Crack propagation and acoustic emission behavior of silver-added Dy123 bulk superconductor

International Nuclear Information System (INIS)

Yoneda, K.; Ye, J.

2006-01-01

The relationship between the crack propagation process and acoustic emission (AE) signals was investigated in 3-point bending tests in which stress loading was applied parallel to the c-axis of U-notched specimens cut from Dy123 bulk superconductors with and without the addition of silver (Ag). The average bending stress of the specimens containing 10 mass% of Ag was approximately 20% higher than that of the specimens without the addition of Ag; the total AE energy of the former specimens was approximately fourfold greater than that of the latter specimens. However, cracks initiated in all of the specimens at a bending stress level of around 25 MPa, regardless of the presence or absence of Ag. An analysis of the amplitude distribution revealed that the failure mode was matrix failure in both types of specimens. Cracks in the low-strength specimens without Ag propagated between gas holes or along cleavage planes, and the AE event count and total AE energy were low. By contrast, the high-strength Ag-added specimens had fewer gas holes and cleavage cracks on account of their improved microstructure. In these samples, crack propagation orthogonal to the cleavage planes caused Ag particles to separate from the matrix and induced cleavage cracks. The addition of Ag presumably had the effect of inhibiting crack propagation, with the result that the AE event count and AE energy increased. The results of this study indicate that failure phenomena can be interpreted by evaluating the amplitude distribution, AE event count and total AE energy. This suggests that the AE method is also applicable to evaluations of bulk superconductors

Electron paramagnetic resonance and AC susceptibility studies of Mn and Gd doped 1:2:3 superconductors

International Nuclear Information System (INIS)

La Robina, M.A.

1997-01-01

For many years superconductivity was considered to be a low temperature phenomenon occurring below ∼ 25K. All this changed in April 1986 when J. G. Bednorz and K. A. Muller showed that the oxide La 2-x Ba x CuO 4 becomes a superconductor at ∼ 30K. Later in December 1986 the oxides La 2-x Sr x CuO 4 and La 2-x Ba x CuO 4 synthesised under high pressure, were shown to superconduct at ∼ 40K and ∼ 50K, respectively. Finally in February 1987, Chu synthesised the classic superconductor YBa 2 Cu 3 O 6.8 , the so-called 1:2:3 material, which has a critical temperature circa 92K. In this thesis, electron paramagnetic resonance (EPR) and susceptibility measurements are reported on various superconductors. In 1987 Bowden et al., showed that pure phase 1:2:3 samples are characterised by an absence of Cu EPR signals. This contrasts sharply with the Green phase material, Y 2 Ba 1 Cu 1 O 5 , which shows a very large EPR signal with a g eff of 2.08. In an attempt to induce EPR signals, Mn doped 1:2:3 samples have been synthesised and characterised with EPR , AC susceptibility, XRD and SEM measurements. It is shown that Mn EPR signals are not evident in the Mn doped samples with a g eff of 2.09. Also, below T c the EPR signals of the lightly doped Mn samples vanish. It is argued that this is due to fluxoids motion within the superconductor, which gives rise to very large non-reproducible signals. It is suggested that the signals originate from Cu, impurity contaminants and multiple phases produced when the 1:2:3 superconductor is doped with Manganese (author)

Magnetic behavior of light rare earth ions in (Nd,Eu,Gd)-123 superconductors

Czech Academy of Sciences Publication Activity Database

Jirsa, Miloš; Rameš, Michal; Marcenat, C.; Wolf, T.

2013-01-01

Roč. 26, č. 4 (2013), s. 901-905 ISSN 1557-1939 R&D Projects: GA MŠk(CZ) ME10069 Institutional support: RVO:68378271 Keywords : high- T c superconductors * cuprates * thermodynamic properties * LRE-123 * paramagnetic ions Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.930, year: 2013

Trapped field recovery of bulk superconductor magnets by static field magnetization

Energy Technology Data Exchange (ETDEWEB)

Deng, Z., E-mail: zigang@kaiyodai.ac.jp [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan); Tsuzuki, K.; Miki, M.; Felder, B.; Hara, S.; Izumi, M. [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan)

2011-11-15

A series of initial trapped fields after ZFC or FC magnetization are used to simulate the attenuated trapped field. It is possible and easy to recover the lost trapped field and regain the best trapped field performance as before. In the re-magnetization process, the initial magnetic flux inside the bulk magnets will help to recover the trapped field. The optimum recovery field is recommended to be 2.5 times the saturation field of the bulk at LN2 temperature. Thanks to the trapped field of bulk high-temperature superconductors, they can be used as field-pole magnets in the high temperature superconducting (HTS) rotating machines. For example, an output power of 10 kW at 720 rpm was realized by an average trapped field of 0.56 T of eight melt-textured GdBa{sub 2}Cu{sub 3}O{sub y} (Gd-123) bulks at liquid nitrogen temperature in TUMSAT in 2004. Similarly to the HTS machines involving 1G or 2G wires, the trapped field of the bulk is possibly sensitive and even can be attenuated by the AC component field during the operation. Hence, it is necessary to recover the trapped field once being decreased to some extent in the practical application. From this point, we have investigated the trapped field recovery of HTS bulk magnets by static field magnetization in the paper. A series of different initial trapped fields after zero-field-cooling or field-cooling magnetization are used to simulate the attenuated trapped field. By comparing the trapped field peak and its distribution, the trapped field was found to be able to recover by the static field magnetization method with a stronger excitation field and the initial trapped flux inside the bulk also has an influence on the recovery process. The optimum recovery field was found to be about 2.5 times the saturated trapped field of the bulk at liquid nitrogen temperature, by which the bulk can regain the former best trapped field performance.

Technique of Critical Current Density Measurement of Bulk Superconductor with Linear Extrapolation Method

International Nuclear Information System (INIS)

Adi, Wisnu Ari; Sukirman, Engkir; Winatapura, Didin S.

2000-01-01

Technique of critical current density measurement (Jc) of HTc bulk ceramic superconductor has been performed by using linear extrapolation with four-point probes method. The measurement of critical current density HTc bulk ceramic superconductor usually causes damage in contact resistance. In order to decrease this damage factor, we introduce extrapolation method. The extrapolating data show that the critical current density Jc for YBCO (123) and BSCCO (2212) at 77 K are 10,85(6) Amp.cm - 2 and 14,46(6) Amp.cm - 2, respectively. This technique is easier, simpler, and the use of the current flow is low, so it will not damage the contact resistance of the sample. We expect that the method can give a better solution for bulk superconductor application. Key words. : superconductor, critical temperature, and critical current density

Superfluid phase stiffness in electron doped superconducting Gd-123

Science.gov (United States)

Das, P.; Ghosh, Ajay Kumar

2018-05-01

Current-voltage characteristics of Ce substituted Gd-123 superconductor exhibits nonlinearity below a certain temperature below the critical temperature. An exponent is extracted using the nonlinearity of current-voltage relation. Superfluid phase stiffness has been studied as a function of temperature following the Ambegaokar-Halperin-Nelson-Siggia (AHNS) theory. Phase stiffness of the superfluid below the superconducting transition is found to be sensitive to the change in the carrier concentration in superconducting system. There may be a crucial electron density which affects superfluid stiffness strongly. Electron doping is found to be effective even if the coupling of the superconducting planes is changed.

Pulsed Field Waveforms for Magnetization of HTS Gd-Ba-Cu-O Bulk Magnets

International Nuclear Information System (INIS)

Ida, T; Matsuzaki, H; Morita, E; Sakashita, H; Harada, T; Ogata, H; Kimura, Y; Miki, M; Kitano, M; Izumi, M

2006-01-01

Progress in pulse magnetization technique for high-temperature superconductor bulks of melt-textured RE-Ba-Cu-O with large diameter is important for the realization of power applications. We studied the pulsed power source and pulsed field waveforms to enhance to improve the magnetization properties for Gd-Ba-Cu-O bulk. The risetime and duration of pulse waveform effectively varied distribution of magnetic flux

Crystallographic and electrical properties of Pr substituted Gd-123 nanometre sized high temperature superconductors

International Nuclear Information System (INIS)

Huse, V.R.; Mote, V.D.; Shah, S.S.; Dole, B.N.; Purushotham, Y.; Dhar, S.K.

2011-01-01

The samples of Gd 1-x Pr x Ba 2 Cu 3 O 7-δ with compositions x = 0.0, 0.1 and 0.3 were prepared by ceramic route. The XRD study of all samples is carried out. The XRD studies of the samples prepared by ceramic route show GdPr-123 system have an orthorhombic perovskite structure. The lattice parameters, oxygen content, volume of unit cell, orthorhombic perovskite structure. The lattice parameters, oxygen content, volume of unit cell, orthorhombic distortion, hole concentration in CuO 2 plane and charge on Cu-O plane were evaluated using XRD data. It is found that the lattice parameters, volume of unit cell increase while oxygen content orthorhombic distortion, hole concentration (Psh) and average charge (p) decrease as doping percentage of Pr increases. The resistivity measurement shows the transition temperature decreases while transition width increases with increasing Pr concentration. The suppression of superconductivity may be due to reduction in hole concentration or magnetic pair breaking. We report such qualitative results of Pr substituted Gd-123 in this paper quantitatively. (author)

Comparison of simulation and experiment on levitation force between GdBCO bulk superconductor and superconducting magnet

Energy Technology Data Exchange (ETDEWEB)

Araki, S., E-mail: satoshi@sum.sd.keio.ac.j [Department of System Design Engineering, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan); Nagashima, K.; Seino, H. [Railway Technical Research Institute, 2-8-38 Hikari-cho, Kokubunji, Tokyo 185-8540 (Japan); Murakami, T.; Sawa, K. [Department of System Design Engineering, Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan)

2009-10-15

High temperature bulk superconductors have significant potential for various engineering applications such as a flywheel energy storage system. This system is expected to decrease the energy loss by using bulk superconductors for the bearing. Recently, the authors have developed a new superconducting magnet to realize large levitation force. In this system, the axial component of magnetic field is canceled each other but the radial component of magnetic field expects to be enhanced. Thus, it was expected that the large levitation force can be realized and its time relaxation will be decreased. And in the previous paper, the levitation force and its time relaxation were measured under the various conditions by using this new magnet. But it is difficult to consider what phenomenon has happened in the bulk from only experimental results. In addition the quantitative evaluation cannot be done only by the experimental results, for example, the influence of the magnetic field penetration and magnetic distribution around a bulk superconductor on the maximum force and so on. Thus, in this paper, the authors simulated the levitation force of bulk superconductor by using ELF/MAGIC, which is a three-dimensional electromagnetic analytical software. In the simulation the bulk was considered as a rigid body and the simulation was executed under the same conditions and model with the experiment. The distribution of magnetic field and the levitation force were obtained and discussed.

Comparison of simulation and experiment on levitation force between GdBCO bulk superconductor and superconducting magnet

International Nuclear Information System (INIS)

Araki, S.; Nagashima, K.; Seino, H.; Murakami, T.; Sawa, K.

2009-01-01

High temperature bulk superconductors have significant potential for various engineering applications such as a flywheel energy storage system. This system is expected to decrease the energy loss by using bulk superconductors for the bearing. Recently, the authors have developed a new superconducting magnet to realize large levitation force. In this system, the axial component of magnetic field is canceled each other but the radial component of magnetic field expects to be enhanced. Thus, it was expected that the large levitation force can be realized and its time relaxation will be decreased. And in the previous paper, the levitation force and its time relaxation were measured under the various conditions by using this new magnet. But it is difficult to consider what phenomenon has happened in the bulk from only experimental results. In addition the quantitative evaluation cannot be done only by the experimental results, for example, the influence of the magnetic field penetration and magnetic distribution around a bulk superconductor on the maximum force and so on. Thus, in this paper, the authors simulated the levitation force of bulk superconductor by using ELF/MAGIC, which is a three-dimensional electromagnetic analytical software. In the simulation the bulk was considered as a rigid body and the simulation was executed under the same conditions and model with the experiment. The distribution of magnetic field and the levitation force were obtained and discussed.

Large area bulk superconductors

Science.gov (United States)

Miller, Dean J.; Field, Michael B.

2002-01-01

A bulk superconductor having a thickness of not less than about 100 microns is carried by a polycrystalline textured substrate having misorientation angles at the surface thereof not greater than about 15.degree.; the bulk superconductor may have a thickness of not less than about 100 microns and a surface area of not less than about 50 cm.sup.2. The textured substrate may have a thickness not less than about 10 microns and misorientation angles at the surface thereof not greater than about 15.degree.. Also disclosed is a process of manufacturing the bulk superconductor and the polycrystalline biaxially textured substrate material.

Project of RE123 bulk superconductors fabrication in a microgravity environment; Bishojuryokuka chodensotai seizo purojekuto

Energy Technology Data Exchange (ETDEWEB)

Sakai, N; Murakami, M [International Superconductivity Technology Center, Tokyo (Japan); Shisa, A [Ishikawajima-Harima Heavy Industries Co., Ltd., Toky o(Japan); Hirata, H [Institute for Unmanned Space Experiment Free Flyer, Tokyo (Japan)

1999-11-25

Large single-grain bulk rare earth element (RE)-Ba-Cu-O superconductors can be used for various applications such magnetic bearings, load trapped field magnets. The magnetic field generated by bulk RE-Ba-Cu-O superconductors is proportional to its radius, however, the growth of a large single-grain bulk with good quality is difficult due to contamination from the substrate or the crucible and also due to liquid loss. Such problems can be solved by growing RE-Cu-O bulk in a microgravity environment, where the bulk can be supported by a seed crystal alone during crystal growth. Such experiments will be conducted in the Unmanned Space Experiment Recovery System (USERS) project. In this paper, the experiment plan and the present status of the system development are reported. (author)

Modelling of bulk superconductor magnetization

International Nuclear Information System (INIS)

Ainslie, M D; Fujishiro, H

2015-01-01

This paper presents a topical review of the current state of the art in modelling the magnetization of bulk superconductors, including both (RE)BCO (where RE = rare earth or Y) and MgB 2 materials. Such modelling is a powerful tool to understand the physical mechanisms of their magnetization, to assist in interpretation of experimental results, and to predict the performance of practical bulk superconductor-based devices, which is particularly important as many superconducting applications head towards the commercialization stage of their development in the coming years. In addition to the analytical and numerical techniques currently used by researchers for modelling such materials, the commonly used practical techniques to magnetize bulk superconductors are summarized with a particular focus on pulsed field magnetization (PFM), which is promising as a compact, mobile and relatively inexpensive magnetizing technique. A number of numerical models developed to analyse the issues related to PFM and optimise the technique are described in detail, including understanding the dynamics of the magnetic flux penetration and the influence of material inhomogeneities, thermal properties, pulse duration, magnitude and shape, and the shape of the magnetization coil(s). The effect of externally applied magnetic fields in different configurations on the attenuation of the trapped field is also discussed. A number of novel and hybrid bulk superconductor structures are described, including improved thermal conductivity structures and ferromagnet–superconductor structures, which have been designed to overcome some of the issues related to bulk superconductors and their magnetization and enhance the intrinsic properties of bulk superconductors acting as trapped field magnets. Finally, the use of hollow bulk cylinders/tubes for shielding is analysed. (topical review)

Pinning performance of (Nd,Eu,Gd)-123 superconductors: Comparison of melt-textured pellet and single crystal

Czech Academy of Sciences Publication Activity Database

Jirsa, Miloš; Rameš, Michal; Jurek, Karel; Muralidhar, M.; Das, P.; Koblischka, M.R.; Wolf, T.

2008-01-01

Roč. 151, č. 1 (2008), s. 25-30 ISSN 0921-5107 R&D Projects: GA ČR GA202/05/0173; GA MŠk 1P05ME728 Institutional research plan: CEZ:AV0Z10100520 Keywords : high-temperature superconductors * cuprous oxides * superconductivity perovskites, * (Nd,Eu,Gd)BaCuO * ternary compounds * melt-textured materials Subject RIV: BM - Solid Matter Physics ; Magnetism

Interior seeding for the fabrication of single-grain REBCO bulk superconductors

International Nuclear Information System (INIS)

Kim, C-J; Park, S-D; Jun, B-H; Park, H-W

2016-01-01

This study presents a new seeding technique, named ‘interior seeding’ which allows the growth of a single REBCO (RE: rare-earth elements) grain in the interior of REBCO compacts. The key techniques of interior seeding are to provide appropriate open space for seeds in the interior of REBCO powder compacts to supply air or oxygen to the seeds, and to minimize the contact area between the seeds and liquid. The advantages of interior seeding are as follows: (1) simultaneous growth from the seed to the top and bottom of the REBCO compacts is possible, (2) fractions of the a-b growth sector and the a-c growth sector on the top surface can be controlled and (3) the top surfaces of the single-grain REBCO bulk superconductors are free from samarium or neodymium contamination from the used seeds. The very large single-grain Y 1.5 Ba 2 Cu 3 O 7−y (Y1.5) bulk superconductors (42 mm) were successfully fabricated using a melt growth (MG) process combined with interior seeding. Also, large-grain Y1.5 bulk superconductors (41 mm) with 〈110〉/〈110〉 and 〈100〉/〈100〉 grain junctions were fabricated using multiple interior seeding. In this paper, the detailed process of interior seeding, the development of top surface patterns and the properties of single-grain Y123 bulk superconductors fabricated using interior seeding were reported. (paper)

Fast neutron induced flux pinning in Tl-based high-Tc single crystals and thin films, highly textured tapes and melt-textured bulk 123-superconductors

International Nuclear Information System (INIS)

Brandstaetter, G.; Samadi Hosseinalli, G.; Kern, C.; Sauerzopf, F.M.; Schulz, G.W.; Straif, W.; Yang, X.; Weber, H.W.; Hu, Q.Y.

1999-01-01

Various compounds (TI-2223, TI-1223, TI-2212) as well as material forms (single crystals, thin films, ceramics, tapes) of TI-based high temperature superconductors were investigated by magnetic and transport techniques. TI-2223 has a very 'low lying' irreversibility line (H parallel e) and negligible critical current densities J c at 77 K. However, the irreversibility line shifts to higher fields and temperatures and J c is strongly enhanced, even at 77 K, after fast neutron irradiation. In contrast, the related TI-1223 compound has a much steeper irreversibility line (H parallel c) similar to that of Y-123. J c is significant up to 77 K, even in the unirradiated state, and can be largely improved by neutron irradiation. Transport measurements made on TI-1223 tapes still show much lower critical current densities. TI-2212 and Tl-2223 thin films have J c 's at 77 K, which are comparable to those of TI-1223 single crystals. Transport measurements on highly textured Bi-2223 tapes as well as flux profile measurements on Nd-123 bulk superconductors confirm the beneficial effects of neutron induced defects (collision cascades) for flux pinning. (author)

High current density in bulk YBa2Cu3O/sub x/ superconductor

International Nuclear Information System (INIS)

Salama, K.; Selvamanickam, V.; Gao, L.; Sun, K.

1989-01-01

A liquid phase processing method for the fabrication of bulk YBa 2 Cu 3 O/sub x/ superconductors with large current carrying capacity has been developed. Slow cooling through the peritectic transformation (1030--980 degree C) has been shown to control the microstructure of these superconductors. A cooling rate of 1 degree C/h in this temperature range has yielded a microstructure with long plate type, thick grains oriented over a wide area. Current density up to 18 500 A/cm 2 has been obtained by continuous direct current measurements and in excess of 62 000 A/cm 2 with pulse current of 10 ms duration and 75 000 A/cm 2 using 1 ms pulse. The strong magnetic field dependence observed in sintered bulk 1-2-3 superconductors is also minimized to a large extent where a current density in excess of 37 000 A/cm 2 is obtained in a field of 6000 G

Single domain YBCO/Ag bulk superconductors fabricated by seeded infiltration and growth

International Nuclear Information System (INIS)

Iida, K; Babu, N H; Shi, Y; Cardwell, D A; Miyazaki, T; Murakami, M; Sakai, N

2008-01-01

We have applied the seeded infiltration and growth (IG) technique to the processing of samples containing Ag in an attempt to fabricate Ag-doped Y-Ba-Cu-O (YBCO) bulk superconductors with enhanced mechanical properties. The IG technique has been used successfully to grow bulk Ag-doped YBCO superconductors of up to 25 mm in diameter in the form of single grains. The distribution of Ag in the parent Y-123 matrix fabricated by the IG technique is observed to be at least as uniform as that in samples grown by conventional top seeded melt growth (TSMG). Fine Y-211 particles were observed to be embedded within the Y-123 matrix for the IG processed samples, leading to a high critical current density, J c , of over 70 kA/cm 2 at 77.3 K in self-field. The distribution of Y-211 in the IG sample microstructure, however, is inhomogeneous, which leads to a variation in the spatial distribution of J c throughout the bulk matrix. A maximum-trapped field of around 0.43 T at 1.2 mm above the sample surface (i.e. including 0.7 mm for the sensor mould thickness) is observed at liquid nitrogen temperature, despite the relatively small grain size of the sample (20 mm diameter x 7 mm thickness)

Melt-growth bulk superconductors and application to an axial-gap-type rotating machine

International Nuclear Information System (INIS)

Zhang, Yufeng; Zhou, Difan; Ida, Tetsuya; Miki, Motohiro; Izumi, Mitsuru

2016-01-01

The present manuscript addresses key issues in the course of our study of materials processing of bulk high-temperature superconductors, trapped flux and its application to a prototype axial-gap-type rotating machine. The TUMSAT group has conducted a series of studies since 2003 on the growth of GdBa 2 Cu 3 O 7−δ bulk material and its application in a compact low-speed high-torque rotating machine. In the stage of material growth, gaining the advantage of a large motive torque density requires large integrated flux in the motor/generators. A large grain surface might be required with sophisticated techniques for the melt-growth texture in the bulk with optimal flux pinning. In the second stage, the in situ magnetization procedure for bulk superconductors in the applied machine is a crucial part of the technology. Pulsed current excitation by using an armature copper winding has magnetized field pole bulks on the rotor. The axial-gap flux synchronous machine studied in the past decade is a condensed technology and indicates that further scientific development is required for a future compact machine to be superior to conventional ones in accordance with the cryogenic periphery and flux stabilization. (paper)

Force measurements for levitated bulk superconductors

International Nuclear Information System (INIS)

Tachi, Y.; Sawa, K.; Iwasa, Y.; Nagashima, K.; Otani, T.; Miyamoto, T.; Tomita, M.; Murakami, M.

2000-01-01

We have developed a force measurement system which enables us to directly measure the levitation force of levitated bulk superconductors. Experimental data of the levitation forces were compared with the results of numerical simulation based on the levitation model that we deduced in our previous paper. They were in fairly good agreement, which confirms that our levitation model can be applied to the force analyses for levitated bulk superconductors. (author)

Force measurements for levitated bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Tachi, Y. [Department of Electrical Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama (Japan); ISTEC, Superconductivity Research Laboratory, 1-16-25 Shibaura, Minato-ku, Tokyo (Japan). E-mail: tachi at istec.or.jp; Uemura, N. [Department of Electrical Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama (Japan); ISTEC, Superconductivity Research Laboratory, 1-16-25 Shibaura, Minato-ku, Tokyo (Japan); Sawa, K. [Department of Electrical Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama (Japan); Iwasa, Y. [Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology, Cambridge, MA (United States); Nagashima, K. [Railway Technical Research Institute, Hikari-cho, Kokubunji-shi, Tokyo (Japan); Otani, T.; Miyamoto, T.; Tomita, M.; Murakami, M. [ISTEC, Superconductivity Research Laboratory, 1-16-25 Shibaura, Minato-ku, Tokyo (Japan)

2000-06-01

We have developed a force measurement system which enables us to directly measure the levitation force of levitated bulk superconductors. Experimental data of the levitation forces were compared with the results of numerical simulation based on the levitation model that we deduced in our previous paper. They were in fairly good agreement, which confirms that our levitation model can be applied to the force analyses for levitated bulk superconductors. (author)

Mechanical properties of polycrystalline RuSr2GdCu2O8 superconductor

International Nuclear Information System (INIS)

Brum Leite Gusmao Pinheiro, Lincoln; Serbena, Francisco Carlos; Foerster, Carlos Eugenio; Rodrigues, Pedro Junior; Jurelo, Alcione Roberto; Chinelatto, Adilson Luiz; Junior, Jorge Luiz Pimentel

2011-01-01

Research highlights: → Hardness and elastic modulus of Ru-1212 phase measured by instrumented indentation are reported. → Polycrystalline samples were produced by a solid state reaction technique. → Samples were also characterized by SEM, XRD and electrical resistivity measurements. → Hardness and elastic modulus were 8.6 GPa and 145 GPa, respectively. → These values are comparable with those of Y-123. - Abstract: The main objective of this paper is to report the room temperature hardness and elastic modulus of the RuSr 2 GdCu 2 O 8 superconductor phase by instrumented indentation. Polycrystalline samples were produced by a solid state reaction technique. The samples were also characterized by scanning electron microscopy, X-ray diffraction and electrical resistivity measurements. The influence of porosity on the mechanical properties was avoided by considering only those indentations inside the grains. The hardness and elastic modulus were 8.6 GPa and 145 GPa, respectively. These values are comparable with those of Y-123. The indentation fracture toughness evaluated after conventional Vickers indentation was 1.9 MPa m 1/2 .

Development of a generic seed crystal for the fabrication of large grain (RE)-Ba-Cu-O bulk superconductors

International Nuclear Information System (INIS)

Shi, Y; Babu, N Hari; Cardwell, D A

2005-01-01

The critical current density, J c , irreversibility field, B irr , and magnetic field trapping ability of (LRE)-Ba-Cu-O bulk superconductors, where LRE is a light rare earth element such as Nd, Sm, Eu and Gd, are generally superior to those of the more common melt-processed Y-Ba-Cu-O (YBCO). The lack of availability of a suitable seed crystal to grow large, single grain (LRE)-Ba-Cu-O superconductors with controlled orientation, however, has hindered severely the development of these materials for engineering applications over the past ten years. In this communication we report for the first time the development of a generic seed crystal that can be used to fabricate any rare earth (RE) based (RE)-Ba-Cu-O ((RE)BCO) superconductor in the form of a large single grain with controlled orientation. The new seed crystal will potentially enable large grain (LRE)-Ba-Cu-O bulk superconductors to be fabricated routinely, as is the case for YBCO. This will enable the field trapping and current-carrying characteristics of these materials to be explored in more detail than has been possible to date. (rapid communication)

Mechanical properties of Nd-Ba-Cu-O bulk superconductors

International Nuclear Information System (INIS)

Matsui, Motohide; Sakai, Naomichi; Murakami, Masato; Osamura, Kozo

2003-01-01

We investigated the effects of Nd422 and Ag particles on the mechanical properties in Nd-Ba-Cu-O bulk superconductors. Both Nd422 and Ag particles were effective in decreasing the amount of microcracks running along the c direction. In the case of Nd422, however, excessive Nd422 addition enhanced the crack propagation, resulting in the degradation of mechanical strength. In the case of Ag addition, the beneficial effect of its ductile mechanical property was not observed. This was due to a relatively large size of Ag particles and low interfacial strength between Ag and Nd123 matrix. It was remarkable that the Weibull coefficient of the sample with Ag 2 O addition exceeded 13, which is reliable enough for practical engineering applications

Modelling and comparison of trapped fields in (RE)BCO bulk superconductors for activation using pulsed field magnetization

Science.gov (United States)

Ainslie, M. D.; Fujishiro, H.; Ujiie, T.; Zou, J.; Dennis, A. R.; Shi, Y.-H.; Cardwell, D. A.

2014-06-01

The ability to generate a permanent, stable magnetic field unsupported by an electromotive force is fundamental to a variety of engineering applications. Bulk high temperature superconducting (HTS) materials can trap magnetic fields of magnitude over ten times higher than the maximum field produced by conventional magnets, which is limited practically to rather less than 2 T. In this paper, two large c-axis oriented, single-grain YBCO and GdBCO bulk superconductors are magnetized by the pulsed field magnetization (PFM) technique at temperatures of 40 and 65 K and the characteristics of the resulting trapped field profile are investigated with a view of magnetizing such samples as trapped field magnets (TFMs) in situ inside a trapped flux-type superconducting electric machine. A comparison is made between the temperatures at which the pulsed magnetic field is applied and the results have strong implications for the optimum operating temperature for TFMs in trapped flux-type superconducting electric machines. The effects of inhomogeneities, which occur during the growth process of single-grain bulk superconductors, on the trapped field and maximum temperature rise in the sample are modelled numerically using a 3D finite-element model based on the H-formulation and implemented in Comsol Multiphysics 4.3a. The results agree qualitatively with the observed experimental results, in that inhomogeneities act to distort the trapped field profile and reduce the magnitude of the trapped field due to localized heating within the sample and preferential movement and pinning of flux lines around the growth section regions (GSRs) and growth sector boundaries (GSBs), respectively. The modelling framework will allow further investigation of various inhomogeneities that arise during the processing of (RE)BCO bulk superconductors, including inhomogeneous Jc distributions and the presence of current-limiting grain boundaries and cracks, and it can be used to assist optimization of

Improvement of the field-trapping capabilities of bulk Nd Ba Cu O superconductors using Ba Cu O substrates

Science.gov (United States)

Matsui, Motohide; Nariki, Shinya; Sakai, Naomichi; Iwafuchi, Kengo; Murakami, Masato

2006-07-01

We used Ba-Cu-O substrates to fabricate bulk Nd-Ba-Cu-O superconductors using a top-seeded melt-growth method. There were several advantages for the use of Ba-Cu-O substrate compared to conventional substrate materials such as MgO, ZrO2, Al2O3, RE123 and RE211 (RE = rare earth). The Ba-Cu-O did not react with the precursor and minimized liquid loss. Accordingly, the introduction of large-sized cracks was suppressed. We also found that Tc values were high at the bottom regions, which was ascribed to the beneficial effect of Ba-Cu-O in suppressing Nd/Ba substitution. As a result, we obtained bulk Nd-Ba-Cu-O superconductors that exhibited fairly good field-trapping capabilities, even at the bottom surfaces.

Long Gd-123 coated conductor by PLD method

International Nuclear Information System (INIS)

Fuji, H.; Igarashi, M.; Hanada, Y.; Miura, T.; Hanyu, S.; Kakimoto, K.; Iijima, Y.; Saitoh, T.

2008-01-01

We have developed long Gd-123 coated conductors by ion-beam-assisted deposition (IBAD) and pulsed-laser-deposition (PLD) method. Recently, large-scale reel-to-reel apparatus with the 110 cm x 15 cm assisting ion source was introduced to IBAD system. It was enable to produce 500 m-class IBAD-Gd 2 Zr 2 O 7 (GZO) tapes with Δφ of below 15 deg. and high throughputs of 3 m/h. Furthermore, apparatus with multi-lane and laser scanning was introduced to PLD system. As a result, end to end I c of 318 A were obtained for a 201.5 m long tape, and I c x L values were 64,077 Am. Furthermore, 500 m-class deposition was carried out by improving PLD conditions. As a result, I c x L values of 112,166 Am was obtained and it's a world record on August 2007. In the short samples, I c of over 500 A was obtained with Gd-123 thickness of 2.0 μm and over 100 A was obtained in magnetic field of 3 T, perpendicular to c-axis

Growth and structural characterization of single crystals of the magnetic superconductor Ru1-xSr2-yGd1+yCu2+xO8-δ (RuGd-1212) obtained by the partial melting technique

Science.gov (United States)

Yamaki, K.; Bamba, Y.; Mochiku, T.; Funahashi, S.; Matsushita, Y.; Irie, A.

2018-05-01

In this study, cubic single crystals of the magnetic superconductor Ru1-xSr2-yGd1+yCu2+xO8-δ (RuGd-1212) with typical dimensions of 100-150 μm in length were grown by the partial melting technique. Multiple 00l reflections were first observed by XRD measurements of the bulk RuGd-1212 single crystals. The resistivity of the obtained crystals was roughly estimated to be ∼24-80 mΩ cm and no superconducting transition was observed down to 4.2 K. From the XRD measurements and refinement of the crystal structure, it was apparent that the Ru and Sr sites of the single-crystal RuGd-1212 were partially substituted by Cu and Gd, respectively. Oxygen defects were found to be minor (δ ≈ 0.1). The lattice parameters a and c of the single crystals were found to be larger and smaller, respectively, than those of a polycrystalline sample.

Trapped magnetic field of a mini-bulk magnet using YBaCuO at 77 K

Science.gov (United States)

Fujimoto, Hiroyuki; Kamijo, Hiroki

2001-09-01

Melt-processed rare earth (RE)123 superconductors have a high Jc at 77 K and high magnetic field. Solidification processes for producing (L)RE123 superconductors and pinning centers in the (L)RE123 matrix are effective for obtaining high Jc, leading to high-field application as a superconducting quasi-permanent bulk magnet with the liquid nitrogen refrigeration. One of the promising applications is a superconducting magnet for the magnetically levitated train. We fabricated a mini-superconducting bulk magnet of 200×100 mm2, consisting of 18 bulks, which are a square 33 mm on a side and 10 mm in thickness, and magnetized the mini-magnet by field cooling. The mini-magnet showed the trapped magnetic field of larger than 0.1 T on the surface of the outer vessel of the magnet. The present preliminary study discusses trapped magnetic field properties of the mini-bulk magnet using YBaCuO superconductors at 77 K.

Numerical analysis of thermally actuated magnets for magnetization of superconductors

Energy Technology Data Exchange (ETDEWEB)

Li Quan; Yan Yu; Rawlings, Colin; Coombs, Tim, E-mail: ql229@cam.ac.u [EPEC Superconductivity Group, Engineering Department, University of Cambridge, Trumpington Street. Cambridge, CB2 1PZ (United Kingdom)

2010-06-01

Superconductors, such as YBCO bulks, have extremely high potential magnetic flux densities, comparing to rare earth magnets. Therefore, the magnetization of superconductors has attracted broad attention and contribution from both academic research and industry. In this paper, a novel technique is proposed to magnetize superconductors. Unusually, instead of using high magnetic fields and pulses, repeatedly magnetic waves with strength of as low as rare earth magnets are applied. These magnetic waves, generated by thermally controlling a Gadolinium (Gd) bulk with a rare earth magnet underneath, travel over the flat surface of a YBCO bulk and get trapped little by little. Thus, a very small magnetic field can be used to build up a very large magnetic field. In this paper, the modelling results of thermally actuated magnetic waves are presented showing how to transfer sequentially applied thermal pulses into magnetic waves. The experiment results of the magnetization of YBCO bulk are also presented to demonstrate how superconductors are progressively magnetized by small magnetic field

Numerical analysis of thermally actuated magnets for magnetization of superconductors

International Nuclear Information System (INIS)

Li Quan; Yan Yu; Rawlings, Colin; Coombs, Tim

2010-01-01

Superconductors, such as YBCO bulks, have extremely high potential magnetic flux densities, comparing to rare earth magnets. Therefore, the magnetization of superconductors has attracted broad attention and contribution from both academic research and industry. In this paper, a novel technique is proposed to magnetize superconductors. Unusually, instead of using high magnetic fields and pulses, repeatedly magnetic waves with strength of as low as rare earth magnets are applied. These magnetic waves, generated by thermally controlling a Gadolinium (Gd) bulk with a rare earth magnet underneath, travel over the flat surface of a YBCO bulk and get trapped little by little. Thus, a very small magnetic field can be used to build up a very large magnetic field. In this paper, the modelling results of thermally actuated magnetic waves are presented showing how to transfer sequentially applied thermal pulses into magnetic waves. The experiment results of the magnetization of YBCO bulk are also presented to demonstrate how superconductors are progressively magnetized by small magnetic field

Magnetic Signals of High-Temperature Superconductor Bulk During the Levitation Force Measurement Process

Science.gov (United States)

Huang, Huan; Zheng, Jun; Qian, Nan; Che, Tong; Zheng, Botian; Jin, Liwei; Deng, Zigang

2017-05-01

In order to study the commonly neglected magnetic field information in the course of levitation force measurement process in a superconducting maglev system, a multipoint magnetic field measurement platform was employed to acquire magnetic signals of a bulk high-Tc superconductor on both the top and the bottom surface. Working conditions including field cooling (FC) and zero field cooling were investigated for these vertical down and up motions above a permanent magnet guideway performed on a HTS maglev measurement system. We have discussed the magnetic flux variation process based on the Bean model. A magnetic hysteresis effect similar to the levitation force hysteresis loop of the bulk superconductor was displayed and analyzed in this paper. What is more valuable, there exists some available magnetic flux on the top surface of the bulk superconductor, and the proportion is as high as 62.42% in the FC condition, which provides an experimental hint to design the superconductor bulk and the applied field for practical use in a more efficient way. In particular, this work reveals real-time magnetic flux variation of the bulk superconductor in the levitation application, which is the other important information in contrast to the macroscopic levitation and guidance force investigations in previous studies, and it enriches the existing research methods. The results are significant for understanding the magnetic characteristic of superconductors, and they can contribute to optimize the present HTS maglev system design.

High temperature superconductor bulk materials. Fundamentals - processing - properties control - application aspects

International Nuclear Information System (INIS)

Krabbes, G.; Fuchs, G.; Canders, W.R.; May, H.; Palka, R.

2006-01-01

This book presents all the features of bulk high temperature superconducting materials. Starting from physical and chemical fundamentals, the authors move on to portray methods and problems of materials processing, thoroughly working out the characteristic properties of bulk superconductors in contrast to long conductors and films. The authors provide a wide range of specific materials characteristics with respect to the latest developments and future applications guiding from fundamentals to practical engineering examples. This book contains the following chapters: 1. Fundamentals 2. Growth and melt processing of YBCO 3. Pinning-relevant defects in bulk YBCO 4. Properties of bulk YBCO 5. Trapped fields 6. Improved YBCO based bulk superconductors and functional elements 7. Alternative systems 8. Peak effect 9. Very high trapped fields in YBCO permanent magnets 10. Engineering aspects: Field distribution in bulk HTSC 11. Inherently stable superconducting magnetic bearings 12. Application of bulk HTSCs in electromagnetic energy converters 13. Applications in magnet technologies and power supplies

Processing of bulk Bi-2223 high-temperature superconductor

Directory of Open Access Journals (Sweden)

Alexander Polasek

2005-12-01

Full Text Available The Bi2Sr2Ca2Cu3 O10+x (Bi-2223 is one of the main high temperature superconductors for applications. One of these applications is the Superconductor Fault Current Limiter (SCFCL, which is a very promising high temperature superconducting device. SCFCL's can be improved by using bulk superconductors with high critical currents, which requires a sufficiently dense and textured material. In the present work, a process for improving the microstructure of Bi-2223 bulk samples is investigated. Pressed precursor blocks are processed by sintering with a further partial melting step, in order to enhance the Bi-2223 grain texture and to healing cracks induced by pressing. In order to improve the microstructure, the precursor is mixed with silver powder before pressing. Samples with and without silver powder have been studied, with the aim of investigating the influence of silver on the microstructure evolution. The phase contents and the microstructure obtained have been analyzed through XRD and SEM/EDS. The electromagnetic characterization has been performed by Magnetic Susceptibility Analysis. We present and discuss the process and the properties of the superconducting blocks. High fractions of textured Bi-2223 grains have been obtained.

The influence of slow cooling on Y211 size and content in single-grain YBCO bulk superconductor through the infiltration-growth process

Energy Technology Data Exchange (ETDEWEB)

Ouerghi, A [Systems and Applied Mechanics Laboratory LASMAP, Polytechnic School of Tunisia, Rue El Kawarezmi La Marsa 743, Université de Carthage Tunis (Tunisia); Moutalbi, N., E-mail: nahed.moutalbi@yahoo.fr [Systems and Applied Mechanics Laboratory LASMAP, Polytechnic School of Tunisia, Rue El Kawarezmi La Marsa 743, Université de Carthage Tunis (Tunisia); Noudem, J.G. [CRISMAT-ENSICAEN (UMR-CNRS 6508), Université de Caen-Basse-Normandie, F-14050 Caen (France); LUSAC, Université de Caen-Basse-Normandie F-50130 Cherbourg-Octeville (France); M' chirgui, A. [Systems and Applied Mechanics Laboratory LASMAP, Polytechnic School of Tunisia, Rue El Kawarezmi La Marsa 743, Université de Carthage Tunis (Tunisia)

2017-03-15

Highlights: • YBCO bulk superconductors are produced by optimized Seeded Infiltration and Growth process. • The slow cooling time, in a fixed slow cooling temperature window, affects considerably the surface morphology and the bulk’s microstructure. • The Y211 particle’s size and content depend on the slow cooling time and its distribution behavior changes from one position to another. • There is an optimum slow cooling time, estimated to 88h, over which the shrinkage for both the liquid phase and the Y211 pellet is maximal, without any improvement of the crystal grain growth. • The magnetic trapped flux distribution for a given sample brings out the single grain characteristic. - Abstract: Highly textured YBa{sub 2}Cu{sub 3}O{sub 7-δ} (Y123) superconductors were produced using modified Textured Top Seeded Infiltration Growth (TSIG) process. The liquid source is made of only Y123 powder whereas the solid source is composed of Y{sub 2}BaCuO{sub 5} (Y211) powder. We aim to control the amount of liquid that infiltrates the solid pellet, which in turn controls the final amount of Y{sub 2}BaCuO{sub 5} particles in Y123 matrix. The effect of the slow cooling kinetics on sample morphology, on grain growth and on final microstructure was too investigated. It is shown that appropriate slow cooling time may also contribute to the control of the amount of Y211 inclusions in the final structure of Y123 bulk. We report herein the Y211 particle size and density distribution in the whole Y123 matrix. The present work proves that finest Y211 particles locate under the seed and that their size and density increase with distance from the seed.

Proposal of Magnetic Circuit using Magnetic Shielding with Bulk-Type High Tc Superconductors

Science.gov (United States)

Fukuoka, Katsuhiro; Hashimoto, Mitsuo; Tomita, Masaru; Murakami, Masato

Recently, bulk-type high Tc superconductors having a characteristic of critical current density over 104 A/cm2 in liquid nitrogen temperature (77K) on 1T, can be produced. They are promising for many practical applications such as a magnetic bearing, a magnetic levitation, a flywheel, a magnetic shielding and others. In this research, we propose a magnetic circuit that is able to use for the magnetic shield of plural superconductors as an application of bulk-type high Tc superconductors. It is a closed magnetic circuit by means of a toroidal core. Characteristics of the magnetic circuit surrounded with superconductors are evaluated and the possibility is examined. As the magnetic circuit of the ferrite core is surrounded with superconductors, the magnetic flux is shielded even if it leaked from the ferrite core.

Pinning characteristics in chemically modified (Nd, Eu, Gd)-Ba-Cu-O superconductors

Czech Academy of Sciences Publication Activity Database

Muralidhar, M.; Sakai, N.; Nishiyama, M.; Jirsa, Miloš; Machi, T.; Murakami, M.

2003-01-01

Roč. 82, č. 6 (2003), s. 943-945 ISSN 0003-6951 R&D Projects: GA AV ČR IAA1010919 Institutional research plan: CEZ:AV0Z1010914 Keywords : melt-textured superconductors * pinning defects * irreversibility field * bulk superconductors * ternary systems * twin structure Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 4.049, year: 2003

Gd-123 bulk field pole magnets cooled with condensed neon for axial-gap type synchronous motor

International Nuclear Information System (INIS)

Sano, T.; Kimura, Y.; Sugyo, D.; Yamaguchi, K.; Izumi, M.; Ida, T.; Sugimoto, H.; Miki, M.

2008-01-01

We have conducted to develop an axial-gap type synchronous propulsion motor with Gd-bulk HTS field pole magnets. It has been established on the fundamental technology upon the liquid nitrogen cooling. In the present study, we aimed an output improvement of the motor by the magnetic flux density enhancement of the bulk HTS, in a word, the trapped magnetic flux density on the HTS bulk. The output of the motor depends on the physics of the motor, the magnetic flux density, and the electric current density flowing through the armature. We have employed a condensed neon with a helium GM refrigerator. The bulk HTS placed on the rotor disk inside the motor frame was successfully cooled down with circulating condensed neon. The temperature at the bulk HTS surface reached 38 K. Upon magnetization, we developed controlled magnetic field density distribution coil (CMDC) composed of a couple of pulsed copper armature coil. In the magnetization procedure, with decreasing magnetization temperature, minute by minute, after Sander and Kamijyo that the step cooling magnetization method was used. In addition, the CMDC coil has enabled to control the applied flux distribution. Three parameters as the temperature, the applied magnetic field, and the effective applied flux density distribution were changed within eight times pulsed magnetizations in total. Up to 4th pulsed magnetization, we kept (1st step) high temperature, and subsequent pulsed magnetizations were done at low temperature. As a result, the highest maximum trapped magnetic flux density was reached 1.31 T, about 2.5 times compared to the value obtained upon cooling with liquid nitrogen. Consequently, the output of the motor has been enhanced to 25 kW from 10 kW taken in the previous operation

Improvement of the mechanical properties of bulk superconductors; Jushiganshin niyoru baruku chodendotai no kikaitekitokusei no kaizen

Energy Technology Data Exchange (ETDEWEB)

Tomita, M; Murakami, M [Superconductivity Research Laboratory, Tokyo (Japan)

1999-11-25

Large single-grain bulk rare earth element (RE)-Ba-Cu-O superconductors can trip large fields exceeding several teslas and thus can function as very strong quasi-permanent magnets. However, the maximum trapped field is essentially limited by the mechanical strength of the bulk superconductors. The stress produced by refrigeration sometimes causes cracking. A large electromagnetic force also acts on superconductors when they trap large magnetic fields, and this occasionally leads to device failure. We have recently found that epoxy resin can penetrate into bulk superconductors under certain conditions. Microstructural observation revealed that microcracks as well as porosities can be impregnated with epoxy resin, which greatly improves the mechanical properties of bulk RE-Ba-Cu-O and thus results in the improvement of field trapping capability. (author)

Surface barrier and bulk pinning in MgB$_2$ superconductor

OpenAIRE

Pissas, M.; Moraitakis, E.; Stamopoulos, D.; Papavassiliou, G.; Psycharis, V.; Koutandos, S.

2001-01-01

We present a modified method of preparation of the new superconductor MgB$_2$. The polycrystalline samples were characterized using x-ray and magnetic measurements. The surface barriers control the isothermal magnetization loops in powder samples. In bulk as prepared samples we always observed symmetric magnetization loops indicative of the presence of a bulk pinning mechanism. Magnetic relaxation measurements in the bulk sample reveal a crossover of surface barrier to bulk pinning.

Application of textured YBCO bulks with artificial holes for superconducting magnetic bearing

International Nuclear Information System (INIS)

Dias, D H N; Sotelo, G G; Moysés, L A; Telles, L G T; Bernstein, P; Aburas, M; Noudem, J G; Kenfaui, D; Chaud, X

2015-01-01

The levitation force between a superconductor and a permanent magnet has been investigated for the development of superconducting magnetic bearings (SMBs). Depending on the proposed application, the SMBs can be arranged with two kinds of symmetries: rotational or linear. The SMBs present passive operation, low level of noise and no friction, but they need a cooling system for their operation. Nowadays the cooling problem may be easily solved by the use of a commercial cryocooler. The levitation force of SMBs is directly related to the quality of the superconductor material (which depends on its critical current density) and the permanent magnet arrangement. Also, research about the YBa 2 Cu 3 O x (Y123) bulk materials has shown that artificial holes enhance the superconducting properties, in particular the magnetic trapped field. In this context, this work proposes the investigation of the levitation force of a bulk Y123 sample with multiple holes and the comparison of its performances with those of conventional plain Y123 superconductors. (paper)

Surface flux density distribution characteristics of bulk high-Tc superconductor in external magnetic field

International Nuclear Information System (INIS)

Torii, S.; Yuasa, K.

2004-01-01

Various magnetic levitation systems using oxide superconductors are developed as strong pinning forces are obtained in melt-processed bulk. However, the trapped flux of superconductor is moved by flux creep and fluctuating magnetic field. Therefore, to examine the internal condition of superconductor, the authors measure the dynamic surface flux density distribution of YBCO bulk. Flux density measurement system has a structure with the air-core coil and the Hall sensors. Ten Hall sensors are arranged in series. The YBCO bulk, which has 25 mm diameter and 13 mm thickness, is field cooled by liquid nitrogen. After that, magnetic field is changed by the air-core coil. This paper describes about the measured results of flux density distribution of YBCO bulk in the various frequencies of air-core coils currents

Surface flux density distribution characteristics of bulk high- Tc superconductor in external magnetic field

Science.gov (United States)

Torii, S.; Yuasa, K.

2004-10-01

Various magnetic levitation systems using oxide superconductors are developed as strong pinning forces are obtained in melt-processed bulk. However, the trapped flux of superconductor is moved by flux creep and fluctuating magnetic field. Therefore, to examine the internal condition of superconductor, the authors measure the dynamic surface flux density distribution of YBCO bulk. Flux density measurement system has a structure with the air-core coil and the Hall sensors. Ten Hall sensors are arranged in series. The YBCO bulk, which has 25 mm diameter and 13 mm thickness, is field cooled by liquid nitrogen. After that, magnetic field is changed by the air-core coil. This paper describes about the measured results of flux density distribution of YBCO bulk in the various frequencies of air-core coils currents.

Permanent magnet with MgB{sub 2} bulk superconductor

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, Akiyasu, E-mail: yamamoto@appchem.t.u-tokyo.ac.jp [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); JST-PRESTO, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Ishihara, Atsushi; Tomita, Masaru [Railway Technical Research Institute, 2-8-38 Hikari, Kokubunji, Tokyo 185-8540 (Japan); Kishio, Kohji [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan)

2014-07-21

Superconductors with persistent zero-resistance currents serve as permanent magnets for high-field applications requiring a strong and stable magnetic field, such as magnetic resonance imaging. The recent global helium shortage has quickened research into high-temperature superconductors (HTSs)—materials that can be used without conventional liquid-helium cooling to 4.2 K. Herein, we demonstrate that 40-K-class metallic HTS magnesium diboride (MgB{sub 2}) makes an excellent permanent bulk magnet, maintaining 3 T at 20 K for 1 week with an extremely high stability (<0.1 ppm/h). The magnetic field trapped in this magnet is uniformly distributed, as for single-crystalline neodymium-iron-boron. Magnetic hysteresis loop of the MgB{sub 2} permanent bulk magnet was determined. Because MgB{sub 2} is a simple-binary-line compound that does not contain rare-earth metals, polycrystalline bulk material can be industrially fabricated at low cost and with high yield to serve as strong magnets that are compatible with conventional compact cryocoolers, making MgB{sub 2} bulks promising for the next generation of Tesla-class permanent-magnet applications.

Bulk Superconductors in Mobile Application

Science.gov (United States)

Werfel, F. N.; Delor, U. Floegel-; Rothfeld, R.; Riedel, T.; Wippich, D.; Goebel, B.; Schirrmeister, P.

We investigate and review concepts of multi - seeded REBCO bulk superconductors in mobile application. ATZ's compact HTS bulk magnets can trap routinely 1 T@77 K. Except of magnetization, flux creep and hysteresis, industrial - like properties as compactness, power density, and robustness are of major device interest if mobility and light-weight construction is in focus. For mobile application in levitated trains or demonstrator magnets we examine the performance of on-board cryogenics either by LN2 or cryo-cooler application. The mechanical, electric and thermodynamical requirements of compact vacuum cryostats for Maglev train operation were studied systematically. More than 30 units are manufactured and tested. The attractive load to weight ratio is more than 10 and favours group module device constructions up to 5 t load on permanent magnet (PM) track. A transportable and compact YBCO bulk magnet cooled with in-situ 4 Watt Stirling cryo-cooler for 50 - 80 K operation is investigated. Low cooling power and effective HTS cold mass drives the system construction to a minimum - thermal loss and light-weight design.

Applied Hts Bulks and Wires to Rotating Machines for Marine Propulsion

Science.gov (United States)

Miki, M.; Felder, B.; Kimura, Y.; Tsuzuki, K.; Taguchi, R.; Shiliang, Y.; Xu, Y.; Ida, T.; Izumi, M.

2010-04-01

High-temperature superconductors allow a compact and efficient way to provide high-torque density to rotating machines with excellent operation. A field pole, providing flux density of more than 1.5 T around the armature, was initially designed for an axial-gap type with the flux parallel to the rotor axis. Melt-growth Gd-123 bulks as well as Bi-2223 wire windings have been successfully assembled on the rotor disk. No iron core was used, though being an auxiliary flux control found in most HTS motors. Both bulk and wire types have realized a practical motor operation within a limited output range. For bulks, a 15 kW, 720 rpm, synchronous motor was designed and tested in the group of TUMSAT, Kitano Seiki and University of Fukui. A bulk field pole was cooled down by liquid nitrogen and was magnetized in the motor. To enhance the output power to more than 30 kW, we developed a thermosyphon system using condensed neon. Another field pole with HTS wire for large-scale marine propulsion is also discussed on a 100 kW, 230 rpm tested machine. A closed-cycle condensed neon associated with thermal insulation is also reported.

Preparation of Superconductor YBCO-123/Ag Composite Through Urea Molten Salt

International Nuclear Information System (INIS)

Yustinus, P.; Indra-Gunawan; Wuryanto

1996-01-01

Superconductor YBCO-123/Ag composite has been prepared through Urea molten salt by mixing salt nitrate of Yttrium, Barium, Copper and Silver. The weight of Silver content varied from 0 % - 50 %. After pyrolysis process the powder was subjected to calcination at 300, 500 and 700 o C subsequently for 1 hour. The calcined powders was pelletized into a disk of 1.0 cm in diameter and thickness of 2-3 mm. Sintering of pellet samples was done at 900 o C for 16 hours. Meissner effect on all samples displayed superconductivity phenomena. Samples were examined by XRD, SEM, measurement of critical temperature by using susceptibility magnet vs temperature, and critical current density measurement by using four point probe. Based on orthorhombic structure of YBCO-123 the result of the lattice crystal calculation were is a = 3.8167 - 3.8241 A o ; b = 3.8561 - 3.8895 A o and c = 11.6518 - 11.7104 A o , this showed that silver did not influence the structure of YBCO. Superconductor YBCO-123/Ag composite was prepared. This was proved by critical current density. Jc data which showed increased with increasing of silver content and the highest result was 9.71 x 10 5 Amp/m 2

Surface flux density distribution characteristics of bulk high-T c superconductor in external magnetic field

International Nuclear Information System (INIS)

Nishikawa, H.; Torii, S.; Yuasa, K.

2005-01-01

This paper describes the measured results of the two-dimensional flux density distribution of a YBCO bulk under applied AC magnetic fields with various frequency. Melt-processed oxide superconductors have been developed in order to obtain strong pinning forces. Various electric mechanical systems or magnetic levitation systems use those superconductors. The major problem is that cracks occur because the bulk superconductors are brittle. The bulk may break in magnetizing process after cracks make superconducting state instable. The trapped flux density and the permanent current characteristics of bulk superconductors have been analyzed, so as to examine the magnetizing processes or superconducting states of the bulk. In those studies, the two-dimensional surface flux density distributions of the bulk in static fields are discussed. On the other hand, the distributions in dynamic fields are little discussed. We attempted to examine the states of the bulk in the dynamic fields, and made a unique experimental device which has movable sensors synchronized with AC applied fields. As a result, the two-dimensional distributions in the dynamic fields are acquired by recombining the one-dimensional distributions. The dynamic states of the flux of the bulk and the influences of directions of cracks are observed from the distributions. In addition, a new method for measuring two-dimensional flux density distribution under dynamic magnetic fields is suggested

Atomic hydrogen effects on high-Tc superconductors

International Nuclear Information System (INIS)

Frantskevich, N.V.; Ulyashin, A.G.; Alifanov, A.V.; Stepanenko, A.V.; Fedotova, V.V.

1999-01-01

The atomic hydrogen effects on the properties of bulk high-temperature superconductors were investigated. It is shown that the insertion of the atomic hydrogen into the bulk of these materials from a DC plasma leads to the increase of the critical current density J c for YBaCuO(123) as well as for BiSrCaCuO(2223) high-temperature superconductors. It is found that the hydrogenation of the He implanted samples with following annealing leads to the optically detected blistering on the surface. It means that the textured thin subsurface layers of high-temperature superconductors can be formed by this method. The improvement of superconductivity by atomic hydrogen can be explained by the passivation of dangling bonds and defects on grain boundaries of these materials

Fracture toughness of Dy123 low porosity bulks at liquid nitrogen temperature

International Nuclear Information System (INIS)

Murakami, A.; Otaka, K.; Miura, T.; Iwamoto, A.

2011-01-01

Fracture toughness values were measured for Dy123 bulks. Fracture toughness was improved by reducing porosity. Fracture toughness values at 77 K were higher than those at room temperature. Fracture toughness was also improved by Ag addition. In order to evaluate the fracture toughness of DyBa 2 Cu 3 O x (Dy123) low porosity bulks, bending tests of V-notched specimens cut from the bulks were carried out. Fracture toughness evaluations of a conventional Dy123 bulk which had pores were also carried out and effects of elimination of pores on the fracture toughness were investigated. Fracture toughness values at 77 K of the low porosity bulks were higher than those of the porous bulk. These fracture toughness values at 77 K were higher than the values at room temperature. Fracture toughness of the low porosity bulk was improved by Ag addition.

Flux-pinning-induced stress and magnetostriction in bulk superconductors

International Nuclear Information System (INIS)

Johansen, Tom H.

2000-01-01

The development of bulk high-temperature superconductors (HTSs) and their applications has today come to a point where the mechanical response to high magnetic fields may be more important than their critical-current density and large-grain property. Reviewed in this article are the recent studies of the magneto-elastic effects which are caused by flux pinning in the superconductors. This includes the work on the giant irreversible magnetostriction and internal stress, which often cause fatal cracking of the HTS bulks as they become magnetized. The cracking is a problem that today accompanies the quest for the highest trapped field values, and the latest development in this area is also presented. While the first part is an overview of experimental efforts, the second summarizes the work done to model the pinning-induced stress and strain under various magnetic and geometrical conditions. (author)

Contamination of YBCO bulk superconductors by samarium and ytterbium

Czech Academy of Sciences Publication Activity Database

Volochová, D.; Jurek, Karel; Radušovská, M.; Piovarči, S.; Antal, V.; Kováč, J.; Jirsa, Miloš; Diko, P.

