WorldWideScience

Sample records for full vectorial analysis

  1. Full-vectorial analysis of optical waveguides by the finite difference method based on polynomial interpolation

    Institute of Scientific and Technical Information of China (English)

    Xiao Jin-Biao; Zhang Ming-De; Sun Xiao-Han

    2006-01-01

    Based on the polynomial interpolation, a new finite difference (FD) method in solving the full-vectorial guidedmodes for step-index optical waveguides is proposed. The discontinuities of the normal components of the electric field across abrupt dielectric interfaces are considered in the absence of the limitations of scalar and semivectorial approximation, and the present FD scheme can be applied to both uniform and non-uniform mesh grids. The modal propagation constants and field distributions for buried rectangular waveguides and optical rib waveguides are presented. The hybrid nature of the vectorial modes is demonstrated and the singular behaviours of the minor field components in the corners are observed. Moreover, solutions are in good agreement with those published early, which tests the validity of the present approach.

  2. Intermodal Raman Scattering between Full Vectorial Modes in Few Moded Fiber

    DEFF Research Database (Denmark)

    Rishøj, Lars Søgaard; Ramachandran, Siddharth; Rottwitt, Karsten

    2013-01-01

    We experimentally investigate intermodal Raman interaction. The pump is in the fundamental mode, HE11, and the signal is in either of two full vectorial modes, TM01 or TE01. The on-off gain is approximately 3 dB for both modes, using 4 km of few-moded fiber and 400 mW of pump power.......We experimentally investigate intermodal Raman interaction. The pump is in the fundamental mode, HE11, and the signal is in either of two full vectorial modes, TM01 or TE01. The on-off gain is approximately 3 dB for both modes, using 4 km of few-moded fiber and 400 mW of pump power....

  3. An improved three-dimensional full-vectorial finite-difference imaginary-distance beam propagation method

    Institute of Scientific and Technical Information of China (English)

    XIAO Jinbiao; LIU Xu; CAI Chun; FAN Hehong; SUN Xiaohan

    2006-01-01

    A modified alternating direction implicit approach is proposed to discretize the three-dimensional full-vectorial beam propagation method (3D-FV-BPM) formulation along the longitudinal direction. The cross-coupling terms (CCTs) are neglected at the first substep, and then double used at the second substep. The order of two substeps is reversed for each transverse electric field component so that the CCTs are always expressed in an implicit form, thus the calculation is efficient and stable. Based on the multinomial interpolation, a universal finite difference scheme with a high accuracy is developed to approximate the 3D-FV-BPM formulation along the transverse directions, in which the discontinuities of the normal components of the electric field across the abrupt dielectric interfaces are taken into account and can be applied to both uniform and non-uniform grids. The corresponding imaginary-distance procedure is first applied to a buried rectangular and a GaAs-based deeply-etched rib waveguide. The field patterns and the normalized propagation constants of the fundamental and the first order modes are presented and the hybrid nature of the full-vectorial guided-modes is demonstrated, which shows the validity and utility of the present approach. Then the modal characteristics of the deeply- and shallow-etched rib waveguides based on the InGaAsp/InGaAsP strained multiple quantum wells in InP substrate are investigated in detail. The results are necessary for modeling and the design of the planar lightwave circuits or photonic integrated circuits based on these waveguides.

  4. Full-vectorial finite-difference beam propagation method based on the modified alternating direction implicit method

    Institute of Scientific and Technical Information of China (English)

    Xiao Jin-Biao; Sun Xiao-Han

    2006-01-01

    A modified alternating direction implicit algorithm is proposed to solve the full-vectorial finite-difference beam propagation method formulation based on H fields. The cross-coupling terms are neglected in the first sub-step, but evaluated and doubly used in the second sub-step. The order of two sub-steps is reversed for each transverse magnetic field component so that the cross-coupling terms are always expressed in implicit form, thus the calculation is very efficient and stable. Moreover, an improved six-point finite-difference scheme with high accuracy independent of specific structures of waveguide is also constructed to approximate the cross-coupling terms along the transverse directions. The imaginary-distance procedure is used to assess the validity and utility of the present method. The field patterns and the normalized propagation constants of the fundamental mode for a buried rectangular waveguide and a rib waveguide are presented. Solutions are in excellent agreement with the benchmark results from the modal transverse resonance method.

  5. Full-vectorial analysis of the directional couplers in vertical multiple-slotted silicon wires with trapezoidal cross-section%梯形截面硅基垂直多槽纳米线定向耦合器全矢量分析

    Institute of Scientific and Technical Information of China (English)

    肖金标; 李文亮; 夏赛赛; 孙小菡

    2012-01-01

    采用一种基于三电场分量的全矢量有限元法,其中引入了完善匹配层(PML)吸收边界条件,分析由梯形截面硅基垂直多槽纳米线构成的平行定向耦合器.考虑了波导侧壁倾角、耦合波导间距、槽宽及槽折射率的变化对定向耦合器性能的影响.给出了准TE与准TM偶、奇模有效折射率、耦合长度及模场分布,揭示了其模式的混合特性及模场分布特点.分析结果表明,恰当选择结构参数及材料参数,可实现两偏振态下相同耦合长度,定向耦合器在偏振无关条件下工作.%A directional coupler composed of two vertical multiple-slotted silicon wires with trapezoidal cross-section is characterized using a full-vectorial finite element method in terms of the electric fields, where the perfectly matched layer absorbing boundary conditions are adopted. The effects of the structural or material parameters including the sidewall angle , the gap between the coupled waveguides, and the width and index profiles in the slot regions on the behaviors of the directional coupler are taken into account. The effective indexes of the even and odd modes and the corresponding coupling length, both in quasi-TE and quasi-TM modes, are presented. The strongly-hybrid nature of the guided-modes is effectively demonstrated. The results show that polarization-independent directional couplers can be realized by properly choosing the structural and material parameters.

  6. Versatile, high sensitivity, and automatized angular dependent vectorial Kerr magnetometer for the analysis of nanostructured materials.

    Science.gov (United States)

    Teixeira, J M; Lusche, R; Ventura, J; Fermento, R; Carpinteiro, F; Araujo, J P; Sousa, J B; Cardoso, S; Freitas, P P

    2011-04-01

    Magneto-optical Kerr effect (MOKE) magnetometry is an indispensable, reliable, and one of the most widely used techniques for the characterization of nanostructured magnetic materials. Information, such as the magnitude of coercive fields or anisotropy strengths, can be readily obtained from MOKE measurements. We present a description of our state-of-the-art vectorial MOKE magnetometer, being an extremely versatile, accurate, and sensitivity unit with a low cost and comparatively simple setup. The unit includes focusing lenses and an automatized stepper motor stage for angular dependent measurements. The performance of the magnetometer is demonstrated by hysteresis loops of Co thin films displaying uniaxial anisotropy induced on growth, MnIr/CoFe structures exhibiting the so called exchange bias effect, spin valves, and microfabricated flux guides produced by optical lithography.

  7. Assessing the vulnerability of Brazilian municipalities to the vectorial transmission of Trypanosoma cruzi using multi-criteria decision analysis.

    Science.gov (United States)

    Vinhaes, Márcio Costa; de Oliveira, Stefan Vilges; Reis, Priscilleyne Ouverney; de Lacerda Sousa, Ana Carolina; Silva, Rafaella Albuquerque E; Obara, Marcos Takashi; Bezerra, Cláudia Mendonça; da Costa, Veruska Maia; Alves, Renato Vieira; Gurgel-Gonçalves, Rodrigo

    2014-09-01

    Despite the dramatic reduction in Trypanosoma cruzi vectorial transmission in Brazil, acute cases of Chagas disease (CD) continue to be recorded. The identification of areas with greater vulnerability to the occurrence of vector-borne CD is essential to prevention, control, and surveillance activities. In the current study, data on the occurrence of domiciliated triatomines in Brazil (non-Amazonian regions) between 2007 and 2011 were analyzed. Municipalities' vulnerability was assessed based on socioeconomic, demographic, entomological, and environmental indicators using multi-criteria decision analysis (MCDA). Overall, 2275 municipalities were positive for at least one of the six triatomine species analyzed (Panstrongylus megistus, Triatoma infestans, Triatoma brasiliensis, Triatoma pseudomaculata, Triatoma rubrovaria, and Triatoma sordida). The municipalities that were most vulnerable to vector-borne CD were mainly in the northeast region and exhibited a higher occurrence of domiciliated triatomines, lower socioeconomic levels, and more extensive anthropized areas. Most of the 39 new vector-borne CD cases confirmed between 2001 and 2012 in non-Amazonian regions occurred within the more vulnerable municipalities. Thus, MCDA can help to identify the states and municipalities that are most vulnerable to the transmission of T. cruzi by domiciliated triatomines, which is critical for directing adequate surveillance, prevention, and control activities. The methodological approach and results presented here can be used to enhance CD surveillance in Brazil.

  8. Vectorial Radio Interferometry with LOPES 3D

    CERN Document Server

    Huber, D; Arteaga, J C; Bähren, L; Bekk, K; Bertaina, M; Biermann, P L; Blümer, J; Bozdog, H; Brancus, I M; Chiavassa, A; Daumiller, K; de Souza, V; Di Pierro, F; Doll, P; Engel, R; Falcke, H; Fuchs, B; Fuhrmann, D; Gemmeke, H; Grupen, C; Haungs, A; Heck, D; Hörandel, J R; Horneffer, A; Huege, T; Isar, P G; Kampert, K H; Kang, D; Krömer, O; Kuijpers, J; Link, K; Łuczak, P; Ludwig, M; Mathes, H J; Melissas, M; Morello, C; Oehlschläger, J; Palmieri, N; Pierog, T; Rautenberg, J; Rebel, H; Roth, M; Rühle, C; Saftoiu, A; Schieler, H; Schmid, A; Schröder, F G; Sima, O; Toma, G; Trinchero, G C; Weindl, A; Wochele, J; Wommer, M; Zabierowski, J; Zensus, J A

    2013-01-01

    One successful detection technique for high-energy cosmic rays is based on the radio signal emitted by the charged particles in an air shower. The LOPES experiment at Karlsruhe Institute of Technology, Germany, has made major contributions to the evolution of this technique. LOPES was reconfigured several times to improve and further develop the radio detection technique. In the latest setup LOPES consisted of 10 tripole antennas. With this, LOPES 3D was the first cosmic ray experiment measuring all three vectorial field components at once and thereby gaining the full information about the electric field vector. We present an analysis based on the data taken with special focus on the benefits of a direct measurement of the vertical polarization component. We demonstrate that by measuring all polarization components the detection and reconstruction efficiency is increased and noisy single channel data can be reconstructed by utilising the information from the other two channels of one antenna station.

  9. An age-structured extension to the vectorial capacity model.

    Directory of Open Access Journals (Sweden)

    Vasiliy N Novoseltsev

    Full Text Available BACKGROUND: Vectorial capacity and the basic reproductive number (R(0 have been instrumental in structuring thinking about vector-borne pathogen transmission and how best to prevent the diseases they cause. One of the more important simplifying assumptions of these models is age-independent vector mortality. A growing body of evidence indicates that insect vectors exhibit age-dependent mortality, which can have strong and varied affects on pathogen transmission dynamics and strategies for disease prevention. METHODOLOGY/PRINCIPAL FINDINGS: Based on survival analysis we derived new equations for vectorial capacity and R(0 that are valid for any pattern of age-dependent (or age-independent vector mortality and explore the behavior of the models across various mortality patterns. The framework we present (1 lays the groundwork for an extension and refinement of the vectorial capacity paradigm by introducing an age-structured extension to the model, (2 encourages further research on the actuarial dynamics of vectors in particular and the relationship of vector mortality to pathogen transmission in general, and (3 provides a detailed quantitative basis for understanding the relative impact of reductions in vector longevity compared to other vector-borne disease prevention strategies. CONCLUSIONS/SIGNIFICANCE: Accounting for age-dependent vector mortality in estimates of vectorial capacity and R(0 was most important when (1 vector densities are relatively low and the pattern of mortality can determine whether pathogen transmission will persist; i.e., determines whether R(0 is above or below 1, (2 vector population growth rate is relatively low and there are complex interactions between birth and death that differ fundamentally from birth-death relationships with age-independent mortality, and (3 the vector exhibits complex patterns of age-dependent mortality and R(0 ∼ 1. A limiting factor in the construction and evaluation of new age

  10. Nonparaxial Propagation of Vectorial Elliptical Gaussian Beams

    Directory of Open Access Journals (Sweden)

    Wang Xun

    2016-01-01

    Full Text Available Based on the vectorial Rayleigh-Sommerfeld diffraction integral formulae, analytical expressions for a vectorial elliptical Gaussian beam’s nonparaxial propagating in free space are derived and used to investigate target beam’s propagation properties. As a special case of nonparaxial propagation, the target beam’s paraxial propagation has also been examined. The relationship of vectorial elliptical Gaussian beam’s intensity distribution and nonparaxial effect with elliptic coefficient α and waist width related parameter fω has been analyzed. Results show that no matter what value of elliptic coefficient α is, when parameter fω is large, nonparaxial conclusions of elliptical Gaussian beam should be adopted; while parameter fω is small, the paraxial approximation of elliptical Gaussian beam is effective. In addition, the peak intensity value of elliptical Gaussian beam decreases with increasing the propagation distance whether parameter fω is large or small, and the larger the elliptic coefficient α is, the faster the peak intensity value decreases. These characteristics of vectorial elliptical Gaussian beam might find applications in modern optics.

  11. Transfer Scheme Evaluation Model for a Transportation Hub based on Vectorial Angle Cosine

    Directory of Open Access Journals (Sweden)

    Li-Ya Yao

    2014-07-01

    Full Text Available As the most important node in public transport network, efficiency of a transport hub determines the entire efficiency of the whole transport network. In order to put forward effective transfer schemes, a comprehensive evaluation index system of urban transport hubs’ transfer efficiency was built, evaluation indexes were quantified, and an evaluation model of a multi-objective decision hub transfer scheme was established based on vectorial angle cosine. Qualitative and quantitative analysis on factors affecting transfer efficiency is conducted, which discusses the passenger satisfaction, transfer coordination, transfer efficiency, smoothness, economy, etc. Thus, a new solution to transfer scheme utilization was proposed.

