyden, L

1999-01-01

Walk into any organization and you will get a snapshot of the company in action--people and products moving every which way. But ask for a picture of the company and you will be given the org chart, with its orderly little boxes showing just the names and titles of managers. Now there's a more revealing way to depict the people and operations within an organization--an approach called the organigraph. The organigraph is not a chart. It's a map that offers an overview of the company's functions and the ways that people organize themselves at work. Perhaps most important, an organigraph can help managers see untapped competitive opportunities. Drawing on the organigraphs they created for about a dozen companies, authors Mintzberg and Van der Heyden illustrate just how valuable a tool the organigraph is. For instance, one they created for Electrocomponents, a British distributor of electrical and mechanical items, led managers to a better understanding of the company's real expertise--business-to-business relationships. As a result of that insight, the company wisely decided to expand in Asia and to increase its Internet business. As one manager says, "It allowed the company to see all sorts of new possibilities." With traditional hierarchies vanishing and newfangled--and often quite complex--organizational forms taking their place, people are struggling to understand how their companies work. What parts connect to one another? How should processes and people come together? Whose ideas have to flow where? With their flexibility and realism, organigraphs give managers a new way to answer those questions.

DETERMINATION OF TRANSMISSION GEAR RATIO IN MECHANICAL PART OF TRACTOR ELECTRO-MECHANICAL TRANSMISSION

Directory of Open Access Journals (Sweden)

Ch. I. Zhdanovich

2016-01-01

Full Text Available A methodology has been developed for selection of gear number and transmission gear ratios in mechanical part of a wheel-type tractor with electro-mechanical transmission containing a propulsion asynchronous electric motor with variablefrequency control. The paper proposes to determine a transmission gear ratio on the basis of the following: provision of wheel torque dependence on tractor speed which is the best one for a traction process and during transfer from one gear to the other; provision of nominal operational mode of the electric motor for all tractor operations where it is working for a long period of time; provision of minimum possible number of gears; complete realization of internal combustion engine power on the tractor wheels at limit operational mode of the electric motor. As a characteristic of the asynchronous electric motor with variable-frequency control contains various portions which can be used either completely or partially due to operating conditions, the gear number is determined in the process of transmission gear ration finding but not prior to this. A wheel torque of the tractor with electro-mechanical transmission can be limited according to the following factors: grip of wheel with supporting surface; maximum power of an internal combustion engine which can be transferred to the wheels and a torque which is developed by a propulsion electric motor. It is not proposed to exceed nominal operational mode of the propulsion electric motor for all the operations of the tractor if it is working for a long period of time because in the case of significant excess of the nominal operational mode of the asynchronous electric motor its rather long operation leads to low efficiency and high losses in power, large heat liberation and consequently requires to develop more complicated system for electric motor cooling. An excess of nominal electric motor torque can be justified for short-term operational modes because in this case

340 and 310 drawing field verification

International Nuclear Information System (INIS)

Langdon, J.

1996-01-01

The purpose of the drawing field verification work plan is to provide reliable drawings for the 310 Treated Effluent Disposal Facility (TEDF) and 340 Waste Handling Facility (340 Facility). The initial scope of this work plan is to provide field verified and updated versions of all the 340 Facility essential drawings. This plan can also be used for field verification of any other drawings that the facility management directs to be so updated. Any drawings revised by this work plan will be issued in an AutoCAD format

Experimental Investigations of Noise Control in Planetary Gear Set by Phasing

Directory of Open Access Journals (Sweden)

S. H. Gawande

2014-01-01

Full Text Available Now a days reduction of gear noise and resulting vibrations has received much attention of the researchers. The internal excitation caused by the variation in tooth mesh stiffness is a key factor in causing vibration. Therefore to reduce gear noise and vibrations several techniques have been proposed in recent years. In this research the experimental work is carried out to study the effect of planet phasing on noise and subsequent resulting vibrations of Nylon-6 planetary gear drive. For this purpose experimental set-up was built and trials were conducted for two different arrangements (i.e., with phasing and without phasing and it is observed that the noise level and resulting vibrations were reduced by planet phasing arrangement. So from the experimental results it is observed that by applying the meshing phase difference one can reduce planetary gear set noise and vibrations.

49 CFR 230.77 - Foundation brake gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Foundation brake gear. 230.77 Section 230.77... Tenders Brake and Signal Equipment § 230.77 Foundation brake gear. (a) Maintenance. Foundation brake gear...) Distance above the rails. No part of the foundation brake gear of the steam locomotive or tender shall be...

Characteristics of Reduction Gear in Electric Agricultural Vehicle

Science.gov (United States)

Choi, W. S.; Pratama, P. S.; Supeno, D.; Jeong, S. W.; Byun, J. Y.; Woo, J. H.; Lee, E. S.; Park, C. S.

2018-03-01

In electric agricultural machine a reduction gear is needed to convert the high speed rotation motion generated by DC motor to lower speed rotation motion used by the vehicle. The reduction gear consists of several spur gears. Spur gears are the most easily visualized gears that transmit motion between two parallel shafts and easy to produce. The modelling and simulation of spur gears in DC motor reduction gear is important to predict the actual motion behaviour. A pair of spur gear tooth in action is generally subjected to two types of cyclic stress: contact stress and bending stress. The stress may not attain their maximum values at the same point of contact fatigue. These types of failure can be minimized by analysis of the problem during the design stage and creating proper tooth surface profile with proper manufacturing methods. To improve its life expectation in this study modal and stress analysis of reduction gear is simulated using ANSYS workbench based on finite element method (FEM). The modal analysis was done to understand reduction gear deformation behaviour when vibration occurs. FEM static stress analysis is also simulated on reduction gear to simulate the gear teeth bending stress and contact stress behaviour.

Application of Face-Gear Drives in Helicopter Transmissions

Science.gov (United States)

Litvin, F. L.; Wang, J.-C.; Bossler, R. B., Jr.; Chen, Y.-J. D.; Heath, G.; Lewicki, D. G.

1992-01-01

The use of face gears in helicopter transmissions was explored. A light-weight, split torque transmission design utilizing face gears was described. Face-gear design and geometry were investigated. Topics included tooth generation, limiting inner and outer radii, tooth contact analysis, contact ratio, gear eccentricity, and structural stiffness. Design charts were developed to determine minimum and maximum face-gear inner and outer radii. Analytical study of transmission error showed face-gear drives were relatively insensitive to gear misalignment, but tooth contact was affected by misalignment. A method of localizing bearing contact to compensate for misalignment was explored. The proper choice of shaft support stiffness enabled good load sharing in the split torque transmission design. Face-gear experimental studies were also included and the feasibility of face gears in high-speed, high-load applications such as helicopter transmissions was demonstrated.

Gear failure of a PHWR refuelling machine

International Nuclear Information System (INIS)

Iorio, A.F.; Crespi, J.C.

1986-01-01

After ten year service in Atucha Nuclear Station a gear belonging to a pressurized heavy water reactor refuelling machine, failed. The gear box was used to transmit motion to the inlet-outlet heavy-water valve of that machine. Visual examination of the gear device revealed an absence of lubricant and several gear teeth were broken off at the root. The gear motion was transmitted from a speed-reducing device with controlled adjustable times in order to produce a right fitness of the valve closure. The main cause of gear failure was due to misalignment produced during assembly or in-service operation. It is suggested to control periodically the level of oil lubricant. (orig./IHOE) [de

Drawing cure: children's drawings as a psychoanalytic instrument.

Science.gov (United States)

Wittmann, Barbara

2010-01-01

This essay deals with the special case of drawings as psychoanalytical instruments. It aims at a theoretical understanding of the specific contribution made by children's drawings as a medium of the psychical. In the influential play technique developed by Melanie Klein, drawing continuously interacts with other symptomatic (play) actions. Nonetheless, specific functions of drawing within the play technique can be identified. The essay will discuss four crucial aspects in-depth: 1) the strengthening of the analysis's recursivity associated with the graphic artifact; 2) the opening of the analytic process facilitated by drawing; 3) the creation of a genuinely graphic mode of producing meaning that allows the child to develop a "theory" of the workings of his own psychic apparatus; and 4) the new possibilities of symbolization associated with the latter. In contrast to classical definitions of the psychological instrument, the child's drawing is a weakly structured tool that does not serve to reproduce psychic processes in an artificial, controlled setting. The introduction of drawing into the psychoanalytic cure is by no means interested in replaying past events, but in producing events suited to effecting a transformation of the synchronic structures of the unconscious.

Executive control of stimulus-driven and goal-directed attention in visual working memory.

Science.gov (United States)

Hu, Yanmei; Allen, Richard J; Baddeley, Alan D; Hitch, Graham J

2016-10-01

We examined the role of executive control in stimulus-driven and goal-directed attention in visual working memory using probed recall of a series of objects, a task that allows study of the dynamics of storage through analysis of serial position data. Experiment 1 examined whether executive control underlies goal-directed prioritization of certain items within the sequence. Instructing participants to prioritize either the first or final item resulted in improved recall for these items, and an increase in concurrent task difficulty reduced or abolished these gains, consistent with their dependence on executive control. Experiment 2 examined whether executive control is also involved in the disruption caused by a post-series visual distractor (suffix). A demanding concurrent task disrupted memory for all items except the most recent, whereas a suffix disrupted only the most recent items. There was no interaction when concurrent load and suffix were combined, suggesting that deploying selective attention to ignore the distractor did not draw upon executive resources. A final experiment replicated the independent interfering effects of suffix and concurrent load while ruling out possible artifacts. We discuss the results in terms of a domain-general episodic buffer in which information is retained in a transient, limited capacity privileged state, influenced by both stimulus-driven and goal-directed processes. The privileged state contains the most recent environmental input together with goal-relevant representations being actively maintained using executive resources.

14 CFR 25.1515 - Landing gear speeds.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Landing gear speeds. 25.1515 Section 25... Limitations § 25.1515 Landing gear speeds. (a) The established landing gear operating speed or speeds, V LO, may not exceed the speed at which it is safe both to extend and to retract the landing gear, as...

External gear pumps operating with non-Newtonian fluids: Modelling and experimental validation

Science.gov (United States)

Rituraj, Fnu; Vacca, Andrea

2018-06-01

External Gear Pumps are used in various industries to pump non-Newtonian viscoelastic fluids like plastics, paints, inks, etc. For both design and analysis purposes, it is often a matter of interest to understand the features of the displacing action realized by meshing of the gears and the description of the behavior of the leakages for this kind of pumps. However, very limited work can be found in literature about methodologies suitable to model such phenomena. This article describes the technique of modelling external gear pumps that operate with non-Newtonian fluids. In particular, it explains how the displacing action of the unit can be modelled using a lumped parameter approach which involves dividing fluid domain into several control volumes and internal flow connections. This work is built upon the HYGESim simulation tool, conceived by the authors' research team in the last decade, which is for the first time extended for the simulation of non-Newtonian fluids. The article also describes several comparisons between simulation results and experimental data obtained from numerous experiments performed for validation of the presented methodology. Finally, operation of external gear pump with fluids having different viscosity characteristics is discussed.

The impact of various distance between axes of worm gear on torque value. Worm gear test stand

Science.gov (United States)

Sobek, M.; Baier, A.; Grabowski, Ł.

2017-08-01

Transferring both rotational and translational movements in systems used in the automotive industry is a very important and complex issue. In addition, the situation becomes much more difficult and complicated when the design of the transition system requires a high precision of operation as well as a well definite and long operating life. Such requirements are imposed on all components of today’s motor vehicles. However, particular attention is paid to the elements that directly or indirectly affect the safety of persons traveling in the vehicle. Such components are undoubtedly components included as parts of the steering system of the vehicle. Power steering systems have been present in motor vehicles for more than a century. They go through continuous metamorphosis and they are getting better and better. Current power steering systems are based on an electric motor and some kind of transmission. Depending on the position of the drive relative to the steering column, different configurations of the transmission are used. This article will cover issues related to tests of power steering gearing using a worm drive. The worm drive is a very specific example of a propulsion system that uses twisted axles. Normally, in this type of transition you can find two gear units with the axis mounted with a 90° angle between. The components of the worm drive are a worm and a worm gear, also called a worm wheel. In terms of the geometrical form, the worm resembles a helical spur gear. The shape of the worm is similar to the shape of a screw with a trapezoidal thread. A correct matching of these two components ensures proper operation of the entire transmission. Incorrect positioning of the components in relation to each other can significantly reduce the lifetime of the drive unit, and also lead to abnormal work, eg by raising the noise level. This article describes a test method of finding the appropriate distance between the axles of both worm drive units by testing the

Lubrication and cooling for high speed gears

Science.gov (United States)

Townsend, D. P.

1985-01-01

The problems and failures occurring with the operation of high speed gears are discussed. The gearing losses associated with high speed gearing such as tooth mesh friction, bearing friction, churning, and windage are discussed with various ways shown to help reduce these losses and thereby improve efficiency. Several different methods of oil jet lubrication for high speed gearing are given such as into mesh, out of mesh, and radial jet lubrication. The experiments and analytical results for the various methods of oil jet lubrication are shown with the strengths and weaknesses of each method discussed. The analytical and experimental results of gear lubrication and cooling at various test conditions are presented. These results show the very definite need of improved methods of gear cooling at high speed and high load conditions.

Dynamics of High-Speed Precision Geared Rotor Systems

Directory of Open Access Journals (Sweden)

Lim Teik C.

2014-07-01

Full Text Available Gears are one of the most widely applied precision machine elements in power transmission systems employed in automotive, aerospace, marine, rail and industrial applications because of their reliability, precision, efficiency and versatility. Fundamentally, gears provide a very practical mechanism to transmit motion and mechanical power between two rotating shafts. However, their performance and accuracy are often hampered by tooth failure, vibrations and whine noise. This is most acute in high-speed, high power density geared rotor systems, which is the primary scope of this paper. The present study focuses on the development of a gear pair mathematical model for use to analyze the dynamics of power transmission systems. The theory includes the gear mesh representation derived from results of the quasi-static tooth contact analysis. This proposed gear mesh theory comprising of transmission error, mesh point, mesh stiffness and line-of-action nonlinear, time-varying parameters can be easily incorporated into a variety of transmission system models ranging from the lumped parameter type to detailed finite element representation. The gear dynamic analysis performed led to the discovery of the out-of-phase gear pair torsion modes that are responsible for much of the mechanical problems seen in gearing applications. The paper concludes with a discussion on effectual design approaches to minimize the influence of gear dynamics and to mitigate gear failure in practical power transmission systems.

Computer simulation of gear tooth manufacturing processes

Science.gov (United States)

Mavriplis, Dimitri; Huston, Ronald L.

1990-01-01

The use of computer graphics to simulate gear tooth manufacturing procedures is discussed. An analytical basis for the simulation is established for spur gears. The simulation itself, however, is developed not only for spur gears, but for straight bevel gears as well. The applications of the developed procedure extend from the development of finite element models of heretofore intractable geometrical forms, to exploring the fabrication of nonstandard tooth forms.

Asymptotic work distributions in driven bistable systems

International Nuclear Information System (INIS)

Nickelsen, D; Engel, A

2012-01-01

The asymptotic tails of the probability distributions of thermodynamic quantities convey important information about the physics of nanoscopic systems driven out of equilibrium. We apply a recently proposed method to analytically determine the asymptotics of work distributions in Langevin systems to an one-dimensional model of single-molecule force spectroscopy. The results are in excellent agreement with numerical simulations, even in the centre of the distributions. We compare our findings with a recent proposal for an universal form of the asymptotics of work distributions in single-molecule experiments.

Test gear and measurements a collection of useful and tested circuit design ideas'

CERN Document Server

Stewart OBE DLitthc, David

2013-01-01

This book provides a clear introduction to test gear in the field of electronics. As well as being a first guide to test gear and its use, the book includes much practical information and reference material for the more experienced electronics enthusiast or student.Based on a collection of feature articles originally published in Electronics - the Maplin Magazine, this work by Danny Stewart is sure to be useful to electronics constructors, students and experimenters alike. Details of all the common (and some not-so-common) items of test gear are included, alongside information regarding its us

Communication: Molecular gears

Energy Technology Data Exchange (ETDEWEB)

Burnell, E. Elliott, E-mail: elliott.burnell@ubc.ca [Chemistry Department, University of British Columbia, 2036 Main Mall, Vancouver, British Columbia V6T 1Z1 (Canada); Lange, Cornelis A. de, E-mail: c.a.de.lange@vu.nl [Atomic, Molecular and Laser Physics, Vrije Universiteit, De Boelelaan 1081, 1081 HV Amsterdam (Netherlands); Meerts, W. Leo, E-mail: leo.meerts@science.ru.nl [Atomic, Molecular and Laser Physics, Vrije Universiteit, De Boelelaan 1081, 1081 HV Amsterdam (Netherlands); Institute for Molecules and Materials, Radboud University Nijmegen, Heyendaalseweg 135, NL-6525 AJ Nijmegen (Netherlands)

2016-09-07

The {sup 1}H nuclear magnetic resonance spectrum of hexamethylbenzene orientationally ordered in the nematic liquid crystal ZLI-1132 is analysed using covariance matrix adaptation evolution strategy. The spectrum contains over 350 000 lines with many overlapping transitions, from which four independent direct dipolar couplings are obtained. The rotations of the six methyl groups appear to be correlated due to mutual steric hindrance. Adjacent methyl groups show counter-rotating or geared motion. Hexamethylbenzene thus behaves as a molecular hexagonal gear.

Determination on Damage Mechanism of the Planet Gear of Heavy Vehicle Final Drive

Science.gov (United States)

Ramdan, RD; Setiawan, R.; Sasmita, F.; Suratman, R.; Taufiqulloh

2018-02-01

The works focus on the investigation of damage mechanism of fractured in the form of spalling of the planet gears from the final drive assembly of 160-ton heavy vehicles. The objective of this work is to clearly understand the mechanism of damage. The work is the first stage of the on-going research on the remaining life estimation of such gears. The understanding of the damage mechanism is critical in order to provide accurate estimate of the gear’s remaining life with observed initial damage. The analysis was performed based on the metallurgy laboratory works, including visual observation, macro-micro fractography by optical stereo and optical microscope and micro-vickers hardness test. From visual observation it was observed pitting that form lining defect at common position, which is at gear flank position. From spalling sample it was observed ratchet mark at the boundary between macro pitting and the edge of fractured parts. Further observation on the cross-section of the samples by optical microscope confirm that initial micro pitting occur without spalling of the case hardened surface. Spalling occur when pitting achieve certain critical size, and occur at multiple initiation site of crack propagation. From the present research it was concluded that pitting was resulted due to repeated contact fatigue. In addition, development of micro to macro pitting as well as spalling occur at certain direction towards the top of the gear teeth.

Theory and practice of gearing and transmissions in honor of Professor Faydor L. Litvin

CERN Document Server

Barmina, Natalya

2016-01-01

This book brings together papers from all spheres of mechanical engineering related to gears and transmissions, from fundamentals to advanced applications, from academic results in numerical and experimental research, to new approaches to gear design and aspects of their optimization synthesis, and to the latest developments in manufacturing. Furthermore, this volume honours the work of Faydor L. Litvin on the 100th anniversary of this birth. He is acknowledged as the founder of the modern theory of gearing. An exhaustive list of his contributions and achievements and a biography are included.

Development in Geared Turbofan Aeroengine

Science.gov (United States)

Mohd Tobi, A. L.; Ismail, A. E.

2016-05-01

This paper looks into the implementation of epicyclic gear system to the aeroengine in order to increase the efficiency of the engine. The improvement made is in the direction of improving fuel consumption, reduction in pollutant gasses and perceived noise. Introduction of epicyclic gear system is capable to achieve bypass ratio of up to 15:1 with the benefits of weight and noise reduction. Radical new aircraft designs and engine installation are being studied to overcome some of the challenges associated with the future geared turbofan and open-rotor engine.

Fishing gear-related injury in California marine wildlife.

Science.gov (United States)

Dau, Brynie Kaplan; Gilardi, Kirsten V K; Gulland, Frances M; Higgins, Ali; Holcomb, Jay B; Leger, Judy St; Ziccardi, Michael H

2009-04-01

We reviewed medical records from select wildlife rehabilitation facilities in California to determine the prevalence of injury in California Brown Pelicans (Pelecanus occidentalis), gulls (Larus spp.), and pinniped species (Zalophus californianus, Mirounga angustirostris, and Phoca vitulina) due to fishing gear entanglement and ingestion from 2001 to 2006. Of 9,668 Brown Pelican, gull, and pinniped cases described during the 6-yr study period (2001-06), 1,090 (11.3%) were fishing gear-related. Pelican injuries caused by fishing gear were most common in the Monterey Bay region, where 59.6% of the pelicans rescued in this area and admitted to a rehabilitation center were injured by fishing gear over the 6-yr period. The highest prevalence of fishing gear-related injury in gulls was documented in the Los Angeles/Orange County region (16.1%), whereas the highest prevalences in pinnipeds were seen in the San Diego region (3.7%). Despite these higher prevalences of gull and pinniped fishing gear-related injuries in these specific regions, there was no statistical significance in these trends. Juvenile gulls and pinnipeds were more commonly injured by fishing gear than adults (gulls: P = 0.03, odds ratio = 1.29; pinnipeds: P = 0.01, odds ratio = 2.07). Male pinnipeds were twice as likely to be injured by fishing gear as females (P gear-related injury cases that were successfully rehabilitated and released (percentage of cases successfully rehabilitated to the point of release out of the total number of fishing gear-related injury cases) was high in all three species groups (pelicans: 63%; gulls: 54%; pinnipeds: 70%). Fishing gear-related injuries in Brown Pelicans and gulls were highest in the fall, but there was only a significant difference between seasons for fishing gear-related injuries in pelicans. Fishing gear-related injuries in pinnipeds most commonly occurred in summer; however, a statistical difference was not detected between seasons for pinnipeds. Derelict

50 CFR 654.25 - Prevention of gear conflicts.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Prevention of gear conflicts. 654.25... Measures § 654.25 Prevention of gear conflicts. (a) No person may knowingly place in the management area any article, including fishing gear, that interferes with fishing or obstructs or damages fishing gear...

29 CFR 1919.31 - Proof tests-loose gear.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Proof tests-loose gear. 1919.31 Section 1919.31 Labor... (CONTINUED) GEAR CERTIFICATION Certification of Vessels: Tests and Proof Loads; Heat Treatment; Competent Persons § 1919.31 Proof tests—loose gear. (a) Chains, rings, shackles and other loose gear (whether...

On the Correlation of Specific Film Thickness and Gear Pitting Life

Science.gov (United States)

Krantz, Timothy L.

2015-01-01

The effect of the lubrication regime on gear performance has been recognized, qualitatively, for decades. Often the lubrication regime is characterized by the specific film thickness defined as the ratio of lubricant film thickness to the composite surface roughness. It can be difficult to combine results of studies to create a cohesive and comprehensive dataset. In this work gear surface fatigue lives for a wide range of specific film values were studied using tests done with common rigs, speeds, lubricant temperatures, and test procedures. This study includes previously reported data, results of an additional 50 tests, and detailed information from lab notes and tested gears. The dataset comprised 258 tests covering specific film values (0.47 to 5.2). The experimentally determined surface fatigue lives, quantified as 10-percent life estimates, ranged from 8.7 to 86.8 million cycles. The trend is one of increasing life for increasing specific film. The trend is nonlinear. The observed trends were found to be in good agreement with data and recommended practice for gears and bearings. The results obtained will perhaps allow for the specific film parameter to be used with more confidence and precision to assess gear surface fatigue for purpose of design, rating, and technology development.

Face Gear Technology for Aerospace Power Transmission Progresses

Science.gov (United States)

2005-01-01

The use of face gears in an advanced rotorcraft transmission design was first proposed by the McDonnell Douglas Helicopter Company during their contracted effort with the U.S. Army under the Advanced Rotorcraft Transmission (ART) program. Face gears would be used to turn the corner between the horizontal gas turbine engine and the vertical output rotor shaft--a function currently done by spiral bevel gears. This novel gearing arrangement would substantially lower the drive system weight partly because a face gear mesh would be used to split the input power between two output gears. However, the use of face gears and their ability to operate successfully at the speeds and loads required for an aerospace environment was unknown. Therefore a proof-of-concept phase with an existing test stand at the NASA Lewis Research Center was pursued. Hardware was designed that could be tested in Lewis' Spiral Bevel Gear Test Rig. The initial testing indicated that the face gear mesh was a feasible design that could be used at high speeds and load. Surface pitting fatigue was the typical failure mode, and that could lead to tooth fracture. An interim project was conducted to see if slight modifications to the gear tooth geometry or an alternative heat treating process could overcome the surface fatigue problems. From the initial and interim tests, it was apparent that for the surface fatigue problems to be overcome the manufacturing process used for this component would have to be developed to the level used for spiral bevel gears. The current state of the art for face gear manufacturing required using less than optimal gear materials and manufacturing techniques because the surface of the tooth form does not receive final finishing after heat treatment as it does for spiral bevel gears. This resulted in less than desirable surface hardness and manufacturing tolerances. An Advanced Research and Projects Agency (ARPA) Technology Reinvestment Project has been funded to investigate

Contact Stress Analysis for Gears of Different Helix Angle Using Finite Element Method

Directory of Open Access Journals (Sweden)

Patil Santosh

2014-07-01

Full Text Available The gear contact stress problem has been a great point of interest for many years, but still an extensive research is required to understand the various parameters affecting this stress. Among such parameters, helix angle is one which has played a crucial role in variation of contact stress. Numerous studies have been carried out on spur gear for contact stress variation. Hence, the present work is an attempt to study the contact stresses among the helical gear pairs, under static conditions, by using a 3D finite element method. The helical gear pairs on which the analysis is carried are 0, 5, 15, 25 degree helical gear sets. The Lagrange multiplier algorithm has been used between the contacting pairs to determine the stresses. The helical gear contact stress is evaluated using FE model and results have also been found at different coefficient of friction, varying from 0.0 to 0.3. The FE results have been further compared with the analytical calculations. The analytical calculations are based upon Hertz and AGMA equations, which are modified to include helix angle. The commercial finite element software was used in the study and it was shown that this approach can be applied to gear design efficiently. The contact stress results have shown a decreasing trend, with increase in helix angle.

50 CFR 622.46 - Prevention of gear conflicts.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Prevention of gear conflicts. 622.46... Management Measures § 622.46 Prevention of gear conflicts. (a) No person may knowingly place in the Gulf EEZ any article, including fishing gear, that interferes with fishing or obstructs or damages fishing gear...

Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain

Science.gov (United States)

2014-01-01

Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain by Kelsen E. LaBerge, Eric C. Ames, and Brian D. Dykas...5066 ARL-TR-6795 January 2014 Detection of Naturally Occurring Gear and Bearing Faults in a Helicopter Drivetrain Kelsen E. LaBerge...ELEMENT NUMBER 6. AUTHOR(S) Kelsen E. LaBerge, Eric C. Ames, and Brian D. Dykas 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER

Research on the Problem of Spur Gear Teeth Contact in the Car Gear Box

Directory of Open Access Journals (Sweden)

Viktor Skrickij

2011-04-01

Full Text Available The article presents research on the problem of two gear contact in the car gearbox. Contact stiffness is evaluated for the whole period of mesh. Also, contact stresses are evaluated in the contact place. The presented method can be used for calculating spur gear.Article in Lithuanian

50 CFR 622.31 - Prohibited gear and methods.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Prohibited gear and methods. 622.31... Management Measures § 622.31 Prohibited gear and methods. In addition to the prohibited gear/methods specified in this section, see §§ 622.33, 622.34, and 622.35 for seasonal/area prohibited gear/methods and...

50 CFR 640.22 - Gear and diving restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Gear and diving restrictions. 640.22... ATLANTIC Management Measures § 640.22 Gear and diving restrictions. (a) Prohibited gear and methods. (1) A spiny lobster may not be taken in the EEZ with a spear, hook, or similar device, or gear containing such...

Research of Planetary Gear Fault Diagnosis Based on Permutation Entropy of CEEMDAN and ANFIS

Directory of Open Access Journals (Sweden)

Moshen Kuai

2018-03-01

Full Text Available For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN Adaptive Neuro-fuzzy Inference System (ANFIS in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

Research of Planetary Gear Fault Diagnosis Based on Permutation Entropy of CEEMDAN and ANFIS.

Science.gov (United States)

Kuai, Moshen; Cheng, Gang; Pang, Yusong; Li, Yong

2018-03-05

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN) Adaptive Neuro-fuzzy Inference System (ANFIS) in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF) and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

Bifurcation phenomena in internal dynamics of gear systems

Directory of Open Access Journals (Sweden)

Hortel M.

2007-10-01

Full Text Available The impact effects in gear mesh represent specific phenomena in the dynamic investigation of highspeed light transmission systems with kinematic couplings. They are caused of greater dynamic than static elastic deformations in meshing gear profiles. In term of internal dynamics they are influenced among others by time heteronomous stiffness functions in gear mesh and resonance tuning of stiffness level. The damping in gear mesh and in gear system is concerned significantly in the amplitude progress, greatness and phase shift of relative motion towards stiffness function alternatively towards its modify form in gear mesh. In consequence of these and another actions rise above resonance characteristics certain singular locations with jump amplitude course.

On the Determination of the Gear Teeth Wear Using an Inductive Sensor

Directory of Open Access Journals (Sweden)

V. N. Atamanov

2015-01-01

Full Text Available A problem to measure the teeth wear of rotating gear wheels and a possibility to create simple, reliable and inexpensive mobile systems of diagnostics allowing to record the wear in the course of use are presently relevant. The paper presents implemented technical solutions as a result of work. The aim of the work was to prove experimentally that it is possible to measure the teeth wear of a gear wheel using a passive inductive sensor and a positioning disk. The technique to determine the wear uses a phase-chronometric method developed at BMSTU.To reach the objective, an experimental installation was designed and made. Works are performed, and experimental results of used stationary inductive sensors of passive type to measure the ferromagnetic gear wheels wear of reducers in use are received. The technique for defining the points at the output signal of the inductive sensor, which correspond to the specified points of the tooth profile and, in particular, to the profile points on a pitch circle of the tooth of gear wheel has been developed. Experiments allowed us to define the main dependences of signal parameters on the sizes and arrangement of the sensor magnet with respect to the passing tooth in the course of rotation, as well as on the number of the sensor coil turns, speed of gear wheel rotation, and on the gap size between the end face of the sensor and the top of a tooth.The technique for positioning the sensor with respect to tooth has been deve loped. In particular, it allows us to position a sensor at any point of the involute, including also a point of the profile on a pitch circle. This is necessary to adjust the sensor. The conducted researches allowed us to develop a technique for exact measuring system adjustment to a hitch circle of the gear wheel and to develop for this purpose a system of diagnostics and measurement of teeth wear with the wheel being rotated. The results of work performed at the JSC ELARA in Cheboksary city

New progressive technology of flat gears processing development

Directory of Open Access Journals (Sweden)

Михайло Володимирович Маргуліс

2015-11-01

Full Text Available Relevant scientific and technical problems in relation to mechanical engineering is development of new technological processes that make it possible to achieve high accuracy and durability of machine parts that meet the requirements imposed on them. So it is important to develop a new method to make a flat gear teeth by plastic deformation of the ingot. The article deals with the actual problem of improving productivity and quality of plane wheels teeth that are widely used in advanced wave, planetary and other transmissions. A progressive method to produce flat gear teeth gear by plastic deformation of the ingot with two knurl rollers alternately moving reciprocally in the direction not intersecting the axis of the ingot mounting surface has been described in the article. The working surface of the rollers corresponds to the resulting shape of the teeth. The schemes of the teeth installing and knurling have been shown. The necessary material and the heat treatment of the knurling tools have been described. Its use will significantly increase the wear resistance of the working surfaces of the teeth and their durability as well as to increase productivity and its manufacturing costs. The material of the rollers is BC15steel. The surface layer of the knurling tools was subjected to nitration, surface hardness being up to 65 HRC. Knurling is made in the5236P shaper suited for this purpose

Offset Compound Gear Inline Two-Speed Drive

Science.gov (United States)

Stevens, Mark A. (Inventor); Handschuh, Robert F. (Inventor); Lewicki, David G. (Inventor)

2014-01-01

A two-speed transmission having an input shaft and an output shaft, the transmission being capable of transitioning between fixed ratios, the high-range ratio being direct 1:1 and the low-range ratio being about 2:1. The transmission is a simple lightweight, yet robust, configuration utilizing only two gear meshes, being comprised of an input gear, a cluster gear, and an output gear. The transmission is controlled with a clutch and a sprag and with the input and output shafts turning in the same direction.

An energy management system for a directly-driven electric scooter

International Nuclear Information System (INIS)

Yang, Yee-Pien; Liu, Jieng-Jang; Hu, Tsung-Hsien

2011-01-01

An energy management system with an electronic gearshift and regenerative braking is presented to improve the gross efficiency and driving range of an electric scooter, driven directly by a four-phase axial-flux DC brushless wheel motor. The integration of stator windings, batteries, ultracapacitors, and a digital controller constitutes an energy management system, which features smooth electronic gear shifting and regenerative braking. The gross efficiency of the experimental scooter is improved in the drivable range by 20% with respect to that without regenerative braking. The battery-to-wheel efficiency was also above 70% for both low- and high-speed gears.