2014-01-01

Roč. 496, JAN (2014), s. 14-17 ISSN 0921-4534 Institutional support: RVO:68378271 Keywords : YBCO bulk superconductors * critical temperature * critical current density * peak effect Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.942, year: 2014

Induction linear accelerators with high-Tc bulk superconductor lenses

International Nuclear Information System (INIS)

Matsuzawa, Hidenori; Wada, Haruhisa; Mori, Satoshi; Yamamoto, Tadashi

1991-01-01

Solenoidal coils in a one-stage induction accelerator were replaced by a high-T c bulk superconductor lens (Supertron). The accelerator postaccelerated injected electron beams to ∼ 400 keV, ∼ 0.35 kA, and ∼ 10 ns of duration time. (author)

Phonon modes in Gd1-xCexBa2Cu3O7-δ

Directory of Open Access Journals (Sweden)

SH Mozaffari

2009-08-01

Full Text Available  XRD and Raman analyses were performed to probe the phase formation and the variation of the normal phonon frequencies of the high temperature superconductor GdBa2Cu3O7-δ upon Ce doping. It was found that in addition to the orthorhombic 123 phase, some nonsuperconducting peaks, which are mainly due to the BaCeO3 secondary phase, are also formed that suppress the superconducting transition temperature. Besides, analysis of the Raman peaks shows that substitutions of Ce for Gd in GdBa2Cu3O7-δ are restricted to low concentrations in favor of impurity island formation .

Development of application technique of bulk high-Tc superconductor

International Nuclear Information System (INIS)

Hong, Kye Won; Kim, Chan Joong; Kim, Kee Baek; Kwon, Sun Chil; Won, Dong Yun; Lee, Hoh Jin; Lee, Heui Kyoon; Jang, Kun Ik; Yang, Suk Woo

1995-03-01

YBCO-Ag composite superconductors were prepared by extrusion using inorganic binder materials. In the case of the undoped 1-2-3 sample with a dia. of 2.5 mm, critical current density (Jc) was 150 A/cm 2 and current density (Ic) was 10 amps. In the case of the sample with a die. of 4.5 mm, meanwhile, Jc and Ic were 50 A/cm 2 and 32 amps, respectively. Influence of BaCeO 3 addition on magnetization characteristics of melt-textured Y-Ba-Cu-O superconductor was investigated. The variation of magnetization behavior due to the addition of BaCeO 3 is discussed on the basis of the related microstructures. 37 figs, 1 tab, 56 refs. (Author)

Bulk superconductivity in Type II superconductors near the second critical field

DEFF Research Database (Denmark)

Fournais, Søren; Helffer, Bernard

2010-01-01

We consider superconductors of Type II near the transition from the ‘bulk superconducting’ to the ‘surface superconducting’ state. We prove a new L∞ estimate on the order parameter in the bulk, i.e. away from the boundary. This solves an open problem posed by Aftalion and Serfaty [AS]....

Flux Trapping Properties of Bulk HIGH-TC Superconductors in Static Field-Cooling Magnetization

Science.gov (United States)

Deng, Z.; Tsuzuki, K.; Miki, M.; Felder, B.; Hara, S.; Izumi, M.

2013-06-01

The trapping process and saturation effect of trapped magnetic flux of bulk high-temperature superconductors by static field-cooling magnetization (FCM) are reported in the paper. With a cryogenic Bell Hall sensor attached on the center of the bulk surface, the synchronous magnetic signals were recorded during the whole magnetization process. It enables us to know the flux trapping behavior since the removal of the excitation field, as well as the subsequent flux relaxation phenomenon and the flux dissipation in the quench process of the bulk sample. With the help of flux mapping techniques, the relationship between the trapped flux and the applied field was further investigated; the saturation effect of trapped flux was discussed by comparing the peak trapped field and total magnetic flux of the bulk sample. These studies are useful to understand the basic flux trapping properties of bulk superconductors.

New method for introducing nanometer flux pinning centers into single domain YBCO bulk superconductors

International Nuclear Information System (INIS)

Yang, W.M.; Wang, Miao

2013-01-01

Highlights: • Single domain YBCO bulks with Bi 2 O 3 additions fabricated by TSIG process. • Nanoscale Y 2 Ba 4 CuBiOx(YBi2411) particles introduced by Bi 2 O 3 additions. • The YBi2411 particles are about 150 nm, can act as effective flux pinning centers. • The optimal addition of Bi 2 O 3 is 0.7wt% to achieve higher levitation force. • The result is helpful to improve the quality of REBCO bulk superconductors. -- Abstract: Single domain YBCO superconductors with different additions of Bi 2 O 3 have been fabricated by top seeded infiltration and growth process (TSIG). The effect of Bi 2 O 3 additions on the growth morphology, microstructure and levitation force of the YBCO bulk superconductor has been investigated. The results indicate that single domain YBCO superconductors can be fabricated with the additions of Bi 2 O 3 less than 2 wt%; Bi 2 O 3 can be reacted with Y 2 BaCuO 5 and liquid phase and finally form Y 2 Ba 4 CuBiO x (YBi2411) nanoscale particles; the size of the YBi2411 particles is about 100 nm, which can act as effective flux pinning centers. It is also found that the levitation force of single domain YBCO bulks is increasing from 13 N to 34 N and decreasing to 11 N with the increasing of Bi 2 O 3 addition from 0.1 wt% to 0.7 wt% and 2 wt%. This result is helpful for us to improve the physical properties of REBCO bulk superconductors

Improved magnetic-field homogeneity of NMR HTS bulk magnet using a new stacking structure and insertion of an HTS film cylinder into a bulk bore

International Nuclear Information System (INIS)

Itoh, Yoshitaka; Yanagi, Yousuke; Nakamura, Takashi

2017-01-01

A new type of superconducting bulk magnet for compact nuclear magnetic resonance (NMR) devices with high magnetic-field homogeneity has been developed by inserting an HTS film cylinder into a bulk superconductor bore. Annular 60 mmϕ Eu-Ba-Cu-O bulk superconductors with a larger inner diameter (ID) of 36 mm were sandwiched between bulk superconductors with a smaller ID of 28 mm, and the total height of the bulk superconductor set was made to be 120 mm. The inner height of central wide bore space was optimized by magnetic-field simulation so that the influence of the bulk superconductor's paramagnetic moment on applied field homogeneity was minimized during the magnetization process. An HTS film cylinder, in which Gd-Ba-Cu-O tapes were wound helically in three layers around a copper cylinder, was inserted into the bulk bore in order to compensate for the inhomogeneous field trapped by the bulk superconductor. The superconducting bulk magnet composed of the above bulk superconductor set and the film cylinder were cooled by a GM pulse tube refrigerator and magnetized at 4.747 T using the field cooling (FC) method and a conventional superconducting coil magnet adjusted to below 0.5 ppm in magnetic-field homogeneity. The NMR measurement was conducted for an H_2O sample with a diameter of 6.9 mm and a length of 10 mm by setting the sample in the center of the 20 mm ID room-temperature bore of the bulk magnet. The magnetic-field homogeneity derived from the full width at half maximum (FWHM) of the "1H spectrum of H_2O was 0.45 ppm. We confirmed that the HTS film inner cylinder was effective in maintaining the homogeneity of the magnetic field applied in the magnetization process, and as a result, a magnetic field with a homogeneity of less than 1 ppm can be generated in the bore of the bulk magnet without using shim coils. (author)

Superconductors, analysis and applications, with special reference to the utilisation of bulk (Re)BCO materials

Energy Technology Data Exchange (ETDEWEB)

Coombs, T.A., E-mail: tac1000@cam.ac.u [University of Cambridge, Department of Engineering, Trumpington Street, Cambridge CB2 1PZ (United Kingdom)

2010-11-01

The Electrical Power and Energy Conversion (EPEC) superconductivity group at Cambridge University has been working on the application of superconductivity to large scale devices. This work is taking place over a range of areas which cover FCLs, motors and generators, SMES, accelerator magnets and MRI. The research is underpinned by advanced modelling techniques using both pure Critical State models and E-J models to analyse the behaviour of the superconductors. As part of the device design we are concentrating on the analysis of AC losses in complicated geometries such as are found in motor windings and the magnetisation of bulk superconductors to enable their full potential to be realised. We are interested in the full range of high-temperature superconductors and have measured and predicted the performance of YBCO, MgB{sub 2} and BSCCO at a range of temperatures and in wire, tape and bulk forms. This paper concentrates on recent work which includes: modelling of coils using formulations based on H and A. A critical state model for the analysis of coils in SMES; crossed field effects in bulk superconductors; a magnetic model together with experimental results which explain and describe the method of flux pumping whereby a bulk superconductor can be magnetised to a high flux density using a repeatedly applied field of low flux density and finally a new configuration for MRI magnets

Surface flux density distribution characteristics of bulk high-T{sub c} superconductor in external magnetic field

Energy Technology Data Exchange (ETDEWEB)

Torii, S.; Yuasa, K

2004-10-01

Various magnetic levitation systems using oxide superconductors are developed as strong pinning forces are obtained in melt-processed bulk. However, the trapped flux of superconductor is moved by flux creep and fluctuating magnetic field. Therefore, to examine the internal condition of superconductor, the authors measure the dynamic surface flux density distribution of YBCO bulk. Flux density measurement system has a structure with the air-core coil and the Hall sensors. Ten Hall sensors are arranged in series. The YBCO bulk, which has 25 mm diameter and 13 mm thickness, is field cooled by liquid nitrogen. After that, magnetic field is changed by the air-core coil. This paper describes about the measured results of flux density distribution of YBCO bulk in the various frequencies of air-core coils currents.

A superconducting conveyer system using multiple bulk Y-Ba-Cu-O superconductors and permanent magnets

Science.gov (United States)

Kinoshita, T.; Koshizuka, N.; Nagashima, K.; Murakami, M.

Developments of non-contact superconducting devices like superconducting magnetic levitation transfer and superconducting flywheel energy storage system have been performed based on the interactions between bulk Y-Ba-Cu-O superconductors and permanent magnets, in that the superconductors can stably be levitated without any active control. The performances of noncontact superconducting devices are dependent on the interaction forces like attractive forces and stiffness. In the present study, we constructed a non-contact conveyer for which the guide rails were prepared by attaching many Fe-Nd-B magnets onto an iron base plate. Along the translational direction, all the magnets were arranged as to face the same pole, and furthermore their inter-distance was made as small as possible. The guide rail has three magnet rows, for which the magnets were glued on the iron plate such that adjacent magnet rows have opposite poles like NSN. At the center row, the magnetic field at zero gap reached 0.61T, while the field strengths of two rows on the side edges were only 0.48T due to magnetic interactions among permanent magnets. We then prepared a cryogenic box made with FRP that can store several bulk Y-Ba-Cu-O superconductors 25 mm in diameter cooled by liquid nitrogen. It was found that the levitation forces and stiffness increased with increasing the number of bulk superconductors installed in the box, although the levitation force per unit bulk were almost the same. We also confirmed that these forces are dependent on the configuration of bulk superconductors.

Processing of R-Ba-Cu-O superconductors

International Nuclear Information System (INIS)

Wu, H.

1998-01-01

Precipitation processes were developed to introduce second phases as flux pinning centers in Gd-Ba-Cu-O and Nd-Ba-Cu-O superconductors. In Gd-Ba-Cu-O, precipitation is caused by the decrease of the upper solubility limit of Gd 1+x Ba 2-x Cu 3 O 7 solid solution (Gd123ss) in low oxygen partial pressure. Processing of supersaturated Gd 1.2 Ba 1.8 Cu 3 O 7 in low oxygen partial pressure can produce dispersed second phases. Gd211 is formed as a separate phase while extensive Gd124 type stacking fault is formed instead of a separate CuO phase. As a result of the precipitation reaction, the transition temperature and critical current density are increased. In Nd-Ba-Cu-O, precipitation is caused by the decrease of the lower solubility limit of Nd 1+x Ba 2-x Cu 3 O 7 solid solution (Nd123ss) in oxygen. DTA results reveal the relative stability of Nd123ss in different oxygen partial pressures. In 1 bar oxygen partial pressure, Nd123ss with x = 0.1 is the most stable phase. In lower oxygen partial pressures, the most stable composition shifts towards the stoichiometric composition. The relative stability changes faster with decreasing oxygen partial pressure. Therefore, processing in oxygen and air tends to produce broad superconducting transitions but sharp transitions can be achieved in 0.01 bar and 0.001 bar oxygen partial pressures. While the lower solubility limits in 0.01 bar and 0.001 bar oxygen partial pressures remain at x = 0.00, the solubility limits in oxygen and air show a narrowing with decreasing temperature. Because of the narrowing of the solubility range in oxygen, oxygen annealing of Nd123 initially processed in low oxygen partial pressures will result in precipitation of second phases. The equilibrium second phase is BaCuO 2 for temperature above 608 C, and at lower temperatures the equilibrium second phases are Ba 2 CuO 3.3 and Ba 2 Cu 3 O 5+y . However, annealing at low temperature may produce a fine metastable transition phase. A coherent intermediate

Development of high temperature superconductors having high critical current density

International Nuclear Information System (INIS)

Hong, Gye Wong; Kim, C. J.; Lee, H.G.; Kwon, S. C.; Lee, H. J.; Kim, K. B.; Park, J. Y.; Jung, C. H.

2000-08-01

Fabrication of high T c superconductors and its applications for electric power device were carried out for developing superconductor application technologies. High quality YBCO superconductors was fabricated by melt texture growth, top-seeded melt growth process and multi-seeded melt growth process and the properties was compared. The critical current density of the melt processed YBCO superconductors was about few 10,000 A/cm 2 and the levitation force was 50 N. The processing time needed for the growth of the 123 single grain was greatly reduced by applying multi-seeding without no significant degradation of the levitation force. The multi-seeded melt growth process was confirmed as a time-saving and cost-effective method for the fabrication of bulk superconductors with controlled crystallographic orientation

Development of high temperature superconductors having high critical current density

Energy Technology Data Exchange (ETDEWEB)

Hong, Gye Wong; Kim, C. J.; Lee, H.G.; Kwon, S. C.; Lee, H. J.; Kim, K. B.; Park, J. Y.; Jung, C. H

2000-08-01

Fabrication of high T{sub c} superconductors and its applications for electric power device were carried out for developing superconductor application technologies. High quality YBCO superconductors was fabricated by melt texture growth, top-seeded melt growth process and multi-seeded melt growth process and the properties was compared. The critical current density of the melt processed YBCO superconductors was about few 10,000 A/cm{sup 2} and the levitation force was 50 N. The processing time needed for the growth of the 123 single grain was greatly reduced by applying multi-seeding without no significant degradation of the levitation force. The multi-seeded melt growth process was confirmed as a time-saving and cost-effective method for the fabrication of bulk superconductors with controlled crystallographic orientation.

Transport properties of high-temperature superconductors: Surface vs bulk effect

International Nuclear Information System (INIS)

Burlachkov, L.; Koshelev, A.E.; Vinokur, V.M.

1996-01-01

We investigate surface-related transport properties of high-temperature superconductors. We find the mean vortex velocity under applied transport current determined by the activation energies for vortex penetration and exit through the Bean-Livingston barrier. We determine the current distribution between the surfaces of superconductor and the field and current dependencies of the transport activation energies. For a three-dimensional superconductor the transport activation energy, U s 3D , is found to decrease with the external field, H, and transport current, J, as U s 3D ∝H -1/2 and U s 3D ∝J -1/2 , respectively. In the quasi-two-dimensional compounds, U s 2D decays logarithmically with field and current. The interplay between the surface and the bulk contributions to the transport properties, such as current-voltage characteristics, is discussed. copyright 1996 The American Physical Society

An overview of rotating machine systems with high-temperature bulk superconductors

Science.gov (United States)

Zhou, Difan; Izumi, Mitsuru; Miki, Motohiro; Felder, Brice; Ida, Tetsuya; Kitano, Masahiro

2012-10-01

The paper contains a review of recent advancements in rotating machines with bulk high-temperature superconductors (HTS). The high critical current density of bulk HTS enables us to design rotating machines with a compact configuration in a practical scheme. The development of an axial-gap-type trapped flux synchronous rotating machine together with the systematic research works at the Tokyo University of Marine Science and Technology since 2001 are briefly introduced. Developments in bulk HTS rotating machines in other research groups are also summarized. The key issues of bulk HTS machines, including material progress of bulk HTS, in situ magnetization, and cooling together with AC loss at low-temperature operation are discussed.

Morphological stability of Sm123 superconductor during peritectic solidification from Sm211 + L mixture

International Nuclear Information System (INIS)

Sumida, Masaki; Shiohara, Yuh; Umeda, Takateru

2000-01-01

The interface stability of the Sm 123 superconductor was analyzed in accordance with the constitutional undercooling criterion. As the single-crystal growth of the 123 phase is largely dependent on the growth-interface stability, a quantitative analysis was very much required. From this analysis, it was clarified that the constitutional undercooling must exist in the liquid when the 123 growth interface comes close to a 211 particle during the peritectic solidification. It was also predicted that the larger 211 particle radius, smaller volume fraction of the 211 particles, larger growth rate, or smaller imposed temperature gradient would cause easy occurrence of the constitutional undercooling ahead of the 123 growth interface. Taking into account the nucleation at the L/211 interface just ahead of the 123 growth front due to the constitutional undercooling, the transition of 123 growth from a planar-interface morphology to an equiaxed blocky morphology was investigated quantitatively and qualitatively

Effects of seed orientation on the growth behavior of single grain REBCO bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Lee, Hee Gyoun [Korea Polytechnic University, Siheung (Korea, Republic of)

2017-06-15

This study presents a simple method to control the seed orientation which leads to the various growth characteristics of a single grain REBCO (RE: rare-earth elements) bulk superconductors. Seed orientation was varied systematically from c-axis to a-axis with every 30 degree rotation around b-axis. Orientations of a REBCO single grain was successfully controlled by placing the seed with various angles on the prismatic indent prepared on the surface of REBCO powder compacts. Growth pattern was changed from cubic to rectangular when the seed orientation normal to compact surface was varied from c-axis to a-axis. Macroscopic shape change has been explained by the variation of the wetting angle of un-reacted melt depending on the interface energy between YBa2Cu3O7-y (Y123) grain and melt. Higher magnetic levitation force was obtained for the specimen prepared using tilted seed with an angle of 30 degree rotation around b-axis.

Effects of artificial holes in very large single-grain Y_1_._5Ba_2Cu_3O_7_-_y bulk superconductors

International Nuclear Information System (INIS)

Park, S. D.; Jun, B. H.; Kim, C. J.; Park, H. W.

2017-01-01

The effects of artificial holes on the trapped magnetic fields and magnetic levitation forces of very large single-grain Y_1_._5Ba_2Cu_3O_7_-_y (Y1.5) bulk superconductors were studied. Artificial holes were made for Y1.5 powder compacts by die pressing using cylindrical dies with a diameter of 30 mm or 40 m, or rectangular dies with a side length of 50 mm. The single grain Y1.5 bulk superconductors (25 mm, 33 mm in diameter and 42 mm in side length) with artificial holes were fabricated using a top-seeded melt growth (TSMG) process for the die-pressed Y1.5 powder compacts. The magnetic levitation forces at 77 K of the 25 mm single grain Y1.5 samples with one (diameters of 4.2 mm) or six artificial holes (diameters of 2.5 mm) were 10-17% higher than that of the Y1.5 sample without artificial holes. The trapped magnetic fields at 77 K of the Y1.5 samples with artificial holes were also 9.6-18% higher than that of the Y1.5 sample without artificial holes. The 33 mm and 42 mm single grain Y1.5 samples with artificial holes (2.5 mm and 4.2 mm in diameter) also showed trapped magnetic fields 10-13% higher than that of the Y1.5 samples without artificial holes in spite of the reduced superconducting volume fraction due to the presence of artificial holes. The property enhancement in the large single grain Y1.5 bulk superconductors appears to be attributed to the formation of the pore-free regions near the artificial holes and the homogeneous oxygen distribution in the large Y123 grains

The effects of carbon nano filaments (CNT and CNF) doping on high temperature superconductors Y-123

International Nuclear Information System (INIS)

Dadras, S.; Daadmehr, V.

2007-01-01

Full text: This paper is based on the effects of carbon nano filaments (carbon nano tubes and carbon nano fibers) doping on Y-123 studies. We synthesized Y-123 with different contents of CNT and CNF doping. The samples were prepared from powders of Y 2 O 3 , BaCO 3 and Cu O by the solid state reaction. After calcination in air, we mixed Y-123 powder with different percentage of carbon nano filaments weight, produced by the CVD method. For obtaining more homogenous mixing, we have suspended it in an organic solvent with an ultrasonic mixer to prevent agglomeration of CNT. The CNT-Y-123 powder was dried afterwards, and pressed as pellet samples, in about 1mm thick, 10mm diameter, and 1gr weight, and sintered in oxygen atmosphere. We tried to find the transport effects on CNT and CNF doping in 123 systems. The strong coupling between grains in CNT doped samples caused the flow of inter-granular currents. Therefore the presence of CNT in high temperature superconductor samples increases the critical current density. Among various carbon precursors, carbon nano tubes (CNT) are very interesting because of their nano meter diameter which may make them as effective pinning centers, compared to the ordinary carbon. The carbon nano tubes are functioning like columnar defects produced by heavy-ion irradiation. Nano phase particles or aggregates embodied in the superconductor matrix can pin the flux lines effectively and enhance the intra-grain transport critical current density in high applied magnetic fields. Nano phase size particles in the size range of about 5-10 nm can be used as flux pinning centers for low field applications. The effects of carbon and carbon dioxide in Y-123 were studied by several groups, but none of them argued the effects of carbon nano tubes doping on Y-123. Uno et al. found that Jc was related to the carbon concentration, but they showed that Tc value and other physical properties did not change. In carbon doped Y-123 samples, Tc decreases with

Thermal stability and magnetocaloric properties of GdDyAlCo bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Liang, L. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Hui, X. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)], E-mail: huixd01@hotmail.com; Chen, G.L. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

2008-01-25

Gd{sub 56-x}Dy{sub x}Al{sub 24}Co{sub 20} (x = 16, 20 and 22) bulk metallic glasses (BMGs) alloys with a diameter of 2, 3 and 3 mm, respectively, were prepared by using copper mold casting. These alloys exhibit higher values of the glass transition temperature, crystallization temperature, and activation energy of the glass transition and crystallization, compared with those of other known rare-earth-based BMGs. A maximum magnetic entropy changes of 15.78 J/(kg K) is obtained in Gd{sub 40}Dy{sub 16}Al{sub 24}Co{sub 20}, which is the maximal among all the bulk metallic glasses, and is much larger than those of the known crystalline magnetic refrigerant compound Gd{sub 5}Si{sub 2}Ge{sub 1.9}Fe{sub 0.1} and pure Gd metal. All the three BMG alloys have a broader temperature range of the entropy change peak, resulting in larger refrigerate capacities (RC) than those of conventional crystalline materials. The excellent magnetocaloric properties combining with high thermal stability make them an attractive candidate for magnetic refrigerants in the temperature range of 20-100 K.

Measurement of electromagnetic force between multiple bulk superconductors; Fukusu no barukutai chodendotai to eikyujishakukairo niokeru denjiryoku sokutei

Energy Technology Data Exchange (ETDEWEB)

Otani, T.; Murakami, M. [Superconductivity Research Laboratory, Tokyo (Japan); Nagashima, K. [Railway Technical Research Institute, Tokyo (Japan); Murayama, M. [Shikoku Ekectric Power Co., Inc., Kagawa (Japan)

1999-11-25

The electromagnetic force (EMF) that is exhibited by the interaction between bulk superconductors and permanent magnets is used for magnetic levitation devices. To facilitate such applications, it is necessary to enhance the EMF. We measured the EMF for Y-Ba-Cu-O superconductors with different shapes and dimensions by varying the structure of disk magnets such as their thickness and the number of poles. The EMF is strongly dependent on the magnet structure as long as permanent magnets and good quality bulk superconductors are used. Thus, for the design of practical devices, it is important to optimize the magnet structure. (author)

Simulation of Field Dependence of Critical Current Densities of Bulk High Tc Superconducting Materials regarding Thermally Activated Flux Motion

Science.gov (United States)

Santosh, M.; Naik, S. Pavan Kumar; Koblischka, M. R.

2017-07-01

In the upcoming generation, bulk high temperature superconductors (HTS) will play a crucial and a promising role in numerous industrial applications ranging from Maglev trains to magnetic resonance imaging, etc. Especially, the bulk HTS as permanent magnets are suitable due to the fact that they can trap magnetic fields being several orders of magnitude higher than those of the best hard ferromagnets. The bulk HTS LREBa2Cu3O7-δ (LREBCO or LRE-123, LRE: Y, Gd, etc.,) materials could obtain very powerful compact superconducting super-magnets, which can be operated at the cheaper liquid nitrogen temperature or below due to higher critical temperatures (i.e., ∼90 K). As a result, the new advanced technology can be utilized in a more attractive manner for a variety of technological and medical applications which have the capacity to revolutionize the field. An understanding of the magnetic field dependence of the critical current density (J c(H)) is important to develop better adapted materials. To achieve this goal, a variety of Jc (H) behaviours of bulk LREBCO samples were modelled regarding thermally activated flux motion. In essence, the Jc (H) curves follows a certain criterion where an exponential model is applied. However, to fit the complete Jc (H) curve of the LRE-123 samples an unique model is necessary to explain the behavior at low and high fields. The modelling of the various superconducting materials could be understood in terms of the pinning mechanisms.

Progress in melt-texturing of YBCO superconductors

International Nuclear Information System (INIS)

Salama, K.; Lee, D.F.; Selvamanickam, V.

1993-01-01

Since the discovery of high temperature superconductors (HTS), tremendous efforts have been expanded toward the improvement of these materials. Due to the weak-link problem associated with grain boundaries, sintered bulk HTS possess a transport critical current density (J c ) on the order of 10 2 -10 3 A/cm 2 at 77 K. While these sintered superconductors may be utilized in low current applications, novel processing methods have to be developed to obtain HTS that can sustain high currents. Melt-texturing of HTS was found to result in a high degree of grain orientation, and is presently the most prominent processing method used to manufacture bulk YBa 2 Cu 3 O x (123) with superior transport and magnetic properties. In this review paper, various melt-texturing methods will be discussed, and the variation in J c with processing will be presented. (orig.)

Enhancement of magnetic coupling between permanent magnets and bulk superconductors through iron embedding

International Nuclear Information System (INIS)

Seki, H.; Kurabayashi, H.; Suzuki, A.; Ikeda, M.; Akiyama, S.; Murakami, M.

2009-01-01

Magnetic torque can be transferred without contact through the coupling of permanent magnets (PM) and bulk superconductors (BSC). For this purpose, permanent magnets should have multiple pole configuration like NSNS. The magnitude of the transferable torque depends on the field strength and the gap between PM and BSC. It was found that the torque decays quickly with the gap. In order to enhance the strength of transferable magnetic torque, we prepared bulk Y-Ba-Cu-O superconductors for which Fe bars are embedded. Holes about 1 mm in diameter were mechanically drilled into bulk Y-Ba-Cu-O, and Fe bars about 0.9 mm in diameter were inserted followed by impregnation of Bi-Pb-Sn alloys with low melting points. The composite of Y-Ba-Cu-O and Fe bars attract magnetic fields generated from permanent magnet before cooling, and thereby magnetic coupling will be improved. We have found that the magnetic torque force can be greatly enhanced through iron embedding.

Deformation of high-temperature superconductors

International Nuclear Information System (INIS)

Goretta, K.C.; Routbort, J.L.; Miller, D.J.; Chen, N.; Dominguez-Rodriguez, A.; Jimenez-Melendo, M.; De Arellano-Lopez, A.R.

1994-08-01

Of the many families of high-temperature superconductors, only the properties of those discovered prior to 1989 - Y-Ba-Cu-O, Tl-Ba(Sr)-Ca-Cu-O, and Bi(Pb)-Sr-Ca-Cu-O - have been studied extensively. Deformation tests have been performed on YBa 2 Cu 3 O x (Y-123), YBa 2 Cu 4 O x (Y-124), TlBa 2 Ca 2 Cu 3 O x (Bi-2223). The tests have revealed that plasticity is generally limited in these compounds and that the rate-controlling diffusional kinetics for creep are very slow. Nevertheless, hot forming has proved to be quite successful for fabrication of bulk high-temperature superconductors, so long as deformation rates are low or large hydrostatic stresses are applied. Steady-state creep data have proved to be useful in designing optimal heat treatments for superconductors and in support of more-fundamental diffusion experiments. The high-temperature superconductors are highly complex oxides, and it is a challenge to understand their deformation responses. In this paper, results of interest and operant creep mechanisms will be reviewed

Magnetic levitation and its application for education devices based on YBCO bulk superconductors

International Nuclear Information System (INIS)

Yang, W.M.; Chao, X.X.; Guo, F.X.; Li, J.W.; Chen, S.L.

2013-01-01

Highlights: • A small superconducting maglev propeller system has been designed and constructed based on YBCO bulk superconductors. • Several small maglev vehicle models have been designed and constructed based on YBCO bulk superconductors. • The models can be used as experimental or demonstration devices for the magnetic levitation applications. -- Abstract: A small superconducting maglev propeller system, a small spacecraft model suspending and moving around a terrestrial globe, several small maglev vehicle models and a magnetic circuit converter have been designed and constructed. The track was paved by NdFeB magnets, the arrangement of the magnets made us easy to get a uniform distribution of magnetic field along the length direction of the track and a high magnetic field gradient in the lateral direction. When the YBCO bulks mounted inside the vehicle models or spacecraft model was field cooled to LN 2 temperature at a certain distance away from the track, they could be automatically floating over and moving along the track without any obvious friction. The models can be used as experimental or demonstration devices for the magnetic levitation applications

Magnetic levitation and its application for education devices based on YBCO bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Yang, W.M., E-mail: yangwm@snnu.edu.cn; Chao, X.X.; Guo, F.X.; Li, J.W.; Chen, S.L.

2013-10-15

Highlights: • A small superconducting maglev propeller system has been designed and constructed based on YBCO bulk superconductors. • Several small maglev vehicle models have been designed and constructed based on YBCO bulk superconductors. • The models can be used as experimental or demonstration devices for the magnetic levitation applications. -- Abstract: A small superconducting maglev propeller system, a small spacecraft model suspending and moving around a terrestrial globe, several small maglev vehicle models and a magnetic circuit converter have been designed and constructed. The track was paved by NdFeB magnets, the arrangement of the magnets made us easy to get a uniform distribution of magnetic field along the length direction of the track and a high magnetic field gradient in the lateral direction. When the YBCO bulks mounted inside the vehicle models or spacecraft model was field cooled to LN{sub 2} temperature at a certain distance away from the track, they could be automatically floating over and moving along the track without any obvious friction. The models can be used as experimental or demonstration devices for the magnetic levitation applications.

Development of fabrication technique of bulk high superconductor

International Nuclear Information System (INIS)

Hong, Gye Won; Kim, Chang Joong; Kim, Ki Baik; Lee, Ho Jin; Lee, Hee Gyoun; Kwon, Sun Chil.

1997-05-01

In order to realize the commercial application of HTSC materials, it is necessary to develop the fabrication process of high Tc oxide superconductor materials with desired shape and for practical application and high critical current density as well as good mechanical strength which critical current density as well as good mechanical strength which can withstand high lorenz force generated at high magnetic field. Much studies have been concentrated to develop the fabrication technique for high critical current density but still there are a lot of gap which should be overcome for large scale application of HTSC materials at liquid nitrogen temperature. Recently some new fabrication techniques have been developed for YBCO bulk superconductor with high mechanical strength and critical current density. In this project, plastic extrusion and melt process techniques were studied. The components materials for the current lead and the flywheel application were fabricated and their characteristics were investigated from the view point of microstructure and phase formation during heat treatment process. (author). 64 refs., 59 figs

Pressure effects on the carbon nano-tube embedded Y-123 superconductors

Energy Technology Data Exchange (ETDEWEB)

Dadras, Sedigheh, E-mail: dadras@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran 1993893973 (Iran, Islamic Republic of); Manivannan, Nallayian [CeNSCMR & FPRD, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of); Daadmehr, Vahid [Department of Physics, Alzahra University, Tehran 1993893973 (Iran, Islamic Republic of); Rezakhani, Ali Tayefeh [Department of Physics, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Kim, Kee Hoon [CeNSCMR & FPRD, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of)

2016-04-15

It has been known that applying pressure and doping carbon nano-tubes (CNTs) can each affect the behavior of high temperature superconductors. Here, bridging these two effects in order to see how they can interplay, we investigate how the dc resistivity varies in both pure and CNT-doped polycrystalline YBa{sub 2}Cu{sub 3}O{sub 7−δ} (Y-123) compounds under hydrostatic pressure. We demonstrate that the broadening of the resistivity transition in the CNT-doped samples (of 0.7 wt%) is smaller than the undoped samples. In addition, by increasing applied pressure, the doped samples exhibit a higher rate of the increase of the transition temperatures T{sub c}{sup on} and T{sub c}{sup mid} than the undoped samples. Interestingly as well, under applied pressure of 1.5 GPa, it is found that T{sub c}{sup on} for the doped samples (99.39 K) is relatively higher than in the undoped samples (96.88 K). The doped samples also show more robustness versus applied pressure in the sense that they have smaller variations of resistivity. In particular, we observed that the increase rate of the normal resistivity in the CNT-doped samples is nearly four times smaller than the undoped samples. This may be a manifestation of relative robustness of the doped samples against fractures of the links between grains. These observations, overall, may suggest that the CNT doping, due to unique mechanical characteristics of CNTs, can enhance superconductivity properties of Y-123 superconductors under applied pressure.

Maximum repulsed magnetization of a bulk superconductor with low pulsed field

International Nuclear Information System (INIS)

Tsuchimoto, M.; Kamijo, H.; Fujimoto, H.

2005-01-01

Pulsed field magnetization of a bulk high-T c superconductor (HTS) is important technique especially for practical applications of a bulk superconducting magnet. Full magnetization is not obtained for low pulsed field and trapped field is decreased by reversed current in the HTS. The trapped field distribution by repulsed magnetization was previously reported in experiments with temperature control. In this study, repulsed magnetization technique with the low pulsed field is numerically analyzed under assumption of variable shielding current by the temperature control. The shielding current densities are discussed to obtain maximum trapped field by two times of low pulsed field magnetizations

Effects of artificial holes in very large single-grain Y{sub 1.5}Ba{sub 2}Cu{sub 3}O{sub 7-y} bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Park, S. D.; Jun, B. H.; Kim, C. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, H. W. [Korea University of Technology and Education, Cheonan (Korea, Republic of)

2017-09-15

The effects of artificial holes on the trapped magnetic fields and magnetic levitation forces of very large single-grain Y{sub 1.5}Ba{sub 2}Cu{sub 3}O{sub 7-y} (Y1.5) bulk superconductors were studied. Artificial holes were made for Y1.5 powder compacts by die pressing using cylindrical dies with a diameter of 30 mm or 40 m, or rectangular dies with a side length of 50 mm. The single grain Y1.5 bulk superconductors (25 mm, 33 mm in diameter and 42 mm in side length) with artificial holes were fabricated using a top-seeded melt growth (TSMG) process for the die-pressed Y1.5 powder compacts. The magnetic levitation forces at 77 K of the 25 mm single grain Y1.5 samples with one (diameters of 4.2 mm) or six artificial holes (diameters of 2.5 mm) were 10-17% higher than that of the Y1.5 sample without artificial holes. The trapped magnetic fields at 77 K of the Y1.5 samples with artificial holes were also 9.6-18% higher than that of the Y1.5 sample without artificial holes. The 33 mm and 42 mm single grain Y1.5 samples with artificial holes (2.5 mm and 4.2 mm in diameter) also showed trapped magnetic fields 10-13% higher than that of the Y1.5 samples without artificial holes in spite of the reduced superconducting volume fraction due to the presence of artificial holes. The property enhancement in the large single grain Y1.5 bulk superconductors appears to be attributed to the formation of the pore-free regions near the artificial holes and the homogeneous oxygen distribution in the large Y123 grains.

Concepts for using trapped-flux bulk high-temperature superconductor in motors and generators

International Nuclear Information System (INIS)

Hull, John R; Strasik, Michael

2010-01-01

We review previous concepts for using bulk high-temperature superconductors (HTSs) in motors and generators and discuss methods for using trapped-flux (TF) HTSs in motors and generators that have been recently investigated in our laboratory. We examine the expected performance of a brushless motor/generator that uses TF bulk HTSs to provide magnetomotive force, where the stator windings are used to create the TF. A key feature is the use of dysprosium for the stator and rotor cores.

Possible charge analogues of spin transfer torques in bulk superconductors

Science.gov (United States)

Garate, Ion

2014-03-01

Spin transfer torques (STT) occur when electric currents travel through inhomogeneously magnetized systems and are important for the motion of magnetic textures such as domain walls. Since superconductors are easy-plane ferromagnets in particle-hole (charge) space, it is natural to ask whether any charge duals of STT phenomena exist therein. We find that the superconducting analogue of the adiabatic STT vanishes in a bulk superconductor with a momentum-independent order parameter, while the superconducting counterpart of the nonadiabatic STT does not vanish. This nonvanishing superconducting torque is induced by heat (rather than charge) currents and acts on the charge (rather than spin) degree of freedom. It can become significant in the vicinity of the superconducting transition temperature, where it generates a net quasiparticle charge and alters the dispersion and linewidth of low-frequency collective modes. This work has been financially supported by Canada's NSERC.

Development of superconducting magnetic bearing using superconducting coil and bulk superconductor

Energy Technology Data Exchange (ETDEWEB)

Seino, H; Nagashima, K; Arai, Y [Railway Technical Research Institute, Hikari-cho 2-8-38, Kokubunji-shi, Tokyo (Japan)], E-mail: seino@rtri.or.jp

2008-02-01

The authors conducted a study on superconducting magnetic bearing, which consists of superconducting rotor and stator to apply the flywheel energy-storage system for railways. In this study, high temperature bulk superconductor (HTS bulk) was combined with superconducting coils to increase the load capacity of the bearing. In the first step of the study, the thrust rolling bearing was selected for application by using liquid nitrogen cooled HTS bulk. 60mm-diameter HTS bulks and superconducting coil which generated a high gradient of magnetic field by cusp field were adopted as a rotor and a stator for superconducting magnetic bearing, respectively. The results of the static load test and the rotation test, creep of the electromagnetic forces caused by static flux penetration and AC loss due to eccentric rotation were decreased to the level without any problems in substantial use by using two HTS bulks. In the result of verification of static load capacity, levitation force (thrust load) of 8900N or more was supportable, and stable static load capacity was obtainable when weight of 460kg was levitated.

Development of superconducting magnetic bearing using superconducting coil and bulk superconductor

International Nuclear Information System (INIS)

Seino, H; Nagashima, K; Arai, Y

2008-01-01

The authors conducted a study on superconducting magnetic bearing, which consists of superconducting rotor and stator to apply the flywheel energy-storage system for railways. In this study, high temperature bulk superconductor (HTS bulk) was combined with superconducting coils to increase the load capacity of the bearing. In the first step of the study, the thrust rolling bearing was selected for application by using liquid nitrogen cooled HTS bulk. 60mm-diameter HTS bulks and superconducting coil which generated a high gradient of magnetic field by cusp field were adopted as a rotor and a stator for superconducting magnetic bearing, respectively. The results of the static load test and the rotation test, creep of the electromagnetic forces caused by static flux penetration and AC loss due to eccentric rotation were decreased to the level without any problems in substantial use by using two HTS bulks. In the result of verification of static load capacity, levitation force (thrust load) of 8900N or more was supportable, and stable static load capacity was obtainable when weight of 460kg was levitated

Feasibility of introducing ferromagnetic materials to onboard bulk high-Tc superconductors to enhance the performance of present maglev systems

Science.gov (United States)

Deng, Zigang; Wang, Jiasu; Zheng, Jun; Zhang, Ya; Wang, Suyu

2013-02-01

Performance improvement is a long-term research task for the promotion of practical application of promising high-temperature superconducting (HTS) magnetic levitation (maglev) vehicle technologies. We studied the feasibility to enhance the performance of present HTS Maglev systems by introducing ferromagnetic materials to onboard bulk superconductors. The principle here is to make use of the high magnetic permeability of ferromagnetic materials to alter the flux distribution of the permanent magnet guideway for the enhancement of magnetic field density at the position of the bulk superconductors. Ferromagnetic iron plates were added to the upper surface of bulk superconductors and their geometric and positioning effects on the maglev performance were investigated experimentally. Results show that the guidance performance (stability) was enhanced greatly for a particular setup when compared to the present maglev system which is helpful in the application where large guidance forces are needed such as maglev tracks with high degrees of curves.

Changes of soft X-ray emission spectra of oxygen and copper in high Tc superconductors

International Nuclear Information System (INIS)

Fukushima, Sei; Gohshi, Yohichi; Kohiki, Shigemi; Saitoh, Naoki

1989-01-01

X-ray induced soft X-ray emission spectroscopy is one of the bulk analysis methods used to characterize high-Tc superconductor. In this report, some observations on the changes in O Kα and Cu L spectra of thin layer LnBa 2 Cu 3 O 7-δ (Ln=Er,Gd) samples are presented. From the measurement of O Kα, no discernible difference was found between those of Gd compounds which were composed single phase or not. It may be said that the electronic structure of p state localized on the O is not sensitive to the change of Tc or zero-resistance temperature. From the measurement of Cu L spectra, it was found that Cu Lα of only Gd containing compounds has a low energy shoulder

Transport current anisotropy in oriented grained bulk YBa2Cu3Ox superconductor

International Nuclear Information System (INIS)

Selvamanickam, V.; Salama, K.

1990-01-01

The anisotropy in transport current density has been studied on bulk YBa 2 Cu 3 O x superconductor. The transport current density measurements were performed on oriented grained YBa 2 Cu 3 O x superconductor with the current aligned at different angles to the a endash b plane. The angular dependence of J c shows a rapid drop when the transport current is misaligned from the a endash b plane at small angles and then a slow decrease at higher angles. An anisotropy ratio of about 25 is observed at 77 K and zero field between the J c along a endash b plane and that perpendicular to the plane

Doped Tl-1212 and Tl-1223 superconductors

International Nuclear Information System (INIS)

Eder, M.H.

2001-09-01

This work describes the preparation and characterization of thallium-lead-strontium-barium-calcium-(uranium)-copperoxide (Tl-1212, Tl-1223) high-temperature superconductors. The precursors were prepared via nitrate method. After calcination the oxidic powders were mixed with stoichiometric amounts of an Tl 2 O 3 , PbO, Er 2 O 3 and Gd 2 O 3 by milling and afterwards uniaxial compressed. Sintering was carried out in silver foils. X-ray diffractometry and high-resolution microscopy in combination with scanning electron microscopy (including EDAX) were used to study the influence of varying thallium/lead-, strontium/barium-, calcium/rare earth element ratios and the effect of uranium on the phase composition and microstructure of bulk superconductors. Furthermore the influence of the composition on the electrical and magnetical properties was studied. On phase pure Tl-1212 and Tl-1223 superconductors NMR-measurements were done. Small amounts of gadolinium and erbium instead of calcium and excess-uranium have a positive impact on the electrical and magnetical properties of the Tl-1223 superconductors. Higher amounts of these doping elements favor the Tl-1212 phase. Tl-1212 superconductors with varying thallium/lead- strontium/barium- and calcium/gadolinium ratios were prepared phasepure in wide range of doping. Transition temperatures up to 96 K were achieved. It was shown that lead has an oxidation number of +4 and thallium of +3. (author)

Mechanical reliability of bulk high Tc superconductors

International Nuclear Information System (INIS)

Freiman, S.W.

1990-01-01

Most prospective applications for high T c superconductors in bulk form, e.g. magnets, motors, will require appreciable mechanical strength. Work at NIST [National Institute of Standards and Technology] has begun to address issues related to mechanical reliability. For example, recent studies on Ba-Y-Cu-O have shown that the intrinsic crack growth resistance, K IC , of crystals of this material is even smaller than was first reported, less than that of window glass, and is sensitive to moisture. Processing conditions, particularly sintering and annealing atmosphere, have been shown to have a major influence on microstructure and internal stresses in the material. Large internal stresses result from the tetragonal to orthorhombic phase transformation as well as the thermal expansion anisotropy in the grains of the ceramic. Because stress relief is absent, microcracks form which have a profound influence on strength

Stoner vs. spin-mixing behavior in the bulk magnetism of Gd: A spin ...

Indian Academy of Sciences (India)

bulk magnetism of Gd: A spin-resolved photoemission study. K MAITI1,2,∗. , M C MALAGOLI2, A DALLMEYER2 and C CARBONE2,3. 1Tata Institute of Fundamental Research, Homi Bhabha Road, Mumbai 400 005, India. 2Institut für Festkörperforschung, Forschungszentrum Jülich, D-52428 Jülich, Germany. 3Consiglio ...

Feasibility of introducing ferromagnetic materials to onboard bulk high-Tc superconductors to enhance the performance of present maglev systems

International Nuclear Information System (INIS)

Deng, Zigang; Wang, Jiasu; Zheng, Jun; Zhang, Ya; Wang, Suyu

2013-01-01

Highlights: ► Ferromagnetic materials guide the flux distribution of the PMG to bulk positions. ► With ferromagnetic materials, guidance performance can be enhanced greatly. ► A new HTS Maglev system with onboard ferromagnetic materials is designed. ► The design can meet large guidance force requirements for practical applications. -- Abstract: Performance improvement is a long-term research task for the promotion of practical application of promising high-temperature superconducting (HTS) magnetic levitation (maglev) vehicle technologies. We studied the feasibility to enhance the performance of present HTS Maglev systems by introducing ferromagnetic materials to onboard bulk superconductors. The principle here is to make use of the high magnetic permeability of ferromagnetic materials to alter the flux distribution of the permanent magnet guideway for the enhancement of magnetic field density at the position of the bulk superconductors. Ferromagnetic iron plates were added to the upper surface of bulk superconductors and their geometric and positioning effects on the maglev performance were investigated experimentally. Results show that the guidance performance (stability) was enhanced greatly for a particular setup when compared to the present maglev system which is helpful in the application where large guidance forces are needed such as maglev tracks with high degrees of curves

A small Maglev car model using YBCO bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Yang, W M [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China); Zhou, L [Northwest Institute for Nonferrous Metal Research, PO Box 51, Xi' an, Shaanxi 710016 (China); Yong, Feng [Northwest Institute for Nonferrous Metal Research, PO Box 51, Xi' an, Shaanxi 710016 (China); Zhang, P X [Northwest Institute for Nonferrous Metal Research, PO Box 51, Xi' an, Shaanxi 710016 (China); Chao, X X [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China); Bian, X B [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China); Zhu, S H [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China); Wu, X L [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China); Liu, P [Department of Physics, Shaanxi Normal University, Xi' an, Shaanxi 710016 (China)

2006-07-15

Models of two small Maglev cars have been made. The track was paved with NdFeB magnets. The arrangement of the magnets made it easy to get a uniform magnetic field distribution along the length of the track and a magnetic field gradient in the lateral direction. When the car with YBCO bulk superconductors was field cooled to LN{sub 2} temperature at a certain distance above the track, the car could be automatically levitated over the track and moved along the track without any obvious friction. The model can be used to demonstrate the Meissner effect and a fast transportation system to students and adults.

A small Maglev car model using YBCO bulk superconductors

International Nuclear Information System (INIS)

Yang, W M; Zhou, L; Yong, Feng; Zhang, P X; Chao, X X; Bian, X B; Zhu, S H; Wu, X L; Liu, P

2006-01-01

Models of two small Maglev cars have been made. The track was paved with NdFeB magnets. The arrangement of the magnets made it easy to get a uniform magnetic field distribution along the length of the track and a magnetic field gradient in the lateral direction. When the car with YBCO bulk superconductors was field cooled to LN 2 temperature at a certain distance above the track, the car could be automatically levitated over the track and moved along the track without any obvious friction. The model can be used to demonstrate the Meissner effect and a fast transportation system to students and adults

Gap-related trapped magnetic flux dependence between single and combined bulk superconductors

Science.gov (United States)

Deng, Z.; Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Uetake, T.; Izumi, M.

2011-05-01

Aiming at examining the trapped-flux dependence between single and combined bulk superconductors for field-pole applications, three rectangular Y 1.65Ba 2Cu 3O 7-x (YBCO) bulks with a possibly compact combination were employed to investigate the trapped-flux characteristics of single and combined bulks with a field-cooling magnetization (FCM) method. A gap-related dependence was found between them. At lower gaps of 1 mm and 5 mm, the peak trapped fields and total magnetic flux of combined bulks are both smaller than the additive values of each single bulk, which can be ascribed to the demagnetization influences of the field around the bulk generated by the adjacent ones. While, at larger gaps like 10 mm, the situation becomes reversed. The combined bulks can attain bigger peak trapped fields as well as total magnetic flux, which indicates that the magnetic field by the bulk combination can reach higher gaps, thanks to the bigger magnetic energy compared with the single bulk. The presented results show that, on one hand, it is possible to estimate the total trapped magnetic flux of combined bulks by an approximate additive method of each single bulk while considering a demagnetization factor; on the other hand, it also means that the performance of combined bulks will be superior to the addition of each single bulk at larger gaps, thus preferable for large-scaled magnet applications.

Clean bulk YBaCuO superconductors doped by paramagnetic ions of Sm and Yb

Czech Academy of Sciences Publication Activity Database

Jirsa, Miloš; Volochová, D.; Kováč, J.; Diko, P.

2017-01-01

Roč. 131, č. 4 (2017), s. 1027-1029 ISSN 0587-4246 Institutional support: RVO:68378271 Keywords : YBaCuO * bulk superconductors * paramagnetic ions * microstructure * vortex pinning Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 0.469, year: 2016

Flux pinning and superconducting properties of melt-textured NEG-123 superconductor with TiO.sub.2./sub. addition

Czech Academy of Sciences Publication Activity Database

Muralidhar, M.; Jirsa, Miloš; Tomita, M.

2010-01-01

Roč. 470, 13-14 (2010), s. 592-597 ISSN 0921-4534 R&D Projects: GA ČR GA202/08/0722 Institutional research plan: CEZ:AV0Z10100520 Keywords : flux pinning, NEG-123 * high-Tc superconductors * high temperature levitation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.407, year: 2010

Transport current anisotropy in oriented grained bulk YBa2Cu3O(x) superconductor

International Nuclear Information System (INIS)

Selvamanickam, V.; Salama, K.

1990-01-01

The anisotropy in transport current density has been studied on bulk YBa2Cu3O(x) superconductor. The transport current density measurements were performed on oriented grained YBa2Cu3O(x) superconductor with the current aligned at different angles to the a-b plane. The angular dependence of Jc shows a rapid drop when the transport current is misaligned from the a-b plane at small angles and then a slow decrease at higher angles. An anisotropy ratio of about 25 is observed at 77 K and zero field between the Jc along a-b plane and that perpendicular to the plane. 15 refs

Correlation between structural, electrical and magnetic properties of GdMnO3 bulk ceramics

International Nuclear Information System (INIS)

Samantaray, S.; Mishra, D.K.; Pradhan, S.K.; Mishra, P.; Sekhar, B.R.; Behera, Debdhyan; Rout, P.P.; Das, S.K.; Sahu, D.R.; Roul, B.K.

2013-01-01

This paper reports the effect of sintering temperature on ferroelectric properties of GdMnO 3 (GMO) bulk ceramics at room temperature prepared by the conventional solid state reaction route following slow step sintering schedule. Ferroelectric hysteresis loop as well as sharp dielectric anomaly in pure (99.999%) GMO sintered ceramics has been clearly observed. Samples sintered at 1350 °C become orthorhombic with Pbnm space group and showed frequency independent sharp dielectric anomalies at 373 K and a square type of novel ferroelectric hysteresis loop was observed at room temperature. Interestingly, dielectric anomalies and ferroelectric behavior were observed to be dependent upon sintering temperature of GdMnO 3 . Room temperature dielectric constant (ε r ) value at different frequencies is observed to be abnormally high. The magnetic field and temperature dependent magnetization show antiferromagnetic behavior at 40 K for both 1350 °C and 1700 °C sintered GMO. Present findings showed the possibility of application of GdMnO 3 at room temperature as multifunctional materials. - Highlights: • Preparation of single-phasic polycrystalline GdMnO 3 sample by the solid state sintering route. • Observation of square type P–E hysteresis loop with higher saturation and remnant polarization. • Observation of antiferromagnetic behavior at 40 K in polycrystalline GdMnO 3 . • Possibility of room temperature application of GdMnO 3 as multifunctional material

Effects of seed geometry on the crystal growth and the magnetic properties of single grain REBCO bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Lee, Hwi Joo; Lee, Hee Gyoun [Korea Polytechnic University, Siheung (Korea, Republic of); Park, Soon Dong; Jun, Bung Hyack; Kim, Chan Joong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-09-15

This study presents that the orientation and the geometry of seed affect on the growth behavior of melt processed single grain REBCO bulk superconductor and its magnetic properties. The effects of seed geometry have been investigated for thin 30mm x 30mm rectangular powder compacts. Single grain REBCO bulk superconductors have been grown successfully by a top seed melt growth method for 8-mm thick vertical thin REBCO slab. Asymmetric structures have been developed at the front surface and at the rear surface of the specimen. Higher magnetic properties have been obtained for the specimen that c-axis is normal to the specimen surface. The relationships between microstructure, grain growth and magnetic properties have been discussed.

Doping-Induced Isotopic Mg11B2 Bulk Superconductor for Fusion Application

Directory of Open Access Journals (Sweden)

Qi Cai

2017-03-01

Full Text Available Superconducting wires are widely used for fabricating magnetic coils in fusion reactors. Superconducting magnet system represents a key determinant of the thermal efficiency and the construction/operating costs of such a reactor. In consideration of the stability of 11B against fast neutron irradiation and its lower induced radioactivation properties, MgB2 superconductor with 11B serving as the boron source is an alternative candidate for use in fusion reactors with a severe high neutron flux environment. In the present work, the glycine-doped Mg11B2 bulk superconductor was synthesized from isotopic 11B powder to enhance the high field properties. The critical current density was enhanced (103 A·cm−2 at 20 K and 5 T over the entire field in contrast with the sample prepared from natural boron.

Pulsed-Field Magnetization Properties of Bulk Superconductors by Employment of Vortex-Type Coils

Science.gov (United States)

Deng, Z.; Shinohara, N.; Miki, M.; Felder, B.; Tsuzuki, K.; Watasaki, M.; Kawabe, S.; Taguchi, R.; Izumi, M.

Vortex-type magnetizing coils are gaining more and more attention to activate bulk superconductors in pulsed-field magnetization (PFM) studies, compared with solenoid-type ones. Following existing reports, we present experimental results of the different penetration patterns of magnetic flux between the two kinds of coils. It was found that the magnetic flux will primarily penetrate inside the bulk from the upper and lower surfaces by using vortex coils, rather than from the periphery in the case of solenoid coils. Moreover, the bulk submitted to a small pulsed-field excitation exhibits a similar field profile as the excitation field (convex or concave shape); a phenomenon named field memory effect. The use of vortex- or solenoid-type coils in PFM will pose an influence on the initial flux penetration patterns during the flux trapping processes, but both coils can finally excite the best conical trapped field shape of the bulk.

Maglev performance of a double-layer bulk high temperature superconductor above a permanent magnet guideway

International Nuclear Information System (INIS)

Deng, Z; Wang, J; Zheng, J; Lin, Q; Zhang, Y; Wang, S

2009-01-01

In order to improve the performance of the present high temperature superconducting (HTS) maglev vehicle system, the maglev performance of single- and double-layer bulk high temperature superconductors (HTSC) was investigated above a permanent magnet guideway (PMG). It is found that the maglev performance of a double-layer bulk HTSC is not a simple addition of each layer's levitation and guidance force. Moreover, the applied magnetic field at the position of the upper layer bulk HTSC is not completely shielded by the lower layer bulk HTSC either. 53.5% of the levitation force and 27.5% of the guidance force of the upper layer bulk HTSC are excited in the double-layer bulk HTSC arrangement in the applied field-cooling condition and working gap, bringing a corresponding improvement of 16.9% and 8.8% to the conventional single-layer bulk HTSC. The present research implies that the cost performance of upper layer bulk HTSC is a little low for the whole HTS maglev system.

Maglev performance of a double-layer bulk high temperature superconductor above a permanent magnet guideway

Energy Technology Data Exchange (ETDEWEB)

Deng, Z; Wang, J; Zheng, J; Lin, Q; Zhang, Y; Wang, S [Applied Superconductivity Laboratory, Southwest Jiaotong University, Chengdu, 610031 (China)], E-mail: asclab@asclab.cn

2009-05-15

In order to improve the performance of the present high temperature superconducting (HTS) maglev vehicle system, the maglev performance of single- and double-layer bulk high temperature superconductors (HTSC) was investigated above a permanent magnet guideway (PMG). It is found that the maglev performance of a double-layer bulk HTSC is not a simple addition of each layer's levitation and guidance force. Moreover, the applied magnetic field at the position of the upper layer bulk HTSC is not completely shielded by the lower layer bulk HTSC either. 53.5% of the levitation force and 27.5% of the guidance force of the upper layer bulk HTSC are excited in the double-layer bulk HTSC arrangement in the applied field-cooling condition and working gap, bringing a corresponding improvement of 16.9% and 8.8% to the conventional single-layer bulk HTSC. The present research implies that the cost performance of upper layer bulk HTSC is a little low for the whole HTS maglev system.

Enhancement of mechanical properties of 123 superconductors

Science.gov (United States)

Balachandran, Uthamalingam

1995-01-01

A composition and method of preparing YBa.sub.2 Cu.sub.3 O.sub.7-x superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T.sub.c. About 5-20% additions give rise to substantially improved mechanical properties.

Growth and characterization of bulk superconductor material

CERN Document Server

Chen, Dapeng; Maljuk, Andrey; Zhou, Fang

2016-01-01

This book focuses on recently developed crystal growth techniques to grow large and high quality superconducting single crystals. The techniques applied are traveling solvent floating zone (TSFZ) with infrared image furnace, Bridgeman, solution/flux and top seeded solution growth (TSSG) methods. The materials range from cuprates, cobaltates to pnictides including La2CuO4-based (LCO), YBa2Cu3O7-d (YBCO), Bi2Sr2Can−1CunO2n+4+δ (n=1,2,3) (BSCCO) to NaxCoO2. The modified Bridgman “cold finger” method is devoted to the pnictide system with the best quality (transition width DTc~0.5 K) with highest Tc~38.5 K of Ba0.68K0.32Fe2A2. The book presents various iron-based superconductors with different structures, such as 1111, 122, 111, 11 and 42622,10-3-8. Detailed single crystal growth methods (fluxes, Bridgman, floating zone), the associated procedures and their impact to crystal size and quality are presented. The book also describes the influence of doping on the structure and the electric, magnetic, and supe...

Enhancement of mechanical properties of 123 superconductors

Science.gov (United States)

Balachandran, U.

1995-04-25

A composition and method are disclosed of preparing YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T{sub c}. About 5-20% additions give rise to substantially improved mechanical properties.

The effect of Sm addition on the microstructure and superconducting properties of YBCO bulk superconductors

Czech Academy of Sciences Publication Activity Database

Volochová, D.; Diko, P.; Piovarči, S.; Antal, V.; Kováč, J.; Jirsa, Miloš

2017-01-01

Roč. 131, č. 4 (2017), s. 1009-1011 ISSN 0587-4246 Institutional support: RVO:68378271 Keywords : YBaCuO * bulk superconductors * paramagnetic ions * microstructure * vortex pinning Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 0.469, year: 2016

Gap-related trapped magnetic flux dependence between single and combined bulk superconductors

International Nuclear Information System (INIS)

Deng, Z.; Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Uetake, T.; Izumi, M.