  12. Generalized Full-Information Item Bifactor Analysis

    Science.gov (United States)

    Cai, Li; Yang, Ji Seung; Hansen, Mark

    2011-01-01

    Full-information item bifactor analysis is an important statistical method in psychological and educational measurement. Current methods are limited to single-group analysis and inflexible in the types of item response models supported. We propose a flexible multiple-group item bifactor analysis framework that supports a variety of…

  13. Vectorial spatial solitons in bulk periodic quadratically nonlinear media

    Energy Technology Data Exchange (ETDEWEB)

    Panoiu, N-C [Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY 10027 (United States); Mihalache, D [Department of Theoretical Physics, Institute of Atomic Physics, PO Box MG-6, Bucharest (Romania); Mazilu, D [Department of Theoretical Physics, Institute of Atomic Physics, PO Box MG-6, Bucharest (Romania); Lederer, F [Institute of Solid State Theory and Theoretical Optics, Friedrich Schiller University Jena, Max-Wien-Platz 1, Jena, D-07743 (Germany); Osgood, R M Jr [Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY 10027 (United States)

    2004-05-01

    We present a comprehensive analysis of the generation, propagation and characteristic properties of two-dimensional spatial solitons formed in quasi-phase-matched gratings through type-II vectorial interaction. By employing an averaging approach based on asymptotic expansion theory, we show that the dynamics of soliton propagation in the grating and their stability properties are strongly influenced by induced Kerr-like nonlinearities. Finally, through extensive numerical simulations, we verify the validity of our theoretical predictions.

  14. Full profile incoherent scatter analysis at Jicamarca

    Directory of Open Access Journals (Sweden)

    D. L. Hysell

    2008-02-01

    Full Text Available Incoherent scatter data from a hybrid long-pulse/double-pulse experiment at Jicamarca are analyzed using a full-profile analysis similar to the one implemented by Holt et al. (1992. In this case, plasma density, electron and ion temperatures, and light ion composition profiles in the topside are estimated simultaneously. Full-profile analysis is crucial at Jicamarca, since the long correlation time of the incoherent scatter signal at 50 MHz invalidates conventional gated analysis. Results for a 24 h interval in April of 2006 are presented, covering altitudes through 1600 km with 10 min time resolution, and compared with results from the NRL ionospheric model SAMI2. The analysis provides the first comprehensive assessment of ionospheric conditions over Jicamarca at sunrise as well as the first 24-h record of helium ion layers. Possible refinements to the experiment and the algorithm are discussed.

  15. Vectorial role of some dermanyssoid mites (Acari, Mesostigmata, Dermanyssoidea

    Directory of Open Access Journals (Sweden)

    Valiente Moro C.

    2005-06-01

    Full Text Available Among transmissible diseases, vectorial diseases represent a major problem for public health. In the group of acarina, while ticks are the most commonly implicated vectors, other arthropods and notably Dermanyssoidea are also involved in the transmission of pathogenic agents. Since the role of this superfamily is at present largely unknown, we have reviewed the vectorial role of these mites in the appearance, survival and propagation of pathogens. Various authors have shown that Dermanyssoidea are implicated in the transmission of both bacteria (Salmonella, Spirocheta, Rickettsia or Pasteurella and viruses (equine encephalitis viruses, West Nile virus, Fowl pox virus, the virus causing Newcastle disease and tick borne encephalitis viruses or hantaviruses. Finally, some authors have also shown their role in the transmission of some protozoa and filaria. As the vectorial character of such mites has been more clearly demonstrated (Dermanyssus gallinae, Ornithonyssus bacoti and Allodermanyssus sanguineus, it would be interesting to continue studies to better understand the role of this superfamily in the epidemiology of certain zoonoses.

  16. Resolution analysis in full waveform inversion

    NARCIS (Netherlands)

    Fichtner, A.; Trampert, J.

    2011-01-01

    We propose a new method for the quantitative resolution analysis in full seismic waveform inversion that overcomes the limitations of classical synthetic inversions while being computationally more efficient and applicable to any misfit measure. The method rests on (1) the local quadratic approximat

  17. Vectorial rotating vortex Hankel laser beams

    Science.gov (United States)

    Kotlyar, Victor V.; Kovalev, Alexey A.; Soifer, Victor A.

    2016-09-01

    We propose a generalization of spherical waves in the form of linearly polarized beams with embedded optical vortices. The source of these beams is an infinitely narrow light ring with an infinitely small radius. These vectorial beams are obtained based on scalar Hankel beams discovered by the authors recently. We have derived explicit relations for complex amplitudes of all six components of vectorial vortex Hankel beams. A closed analytical expression for the axial projection of the orbital angular momentum density in far field has been obtained. We also showed that the intensity distribution of the electric vector rotates by 90 degrees upon the beam propagation in near field.

  18. Vectorial Hermite-Laguerre-Gaussian beams beyond the paraxial approximation

    Institute of Scientific and Technical Information of China (English)

    Wang Bei-Zhan; Zhao Zhi-Guo; Lü Bai-Da; Duan Kai-Liang

    2007-01-01

    Starting from the vectorial Rayleigh-Sommerfeld integrals, the free-space propagation expressions for vectorial Hermite-Laguerre-Gaussian (HLG) beams beyond the paraxial approximation are derived. The far-field expressions and the scalar paraxial results are given as special cases of our general expressions. The intensity distributions of vectorial nonparaxial HLG beams are studied and illustrated with numerical examples.

  19. A Vectorial Capacity Product to Monitor Changing Malaria Transmission Potential in Epidemic Regions of Africa

    Directory of Open Access Journals (Sweden)

    Pietro Ceccato

    2012-01-01

    Full Text Available Rainfall and temperature are two of the major factors triggering malaria epidemics in warm semi-arid (desert-fringe and high altitude (highland-fringe epidemic risk areas. The ability of the mosquitoes to transmit Plasmodium spp. is dependent upon a series of biological features generally referred to as vectorial capacity. In this study, the vectorial capacity model (VCAP was expanded to include the influence of rainfall and temperature variables on malaria transmission potential. Data from two remote sensing products were used to monitor rainfall and temperature and were integrated into the VCAP model. The expanded model was tested in Eritrea and Madagascar to check the viability of the approach. The analysis of VCAP in relation to rainfall, temperature and malaria incidence data in these regions shows that the expanded VCAP correctly tracks the risk of malaria both in regions where rainfall is the limiting factor and in regions where temperature is the limiting factor. The VCAP maps are currently offered as an experimental resource for testing within Malaria Early Warning applications in epidemic prone regions of sub-Saharan Africa. User feedback is currently being collected in preparation for further evaluation and refinement of the VCAP model.

  20. Spatial technologies to evaluate vectorial samples quality in maps production

    Directory of Open Access Journals (Sweden)

    Abraham Cárdenas Tristán

    2013-01-01

    Full Text Available A pesar de importantes progresos realizados en la materia en los últimos años, la conceptualización de la metodología para evaluar la calidad de vectores que integran la cartografía digital es aún una tarea complicada, no existiendo un esquema oficial de evaluación de la calidad de la producción cartográfica vectorial en el país. Se propone una metodología para evaluar la calidad de la producción cartográfica a través del análisis de muestras aplicadas a las diversas escalas vectoriales de la cobertura del territorio de la República Mexicana. Las pruebas realizadas con el uso de diversas tecnologías espaciales, se encuentran dentro la norma TC/211 (ISO19113 e ISO19114, éstas han sido desarrolladas con el apoyo de compañías productoras de nuevas tecnologías espaciales así como del organismo oficial, productor de información vectorial en el país. Se tiene como objetivo buscar justificaciones pertinentes e indicadores potenciales, para determinar normas o modelos específicos de evaluación de la calidad, beneficiando el potencial de la producción cartográfica en el aprovechamiento de los recursos naturales y las frecuentes aplicaciones potenciales de la misma. La metodología utilizada va a la par de los avances en la investigación para establecer una mejora en las políticas de evaluación y de edición de cartografía vectorial, llevada a cabo por organismos internacionales, universidades y centros de investigación.

  1. COERCIVITY AND VECTOR MAGNETIZATION ANALYSIS OF OBSIDIAN SAMPLES FROM THE TRANS-MEXICAN VOLCANIC BELT (Coercitividad y análisis de magnetización vectorial de muestras de obsidianas de la faja volcánica transmexicana

    Directory of Open Access Journals (Sweden)

    Jaime Urrutia-Fucugauchi

    2017-09-01

    Full Text Available This note presents initial results of a paleomagnetic study of obsidian from twenty localities in the eastern, central and western sectors of the Trans-Mexican volcanic belt in central Mexico. We focus on the coercivity and vector composition of the remanent magnetization, which are critical for paleodirectional and paleointensity studies. Alternating field demagnetization shows that obsidians carry single and two-component magnetizations residing in low- and high-coercivity magnetic minerals, with discrete and overlapping coercivity spectra. Magnetic minerals are likely iron-titanium oxides with fine-grain sizes characterized by pseudo-single domain states. ESPAÑOL: Se presentan los resultados preliminares del estudio de obsidianas de veinte localidades en los sectores este, central y oeste de la faja volcánica transmexicana. Los análisis se concentran en la coercitividad y la composición vectorial de la magnetización remanente, que son propiedades claves para evaluar los registros de direcciones e intensidades. La desmagnetización por campos alternos revela la presencia de magnetizaciones de una y dos componentes, que residen en minerales con baja y alta coercitividad con espectros que traslapan y discretos. Los minerales magnéticos son óxidos de hierro-titanio con grano fino y estados de dominio seudosencillo.

  2. Vectorial optical fields fundamentals and applications

    CERN Document Server

    2014-01-01

    Polarization is a vector nature of light that plays an important role in optical science and engineering. While existing textbook treatments of light assume beams with spatially homogeneous polarization, there is an increasing interest in vectorial optical fields with spatially engineered states of polarization. New effects and phenomena have been predicted and observed for light beams with these unconventional polarization states. This edited review volume aims to provide a comprehensive overview and summarize the latest developments in this important emerging field of optics. This book will cover the fundamentals including mathematical and physical descriptions, experimental generation, manipulation, focusing, propagation, and the applications of the engineered vectorial optical fields in focal field engineering, plasmonic focusing and optical antenna, single molecular imaging, optical tweezers/trapping, as well as optical measurements and instrumentations. Readership: Students, professionals, post-graduat...

  3. Las funciones de Cobb-Douglas como base del espacio vectorial de funciones homogéneas.

    Directory of Open Access Journals (Sweden)

    Díaz Martínez, Zuleyka.

    2003-01-01

    Full Text Available Dado que el conjunto de funciones homogéneas de grado r forma un espacio vectorial real, el objetivo de este trabajo es mostrar que el conjunto de funciones de Cobb- Douglas de grado r, XαYr-α, forma una base de dicho espacio vectorial, lo que puede resultar de interés dada la importancia que las funciones de Cobb- Douglas tienen en Economía.Dado que el conjunto de funciones homogéneas de grado r forma un espacio vectorial real, el objetivo de este trabajo es mostrar que el conjunto de funciones de Cobb- Douglas de grado r, XαYr-α, forma una base de dicho espacio vectorial, lo que puede resultar de interés dada la importancia que las funciones de Cobb- Douglas tienen en Economía.

  4. Bioelectrical impedance vectorial analysis and nutritional status of older women according. 10.5007/1980-0037.2011v13n6p415

    Directory of Open Access Journals (Sweden)

    Sandra Maria Lima Ribeiro

    2011-11-01

    Full Text Available The objective of the present study was to compare and discuss the nutritional status of older women according to different categories of BMI. Additionally, the study was aimed at introducing the bioelectrical impedance vector analysis (BIVA as a tool to assess the nutritional status. Thirty-two women (60 years or older, physically independent, and with moderate level of physical activity were divided into three groups according toBMI classification: G1 (BMI28 Kg/ m2. The following variables were analyzed as indicators of nutritional status: body mass and height to calculate BMI, waist circumference (WC, hip circumference (HC, waisthipratio (WHR, bioelectrical impedance (BIVA, resting energy expenditure (REE, biochemical markers of nutritional status (glucose, total cholesterol, and fractions, IGF-1, and leptin. The groups were compared using ANOVA and the Hotelling’s T 2 test for vector analysis. The main findings based on vector displacement showed lower reactance and higher resistance in G1. G3 showed the highest values of CC and leptin, and also lower REE. Therefore, higher BMI suggested at the same time higher cell mass and higher risk of developing chronic diseases. In turn, lower BMI values suggested reduced fat-free body mass. These results confirm the search for specific classification of BMI for the elderly and suggest the BIVA as a viable alternative in physical and nutritional assessment.

  5. Hybrid tenso-vectorial compressive sensing for hyperspectral imaging

    Science.gov (United States)

    Li, Qun; Bernal, Edgar A.

    2016-05-01

    Hyperspectral imaging has a wide range of applications relying on remote material identification, including astronomy, mineralogy, and agriculture; however, due to the large volume of data involved, the complexity and cost of hyperspectral imagers can be prohibitive. The exploitation of redundancies along the spatial and spectral dimensions of a hyperspectral image of a scene has created new paradigms that overcome the limitations of traditional imaging systems. While compressive sensing (CS) approaches have been proposed and simulated with success on already acquired hyperspectral imagery, most of the existing work relies on the capability to simultaneously measure the spatial and spectral dimensions of the hyperspectral cube. Most real-life devices, however, are limited to sampling one or two dimensions at a time, which renders a significant portion of the existing work unfeasible. We propose a new variant of the recently proposed serial hybrid vectorial and tensorial compressive sensing (HCS-S) algorithm that, like its predecessor, is compatible with real-life devices both in terms of the acquisition and reconstruction requirements. The newly introduced approach is parallelizable, and we abbreviate it as HCS-P. Together, HCS-S and HCS-P comprise a generalized framework for hybrid tenso-vectorial compressive sensing, or HCS for short. We perform a detailed analysis that demonstrates the uniqueness of the signal reconstructed by both the original HCS-S and the proposed HCS-P algorithms. Last, we analyze the behavior of the HCS reconstruction algorithms in the presence of measurement noise, both theoretically and experimentally.

  6. Vectorial FDBPM 3D waveguide structures

    Science.gov (United States)

    Li, Daoping; van Brug, Hedser H.; Frankena, Hans J.

    1994-08-01

    A fully vectorial finite difference beam propagation method for 3D waveguide structures, including longitudinally variant structures is presented. The transparent boundary conditions are utilized in the edges of the computational window. Both Gaussian beams and exact fields of the guided modes are launched as the starting field. Propagating fields are calculated and the power attenuation is evaluated. The choice of step size, finite difference scheme parameter and reference propagation constant is discussed. The applicability and accuracy are demonstrated for two particular waveguide structures.

  7. Evidence of vectorial photoelectric effect on Copper

    Science.gov (United States)

    Pedersoli, E.; Banfi, F.; Ressel, B.; Pagliara, S.; Giannetti, C.; Galimberti, G.; Lidia, S.; Corlett, J.; Ferrini, G.; Parmigiani, F.

    2005-08-01

    Quantum efficiency (QE) measurements of single photon photoemission from a Cu(111) single crystal and a Cu polycrystal photocathodes, irradiated by 150fs-6.28eV laser pulses, are reported over a broad range of incidence angle, both in s and p polarizations. The maximum QE (≃4×10-4) for polycrystalline Cu is obtained in p polarization at an angle of incidence θ =65°. We observe a QE enhancement in p polarization which cannot be explained in terms of optical absorption, a phenomenon known as vectorial photoelectric effect. Issues concerning surface roughness and symmetry considerations are addressed. An explanation in terms of nonlocal conductivity tensor is proposed.

