WorldWideScience

Sample records for fusion energy targets

  1. Target injection methods for inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Petzoldt, R.W.; Moir, R.W.

    1994-06-01

    We have studied four methods to inject IFE targets: the gas gun, electrostatic accelerator, induction accelerator, and rail gun. We recommend a gas gun for indirect drive targets because they can support a gas pressure load on one end and can slide along the gun barrel without damage. With the gas gun, the amount of gas required for each target (about 10 to 100 mg) is acceptable; for other types of targets, a sabot would be necessary. A cam and poppet valve arrangement is recommended for gas flow control. An electrostatic accelerator is attractive for use with lightweight spherical direct drive targets. Since there is no physical contact between the target and the injector, there will be no wear of either component during the injection process. An induction accelerator has an advantage of no electrical contact between the target and the injector. Physical contact is not even necessary, so the wear should be minimal. It requires a cylindrical conductive target sleeve which is a substantial added mass. A rail gun is a simpler device than an electrostatic accelerator or induction accelerator. It requires electrical contact between the target and the rails and may have a significant wear rate. The wear in a vacuum could be reduced by use of a solid lubricant such as MoS{sub 2}. The total required accuracy of target injection, tracking and beam pointing of {plus_minus}0.4 mm appears achievable but will require development and experimental verification.

  2. Target injection methods for inertial fusion energy

    Science.gov (United States)

    Petzoldt, Ronald W.; Moir, Ralph W.

    1994-06-01

    We have studied four methods to inject IFE targets: the gas gun, electrostatic accelerator, induction accelerator, and rail gun. We recommend a gas gun for indirect drive targets because they can support a gas pressure load on one end and can slide along the gun barrel without damage. With the gas gun, the amount of gas required for each target (about 10 to 100 mg) is acceptable; for other types of targets, a sabot would be necessary. A cam and poppet valve arrangement is recommended for gas flow control. An electrostatic accelerator is attractive for use with lightweight spherical direct drive targets. Since there is no physical contact between the target and the injector, there will be no wear of either component during the injection process. An induction accelerator has an advantage of no electrical contact between the target and the injector. Physical contact is not even necessary, so the wear should be minimal. It requires a cylindrical conductive target sleeve which is a substantial added mass. A rail gun is a simpler device than an electrostatic accelerator or induction accelerator. It requires electrical contact between the target and the rails and may have a significant wear rate. The wear in a vacuum could be reduced by use of a solid lubricant such as MoS2. The total required accuracy of target injection, tracking and beam pointing of +/- 0.4 mm appears achievable but will require development and experimental verification.

  3. Chamber and target technology development for inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Abdou, M; Besenbruch, G; Duke, J; Forman, L; Goodin, D; Gulec, K; Hoffer, J; Khater, H; Kulcinsky, G; Latkowski, J F; Logan, B G; Margevicious, B; Meier, W R; Moir, R W; Morley, N; Nobile, A; Payne, S; Peterson, P F; Peterson, R; Petzoldt, R; Schultz, K; Steckle, W; Sviatoslavsky, L; Tillack, M; Ying, A

    1999-04-07

    Fusion chambers and high pulse-rate target systems for inertial fusion energy (IFE) must: regenerate chamber conditions suitable for target injection, laser propagation, and ignition at rates of 5 to 10 Hz; extract fusion energy at temperatures high enough for efficient conversion to electricity; breed tritium and fuel targets with minimum tritium inventory; manufacture targets at low cost; inject those targets with sufficient accuracy for high energy gain; assure adequate lifetime of the chamber and beam interface (final optics); minimize radioactive waste levels and annual volumes; and minimize radiation releases under normal operating and accident conditions. The primary goal of the US IFE program over the next four years (Phase I) is to develop the basis for a Proof-of-Performance-level driver and target chamber called the Integrated Research Experiment (IRE). The IRE will explore beam transport and focusing through prototypical chamber environment and will intercept surrogate targets at high pulse rep-rate. The IRE will not have enough driver energy to ignite targets, and it will be a non-nuclear facility. IRE options are being developed for both heavy ion and laser driven IFE. Fig. 1 shows that Phase I is prerequisite to an IRE, and the IRE plus NIF (Phase II) is prerequisite to a high-pulse rate. Engineering Test Facility and DEMO for IFE, leading to an attractive fusion power plant. This report deals with the Phase-I R&D needs for the chamber, driver/chamber interface (i.e., magnets for accelerators and optics for lasers), target fabrication, and target injection; it is meant to be part of a more comprehensive IFE development plan which will include driver technology and target design R&D. Because of limited R&D funds, especially in Phase I, it is not possible to address the critical issues for all possible chamber and target technology options for heavy ion or laser fusion. On the other hand, there is risk in addressing only one approach to each technology

  4. Inertial fusion target development for ignition and energy

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, K.R. [General Atomics, San Diego, CA (United States); Norimatsu, T. [Osaka Univ. (Japan). Inst. of Laser Engineering

    1994-12-01

    The target needs of the next ICF experiments that will lead toward ignition and energy are different from those of today`s experiments. The future experiments on OMEGA Upgrade, GEKKO XII Upgrade, the National Ignition Facility and Megajoule will need large, precise, cryogenic targets. Development is needed on a number of aspects of these targets, including shell fabrication, characterization, cryogenic layering and target handling. However, coordinated R and D programs are in place and work is in process to carry out the needed development. It is vital to the success of inertial fusion that this work be sustained. Coordinated effort, like the National Cryogenic Target Program in the USA, will help make the development activities as efficient and effective as possible, and should be encouraged.

  5. FY-2013 FES (Fusion Energy Sciences) Joint Research Target Report

    Energy Technology Data Exchange (ETDEWEB)

    Fenstermacher, M. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Garofalo, A. M. [General Atomics, San Diego, CA (United States); Gerhardt, S. P. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Hubbard, A. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Maingi, R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Whyte, D. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2013-09-30

    The H-mode confinement regime is characterized by a region of good thermal and particle confinement at the edge of the confined plasma, and has generally been envisioned as the operating regime for ITER and other next step devices. This good confinement is often interrupted, however, by edge-localized instabilities, known as ELMs. On the one hand, these ELMs provide particle and impurity flushing from the plasma core, a beneficial effect facilitating density control and stationary operation. On the other hand, the ELMs result in a substantial fraction of the edge stored energy flowing in bursts to the divertor and first wall; this impulsive thermal loading would result in unacceptable erosion of these material surfaces if it is not arrested. Hence, developing and understanding operating regimes that have the energy confinement of standard Hmode and the stationarity that is provided by ELMs, while at the same time eliminating the impulsive thermal loading of large ELMs, is the focus of the 2013 FES Joint Research Target (JRT): Annual Target: Conduct experiments and analysis on major fusion facilities, to evaluate stationary enhanced confinement regimes without large Edge Localized Modes (ELMs), and to improve understanding of the underlying physical mechanisms that allow acceptable edge particle transport while maintaining a strong thermal transport barrier. Mechanisms to be investigated can include intrinsic continuous edge plasma modes and externally applied 3D fields. Candidate regimes and techniques have been pioneered by each of the three major US facilities (C-Mod, D3D and NSTX). Coordinated experiments, measurements, and analysis will be carried out to assess and understand the operational space for the regimes. Exploiting the complementary parameters and tools of the devices, joint teams will aim to more closely approach key dimensionless parameters of ITER, and to identify correlations between edge fluctuations and transport. The role of rotation will be

  6. FY-2013 FES (Fusion Energy Sciences) Joint Research Target Report

    Energy Technology Data Exchange (ETDEWEB)

    Fenstermacher, M. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Garofalo, A. M. [General Atomics, San Diego, CA (United States); Gerhardt, S. P. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Hubbard, A. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Maingi, R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Whyte, D. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2013-09-30

    The H-mode confinement regime is characterized by a region of good thermal and particle confinement at the edge of the confined plasma, and has generally been envisioned as the operating regime for ITER and other next step devices. This good confinement is often interrupted, however, by edge-localized instabilities, known as ELMs. On the one hand, these ELMs provide particle and impurity flushing from the plasma core, a beneficial effect facilitating density control and stationary operation. On the other hand, the ELMs result in a substantial fraction of the edge stored energy flowing in bursts to the divertor and first wall; this impulsive thermal loading would result in unacceptable erosion of these material surfaces if it is not arrested. Hence, developing and understanding operating regimes that have the energy confinement of standard H-mode and the stationarity that is provided by ELMs, while at the same time eliminating the impulsive thermal loading of large ELMs, is the focus of the 2013 FES Joint Research Target (JRT): Annual Target: Conduct experiments and analysis on major fusion facilities, to evaluate stationary enhanced confinement regimes without large Edge Localized Modes (ELMs), and to improve understanding of the underlying physical mechanisms that allow acceptable edge particle transport while maintaining a strong thermal transport barrier. Mechanisms to be investigated can include intrinsic continuous edge plasma modes and externally applied 3D fields. Candidate regimes and techniques have been pioneered by each of the three major US facilities (C-Mod, D3D and NSTX). Coordinated experiments, measurements, and analysis will be carried out to assess and understand the operational space for the regimes. Exploiting the complementary parameters and tools of the devices, joint teams will aim to more closely approach key dimensionless parameters of ITER, and to identify correlations between edge fluctuations and transport. The role of rotation will be

  7. Thermal Studies of the Laser Inertial Fusion Energy (LIFE) Target during Injection into the Fusion Chamber

    Energy Technology Data Exchange (ETDEWEB)

    Miles, R. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Havstad, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); LeBlanc, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chang, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Golosker, I. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rosso, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2014-09-09

    The tests of the external heat transfer coefficient suggests that the values used in the numerical analysis for the temperature distribution within the fusion fuel target following flight into the target chamber are probably valid. The tests of the heat transfer phenomena occurring within the target due the rapid heating of the LEH window for the hot gasses within the fusion chamber show that the heat does indeed convect via the internal helium environment of the target towards the capsule and that the pressure in the front compartment of the target adjacent to the LEH window increases such that t bypass venting of the internal helium into the second chamber adjacent to the capsule is needed to prevent rupture of the membranes. The bypass flow is cooled by the hohlraum during this venting. However, the experiments suggest that our internal heat flow calculations may be low by about a factor of 2. Further studies need to be conducted to investigate the differences between the experiment and the numerical analysis. Future studies could also possibly bring the test conditions closer to those expected in the fusion chamber to better validate the results. A sacrificial layer will probably be required on the LEH window of the target and this can be used to mitigate any unexpected target heating.

  8. Magnetized target fusion: An ultra high energy approach in an unexplored parameter space

    Energy Technology Data Exchange (ETDEWEB)

    Lindemuth, I.R.

    1994-12-31

    Magnetized target fusion is a concept that may lead to practical fusion applications in a variety of settings. However, the crucial first step is to demonstrate that it works as advertised. Among the possibilities for doing this is an ultrahigh energy approach to magnetized target fusion, one powered by explosive pulsed power generators that have become available for application to thermonuclear fusion research. In a collaborative effort between Los Alamos and the All-Russian Scientific Institute for Experimental Physics (VNIIEF) a very powerful helical generator with explosive power switching has been used to produce an energetic magnetized plasma. Several diagnostics have been fielded to ascertain the properties of this plasma. We are intensively studying the results of the experiments and calculationally analyzing the performance of this experiment.

  9. Inertial fusion energy target injection, tracking, and beam pointing

    Energy Technology Data Exchange (ETDEWEB)

    Petzoldt, Ronald Wayne [Univ. of California, Davis, CA (United States)

    1995-03-07

    Several cryogenic targets must be injected each second into a reaction chamber. Required target speed is about 100 m/s. Required accuracy of the driver beams on target is a few hundred micrometers. Fuel strength is calculated to allow acceleration in excess of 10,000 m/s2 if the fuel temperature is less than 17 K. A 0.1 μm thick dual membrane will allow nearly 2,000 m/s2 acceleration. Acceleration is gradually increased and decreased over a few membrane oscillation periods (a few ms), to avoid added stress from vibrations which could otherwise cause a factor of two decrease in allowed acceleration. Movable shielding allows multiple targets to be in flight toward the reaction chamber at once while minimizing neutron heating of subsequent targets. The use of multiple injectors is recommended for redundancy which increases availability and allows a higher pulse rate. Gas gun, rail gun, induction accelerator, and electrostatic accelerator target injection devices are studied, and compared. A gas gun is the preferred device for indirect-drive targets due to its simplicity and proven reliability. With the gas gun, the amount of gas required for each target (about 10 to 100 mg) is acceptable. A revolver loading mechanism is recommended with a cam operated poppet valve to control the gas flow. Cutting vents near the muzzle of the gas gun barrel is recommended to improve accuracy and aid gas pumping. If a railgun is used, we recommend an externally applied magnetic field to reduce required current by an order of magnitude. Optical target tracking is recommended. Up/down counters are suggested to predict target arrival time. Target steering is shown to be feasible and would avoid the need to actively point the beams. Calculations show that induced tumble from electrostatically steering the target is not excessive.

  10. Shock Ignition Target Design for Inertial Fusion Energy

    Science.gov (United States)

    2010-01-01

    on the outer and inner surfaces with “ NIF -spec” spectra4 with nominal amplitudes of 0.48 µm and 1.0 µm respectively, and was subject to laser...hot spot energy is: Eh [kJ] = 9.54×105ρR 3T 3p−2hGbar. ( A1 ) T and ρR are the quantities Tion and ρRh normalized to the nominal values 5 keV and 0.3g/cm2...calculated by using Eqn. (A3). First, rewrite the hot-spot energy equation ( A1 ) as modified by the relation Φ = Φ(p): Eh = 41 ρR 3T α6/5p−6/5. (A19) Then the

  11. Direct drive target survival during injection in an inertial fusion energy power plant

    Science.gov (United States)

    Petzoldt, R. W.; Goodin, D. T.; Nikroo, A.; Stephens, E.; Siegel, N.; Alexander, N. B.; Raffray, A. R.; Mau, T. K.; Tillack, M.; Najmabadi, F.; Krasheninnikov, S. I.; Gallix, R.

    2002-12-01

    In inertial fusion energy (IFE) power plant designs, the fuel is a spherical layer of frozen DT contained in a target that is injected at high velocity into the reaction chamber. For direct drive, typically laser beams converge at the centre of the chamber (CC) to compress and heat the target to fusion conditions. To obtain the maximum energy yield from the fusion reaction, the frozen DT layer must be at about 18.5 K and the target must maintain a high degree of spherical symmetry and surface smoothness when it reaches the CC. During its transit in the chamber the cryogenic target is heated by radiation from the hot chamber wall. The target is also heated by convection as it passes through the rarefied fill-gas used to control chamber wall damage by x-rays and debris from the target explosion. This article addresses the temperature limits at the target surface beyond which target uniformity may be damaged. It concentrates on direct drive targets because fuel warm up during injection is not currently thought to be an issue for present indirect drive designs and chamber concepts. Detailed results of parametric radiative and convective heating calculations are presented for direct-drive targets during injection into a dry-wall reaction chamber. The baseline approach to target survival utilizes highly reflective targets along with a substantially lower chamber wall temperature and fill-gas pressure than previously assumed. Recently developed high-Z material coatings with high heat reflectivity are discussed and characterized. The article also presents alternate target protection methods that could be developed if targets with inherent survival features cannot be obtained within a reasonable time span.

  12. Addressing the issues of target fabrication and injection for inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Goodin, D.T. E-mail: dan.goodin@gat.com; Nobile, A.; Hoffer, J.; Nikroo, A.; Besenbruch, G.E.; Brown, L.C.; Maxwell, J.L.; Meier, W.R.; Norimatsu, T.; Pulsifer, J.; Rickman, W.S.; Steckle, W.; Stephens, E.H.; Tillack, M

    2003-09-01

    Addressing the issues associated with target fabrication and injection is a major part of an international program to establish the feasibility of inertial fusion energy (IFE), both for laser-driven and heavy-ion driven concepts. A summary of the unique materials science and chemistry research programs associated with supplying targets for an IFE power plant is presented. The cost of manufacturing targets for commercial power applications is a significant perceived feasibility issue for IFE, and preliminary estimates of Target Fabrication Facility costs are discussed for both direct and indirect drive systems.

  13. ION BEAM HEATED TARGET SIMULATIONS FOR WARM DENSE MATTER PHYSICS AND INERTIAL FUSION ENERGY

    Energy Technology Data Exchange (ETDEWEB)

    Barnard, J.J.; Armijo, J.; Bailey, D.S.; Friedman, A.; Bieniosek, F.M.; Henestroza, E.; Kaganovich, I.; Leung, P.T.; Logan, B.G.; Marinak, M.M.; More, R.M.; Ng, S.F.; Penn, G.E.; Perkins, L.J.; Veitzer, S.; Wurtele, J.S.; Yu, S.S.; Zylstra, A.B.

    2008-08-01

    Hydrodynamic simulations have been carried out using the multi-physics radiation hydrodynamics code HYDRA and the simplified one-dimensional hydrodynamics code DISH. We simulate possible targets for a near-term experiment at LBNL (the Neutralized Drift Compression Experiment, NDCX) and possible later experiments on a proposed facility (NDCX-II) for studies of warm dense matter and inertial fusion energy related beam-target coupling. Simulations of various target materials (including solids and foams) are presented. Experimental configurations include single pulse planar metallic solid and foam foils. Concepts for double-pulsed and ramped-energy pulses on cryogenic targets and foams have been simulated for exploring direct drive beam target coupling, and concepts and simulations for collapsing cylindrical and spherical bubbles to enhance temperature and pressure for warm dense matter studies are described.

  14. Ion Beam Heated Target Simulations for Warm Dense Matter Physics and Inertial Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Barnard, J J; Armijo, J; Bailey, D S; Friedman, A; Bieniosek, F M; Henestroza, E; Kaganovich, I; Leung, P T; Logan, B G; Marinak, M M; More, R M; Ng, S F; Penn, G E; Perkins, L J; Veitzer, S; Wurtele, J S; Yu, S S; Zylstra, A B

    2008-08-12

    Hydrodynamic simulations have been carried out using the multi-physics radiation hydrodynamics code HYDRA and the simplified one-dimensional hydrodynamics code DISH. We simulate possible targets for a near-term experiment at LBNL (the Neutralized Drift Compression Experiment, NDCX) and possible later experiments on a proposed facility (NDCX-II) for studies of warm dense matter and inertial fusion energy related beam-target coupling. Simulations of various target materials (including solids and foams) are presented. Experimental configurations include single pulse planar metallic solid and foam foils. Concepts for double-pulsed and ramped-energy pulses on cryogenic targets and foams have been simulated for exploring direct drive beam target coupling, and concepts and simulations for collapsing cylindrical and spherical bubbles to enhance temperature and pressure for warm dense matter studies are described.

  15. Development of position measurement unit for flying inertial fusion energy target

    Science.gov (United States)

    Tsuji, R.; Endo, T.; Yoshida, H.; Norimatsu, T.

    2016-03-01

    We have reported the present status in the development of a position measurement unit (PMU) for a flying inertial fusion energy (IFE) target. The PMU, which uses Arago spot phenomena, is designed to have a measurement accuracy smaller than 1 μm. By employing divergent, pulsed orthogonal laser beam illumination, we can measure the time and the target position at the pulsed illumination. The two-dimensional Arago spot image is compressed into one-dimensional image by a cylindrical lens for real-time processing. The PMU are set along the injection path of the flying target. The local positions of the target in each PMU are transferred to the controller and analysed to calculate the target trajectory. Two methods are presented to calculate the arrival time and the arrival position of the target at the reactor centre.

  16. Safety and environmental advantages of using tritium-lean targets for inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J.F.; Logan, B.G.; Perkins, L.J.; Meier, W.R.; Moir, R.W. [Lawrence Livermore National Lab., CA (United States); Atzeni, S. [Associazione EURATOM-ENEA sulla Fusione, Frascati (Italy); Sanz, J. [Escuela Tecnica Superior de Ingenieros Industriales, Universidad Nacional de Educacion a Distancia and Instituto de Fusion Nuclear, Dept. Ingenieria Energetica, Bilbao (Spain)

    2000-07-01

    While traditional inertial fusion energy target designs typically use equimolar portions of deuterium and tritium and have areal densities ({rho}r) of {approx} 3 g/cm{sup 2}, significant safety and environmental (S and E) advantages may be obtained through the use of high-density ({rho}r {approx} 10 g/cm{sup 2}) targets with tritium components as low as 0.5%. Such targets would absorb much of the neutron energy within the target and could be self-sufficient from a tritium breeding point of view. Tritium self-sufficiency within the target would free target chamber designers from the need to use lithium-bearing blanket materials, while low inventories within each target would translate into low inventories in target fabrication facilities. Absorption of much of the neutron energy within the target, the extremely low tritium inventories, and the greatly moderated neutron spectrum, make 'tritium-lean' targets appear quite attractive from an S and E perspective. (authors)

  17. Simulation of Intense Beams and Targets for Heavy-Ion-Fusion Science (HEDLP / Inertial Fusion Energy)

    Energy Technology Data Exchange (ETDEWEB)

    Friedman, Alex [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barnard, John J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cohen, Ron H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Dorf, Mikhail [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Eder, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Grote, Dave P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lund, Steve M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sharp, William M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Henestroza, Enrique [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lee, Ed P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Vay, Jean -Luc [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Davidson, Ron C. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Kaganovich, Igor D. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Qin, Hong [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Startsev, Ed [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Fagnan, Kirsten [National Energy Research Scientific Computing Center, Berkeley, CA (United States); Koniges, Alice [National Energy Research Scientific Computing Center, Berkeley, CA (United States); Bertozzi, Andrea [Univ. of California, Los Angeles, CA (United States)

    2010-08-26

    Our principal goals, and activities in support of those goals, over the next five years are as follows: (1) Optimize the properties of the NDCX-II beam for each class of target experiments; achieve quantitative agreement with measurements; develop improved machine configurations and operating points. To accomplish these goals, we plan to use Warp to simulate NDCX-II from source to target, in full kinetic detail, including first-principles modeling of beam neutralization by plasma. The output from an ensemble of Warp runs (representing shot-to-shot variations) will be used as input to target simulations using ALE-AMR on NERSC, and other codes. (2) Develop enhanced versions of NDCX-II (the machine is designed to be extensible and reconfigurable), and carry out studies to define a next-step ion beam facility. To accomplish these goals, much of the work will involve iterative optimization employing Warp runs that assume ideal beam neutralization downstream of the accelerator. (3) Carry out detailed target simulations in the Warm Dense Matter regime using the ALE-AMR code, including surface tension effects, liquid-vapor coexistence, and accurate models of both the driving beam and the target geometry. For this we will need to make multiple runs (to capture shot-to-shot variations), and to both develop and employ synthetic diagnostics (to enable comparison with experiments). The new science that will be revealed is the physics of the transition from the liquid to vapor state of a volumetrically superheated material, wherein droplets are formed, and wherein phase transitions, surface tension and hydrodynamics all play significant roles in the dynamics. These simulations will enable calculations of equation of state and other material properties, and will also be of interest for their illumination of the science of droplet formation.

  18. Developing target injection and tracking for inertial fusion energy power plants

    Science.gov (United States)

    Goodin, D. T.; Alexander, N. B.; Gibson, C. R.; Nobile, A.; Petzoldt, R. W.; Siegel, N. P.; Thompson, L.

    2001-05-01

    Fuelling of a commercial inertial fusion energy (IFE) power plant consists of supplying about 500 000 fusion targets each day. The most challenging type of target in this regard is that for laser driven direct drive IFE power plants. Spherical capsules with cryogenic DT fuel must be injected into the centre of a reaction chamber operating at temperatures as high as 1500° C and possibly containing as much as 0.5 torr of xenon fill gas. The DT layer must remain highly symmetric, have a smooth inner ice surface finish and reach the chamber centre (CC) at a temperature of about 18.5 K. This target must be positioned at the centre of the chamber with a placement accuracy of +/-5 mm. The accuracy of alignment of the laser driver beams and the target in its final position must be within +/-20 μm. All this must be repeated six times per second. The method proposed to meet these requirements is to inject the targets into the reaction chamber at high speed ( approx 400 m/s), track them, and hit them in flight with steerable driver beams. The challenging scientific and technological issues associated with this task are being addressed through a combination of analyses, modelling, materials property measurements and demonstration tests with representative injection equipment. Measurements of relevant DT properties are planned at Los Alamos National Laboratory. An experimental target injection and tracking system is now being designed to support the development of survivable targets and demonstrate successful injection scenarios. Analyses of target heating are under way. Calculations have shown that a direct drive target must have a highly reflective outer surface to prevent excess heating by thermal radiation. In addition, heating by hot chamber fill gas during injection far outweighs that by the thermal radiation. It is concluded that the dry wall, gas filled reaction chambers must have gas pressures and wall temperatures less than previously assumed in order to prevent

  19. Inertial fusion energy; L'energie de fusion inertielle

    Energy Technology Data Exchange (ETDEWEB)

    Decroisette, M.; Andre, M.; Bayer, C.; Juraszek, D. [CEA Bruyeres-le-Chatel, Dir. des Systemes d' Information (CEA/DIF), 91 (France); Le Garrec, B. [CEA Centre d' Etudes Scientifiques et Techniques d' Aquitaine, 33 - Le Barp (France); Deutsch, C. [Paris-11 Univ., 91 - Orsay (France); Migus, A. [Institut d' Optique Centre scientifique, 91 - Orsay (France)

    2005-07-01

    We first recall the scientific basis of inertial fusion and then describe a generic fusion reactor with the different components: the driver, the fusion chamber, the material treatment unit, the target factory and the turbines. We analyse the options proposed at the present time for the driver and for target irradiation scheme giving the state of art for each approach. We conclude by the presentation of LMJ (laser Megajoule) and NIF (national ignition facility) projects. These facilities aim to demonstrate the feasibility of laboratory DT ignition, first step toward Inertial Fusion Energy. (authors)

  20. Large Scale Computing and Storage Requirements for Fusion Energy Sciences: Target 2017

    Energy Technology Data Exchange (ETDEWEB)

    Gerber, Richard

    2014-05-02

    The National Energy Research Scientific Computing Center (NERSC) is the primary computing center for the DOE Office of Science, serving approximately 4,500 users working on some 650 projects that involve nearly 600 codes in a wide variety of scientific disciplines. In March 2013, NERSC, DOE?s Office of Advanced Scientific Computing Research (ASCR) and DOE?s Office of Fusion Energy Sciences (FES) held a review to characterize High Performance Computing (HPC) and storage requirements for FES research through 2017. This report is the result.

  1. MULTI-IFE-A one-dimensional computer code for Inertial Fusion Energy (IFE) target simulations

    Science.gov (United States)

    Ramis, R.; Meyer-ter-Vehn, J.

    2016-06-01

    The code MULTI-IFE is a numerical tool devoted to the study of Inertial Fusion Energy (IFE) microcapsules. It includes the relevant physics for the implosion and thermonuclear ignition and burning: hydrodynamics of two component plasmas (ions and electrons), three-dimensional laser light ray-tracing, thermal diffusion, multigroup radiation transport, deuterium-tritium burning, and alpha particle diffusion. The corresponding differential equations are discretized in spherical one-dimensional Lagrangian coordinates. Two typical application examples, a high gain laser driven capsule and a low gain radiation driven marginally igniting capsule are discussed. In addition to phenomena relevant for IFE, the code includes also components (planar and cylindrical geometries, transport coefficients at low temperature, explicit treatment of Maxwell's equations) that extend its range of applicability to laser-matter interaction at moderate intensities (<1016 W cm-2). The source code design has been kept simple and structured with the aim to encourage user's modifications for specialized purposes.

  2. Perspectives on Magnetized Target Fusion Power Plants

    Science.gov (United States)

    Miller, R. L.

    2007-06-01

    One approach to Magnetized Target Fusion (MTF) builds upon the ongoing experimental effort (FRX-L) to generate a Field Reversed Configuration (FRC) target plasma suitable for translation and cylindrical-liner (i.e., converging flux conserver) implosion. Numerical modeling is underway to elucidate key performance drivers for possible future power-plant extrapolations. The fusion gain, Q (ratio of DT fusion yield to the sum of initial liner kinetic energy plus plasma formation energy), sets the power-plant duty cycle for a nominal design electric power [ e.g. 1,000 MWe(net)]. A pulsed MTF power plant of this type derives from the historic Fast Liner Reactor (FLR) concept and shares attributes with the recent Inertial Fusion Energy (IFE) Z-pinch and laser-driven pellet HYLIFE-II conceptual designs.

  3. FY2014 FES (Fusion Energy Sciences) Theory & Simulation Performance Target, Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Guoyong [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Budny, Robert [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Gorelenkov, Nikolai [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Poli, Francesca [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Chen, Yang [Univ. of Colorado, Boulder, CO (United States); McClenaghan, Joseph [Univ. of California, Irvine, CA (United States); Lin, Zhihong [Univ. of California, Irvine, CA (United States); Spong, Don [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bass, Eric [Univ. of California, San Diego, CA (United States); Waltz, Ron [General Atomics, San Diego, CA (United States)

    2014-10-14

    We report here the work done for the FY14 OFES Theory Performance Target as given below: "Understanding alpha particle confinement in ITER, the world's first burning plasma experiment, is a key priority for the fusion program. In FY 2014, determine linear instability trends and thresholds of energetic particle-driven shear Alfven eigenmodes in ITER for a range of parameters and profiles using a set of complementary simulation models (gyrokinetic, hybrid, and gyrofluid). Carry out initial nonlinear simulations to assess the effects of the unstable modes on energetic particle transport". In the past year (FY14), a systematic study of the alpha-driven Alfven modes in ITER has been carried out jointly by researchers from six institutions involving seven codes including the transport simulation code TRANSP (R. Budny and F. Poli, PPPL), three gyrokinetic codes: GEM (Y. Chen, Univ. of Colorado), GTC (J. McClenaghan, Z. Lin, UCI), and GYRO (E. Bass, R. Waltz, UCSD/GA), the hybrid code M3D-K (G.Y. Fu, PPPL), the gyro-fluid code TAEFL (D. Spong, ORNL), and the linear kinetic stability code NOVA-K (N. Gorelenkov, PPPL). A range of ITER parameters and profiles are specified by TRANSP simulation of a hybrid scenario case and a steady-state scenario case. Based on the specified ITER equilibria linear stability calculations are done to determine the stability boundary of alpha-driven high-n TAEs using the five initial value codes (GEM, GTC, GYRO, M3D-K, and TAEFL) and the kinetic stability code (NOVA-K). Both the effects of alpha particles and beam ions have been considered. Finally, the effects of the unstable modes on energetic particle transport have been explored using GEM and M3D-K.

  4. FY2014 FES (Fusion Energy Sciences) Theory & Simulation Performance Target, Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Guoyong [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Budny, Robert [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Gorelenkov, Nikolai [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Poli, Francesca [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Chen, Yang [Univ. of Colorado, Boulder, CO (United States); McClenaghan, Joseph [Univ. of California, Irvine, CA (United States); Lin, Zhihong [Univ. of California, Irvine, CA (United States); Spong, Don [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bass, Eric [Univ. of California, San Diego, CA (United States); Waltz, Ron [General Atomics, San Diego, CA (United States)

    2014-10-14

    We report here the work done for the FY14 OFES Theory Performance Target as given below: "Understanding alpha particle confinement in ITER, the world's first burning plasma experiment, is a key priority for the fusion program. In FY 2014, determine linear instability trends and thresholds of energetic particle-driven shear Alfven eigenmodes in ITER for a range of parameters and profiles using a set of complementary simulation models (gyrokinetic, hybrid, and gyrofluid). Carry out initial nonlinear simulations to assess the effects of the unstable modes on energetic particle transport". In the past year (FY14), a systematic study of the alpha-driven Alfven modes in ITER has been carried out jointly by researchers from six institutions involving seven codes including the transport simulation code TRANSP (r. Budny and F. Poli, PPPL), three gyrokinetic codes: GEM (Y. Chen, Univ. of Colorado), GTC (J. McClenaghan, Z. Lin, UCI), and GYRO (E. Bass, R. Waltz, UCSD/GA), the hybrid code M3D-K (G.Y. Fu, PPPL), the gyro-fluid code TAEFL (D. Spong, ORNL), and the linear kinetic stability code NOVA-K (N. Gorelenkov, PPPL). A range of ITER parameters and profiles are specified by TRANSP simulation of a hybrid scenario case and a steady state scenario case. Based on the specified ITER equilibria linear stability calculations are done to determine the stability boundary of alpha-driven high-n TAEs using the five initial value codes (GEM, GTC, GYRO, M3D-K, and TAEFL) and the kinetic stability code (NOVA-K). Both the effects of alpha particles and beam ions have been considered. Finally the effects of the unstable modes on energetic particle transport have been explored using GEM and M3D-K.

  5. Electron energy deposition to the fusion target core for fast ignition

    Energy Technology Data Exchange (ETDEWEB)

    Wang, W M; Sheng, Z M; Li, Y T; Hao, B; Zhang, J [Beijing National Laboratory of Condensed Matter Physics, Institute of Physics, CAS, Beijing 100190 (China); Norreys, P A; Sherlock, M; Trines, R; Robinson, A P L, E-mail: hbwwml@aphy.iphy.ac.e, E-mail: tzmsheng@sjtu.edu.c [Central Laser Facility, CCLRC Rutherford Appleton Laboratory, Chilton, Didcot, Oxfordshire, OX11 0QX (United Kingdom)

    2010-08-01

    Heating of the target core for fast ignition by electron beams is investigated by two-dimensional collisional particle-in-cell simulations. It is found that the electron beams emitted from the core surface with the initial energy of 1.4MeV, 2.4MeV, and 4.2MeV can heat most efficiently the core with {rho}r = 0.75g/cm{sup 2}, 1.5g/cm{sup 2}, and 3g/cm{sup 2}, respectively, when taking {rho} = 300g/cm{sup 3}, where {rho} and r are the mass density and radius of the core, respectively.

  6. The Science and Technologies for Fusion Energy With Lasers and Direct-Drive Targets

    Science.gov (United States)

    2010-04-01

    international efforts. Note that the National Ignition Fa- cility ( NIF ) will use the indirect-drive approach for the first laboratory demonstration of...thermonuclear ignition. This approach, where laser light is converted to X-rays that drive the target, was chosen based on the primary mission of the NIF to...pumped with an array of high-efficiency (> 60%) high-power (> 100-W) diodes. The medium is Yb:S-FAP, but other media, including the NIF choice of Nd:glass

  7. Realizing Technologies for Magnetized Target Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Wurden, Glen A. [Los Alamos National Laboratory

    2012-08-24

    Researchers are making progress with a range of magneto-inertial fusion (MIF) concepts. All of these approaches use the addition of a magnetic field to a target plasma, and then compress the plasma to fusion conditions. The beauty of MIF is that driver power requirements are reduced, compared to classical inertial fusion approaches, and simultaneously the compression timescales can be longer, and required implosion velocities are slower. The presence of a sufficiently large Bfield expands the accessibility to ignition, even at lower values of the density-radius product, and can confine fusion alphas. A key constraint is that the lifetime of the MIF target plasma has to be matched to the timescale of the driver technology (whether liners, heavy ions, or lasers). To achieve sufficient burn-up fraction, scaling suggests that larger yields are more effective. To handle the larger yields (GJ level), thick liquid wall chambers are certainly desired (no plasma/neutron damage materials problem) and probably required. With larger yields, slower repetition rates ({approx}0.1-1 Hz) for this intrinsically pulsed approach to fusion are possible, which means that chamber clearing between pulses can be accomplished on timescales that are compatible with simple clearing techniques (flowing liquid droplet curtains). However, demonstration of the required reliable delivery of hundreds of MJ of energy, for millions of pulses per year, is an ongoing pulsed power technical challenge.

  8. Magnetized Target Fusion Collaboration. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Slough, John

    2012-04-18

    Nuclear fusion has the potential to satisfy the prodigious power that the world will demand in the future, but it has yet to be harnessed as a practical energy source. The entry of fusion as a viable, competitive source of power has been stymied by the challenge of finding an economical way to provide for the confinement and heating of the plasma fuel. It is the contention here that a simpler path to fusion can be achieved by creating fusion conditions in a different regime at small scale (~ a few cm). One such program now under study, referred to as Magnetized Target Fusion (MTF), is directed at obtaining fusion in this high energy density regime by rapidly compressing a compact toroidal plasmoid commonly referred to as a Field Reversed Configuration (FRC). To make fusion practical at this smaller scale, an efficient method for compressing the FRC to fusion gain conditions is required. In one variant of MTF a conducting metal shell is imploded electrically. This radially compresses and heats the FRC plasmoid to fusion conditions. The closed magnetic field in the target plasmoid suppresses the thermal transport to the confining shell, thus lowering the imploding power needed to compress the target. The undertaking described in this report was to provide a suitable target FRC, as well as a simple and robust method for inserting and stopping the FRC within the imploding liner. The FRC must also survive during the time it takes for the metal liner to compress the FRC target. The initial work at the UW was focused on developing adequate preionization and flux trapping that were found to be essential in past experiments for obtaining the density, flux and most critically, FRC lifetime required for MTF. The timescale for testing and development of such a source can be rapidly accelerated by taking advantage of a new facility funded by the Department of Energy. At this facility, two inductive plasma accelerators (IPA) were constructed and tested. Recent experiments with

  9. Acoustically Driven Magnetized Target Fusion At General Fusion: An Overview

    Science.gov (United States)

    O'Shea, Peter; Laberge, M.; Donaldson, M.; Delage, M.; the Fusion Team, General

    2016-10-01

    Magnetized Target Fusion (MTF) involves compressing an initial magnetically confined plasma of about 1e23 m-3, 100eV, 7 Tesla, 20 cm radius, >100 μsec life with a 1000x volume compression in 100 microseconds. If near adiabatic compression is achieved, the final plasma of 1e26 m-3, 10keV, 700 Tesla, 2 cm radius, confined for 10 μsec would produce interesting fusion energy gain. General Fusion (GF) is developing an acoustic compression system using pneumatic pistons focusing a shock wave on the CT plasma in the center of a 3 m diameter sphere filled with liquid lead-lithium. Low cost driver, straightforward heat extraction, good tritium breeding ratio and excellent neutron protection could lead to a practical power plant. GF (65 employees) has an active plasma R&D program including both full scale and reduced scale plasma experiments and simulation of both. Although acoustic driven compression of full scale plasmas is the end goal, present compression studies use reduced scale plasmas and chemically accelerated Aluminum liners. We will review results from our plasma target development, motivate and review the results of dynamic compression field tests and briefly describe the work to date on the acoustic driver front.

  10. Magnetized Target Fusion (MTF): Principles, Status, and International Collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Kirkpatrick, R.C.

    1998-11-16

    Magnetized target fusion (MTF) is an approach to thermonuclear fusion that is intermediate between the two extremes of inertial and magnetic confinement. Target plasma preparation is followed by compression to fusion conditions. The use of a magnetic field to reduce electron thermal conduction and potentially enhance DT alpha energy deposition allows the compression rate to be drastically reduced relative to that for inertial confinement fusion. This leads to compact systems with target driver power and intensity requirements that are orders of magnitude lower than for ICF. A liner on plasma experiment has been proposed to provide a firm proof of principle for MTF.

  11. (Fusion energy research)

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, C.A. (ed.)

    1988-01-01

    This report discusses the following topics: principal parameters achieved in experimental devices (FY88); tokamak fusion test reactor; Princeton beta Experiment-Modification; S-1 Spheromak; current drive experiment; x-ray laser studies; spacecraft glow experiment; plasma deposition and etching of thin films; theoretical plasma; tokamak modeling; compact ignition tokamak; international thermonuclear experimental reactor; Engineering Department; Project Planning and Safety Office; quality assurance and reliability; and technology transfer.

  12. Direct conversion of fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, Markus

    2003-03-01

    Deuterium and tritium are expected to be used as fuel in the first fusion reactors. Energy is released as kinetic energy of ions and neutrons, when deuterium reacts with tritium. One way to convert the kinetic energy to electrical energy, is to let the ions and neutrons hit the reactor wall and convert the heat that is caused by the particle bombardment to electrical energy with ordinary thermal conversion. If the kinetic energy of the ions instead is converted directly to electrical energy, a higher efficiency of the energy conversion is possible. The majority of the fusion energy is released as kinetic energy of neutrons, when deuterium reacts with tritium. Fusion reactions such as the D-D reactions, the D-{sup 3}He reaction and the p-{sup 11}B reaction, where a larger part of the fusion energy becomes kinetic energy of charged particles, appears therefore more suitable for direct conversion. Since they have lower reactivity than the D-T reaction, they need a larger {beta}B{sup 2}{sub 0} to give sufficiently high fusion power density. Because of this, the fusion configurations spherical torus (ST) and field-reversed configuration (FRC), where high {beta} values are possible, appear interesting. Rosenbluth and Hinton come to the conclusion that efficient direct conversion isn't possible in closed field line systems and that open geometries, which facilitate direct conversion, provide inadequate confinement for D-{sup 3}He. It is confirmed in this study that it doesn't seem possible to achieve as high direct conversion efficiency in closed systems as in open systems. ST and FRC fusion power plants that utilize direct conversion seem however interesting. Calculations with the help of Maple indicate that the reactor parameters needed for a D-D ST and a D{sub 3} He ST hopefully are possible to achieve. The best energy conversion option for a D-D or D{sub 3} He ST appears to be direct electrodynamic conversion (DEC) together with ordinary thermal conversion

  13. Chamber Design for the Laser Inertial Fusion Energy (LIFE) Engine

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J F; Abbott, R P; Aceves, S; Anklam, T; Badders, D; Cook, A W; DeMuth, J; Divol, L; El-Dasher, B; Farmer, J C; Flowers, D; Fratoni, M; ONeil, R G; Heltemes, T; Kane, J; Kramer, K J; Kramer, R; Lafuente, A; Loosmore, G A; Morris, K R; Moses, G A; Olson, B; Pantano, C; Reyes, S; Rhodes, M; Roe, K; Sawicki, R; Scott, H; Spaeth, M; Tabak, M; Wilks, S

    2010-11-30

    The Laser Inertial Fusion Energy (LIFE) concept is being designed to operate as either a pure fusion or hybrid fusion-fission system. The present work focuses on the pure fusion option. A key component of a LIFE engine is the fusion chamber subsystem. It must absorb the fusion energy, produce fusion fuel to replace that burned in previous targets, and enable both target and laser beam transport to the ignition point. The chamber system also must mitigate target emissions, including ions, x-rays and neutrons and reset itself to enable operation at 10-15 Hz. Finally, the chamber must offer a high level of availability, which implies both a reasonable lifetime and the ability to rapidly replace damaged components. An integrated design that meets all of these requirements is described herein.

  14. Review of the Inertial Fusion Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2004-03-29

    Igniting fusion fuel in the laboratory remains an alluring goal for two reasons: the desire to study matter under the extreme conditions needed for fusion burn, and the potential of harnessing the energy released as an attractive energy source for mankind. The inertial confinement approach to fusion involves rapidly compressing a tiny spherical capsule of fuel, initially a few millimeters in radius, to densities and temperatures higher than those in the core of the sun. The ignited plasma is confined solely by its own inertia long enough for a significant fraction of the fuel to burn before the plasma expands, cools down and the fusion reactions are quenched. The potential of this confinement approach as an attractive energy source is being studied in the Inertial Fusion Energy (IFE) program, which is the subject of this report. A complex set of interrelated requirements for IFE has motivated the study of novel potential solutions. Three types of “drivers” for fuel compression are presently studied: high-averagepower lasers (HAPL), heavy-ion (HI) accelerators, and Z-Pinches. The three main approaches to IFE are based on these drivers, along with the specific type of target (which contains the fuel capsule) and chamber that appear most promising for a particular driver.

  15. Mass Producing Targets for Nuclear Fusion

    Science.gov (United States)

    Wang, T. G.; Elleman, D. D.; Kendall, J. M.

    1983-01-01

    Metal-encapsulating technique advances prospects of controlling nuclear fusion. Prefilled fusion targets form at nozzle as molten metal such as tin flows through outer channel and pressurized deuterium/tritium gas flows through inner channel. Molten metal completely encloses gas charge as it drops off nozzle.

  16. Fusion Energy for Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Fillo, J. A.; Powell, J. R.; Steinberg, M.; Salzano, F.; Benenati, R.; Dang, V.; Fogelson, S.; Isaacs, H.; Kouts, H.; Kushner, M.; Lazareth, O.; Majeski, S.; Makowitz, H.; Sheehan, T. V.

    1978-09-01

    The decreasing availability of fossil fuels emphasizes the need to develop systems which will produce synthetic fuel to substitute for and supplement the natural supply. An important first step in the synthesis of liquid and gaseous fuels is the production of hydrogen. Thermonuclear fusion offers an inexhaustible source of energy for the production of hydrogen from water. Depending on design, electric generation efficiencies of approximately 40 to 60% and hydrogen production efficiencies by high temperature electrolysis of approximately 50 to 70% are projected for fusion reactors using high temperature blankets.

  17. Fusion technologies for Laser Inertial Fusion Energy (LIFE∗

    Directory of Open Access Journals (Sweden)

    Kramer K.J.

    2013-11-01

    Full Text Available The Laser Inertial Fusion-based Energy (LIFE engine design builds upon on going progress at the National Ignition Facility (NIF and offers a near-term pathway to commercial fusion. Fusion technologies that are critical to success are reflected in the design of the first wall, blanket and tritium separation subsystems. The present work describes the LIFE engine-related components and technologies. LIFE utilizes a thermally robust indirect-drive target and a chamber fill gas. Coolant selection and a large chamber solid-angle coverage provide ample tritium breeding margin and high blanket gain. Target material selection eliminates the need for aggressive chamber clearing, while enabling recycling. Demonstrated tritium separation and storage technologies limit the site tritium inventory to attractive levels. These key technologies, along with the maintenance and advanced materials qualification program have been integrated into the LIFE delivery plan. This describes the development of components and subsystems, through prototyping and integration into a First Of A Kind power plant.

  18. Ion-driver fast ignition: Reducing heavy-ion fusion driver energy and cost, simplifying chamber design, target fab, tritium fueling and power conversion

    Energy Technology Data Exchange (ETDEWEB)

    Logan, G.; Callahan-Miller, D.; Perkins, J.; Caporaso, G.; Tabak, M.; Moir, R.; Meier, W.; Bangerter, Roger; Lee, Ed

    1998-04-01

    Ion fast ignition, like laser fast ignition, can potentially reduce driver energy for high target gain by an order of magnitude, while reducing fuel capsule implosion velocity, convergence ratio, and required precisions in target fabrication and illumination symmetry, all of which should further improve and simplify IFE power plants. From fast-ignition target requirements, we determine requirements for ion beam acceleration, pulse-compression, and final focus for advanced accelerators that must be developed for much shorter pulses and higher voltage gradients than today's accelerators, to deliver the petawatt peak powers and small focal spots ({approx}100 {micro}m) required. Although such peak powers and small focal spots are available today with lasers, development of such advanced accelerators is motivated by the greater likely efficiency of deep ion penetration and deposition into pre-compressed 1000x liquid density DT cores. Ion ignitor beam parameters for acceleration, pulse compression, and final focus are estimated for two examples based on a Dielectric Wall Accelerator; (1) a small target with {rho}r {approx} 2 g/cm{sup 2} for a small demo/pilot plant producing {approx}40 MJ of fusion yield per target, and (2) a large target with {rho}r {approx} 10 g/cm{sup 2} producing {approx}1 GJ yield for multi-unit electricity/hydrogen plants, allowing internal T-breeding with low T/D ratios, >75 % of the total fusion yield captured for plasma direct conversion, and simple liquid-protected chambers with gravity clearing. Key enabling development needs for ion fast ignition are found to be (1) ''Close-coupled'' target designs for single-ended illumination of both compressor and ignitor beams; (2) Development of high gradient (>25 MV/m) linacs with high charge-state (q {approx} 26) ion sources for short ({approx}5 ns) accelerator output pulses; (3) Small mm-scale laser-driven plasma lens of {approx}10 MG fields to provide steep focusing angles

  19. Fuel Target Implosion in Ion beam Inertial Confinement Fusion

    CERN Document Server

    Kawata, Shigeo

    2015-01-01

    The numerical results for the fuel target implosion are presented in order to clarify the target physics in ion beam inertial fusion. The numerical analyses are performed for a direct-driven ion beam target. In the paper the following issues are studied: the beam obliquely incidence on the target surface, the plasma effect on the beam-stopping power, the beam particle energy, the beam time duration, the target radius, the beam input energy and the non-uniformity effect on the fuel target performance. In this paper the beam ions are protons.

  20. Flight and Stability of a Laser Inertial Fusion Energy Target in the Drift Region between Injection and the Reaction Chamber with Computational Fluid Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Mitori, T. [California Polytechnic State Univ. (CalPoly), San Luis Obispo, CA (United States)

    2013-12-01

    A Laser Inertial Fusion Energy (LIFE) target’s flight through a low Reynolds number and high Mach number regime was analyzed with computational fluid dynamics software. This regime consisted of xenon gas at 1,050 K and approximately 6,670 Pa. Simulations with similar flow conditions were performed with a sphere and compared with experimental data and published correlations for validation purposes. Transient considerations of the developing flow around the target were explored. Simulations of the target at different velocities were used to determine correlations for the drag coefficient and Nusselt number as functions of the Reynolds number. Simulations with different angles of attack were used to determine the aerodynamic coefficients of drag, lift, Magnus moment, and overturning moment as well as target stability. The drag force, lift force, and overturning moment changed minimally with spin. Above an angle of attack of 15°, the overturning moment would be destabilizing. At low angles of attack (less than 15°), the overturning moment would tend to decrease the target’s angle of attack, indicating the lack of a need for spin for stability at small angles. This stabilizing moment would cause the target to move in a mildly damped oscillation about the axis parallel to the free-stream velocity vector through the target’s center of gravity.

  1. Physics of laser fusion. Vol. I. Theory of the coronal plasma in laser-fusion targets

    Energy Technology Data Exchange (ETDEWEB)

    Max, C.E.

    1981-12-01

    This monograph deals with the physics of the coronal region in laser fusion targets. The corona consists of hot plasma which has been evaporated from the initially solid target during laser heating. It is in the corona that the laser light is absorbed by the target, and the resulting thermal energy is conducted toward cold high-density regions, where ablation occurs. The topics to be discussed are theoretical mechanisms for laser light absorption and reflection, hot-electron production, and the physics of heat conduction in laser-produced plasmas. An accompanying monograph by H. Ahlstrom (Vol.II) reviews the facilities, diagnostics, and data from recent laser fusion experiments.

  2. Reactor potential for magnetized target fusion

    Energy Technology Data Exchange (ETDEWEB)

    Dahlin, J.E

    2001-06-01

    Magnetized Target Fusion (MTF) is a possible pathway to thermonuclear fusion different from both magnetic fusion and inertial confinement fusion. An imploding cylindrical metal liner compresses a preheated and magnetized plasma configuration until thermonuclear conditions are achieved. In this report the Magnetized Target Fusion concept is evaluated and a zero-dimensional computer model of the plasma, liner and circuit as a connected system is designed. The results of running this code are that thermonuclear conditions are achieved indeed, but only during a very short time. At peak compression the pressure from the compressed plasma and magnetic field is so large reversing the liner implosion into an explosion. The time period of liner motion reversal is termed the dwell time and is crucial to the performance of the fusion system. Parameters as liner thickness and plasma density are certainly of significant importance to the dwell time, but it seems like a reactor based on the MTF principle hardly can become economic if not innovative solutions are introduced. In the report two such solutions are presented as well.

  3. Z-Pinch Fusion for Energy Applications

    Energy Technology Data Exchange (ETDEWEB)

    SPIELMAN,RICK B.

    2000-01-01

    Z pinches, the oldest fusion concept, have recently been revisited in light of significant advances in the fields of plasma physics and pulsed power engineering. The possibility exists for z-pinch fusion to play a role in commercial energy applications. We report on work to develop z-pinch fusion concepts, the result of an extensive literature search, and the output for a congressionally-mandated workshop on fusion energy held in Snowmass, Co July 11-23,1999.

  4. Fusion Energy Sciences Network Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Dart, Eli [ESNet, Berkeley, CA (United States); Tierney, Brian [ESNet, Berkeley, CA (United States)

    2012-09-26

    The Energy Sciences Network (ESnet) is the primary provider of network connectivity for the U.S. Department of Energy Office of Science, the single largest supporter of basic research in the physical sciences in the United States. In support of the Office of Science programs, ESnet regularly updates and refreshes its understanding of the networking requirements of the instruments, facilities, scientists, and science programs that it serves. This focus has helped ESnet to be a highly successful enabler of scientific discovery for over 25 years. In December 2011, ESnet and the Office of Fusion Energy Sciences (FES), of the DOE Office of Science (SC), organized a workshop to characterize the networking requirements of the programs funded by FES. The requirements identified at the workshop are summarized in the Findings section, and are described in more detail in the body of the report.

  5. Uniformity of fuel target implosion in Heavy Ion Fusion

    CERN Document Server

    Kawata, S; Suzuki, T; Karino, T; Barada, D; Ogoyski, A I; Ma, Y Y

    2015-01-01

    In inertial confinement fusion the target implosion non-uniformity is introduced by a driver beams' illumination non-uniformity, a fuel target alignment error in a fusion reactor, the target fabrication defect, et al. For a steady operation of a fusion power plant the target implosion should be robust against the implosion non-uniformities. In this paper the requirement for the implosion uniformity is first discussed. The implosion uniformity should be less than a few percent. A study on the fuel hotspot dynamics is also presented and shows that the stagnating plasma fluid provides a significant enhancement of vorticity at the final stage of the fuel stagnation. Then non-uniformity mitigation mechanisms of the heavy ion beam (HIB) illumination are also briefly discussed in heavy ion inertial fusion (HIF). A density valley appears in the energy absorber, and the large-scale density valley also works as a radiation energy confinement layer, which contributes to a radiation energy smoothing. In HIF a wobbling he...

  6. Fusion energy and nuclear non-proliferation

    Energy Technology Data Exchange (ETDEWEB)

    Goldston, Rob [Princeton Plasma Physics Lab, Princeton (United States)

    2014-07-01

    Neutrons from DT fusion can be used to produce {sup 239}Pu or {sup 233}U. However since no fertile nor fissile material need be present in a pure fusion power plant, it would be relatively easy to detect significant covert transmutation in a declared facility. Clandestine fusion-based transmutation does not appear credible. Furthermore, no fissile materials are immediately available in a fusion breakout scenario. DT fusion systems produce and burn 400g of tritium per day, a small fraction of which, if diverted, could be used to enhance the efficiency, reliability and/or safety of a nuclear weapon. Very accurate T accountancy needs to be developed for fusion energy systems. Finally, the spread of inertial fusion energy R and D may result in dissemination of knowledge relevant to the design of nuclear weapons. International agreements to restrain information transfer are required. In summary, fusion is much safer from a proliferation standpoint than fission, but still requires verification and control.

  7. Scientific and technological advancements in inertial fusion energy

    Science.gov (United States)

    Hinkel, D. E.

    2013-10-01

    Scientific advancements in inertial fusion energy (IFE) were reported on at the IAEA Fusion Energy Conference, October 2012. Results presented transect the different ways to assemble the fuel, different scenarios for igniting the fuel, and progress in IFE technologies. The achievements of the National Ignition Campaign within the USA, using the National Ignition Facility (NIF) to indirectly drive laser fusion, have found beneficial the achievements in other IFE arenas such as directly driven laser fusion and target fabrication. Moreover, the successes at NIF have pay-off to alternative scenarios such as fast ignition, shock ignition, and heavy-ion fusion as well as to directly driven laser fusion. This synergy is summarized here, and future scientific studies are detailed.

  8. Fusion - An energy source for synthetic fuels

    Science.gov (United States)

    Fillo, J. A.; Powell, J.; Steinberg, M.

    1980-05-01

    An important first step in the synthesis of liquid and gaseous fuels is the production of hydrogen. Thermonuclear fusion offers an inexhaustible source of energy for the production of hydrogen from water. Depending on design, electric generation efficiencies of 40 to 60% and hydrogen production efficiencies by high temperature electrolysis of 50 to 70% are projected for fusion reactors using high temperature blankets. Fusion/coal symbiotic systems appear economically promising for the first generation of commercial fusion synfuels plants. In the long term, there could be a gradual transition to an inexhaustible energy system based solely on fusion.

  9. Fusion as a future energy source

    Science.gov (United States)

    Ward, D. J.

    2016-11-01

    Fusion remains the main source of energy generation in the Universe and is indirectly the origin of nearly all terrestrial energy (including fossil fuels) but it is the only fundamental energy source not used directly on Earth. Here we look at the characteristics of Earth-based fusion power, how it might contribute to future energy supply and what that tells us about the future direction of the R&D programme. The focus here is Magnetic Confinement Fusion although many of the points apply equally to inertial confinement fusion.

  10. Challenges Surrounding the Injection and Arrival of Targets at LIFE Fusion Chamber Center

    Energy Technology Data Exchange (ETDEWEB)

    Miles, R; Spaeth, M; Manes, K; Amendt, P; Tabak, M; Bond, T; Kucheyev, S; Latkowski, J; Loosmore, G; Bliss, E; Baker, K; Bhandarkar, S; Petzoldt, R; Alexander, N; Tillack, M; Holdener, D

    2010-12-01

    IFE target designers must consider several engineering requirements in addition to the physics requirements for successful target implosion. These considerations include low target cost, high manufacturing throughput, the ability of the target to survive the injection into the fusion chamber and arrive in a condition and physical position consistent with proper laser-target interaction and ease of post-implosion debris removal. This article briefly describes these considerations for the Laser Inertial Fusion-based Energy (LIFE) targets currently being designed.

  11. Z-pinch driven fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    SLUTZ,STEPHEN A.; OLSON,CRAIG L.; ROCHAU,GARY E.; DERZON,MARK S.; PETERSON,P.F.; DEGROOT,J.S.; JENSEN,N.; MILLER,G.

    2000-05-30

    The Z machine at Sandia National Laboratories (SNL) is the most powerful multi-module synchronized pulsed-power accelerator in the world. Rapid development of z-pinch loads on Z has led to outstanding progress in the last few years, resulting in radiative powers of up to 280 TW in 4 ns and a total radiated x-ray energy of 1.8 MJ. The present goal is to demonstrate single-shot, high-yield fusion capsules. Pulsed power is a robust and inexpensive technology, which should be well suited for Inertial Fusion Energy, but a rep-rated capability is needed. Recent developments have led to a viable conceptual approach for a rep-rated z-pinch power plant for IFE. This concept exploits the advantages of going to high yield (a few GJ) at low rep-rate ({approximately} 0.1 Hz), and using a Recyclable Transmission Line (RTL) to provide the necessary standoff between the fusion target and the power plant chamber. In this approach, a portion of the transmission line near the capsule is replaced after each shot. The RTL should be constructed of materials that can easily be separated from the liquid coolant stream and refabricated for a subsequent shots. One possibility is that most of the RTL is formed by casting FLiBe, a salt composed of fluorine, lithium, and beryllium, which is an attractive choice for the reactor coolant, with chemically compatible lead or tin on the surface to provide conductivity. The authors estimate that fusion yields greater than 1 GJ will be required for efficient generation of electricity. Calculations indicate that the first wall will have an acceptable lifetime with these high yields if blast mitigation techniques are used. Furthermore, yields above 5 GJ may allow the use of a compact blanket direct conversion scheme.

  12. 21 CFR 886.1880 - Fusion and stereoscopic target.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Fusion and stereoscopic target. 886.1880 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1880 Fusion and stereoscopic target. (a) Identification. A fusion and stereoscopic target is a device intended for use as a viewing...

  13. The perspectives of fusion energy: The roadmap towards energy production and fusion energy in a distributed energy system

    DEFF Research Database (Denmark)

    Naulin, Volker; Juul Rasmussen, Jens; Korsholm, Søren Bang

    2014-01-01

    Controlled thermonuclear fusion has the potential of providing an environmentally friendly and inexhaustible energy source for mankind. Fusion energy, which powers our sun and the stars, is released when light elements, such as the hydrogen isotopes deuterium and tritium, fuse together. This occurs...... The presentation will discuss the present status of the fusion energy research and review the EU Roadmap towards a fusion power plant. Further the cost of fusion energy is assessed as well as how it can be integrated in the distributed energy system...

  14. Accelerator-based fusion with a low temperature target

    Science.gov (United States)

    Phillips, R. E.; Ordonez, C. A.

    2013-04-01

    Neutron generators are in use in a number of scientific and commercial endeavors. They function by triggering fusion reactions between accelerated ions (usually deuterons) and a stationary cold target (e.g., containing tritium). This setup has the potential to generate energy. It has been shown that if the energy transfer between injected ions and target electrons is sufficiently small, net energy gain can be achieved. Three possible avenues are: (a) a hot target with high electron temperature, (b) a cold non-neutral target with an electron deficiency, or (c) a cold target with a high Fermi energy. A study of the third possibility is reported in light of recent research that points to a new phase of hydrogen, which is hypothesized to be related to metallic hydrogen. As such, the target is considered to be composed of nuclei and delocalized electrons. The electrons are treated as conduction electrons, with the average minimum excitation energy being approximately equal to 40% of the Fermi energy. The Fermi energy is directly related to the electron density. Preliminary results indicate that if the claimed electron densities in the new phase of hydrogen were achieved in a target, the energy transfer to electrons would be small enough to allow net energy gain.

  15. The Parameter Space of Magnetized Target Fusion (aka Magneto-Inertial Fusion)

    Science.gov (United States)

    Lindemuth, Irvin

    2016-10-01

    Magnetized Target Fusion (MTF), aka Magneto-Inertial Fusion (MIF), is an approach to fusion that compresses a preformed, magnetized (but not necessarily magnetically confined) plasma with an imploding liner or pusher. MTF/MIF operates in a density regime in between the eleven orders of magnitude (1011) in density that separate inertial confinement fusion (ICF) from magnetic confinement fusion MCF. Compared to MCF, the higher density, shorter confinement times, and compressional heating as the dominant heating mechanism potentially reduce the impact of magnetic instabilities. Compared to ICF, the magnetically reduced thermal transport and lower density leads to orders-of-magnitude reduction in the difficult-to-achieve areal-density parameter and a significant reduction in required implosion velocity and radial convergence, potentially reducing the deleterious effects of implosion hydrodynamic instabilities. This tutorial presents fundamental analysis and simple time-dependent modeling to show where significant fusion gain might be achieved in the intermediate-density regime. The analysis shows that the fusion design space is potentially a continuum between ICF and MCF but practical considerations limit the space in which ignition might be obtained. Generic time-dependent modeling addresses the key physics requirements and defines ``ball-park'' values needed for target-plasma initial density, temperature, and magnetic field and implosion system size, energy, and velocity. The modeling shows energy gains greater than 30 can potentially be achieved and that high gain may be obtained at low convergence ratios, e.g., less than 15. A non-exhaustive review of past and present MTF/MIF efforts is presented and the renewed interest in MTF/MIF within the US (e.g., ARPA-E's ALPHA program) and abroad is noted.

  16. Magnetic confinement fusion energy research

    Energy Technology Data Exchange (ETDEWEB)

    Grad, H

    1977-03-01

    Controlled Thermonuclear Fusion offers probably the only relatively clean energy solution with completely inexhaustible fuel and unlimited power capacity. The scientific and technological problem consists in magnetically confining a hot, dense plasma (pressure several to hundreds of atmospheres, temperature 10/sup 8/ degrees or more) for an appreciable fraction of a second. The scientific and mathematical problem is to describe the behavior, such as confinement, stability, flow, compression, heating, energy transfer and diffusion of this medium in the presence of electromagnetic fields just as we now can for air or steam. Some of the extant theory consists of applications, routine or ingenious, of known mathematical structures in the theory of differential equations and in traditional analysis. Other applications of known mathematical structures offer surprises and new insights: the coordination between sub-supersonic and elliptic-hyperbolic is fractured; supersonic propagation goes upstream; etc. Other completely nonstandard mathematical structures with significant theory are being rapidly uncovered (and somewhat less rapidly understood) such as non-elliptic variational equations and new types of weak solutions. It is these new mathematical structures which one should expect to supply the foundation for the next generation's pure mathematics, if history is a guide. Despite the substantial effort over a period of some twenty years, there are still basic and important scintific and mathematical discoveries to be made, lying just beneath the surface.

  17. Magnetized Target Fusion Driven by Plasma Liners

    Science.gov (United States)

    Thio, Y. C. Francis; Cassibry, Jason; Eskridge, Richard; Kirkpatrick, Ronald C.; Knapp, Charles E.; Lee, Michael; Martin, Adam; Smith, James; Wu, S. T.; Rodgers, Stephen L. (Technical Monitor)

    2001-01-01

    For practical applications of magnetized target fusion, standoff drivers to deliver the imploding momentum flux to the target plasma remotely are required. Quasi-spherically converging plasma jets have been proposed as standoff drivers for this purpose. The concept involves the dynamic formation of a quasi-spherical plasma liner by the merging of plasma jets, and the use of the liner so formed to compress a spheromak or a field reversed configuration (FRC). Theoretical analysis and computer modeling of the concept are presented. It is shown that, with the appropriate choice of the flow parameters in the liner and the target, the impact between the liner and the target plasma can be made to be shockless in the liner or to generate at most a very weak shock in the liner. Additional information is contained in the original extended abstract.

  18. Fusion the energy of the universe

    CERN Document Server

    McCracken, Garry

    2012-01-01

    Fusion: The Energy of the Universe, 2e is an essential reference providing basic principles of fusion energy from its history to the issues and realities progressing from the present day energy crisis. The book provides detailed developments and applications for researchers entering the field of fusion energy research. This second edition includes the latest results from the National Ignition Facility at the Lawrence Radiation Laboratory at Livermore, CA, and the progress on the International Thermonuclear Experimental Reactor (ITER) tokamak programme at Caderache, France.

  19. The ignition design space of magnetized target fusion

    Energy Technology Data Exchange (ETDEWEB)

    Lindemuth, Irvin R. [2490 North Grannen Road, Tucson, Arizona 85745 (United States)

    2015-12-15

    The simple magnetized target implosion model of Lindemuth and Kirkpatrick [Nucl. Fusion 23, 263 (1983)] has been extended to survey the potential parameter space in which three types of magnetized targets—cylindrical with axial magnetic field, cylindrical with azimuthal magnetic field, and spherical with azimuthal magnetic field—might achieve ignition and produce large gain at achievable radial convergence ratios. The model has been used to compute the dynamic, time-dependent behavior of many initial parameter sets that have been based upon projected ignition conditions using the quasi-adiabatic and quasi-flux-conserving properties of magnetized target implosions. The time-dependent calculations have shown that energy gains greater than 30 can potentially be achieved for each type of target. By example, it is shown that high gain may be obtained at extremely low convergence ratios, e.g., less than 15, for appropriate initial conditions. It is also shown that reaching the ignition condition, i.e., when fusion deposition rates equal total loss rates, does not necessarily lead to high gain and high fuel burn-up. At the lower densities whereby fusion temperatures can be reached in magnetized targets, the fusion burn rate may be only comparable with the hydrodynamic heating/cooling rates. On the other hand, when the fusion burn rates significantly exceed the hydrodynamic rates, the calculations show a characteristic rapid increase in temperature due to alpha particle deposition with a subsequent increased burn rate and high gain. A major result of this paper is that each type of target operates in a different initial density-energy-velocity range. The results of this paper provide initial target plasma parameters and driver parameters that can be used to guide plasma formation and driver development for magnetized targets. The results indicate that plasmas for spherical, cylindrical with azimuthal field, and cylindrical with axial field targets must have an initial

  20. Pulsed Power Driven Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    SLUTZ,STEPHEN A.

    1999-11-22

    Pulsed power is a robust and inexpensive technology for obtaining high powers. Considerable progress has been made on developing light ion beams as a means of transporting this power to inertial fusion capsules. However, further progress is hampered by the lack of an adequate ion source. Alternatively, z-pinches can efficiently convert pulsed power into thermal radiation, which can be used to drive an inertial fusion capsule. However, a z-pinch driven fusion explosion will destroy a portion of the transmission line that delivers the electrical power to the z-pinch. They investigate several options for providing standoff for z-pinch driven fusion. Recyclable Transmission Lines (RTLs) appear to be the most promising approach.