2011-01-01

Highlights: → Rectangular YBCO bulks to realize a compact combination. → The gap effect was added to consider in the trapped flux density mapping. → The trapped-flux dependence between single and combined bulks is gap related. → It is possible to estimate the total magnetic flux of bulk combinations. - Abstract: Aiming at examining the trapped-flux dependence between single and combined bulk superconductors for field-pole applications, three rectangular Y 1.65 Ba 2 Cu 3 O 7-x (YBCO) bulks with a possibly compact combination were employed to investigate the trapped-flux characteristics of single and combined bulks with a field-cooling magnetization (FCM) method. A gap-related dependence was found between them. At lower gaps of 1 mm and 5 mm, the peak trapped fields and total magnetic flux of combined bulks are both smaller than the additive values of each single bulk, which can be ascribed to the demagnetization influences of the field around the bulk generated by the adjacent ones. While, at larger gaps like 10 mm, the situation becomes reversed. The combined bulks can attain bigger peak trapped fields as well as total magnetic flux, which indicates that the magnetic field by the bulk combination can reach higher gaps, thanks to the bigger magnetic energy compared with the single bulk. The presented results show that, on one hand, it is possible to estimate the total trapped magnetic flux of combined bulks by an approximate additive method of each single bulk while considering a demagnetization factor; on the other hand, it also means that the performance of combined bulks will be superior to the addition of each single bulk at larger gaps, thus preferable for large-scaled magnet applications.

Gap-related trapped magnetic flux dependence between single and combined bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Deng, Z., E-mail: zgdeng@gmail.co [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan); Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Uetake, T.; Izumi, M. [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan)

2011-05-15

Highlights: {yields} Rectangular YBCO bulks to realize a compact combination. {yields} The gap effect was added to consider in the trapped flux density mapping. {yields} The trapped-flux dependence between single and combined bulks is gap related. {yields} It is possible to estimate the total magnetic flux of bulk combinations. - Abstract: Aiming at examining the trapped-flux dependence between single and combined bulk superconductors for field-pole applications, three rectangular Y{sub 1.65}Ba{sub 2}Cu{sub 3}O{sub 7-x} (YBCO) bulks with a possibly compact combination were employed to investigate the trapped-flux characteristics of single and combined bulks with a field-cooling magnetization (FCM) method. A gap-related dependence was found between them. At lower gaps of 1 mm and 5 mm, the peak trapped fields and total magnetic flux of combined bulks are both smaller than the additive values of each single bulk, which can be ascribed to the demagnetization influences of the field around the bulk generated by the adjacent ones. While, at larger gaps like 10 mm, the situation becomes reversed. The combined bulks can attain bigger peak trapped fields as well as total magnetic flux, which indicates that the magnetic field by the bulk combination can reach higher gaps, thanks to the bigger magnetic energy compared with the single bulk. The presented results show that, on one hand, it is possible to estimate the total trapped magnetic flux of combined bulks by an approximate additive method of each single bulk while considering a demagnetization factor; on the other hand, it also means that the performance of combined bulks will be superior to the addition of each single bulk at larger gaps, thus preferable for large-scaled magnet applications.

Effect of light rare earth doping in 123 high temperature supercoductors

Directory of Open Access Journals (Sweden)

M. Mirzadeh

2006-09-01

Full Text Available   We have studied the structural and electrical properties of Gd(Ba2-xLaxCu3O7+δ [Gd(BaLa123], Gd(Ba2-xNdxCu3O7+δ [Gd(BaNd123], and Nd(Ba2-xPrxCu3O7+δ [Nd(BaPr123] compounds with 0.0≤x≤0.8 prepared by the standard solid-state reaction. The XRD patterns show that all of the samples with x≤0.5 are isosructure 123 phase, but in Gd(BaNd123 and Nd(BaPr123 there are several impurity peaks in the XRD patterns for x≥0.6. We estimated the xcsolubility=1.1, 0.6 and 0.55 in Gd(BaLa123, Nd(BaPr123, and Gd(BaNd123, respectively. The resistivity increases with the increase of doping. The decrease of Tc with the increase of Pr doping is faster than Nd and La doping. The normal-state resistivity is fitted for two and three dimensional variable range hopping (2D&amp3D-VRH and Coulomb gap (CG regimes, separately. Our results indicate that the dominant mechanism for x≥xcSIT is 3D-VRH. The broadening of magnetoresistance have been investigated by TAFC and AH models. The pinning energy and Josephson coupling energy, decrease with the increase of applied magnetic field as U~H-β, these values also decrease with doping concentration Pr is more effective than Nd and La.

Feasibility of introducing ferromagnetic materials to onboard bulk high-T{sub c} superconductors to enhance the performance of present maglev systems

Energy Technology Data Exchange (ETDEWEB)

Deng, Zigang, E-mail: zgdeng@gmail.com [Applied Superconductivity Laboratory (ASCLab), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China); State Key Laboratory of Traction Power (TPL), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China); Wang, Jiasu [Applied Superconductivity Laboratory (ASCLab), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China); Zheng, Jun; Zhang, Ya [Applied Superconductivity Laboratory (ASCLab), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China); State Key Laboratory of Traction Power (TPL), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China); Wang, Suyu [Applied Superconductivity Laboratory (ASCLab), Southwest Jiaotong University (SWJTU), Chengdu, Sichuan 610031 (China)

2013-02-14

Highlights: ► Ferromagnetic materials guide the flux distribution of the PMG to bulk positions. ► With ferromagnetic materials, guidance performance can be enhanced greatly. ► A new HTS Maglev system with onboard ferromagnetic materials is designed. ► The design can meet large guidance force requirements for practical applications. -- Abstract: Performance improvement is a long-term research task for the promotion of practical application of promising high-temperature superconducting (HTS) magnetic levitation (maglev) vehicle technologies. We studied the feasibility to enhance the performance of present HTS Maglev systems by introducing ferromagnetic materials to onboard bulk superconductors. The principle here is to make use of the high magnetic permeability of ferromagnetic materials to alter the flux distribution of the permanent magnet guideway for the enhancement of magnetic field density at the position of the bulk superconductors. Ferromagnetic iron plates were added to the upper surface of bulk superconductors and their geometric and positioning effects on the maglev performance were investigated experimentally. Results show that the guidance performance (stability) was enhanced greatly for a particular setup when compared to the present maglev system which is helpful in the application where large guidance forces are needed such as maglev tracks with high degrees of curves.

Effect of rare-earth ion size on local electron structure in RBa2Cu3O7-δ (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors: A positron study

International Nuclear Information System (INIS)

Chen Zhenping; Zhang Jincang; Su Yuling; Xue Yuncai; Cao Shixun

2006-01-01

The effects of rare-earth ionic size on the local electron structure, lattice parameters and superconductivity have been investigated by positron annihilation technique (PAT) and related experiments for RBa 2 Cu 3 O 7-δ (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors. The local electron density n e is evaluated as a function of the rare-earth radius. The results show that both the bulk-lifetime τ B and the defect lifetime τ 2 increase with increasing rare-earth ionic radius, while the local electron density n e decrease with increasing rare-earth ionic radius. These results prove that the changes of n e , the degree of orthorhombic distortion and the coupling between the Cu-O chains and the CuO 2 planes all have an effect on the superconductivity of RBa 2 Cu 3 O 7-δ systems

Influence of grain boundary connectivity on the trapped magnetic flux of multi-seeded bulk superconductors

Science.gov (United States)

Deng, Z.; Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Hara, S.; Uetake, T.; Izumi, M.

2011-09-01

The top-seeded melt-growth process with multi-seeding technique provides a promising way to fabricate large-sized bulk superconductors in an economical way. To understand the essential characteristics of the multi-seeded bulks, the paper reports the influence of the grain boundary (GB) coupling or connectivity on the total trapped magnetic flux. The coupling ratio, the lowest trapped flux density in the GB area to the averaged top value of the two neighboring peak trapped fields, is introduced to reflect the coupling quality of GBs inside a multi-seeded bulk. By the trapped flux density measurement of four different performance multi-seeded YBCO bulk samples as representatives, it was found that the GB coupling plays an important role for the improvement of the total trapped magnetic flux; moreover, somewhat more significant than the widely used parameter of the peak trapped fields to evaluate the physical performance of bulk samples. This characteristic is different with the case of the well-grown single-grain bulks.

Acoustic emission behavior under bending deformation of YBCO bulk superconductor

International Nuclear Information System (INIS)

Yoneda, K.; Ye, J.; Tomita, M.

2005-01-01

Bending tests were conducted on U-notched specimens cut from a YBCO bulk superconductor. Acoustic emission (AE) signals obtained under loading parallel or perpendicular to the c-axis were analyzed to investigate the correlation between crack growth behavior and the AE signals. As a result of analyzing log-log plots of strength (σ B ) versus total AE energy (ΣE AE ), a linear relationship was found between ΣE AE and σ B n . Cracks could be broadly divided into two types based on the value of n as an index of crack growth behavior. One type consisted of microcracks originating from cleavage planes and gas holes; these crack propagated parallel to the c-axis and had an n index value of approximately 0.7. The other type was a main crack that originated from the U-notch and had an n index value of approximately 6.5. A sample (A) loaded parallel to the c-axis showed mean bending strength of 74.8MPa. Cracks displaying two different growth patterns of n=0.7 and 6.5 were presented in this sample. Microcracks parallel to the c-axis occurred in the vicinity of 5-10MPa. This sample was characterized by mixed crack growth of a main crack and microcracks. A sample (B) loaded perpendicular to the c-axis displayed mean bending strength of 43MPa. A main crack occurred in the vicinity of 20MPa and displayed a single growth pattern of n=6.5. By analyzing AE signals in this way in the process of conducting a strength evaluation, it was possible to evaluate the failure process of the bulk superconductor in relation to the strength level induced by the applied load

Correlation between structural, electrical and magnetic properties of GdMnO{sub 3} bulk ceramics

Energy Technology Data Exchange (ETDEWEB)

Samantaray, S. [Institute of Materials Science, Planetarium Building, Bhubaneswar 751013, Odisha (India); Mishra, D.K. [Department of Physics, Institute of Technical Education and Research, S ‘O’ A University, Bhubaneswar 751030, Odisha (India); Pradhan, S.K. [Institute of Materials Science, Planetarium Building, Bhubaneswar 751013, Odisha (India); Mishra, P.; Sekhar, B.R. [Institue of Physics, Sachivalaya Marg, Bhubaneswar, Odisha (India); Behera, Debdhyan [Advanced Materials Technology Department, CSIR-Institute of Minerals and Materials Technology, Bhubaneswar 751013, Odisha (India); Rout, P.P.; Das, S.K. [Institute of Materials Science, Planetarium Building, Bhubaneswar 751013, Odisha (India); Sahu, D.R. [School of Physics, University of the Witwatersrand, Johannesburg (South Africa); Roul, B.K., E-mail: ims@iopb.res.in [Institute of Materials Science, Planetarium Building, Bhubaneswar 751013, Odisha (India)

2013-08-15

This paper reports the effect of sintering temperature on ferroelectric properties of GdMnO{sub 3} (GMO) bulk ceramics at room temperature prepared by the conventional solid state reaction route following slow step sintering schedule. Ferroelectric hysteresis loop as well as sharp dielectric anomaly in pure (99.999%) GMO sintered ceramics has been clearly observed. Samples sintered at 1350 °C become orthorhombic with Pbnm space group and showed frequency independent sharp dielectric anomalies at 373 K and a square type of novel ferroelectric hysteresis loop was observed at room temperature. Interestingly, dielectric anomalies and ferroelectric behavior were observed to be dependent upon sintering temperature of GdMnO{sub 3}. Room temperature dielectric constant (ε{sub r}) value at different frequencies is observed to be abnormally high. The magnetic field and temperature dependent magnetization show antiferromagnetic behavior at 40 K for both 1350 °C and 1700 °C sintered GMO. Present findings showed the possibility of application of GdMnO{sub 3} at room temperature as multifunctional materials. - Highlights: • Preparation of single-phasic polycrystalline GdMnO{sub 3} sample by the solid state sintering route. • Observation of square type P–E hysteresis loop with higher saturation and remnant polarization. • Observation of antiferromagnetic behavior at 40 K in polycrystalline GdMnO{sub 3}. • Possibility of room temperature application of GdMnO{sub 3} as multifunctional material.

Bulk and nanocrystalline electron doped Gd0.15Ca0.85MnO3: Synthesis and magnetic characterization

Science.gov (United States)

Dhal, Lakshman; Chattarpal; Nirmala, R.; Santhosh, P. N.; Kumary, T. Geetha; Nigam, A. K.

2014-09-01

Polycrystalline Gd0.15Ca0.85MnO3 sample was prepared by solid state reaction method and nanocrystalline samples of different grain sizes of the same were prepared by sol-gel method. Phase purity and composition were verified by room temperature X-ray diffraction and SEM-EDAX analysis. Magnetization data of bulk Gd0.15Ca0.85MnO3 in 5 kOe field shows a peak at 119 K (TN) suggesting an antiferromagnetic transition. Nanocrystalline Gd0.15Ca0.85MnO3 sample ( 54 nm size) also shows a cusp at 107 K and a broad thermal hysteresis between field cooled cooling (FCC) and field cooled warming (FCW) data around this temperature. This thermal hysteresis suggests possible crystal structural transition. Field variation of magnetization of bulk Gd0.15Ca0.85MnO3 at 5 K shows a tendency to saturate, but yields a magnetic moment value of only 1.12 μB/f.u. in 70 kOe. The value of magnetization of nanocrystalline sample at 5 K in 70 kOe field is slightly larger and is 1.38 μB/f.u. which is probably due to the surface moments of the nanoparticle samples. Both the samples show Curie-Weiss-like behaviour in their paramagnetic state.

Temperature dependence of the mechanical properties of melt-processed Dy-Ba-Cu-O bulk superconductors evaluated by three point bending tests

International Nuclear Information System (INIS)

Katagiri, K; Nyilas, A; Sato, T; Hatakeyama, Y; Hokari, T; Teshima, H; Iwamoto, A; Mito, T

2006-01-01

Dy-Ba-Cu-O bulk superconductor has an excellent capability of trapping magnetic flux and lower heat conductivity at cryogenic temperatures as compared with Y-Ba-Cu-O bulk superconductor. The Young's modulus and the bending strength in the range from room temperature to 7 K were measured by the three-point bending tests using specimens cut from a melt-processed Dy-Ba-Cu-O bulk superconductor. They were tested in a helium gas flow type cryostat at Forschungszentrum Karlsruhe and in a liquid nitrogen bath at Iwate University. The Young's modulus was calculated by either the slope of stress-strain curve or that of the load-deflection curve of the specimen. Although the bending strength measured in the two institutes coincided well, there was a significant discrepancy in the Young's modulus. The Young's modulus and bending strength increased with decrease of temperature down to 7 K. The amount of increase in the Young's modulus and the bending strength were about 32% and 36% of those at room temperature, respectively. The scatter of data for each run was significant and did not depend on temperature. The temperature dependence of the Young's modulus coincided with that in Y-Ba-Cu-O obtained by ultrasonic velocity. The temperature dependence of the Young's modulus and the bending strength was discussed from the view point of interatomic distance of the bulk crystal

Shape-forming and densification of ceramic superconductors

International Nuclear Information System (INIS)

Prakash, Om; Thomas, C.A.; Magadum, A.P.; Anklekar, R.M.; Khosla, N.K.; Kumar, Sunil; Chaudhuri, B.; Ramesh, M.; Rao, B.T.; Rama Mohan, T.R.

1991-01-01

Processing studies on varied shape-forming and densification of bulk ceramic superconductor, YBa 2 Cu 3 Osub(7-δ), are reported in this paper. Polyvinyl butyral-polyethylene glycol-trichloroethylene has been found to be the best binder-plasticizer-solvent system in plastic shape-forming. The effect of initial particle morphology on final densification has been the most sensitive single parameter as compared to compaction pressure and final sintering durations at ∼930degC. 1-2-3 powders of mean particle size ∼1.94μm have yielded sintered densities ∼92%T.D. albeit with lower oxygen intake Osub(6.7). (author). 8 refs., 8 figs

Influence of grain boundary connectivity on the trapped magnetic flux of multi-seeded bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Deng, Z., E-mail: zgdeng@gmail.com [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan); Miki, M.; Felder, B.; Tsuzuki, K.; Shinohara, N.; Hara, S.; Uetake, T.; Izumi, M. [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, Tokyo 135-8533 (Japan)

2011-09-15

Four different performance multi-seeded YBCO bulks as representatives. A coupling ratio to reflect the coupling quality of GBs inside multi-seeded bulks. An averaged trapped magnetic flux density parameter was introduced. The top-seeded melt-growth process with multi-seeding technique provides a promising way to fabricate large-sized bulk superconductors in an economical way. To understand the essential characteristics of the multi-seeded bulks, the paper reports the influence of the grain boundary (GB) coupling or connectivity on the total trapped magnetic flux. The coupling ratio, the lowest trapped flux density in the GB area to the averaged top value of the two neighboring peak trapped fields, is introduced to reflect the coupling quality of GBs inside a multi-seeded bulk. By the trapped flux density measurement of four different performance multi-seeded YBCO bulk samples as representatives, it was found that the GB coupling plays an important role for the improvement of the total trapped magnetic flux; moreover, somewhat more significant than the widely used parameter of the peak trapped fields to evaluate the physical performance of bulk samples. This characteristic is different with the case of the well-grown single-grain bulks.

Fracture toughness for copper oxide superconductors

Science.gov (United States)

Goretta, Kenneth C.; Kullberg, Marc L.

1993-01-01

An oxide-based strengthening and toughening agent, such as tetragonal Zro.sub.2 particles, has been added to copper oxide superconductors, such as superconducting YBa.sub.2 Cu.sub.3 O.sub.x (123) to improve its fracture toughness (K.sub.IC). A sol-gel coating which is non-reactive with the superconductor, such as Y.sub.2 BaCuO.sub.5 (211) on the ZrO.sub.2 particles minimized the deleterious reactions between the superconductor and the toughening agent dispersed therethrough. Addition of 20 mole percent ZrO.sub.2 coated with 211 yielded a 123 composite with a K.sub.IC of 4.5 MPa(m).sup.0.5.

Fracture toughness for copper oxide superconductors

Science.gov (United States)

Goretta, K.C.; Kullberg, M.L.

1993-04-13

An oxide-based strengthening and toughening agent, such as tetragonal ZrO[sub 2] particles, has been added to copper oxide superconductors, such as superconducting YBa[sub 2]Cu[sub 3]O[sub x] (123) to improve its fracture toughness (K[sub IC]). A sol-gel coating which is non-reactive with the superconductor, such as Y[sub 2]BaCuO[sub 5] (211) on the ZrO[sub 2] particles minimized the deleterious reactions between the superconductor and the toughening agent dispersed therethrough. Addition of 20 mole percent ZrO[sub 2] coated with 211 yielded a 123 composite with a K[sub IC] of 4.5 MPa(m)[sup 0.5].

Gd-substituted Bi-2223 superconductor

Indian Academy of Sciences (India)

The effects of gadolinium doping at calcium site on the normal and super- conducting properties of Bi-2223 system were ... quantities of the metal oxides and the carbonates were taken and thoroughly mixed. The calcination of the mixture after .... Therefore, Gd has higher solubility in (BiPb)-2223 as compared to Pr, and is, ...

Influence of Sm2O3 microalloying and Yb contamination on Y211 particles coarsening and superconducting properties of IG YBCO bulk superconductors

Science.gov (United States)

Vojtkova, L.; Diko, P.; Kovac, J.; Vojtko, M.

2018-06-01

Single grain YBa2Cu3O7‑x (YBCO or Y123) bulk superconductors were produced by an infiltration growth process. The solid phase precursor was prepared by solid state synthesis from Y2O3 + BaCuO2 powders. The influence of the addition of Sm2O3 and YB contamination from the substrate on the microstructure and superconducting properties was analyzed. The dependences of Yb concentration on the distance from the bottom of the samples measured by energy dispersive spectroscopy microanalysis used in conjunction with scanning electron microscopy confirmed the contamination of the samples during the melting stage of the sample preparation. It is shown that the addition of Sm in low concentration and its combination with Yb from the substrate modify the coarsening of the Y211 particles as well as lead to the appearance of a secondary peak effect in the field dependences of the critical current density.

Materials process and applications of single grain (RE)-Ba-Cu-O bulk high-temperature superconductors

Energy Technology Data Exchange (ETDEWEB)

Li Beizhan; Zhou Difan; Xu Kun; Hara, Shogo; Tsuzuki, Keita; Miki, Motohiro; Felder, Brice; Deng Zigang [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology (TUMSAT), 2-1-6, Etchu-jima, Koto-ku, Tokyo 135-8533 (Japan); Izumi, Mitsuru, E-mail: izumi@kaiyodai.ac.jp [Laboratory of Applied Physics, Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology (TUMSAT), 2-1-6, Etchu-jima, Koto-ku, Tokyo 135-8533 (Japan)

2012-11-20

This paper reviews recent advances in the melt process of (RE)-Ba-Cu-O [(RE)BCO, where RE represents a rare earth element] single grain high-temperature superconductors (HTSs), bulks and its applications. The efforts on the improvement of the magnetic flux pinning with employing the top-seeded melt-growth process technique and using a seeded infiltration and growth process are discussed. Which including various chemical doping strategies and controlled pushing effect based on the peritectic reaction of (RE)BCO. The typical experiment results, such as the largest single domain bulk, the clear TEM observations and the significant critical current density, are summarized together with the magnetization techniques. Finally, we highlight the recent prominent progress of HTS bulk applications, including Maglev, flywheel, power device, magnetic drug delivery system and magnetic resonance devices.

Materials process and applications of single grain (RE)-Ba-Cu-O bulk high-temperature superconductors

Science.gov (United States)

Li, Beizhan; Zhou, Difan; Xu, Kun; Hara, Shogo; Tsuzuki, Keita; Miki, Motohiro; Felder, Brice; Deng, Zigang; Izumi, Mitsuru

2012-11-01

This paper reviews recent advances in the melt process of (RE)-Ba-Cu-O [(RE)BCO, where RE represents a rare earth element] single grain high-temperature superconductors (HTSs), bulks and its applications. The efforts on the improvement of the magnetic flux pinning with employing the top-seeded melt-growth process technique and using a seeded infiltration and growth process are discussed. Which including various chemical doping strategies and controlled pushing effect based on the peritectic reaction of (RE)BCO. The typical experiment results, such as the largest single domain bulk, the clear TEM observations and the significant critical current density, are summarized together with the magnetization techniques. Finally, we highlight the recent prominent progress of HTS bulk applications, including Maglev, flywheel, power device, magnetic drug delivery system and magnetic resonance devices.

Fault current limiter using bulk oxides superconductors

International Nuclear Information System (INIS)

Belmont, O.; Ferracci, P.; Porcar, L.; Barbut, J.M.; Tixador, P.; Noudem, J.G.; Bourgault, D.; Tournier, R.

1998-01-01

We study the limitation possibilities of bulk Bi high T c materials. For this we test these materials with AC or DC currents above their critical currents. We study particularly the evolution of the voltage with time or with current. The material, the value of the current and the time duration play important parts. For sintered Bi samples the voltage depends only on the current even for values much larger than the critical current. With textured samples the V(I) curves shows an hysteretic behaviour due to a warming up. The textured materials are more interesting than sintered ones in terms of required volume for the current limitation. In both cases the superconductors are in a dissipative state but not in the normal state. This state is nevertheless reached if the dissipated energy inside the sample is sufficient. We have tried to apply a magnetic field on the samples in order to trigger a more effective limitation. The voltage increases but with a limited effect for currents much higher (3-4 times) than the critical zero field current. We think that the dissipative state is due mainly to the grain boundaries which become resistive above the critical current. (orig.)

Levitation properties of superconducting magnetic bearings using superconducting coils and bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Arai, Yuuki; Seino, Hiroshi; Nagashima, Ken [Railway Technical Research Institute, 2-8-38 Hikari-cho, Kokubunji-shi, Tokyo 185-8540 (Japan)

2010-11-15

We have been developing a flywheel energy storage system (FESS) with 36 MJ energy capacity for a railway system with superconducting magnetic bearings (SMBs). We prepared two kinds of models using superconducting coils and bulk superconductors (SCs). One model demonstrated SMB load capacity of 20 kN and the other model proved non-contact stable levitation and non-contact rotation with SMBs. Combining these results, the feasibility of a 36 MJ energy capacity FESS with SMBs completely inside a cryostat has been confirmed. In this paper, we report the levitation properties of SMBs in these models.

Levitation properties of superconducting magnetic bearings using superconducting coils and bulk superconductors

International Nuclear Information System (INIS)

Arai, Yuuki; Seino, Hiroshi; Nagashima, Ken

2010-01-01

We have been developing a flywheel energy storage system (FESS) with 36 MJ energy capacity for a railway system with superconducting magnetic bearings (SMBs). We prepared two kinds of models using superconducting coils and bulk superconductors (SCs). One model demonstrated SMB load capacity of 20 kN and the other model proved non-contact stable levitation and non-contact rotation with SMBs. Combining these results, the feasibility of a 36 MJ energy capacity FESS with SMBs completely inside a cryostat has been confirmed. In this paper, we report the levitation properties of SMBs in these models.

Single pulsed-field magnetization on Gd-Ba-Cu-O Bulk HTS assembled for axial-gap type rotating machines

International Nuclear Information System (INIS)

Morita, E; Matsuzaki, H; Kimura, Y; Ohtani, I; Izumi, M; Nonaka, Y; Murakami, M; Ida, T; Sugimoto, H; Miki, M; Kitano, M

2006-01-01

We employed Gd-bulk HTS magnets as rotating poles for a smaller and lighter axial-gap type rotating machine. The bulk was placed between two vortex-type armature coils and cooled down to 77 K under zero-field. Pulsed current was applied to the vortex-type magnetizing coils. The trapped field distribution and transient flux behaviour strongly depend on the radial dimension of the armature vortex-type coil. In the present study, we show that there is an optimal radial dimension of magnetizing coils to the given bulk disk size to give a homogeneously conical distribution of the trapped flux

Measurement of the magnetic field inside the holes of a drilled bulk high-Tc superconductor

Science.gov (United States)

Lousberg, Gregory P.; Fagnard, Jean-François; Noudem, Jacques G.; Ausloos, Marcel; Vanderheyden, Benoit; Vanderbemden, Philippe

2009-04-01

We use macroscopic holes drilled in a bulk YBCO superconductor to probe its magnetic properties in the volume of the sample. The sample is subjected to an AC magnetic flux with a density ranging from 30 to 130 mT and the flux in the superconductor is probed by miniature coils inserted in the holes. In a given hole, three different penetration regimes can be observed: (i) the shielded regime, where no magnetic flux threads the hole; (ii) the gradual penetration regime, where the waveform of the magnetic field has a clipped sine shape whose fundamental component scales with the applied field; and (iii) the flux concentration regime, where the waveform of the magnetic field is nearly a sine wave, with an amplitude exceeding that of the applied field by up to a factor of two. The distribution of the penetration regimes in the holes is compared with that of the magnetic flux density at the top and bottom surfaces of the sample, and is interpreted with the help of optical polarized light micrographs of these surfaces. We show that the measurement of the magnetic field inside the holes can be used as a local characterization of the bulk magnetic properties of the sample.

Enhanced glass forming ability and refrigerant capacity of a Gd55Ni22Mn3Al20 bulk metallic glass

International Nuclear Information System (INIS)

Xia, L.; Chan, K.C.; Tang, M.B.

2011-01-01

Highlights: → A new Gd 55 Ni 22 Mn 3 Al 20 bulk metallic glass (BMG) was synthesized by minor Mn addition. → The BMG has enhanced glass forming ability and excellent refrigerant capacity (RC). → The RC of the BMG reaches a high value of 825 J kg -1 under a field of 3979 kA/m. → Its excellent RC is related to its large effective magnetic moment. - Abstract: In this work, a small amount of Mn was added to a Gd 55 Ni 25 Al 20 glass forming alloy, as a replacement for Ni, and a Gd 55 Ni 22 Mn 3 Al 20 bulk metallic glass (BMG) was obtained by suction casting. Its glass forming ability (GFA) was characterized by X-ray diffraction and differential scanning calorimetry, and its magnetic properties were measured using a magnetic property measurement system. It is found that the minor Mn addition can significantly improve both the GFA and the magnetocaloric effect (MCE) of the alloy. The refrigerant capacity (RC) of the BMG can reach a high value of 825 J kg -1 under a field of 3979 kA/m, which is about 29% larger than that of a Gd 55 Ni 25 Al 20 BMG. The effect of the minor Mn addition on the GFA and MCE of the BMG was investigated in the study.

Improving magnetic properties of MgB_2 bulk superconductors by synthetic engine oil treatment

International Nuclear Information System (INIS)

Taylan Koparan, E.; Savaskan, B.; Yanmaz, E.

2016-01-01

Highlights: • The effects of synthetic engine oil treatment on magnetic properties of bulk MgB_2 superconductors has been first time investigated and reported. • Synthetic engine oil used as a product which is cheap and a rich carbon source obviously has improved the superconducting magnetic properties of MgB_2. • The critical current density of all of MgB_2 samples immersed at different standby time in engine oil in whole field range has been better than that of the pure MgB_2 sample. • The MgB_2 sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. - Abstract: The present study focuses on the effects of standby time of the MgB_2 samples immersed in synthetic engine oil on the critical current density ( J_c(H)), magnetic field dependence of the pinning force density f_p(b) and T_c performances of MgB_2 bulk superconductors. Synthetic engine oil was used as a product which is cheap and a rich carbon source. Manufactured MgB_2 pellet samples were immersed at different standby time of 30 min, 120 min, 300 min and 1440 min in synthetic engine oil after the first heating process. Finally, MgB_2 samples immersed in synthetic engine oil were sintered at 1000 °C and kept for 15 min in Ar atmosphere. The critical current density of all of MgB_2 samples immersed at different standby time in engine oil in whole field range was better than that of the pure MgB_2 sample because of the number of the pinning centers. The MgB_2 sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. The J_c value for the pure sample is 2.0 × 10"3 A/cm"2, whereas for the MgB_2 sample immersed at 300 min standby time in engine oil the J_c is enhanced to 4.8 × 10"3 A/cm"2 at 5 K and 3 T. The superconducting transition temperature (T_c) did not change with the increasing standby time of the samples in synthetic engine oil at all. The best diamagnetic property was

A Double-Decker Levitation Experiment Using a Sandwich of Superconductors.

Science.gov (United States)

Jacob, Anthony T.; And Others

1988-01-01

Shows that the mutual repulsion that enables a superconductor to levitate a magnet and a magnet to levitate a superconductor can be combined into a single demonstration. Uses an overhead projector, two pellets of "1-2-3" superconductor, Nd-Fe-B magnets, liquid nitrogen, and paraffin. Offers superconductor preparation, hazards, and disposal…

Magnetic torque transferring study for bulk High-Tc superconductors and permanent magnets

International Nuclear Information System (INIS)

Wongsatanawarid, A; Suzuki, A; Seki, H; Murakami, M

2009-01-01

The torque transferring mechanism taking place in a superconducting mixer design has been studied. Several coupling magnetic arrangements were investigated for more details in the engineering design. A bulk superconductor sample was used to study the torque forces for various cooling gaps, and the twist angle dependence was also monitored for the rotational stiffness in stability. The experimental data with four permanent magnet configurations have been studied in the present work. The maximum torque forces are summarized for usage of engineering design with various gaps. The torque/gap characteristics for four configurations were also measured for the optimisation of the torque at a designed operating gap.

Processing yttrium-barium-copper oxide superconductor zero gravity using a double float zone surface

International Nuclear Information System (INIS)

Pettit, D.R.; Peterson, D.E.; Kubat-Martin, K.A.; Petrovic, J.J.; Sheinberg, H.; Coulter, Y.; Day, D.E.

1997-04-01

The effects of processing YBa 2 Cu 3 O x (Y123) superconductor in the near-zero gravity (0g) environment provided by the NASA KC-135 airplane flying on parabolic trajectories were studied. A new sheet float zone furnace, designed for this study, enabled fast temperature ramps. Up to an 18-gram sample was processed with each parabola. Samples of Y123 were processed as bulk sheets, composites containing Ag and Pd, and films deposited on single crystal Si and MgO substrates. The 0g-processed samples were multi-phase yet retained a localized Y123 stoichiometry where a single ground-based (1g) oxygen anneal at temperatures of 800 C recovered nearly 100-volume percent superconducting Y123. The 1g processed control samples remained multi-phase after the same ground-based anneal with less than 45 volume percent as superconducting Y123. The superconducting transition temperature was 91 K for both 0g and 1g processed samples. A 29 wt.% Ag/Y123 composite had a transition temperature of 93 K. Melt texturing of bulk Y123 in 0g produced aligned grains about a factor of three larger than in analogous 1g samples. Transport critical current densities were at or below 18 A/cm 2 , due to the formation of cracks caused by the rapid heating rates required by the short time at 0g. Y123 deposited on single crystal Si and MgO in 0g was 30 vol.% y123 without an anneal. A weak superconducting transition at 80 K on MgO showed that substrate interactions occurred

Air stability and magnetic properties of GdN, TiN, and (Gd,Ti)N nanoparticles

International Nuclear Information System (INIS)

Si Pingzhan; Choi, C. J.; Tegus, O.; Brueck, E.; Geng, D. Y.; Zhang, Z. D.

2008-01-01

GdN, TiN, and (Gd,Ti)N nanoparticles were prepared by arc evaporating Gd, Ti, and Gd-Ti alloys in N 2 , respectively. Most of these nanoparticles show narrow size distribution with average diameter of 20 nm. Shell/core structure was observed in the (Gd,Ti)N nanoparticles, in which the shell was formed by surface reaction with air. (Gd,Ti)N nanoparticles are more stable than GdN nanoparticles in air due partially to the formation of the protective shell. The Curie temperature of GdN nanoparticles is lower than that of the bulk GdN. Both GdN and (Gd, Ti)N nanoparticles are difficult to reach magnetic saturation and show zero coercivity

Growth anisotropy effect of bulk high temperature superconductors on the levitation performance in the applied magnetic field

Science.gov (United States)

Zheng, J.; Liao, X. L.; Jing, H. L.; Deng, Z. G.; Yen, F.; Wang, S. Y.; Wang, J. S.

2013-10-01

Growth anisotropies of bulk high temperature superconductors (HTSCs) fabricated by a top-seeded melt texture growth process, that is, different pinning effect in the growth sectors (GSs) and growth sector boundaries (GSBs), possess effect on the macro flux trapping and levitation performance of bulk HTSCs. Previous work (Physics Procedia, 36 (2012) 1043) has found that the bulk HTSC array with aligned GSB pattern (AGSBP) exhibits better capability for levitation and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP). In this paper, we further examine this growth anisotropy effect on the maglev performance of a double-layer bulk HTSC. In contrast to reported trapped flux cases (Supercond. Sci. Technol. 19 (2006) S466), the two superposed bulk HTSCs with same AGSBP with PMG are found to show better maglev performance. These series of results are helpful and support a new way for the performance optimization of present HTS maglev systems.

High critical currents in heavily doped (Gd,Y)Ba2Cu3Ox superconductor tapes

Energy Technology Data Exchange (ETDEWEB)

Selvamanickam, V; Gharahcheshmeh, MH; Xu, A; Galstyan, E; Delgado, L; Cantoni, C

2015-01-19

REBa2Cu3Ox ((REBCO), RE = rare earth) superconductor tapes with moderate levels of dopants have been optimized for high critical current density in low magnetic fields at 77 K, but they do not exhibit exemplary performance in conditions of interest for practical applications, i.e., temperatures less than 50K and fields of 2-30 T. Heavy doping of REBCO tapes has been avoided by researchers thus far due to deterioration in properties. Here, we report achievement of critical current densities (J(c)) above 20 MA/cm(2) at 30 K, 3 T in heavily doped (25 mol.% Zr-added) (Gd,Y)Ba2Cu3Ox superconductor tapes, which is more than three times higher than the J(c) typically obtained in moderately doped tapes. Pinning force levels above 1000 GN/m(3) have also been attained at 20 K. A composition map of lift factor in J(c) (ratio of J(c) at 30 K, 3 T to the J(c) at 77 K, 0 T) has been developed which reveals the optimum film composition to obtain lift factors above six, which is thrice the typical value. A highly c-axis aligned BaZrO3 (BZO) nanocolumn defect density of nearly 7 x 10(11) cm(-2) as well as 2-3 nm sized particles rich in Cu and Zr have been found in the high J(c) films. (C) 2015 AIP Publishing LLC.

Magnetic levitation systems using a high-Tc superconducting bulk magnet

Energy Technology Data Exchange (ETDEWEB)

Ohsaki, Hiroyuki [Dept. of Electrical Engineering, Univ. of Tokyo (Japan); Kitahara, Hirotaka [Dept. of Electrical Engineering, Univ. of Tokyo (Japan); Masada, Eisuke [Dept. of Electrical Engineering, Univ. of Tokyo (Japan)

1996-12-31

Recent development of high-performance high-Tc bulk superconductors is making their application for electromagnetic force use feasible. We have studied electromagnetic levitation systems using high-Tc bulk superconducting material. In this paper, after an overview of superconducting magnetic levitation systems, with an emphasis on high-Tc bulk superconductor applications, experimental results of a high-Tc bulk EMS levitation and FEM analysis results of magnetic gradient levitation using bulk superconductor are described. Problems to be solved for their application are also discussed. (orig.)

Microstructural analyses and critical current densities in the high-Tc superconductor system ReBa2Cu3OX, with RE = Y, Sm, Eu, Gd, Dy, Ho

International Nuclear Information System (INIS)

Schindler, G.; Seebacher, B.

1989-01-01

The authors report on investigations into the impact of the rare earths (RE) as given in the title on the ceramic microstructure and the critical current density j c in the superconductor system REBa 2 Cu 3 O x . With RE = Sm, Eu, or Gd, the material is homogeneous in phase and crystallizes in platelets with maximum sizes of up to 350 μm. Material with RE = Y, Dy, or Ho exhibits grain sizes up to 500 μm, and a low amount of phase inhomogeneities. The critical currents measured are between 25 Acm -2 and 290 Acm -2 at 77 K, without external field. The highest values are found in systems with RE = Eu or Gd. (orig.) [de

ZnO doping effects in melt-textured (Nd.sub.0.33./sub. Eu.sub.0.39./sub. Gd.sub.0.27./sub.)Ba.sub.2./sub. Cu.sub.3./sub. O.sub.y./sub. grown from MgO seed

Czech Academy of Sciences Publication Activity Database

Muralidhar, M.; Kono, T.; Jirsa, Miloš; Sakamoto, N.; Murakami, M.; Hirabayashi, I.

2006-01-01

Roč. 19, - (2006), L25-L28 ISSN 0953-2048 Institutional research plan: CEZ:AV0Z10100520 Keywords : crystal growth * MgO seed * ZnO doping * ternary LRE-123 * bulk superconductors Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.440, year: 2006

Influence of crossed fields in structures combining large grain, bulk (RE)BCO superconductors and soft ferromagnetic discs

International Nuclear Information System (INIS)

Philippe, M P; Fagnard, J F; Wéra, L; Vanderheyden, B; Vanderbemden, P; Morita, M; Nariki, S; Teshima, H; Caps, H

2016-01-01

Bulk (RE)BCO superconductors are able to trap record magnetic fields and can be used as powerful permanent magnets in various engineering applications such as rotating machines and magnetic bearings. When such superconducting (SC) “trapped field magnets” are combined to a ferromagnetic (FM) disc, the total magnetic moment is increased with respect to that of the superconductor alone. In the present work, we study experimentally the magnetic behaviour of such hybrid FM/SC structures when they are subjected to cycles of applied field that are orthogonal to their permanent magnetization, i.e. a “crossed-field” configuration. Experimental results show that the usual “crossed-field demagnetization” caused by the cycles of transverse field is strongly reduced in the presence of the ferromagnet. (paper)

Static Properties of Superconductor Journal Bearing Substator for Superconductor Flywheel Energy Storage System

International Nuclear Information System (INIS)

Park, B. J.; Jung, S. Y.; Lee, J. P.; Park, B. C.; Jeong, N. H.; Sung, T. H.; Han, Y. H.

2008-01-01

A Superconductor Flywheel Energy Storage System(SFES) mainly consists of a pair of non-contacting High Temperature Superconductor(HTS) bearings that provide very low frictional losses, a composite flywheel with high energy storage density. The HTS bearings, which offer dynamic stability without active control, are the key technology that distinguishes the SFES from other flywheel energy storage devices, and great effort is being put into developing this technology. The Superconductor Journal Bearing(SJB) mainly consists of HTS bulks and a stator, which holds the HTS bulks and also acts as a cold head. Static properties of HTS bearings provide data to solve problems which may occur easily in a running system. Since stiffness to counter vibration is the main parameter in designing an HTS bearing system, we investigate SJB magnetic force through static properties between the Permanent Magnet(PM) and HTS. We measure stiffness in static condition and the results are used to determine the optimal number of HTS bulks for a 100kWh SFES.

Microgravity Processing of Oxide Superconductors

Science.gov (United States)

Hofmeister, William H.; Bayuzick, Robert J.; Vlasse, Marcus; McCallum, William; Peters, Palmer (Technical Monitor)

2000-01-01

The primary goal is to understand the microstructures which develop under the nonequilibrium solidification conditions achieved by melt processing in copper oxide superconductor systems. More specifically, to define the liquidus at the Y- 1:2:3 composition, the Nd-1:2:3 composition, and several intermediate partial substitution points between pure Y-1:2:3 and Nd-1:2:3. A secondary goal has been to understand resultant solidification morphologies and pathways under a variety of experimental conditions and to use this knowledge to better characterize solidification phenomena in these systems.

Stress analysis in high-temperature superconductors under pulsed field magnetization

Science.gov (United States)

Wu, Haowei; Yong, Huadong; Zhou, Youhe

2018-04-01

Bulk high-temperature superconductors (HTSs) have a high critical current density and can trap a large magnetic field. When bulk superconductors are magnetized by the pulsed field magnetization (PFM) technique, they are also subjected to a large electromagnetic stress, and the resulting thermal stress may cause cracking of the superconductor due to the brittle nature of the sample. In this paper, based on the H-formulation and the law of heat transfer, we can obtain the distributions of electromagnetic field and temperature, which are in qualitative agreement with experiment. After that, based on the dynamic equilibrium equations, the mechanical response of the bulk superconductor is determined. During the PFM process, the change in temperature has a dramatic effect on the radial and hoop stresses, and the maximum radial and hoop stress are 24.2 {{MPa}} and 22.6 {{MPa}}, respectively. The mechanical responses of a superconductor for different cases are also studied, such as the peak value of the applied field and the size of bulk superconductors. Finally, the stresses are also presented for different magnetization methods.

Effect of rare-earth ion size on local electron structure in RBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors: A positron study

Energy Technology Data Exchange (ETDEWEB)

Chen Zhenping [Department of Technology and Physics, Zhengzhou University of Light Industry, 5 Dongfeng Road, Zhengzhou, Henan 450002 (China)]. E-mail: czhping@zzuli.edu.cn; Zhang Jincang [Department of Physics, Shanghai University, Shanghai 200436 (China); Su Yuling [Department of Technology and Physics, Zhengzhou University of Light Industry, 5 Dongfeng Road, Zhengzhou, Henan 450002 (China); Xue Yuncai [Department of Technology and Physics, Zhengzhou University of Light Industry, 5 Dongfeng Road, Zhengzhou, Henan 450002 (China); Cao Shixun [Department of Physics, Shanghai University, Shanghai 200436 (China)

2006-02-15

The effects of rare-earth ionic size on the local electron structure, lattice parameters and superconductivity have been investigated by positron annihilation technique (PAT) and related experiments for RBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (R = Tm, Dy, Gd, Eu, Nd and Y) superconductors. The local electron density n {sub e} is evaluated as a function of the rare-earth radius. The results show that both the bulk-lifetime {tau} {sub B} and the defect lifetime {tau} {sub 2} increase with increasing rare-earth ionic radius, while the local electron density n {sub e} decrease with increasing rare-earth ionic radius. These results prove that the changes of n {sub e}, the degree of orthorhombic distortion and the coupling between the Cu-O chains and the CuO{sub 2} planes all have an effect on the superconductivity of RBa{sub 2}Cu{sub 3}O{sub 7-{delta}} systems.

Anisotropy and intergrain current density in oriented grained bulk YBa2Cu3Ox superconductor

International Nuclear Information System (INIS)

Selvamanickam, V.; Salama, K.

1990-01-01

The intergrain transport current density and its anisotropy have been studied in oriented grained bulk YBa 2 Cu 3 O x superconductors fabricated by the liquid phase processing method. Current density measurements were performed on oriented grained samples with the transport current aligned at different angles to the a-b plane. In these measurements, the transport current passed through several oriented grain boundaries. The results indicate that the critical current density drops rapidly when the transport current flows at small angles to the a-b plane and then decreases slowly at larger angles. At 77 K and zero magnetic field, an anisotropy ratio of about 25 is observed between J c along a-b plane and that perpendicular to the plane. Further, the critical current density in these samples is found to depend weakly on magnetic field even though the current crosses grain boundaries. These results support the notion that grain boundaries of these superconductors are different in nature from those of solid-state sintered samples.

High critical currents in heavily doped (Gd,Y)Ba2Cu3Ox superconductor tapes

International Nuclear Information System (INIS)

Selvamanickam, V.; Gharahcheshmeh, M. Heydari; Xu, A.; Galstyan, E.; Delgado, L.; Cantoni, C.

2015-01-01

REBa 2 Cu 3 O x ((REBCO), RE = rare earth) superconductor tapes with moderate levels of dopants have been optimized for high critical current density in low magnetic fields at 77 K, but they do not exhibit exemplary performance in conditions of interest for practical applications, i.e., temperatures less than 50 K and fields of 2–30 T. Heavy doping of REBCO tapes has been avoided by researchers thus far due to deterioration in properties. Here, we report achievement of critical current densities (J c ) above 20 MA/cm 2 at 30 K, 3 T in heavily doped (25 mol. % Zr-added) (Gd,Y)Ba 2 Cu 3 O x superconductor tapes, which is more than three times higher than the J c typically obtained in moderately doped tapes. Pinning force levels above 1000 GN/m 3 have also been attained at 20 K. A composition map of lift factor in J c (ratio of J c at 30 K, 3 T to the J c at 77 K, 0 T) has been developed which reveals the optimum film composition to obtain lift factors above six, which is thrice the typical value. A highly c-axis aligned BaZrO 3 (BZO) nanocolumn defect density of nearly 7 × 10 11  cm −2 as well as 2–3 nm sized particles rich in Cu and Zr have been found in the high J c films

Bulk and nanocrystalline electron doped Gd{sub 0.15}Ca{sub 0.85}MnO{sub 3}: Synthesis and magnetic characterization

Energy Technology Data Exchange (ETDEWEB)

Dhal, Lakshman; Chattarpal [Department of Physics, Indian Institute of Technology Madras, Chennai 600 036 (India); Nirmala, R., E-mail: nirmala@iitm.ac.in [Department of Physics, Indian Institute of Technology Madras, Chennai 600 036 (India); Santhosh, P.N. [Department of Physics, Indian Institute of Technology Madras, Chennai 600 036 (India); Kumary, T. Geetha [CMPD, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Nigam, A.K. [Tata Institute of Fundamental Research, Mumbai 400 005 (India)

2014-09-01

Polycrystalline Gd{sub 0.15}Ca{sub 0.85}MnO{sub 3} sample was prepared by solid state reaction method and nanocrystalline samples of different grain sizes of the same were prepared by sol–gel method. Phase purity and composition were verified by room temperature X-ray diffraction and SEM-EDAX analysis. Magnetization data of bulk Gd{sub 0.15}Ca{sub 0.85}MnO{sub 3} in 5 kOe field shows a peak at ∼119 K (T{sub N}) suggesting an antiferromagnetic transition. Nanocrystalline Gd{sub 0.15}Ca{sub 0.85}MnO{sub 3} sample (∼54 nm size) also shows a cusp at ∼107 K and a broad thermal hysteresis between field cooled cooling (FCC) and field cooled warming (FCW) data around this temperature. This thermal hysteresis suggests possible crystal structural transition. Field variation of magnetization of bulk Gd{sub 0.15}Ca{sub 0.85}MnO{sub 3} at 5 K shows a tendency to saturate, but yields a magnetic moment value of only ∼1.12 μ{sub B}/f.u. in 70 kOe. The value of magnetization of nanocrystalline sample at 5 K in 70 kOe field is slightly larger and is ∼1.38 μ{sub B}/f.u. which is probably due to the surface moments of the nanoparticle samples. Both the samples show Curie–Weiss-like behaviour in their paramagnetic state.

Influence of soft ferromagnetic sections on the magnetic flux density profile of a large grain, bulk Y–Ba–Cu–O superconductor

International Nuclear Information System (INIS)

Philippe, M P; Wéra, L; Fagnard, J-F; Vanderheyden, B; Vanderbemden, P; Ainslie, M D; Dennis, A R; Shi, Y-H; Cardwell, D A

2015-01-01

Bulk, high temperature superconductors have significant potential for use as powerful permanent magnets in a variety of practical applications due to their ability to trap record magnetic fields. In this paper, soft ferromagnetic sections are combined with a bulk, large grain Y–Ba–Cu–O high temperature superconductor to form superconductor/ferromagnet hybrid structures. We study how the ferromagnetic sections influence the shape of the profile of the trapped magnetic induction at the surface of each structure and report the surface magnetic flux density measured by Hall probe mapping. These configurations have been modelled using a 2D axisymmetric finite element method based on the H-formulation and the results show excellent qualitative and quantitative agreement with the experimental measurements. The model has also been used to study the magnetic flux distribution and predict the behaviour for other constitutive laws and geometries. The results show that the ferromagnetic material acts as a magnetic shield, but the flux density and its gradient are enhanced on the face opposite to the ferromagnet. The thickness and saturation magnetization of the ferromagnetic material are important and a characteristic ferromagnet thickness d* is derived: below d*, saturation of the ferromagnet occurs, and above d*, a weak thickness-dependence is observed. The influence of the ferromagnet is observed even if its saturation magnetization is lower than the trapped flux density of the superconductor. Conversely, thin ferromagnetic discs can be driven to full saturation even though the outer magnetic field is much smaller than their saturation magnetization. (paper)

Direct images and unconventional dynamics of vortices in the high-Tc superconductors YBCO (123) and BSCCO (2212)

International Nuclear Information System (INIS)

Gammel, P.L.; Bishop, D.; Murray, C.; Huse, D.

1991-01-01

Static imaging has been used to complement transport I-V measurements in inferring the phase diagram and structure of the mixed state of the high T c superconductors YBCO(123) and BSCCO (2212). High resolution Bitter patterns reveal the static structure of the flux lattice in the low field mixed state of BSCCO (2212). For B parallel c, the in-plane effective mass anisotropy is found to distort the lattice. Rotation of the field away from the c axis results in the appearance of a unique structure: a striking array of vortex chains. At low fields, the pattern is otherwise amorphous. Increasing the field above ∼ 20G results in an abrupt transition into an hexatic phase. At high fields, I-V curves with picovolt resolution imply critical behavior within the mixed state, consistent in both 123 and 2212 with a three-dimensional vortex glass transition well below T c . In 2212, a field and temperature dependent crossover in the effective dimensionality of the vortex lattice is also found

Influence of superconductor film composition on adhesion strength of coated conductors

Energy Technology Data Exchange (ETDEWEB)

Kesgin, Ibrahim; Khatri, Narayan; Liu, Yuhao; Delgado, Louis; Galstyan, Eduard; Selvamanickam, Venkat

2015-11-20

The effect of high temperature superconductor (HTS) film composition on the adhesion strength of rare- earth barium copper oxide coated conductors (CCs) has been studied. It has been found that the mechanical integrity of the superconductor layer is very susceptible to the defects especially those along the ab plane, probably due to the weak interfaces between the defects and the matrix. Gd and Y in the standard composition were substituted with Sm and the number of in-plane defects was drastically reduced. Consequently, a four-fold increase in adhesion or peeling strength in Sm-based CCs was achieved compared to the standard GdYBCO samples.

Influence of superconductor film composition on adhesion strength of coated conductors

International Nuclear Information System (INIS)

Kesgin, Ibrahim; Khatri, Narayan; Liu, Yuhao; Delgado, Louis; Galstyan, Eduard; Selvamanickam, Venkat

2016-01-01

The effect of high temperature superconductor (HTS) film composition on the adhesion strength of rare-earth barium copper oxide coated conductors (CCs) has been studied. It has been found that the mechanical integrity of the superconductor layer is very susceptible to the defects especially those along the ab plane, probably due to the weak interfaces between the defects and the matrix. Gd and Y in the standard composition were substituted with Sm and the number of in-plane defects was drastically reduced. Consequently, a four-fold increase in adhesion or peeling strength in Sm-based CCs was achieved compared to the standard GdYBCO samples. (paper)

Recent development in crystal growth of large-diameter Y-QMG (reg sign) bulk superconductors; Y kei ogata QMG (reg sign) baruku koonchodendotai no kaihatsu jokyo

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, T.; Morita, M. [Nippon Steel Corporation, Tokyo (Japan); Masahashi, N. [Tohoku University, Miyagi (Japan). Institute for Materials Research

1999-11-25

The current status of large-diameter Y-Ba-Cu-O OMG(reg sign) bulk superconductors is described. 75 mm-diameter QMG(reg sign) samples with fairly concentric trapped-magnetic-flux-density distributions have been successfully grown. In addition, a record-high value of the magnetic levitation force, 171 kgf, measured at 77 K using a 90 mm-diameter Nd-Fe-B magnet has been obtained for a 100 mm-diameter sample. The crystal orientation of subgrains in the sample was determined using Electron Back-Scattering Diffraction as well as using a conventional optical apparatus including a He-Ne-laser. For the sample grown under normal process conditions, the maximum value of the [001]-axis misorientation angles at the subgrain-boundaries we obtained in the c-substructure region is 2.9 degree. However, in the a/b-substructure regions, the misorientation angles are larger, and the maximum value obtained is 6.6 degree, exceeding the critical angle at which a significant reduction of the critical current density occurs in Y123 thin films due to the weak-link problem. (author)

Improving magnetic properties of MgB{sub 2} bulk superconductors by synthetic engine oil treatment

Energy Technology Data Exchange (ETDEWEB)

Taylan Koparan, E., E-mail: etaylan20@gmail.com [Department of Science Education, Eregli Faculty of Education, Bulent Ecevit University, TR-67300, Zonguldak (Turkey); Savaskan, B. [Energy Systems Engineering, Faculty of Technology, Karadeniz Technical University, 61830, Of, Trabzon (Turkey); Yanmaz, E. [Department of Mechatronics, Faculty of Engineering and Architecture, İstanbul Gelişim University, İstanbul (Turkey)

2016-08-15

Highlights: • The effects of synthetic engine oil treatment on magnetic properties of bulk MgB{sub 2} superconductors has been first time investigated and reported. • Synthetic engine oil used as a product which is cheap and a rich carbon source obviously has improved the superconducting magnetic properties of MgB{sub 2}. • The critical current density of all of MgB{sub 2} samples immersed at different standby time in engine oil in whole field range has been better than that of the pure MgB{sub 2} sample. • The MgB{sub 2} sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. - Abstract: The present study focuses on the effects of standby time of the MgB{sub 2} samples immersed in synthetic engine oil on the critical current density ( J{sub c}(H)), magnetic field dependence of the pinning force density f{sub p}(b) and T{sub c} performances of MgB{sub 2} bulk superconductors. Synthetic engine oil was used as a product which is cheap and a rich carbon source. Manufactured MgB{sub 2} pellet samples were immersed at different standby time of 30 min, 120 min, 300 min and 1440 min in synthetic engine oil after the first heating process. Finally, MgB{sub 2} samples immersed in synthetic engine oil were sintered at 1000 °C and kept for 15 min in Ar atmosphere. The critical current density of all of MgB{sub 2} samples immersed at different standby time in engine oil in whole field range was better than that of the pure MgB{sub 2} sample because of the number of the pinning centers. The MgB{sub 2} sample immersed at 300 min standby time in synthetic engine oil has the best performance compared to other samples. The J{sub c} value for the pure sample is 2.0 × 10{sup 3} A/cm{sup 2}, whereas for the MgB{sub 2} sample immersed at 300 min standby time in engine oil the J{sub c} is enhanced to 4.8 × 10{sup 3} A/cm{sup 2} at 5 K and 3 T. The superconducting transition temperature (T{sub c}) did not change

Topological insulators/superconductors: Potential future electronic materials

International Nuclear Information System (INIS)

Hor, Y. S.

2014-01-01

A new material called topological insulator has been discovered and becomes one of the fastest growing field in condensed matter physics. Topological insulator is a new quantum phase of matter which has Dirac-like conductivity on its surface, but bulk insulator through its interior. It is considered a challenging problem for the surface transport measurements because of dominant internal conductance due to imperfections of the existing crystals of topological insulators. By a proper method, the internal bulk conduction can be suppressed in a topological insulator, and permit the detection of the surface currents which is necessary for future fault-tolerant quantum computing applications. Doped topological insulators have depicted a large variety of bulk physical properties ranging from magnetic to superconducting behaviors. By chemical doping, a TI can change into a bulk superconductor. Nb x Bi 2 Se 3 is shown to be a superconductor with T c ∼ 3.2 K, which could be a potential candidate for a topological superconductor

Growth anisotropy effect of bulk high temperature superconductors on the levitation performance in the applied magnetic field

International Nuclear Information System (INIS)

Zheng, J.; Liao, X.L.; Jing, H.L.; Deng, Z.G.; Yen, F.; Wang, S.Y.; Wang, J.S.

2013-01-01

Highlights: • The single-layer bulk HTSC with AGSBP obtains better levitation performance than that of MGSBP. • The double-layer bulk with AGSBP obtains better levitation performance than that of MGSBP too. • The double-layer bulk finding is contrast to MGSBP if pursuing high trapped field. • The optimization is highlighted by simple and easy operation, thus economical in the practice. -- Abstract: Growth anisotropies of bulk high temperature superconductors (HTSCs) fabricated by a top-seeded melt texture growth process, that is, different pinning effect in the growth sectors (GSs) and growth sector boundaries (GSBs), possess effect on the macro flux trapping and levitation performance of bulk HTSCs. Previous work (Physics Procedia, 36 (2012) 1043) has found that the bulk HTSC array with aligned GSB pattern (AGSBP) exhibits better capability for levitation and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP). In this paper, we further examine this growth anisotropy effect on the maglev performance of a double-layer bulk HTSC. In contrast to reported trapped flux cases (Supercond. Sci. Technol. 19 (2006) S466), the two superposed bulk HTSCs with same AGSBP with PMG are found to show better maglev performance. These series of results are helpful and support a new way for the performance optimization of present HTS maglev systems

Growth anisotropy effect of bulk high temperature superconductors on the levitation performance in the applied magnetic field

Energy Technology Data Exchange (ETDEWEB)

Zheng, J., E-mail: jzheng@swjtu.edu.cn; Liao, X.L.; Jing, H.L.; Deng, Z.G.; Yen, F.; Wang, S.Y.; Wang, J.S.