  8. Evidence of vectorial photoelectric effect on copper

    Energy Technology Data Exchange (ETDEWEB)

    Pedersoli, E.; Banfi, F.; Ressel, B.; Pagliara, S.; Giannetti,C.; Galimberti, G.; Lidia, S.; Corlett, J.; Ferrini, G.; Parmigiani, F.

    2005-05-27

    Quantum Efficiency (QE) measurements of single photon photoemission from a Cu(111) single crystal and a Cu polycrystal photocathodes, irradiated by 150 fs-6.28 eV laser pulses, are reported over a broad range of incidence angle, both in s and p polarizations. The maximum QE (approx. = 4x10-4) for polycrystalline Cu is obtained in p polarization at an angle of incidence theta = 65 deg. We observe a QE enhancement in p polarization which can not be explained in terms of optical absorption, a phenomenon known as vectorial photoelectric effect. Issues concerning surface roughness and symmetry considerations are addressed. An explanation in terms of non local conductivity tensor is proposed.

  9. Evaluación del peso seco y el agua corporal según bioimpedancia vectorial frente al método tradicional Assessing dry weight and body water using bioimpedance vector analysis compared to the traditional method

    Directory of Open Access Journals (Sweden)

    María Teresa Centellas Tristán

    2013-03-01

    Full Text Available Introducción: La bioimpedancia eléctrica se puede utilizar para establecer el estado de hidratación y nutrición en hemodiálisis. La valoración del estado de hidratación de los pacientes se hace habitualmente a modo de "arte clínico" mediante el concepto de "peso seco". Existen pocos trabajos que estudien la concordancia entre el peso seco estimado de forma clínica y el deducido post-bioimpedancia. Material y métodos: Se estudiaron 36 pacientes (26 varones y 10 mujeres. Se realizó bioimpedancia eléctrica vectorial antes y 30' después de diálisis de mitad de semana midiendo, el peso, el agua total y su distribución, el ángulo de fase, la relación de Na/K, y la posición del vector de cada paciente en el normograma de esferas: percentiles 50,75 y 95. El peso-seco se estimó según la valoración subjetiva del nefrólogo, enfermera y paciente. Además en 12 pacientes estables se continuó el análisis por bioimpedancia durante 4 semanas. Resultados: La edad fue de 69.6±12.5 (r=29-89. Prediálisis el peso fue de 73.1±14.1, y postdiálisis de 70.4±13.6. El agua corporal total fue de 24.7±2.8 L/m (53.7±8.2% del peso; 22.1±3.0 L (56.2±5.9% del peso correspondían a agua extracelular y 17.4±3.8 L/m a intracelular. post-hemodiálisis, el agua total se redujo a 22.8±2.4 L/m (51.8±8.6% del peso (23.5±2.2 L en varones; y 21,5±3 L en mujeres de los que 19.6±2.5 L (54,3±5.8% del peso correspondían a agua extracelular y 16.7±3.3 a agua intracelular. Un varón y 5 mujeres sobrepasaron el valor de referencia más alto. El peso post-hemodiálisis fue de 70,4±13,6 ligeramente superior al peso seco establecido: 70,2±13,4 (p=0,02. El ángulo de fase fue 1.2, indicando malnutrición. El estudio de las elipses mostró en el percentil 50 el 58.3% (21 pacientes. El resto se repartían en el 75% de sobrehidratación: 9 (25% y en el 95%, 5 (13,8%. En los 12 pacientes en los que se efectuaron las bioimpedancias seriadas durante 4 semanas

  10. Stable vortex solitons in a vectorial cubic-quintic model

    Energy Technology Data Exchange (ETDEWEB)

    Mihalache, D [Department of Theoretical Physics, Institute of Atomic Physics, PO Box MG-6, Bucharest (Romania); Mazilu, D [Department of Theoretical Physics, Institute of Atomic Physics, PO Box MG-6, Bucharest (Romania); Malomed, B A [Department of Interdisciplinary Studies, Faculty of Engineering, Tel Aviv University, Tel Aviv 69978 (Israel); Lederer, F [Institute of Solid State Theory and Theoretical Optics, Friedrich-Schiller Universitaet Jena, Max-Wien-Platz 1, D-07743, Jena (Germany)

    2004-05-01

    We investigate the stability of vectorial (two-component) vortex solitons of two types. Their stationary shapes are identical, but their stability (which is the most important issue for spinning solitons) is drastically different. These are solitons with vorticities (S,S) and (S,-S) in the two components. The analysis is performed in a vectorial cubic-quintic model, with the two components nonlinearly coupled by the incoherent cross-phase-modulation interaction, but we expect that the results are quite generic. The stability was investigated by means of computing eigenvalues of perturbations around the stationary solitons, as well as in direct simulations. We also report new analytical results for the well-known problem of the description of the stationary form of scalar solitons in media of this type. The analytical results explain the shape of the spinning solitons, and the strong dependence of their norm (power) on the vorticity, in both the 2D and 3D cases. In this paper we also give the first estimate of the physical characteristics (power and radius) of the stable solitons with different values of S, making use of recently measured values of the necessary nonlinear parameters. All the two-component solitons of type (S,-S) are unstable. In contrast, those of type (S,S) have their stability regions, the size of which strongly depends on S. An unstable soliton always splits into a set of separating zero-spin ones, in precise compliance with the azimuthal index of the most unstable perturbation eigenmode. Direct simulations demonstrate that stable solitons readily self-trap from arbitrary initial pulses which belong to their topological class.

  11. A vectorial semantics approach to personality assessment.

    Science.gov (United States)

    Neuman, Yair; Cohen, Yochai

    2014-04-23

    Personality assessment and, specifically, the assessment of personality disorders have traditionally been indifferent to computational models. Computational personality is a new field that involves the automatic classification of individuals' personality traits that can be compared against gold-standard labels. In this context, we introduce a new vectorial semantics approach to personality assessment, which involves the construction of vectors representing personality dimensions and disorders, and the automatic measurements of the similarity between these vectors and texts written by human subjects. We evaluated our approach by using a corpus of 2468 essays written by students who were also assessed through the five-factor personality model. To validate our approach, we measured the similarity between the essays and the personality vectors to produce personality disorder scores. These scores and their correspondence with the subjects' classification of the five personality factors reproduce patterns well-documented in the psychological literature. In addition, we show that, based on the personality vectors, we can predict each of the five personality factors with high accuracy.

  12. A Vectorial Semantics Approach to Personality Assessment

    Science.gov (United States)

    Neuman, Yair; Cohen, Yochai

    2014-04-01

    Personality assessment and, specifically, the assessment of personality disorders have traditionally been indifferent to computational models. Computational personality is a new field that involves the automatic classification of individuals' personality traits that can be compared against gold-standard labels. In this context, we introduce a new vectorial semantics approach to personality assessment, which involves the construction of vectors representing personality dimensions and disorders, and the automatic measurements of the similarity between these vectors and texts written by human subjects. We evaluated our approach by using a corpus of 2468 essays written by students who were also assessed through the five-factor personality model. To validate our approach, we measured the similarity between the essays and the personality vectors to produce personality disorder scores. These scores and their correspondence with the subjects' classification of the five personality factors reproduce patterns well-documented in the psychological literature. In addition, we show that, based on the personality vectors, we can predict each of the five personality factors with high accuracy.

  13. Uniqueness of the potential function for the vectorial Sturm-Liouville equation on a finite interval

    Directory of Open Access Journals (Sweden)

    Chang Tsorng-Hwa

    2011-01-01

    Full Text Available Abstract In this paper, the vectorial Sturm-Liouville operator L Q = - d 2 d x 2 + Q ( x is considered, where Q(x is an integrable m × m matrix-valued function defined on the interval [0,π] The authors prove that m 2+1 characteristic functions can determine the potential function of a vectorial Sturm-Liouville operator uniquely. In particular, if Q(x is real symmetric, then m ( m + 1 2 + 1 characteristic functions can determine the potential function uniquely. Moreover, if only the spectral data of self-adjoint problems are considered, then m 2 + 1 spectral data can determine Q(x uniquely.

  14. Ecological aspects of the vectorial control of Chagas' disease in Brazil

    Directory of Open Access Journals (Sweden)

    Dias João Carlos P.

    1994-01-01

    Full Text Available The feasibility and most important ecological aspects of vectorial Chagas' disease control are discussed. The spread and maintenance of this disease involve multiple ecological and sociopolitical factors that must be taken into account when control programs are planned, executed and evaluated. In spite of its complexity, Chagas disease can be controlled using methods that target specific mechanisms of transmission, the most important being vectorial and transfusional. Major ecological problems in Chagas' disease control do not exist, even in the case of the chemical control of triatomine vectors. The main challenges for the Brazilian Control Program at this moment are: its maintenance as a political priority; the threat of peridomestic vectors; and the consolidation of permanent horizontal and participative epidemiological surveillance systems against the vector.

  15. Method for improving accuracy in full evaporation headspace analysis.

    Science.gov (United States)

    Xie, Wei-Qi; Chai, Xin-Sheng

    2017-03-21

    We report a new headspace analytical method in which multiple headspace extraction is incorporated with the full evaporation technique. The pressure uncertainty caused by the solid content change in the samples has a great impact to the measurement accuracy in the conventional full evaporation headspace analysis. The results (using ethanol solution as the model sample) showed that the present technique is effective to minimize such a problem. The proposed full evaporation multiple headspace extraction analysis technique is also automated and practical, and which could greatly broaden the applications of the full-evaporation-based headspace analysis. This article is protected by copyright. All rights reserved.

  16. Quantitative global studies of reactomes and metabolomes using a vectorial representation of reactions and chemical compounds

    Directory of Open Access Journals (Sweden)

    Triviño Juan C

    2010-04-01

    Full Text Available Abstract Background Global studies of the protein repertories of organisms are providing important information on the characteristics of the protein space. Many of these studies entail classification of the protein repertory on the basis of structure and/or sequence similarities. The situation is different for metabolism. Because there is no good way of measuring similarities between chemical reactions, there is a barrier to the development of global classifications of "metabolic space" and subsequent studies comparable to those done for protein sequences and structures. Results In this work, we propose a vectorial representation of chemical reactions, which allows them to be compared and classified. In this representation, chemical compounds, reactions and pathways may be represented in the same vectorial space. We show that the representation of chemical compounds reflects their physicochemical properties and can be used for predictive purposes. We use the vectorial representations of reactions to perform a global classification of the reactome of the model organism E. coli. Conclusions We show that this unsupervised clustering results in groups of enzymes more coherent in biological terms than equivalent groupings obtained from the EC hierarchy. This hierarchical clustering produces an optimal set of 21 groups which we analyzed for their biological meaning.

  17. A Fast Alternating Minimization Algorithm for Nonlocal Vectorial Total Variational Multichannel Image Denoising

    Directory of Open Access Journals (Sweden)

    Rubing Xi

    2014-01-01

    Full Text Available The variational models with nonlocal regularization offer superior image restoration quality over traditional method. But the processing speed remains a bottleneck due to the calculation quantity brought by the recent iterative algorithms. In this paper, a fast algorithm is proposed to restore the multichannel image in the presence of additive Gaussian noise by minimizing an energy function consisting of an l2-norm fidelity term and a nonlocal vectorial total variational regularization term. This algorithm is based on the variable splitting and penalty techniques in optimization. Following our previous work on the proof of the existence and the uniqueness of the solution of the model, we establish and prove the convergence properties of this algorithm, which are the finite convergence for some variables and the q-linear convergence for the rest. Experiments show that this model has a fabulous texture-preserving property in restoring color images. Both the theoretical derivation of the computation complexity analysis and the experimental results show that the proposed algorithm performs favorably in comparison to the widely used fixed point algorithm.

  18. Full-spectrum analysis of natural gamma-ray spectra

    NARCIS (Netherlands)

    Hendriks, Peter; Limburg, J; de Meijer, RJ

    2001-01-01

    In this paper, a new system to measure natural gamma -radiation in situ will be presented. This system combines a high-efficiency EGO scintillation detector with full-spectrum data analysis (FSA). This technique uses the (nearly) full spectral shape and the so-called 'standard spectra' to calculate

  19. Vectorial approach of determining the wave propagation at metasurfaces

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Daniel, E-mail: D.Smith1966@outlook.com [Physics Department, Carnegie Mellon University, Pittsburgh, PA 15213 (United States); Campbell, Michael, E-mail: mhl.campbell@gmail.com [School of Mathematics and Physics, Queens University, Belfast BT7 1NN (United Kingdom); Bergmann, Andreas, E-mail: a.bergmann@hotmail.com [Department of Physics, University of Hamburg, 20355 Hamburg (Germany)

    2015-10-15

    Vector approach often benefits optical engineers and physicists, and a vector formulation of the laws of reflection and refraction has been studied (Tkaczyk, 2012). However, the conventional reflection and refraction laws may be violated in the presence of a metasurface, and reflection and refraction at the metasurface obey generalized laws of reflection and refraction (Yu et al., 2011). In this letter, the vectorial laws of reflection and refraction at the metasurface were derived, and the matrix formulation of these vectorial laws are also obtained. These results enable highly efficient and unambiguous computations in ray-tracing problems that involve a metasurface.

  20. Fully vectorial accelerating diffraction-free Helmholtz beams.

    Science.gov (United States)

    Aleahmad, Parinaz; Miri, Mohammad-Ali; Mills, Matthew S; Kaminer, Ido; Segev, Mordechai; Christodoulides, Demetrios N

    2012-11-16

    We show that new families of diffraction-free nonparaxial accelerating optical beams can be generated by considering the symmetries of the underlying vectorial Helmholtz equation. Both two-dimensional transverse electric and magnetic accelerating wave fronts are possible, capable of moving along elliptic trajectories. Experimental results corroborate these predictions when these waves are launched from either the major or minor axis of the ellipse. In addition, three-dimensional spherical nondiffracting field configurations are presented along with their evolution dynamics. Finally, fully vectorial self-similar accelerating optical wave solutions are obtained via oblate-prolate spheroidal wave functions. In all occasions, these effects are illustrated via pertinent examples.

  1. Full Dynamic Analysis of Mooring Solution Candidates - First Iteration

    DEFF Research Database (Denmark)

    Thomsen, Jonas Bjerg; Ferri, Francesco

    This report covers an initial full dynamic analysis of the mooring solutions for the four wave energy converters in the project “Mooring Solutions for Large Wave Energy Converters”. The analysis tends to provide the first understanding of the layouts and provide discussion on what parameters that...