  1. Final report on the Magnetized Target Fusion Collaboration

    Energy Technology Data Exchange (ETDEWEB)

    John Slough

    2009-09-08

    Nuclear fusion has the potential to satisfy the prodigious power that the world will demand in the future, but it has yet to be harnessed as a practical energy source. The entry of fusion as a viable, competitive source of power has been stymied by the challenge of finding an economical way to provide for the confinement and heating of the plasma fuel. It is the contention here that a simpler path to fusion can be achieved by creating fusion conditions in a different regime at small scale (~ a few cm). One such program now under study, referred to as Magnetized Target Fusion (MTF), is directed at obtaining fusion in this high energy density regime by rapidly compressing a compact toroidal plasmoid commonly referred to as a Field Reversed Configuration (FRC). To make fusion practical at this smaller scale, an efficient method for compressing the FRC to fusion gain conditions is required. In one variant of MTF a conducting metal shell is imploded electrically. This radially compresses and heats the FRC plasmoid to fusion conditions. The closed magnetic field in the target plasmoid suppresses the thermal transport to the confining shell, thus lowering the imploding power needed to compress the target. The undertaking to be described in this proposal is to provide a suitable target FRC, as well as a simple and robust method for inserting and stopping the FRC within the imploding liner. The timescale for testing and development can be rapidly accelerated by taking advantage of a new facility funded by the Department of Energy. At this facility, two inductive plasma accelerators (IPA) were constructed and tested. Recent experiments with these IPAs have demonstrated the ability to rapidly form, accelerate and merge two hypervelocity FRCs into a compression chamber. The resultant FRC that was formed was hot (T&ion ~ 400 eV), stationary, and stable with a configuration lifetime several times that necessary for the MTF liner experiments. The accelerator length was less than

  2. A Plan for the Development of Fusion Energy. Final Report to Fusion Energy Sciences Advisory Committee, Fusion Development Path Panel

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2003-03-05

    This report presents a plan for the deployment of a fusion demonstration power plant within 35 years, leading to commercial application of fusion energy by mid-century. The plan is derived from the necessary features of a demonstration fusion power plant and from the time scale defined by President Bush. It identifies critical milestones, key decision points, needed major facilities and required budgets.

  3. Atmospheric type modes in laser fusion targets

    Science.gov (United States)

    Scannapieco, A. J.

    1981-09-01

    The fluid stability of laser-fusion targets is considered as a stability problem of a pseudo-planetary atmosphere. Three atmospheric type modes are studied; acoustic, gravity, and Lamb modes. The changing character (i.e., growing, oscillatory, or growing-oscillatory) of each is investigated as a function of the density-gradient scale length H of the fluid. A growing class of modes is found which is distinct from the gravity (i.e., Taylor) mode if a gradient in entropy exists in the fluid. These modes are shown to be overstable Lamb modes. Also, the gravity mode is only stable for a distinct band of values of H. These values, at which the density and Lamb modes change character, are derived from the dispersion relation for the modes. Finally, the consequences for laser targets are discussed.

  4. Fire hazard analysis for fusion energy experiments

    Energy Technology Data Exchange (ETDEWEB)

    Alvares, N.J.; Hasegawa, H.K.

    1979-01-01

    The 2XIIB mirror fusion facility at Lawrence Livermore Laboratory (LLL) was used to evaluate the fire safety of state-of-the-art fusion energy experiments. The primary objective of this evaluation was to ensure the parallel development of fire safety and fusion energy technology. Through fault-tree analysis, we obtained a detailed engineering description of the 2XIIB fire protection system. This information helped us establish an optimum level of fire protection for experimental fusion energy facilities as well as evaluate the level of protection provided by various systems. Concurrently, we analyzed the fire hazard inherent to the facility using techniques that relate the probability of ignition to the flame spread and heat-release potential of construction materials, electrical and thermal insulations, and dielectric fluids. A comparison of the results of both analyses revealed that the existing fire protection system should be modified to accommodate the range of fire hazards inherent to the 2XIIB facility.

  5. A global energy model with fusion

    Energy Technology Data Exchange (ETDEWEB)

    Lechon, Yolanda [CIEMAT, Avda Complutense 22, 28040 Madrid (Spain)]. E-mail: yolanda.lechon@ciemat.es; Cabal, H. [CIEMAT, Avda Complutense 22, 28040 Madrid (Spain); Varela, M. [CIEMAT, Avda Complutense 22, 28040 Madrid (Spain); Saez, R. [CIEMAT, Avda Complutense 22, 28040 Madrid (Spain); Eherer, C. [TUG/ITP, Petersgasse 16, 8010 Graz (Austria); Baumann, M. [TUG/ITP, Petersgasse 16, 8010 Graz (Austria); Dueweke, J. [IPP, Boltzmannstr. 2, D-85748 Garching (Germany); Hamacher, T. [IPP, Boltzmannstr. 2, D-85748 Garching (Germany); Tosato, G.C. [EFDA Close Support Unit, Boltzmannstr. 2, D-85748 Garching (Germany)

    2005-11-15

    Some analysts expect a complete shift of the global energy system in the 21st century, away from fossil fuels to either renewable sources or new nuclear technologies [L. Schrattenholzer, A roadmap to a sustainable global energy system, in: Proceedings of the International Energy Workshop, Paris, June, 2004]. Fusion might become a corner stone of the future energy system. The construction and successful operation of ITER is a necessary condition to reach this goal. Within the Socio Economic Research on Fusion (SERF) programme guided by EFDA, a consortium between CIEMAT, TU Graz (TUG), ENEA and IPP open to other European energy and fusion research laboratories has been formed to analyse the possible role of fusion in the future energy system. Using TIMES, a single region global model has been constructed including fusion as an energy option. Background of the model is a detailed bottom-up description of the complete energy system starting from mining process up to the various demand sectors. The model dynamics is determined by an optimisation process, in which total surplus is maximized. The paper will present the first attempts to set-up a single region global model and the first results.

  6. Integrated Chamber Design for the Laser Inertial Fusion Energy (LIFE) Engine

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J F; Kramer, K J; Abbott, R P; Morris, K R; DeMuth, J; Divol, L; El-Dasher, B; Lafuente, A; Loosmore, G; Reyes, S; Moses, G A; Fratoni, M; Flowers, D; Aceves, S; Rhodes, M; Kane, J; Scott, H; Kramer, R; Pantano, C; Scullard, C; Sawicki, R; Wilks, S; Mehl, M

    2010-12-07

    The Laser Inertial Fusion Energy (LIFE) concept is being designed to operate as either a pure fusion or hybrid fusion-fission system. A key component of a LIFE engine is the fusion chamber subsystem. The present work details the chamber design for the pure fusion option. The fusion chamber consists of the first wall and blanket. This integrated system must absorb the fusion energy, produce fusion fuel to replace that burned in previous targets, and enable both target and laser beam transport to the ignition point. The chamber system also must mitigate target emissions, including ions, x-rays and neutrons and reset itself to enable operation at 10-15 Hz. Finally, the chamber must offer a high level of availability, which implies both a reasonable lifetime and the ability to rapidly replace damaged components. An integrated LIFE design that meets all of these requirements is described herein.

  7. Impact of target modifications on Magnetized Liner Inertial Fusion performance

    Science.gov (United States)

    Gomez, Matthew; Knapp, Patrick; Sefkow, Adam; Slutz, Stephen; Awe, Thomas; Hansen, Stephanie; Hahn, Kelly; Harding, Eric; Jennings, Christopher; McBride, Ryan; Sinars, Daniel; Rochau, Gregory; Peterson, Kyle

    2015-11-01

    Magnetized Liner Inertial Fusion (MagLIF) is a magnetically-driven fusion concept in which an axial magnetic field and laser heating are used to relax the implosion requirements of inertial confinement fusion. Initial experiments demonstrated the promise of the concept with relatively high yields (primary DD = 2e12), ion temperatures (2.5 keV), and magnetic field-radius products (>0.3 MG-cm). In order to better understand the portions of parameter space in which MagLIF can operate effectively, a series of experiments are being conducted to test the impact of various changes (e.g., laser-entrance-hole window thickness, imploding height of the target, endcap material, laser energy, laser spot size, initial fuel density). The impact of these changes on target performance (primary neutron yield, ion temperature, stagnation volume, etc.) will be discussed. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract No. DE-AC04-94AL85000.

  8. Plasmonic energy nanofocusing for high-efficiency laser fusion ignition

    Science.gov (United States)

    Tanabe, Katsuaki

    2016-08-01

    We propose an efficient laser fusion ignition system consisting of metal nanoparticles or nanoshells embedded in conventional deuterated polystyrene fuel targets. The incident optical energy of the heating laser is highly concentrated around the metallic particulates randomly dispersed inside imploded targets due to the electromagnetic-field-enhancement effect by surface plasmon resonance, and thus effectively triggers nuclear-fusion chain reactions. Our preliminary calculations exhibit field enhancement factors of around 50 and 1100 for spherical Ag nanoparticles and Ag/SiO2 nanoshells, respectively, in the 1-µm band.

  9. Converting energy from fusion into useful forms

    CERN Document Server

    Kovari, M; Jenkins, I; Kiely, C

    2014-01-01

    If fusion power reactors are to be feasible, it will still be necessary to convert the energy of the nuclear reaction into usable form. The heat produced will be removed from the reactor core by a primary coolant, which might be water, helium, molten lithium-lead, molten lithium-containing salt, or CO2. The heat could then be transferred to a conventional Rankine cycle or Brayton (gas turbine) cycle. Alternatively it could be used for thermochemical processes such as producing hydrogen or other transport fuels. Fusion presents new problems because of the high energy neutrons released. These affect the selection of materials and the operating temperature, ultimately determining the choice of coolant and working cycle. The limited temperature ranges allowed by present day irradiated structural materials, combined with the large internal power demand of the plant, will limit the overall thermal efficiency. The operating conditions of the fusion power source, the materials, coolant, and energy conversion system w...

  10. 0.5MJ Targets for an IFE Fusion Test Facility

    Science.gov (United States)

    Lafortune, K. N.; Perkins, L. J.; Bedrossian, P.; Betti, R.; Schmitt, A.; Obenschain, S.

    2006-10-01

    There has been much recent progress in the development of both the source and targets for laser-driven, inertial confinement fusion (ICF). The next step to apply this approach to inertial fusion energy (IFE) is to build a facility that has all the required components of a reactor and demonstrates the reliability and robustness. The Fusion Test Facility proposed by NRL is one such facility [S.Obenschain, Bull. APS v50, 2005]. The cost, complexity and scale of any fusion test facility are driven by the energy required for the fusion target. As the laser-target physics has become better understood, target geometries that require less drive energy have been found. Using conventional hotspot ignition, rad-hydro-burn simulations using HYDRA of low-drive-energy, direct-drive reactor targets requiring just 0.5 MJ of drive energy to achieve gain of 10's are being studied. 1-D scoping studies have been performed to outline the source requirements. Good agreement with comprehensive, time-dependent 1-D simulations in LASNEX has been obtained for integral quantities such as gain, yield and ignition margins. The robustness of the small targets has been explored with 2-D stability studies. Shock ignition of similar targets could be employed to achieve yet higher gains with similar drive energies.

  11. Alternative Approaches to High Energy Density Fusion

    Science.gov (United States)

    Hammer, J.

    2016-10-01

    This paper explores selected approaches to High Energy Density (HED) fusion, beginning with discussion of ignition requirements at the National Ignition Facility (NIF). The needed improvements to achieve ignition are closely tied to the ability to concentrate energy in the implosion, manifested in the stagnation pressure, Pstag. The energy that must be assembled in the imploded state to ignite varies roughly as Pstag-2, so among other requirements, there is a premium on reaching higher Pstag to achieve ignition with the available laser energy. The U.S. inertial confinement fusion program (ICF) is pursuing higher Pstag on NIF through improvements to capsule stability and symmetry. One can argue that recent experiments place an approximate upper bound on the ultimate ignition energy requirement. Scaling the implosions consistently in spatial, temporal and energy scales shows that implosions of the demonstrated quality ignite robustly at 9-15 times the current energy of NIF. While lasers are unlikely to reach that bounding energy, it appears that pulsed-power sources could plausibly do so, giving a range of paths forward for ICF depending on success in improving energy concentration. In this paper, I show the scaling arguments then discuss topics from my own involvement in HED fusion. The recent Viewfactor experiments at NIF have shed light on both the observed capsule drive deficit and errors in the detailed modelling of hohlraums. The latter could be important factors in the inability to achieve the needed symmetry and energy concentration. The paper then recounts earlier work in Fast Ignition and the uses of pulsed-power for HED and fusion applications. It concludes with a description of a method for improving pulsed-power driven hohlraums that could potentially provide a factor of 10 in energy at NTF-like drive conditions and reach the energy bound for indirect drive ICF.

  12. On the path to fusion energy

    Science.gov (United States)

    Tabak, M.

    2016-10-01

    There is a need to develop alternate energy sources in the coming century because fossil fuels will become depleted and their use may lead to global climate change. Inertial fusion can become such an energy source, but significant progress must be made before its promise is realized. The high-density approach to inertial fusion suggested by Nuckolls et al. leads reaction chambers compatible with civilian power production. Methods to achieve the good control of hydrodynamic stability and implosion symmetry required to achieve these high fuel densities will be discussed. Fast Ignition, a technique that achieves fusion ignition by igniting fusion fuel after it is assembled, will be described along with its gain curves. Fusion costs of energy for conventional hotspot ignition will be compared with those of Fast Ignition and their capital costs compared with advanced fission plants. Finally, techniques that may improve possible Fast Ignition gains by an order of magnitude and reduce driver scales by an order of magnitude below conventional ignition requirements are described.

  13. Indirect drive targets for fusion power

    Energy Technology Data Exchange (ETDEWEB)

    Amendt, Peter A.; Miles, Robin R.

    2016-10-11

    A hohlraum for an inertial confinement fusion power plant is disclosed. The hohlraum includes a generally cylindrical exterior surface, and an interior rugby ball-shaped surface. Windows over laser entrance holes at each end of the hohlraum enclose inert gas. Infrared reflectors on opposite sides of the central point reflect fusion chamber heat away from the capsule. P2 shields disposed on the infrared reflectors help assure an enhanced and more uniform x-ray bath for the fusion fuel capsule.

  14. 78 FR 48863 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2013-08-12

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... that the Fusion Energy Sciences Advisory Committee will be renewed for a two-year period beginning on..., priorities, and strategies for advancing plasma science, fusion science and fusion technology--the...

  15. Magnetized Plasma Compression for Fusion Energy

    Science.gov (United States)

    Degnan, James; Grabowski, Christopher; Domonkos, Matthew; Amdahl, David

    2013-10-01

    Magnetized Plasma Compression (MPC) uses magnetic inhibition of thermal conduction and enhancement of charge particle product capture to greatly reduce the temporal and spatial compression required relative to un-magnetized inertial fusion (IFE)--to microseconds, centimeters vs nanoseconds, sub-millimeter. MPC greatly reduces the required confinement time relative to MFE--to microseconds vs minutes. Proof of principle can be demonstrated or refuted using high current pulsed power driven compression of magnetized plasmas using magnetic pressure driven implosions of metal shells, known as imploding liners. This can be done at a cost of a few tens of millions of dollars. If demonstrated, it becomes worthwhile to develop repetitive implosion drivers. One approach is to use arrays of heavy ion beams for energy production, though with much less temporal and spatial compression than that envisioned for un-magnetized IFE, with larger compression targets, and with much less ambitious compression ratios. A less expensive, repetitive pulsed power driver, if feasible, would require engineering development for transient, rapidly replaceable transmission lines such as envisioned by Sandia National Laboratories. Supported by DOE-OFES.

  16. Identification of targetable FGFR gene fusions in diverse cancers.

    Science.gov (United States)

    Wu, Yi-Mi; Su, Fengyun; Kalyana-Sundaram, Shanker; Khazanov, Nickolay; Ateeq, Bushra; Cao, Xuhong; Lonigro, Robert J; Vats, Pankaj; Wang, Rui; Lin, Su-Fang; Cheng, Ann-Joy; Kunju, Lakshmi P; Siddiqui, Javed; Tomlins, Scott A; Wyngaard, Peter; Sadis, Seth; Roychowdhury, Sameek; Hussain, Maha H; Feng, Felix Y; Zalupski, Mark M; Talpaz, Moshe; Pienta, Kenneth J; Rhodes, Daniel R; Robinson, Dan R; Chinnaiyan, Arul M

    2013-06-01

    Through a prospective clinical sequencing program for advanced cancers, four index cases were identified which harbor gene rearrangements of FGFR2, including patients with cholangiocarcinoma, breast cancer, and prostate cancer. After extending our assessment of FGFR rearrangements across multiple tumor cohorts, we identified additional FGFR fusions with intact kinase domains in lung squamous cell cancer, bladder cancer, thyroid cancer, oral cancer, glioblastoma, and head and neck squamous cell cancer. All FGFR fusion partners tested exhibit oligomerization capability, suggesting a shared mode of kinase activation. Overexpression of FGFR fusion proteins induced cell proliferation. Two bladder cancer cell lines that harbor FGFR3 fusion proteins exhibited enhanced susceptibility to pharmacologic inhibition in vitro and in vivo. Because of the combinatorial possibilities of FGFR family fusion to a variety of oligomerization partners, clinical sequencing efforts, which incorporate transcriptome analysis for gene fusions, are poised to identify rare, targetable FGFR fusions across diverse cancer types.

  17. Proceedings of the Second Fusion-Fission Energy Systems Review Meeting

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-11-02

    The agenda of the meeting was developed to address, in turn, the following major areas: specific problem areas in nuclear energy systems for application of fusion-fission concepts; current and proposed fusion-fission programs in response to the identified problem areas; target costs and projected benefits associated with fusion-fission energy systems; and technical problems associated with the development of fusion-fission concepts. The greatest emphasis was placed on the characteristics of and problems, associated with fuel producing fusion-fission hybrid reactors.

  18. Proceedings of the Second Fusion-Fission Energy Systems Review Meeting

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-11-02

    The agenda of the meeting was developed to address, in turn, the following major areas: specific problem areas in nuclear energy systems for application of fusion-fission concepts; current and proposed fusion-fission programs in response to the identified problem areas; target costs and projected benefits associated with fusion-fission energy systems; and technical problems associated with the development of fusion-fission concepts. The greatest emphasis was placed on the characteristics of and problems, associated with fuel producing fusion-fission hybrid reactors.

  19. 77 FR 485 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2012-01-05

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... open meeting. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory Committee.... Synakowski, Designated Federal Officer, Office of Fusion Energy Sciences; U.S. Department of Energy;...

  20. 78 FR 2259 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2013-01-10

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... open meeting. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory Committee.... Synakowski, Designated Federal Officer, Office of Fusion Energy Sciences; U.S. Department of Energy;...

  1. 76 FR 40714 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2011-07-11

    ... Fusion Energy Sciences Advisory Committee AGENCY: Department of Energy, Office of Science. ACTION: Notice of open meeting. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory... CONTACT: Albert L. Opdenaker, Designated Federal Officer, Office of Fusion Energy Sciences;...

  2. 78 FR 15937 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2013-03-13

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... open meeting. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory Committee..., Designated Federal Officer, Office of Fusion Energy Sciences; U.S. Department of Energy; 1000...

  3. Pionic Fusion at Subthreshold Energies

    Science.gov (United States)

    Joulaeizadeh, L.; Bacelar, J.; Eslami-Kalantari, M.; Gašparić, I.; Kalantar-Nayestanaki, N.; Löhner, H.; Mardanpour, H.; Messchendorp, J. G.; Moeini, H.; Ramazani-Moghaddam-Arani, A.; Shende, S. V.; Stephan, E.

    In order to study the role of pions and clustering phenomena in nuclei, two experiments have been performed using the AGOR accelerator facility. In collisions of two nuclei a pion and a fused nucleus were produced. The examined reactions were 4He(3He, π0)7Be and 6Li(4He, π0)10B at beam energies about 10 MeV above the coherent pion production threshold (256 MeV and 236.4 MeV, respectively). Since the available energy is well below the pion production threshold in an elementary nucleon-nucleon process, a highly coherent mechanism is needed. We identified the reaction by measuring the fused system in the magnetic spectrometer and the produced neutral pions in the Plastic Ball detection system with large acceptance. Our experimental setup provided the exclusive cross sections by identifying all products in overdetermined kinematics. Here we present the preliminary results of the analysis for the second reaction. Angular distribution of neutral pions will be discussed.

  4. Energy Dependence of the Fusion Barrier for Heavy Nuclear Systems

    Institute of Scientific and Technical Information of China (English)

    LIZhu-xia; WUXi-zhen; TIANJun-long; WANGNing

    2003-01-01

    The dynamical behavior of the fusion potential barrier for heavy nuclear systems is studied by means of the improved quantum molecular dynamics model. It is found that the fusion potential barrier experienced in a realistic fusion process (the dynamic fusion potential barrier) reduces with decrease of incident energies.

  5. Measuring fusion excitation functions with RIBs using the stacked target technique: Problems and possible solutions

    Directory of Open Access Journals (Sweden)

    Fisichella M.

    2016-01-01

    Full Text Available For measuring fusion excitation functions, the activation technique with a stack of targets offers the considerable advantage that several reaction energies may be simultaneously measured by using one beam energy. However, its main drawback is the degradation of the beam quality as it passes through the stack due to statistical nature of energy loss processes and any non-uniformity of the stacked targets. If not taken properly into account, this degradation can lead to a wrong determination of the fusion excitation function. In this contribution some results of the investigation of this problem are reported.

  6. Fusion energy - an abundant energy source for the future

    DEFF Research Database (Denmark)

    this goal, mankind will have a sustainable base load energy source with abundant resources, having no CO2 release, and with no longlived radioactive waste. This presentation will describe the basics of fusion energy production and the status and future prospects of the research. Considerations...

  7. Molecular pathways: targeting ETS gene fusions in cancer.

    Science.gov (United States)

    Feng, Felix Y; Brenner, J Chad; Hussain, Maha; Chinnaiyan, Arul M

    2014-09-01

    Rearrangements, or gene fusions, involving the ETS family of transcription factors are common driving events in both prostate cancer and Ewing sarcoma. These rearrangements result in pathogenic expression of the ETS genes and trigger activation of transcriptional programs enriched for invasion and other oncogenic features. Although ETS gene fusions represent intriguing therapeutic targets, transcription factors, such as those comprising the ETS family, have been notoriously difficult to target. Recently, preclinical studies have demonstrated an association between ETS gene fusions and components of the DNA damage response pathway, such as PARP1, the catalytic subunit of DNA protein kinase (DNAPK), and histone deactylase 1 (HDAC1), and have suggested that ETS fusions may confer sensitivity to inhibitors of these DNA repair proteins. In this review, we discuss the role of ETS fusions in cancer, the preclinical rationale for targeting ETS fusions with inhibitors of PARP1, DNAPK, and HDAC1, as well as ongoing clinical trials targeting ETS gene fusions. ©2014 American Association for Cancer Research.

  8. High-energy krypton fluoride lasers for inertial fusion.

    Science.gov (United States)

    Obenschain, Stephen; Lehmberg, Robert; Kehne, David; Hegeler, Frank; Wolford, Matthew; Sethian, John; Weaver, James; Karasik, Max

    2015-11-01

    Laser fusion researchers have realized since the 1970s that the deep UV light from excimer lasers would be an advantage as a driver for robust high-performance capsule implosions for inertial confinement fusion (ICF). Most of this research has centered on the krypton-fluoride (KrF) laser. In this article we review the advantages of the KrF laser for direct-drive ICF, the history of high-energy KrF laser development, and the present state of the art and describe a development path to the performance needed for laser fusion and its energy application. We include descriptions of the architecture and performance of the multi-kilojoule Nike KrF laser-target facility and the 700 J Electra high-repetition-rate KrF laser that were developed at the U.S. Naval Research Laboratory. Nike and Electra are the most advanced KrF lasers for inertial fusion research and energy applications.

  9. 76 FR 49757 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2011-08-11

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... that the Fusion Energy Sciences Advisory Committee will be renewed for a two-year period beginning on...-range plans, priorities, and strategies for advancing plasma science, fusion science, and...

  10. 75 FR 8685 - Fusion Energy Sciences Advisory Committee

    Science.gov (United States)

    2010-02-25

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... open meeting. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory Committee..., Gaithersburg, Maryland 20877. FOR FURTHER INFORMATION CONTACT: Albert L. Opdenaker, Office of Fusion...

  11. Laser Inertial Fusion-based Energy: Neutronic Design Aspects of a Hybrid Fusion-Fission Nuclear Energy System

    OpenAIRE

    Kramer, Kevin James

    2010-01-01

    This study investigates the neutronics design aspects of a hybrid fusion-fission energy system called the Laser Fusion-Fission Hybrid (LFFH). A LFFH combines current Laser Inertial Confinement fusion technology with that of advanced fission reactor technology to produce a system that eliminates many of the negative aspects of pure fusion or pure fission systems. When examining the LFFH energy mission, a significant portion of the United States and world energy production could be supplied by ...

  12. On Stability of Targets for Plasma Jet Induced Magnetoinertial Fusion

    CERN Document Server

    Samulyak, Roman; Kim, Hyoungekun

    2015-01-01

    The compression and stability of plasma targets for the plasma jet-induced magneto-inertial fusion (PJMIF) have been investigated via large scale simulations using the FronTier code capable of explicit tracking of material interfaces. In the PJMIF concept, a plasma liner, formed by the merger of a large number of radial, highly supersonic plasma jets, implodes on a magnetized plasma target and compresses it to conditions of the fusion ignition. A multi-stage computational approach for simulations of the liner-target interaction and the compression of plasma targets has been developed to minimize computing time. Simulations revealed important features of the target compression process, including instability and disintegration of targets. The non-uniformity of the leading edge of the liner, caused by plasma jets as well as oblique shock waves between them, leads to instabilities during the target compression. By using front tracking, the evolution of targets has been studied in 3-dimensional simulations. Optimi...

  13. Inertial Fusion Energy at Denim (Spain)

    Energy Technology Data Exchange (ETDEWEB)

    Velarde, G.

    2005-07-01

    The paper describes the history and the research carried out in the field on Inertial Confinement Fusion (ICF) since 1966 at the Spanish Atomic Energy Commission (JEN) up to present time at the Institute of Nuclear Fusion (DENIM) of the Polytechnic University of Madrid (UPM), Late in the 70s, we developed the NORCLA code that was the first non-classified coupled code to analyze the different processes held in ICF. Since then, we have developed a set of more accurate codes such as the ARWEN (two-dimensional transport), JIMENA and ANALOP (Atomic physics), ACAB (safety and environmental), material and reactor chambers and advanced fuels. The paper tells also the origins of DENIM and all the efforts made to achieve an international declassification in ICF research. (Author)

  14. BOOK REVIEW: Fusion: The Energy of the Universe

    Science.gov (United States)

    Lister, J.

    2006-05-01

    This book outlines the quest for fusion energy. It is presented in a form which is accessible to the interested layman, but which is precise and detailed for the specialist as well. The book contains 12 detailed chapters which cover the whole of the intended subject matter with copious illustrations and a balance between science and the scientific and political context. In addition, the book presents a useful glossary and a brief set of references for further non-specialist reading. Chapters 1 to 3 treat the underlying physics of nuclear energy and of the reactions in the sun and in the stars in considerable detail, including the creation of the matter in the universe. Chapter 4 presents the fusion reactions which can be harnessed on earth, and poses the fundamental problems of realising fusion energy as a source for our use, explaining the background to the Lawson criterion on the required quality of energy confinement, which 50 years later remains our fundamental milestone. Chapter 5 presents the basis for magnetic confinement, introducing some early attempts as well as some straightforward difficulties and treating linear and circular devices. The origins of the stellarator and of the tokamak are described. Chapter 6 is not essential to the mission of usefully harnessing fusion energy, but nonetheless explains to the layman the difference between fusion and fission in weapons, which should help the readers understand the differences as sources of peaceful energy as well, since this popular confusion remains a problem when proposing fusion with the `nuclear' label. Chapter 7 returns to energy sources with laser fusion, or inertial confinement fusion, which constitutes both military and civil research, depending on the country. The chapter provides a broad overview of the progress right up to today's hopes for fast ignition. The difficulty of harnessing fusion energy by magnetic or inertial confinement has created a breeding ground for what the authors call `false

  15. SAR Data Fusion Imaging Method Oriented to Target Feature Extraction

    Directory of Open Access Journals (Sweden)

    Yang Wei

    2015-02-01

    Full Text Available To deal with the difficulty for target outlines extracting precisely due to neglect of target scattering characteristic variation during the processing of high-resolution space-borne SAR data, a novel fusion imaging method is proposed oriented to target feature extraction. Firstly, several important aspects that affect target feature extraction and SAR image quality are analyzed, including curved orbit, stop-and-go approximation, atmospheric delay, and high-order residual phase error. Furthermore, the corresponding compensation methods are addressed as well. Based on the analysis, the mathematical model of SAR echo combined with target space-time spectrum is established for explaining the space-time-frequency change rule of target scattering characteristic. Moreover, a fusion imaging strategy and method under high-resolution and ultra-large observation angle range conditions are put forward to improve SAR quality by fusion processing in range-doppler and image domain. Finally, simulations based on typical military targets are used to verify the effectiveness of the fusion imaging method.

  16. Structural materials for fission & fusion energy

    Directory of Open Access Journals (Sweden)

    Steven J. Zinkle

    2009-11-01

    Full Text Available Structural materials represent the key for containment of nuclear fuel and fission products as well as reliable and thermodynamically efficient production of electrical energy from nuclear reactors. Similarly, high-performance structural materials will be critical for the future success of proposed fusion energy reactors, which will subject the structures to unprecedented fluxes of high-energy neutrons along with intense thermomechanical stresses. Advanced materials can enable improved reactor performance via increased safety margins and design flexibility, in particular by providing increased strength, thermal creep resistance and superior corrosion and neutron radiation damage resistance. In many cases, a key strategy for designing high-performance radiation-resistant materials is based on the introduction of a high, uniform density of nanoscale particles that simultaneously provide good high temperature strength and neutron radiation damage resistance.

  17. Adiabatic heavy-ion fusion potentials for fusion at deep sub-barrier energies

    Indian Academy of Sciences (India)

    S V S Sastry; S Kailas; A K Mohanty; A Saxena

    2005-01-01

    The recently reported unusual behaviour of fusion cross-sections at extreme sub-barrier energies has been examined. The adiabatic limit of fusion barriers has been determined from experimental data using the barrier penetration model. These adiabatic barriers are consistent with the adiabatic fusion barriers derived from the modified Wilzynska–Wilzynski prescription. The fusion barrier systematics has been obtained for a wide range of heavy-ion systems.

  18. Fusion

    CERN Document Server

    Mahaffey, James A

    2012-01-01

    As energy problems of the world grow, work toward fusion power continues at a greater pace than ever before. The topic of fusion is one that is often met with the most recognition and interest in the nuclear power arena. Written in clear and jargon-free prose, Fusion explores the big bang of creation to the blackout death of worn-out stars. A brief history of fusion research, beginning with the first tentative theories in the early 20th century, is also discussed, as well as the race for fusion power. This brand-new, full-color resource examines the various programs currently being funded or p

  19. Enhancement of fusion at near and sub-barrier energies for neutron-rich light nuclei

    CERN Document Server

    Singh, Varinderjit; Steinbach, T K; Wiggins, B B; Hudan, S; Lin, R T deSouza Zidu; Horowitz, C J; Baby, L T; Kuvin, S A; Tripathi, Vandana; Wiedenhover, I

    2016-01-01

    Measurement of the fusion cross-section for neutron-rich light nuclei is crucial in ascertaining if fusion of these nuclei occurs in the outer crust of a neutron star. We have therefore measured the fusion excitation function at near-barrier energies for the 19O + 12C system and compared the experimental results with the fusion excitation function of 18O + 12C and 16O + 12C. In the experiment a beam of 19O, produced via the 18O(d,p) reaction, was incident on a 12C target at energies near the Coulomb barrier. Evaporation residues produced in fusion of 18,19O ions with 12C target nuclei were detected with good geometric efficiency and identified by measuring their energy and time-of-flight. A significant enhancement in the fusion probability of 19O ions with a 12C target as compared to 18O ions is observed. The significantly larger cross-sections observed at near barrier energies are not predicted by a static model of fusion for 19O + 12C indicating that dynamics play an important role in the fusion of neutron-...

  20. Heavy Ion Inertial Fusion Energy: Summaries of Program Elements

    Energy Technology Data Exchange (ETDEWEB)

    Friedman, A; Barnard, J J; Kaganovich, I; Seidl, P A; Briggs, R J; Faltens, A; Kwan, J W; Lee, E P; Logan, B G

    2011-02-28

    The goal of the Heavy Ion Fusion (HIF) Program is to apply high-current accelerator technology to IFE power production. Ion beams of mass {approx}100 amu and kinetic energy {>=} 1 GeV provide efficient energy coupling into matter, and HIF enjoys R&D-supported favorable attributes of: (1) the driver, projected to be robust and efficient; see 'Heavy Ion Accelerator Drivers.'; (2) the targets, which span a continuum from full direct to full indirect drive (and perhaps fast ignition), and have metal exteriors that enable injection at {approx}10 Hz; see 'IFE Target Designs'; (3) the near-classical ion energy deposition in the targets; see 'Beam-Plasma Interactions'; (4) the magnetic final lens, robust against damage; see 'Final Optics-Heavy Ion Beams'; and (5) the fusion chamber, which may use neutronically-thick liquids; see 'Liquid-Wall Chambers.' Most studies of HIF power plants have assumed indirect drive and thick liquid wall protection, but other options are possible.

  1. Quantify Plasma Response to Non-Axisymmetric (3D) Magnetic Fields in Tokamaks, Final Report for FES (Fusion Energy Sciences) FY2014 Joint Research Target

    Energy Technology Data Exchange (ETDEWEB)

    Strait, E. J. [General Atomics, San Diego, CA (United States); Park, J. -K. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Marmar, E. S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Ahn, J. -W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Berkery, J. W. [Columbia Univ., New York, NY (United States); Burrell, K. H. [General Atomics, San Diego, CA (United States); Canik, J. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Delgado-Aparicio, L. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Ferraro, N. M. [General Atomics, San Diego, CA (United States); Garofalo, A. M. [General Atomics, San Diego, CA (United States); Gates, D. A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Greenwald, M. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Kim, K. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); King, J. D. [General Atomics, San Diego, CA (United States); Lanctot, M. J. [General Atomics, San Diego, CA (United States); Lazerson, S. A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Liu, Y. Q. [Culham Science Centre, Abingdon (United Kingdom). Euratom/CCFE Association; Logan, N. C. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Lore, J. D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Menard, J. E. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Nazikian, R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Shafer, M. W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Paz-Soldan, C. [General Atomics, San Diego, CA (United States); Reiman, A. H. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Rice, J. E. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Sabbagh, S. A. [Columbia Univ., New York, NY (United States); Sugiyama, L. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Turnbull, A. D. [General Atomics, San Diego, CA (United States); Volpe, F. [Columbia Univ., New York, NY (United States); Wang, Z. R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Wolfe, S. M. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2014-09-30

    The goal of the 2014 Joint Research Target (JRT) has been to conduct experiments and analysis to investigate and quantify the response of tokamak plasmas to non-axisymmetric (3D) magnetic fields. Although tokamaks are conceptually axisymmetric devices, small asymmetries often result from inaccuracies in the manufacture and assembly of the magnet coils, or from nearby magnetized objects. In addition, non-axisymmetric fields may be deliberately applied for various purposes. Even at small amplitudes of order 10-4 of the main axisymmetric field, such “3D” fields can have profound impacts on the plasma performance. The effects are often detrimental (reduction of stabilizing plasma rotation, degradation of energy confinement, localized heat flux to the divertor, or excitation of instabilities) but may in some case be beneficial (maintenance of rotation, or suppression of instabilities). In general, the magnetic response of the plasma alters the 3D field, so that the magnetic field configuration within the plasma is not simply the sum of the external 3D field and the original axisymmetric field. Typically the plasma response consists of a mixture of local screening of the external field by currents induced at resonant surfaces in the plasma, and amplification of the external field by stable kink modes. Thus, validated magnetohydrodynamic (MHD) models of the plasma response to 3D fields are crucial to the interpretation of existing experiments and the prediction of plasma performance in future devices. The non-axisymmetric coil sets available at each facility allow well-controlled studies of the response to external 3D fields. The work performed in support of the 2014 Joint Research Target has included joint modeling and analysis of existing experimental data, and collaboration on new experiments designed to address the goals of the JRT. A major focus of the work was validation of numerical models through quantitative comparison to experimental data, in

  2. Quantify Plasma Response to Non-Axisymmetric (3D) Magnetic Fields in Tokamaks, Final Report for FES (Fusion Energy Sciences) FY2014 Joint Research Target

    Energy Technology Data Exchange (ETDEWEB)

    Strait, E. J. [General Atomics, San Diego, CA (United States); Park, J. -K. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Marmar, E. S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Ahn, J. -W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Berkery, J. W. [Columbia Univ., New York, NY (United States); Burrell, K. H. [General Atomics, San Diego, CA (United States); Canik, J. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Delgado-Aparicio, L. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Ferraro, N. M. [General Atomics, San Diego, CA (United States); Garofalo, A. M. [General Atomics, San Diego, CA (United States); Gates, D. A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Greenwald, M. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Kim, K. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); King, J. D. [General Atomics, San Diego, CA (United States); Lanctot, M. J. [General Atomics, San Diego, CA (United States); Lazerson, S. A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Liu, Y. Q. [Culham Science Centre, Abingdon (United Kingdom). Euratom/CCFE Association; Logan, N. C. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Lore, J. D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Menard, J. E. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Nazikian, R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Shafer, M. W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Paz-Soldan, C. [General Atomics, San Diego, CA (United States); Reiman, A. H. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Rice, J. E. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Sabbagh, S. A. [Columbia Univ., New York, NY (United States); Sugiyama, L. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Turnbull, A. D. [General Atomics, San Diego, CA (United States); Volpe, F. [Columbia Univ., New York, NY (United States); Wang, Z. R. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Wolfe, S. M. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2014-09-30

    The goal of the 2014 Joint Research Target (JRT) has been to conduct experiments and analysis to investigate and quantify the response of tokamak plasmas to non-axisymmetric (3D) magnetic fields. Although tokamaks are conceptually axisymmetric devices, small asymmetries often result from inaccuracies in the manufacture and assembly of the magnet coils, or from nearby magnetized objects. In addition, non-axisymmetric fields may be deliberately applied for various purposes. Even at small amplitudes of order 10-4 of the main axisymmetric field, such “3D” fields can have profound impacts on the plasma performance. The effects are often detrimental (reduction of stabilizing plasma rotation, degradation of energy confinement, localized heat flux to the divertor, or excitation of instabilities) but may in some case be beneficial (maintenance of rotation, or suppression of instabilities). In general, the magnetic response of the plasma alters the 3D field, so that the magnetic field configuration within the plasma is not simply the sum of the external 3D field and the original axisymmetric field. Typically the plasma response consists of a mixture of local screening of the external field by currents induced at resonant surfaces in the plasma, and amplification of the external field by stable kink modes. Thus, validated magnetohydrodynamic (MHD) models of the plasma response to 3D fields are crucial to the interpretation of existing experiments and the prediction of plasma performance in future devices. The non-axisymmetric coil sets available at each facility allow well-controlled studies of the response to external 3D fields. The work performed in support of the 2014 Joint Research Target has included joint modeling and analysis of existing experimental data, and collaboration on new experiments designed to address the goals of the JRT. A major focus of the work was validation of numerical models through quantitative comparison to experimental data, in

  3. The role of the National Ignition Facility in the development of inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Logan, B.G.

    1996-06-01

    The authors have completed a conceptual design for a 1.8-MJ, 500-TW, 0.35-{mu}m solid-state laser system for the National Ignition Facility (NIF), which will demonstrate inertial fusion ignition and gain for national security, energy, and science applications. The technical goal of the U.S. Inertial Confinement Fusion (ICF) Program as stated in the current ICF Five-Year Program Plan is {open_quotes}to produce pure fusion ignition and burn in the laboratory, with fusion yields of 200 to 1000 MJ, in support of three missions: (1) to play an essential role in accessing physics regimes of interest in nuclear weapon design...; (2) to provide an above-ground simulation capability for nuclear weapon effects...; and (3) to develop inertial fusion energy for civilian power production.{close_quotes} This article addresses the third goal-- the development of inertial fusion energy (IFE). This article reports a variety of potential contributions the NIF could make to the development of IFE, drawn from a nationally attended workshop held at the University of California at Berkeley in Feb, 1994. In addition to demonstrating fusion ignition as a fundamental basis for IFE, the findings of the workshop, are that the NIF could also provide important data for target physics and fabrication technology, for IFE target chamber phenomena such as materials responses to target emissions, and for fusion power technology-relevant tests.

  4. Fusion Energy from the electric utilities perspective: Fusion Innovation Industry Forum

    Energy Technology Data Exchange (ETDEWEB)

    Tagle, J. A.; Felipe, A.; Gomez, A.; Sanchez-Mayoral, M. L.; Merino, A.

    2013-07-01

    The paper presents the different future energy scenarios envisaged and the so called Power Generation Fleet Transition in which Fusion Energy could play an important role. A review of the R and D and Innovation main drivers in the electric sector is outline, with a detail description of the main issues and strategic challenges in the medium and short term. The worldwide historical involvement of electric utilities in Fusion is presented and revised under the new USA Utilities technical assessment carried out by the Electric Power Research Institute EPRI. The paper also presents the work done in the last few years by the European Fusion Industry Innovation Forum FIIF-MB in order to to evaluate a wide range of fusion concepts from the utility standpoint, to enhance utilities perspective on fusion, to provide guidance to Government Bodies and national Energy strategies for fusion-utilities and finally to establish a basis for communication and cooperation in fusion for utilities standpoint. Finally the paper comments the utilities challenges pointed out by the Fusion electricity: a road map to the realization of fusion energy report issued this year by the European Fusion Development Agreement EFDA.

  5. Design, fabrication and measurement of a novel cooling arm for fusion energy source

    CERN Document Server

    Jiang, Shui-Dong; Mei, Jia-Bin; Yang, Bin; Yang, Chun-Sheng

    2012-01-01

    The issues of energy and environment are the main constraint of sustainable development in worldwide. Nuclear energy source is one important optional choice for long term sustainable development. The nuclear energy consists of fusion energy and fission energy. Compared with fission, inertial confinement fusion (ICF) is a kind of clean fusion energy and can generate large energy and little environmental pollution. ICF mainly consists of peripheral driver unit and target. The cooling arm is an important component of the target, which cools the hohlraum to maintain the required temperature and positions the thermal-mechanical package (TMP) assembly. This paper mainly investigates the cooling arm, including the structural design, the verticality of sidewall and the mechanical properties. The TMP assembly is uniformly clamped in its radial when using (111) crystal orientation silicon to fabricate cooling arm. The finite element method is used to design the structure of cooling arm with 16 clamping arms, and the ME...

  6. Fusion-fission energy systems evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Teofilo, V.L.; Aase, D.T.; Bickford, W.E.

    1980-01-01

    This report serves as the basis for comparing the fusion-fission (hybrid) energy system concept with other advanced technology fissile fuel breeding concepts evaluated in the Nonproliferation Alternative Systems Assessment Program (NASAP). As such, much of the information and data provided herein is in a form that meets the NASAP data requirements. Since the hybrid concept has not been studied as extensively as many of the other fission concepts being examined in NASAP, the provided data and information are sparse relative to these more developed concepts. Nevertheless, this report is intended to provide a perspective on hybrids and to summarize the findings of the rather limited analyses made to date on this concept.

  7. Cryogenic hydrogen fuel for controlled inertial confinement fusion (formation of reactor-scale cryogenic targets)

    Science.gov (United States)

    Aleksandrova, I. V.; Koresheva, E. R.; Krokhin, O. N.; Osipov, I. E.

    2016-12-01

    In inertial fusion energy research, considerable attention has recently been focused on low-cost fabrication of a large number of targets by developing a specialized layering module of repeatable operation. The targets must be free-standing, or unmounted. Therefore, the development of a target factory for inertial confinement fusion (ICF) is based on methods that can ensure a cost-effective target production with high repeatability. Minimization of the amount of tritium (i.e., minimization of time and space at all production stages) is a necessary condition as well. Additionally, the cryogenic hydrogen fuel inside the targets must have a structure (ultrafine layers—the grain size should be scaled back to the nanometer range) that supports the fuel layer survivability under target injection and transport through the reactor chamber. To meet the above requirements, significant progress has been made at the Lebedev Physical Institute (LPI) in the technology developed on the basis of rapid fuel layering inside moving free-standing targets (FST), also referred to as the FST layering method. Owing to the research carried out at LPI, unique experience has been gained in the development of the FST-layering module for target fabrication with an ultrafine fuel layer, including a reactor- scale target design. This experience can be used for the development of the next-generation FST-layering module for construction of a prototype of a target factory for power laser facilities and inertial fusion power plants.

  8. Cryogenic hydrogen fuel for controlled inertial confinement fusion (formation of reactor-scale cryogenic targets)

    Energy Technology Data Exchange (ETDEWEB)

    Aleksandrova, I. V.; Koresheva, E. R., E-mail: elena.koresheva@gmail.com; Krokhin, O. N. [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation); Osipov, I. E. [Power Efficiency Centre, Inter RAO UES (Russian Federation)

    2016-12-15

    In inertial fusion energy research, considerable attention has recently been focused on low-cost fabrication of a large number of targets by developing a specialized layering module of repeatable operation. The targets must be free-standing, or unmounted. Therefore, the development of a target factory for inertial confinement fusion (ICF) is based on methods that can ensure a cost-effective target production with high repeatability. Minimization of the amount of tritium (i.e., minimization of time and space at all production stages) is a necessary condition as well. Additionally, the cryogenic hydrogen fuel inside the targets must have a structure (ultrafine layers—the grain size should be scaled back to the nanometer range) that supports the fuel layer survivability under target injection and transport through the reactor chamber. To meet the above requirements, significant progress has been made at the Lebedev Physical Institute (LPI) in the technology developed on the basis of rapid fuel layering inside moving free-standing targets (FST), also referred to as the FST layering method. Owing to the research carried out at LPI, unique experience has been gained in the development of the FST-layering module for target fabrication with an ultrafine fuel layer, including a reactor- scale target design. This experience can be used for the development of the next-generation FST-layering module for construction of a prototype of a target factory for power laser facilities and inertial fusion power plants.

  9. FY-2015 FES (Fusion and Energy Sciences) Joint Research Target: Final Report for the Period October 1st, 2014, through September 30th, 2015

    Energy Technology Data Exchange (ETDEWEB)

    Podesta, M. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Holcomb, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wallace, G. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States). Plasma Science and Fusion Center; Gerhardt, S. P. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Scott, S. D. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Solomon, W. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States)

    2015-09-30

    Annual JRT-15 Target: Conduct experiments and analysis to quantify the impact of broadened current and pressure profiles on tokamak plasma confinement and stability. Broadened pressure profiles generally improve global stability but can also affect transport and confinement, while broadened current profiles can have both beneficial and adverse impacts on confinement and stability. This research will examine a variety of heating and current drive techniques in order to validate theoretical models of both the actuator performance and the transport and global stability response to varied heating and current drive deposition.

  10. Investigation of the influence of incomplete fusion on complete fusion of 16O induced reactions at moderate excitation energies

    Directory of Open Access Journals (Sweden)

    Ahamad Tauseef

    2012-12-01

    Full Text Available An attempt has been made to investigate for the reaction dynamics leading to incomplete fusion (ICF of heavy ions at moderate excitation energies, especially the influence of incomplete fusion on complete fusion (CF of 16O induced reactions at specific energies. Excitation functions (EFs of various reaction products populated via CF and/or ICF of 16O projectile with 45Sc target were measured at energies ≈3-7 MeV/nucleon, using recoil catcher technique followed by offline γ-ray spectroscopy. The measured EFs were compared with theoretical values obtained using the statistical model code PACE4. The experimentally measured EFs were in general found to be in good agreement with the theoretical predictions for non α-emitting channels in the present target projectile system. However, for α-emitting channels the measured EFs were higher than the predictions of the theoretical model codes, which may be credited to incomplete fusion reactions at these energies.

  11. Adiabatic Heavy Ion Fusion Potentials for Fusion at Deep Sub-barrier Energies

    CERN Document Server

    Sastry, S V S; Mohanty, A K; Saxena, A

    2003-01-01

    The fusion cross sections from well above barrier to extreme sub-barrier energies have been analysed using the energy (E) and angular momentum (L) dependent barrier penetration model ({\\small{ELDBPM}}). From this analysis, the adiabatic limits of fusion barriers have been determined for a wide range of heavy ion systems. The empirical prescription of Wilzynska and Wilzynski has been used with modified radius parameter and surface tension coefficient values consistent with the parameterization of the nuclear masses. The adiabatic fusion barriers calculated from this prescription are in good agreement with the adiabatic barriers deduced from {\\small{ELDBPM}} fits to fusion data. The nuclear potential diffuseness is larger at adiabatic limit, resulting in a lower $\\hbar\\omega$ leading to increase of "logarithmic slope" observed at energies well below the barrier. The effective fusion barrier radius and curvature values are anomalously smaller than the predictions of known empirical prescriptions. A detailed comp...

  12. Review of the Fusion Theory and Computing Program. Fusion Energy Sciences Advisory Committee (FESAC)

    Energy Technology Data Exchange (ETDEWEB)

    Antonsen, Thomas M. [Univ. of Maryland, College Park, MD (United States); Berry, Lee A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, Michael R. [Swarthmore College, PA (United States); Dahlburg, Jill P. [General Atomics, San Diego, CA (United States); Davidson, Ronald C. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Greenwald, Martin [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hegna, Chris C. [Univ. of Wisconsin, Madison, WI (United States); McCurdy, William [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Newman, David E. [Univ. of Alaska, Fairbanks, AK (United States); Pellegrini, Claudio [Univ. of California, Los Angeles, CA (United States); Phillips, Cynthia K. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Post, Douglass E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rosenbluth, Marshall N. [Univ. of California, San Diego, CA (United States); Sheffield, John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Simonen, Thomas C. [Munising, MI (United States); Van Dam, James [Univ. of Texas, Austin, TX (United States)

    2001-08-01

    At the November 14-15, 2000, meeting of the Fusion Energy Sciences Advisory Committee, a Panel was set up to address questions about the Theory and Computing program, posed in a charge from the Office of Fusion Energy Sciences (see Appendix A). This area was of theory and computing/simulations had been considered in the FESAC Knoxville meeting of 1999 and in the deliberations of the Integrated Program Planning Activity (IPPA) in 2000. A National Research Council committee provided a detailed review of the scientific quality of the fusion energy sciences program, including theory and computing, in 2000.

  13. LIFE: The Case for Early Commercialization of Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Anklam, T; Simon, A J; Powers, S; Meier, W R

    2010-11-30

    This paper presents the case for early commercialization of laser inertial fusion energy (LIFE). Results taken from systems modeling of the US electrical generating enterprise quantify the benefits of fusion energy in terms of carbon emission, nuclear waste and plutonium production avoidance. Sensitivity of benefits-gained to timing of market-entry is presented. These results show the importance of achieving market entry in the 2030 time frame. Economic modeling results show that fusion energy can be competitive with other low-carbon energy sources. The paper concludes with a description of the LIFE commercialization path. It proposes constructing a demonstration facility capable of continuous fusion operations within 10 to 15 years. This facility will qualify the processes and materials needed for a commercial fusion power plant.

  14. Target Recognition Based on Fuzzy Dempster Data Fusion Method

    Directory of Open Access Journals (Sweden)

    Yong Deng

    2010-08-01

    Full Text Available Data fusion technology is widely used in automatic target recognition system. Problems in data fusion system are complex by nature and can often be characterised by not only randomness but also by fuzziness. To accommodate complex natural problems with both types of uncertainties, it is profitable to construct a data fusion structure based on fuzzy set theory and Dempster Shafer evidence theory. In this paper, after representing both, the individual attribute of target in the model database and the sensor observation or report as fuzzy membership function, a likelihood function was constructed to deal with fuzzy data collected by each sensor. The method to determine basic probability assignments of each sensor report is proposed. Sensor reports are fused through classical Dempster combination rule. A numerical example is illustrated to show the target recognition application of the fuzzy-Dempster approach.Defence Science Journal, 2010, 60(5, pp.525-530, DOI:http://dx.doi.org/10.14429/dsj.60.576

  15. Systematics for low energy incomplete fusion: Still a puzzle?

    Directory of Open Access Journals (Sweden)

    Yadav Abhishek

    2016-01-01

    Full Text Available In order to have a better and clear picture of incomplete fusion reactions at energies ≈4-7MeV/nucleon, the excitation function measurements have been performed for 18O+159Tb system. The experimental data have been analyzed within the framework of compound nucleus decay. The cross-section for xn/pxn-channels are found to be well reproduced by PACE4 predictions, which suggest their production via complete fusion process. However, a significant enhancement in the excitation functions of α-emitting channels has been observed over the theoretical ones, which has been attributed due to the incomplete fusion processes. The incomplete fusion fractions have been deduced at each studied energy and compared with other nearby systems for better insight into the underlying dynamics. The incomplete fusion fraction has been found to be sensitive to the projectile’s energy and α-Q-value.

  16. Integrated inertial fusion energy chamber dynamics and response

    Energy Technology Data Exchange (ETDEWEB)

    Uddin, Hasib, E-mail: uddin3@illinois.edu [Department of Mechanical Science and Engineering, University of Illinois at Urbana–Champaign, Urbana, IL 61801 (United States); Kramer, Richard; Pantano, Carlos [Department of Mechanical Science and Engineering, University of Illinois at Urbana–Champaign, Urbana, IL 61801 (United States); Kramer, Kevin; Tang, Vincent [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Sacks, Ryan; Moses, Gregory [Fusion Technology Institute, University of Wisconsin Madison, Madison, WI 53706 (United States); Hunt, Ryan; DeMuth, James; Scott, Howard; Dunne, A. Mike [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States)

    2014-12-15

    Highlights: • LES with embedded geometry. • Repetitive IFE chamber state. • Sensitivity to blast modeling. - Abstract: This paper presents results of three-dimensional hydrodynamics simulations of the flow inside a model inertial fusion energy (IFE) fusion chamber. Turbulence modeling employing the large-eddy simulation approach is used to estimate the gas dynamics, state, and mixing after a sufficiently large number of target ignitions. The rich radiation-flow physics that takes place immediately after the lasers hit the hohlraum is modeled separately using a high-fidelity one-dimensional model, which provides reference conditions for the complex geometry three-dimensional turbulence simulations. The IFE geometry includes optical ports and recirculation openings as well as a duct to evacuate the debris produced after each energy deposition (as a model of a laser shot). Furthermore, a selected set of sensitivity studies are conducted to estimate the effect of uncertainty in radiative properties of the Xenon gas at the prevalent conditions in the chamber. The results provide guidance regarding the turbulence conditions in the chamber, which seem to have entered a decay state immediately before a new shot takes place. Computational estimates of the density variability within the chamber as well as pressure history at the approximate location of the laser optical ports is presented among other turbulence statistics.

  17. Laser Intertial Fusion Energy: Neutronic Design Aspects of a Hybrid Fusion-Fission Nuclear Energy System

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Kevin James [Univ. of California, Berkeley, CA (United States)

    2010-04-08

    This study investigates the neutronics design aspects of a hybrid fusion-fission energy system called the Laser Fusion-Fission Hybrid (LFFH). A LFFH combines current Laser Inertial Confinement fusion technology with that of advanced fission reactor technology to produce a system that eliminates many of the negative aspects of pure fusion or pure fission systems. When examining the LFFH energy mission, a significant portion of the United States and world energy production could be supplied by LFFH plants. The LFFH engine described utilizes a central fusion chamber surrounded by multiple layers of multiplying and moderating media. These layers, or blankets, include coolant plenums, a beryllium (Be) multiplier layer, a fertile fission blanket and a graphite-pebble reflector. Each layer is separated by perforated oxide dispersion strengthened (ODS) ferritic steel walls. The central fusion chamber is surrounded by an ODS ferritic steel first wall. The first wall is coated with 250-500 μm of tungsten to mitigate x-ray damage. The first wall is cooled by Li17Pb83 eutectic, chosen for its neutron multiplication and good heat transfer properties. The Li17Pb83 flows in a jacket around the first wall to an extraction plenum. The main coolant injection plenum is immediately behind the Li17Pb83, separated from the Li17Pb83 by a solid ODS wall. This main system coolant is the molten salt flibe (2LiF-BeF2), chosen for beneficial neutronics and heat transfer properties. The use of flibe enables both fusion fuel production (tritium) and neutron moderation and multiplication for the fission blanket. A Be pebble (1 cm diameter) multiplier layer surrounds the coolant injection plenum and the coolant flows radially through perforated walls across the bed. Outside the Be layer, a fission fuel layer comprised of depleted uranium contained in Tristructural-isotropic (TRISO) fuel particles

  18. Spiraling Beam Illumination Uniformity on Heavy Ion Fusion Target

    OpenAIRE

    Kurosaki, T; Kawata, S.; Noguchi, K.; Koseki, S; Barada, D.; Ma, Y. Y.; Ogoyski, A. I.; Barnard, J. J.; Logan, B. G.

    2012-01-01

    A few percent wobbling-beam illumination nonuniformity is realized in heavy ion inertial confinement fusion (HIF) by a spiraling beam axis motion in the paper. So far the wobbling heavy ion beam (HIB) illumination was proposed to realize a uniform implosion in HIF. However, the initial imprint of the wobbling HIBs was a serious problem and introduces a large unacceptable energy deposition nonuniformity. In the wobbling HIBs illumination, the illumination nonuniformity oscillates in time and s...

  19. Hypervelocity Impact Fusion with Compressed Deuterium-Tritium Targets

    OpenAIRE

    Olariu, Silviu

    1998-01-01

    The neutron yields observed in inertial confinement fusion experiments for higher convergence ratios are about two orders of magnitude smaller than the neutron yields predicted by one-dimensional models, the discrepancy being attributed to the development of instabilities. We consider the possibility that ignition and a moderate gain could be achieved with existing laser facilities if the laser driver energy is used to produce only the radial compression of the fuel capsule to high densities ...

  20. Implementing agreement on a co-operative program on inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J; Hogan, W; Meier, W

    2000-01-04

    The Programme to be carried out by the Contracting Parties within the framework of this Agreement shall consist of co-operative research, development, demonstrations and exchanges of information regarding inertial fusion energy (IFE). This shall include: (1) Nuclear Technology, (2) Fusion Materials, (3) Environment, Safety and Economics, (4) Laser Drivers, (5) Ion Beam Drivers and Beam/Plasma Interactions, (6) Target Production, Injection and Tracking, (7) Fusion Diagnostics, (8) Driver/Plasma Interactions, (9) Fast Ignition and (10) Power Plant Design Studies. Annexes to this agreement will describe specific tasks in each area.

  1. Magnetized Target Fusion Propulsion: Plasma Injectors for MTF Guns

    Science.gov (United States)

    Griffin, Steven T.

    2003-01-01

    To achieve increased payload size and decreased trip time for interplanetary travel, a low mass, high specific impulse, high thrust propulsion system is required. This suggests the need for research into fusion as a source of power and high temperature plasma. The plasma would be deflected by magnetic fields to provide thrust. Magnetized Target Fusion (MTF) research consists of several related investigations into these topics. These include the orientation and timing of the plasma guns and the convergence and interface development of the "pusher" plasma. Computer simulations of the gun as it relates to plasma initiation and repeatability are under investigation. One of the items under development is the plasma injector. This is a surface breakdown driven plasma generator designed to function at very low pressures. The performance, operating conditions and limitations of these injectors need to be determined.

  2. Fusion energy science: Clean, safe, and abundant energy through innovative science and technology

    Energy Technology Data Exchange (ETDEWEB)

    None

    2001-01-01

    Fusion energy science combines the study of the behavior of plasmas--the state of matter that forms 99% of the visible universe--with a vision of using fusion--the energy source of the stars--to create an affordable, plentiful, and environmentally benign energy source for humankind. The dual nature of fusion energy science provides an unfolding panorama of exciting intellectual challenge and a promise of an attractive energy source for generations to come. The goal of this report is a comprehensive understanding of plasma behavior leading to an affordable and attractive fusion energy source.

  3. NIFS contributions to 19th IAEA fusion energy conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-11-01

    NIFS has presented 21 papers at the 19th IAEA Fusion Energy Conference (Lyon, France, 14-19 October 2002). The contributed papers are collected in this report. The 21 papers are indexed individually. (J.P.N.)

  4. Nuclear fusion and its large potential for the future world energy supply

    Directory of Open Access Journals (Sweden)

    Ongena Jef

    2016-12-01

    Full Text Available An overview of the energy problem in the world is presented. The colossal task of ‘decarbonizing’ the current energy system, with ~85% of the primary energy produced from fossil sources is discussed. There are at the moment only two options that can contribute to a solution: renewable energy (sun, wind, hydro, etc. or nuclear fission. Their contributions, ~2% for sun and wind, ~6% for hydro and ~5% for fission, will need to be enormously increased in a relatively short time, to meet the targets set by policy makers. The possible role and large potential for fusion to contribute to a solution in the future as a safe, nearly inexhaustible and environmentally compatible energy source is discussed. The principles of magnetic and inertial confinement are outlined, and the two main options for magnetic confinement, tokamak and stellarator, are explained. The status of magnetic fusion is summarized and the next steps in fusion research, ITER and DEMO, briefly presented.

  5. Excitation Functions of Fusion and Fission for 32S+170Er at Energies Near and Below Coulomb Barrier

    Institute of Scientific and Technical Information of China (English)

    BAO; Peng-fei; LIN; Cheng-jian; YANG; Feng; JIA; Hui-ming; XU; Xin-xing; YANG; Lei; SUN; Li-jie; MA; Nan-ru; ZHANG; Huan-qiao; LIU; Zu-hua

    2013-01-01

    Excitation functions of fusion evaporation residue(ER)and fission for 32S+170Er system at near barrier energy region were measured,respectively.With the comparison to the calculations of coupledchannels effects,it is accessible to investigate the impacts on the fusion and fission processes of target deformation and the dependence on the entrance-channel.The experiment was performed at Beijing HI-13 Tandem Accelerator.Fission and fusion evaporation

  6. Towards fusion energy as a sustainable energy source: Activities at DTU Physics

    DEFF Research Database (Denmark)

    Rasmussen, Jesper; Christensen, Alexander Simon; Dam, Magnus

    2014-01-01

    Nuclear fusion – the process from which the Sun derives its energy – holds the potential to become a clean,safe, highly efficient, and virtually inexhaustible energy source for the future. To mimic this process on earth, experimental fusion devices seek to heat gas to millions of degrees (creating...... a fusion plasma) and to confine it within magnetic fields. Learning how such plasmas behave and can be controlled is a crucial step towards realizing fusion as a sustainable energy source.At the Plasma Physics and Fusion Energy (PPFE) section at DTU Physics, we are exploring these issues,focusing on areas...... of high priority on the way towards a working fusion power plant. On the theoreticalfront, we are simulating plasma turbulence and transport of heat and particles in fusion plasmas (Fig. 1a). These issues play a key role in determining how the plasma behaves globally and how well it remains confined...

  7. Understanding and accepting fusion as an alternative energy source

    Energy Technology Data Exchange (ETDEWEB)

    Goerz, D.A.

    1987-12-10

    Fusion, the process that powers our sun, has long promised to be a virtually inexhaustible source of energy for mankind. No other alternative energy source holds such bright promise, and none has ever presentd such formidable scientific and engineering challenges. Serious research efforts have continued for over 30 years in an attempt to harness and control fusion here on earth. Scientists have made considerable progress in the last decade toward achieving the conditions required for fusion power, and recent experimental results and technological progress have made the scientific feasibility of fusion a virtual certainty. With this knowledge and confidence, the emphasis can now shift toward developing power plants that are practical and economical. Although the necessary technology is not in hand today, the extension to an energy producing system in 20 years is just as attainable as was putting a man on the moon. In the next few decades, the world's population will likely double while the demand for energy will nearly quadruple. Realistic projections show that within the next generation a significant fraction of our electric power must come from alternative energy sources. Increasing environmental concerns may further accelerate this timetable in which new energy sources must be introduced. The continued development of fusion systems to help meet the energy needs of the future will require greater public understanding and support of this technology. The fusion community must do more to make the public aware of the fact that energy is a critical international issue and that fusion is a viable and necessary energy technology that will be safe and economical. 12 refs., 8 figs.

  8. Calculation of fusion gain in fast ignition with magnetic target by relativistic electrons and protons

    Directory of Open Access Journals (Sweden)

    A Parvazian

    2010-12-01

    Full Text Available Fast ignition is a new method for inertial confinement fusion (ICF in which the compression and ignition steps are separated. In the first stage, fuel is compressed by laser or ion beams. In the second phase, relativistic electrons are generated by pettawat laser in the fuel. Also, in the second phase 5-35 MeV protons can be generated in the fuel. Electrons or protons can penetrate in to the ultra-dense fuel and deposit their energy in the fuel . More recently, cylindrical rather than spherical fuel chambers with magnetic control in the plasma domain have been also considered. This is called magnetized target fusion (MTF. Magnetic field has effects on relativistic electrons energy deposition rate in fuel. In this work, fast ignition method in cylindrical fuel chambers is investigated and transportation of the relativistic electrons and protons is calculated using MCNPX and FLUKA codes with 0. 25 and 0. 5 tesla magnetic field in single and dual hot spot. Furthermore, the transfer rate of relativistic electrons and high energy protons to the fuel and fusion gain are calculated. The results show that the presence of external magnetic field guarantees higher fusion gain, and relativistic electrons are much more appropriate objects for ignition. MTF in dual hot spot can be considered as an appropriate substitution for the current ICF techniques.

  9. Laser Intertial Fusion Energy: Neutronic Design Aspects of a Hybrid Fusion-Fission Nuclear Energy System

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Kevin James [Univ. of California, Berkeley, CA (United States)

    2010-04-08

    This study investigates the neutronics design aspects of a hybrid fusion-fission energy system called the Laser Fusion-Fission Hybrid (LFFH). A LFFH combines current Laser Inertial Confinement fusion technology with that of advanced fission reactor technology to produce a system that eliminates many of the negative aspects of pure fusion or pure fission systems. When examining the LFFH energy mission, a significant portion of the United States and world energy production could be supplied by LFFH plants. The LFFH engine described utilizes a central fusion chamber surrounded by multiple layers of multiplying and moderating media. These layers, or blankets, include coolant plenums, a beryllium (Be) multiplier layer, a fertile fission blanket and a graphite-pebble reflector. Each layer is separated by perforated oxide dispersion strengthened (ODS) ferritic steel walls. The central fusion chamber is surrounded by an ODS ferritic steel first wall. The first wall is coated with 250-500 μm of tungsten to mitigate x-ray damage. The first wall is cooled by Li17Pb83 eutectic, chosen for its neutron multiplication and good heat transfer properties. The Li17Pb83 flows in a jacket around the first wall to an extraction plenum. The main coolant injection plenum is immediately behind the Li17Pb83, separated from the Li17Pb83 by a solid ODS wall. This main system coolant is the molten salt flibe (2LiF-BeF2), chosen for beneficial neutronics and heat transfer properties. The use of flibe enables both fusion fuel production (tritium) and neutron moderation and multiplication for the fission blanket. A Be pebble (1 cm diameter) multiplier layer surrounds the coolant injection plenum and the coolant flows radially through perforated walls across the bed. Outside the Be layer, a fission fuel layer comprised of depleted uranium contained in Tristructural-isotropic (TRISO) fuel particles

  10. Projectile - Mass asymmetry systematics for low energy incomplete fusion

    Directory of Open Access Journals (Sweden)

    Singh Pushpendra P.

    2015-01-01

    Full Text Available In the present work, low energy incomplete fusion (ICF in which only a part of projectile fuses with target nucleus has been investigated in terms of various entrance channel parameters. The ICF strength function has been extracted from the analysis of experimental excitation functions (EFs measured for different projectile-target combinations from near- to well above- barrier energies in 12C,16O(from 1.02Vb to 1.64Vb+169Tm systems. Experimental EFs have been analysed in the framework statistical model code PACE4 based on the idea of equilibrated compound nucleus decay. It has been found that the value of ICF fraction (FICF increases with incident projectile energy. A substantial fraction of ICF (FICF ≈ 7 % has been accounted even at energy as low as ≈ 7.5% above the barrier (at relative velocity νrel ≈0.027 in 12C+169Tm system, and FICF ≈ 10 % at νrel ≈0.014 in 16O+169Tm system. The probability of ICF is discussed in light of the Morgenstern’s mass-asymmetry systematics. The value of FICF for 16O+169Tm systems is found to be 18.3 % higher than that observed for 12C+169Tm systems. Present results together with the re-analysis of existing data for nearby systems conclusively demonstrate strong competition of ICF with CF even at slightly above barrier energies, and strong projectile dependence that seems to supplement the Morgenstern’s systematics.