2013-10-15

Highlights: • The single-layer bulk HTSC with AGSBP obtains better levitation performance than that of MGSBP. • The double-layer bulk with AGSBP obtains better levitation performance than that of MGSBP too. • The double-layer bulk finding is contrast to MGSBP if pursuing high trapped field. • The optimization is highlighted by simple and easy operation, thus economical in the practice. -- Abstract: Growth anisotropies of bulk high temperature superconductors (HTSCs) fabricated by a top-seeded melt texture growth process, that is, different pinning effect in the growth sectors (GSs) and growth sector boundaries (GSBs), possess effect on the macro flux trapping and levitation performance of bulk HTSCs. Previous work (Physics Procedia, 36 (2012) 1043) has found that the bulk HTSC array with aligned GSB pattern (AGSBP) exhibits better capability for levitation and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP). In this paper, we further examine this growth anisotropy effect on the maglev performance of a double-layer bulk HTSC. In contrast to reported trapped flux cases (Supercond. Sci. Technol. 19 (2006) S466), the two superposed bulk HTSCs with same AGSBP with PMG are found to show better maglev performance. These series of results are helpful and support a new way for the performance optimization of present HTS maglev systems.

Effect of growth anisotropy on the morphology and property of directionally solidified RE123

International Nuclear Information System (INIS)

Nakamura, Yuichi; Shibusawa, Akira; Ooishi, Yoshihiro; Misu, Tomohiko; Inada, Ryoji; Oota, Akio

2005-01-01

The REBa 2 Cu 3 O y (RE123: RE = Y, Sm, Gd etc.) superconducting current lead is a favorable application due to the high J c properties and low thermal conductivity. Since the RE123 crystal shows the anisotropy in the J c properties as well as the mechanical properties, the ab-plane of the crystal parallel to the growth direction is preferable. The preferential growth direction during directional solidification is determined by the growth anisotropy in the early stage of the growth. In order to get the fundamental information to control the growth orientation, we investigated the growth rates of the Gd123 and Sm123 crystals against the undercooling and the continuous growth condition of Sm123 in directional solidification process. The growth rates of Sm123 and Gd123 were found to be about 5-10 times larger than that of Y123 at the same undercooling. The Sm123 showed the continuous growth structure up to 15 mm/h for fiber samples and up to 10 mm/h for 2 mm circle rods by the zone melting process. These pulling rates for continuous growth are larger than those of Y123 although the difference in growth rates between Sm123 and Y123 is much larger than this difference

Upper critical and irreversibility fields in Ni- and Co-doped pnictide bulk superconductors

Science.gov (United States)

Nikolo, Martin; Singleton, John; Solenov, Dmitry; Jiang, Jianyi; Weiss, Jeremy; Hellstrom, Eric

2018-05-01

A comprehensive study of upper critical and irreversibility magnetic fields in Ba(Fe0.95Ni0.05)2As2 (large grain and small grain samples), Ba(Fe0.94Ni0.06)2As2, Ba(Fe0.92Co0.08)2As2, and Ba(Fe0.92Co0.09)2As2 polycrystalline bulk pnictide superconductors was made in pulsed fields of up to 65 T. The full magnetic field-temperature (H-T) phase diagrams, starting at 1.5 K, were measured. The higher temperature, upper critical field Hc2 data are well described by the one-band Werthamer, Helfand, and Hohenberg (WHH) model. At low temperatures, the experimental data depart from the fitted WHH curves, suggesting an emergence of a new phase that could be attributed to the Fulde-Ferrell-Larkin-Ovchinnikov (FFLO) state. The large values of the Maki fitting parameter α indicate that the Zeeman pair breaking dominates over the orbital pair breaking and spin-paramagnetic pair-breaking effect is significant in these materials. Possible multi-band structure of these materials is lumped into effective parameters of the single-band model. Table of measured physical parameters allows us to compare these pnictide superconductors for different Co- and Ni- doping levels and granularity.

Electrical and structural properties of GdBa2Cu3-xVxO7-x

International Nuclear Information System (INIS)

Javanmard, H.; Bazargan, S.; Akhavan, M.

2007-01-01

Full text: It is well known that the characteristics of the CuO 2 planes are essential for understanding the unconventional superconductivity and the anomalous transport behavior of the normal state in cuprate superconductors. Continuous efforts have been devoted to the study of effects of substitution for Cu, which are of great importance for understanding the role of Cu in high-Tc superconductivity. The bulk samples of GdBa 2 Cu 3-x V x O 7-x with 0.0 4+ in the compound, and because of the high tendency of the V 4+ for achieving the octahedral structure, it appears that vanadium enters the chains, which accounts for the observed changes in the crystal structure and superconducting properties. (authors)

FY 1998 report on the results of the research and development of fundamental technologies for superconductor applications; 1998 nendo chodendo oyo kiban gijutsu kenkyukaihatsu seika hokokusho. Chodendo oyo kiban gijutsu keknyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

As to the research on the superconductor manifestation mechanism, Y123 monocrystal which was partially replaced with Zn and Ni was manufactured, and it was made clear that the addition of these impurities greatly change anisotropy of superconductors. It was made clear that instability of lattice and magnetism is included in high temperature superconductor. Also made clear was an important role in the Nb/Ba replacement in existence of magnetic flux melting phase transfer and the magnetic field induced pinning effect. The manufacture of Y123 bicrystal membrane was successful by the liquid phase epitaxy method. The manufacture of non-copper base K-Bi-O new superconductor was successful by the ultra-high pressure synthesis method. The stabilized process was established for large size crystals of 15-20mm square in Y base and of 20-25mm square in Nd base. Also successful was the growth by LPE method of crystal with thick membrane of 20mm x 20mm x 10{mu}m on the MgO monocrystal substrate. The non-bicrystalization of Y base Nd base monocrystal was successful, and the peak phenomenon control in Jc-H was found out. By neutron irradiation, the acquisition magnetic field of 3.7T at 77K was achieved using bulk Y base 123 material with diameter of 3cm. And, the critical current density of 60,000 A/cm{sup 2} was achieved at 77K and 3T. (NEDO)

Effect of Annealing to the Formation of The 123 Phase YBa2Cu3O7-x Superconductor Produced by High Energy Milling

International Nuclear Information System (INIS)

Didin S Winatapura; Yustinus P, Wisnu A.A; Sukirman, E.

2008-01-01

Effect of annealing to the formation of 123 phase YBa 2 Cu 3 O 7-x superconductor produced by high energy milling (HEM) has been investigated. The milling process by using HEM method was performed for 30 hours, and followed by annealing at 500 o C, 600 o C, and 700 o C for 10 hours. The phase quality and quantity inside the specimen was measured by X-rays diffraction technique (XRD), and analyzed using Rietveld method. The microstructure of the specimen was observed with Scanning Electron Microscope (SEM), and electric property of the specimen was measured with four point probe. The result showed that the milling for 30 hours caused the deformation and partial decomposition of 123 phase resulting in another phase. The anneal effect caused the recrystallization process of decomposed 123 phase in such away that reformed 123 phase having finer crystallite size. According to the calculation using the Hall-Williamson's equation, the diameter of the crystallite size, D was obtained of about 496 Armstrong for milled specimen, and D ∼ 1,714 Armstrong for sintered specimen. By decreasing the 123 phase grain size, the intergrain contact surface became larger. It means that the intergrain link of 123 phase became stronger. The critical current (density) of milled specimen was obtained as J c ∼23.74 A.cm -2 , and J c ∼ 3.18 A.cm -2 for sintered specimen. Thus, the transport current that flowed intergrain inside 123 phase increased.(author)

Effects of the APC materials on c-axis correlated pinning effects in a-axis oriented Y123/2D APC multilayer films

International Nuclear Information System (INIS)

Takamura, M.; Mukaida, M.; Horii, S.; Ichinose, A.; Kita, R.; Namba, M.; Awaji, S.; Watanabe, K.; Matsumoto, K.; Yoshida, Y.; Teranishi, R.; Yamada, K.; Mori, N.

2009-01-01

For a-axis oriented and c-axis in-plane aligned YBa 2 Cu 3 O 7-δ /artificial pinning center (Y123/APC) alternately-layered thin films, effects of the APC materials on the multilayer structures are discussed. Pr123, (Y 1-x Pr x )123 and Gd 2 CuO 4 (Gd214) were used as APCs. The multilayer structure was observed for Y123/Pr123 films and Y123/Gd214 films. However, some grains are also grown in the Y123/Gd214 film. For the Y123/Pr123 multilayer film, each Pr123 layer act as two-dimensional APCs (2D APCs) in the magnetic field angular dependences of the critical current density. The growth mechanism of the multilayer structure in the Y123/2D APC films is discussed by a transmission electron microscopy and an atomic force microscope. It is found that two conditions are needed to obtain the c-axis correlated pinning effects by 2D APC in the a-axis oriented and c-axis in-plane aligned Y123/APC multilayer films: the same structure as Y123; Y-free APC materials.

An efficient and economical way to enhance the performance of present HTS Maglev systems by utilizing the anisotropy property of bulk superconductors

International Nuclear Information System (INIS)

Deng Zigang; Wang Jiasu; Zheng Jun; Zhang Ya; Wang Suyu

2013-01-01

We report a simple, efficient and economical way to enhance the levitation or guidance performance of present high-temperature superconducting (HTS) Maglev systems by exploring the anisotropic properties of the critical current density in the a–b plane and along the c-axis of bulk superconductors. In the method, the bulk laying mode with different c-axis directions is designed to match with the magnetic field configuration of the applied permanent magnet guideway (PMG). Experimental results indicate that more than a factor of two improvement in the levitation force or guidance force is achieved when changing the laying mode of bulk superconductors from the traditional fashion of keeping the c-axis vertical to the PMG surface to the studied one of keeping the c-axis parallel to the PMG surface, at the maximum horizontal and vertical magnetic field positions of the PMG, respectively. These phenomena resulted from the physical nature of the generated levitation force and guidance force (electromagnetic forces) and the fact that there are different critical current densities in the a–b plane and along the c axis. Based on the experimental results, new HTS Maglev systems can be designed to meet the requirements of practical heavy-load or curved-route applications. (paper)

An efficient and economical way to enhance the performance of present HTS Maglev systems by utilizing the anisotropy property of bulk superconductors

Science.gov (United States)

Deng, Zigang; Wang, Jiasu; Zheng, Jun; Zhang, Ya; Wang, Suyu

2013-02-01

We report a simple, efficient and economical way to enhance the levitation or guidance performance of present high-temperature superconducting (HTS) Maglev systems by exploring the anisotropic properties of the critical current density in the a-b plane and along the c-axis of bulk superconductors. In the method, the bulk laying mode with different c-axis directions is designed to match with the magnetic field configuration of the applied permanent magnet guideway (PMG). Experimental results indicate that more than a factor of two improvement in the levitation force or guidance force is achieved when changing the laying mode of bulk superconductors from the traditional fashion of keeping the c-axis vertical to the PMG surface to the studied one of keeping the c-axis parallel to the PMG surface, at the maximum horizontal and vertical magnetic field positions of the PMG, respectively. These phenomena resulted from the physical nature of the generated levitation force and guidance force (electromagnetic forces) and the fact that there are different critical current densities in the a-b plane and along the c axis. Based on the experimental results, new HTS Maglev systems can be designed to meet the requirements of practical heavy-load or curved-route applications.

Flux motion in Y-Ba-Cu-O bulk superconductors during pulse field magnetization

International Nuclear Information System (INIS)

Yoshizawa, K; Nariki, S; Sakai, N; Murakami, M; Hirabayasi, I; Takizawa, T

2004-01-01

We have studied the relationship between the magnetization and temperature change in Y-Ba-Cu-O bulk superconductor during pulse field magnetization (PFM). The flux motion was monitored using both Hall sensors and pick-up coils that are placed on a surface of a Y-Ba-Cu-O disc having dimensions of 15 mm in diameter and 0.95 mm in thickness. The peak value of the field was varied from 0.2 to 0.8 T. The effect of the static bias field was also studied in the range of 0-3 T. The temperature of the sample surface was measured using a resistance temperature sensor. The temperature increased with the magnitude of the applied pulsed magnetic field, and the amount of temperature rise decreased with increasing static bias field

The effect of magnet size on the levitation force and attractive force of single-domain YBCO bulk superconductors

International Nuclear Information System (INIS)

Yang, W M; Chao, X X; Bian, X B; Liu, P; Feng, Y; Zhang, P X; Zhou, L

2003-01-01

The levitation forces between a single-domain YBCO bulk and several magnets of different sizes have been measured at 77 K to investigate the effect of the magnet size on the levitation force. It is found that the levitation force reaches a largest (peak) value when the size of the magnet approaches that of the superconductor when the other conditions are fixed. The absolute maximum attractive force (in the field-cooled state) increases with the increasing of the magnet size, and is saturated when the magnet size approaches that of the superconductor. The maximum attractive force in the field-cooled (FC) state is much higher than that of the maximum attractive force in the zero field-cooled (ZFC) state. The results indicate that the effects of magnetic field distribution on the levitation force have to be considered during the designing and manufacturing of superconducting devices

Topological surface states in nodal superconductors.

Science.gov (United States)

Schnyder, Andreas P; Brydon, Philip M R

2015-06-24

Topological superconductors have become a subject of intense research due to their potential use for technical applications in device fabrication and quantum information. Besides fully gapped superconductors, unconventional superconductors with point or line nodes in their order parameter can also exhibit nontrivial topological characteristics. This article reviews recent progress in the theoretical understanding of nodal topological superconductors, with a focus on Weyl and noncentrosymmetric superconductors and their protected surface states. Using selected examples, we review the bulk topological properties of these systems, study different types of topological surface states, and examine their unusual properties. Furthermore, we survey some candidate materials for topological superconductivity and discuss different experimental signatures of topological surface states.

Topological surface states in nodal superconductors

International Nuclear Information System (INIS)

Schnyder, Andreas P; Brydon, Philip M R

2015-01-01

Topological superconductors have become a subject of intense research due to their potential use for technical applications in device fabrication and quantum information. Besides fully gapped superconductors, unconventional superconductors with point or line nodes in their order parameter can also exhibit nontrivial topological characteristics. This article reviews recent progress in the theoretical understanding of nodal topological superconductors, with a focus on Weyl and noncentrosymmetric superconductors and their protected surface states. Using selected examples, we review the bulk topological properties of these systems, study different types of topological surface states, and examine their unusual properties. Furthermore, we survey some candidate materials for topological superconductivity and discuss different experimental signatures of topological surface states. (topical review)

Control of Y-211 content in bulk YBCO superconductors fabricated by a buffer-aided, top seeded infiltration and growth melt process

International Nuclear Information System (INIS)

Namburi, Devendra K; Shi, Yunhua; Palmer, Kysen G; Dennis, Anthony R; Durrell, John H; Cardwell, David A

2016-01-01

Bulk (RE)–Ba–Cu–O ((RE)BCO, where RE stands for rare-earth), single grain superconductors can trap magnetic fields of several tesla at low temperatures and therefore can function potentially as high field magnets. Although top seeded melt growth (TSMG) is an established process for fabricating relatively high quality single grains of (RE)BCO for high field applications, this technique suffers from inherent problems such as sample shrinkage, a large intrinsic porosity and the presence of (RE) 2 BaCuO 5 (RE-211)-free regions in the single grain microstructure. Seeded infiltration and growth (SIG), therefore, has emerged as a practical alternative to TSMG that overcomes many of these problems. Until now, however, the superconducting properties of bulk materials processed by SIG have been inferior to those fabricated using the TSMG technique. In this study, we identify that the inferior properties of SIG processed bulk superconductors are related to the presence of a relatively large Y-211 content (∼41.8%) in the single grain microstructure. Controlling the RE-211 content in SIG bulk samples is particularly challenging because it is difficult to regulate the entry of the liquid phase into the solid RE-211 preform during the infiltration process. In an attempt to solve this issue, we have investigated the effect of careful control of both the infiltration temperature and the quantity of liquid phase powder present in the sample preforms prior to processing. We conclude that careful control of the infiltration temperature is the most promising of these two process variables. Using this knowledge, we have fabricated successfully a YBCO bulk single grain using the SIG process of diameter 25 mm that exhibits a trapped field of 0.69 T at 77 K, which is the largest value reported to date for a sample fabricated by the SIG technique. (paper)

Canted magnetic moments at the Gd(0001) surface

International Nuclear Information System (INIS)

Li Donggi; Zhang Jiandi; Dowben, P.A.; Tang, H.; Walker, T.G.; Hopster, H.

1993-01-01

With spin polarized electron spectroscopies, the authors have investigated ordered Gd(0001) films deposited on W(110). The photoemission features of the gadolinium 5d surface state, the 4f levels, and the background exhibit considerable spin polarization along the same direction in the plane of the film, indicative of ferromagnetic coupling between the surface and the bulk. The 4f spin polarized photoemission data provides strong evidence that the surface 4f polarization differs from the bulk 4f polarization for Gd(0001). The temperature dependent measurements with spin polarized secondary electron spectroscopy conclusively establishes that the surface of clean Gd(0001) possesses a perpendicular polarization component which persists to an enhanced surface Curie temperature. Small amounts of contamination at the surface result in the disappearance of the perpendicular component and, therefore, a more perfect ferromagnetic coupling between the surface and the bulk

Microgravity Processing of Oxide Superconductors

Science.gov (United States)

Olive, James R.; Hofmeister, William H.; Bayuzick, Robert J.; Vlasse, Marcus

1999-01-01

Considerable effort has been concentrated on the synthesis and characterization of high T(sub c) oxide superconducting materials. The YBaCuO system has received the most intense study, as this material has shown promise for the application of both thin film and bulk materials. There are many problems with the application of bulk materials- weak links, poor connectivity, small coherence length, oxygen content and control, environmental reactivity, phase stability, incongruent melting behavior, grain boundary contamination, brittle mechanical behavior, and flux creep. The extent to which these problems are intrinsic or associated with processing is the subject of controversy. This study seeks to understand solidification processing of these materials, and to use this knowledge for alternative processing strategies, which, at the very least, will improve the understanding of bulk material properties and deficiencies. In general, the phase diagram studies of the YBaCuO system have concentrated on solid state reactions and on the Y2BaCuO(x) + liquid yields YBa2Cu3O(7-delta) peritectic reaction. Little information is available on the complete melting relations, undercooling, and solidification behavior of these materials. In addition, rare earth substitutions such as Nd and Gd affect the liquidus and phase relations. These materials have promising applications, but lack of information on the high temperature phase relations has hampered research. In general, the understanding of undercooling and solidification of high temperature oxide systems lags behind the science of these phenomena in metallic systems. Therefore, this research investigates the fundamental melting relations, undercooling, and solidification behavior of oxide superconductors with an emphasis on improving ground based synthesis of these materials.

Powder processing of high Tc oxide superconductors and their properties

International Nuclear Information System (INIS)

Vajpei, A.C.; Upadhyaya, G.S.

1992-01-01

Powder processing of ceramics is an established technology and in the area of high T c superconductors, its importance is felt even more significantly. The present monograph is an attempt in this direction to explore the perspectives and practice of powder processing routes towards control and optimization of the microstructure and pertinent properties of high T c oxide superconductors. The monograph consists of 6 chapters. After a very brief introduction (Chapter 1), Chapter 2 describes various classes of high T c oxide superconductors and their phase equilibria. Chapter 3 highlights the preparation of oxide superconductor powders through various routes and details their subtle distinctions. Chapter 4 briefly covers characterisation of the oxide superconductors, laying emphasis on the process-analysis and microstructure. Chapter 5 describes in detail various fabrication techniques for bulk superconductors through the powder routes. The last Chapter (Chapter 6) describing properties of bulk oxide superconductors, discusses the role of subtituents, compositional variations and processing methods on such properties. References are given at the end of each chapter. (orig.)

Alternating-current transport losses of melt-cast processed Bi-2212 bulk superconductor bars

International Nuclear Information System (INIS)

Tsukamoto, T; Inada, R; Inagaki, N; Andoh, H; Sugiura, T; Oota, A

2003-01-01

Using a melt-casting method, we have fabricated two pieces of Bi-2212 bulk superconductor bar with square and rectangular cross-sections, and we have investigated the alternating-current (ac) transport self-field losses at 77 K. Despite the main contribution of hysteresis loss of the superconductor, there is some difference in the loss behaviour between these two samples. To elucidate the origin, we make numerical calculations on the ac transport self-field losses as a function of current amplitude I 0 below the critical current I c . At a fixed I 0 , the calculated values using the uniform J c distribution and the actual cross-sectional geometry are much higher than the experimental data for the sample with a square cross-section 7.5 x 7.5 mm 2 , while there is good agreement between the calculation and the experiment for the sample with a rectangular cross-section 4.5 x 13.6 mm 2 . The discrepancy appearing in the sample with a square cross-section is ascribed to the actual J c distribution, which is confirmed by critical current measurements when scraping off the sample. The local J c value decreases significantly in going from the surface to the interior of the sample. This suppresses the extension of the flux-penetration region to the interior under ac current transmission and lowers the loss generation compared with the calculated results obtained by the uniform J c distribution

Unoccupied surface electronic structure of Gd(0001)

International Nuclear Information System (INIS)

Li, D.; Dowben, P.A.; Ortega, J.E.; Himpsel, F.J.

1994-01-01

The unoccupied surface electronic structure of Gd(0001) was investigated with high-resolution inverse-photoemission spectroscopy. An empty surface state near E F is observed at bar Γ. Two other surface-sensitive features are also revealed at 1.2 and 3.1 eV above the Fermi level. Hydrogen adsorption on Gd surfaces was used to distinguish the surface-sensitive features from the bulk features. The unoccupied bulk-band critical points are determined to be Γ 3 + at 1.9 eV and A 1 at 0.8 eV

Development of the cryo-rotary joint for a HTS synchronous motor with Gd-bulk HTS field-pole magnets

International Nuclear Information System (INIS)

Miki, M; Felder, B; Tsuzuki, K; Izumi, M; Hayakawa, H

2010-01-01

We have studied a prototype of an axial-gap type synchronous motor with Gd-bulk HTS field-pole magnets since 2001. At the liquid nitrogen temperature, these bulks have trapped over 1 T inside the motor after being applied the pulsed field magnetization method. Increasing the flux of the field poles is the most straightforward way of improving the output power of the motor. Cooling down the bulk HTS magnets below the liquid nitrogen temperature provides an effective alternative to increase the magnetic flux trapping. In 2007, we exchanged the cryogen from liquid nitrogen to condensed neon. The key technology of this challenge is a rotary joint, introducing a fluid cryogen into the rotating body in the motor from the static reservoir. We have successfully developed a compact rotary joint which is smaller and lighter than the existent one (1/10 volume, 1/3 length and 1/12 weight). The present joint was manufactured and evaluated with liquid nitrogen and condensed neon. We presume a total heat loss of this rotary joint of less than 10 watts. Successful cooling and rotating tests of the bulk-HTS motor with this novel rotary joint are conducted.

Development of the cryo-rotary joint for a HTS synchronous motor with Gd-bulk HTS field-pole magnets

Energy Technology Data Exchange (ETDEWEB)

Miki, M; Felder, B; Tsuzuki, K; Izumi, M [Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, 2-1-6, Etchu-jima, Koto-ku, Tokyo 135-8533 (Japan); Hayakawa, H, E-mail: d082025@kaiyodai.ac.j [Kitano Seiki Co. Ltd., 7-17-3, Chuo, Ohta-ku, Tokyo 143-0024 (Japan)

2010-06-01

We have studied a prototype of an axial-gap type synchronous motor with Gd-bulk HTS field-pole magnets since 2001. At the liquid nitrogen temperature, these bulks have trapped over 1 T inside the motor after being applied the pulsed field magnetization method. Increasing the flux of the field poles is the most straightforward way of improving the output power of the motor. Cooling down the bulk HTS magnets below the liquid nitrogen temperature provides an effective alternative to increase the magnetic flux trapping. In 2007, we exchanged the cryogen from liquid nitrogen to condensed neon. The key technology of this challenge is a rotary joint, introducing a fluid cryogen into the rotating body in the motor from the static reservoir. We have successfully developed a compact rotary joint which is smaller and lighter than the existent one (1/10 volume, 1/3 length and 1/12 weight). The present joint was manufactured and evaluated with liquid nitrogen and condensed neon. We presume a total heat loss of this rotary joint of less than 10 watts. Successful cooling and rotating tests of the bulk-HTS motor with this novel rotary joint are conducted.

Luminescent GdVO_4:Sm"3"+ quantum dots enhance power conversion efficiency of bulk heterojunction polymer solar cells by Förster resonance energy transfer

International Nuclear Information System (INIS)

Bishnoi, Swati; Gupta, Vinay; Sharma, Gauri D.; Chand, Suresh; Sharma, Chhavi; Kumar, Mahesh; Haranath, D.; Naqvi, Sheerin

2016-01-01

In this work, we report enhanced power conversion efficiency (PCE) of bulk heterojunction polymer solar cells by Förster resonance energy transfer (FRET) from samarium-doped luminescent gadolinium orthovanadate (GdVO_4:Sm"3"+) quantum dots (QDs) to polythieno[3,4-b]-thiophene-co-benzodithiophene (PTB7) polymer. The photoluminescence emission spectrum of GdVO_4:Sm"3"+ QDs overlaps with the absorption spectrum of PTB7, leading to FRET from GdVO_4:Sm"3"+ to PTB7, and significant enhancements in the charge-carrier density of excited and polaronic states of PTB7 are observed. This was confirmed by means of femtosecond transient absorption spectroscopy. The FRET from GdVO_4:Sm"3"+ QDs to PTB7 led to a remarkable increase in the power conversion efficiency (PCE) of PTB7:GdVO_4:Sm"3"+:PC_7_1BM ([6,6]-phenyl-C_7_1-butyric acid methyl ester) polymer solar cells. The PCE in optimized ternary blend PTB7:GdVO_4:Sm"3"+:PC_7_1BM (1:0.1:1.5) is increased to 8.8% from 7.2% in PTB7:PC_7_1BM. This work demonstrates the potential of rare-earth based luminescent QDs in enhancing the PCE of polymer solar cells.

Glass formation ability, structure and magnetocaloric effect of a heavy rare-earth bulk metallic glassy Gd{sub 55}Co{sub 20}Fe{sub 5}Al{sub 20} alloy

Energy Technology Data Exchange (ETDEWEB)

Jo, C.-L. [Shanghai University, School of Materials Science and Engineering, Yanchang Road 149, Zhabei District, 200072 Shanghai (China)], E-mail: jochollong@163.com; Xia Lei; Ding Ding; Dong Yuanda; Gracien, Ekoko [Shanghai University, School of Materials Science and Engineering, Yanchang Road 149, Zhabei District, 200072 Shanghai (China)

2008-06-30

The glass formation ability, the structure and the magnetocaloric effect of the bulk metallic glassy Gd{sub 55}Co{sub 20}Fe{sub 5}Al{sub 20} alloy were investigated. Bulk metallic glassy (BMGs) alloys were prepared by a copper-mold casting method. The glass forming ability and their structure were studied by using X-ray diffraction (XRD) and differential scanning calorimeter (DSC). The XRD analysis revealed that the as-cast cylinder of Gd{sub 55}Co{sub 20}Fe{sub 5}Al{sub 20} alloy showed fully amorphous structure in 2 mm diameter. The DSC revealed that the bulk cylinder of the Gd{sub 55}Co{sub 20}Fe{sub 5}Al{sub 20} alloy showed a distinct glass transition temperature and a relatively wide supercooled liquid region before crystallization. SQUID investigated the magnetic properties and the entropy changes. The Curie temperature of Gd{sub 55}Co{sub 20}Fe{sub 5}Al{sub 20} BMGs alloy was about 130 K, but the maximum magnetic entropy changes(-{delta}S{sub M}) showed at about 125 K, a little lower than the Curie temperature 130 K. The reason could probably be due to the presence of a little amount of nanocrystalline particles between amorphous phases. The BMG alloy has the characteristic of second-order transition (SOT) on Arrott plots. The results showed that the amorphous sample had a relatively improved magnetocaloric effect, indicating that the amorphous alloy could be considered as a candidate for magnetic refrigeration applications in the temperature interval range of 100-200 K.

Gd-HOPO Based High Relaxivity MRI Contrast Agents

Energy Technology Data Exchange (ETDEWEB)

Datta, Ankona; Raymond, Kenneth

2008-11-06

Tris-bidentate HOPO-based ligands developed in our laboratory were designed to complement the coordination preferences of Gd{sup 3+}, especially its oxophilicity. The HOPO ligands provide a hexadentate coordination environment for Gd{sup 3+} in which all he donor atoms are oxygen. Because Gd{sup 3+} favors eight or nine coordination, this design provides two to three open sites for inner-sphere water molecules. These water molecules rapidly exchange with bulk solution, hence affecting the relaxation rates of bulk water olecules. The parameters affecting the efficiency of these contrast agents have been tuned to improve contrast while still maintaining a high thermodynamic stability for Gd{sup 3+} binding. The Gd- HOPO-based contrast agents surpass current commercially available agents ecause of a higher number of inner-sphere water molecules, rapid exchange of inner-sphere water molecules via an associative mechanism, and a long electronic relaxation time. The contrast enhancement provided by these agents is at least twice that of commercial contrast gents, which are based on polyaminocarboxylate ligands.

Enhanced room temperature multiferroicity in Gd doped BFO

CSIR Research Space (South Africa)

Pradhan, SK

2009-01-01

Full Text Available deficient Gd doped multiferroic BFO system. At particular doping level of Gd, this bulk ceramics showed spectacular M~H behavior at room temperature which is likely to open a new avenue for the potential applications in information storing technology as well...

Thickness dependence of the levitation performance of double-layer high-temperature superconductor bulks above a magnetic rail

International Nuclear Information System (INIS)

Sun, R.X.; Zheng, J.; Liao, X.L.; Che, T.; Gou, Y.F.; He, D.B.; Deng, Z.G.

2014-01-01

Highlights: • Thickness optimization of double-layer bulk HTSC arrangement is studied. • The new bulk HTSC arrangement makes better use of the flux distribution of the magnetic rails. • Levitation performance can be enhanced with the optimization. • The optimization can meet large levitation force requirements for HTS Maglev system. - Abstract: A double-layer high-temperature superconductor (HTSC) arrangement was proposed and proved to be able to bring improvements to both levitation force and guidance force compared with present single-layer HTSC arrangement. To fully exploit the applied magnetic field by a magnetic rail, the thickness dependence of a double-layer HTSC arrangement on the levitation performance was further investigated in the paper. In this study, the lower-layer bulk was polished step by step to different thicknesses, and the upper-layer bulk with constant thickness was directly superimposed on the lower-layer one. The levitation force and the force relaxation of the double-layer HTSC arrangement were measured above a Halbach magnetic rail. Experimental result shows that a bigger levitation force and a less levitation force decay could be achieved by optimizing the thickness of the lower-layer bulk HTSC. This thickness optimization method could be applied together with former reported double-layer HTSC arrangement method with aligned growth sector boundaries pattern. This series of study on the optimized combination method do bring a significant improvement on the levitation performance of present HTS maglev systems

Thickness dependence of the levitation performance of double-layer high-temperature superconductor bulks above a magnetic rail

Energy Technology Data Exchange (ETDEWEB)

Sun, R.X.; Zheng, J.; Liao, X.L.; Che, T.; Gou, Y.F.; He, D.B.; Deng, Z.G., E-mail: zgdeng@gmail.com

2014-10-15

Highlights: • Thickness optimization of double-layer bulk HTSC arrangement is studied. • The new bulk HTSC arrangement makes better use of the flux distribution of the magnetic rails. • Levitation performance can be enhanced with the optimization. • The optimization can meet large levitation force requirements for HTS Maglev system. - Abstract: A double-layer high-temperature superconductor (HTSC) arrangement was proposed and proved to be able to bring improvements to both levitation force and guidance force compared with present single-layer HTSC arrangement. To fully exploit the applied magnetic field by a magnetic rail, the thickness dependence of a double-layer HTSC arrangement on the levitation performance was further investigated in the paper. In this study, the lower-layer bulk was polished step by step to different thicknesses, and the upper-layer bulk with constant thickness was directly superimposed on the lower-layer one. The levitation force and the force relaxation of the double-layer HTSC arrangement were measured above a Halbach magnetic rail. Experimental result shows that a bigger levitation force and a less levitation force decay could be achieved by optimizing the thickness of the lower-layer bulk HTSC. This thickness optimization method could be applied together with former reported double-layer HTSC arrangement method with aligned growth sector boundaries pattern. This series of study on the optimized combination method do bring a significant improvement on the levitation performance of present HTS maglev systems.

Thermoluminescence and dielectric response of LiKSO{sub 4}:Gd to {gamma}-radiation

Energy Technology Data Exchange (ETDEWEB)

El-Kolaly, M.A.; Kassem, M.E.; Higazy, A.A.; Ismail, L.Z.; Al-Houty, L.I. [Qatar Univ., Doha (Qatar). Dept. of Physics

1994-10-01

The effect of {gamma}-radiation dose up to about 324 kGy on the thermoluminescence and dielectric properties of LiKSO{sub 4}:Gd was studied. All glow curves exhibited a single peak around 373 K. The activation energy of this peak was estimated to be about 0.82 eV. The variation of the TL intensity with {gamma}-dose is characterized by a maximum at 6.75 kGy. The dielectric dispersion was studied as a function of irradiation dose. In the low frequency range straight line behaviour was obtained for low dose (up to 12.3 kGy) while for higher {gamma}-dose, semicircles are obtained. The bulk conductivity was found to increase with dose up to 6.75 kGy. (author).

Anomalous Josephson Effect between Even-and Odd-Frequency Superconductors

NARCIS (Netherlands)

Tanaka, Yukio; Golubov, Alexandre Avraamovitch; Kashiwaya, Satoshi; Ueda, Masahito

2007-01-01

We demonstrate that, contrary to standard wisdom, the lowest-order Josephson coupling is possible between odd- and even-frequency superconductors. The origin of this effect is the induced odd- (even-)frequency pairing component at the interface of bulk even- (odd-)frequency superconductors. The

Granular Superconductors and Gravity

Science.gov (United States)

Noever, David; Koczor, Ron

1999-01-01

As a Bose condensate, superconductors provide novel conditions for revisiting previously proposed couplings between electromagnetism and gravity. Strong variations in Cooper pair density, large conductivity and low magnetic permeability define superconductive and degenerate condensates without the traditional density limits imposed by the Fermi energy (approx. 10(exp -6) g cu cm). Recent experiments have reported anomalous weight loss for a test mass suspended above a rotating Type II, YBCO superconductor, with a relatively high percentage change (0.05-2.1%) independent of the test mass' chemical composition and diamagnetic properties. A variation of 5 parts per 104 was reported above a stationary (non-rotating) superconductor. In experiments using a sensitive gravimeter, bulk YBCO superconductors were stably levitated in a DC magnetic field and exposed without levitation to low-field strength AC magnetic fields. Changes in observed gravity signals were measured to be less than 2 parts in 108 of the normal gravitational acceleration. Given the high sensitivity of the test, future work will examine variants on the basic magnetic behavior of granular superconductors, with particular focus on quantifying their proposed importance to gravity.

Collection of Ni-bearing material from electroless plating waste by magnetic separation with HTS bulk magnet

Science.gov (United States)

Oka, T.; Fukazawa, H.; Fukui, S.; Ogawa, J.; Sato, T.; Ooizumi, M.; Tsujimura, M.; Yokoyama, K.

2014-01-01

The magnetic separation experiment to collect the Ni compounds from the waste liquid of electroless plating processes was conducted in the open-gradient magnetic separation process with the high temperature superconducting bulk magnet system. The magnetic pole containing Gd-based bulk superconductors was activated to 3.45 T at 35 K in the static magnetic field of 5 T with use of a superconducting solenoid magnet. The coarse Ni-sulfate crystals were formed by adding the concentrated sulfuric acid to the Ni-phosphite precipitates which yielded from the plating waste liquid by controlling the temperature and the pH value. The open-gradient magnetic separation technique was employed to separate the Ni-sulfate crystals from the mixture of the Ni-sulfate and Ni-phosphite compounds by the difference between their magnetic properties. And we succeeded in collecting Ni-sulfate crystals preferentially to the Ni-phosphite by attracting them to the magnetic pole soon after the Ni-sulfate crystals began to grow.

Correlations Between Magnetic Flux and Levitation Force of HTS Bulk Above a Permanent Magnet Guideway

Science.gov (United States)

Huang, Huan; Zheng, Jun; Zheng, Botian; Qian, Nan; Li, Haitao; Li, Jipeng; Deng, Zigang

2017-10-01

In order to clarify the correlations between magnetic flux and levitation force of the high-temperature superconducting (HTS) bulk, we measured the magnetic flux density on bottom and top surfaces of a bulk superconductor while vertically moving above a permanent magnet guideway (PMG). The levitation force of the bulk superconductor was measured simultaneously. In this study, the HTS bulk was moved down and up for three times between field-cooling position and working position above the PMG, followed by a relaxation measurement of 300 s at the minimum height position. During the whole processes, the magnetic flux density and levitation force of the bulk superconductor were recorded and collected by a multipoint magnetic field measurement platform and a self-developed maglev measurement system, respectively. The magnetic flux density on the bottom surface reflected the induced field in the superconductor bulk, while on the top, it reveals the penetrated magnetic flux. The results show that the magnetic flux density and levitation force of the bulk superconductor are in direct correlation from the viewpoint of inner supercurrent. In general, this work is instructive for understanding the connection of the magnetic flux density, the inner current density and the levitation behavior of HTS bulk employed in a maglev system. Meanwhile, this magnetic flux density measurement method has enriched present experimental evaluation methods of maglev system.

Relationship between critical current properties and microstructure in cylindrical RE123 melt-solidified bulks

International Nuclear Information System (INIS)

Nakashima, T.; Shimoyama, J.; Honzumi, M.; Tazaki, Y.; Horii, S.; Kishio, K.

2005-01-01

We report the synthesis of cylindrical melt-solidified bulks in REBa 2 Cu 3 O y (RE = Sm, Gd, Dy, Ho, Y and Er), and their critical current properties and microstructures of the a- and the c-growth regions. It was found from the microstructure analysis that the volume fractions of RE211 particles in the c-growth region were always lower than those in the a-growth region. Moreover, those in the c-growth region were increased with distance from the seed crystal. Interestingly, the second peak effects in J c -B curves were prominently enhanced for the c-growth region. J c values at zero field for the c-growth region through the appropriate oxygen post-annealing reached approximately 95 kA cm -2 for RE = Ho, Dy and Y

Development of superconductor application technology

Energy Technology Data Exchange (ETDEWEB)

Hong, G W; Kim, C J; Lee, H G; Lee, H J; Kim, K B; Won, D Y; Jang, K I; Kwon, S C; Kim, W J; Ji, Y A; Yang, S W; Kim, W K; Park, S D; Lee, M H; Lee, D M; Park, H W; Yu, J K; Lee, I S; Kim, J J; Choi, H S; Chu, Y; Kim, Y S; Kim, D H

1997-09-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype flywheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies onthe method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting power with good reactivity and fine particle size was obtained by mechanical grinding, control of phase assemblage, and emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Jc of 20,000 A/cm{sup 2} was fabricated by applying CIP packing procedure. Multifilamentary wire with Jc of 10,000 A/cm{sup 2} was fabricated by rolling method using square billet as starting shape. The joining of the multifilamentary wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. (author). 66 refs., 104 figs.

Development of superconductor application technology

International Nuclear Information System (INIS)

Hong, G. W.; Kim, C. J.; Lee, H. G.; Lee, H. J.; Kim, K. B.; Won, D. Y.; Jang, K. I.; Kwon, S. C.; Kim, W. J.; Ji, Y. A.; Yang, S. W.; Kim, W. K.; Park, S. D.; Lee, M. H.; Lee, D. M.; Park, H. W.; Yu, J. K.; Lee, I. S.; Kim, J. J.; Choi, H. S.; Chu, Y.; Kim, Y. S.; Kim, D. H.

1997-09-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype flywheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies onthe method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting power with good reactivity and fine particle size was obtained by mechanical grinding, control of phase assemblage, and emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Jc of 20,000 A/cm 2 was fabricated by applying CIP packing procedure. Multifilamentary wire with Jc of 10,000 A/cm 2 was fabricated by rolling method using square billet as starting shape. The joining of the multifilamentary wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. (author). 66 refs., 104 figs

Bulk viscosity of spin-one color superconductors

Energy Technology Data Exchange (ETDEWEB)

Sa' d, Basil A.

2009-08-27

The bulk viscosity of several quark matter phases is calculated. It is found that the effect of color superconductivity is not trivial, it may suppress, or enhance the bulk viscosity depending on the critical temperature and the temperature at which the bulk viscosity is calculated. Also, is it found that the effect of neutrino-emitting Urca processes cannot be neglected in the consideration of the bulk viscosity of strange quark matter. The results for the bulk viscosity of strange quark matter are used to calculate the r-mode instability window of quark stars with several possible phases. It is shown that each possible phase has a different structure for the r-mode instability window. (orig.)

Bulk viscosity of spin-one color superconductors

International Nuclear Information System (INIS)

Sa'd, Basil A.

2009-01-01

The bulk viscosity of several quark matter phases is calculated. It is found that the effect of color superconductivity is not trivial, it may suppress, or enhance the bulk viscosity depending on the critical temperature and the temperature at which the bulk viscosity is calculated. Also, is it found that the effect of neutrino-emitting Urca processes cannot be neglected in the consideration of the bulk viscosity of strange quark matter. The results for the bulk viscosity of strange quark matter are used to calculate the r-mode instability window of quark stars with several possible phases. It is shown that each possible phase has a different structure for the r-mode instability window. (orig.)

Controlled levitation of Y-Ba-Cu-O bulk superconductors and energy minimum analysis; Y-Ba-Cu-O baruku chodendotai no fujo to enerugi kaiseki

Energy Technology Data Exchange (ETDEWEB)

Magashima, K. [Railway Technical Research Institute, Tokyo (Japan); Iwasa, Y. [Francis Bitter Magnet Laboratory, Canbridge (United States); Sawa, K. [keio University, Tokyo (Japan); Murakami, M. [Superconductivity research Laboratory, Tokyo (Japan)

1999-11-25

The levitation of bulk Y-Ba-Cu-O superconductors can be controlled using a Bi-Sr-Ca-Cu-O (Bi2223) superconducting electromagnet. It was found that stable levitation without tilting could be obtained only when the sample trapped a certain amount of fields, the minimum of which depended on the external field and sample dimensions. We employed a novel analysis method for levitation based on the total energy balance, which is much simpler than the force method and could be applied to understanding general levitation behavior. Numerical analyses thus developed showed that stable levitation of superconductors with large dimensions cen only be achieved when the induced currents can flow with three-dimensional freedom. (author)

High critical currents in heavily doped (Gd,Y)Ba{sub 2}Cu{sub 3}O{sub x} superconductor tapes

Energy Technology Data Exchange (ETDEWEB)

Selvamanickam, V., E-mail: selva@uh.edu; Gharahcheshmeh, M. Heydari; Xu, A.; Galstyan, E.; Delgado, L. [Department of Mechanical Engineering and Texas Center for Superconductivity, University of Houston, 4800 Calhoun Rd., Houston, Texas 77204-4006 (United States); Cantoni, C. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37381 (United States)

2015-01-19

REBa{sub 2}Cu{sub 3}O{sub x} ((REBCO), RE = rare earth) superconductor tapes with moderate levels of dopants have been optimized for high critical current density in low magnetic fields at 77 K, but they do not exhibit exemplary performance in conditions of interest for practical applications, i.e., temperatures less than 50 K and fields of 2–30 T. Heavy doping of REBCO tapes has been avoided by researchers thus far due to deterioration in properties. Here, we report achievement of critical current densities (J{sub c}) above 20 MA/cm{sup 2} at 30 K, 3 T in heavily doped (25 mol. % Zr-added) (Gd,Y)Ba{sub 2}Cu{sub 3}O{sub x} superconductor tapes, which is more than three times higher than the J{sub c} typically obtained in moderately doped tapes. Pinning force levels above 1000 GN/m{sup 3} have also been attained at 20 K. A composition map of lift factor in J{sub c} (ratio of J{sub c} at 30 K, 3 T to the J{sub c} at 77 K, 0 T) has been developed which reveals the optimum film composition to obtain lift factors above six, which is thrice the typical value. A highly c-axis aligned BaZrO{sub 3} (BZO) nanocolumn defect density of nearly 7 × 10{sup 11 }cm{sup −2} as well as 2–3 nm sized particles rich in Cu and Zr have been found in the high J{sub c} films.

Magnetism at the V/Gd interface

International Nuclear Information System (INIS)

Mouketo, L; M'Passi-Mabiala, B; Binggeli, N

2010-01-01

Recent experimental investigations into the magnetic properties of V/Gd bilayers have shown that vanadium, which is nonmagnetic in the bulk, can acquire a magnetic moment in such systems. We have performed ab initio pseudopotential calculations to examine the magnetic behavior of V(110)/Gd(0001) bilayers for V layers with thicknesses up to 4 monolayers (ML). We considered both abrupt and atomic intermixed V/Gd interfaces. In both cases, the magnetic moment of the V layer is found to align antiparallel to the moment of the Gd layer, consistent with the experimental observation. However, the magnitude of the V moment at the abrupt interface is considerably smaller than the moments reported experimentally. In the presence of atomic intermixing, instead, substantially larger V moments are found, closer to the experimentally reported moments. On the basis of the calculated atomic and spin resolved density of states, we discuss the possible mechanism responsible for the observed Gd-V antiferromagnetic coupling.

Luminescent GdVO{sub 4}:Sm{sup 3+} quantum dots enhance power conversion efficiency of bulk heterojunction polymer solar cells by Förster resonance energy transfer

Energy Technology Data Exchange (ETDEWEB)

Bishnoi, Swati [CSIR-Network of Institutes for Solar Energy, New Delhi 110001 (India); Luminescent Materials and Devices Group, CSIR-National Physical Laboratory, New Delhi 110012 (India); Academy of Scientific and Innovative Research (AcSIR), CSIR-National Physical Laboratory, Dr. K. S. Krishnan Marg, New Delhi 110012 (India); Gupta, Vinay, E-mail: drvinaygupta@netscape.net; Sharma, Gauri D.; Chand, Suresh [CSIR-Network of Institutes for Solar Energy, New Delhi 110001 (India); Organic and Hybrid Solar Cells Group, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, New Delhi 110012 (India); Sharma, Chhavi; Kumar, Mahesh [Ultrafast Optoelectronics and Terahertz Photonics Lab, Physics of Energy Harvesting Division, CSIR-National Physical Laboratory, New Delhi 110012 (India); Haranath, D. [CSIR-Network of Institutes for Solar Energy, New Delhi 110001 (India); Luminescent Materials and Devices Group, CSIR-National Physical Laboratory, New Delhi 110012 (India); Naqvi, Sheerin [Luminescent Materials and Devices Group, CSIR-National Physical Laboratory, New Delhi 110012 (India)

2016-07-11

In this work, we report enhanced power conversion efficiency (PCE) of bulk heterojunction polymer solar cells by Förster resonance energy transfer (FRET) from samarium-doped luminescent gadolinium orthovanadate (GdVO{sub 4}:Sm{sup 3+}) quantum dots (QDs) to polythieno[3,4-b]-thiophene-co-benzodithiophene (PTB7) polymer. The photoluminescence emission spectrum of GdVO{sub 4}:Sm{sup 3+} QDs overlaps with the absorption spectrum of PTB7, leading to FRET from GdVO{sub 4}:Sm{sup 3+} to PTB7, and significant enhancements in the charge-carrier density of excited and polaronic states of PTB7 are observed. This was confirmed by means of femtosecond transient absorption spectroscopy. The FRET from GdVO{sub 4}:Sm{sup 3+} QDs to PTB7 led to a remarkable increase in the power conversion efficiency (PCE) of PTB7:GdVO{sub 4}:Sm{sup 3+}:PC{sub 71}BM ([6,6]-phenyl-C{sub 71}-butyric acid methyl ester) polymer solar cells. The PCE in optimized ternary blend PTB7:GdVO{sub 4}:Sm{sup 3+}:PC{sub 71}BM (1:0.1:1.5) is increased to 8.8% from 7.2% in PTB7:PC{sub 71}BM. This work demonstrates the potential of rare-earth based luminescent QDs in enhancing the PCE of polymer solar cells.

Three-dimensional Majorana fermions in chiral superconductors.

Science.gov (United States)

Kozii, Vladyslav; Venderbos, Jörn W F; Fu, Liang

2016-12-01

Using a systematic symmetry and topology analysis, we establish that three-dimensional chiral superconductors with strong spin-orbit coupling and odd-parity pairing generically host low-energy nodal quasiparticles that are spin-nondegenerate and realize Majorana fermions in three dimensions. By examining all types of chiral Cooper pairs with total angular momentum J formed by Bloch electrons with angular momentum j in crystals, we obtain a comprehensive classification of gapless Majorana quasiparticles in terms of energy-momentum relation and location on the Fermi surface. We show that the existence of bulk Majorana fermions in the vicinity of spin-selective point nodes is rooted in the nonunitary nature of chiral pairing in spin-orbit-coupled superconductors. We address experimental signatures of Majorana fermions and find that the nuclear magnetic resonance spin relaxation rate is significantly suppressed for nuclear spins polarized along the nodal direction as a consequence of the spin-selective Majorana nature of nodal quasiparticles. Furthermore, Majorana nodes in the bulk have nontrivial topology and imply the presence of Majorana bound states on the surface, which form arcs in momentum space. We conclude by proposing the heavy fermion superconductor PrOs 4 Sb 12 and related materials as promising candidates for nonunitary chiral superconductors hosting three-dimensional Majorana fermions.

Fabrication and characterizations of the BSCCO-2212/SrSO4 bulk superconductors

International Nuclear Information System (INIS)

Kim, Kyu Tae; Jang, Seok Hern; Park, Eui Cheol; Hwang, Sumin; Joo, Jin Hoo; Hong, Gye Won; Kim, Chan Joong; Kim, Hye Rim; Hyun, Ok Bae

2006-01-01

We fabricated Bi-2212/SrSO 4 bulk superconductors by the casting process and evaluated the effects of the powder mixing method and annealing temperature on the texture, microstructure, and critical current. In the process, the Bi-2212 powders were mixed with SrSO 4 by hand-mixing(HM) and planetary ball milling(PBM) method and then the powder mixtures were melted at 1100 - 1200 degrees C, solidified, and annealed. We observed that the rod made by the PBM had a more homogeneous microstructure and smaller SrSO 4 and second phases than that of the rod made by the HM, resulting in increased I c . The I c of the rod also depended on the annealing temperature and the highest I c was obtained to be 200 A when prepared by HM at 1200 degrees C and annealed at 810 degrees C which is probably due to the moderate density and 2212 texture and the smaller and less second phase compared to that at higher temperature. The possible causes of the variations of I c with the powder mixing method and annealing temperature were related to the microstructural evolution based on the SEM, EPMA, and DTA analyses.

Processing Y- and Bi-based superconductors

International Nuclear Information System (INIS)

Balachandran, U.; Dos Santos, D.I.; von Stumberg, A.W.; Graham, S.W.; Singh, J.P.; Youngdahl, C.A.; Goretta, K.C.; Shi, D.; Poeppel, R.B.

1989-01-01

This paper reports on bulk specimens of YBa 2 Cu 3 O x and Bi 2 Sr 2 CaCu 2 O y formed and then processed by sintering in the solid state, in the presence of a liquid phase, or by sinter forging. Both Y- and Bi-based superconductors are difficult to densify by solid-state sintering but easy to densify in the presence of a liquid phase. Effects of sintering conditions on superconducting properties are, however, different between the two materials. These differences will be discussed. Attempts to texture microstructures and increase J c by sinter-forging techniques have been successful for Y-based superconductors, but unsuccessful for Bi-based superconductors

Coasting characteristic of the flywheel system under anisotropy effect of bulk high temperature superconductors

Science.gov (United States)

Wu, J. F.; Li, Y.

2014-10-01

High-temperature superconductors (HTSCs) array with aligned growth section boundary (GSB) pattern (AGSBP) exhibits larger levitation force and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP) has been studied in maglev train application (Zheng et al., 2013). This result maybe helpful and support a new way for the HTS bearing design for flywheel systems. So, in this paper, we further examine this growth anisotropy effect on the maglev performance of flywheel system. Levitation force and coasting time were investigated from the point-view of HTS flywheel applications. The GS/GSB alignment of AGSBP bulk HTSCs produces larger levitation force than that of MGSBP, but the coasting time is shorter than that of MGSBP, that is to say, the electric magnetic drag force with AGSBP is larger than that of MGSBP. This result may also exist in the maglev guideline when the maglev train stops freely.

Mechanical and Magnetic Properties of YBCO Superconductor with Bi/CNT Composite and Resin/CNT Impregnation

International Nuclear Information System (INIS)

Oh, W. S.; Jang, G. E.; Han, Y. H.; Sung, T. H.

2007-01-01

Bi/CNT composite and resin/CNT were chosen to improve the mechanical properties of YBa 2 Cu 3 O 7 (YBCO) superconductor. In order to elucidate the effects of Bi/CNT composite and resin/CNT in YBCO superconductors, melt texture superconductor were impregnated by mixed compound of Bi and CNT into the artificial holes parallel to the c-axis, which were drilled on the YBCO superconductor. Various amount of Bi/CNT and resin/CNT were impregnated to YBCO superconductor with different holes diameters. Typical artificial holes diameters were 0.5, 0.7, and 1.0 mm respectively. Result of three-point bending test measurement, the bending strength with resin/CNT impregnation was improved up to 59.64 MPa as compared with 50.79 MPa of resin/CNT free bulk. Resin/CNT impregnation has been found to be one of the effective ways in improving the mechanical properties of bulk superconductor.

Magnetic precipitate separation for Ni plating waste liquid using HTS bulk magnets

Science.gov (United States)

Oka, T.; Kimura, T.; Mimura, D.; Fukazawa, H.; Fukui, S.; Ogawa, J.; Sato, T.; Ooizumi, M.; Yokoyama, K.; Tsujimura, M.; Terasawa, T.

2013-01-01

The magnetic separation experiment for recycling the nickel-bearing precipitates in the waste liquid from the electroless plating processes has been practically conducted under the high gradient magnetic separation technique with use of the face-to-face HTS bulk magnet system. A couple of facing magnetic poles containing Sm123 bulk superconductors were activated through the pulsed field magnetization process to 1.86 T at 38 K and 2.00 T at 37 K, respectively. The weakly magnetized metallic precipitates of Ni crystals and Ni-P compounds deposited from the waste solution after heating it and pH controlling. The high gradient magnetic separation technique was employed with the separation channels filled with the stainless steel balls with dimension of 1 and 3 mm in diameter, which periodically moved between and out of the facing magnetic poles. The Ni-bearing precipitates were effectively attracted to the magnetized ferromagnetic balls. We have succeeded in obtaining the separation ratios over 90% under the flow rates less than 1.35 L/min.

Mechanical design of a synchronous rotating machines with Gd-Ba-Cu-O HTS bulk pole-field magnets operated by a pulsed-field magnetization with armature copper coils

Energy Technology Data Exchange (ETDEWEB)

Matsuzaki, H [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Kimura, Y [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Ohtani, I [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Morita, E [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Ogata, H [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Izumi, M [Department of Electronic and Mechanical Engineering, Tokyo University of Marine Science and Technology, Koto-ku, Tokyo 135-8533 (Japan); Ida, T [Department of Electronic Control Engineering, Hiroshima National College of Maritime Technology, Hiroshima 725-0231 (Japan); Sugimoto, H [Department of Electrical and Electronic Engineering, Fukui University, Fukui 910-8507 (Japan); Miki, M [Kitano Seiki Co. Ltd., Ohta-ku, Tokyo 143-0024 (Japan); Kitano, M [Kitano Seiki Co. Ltd., Ohta-ku, Tokyo 143-0024 (Japan)

2006-06-01

We studied a high-temperature superconducting (HTS) synchronous motor assembled with melt-textured Gd-Ba-Cu-O bulk pole-field magnets. The structure of a HTS motor is an axial gap type with neither brushes/slip rings nor iron core. The specific feature is that the rotor pole-field magnets of bulk are magnetized with pulsed current flow through vortex-type armature copper windings. The rotor pole bulks and armature coils are cooled down with liquid nitrogen. Cooling and magnetization of bulk pole field magnets are performed inside of the rotor. The trapped peak magnetic field of more than 0.5 T of the bulk magnets provided the motor performance of 3.1 kW with 720 rpm. In order to attain high output, single rotor plate with 8 bulks was substituted with a twinned rotor plates with 16 bulks together with triple layer armature units. We report on the test results and performance of the present twinned rotor-type HTS synchronous motor.

Bulk glass ceramics containing Yb{sup 3+}/Er{sup 3+}: β-NaGdF{sub 4} nanocrystals: Phase-separation-controlled crystallization, optical spectroscopy and upconverted temperature sensing behavior

Energy Technology Data Exchange (ETDEWEB)

Chen, Daqin, E-mail: dqchen@fjirsm.ac.cn [College of Materials & Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Wan, Zhongyi; Zhou, Yan [College of Materials & Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Huang, Ping, E-mail: phuang@fjirsm.ac.cn [Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China); Zhong, Jiasong; Ding, Mingye [College of Materials & Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Xiang, Weidong; Liang, Xiaojuan [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou 325035 (China); Ji, Zhenguo, E-mail: jizg@hdu.edu.cn [College of Materials & Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China)

2015-07-25

Highlights: • Hexagonal NaGdF{sub 4} nanocrystals embedded bulk glass ceramics were fabricated. • The incorporation of Ln{sup 3+} dopants into the β-NaGdF{sub 4} lattice was demonstrated. • Upconversion luminescence was highly intensified after glass crystallization. • Such glass ceramics had possible application in the optical temperature sensors. - Abstract: Lanthanide doped hexagonal β-NaGdF{sub 4} nanocrystals embedded transparent bulk glass ceramics were successfully fabricated via a phase-separation-controlled crystallization route. Elemental mapping in the scanning transmission electron microscope and optical spectroscopy analysis demonstrated the partition of the active centers into the β-NaGdF{sub 4} crystalline lattice. As a result, upconversion luminescence of the glass ceramic co-doped with Yb{sup 3+} and Er{sup 3+} is about 60 times as high as that of the precursor glass, attributing to the modification of Yb{sup 3+}/Er{sup 3+} surrounding from phase-separated amorphous nanoparticle to β-NaGdF{sub 4} crystalline lattice with low phonon energy and high crystallinity after crystallization. Furthermore, the temperature-dependent green upconversion emissions assigned to {sup 2}H{sub 11/2} → {sup 4}I{sub 15/2} (520 nm) and {sup 4}S{sub 3/2} → {sup 4}I{sub 15/2} (540 nm) transitions were investigated, and the corresponding fluorescence intensity ratio of these two thermally coupled emitting-states greatly enhanced with increase of temperature. Using such fabricated glass ceramic as an optical thermometric medium, the maximum sensitivity reached as high as 0.0037 K{sup −1} at 580 K. It is expected that the investigated Er{sup 3+}/Yb{sup 3+} codoped glass ceramic might be a very promising candidate for accurate optical temperature sensors.