An energy management system for a directly-driven electric scooter

Energy Technology Data Exchange (ETDEWEB)

Yang, Yee-Pien, E-mail: ypyang@ntu.edu.t [Department of Mechanical Engineering, National Taiwan University, No. 1, Roosevelt Road, Section 4, Taipei, Taiwan (China); Liu, Jieng-Jang, E-mail: jjliu@ntu.edu.t [Department of Mechanical Engineering, National Taiwan University, No. 1, Roosevelt Road, Section 4, Taipei, Taiwan (China); Hu, Tsung-Hsien, E-mail: elvishu@artc.org.t [Department of Mechanical Engineering, National Taiwan University, No. 1, Roosevelt Road, Section 4, Taipei, Taiwan (China)

2011-01-15

An energy management system with an electronic gearshift and regenerative braking is presented to improve the gross efficiency and driving range of an electric scooter, driven directly by a four-phase axial-flux DC brushless wheel motor. The integration of stator windings, batteries, ultracapacitors, and a digital controller constitutes an energy management system, which features smooth electronic gear shifting and regenerative braking. The gross efficiency of the experimental scooter is improved in the drivable range by 20% with respect to that without regenerative braking. The battery-to-wheel efficiency was also above 70% for both low- and high-speed gears.

An energy management system for a directly-driven electric scooter

Energy Technology Data Exchange (ETDEWEB)

Yee-Pien Yang; Jieng-Jang Liu; Tsung-Hsien Hu [Department of Mechanical Engineering, National Taiwan University, No. 1, Roosevelt Road, Section 4, Taipei (China)

2011-01-15

An energy management system with an electronic gearshift and regenerative braking is presented to improve the gross efficiency and driving range of an electric scooter, driven directly by a four-phase axial-flux DC brushless wheel motor. The integration of stator windings, batteries, ultracapacitors, and a digital controller constitutes an energy management system, which features smooth electronic gear shifting and regenerative braking. The gross efficiency of the experimental scooter is improved in the drivable range by 20% with respect to that without regenerative braking. The battery-to-wheel efficiency was also above 70% for both low- and high-speed gears. (author)

Design aspects of harmonic drive gear and performance improvement of its by problems identification: A review

Science.gov (United States)

Routh, Bikash

2018-04-01

The present paper aims at review on different aspects of harmonic drive gear to identify literature gap for future research. The present article is started first making the comparative study of harmonic drive gear over conventional gear, highlighting its historical background, its application, limitation etc. and then describing working principle of each and every components of it with detail dimensioning and modelling. The present article is further extended to study the different design aspects i.e. synthesis of tooth profiles, lubrication, stress, strain, torque, load sharing, kinematics error and vibration in details etc., identifying problems and then suggesting future perspective for the performance improvement of harmonic drive gear.

Simulation of Dynamic Behavior of the Flexible Wheel of the Double Harmonic Gear Transmission

Directory of Open Access Journals (Sweden)

Draghiţa Ianici

2014-06-01

Full Text Available The paper presents the construction and functioning of a new type the harmonic gear transmission named double harmonic gear transmission, which can be used in the construction drives of industrial robots. In the second part of this paper is presented the dynamic analysis of the double harmonic gear transmission, which is based on the results of the numerical simulations of the flexible wheel in case of its deformation with a mechanical wave generator with disc cam. Investigation of dynamic behavior of the flexible toothed wheel was performed by using the finite element method in SolidWorks Simulation software.

46 CFR 61.20-1 - Steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Steering gear. 61.20-1 Section 61.20-1 Shipping COAST... Periodic Tests of Machinery and Equipment § 61.20-1 Steering gear. (a) The marine inspector must inspect the steering gear at each inspection for certification for vessels whose Certificate of Inspections...

Diagnostics of power transmissions system with tooth gear

Directory of Open Access Journals (Sweden)

Grzegorz WOJNAR

2008-01-01

Full Text Available This paper presents results of laboratory tests that were aimed at detecting early stages of various faults in toothed wheels by measurement and analysis of transverse vibration speed of the transmission gear shafts. In experimental investigation, cracking of the root tooth and chipping of the tooth were detected. The laser vibrometer Ometron VH300+ was used for non-contact measurement of shaft transversal vibration speed. Gear vibrations were recorded in selected points of gear housing and gear shafts at different speeds and gear loads. Results were analyzed and compared but in this paper is presented only selected examples. This paper shows that on the basis of the transverse vibration speed of transmission gear shafts, it is possible to detect defects at an earlier stage than on the basis of the housing vibration accelerations. In the case of measuring gear shaft vibration velocity, the way of the signal generated by the defect of a gear wheel (or bearing is shortened as well as the influence of composed transmittance of the bearing-gear housing system is eliminated. WV time-frequency analysis and complex continuous wavelet transformations were used for detection. The authors introduced a measure of local tooth damage, which was proportional to the size of damage. The results of research presented in this paperconfirmed that the defect's measure is very sensitive to the development of teeth faults.

A Computational Investigation of Gear Windage

Science.gov (United States)

Hill, Matthew J.; Kunz, Robert F.

2012-01-01

A CFD method has been developed for application to gear windage aerodynamics. The goals of this research are to develop and validate numerical and modeling approaches for these systems, to develop physical understanding of the aerodynamics of gear windage loss, including the physics of loss mitigation strategies, and to propose and evaluate new approaches for minimizing loss. Absolute and relative frame CFD simulation, overset gridding, multiphase flow analysis, and sub-layer resolved turbulence modeling were brought to bear in achieving these goals. Several spur gear geometries were studied for which experimental data are available. Various shrouding configurations and free-spinning (no shroud) cases were studied. Comparisons are made with experimental data from the open literature, and data recently obtained in the NASA Glenn Research Center Gear Windage Test Facility. The results show good agreement with experiment. Interrogation of the validative and exploratory CFD results have led, for the first time, to a detailed understanding of the physical mechanisms of gear windage loss, and have led to newly proposed mitigation strategies whose effectiveness is computationally explored.

Evaluation Of Vibration-Monitoring Gear-Diagnostic System

Science.gov (United States)

Townsend, Dennis P.; Zakrajsek, James J.

1995-01-01

Report describes experimental evaluation of commercial electronic system designed to monitor vibration signal from accelerometer on gear-box to detect vibrations indicative of damage to gears. System includes signal-conditioning subsystem and personal computer in which analog-to-digital converter installed. Results show system fairly effective in detecting surface fatigue pits on spur-gear teeth.

46 CFR 182.610 - Main steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Main steering gear. 182.610 Section 182.610 Shipping...) MACHINERY INSTALLATION Steering Systems § 182.610 Main steering gear. (a) A vessel must be provided with a main steering gear that is: (1) Of adequate strength and capable of steering the vessel at all service...

Involute Spur Gear Template Development by Parametric Technique ...

African Journals Online (AJOL)

Nekky Umera

cylindrical coordinate systems to create the involute curve profile. Since spur gear ... Template gear development using parametric method means that the dimensions control the ... and rapid prototyping of interlocking gears. Excel is a common ...

New generation methods for spur, helical, and spiral-bevel gears

Science.gov (United States)

Litvin, F. L.; Tsung, W.-J.; Coy, J. J.; Handschuh, R. F.; Tsay, C.-B. P.

1987-01-01

New methods for generating spur, helical, and spiral-bevel gears are proposed. These methods provide the gears with conjugate gear tooth surfaces, localized bearing contact, and reduced sensitivity to gear misalignment. Computer programs have been developed for simulating gear meshing and bearing contact.

Adaptive landing gear concept—feedback control validation

Science.gov (United States)

Mikulowski, Grzegorz M.; Holnicki-Szulc, Jan

2007-12-01

The objective of this paper is to present an integrated feedback control concept for adaptive landing gears (ALG) and its experimental validation. Aeroplanes are subjected to high dynamic loads as a result of the impact during each landing. Classical landing gears, which are in common use, are designed in accordance with official regulations in a way that ensures the optimal energy dissipation for the critical (maximum) sink speed. The regulations were formulated in order to ensure the functional capability of the landing gears during an emergency landing. However, the landing gears, whose characteristics are optimized for these critical conditions, do not perform well under normal impact conditions. For that situation it is reasonable to introduce a system that would adapt the characteristics of the landing gears according to the sink speed of landing. The considered system assumes adaptation of the damping force generated by the landing gear, which would perform optimally in an emergency situation and would adapt itself for regular landings as well. This research covers the formulation and design of the control algorithms for an adaptive landing gear based on MR fluid, implementation of the algorithms on an FPGA platform and experimental verification on a lab-scale landing gear device. The main challenge of the research was to develop a control methodology that could operate effectively within 50 ms, which is assumed to be the total duration of the phenomenon. The control algorithm proposed in this research was able to control the energy dissipation process on the experimental stand.

High Speed Gear Sized and Configured to Reduce Windage Loss

Science.gov (United States)

Kunz, Robert F. (Inventor); Medvitz, Richard B. (Inventor); Hill, Matthew John (Inventor)

2013-01-01

A gear and drive system utilizing the gear include teeth. Each of the teeth has a first side and a second side opposite the first side that extends from a body of the gear. For each tooth of the gear, a first extended portion is attached to the first side of the tooth to divert flow of fluid adjacent to the body of the gear to reduce windage losses that occur when the gear rotates. The gear may be utilized in drive systems that may have high rotational speeds, such as speeds where the tip velocities are greater than or equal to about 68 m/s. Some embodiments of the gear may also utilize teeth that also have second extended portions attached to the second sides of the teeth to divert flow of fluid adjacent to the body of the gear to reduce windage losses that occur when the gear rotates.

VARIABLE MESH STIFFNESS OF SPUR GEAR TEETH USING ...

African Journals Online (AJOL)

gear engagement. A gear mesh kinematic simulation ... model is appropnate for VMS of a spur gear tooth. The assumptions for ... This process has been continued until one complete tooth meshing cycle is ..... Element Method. Using MATLAB,.

Određivanje krutosti planetarnog prenosnika / Determination of gear mesh stiffness in planetary gearing

Directory of Open Access Journals (Sweden)

Vojislav Batinić

2008-04-01

Full Text Available Kontaktna krutost zubaca jedan je od glavnih generatora unutrašnjih dinamičkih sila u spregama zupčanika planetarnih prenosnika. Neophodan je pri opisivanju dinamičkog ponašanja planetarnih prenosnika, tj. pri postavljanju jednačina dinamičke ravnoteže. U radu je prikazan metodološki pristup analitičkom i eksperimentalnom određivanju krutosti posmatranog planetarnog prenosnika. / Gear mesh stiffness in planetary gearing is one of the main generators of internal dynamic forces. It is necessary in describing dynamic behavior of planetary trains, i.e. in defining their equations of dynamic balance. This paper presents a methodological approach to experimental and analytical calculation of stiffness in planetary gearing.

Hybrid Gear Performance Under Loss-of-Lubrication Conditions

Science.gov (United States)

Laberge, Kelsen E.; Berkebile, Stephen P.; Handschuh, Robert F.; Roberts, Gary D.

2017-01-01

Hybrid composite gear technology is being investigated to increase power density in rotorcraft drive systems. These gears differ from conventional steel gears in that the structural web material is replaced with a lightweight carbon fiber composite. Past studies have focused on performance of this technology under normal operating conditions, however, for this technology to be viable it must also withstand adverse conditions. The study presented here evaluates the performance of hybrid gears under loss-of-lubrication conditions in NASA Glenn Research Centers Contact Fatigue Test Facility. Two experiments are presented using small-scale 3.5 inch (8.9 cm) pitch diameter hybrid gears and compared to a baseline steel gear pair. Results of these tests show that there are limitations to the use of a hexagonal interlock pattern between the steel and composite. There is also evidence that the presence of polymer in the gear during an oil out event has a potential to increase time to failure. Further studies are planned to expand on these initial findings.

Prediction of potential failures in hydraulic gear pumps

Directory of Open Access Journals (Sweden)

E. Lisowski

2010-07-01

Full Text Available Hydraulic gear pumps are used in many machines and devices. In hydraulic systems of machines gear pumps are main component ofsupply unit or perform auxiliary function. Gear pumps opposite to vane pumps are less complicated. They consists of such components as:housing, gear wheels, bearings, shaft, seal for rotation motion which are not very sensitive for damage and that is why they are using veryoften. However, gear pumps are break down from time to time. Usually damage of pump cause shutting down of machines and devices.One of the way for identifying potential failures and foreseeing their effects is a quality method. On the basis of these methods apreventing action might be undertaken before failure appear. In this paper potential failures and damages of a gear pump were presented bythe usage of matrix FMEA analysis.

Economic method for helical gear flank surface characterisation

Science.gov (United States)

Koulin, G.; Reavie, T.; Frazer, R. C.; Shaw, B. A.

2018-03-01

Typically the quality of a gear pair is assessed based on simplified geometric tolerances which do not always correlate with functional performance. In order to identify and quantify functional performance based parameters, further development of the gear measurement approach is required. Methodology for interpolation of the full active helical gear flank surface, from sparse line measurements, is presented. The method seeks to identify the minimum number of line measurements required to sufficiently characterise an active gear flank. In the form ground gear example presented, a single helix and three profile line measurements was considered to be acceptable. The resulting surfaces can be used to simulate the meshing engagement of a gear pair and therefore provide insight into functional performance based parameters. Therefore the assessment of the quality can be based on the predicted performance in the context of an application.

Advanced Gear Alloys for Ultra High Strength Applications

Science.gov (United States)

Shen, Tony; Krantz, Timothy; Sebastian, Jason

2011-01-01

Single tooth bending fatigue (STBF) test data of UHS Ferrium C61 and C64 alloys are presented in comparison with historical test data of conventional gear steels (9310 and Pyrowear 53) with comparable statistical analysis methods. Pitting and scoring tests of C61 and C64 are works in progress. Boeing statistical analysis of STBF test data for the four gear steels (C61, C64, 9310 and Pyrowear 53) indicates that the UHS grades exhibit increases in fatigue strength in the low cycle fatigue (LCF) regime. In the high cycle fatigue (HCF) regime, the UHS steels exhibit better mean fatigue strength endurance limit behavior (particularly as compared to Pyrowear 53). However, due to considerable scatter in the UHS test data, the anticipated overall benefits of the UHS grades in bending fatigue have not been fully demonstrated. Based on all the test data and on Boeing s analysis, C61 has been selected by Boeing as the gear steel for the final ERDS demonstrator test gearboxes. In terms of potential follow-up work, detailed physics-based, micromechanical analysis and modeling of the fatigue data would allow for a better understanding of the causes of the experimental scatter, and of the transition from high-stress LCF (surface-dominated) to low-stress HCF (subsurface-dominated) fatigue failure. Additional STBF test data and failure analysis work, particularly in the HCF regime and around the endurance limit stress, could allow for better statistical confidence and could reduce the observed effects of experimental test scatter. Finally, the need for further optimization of the residual compressive stress profiles of the UHS steels (resulting from carburization and peening) is noted, particularly for the case of the higher hardness C64 material.

46 CFR 58.25-40 - Arrangement of the steering-gear compartment.

Science.gov (United States)

2010-10-01

..., separated from any machinery space; (2) Ensure working access to machinery and controls in the compartment; and (3) Include handrails and either gratings or other non-slip surfaces to ensure a safe working environment if hydraulic fluid leaks. Note: Where practicable, all steering gear should be located in the...

Gear Fault Diagnosis Based on BP Neural Network

Science.gov (United States)

Huang, Yongsheng; Huang, Ruoshi

2018-03-01

Gear transmission is more complex, widely used in machinery fields, which form of fault has some nonlinear characteristics. This paper uses BP neural network to train the gear of four typical failure modes, and achieves satisfactory results. Tested by using test data, test results have an agreement with the actual results. The results show that the BP neural network can effectively solve the complex state of gear fault in the gear fault diagnosis.

Vibration and Operational Characteristics of a Composite-Steel (Hybrid) Gear

Science.gov (United States)

Handschuh, Robert F.; LaBerge, Kelsen E.; DeLuca, Samuel; Pelagalli, Ryan

2014-01-01

Hybrid gears have been tested consisting of metallic gear teeth and shafting connected by composite web. Both free vibration and dynamic operation tests were completed at the NASA Glenn Spur Gear Fatigue Test Facility, comparing these hybrid gears to their steel counterparts. The free vibration tests indicated that the natural frequency of the hybrid gear was approximately 800 Hz lower than the steel test gear. The dynamic vibration tests were conducted at five different rotational speeds and three levels of torque in a four square test configuration. The hybrid gears were tested both as fabricated (machined, composite layup, then composite cure) and after regrinding the gear teeth to the required aerospace tolerance. The dynamic vibration tests indicated that the level of vibration for either type of gearing was sensitive to the level of load and rotational speed.

46 CFR 108.641 - Instructions for changing steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Instructions for changing steering gear. 108.641 Section... steering gear. Instructions stating, in order, the different steps to be taken for changing to emergency and secondary steering gear must be posted in the steering gear room and at each secondary steering...

Wear Characterization of Carbon Nanotubes Reinforced Acetal Spur, Helical, Bevel and Worm Gears Using a TS Universal Test Rig

Science.gov (United States)

Yousef, Samy; Osman, T. A.; Abdalla, Abdelrahman H.; Zohdy, Gamal A.

2015-12-01

Although the applications of nanotechnologies are increasing, there remains a significant barrier between nanotechnology and machine element applications. This work aims to remove this barrier by blending carbon nanotubes (CNT) with common types of acetal polymer gears (spur, helical, bevel and worm). This was done by using adhesive oil (paraffin) during injection molding to synthesize a flange and short bars containing 0.02% CNT by weight. The flanges and short bars were machined using hobbing and milling machines to produce nanocomposite polymer gears. Some defects that surfaced in previous work, such as the appearance of bubbles and unmelted pellets during the injection process, were avoided to produce an excellent dispersion of CNT in the acetal. The wear resistances of the gears were measured by using a TS universal test rig using constant parameters for all of the gears that were fabricated. The tests were run at a speed of 1420 rpm and a torque of 4 Nm. The results showed that the wear resistances of the CNT/acetal gears were increased due to the addition of CNT, especially the helical, bevel and worm gears.

Ultrasonic test of highly stressed gear shafts

Energy Technology Data Exchange (ETDEWEB)

Schreiner, T [Siemens AG, Power Generation, KWU, Muelheim (Germany); Heinrich, W [Siemens AG, Power Generation, KWU, Berlin (Germany); Achtzehn, J [Siemens AG, Power Generation, ICVW, Erlangen (Germany); Hensley, H [Siemens Power Generation (Germany)

1999-12-31

In the power plant industry, gears are used for increasingly higher turbine capacities. Efficiency enhancements, particularly for the combined gas and steam turbine process, lead to an increase in stresses, even for high-performance gears. Consequently, the requirements for non-destructive material testing are on the increase as well. At Siemens KWU, high-performance gears are used so far only for gas turbines with lower rating (65 MW) to adapt the gas turbine speed (5413 rpm) to the generator speed (3000 rpm/ 50 Hz or 3600 rpm/60 Hz). The gear train consists of a forged and case-hardened wheel shaft and pinion shaft made of material 17 CrNiMo 6, where the wheel shaft can be either a solid or a hollow shaft. Dimensions are typically 2.3 m length and 1 m diameter. As a rule, pinion shafts are solid. The gear design, calling for an additional torsion shaft turning inside the hollow wheel shaft, can absorb more torsional load surges and is more tolerant of deviations during gear train alignment. This design requires two additional forgings (torsion shaft and hub) and an additional bearing 2 refs.

Ultrasonic test of highly stressed gear shafts

Energy Technology Data Exchange (ETDEWEB)

Schreiner, T. [Siemens AG, Power Generation, KWU, Muelheim (Germany); Heinrich, W. [Siemens AG, Power Generation, KWU, Berlin (Germany); Achtzehn, J. [Siemens AG, Power Generation, ICVW, Erlangen (Germany); Hensley, H. [Siemens Power Generation (Germany)

1998-12-31

In the power plant industry, gears are used for increasingly higher turbine capacities. Efficiency enhancements, particularly for the combined gas and steam turbine process, lead to an increase in stresses, even for high-performance gears. Consequently, the requirements for non-destructive material testing are on the increase as well. At Siemens KWU, high-performance gears are used so far only for gas turbines with lower rating (65 MW) to adapt the gas turbine speed (5413 rpm) to the generator speed (3000 rpm/ 50 Hz or 3600 rpm/60 Hz). The gear train consists of a forged and case-hardened wheel shaft and pinion shaft made of material 17 CrNiMo 6, where the wheel shaft can be either a solid or a hollow shaft. Dimensions are typically 2.3 m length and 1 m diameter. As a rule, pinion shafts are solid. The gear design, calling for an additional torsion shaft turning inside the hollow wheel shaft, can absorb more torsional load surges and is more tolerant of deviations during gear train alignment. This design requires two additional forgings (torsion shaft and hub) and an additional bearing 2 refs.

A Circularly Arranged Sextuple Triptycene Gear Molecule.

Science.gov (United States)

Ube, Hitoshi; Yamada, Ryo; Ishida, Jun-Ichi; Sato, Hiroyasu; Shiro, Motoo; Shionoya, Mitsuhiko

2017-11-22

Herein we report the synthesis of a circularly arranged sextuple triptycene gear molecule, hexakis(10-dodecyloxy-9-triptycyl)ethynylbenzene, via the trimerization of the corresponding triyne with a cobalt catalyst. The six triptycene gears are closely engaged with each other as confirmed by single crystal X-ray structure analysis, and their motion in solution was established by NMR spectroscopy. Notably, when one bulky RuCp* complex was attached to one triptycene gear, the whole movement of the six gears was highly restricted via their mechanical engagement. Development of such a multigear molecule would provide a structural basis for molecular motion transmission systems with a switching function.

Linear dynamic coupling in geared rotor systems

Science.gov (United States)

David, J. W.; Mitchell, L. D.

1986-01-01

The effects of high frequency oscillations caused by the gear mesh, on components of a geared system that can be modeled as rigid discs are analyzed using linear dynamic coupling terms. The coupled, nonlinear equations of motion for a disc attached to a rotating shaft are presented. The results of a trial problem analysis show that the inclusion of the linear dynamic coupling terms can produce significant changes in the predicted response of geared rotor systems, and that the produced sideband responses are greater than the unbalanced response. The method is useful in designing gear drives for heavy-lift helicopters, industrial speed reducers, naval propulsion systems, and heavy off-road equipment.

Optimization of Recycled Glass Fibre-Reinforced Plastics Gear via Integration of the Taguchi Method and Grey Relational Analysis

Science.gov (United States)

Mizamzul Mehat, Nik; Syuhada Zakarria, Noor; Kamaruddin, Shahrul

2018-03-01

The increase in demand for industrial gears has resulted in the increase in usage of plastic-matrix composites particularly glass fibre-reinforced plastics as the gear materials. The usage of these synthetic fibers is to enhance the mechanical strength and the thermal resistance of the plastic gears. Nevertheless, the production of large quantities of these synthetic fibre-reinforced composites poses a serious threat to the ecosystem. Comprehending to this fact, the present work aimed at investigating the effects of incorporating recycled glass fibre-reinforced plastics in various compositions particularly on dimensional stability and mechanical properties of gear produced with diverse injection moulding processing parameters setting. The integration of Grey relational analysis (GRA) and Taguchi method was adopted to evaluate the influence of recycled glass fibre-reinforced plastics and variation in processing parameters on gear quality. From the experimental results, the blending ratio was found as the most influential parameter of 56.0% contribution in both improving tensile properties as well as in minimizing shrinkage, followed by mould temperature of 24.1% contribution and cooling time of 10.6% contribution. The results obtained from the aforementioned work are expected to contribute to accessing the feasibility of using recycled glass fibre-reinforced plastics especially for gear application.

Analytical and Numerical Tooth Contact Analysis (TCA of Standard and Modified Involute Profile Spur Gear

Directory of Open Access Journals (Sweden)

Nassear Rasheid Hmoad

2016-03-01

Full Text Available Among all the common mechanical transmission elements, gears still playing the most dominant role especially in the heavy duty works offering extraordinary performance under extreme conditions and that the cause behind the extensive researches concentrating on the enhancement of its durability to do its job as well as possible. Contact stress distribution within the teeth domain is considered as one of the most effective parameters characterizing gear life, performance, efficiency, and application so that it has been well sought for formal gear profiles and paid a lot of attention for moderate tooth shapes. The aim of this work is to investigate the effect of pressure angle, speed ratio, and correction factor on the maximum contact and bending stress value and principal stresses distribution for symmetric and asymmetric spur gear. The analytical investigation adopted Hertz equations to find the contact stress value, distribution, and the contact zone width while the numerical part depends on Ansys software version 15, as a FE solver with Lagrange and penalty contact algorithm. The most fruitful points to be noticed are that the increasing of pressure angle and speed ratio trends to minimize all the induced stresses for the classical gears and the altered teeth shape with larger loaded side pressure angle than the unloaded side one behave better than the symmetric teeth concerning the stress reduction.

Vibration Propagation of Gear Dynamics in a Gear-Bearing-Housing System Using Mathematical Modeling and Finite Element Analysis

Science.gov (United States)

Parker, Robert G.; Guo, Yi; Eritenel, Tugan; Ericson, Tristan M.

2012-01-01

Vibration and noise caused by gear dynamics at the meshing teeth propagate through power transmission components to the surrounding environment. This study is devoted to developing computational tools to investigate the vibro-acoustic propagation of gear dynamics through a gearbox using different bearings. Detailed finite element/contact mechanics and boundary element models of the gear/bearing/housing system are established to compute the system vibration and noise propagation. Both vibration and acoustic models are validated by experiments including the vibration modal testing and sound field measurements. The effectiveness of each bearing type to disrupt vibration propagation is speed-dependent. Housing plays an important role in noise radiation .It, however, has limited effects on gear dynamics. Bearings are critical components in drivetrains. Accurate modeling of rolling element bearings is essential to assess vibration and noise of drivetrain systems. This study also seeks to fully describe the vibro-acoustic propagation of gear dynamics through a power-transmission system using rolling element and fluid film wave bearings. Fluid film wave bearings, which have higher damping than rolling element bearings, could offer an energy dissipation mechanism that reduces the gearbox noise. The effectiveness of each bearing type to disrupt vibration propagation in explored using multi-body computational models. These models include gears, shafts, rolling element and fluid film wave bearings, and the housing. Radiated noise is mapped from the gearbox surface to surrounding environment. The effectiveness of rolling element and fluid film wave bearings in breaking the vibro-acoustic propagation path from the gear to the housing is investigated.

A Generalized Dynamic Model of Geared System: Establishment and Application

Directory of Open Access Journals (Sweden)

Hui Liu

2011-12-01

Full Text Available In order to make the dynamic characteristic simulation of the ordinary and planetary gears drive more accurate and more efficient , a generalized dynamic model of geared system is established including internal and external mesh gears in this paper. It is used to build a mathematical model, which achieves the auto judgment of the gear mesh state. We do not need to concern about active or passive gears any more, and the complicated power flow analysis can be avoided. With the numerical integration computation, the axis orbits diagram and dynamic gear mesh force characteristic are acquired and the results show that the dynamic response of translational displacement is greater when contacting line direction change is considered, and with the quickly change of direction of contacting line, the amplitude of mesh force would be increased, which easily causes the damage to the gear tooth. Moreover, compared with ordinary gear, dynamic responses of planetary gear would be affected greater by the gear backlash. Simulation results show the effectiveness of the generalized dynamic model and the mathematical model.

Gear cutting tools fundamentals of design and computation

CERN Document Server

Radzevich, Stephen P

2010-01-01

Presents the DG/K-based method of surface generation, a novel and practical mathematical method for designing gear cutting tools with optimal parameters. This book proposes a scientific classification for the various kinds of the gear machining meshes, discussing optimal designs of gear cutting tools.

46 CFR 58.25-20 - Piping for steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Piping for steering gear. 58.25-20 Section 58.25-20... MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-20 Piping for steering gear. (a) Pressure piping must... the hydraulic system can be readily recharged from within the steering-gear compartment and must be...

DESIGN IMPROVEMENT OF THE LOCOMOTIVE RUNNING GEARS

Directory of Open Access Journals (Sweden)

S. V. Myamlin

2013-09-01

Full Text Available Purpose. To determine the dynamic qualities of the mainline freight locomotives characterizing the safe motion in tangent and curved track sections at all operational speeds, one needs a whole set of studies, which includes a selection of the design scheme, development of the corresponding mathematical model of the locomotive spatial fluctuations, construction of the computer calculation program, conducting of the theoretical and then experimental studies of the new designs. In this case, one should compare the results with existing designs. One of the necessary conditions for the qualitative improvement of the traction rolling stock is to define the parameters of its running gears. Among the issues related to this problem, an important place is occupied by the task of determining the locomotive dynamic properties on the stage of projection, taking into account the selected technical solutions in the running gear design. Methodology. The mathematical modeling studies are carried out by the numerical integration method of the dynamic loading for the mainline locomotive using the software package «Dynamics of Rail Vehicles » («DYNRAIL». Findings. As a result of research for the improvement of locomotive running gear design it can be seen that the creation of the modern locomotive requires from engineers and scientists the realization of scientific and technical solutions. The solutions enhancing design speed with simultaneous improvement of the traction, braking and dynamic qualities to provide a simple and reliable design, especially the running gear, reducing the costs for maintenance and repair, low initial cost and operating costs for the whole service life, high traction force when starting, which is as close as possible to the ultimate force of adhesion, the ability to work in multiple traction mode and sufficient design speed. Practical Value. The generalization of theoretical, scientific and methodological, experimental studies aimed

Gear shift map design methodology for automotive transmissions

NARCIS (Netherlands)

Ngo, Viet Dac; Hofman, Theo; Steinbuch, Maarten; Serrarens, Alex

In this paper, a design methodology is developed to condtruct the gear shift map for the automotive transmissions used in conventional and hybrid electric vehicles. The methodology utilizes an optimal gear shift strategy to derive the optimal gear shift patterns over a wide range of driving

Surface micromachined counter-meshing gears discrimination device

Science.gov (United States)

Polosky, Marc A.; Garcia, Ernest J.; Allen, James J.

2000-12-12

A surface micromachined Counter-Meshing Gears (CMG) discrimination device which functions as a mechanically coded lock. Each of two CMG has a first portion of its perimeter devoted to continuous driving teeth that mesh with respective pinion gears. Each EMG also has a second portion of its perimeter devoted to regularly spaced discrimination gear teeth that extend outwardly on at least one of three levels of the CMG. The discrimination gear teeth are designed so as to pass each other without interference only if the correct sequence of partial rotations of the CMG occurs in response to a coded series of rotations from the pinion gears. A 24 bit code is normally input to unlock the device. Once unlocked, the device provides a path for an energy or information signal to pass through the device. The device is designed to immediately lock up if any portion of the 24 bit code is incorrect.

Power loss analysis in altered tooth-sum spur gearing

Directory of Open Access Journals (Sweden)

Sachidananda H. K.

2018-01-01

Full Text Available The main cause of power loss or dissipation of heat in case of meshed gears is due to friction existing between gear tooth mesh and is a major concern in low rotational speed gears, whereas in case of high operating speed the power loss taking place due to compression of air-lubricant mixture (churning losses and windage losses due to aerodynamic trial of air lubricant mixture which controls the total efficiency needs to be considered. Therefore, in order to improve mechanical efficiency it is necessary for gear designer during gear tooth optimization to consider these energy losses. In this research paper the power loss analysis for a tooth-sum of 100 altered by ±4% operating between a specified center distance is considered. The results show that negative altered tooth-sum gearing performs better as compared to standard and positive altered tooth-sum gearing.

Efficiency of fishing gears in the river Halda, Chittagong, Bangladesh

Directory of Open Access Journals (Sweden)

Mohammad Arshad-Ul-Alam

2015-12-01

Full Text Available To determine the catch efficiency of fishing gears, catch per unit effort (CPUEdata were collected for two years during January 2007 to December 2008 from the river Halda. Analyses were done to examine the variation of CPUE among gears, studied sections, months and years. The mean CPUE for pooled data of all gears was 2.247±0.265 kg.gear-1day-1 and 2.697±0.355 kg.gear-1day-1 for 2007 and 2008 respectively. Among eight gear categories, bag nets yielded the highest CPUE during 2007 (5.957±0.704 kg.gear-1day-1 and seine nets during 2008 (7.288±1.477 kg.gear-1day-1. Among 31 gear types, small meshed bag nets yielded the highest CPUE (18.065±6.660 and 15.69±4.479 kg.gear-1day-1 during 2007 and 2008 respectively. CPUE was highest during March-April and September-November periods. Analysis of variance showed significant difference among catch rates of different fishing gears. The CPUE differed significantly among different months for net fence, gill net, cast net and scoop net during 2007; and for seine net, net fence, bag net and cast net during 2008.

Hybrid Gear Preliminary Results-Application of Composites to Dynamic Mechanical Components

Science.gov (United States)

Handschuh, Robert F.; Roberts Gary D.; Sinnamon, R.; Stringer, David B.; Dykas, Brian D.; Kohlman, Lee W.

2012-01-01

Composite spur gears were fabricated and then tested at NASA Glenn Research Center. The composite material served as the web of the gear between the gear teeth and a metallic hub for mounting to the torque-applying shaft. The composite web was bonded only to the inner and outer hexagonal features that were machined from an initially all-metallic aerospace quality spur gear. The Hybrid Gear was tested against an all-steel gear and against a mating Hybrid Gear. As a result of the composite to metal fabrication process used, the concentricity of the gears were reduced from their initial high-precision value. Regardless of the concentricity error, the hybrid gears operated successfully for over 300 million cycles at 10000 rpm and 490 in.*lbs torque. Although the design was not optimized for weight, the composite gears were found to be 20% lighter than the all-steel gears. Free vibration modes and vibration/noise tests were also conduct to compare the vibration and damping characteristic of the Hybrid Gear to all-steel gears. The initial results indicate that this type of hybrid design may have a dramatic effect on drive system weight without sacrificing strength.

Nonlinear modeling of adaptive magnetorheological landing gear dampers under impact conditions

Science.gov (United States)

Ahuré Powell, Louise A.; Choi, Young T.; Hu, Wei; Wereley, Norman M.