  11. Fusion energy for space: Feasibility demonstration. A proposal to NASA

    Science.gov (United States)

    Schulze, Norman R.

    1992-01-01

    This proposed program is to initiate a space flight research and development program to develop fusion energy for the space applications of direct space propulsion and direct space power, that is, a Space Fusion Energy (SFE) program. 'Direct propulsion' refers to the use of plasma energy directly for thrust without requiring other energy conversion systems. Further, to provide space missions with large electrical power, 'direct space power' is proposed whereby the direct conversion of charged particles into electricity is used, thereby avoiding thermal conversion system losses. The energy release from nuclear fusion reactions makes these highly efficient, high power space systems possible. The program as presented conducts in an orderly, hierarchical manner the necessary planning, analyses, and testing to demonstrate the practical use of fusion energy for space. There is nothing discussed that is known to be theoretically impossible. Validation of the engineering principles is sought in this program which uses a cost-benefit approach. Upon successful program completion, space will become more accessible and space missions more safely conducted. The country will have taken a giant step toward the commercialization of space. The mission enabling capability provided by fusion energy is well beyond mission planners' current dreams.

  12. Fusion

    Science.gov (United States)

    Herman, Robin

    1990-10-01

    The book abounds with fascinating anecdotes about fusion's rocky path: the spurious claim by Argentine dictator Juan Peron in 1951 that his country had built a working fusion reactor, the rush by the United States to drop secrecy and publicize its fusion work as a propaganda offensive after the Russian success with Sputnik; the fortune Penthouse magazine publisher Bob Guccione sank into an unconventional fusion device, the skepticism that met an assertion by two University of Utah chemists in 1989 that they had created "cold fusion" in a bottle. Aimed at a general audience, the book describes the scientific basis of controlled fusion--the fusing of atomic nuclei, under conditions hotter than the sun, to release energy. Using personal recollections of scientists involved, it traces the history of this little-known international race that began during the Cold War in secret laboratories in the United States, Great Britain and the Soviet Union, and evolved into an astonishingly open collaboration between East and West.

  13. Premature Activation of the Paramyxovirus Fusion Protein before Target Cell Attachment with Corruption of the Viral Fusion Machinery*

    Science.gov (United States)

    Farzan, Shohreh F.; Palermo, Laura M.; Yokoyama, Christine C.; Orefice, Gianmarco; Fornabaio, Micaela; Sarkar, Aurijit; Kellogg, Glen E.; Greengard, Olga; Porotto, Matteo; Moscona, Anne

    2011-01-01

    Paramyxoviruses, including the childhood pathogen human parainfluenza virus type 3, enter host cells by fusion of the viral and target cell membranes. This fusion results from the concerted action of its two envelope glycoproteins, the hemagglutinin-neuraminidase (HN) and the fusion protein (F). The receptor-bound HN triggers F to undergo conformational changes that render it competent to mediate fusion of the viral and cellular membranes. We proposed that, if the fusion process could be activated prematurely before the virion reaches the target host cell, infection could be prevented. We identified a small molecule that inhibits paramyxovirus entry into target cells and prevents infection. We show here that this compound works by an interaction with HN that results in F-activation prior to receptor binding. The fusion process is thereby prematurely activated, preventing fusion of the viral membrane with target cells and precluding viral entry. This first evidence that activation of a paramyxovirus F can be specifically induced before the virus contacts its target cell suggests a new strategy with broad implications for the design of antiviral agents. PMID:21799008

  14. Study of Plasma Liner Driven Magnetized Target Fusion Via Advanced Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Samulyak, Roman V. [State Univ. of New York (SUNY), Stony Brook, NY (United States); Brookhaven National Lab. (BNL), Upton, NY (United States); Parks, Paul [General Atomics, San Diego, CA (United States)

    2013-08-31

    The feasibility of the plasma liner driven Magnetized Target Fusion (MTF) via terascale numerical simulations will be assessed. In the MTF concept, a plasma liner, formed by merging of a number (60 or more) of radial, highly supersonic plasma jets, implodes on the target in the form of two compact plasma toroids, and compresses it to conditions of the fusion ignition. By avoiding major difficulties associated with both the traditional laser driven inertial confinement fusion and solid liner driven MTF, the plasma liner driven MTF potentially provides a low-cost and fast R&D path towards the demonstration of practical fusion energy. High fidelity numerical simulations of full nonlinear models associated with the plasma liner MTF using state-of-art numerical algorithms and terascale computing are necessary in order to resolve uncertainties and provide guidance for future experiments. At Stony Brook University, we have developed unique computational capabilities that ideally suite the MTF problem. The FronTier code, developed in collaboration with BNL and LANL under DOE funding including SciDAC for the simulation of 3D multi-material hydro and MHD flows, has beenbenchmarked and used for fundamental and engineering problems in energy science applications. We have performed 3D simulations of converging supersonic plasma jets, their merger and the formation of the plasma liner, and a study of the corresponding oblique shock problem. We have studied the implosion of the plasma liner on the magnetized plasma target by resolving Rayleigh-Taylor instabilities in 2D and 3D and other relevant physics and estimate thermodynamic conditions of the target at the moment of maximum compression and the hydrodynamic efficiency of the method.

  15. Direct energy conversion for IEC fusion for space applications

    Energy Technology Data Exchange (ETDEWEB)

    Momota, Hiromu; Nadler, Jon [National Inst. for Fusion Science, Toki, Gifu (Japan); Miley, George H. [Fusion Studies Laboratory, Urbana, IL (United States)

    2000-08-01

    The paper describes a concept of extracting fusion power from D-{sup 3}He fueled IEC (Inertia Electrostatic Configuration) devices. The fusion system consists of a series of fusion modules and direct energy converters at an end or at both ends. This system of multiple units is linear and is connected by a magnetic field. A pair of coils anti-parallel to the magnetic field yields a field-null domain at the center of each unit as required for IEC operation. A stabilizing coil installed between the coil pairs eliminates the strong attractive force between the anti-parallel coils. Accessible regions for charged particle trajectories are essentially isolated from the coil structure. Thus, charged particles are directed along magnetic field lines to the direct energy converter without appreciable losses. A direct energy converter unit designed to be compatible to this unique system is also described. It basically consists of a separator and a traveling wave converter. A separator separates low energy ions and electron from the 14.7 MeV fusion protons and then converts their energy into electricity. In the traveling wave direct energy converter, fusion protons are modulated to form bunches. It couples with a transmission line to couple AC power out. The overall conversion efficiency of this system, combined with E-{sup 3}He IEC cores, is estimated as high as 60%. (author)

  16. Impact of Fast Ignition on Laser Fusion Energy Development

    Science.gov (United States)

    Mirna, Kunioki

    2016-10-01

    Reviewed are the early history of Japanese laser fusion research and the recent achievement of fast ignition research at Institute of Laser Engineering (ILE), Osaka University. After the achievement of high density compression at Osaka University, LLE of University Rochester, and LLNL, the critical issue of Inertial Fusion Energy (IFE) research became the formation of hot spark in a compressed plasma. In this lecture, the history of the fast ignition research will be reviewed and future prospects are presented.

  17. Applications of Fusion Energy Sciences Research - Scientific Discoveries and New Technologies Beyond Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, Amy [Univ. of Wisconsin, Madison, WI (United States); Callis, Richard [General Atomics, San Diego, CA (United States); Efthimion, Philip [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Foster, John [Univ. of Michigan, Ann Arbor, MI (United States); Keane, Christopher [Washington State Univ., Pullman, WA (United States); Onsager, Terry [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); O' Shea, Patrick [Univ. of Maryland, College Park, MD (United States)

    2015-09-01

    Since the 1950s, scientists and engineers in the U.S. and around the world have worked hard to make an elusive goal to be achieved on Earth: harnessing the reaction that fuels the stars, namely fusion. Practical fusion would be a source of energy that is unlimited, safe, environmentally benign, available to all nations and not dependent on climate or the whims of the weather. Significant resources, most notably from the U.S. Department of Energy (DOE) Office of Fusion Energy Sciences (FES), have been devoted to pursuing that dream, and significant progress is being made in turning it into a reality. However, that is only part of the story. The process of creating a fusion-based energy supply on Earth has led to technological and scientific achievements of far-reaching impact that touch every aspect of our lives. Those largely unanticipated advances, spanning a wide variety of fields in science and technology, are the focus of this report. There are many synergies between research in plasma physics (the study of charged particles and fluids interacting with self-consistent electric and magnetic fields), high-energy physics, and condensed matter physics dating back many decades. For instance, the formulation of a mathematical theory of solitons, solitary waves which are seen in everything from plasmas to water waves to Bose-Einstein Condensates, has led to an equal span of applications, including the fields of optics, fluid mechanics and biophysics. Another example, the development of a precise criterion for transition to chaos in Hamiltonian systems, has offered insights into a range of phenomena including planetary orbits, two-person games and changes in the weather. Seven distinct areas of fusion energy sciences were identified and reviewed which have had a recent impact on fields of science, technology and engineering not directly associated with fusion energy: Basic plasma science; Low temperature plasmas; Space and astrophysical plasmas; High energy density

  18. Applications of Fusion Energy Sciences Research - Scientific Discoveries and New Technologies Beyond Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, Amy [Univ. of Wisconsin, Madison, WI (United States); Callis, Richard [General Atomics, San Diego, CA (United States); Efthimion, Philip [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Foster, John [Univ. of Michigan, Ann Arbor, MI (United States); Keane, Christopher [Washington State Univ., Pullman, WA (United States); Onsager, Terry [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); O' Shea, Patrick [Univ. of Maryland, College Park, MD (United States)

    2015-09-01

    Since the 1950s, scientists and engineers in the U.S. and around the world have worked hard to make an elusive goal to be achieved on Earth: harnessing the reaction that fuels the stars, namely fusion. Practical fusion would be a source of energy that is unlimited, safe, environmentally benign, available to all nations and not dependent on climate or the whims of the weather. Significant resources, most notably from the U.S. Department of Energy (DOE) Office of Fusion Energy Sciences (FES), have been devoted to pursuing that dream, and significant progress is being made in turning it into a reality. However, that is only part of the story. The process of creating a fusion-based energy supply on Earth has led to technological and scientific achievements of far-reaching impact that touch every aspect of our lives. Those largely unanticipated advances, spanning a wide variety of fields in science and technology, are the focus of this report. There are many synergies between research in plasma physics, (the study of charged particles and fluids interacting with self-consistent electric and magnetic fields), high-energy physics, and condensed matter physics dating back many decades. For instance, the formulation of a mathematical theory of solitons, solitary waves which are seen in everything from plasmas to water waves to Bose-Einstein Condensates, has led to an equal span of applications, including the fields of optics, fluid mechanics and biophysics. Another example, the development of a precise criterion for transition to chaos in Hamiltonian systems, has offered insights into a range of phenomena including planetary orbits, two-person games and changes in the weather. Seven distinct areas of fusion energy sciences were identified and reviewed which have had a recent impact on fields of science, technology and engineering not directly associated with fusion energy: Basic plasma science; Low temperature plasmas; Space and astrophysical plasmas; High energy density

  19. The Role of Fusion in the Future World Energy Market

    Science.gov (United States)

    Sheffield, John

    1996-05-01

    The energy world, in which fusion energy must compete, has changed in recent years with the prospect of a 40-year supply of low-cost oil and gas. This cheap fuel represents a one-time opportunity for developing countries to raise their standards of living, and if historical trends continue, lower their rate of population growth. This brief opportunity for cheap fossil-fuel and the similar 40-year period to commercialize fusion are transients when viewed against the time scale of civilization. We need to develop and deploy the long-term energy sources, such as fusion (fission and 'renewables'), and in all cases improve energy efficiency before the fossil fuels rise in cost and a large fraction of a burgeoning world population is condemned to permanent poverty.

  20. Unexpected show up of incomplete fusion at low projectile energies

    Directory of Open Access Journals (Sweden)

    Singh B.P.

    2011-10-01

    Full Text Available In this paper, some of the important findings of recent measurements performed to study incomplete fusion at low bombarding energies (i.e., Elab ≈ 4-7 MeV/nucleon in 12C, 16O+169Tm systems are briefly summarized. The spin-distributions of xn, pxn, αxn/2αxn- channels have been measured to probe entirely different γ-emission patterns (and feeding intensity profiles during the de-excitation of complete and incomplete fusion objects. Incomplete fusion strength function has been deduced (from the analysis of experimental excitation functions in context of equilibrated compound nucleus decay to achieve information of onset and strength of incomplete fusion in terms of various entrance channel parameters. Presence of incomplete fusion at slightly above barrier energies has been confirmed by the measurement of linear momentum distribution of heavy recoils. Present results conclusively demonstrate, the existence of incomplete fusion at low bombarding energies, its strong dependence on entrance channel parameters, and the possibility to populate high spin states.

  1. Fusion Based Neutron Sources for Security Applications: Energy Optimisation

    OpenAIRE

    Albright, S.; Seviour, Rebecca

    2014-01-01

    There is a growing interest in the use of neutrons for na- tional security. The majority of work on security focuses on the use of either sealed tube DT fusors or fission sources, e.g. Cf-252. Fusion reactions enable the energy of the neu- tron beam to be chosen to suit the application, rather than the application being chosen based on the available neu- tron beam energy. In this paper we discuss simulations of fusion reactions demonstrating the broad range of energies available and methods f...

  2. Nuclear Propulsion through Direct Conversion of Fusion Energy: The Fusion Driven Rocket

    Science.gov (United States)

    Slough, John; Pancotti, Anthony; Kirtley, David; Pihl, Christopher; Pfaff, Michael

    2012-01-01

    The future of manned space exploration and development of space depends critically on the creation of a dramatically more proficient propulsion architecture for in-space transportation. A very persuasive reason for investigating the applicability of nuclear power in rockets is the vast energy density gain of nuclear fuel when compared to chemical combustion energy. Current nuclear fusion efforts have focused on the generation of electric grid power and are wholly inappropriate for space transportation as the application of a reactor based fusion-electric system creates a colossal mass and heat rejection problem for space application.

  3. Energy, material and land requirement of a fusion plant

    DEFF Research Database (Denmark)

    Schleisner, Liselotte; Hamacher, T.; Cabal, H.

    2001-01-01

    The energy and material necessary to construct a power plant and the land covered by the plant are indicators for the ‘consumption’ of environment by a certain technology. Based on current knowledge, estimations show that the material necessary to construct a fusion plant will exceed the material...... requirement of a fission plant by a factor of two. The material requirement for a fusion plant is roughly 2000 t/MW and little less than 1000 t/MW for a fission plant. The land requirement for a fusion plant is roughly 300 m2/MW and the land requirement for a fission plant is a little less than 200 m2/MW....... The energy pay back time, defined later in Section 6, is little more than half a year for a fusion plant with capacity 1 GWe. Only the electrical energy is accounted for as released energy not the thermal energy. In all these indicators, fusion compares well with conventional technologies while it consumes...

  4. Spiraling Beam Illumination Uniformity on Heavy Ion Fusion Target

    CERN Document Server

    Kurosaki, T; Noguchi, K; Koseki, S; Barada, D; Ma, Y Y; Ogoyski, A I; Barnard, J J; Logan, B G

    2012-01-01

    A few percent wobbling-beam illumination nonuniformity is realized in heavy ion inertial confinement fusion (HIF) by a spiraling beam axis motion in the paper. So far the wobbling heavy ion beam (HIB) illumination was proposed to realize a uniform implosion in HIF. However, the initial imprint of the wobbling HIBs was a serious problem and introduces a large unacceptable energy deposition nonuniformity. In the wobbling HIBs illumination, the illumination nonuniformity oscillates in time and space. The oscillating-HIB energy deposition may contribute to the reduction of the HIBs illumination nonuniformity. The wobbling HIBs can be generated in HIB accelerators and the oscillating frequency may be several 100MHz-1GHz. Three-dimensional HIBs illumination computations presented here show that the few percent wobbling HIBs illumination nonuniformity oscillates successfully with the same wobbling HIBs frequency.

  5. Prediction of off-target drug effects through data fusion.

    Science.gov (United States)

    Yera, Emmanuel R; Cleves, Ann E; Jain, Ajay N

    2014-01-01

    We present a probabilistic data fusion framework that combines multiple computational approaches for drawing relationships between drugs and targets. The approach has special relevance to identifying surprising unintended biological targets of drugs. Comparisons between molecules are made based on 2D topological structural considerations, based on 3D surface characteristics, and based on English descriptions of clinical effects. Similarity computations within each modality were transformed into probability scores. Given a new molecule along with a set of molecules sharing some biological effect, a single score based on comparison to the known set is produced, reflecting either 2D similarity, 3D similarity, clinical effects similarity or their combination. The methods were validated within acurated structural pharmacology database (SPDB) and further tested by blind application to data derived from the ChEMBL database. For prediction of off-target effects, 3D-similarity performed best as a single modality, but combining all methods produced performance gains. Striking examples of structurally surprising off-target predictions are presented.

  6. Overview of recent tritium target filling, layering, and material testing at Los Alamos national laboratory in support of inertial fusion experiments

    Energy Technology Data Exchange (ETDEWEB)

    Ebey, P. S.; Dole, J. M.; Geller, D. A.; Hoffer, J. K.; Morris, J.; Nobile, A.; Schoonover, J. R.; Wilson, D. [MS-C927, Los Alamos National Laboratory, Los Alamos, NM 87544 (United States); Bonino, M.; Harding, D.; Sangster, C.; Shmayda, W. [Laboratory for Laser Energetics LLE, Univ. of Rochester, 250 East River Road, Rochester, NY 14623 (United States); Nikroo, A.; Sheliak, J. D. [General Atomics GA (United States); Burmann, J.; Cook, B.; Letts, S.; Sanchez, J. [Lawrence Livermore National Laboratory LLNL (United States)

    2008-07-15

    The Tritium Science and Engineering (AET-3) Group at Los Alamos National Laboratory (LANL) performs a variety of activities to support Inertial Fusion (IF) research - both to further fundamental fusion science and to develop technologies in support of Inertial Fusion Energy (IFE) power generation. Inertial fusion ignition target designs have a smooth spherical shell of cryogenic Deuterium-Tritium (DT) solid contained within a metal or plastic shell that is a few mm in diameter. Fusion is attained by imploding these shells under the symmetric application of energy beams. For IFE targets the DT solid must also survive the process of injecting it into the power plant reactor. Non-ignition IF targets often require a non-cryogenic DT gas fill of a glass or polymeric shell. In this paper an overview will be given of recent LANL activities to study cryogenic DT layering, observe tritium exposure effects on IF relevant materials, and fill targets in support of IF implosion experiments. (authors)

  7. Terrorist targeting and energy security

    Energy Technology Data Exchange (ETDEWEB)

    Toft, Peter; Duero, Arash; Bieliauskas, Arunas [Institute of Energy, Joint Research Center of the European Commission, P.O. Box 2, 1755 ZG Petten (Netherlands)

    2010-08-15

    Sudden, short-term disruptions seriously endangering energy security can be triggered by a variety of events - among them attacks by terrorists. This study investigates terrorist attack practices against energy infrastructures and discusses how we may understand them. Our results indicate that attacks against energy infrastructures are comparatively few. Also, we find no strong connection between the ideologies of various terrorist groups and their proclivity to attack. In addition, the highly disproportionate number of attacks in a handful of countries highlights the strong geographic concentration of attacks. To explain these findings, we analyze terrorist targeting incentives including intimidation levels, symbolism, attack feasibility, and concerns for stakeholders. We argue that terrorists in general have comparatively few incentives to attack energy supply infrastructures based on our assessment of these factors. Moreover, higher levels of terrorist incidents in states more prone to internal violent conflict may suggest stronger incentives to attack energy infrastructures. When outlining energy security policies, the low frequency of worldwide attacks coupled with the high concentration of attacks in certain unstable countries should be taken into consideration. Energy importing countries could benefit from developing strategies to increase stability in key energy supply and/or transit countries facing risks of internal instability. (author)

  8. Simulation of the target creation through FRC merging for a magneto-inertial fusion concept

    Science.gov (United States)

    Li, Chenguang; Yang, Xianjun

    2017-04-01

    A two-dimensional magnetohydrodynamics model has been used to simulate the target creation process in a magneto-inertial fusion concept named Magnetized Plasma Fusion Reactor (MPFR) [C. Li and X. Yang, Phys. Plasmas 23, 102702 (2016)], where the target plasma created through Field reversed configuration (FRC) merging was compressed by an imploding liner driven by the pulsed-power driver. In the scheme, two initial FRCs (Field reversed configurations) are translated into the region where FRC merging occurs, bringing out the target plasma ready for compression. The simulations cover the three stages of the target creation process: formation, translation, and merging. The factors affecting the achieved target are analyzed numerically. The magnetic field gradient produced by the conical coils is found to determine how fast the FRC is accelerated to peak velocity and the collision merging occurs. Moreover, it is demonstrated that FRC merging can be realized by real coils with gaps showing nearly identical performance, and the optimized target by FRC merging shows larger internal energy and retained flux, which is more suitable for the MPFR concept.

  9. Systematic study of complete fusion suppression in reactions involving weakly bound nuclei at energies above the Coulomb barrier

    CERN Document Server

    Wang, Bing; Diaz-Torres, Alexis; Zhao, En-Guang; Zhou, Shan-Gui

    2016-01-01

    Complete fusion excitation functions of reactions involving breakup are studied by using the empirical coupled-channel (ECC) model with breakup effects considered. An exponential function with two parameters is adopted to describe the prompt-breakup probability in the ECC model. These two parameters are fixed by fitting the measured prompt-breakup probability or the complete fusion cross sections. The suppression of complete fusion at energies above the Coulomb barrier is studied by comparing the data with the predictions from the ECC model without the breakup channel considered. The results show that the suppression of complete fusion are roughly independent of the target for the reactions involving the same projectile.

  10. Hypervelocity Impact Fusion with Compressed Deuterium-Tritium Targets

    CERN Document Server

    Olariu, S

    1998-01-01

    The neutron yields observed in inertial confinement fusion experiments for higher convergence ratios are about two orders of magnitude smaller than the neutron yields predicted by one-dimensional models, the discrepancy being attributed to the development of instabilities. We consider the possibility that ignition and a moderate gain could be achieved with existing laser facilities if the laser driver energy is used to produce only the radial compression of the fuel capsule to high densities but relatively low temperatures, while the ignition of the fusion reactions in the compressed fuel capsule will be effected by a synchronized hypervelocity impact. A positively-charged incident projectile can be accelerated to velocities of 3.5 x 10^6 m/s, resulting in ignition temperatures of about 4 keV, by a conventional low-beta linac having a length of 13 km if deuterium-tritium densities of 570 g/cm^3 could be obtained by laser-driven compression.

  11. Fusion of light exotic nuclei at near-barrier energies: Effect of inelastic excitation

    Indian Academy of Sciences (India)

    P Banerjee; K Krishan; S Bhattacharya; C Bhattacharya

    2003-09-01

    The effect of inelastic excitation of exotic light projectiles (proton- as well as neutron-rich) 17F and 11Be on fusion with heavy target has been studied at near-barrier energies. The calculations have been performed in the coupled channels approach where, in addition to the normal coupling of the ground state of the projectile to the continuum, inelastic excitation of the projectile to the bound excited state and its coupling to the continuum have also been taken into consideration. The inclusion of these additional couplings has been found to have significant effect on the fusion excitation function of neutron-rich 11Be on 208Pb whereas the effect has been observed to be nominal for the case of proton-rich 17F on the same target. The pronounced effect of the channel coupling on the fusion process in the case of 11Be is attributed to its well-developed halo structure.

  12. Studies on the robustness of shock-ignited laser fusion targets

    Science.gov (United States)

    Atzeni, S.; Schiavi, A.; Marocchino, A.

    2011-03-01

    Several aspects of the sensitivity of a shock-ignited inertial fusion target to variation of parameters and errors or imperfections are studied by means of one-dimensional and two-dimensional numerical simulations. The study refers to a simple all-DT target, initially proposed for fast ignition (Atzeni et al 2007 Phys. Plasmas 7 052702) and subsequently shown to be also suitable for shock ignition (Ribeyre et al 2009 Plasma Phys. Control. Fusion 51 015013). It is shown that the growth of both Richtmyer-Meshkov and Rayleigh-Taylor instability (RTI) at the ablation front is reduced by laser pulses with an adiabat-shaping picket. An operating window for the parameters of the ignition laser spike is described; the threshold power depends on beam focusing and synchronization with the compression pulse. The time window for spike launch widens with beam power, while the minimum spike energy is independent of spike power. A large parametric scan indicates good tolerance (at the level of a few percent) to target mass and laser power errors. 2D simulations indicate that the strong igniting shock wave plays an important role in reducing deceleration-phase RTI growth. Instead, the high hot-spot convergence ratio (ratio of initial target radius to hot-spot radius at ignition) makes ignition highly sensitive to target mispositioning.

  13. Calculating fusion neutron energy spectra from arbitrary reactant distributions

    Science.gov (United States)

    Eriksson, J.; Conroy, S.; Andersson Sundén, E.; Hellesen, C.

    2016-02-01

    The Directional Relativistic Spectrum Simulator (DRESS) code can perform Monte-Carlo calculations of reaction product spectra from arbitrary reactant distributions, using fully relativistic kinematics. The code is set up to calculate energy spectra from neutrons and alpha particles produced in the D(d, n)3He and T(d, n)4He fusion reactions, but any two-body reaction can be simulated by including the corresponding cross section. The code has been thoroughly tested. The kinematics calculations have been benchmarked against the kinematics module of the ROOT Data Analysis Framework. Calculated neutron energy spectra have been validated against tabulated fusion reactivities and against an exact analytical expression for the thermonuclear fusion neutron spectrum, with good agreement. The DRESS code will be used as the core of a detailed synthetic diagnostic framework for neutron measurements at the JET and MAST tokamaks.

  14. Fusion excitation function measurement for 6Li+64Ni at near-barrier energies

    Directory of Open Access Journals (Sweden)

    Shaikh Md. Moin

    2015-01-01

    Full Text Available Total fusion excitation function has been measured for the reaction of weakly bound 6Li projectile on medium mass 64Ni target at energies near the Coulomb barrier of the system. Online characteristic γ-ray detection method has been used to identify and determine the cross sections of the residues. No suppression of total fusion cross section (σTF is observed at above barrier energies. But enhancement of measured cross section with respect to the one-dimensional barrier penetration model (1-DBPM calculation is observed at below barrier energies. The enhancement can not be explained by coupled channels calculation with dominant projectile and target excitations as well as one-neutron stripping reaction.

  15. Determination of Atomic Data Pertinent to the Fusion Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    Reader, J.

    2013-06-11

    We summarize progress that has been made on the determination of atomic data pertinent to the fusion energy program. Work is reported on the identification of spectral lines of impurity ions, spectroscopic data assessment and compilations, expansion and upgrade of the NIST atomic databases, collision and spectroscopy experiments with highly charged ions on EBIT, and atomic structure calculations and modeling of plasma spectra.

  16. Generation and compression of a target plasma for magnetized target fusion

    Energy Technology Data Exchange (ETDEWEB)

    Kirkpatrick, R.C.; Lindemuth, I.R.; Sheehey, P.T. [and others

    1998-11-01

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Magnetized target fusion (MTF) is intermediate between the two very different approaches to fusion: inertial and magnetic confinement fusion (ICF and MCF). Results from collaboration with a Russian MTF team on their MAGO experiments suggest they have a target plasma suitable for compression to provide an MTF proof of principle. This LDRD project had tow main objectives: first, to provide a computational basis for experimental investigation of an alternative MTF plasma, and second to explore the physics and computational needs for a continuing program. Secondary objectives included analytic and computational support for MTF experiments. The first objective was fulfilled. The second main objective has several facets to be described in the body of this report. Finally, the authors have developed tools for analyzing data collected on the MAGO a nd LDRD experiments, and have tested them on limited MAGO data.

  17. 76 FR 4645 - Fusion Energy Sciences Advisory Committee; Notice of Open Meeting

    Science.gov (United States)

    2011-01-26

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Fusion... Science. SUMMARY: This notice announces a meeting of the Fusion Energy Sciences Advisory Committee. The..., Office of Fusion Energy Sciences; U.S. Department of Energy; 1000 Independence Avenue, SW.;...

  18. The cytoplasmic domain of the gamete membrane fusion protein HAP2 targets the protein to the fusion site in Chlamydomonas and regulates the fusion reaction

    Science.gov (United States)

    Liu, Yanjie; Pei, Jimin; Grishin, Nick; Snell, William J.

    2015-01-01

    Cell-cell fusion between gametes is a defining step during development of eukaryotes, yet we know little about the cellular and molecular mechanisms of the gamete membrane fusion reaction. HAP2 is the sole gamete-specific protein in any system that is broadly conserved and shown by gene disruption to be essential for gamete fusion. The wide evolutionary distribution of HAP2 (also known as GCS1) indicates it was present in the last eukaryotic common ancestor and, therefore, dissecting its molecular properties should provide new insights into fundamental features of fertilization. HAP2 acts at a step after membrane adhesion, presumably directly in the merger of the lipid bilayers. Here, we use the unicellular alga Chlamydomonas to characterize contributions of key regions of HAP2 to protein location and function. We report that mutation of three strongly conserved residues in the ectodomain has no effect on targeting or fusion, although short deletions that include those residues block surface expression and fusion. Furthermore, HAP2 lacking a 237-residue segment of the cytoplasmic region is expressed at the cell surface, but fails to localize at the apical membrane patch specialized for fusion and fails to rescue fusion. Finally, we provide evidence that the ancient HAP2 contained a juxta-membrane, multi-cysteine motif in its cytoplasmic region, and that mutation of a cysteine dyad in this motif preserves protein localization, but substantially impairs HAP2 fusion activity. Thus, the ectodomain of HAP2 is essential for its surface expression, and the cytoplasmic region targets HAP2 to the site of fusion and regulates the fusion reaction. PMID:25655701

  19. High power microwave diagnostic for the fusion energy experiment ITER

    DEFF Research Database (Denmark)

    Korsholm, Søren Bang; Leipold, Frank; Goncalves, B.

    2016-01-01

    Microwave diagnostics will play an increasingly important role in burning plasma fusion energy experiments like ITER and beyond. The Collective Thomson Scattering (CTS) diagnostic to be installed at ITER is an example of such a diagnostic with great potential in present and future experiments....... The ITER CTS diagnostic will inject a 1 MW 60 GHz gyrotron beam into the ITER plasma and observe the scattering off fluctuations in the plasma — to monitor the dynamics of the fast ions generated in the fusion reactions....

  20. The role of the NIF in the development of inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Logan, B.G.

    1995-03-16

    Recent decisions by DOE to proceed with the National Ignition Facility (NIF) and the first half of the Induction Systems Linac Experiments (ILSE) can provide the scientific basis for inertial fusion ignition and high-repetition heavy-ion driver physics, respectively. Both are critical to Inertial Fusion Energy (IFE). A conceptual design has been completed for a 1.8-MJ, 500-TW, 0.35-{micro}m-solid-state laser system, the NIF. The NIF will demonstrate inertial fusion ignition and gain for national security applications, and for IFE development. It will support science applications using high-power lasers. The demonstration of inertial fusion ignition and gain, along with the parallel demonstration of the feasibility of an efficient, high-repetition-rate driver, would provide the basis for a follow-on Engineering Test Facility (ETF) identified in the National Energy Policy Act of 1992. The ETF would provide an integrated testbed for the development and demonstration of the technologies needed for IFE power plants. In addition to target physics of ignition, the NIF will contribute important data on IFE target chamber issues, including neutron damage, activation, target debris clearing, operational experience in many areas prototypical to future IFE power plants, and an opportunity to provide tests of candidate low-cost IFE targets and injection systems. An overview of the NIF design and the target area environments relevant to conducting IFE experiments are described in Section 2. In providing this basic data for IFE, the NIF will provide confidence that an ETF can be successful in the integration of drivers, target chambers, and targets for IFE.

  1. The National Ignition Facility: The Path to Ignition, High Energy Density Science and Inertial Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Moses, E

    2011-03-25

    The National Ignition Facility (NIF) at the Lawrence Livermore National Laboratory (LLNL) in Livermore, CA, is a Nd:Glass laser facility capable of producing 1.8 MJ and 500 TW of ultraviolet light. This world's most energetic laser system is now operational with the goals of achieving thermonuclear burn in the laboratory and exploring the behavior of matter at extreme temperatures and energy densities. By concentrating the energy from its 192 extremely energetic laser beams into a mm{sup 3}-sized target, NIF can produce temperatures above 100 million K, densities of 1,000 g/cm{sup 3}, and pressures 100 billion times atmospheric pressure - conditions that have never been created in a laboratory and emulate those in the interiors of planetary and stellar environments. On September 29, 2010, NIF performed the first integrated ignition experiment which demonstrated the successful coordination of the laser, the cryogenic target system, the array of diagnostics and the infrastructure required for ignition. Many more experiments have been completed since. In light of this strong progress, the U.S. and the international communities are examining the implication of achieving ignition on NIF for inertial fusion energy (IFE). A laser-based IFE power plant will require a repetition rate of 10-20 Hz and a 10% electrical-optical efficiency laser, as well as further advances in large-scale target fabrication, target injection and tracking, and other supporting technologies. These capabilities could lead to a prototype IFE demonstration plant in 10- to 15-years. LLNL, in partnership with other institutions, is developing a Laser Inertial Fusion Energy (LIFE) baseline design and examining various technology choices for LIFE power plant This paper will describe the unprecedented experimental capabilities of the NIF, the results achieved so far on the path toward ignition, the start of fundamental science experiments and plans to transition NIF to an international user facility

  2. Numerical studies of liners for magnetized target fusion (MTF)

    CERN Document Server

    Faehl, R J; Sheehey, P T; Lindemuth, I R

    1999-01-01

    Summary form only given. Magnetized target fusion (MTF) requires the fast compression of hot, dense plasmas by a conducting liner. We have used two-dimensional MHD calculations to study the electromagnetic implosion of metallic liners driven by realistic current waveforms. Parametric studies have indicated that the liner should reach velocities of 3-20 km/s, depending on the magnetic field configuration, and reach convergence ratios (initial radius divided by final radius) of at least 10. These parameters are accessible with large capacitor bank power supplies such as SHIVA or ATLAS, or with magnetic flux compression generators. One issue with the high currents that are required to implode the liner is that Ohmic heating will melt or vaporize the outer part of the liner. Calculations have shown that this is a realistic concern. We are currently addressing questions of liner instability and flux diffusion under MTF conditions. Another issue is that the magnetic fields needed to inhibit thermal losses to the wa...

  3. Emergence of FGFR family gene fusions as therapeutic targets in a wide spectrum of solid tumours.

    Science.gov (United States)

    Parker, Brittany C; Engels, Manon; Annala, Matti; Zhang, Wei

    2014-01-01

    The emergence of fibroblast growth factor receptor (FGFR) family fusions across diverse cancers has brought attention to FGFR-derived cancer therapies. The discovery of the first recurrent FGFR fusion in glioblastoma was followed by discoveries of FGFR fusions in bladder, lung, breast, thyroid, oral, and prostate cancers. Drug targeting of FGFR fusions has shown promising results and should soon be translating into clinical trials. FGFR fusions form as a result of various mechanisms – predominantly deletion for FGFR1, translocation for FGFR2, and tandem duplication for FGFR3. The ability to exploit the unique targetability of FGFR fusions proves that FGFR-derived therapies could have a promising future in cancer therapeutics. Drug targeting of fusion genes has proven to be an extremely effective therapeutic approach for cancers such as the recurrent BCR–ABL1 fusion in chronic myeloid leukaemia. The recent discovery of recurrent FGFR family fusions in several cancer types has brought to attention the unique therapeutic potential for FGFR-positive patients. Understanding the diverse mechanisms of FGFR fusion formation and their oncogenic potential will shed light on the impact of FGFR-derived therapy in the future.

  4. Complexity versus availability for fusion: The potential advantages of inertial fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Perkins, L.J.,

    1996-09-05

    Probably the single largest advantage of the inertial route to fusion energy (IFE) is the perception that its power plant embodiments could achieve acceptable capacity factors. This is a result of its relative simplicity, the decoupling of the driver and reactor chamber, and the potential to employ thick liquid walls. We examine these issues in terms of the complexity, reliability, maintainability and, therefore, availability of both magnetic and inertial fusion power plants and compare these factors with corresponding scheduled and unscheduled outage data from present day fission experience. We stress that, given the simple nature of a fission core, the vast majority of unplanned outages in fission plants are due to failures outside the reactor vessel itself Given we must be prepared for similar outages in the analogous plant external to a fusion power core, this puts severe demands on the reliability required of the fusion core itself. We indicate that such requirements can probably be met for IFE plants. We recommend that this advantage be promoted by performing a quantitative reliability and availability study for a representative IFE power plant and suggest that databases are probably adequate for this task.

  5. A study on target recognition fusion algorithm based on fuzzy theory

    Science.gov (United States)

    Han, Feng; Yang, WanHai

    2008-03-01

    In the process of the multi-sensors target recognition fusion, focused on the problem that it is difficult to determine the reliability of each sensor and how the data measured by different sensors are fused, a multi-sensor target recognition fusion method based on fuzzy theory is proposed. The mutual supportability of multiple sensors is obtained from the correlation function. Then by the membership function, the reliability of information provide by each sensor is gained. Finally, the supposed fusion result of multi-sensors target recognition can be produced on the basis of fuzzy integration function. The method is simple computationally and can objectively reflect the reliability of each sensor and interrelationship between these sensors. By applying the method to the target recognition, the simulation experiment shows that it can identify the target accurately and is an effective and feasible multi-sensors target recognition fusion method.

  6. HIV-1 gp41 Fusion Intermediate: A Target for HIV Therapeutics

    Directory of Open Access Journals (Sweden)

    Chungen Pan

    2010-02-01

    Full Text Available Human immunodeficiency virus (HIV-1 infection is initiated by the binding of gp120 envelope glyco-protein to its cell receptor (CD4 and a coreceptor (CXCR4 or CCR5, followed by a series of conformational changes in the gp41 transmembrane subunit. These changes include insertion of fusion peptide into the target cell membrane and association of C-heptad repeat (CHR peptide with the N-heptad repeat (NHR trimer, a pre-hairpin fusion intermediate. A stable six-helix bundle core is then formed, bringing the viral envelope and target cell membrane into close proximity for fusion. Peptides derived from the CHR region, such as T20 and C34, inhibit HIV-1 fusion by interacting with the gp41 fusion intermediate. A number of anti-HIV-1 peptides and small molecule compounds targeting the gp41 NHR-trimer have been identified. By combining HIV fusion/entry inhibitors targeting different sites in the gp41 fusion intermediate, a potent synergistic effect takes place, resulting in a potential new therapeutic strategy for the HIV infection/AIDS. Here, we present an overview of the current development of anti-HIV drugs, particularly those targeting the gp41 fusion intermediate.

  7. On the role of deformed Coulomb potential in fusion using energy density formalism

    Indian Academy of Sciences (India)

    Lavneet Kaur; Raj Kumari

    2015-10-01

    Using the Skyrme energy density formalism, the effect of deformed Coulomb potential on fusion barriers and fusion cross-sections is studied. Our detailed study reveals that the fusion barriers as well as fusion probabilities depend on the shape deformation (due to deformed Coulomb potential) of the colliding nuclei. However, this dependence due to deformed Coulomb potential is found to be very weak.

  8. Derivation of Energy Generated by Nuclear Fission-Fusion Reaction

    OpenAIRE

    Kayano, Hideo; Teshigawara, Makoto; Konashi, Kenji; Yamamoto, Takuya

    1994-01-01

    In the solids which contain fissionable elements and deuterium, it is expected that the energy generated by nuclear fission contributes to the promotion of the D-D nuclear fusion in the solids. When nuclear fission occurs by neutrons in the solid, the fissionable elements divide into two fission product nuclei having the energy of 100MeV, respectively. It is expected that the hige energy fission products promote rapidly nuclear fision reaction by knocking out the D atoms in the solids and by ...

  9. Results from systematic modeling of neutron damage in inertial fusion energy reactors

    Energy Technology Data Exchange (ETDEWEB)

    Perlado, J.M. E-mail: mperlado@denim.upm.es; Dominguez, E.; Malerba, L.; Marian, J.; Lodi, D.; Salvador, M.; Alonso, E.; Caturla, Ma.J.; Diaz de la Rubia, T

    2002-01-01

    Radiation damage is an important issue in the lifetime of the structural materials in an Inertial Fusion Energy (IFE) Reactor. The effect will strongly depend on the class of chamber protection at the IFE Reactor design. This paper gives results from DENIM, and collaboration with LLNL, on the necessary magnitudes for the final evaluation of neutron damage. The determination of the neutron intensities and energy spectra emerging from the target, the energy spectra of the Primary Knock-on Atoms (PKA) resulting from the neutron interactions, the modeling at microscopic scale of the pulsed irradiation in metals are reported, in addition to reference to the work on the time dependence of neutron flux in IFE protected chamber. Results are also presented on the damage accumulation in SiC, relevant both for magnetic (MFE) and inertial fusion.

  10. Semiconductor Laser Diode Pumps for Inertial Fusion Energy Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Deri, R J

    2011-01-03

    Solid-state lasers have been demonstrated as attractive drivers for inertial confinement fusion on the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) and at the Omega Facility at the Laboratory for Laser Energetics (LLE) in Rochester, NY. For power plant applications, these lasers must be pumped by semiconductor diode lasers to achieve the required laser system efficiency, repetition rate, and lifetime. Inertial fusion energy (IFE) power plants will require approximately 40-to-80 GW of peak pump power, and must operate efficiently and with high system availability for decades. These considerations lead to requirements on the efficiency, price, and production capacity of the semiconductor pump sources. This document provides a brief summary of these requirements, and how they can be met by a natural evolution of the current semiconductor laser industry. The detailed technical requirements described in this document flow down from a laser ampl9ifier design described elsewhere. In brief, laser amplifiers comprising multiple Nd:glass gain slabs are face-pumped by two planar diode arrays, each delivering 30 to 40 MW of peak power at 872 nm during a {approx} 200 {micro}s quasi-CW (QCW) pulse with a repetition rate in the range of 10 to 20 Hz. The baseline design of the diode array employs a 2D mosaic of submodules to facilitate manufacturing. As a baseline, they envision that each submodule is an array of vertically stacked, 1 cm wide, edge-emitting diode bars, an industry standard form factor. These stacks are mounted on a common backplane providing cooling and current drive. Stacks are conductively cooled to the backplane, to minimize both diode package cost and the number of fluid interconnects for improved reliability. While the baseline assessment in this document is based on edge-emitting devices, the amplifier design does not preclude future use of surface emitting diodes, which may offer appreciable future cost reductions and

  11. Feature-based fusion of infrared and visible dynamic images using target detection

    Institute of Scientific and Technical Information of China (English)

    Congyi Liu; Zhongliang Jing; Gang Xiao; Bo Yang

    2007-01-01

    We employ the target detection to improve the performance of the feature-based fusion of infrared and visible dynamic images, which forms a novel fusion scheme. First, the target detection is used to segment the source image sequences into target and background regions. Then, the dual-tree complex wavelet transform (DT-CWT) is proposed to decompose all the source image sequences. Different fusion rules are applied respectively in target and background regions to preserve the target information as much as possible. Real world infrared and visible image sequences are used to validate the performance of the proposed novel scheme. Compared with the previous fusion approaches of image sequences, the improvements of shift invariance, temporal stability and consistency, and computation cost are all ensured.

  12. Additive effects on the energy barrier for synaptic vesicle fusion cause supralinear effects on the vesicle fusion rate

    DEFF Research Database (Denmark)

    Schotten, Sebastiaan; Meijer, Marieke; Walter, Alexander Matthias

    2015-01-01

    supralinear effects on the fusion rate. To test this prediction experimentally, we developed a method to assess the number of releasable vesicles, rate constants for vesicle priming, unpriming, and fusion, and the activation energy for fusion by fitting a vesicle state model to synaptic responses induced......-linear effects of genetic/pharmacological perturbations on synaptic transmission and a novel interpretation of the cooperative nature of Ca2+-dependent release....

  13. The Spheromak path to fusion energy

    Energy Technology Data Exchange (ETDEWEB)

    Hooper, E.B., Barnes, C.W., Bellan, P.M., [and others

    1998-04-01

    The spheromak is a simple and robust magnetofluid configuration with several attractive reactor attributes including compact geometry, no material center post, high engineering {beta}, and sustained steady state operation through helicity injection. Spheromak physics was extensively studied in the US program and abroad (especially Japan) in the 1980` s with work continuing into the 1990s in Japan and the UK. Scientific results included demonstration of self-organization at constant helicity, control of the tilt and shift modes by shaped flux conservers, elucidation of the role of magnetic reconnection in the magnetic dynamo, and sustainment of a spheromak by helicity injection. Several groups attained electron temperatures above 100 eV in decaying plasmas, with CTX reaching 400 eV. This experiment had high magnetic field (>l T on the edge and {approximately} 3 T near the symmetry axis) and good confinement. More recently, analysis of CTX found the energy confinement in the plasma core to be consistent with Rechester-Rosenbluth transport in a fluctuating magnetic field, potentially scaling to good confinement at higher electron temperatures. The SPHEX group developed an understanding of the dynamo in sustained spheromaks but in a relatively cold device. These and other physics results provide a foundation for a new ``concept exploration`` experiment to study the physics of a hot, sustained spheromak. If successful, this work leads to a next generation, proof-of-principle program. The new SSPX experiment will address the physics of a large-scale sustained spheromak in a national laboratory (LLNL) setting. The key issue in near term spheromak research will be to explore the possibly deleterious effects of sustainment on confinement. Other important issues include exploring the {beta} scaling of confinement, scaling with Lundquist number S, and determining the need for active current-profile control. Collaborators from universities and other national laboratories are

  14. The National Ignition Facility and the Promise of Inertial Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Moses, E I

    2010-12-13

    The National Ignition Facility (NIF) at the Lawrence Livermore National Laboratory (LLNL) in Livermore, CA, is now operational. The NIF is the world's most energetic laser system capable of producing 1.8 MJ and 500 TW of ultraviolet light. By concentrating the energy from its 192 extremely energetic laser beams into a mm{sup 3}-sized target, NIF can produce temperatures above 100 million K, densities of 1,000 g/cm{sup 3}, and pressures 100 billion times atmospheric pressure - conditions that have never been created in a laboratory and emulate those in planetary interiors and stellar environments. On September 29, 2010, the first integrated ignition experiment was conducted, demonstrating the successful coordination of the laser, cryogenic target system, array of diagnostics and infrastructure required for ignition demonstration. In light of this strong progress, the U.S. and international communities are examining the implication of NIF ignition for inertial fusion energy (IFE). A laser-based IFE power plant will require a repetition rate of 10-20 Hz and a laser with 10% electrical-optical efficiency, as well as further development and advances in large-scale target fabrication, target injection, and other supporting technologies. These capabilities could lead to a prototype IFE demonstration plant in the 10- to 15-year time frame. LLNL, in partnership with other institutions, is developing a Laser Inertial Fusion Engine (LIFE) concept and examining in detail various technology choices, as well as the advantages of both pure fusion and fusion-fission schemes. This paper will describe the unprecedented experimental capabilities of the NIF and the results achieved so far on the path toward ignition. The paper will conclude with a discussion about the need to build on the progress on NIF to develop an implementable and effective plan to achieve the promise of LIFE as a source of carbon-free energy.

  15. Fusion genes in solid tumors:an emerging target for cancer diagnosis and treatment

    Institute of Scientific and Technical Information of China (English)

    Brittany C. Parker; Wei Zhang

    2013-01-01

    Studies over the past decades have uncovered fusion genes, a class of oncogenes that provide immense diagnostic and therapeutic advantages because of their tumor-specific expression. Originally associated with hemotologic cancers, fusion genes have recently been discovered in a wide array of solid tumors, including sarcomas, carcinomas, and tumors of the central nervous system. Fusion genes are attractive as both therapeutic targets and diagnostic tools due to their inherent expression in tumor tissue alone. Therefore, the discovery and elucidation of fusion genes in various cancer types may provide more effective therapies in the future for cancer patients.

  16. Near- and sub-barrier fusion of 20O incident ions with 12C target nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Rudolph, M. J. [Indiana University; Gosser, Z. Q. [Indiana University; Brown, K [Indiana University; De Souza, R. T. [Indiana University; Chbihi, A. [GANIL, CEA, Caen, France & CNRS, IN2P3, Caen, France; Jacquot, B. [GANIL, CEA, Caen, France & CNRS, IN2P3, Caen, France; Famiano, M. [Western Michigan University; Liang, J Felix [ORNL; Shapira, Dan [ORNL; Mercier, D. [Centre de Calcul du CNRS, France

    2012-01-01

    Evaporation residues resulting from fusion of {sup 20}O incident ions with {sup 12}C target nuclei have been measured for the first time. The cross-section associated with compound nuclei that de-excite via emission of charged particles is extracted. The resulting excitation function is compared with the predictions of a standard fusion model followed by statistical decay code. A significant underprediction of the measured cross-section by the fusion-evaporation model raises the question of whether the fusion cross-section is larger for the neutron-rich projectile or the statistical de-excitation is incorrectly predicted.

  17. Potential need for fusion in the U. S. energy system

    Energy Technology Data Exchange (ETDEWEB)

    Beardsworth, E; Powell, J

    1977-09-01

    For fusion to become available for commercial use in the 21st century, R and D must be undertaken now. But it is hard to justify these expenditures with a ''cost/benefit'' oriented assessment methodology, because of both the time frame and the uncertainty of the future benefits. Focusing on the factors most relevant for current consideration of fusion's commercial prospects, i.e., consumption levels and the outcomes for fission, solar, and coal, many possible futures of the U.S. energy system are posited and analyzed under various assumptions about costs. The ''Reference Energy System'' approach was modified to establish both an appropriate degree of detail and explicit time dependence, and a computer code used to organize the relevant data and to perform calculations of system cost (annual and discounted present value), resource use, and residuals that are implied by the consumption levels and technology mix in each scenario. Not-unreasonable scenarios indicate benefits in the form of direct cost savings, which may well exceed R and D costs, which could be attributed to the implementation of fusion.

  18. Airborne Infrared and Visible Image Fusion for Target Perception Based on Target Region Segmentation and Discrete Wavelet Transform

    Directory of Open Access Journals (Sweden)

    Yifeng Niu

    2012-01-01

    Full Text Available Infrared and visible image fusion is an important precondition of realizing target perception for unmanned aerial vehicles (UAVs, then UAV can perform various given missions. Information of texture and color in visible images are abundant, while target information in infrared images is more outstanding. The conventional fusion methods are mostly based on region segmentation; as a result, the fused image for target recognition could not be actually acquired. In this paper, a novel fusion method of airborne infrared and visible image based on target region segmentation and discrete wavelet transform (DWT is proposed, which can gain more target information and preserve more background information. The fusion experiments are done on condition that the target is unmoving and observable both in visible and infrared images, targets are moving and observable both in visible and infrared images, and the target is observable only in an infrared image. Experimental results show that the proposed method can generate better fused image for airborne target perception.

  19. Rugged Packaging for Damage Resistant Inertial Fusion Energy Optics

    Energy Technology Data Exchange (ETDEWEB)

    Stelmack, Larry

    2003-11-17

    The development of practical fusion energy plants based on inertial confinement with ultraviolet laser beams requires durable, stable final optics that will withstand the harsh fusion environment. Aluminum-coated reflective surfaces are fragile, and require hard overcoatings resistant to contamination, with low optical losses at 248.4 nanometers for use with high-power KrF excimer lasers. This program addresses the definition of requirements for IFE optics protective coatings, the conceptual design of the required deposition equipment according to accepted contamination control principles, and the deposition and evaluation of diamondlike carbon (DLC) test coatings. DLC coatings deposited by Plasma Immersion Ion Processing were adherent and abrasion-resistant, but their UV optical losses must be further reduced to allow their use as protective coatings for IFE final optics. Deposition equipment for coating high-performance IFE final optics must be designed, constructed, and operated with contamination control as a high priority.

  20. Designing Radiation Resistance in Materials for Fusion Energy

    Science.gov (United States)

    Zinkle, S. J.; Snead, L. L.

    2014-07-01

    Proposed fusion and advanced (Generation IV) fission energy systems require high-performance materials capable of satisfactory operation up to neutron damage levels approaching 200 atomic displacements per atom with large amounts of transmutant hydrogen and helium isotopes. After a brief overview of fusion reactor concepts and radiation effects phenomena in structural and functional (nonstructural) materials, three fundamental options for designing radiation resistance are outlined: Utilize matrix phases with inherent radiation tolerance, select materials in which vacancies are immobile at the design operating temperatures, or engineer materials with high sink densities for point defect recombination. Environmental and safety considerations impose several additional restrictions on potential materials systems, but reduced-activation ferritic/martensitic steels (including thermomechanically treated and oxide dispersion-strengthened options) and silicon carbide ceramic composites emerge as robust structural materials options. Materials modeling (including computational thermodynamics) and advanced manufacturing methods are poised to exert a major impact in the next ten years.

  1. Systems Modeling For The Laser Fusion-Fission Energy (LIFE) Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Meier, W R; Abbott, R; Beach, R; Blink, J; Caird, J; Erlandson, A; Farmer, J; Halsey, W; Ladran, T; Latkowski, J; MacIntyre, A; Miles, R; Storm, E

    2008-10-02

    A systems model has been developed for the Laser Inertial Fusion-Fission Energy (LIFE) power plant. It combines cost-performance scaling models for the major subsystems of the plant including the laser, inertial fusion target factory, engine (i.e., the chamber including the fission and tritium breeding blankets), energy conversion systems and balance of plant. The LIFE plant model is being used to evaluate design trade-offs and to identify high-leverage R&D. At this point, we are focused more on doing self consistent design trades and optimization as opposed to trying to predict a cost of electricity with a high degree of certainty. Key results show the advantage of large scale (>1000 MWe) plants and the importance of minimizing the cost of diodes and balance of plant cost.

  2. New results in low-energy fusion of 40Ca+Zr,9290

    Science.gov (United States)

    Stefanini, A. M.; Montagnoli, G.; Esbensen, H.; Čolović, P.; Corradi, L.; Fioretto, E.; Galtarossa, F.; Goasduff, A.; Grebosz, J.; Haas, F.; Mazzocco, M.; Soić, N.; Strano, E.; Szilner, S.

    2017-07-01

    Background: Near- and sub-barrier fusion of various Ca + Zr isotopic combinations have been widely investigated. A recent analysis of 40Ca+96Zr data has highlighted the importance of couplings to multiphonon excitations and to both neutron and proton transfer channels. Analogous studies of 40Ca+90Zr tend to exclude any role of transfer couplings. However, the lowest measured cross section for this system is rather high (840 μ b ). A rather complete data set is available for 40Ca+94Zr , while no measurement of 40Ca+92Zr fusion has been performed in the past. Purpose: Our aim is to measure the full excitation function of 40Ca+92Zr near the barrier and to extend downward the existing data on 40Ca+90Zr , in order to estimate the transfer couplings that should be used in coupled-channels calculations of the fusion of these two systems and of 40Ca+94Zr . Methods: 40Ca beams from the XTU Tandem accelerator of INFN-Laboratori Nazionali di Legnaro were used, bombarding thin metallic 90Zr (50 μ g /cm2 ) and 92ZrO2 targets (same thickness) enriched to 99.36 % and 98.06 % in masses 90 and 92, respectively. An electrostatic beam deflector allowed the detection of fusion evaporation residues (ER) at very forward angles, and angular distributions of ER were measured. Results: The excitation function of 40Ca+92Zr has been measured down to the level of ≃60 μ b . Coupled-channels (CC) calculations using a standard Woods-Saxon (WS) potential and following the line of a previous analysis of 40Ca+96Zr fusion data give a good account of the new data, as well as of the existing data for 40Ca+94Zr . The previous excitation function of 40Ca+90Zr has been extended down to 40 μ b . Conclusions: Transfer couplings play an important role in explaining the fusion data for 40Ca+92Zr and 40Ca+94Zr . The strength of the pair-transfer coupling is deduced by applying a simple recipe based on the value obtained for 40Ca+96Zr . The logarithmic slopes and the S factors for fusion are reproduced

  3. Investigation of incomplete fusion dynamics at energy 4-8 MeV/nucleon

    Science.gov (United States)

    Kumar, Harish; Tali, Suhail A.; Ansari, M. Afzal; Singh, D.; Ali, Rahbar; Kumar, Kamal; Sathik, N. P. M.; Parashari, Siddharth; Ali, Asif; Dubey, R.; Bala, Indu; Kumar, Rakesh; Singh, R. P.; Muralithar, S.

    2017-04-01

    The recoil-catcher activation technique followed by the offline γ-ray spectroscopy has been adopted for the excitation function measurement of residues populated in 12,13C induced reactions with 175Lu target at lower projectile energies ≈ 4- 8 MeV /nucleon. The independent cross-sections for some of the populated residues have been estimated by subtracting the contributions of higher charge precursor isobars from the measured cumulative cross-sections. The measured excitation functions are compared with theoretical predictions based on statistical model code PACE-4. This comparison reveals that complete fusion process solely contributes in the formation of xn-pxn channels and an enhancement in the measured cross-sections of α-emitting channels from the theoretical predictions may be attributed to the incomplete fusion process. The incomplete fusion probability is found to be higher in case of 12C than for a one neutron rich projectile 13C throughout the incident energy region. Present findings obtained for 12,13C + 175Lu systems have been compared with informations extracted from previously studied systems and projectile structure is found to strongly affect the incomplete fusion dynamics in terms of projectile α-Q-value along with projectile-target mass-asymmetry. Moreover, it may be pointed out that Morgenstern's mass-asymmetry systematic is probably the projectile structure dependent systematic. A substantial contribution to incomplete fusion coming from collision trajectories with ℓ ≤ℓcrit is also observed, contrary to the SUMRULE model assumptions.

  4. Low-energy nuclear fusion data and their relation to magnetic and laser fusion

    Energy Technology Data Exchange (ETDEWEB)

    Jarmie, N.

    1980-04-01

    The accuracy of the basic fusion data for the T(d,n)/sup 4/He, /sup 3/He(d,p)/sup 4/He, T(t,2n)/sup 4/He, D(d,n)/sup 3/He, and D(d,p)T reactions was investigated in the 10- to 100-keV bombarding energy region, and the effects of inaccuracies on the design of fusion reactors were assessed. The data base for these reactions (particularly, the most critical T(d,n)/sup 4/He reaction) rests on 25-year-old experiments the accuracy (often assumed to be +- 5%) of which has rarely been questioned: yet, in all except the d + d reactions, there are significant differences among data sets. The errors in the basic data sets may be considerably larger than previously expected, and the effect on design calculations should be significant. Much of the trouble apparently lies in the accuracy of the energy measurements, which are difficult at low energies. Systematic errors of up to 50% are possible in the reactivity values of the present T(d,n)/sup 4/He data base. The errors in the reactivity will propagate proportionately into the errors in fusion probabilities in reactor calculations. /sup 3/He(d,p)/sup 4/He reaction cross sections could be in error by as much as 50% in the low-energy region. The D(d,n)/sup 3/He and D(d,p)T cross sections appear to be well known and consistent. The T(t,2n)/sup 4/He cross section is poorly known and may be subject to large systematic errors. Improved absolute measurements for all the reactions in the low bombarding energy region (10 to 100 keV) are needed, but until they are done, the data sets should be left as they are (except for T(t,2n)/sup 4/He data, which could be lowered by about 50%). The apparent uncertainties of these data sets should be kept in mind. 14 figures.

  5. A Fusion Neutron Source Driven Sub-Critical Nuclear Energy System: A Way for Early Application of Fusion Technology

    Institute of Scientific and Technical Information of China (English)

    吴宜灿

    2001-01-01

    This paper proposes a sub-critical nuclear energy system driven by fusion neutron source, FDS, which can be used to transmute long-lived radioactive wastes and to produce fissile nuclear fuel as a way for early application of fusion technology. The necessity and feasibility to develop that system in China are illustrated on the basis of prediction of the demand of energy source in the first half of the 21th century, the status of current fission energy supply and the progress in fusion technology in the vorld. The characteristics of fusion neutron driver and the potential for transmutation of long-lived nuclear wastes and breeding of fissile nuclear fuel in a blanket are analyzed. A scenario of development steps is proposed.``

  6. Robust Ground Target Detection by SAR and IR Sensor Fusion Using Adaboost-Based Feature Selection.

    Science.gov (United States)

    Kim, Sungho; Song, Woo-Jin; Kim, So-Hyun

    2016-07-19

    Long-range ground targets are difficult to detect in a noisy cluttered environment using either synthetic aperture radar (SAR) images or infrared (IR) images. SAR-based detectors can provide a high detection rate with a high false alarm rate to background scatter noise. IR-based approaches can detect hot targets but are affected strongly by the weather conditions. This paper proposes a novel target detection method by decision-level SAR and IR fusion using an Adaboost-based machine learning scheme to achieve a high detection rate and low false alarm rate. The proposed method consists of individual detection, registration, and fusion architecture. This paper presents a single framework of a SAR and IR target detection method using modified Boolean map visual theory (modBMVT) and feature-selection based fusion. Previous methods applied different algorithms to detect SAR and IR targets because of the different physical image characteristics. One method that is optimized for IR target detection produces unsuccessful results in SAR target detection. This study examined the image characteristics and proposed a unified SAR and IR target detection method by inserting a median local average filter (MLAF, pre-filter) and an asymmetric morphological closing filter (AMCF, post-filter) into the BMVT. The original BMVT was optimized to detect small infrared targets. The proposed modBMVT can remove the thermal and scatter noise by the MLAF and detect extended targets by attaching the AMCF after the BMVT. Heterogeneous SAR and IR images were registered automatically using the proposed RANdom SAmple Region Consensus (RANSARC)-based homography optimization after a brute-force correspondence search using the detected target centers and regions. The final targets were detected by feature-selection based sensor fusion using Adaboost. The proposed method showed good SAR and IR target detection performance through feature selection-based decision fusion on a synthetic database generated

  7. Robust Ground Target Detection by SAR and IR Sensor Fusion Using Adaboost-Based Feature Selection

    Directory of Open Access Journals (Sweden)

    Sungho Kim

    2016-07-01

    Full Text Available Long-range ground targets are difficult to detect in a noisy cluttered environment using either synthetic aperture radar (SAR images or infrared (IR images. SAR-based detectors can provide a high detection rate with a high false alarm rate to background scatter noise. IR-based approaches can detect hot targets but are affected strongly by the weather conditions. This paper proposes a novel target detection method by decision-level SAR and IR fusion using an Adaboost-based machine learning scheme to achieve a high detection rate and low false alarm rate. The proposed method consists of individual detection, registration, and fusion architecture. This paper presents a single framework of a SAR and IR target detection method using modified Boolean map visual theory (modBMVT and feature-selection based fusion. Previous methods applied different algorithms to detect SAR and IR targets because of the different physical image characteristics. One method that is optimized for IR target detection produces unsuccessful results in SAR target detection. This study examined the image characteristics and proposed a unified SAR and IR target detection method by inserting a median local average filter (MLAF, pre-filter and an asymmetric morphological closing filter (AMCF, post-filter into the BMVT. The original BMVT was optimized to detect small infrared targets. The proposed modBMVT can remove the thermal and scatter noise by the MLAF and detect extended targets by attaching the AMCF after the BMVT. Heterogeneous SAR and IR images were registered automatically using the proposed RANdom SAmple Region Consensus (RANSARC-based homography optimization after a brute-force correspondence search using the detected target centers and regions. The final targets were detected by feature-selection based sensor fusion using Adaboost. The proposed method showed good SAR and IR target detection performance through feature selection-based decision fusion on a synthetic

  8. Night vision image fusion for target detection with improved 2D maximum entropy segmentation

    Science.gov (United States)

    Bai, Lian-fa; Liu, Ying-bin; Yue, Jiang; Zhang, Yi

    2013-08-01

    Infrared and LLL image are used for night vision target detection. In allusion to the characteristics of night vision imaging and lack of traditional detection algorithm for segmentation and extraction of targets, we propose a method of infrared and LLL image fusion for target detection with improved 2D maximum entropy segmentation. Firstly, two-dimensional histogram was improved by gray level and maximum gray level in weighted area, weights were selected to calculate the maximum entropy for infrared and LLL image segmentation by using the histogram. Compared with the traditional maximum entropy segmentation, the algorithm had significant effect in target detection, and the functions of background suppression and target extraction. And then, the validity of multi-dimensional characteristics AND operation on the infrared and LLL image feature level fusion for target detection is verified. Experimental results show that detection algorithm has a relatively good effect and application in target detection and multiple targets detection in complex background.

  9. Elise: The next step in development of induction heavy ion drivers for inertial fusion energy

    Science.gov (United States)

    Lee, E.; Bangerter, R. O.; Celata, C.; Faltens, A.; Fessenden, T.; Peters, C.; Pickrell, J.; Reginato, L.; Seidl, P.; Yu, S.

    1994-11-01

    LBL, with the participation of LLNL and industry, proposes to build Elise, an electric-focused accelerator as the next logical step towards the eventual goal of a heavy-ion induction linac powerful enough to implode or 'drive' inertial-confinement fusion targets. Elise will be at full driver scale in several important parameters-most notably line charge density (a function of beam size), which was not explored in earlier experiments. Elise will be capable of accelerating and electrostatically focusing four parallel, full-scale ion beams and will be designed to be extendible, by successive future construction projects, to meet the goal of the USA DOE Inertial Fusion Energy program (IFE). This goal is to address all remaining issues in heavy-ion IFE except target physics, which is currently the responsibility of DOE Defense Programs, and the target chamber. Thus Elise is the first step of a program that will provide a solid foundation of data for further progress toward a driver, as called for in the National Energy Strategy and National Energy Policy Act.

  10. Belief Function Based Decision Fusion for Decentralized Target Classification in Wireless Sensor Networks.

    Science.gov (United States)

    Zhang, Wenyu; Zhang, Zhenjiang

    2015-08-19

    Decision fusion in sensor networks enables sensors to improve classification accuracy while reducing the energy consumption and bandwidth demand for data transmission. In this paper, we focus on the decentralized multi-class classification fusion problem in wireless sensor networks (WSNs) and a new simple but effective decision fusion rule based on belief function theory is proposed. Unlike existing belief function based decision fusion schemes, the proposed approach is compatible with any type of classifier because the basic belief assignments (BBAs) of each sensor are constructed on the basis of the classifier's training output confusion matrix and real-time observations. We also derive explicit global BBA in the fusion center under Dempster's combinational rule, making the decision making operation in the fusion center greatly simplified. Also, sending the whole BBA structure to the fusion center is avoided. Experimental results demonstrate that the proposed fusion rule has better performance in fusion accuracy compared with the naïve Bayes rule and weighted majority voting rule.

  11. Report of the Fusion Energy Sciences Advisory Committee. Panel on Integrated Simulation and Optimization of Magnetic Fusion Systems

    Energy Technology Data Exchange (ETDEWEB)

    Dahlburg, Jill [General Atomics, San Diego, CA (United States); Corones, James [Krell Inst., Ames, IA (United States); Batchelor, Donald [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bramley, Randall [Indiana Univ., Bloomington, IN (United States); Greenwald, Martin [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Jardin, Stephen [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Krasheninnikov, Sergei [Univ. of California, San Diego, CA (United States); Laub, Alan [Univ. of California, Davis, CA (United States); Leboeuf, Jean-Noel [Univ. of California, Los Angeles, CA (United States); Lindl, John [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lokke, William [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rosenbluth, Marshall [Univ. of California, San Diego, CA (United States); Ross, David [Univ. of Texas, Austin, TX (United States); Schnack, Dalton [Science Applications International Corporation, Oak Ridge, TN (United States)

    2002-11-01

    Fusion is potentially an inexhaustible energy source whose exploitation requires a basic understanding of high-temperature plasmas. The development of a science-based predictive capability for fusion-relevant plasmas is a challenge central to fusion energy science, in which numerical modeling has played a vital role for more than four decades. A combination of the very wide range in temporal and spatial scales, extreme anisotropy, the importance of geometric detail, and the requirement of causality which makes it impossible to parallelize over time, makes this problem one of the most challenging in computational physics. Sophisticated computational models are under development for many individual features of magnetically confined plasmas and increases in the scope and reliability of feasible simulations have been enabled by increased scientific understanding and improvements in computer technology. However, full predictive modeling of fusion plasmas will require qualitative improvements and innovations to enable cross coupling of a wider variety of physical processes and to allow solution over a larger range of space and time scales. The exponential growth of computer speed, coupled with the high cost of large-scale experimental facilities, makes an integrated fusion simulation initiative a timely and cost-effective opportunity. Worldwide progress in laboratory fusion experiments provides the basis for a recent FESAC recommendation to proceed with a burning plasma experiment (see FESAC Review of Burning Plasma Physics Report, September 2001). Such an experiment, at the frontier of the physics of complex systems, would be a huge step in establishing the potential of magnetic fusion energy to contribute to the world’s energy security. An integrated simulation capability would dramatically enhance the utilization of such a facility and lead to optimization of toroidal fusion plasmas in general. This science-based predictive capability, which was cited in the FESAC

  12. Muon-catalyzed fusion experiment target and detector system. Preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    Jones, S.E.; Watts, K.D.; Caffrey, A.J.; Walter, J.B.