  2. Full vector modal analysis of microstructured optical fiber propagation characteristics

    Science.gov (United States)

    Zghal, Mourad; Bahloul, Faouzi; Chatta, Rihab; Attia, Rabah; Pagnoux, Dominique; Roy, Philippe; Melin, Gilles; Gasca, Laurent

    2004-10-01

    Microstructured optical fibers (MOFs) are optical fibers having a periodic air-silica cross-section. The air holes extend along the axis of the fiber for its entire length. The core of the fiber is formed by a missing hole in the periodic structure. Remarkable properties of MOFs have recently been reported. This paper presents new work in the modeling of the propagation characteristics of MOFs using the Finite Element Method (FEM) and the Galerkin Method (GM). This efficient electromagnetic simulation package provides a vectorial description of the electromagnetic fields and of the associated effective index. This information includes accurate determination of the spectral extent of the modes, cutoff properties and mode-field distributions. We show that FEM is well adapted for describing the fields at abrupt transitions of the refractive index while GM has the advantage to accurately analyze MOFs of significant complexity using only modest computational resources. This presentation will focus on the specific techniques required to determine single mode operation, dispersion properties and effective area through careful choice of the geometrical parameters of the fibers. We demonstrate that with suitable geometrical parameters, the zero dispersion wavelength can be shifted. This tool can also provide design criteria for fabricating MOFs and a corresponding map of effective area. This approach is validated by comparison with experimental results and measurements on actual MOFs fabricated at IRCOM and at Alcatel Research and Innovation Center.

  3. Vectorial diffraction of extreme ultraviolet light and ultrashort light pulses

    NARCIS (Netherlands)

    Nugrowati, A.M.

    2008-01-01

    In this thesis, we present applications in optics involving the diffraction theory of light for two advanced technologies. We have used a rigorous vectorial diffraction method to model: (i) the imaging of mask structures in extreme ultraviolet lithography, and (ii) ultrashort pulse propagation thro

  4. AB 1007 Full Fuel Cycle Analysis (FFCA) Peer Review

    Energy Technology Data Exchange (ETDEWEB)

    Rice, D; Armstrong, D; Campbell, C; Lamont, A; Gallegos, G; Stewart, J; Upadhye, R

    2007-01-19

    LLNL is a participant of California's Advanced Energy Pathways (AEP) team funded by DOE (NETL). At the AEP technical review meeting on November 9, 2006. The AB 1007 FFCA team (Appendix A) requested LLNL participate in a peer review of the FFCA reports. The primary contact at the CEC was McKinley Addy. The following reports/presentations were received by LLNL: (1) Full Fuel Cycle Energy and Emissions Assumptions dated September 2006, TIAX; (2) Full Fuel cycle Assessment-Well to Tank Energy Inputs, Emissions, and Water Impacts dated December 2006, TIAX; and (3) Full Fuel Cycle Analysis Assessment dated October 12, 2006, TIAX.

  5. Full sequence analysis of the original Sapporo virus.

    Science.gov (United States)

    Nakanishi, Kaori; Tatsumi, Masatoshi; Kinoshita-Numata, Kazuko; Tsugawa, Takeshi; Nakata, Shuji; Tsutsumi, Hiroyuki

    2011-09-01

    In this study, the full-length genome sequence of the prototype of sapovirus, namely Sapporo virus (SV82), was identified. Sapporo virus RNA was extracted from a fecal sample, amplified by RT-PCR and the PCR products sequenced directly and analyzed. Sequence analysis showed that Sapporo virus consists of 7433 nucleotides and has three open reading frames. The Sapporo strain shows 91.7% nucleotide sequence identity to the Manchester virus. Phylogenic analysis has also revealed the closeness of Sapporo virus to other sapovirus/genogroup I strains. Basic information on the evolutionary history of sapovirus analysis is provided here.

  6. Full Information Item Factor Analysis of the FCI

    Science.gov (United States)

    Hagedorn, Eric

    2010-02-01

    Traditional factor analytical methods, principal factors or principal components analysis, are inappropriate techniques for analyzing dichotomously scored responses to standardized tests or concept inventories because they lead to artifactual factors often referred to as ``difficulty factors.'' Full information item factor analysis (Bock, Gibbons and Muraki, 1988) based on Thurstone's multiple factor model and calculated using marginal maximum likelihood estimation, is an appropriate technique for such analyses. Force Concept Inventory (Hestenes, Wells and Swackhamer, 1992) data from 1582 university students completing an introductory physics course, was analyzed using the full information item factor analysis software TESTFACT v. 4. Analyzing the statistical significance of successive factors added to the model, using chi-squared statistics, led to a six factor model interpretable in terms of the conceptual dimensions of the FCI. )

  7. Modelling polarization dependent absorption: The vectorial Lambert-Beer law

    Science.gov (United States)

    Franssens, G.

    2014-07-01

    The scalar Lambert-Beer law, describing the absorption of unpolarized light travelling through a linear non-scattering medium, is simple, well-known, and mathematically trivial. However, when we take the polarization of light into account and consider a medium with polarization dependent absorption, we now need a Vectorial Lambert-Beer Law (VLBL) to quantify this interaction. Such a generalization of the scalar Lambert-Beer law appears not to be readily available. A careful study of this topic reveals that it is not a trivial problem. We will see that the VLBL is not and cannot be a straightforward vectorized version of its scalar counterpart. The aim of the work is to present the general form of the VLBL and to explain how it arises. A reasonable starting point to derive the VLBL is the Vectorial Radiative Transfer Equation (VRTE), which models the absorption and scattering of (partially) polarized light travelling through a linear medium. When we turn off scattering, the VRTE becomes an infinitesimal model for the VLBL holding in the medium. By integrating this equation, we expect to find the VLBL. Surprisingly, this is not the end of the story. It turns out that light propagation through a medium with polarization-dependent absorption is mathematically not that trivial. The trickiness behind the VLBL can be understood in the following terms. The matrix in the VLBL, relating any input Stokes vector to the corresponding output Stokes vector, must necessarily be a Mueller matrix. The subset of invertible Mueller matrices forms a Lie group. It is known that this Lie group contains the ortho-chronous Lorentz group as a subgroup. The group manifold of this subgroup has a (well-known) non-trivial topology. Consequently, the manifold of the Lie group of Mueller matrices also has (at least the same, but likely a more general) non-trivial topology (the full extent of which is not yet known). The type of non-trivial topology, possessed by the manifold of (invertible

  8. Vectorial stimulated Raman scattering resolution on the semi-line

    Energy Technology Data Exchange (ETDEWEB)

    Ginovart, Frédéric, E-mail: Frederic.Ginovart@enssat.fr [UEB, Université Européenne de Bretagne, Université de Rennes I (France); CNRS, UMR 6082 FOTON, Enssat, 6 rue de Kerampont, BP 80518, 22305 Lannion cédex (France)

    2012-07-09

    Stimulated Raman scattering between a laser pump pulse and a Stokes pulse is considered in a two-level medium with vectorial optical fields. The model on the semi-line is proved to be solvable by inverse scattering transform scheme. Among solutions, soliton generation is discussed. Then, it is shown how rotation of the Stokes wave leads to a spike of pump radiation in the time domain. -- Highlights: ► Vectorial stimulated Raman scattering is shown to be solvable on the semi-line by the inverse scattering transform scheme. ► Solitons can be created by pairs like in the scalar stimulated Raman scattering. ► Raman spike and multi-spike can occur in the time domain when considering rotating Stokes polarization.

  9. 2D Poisson sigma models with gauged vectorial supersymmetry

    Science.gov (United States)

    Bonezzi, Roberto; Sundell, Per; Torres-Gomez, Alexander

    2015-08-01

    In this note, we gauge the rigid vectorial supersymmetry of the two-dimensional Poisson sigma model presented in arXiv:1503.05625. We show that the consistency of the construction does not impose any further constraints on the differential Poisson algebra geometry than those required for the ungauged model. We conclude by proposing that the gauged model provides a first-quantized framework for higher spin gravity.

  10. 2D Poisson sigma models with gauged vectorial supersymmetry

    Energy Technology Data Exchange (ETDEWEB)

    Bonezzi, Roberto [Dipartimento di Fisica ed Astronomia, Università di Bologna and INFN, Sezione di Bologna,via Irnerio 46, I-40126 Bologna (Italy); Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Sundell, Per [Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Torres-Gomez, Alexander [Departamento de Ciencias Físicas, Universidad Andres Bello,Republica 220, Santiago (Chile); Instituto de Ciencias Físicas y Matemáticas, Universidad Austral de Chile-UACh,Valdivia (Chile)

    2015-08-12

    In this note, we gauge the rigid vectorial supersymmetry of the two-dimensional Poisson sigma model presented in arXiv:1503.05625. We show that the consistency of the construction does not impose any further constraints on the differential Poisson algebra geometry than those required for the ungauged model. We conclude by proposing that the gauged model provides a first-quantized framework for higher spin gravity.

  11. 2D Poisson sigma models with gauged vectorial supersymmetry

    OpenAIRE

    2015-01-01

    In this note, we gauge the rigid vectorial supersymmetry of the two-dimensional Poisson sigma model presented in arXiv:1503.05625. We show that the consistency of the construction does not impose any further constraints on the differential Poisson algebra geometry than those required for the ungauged model. We conclude by proposing that the gauged model provides a first-quantized framework for higher spin gravity.

  12. 2D Poisson Sigma Models with Gauged Vectorial Supersymmetry

    CERN Document Server

    Bonezzi, Roberto; Torres-Gomez, Alexander

    2015-01-01

    In this note, we gauge the rigid vectorial supersymmetry of the two-dimensional Poisson sigma model presented in arXiv:1503.05625. We show that the consistency of the construction does not impose any further constraints on the differential Poisson algebra geometry than those required for the ungauged model. We conclude by proposing that the gauged model provides a first-quantized framework for higher spin gravity.

  13. A computational definition of the notion of vectorial space

    CERN Document Server

    Arrighi, Pablo

    2009-01-01

    We usually define an algebraic structure by a set, some operations defined on this set and some propositions that the algebraic structure must validate. In some cases, we can replace these propositions by an algorithm on terms constructed upon these operations that the algebraic structure must validate. We show in this note that this is the case for the notions of vectorial space and bilinear operation. KEYWORDS: Rewrite system, vector space, bilinear operation, tensorial product, semantics, quantum programming languages, probabilistic programming languages.

  14. Advanced vectorial simulation of VCSELs with nano structures invited paper

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Mørk, Jesper

    2009-01-01

    The single-mode properties and design issues of three vertical-cavity surface-emitting laser (VCSEL) structures incorporating nano structures are rigorously investigated. Nano structuring enables to deliver selective pumping or loss to the fundamental mode as well as stabilizing the output...... polarization state. Comparison of three vectorial simulation methods reveals that the modal expansion method is suitable for treating the nano structured VCSEL designs....

  15. Vectorial Preisach-type model designed for parallel computing

    Energy Technology Data Exchange (ETDEWEB)

    Stancu, Alexandru [Department of Solid State and Theoretical Physics, Al. I. Cuza University, Blvd. Carol I, 11, 700506 Iasi (Romania)]. E-mail: alstancu@uaic.ro; Stoleriu, Laurentiu [Department of Solid State and Theoretical Physics, Al. I. Cuza University, Blvd. Carol I, 11, 700506 Iasi (Romania); Andrei, Petru [Electrical and Computer Engineering, Florida State University, Tallahassee, FL (United States); Electrical and Computer Engineering, Florida A and M University, Tallahassee, FL (United States)

    2007-09-15

    Most of the hysteresis phenomenological models are scalar, while all the magnetization processes are vectorial. The vector models-phenomenological or micromagnetic (physical)-are time consuming and sometimes difficult to implement. In this paper, we introduce a new vector Preisach-type model that uses micromagnetic results to simulate the magnetic response of a system of several tens of thousands of pseudo-particles. The model has a modular structure that allows easy implementation for parallel computing.

  16. Comparative dynamic analysis of the full Grossman model.

    Science.gov (United States)

    Ried, W

    1998-08-01

    The paper applies the method of comparative dynamic analysis to the full Grossman model. For a particular class of solutions, it derives the equations implicitly defining the complete trajectories of the endogenous variables. Relying on the concept of Frisch decision functions, the impact of any parametric change on an endogenous variable can be decomposed into a direct and an indirect effect. The focus of the paper is on marginal changes in the rate of health capital depreciation. It also analyses the impact of either initial financial wealth or the initial stock of health capital. While the direction of most effects remains ambiguous in the full model, the assumption of a zero consumption benefit of health is sufficient to obtain a definite for any direct or indirect effect.

  17. Eigenvalue analysis using a full-core Monte Carlo method

    Energy Technology Data Exchange (ETDEWEB)

    Okafor, K.C.; Zino, J.F. (Westinghouse Savannah River Co., Aiken, SC (United States))

    1992-01-01

    The reactor physics codes used at the Savannah River Site (SRS) to predict reactor behavior have been continually benchmarked against experimental and operational data. A particular benchmark variable is the observed initial critical control rod position. Historically, there has been some difficulty predicting this position because of the difficulties inherent in using computer codes to model experimental or operational data. The Monte Carlo method is applied in this paper to study the initial critical control rod positions for the SRS K Reactor. A three-dimensional, full-core MCNP model of the reactor was developed for this analysis.

  18. Full-spectrum analysis of natural gamma-ray spectra.

    Science.gov (United States)

    Hendriks, P H; Limburg, J; de Meijer, R J

    2001-01-01

    In this paper, a new system to measure natural gamma-radiation in situ will be presented. This system combines a high-efficiency BGO scintillation detector with full-spectrum data analysis (FSA). This technique uses the (nearly) full spectral shape and the so-called 'standard spectra' to calculate the activity concentrations of 40K, 232Th and 238U present in a geological matrix (sediment, rock, etc.). We describe the FSA and the determination of the standard spectra. Standard spectra are constructed for various geometries and a comparison in intensity and shape will be made. The performance of such a system has been compared to a more traditional system, consisting of a NaI detector in combination with the 'windows' analysis. For count rates typically encountered in field experiments, the same accuracy is obtained 10-20 times faster using the new system. This allows for shorter integration times and hence shorter measurements or a better spatial resolution. The applicability of such a system will be illustrated via an example of an airborne experiment in which the new system produced results comparable to those of much larger traditional systems. This paper will conclude with a discussion of the current status of the system and an outlook for future research.

  19. Microbial community analysis of a full-scale DEMON bioreactor.

    Science.gov (United States)

    Gonzalez-Martinez, Alejandro; Rodriguez-Sanchez, Alejandro; Muñoz-Palazon, Barbara; Garcia-Ruiz, Maria-Jesus; Osorio, Francisco; van Loosdrecht, Mark C M; Gonzalez-Lopez, Jesus

    2015-03-01

    Full-scale applications of autotrophic nitrogen removal technologies for the treatment of digested sludge liquor have proliferated during the last decade. Among these technologies, the aerobic/anoxic deammonification process (DEMON) is one of the major applied processes. This technology achieves nitrogen removal from wastewater through anammox metabolism inside a single bioreactor due to alternating cycles of aeration. To date, microbial community composition of full-scale DEMON bioreactors have never been reported. In this study, bacterial community structure of a full-scale DEMON bioreactor located at the Apeldoorn wastewater treatment plant was analyzed using pyrosequencing. This technique provided a higher-resolution study of the bacterial assemblage of the system compared to other techniques used in lab-scale DEMON bioreactors. Results showed that the DEMON bioreactor was a complex ecosystem where ammonium oxidizing bacteria, anammox bacteria and many other bacterial phylotypes coexist. The potential ecological role of all phylotypes found was discussed. Thus, metagenomic analysis through pyrosequencing offered new perspectives over the functioning of the DEMON bioreactor by exhaustive identification of microorganisms, which play a key role in the performance of bioreactors. In this way, pyrosequencing has been proven as a helpful tool for the in-depth investigation of the functioning of bioreactors at microbiological scale.