2016-11-01

Adaptive landing gear dampers that can continuously adjust their stroking load in response to various operating conditions have been investigated for improving the landing performance of a lightweight helicopter. In prior work, adaptive magnetorheological (MR) landing gear dampers that maintained a constant peak stroking force of 4000 lbf across sink rates ranging from 6 to 12 ft s-1 were designed, fabricated and successfully tested. In this follow-on effort, it is desired to expand the high end of the sink rate range to hold the peak stroking load constant for sink rates ranging from 6 to 26 ft s-1, thus extending the high end of the speed range from 12 (in the first study) to 26 ft s-1. To achieve this increase, a spring-based relief valve MR landing gear damper was developed. In order to better understand the MR landing gear damper behavior, a modified nonlinear Bingham Plastic model was formulated, and it incorporates Darcy friction, viscous forces across the MR and relief valves to better account for the damper force behavior at higher speeds. In addition, gas pressure inside the MR damper piston is considered so the total damper force includes a gas force. The MR landing gear damper performance is characterized using drop tests, and the experiments are used to validate model predictions data at low and high nominal impact speeds up to 26 ft s-1 (shaft velocity of 9.6 ft s-1).

Surface contact fatigue failures in gears

CSIR Research Space (South Africa)

Fernandes, PJL

1997-06-01

Full Text Available Surface contact fatigue is the most common cause of gear failure. It results in damage to contacting surfaces which can significantly reduce the load-carrying capacity of components, and may ultimately lead to complete failure of a gear. Three types...

Gear Design Effects on the Performance of High Speed Helical Gear Trains as Used in Aerospace Drive Systems

Science.gov (United States)

Handschuh, R.; Kilmain, C.; Ehinger, R.; Sinusas, E.

2013-01-01

The performance of high-speed helical gear trains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction / torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High Speed Helical Gear Train Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160 to 250 degF) and lubricating jet pressure (60 to 80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears. The empirical data resulting from this study will be useful to the design of future helical gear train systems anticipated for next generation rotorcraft drive systems.

Investigation of Sideband Index Response to Prototype Gear Tooth Damage

Science.gov (United States)

Dempsey, Paula J.

2013-01-01

The objective of this analysis was to evaluate the ability of gear condition indicators (CI) to detect contact fatigue damage on spiral bevel gear teeth. Tests were performed in the NASA Glenn Spiral Bevel Gear Fatigue Rig on eight prototype gear sets (pinion/gear). Damage was initiated and progressed on the gear and pinion teeth. Vibration data was measured during damage progression at varying torque values while varying damage modes to the gear teeth were observed and documented with inspection photos. Sideband indexes (SI) and root mean square (RMS) CIs were calculated from the time synchronous averaged vibration data. Results found that both CIs respond differently to varying torque levels, damage levels and damage modes

Analytical Expressions of the Efficiency of Standard and High Contact Ratio Involute Spur Gears

Directory of Open Access Journals (Sweden)

Miguel Pleguezuelos

2013-01-01

Full Text Available Simple, traditional methods for computation of the efficiency of spur gears are based on the hypotheses of constant friction coefficient and uniform load sharing along the path of contact. However, none of them is accurate. The friction coefficient is variable along the path of contact, though average values can be often considered for preliminary calculations. Nevertheless, the nonuniform load sharing produced by the changing rigidity of the pair of teeth has significant influence on the friction losses, due to the different relative sliding at any contact point. In previous works, the authors obtained a nonuniform model of load distribution based on the minimum elastic potential criterion, which was applied to compute the efficiency of standard gears. In this work, this model of load sharing is applied to study the efficiency of both standard and high contact ratio involute spur gears (with contact ratio between 1 and 2 and greater than 2, resp.. Approximate expressions for the friction power losses and for the efficiency are presented assuming the friction coefficient to be constant along the path of contact. A study of the influence of some transmission parameters (as the gear ratio, pressure angle, etc. on the efficiency is also presented.

Two dimensional model of a permanent magnet spur gear

DEFF Research Database (Denmark)

Jørgensen, Frank Thorleif; Andersen, Torben Ole; Rasmussen, Peter Omand

2005-01-01

This paper presents calculation and measurement results of a high-performance permanent-magnetic gear. The analyzed permanent-magnetic gear has a gear ratio of 5.5 and is able to deliver 27 N/spl middot/m. The analysis has shown that special attention needs to be paid to the system where the gear...... is to be installed because of a low natural torsion spring constant. The analyzed gear was also constructed in practice in order to validate the analysis and predict the efficiency. The measured torque from the magnetic gear was only 16 N/spl middot/m reduced by the large end-effects. A systematic analysis...... of the loss components in the magnetic gear is also performed in order to figure out why the efficiency for the actual construction was only 81%. A large magnetic loss component originated in the bearings, where an unplanned extra bearing was necessary due to mechanical problems. Without the losses...

Finite Element Residual Stress Analysis of Planetary Gear Tooth

Directory of Open Access Journals (Sweden)

Jungang Wang

2013-01-01

Full Text Available A method to simulate residual stress field of planetary gear is proposed. In this method, the finite element model of planetary gear is established and divided to tooth zone and profile zone, whose different temperature field is set. The gear's residual stress simulation is realized by the thermal compression stress generated by the temperature difference. Based on the simulation, the finite element model of planetary gear train is established, the dynamic meshing process is simulated, and influence of residual stress on equivalent stress of addendum, pitch circle, and dedendum of internal and external meshing planetary gear tooth profile is analyzed, according to non-linear contact theory, thermodynamic theory, and finite element theory. The results show that the equivalent stresses of planetary gear at both meshing and nonmeshing surface are significantly and differently reduced by residual stress. The study benefits fatigue cracking analysis and dynamic optimization design of planetary gear train.

Modeling of automotive driveline system for reducing gear rattles

Science.gov (United States)

Shangguan, Wen-Bin; Liu, Xue-Lai; Yin, Yuming; Rakheja, Subhash

2018-03-01

A nonlinear torsional model for a driveline system with 4 degrees of freedom is proposed for studying gear rattle if a car is at idle. The time-varying meshing stiffness of geared teeth, gear backlash, and the damping from oil film are included in the model. The dynamic responses of the driveline system, such as clutch angular displacement, meshing force and relative displacement between geared teeth, are calculated using the presented model. The influences of stiffness and damping of a clutch on gear rattle of geared teeth in a generic transmission are investigated. Based on the calculation and analysis results, a design guideline to select clutch's stiffness and damping is developed to reduce gear rattle for a car at idle. Taking a generic driveline system of a passenger car as an example, the developed method is experimentally validated by comparing the baseline clutch and revised clutch, in terms of the measured noise inside engine compartment and cab and vibrations at transmission housing.

78 FR 68817 - Proposed Information Collection; Comment Request; Northeast Region Gear Identification

Science.gov (United States)

2013-11-15

... gear type being used to help prevent gear conflicts. II. Method of Collection No information is... certain types of fishing gear mark the gear with specified information. The gear marking requirements... for marking several strings of a given gear type, or may use multiple different gear types that...

The theory and practice of worm gear drives

CERN Document Server

Dudás, Ilés

2005-01-01

Worm gears are special gears that resemble screws, and can be used to drive other gears. Worm gears, enable two non-touching shafts in a machine to mesh (join) together. This publication, unique in that it combines both theoretical and practical design aspects, including the latest results of research and development, provides detailed treatment of the theory and production of worm drives, as well as the overarching subject of production geometry of helicoidal surfaces.Included are mathematical models for a number of practical applications; a description of dressing equipment r

46 CFR 167.65-25 - Steering gear tests.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Steering gear tests. 167.65-25 Section 167.65-25... SHIPS Special Operating Requirements § 167.65-25 Steering gear tests. On all nautical school ships making voyages of more than 48 hours' duration, the entire steering gear, the whistle, the means of...

Research on cutting vibration characteristics of face-milling involute gear

Directory of Open Access Journals (Sweden)

Chengzhe JIN

2017-10-01

Full Text Available Traditional machining methods, such as gear hobbing, gear shaping and gear milling, etc, are commonly used for cutting machining of gear tooth profile, which cannot meet huge machining demand of gears to a certain extent. This article proposes to utilize a face-milling machining method in involute gear machining, which can be used to reduce production cost effectively. Cutting vibration generated during cutting machining has a direct effect on the machining accuracy and machined surface quality of workpiece. Therefore, it is desiderated to perform in-depth research regarding this issue. ADAMS software was used to establish a rigid-flexible coupling virtual prototyping model of face-milling gear milling system and a cutting vibration system model. Cutting vibration analysis was performed for face-milling gear by adopting quick sine frequency sweep method, so that the frequency response characteristics of workpiece in three directions X, Y and Z and space were acquired. The research results will provide reference and theoretical foundation for actual application of face-milling gear machining technology.

Variable gearing in a biologically inspired pneumatic actuator array

International Nuclear Information System (INIS)

Azizi, Emanuel; Roberts, Thomas J

2013-01-01

A fundamental feature of pennate muscles is that muscle fibers are oriented at an angle to the line of action and rotate as they shorten, becoming more oblique throughout a contraction. This change in fiber orientation (pennation angle) can amplify the shortening velocity of a fiber and increase output velocity of the muscle. The velocity advantage resulting from dynamic changes in pennation angle can be characterized as a gear ratio (muscle velocity/fiber velocity). A recent study has shown that a pennate muscle's gear ratio varies automatically depending on the load such that a muscle operates with a high gear during rapid contractions and low gear during forceful contractions. We examined whether this variable gearing behavior can be replicated in a pennate array of artificial muscles. We used McKibben type pneumatic actuators, which shorten in tension when filled with compressed gas. Similar to muscle fibers, the actuators expand radially during shortening, a feature thought to be a critical part of the variable gearing mechanism in pennate muscles. We arranged McKibben actuators in an array oriented to mimic a pennate muscle, and quantified the system's gear ratio during contraction against a range of loads. Video was used to measure the gear ratio during each contraction. We find that similar to pennate muscles, the gear ratio decreases significantly with increasing load and that variable gearing results from load-dependent variation in the amount of actuator rotation. These results support the idea that variable gearing in pennate muscles is mediated by difference is fiber rotation and the direction of muscle bulging. The behavior of our artificial muscle array also highlights the potential benefits of bio-inspired architectures in artificial muscle arrays, including the ability to vary force and speed automatically in response to variable loading conditions. (paper)

Variable gearing in a biologically inspired pneumatic actuator array.

Science.gov (United States)

Azizi, Emanuel; Roberts, Thomas J

2013-06-01

A fundamental feature of pennate muscles is that muscle fibers are oriented at an angle to the line of action and rotate as they shorten, becoming more oblique throughout a contraction. This change in fiber orientation (pennation angle) can amplify the shortening velocity of a fiber and increase output velocity of the muscle. The velocity advantage resulting from dynamic changes in pennation angle can be characterized as a gear ratio (muscle velocity/fiber velocity). A recent study has shown that a pennate muscle's gear ratio varies automatically depending on the load such that a muscle operates with a high gear during rapid contractions and low gear during forceful contractions. We examined whether this variable gearing behavior can be replicated in a pennate array of artificial muscles. We used McKibben type pneumatic actuators, which shorten in tension when filled with compressed gas. Similar to muscle fibers, the actuators expand radially during shortening, a feature thought to be a critical part of the variable gearing mechanism in pennate muscles. We arranged McKibben actuators in an array oriented to mimic a pennate muscle, and quantified the system's gear ratio during contraction against a range of loads. Video was used to measure the gear ratio during each contraction. We find that similar to pennate muscles, the gear ratio decreases significantly with increasing load and that variable gearing results from load-dependent variation in the amount of actuator rotation. These results support the idea that variable gearing in pennate muscles is mediated by difference is fiber rotation and the direction of muscle bulging. The behavior of our artificial muscle array also highlights the potential benefits of bio-inspired architectures in artificial muscle arrays, including the ability to vary force and speed automatically in response to variable loading conditions.

VARIABLE GEARING IN A BIOLOGICALLY-INSPIRED PNEUMATIC ACTUATOR ARRAY

Science.gov (United States)

Azizi, Emanuel; Roberts, Thomas J.

2013-01-01

A fundamental feature of pennate muscles is that muscle fibers are oriented at an angle to the line of action and rotate as they shorten, becoming more oblique throughout a contraction. This change in fiber orientation (pennation angle) can amplify the shortening velocity of a fiber and increase output velocity of the muscle. The velocity advantage resulting from dynamic changes in pennation angle can be characterized as a gear ratio (muscle velocity/fiber velocity). A recent study has shown that a pennate muscle’s gear ratio varies automatically depending on the load such that a muscle operates with a high gear during rapid contractions and low gear during forceful contractions. We examined whether this variable gearing behavior can be replicated in a pennate array of artificial muscles. We used McKibben type pneumatic actuators, which shorten in tension when filled with compressed gas. Similar to muscle fibers, the actuators expand radially during shortening, a feature thought to be a critical part of the variable gearing mechanism in pennate muscles. We arranged McKibben actuators in an array oriented to mimic a pennate muscle, and quantified the system’s gear ratio during contraction against a range of loads. Video was used to measure the gear ratio during each contraction. We find that similar to pennate muscles, the gear ratio decreases significantly with increasing load and that variable gearing results from load-dependent variation in the amount of actuator rotation. These results support the idea that variable gearing in pennate muscles is mediated by difference is fiber rotation and the direction of muscle bulging. The behavior of our artificial muscle array also highlights the potential benefits of bio-inspired architectures in artificial muscle arrays, including the ability to vary force and speed automatically in response to variable loading conditions. PMID:23462288

Tooth bending fatigue failures in gears

CSIR Research Space (South Africa)

Fernandes, PJL

1996-09-01

Full Text Available . It results in progressive damage to gear teeth and ultimately leads to complete failure of the gear. The characteristics of this failure mode are discussed in detail and a number of actual case studies are presented which show the occurrence of this failure...

LCD denoise and the vector mutual information method in the application of the gear fault diagnosis under different working conditions

Science.gov (United States)

Xiangfeng, Zhang; Hong, Jiang

2018-03-01

In this paper, the full vector LCD method is proposed to solve the misjudgment problem caused by the change of the working condition. First, the signal from different working condition is decomposed by LCD, to obtain the Intrinsic Scale Component (ISC)whose instantaneous frequency with physical significance. Then, calculate of the cross correlation coefficient between ISC and the original signal, signal denoising based on the principle of mutual information minimum. At last, calculate the sum of absolute Vector mutual information of the sample under different working condition and the denoised ISC as the characteristics to classify by use of Support vector machine (SVM). The wind turbines vibration platform gear box experiment proves that this method can identify fault characteristics under different working conditions. The advantage of this method is that it reduce dependence of man’s subjective experience, identify fault directly from the original data of vibration signal. It will has high engineering value.

Face-gear drives: Design, analysis, and testing for helicopter transmission applications

Science.gov (United States)

Litvin, F. L.; Wang, J.-C.; Bossler, R. B., Jr.; Chen, Y.-J. D.; Heath, G.; Lewicki, D. G.

1992-01-01

The use of face-gears in helicopter transmissions was explored. A light-weight, split-torque transmission design utilizing face-gears is described. Face-gear design and geometry were investigated. Topics included tooth generation, limiting inner and outer radii, tooth contact analysis, contact ratio, gear eccentricity, grinding, and structural stiffness. Design charts were developed to determine minimum and maximum face-gear inner and outer radii. An analytical study showed that the face-gear drive is relatively insensitive to gear misalignment with respect to transmission errors, but the tooth contact is affected by misalignment. A method of localizing the bearing contact to permit operation with misalignment was explored. Two new methods for grinding of the face-gear tooth surfaces were also investigated. The proper choice of shaft stiffness enabled good load sharing in the split-torque transmission design. Face-gear experimental studies were also conducted. These tests demonstrated the feasibility of face-gears in high-speed, high-load applications such as helicopter transmissions.

Shimmy of Aircraft Main Landing Gears

NARCIS (Netherlands)

Besselink, I.J.M.

2000-01-01

The landing gear is an important aircraft system, which has to meet many different design requirements. It is a highly loaded structure, which is designed for minimum weight. Shimmy is a dynamic instability of the landing gear, which is caused by the interaction of the dynamic behaviour of the

From design to manufacturing of asymmetric teeth gears using computer application

Science.gov (United States)

Suciu, F.; Dascalescu, A.; Ungureanu, M.

2017-05-01

The asymmetric cylindrical gears, with involutes teeth profiles having different base circle diameters, are nonstandard gears, used with the aim to obtain better function parameters for the active profile. We will expect that the manufacturing of these gears became possible only after the design and realization of some specific tools. The paper present how the computer aided design and applications developed in MATLAB, for obtain the geometrical parameters, in the same time for calculation some functional parameters like stress and displacements, transmission error, efficiency of the gears and the 2D models, generated with AUTOLISP applications, are used for computer aided manufacturing of asymmetric gears with standard tools. So the specific tools considered one of the disadvantages of these gears are not necessary and implicitly the expected supplementary costs are reduced. The calculus algorithm established for the asymmetric gear design application use the „direct design“ of the spur gears. This method offers the possibility of determining first the parameters of the gears, followed by the determination of the asymmetric gear rack’s parameters, based on those of the gears. Using original design method and computer applications have been determined the geometrical parameters, the 2D and 3D models of the asymmetric gears and on the base of these models have been manufacturing on CNC machine tool asymmetric gears.

Rigid MATLAB drivetrain model of a 500 kW wind turbine for predicting maximum gear tooth stresses in a planetary gearbox using multibody gear constraints

DEFF Research Database (Denmark)

Jørgensen, Martin Felix; Pedersen, Niels Leergaard; Sørensen, Jens Nørkær

2014-01-01

multiple planetary gears are not taken into account. Finite Element Method (FEM) calculations show that when the wind turbine runs close to the maximum wind speed, the maximum gear tooth stress is in the range of 500–700 MPa, which is considered to be realistic using a “worst-case” method. The presented...... for not only transferring torque but also for calculating the gear tooth and internal body reaction forces. The method is appropriate for predicting gear tooth stresses without considering all the complexity of gear tooth geometries. This means that, e.g. gear tooth load-sharing and load-distribution among...

Architectural Drawing - an Animate Field

DEFF Research Database (Denmark)

Hougaard, Anna Katrine

2015-01-01

Architectural drawing is changing because architects today draw with computers. Due to this change digital diagrams employed by computational architectural practices are often emphasized as powerful structures of control and organisation in the design process. But there are also diagrams, which do...... ways of directing behaviour of artefacts and living things without controlling this behaviour completely. I analyse a musical composition by John Cage as an example of a sketch diagram, and then hypothesize that orthogonal, architectural drawing can work in similar ways. Thereby I hope to point out...... important affordance of architectural drawing as a ¬hybrid between the openness of hand-sketching and the rule-based-ness of diagramming, an affordance which might be useful in the migrational zone of current architectural drawing where traditional hand drawing techniques and computer drawing techniques...

Automated drawing generation system

International Nuclear Information System (INIS)

Yoshinaga, Toshiaki; Kawahata, Junichi; Yoshida, Naoto; Ono, Satoru

1991-01-01

Since automated CAD drawing generation systems still require human intervention, improvements were focussed on an interactive processing section (data input and correcting operation) which necessitates a vast amount of work. As a result, human intervention was eliminated, the original objective of a computerized system. This is the first step taken towards complete automation. The effects of development and commercialization of the system are as described below. (1) The interactive processing time required for generating drawings was improved. It was determined that introduction of the CAD system has reduced the time required for generating drawings. (2) The difference in skills between workers preparing drawings has been eliminated and the quality of drawings has been made uniform. (3) The extent of knowledge and experience demanded of workers has been reduced. (author)

Nonlinear dynamics modelling of multistage micro-planetary gear transmission

Directory of Open Access Journals (Sweden)

Li Jianying

2018-01-01

Full Text Available The transmission structure of a 2K-H multistage micro-planetary gear transmission reducer is described in detail, and three assumptions are supposed in dynamic modelling. On basis of these assumptions, a three stages 2K-H micro-planetary gear transmission dynamic model is established, in which the relative displacement each meshing gear pairs can be obtained after including the comprehensive transmission error. According to gear kinematics, the friction arms between the sun gear, the ring gear and the nth planet are also obtained, and the friction coefficient in the mixed elastohydrodynamic lubrication is considered, the transmission system motion differential equations are obtained, including above factors and the time-varying meshing stiffness, damping and backlash, inter-stage coupling stiffness, it can be provided an theoretical foundation for further analysing the parameter sensitivity, dynamic stability and designing.

Engineering science research issues in high power density transmission dynamics for aerospace applications. [rotorcraft geared rotors

Science.gov (United States)

Singh, Rajendra; Houser, Donald R.

1993-01-01

This paper discusses analytical and experimental approaches that will be needed to understand dynamic, vibro-acoustic and design characteristics of high power density rotorcraft transmissions. Complexities associated with mathematical modeling of such systems will be discussed. An overview of research work planned during the next several years will be presented, with emphasis on engineering science issues such as gear contact mechanics, multi-mesh drive dynamics, parameter uncertainties, vibration transmission through bearings, and vibro-acoustic characteristics of geared rotor systems and housing-mount structures. A few examples of work in progress are cited.

The influence of stimulus format on drawing--a functional imaging study of decision making in portrait drawing.

Science.gov (United States)

Miall, R C; Nam, Se-Ho; Tchalenko, J

2014-11-15

To copy a natural visual image as a line drawing, visual identification and extraction of features in the image must be guided by top-down decisions, and is usually influenced by prior knowledge. In parallel with other behavioral studies testing the relationship between eye and hand movements when drawing, we report here a functional brain imaging study in which we compared drawing of faces and abstract objects: the former can be strongly guided by prior knowledge, the latter less so. To manipulate the difficulty in extracting features to be drawn, each original image was presented in four formats including high contrast line drawings and silhouettes, and as high and low contrast photographic images. We confirmed the detailed eye-hand interaction measures reported in our other behavioral studies by using in-scanner eye-tracking and recording of pen movements with a touch screen. We also show that the brain activation pattern reflects the changes in presentation formats. In particular, by identifying the ventral and lateral occipital areas that were more highly activated during drawing of faces than abstract objects, we found a systematic increase in differential activation for the face-drawing condition, as the presentation format made the decisions more challenging. This study therefore supports theoretical models of how prior knowledge may influence perception in untrained participants, and lead to experience-driven perceptual modulation by trained artists. Copyright © 2014. Published by Elsevier Inc.

Work security in a global economy.

Science.gov (United States)

Rosskam, Ellen

2003-01-01

Work security is a fundamental right of all working people. After World War II, the welfare state became an intrinsic part of the "Golden Age" of capitalism, in which universal prosperity seemed attainable. Workers' organizations frequently played a crucial role in policy decisions that promoted full employment, income stability, and equitable treatment of workers. Today's world order is quite different. Globalization in its present form is a major obstacle to work security. Globalization is not simply a market-driven phenomenon. It is a political and ideological movement that grants authority to capital over governments and labor. This transfer of authority hinders national efforts to promote work security and may impact the well-being of communities worldwide. In the absence of domestic autonomy, international labor standards are needed to protect social welfare. They should be geared toward curbing unemployment, poverty, and social exclusion in the global economy. The article looks at three initiatives to promote global work security.

Mixed Movements/performance-based drawing

DEFF Research Database (Denmark)

Brabrand, Helle

2010-01-01

Mixed Movements is a research project engaged in performance-based architectural drawing. The project experiments with drawing-series as montages of materials and forces, making the drawing appear in its changing character. The moving components are conditioned by different circumstances...... that question each other, working as well with space-time motives as with expressions and techniques. A series poses questions both to the kind of forces it raises as well as to the kind of sensual affects it produces – to how the body resonates with the rhythms and tensions that appear in the drawing....... A drawing-series is then both a machine, a diagram, and an appearance, what we call a resonance-model, creating links between tectonic and drawing constructions, kinaesthetic competences and actual body-movements....

A multi objective optimization of gear cutting in WEDM of Inconel 718 using TOPSIS method

Directory of Open Access Journals (Sweden)

K.D. Mohapatra

2017-07-01

Full Text Available The present paper deals with the experimental analysis and multi objective optimization of gear cutting process of Inconel 718 using WEDM. The objective of the present work is to optimize the parameters in order to maximize the material removal rate and minimize the kerf in a gear cutting process to get the optimum value. The MRR and kerf play a major role in optimizing the parameters in WEDM process. The experiment is carried out in the wire EDM machine using brass wire as the electrode, Inconel 718 as the work-piece material and distilled water as the dielectric. The design array is created by using Design of Experiment in a Taguchi L16 orthogonal array repeated once. The gear has a base diameter of 20 mm, addendum diameter of 22.5 mm and a pressure angle of 20º with 16 numbers of teeth. The machining operation is carried out by taking 3 input parameters at 4 different levels each. The output parameters such as Material Removal rate and Kerf width were obtained and optimized using TOPSIS method to know the optimum setting. Microstructural analysis of both material and wire were studied to know the various defects during the machining operation. Various plots were obtained to know the effects of the process parameters in WEDM. A regression model was also obtained to validate the statistical model values with the experimental. ANOVA table and Response table were carried out to know the significant parameters and rank respectively in the Wire EDM process. Surface roughness, Addendum and Tooth width of gears were also found out at the optimum settings. The optimum setting of the gear obtained can be used to produce high quality gears and can also be applied for future findings.

Osmotically-driven membrane processes for water reuse and energy recovery

Science.gov (United States)

Achilli, Andrea

Osmotically-driven membrane processes are an emerging class of membrane separation processes that utilize concentrated brines to separate liquid streams. Their versatility of application make them an attractive alternative for water reuse and energy production/recovery. This work focused on innovative applications of osmotically-driven membrane processes. The novel osmotic membrane bioreactor (OMBR) system for water reuse was presented. Experimental results demonstrated high sustainable flux and relatively low reverse diffusion of solutes from the draw solution into the mixed liquor. Membrane fouling was minimal and controlled with osmotic backwashing. The OMBR system was found to remove greater than 99% of organic carbon and ammonium-nitrogen. Forward osmosis (FO) can employ different draw solution in its process. More than 500 inorganic compounds were screened as draw solution candidates, the desktop screening process resulted in 14 draw solutions suitable for FO applications. The 14 draw solutions were then tested in the laboratory to evaluate water flux and reverse salt diffusion through the membrane. Results indicated a wide range of water flux and reverse salt diffusion depending on the draw solution utilized. Internal concentration polarization was found to lower both water flux and reverse salt diffusion by reducing the draw solution concentration at the interface between the support and dense layer of the membrane. A small group of draw solutions was found to be most suitable for FO processes with currently available FO membranes. Another application of osmotically-driven membrane processes is pressure retarded osmosis (PRO). PRO was investigated as a viable source of renewable energy. A PRO model was developed to predict water flux and power density under specific experimental conditions. The predictive model was tested using experimental results from a bench-scale PRO system. Previous investigations of PRO were unable to verify model predictions due to

Prediction of Landing Gear Noise Reduction and Comparison to Measurements

Science.gov (United States)

Lopes, Leonard V.

2010-01-01

Noise continues to be an ongoing problem for existing aircraft in flight and is projected to be a concern for next generation designs. During landing, when the engines are operating at reduced power, the noise from the airframe, of which landing gear noise is an important part, is equal to the engine noise. There are several methods of predicting landing gear noise, but none have been applied to predict the change in noise due to a change in landing gear design. The current effort uses the Landing Gear Model and Acoustic Prediction (LGMAP) code, developed at The Pennsylvania State University to predict the noise from landing gear. These predictions include the influence of noise reduction concepts on the landing gear noise. LGMAP is compared to wind tunnel experiments of a 6.3%-scale Boeing 777 main gear performed in the Quiet Flow Facility (QFF) at NASA Langley. The geometries tested in the QFF include the landing gear with and without a toboggan fairing and the door. It is shown that LGMAP is able to predict the noise directives and spectra from the model-scale test for the baseline configuration as accurately as current gear prediction methods. However, LGMAP is also able to predict the difference in noise caused by the toboggan fairing and by removing the landing gear door. LGMAP is also compared to far-field ground-based flush-mounted microphone measurements from the 2005 Quiet Technology Demonstrator 2 (QTD 2) flight test. These comparisons include a Boeing 777-300ER with and without a toboggan fairing that demonstrate that LGMAP can be applied to full-scale flyover measurements. LGMAP predictions of the noise generated by the nose gear on the main gear measurements are also shown.

On optimization of internal/external spur gears tooth bending strength

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2014-01-01

level at the tooth root. As with most machine elements the design/geometry is defined in standards (ISO). The present work focuses on changing the tooth root design of both external and internal gears, in order to improve the stress concentration factor. The design changes made are compliant...

46 CFR 97.37-33 - Instructions for changing steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Instructions for changing steering gear. 97.37-33... steering gear. (a) Instructions in at least 1/2 inch letters and figures shall be posted in the steering... gear. Each clutch, gear, wheel, lever, valve, or switch which is used during the changeover shall be...

46 CFR 58.25-10 - Main and auxiliary steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Main and auxiliary steering gear. 58.25-10 Section 58.25... AUXILIARY MACHINERY AND RELATED SYSTEMS Steering Gear § 58.25-10 Main and auxiliary steering gear. (a) Power-operated main and auxiliary steering gear must be separate systems that are independent throughout their...

Research of the load distribution in the wave kinematic reducer with a modified tooth profile and dependence of the load abilities in proportion to its gear ratio and overall dimensions

Science.gov (United States)

Stepanova, D. L.; Nikulin, P. A.

2017-01-01

Nowadays, there are many types of reducers based on work of gear trains, which transfer torque. The most popular reducers are with such type of gearing as an involute gear, a worm drive and an eccentrically cycloid gear. A new type of the reducer will be represented in this work. It is a wave reducer with the modified profile of the tooth close to the profile of the tooth of Novikov gearing. So such reducers can be widely used in drives of difficult technical mechanisms, for example, in mechatronics, robotics and in drives of exact positioning. In addition, the distribution of loading in gearing of teeth of a reducer was analyzed in this paper. It proves that the modified profile of the tooth allows distributing loading to several teeth in gearing. As a result, an admissible loading ability of a reducer becomes higher. The aim of the research is to define a possibility to reduce overall dimensions of a reducer without changing the gear ratio or to increase the gear ratio without changing overall dimensions. So, the result of this work will be used in further research.

Order of blood draw

DEFF Research Database (Denmark)

Cornes, Michael; van Dongen-Lases, Edmée; Grankvist, Kjell

2017-01-01

does occur if order of draw is not followed during blood collection and when performing venipuncture under less than ideal circumstances, thus putting patient safety at risk. Moreover, given that order of draw is not difficult to follow and knowing that ideal phlebotomy conditions and protocols...... Medicine Working Group for the Preanalytical Phase (EFLM WG-PRE) provides an overview and summary of the literature with regards to order of draw in venous blood collection. Given the evidence presented in this article, the EFLM WG-PRE herein concludes that a significant frequency of sample contamination...

Hydromechanical transmission with three simple planetary assemblies, one sun gear being mounted on the output shaft and the other two on a common shaft connected to an input-driven hydraulic module

Science.gov (United States)

Orshansky, Jr., deceased, Elias; Weseloh, William E.

1978-01-01

A power transmission having three simple planetary assemblies, each having its own carrier and its own planet, sun, and ring gears. A speed-varying module is connected in driving relation to the input shaft and in driving relationship to the sun gears of the first two planetary assemblies, these two sun gears being connected together on a common shaft. The speed-varying means may comprise a pair of hydraulic units hydraulically interconnected so that one serves as a pump while the other serves as a motor and vice versa, one of the units having a variable stroke and being connected in driving relation to the input shaft, the other unit, which may have a fixed stroke, being connected in driving relation to the sun gears. The input shaft is also connected to drive the second ring gear and, furthermore is clutchable to the carrier of the third planetary assembly. A brake grounds the first carrier in the first range and in reverse and causes drive to be delivered to the output through the first ring gear in a hydrostatic mode. The carrier of the second planetary assembly drives the ring gear of the third planetary assembly, which is clutchable to the output shaft, and the sun gear of the third planetary assembly is mounted rigidly to the output shaft.

Elasto-dynamic analysis of a gear pump-Part IV: Improvement in the pressure distribution modelling

Science.gov (United States)

Mucchi, E.; Dalpiaz, G.; Fernàndez del Rincòn, A.

2015-01-01

This work concerns external gear pumps for automotive applications, which operate at high speed and low pressure. In previous works of the authors (Part I and II, [1,2]), a non-linear lumped-parameter kineto-elastodynamic model for the prediction of the dynamic behaviour of external gear pumps was presented. It takes into account the most important phenomena involved in the operation of this kind of machine. The two main sources of noise and vibration are considered: pressure pulsation and gear meshing. The model has been used in order to foresee the influence of working conditions and design modifications on vibration generation. The model experimental validation is a difficult task. Thus, Part III proposes a novel methodology for the validation carried out by the comparison of simulations and experimental results concerning forces and moments: it deals with the external and inertial components acting on the gears, estimated by the model, and the reactions and inertial components on the pump casing and the test plate, obtained by measurements. The validation is carried out by comparing the level of the time synchronous average in the time domain and the waterfall maps in the frequency domain, with particular attention to identify system resonances. The validation results are satisfactory global, but discrepancies are still present. Moreover, the assessed model has been properly modified for the application to a new virtual pump prototype with helical gears in order to foresee gear accelerations and dynamic forces. Part IV is focused on improvements in the modelling and analysis of the phenomena bound to the pressure distribution around the gears in order to achieve results closer to the measured values. As a matter of fact, the simulation results have shown that a variable meshing stiffness has a notable contribution on the dynamic behaviour of the pump but this is not as important as the pressure phenomena. As a consequence, the original model was modified with

A New Design of the Universal Test Rig to Measure the Wear Characterizations of Polymer Acetal Gears (Spur, Helical, Bevel, and Worm

Directory of Open Access Journals (Sweden)

Samy Yousef

2015-01-01

Full Text Available This work aims to study the wear characterization of common types of acetal polymer gears (spur, helical, bevel, and worm using a new TS universal test rig, in order to obtain reliable results and as a reference when compared with acetal nanocomposite gears later. The TS universal test rig consists of three different units that are connected by a main driver shaft and a pair of constantly meshing metal spur gears, which transfer power to the bevel and worm test units. The first unit is used to test the bevel gears, the second unit is used to test the spur and helical gears, and the third unit is used to test the worm gears. The loading mechanism is similarly designed to block the brake mechanism. Hobbing and milling machines were used to machine an injection-moulded polymer flanges and produce the tested gears. All gear pairs, except the worm gear, have identical gear ratios. The experiments were performed at speed 1420 rpm and the torque was 4 Nm. The results showed that the wear rates (in the form of weight loss of spur gears were consistent with the previous results and the other gear types had larger wear rates.