    1982-03-01

    We present detailed plans for the target and particle detector systems for the muon-catalyzed fusion experiment. Requirements imposed on the target vessel by experimental conditions and safety considerations are delineated. Preliminary designs for the target vessel capsule and secondary containment vessel have been developed which meet these requirements. In addition, the particle detection system is outlined, including associated fast electronics and on-line data acquisition. Computer programs developed to study the target and detector system designs are described.

  13. A novel bispecific peptide HIV-1 fusion inhibitor targeting the N-terminal heptad repeat and fusion peptide domains in gp41.

    Science.gov (United States)

    Jiang, Xifeng; Jia, Qiyan; Lu, Lu; Yu, Fei; Zheng, Jishen; Shi, Weiguo; Cai, Lifeng; Jiang, Shibo; Liu, Keliang

    2016-12-01

    HIV-1 fusion with the target cell is initiated by the insertion of the gp41 fusion peptide (FP) into the target cell membrane and the interaction between the gp41 N- and C-terminal heptad repeats (NHR and CHR), followed by the formation of the six-helix bundle (6-HB) fusion core. Therefore, both FP and NHR are important targets for HIV-1 fusion inhibitors. Here, we designed and synthesized a dual-target peptidic HIV-1 fusion inhibitor, 4HR-LBD-VIRIP, in which 4HR-LBD is able to bind to the gp41 NHR domain, while VIRIP is able to interact with gp41 FP. We found that 4HR-LBD-VIRIP is about tenfold more potent than 4HR-LBD and VIRIP in inhibiting HIV-1IIIB infection and HIV-1 envelope glycoprotein (Env)-mediated cell-cell fusion, suggesting that this dual-target HIV-1 fusion inhibitor possesses a strong synergistic antiviral effect. A biophysical analysis indicates that 4HR-LBD-VIRIP can interact with N70 peptide that contains the gp41 NHR and FP domains and binds with lipid membrane. This study provides a new approach for designing novel viral fusion inhibitors against HIV and other enveloped viruses with class I membrane fusion proteins.

  14. Achieving the Renewable Energy Target for Jamaica

    Directory of Open Access Journals (Sweden)

    Abdullahi Olabode ABDULKADRI

    2014-05-01

    Full Text Available ieving the Renewable Energy Target for Jamaica Abstract: The high cost of energy in Jamaica, one of the highest in the Caribbean region, is usually cited as a hindrance to industrial development and efficiency, especially in the manufacturing sector. High energy cost is also considered to be a national energy security issue and the government is taking steps to ensure adequate supply of energy at affordable prices. In the current National Development Plan, the government has set a target for renewable energy sources to supply 20% of the country's energy need by the year 2030. Using a linear programing model of energy planning, we examine how realistically this target could be achieved. Our findings indicate that the 20% renewable energy target is technically achievable with the optimal plan showing a mixture of wind power, hydropower and bagasse power but no solar power. However, when the timeline for investment in new generating capacities that will ensure the attainment of the target is considered, it becomes highly improbable that the target will be met. This study fills the gap that exists in evidence-based analysis of energy policy in Jamaica.

  15. Analysis of heavy-ion fusion reactions at extreme sub-barrier energies using the proximity formalism

    Science.gov (United States)

    Ghodsi, O. N.; Gharaei, R.

    2013-11-01

    The recent measured values of the fusion excitation functions of the heavy-ion colliding systems 28Si+100Mo, 58Ni+54Fe, and 64Ni+64Ni are investigated using the original version of the proximity formalism. The fusion cross sections are calculated based on the coupled-channels approach, including couplings to the low-lying 2+ and 3- states in both target and projectile nuclei. The comparison between the calculated and the measured values of the fusion excitation functions indicates that the potential Prox.77 needs to be modified considerably at sub-barrier energies. In the present study, the role of the surface energy coefficient γ and also the temperature T of the compound nucleus in nuclear potential and fusion cross section has been explored for our colliding systems. Moreover, the mutual and the multiphonon excitations of the lowest 2+ and 3- states are considered in the coupled-channels calculations. It is demonstrated that the potential Prox.77 with these corrective effects can reproduce the experimental data of the fusion cross section, the S factor and the logarithmic derivative for fusion reactions 28Si+100Mo, 58Ni+54Fe, and 64Ni+64Ni with good accuracy especially at below-barrier energies.

  16. Magnetic compression/magnetized target fusion (MAGO/MTF), an update

    Energy Technology Data Exchange (ETDEWEB)

    Kirkpatrick, R.C.; Lindemuth, I.R.

    1998-03-01

    Magnetized Target Fusion (MTF) was reported in two papers at the First Symposium on Current Trends in International Fusion Research. MTF is intermediate between two very different mainline approaches to fusion: Inertial Confinement Fusion (ICF) and magnetic confinement fusion (MCF). The only US MTF experiments in which a target plasma was compressed were the Sandia National Laboratory ``Phi targets``. Despite the very interesting results from that series of experiments, the research was not pursued, and other embodiments of MTF concept such as the Fast Liner were unable to attract the financial support needed for a firm proof of principle. A mapping of the parameter space for MTF showed the significant features of this approach. The All-Russian Scientific Research Institute of Experimental Physics (VNIIEF) has an on-going interest in this approach to thermonuclear fusion, and Los Alamos National Laboratory (LANL) and VNIIEF have done joint target plasma generation experiments relevant to MTF referred to as MAGO (transliteration of the Russian acronym for magnetic compression). The MAGO II experiment appears to have achieved on the order of 200 eV and over 100 KG, so that adiabatic compression with a relatively small convergence could bring the plasma to fusion temperatures. In addition, there are other experiments being pursued for target plasma generation and proof of principle. This paper summarizes the previous reports on MTF and MAGO and presents the progress that has been made over the past three years in creating a target plasma that is suitable for compression to provide a scientific proof of principle experiment for MAGO/MTF.

  17. An Efficient Method for Identifying Gene Fusions by Targeted RNA Sequencing from Fresh Frozen and FFPE Samples.

    Directory of Open Access Journals (Sweden)

    Jonathan A Scolnick

    Full Text Available Fusion genes are known to be key drivers of tumor growth in several types of cancer. Traditionally, detecting fusion genes has been a difficult task based on fluorescent in situ hybridization to detect chromosomal abnormalities. More recently, RNA sequencing has enabled an increased pace of fusion gene identification. However, RNA-Seq is inefficient for the identification of fusion genes due to the high number of sequencing reads needed to detect the small number of fusion transcripts present in cells of interest. Here we describe a method, Single Primer Enrichment Technology (SPET, for targeted RNA sequencing that is customizable to any target genes, is simple to use, and efficiently detects gene fusions. Using SPET to target 5701 exons of 401 known cancer fusion genes for sequencing, we were able to identify known and previously unreported gene fusions from both fresh-frozen and formalin-fixed paraffin-embedded (FFPE tissue RNA in both normal tissue and cancer cells.

  18. An Efficient Method for Identifying Gene Fusions by Targeted RNA Sequencing from Fresh Frozen and FFPE Samples.

    Science.gov (United States)

    Scolnick, Jonathan A; Dimon, Michelle; Wang, I-Ching; Huelga, Stephanie C; Amorese, Douglas A

    2015-01-01

    Fusion genes are known to be key drivers of tumor growth in several types of cancer. Traditionally, detecting fusion genes has been a difficult task based on fluorescent in situ hybridization to detect chromosomal abnormalities. More recently, RNA sequencing has enabled an increased pace of fusion gene identification. However, RNA-Seq is inefficient for the identification of fusion genes due to the high number of sequencing reads needed to detect the small number of fusion transcripts present in cells of interest. Here we describe a method, Single Primer Enrichment Technology (SPET), for targeted RNA sequencing that is customizable to any target genes, is simple to use, and efficiently detects gene fusions. Using SPET to target 5701 exons of 401 known cancer fusion genes for sequencing, we were able to identify known and previously unreported gene fusions from both fresh-frozen and formalin-fixed paraffin-embedded (FFPE) tissue RNA in both normal tissue and cancer cells.

  19. Analysis of the low- and high-energy fusion cross sections: the case of 58Ni+54Fe

    Science.gov (United States)

    Gharaei, R.

    2017-04-01

    The importance of the saturation effect of cold nuclear matter (NM) on describing the fusion hindrance phenomenon at extremely low incident energies is investigated for the medium-heavy mass system of 58Ni+54Fe. From the theoretical viewpoint, for considering the mentioned property during the fusion process one can use the double-folding (DF) model which is modified through the repulsive core effects as a basic heavy ion–ion potential. The theoretical calculations of the fusion cross sections are performed using the coupled-channel technique, including couplings to the low-lying {2}+ and {3}- states in target and projectile. It is shown that the corrective effects of the cold NM provide an appropriate description for the energy-dependent behavior of the measured fusion cross sections at extremely low incident energies. Moreover, we find that the calculated results of the astrophysical S factor and the logarithmic derivative based on the modified form of the DF model are in good agreement with the corresponding experimental data at these energies. A discussion is also presented about the predictions of the present sudden approach for the behavior of the fusion cross sections at high incident energies. The obtained results reveal that this behavior depends on the nuclear structure of the reacting nuclei.

  20. Reduced cost design of liquid lithium target for international fusion material irradiation facility (IFMIF)

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Hiroo; Ida, Mizuho; Sugimoto, Masayoshi; Takeuchi, Hiroshi [Department of Fussion Engineering Research, Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Yutani, Toshiaki [Toshiba Corp., Tokyo (Japan)

    2001-01-01

    The International Fusion Materials Irradiation Facility (IFMIF) is being jointly planned to provide an accelerator-based D-Li neutron source to produce intense high energy neutrons (2 MW/m{sup 2}) up to 200 dpa and a sufficient irradiation volume (500 cm{sup 3}) for testing the candidate materials and components up to about a full lifetime of their anticipated use in ITER and DEMO. To realize such a condition, 40 MeV deuteron beam with a current of 250 mA is injected into high speed liquid lithium flow with a speed of 20 m/s. Following Conceptual Design Activity (1995-1998), a design study with focus on cost reduction without changing its original mission has been done in 1999. The following major changes to the CAD target design have been considered in the study and included in the new design: i) number of the Li target has been changed from 2 to 1, ii) spare of impurity traps of the Li loop was removed although the spare will be stored in a laboratory for quick exchange, iii) building volume was reduced via design changes in lithium loop length. This paper describes the reduced cost design of the lithium target system and recent status of Key Element Technology activities. (author)

  1. High-Speed Incoming Infrared Target Detection by Fusion of Spatial and Temporal Detectors

    Science.gov (United States)

    Kim, Sungho

    2015-01-01

    This paper presents a method for detecting high-speed incoming targets by the fusion of spatial and temporal detectors to achieve a high detection rate for an active protection system (APS). The incoming targets have different image velocities according to the target-camera geometry. Therefore, single-target detector-based approaches, such as a 1D temporal filter, 2D spatial filter and 3D matched filter, cannot provide a high detection rate with moderate false alarms. The target speed variation was analyzed according to the incoming angle and target velocity. The speed of the distant target at the firing time is almost stationary and increases slowly. The speed varying targets are detected stably by fusing the spatial and temporal filters. The stationary target detector is activated by an almost zero temporal contrast filter (TCF) and identifies targets using a spatial filter called the modified mean subtraction filter (M-MSF). A small motion (sub-pixel velocity) target detector is activated by a small TCF value and finds targets using the same spatial filter. A large motion (pixel-velocity) target detector works when the TCF value is high. The final target detection is terminated by fusing the three detectors based on the threat priority. The experimental results of the various target sequences show that the proposed fusion-based target detector produces the highest detection rate with an acceptable false alarm rate. PMID:25815448

  2. Fusion Energy Division: Annual progress report, period ending December 31, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, O.B. Jr.; Berry, L.A.; Sheffield, J.

    1988-11-01

    The Fusion Program of Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, carries out research in nearly all areas of magnetic fusion. Collaboration among staff from ORNL, Martin Marietta Energy Systems, Inc., private industry, the academic community, and other fusion laboratories, in the United States and abroad, is directed toward the development of fusion as an energy source. This report documents the program's achievements during 1987. Issued as the annual progress report of the ORNL Fusion Energy Division, it also contains information from components of the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts, engineering and physics of existing and planned devices, development and testing of diagnostic tools and techniques in support of experiments, assembly and distribution to the fusion community of databases on atomic physics and radiation effects, development and testing of technologies for heating and fueling fusion plasmas, development and testing of superconducting magnets for containing fusion plasmas, and development and testing of materials for fusion devices. Highlights from program activities are included in this report. 126 figs., 15 tabs.

  3. Fusion Energy Division progress report, 1 January 1990--31 December 1991

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, J.; Baker, C.C.; Saltmarsh, M.J.

    1994-03-01

    The Fusion Program of the Oak Ridge National Laboratory (ORNL), a major part of the national fusion program, encompasses nearly all areas of magnetic fusion research. The program is directed toward the development of fusion as an economical and environmentally attractive energy source for the future. The program involves staff from ORNL, Martin Marietta Energy systems, Inc., private industry, the academic community, and other fusion laboratories, in the US and abroad. Achievements resulting from this collaboration are documented in this report, which is issued as the progress report of the ORNL Fusion Energy Division; it also contains information from components for the Fusion Program that are external to the division (about 15% of the program effort). The areas addressed by the Fusion Program include the following: experimental and theoretical research on magnetic confinement concepts; engineering and physics of existing and planned devices, including remote handling; development and testing of diagnostic tools and techniques in support of experiments; assembly and distribution to the fusion community of databases on atomic physics and radiation effects; development and testing of technologies for heating and fueling fusion plasmas; development and testing of superconducting magnets for containing fusion plasmas; development and testing of materials for fusion devices; and exploration of opportunities to apply the unique skills, technology, and techniques developed in the course of this work to other areas (about 15% of the Division`s activities). Highlights from program activities during 1990 and 1991 are presented.

  4. Modelling and Simulation of Multi-target Multi-sensor Data Fusion for Trajectory Tracking

    Directory of Open Access Journals (Sweden)

    A.K. Singh

    2009-05-01

    Full Text Available An implementation of track fusion using various algorthims has been demonstrated . The sensor measurements of these targets are modelled using Kalman filter (KF and interacting multiple models (IMM filter. The joint probabilistic data association filter (JPDAF and neural network fusion (NNF algorithms were used for tracking multiple man-euvring targets. Track association and fusion algorithm are executed to get the fused track data for various scenarios, two sensors tracking a single target to three sensors tracking three targets, to evaluate the effects of multiple and dispersed sensors for single target, two targets, and multiple targets. The targets chosen were distantly spaced, closely spaced and crossing. Performance of different filters was compared and fused trajectory is found to be closer to the true target trajectory as compared to that for any of the sensor measurements of that target.Defence Science Journal, 2009, 59(3, pp.205-214, DOI:http://dx.doi.org/10.14429/dsj.59.1513

  5. Low-density hydrocarbon foams for laser fusion targets: Progress report, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Haendler, B.L.; Buckley, S.R.; Chen, C.; Cook, A.R.; Cook, R.C.; Hair, L.M.; Kong, F.M.; Kramer, H.D.; Letts, S.A.; Overturf, G.E. III

    1988-06-01

    This report describes progress made in the development of direct-drive hydrocarbon foam targets for laser inertial confinement fusion during 1987. The foam materials are polystyrene, resorcinol-formaldehyde, carbonized resorcinol-formaldehyde, and cellulose acetate. The processes for making the foams, their properties, characterization techniques, and the relationship of their properties to target specifications are presented. Progress in the creation and testing of prototype targets is also described.

  6. New fusion method offers hope of new energy source

    CERN Multimedia

    Chang, K

    2002-01-01

    Scientists from Sandia National Laboratories have reported that they have acheived thermonuclear fusion using the Z accelerator. It is the first observation of fusion using a pulsed power source (1 page).

  7. Response to FESAC survey, non-fusion connections to Fusion Energy Sciences. Applications of the FES-supported beam and plasma simulation code, Warp

    Energy Technology Data Exchange (ETDEWEB)

    Friedman, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Grote, D. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Vay, J. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-05-29

    The Fusion Energy Sciences Advisory Committee’s subcommittee on non-fusion applications (FESAC NFA) is conducting a survey to obtain information from the fusion community about non-fusion work that has resulted from their DOE-funded fusion research. The subcommittee has requested that members of the community describe recent developments connected to the activities of the DOE Office of Fusion Energy Sciences. Two questions in particular were posed by the subcommittee. This document contains the authors’ responses to those questions.

  8. Fusion Energy Division annual progress report, period ending December 31, 1989

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, J.; Baker, C.C.; Saltmarsh, M.J.

    1991-07-01

    The Fusion Program of Oak Ridge National Laboratory (ORNL) carries out research in most areas of magnetic confinement fusion. The program is directed toward the development of fusion as an energy source and is a strong and vital component of both the US fusion program and the international fusion community. Issued as the annual progress report of the ORNL Fusion Energy Division, this report also contains information from components of the Fusion Program that are carried out by other ORNL organizations (about 15% of the program effort). The areas addressed by the Fusion Program and discussed in this report include the following: Experimental and theoretical research on magnetic confinement concepts, engineering and physics of existing and planned devices, including remote handling, development and testing of diagnostic tools and techniques in support of experiments, assembly and distribution to the fusion community of databases on atomic physics and radiation effects, development and testing of technologies for heating and fueling fusion plasmas, development and testing of superconducting magnets for containing fusion plasmas, development and testing of materials for fusion devices, and exploration of opportunities to apply the unique skills, technology, and techniques developed in the course of this work to other areas. Highlights from program activities are included in this report.

  9. Algorithm for Multi-laser-target Tracking Based on Clustering Fusion

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-qun; LI Yan-jun; ZHANG Ke

    2007-01-01

    Multi-laser-target tracking is an important subject in the field of signal processing of laser warners. A clustering method is applied to the measurement of laser warner, and the space-time fusion for measurements in the same cluster is accomplished. Real-time tracking of multi-laser-target and real-time picking of multi-laser-signal are introduced using data fusion of the measurements. A prototype device of the algorithm is built up. The results of experiments show that the algorithm is very effective.

  10. EU Energy Policies Targeting the Environment

    Directory of Open Access Journals (Sweden)

    PAUL CALANTER

    2014-05-01

    Full Text Available Activities in the energy sector provide the greatest contribution to the emission of greenhouse gases (GHG, which are assigned primary responsibility for producing climate change. The European Union puts great emphasis on the mitigation of the environmental impact of the energy sector, in particular concerning the combat against climate change, this fact being demonstrated by the implementation of policies by the EU in this field. This paper aims to analyse the most important Community energy policies with environmental effects, such as setting of climate and energy targets for 2030, policies on nuclear and renewable energy or measures to increase energy efficiency.

  11. Radiation Hydrodynamic Parameter Study of Inertial Fusion Energy Reactor Chambers

    Science.gov (United States)

    Sacks, Ryan; Moses, Gregory

    2014-10-01

    Inertial fusion energy reactors present great promise for the future as they are capable of providing baseline power with no carbon footprint. Simulation work regarding the chamber response and first wall insult is performed with the 1-D radiation hydrodynamics code BUCKY. Simulation with differing chamber parameters are implemented to study the effect of gas fill, gas mixtures and chamber radii. Xenon and argon gases are of particular interest as shielding for the first wall due to their high opacity values and ready availability. Mixing of the two gases is an attempt to engineer a gas cocktail to provide the maximum amount of shielding with the least amount of cost. A parameter study of different chamber radii shows a consistent relationship with that of first wall temperature (~1/r2) and overpressure (~1/r3). This work is performed under collaboration with Lawrence Livermore National Laboratory.

  12. Target debris collection studies for inertial confinement fusion (ICF) experiments

    Science.gov (United States)

    Grim, G. P.; Archuleta, T. N.; Bradley, P. A.; Fowler, M. M.; Hayes, A. C.; Jungman, G.; Obst, A. W.; Rundberg, R. S.; Vieira, D. J.; Wang, Y. Q.; Wilhelmy, J. B.

    2010-08-01

    At the recently completed National Ignition Facility (NIF) at Lawrence Livermore National Laboratory, the initial set of diagnostics to be deployed are focused on measuring neutrons and γ's generated by d(t,n)α reactions in the imploded capsule. Although valuable for understanding pre-ignition experiments, this abbreviated diagnostic suite provides an incomplete picture of the plasma conditions obtained. Prompt radiochemical techniques, based on induced neutron and charged particle reactions within the imploded target, provide a novel and interesting new perspective. To enable these techniques requires the collection and assay of activated target material. In Nov. 2008, experiments were performed using the Omega Laser at the University of Rochester to study the efficiency of collecting debris from directly driven targets. Results from these experiments indicate that target debris was successfully collected, and the debris thermalization and transport scheme enhanced the debris collection up to 347% over direct collection.

  13. Target debris collection studies for inertial confinement fusion (ICF) experiments

    Energy Technology Data Exchange (ETDEWEB)

    Grim, G P; Archuleta, T N; Bradley, P A; Fowler, M M; Hayes, A C; Jungman, G; Obst, A W; Rundberg, R S; Vieira, D J; Wang, Y Q; Wilhelmy, J B, E-mail: gpgrim@lanl.go [Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545 (United States)

    2010-08-01

    At the recently completed National Ignition Facility (NIF) at Lawrence Livermore National Laboratory, the initial set of diagnostics to be deployed are focused on measuring neutrons and {gamma}'s generated by d(t,n){alpha} reactions in the imploded capsule. Although valuable for understanding pre-ignition experiments, this abbreviated diagnostic suite provides an incomplete picture of the plasma conditions obtained. Prompt radiochemical techniques, based on induced neutron and charged particle reactions within the imploded target, provide a novel and interesting new perspective. To enable these techniques requires the collection and assay of activated target material. In Nov. 2008, experiments were performed using the Omega Laser at the University of Rochester to study the efficiency of collecting debris from directly driven targets. Results from these experiments indicate that target debris was successfully collected, and the debris thermalization and transport scheme enhanced the debris collection up to 347% over direct collection.

  14. MRI-PET image fusion based on NSCT transform using local energy and local variance fusion rules.

    Science.gov (United States)

    Amini, Nasrin; Fatemizadeh, E; Behnam, Hamid

    2014-05-01

    Image fusion means to integrate information from one image to another image. Medical images according to the nature of the images are divided into structural (such as CT and MRI) and functional (such as SPECT, PET). This article fused MRI and PET images and the purpose is adding structural information from MRI to functional information of PET images. The images decomposed with Nonsubsampled Contourlet Transform and then two images were fused with applying fusion rules. The coefficients of the low frequency band are combined by a maximal energy rule and coefficients of the high frequency bands are combined by a maximal variance rule. Finally, visual and quantitative criteria were used to evaluate the fusion result. In visual evaluation the opinion of two radiologists was used and in quantitative evaluation the proposed fusion method was compared with six existing methods and used criteria were entropy, mutual information, discrepancy and overall performance.

  15. Laser inertial fusion-based energy: Neutronic design aspects of a hybrid fusion-fission nuclear energy system

    Science.gov (United States)

    Kramer, Kevin James

    This study investigates the neutronics design aspects of a hybrid fusion-fission energy system called the Laser Fusion-Fission Hybrid (LFFH). A LFFH combines current Laser Inertial Confinement fusion technology with that of advanced fission reactor technology to produce a system that eliminates many of the negative aspects of pure fusion or pure fission systems. When examining the LFFH energy mission, a significant portion of the United States and world energy production could be supplied by LFFH plants. The LFFH engine described utilizes a central fusion chamber surrounded by multiple layers of multiplying and moderating media. These layers, or blankets, include coolant plenums, a beryllium (Be) multiplier layer, a fertile fission blanket and a graphite-pebble reflector. Each layer is separated by perforated oxide dispersion strengthened (ODS) ferritic steel walls. The central fusion chamber is surrounded by an ODS ferritic steel first wall. The first wall is coated with 250-500 mum of tungsten to mitigate x-ray damage. The first wall is cooled by Li17Pb83 eutectic, chosen for its neutron multiplication and good heat transfer properties. The Li17Pb 83 flows in a jacket around the first wall to an extraction plenum. The main coolant injection plenum is immediately behind the Li17Pb83, separated from the Li17Pb83 by a solid ODS wall. This main system coolant is the molten salt flibe (2LiF-BeF2), chosen for beneficial neutronics and heat transfer properties. The use of flibe enables both fusion fuel production (tritium) and neutron moderation and multiplication for the fission blanket. A Be pebble (1 cm diameter) multiplier layer surrounds the coolant injection plenum and the coolant flows radially through perforated walls across the bed. Outside the Be layer, a fission fuel layer comprised of depleted uranium contained in Tristructural-isotropic (TRISO) fuel particles having a packing fraction of 20% in 2 cm diameter fuel pebbles. The fission blanket is cooled by

  16. Binding and Fusion of Extracellular Vesicles to the Plasma Membrane of Their Cell Targets.

    Science.gov (United States)

    Prada, Ilaria; Meldolesi, Jacopo

    2016-08-09

    Exosomes and ectosomes, extracellular vesicles of two types generated by all cells at multivesicular bodies and the plasma membrane, respectively, play critical roles in physiology and pathology. A key mechanism of their function, analogous for both types of vesicles, is the fusion of their membrane to the plasma membrane of specific target cells, followed by discharge to the cytoplasm of their luminal cargo containing proteins, RNAs, and DNA. Here we summarize the present knowledge about the interactions, binding and fusions of vesicles with the cell plasma membrane. The sequence initiates with dynamic interactions, during which vesicles roll over the plasma membrane, followed by the binding of specific membrane proteins to their cell receptors. Membrane binding is then converted rapidly into fusion by mechanisms analogous to those of retroviruses. Specifically, proteins of the extracellular vesicle membranes are structurally rearranged, and their hydrophobic sequences insert into the target cell plasma membrane which undergoes lipid reorganization, protein restructuring and membrane dimpling. Single fusions are not the only process of vesicle/cell interactions. Upon intracellular reassembly of their luminal cargoes, vesicles can be regenerated, released and fused horizontally to other target cells. Fusions of extracellular vesicles are relevant also for specific therapy processes, now intensely investigated.

  17. TIMELY DELIVERY OF LASER INERTIAL FUSION ENERGY (LIFE)

    Energy Technology Data Exchange (ETDEWEB)

    Dunne, A M

    2010-11-30

    The National Ignition Facility (NIF), the world's largest and most energetic laser system, is now operational at Lawrence Livermore National Laboratory. A key goal of the NIF is to demonstrate fusion ignition for the first time in the laboratory. Its flexibility allows multiple target designs (both indirect and direct drive) to be fielded, offering substantial scope for optimization of a robust target design. In this paper we discuss an approach to generating gigawatt levels of electrical power from a laser-driven source of fusion neutrons based on these demonstration experiments. This 'LIFE' concept enables rapid time-to-market for a commercial power plant, assuming success with ignition and a technology demonstration program that links directly to a facility design and construction project. The LIFE design makes use of recent advances in diode-pumped, solid-state laser technology. It adopts the paradigm of Line Replaceable Units utilized on the NIF to provide high levels of availability and maintainability and mitigate the need for advanced materials development. A demonstration LIFE plant based on these design principles is described, along with the areas of technology development required prior to plant construction. A goal-oriented, evidence-based approach has been proposed to allow LIFE power plant rollout on a time scale that meets policy imperatives and is consistent with utility planning horizons. The system-level delivery builds from our prior national investment over many decades and makes full use of the distributed capability in laser technology, the ubiquity of semiconductor diodes, high volume manufacturing markets, and U.S. capability in fusion science and nuclear engineering. The LIFE approach is based on the ignition evidence emerging from NIF and adopts a line-replaceable unit approach to ensure high plant availability and to allow evolution from available technologies and materials. Utilization of a proven physics platform for the

  18. TIMELY DELIVERY OF LASER INERTIAL FUSION ENERGY (LIFE)

    Energy Technology Data Exchange (ETDEWEB)

    Dunne, A M

    2010-11-30

    The National Ignition Facility (NIF), the world's largest and most energetic laser system, is now operational at Lawrence Livermore National Laboratory. A key goal of the NIF is to demonstrate fusion ignition for the first time in the laboratory. Its flexibility allows multiple target designs (both indirect and direct drive) to be fielded, offering substantial scope for optimization of a robust target design. In this paper we discuss an approach to generating gigawatt levels of electrical power from a laser-driven source of fusion neutrons based on these demonstration experiments. This 'LIFE' concept enables rapid time-to-market for a commercial power plant, assuming success with ignition and a technology demonstration program that links directly to a facility design and construction project. The LIFE design makes use of recent advances in diode-pumped, solid-state laser technology. It adopts the paradigm of Line Replaceable Units utilized on the NIF to provide high levels of availability and maintainability and mitigate the need for advanced materials development. A demonstration LIFE plant based on these design principles is described, along with the areas of technology development required prior to plant construction. A goal-oriented, evidence-based approach has been proposed to allow LIFE power plant rollout on a time scale that meets policy imperatives and is consistent with utility planning horizons. The system-level delivery builds from our prior national investment over many decades and makes full use of the distributed capability in laser technology, the ubiquity of semiconductor diodes, high volume manufacturing markets, and U.S. capability in fusion science and nuclear engineering. The LIFE approach is based on the ignition evidence emerging from NIF and adopts a line-replaceable unit approach to ensure high plant availability and to allow evolution from available technologies and materials. Utilization of a proven physics platform for the

  19. The potential of imposed magnetic fields for enhancing ignition probability and fusion energy yield in indirect-drive inertial confinement fusion

    Science.gov (United States)

    Perkins, L. J.; Ho, D. D.-M.; Logan, B. G.; Zimmerman, G. B.; Rhodes, M. A.; Strozzi, D. J.; Blackfield, D. T.; Hawkins, S. A.

    2017-06-01

    We examine the potential that imposed magnetic fields of tens of Tesla that increase to greater than 10 kT (100 MGauss) under implosion compression may relax the conditions required for ignition and propagating burn in indirect-drive inertial confinement fusion (ICF) targets. This may allow the attainment of ignition, or at least significant fusion energy yields, in presently performing ICF targets on the National Ignition Facility (NIF) that today are sub-marginal for thermonuclear burn through adverse hydrodynamic conditions at stagnation [Doeppner et al., Phys. Rev. Lett. 115, 055001 (2015)]. Results of detailed two-dimensional radiation-hydrodynamic-burn simulations applied to NIF capsule implosions with low-mode shape perturbations and residual kinetic energy loss indicate that such compressed fields may increase the probability for ignition through range reduction of fusion alpha particles, suppression of electron heat conduction, and potential stabilization of higher-mode Rayleigh-Taylor instabilities. Optimum initial applied fields are found to be around 50 T. Given that the full plasma structure at capsule stagnation may be governed by three-dimensional resistive magneto-hydrodynamics, the formation of closed magnetic field lines might further augment ignition prospects. Experiments are now required to further assess the potential of applied magnetic fields to ICF ignition and burn on NIF.

  20. Fusion studies with low-intensity radioactive ion beams using an active-target time projection chamber

    Energy Technology Data Exchange (ETDEWEB)

    Kolata, J.J., E-mail: jkolata@nd.edu [Physics Department, University of Notre Dame, Notre Dame, IN 46556 (United States); Howard, A.M. [Physics Department, University of Notre Dame, Notre Dame, IN 46556 (United States); Mittig, W. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Ahn, T. [Physics Department, University of Notre Dame, Notre Dame, IN 46556 (United States); Bazin, D. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Becchetti, F.D. [Physics Department, University of Michigan, Ann Arbor, MI 48109 (United States); Beceiro-Novo, S.; Chajecki, Z. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Febbrarro, M. [Physics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Fritsch, A.; Lynch, W.G. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Roberts, A. [Physics Department, University of Notre Dame, Notre Dame, IN 46556 (United States); Shore, A. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Torres-Isea, R.O. [Physics Department, University of Michigan, Ann Arbor, MI 48109 (United States)

    2016-09-11

    The total fusion excitation function for {sup 10}Be+{sup 40}Ar has been measured over the center-of-momentum (c.m.) energy range from 12 to 24 MeV using a time-projection chamber (TPC). The main purpose of this experiment, which was carried out in a single run of duration 90 h using a ≈100 particle per second (pps) {sup 10}Be beam, was to demonstrate the capability of an active-target TPC to determine fusion excitation functions for extremely weak radioactive ion beams. Cross sections as low as 12 mb were measured with acceptable (50%) statistical accuracy. It also proved to be possible to separate events in which charged particles were emitted from the fusion residue from those in which only neutrons were evaporated. The method permits simultaneous measurement of incomplete fusion, break-up, scattering, and transfer reactions, and therefore fully exploits the opportunities presented by the very exotic beams that will be available from the new generation of radioactive beam facilities.

  1. Ray-Based Calculations of Backscatter in Laser Fusion Targets

    Energy Technology Data Exchange (ETDEWEB)

    Strozzi, D J; Williams, E A; Hinkel, D E; Froula, D H; London, R A; Callahan, D A

    2008-02-26

    A steady-state model for Brillouin and Raman backscatter along a laser ray path is presented. The daughter plasma waves are treated in the strong damping limit, and have amplitudes given by the (linear) kinetic response to the ponderomotive drive. Pump depletion, inverse-bremsstrahlung damping, bremsstrahlung emission, Thomson scattering off density fluctuations, and whole-beam focusing are included. The numerical code deplete, which implements this model, is described. The model is compared with traditional linear gain calculations, as well as 'plane-wave' simulations with the paraxial propagation code pf3d. Comparisons with Brillouin-scattering experiments at the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, p. 495 (1997)] show that laser speckles greatly enhance the reflectivity over the deplete results. An approximate upper bound on this enhancement, motivated by phase conjugation, is given by doubling the deplete coupling coefficient. Analysis with deplete of an ignition design for the National Ignition Facility (NIF) [J. A. Paisner, E. M. Campbell, and W. J. Hogan, Fusion Technol. 26, p. 755 (1994)], with a peak radiation temperature of 285 eV, shows encouragingly low reflectivity. Doubling the coupling to bound the speckle enhancement suggests a less optimistic picture. Re-absorption of Raman light is seen to be significant in this design.

  2. Opportunities in the Fusion Energy Sciences Program [Includes Appendix C: Topical Areas Characterization

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-06-01

    Recent years have brought dramatic advances in the scientific understanding of fusion plasmas and in the generation of fusion power in the laboratory. Today, there is little doubt that fusion energy production is feasible. The challenge is to make fusion energy practical. As a result of the advances of the last few years, there are now exciting opportunities to optimize fusion systems so that an attractive new energy source will be available when it may be needed in the middle of the next century. The risk of conflicts arising from energy shortages and supply cutoffs, as well as the risk of severe environmental impacts from existing methods of energy production, are among the reasons to pursue these opportunities.

  3. Opportunities in the Fusion Energy Sciences Program. Appendix C: Topical Areas Characterization

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-06-30

    Recent years have brought dramatic advances in the scientific understanding of fusion plasmas and in the generation of fusion power in the laboratory. Today, there is little doubt that fusion energy production is feasible. The challenge is to make fusion energy practical. As a result of the advances of the last few years, there are now exciting opportunities to optimize fusion systems so that an attractive new energy source will be available when it may be needed in the middle of the next century. The risk of conflicts arising from energy shortages and supply cutoffs, as well as the risk of severe environmental impacts from existing methods of energy production, are among the reasons to pursue these opportunities.

  4. Fusion protein vaccines targeting two tumor antigens generate synergistic anti-tumor effects.

    Directory of Open Access Journals (Sweden)

    Wen-Fang Cheng

    Full Text Available INTRODUCTION: Human papillomavirus (HPV has been consistently implicated in causing several kinds of malignancies, and two HPV oncogenes, E6 and E7, represent two potential target antigens for cancer vaccines. We developed two fusion protein vaccines, PE(ΔIII/E6 and PE(ΔIII/E7 by targeting these two tumor antigens to test whether a combination of two fusion proteins can generate more potent anti-tumor effects than a single fusion protein. MATERIALS AND METHODS: In vivo antitumor effects including preventive, therapeutic, and antibody depletion experiments were performed. In vitro assays including intracellular cytokine staining and ELISA for Ab responses were also performed. RESULTS: PE(ΔIII/E6+PE(ΔIII/E7 generated both stronger E6 and E7-specific immunity. Only 60% of the tumor protective effect was observed in the PE(ΔIII/E6 group compared to 100% in the PE(ΔIII/E7 and PE(ΔIII/E6+PE(ΔIII/E7 groups. Mice vaccinated with the PE(ΔIII/E6+PE(ΔIII/E7 fusion proteins had a smaller subcutaneous tumor size than those vaccinated with PE(ΔIII/E6 or PE(ΔIII/E7 fusion proteins alone. CONCLUSION: Fusion protein vaccines targeting both E6 and E7 tumor antigens generated more potent immunotherapeutic effects than E6 or E7 tumor antigens alone. This novel strategy of targeting two tumor antigens together can promote the development of cancer vaccines and immunotherapy in HPV-related malignancies.

  5. Fusion Protein Vaccines Targeting Two Tumor Antigens Generate Synergistic Anti-Tumor Effects

    Science.gov (United States)

    Cheng, Wen-Fang; Chang, Ming-Cheng; Sun, Wei-Zen; Jen, Yu-Wei; Liao, Chao-Wei; Chen, Yun-Yuan; Chen, Chi-An

    2013-01-01

    Introduction Human papillomavirus (HPV) has been consistently implicated in causing several kinds of malignancies, and two HPV oncogenes, E6 and E7, represent two potential target antigens for cancer vaccines. We developed two fusion protein vaccines, PE(ΔIII)/E6 and PE(ΔIII)/E7 by targeting these two tumor antigens to test whether a combination of two fusion proteins can generate more potent anti-tumor effects than a single fusion protein. Materials and Methods In vivo antitumor effects including preventive, therapeutic, and antibody depletion experiments were performed. In vitro assays including intracellular cytokine staining and ELISA for Ab responses were also performed. Results PE(ΔIII)/E6+PE(ΔIII)/E7 generated both stronger E6 and E7-specific immunity. Only 60% of the tumor protective effect was observed in the PE(ΔIII)/E6 group compared to 100% in the PE(ΔIII)/E7 and PE(ΔIII)/E6+PE(ΔIII)/E7 groups. Mice vaccinated with the PE(ΔIII)/E6+PE(ΔIII)/E7 fusion proteins had a smaller subcutaneous tumor size than those vaccinated with PE(ΔIII)/E6 or PE(ΔIII)/E7 fusion proteins alone. Conclusion Fusion protein vaccines targeting both E6 and E7 tumor antigens generated more potent immunotherapeutic effects than E6 or E7 tumor antigens alone. This novel strategy of targeting two tumor antigens together can promote the development of cancer vaccines and immunotherapy in HPV-related malignancies. PMID:24058440

  6. Optimization of Automatic Target Recognition with a Reject Option Using Fusion and Correlated Sensor Data

    Science.gov (United States)

    2005-04-25

    ROC curve in the evaluation of machine learning algorithms,” Pattern Recognition, Vol 30, No 7: 1145-1159 (1997). Brown, Gerald G. “Top Ten Secrets...Kuo C. and Karp , Sherman. “Polarimetric fusion for synthetic aperture radar target classification,” Pattern Recognition, Vol 30, No 5: 769-775

  7. GAMMA-RAY DIAGNOSTICS OF ALPHA-SLOWING IN INERTIAL CONFINEMENT FUSION-TARGETS

    NARCIS (Netherlands)

    DENDOOVEN, PG; DRAKE, RP; CABLE, MD; Dendooven, Peter

    1993-01-01

    For large inertial confinement fusion deuterium-tritium targets, a way to diagnose alpha slowing might be via capture reaction gamma rays. Calculations are presented for two such methods: one uses the alpha+T direct capture gamma rays, the other is based on a series of resonant alpha-capture reactio

  8. GAMMA-RAY DIAGNOSTICS OF ALPHA-SLOWING IN INERTIAL CONFINEMENT FUSION-TARGETS

    NARCIS (Netherlands)

    DENDOOVEN, PG; DRAKE, RP; CABLE, MD; Dendooven, Peter

    1993-01-01

    For large inertial confinement fusion deuterium-tritium targets, a way to diagnose alpha slowing might be via capture reaction gamma rays. Calculations are presented for two such methods: one uses the alpha+T direct capture gamma rays, the other is based on a series of resonant alpha-capture

  9. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1995--September 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Hoppe, M. [ed.

    1997-02-01

    On December 30, 1990, the U.S. Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. In September 1995 this contract ended and a second contract was issued for us to continue this ICF target support work. This report documents the technical activities of the period October 1, 1995 through September 30, 1996. During this period, GA and our partners WJ Schafer Associates (WJSA) and Soane Technologies, Inc. (STI) were assigned 14 formal tasks in support of the Inertial Confinement Fusion program and its five laboratories. A portion of the effort on these tasks included providing direct {open_quotes}Onsite Support{close_quotes} at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). We fabricated and delivered over 800 gold-plated hohlraum mandrels to LLNL, LANL and SNLA. We produced nearly 1,200 glass and plastic target capsules for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). We also delivered over 100 flat foil targets for Naval Research Lab (NRL) and SNLA in FY96. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require capsules containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. We are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Substantial progress has been made on ways to both create and characterize viable layers. During FY96, significant progress was made in the design of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA.

  10. Cluster-based centralized data fusion for tracking maneuvering targets using interacting multiple model algorithm

    Indian Academy of Sciences (India)

    V Vaidehi; K Kalavidya; S Indira Gandhi

    2004-04-01

    The interacting multiple model (IMM) algorithm has proved to be useful in tracking maneuvering targets. Tracking accuracy can be further improved using data fusion. Tracking of multiple targets using multiple sensors and fusing them at a central site using centralized architecture involves communication of large volumes of measurements to a common site. This results in heavy processing requirement at the central site. Moreover, track updates have to be obtained in the fusion centre before the next measurement arrives. For solving this computational complexity, a cluster-based parallel processing solution is presented in this paper. In this scheme, measurements are sent to the data fusion centre where the measurements are partitioned and given to the slave processors in the cluster. The slave processors use the IMM algorithm to get accurate updates of the tracks. The master processor collects the updated tracks and performs data fusion using ‘weight decision approach’. The improvement in the computation time using clusters in the data fusion centre is presented in this paper.

  11. Digital image fusion systems: color imaging and low-light targets

    Science.gov (United States)

    Estrera, Joseph P.

    2009-05-01

    This paper presents digital image fusion (enhanced A+B) systems in color imaging and low light target applications. This paper will discuss first the digital sensors that are utilized in the noted image fusion applications which is a 1900x1086 (high definition format) CMOS imager coupled to a Generation III image intensifier for the visible/near infrared (NIR) digital sensor and 320x240 or 640x480 uncooled microbolometer thermal imager for the long wavelength infrared (LWIR) digital sensor. Performance metrics for these digital imaging sensors will be presented. The digital image fusion (enhanced A+B) process will be presented in context of early fused night vision systems such as the digital image fused system (DIFS) and the digital enhanced night vision goggle and later, the long range digitally fused night vision sighting system. Next, this paper will discuss the effects of user display color in a dual color digital image fusion system. Dual color image fusion schemes such as Green/Red, Cyan/Yellow, and White/Blue for image intensifier and thermal infrared sensor color representation, respectively, are discussed. Finally, this paper will present digitally fused imagery and image analysis of long distance targets in low light from these digital fused systems. The result of this image analysis with enhanced A+B digital image fusion systems is that maximum contrast and spatial resolution is achieved in a digital fusion mode as compared to individual sensor modalities in low light, long distance imaging applications. Paper has been cleared by DoD/OSR for Public Release under Ref: 08-S-2183 on August 8, 2008.

  12. Using Thin Film Targets for Muonic Atoms and Muon Catalyzed Fusion Studies

    CERN Document Server

    Fujiwara, M C; Bailey, J M; Beer, G A; Beveridge, J L; Faifman, M P; Huber, T M; Kammel, P; Kim, S K; Knowles, P E; Kunselman, A R; Markushin, V E; Marshall, G M; Martoff, C J; Mason, G R; Mulhauser, F; Olin, A; Petitjean, C; Porcelli, T A; Zmeskal, J

    2000-01-01

    Studies of muonic atoms and muon catalyzed fusion have been conventionally done in a bulk target of gas, liquid or solid hydrogen isotopes. The use of thin film targets developed at TRIUMF have notable advantages in tackling some of the most important questions in the field, which could be further exploited at future high intensity muon sources. We review the technique of the thin film method with emphasis on recent results and a future proposal.

  13. Computational Complexity Comparison Of Multi-Sensor Single Target Data Fusion Methods By Matlab

    OpenAIRE

    Hoseini, Sayed Amir; Ashraf, Mohammad Reza

    2013-01-01

    Target tracking using observations from multiple sensors can achieve better estimation performance than a single sensor. The most famous estimation tool in target tracking is Kalman filter. There are several mathematical approaches to combine the observations of multiple sensors by use of Kalman filter. An important issue in applying a proper approach is computational complexity. In this paper, four data fusion algorithms based on Kalman filter are considered including three centralized and o...

  14. Continuum fusion solutions for replacement target models in electro-optic detection.

    Science.gov (United States)

    Schaum, Alan

    2014-05-01

    The additive target model is used routinely in the statistical detection of opaque targets, despite its phenomenological inaccuracy. The more appropriate replacement target model is seldom used, because the standard method for producing a detection algorithm from it proves to be intractable, unless narrow restrictions are imposed. Now, the recently developed continuum fusion (CF) methodology allows an expanded solution set to the general replacement target problem. It also provides a mechanism for producing approximate solutions for the standard approach. We illustrate the principles of CF by using them to generate both types of answers for the correct detection model.

  15. Objective evaluation of target detectability in night vision color fusion images

    Institute of Scientific and Technical Information of China (English)

    Yihui Yuan; Junju Zhang; Benkang Chang; Hui Xu; Yiyong Han

    2011-01-01

    An evaluation for objectively assessing the target detectability in night vision color fusion images is proposed. On the assumption that target detectability could be modeled as the perceptual color variation between the target and its optimal sensitive background region, we propose an objective target detectability metric in CIELAB color space defined by four color information features: target luminance, region perceptual luminance variation in human vision system, region hue difference, and region chroma difference.Experimental results show that this proposed metric is perceptually meaningful because it corresponds well with subjective evaluation.%@@ An evaluation for objectively assessing the target detectability in night vision color fusion images is proposed. On the assumption that target detectability could be modeled as the perceptual color variation between the target and its optimal sensitive background region, we propose an objective target detectability metric in CIELAB color space defined by four color information features: target luminance, region perceptual luminance variation in human vision system, region hue difference, and region chroma difference.Experimental results show that this proposed metric is perceptually meaningful because it corresponds well with subjective evaluation.

  16. Neutron Transport and Nuclear Burnup Analysis for the Laser Inertial Confinement Fusion-Fission Energy (LIFE) Engine

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, K J; Latkowski, J F; Abbott, R P; Boyd, J K; Powers, J J; Seifried, J E

    2008-10-24

    Lawrence Livermore National Laboratory is currently developing a hybrid fusion-fission nuclear energy system, called LIFE, to generate power and burn nuclear waste. We utilize inertial confinement fusion to drive a subcritical fission blanket surrounding the fusion chamber. It is composed of TRISO-based fuel cooled by the molten salt flibe. Low-yield (37.5 MJ) targets and a repetition rate of 13.3 Hz produce a 500 MW fusion source that is coupled to the subcritical blanket, which provides an additional gain of 4-8, depending on the fuel. In the present work, we describe the neutron transport and nuclear burnup analysis. We utilize standard analysis tools including, the Monte Carlo N-Particle (MCNP) transport code, ORIGEN2 and Monteburns to perform the nuclear design. These analyses focus primarily on a fuel composed of depleted uranium not requiring chemical reprocessing or enrichment. However, other fuels such as weapons grade plutonium and highly-enriched uranium are also under consideration. In addition, we have developed a methodology using {sup 6}Li as a burnable poison to replace the tritium burned in the fusion targets and to maintain constant power over the lifetime of the engine. The results from depleted uranium analyses suggest up to 99% burnup of actinides is attainable while maintaining full power at 2GW for more than five decades.

  17. Ion beam requirements for fast ignition of inertial fusion targets

    CERN Document Server

    Honrubia, J J

    2015-01-01

    Ion beam requirements for fast ignition are investigated by numerical simulation taking into account new effects such as ion beam divergence not included before. We assume that ions are generated by the TNSA scheme in a curved foil placed inside a re-entrant cone and focused on the cone apex or beyond. From the focusing point to the compressed core ions propagate with a given divergence angle. Ignition energies are obtained for two compressed fuel configurations heated by proton and carbon ion beams. The dependence of the ignition energies on the beam divergence angle and on the position of the ion beam focusing point have been analysed. Comparison between TNSA and quasi-monoenergetic ions is also shown.

  18. Developing a plasma focus research training system for the fusion energy age

    Science.gov (United States)

    Lee, S.

    2014-08-01

    The 3 kJ UNU/ICTP Plasma Focus Facility is the most significant device associated with the AAAPT (Asian African Association for Plasma Training). In original and modified/upgraded form it has trained generations of plasma focus (PF) researchers internationally, producing many PhD theses and peer-reviewed papers. The Lee Model code was developed for the design of this PF. This code has evolved to cover all PF machines for design, interpretation and optimization, for derivation of radiation scaling laws; and to provide insights into yield scaling limitations, radiative collapse, speed-enhanced and current-stepped PF variants. As example of fresh perspectives derivable from this code, this paper presents new results on energy transfers of the axial and radial phases of generalized PF devices. As the world moves inexorably towards the Fusion Energy Age it becomes ever more important to train plasma fusion researchers. A recent workshop in Nepal shows that demand for such training continues. Even commercial project development consultants are showing interest. We propose that the AAAPT-proven research package be upgraded, by modernizing the small PF for extreme modes of operation, switchable from the typical strong-focus mode to a slow-mode which barely pinches, thus producing a larger, more uniform plasma stream with superior deposition properties. Such a small device would be cost-effective and easily duplicated, and have the versatility of a range of experiments from intense multi-radiation generation and target damage studies to superior advanced-materials deposition. The complementary code is used to reference experiments up to the largest existing machine. This is ideal for studying machine limitations and scaling laws and to suggest new experiments. Such a modernized versatile PF machine complemented by the universally versatile code would extend the utility of the PF experience; so that AAAPT continues to provide leadership in pulsed plasma research training in

  19. How does incomplete fusion show up at slightly above barrier energies?

    Directory of Open Access Journals (Sweden)

    Prasad R.

    2012-02-01

    Full Text Available Experimental results on the onset of incomplete fusion at slightly above barrier energies are discussed in this paper. Spin-distributions of evaporation residues populated via complete and/or incomplete fusion of 12C,16O (Elab ≈ 4–7 MeV with 169Tm have been measured to probe associated ℓ–values. Particle (Z=1,2 – γ – coincidence technique has been used for channel selection. Entirely different entry state spin populations have been observed during the de-excitation of complete and incomplete composites. The complete fusion residues are found to be strongly fed over a broad spin range. While, a narrow range feeding for only high spin states has been observed in case of incomplete fusion residues. In the present work, incomplete fusion is shown to be a promising tool to populate high spin states in final reaction products. For better insight into the onset and strength of incomplete fusion, the relative contributions of complete and incomplete fusion have been deduced from the analysis of excitation functions and forward recoil ranges. A significant fraction of ICF has been observed even at energy as low as ≈ 7% above the barrier. The relative strengths of complete and incomplete fusion deduced from the analysis of forward-recoil-ranges and excitation functions complement each other. All the available results are discussed in light of the Morgenstern’s mass-asymmetry systematics. Incomplete fusion fraction is found to be large for more mass-asymmetric systems for individual projectiles, which points towards the projectile structure effect on incomplete fusion fraction. Experimentally measured forward ranges of recoils complement the existence of incomplete fusion at slightly above barrier energies, where more than one linear-momentum-transfer components associated with full- and/or partial-fusion of projectile(s have been observed. Present results conclusively demonstrate the possibility to selectively populate high spin states

  20. Hollow glass microsphere production for laser direct-driven fusion targets on Shen Guang II

    Institute of Scientific and Technical Information of China (English)

    QIU; Longhui(邱龙会); FU; Yibei(傅依备); TANG; Yongjian(唐永建); WEI; Yun(魏芸); ZHENG; Yongming(郑永铭); SHI; Tao(师韬); YAO; Shujiu(姚书久)

    2002-01-01

    A liquid-droplet technique was investigated to fabricate thin wall hollow glass microspheres (HGM) used in laser fusion experiments on Shen Guang II. Glass-forming compositions, operating conditions of the droplet generator and the vertical multiple-zone furnace were optimized. Thin wall HGM with diameters of about 100, 200, and 520 μm were fabricated, whose failure pressures, gas retention properties for D2, and chemical durability were all characterized. The results of the fusion experiments show that the HGM targets are quite satisfactory and the highest neutron yields obtained are 4x 109.

  1. Magnetic fusion energy annual report, July 1975--September 1976

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, M.A.; McGregor, C.K.; Gottlieb, L. (eds.)

    1976-12-02

    Supporting research activities continued to provide the technical basis for future mirror-confinement experiments. The industrial development of a high-current, high-field, high-current-density Nb/sub 3/Sn conductor was the main goal of the superconducting magnet program. Beam direct conversion was being developed as a means of raising the efficiency of neutral-beam production, and plasma direct conversion was shown to work as predicted. Conceptual designs were completed for various types of power reactors. The neutral-beam program progressed in three areas: experimental work, facility construction, and conceptual design. Experiments on the 14-MeV Rotating Target Neutron Source (RTNS-II) included participation by experimenters from many different institutions. Methods for processing tritium-contaminated wastes were pursued, as were studies of tritiated methane in stainless-steel vessels, the control of tritium in mirror fusion reactors, and the development of titanium tritide targets for the RTNS. The report period witnessed a rapid maturation in ability to describe theoretically the behavior of ion-cyclotron noise in the 2XIIB and the influence of that noise on the confined plasma. The high beta values achieved in 2XIIB prompted much theoretical analysis of the properties of high-beta equilibria and stability, including those of a field-reversed state. Excellent progress was made on the development of computer codes applicable to magnetic-mirror problems, with emphasis on three-dimensional, finite-beta, guiding-center equilibria, field-reversal, and Fokker-Planck codes.

  2. Soft Fusion Energy Path: Isotope Production in Energy Subcritical/Economy Hypercritical D +D Colliding-Beam Mini Fusion Reactor `Exyder'

    Science.gov (United States)

    Hester, Tim; Maglich, Bogdan; Calsec Collaboration

    2015-03-01

    Bethe1 and Sakharov2 argued for soft fusion energy path via isotope production, substantiated by Manheimer3. - Copious T and 3He production4 , 5 from D(d, p) T and D(d, n) 3He reactions in 725 KeV D +D colliding beams was measured in weak-focusing Self-Collider6 , 7 radius 0.15 m, in B = 3.12 T, non-linearly stabilized by electron cloud oscillations8 to confinement time = 24 s. Simulations6 predict that by switching to strong focusing9, 10 deuterons 0.75 MeV each, generate 1 3He +1T +1p + 1n at total input energy cost 10.72 MeV. Economic value of T and 3He is 65 and 120 MeV/atom, respectively. We obtain economic gain 205MeV/10.72 MeV ~ 2,000% i.e. 3He production funds cost of T. If first wall is made of Thorium n's will breed 233U releasing 200 MeV/fission, at neutron cost 5.36 MeV versus 160 MeV in beam on target, resulting in no cost 3He production, valued 75K/g. 1. Physics Today, May 1979, p.44; 2. Memoirs, Vintage Books, (1992); 3. Phys. Today, May 2012 p. 12; 4. Phys. Rev. Lett. 54, 796 (1985); 5. Bull. APS, 57, No. 3 (2012); 6. Part. Acc.1, (1970); 7. ANEUTRONIC FUSION NIM A 271 1-167 (1988); 8. Phys. Rev. Lett. 70, 1818 (1993); 9. Part. Acc. 34, 13 (1990).

  3. Fusion Energy Division progress report, January 1, 1992--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, J.; Baker, C.C.; Saltmarsh, M.J.; Shannon, T.E.

    1995-09-01

    The report covers all elements of the ORNL Fusion Program, including those implemented outside the division. Non-fusion work within FED, much of which is based on the application of fusion technologies and techniques, is also discussed. The ORNL Fusion Program includes research and development in most areas of magnetic fusion research. The program is directed toward the development of fusion as an energy source and is a strong and vital component of both the US and international fusion efforts. The research discussed in this report includes: experimental and theoretical research on magnetic confinement concepts; engineering and physics of existing and planned devices; development and testing of plasma diagnostic tools and techniques; assembly and distribution of databases on atomic physics and radiation effects; development and testing of technologies for heating and fueling fusion plasmas; and development and testing of materials for fusion devices. The activities involving the use of fusion technologies and expertise for non-fusion applications ranged from semiconductor manufacturing to environmental management.

  4. Study of Fusion Dynamics Using Skyrme Energy Density Formalism with Different Surface Corrections

    Institute of Scientific and Technical Information of China (English)

    Ishwar Dutt; Narinder K. Dhiman

    2010-01-01

    @@ Within the framework of Skyrme energy density formalism, we investigate the role of surface corrections on the fusion of colliding nuclei. The coefficient of surface correction is varied between 1/36 and 4/36, and its impact is studied on about 180 reactions. The detailed investigations indicate a linear relationship between the fusion barrier heights and strength of the surface corrections. Our analysis of the fusion barriers advocate the strength of surface correction of 1/36.

  5. The Fusion Driven Rocket: Nuclear Propulsion through Direct Conversion of Fusion Energy Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Current nuclear fusion efforts have focused on the generation of electric grid power and are wholly inappropriate for space transportation as the application of a...

  6. Investigation of complete and incomplete fusion dynamics of {sup 20}Ne induced reactions at energies above the Coulomb barrier

    Energy Technology Data Exchange (ETDEWEB)

    Singh, D., E-mail: dsinghiuac@gmail.com [Centre for Applied Physics, Central University of Jharkhand, Ranchi-835 205 (India); Ali, R. [Department of Physics, G.F.(P.G.), College, Shahjahanpur-242 001 (India); Kumar, Harish; Ansari, M. Afzal [Department of Physics, Aligarh Muslim University, Aligarh-202 002 (India); Rashid, M. H.; Guin, R. [Variable Energy Cyclotron Centre, 1/AF, Bidhan Nagar, Kolkata-700 064 (India)

    2014-08-14

    Experiment has been performed to explore the complete and incomplete fusion dynamics in heavy ion collisions using stacked foil activation technique. The measurement of excitation functions of the evaporation residues produced in the {sup 20}Ne+{sup 165}Ho system at projectile energies ranges ≈ 4-8 MeV/nucleon have been done. Measured cumulative and direct cross-sections have been compared with the theoretical model code PACE-2, which takes into account only the complete fusion process. The analysis indicates the presence of contributions from incomplete fusion processes in some α-emission channels following the break-up of the projectile {sup 20}Ne in the nuclear field of the target nucleus {sup 165}Ho.

  7. Prostate cancer detection with MR-ultrasound fusion biopsy: the role of systematic and targeted biopsies

    Science.gov (United States)

    Filson, Christopher P.; Natarajan, Shyam; Margolis, Daniel J.A.; Huang, Jiaoti; Lieu, Patricia; Dorey, Frederick J.; Reiter, Robert E.; Marks, Leonard S.

    2015-01-01

    BACKGROUND To evaluate performance of magnetic resonance (MR)-ultrasound guided fusion biopsy in diagnosing clinically significant prostate cancer (csCaP). METHODS 1042 men underwent multi-parametric MRI (mpMRI) and fusion biopsy consecutively in a prospective trial (2009 – 2014). An expert reader graded mpMRI regions of interest (ROI) 1–5 using published protocols. The fusion biopsy device was used to obtain targeted cores from ROIs (when present) followed by a fusion-image guided 12-core systematic biopsy in all men, even if no suspicious ROI. Primary endpoint was detection of clinically significant CaP (i.e., Gleason score ≥ 7). RESULTS Among 825 men with ≥ 1 suspicious ROI of grade 3 or higher, 289 (35%) had csCaP. Powerful predictors of csCaP were ROI grade (grade 5 vs 3, OR 6.5, pbiopsies detected more csCaP (n=289) than targeting (n=229) or systematic biopsy alone (n=199). Among patients with no suspicious ROI, 35 (16%) had csCaP on systematic biopsy. CONCLUSION In this prospective trial, MR-ultrasound fusion biopsy allowed detection of csCaP with a direct relationship with ROI grade and PSA density. The combination of targeted and systematic biopsy detected more csCaP than either modality alone; systematic biopsies revealed csCaP in 16% of men with no suspicious MRI target. Advantages of this new biopsy method are apparent, but issues of cost, training, and reliability await resolution prior to widespread adoption. PMID:26749141

  8. Synthetic Aperture Radar Target Recognition with Feature Fusion Based on a Stacked Autoencoder.

    Science.gov (United States)

    Kang, Miao; Ji, Kefeng; Leng, Xiangguang; Xing, Xiangwei; Zou, Huanxin

    2017-01-20

    Feature extraction is a crucial step for any automatic target recognition process, especially in the interpretation of synthetic aperture radar (SAR) imagery. In order to obtain distinctive features, this paper proposes a feature fusion algorithm for SAR target recognition based on a stacked autoencoder (SAE). The detailed procedure presented in this paper can be summarized as follows: firstly, 23 baseline features and Three-Patch Local Binary Pattern (TPLBP) features are extracted. These features can describe the global and local aspects of the image with less redundancy and more complementarity, providing richer information for feature fusion. Secondly, an effective feature fusion network is designed. Baseline and TPLBP features are cascaded and fed into a SAE. Then, with an unsupervised learning algorithm, the SAE is pre-trained by greedy layer-wise training method. Capable of feature expression, SAE makes the fused features more distinguishable. Finally, the model is fine-tuned by a softmax classifier and applied to the classification of targets. 10-class SAR targets based on Moving and Stationary Target Acquisition and Recognition (MSTAR) dataset got a classification accuracy up to 95.43%, which verifies the effectiveness of the presented algorithm.

  9. Synthetic Aperture Radar Target Recognition with Feature Fusion Based on a Stacked Autoencoder

    Directory of Open Access Journals (Sweden)

    Miao Kang

    2017-01-01

    Full Text Available Feature extraction is a crucial step for any automatic target recognition process, especially in the interpretation of synthetic aperture radar (SAR imagery. In order to obtain distinctive features, this paper proposes a feature fusion algorithm for SAR target recognition based on a stacked autoencoder (SAE. The detailed procedure presented in this paper can be summarized as follows: firstly, 23 baseline features and Three-Patch Local Binary Pattern (TPLBP features are extracted. These features can describe the global and local aspects of the image with less redundancy and more complementarity, providing richer information for feature fusion. Secondly, an effective feature fusion network is designed. Baseline and TPLBP features are cascaded and fed into a SAE. Then, with an unsupervised learning algorithm, the SAE is pre-trained by greedy layer-wise training method. Capable of feature expression, SAE makes the fused features more distinguishable. Finally, the model is fine-tuned by a softmax classifier and applied to the classification of targets. 10-class SAR targets based on Moving and Stationary Target Acquisition and Recognition (MSTAR dataset got a classification accuracy up to 95.43%, which verifies the effectiveness of the presented algorithm.

  10. Advances in HYDRA and its application to simulations of Inertial Confinement Fusion targets

    Science.gov (United States)

    Marinak, M. M.; Kerbel, G. D.; Koning, J. M.; Patel, M. V.; Sepke, S. M.; Brown, P. N.; Chang, B.; Procassini, R.; Veitzer, S. A.

    2008-11-01

    We will outline new capabilities added to the HYDRA 2D/3D multiphysics ICF simulation code. These include a new SN multigroup radiation transport package (1D), constitutive models for elastic-plastic (strength) effects, and a mix model. A Monte Carlo burn package is being incorporated to model diagnostic signatures of neutrons, gamma rays and charged particles. A 3D MHD package that treats resistive MHD is available. Improvements to HYDRA's implicit Monte Carlo photonics package, including the addition of angular biasing, now enable integrated hohlraum simulations to complete in substantially shorter time. The heavy ion beam deposition package now includes a new model for ion stopping power developed by the Tech-X Corporation, with improved accuracy below the Bragg peak. Examples will illustrate HYDRA's enhanced capabilities to simulate various aspects of inertial confinement fusion targets.This work was performed under the auspices of the Lawrence Livermore National Security, LLC, (LLNS) under Contract No. DE-AC52-07NA27344. The work of Tech-X personnel was funded by the Department of Energy under Small Business Innovation Research Contract No. DE-FG02-03ER83797.

  11. Energy dependence of potential barriers and its effect on fusion cross-sections

    CERN Document Server

    Umar, A S; Oberacker, V E

    2014-01-01

    Couplings between relative motion and internal structures are known to affect fusion barriers by dynamically modifying the densities of the colliding nuclei. The effect is expected to be stronger at energies near the barrier top, where changes in density have longer time to develop than at higher energies. Quantitatively, modern TDHF calculations are able to predict realistic fusion thresholds. However, the evolution of the potential barrier with bombarding energy remains to be confronted with the experimental data. The aim is to find signatures of the energy dependence of the barrier by comparing fusion cross-sections calculated from potentials obtained at different bombarding energies with the experimental data. This comparison is made for the $^{40}$Ca+$^{40}$Ca and $^{16}$O+$^{208}$Pb systems. Fusion cross-sections are computed from potentials calculated with the density-constrained TDHF method. The couplings decrease the barrier at low-energy in both cases. A deviation from the Woods-Saxon nuclear potent...

  12. A pathway to laser fusion energy in Japan

    Science.gov (United States)

    Azechi, Hiroshi

    2016-10-01

    High-density compression of DT to one thousand times its liquid density is the critical path of inertial fusion and was demonstrated in Japan and US in late 1980's. The Osaka group has achieved high-density compression that meets one of the critical requirements for thermonuclear ignition and bum. Although the compression densities were well reproduced by computer simulations, the neutron yields were much lower than the simulation predictions by three orders of magnitudes, suggesting catastrophic collapse of a hot spark, from which thermonuclear reactions are triggered. In order to overcome this difficulty the international ICF community has adopted two approaches: one is to generate a larger hot spark than the mixed layer with MJ-Class lasers, such as NIF and LMJ. The other approach is to externally heat the compressed fuel. The second approach is the fast ignition. After the proof-of-concept experiment in 2002, we started the Fast Ignition Realization Experiment (FlREX) project to complete the world most powerful high-energy peta-watt laser "LFEX" as a heating laser.

  13. Developing diagnostic systems for ITER – the next step fusion energy experiment

    DEFF Research Database (Denmark)

    Korsholm, Søren Bang; Leipold, Frank; Gutierrez Espinoza, Heidi Estibaliz

    to be a viable energy source. Fusion energy power plants will be safe and can be operated to supply the baseload of an energy system. The fuel resources are inexhaustible, and can be derived from sea water. Fusion energy is based on the nuclear reaction fusing hydrogen isotopes into helium – like in the Sun......Fusion energy research is moving to the next stage with the well progressed construction of one of the largest research infrastructures ever – ITER. The goal of ITER is to produce 500 MW of fusion power while heating the fuel –deuterium/tritium plasma – by 50 MW. This will confirm fusion energy...... is the ultimate goal of fusion energy, the path towards this is challenging. A fusion plasma has a temperature of 200 mio. degrees (15 times that of the core of the Sun), and this is confined by a magnetic field generated by powerful superconducting magnets in a vacuum chamber of 1000 m3. Operating diagnostic...