Macroscopic theory of superconductors

International Nuclear Information System (INIS)

Carr, W.J. Jr.

1981-01-01

A macroscopic theory for bulk superconductors is developed in the framework of the theory for other magnetic materials, where ''magnetization'' current is separated from ''free'' current on the basis of scale. This contrasts with the usual separation into equilibrium and nonequilibrium currents. In the present approach magnetization, on a large macroscopic scale, results from the vortex current, while the Meissner current and other surface currents are surface contributions to the Maxwell j. The results are important for the development of thermodynamics in type-II superconductors. The advantage of the description developed here is that magnetization becomes a local concept and its associated magnetic field can be given physical meaning

Magnetic, electrical and structural properties of the Re-doped ruthenocuprate Ru1−xRexSr2GdCu2Oy

International Nuclear Information System (INIS)

Corredor, L.T.; Albino Aguiar, J.; Landínez Téllez, D.A.; Pureur, P.; Mesquita, F.; Roa-Rojas, J.

2015-01-01

Highlights: • We investigated the effect of the dilution of magnetic Ru sub-lattice of RuSr 2 GdCu 2 O 8 . • We synthesized the doped compound Rui x Re x Sr 2 GdCu 2 O y , for 3%, 6%, 9% and 12% Re. • Re would affect the electron coupling: just 3 and 6% samples were superconductor. • Superconductivity emergence strongly affects magnetic properties of 3 and 6% samples. • A weak ferromagnetic component is consistent with a globally antiferromagnetic system. - Abstract: Despite the discovery of new superconductors classes, high-Tc oxides continue to be a current topic, because of their complex phase diagrams and doping-dependant effects (allowing one to investigate the interaction between orbitals), as well as structural properties such as lattice distortion and charge ordering, among many others. Ruthenocuprates are magnetic superconductors in which the magnetic transition temperature is much higher than the critical superconducting temperature, making them unique compounds. With the aim of investigating the dilution of the magnetic Ru sub-lattice, we proposed the synthesis of the Ru 1−x Re x Sr 2 GdCu 2 O y ruthenocuprate-type family, adapting the known two-step process (double perovskite + CuO) by directly doping the double perovskite, thus obtaining the perovskite compound Sr 2 GdRu 1−x Re x O y , which represents a new synthesis process to the best of our knowledge. Our samples were structurally characterized through X-ray diffraction, and the patterns were analysed via Rietveld refinement. A complete magnetic characterization as a function of temperature and applied field, as well as transport measurements were carried out. We discuss our results in the light of the two-lattice model for ruthenocuprates, and a relation between RuO 2 (magnetic) and CuO 2 (superconductor) sub-lattices can clearly be observed

Study of the glass formation of high temperature superconductors

Science.gov (United States)

Ethridge, Edwin C.; Kaukler, William F.; Rolin, Terry

1992-01-01

A number of compositions of ceramic oxide high T(sub c) superconductors were elevated for their glass formation ability by means of rapid thermal analysis during quenching, optical, and electron microscopy of the quenched samples, and with subsequent DSC measurements. Correlations between experimental measurements and the methodical composition changes identified the formulations of superconductors that can easily form glass. The superconducting material was first formed as a glass; then, with subsequent devitrification, it was formed into a bulk crystalline superconductor by a series of processing methods.

Advanced technologies related to a high temperature superconductor for small laboratory experiments

International Nuclear Information System (INIS)

Ogawa, Yuichi; Mito, Toshiyuki; Yanagi, Nagato

2006-01-01

Advanced technologies related to a high temperature superconductor materials and small refrigerator are reviewed. Mini-RT/RT-1 is designed and constructed as a plasma examination device. The element technology of low temperature apparatus, the results of performance tests and application examples are explained. The superconductors such as Bi 2 Sr 2 CaCu 2 O 8 (Bi-2212) for the low temperature phase, Bi 2 Sr 2 Ca 2 Cu 3 O 10 (Bi-2223) for the high temperature phase, and YBa 2 Cu 3 O y (YBCO or Y123) are described. Advanced 4K-Giford-Mcmahon (GM) refrigerator on the market put superconductor coil made of low temperature superconductor metals to practical use and extends its application field. Small laboratory is able to experiment on the high temperature superconductor materials. (S.Y.)

The Effects of Gd-Free Impurity Phase on the Aging Behavior for the Microwave Surface Resistance of Ag-coated GdBa2Cu3O7-δ at Cryogenic Temperatures

Science.gov (United States)

Lee, Sungho; Yang, Woo Il; Jung, Ho Sang; Oh, Won-Jae; Jang, Jiyeong; Lee, Jae-Hun; Kang, Kihyeok; Moon, Seung-Hyun; Yoo, Sang-Im; Lee, Sang Young

2018-05-01

High-T C GdBa2Cu3O7-δ (GdBCO) superconductor has been popular for making superconductive tapes that have much potential for various fields of large-scale applications. We investigated aging effects on the microwave surface resistance (R S) of Ag-coated GdBCO layer on Hastelloy substrate, so called GdBCO coated conductors (CCs), and Ag-coated GdBCO films on LaAlO3 (LAO) single-crystal substrates at cryogenic temperatures and compared them with each other. Unlike the R S of Ag-coated GdBCO films showing significant degradation in 4 weeks, no significant aging effects were found in our Ag-coated GdBCO CCs aged 85 weeks. The reactive co-evaporation deposition and reaction (RCE-DR) method was used for preparing the Ag-coated GdBCO CCs. Such durability of the Ag-coated GdBCO CCs in terms of the R S could be explained by existence of a protective impurity phase, i.e., Gd-free Ba-Cu-O phase as confirmed by transmission electron microscopy study combined with the energy-dispersive X-ray spectroscopy measurements. Although the scope of this study is limited to the Ag-coated GdBCO CCs prepared by using the RCE-DR method, our results suggest that a solution for preventing the aging effects on transport properties of other kinds of Ag-coated GdBCO CCs could be realized by means of an artificially-grown protective impurity layer.

Magnetic properties of GdMnO3 nanoparticles embedded in mesoporous silica

Science.gov (United States)

Tajiri, Takayuki; Mito, Masaki; Deguchi, Hiroyuki; Kohno, Atsushi

2018-05-01

Perovskite manganite GdMnO3 nanoparticles were synthesized using mesoporous silica as a template, and their magnetic properties and crystal structure were investigated. Powder X-ray diffraction data indicated successful synthesis of the GdMnO3 nanoparticles, with mean particle sizes of 13.9 and 20.9 nm. The lattice constants for the nanoparticles were slightly different from those for the bulk material and varied with the particle size. The magnetic transition temperatures for the nanoparticles were higher than those of the bulk crystal. The synthesized GdMnO3 nanoparticles exhibited superparamagnetic behaviors: The blocking temperature, coercive field, and transition temperature depended on the particle size. Magnetic measurements and crystal structure analysis suggest that the changes in the magnetic properties for GdMnO3 nanoparticles can be attributed to the modulation of the crystallographic structure.

Angular correlation and lifetime measurements in /sup 154/Gd

Energy Technology Data Exchange (ETDEWEB)

Sharma, A K; Verma, H R; Kaur, R; Sooch, S S; Trehan, P N

1982-03-01

Multipole admixtures in 591.80, 692.51, 723.38, 756.84, 873.27, 1004.74, 1274.50, 1494.22 and 1596.65 keV transitions have been measured by investigating nine gamma-gamma angular correlations in /sup 154/Gd. The present study confirms very small Ml admixtures in the transitions from ..beta..- and ..gamma..-vibrational bands to ground state band in /sup 154/Gd which is a transitional nucleus. In addition, lifetime of an excited level at 123.04 keV has been measured to be 1.19 +- 0.03 nsec.

Melt-processed LRE-Ba-Cu-O superconductors and prospects for their applications

International Nuclear Information System (INIS)

Yoo, S.I.; Fujimoto, H.; Sakai, N.; Murakami, M.

1997-01-01

We have recently found that control of the oxygen partial pressure (PO 2 ) during melt processing, named the oxygen-controlled melt-growth (OCMG) process, is critical for obtaining a high superconducting transition temperature (T c ) in the light rare earth (LRE)-Ba-Cu-O (LREBCO) superconductors particularly for Nd, Sm and Eu. Further, compared to a good melt-processed Y-Ba-Cu-O (YBCO) bulk superconductor, LREBCO bulks exhibit larger critical current density (J c ) in high magnetic field and a much improved irreversibility field (H irr ) at 77 K, implying that more effective flux pinning can be realized in a commercially feasible way. In this paper, properties and characteristic flux pinning of OCMG-processed LREBCO (LRE: Nd,Sm,Eu) superconductors are described on the basis of our study during the last several years. We also present the prospects for bulk-type applications, such as the magnetic bearings, flywheels and magnetically levitated (MAGLEV) trains. (orig.)

Magnetic precipitate separation for Ni plating waste liquid using HTS bulk magnets

Energy Technology Data Exchange (ETDEWEB)

Oka, T., E-mail: okat@eng.niigata-u.ac.jp [Niigata University, 8050 Ikarashi-Ninocho, Nishi-ku, Niigata 950-2181 (Japan); Kimura, T.; Mimura, D.; Fukazawa, H.; Fukui, S.; Ogawa, J.; Sato, T.; Ooizumi, M. [Niigata University, 8050 Ikarashi-Ninocho, Nishi-ku, Niigata 950-2181 (Japan); Yokoyama, K. [Ashikaga Institute of Technology, 268-1 Ohmae-cho, Ashikaga, Tochigi 326-8558 (Japan); Tsujimura, M. [Aichi Giken Co., 2-1-47 Shiobaru, Minami-ku, Fukuoka 815-8520 (Japan); Terasawa, T. [IMRA Material R and D Co., Ltd., 2-1 Asahimachi, Kariya, Aichi 448-0032 (Japan)

2013-01-15

Highlights: ► The magnetic separation was operated for recycling the electroless plating waste. ► The HTS bulk magnet effectively attracted the ferromagnetic precipitates with Ni. ► The separation ratios over 90% were reported under flow rates up to 1.35 L/min. -- Abstract: The magnetic separation experiment for recycling the nickel-bearing precipitates in the waste liquid from the electroless plating processes has been practically conducted under the high gradient magnetic separation technique with use of the face-to-face HTS bulk magnet system. A couple of facing magnetic poles containing Sm123 bulk superconductors were activated through the pulsed field magnetization process to 1.86 T at 38 K and 2.00 T at 37 K, respectively. The weakly magnetized metallic precipitates of Ni crystals and Ni–P compounds deposited from the waste solution after heating it and pH controlling. The high gradient magnetic separation technique was employed with the separation channels filled with the stainless steel balls with dimension of 1 and 3 mm in diameter, which periodically moved between and out of the facing magnetic poles. The Ni-bearing precipitates were effectively attracted to the magnetized ferromagnetic balls. We have succeeded in obtaining the separation ratios over 90% under the flow rates less than 1.35 L/min.

Investigation of nanocrystalline Gd films loaded with hydrogen

KAUST Repository

Hruška, Petr; Čí žek, Jakub; Dobroň, Patrik; Anwand, Wolfgang; Mü cklich, Arndt; Gemma, Ryota; Wagner, Stefan; Uchida, Helmut; Pundt, Astrid

2015-01-01

The present work reports on microstructure studies of hydrogen-loaded nanocrystalline Gd films prepared by cold cathode beam sputtering on sapphire (112¯0) substrates. The Gd films were electrochemically step-by-step charged with hydrogen and the structural development with increasing concentration of absorbed hydrogen was studied by transmission electron microscopy and in-situ   X-ray diffraction using synchrotron radiation. The relaxation of hydrogen-induced stresses was examined by acoustic emission measurements. In the low concentration range absorbed hydrogen occupies preferentially vacancy-like defects at GBs typical for nanocrystalline films. With increasing hydrogen concentration hydrogen starts to occupy interstitial sites. At the solid solution limit the grains gradually transform into the ββ-phase (GdH2). Finally at high hydrogen concentrations xH>2.0xH>2.0 H/Gd, the film structure becomes almost completely amorphous. Contrary to bulk Gd specimens, the formation of the γγ-phase (GdH3) was not observed in this work.

Optimization of a condensed-neon cooling system for a HTS synchronous motor with Gd-bulk HTS field-pole magnets

Energy Technology Data Exchange (ETDEWEB)

Felder, B; Miki, M; Tsuzuki, K; Izumi, M [Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, 2-1-6, Etchujima, Koto-ku, Tokyo 135-8533 (Japan); Hayakawa, H, E-mail: d082028@kaiyodai.ac.j [Kitano Seiki Co. Ltd., 7-17-3, Chuo, Ota-ku, Tokyo 143-0024 (Japan)

2010-06-01

The axial-gap synchronous machine developed in our laboratory is based on Gd-bulk HTS field-pole magnets, able to trap a part of the magnetic flux they are submitted to when cooled down below T{sub c}. At the liquid nitrogen temperature, by the Pulsed-Field Magnetization (PFM), 1.04 T was trapped in 60 mm-diameter and 20 mm-thickness magnets, leading to an output power of the motor of 10 kW at 720 rpm. To enhance this performance, we have to increase the total amount of trapped flux in the bulk, the shortest way being to decrease the temperature of the bulk HTS. Thus, we focused on the improvement of the condensed-neon cooling system, a closed-cycle thermosyphon, so that it provided enough cooling power to lead the rotor plate enclosing the magnets to a low temperature. The present study implied coming out with a new fin-oriented design of the condensation chamber; hence, the numeric calculations and FEM software (ANSYS) heat transfer simulations were conducted for various shapes and positions of the fins. The trapezoidal design offering the best efficiency was then manufactured for testing in a heat-load test configuration, leading to cooling times divided by three and a maximum heat load endured of 55 W.

Optimization of a condensed-neon cooling system for a HTS synchronous motor with Gd-bulk HTS field-pole magnets

Science.gov (United States)

Felder, B.; Miki, M.; Tsuzuki, K.; Izumi, M.; Hayakawa, H.

2010-06-01

The axial-gap synchronous machine developed in our laboratory is based on Gd-bulk HTS field-pole magnets, able to trap a part of the magnetic flux they are submitted to when cooled down below Tc. At the liquid nitrogen temperature, by the Pulsed-Field Magnetization (PFM), 1.04 T was trapped in 60 mm-diameter and 20 mm-thickness magnets, leading to an output power of the motor of 10 kW at 720 rpm. To enhance this performance, we have to increase the total amount of trapped flux in the bulk, the shortest way being to decrease the temperature of the bulk HTS. Thus, we focused on the improvement of the condensed-neon cooling system, a closed-cycle thermosyphon, so that it provided enough cooling power to lead the rotor plate enclosing the magnets to a low temperature. The present study implied coming out with a new fin-oriented design of the condensation chamber; hence, the numeric calculations and FEM software (ANSYS) heat transfer simulations were conducted for various shapes and positions of the fins. The trapezoidal design offering the best efficiency was then manufactured for testing in a heat-load test configuration, leading to cooling times divided by three and a maximum heat load endured of 55 W.

Order parameter effect critical fields and current of Y1–xPrx:123 superconductors

Directory of Open Access Journals (Sweden)

Sedky A.

2018-03-01

Full Text Available Fluctuation induced conductivity by Pr substitution at Y sites of Y1-xPrx:123 superconductors is reported. It is found that the mean field temperature Tcmf, deduced from the peak of dρ/dT versus T plot, gradually decreases by increasing Pr up to 0.40. The order parameter dimensionality (OPD is estimated from the slope of the logarithmic plot between excess conductivity Δσ and reduced temperature є. Interestingly, the crossover from 2D to 3D is obtained for samples with Pr = 0.00, 0.10 and 0.20, while with increasing Pr up to 0.40, the crossover from 0D to quasi-2D is obtained. On the other hand, the calculated values of interlayer coupling, coherence lengths, critical fields and critical current decrease with increasing Pr up to 0.20, but with the further increase of Pr, up to 0.40, they increase. The hole carriers/Cu ions anisotropy and G-L parameter gradually increase with Pr up to 0.40. Our results are discussed in terms of the effects of Pr substitution at Y site, such as oxygen rearrangements, anisotropy, hybridization and localization of holes in the overdoped region.

Topological Superconductivity on the Surface of Fe-Based Superconductors.

Science.gov (United States)

Xu, Gang; Lian, Biao; Tang, Peizhe; Qi, Xiao-Liang; Zhang, Shou-Cheng

2016-07-22

As one of the simplest systems for realizing Majorana fermions, the topological superconductor plays an important role in both condensed matter physics and quantum computations. Based on ab initio calculations and the analysis of an effective 8-band model with superconducting pairing, we demonstrate that the three-dimensional extended s-wave Fe-based superconductors such as Fe_{1+y}Se_{0.5}Te_{0.5} have a metallic topologically nontrivial band structure, and exhibit a normal-topological-normal superconductivity phase transition on the (001) surface by tuning the bulk carrier doping level. In the topological superconductivity (TSC) phase, a Majorana zero mode is trapped at the end of a magnetic vortex line. We further show that the surface TSC phase only exists up to a certain bulk pairing gap, and there is a normal-topological phase transition driven by the temperature, which has not been discussed before. These results pave an effective way to realize the TSC and Majorana fermions in a large class of superconductors.

Chemical pressure induced change in multiferroicity of Bi{sub 1+2x}Gd{sub 2x/2}Fe{sub 1−2x}O{sub 3} bulk ceramics

Energy Technology Data Exchange (ETDEWEB)

Pradhan, S.K. [Institute of Materials Science, Bhubaneswar 751013 Odisha (India); Center for Materials Research, Norfolk State University, Norfolk (United States); Sahu, D.R., E-mail: diptirs@yahoo.com [Institute of Materials Science, Bhubaneswar 751013 Odisha (India); Department of Natural and Applied Science, Namibia University of Science and Technology, Windhoek (Namibia); Rout, P.P.; Das, S.K. [Institute of Materials Science, Bhubaneswar 751013 Odisha (India); Pradhan, A.K. [Center for Materials Research, Norfolk State University, Norfolk (United States); Srinivasu, V.V. [Department of Physics, University of South Africa (South Africa); Roul, B.K., E-mail: ims@iopb.res.in [Institute of Materials Science, Bhubaneswar 751013 Odisha (India)

2017-04-01

We have optimized Gd ion substitution in BiFeO{sub 3} (BFO) and observed prominently change in structural, electrical and magnetic behavior of Bi{sub 1+2x}Gd{sub 2x/2}Fe{sub 1−2x}O{sub 3} ceramics synthesized through slow step sintering schedule. It is observed that with the increase in concentration of Gd (x=0.1), original structure of BFO is transformed from rhombohedral R3c space group to orthorhombic Pn21a space group. Surprisingly, unit cell volume is drastically contracted (35% for x=0.2) and the sintered specimen showed enhanced room temperature ferromagnetic behavior although the original BFO is normally G-type antiferromagnetic in nature at 643 K. It is expected that intrinsic chemical pressure within the bulk body built by the substitution of Gd in presence of excess bismuth greatly supported through unidirectional movement of electrical dipole moment with in each individual domain as a result of which suppression of leakage current with enhanced dielectric and ferroelectric hysteresis is observed.

Collection of Ni-bearing material from electroless plating waste by magnetic separation with HTS bulk magnet

International Nuclear Information System (INIS)

Oka, T.; Fukazawa, H.; Fukui, S.; Ogawa, J.; Sato, T.; Ooizumi, M.; Tsujimura, M.; Yokoyama, K.

2014-01-01

Highlights: ► The magnetic separation for Ni compounds was conducted by HTS bulk magnet. ► The coarse Ni-sulfate crystals were formed from the Ni-phosphite precipitates. ► Ni-sulfate crystals was separated from the mixture of Ni-sulfate and Ni-phosphite compounds. -- Abstract: The magnetic separation experiment to collect the Ni compounds from the waste liquid of electroless plating processes was conducted in the open-gradient magnetic separation process with the high temperature superconducting bulk magnet system. The magnetic pole containing Gd-based bulk superconductors was activated to 3.45 T at 35 K in the static magnetic field of 5 T with use of a superconducting solenoid magnet. The coarse Ni-sulfate crystals were formed by adding the concentrated sulfuric acid to the Ni-phosphite precipitates which yielded from the plating waste liquid by controlling the temperature and the pH value. The open-gradient magnetic separation technique was employed to separate the Ni-sulfate crystals from the mixture of the Ni-sulfate and Ni-phosphite compounds by the difference between their magnetic properties. And we succeeded in collecting Ni-sulfate crystals preferentially to the Ni-phosphite by attracting them to the magnetic pole soon after the Ni-sulfate crystals began to grow

Collection of Ni-bearing material from electroless plating waste by magnetic separation with HTS bulk magnet

Energy Technology Data Exchange (ETDEWEB)

Oka, T., E-mail: okat@eng.niigata-u.ac.jp [Niigata University, 8050 Ikarashi-Ninocho, Nishi-ku, Niigata 950-2181 (Japan); Fukazawa, H.; Fukui, S.; Ogawa, J.; Sato, T.; Ooizumi, M. [Niigata University, 8050 Ikarashi-Ninocho, Nishi-ku, Niigata 950-2181 (Japan); Tsujimura, M. [Aichi Giken Co., 50-1 Takeshita, Hitotugi-cho, Kariya, Aichi 448-0003 (Japan); Yokoyama, K. [Ashikaga Institute of Technology, 268-1 Ohmae-cho, Ashikaga, Tochigi 326-8558 (Japan)

2014-01-15

Highlights: ► The magnetic separation for Ni compounds was conducted by HTS bulk magnet. ► The coarse Ni-sulfate crystals were formed from the Ni-phosphite precipitates. ► Ni-sulfate crystals was separated from the mixture of Ni-sulfate and Ni-phosphite compounds. -- Abstract: The magnetic separation experiment to collect the Ni compounds from the waste liquid of electroless plating processes was conducted in the open-gradient magnetic separation process with the high temperature superconducting bulk magnet system. The magnetic pole containing Gd-based bulk superconductors was activated to 3.45 T at 35 K in the static magnetic field of 5 T with use of a superconducting solenoid magnet. The coarse Ni-sulfate crystals were formed by adding the concentrated sulfuric acid to the Ni-phosphite precipitates which yielded from the plating waste liquid by controlling the temperature and the pH value. The open-gradient magnetic separation technique was employed to separate the Ni-sulfate crystals from the mixture of the Ni-sulfate and Ni-phosphite compounds by the difference between their magnetic properties. And we succeeded in collecting Ni-sulfate crystals preferentially to the Ni-phosphite by attracting them to the magnetic pole soon after the Ni-sulfate crystals began to grow.

Study of the magnetic field distribution in high-temperature superconductors using muon-spin-rotation

International Nuclear Information System (INIS)

Zimmermann, P.R.

1994-01-01

Detailed and systematic μ + SR experiments have been performed in order to (i) investigate the temperature dependence of the magnetic penetration depth in various cuprate high-T c superconductors and (ii) study the vortex structures and dynamics in the highly anisotropic Bi 2 Sr 2 CaCu 2 O 8 . The μ + SR method and its application to superconductivity has been discussed. The positive muon is a microscopic probe of the local magnetic field in the bulk of a sample. The μ + SR technique can therefore measure the magnetic field distribution p(B) which is determined by the flux structure in the superconductor. The second moment (ΔB 2 ) of p(B) is closely related to the magnetic penetration depth λ, a fundamental parameter of superconductivity. It has been shown that in high-quality sintered samples a good estimate of the in-plane penetration depth λ ab can be given in terms of the muon-depolarization rate σ. Since the penetration depth is related to the superconducting order parameter, the temperature dependence of the penetration depth is a potential probe of the pairing state. Systematic measurements of the temperature dependence of σ have been performed in sintered samples of high quality in various members of the Y123 family, Pb and Y doped Tl1212 family, and also in Y124 and Bi2212. It is found that the extracted temperature behaviour of λ ab -2 is characteristic of each compound. This can be interpreted as a varying coupling strength in these systems. In well oxygenated Y123, λ ab -2 (T) is well described by the two-fluid model indicating strong coupling. The rest of the cuprates investigated show a λ ab -2 (T) which points to weaker coupling, with λ ab -2 (T) of highly oxygen deficient Y123 being similar to the weak-coupling BCS prediction. In the Y123 family the decreasing coupling strength with decreasing oxygen content is related to the increasing anisotropy. Comparison with theoretical predictions of λ ab -2 (T) revealed that the observed

Trapped magnetic field of a superconducting bulk magnet in high- Tc RE-Ba-Cu-O

International Nuclear Information System (INIS)

Fujimoto, Hiroyuki; Yoo, Sang Im; Higuchi, Takamitsu; Nakamura, Yuichi; Kamijo, Hiroki; Nagashima, Ken; Murakami, Masato

1999-01-01

Superconducting magnets made of high-T c superconductors are promising for industrial applications. It is well known that REBa 2 Cu 3 O 7-x and LRE (light rare-earth) Ba 2 Cu 3 O 7-x superconductors prepared by melt processes have a high critical current density, J c , at 77 K and high magnetic fields. Therefore, the materials are very prospective for high magnetic field application as a superconducting permanent/bulk magnet with liquid-nitrogen refrigeration. LREBaCuO bulks, compared with REBaCuO bulks, exhibit a larger J c in high magnetic fields and a much improved irreversibility field, H irr , at 77 K. In this study, we discuss the possibility and trapped field properties of a superconducting bulk magnet, as well as the melt processing for bulk superconductors and their characteristic superconducting properties. One of the applications is a superconducting magnet for the future magnetically levitated (Maglev) train

Holographic superconductor in the analytic hairy black hole

International Nuclear Information System (INIS)

Myung, Yun Soo; Park, Chanyong

2011-01-01

We study the charged black hole of hyperbolic horizon with scalar hair (charged Martinez-Troncoso-Zanelli: CMTZ black hole) as a model of analytic hairy black hole for holographic superconductor. For this purpose, we investigate the second order phase transition between CMTZ and hyperbolic Reissner-Nordstroem-AdS (HRNAdS) black holes. However, this transition unlikely occurs. As an analytic treatment for holographic superconductor, we develop superconductor in the bulk and superfluidity on the boundary using the CMTZ black hole below the critical temperature. The presence of charge destroys the condensates around the zero temperature, which is in accord with the thermodynamic analysis of the CMTZ black hole.

Nanoindentation study on Gd-deposited YBaCuO superconductor

Indian Academy of Sciences (India)

strength, fracture toughness, hardness (H) and reduced mod- ulus (Er) as well as .... several approaches based on elastic recovery, energy balance, strain gradient ... lower load than W for Y123 sample, the loading and unload- ing curves are ...

Open questions in the magnetic behaviour of high-temperature superconductors

International Nuclear Information System (INIS)

Cohen, L.F.; Jensen, Henrik Jeldtoft

1997-01-01

A principally experimental review of vortex behaviour in high-temperature superconductors is presented. The reader is first introduced to the basic concepts needed to understand the magnetic properties of type II superconductors. The concepts of vortex melting, the vortex glass, vortex creep, etc are also discussed briefly. The bulk part of the review relates the theoretical predictions proposed for the vortex system in high temperature superconductors to experimental findings. The review ends with an attempt to direct the reader to those areas which still require further clarification. (author)

Magnetic characterisation of large grain, bulk Y–Ba–Cu–O superconductor–soft ferromagnetic alloy hybrid structures

International Nuclear Information System (INIS)

Philippe, M.P.; Fagnard, J.-F.; Kirsch, S.; Xu, Z.; Dennis, A.R.; Shi, Y.-H.; Cardwell, D.A.; Vanderheyden, B.; Vanderbemden, P.

2014-01-01

Highlights: • Large grain, bulk YBaCuO superconductor (SC) combined with ferromagnetic elements. • The flux lines curve outwards through the ferromagnet in the remanent state. • The trapped field in the SC is enhanced by the presence of the ferromagnet. • The effects of the SC and the ferromagnet add when the ferromagnet is saturated. - Abstract: Large grain, bulk Y–Ba–Cu–O (YBCO) high temperature superconductors (HTS) have significant potential for use in a variety of practical applications that incorporate powerful quasi-permanent magnets. In the present work, we investigate how the trapped field of such magnets can be improved by combining bulk YBCO with a soft FeNi, ferromagnetic alloy. This involves machining the alloy into components of various shapes, such as cylinders and rings, which are attached subsequently to the top surface of a solid, bulk HTS cylinder. The effect of these modifications on the magnetic hysteresis curve and trapped field of the bulk superconductor at 77 K are then studied using pick-up coil and Hall probe measurements. The experimental data are compared to finite element modelling of the magnetic flux distribution using Campbell’s algorithm. Initially we establish the validity of the technique involving pick-up coils wrapped around the bulk superconductor to obtain its magnetic hysteresis curve in a non-destructive way and highlight the difference between the measured signal and the true magnetization of the sample. We then consider the properties of hybrid ferromagnet/superconductor (F/S) structures. Hall probe measurements, together with the results of the model, establish that flux lines curve outwards through the ferromagnet, which acts, effectively, like a magnetic short circuit. Magnetic hysteresis curves show that the effects of the superconductor and the ferromagnet simply add when the ferromagnet is saturated fully by the applied field. The trapped field of the hybrid structure is always larger than that of the

The enhancement of critical current density on the bulk of BPSCCO-system superconductor with silver additions

International Nuclear Information System (INIS)

Engkir Sukirman; Wisnu Ari Adi; Puji Sulisworo dan W Prasuad

1999-01-01

The influence of silver additions on the critical current density (Jc) of BPSCCO-bulk superconductor was investigated, with the aim of getting an increase of its Jc and trying to find out a correlation of Jc and structures of BPSCCO-silver composites. The BPSCCO-system superconductors with nominal composition Bi 1.84 Pb 0.34 Sr 2.00 Ca 2.03 Cu 3.06 O x (2223-phase) were synthesized by using solid state reaction method. The silver added was in the powder-AgO form varied from 0 to 30 wt % AgO. The critical current density, crystal structure, and micro-structure of BPSCCO-silver composites were characterized by means of four-point probe, x-ray diffractometer, and scanning electron microscope that is equipped with a link system energy dispersive spectrometer. It was found that silver additions to BPSCCO cause a reasonable improvement in Jc from 120 to 215 A/cm 2 , and a slight increase in Tc from 92 to 108 K, and lattice parameters of the 2223-phase from a 3.811(3) to 3.820(2) A, and from c = 37.08(3) to 37.15(2) A, with the optimum value occurs at 20 wt % AgO. The AgO powders added to the BPSCCO specimens were converted to Ag 2 O and metallic Ag during the annealing process at 827degC for 96 h in air. The addition of AgO to BPSCCO system does not necessarily lead to decomposition of the 2223-phase. The AgO reacts with and suppresses the 2201-phase. (author)

Magnetic transition in Co/(Gd-Co) multilayers

International Nuclear Information System (INIS)

Svalov, A.V.; Fernandez, A.; Barandiaran, J.M.; Vas'kovskiy, V.O.; Orue, I.; Tejedor, M.; Kurlyandskaya, G.V.

2008-01-01

[Co/Gd 0.36 Co 0.64 ] 4 /Co multilayers with Co termination layer have been prepared by rf sputtering. They form macroscopic ferrimagnets with a compensation temperature (T comp ) determined by the thickness ratio of the layers. In low fields the magnetization of Co and Gd-Co layers are along the axis of the applied field. Increasing field makes the moments of both the Co and Gd-Co layers deviate from the axis of the field giving rise to a transition into a twisted state. These magnetic transitions were studied by vibrating sample magnetometer (VSM), magneto-optic Kerr effect and magnetoresistance measurements at various temperatures. The nucleation and evolution of surface- and bulk-twisted magnetic states were also observed in these multilayers

2D-ACAR spectra of insulating and superconducting Y-123

International Nuclear Information System (INIS)

Smedskjaer, L.C.; Bansil, A.

1992-09-01

An overview of the two-dimensional angular correlation (2D-ACAR) positron annihilation results for the three fundamental phases of YBa 2 Cu 3 O x , namely, the normal metal, the superconductor, and the insulator, is presented. In addition to the c-axis projected momentum density, the recent results for the a-axis projection as well as the insulating Y123 are discussed. The experimental results are compared and contrasted with the corresponding band theory predictions as far as possible in order to gain insight into the electronic structure and Fermiology of this archetypal high-T c superconductor

Quantum information aspects on bulk and nano interacting Fermi system: A spin-space density matrix approach

Energy Technology Data Exchange (ETDEWEB)

Afzali, R., E-mail: afzali@kntu.ac.ir [Department of Physics, K. N. Toosi University of Technology, Tehran, 15418 (Iran, Islamic Republic of); Ebrahimian, N., E-mail: n.ebrahimian@shahed.ac.ir [Department of Physics, Faculty of Basic Sciences, Shahed University, Tehran, 18155-159 (Iran, Islamic Republic of); Eghbalifar, B., E-mail: b.eghbali2011@yahoo.com [Department of Agricultural Management, Marvdasht Branch, Azad University, Marvdasht (Iran, Islamic Republic of)

2016-10-07

Highlights: • In contrast to a s-wave superconductor, the quantum correlation of the d-wave superconductor is sensitive to the change of the gap magnitude. • Quantum discord of the d-wave superconductor oscillates. • Quantum discord becomes zero at a characteristic length of the d-wave superconductor. • Quantum correlation strongly depends on the length of grain. Length of the superconductor lower, the quantum correlation length higher. • Quantum tripartite entanglement for a nano-scale d-wave superconductor is better than for a bulk d-wave superconductor. - Abstract: By approximating the energy gap, entering nano-size effect via gap fluctuation and calculating the Green's functions and the space-spin density matrix, the dependence of quantum correlation (entanglement, discord and tripartite entanglement) on the relative distance of two electron spins forming Cooper pairs, the energy gap and the length of bulk and nano interacting Fermi system (a nodal d-wave superconductor) is determined. In contrast to a s-wave superconductor, quantum correlation of the system is sensitive to the change of the gap magnitude and strongly depends on the length of the grain. Also, quantum discord oscillates. Furthermore, the entanglement length and the correlation length are investigated. Discord becomes zero at a characteristic length of the d-wave superconductor.

Properties of Y Ba2 Cu3 O7-δ-Ag superconductors prepared by the citrate method

International Nuclear Information System (INIS)

Fonseca, F.C.; Muccillo, R.

1996-01-01

Y Ba 2 Cu 3 O 7-δ (123) ceramic superconductor and YBa 2 Cu 3 O 7-δ - Ag composite superconductors have been prepared by the citrate method. Microstructural analysis has been done by X-ray diffractometry and optical ceramography. The superconducting behaviour has been studied by 4-probe dc resistivity in the 77 K - 140 K temperature range. Silver percolation in the ceramic matrix was studied by electrical resistivity measurements at room temperature; the percolation threshold was found to be approximately 25 vol% (35.5 wt%) Ag. Specimens with silver addition showed improvement in the flexural strength of the 123 compound. The main results show that the critical temperature does not depend on the silver content in the composite specimens, and that approximately 3 wt% (1.8 vol%) Ag doping yields an optimized composite superconductor from the microstructural point of view, with platelet-like grain shapes. (author)

Quaternary borocarbides: New class of intermetallic superconductors

Science.gov (United States)

Nagarajan, R.; Gupta, L. C.; Dhar, S. K.; Mazumdar, Chandan; Hossain, Zakir; Godart, C.; Levy-Clement, C.; Padalia, B. D.; Vijayaraghavan, R.

1995-01-01

Our recent discovery of superconductivity (SC) in the four-element multiphase Y-Ni-B-C system at an elevated temperature (TC approximately 12 K) has opened up great possibilities of identifying new superconducting materials and generating new physics. Superconductivity with Tc (greater than 20 K) higher than that known so far in bulk intermetallics has been observed in multiphase Y-Pd-B-C and Th-Pd-B-C systems and a family of single phase materials RENi2B2C (RE= Y, rare earth) have been found. Our investigations show YNi2B2C to be a strong coupling hard type-II SC. HC2(T) exhibits an unconventional temperature dependence. Specific heat and magnetization studies reveal coexistence of SC and magnetism in RNi2B2C (R = Ho, Er, Tm) with magnetic ordering temperatures (Tc approximately 8 K, 10.5 K, 11 K and Tm approximately 5 K, approximately 7K, approximately 4 K respectively) that are remarkably higher than those in known magnetic superconductors . Mu-SR studies suggest the possibility of Ni atoms carrying a moment in TmNi2B2C. Resistivity results suggests a double re-entrant transition (SC-normal-SC) in HoNi2B2C. RENi2B2C (RE = Ce, Nd, Gd) do not show SC down to 4.2 K. The Nd- and Gd-compounds order magnetically at approximately 4.5 K and approximately 19.5 K, respectively. Two SC transitions are observed in Y-Pd-B-C (Tc approximately 22 K, approximately 10 K) and in Th-Pd-B-C (Tc approximately 20 K, approximately 14 K) systems, which indicate that there are at least two structures which support SC in these borocarbides. In our multiphase ThNi2B2C we observe SC at approximately 6 K. No SC was seen in multiphase UNi2B2C, UPd2B2C, UOs2Ge2C and UPd5B3C(0.35) down to 4.2 K. Tc in YNi2B2C is depressed by substitutions (Gd, Th and U at Y-sites and Fe, Co at Ni-sites).

Superconductor bearings, flywheels and transportation

International Nuclear Information System (INIS)

Werfel, F N; Floegel-Delor, U; Rothfeld, R; Riedel, T; Goebel, B; Wippich, D; Schirrmeister, P

2012-01-01

This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN 2 . More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

Ceramic high temperature superconductors for high current applications

Energy Technology Data Exchange (ETDEWEB)

Christiansen, J.

1996-12-31

Composite Reaction Texturing (CRT) is a technique which uses a fine distribution of pre-aligned seeds as nucleating sites for texturing oxide superconductors. It has successfully been applied to the texturing of Bi-2212 compounds. A furhter application of CRT is reported in which Y-123 is biaxially textured using seeds of other Rare Earth-123 compounds with higher melting points as nucleating sites. The resultant textured microstructure exhibits mainly low angle grain boundaries (up to 5 deg. misorientation). Results will be presented on the seed alignment techniques, the development of microstructure during reaction of the composite preform and preliminary measurements of electromagnetic properties. (au). 111 refs.

Ceramic high temperature superconductors for high current applications

Energy Technology Data Exchange (ETDEWEB)

Christiansen, J

1997-12-31

Composite Reaction Texturing (CRT) is a technique which uses a fine distribution of pre-aligned seeds as nucleating sites for texturing oxide superconductors. It has successfully been applied to the texturing of Bi-2212 compounds. A furhter application of CRT is reported in which Y-123 is biaxially textured using seeds of other Rare Earth-123 compounds with higher melting points as nucleating sites. The resultant textured microstructure exhibits mainly low angle grain boundaries (up to 5 deg. misorientation). Results will be presented on the seed alignment techniques, the development of microstructure during reaction of the composite preform and preliminary measurements of electromagnetic properties. (au). 111 refs.

Ceramic high temperature superconductors for high current applications

International Nuclear Information System (INIS)

Christiansen, J.

1996-01-01

Composite Reaction Texturing (CRT) is a technique which uses a fine distribution of pre-aligned seeds as nucleating sites for texturing oxide superconductors. It has successfully been applied to the texturing of Bi-2212 compounds. A furhter application of CRT is reported in which Y-123 is biaxially textured using seeds of other Rare Earth-123 compounds with higher melting points as nucleating sites. The resultant textured microstructure exhibits mainly low angle grain boundaries (up to 5 deg. misorientation). Results will be presented on the seed alignment techniques, the development of microstructure during reaction of the composite preform and preliminary measurements of electromagnetic properties. (au)

Advanced nuclear materials development -Development of superconductor application technology-

International Nuclear Information System (INIS)

Hong, Kye Won; Lee, Heui Kyoon; Lee, Hoh Jin; Kim, Chan Joong; Jang, Kun Ik; Kim, Kee Baek; Kwon, Sun Chil; Park, Hae Woong; Yoo, Jae Keun; Kim, Jong Jin; Jang, Joong Chul; Yang, Suk Woo

1995-07-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype fly wheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies on the method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting powder with good reactivity and fine particle size was obtained by emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Tc of 16,000 A/cm 2 was fabricated by applying CIP packing procedure. Multifilamentary wire with the Jc of approx. 10000 A/cm 2 was fabricated by rolling method using square billet as starting shape. The joining of the multifilament wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. 126 figs, 14 tabs, 214 refs. (Author)

Advanced nuclear materials development -Development of superconductor application technology-

Energy Technology Data Exchange (ETDEWEB)

Hong, Kye Won; Lee, Heui Kyoon; Lee, Hoh Jin; Kim, Chan Joong; Jang, Kun Ik; Kim, Kee Baek; Kwon, Sun Chil; Park, Hae Woong; Yoo, Jae Keun; Kim, Jong Jin; Jang, Joong Chul; Yang, Suk Woo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype fly wheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies on the method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting powder with good reactivity and fine particle size was obtained by emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Tc of 16,000 A/cm{sup 2} was fabricated by applying CIP packing procedure. Multifilamentary wire with the Jc of approx. 10000 A/cm{sup 2} was fabricated by rolling method using square billet as starting shape. The joining of the multifilament wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. 126 figs, 14 tabs, 214 refs. (Author).

Effective Ginzburg–Landau free energy functional for multi-band isotropic superconductors

International Nuclear Information System (INIS)

Grigorishin, Konstantin V.

2016-01-01

Highlights: • The intergradient coupling of order parameters in a two-band superconductor plays important role and cannot be neglected. • A two-band superconductor must be characterized with a single coherence length and a single Ginzburg–Landau parameter. • Type-1.5 superconductors are impossible. • The free energy functional for a multi-band superconductor can be reduced to the effective single-band Ginzburg–Landau functional. - Abstract: It has been shown that interband mixing of gradients of two order parameters (drag effect) in an isotropic bulk two-band superconductor plays important role – such a quantity of the intergradients coupling exists that the two-band superconductor is characterized with a single coherence length and a single Ginzburg–Landau (GL) parameter. Other quantities or neglecting of the drag effect lead to existence of two coherence lengths and dynamical instability due to violation of the phase relations between the order parameters. Thus so-called type-1.5 superconductors are impossible. An approximate method for solving of set of GL equations for a multi-band superconductor has been developed: using the result about the drag effect it has been shown that the free-energy functional for a multi-band superconductor can be reduced to the GL functional for an effective single-band superconductor.

Reply to the ''Comment on 'Observation of trapped O2 in high-Tc metal oxide superconductors' ''

International Nuclear Information System (INIS)

Chen, C.H.; Phillips, R.C.; Payne, M.G.

1990-01-01

Desorption of O 2 in certain high-T c superconductors was observed from scraping the surfaces of superconductors by Rosenberg and Wen. Their conclusion agrees with the results from the observation of O 2 trapping by a laser ablation of superconductors. However, the local heating due to the scraping process can possibly raise the local surface temperature significantly higher than the temperature of the bulk

High output power reluctance electric motors with bulk high-temperature superconductor elements

Energy Technology Data Exchange (ETDEWEB)

Kovalev, L.K. [Moscow State Aviation Institute (Technical University) (MAI), Moscow (Russian Federation)]. E-mail: kovalev@mail.sitek.net; Ilushin, K.V.; Penkin, V.T. [Moscow State Aviation Institute (Technical University) (MAI), Moscow (RU)] [and others

2002-05-01

We present new types of electric machines with the rotors containing bulk high-temperature superconductor (HTS)-YBCO and Bi-Ag-elements. We discuss different schematics of hysteresis, reluctance, 'trapped field' and composed synchronous HTS machines. The two-dimensional mathematical models describing the processes in such types of HTS machines were developed on the basis of the theoretical analysis of the electrodynamic and hysteresis processes in the single-domain and polycrystal YBCO ceramic samples and plate shape Bi-Ag elements. We give the test results of the series of hysteresis, reluctance, 'trapped field' and composed with permanent magnets HTS motors with an output power rating of 0.1-18 kW and current frequencies 50 Hz and 400 Hz. These results show that in the media of liquid nitrogen the specific output power per one unit weight of the HTS motor is four to seven times better than for conventional electric machines. A comparison of the theoretical and experimental characteristics of the developed HTS motors show that they are in good agreement. We discuss the test results for a liquid nitrogen cryogenic pump system with a hysteresis 500 W HTS motor. We describe several designs of new HTS motors operating in the media of liquid nitrogen with an output power 125 kW (and more) and a power factor of more than 0.8. We discuss future applications of new types of HTS motors for aerospace technology, on-land industry and transport systems. (author)

Superconductivity, spin-glass properties, and ferromagnetism in amorphous La--Gd--Au alloys

International Nuclear Information System (INIS)

Poon, S.J.

1978-01-01

The superconducting and magnetic properties of splat cooled amorphous alloys of composition (La/sub 100-x/Gd/sub x/) 80 Au 20 (0 equal to or less than x equal to or less than 100) have been studied. The La 80 Au 20 alloys are ideal type II superconductors (critical temperature T/sub c/ = 3.5 0 K). The concentration range (x 80 Au 20 . The results are compared with recent theories on amorphous magnetism

Tricrystal tunneling evidence for d-wave pairing symmetry in cuprate superconductors

International Nuclear Information System (INIS)

Tsuei, C.C.; Kirtley, J.R.

1997-01-01

Strong evidence for d-wave pairing symmetry in high-temperature superconductors such as YBa 2 Cu 3 O 7 and Tl 2 Ba 2 CuO 6+δ has been obtained by monitoring the presence or absence of the half-integer flux quantum effect in various controlled - orientation tricrystal superconducting systems. New results of a tricrystal tunneling experiment with Gd Ba 2 Cu 3 O 7 will also be presented. (orig.)

Trapped magnetic field of a superconducting bulk magnet in high- T sub c RE-Ba-Cu-O

CERN Document Server

Fujimoto, H; Higuchi, T; Nakamura, Y; Kamijo, H; Nagashima, K; Murakami, M

1999-01-01

Superconducting magnets made of high-T sub c superconductors are promising for industrial applications. It is well known that REBa sub 2 Cu sub 3 O sub 7 sub - sub x and LRE (light rare-earth) Ba sub 2 Cu sub 3 O sub 7 sub - sub x superconductors prepared by melt processes have a high critical current density, J sub c , at 77 K and high magnetic fields. Therefore, the materials are very prospective for high magnetic field application as a superconducting permanent/bulk magnet with liquid-nitrogen refrigeration. LREBaCuO bulks, compared with REBaCuO bulks, exhibit a larger J sub c in high magnetic fields and a much improved irreversibility field, H sub i sub r sub r , at 77 K. In this study, we discuss the possibility and trapped field properties of a superconducting bulk magnet, as well as the melt processing for bulk superconductors and their characteristic superconducting properties. One of the applications is a superconducting magnet for the future magnetically levitated (Maglev) train.

Glass formability of high T(sub c) Bi-Sr-Ca-Cu-O superconductors

Science.gov (United States)

Kaukler, William F.

1992-01-01

A number of compositions of ceramic oxide high T(sub c) superconductors were evaluated for their glass formation ability by means of rapid thermal analysis during quenching, optical and electron microscopy of the quenched samples, and with subsequent DSC measurements. Correlations between experimental measurements and the methodical composition changes identified the formulations of superconductors that can easily form glass. The superconducting material was first formed as a glass, then with subsequent devitrification it was formed into bulk crystalline superconductor by a series of processing methods.

Granularity effect on microwave surface resistance in high-Tc YBa2Cu3O7-x bulk and thin film superconductor

International Nuclear Information System (INIS)

Swarup, Ram; Gupta, A.K.

2001-01-01

We report the effect of variation of Josephson coupling strength in YBa 2 Cu 3 O 7-x (YBCO) superconductor due to grain enlargement, grain orientation and magnetic field on microwave surface resistance (R s ). The coupling strength in the bulk samples has been increased by increasing the sample density from 4.4 to 5.3 g/cm 3 , whereas in thin films, the same could be increased by increasing the c-axis orientation of the grains. The value of R s (10 GHz, 65 K) in bulk samples has been found to decrease from 52 to 4 mΩ with the increase of the coupling strength from 0.06 to 0.43 and in thin films from 930 to 600 μΩ with increase of the coupling strength from 0.92 to 2.43. The effect of grain decoupling on microwave surface resistance was studied under dc and microwave magnetic fields. The surface resistance increases gradually with the application of dc and microwave magnetic fields due to grain decoupling and finally gets saturated beyond a certain critical field. (author)

Characteristic of the flux pinning at intergrain boundaries in bulk Bi-Pb-Sr-Ca-Cu-O superconductors

International Nuclear Information System (INIS)

Wang Yugui; Yang Yu; Xiong Xiaozhong; Yuan Songliu; Wang Shunxi

1991-02-01

The magnetization measurement shows that there are two kinds of different intergrain boundaries in the sintered Bi 1.8 Pb 0.34 Sr 1.86 Ca 2 Cu 3 O y superconductors. One has nearly no pinning force for flux line, the other can trap some flux line in the low field range where a pinning current may be sustained. When the applied field is removed, most of the remanent magnetization comes from the intergrain boundaries. The area of hysteresis loop at low field and the remanent magnetization for the cold-pressed bulk samples are significantly increased. Cold pressing results in aligning the grain orientation and raising the packing density, both of which enhanced intergrain coupling. The J c value of 1040 A/cm 2 at H = 0 and 150 A/cm 2 at H = 1 k Oe are obtained. The flux creep along the intergrain boundaries and the pinning potential energy U 0 for the coldpressed samples are also discussed

Grain alignment in bulk YBa2Cu3Ox superconductor by a low temperature phase transformation method

International Nuclear Information System (INIS)

Selvamanickam, V.; Goyal, A.; Kroeger, D.M.

1994-01-01

A quench and directional phase transformation process has been developed to achieve grain alignment in bulk YBa 2 Cu 3 O x superconductors at temperatures about 100 degree C below the peritectic temperature. Isothermal phase transformation of quenched precursors at 890 degree C for 3 min is found to result in the formation of more than 75% of YBa 2 Cu 3 O x phase without any formation of Y 2 BaCuO 5 . Phase transformation at higher temperatures leads to rapid formation of Y 2 BaCuO 5 in addition to YBa 2 Cu 3 O x . A well-aligned microstructure is achieved by directional phase transformation of the quenched compacts as a rate of 10 mm/h. The magnetic field dependence of the critical current density at 77 K of the directionally phase transformed material compares well with that of melt-textured YBCO and is superior to that of magnetically aligned and sintered YBCO

Method for preparation of textured YBa.sub.2 Cu.sub.3 O.sub.x superconductor

Science.gov (United States)

Selvamanickam, Venkat; Goyal, Amit; Kroeger, Donald M.

1998-01-01

The present invention relate to textured YBa.sub.2 Cu.sub.3 O.sub.x (Y-123) superconductors and a process of preparing them by directional recrystallization of compacts fabricated from quenched YBCO powders at temperatures about 100.degree. C. below the peritectic temperature to provide a superconductor where more than 75% of the YBa.sub.2 Cu.sub.3 O.sub.x phase is obtained without any Y.sub.2 BaCuO.sub.5 .

Structure evolution and magnetic properties of annealed nanoscale Gd/Ti multilayers

Directory of Open Access Journals (Sweden)

Larrañaga A.

2013-01-01

Full Text Available The structure and magnetic properties were comparatively analyzed for [Gd/Ti]n multilayers with Gd layer thickness of 1.5 to 12 nm. Multilayers were deposited by sputtering technique at room temperature and annealed for the temperatures up to 400 ºC. It was observed that the samples are highly textured in a different way depending on the Gd layer thickness and annealing temperature. It was found that the heat treatment practically does not change the Gd grain size. The lattice parameters obtained from X-ray results change significantly only for [Gd(1.5nm/Ti]50 multilayers, but their values remain higher than for the bulk Gd. The initial slope of the temperature dependence of magnetization near Curie temperature becomes steeper and Curie temperature increases upon annealing. Curie temperature variation can be understood by taking into account both relaxation of the lattice imperfections and change in lattice constants.

Application of high temperature superconductors for fusion

International Nuclear Information System (INIS)

Fietz, W.H.; Heller, R.; Schlachter, S.I.; Goldacker, W.

2011-01-01

The use of High Temperature Superconductor (HTS) materials in future fusion machines can increase the efficiency drastically. For ITER, W7-X and JT-60SA the economic benefit of HTS current leads was recognized after a 70 kA HTS current lead demonstrator was designed, fabricated and successfully tested by Karlsruhe Institute of Technology (KIT, which is a merge of former Forschungszentrum Karlsruhe and University of Karlsruhe). For ITER, the Chinese Domestic Agency will provide the current leads as a part of the superconducting feeder system. KIT is in charge of design, construction and test of HTS current leads for W7-X and JT-60SA. For W7-X 14 current leads with a maximum current of 18.2 kA are required that are oriented with the room temperature end at the bottom. JT60-SA will need 26 current leads (20 leads - 20 kA and 6 leads - 25.7 kA) which are mounted in vertical, normal position. These current leads are based on BiSCCO HTS superconductors, demonstrating that HTS material is now state of the art for highly efficient current leads. With respect to future fusion reactors, it would be very promising to use HTS material not only in current leads but also in coils. This would allow a large increase of efficiency if the coils could be operated at temperatures ≥65 K. With such a high temperature it would be possible to omit the radiation shield of the coils, resulting in a less complex cryostat and a size reduction of the machine. In addition less refrigeration power is needed saving investment and operating costs. However, to come to an HTS fusion coil it is necessary to develop low ac loss HTS cables for currents well above 20 kA at high fields well above 10 T. The high field rules BiSCCO superconductors out at temperatures above 50 K, but RE-123 superconductors are promising. The development of a high current, high field RE-123 HTS fusion cable will not be targeted outside fusion community and has to be in the frame of a long term development programme for

The Pr and Ca substitution in GdBa2Cu3O7-8

International Nuclear Information System (INIS)

Shakeri, H.; Akhavan, M.

2002-01-01

The granular Gd 1 -x-zPr x Ca z Ba 2 Cu 3 O 7 -8 (Gd Pr Ca-123) high-temperature cuprate samples with 0.0≤x≤0.3 and 0.0≤z≤0.35 are prepared by standard solid state reaction and characterized by XRD and SEM techniques. The BaCuO 2 and impurity phases are less than 1% in the samples having high levels of Pr and Ca concentrations. The electrical resistivity measurements show a nonlinear reduction in T c (x,z=etc) versus x. Moreover, the T c (z) curve with x=0 is nonlinear and a plateau appears at z≅0.05-0.015. For Pr-Ca-doped samples with a constant concentration of Pr, T c increases with the increase of Ca up to an optimum value of Ca doping and then in decreases. Based on these observations, we suggest that hole filling and hole localization the main effects of Pr ion substitution. The magnetic measurements indicate that the value of H C 1 is in the order of 10 m T. The magnetoresistance measurements have been measured and analyzed. The superconducting transition region is broadened by the application of magnetic field. The experimental data near the on sen of superconductivity are fitted with the Ambegakor and Halperin (A H) phase-slip model. We observe that the A H parameter, γ(H), depends not only on the temperature and the magnetic field, but also on the Pr and Ca ions concentrations. It is observed that the critical current density increases with Ca substitution and decreases with pr substitution in Gd-123 system. We suggest that the pr ion substitution probably enhances the weak link, but the Ca ion acts as flux pinning center in the Gd Pr Ca-123 system

Synthesis and photoluminescence properties of GdBO3:Ln3+ (Ln = Eu, Tb) nanofibers by electrospinning

International Nuclear Information System (INIS)

Shen, Hongzhi; Feng, Shuo; Wang, Ying; Gu, Yipeng; Zhou, Jing; Yang, Hang; Feng, Guanlin; Li, Liang; Wang, Wenquan; Liu, Xiaoyang; Xu, Dapeng

2013-01-01

Highlights: ► GdBO 3 :Ln 3+ nanofibers were synthesized successfully by electrospinning. ► The samples have the average diameter of 150 nm and the flexible morphology. ► The GdBO 3 : Eu 3+ nanofibers have the stronger orange emission. ► The luminescence properties are different from the reported bulk material. ► We describe the energy transform process of GdBO 3 :Ln 3+ system. - Abstract: GdBO 3 :Ln 3+ (Ln = Eu, Tb) nanofibers were synthesized using electrospinning combined with heat treatment. The synthesized nanofibers were characterized by X-ray diffraction, Raman spectroscopy, field emission-scanning electron microscopy, thermogravimetric and differential thermal analyses, and photoluminescence. The experimental results show that the flexible synthesized nanofibers have an average diameter of approximately 150 nm. The nanofibers consist of crystalline grains with diameters of about 40 nm and have a vaterite-type structure of GdBO 3 . The GdBO 3 :Eu 3+ nanofibers exhibit strong orange and weak red emissions with a low ratio of red to orange emission intensities, which is different from those of the reported bulk materials and nanoparticles. The luminescence properties of the synthesized GdBO 3 :Tb 3+ nanofibers are essentially consistent with those of the synthesized GdBO 3 :Tb 3+ powders by solid-state reaction.

Enhanced flux pinning by BaZrO3 and (Gd,y)2O3 nano-structures in metal organic chemical vapor deposited GdYBCO high temperature superconductor tapes

Energy Technology Data Exchange (ETDEWEB)

Chen, Y [SuperPower Incorporated, Schenectady, New York; Selvamanickam, V. [SuperPower Incorporated, Schenectady, New York; Paranthaman, Mariappan Parans [ORNL; Cantoni, Claudia [ORNL; Aytug, Tolga [ORNL; Goyal, Amit [ORNL; Lee, Dominic F [ORNL; Specht, Eliot D [ORNL; Zuev, Yuri L [ORNL; Zhang, Yifei [ORNL

2009-01-01

We have formed BaZrO3 nano-columns and (Gd,Y)2O3 nano-precipitates in reel-to-reel MOCVD processed (Gd,Y)Ba2Cu3O7-x coated conductors and increased the critical currents (Ic) of the conductors in applied magnetic fields to remarkable levels. A (Gd,Y)Ba2Cu3O7-x tape of 1m length with 6.5% Zr-additions and 30% composition rich in both Gd and Y showed Ic values of 813 A/cm-width at (self-field, 77K) and above 186 A/cm-width at (1T, 77K). The strongly enhanced flux pinning over a wide range of magnetic field orientations can be attributed to the bidirectionally aligned defect structures of BaZrO3 and (Gd,Y)2O3 created by optimized MOCVD conditions.