Dynamic characteristic of electromechanical coupling effects in motor-gear system

Science.gov (United States)

Bai, Wenyu; Qin, Datong; Wang, Yawen; Lim, Teik C.

2018-06-01

Dynamic characteristics of an electromechanical model which combines a nonlinear permeance network model (PNM) of a squirrel-cage induction motor and a coupled lateral-torsional dynamic model of a planetary geared rotor system is analyzed in this study. The simulations reveal the effects of internal excitations or parameters like machine slotting, magnetic saturation, time-varying mesh stiffness and shaft stiffness on the system dynamics. The responses of the electromechanical system with PNM motor model are compared with those responses of the system with dynamic motor model. The electromechanical coupling due to the interactions between the motor and gear system are studied. Furthermore, the frequency analysis of the electromechanical system dynamic characteristics predicts an efficient way to detect work condition of unsymmetrical voltage sag.

The study about planetary gearbox virtual prototyping with nonlinear gear contact characteristics

International Nuclear Information System (INIS)

Yin Huabing; Zhou Guangming

2010-01-01

The virtual prototypes of gear transmission system built in most multi-body dynamic software have difficulties in describing the gear mesh characteristics. The gear mesh contact is modelled as rigid contact and this is not accurate for the gear mesh contact, which is elastic or flexible. The gear contact formula used in the multi-body dynamic software does not reveal the gear contact nonlinear stiffness characteristic. The model built with gear meshing contact is difficult to solve because of its time-consuming algorithm. In the paper a new method is put forward to build the virtual prototype of planetary gearbox system according to the nonlinear mesh stiffness and mesh phase obtained through FEM models. This new FEM method of gear mesh stiffness calculation is much more accurate than the common formulas. The gear mesh nonlinear stiffness of sun gear- pinion and pinion-ring gear of all the planetary gear sets in gearbox are obtained through MATALB code, which is used to read and plot the analyzing result data. The gear mesh phase differences between different pinions with suns or rings of different planetary gear set can be also obtained. With all these data modelled in simulink (or other software) and integrated with the multi-body dynamic planetary gearbox model and the gear meshing contact problem in multi-body gear models is solved easily and accurately. The interfaces for gear mesh stiffness and mesh phases are designed for multi-body dynamic model and simulink. The nonlinear planetary gear set prototyping models are integrated to become the whole planetary gear box model and the whole vehicle system model built in multi-body dynamic software can be integrated to simulate different duty conditions. At last high speed input is put into the nonlinear planetary transmission model and the different duty cases are simulated. The dynamic characteristics of different parts are obtained. The dynamic characteristic comparison between nonlinear and linear models is made

Design and Analysis of Landing Gear Mechanic Structure for the Mine Rescue Carrier Robot

Directory of Open Access Journals (Sweden)

Wei Juan

2014-06-01

Full Text Available The landing gear is used as a channel for the secondary detecting robot to leave and return the first carrier robot in the coal mine rescue robot system. The planar linkage mechanism, which is composed of offset rocker-slider mechanism and double-rocker mechanism, is designed according to the function and working principle of the landing gear. It could realize the 120° rotation of the flap with a motor driving the slider. The size calculation of the planar linkage mechanism is completed according to its workspace. The geometric modeling of the landing gear is made in the SolidWorks, and the basic Kinematic analysis is carried out by the simulation module of Motion. And the movement rule about angular displacement and angular velocity of the linkage mechanism could be obtained under given input condition, which could verify the system’s feasibility. It provides a theoretical basis for the structure design and engineering application of linkage mechanism and an applying basis for the coal mine rescue robot.

Detection and Localization of Tooth Breakage Fault on Wind Turbine Planetary Gear System considering Gear Manufacturing Errors

Directory of Open Access Journals (Sweden)

Y. Gui

2014-01-01

Full Text Available Sidebands of vibration spectrum are sensitive to the fault degree and have been proved to be useful for tooth fault detection and localization. However, the amplitude and frequency modulation due to manufacturing errors (which are inevitable in actual planetary gear system lead to much more complex sidebands. Thus, in the paper, a lumped parameter model for a typical planetary gear system with various types of errors is established. In the model, the influences of tooth faults on time-varying mesh stiffness and tooth impact force are derived analytically. Numerical methods are then utilized to obtain the response spectra of the system with tooth faults with and without errors. Three system components (including sun, planet, and ring gears with tooth faults are considered in the discussion, respectively. Through detailed comparisons of spectral sidebands, fault characteristic frequencies of the system are acquired. Dynamic experiments on a planetary gear-box test rig are carried out to verify the simulation results and these results are of great significances for the detection and localization of tooth faults in wind turbines.

Exploration of polyelectrolytes as draw solutes in forward osmosis processes

KAUST Repository

Ge, Qingchun

2012-03-01

The development of the forward osmosis (FO) process has been constrained by the slow development of appropriate draw solutions. Two significant concerns related to draw solutions are the draw solute leakage and intensiveenergy requirement in recycling draw solutes after the FO process. FO would be much attractive if there is no draw solute leakage and the recycle of draw solutes is easy and economic. In this study, polyelectrolytes of a series of polyacrylic acid sodium salts (PAA-Na), were explored as draw solutes in the FO process. The characteristics of high solubility in water and flexibility in structural configuration ensure the suitability of PAA-Na as draw solutes and their relative ease in recycle through pressure-driven membrane processes. The high water flux with insignificant salt leakage in the FO process and the high salt rejection in recycle processes reveal the superiority of PAA-Na to conventional ionic salts, such as NaCl, when comparing their FO performance via the same membranes. The repeatable performance of PAA-Na after recycle indicates the absence of any aggregation problems. The overall performance demonstrates that polyelectrolytes of PAA-Na series are promising as draw solutes, and the new concept of using polyelectrolytes as draw solutes in FO processes is applicable. © 2011 Elsevier Ltd.

Gearing.

Science.gov (United States)

1985-12-01

trichloroethyl phosphite and a phosphate ester containing a pentachlorphenyl radical. Most of the Asperity heights phosphorous compounds in gear oils...108) found that phosphorous compounds chemisorption. These boundary films can be thinner than ( 1 0 u ts n 0.025 pm (I in ) or several microinches thick...Pinion 1 .. dibutylxanthic acid disulfide. Ŗ %- Lead soaps have been used in lubricants for many 02 years. They resist the wiping and sliding action in

30 CFR 75.1404 - Automatic brakes; speed reduction gear.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic brakes; speed reduction gear. 75.1404... Automatic brakes; speed reduction gear. [Statutory Provisions] Each locomotive and haulage car used in an... permit automatic brakes, locomotives and haulage cars shall be subject to speed reduction gear, or other...

Gear-shaft linkage, especially for nuclear reactor coolant pumps

International Nuclear Information System (INIS)

Delaunois, T.; Lefevre, R.

1990-01-01

The pump comprises: - inlet and outlet channels for the pumped fluid - a rotating shaft - a gear wheel mounted on the shaft by an axial locking nut which can support the axial hydraulic force - a thermal barrier above the gear wheel. A hydrostatic bearing fitted to the exterior surround of the gear wheel, the gear shaft linkage is made by at least a centering and locating device having a cylindrical span and an axial stop and another independent device which can take up the torque [fr

Landing Gear Door Liners for Airframe Noise Reduction

Science.gov (United States)

Jones, Michael G. (Inventor); Howerton, Brian M. (Inventor); Van De Ven, Thomas (Inventor)

2014-01-01

A landing gear door for retractable landing gear of aircraft includes an acoustic liner. The acoustic liner includes one or more internal cavities or chambers having one or more openings that inhibit the generation of sound at the surface and/or absorb sound generated during operation of the aircraft. The landing gear door may include a plurality of internal chambers having different geometries to thereby absorb broadband noise.

Gear fault diagnosis based on the structured sparsity time-frequency analysis

Science.gov (United States)

Sun, Ruobin; Yang, Zhibo; Chen, Xuefeng; Tian, Shaohua; Xie, Yong

2018-03-01

Over the last decade, sparse representation has become a powerful paradigm in mechanical fault diagnosis due to its excellent capability and the high flexibility for complex signal description. The structured sparsity time-frequency analysis (SSTFA) is a novel signal processing method, which utilizes mixed-norm priors on time-frequency coefficients to obtain a fine match for the structure of signals. In order to extract the transient feature from gear vibration signals, a gear fault diagnosis method based on SSTFA is proposed in this work. The steady modulation components and impulsive components of the defective gear vibration signals can be extracted simultaneously by choosing different time-frequency neighborhood and generalized thresholding operators. Besides, the time-frequency distribution with high resolution is obtained by piling different components in the same diagram. The diagnostic conclusion can be made according to the envelope spectrum of the impulsive components or by the periodicity of impulses. The effectiveness of the method is verified by numerical simulations, and the vibration signals registered from a gearbox fault simulator and a wind turbine. To validate the efficiency of the presented methodology, comparisons are made among some state-of-the-art vibration separation methods and the traditional time-frequency analysis methods. The comparisons show that the proposed method possesses advantages in separating feature signals under strong noise and accounting for the inner time-frequency structure of the gear vibration signals.

50 CFR 635.21 - Gear operation and deployment restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Gear operation and deployment restrictions....21 Gear operation and deployment restrictions. Link to an amendment published at 75 FR 57701, Sept. 22, 2010. The green-stick gear authorization requirements under paragraphs (c)(2)(v)(A), (c)(2)(v)(B...

MODELING THE DOUBLE WORM-FACE GEARS

Directory of Open Access Journals (Sweden)

BOLOŞ Codruţa

2015-06-01

Full Text Available The worm-face gear family, invented 60 years ago, contains in its structure several variants which have the following defining elements: tapered worm, reverse tapered worm and cylindrical worm. This type of gear can be realized with a single wheel and also in engagement with the second embodiment of the front worm wheels. This paper presents the matrix - vectorial mathematical model of the double worm-face gear with cylindrical worm and a graphical modeling which is based on the specific geometrical characteristics accomplished by means of the Autodesk Inventor 3D modeling program. The applicability of the study, considering the solutions which it suggests, aims to create opportunities for the use of modern rapid prototyping and analysis of stress FEM technique.

Mixed movements/performance-based drawing

DEFF Research Database (Denmark)

Brabrand, Helle

2011-01-01

Mixed Movements is a research project engaged in performance-based architectural drawing. As one in a series working with architectonic implementation in relation to body and movements, the actual project relates body-movement and dynamic drawing and presents the material as interactive ‘space-time-tables’....

Experimental Research into Noise Emission of A Gear Micropump with Plastic Rotor

Science.gov (United States)

Rodionov, L. V.; Rekadze, P. D.

2018-01-01

The previous researches show that it’s possible to replace several parts of gear pump to plastic ones. This substitution leads to cost and noise reduction of the pump. Therefore, the series of acoustic experiments on a test bench were carry-out. Sound pressure levels were recorded with microphone, located in a pipe made of a vacuum rubber. Conducted experiment shows that acoustic characteristics of the micropump depend on the different material of driven rotor. Experimental result indicates that the proposed measures for replacing metal rotor to plastic one reduce micropump noise on the studied modes. The maximum achieved acoustic efficiency on equivalent level is 11 dB.

Multi-stage internal gear/turbine fuel pump

Energy Technology Data Exchange (ETDEWEB)

Maier, Eugen; Raney, Michael Raymond

2004-07-06

A multi-stage internal gear/turbine fuel pump for a vehicle includes a housing having an inlet and an outlet and a motor disposed in the housing. The multi-stage internal gear/turbine fuel pump also includes a shaft extending axially and disposed in the housing. The multi-stage internal gear/turbine fuel pump further includes a plurality of pumping modules disposed axially along the shaft. One of the pumping modules is a turbine pumping module and another of the pumping modules is a gerotor pumping module for rotation by the motor to pump fuel from the inlet to the outlet.

Three new models for evaluation of standard involute spur gear mesh stiffness

Science.gov (United States)

Liang, Xihui; Zhang, Hongsheng; Zuo, Ming J.; Qin, Yong

2018-02-01

Time-varying mesh stiffness is one of the main internal excitation sources of gear dynamics. Accurate evaluation of gear mesh stiffness is crucial for gear dynamic analysis. This study is devoted to developing new models for spur gear mesh stiffness evaluation. Three models are proposed. The proposed model 1 can give very accurate mesh stiffness result but the gear bore surface must be assumed to be rigid. Enlighted by the proposed model 1, our research discovers that the angular deflection pattern of the gear bore surface of a pair of meshing gears under a constant torque basically follows a cosine curve. Based on this finding, two other models are proposed. The proposed model 2 evaluates gear mesh stiffness by using angular deflections at different circumferential angles of an end surface circle of the gear bore. The proposed model 3 requires using only the angular deflection at an arbitrary circumferential angle of an end surface circle of the gear bore but this model can only be used for a gear with the same tooth profile among all teeth. The proposed models are accurate in gear mesh stiffness evaluation and easy to use. Finite element analysis is used to validate the accuracy of the proposed models.

Evaluation of Gear Condition Indicator Performance on Rotorcraft Fleet

Science.gov (United States)

Antolick, Lance J.; Branning, Jeremy S.; Wade, Daniel R.; Dempsey, Paula J.

2010-01-01

The U.S. Army is currently expanding its fleet of Health Usage Monitoring Systems (HUMS) equipped aircraft at significant rates, to now include over 1,000 rotorcraft. Two different on-board HUMS, the Honeywell Modern Signal Processing Unit (MSPU) and the Goodrich Integrated Vehicle Health Management System (IVHMS), are collecting vibration health data on aircraft that include the Apache, Blackhawk, Chinook, and Kiowa Warrior. The objective of this paper is to recommend the most effective gear condition indicators for fleet use based on both a theoretical foundation and field data. Gear diagnostics with better performance will be recommended based on both a theoretical foundation and results of in-fleet use. In order to evaluate the gear condition indicator performance on rotorcraft fleets, results of more than five years of health monitoring for gear faults in the entire HUMS equipped Army helicopter fleet will be presented. More than ten examples of gear faults indicated by the gear CI have been compiled and each reviewed for accuracy. False alarms indications will also be discussed. Performance data from test rigs and seeded fault tests will also be presented. The results of the fleet analysis will be discussed, and a performance metric assigned to each of the competing algorithms. Gear fault diagnostic algorithms that are compliant with ADS-79A will be recommended for future use and development. The performance of gear algorithms used in the commercial units and the effectiveness of the gear CI as a fault identifier will be assessed using the criteria outlined in the standards in ADS-79A-HDBK, an Army handbook that outlines the conversion from Reliability Centered Maintenance to the On-Condition status of Condition Based Maintenance.

The Strength Analysis of Differential Planetary Gears of Gearbox for Concrete Mixer Truck

Science.gov (United States)

Bae, M. H.; Bae, T. Y.; Kim, D. J.

2018-03-01

The power train of mixer gearbox for concrete mixer truck includes differential planetary gears to get large reduction ratio for operating mixer a drum and simple structure. The planetary gears are very important part of a mixer gearbox where strength problems namely gear bending stress, gear compressive stress and scoring failure are the main concern. In the present study, calculating specifications of the differential planetary gears and analyzing the gear bending and compressive stresses as well as scoring factor of the differential planetary gears gearbox for an optimal design of the mixer gearbox in respect to cost and reliability are investigated. The analyses of actual gear bending and compressive stresses of the differential planetary gears using Lewes & Hertz equation and verifications of the calculated specifications of the differential planetary gears evaluate the results with the data of allowable bending and compressive stress from the Stress-No. of cycles curves of gears. In addition, we also analyze actual gear scoring factor as well as evaluate the possibility of scoring failure of the differential planetary gear.

The design and analysis of single flank transmission error testor for loaded gears

Science.gov (United States)

Houser, D. R.; Bassett, D. E.

1985-01-01

Due to geometrical imperfections in gears and finite tooth stiffnesses, the motion transmitted from an input gear shaft to an output gear shaft will not have conjugate action. In order to strengthen the understanding of transmission error and to verify mathematical models of gear transmission error, a test stand that will measure the transmission error of a gear pair at operating loads, but at reduced speeds would be desirable. This document describes the design and development of a loaded transmission error tester. For a gear box with a gear ratio of one, few tooth meshing combinations will occur during a single test. In order to observe the effects of different tooth mesh combinations and to increase the ability to load test gear pairs with higher gear ratios, the system was designed around a gear box with a gear ratio of two.

50 CFR 660.319 - Open access fishery gear identification and marking.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Open access fishery gear identification... COAST STATES West Coast Groundfish-Open Access Fisheries § 660.319 Open access fishery gear identification and marking. (a) Gear identification. (1) Open access fixed gear (longline, trap or pot, set net...

Advanced Manufacture of Spiral Bevel and Hypoid Gears

Directory of Open Access Journals (Sweden)

Vilmos Simon

2016-11-01

Full Text Available In this study, an advanced method for the manufacture of spiral bevel and hypoid gears on CNC hypoid generators is proposed. The optmal head-cutter geometry and machine tool settings are determined to introduce the optimal tooth surface modifications into the teeth of spiral bevel and hypoid gears. The aim of these tooth surface modifications is to simultaneously reduce the tooth contact pressure and the transmission errors, to maximize the EHD load carrying capacity of the oil film, and to minimize power losses in the oil film. The proposed advanced method for the manufacture of spiral bevel and hypoid gears is based on machine tool setting variation on the cradle-type generator conducted by optimal polynomial functions and on the use of a CNC hypoid generator. An algorithm is developed for the execution of motions on the CNC hypoid generator using the optimal relations on the cradle-type machine. Effectiveness of the method was demonstrated by using spiral bevel and hypoid gear examples. Significant improvements in the operating characteristics of the gear pairs are achieved.

A New Model of the Fractional Order Dynamics of the Planetary Gears

Directory of Open Access Journals (Sweden)

Vera Nikolic-Stanojevic

2013-01-01

Full Text Available A theoretical model of planetary gears dynamics is presented. Planetary gears are parametrically excited by the time-varying mesh stiffness that fluctuates as the number of gear tooth pairs in contact changes during gear rotation. In the paper, it has been indicated that even the small disturbance in design realizations of this gear cause nonlinear properties of dynamics which are the source of vibrations and noise in the gear transmission. Dynamic model of the planetary gears with four degrees of freedom is used. Applying the basic principles of analytical mechanics and taking the initial and boundary conditions into consideration, it is possible to obtain the system of equations representing physical meshing process between the two or more gears. This investigation was focused to a new model of the fractional order dynamics of the planetary gear. For this model analytical expressions for the corresponding fractional order modes like one frequency eigen vibrational modes are obtained. For one planetary gear, eigen fractional modes are obtained, and a visualization is presented. By using MathCAD the solution is obtained.

Hardness and microstructure analysis of damaged gear caused by adhesive wear

Science.gov (United States)

Mahendra, Rizky Budi; Nugroho, Sri; Ismail, Rifky

2018-03-01

This study was a result from research on repairing project of damaged elevator gear box. The objective of this research is to analyze the failure part on elevator gearbox at flourmill factory. The equipment was damaged after one year installed and running on factory. Severe wear was occurred on high speed helical gear. These helical gear was one of main part of elevator gearbox in flour mill manufacture. Visually, plastic deformation didn't occurred and not visible on the failure helical gear shaft. Some test would be performed to check the chemical composition, microstructure and hardness of failure helical gear. The material of failure helical gear shaft was a medium carbon steel alloy. The microstructure was showed a martensitic phase formed on the surface to the center area of gear shaft. Otherwise, the depth of hardness layer slight formed on surface and lack depth of hardness layer was a main trigger of severe wear. It was not enough to resist wear due to friction caused by rolling and sliding on surface between high speed gear and low speed gear. Enhancement of hardness layer on surface and depth of hardness layer will make the component has more long life time. Furthermore, to perform next research is needed to analyze the reliability of enhanced hardness on layer and depth of hardness layer on helical gear shaft.

49 CFR 229.57 - Foundation brake gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Foundation brake gear. 229.57 Section 229.57 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Foundation brake gear. A lever, rod, brake beam, hanger, or pin may not be worn through more than 30 percent...

Torsional vibration signal analysis as a diagnostic tool for planetary gear fault detection

Science.gov (United States)

Xue, Song; Howard, Ian

2018-02-01

This paper aims to investigate the effectiveness of using the torsional vibration signal as a diagnostic tool for planetary gearbox faults detection. The traditional approach for condition monitoring of the planetary gear uses a stationary transducer mounted on the ring gear casing to measure all the vibration data when the planet gears pass by with the rotation of the carrier arm. However, the time variant vibration transfer paths between the stationary transducer and the rotating planet gear modulate the resultant vibration spectra and make it complex. Torsional vibration signals are theoretically free from this modulation effect and therefore, it is expected to be much easier and more effective to diagnose planetary gear faults using the fault diagnostic information extracted from the torsional vibration. In this paper, a 20 degree of freedom planetary gear lumped-parameter model was developed to obtain the gear dynamic response. In the model, the gear mesh stiffness variations are the main internal vibration generation mechanism and the finite element models were developed for calculation of the sun-planet and ring-planet gear mesh stiffnesses. Gear faults on different components were created in the finite element models to calculate the resultant gear mesh stiffnesses, which were incorporated into the planetary gear model later on to obtain the faulted vibration signal. Some advanced signal processing techniques were utilized to analyses the fault diagnostic results from the torsional vibration. It was found that the planetary gear torsional vibration not only successfully detected the gear fault, but also had the potential to indicate the location of the gear fault. As a result, the planetary gear torsional vibration can be considered an effective alternative approach for planetary gear condition monitoring.

Electrostatic microactuators with integrated gear linkages for mechanical power transmission

NARCIS (Netherlands)

Legtenberg, R.; Legtenberg, Rob; Berenschot, Johan W.; Elwenspoek, Michael Curt; Fluitman, J.H.J.

1996-01-01

In this paper a surface micromachining process is presented which has been used to fabricate electrostatic microactuators that are interconnected with each other and linked to other movable microstructures by integrated gear linkages. The gear linkages consist of rotational and linear gear

An Application of Reverse Engineering in Design of the Spur Gear

Directory of Open Access Journals (Sweden)

Adem Çiçek

2010-06-01

Full Text Available In this study, it is aimed that the gear parameters required the design of a spur gear are obtained by use of reverse engineering techniques. Therefore, point cloud of tooth profile of the manufactured spur gear is extracted by a coordinate measuring machine (CMM. The gear parameters are derived by processing the obtained point cloud. 3D model of the spur gear are modeled through this parameters in a CAD environment. In the system, a hybrid programming approach is used. Generating and processing the point cloud, extraction of the gear parameters are performed by Visual BASIC programming language. 3D modeling in the CAD environment is performed also by AutoLISP programming language due to programming simplicity. These two softwares are provided to be in harmony by integrating them. In the study, SolidworksTM and AutoCADTM are selected as CAD environments. With this study, an alternative approach for the design of the spur gear is presented and modeling of the gears in the CAD environment is carried out using reverse engineering techniques.

Mathematical Modelling of Involute Spur Gears Manufactured by Rack Cutter

Directory of Open Access Journals (Sweden)

Tufan Gürkan YILMAZ

2016-05-01

Full Text Available In this study, mathematical modelling of asymmetric involute spur gears was situated in by Litvin approach. In this context, firstly, mathematical expressions of rack cutter which manufacture asymmetric involute spur gear, then mathematical expression of asymmetric involute spur gear were obtained by using differential geometry, coordinate transformation and gear theory. Mathematical expressions were modelled in MATLAB and output files including points of involute spur gear’s teeth were designed automatically thanks to macros.

Generation of gear tooth surfaces by application of CNC machines

Science.gov (United States)

Litvin, F. L.; Chen, N. X.

1994-01-01

This study will demonstrate the importance of application of computer numerically controlled (CNC) machines in generation of gear tooth surfaces with new topology. This topology decreases gear vibration and will extend the gear capacity and service life. A preliminary investigation by a tooth contact analysis (TCA) program has shown that gear tooth surfaces in line contact (for instance, involute helical gears with parallel axes, worm gear drives with cylindrical worms, etc.) are very sensitive to angular errors of misalignment that cause edge contact and an unfavorable shape of transmission errors and vibration. The new topology of gear tooth surfaces is based on the localization of bearing contact, and the synthesis of a predesigned parabolic function of transmission errors that is able to absorb a piecewise linear function of transmission errors caused by gear misalignment. The report will describe the following topics: description of kinematics of CNC machines with six degrees of freedom that can be applied for generation of gear tooth surfaces with new topology. A new method for grinding of gear tooth surfaces by a cone surface or surface of revolution based on application of CNC machines is described. This method provides an optimal approximation of the ground surface to the given one. This method is especially beneficial when undeveloped ruled surfaces are to be ground. Execution of motions of the CNC machine is also described. The solution to this problem can be applied as well for the transfer of machine tool settings from a conventional generator to the CNC machine. The developed theory required the derivation of a modified equation of meshing based on application of the concept of space curves, space curves represented on surfaces, geodesic curvature, surface torsion, etc. Condensed information on these topics of differential geometry is provided as well.

50 CFR Table 19 to Part 679 - Seabird Avoidance Gear Codes

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 9 2010-10-01 2010-10-01 false Seabird Avoidance Gear Codes 19 Table 19... ALASKA Pt. 679, Table 19 Table 19 to Part 679—Seabird Avoidance Gear Codes VESSEL LOGBOOK CODE SEABIRD AVOIDANCE GEAR OR METHOD. 1 Paired Streamer Lines: Used during deployment of hook-and-line gear to prevent...

Continued Evaluation of Gear Condition Indicator Performance on Rotorcraft Fleet

Science.gov (United States)

Delgado, Irebert R.; Dempsey, Paula J.; Antolick, Lance J.; Wade, Daniel R.

2013-01-01

This paper details analyses of condition indicator performance for the helicopter nose gearbox within the U.S. Army's Condition-Based Maintenance Program. Ten nose gearbox data sets underwent two specific analyses. A mean condition indicator level analysis was performed where condition indicator performance was based on a 'batting average' measured before and after part replacement. Two specific condition indicators, Diagnostic Algorithm 1 and Sideband Index, were found to perform well for the data sets studied. A condition indicator versus gear wear analysis was also performed, where gear wear photographs and descriptions from Army tear-down analyses were categorized based on ANSI/AGMA 1010-E95 standards. Seven nose gearbox data sets were analyzed and correlated with condition indicators Diagnostic Algorithm 1 and Sideband Index. Both were found to be most responsive to gear wear cases of micropitting and spalling. Input pinion nose gear box condition indicators were found to be more responsive to part replacement during overhaul than their corresponding output gear nose gear box condition indicators.

Analysis and Compensation for Gear Accuracy with Setting Error in Form Grinding

Directory of Open Access Journals (Sweden)

Chenggang Fang

2015-01-01

Full Text Available In the process of form grinding, gear setting error was the main factor that influenced the form grinding accuracy; we proposed an effective method to improve form grinding accuracy that corrected the error by controlling the machine operations. Based on establishing the geometry model of form grinding and representing the gear setting errors as homogeneous coordinate, tooth mathematic model was obtained and simplified under the gear setting error. Then, according to the gear standard of ISO1328-1: 1997 and the ANSI/AGMA 2015-1-A01: 2002, the relationship was investigated by changing the gear setting errors with respect to tooth profile deviation, helix deviation, and cumulative pitch deviation, respectively, under the condition of gear eccentricity error, gear inclination error, and gear resultant error. An error compensation method was proposed based on solving sensitivity coefficient matrix of setting error in a five-axis CNC form grinding machine; simulation and experimental results demonstrated that the method can effectively correct the gear setting error, as well as further improving the forming grinding accuracy.

The Absolute Deviation Rank Diagnostic Approach to Gear Tooth Composite Fault

Directory of Open Access Journals (Sweden)

Guangbin Wang

2017-01-01

Full Text Available Aiming at nonlinear and nonstationary characteristics of the different degree with single fault gear tooth broken, pitting, and composite fault gear tooth broken-pitting, a method for the diagnosis of absolute deviation of gear faults is presented. The method uses ADAMS, respectively, set-up dynamics model of single fault gear tooth broken, pitting, and composite fault gear tooth broken-pitting, to obtain the result of different degree of broken teeth, pitting the single fault and compound faults in the meshing frequency, and the amplitude frequency doubling through simulating analysis. Through the comparison with the normal state to obtain the sensitive characteristic of the fault, the absolute value deviation diagnostic approach is used to identify the fault and validate it through experiments. The results show that absolute deviation rank diagnostic approach can realize the recognition of gear single faults and compound faults with different degrees and provide quick reference to determine the degree of gear fault.

Numerical Simulation of Oil Jet Lubrication for High Speed Gears

Directory of Open Access Journals (Sweden)

Tommaso Fondelli

2015-01-01

Full Text Available The Geared Turbofan technology is one of the most promising engine configurations to significantly reduce the specific fuel consumption. In this architecture, a power epicyclical gearbox is interposed between the fan and the low pressure spool. Thanks to the gearbox, fan and low pressure spool can turn at different speed, leading to higher engine bypass ratio. Therefore the gearbox efficiency becomes a key parameter for such technology. Further improvement of efficiency can be achieved developing a physical understanding of fluid dynamic losses within the transmission system. These losses are mainly related to viscous effects and they are directly connected to the lubrication method. In this work, the oil injection losses have been studied by means of CFD simulations. A numerical study of a single oil jet impinging on a single high speed gear has been carried out using the VOF method. The aim of this analysis is to evaluate the resistant torque due to the oil jet lubrication, correlating the torque data with the oil-gear interaction phases. URANS calculations have been performed using an adaptive meshing approach, as a way of significantly reducing the simulation costs. A global sensitivity analysis of adopted models has been carried out and a numerical setup has been defined.

Natural Characteristics of The Herringbone Gear Transmission System

Science.gov (United States)

Zhou, Jianxing; Sun, Wenlei; Cao, Li

2018-03-01

According to the structure characteristics of herringbone gear transmission, a more realistic dynamic model of the transmission system is built in consideration of the inner excitation, herringbone gears axial positioning and sliding bearing etc. The natural frequencies of the system are calculated, and the vibration mode is divided into symmetric vibration modes and asymmetric vibration modes. The time history of system dynamic force is obtained by solving the dynamic model. The effects of the connection stiffness of left and right sides of herringbone gears and axial support stiffness on natural characteristics are discussed.

Potential for Landing Gear Noise Reduction on Advanced Aircraft Configurations

Science.gov (United States)

Thomas, Russell H.; Nickol, Craig L.; Burley, Casey L.; Guo, Yueping

2016-01-01

The potential of significantly reducing aircraft landing gear noise is explored for aircraft configurations with engines installed above the wings or the fuselage. An innovative concept is studied that does not alter the main gear assembly itself but does shorten the main strut and integrates the gear in pods whose interior surfaces are treated with acoustic liner. The concept is meant to achieve maximum noise reduction so that main landing gears can be eliminated as a major source of airframe noise. By applying this concept to an aircraft configuration with 2025 entry-into-service technology levels, it is shown that compared to noise levels of current technology, the main gear noise can be reduced by 10 EPNL dB, bringing the main gear noise close to a floor established by other components such as the nose gear. The assessment of the noise reduction potential accounts for design features for the advanced aircraft configuration and includes the effects of local flow velocity in and around the pods, gear noise reflection from the airframe, and reflection and attenuation from acoustic liner treatment on pod surfaces and doors. A technical roadmap for maturing this concept is discussed, and the possible drag increase at cruise due to the addition of the pods is identified as a challenge, which needs to be quantified and minimized possibly with the combination of detailed design and application of drag reduction technologies.

Influence of material and gear parameters on the safety of gearing in metallurgical industry

Directory of Open Access Journals (Sweden)

S. Medvecká - Beňová

2015-01-01

Full Text Available This paper deals with the appropriate choice of parameters to obtain the desired level of safety of gears in a gearbox to drive the conveyor in the metallurgical industry under increased load. Steel with surface hardness up to 350 HBW, or heat treated steel with hardness of 500 - 650 HBW are used. As a final heat treatment are used surface hardening, cementation and hardening, nitridation. Good properties of heat-treated steels are at the correct thickness of the heat-treated layer of the tooth. Results are presented for dual-ratio gearbox with spur gears from operation of an integrated steel company.

JaxoDraw: A graphical user interface for drawing Feynman diagrams

Science.gov (United States)

Binosi, D.; Theußl, L.

2004-08-01

JaxoDraw is a Feynman graph plotting tool written in Java. It has a complete graphical user interface that allows all actions to be carried out via mouse click-and-drag operations in a WYSIWYG fashion. Graphs may be exported to postscript/EPS format and can be saved in XML files to be used for later sessions. One of JaxoDraw's main features is the possibility to create ? code that may be used to generate graphics output, thus combining the powers of ? with those of a modern day drawing program. With JaxoDraw it becomes possible to draw even complicated Feynman diagrams with just a few mouse clicks, without the knowledge of any programming language. Program summaryTitle of program: JaxoDraw Catalogue identifier: ADUA Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADUA Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar gzip file Operating system: Any Java-enabled platform, tested on Linux, Windows ME, XP, Mac OS X Programming language used: Java License: GPL Nature of problem: Existing methods for drawing Feynman diagrams usually require some 'hard-coding' in one or the other programming or scripting language. It is not very convenient and often time consuming, to generate relatively simple diagrams. Method of solution: A program is provided that allows for the interactive drawing of Feynman diagrams with a graphical user interface. The program is easy to learn and use, produces high quality output in several formats and runs on any operating system where a Java Runtime Environment is available. Number of bytes in distributed program, including test data: 2 117 863 Number of lines in distributed program, including test data: 60 000 Restrictions: Certain operations (like internal latex compilation, Postscript preview) require the execution of external commands that might not work on untested operating systems. Typical running time: As an interactive program, the running time depends on the complexity

Research on vibration signal analysis and extraction method of gear local fault

Science.gov (United States)

Yang, X. F.; Wang, D.; Ma, J. F.; Shao, W.