  20. Strategies for efficient resolution analysis in full-waveform inversion

    Science.gov (United States)

    Fichtner, A.; van Leeuwen, T.; Trampert, J.

    2016-12-01

    Full-waveform inversion is developing into a standard method in the seismological toolbox. It combines numerical wave propagation for heterogeneous media with adjoint techniques in order to improve tomographic resolution. However, resolution becomes increasingly difficult to quantify because of the enormous computational requirements. Here we present two families of methods that can be used for efficient resolution analysis in full-waveform inversion. They are based on the targeted extraction of resolution proxies from the Hessian matrix, which is too large to store and to compute explicitly. Fourier methods rest on the application of the Hessian to Earth models with harmonic oscillations. This yields the Fourier spectrum of the Hessian for few selected wave numbers, from which we can extract properties of the tomographic point-spread function for any point in space. Random probing methods use uncorrelated, random test models instead of harmonic oscillations. Auto-correlating the Hessian-model applications for sufficiently many test models also characterises the point-spread function. Both Fourier and random probing methods provide a rich collection of resolution proxies. These include position- and direction-dependent resolution lengths, and the volume of point-spread functions as indicator of amplitude recovery and inter-parameter trade-offs. The computational requirements of these methods are equivalent to approximately 7 conjugate-gradient iterations in full-waveform inversion. This is significantly less than the optimisation itself, which may require tens to hundreds of iterations to reach convergence. In addition to the theoretical foundations of the Fourier and random probing methods, we show various illustrative examples from real-data full-waveform inversion for crustal and mantle structure.

  1. Preliminary analysis of knee stress in Full Extension Landing

    Directory of Open Access Journals (Sweden)

    Majid Davoodi Makinejad

    2013-09-01

    Full Text Available OBJECTIVE: This study provides an experimental and finite element analysis of knee-joint structure during extended-knee landing based on the extracted impact force, and it numerically identifies the contact pressure, stress distribution and possibility of bone-to-bone contact when a subject lands from a safe height. METHODS: The impact time and loads were measured via inverse dynamic analysis of free landing without knee flexion from three different heights (25, 50 and 75 cm, using five subjects with an average body mass index of 18.8. Three-dimensional data were developed from computed tomography scans and were reprocessed with modeling software before being imported and analyzed by finite element analysis software. The whole leg was considered to be a fixed middle-hinged structure, while impact loads were applied to the femur in an upward direction. RESULTS: Straight landing exerted an enormous amount of pressure on the knee joint as a result of the body's inability to utilize the lower extremity muscles, thereby maximizing the threat of injury when the load exceeds the height-safety threshold. CONCLUSIONS: The researchers conclude that extended-knee landing results in serious deformation of the meniscus and cartilage and increases the risk of bone-to-bone contact and serious knee injury when the load exceeds the threshold safety height. This risk is considerably greater than the risk of injury associated with walking downhill or flexion landing activities.

  2. Full-Range Public Health Leadership, Part 1: Quantitative Analysis

    Directory of Open Access Journals (Sweden)

    Erik L. Carlton

    2015-04-01

    Full Text Available Background. Workforce and leadership development are central to the future of public health. However, public health has been slow to translate and apply leadership models from other professions and to incorporate local perspectives in understanding public health leadership. Purpose. This study utilized the full-range leadership model in order to examine public health leadership. Specifically, it sought to measure leadership styles among local health department directors and to understand the context of leadership local health departments.Methods. Leadership styles among local health department directors (n=13 were examined using survey methodology. Quantitative analysis methods included descriptive statistics, boxplots, and Pearson bivariate correlations using SPSS v18.0. Findings. Self-reported leadership styles were highly correlated to leadership outcomes at the organizational level. However, they were not related to county health rankings. Results suggest the preeminence of leader behaviors and providing individual consideration to staff as compared to idealized attributes of leaders, intellectual stimulation, or inspirational motivation. Implications. Holistic leadership assessment instruments, such as the Multifactor Leadership Questionnaire (MLQ can be useful in assessing public health leaders approaches and outcomes. Comprehensive, 360-degree reviews may be especially helpful. Further research is needed to examine the effectiveness of public health leadership development models, as well as the extent that public health leadership impacts public health outcomes.

  3. Full text clustering and relationship network analysis of biomedical publications.

    Directory of Open Access Journals (Sweden)

    Renchu Guan

    Full Text Available Rapid developments in the biomedical sciences have increased the demand for automatic clustering of biomedical publications. In contrast to current approaches to text clustering, which focus exclusively on the contents of abstracts, a novel method is proposed for clustering and analysis of complete biomedical article texts. To reduce dimensionality, Cosine Coefficient is used on a sub-space of only two vectors, instead of computing the Euclidean distance within the space of all vectors. Then a strategy and algorithm is introduced for Semi-supervised Affinity Propagation (SSAP to improve analysis efficiency, using biomedical journal names as an evaluation background. Experimental results show that by avoiding high-dimensional sparse matrix computations, SSAP outperforms conventional k-means methods and improves upon the standard Affinity Propagation algorithm. In constructing a directed relationship network and distribution matrix for the clustering results, it can be noted that overlaps in scope and interests among BioMed publications can be easily identified, providing a valuable analytical tool for editors, authors and readers.

  4. Vectorial Control of Magnetization by Light

    CERN Document Server

    Kanda, Natsuki; Shimizu, Hirokatsu; Konishi, Kuniaki; Kuwata-Gonokami, Kosuke Yoshioka And Makoto

    2011-01-01

    Coherent light-matter interactions have recently extended their applications to the ultrafast control of magnetization in solids. An important but unrealized technique is the manipulation of magnetization vector motion to make it follow an arbitrarily designed multi-dimensional trajectory. Furthermore, for its realization, the phase and amplitude of degenerate modes need to be steered independently. A promising method is to employ Raman-type nonlinear optical processes induced by femtosecond laser pulses, where magnetic oscillations are induced impulsively with a controlled initial phase and an azimuthal angle that follows well defined selection rules determined by the materials' symmetries. Here, we emphasize the fact that temporal variation of the polarization angle of the laser pulses enables us to distinguish between the two degenerate modes. A full manipulation of two-dimensional magnetic oscillations is demonstrated in antiferromagnetic NiO by employing a pair of polarization-twisted optical pulses. The...

  5. Álgebra vectorial y geometría euclidiana

    OpenAIRE

    Salazar Caicedo, José Alonso

    1992-01-01

    Las leyes del álgebra vectorial asociadas al conjunto de los segmentos dirigidos del plano (o del espacio), en conexión con un producto interior, permiten demostrar una gran variedad de proposiciones y teoremas de la geometría clásica euclidiana, utilizando procedimientos y técnicas relativamente simples. Desde un punto de vista didáctico y pedagógico, surge el problema de examinar hasta qué punto es posible recuperar gran parte del arsenal de ideas fructíferas que proporcionaban a otras g...

  6. Bioimpedancia vectorial y espectroscópica: valoración del estado de hidratación con ambos métodos en hemodiálisis Bioimpedance vector and spectroscopic analysis: assessing hydration status using both methods in haemodialysis

    OpenAIRE

    Ruth Ros Nogales; Mª Teresa Manso Gil; Gema Palacios García; Jacoba Rodríguez Peña

    2013-01-01

    El análisis de bioimpedancia es una herramienta útil para determinar el estado nutricional y de hidratación del enfermo en hemodiálisis. Los dos sistemas más utilizados son la bioimpedancia de monofrecuencia vectorial y la bioimpedancia multifrecuencia espectroscópica que utilizan diferentes criterios para clasificar el estado de hidratación del enfermo dializado. El sistema de bioimpedancia de monofrecuencia vectorial utiliza una escala ordinal de 7 puntos que va desde el valor 3 (mayor hidr...

  7. Analysis of full-duplex relay networks with opportunistic scheduling

    Directory of Open Access Journals (Sweden)

    Lei Shao

    2015-05-01

    Full Text Available This Letter addresses a two-hop decode-and-forward relay system with full-duplex relaying and opportunistic scheduling. Exact expressions for outage probability, average capacity and symbol error rate are presented in an independent identically distributed Rayleigh fading environment. Numerical and simulated results show the validity of the analytical results.

  8. Vectorial nature of redox Bohr effects in bovine heart cytochrome c oxidase.

    Science.gov (United States)

    Capitanio, N; Capitanio, G; De Nitto, E; Papa, S

    1997-09-08

    The vectorial nature of redox Bohr effects (redox-linked pK shifts) in cytochrome c oxidase from bovine heart incorporated in liposomes has been analyzed. The Bohr effects linked to oxido-reduction of heme a and CuB display membrane vectorial asymmetry. This provides evidence for involvement of redox Bohr effects in the proton pump of the oxidase.

  9. Infrascope: Full-Spectrum Phonocardiography with Automated Signal Analysis Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Using digital signal analysis tools, we will generate a repeatable output from the infrascope and compare it to the output of a traditional electrocardiogram, and...

  10. Full-length genomic analysis of korean porcine sapelovirus strains

    DEFF Research Database (Denmark)

    Son, Kyu-Yeol; Kim, Deok-Song; Kwon, Joseph

    2014-01-01

    the structural features of PSV genomes, the full-length nucleotide sequences of three Korean PSV strains were determined and analyzed using bioinformatic techniques in comparison with other known PSV strains. The Korean PSV genomes ranged from 7,542 to 7,566 nucleotides excluding the 3' poly(A) tail, and showed...

  11. A full simulation analysis of the graviscalar discovery potential

    CERN Document Server

    Oye, Ola Kristoffer

    2005-01-01

    We explore the discovery potential for a graviscalar in ATLAS, using full detector simulation. The graviscalar is an extra dimensional supersymmetric partner to the graviton, arising in the bulk in the ADD scenario. The signal from such a particle will be observed as ETmiss accompanied by a high pT jet. The study is based on a previous study [1] performed with ATLFAST.

  12. Full-Envelope Launch Abort System Performance Analysis Methodology

    Science.gov (United States)

    Aubuchon, Vanessa V.

    2014-01-01

    The implementation of a new dispersion methodology is described, which dis-perses abort initiation altitude or time along with all other Launch Abort System (LAS) parameters during Monte Carlo simulations. In contrast, the standard methodology assumes that an abort initiation condition is held constant (e.g., aborts initiated at altitude for Mach 1, altitude for maximum dynamic pressure, etc.) while dispersing other LAS parameters. The standard method results in large gaps in performance information due to the discrete nature of initiation conditions, while the full-envelope dispersion method provides a significantly more comprehensive assessment of LAS abort performance for the full launch vehicle ascent flight envelope and identifies performance "pinch-points" that may occur at flight conditions outside of those contained in the discrete set. The new method has significantly increased the fidelity of LAS abort simulations and confidence in the results.

  13. The Full Flowpath Analysis of a Hypersonic Vehicle

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A numerical study has been carried out to investigate the full flow path and aerodynamic characteristics of a hypersonic vehicle at a 7.0 free stream Mach number. Results indicate that the inlet started and unstarted operations have remarkable effects on the flow pattern of the full flow path. When the inlet operates in a started mode, the transverse pressure gradient generated by the forebody alters the air captured characteristics and the entering flow quality of the inlet. Furthermore, the expansion process of the nozzle jet flow is obviously affected by the external flow field around the afterbody with the cross section shape transiting from a near rectangle at the exit of the nozzle to a near triangle at the tail of the vehicle. When the inlet operates in an tnstarted mode, the aerodynamic instability can be observed in the full flow path of the vehicle. Due to the oscillation of the external compressed shock wave and nozzle jet flow, the aerodynamic characteristics of the vehicle vary periodically with the lift-drag ratio changing fiom 0.25 to 2.09. Finally, by comparing to the experimental data, the reliability of the CFD is verified.

  14. Full angular analysis of polarized τ → 3 μ decays

    Energy Technology Data Exchange (ETDEWEB)

    Brueser, Robin; Faller, Sven; Feldmann, Thorsten; Lange, Bjoern O.; Mannel, Thomas [Theoretische Elementarteilchenphysik, Naturwissenschaftlich-technische Fakultaet, Universitaet Siegen, 57068 Siegen (Germany); Turczyk, Sascha [PRISMA Cluster of Excellence and Mainz Institut for Theoretical Physics, Johannes Gutenberg University, 55099 Mainz (Germany)

    2015-07-01

    The lepton number violating decay τ → 3 μ is extremely suppressed in the Standard Model and its observation would be direct evidence of New Physics. We investigate the decay of polarized τ leptons in a bottom-up approach using dim 6 operators which respect the symmetries of the Standard Model. We show that useful information can be gained from a polarized initial τ, where the external polarization vector allows for a full angular decomposition of the phase space. Partial rates are then analysed to distinguish models with different helicity structures.

  15. Reflection type metasurface designed for high efficiency vectorial field generation

    Science.gov (United States)

    Wang, Shiyi; Zhan, Qiwen

    2016-07-01

    We propose a reflection type metal-insulator-metal (MIM) metasurface composed of hybrid nano-antennas for comprehensive spatial engineering of the properties of optical fields. The capability of such structure is illustrated in the design of a device that can be used to produce a radially polarized vectorial beam for optical needle field generation. This device consists of uniformly segmented sectors of high efficiency MIM metasurface. With each of the segment sector functioning as a local quarter-wave-plate (QWP), the device is designed to convert circularly polarized incidence into local linear polarization to create an overall radial polarization with corresponding binary phases and extremely high dynamic range amplitude modulation. The capability of such devices enables the generation of nearly arbitrarily complex optical fields that may find broad applications that transcend disciplinary boundaries.

  16. Quantum Efficiency Measurements of Femtosecond Vectorial Photoemission on Cu Photocathodes

    CERN Document Server

    Banfi, F; Galimberti, P G; Giannetti, C; Pagliara, S; Parmigiani, F; Pedersoli, E

    2005-01-01

    Quantum Efficiency (QE) measurements of single photon photoemission from a Cu(111) single crystal and a Cu polycrystal photocathodes, irradiated by 150~fs-6.28~eV laser pulses, are reported over a broad range of incidence angle in both s and p polarizations. The maximum value of QE for the Cu polycrystal sample is Y~4*10(-4), obtained with p polarization at an angle of incidence theta=65°. Our data confirm the vectorial photoemission model. Issues concerning surface roughness and symmetry considerations are addressed. An explanation in terms of non local conductivity tensor is proposed. Advantages of a 6.28~eV photon as compared to the standard 4.71~eV photon in use with Cu photocathodes are discussed.