Comparative Review on Thin Film Growth of Iron-Based Superconductors

Directory of Open Access Journals (Sweden)

Yoshinori Imai

2017-07-01

Full Text Available Since the discovery of the novel iron-based superconductors, both theoretical and experimental studies have been performed intensively. Because iron-based superconductors have a smaller anisotropy than high-Tc cuprates and a high superconducting transition temperature, there have been a lot of researchers working on the film fabrication of iron-based superconductors and their application. Accordingly, many novel features have been reported in the films of iron-based superconductors, for example, the fabrication of the epitaxial film with a higher Tc than bulk samples, the extraction of the metastable phase which cannot be obtained by the conventional solid state reaction, and so on. In this paper, we review the progress of research on thin film fabrications of iron-based superconductors, especially the four categories: LnFeAs(O,F (Ln = Lanthanide, AEFe2As2 (AE = Alkaline-earth metal, FeCh (Ch = Chalcogen, and FeSe monolayer. Furthermore, we focus on two important topics in thin films of iron-based superconductors; one is the substrate material for thin film growth on the iron-based superconductors, and the other is the whole phase diagram in FeSe1-xTex which can be obtained only by using film-fabrication technique.

Neutron-diffraction investigations of flux-lines in superconductors

Energy Technology Data Exchange (ETDEWEB)

Forgan, E M [Birmingham Univ. (United Kingdom); Lee, S L [Saint Andrews Univ. (United Kingdom); McKPaul, D [Warwick Univ., Coventry (United Kingdom); Mook, H A [Oak Ridge National Lab., TN (United States); Cubitt, R [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

1997-04-01

SANS has proved an extremely useful tool for investigating flux-line structures within the bulk of superconductors. With high-T{sub c} materials, the scattered intensities are weak, but careful measurements are giving important new information about flux lattices, flux pinning and flux-lattice melting. (author). 10 refs.

Surface Andreev Bound States and Odd-Frequency Pairing in Topological Superconductor Junctions

Science.gov (United States)

Tanaka, Yukio; Tamura, Shun

2018-04-01

In this review, we summarize the achievement of the physics of surface Andreev bound states (SABS) up to now. The route of this activity has started from the physics of SABS of unconventional superconductors where the pair potential has a sign change on the Fermi surface. It has been established that SABS can be regarded as a topological edge state with topological invariant defined in the bulk Hamiltonian. On the other hand, SABS accompanies odd-frequency pairing like spin-triplet s-wave or spin-singlet p-wave. In a spin-triplet superconductor junction, induced odd-frequency pairing can penetrate into a diffusive normal metal (DN) attached to the superconductor. It causes so called anomalous proximity effect where the local density of states of quasiparticle in DN has a zero energy peak. When bulk pairing symmetry is spin-triplet px-wave, the anomalous proximity effect becomes prominent and the zero bias voltage conductance is always quantized independent of the resistance in DN and interface. Finally, we show that the present anomalous proximity effect is realized in an artificial topological superconducting system, where a nanowire with spin-orbit coupling and Zeeman field is put on the conventional spin-singlet s-wave superconductor.

The Born-Mayer-Huggins potential in high temperature superconductors

Science.gov (United States)

Singh, Hempal; Singh, Anu; Indu, B. D.

2016-07-01

The Born-Mayer-Huggins potential which has been found the best suitable potential to study the YBa2Cu3O7-δ type high temperature superconductors is revisited in a new framework. A deeper insight in it reveals that the Born-Mayer parameters for different interactions in high temperature superconductor are not simple quantities but several thermodynamic and spatial functions enter the problem. Based on the new theory, the expressions for pressure, bulk modulus and Born-Mayer parameters have been derived and it is established that these quantities depend upon Gruneisen parameter which is the measure of the strength of anharmonic effects in high temperature superconductors. This theory has been applied to a specific model YBa2Cu3O7-δ crystal for the purpose of numerical estimates to justify the new results.

Possibility of a high-T{sub c} superconducting bulk magnet for maglev trains in the future; Koonchodendo baruku jishaku no jikifujoshiki tetudo heno oyo kanosei

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H. [Railway Technical Research Institute, Fundamental Research Division, Tokyo (Japan)

1999-11-25

Superconducting magnets made of high-T{sub c} superconductors are promising for industrial applications. It is well known that REBa{sub 2}Cu{sub 3}O{sub 7-x} superconductors prepared by melt processes have a high critical current density, J{sub c}, at 77K and high magnetic fields. The materials are very prospective for high magnetic field application as a superconducting permanent/bulk magnet with liquid-nitrogen refrigeration. LREBaCuO bulks, compared with REBaCuO bulks, exhibit a larger, J{sub c} in high magnetic fields and a much improved irreversibility field, H{sub irr}, at 77K. In this study, we discuss the possibility and trapped field properties of a superconducting bulk magnet, as well as the melt processing for bulk superconductors and their characteristic superconducting and mechanical properties. One of the applications is a superconducting bulk magnet for future magnetically levitated (Maglev) trains. (author)

Properties of amorphous and microcrystalline superconductors

International Nuclear Information System (INIS)

Johnson, W.L.; Poon, S.J.

1975-01-01

Results of x-ray diffraction, electrical resistivity, critical field(H/sub c2/) and transport measurements are presented and discussed for bulk amorphous and microcrystalline transition metal alloys (Au--La, Nb--Rh, Nb--Ni--Rh, and Pd--Zr) obtained by liquid quenching. The transition temperature of the alloys is in the range 1.5 to 4.7 0 K. The J/sub c/--H/sub c2/--T/sub c/ relations are rather simple for this class of material and are compared with the theories of type II superconductors. The high resistance of bulk metallic glass to radiation damage might render them suitable for magnetic field applications in high radiation environments

Electronic structure and superconductivity of FeSe-related superconductors.

Science.gov (United States)

Liu, Xu; Zhao, Lin; He, Shaolong; He, Junfeng; Liu, Defa; Mou, Daixiang; Shen, Bing; Hu, Yong; Huang, Jianwei; Zhou, X J

2015-05-13

FeSe superconductors and their related systems have attracted much attention in the study of iron-based superconductors owing to their simple crystal structure and peculiar electronic and physical properties. The bulk FeSe superconductor has a superconducting transition temperature (Tc) of ~8 K and it can be dramatically enhanced to 37 K at high pressure. On the other hand, its cousin system, FeTe, possesses a unique antiferromagnetic ground state but is non-superconducting. Substitution of Se with Te in the FeSe superconductor results in an enhancement of Tc up to 14.5 K and superconductivity can persist over a large composition range in the Fe(Se,Te) system. Intercalation of the FeSe superconductor leads to the discovery of the AxFe2-ySe2 (A = K, Cs and Tl) system that exhibits a Tc higher than 30 K and a unique electronic structure of the superconducting phase. A recent report of possible high temperature superconductivity in single-layer FeSe/SrTiO3 films with a Tc above 65 K has generated much excitement in the community. This pioneering work opens a door for interface superconductivity to explore for high Tc superconductors. The distinct electronic structure and superconducting gap, layer-dependent behavior and insulator-superconductor transition of the FeSe/SrTiO3 films provide critical information in understanding the superconductivity mechanism of iron-based superconductors. In this paper, we present a brief review of the investigation of the electronic structure and superconductivity of the FeSe superconductor and related systems, with a particular focus on the FeSe films.

Entanglement entropy and complexity for one-dimensional holographic superconductors

Science.gov (United States)

Kord Zangeneh, Mahdi; Ong, Yen Chin; Wang, Bin

2017-08-01

Holographic superconductor is an important arena for holography, as it allows concrete calculations to further understand the dictionary between bulk physics and boundary physics. An important quantity of recent interest is the holographic complexity. Conflicting claims had been made in the literature concerning the behavior of holographic complexity during phase transition. We clarify this issue by performing a numerical study on one-dimensional holographic superconductor. Our investigation shows that holographic complexity does not behave in the same way as holographic entanglement entropy. Nevertheless, the universal terms of both quantities are finite and reflect the phase transition at the same critical temperature.

Magnetic, electrical and structural properties of the Re-doped ruthenocuprate Ru{sub 1−x}Re{sub x}Sr{sub 2}GdCu{sub 2}O{sub y}

Energy Technology Data Exchange (ETDEWEB)

Corredor, L.T. [Departamento de Física, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil); Programa de Pós-Graduação em Ciências de Materiais-CCEN, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil); Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, Bogotá D.C. (Colombia); Albino Aguiar, J. [Departamento de Física, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil); Programa de Pós-Graduação em Ciências de Materiais-CCEN, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil); Landínez Téllez, D.A. [Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, Bogotá D.C. (Colombia); Pureur, P.; Mesquita, F. [Instituto de Física, Universidade Federal do Rio Grande do Sul, 91501-970 Porto Alegre, RS (Brazil); Roa-Rojas, J. [Grupo de Física de Nuevos Materiales, Departamento de Física, Universidad Nacional de Colombia, Bogotá D.C. (Colombia)

2015-06-15

Highlights: • We investigated the effect of the dilution of magnetic Ru sub-lattice of RuSr{sub 2}GdCu{sub 2}O{sub 8}. • We synthesized the doped compound Rui{sub x}Re{sub x}Sr{sub 2}GdCu{sub 2}O{sub y}, for 3%, 6%, 9% and 12% Re. • Re would affect the electron coupling: just 3 and 6% samples were superconductor. • Superconductivity emergence strongly affects magnetic properties of 3 and 6% samples. • A weak ferromagnetic component is consistent with a globally antiferromagnetic system. - Abstract: Despite the discovery of new superconductors classes, high-Tc oxides continue to be a current topic, because of their complex phase diagrams and doping-dependant effects (allowing one to investigate the interaction between orbitals), as well as structural properties such as lattice distortion and charge ordering, among many others. Ruthenocuprates are magnetic superconductors in which the magnetic transition temperature is much higher than the critical superconducting temperature, making them unique compounds. With the aim of investigating the dilution of the magnetic Ru sub-lattice, we proposed the synthesis of the Ru{sub 1−x}Re{sub x}Sr{sub 2}GdCu{sub 2}O{sub y} ruthenocuprate-type family, adapting the known two-step process (double perovskite + CuO) by directly doping the double perovskite, thus obtaining the perovskite compound Sr{sub 2}GdRu{sub 1−x}Re{sub x}O{sub y}, which represents a new synthesis process to the best of our knowledge. Our samples were structurally characterized through X-ray diffraction, and the patterns were analysed via Rietveld refinement. A complete magnetic characterization as a function of temperature and applied field, as well as transport measurements were carried out. We discuss our results in the light of the two-lattice model for ruthenocuprates, and a relation between RuO{sub 2} (magnetic) and CuO{sub 2} (superconductor) sub-lattices can clearly be observed.

Static Test for a Gravitational Force Coupled to Type 2 YBCO Superconductors

Science.gov (United States)

Li, Ning; Noever, David; Robertson, Tony; Koczor, Ron; Brantley, Whitt

1997-01-01

As a Bose condensate, superconductors provide novel conditions for revisiting previously proposed couplings between electromagnetism and gravity. Strong variations in Cooper pair density, large conductivity and low magnetic permeability define superconductive and degenerate condensates without the traditional density limits imposed by the Fermi energy (approx. 10(exp -6) g cc. Recent experiments have reported anomalous weight loss for a test mass suspended above a rotating type II, YBCO superconductor, with the percentage change (0.05 - 2.1 %) independent of the test mass' chemical composition and diamagnetic properties. A variation of 5 parts per 10' was reported above a stationary (non-rotating) superconductor. In experiments using a sensitive gravimeter, bulk YBCO superconductors were stably levitated in a DC magnetic field. Changes in acceleration were measured to be less than 2 parts in 108 of the normal gravitational acceleration. This result puts new limits on the strength and range of the proposed coupling between static superconductors and gravity.

Thermal properties of GdSr{sub 2}RuCu{sub 2}O{sub 8-{delta}} based mixtures in the GdSr{sub 2}RuO{sub 6}-CuO pseudo-binary system

Energy Technology Data Exchange (ETDEWEB)

Gombos, Marcello [Laboratorio Regionale Supermat CNR-INFM Via Salvador Allende, I-84081 Baronissi (Italy); Dipartimento di Fisica ' E.R.Caianiello' , Universita di Salerno, Via Salvador Allende, I-84081 Baronissi (Italy)], E-mail: gombos@sa.infn.it; Ciancio, Regina; Vecchione, Antonio; Pace, Sandro [Laboratorio Regionale Supermat CNR-INFM Via Salvador Allende, I-84081 Baronissi (Italy); Dipartimento di Fisica ' E.R.Caianiello' , Universita di Salerno, Via Salvador Allende, I-84081 Baronissi (Italy)

2007-09-01

GdSr{sub 2}RuCu{sub 2}O{sub 8-{delta}} (Gd1212) rutheno-cuprate compound is widely studied because it shows the coexistence of superconductivity and highly anisotropic magnetic ordering in the same cell. Anyway the nature of the magnetic ordering is still debated and the fabrication of macroscopic samples oriented along a crystallographic axis, that could help to clarify its details, appears to be quite difficult. For this reason, accurate investigation on Gd1212 incongruent melting reaction, producing liquid copper oxide and the solid GdSr{sub 2}RuO{sub 6} (Gd1210), appears to be necessary to improve the fabrication of crystallographically oriented bulk superconducting samples. Thermo-gravimetric and differential thermal measurements were performed to analyse the thermal behaviour up to 1200 deg. C and the melting temperatures of different mixtures of Gd1212 with Gd1210 or CuO, in view to perform a scan of the whole CuO-Gd1212-Gd1210 coexistence line of the Gd-Sr-Ru-Cu-O phase diagram. Dependence on the atmosphere and the formation of different spurious phases was also studied.

Coasting characteristic of the flywheel system under anisotropy effect of bulk high temperature superconductors

International Nuclear Information System (INIS)

Wu, J.F.; Li, Y.

2014-01-01

Highlights: • Coasting time was investigated from the point-view of HTS flywheel applications. • The coasting time of aligned growth section boundary pattern (AGSBP) is shorter than that of MGSBP. • The electric magnetic drag force with AGSBP is larger than that of MGSBP. • This result may also exist in the maglev guideline when the maglev train stops freely. - Abstract: High-temperature superconductors (HTSCs) array with aligned growth section boundary (GSB) pattern (AGSBP) exhibits larger levitation force and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP) has been studied in maglev train application (Zheng et al., 2013). This result maybe helpful and support a new way for the HTS bearing design for flywheel systems. So, in this paper, we further examine this growth anisotropy effect on the maglev performance of flywheel system. Levitation force and coasting time were investigated from the point-view of HTS flywheel applications. The GS/GSB alignment of AGSBP bulk HTSCs produces larger levitation force than that of MGSBP, but the coasting time is shorter than that of MGSBP, that is to say, the electric magnetic drag force with AGSBP is larger than that of MGSBP. This result may also exist in the maglev guideline when the maglev train stops freely

Coasting characteristic of the flywheel system under anisotropy effect of bulk high temperature superconductors

Energy Technology Data Exchange (ETDEWEB)

Wu, J.F., E-mail: wujf@ciomp.ac.cn; Li, Y.

2014-10-15

Highlights: • Coasting time was investigated from the point-view of HTS flywheel applications. • The coasting time of aligned growth section boundary pattern (AGSBP) is shorter than that of MGSBP. • The electric magnetic drag force with AGSBP is larger than that of MGSBP. • This result may also exist in the maglev guideline when the maglev train stops freely. - Abstract: High-temperature superconductors (HTSCs) array with aligned growth section boundary (GSB) pattern (AGSBP) exhibits larger levitation force and suppression of levitation force decay above a permanent magnet guideway (PMG) compared with misaligned GSB pattern (MGSBP) has been studied in maglev train application (Zheng et al., 2013). This result maybe helpful and support a new way for the HTS bearing design for flywheel systems. So, in this paper, we further examine this growth anisotropy effect on the maglev performance of flywheel system. Levitation force and coasting time were investigated from the point-view of HTS flywheel applications. The GS/GSB alignment of AGSBP bulk HTSCs produces larger levitation force than that of MGSBP, but the coasting time is shorter than that of MGSBP, that is to say, the electric magnetic drag force with AGSBP is larger than that of MGSBP. This result may also exist in the maglev guideline when the maglev train stops freely.

Influence of lateral displacement on the levitation performance of a magnetized bulk high-Tc superconductor magnet

International Nuclear Information System (INIS)

Liu, W.; Wang, J.S.; Ma, G.T.; Zheng, J.; Tuo, X.G.; Li, L.L.; Ye, C.Q.; Liao, X.L.; Wang, S.Y.

2012-01-01

Compared with the permanent magnet, the magnetized bulk high-T c superconductor magnet (MBSCM) can trap higher magnetic field due to its strong flux pinning ability, so it is a good candidate to improve the levitation performance of high-T c superconductive (HTS) maglev system. The trapped magnetic flux of a MBSCM is sustained by the inductive superconducting current produced by the magnetizing process and is susceptible to the current intensity as well as configuration. In the HTS maglev system, the lateral displacement is an important process to change the superconducting current within a MBSCM and then affects its levitation performance, which is essential for the traffic ability in curve-way, the loading capacity of lateral impact and so on. The research about influence of lateral displacement on the levitation performance of MBSCM is necessary when MBSCM is applied on the HTS maglev vehicle. The experimental investigations about the influence of lateral displacement on the levitation performance of a MBSCM with different trapped fluxes and applied fields are processed in this article. The analyses and conclusions of this article are useful for the practical application of MBSCM in HTS maglev system.

Magnetization fluctuation analysis and superconducting parameters of La0.5RE0.5BaCaCu3O7-δ(RE=Y, Sm, Gd, Dy, Ho, Yb) superconductor

International Nuclear Information System (INIS)

Parra Vargas, C.A.; Pimentel, J.L.; Pureur, P.; Landinez Tellez, D.A.; Roa-Rojas, J.

2009-01-01

In this work we report the analysis of magnetization experimental data of the La 0.5 RE 0.5 BaCaCu 3 O 7-δ (RE=Y, Sm, Gd, Dy, Ho, Yb) superconducting system. The data are analyzed in terms of thermal fluctuations on the magnetization excess ΔM(T) for different values of temperature in each one of the samples. We describe a procedure for extracting the penetration depth λ ab (∼1571A) and the coherence length ξ ab (∼1.52A) parameters from the magnetization, as a function of the applied magnetic field. This procedure was performed for polycrystalline samples of La 0.5 RE 0.5 BaCaCu 3 O 7-δ by using the theory of Bulaevskii, Ledvij and Kogan, which analyzes the vortex fluctuation in superconducting materials within the Lawrence-Doniach framework. These data allowed to determine the characteristic temperature value T * (73, 58, 48, 57, 56, 71 K, for RE=Y, Sm, Gd, Dy, Ho, Yb, respectively) in the magnetization curves for several magnetic fields. We calculated the data of magnetization excess from the curves of magnetization as a function of logarithm of applied field. We notice that the values for these superconducting parameters are in agreement with the reports for high temperature superconductors. The obtained value of superconducting volumetric fraction is compared with that obtained through the measure of the Meissner effect.

Calculation and analysis of thermodynamic relations for superconductors

International Nuclear Information System (INIS)

Nazarenko, A.B.

1989-01-01

The absorption coefficients of high-frequency and low-frequency sound have been calculated on the basis of the Ginzburg-Landau theory. This sound is a wave of periodic adiabatic bulk compressions and rarefactions of the frequency ω in an isotropic superconductor near the transition temperature. Thermodynamic relations have been obtained for abrupt changes in the physical quantities produced as a result of a transition from the normal state to the superconducting state. These relations are similar to the Ehrenfest relations. The above--mentioned thermodynamic quantities are compared with the published experimental results on YBa 2 Cu 3 O 7-δ . The experiments on the absorption of ultrasound in recently discovered superconductors mainformation on the phase transition type and thermodynamic relations for these superconductors, in particular, the T c -vs-dp curve. Similar calculations have been carried out for 2 He-transition experiments with ferromagnetic materials. The order parameter in the thermodynamic potential was assumed to be isotropic

Thin film superconductors and process for making same

Science.gov (United States)

Nigrey, P.J.

1988-01-21

A process for the preparation of oxide superconductors from high-viscosity non-aqueous solution is described. Solutions of lanthanide nitrates, alkaline earth nitrates and copper nitrates in a 1:2:3 stoichiometric ratio, when added to ethylene glycol containing citric acid solutions, have been used to prepare highly viscous non-aqueous solutions of metal mixed nitrates-citrates. Thin films of these compositions are produced when a layer of the viscous solution is formed on a substrate and subjected to thermal decomposition.

The new Fe-based superconductors

International Nuclear Information System (INIS)

Mao, Zhiqiang

2011-01-01

The discovery of unconventional superconductivity in doped iron pnictides has ushered in a new era of high temperature superconductivity. The superconductivity of these materials occurs in close proximity to magnetic instability; superconductivity is achieved by suppressing a long-range antiferromagnetic (AFM) order through charge carrier doping or pressure. In this talk, I will first give a brief overview of the phase diagrams of iron-based superconductors, and then talk about our recent research on iron chalcogenide Fe 1+y (Te 1-x Se x ) superconductors, which is structurally the simplest of the Fe-based superconductors. Although the Fermi surface of iron chalcogenides is similar to iron pnictides, the parent compound Fe 1+y Te exhibits AFM order with in-plane magnetic wave-vector (π, 0). This contrasts the pnictide parent compounds where the magnetic order has an in-plane magnetic wave-vector (π, π) that connects hole and electron parts of the Fermi surface. Despite these differences, both the pnictide and chalcogenide Fe-superconductors exhibit superconducting spin resonances around (π, π), suggesting a common symmetry for their superconducting order parameter. A central question in this burgeoning field is therefore how (π, π) superconductivity can emerge from a (π, 0) magnetic instability. I will address this issue in my talk. I will show the phase diagram of electronic and magnetic properties we recently established for this system and discuss the relationship between magnetic coupling and electronic properties. Our results reveal that the magnetic soft mode evolving from the (π, 0)-type magnetic long-range order is associated with weak charge carrier localization. Bulk superconductivity occurs only as magnetic correlations near (π, 0) are strongly suppressed and the magnetic mode at (π, π) becomes dominant; this suggests a common magnetic origin for superconductivity in iron chalcogenide and pnictide superconductors. (author)

Inter-band and intra-band reflections in graphene–insulator–superconductor junctions with zigzag or armchair edge

Energy Technology Data Exchange (ETDEWEB)

Duque, M.F., E-mail: mfduqued@unal.edu.co; Gomez P, S., E-mail: sgomezp@unal.edu.co; Herrera, W.J., E-mail: jherreraw@unal.edu.co

2014-12-15

We analyze electron–electron and Andreev reflections (AR) for a graphene–insulator–superconductor junction for zigzag and armchair edges, where the insulator is modeled as a potential barrier characterized by a strength. We calculate the reflection probabilities and differential conductance using the Bogoliubov–de Gennes–Dirac (BdGD) equations. For low doping values and zigzag edge the reflection coefficients have the same behavior that in a graphene–superconductor junction. However for high doping values the reflection probabilities have a periodicity of πwith the strength barrier values. For high doping values and armchair edge the electron–electron reflections associated to K′ valley increase and AR associated to K valley decrease. We compare our results with the differential conductance obtained by the Green formalism. We show that the effect of barrier strength for high doping resembles the behavior when a hopping between graphene and superconductor interfaces is considered.

Stoichiometric analysis of Y-Ba-Cu-O superconductors using deuterons

International Nuclear Information System (INIS)

Tang, S.M.; Ong, T.H.; Tan, M.G.; Loh, K.K.; Sow, C.H.; Yuan, B.; Orlic, I.

1993-01-01

In principle, deuteron irradiation can be used for a complete stoichiometric analysis of Y-Ba-Cu-O superconductors. The contents of all the four chemical constituents can be determined by simultaneous detection of the 0.871 MeV prompt gamma rays from the 16 O(d, pγ) 17 O * reaction and of the characteristic X-rays produced by DIXE (deuteron induced X-ray emission). In this paper we present the approach taken and the results obtained in exploring the applicability of this technique for accurate quantitative determinations of the chemical constituents of bulk Y-Ba-Cu-O superconductors. (orig.)

Magnetic properties of Eu doped BiGdO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Nithya, R., E-mail: nithya@igcar.gov.in; Yadagiri, K. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, 603 102, TN (India); Shukla, Neeraj [UGC-DAE-CSR Kalpakkam Node, Kokilamedu-603 104, TN (India)

2016-05-23

Bulk Bismuth Gadolinium Oxide, BiGdO{sub 3} and Eu doped BiGdO{sub 3} compounds were synthesized by the conventional solid state reaction in air. Phase formation of these compounds was tracked using powder X-ray characterization technique since single phase formation was found to be sensitive to thermal treatment parameters such as cooling and heating rates. Analysis of X-ray diffraction patterns revealed cubic structure with Pm-3m symmetry. An antiferromagnetic transition around 3.8 K was observed in the pristine compound whereas doped samples showed paramagnetic nature in the whole measured temperature range.

Block copolymer self-assembly–directed synthesis of mesoporous gyroidal superconductors

Science.gov (United States)

Robbins, Spencer W.; Beaucage, Peter A.; Sai, Hiroaki; Tan, Kwan Wee; Werner, Jörg G.; Sethna, James P.; DiSalvo, Francis J.; Gruner, Sol M.; Van Dover, Robert B.; Wiesner, Ulrich

2016-01-01

Superconductors with periodically ordered mesoporous structures are expected to have properties very different from those of their bulk counterparts. Systematic studies of such phenomena to date are sparse, however, because of a lack of versatile synthetic approaches to such materials. We demonstrate the formation of three-dimensionally continuous gyroidal mesoporous niobium nitride (NbN) superconductors from chiral ABC triblock terpolymer self-assembly–directed sol-gel–derived niobium oxide with subsequent thermal processing in air and ammonia gas. Superconducting materials exhibit a critical temperature (Tc) of about 7 to 8 K, a flux exclusion of about 5% compared to a dense NbN solid, and an estimated critical current density (Jc) of 440 A cm−2 at 100 Oe and 2.5 K. We expect block copolymer self-assembly–directed mesoporous superconductors to provide interesting subjects for mesostructure-superconductivity correlation studies. PMID:27152327

Block copolymer self-assembly-directed synthesis of mesoporous gyroidal superconductors.

Science.gov (United States)

Robbins, Spencer W; Beaucage, Peter A; Sai, Hiroaki; Tan, Kwan Wee; Werner, Jörg G; Sethna, James P; DiSalvo, Francis J; Gruner, Sol M; Van Dover, Robert B; Wiesner, Ulrich

2016-01-01

Superconductors with periodically ordered mesoporous structures are expected to have properties very different from those of their bulk counterparts. Systematic studies of such phenomena to date are sparse, however, because of a lack of versatile synthetic approaches to such materials. We demonstrate the formation of three-dimensionally continuous gyroidal mesoporous niobium nitride (NbN) superconductors from chiral ABC triblock terpolymer self-assembly-directed sol-gel-derived niobium oxide with subsequent thermal processing in air and ammonia gas. Superconducting materials exhibit a critical temperature (T c) of about 7 to 8 K, a flux exclusion of about 5% compared to a dense NbN solid, and an estimated critical current density (J c) of 440 A cm(-2) at 100 Oe and 2.5 K. We expect block copolymer self-assembly-directed mesoporous superconductors to provide interesting subjects for mesostructure-superconductivity correlation studies.

Theory of disordered superconductors

International Nuclear Information System (INIS)

Wysokinski, K.I.

1991-01-01

The influence of disorder on the superconducting transition temperature is discussed. The main steps on the way to complete theory of disordered superconductors follows the steps in the authors' understanding of disorder and its effect on the quasiparticles in metals. Loosely speaking one can distinguish three such steps. First is the study of weakly disordered systems and this resulted in famous, celebrated Anderson theorem. The second step is ultimately connected with the coherent potential approximation as a method to study the spectrum and transport in concentrated alloys. The discovery of the role of usually neglected interferences between scattered waves in disordered conductors leading to decrease in mobility and increase of the mutual interactions between quantum particles, known as localization and interaction effects has given the new impetus to the theory of superconductivity. This is third step to be discussed in this lecture. The authors limit themselves to homogeneous bulk superconductors. In this paper some experiments on thin films as well as on copper oxides related to the presented theory are briefly mentioned

Critical current enhancement in high Tc superconductors

International Nuclear Information System (INIS)

Jin, S.; Graebner, J.E.; Tiefel, T.H.

1990-01-01

Progress toward major technological applications of the bulk, high T c superconductors has been hindered by two major barriers, i.e., the Josephson weak-links at grain boundaries and the lack of sufficient intragrain flux pinning. It has been demonstrated that the weak link problem can be overcome by extreme alignment of grains such as in melt-textured-growth (MTG) materials. Modified or improved processing by various laboratories has produced further increased critical currents. However, the insufficient flux pinning seems to limit the critical current density in high fields to about 10 4 --10 5 A/cm 2 at 77K, which is not satisfactory for many applications. In this paper, processing, microstructure, and critical current behavior of the MTG type superconductors are described, and various processing possibilities for flux pinning enhancement are discussed

Fermi surface deformation in a simple iron-based superconductor, FeSe

Science.gov (United States)

Coldea, Amalia; Watson, Matthew; Kim, Timur; Haghighirad, Amir; McCollam, Alix; Hoesch, Moritz; Schofield, Andrew

2015-03-01

One of the outstanding problems in the field superconductivity is the identification of the normal state out of which superconductivity emerges. FeSe is one of the simplest and most intriguing iron-based superconductors, since in its bulk form it undergoes a structural transition before it becomes superconducting, whereas its single-layer form is believed to be a high-temperature superconductor. The nature of the structural transition, occurring in the absence of static magnetism, is rather unusual and how the electronic structure is stabilized by breaking of the rotational symmetry is the key to understand the superconductivity in bulk FeSe. Here we report angle-resolved photoemission spectroscopy measurements on FeSe that gives direct access to the band structure and orbital-dependent effects. We complement our studies on bulk FeSe with low-temperature angular-dependent quantum oscillation measurements using applied magnetic fields that are sufficiently strong to suppress superconductivity and reach the normal state. These studies reveal a strong deformation of Fermi surface through the structural transition driven by electronic correlations and orbital-dependent effects. . This work was supported by EPSRC, UK (EP/I004475/1), Diamond Light Source, UK and HFML, Nijmegen.

Processing of high-temperature superconductors at high strain rates

International Nuclear Information System (INIS)

Mamalis, A.G.; Pantazsopoulos, G.; Manolakos, D.E.; Szalay, A.

2000-01-01

This new book provides, for the first time, a systematic, unified presentation of all steps in the processing of high-temperature superconductor materials, ranging from synthesis of various systems to fabrication and industrial applications. Also covered are characterization techniques and current directions in research and development. The authors are leading specialists who bring to this new book their many years of experience in research, education and industrial engineering work in superconductor materials. This book is primarily focused on the bulk-fabrication techniques of high-temperature ceramic superconducting components, especially on the combination of dynamic powder-consolidation and subsequent deformation processing. The properties of these ceramics, which are difficult-to-form materials by applying conventional techniques, are combined for the net-shape manufacturing of such components for the construction of HTS deviceshor e llipsis. However, very important topics such as superconducting structures, chemical synthesis, film fabrication and characterization techniques are also reviewedhor e llipsis to provide a complete, comprehensive view of superconductors engineering

Production of no-carrier-added {sup 123}I via heavy-ion activation of natural antimony oxide

Energy Technology Data Exchange (ETDEWEB)

Maji, S. [The Univ. of Burdwan (India). Dept. of Chemistry; Lahiri, S. [Saha Institute of Nuclear Physics, Kolkata (India). Chemical Sciences Div.

2007-07-01

Activation of natural Sb{sub 2}O{sub 3} with 48 MeV {sup 7}Li{sup 3+} beam results in the formation of no-carrier-added {sup 123}I in the matrix along with the radionuclides {sup 123,125}Xe and {sup 122}Sb. The {sup 123}I yield amounts to about 400 kBq/{mu}Ah and the radionuclidic impurity of {sup 124}I to {proportional_to}1.2% of {sup 123}I. Attempts to separate no-carrier-added iodine from bulk antimony target involved liquid-liquid extraction with TOA and HDEHP as well as precipitation of Sb{sub 2}S{sub 3} with thioacetamide. The precipitation technique was found to be the most effective for quantitative separation of {sup 123}I from the bulk antimony oxide target. (orig.)

Thermal behaviour of the ESR Relaxation time in slightly dirty superconductors

International Nuclear Information System (INIS)

Schwachheim, G.; Machado, S.F.; Tsallis, C.

1978-07-01

The thermal behaviour of the ESR relaxation rate in slightly dirty superconductors is discussed for both exchange and spin-orbit interactions between the conduction electrons and the impurities. The sensibility to the electronic density of states is exhibited by using, in a modified BCS framework, an heuristic analytic form which avoids two of three defects of a previous similar treatment. The sudden increase (decrease) of the relaxation rate immediately below the critical temperature for the exchange (spin-orbit) case is confirmed. Reasonable agreement with experimental data in LaRu 2 ; Gd is obtained [pt

A review of finite size effects in quasi-zero dimensional superconductors.

Science.gov (United States)

Bose, Sangita; Ayyub, Pushan

2014-11-01

Quantum confinement and surface effects (SEs) dramatically modify most solid state phenomena as one approaches the nanometer scale, and superconductivity is no exception. Though we may expect significant modifications from bulk superconducting properties when the system dimensions become smaller than the characteristic length scales for bulk superconductors-such as the coherence length or the penetration depth-it is now established that there is a third length scale which ultimately determines the critical size at which Cooper pairing is destroyed. In quasi-zero-dimensional (0D) superconductors (e.g. nanocrystalline materials, isolated or embedded nanoparticles), one may define a critical particle diameter below which the mean energy level spacing arising from quantum confinement becomes equal to the bulk superconducting energy gap. The so-called Anderson criterion provides a remarkably accurate estimate of the limiting size for the destabilization of superconductivity in nanosystems. This review of size effects in quasi-0D superconductors is organized as follows. A general summary of size effects in nanostructured superconductors (section 1) is followed by a brief overview of their synthesis (section 2) and characterization using a variety of techniques (section 3). Section 4 reviews the size-evolution of important superconducting parameters-the transition temperature, critical fields and critical current-as the Anderson limit is approached from above. We then discuss the effect of thermodynamic fluctuations (section 5), which become significant in confined systems. Improvements in fabrication methods and the increasing feasibility of addressing individual nanoparticles using scanning probe techniques have lately opened up new directions in the study of nanoscale superconductivity. Section 6 reviews both experimental and theoretical aspects of the recently discovered phenomena of 'parity effect' and 'shell effect' that lead to a strong, non-monotonic size

Simple top-down preparation of magnetic Bi_0.9Gd_0.1Fe_1−xTi_xO₃ nanoparticles by ultrasonication of multiferroic bulk material

DEFF Research Database (Denmark)

Basith, M. A.; Ngo, Duc-The; Quader, A.

2014-01-01

We present a simple technique to synthesize ultrafine nanoparticles directly from bulk multiferroic perovskitepowder. The starting materials, which were ceramic pellets of the nominal compositions Bi0.9Gd0.1-Fe1−xTixO3 (x = 0.00–0.20), were prepared initially by a solid state reaction technique, ...

Low-temperature rapid synthesis and superconductivity of Fe-based oxypnictide superconductors.

Science.gov (United States)

Fang, Ai-Hua; Huang, Fu-Qiang; Xie, Xiao-Ming; Jiang, Mian-Heng

2010-03-17

Fe-based oxypnictide superconductors were successfully synthesized at lower reaction temperatures and with shorter reaction times made possible by starting with less stable compounds, which provide a larger driving force for reactions. Using ball-milled powders of intermediate compounds, phase-pure superconductors with T(c) above 50 K were synthesized at 1173 K in 20 min. This method is particularly advantageous for retaining F, a volatile dopant that enhances superconductivity. Bulk superconductivity and high upper critical fields up to 392 T in Sm(0.85)Nd(0.15)FeAsO(0.85)F(0.15) were demonstrated.

Growth of layered superconductor β-PdBi{sub 2} films using molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Denisov, N.V., E-mail: denisov@iacp.dvo.ru [Institute of Automation and Control Processes FEB RAS, 5 Radio Street, 690041 Vladivostok (Russian Federation); Matetskiy, A.V.; Tupkalo, A.V. [Institute of Automation and Control Processes FEB RAS, 5 Radio Street, 690041 Vladivostok (Russian Federation); Zotov, A.V. [Institute of Automation and Control Processes FEB RAS, 5 Radio Street, 690041 Vladivostok (Russian Federation); School of Natural Sciences, Far Eastern Federal University, 690950 Vladivostok (Russian Federation); Department of Electronics, Vladivostok State University of Economics and Service, 690600 Vladivostok (Russian Federation); Saranin, A.A. [Institute of Automation and Control Processes FEB RAS, 5 Radio Street, 690041 Vladivostok (Russian Federation); School of Natural Sciences, Far Eastern Federal University, 690950 Vladivostok (Russian Federation)

2017-04-15

Highlights: • Bulk β-PdBi{sub 2} is layered material with advanced properties of topological superconductor. • We present a method for growing β-PdBi{sub 2} films of a desired thickness. • Method utilizes MBE growth of β-PdBi{sub 2}, using Bi(111) film on Si(111) as a template. • Electronic and superconducting properties of the films are similar to those of bulk β-PdBi{sub 2}. - Abstract: Bulk β-PdBi{sub 2} layered material exhibits advanced properties and is supposed to be probable topological superconductor. We present a method based on molecular beam epitaxy that allows us to grow β-PdBi{sub 2} films from a single β-PdBi{sub 2} triple layer up to the dozens of triple layers, using Bi(111) film on Si(111) as a template. The grown films demonstrate structural, electronic and superconducting properties similar to those of bulk β-PdBi{sub 2} crystals. Ability to grow the β-PdBi{sub 2} films of desired thickness opens the promising possibilities to explore fascinating properties of this advanced material.

The magnetic order of GdMn₂Ge₂ studied by neutron diffraction and x-ray resonant magnetic scattering.

Science.gov (United States)

Granovsky, S A; Kreyssig, A; Doerr, M; Ritter, C; Dudzik, E; Feyerherm, R; Canfield, P C; Loewenhaupt, M

2010-06-09

The magnetic structure of GdMn₂Ge₂ (tetragonal I4/mmm) has been studied by hot neutron powder diffraction and x-ray resonant magnetic scattering techniques. These measurements, along with the results of bulk experiments, confirm the collinear ferrimagnetic structure with moment direction parallel to the c-axis below T(C) = 96 K and the collinear antiferromagnetic phase in the temperature region T(C) < T < T(N) = 365 K. In the antiferromagnetic phase, x-ray resonant magnetic scattering has been detected at Mn K and Gd L₂ absorption edges. The Gd contribution is a result of an induced Gd 5d electron polarization caused by the antiferromagnetic order of Mn-moments.

Levitation force and magnetization in bulk and thin film high Tc superconductors

International Nuclear Information System (INIS)

Riise, A.B

1998-04-01

The authors present high-resolution measurements of the repulsive vertical force and its associated stiffness between a Nd-B-Fe magnet and a YBa 2 Cu 3 O 7-δ superconductor in cylindrical geometry. The results are compared with theoretical predictions. The calculations are based on a model in which the superconductor is assumed to be either a sintered granular material or consisting of grains embedded in a nonactive matrix so that only intragranular currents are important. The critical state model is applied to each grain individually and closed form expressions for both vertical force F z and stiffness are obtained in a configuration with cylindrical symmetry. The model explains all features of the experimental results in a consistent way. A good quantitative agreement has been obtained using only three adjustable parameters. Several central aspects of the phenomenon of magnetic levitation with high-T c superconductors are presented. High-resolution measurements are made of the repulsive vertical force and its associated stiffness as well as the horizontal stabilizing force and the stiffness governing lateral vibrations. The results obtained at 77 K using a granular YBa 2 Cu 3 O 7-δ sample and Nd-Fe-B magnet in a rectangular levitation configuration are compared with theoretical predictions. The calculations, which are based on the critical state model with the assumption that it applies to the grins individually, give closed-form expressions for all the measured quantities. It is concluded that the present model explains all features of the observations in a consistent way. Using only three adjustable parameters a good agreement exists also at a quantitative level. Experimental studies and theoretical modelling of the levitation force on a permanent magnet placed above a superconducting thin film are offered. It is shown that measurements of the levitation force is a simple and precise method to determine the critical current density in thin films

Experimental consequences of predicted charge rigidity of superconductors

Energy Technology Data Exchange (ETDEWEB)

Hirsch, J.E., E-mail: jhirsch@ucsd.edu [Department of Physics, University of California, San Diego, La Jolla, CA 92093-0319 (United States)

2012-08-15

The theory of hole superconductivity predicts that in superconductors the charged superfluid is about a million times more rigid than the normal electron fluid. We point out that this physics should give rise to large changes in the bulk and surface plasmon dispersion relations of metals entering the superconducting state, that have not yet been experimentally detected and would be in stark contradiction with the expected behavior within conventional BCS-London theory. We also propose that this explains the puzzling experimental observations of Avramenko et al. on electron sound propagation in superconductors and the puzzling experiments of de Heer et al. detecting large electric dipole moments in small metal clusters, as well as the Tao effect on aggregation of superconducting microparticles in an electric field. Associated with the enhanced charge rigidity is a large increase in the electric screening length of superconductors at low temperatures that has not yet been experimentally detected. The physical origin of the enhanced charge rigidity and its relation to other aspects of the theory of hole superconductivity is discussed.

Passivation of high temperature superconductors

Science.gov (United States)

Vasquez, Richard P. (Inventor)

1991-01-01

The surface of high temperature superconductors such as YBa2Cu3O(7-x) are passivated by reacting the native Y, Ba and Cu metal ions with an anion such as sulfate or oxalate to form a surface film that is impervious to water and has a solubility in water of no more than 10(exp -3) M. The passivating treatment is preferably conducted by immersing the surface in dilute aqueous acid solution since more soluble species dissolve into the solution. The treatment does not degrade the superconducting properties of the bulk material.

Ceramic superconductors II

International Nuclear Information System (INIS)

Yan, M.F.

1988-01-01

This volume compiles papers on ceramic superconductors. Topics include: structural patterns in High-Tc superconductors, phase equilibria of barium oxide superconductors, localized electrons in tetragonal YBa/sub 2/Cu/sub 3/O/sub 7-δ/, lattice and defect structure and properties of rare earth/alkaline earth-copper-oxide superconductors, alternate candidates for High-Tc superconductors, perovskite-structure superconductors; superconductive thin film fabrication, and superconductor/polymer composites

The effect of processing parameters during heat treatment of bulk high-T(sub c) superconductors

Science.gov (United States)

Cha, Y. S.; Dorris, S. E.; Hull, J. R.; Poeppel, R. B.

1991-04-01

Plastic extrusion is a promising method for producing the long lengths of high-Tc superconductor that will be necessary to meet many potential applications. A crucial phase of the extrusion method is removal of organic constituents. Incomplete removal can leave residual carbon at grain boundaries, which can adversely affect the superconducting properties, whereas excessively rapid removal of the organics can cause the extruded superconductor to disintegrate completely. In this paper, we analyze the effects of the following aspects of organics removal, as they apply to the firing of extruded YBa2Cu3O(x) coils: (1) total pressure in the furnace, (2) oxygen flow, (3) heat conduction, and (4) diffusion of volatile components during removal of organics.

Magnetic and superconducting phase diagram of Nb/Gd/Nb trilayers

Science.gov (United States)

Khaydukov, Yu. N.; Vasenko, A. S.; Kravtsov, E. A.; Progliado, V. V.; Zhaketov, V. D.; Csik, A.; Nikitenko, Yu. V.; Petrenko, A. V.; Keller, T.; Golubov, A. A.; Kupriyanov, M. Yu.; Ustinov, V. V.; Aksenov, V. L.; Keimer, B.

2018-04-01

We report on a study of the structural, magnetic, and superconducting properties of Nb (25 nm ) /Gd (df) /Nb (25 nm ) hybrid structures of a superconductor/ ferromagnet (S/F) type. The structural characterization of the samples, including careful determination of the layer thickness, was performed using neutron and x-ray scattering with the aid of depth-sensitive mass spectrometry. The magnetization of the samples was determined by superconducting quantum interference device magnetometry and polarized neutron reflectometry, and the presence of magnetic ordering for all samples down to the thinnest Gd(0.8 nm) layer was shown. The analysis of the neutron spin asymmetry allowed us to prove the absence of magnetically dead layers in junctions with Gd interlayer thickness larger than one monolayer. The measured dependence of the superconducting transition temperature Tc(df) has a damped oscillatory behavior with well-defined positions of the minimum at df=3 nm and the following maximum at df=4 nm, in qualitative agreement with prior work [J. S. Jiang et al., Phys. Rev. B 54, 6119 (1996), 10.1103/PhysRevB.54.6119]. We use a theoretical approach based on the Usadel equations to analyze the experimental Tc(df) dependence. The analysis shows that the observed minimum at df=3 nm can be described by the so-called zero to π phase transitions of highly transparent S/F interfaces with a superconducting correlation length ξf≈4 nm in Gd. This penetration length is several times higher than for strong ferromagnets like Fe, Co, and Ni, thus simplifying the preparation of S/F structures with df˜ξf which are of topical interest in superconducting spintronics.

Magnetic uni- and tri-axial grain-orientation in superconductors with layered structures

International Nuclear Information System (INIS)

Horii, S.; Yamaki, M.; Ogino, H.; Maeda, T.; Shimoyama, J.

2010-01-01

We report the grain-orientation effects under a modulated rotation magnetic field for Y-based cuprate superconductors and LaFeAsO (La1111). Tri-axial orientation has been successfully achieved only for orthorhombic Y 2 Ba 4 Cu 7 O y and YBa 2 Cu 4 O 8 powders without a twin microstructure, while separation of three crystallographic axes could not be observed in twinned YBa 2 Cu 3 O y (Y123) and tetragonal La1111 powders. The morphology of grains, in addition to the symmetry of crystal structures, seriously affects the degrees of tri-axial orientation, which means that the control of twin microstructures is required for the tri-axial magnetic orientation in Y123.

High performance batch production of LREBa2Cu3Oy using novel thin film Nd-123 seed

International Nuclear Information System (INIS)

Muralidhar, M.; Suzuki, K.; Fukumoto, Y.; Ishihara, A.; Tomita, M.

2011-01-01

A batch production for fabrication of LREBa 2 Cu 3 O y (LRE: Sm, Gd, NEG) 'LRE-123' pellets are developed in air and Ar-1% O 2 using a novel thin film Nd-123 seeds grown on MgO crystals. The SEM and XRD results conformed that the quality and orientation of the seed crystals are excellent. On the other hand, new seeds can withstand temperatures >1100 deg. C, as a result, the cold seeding process was applied even to grow Sm-123 material in Air. The trapped field observed in the best 45 mm single-grain puck of Gd-123 was in the range of 1.35 T and 0.35 T at 77.3 K and 87.3 K, respectively. The average trapped field at 77.3 K in the 24 mm diameter NEG-123 samples batch lies between 0.9 and 1 T. The maximum trapped field of 1.2 T was recorded at the sample surface. Further, the maximum trapped field of 0.23 T at 77 K was recorded in a sample with 16 mm diameter of Sm-123 with 3 mol% BaO 2 addition. As a result we made more then 130 single grain pucks within a couple of months. Taking advantage of the single grain batch processed material, we constructed self-made chilled levitation disk, which was used on the open day of railway technical research Institute. More then 150 children stood on the levitation disk and revel the experience of levitation. The present results prove that a high-performance good-quality class of LREBa 2 Cu 3 O y material can be made by using a novel thin film Nd-123 seeds.

Influence of lateral displacement on the levitation performance of a magnetized bulk high-T{sub c} superconductor magnet

Energy Technology Data Exchange (ETDEWEB)

Liu, W., E-mail: tonny-violet@163.com [College of Nuclear Technology and Automation Engineering, Chengdu University of Technology, Chengdu 610059 (China) and Applied Superconductivity Laboratory, Southwest Jiaotong University, Chengdu 610031 (China); Wang, J.S.; Ma, G.T.; Zheng, J. [Applied Superconductivity Laboratory, Southwest Jiaotong University, Chengdu 610031 (China); State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu 610031 (China); National Laboratory of Rail Transit, Chengdu, 610031 (China); Tuo, X.G.; Li, L.L. [College of Nuclear Technology and Automation Engineering, Chengdu University of Technology, Chengdu 610059 (China); Ye, C.Q.; Liao, X.L. [Applied Superconductivity Laboratory, Southwest Jiaotong University, Chengdu 610031 (China); National Laboratory of Rail Transit, Chengdu, 610031 (China); Wang, S.Y. [Applied Superconductivity Laboratory, Southwest Jiaotong University, Chengdu 610031 (China); State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu 610031 (China); National Laboratory of Rail Transit, Chengdu, 610031 (China)

2012-03-15

Compared with the permanent magnet, the magnetized bulk high-T{sub c} superconductor magnet (MBSCM) can trap higher magnetic field due to its strong flux pinning ability, so it is a good candidate to improve the levitation performance of high-T{sub c} superconductive (HTS) maglev system. The trapped magnetic flux of a MBSCM is sustained by the inductive superconducting current produced by the magnetizing process and is susceptible to the current intensity as well as configuration. In the HTS maglev system, the lateral displacement is an important process to change the superconducting current within a MBSCM and then affects its levitation performance, which is essential for the traffic ability in curve-way, the loading capacity of lateral impact and so on. The research about influence of lateral displacement on the levitation performance of MBSCM is necessary when MBSCM is applied on the HTS maglev vehicle. The experimental investigations about the influence of lateral displacement on the levitation performance of a MBSCM with different trapped fluxes and applied fields are processed in this article. The analyses and conclusions of this article are useful for the practical application of MBSCM in HTS maglev system.

The superconductor

International Nuclear Information System (INIS)

Lad, J.K.

1979-01-01

Techniques for fabrication of a few important superconductors like Nb, Ti and Nb 3 Sn are described. Copper or bronze or both can be used as a matrix in the superconductor. Current densities obtained for different ratios of copper to superconductor are studied. The specifications of multi-filament Nb 3 Sn superconductors are given. The relative merits of the two superconductors are discussed. The temperature range obtained is approximately 3 0 K and a magnetic field of 9T(tesla) can be achieved. (A.K.)

Stiffness Evaluation of High Temperature Superconductor Bearing Stiffness for 10 kWh Superconductor Flywheel Energy Storage System

International Nuclear Information System (INIS)

Park, B. J.; Jung, S. Y.; Lee, J. P.; Park, B. C.; Kim, C. H.; Han, S. C.; Du, S. G.; Han, Y. H.; Sung, T. H.

2009-01-01

A superconductor flywheel energy storage(SFES) system is mainly act an electro-mechanical battery which transfers mechanical energy into electrical form and vice versa. SFES system consists of a pair of non-contacting High Temperature Superconductor (HTS) bearings with a very low frictional loss. But it is essential to design an efficient HTS bearing considering with rotor dynamic properties through correct calculation of stiffness in order to support a huge composite flywheel rotor with high energy storage density. Static properties of HTS bearings provide data to solve problems which may occur easily in a running system. Since stiffness to counter vibration is the main parameter in designing an HTS bearing system, we investigate HTS bearing magnetic force through static properties between the Permanent Magnet(PM) and HTS. We measured axial / radial stiffness and found bearing stiffness can be easily changed by activated vibration direction between PM and HTS bulk. These results are used to determine the optimal design for a 10 kWh SFES.

Scanning tunneling microscopy and spectroscopy studies of the heavy-electron superconductor TlNi2Se2

Science.gov (United States)

Wilfert, Stefan; Schmitt, Martin; Schmidt, Henrik; Mauerer, Tobias; Sessi, Paolo; Wang, Hangdong; Mao, Qianhui; Fang, Minghu; Bode, Matthias

2018-01-01

We report on the structural and superconducting electronic properties of the heavy-electron superconductor TlNi2Se2 . By using a variable-temperature scanning tunneling microscopy (VT-STM) the coexistence of (√{2 }×√{2 }) R 45∘ and (2 ×1 ) surface reconstructions is observed. Similar to earlier observations on the "122" family of Fe-based superconductors, we find that their respective surface fraction strongly depends on the temperature during cleavage, the measurement temperature, and the sample's history. Cleaving at low temperature predominantly results in the (√{2 }×√{2 }) R 45∘ -reconstructed surface. A detailed analysis of the (√{2 }×√{2 }) R 45∘ -reconstructed domains identifies (2 ×1 ) -ordered dimers, tertramers, and higher order even multimers as domain walls. Higher cleaving temperatures and the warming of low-temperature-cleaved samples increases the relative weight of the (2 ×1 ) surface reconstruction. By slowly increasing the sample temperature Ts inside the VT-STM we find that the (√{2 }×√{2 }) R 45∘ surface reconstructions transforms into the (2 ×1 ) structure at Ts=123 K. We identify the polar nature of the TlNi2Se2 (001) surface as the most probable driving mechanism of the two reconstructions, as both lead to a charge density ρ =0.5 e- , thereby avoiding divergent electrostatic potentials and the resulting "polar catastrophe." Low-temperature scanning tunneling spectroscopy (STS) performed with normal metal and superconducting probe tips shows a superconducting gap which is best fit with an isotropic s wave. We could not detect any correlation between the local surface reconstruction, suggesting that the superconductivity is predominantly governed by TlNi2Se2 bulk properties. Correspondingly, temperature- and field-dependent data reveal that both the critical temperature and critical magnetic field are in good agreement with bulk values obtained earlier from transport measurements. In the superconducting state

Thermal fluctuations in the classical superconductor Nb3Sn from high-resolution specific-heat measurements

International Nuclear Information System (INIS)

Lortz, Rolf; Wang Yuxing; Junod, Alain; Toyota, Naoki

2007-01-01

The range of thermal fluctuations in 'classical' bulk superconductors is extremely small and especially in low-fields hardly experimentally accessible. With a new type of calorimeter we were able to detect a tiny lambda anomaly in the specific-heat of the superconductor Nb 3 Sn within a narrow temperature range around the H c2 line. We show that the evolution of the anomaly as a function of magnetic field follows scaling laws expected in the presence of critical thermal fluctuations

About the investigation of the ultrasonic absorption in intermediate states of superconductors

International Nuclear Information System (INIS)

Shepelev, A.G.

2003-01-01

Investigation of intermediate state in the bulk of superconductors are surveyed. Consideration is given to a previous attempt of eliminating edge effects in the ultrasonic investigation of intermediate states of pure gallium and molybdenum;it is demonstrated that those results are in strong contradiction with Landau's intermediate-state theory

Gd-Ni-Si system

International Nuclear Information System (INIS)

Bodak, O.I.; Shvets, A.F.

1983-01-01

By X-ray phase analysis method isothermal cross section of phase diagram of the Gd-Ni-Si system at 870 K is studied. The existence of nine previously known compounds (GdNisub(6.72)Sisub(6.28), GdNi 10 Si 2 , GdNi 5 Si 3 , GdNi 4 Si, GdNi 2 Si 2 , GdNiSi 3 , GdNiSi 2 , Gd 3 Ni 6 Si 2 and GdNiSi) is confirmed and three new compounds (GdNisub(0.2)Sisub(1.8), Gdsub(2)Nisub(1-0.8)Sisub(1-1.2), Gd 5 NiSi 4 ) are found. On the base of Gd 2 Si 3 compound up to 0.15 at. Ni fractions, an interstitial solid solution is formed up to 0.25 at Ni fractions dissolution continues of substitution type. The Gd-Ni-Si system is similar to the Y-Ni-Si system

Single Crystal Synthesis and STM Studies of High Temperature Superconductors

Science.gov (United States)

Barrientos, Alfonso

1997-01-01

This is a final report for the work initiated in September of 1994 under the grant NAG8-1085 - NASA/OMU, on the fabrication of bulk and single crystal synthesis, specific heat measuring and STM studies of high temperature superconductors. Efforts were made to fabricate bulk and single crystals of mercury based superconducting material. A systematic thermal analysis on the precursors for the corresponding oxides and carbonates were carried out to synthesized bulk samples. Bulk material was used as seed in an attempt to grow single crystals by a two-step self flux process. On the other hand bulk samples were characterized by x-ray diffraction, electrical resistivity and magnetic susceptibility, We studied the specific heat behavior in the range from 80 to 300 K. Some preliminary attempts were made to study the atomic morphology of our samples. As part of our efforts we built an ac susceptibility apparatus for measuring the transition temperature of our sintered samples.

Gd3+-ESR and magnetic susceptibility of GdCu4Al8 and GdMn4Al8

International Nuclear Information System (INIS)

Coldea, R.; Coldea, M.; Pop, I.

1994-01-01

Gd ESR of GdCu 4 Al 8 and GdMn 4 Al 8 and magnetic susceptibility of GdCu 4 Al 8 , GdMn 4 Al 8 , and YMn 4 Al 8 were measured in the temperature range of 290K--460K and 90K--1050K, respectively. The occurrence of the Mn moment in YMn 4 Al 8 and GdMn 4 Al 8 is strongly correlated with the critical value of d∼2.6 angstrom of the Mn-Mn distance below which the Mn moment is not stable. The experimental data for GdMn 4 Al 8 , compared with the data for the isostructural compounds GdCu 4 Al 8 and YMn 4 Al 8 , show that near the critical value of d, the existence of Mn moment depends not only on the value of d, but also on the local magnetic surroundings. It has been revealed that the magnetic character of Mn moment in YMn 4 Al 8 and GdMn 4 Al 8 changes from an itinerant electron type to a local-moment type with increasing temperature

Briefing on superconductor developments

International Nuclear Information System (INIS)

Larbalestier, D.

1987-01-01

In this paper, the author covers the technology of the new oxide superconductors and how they might relate to the existing superconductors. He discusses old-fashioned superconductors; the material science of superconductors; the new oxide superconductors; and the future of oxide superconductors. 13 figures, 1 table

Studies of alloy structures and properties. Annual summary report, December 1, 1976--December 1, 1977

International Nuclear Information System (INIS)

Duwez, P.