2018-02-01

Gear is the main connection parts and power transmission parts in the mechanical equipment. If the fault occurs, it directly affects the running state of the whole machine and even endangers the personal safety. So it has important theoretical significance and practical value to study on the extraction of the gear fault signal and fault diagnosis of the gear. In this paper, the gear local fault as the research object, set up the vibration model of gear fault vibration mechanism, derive the vibration mechanism of the gear local fault and analyzes the similarities and differences of the vibration signal between the gear non fault and the gears local faults. In the MATLAB environment, the wavelet transform algorithm is used to denoise the fault signal. Hilbert transform is used to demodulate the fault vibration signal. The results show that the method can denoise the strong noise mechanical vibration signal and extract the local fault feature information from the fault vibration signal..

Drawing evaluation report for sampling equipment drawings

International Nuclear Information System (INIS)

WILSON, G.W.

1999-01-01

This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999

46 CFR 78.47-55 - Instructions for changing steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Instructions for changing steering gear. 78.47-55... OPERATIONS Markings for Fire and Emergency Equipment, Etc. § 78.47-55 Instructions for changing steering gear..., relating in order, the different steps to be taken in changing to the emergency steering gear. Each clutch...

Co-Constructing Knowledge through NGO-Driven Circle Work

DEFF Research Database (Denmark)

Agerbæk, Jonas

This presentation revolves around the question of what degree of control, if any, the users participating in NGO-driven development programs may have over their own development. Based on a multi-sited ethnography of NGO organizing and communication that I conducted in the period of 2010 to 2015......, and with a special analytical focus on the facilitating role of frontline NGO workers in rural East Africa, this presentation discusses enabling and constraining aspects of using circle work to co-produce knowledge in international development. More particularly I am focusing an approach to circle work called......, then participatory approaches such as REFLECT can be used not only to drive changes locally but also bolster the global participatory agenda of defining development practices and politics from the bottom and up...

Study of a spur gear dynamic behavior in transient regime

Science.gov (United States)

Khabou, M. T.; Bouchaala, N.; Chaari, F.; Fakhfakh, T.; Haddar, M.

2011-11-01

In this paper the dynamic behavior of a single stage spur gear reducer in transient regime is studied. Dynamic response of the single stage spur gear reducer is investigated at different rotating velocities. First, gear excitation is induced by the motor torque and load variation in addition to the fluctuation of meshing stiffness due to the variation of input rotational speed. Then, the dynamic response is computed using the Newmark method. After that, a parameter study is made on spur gear powered in the first place by an electric motor and in the second place by four strokes four cylinders diesel engine. Dynamic responses come to confirm a significant influence of the transient regime on the dynamic behavior of a gear set, particularly in the case of engine acyclism condition.

46 CFR 196.37-33 - Instructions for changing steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Instructions for changing steering gear. 196.37-33... steering gear. (a) Instructions in at least 1/2 inch letters and figures shall be posted in the steering engineroom, relating in order, the different steps to be taken in changing to the emergency steering gear...

Recent development work on PIM: a Blumlein driven IVA machine

International Nuclear Information System (INIS)

Phillips, Martin J.; Sinclair, Mark A.; Williamson, Mark C.; Clough, Stephen G.; Thomas, Kenneth J.; Smith, Ian Douglas; Bailey, Vernon Leslie; Johnson, David Lee; Corcoran, Patrick Allen; Kishi, Hiroshi J.; Maenchen, John Eric

2003-01-01

An IVA (inductive voltage adder) research programme at AWE began with the construction of a small scale IVA test bed named LINX and progressed to building PIM (Prototype IVA Module). The work on PIM is geared towards furnishing AWE with a range of machines operating at 1 to 4 MV that may eventually supersede, with an upgrade in performance, existing machines operating in that voltage range. PIM has a water dielectric Blumlein of 10 ohms charged by a Marx generator. This has been used to drive either one or two 1.5 MV inductive cavities and fitting a third cavity may be attempted in the future. The latest two cavity configuration is shown which requires a split oil coax to connect the two cavities in parallel. It also has a laser triggering system for initiating the Blumlein and the prepulse reduction system fitted to the output of the Blumlein. A short MITL (magnetically insulated transmission line) connects the cavities, via a vacuum pumping section, to a chamber containing an e-beam diode test load.

Demonstrations of bio-inspired perching landing gear for UAVs

Science.gov (United States)

Tieu, Mindy; Michael, Duncan M.; Pflueger, Jeffery B.; Sethi, Manik S.; Shimazu, Kelli N.; Anthony, Tatiana M.; Lee, Christopher L.

2016-04-01

Results are presented which demonstrate the feasibility and performance of two concepts of biologically-inspired landing-gear systems that enable bird-sized, unmanned aerial vehicles (UAV's) to land, perch, and take-off from branchlike structures and/or ledges. The first concept follows the anatomy of birds that can grasp ahold of a branch and perch as tendons in their legs are tensioned. This design involves a gravity-activated, cable-driven, underactuated, graspingfoot mechanism. As the UAV lands, its weight collapses a four-bar linkage pulling a cable which curls two opposing, multi-segmented feet to grasp the landing target. Each foot is a single, compliant mechanism fabricated by simultaneouly 3D-printing a flexible thermo-plastic and a stiffer ABS plastic. The design is optimized to grasp structures over a range of shapes and sizes. Quasi-static and flight tests of this landing gear affixed to RC rotorcraft (24 cm to 550 cm in diameter) demonstrate that the aircraft can land, perch, and take-off from a tree branch, rectangular wood board, PVC pipe, metal hand rail, chair armrest, and in addition, a stone wall ledge. Stability tests show that perching is maintained under base and wind disturbances. The second design concept, inspired by roosting bats, is a two-material, 3D-printed hooking mechanism that enables the UAV to stably suspend itself from a wire or small-diameter branch. The design balances structural stiffness for support and flexibility for the perching process. A flight-test demonstrates the attaching and dis-engaging of a small, RC quadcopter from a suspended line.

Work(er)-Driven Innovation

Science.gov (United States)

Smith, Raymond

2017-01-01

Purpose: The focus on innovation as a foundational element of enhanced organisational performance has led to the promoting and valuing of greater levels of employee participation in innovation processes. An emergent concept of employee-driven innovation could be argued to have hindered understandings of the creative and transformative nature of…

Survey gear calibration independent of spatial fish distribution

DEFF Research Database (Denmark)

Lewy, Peter; Nielsen, J. Rasmus; Hovgård, Holger

2004-01-01

Trawl surveys provide important information for evaluation of relative stock abundance fluctuations over time. Therefore, when survey gears or vessels are changed, it is important to compare the efficiency and selectivity of old and new gears and vessels. A method for estimation of conversion fac...

Technology Innovation of Power Transmission Gearing in Aviation

Science.gov (United States)

Handschuh, Robert F.

2009-01-01

An overview of rotary wing evolution and innovations over the last 20 years was presented. This overview is provided from a drive system perspective. Examples of technology innovations that have changed and advanced drive systems of rotary wing vehicles will be provided. These innovations include full 6-axis CNC gear manufacture, face gear development to aerospace standards, health and usage monitoring, and gear geometry and bearing improvements. Also, an overview of current state-of-the-art activities being conducted at NASA Glenn is presented with a short look to fixed and rotary wing aircraft and systems needed for the future.

Experiences of how fishers grab opportunities in (more) free regulation of gear

DEFF Research Database (Denmark)

Qvist Eliasen, Søren; Mortensen, Lars O.; Ulrich, Clara

In the Minidisc project 14 vessels fished under conditions corresponding to free choose of gear. Based on the skippers initial idea of gear adjustment and a subsequent interview 6 months later the experiences of the skippers´ choice of “free” gear, the process for adjusting it and the tools...... for evaluating the efficiency and selectivity are discussed. Only incremental development using elements from previous used gear and other fisheries were found. Gear development took place in an interaction between the skipper and trawl maker, while no research was involved. This indicates that free choice...... of gear (under monitored discard ban) would lead to incremental adjustments. Parts of the fleet would have difficulties in evaluating the gear and subsequently optimise by adjusting. This would leave a need for support for development of evaluation procedures, especially among the small vessels. Radical...

Stress analyses of pump gears produced by powder metallurgy

Energy Technology Data Exchange (ETDEWEB)

Cetinel, Hakan [Celal Bayar Univ., Mechanical Engineering Dept. (Turkey); Yilmaz, Burak

2013-06-01

In this study, trochoidal type (gerotor) hydraulic pump gears were produced by powder metallurgy (P/M) technique. Several gears with different mechanical properties have been obtained by changing process variables. The tooth contact stresses were calculated analytically under particular operation conditions of the hydraulic pump. The 3D models have been obtained from real gears by using Capability Maturity Model (CMM, 3D scanning) operation and SOLIDWORKS software. Stress analyses were conducted on these 3D models by using ANSYS WORKBENCH software. It was found that the density increases by the increase of sintering duration and mechanical properties were positively affected by the increase of density. Maximum deformation takes place in the region of the outer gear where failure generally occurs with the minimum cross-section area.

Toothed gear pumps for special applications; Zahnradpumpen fuer Sonderanwendungen

Energy Technology Data Exchange (ETDEWEB)

Kremer, H. [WITTE PUMPS und TECHNOLOGY GmbH, Uetersen (Germany)

2007-07-01

Gear pumps are utilized in a big variety of industrial processes. This essay discusses the typical applications gear pumps are used for. Based on the general function of gear pumps the technical features of these different pump types are pointed out. The process parameters have been more or less the same for the last decades. Nowadays a higher demand regarding pressures and temperatures, sometimes even a combination of both, can be observed. This development is the challenge to go for special constructions and new materials. The range of applications is extended step by step, always aware of the fact, that these gear pumps are often operating at their specific limits. Finally some examples right from the plant give an overview over this development. (orig.)

Instrumentation and test gear circuits manual

CERN Document Server

Marston, R M

2013-01-01

Instrumentation and Test Gear Circuits Manual provides diagrams, graphs, tables, and discussions of several types of practical circuits. The practical circuits covered in this book include attenuators, bridges, scope trace doublers, timebases, and digital frequency meters. Chapter 1 discusses the basic instrumentation and test gear principles. Chapter 2 deals with the design of passive attenuators, and Chapter 3 with passive and active filter circuits. The subsequent chapters tackle 'bridge' circuits, analogue and digital metering techniques and circuitry, signal and waveform generation, and p

Induction Hardening of External Gear

Science.gov (United States)

Bukanin, V. A.; Ivanov, A. N.; Zenkov, A. E.; Vologdin, V. V.; Vologdin, V. V., Jr.

2018-03-01

Problems and solution of gear induction hardening are described. Main attention is paid to the parameters of heating and cooling systems. ELTA 7.0 program has been used to obtain the required electrical parameters of inductor, power sources, resonant circuits, as well as to choose the quenching media. Comparison of experimental and calculated results of investigation is provided. In order to compare advantages and disadvantages of single- and dual-frequency heating processes, many variants of these technologies were simulated. The predicted structure and hardness of steel gears are obtained by use of the ELTA data base taken into account the Continuous Cooling Transformation diagrams.

Darwin-industrien i højt gear

DEFF Research Database (Denmark)

Kjærgaard, Peter C.

2008-01-01

Darwin-industrien i højt gear. Næste år bliver et 'Darwin-år' - både tilhængere og kritikere gør sig klar. Udgivelsesdato: 12. december......Darwin-industrien i højt gear. Næste år bliver et 'Darwin-år' - både tilhængere og kritikere gør sig klar. Udgivelsesdato: 12. december...

Teaching Planetary Gear Trains with the Aid of Nomographs

Directory of Open Access Journals (Sweden)

Essam Lauibi Esmail

2013-01-01

Full Text Available Planetary gear trains (PGTs are introduced to undergraduate mechanical engineering students in the course of Theory of Machines. The complexity of the traditional methods for analyzing PGTs has kept many from becoming familiar with the capability of PGTs in mechanisms and machine design. In this paper a unified general formulation for simultaneously visualizing velocities, torques, and power flow through a train is presented on a single nomograph. Therefore, the increasing complex mechanical systems, such as automotive transmissions, are much easier to understand. Nomographs of Fundamental Gear Entities (FGEs are constructed based on the nomographs of their fundamental circuits, without specifying the exact gear dimensions. They are then unified in one system nomograph. Nomographs are promising to provide designers with an efficient tool for the design of geared mechanisms.

Characteristics study of the gears by the CAD/CAE

Science.gov (United States)

Wang, P. Y.; Chang, S. L.; Lee, B. Y.; Nguyen, D. H.; Cao, C. W.

2017-09-01

Gears are the most important transmission component in machines. The rapid development of the machines in industry requires a shorter time of the analysis process. In traditional, the gears are analyzed by setting up the complete mathematical model firstly, considering the profile of cutter and coordinate systems relationship between the machine and the cutter. It is a really complex and time-consuming process. Recently, the CAD/CAE software is well developed and useful in the mechanical design. In this paper, the Autodesk Inventor® software is introduced to model the spherical gears firstly, and then the models can also be transferred into ANSYS Workbench for the finite element analysis. The proposed process in this paper is helpful to the engineers to speed up the analyzing process of gears in the design stage.

Sizing Optimization and Strength Analysis for Spread-type Gear Reducers

Directory of Open Access Journals (Sweden)

Wei-Hsuan Hsu

2014-08-01

Full Text Available A reducer is now developed towards the trend of customization service and cost-saving. In this study, a sizing program for the reducer has been developed in order to replace the manual sizing process. We aim at the total center distance of the gear reducer for optimization to reduce gear volume and weight. Also, we checked constrains such as, tooth root bending, tooth contact strength, gear shaft endangered cross-section, bearing life, gear shaft deflection, and torsion angle deformation, etc., to obtain reliable drive strength. Comparisons of sizes and weights before and after optimization confirm that the purpose for reducing production cost is achieved.

Natural Frequencies and Vibrating Modes for a Magnetic Planetary Gear Drive

Directory of Open Access Journals (Sweden)

Lizhong Xu

2012-01-01

Full Text Available In this paper, a dynamic model for a magnetic planetary gear drive is proposed. Based on the model, the dynamic equations for the magnetic planetary gear drive are given. From the magnetic meshing forces and torques between the elements for the drive system, the tangent and radial magnetic meshing stiffness is obtained. Using these equations, the natural frequencies and the modes of the magnetic planetary gear drive are investigated. The sensitivity of the natural frequencies to the system parameters is discussed. Results show that the pole pair number and the air gap have obvious effects on the natural frequencies. For the planetary gear number larger than two, the vibrations of the drive system include the torsion mode of the center elements, the translation mode of the center elements, and the planet modes. For the planetary gear number equal to two, the planet mode does not occur, the crown mode and the sun gear mode occur.

Drawing experts have better visual memory while drawing.

Science.gov (United States)

Perdreau, Florian; Cavanagh, Patrick

2015-01-01

Drawing involves frequent shifts of gaze between the original and the drawing and visual memory helps compare the original object and the drawing across these gaze shifts while creating and correcting the drawing. It remains unclear whether this memory encodes all of the object or only the features around the current drawing position and whether both the original and the copy are equally well represented. To address these questions, we designed a "drawing" experiment coupled with a change detection task. A polygon was displayed on one screen and participants had to copy it on another, with the original and the drawing presented in alternation. At unpredictable moments during the copying process, modifications were made on the drawing and the original figure (while they were not in view). Participants had to correct their drawing every time they perceived a change so that their drawing always matched the current original figure. Our results show a better memory representation of the original figure than of the drawing, with locations relevant to the current production most accurately represented. Critically, experts showed better memory for both the original and the drawing than did novices, suggesting that experts have specialized advantages for encoding visual shapes.

Unilateral maxillary molar distalization with zygoma-gear appliance.

Science.gov (United States)

Kilkis, Dogan; Bayram, Mehmet; Celikoglu, Mevlut; Nur, Metin

2012-08-01

The aim of this study was to present the orthodontic treatment of a 15-year-old boy with a unilateral maxillary molar distalization system, called the zygoma-gear appliance. It consisted of a zygomatic anchorage miniplate, an inner bow, and a Sentalloy closed coil spring (GAC International, Bohemia, NY). A distalizing force of 350 g was used during the distalization period. The unilateral Class II malocclusion was corrected in 5 months with the zygoma-gear appliance. The maxillary left first molar showed distalization of 4 mm with an inclination of 3°. The maxillary premolars moved distally with the help of the transseptal fibers. In addition, there were slight decreases in overjet (-0.5 mm) and maxillary incisor inclination (-1°), indicating no anchorage loss from the zygoma-gear appliance. Preadjusted fixed appliances (0.022 × 0.028-in, MBT system; 3M Unitek, Monrovia, Calif) were placed in both arches to achieve leveling and alignment. After 14 months of unilateral distalization with the zygoma-gear appliance and fixed appliances, Class I molar and canine relationships were established with satisfactory interdigitation of the posterior teeth. Acceptable overjet and overbite were also achieved. This article shows that this new system, the zygoma-gear appliance, can be used for unilateral maxillary molar distalization without anchorage loss. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Walking the Torque: Proposed Work Plan for Energy-Efficiency Policy Opportunities for Electric Motor-Driven Systems

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

Electric motor-driven system is the largest single energy end use accounting for more than 40% of global electricity consumption. This paper sets out an ambitious but achievable target with the global work plan to improve the energy efficiency of electric motor-driven system by 10% to 15% based on the finding of working paper ''Energy-Efficiency Policy Opportunities for Electric Motor-Driven Systems (Waide et al., 2011)''. If governments commit to the proposed work plan immediately and maintain resourcing levels, this could be achieved by 2030 and it would be equivalent to reducing total global electricity use by around 5%. The proposed work plan of this paper is to align regulatory settings within a globally applicable scheme. The IEA believes this target can only be achieved through global co-operation leading to aligned national policy settings that countries can unlock the economies of scale that will result from using more energy efficient EMDS.

Analisa Kekuatan Spiral Bevel Gear Dengan Variasi Sudut Spiral Menggunakan Metode Elemen Hingga

OpenAIRE

Deta Rachmat Andika; Agus Sigit Pramono

2017-01-01

Seiring perkembangan zaman,  teknologi roda gigi dituntut untuk mampu mentransmisikan daya yang besar dengan efisiensi yang besar pula. Pada jenis intersecting shaft gear, tipe roda gigi payung spiral (spiral bevel gear)  merupakan perkembangan dari roda gigi payung bergigi lurus (straight bevel gear). Kelebihan dari spiral bevel gear antara  lain adalah kemampuan transmisi daya dan efisiensi yang lebih besar pada geometri yang sama serta tidak terlalu berisik. Akan tetapi spiral bevel gear j...

Research of HCR Gearing Properties from Warm Scuffing Damage Point of View

Directory of Open Access Journals (Sweden)

Kuzmanović Siniša

2014-12-01

Full Text Available The issue of design and dimensioning of HCR gearing, particularly of the gearings with an internal engagement, it nowadays, especially in the design of hybrid cars drives, highly topical. This kind of gearing has many advantages in operation, but at the same time it is more complicated in stage of its design and load capacity calculation. Authors in this contribution present some results of temperature scuffing research of internal and external HCR gearing. There are given the equations for calculation of warm scuffing resistance of both external and internal HCR gearing derived according to the integral temperature criterion.

Gear Mesh Loss-of-Lubrication Experiments and Analytical Simulation

Science.gov (United States)

Handschuh, Robert F.; Polly, Joseph; Morales, Wilfredo

2011-01-01

An experimental program to determine the loss-of-lubrication (LOL) characteristics of spur gears in an aerospace simulation test facility has been completed. Tests were conducted using two different emergency lubricant types: (1) an oil mist system (two different misted lubricants) and (2) a grease injection system (two different grease types). Tests were conducted using a NASA Glenn test facility normally used for conducting contact fatigue. Tests were run at rotational speeds up to 10000 rpm using two different gear designs and two different gear materials. For the tests conducted using an air-oil misting system, a minimum lubricant injection rate was determined to permit the gear mesh to operate without failure for at least 1 hr. The tests allowed an elevated steady state temperature to be established. A basic 2-D heat transfer simulation has been developed to investigate temperatures of a simulated gear as a function of frictional behavior. The friction (heat generation source) between the meshing surfaces is related to the position in the meshing cycle, the load applied, and the amount of lubricant in the contact. Experimental conditions will be compared to those from the 2-D simulation.

GEAR: A database of Genomic Elements Associated with drug Resistance

Science.gov (United States)

Wang, Yin-Ying; Chen, Wei-Hua; Xiao, Pei-Pei; Xie, Wen-Bin; Luo, Qibin; Bork, Peer; Zhao, Xing-Ming

2017-01-01

Drug resistance is becoming a serious problem that leads to the failure of standard treatments, which is generally developed because of genetic mutations of certain molecules. Here, we present GEAR (A database of Genomic Elements Associated with drug Resistance) that aims to provide comprehensive information about genomic elements (including genes, single-nucleotide polymorphisms and microRNAs) that are responsible for drug resistance. Right now, GEAR contains 1631 associations between 201 human drugs and 758 genes, 106 associations between 29 human drugs and 66 miRNAs, and 44 associations between 17 human drugs and 22 SNPs. These relationships are firstly extracted from primary literature with text mining and then manually curated. The drug resistome deposited in GEAR provides insights into the genetic factors underlying drug resistance. In addition, new indications and potential drug combinations can be identified based on the resistome. The GEAR database can be freely accessed through http://gear.comp-sysbio.org. PMID:28294141

Drawing evaluation report for sampling equipment drawings; TOPICAL

International Nuclear Information System (INIS)

WILSON, G.W.

1999-01-01

This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999

Modeling of Two-Wheeled Self-Balancing Robot Driven by DC Gearmotors

Science.gov (United States)

Frankovský, P.; Dominik, L.; Gmiterko, A.; Virgala, I.; Kurylo, P.; Perminova, O.

2017-08-01

This paper is aimed at modelling a two-wheeled self-balancing robot driven by the geared DC motors. A mathematical model consists of two main parts, the model of robot's mechanical structure and the model of the actuator. Linearized equations of motion are derived and the overall model of the two-wheeled self-balancing robot is represented in state-space realization for the purpose of state feedback controller design.

A MATHEMATICAL MODEL OF CHP 2000 TYPE PROGRESSIVE GEAR

Directory of Open Access Journals (Sweden)

Paweł Lonkwic

2016-12-01

Full Text Available The project of CHP2000 type progressive gear has been presented in the article. The offered solution from its construction point of view differs from the existing solutions due to the application of Belleville springs packets supporting the braking roller cam and achieving a flexible range of the gear loading. The standard concept of the gear loading within a mathematical and a geometrical model has been presented in the article. The proposed solution can be used in the friction lifts with the loading capacity from 8500 up to 20000 N.

Coefficient of friction of a starved lubricated spur gear pair

International Nuclear Information System (INIS)

Liu, Huaiju; Zhu, Caichao; Sun, Zhangdong; Zhang, Yuanyuan; Song, Chaosheng

2016-01-01

The frictional power loss issue of gear pairs becomes an important concern in both industry and academia due to the requirement of the energy saving and the improvement of power density of gear drives. A thermal starved elastohydrodynamic lubrication model is developed to study the tribological performance of a spur gear pair under starved lubrication conditions. The contact pressure, the film thickness, the temperature rise, the frictional power loss, as well as the coefficient of friction are evaluated by considering the variation of the curvature radius, the sliding/rolling motion, and the load distribution of gear tooth within the meshing period. Effects of lubrication starvation condition, load and speed on the coefficient of friction are studied.

Topology of modified helical gears and Tooth Contact Analysis (TCA) program

Science.gov (United States)

Litvin, Faydor L.; Zhang, Jiao

1989-01-01

The contents of this report covers: (1) development of optimal geometries for crowned helical gears; (2) a method for their generation; (3) tooth contact analysis (TCA) computer programs for the analysis of meshing and bearing contact of the crowned helical gears; and (4) modelling and simulation of gear shaft deflection. The developed method for synthesis was used to determine the optimal geometry for a crowned helical pinion surface and was directed to localize the bearing contact and guarantee favorable shape and a low level of transmission errors. Two new methods for generation of the crowned helical pinion surface are proposed. One is based on the application of a tool with a surface of revolution that slightly deviates from a regular cone surface. The tool can be used as a grinding wheel or as a shaver. The other is based on a crowning pinion tooth surface with predesigned transmission errors. The pinion tooth surface can be generated by a computer-controlled automatic grinding machine. The TCA program simulates the meshing and bearing contact of the misaligned gears. The transmission errors are also determined. The gear shaft deformation was modelled and investigated. It was found that the deflection of gear shafts has the same effect as gear misalignment.

Drawing Evaluation Report for Sampling Equipment Drawings

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

This document presents the results of a task to update the evaluation of River Protection Project (WP) sampling equipment drawings and updates the assigned drawings category as either essential, support, or general drawings. This report updates the drawing evaluation that was originally done per Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation. The scope of this report is limited to updating the evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the RPP Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, all core sampling equipment, and Light Duty Utility Arm (LDUA) (see LMHC contract No. 519, release 10). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The Cone Penetrometer system, which is depicted on vendor drawings, (not H- series), is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and was not included in the original scope for this update and will be addressed in the evaluation update scheduled for later in fiscal year 1999, when equipment ownership is determined

The mechanics of redundantly-driven robotic systems. Final report, September 1988 - December 1995

International Nuclear Information System (INIS)

Tsai, L.W.

1996-04-01

The objectives of this research are to develop systematic methodologies for the creation of multi-degree-of-freedom mechanisms and to gain better understanding of the kinematics, dynamics and control of such devices. The following three inter-related subjects have been studied: (1) tendon-driven manipulators, (2) geared robotic mechanisms, and (3) automotive transmission mechanisms. The main results of this study are summarized

Drawing Inventors

Science.gov (United States)

Szekely, George

2012-01-01

Children are drawing inventors. Their art is certainly not what most adults think of as drawing. Almost instinctively, kids know that drawing is everywhere--that they can draw with almost anything, and that innumerable surfaces can be converted for art use. Teaching drawing is showing interest and enthusiasm for kids' drawing inventions--instead…

Worm gear efficiency model considering misalignment in electric power steering systems

Directory of Open Access Journals (Sweden)

S. H. Kim

2018-05-01

Full Text Available This study proposes a worm gear efficiency model considering misalignment in electric power steering systems. A worm gear is used in Column type Electric Power Steering (C-EPS systems and an Anti-Rattle Spring (ARS is employed in C-EPS systems in order to prevent rattling when the vehicle goes on a bumpy road. This ARS plays a role of preventing rattling by applying preload to one end of the worm shaft but it also generates undesirable friction by causing misalignment of the worm shaft. In order to propose the worm gear efficiency model considering misalignment, geometrical and tribological analyses were performed in this study. For geometrical analysis, normal load on gear teeth was calculated using output torque, pitch diameter of worm wheel, lead angle and normal pressure angle and this normal load was converted to normal pressure at the contact point. Contact points between the tooth flanks of the worm and worm wheel were obtained by mathematically analyzing the geometry, and Hertz's theory was employed in order to calculate contact area at the contact point. Finally, misalignment by an ARS was also considered into the geometry. Friction coefficients between the tooth flanks were also researched in this study. A pin-on-disk type tribometer was set up to measure friction coefficients and friction coefficients at all conditions were measured by the tribometer. In order to validate the worm gear efficiency model, a worm gear was prepared and the efficiency of the worm gear was predicted by the model. As the final procedure of the study, a worm gear efficiency measurement system was set and the efficiency of the worm gear was measured and the results were compared with the predicted results. The efficiency considering misalignment gives more accurate results than the efficiency without misalignment.

The surface fatigue life of contour induction hardened AISI 1552 gears

Science.gov (United States)

Townsend, Dennis P.; Turza, Alan; Chaplin, Mike

1995-07-01

Two groups of spur gears manufactured from two different materials and heat treatments were endurance tested for surface fatigue life. One group was manufactured from AISI 1552 and was finished ground to a 0.4 micron (16 micro-in.) rms surface finish and then dual frequency contour induction hardened. The second group was manufactured from CEVM AISI 9310 and was carburized, hardened, and ground to a 0.4 micron (16 micro-in.) rms surface finish. The gear pitch diameter was 8.89 cm (3.5 in.). Test conditions were a maximum Hertz stress of 1.71 GPa (248 ksi), a bulk gear temperature of approximately 350 K (170 F) and a speed of 10,000 rpm. The lubricant used for the tests was a synthetic paraffinic oil with an additive package. The test results showed that the 10 percent surface fatigue (pitting) life of the contour hardened AISI 1552 test gears was 1.7 times that of the carburized and hardened AISI 9310 test gears. Also there were two early failures of the AISI 1552 gears by bending fatigue.

Motor Integrated Permanent Magnet Gear with a Wide Torque-Speed Range

DEFF Research Database (Denmark)

Rasmussen, Peter Omand; Matzen, Torben N.; Jahns, T. M.

2009-01-01

This paper present a new motor integrated permanent magnet gear with a wide torque-speed range. In the paper a 35 kW permanent magnet motor with a base speed of 4000 rpm and a top speed of 14000 rpm is integrated into a permanent magnetic gear with a gearing ratio of 8.67. The design process...

Integrating Condition Indicators and Usage Parameters for Improved Spiral Bevel Gear Health Monitoring

Science.gov (United States)

Dempsey, Paula J.; Handschuh, Robert F.; Delgado, Irebert, R.

2013-01-01

The objective of this study was to illustrate the importance of combining Health Usage Monitoring Systems (HUMS) data with usage monitoring system data when detecting rotorcraft transmission health. Three gear sets were tested in the NASA Glenn Spiral Bevel Gear Fatigue Rig. Damage was initiated and progressed on the gear and pinion teeth. Damage progression was measured by debris generation and documented with inspection photos at varying torque values. A contact fatigue analysis was applied to the gear design indicating the effect temperature, load and reliability had on gear life. Results of this study illustrated the benefits of combining HUMS data and actual usage data to indicate progression of damage for spiral bevel gears.

Gear wear monitoring by modulation signal bispectrum based on motor current signal analysis

Science.gov (United States)

Zhang, Ruiliang; Gu, Fengshou; Mansaf, Haram; Wang, Tie; Ball, Andrew D.

2017-09-01

Gears are important mechanical components for power transmissions. Tooth wear is one of the most common failure modes, which can present throughout a gear's lifetime. It is significant to accurately monitor gear wear progression in order to take timely predictive maintenances. Motor current signature analysis (MCSA) is an effective and non-intrusive approach which is able to monitor faults from both electrical and mechanical systems. However, little research has been reported in monitoring the gear wear and estimating its severity based on MCSA. This paper presents a novel gear wear monitoring method through a modulation signal bispectrum based motor current signal analysis (MSB-MCSA). For a steady gear transmission, it is inevitable to exist load and speed oscillations due to various errors including wears. These oscillations can induce small modulations in the current signals of the driving motor. MSB is particularly effective in characterising such small modulation signals. Based on these understandings, the monitoring process was implemented based on the current signals from a run-to-failure test of an industrial two stages helical gearbox under a moderate accelerated fatigue process. At the initial operation of the test, MSB analysis results showed that the peak values at the bifrequencies of gear rotations and the power supply can be effective monitoring features for identifying faulty gears and wear severity as they exhibit agreeable changes with gear loads. A monotonically increasing trend established by these features allows a clear indication of the gear wear progression. The dismantle inspection at 477 h of operation, made when one of the monitored features is about 123% higher than its baseline, has found that there are severe scuffing wear marks on a number of tooth surfaces on the driving gear, showing that the gear endures a gradual wear process during its long test operation. Therefore, it is affirmed that the MSB-MSCA approach proposed is reliable

User-driven innovation in tourism

DEFF Research Database (Denmark)

Hjalager, Anne-Mette; Nordin, Sara

2011-01-01

This literature study reviews user-driven innovation and establishes a typology of its forms in a tourism context. Sixteen methods are distinguishable. They comprise situations where users are actively involved and methods where information is collected without direct user involvement. The nature...... and intensity of the dialogue between companies and their customers are addressed. Drawing on this existing research, the article concludes that there is still little comprehensive follow-up on user-driven innovation in tourism and its impact on quality improvements and assurance. Key areas for future studies...

TWRS system drawings and field verification

International Nuclear Information System (INIS)

Shepard, D.G.

1995-01-01

The Configuration Management Program combines the TWRS Labeling and O and M drawing and drawing verification programs. The combined program will produce system drawings for systems that are normally operated or have maintenance performed on the system, label individual pieces of equipment for proper identification, even if system drawings are not warranted, and perform verification of drawings that are identified as essential in Tank Farm Essential Drawing Plans. During fiscal year 1994, work was begun to label Tank Farm components and provide user friendly system based drawings for Tank Waste Remediation System (TWRS) operations and maintenance. During the first half of fiscal 1995, the field verification program continued to convert TWRS drawings into CAD format and verify the accuracy based on visual inspections. During the remainder of fiscal year 1995 these efforts will be combined into a single program providing system based drawings and field verification of TWRS equipment and facilities. This combined program for TWRS will include all active systems for tank farms. Operations will determine the extent of drawing and labeling requirements for single shell tanks, i.e. the electrical distribution, HVAC, leak detection, and the radiation monitoring system. The tasks required to meet these objectives, include the following: identify system boundaries or scope for drawing being verified; label equipment/components in the process systems with a unique Equipment Identification Number (EIN) per the TWRS Data Standard; develop system drawings that are coordinated by ''smart'' drawing numbers and/or drawing references as identified on H-14-020000; develop a Master Equipment List (MEL) multi-user data base application which will contain key information about equipment identified in the field; and field verify and release TWRS Operation and Maintenance (O and M) drawings

DrawFromDrawings: 2D Drawing Assistance via Stroke Interpolation with a Sketch Database.