  17. Vectorial representation of spatial goals in the hippocampus of bats.

    Science.gov (United States)

    Sarel, Ayelet; Finkelstein, Arseny; Las, Liora; Ulanovsky, Nachum

    2017-01-13

    To navigate, animals need to represent not only their own position and orientation, but also the location of their goal. Neural representations of an animal's own position and orientation have been extensively studied. However, it is unknown how navigational goals are encoded in the brain. We recorded from hippocampal CA1 neurons of bats flying in complex trajectories toward a spatial goal. We discovered a subpopulation of neurons with angular tuning to the goal direction. Many of these neurons were tuned to an occluded goal, suggesting that goal-direction representation is memory-based. We also found cells that encoded the distance to the goal, often in conjunction with goal direction. The goal-direction and goal-distance signals make up a vectorial representation of spatial goals, suggesting a previously unrecognized neuronal mechanism for goal-directed navigation.

  18. Evolution of sexual traits influencing vectorial capacity in anopheline mosquitoes

    Science.gov (United States)

    Mitchell, Sara N.; Kakani, Evdoxia G.; South, Adam; Howell, Paul I.; Waterhouse, Robert M.; Catteruccia, Flaminia

    2015-01-01

    The availability of genome sequences from 16 anopheline species provides unprecedented opportunities to study the evolution of reproductive traits relevant for malaria transmission. In Anopheles gambiae, a likely candidate for sexual selection is male 20-hydroxyecdysone (20E). Sexual transfer of this steroid hormone as part of a mating plug dramatically changes female physiological processes intimately tied to vectorial capacity. By combining phenotypic studies with ancestral state reconstructions and phylogenetic analyses, we show that mating plug transfer and male 20E synthesis are both derived characters that have coevolved in anophelines, driving the adaptation of a female 20E-interacting protein that promotes oogenesis via mechanisms also favoring Plasmodium survival. Our data reveal coevolutionary dynamics of reproductive traits between the sexes likely to have shaped the ability of anophelines to transmit malaria. PMID:25722409

  19. Spatial technologies to evaluate vectorial samples quality in maps production

    OpenAIRE

    Abraham Cárdenas Tristán; Eduardo Javier Treviño Garza; Oscar Alberto Aguirre Calderón; Javier Jiménez Pérez; Marco Aurelio González Tagle; Xanat Antonio Némiga

    2013-01-01

    A pesar de importantes progresos realizados en la materia en los últimos años, la conceptualización de la metodología para evaluar la calidad de vectores que integran la cartografía digital es aún una tarea complicada, no existiendo un esquema oficial de evaluación de la calidad de la producción cartográfica vectorial en el país. Se propone una metodología para evaluar la calidad de la producción cartográfica a través del análisis de muestras aplicadas a las diversas escalas vectoriales de la...

  20. Sobre el estado electro-tónico y su interpretación: el potencial vectorial

    Directory of Open Access Journals (Sweden)

    Mauricio Rozo Clavijo

    2015-10-01

    Full Text Available Se presenta un análisis acerca de las perspectivas que surgieron sobre el potencial vectorial a partir de los escritos originales de Faraday y Maxwell. Se muestran las primeras ideas sobre los experimentos y las explicaciones que Faraday desarrolló en torno a la inducción magnética, y la influencia que tuvo su concepto de estado electro-tónico en la primera explicación que formuló Maxwell, quien lo definió como el estado mediante el cual se ejecutan las acciones magnéticas a través de líneas de fuerza. Señala que ese concepto es la base para explicar el fenómeno de la inducción magnética en términos no newtonianos y lo formaliza mediante la variación temporal de la circulación del potencial vectorial a lo largo de una trayectoria cerrada. Este tipo de análisis muestra la manera en que estos pensadores representan el fenómeno, la cual no se evidencia en la literatura, sino que se muestra como una formalización alrededor del campo magnético. On the Electro-Tonic State and its Interpretation: The Vector Potential An analysis is presented on the emerging perspectives about the vector potential from Faraday and Maxwell’s original writings. This paper presents the initial observations about the experiments and explanations developed by Faraday on Magnetic Induction and the influence that his concept of Electrotonic State had on Maxwell’s first explanation. He defined it as the state by which magnetic actions are executed through lines of force. He pointed out that this concept is critical to explain the phenomenon of Magnetic Induction in non-Newtonian terms. Therefore, he formalized it by the circulation of vector potential throughout a closed trajectory. This kind of analysis shows how these researchers represented the phenomenon which is not evident in literature. It’s presented as a formalization around magnetic field instead. Sobre o estado electro-tônica e sua interpretação: o potencial vetor Mostra-se uma an

  1. Full core analysis of IRIS reactor by using MCNPX.

    Science.gov (United States)

    Amin, E A; Bashter, I I; Hassan, Nabil M; Mustafa, S S

    2016-07-01

    This paper describes neutronic analysis for fresh fuelled IRIS (International Reactor Innovative and Secure) reactor by MCNPX code. The analysis included criticality calculations, radial power and axial power distribution, nuclear peaking factor and axial offset percent at the beginning of fuel cycle. The effective multiplication factor obtained by MCNPX code is compared with previous calculations by HELIOS/NESTLE, CASMO/SIMULATE, modified CORD-2 nodal calculations and SAS2H/KENO-V code systems. It is found that k-eff value obtained by MCNPX is closer to CORD-2 value. The radial and axial powers are compared with other published results carried out using SAS2H/KENO-V code. Moreover, the WIMS-D5 code is used for studying the effect of enriched boron in form of ZrB2 on the effective multiplication factor (K-eff) of the fuel pin. In this part of calculation, K-eff is calculated at different concentrations of Boron-10 in mg/cm at different stages of burnup of unit cell. The results of this part are compared with published results performed by HELIOS code.

  2. Gradient Bundle Analysis: A Full Topological Approach to Chemical Bonding

    CERN Document Server

    Morgenstern, Amanda

    2016-01-01

    The "chemical bond" is a central concept in molecular sciences, but there is no consensus as to what a bond actually is. Therefore, a variety of bonding models have been developed, each defining the structure of molecules in a different manner with the goal of explaining and predicting chemical properties. This thesis describes the initial development of gradient bundle analysis (GBA), a chemical bonding model that creates a high resolution picture of chemical interactions within the charge density framework. GBA is based on concepts from the quantum theory of atoms in molecules (QTAIM), but uses a more complete picture of the topology and geometry of the electron charge density to understand and predict bonding interactions. Gradient bundles are defined as volumes bounded by zero-flux surfaces (ZFSs) in the gradient of the charge density with well-defined energies. The structure of gradient bundles provides an avenue for detecting the locations of valence electrons, which correspond to reactive regions in a ...

  3. Full Moment Tensor Analysis at The Geysers Geothermal Field

    Science.gov (United States)

    Boyd, O. S.; Dreger, D. S.; Hellweg, M.; Lombard, P. N.; Ford, S. R.; Taira, T.; Taggart, J.; Weldon, T. J.

    2011-12-01

    Geothermal energy has been produced at The Geysers Geothermal Field in Northern California for more than forty years. It has been demonstrated that increased steam production and fluid injection correlates positively with changes in earthquake activity, resulting in thousands of tiny earthquakes each year with events ranging in magnitude up to 4.5. We determine source parameters for the largest of these earthquakes using a regional distance moment tensor method. We invert three-component, complete waveform data from broadband stations of the Berkeley Digital Seismic Network, the Northern California Seismic Network and the USArray deployment (2005-2007) for the complete, six-element moment tensor. Some solutions depart substantially from a pure double-couple with some events having large volumetric components. Care is needed in the assessment of the significance of the non-double-couple terms. We have worked to develop a systematic procedure for the evaluation of aleatoric and epistemic solution uncertainty (e.g. Ford et al., 2009; Ford et al., 2010). We will present the solutions for The Geysers events together with estimates of random errors and systematic errors due to imperfect station coverage and knowledge of the velocity structure, which are needed to compute Green's functions for the inversion. Preliminary results indicate that some events have large isotropic components that appear to be stable and suggestive of fluid or gas involvement during the rupture processes. We are presently incorporating full moment tensor capability in the Berkeley Seismological Laboratory's automatic processing system and analyst interface. This upgrade will enable improved monitoring at The Geysers and volcanically active regions of California.

  4. Full vector spherical harmonic analysis of the Holocene geomagnetic field

    Science.gov (United States)

    Richardson, Marcia

    High-quality time-series paleomagnetic measurements have been used to derive spherical harmonic models of Earth's magnetic field for the past 2,000 years. A newly-developed data compilation, PSVMOD2.0 consists of time-series directional and intensity records that significantly improve the data quality and global distribution used to develop previous spherical harmonic models. PSVMOD2.0 consists of 185 paleomagnetic time series records from 85 global sites, including 30 full-vector records (inclination, declination and intensity). It includes data from additional sites in the Southern Hemisphere and Arctic and includes globally distributed sediment relative paleointensity records, significantly improving global coverage over previous models. PSVMOD2.0 records have been assessed in a series of 7 regional intercomparison studies, four in the Northern Hemisphere and 3 in the southern hemisphere. Comparisons on a regional basis have improved the quality and chronology of the data and allowed investigation of spatial coherence and the scale length associated with paleomagnetic secular variation (PSV) features. We have developed a modeling methodology based on nonlinear inversion of the PSVMOD2.0 directional and intensity records. Models of the geomagnetic field in 100-year snapshots have been derived for the past 2,000 with the ultimate goal of developing models spanning the past 8,000 years. We validate the models and the methodology by comparing with the GUFM1 historical models during the 400-year period of overlap. We find that the spatial distribution of sites and quality of data are sufficient to derive models that agree with GUFM1 in the large-scale characteristics of the field. We use the the models derived in this study to downward continue the field to the core-mantle boundary and examine characteristics of the large-scale structure of the magnetic field at the source region. The derived models are temporally consistent from one epoch to the next and exhibit

  5. Simplified loss analysis and comparison of full-bridge, full-range-ZVS DC-DC converters

    Indian Academy of Sciences (India)

    Shubhendu Bhardwaj; Mangesh Borage; Sunil Tiwari

    2008-10-01

    The loss of zero-voltage-switching (ZVS) of active switches has been a serious limitation of full-bridge (FBZVS) converters. Many techniques have been proposed in the past to extend the range of ZVS operation over the wider and also the full range of operation. However, in these techniques ZVS is achieved at the expense of additional conduction loss in active switches and losses in the auxiliary components. In this paper, the analysis for the additional losses in various full-range FBZVS DC–DC converters and their comparative evaluation is reported. Closed form expressions are derived for average value of device currents and losses. The loss curves for various topologies are plotted and compared. The analytical results are found to be consistent with the experimental efficiency tests performed on 500 W, 100 kHz prototype. It is concluded that a recently proposed new topology has the least penalty of additional losses.

  6. Compact planetary systems perturbed by an inclined companion: I. Vectorial representation of the secular model

    CERN Document Server

    Boué, Gwenaël

    2014-01-01

    The non-resonant secular dynamics of compact planetary systems are modeled by a perturbing function which is usually expanded in eccentricity and absolute inclination with respect to the invariant plane. Here, the expressions are given in a vectorial form which naturally leads to an expansion in eccentricity and mutual inclination. The two approaches are equivalent in most cases, but the vectorial one is specially designed for those where a quasi-coplanar system tilts as a whole by a large amount. Moreover, the vectorial expressions of the Hamiltonian and of the equations of motion are slightly simpler than those given in terms of the usual elliptical elements. We also provide the secular perturbing function in vectorial form expanded in semimajor axis ratio allowing for arbitrary eccentricities and inclinations. The interaction between the equatorial bulge of a central star and its planets is also provided, as is the relativistic periapse precession of any planet induced by the central star. We illustrate th...

  7. Modelling of photonic-crystal VCSELs with semi-vectorial and vectorial models

    DEFF Research Database (Denmark)

    Dems, Maciej; Chung, Il-Sug; Nyakas, Peter

    2011-01-01

    of the top-mirror DBR or just the VCSEL cavity. The different models are evaluated by comparing the predicted resonance wavelengths and threshold gains for different hole diameters and pitches of the PC. The agreement between the models is relatively good, with an exception of one case, which corresponds...... to the effective index method. The simulation results elucidate the strength and weaknesses of the analyzed methods and outline the limits of applicability of different models.......In the talk the results of the COST MP0702 exercise on modeling photonic- crystal (PC) VCSELs are presented. Four different numerical methods are compared through an analysis of a benchmark VCSEL structure, where the PC structure penetrates all VCSEL layers, the entire top-mirror DBR, a fraction...

  8. High-resolution fully vectorial scanning Kerr magnetometer.

    Science.gov (United States)

    Flajšman, Lukáš; Urbánek, Michal; Křižáková, Viola; Vaňatka, Marek; Turčan, Igor; Šikola, Tomáš

    2016-05-01

    We report on the development of a high-resolution scanning magnetometer, which fully exploits the vectorial nature of the magneto-optical Kerr effect. The three-dimensional nature of magnetization is at the basis of many micromagnetic phenomena and from these data, we can fully characterize magnetization processes of nanostructures in static and dynamic regimes. Our scanning Kerr magnetometer uses a high numerical aperture microscope objective where the incident light beam can be deterministically deviated from the objective symmetry axis, therefore, both in-plane (via the longitudinal Kerr effect) and out-of-plane (via the polar Kerr effect) components of the magnetization vector may be detected. These components are then separated by exploiting the symmetries of the polar and longitudinal Kerr effects. From four consecutive measurements, we are able to directly obtain the three orthogonal components of the magnetization vector with a resolution of 600 nm. Performance of the apparatus is demonstrated by a measurement of 3D magnetization vector maps showing out-of-plane domains and in-plane domain walls in an yttrium-iron-garnet film and on a study of magnetization reversal in a 4-μm-wide magnetic disk.

  9. A vectorial approach to determine frozen orbital conditions

    Science.gov (United States)

    Circi, Christian; Condoleo, Ennio; Ortore, Emiliano

    2017-02-01

    Taking into consideration a probe moving in an elliptical orbit around a celestial body, the possibility of determining conditions which lead to constant values on average of all the orbit elements has been investigated here, considering the influence of the planetary oblateness and the long-term effects deriving from the attraction of several perturbing bodies. To this end, three equations describing the variation of orbit eccentricity, apsidal line and angular momentum unit vector have been first retrieved, starting from a vectorial expression of the Lagrange planetary equations and considering for the third-body perturbation the gravity-gradient approximation, and then exploited to demonstrate the feasibility of achieving the above-mentioned goal. The study has led to the determination of two families of solutions at constant mean orbit elements, both characterised by a co-planarity condition between the eccentricity vector, the angular momentum and a vector resulting from the combination of the orbital poles of the perturbing bodies. As a practical case, the problem of a probe orbiting the Moon has been faced, taking into account the temporal evolution of the perturbing poles of the Sun and Earth, and frozen solutions at argument of pericentre 0° or 180° have been found.