1977-01-01

Brief summaries of research activities in the following areas are given: superconductivity to ferromagnetism in amorphous Gd--La--Au alloys; magnetic regimes in amorphous Ni--Fe--P--B alloys; electronic and magnetic properties of amorphous Fe--P--B alloys; critical phenomena and magnetic properties of amorphous gadolinium based ferromagnets; Kondo effect, spin correlations, and superconductivity in amorphous alloys doped with magnetic impurities; flux pinning by crystalline phase precipitates embedded in an amorphous superconducting matrix; kinetics of crystallization of amorphous alloys; properties of the flux lattice in amorphous superconductors; low temperature calorimeter; low temperature heat capacity of metastable superconductors; thermal relaxation effects and crystallization of amorphous alloys; fundamental studies of amorphous superconductors using superconductive tunneling; low temperature calorimetry of bulk amorphous metals; and mictomagnetism in amorphous alloys

Pre-fabricated nanorods in RE–Ba–Cu–O superconductors

International Nuclear Information System (INIS)

Khatri, N D; Majkic, G; Shi, T; Selvamanickam, V; Chen, Y

2013-01-01

Pre-fabrication of metallic nanorods on biaxially textured templates has been explored in this study to introduce flux pinning centers in RE–Ba–Cu–O (REBCO, RE =rare earth) based superconductors. Pt nanorods were deposited by an electron beam assisted deposition method on LaMnO 3 -capped biaxially textured IBAD-(ion beam assisted deposition) substrates. Well-controlled nanorods with varying diameter (50–120 nm), length (up to 1 μm), orientation and unit cell size were grown over an area of 120–150 μm 2 . The nanorod-decorated samples were then deposited with Gd–Y–Ba–Cu–O ((Gd, Y)BCO) by metal organic chemical vapor deposition (MOCVD). The Pt nanorods remain in their positions during MOCVD and become embedded in the (Gd, Y)BCO matrix, although they suffer creep-induced shape deformation due to exposure to elevated temperature. Higher unit cell size, longer nanorods, and nanorods oriented at an angle to the substrate normal adversely affect the epitaxy of the (Gd, Y)BCO film due to formation of a-axis grains. The observed current-carrying capacity of the Pt nanorod sample is lower than its corresponding reference sample without any nanorods and processed under identical conditions, but it decreases at a slower rate with increasing magnetic field. Potential routes to improve the performance while retaining the desirable characteristics of controlled nanorod direction and density are discussed. (paper)

Magnetic and transport properties of amorphous ferro magnetic Gd--Au, Gd--Ni and Gd--Co alloys obtained by splat-cooling

International Nuclear Information System (INIS)

Durand, J.; Poon, S.J.

1977-06-01

We present the results of magnetization and transport measurements on the amorphous Gd 80 Au 20 , Gd 68 Ni 32 and Gd 67 Co 33 alloys over a temperature range of 1.8 to 300 0 K in fields up to 75 kOe. These ferromagnetic alloys obtained by splat-cooling have Curie temperatures T/sub c/ of 150, 125 and 175 0 K, respectively. The saturation moment per Gd atom extrapolated to 0 0 K is estimated to be 7 +- 0.1 μ/sub B/. The exchange integrals for Gd-Au and Gd-Ni are determined from the value of T/sub c/ and from the temperature dependence of the saturation magnetization. The zero-field resistivity for Gd-Ni and Gd-Co exhibits maxima around T/sub c/. We present some preliminary results of magnetoresistivity measurements with applied field parallel and perpendicular to the foil plane. The anisotropy is in-plane for Gd-Co. For the Gd-Au and Gd-Ni alloys, there is no well-defined easy axis

Critical current density and wire fabrication of high-TC superconductors

International Nuclear Information System (INIS)

Schlabach, T.D.; Jin, S.; Sherwood, R.C.; Tiefel, T.H.

1989-01-01

In this paper, some of the recent investigations of wire fabrication techniques and critical current behavior in high T c superconductors will be reviewed. In spite of the tremendous interest and research effort, the progress toward major applications of the bulk high-temperature superconductors has been impeded by, among other thins, the low critical currents and their severe deterioration in weak magnetic fields. Significant advances, however, have been made in understanding the causes of the problem as well as in improving the current-carrying capacity through proper microstructural control such as the melt-textured-growth in Y-Ba-Cu-O. The low density of effective flux-pinning sites in bulk Y-Ba-Cu-O limits J c at 77K in high magnetic fields to about 10 4 A/cm 2 even in the absence of weak links. Magnetization measurements on Bi-Sr-Ca-Cu-O and Tl-Ba-Ca-Cu-O at 77K by various researchers indicate even weaker flux pinning capabilities in these materials than in Y-Ba-Cu-O. The challenge in the future is to obtain suitable flux-pinning defects by choosing the right processing and chemistry changes

Relaxation and pinning in spark-plasma sintered MgB.sub.2./sub. superconductor

Czech Academy of Sciences Publication Activity Database

Jirsa, Miloš; Rameš, Michal; Koblischka, M.R.; Koblischka-Veneva, A.; Berger, K.; Douine, B.

2016-01-01

Roč. 29, č. 2 (2016), 1-7, č. článku 025006. ISSN 0953-2048 Institutional support: RVO:68378271 Keywords : bulk MgB 2 superconductor * magnetic properties * magnetic relaxation * critical currents * pinning force density Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.878, year: 2016

The effect of nano-size ZrO2 powder addition on the microstructure and superconducting properties of single-domain Y-Ba-Cu-O bulk superconductors

International Nuclear Information System (INIS)

Iida, K; Babu, N H; Reddy, E S; Shi, Y-H; Cardwell, D A

2005-01-01

The effect of nano-size ZrO 2 powder addition on the microstructure and superconducting properties of Y-Ba-Cu-O single grain bulk superconductors has been investigated. Significant pushing phenomena of Y 2 BaCuO 5 (Y-211) particles, particularly in the c growth sector, were observed even with a small amount of ZrO 2 added to the precursor powder. An increase in Y-211 particle pushing was observed with increasing ZrO 2 content, leading to an inhomogeneous bulk microstructure. In addition, a growth cycle consisting of a Y-211 free layer-porous narrow layer-Y-211 high concentration layer was observed for samples prepared with 0.25 wt% ZrO 2 in both the a and c growth sectors. The extent of the growth of single grain Y-Ba-Cu-O (YBCO) decreased with increasing ZrO 2 content due to increased pushing of Y-211 particles towards molten liquid. The superconducting transition temperature, T c , of the ZrO 2 containing YBCO samples was sharp but depressed slightly (by up to 1 K) compared with an undoped YBCO grain, indicating a relative insensitivity of T c to ZrO 2 content. Finally, the sensitivity of critical current density, J c , to applied magnetic field in large grain bulk YBCO containing ZrO 2 was observed to depend critically on position due to the inhomogeneous sample microstructure

Radioluminescence studies of colloidal oleate-capped β-Na(Gd,Lu)F4:Ln3+ nanoparticles (Ln = Ce, Eu, Tb).

Science.gov (United States)

Cooper, Daniel R; Capobianco, John A; Seuntjens, Jan

2018-04-26

We report on the synthesis, characterization, and radioluminescence quantification of several new varieties of nanoparticles with the general composition β-NaLnF4, incorporating known luminescent activator/sensitizer pairs. Using Monte Carlo modeling to complement luminescence measurements, we have calculated the radioluminescence yields and intrinsic conversion efficiencies of colloidally-dispersed nanoparticles by comparison to an organic liquid scintillator. While five of the compositions had low to modest radioluminescence yields relative to bulk materials, colloidal β-Na(Lu0.65Gd0.2Tb0.15)F4 displayed a strong output of 39 460 photons per MeV absorbed, comparable to some of the best non-hygroscopic bulk crystal scintillators and X-ray phosphors such as Gd2O2S:Tb. Measurements of β-Na(Lu0.65Gd0.2Tb0.15)F4 powder samples revealed persistent luminescence as well as stable charge trapping, warranting further investigation.

Theory of coherent c-axis Josephson tunneling between layered superconductors

International Nuclear Information System (INIS)

Arnold, G. B.; Klemm, R. A.

2000-01-01

We calculate exactly the Josephson current for c-axis coherent tunneling between two layered superconductors, each with internal coherent tight-binding intra- and interlayer quasiparticle dispersions. Our results also apply when one or both of the superconductors is a bulk material, and include the usually neglected effects of surface states. For weak tunneling, our results reduce to our previous results derived using the tunneling Hamiltonian. Our results are also correct for strong tunneling. However, the c-axis tunneling expressions of Tanaka and Kashiwaya are shown to be incorrect in any limit. In addition, we consider the c-axis coherent critical current between two identical layered superconductors twisted an angle φ 0 about the c axis with respect to each other. Regardless of the order-parameter symmetry, our coherent tunneling results using a tight-binding intralayer quasiparticle dispersion are inconsistent with the recent c-axis twist bicrystal Bi 2 Sr 2 CaCu 2 O 8+δ twist junction experiments of Li et al. [Li et al., Phys. Rev. Lett. 83, 4160 (1999)]. (c) 2000 The American Physical Society

Cryogenic milling for the fabrication of high J{sub c} MgB{sub 2} bulk superconductors

Energy Technology Data Exchange (ETDEWEB)

Kim, D. N.; Kang, M. O.; Park, H. W. [Korea University of Technology and Education, Cheonan (Korea, Republic of); Jun, B. H.; Kim, C. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2017-06-15

Cryogenic milling which is a combined process of low-temperature treatment and mechanical milling was applied to fabricate high critical current density (J{sub c}) MgB{sub 2} bulk superconductors. Liquid nitrogen was used as a coolant, and no solvent or lubricant was used. Spherical Mg (6-12 μm, 99.9 % purity) and plate-like B powder (⁓ 1 μm, 97 % purity) were milled simultaneously for various time periods (0, 2, 4, 6 h) at a rotating speed of 500 rpm using ZrO{sub 2} balls. The (Mg{sup +2B}) powders milled were pressed into pellets and heat-treated at 700°C for 1 h in flowing argon. The use of cryomilled powders as raw materials promoted the formation reaction of superconducting MgB{sub 2}, reduced the grain size of MgB{sub 2}, and suppressed the formation of impurity MgO. The superconducting critical temperature (T{sub c}) of MgB{sub 2} was not influenced as the milling time (t) increased up to 6 h. Meanwhile, the critical current density (J{sub c}) of MgB{sub 2} increased significantly when t increased to 4 h. When t increased further to 6 h, however, Jc decreased. The J{sub c} enhancement of MgB{sub 2} by cryogenic milling is attributed to the formation of the fine grain MgB{sub 2} and a suppression of the MgO formation.

Effect of silver doping on infrared reflectance and Tc of superconducting GdBa2Cu(1 - x)3Ag3xO7

International Nuclear Information System (INIS)

Memon, A.; Khan, M.N.; Al-Dallal, S.; Tanner, D.B.; Porter, C.D.

1990-01-01

This paper reports on infrared reflectance of GdBa 2 Cu(1 - x) 3 Ag 3x O 7 ceramic superconductor with the composition of x = 0.025 and 0.05 performed in the frequency range of 100--5000 cm -1 . All the infrared active phonon modes allowed by the selection rules were observed in the reflection spectra of these compounds. The optical conductivity as calculated from K--K analysis further confirms the existence of these optical phonons. Besides the increase of the reflectivity in the silver doped samples, an extra phonon mode is observed, which is normally not seen at room temperature reflectance of GdBa 2 Cu 3 O 7 compounds. The four probe resistivity measurement show zero resistance at 88 K for x = 0, and 78 K for x = 0.025 in GdBa 2 Cu(1 - x) 3 Ag 3x O 7 compound

Thermal fluctuations in the classical superconductor Nb{sub 3}Sn from high-resolution specific-heat measurements

Energy Technology Data Exchange (ETDEWEB)

Lortz, Rolf [Department of Condensed Matter Physics, University of Geneva, 24 Quai Ernest-Ansermet, CH-1211 Geneva 4 (Switzerland)], E-mail: Rolf.Lortz@physics.unige.ch; Wang Yuxing; Junod, Alain [Department of Condensed Matter Physics, University of Geneva, 24 Quai Ernest-Ansermet, CH-1211 Geneva 4 (Switzerland); Toyota, Naoki [Physics Department, Graduate School of Science, Tohoku University, 980-8571 Sendai (Japan)

2007-09-01

The range of thermal fluctuations in 'classical' bulk superconductors is extremely small and especially in low-fields hardly experimentally accessible. With a new type of calorimeter we were able to detect a tiny lambda anomaly in the specific-heat of the superconductor Nb{sub 3}Sn within a narrow temperature range around the H{sub c2} line. We show that the evolution of the anomaly as a function of magnetic field follows scaling laws expected in the presence of critical thermal fluctuations.

Superconductors

CERN Document Server

Narlikar, A V

2014-01-01

Superconductors is neither about basic aspects of superconductivity nor about its applications, but its mainstay is superconducting materials. Unusual and unconventional features of a large variety of novel superconductors are presented and their technological potential as practical superconductors assessed. The book begins with an introduction to basic aspects of superconductivity. The presentation is readily accessible to readers from a diverse range of scientific and technical disciplines, such as metallurgy, materials science, materials engineering, electronic and device engineering, and chemistry. The derivation of mathematical formulas and equations has been kept to a minimum and, wherever necessary, short appendices with essential mathematics have been added at the end of the text. The book is not meant to serve as an encyclopaedia, describing each and every superconductor that exists, but focuses on important milestones in their exciting development.

Condensation energy density in Bi-2212 superconductors

International Nuclear Information System (INIS)

Matsushita, Teruo; Kiuchi, Masaru; Haraguchi, Teruhisa; Imada, Takeki; Okamura, Kazunori; Okayasu, Satoru; Uchida, Satoshi; Shimoyama, Jun-ichi; Kishio, Kohji

2006-01-01

The relationship between the condensation energy density and the anisotropy parameter, γ a , has been derived for Bi-2212 superconductors in various anisotropic states by analysing the critical current density due to columnar defects introduced by heavy ion irradiation. The critical current density depended on the size of the defects, determined by the kind and irradiation energy of the ions. A significantly large critical current density of 17.0 MA cm -2 was obtained at 5 K and 0.1 T even for the defect density of a matching field of 1 T in a specimen irradiated with iodine ions. The dependence of the critical current density on the size of the defects agreed well with the prediction from the summation theory of pinning forces, and the condensation energy density could be obtained consistently from specimens irradiated with different ions. The condensation energy density obtained increased with decreasing γ a over the entire range of measurement temperature, and reached about 60% of the value for the most three-dimensional Y-123 observed by Civale et al at 5 K. This gives the reason for the very strong pinning in Bi-2212 superconductors at low temperatures. The thermodynamic critical field obtained decreased linearly with increasing temperature and extrapolated to zero at a certain characteristic temperature, T * , lower than the critical temperature, T c . T * , which seems to be associated with the superconductivity in the block layers, was highest for the optimally doped specimen. This shows that the superconductivity becomes more inhomogeneous as the doped state of a superconductor deviates from the optimum condition

Fluctuation diamagnetism near surfaces and twinning planes in superconductors

International Nuclear Information System (INIS)

Burmistrov, S.N.; Dubovskii, L.B.

1984-01-01

Fluctuations of the magnetic moment and of the specific heat near surfaces and twinning planes in superconductors are studied. Fluctuations near a surface yield an additional contribution to the effect of the usual bulk fluctuations on the diamagnetic moment. Such an additional contribution has a singularity near a temperature T/sub c/3(H), which is higher than the bulk superconducting transition temperature in a magnetic field T/sub c/2(H). Depending on the strength of the magnetic field, the singularity of the additional contribution to the magnetic moment can be either logarithmic (strong fields) or of square-root type (weak fields). Experiments which could reveal the aforementioned anomalous behavior are discussed in detail

On the relevance of the ac magnetic susceptibility on the study of superconductors

International Nuclear Information System (INIS)

Khoder, A.F.; Couach, M.; Barbara, B.

1988-01-01

It is shown that the ac susceptibility method allows to study in details the bulk superconductivity of as well homogeneous and inhomogeneous materials, such as high-T c superconductors. Shielding and Meissner effects at T c can be distinguished by a careful analysis of x' and x'' components of the susceptibility

Superconductor-ferromagnet-superconductor nanojunctions from perovskite materials

International Nuclear Information System (INIS)

Štrbík, V.; Beňačka, Š.; Gaži, Š.; Španková, M.; Šmatko, V.; Knoška, J.; Gál, N.; Chromik, Š.; Sojková, M.; Pisarčík, M.

2017-01-01

Highlights: • Superconductor-ferromagnet-superconductor nanojunction. • Nanojunctions prepared by Ga"3"+ focused ion beam patterning. • Indication of triplet Cooper pair component in junction superconducting current. • Qualitative agreement with theoretical model. - Abstract: The lateral superconductor-ferromagnet–superconductor (SFS) nanojunctions based on high critical temperature superconductor YBa_2Cu_3O_x (YBCO) and half-metallic ferromagnet La_0_._6_7Sr_0_._3_3MnO_3 (LSMO) thin films were prepared to investigate a possible presence of long range triplet component (LRTC) of Cooper pairs in the LSMO. We applied Ga"3"+ focused ion beam patterning to create YBCO/LSMO/YBCO lateral type nanojunctions with LSMO length as small as 40 nm. The resistivity vs. temperature, critical current density vs. temperature and resistance vs. magnetic field dependence were studied to recognize the LRTC of Cooper pairs in the LSMO. A non-monotonic temperature dependence of junction critical current density and a decrease of the SFS nanojunction resistance in increased magnetic field were observed. Only weak manifestations of LRTC and some qualitative agreement with theory were found out in SFS nanojunctions realized from the perovskite materials. The presence of equal-spin triplet component of Cooper pairs in half-metallic LSMO ferromagnet is not such apparent as in SFS junctions prepared from low temperature superconductors NbTiN and half-metallic ferromagnet CrO_2.

FLUX PINNING EFFECTS IN Ag-DOPED YBCO (123 SUPERCONDUCTOR

Directory of Open Access Journals (Sweden)

Madelen Pérez

2010-07-01

Full Text Available Polycrystalline samples of Ag+-doped YBCO (123 (YBa2 (Cu1-xAgx3O7-δwith 0≤x≤0.3 were produced by solid state reaction method. The Ag- doped YBCO samples showed higher critical current densities (Jc with a Jc maximum for samples doped with x=0.05. This behavior can be assigned to an increase of pinning forces. The irreversibility temperature (Tirr, also increased in doped samples as a function of Ag content, with the highest temperature for the sample doped with x=0.05, wich correlates well with the observed Jc increasing. However, samples doped with x>0.05 displayed a decreasing of electrical properties (less Tirr, less Jc, etc. atributed to an excess of Ag in the grain boundaries which, reduces the grain sizes and increases the number of weak- links.

Oxygenation and cracking in melt-textured YBCO bulk superconductors

International Nuclear Information System (INIS)

Kracunovska, S; Diko, P; Litzkendorf, D; Habisreuther, T; Bierlich, J; Gawalek, W

2005-01-01

Microstructural changes during the oxygenation of YBCO bulks were studied. It was shown that a lower temperature of oxygenation leads to the formation of a denser structure of a/b- and c-macrocracks and causes faster and more homogeneous oxygenation of the sample. The opening of created macrocracks is the way in which the macroscopic stresses induced by macroscopic 211 particle concentration inhomogeneity are released. This is very important, because it prevents the formation of fatal c-macrocracks, which divide the sample into more domains, during cooling from oxygenation temperature or during sample performance. Oxygenation with a multistage programme causes the oxygen concentration difference between the oxygenated layer and the tetragonal matrix to be smaller, and consequently fewer macrocracks are formed. This leads to the prolongation of oxygenation times for full oxygenation and to the insufficient release of macroscopic stresses. 211 low concentration regions and pores also enhance the oxygenation rate of YBCO bulks

Deposition of GdVO4:Eu3+ nanoparticles on silica nanospheres by a simple sol gel method

Science.gov (United States)

Liu, Guixia; Hong, Guangyan; Wang, Jinxian; Dong, Xiangting

2006-07-01

The deposition and coating of GdVO4:Eu3+ nanoparticles on spherical silica was carried out using a simple sol-gel method at low temperature. The GdVO4:Eu3+-coated silica composites obtained were characterized by differential thermal analysis (DTA), thermogravimetric (TG) analysis, x-ray diffraction (XRD), Fourier-transform IR spectroscopy (FT-IR), transmission electron microscopy (TEM), x-ray photoelectron spectroscopy (XPS), photoluminescence spectra, and kinetic decay. It is found that the ~5 nm GdVO4:Eu3+ nanoparticles coating the silica spheres are crystal in the as-prepared samples and the crystallinity increases with increasing annealing temperature. The composites obtained are spherical in shape with an average size of 100 nm. The GdVO4:Eu3+ nanoparticles are linked with silica cores by a chemical bond. The photoluminescence spectra of the obtained GdVO4:Eu3+-coated silica composites are similar to those of the bulk GdVO4:Eu3+ phosphors. The strongest peak is near 617 nm, which indicates that Eu3+ is located in the low symmetry site with non-inversion centre.

Effect of mixing RE elements (Nd, Sm, Gd, Eu, Y, Yb) on the RE2BaCuO5/Nd4-2xBa2+2xCu2-xO10-2x phases in RE cuprate high-Tc superconductors

International Nuclear Information System (INIS)

Langhorn, J.B.; Black, M.A.; McGinn, P.J.

1999-01-01

The phases RE 2 BaCuO 5 /RE 4 Ba 2 Cu 2 O 10 phases (where RE is a mixture of Nd, Sm, Gd, Eu, Y and Yb) have been synthesized in an oxygen atmosphere and subsequently characterized. The mixing of RE elements which inherently form the RE 2 BaCuO 5 phase through the peritectic decomposition of REBa 2 Cu 3 O 7-x (RE123) (i.e. Sm, Gd, Eu, Y, Yb), was observed to give homogeneous mixing of the elements in the 211 phase. In contrast it was found that on mixing Nd with other RE elements a mixture of the Nd 4-2x Ba 2+2x Cu 2-x O 10-2x (Nd422) and RE 2 BaCuO 5 (RE211) phases resulted. It was also observed that on mixing Nd with other REs a finite amount of the RE is substituted into the Nd422 phase and Nd into the RE211. (author)

Phase Equilibria Relationships of High-Tc Superconductors

International Nuclear Information System (INIS)

Wong-Ng, Winnie

2011-01-01

As an integral part of a R and D program partially supported by the Electricity Delivery and Energy Reliability Office of DOE, we have determined phase equilibria data and phase diagrams for the three generations of superconductor materials: 1st generation, (Bi,Pb)-Sr-Ca- Cu-O systems; 2nd generation, Ba-R-Cu-O systems (R=lanthanides and yttrium); and 3rd generation, MgB2 systems. Our studies involved bulk materials, single crystals and thin films. This report gives a summary of our accomplishments, a list of publications, and 15 selected journal publications.

Plastic superconductor bearings any size-any shape: 77 K and up

Science.gov (United States)

Reick, Franklin G.

1991-01-01

'Friction free' bearings at 77 K or higher are possible using the high T(sub c) copper oxide ceramic superconductors. The conventional method for making such bearings is to use a sintered ceramic monolith. This puts great restraints on size, shape, and postforming machining. The material is hard and abrasive. It is possible to grind up ceramic superconductors and suspend the granules in a suitable matrix. Mechanical properties improve and are largely dependent on the binder. The Meissner effect is confined to individual grains containing electron vortices. Tracks, rails, levitation areas, and bearings can be made this way with conventional plastic molding and extruding machines or by painting. The parts are easily machined. The sacrifice is in bulk electrical conductivity. A percolating wick feed for LN2 is used to cool remote superconductors and large areas quite effectively. A hollow spheroid or cylinder of superconductor material is molded with the internal surfaces shielded by the Meissner effect. It can be thought of as the DC magnetic analog of the Faraday cage and the inside is the 'Meissner space'. It is selective. The AC fields are transmitted with minor attenuation. Particle size and distribution have a profound effect on final magnetic and electrical characteristics.

Plastic superconductor bearings any size-any shape: 77 K and up

International Nuclear Information System (INIS)

Reick, F.G.

1991-01-01

'Friction free' bearings at 77 K or higher are possible using the high T(sub c) copper oxide ceramic superconductors. The conventional method for making such bearings is to use a sintered ceramic monolith. This puts great restraints on size, shape, and postforming machining. The material is hard and abrasive. It is possible to grind up ceramic superconductors and suspend the granules in a suitable matrix. Mechanical properties improve and are largely dependent on the binder. The Meissner effect is confined to individual grains containing electron vortices. Tracks, rails, levitation areas, and bearings can be made this way with conventional plastic molding and extruding machines or by painting. The parts are easily machined. The sacrifice is in bulk electrical conductivity. A percolating wick feed for LN2 is used to cool remote superconductors and large areas quite effectively. A hollow spheroid or cylinder of superconductor material is molded with the internal surfaces shielded by the Meissner effect. It can be thought of as the DC magnetic analog of the Faraday cage and the inside is the 'Meissner space'. It is selective. The AC fields are transmitted with minor attenuation. Particle size and distribution have a profound effect on final magnetic and electrical characteristics

Low-energy excitations and Fermi surface topology of parent cobaltate superconductor

International Nuclear Information System (INIS)

Hasan, M.Z.; Qian, D.; Foo, M.; Cava, R.J.

2007-01-01

The essential framework for cuprate superconductivity is that of a spin-1/2 electron system in the vicinity of a half filled (Mott limit) lattice. Of all oxide superconductors, this framework is most closely matched in the sodium doped cobalt oxides except that it is realized on a triangular lattice. We employ angle-resolved photoemission spectroscopy to study the quasiparticle dynamics of the parent cobaltate superconductor. Results reveal a single hole-like Fermi surface generated by the crossing of heavy (∼15 m e ∼ 3m LDA ) quasiparticles with a negative effective hopping (t eff F (k → )∼v F ∼0.4±0.1 eV A) observed. ARPES data is consistent with bulk thermodynamic specific heat and quantum oscillation measurements

Research on active magnetic levitation of multiple high-T{sub c} superconductors; Fukusu no baruku chodendotai wo mochiita akuteibu jikifujo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishi, K.; Tachi, K.; Sawa, K. [Keio University, Tokyo (Japan); Iwasa, K. [Francis Bitter Magnet Laboratory, Cambridge (United States); Nagashima, K.; Fujimoto, H. [Railway Technical Research Institute, Tokyo (Japan); Miyamoto, T.; Tomita, M.; Murakami, M. [Superconducting Research Laboratory, Tokyo (Japan)

1999-11-25

This paper describes a new [electromaglev] system, in which multiple Y-Ba-Cu-O bulk superconductors are levitated on a DC magnet. In this system, we have succeeded in controlling the levitation height and force like the case of a single bulk system. We also simulated the total levitation force for multiple bulks, which were in good agreement with the experimental results. (author)

Bulk superconducting gap of V_3Si studied by low-energy ultrahigh-resolution photoemission spectroscopy

International Nuclear Information System (INIS)

Sato, T.; Souma, S.; Nakayama, K.; Sugawara, K.; Toyota, N.; Takahashi, T.

2016-01-01

Highlights: • We report ultrahigh-resolution photoemission spectroscopy of A15 compound V_3Si. • We found a sharp quasiparticle peak due to superconducting-gap opening. • The surface metallic component is negligibly small in the bulk-sensitive measurement. • We show that V_3Si is a single-gap s-wave superconductor. - Abstract: We have performed low-energy ultrahigh-resolution photoemission spectroscopy (PES) of A15 compound V_3Si with a xenon-plasma discharge lamp to elucidate the bulk superconducting gap. Below the superconducting transition temperature (T_c = 15.9 K), we found a sharp quasiparticle peak at the Fermi level in the PES spectrum. The gap spectrum is well fitted by a single s-wave superconducting-gap function together with a dip structure at ∼30 meV suggestive of a strong electron-phonon coupling. The anomalous in-gap state previously observed in the PES measurement with high-energy photons is absent or negligibly small in the present bulk-sensitive measurement. The present PES result shows that V_3Si is a single-gap s-wave superconductor.

Superconductor-ferromagnet-superconductor nanojunctions from perovskite materials

Energy Technology Data Exchange (ETDEWEB)

Štrbík, V., E-mail: vladimir.strbik@savba.sk [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia); Beňačka, Š.; Gaži, Š.; Španková, M.; Šmatko, V. [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia); Knoška, J. [Center for Free-Electron Laser Science, DESY, Notkestraße 85, 22607, Hamburg (Germany); Department of Physics, University of Hamburg, Luruper Chaussee 149, 22607, Hamburg (Germany); Gál, N.; Chromik, Š.; Sojková, M.; Pisarčík, M. [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia)

2017-02-15

Highlights: • Superconductor-ferromagnet-superconductor nanojunction. • Nanojunctions prepared by Ga{sup 3+} focused ion beam patterning. • Indication of triplet Cooper pair component in junction superconducting current. • Qualitative agreement with theoretical model. - Abstract: The lateral superconductor-ferromagnet–superconductor (SFS) nanojunctions based on high critical temperature superconductor YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) and half-metallic ferromagnet La{sub 0.67}Sr{sub 0.33}MnO{sub 3} (LSMO) thin films were prepared to investigate a possible presence of long range triplet component (LRTC) of Cooper pairs in the LSMO. We applied Ga{sup 3+} focused ion beam patterning to create YBCO/LSMO/YBCO lateral type nanojunctions with LSMO length as small as 40 nm. The resistivity vs. temperature, critical current density vs. temperature and resistance vs. magnetic field dependence were studied to recognize the LRTC of Cooper pairs in the LSMO. A non-monotonic temperature dependence of junction critical current density and a decrease of the SFS nanojunction resistance in increased magnetic field were observed. Only weak manifestations of LRTC and some qualitative agreement with theory were found out in SFS nanojunctions realized from the perovskite materials. The presence of equal-spin triplet component of Cooper pairs in half-metallic LSMO ferromagnet is not such apparent as in SFS junctions prepared from low temperature superconductors NbTiN and half-metallic ferromagnet CrO{sub 2}.

Microwave surface resistance of bulk YBa2Cu3O6+x material

Science.gov (United States)

Fathy, A.; Kalokitis, D.; Belohoubek, E.; Sundar, H. G. K.; Safari, A.

1988-10-01

Superconducting Y-Ba-Cu-O samples were prepared by conventional solid-state reaction. The microwave surface resistance of 1:2:3 compound superconductor material was measured in a special disk resonator structure at 10 GHz. At liquid-nitrogen temperatures the microwave surface resistance is comparable to that of Au. At lower temperature (~10 K) the surface resistance is an order of magnitude lower than that of Au at the same temperature.

Trapped magnetic field measurements on HTS bulk by peak controlled pulsed field magnetization

International Nuclear Information System (INIS)

Ida, Tetsuya; Watasaki, Masahiro; Kimura, Yosuke; Miki, Motohiro; Izumi, Mitsuru

2010-01-01

For the past several years, we have studied the high-temperature superconducting (HTS) synchronous motor assembled with melt-textured Gd-Ba-Cu-O bulk magnets. If the single pulse field magnetizes a bulk effectively, size of electrical motor will become small for the strong magnetic field of the HTS magnets without reducing output power of motor. In the previous study, we showed that the HTS bulk was magnetized to excellent cone-shape magnetic field distribution by using the waveform control pulse magnetization (WCPM) method. The WCPM technique made possible the active control of the waveform on which magnetic flux motion depended. We generated the pulse waveform with controlled risetime for HTS bulk magnetization to suppress the magnetic flux motion which decreases magnetization efficiency. The pulsed maximum magnetic flux density with slow risetime is not beyond the maximum magnetic flux density which is trapped by the static field magnetization. But, as for applying the pulse which has fast risetime, the magnetic flux which exceed greatly the threshold penetrates the bulk and causes the disorder of the trapped magnetic distribution. This fact suggests the possibility that the threshold at pulsed magnetization influences the dynamic magnetic flux motion. In this study, Gd-Ba-Cu-O bulk is magnetized by the controlled arbitrary trapezoidal shape pulse, of which the maximum magnetic flux density is controlled not to exceed the threshold. We will present the trapped magnetic characteristics and the technique to generate the controlled pulsed field.

Development of all chemical solution derived Ce_0.9La_0.1O_{2 − y}/Gd₂Zr₂O₇ buffer layer stack for coated conductors: influence of the post-annealing process on surface crystallinity

DEFF Research Database (Denmark)

Yue, Zhao; Li, Xiaofen; Khoryushin, Alexey

2012-01-01

Preparation and characterization of a biaxially textured Gd2Zr2O7 and Ce0.9La0.1O2 − y (CLO, cap)/Gd2Zr2O7 (GZO, barrier) buffer layer stack by the metal–organic deposition route are reported. YBa2Cu3O7 − d (YBCO) superconductor films were deposited by the pulsed-laser deposition (PLD) technique ...

Investigation of pinning in MgB2 superconductors

International Nuclear Information System (INIS)

Mohammad, S.; Reissner, M.; Steiner, W.; Bauer, E.; Giovannini, M.

2006-01-01

Full text: The pinning behaviour of bulk MgB 2 superconductors is peculiar in many respects. Pinning seems to be stronger than in classical high T C materials and there seems to be no weak link problem in these compounds, giving hope to produce bulk samples and wires with current densities appropriate for technical applications. But, although many studies concerning the pinning behaviour in this compound appeared in recent years, the results are still contradictory. In the present work we present results of an investigation of the pinning behaviour by magnetic relaxation measurements of three MgB 2 samples: a pure one, a sample with 8 at% Al substitution and a sample with 10 wt% of SiC admixture. A comparison of different analyses methods is given. (author)

Influences of cooling height and lateral moving speed on the levitation characteristics of YBaCuO bulks

International Nuclear Information System (INIS)

Zhou Jun; Zhang Xingyi; Zhou Youhe

2009-01-01

Using an updated high-temperature superconductor (HTS) maglev measurement system, electromagnetic forces between a YBaCuO bulk superconductor and a permanent magnet (PM) have been measured under different cooling height (CH) and different lateral moving speed of the PM. It is found that the influence of the moving speed on both the levitation and lateral force is substantial and as such the results shown in this work are a benefit to the understanding of levitation systems.

Influences of cooling height and lateral moving speed on the levitation characteristics of YBaCuO bulks

Energy Technology Data Exchange (ETDEWEB)

Zhou Jun; Zhang Xingyi [Key Laboratory of Mechanics on Western Disaster and Environment, Department of Mechanics and Engineering Science, College of Civil Engineering and Mechanics, Lanzhou University, Lanzhou, Gansu 730000 (China); Zhou Youhe, E-mail: Zhouyh@lzu.edu.c [Key Laboratory of Mechanics on Western Disaster and Environment, Department of Mechanics and Engineering Science, College of Civil Engineering and Mechanics, Lanzhou University, Lanzhou, Gansu 730000 (China)

2009-03-15

Using an updated high-temperature superconductor (HTS) maglev measurement system, electromagnetic forces between a YBaCuO bulk superconductor and a permanent magnet (PM) have been measured under different cooling height (CH) and different lateral moving speed of the PM. It is found that the influence of the moving speed on both the levitation and lateral force is substantial and as such the results shown in this work are a benefit to the understanding of levitation systems.

Improvement of critical currents in Bi-2223 bulk superconductors

International Nuclear Information System (INIS)

Eujen, R.; Brauer, D.J.; Huedepohl, J.

1991-01-01

Potential applications of the high-Tc superconductors for energy transport or high-field magnets require high critical current densities. A limiting factor in polycrystalline oxidic materials is the quality of the grain boundaries. Weak links have been made responsible for the steep decrease in the critical current density j c upon application of even weak magnetic fields of YBa CuO whereas flux creep seems to dominate the obtainable j c values for the Bi-Sr-Ca-Cu-O system (BSCCO) at 77 K. In the lead containing material (BPSCCO) the formation of a porous microstructure is enhanced by the platelike shape of the crystals. Special techniques such as powder-in-tube, hot isostatic pressing, zone melting or application of fluxes have been used in order to improve the grain contacts. A positive influence of fluxes on j c , e.g. by addition of Ca 2 CuO 3 or Ag 2 O, has been reported. In this study we have investigated the influence of various compositions and conditions on the formation of the BSCCO-2223 phase (T c ca. 107 K), the critical current density j c , and the magnet field dependence of the a.c. susceptibility. (orig.)

Quasiparticle lifetimes and tunneling times in a superconductor-insulator-superconductor tunnel junction with spatially inhomogeneous electrodes

International Nuclear Information System (INIS)

Golubov, A.A.; Houwman, E.P.; Gijsbertsen, J.G.; Flokstra, J.; Rogalla, H.; le Grand, J.B.; de Korte, P.A.J.

1994-01-01

The low-energy quasiparticle scattering and recombination lifetimes for a proximity sandwich of two superconductors S and S' with different bulk energy gaps, are calculated as a function of the spatial coordinate and temperature. The spatial dependence of the order parameter and density of states are calculated on the basis of a microscopic model of the proximity effect, based on the Usadel equations, for dirty superconductors in thermal equilibrium. A zero boundary resistance between S and S' and a Boltzmann-like energy distribution of the excess quasiparticles are assumed. In the case of a small diffusion time constant an effective quasiparticle relaxation rate into and excitation rate out of the reduced gap region in the SS' sandwich are obtained as a function of (finite, but low) temperature and strength of the proximity effect, determined by the parameter γ m , by averaging over the energies and positions of the quasiparticles. In the same way effective tunneling times for electrons and holes tunneling out of the trap in the SS' sandwich to the other electrode of an SS'IS''S junction are determined as a function of temperature, voltage, and γ m

A review of finite size effects in quasi-zero dimensional superconductors

International Nuclear Information System (INIS)

Bose, Sangita; Ayyub, Pushan

2014-01-01

Quantum confinement and surface effects (SEs) dramatically modify most solid state phenomena as one approaches the nanometer scale, and superconductivity is no exception. Though we may expect significant modifications from bulk superconducting properties when the system dimensions become smaller than the characteristic length scales for bulk superconductors—such as the coherence length or the penetration depth—it is now established that there is a third length scale which ultimately determines the critical size at which Cooper pairing is destroyed. In quasi-zero-dimensional (0D) superconductors (e.g. nanocrystalline materials, isolated or embedded nanoparticles), one may define a critical particle diameter below which the mean energy level spacing arising from quantum confinement becomes equal to the bulk superconducting energy gap. The so-called Anderson criterion provides a remarkably accurate estimate of the limiting size for the destabilization of superconductivity in nanosystems. This review of size effects in quasi-0D superconductors is organized as follows. A general summary of size effects in nanostructured superconductors (section 1) is followed by a brief overview of their synthesis (section 2) and characterization using a variety of techniques (section 3). Section 4 reviews the size-evolution of important superconducting parameters—the transition temperature, critical fields and critical current—as the Anderson limit is approached from above. We then discuss the effect of thermodynamic fluctuations (section 5), which become significant in confined systems. Improvements in fabrication methods and the increasing feasibility of addressing individual nanoparticles using scanning probe techniques have lately opened up new directions in the study of nanoscale superconductivity. Section 6 reviews both experimental and theoretical aspects of the recently discovered phenomena of ‘parity effect’ and ‘shell effect’ that lead to a strong, non

Levitation force and magnetization in bulk and thin film high T{sub c} superconductors

Energy Technology Data Exchange (ETDEWEB)

Riise, A.B

1998-04-01

The authors present high-resolution measurements of the repulsive vertical force and its associated stiffness between a Nd-B-Fe magnet and a YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} superconductor in cylindrical geometry. The results are compared with theoretical predictions. The calculations are based on a model in which the superconductor is assumed to be either a sintered granular material or consisting of grains embedded in a nonactive matrix so that only intragranular currents are important. The critical state model is applied to each grain individually and closed form expressions for both vertical force F{sub z} and stiffness are obtained in a configuration with cylindrical symmetry. The model explains all features of the experimental results in a consistent way. A good quantitative agreement has been obtained using only three adjustable parameters. Several central aspects of the phenomenon of magnetic levitation with high-T{sub c} superconductors are presented. High-resolution measurements are made of the repulsive vertical force and its associated stiffness as well as the horizontal stabilizing force and the stiffness governing lateral vibrations. The results obtained at 77 K using a granular YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} sample and Nd-Fe-B magnet in a rectangular levitation configuration are compared with theoretical predictions. The calculations, which are based on the critical state model with the assumption that it applies to the grins individually, give closed-form expressions for all the measured quantities. It is concluded that the present model explains all features of the observations in a consistent way. Using only three adjustable parameters a good agreement exists also at a quantitative level. Experimental studies and theoretical modelling of the levitation force on a permanent magnet placed above a superconducting thin film are offered. It is shown that measurements of the levitation force is a simple and precise method to determine the

Superconducting Cd and Ca doped 123 phase in Cdo.8Ba2(Y0.7Ca0.4) Cu3.5Oy

International Nuclear Information System (INIS)

Balchev, N.; Kovachev, V; THOMAS, J.; BIEGER, W.; Konstantinov, K.; Kunev, B.

1999-01-01

A new Cd-containing superconductor with nominal composition of Cd 0.8 Ba 2 (Y 0.7 Ca 0.4 ) Cu 3.5 O y and T c = 80 K was synthesized and investigated. The obtained XRD pattern shows that the dominating phase is an orthorhombic 123. It was shown that the presence of Cd and Ca facilitates the 123 phase formation. The results of the EDX analysis on SEM and TEM have shown that the distribution of the Cd and Ca in the samples is inhomogeneous. The two elements enter the 123 phase in most of the investigated crystals and form a new Cd-Ba-Y-Ca-Cu-O superconducting compound

Temperature effects on separation of Gd3+ from Gd-DTPA-folate using nanofiltration method

Science.gov (United States)

Rahayu, I.; Indraneli, R. P.; Yuliyati, Y. B.; Anggraeni, A.; Soedjanaatmadja, U. M. S.; Bahti, H. H.

2018-05-01

MRI is one of the best techniques in medical diagnostics. Contrast agents are used to improve the visual of organs that are difficult to distinguish through MRI. Gd-DTPA-folate is one of the specific contrast agents against cancer diagnosis, because it has a high affinity to folate receptors. In the complexing Gd-DTPA-folate, does not rule out the complexity step runs imperfectly, so there is still Gd3+ in the Gd-DTPA-folate complex. The separation of Gd3+ from the Gd-DTPA-folate complex is important to eliminate toxic effects on the contrast agent. This study aims to determine the effect of temperature on the separation of Gd-DTPA-folate from Gd3+ with nanofiltration. The method are preparation Gd-DTPA-folate from GdCl3.6H2O and DTPA-folate by reflux method, then separated Gd-DTPA-folate complex from Gd3+ with nanofiltration at variation temperature (40, 41, 42, 43, 44oC ). Then, the values of flux and rejection coefficients were analyzed. The results showed that the optimum temperature for the separation of Gd3+ from Gd-DTPA-folate was achieved at 42.6°C with the rejection coefficient of 24% and the permeate flux of 403 L.m-2.h-1.

Superconductors

International Nuclear Information System (INIS)

1988-01-01

The chapter 6.3 p. 143 to 153 of this book deals with superconductors 19 items are briefly presented with address of manufacturer or laboratory to contact, mainly in the USA or Japan. In particular magnets, films, high temperature superconductors and various applications are presented [fr

Time domain simulation of Gd3+-Gd3+ distance measurements by EPR

Science.gov (United States)

Manukovsky, Nurit; Feintuch, Akiva; Kuprov, Ilya; Goldfarb, Daniella

2017-07-01

Gd3+-based spin labels are useful as an alternative to nitroxides for intramolecular distance measurements at high fields in biological systems. However, double electron-electron resonance (DEER) measurements using model Gd3+ complexes featured a low modulation depth and an unexpected broadening of the distance distribution for short Gd3+-Gd3+ distances, when analysed using the software designed for S = 1/2 pairs. It appears that these effects result from the different spectroscopic characteristics of Gd3+—the high spin, the zero field splitting (ZFS), and the flip-flop terms in the dipolar Hamiltonian that are often ignored for spin-1/2 systems. An understanding of the factors affecting the modulation frequency and amplitude is essential for the correct analysis of Gd3+-Gd3+ DEER data and for the educated choice of experimental settings, such as Gd3+ spin label type and the pulse parameters. This work uses time-domain simulations of Gd3+-Gd3+ DEER by explicit density matrix propagation to elucidate the factors shaping Gd3+ DEER traces. The simulations show that mixing between the |+½, -½> and |-½, +½> states of the two spins, caused by the flip-flop term in the dipolar Hamiltonian, leads to dampening of the dipolar modulation. This effect may be mitigated by a large ZFS or by pulse frequency settings allowing for a decreased contribution of the central transition and the one adjacent to it. The simulations reproduce both the experimental line shapes of the Fourier-transforms of the DEER time domain traces and the trends in the behaviour of the modulation depth, thus enabling a more systematic design and analysis of Gd3+ DEER experiments.

A low-cost batch process for high-performance melt-textured GdBaCuO pellets

Czech Academy of Sciences Publication Activity Database

Muralidhar, M.; Tomita, M.; Suzuki, K.; Jirsa, Miloš; Fukumoto, .Y.; Ishihara, A.

2010-01-01

Roč. 23, č. 4 (2010), 045033/1-045033/7 ISSN 0953-2048 Institutional research plan: CEZ:AV0Z10100520 Keywords : superconducting magnet * GdBaCuO * batch process * high-Tc bulk Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.402, year: 2010

Studies on ceramic superconductors

International Nuclear Information System (INIS)

Chaklader, A.C.D.; Roemer, G.; Hardy, W.N.; Brewer, J.H.; Carolan, J.F.; Parsons, R.R.

1987-01-01

The superconducting properties of both bulk specimens and sputtered thin films of the YBa 2 Cu 3 O x compound have been studied. The bulk specimens were fabricated by cold pressing and sintering, and also by hot-pressing (subsequent reheating). The dc resistivity measurements showed a sharp drop in the temperature range 92-87K in this material. Muon spin relaxation (μSR) measurements of sintered discs in 3.4 kOe revealed the formation of a mixed state with an effective magnetic penetration depth λ ∼ 1365 angstrom at 6K, implying an effective charge carrier density of 6 x 10 21 cm -3 . The temperature dependence λ(T) is that of an ordinary s-wave superconductor. The resistivity of the thin film prepared from the compound by dc planar magnetron sputtering, showed a sharp drop to a very low value near 80K. The compound YBa 2 Cu 3 O x loses its superconducting properties, when either hot-pressed (in air) or oxidized at 500 degree C in high O 2 pressure, but this property can be restored when reheated in one atmosphere of O 2 above 900 degree C

Hall effect and magnetization in the magnetic superconductor RuSr2GdCu2O8

International Nuclear Information System (INIS)

Jurelo, A.R.; Pimentel, J.L.; Wolff Fabris, F.; Schaf, J.; Pureur, P.; Vieira, V.N.

2006-01-01

We report on Hall effect, longitudinal resistivity and magnetization measurements in the rutheno-cuprate RuSr 2 GdCu 2 O 8 . Combining these results we separate the anomalous contribution to the Hall effect and argue that the occurrence of canting and chirality have to be considered for describing this property

Raman characterization of bulk ferromagnetic nanostructured graphite

International Nuclear Information System (INIS)

Pardo, Helena; Divine Khan, Ngwashi; Faccio, Ricardo; Araújo-Moreira, F.M.; Fernández-Werner, Luciana

2012-01-01

Raman spectroscopy was used to characterize bulk ferromagnetic graphite samples prepared by controlled oxidation of commercial pristine graphite powder. The G:D band intensity ratio, the shape and position of the 2D band and the presence of a band around 2950 cm -1 showed a high degree of disorder in the modified graphite sample, with a significant presence of exposed edges of graphitic planes as well as a high degree of attached hydrogen atoms.

Organic superconductors

International Nuclear Information System (INIS)

Bulaevskij, L.N.; Shchegolev, I.F.

1986-01-01

Main achievements in creating new organic conducting materials - synthetic metals and superconductors, are considered. The processes of superconductivity occurrence in organic materials are discussed. It is shown that conjugated bonds between C and H atoms in organic molecules play an important role in this case. At present ''crystal direction'' in organic superconductor synthesis is mainly developed. Later on, organic superconductor crystals are supposed to be introduced into usual polymers, e.g. polyethylene

Photoluminescence related to Gd3+:N-vacancy complex in GaN:Gd multi-quantum wells

International Nuclear Information System (INIS)

Almokhtar, Mohamed; Emura, Shuichi; Koide, Akihiro; Fujikawa, Takashi; Asahi, Hajime

2015-01-01

Highlights: • We grew Gd-doped GaN multi-quantum wells (MQWs) with quantum layer thickness of one nm by MBE. • The X-ray absorption near edge structure spectra observed at Gd LIII-edge indicate a nitrogen vacancy adjacent to Gd substituting the Ga ion in Gd-doped GaN MQW. • The photoluminescence of the samples is discussed considering the formation of a Gd 3+ :Nitrogen-vacancy complex. • A model is presented considering exciton-polaron formation trapped in defect sites around the Gd 3+ :N-vacancy complex in Gd-doped GaN MQWs. - Abstract: The photoluminescence of Gd-doped GaN multi-quantum wells (MQWs) is presented and discussed considering the formation of a Gd 3+ :Nitrogen-vacancy (N-vacancy) complex. A lower energy photoluminescence peak was observed for the Gd-doped GaN MQW sample with respect to the main peak assigned to a neutral donor bound exciton (D 0 X) of the undoped GaN MQW sample. The X-ray absorption near edge structure spectrum observed at Gd L III -edge indicates a nitrogen vacancy adjacent to the Gd substituting the Ga ion in Gd-doped GaN MQW sample. Local stresses around the Gd dopants in Gd-doped GaN matrix generated due to the larger diameter of the Gd 3+ ion with respect to the Ga 3+ ion can be relieved by the creation of vacancies. The lower formation energy of N-vacancies in GaN matrix introduce them as a preferred candidate to relieve the generated stresses. A Gd 3+ :N-vacancy complex consisting of a Gd 3+ ion and the created nitrogen vacancy adjacent to the Gd 3+ dopant is likely to form in GaN:Gd matrix. The lower photoluminescence peak energy observed in the Gd-doped GaN MQW sample is assigned to the recombination of an exciton captured at the Gd 3+ :N-vacancy complex forming a small polaron-like state. A model is presented considering the small exciton-polaron population in defect sites captured around the Gd 3+ ions in the Gd-doped GaN

NMR measurements in milled GdCo2 and GdFe2 intermetallic compounds

International Nuclear Information System (INIS)

Tribuzy, C.V.B.; Guimaraes, A.P.; Biondo, A.; Larica, C.; Alves, K.M.B.

1998-12-01

We have used the nuclear magnetic resonance technique to study the magnetic and structural properties of the Gd-Co and Gd-Fe metallic systems, starting with the C15 laves phase intermetallic compounds, and submitting them to a high energy milling process. This leads to the amorphization of the samples, as determined by the X-ray diffraction spectra. For the Gd-Co system the NMR study used the 59 Co nucleus; in the Gd-Fe system, 155,157 Gd and 57 Fe were used. Both systems showed segregation of the pure elements, after a few hours of milling. In the Gd-Co system, a single line, of increasing width, was observed in the 59 Co spectrum. In the Gd-Fe system, the 155 Gd and 157 Gd resonances show three lines, arising from electrical quadrupole interaction. With increasing milling time, the lines broaden, and extra lines appear attributed to a cubic phase of Gd; this interpretation is supported by the X-ray analysis of the samples. The 57 Fe NMR spectrum of this system also informs on the direction of magnetization of the samples in the early stages of milling. From 1 h to 7 h of milling, a spectrum of α-Fe was observed. The study of the NMR line intensity as a function of radio frequency (r.f.) power in Gd Co 2 suggests the existence of regions of the samples with different degrees of disorder. We have observed the persistence of NMR signals from the original intermetallic compounds in the samples with up to 10 h and 7 h of milling, respectively, for Gd Co 2 and Gd Fe 2 . (author)

Flux pinning enhancement by Y2BaCuO5 inclusions in melt processed YBaCuO superconductors

International Nuclear Information System (INIS)

Murakami, M.

1991-01-01

While nonsuperconducting particles are known to serve as effective pinning centers in conventional superconductors, their effect in high T c superconductors is still controversial. In this paper, the author gives evidence that nonsuperconducting Y 2 BaCuO 5 (21 1) inclusions can act as pinning centers in melt processed YBaCuO superconductors even when their size is orders of magnitude larger than the coherence length. In such a case, the interface provides pinning. Theoretical estimates based on direct summations agree well with the experimental results. The applications of direct summation for obtaining the bulk pinning force is justified by direct observation of the FLL (flux line lattice), where the FLL has no long range order and the fluxoids are pinned by 211 inclusions

MR imaging of the cochlear modiolus after intratympanic administration of Gd-DTPA

International Nuclear Information System (INIS)

Kawai, Hisashi; Naganawa, Shinji; Ishihara, Shunichi; Sone, Michihiko; Nakashima, Tsutomu

2010-01-01

We evaluated whether enhancement of the cochlear modiolus could be visualized 24 hours after intratympanic injection of gadolinium diethylenetriamine penta-acetic acid (Gd-DTPA) using a 3-dimensional real inversion recovery sequence combined with a 32-channel head coil at 3 tesla. Intratympanic injection of Gd-DTPA has been reported for visualizing endolymphatic hydrops in Meniere's disease, and its use has shown communication between the cochlear perilymph and cerebrospinal fluid in the internal auditory canal. Although the cochlear modiolus has been considered the route for this communication, this has not been confirmed through direct visualization of its enhancement. We qualitatively and quantitatively evaluated the presence of contrast enhancement in the modiolus in 19 patients with clinically suspected endolymphatic hydrops or hearing loss who underwent imaging as described above. The contrast ratio (CR) between the cochlear modiolus and cerebellar white matter on the injected side was 1.09±1.23, and that on the non-injected side was -0.48±0.38 (P<0.01). In all subjects, the CR value was larger on the injected than non-injected side, and enhancement of the cochlear modiolus was also recognized visually. Intratympanic Gd-DTPA can be administered to visualize enhancement of the cochlear modiolus and may thereby reveal its functional anatomy. (author)

PdTe: a 4.5 K type-II BCS superconductor

International Nuclear Information System (INIS)

Tiwari, Brajesh; Goyal, Reena; Jha, Rajveer; Awana, V P S; Dixit, Ambesh

2015-01-01

We report on the structure and physical properties of the polycrystalline PdTe superconductor, which is synthesized by the solid state reaction route via the quartz vacuum encapsulation technique at 750 °C. The as synthesized compound is crystallized in hexagonal crystal structure with P63/mmc space group. Both transport and magnetic measurements showed that PdTe is a bulk superconductor below 4.5 K. Isothermal magnetization (MH) and magneto-transport (R(T)H) measurements provided the values of the lower (H c1 ) and upper (H c2 ) critical fields as 250 Oe and 1200 Oe respectively at 2 K, establishing that the compound is clearly a type-II superconductor. The coherence length (ξ 0 ) and Ginzburg–Landau parameter (κ) are estimated from the experimentally determined upper and lower critical fields, and are 449 Å and 1.48 respectively. Thermodynamic heat capacity measurements under different magnetic fields, i.e. C p (T)H, showed a clear transition at 4.5 K (T c ), which shifts gradually to lower temperatures with application of field. The values of Debye temperature (Θ D ) and electronic specific heat coefficient (γ) obtained from C p (T) data are found to be 203 K and 6.01 mJ mol −1 K −2 . The observed specific heat jump (ΔC/γT c ) is 1.33, thus suggesting a possible weak coupling case for the PdTe superconductor. (paper)

The Pr and Ca Substitution in GdBa2Cu3O7- & delta

Directory of Open Access Journals (Sweden)

H. S. H.

2001-12-01

Full Text Available   The granular Gd1-x-zPrxCazBa2Cu3O7-δ high-temperature cuprate samples with 0.0 ≤ x ≤ 0.3 and 0.0≤ x ≤ 0.35 are prepared by standard solid state reaction and characterized by XRD and SEM techniques. The BaCuO2 and impurity phases are less than 1% in the samples having high levels of pr and Ca concentrations. The electrical resistivity measurements show a nonlinear reduction in Tc(x,z=etc versus x. Moreover, the Tc(z curve with x=0 is nonlinear and aplateau appears at z≈ 0.05-0.015. For Pr-Ca-doped samples with a constant concentration of Pr, Tc increases with the increase of Ca up to an optimum value of Ca doping and then in decreases. Based on these observations, we suggest that hole filling and hole localization the main effects of Pr ion substiution. The magnetic measurements indicate that the value of Hc1 is in the order of 10 mT. The mangetoresistance measurements have been measured and analyzed. The superconducting transition region is broadened by the application of magnetic field. The experimental data near the onsen of superconductivity are fitted with the Ambegakor and Halperin (AH phase-slip model. We observe that the AH parameter,γ (H, depends not only on the temperature and the magnetic field, but also on the Pr and Ca ions concentrations. It is observed that the critical current density increases with Ca substitution and decreases with Pr substitution in Gd-123 system. We suggest that the Pr ion substitution probably enhances the weak link, but the Ca ion acts as flux pinning center in the GdPrCa-123 system.

Multiorgan gadolinium (Gd) deposition and fibrosis in a patient with nephrogenic systemic fibrosis--an autopsy-based review

DEFF Research Database (Denmark)

Sanyal, Soma; Marckmann, Peter; Scherer, Susanne

2011-01-01

tissues of NSF patients, predominantly at the bulk chemical level. The distribution of Gd at the histologic level of organs other than skin has not been reported previously. METHODS: We analysed tissues from an autopsy case with verified advanced NSF by light microscopy and scanning electron microscopy......), kidney, lymph node, skeletal muscle, dura mater and cerebellum of the NSF autopsy case, primarily in vascular walls. Some, but not all, Gd deposits were seen in fibrotic areas. Literature review highlighted that non-specific tissue fibrosis and calcification are frequent findings in tissues of patients...

The magnetic order of GdMn{sub 2}Ge{sub 2} studied by neutron diffraction and x-ray resonant magnetic scattering

Energy Technology Data Exchange (ETDEWEB)

Granovsky, S A [M V Lomonosov Moscow State University, 119991 GSP-1 Moscow (Russian Federation); Kreyssig, A; Canfield, P C [Ames Laboratory USDOE, Iowa State University, Ames, IA 50011 (United States); Doerr, M; Loewenhaupt, M [TU Dresden, Institut fuer Festkoerperphysik, D-01062, Dresden (Germany); Ritter, C [Institut Laue-Langevin, F-38042 Grenoble Cedex 9 (France); Dudzik, E; Feyerherm, R, E-mail: ser@plms.r [Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, BESSY, D-12489, Berlin (Germany)

2010-06-09

The magnetic structure of GdMn{sub 2}Ge{sub 2} (tetragonal I4/mmm) has been studied by hot neutron powder diffraction and x-ray resonant magnetic scattering techniques. These measurements, along with the results of bulk experiments, confirm the collinear ferrimagnetic structure with moment direction parallel to the c-axis below T{sub C} = 96 K and the collinear antiferromagnetic phase in the temperature region T{sub C} < T < T{sub N} = 365 K. In the antiferromagnetic phase, x-ray resonant magnetic scattering has been detected at Mn K and Gd L{sub 2} absorption edges. The Gd contribution is a result of an induced Gd 5d electron polarization caused by the antiferromagnetic order of Mn-moments.

Effect of axial strain on the critical current of Ag-sheathed Bi-based superconductors in magnetic fields up to 25 T

International Nuclear Information System (INIS)

Ekin, J.W.; Finnemore, D.K.; Li, Q.; Tenbrink, J.; Carter, W.