Science.gov (United States)

Matsui, Yusuke; Shiratori, Takaaki; Aizawa, Kiyoharu

2017-07-01

We present DrawFromDrawings, an interactive drawing system that provides users with visual feedback for assistance in 2D drawing using a database of sketch images. Following the traditional imitation and emulation training from art education, DrawFromDrawings enables users to retrieve and refer to a sketch image stored in a database and provides them with various novel strokes as suggestive or deformation feedback. Given regions of interest (ROIs) in the user and reference sketches, DrawFromDrawings detects as-long-as-possible (ALAP) stroke segments and the correspondences between user and reference sketches that are the key to computing seamless interpolations. The stroke-level interpolations are parametrized with the user strokes, the reference strokes, and new strokes created by warping the reference strokes based on the user and reference ROI shapes, and the user study indicated that the interpolation could produce various reasonable strokes varying in shapes and complexity. DrawFromDrawings allows users to either replace their strokes with interpolated strokes (deformation feedback) or overlays interpolated strokes onto their strokes (suggestive feedback). The other user studies on the feedback modes indicated that the suggestive feedback enabled drawers to develop and render their ideas using their own stroke style, whereas the deformation feedback enabled them to finish the sketch composition quickly.

Influences of lubricant pocket geometry and working conditions upon micro lubrication mechanisms in upsetting and strip drawing

DEFF Research Database (Denmark)

Shimizu, Ichiro; Martins, P. A. F.; Bay, Niels

2010-01-01

, during upsetting and strip drawing, by means of a rigid-viscoplastic finite-element formulation. Special emphasis is placed on the effect of pocket geometry on the build-up of hydrostatic pressure, which is responsible for the onset of micro-lubrication mechanisms. A good agreement is found between......Micro-lubricant pockets located in the surface of plastically deforming workpieces are recognised to improve the performance of fluid lubrication in a metal-forming process. This work investigates the joint influence of pocket geometry and process working conditions on micro-lubrication mechanisms...

A Comparative Study of Simulated and Measured Gear-Flap Flow Interaction

Science.gov (United States)

Khorrami, Mehdi R.; Mineck, Raymond E.; Yao, Chungsheng; Jenkins, Luther N.; Fares, Ehab

2015-01-01

The ability of two CFD solvers to accurately characterize the transient, complex, interacting flowfield asso-ciated with a realistic gear-flap configuration is assessed via comparison of simulated flow with experimental measurements. The simulated results, obtained with NASA's FUN3D and Exa's PowerFLOW® for a high-fidelity, 18% scale semi-span model of a Gulfstream aircraft in landing configuration (39 deg flap deflection, main landing gear on and off) are compared to two-dimensional and stereo particle image velocimetry measurements taken within the gear-flap flow interaction region during wind tunnel tests of the model. As part of the bench-marking process, direct comparisons of the mean and fluctuating velocity fields are presented in the form of planar contour plots and extracted line profiles at measurement planes in various orientations stationed in the main gear wake. The measurement planes in the vicinity of the flap side edge and downstream of the flap trailing edge are used to highlight the effects of gear presence on tip vortex development and the ability of the computational tools to accurately capture such effects. The present study indicates that both computed datasets contain enough detail to construct a relatively accurate depiction of gear-flap flow interaction. Such a finding increases confidence in using the simulated volumetric flow solutions to examine the behavior of pertinent aer-odynamic mechanisms within the gear-flap interaction zone.

Review on common calibration and measurement practises for measuring gears on CMMs

DEFF Research Database (Denmark)

Sammatini-Malberg, Maria-Pia; De Chiffre, Leonardo

, in order to give an overview of the improvements achieved in the last 25 years. Special attention is paid to gear metrology on coordinate measuring machines (CMMs). Calibration chains for the major gear geometrical quantities developed by Physikalisch-Technische Bundesanstalt (PTB) as well as their recent...... results obtained in gear standards measurement uncertainties are presented. This review also describes the design and development of a new type of master gear: the Gauge Block Gear (GBG).The GBG was developed for the performance verification of CMMs, for the specific task of pitch and chordal tooth...... thickness measurement. Its main characteristic is the replacement of the teeth with gauge blocks, in order to achieve direct traceability of the chordal tooth thickness...

Perancangan dan Realisasi Kontrol Prototype Landing Gear System Menggunakan PLCmikro berbasis Mikrokontroller PIC16F877A

Directory of Open Access Journals (Sweden)

RATNA SUSANA

2016-02-01

Full Text Available Abstrak Landing gear system merupakan suatu sistem penggerak pada roda pesawat yang menggunakan electromechanic system dengan sejumlah relay tanpa control terpusat. Melalui penelitian ini, electromechanic system tersebut diubah menjadi landing gear system yang dikendalikan secara terpusat menggunakan mikrokontroller dan diprogram oleh ldmikro berbahasa ladder diagram yang kemudian lebih dikenal dengan nama “PLCmikro”. Input discreate digunakan untuk menggerakkan aktuator solenoid valve agar piston double acting cylinder dapat bekerja sesuai sistem yang diinginkan. Input analog digunakan sebagai informasi ketinggian pesawat minimum agar pesawat tetap aman terbang di udara. Control Landing gear system yang direalisasikan berhasil menggerakkan piston masuk maupun keluar dari tabung, memberikan informasi proses pergerakkan piston yang bermasalah dan posisi roda yang telah masuk atau keluar dari pesawat berupa lampu LED. Sistem ini juga berhasil membaca informasi ketinggian minimum pesawat dari potensiometer serta mengubahnya menjadi informasi suara dan lampu LED.   Kata kunci: Landing gear system, PLCmikro, Ldmikro, ladder diagram, double acting cylinder. Abstract The landing gear system an aircraft wheel drive system that uses electromechanic system with a relay without any centralized control. Through this study, the electromechanic system was changed to landing gear system with a centrally controlled by using microcontroller and programmed with ldmikro ladder diagram language which came to be known by the name of "PLCmikro". Discreate input used to drive the actuator solenoid valve double acting cylinder so that the piston can work as desired system. The analog input is used as the minimum flight altitude information to keep the plane safe to fly in the air. Landing gear control system is realized successfully drive the piston in and out of the tube, providing information processes are problematic piston movement and wheel position that has

Dynamic load-sharing characteristic analysis of face gear power-split gear system based on tooth contact characteristics

Science.gov (United States)

Dong, Hao; Hu, Yahui

2018-04-01

The bend-torsion coupling dynamics load-sharing model of the helicopter face gear split torque transmission system is established by using concentrated quality standard, to analyzing the dynamic load-sharing characteristic. The mathematical models include nonlinear support stiffness, time-varying meshing stiffness, damping, gear backlash. The results showed that the errors collectively influenced the load sharing characteristics, only reduce a certain error, it is never fully reached the perfect loading sharing characteristics. The system load-sharing performance can be improved through floating shaft support. The above-method will provide a theoretical basis and data support for its dynamic performance optimization design.

OPTIMIZATION OF HEATING OF GEAR WHEEL USING NUMERICAL MODELING

Directory of Open Access Journals (Sweden)

Soňa Benešová

2013-09-01

Full Text Available Successful heat treating and carburizing of gear wheels for wind turbine gear boxes requires that plastic deformation in the wheel is minimized. Numerical modeling using the DEFORM software was aimed at exploring the effects of the base, on which the gear wheel rests during heating, on the heating process. Homogeneous heating was assumed. It was found that the base heats up more quickly than the workpiece. It is the consequence of the base's shape and volume. As a result, the base expands and slides against the wheel, predominantly at the first heating stage. Later on, it prevents the gear wheel from expanding, causing plastic deformation in the wheel. The findings were used for designing new heating schedules to minimize these undesirable interactions and to reduce the plastic deformation to a negligible magnitude. In addition, this paper presents an example of a practical use of numerical modeling in the DEFORM software.

OPTIMIZATION OF HEATING OF GEAR WHEEL USING NUMERICAL MODELING

Directory of Open Access Journals (Sweden)

Sona Benesova

2013-05-01

Full Text Available Successful heat treating and carburizing of gear wheels for wind turbine gear boxes requires that plastic deformation in the wheel is minimized. Numerical modeling using the DEFORM software was aimed at exploring the effects of the base, on which the gear wheel rests during heating, on the heating process. Homogeneous heating was assumed. It was found that the base heats up more quickly than the workpiece. It is the consequence of the base's shape and volume. As a result, the base expands and slides against the wheel, predominantly at the first heating stage. Later on, it prevents the gear wheel from expanding, causing plastic deformation in the wheel. The findings were used for designing new heating schedules to minimize these undesirable interactions and to reduce the plastic deformation to a negligible magnitude. In addition, this paper presents an example of a practical use of numerical modeling in the DEFORM software.

Experimental Research on Vibrations of Double Harmonic Gear Transmission

Directory of Open Access Journals (Sweden)

Sava Ianici

2017-11-01

Full Text Available Gears transmission can be important sources of vibration in the mechanical system structures and can have a significant share in the overall vibration level. The current trend of significant increase in powers and speeds transmitted by modern mechanical systems, along with the size reduction, may cause a worsening of the behaviour of transmissions with gears in terms of vibration, especially when the optimization criteria were not respected in the design, execution and installation phase. This paper presents a study of vibrations that occur in a double harmonic gear transmission (DHGT, based on experimental research. The experimental researches revealed that in a double harmonic gear transmission the vibrations are initiated and develop in the multipara harmonics engagement of the teeth and in the kinematic couplings materialized between the wave generator and the flexible toothed wheel. These vibrations are later transmitted by means of the shafts and bearings to the transmission housing, respectively, through the walls of it, propagating in the air.

Modeling of Two-Wheeled Self-Balancing Robot Driven by DC Gearmotors

Directory of Open Access Journals (Sweden)

Frankovský P.

2017-08-01

Full Text Available This paper is aimed at modelling a two-wheeled self-balancing robot driven by the geared DC motors. A mathematical model consists of two main parts, the model of robot’s mechanical structure and the model of the actuator. Linearized equations of motion are derived and the overall model of the two-wheeled self-balancing robot is represented in state-space realization for the purpose of state feedback controller design.

Vehicle transmission gear 2009; Getriebe in Fahrzeugen 2009

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

Within the VDI Conference 'Vehicle Transmission Gears' at 30th June to 1st May, 2009 in Friedrichshafen (Federal Republic of Germany), the following lectures were held: (1) Production site Germany - Home in trend (B.O. Braun); (2) Luk CVT Technology - Efficiency, comfort, dynamics (A. Teubert); (3) The new BMW eight-speed automatic gear (J. Kretschmer); (4) Influence of transmission concept and design on simulated fuel consumption in official customer driving cycles (A. Schmidt); (5) GETRAG PowerShift {sup registered} - Extended driving functionalities due to controllable double clutch (A. Pawlenka); (6) New efficient transmission strategy in automatic transmission in the city bus (H. Nolzen); (7) Electronic controllers for gears: decision about design concepts und applied technologies on the basis of the place of installation in vehicles (P. Bertelshofer); (8) Coupled systems based on magnetorheological fluids (D. Gueth); (9) Investigation of setting losses of diaphragm springs in dry-running couplings according to given conditions (P. Merkel); (10) Influence of material properties and heat balance on the tribologic behaviour of dry-running friction couplings (C. Spaeth); (11) A contribution to massively transformed components of gears for the reduction of consumption and resources saving (G. Quintenz); (12) An economic production of transmission shafts by means of near netshape transformation also in the area of commercial vehicles (E. Rauschnabel); (13) Potentials and transformation of design and process optimization in the serial production using hypoid interlocking as an example (A. Dietrich); (14) Development of automated manual transmission (Se-il Song); (15) Integration of new functions to GETRAG PowerShift {sup registered} Transmissions of transversal, transaxle powertrains (I. Steinberg); (16) Automatedmanual transmission - The forgotten concept for the future? (B.-R. Hoehn); (17) A new back-torque limiter for high power motorcycles

Gear Fault Detection Effectiveness as Applied to Tooth Surface Pitting Fatigue Damage

Science.gov (United States)

Lewicki, David G.; Dempsey, Paula J.; Heath, Gregory F.; Shanthakumaran, Perumal

2010-01-01

A study was performed to evaluate fault detection effectiveness as applied to gear-tooth-pitting-fatigue damage. Vibration and oil-debris monitoring (ODM) data were gathered from 24 sets of spur pinion and face gears run during a previous endurance evaluation study. Three common condition indicators (RMS, FM4, and NA4 [Ed. 's note: See Appendix A-Definitions D were deduced from the time-averaged vibration data and used with the ODM to evaluate their performance for gear fault detection. The NA4 parameter showed to be a very good condition indicator for the detection of gear tooth surface pitting failures. The FM4 and RMS parameters perfomu:d average to below average in detection of gear tooth surface pitting failures. The ODM sensor was successful in detecting a significant 8lDOunt of debris from all the gear tooth pitting fatigue failures. Excluding outliers, the average cumulative mass at the end of a test was 40 mg.

Gear noise, vibration, and diagnostic studies at NASA Lewis Research Center

Science.gov (United States)

Zakrajsek, J. J.; Oswald, F. B.; Townsend, D. P.; Coy, J. J.

1990-01-01

The NASA Lewis Research Center and the U.S. Army Aviation Systems Command are involved in a joint research program to advance the technology of rotorcraft transmissions. This program consists of analytical as well as experimental efforts to achieve the overall goals of reducing weight, noise, and vibration, while increasing life and reliability. Recent analytical activities are highlighted in the areas of gear noise, vibration, and diagnostics performed in-house and through NASA and U.S. Army sponsored grants and contracts. These activities include studies of gear tooth profiles to reduce transmission error and vibration as well as gear housing and rotordynamic modeling to reduce structural vibration and transmission and noise radiation, and basic research into current gear failure diagnostic methodologies. Results of these activities are presented along with an overview of near-term research plans in the gear noise, vibration, and diagnostics area.

Drawing experts have better visual memory while drawing

NARCIS (Netherlands)

Perdreau, F.A.G.; Cavanagh, P.

2015-01-01

Drawing involves frequent shifts of gaze between the original and the drawing and visual memory helps compare the original object and the drawing across these gaze shifts while creating and correcting the drawing. It remains unclear whether this memory encodes all of the object or only the features

Computerized Design of Low-noise Face-milled Spiral Bevel Gears

Science.gov (United States)

Litvin, Faydor L.; Zhang, YI; Handschuh, Robert F.

1994-01-01

An advanced design methodology is proposed for the face-milled spiral bevel gears with modified tooth surface geometry that provides a reduced level of noise and has a stabilized bearing contact. The approach is based on the local synthesis of the gear drive that provides the 'best' machine-tool settings. The theoretical aspects of the local synthesis approach are based on the application of a predesigned parabolic function for absorption of undesirable transmission errors caused by misalignment and the direct relations between principal curvatures and directions for mating surfaces. The meshing and contact of the gear drive is synthesized and analyzed by a computer program. The generation of gears with the proposed geometry design can be accomplished by application of existing equipment. A numerical example that illustrates the proposed theory is presented.

Generation of helical gears with new surfaces topology by application of CNC machines

Science.gov (United States)

Litvin, F. L.; Chen, N. X.; Hsiao, C. L.; Handschuh, Robert F.

1993-01-01

Analysis of helical involute gears by tooth contact analysis shows that such gears are very sensitive to angular misalignment that leads to edge contact and the potential for high vibration. A new topology of tooth surfaces of helical gears that enables a favorable bearing contact and a reduced level of vibration is described. Methods for grinding of the helical gears with the new topology are proposed. A TCA (tooth contact analysis) program for simulation of meshing and contact of helical gears with the new topology has been developed. Numerical examples that illustrate the proposed ideas are discussed.

Comparison of Epicyclic Gearing Design Methods by Means of Quality Criteria Evaluation

Directory of Open Access Journals (Sweden)

I. V. Leonov

2015-01-01

Full Text Available The performance of modern economy depends on the usage of different machines. Execution of the many tasks a society entrusts to the machinery requires a huge amount of the mechanical energy imparted to the mechanical system due to different engines. Combining the motors and actuators in turn occurs through various transmissions.Among the numerous types of transmission the planetary gears occupy an important place. With a number of advantages and differences from other types of transmission of rotational motion, planetary gear can be used as a gear or a differential gear. The planetary gear firmly holds a leading position for its frequent use in transmissions of various technological and transport vehicles, as it has a convenient layout and high load capacity.Despite the fact that people have been using planetary gears over two thousand years, there is no simple method of their design, allowing both a minimizing design time and an optimization of their performance characteristics and technological qualities.The proposed design method is derived from the classical method of factors. It limits the number of options by isolating a promising region of a set of reduced criteria values of the overall dimensions, one of the main design criteria. A minimizing size criterion optimization is provided through rapprochement of gear sizes in two rows of gearings and proximity to the minimum possible number of teeth from the undercut condition, environment for numerous satellites, and gear assembly as well as through specifying the numbers of teeth of one of the rows to be equal to the arithmetic average of the teeth numbers of the other row.

Way of Working for Embedded Control Software using Model-Driven Development Techniques

NARCIS (Netherlands)

Bezemer, M.M.; Groothuis, M.A.; Brugali, D.; Schlegel, C.; Broenink, Johannes F.

2011-01-01

Embedded targets normally do not have much resources to aid developing and debugging the software. So model-driven development (MDD) is used for designing embedded software with a `first time right' approach. For such an approach, a good way of working (WoW) is required for embedded software

Encountering Drawing

Science.gov (United States)

Gregory, Nuala

2017-01-01

This article divides into two roughly equal parts, both of which aim to address the "act" rather than the "art" of drawing. The second part focuses on a theoretical discussion of drawing. The first bears on a number of themes including the role of drawing in colonial history, drawing and data collection, and drawing and memory.…

Gear-box fault detection using time-frequency based methods

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob

2015-01-01

Gear-box fault monitoring and detection is important for optimization of power generation and availability of wind turbines. The current industrial approach is to use condition monitoring systems, which runs in parallel with the wind turbine control system, using expensive additional sensors...... in the gear-box resonance frequency can be detected. Two different time–frequency based approaches are presented in this paper. One is a filter based approach and the other is based on a Karhunen–Loeve basis. Both of them detect the gear-box fault with an acceptable detection delay of maximum 100s, which...... is neglectable compared with the fault developing time....

Stimulating Scientific Reasoning with Drawing-Based Modeling

Science.gov (United States)

Heijnes, Dewi; van Joolingen, Wouter; Leenaars, Frank

2018-01-01

We investigate the way students' reasoning about evolution can be supported by drawing-based modeling. We modified the drawing-based modeling tool SimSketch to allow for modeling evolutionary processes. In three iterations of development and testing, students in lower secondary education worked on creating an evolutionary model. After each…

An efficient finite element solution for gear dynamics

International Nuclear Information System (INIS)

Cooley, C G; Parker, R G; Vijayakar, S M

2010-01-01

A finite element formulation for the dynamic response of gear pairs is proposed. Following an established approach in lumped parameter gear dynamic models, the static solution is used as the excitation in a frequency domain solution of the finite element vibration model. The nonlinear finite element/contact mechanics formulation provides accurate calculation of the static solution and average mesh stiffness that are used in the dynamic simulation. The frequency domain finite element calculation of dynamic response compares well with numerically integrated (time domain) finite element dynamic results and previously published experimental results. Simulation time with the proposed formulation is two orders of magnitude lower than numerically integrated dynamic results. This formulation admits system level dynamic gearbox response, which may include multiple gear meshes, flexible shafts, rolling element bearings, housing structures, and other deformable components.

14 CFR 23.729 - Landing gear extension and retraction system.

Science.gov (United States)

2010-01-01

... retracted) position. If switches are used, they must be located and coupled to the landing gear mechanical... burst, or rocks, water, and slush that may enter the landing gear bay. [Doc. No. 4080, 29 FR 17955, Dec...

NUMERICAL ANALYSIS AND EXPERIMENTAL INVESTIGATION OF DISK SPRING CONFIGURATIONS WITH REGARD TO LOAD CAPACITY OF SAFETY PROGRESSIVE GEARS

Directory of Open Access Journals (Sweden)

Paweł LONKWIC

2016-09-01

Full Text Available The paper investigates the effect of various disk spring package configurations on brake load of safety progressive gears. The numerical analysis is performed using the Abaqus/CAE software and the designed 3D models. The numerical results are then verified in experimental tests. The tests also examine the effect of lubrication on brake load of spring packages. In addition, the paper investigates the work conditions of safety progressive gears at emergency braking. The experimental results show agreement with the numerical results.

Model Based Approach for Identification of Gears and Bearings Failure Modes

Directory of Open Access Journals (Sweden)

Renata Klein

2011-01-01

Full Text Available This paper describes the algorithms that were used for analysis of the PHM’09 gear-box. The purpose of the analysis was to detect and identify faults in various components of the gear-box. Each of the 560 vibration recordings presented a different set of faults, including distributed and localized gear faults, typical bearing faults and shaft faults. Each fault had to be pinpointed precisely.In the following sections we describe the algorithms used for finding faults in bearings, gears and shafts, and the conclusions that were reached. A special blend of pattern recognition and signal processing methods was applied.Bearings were analyzed using the orders representation of the envelope of a band pass filtered signal and an envelope of the de-phased signal. A special search algorithm was applied for bearings features extraction. The diagnostics of the bearings failure modes was carried out automatically. Gears were analyzed using the order domains, the quefrency of orders, and the derivatives of the phase average.

Helical Face Gear Development Under the Enhanced Rotorcraft Drive System Program

Science.gov (United States)

Heath, Gregory F.; Slaughter, Stephen C.; Fisher, David J.; Lewicki, David G.; Fetty, Jason

2011-01-01

U.S. Army goals for the Enhanced Rotorcraft Drive System Program are to achieve a 40 percent increase in horsepower to weight ratio, a 15 dB reduction in drive system generated noise, 30 percent reduction in drive system operating, support, and acquisition cost, and 75 percent automatic detection of critical mechanical component failures. Boeing s technology transition goals are that the operational endurance level of the helical face gearing and related split-torque designs be validated to a TRL 6, and that analytical and manufacturing tools be validated. Helical face gear technology is being developed in this project to augment, and transition into, a Boeing AH-64 Block III split-torque face gear main transmission stage, to yield increased power density and reduced noise. To date, helical face gear grinding development on Northstar s new face gear grinding machine and pattern-development tests at the NASA Glenn/U.S. Army Research Laboratory have been completed and are described.

Influence of the shot-peening treatment on the CRF gearing behaviour

International Nuclear Information System (INIS)

Molinie, D.; Lemaire, E.; Randrianarivo, L.; Dorier, C.

1998-01-01

Surface damage are observed in service on CRF case-hardened cases. Such damage is like surface fatigue which appears in the form of frosting and can come to a micro-spalling or even a spalling damage. Survey and studies realised on gears affected by such damage, led EDF and the manufacturer to search for appropriated solutions since 1985 (optimisation of the gear bottom profile, care of the grinding and the thermochemical processing, use of oils with higher viscosity). Simulations on a running wheel device can reproduce the meshing conditions on simplified specimen. The aim is to study the influence of residual stresses following a severe grinding and shot peening treatments. An empiric selection was realised among different shot peening treatments. Endurance tests are realised on case-hardened gears with or without shot-peening treatments. Compared with standard grinded gears, it appears that the shot-peening selected increases up to 40% the gear lifetime till extended spalling. (authors)

Predicting lethal entanglements as a consequence of drag from fishing gear.

Science.gov (United States)

van der Hoop, Julie M; Corkeron, Peter; Henry, Allison G; Knowlton, Amy R; Moore, Michael J

2017-02-15

Large whales are frequently entangled in fishing gear and sometimes swim while carrying gear for days to years. Entangled whales are subject to additional drag forces requiring increased thrust power and energy expenditure over time. To classify entanglement cases and aid potential disentanglement efforts, it is useful to know how long an entangled whale might survive, given the unique configurations of the gear they are towing. This study establishes an approach to predict drag forces on fishing gear that entangles whales, and applies this method to ten North Atlantic right whale cases to estimate the resulting increase in energy expenditure and the critical entanglement duration that could lead to death. Estimated gear drag ranged 11-275N. Most entanglements were resolved before critical entanglement durations (mean±SD 216±260days) were reached. These estimates can assist real-time development of disentanglement action plans and U.S. Federal Serious Injury assessments required for protected species. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bernard Tschumi Draws Architecture!

Directory of Open Access Journals (Sweden)

Gevork Hartoonian

2014-08-01

Full Text Available Bernard Tschumi’s delineation prepared for the Museu de Arte Contemporânea provides the starting point for this essay, which discusses the historicity of drawing and highlights the horizontality and the verticality that structure architecture’s contrast with the pictorial realm. Juxtaposing a freehand sketch with the digital image of the same project, Tschumi moves to address the paradox concerning the position of the body and drawing. This drawing also speaks for the reversal in the position of the body brought about by digital reproductivity.The reversal alludes to Tschumi’s theorization of architecture in terms of space and event. These, I will argue, are anticipated in The Manhattan Transcripts (1981 where a set of freehand drawings is used to evoke a filmic mood wherein the image is projected parallel to the spectator’s seated position. The essay goes further, suggesting that the theatricality permeating the present architecture is part of the shift from horizontality to the painterly, and yet the phenomenon is not merely a technical issue. Rather, it alludes to architecture’s dialogical rapport with painting at work since the Renaissance.

Time domain series system definition and gear set reliability modeling

International Nuclear Information System (INIS)

Xie, Liyang; Wu, Ningxiang; Qian, Wenxue

2016-01-01

Time-dependent multi-configuration is a typical feature for mechanical systems such as gear trains and chain drives. As a series system, a gear train is distinct from a traditional series system, such as a chain, in load transmission path, system-component relationship, system functioning manner, as well as time-dependent system configuration. Firstly, the present paper defines time-domain series system to which the traditional series system reliability model is not adequate. Then, system specific reliability modeling technique is proposed for gear sets, including component (tooth) and subsystem (tooth-pair) load history description, material priori/posterior strength expression, time-dependent and system specific load-strength interference analysis, as well as statistically dependent failure events treatment. Consequently, several system reliability models are developed for gear sets with different tooth numbers in the scenario of tooth root material ultimate tensile strength failure. The application of the models is discussed in the last part, and the differences between the system specific reliability model and the traditional series system reliability model are illustrated by virtue of several numerical examples. - Highlights: • A new type of series system, i.e. time-domain multi-configuration series system is defined, that is of great significance to reliability modeling. • Multi-level statistical analysis based reliability modeling method is presented for gear transmission system. • Several system specific reliability models are established for gear set reliability estimation. • The differences between the traditional series system reliability model and the new model are illustrated.

Fault feature analysis of cracked gear based on LOD and analytical-FE method

Science.gov (United States)

Wu, Jiateng; Yang, Yu; Yang, Xingkai; Cheng, Junsheng

2018-01-01

At present, there are two main ideas for gear fault diagnosis. One is the model-based gear dynamic analysis; the other is signal-based gear vibration diagnosis. In this paper, a method for fault feature analysis of gear crack is presented, which combines the advantages of dynamic modeling and signal processing. Firstly, a new time-frequency analysis method called local oscillatory-characteristic decomposition (LOD) is proposed, which has the attractive feature of extracting fault characteristic efficiently and accurately. Secondly, an analytical-finite element (analytical-FE) method which is called assist-stress intensity factor (assist-SIF) gear contact model, is put forward to calculate the time-varying mesh stiffness (TVMS) under different crack states. Based on the dynamic model of the gear system with 6 degrees of freedom, the dynamic simulation response was obtained for different tooth crack depths. For the dynamic model, the corresponding relation between the characteristic parameters and the degree of the tooth crack is established under a specific condition. On the basis of the methods mentioned above, a novel gear tooth root crack diagnosis method which combines the LOD with the analytical-FE is proposed. Furthermore, empirical mode decomposition (EMD) and ensemble empirical mode decomposition (EEMD) are contrasted with the LOD by gear crack fault vibration signals. The analysis results indicate that the proposed method performs effectively and feasibility for the tooth crack stiffness calculation and the gear tooth crack fault diagnosis.

COMPARATIVE STUDY OF COMMANDS TO GENERATE GEARS FROM DIFFERENT SOFTWARE DESIGN

Directory of Open Access Journals (Sweden)

GOANȚĂ Adrian Mihai

2015-06-01

Full Text Available The paper aims to approach commands for the automatic generation of cylindrical gears with right teeth and involute profile that can be used to obtain further cylindrical gears. The following software is investigated: NX 7.5 and Inventor Professional 2011. The author presents in detailed analysis if the software itself contains instructions for generating gears or require an additional patch. The paper presents the results of applying those commands and direct or indirect possibilities of obtaining a cylindrical gear with right/straight teeth. After a thorough study, the conclusions are drawn about the strengths and weaknesses of each software in use, and recommendations are made in accordance with the author’s opinions.

Latino/a Immigrant Children's Drawings and Writings

Science.gov (United States)

Soto, Lourdes Diaz; Garza, Irene

2011-01-01

This article shares children's drawings and writings reflecting immigration border-crossing experiences in south Texas, USA. The authors present the children's drawings as well as their narratives, relying on the work of Robert Coles and the authors' own intuitive Latina/Xicana lenses. The authors' intent is to pursue the possibility of future…

Improve Gear Fault Diagnosis and Severity Indexes Determinations via Time Synchronous Average

Directory of Open Access Journals (Sweden)

Mohamed El Morsy

2016-11-01

Full Text Available In order to reduce operation and maintenance costs, prognostics and health management (PHM of the geared system is needed to improve effective gearbox fault detection tools.  PHM system allows less costly maintenance because it can inform operators of needed repairs before a fault causes collateral damage happens to the gearbox. In this article, time synchronous average (TSA technique and complex continuous wavelet analysis enhancement are used as gear fault detection approach. In the first step, extract the periodic waveform from the noisy measured signal is considered as The main value of Time synchronous averaging (TSA for gearbox signals analyses, where it allows the vibration signature of the gear under analysis to be separated from other gears and noise sources in the gearbox that are not synchronous with faulty gear. In the second step, the complex wavelet analysis is used in case of multi-faults in same gear. The signal phased-locked with the angular position of a shaft within the system is done. The main aims for this research is to improve the gear fault diagnosis and severity index determinations based on TSA  of measured signal for investigated passenger vehicle gearbox under different operation conditions. In addition to, correct the variations in shaft speed such that the spreading of spectral energy into an adjacent gear mesh bin helps in detecting the gear fault position (faulted tooth or teeth and improve the Root Mean Square (RMS, Kurtosis, and Peak Pulse as the sensitivity of severity indexes for maintenance, prognostics and health management (PHM purposes. The open loop test stand is equipped with two dynamometers and investigated vehicle gearbox of mid-size passenger car; the total power is taken-off from one side only. Reference Number: www.asrongo.org/doi:4.2016.1.1.6

Investigation of Spiral Bevel Gear Condition Indicator Validation Via AC-29-2C Using Damage Progression Tests

Science.gov (United States)

Dempsey, Paula J.

2014-01-01

This report documents the results of spiral bevel gear rig tests performed under a NASA Space Act Agreement with the Federal Aviation Administration (FAA) to support validation and demonstration of rotorcraft Health and Usage Monitoring Systems (HUMS) for maintenance credits via FAA Advisory Circular (AC) 29-2C, Section MG-15, Airworthiness Approval of Rotorcraft (HUMS) (Ref. 1). The overarching goal of this work was to determine a method to validate condition indicators in the lab that better represent their response to faults in the field. Using existing in-service helicopter HUMS flight data from faulted spiral bevel gears as a "Case Study," to better understand the differences between both systems, and the availability of the NASA Glenn Spiral Bevel Gear Fatigue Rig, a plan was put in place to design, fabricate and test comparable gear sets with comparable failure modes within the constraints of the test rig. The research objectives of the rig tests were to evaluate the capability of detecting gear surface pitting fatigue and other generated failure modes on spiral bevel gear teeth using gear condition indicators currently used in fielded HUMS. Nineteen final design gear sets were tested. Tables were generated for each test, summarizing the failure modes observed on the gear teeth for each test during each inspection interval and color coded based on damage mode per inspection photos. Gear condition indicators (CI) Figure of Merit 4 (FM4), Root Mean Square (RMS), +/- 1 Sideband Index (SI1) and +/- 3 Sideband Index (SI3) were plotted along with rig operational parameters. Statistical tables of the means and standard deviations were calculated within inspection intervals for each CI. As testing progressed, it became clear that certain condition indicators were more sensitive to a specific component and failure mode. These tests were clustered together for further analysis. Maintenance actions during testing were also documented. Correlation coefficients were

The influence of mechanical gear on the efficiency of small hydropower

Science.gov (United States)

Ferenc, Zbigniew; Sambor, Aleksandra

2017-11-01

Pursuant to the "Strategy of development of renewable energy", an increase in the share of renewable energy sources in the national fuel-energy balance up to 14% by 2020 is planned in the structure of usage of primary energy carriers. The change in the participation of the clean energy in the energy balance may be done not only by the erection of new and renovation of the already existing plants, but also through an improvement of their energetic efficiency. The study presents the influence of the mechanical gear used on the quantity of energy produced by a small hydropower on the basis of SHP Rzepcze in Opole province in 2005-2010. The primary kinematic system was composed of a Francis turbine of a vertical axis, a toothed intersecting axis gear of 1:1 ratio, a belt gear of a double ratio. After a modernization the system was simplified by means of reducing the intersecting axis gear and the double ratio of the belt gear. The new kinematic system utilized a single-ratio belt gear of a vertical axis. After the kinematic system was rearranged, a significant improvement of efficiency of the small hydropower was concluded, which translates into an increase of the amount of energy produced.