  14. Control of fuel target implosion non-uniformity in heavy ion inertial fusion

    CERN Document Server

    Iinuma, T; Kondo, S; Kubo, T; Kato, H; Suzuki, T; Kawata, S; Ogoyski, A I

    2016-01-01

    In inertial fusion, one of scientific issues is to reduce an implosion non-uniformity of a spherical fuel target. The implosion non-uniformity is caused by several factors, including the driver beam illumination non-uniformity, the Rayleigh-Taylor instability (RTI) growth, etc. In this paper we propose a new control method to reduce the implosion non-uniformity; the oscillating implosion acceleration dg(t) is created by pulsating and dephasing heavy ion beams (HIBs) in heavy ion inertial fusion (HIF). The dg(t) would reduce the RTI growth effectively. The original concept of the non- uniformity control in inertial fusion was proposed in (Kawata, et al., 1993). In this paper it was found that the pulsating and dephasing HIBs illumination provide successfully the controlled dg(t) and that dg(t) induced by the pulsating HIBs reduces well the implosion non-uniformity. Consequently the pulsating HIBs improve a pellet gain remarkably in HIF.

  15. Joint sparsity based heterogeneous data-level fusion for target detection and estimation

    Science.gov (United States)

    Niu, Ruixin; Zulch, Peter; Distasio, Marcello; Blasch, Erik; Shen, Dan; Chen, Genshe

    2017-05-01

    Typical surveillance systems employ decision- or feature-level fusion approaches to integrate heterogeneous sensor data, which are sub-optimal and incur information loss. In this paper, we investigate data-level heterogeneous sensor fusion. Since the sensors monitor the common targets of interest, whose states can be determined by only a few parameters, it is reasonable to assume that the measurement domain has a low intrinsic dimensionality. For heterogeneous sensor data, we develop a joint-sparse data-level fusion (JSDLF) approach based on the emerging joint sparse signal recovery techniques by discretizing the target state space. This approach is applied to fuse signals from multiple distributed radio frequency (RF) signal sensors and a video camera for joint target detection and state estimation. The JSDLF approach is data-driven and requires minimum prior information, since there is no need to know the time-varying RF signal amplitudes, or the image intensity of the targets. It can handle non-linearity in the sensor data due to state space discretization and the use of frequency/pixel selection matrices. Furthermore, for a multi-target case with J targets, the JSDLF approach only requires discretization in a single-target state space, instead of discretization in a J-target state space, as in the case of the generalized likelihood ratio test (GLRT) or the maximum likelihood estimator (MLE). Numerical examples are provided to demonstrate that the proposed JSDLF approach achieves excellent performance with near real-time accurate target position and velocity estimates.

  16. Pulse shaping and energy storage capabilities of angularly multiplexed KrF laser fusion drivers

    Science.gov (United States)

    Lehmberg, R. H.; Giuliani, J. L.; Schmitt, A. J.

    2009-07-01

    This paper describes a rep-rated multibeam KrF laser driver design for the 500kJ Inertial Fusion test Facility (FTF) recently proposed by NRL, then models its optical pulse shaping capabilities using the ORESTES laser kinetics code. It describes a stable and reliable iteration technique for calculating the required precompensated input pulse shape that will achieve the desired output shape, even when the amplifiers are heavily saturated. It also describes how this precompensation technique could be experimentally implemented in real time on a reprated laser system. The simulations show that this multibeam system can achieve a high fidelity pulse shaping capability, even for a high gain shock ignition pulse whose final spike requires output intensities much higher than the ˜4MW/cm2 saturation levels associated with quasi-cw operation; i.e., they show that KrF can act as a storage medium even for pulsewidths of ˜1ns. For the chosen pulse, which gives a predicted fusion energy gain of ˜120, the simulations predict the FTF can deliver a total on-target energy of 428kJ, a peak spike power of 385TW, and amplified spontaneous emission prepulse contrast ratios IASE/Ilaser.

  17. Fusion Energy Division annual progress report period ending December 31, 1986

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, O.B. Jr.; Berry, L.A.; Sheffield, J.

    1987-10-01

    This annual report on fusion energy discusses the progress on work in the following main topics: toroidal confinement experiments; atomic physics and plasma diagnostics development; plasma theory and computing; plasma-materials interactions; plasma technology; superconducting magnet development; fusion engineering design center; materials research and development; and neutron transport. (LSP)

  18. Pathway of membrane fusion with two tension-dependent energy barriers

    DEFF Research Database (Denmark)

    Shillcock, Julian C.

    2007-01-01

    Fusion of bilayer membranes is studied via dissipative particle dynamics (DPD) simulations. A new set of DPD parameters is introduced which leads to an energy barrier for flips of lipid molecules between adhering membranes. A large number of fusion events is monitored for a vesicle in contact...

  19. 23rd IAEA Fusion Energy Conference: Summary Of Sessions EX/C and ICC

    Energy Technology Data Exchange (ETDEWEB)

    Hawryluk, R J [PPPL

    2011-01-05

    An overview is given of recent experimental results in the areas of innovative confinement concepts, operational scenarios and confinement experiments as presented at the 2010 IAEA Fusion Energy Conference. Important new findings are presented from fusion devices worldwide, with a strong focus towards the scientific and technical issues associated with ITER and W7-X devices, presently under construction.

  20. Low energy cost for optimal speed and control of membrane fusion.

    Science.gov (United States)

    François-Martin, Claire; Rothman, James E; Pincet, Frederic

    2017-02-07

    Membrane fusion is the cell's delivery process, enabling its many compartments to receive cargo and machinery for cell growth and intercellular communication. The overall activation energy of the process must be large enough to prevent frequent and nonspecific spontaneous fusion events, yet must be low enough to allow it to be overcome upon demand by specific fusion proteins [such as soluble N-ethylmaleimide-sensitive factor attachment protein receptors (SNAREs)]. Remarkably, to the best of our knowledge, the activation energy for spontaneous bilayer fusion has never been measured. Multiple models have been developed and refined to estimate the overall activation energy and its component parts, and they span a very broad range from 20 kBT to 150 kBT, depending on the assumptions. In this study, using a bulk lipid-mixing assay at various temperatures, we report that the activation energy of complete membrane fusion is at the lowest range of these theoretical values. Typical lipid vesicles were found to slowly and spontaneously fully fuse with activation energies of ∼30 kBT Our data demonstrate that the merging of membranes is not nearly as energy consuming as anticipated by many models and is ideally positioned to minimize spontaneous fusion while enabling rapid, SNARE-dependent fusion upon demand.

  1. A Study on Establishing National Technology Strategy of Fusion Energy Development: Combining PEST-SWOT Methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Han Soo; Choi, Won Jae; Tho, Hyun Soo; Kang, Dong Yup; Kim, In Chung [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    Nuclear fusion, the joining of light nuclei of hydrogen into heavier nuclei of helium, has potential environmental, safety and proliferation characteristics as an energy source. It can also, provide an adequate amount of fuel to power civilization for a long time compared to human history. It is, however, more challenging to convert to an energy source than nuclear fission. To overcome this, Korea enacted a law to promote the development of fusion as an energy source in 2007. In accordance with this law, the government will establish a promotion plan to develop fusion energy, including policy goals, a framework, strategies, infrastructure, funding, human resources, international cooperation and etc. This will be reviewed every five years. This paper is focused on the combining PEST (political, economic, social and technological) method with SWOT (strength, weakness, opportunity and threat) analysis, which is a prerequisite to form national fusion energy technology strategy

  2. Application of Preoperative CT/MRI Image Fusion in Target Positioning for Deep Brain Stimulation

    Institute of Scientific and Technical Information of China (English)

    Yu Wang; Zi-yuan Liu; Wan-chen Dou; Wen-bin Ma; Ren-zhi Wang; Yi Guo

    2016-01-01

    Objective To explore the efficacy of target positioning by preoperative CT/MRI image fusion technique in deep brain stimulation. Methods We retrospectively analyzed the clinical data and images of 79 cases (68 with Parkinson’s disease, 11 with dystonia) who received preoperative CT/MRI image fusion in target positioning of subthalamic nucleus in deep brain stimulation. Deviation of implanted electrodes from the target nucleus of each patient were measured. Neurological evaluations of each patient before and after the treatment were performed and compared. Complications of the positioning and treatment were recorded. Results The mean deviations of the electrodes implanted on X, Y, and Z axis were 0.5 mm, 0.6 mm, and 0.6 mm, respectively. Postoperative neurologic evaluations scores of unified Parkinson’s disease rating scale (UPDRS) for Parkinson’s disease and Burke-Fahn-Marsden Dystonia Rating Scale (BFMDRS) for dystonia patients improved significantly compared to the preoperative scores (P<0.001); Complications occurred in 10.1% (8/79) patients, and main side effects were dysarthria and diplopia. Conclusion Target positioning by preoperative CT/MRI image fusion technique in deep brain stimulation has high accuracy and good clinical outcomes.

  3. Assessing infrared intensity using the evaporation rate of liquid hydrogen inside a cryogenic integrating sphere for laser fusion targets

    Science.gov (United States)

    Iwano, K.; Iwamoto, A.; Asahina, T.; Yamanoi, K.; Arikawa, Y.; Nagatomo, H.; Nakai, M.; Norimatsu, T.; Azechi, H.

    2017-07-01

    Infrared (IR) heating processes have been studied to form a deuterium layer in an inertial confinement fusion target. To understand the relationship between the IR intensity and the fuel layering time constant, we have developed a new method to assess the IR intensity during irradiation. In our method, a glass flask acting as a dummy target is filled with liquid hydrogen (LH2) and is then irradiated with 2-μm light. The IR intensity is subsequently calculated from the time constant of the LH2 evaporation rate. Although LH2 evaporation is also caused by the heat inflow from the surroundings and by the background heat, the evaporation rate due to IR heating can be accurately determined by acquiring the time constant with and without irradiation. The experimentally measured IR intensity is 0.66 mW/cm2, which agrees well with a value estimated by considering the IR photon energy balance. Our results suggest that the present method can be used to measure the IR intensity inside a cryogenic system during IR irradiation of laser fusion targets.

  4. Targeted DNA demethylation and activation of endogenous genes using programmable TALE-TET1 fusion proteins.

    Science.gov (United States)

    Maeder, Morgan L; Angstman, James F; Richardson, Marcy E; Linder, Samantha J; Cascio, Vincent M; Tsai, Shengdar Q; Ho, Quan H; Sander, Jeffry D; Reyon, Deepak; Bernstein, Bradley E; Costello, Joseph F; Wilkinson, Miles F; Joung, J Keith

    2013-12-01

    Genome-wide studies have defined cell type-specific patterns of DNA methylation that are important for regulating gene expression in both normal development and disease. However, determining the functional significance of specific methylation events remains challenging, owing to the lack of methods for removing such modifications in a targeted manner. Here we describe an approach for efficient targeted demethylation of specific CpGs in human cells using fusions of engineered transcription activator-like effector (TALE) repeat arrays and the TET1 hydroxylase catalytic domain. Using these TALE-TET1 fusions, we demonstrate that modification of critical methylated promoter CpG positions can lead to substantial increases in the expression of endogenous human genes. Our results delineate a strategy for understanding the functional significance of specific CpG methylation marks in the context of endogenous gene loci and validate programmable DNA demethylation reagents with potential utility for research and therapeutic applications.

  5. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1993--September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Hoppe, M. [ed.

    1995-04-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. During the period, GA was assigned 17 tasks in support of the Inertial Confinement Fusion program and its laboratories. This year they achieved full production capabilities for the micromachining, dimensional characterization and gold plating of hohlraums. They fabricated and delivered 726 gold-plated mandrels of 27 different types to LLNL and 48 gold-plated mandrels of two different types to LANL. They achieved full production capabilities in composite capsule production ad delivered in excess of 240 composite capsules. They continuously work to improve performance and capabilities. They were also directed to dismantle, remove, and disposition all equipment at the previous contractor (KMSF) that had radioactive contamination levels low enough that they could be exposed to the general public without radiological constraints. GA was also directed to receive and store the tritium fill equipment. They assisted LANL in the development of techniques for characterization of opaque targets. They developed deuterated and UV-opaque polymers for use by the University of Rochester`s Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process. The ICF program is anticipating experiments at NIF and the Omega Upgrade. Both facilities will require capsules containing layered D{sub 2} or D-T fuel. They continued engineering and assembly of equipment for a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments.

  6. Fusion of Imperfect Information in the Unified Framework of Random Sets Theory: Application to Target Identification

    Science.gov (United States)

    2007-11-01

    Informatique WGZ Anne-Laure Jousselme Éloi Bossé DRDC Valcartier Defence R&D Canada – Valcartier Technical Report DRDC Valcartier TR 2003-319 November 2007...Fusion of imperfect information in the unified framework of random sets theory Application to target identification Mihai Cristian Florea Informatique ...Cell CFB Esquimalt P.O. Box 17000 Stn Forces Victoria, British Columbia, V9A 7N2 Attn: Commanding Officer 1 M. C. Florea (author) Informatique WGZ inc

  7. Bearings-only fusion tracking for maneuvering target with wavelet transform in three dimensional space

    Institute of Scientific and Technical Information of China (English)

    Tian Hongwei; Jing Zhongliang; Hu Shiqiang; Li Jianxun

    2005-01-01

    A new fusion tracking algorithm is presented to track maneuvering target in three-dimensional (3D) space with bearings-only measurements. With the introduction of passive location and interacting multiple model (IMM) algorithm based on multirate model, the high-rate sequence measurements of two sensors are utilized. Simulation results show that the performance of tracking has been improved. The new algorithm removes the barrier of processing high-rate bearingsonly measurements.

  8. Z-inertial fusion energy: power plant final report FY 2006.

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Mark (University of Wisconsin, Madison, WI); Kulcinski, Gerald (University of Wisconsin, Madison, WI); Zhao, Haihua (University of California, Berkeley, CA); Cipiti, Benjamin B.; Olson, Craig Lee; Sierra, Dannelle P.; Meier, Wayne (Lawrence Livermore National Laboratories); McConnell, Paul E.; Ghiaasiaan, M. (Georgia Institute of Technology, Atlanta, GA); Kern, Brian (Georgia Institute of Technology, Atlanta, GA); Tajima, Yu (University of California, Los Angeles, CA); Campen, Chistopher (University of California, Berkeley, CA); Sketchley, Tomas (University of California, Los Angeles, CA); Moir, R (Lawrence Livermore National Laboratories); Bardet, Philippe M. (University of California, Berkeley, CA); Durbin, Samuel; Morrow, Charles W.; Vigil, Virginia L (University of Wisconsin, Madison, WI); Modesto-Beato, Marcos A.; Franklin, James Kenneth (University of California, Berkeley, CA); Smith, James Dean; Ying, Alice (University of California, Los Angeles, CA); Cook, Jason T.; Schmitz, Lothar (University of California, Los Angeles, CA); Abdel-Khalik, S. (Georgia Institute of Technology, Atlanta, GA); Farnum, Cathy Ottinger; Abdou, Mohamed A. (University of California, Los Angeles, CA); Bonazza, Riccardo (University of Wisconsin, Madison, WI); Rodriguez, Salvador B.; Sridharan, Kumar (University of Wisconsin, Madison, WI); Rochau, Gary Eugene; Gudmundson, Jesse (University of Wisconsin, Madison, WI); Peterson, Per F. (University of California, Berkeley, CA); Marriott, Ed (University of Wisconsin, Madison, WI); Oakley, Jason (University of Wisconsin, Madison, WI)

    2006-10-01

    This report summarizes the work conducted for the Z-inertial fusion energy (Z-IFE) late start Laboratory Directed Research Project. A major area of focus was on creating a roadmap to a z-pinch driven fusion power plant. The roadmap ties ZIFE into the Global Nuclear Energy Partnership (GNEP) initiative through the use of high energy fusion neutrons to burn the actinides of spent fuel waste. Transmutation presents a near term use for Z-IFE technology and will aid in paving the path to fusion energy. The work this year continued to develop the science and engineering needed to support the Z-IFE roadmap. This included plant system and driver cost estimates, recyclable transmission line studies, flibe characterization, reaction chamber design, and shock mitigation techniques.

  9. Data fusion for target tracking and classification with wireless sensor network

    Science.gov (United States)

    Pannetier, Benjamin; Doumerc, Robin; Moras, Julien; Dezert, Jean; Canevet, Loic

    2016-10-01

    In this paper, we address the problem of multiple ground target tracking and classification with information obtained from a unattended wireless sensor network. A multiple target tracking (MTT) algorithm, taking into account road and vegetation information, is proposed based on a centralized architecture. One of the key issue is how to adapt classical MTT approach to satisfy embedded processing. Based on track statistics, the classification algorithm uses estimated location, velocity and acceleration to help to classify targets. The algorithms enables tracking human and vehicles driving both on and off road. We integrate road or trail width and vegetation cover, as constraints in target motion models to improve performance of tracking under constraint with classification fusion. Our algorithm also presents different dynamic models, to palliate the maneuvers of targets. The tracking and classification algorithms are integrated into an operational platform (the fusion node). In order to handle realistic ground target tracking scenarios, we use an autonomous smart computer deposited in the surveillance area. After the calibration step of the heterogeneous sensor network, our system is able to handle real data from a wireless ground sensor network. The performance of system is evaluated in a real exercise for intelligence operation ("hunter hunt" scenario).

  10. Reaching High-Yield Fusion with a Slow Plasma Liner Compressing a Magnetized Target

    Energy Technology Data Exchange (ETDEWEB)

    Ryutov, D D; Parks, P B

    2008-03-18

    Dynamics of the compression of a magnetized plasma target by a heavy liner made of partially ionized high high-Z material is discussed. A 'soft-landing' (shockless) mode of the liner deceleration is analyzed. Conclusion is drawn that such mode is possible for the liners whose thickness at the time of the first contact with the target is smaller than, roughly, 10% of the initial (un-compressed) target radius. A combination of the plasma liner with one or two glide cones allows for a direct access to the area near the center of the reactor chamber. One can then generate plasma target inside the plasma liner at the optimum time. The other advantage of the glide cones is that they can be used to deliver additional fuel to the center of the target near the point of a maximum compression and thereby increase the fusion yield.

  11. Three dimensional passive underwater target motion analysis using correlated data fusion

    Institute of Scientific and Technical Information of China (English)

    HU Youfeng; JIAO Bingli

    2004-01-01

    In this paper a new method of passive underwater TMA (target motion analysis) using data fusion is presented. The findings of this research are based on an understanding that there is a powerful sonar system that consists of many types of sonar but with one own-ship, and that different target parameter measurements can be obtained simultaneously. For the analysis 3 data measurements, passive bearing, elevation and multipath time-delay, are used, which are divided into two groups: a group with estimates of two preliminary target parameter obtained by dealing with each group measurement independently, and a group where correlated estimates are sent to a fusion center where the correlation between two data groups are considered so that the passive underwater TMA is realized. Simulation results show that curves of parameter estimation errors obtained by using the data fusion have fast convergence and the estimation accuracy is noticeably improved. The TMA algorithm presented is verified and is of practical significance because it is easy to be realized in one ship.

  12. Sphingolipid and cholesterol dependence of alphavirus membrane fusion - Lack of correlation with lipid raft formation in target liposomes

    NARCIS (Netherlands)

    Waarts, BL; Bittman, R; Wilschut, J

    2002-01-01

    Semliki Forest virus (SFV) and Sindbis virus (SIN) are enveloped viruses that infect their host cells by receptor-mediated endocytosis and subsequent fusion from within acidic endosomes. Fusion of the viral envelope requires the presence of both cholesterol and sphingolipids in the target membrane.

  13. Membrane fusion induced by a short fusogenic peptide is assessed by its insertion and orientation into target bilayers

    NARCIS (Netherlands)

    Martin, [No Value; Pecheur, EI; Ruysschaert, JM; Hoekstra, D

    1999-01-01

    To clarify the molecular mechanism by which an amphipathic negatively charged peptide consisting of 11 residues (WAE) induces fusion, and the relevance of these features for fusion, its mode of insertion and orientation into target bilayers were investigated. Using attenuated total reflection

  14. Challenges of high power diode-pumped lasers for fusion energy

    Institute of Scientific and Technical Information of China (English)

    Bruno; Le; Garrec

    2014-01-01

    This paper reviews the different challenges that are encountered in the delivery of high power lasers as drivers for fusion energy.We will focus on diode-pumped solid-state lasers and we will highlight some of the main recent achievements when using ytterbium,cryogenic cooling and ceramic gain media.Apart from some existing fusion facilities and some military applications of diode-pumped solid-state lasers,we will show that diode-pumped solid-state lasers are scalable to inertial fusion energy(IFE)’s facility level and that the all-fiber laser scheme is very promising.

  15. Process for manufacture of inertial confinement fusion targets and resulting product

    Science.gov (United States)

    Masnari, Nino A.; Rensel, Walter B.; Robinson, Merrill G.; Solomon, David E.; Wise, Kensall D.; Wuttke, Gilbert H.

    1982-01-01

    An ICF target comprising a spherical pellet of fusion fuel surrounded by a concentric shell; and a process for manufacturing the same which includes the steps of forming hemispheric shells of a silicon or other substrate material, adhering the shell segments to each other with a fuel pellet contained concentrically therein, then separating the individual targets from the parent substrate. Formation of hemispheric cavities by deposition or coating of a mold substrate is also described. Coatings or membranes may also be applied to the interior of the hemispheric segments prior to joining.

  16. Targeting leukemic fusion proteins with small interfering RNAs: recent advances and therapeutic potentials

    Institute of Scientific and Technical Information of China (English)

    Maria THOMAS; Johann GREIL; Olaf HEIDENREICH

    2006-01-01

    RNA interference has become an indispensable research tool to study gene functions in a wide variety of organisms.Because of their high efficacy and specificity,RNA interference-based approaches may also translate into new therapeutic strategies to treat human diseases.In particular,oncogenes such as leukemic fusion proteins,which arise from chromosomal translocations,are promising targets for such gene silencing approaches,because they are exclusively expressed in precancerous and cancerous tissues,and because they are frequently indispensable for maintaining the malignant phenotype.This review summarizes recent developments in targeting leukemia-specific genes and discusses problems and approaches for possible clinical applications.

  17. Integrated process modeling for the laser inertial fusion Energy (LIFE) generation system

    Energy Technology Data Exchange (ETDEWEB)

    Meier, W R; Anklam, T M; Erlandson, A C; Miles, R R; Simon, A J; Sawicki, R; Storm, E

    2009-10-22

    A concept for a new fusion-fission hybrid technology is being developed at Lawrence Livermore National Laboratory. The primary application of this technology is base-load electrical power generation. However, variants of the baseline technology can be used to 'burn' spent nuclear fuel from light water reactors or to perform selective transmutation of problematic fission products. The use of a fusion driver allows very high burn-up of the fission fuel, limited only by the radiation resistance of the fuel form and system structures. As a part of this process, integrated process models have been developed to aid in concept definition. Several models have been developed. A cost scaling model allows quick assessment of design changes or technology improvements on cost of electricity. System design models are being used to better understand system interactions and to do design trade-off and optimization studies. Here we describe the different systems models and present systems analysis results. Different market entry strategies are discussed along with potential benefits to US energy security and nuclear waste disposal. Advanced technology options are evaluated and potential benefits from additional R&D targeted at the different options is quantified.

  18. Integrated process modeling for the laser inertial fusion energy (LIFE) generation system

    Science.gov (United States)

    Meier, W. R.; Anklam, T. M.; Erlandson, A. C.; Miles, R. R.; Simon, A. J.; Sawicki, R.; Storm, E.

    2010-08-01

    A concept for a new fusion-fission hybrid technology is being developed at Lawrence Livermore National Laboratory. The primary application of this technology is base-load electrical power generation. However, variants of the baseline technology can be used to "burn" spent nuclear fuel from light water reactors or to perform selective transmutation of problematic fission products. The use of a fusion driver allows very high burn-up of the fission fuel, limited only by the radiation resistance of the fuel form and system structures. As a part of this process, integrated process models have been developed to aid in concept definition. Several models have been developed. A cost scaling model allows quick assessment of design changes or technology improvements on cost of electricity. System design models are being used to better understand system interactions and to do design trade-off and optimization studies. Here we describe the different systems models and present systems analysis results. Different market entry strategies are discussed along with potential benefits to US energy security and nuclear waste disposal. Advanced technology options are evaluated and potential benefits from additional R&D targeted at the different options is quantified.

  19. Progress in safety and environmental aspects of inertial fusion energy at Lawrence Livermore National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J F; Reyes, S; Meier, W R

    2000-06-01

    Lawrence Livermore National Laboratory (LLNL) is making significant progress in several areas related to the safety and environmental (S and E) aspects of inertial fusion energy (IFE). A detailed accident analysis has been completed for the HYLIFE-II power plant design. Additional accident analyses are underway for both the HYLIFE-II and Sombrero designs. Other S and E work at LLNL has addressed the issue of the driver-chamber interface and its importance for both heavy-ion and laser-driven IFE. Radiation doses and fluences have been calculated for final focusing mirrors and magnets and shielding optimization is underway to extend the anticipated lifetimes for key components. Target designers/fabrication specialists have been provided with ranking information related to the S and E characteristics of candidate target materials (e.g., ability to recycle, accident consequences, and waste management). Ongoing work in this area will help guide research directions and the selection of target materials. Published and continuing work on fast ignition has demonstrated some of the potentially attractive S and E features of such designs. In addition to reducing total driver energies, fast ignition may ease target fabrication requirements, reduce radiation damage rates, and enable the practical use of advanced (e.g., tritium-lean) labels with significantly reduced neutron production rates, the possibility of self-breeding targets, and dramatically increased flexibility in blanket design. Domestic and international collaborations are key to success in the above areas. A brief summary of each area is given and plans for future work are outlined.

  20. Inertial Confinement Fusion Target Component Fabrication and Technology Development report. Annual report, October 1, 1992--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Steinman, D. [ed.

    1994-03-01

    On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities which took place under this contract during the period of October 1, 1992 through September 30, 1993. During this period, GA was assigned 18 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included ``Capabilities Activation`` and ``Capabilities Demonstration`` to enable us to begin production of glass and composite polymer capsules. Capsule delivery tasks included ``Small Glass Shell Deliveries`` and ``Composite Polymer Capsules`` for Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL). We also were asked to provide direct ``Onsite Support`` at LLNL and LANL. We continued planning for the transfer of ``Micromachining Equipment from Rocky Flats`` and established ``Target Component Micromachining and Electroplating Facilities`` at GA. We fabricated over 1100 films and filters of 11 types for Sandia National Laboratory and provided full-time onsite engineering support for target fabrication and characterization. We initiated development of methods to make targets for the Naval Research Laboratory. We investigated spherical interferometry, built an automated capsule sorter, and developed an apparatus for calorimetric measurement of fuel fill for LLNL. We assisted LANL in the ``Characterization of Opaque b-Layered Targets.`` We developed deuterated and UV-opaque polymers for use by the University of Rochester`s Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process.

  1. The Epstein-Barr virus (EBV) glycoprotein B cytoplasmic C-terminal tail domain regulates the energy requirement for EBV-induced membrane fusion.

    Science.gov (United States)

    Chen, Jia; Zhang, Xianming; Jardetzky, Theodore S; Longnecker, Richard

    2014-10-01

    The entry of enveloped viruses into host cells is preceded by membrane fusion, which in Epstein-Barr virus (EBV) is thought to be mediated by the refolding of glycoprotein B (gB) from a prefusion to a postfusion state. In our current studies, we characterized a gB C-terminal tail domain (CTD) mutant truncated at amino acid 843 (gB843). This truncation mutant is hyperfusogenic as monitored by syncytium formation and in a quantitative fusion assay and is dependent on gH/gL for fusion activity. gB843 can rescue the fusion function of other glycoprotein mutants that have null or decreased fusion activity in epithelial and B cells. In addition, gB843 requires less gp42 and gH/gL for fusion, and can function in fusion at a lower temperature than wild-type gB, indicating a lower energy requirement for fusion activation. Since a key step in fusion is the conversion of gB from a prefusion to an active postfusion state by gH/gL, gB843 may access this activated gB state more readily. Our studies indicate that the gB CTD may participate in the fusion function by maintaining gB in an inactive prefusion form prior to activation by receptor binding. Importance: Diseases resulting from Epstein-Barr virus (EBV) infection in humans range from the fairly benign disease infectious mononucleosis to life-threatening cancer. As an enveloped virus, EBV must fuse with a host cell membrane for entry and infection by using glycoproteins gH/gL, gB, and gp42. Among these glycoproteins, gB is thought to be the protein that executes fusion. To further characterize the function of the EBV gB cytoplasmic C-terminal tail domain (CTD) in fusion, we used a previously constructed CTD truncation mutant and studied its fusion activity in the context of other EBV glycoprotein mutants. From these studies, we find that the gB CTD regulates fusion by altering the energy requirements for the triggering of fusion mediated by gH/gL or gp42. Overall, our studies may lead to a better understanding of EBV fusion

  2. Targeted codon optimization improves translational fidelity for an Fc fusion protein.

    Science.gov (United States)

    Hutterer, Katariina M; Zhang, Zhongqi; Michaels, Mark Leo; Belouski, Ed; Hong, Robert W; Shah, Bhavana; Berge, Mark; Barkhordarian, Hedieh; Le, Eleanor; Smith, Steve; Winters, Dwight; Abroson, Frank; Hecht, Randy; Liu, Jennifer

    2012-11-01

    High levels of translational errors, both truncation and misincorporation in an Fc-fusion protein were observed. Here, we demonstrate the impact of several commercially available codon optimization services, and compare to a targeted strategy. Using the targeted strategy, only codons known to have translational errors are modified. For an Fc-fusion protein expressed in Escherichia coli, the targeted strategy, in combination with appropriate fermentation conditions, virtually eliminated misincorporation (proteins produced with a wrong amino acid sequence), and reduced the level of truncation. The use of full optimization using commercially available strategies reduced the initial errors, but introduced different misincorporations. However, truncation was higher using the targeted strategy than for most of the full optimization strategies. This targeted approach, along with monitoring of translation fidelity and careful attention to fermentation conditions is key to minimizing translational error and ensuring high-quality expression. These findings should be useful for other biopharmaceutical products, as well as any other transgenic constructs where protein quality is important.

  3. Evaluation of MRI-TRUS fusion versus cognitive registration accuracy for MRI-targeted, TRUS-guided prostate biopsy.

    Science.gov (United States)

    Cool, Derek W; Zhang, Xuli; Romagnoli, Cesare; Izawa, Jonathan I; Romano, Walter M; Fenster, Aaron

    2015-01-01

    The purpose of this article is to compare transrectal ultrasound (TRUS) biopsy accuracies of operators with different levels of prostate MRI experience using cognitive registration versus MRI-TRUS fusion to assess the preferred method of TRUS prostate biopsy for MRI-identified lesions. SUBJECTS AND METHODS; One hundred patients from a prospective prostate MRI-TRUS fusion biopsy study were reviewed to identify all patients with clinically significant prostate adenocarcinoma (PCA) detected on MRI-targeted biopsy. Twenty-five PCA tumors were incorporated into a validated TRUS prostate biopsy simulator. Three prostate biopsy experts, each with different levels of experience in prostate MRI and MRI-TRUS fusion biopsy, performed a total of 225 simulated targeted biopsies on the MRI lesions as well as regional biopsy targets. Simulated biopsies performed using cognitive registration with 2D TRUS and 3D TRUS were compared with biopsies performed under MRI-TRUS fusion. Two-dimensional and 3D TRUS sampled only 48% and 45% of clinically significant PCA MRI lesions, respectively, compared with 100% with MRI-TRUS fusion. Lesion sampling accuracy did not statistically significantly vary according to operator experience or tumor volume. MRI-TRUS fusion-naïve operators showed consistent errors in targeting of the apex, midgland, and anterior targets, suggesting that there is biased error in cognitive registration. The MRI-TRUS fusion expert correctly targeted the prostate apex; however, his midgland and anterior mistargeting was similar to that of the less-experienced operators. MRI-targeted TRUS-guided prostate biopsy using cognitive registration appears to be inferior to MRI-TRUS fusion, with fewer than 50% of clinically significant PCA lesions successfully sampled. No statistically significant difference in biopsy accuracy was seen according to operator experience with prostate MRI or MRI-TRUS fusion.

  4. The Long way Towards Inertial Fusion Energy (lirpp Vol. 13)

    Science.gov (United States)

    Velarde, Guillermo

    2016-10-01

    In 1955 the first Geneva Conference was held in which two important events took place. Firstly, the announcement by President Eisenhower of the Program Atoms for Peace declassifying the information concerning nuclear fission reactors. Secondly, it was forecast that due to the research made on stellerators and magnetic mirrors, the first demo fusion facility would be in operation within ten years. This forecasting, as all of us know today, was a mistake. Forty years afterwards, we can say that probably the first Demo Reactor will be operative in some years more and I sincerely hope that it will be based on the inertial fusion concept...

  5. Will fusion be ready to meet the energy challenge for the 21st century?

    Science.gov (United States)

    Bréchet, Yves; Massard, Thierry

    2016-05-01

    Finite amount of fossil fuel, global warming, increasing demand of energies in emerging countries tend to promote new sources of energies to meet the needs of the coming centuries. Despite their attractiveness, renewable energies will not be sufficient both because of intermittency but also because of the pressure they would put on conventional materials. Thus nuclear energy with both fission and fusion reactors remain the main potential source of clean energy for the coming centuries. France has made a strong commitment to fusion reactor through ITER program. But following and sharing Euratom vision on fusion, France supports the academic program on Inertial Fusion Confinement with direct drive and especially the shock ignition scheme which is heavily studied among the French academic community. LMJ a defense facility for nuclear deterrence is also open to academic community along with a unique PW class laser PETAL. Research on fusion at LMJ-PETAL is one of the designated topics for experiments on the facility. Pairing with other smaller European facilities such as Orion, PALS or LULI2000, LMJ-PETAL will bring new and exciting results and contribution in fusion science in the coming years.

  6. Improved prediction of drug-target interactions using regularized least squares integrating with kernel fusion technique

    Energy Technology Data Exchange (ETDEWEB)

    Hao, Ming; Wang, Yanli, E-mail: ywang@ncbi.nlm.nih.gov; Bryant, Stephen H., E-mail: bryant@ncbi.nlm.nih.gov

    2016-02-25

    Identification of drug-target interactions (DTI) is a central task in drug discovery processes. In this work, a simple but effective regularized least squares integrating with nonlinear kernel fusion (RLS-KF) algorithm is proposed to perform DTI predictions. Using benchmark DTI datasets, our proposed algorithm achieves the state-of-the-art results with area under precision–recall curve (AUPR) of 0.915, 0.925, 0.853 and 0.909 for enzymes, ion channels (IC), G protein-coupled receptors (GPCR) and nuclear receptors (NR) based on 10 fold cross-validation. The performance can further be improved by using a recalculated kernel matrix, especially for the small set of nuclear receptors with AUPR of 0.945. Importantly, most of the top ranked interaction predictions can be validated by experimental data reported in the literature, bioassay results in the PubChem BioAssay database, as well as other previous studies. Our analysis suggests that the proposed RLS-KF is helpful for studying DTI, drug repositioning as well as polypharmacology, and may help to accelerate drug discovery by identifying novel drug targets. - Graphical abstract: Flowchart of the proposed RLS-KF algorithm for drug-target interaction predictions. - Highlights: • A nonlinear kernel fusion algorithm is proposed to perform drug-target interaction predictions. • Performance can further be improved by using the recalculated kernel. • Top predictions can be validated by experimental data.

  7. The National Ignition Facility: Status and Plans for Laser Fusion and High-Energy-Density Experimental Studies

    Energy Technology Data Exchange (ETDEWEB)

    Moses, E I; Wuest, C R

    2002-10-16

    The National Ignition Facility (NIF), currently under construction at the University of California's Lawrence Livermore National Laboratory, is a stadium-sized facility containing a 192-beam, 1.8-Megajoule, 500-Terawatt, 351-nm laser system and a 10-meter diameter target chamber with room for nearly 100 experimental diagnostics. NIF is being built by the National Nuclear Security Administration and when completed will be the world's largest laser experimental system, providing a national center to study inertial confinement fusion and the physics of matter at extreme energy densities and pressures. NIF will provide 192 energetic laser beams that will compress small fusion targets to conditions where they will ignite and burn, liberating more energy than is required to initiate the fusion reactions. NIF experiments will allow the study of physical processes at temperatures approaching 100 million K and 100 billion times atmospheric pressure. These conditions exist naturally only in the interior of stars and in nuclear weapons explosions. In the course of designing the world's most energetic laser system, a number of significant technology breakthroughs have been achieved. Research is also underway to develop a shorter pulse capability on NIF for very high power and extreme electromagnetic field research and applications. We discuss here the technology challenges and solutions that have made NIF possible, along with enhancements to NIF's design that could lead to near-exawatt power levels.

  8. Office of Fusion Energy Sciences. A ten-year perspective (2015-2025)

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-12-01

    The vision described here builds on the present U.S. activities in fusion plasma and materials science relevant to the energy goal and extends plasma science at the frontier of discovery. The plan is founded on recommendations made by the National Academies, a number of recent studies by the Fusion Energy Sciences Advisory Committee (FESAC), and the Administration’s views on the greatest opportunities for U.S. scientific leadership.This report highlights five areas of critical importance for the U.S. fusion energy sciences enterprise over the next decade: 1) Massively parallel computing with the goal of validated whole-fusion-device modeling will enable a transformation in predictive power, which is required to minimize risk in future fusion energy development steps; 2) Materials science as it relates to plasma and fusion sciences will provide the scientific foundations for greatly improved plasma confinement and heat exhaust; 3) Research in the prediction and control of transient events that can be deleterious to toroidal fusion plasma confinement will provide greater confidence in machine designs and operation with stable plasmas; 4) Continued stewardship of discovery in plasma science that is not expressly driven by the energy goal will address frontier science issues underpinning great mysteries of the visible universe and help attract and retain a new generation of plasma/fusion science leaders; 5) FES user facilities will be kept world-leading through robust operations support and regular upgrades. Finally, we will continue leveraging resources among agencies and institutions and strengthening our partnerships with international research facilities.

  9. Interrelationships between mitochondrial fusion, energy metabolism and oxidative stress during development in Caenorhabditis elegans

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, Kayo [Department of Molecular Life Science, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan); Education and Research Support Center, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan); Hartman, Philip S. [Biology Department, Texas Christian University, Fort Worth, TX 76129 (United States); Ishii, Takamasa [Department of Molecular Life Science, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan); Suda, Hitoshi [School of High-Technology for Human Welfare, Tokai University, Nishino 317, Numazu, Shizuoka 410-0395 (Japan); Akatsuka, Akira [Education and Research Support Center, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan); Shoyama, Tetsuji [School of High-Technology for Human Welfare, Tokai University, Nishino 317, Numazu, Shizuoka 410-0395 (Japan); Miyazawa, Masaki [Department of Molecular Life Science, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan); Ishii, Naoaki, E-mail: nishii@is.icc.u-tokai.ac.jp [Department of Molecular Life Science, Tokai University School of Medicine, Isehara, Kanagawa 259-1193 (Japan)

    2011-01-21

    Research highlights: {yields} Growth and development of a fzo-1 mutant defective in the fusion process of mitochondria was delayed relative to the wild type of Caenorhabditis elegans. {yields} Oxygen sensitivity during larval development, superoxide production and carbonyl protein accumulation of the fzo-1 mutant were similar to wild type. {yields} fzo-1 animals had significantly lower metabolism than did N2 and mev-1 overproducing superoxide from mitochondrial electron transport complex II. {yields} Mitochondrial fusion can profoundly affect energy metabolism and development. -- Abstract: Mitochondria are known to be dynamic structures with the energetically and enzymatically mediated processes of fusion and fission responsible for maintaining a constant flux. Mitochondria also play a role of reactive oxygen species production as a byproduct of energy metabolism. In the current study, interrelationships between mitochondrial fusion, energy metabolism and oxidative stress on development were explored using a fzo-1 mutant defective in the fusion process and a mev-1 mutant overproducing superoxide from mitochondrial electron transport complex II of Caenorhabditis elegans. While growth and development of both single mutants was slightly delayed relative to the wild type, the fzo-1;mev-1 double mutant experienced considerable delay. Oxygen sensitivity during larval development, superoxide production and carbonyl protein accumulation of the fzo-1 mutant were similar to wild type. fzo-1 animals had significantly lower metabolism than did N2 and mev-1. These data indicate that mitochondrial fusion can profoundly affect energy metabolism and development.

  10. The big experimental manual of Free Energy. Cold Fusion - Tesla-Waves - Space-Quantum-Energy - a.o.; Das grosse Freie Energie Experimentier-Handbuch. Kalte Fusion - Tesla-Wellen - Raum-Quanten-Energie - u.v.m.

    Energy Technology Data Exchange (ETDEWEB)

    Lay, P.; Chmela, H.; Wiedergut, W.

    2004-07-01

    The main topics of the lectures are: Experiments on cold fusion; Information on space-quantum energy; phenomena of rotating magnets; advanced electrostatic motors; generation of scalar waves; complex rotating fields and levitation from an advanced view; free energy converters. (GL)

  11. Interaction of a self-focused laser beam with a DT fusion target in a plasma-loaded cone-guided ICF scheme

    Science.gov (United States)

    Saedjalil, N.; Mehrangiz, M.; Jafari, S.; Ghasemizad, A.

    2016-06-01

    In this paper, the interaction of a self-focused laser beam with a DT fusion target in a plasma-loaded cone-guided ICF scheme has been presented. We propose here to merge a plasma-loaded cone with the precompressed DT target in order to strongly focus the incident laser beam on the core to improve the fusion gain. The WKB approximation is used to derive a differential equation that governs the evolution of beamwidth of the incident laser beam with the distance of propagation in the plasma medium. The effects of initial plasma and laser parameters, such as initial plasma electron temperature, initial radius of the laser beam, initial laser beam intensity and plasma density, on self-focusing and defocusing of the Gaussian laser beam have been studied. Numerical results indicate that with increasing the plasma frequency (or plasma density) in the cone, the laser beam will be self-focused noticeably, while for a thinner laser beam (with small radius), it will diverge as propagate in the cone. By evaluating the energy deposition of the relativistic electron ignitors in the fuel, the importance of electron transportation in the cone-attached shell was demonstrated. Moreover, by lessening the least energy needed for ignition, the electrons coupling with the pellet enhances. Therefore, it increases the fusion efficiency. In this scheme, with employing a plasma-loaded cone, the fusion process improves without needing an ultrahigh-intensity laser beam in a conventional ICF.

  12. Fusion and Direct Reactions of Halo Nuclei at Energies around the Coulomb Barrier

    CERN Document Server

    Keeley, N; Raabe, R; Sida, J L

    2007-01-01

    The present understanding of reaction processes involving light unstable nuclei at energies around the Coulomb barrier is reviewed. The effect of coupling to direct reaction channels on elastic scattering and fusion is investigated, with the focus on halo nuclei. A list of definitions of processes is given, followed by a review of the experimental and theoretical tools and information presently available. The effect of couplings on elastic scattering and fusion is studied with a series of model calculations within the coupled-channels framework. The experimental data on fusion are compared to "bare" no-coupling one-dimensional barrier penetration model calculations. On the basis of these calculations and comparisons with experimental data, conclusions are drawn from the observation of recurring features. The total fusion cross sections for halo nuclei show a suppression with respect to the "bare" calculations at energies just above the barrier that is probably due to single neutron transfer reactions. The dat...

  13. Study of the 12C+12C fusion reactions near the Gamow energy

    CERN Document Server

    Spillane, T; Bordeanu, C; Gialanella, L; Raiola, F; Rolfs, C; Romano, M; Sch"urmann, D; Schweitzer, J; Strieder, F; Zeng, S

    2007-01-01

    The fusion reactions 12C(12C,a)20Ne and 12C(12C,p)23Na have been studied from E = 2.10 to 4.75 MeV by gamma-ray spectroscopy using a C target with ultra-low hydrogen contamination. The deduced astrophysical S(E)* factor exhibits new resonances at E <= 3.0 MeV, in particular a strong resonance at E = 2.14 MeV, which lies at the high-energy tail of the Gamow peak. The resonance increases the present non-resonant reaction rate of the alpha channel by a factor of 5 near T = 8x10^8 K. Due to the resonance structure, extrapolation to the Gamow energy E_G = 1.5 MeV is quite uncertain. An experimental approach based on an underground accelerator placed in a salt mine in combination with a high efficiency detection setup could provide data over the full E_G energy range.

  14. Role of the Hoyle state in the 12C+12C fusion at low energies

    Directory of Open Access Journals (Sweden)

    Descouvemont P.

    2014-04-01

    Full Text Available The 12C+12C fusion reaction is investigated in a multichannel folding model, using the density-dependent DDM3Y nucleon-nucleon interaction. The 12C(01+, 2+, 02+, 3− states are included, and their densities are taken from a microscopic cluster calculation. Absorption to fusion channels is simulated by a short-range imaginary potential and the model does not contain any fitting parameter. We compute elastic and fusion cross sections simultaneously. The role of 12C+12C inelastic channels and, in particular, of the 12C(01++12C(02+ channel involving the Hoyle state is important even at low energies.

  15. Isotopic dependence of fusion enhancement of various heavy ion systems using energy dependent Woods-Saxon potential

    Science.gov (United States)

    Gautam, Manjeet Singh

    2015-01-01

    In the present work, the fusion of symmetric and asymmetric projectile-target combinations are deeply analyzed within the framework of energy dependent Woods-Saxon potential model (EDWSP model) in conjunction with one dimensional Wong formula and the coupled channel code CCFULL. The neutron transfer channels and the inelastic surface excitations of collision partners are dominating mode of couplings and the coupling of relative motion of colliding nuclei to such relevant internal degrees of freedom produces a significant fusion enhancement at sub-barrier energies. It is quite interesting that the effects of dominant intrinsic degrees of freedom such as multi-phonon vibrational states, neutron transfer channels and proton transfer channels can be simulated by introducing the energy dependence in the nucleus-nucleus potential (EDWSP model). In the EDWSP model calculations, a wide range of diffuseness parameter ranging from a = 0.85 fm to a = 0.97 fm, which is much larger than a value (a = 0.65 fm) extracted from the elastic scattering data, is needed to reproduce sub-barrier fusion data. However, such diffuseness anomaly, which might be an artifact of some dynamical effects, has been resolved by trajectory fluctuation dissipation (TFD) model wherein the resulting nucleus-nucleus potential possesses normal diffuseness parameter.

  16. Isotopic dependence of fusion enhancement of various heavy ion systems using energy dependent Woods–Saxon potential

    Energy Technology Data Exchange (ETDEWEB)

    Gautam, Manjeet Singh, E-mail: gautammanjeet@gmail.com

    2015-01-15

    In the present work, the fusion of symmetric and asymmetric projectile–target combinations are deeply analyzed within the framework of energy dependent Woods–Saxon potential model (EDWSP model) in conjunction with one dimensional Wong formula and the coupled channel code CCFULL. The neutron transfer channels and the inelastic surface excitations of collision partners are dominating mode of couplings and the coupling of relative motion of colliding nuclei to such relevant internal degrees of freedom produces a significant fusion enhancement at sub-barrier energies. It is quite interesting that the effects of dominant intrinsic degrees of freedom such as multi-phonon vibrational states, neutron transfer channels and proton transfer channels can be simulated by introducing the energy dependence in the nucleus–nucleus potential (EDWSP model). In the EDWSP model calculations, a wide range of diffuseness parameter ranging from a=0.85 fm to a=0.97 fm, which is much larger than a value (a=0.65 fm) extracted from the elastic scattering data, is needed to reproduce sub-barrier fusion data. However, such diffuseness anomaly, which might be an artifact of some dynamical effects, has been resolved by trajectory fluctuation dissipation (TFD) model wherein the resulting nucleus–nucleus potential possesses normal diffuseness parameter.

  17. Energy and the future: Sustainable methods of energy use from passive architecture to fusion. Lectures; Energie und Zukunft: Zukunftsweisende Methoden der Energienutzung vom Passivhaus bis zur Fusion. Vortraege

    Energy Technology Data Exchange (ETDEWEB)

    Nahm, W.; Schultze, K. [eds.

    1998-12-31

    In the run-up to the Kyoto conference, there is far-reaching agreement that the world energy industry needs to be reconstructed by the middle of the next century if a climate catastrophe is to be avoided. But how this goal can be reached is controversial. The risks involved are described in contributions concerned with German energy policy, the insurance sector, and scenarios for mitigating carbon dioxides on the basis of the Ikarus model. But the focus of this annual report of DPG`s task force Energy is on reports on longer-term technologies and methods. Two papers describe the state of the art of fusion research. In the conventional energy sector, high-efficiency absorption-type refrigerators and thermal engines, and fuel conservation through low-cost passive architecture are dealt with inter alia. Other lectures report on the state of solar energy utilization and process chains in the hydrogen-based economy. Five papers are individually listed in the Energy database. (orig.) [Deutsch] Im Vorfeld der Konferenz von Kyoto besteht weitgehende Einigkeit, dass die Weltenergiewirtschaft bis zur Mitte des naechsten Jahrhunderts umgestaltet werden muss, um eine Klimakatastrophe zu verhindern. Der Weg dahin ist umstritten. Seine Risiken kommen in Beitraegen zur deutschen Energiepolitik, zur Versicherungswirtschaft und zu Szenarien der Minderung der CO{sub 2}-Emissionen auf der Basis des Ikarus-Modells zum Ausdruck. Im Mittelpunkt des Jahresbandes des Arbeitskreises Energie der DPG stehen diesmal jedoch Berichte ueber laengerfristig angelegte Technologien und Methoden. Zwei Beitraege berichten ueber den Stand der Fusionsforschung. Im konventionellen Bereich geht es u.a. um hocheffiziente Absorptionsmaschinen zur Versorgung mit Kaelte und Waerme und um die Brennstoffeinsparung durch kostenguenstige Passivhaeuser. Andere Vortraege berichten ueber den Stand der Nutzung der Sonnenenergie und Prozessketten in der Wasserstoffwirtschaft. Fuer die Datenbank Energy wurden fuenf

  18. TALE-PvuII fusion proteins--novel tools for gene targeting.

    Directory of Open Access Journals (Sweden)

    Mert Yanik

    Full Text Available Zinc finger nucleases (ZFNs consist of zinc fingers as DNA-binding module and the non-specific DNA-cleavage domain of the restriction endonuclease FokI as DNA-cleavage module. This architecture is also used by TALE nucleases (TALENs, in which the DNA-binding modules of the ZFNs have been replaced by DNA-binding domains based on transcription activator like effector (TALE proteins. Both TALENs and ZFNs are programmable nucleases which rely on the dimerization of FokI to induce double-strand DNA cleavage at the target site after recognition of the target DNA by the respective DNA-binding module. TALENs seem to have an advantage over ZFNs, as the assembly of TALE proteins is easier than that of ZFNs. Here, we present evidence that variant TALENs can be produced by replacing the catalytic domain of FokI with the restriction endonuclease PvuII. These fusion proteins recognize only the composite recognition site consisting of the target site of the TALE protein and the PvuII recognition sequence (addressed site, but not isolated TALE or PvuII recognition sites (unaddressed sites, even at high excess of protein over DNA and long incubation times. In vitro, their preference for an addressed over an unaddressed site is > 34,000-fold. Moreover, TALE-PvuII fusion proteins are active in cellula with minimal cytotoxicity.

  19. TALE-PvuII fusion proteins--novel tools for gene targeting.

    Science.gov (United States)

    Yanik, Mert; Alzubi, Jamal; Lahaye, Thomas; Cathomen, Toni; Pingoud, Alfred; Wende, Wolfgang

    2013-01-01

    Zinc finger nucleases (ZFNs) consist of zinc fingers as DNA-binding module and the non-specific DNA-cleavage domain of the restriction endonuclease FokI as DNA-cleavage module. This architecture is also used by TALE nucleases (TALENs), in which the DNA-binding modules of the ZFNs have been replaced by DNA-binding domains based on transcription activator like effector (TALE) proteins. Both TALENs and ZFNs are programmable nucleases which rely on the dimerization of FokI to induce double-strand DNA cleavage at the target site after recognition of the target DNA by the respective DNA-binding module. TALENs seem to have an advantage over ZFNs, as the assembly of TALE proteins is easier than that of ZFNs. Here, we present evidence that variant TALENs can be produced by replacing the catalytic domain of FokI with the restriction endonuclease PvuII. These fusion proteins recognize only the composite recognition site consisting of the target site of the TALE protein and the PvuII recognition sequence (addressed site), but not isolated TALE or PvuII recognition sites (unaddressed sites), even at high excess of protein over DNA and long incubation times. In vitro, their preference for an addressed over an unaddressed site is > 34,000-fold. Moreover, TALE-PvuII fusion proteins are active in cellula with minimal cytotoxicity.

  20. Materials studies for magnetic fusion energy applications at low temperatures, volume 12

    Science.gov (United States)

    Reed, R. P.; Tobler, R. L.

    1989-11-01

    The results are given of a research program to determine the properties of materials that may be used in cryogenic structures for the superconducting magnets of fusion energy power plants and prototypes. The program was developed jointly by the staffs of the National Institute of Standards and Technology and the Office of Fusion Energy of the Department of Energy. Research results for 1988 are presented in technical papers under four headings that reflect the main program areas: Structural Alloys; Welding; Technology Transfer; and United States-Japan Development of Test Standards. Objectives and research highlights are summarized in the introduction to each program area.

  1. Computational modeling of joint U.S.-Russian experiments relevant to magnetic compression/magnetized target fusion (MAGO/MTF)

    Energy Technology Data Exchange (ETDEWEB)

    Sheehey, P.T.; Faehl, R.J.; Kirkpatrick, R.C.; Lindemuth, I.R. [Los Alamos National Lab., NM (United States)

    1997-12-31

    Magnetized Target Fusion (MTF) experiments, in which a preheated and magnetized target plasma is hydrodynamically compressed to fusion conditions, present some challenging computational modeling problems. Recently, joint experiments relevant to MTF (Russian acronym MAGO, for Magnitnoye Obzhatiye, or magnetic compression) have been performed by Los Alamos National Laboratory and the All-Russian Scientific Research Institute of Experimental Physics (VNIIEF). Modeling of target plasmas must accurately predict plasma densities, temperatures, fields, and lifetime; dense plasma interactions with wall materials must be characterized. Modeling of magnetically driven imploding solid liners, for compression of target plasmas, must address issues such as Rayleigh-Taylor instability growth in the presence of material strength, and glide plane-liner interactions. Proposed experiments involving liner-on-plasma compressions to fusion conditions will require integrated target plasma and liner calculations. Detailed comparison of the modeling results with experiment will be presented.

  2. Dense Plasma Focus - From Alternative Fusion Source to Versatile High Energy Density Plasma Source for Plasma Nanotechnology

    Science.gov (United States)

    Rawat, R. S.

    2015-03-01

    The dense plasma focus (DPF), a coaxial plasma gun, utilizes pulsed high current electrical discharge to heat and compress the plasma to very high density and temperature with energy densities in the range of 1-10 × 1010 J/m3. The DPF device has always been in the company of several alternative magnetic fusion devices as it produces intense fusion neutrons. Several experiments conducted on many different DPF devices ranging over several order of storage energy have demonstrated that at higher storage energy the neutron production does not follow I4 scaling laws and deteriorate significantly raising concern about the device's capability and relevance for fusion energy. On the other hand, the high energy density pinch plasma in DPF device makes it a multiple radiation source of ions, electron, soft and hard x-rays, and neutrons, making it useful for several applications in many different fields such as lithography, radiography, imaging, activation analysis, radioisotopes production etc. Being a source of hot dense plasma, strong shockwave, intense energetic beams and radiation, etc, the DPF device, additionally, shows tremendous potential for applications in plasma nanoscience and plasma nanotechnology. In the present paper, the key features of plasma focus device are critically discussed to understand the novelties and opportunities that this device offers in processing and synthesis of nanophase materials using, both, the top-down and bottom-up approach. The results of recent key experimental investigations performed on (i) the processing and modification of bulk target substrates for phase change, surface reconstruction and nanostructurization, (ii) the nanostructurization of PLD grown magnetic thin films, and (iii) direct synthesis of nanostructured (nanowire, nanosheets and nanoflowers) materials using anode target material ablation, ablated plasma and background reactive gas based synthesis and purely gas phase synthesis of various different types of

  3. Mobilization of the private sector in effective development of fusion energy: Papers for and a summary of a workshop

    Science.gov (United States)

    Four papers and a summary of a workshop on the mobilization of the private sector in developing fusion energy is reported. The workshop is one of a series which assesses Federal policy options relating to the commercialization of selected energy technologies viewed as alternatives to petroleum-derived fuels. The papers focused on the potential roles to be played by fusion energy in the future electric generating industry; current commitments and participation of the private sector in fusion energy development; suggestions for policy incentives to enhance private participation in fusion research; organization, staffing, and operating a center for fusion engineering; the industrial structure and practices in developing and deploying power generating facilities and their implications in relation to fusion energy development; and characteristics required by any new energy-producing technology such as low capital and operating costs and minimal environmental output.

  4. Analysing the role of fusion power in the future global energy system

    Science.gov (United States)

    Cabal, H.; Lechón, Y.; Ciorba, U.; Gracceva, F.; Eder, T.; Hamacher, T.; Lehtila, A.; Biberacher, M.; Grohnheit, P. E.; Ward, D.; Han, W.; Eherer, C.; Pina, A.

    2012-10-01

    This work presents the EFDA Times model (ETM), developed within the European Fusion Development Agreement (EFDA). ETM is an optimization global energy model which aims at providing the optimum energy system composition in terms of social wealth and sustainability including fusion as an alternative technology in the long term. Two framework scenarios are defined: a Base case scenario with no limits to CO2 emissions, and a 450ppm scenario with a limit of 450ppm in CO2-eq concentrations set by 2100. Previous results showed that in the Base case scenario, with no measures for CO2 emission reductions, fusion does not enter the energy system. However, when CO2 emission restrictions are imposed, the global energy system composition changes completely. In a 450ppm scenario, coal technologies disappear in a few decades, being mainly replaced by nuclear fission technologies which experience a great increase when constrained only by Uranium resources exhaustion. Fission technologies are then replaced by the fusion power plants that start in 2070, with a significant contribution to the global electricity production by 2100. To conclude the work, a sensitivity analysis will be presented on some parameters that may affect the possible role of fusion in the future global energy system. Note to the reader: The article number has been corrected on web pages on November 22, 2013.

  5. Analysing the role of fusion power in the future global energy system

    Directory of Open Access Journals (Sweden)

    Grohnheit P.E.

    2012-10-01

    Full Text Available This work presents the EFDA Times model (ETM, developed within the European Fusion Development Agreement (EFDA. ETM is an optimization global energy model which aims at providing the optimum energy system composition in terms of social wealth and sustainability including fusion as an alternative technology in the long term. Two framework scenarios are defined: a Base case scenario with no limits to CO2 emissions, and a 450ppm scenario with a limit of 450ppm in CO2-eq concentrations set by 2100. Previous results showed that in the Base case scenario, with no measures for CO2 emission reductions, fusion does not enter the energy system. However, when CO2 emission restrictions are imposed, the global energy system composition changes completely. In a 450ppm scenario, coal technologies disappear in a few decades, being mainly replaced by nuclear fission technologies which experience a great increase when constrained only by Uranium resources exhaustion. Fission technologies are then replaced by the fusion power plants that start in 2070, with a significant contribution to the global electricity production by 2100. To conclude the work, a sensitivity analysis will be presented on some parameters that may affect the possible role of fusion in the future global energy system.

  6. A tri-modality image fusion method for target delineation of brain tumors in radiotherapy.

    Directory of Open Access Journals (Sweden)

    Lu Guo

    Full Text Available To develop a tri-modality image fusion method for better target delineation in image-guided radiotherapy for patients with brain tumors.A new method of tri-modality image fusion was developed, which can fuse and display all image sets in one panel and one operation. And a feasibility study in gross tumor volume (GTV delineation using data from three patients with brain tumors was conducted, which included images of simulation CT, MRI, and 18F-fluorodeoxyglucose positron emission tomography (18F-FDG PET examinations before radiotherapy. Tri-modality image fusion was implemented after image registrations of CT+PET and CT+MRI, and the transparency weight of each modality could be adjusted and set by users. Three radiation oncologists delineated GTVs for all patients using dual-modality (MRI/CT and tri-modality (MRI/CT/PET image fusion respectively. Inter-observer variation was assessed by the coefficient of variation (COV, the average distance between surface and centroid (ADSC, and the local standard deviation (SDlocal. Analysis of COV was also performed to evaluate intra-observer volume variation.The inter-observer variation analysis showed that, the mean COV was 0.14(± 0.09 and 0.07(± 0.01 for dual-modality and tri-modality respectively; the standard deviation of ADSC was significantly reduced (p<0.05 with tri-modality; SDlocal averaged over median GTV surface was reduced in patient 2 (from 0.57 cm to 0.39 cm and patient 3 (from 0.42 cm to 0.36 cm with the new method. The intra-observer volume variation was also significantly reduced (p = 0.00 with the tri-modality method as compared with using the dual-modality method.With the new tri-modality image fusion method smaller inter- and intra-observer variation in GTV definition for the brain tumors can be achieved, which improves the consistency and accuracy for target delineation in individualized radiotherapy.

  7. Expression and activity analysis of a new fusion protein targeting ovarian cancer cells.

    Science.gov (United States)

    Su, Manman; Chang, Weiqin; Wang, Dingding; Cui, Manhua; Lin, Yang; Wu, Shuying; Xu, Tianmin

    2015-09-01

    The aim of the present study was to develop a new therapeutic drug to improve the prognosis of ovarian cancer patients. Human urokinase-type plasminogen activator (uPA)17-34-kunitz-type protease inhibitor (KPI) eukaryotic expression vector was constructed and recombinant human uPA17-34-KPI (rhuPA17-34-KPI) in P. pastoris was expressed. In the present study, the DNA sequences that encode uPA 17-34 amino acids were created according to the native amino acids sequence and inserted into the KPI-pPICZαC vector, which was constructed. Then, uPA17‑34-KPI-pPICZαC was transformed into P. pastoris X-33, and rhuPA17-34-KPI was expressed by induction of methanol. The bioactivities of a recombinant fusion protein were detected with trypsin inhibition analysis, and the inhibitory effects on the growth of ovarian cancer cells were identified using the TUNEL assay, in vitro wound‑healing assay and Matrigel model analysis. The results of the DNA sequence analysis of the recombinant vector uPA17-34-KPI‑pPICZα demonstrated that the DNA‑encoding human uPA 17-34 amino acids, 285-288 amino acids of amyloid precursor protein (APP) and 1-57 amino acids of KPI were correctly inserted into the pPICZαC vector. Following induction by methonal, the fusion protein with a molecular weight of 8.8 kDa was observed using SDS-PAGE and western blot analysis. RhuPA17-34-KPI was expressed in P. pastoris with a yield of 50 mg/l in a 50-ml tube. The recombinant fusion protein was able to inhibit the activity of trypsin, inhibit growth and induce apoptosis of SKOV3 cells, and inhibit the invasion and metastasis of ovarian cancer cells. By considering uPA17-34 amino acid specific binding uPAR as the targeted part of fusion protein and utilizing the serine protease inhibitor activity of KPI, it was found that the recombinant fusion protein uPA17-34-KPI inhibited the invasion and metastasis of ovarian tumors, and may therefore be regarded as effective in targeted treatment.

  8. A tri-modality image fusion method for target delineation of brain tumors in radiotherapy.

    Science.gov (United States)

    Guo, Lu; Shen, Shuming; Harris, Eleanor; Wang, Zheng; Jiang, Wei; Guo, Yu; Feng, Yuanming

    2014-01-01

    To develop a tri-modality image fusion method for better target delineation in image-guided radiotherapy for patients with brain tumors. A new method of tri-modality image fusion was developed, which can fuse and display all image sets in one panel and one operation. And a feasibility study in gross tumor volume (GTV) delineation using data from three patients with brain tumors was conducted, which included images of simulation CT, MRI, and 18F-fluorodeoxyglucose positron emission tomography (18F-FDG PET) examinations before radiotherapy. Tri-modality image fusion was implemented after image registrations of CT+PET and CT+MRI, and the transparency weight of each modality could be adjusted and set by users. Three radiation oncologists delineated GTVs for all patients using dual-modality (MRI/CT) and tri-modality (MRI/CT/PET) image fusion respectively. Inter-observer variation was assessed by the coefficient of variation (COV), the average distance between surface and centroid (ADSC), and the local standard deviation (SDlocal). Analysis of COV was also performed to evaluate intra-observer volume variation. The inter-observer variation analysis showed that, the mean COV was 0.14(± 0.09) and 0.07(± 0.01) for dual-modality and tri-modality respectively; the standard deviation of ADSC was significantly reduced (ptri-modality; SDlocal averaged over median GTV surface was reduced in patient 2 (from 0.57 cm to 0.39 cm) and patient 3 (from 0.42 cm to 0.36 cm) with the new method. The intra-observer volume variation was also significantly reduced (p = 0.00) with the tri-modality method as compared with using the dual-modality method. With the new tri-modality image fusion method smaller inter- and intra-observer variation in GTV definition for the brain tumors can be achieved, which improves the consistency and accuracy for target delineation in individualized radiotherapy.

  9. US Scientific Discory through Advanced Computing (SciDAC) Program & Fusion Energy Science

    Institute of Scientific and Technical Information of China (English)

    W. Tang

    2007-01-01

    @@ The development of a secure and reliable energy system that is environmentally and economically sustainable is a truly formidable scientific and technological challenge facing the world in the twenty-first century. This demands basic scientific understanding that can enable the innovations to make fusion energy practical.

  10. Calculating Transition Energy Barriers and Characterizing Activation States for Steps of Fusion.

    Science.gov (United States)

    Ryham, Rolf J; Klotz, Thomas S; Yao, Lihan; Cohen, Fredric S

    2016-03-08

    We use continuum mechanics to calculate an entire least energy pathway of membrane fusion, from stalk formation, to pore creation, and through fusion pore enlargement. The model assumes that each structure in the pathway is axially symmetric. The static continuum stalk structure agrees quantitatively with experimental stalk architecture. Calculations show that in a stalk, the distal monolayer is stretched and the stored stretching energy is significantly less than the tilt energy of an unstretched distal monolayer. The string method is used to determine the energy of the transition barriers that separate intermediate states and the dynamics of two bilayers as they pass through them. Hemifusion requires a small amount of energy independently of lipid composition, while direct transition from a stalk to a fusion pore without a hemifusion intermediate is highly improbable. Hemifusion diaphragm expansion is spontaneous for distal monolayers containing at least two lipid components, given sufficiently negative diaphragm spontaneous curvature. Conversely, diaphragms formed from single-component distal monolayers do not expand without the continual injection of energy. We identify a diaphragm radius, below which central pore expansion is spontaneous. For larger diaphragms, prior studies have shown that pore expansion is not axisymmetric, and here our calculations supply an upper bound for the energy of the barrier against pore formation. The major energy-requiring deformations in the steps of fusion are: widening of a hydrophobic fissure in bilayers for stalk formation, splay within the expanding hemifusion diaphragm, and fissure widening initiating pore formation in a hemifusion diaphragm.

  11. Investigation of heat of fusion storage for solar low energy buildings

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Furbo, Simon

    2005-01-01

    and xanthane rubber. The storage can cool down to surrounding temperature preserving the latent heat in form of the heat of fusion energy. The basis for the calculations is a super low energy house with a space heating demand of 2010 kWh/year and a domestic hot water demand of 2530 kWh/year. For storage...

  12. The addition of a sagittal image fusion improves the prostate cancer detection in a sensor-based MRI /ultrasound fusion guided targeted biopsy.