1992-01-01

The irreversible strain limit ε irrev for the onset of permanent axial strain damage to Ag-sheathed Bi 2 Sr 2 Ca 1 Cu 2 O 8+x and Bi 2 Sr 2 Ca 2 Cu 3 O 10+x superconductors has been measured to be in the range of 0.2%--0.35%. This strain damage onset is about an order of magnitude higher than for bulk sintered Y-, Bi-, or Tl-based superconductors and is approaching practical values for magnet design. The measurements show that the value of ε irrev is not dependent on magnetic field, nor does the critical current depend on strain below ε irrev at least up to 25 T at 4.2 K. Both of these factors indicate that the observed strain effect in Ag-sheathed Bi-based superconductors is not intrinsic to the superconductor material. Rather, the effect is extrinsic and arises from superconductor fracture. Thus, the damage onset is amenable to further enhancement. Indeed, the data suggest that subdividing the superconductor into fine filaments or adding Ag to the superconductor powder prior to processing significantly enhances the damage threshold ε irrev to above 0.6%

Fracture analysis of a central crack in a long cylindrical superconductor with exponential model

Science.gov (United States)

Zhao, Yu Feng; Xu, Chi

2018-05-01

The fracture behavior of a long cylindrical superconductor is investigated by modeling a central crack that is induced by electromagnetic force. Based on the exponential model, the stress intensity factors (SIFs) with the dimensionless parameter p and the length of the crack a/R for the zero-field cooling (ZFC) and field-cooling (FC) processes are numerically simulated using the finite element method (FEM) and assuming a persistent current flow. As the applied field Ba decreases, the dependence of p and a/R on the SIFs in the ZFC process is exactly opposite to that observed in the FC process. Numerical results indicate that the exponential model exhibits different characteristics for the trend of the SIFs from the results obtained using the Bean and Kim models. This implies that the crack length and the trapped field have significant effects on the fracture behavior of bulk superconductors. The obtained results are useful for understanding the critical-state model of high-temperature superconductors in crack problem.

Fabrication of high temperature superconductors

Science.gov (United States)

Balachandran, Uthamalingam; Dorris, Stephen E.; Ma, Beihai; Li, Meiya

2003-06-17

A method of forming a biaxially aligned superconductor on a non-biaxially aligned substrate substantially chemically inert to the biaxially aligned superconductor comprising is disclosed. A non-biaxially aligned substrate chemically inert to the superconductor is provided and a biaxially aligned superconductor material is deposited directly on the non-biaxially aligned substrate. A method forming a plume of superconductor material and contacting the plume and the non-biaxially aligned substrate at an angle greater than 0.degree. and less than 90.degree. to deposit a biaxially aligned superconductor on the non-biaxially aligned substrate is also disclosed. Various superconductors and substrates are illustrated.

Gd_2O_3 nanoparticles stabilized by hydrothermally modified dextrose for positive contrast magnetic resonance imaging

International Nuclear Information System (INIS)

Babić-Stojić, Branka; Jokanović, Vukoman; Milivojević, Dušan; Požek, Miroslav; Jagličić, Zvonko; Makovec, Darko; Arsikin, Katarina; Paunović, Verica

2016-01-01

Gd_2O_3 nanoparticles of a few nm in size and their agglomerates dispersed in dextrose derived polymer template were synthesized by hydrothermal treatment. The produced nanosized material was investigated by TEM, FTIR spectroscopy, SQUID measurements and NMR relaxometry. Biological evaluation of this material was done by crystal violet and MTT assays to determine the cell viability. Longitudinal and transverse NMR relaxivities of water diluted Gd_2O_3 nanoparticle dispersions measured at the magnetic field of 1.5 T, estimated to be r_1(Gd_2O_3)=9.6 s"−"1 mM"−"1 in the Gd concentration range 0.1–30 mM and r_2(Gd_2O_3)=17.7 s"−"1 mM"−"1 in the lower concentration range 0.1–0.8 mM, are significantly higher than the corresponding relaxivities measured for the standard contrast agent r_1(Gd-DTPA)=4.1 s"−"1 mM"−"1 and r_2(Gd-DTPA)=5.1 s"−"1 mM"−"1. The ratio of the two relaxivities for Gd_2O_3 nanoparticles r_2/r_1=1.8 is suitable for T_1-weighted imaging. Good MRI signal intensities of the water diluted Gd_2O_3 nanoparticle dispersions were recorded at lower Gd concentrations 0.2–0.8 mM. The Gd_2O_3 samples did not exert any significant cytotoxic effects at Gd concentrations of 0.2 mM and below. These properties of the produced Gd_2O_3 nanoparticles in hydrothermally modified dextrose make them promising for potential application in MRI for the design of a positive MRI contrast agent. - Highlights: • Gd_2O_3 nanoparticles (NPs) were stabilized by hydrothermally modified dextrose. • Magnetic moment per Gd"3"+ ion in the Gd_2O_3 NPs is much lower than that in the bulk. • The ratio r_2/r_1=1.8 for Gd_2O_3 NPs dispersions is favorable for T_1-weighted MRI. • Gd_2O_3 NPs dispersions had good MRI signal intensity just at lower Gd concentrations. • Gd concentrations of 0.2 mM and below in the Gd_2O_3 NPs dispersions were not toxic.

EuO and Gd-doped EuO thin films. Epitaxial growth and properties

International Nuclear Information System (INIS)

Sutarto, Ronny

2009-01-01

quality of many of the doped EuO samples used in the past bulk studies. The focus of this thesis is on the preparation and the properties of high-quality single-crystalline EuO and Gd-doped EuO thin films. The so-called Eu-distillation-assisted molecular beam epitaxy (MBE) has been employed to achieve full control of the stoichiometry. The films have been epitaxially grown on yttria-stabilized cubic zirconia (YSZ) (001) substrates. By a systematic variation of the oxygen deposition rates, we have been able to observe sustained oscillations in the intensity of the reflection high-electron energy diffraction (RHEED) pattern during growth. We thus have demonstrated that layer-by-layer growth has been achieved for the first time. We also have confirmed that YSZ indeed supplies oxygen during the initial stages of growth, yet the EuO stoichiometry can still be well maintained. In the case of Gd-doped EuO films, the presence of Gd even helps to stabilize the layer-by-layer growth mode. It is important to achieve this growth mode, since it enables the preparation of films with very smooth and at surfaces. This in turn facilitates the capping of the films with a thin Al overlayer in order to protect the films against degradation under ambient conditions. More important, the smoothness of the lm will enable the preparation of high quality device structures. By using ex-situ soft x-ray absorption spectroscopy (XAS) at the Eu and Gd M 4,5 edges, we have confirmed that the films are completely free from Eu 3+ contaminants, and we were able to determine reliably the actual Gd concentration. This actual Gd concentration could in fact significantly deviate from the nominal Gd/Eu evaporation ratio. From magnetization and susceptibility measurements, we found the Curie temperature to increase smoothly as a function of doping from 69 K up to a maximum of 125 K, all with a saturation moment of 7 μB. A threshold behavior was not observed for Gd concentrations as low as 0.2 %. Analysis of the

EuO and Gd-doped EuO thin films. Epitaxial growth and properties

Energy Technology Data Exchange (ETDEWEB)

Sutarto, Ronny

2009-07-06

this respect the quality of many of the doped EuO samples used in the past bulk studies. The focus of this thesis is on the preparation and the properties of high-quality single-crystalline EuO and Gd-doped EuO thin films. The so-called Eu-distillation-assisted molecular beam epitaxy (MBE) has been employed to achieve full control of the stoichiometry. The films have been epitaxially grown on yttria-stabilized cubic zirconia (YSZ) (001) substrates. By a systematic variation of the oxygen deposition rates, we have been able to observe sustained oscillations in the intensity of the reflection high-electron energy diffraction (RHEED) pattern during growth. We thus have demonstrated that layer-by-layer growth has been achieved for the first time. We also have confirmed that YSZ indeed supplies oxygen during the initial stages of growth, yet the EuO stoichiometry can still be well maintained. In the case of Gd-doped EuO films, the presence of Gd even helps to stabilize the layer-by-layer growth mode. It is important to achieve this growth mode, since it enables the preparation of films with very smooth and at surfaces. This in turn facilitates the capping of the films with a thin Al overlayer in order to protect the films against degradation under ambient conditions. More important, the smoothness of the lm will enable the preparation of high quality device structures. By using ex-situ soft x-ray absorption spectroscopy (XAS) at the Eu and Gd M{sub 4,5} edges, we have confirmed that the films are completely free from Eu{sup 3+} contaminants, and we were able to determine reliably the actual Gd concentration. This actual Gd concentration could in fact significantly deviate from the nominal Gd/Eu evaporation ratio. From magnetization and susceptibility measurements, we found the Curie temperature to increase smoothly as a function of doping from 69 K up to a maximum of 125 K, all with a saturation moment of 7 {mu}B. A threshold behavior was not observed for Gd concentrations

Superconductivity and ceramic superconductors II; Proceedings of the Symposium, Orlando, FL, Nov. 12-15, 1990. Ceramic transactions. Vol. 18

International Nuclear Information System (INIS)

Nair, K.M.; Balachandran, U.; Chiang, Y.-M.; Bhalla, A.S.

1991-01-01

The present symposium on superconductivity and ceramic superconductors discusses fundamentals and general principles, powder processing and properties, fabrication and properties, and device reliability and applications. Attention is given to phase formation in the Tl-Ca-Ba-Cu-O system, comparative defect studies in La2CuO4 and La2NiO4, solid solution and defect behavior in high Tc oxides, oxygen ion transport and disorder in cuprates, and Sr-free Bi-Ln-Ca-Cu-O superconductors. Topics addressed include the preparation of superconductor Y-Ba-Cu-O powder by single-step calcining in air, low-temperature synthesis of YBa2Cu3O(7-x), synthesis of high-phase purity ceramic oxide superconductors by the xerogel method, and the preparation and characterization of the BYa2Cu4O8 superconductor. Also discussed are optical studies of humidity-based corrosion effects on thin film and bulk ceramic YBa2Cu3O(7-delta), thermomechanical processing of YBa2Cu3O(x)/Ag sheathed wires, and the expansion of high-Tc superconducting ceramics

The non-commutative topology of two-dimensional dirty superconductors

Science.gov (United States)

De Nittis, Giuseppe; Schulz-Baldes, Hermann

2018-01-01

Non-commutative analysis tools have successfully been applied to the integer quantum Hall effect, in particular for a proof of the stability of the Hall conductance in an Anderson localization regime and of the bulk-boundary correspondence. In this work, these techniques are implemented to study two-dimensional dirty superconductors described by Bogoliubov-de Gennes Hamiltonians. After a thorough presentation of the basic framework and the topological invariants, Kubo formulas for the thermal, thermoelectric and spin Hall conductance are analyzed together with the corresponding edge currents.

Superconducting Dy1-x(Gd,Yb)xBa2Cu3O7-δ thin films made by Chemical Solution Deposition

DEFF Research Database (Denmark)

Opata, Yuri Aparecido; Wulff, Anders Christian; Hansen, Jørn Otto Bindslev

2016-01-01

Dy1-x(Gd or Yb)xBa2Cu3O7-δ samples were prepared using chemical solution deposition (CSD), based on trifluoroacetate metal-organic decomposition (MOD) methods. X-ray diffraction results demonstrated the formation of the RE123 superconducting phase with a strong in-plane and out-of-plane texture. c...

Comprehensive comparison of the levitation performance of bulk YBaCuO arrays above two different types of magnetic guideways

International Nuclear Information System (INIS)

Deng, Zigang; Qian, Nan; Che, Tong; Jin, Liwei; Si, Shuaishuai; Zhang, Ya; Zheng, Jun

2016-01-01

The permanent magnet guideway (PMG) is an important part of high temperature superconducting (HTS) maglev systems. So far, two types of PMG, the normal PMG and Halbach-type PMG, are widely applied in present maglev transportation systems. In this paper, the levitation performance of high temperature superconductor bulks above the two PMGs was synthetically compared. Both static levitation performance and dynamic response characteristics were investigated. Benefiting from the reasonable magnetic field distribution, the Halbach-type PMG is able to gain larger levitation force, greater levitation force decay during the same relaxation time, bigger resonance frequency and dynamic stiffness for the bulk superconductor levitation unit compared with the normal PMG. Another finding is that the Halbach-type PMG is not sensitive to the levitation performance of the bulk levitation unit with different arrays. These results are helpful for the practical application of HTS maglev systems. - Highlights: • The effect of PMG configurations to levitation performances is investigated. • Bigger force and greater force decay are obtained on Halbach-type PMG. • Halbach-type PMG is not sensitive to the levitation force in various bulk arrays. • Practical issues including costs and assembly of PMGs are considered.

Comprehensive comparison of the levitation performance of bulk YBaCuO arrays above two different types of magnetic guideways

Energy Technology Data Exchange (ETDEWEB)

Deng, Zigang, E-mail: deng@swjtu.cn [Applied Superconductivity Laboratory, State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu, 610031 (China); Qian, Nan; Che, Tong; Jin, Liwei [Applied Superconductivity Laboratory, State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu, 610031 (China); Si, Shuaishuai [Applied Superconductivity Laboratory, State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu, 610031 (China); School of Electrical Engineering, Southwest Jiaotong University, Chengdu, 610031 (China); Zhang, Ya; Zheng, Jun [Applied Superconductivity Laboratory, State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu, 610031 (China)

2016-12-15

The permanent magnet guideway (PMG) is an important part of high temperature superconducting (HTS) maglev systems. So far, two types of PMG, the normal PMG and Halbach-type PMG, are widely applied in present maglev transportation systems. In this paper, the levitation performance of high temperature superconductor bulks above the two PMGs was synthetically compared. Both static levitation performance and dynamic response characteristics were investigated. Benefiting from the reasonable magnetic field distribution, the Halbach-type PMG is able to gain larger levitation force, greater levitation force decay during the same relaxation time, bigger resonance frequency and dynamic stiffness for the bulk superconductor levitation unit compared with the normal PMG. Another finding is that the Halbach-type PMG is not sensitive to the levitation performance of the bulk levitation unit with different arrays. These results are helpful for the practical application of HTS maglev systems. - Highlights: • The effect of PMG configurations to levitation performances is investigated. • Bigger force and greater force decay are obtained on Halbach-type PMG. • Halbach-type PMG is not sensitive to the levitation force in various bulk arrays. • Practical issues including costs and assembly of PMGs are considered.

Continuous lengths of oxide superconductors

Science.gov (United States)

Kroeger, Donald M.; List, III, Frederick A.

2000-01-01

A layered oxide superconductor prepared by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon. A continuous length of a second substrate ribbon is overlaid on the first substrate ribbon. Sufficient pressure is applied to form a bound layered superconductor precursor powder between the first substrate ribbon and the second substrate ribbon. The layered superconductor precursor is then heat treated to establish the oxide superconducting phase. The layered oxide superconductor has a smooth interface between the substrate and the oxide superconductor.

Field limit and nano-scale surface topography of superconducting radio-frequency cavity made of extreme type II superconductor

Science.gov (United States)

Kubo, Takayuki

2015-06-01

The field limit of a superconducting radio-frequency cavity made of a type II superconductor with a large Ginzburg-Landau parameter is studied, taking the effects of nano-scale surface topography into account. If the surface is ideally flat, the field limit is imposed by the superheating field. On the surface of cavity, however, nano-defects almost continuously distribute and suppress the superheating field everywhere. The field limit is imposed by an effective superheating field given by the product of the superheating field for an ideal flat surface and a suppression factor that contains the effects of nano-defects. A nano-defect is modeled by a triangular groove with a depth smaller than the penetration depth. An analytical formula for the suppression factor of bulk and multilayer superconductors is derived in the framework of the London theory. As an immediate application, the suppression factor of the dirty Nb processed by electropolishing is evaluated by using results of surface topographic study. The estimated field limit is consistent with the present record field of nitrogen-doped Nb cavities. Suppression factors of surfaces of other bulk and multilayer superconductors, and those after various surface processing technologies, can also be evaluated by using the formula.

How to determine Hc1 of high Tc oxide superconductors

International Nuclear Information System (INIS)

Cao Xiaowen; Huang Sunli

1989-12-01

The magnetizations of cylinder Bi 1.7 Pb 0.3 Sr 2 Ca 2 Cu 3 O y bulk superconductor whose length is shorten step by step has shown that H c1 is independent of the length of cylinder, i.e. independent of the demagnetic factor, as the length is larger than the diameter, whereas it is dependent of demagnetic factor, as the length is smaller than the diameter. But the demagnetization factor is a constant about 1/4 for l< d

Thermally actuated magnetization flux pump in single-grain YBCO bulk

Energy Technology Data Exchange (ETDEWEB)

Yan Yu; Li Quan; Coombs, T A, E-mail: yy300@cam.ac.u, E-mail: ql229@cam.ac.u, E-mail: tac1000@cam.ac.u [EPEC Superconductivity Group, Electrical Engineering Department, Cambridge University, 9 J J Thomson Avenue, Cambridge CB3 0FA (United Kingdom)

2009-10-15

Recent progress in material processing has proved that high temperature superconductors (HTS) have a great potential to trap large magnetic fields at cryogenic temperatures. For example, HTS are widely used in MRI scanners and in magnetic bearings. However, using traditional ways to magnetize, the YBCO will always need the applied field to be as high as the expected field on the superconductor or much higher than it, leading to a much higher cost than that of using permanent magnets. In this paper, we find a method of YBCO magnetization in liquid nitrogen that only requires the applied field to be at the level of a permanent magnet. Moreover, rather than applying a pulsed high current field on the YBCO, we use a thermally actuated material (gadolinium) as an intermedia and create a travelling magnetic field through it by changing the partial temperature so that the partial permeability is changed to build up the magnetization of the YBCO gradually after multiple pumps. The gadolinium bulk is located between the YBCO and the permanent magnet and is heated and cooled repeatedly from the outer surface to generate a travelling thermal wave inwards. In the subsequent experiment, an obvious accumulation of the flux density is detected on the surface of the YBCO bulk.

Thermally actuated magnetization flux pump in single-grain YBCO bulk

International Nuclear Information System (INIS)

Yan Yu; Li Quan; Coombs, T A

2009-01-01

Recent progress in material processing has proved that high temperature superconductors (HTS) have a great potential to trap large magnetic fields at cryogenic temperatures. For example, HTS are widely used in MRI scanners and in magnetic bearings. However, using traditional ways to magnetize, the YBCO will always need the applied field to be as high as the expected field on the superconductor or much higher than it, leading to a much higher cost than that of using permanent magnets. In this paper, we find a method of YBCO magnetization in liquid nitrogen that only requires the applied field to be at the level of a permanent magnet. Moreover, rather than applying a pulsed high current field on the YBCO, we use a thermally actuated material (gadolinium) as an intermedia and create a travelling magnetic field through it by changing the partial temperature so that the partial permeability is changed to build up the magnetization of the YBCO gradually after multiple pumps. The gadolinium bulk is located between the YBCO and the permanent magnet and is heated and cooled repeatedly from the outer surface to generate a travelling thermal wave inwards. In the subsequent experiment, an obvious accumulation of the flux density is detected on the surface of the YBCO bulk.

Bulk superconducting gap of V{sub 3}Si studied by low-energy ultrahigh-resolution photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Sato, T., E-mail: t-sato@arpes.phys.tohoku.ac.jp [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Souma, S. [WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Nakayama, K. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Sugawara, K. [WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Toyota, N. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Takahashi, T. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

2016-04-15

Highlights: • We report ultrahigh-resolution photoemission spectroscopy of A15 compound V{sub 3}Si. • We found a sharp quasiparticle peak due to superconducting-gap opening. • The surface metallic component is negligibly small in the bulk-sensitive measurement. • We show that V{sub 3}Si is a single-gap s-wave superconductor. - Abstract: We have performed low-energy ultrahigh-resolution photoemission spectroscopy (PES) of A15 compound V{sub 3}Si with a xenon-plasma discharge lamp to elucidate the bulk superconducting gap. Below the superconducting transition temperature (T{sub c} = 15.9 K), we found a sharp quasiparticle peak at the Fermi level in the PES spectrum. The gap spectrum is well fitted by a single s-wave superconducting-gap function together with a dip structure at ∼30 meV suggestive of a strong electron-phonon coupling. The anomalous in-gap state previously observed in the PES measurement with high-energy photons is absent or negligibly small in the present bulk-sensitive measurement. The present PES result shows that V{sub 3}Si is a single-gap s-wave superconductor.

Numerical studies on the force characteristic of superconducting linear synchronous motor with HTS bulk magnet

Science.gov (United States)

Tang, Junjie; Li, Jing; Li, Xiang; Han, Le

2018-03-01

High temperature superconductor (HTS) bulks have significant potential use in linear motor application act as quasi-permanent magnet to replace traditional magnets. Force characteristic between HTS bulk magnet and traveling magnetic field was investigated with numerical simulation and experimental measurement in this paper. Influences of bulk height and number on the force characteristic were studied by the finite element model considering the nonlinear E-J relationship. Study was also made on addition of a back iron plate to the bulk magnet. Besides, force characteristic of bulk was compared with the permanent magnet results. The small initial decrease of the thrust could be explained by inside superconducting current redistribution. It was found that efficiency of linear motor did not increase by adding more bulk magnets. The bulk magnet will be remagnetized instead of erasing trapped field with the increase of the traveling magnetic field strength. The conclusions are helpful in prediction and design the linear motor with HTS bulk magnet.

Ni3d-Gd4f correlation effects on the magnetic behaviour of GdNi

Energy Technology Data Exchange (ETDEWEB)

Paulose, P L [Tata Inst. of Fundamental Research, Bombay (India); Patil, Sujata [Tata Inst. of Fundamental Research, Bombay (India); Mallik, R [Tata Inst. of Fundamental Research, Bombay (India); Sampathkumaran, E V [Tata Inst. of Fundamental Research, Bombay (India); Nagarajan, V [Tata Inst. of Fundamental Research, Bombay (India)

1996-07-01

The results of magnetization and heat-capacity measurements on the alloys, Gd{sub 1-x}Y{sub x}Ni (x=0.0, 0.25, 0.5, 0.75 and 0.9) are reported. The data suggest that there is a Gd induced magnetic moment on Ni, which may in turn enhance Gd-Gd exchange interaction strength in GdNi. The induced moment (on Ni) apparently exhibits itinerant ferromagnetism in the magnetically ordered state of GdNi. (orig.).

Applications of high-temperature superconductors in power technology

International Nuclear Information System (INIS)

Hull, John R

2003-01-01

Since the discovery of the first high-temperature superconductors (HTSs) in the late 1980s, many materials and families of materials have been discovered that exhibit superconductivity at temperatures well above 20 K. Of these, several families of HTSs have been developed for use in electrical power applications. Demonstration of devices such as motors, generators, transmission lines, transformers, fault-current limiters, and flywheels in which HTSs and bulk HTSs have been used has proceeded to ever larger scales. First-generation wire, made from bismuth-based copper oxides, was used in many demonstrations. The rapid development of second-generation wire, made by depositing thin films of yttrium-based copper oxide on metallic substrates, is expected to further accelerate commercial applications. Bulk HTSs, in which large single-grain crystals are used as basic magnetic components, have also been developed and have potential for electrical power applications

High pressure studies up to 50 GPa of Bi-based high-Tc superconductors

International Nuclear Information System (INIS)

Staun Olsen, J.; Steenstrup, S.; Gerward, L.; Sundqvist, B.

1991-01-01

The high-T c superconductor with nominal composition BiSrCaCu 2 O x has been studied at high pressure, i.e. up to 50 GPa. A tetragonal structure was compatible with the measurements at all pressures, and no phase change was observed. The bulk modulus, B o =62.5 GPa, obtained has a somewhat smaller value than the one estimated earier. (orig.)

Effect of hydrostatic and chemical pressure on the exchange interaction in magnetic borocarbide superconductors

Science.gov (United States)

Michor, H.; El-Hagary, M.; Naber, L.; Bauer, E.; Hilscher, G.

2000-03-01

The investigation of pair-breaking effects in magnetic rare-earth nickel borocarbide superconductors reveals a considerable increase of the magnetic exchange integral Jsf by hydrostatic as well as chemical pressure. In both, Jsf is governed by the R-C distance (or lattice constant a) and is described quantitatively by a simple phenomenological model. Thereby, just two parameters Jsf0=31 meV and ΔJsf/Δa=165 meV/Å explain well the influence of chemical pressure upon the initial depression rates of Tc in solid solutions R'1-xRxNi2B2C with R=Gd, Tb, Dy, Ho and R'=Y and Lu.

Evaluation of Gd and Gd{sup 159} as new approaches for cancer treatment

Energy Technology Data Exchange (ETDEWEB)

Galvao, I.; Neves, M.J., E-mail: nevesmj@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Grupo de Desenvolvimento de Radiofarmacos; Santos, R.G., E-mail: santosr@cdtn.br [Instituto Nacional de Ciencia e Tecnologia em Medicina Molecular (INCT-MM), Belo Horizonte, MG (Brazil)

2011-07-01

Metal compounds have shown many biological activities and have been successfully used as anticancer agents such cisplatin. Actually gadolinium (Gd) complexed with a porphyrin Motexafin (MGd) has been investigated as redox-active compound for treatment of cancer. 1{sup 59G}d decays by beta emission with an energy of 970 keV and half-life of 18.59 hours. The de-excitation can be via gamma ray and internal conversion electron emission followed by auger electrons and x rays. Considering all of this 1{sup 59G}d could be a interesting radionuclide to be as a radio therapeutical agent. The aims of this works were to evaluate the cytotoxicity of Gd and 1{sup 59G}d on malignant brain tumors such as glioblastoma multiform, the most frequent brain tumors which has a very poor prognosis. For this purpose, it was used human glioblastoma cell lines T98 (mutant p53) and U87 (wild-type p53) to investigate the cytotoxicity of gadolinium on cell metabolism by MTT assay and also morphological changes, chromatin condensation by DAPI assay and ROS generation. Gadolinium was able to decrease cell viability, the cells presented morphological changes like round shapes and blebs formation after cell treatment with 5x10{sup -6}M of Gd. Nuclear changing and ROS generation occurred in a dose dependent way indicating the cytotoxic effect of Gd. Treatment with 1{sup 59G}d increased all of changes observed with treatment with Gd. These results state for an additive effect of metal toxicity and radioactivity inducing ROS generation as the main mechanism of anti tumoral action of 1{sup 59G}d. The results obtained indicated that the radioactive analogues of Gd have increased cytotoxic effects and gadolinium can be a metal of choice for development of new drugs for cancer treatment. (author)

Tunable Majorana corner states in a two-dimensional second-order topological superconductor induced by magnetic fields

Science.gov (United States)

Zhu, Xiaoyu

2018-05-01

A two-dimensional second-order topological superconductor exhibits a finite gap in both bulk and edges, with the nontrivial topology manifesting itself through Majorana zero modes localized at the corners, i.e., Majorana corner states. We investigate a time-reversal-invariant topological superconductor in two dimensions and demonstrate that an in-plane magnetic field could transform it into a second-order topological superconductor. A detailed analysis reveals that the magnetic field gives rise to mass terms which take distinct values among the edges, and Majorana corner states naturally emerge at the intersection of two adjacent edges with opposite masses. With the rotation of the magnetic field, Majorana corner states localized around the boundary may hop from one corner to a neighboring one and eventually make a full circle around the system when the field rotates by 2 π . In the end, we briefly discuss physical realizations of this system.

Strain effects on point defects and chain-oxygen order-disorder transition in 123 cuprate compounds

International Nuclear Information System (INIS)

Su Haibin; Welch, David O.; Wong-Ng, Winnie

2004-01-01

The energetics of Schottky defects in 123 cuprate superconductor series RBa 2 Cu 3 O 7 (where R=lanthandies) and YA 2 Cu 3 O 7 (A=alkali earths), were found to have unusual relations if one considers only the volumetric strain. Our calculations reveal the effect of nonuniform changes of interatomic distances within the R-123 structures, introduced by doping homovalent elements, on the Schottky defect formation energy. The energy of formation of Frenkel pair defects, which is an elementary disordering event, in 123 compounds can be substantially altered under both stress and chemical doping. Scaling the oxygen-oxygen short-range repulsive parameter using the calculated formation energy of Frenkel pair defects, the transition temperature between orthorhombic and tetragonal phases is computed by quasichemical approximations (QCA's). The theoretical results illustrate the same trend as the experimental measurements in that the larger the ionic radius of R, the lower the orthorhombic/tetragonal phase transition temperature. This study provides strong evidence of the strain effects on order-disorder transition due to oxygens in the CuO chain sites

AC susceptibility response of bulk YBCO superconductors in the presence of a temperature gradient

International Nuclear Information System (INIS)

Bodi, A.C.; Kirschner, I.

1997-01-01

Low-frequency AC susceptibility measurements on ceramic YBCO superconductors carried out at the presence of a quasi-one-dimensional temperature gradient are compared with those made without the temperature gradient. The values of the different characteristic temperatures measured on samples without and with a temperature gradient are identical but in the second case its characteristic temperature is a medium value. When the temperature gradient is constant on the sample the arithmetic medium value of the local temperatures is the effective characteristic temperature different phenomena. (orig.)

Chapter 27. Superconductors

International Nuclear Information System (INIS)

Vavra, O.

2007-01-01

In this chapter author deals with superconductors and superconductivity. Different chemical materials used as high-temperature superconductors are presented. Some applications of superconductivity are presented.

Superconductors with excess quasiparticles

International Nuclear Information System (INIS)

Elesin, V.F.; Kopaev, Y.V.

1981-01-01

This review presents a systematic kinetic theory of nonequilibrium phenomena in superconductors with excess quasiparticles created by electromagnetic or tunnel injection. The energy distributions of excess quasiparticles and of nonequilibrium phonons, dependence of the order parameter on the power and frequency (or intensity) of the electromagnetic field, magnetic properties of nonequilibrium superconductors, I-V curves of superconductor-insulator-superconductor junctions, and other properties are described in detail. The stability of superconducting states far from thermodynamic equilibrium is investigated and it is shown that characteristic instabilities leading to the formation of nonuniform states of a new type or phase transitions of the first kind are inherent to superconductors with excess quasiparticles. The results are compared with experimental data

DC magnetization of random Y1Ba2Cu3O8-δ/Ag bulk composites

International Nuclear Information System (INIS)

Ash, C.L.; Harris, D.C.; Calabrese, J.J.; Garland, J.C.

1994-01-01

It is commonly believed that high-field magnetization measurements of superconducting/normal metal bulk composites probe only the intragranular nature of the superconducting constituent. According to this view, the measured magnetic moment divided by the volume of superconducting material should be independent of the volume fraction of superconductor. We have tested this hypothesis by measuring the dc magnetization at 10K in magnetic fields to 5T of a series of YBCO/Ag bulk composites with 0 ≤ p ≤ 1.0, where p is the volume fraction of superconductor. We find that the magnetization hysteresis curves for p ≥ 0.70 are nearly identical, while those for the p < 0.70 samples fall inside the p ≥ 0.70 curves. Two possible interpretations are (i) that variations in Ag content alters the superconducting properties of individual YBCO grains, and (ii) that the p-dependent variations in the YBCO clusters affects the demagnetization factor for samples with p < 0.70. (orig.)

Fabrication and properties of Y-Ba-Cu-O high Tc superconductor by upset-forging method

International Nuclear Information System (INIS)

Chang, Ho Jung; Kang, Kae Myung; Song, Jin Tae

1990-01-01

YBa 2 Cu 3 O 7-x oxide superconductors was fabricated by sintering process and upset-forging method, respectively, and microstructures and conduction properties were compared. There was no difference in crystal structure the (001) x-ray reflection presumably due to preferred crystal orientation of the YBa 2 Cu 3 O 7-x superconductor. Furthermore, the grain size of the 123-phase increased as the reduction ratio became larger during the upset-forging. The critical temperature for zero resistivity of both samples was almost the same, i.e., about 90K. These results have demonstrated the potential of producing YBa 2 Cu 3 O 7-x superconducting wire or tape effectively using a upset-forging method. The critical current density of the upset-forged sample, however, was lower than that of the sintered one, which fact might be ascribed to microcrack formation during fast upset-forging. (Author)

Hybrid molecule/superconductor assemblies

International Nuclear Information System (INIS)

McDevitt, J.T.; Haupt, S.G.; Riley, D.R.; Zhao, J.; Zhou, J.P., Jones, C.

1993-01-01

The fabrication of electronic devices from molecular materials has attracted much attention recently. Schottky diodes, molecular transistors, metal-insulator-semiconductor diodes, MIS field effect transistors and light emitting diodes have all been prepared utilizing such substances. The active elements in these devices have been constructed by depositing the molecular phase onto the surface of a metal, semiconductor or insulating substrate. With the recent discovery of high temperature superconductivity, new opportunities now exist for the study of molecule/superconductor interactions as well as for the construction of novel hybrid molecule/superconductor devices. In this paper, methods for preparing the initial two composite molecule/semiconductor devices will be reported. Consequently, light sensors based on dye-coated superconductor junctions as well as molecular switches fashioned from conductive polymer coated superconductor junctions as well as molecular switches fashioned from conductive polymer coated superconductor microbridges will be discussed. Moreover, molecule/superconductor energy and electron transfer phenomena will be illustrated also for the first time

Switching Magnetism and Superconductivity with Spin-Polarized Current in Iron-Based Superconductor.

Science.gov (United States)

Choi, Seokhwan; Choi, Hyoung Joon; Ok, Jong Mok; Lee, Yeonghoon; Jang, Won-Jun; Lee, Alex Taekyung; Kuk, Young; Lee, SungBin; Heinrich, Andreas J; Cheong, Sang-Wook; Bang, Yunkyu; Johnston, Steven; Kim, Jun Sung; Lee, Jhinhwan

2017-12-01

We explore a new mechanism for switching magnetism and superconductivity in a magnetically frustrated iron-based superconductor using spin-polarized scanning tunneling microscopy (SPSTM). Our SPSTM study on single-crystal Sr_{2}VO_{3}FeAs shows that a spin-polarized tunneling current can switch the Fe-layer magnetism into a nontrivial C_{4} (2×2) order, which cannot be achieved by thermal excitation with an unpolarized current. Our tunneling spectroscopy study shows that the induced C_{4} (2×2) order has characteristics of plaquette antiferromagnetic order in the Fe layer and strongly suppresses superconductivity. Also, thermal agitation beyond the bulk Fe spin ordering temperature erases the C_{4} state. These results suggest a new possibility of switching local superconductivity by changing the symmetry of magnetic order with spin-polarized and unpolarized tunneling currents in iron-based superconductors.

The magnetostriction in a superconductor-magnet system under non-uniform magnetic field

Energy Technology Data Exchange (ETDEWEB)

Li, Xueyi; Jiang, Lang; Wu, Hao [Key Laboratory of Mechanics on Disaster and Environment in Western China attached to the Ministry of Education of China, Lanzhou University, Lanzhou, Gansu 730000 (China); Gao, Zhiwen, E-mail: gaozhw@lzu.edu.cn [Department of Mechanics and Engineering Science, College of Civil Engineering and Mechanics, Lanzhou University, Lanzhou, Gansu 730000 (China)

2017-03-15

Highlights: • We studied firstly magnetostriction in HTS under non-uniform magnetic field. • The superconductors may be homogeneous and nonhomogeneous. • The magnetostrictions response of the HTS is sensitive to the critical current density and amplitude of the applied magnetic field. • The magnetostriction of nonhomogeneous HTS is larger than that of homogeneous HTS. - Abstract: This paper describes a numerical model to examine the magnetostriction of bulk high-temperature superconductor (HTS) under non-uniform magnetic field in conjunction with finite element analysis. Through this model, the magnetostriction of homogeneous and nonhomogeneous HTS can be implemented under non-uniform magnetic field. Further, the effects of critical current density, applied field frequency and amplitude are also considered. The computational study can provide a fundamental mechanistic understanding the effects of non-uniform magnetic field on magnetostriction of HTS.

Investigation of chemical bond characteristics, thermal expansion coefficients and bulk moduli of alpha-R2MoO6 and R2Mo2O7 (R = rare earths) by using a dielectric chemical bond method.

Science.gov (United States)

Li, Huaiyong; Zhang, Siyuan; Zhou, Shihong; Cao, Xueqiang

2009-09-01

Theoretical researches are performed on the alpha-R2MoO6 (R = Y, Gd, Tb Dy, Ho, Er, Tm and Yb) and pyrochlore-type R2Mo2O7 (R = Y, Nd, Sm, Gd, Tb and Dy) rare earth molybdates by using chemical bond theory of dielectric description. The chemical bonding characteristics and their relationship with thermal expansion property and compressibility are explored. The calculated values of linear thermal expansion coefficient (LTEC) and bulk modulus agree well with the available experimental values. The calculations reveal that the LTECs and the bulk moduli do have linear relationship with the ionic radii of the lanthanides: the LTEC decreases from 6.80 to 6.62 10(-6)/K and the bulk modulus increases from 141 to 154 GPa when R goes in the order Gd, Tb Dy, Ho, Er, Tm, and Yb in the alpha-R2MoO6 series; while in the R2Mo2O7 series, the LTEC ranges from 6.80 to 6.61 10(-6)/K and the bulk modulus ranges from 147 to 163 GPa when R varies in the order Nd, Sm, Gd, Tb and Dy. Copyright 2008 Wiley Periodicals, Inc.

Calculation of the band structure of GdCo2, GdRh2 e GdIr2 by the APW method

International Nuclear Information System (INIS)

Carvalho, J.A.B. de.

1974-03-01

The band structure of GdCo 2 , GdRh 2 , GdIr 2 has been calculated by the APW method. A histogram of the density of states is presented for each compound. The bands are transition-metal-like, with s-d hybridization near the Fermi level. The 5d character near the Fermi level increases as one goes from Co to Ir

Far infrared spectroscopy of high-Tc superconductors at the National Synchrotron Light Source

International Nuclear Information System (INIS)

Perkowitz, S.; Williams, G.P.

1989-01-01

This paper reports the first far infrared transmission spectra for micron-thick films of high-T c rare-earth superconductors such as DyBaCuO, with implications for the superconducting gap. Spectra were obtained at Brookhaven's National Synchrotron Light Source, a new high-intensity, broad-band millimeter to infrared source. The National Synchrotron Light Source at Brookhaven National Laboratory, known for powerful X-ray and UV output, is also a high-intensity (10 to 1000 times above a black body), high-brightness (intensity per solid angle), broad-band, picosecond, millimeter to infrared source. These features make it valuable for far-infrared condensed matter experiments, especially those in highly absorbing or extremely small systems. A first application has been to measure very small infrared transmissions through thick bulk-like high-T c superconducting films. Preliminary measurements through films of the conventional superconductor Nb 3 Ge established techniques. These were followed by the first measurements (to the author's knowledge) through micron-thick films of high-T c rare-earth superconductors such as DyBaCuO over 10-300 cm -1 , which includes the superconducting gap according to BCS or moderately strong-coupled theory. The authors discuss the transmission evidence bearing on the existence of a gap and other important features of high-T c superconductors, and describe the synchrotron and instrumentation features which make possible these unusual measurements

Mono-domain YBa2Cu3Oy superconductor fabrics prepared by an infiltration process

International Nuclear Information System (INIS)

Sudhakar Reddy, E.; Noudem, J.G.; Tarka, M.; Schmitz, G.J.

2000-01-01

A novel process for the fabrication of a new form of YBa 2 Cu 3 O y (123) superconducting material, with the dimensions of a thick film and the microstructure of a melt-textured single-domain bulk is described. The process allows the fabrication of 123 as a self-supporting fabric or as a thick film on various substrate materials. The process, which is generic and economical, uses commercially available Y 2 O 3 fabrics as a precursor material. The Y 2 O 3 cloth is infiltrated with barium cuprates and copper oxides from a liquid-phase source, then converted into Y 2 BaCuO 5 (211) phase and eventually to 123. The nucleation and growth of the 123 phase is controlled by seeding the cloth with an oriented heterogeneous MgO or Nd123 seed. Interesting application areas for the new form of the 123 mono-domain fabric are discussed. (author)

Magnetic, superconducting and electron-boson properties of GdO(F)FeAs oxypnictides

Science.gov (United States)

Kuzmicheva, Tatiana; Sadakov, Andrey; Muratov, Andrei; Kuzmichev, Svetoslav; Khlybov, Yevgeny; Kulikova, Lyudmila; Eltsev, Yuri

2018-05-01

We performed comprehensive studies of nearly optimal fluorine-substituted GdO1-xFx FeAs oxypnictide superconductors with TC = 48 - 53 K . Specific heat measurements revealed a sharp peak at T = 3.5 K that shifts to lower temperatures with magnetic field increase. This peak corresponds to an antiferromagnetic ordering in Gd3+ ion sublattice and may indicate coexistence between superconducting and magnetic orderings. Andreev transport through artificially made constriction demonstrated two channels for the carriers from the band(s) with the large superconducting gap as well as from those with the small gap. As expected, the presence of a transport channel with the bands mixing (ΔL +ΔS) was not detected. Using intrinsic multiple Andreev reflections effect (IMARE) spectroscopy, we determined two superconducting gaps, ΔS ≈ 2.7 meV , and ΔL ≈ 11.6 meV . The reproducible fine structure in the dI(V)/dV spectra of the Andreev contacts (satellites of the main subharmonic gap structure for ΔL) was interpreted as caused by a resonant emission of bosons with the energy ε0 = 12 - 15 meV ≈ΔL +ΔS during the process of multiple Andreev reflections (MAR) for normal carriers in ΔL-band(s) transport channel.

Suppression of surface barriers in superconductors by columnar defects

International Nuclear Information System (INIS)

Koshelev, A. E.; Vinokur, V. M.

2001-01-01

We investigate the influence of columnar defects in layered superconductors on the thermally activated penetration of pancake vortices through the surface barrier. Columnar defects, located near the surface, facilitate penetration of vortices through the surface barrier, by creating ''weak spots,'' through which pancakes can penetrate into the superconductor. Penetration of a pancake mediated by an isolated column, located near the surface, is a two-stage process involving hopping from the surface to the column and the detachment from the column into the bulk; each stage is controlled by its own activation barrier. The resulting effective energy is equal to the maximum of those two barriers. For a given external field there exists an optimum location of the column for which the barriers for the both processes are equal and the reduction of the effective penetration barrier is maximal. At high fields the effective penetration field is approximately 2 times smaller than in unirradiated samples. We also estimate the suppression of the effective penetration field by column clusters. This mechanism provides further reduction of the penetration field at low temperatures

Fabrication mechanism of FeSe superconductors with high-energy ball milling aided sintering process

International Nuclear Information System (INIS)

Zhang, Shengnan; Liu, Jixing; Feng, Jianqing; Wang, Yao; Ma, Xiaobo; Li, Chengshan; Zhang, Pingxiang

2015-01-01

FeSe Superconducting bulks with high content of superconducting PbO-type β-FeSe phase were prepared with high-energy ball milling (HEBM) aided sintering process. During this process, precursor powders with certain Fe/Se ratio were ball milled first then sintered. The influences of HEBM process as well as initial Fe/Se ratio on the phase evolution process were systematically discussed. With HEBM process and proper initial Fe/Se ratio, the formation of non-superconducting hexagonal δ-FeSe phase were effectively avoided. FeSe bulk with the critical temperature of 9.0 K was obtained through a simple one-step sintering process with lower sintering temperature. Meanwhile, the phase evolution mechanism of the HEBM precursor powders during sintering was deduced based on both the thermodynamic analysis and step-by-step sintering results. The key function of the HEBM process was to provide a high uniformity of chemical composition distribution, thus to successfully avoide the formation of intermediate product during sintering, including FeSe 2 and Fe 7 Se 8 . Therefore, the fundamental principal for the synthesis of FeSe superconductors were concluded as: HEBM aided sintering process, with the sintering temperature of >635 °C and a slow cooling process. - Highlights: • A novel synthesis technique was developed for FeSe based superconductors. • FeSe bulks with high Tc and high β-FeSe phase content has been obtained. • Phase evolution process for the HEBM aided sintering process was proposed

Two classes of superconductors discovered in our material research: Iron-based high temperature superconductor and electride superconductor

International Nuclear Information System (INIS)

Hosono, Hideo

2009-01-01

We discovered two new classes of superconductors in the course of material exploration for electronic-active oxides. One is 12CaO . 7Al 2 O 3 crystal in which electrons accomodate in the crystallographic sub-nanometer-sized cavities. This material exhibiting metal-superconductor transition at 0.2 K is the first electride superconductor. The other is iron oxypnicitides with a layered structure. This superconductor is rather different from high T c cuprates in several respects. The high T c is emerged by doping carriers to the metallic parent phases which undergo crystallographic transition (tetra to ortho) and Pauli para to antiferromagnetic transition at ∼150 K. The T c is robust to impurity doping to the Fe sites or is induced by partial substitution of the Fe 2+ sites with Co 2+ or Ni 2+ . This article gives a brief summary of these discoveries and recent advances.

Formation of YxNd1-xBa2Cu3O7-δ (0≤x≤0.9) superconductors from an undercooled melt via aero-acoustic levitation

International Nuclear Information System (INIS)

Gustafson, D.E.; Hofmeister, W.H.; Bayuzick, R.J.; Nagashio, K.; Kuribayashi, K.

2003-01-01

This paper presents the results of rapid solidification experiments performed on the copper oxide superconductors Y x Nd 1-x Ba 2 Cu 3 O 7-δ (0≤x≤0.9). Spherical rare earth (RE) 123 specimens were levitated in O 2 using aero-acoustic levitation (AAL), melted with a laser, undercooled, and solidified. The peritectic transformation temperature for the reaction RE 2 BaCuO 5 +liquid→REBa 2 Cu 3 O 7-δ corresponding to the maximum recalescence temperature during solidification was determined. RE123 was formed directly from the melt for Y-Nd binary alloy compositions with Nd concentration greater than 20% (Y concentration less than 80%). A minimum in the peritectic transformation temperature for the Nd/Y123 system corresponding to a composition Y 0.3 Nd 0.7 123 was determined at 66 deg. C below the peritectic of pure Nd123

Rare-Earth Surface Alloying: A New Phase for GdAu2

International Nuclear Information System (INIS)

Corso, M.; Schiller, F.; Fernandez, L.; Verstraete, M. J.; Ormaza, M.; Greber, T.; Torrent, M.; Rubio, A.; Ortega, J. E.

2010-01-01

Surface alloying is a powerful way of varying physical and chemical properties of metals, for a number of applications from catalysis to nuclear and green technologies. Surfaces offer many degrees of freedom, giving rise to new phases that do not have a bulk counterpart. However, the atomic characterization of distinct surface compounds is a major task, which demands powerful experimental and theoretical tools. Here we illustrate the process for the case of a GdAu 2 surface phase of extraordinary crystallinity. The combined use of surface-sensitive techniques and state-of-the-art ab initio calculations disentangles its atomic and electronic properties. In particular, the stacking of the surface layers allows for gadolinium's natural ferromagnetic state, at variance with the bulk phase, where frustration leads to antiferromagnetic interlayer coupling.

Strong nonequilibrium coherent states in mesoscopic superconductor-semiconductor-superconductor junctions

DEFF Research Database (Denmark)

Kutchinsky, Jonatan; Wildt, Morten; Taboryski, Rafael Jozef

1999-01-01

A biased superconductor-normal metal-superconductor junction is known to be a strong nonequilibrium system, where Andreev scattering at the interfaces creates a quasiparticle distribution function far from equilibrium, a manifestation of this is the well-known subgap structure in the I...

Characterization of the insulator barrier and the superconducting transition temperature in GdBa2Cu3O7−δ/BaTiO3 bilayers for application in tunnel junctions

International Nuclear Information System (INIS)

Navarro, H.; Sirena, M.; Haberkorn, N.; Yang, Ilkyu; Kim, Jeehoon

2015-01-01

The optimization of the superconducting properties in a bottom electrode and the quality of an insulator barrier are the first steps in the development of superconductor/insulator/superconductor tunnel junctions. Here, we study the quality of a BaTiO 3 tunnel barrier deposited on a 16 nm thick GdBa 2 Cu 3 O 7−δ thin film by using conductive atomic force microscopy. We find that the tunnel current is systematically reduced (for equal applied voltage) by increasing the BaTiO 3 barrier thickness between 1.6 and 4 nm. The BaTiO 3 layers present an energy barrier of ≈1.2 eV and an attenuation length of 0.35–0.5 nm (depending on the applied voltage). The GdBa 2 Cu 3 O 7−δ electrode is totally covered by a BaTiO 3 thickness above 3 nm. The presence of ferroelectricity was verified by piezoresponse force microscopy for a 4 nm thick BaTiO 3 top layer. The superconducting transition temperature of the bilayers is systematically suppressed by increasing the BaTiO 3 thickness. This fact can be associated with stress at the interface and a reduction of the orthorhombicity of the GdBa 2 Cu 3 O 7−δ . The reduction in the orthorhombicity is expected by considering the interface mismatch and it can also be affected by reduced oxygen stoichiometry (poor oxygen diffusion across the BaTiO 3 barrier)

Microwave-induced combustion synthesis and electrical conductivity of Ce1-xGd xO2-1/2x ceramics

International Nuclear Information System (INIS)

Fu, Y.-P.; Chang, Y.-S.; Wen, S.-B.

2006-01-01

Ce 1-x Gd x O 2-1/2x nanopowder were successfully synthesized by microwave-induced combustion process. For the preparation, cerium nitrate, gadolinium nitrate hexahydrate, and urea were used for the microwave-induced combustion process. The process took only 30 min to obtain Ce 1-x Gd x O 2-1/2x powders. The exo-endo temperature, phase identification, and morphology of resultant powders were investigated by TG/DTA, XRD, and SEM. The as-received Ce 1-x Gd x O 2-1/2x powders showed that the average particle size ranged from 18 to 50 nm, crystallite dimension varied from 11 to 20 nm, and the specific surface area was distribution from 16 to 46 m 2 /g. As for Ce 1-x Gd x O 2-1/2x ceramics sintered at 1450 deg. C for 3 h, the bulk density of Ce 1-x Gd x O 2-1/2x ceramics were over 91% of the theoretical density, the maximum electrical conductivity, σ 700deg.C = 0.017 S/cm with minimum activation energy, E a = 0.869 eV was found at Ce 0.80 Gd 0.20 O 1.90 ceramic

Quasiparticle current in superconductor-semiconductor-superconductor junctions

International Nuclear Information System (INIS)

Tartakovskij, A.V.; Fistul', M.V.

1988-01-01

It is shown that the quasiparticle current in a superconductor-semiconductor-superconductor junction may significantly increase as a result of resonant passage of the quasiparticle along particular trajectories from periodically situated localized centers. A prediction of the theory is that with increasing junction resistance there should be a change from an excessive current to a insufficient current on the current-voltage characteristics (at high voltages). The effect of transparency of the boundaries on resonance tunneling in such junctions is also investigated

Microscopic unravelling of nano-carbon doping in MgB2 superconductors fabricated by diffusion method

International Nuclear Information System (INIS)

Wong, D.C.K.; Yeoh, W.K.; De Silva, K.S.B.; Kondyurin, A.; Bao, P.; Li, W.X.; Xu, X.; Peleckis, G.; Dou, S.X.; Ringer, S.P.; Zheng, R.K.

2015-01-01

Highlights: • First report on nano-carbon doped MgB 2 superconductors synthesized by diffusion method. • Microstructure and superconducting properties of the superconductors are discussed. • B 4 C region blocks the Mg from reacting with B in the 10% nano-carbon doped sample. • MgB 2 with 2.5% nano-carbon doped showed the highest J c , ≈10 4 A/cm 2 for 20 K at 4 T. - Abstract: We investigated the effects of nano-carbon doping as the intrinsic (B-site nano-carbon substitution) and extrinsic (nano-carbon derivatives) pinning by diffusion method. The contraction of the in-plane lattice confirmed the presence of disorder in boron sublattice caused by carbon substitution. The increasing value in full width half maximum (FWHM) in the X-ray diffraction (XRD) patterns with each increment in the doping level reveal smaller grains and imperfect MgB 2 crystalline. The strain increased across the doping level due to the carbon substitution in the MgB 2 matrix. The broadening of the T c curves from low to high doping showed suppression of the connectivity of the bulk samples with progressive dirtying. At high doping, the presence of B 4 C region blocked the Mg from reacting with crystalline B thus hampering the formation of MgB 2 . Furthermore, the unreacted Mg acted as a current blocking phase in lowering down the grain connectivity hence depressing the J c of the 10% nano-carbon doped MgB 2 bulk superconductor

RF properties of high-T/sub c/ superconductors

International Nuclear Information System (INIS)

Bohn, C.L.; Delayen, J.R.; Dos Santos, D.I.; Lanagan, M.T.; Shepard, K.W.

1988-01-01

We have investigated the rf properties of high-T/sub c/ superconductors over a wide range of temperature, frequency, and rf field amplitude. We have tested both bulk polycrystalline samples and thick films on silver substrates. At 150 MHz and 4.2 K, we have measured a surface resistance of 18 μ/sup /OMEGA// at low rf field and 3.6 m/sup /OMEGA// at an rf field of 270 gauss. All samples showed a strong dependence of the surface resistance on rf field; however, no breakdown of the superconducting state has been observed up to the highest field achieved (320 gauss). 9 refs., 4 figs., 1 tab

Effect of Al2Gd on microstructure and properties of laser clad Mg–Al–Gd coatings

International Nuclear Information System (INIS)

Chen, Hong; Zhang, Ke; Yao, Chengwu; Dong, Jie; Li, Zhuguo; Emmelmann, Claus

2015-01-01

Highlights: • Mg–Al–Gd coatings with different Gd contents were fabricated by fiber laser cladding. • Chemical compositions and crystal structures of the second phases were characterized. • Dispersion of Al 2 Gd led to further grain refining and elevated mechanical properties. • Al 2 Gd improved high-temperature performances by preventing tiny liquation. - Abstract: In order to investigate the effects of Gd addition on the microstructures and properties of magnesium coatings, the Mg–7.5Al–xGd (x = 0, 2.5, 5.0 and 7.5 wt.%) coatings on cast magnesium alloy were fabricated by laser cladding with wire feeding. The results indicated that the gadolinium (Gd) addition led to the formation of a cubic Al 2 Gd phase as well as suppressed the precipitation of eutectic Mg 17 Al 12 phase. The laser clad coating containing nominally 7.5 wt.% Gd presented the highest microhardness, ultimate tensile strength and yield strength at both room temperature and high temperatures. The enhancement of heat resistant capacities was chiefly attributed to the existence of thermally stable Al 2 Gd particles, which prevented tiny liquation of eutectic phases along the grain boundaries and made great contributions on maintaining high yield ratio during high-temperature deformation

Some experimental and theoretical aspects of the surface impedance in bulk high-temperature superconductors at 10 GHz

Energy Technology Data Exchange (ETDEWEB)

Deville, A.; Fawaz, H.; Gaillard, B. (Lab. d' Electronique des Milieux Condenses, Univ. de Provence, Centre Saint-Jerome, 13 - Marseille (France)); Noel, H.; Potel, M. (Lab. de Chimie Minerale, Univ. de Rennes, 35 (France)); Monnereau, O. (Lab. de Chimie des Materiaux, Univ. de Provence, Centre Saint-Charles, 13 - Marseille (France))

1992-07-15

After a presentation of the theoretical framework, and a short review of existing r.f. results in high-temperature superconductors, we present our own 10 GHz measurements on YBa[sub 2]Cu[sub 3]O[sub 7] single crystals and sintered samples. We use an electron spin resonance (ESR) heterodyne spectrometer and measurements of the reflection coefficient and resonant frequency of a cavity to get information not only on the surface resistance, R[sub S], as generally done, but also on the surface reactance, X[sub S]. The theoretical analysis of the frequency shift is made by adapting Slater's perturbation method to the present problem. In order to explain both the R[sub s] and X[sub S] results, and previous ESR observations, while keeping theoretical simplicity, we are led to suggest that in the normal state these materials show an unconventional skin effect, where the phenomenon is governed not by the d.c. conductivity, but by an effective (lower) conductivity, the other characteristics being unchanged. We briefly discuss the superconductor results and the validity of the two-fluid model. (orig.).

Coupling spin qubits via superconductors

DEFF Research Database (Denmark)

Leijnse, Martin; Flensberg, Karsten

2013-01-01

We show how superconductors can be used to couple, initialize, and read out spatially separated spin qubits. When two single-electron quantum dots are tunnel coupled to the same superconductor, the singlet component of the two-electron state partially leaks into the superconductor via crossed...... Andreev reflection. This induces a gate-controlled singlet-triplet splitting which, with an appropriate superconductor geometry, remains large for dot separations within the superconducting coherence length. Furthermore, we show that when two double-dot singlet-triplet qubits are tunnel coupled...... to a superconductor with finite charging energy, crossed Andreev reflection enables a strong two-qubit coupling over distances much larger than the coherence length....

A comparison of Gd-BOPTA and Gd-DOTA for contrast-enhanced MRI of intracranial tumours

International Nuclear Information System (INIS)

Colosimo, C.; Knopp, M.V.; Barreau, X.; Gerardin, E.; Kirchin, M.A.; Guezenoc, F.; Lodemann, K.P.

2004-01-01

A two-centre intra-individual crossover study was performed in 23 patients with suspected high-grade glioma or metastases to assess and compare the safety and enhancement characteristics of two different MRI contrast media (gadobenate dimeglumine, Gd-BOPTA and gadoterate meglumine, Gd-DOTA) at equivalent doses of 0.1 mmol/kg body weight. T1-weighted spin-echo (SE) and T2-weighted fast SE images were obtained before and T1-weighted images 0, 2, 4, 6, 8 and 15 min after injection. T1-weighted images with magnetisation transfer contrast were acquired 12 min after injection. Qualitative assessment by blinded, off-site readers (reader 1: 19 patients; reader 2: 21) and on-site investigators (23) revealed significant (P ≤0.005) overall preference for Gd-BOPTA over Gd-DOTA for contrast enhancement (Gd-BOPTA preferred in 18, 15 and 18 cases; Gd-DOTA in 0, 1 and 1 and no preference in 1, 5 and 4; off-site readers 1 and 2, and on-site investigators, respectively). A similar significant preference for Gd-BOPTA was expressed by off-site readers and on-site investigators for lesion-to-brain contrast, lesion delineation, internal lesion structure, and overall image preference. Quantitative assessment by off-site readers revealed significantly (p<0.05) greater lesion enhancement with Gd-BOPTA than with Gd-DOTA at all times from 2 min after injection. (orig.)

Practical superconductor development for electrical power applications. Quarterly report for the period ending March 31, 2000

International Nuclear Information System (INIS)

2000-01-01

This is a multiyear experimental research program focused on improving relevant material properties of high-T c superconductors (HTSs) and on development of fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne program. Recent results are presented on YBa 2 Cu 3 O x (Y-123) coated conductors, sheathed (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O x (Bi-2223) tapes, and applications development