Contactless Mechanical Components: Gears, Torque Limiters and Bearings

Directory of Open Access Journals (Sweden)

Jose Luis Perez-Diaz

2014-12-01

Full Text Available Contactless mechanical components are mechanical sets for conversion of torque/speed, whose gears and moving parts do not touch each other, but rather they provide movement with magnets and magnetic materials that exert force from a certain distance. Magneto-mechanical transmission devices have several advantages over conventional mechanisms: no friction between rotatory elements (no power losses or heat generation by friction so increase of efficiency, no lubrication is needed (oil-free mechanisms and no lubrication auxiliary systems, reduced maintenance (no lubricant so no need of oil replacements, wider operational temperature ranges (no lubricant evaporation or freezing, overload protection (if overload occurs magnet simply slides but no teeth brake, through-wall connection (decoupling of thermal and electrical paths and environmental isolation, larger operative speeds (more efficient operative conditions, ultralow noise and vibrations (no contact no noise generation. All these advantages permit us to foresee in the long term several common industrial applications in which including contactless technology would mean a significant breakthrough for their performance. In this work, we present three configurations of contactless mechanical passive components: magnetic gears, magnetic torque limiters and superconducting magnetic bearings. We summarize the main characteristic and range of applications for each type; we show experimental results of the most recent developments showing their performance.

Mechanical drawing

Energy Technology Data Exchange (ETDEWEB)

Cho, Ho Seon; Lee, Geun Hui

2004-04-15

This book deals with how to read and draw the mechanical drawing, which includes the basic of drawing like purpose, kinds, and criterion, projection, special projection drawing, omission of the figure, section, and types of section, dimensioning method, writing way of allowable limit size, tolerance of regular size, parts list and assembling drawing, fitting, mechanical elements like screw, key, pin, rivet, spring, bearing, pipe, valve, welding, geometric tolerance and mechanical materials.

Impedance Synthesis Based Vibration Analysis of Geared Transmission System

Directory of Open Access Journals (Sweden)

Yafeng Ren

2017-01-01

Full Text Available The severity of gear noise response depends on the sensitivity of geared rotor system dynamics to the transmission error. As gearbox design trending towards lighter weight and lower noise, the influence of housing compliance on system dynamic characteristics cannot be ignored. In this study, a gear-shaft-bearing-housing coupled impedance model is proposed to account for the effect of housing compliance on the vibration of geared transmission system. This proposed dynamic model offers convenient modeling, efficient computing, and ability to combine computed parameters with experimental ones. The numerical simulations on system dynamic characteristics are performed for both a rigid housing configuration and a flexible one. Natural frequencies, dynamic mesh forces, and dynamic bearing reaction loads are computed, and the housing compliance contribution on system dynamic characteristics is analyzed. Results show that increasing housing compliance will decrease the system natural frequencies and will affect the dynamic bearing reaction loads significantly but have very little influence on the dynamic mesh force. Also, the analysis shows that bearing stiffness has significant influence on the degree of housing contribution on system dynamic characteristics.

Vibration behavior optimization of planetary gear sets

Directory of Open Access Journals (Sweden)

Farshad Shakeri Aski

2014-12-01

Full Text Available This paper presents a global optimization method focused on planetary gear vibration reduction by means of tip relief profile modifications. A nonlinear dynamic model is used to study the vibration behavior. In order to investigate the optimal radius and amplitude, Brute Force method optimization is used. One approach in optimization is straightforward and requires considerable computation power: brute force methods try to calculate all possible solutions and decide afterwards which one is the best. Results show the influence of optimal profile on planetary gear vibrations.

Development of a rotary clap mechanism for positive-displacement rotary pumps: Kinematic analysis and working principle

International Nuclear Information System (INIS)

Shim, Sung Bo; Kim, Kyeong Uk; Park, Young Jun; Kim, Jong Mun

2015-01-01

A five-bar spatial mechanism named as a rotary clap mechanism is developed as a pumping device for positive displacement rotary pumps. The mechanism comprises a driving crank, a shaft link with two pins and two gears mounted on the middle and both ends, two rotors with jaws equally spaced along their circumferences, and two fixed internal gears. As the crank rotates, the gear pin-jointed to the crank rotates about the crank pin and at the same time rotates about the center of the fixed internal gears like a hypo-cyclic gear train. The gear-attached shaft link also rotates about the crank pin and about the fixed internal gears at the same time. This motion of the shaft link makes the pins rotate about the center of the fixed internal gears with a periodically varying radius. Therefore, two rotors driven by the pins rotate with different angular velocities. One rotor alternately leads and lags relative to the other rotor. These lead-lag motions between the two jaws of the rotors, which result in suction and discharge required for pumping, resemble hand clapping from which the mechanism was named. Construction and design parameters of the rotary clap mechanism are introduced, and kinematic analysis of this mechanism is performed. The relationships among design parameters, inherent constraints, and effects of design parameters on the is placement of mechanism are also presented.

PARAMETRIC DRAWINGS VS. AUTOLISP

Directory of Open Access Journals (Sweden)

PRUNĂ Liviu

2015-06-01

Full Text Available In this paper the authors make a critical analysis of the advantages offered by the parametric drawing use by comparison with the AutoLISP computer programs used when it comes about the parametric design. Studying and analysing these two work models the authors have got to some ideas and conclusions which should be considered in the moment in that someone must to decide if it is the case to elaborate a software, using the AutoLISP language, or to establish the base rules that must be followed by the drawing, in the idea to construct outlines or blocks which can be used in the projection process.

Projective configurations in projectivegeometrical drawings

Directory of Open Access Journals (Sweden)

Ivashchenko Andrey Viktorovich

2015-05-01

Full Text Available The article focuses on the optimization of the earlier discussed computer method of obtaining new forms of polyhedra based on projective geometry drawings (trace Diagrams.While working on getting new multifaceted forms by projective geometry methods based on the well-known models of polyhedra on the first stage of the work it is required to calculate the parameters of projective geometry drawings, and then to build them. This is an often used apparatus of analytical geometry. According to it, at first the parameters of the polyhedron (core system of planes are calculated, then we obtain the equation of the plane of the face of the polyhedron, and finally we obtain the equations of lines the next plane faces on the selected curve plane. At each stage of application such a method requires the use of the algorithms of floating point arithmetic, on the one hand, leads to some loss of accuracy of the results and, on the other hand, the large amount of computer time to perform these operations in comparison with integer arithmetic operations.The proposed method is based on the laws existing between the lines that make up the drawing - the known configurations of projective geometry (complete quadrilaterals, configuration of Desargues, Pappus et al..The authors discussed in detail the analysis procedure of projective geometry drawing and the presence of full quadrilaterals, Desargues and Pappus configurations in it.Since the composition of these configurations is invariant with respect to projective change of the original nucleus, knowing them, you can avoid the calculations when solving the equations for finding direct projective geometry drawing analytically, getting them on the basis of belonging to a particular configuration. So you can get a definite advantage in accuracy of the results, and in the cost of computer time. Finding these basic configurations significantly enriches the set of methods and the use of projective geometry drawings.

Study on Nonlinear Vibration Analysis of Gear System with Random Parameters

Science.gov (United States)

Tong, Cao; Liu, Xiaoyuan; Fan, Li

2018-03-01

In order to study the dynamic characteristics of gear nonlinear vibration system and the influence of random parameters, firstly, a nonlinear stochastic vibration analysis model of gear 3-DOF is established based on Newton’s Law. And the random response of gear vibration is simulated by stepwise integration method. Secondly, the influence of stochastic parameters such as meshing damping, tooth side gap and excitation frequency on the dynamic response of gear nonlinear system is analyzed by using the stability analysis method such as bifurcation diagram and Lyapunov exponent method. The analysis shows that the stochastic process can not be neglected, which can cause the random bifurcation and chaos of the system response. This study will provide important reference value for vibration engineering designers.

Draw the Line!

DEFF Research Database (Denmark)

present proceedings from the UPGEM conference "Draw the Line!" in Copenhagen May 2008. The proceedings include contributions by UPGEM researchers, conference speeches by other researchers, politicians and gender equality officers in which they relate their work and research with the research done in UPGEM......Draw the Line! International Conference, Copenhagen 2008 Papers, proceedings and recommendations is the second publication of the international three year long project "Understanding Puzzles in the Gendered European Map" (UPGEM), which is financed by the European Commission. In this publication we....... The UPGEM research has previously been published in national reports from each of the partner countries (Denmark, Estonia, Finland, Italy and Poland). In these individual national reports of universities as workplaces for male and female researchers we discuss scientific cultures in physics embedded...

Analysis of dynamic capacity of low-contact-ratio spur gears using Lundberg-Palmgren theory

Science.gov (United States)

Coy, J. J.

1975-01-01

A concise mathematical model is developed for surface fatigue life of low-contact-ratio spur gears. The expected fatigue life of the pinion, gear, or gear sets may be calculated from the model. An equation for the dynamic capacity of the gear set was also derived in terms of the transmitted tangential tooth load which will give a 10-percent fatigue life of one million pinion revolutions. The theoretical life was compared with experimental data for a set of VAR AISI 9310 gears operating at a Hertz stress of 1.71X10 to the 9th power newtons per square meter (248,000 psi) and 10 000 revolutions per minute. Good agreement was obtained between the experimental and theoretical surface fatigue life of the gears.

77 FR 36998 - Proposed Information Collection; Comment Request; Mandatory Shrimp Vessel and Gear...

Science.gov (United States)

2012-06-20

... Collection; Comment Request; Mandatory Shrimp Vessel and Gear Characterization Survey AGENCY: National... under the Shrimp Fishery Management Plan (FMP). The regulations for the Gulf Shrimp Vessel and Gear... and Gear Characterization Form. The form will be provided by NMFS at the time of permit application...

78 FR 40436 - Proposed Information Collection; Comment Request; Mandatory Shrimp Vessel and Gear...

Science.gov (United States)

2013-07-05

... Collection; Comment Request; Mandatory Shrimp Vessel and Gear Characterization Survey AGENCY: National... under the Shrimp Fishery Management Plan (FMP). The regulations for the Gulf Shrimp Vessel and Gear... Gear Characterization Form. The form will be provided by NMFS at the time of permit application and...

Improvement in surface fatigue life of hardened gears by high-intensity shot peening

Science.gov (United States)

Townsend, Dennis P.

1992-04-01

Two groups of carburized, hardened, and ground spur gears that were manufactured from the same heat vacuum induction melted vacuum arc melted (VIM VAR) AISI 9310 steel were endurance tested for surface fatigue. Both groups were manufactured with a standard ground 16 rms surface finish. One group was subjected to a shot peening (SP) intensity of 7 to 9A, and the second group was subjected to a SP intensity of 15 to 17A. All gears were honed after SP to a surface finish of 16 rms. The gear pitch diameter was 8.89 cm. Test conditions were a maximum Hertz stress of 1.71 GPa, a gear temperature of 350 K, and a speed of 10000 rpm. The lubricant used for the tests was a synthetic paraffinic oil with an additive package. The following results were obtained: The 10 pct. surface fatigue (pitting) life of the high intensity (15 to 17A) SPed gears was 2.15 times that of the medium intensity (7 to 9A) SPed gears, the same as that calculated from measured residual stress at a depth of 127 microns. The measured residual stress for the high intensity SPed gears was 57 pct. higher than that for the medium intensity SPed gears at a depth of 127 microns and 540 pct. higher at a depth of 51 microns.

ACCURACY RESEARCH OF THE DIAMETRICAL SIZES FORMING AT GEAR SHAPING BY STEPPED CUTTER

Directory of Open Access Journals (Sweden)

N. M. Rasulov

2015-09-01

Full Text Available The paper presents research results of forming accuracy for diametrical sizes at gear shaping with stepped cutter and the traditional method. Analysis of static technological dimensional pitch size chain of wheels being cut is performed. It was revealed that the most of transmission errors of the wheels, formed by the traditional gear-shaped cutter are caused by manufacturing and installation error of the cutter and result from the formation of each tooth of the wheel with a certain tool. This is not the case with gear shaping by step cutter since at that, the profiles of all gear teeth are formed by means of tooth profile mostly remote from the tool rotation axis. Analysis of occurrence of setting-up errors typical for the above gear shaping methods has been performed. At gear shaping with stepped cutter there are no setting-up error components. It was revealed that this fact causes the absence of errors in the tool position before its each double motion. The accuracy of diametrical sizes increases. Formation mechanism of tool installation errors and workpiece are also given and their analysis is presented. Findings in the field of gear shaping with stepped cutter comply with results of research carried out by the other authors in the field of traditional gear shaping.

Comparison of wavelet based denoising schemes for gear condition monitoring: An Artificial Neural Network based Approach

Science.gov (United States)

Ahmed, Rounaq; Srinivasa Pai, P.; Sriram, N. S.; Bhat, Vasudeva

2018-02-01

Vibration Analysis has been extensively used in recent past for gear fault diagnosis. The vibration signals extracted is usually contaminated with noise and may lead to wrong interpretation of results. The denoising of extracted vibration signals helps the fault diagnosis by giving meaningful results. Wavelet Transform (WT) increases signal to noise ratio (SNR), reduces root mean square error (RMSE) and is effective to denoise the gear vibration signals. The extracted signals have to be denoised by selecting a proper denoising scheme in order to prevent the loss of signal information along with noise. An approach has been made in this work to show the effectiveness of Principal Component Analysis (PCA) to denoise gear vibration signal. In this regard three selected wavelet based denoising schemes namely PCA, Empirical Mode Decomposition (EMD), Neighcoeff Coefficient (NC), has been compared with Adaptive Threshold (AT) an extensively used wavelet based denoising scheme for gear vibration signal. The vibration signals acquired from a customized gear test rig were denoised by above mentioned four denoising schemes. The fault identification capability as well as SNR, Kurtosis and RMSE for the four denoising schemes have been compared. Features extracted from the denoised signals have been used to train and test artificial neural network (ANN) models. The performances of the four denoising schemes have been evaluated based on the performance of the ANN models. The best denoising scheme has been identified, based on the classification accuracy results. PCA is effective in all the regards as a best denoising scheme.

The Selected Problems of Studies of Aircraft Landing Gear

Directory of Open Access Journals (Sweden)

Rośkowicz Marek

2016-12-01

Full Text Available The article portrays the results of experimental studies conducted in the field of static strength test of main landing gear of lightweight aircraft as well as in the area of establishing the pneumatic tyre characteristics of main landing gear. The studies were carried out in compliance with methodologies of performing studies for the purposes of solutions implemented in aviation structures. It was stated that static strength tests of landing gear should not be done with the use of shock absorbers, due to the fact that this element, distinguished by high viscoelastic properties, by being statically loaded, is subject to displacements that do not occur during normal operation of the aircraft. Excessive displacements of shock absorber result in the load distribution in other landing gear elements being incompatible with project assumptions, which in turn leads to this strength test being interrupted, bearing in mind significantly lower loads than anticipated. It was also concluded that in order to determine pneumatic tyre characteristics it is not necessary to carry out tests on the whole landing gear strut, because the results obtained in the compression test of the wheel itself with pneumatic tyre are identical as the results acquired during tests conducted in accordance with methodology. Test preparation process with the use of the wheel itself and its realization is less time-consuming, less expensive and does not entail the necessity to build complex test stands.

THE IMPACT OF THE ELEVATOR GUIDES CONTAMINATION ON THE BRAKING PROCESS DELAY FOR SELECTED PROGRESSIVE GEARS

Directory of Open Access Journals (Sweden)

Rafał Longwic

2017-06-01

Full Text Available The authors’ tests results on the impact of the guiding system (the guides contamination in the friction lift on the delay of progressive gears braking process are presented in this article. The tests were conducted using a free fall method and a test bench built for that purpose. In order to render all working conditions the guiding system of tested gears was lubricated with the most commonly used lubricating agents. Solid grease (SM, mineral oil (OL, the mixture of solid grease and quartz sand (S50 as well as the mixture of mineral oil and quartz sand (O50 were used.

COMPUTER-AIDED DESIGN, MANUFACTURE AND EXPERIMENTAL ANALYSIS OF A PAIR OF ELLIPTICAL SPUR GEARS

Directory of Open Access Journals (Sweden)

Mehmet YAZAR

2016-12-01

Full Text Available ABSTRACT In this study, geometrical equations of elliptical spur gears, which are too difficult to manufacture by traditional methods and which require specific machines equipped with special techniques, are developed using the methods in the literature. Using these equations, a LISP program on AutoLISP is created to model elliptical spur gears on AutoCAD with desired tooth number and modules. Elliptical spur gears are manufactured with 5 different modules by Wire EDM through the above-mentioned package program. The variations in the center distances of elliptical spur gears, the most important parameter for workability of gears, are experimentally determined by a simple test unit designed and manufactured within the context this study. In addition, the surface roughness and hardness of elliptical spur gears are obtained and hydraulic pump and noise analysis results are discussed. The experimental and computer-aided results show that the elliptical spur gears may widely be used in many industrial and mechanical applications in the future.

Dynamic analysis of spiral bevel and hypoid gears with high-order transmission errors

Science.gov (United States)

Yang, J. J.; Shi, Z. H.; Zhang, H.; Li, T. X.; Nie, S. W.; Wei, B. Y.

2018-03-01

A new gear surface modification methodology based on curvature synthesis is proposed in this study to improve the transmission performance. The generated high-order transmission error (TE) for spiral bevel and hypoid gears is proved to reduce the vibration of geared-rotor system. The method is comprised of the following steps: Firstly, the fully conjugate gear surfaces with pinion flank modified according to the predesigned relative transmission movement are established based on curvature correction. Secondly, a 14-DOF geared-rotor system model considering backlash nonlinearity is used to evaluate the effect of different orders of TE on the dynamic performance a hypoid gear transmission system. For case study, numerical simulation is performed to illustrate the dynamic response of hypoid gear pair with parabolic, fourth-order and sixth-order transmission error derived. The results show that the parabolic TE curve has higher peak to peak amplitude compared to the other two types of TE. Thus, the excited dynamic response also shows larger amplitude at response peaks. Dynamic responses excited by fourth and sixth order TE also demonstrate distinct response components due to their different TE period which is expected to generate different sound quality or other acoustic characteristics.

Nonlinear Dynamic Analysis and Optimization of Closed-Form Planetary Gear System

Directory of Open Access Journals (Sweden)

Qilin Huang

2013-01-01

Full Text Available A nonlinear purely rotational dynamic model of a multistage closed-form planetary gear set formed by two simple planetary stages is proposed in this study. The model includes time-varying mesh stiffness, excitation fluctuation and gear backlash nonlinearities. The nonlinear differential equations of motion are solved numerically using variable step-size Runge-Kutta. In order to obtain function expression of optimization objective, the nonlinear differential equations of motion are solved analytically using harmonic balance method (HBM. Based on the analytical solution of dynamic equations, the optimization mathematical model which aims at minimizing the vibration displacement of the low-speed carrier and the total mass of the gear transmission system is established. The optimization toolbox in MATLAB program is adopted to obtain the optimal solution. A case is studied to demonstrate the effectiveness of the dynamic model and the optimization method. The results show that the dynamic properties of the closed-form planetary gear transmission system have been improved and the total mass of the gear set has been decreased significantly.

Quantification of Gear Tooth Damage by Optimal Tracking of Vibration Signatures

Science.gov (United States)

Choy, F. K.; Veillette, R. J.; Polyshchuk, V.; Braun, M. J.; Hendricks, R. C.

1996-01-01

This paper presents a technique for quantifying the wear or damage of gear teeth in a transmission system. The procedure developed in this study can be applied as a part of either an onboard machine health-monitoring system or a health diagnostic system used during regular maintenance. As the developed methodology is based on analysis of gearbox vibration under normal operating conditions, no shutdown or special modification of operating parameters is required during the diagnostic process. The process of quantifying the wear or damage of gear teeth requires a set of measured vibration data and a model of the gear mesh dynamics. An optimization problem is formulated to determine the profile of a time-varying mesh stiffness parameter for which the model output approximates the measured data. The resulting stiffness profile is then related to the level of gear tooth wear or damage. The procedure was applied to a data set generated artificially and to another obtained experimentally from a spiral bevel gear test rig. The results demonstrate the utility of the procedure as part of an overall health-monitoring system.

Thinking Drawing

Science.gov (United States)

Adams, Eileen

2017-01-01

This article draws heavily on the author's critical autobiography: "Eileen Adams: Agent of Change." It presents evidence of the value of drawing as a medium for learning, particularly in art and design, and argues that drawing is a useful educational tool. The premise is that drawing makes you think. This article explains various…

ARTIFICIAL NEURAL NETWORKS BASED GEARS MATERIAL SELECTION HYBRID INTELLIGENT SYSTEM

Institute of Scientific and Technical Information of China (English)

X.C. Li; W.X. Zhu; G. Chen; D.S. Mei; J. Zhang; K.M. Chen

2003-01-01

An artificial neural networks(ANNs) based gear material selection hybrid intelligent system is established by analyzing the individual advantages and weakness of expert system (ES) and ANNs and the applications in material select of them. The system mainly consists of tow parts: ES and ANNs. By being trained with much data samples,the back propagation (BP) ANN gets the knowledge of gear materials selection, and is able to inference according to user input. The system realizes the complementing of ANNs and ES. Using this system, engineers without materials selection experience can conveniently deal with gear materials selection.

Estimation of seafloor impact from demersal trawls, seines and dredges based on gear design and dimensions

DEFF Research Database (Denmark)

Eigaard, Ole Ritzau; Bastardie, Francois; Breen, Michael

a different approach using the gear itself (design and dimensions) for understanding and estimation of the physical interactions with the seafloor at the individual fishing operation level. With reference to the métier groupings of EU logbooks, we defined 17 distinct towed gear groups in European waters (11...... otter trawl groups, 3 beam trawl groups, 2 demersal seine groups, and 1 dredge group), for which we established seafloor “footprints”. The footprint of a gear was defined as the relative contribution from individual larger gear components, such as the trawl doors, sweeps and ground gear, to the total...... types based on a review of the scientific literature. For each defined gear group a vessel-size (kW or total length) – gear size (total gear width or circumference) relationship was estimated to enable the prediction of gear footprint area and sediment penetration from vessel size. The implications...

Effects on Diagnostic Parameters After Removing Additional Synchronous Gear Meshes

Science.gov (United States)

Decker, Harry J.

2003-01-01

Gear cracks are typically difficult to diagnose with sufficient time before catastrophic damage occurs. Significant damage must be present before algorithms appear to be able to detect the damage. Frequently there are multiple gear meshes on a single shaft. Since they are all synchronous with the shaft frequency, the commonly used synchronous averaging technique is ineffective in removing other gear mesh effects. Carefully applying a filter to these extraneous gear mesh frequencies can reduce the overall vibration signal and increase the accuracy of commonly used vibration metrics. The vibration signals from three seeded fault tests were analyzed using this filtering procedure. Both the filtered and unfiltered vibration signals were then analyzed using commonly used fault detection metrics and compared. The tests were conducted on aerospace quality spur gears in a test rig. The tests were conducted at speeds ranging from 2500 to 5000 revolutions per minute and torques from 184 to 228 percent of design load. The inability to detect these cracks with high confidence results from the high loading which is causing fast fracture as opposed to stable crack growth. The results indicate that these techniques do not currently produce an indication of damage that significantly exceeds experimental scatter.

Estimating seabed pressure from demersal trawls, seines, and dredges based on gear design and dimensions

DEFF Research Database (Denmark)

Eigaard, Ole Ritzau; Bastardie, Francois; Breen, Mike

2016-01-01

such as logbook data. Here, we take a different approach starting from the gear itself (design and dimensions) to estimate the physical interactions with the seabed at the level of the individual fishing operation. We defined 14 distinct towed gear groups in European waters (eight otter trawl groups, three beam...... trawl groups, two demersal seine groups, and one dredge group), for which we established gear “footprints”. The footprint of a gear is defined as the relative contribution from individual larger gear components, such as trawl doors, sweeps, and groundgear, to the total area and severity of the gear...... to enable the prediction of gear footprint area and sediment penetration from vessel size. Application of these relationships with average vessel sizes and towing speeds provided hourly swept-area estimates by métier. Scottish seining has the largest overall gear footprint of ∼1.6 km2 h−1 of which 0.08 km2...

Shifting Kenya's Private Sector into Higher Gear : A Trade and Competitiveness Agenda

OpenAIRE

World Bank Group

2016-01-01

Shifting Kenya’s private sector into higher gear: a trade and competitiveness agenda’ was born out of the World Bank’s Trade and Competitiveness (T&C) Global Practice recent stock taking of its work in Kenya. This was part of a Programmatic Approach that aimed to organize T&C’s knowledge, advisory, and convening services to address Kenya’s development challenges in the private sector space...

Landing Gear Noise Prediction and Analysis for Tube-and-Wing and Hybrid-Wing-Body Aircraft

Science.gov (United States)

Guo, Yueping; Burley, Casey L.; Thomas, Russell H.

2016-01-01

Improvements and extensions to landing gear noise prediction methods are developed. New features include installation effects such as reflection from the aircraft, gear truck angle effect, local flow calculation at the landing gear locations, gear size effect, and directivity for various gear designs. These new features have not only significantly improved the accuracy and robustness of the prediction tools, but also have enabled applications to unconventional aircraft designs and installations. Systematic validations of the improved prediction capability are then presented, including parametric validations in functional trends as well as validations in absolute amplitudes, covering a wide variety of landing gear designs, sizes, and testing conditions. The new method is then applied to selected concept aircraft configurations in the portfolio of the NASA Environmentally Responsible Aviation Project envisioned for the timeframe of 2025. The landing gear noise levels are on the order of 2 to 4 dB higher than previously reported predictions due to increased fidelity in accounting for installation effects and gear design details. With the new method, it is now possible to reveal and assess the unique noise characteristics of landing gear systems for each type of aircraft. To address the inevitable uncertainties in predictions of landing gear noise models for future aircraft, an uncertainty analysis is given, using the method of Monte Carlo simulation. The standard deviation of the uncertainty in predicting the absolute level of landing gear noise is quantified and determined to be 1.4 EPNL dB.

Dynamic Analysis of Helical Planetary Gear Sets under Combined Force and Moment Loading

Directory of Open Access Journals (Sweden)

Yanfang Liu

2017-01-01

Full Text Available The dynamic behavior of a single-stage planetary gear set with helical gears of multishaft automotive automatic transmissions has been studied, in which one component of the planetary gear set is imposed by additional external vertical and axial loading from countershaft gear pair in addition to the moment. Under these combined loading conditions, the contributions of the deflections of the ring gear and the carrier cannot be neglected. A three-dimensional nonlinear time-variant dynamic model considering not only the transverse, torsional, axial, and rotational motions of the gears but also the elasticity of the mounted shafts has been developed by combining the lumped parameter method with finite element method. The natural modes and the forced vibration responses due to static transmission errors have been obtained. The proposed dynamic model is employed to describe the effects of the combined external loading condition and positioning on the dynamic behavior of a four-planet system.

Flow-Field Investigation of Gear-Flap Interaction on a Gulfstream Aircraft Model

Science.gov (United States)

Yao, Chung-Sheng; Jenkins, Luther N.; Bartram, Scott M.; Harris, Jerome; Khorrami, Mehdi R.; Mace, W. Derry

2014-01-01

Off-surface flow measurements of a high-fidelity 18% scale Gulfstream aircraft model in landing configuration with the main landing gear deployed are presented. Particle Image Velocimetry (PIV) and Laser Velocimetry (LV) were used to measure instantaneous velocities in the immediate vicinity of the main landing gear and its wake and near the inboard tip of the flap. These measurements were made during the third entry of a series of tests conducted in the NASA Langley Research Center (LaRC) 14- by 22-Foot Subsonic Tunnel (14 x 22) to obtain a comprehensive set of aeroacoustic measurements consisting of both aerodynamic and acoustic data. The majority of the off-body measurements were obtained at a freestream Mach number of 0.2, angle of attack of 3 degrees, and flap deflection angle of 39 degrees with the landing gear on. A limited amount of data was acquired with the landing gear off. LV was used to measure the velocity field in two planes upstream of the landing gear and to measure two velocity profiles in the landing gear wake. Stereo and 2-D PIV were used to measure the velocity field over a region extending from upstream of the landing gear to downstream of the flap trailing edge. Using a special traverse system installed under the tunnel floor, the velocity field was measured at 92 locations to obtain a comprehensive picture of the pertinent flow features and characteristics. The results clearly show distinct structures in the wake that can be associated with specific components on the landing gear and give insight into how the wake is entrained by the vortex at the inboard tip of the flap.

75 FR 12462 - Fisheries of the Northeastern United States; Northeast Multispecies Fishery; Removal of Gear...

Science.gov (United States)

2010-03-16

...; Removal of Gear Restriction for the U.S./Canada Management Area AGENCY: National Marine Fisheries Service...; removal of gear restrictions. SUMMARY: This action removes temporary gear restrictions in both the Eastern... Management Act (Magnuson- Stevens Act). DATES: Removal of the temporary gear restriction in the Western U.S...

A natural driven membrane process for brackish and wastewater treatment: photovoltaic powered ED and FO hybrid system.

Science.gov (United States)

Zhang, Yang; Pinoy, Luc; Meesschaert, Boudewijn; Van der Bruggen, Bart

2013-09-17

In isolated locations, remote areas, or islands, potable water is precious because of the lack of drinking water treatment facilities and energy supply. Thus, a robust and reliable water treatment system based on natural energy is needed to reuse wastewater or to desalinate groundwater/seawater for provision of drinking water. In this work, a hybrid membrane system combining electrodialysis (ED) and forward osmosis (FO), driven by renewable energy (solar energy), denoted as EDFORD (ED-FO Renewable energy Desalination), is proposed to produce high-quality water (potable) from secondary wastewater effluent or brackish water. In this hybrid membrane system, feedwater (secondary wastewater effluent or synthetic brackish water) was drawn to the FO draw solution while the organic and inorganic substances (ions, compounds, colloids and particles) were rejected. The diluted draw solution was then pumped to the solar energy driven ED. In the ED unit, the diluted draw solution was desalted and high-quality water was produced; the concentrate was recycled to the FO unit and reused as the draw solution. Results show that the water produced from this system contains a low concentration of total organic carbon (TOC), carbonate, and cations derived from the feedwater; had a low conductivity; and meets potable water standards. The water production cost considering the investment for membranes and solar panel is 3.32 to 4.92 EUR m(-3) (for 300 days of production per year) for a small size potable water production system.

A Procedure for 3-D Contact Stress Analysis of Spiral Bevel Gears

Science.gov (United States)

Kumar, A.; Bibel, G.

1994-01-01

Contact stress distribution of spiral bevel gears using nonlinear finite element static analysis is presented. Procedures have been developed to solve the nonlinear equations that identify the gear and pinion surface coordinates based on the kinematics of the cutting process and orientate the pinion and the gear in space to mesh with each other. Contact is simulated by connecting GAP elements along the intersection of a line from each pinion point (parallel to the normal at the contact point) with the gear surface. A three dimensional model with four gear teeth and three pinion teeth is used to determine the contact stresses at two different contact positions in a spiral bevel gearset. A summary of the elliptical contact stress distribution is given. This information will be helpful to helicopter and aircraft transmission designers who need to minimize weight of the transmission and maximize reliability.

75 FR 55301 - Proposed Information Collection; Comment Request; Northeast Region Gear Identification Requirements

Science.gov (United States)

2010-09-10

...., buoys, radar reflectors, or other methods identified in the regulations). The number of gear in the case... be responsible for marking several strings of a given type of gear, or may use multiple different gear types that require marking for identification and visibility. The display of the identifying...

Worm gearing for valve automation; Schneckengetriebe fuer die Armaturenautomatisierung

Energy Technology Data Exchange (ETDEWEB)

Herbstritt, Michael [AUMA Riester GmbH und Co. KG, Muellheim (Germany)

2010-11-15

Part-turn gearboxes are indispensable for exertion of the torques necessary for large part-turn valves. Torque demand has increased in the past decade, as a result, for example, of the use of pipelines of ever greater diameters in large conurbations, and of the operation of such pipelines at ever higher pressures. The design principle of a worm gear is useful in this context. Worm gearing systems with initial torques of up to 675,000 Nm are now available. The design of gearing systems capable of handling forces of this magnitude necessitates great know-how and experience. The very maximum of reliability is a basic requirement for actuator systems for applications involving such dimensions, since a failure may have catastrophic consequences. (orig.)

Vorticity amplification and its effects on flow separation from simplified landing gear wheels

Science.gov (United States)

McCarthy, Philip; Feltham, Graham; Ekmekci, Alis

2015-11-01

In the presence of weak streams of inbound vorticity, the stagnation region of bluff bodies have been shown to support mechanisms for the collection and amplification of said vorticity into large-scale, discrete vortex structures. For extremely low aspect ratio cylinders, such as those which represent simplified aircraft landing gear wheels, these discrete vortex structures tilt around the sides of the geometry, orientating their axes in the streamwise direction. Once the oncoming vorticity is collected and amplified into discrete vortices, they are shed from the stagnation region and this cycle repeats itself periodically. The present work investigates the effect of the vortex tilting and subsequent shedding on the behaviour of the outboard side flow separation region present on simplified landing gear wheels. Experiments were conducted in a recirculating-type water tunnel on a two-wheel landing gear model, with the upstream vorticity source being a 100 µm platinum wire. Hydrogen bubble visualisations were first used for qualitative understanding of the flow, accompanied by 2D-PIV for vortex identification and tracking of the growth and movement of the observed structures. Finally, the side separation bubble has been characterised using 3D velocity measurements (using V3V). The authors would like to thank Bombardier, Messier-Bugatti-Dowty and NSERC for their support for this project.