    Science.gov (United States)

    Günzel, Karsten; Cash, Hannes; Buckendahl, John; Königbauer, Maximilian; Asbach, Patrick; Haas, Matthias; Neymeyer, Jörg; Hinz, Stefan; Miller, Kurt; Kempkensteffen, Carsten

    2017-01-13

    To explore the diagnostic benefit of an additional image fusion of the sagittal plane in addition to the standard axial image fusion, using a sensor-based MRI/US fusion platform. During July 2013 and September 2015, 251 patients with at least one suspicious lesion on mpMRI (rated by PI-RADS) were included into the analysis. All patients underwent MRI/US targeted biopsy (TB) in combination with a 10 core systematic prostate biopsy (SB). All biopsies were performed on a sensor-based fusion system. Group A included 162 men who received TB by an axial MRI/US image fusion. Group B comprised 89 men in whom the TB was performed with an additional sagittal image fusion. The median age in group A was 67 years (IQR 61-72) and in group B 68 years (IQR 60-71). The median PSA level in group A was 8.10 ng/ml (IQR 6.05-14) and in group B 8.59 ng/ml (IQR 5.65-12.32). In group A the proportion of patients with a suspicious digital rectal examination (DRE) (14 vs. 29%, p = 0.007) and the proportion of primary biopsies (33 vs 46%, p = 0.046) were significantly lower. The rate of PI-RADS 3 lesions were overrepresented in group A compared to group B (19 vs. 9%; p = 0.044). Classified according to PI-RADS 3, 4 and 5, the detection rates of TB were 42, 48, 75% in group A and 25, 74, 90% in group B. The rate of PCa with a Gleason score ≥7 missed by TB was 33% (18 cases) in group A and 9% (5 cases) in group B; p-value 0.072. An explorative multivariate binary logistic regression analysis revealed that PI-RADS, a suspicious DRE and performing an additional sagittal image fusion were significant predictors for PCa detection in TB. 9 PCa were only detected by TB with sagittal fusion (sTB) and sTB identified 10 additional clinically significant PCa (Gleason ≥7). Performing an additional sagittal image fusion besides the standard axial fusion appears to improve the accuracy of the sensor-based MRI/US fusion platform.

  13. Fusion Energy Division annual progress report period ending December 31, 1983

    Energy Technology Data Exchange (ETDEWEB)

    1984-09-01

    The Fusion Program carries out work in a number of areas: (1) experimental and theoretical research on two magnetic confinement concepts - the ELMO Bumpy Torus (EBT) and the tokamak, (2) theoretical and engineering studies on a third concept - the stellarator, (3) engineering and physics of present-generation fusion devices, (4) development and testing of diagnostic tools and techniques, (5) development and testing of materials for fusion devices, (6) development and testing of the essential technologies for heating and fueling fusion plasmas, (7) development and testing of the superconducting magnets that will be needed to confine these plasmas, (8) design of future devices, (9) assessment of the environmental impact of fusion energy, and (10) assembly and distribution to the fusion community of data bases on atomic physics and radiation effects. The interactions between these activities and their integration into a unified program are major factors in the success of the individual activities, and the ORNL Fusion Program strives to maintain a balance among these activities that will lead to continued growth.

  14. Media analysis of the representations of fusion and other future energy technologies

    Energy Technology Data Exchange (ETDEWEB)

    Delicado, Ana; Schmidt, Luisa; Pereira, Sergio [Institute of Social Sciences of the University of Lisbon, Av. Prof. Anibal de Bettencourt, 9 1600-189 Lisbon (Portugal); Oltra, Christian; Prades, Ana [CISOT-CIEMAT. Gran Via de les Corts Catalanes 604, 4, 2, 08007 Barcelona (Spain)

    2015-07-01

    Media representations of energy have a relevant impact on public opinion and public support for investment in new energy sources. Fusion energy is one among several emerging energy technologies that requires a strong public investment on its research and development. This paper aims to characterise and compare the media representations of fusion and other emerging energy technologies in Portugal and in Spain. The emerging energy technologies selected for analysis are wave and tidal power, hydrogen, deep sea offshore wind power, energy applications of nanotechnology, bio-fuels from microalgae and IV generation nuclear fission. This work covered the news published in a selection of newspapers in Portugal and Spain between January 2007 and June 2013. (authors)

  15. Accurate Target Identification Using Multi-look Fusion of Low Quality Target Signatures

    Science.gov (United States)

    2008-12-01

    qualité, ce qui pourrait avoir des conséquences importantes pour les applications pratiques. D’une part, l’apparition de technologies de capteurs et...identification performance and this is not adequate for many target identification applications . Furthermore, in order for the single-look procedure to...obtenues qu’avec un un seul capteur . Toutefois, force est de constater que le rendement de l’identification correcte d’objectifs par l’approche

  16. Viral membrane fusion

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Stephen C., E-mail: harrison@crystal.harvard.edu

    2015-05-15

    Membrane fusion is an essential step when enveloped viruses enter cells. Lipid bilayer fusion requires catalysis to overcome a high kinetic barrier; viral fusion proteins are the agents that fulfill this catalytic function. Despite a variety of molecular architectures, these proteins facilitate fusion by essentially the same generic mechanism. Stimulated by a signal associated with arrival at the cell to be infected (e.g., receptor or co-receptor binding, proton binding in an endosome), they undergo a series of conformational changes. A hydrophobic segment (a “fusion loop” or “fusion peptide”) engages the target-cell membrane and collapse of the bridging intermediate thus formed draws the two membranes (virus and cell) together. We know of three structural classes for viral fusion proteins. Structures for both pre- and postfusion conformations of illustrate the beginning and end points of a process that can be probed by single-virion measurements of fusion kinetics. - Highlights: • Viral fusion proteins overcome the high energy barrier to lipid bilayer merger. • Different molecular structures but the same catalytic mechanism. • Review describes properties of three known fusion-protein structural classes. • Single-virion fusion experiments elucidate mechanism.

  17. Inertial Fusion Energy Development: What is Needed and What will be Learned at the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Hogan, W.J.

    1999-10-21

    Successful development of inertial fusion energy (IFE) requires that many technical issues be resolved. Separability of drivers, targets, chambers and other IFE power plant subsystems allows resolution of many of these issues in off-line facilities and programs. Periodically, major integrated facilities give a snapshot of the rate of progress toward the ultimate solutions. The National Ignition Facility (NIF) and Laser Megajoule (LMJ) are just such integrating facilities. This paper reviews the status of IFE development and projects what will be learned from the NIF and LMJ.

  18. FEASIBILITY OF HYDROGEN PRODUCTION USING LASER INERTIAL FUSION AS THE PRIMARY ENERGY SOURCE

    Energy Technology Data Exchange (ETDEWEB)

    Gorensek, M

    2006-11-03

    The High Average Power Laser (HAPL) program is developing technology for Laser IFE with the goal of producing electricity from the heat generated by the implosion of deuterium-tritium (DT) targets. Alternatively, the Laser IFE device could be coupled to a hydrogen generation system where the heat would be used as input to a water-splitting process to produce hydrogen and oxygen. The production of hydrogen in addition to electricity would allow fusion energy plants to address a much wider segment of energy needs, including transportation. Water-splitting processes involving direct and hybrid thermochemical cycles and high temperature electrolysis are currently being developed as means to produce hydrogen from high temperature nuclear fission reactors and solar central receivers. This paper explores the feasibility of this concept for integration with a Laser IFE plant, and it looks at potential modifications to make this approach more attractive. Of particular interest are: (1) the determination of the advantages of Laser IFE hydrogen production compared to other hydrogen production concepts, and (2) whether a facility of the size of FTF would be suitable for hydrogen production.

  19. The NASA-Lewis program on fusion energy for space power and propulsion, 1958-1978

    Science.gov (United States)

    Schulze, Norman R.; Roth, J. Reece

    1990-01-01

    An historical synopsis is provided of the NASA-Lewis research program on fusion energy for space power and propulsion systems. It was initiated to explore the potential applications of fusion energy to space power and propulsion systems. Some fusion related accomplishments and program areas covered include: basic research on the Electric Field Bumpy Torus (EFBT) magnetoelectric fusion containment concept, including identification of its radial transport mechanism and confinement time scaling; operation of the Pilot Rig mirror machine, the first superconducting magnet facility to be used in plasma physics or fusion research; operation of the Superconducting Bumpy Torus magnet facility, first used to generate a toroidal magnetic field; steady state production of neutrons from DD reactions; studies of the direct conversion of plasma enthalpy to thrust by a direct fusion rocket via propellant addition and magnetic nozzles; power and propulsion system studies, including D(3)He power balance, neutron shielding, and refrigeration requirements; and development of large volume, high field superconducting and cryogenic magnet technology.

  20. Comparative evaluation of solar, fission, fusion, and fossil energy resources, part 3

    Science.gov (United States)

    Clement, J. D.; Reupke, W. A.

    1974-01-01

    The role of nuclear fission reactors in becoming an important power source in the world is discussed. The supply of fissile nuclear fuel will be severely depleted by the year 2000. With breeder reactors the world supply of uranium could last thousands of years. However, breeder reactors have problems of a large radioactive inventory and an accident potential which could present an unacceptable hazard. Although breeder reactors afford a possible solution to the energy shortage, their ultimate role will depend on demonstrated safety and acceptable risks and environmental effects. Fusion power would also be a long range, essentially permanent, solution to the world's energy problem. Fusion appears to compare favorably with breeders in safety and environmental effects. Research comparing a controlled fusion reactor with the breeder reactor in solving our long range energy needs is discussed.

  1. Evolution of fusion hindrance for asymmetric systems at deep sub-barrier energies

    Science.gov (United States)

    Shrivastava, A.; Mahata, K.; Pandit, S. K.; Nanal, V.; Ichikawa, T.; Hagino, K.; Navin, A.; Palshetkar, C. S.; Parkar, V. V.; Ramachandran, K.; Rout, P. C.; Kumar, Abhinav; Chatterjee, A.; Kailas, S.

    2016-04-01

    Measurements of fusion cross-sections of 7Li and 12C with 198Pt at deep sub-barrier energies are reported to unravel the role of the entrance channel in the occurrence of fusion hindrance. The onset of fusion hindrance has been clearly observed in 12C +198Pt system but not in 7Li +198Pt system, within the measured energy range. Emergence of the hindrance, moving from lighter (6,7Li) to heavier (12C, 16O) projectiles is explained employing a model that considers a gradual transition from a sudden to adiabatic regime at low energies. The model calculation reveals a weak effect of the damping of coupling to collective motion for the present systems as compared to that obtained for systems with heavier projectiles.

  2. Evolution of fusion hindrance for asymmetric systems at deep sub barrier energies

    CERN Document Server

    Shrivastavaa, A; Pandit, S K; Nanal, V; Ichikawa, T; Hagino, K; Navin, A; Palshetkar, C S; Parkar, V V; Ramachandran, K; Rout, P C; Kumar, Abhinav; Chatterjee, A; Kailas, S

    2016-01-01

    Measurements of fusion cross-sections of 7Li and 12C with 198Pt at deep sub-barrier energies are reported to unravel the role of the entrance channel in the occurrence of fusion hindrance. The onset of fusion hindrance has been clearly observed in 12C + 198Pt system but not in 7Li + 198Pt system, within the measured energy range. Emergence of the hindrance, moving from lighter (6,7Li) to heavier (12C,16O) projectiles is explained employing a model that considers a gradual transition from a sudden to adiabatic regime at low energies. The model calculation reveals a weak effect of the damping of coupling to collective motion for the present systems as compared to that obtained for systems with heavier projectiles.

  3. High-Yield Lithium-Injection Fusion-Energy (HYLIFE) reactor

    Energy Technology Data Exchange (ETDEWEB)

    Blink, J.A.; Hogam, W.J.; Hovingh, J.; Meier, E.R.; Pitts, J.H. (comps.)

    1985-12-23

    The High-Yield Lithium-Injection Fusion Energy (HYLIFE) concept to convent inertial confinement fusion energy into electric power has undergone intensive research and refinement at LLNL since 1978. This paper reports on the final HYLIFE design, focusing on five major areas: the HYLIFE reaction chamber (which includes neutronics, liquid-metal jet-array hydrocynamics, and structural design), supporting systems, primary steam system and balance of plant, safety and environmental protection, and costs. An annotated bibliography of reports applicable to HYLIFE is also provided. We conclude that HYLIFE is a particularly viable concept for the safe, clean production of electrical energy. The liquid-metal jet array, HYLIFE's key design feature, protects the surrounding structural components from x-rays, fusion fuel-pellet debris, neutron damage and activation, and high temperatures and stresses, allowing the structure to last for the plant's entire 30-year lifetime without being replaced. 127 refs., 18 figs.

  4. Evolution of fusion hindrance for asymmetric systems at deep sub-barrier energies

    Directory of Open Access Journals (Sweden)

    A. Shrivastava

    2016-04-01

    Full Text Available Measurements of fusion cross-sections of 7Li and 12C with 198Pt at deep sub-barrier energies are reported to unravel the role of the entrance channel in the occurrence of fusion hindrance. The onset of fusion hindrance has been clearly observed in C12+Pt198 system but not in Li7+Pt198 system, within the measured energy range. Emergence of the hindrance, moving from lighter (6,7Li to heavier (12C, 16O projectiles is explained employing a model that considers a gradual transition from a sudden to adiabatic regime at low energies. The model calculation reveals a weak effect of the damping of coupling to collective motion for the present systems as compared to that obtained for systems with heavier projectiles.

  5. Barrier distributions and signatures of transfer channels in the Ca40+Ni58,64 fusion reactions at energies around and below the Coulomb barrier

    Science.gov (United States)

    Bourgin, D.; Courtin, S.; Haas, F.; Stefanini, A. M.; Montagnoli, G.; Goasduff, A.; Montanari, D.; Corradi, L.; Fioretto, E.; Huiming, J.; Scarlassara, F.; Rowley, N.; Szilner, S.; Mijatović, T.

    2014-10-01

    Background: The nuclear structure of colliding nuclei is known to influence the fusion process. Couplings of the relative motion to nuclear shape deformations and vibrations lead to an enhancement of the sub-barrier fusion cross section in comparison with the predictions of one-dimensional barrier penetration models. This enhancement is explained by coupled-channels calculations including these couplings. The sub-barrier fusion cross section is also affected by nucleon transfer channels between the colliding nuclei. Purpose: The aim of the present experiment is to investigate the influence of the projectile and target nuclear structures on the fusion cross sections in the Ca40+Ni58 and Ca40+Ni64 systems. Methods: The experimental and theoretical fusion excitation functions as well as the barrier distributions were compared for these two systems. Coupled-channels calculations were performed using the ccfull code. Results: Good agreement was found between the measured and calculated fusion cross sections for the Ca40+Ni58 system. The situation is different for the Ca40+Ni64 system where the coupled-channels calculations with no nucleon transfer clearly underestimate the fusion cross sections below the Coulomb barrier. The fusion excitation function was, however, well reproduced at low and high energies by including the coupling to the neutron pair-transfer channel in the calculations. Conclusions: The nuclear structure of the colliding nuclei influences the fusion cross sections below the Coulomb barrier for both Ca40+Ni58,64 systems. Moreover, we highlighted the effect of the neutron pair-transfer channel on the fusion cross sections in Ca40+Ni64.

  6. 5-Fluorocytosine combined with Fcy-hEGF fusion protein targets EGFR-expressing cancer cells

    Energy Technology Data Exchange (ETDEWEB)

    Lan, Keng-Hsueh [Division of Radiation Oncology, Department of Oncology, National Taiwan University Hospital, Taipei 100, Taiwan (China); Shih, Yi-Sheng [Cancer Center, Taipei Veterans General Hospital, Taipei 112, Taiwan (China); Chang, Cheng Allen [Department of Biomedical Imaging and Radiological Sciences, National Yang-Ming University, Taipei 112, Taiwan (China); School of Biomedical Science and Engineering, National Yang-Ming University, Taipei 112, Taiwan (China); Yen, Sang-Hue [Cancer Center, Taipei Veterans General Hospital, Taipei 112, Taiwan (China); Department of Biomedical Imaging and Radiological Sciences, National Yang-Ming University, Taipei 112, Taiwan (China); Lan, Keng-Li, E-mail: kllan@vghtpe.gov.tw [Cancer Center, Taipei Veterans General Hospital, Taipei 112, Taiwan (China); Department of Biomedical Imaging and Radiological Sciences, National Yang-Ming University, Taipei 112, Taiwan (China)

    2012-11-16

    Highlights: Black-Right-Pointing-Pointer EGFR-expressing epithelial cancers account for significant portion of cancer deaths. Black-Right-Pointing-Pointer EGF-EGFR signaling pathway is validated as an important anticancer drug target. Black-Right-Pointing-Pointer EGF and Fcy fusion protein (Fcy-hEGF) can bind to EGFR and convert 5-FC to 5-FU. Black-Right-Pointing-Pointer Fcy-hEGF combined with 5-FC preferentially inhibits EGFR-expressing cells viability. -- Abstract: Human epithelial cancers account for approximately 50% of all cancer deaths. This type of cancer is characterized by excessive activation and expression of the epidermal growth factor receptor (EGFR). The EGFR pathway is critical for cancer cell proliferation, survival, metastasis and angiogenesis. The EGF-EGFR signaling pathway has been validated as an important anticancer drug target. Increasing numbers of targeted therapies against this pathway have been either approved or are currently under development. Here, we adopted a prodrug system that uses 5-fluorocytosine (5-FC) and human EGF (hEGF) fused with yeast cytosine deaminase (Fcy) to target EGFR-overexpressing cancer cells and to convert 5-FC to a significantly more toxic chemotherapeutic, 5-fluorouracil (5-FU). We cloned and purified the Fcy-hEGF fusion protein from Pichia pastoris yeast. This fusion protein specifically binds to EGFR with a similar affinity as hEGF, approximately 10 nM. Fcy-hEGF binds tightly to A431 and MDA-MB-468 cells, which overexpress EGFR, but it binds with a lower affinity to MDA-MB-231 and MCF-7, which express lower levels of EGFR. Similarly, the viability of EGFR-expressing cells was suppressed by Fcy-hEGF in the presence of increasing concentrations of 5-FC, and the IC{sub 50} values for A431 and MDA-MB-468 were approximately 10-fold lower than those of MDA-MB-231 and MCF-7. This novel prodrug system, Fcy-hEGF/5-FC, might represent a promising addition to the available class of inhibitors that specifically target EGFR

  7. Heavy-ion fusion and scattering with Skyrme energy density functional

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    In our recent studies,an empirical barrier distribution was proposed for a unified description of the fusion cross sections of light and medium-heavy fusion systems,the capture cross sections of the reactions leading to superheavy nuclei,and the large-angle quasi-elastic scattering cross sections based on the Skyrme energy-density functional approach.In this paper,we first give a brief review of these results.Then,by examining the barrier distributions in detail,we find that the fusion cross sections depend more strongly on the shape of the left side of the barrier distribution while the quasi-elastic scattering cross sections depend more strongly on the right side.Furthermore,by combining these studies and the HIVAP calculations for the survival probability,the formation probability of the compound nucleus is deduced from the measured evaporation residue cross sections for "cold" and "hot" fusion reactions.

  8. Role of anharmonicities of nuclear vibrations in fusion reactions at subbarrier energies

    CERN Document Server

    Hagino, K; Kuyucak, S

    1997-01-01

    We discuss the effects of double octupole and quadrupole phonon excitations in $^{144}$Sm on fusion reactions between $^{16}$O and $^{144}$Sm at subbarrier energies. The effects of anharmonicities of the vibrational states are taken into account by using the $sdf$-interacting boson model. We compare the results with those in the harmonic limit to show that anharmonicities play an essential role in reproducing the experimental fusion barrier distribution. From the analysis of the high quality fusion data available for this system, we deduce negative static quadrupole moments for both the first 2$^{+}$ and 3$^{-}$ states in $^{144}$Sm. This is the first time that the sign of static quadrupole moments of phonon states in a spherical nucleus is determined from the data of subbarrier fusion reactions.

  9. Fusion energy division annual progress report, period ending December 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-11-01

    The ORNL Program encompasses most aspects of magnetic fusion research including research on two magnetic confinement programs (tokamaks and ELMO bumpy tori); the development of the essential technologies for plasma heating, fueling, superconducting magnets, and materials; the development of diagnostics; the development of atomic physics and radiation effect data bases; the assessment of the environmental impact of magnetic fusion; the physics and engineering of present-generation devices; and the design of future devices. The integration of all of these activities into one program is a major factor in the success of each activity. An excellent example of this integration is the extremely successful application of neutral injection heating systems developed at ORNL to tokamaks both in the Fusion Energy Division and at Princeton Plasma Physics Laboratory (PPPL). The goal of the ORNL Fusion Program is to maintain this balance between plasma confinement, technology, and engineering activities.

  10. Indirect-drive inertial fusion targets for two-sided heavy-ion illumination

    Science.gov (United States)

    Remizov, G. N.; Romanov, Yu. A.; Ryabikina, N. A.; Shagaliev, R. M.; Vakhlamova, L. L.; Vatulin, V. V.; Vinokurov, O. A.; Bock, R.; Kang, K.-H.; Maruhn, J. A.

    The properties of heavy-ion induced fusion targets with two-sided illumination and with the converters placed completely inside the hohlraum have been investigated using integrated simulations based on the SATURN and MIMOZA code packages in order to check the results obtained with the view factor method in previous work, which is briefly reviewed. Separate converter simulations show the importance of an accurate treatment of radiation transport and also demonstrate that a converter efficiency of 40 - 80% can be achieved easily depending on the detailed converter material and geometry. For the complete target, a gas fill is shown to be necessary and it turned out to be very important to allow some of the radiation shields to become partially transparent during the evolution. In the most favorable case, an asymmetry in the temperature on the capsule of about 5% was achieved, leading to a reduction of the neutron yield by a factor of 7 compared to an ideally symmetric situation.

  11. Inertial confinement fusion target; Confinement inertiel d'une cible magnetisee

    Energy Technology Data Exchange (ETDEWEB)

    Bourdier, A

    2001-12-01

    A simple, zero-dimensional model describing the temporal behaviour of an imploding-shell, magnetized fuel inertial confinement fusion target is formulated. The addition of a magnetic field to the fuel reduces thermal conduction losses. As a consequence, it might lead to high gains and reduce the driver requirements. This beneficial effect of the magnetic field on thermonuclear gains is confirmed qualitatively by the zero-dimensional model results. Still, the extent of the initial-condition space for which significant gains can occur is not, by far, as large as previously reported. One-dimensional CEA code simulations which confirm this results are also presented. Finally, we suggest to study the approach proposed by Hasegawa. In this scheme, the laser target is not imploded, and the life-time of the plasma can be very much increased. (author)

  12. Contributions of complete fusion and break-up–fusion to intermediate mass fragment production in the low energy interaction of 12C and 27Al

    CERN Document Server

    Förtsch, S V; Colleoni, P; Gadioli, E; Gadioli Erba, E; Mairani, A; Steyn, G F; Lawrie, J J; Smit, F D; Connell, S H; Fearick, R W; Thovhogi, T

    2007-01-01

    The measured spectra of a large number of intermediate mass fragments produced at a CM energy of about 110 MeV in the 27Al(12C, x) reaction as well as in its inverse reaction, 12C(27Al, x), are presented. The analysis of these data suggests that, at this energy, the main reaction mechanisms which contribute to the intermediate mass fragment emission are two-nucleus complete fusion and break-up–fusion reactions.

  13. DIII-D research to address key challenges for ITER and fusion energy

    Science.gov (United States)

    Buttery, R. J.; the DIII-D Team

    2015-10-01

    DIII-D has made significant advances in the scientific basis for fusion energy. The physics mechanism of resonant magnetic perturbation (RMP) edge localized mode (ELM) suppression is revealed as field penetration at the pedestal top, and reduced coil set operation was demonstrated. Disruption runaway electrons were effectively quenched by shattered pellets; runaway dissipation is explained by pitch angle scattering. Modest thermal quench radiation asymmetries are well described NIMROD modelling. With good pedestal regulation and error field correction, low torque ITER baselines have been demonstrated and shown to be compatible with an ITER test blanket module simulator. However performance and long wavelength turbulence degrade as low rotation and electron heating are approached. The alternative QH mode scenario is shown to be compatible with high Greenwald density fraction, with an edge harmonic oscillation demonstrating good impurity flushing. Discharge optimization guided by the EPED model has discovered a new super H-mode with doubled pedestal height. Lithium injection also led to wider, higher pedestals. On the path to steady state, 1 MA has been sustained fully noninductively with βN = 4 and RMP ELM suppression, while a peaked current profile scenario provides attractive options for ITER and a βN = 5 future reactor. Energetic particle transport is found to exhibit a critical gradient behaviour. Scenarios are shown to be compatible with radiative and snowflake divertor techniques. Physics studies reveal that the transition to H mode is locked in by a rise in ion diamagnetic flows. Intrinsic rotation in the plasma edge is demonstrated to arise from kinetic losses. New 3D magnetic sensors validate linear ideal MHD, but identify issues in nonlinear simulations. Detachment, characterized in 2D with sub-eV resolution, reveals a radiation shortfall in simulations. Future facility development targets burning plasma physics with torque free electron heating, the

  14. The National Ignition Facility: Status and Plans for Laser Fusion and High-Energy-Density Experimental Studies

    Energy Technology Data Exchange (ETDEWEB)

    Moses, E I

    2002-01-11

    The National Ignition Facility (NIF), currently under construction at the University of California's Lawrence Livermore National Laboratory is a $2.25B stadium-sized facility containing a 192-beam, 1.8-Megajoule, 500-Terawatt, 351-nm laser system. NIF is being built by the National Nuclear Security Agency and when completed will be the world's largest laser system, providing a national center to study inertial confinement fusion and the physics of extreme energy densities and pressures. In NIF up to 192 energetic laser beams will compress small fusion targets to conditions where they will ignite and burn, liberating more energy than is required to initiate the fusion reactions. NIF experiments will allow the study of physical processes at temperatures approaching 100 million K and 100 billion times atmospheric pressure. These conditions exist naturally only in the interior of stars and in nuclear weapons explosions. In the course of designing the world's most energetic laser system, a number of significant technology breakthroughs have been achieved. Research is also underway to develop a shorter pulse capability on NIF for high power applications. We discuss here the technology challenges and solutions that have made NIF possible along with enhancements to NIF's design that could lead to exawatt power levels.

  15. Study on the Feasibility of Direct Fusion Energy Conversion for Deep-Space Propulsion

    Science.gov (United States)

    Tarditi, Alfonso G.; Miley, George H.; Scott, John H.

    2012-10-01

    A significant change in the current space mission capabilities can be achieved with a highly efficient integration of a fusion energy source with an advanced space propulsion thruster, both with low specific mass. With aneutronic nuclear fusion as the high-density primary energy source, this study considers first electric energy extraction from the fusion reaction products via direct energy conversion to recirculate power as required for the operation of the fusion core. Then the beam of remaining reaction products is conditioned to achieve the optimal thrust and specific impulse for the mission. The research is specifically focused on two key issues: (i) Efficiency improvement of a Traveling Wave Direct Energy Converter (TWDEC, [1]) by achieving a higher ion beam density and optimization of the electrode coupling and of the neutralizing electron flow. (ii) A fast-particle kinetic energy-to-thrust conversion process based on collective interaction between ion bunches well separated in space [2]. Computer simulation results and a design for a basic physics experiment currently under development are reported. [4pt] [1] H. Momota et al., Fus. Tech., 35, 60(1999)[0pt] [2] A. G. Tarditi et al. Proc. NETS 2012 Conf., Woodlands, TX (2012)

  16. Report of the Integrated Program Planning Activity for the DOE Fusion Energy Sciences Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-12-01

    This report of the Integrated Program Planning Activity (IPPA) has been prepared in response to a recommendation by the Secretary of Energy Advisory Board that, ''Given the complex nature of the fusion effort, an integrated program planning process is an absolute necessity.'' We, therefore, undertook this activity in order to integrate the various elements of the program, to improve communication and performance accountability across the program, and to show the inter-connectedness and inter-dependency of the diverse parts of the national fusion energy sciences program. This report is based on the September 1999 Fusion Energy Sciences Advisory Committee's (FESAC) report ''Priorities and Balance within the Fusion Energy Sciences Program''. In its December 5,2000, letter to the Director of the Office of Science, the FESAC has reaffirmed the validity of the September 1999 report and stated that the IPPA presents a framework and process to guide the achievement of the 5-year goals listed in the 1999 report. The National Research Council's (NRC) Fusion Assessment Committee draft final report ''An Assessment of the Department of Energy's Office of Fusion Energy Sciences Program'', reviewing the quality of the science in the program, was made available after the IPPA report had been completed. The IPPA report is, nevertheless, consistent with the recommendations in the NRC report. In addition to program goals and the related 5-year, 10-year, and 15-year objectives, this report elaborates on the scientific issues associated with each of these objectives. The report also makes clear the relationships among the various program elements, and cites these relationships as the reason why integrated program planning is essential. In particular, while focusing on the science conducted by the program, the report addresses the important balances between the science and energy goals of the program, between the

  17. Comparative study of fusion barriers using Skyrme interactions and the energy density functional

    Science.gov (United States)

    Ghodsi, O. N.; Torabi, F.

    2015-12-01

    Using different Skyrme interactions, we have carried out a comparative analysis of fusion barriers for a wide range of interacting nuclei in the framework of semiclassical Skyrme energy density formalism. The results of our calculations reveal that SVI, SII, and SIII Skyrme forces are able to reproduce the empirical values of barrier heights with higher accuracy than the other considered forces in this formalism. It is also shown that the calculated nucleus-nucleus potentials derived from such Skyrme interactions are able to explain the fusion cross sections at energies near and above the barrier.

  18. Comparative study of fusion barriers using Skyrme interactions and the energy density functional

    CERN Document Server

    Ghodsi, O N

    2015-01-01

    Using different Skyrme interactions, we have carried out a comparative analysis of fusion barriers for a wide range of interacting nuclei in the framework of semiclassical Skyrme energy density formalism. The results of our calculations reveal that SVI, SII, and SIII Skyrme forces are able to reproduce the empirical values of barrier heights with higher accuracy than the other considered forces in this formalism. It is also shown that the calculated nucleus-nucleus potentials derived from such Skyrme interactions are able to explain the fusion cross sections at energies near and above the barrier.

  19. Identification of target genes of synovial sarcoma-associated fusion oncoprotein using human pluripotent stem cells

    Energy Technology Data Exchange (ETDEWEB)

    Hayakawa, Kazuo [Department of Tissue Regeneration, Institute for Frontier Medical Sciences, Kyoto University, Kyoto (Japan); Department of Cell Growth and Differentiation, Center for iPS Cell Research and Application, Kyoto University, Kyoto (Japan); Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Nagoya City University, Nagoya (Japan); Ikeya, Makoto [Department of Cell Growth and Differentiation, Center for iPS Cell Research and Application, Kyoto University, Kyoto (Japan); Fukuta, Makoto [Department of Tissue Regeneration, Institute for Frontier Medical Sciences, Kyoto University, Kyoto (Japan); Department of Cell Growth and Differentiation, Center for iPS Cell Research and Application, Kyoto University, Kyoto (Japan); Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Nagoya City University, Nagoya (Japan); Woltjen, Knut [Department of Reprogramming Sciences, Center for iPS Cell Research and Application, Kyoto University, Kyoto (Japan); Tamaki, Sakura; Takahara, Naoko; Kato, Tomohisa; Sato, Shingo [Department of Tissue Regeneration, Institute for Frontier Medical Sciences, Kyoto University, Kyoto (Japan); Otsuka, Takanobu [Department of Orthopaedic Surgery, Graduate School of Medical Sciences, Nagoya City University, Nagoya (Japan); Toguchida, Junya, E-mail: togjun@frontier.kyoto-u.ac.jp [Department of Tissue Regeneration, Institute for Frontier Medical Sciences, Kyoto University, Kyoto (Japan); Department of Cell Growth and Differentiation, Center for iPS Cell Research and Application, Kyoto University, Kyoto (Japan); Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto (Japan)

    2013-03-22

    Highlights: ► We tried to identify targets of synovial sarcoma (SS)-associated SYT–SSX fusion gene. ► We established pluripotent stem cell (PSC) lines with inducible SYT–SSX gene. ► SYT–SSX responsive genes were identified by the induction of SYT–SSX in PSC. ► SS-related genes were selected from database by in silico analyses. ► 51 genes were finally identified among SS-related genes as targets of SYT–SSX in PSC. -- Abstract: Synovial sarcoma (SS) is a malignant soft tissue tumor harboring chromosomal translocation t(X; 18)(p11.2; q11.2), which produces SS-specific fusion gene, SYT–SSX. Although precise function of SYT–SSX remains to be investigated, accumulating evidences suggest its role in gene regulation via epigenetic mechanisms, and the product of SYT–SSX target genes may serve as biomarkers of SS. Lack of knowledge about the cell-of-origin of SS, however, has placed obstacle in the way of target identification. Here we report a novel approach to identify SYT–SSX2 target genes using human pluripotent stem cells (hPSCs) containing a doxycycline-inducible SYT–SSX2 gene. SYT–SSX2 was efficiently induced both at mRNA and protein levels within three hours after doxycycline administration, while no morphological change of hPSCs was observed until 24 h. Serial microarray analyses identified genes of which the expression level changed more than twofold within 24 h. Surprisingly, the majority (297/312, 95.2%) were up-regulated genes and a result inconsistent with the current concept of SYT–SSX as a transcriptional repressor. Comparing these genes with SS-related genes which were selected by a series of in silico analyses, 49 and 2 genes were finally identified as candidates of up- and down-regulated target of SYT–SSX, respectively. Association of these genes with SYT–SSX in SS cells was confirmed by knockdown experiments. Expression profiles of SS-related genes in hPSCs and human mesenchymal stem cells (hMSCs) were strikingly

  20. BOOK REVIEW: Inertial confinement fusion: The quest for ignition and energy gain using indirect drive

    Science.gov (United States)

    Yamanaka, C.

    1999-06-01

    Inertial confinement fusion (ICF) is an alternative way to control fusion which is based on scaling down a thermonuclear explosion to a small size, applicable for power production, a kind of thermonuclear internal combustion engine. This book extends many interesting topics concerning the research and development on ICF of the last 25 years. It provides a systematic development of the physics basis and also various experimental data on radiation driven implosion. This is a landmark treatise presented at the right time. It is based on the article ``Development of the indirect-drive approach to inertial confinement fusion and the target physics basis for ignition and gain'' by J.D. Lindl, published in Physics of Plasmas, Vol. 2, November 1995, pp. 3933-4024. As is well known, in the United States of America research on the target physics basis for indirect drive remained largely classified until 1994. The indirect drive approaches were closely related to nuclear weapons research at Lawrence Livermore and Los Alamos National Laboratories. In Japan and other countries, inertial confinement fusion research for civil energy has been successfully performed to achieve DT fuel pellet compression up to 1000 times normal density, and indirect drive concepts, such as the `Cannon Ball' scheme, also prevailed at several international conferences. In these circumstances the international fusion community proposed the Madrid Manifesto in 1988, which urged openness of ICF information to promote international collaboration on civil energy research for the future resources of the human race. This proposal was also supported by some of the US scientists. The United States Department of Energy revised its classification guidelines for ICF six years after the Madrid Manifesto. This first book from the USA treating target physics issues, covering topics from implosion dynamics to hydrodynamic stability, ignition physics, high-gain target design and the scope for energy applications is

  1. Log-Gabor energy based multimodal medical image fusion in NSCT domain.

    Science.gov (United States)

    Yang, Yong; Tong, Song; Huang, Shuying; Lin, Pan

    2014-01-01

    Multimodal medical image fusion is a powerful tool in clinical applications such as noninvasive diagnosis, image-guided radiotherapy, and treatment planning. In this paper, a novel nonsubsampled Contourlet transform (NSCT) based method for multimodal medical image fusion is presented, which is approximately shift invariant and can effectively suppress the pseudo-Gibbs phenomena. The source medical images are initially transformed by NSCT followed by fusing low- and high-frequency components. The phase congruency that can provide a contrast and brightness-invariant representation is applied to fuse low-frequency coefficients, whereas the Log-Gabor energy that can efficiently determine the frequency coefficients from the clear and detail parts is employed to fuse the high-frequency coefficients. The proposed fusion method has been compared with the discrete wavelet transform (DWT), the fast discrete curvelet transform (FDCT), and the dual tree complex wavelet transform (DTCWT) based image fusion methods and other NSCT-based methods. Visually and quantitatively experimental results indicate that the proposed fusion method can obtain more effective and accurate fusion results of multimodal medical images than other algorithms. Further, the applicability of the proposed method has been testified by carrying out a clinical example on a woman affected with recurrent tumor images.

  2. Log-Gabor Energy Based Multimodal Medical Image Fusion in NSCT Domain

    Directory of Open Access Journals (Sweden)

    Yong Yang

    2014-01-01

    Full Text Available Multimodal medical image fusion is a powerful tool in clinical applications such as noninvasive diagnosis, image-guided radiotherapy, and treatment planning. In this paper, a novel nonsubsampled Contourlet transform (NSCT based method for multimodal medical image fusion is presented, which is approximately shift invariant and can effectively suppress the pseudo-Gibbs phenomena. The source medical images are initially transformed by NSCT followed by fusing low- and high-frequency components. The phase congruency that can provide a contrast and brightness-invariant representation is applied to fuse low-frequency coefficients, whereas the Log-Gabor energy that can efficiently determine the frequency coefficients from the clear and detail parts is employed to fuse the high-frequency coefficients. The proposed fusion method has been compared with the discrete wavelet transform (DWT, the fast discrete curvelet transform (FDCT, and the dual tree complex wavelet transform (DTCWT based image fusion methods and other NSCT-based methods. Visually and quantitatively experimental results indicate that the proposed fusion method can obtain more effective and accurate fusion results of multimodal medical images than other algorithms. Further, the applicability of the proposed method has been testified by carrying out a clinical example on a woman affected with recurrent tumor images.

  3. Site-specific modification of ED-B-targeting antibody using intein-fusion technology

    Directory of Open Access Journals (Sweden)

    Greven Simone

    2011-07-01

    Full Text Available Abstract Background A promising new approach in cancer therapy is the use of tumor specific antibodies coupled to cytotoxic agents. Currently these immunoconjugates are prepared by rather unspecific coupling chemistries, resulting in heterogeneous products. As the drug load is a key parameter for the antitumor activity, site-specific strategies are desired. Expressed protein ligation (EPL and protein trans-splicing (PTS are methods for the specific C-terminal modification of a target protein. Both include the expression as an intein fusion protein, followed by the exchange of the intein for a functionalized moiety. Results A full-length IgG specific for fibronectin ED-B was expressed as fusion protein with an intein (Mxe GyrA or Npu DnaE attached to each heavy chain. In vitro protocols were established to site-specifically modify the antibodies in high yields by EPL or PTS, respectively. Although reducing conditions had to be employed during the process, the integrity or affinity of the antibody was not affected. The protocols were used to prepare immunoconjugates containing two biotin molecules per antibody, attached to the C-termini of the heavy chains. Conclusion Full-length antibodies can be efficiently and site-specifically modified at the C-termini of their heavy chains by intein-fusion technologies. The described protocols can be used to prepare immunoconjugates of high homogeneity and with a defined drug load of two. The attachment to the C-termini is expected to retain the affinity and effector functions of the antibodies.

  4. A mechanistic paradigm for broad-spectrum antivirals that target virus-cell fusion.

    Directory of Open Access Journals (Sweden)

    Frederic Vigant

    Full Text Available LJ001 is a lipophilic thiazolidine derivative that inhibits the entry of numerous enveloped viruses at non-cytotoxic concentrations (IC50 ≤ 0.5 µM, and was posited to exploit the physiological difference between static viral membranes and biogenic cellular membranes. We now report on the molecular mechanism that results in LJ001's specific inhibition of virus-cell fusion. The antiviral activity of LJ001 was light-dependent, required the presence of molecular oxygen, and was reversed by singlet oxygen ((1O2 quenchers, qualifying LJ001 as a type II photosensitizer. Unsaturated phospholipids were the main target modified by LJ001-generated (1O2. Hydroxylated fatty acid species were detected in model and viral membranes treated with LJ001, but not its inactive molecular analog, LJ025. (1O2-mediated allylic hydroxylation of unsaturated phospholipids leads to a trans-isomerization of the double bond and concurrent formation of a hydroxyl group in the middle of the hydrophobic lipid bilayer. LJ001-induced (1O2-mediated lipid oxidation negatively impacts on the biophysical properties of viral membranes (membrane curvature and fluidity critical for productive virus-cell membrane fusion. LJ001 did not mediate any apparent damage on biogenic cellular membranes, likely due to multiple endogenous cytoprotection mechanisms against phospholipid hydroperoxides. Based on our understanding of LJ001's mechanism of action, we designed a new class of membrane-intercalating photosensitizers to overcome LJ001's limitations for use as an in vivo antiviral agent. Structure activity relationship (SAR studies led to a novel class of compounds (oxazolidine-2,4-dithiones with (1 100-fold improved in vitro potency (IC50<10 nM, (2 red-shifted absorption spectra (for better tissue penetration, (3 increased quantum yield (efficiency of (1O2 generation, and (4 10-100-fold improved bioavailability. Candidate compounds in our new series moderately but significantly (p≤0

  5. Understanding of Edge Plasmas in Magnetic Fusion Energy Devices

    Energy Technology Data Exchange (ETDEWEB)

    Rognlien, T

    2004-11-01

    A limited overview is given of the theoretical understanding of edge plasmas in fusion devices. This plasma occupies the thin region between the hot core plasma and material walls in magnetically confinement configurations. The region is often formed by a change in magnetic topology from close magnetic field lines (i.e., the core region) and open field lines that contact material surfaces (i.e., the scrape-off layer [SOL]), with the most common example being magnetically diverted tokamaks. The physics of this region is determined by the interaction of plasma with neutral gas in the presence of plasma turbulence, with impurity radiation being an important component. Recent advances in modeling strong, intermittent micro-turbulent edge-plasma transport is given, and the closely coupled self-consistent evolution of the edge-plasma profiles in tokamaks. In addition, selected new results are given for the characterization of edge-plasmas behavior in the areas of edge-pedestal relaxation and SOL transport via Edge-Localize Modes (ELMs), impurity formation including dust, and magnetic field-line stochasticity in tokamaks.

  6. Identification of a human protein-derived HIV-1 fusion inhibitor targeting the gp41 fusion core structure.

    Directory of Open Access Journals (Sweden)

    Lijun Chao

    Full Text Available The HIV-1 envelope glycoprotein (Env gp41 plays a crucial role in the viral fusion process. The peptides derived from the C-terminal heptad repeat (CHR of gp41 are potent HIV fusion inhibitors. However, the activity of these anti-HIV-1 peptides in vivo may be attenuated by their induction of anti-gp41 antibodies. Thus, it is essential to identify antiviral peptides or proteins with low, or no, immunogenicity to humans. Here, we found that the C-terminal fragment (aa 462-521 of the human POB1 (the partner of RalBP1, designated C60, is an HIV-1 fusion inhibitor. It bound to N36, the peptide derived from the N-terminal heptad repeat (NHR of gp41, and to the six-helix bundle (6-HB formed by N36 and C34, a CHR-peptide, but it did not bind to C34. Unlike the CHR-peptides, C60 did not block gp41 6-HB formation. Rather, results suggest that C60 inhibits HIV-1 fusion by binding to the 6-HB, in particular, the residues in the gp41 NHR domain that are exposed on the surface of 6-HB. Since 6-HB plays a crucial role in the late stage of fusion between the viral envelope and endosomal membrane during the endocytic process of HIV-1, C60 may serve as a host restriction factor to suppress HIV-1 entry into CD4+ T lymphocytes. Taken together, it can be concluded from these results that C60 can be used as a lead for the development of anti-HIV-1 therapeutics or microbicides for the treatment and prevention of HIV-1 infection, as well as a molecular probe to study the fusogenic mechanism of HIV-1.

  7. Elastic, excitation, ionization and charge transfer cross sections of current interest in fusion energy research

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, D.R.; Krstic, P.S. [Oak Ridge National Lab. TN (United States). Physics Div.

    1997-01-01

    Due to the present interest in modeling and diagnosing the edge and divertor plasma regions in magnetically confined fusion devices, we have sought to provide new calculations regarding the elastic, excitation, ionization, and charge transfer cross sections in collisions among relevant ions, neutrals, and isotopes in the low-to intermediate-energy regime. We summarize here some of our recent work. (author)

  8. Complex workplace radiation fields at European high-energy accelerators and thermonuclear fusion facilities

    CERN Document Server

    Bilski, P; D'Errico, F; Esposito, A; Fehrenbacher, G; Fernàndez, F; Fuchs, A; Golnik, N; Lacoste, V; Leuschner, A; Sandri, S; Silari, M; Spurny, F; Wiegel, B; Wright, P

    2006-01-01

    This report outlines the research needs and research activities within Europe to develop new and improved methods and techniques for the characterization of complex radiation fields at workplaces around high-energy accelerators and the next generation of thermonuclear fusion facilities under the auspices of the COordinated Network for RAdiation Dosimetry (CONRAD) project funded by the European Commission.

  9. Fusion burn equilibria sensitive to the ratio between energy and helium transport

    Science.gov (United States)

    Jakobs, Merlijn; Lopes Cardozo, Niek; Jaspers, Roger

    2014-12-01

    An analysis of the burn equilibria of fusion reactors of the tokamak family is presented. The global (zero-dimensional) analysis is self-consistent in that it takes into account the dependence of the energy confinement on the variables of the burning plasma, such as temperature and density. Universal burn contours are presented for a selection of commonly used scaling laws for energy confinement. It is shown that the output power of a fusion reactor is to good approximation inversely proportional to the particle confinement time, due to the choking effect of the accumulation of helium, the ash of the fusion reaction. It is further shown that, whereas a fusion reactor requires a minimum energy confinement time to ignite, the output power reaches a maximum for an energy confinement that lies about 30% above this minimum. Further improvement of confinement will lower the output, although in some cases the β limit will be the limiting factor. Given that for maximum performance density the confinement and fuel mix are best chosen to be optimal, the particle confinement is proposed as an attractive parameter for burn control.

  10. Theory and modeling of radiation effects in materials for fusion energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Heinisch, H.L.

    1996-04-01

    The U.S./Japan Workshop on Theory and Modeling of Radiation Effects in Materials for Fusion Energy Systems, under Phase III of the DOE/Monbusho collaboration, convened on July 17-18, 1995, at Lawrence Livermore National Laboratory. A brief summary of the workshop is followed by the workshop program.

  11. Historical evolution of nuclear energy systems development and related activities in JAERI. Fission, fusion, accelerator utilization

    Energy Technology Data Exchange (ETDEWEB)

    Tone, Tatsuzo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-03-01

    Overview of the historical evolution of nuclear energy systems development and related activities in JAERI is given in the report. This report reviews the research and development for light water reactor, fast breeder reactor, high temperature gas reactor, fusion reactor and utilization of accelerator-based neutron source. (author)

  12. Recombinant chymosin used for exact and complete removal of a prochymosin derived fusion tag releasing intact native target protein

    DEFF Research Database (Denmark)

    Justesen, Sune; Lamberth, Kasper; Nielsen, Lise-Lotte B

    2009-01-01

    Fusion tags add desirable properties to recombinant proteins, but they are not necessarily acceptable in the final products. Ideally, fusion tags should be removed releasing the intact native protein with no trace of the tag. Unique endoproteinases with the ability to cleave outside their own...... characteristics for the exact removal of fusion tags. It is readily available in highly purified recombinant versions approved by the FDA for preparation of food for human consumption. We suggest that one should consider extending the use of chymosin to the preparation of pharmaceutical proteins....... recognition sequence can potentially cleave at the boundary of any native protein. Chymosin was recently shown to cleave a pro-chymosin derived fusion tag releasing native target proteins. In our hands, however, not all proteins are chymosin-resistant under the acidic cleavage conditions (pH 4.5) used...

  13. Research on Key Technologies of Network Centric System Distributed Target Track Fusion

    Directory of Open Access Journals (Sweden)

    Yi Mao

    2017-01-01

    Full Text Available To realize common tactical picture in network-centered system, this paper proposes a layered architecture for distributed information processing and a method for distributed track fusion on the basis of analyzing the characteristics of network-centered systems. Basing on the noncorrelation of three-dimensional measurement of surveillance and reconnaissance sensors under polar coordinates, it also puts forward an algorithm for evaluating track quality (TQ using statistical decision theory. According to simulation results, the TQ value is associated with the measurement accuracy of sensors and the motion state of targets, which is well matched with the convergence process of tracking filters. Besides, the proposed algorithm has good reliability and timeliness in track quality evaluation.

  14. Targets culture wastes energy on wrong things.

    Science.gov (United States)

    Fyffe, Theresa

    2016-09-14

    Healthcare targets have been in the news a lot - and not in ways that offer comfortable reading. Missed emergency department waiting-time targets and patients waiting longer for treatments have made headlines.

  15. Fast-ignition heavy-ion fusion target by jet impact

    Energy Technology Data Exchange (ETDEWEB)

    Velarde, P. [Instituto de Fusion Nuclear, Universidad Politecnica de Madrid, C/ Jose Gutierrez Abascal, 2. 28006 Madrid (Spain)]. E-mail: pedro@din.upm.es; Ogando, F. [Instituto de Fusion Nuclear, Universidad Politecnica de Madrid, C/ Jose Gutierrez Abascal, 2. 28006 Madrid (Spain); Universidad Nacional de Educacion a Distancia (Spain); Eliezer, S. [Soreq Nuclear Research Center (Israel); Martinez-Val, J.M. [Soreq Nuclear Research Center (Israel)

    2005-05-21

    A new target design for HIF, based on the fast-ignition principles, is proposed. Unlike the previous designs proposed so far, in this case just one energy source is needed to drive the whole process to ignition. The ultra-fast deposition of energy onto the compressed core is produced in this case by hypervelocity jets generated during the process. The collision of jets converts their kinetic energy into thermal energy of the nuclear fuel, which is expected to produce ignition under proper design. The process is studied in this paper, describing its most relevant features like jet production and later collision.

  16. Some Simple Arguments about Cost Externalization and its Relevance to the Price of Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Budny, R.; Winfree, R.

    1999-09-27

    The primary goal of fusion energy research is to develop a source of energy that is less harmful to the environment than are the present sources. A concern often expressed by critics of fusion research is that fusion energy will never be economically competitive with fossil fuels, which in 1997 provided 75% of the world's energy. And in fact, studies of projected fusion electricity generation generally project fusion costs to be higher than those of conventional methods. Yet it is widely agreed that the environmental costs of fossil fuel use are high. Because these costs aren't included in the market price, and furthermore because many governments subsidize fossil fuel production, fossil fuels seem less expensive than they really are. Here we review some simple arguments about cost externalization which provide a useful background for discussion of energy prices. The collectively self-destructive behavior that is the root of many environmental problems, including fossil fuel use, was termed ''the tragedy of the commons'' by the biologist G. Hardin. Hardin's metaphor is that of a grazing commons that is open to all. Each herdsman, in deciding whether to add a cow to his herd, compares the benefit of doing so, which accrues to him alone, to the cost, which is shared by all the herdsmen using the commons, and therefore adds his cow. In this way individually rational behavior leads to the collective destruction of the shared resource. As Hardin pointed out, pollution is one kind of tragedy of the commons. CO{sub 2} emissions and global warming are in this sense classic tragedies.

  17. The NIF: An international high energy density science and inertial fusion user facility

    Directory of Open Access Journals (Sweden)

    Moses E.I.

    2013-11-01

    Full Text Available The National Ignition Facility (NIF, a 1.8-MJ/500-TW Nd:Glass laser facility designed to study inertial confinement fusion (ICF and high-energy-density science (HEDS, is operational at Lawrence Livermore National Laboratory (LLNL. A primary goal of NIF is to create the conditions necessary to demonstrate laboratory-scale thermonuclear ignition and burn. NIF experiments in support of indirect-drive ignition began late in FY2009 as part of the National Ignition Campaign (NIC, an international effort to achieve fusion ignition in the laboratory. To date, all of the capabilities to conduct implosion experiments are in place with the goal of demonstrating ignition and developing a predictable fusion experimental platform in 2012. The results from experiments completed are encouraging for the near-term achievement of ignition. Capsule implosion experiments at energies up to 1.6 MJ have demonstrated laser energetics, radiation temperatures, and symmetry control that scale to ignition conditions. Of particular importance is the demonstration of peak hohlraum temperatures near 300 eV with overall backscatter less than 15%. Important national security and basic science experiments have also been conducted on NIF. Successful demonstration of ignition and net energy gain on NIF will be a major step towards demonstrating the feasibility of laser-driven Inertial Fusion Energy (IFE. This paper will describe the results achieved so far on the path toward ignition, the beginning of fundamental science experiments and the plans to transition NIF to an international user facility providing access to HEDS and fusion energy researchers around the world.

  18. Analysis of the role of neutron transfer in asymmetric fusion reactions at subbarrier energies

    Energy Technology Data Exchange (ETDEWEB)

    Ogloblin, A. A. [National Research Center Kurchatov Institute (Russian Federation); Zhang, H. Q.; Lin, C. J.; Jia, H. M. [China Institute of Atomic Energy (China); Khlebnikov, S. V. [Khlopin Radium Institute (Russian Federation); Kuzmin, E. A.; Danilov, A. N.; Demyanova, A. S. [National Research Center Kurchatov Institute (Russian Federation); Trzaska, W. H. [University of Jyväskylä, Department of Physics (Finland); Xu, X. X. [China Institute of Atomic Energy (China); Yang, F. [National Research Center Kurchatov Institute (Russian Federation); Sargsyan, V. V., E-mail: sargsyan@theor.jinr.ru; Adamian, G. G.; Antonenko, N. V. [Joint Institute for Nuclear Research (Russian Federation); Scheid, W. [Institüt für Theoretische Physik der Justus-Liebig-Universität (Germany)

    2015-12-15

    The excitation functions were measured for the {sup 28}Si + {sup 208}Pb complete-fusion (capture) reaction at deep subbarrier energies. The results were compared with the cross sections predicted within the quantum diffusion approach. The role of neutron transfer in the case of positive Q values in the {sup 28}Si + {sup 124}Sn, {sup 208}Pb; {sup 30}Si + {sup 124}Sn, {sup 208}Pb; {sup 20}Ne + {sup 208}Pb; {sup 40}Ca + {sup 96}Zr; and {sup 134}Te + {sup 40}Ca complete-fusion (capture) reactions is discussed.

  19. Fusion energy in an inertial electrostatic confinement device using a magnetically shielded grid

    Energy Technology Data Exchange (ETDEWEB)

    Hedditch, John, E-mail: john.hedditch@sydney.edu.au; Bowden-Reid, Richard, E-mail: rbow3948@physics.usyd.edu.au; Khachan, Joe, E-mail: joe.khachan@sydney.edu.au [School of Physics, The University of Sydney, Sydney, New South Whales 2006 (Australia)

    2015-10-15

    Theory for a gridded inertial electrostatic confinement (IEC) fusion system is presented, which shows a net energy gain is possible if the grid is magnetically shielded from ion impact. A simplified grid geometry is studied, consisting of two negatively biased coaxial current-carrying rings, oriented such that their opposing magnetic fields produce a spindle cusp. Our analysis indicates that better than break-even performance is possible even in a deuterium-deuterium system at bench-top scales. The proposed device has the unusual property that it can avoid both the cusp losses of traditional magnetic fusion systems and the grid losses of traditional IEC configurations.

  20. Comparative evaluation of solar, fission, fusion, and fossil energy resources. Part 5: Conclusions and recomendations

    Science.gov (United States)

    Williams, J. R.

    1974-01-01

    Air pollution resulting from the use of fossil fuels is discussed. Phenomena relating to the emission of CO2 such as the greenhouse effect and multiplier effect are explored. Particulate release is also discussed. The following recommendations are made for the elimination of fossil fuel combustion products in the United States: development of nuclear breeder reactors, use of solar energy systems, exploration of energy alternatives such as geothermal and fusion, and the substitution of coal for gas and oil use.

  1. Progress Towards the Development of a Traveling Wave Direct Energy Converter for Aneutronic Fusion Propulsion Applications

    Science.gov (United States)

    Tarditi, A. G.; Chap, A.; Wolinsky, J.; Scott, J. H.

    2015-01-01

    A coordinated experimental and theory/simulation effort has been carried out to investigate the physics of the Traveling Wave Direct Energy Converter (TWDEC), a scheme that has been proposed in the past for the direct conversion into electricity of the kinetic energy of an ion beam generated from fusion reactions. This effort has been focused in particular on the TWDEC process in the high density beam regime, thus accounting for the ion beam expansion due to its space charge.

  2. High energy resolution characteristics on 14MeV neutron spectrometer for fusion experimental reactor

    Energy Technology Data Exchange (ETDEWEB)

    Iguchi, Tetsuo [Tokyo Univ., Tokai, Ibaraki (Japan). Nuclear Engineering Research Lab.; Takada, Eiji; Nakazawa, Masaharu

    1996-10-01

    A 14MeV neutron spectrometer suitable for an ITER-like fusion experimental reactor is now under development on the basis of a recoil proton counter telescope principle in oblique scattering geometry. To verify its high energy resolution characteristics, preliminary experiments are made for a prototypical detector system. The comparison results show reasonably good agreement and demonstrate the possibility of energy resolution of 2.5% in full width at half maximum for 14MeV neutron spectrometry. (author)

  3. An approach to optimal hyperspectral and multispectral signature and image fusion for detecting hidden targets on shorelines

    Science.gov (United States)

    Bostater, Charles R.

    2015-10-01

    Hyperspectral and multispectral imagery of shorelines collected from airborne and shipborne platforms are used following pushbroom imagery corrections using inertial motion motions units and augmented global positioning data and Kalman filtering. Corrected radiance or reflectance images are then used to optimize synthetic high spatial resolution spectral signatures resulting from an optimized data fusion process. The process demonstrated utilizes littoral zone features from imagery acquired in the Gulf of Mexico region. Shoreline imagery along the Banana River, Florida, is presented that utilizes a technique that makes use of numerically embedded targets in both higher spatial resolution multispectral images and lower spatial resolution hyperspectral imagery. The fusion process developed utilizes optimization procedures that include random selection of regions and pixels in the imagery, and minimizing the difference between the synthetic signatures and observed signatures. The optimized data fusion approach allows detection of spectral anomalies in the resolution enhanced data cubes. Spectral-spatial anomaly detection is demonstrated using numerically embedded line targets within actual imagery. The approach allows one to test spectral signature anomaly detection and to identify features and targets. The optimized data fusion techniques and software allows one to perform sensitivity analysis and optimization in the singular value decomposition model building process and the 2-D Butterworth cutoff frequency and order numerical selection process. The data fusion "synthetic imagery" forms a basis for spectral-spatial resolution enhancement for optimal band selection and remote sensing algorithm development within "spectral anomaly areas". Sensitivity analysis demonstrates the data fusion methodology is most sensitive to (a) the pixels and features used in the SVD model building process and (b) the 2-D Butterworth cutoff frequency optimized by application of K

  4. Progress in Inertial Fusion Energy Modelling at DENIM

    Energy Technology Data Exchange (ETDEWEB)

    Velarde, G; Cabellos, O; Caturla, M J; Florido, R; Gil, J M; Leon, P T; Mancini, R; Marian, J; Martel, P; Martinez-Val, J M; Minguez, E; Mota, F; Ogando, F; Perlado, J M; Piera, M; Reyes, S; Rodriguez, R; Rubiano, J G; Salvador, M; Sanz, J; Sauvan, P; Velarde, M; Velarde, P

    2004-11-17

    New results of the jet driven ignition target are presented, both with direct and indirect drive. This target is based on the conical guided target used in fast ignition, but use only one laser pulse. The ignition of the target is started by the impact of a jet produced in the guiding cone, instead of using charged particles generated by a other high power laser. We have shown that a laser or X-ray pulse could be used to produce a high velocity jet of several hundred of km/s by an accumulative effect, and we use these ideas to design this new kind of targets. In order to increase the efficiency of the process, we scan in the simulations different materials, cone profiles and laser intensities. ANALOP is a code developed to calculate opacities for hot plasmas, using analytical potentials including density and temperature effects. It has been recently updated to include the radiative transport into the rate equations by mean of the escape factors, and in parallel a line transport code which solve self-consistently the rate equation and radiative transfer equation in 1D planar geometry has been also developed. We have developed a comprehensive methodology to compute uncertainties on activation calculations. First we developed a sensitivity-uncertainty analysis method, providing the uncertainties of the different inventory responses functions due to the uncertainty of each of the reaction cross sections separately. Lately, we have developed and proved the excellent behaviour of a Monte Carlo-based methodology in assessing the synergetic/global effect of the complete set of cross-sections uncertainties on calculated radiological quantities. The methods have been applied to the activation analysis of the National Ignition Facility (NIF) and different IFE concepts (HYLIFE and Sombrero). Research on multiscale modeling of radiation damage in metals will be presented in comparison with ''ad hoc'' experiments. Research on SiC composite is being pursued at

  5. Energy-Resources - the Safety of Fusion-Reactors

    NARCIS (Netherlands)

    Ornstein, L. T. M.

    1994-01-01

    In part I the world's present energy production and consumption will be treated, as well as the expected increase in demand in the next decades. The limited availability of fossil fuels, the impact on the environment caused by the burning of these fuels, the restricted applicability of renewabl

  6. Energy-Resources - the Safety of Fusion-Reactors

    NARCIS (Netherlands)

    Ornstein, L. T. M.

    1994-01-01

    In part I the world's present energy production and consumption will be treated, as well as the expected increase in demand in the next decades. The limited availability of fossil fuels, the impact on the environment caused by the burning of these fuels, the restricted applicability of renewabl

  7. Adaptive polarization image fusion based on regional energy dynamic weighted average

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yong-qiang; PAN Quan; ZHANG Hong-cai

    2005-01-01

    According to the principle of polarization imaging and the relation between Stokes parameters and the degree of linear polarization, there are much redundant and complementary information in polarized images. Since man-made objects and natural objects can be easily distinguished in images of degree of linear polarization and images of Stokes parameters contain rich detailed information of the scene, the clutters in the images can be removed efficiently while the detailed information can be maintained by combining these images. An algorithm of adaptive polarization image fusion based on regional energy dynamic weighted average is proposed in this paper to combine these images. Through an experiment and simulations,most clutters are removed by this algorithm. The fusion method is used for different light conditions in simulation, and the influence of lighting conditions on the fusion results is analyzed.

  8. Machine Learning and Sensor Fusion for Estimating Continuous Energy Expenditure

    OpenAIRE

    Vyas, Nisarg; BodyMedia, Inc.; Farringdon, Jonathan; BodyMedia Inc.; Andre, David; Cerebellum Capital, Inc.; Stivoric, John Ivo; BodyMedia

    2012-01-01

    In this article we provide insight into the BodyMedia FIT armband system — a wearable multi-sensor technology that continuously monitors physiological events related to energy expenditure for weight management using machine learning and data modeling methods. Since becoming commercially available in 2001, more than half a million users have used the system to track their physiological parameters and to achieve their individual health goals including weight-loss. We describe several challenges...

  9. Bearing fault identification by higher order energy operator fusion: A non-resonance based approach

    Science.gov (United States)

    Faghidi, H.; Liang, M.

    2016-10-01

    We report a non-resonance based approach to bearing fault detection. This is achieved by a higher order energy operator fusion (HOEO_F) method. In this method, multiple higher order energy operators are fused to form a single simple transform to process the bearing signal obscured by noise and vibration interferences. The fusion is guided by entropy minimization. Unlike the popular high frequency resonance technique, this method does not require the information of resonance excited by the bearing fault. The effects of the HOEO_F method on signal-to-noise ratio (SNR) and signal-to-interference ratio (SIR) are illustrated in this paper. The performance of the proposed method in handling noise and interferences has been examined using both simulated and experimental data. The results indicate that the HOEO_F method outperforms both the envelope method and the original energy operator method.

  10. The Fukushima nuclear disaster and its effects on media framing of fission and fusion energy technologies

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Luisa; Horta, Ana; Pereira, Sergio; Delicado, Ana [Institute of Social Sciences of the University of Lisbon, Av. Prof. Anibal de Bettencourt, 9 1600-189 Lisbon (Portugal)

    2015-07-01

    This paper presents results of a comparison of media coverage of fusion and fission energy technologies in three countries (Germany, Spain and Portugal) and in the English language international print media addressing transnational elite, from 2008 to 2012. The analysis showed that the accident in Fukushima in March 2010 did not have significant impact on media framing of nuclear fusion in the major part of print media under investigation. In fact, fusion is clearly dissociated from traditional nuclear (fission) energy and from nuclear accidents. It tends to be portrayed as a safe, clean and unlimited source of energy, although less credited when confronted with research costs, technological feasibility and the possibility to be achieved in a reasonable period of time. On the contrary, fission is portrayed as a hazardous source of energy, expensive when compared to research costs of renewables, hardly a long-term energy option, susceptible to contribute to the proliferation of nuclear weapons or rogue military use. Fukushima accident was consistently discussed in the context of safety problems of nuclear power plants and in many cases appeared not as an isolated event but rather as a reminder of previous nuclear disasters such as Three Miles Island and Chernobyl. (authors)

  11. Miniature proportional counter for compression measurements of laser-fusion targets

    Energy Technology Data Exchange (ETDEWEB)

    Lane, S.M.; Dellis, J.H.; Bennett, C.K.; Campbell, E.M.

    1981-10-01

    Direct drive laser fusion targets consisting of DT gas encapsulated in glass microshells produce 14.1 MeV neutrons that can interact with silicon-28 nuclei in the glass to produce a 2.2 minute aluminum-28 activity. From the number of /sup 28/Al nuclei created and the neutron yield, the compressed glass areal density can be found. To determine the number of activated atoms created, we collect approximately one-half of the target debris on a thin metal foil which is transferred to our beta-gamma coincidence detector. This detector consists of a 25 cm x 25 cm NaI(Tl) crystal having a 5 cm x 15 cm well. We have recently built a miniature proportional counter that fits into this well and is used to detect beta particles. It is constructed of .025 cm thick copper and has nine separate chambers through which methane flows. The coincidence background is 0.14 cpm and the measured beta efficiency is 45%. We are now building a .0125 cm thick counter made of aluminum having a predicted efficiency of > 90%.

  12. Research on the image fusion and target extraction based on bionic compound eye system

    Science.gov (United States)

    Zhang, Shaowei; Hao, Qun; Song, Yong; Wang, Zihan; Zhang, Kaiyu; Zhang, Shiyu

    2015-08-01

    People attach more and more importance to bionic compound eye due to its advantages such as small volume, large field of view and sensitivity to high-speed moving objects. Small field of view and large volume are the disadvantages of traditional image sensor and in order to avoid these defects, this paper intends to build a set of compound eye system based on insect compound eye structure and visual processing mechanism. In the center of this system is the primary sensor which has high resolution ratio. The primary sensor is surrounded by the other six sensors which have low resolution ratio. Based on this system, this paper will study the target image fusion and extraction method by using plane compound eye structure. This paper designs a control module which can combine the distinguishing features of high resolution image with local features of low resolution image so as to conduct target detection, recognition and location. Compared with traditional ways, the way of high resolution in the center and low resolution around makes this system own the advantages of high resolution and large field of view and enables the system to detect the object quickly and recognize the object accurately.

  13. Laser targets and experiments for the sake of science and energy in the 22nd century

    Indian Academy of Sciences (India)

    N G Borisenko; Yu A Merkuliev

    2010-12-01

    Laser fusion for energy and hybride schemes with laser application are original and highly tempting because they are ecofriendly, with almost unlimited resources. Though quite challenging, even development stage is fruitful in hi-tech and provides vast fundamental knowledge. The present paper discusses important results concerning target fabrication detailing several finer points of view which may not appear obvious. The current status of and achievements in targets are provided and validation experiments are discussed. The prospects and the unexpected difficulties are presented. The comparable resources and cost (unlike sizes differing orders of magnitude) for the targets and for driver over the driver’s life cycle scale prove there is no time to waste with target technology findings and validation experiments, especially in view of ignition shortly expected with National Ignition Facility.

  14. HYPERFUSE: a hypervelocity inertial confinement system for fusion energy production and fission waste transmutation

    Energy Technology Data Exchange (ETDEWEB)

    Makowitz, H.; Powell, J.R.; Wiswall, R.

    1980-01-01

    Parametric system studies of an inertial confinement fusion (ICF) reactor system to transmute fission products from a LWR economy have been carried out. The ICF reactors would produce net power in addition to transmuting fission products. The particular ICF concept examined is an impact fusion approach termed HYPERFUSE, in which hypervelocity pellets, traveling on the order of 100 to 300 km/sec, collide with each other or a target block in a reactor chamber and initiate a thermonuclear reaction. The DT fusion fuel is contained in a shell of the material to be transmuted, e.g., /sup 137/Cs, /sup 90/Sr, /sup 129/I, /sup 99/Tc, etc. The 14-MeV fusion neutrons released during the pellet burn cause transmutation reactions (e.g., (n,2n), (n,..cap alpha..), (n,..gamma..), etc.) that convert the long-lived fission products (FP's) either to stable products or to species that decay with a short half-life to a stable product. The transmutation parametric studies conclude that the design of the hypervelocity projectiles should emphasize the achievement of high densities in the transmutation regions (greater than the DT fusion fuel density), as well as the DT ignition and burn criterion (rho R = 1.0 to 3.0) requirements. These studies also indicate that masses on the order of 1.0 g at densities of rho greater than or equal to 500.0 g/cm/sup 3/ are required for a practical fusion-based fission product transmutation system.