  10. Complex network structure of flocks in the Vicsek Model with Vectorial Noise

    Science.gov (United States)

    Baglietto, Gabriel; Albano, Ezequiel V.; Candia, Julián

    2014-09-01

    In the Vicsek Model (VM), self-driven individuals try to adopt the direction of movement of their neighbors under the influence of noise, thus leading to a noise-driven order-disorder phase transition. By implementing the so-called Vectorial Noise (VN) variant of the VM (i.e. the VM-VN model), this phase transition has been shown to be discontinuous (first-order). In this paper, we perform an extensive complex network study of VM-VN flocks and show that their topology can be described as highly clustered, assortative, and nonhierarchical. We also study the behavior of the VM-VN model in the case of "frozen flocks" in which, after the flocks are formed using the full dynamics, particle displacements are suppressed (i.e. only rotations are allowed). Under this kind of restricted dynamics, we show that VM-VN flocks are unable to support the ordered phase. Therefore, we conclude that the particle displacements at every time-step in the VM-VN dynamics are a key element needed to sustain long-range ordering throughout.

  11. Inter-relation of sylvatic and domestic transmission of Trypanosoma cruzi in areas with and without domestic vectorial transmission in Minas Gerais, Brazil

    Directory of Open Access Journals (Sweden)

    L. Diotaiuti

    1995-08-01

    Full Text Available During the period 1980-1986, we captured triatomine bugs and mammalian reservoir hosts from sylvatic and domestic situations in different municipalities of the State of Minas Gerais. Trypanosoma cruzi was isolated from captured bugs, mammals and patients. After cultivation in LIT medium, the electrophoretic enzyme profiles were determined. We obtained atotal of 32 parasite isolates from regions with active domestic transmission, and 24 isolates form areas under control. For the first areas the results suggest introduction of T. cruzi from sylvatic habitats, through incursion of infected opossums and/or sylvatic T. sordida, which appears to have given rise to at least one acute human infection. Of particular interest is the finding of sylvatic opossums and a T. sordida nymph infected with ZB, that could indicate return of parasites from chronic human infections to sylvatic transmission cycles. For the areas under control we also interpret the results as interaction between sylvatic and domestic cycles of transmission, here through the invasion of houses by bugs carrying the Z1 zymodeme from the sylvatic environment. The Multivariate Correspondence Analysis gives a spatial description between the different parasite isolates and confirms the existence of a bridge in the opposite direction in the region with active vectorial transmission including the exporting of Z2 through the peridomestic environment into the sylvatic cycle. For the others areas this bridge corresponds especially to Panstrongylus megistus, importing Z1 into the domestic environment.

  12. Full-time working couples and their life course : An analysis of leaving full-time employment

    NARCIS (Netherlands)

    Gils, W. van; Kraaykamp, G.; Lippe, T. van der

    2009-01-01

    In the initial phase of family formation a majority of all spouses works full-time. As a result most couples start off as full-time working couples. We used complete career reports of 2.014 couples from the Netherlands to answer the question of which life-course events and individual social resource

  13. Full-time working couples and their life course: An analysis of leaving full-time employment

    NARCIS (Netherlands)

    Kraaykamp, G.L.M.; Gils, W.S. van; Lippe, A.G. van der

    2009-01-01

    In the initial phase of family formation a majority of all spouses works full-time. As a result most couples start off as full-time working couples. We used complete career reports of 2.014 couples from the Netherlands to answer the question of which life-course events and individual social resource

  14. Vectorial coupled-mode solitons in one-dimensional photonic crystals

    Institute of Scientific and Technical Information of China (English)

    朱善华; 黄国翔; 崔维娜

    2002-01-01

    We study the dynamics of vectorial coupled-mode solitons in one-dimensional photonic crystals with quadraticand cubic nonlinearities. Starting from Maxwell's equations, the vectorial coupled-mode equations for the envelopesof two fundamental-frequency optical mode and one low-frequency mode components due to optical rectification arederived by means of the method of multiple scales. A set of coupled soliton solutions of the vectorial coupled-modeequations is provided. The results show that a modulation of the fundamental-frequency optical modes occurs due tothe optical rectification field resulting from the quadratic nonlinearity. The optical rectification field disappears whenthe frequency of the fundamental-frequency optical fields approaches the edge of the photonic bands.

  15. [Vectorial transmission of Chagas' disease in Mulungu do Morro, Northeastern of Brazil].

    Science.gov (United States)

    Aras, Roque; Gomes, Irênio; Veiga, Marielza; Melo, Ailton

    2003-01-01

    A serological survey was carried out to determine the prevalence of Chagas' disease in municipality. The following variables were analyzed to identify the form of transmission of this disease: age, sex, clinical and transfusional history, degree of kinship and serology. Within the 863 municipalities we studied, we identified 265 individuals, with serology testing done on them and on their respective mothers. Of these, 232 tested negative serology for Chagas'disease and 33 (14.2%) positive. We found 9 (3.9%) patients, of 14.3 years. average age with vectorial transmission and 24 (10.3%), of 26.6 years. average age with probable, vertical and vectorial transmission. When we compare the two groups in regard to age averages and manner of transmission of Trypanosoma cruzi, we encounter a statistical significance. Our results suggest the existence of an active, vectorial transmission of Trypanosoma cruzi in Mulungu do Morro.

  16. Application of an approximate vectorial diffraction model to analysing diffractive micro-optical elements

    Institute of Scientific and Technical Information of China (English)

    Niu Chun-Hui; Li Zhi-Yuan; Ye Jia-Sheng; Gu Ben-Yuan

    2005-01-01

    Scalar diffraction theory, although simple and efficient, is too rough for analysing diffractive micro-optical elements.Rigorous vectorial diffraction theory requires extensive numerical efforts, and is not a convenient design tool. In this paper we employ a simple approximate vectorial diffraction model which combines the principle of the scalar diffraction theory with an approximate local field model to analyse the diffraction of optical waves by some typical two-dimensional diffractive micro-optical elements. The TE and TM polarization modes are both considered. We have found that the approximate vectorial diffraction model can agree much better with the rigorous electromagnetic simulation results than the scalar diffraction theory for these micro-optical elements.

  17. CINVEC : Una herramienta multimedial para el análisis vectorial del movimiento

    OpenAIRE

    2005-01-01

    Se presenta el CINVEC, una herramienta multimedia, que facilita la asimilación de los elementos de álgebra vectorial necesarios para comprender y ejercitar contenidos de cinemática correspondientes a la asignatura física de un programa de ingreso de nivel universitario. El alumno reconoce el carácter escalar o vectorial de las distintas magnitudes: posición, desplazamiento, trayectoria, tiempo, velocidad, rapidez, aceleración para finalmente aplicarlas en la descripción de los distintos tipos...

  18. Vectorial Resilient PC(l) of Order k Boolean Functions from AG-Codes

    Institute of Scientific and Technical Information of China (English)

    Hao CHEN; Liang MA; Jianhua LI

    2011-01-01

    Propagation criteria and resiliency of vectorial Boolean functions are important for cryptographic purpose (see [1- 4, 7, 8, 10, 11, 16]). Kurosawa, Stoh [8] and Carlet [1]gave a construction of Boolean functions satisfying PC(l) of order k from binary linear or nonlinear codes. In this paper, the algebraic-geometric codes over GF(2m) are used to modify the Carlet and Kurosawa-Satoh's construction for giving vectorial resilient Boolean functions satisfying PC(l) of order k criterion. This new construction is compared with previously known results.

  19. CINVEC : Una herramienta multimedial para el análisis vectorial del movimiento

    OpenAIRE

    Amato, Marcelo Alejandro; Sosa, María Isabel

    2005-01-01

    Se presenta el CINVEC, una herramienta multimedia, que facilita la asimilación de los elementos de álgebra vectorial necesarios para comprender y ejercitar contenidos de cinemática correspondientes a la asignatura física de un programa de ingreso de nivel universitario. El alumno reconoce el carácter escalar o vectorial de las distintas magnitudes: posición, desplazamiento, trayectoria, tiempo, velocidad, rapidez, aceleración para finalmente aplicarlas en la descripción de los distintos tipos...

  20. Vectorial Nonparaxial Four-Petal Gaussian Beams and Their Propagation in Free Space

    Institute of Scientific and Technical Information of China (English)

    GAO Zeng-Hui; L(U) Bai-Da

    2006-01-01

    @@ The vectorial nonparaxial four-petal Gaussian beam (FPGB) is introduced. The closed-form propagation expressions for the free-space propagation of FPGBs are derived and their more general applicable advantages are illustrated analytically and numerically. Some special interesting cases, in particular the paraxial one, are discussed. It is found that the parameter f = 1/kw0 with the k being the wave number and w0 being the waist width plays a crucial role in determining the nonparaxiallity of FPGBs. For small values of the f parameter the paraxial approximation is allowable. In the nonparaxial regime the beam order n additionally affects the vectorial and nonparaxial behaviour of FPGBs.

  1. Larval food quantity affects development time, survival and adult biological traits that influence the vectorial capacity of Anopheles darlingi under laboratory conditions

    Directory of Open Access Journals (Sweden)

    Araújo Maisa

    2012-08-01

    Full Text Available Abstract Background The incidence of malaria in the Amazon is seasonal and mosquito vectorial capacity parameters, including abundance and longevity, depend on quantitative and qualitative aspects of the larval diet. Anopheles darlingi is a major malaria vector in the Amazon, representing >95% of total Anopheles population present in the Porto Velho region. Despite its importance in the transmission of the Plasmodium parasite, knowledge of the larval biology and ecology is limited. Studies regarding aspects of adult population ecology are more common than studies on larval ecology. However, in order develop effective control strategies and laboratory breeding conditions for this species, more data on the factors affecting vector biology is needed. The aim of the present study is to assess the effects of larval food quantity on the vectorial capacity of An. darling under laboratory conditions. Methods Anopheles darlingi was maintained at 28°C, 80% humidity and exposed to a daily photoperiod of 12 h. Larvae were divided into three experimental groups that were fed either a low, medium, or high food supply (based on the food amounts consumed by other species of culicids. Each experiment was replicated for six times. A cohort of adults were also exposed to each type of diet and assessed for several biological characteristics (e.g. longevity, bite frequency and survivorship, which were used to estimate the vectorial capacity of each experimental group. Results The group supplied with higher food amounts observed a reduction in development time while larval survival increased. In addition to enhanced longevity, increasing larval food quantity was positively correlated with increasing frequency of bites, longer blood meal duration and wing length, resulting in greater vectorial capacity. However, females had greater longevity than males despite having smaller wings. Conclusions Overall, several larval and adult biological traits were significantly

  2. Gaussian beam reflection and refraction by a spherical or parabolic surface: comparison of vectorial-law calculation with lens approximation.

    Science.gov (United States)

    Tkaczyk, Eric R; Mauring, Koit; Tkaczyk, Alan H

    2012-10-01

    A ray-tracing approach is used to demonstrate efficient application of the vectorial laws of reflection and refraction to computational optics problems. Both the full width at half-maximum (fwhm) and offset of Gaussian beams resulting from off-center reflection and refraction are calculated for spherical and paraboloidal surfaces of revolution. It is found that the magnification and displacement depend nonlinearly on the miscentering. For these geometries, the limits of accuracy of the lens approximation are examined quantitatively. In contrast to the ray-tracing solution, this paraxial approximation would predict a magnification of a beam's fwhm that is independent of miscentering, and an offset linearly proportional to the miscentering. The focusing property of paraboloidal surfaces of revolution is also derived in setting up the calculation.

  3. Vectorial nanoscale mapping of optical antenna fields by single molecule dipoles.

    Science.gov (United States)

    Singh, Anshuman; Calbris, Gaëtan; van Hulst, Niek F

    2014-08-13

    Optical nanoantennas confine light on the nanoscale, enabling strong light-matter interactions and ultracompact optical devices. Such confined nanovolumes of light have nonzero field components in all directions (x, y, and z). Unfortunately mapping of the actual nanoscale field vectors has so far remained elusive, though antenna hotspots have been explored by several techniques. In this paper, we present a novel method to probe all three components of the local antenna field. To this end a resonant nanoantenna is fabricated at the vertex of a scanning tip. Next, the nanoantenna is deterministically scanned in close proximity to single fluorescent molecules, whose fixed excitation dipole moment reads out the local field vector. With nanometer molecular resolution, we distinctly map x-, y-, and z-field components of the dipole antenna, i.e. a full vectorial mode map, and show good agreement with full 3D FDTD simulations. Moreover, the fluorescence polarization maps the localized coupling, with emission through the longitudinal antenna mode. Finally, the resonant antenna probe is used for single molecule imaging with 40 nm fwhm response function. The total fluorescence enhancement is 7.6 times, while out-of-plane molecules, almost undetectable in far-field, are made visible by the strong antenna z-field with a fluorescence enhancement up to 100 times. Interestingly, the apparent position of molecules shifts up to 20 nm depending on their orientation. The capability to resolve orientational information on the single molecule level makes the scanning resonant antenna an ideal tool for extreme resolution bioimaging.

  4. Propagation of electromagnetic fields between non-parallel planes: a fully vectorial formulation and an efficient implementation.

    Science.gov (United States)

    Zhang, Site; Asoubar, Daniel; Hellmann, Christian; Wyrowski, Frank

    2016-01-20

    The propagation of electromagnetic fields between non-parallel planes based on a spectrum-of-plane-wave analysis is discussed and formulations for an efficient numerical implementation are presented in detail. It is shown that with the help of interpolation techniques, the numerical implementation can be done with the standard uniform fast Fourier transform (FFT) of easy access. Different interpolation techniques are numerically examined, and it turns out that the use of cubic interpolation, together with the uniform FFT, brings both significantly increased computational efficiency and high simulation accuracy. Apart from the aspect of computational efficiency, all formulations in this work are generalized in a fully vectorial manner in comparison to previous works.

  5. Vectorial beam propagation simulation of a novel polarization conversion waveguide structure

    Science.gov (United States)

    Li, Daoping; van Brug, Hedser H.; Frankena, Hans J.; van der Tol, Jos J.; Pedersen, Jorgen W.

    1995-02-01

    The vectorial beam propagation method has successfully been applied to a passive polarization converting waveguide structure. A complete polarization conversion has been simulated. The propagating fields are calculated and the power attenuation is evaluated. The influence of structural changes of the device on the polarization conversion is investigated.