Practical disinfection chemicals for fishing and crayfishing gear against crayfish plague transfer

Directory of Open Access Journals (Sweden)

Jussila J.

2014-01-01

Full Text Available We tested four commercial disinfectants against crayfish plague (Aphanomyces astaci spores in both aquatic solutions and with material mimicking fishing and crayfishing gear, e.g. traps, ropes, mesh, etc. The tested disinfectants were Proxitane®5:14, Proxitane®12:20, Wofasteril®E400, Virkon®S and hydrogen peroxide. The effects of the chemicals were initially tested in liquid zoospore cultures and the effective concentrations were then further tested using clean and dirty model materials (PP sheet, nylon rope, cotton fabric contaminated with A. astaci spore solutions. The disinfectants effective against infective crayfish plague spores with both clean and dirty model materials were Proxinate®5:14 (effective concentration was 30 mg·L-1 of PAA and Virkon®S (3 g·L-1, while Proxinate®12:20 (10 mg·L-1 of PAA and Wofasteril®E400 (30 mg·L-1 of PAA worked only with clean model materials. Hydrogen peroxide was not effective in the tested concentrations and conditions. Based on the results, the disinfectants most suitable for the fishing and crayfishing gear disinfection would be Proxitane®5:14 and Virkon®S, with the condition that all the gear should be thoroughly cleaned of organic matter to ensure inactivation of A. astaci spores.

Integrating Oil Debris and Vibration Gear Damage Detection Technologies Using Fuzzy Logic

Science.gov (United States)

Dempsey, Paula J.; Afjeh, Abdollah A.

2002-01-01

A diagnostic tool for detecting damage to spur gears was developed. Two different measurement technologies, wear debris analysis and vibration, were integrated into a health monitoring system for detecting surface fatigue pitting damage on gears. This integrated system showed improved detection and decision-making capabilities as compared to using individual measurement technologies. This diagnostic tool was developed and evaluated experimentally by collecting vibration and oil debris data from fatigue tests performed in the NASA Glenn Spur Gear Fatigue Test Rig. Experimental data were collected during experiments performed in this test rig with and without pitting. Results show combining the two measurement technologies improves the detection of pitting damage on spur gears.

Factors that determine development of the ability to draw

Directory of Open Access Journals (Sweden)

Jorge Luis Dahik Cabrera

2016-03-01

Full Text Available In this investigation, the necessary factors are determined to structure a drawing representing an object, a brief description of the functions of the cerebral hemispheres, the theory of multiple bits of intelligence Gardner, capacities of representation and perception involved in the skill is reviewed and ability to draw. This work aims to be the beginning of a larger study, where they plan to measure the ability to draw in students, in order to experiment with alternative methodologies for teaching drawing.

75 FR 58373 - Gaining Early Awareness and Readiness for Undergraduate Programs (GEAR UP)

Science.gov (United States)

2010-09-24

... Readiness for Undergraduate Programs (GEAR UP) AGENCY: Office of Postsecondary Education, Department of Education. ACTION: Notice of intent to fund down the fiscal year (FY) 2008 grant slate for the GEAR UP Program. SUMMARY: The Secretary intends to use the grant slate developed in FY 2008 for the GEAR UP...

Subcriticality of accelerator driven system by AESJ/JAERI working party

International Nuclear Information System (INIS)

Iwasaki, Tomohiko

2002-01-01

Under Atomic Energy Society of Japan (AESJ) and Japan Atomic Energy Research Institute (JAERI), a Working Party on Reactor Physics of Accelerator-Driven System (ADS-WP) has been set since March 1999 to review and investigate special subjects related to reactor physics research of Accelerator-Driven System (ADS). In the ADS-WP, the extensive and aggressive activity is being made by 25 professional members in the field of reactor physics in Japan. The ADS is now studying three subjects related to subcriticality of ADS; (1) calculation accuracy of subcriticality on ADS, (2) critical safety issues of ADS, and (3) theoretical review of subcriticality and its measurement methods. This paper describes two topics related to the subjects (1) and (2); one is an analysis of maximum reactivity potentially inserted to a subcritical core and the other is a benchmark proposal for checking calculation accuracy of subcriticality on ADS. The full specification of the calculation benchmark will be supplied by June 2002. Researchers from overseas, especially from Korea, are welcome to join this benchmark

Research on the dynamic response of high-contact-ratio spur gears influenced by surface roughness under EHL condition

Science.gov (United States)

Kang, Huang; Xiong, Yangshou; Wang, Tao; Chen, Qi

2017-01-01

Employing high-contact-ratio (HCR) gear is an effective method of decreasing the load on a single tooth, as well as reducing vibration and noise. While the spindlier tooth leads to greater relative sliding, having more teeth participate in contact at the same time makes the HCR gear more sensitive to the surface quality. Available literature regarding HCR gear primarily investigates the geometrical optimization, load distribution, or efficiency calculation. Limited work has been conducted on the effect of rough surfaces on the dynamic performance of HCR gear. For this reason, a multi-degree-of-freedom (MDOF) model is presented mathematically to characterize the static transmission error based on fractal theory, investigate the relative sliding friction using an EHL-based friction coefficient formula, and detail the time-varying friction coefficient suitable for HCR gear. Based on numerical results, the surface roughness has little influence on system response in terms of the dynamic transmission error but has a large effect on the motion in off-line-of-action (OLOA) direction and friction force. The impact of shaft-bearing stiffness and damping ratio is also explored with results revealing that a greater shaft-bearing stiffness is beneficial in obtaining a more stable motion in OLOA direction, and a larger damping ratio results in a smaller effective friction force. The theory presented in this report outlines a new method of analyzing the dynamics of HCR gear in respect of introducing surface roughness into MDOF model directly, as well as establishing an indirect relationship between dynamic responses and surface roughness. This method is expected to guide surface roughness design and manufacturing in the future.

The contact drag of towed demersal fishing gear components

Science.gov (United States)

O'Neill, F. G.; Summerbell, K.; Ivanović, A.

2018-01-01

The contact demersal towed fishing gears make with the seabed can lead to penetration of the substrate, lateral displacement of the sediment and a pressure field transmitted through the sediment. It will also contribute to the overall drag of the fishing gear. Consequently, there can be environmental effects such as habitat alteration and benthic mortality, and impacts to the fuel efficiency of the fishing operation which will affect emissions of nitrogen oxides, sulphur oxides and greenhouse gases such as CO2. Here we present the results of experimental trials that measure the contact drag of a range of elements that represent some of the components of towed demersal gears that are in contact with the seabed. We show that the contact drag of the gear components depends on their weight, geometry, the type of sediment on which they are towed and whether they are rolling or not. As expected, the contact drag of each gear component increases as its weight increases and the drag of fixed elements is greater than that of the rolling ones. The dependence on aspect ratio is more complex and the drag (per unit area) of narrow cylinders is less than that of wider ones when they roll on the finer sediment or are fixed (not permitted to roll) on the coarser sediment. When they roll on the coarse sediment there is no dependence on aspect ratio. Our results also suggest that fixed components may penetrate the seabed to a lesser depth when they are towed at higher speeds but when they roll there is no such relationship.

Evaluation of a vibration diagnostic system for the detection of spur gear pitting failures

Science.gov (United States)

Townsend, Dennis P.; Zakrajsek, James J.

1993-01-01

A vibration diagnostic system was used to detect spur gear surface pitting fatigue in a closed-loop spur gear fatigue test rig. The diagnostic system, comprising a personal computer with an analog-to-digital conversion board, a diagnostic system unit, and software, uses time-synchronous averaging of the vibration signal to produce a vibration image of each tooth on any gear in a transmission. Several parameters were analyzed including gear pair stress wave and raw baseband vibration, kurtosis, peak ratios, and others. The system provides limits for the various parameters and gives a warning when the limits are exceeded. Several spur gear tests were conducted with this system and vibration data analyzed at 5-min. intervals. The results presented herein show that the system is fairly effective at detecting spur gear tooth surface fatigue pitting failures.

Induction heating of gears - pulsing dual-frequency concept

Directory of Open Access Journals (Sweden)

R. Przyłucki

2013-04-01

Full Text Available The paper concerns analysis of gears hardening process. In order to obtain required temperature distribution several variations of single and combined frequencies for selected gear-wheel configurations were considered. The paper includes the calculation models and analysis of geometry and current intensity as well frequency influence on temperature distribution of the tooth surface. All calculations have been carried out by means of the use of Flux3D simulation program, which enables to provide, coupled electromagnetic and temperature fields analysis.

Distribution of Microstructure and Vickers Hardness in Spur Bevel Gear Formed by Cold Rotary Forging

Directory of Open Access Journals (Sweden)

Wuhao Zhuang

2014-11-01

Full Text Available Cold rotary forging is a novel metal forming technology which is widely used to produce the high performance gears. Investigating the microstructure and mechanical property of cold rotary forged gears has a great significance in improving their service performance. In this study, the grain morphology in different regions of the spur bevel gear which is processed by cold rotary forging is presented. And the distribution regulars of the grain deformation and Vickers hardness in the transverse and axial sections of the gear tooth are studied experimentally. A three-dimensional rigid-plastic FE model is developed to simulate the cold rotary forging process of a spur bevel gear under the DEFORM-3D software environment. The variation of effective strain in the spur bevel gear has been investigated so as to explain the distribution regulars of the microstructure and Vickers hardness. The results of this research thoroughly reveal the inhomogeneous deformation mechanisms in cold rotary forging of spur bevel gears and provide valuable guidelines for improving the performance of cold rotary forged spur bevel gears.

Sea Turtle Human/Gear Interactions Data

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Fisheries Science Center Mississippi Laboratories is responsible for new gear development and testing to reduce bycatch and incidental interactions of...

Tooth Fracture Detection in Spiral Bevel Gears System by Harmonic Response Based on Finite Element Method

Directory of Open Access Journals (Sweden)

Yuan Chen

2017-01-01

Full Text Available Spiral bevel gears occupy several advantages such as high contact ratio, strong carrying capacity, and smooth operation, which become one of the most widely used components in high-speed stage of the aeronautical transmission system. Its dynamic characteristics are addressed by many scholars. However, spiral bevel gears, especially tooth fracture occurrence and monitoring, are not to be investigated, according to the limited published issues. Therefore, this paper establishes a three-dimensional model and finite element model of the Gleason spiral bevel gear pair. The model considers the effect of tooth root fracture on the system due to fatigue. Finite element method is used to compute the mesh generation, set the boundary condition, and carry out the dynamic load. The harmonic response spectra of the base under tooth fracture are calculated and the influence of main parameters on monitoring failure is investigated as well. The results show that the change of torque affects insignificantly the determination of whether or not the system has tooth fracture. The intermediate frequency interval (200 Hz–1000 Hz is the best interval to judge tooth fracture occurrence. The best fault test region is located in the working area where the system is going through meshing. The simulation calculation provides a theoretical reference for spiral bevel gear system test and fault diagnosis.

Analysis of 3D printing parameters of gears for hybrid manufacturing

Science.gov (United States)

Budzik, Grzegorz; Przeszlowski, Łukasz; Wieczorowski, Michal; Rzucidlo, Arkadiusz; Gapinski, Bartosz; Krolczyk, Grzegorz

2018-05-01

The paper deals with analysis and selection of parameters of rapid prototyping of gears by selective sintering of metal powders. Presented results show wide spectrum of application of RP systems in manufacturing processes of machine elements, basing on analysis of market in term of application of additive manufacturing technology in different sectors of industry. Considerable growth of these methods over the past years can be observed. The characteristic errors of printed model with respect to ideal one for each technique were pointed out. Special attention was paid to the method of preparation of numerical data CAD/STL/RP. Moreover the analysis of manufacturing processes of gear type elements was presented. The tested gears were modeled with different allowances for final machining and made by DMLS. Metallographic analysis and strength tests on prepared specimens were performed. The above mentioned analysis and tests were used to compare the real properties of material with the nominal ones. To improve the quality of surface after sintering the gears were subjected to final machining. The analysis of geometry of gears after hybrid manufacturing method was performed (fig.1). The manufacturing process was defined in a traditional way as well as with the aid of modern manufacturing techniques. Methodology and obtained results can be used for other machine elements than gears and constitutes the general theory of production processes in rapid prototyping methods as well as in designing and implementation of production.

76 FR 5402 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Gear...

Science.gov (United States)

2011-01-31

... for OMB Review; Comment Request; Gear Certification ACTION: Notice. SUMMARY: The Department of Labor...) sponsored information collection request (ICR) titled, ``Gear Certification,'' to the Office of Management... cranes, derricks, and accessory gear used in the longshoring, marine terminal, and shipyard industries...

Enhancing Architectural Drawings and Models with Photoshop

CERN Document Server

Onstott, Scott

2010-01-01

Transform your CAD drawings into powerful presentationThis one-of-a-kind book shows you how to use Photoshop to turn CAD drawings and BIM models into artistic presentations with captivating animations, videos, and dynamic 3D imagery. The techniques apply to all leading architectural design software including AutoCAD, Revit, and 3ds Max Design. Video tutorials on the DVD improve your learning curve and let you compare your work with the author's.Turn CAD drawings and BIM models into powerful presentations featuring animation, videos, and 3D imagery for enhanced client appealCraft interactive pa

Using Drawings in Play Therapy: A Jungian Approach

Science.gov (United States)

Birch, Jennifer; Carmichael, Karla D.

2009-01-01

Counselors working with children employ a variety of therapeutic techniques and tools from various theoretical models. One of these tools, drawing, is increasingly being implemented into play therapy. The purpose of this paper is to briefly review Jungian theoretical approaches as they pertain to drawing techniques within the counseling session.

Dismantling the Built Drawing: Working with Mood in Architectural Design

Science.gov (United States)

Teal, Randall

2010-01-01

From the late Middle Ages onward an emphasis on the rational and the technical aspects of design and design drawing gained hold of architectural practice. In this transformation, the phenomenon of mood has been frequently overlooked or seen as something to be added on to a design; yet the fundamental grounding of mood, as described in Martin…

Comparison of analysis and experiment for dynamics of low-contact-ratio spur gears

Science.gov (United States)

Oswald, Fred B.; Rebbechi, Brian; Zakrajsek, James J.; Townsend, Dennis P.; Lin, Hsiang Hsi

1991-01-01

Low-contact-ratio spur gears were tested in NASA gear-noise-rig to study gear dynamics including dynamic load, tooth bending stress, vibration, and noise. The experimental results were compared with a NASA gear dynamics code to validate the code as a design tool for predicting transmission vibration and noise. Analytical predictions and experimental data for gear-tooth dynamic loads and tooth-root bending stress were compared at 28 operating conditions. Strain gage data were used to compute the normal load between meshing teeth and the bending stress at the tooth root for direct comparison with the analysis. The computed and measured waveforms for dynamic load and stress were compared for several test conditions. These are very similar in shape, which means the analysis successfully simulates the physical behavior of the test gears. The predicted peak value of the dynamic load agrees with the measurement results within an average error of 4.9 percent except at low-torque, high-speed conditions. Predictions of peak dynamic root stress are generally within 10 to 15 percent of the measured values.

Geared-elevator flutter study. [transonic flutter characteristics of empennage

Science.gov (United States)

Ruhlin, C. L.; Doggett, R. V., Jr.; Gregory, R. A.

1976-01-01

The paper describes an experimental and analytical study of the transonic flutter characteristics of an empennage flutter model having an all-movable horizontal tail with a geared elevator. Two configurations were flutter tested: one with a geared elevator and one with a locked elevator with the model cantilever-mounted on a sting in the wind tunnel. The geared-elevator configuration fluttered experimentally at about 20% higher dynamic pressures than the locked-elevator configuration. The experimental flutter boundary was nearly flat at transonic speeds for both configurations. It was found that an analysis which treated the elevator as a discrete surface predicted flutter dynamic pressure levels better than analyses which treated the stabilizer and elevator as a warped surface. Warped-surface methods, however, predicted more closely the experimental flutter frequencies and Mach number trends.

Summary report : working group 5 on 'electron beam-driven plasma and structure based acceleration concepts'

International Nuclear Information System (INIS)

Conde, M. E.; Katsouleas, T.

2000-01-01

The talks presented and the work performed on electron beam-driven accelerators in plasmas and structures are summarized. Highlights of the working group include new experimental results from the E-157 Plasma Wakefield Experiment, the E-150 Plasma Lens Experiment and the Argonne Dielectric Structure Wakefield experiments. The presentations inspired discussion and analysis of three working topics: electron hose instability, ion channel lasers and the plasma afterburner

Fiber Optic Strain Sensor for Planetary Gear Diagnostics

Science.gov (United States)

Kiddy, Jason S.; Lewicki, David G.; LaBerge, Kelsen E.; Ehinger, Ryan T.; Fetty, Jason

2011-01-01

This paper presents a new sensing approach for helicopter damage detection in the planetary stage of a helicopter transmission based on a fiber optic strain sensor array. Complete helicopter transmission damage detection has proven itself a difficult task due to the complex geometry of the planetary reduction stage. The crowded and complex nature of the gearbox interior does not allow for attachment of sensors within the rotating frame. Hence, traditional vibration-based diagnostics are instead based on measurements from externally mounted sensors, typically accelerometers, fixed to the gearbox exterior. However, this type of sensor is susceptible to a number of external disturbances that can corrupt the data, leading to false positives or missed detection of potentially catastrophic faults. Fiber optic strain sensors represent an appealing alternative to the accelerometer. Their small size and multiplexibility allows for potentially greater sensing resolution and accuracy, as well as redundancy, when employed as an array of sensors. The work presented in this paper is focused on the detection of gear damage in the planetary stage of a helicopter transmission using a fiber optic strain sensor band. The sensor band includes an array of 13 strain sensors, and is mounted on the ring gear of a Bell Helicopter OH-58C transmission. Data collected from the sensor array is compared to accelerometer data, and the damage detection results are presented

Some calculation formulae for the candu 6 hypoid gearing. a physical point of view

International Nuclear Information System (INIS)

Doca, C.; Paunoiu, C.

2015-01-01

The CANDU 6 reactor.s Adjuster Unit consists of a tubular, stainless steel, neutron absorbing element which is raised and lowered within a guide tube. The Adjuster Unit is suspended from a cable which is wound around the sheave of a drive mechanism. To provide a very fine ''up-down'' displacement of the absorbing element, the adjuster drive mechanism incorporates a hypoid-gearing containing a conical spiroid pinion and a conical spiroid gear , having their axes at rights angle. Here represents the gear.s teeth number. By its conical spiroid pinion, its spiroid gear with double-involute teeth, and its reduction (transmission) ratio , this hypoid-gearing seems to be a special type mechanism, not encountered (by the authors, at least) in the classical engineering textbooks, where the most analyzed examples only are for and . Elaborated from a physical point of view, the paper demonstrates and proposes a number of calculation formulae for the main geometrical elements of a same CANDU 6 hypoid-gearing. Finally, the paper presents a very good (exact, practically) superposition between the values obtained using the proposed calculation formulae, and the known CANDU 6 hypoid-gearing.s geometrical values. Al these general calculation formulae are helpful for well understanding the dynamics and kinematics of the adjuster drive mechanism, and represent the minimum needed knowledge for some possible applications, in other mechanical systems, of the hypoid-gearing with a so large reduction rate . 11N1502NiN15012NNi51N10050i150i. (authors)

Investigation of the paired-gear method in selectivity studies

DEFF Research Database (Denmark)

Sistiaga, Manu; Herrmann, Bent; Larsen, R.B.

2009-01-01

was repeated throughout the eight cases in this investigation. When using the paired-gear method, the distribution of the estimated L50 and SR is wider; the distribution of the estimated split parameter has a higher variability than the true split; the estimated mean L50 and SR can be biased; the estimated...... recommend that the methodology used to obtain selectivity estimates using the paired-gear method be reviewed....

Thermal Behavior of Aerospace Spur Gears in Normal and Loss-of-Lubrication Conditions

Science.gov (United States)

Handschuh, Robert F.

2015-01-01

Testing of instrumented spur gears operating at aerospace rotorcraft conditions was conducted. The instrumented gears were operated in a normal and in a loss-of-lubrication environment. Thermocouples were utilized to measure the temperature at various locations on the test gears and a test utilized a full-field, high-speed infrared thermal imaging system. Data from thermocouples was recorded during all testing at 1 hertz. One test had the gears shrouded and a second test was run without the shrouds to permit the infrared thermal imaging system to take data during loss-of-lubrication operation. Both tests using instrumented spur gears were run in normal and loss-of-lubrication conditions. Also the result from four other loss-of-lubrication tests will be presented. In these tests two different torque levels were used while operating at the same rotational speed (10000 revolutions per minute).

‘Machinic Trajectories’: Appropriated Devices as Post-Digital Drawing Machines

Directory of Open Access Journals (Sweden)

Andres Wanner

2014-12-01

Full Text Available This article presents a series of works called Machinic Trajectories, consisting of domestic devices appropriated as mechanical drawing machines. These are contextualized within the post-digital discourse, which integrates messy analog conditions into the digital realm. The role of eliciting and examining glitches for investigating a technology is pointed out. Glitches are defined as short-lived, unpremeditated aesthetic results of a failure; they are mostly known as digital phenomena, but I argue that the concept is equally applicable to the output of mechanical machines. Three drawing machines will be presented: The Opener, The Mixer and The Ventilator. In analyzing their drawings, emergent patterns consisting of unpremeditated visual artifacts will be identified and connected to irregularities of the specific technologies. Several other artists who work with mechanical and robotic drawing machines are introduced, to situate the presented works and reflections in a larger context of practice and to investigate how glitch concepts are applicable to such mechanical systems. 

Power Consumption Optimization in Tooth Gears Processing

Science.gov (United States)

Kanatnikov, N.; Harlamov, G.; Kanatnikova, P.; Pashmentova, A.

2018-01-01

The paper reviews the issue of optimization of technological process of tooth gears production of the power consumption criteria. The authors dwell on the indices used for cutting process estimation by the consumed energy criteria and their applicability in the analysis of the toothed wheel production process. The inventors proposed a method for optimization of power consumptions based on the spatial modeling of cutting pattern. The article is aimed at solving the problem of effective source management in order to achieve economical and ecological effect during the mechanical processing of toothed gears. The research was supported by Russian Science Foundation (project No. 17-79-10316).

Identification of mine rescue equipment reduction gears technical condition

Science.gov (United States)

Gerike, B. L.; Klishin, V. I.; Kuzin, E. G.

2017-09-01

The article presents the reasons for adopting intelligent service of mine belt conveyer drives concerning evaluation of their technical condition based on the diagnostic techniques instead of regular preventative maintenance. The article reveals the diagnostic results of belt conveyer drive reduction gears condition taking into account the parameters of lubricating oil, vibration and temperature. Usage of a complex approach to evaluate technical conditions allows reliability of the forecast to be improved, which makes it possible not only to prevent accidental breakdowns and eliminate unscheduled downtime, but also to bring sufficient economic benefits through reduction of the term and scope of work during overhauls.

Wear of Spur Gears Having a Dithering Motion and Lubricated with a Perfluorinated Polyether Grease

Science.gov (United States)

Krantz, Timothy; Oswald, Fred; Handschuh, Robert

2007-01-01

Gear contact surface wear is one of the important failure modes for gear systems. Dedicated experiments are required to enable precise evaluations of gear wear for a particular application. The application of interest for this study required evaluation of wear of gears lubricated with a grade 2 perfluorinated polyether grease and having a dithering (rotation reversal) motion. Experiments were conducted using spur gears made from AISI 9310 steel. Wear was measured using a profilometer at test intervals encompassing 10,000 to 80,000 cycles of dithering motion. The test load level was 1.1 GPa maximum Hertz contact stress at the pitch-line. The trend of total wear as a function of test cycles was linear, and the wear depth rate was approximately 1.2 nm maximum wear depth per gear dithering cycle. The observed wear rate was about 600 times greater than the wear rate for the same gears operated at high speed and lubricated with oil.

Drawings of fossils by Robert Hooke and Richard Waller

Science.gov (United States)

Kusukawa, Sachiko

2013-01-01

The drawings of fossils by Robert Hooke and Richard Waller that were the basis of the engravings in Hooke's Posthumous works (1705) are published here for the first time. The drawings show that both Hooke and Waller were proficient draftsmen with a keen eye for the details of petrified objects. These drawings provided Hooke with a polemic edge in making the case for the organic origins of ‘figured stones’.

The tribological failure diagnosis of spur gear by an expert system

Science.gov (United States)

Su, Y. L.; Lin, J. S.; Hsieh, S. K.

1993-07-01

The failure of tribo-elements at an early stage, before the designed lifetime, is attributable to the complex interaction of many factors, which can be diagnosed by various techniques. These techniques can be learned in a certain period of time, while the knowledge of failure analysis must have accumulated from a long experience of practical work. For this reason, a computerized expert system program, developed from artificial intelligence (PC Plus, an inference engine shell), was constructed for spur gear tribological failure diagnosis. The knowledge was expressed as many 'if-then' rules and a 'frame' structure of inheritance. Note that the certainty factor of the rules is itself a special characteristic of this system and the 'man-machine' interface is very friendly, the graphical interpretation being an example. The system was finally validated by the twin roller wear test which can be recognized as the motion of a spur gear near the pitch-line region. The failure characteristics of the worn rollers were transferred to the expert system by means of a 'user-friendly' interface to deduce the reason for the failure.

Landing Gear Components Noise Study - PIV and Hot-Wire Measurements

Science.gov (United States)

Hutcheson, Florence V.; Burley, Casey L.; Stead, Daniel J.; Becker, Lawrence E.; Price, Jennifer L.

2010-01-01

PIV and hot-wire measurements of the wake flow from rods and bars are presented. The test models include rods of different diameters and cross sections and a rod juxtaposed to a plate. The latter is representative of the latch door that is attached to an aircraft landing gear when the gear is deployed, while the single and multiple rod configurations tested are representative of some of the various struts and cables configuration present on an aircraft landing gear. The test set up is described and the flow measurements are presented. The effect of model surface treatment and freestream turbulence on the spanwise coherence of the vortex shedding is studied for several rod and bar configurations.

Architectural Drawing

DEFF Research Database (Denmark)

Steinø, Nicolai

2018-01-01

In a time of computer aided design, computer graphics and parametric design tools, the art of architectural drawing is in a state of neglect. But design and drawing are inseparably linked in ways which often go unnoticed. Essentially, it is very difficult, if not impossible, to conceive of a design...... is that computers can represent graphic ideas both faster and better than most medium-skilled draftsmen, drawing in design is not only about representing final designs. In fact, several steps involving the capacity to draw lie before the representation of a final design. Not only is drawing skills an important...... prerequisite for learning about the nature of existing objects and spaces, and thus to build a vocabulary of design. It is also a prerequisite for both reflecting and communicating about design ideas. In this paper, a taxonomy of notation, reflection, communication and presentation drawing is presented...

Development of a stereoscopic three-dimensional drawing application

Science.gov (United States)

Carver, Donald E.; McAllister, David F.

1991-08-01

With recent advances in 3-D technology, computer users have the opportunity to work within a natural 3-D environment; a flat panel LCD computer display of this type, the DTI-100M made by Dimension Technologies, Inc., recently went on the market. In a joint venture between DTI and NCSU, an object-oriented 3-D drawing application, 3-D Draw, was developed to address some issues of human interface design for interactive stereo drawing applications. The focus of this paper is to determine some of the procedures a user would naturally expect to follow while working within a true 3-D environment. The paper discusses (1) the interface between the Macintosh II and DTI-100M during implementation of 3-D Draw, including stereo cursor development and presentation of current 2-D systems, with an additional `depth'' parameter, in the 3-D world, (2) problems in general for human interface into the 3-D environment, and (3) necessary functions and/or problems in developing future stereoscopic 3-D operating systems/tools.

Evaluation method of lead measurement accuracy of gears using a wedge artefact

International Nuclear Information System (INIS)

Komori, Masaharu; Takeoka, Fumi; Kubo, Aizoh; Okamoto, Kazuhiko; Osawa, Sonko; Sato, Osamu; Takatsuji, Toshiyuki

2009-01-01

The reduction of the vibration and noise of gears is an important issue in mechanical devices such as vehicles and wind turbines. The characteristics of the vibration and noise of gears are markedly affected by deviations of the tooth flank form of micrometre order; therefore, a strict quality control of the tooth flank form is required. The accuracy of the lead measurement for a gear-measuring instrument is usually evaluated using a master gear or a lead master. However, it is difficult to manufacture masters with high accuracy because the helix is a complicated geometrical form. In this paper, we propose a method of evaluating a gear-measuring instrument using a wedge artefact, which includes a highly precise plane surface. The concept of the wedge artefact is described and a mathematical model of the measuring condition of the wedge artefact is constructed. Theoretical measurement results for the wedge artefact are calculated. The wedge artefact is designed and produced on the basis of the theoretical measurement results. A measurement experiment using the wedge artefact is carried out and its effectiveness is verified

Integration of a silicon-based microprobe into a gear measuring instrument for accurate measurement of micro gears

International Nuclear Information System (INIS)

Ferreira, N; Krah, T; Jeong, D C; Kniel, K; Härtig, F; Metz, D; Dietzel, A; Büttgenbach, S

2014-01-01

The integration of silicon micro probing systems into conventional gear measuring instruments (GMIs) allows fully automated measurements of external involute micro spur gears of normal modules smaller than 1 mm. This system, based on a silicon microprobe, has been developed and manufactured at the Institute for Microtechnology of the Technische Universität Braunschweig. The microprobe consists of a silicon sensor element and a stylus which is oriented perpendicularly to the sensor. The sensor is fabricated by means of silicon bulk micromachining. Its small dimensions of 6.5 mm × 6.5 mm allow compact mounting in a cartridge to facilitate the integration into a GMI. In this way, tactile measurements of 3D microstructures can be realized. To enable three-dimensional measurements with marginal forces, four Wheatstone bridges are built with diffused piezoresistors on the membrane of the sensor. On the reverse of the membrane, the stylus is glued perpendicularly to the sensor on a boss to transmit the probing forces to the sensor element during measurements. Sphere diameters smaller than 300 µm and shaft lengths of 5 mm as well as measurement forces from 10 µN enable the measurements of 3D microstructures. Such micro probing systems can be integrated into universal coordinate measuring machines and also into GMIs to extend their field of application. Practical measurements were carried out at the Physikalisch-Technische Bundesanstalt by qualifying the microprobes on a calibrated reference sphere to determine their sensitivity and their physical dimensions in volume. Following that, profile and helix measurements were carried out on a gear measurement standard with a module of 1 mm. The comparison of the measurements shows good agreement between the measurement values and the calibrated values. This result is a promising basis for the realization of smaller probe diameters for the tactile measurement of micro gears with smaller modules. (paper)

76 FR 16610 - Proposed Information Collection; Comment Request; Pacific Islands Region Vessel and Gear...

Science.gov (United States)

2011-03-24

... Collection; Comment Request; Pacific Islands Region Vessel and Gear Identification Requirements AGENCY... and gear, as specified in 50 CFR 665 and 50 CFR 300. Vessels registered for use with a permit issued... require that certain fishing gear must be marked. In the pelagic longline fisheries, the vessel operator...

Feedforward Control of Gear Mesh Vibration Using Piezoelectric Actuators

Directory of Open Access Journals (Sweden)

Gerald T. Montague

1994-01-01

Full Text Available This article presents a novel means for suppressing gear mesh related vibrations. The key components in this approach are piezoelectric actuators and a high-frequency, analog feed forward controller. Test results are presented and show up to a 70% reduction in gear mesh acceleration and vibration control up to 4500 Hz. The principle of the approach is explained by an analysis of a harmonically excited, general linear vibratory system.

Development of the Upgraded DC Brush Gear Motor for Spacebus Platforms

Science.gov (United States)

Berning, Robert H.; Viout, Olivier

2010-01-01

The obsolescence of materials and processes used in the manufacture of traditional DC brush gear motors has necessitated the development of an upgraded DC brush gear motor (UBGM). The current traditional DC brush gear motor (BGM) design was evaluated using Six-Sigma process to identify potential design and production process improvements. The development effort resulted in a qualified UBGM design which improved manufacturability and reduced production costs. Using Six-Sigma processes and incorporating lessons learned during the development process also improved motor performance for UBGM making it a more viable option for future use as a deployment mechanism in space flight applications.

Reliability optimization design of the gear modification coefficient based on the meshing stiffness

Science.gov (United States)

Wang, Qianqian; Wang, Hui

2018-04-01

Since the time varying meshing stiffness of gear system is the key factor affecting gear vibration, it is important to design the meshing stiffness to reduce vibration. Based on the effect of gear modification coefficient on the meshing stiffness, considering the random parameters, reliability optimization design of the gear modification is researched. The dimension reduction and point estimation method is used to estimate the moment of the limit state function, and the reliability is obtained by the forth moment method. The cooperation of the dynamic amplitude results before and after optimization indicates that the research is useful for the reduction of vibration and noise and the improvement of the reliability.

50 CFR 654.22 - Gear restrictions.

Science.gov (United States)

2010-10-01

..., DEPARTMENT OF COMMERCE STONE CRAB FISHERY OF THE GULF OF MEXICO Management Measures § 654.22 Gear... retaining chamber. (6) A plastic or wire trap must have a degradable panel. (i) A plastic trap will be...

Bad Drawing

OpenAIRE

Burgoyne, Greig

2016-01-01

"Only when we move do we see the chains" - Rosa Luxemburg Bad drawing / paper cell is a site-specific drawing performance commissioned for The Prison Drawing Project, Scarborough jail, Yorkshire, presented as a film grafted onto the space that is the cell. It takes the notion of drawing as an act of covering and form of measurement, in an immersive act of attempted liberation. Measuring using rolls of paper, the film chronicles what could be seen as a bad day wallpapering a space, no ass...