  15. On_the_implementation_of_the_conditions_of_Inertial_Confinement_ Fusion by bombarding the target a macro particle

    CERN Document Server

    Dolya, S N

    2013-01-01

    The acceleration of lithium tube segments with the length one centimeter, diameter sixteen microns wall thickness one nanometer is considered. These segments are electrically charged by proton beams produced by an electron beam source. Then, they are accelerated by the traveling wave field in a spiral waveguide. The segments are next sent to a target where they are compressed by three hundred times in the longitudinal direction and compressing target radially, so the conditions for thermonuclear fusion are realized.

  16. Sensitivity of the fusion cross section to the density dependence of the symmetry energy

    CERN Document Server

    Reinhard, P -G; Stevenson, P D; Piekarewicz, J; Oberacker, V E; Maruhn, J A

    2016-01-01

    It is the aim of this paper to discuss the impact of nuclear fusion on the EOS. This is a timely subject given the expected availability of increasingly exotic beams at rare isotope facilities\\,\\cite{balantekin2014}. In practice, we focus on $^{48}$Ca+$^{48}$Ca fusion. We employ three different approaches to calculate fusion cross-sections for a set of energy density functionals with systematically varying nuclear matter properties. Fusion calculations are performed using frozen densities, using a dynamic microscopic method based on density-constrained time-dependent Hartree-Fock (DC-TDHF) approach, as well as direct TDHF study of above barrier cross-sections. For these studies, we employ a family of Skyrme parametrizations with systematically varied nuclear matter properties. We find a slight preference for forces which deliver a slope of symmetry energy of $L\\approx 50$\\,MeV that corresponds to a neutron-skin thickness of $^{48}$Ca of $R_\\mathrm{skin}\\!=\\!(0.180\\!-\\!0.210)$\\,fm.

  17. Study on fission blanket fuel cycling of a fusion-fission hybrid energy generation system

    Science.gov (United States)

    Zhou, Z.; Yang, Y.; Xu, H.

    2011-10-01

    This paper presents a preliminary study on neutron physics characteristics of a light water cooled fission blanket for a new type subcritical fusion-fission hybrid reactor aiming at electric power generation with low technical limits of fission fuel. The major objective is to study the fission fuel cycling performance in the blanket, which may possess significant impacts on the feasibility of the new concept of fusion-fission hybrid reactor with a high energy gain (M) and tritium breeding ratio (TBR). The COUPLE2 code developed by the Institute of Nuclear and New Energy Technology of Tsinghua University is employed to simulate the neutronic behaviour in the blanket. COUPLE2 combines the particle transport code MCNPX with the fuel depletion code ORIGEN2. The code calculation results show that soft neutron spectrum can yield M > 20 while maintaining TBR >1.15 and the conversion ratio of fissile materials CR > 1 in a reasonably long refuelling cycle (>five years). The preliminary results also indicate that it is rather promising to design a high-performance light water cooled fission blanket of fusion-fission hybrid reactor for electric power generation by directly loading natural or depleted uranium if an ITER-scale tokamak fusion neutron source is achievable.

  18. Ion Fast Ignition-Establishing a Scientific Basis for Inertial Fusion Energy --- Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, Richard Burnite [General Atomics; Foord, Mark N. [Lawrence Livermore National Laboratory; Wei, Mingsheng [General Atomics; Beg, Farhat N. [University of California, San Diego; Schumacher, Douglass W. [The Ohio State University

    2013-10-31

    The Fast Ignition (FI) Concept for Inertial Confinement Fusion (ICF) has the potential to provide a significant advance in the technical attractiveness of Inertial Fusion Energy reactors. FI differs from conventional ?central hot spot? (CHS) target ignition by decoupling compression from heating: using a laser (or heavy ion beam or Z pinch) drive pulse (10?s of nanoseconds) to create a dense fuel and a second, much shorter (~10 picoseconds) high intensity pulse to ignite a small volume within the dense fuel. The compressed fuel is opaque to laser light. The ignition laser energy must be converted to a jet of energetic charged particles to deposit energy in the dense fuel. The original concept called for a spray of laser-generated hot electrons to deliver the energy; lack of ability to focus the electrons put great weight on minimizing the electron path. An alternative concept, proton-ignited FI, used those electrons as intermediaries to create a jet of protons that could be focused to the ignition spot from a more convenient distance. Our program focused on the generation and directing of the proton jet, and its transport toward the fuel, none of which were well understood at the onset of our program. We have developed new experimental platforms, diagnostic packages, computer modeling analyses, and taken advantage of the increasing energy available at laser facilities to create a self-consistent understanding of the fundamental physics underlying these issues. Our strategy was to examine the new physics emerging as we added the complexity necessary to use proton beams in an inertial fusion energy (IFE) application. From the starting point of a proton beam accelerated from a flat, isolated foil, we 1) curved it to focus the beam, 2) attached the foil to a superstructure, 3) added a side sheath to protect it from the surrounding plasma, and finally 4) studied the proton beam behavior as it passed through a protective end cap into plasma. We built up, as we proceeded

  19. Ion Fast Ignition-Establishing a Scientific Basis for Inertial Fusion Energy --- Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, Richard Burnite [General Atomics; Foord, Mark N. [Lawrence Livermore National Laboratory; Wei, Mingsheng [General Atomics; Beg, Farhat N. [University of California, San Diego; Schumacher, Douglass W. [The Ohio State University

    2013-10-31

    The Fast Ignition (FI) Concept for Inertial Confinement Fusion (ICF) has the potential to provide a significant advance in the technical attractiveness of Inertial Fusion Energy reactors. FI differs from conventional ?central hot spot? (CHS) target ignition by decoupling compression from heating: using a laser (or heavy ion beam or Z pinch) drive pulse (10?s of nanoseconds) to create a dense fuel and a second, much shorter (~10 picoseconds) high intensity pulse to ignite a small volume within the dense fuel. The compressed fuel is opaque to laser light. The ignition laser energy must be converted to a jet of energetic charged particles to deposit energy in the dense fuel. The original concept called for a spray of laser-generated hot electrons to deliver the energy; lack of ability to focus the electrons put great weight on minimizing the electron path. An alternative concept, proton-ignited FI, used those electrons as intermediaries to create a jet of protons that could be focused to the ignition spot from a more convenient distance. Our program focused on the generation and directing of the proton jet, and its transport toward the fuel, none of which were well understood at the onset of our program. We have developed new experimental platforms, diagnostic packages, computer modeling analyses, and taken advantage of the increasing energy available at laser facilities to create a self-consistent understanding of the fundamental physics underlying these issues. Our strategy was to examine the new physics emerging as we added the complexity necessary to use proton beams in an inertial fusion energy (IFE) application. From the starting point of a proton beam accelerated from a flat, isolated foil, we 1) curved it to focus the beam, 2) attached the foil to a superstructure, 3) added a side sheath to protect it from the surrounding plasma, and finally 4) studied the proton beam behavior as it passed through a protective end cap into plasma. We built up, as we proceeded

  20. Targeting Net Zero Energy for Military Installations (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Burman, K.

    2012-05-01

    Targeting Net Zero Energy for Military Installations in Kaneohe Bay, Hawaii. A net zero energy installation (NZEI) is one that produces as much energy from on-site renewable sources as it consumes. NZEI assessment provides a systematic approach to energy projects.

  1. Targeting the unfolded protein response in glioblastoma cells with the fusion protein EGF-SubA.

    Directory of Open Access Journals (Sweden)

    Antony Prabhu

    Full Text Available Rapidly growing tumors require efficient means to allow them to adapt to fluctuating microenvironments consisting of hypoxia, nutrient deprivation, and acidosis. The unfolded protein response (UPR represents a defense mechanism allowing cells to respond to these adverse conditions. The chaperone protein GRP78 serves as a master UPR regulator that is aberrantly expressed in a variety of cancers, including glioma. Therefore, cancer cells may be particularly reliant upon the adaptive mechanisms offered by the UPR and targeting GRP78 may represent a unique therapeutic strategy. Here we report that diffuse expression of GRP78 protein is present in Grade III-IV, but not Grade I-II glioma. To determine the role GRP78 plays in glioblastoma tumorigenesis, we explored the anti-tumor activity of the novel fusion protein EGF-SubA, which combines EGF with the cytotoxin SubA that has been recently shown to selectively cleave GRP78. EGF-SubA demonstrated potent tumor-specific proteolytic activity and cytotoxicity in glioblastoma lines and potentiated the anti-tumor activity of both temozolomide and ionizing radiation. To determine if the tumor microenvironment influences EGF-SubA activity, we maintained cells in acidic conditions that led to both UPR activation and increased EGF-SubA induced cytotoxicity. EGF-SubA was well tolerated in mice and led to a significant tumor growth delay in a glioma xenograft mouse model. The UPR is emerging as an important adaptive pathway contributing to glioma tumorigenesis. Targeting its primary mediator, the chaperone protein GRP78, through specific, proteolytic cleavage with the immunotoxin EGF-SubA represents a novel and promising multi-targeted approach to cancer therapy.

  2. Energy dependence of fusion evaporation-residue cross sections in the sup 28 Si+ sup 28 Si reaction

    Energy Technology Data Exchange (ETDEWEB)

    Vineyard, M.F.; Bauer, J.S.; Gosdin, C.H.; Trotter, R.S. (Department of Physics, University of Richmond, Richmond, Virginia 23173 (USA)); Kovar, D.G.; Beck, C.; Henderson, D.J.; Janssens, R.V.F.; Wilkins, B.D.; Rosner, G.; Chowdhury, P.; Ikezoe, H.; Kuhn, W. (Physics Division, Argonne National Laboratory, Argonne, Illinois 60439 (USA)); Kolata, J.J.; Hinnefeld, J.D. (Department of Physics, University of Notre Dame, Notre Dame, Indiana 46556 (USA)); Maguire, C.F. (Department of Physics Astronomy, Vanderbilt University, Nashville, Tennessee 37235 (USA)); Mateja, J.F. (Division of Educational Programs, Argonne National Laboratory, Argonne, Illinois 60439 (USA)); Prosser, F.W. (Department of Physics, University of Kansas, Lawrence, Kansas 66045 (USA)); Stephans, G.S.F. (Laboratory for Nuclear Science, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (USA))

    1990-03-01

    Velocity distributions of mass-identified evaporation residues produced in the {sup 28}Si+{sup 28}Si reaction have been measured at bombarding energies of 174, 215, 240, 309, 397, and 452 MeV using time-of-flight techniques. These distributions were used to identify evaporation residues and to separate the complete-fusion and incomplete-fusion components. Angular distributions and total cross sections were extracted at all six bombarding energies. The complete-fusion evaporation-residue cross sections and the deduced critical angular momenta are compared with lower energy data and the predictions of existing models.

  3. The Mercury Project: A High Average Power, Gas-Cooled Laser For Inertial Fusion Energy Development

    Energy Technology Data Exchange (ETDEWEB)

    Bayramian, A; Armstrong, P; Ault, E; Beach, R; Bibeau, C; Caird, J; Campbell, R; Chai, B; Dawson, J; Ebbers, C; Erlandson, A; Fei, Y; Freitas, B; Kent, R; Liao, Z; Ladran, T; Menapace, J; Molander, B; Payne, S; Peterson, N; Randles, M; Schaffers, K; Sutton, S; Tassano, J; Telford, S; Utterback, E

    2006-11-03

    Hundred-joule, kilowatt-class lasers based on diode-pumped solid-state technologies, are being developed worldwide for laser-plasma interactions and as prototypes for fusion energy drivers. The goal of the Mercury Laser Project is to develop key technologies within an architectural framework that demonstrates basic building blocks for scaling to larger multi-kilojoule systems for inertial fusion energy (IFE) applications. Mercury has requirements that include: scalability to IFE beamlines, 10 Hz repetition rate, high efficiency, and 10{sup 9} shot reliability. The Mercury laser has operated continuously for several hours at 55 J and 10 Hz with fourteen 4 x 6 cm{sup 2} ytterbium doped strontium fluoroapatite (Yb:S-FAP) amplifier slabs pumped by eight 100 kW diode arrays. The 1047 nm fundamental wavelength was converted to 523 nm at 160 W average power with 73% conversion efficiency using yttrium calcium oxy-borate (YCOB).

  4. Development of whole energy absorption spectrometer for decay heat measurement on fusion reactor materials

    Energy Technology Data Exchange (ETDEWEB)

    Maekawa, Fujio; Ikeda, Yujiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-03-01

    To measure decay heat on fusion reactor materials irradiated by D-T neutrons, a Whole Energy Absorption Spectrometer (WEAS) consisting of a pair of large BGO (bismuth-germanate) scintillators was developed. Feasibility of decay heat measurement with WEAS for various materials and for a wide range of half-lives (seconds - years) was demonstrated by experiments at FNS. Features of WEAS, such as high sensitivity, radioactivity identification, and reasonably low experimental uncertainty of {approx} 10 %, were found. (author)

  5. Homeland security application of the Army Soft Target Exploitation and Fusion (STEF) system

    Science.gov (United States)

    Antony, Richard T.; Karakowski, Joseph A.

    2010-04-01

    A fusion system that accommodates both text-based extracted information along with more conventional sensor-derived input has been developed and demonstrated in a terrorist attack scenario as part of the Empire Challenge (EC) 09 Exercise. Although the fusion system was developed to support Army military analysts, the system, based on a set of foundational fusion principles, has direct applicability to department of homeland security (DHS) & defense, law enforcement, and other applications. Several novel fusion technologies and applications were demonstrated in EC09. One such technology is location normalization that accommodates both fuzzy semantic expressions such as behind Library A, across the street from the market place, as well as traditional spatial representations. Additionally, the fusion system provides a range of fusion products not supported by traditional fusion algorithms. Many of these additional capabilities have direct applicability to DHS. A formal test of the fusion system was performed during the EC09 exercise. The system demonstrated that it was able to (1) automatically form tracks, (2) help analysts visualize behavior of individuals over time, (3) link key individuals based on both explicit message-based information as well as discovered (fusion-derived) implicit relationships, and (4) suggest possible individuals of interest based on their association with High Value Individuals (HVI) and user-defined key locations.

  6. Membrane-transferring regions of gp41 as targets for HIV-1 fusion inhibition and viral neutralization.

    Science.gov (United States)

    Huarte, Nerea; Lorizate, Maier; Pérez-Payá, Enrique; Nieva, José L

    2011-12-01

    The fusogenic function of HIV-1 gp41 transmembrane Env subunit relies on two different kinds of structural elements: i) a collapsible ectodomain structure (the hairpin or six-helix bundle) that opens and closes, and ii) two membrane- transferring regions (MTRs), the fusion peptide (FP) and the membrane-proximal external region (MPER), which ensure coupling of hairpin closure to apposition and fusion of cell and viral membranes. The isolation of naturally produced short peptides and neutralizing IgG-s, that interact with FP and MPER, respectively, and block viral infection, suggests that these conserved regions might represent useful targets for clinical intervention. Furthermore, MTR-derived peptides have been shown to be membrane-active. Here, it is discussed the potential use of these molecules and how the analysis of their membrane activity in vitro could contribute to the development of HIV fusion inhibitors and effective immunogens.

  7. Forthcoming Break-Even Conditions of Tokamak Plasma Performance for Fusion Energy Development

    Science.gov (United States)

    Hiwatari, Ryoji; Okano, Kunihiko; Asaoka, Yoshiyuki; Tokimatsu, Koji; Konishi, Satoshi; Ogawa, Yuichi

    The present study reveals forthcoming break-even conditions of tokamak plasma performance for the fusion energy development. The first condition is the electric break-even condition, which means that the gross electric power generation is equal to the circulating power in a power plant. This is required for fusion energy to be recognized as a suitable candidate for an alternative energy source. As for the plasma performance (normalized beta value ΒN), confinement improvement factor for H-mode HH, the ratio of plasma density to Greenwald density fnGW), the electric break-even condition requires the simultaneous achievement of 1.2 market. By using a long-term world energy scenario, a break-even price for introduction of fusion energy in the year 2050 is estimated to lie between 65 mill/kWh and 135 mill/kWh under the constraint of 550 ppm CO2 concentration in the atmosphere. In the present study, this break-even price is applied to the economic break-even condition. However, because this break-even price is based on the present energy scenario including uncertainties, the economic break-even condition discussed here should not be considered the sufficient condition, but a necessary condition. Under the conditions of Btmax = 16 T, ηe = 40 %, plant availability 60 %, and a radial build with/without CS coil, the economic break-even condition requires ΒN ˜ 5.0 for 65 mill/kWh of lower break-even price case. Finally, the present study reveals that the demonstration of steady-state operation with ΒN ˜ 3.0 in the ITER project leads to the upper region of the break-even price in the present world energy scenario, which implies that it is necessary to improve the plasma performance beyond that of the ITER advanced plasma operation.

  8. CD160Ig fusion protein targets a novel costimulatory pathway and prolongs allograft survival.

    Directory of Open Access Journals (Sweden)

    Francesca D'Addio

    Full Text Available CD160 is a cell surface molecule expressed by most NK cells and approximately 50% of CD8(+ cytotoxic T lymphocytes. Engagement of CD160 by MHC class-I directly triggers a costimulatory signal to TCR-induced proliferation, cytokine production and cytotoxic effector functions. The role of CD160 in alloimmunity is unknown. Using a newly generated CD160 fusion protein (CD160Ig we examined the role of the novel costimulatory molecule CD160 in mediating CD4(+ or CD8(+ T cell driven allograft rejection. CD160Ig inhibits alloreactive CD8(+ T cell proliferation and IFN-γ production in vitro, in particular in the absence of CD28 costimulation. Consequently CD160Ig prolongs fully mismatched cardiac allograft survival in CD4(-/-, CD28(-/- knockout and CTLA4Ig treated WT recipients, but not in WT or CD8(-/- knockout recipients. The prolonged cardiac allograft survival is associated with reduced alloreactive CD8(+ T cell proliferation, effector/memory responses and alloreactive IFN-γ production. Thus, CD160 signaling is particularly important in CD28-independent effector/memory CD8(+ alloreactive T cell activation in vivo and therefore may serve as a novel target for prevention of allograft rejection.

  9. Data fusion for planning target volume and isodose prediction in prostate brachytherapy

    Science.gov (United States)

    Nouranian, Saman; Ramezani, Mahdi; Mahdavi, S. Sara; Spadinger, Ingrid; Morris, William J.; Salcudean, Septimiu E.; Abolmaesumi, Purang

    2015-03-01

    In low-dose prostate brachytherapy treatment, a large number of radioactive seeds is implanted in and adjacent to the prostate gland. Planning of this treatment involves the determination of a Planning Target Volume (PTV), followed by defining the optimal number of seeds, needles and their coordinates for implantation. The two major planning tasks, i.e. PTV determination and seed definition, are associated with inter- and intra-expert variability. Moreover, since these two steps are performed in sequence, the variability is accumulated in the overall treatment plan. In this paper, we introduce a model based on a data fusion technique that enables joint determination of PTV and the minimum Prescribed Isodose (mPD) map. The model captures the correlation between different information modalities consisting of transrectal ultrasound (TRUS) volumes, PTV and isodose contours. We take advantage of joint Independent Component Analysis (jICA) as a linear decomposition technique to obtain a set of joint components that optimally describe such correlation. We perform a component stability analysis to generate a model with stable parameters that predicts the PTV and isodose contours solely based on a new patient TRUS volume. We propose a framework for both modeling and prediction processes and evaluate it on a dataset of 60 brachytherapy treatment records. We show PTV prediction error of 10:02+/-4:5% and the V100 isodose overlap of 97+/-3:55% with respect to the clinical gold standard.

  10. Preliminary results from recent experiments and future roadmap to Shock Ignition of Fusion Targets

    Science.gov (United States)

    Batani, D.; Malka, G.; Schurtz, G.; Ribeyre, X.; Lebel, E.; Giuffrida, L.; Tikhonchuk, V.; Volpe, L.; Patria, A.; Koester, P.; Labate, L.; Gizzi, L. A.; Antonelli, L.; Richetta, M.; Nejdl, J.; Sawicka, M.; Margarone, D.; Krus, M.; Krousky, E.; Skala, J.; Dudzak, R.; Velyhan, A.; Ullshmied, J.; Renner, O.; Smid, M.; Klimo, O.; Atzeni, S.; Marocchino, A.; Schiavi, A.; Spindloe, C.; O'Dell, T.; Vinci, T.; Wolowski, J.; Badziak, J.; Pysarcizck, T.; Rosinski, M.; Kalinowska, Z.; Chodukowski, T.

    2012-11-01

    Shock ignition (SI) is a new approach to Inertial Confinement Fusion (ICF) based on decoupling the compression and ignition phase. The last one relies on launching a strong shock through a high intensity laser spike (<= 1016 W/cm2) at the end of compression. In this paper, first we described an experiment performed using the PALS iodine laser to study laser-target coupling and laser-plasma interaction in an intensity regime relevant for SI. A first beam with wavelength λ = 1.33 μm and low intensity was used to create an extended preformed plasma, and a second one with λ = 0.44 μm to create a strong shock. Several diagnostics characterized the preformed plasma and the interaction of the main pulse. Pressure up to 90 Mbar was inferred. In the last paper of the paper, we discuss the relevant steps, which can be followed in order to approach the demonstration of SI on laser facilities like LMJ.

  11. Numerical study of the irradiation uniformity of a directly driven inertial confinement fusion target

    Science.gov (United States)

    Temporal, M.; Canaud, B.; Laffite, S.; Le Garrec, B. J.; Murakami, M.

    2010-11-01

    In the Inertial Confinement Fusion the uniformity of the irradiation still represents a crucial issue. In this context a spherical capsule directly driven by laser beams have been assessed numerically [1]. Two schemes characterized by 32 and 48 directions of irradiation [2] with associated a single laser beam or a bundle of laser beams [3] characterized by a super-Gaussian intensity profile are considered. Beam imperfections as power imbalance and pointing errors have been taken into account. It is found that the focal spot that minimizes the rms deviation depends on the beam imperfections [4]. The numerical calculations show that the uniformity of the irradiation evolves in time. The results calculated considering the illumination of a spherical target will be compared with those obtained when the irradiation is taken into account. [1] M. Temporal, B. Canaud. Eur. Phys. J. D 55 139 (2009). [2] M. Murakami, N. Sarukura, H. Azechi, M. Temporal, A.J. Schmitt, in press to Phys. Plasmas (July issue, 2010). [3] M. Temporal, B. Canaud, B. J. Le Garrec, Phys. Plasmas 17 022701 (2010). [4] M. Temporal, B. Canaud, S. Laffite, B.J. Le Garrec, M. Murakami. Phys. Plasmas 17 064504 (2010).

  12. The Economics of the Mandatory Renewable Energy Target (MRET)

    OpenAIRE

    del Mundo, Israel; Wills, Ian R.

    2005-01-01

    In response to increasing awareness of climate change, the Howard government implemented the Mandatory Renewable Energy Target (MRET) in 2001. It requires electricity wholesalers to source an additional 9500 GWh of electricity from renewable sources by 2010. Electricity wholesalers are required to subsidise renewable energy generators by purchasing Renewable Energy Certificates (RECs) equivalent to the target; failure to do so incurs a penalty of $40 per megawatt. Economic analysis is used to...

  13. Summary of the report of the Senior Committee on Environmental, Safety, and Economic Aspects of Magnetic Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Holdren, J.P.; Berwald, D.H.; Budnitz, R.J.; Crocker, J.G.; Delene, J.G.; Endicott, R.D.; Kazimi, M.S.; Krakowski, R.A.; Logan, B.G.; Schultz, K.R.

    1987-09-10

    The Senior Committee on Environmental, Safety, and Economic Aspects of Magnetic Fusion Energy (ESECOM) has assessed magnetic fusion energy's prospects for providing energy with economic, environmental, and safety characteristics that would be attractive compared with other energy sources (mainly fission) available in the year 2015 and beyond. ESECOM gives particular attention to the interaction of environmental, safety, and economic characteristics of a variety of magnetic fusion reactors, and compares them with a variety of fission cases. Eight fusion cases, two fusion-fission hybrid cases, and four fission cases are examined, using consistent economic and safety models. These models permit exploration of the environmental, safety, and economic potential of fusion concepts using a wide range of possible materials choices, power densities, power conversion schemes, and fuel cycles. The ESECOM analysis indicates that magnetic fusion energy systems have the potential to achieve costs-of-electricity comparable to those of present and future fission systems, coupled with significant safety and environmental advantages. 75 refs., 2 figs., 24 tabs.

  14. Fusion of Si28+Si28,30: Different trends at sub-barrier energies

    Science.gov (United States)

    Montagnoli, G.; Stefanini, A. M.; Esbensen, H.; Jiang, C. L.; Corradi, L.; Courtin, S.; Fioretto, E.; Grebosz, J.; Haas, F.; Jia, H. M.; Mazzocco, M.; Michelagnoli, C.; Mijatović, T.; Montanari, D.; Parascandolo, C.; Scarlassara, F.; Strano, E.; Szilner, S.; Torresi, D.

    2014-10-01

    Background: The fusion excitation function of the system Si28+Si28 at energies near and below the Coulomb barrier is known only down to ≃15 mb. This precludes any information on both coupling effects on sub-barrier cross sections and the possible appearance of hindrance. For Si28+Si30 even if the fusion cross section is measured down to ≃50 μb, the evidence of hindrance is marginal. Both systems have positive fusion Q values. While Si28 has a deformed oblate shape, Si30 is spherical. Purpose: We investigate 1. the possible influence of the different structure of the two Si isotopes on the fusion excitation functions in the deep sub-barrier region and 2. whether hindrance exists in the Si+Si systems and whether it is strong enough to generate an S-factor maximum, thus allowing a comparison with lighter heavy-ion systems of astrophysical interest. Methods: Si28 beams from the XTU Tandem accelerator of the INFN Laboratori Nazionali di Legnaro were used. The setup was based on an electrostatic beam separator, and fusion evaporation residues (ER) were detected at very forward angles. Angular distributions of ER were measured. Results: Fusion cross sections of Si28+Si28 have been obtained down to ≃600 nb. The slope of the excitation function has a clear irregularity below the barrier, but no indication of a S-factor maximum is found. For Si28+Si30 the previous data have been confirmed and two smaller cross sections have been measured down to ≃4 μb. The trend of the S-factor reinforces the previous weak evidence of hindrance. Conclusions: The sub-barrier cross sections for Si28+Si28 are overestimated by coupled-channels calculations based on a standard Woods-Saxon potential, except for the lowest energies. Calculations using the M3Y+repulsion potential are adjusted to fit the Si28+Si28 and the existing Si30+Si30 data. An additional weak imaginary potential (probably simulating the effect of the oblate Si28 deformation) is required to fit the low-energy trend of

  15. A Sustainable Nuclear Fuel Cycle Based on Laser Inertial Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Moses, E; Diaz de la Rubia, T; Storm, E; Latkowski, J; Farmer, J; Abbott, R; Kramer, K; Peterson, P; Shaw, H; Lehman II, R

    2009-05-22

    The National Ignition Facility (NIF), a laser-based Inertial Confinement Fusion (ICF) experiment designed to achieve thermonuclear fusion ignition and burn in the laboratory, will soon be completed at the Lawrence Livermore National Laboratory. Experiments designed to accomplish the NIF's goal will commence in 2010, using laser energies of 1 to 1.3 MJ. Fusion yields of the order of 10 to 35 MJ are expected soon thereafter. They propose that a laser system capable of generating fusion yields of 35 to 75 MJ at 10 to 15 Hz (i.e., {approx} 350- to 1000-MW fusion and {approx} 1.3 to 3.6 x 10{sup 20} n/s), coupled to a compact subdritical fission blanket, could be used to generate several GW of thermal power (GWth) while avoiding carbon dioxide emissions, mitigating nuclear proliferation concerns and minimizing the concerns associated with nuclear safety and long-term nuclear waste disposition. this Laser Inertial Fusion Energy (LIFE) based system is a logical extension of the NIF laser and the yields expec ted from the early ignition experiments on NIF. The LIFE concept is a once-through,s elf-contained closed fuel cycle and would have the following characteristics: (1) eliminate the need for spent fuel chemical separation facilities; (4) maintain the fission blanket subcritical at all times (k{sub eff} < 0.90); and (5) minimize future requirements for deep underground geological waste repositories and minimize actinide content in the end-of-life nuclear waste below the Department of Energy's (DOE's) attractiveness Level E (the lowest). Options to burn natural or depleted U, Th, U/Th mixtures, Spent Nuclear Fuel (SNF) without chemical separations of weapons-attractive actinide streams, and excess weapons Pu or highly enriched U (HEU) are possible and under consideration. Because the fission blanket is always subcritical and decay heat removal is possible via passive mechanisms, the technology is inherently safe. Many technical challenges must be met, but

  16. Energy-resolved photoemission studies of Be-containing surfaces for fusion; Energievariierte Photoemissionsstudien an berylliumhaltigen Oberflaechen fuer die Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Koeppen, Martin

    2013-02-04

    Fusion research aims at the exploitation of the deuterium-tritium reaction for energy production. Next step on the roadmap is the construction of the experimental reactor ITER. The three elements beryllium, carbon and tungsten are to be used as armour materials for the vacuum vessel. After erosion due to plasma processes, these materials are transported and redeposited together with plasma impurities like oxygen from surface oxides. This leads to the formation of compounds by chemical reactions and diffusive processes, induced both by elevated temperatures and implantation of energetic particles. Due to the complexity of the induced surface processes, a method is required which is capable of both qualitative and quantitative analysis of the involved chemical species. X-ray photoelectron spectroscopy (XPS) provides the chemical analysis. Since diffusive processes play an important role in solid-state reactions, a depth-resolved method is required. In this work, energy-resolved XPS using synchrotron radiation with variable photon energies is extended towards a quantitative depth-resolved analysis. For the quantitative analysis a new model is derived which calculates the depth-resolved composition and the respective composition-dependent electron inelastic mean free path in a self-consistent way. Input is the XPS data which is normalized with all parameters influencing the photoelectron intensities. This fully quantitative model is applied to describe the interaction of energetic oxygen ions with the beryllium-tungsten alloy Be{sub 2}W. Oxygen ions from the plasma are able to interact with plasma facing materials. Formation of Be{sub 2}W is to be expected at the first wall and in the divertor region of ITER. Irradiation of this alloy leads to its decompositions. After decomposition, formation of beryllium oxide BeO is preferred compared to formation of tungsten oxides. Heating to 600K leads to chemical reduction of tungsten oxides. Metallic Be acts as reduction agent

  17. Heat of Fusion Storage with High Solar Fraction for Solar Low Energy Buildings

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Furbo, Simon

    2006-01-01

    to achieve 100% coverage of space heating and domestic hot water in a low energy house in a Danish climate with a solar heating system with 36 m² flat plate solar collector and approximately 10 m³ storage with sodium acetate. A traditional water storage solution aiming at 100% coverage will require a storage...... of the storage to cool down below the melting point without solidification preserving the heat of fusion energy. If the supercooled storage reaches the surrounding temperature no heat loss will take place until the supercooled salt is activated. The investigation shows that this concept makes it possible...

  18. Liquid Metals as Plasma-facing Materials for Fusion Energy Systems: From Atoms to Tokamaks

    Energy Technology Data Exchange (ETDEWEB)

    Stone, Howard A. [Princeton Univ., NJ (United States); Koel, Bruce E. [Princeton Univ., NJ (United States); Bernasek, Steven L. [Princeton Univ., NJ (United States); Carter, Emily A. [Princeton Univ., NJ (United States); Debenedetti, Pablo G. [Princeton Univ., NJ (United States); Panagiotopoulos, Athanassios Z. [Princeton Univ., NJ (United States)

    2017-06-23

    The objective of our studies was to advance our fundamental understanding of liquid metals as plasma-facing materials for fusion energy systems, with a broad scope: from atoms to tokamaks. The flow of liquid metals offers solutions to significant problems of the plasma-facing materials for fusion energy systems. Candidate metals include lithium, tin, gallium, and their eutectic combinations. However, such liquid metal solutions can only be designed efficiently if a range of scientific and engineering issues are resolved that require advances in fundamental fluid dynamics, materials science and surface science. In our research we investigated a range of significant and timely problems relevant to current and proposed engineering designs for fusion reactors, including high-heat flux configurations that are being considered by leading fusion energy groups world-wide. Using experimental and theoretical tools spanning atomistic to continuum descriptions of liquid metals, and bridging surface chemistry, wetting/dewetting and flow, our research has advanced the science and engineering of fusion energy materials and systems. Specifically, we developed a combined experimental and theoretical program to investigate flows of liquid metals in fusion-relevant geometries, including equilibrium and stability of thin-film flows, e.g. wetting and dewetting, effects of electromagnetic and thermocapillary fields on liquid metal thin-film flows, and how chemical interactions and the properties of the surface are influenced by impurities and in turn affect the surface wetting characteristics, the surface tension, and its gradients. Because high-heat flux configurations produce evaporation and sputtering, which forces rearrangement of the liquid, and any dewetting exposes the substrate to damage from the plasma, our studies addressed such evaporatively driven liquid flows and measured and simulated properties of the different bulk phases and material interfaces. The range of our studies

  19. Accident consequences analysis of the HYLIFE-II inertial fusion energy power plant design

    Science.gov (United States)

    Reyes, S.; Latkowski, J. F.; Gomez del Rio, J.; Sanz, J.

    2001-05-01

    Previous studies of the safety and environmental aspects of the HYLIFE-II inertial fusion energy power plant design have used simplistic assumptions in order to estimate radioactivity releases under accident conditions. Conservatisms associated with these traditional analyses can mask the actual behavior of the plant and have revealed the need for more accurate modeling and analysis of accident conditions and radioactivity mobilization mechanisms. In the present work, computer codes traditionally used for magnetic fusion safety analyses (CHEMCON, MELCOR) have been applied for simulating accident conditions in a simple model of the HYLIFE-II IFE design. Here we consider a severe loss of coolant accident (LOCA) in conjunction with simultaneous failures of the beam tubes (providing a pathway for radioactivity release from the vacuum vessel towards the confinement) and of the two barriers surrounding the chamber (inner shielding and confinement building itself). Even though confinement failure would be a very unlikely event it would be needed in order to produce significant off-site doses. CHEMCON code allows calculation of long-term temperature transients in fusion reactor first wall, blanket, and shield structures resulting from decay heating. MELCOR is used to simulate a wide range of physical phenomena including thermal-hydraulics, heat transfer, aerosol physics and fusion product transport and release. The results of these calculations show that the estimated off-site dose is less than 5 mSv (0.5 rem), which is well below the value of 10 mSv (1 rem) given by the DOE Fusion Safety Standards for protection of the public from exposure to radiation during off-normal conditions.

  20. Accident consequences analysis of the HYLIFE-II inertial fusion energy power plant design

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, S; Gomez del Rio, J; Sanz, J

    2000-02-23

    Previous studies of the safety and environmental (S and E) aspects of the HYLIFE-II inertial fusion energy (IFE) power plant design have used simplistic assumptions in order to estimate radioactivity releases under accident conditions. Conservatisms associated with these traditional analyses can mask the actual behavior of the plant and have revealed the need for more accurate modeling and analysis of accident conditions and radioactivity mobilization mechanisms. In the present work a set of computer codes traditionally used for magnetic fusion safety analyses (CHEMCON, MELCOR) has been applied for simulating accident conditions in a simple model of the HYLIFE-II IFE design. Here the authors consider a severe lost of coolant accident (LOCA) producing simultaneous failures of the beam tubes (providing a pathway for radioactivity release from the vacuum vessel towards the containment) and of the two barriers surrounding the chamber (inner shielding and containment building it self). Even though containment failure would be a very unlikely event it would be needed in order to produce significant off-site doses. CHEMCON code allows calculation of long-term temperature transients in fusion reactor first wall, blanket, and shield structures resulting from decay heating. MELCOR is used to simulate a wide range of physical phenomena including thermal-hydraulics, heat transfer, aerosol physics and fusion product release and transport. The results of these calculations show that the estimated off-site dose is less than 6 mSv (0.6 rem), which is well below the value of 10 mSv (1 rem) given by the DOE Fusion Safety Standards for protection of the public from exposure to radiation during off-normal conditions.

  1. The Complete Burning of Weapons Grade Plutonium and Highly Enriched Uranium with (Laser Inertial Fusion-Fission Energy) LIFE Engine

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, J C; Diaz de la Rubia, T; Moses, E

    2008-12-23

    The National Ignition Facility (NIF) project, a laser-based Inertial Confinement Fusion (ICF) experiment designed to achieve thermonuclear fusion ignition and burn in the laboratory, is under construction at the Lawrence Livermore National Laboratory (LLNL) and will be completed in April of 2009. Experiments designed to accomplish the NIF's goal will commence in late FY2010 utilizing laser energies of 1 to 1.3 MJ. Fusion yields of the order of 10 to 20 MJ are expected soon thereafter. Laser initiated fusion-fission (LIFE) engines have now been designed to produce nuclear power from natural or depleted uranium without isotopic enrichment, and from spent nuclear fuel from light water reactors without chemical separation into weapons-attractive actinide streams. A point-source of high-energy neutrons produced by laser-generated, thermonuclear fusion within a target is used to achieve ultra-deep burn-up of the fertile or fissile fuel in a sub-critical fission blanket. Fertile fuels including depleted uranium (DU), natural uranium (NatU), spent nuclear fuel (SNF), and thorium (Th) can be used. Fissile fuels such as low-enrichment uranium (LEU), excess weapons plutonium (WG-Pu), and excess highly-enriched uranium (HEU) may be used as well. Based upon preliminary analyses, it is believed that LIFE could help meet worldwide electricity needs in a safe and sustainable manner, while drastically shrinking the nation's and world's stockpile of spent nuclear fuel and excess weapons materials. LIFE takes advantage of the significant advances in laser-based inertial confinement fusion that are taking place at the NIF at LLNL where it is expected that thermonuclear ignition will be achieved in the 2010-2011 timeframe. Starting from as little as 300 to 500 MW of fusion power, a single LIFE engine will be able to generate 2000 to 3000 MWt in steady state for periods of years to decades, depending on the nuclear fuel and engine configuration. Because the fission

  2. Fusion Simulation Project. Workshop sponsored by the U.S. Department of Energy Rockville, MD, May 16-18, 2007

    Energy Technology Data Exchange (ETDEWEB)

    None

    2007-05-16

    The mission of the Fusion Simulation Project is to develop a predictive capability for the integrated modeling of magnetically confined plasmas. This FSP report adds to the previous activities that defined an approach to integrated modeling in magnetic fusion. These previous activities included a Fusion Energy Sciences Advisory Committee panel that was charged to study integrated simulation in 2002. The report of that panel [Journal of Fusion Energy 20, 135 (2001)] recommended the prompt initiation of a Fusion Simulation Project. In 2003, the Office of Fusion Energy Sciences formed a steering committee that developed a project vision, roadmap, and governance concepts [Journal of Fusion Energy 23, 1 (2004)]. The current FSP planning effort involved forty-six physicists, applied mathematicians and computer scientists, from twenty-one institutions, formed into four panels and a coordinating committee. These panels were constituted to consider: Status of Physics Components, Required Computational and Applied Mathematics Tools, Integration and Management of Code Components, and Project Structure and Management. The ideas, reported here, are the products of these panels, working together over several months and culminating in a three-day workshop in May 2007.

  3. Fusion Simulation Project. Workshop Sponsored by the U.S. Department of Energy, Rockville, MD, May 16-18, 2007

    Energy Technology Data Exchange (ETDEWEB)

    Kritz, A.; Keyes, D.

    2007-05-18

    The mission of the Fusion Simulation Project is to develop a predictive capability for the integrated modeling of magnetically confined plasmas. This FSP report adds to the previous activities that defined an approach to integrated modeling in magnetic fusion. These previous activities included a Fusion Energy Sciences Advisory Committee panel that was charged to study integrated simulation in 2002. The report of that panel [Journal of Fusion Energy 20, 135 (2001)] recommended the prompt initiation of a Fusion Simulation Project. In 2003, the Office of Fusion Energy Sciences formed a steering committee that developed a project vision, roadmap, and governance concepts [Journal of Fusion Energy 23, 1 (2004)]. The current FSP planning effort involved forty-six physicists, applied mathematicians and computer scientists, from twenty-one institutions, formed into four panels and a coordinating committee. These panels were constituted to consider: Status of Physics Components, Required Computational and Applied Mathematics Tools, Integration and Management of Code Components, and Project Structure and Management. The ideas, reported here, are the products of these panels, working together over several months and culminating in a three-day workshop in May 2007.

  4. High Temperature Fusion Reactor Cooling Using Brayton Cycle Based Partial Energy Conversion

    Science.gov (United States)

    Juhasz, Albert J.; Sawicki, Jerzy T.

    2003-01-01

    For some future space power systems using high temperature nuclear heat sources most of the output energy will be used in other than electrical form, and only a fraction of the total thermal energy generated will need to be converted to electrical work. The paper describes the conceptual design of such a partial energy conversion system, consisting of a high temperature fusion reactor operating in series with a high temperature radiator and in parallel with dual closed cycle gas turbine (CCGT) power systems, also referred to as closed Brayton cycle (CBC) systems, which are supplied with a fraction of the reactor thermal energy for conversion to electric power. Most of the fusion reactor's output is in the form of charged plasma which is expanded through a magnetic nozzle of the interplanetary propulsion system. Reactor heat energy is ducted to the high temperature series radiator utilizing the electric power generated to drive a helium gas circulation fan. In addition to discussing the thermodynamic aspects of the system design the authors include a brief overview of the gas turbine and fan rotor-dynamics and proposed bearing support technology along with performance characteristics of the three phase AC electric power generator and fan drive motor.

  5. Targeting Low-Energy Ballistic Lunar Transfers

    Science.gov (United States)

    Parker, Jeffrey S.

    2010-01-01

    Numerous low-energy ballistic transfers exist between the Earth and Moon that require less fuel than conventional transfers, but require three or more months of transfer time. An entirely ballistic lunar transfer departs the Earth from a particular declination at some time in order to arrive at the Moon at a given time along a desirable approach. Maneuvers may be added to the trajectory in order to adjust the Earth departure to meet mission requirements. In this paper, we characterize the (Delta)V cost required to adjust a low-energy ballistic lunar transfer such that a spacecraft may depart the Earth at a desirable declination, e.g., 28.5(white bullet), on a designated date. This study identifies the optimal locations to place one or two maneuvers along a transfer to minimize the (Delta)V cost of the transfer. One practical application of this study is to characterize the launch period for a mission that aims to launch from a particular launch site, such as Cape Canaveral, Florida, and arrive at a particular orbit at the Moon on a given date using a three-month low-energy transfer.

  6. Progress in accident analysis of the HYLIFE-II inertial fusion energy power plant design

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, S; Latkowski, J F; Gomez del Rio, J; Sanz, J

    2000-10-11

    The present work continues our effort to perform an integrated safety analysis for the HYLIFE-II inertial fusion energy (IFE) power plant design. Recently we developed a base case for a severe accident scenario in order to calculate accident doses for HYLIFE-II. It consisted of a total loss of coolant accident (LOCA) in which all the liquid flibe (Li{sub 2}BeF{sub 4}) was lost at the beginning of the accident. Results showed that the off-site dose was below the limit given by the DOE Fusion Safety Standards for public protection in case of accident, and that his dose was dominated by the tritium released during the accident.

  7. Magnet safety and reliability in magnetic fusion energy systems. A summary report

    Energy Technology Data Exchange (ETDEWEB)

    Powell, J; Hsieh, D; Lehner, J; Reich, M; Yu, W Y

    1977-02-01

    The results of a two year study on magnet safety as it applies to Magnetic Fusion Energy Reactors and influences current program planning and experimental magnet design are presented in this summary report. Existing experience with superconducting magnet design and operation has been reviewed with the help of many active workers in this field and related to general reactor safety studies and techniques using the vast body of work generated in fission reactor safety programs as an illustrative reference base. A principal conclusion is that the inclusion of safety planning and design as a program component even at this early stage in Magnetic Fusion Reactor Development will save a great deal of money, time and design readjustment in the total thirty year program now envisaged.

  8. Coarse-grained molecular dynamics study of membrane fusion: Curvature effects on free energy barriers along the stalk mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Kawamoto, Shuhei; Shinoda, Wataru, E-mail: w.shinoda@apchem.nagoya-u.ac.jp [Department of Applied Chemistry, Nagoya University, Furo-cho, Chikusa-ku, Nagoya, Aichi 464-8603 (Japan); Klein, Michael L. [Institute for Computational Molecular Science, Temple University, SERC Building 1925 North 12th Street, Philadelphia, Pennsylvania 19122 (United States)

    2015-12-28

    The effects of membrane curvature on the free energy barrier for membrane fusion have been investigated using coarse-grained molecular dynamics (CG-MD) simulations, assuming that fusion takes place through a stalk intermediate. Free energy barriers were estimated for stalk formation as well as for fusion pore formation using the guiding potential method. Specifically, the three different geometries of two apposed membranes were considered: vesicle–vesicle, vesicle–planar, and planar–planar membranes. The free energy barriers for the resulting fusion were found to depend importantly on the fusing membrane geometries; the lowest barrier was obtained for vesicular membranes. Further, lipid sorting was observed in fusion of the mixed membranes of dimyristoyl phosphatidylcholine and dioleoyl phosphatidylethanolamine (DOPE). Specifically, DOPE molecules were found to assemble around the stalk to support the highly negative curved membrane surface. A consistent result for lipid sorting was observed when a simple continuum model (CM) was used, where the Helfrich energy and mixing entropy of the lipids were taken into account. However, the CM predicts a much higher free energy barrier than found using CG-MD. This discrepancy originates from the conformational changes of lipids, which were not considered in the CM. The results of the CG-MD simulations reveal that a large conformational change in the lipid takes place around the stalk region, which results in a reduction of free energy barriers along the stalk mechanism of membrane fusion.

  9. Coarse-grained molecular dynamics study of membrane fusion: Curvature effects on free energy barriers along the stalk mechanism.

    Science.gov (United States)

    Kawamoto, Shuhei; Klein, Michael L; Shinoda, Wataru

    2015-12-28

    The effects of membrane curvature on the free energy barrier for membrane fusion have been investigated using coarse-grained molecular dynamics (CG-MD) simulations, assuming that fusion takes place through a stalk intermediate. Free energy barriers were estimated for stalk formation as well as for fusion pore formation using the guiding potential method. Specifically, the three different geometries of two apposed membranes were considered: vesicle-vesicle, vesicle-planar, and planar-planar membranes. The free energy barriers for the resulting fusion were found to depend importantly on the fusing membrane geometries; the lowest barrier was obtained for vesicular membranes. Further, lipid sorting was observed in fusion of the mixed membranes of dimyristoyl phosphatidylcholine and dioleoyl phosphatidylethanolamine (DOPE). Specifically, DOPE molecules were found to assemble around the stalk to support the highly negative curved membrane surface. A consistent result for lipid sorting was observed when a simple continuum model (CM) was used, where the Helfrich energy and mixing entropy of the lipids were taken into account. However, the CM predicts a much higher free energy barrier than found using CG-MD. This discrepancy originates from the conformational changes of lipids, which were not considered in the CM. The results of the CG-MD simulations reveal that a large conformational change in the lipid takes place around the stalk region, which results in a reduction of free energy barriers along the stalk mechanism of membrane fusion.

  10. The effect of low energy helium ion irradiation on tungsten-tantalum (W-Ta) alloys under fusion relevant conditions

    Science.gov (United States)

    Gonderman, S.; Tripathi, J. K.; Novakowski, T. J.; Sizyuk, T.; Hassanein, A.

    2017-08-01

    Currently, tungsten remains the best candidate for plasma-facing components (PFCs) for future fusion devices because of its high melting point, low erosion, and strong mechanical properties. However, continued investigation has shown tungsten to undergo severe morphology changes under fusion-like conditions. These results motivate the study of innovative PFC materials which are resistant to surface morphology evolution. The goal of this work is to examine tungsten-tantalum (W-Ta) alloys, a potential PFC material, and their response to low energy helium ion irradiation. Specifically, W-Ta samples are exposed to 100 eV helium irradiations with a flux of 1.15 × 1021 ions m-2 s-1, at 873 K, 1023 K, and 1173 K for 1 h duration. Scanning electron microscopy (SEM) reveals significant changes in surface deterioration due to helium ion irradiation as a function of both temperature and tantalum concentration in W-Ta samples. X-Ray Diffraction (XRD) studies show a slight lattice parameter expansion in W-Ta alloy samples compared to pure W samples. The observed lattice parameter expansion in W-Ta alloy samples (proportional to increasing Ta wt.% concentrations) reflect significant differences observed in the evolution of surface morphology, i.e., fuzz development processes for both increasing Ta wt.% concentration and target temperature. These results suggest a correlation between the observed morphology differences and the induced crystal structure change caused by the presence of tantalum. Shifts in the XRD peaks before and after 100 eV helium irradiation with a flux of 1.15 × 1021 ions m-2 s-1, 1023 K, for 1 h showed a significant difference in the magnitude of the shift. This has suggested a possible link between the atomic spacing of the material and the accumulated damage. Ongoing research is needed on W-Ta alloys and other innovative materials for their application as irradiation resistant materials in future fusion or irradiation environments.

  11. Study for fusion-fission and quasifission in reactions using {sup 238}U target nucleus

    Energy Technology Data Exchange (ETDEWEB)

    Nishio, Katsuhisa, E-mail: nishio.katsuhisa@jaea.go.jp [Advanced Science Reserch Center, Japan Atomic Energy Agency, Tokai, Ibraki 319-1195 (Japan)

    2011-02-01

    Fragment mass distributions for fission after full momentum transfer (FMT) were measured for the {sup 30}Si,{sup 31}P,{sup 34,36}S,{sup 40}Ar + {sup 238}U reactions at bombarding energies around the Coulomb barrier. The experiment was carried out at the JAEA tandem accelerator facility. We observed strong variation of the mass distribution on beam energy and projectile nucleus. In the reaction of {sup 36}S +{sup 238}U we observed a transition from symmetry to asymmetry mass distributions when the beam energies were decreased from the above-barrier to sub-barrier values. The mass asymmetry was A{sub L} /A{sub H} = 74/200, which corresponds to the fission valley leading to the nuclei close to the doubly closed-shell nuclei {sup 78}Ni /{sup 208}Pb. The fission channel is populated by quasifission, which is the disintegration without forming the compound nucleus. The incident-energy dependence is strongly correlated with the prolate deformation of {sup 238}U and the orientation at the initial impact. The results indicate that the reaction starting at the polar collisions on {sup 238}U has larger quasifission probability. The mass distributions are nicely reproduced by a model calculation using Langevin equation. The {sup 40}Ar + {sup 238}U reaction also has the similar mass asymmetry (A{sub L}/A{sub H} {approx} 78/200) in quasifission. In the reactions of {sup 31}P + {sup 238}U and {sup 30}Si + {sup 238}U, mass asymmetries are A{sub L}/A{sub H} 81/188 and 90/178, respectively. The results suggest that the system produced by the reaction using lighter projectile approaches closer to the shape of the compound nucleus even when quasifission occurs. In the reactions of {sup 30}Si +{sup 238}U and {sup 34}S+ {sup 238}U, we also measured the evaporation residue (ER) cross sections to obtain information on the fusion probability. From the ER cross sections for the {sup 34}S+{sup 238}U reaction it was suggested that the symmetric fission is also dominated by quasifission.

  12. Nuclear fusion as an energy option for the 21st Century; La fusion nuclear como opcion energetica para el Siglo 21

    Energy Technology Data Exchange (ETDEWEB)

    Herrera V, J.J.E. [Instituto de Ciencias Nucleares, UNAM, 04510 Mexico D.F. (Mexico)

    2007-07-01

    Under the point of view of the engineering, it is even a long road to travel before it is possible to build an economically competitive fusion reactor. In contrast, for each obstacle in the road different forms can be devised of approaching it, and the future is promising, whenever the necessary financing exists to support the investigations. The fusion can contribute to satisfy the energy necessities for the development of the civilization in a sustainable way, to medium term if it is used in symbiosis with the fission reactors, providing fuel and transmuting radioactive waste. In any event, this focus should be developed spreading the safety primarily in mind, and so the processes are economically competitive. Just as it can be appreciate in the sections of this work, the investigation in fusion requires of determination, discipline, and it is not for the weak of spirit. While other energy sources, particularly the renewable ones, they should take advantage in Mexico, the fusion is the more plaintiff, and it requires of scientific and technological resources of forefront. In certain form, together with the fission technology, it determines the crossroad that separates to the developed countries of those that are 'developing'. Brazil, South Korea, China and India, aware of the necessity of enough energy sources to sustain their development, they have already taken the initiative to accept the challenge. It corresponds Mexico to follow the example, or to stay in the status of 'developing country.' (Author)

  13. Mechanisms of influenza viral membrane fusion.

    Science.gov (United States)

    Blijleven, Jelle S; Boonstra, Sander; Onck, Patrick R; van der Giessen, Erik; van Oijen, Antoine M

    2016-12-01

    Influenza viral particles are enveloped by a lipid bilayer. A major step in infection is fusion of the viral and host cellular membranes, a process with large kinetic barriers. Influenza membrane fusion is catalyzed by hemagglutinin (HA), a class I viral fusion protein activated by low pH. The exact nature of the HA conformational changes that deliver the energy required for fusion remains poorly understood. This review summarizes our current knowledge of HA structure and dynamics, describes recent single-particle experiments and modeling studies, and discusses their role in understanding how multiple HAs mediate fusion. These approaches provide a mechanistic picture in which HAs independently and stochastically insert into the target membrane, forming a cluster of HAs that is collectively able to overcome the barrier to membrane fusion. The new experimental and modeling approaches described in this review hold promise for a more complete understanding of other viral fusion systems and the protein systems responsible for cellular fusion.

  14. Enhanced neutralization potency of botulinum neurotoxin antibodies using a red blood cell-targeting fusion protein.

    Directory of Open Access Journals (Sweden)

    Sharad P Adekar

    Full Text Available Botulinum neurotoxin (BoNT potently inhibits cholinergic signaling at the neuromuscular junction. The ideal countermeasures for BoNT exposure are monoclonal antibodies or BoNT antisera, which form BoNT-containing immune complexes that are rapidly cleared from the general circulation. Clearance of opsonized toxins may involve complement receptor-mediated immunoadherence to red blood cells (RBC in primates or to platelets in rodents. Methods of enhancing immunoadherence of BoNT-specific antibodies may increase their potency in vivo. We designed a novel fusion protein (FP to link biotinylated molecules to glycophorin A (GPA on the RBC surface. The FP consists of an scFv specific for murine GPA fused to streptavidin. FP:mAb:BoNT complexes bound specifically to the RBC surface in vitro. In a mouse model of BoNT neutralization, the FP increased the potency of single and double antibody combinations in BoNT neutralization. A combination of two antibodies with the FP gave complete neutralization of 5,000 LD50 BoNT in mice. Neutralization in vivo was dependent on biotinylation of both antibodies and correlated with a reduction of plasma BoNT levels. In a post-exposure model of intoxication, FP:mAb complexes gave complete protection from a lethal BoNT/A1 dose when administered within 2 hours of toxin exposure. In a pre-exposure prophylaxis model, mice were fully protected for 72 hours following administration of the FP:mAb complex. These results demonstrate that RBC-targeted immunoadherence through the FP is a potent enhancer of BoNT neutralization by antibodies in vivo.

  15. Relative importance of energy dependent diffuseness parameter and barrier position in the analysis of fusion excitation function data

    Directory of Open Access Journals (Sweden)

    Kharab Rajesh

    2014-03-01

    Full Text Available We have investigated the relative importance of the energy dependence of diffuseness parameter and barrier position in the description of the fusion excitation function data of some heavy ion systems in near barrier energy region. The effects of the energy dependent diffuseness parameter are found to be much more prominent in comparison to those of barrier position.

  16. Low-energy d+d fusion via the Trojan Horse Method

    Science.gov (United States)

    Tumino, A.; Spitaleri, C.; Mukhamedzhanov, A. M.; Typel, S.; Aliotta, M.; Burjan, V.; Gimenez del Santo, M.; Kiss, G. G.; Kroha, V.; Hons, Z.; La Cognata, M.; Lamia, L.; Mrazek, J.; Pizzone, R. G.; Piskor, S.; Rapisarda, G. G.; Romano, S.; Sergi, M. L.; Spartà, R.

    2013-04-01

    The 2H(d,p)3H and 2H(d,n)3He reactions have been recently investigated from Edd=1.5 MeV down to 2 keV, by means of the Trojan Horse Method (THM) applied to the Quasi Free 3He+d interaction at 18 MeV [1]. The knowledge of their fusion cross section at low energies is of interest for pure and applied physics. Both reactions belong to the network of processes to fuel the first inertial confinement fusion reactors in the range of kT= 1 to 30 keV. These energies overlap with the burning temperatures of deuterium in the Pre-main sequence of stellar evolution. They are key processes in the Standard Big Bang Nucleosynthesis (SBBN), in an energy region from 50 to 300 keV and experimental data at least up to 1 MeV are required for an accurate calculation of the reaction rate. Providing experimental data for both channels from a single experiment and over the entire energy range of interest is crucial for an accurate calculation of the reaction rates. This is what has been obtained from the present Trojan Horse (TH) investigation with new reaction rates which deviate by more than 20% from available direct data. This represents also the first pioneering experiment in quasi free regime where the charged spectator is detected.

  17. Neutron-energy-dependent defect production cross sections for fission and fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Odette, G.R.; Doiron, D.R.

    1976-06-01

    Neutron cross sections for displacements and post-short-term cascade annealing defects are derived from nuclear kinematics calculations of primary atomic recoil energy distributions and the number of secondary defects produced per primary as a function of recoil energy. For the first time, recoil kinematics of charged- and multiple-particle emission reactions are treated rigorously using a compound-nucleus evaporation spectrum nuclear model. Secondary-defect production functions, derived from computer simulation experiments, are taken from the literature. Spectral-averaged defect production cross sections for a fusion reactor first-wall-type environment are on the order of 1.5 to 2.5 times those for a fast fission reactor core-type spectrum. The indicated range of uncertainty is primarily due to secondary-defect production model sensitivity. Nuclear model and data errors are expected to become more significant at high neutron energies, greater than approximately 20 MeV. Fusion reactor environments are found to produce some very energetic recoils and high-energy release events due to charged-particle reactions such as (n,..cap alpha..).

  18. Antibody-independent targeted quantification of TMPRSS2-ERG fusion protein products in prostate cancer.

    Science.gov (United States)

    He, Jintang; Sun, Xuefei; Shi, Tujin; Schepmoes, Athena A; Fillmore, Thomas L; Petyuk, Vladislav A; Xie, Fang; Zhao, Rui; Gritsenko, Marina A; Yang, Feng; Kitabayashi, Naoki; Chae, Sung-Suk; Rubin, Mark A; Siddiqui, Javed; Wei, John T; Chinnaiyan, Arul M; Qian, Wei-Jun; Smith, Richard D; Kagan, Jacob; Srivastava, Sudhir; Rodland, Karin D; Liu, Tao; Camp, David G

    2014-10-01

    Fusions between the transmembrane protease serine 2 (TMPRSS2) and ETS related gene (ERG) represent one of the most specific biomarkers that define a distinct molecular subtype of prostate cancer. Studies of TMPRSS2-ERG gene fusions have seldom been performed at the protein level, primarily due to the lack of high-quality antibodies suitable for quantitative studies. Herein, we applied a recently developed PRISM (high-pressure high-resolution separations with intelligent selection and multiplexing)-SRM (selected reaction monitoring) strategy for quantifying ERG protein in prostate cancer cell lines and tumors. The highly sensitive PRISM-SRM assays provided confident detection of 6 unique ERG peptides in both TMPRSS2-ERG positive cell lines and tissues, but not in cell lines or tissues lacking the TMPRSS2-ERG rearrangement, clearly indicating that ERG protein expression is significantly increased in the presence of the TMPRSS2-ERG gene fusion. Significantly, our results provide evidence that two distinct ERG protein isoforms are simultaneously expressed in TMPRSS2-ERG positive samples as evidenced by the concomitant detection of two mutually exclusive peptides in two patient tumors and in the VCaP prostate cancer cell line. Three peptides, shared across almost all fusion protein products, were determined to be the most abundant peptides, providing "signature" peptides for detection of ERG over-expression resulting from TMPRSS2-ERG gene fusion. The PRISM-SRM assays provide valuable tools for studying TMPRSS2-ERG gene fusion protein products in prostate cancer.

  19. The Science and Technology Challenges of the Plasma-Material Interface for Magnetic Fusion Energy

    Science.gov (United States)

    Whyte, Dennis

    2013-09-01

    The boundary plasma and plasma-material interactions of magnetic fusion devices are reviewed. The boundary of magnetic confinement devices, from the high-temperature, collisionless pedestal through to the surrounding surfaces and the nearby cold high-density collisional plasmas, encompasses an enormous range of plasma and material physics, and their integrated coupling. Due to fundamental limits of material response the boundary will largely define the viability of future large MFE experiments (ITER) and reactors (e.g. ARIES designs). The fusion community faces an enormous knowledge deficit in stepping from present devices, and even ITER, towards fusion devices typical of that required for efficient energy production. This deficit will be bridged by improving our fundamental science understanding of this complex interface region. The research activities and gaps are reviewed and organized to three major axes of challenges: power density, plasma duration, and material temperature. The boundary can also be considered a multi-scale system of coupled plasma and material science regulated through the non-linear interface of the sheath. Measurement, theory and modeling across these scales are reviewed, with a particular emphasis on establishing the use dimensionless parameters to understand this complex system. Proposed technology and science innovations towards solving the PMI/boundary challenges will be examined. Supported by US DOE award DE-SC00-02060 and cooperative agreement DE-FC02-99ER54512.

  20. Medical Image Fusion Algorithm based on Local Average Energy-Motivated PCNN in NSCT Domain

    Directory of Open Access Journals (Sweden)

    Huda Ahmed

    2016-10-01

    Full Text Available Medical Image Fusion (MIF can improve the performance of medical diagnosis, treatment planning and image-guided surgery significantly through providing high-quality and rich-information medical images. Traditional MIF techniques suffer from common drawbacks such as: contrast reduction, edge blurring and image degradation. Pulse-coupled Neural Network (PCNN based MIF techniques outperform the traditional methods in providing high-quality fused images due to its global coupling and pulse synchronization property; however, the selection of significant features that motivate the PCNN is still an open problem and plays a major role in measuring the contribution of each source image into the fused image. In this paper, a medical image fusion algorithm is proposed based on the Non-subsampled Contourlet Transform (NSCT and the Pulse-Coupled Neural Network (PCNN to fuse images from different modalities. Local Average Energy is used to motivate the PCNN due to its ability to capture salient features of the image such as edges, contours and textures. The proposed approach produces a high quality fused image with high contrast and improved content in comparison with other image fusion techniques without loss of significant details on both levels: the visual and the quantitative.

  1. National Target of Energy conservation and Policy Measures

    Energy Technology Data Exchange (ETDEWEB)

    Shim, S.R. [Korea Energy Economics Institute, Euiwang (Korea)

    2001-12-01

    This study investigates impacts of energy saving policies on the national economy in Korea. An energy saving policy for a specific sector causes changes in energy consumption patterns of a target sector as well as the others. In addition to its positive bearing on energy consumption, such policy can change energy prices, output, employment, consumer price levels, and resources allocation in the economy. In this context, successful analyses of energy saving policies need to consider such interactions to develop and evaluate the best policy alternatives. Thus, this study employs a Korean computable general equilibrium model to analyze optimal energy saving targets, and corresponding programs for each sector in the economy. The R and D investment policy in the energy sector is the most effective one since it is projected to increase real GNP and GDP, decreasing energy consumption. The policy is accordingly considered as one of so-called no-regret policies. And, the policy is evaluated to be appropriate for the energy intensive industries and transportation sectors. The government loan program for energy efficiency improvement is also predicted to raise GNP although it may have a negative impact on trade balance. And, the policy is observed to be suitable for the transportation and household sectors. An energy saving effort with energy taxation is found to be cost-effective since its marginal cost of energy conservation is estimated to be much lower than about 80,000 won per ton of oil equivalent, the estimated benefit of energy conservation. It is recommended, however, that an additional energy tax be implemented with care, given the high level of existing energy taxes. The effectiveness of energy efficiency standards in the transportation, household, and commercial sectors varies depending on how prices of relevant energy using equipments and appliances change in response to the standards. Energy saving policies are adequately formulated and implemented for all the

  2. Computational Plasma Physics at the Bleeding Edge: Simulating Kinetic Turbulence Dynamics in Fusion Energy Sciences

    Science.gov (United States)

    Tang, William

    2013-04-01

    Advanced computing is generally recognized to be an increasingly vital tool for accelerating progress in scientific research in the 21st Century. The imperative is to translate the combination of the rapid advances in super-computing power together with the emergence of effective new algorithms and computational methodologies to help enable corresponding increases in the physics fidelity and the performance of the scientific codes used to model complex physical systems. If properly validated against experimental measurements and verified with mathematical tests and computational benchmarks, these codes can provide more reliable predictive capability for the behavior of complex systems, including fusion energy relevant high temperature plasmas. The magnetic fusion energy research community has made excellent progress in developing advanced codes for which computer run-time and problem size scale very well with the number of processors on massively parallel supercomputers. A good example is the effective usage of the full power of modern leadership class computational platforms from the terascale to the petascale and beyond to produce nonlinear particle-in-cell simulations which have accelerated progress in understanding the nature of plasma turbulence in magnetically-confined high temperature plasmas. Illustrative results provide great encouragement for being able to include increasingly realistic dynamics in extreme-scale computing campaigns to enable predictive simulations with unprecedented physics fidelity. Some illustrative examples will be presented of the algorithmic progress from the magnetic fusion energy sciences area in dealing with low memory per core extreme scale computing challenges for the current top 3 supercomputers worldwide. These include advanced CPU systems (such as the IBM-Blue-Gene-Q system and the Fujitsu K Machine) as well as the GPU-CPU hybrid system (Titan).

  3. Comparative evaluation of solar, fission, fusion, and fossil energy resources. Part 1: Solar energy

    Science.gov (United States)

    Williams, J. R.

    1974-01-01

    The utilization of solar energy to meet the energy needs of the U.S. is discussed. Topics discussed include: availability of solar energy, solar energy collectors, heating for houses and buildings, solar water heater, electric power generation, and ocean thermal power.

  4. Review of Burning Plasma Physics. Fusion Energy Sciences Advisory Committee (FESAC)

    Energy Technology Data Exchange (ETDEWEB)

    Berk, Herb [Univ. of Texas, Austin, TX (United States); Betti, Riccardo [Univ. of Rochester, NY (United States); Dahlburg, Jill [Univ. of Georgia, Athens, GA (United States); Freidberg, Jeff [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hopper, Bick [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Meade, Dale [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Navritil, Jerry [Columbia Univ., New York, NY (United States); Nevins, Bill [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ono, Masa [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Perkins, Rip [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Prager, Stewart [Univ. of Wisconsin, Madison, WI (United States); Schoenburg, Kurt [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Taylor, Tony [Univ. of Georgia, Athens, GA (United States); Uckan, Nermin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2001-09-01

    The next frontier in the quest for magnetic fusion energy is the development of a basic understanding of plasma behavior in the regime of strong self-heating, the so called “burning plasma” regime. The general consensus in the fusion community is that the exploration of this frontier requires a new, relatively large experimental facility - a burning plasma experiment. The motivation, justification, and steps required to build such a facility are the primary focus of our report. The specific goals of the report are as follows. First, the report describes the critical scientific and engineering phenomena that are expected to arise for the first time, or else in a strongly modified form, in a burning plasma. Second, the report shows that the capabilities of existing experiments are inadequate to investigate these phenomena, thereby providing a major justification for a new facility. Third, the report compares the features and predicted performance of the three major next generation burning plasma experiments under current consideration (ITER-FEAT, FIRE, and IGNITOR), which are aimed at addressing these problems. Deliberately, no selection of the best option is made or attempted since such a decision involves complex scientific and cost issues that are beyond the scope of the present panel report. Fourth, the report makes specific recommendations regarding a process to move the burning plasma program forward, including a procedure for choosing the best option and the future activities of the Next Step Option (NSO) program. Fifth, the report attempts to provide a proper perspective for the role of burning plasmas with respect to the overall U.S. fusion program. The introduction provides the basic background information required for understanding the context in which the U.S. fusion community thinks about burning plasma issues. It “sets the stage” for the remainder of the report.

  5. Targets IMage Energy Regional (TIMER) Model, Technical Documentation

    NARCIS (Netherlands)

    Vries B de; Vuuren D van; Elzen M den; Janssen M; MNV

    2002-01-01

    The Targets IMage Energy Regional simulation model, TIMER, is described in detail. This model was developed and used in close connection with the Integrated Model to Assess the Global Environment (IMAGE) 2.2. The system-dynamics TIMER model simulates the global energy system at an intermediate level

  6. The Targets/IMage Energy (TIME) 1.0 Model

    NARCIS (Netherlands)

    Vries B de; Wijngaart RA van den; MNV

    1996-01-01

    Documentation of the five submodels of Targets/IMage Energy (TIME) 1.0 model are presented. Energy Demand, Liquid Fuel (LF), Gaseous Fuel (GF), Solid Fuel (SF) and Electric Power Generation (EPG) are described in detail. Some results of the model calibration for the world 1900-1990 are presented as

  7. Antibody-independent Targeted Quantification of TMPRSS2-ERG Fusion Protein Products in Prostate Cancer

    Energy Technology Data Exchange (ETDEWEB)

    He, Jintang; Sun, Xuefei; Shi, Tujin; Schepmoes, Athena A.; Fillmore, Thomas L.; Petyuk, Vladislav A.; Xie, Fang; Zhao, Rui; Gritsenko, Marina A.; Yang, Feng; Kitabayashi, Naoki; Chae, Sung Suk; Rubin, Mark; Siddiqui, Javed; Wei, John; Chinnaiyan, Arul M.; Qian, Weijun; Smith, Richard D.; Kagan, Jacob; Srivastava, Sudhir; Rodland, Karin D.; Liu, Tao; Camp, David G.

    2014-10-01

    Fusions between the transmembrane protease serine 2 (TMPRSS2) and ETS related gene (ERG) represent one of the most specific biomarkers that define a distinct molecular subtype of prostate cancer. The studies on TMPRSS2-ERG gene fusions have seldom been performed at the protein level, primarily due to the lack of high-quality antibodies or an antibody-independent method that is sufficiently sensitive for detecting the truncated ERG protein products resulting from TMPRSS2-ERG gene fusions and alternative splicing. Herein, we applied a recently developed PRISM (high-pressure high-resolution separations with intelligent selection and multiplexing)-SRM (selected reaction monitoring) strategy for quantifying ERG protein in prostate cancer cell lines and tumors. The highly sensitive PRISM-SRM assays led to confident detection of 6 unique ERG peptides in either the TMPRSS2-ERG positive cell lines or tissues but not in the negative controls, indicating that ERG protein expression is highly correlated with TMPRSS2-ERG gene rearrangements. Significantly, our results demonstrated for the first time that at least two groups of ERG protein isoforms were simultaneously expressed at variable levels in TMPRSS2-ERG positive samples as evidenced by concomitant detection of two mutually exclusive peptides. Three peptides shared across almost all fusion protein products were determined to be the most abundant peptides, and hence can be used as “signature” peptides for detecting ERG overexpression resulting from TMPRSS2-ERG gene fusion. These PRISM-SRM assays provide valuable tools for studying TMPRSS2-ERG gene fusion protein products, thus improving our understanding of the role of TMPRSS2-ERG gene fusion in the biology of prostate cancer.

  8. Calculated Lattice Energies of Energetic Materials in a Prediction of their Heats of Fusion and Sublimation

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The paper specifies an unambiguous basic relationship between the published results of ab initio calculations of lattice energies,EL,and heats of sublimation,ΔHs,of individual energetic materials. In this relationship,the ΔHs value has been replaced by heats of fusion,ΔHm,tr. Thereby its unambiguity has been lost,and the similarity of details of molecular structure begins to be of decisive importance. The resulting partial relationships,together with the basic relationship,have been used for prediction of ΔHs,and ΔHm,tr values of technically attractive polynitro compounds.

  9. Design and testing of the 2 MV heavy ion injector for the Fusion Energy Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Abraham, W.; Benjegerdes, R.; Reginato, L.; Stoker, J.; Hipple, R.; Peters, C.; Pruyn, J.; Vanecek, D.; Yu, S.

    1995-04-01

    The Fusion Energy Research Group at the Lawrence Berkeley Laboratory has constructed and tested a pulsed 2 MV injector that produces a driver size beam of potassium ions. This paper describes the engineering aspects of this development which were generated in a closely coupled effort with the physics staff. Details of the ion source and beam transport physics are covered in another paper at this conference. This paper discusses the design details of the pulse generator, the ion source, the extractor, the diode column, and the electrostatic quadrupole column. Included will be the test results and operating experience of the complete injector.

  10. Proceedings of the Office of Fusion Energy/DOE workshop on ceramic matrix composites for structural applications in fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Jones, R.H. (Pacific Northwest Lab., Richland, WA (USA)); Lucas, G.E. (California Univ., Santa Barbara, CA (USA))

    1990-11-01

    A workshop to assess the potential application of ceramic matrix composites (CMCs) for structural applications in fusion reactors was held on May 21--22, 1990, at University of California, Santa Barbara. Participants included individuals familiar with materials and design requirements in fusion reactors, ceramic composite processing and properties and radiation effects. The primary focus was to list the feasibility issues that might limit the application of these materials in fusion reactors. Clear advantages for the use of CMCs are high-temperature operation, which would allow a high-efficiency Rankine cycle, and low activation. Limitations to their use are material costs, fabrication complexity and costs, lack of familiarity with these materials in design, and the lack of data on radiation stability at relevant temperatures and fluences. Fusion-relevant feasibility issues identified at this workshop include: hermetic and vacuum properties related to effects of matrix porosity and matrix microcracking; chemical compatibility with coolant, tritium, and breeder and multiplier materials, radiation effects on compatibility; radiation stability and integrity; and ability to join CMCs in the shop and at the reactor site, radiation stability and integrity of joints. A summary of ongoing CMC radiation programs is also given. It was suggested that a true feasibility assessment of CMCs for fusion structural applications could not be completed without evaluation of a material tailored'' to fusion conditions or at least to radiation stability. It was suggested that a follow-up workshop be held to design a tailored composite after the results of CMC radiation studies are available and the critical feasibility issues are addressed.

  11. Energy transfer between fusion biliproteins co-expressed with phycobiliprotein in Escherichia coli.

    Science.gov (United States)

    Ma, Qiong; Zhou, Nan; Zhou, Ming

    2016-10-01

    In cyanobacteria, phycobiliproteins (PBS) show excellent energy transfer among the chromophores absorbing over most of the visible. The energy transfers are used to study phycobilisome assembly and bioimaging. Using All4261GAF2(C81L) as energy donor, ApcE(1-240/Δ87-130) as energy acceptor, we co-expressed fusion protein ApcE(1-240/Δ87-130)::All4261GAF2(C81L) with phycobiliprotein in Escherichia Coli and studied the energy transfer between two protein domains. With N-terminal His6 tag, ApcE(1-240/Δ87-130)::All4261GAF2(C81L) cannot be purified by nickel-affinity column. We added six histidines in the C-terminal of ApcE(1-240/Δ87-130)::All4261GAF2(C81L) and co-expressed it with phycobiliprotein. ApcE(1-240/Δ87-130)::PCB-All4261GAF2(C81L)His6 was purified successfully and only singly chromophorylated at All4261GAF2(C81L)His6 domain. The singly chromophorylate ApcE(1-240/Δ87-130)::PCB-All4261GAF2(C81L)His6 was incubated with fresh PCB and the doubly chromophorylated PCB-ApcE(1-240/Δ87-130)::PCB-All4261GAF2(C81L)His6 was obtained. The double chromophored fusion protein absorbed light in the range of 615-660 nm, and fluoresced only at 668 nm. Photochemistry analysis showed that excitation energy transfer from the short-wavelength absorbing at All4261GAF2(C81L) domain was achieved successfully to the long-wavelength absorbing at the ApcE(1-240/Δ87-130) domain.

  12. Remotely sensed data fusion for offshore wind energy resource mapping; Fusion de donnees satellitaires pour la cartographie du potentiel eolien offshore

    Energy Technology Data Exchange (ETDEWEB)

    Ben Ticha, M.B

    2007-11-15

    Wind energy is a component of an energy policy contributing to a sustainable development. Last years, offshore wind parks have been installed offshore. These parks benefit from higher wind speeds and lower turbulence than onshore. To sit a wind park, it is necessary to have a mapping of wind resource. These maps are needed at high spatial resolution to show wind energy resource variations at the scale of a wind park. Wind resource mapping is achieved through the description of the spatial variations of statistical parameters characterizing wind climatology. For a precise estimation of these statistical parameters, high temporal resolution wind speed and direction measurements are needed. However, presently, there is no data source allying high spatial resolution and high temporal resolution. We propose a data fusion method taking advantage of the high spatial resolution of some remote sensing instruments (synthetic aperture radars) and the high temporal resolution of other remote sensing instruments (scatterometers). The data fusion method is applied to a case study and the results quality is assessed. The results show the pertinence of data fusion for the mapping of wind energy resource offshore. (author)

  13. Fabrication of polystyrene hollow microspheres as laser fusion targets by optimized density-matched emulsion technique and characterization

    Indian Academy of Sciences (India)

    K K Mishra; R K Khardekar; Rashmi Singh; H C Pant

    2002-07-01

    Inertial confinement fusion, frequently referred to as ICF, inertial fusion, or laser fusion, is a means of producing energy by imploding small hollow microspheres containing thermonuclear fusion fuel. Polymer microspheres, which are used as fuel containers, can be produced by solution-based micro-encapsulation technique better known as density-matched emulsion technique. The specifications of these microspheres are very rigorous, and various aspects of the emulsion hydrodynamics associated with their production are important in controlling the final product. This paper describes about the optimization of various parameters associated with density-matched emulsion method in order to improve the surface smoothness, wall thickness uniformity and sphericity of hollow polymer microspheres. These polymer microshells have been successfully fabricated in our lab, with 3–30 m wall thickness and 50–1600 m diameters. The sphericity and wall thickness uniformity are better than 99%. Elimination of vacuoles and high yield rate has been achieved by adopting the step-wise heating of W1/O/W2 emulsion for solvent removal.

  14. Genetic fusion of single-chain variable fragments to partial spider silk improves target detection in micro- and nanoarrays.

    Science.gov (United States)

    Thatikonda, Naresh; Delfani, Payam; Jansson, Ronnie; Petersson, Linn; Lindberg, Diana; Wingren, Christer; Hedhammar, My

    2016-03-01

    Immobilizing biomolecules with retained functionality and stability on solid supports is crucial for generation of sensitive immunoassays. However, upon use of conventional immobilization strategies, a major portion of the biomolecules (e.g. antibodies) frequently tends to lose their bioactivity. In this study, we describe a procedure to immobilize human single-chain variable fragment (scFv) via genetic fusion to partial spider silk, which have a high tendency to adhere to solid supports. Two scFvs, directed towards serum proteins, were genetically fused to partial spider silk proteins and expressed as silk fusion proteins in E. coli. Antigen binding ability of scFvs attached to a partial silk protein denoted RC was investigated using microarray analysis, whereas scFvs fused to the NC silk variant were examined using nanoarrays. Results from micro- and nanoarrays confirmed the functionality of scFvs attached to both RC and NC silk, and also for binding of targets in crude serum. Furthermore, the same amount of added scFv gives higher signal intensity when immobilized via partial spider silk compared to when immobilized alone. Together, the results suggest that usage of scFv-silk fusion proteins in immunoassays could improve target detection, in the long run enabling novel biomarkers to be detected in crude serum proteomes. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Assessment of the Fusion Tags on Increasing Soluble Production of the Active TEV Protease Variant and Other Target Proteins in E. coli.

    Science.gov (United States)

    Yu, Xuelian; Sun, Jiaqi; Wang, Weiyu; Jiang, Li; Cheng, Beijiu; Fan, Jun

    2016-12-17

    In this study, five fusion tags affecting soluble production and cleavage activity of the tobacco etch virus (TEV) protease (TEVp) variant in Escherichia coli strains BL21 (DE3) and Rosetta™ (DE3) are investigated. Combination of the augmenting rare transfer RNAs (tRNAs) and the fused expressivity tag (N-terminal seven amino acid residues of E. coli translation initiation factor II) promotes the soluble TEVp partner expressed at relatively high level. Attachment of the maltose-binding protein (MBP) tag increases soluble expression of the protease released from the fusion protein in E. coli cells, but the incorporated TEVp recognition sequence slightly decreases expressivity of the fusion construct. Except for the green fluorescent protein, the attached expressivity tag shows less efficiency than the MBP tag in enhancing expression levels of the selected five target proteins in the Rosetta™ (DE3) cells under different induction conditions. Our results identified that high-level production of the functional target protein as the fusion partner in E. coli is combined with the intrinsic property of fusion tag, fusion protein stability, inherent folding of target protein, rare tRNA abundance, and the incorporated linker. Purified TEVp fusion constructs with the N-terminal expressivity tag, as well as the MBP partner, are the ideal alternatives for removing fusion tag.

  16. IGF1 is a common target gene of Ewing's sarcoma fusion proteins in mesenchymal progenitor cells.

    Directory of Open Access Journals (Sweden)

    Luisa Cironi

    Full Text Available BACKGROUND: The EWS-FLI-1 fusion protein is associated with 85-90% of Ewing's sarcoma family tumors (ESFT, the remaining 10-15% of cases expressing chimeric genes encoding EWS or FUS fused to one of several ets transcription factor family members, including ERG-1, FEV, ETV1 and ETV6. ESFT are dependent on insulin-like growth factor-1 (IGF-1 for growth and survival and recent evidence suggests that mesenchymal progenitor/stem cells constitute a candidate ESFT origin. METHODOLOGY/PRINCIPAL FINDINGS: To address the functional relatedness between ESFT-associated fusion proteins, we compared mouse progenitor cell (MPC permissiveness for EWS-FLI-1, EWS-ERG and FUS-ERG expression and assessed the corresponding expression profile changes. Whereas all MPC isolates tested could stably express EWS-FLI-1, only some sustained stable EWS-ERG expression and none could express FUS-ERG for more than 3-5 days. Only 14% and 4% of the total number of genes that were respectively induced and repressed in MPCs by the three fusion proteins were shared. However, all three fusion proteins, but neither FLI-1 nor ERG-1 alone, activated the IGF1 promoter and induced IGF1 expression. CONCLUSION/SIGNIFICANCE: Whereas expression of different ESFT-associated fusion proteins may require distinct cellular microenvironments and induce transcriptome changes of limited similarity, IGF1 induction may provide one common mechanism for their implication in ESFT pathogenesis.

  17. The unrecognized contribution of renewable energy to Europe's energy savings target

    NARCIS (Netherlands)

    Harmsen, R.; Wesselink, B.; Eichhammer, W.; Worrell, E.

    2011-01-01

    We show that renewable energy contributes to Europe's 2020 primary energy savings target. This contribution, which is to a large extent still unknown and not recognized by policy makers, results from the way renewable energy is dealt with in Europe's energy statistics. We discuss the policy conseque

  18. The unrecognized contribution of renewable energy to Europe's energy savings target

    NARCIS (Netherlands)

    Harmsen, R.; Wesselink, B.; Eichhammer, W.; Worrell, E.

    2011-01-01

    We show that renewable energy contributes to Europe's 2020 primary energy savings target. This contribution, which is to a large extent still unknown and not recognized by policy makers, results from the way renewable energy is dealt with in Europe's energy statistics. We discuss the policy

  19. Teardrop shapes minimize bending energy of fusion pores connecting planar bilayers

    Science.gov (United States)

    Ryham, Rolf J.; Ward, Mark A.; Cohen, Fredric S.

    2013-12-01

    A numerical gradient flow procedure was devised to characterize minimal energy shapes of fusion pores connecting two parallel planar bilayer membranes. Pore energy, composed of splay, tilt, and stretching, was obtained by modeling each bilayer as two monolayers and treating each monolayer of a bilayer membrane as a freely deformable surface described with a mean lipid orientation field. Voids between the two monolayers were prevented by a steric penalty formulation. Pore shapes were assumed to possess both axial and reflectional symmetry. For fixed pore radius and bilayer separation, the gradient flow procedure was applied to initially toroidal pore shapes. Using initially elliptical pore shapes yielded the same final shape. The resulting minimal pore shapes and energies were analyzed as a function of pore dimension and lipid composition. Previous studies either assumed or confined pore shapes, thereby tacitly supplying an unspecified amount of energy to maintain shape. The shapes derived in the present study were outputs of calculations and an externally provided energy was not supplied. Our procedure therefore yielded energy minima significantly lower than those reported in prior studies. The membrane of minimal energy pores bowed outward near the pore lumen, yielding a pore length that exceeded the distance between the two fusing membranes.

  20. A novel, potentially targetable TMEM106B-BRAF fusion in pleomorphic xanthoastrocytoma

    Science.gov (United States)

    Hsiao, Susan J.; Karajannis, Matthias A.; Diolaiti, Daniel; Mansukhani, Mahesh M.; Bender, Julia Glade; Kung, Andrew L.; Garvin, James H.

    2017-01-01

    Pleomorphic xanthoastrocytoma (PXA) is a World Health Organization (WHO) Grade II glioma occurring primarily in children and young adults. Most PXAs harbor the known activating mutation BRAF V600E. We report a case of locally recurrent PXA with anaplastic features in a 10-yr-old female. The PXA was negative by immunohistochemical (IHC) staining for BRAF V600E mutation. Whole-exome and transcriptome sequencing of the tumor confirmed the absence of BRAF V600E, but identified copy-number alterations (including loss of the tumor suppressor CDKN2A) and a novel TMEM106B-BRAF fusion. Based on similar BRAF fusion proteins, this novel fusion is predicted to result in activation of BRAF signaling. Demonstration of positive IHC for phospho-ERK1/2 and phospho-MEK1/2 supported this prediction, and implicated MEK inhibitors as a potential therapeutic strategy.

  1. Construction of a Novel Liver-Targeting Fusion Interferon by Incorporation of a Plasmodium Region I-Plus Peptide

    Directory of Open Access Journals (Sweden)

    Xuemei Lu

    2014-01-01

    Full Text Available Interferon alpha (IFN α exerts a multiplicity of biological actions including antiviral, immunomodulatory, and antiproliferative effects. Administration of IFN α is the current treatment for chronic hepatitis B; however, therapy outcome has not been completely satisfactory. The systemic effects of IFN α may account for its low in vivo biological activity and multiple adverse events. The purpose of this study was to design a novel liver-targeting fusion interferon (IFN-CSP by fusing IFN α2b with a Plasmodium region I-plus peptide, thus targeting the drug specifically to the liver. The DNA sequence encoding IFN-CSP was constructed using improved splicing by overlapping extension-PCR method, and then cloned into the pET-21b vector for protein expression in E. coli BL21 (DE3. The recombinant protein was expressed as a His-tagged protein and purified using a combination of Ni affinity and HiTrap affinity chromatography at a purity of over 95%. The final yield of biologically active IFN-CSP was up to 270 mg/L culture. The purified recombinant protein showed anti-HBV activity and liver-targeting potentiality in vitro. These data suggests that the novel fusion interferon IFN-CSP may be an excellent candidate as a liver-targeting anti-HBV agent.

  2. A New Target in Non-small Cell Lung Cancer: EML4-ALK Fusion Gene

    Directory of Open Access Journals (Sweden)

    Huijuan WANG

    2011-06-01

    Full Text Available It was only 3 years ago that the fusion gene between echinoderm microtubule-associated protein-like4 (EML4 and anaplastic lymphoma kinase (ALK has been identified in a subset of non-small cell lung cancer (NSCLC. EML4-ALK is most often detected in never smokers with lung adenocarcinoma and has unique pathologic features. EML4-ALK fusion gene is oncogenic, which could be suppressed by ALK-inhibitor through blocking the downstream signaling passway of EML4-ALK. This review will focus on the molecular structure, function, biology, detection method and the diagnostic and therapeutic meaning of EML4-ALK of lung cancer.

  3. Study of fusion Q-value rule in sub-barrier fusion of heavy ions

    Institute of Scientific and Technical Information of China (English)

    LIU Xing-Xing; ZHANG Gao-Long; ZHANG Huan-Qiao

    2015-01-01

    A vast body of fusion data has been analyzed for different projectiles and target nuclei.It is indicated that the sub-barrier fusion depends on the fusion Q-value.In terms of a recently introduced fusion Q-value rule and an energy scaling reduction procedure,the experimental fusion excitation functions are reduced and compared with each other.It is found that the reduced fusion excitations of selected fusion systems show a similar trend.The fusion data for massive nuclei are in agreement with the Q-value rule.In the fusion process,the Q contribution should be considered.Within this approach,the sub-barrier fusion cross sections of most fusion systems can be predicted without involving any structure effects of colliding nuclei.Instances of disagreement are presented in a few fusion systems.The use of the energy scaling as a criterion of possible experimental data inconsistency is discussed.More precise experimental fusion data need to be measured.

  4. Promise and Challenges of SiCf/SiC Composites for Fusion Energy Applications

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Russell H.(BATTELLE (PACIFIC NW LAB)); Giancarli, L. (CEA, Centre d' Etudes de Saclay); Hasegawa, Akira (UNKNOWN); Katoh, Y.; Kohyama, Akira (UNIVERSITY OF TOKYO); Riccardi, B (ENEA-CR Frascati); Snead, Lance L.(UNKNOWN); Weber, William J.(BATTELLE (PACIFIC NW LAB))

    2002-12-30

    Silicon carbide fiber/silicon carbide matrix composites are a promising structural material for fusion energy applications. They have been specified in several recent fusion power plant design studies because of their high operating temperature (1000-1100?C) and hence high energy conversion efficiencies. Radiation resistance of the b-phase of SiC, excellent high-temperature fracture, creep, corrosion and thermal shock resistance and safety advantages arising from low induced radioactivity and afterheat are all positive attributes favoring the selection of SiCf/SiC composites. With the promise of these materials comes a number of challenges such as their thermal conductivity, radiation stability, gaseous transmutation rates, hermetic behavior and joining technology. Recent advances have been made in understanding radiation damage in SiC at the fundamental level through molecular dynamics simulations of displacement cascades. Radiation stability of composites made with the advanced fibers of Nicalon Type S and the UBE Tyranno SA, where no change in strength was observed up to 10 dpa at 800?C, in the development of materials with improved thermal conductivity, modeling of thermal conductivity, joining techniques and models for life-prediction. High transmutation rates of C and Si to form H, He, Mg, and Al continue to be a concern.

  5. Low-energy d+d fusion reactions via the Trojan Horse Method

    Energy Technology Data Exchange (ETDEWEB)

    Tumino, A., E-mail: tumino@lns.infn.it [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy); Universita degli Studi di Enna ' Kore' , Enna (Italy); Spitaleri, C. [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy); Mukhamedzhanov, A.M. [Cyclotron Institute Texas A and M University, College Station, TX (United States); Typel, S. [Excellence Cluster Universe, Technische Universitaet Muenchen, Garching (Germany); GSI Helmholtzzentrum fuer Schwerionenforschung GmbH - Theorie, Darmstadt (Germany); Aliotta, M. [School of Physics and Astronomy, University of Edinburgh, Edinburgh, Scotland (United Kingdom); Scottish Universities Physics Alliance (United Kingdom); Burjan, V. [Nuclear Physics Institute of ASCR, Rez near Prague (Czech Republic); Gimenez del Santo, M. [Departamento de Fisica Nuclear, Universitade de Sao Paulo, Sao Paulo (Brazil); Kiss, G.G. [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy); ATOMKI, Debrecen (Hungary); Kroha, V.; Hons, Z. [Nuclear Physics Institute of ASCR, Rez near Prague (Czech Republic); La Cognata, M.; Lamia, L. [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy); Mrazek, J. [Nuclear Physics Institute of ASCR, Rez near Prague (Czech Republic); Pizzone, R.G. [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy); Piskor, S. [Nuclear Physics Institute of ASCR, Rez (Czech Republic); Rapisarda, G.G.; Romano, S.; Sergi, M.L.; Sparta, R. [Laboratori Nazionali del Sud, INFN, and Dipartimento di Fisica e Astronomia, Universita di Catania, Catania (Italy)

    2011-06-06

    The bare nucleus S(E) factors for the {sup 2}H(d,p){sup 3}H and {sup 2}H(d,n){sup 3}He reactions have been measured for the first time via the Trojan Horse Method off the proton in {sup 3}He from 1.5 MeV down to 2 keV. This range overlaps with the relevant region for Standard Big Bang Nucleosynthesis as well as with the thermal energies of future fusion reactors and deuterium burning in the Pre-Main-Sequence phase of stellar evolution. This is the first pioneering experiment in quasi free regime where the charged spectator is detected. Both the energy dependence and the absolute value of the S(E) factors deviate by more than 15% from available direct data with new S(0) values of 57.4{+-}1.8 MeVb for {sup 3}H+p and 60.1{+-}1.9 MeVb for {sup 3}He+n. None of the existing fitting curves is able to provide the correct slope of the new data in the full range, thus calling for a revision of the theoretical description. This has consequences in the calculation of the reaction rates with more than a 25% increase at the temperatures of future fusion reactors.

  6. Targeting Energy Management : Analysing targets, outcomes and impacts of corporate energy and greenhouse gas management programmes

    NARCIS (Netherlands)

    Rietbergen, M.G.

    2015-01-01

    Global greenhouse gas emissions must be reduced drastically to limit global increases in temperature to the relatively safe level of maximum 2 degrees Celsius. In the coming decades, energy efficiency improvement will be the main strategy for reducing energy-related greenhouse gas emissions. Energy

  7. Why the complete fusion of weakly bond nuclei is enhanced at sub-barrier energies and suppressed above the barrier?

    Energy Technology Data Exchange (ETDEWEB)

    Lubian, J.; Gomes, P.R.S. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil); Canto, L.F. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Hussein, M.S. [Universidade de Sao Paulo (USP), SP (Brazil)

    2012-07-01

    Full text: In the last two decades one has asked whether the complete fusion of weakly bound systems is enhanced or suppressed when compared with the situation where there is no break process. Recent systematic results [1] based on the reduction of cross section and the comparison to the Universal Fusion Function have shown that the complete fusion cross section is indeed enhanced at sub-barrier energies and suppressed at energies above the barrier, when compared with calculations which do not take into account the couplings to breakup channels. In this contribution we discuss and propose a method to explain this conclusion. We point out the importance of direct transfer and breakup processes and also the recently observed sequential breakup that follows the transfer. Different behaviors of the dynamic polarization potentials at different energy regions are used to explain the observed fusion excitation functions for several weakly bound systems. While the breakup polarization is the main reaction channel at above the Coulomb barrier energy regime, leading to repulsive polarization, the sequential breakup (transfer followed by breakup) seems to be the main reaction mechanism at below barrier energies. This last mechanism produces attractive polarization and for this reason it enhances the complete fusion cross section. [1] L.F. Canto et al., Nucl. Phys. A 821, 51 (2009); J. of Phys. G 36, 015109 (2009). (author)

  8. In Silico target fishing: addressing a "Big Data" problem by ligand-based similarity rankings with data fusion.

    Science.gov (United States)

    Liu, Xian; Xu, Yuan; Li, Shanshan; Wang, Yulan; Peng, Jianlong; Luo, Cheng; Luo, Xiaomin; Zheng, Mingyue; Chen, Kaixian; Jiang, Hualiang

    2014-01-01

    Ligand-based in silico target fishing can be used to identify the potential interacting target of bioactive ligands, which is useful for understanding the polypharmacology and safety profile of existing drugs. The underlying principle of the approach is that known bioactive ligands can be used as reference to predict the targets for a new compound. We tested a pipeline enabling large-scale target fishing and drug repositioning, based on simple fingerprint similarity rankings with data fusion. A large library containing 533 drug relevant targets with 179,807 active ligands was compiled, where each target was defined by its ligand set. For a given query molecule, its target profile is generated by similarity searching against the ligand sets assigned to each target, for which individual searches utilizing multiple reference structures are then fused into a single ranking list representing the potential target interaction profile of the query compound. The proposed approach was validated by 10-fold cross validation and two external tests using data from DrugBank and Therapeutic Target Database (TTD). The use of the approach was further demonstrated with some examples concerning the drug repositioning and drug side-effects prediction. The promising results suggest that the proposed method is useful for not only finding promiscuous drugs for their new usages, but also predicting some important toxic liabilities. With the rapid increasing volume and diversity of data concerning drug related targets and their ligands, the simple ligand-based target fishing approach would play an important role in assisting future drug design and discovery.

  9. Prompt photon hadroproduction at high energies in off-shell gluon-gluon fusion

    CERN Document Server

    Baranov, S P; Zotov, N P

    2007-01-01

    The amplitude for production of a single photon associated with quark pair in the fusion of two off-shell gluons is calculated. The matrix element found is applied to the inclusive prompt photon hadroproduction at high energies in the framework of kt-factorization QCD approach. The total and differential cross sections are calculated in both central and forward pseudo-rapidity regions. The conservative error analisys is performed. We used the unintegrated gluon distributions in a proton which were obtained from the full CCFM evolution equation as well as from the Kimber-Martin-Ryskin prescription. Theoretical results were compared with recent experimental data taken by the D0 and CDF collaborations at Fermilab Tevatron. Theoretical predictions for LHC energies are given.

  10. Modeling high-energy radiation damage in nuclear and fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Trachenko, K., E-mail: k.trachenko@qmul.ac.uk [School of Physics, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); School of Physics and Astronomy, University of Southampton Highfield, Southampton SO17 1BJ (United Kingdom); Zarkadoula, E. [School of Physics, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); School of Physics and Astronomy, University of Southampton Highfield, Southampton SO17 1BJ (United Kingdom); Todorov, I.T. [Computational Science and Engineering Department, CCLRC Daresbury Laboratory, Daresbury WA44AD (United Kingdom); Dove, M.T. [School of Physics, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Department of Earth Sciences, University of Cambridge, Downing Street, Cambridge CB2 3EQ (United Kingdom); Dunstan, D.J. [School of Physics, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Nordlund, K. [Accelerator Laboratory, University of Helsinki, P.O. Box 43, FIN-00014 Helsinki (Finland)

    2012-04-15

    We discuss molecular dynamics (MD) simulations of high-energy radiation damage in materials relevant for encapsulation of nuclear waste and materials to be used in fusion reactors, including several important oxides and iron. We study various stages of evolution and relaxation of 100-200 keV collision cascades, and identify reversible elastic and irreversible inelastic structural changes. The elastic expansion of the lattice around the cascade is explained in terms of anharmonicity of interatomic interactions. The remaining irreversible structural change is related to resistance to amorphization by radiation damage. This resistance is quantified by the number of remaining defect atoms in the damaged structure. We discuss how MD simulations can predict experimental resistance to amorphization, including the important case of highly resistant materials. Finally, we discuss our current work to simulate radiation damage of MeV energies and system sizes of the order of billion atoms using massive parallel computing facilities.

  11. An overview on incomplete fusion reaction dynamics at energy range ∼ 3-8 MeV/A

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Rahbar, E-mail: rahbarali1@rediffmail.com [Department of Physics, G. F. (P. G.) College, Shahjahanpur-242001 (India); Singh, D. [Centre for Applied Physics, Central University of Jharkhand, Ranchi-825202 (India); Ansari, M. Afzal [Department of Physics, Aligarh Muslim University, Aligarh-202002 (India); Kumar, Rakesh; Muralithar, S.; Golda, K. S.; Singh, R. P.; Bhowmik, R. K. [Inter University Accelerator Centre, New Delhi-110067 (India); Rashid, M. H.; Guin, R.; Das, S. K. [Variable Energy Cyclotron Centre, Kolkata-700064 (India)

    2014-08-14

    The information of ICF reaction has been obtained from the measurement of excitation function (EF) of ERs populated in the interaction of {sup 20}Ne and {sup 16}O on {sup 55}Mn, {sup 159}Tb and {sup 156}Gd targets. Sizable enhancement in the measured cross-sections has been observed in α-emitting channels over theoretical predictions, which has been attributed to ICF of the projectile. In order to confirm the findings of the measurements and analysis of EFs, the forward recoil range distributions of ERs populated in {sup 20}Ne+{sup 159}Tb (E ∼165MeV) and {sup 16}O+{sup 156}Gd (E ∼ 72, 82 and 93MeV) systems, have been measured. It has been observed that peaks appearing at different cumulative thicknesses in the stopping medium are related with different degree of linear momentum transfer from projectile to target nucleus by adopting the break-up fusion model consideration. In order to deduce the angular momentum involved in various CF and / or ICF reaction products, spin distribution and side-feeding intensity profiles of radio-nuclides populated via CF and ICF channels in {sup 16}O+{sup 160}Gd system at energy, E ∼ 5.6 MeV/A, have been studied. Spin distribution of ICF products are found to be distinctly different than that observed from CF products.

  12. Boron-Proton Nuclear-Fusion Enhancement Induced in Boron-Doped Silicon Targets by Low-Contrast Pulsed Laser

    Directory of Open Access Journals (Sweden)

    A. Picciotto

    2014-08-01

    Full Text Available We show that a spatially well-defined layer of boron dopants in a hydrogen-enriched silicon target allows the production of a high yield of alpha particles of around 10^{9} per steradian using a nanosecond, low-contrast laser pulse with a nominal intensity of approximately 3×10^{16}  W cm^{−2}. This result can be ascribed to the nature of the long laser-pulse interaction with the target and with the expanding plasma, as well as to the optimal target geometry and composition. The possibility of an impact on future applications such as nuclear fusion without production of neutron-induced radioactivity and compact ion accelerators is anticipated.

  13. The Complete Burning of Weapons Grade Plutonium and Highly Enriched Uranium with (Laser Inertial Fusion-Fission Energy) LIFE Engine

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, J C; Diaz de la Rubia, T; Moses, E

    2008-12-23

    The National Ignition Facility (NIF) project, a laser-based Inertial Confinement Fusion (ICF) experiment designed to achieve thermonuclear fusion ignition and burn in the laboratory, is under construction at the Lawrence Livermore National Laboratory (LLNL) and will be completed in April of 2009. Experiments designed to accomplish the NIF's goal will commence in late FY2010 utilizing laser energies of 1 to 1.3 MJ. Fusion yields of the order of 10 to 20 MJ are expected soon thereafter. Laser initiated fusion-fission (LIFE) engines have now been designed to produce nuclear power from natural or depleted uranium without isotopic enrichment, and from spent nuclear fuel from light water reactors without chemical separation into weapons-attractive actinide streams. A point-source of high-energy neutrons produced by laser-generated, thermonuclear fusion within a target is used to achieve ultra-deep burn-up of the fertile or fissile fuel in a sub-critical fission blanket. Fertile fuels including depleted uranium (DU), natural uranium (NatU), spent nuclear fuel (SNF), and thorium (Th) can be used. Fissile fuels such as low-enrichment uranium (LEU), excess weapons plutonium (WG-Pu), and excess highly-enriched uranium (HEU) may be used as well. Based upon preliminary analyses, it is believed that LIFE could help meet worldwide electricity needs in a safe and sustainable manner, while drastically shrinking the nation's and world's stockpile of spent nuclear fuel and excess weapons materials. LIFE takes advantage of the significant advances in laser-based inertial confinement fusion that are taking place at the NIF at LLNL where it is expected that thermonuclear ignition will be achieved in the 2010-2011 timeframe. Starting from as little as 300 to 500 MW of fusion power, a single LIFE engine will be able to generate 2000 to 3000 MWt in steady state for periods of years to decades, depending on the nuclear fuel and engine configuration. Because the fission

  14. Thermodynamic free-energy minimization for unsupervised fusion of dual-color infrared breast images

    Science.gov (United States)

    Szu, Harold; Miao, Lidan; Qi, Hairong

    2006-04-01

    function [A] may vary from the point tumor to its neighborhood, we could not rely on neighborhood statistics as did in a popular unsupervised independent component analysis (ICA) mathematical statistical method, we instead impose the physics equilibrium condition of the minimum of Helmholtz free-energy, H = E - T °S. In case of the point breast cancer, we can assume the constant ground state energy E ° to be normalized by those benign neighborhood tissue, and then the excited state can be computed by means of Taylor series expansion in terms of the pixel I/O data. We can augment the X-ray mammogram technique with passive IR imaging to reduce the unwanted X-rays during the chemotherapy recovery. When the sequence is animated into a movie, and the recovery dynamics is played backward in time, the movie simulates the cameras' potential for early detection without suffering the PD=0.1 search uncertainty. In summary, we applied two satellite-grade dual-color IR imaging cameras and advanced military (automatic target recognition) ATR spectrum fusion algorithm at the middle wavelength IR (3 - 5μm) and long wavelength IR (8 - 12μm), which are capable to screen malignant tumors proved by the time-reverse fashion of the animated movie experiments. On the contrary, the traditional thermal breast scanning/imaging, known as thermograms over decades, was IR spectrum-blind, and limited to a single night-vision camera and the necessary waiting for the cool down period for taking a second look for change detection suffers too many environmental and personnel variabilities.

  15. Adaptive Energy-Efficient Target Detection Based on Mobile Wireless Sensor Networks.

    Science.gov (United States)

    Zou, Tengyue; Li, Zhenjia; Li, Shuyuan; Lin, Shouying

    2017-05-04

    Target detection is a widely used application for area surveillance, elder care, and fire alarms; its purpose is to find a particular object or event in a region of interest. Usually, fixed observing stations or static sensor nodes are arranged uniformly in the field. However, each part of the field has a different probability of being intruded upon; if an object suddenly enters an area with few guardian devices, a loss of detection will occur, and the stations in the safe areas will waste their energy for a long time without any discovery. Thus, mobile wireless sensor networks may benefit from adaptation and pertinence in detection. Sensor nodes equipped with wheels are able to move towards the risk area via an adaptive learning procedure based on Bayesian networks. Furthermore, a clustering algorithm based on k-means++ and an energy control mechanism is used to reduce the energy consumption of nodes. The extended Kalman filter and a voting data fusion method are employed to raise the localization accuracy of the target. The simulation and experimental results indicate that this new system with adaptive energy-efficient methods is able to achieve better performance than the traditional ones.

  16. Fusion Energy Sciences Advisory Committee Reports on Review of the Fusion Materials Research Program, Review of the Proposed Proof-of-Principle Programs, Review of the Possible Pathways for Pursuing Burning Plasma Physics, and Comments on the ER Facilities Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1998-07-01

    The Fusion Energy Science Advisory Committee was asked to conduct a review of Fusion Materials Research Program (the Structural Materials portion of the Fusion Program) by Dr. Martha Krebs, Director of Energy Research for the Department of Energy. This request was motivated by the fact that significant changes have been made in the overall direction of the Fusion Program from one primarily focused on the milestones necessary to the construction of successively larger machines to one where the necessary scientific basis for an attractive fusion energy system is. better understood. It was in this context that the review of current scientific excellence and recommendations for future goals and balance within the Program was requested.

  17. Cytolethal distending toxin B as a cell-killing component of tumor-targeted anthrax toxin fusion proteins.

    Science.gov (United States)

    Bachran, C; Hasikova, R; Leysath, C E; Sastalla, I; Zhang, Y; Fattah, R J; Liu, S; Leppla, S H

    2014-01-16

    Cytolethal distending toxin (Cdt) is produced by Gram-negative bacteria of several species. It is composed of three subunits, CdtA, CdtB, and CdtC, with CdtB being the catalytic subunit. We fused CdtB from Haemophilus ducreyi to the N-terminal 255 amino acids of Bacillus anthracis toxin lethal factor (LFn) to design a novel, potentially potent antitumor drug. As a result of this fusion, CdtB was transported into the cytosol of targeted cells via the efficient delivery mechanism of anthrax toxin. The fusion protein efficiently killed various human tumor cell lines by first inducing a complete cell cycle arrest in the G2/M phase, followed by induction of apoptosis. The fusion protein showed very low toxicity in mouse experiments and impressive antitumor effects in a Lewis Lung carcinoma model, with a 90% cure rate. This study demonstrates that efficient drug delivery by a modified anthrax toxin system combined with the enzymatic activity of CdtB has great potential as anticancer treatment and should be considered for the development of novel anticancer drugs.

  18. Fusion power in a future low carbon global electricity system

    DEFF Research Database (Denmark)

    Cabal, H.; Lechón, Y.; Bustreo, C.

    2017-01-01

    Fusion is one of the technologies that may contribute to a future, low carbon, global energy supply system. In this article we investigate the role that it may play under different scenarios. The global energy model ETM (originally EFDA TIMES Model) has been used to analyse the participation...... of fusion technologies in the global electricity system in the long term. Results show that fusion technologies penetration is higher in scenarios with stricter CO2 emissions reduction targets. In addition, investment costs and discount rates of fusion technologies are key factors for fusion implementation...

  19. Beamed Energy Propulsion by Means of Target Ablation

    Science.gov (United States)

    Rosenberg, Benjamin A.

    2004-03-01

    This paper describes hundreds of pendulum tests examining the beamed energy conversion efficiency of different metal targets coated with multiple liquid enhancers. Preliminary testing used a local laser with photographic paper targets, with no liquid, water, canola oil, or methanol additives. Laboratory experimentation was completed at Wright-Patterson AFB using a high-powered laser, and ballistic pendulums of aluminum, titanium, or copper. Dry targets, and those coated with water, methanol and oil were repeatedly tested in laboratory conditions. Results were recorded on several high-speed digital video cameras, and the conversion efficiency was calculated. Paper airplanes successfully launched using BEP were likewise recorded.

  20. MONTE CARLO MODEL FOR NEUTRON PRODUCTION BY THE INTERACTIONS OF LOW ENERGY DEUTERONS IN SOLID TARGETS

    OpenAIRE

    Milocco, Alberto

    2012-01-01

    The construction of the nuclear fusion plant 'ITER' has started in 2009 at Cadarache, France. The ITER machine represents a milestone in the civil use of the nuclear fusion energy. The physics of ITER is based on the fusion reaction between deuteron and triton nuclei (d-t). The deuteron-deuteron reaction (d-d) is also interesting and is foreseen for the next generation of fusion reactors. The experimental activities carried out in the context of the ITER neutronics involve intense fields of n...

  1. An Artificial Measurements-Based Adaptive Filter for Energy-Efficient Target Tracking via Underwater Wireless Sensor Networks.

    Science.gov (United States)

    Chen, Huayan; Zhang, Senlin; Liu, Meiqin; Zhang, Qunfei

    2017-04-27

    We study the problem of energy-efficient target tracking in underwater wireless sensor networks (UWSNs). Since sensors of UWSNs are battery-powered, it is impracticable to replace the batteries when exhausted. This means that the battery life affects the lifetime of the whole network. In order to extend the network lifetime, it is worth reducing the energy consumption on the premise of sufficient tracking accuracy. This paper proposes an energy-efficient filter that implements the tradeoff between communication cost and tracking accuracy. Under the distributed fusion framework, local sensors should not send their weak information to the fusion center if their measurement residuals are smaller than the pre-given threshold. In order to guarantee the target tracking accuracy, artificial measurements are generated to compensate for those unsent real measurements. Then, an adaptive scheme is derived to take full advantages of the artificial measurements-based filter in terms of energy-efficiency. Furthermore, a computationally efficient optimal sensor selection scheme is proposed to improve tracking accuracy on the premise of employing the same number of sensors. Simulation demonstrates that our scheme has superior advantages in the tradeoff between communication cost and tracking accuracy. It saves much energy while loosing little tracking accuracy or improves tracking performance with less additional energy cost.

  2. Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, J. [ed.

    1998-12-01

    During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ``On-site Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks.

  3. Survey of Laser Markets Relevant to Inertial Fusion Energy Drivers, information for National Research Council

    Energy Technology Data Exchange (ETDEWEB)

    Bayramian, A J; Deri, R J; Erlandson, A C

    2011-02-24

    Development of a new technology for commercial application can be significantly accelerated by leveraging related technologies used in other markets. Synergies across multiple application domains attract research and development (R and D) talent - widening the innovation pipeline - and increases the market demand in common components and subsystems to provide performance improvements and cost reductions. For these reasons, driver development plans for inertial fusion energy (IFE) should consider the non-fusion technology base that can be lveraged for application to IFE. At this time, two laser driver technologies are being proposed for IFE: solid-state lasers (SSLs) and KrF gas (excimer) lasers. This document provides a brief survey of organizations actively engaged in these technologies. This is intended to facilitate comparison of the opportunities for leveraging the larger technical community for IFE laser driver development. They have included tables that summarize the commercial organizations selling solid-state and KrF lasers, and a brief summary of organizations actively engaged in R and D on these technologies.

  4. EURATOM-CEA association contributions to the 18. IAEA fusion energy conference

    Energy Technology Data Exchange (ETDEWEB)

    Ghendrih, Ph.; Peysson, Y.; Hoang, G.T. [and others

    2000-12-01

    The 9 contributions of EURATOM-Cea association to the fusion energy conference hold at Sorrento are gathered in this document with 7 additional papers. The different titles are: 1) Ergodic divertor experiments on the route to steady state operation of Tore-Supra, 2) High power lower hybrid current drive experiments in Tore-Supra tokamak, 3) Electron transport and improved confinement on Tore-Supra, 4) ECRH experiments and developments for long pulse in Tore-Supra, 5) Impurity penetration and contamination in Tore-Supra ergodic divertor experiments, 6) Real time plasma feed-back control: an overview of Tore-Supra achievements, 7) Numerical assessment of the ion turbulent thermal transport scaling laws, 8) Design of next step tokamak: consistent analysis of plasma flux consumption and poloidal, 9) Large superconducting conductors and joints for fusion magnets: from conceptual design to test at full size scale, 10) Burst-prone transport in tokamaks with internal transport barriers, 11) Electrostatic turbulence with finite parallel correlation length and radial electric field generation, 12) Theoretical issues in tokamak confinement: internal-edge transport barriers and runaway avalanche confinement, 13) Core and edge confinement studies with different heating methods in JET, 14) Confinement and transport studies of conventional scenarios in ASDEX upgrade, 15) First test results for the ITER central solenoid model coil, and 16) Progress of the ITER central solenoid model coil program.

  5. High energy resummation of transverse momentum distributions:Higgs in gluon fusion

    CERN Document Server

    Forte, Stefano

    2015-01-01

    We derive a general resummation formula for transverse-momentum distributions of hard processes at the leading logarithmic level in the high-energy limit, to all orders in the strong coupling. Our result is based on a suitable generalization of high-energy factorization theorems, whereby all-order resummation is reduced to the determination of the Born-level process but with incoming off-shell gluons. We validate our formula by applying it to Higgs production in gluon fusion in the infinite top mass limit. We check our result up to next-to-leading order by comparison to the high energy limit of the exact expression and to next-to-next-to leading by comparison to NNLL order trasverse momentum (Sudakov) resummation, and we predict the high-energy behaviour at next$^3$-to-leading order. We also show that the structure of the result in the small transverse momentum limit agrees to all orders with general constraints from Sudakov resummation.

  6. Online energy management strategy of fuel cell hybrid electric vehicles based on data fusion approach

    Science.gov (United States)

    Zhou, Daming; Al-Durra, Ahmed; Gao, Fei; Ravey, Alexandre; Matraji, Imad; Godoy Simões, Marcelo

    2017-10-01

    Energy management strategy plays a key role for Fuel Cell Hybrid Electric Vehicles (FCHEVs), it directly affects the efficiency and performance of energy storages in FCHEVs. For example, by using a suitable energy distribution controller, the fuel cell system can be maintained in a high efficiency region and thus saving hydrogen consumption. In this paper, an energy management strategy for online driving cycles is proposed based on a combination of the parameters from three offline optimized fuzzy logic controllers using data fusion approach. The fuzzy logic controllers are respectively optimized for three typical driving scenarios: highway, suburban and city in offline. To classify patterns of online driving cycles, a Probabilistic Support Vector Machine (PSVM) is used to provide probabilistic classification results. Based on the classification results of the online driving cycle, the parameters of each offline optimized fuzzy logic controllers are then fused using Dempster-Shafer (DS) evidence theory, in order to calculate the final parameters for the online fuzzy logic controller. Three experimental validations using Hardware-In-the-Loop (HIL) platform with different-sized FCHEVs have been performed. Experimental comparison results show that, the proposed PSVM-DS based online controller can achieve a relatively stable operation and a higher efficiency of fuel cell system in real driving cycles.

  7. Targets IMage Energy Regional (TIMER) Model, Technical Documentation

    NARCIS (Netherlands)

    Vries B de; Vuuren D van; Elzen M den; Janssen M; MNV

    2002-01-01

    Er wordt een gedetailleerde beschrijving gegeven van het Targets IMage Energy Regional (TIMER) simulatiemodel. Het model is ontwikkeld en toegepast in nauwe relatie met het Integrated Model to Assess the Global Environment (IMAGE) 2.1-2.2. . Het TIMER model is een systeem-dynamisch simulatiemode

  8. High energy physics with polarized beams and targets. [65 papers

    Energy Technology Data Exchange (ETDEWEB)

    Marshak, M L [ed.

    1976-01-01

    Sixty-six papers are presented as a report on conference sessions held from August 23-27, 1976, at Argonne National Laboratory. Topics covered include: (1) strong interactions; (2) weak and electromagnetic interactions; (3) polarized beams; and (4) polarized targets. A separate abstract was prepared for each paper for ERDA Energy Research Abstracts (ERA) and for the INIS Atomindex. (PMA)

  9. Targets IMage Energy Regional (TIMER) Model, Technical Documentation

    NARCIS (Netherlands)

    Vries B de; Vuuren D van; Elzen M den; Janssen M; MNV

    2002-01-01

    Er wordt een gedetailleerde beschrijving gegeven van het Targets IMage Energy Regional (TIMER) simulatiemodel. Het model is ontwikkeld en toegepast in nauwe relatie met het Integrated Model to Assess the Global Environment (IMAGE) 2.1-2.2. . Het TIMER model is een systeem-dynamisch

  10. Targeting Energy Metabolic Pathways as Therapeutic Intervention for Breast Cancer

    Science.gov (United States)

    2014-12-01

    observed that the cells with knockdown of eEF-2K expression exhibited a decreased glucose consumption (Fig. 1B), as measured by flow cytometric analysis of......3. DATES COVERED 30 Sep 2011 - 20 Sep 2014 4. TITLE AND SUBTITLE 5a. CONTRACT NUMBER Targeting Energy Metabolic Pathways as Therapeutic

  11. Contemporary Targets for Control of Efficient Energy Use

    Directory of Open Access Journals (Sweden)

    Yu. Petrusha

    2012-01-01

    Full Text Available The paper describes main principles of the methodology for control of efficient energy use in power engineering and economy sectors as a whole. Targets for control of energy use at different levels have been considered in the paper. A special attention has been paid to technical, organizational and legal aspects of energy efficiency improvement. The paper contains an analysis of the history of the given issue, the present level of its development and near-term prospects under conditions of the Republic of Belarus.

  12. The Equilibrium and Pre-equilibrium Triton Emission Spectra of Some Target Nuclei for ( n, xt) Reactions up to 45 MeV Energy

    Science.gov (United States)

    Tel, E.; Kaplan, A.; Aydın, A.; Özkorucuklu, S.; Büyükuslu, H.; Yıldırım, G.

    2010-08-01

    Although there have been significant research and development studies on the inertial and magnetic fusion reactor technology, there is still a long way to go to penetrate commercial fusion reactors to the energy market. Tritium self-sufficiency must be maintained for a commercial power plant. For self-sustaining (D-T) fusion driver tritium breeding ratio should be greater than 1.05. So, working out the systematics of ( n,t) reaction cross sections and triton emission differential data are important for the given reaction taking place on various nuclei at different energies. In this study, ( n,xt) reactions for some target nuclei as 16O, 27Al, 59Co and 209Bi have been investigated up to 45 MeV incident neutron energy. In the calculations of the triton emission spectra, the pre-equilibrium and equilibrium effects have been used. The calculated results have been compared with the experimental data taken from the literature.

  13. Fusion Energy Division annual progress report, period ending December 31, 1988

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, J.; Berry, L.A.; Saltmarsh, M.J.

    1990-02-01

    This report discusses the following topics on fusion research: toroidal confinement activities; atomic physics and plasma diagnostics development; fusion theory and computation; plasma technology; superconducting magnet development; advanced systems program; fusion materials research; neutron transport; and management services, quality assurance, and safety.

  14. European roadmap to the realization of fusion energy: Mission for solution on heat-exhaust systems

    NARCIS (Netherlands)

    Turnyanskiy, M.; Neu, R.; Albanese, R.; Ambrosino, R.; Bachmann, C.; Brezinsek, S.; Donne, A. J. H.; Eich, T.; Falchetto, G.; G Federici,; Kalupin, D.; Litaudon, X.; Mayoral, M.; McDonald, D. C.; Reimerdes, H.; Romanelli, F.; Wenninger, R.; You, J. H.

    2015-01-01

    Horizon 2020 is the largest EU Research and Innovation programme to date. The European fusion research programme for Horizon 2020 is outlined in the “Roadmap to the realization of fusion energy” and published in 2012 [1]. As part of it, the European Fusion Consortium (EUROfusion) has been establishe

  15. Reaction-Based SiC Materials for Joining Silicon Carbide Composites for Fusion Energy

    Energy Technology Data Exchange (ETDEWEB)

    Lewinsohn, Charles A.; Jones, Russell H.; Singh, M.; Serizawa, H.; Katoh, Y.; Kohyama, A.

    2000-09-01

    The fabrication of large or complex silicon carbide-fiber-reinforced silicon carbide (SiC/SiC) components for fusion energy systems requires a method to assemble smaller components that are limited in size by manufacturing constraints. Previous analysis indicates that silicon carbide should be considered as candidate joint materials. Two methods to obtain SiC joints rely on a reaction between silicon and carbon to produce silicon carbide. This report summarizes preliminary mechanical properties of joints formed by these two methods. The methods appear to provide similar mechanical properties. Both the test methods and materials are preliminary in design and require further optimization. In an effort to determine how the mechanical test data is influenced by the test methodology and specimen size, plans for detailed finite element modeling (FEM) are presented.

  16. The status of Fast Ignition Realization Experiment (FIREX) and prospects for inertial fusion energy

    Science.gov (United States)

    Azechi, H.; FIREX Project Team

    2016-05-01

    Here we report recent progress for the fast ignition inertial confinement fusion demonstration. The fraction of low energy (heats the fuel core, increases by a factor of 4 by enhancing pulse contrast of heating laser and removing preformed plasma sources. Kilo-tesla magnetic field is studied to guide the diverging REB to the fuel core. The transport simulation of the REB accelerated by the heating laser in the externally applied and compressed magnetic field indicates that the REB can be guided efficiently to the fuel core. The integrated simulation shows > 4% of the heating efficiency and > 4 keV of ion temperature are achievable by using GEKKO-XII and LFEX, properly designed cone-fuel and an external magnetic field.

  17. Comparative analysis of anodized, implanted and sputtered tantalum oxide targets for the study of {sup 16}O+{sup 16}O fusion reaction

    Energy Technology Data Exchange (ETDEWEB)

    Silva, H., E-mail: hugo_miguel_m_silva@hotmail.com [Departamento de Física, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Centro de Física Nuclear da Universidade de Lisboa, Av. Prof. Gama Pinto, 1649-003 Lisboa (Portugal); Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Cruz, J. [Departamento de Física, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Centro de Física Nuclear da Universidade de Lisboa, Av. Prof. Gama Pinto, 1649-003 Lisboa (Portugal); Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Redondo-Cubero, A. [Instituto Superior Técnico, Campus Tecnológico e Nuclear, Universidade Técnica de Lisboa, Estrada Nacional 10, 2686-953 Sacavém (Portugal); and others

    2014-07-15

    Measuring the total cross section of a fusion reaction in the region of astrophysical interest, such as the {sup 16}O+{sup 16}O fusion reaction, is a real challenge due the very small cross sections involved and the large number of possible exit channels. Taking into account these difficulties, the use of targets with known thickness, stoichiometry and minimal contamination that can withstand high beam currents is required. In this study, we report the comparison between three different types of targets for the study of this fusion reaction, such as anodized, implanted and sputtered tantalum oxide targets and the results show that the anodized and sputtered targets are more suitable for this study due to their higher oxygen density and to the formation of a stable oxide compound, tantalum pentoxide (Ta{sub 2}O{sub 5})

  18. Introduction of American Laser Inertial Fusion Energy%美国激光惯性约束聚变能源研究综述

    Institute of Scientific and Technical Information of China (English)

    刘成安; 师学明

    2013-01-01

    简要地介绍了美国激光惯性约束聚变能源(LIFE)的研究现状与发展前景.基于美国国家点火装置(NIF)的近期进展,美国利弗莫尔实验室提出了激光惯性约束聚变能源设想,并开始了分解研究.设想用新型二极管泵浦固体激光器产生1.4~2.0 MJ的激光能量,靶丸聚变增益25~30,打靶频率10~15Hz,实现350~500 MW聚变功率,相当于聚变中子源强1.3×1020~1.8×1020 n/s.以此驱动次临界裂变包层,使能量再倍增4~10倍,实现1 GW电功率的输出.采用创新设计的燃料元件,包层可达到90%以上的燃耗深度,形成一个安全、无碳、燃料资源丰富、核废料少、可持续发展的新型核能源系统.%In this paper the present study situation and prospect of the American laser-based Inertial Confinement Fusion Energy (LIFE) are briefly introduced. It is based on recent progress of National Inertial Facility (NIF) and related research have begun. On the assumption of using laser energy of 1.4 to 2.0 MJ, the target fusion gain G=25~30, the repetition rate 10 to 15 Hz, the fusion power of 350 to 500 MW or neutron source power of 1.3×1020 to 1.8×l020 n/s could be achieved. For a sub-critical fission blanket driven by this fusion neutrons power, energy multiplication M of 4~10 and several GW of thermal power could be obtained. By novel design on fuel pins, burnup more than 90% would be achieved for heavy metals in the blanket. Inertial Confinement Fusion-fission energy is a promising concept, which characterized by inherent safety, richness in nuclear fuel resources, minimization of nuclear waste, non-CO2 emitting , and it is a sustainable energy source.

  19. Visualizing fast electron energy transport into laser-compressed high-density fast-ignition targets

    Science.gov (United States)

    Jarrott, L. C.; Wei, M. S.; McGuffey, C.; Solodov, A. A.; Theobald, W.; Qiao, B.; Stoeckl, C.; Betti, R.; Chen, H.; Delettrez, J.; Döppner, T.; Giraldez, E. M.; Glebov, V. Y.; Habara, H.; Iwawaki, T.; Key, M. H.; Luo, R. W.; Marshall, F. J.; McLean, H. S.; Mileham, C.; Patel, P. K.; Santos, J. J.; Sawada, H.; Stephens, R. B.; Yabuuchi, T.; Beg, F. N.

    2016-05-01

    Recent progress in kilojoule-scale high-intensity lasers has opened up new areas of research in radiography, laboratory astrophysics, high-energy-density physics, and fast-ignition (FI) laser fusion. FI requires efficient heating of pre-compressed high-density fuel by an intense relativistic electron beam produced from laser-matter interaction. Understanding the details of electron beam generation and transport is crucial for FI. Here we report on the first visualization of fast electron spatial energy deposition in a laser-compressed cone-in-shell FI target, facilitated by doping the shell with copper and imaging the K-shell radiation. Multi-scale simulations accompanying the experiments clearly show the location of fast electrons and reveal key parameters affecting energy coupling. The approach provides a more direct way to infer energy coupling and guide experimental designs that significantly improve the laser-to-core coupling to 7%. Our findings lay the groundwork for further improving efficiency, with 15% energy coupling predicted in FI experiments using an existing megajoule-scale laser driver.

  20. Considerations of the high magnetic field tokamak path on the approach to fusion energy

    Science.gov (United States)

    Marmar, Earl

    2015-11-01

    This tutorial will review the physics basis, and its applications, for high magnetic field, compact visions of steady-state pilot plants and fusion reactors. This includes: energy and particle confinement; transport barriers; heating and current drive; scrape-off layer and divertor physics including implications for power handling, and ash/impurity control. The development of new technologies, particularly high-temperature, high critical magnetic field superconducting materials opens a new opportunity to consider the leverage of on-axis magnetic fields of 10T or more, enabling the feasibility of smaller sized devices on the path to fusion energy, including a pilot plant which could produce hundreds of megawatts of net electricity in a 10T tokamak with major radius of order 3 meter. Incorporating jointed magnetic coils, also made feasible by the high temperature superconductors, can dramatically improve flexibility of experimental superconducting facilities, and ultimately maintainability for reactor systems. Steady-state requires high bootstrap fraction, combined with efficient off-axis current drive, and existing and new approaches for RF sustainment will be covered, including Lower Hybrid Current Drive (both from the low- and high-field side), ECCD, and fast-wave techniques. External torque drive from neutral beams, routinely used in most present-day experiments to enhance confinement and suppress instabilities, will be weak or absent in reactors. Alternative, RF-based flow drive, using mode-converted ICRF waves will be discussed. All reactor concepts have extraordinary power handling requirements, combined with stringent limits on PFC erosion and impurity sources; the current state of the art in divertor configurations will be compared with emerging and new concepts, including snowflake, x-point, x-divertor and liquid metals, to meet these challenges. Supported by USDOE.

  1. Advances in HYDRA and its applications to simulations of inertial confinement fusion targets

    Directory of Open Access Journals (Sweden)

    Marinak M.M.

    2013-11-01

    Full Text Available A new set of capabilities has been implemented in the HYDRA 2D/3D multiphysics inertial confinement fusion simulation code. These include a Monte Carlo particle transport library. It models transport of neutrons, gamma rays and light ions, as well as products they generate from nuclear and coulomb collisions. It allows accurate simulations of nuclear diagnostic signatures from capsule implosions. We apply it to here in a 3D simulation of a National Ignition Facility (NIF ignition capsule which models the full capsule solid angle. This simulation contains a severely rough ablator perturbation and provides diagnostics signatures of capsule failure due to excessive instability growth.

  2. Discovery of HIV fusion inhibitors targeting gp41 using a comprehensive α-helix mimetic library

    Science.gov (United States)

    Whitby, Landon R.; Boyle, Kristopher E.; Cai, Lifeng; Yu, Xiaoqian; Gochin, Miriam; Boger, Dale L.

    2012-01-01

    The evaluation of a comprehensive α-helix mimetic library for binding the gp41 NHR hydrophobic pocket recognizing an intramolecular CHR α-helix provided a detailed depiction of structural features required for binding and led to the discovery of small molecule inhibitors (Ki 0.6–1.3 µM) that not only match or exceed the potency of those disclosed over the past decade, but that also exhibit effective activity in a cell–cell fusion assay (IC50 5–8 µM). PMID:22424973

  3. Economics and Environmental Compatibility of Fusion Reactors —Its Analysis and Coming Issues— 4.Economic Effect of Fusion in Energy Market 4.2Various Externalities of Energy Systems and the Integrated Evaluation

    Science.gov (United States)

    Ito, Keishiro

    The primacy of a nuclear fusion reactor in a competitive energy market remarkably depends on to what extent the reactor contributes to reduce the externalities of energy. The reduction effects are classified into two effects, which have quite dissimilar characteristics. One is an effect of environmental dimensions. The other is related to energy security. In this study I took up the results of EC's Extern Eproject studies as are presentative example of the former effect. Concerning the latter effect, I clarified the fundamental characteristics of externalities related to energy security and the conceptual framework for the purpose of evaluation. In the socio-economical evaluation of research into and development investments in nuclear fusions reactors, the public will require the development of integrated evaluation systems to support the cost-effect analysis of how well the reduction effects of externalities have been integrated with the effects of technological innovation, learning, spillover, etc.

  4. High-power-density approaches to magnetic fusion energy: Problems and promise of compact reversed-field pinch reactors (CRFPR)

    Science.gov (United States)

    Hagenson, Randy L.; Krakowski, Robert A.; Dreicer, Harry

    1983-03-01

    If the costing assumptions upon which the positive assessment of conventional large superconducting fusion reactors are based proves overly optimistic, approaches that promise considerably increased system power density and reduced mass utilization will be required. These more compact reactor embodiments generally must operate with reduced shield thickness and resistive magnets. Because of the unique magnetic topology associated with the Reversed-Field Pinch (RFP), the compact reactor embodiment for this approach is particularly attractive from the viewpoint of low-field resistive coils operating with ohmic losses that can be made small relative to the fusion power. The RFP, therefore, is used as one example of a high-power-density (HPD) approach to magnetic fusion energy. A comprehensive system model is described and applied to select a unique, cost-optimized design point that will be used for a subsequent conceptual engineering design of the compact RFP Reactor (CRFPR). This cost-optimized CRFPR design serves as an example of a HPD fusion reactor that would operate with system power densities and mass utilizations that are comparable to fission power plants, these measures of system performance being an order of magnitude more favorable than the conventional approaches to magnetic fusion energy (MFE).

  5. Development of next generation tempered and ODS reduced activation ferritic/martensitic steels for fusion energy applications

    Science.gov (United States)

    Zinkle, S. J.; Boutard, J. L.; Hoelzer, D. T.; Kimura, A.; Lindau, R.; Odette, G. R.; Rieth, M.; Tan, L.; Tanigawa, H.

    2017-09-01

    Reduced activation ferritic/martensitic steels are currently the most technologically mature option for the structural material of proposed fusion energy reactors. Advanced next-generation higher performance steels offer the opportunity for improvements in fusion reactor operational lifetime and reliability, superior neutron radiation damage resistance, higher thermodynamic efficiency, and reduced construction costs. The two main strategies for developing improved steels for fusion energy applications are based on (1) an evolutionary pathway using computational thermodynamics modelling and modified thermomechanical treatments (TMT) to produce higher performance reduced activation ferritic/martensitic (RAFM) steels and (2) a higher risk, potentially higher payoff approach based on powder metallurgy techniques to produce very high strength oxide dispersion strengthened (ODS) steels capable of operation to very high temperatures and with potentially very high resistance to fusion neutron-induced property degradation. The current development status of these next-generation high performance steels is summarized, and research and development challenges for the successful development of these materials are outlined. Material properties including temperature-dependent uniaxial yield strengths, tensile elongations, high-temperature thermal creep, Charpy impact ductile to brittle transient temperature (DBTT) and fracture toughness behaviour, and neutron irradiation-induced low-temperature hardening and embrittlement and intermediate-temperature volumetric void swelling (including effects associated with fusion-relevant helium and hydrogen generation) are described for research heats of the new steels.

  6. Deployment of membrane fusion protein domains during fusion.

    Science.gov (United States)

    Bentz, J; Mittal, A

    2000-01-01

    It is clear that both viral and intracellular membrane fusion proteins contain a minimal set of domains which must be deployed at the appropriate time during the fusion process. An account of these domains and their functions is given here for the four best-described fusion systems: influenza HA, sendai virus F1, HIV gp120/41 and the neuronal SNARE core composed of synaptobrevin (syn), syntaxin (stx) and the N- and C-termini of SNAP25 (sn25), together with the Ca(2+)binding protein synaptotagmin (syt). Membrane fusion begins with the binding of the virion or vesicle to the target membrane via receptors. The committed step in influenza HA- mediated fusion begins with an aggregate of HAs (at least eight) with some of their HA2 N-termini, a.k.a. fusion peptides, embedded into the viral bilayer (Bentz, 2000 a). The hypothesis presented in Bentz (2000 b) is that the conformational change of HA to the extended coiled coil extracts the fusion peptides from the viral bilayer. When this extraction occurs from the center of the site of restricted lipid flow, it exposes acyl chains and parts of the HA transmembrane domains to the aqueous media, i.e. a hydrophobic defect is formed. This is the 'transition state' of the committed step of fusion. It is stabilized by a 'dam' of HAs, which are inhibited from diffusing away by the rest of the HAs in the aggregate and because that would initially expose more acyl chains to water. Recruitment of lipids from the apposed target membrane can heal this hydrophobic defect, initiating lipid mixing and fusion. The HA transmembrane domains are required to be part of the hydrophobic defect, because the HA aggregate must be closely packed enough to restrict lipid flow. This hypothesis provides a simple and direct coupling between the energy rel