  6. Assessment of vectorial total variation penalties on realistic dual-energy CT data.

    Science.gov (United States)

    Rigie, David S; Sanchez, Adrian A; La Rivière, Patrick J

    2017-04-21

    Vectorial extensions of total variation have recently been developed for regularizing the reconstruction and denoising of multi-channel images, such as those arising in spectral computed tomography. Early studies have focused mainly on simulated, piecewise-constant images whose structure may favor total-variation penalties. In the current manuscript, we apply vectorial total variation to real dual-energy CT data of a whole turkey in order to determine if the same benefits can be observed in more complex images with anatomically realistic textures. We consider the total nuclear variation ([Formula: see text]) as well as another vectorial total variation based on the Frobenius norm ([Formula: see text]) and standard channel-by-channel total variation ([Formula: see text]). We performed a series of 3D TV denoising experiments comparing the three TV variants across a wide range of smoothness parameter settings, optimizing each regularizer according to a very-high-dose 'ground truth' image. Consistent with the simulation studies, we find that both vectorial TV variants achieve a lower error than the channel-by-channel TV and are better able to suppress noise while preserving actual image features. In this real data study, the advantages are subtler than in the previous simulation study, although the [Formula: see text] penalty is found to have clear advantages over either [Formula: see text] or [Formula: see text] when comparing material images formed from linear combinations of the denoised energy images.

  7. Vectorial capacity of Aedes aegypti for dengue virus type 2 is reduced with co-infection of Metarhizium anisopliae.

    Directory of Open Access Journals (Sweden)

    Javier A Garza-Hernández

    Full Text Available BACKGROUND: Aedes aegypti, is the major dengue vector and a worldwide public health threat combated basically by chemical insecticides. In this study, the vectorial competence of Ae. aegypti co-infected with a mildly virulent Metarhizium anisopliae and fed with blood infected with the DENV-2 virus, was examined. METHODOLOGY/PRINCIPAL FINDINGS: The study encompassed three bioassays (B. In B1 the median lethal time (LT50 of Ae. aegypti exposed to M. anisopliae was determined in four treatments: co-infected (CI, single-fungus infection (SF, single-virus infection (SV and control (C. In B2, the mortality and viral infection rate in midgut and in head were registered in fifty females of CI and in SV. In B3, the same treatments as in B1 but with females separated individually were tested to evaluate the effect on fecundity and gonotrophic cycle length. Survival in CI and SF females was 70% shorter than the one of those in SV and control. Overall viral infection rate in CI and SV were 76 and 84% but the mortality at day six post-infection was 78% (54% infected and 6% respectively. Survivors with virus in head at day seven post-infection were 12 and 64% in both CI and SV mosquitoes. Fecundity and gonotrophic cycle length were reduced in 52 and 40% in CI compared to the ones in control. CONCLUSION/SIGNIFICANCE: Fungus-induced mortality for the CI group was 78%. Of the survivors, 12% (6/50 could potentially transmit DENV-2, as opposed to 64% (32/50 of the SV group, meaning a 5-fold reduction in the number of infective mosquitoes. This is the first report on a fungus that reduces the vectorial capacity of Ae. aegypti infected with the DENV-2 virus.

  8. Modelo Vectorial para la Inferencia del Estado Cognitivo de Pacientes en Estados Derivados del Coma

    Directory of Open Access Journals (Sweden)

    Esteban Velásquez R.

    2014-06-01

    Full Text Available La forma tradicional de evaluar el estado de conciencia de un individuo, ha sido mediante la aplicación de estímulos y el análisis de sus respuestas, sin embargo, esta técnica se ve limitada cuando el individuo es incapaz de responder evidentemente ante un estímulo, como es el caso de los pacientes en estados derivados del coma. En estos casos, se requiere de una conexión directa con el cerebro del paciente para detectar una respuesta. Por consiguiente, en este artículo se desarrolla y analiza un modelo computacional basado en los principios de las máquinas de soporte vectorial (MSV, para inferir el estado cognitivo de pacientes en estados derivados del coma, mediante la utilización de un equipo de electroencefalografía comercial. Los resultados obtenidos, mostraron que el modelo logró clasificar correctamente una tarea cognitiva en al menos cuatro de cada cinco pruebas en pacientes de control, lo que se traduce en la obtención de un sistema de bajo costo para el análisis del estado de conciencia y para la posible comunicación con algunos pacientes en estados derivados del coma mediante protocolos médicos definidos. De esta manera, este sistema se presenta como un gran aporte para las clínicas y centros hospitalarios, como herramienta potencial de diagnóstico para este tipo de pacientes.

  9. Ukraine’s Multi-Vectorial Foreign Policy: Looking West while not Overlooking its Eastern Neighbour

    Directory of Open Access Journals (Sweden)

    María Raquel Freire

    2009-05-01

    Full Text Available La Ucrania post-soviética ha perseguido un curso independiente en su política exterior desde que lograse la independencia en 1991. Sin embargo su posición geográfica condicionó mucho el contorno de su política exterior. De hecho, mientras que un acercamiento al Oeste ha sido valorado grandemente, las relaciones con Rusia han seguido siendo el pilar central de Ucrania, intentándose por tanto, mirar hacia el Oeste sin perder de vista a su vecino oriental. En tal contexto, ¿cómo podrían conciliar las autoridades ucranianas los diferentes vectores de la política exterior de su país?¿En qué medida podrían pervivir los principios de la Revolución Naranja entre un contexto interior tan difícil y un contexto exterior complejo?¿En qué medida pueden afectar a las opciones en política exterior de Kiev la influencia occidental y las interferencias rusas? Intentando encontrar respuestas a tales preguntas, este artículo tiene como objetivo la deconstrucción de los varios círculos en la política exterior multi-vectorial de Kiev que se encargan de atender a la política exterior de una manera integrada y donde las formulaciones interiores se ven condicionadas por las opciones externas, echando luz de esta manera sobre cómo las interrelaciones e interconexiones se desarrollan en el proceso de toma de decisiones y en el curso elegido.

  10. Las funciones de Cobb-Douglas como base del espacio vectorial de funciones homogéneas.

    OpenAIRE

    Díaz Martínez, Zuleyka; Núñez del Prado, José Antonio; García Pineda Mª Pilar

    2003-01-01

    Dado que el conjunto de funciones homogéneas de grado r forma un espacio vectorial real, el objetivo de este trabajo es mostrar que el conjunto de funciones de Cobb- Douglas de grado r, XαYr-α, forma una base de dicho espacio vectorial, lo que puede resultar de interés dada la importancia que las funciones de Cobb- Douglas tienen en Economía.Dado que el conjunto de funciones homogéneas de grado r forma un espacio vectorial real, el objetivo de este trabajo es mostrar que el conjunto de f...

  11. Object oriented Full Function Point Analysis: A Model for Real Time Application

    Directory of Open Access Journals (Sweden)

    Sheeba Praveen

    2012-09-01

    Full Text Available this research work focused on determining the functional size of real time application at early stage. This paper will describe how to estimate the functional size of real time system using OO methodology. In this research we are proposing a Model which is very useful for estimating the size of real time system. And this model is fully based on Object oriented development Methodology due to the adaptation of the Function Point Analysis (FPA to Object Point Analysis (OPA. This model is for Real Time Application due to that have to take the FFP metric because FFP is best for size measurement of real time system. So the mapping is done in between Full Function Point metrics (FFP to Object Oriented Function Point metrics (OOFP and finally we are proposing a new metrics known as OOFFP and the based analysis is known as Object Oriented Full Function Point Analysis (OOFFPA.

  12. Birefringence analysis of segmented cladding fiber.

    Science.gov (United States)

    Kumar, Ajeet; Rastogi, Vipul; Agrawal, Arti; Rahman, B M A

    2012-05-20

    We present a full-vectorial modal analysis of a segmented cladding fiber (SCF). The analysis is based on the H-field vectorial finite element method (VFEM) employing polar mesh geometry. Using this method, we have analyzed the circular SCF and the elliptical SCF. We have found that the birefringence of the circular SCF is very small (1.0×10(-8)). Birefringence of a highly elliptical SCF can be altered to some extent by the number of segments and duty cycle of segmentation in the segmented cladding. However, the change is not profound. The analysis shows that the circular SCF possesses low birefringence and that the segmented cladding does not add any significant birefringence in an elliptical fiber. This result strongly indicates that small deviations in the segmented cladding parameters arising from fabrication process do not significantly affect the birefringence of the fiber.

  13. The vectorial photoelectric effect under solar irradiance and its application to sun sensing

    CERN Document Server

    Hechenblaikner, Gerald

    2014-01-01

    Sun sensors are an integral part of the attitude and orbit control system onboard almost any spacecraft. While the majority of standard analogue sun sensors is based on photo-detectors which produce photo-currents proportional to the cosine of the incidence angle (cosine detectors), we propose an alternative scheme where the vectorial photoelectric effect is exploited to achieve a higher sensitivity of the sensed photo-current to the incidence angle. The vectorial photo-effect is investigated in detail for metal cathode detectors in a space environment. Besides long operational lifetimes without significant degradation, metal cathode detectors are insensitive to earth albedo, which may significantly reduce the errors affecting attitude measurements in low earth orbits. Sensitivity curves are calculated and trade-offs performed with the aim of optimizing the sensitivity whilst also providing currents sufficient for detection. Simple applications and detector configurations are also discussed and compared to ex...

  14. Vectorial laws of refraction and reflection using the cross product and dot product.

    Science.gov (United States)

    Tkaczyk, Eric R

    2012-03-01

    We demonstrate that published vectorial laws of reflection and refraction of light based solely on the cross product do not, in general, uniquely determine the direction of the reflected and refracted waves without additional information. This is because the cross product does not have a unique inverse operation, which is explained in this Letter in linear algebra terms. However, a vector is in fact uniquely determined if both the cross product (vector product) and dot product (scalar product) with a known vector are specified, which can be written as a single equation with a left-invertible matrix. It is thus possible to amend the vectorial laws of reflection and refraction to incorporate both the cross and dot products for a complete specification with unique solution. This enables highly efficient, unambiguous computation of reflected and refracted wave vectors from the incident wave and surface normal. © 2012 Optical Society of America

  15. LOPES 3D - vectorial measurements of radio emission from cosmic ray induced air showers

    CERN Document Server

    Apel, W D; Bähren, L; Bekk, K; Bertaina, M; Biermann, P L; Blümer, J; Bozdog, H; Brancus, I M; Chiavassa, A; Daumiller, K; de Souza, V; Di Pierro, F; Doll, P; Engel, R; Falcke, H; Fuchs, B; Fuhrmann, D; Gemmeke, H; Grupen, C; Haungs, A; Heck, D; Hörandel, J R; Horneffer, A; Huber, D; Huege, T; Isar, P G; Kampert, K -H; Kang, D; Krömer, O; Kuijpers, J; Link, K; Luczak, P; Ludwig, M; Mathes, H J; Melissas, M; Morello, C; Oehlschläger, J; Palmieri, N; Pierog, T; Rautenberg, J; Rebel, H; Roth, M; Rühle, C; Saftoiu, A; Schieler, H; Schmidt, A; Schröder, F G; Sima, O; Toma, G; Trinchero, G C; Weindl, A; Wochele, J; Zabierowski, J; Zensus, J A

    2013-01-01

    LOPES 3D is able to measure all three components of the electric field vector of the radio emission from air showers. This allows a better comparison with emission models. The measurement of the vertical component increases the sensitivity to inclined showers. By measuring all three components of the electric field vector LOPES 3D demonstrates by how much the reconstruction accuracy of primary cosmic ray parameters increases. Thus LOPES 3D evaluates the usefulness of vectorial measurements for large scale applications.

  16. Vectorially oriented monolayers of the cytochrome c/cytochrome oxidase bimolecular complex.

    OpenAIRE

    Edwards, A M; Blasie, J. K.; Bean, J. C.

    1998-01-01

    Vectorially oriented monolayers of yeast cytochrome c and its bimolecular complex with bovine heart cytochrome c oxidase have been formed by self-assembly from solution. Both quartz and Ge/Si multilayer substrates were chemical vapor deposited with an amine-terminated alkylsiloxane monolayer that was then reacted with a hetero-bifunctional cross-linking reagent, and the resulting maleimide endgroup surface then provided for covalent interactions with the naturally occurring single surface cys...

  17. Interaction of light with the polarization devices: a vectorial Pauli algebraic approach

    Energy Technology Data Exchange (ETDEWEB)

    Tudor, Tiberiu [Faculty of Physics, University of Bucharest, PO Box MG-11, 0771253, Bucharest-Magurele (Romania)], E-mail: ttudor@ifin.nipne.ro

    2008-10-17

    A theoretical approach to the interaction between polarized light and polarization devices, based on the vectorial and pure operatorial form of the Pauli algebra, is presented. Unlike the standard (Jones and Mueller) approaches, this formalism is coordinate-free, i.e. it does not appeal to any matrix representation of the involved operators. This vectorial approach establishes a mathematical bridge between the Hilbert space of the density operators of the polarization states and the Poincare space of their geometric representations and gives a rigorous justification of the handling of the interactions between the polarization states and polarization systems on the Poincare sphere (in the Poincare ball). In such an approach, unlike the standard ones, the three relevant quantities that characterize the interaction-the gain, the Poincare vector of the outgoing light and its degree of polarization-result straightforwardly, in block, in the Pauli vectorial expressions of the density operator of the output state. The final equations are symmetric, compact and physically expressive. A generalized form of Malus' law, for any dichroic device and partially polarized light is obtained this way.

  18. Full cost accounting in the analysis of separated waste collection efficiency: A methodological proposal.

    Science.gov (United States)

    D'Onza, Giuseppe; Greco, Giulio; Allegrini, Marco

    2016-02-01

    Recycling implies additional costs for separated municipal solid waste (MSW) collection. The aim of the present study is to propose and implement a management tool - the full cost accounting (FCA) method - to calculate the full collection costs of different types of waste. Our analysis aims for a better understanding of the difficulties of putting FCA into practice in the MSW sector. We propose a FCA methodology that uses standard cost and actual quantities to calculate the collection costs of separate and undifferentiated waste. Our methodology allows cost efficiency analysis and benchmarking, overcoming problems related to firm-specific accounting choices, earnings management policies and purchase policies. Our methodology allows benchmarking and variance analysis that can be used to identify the causes of off-standards performance and guide managers to deploy resources more efficiently. Our methodology can be implemented by companies lacking a sophisticated management accounting system.

  19. Dispersion characteristics of optically excited coplanar striplines - Comprehensive full-wave analysis

    Science.gov (United States)

    Phatak, Dhananjay S.; Defonzo, A. P.; Das, Nirod K.

    1990-11-01

    A comprehensive full-wave formulation is developed to evaluate the dispersion and losses for coplanar striplines on substrates of finite and infinite thicknesses is presented. The loss mechanisms incorporated in the analysis are substrate losses and dielectric material losses. The method of Das and Pozar (1987) is generalized to include a complex propagation vector and can be used over a wide frequency range. A large range of line dimensions can also be handled, limits being set by the accuracy of the moment method. Metal losses can also be incorporated into this analysis by applying the appropriate boundary conditions for lossy metal. Analytically, the excitation of substrate modes is shown to correspond to the occurrence of the poles of the Green function in the reaction integrals. Results of the full-wave analysis are in good agreement with those obtained by established theory.

  20. Do animals bite more during a full moon? Retrospective observational analysis.

    Science.gov (United States)

    Bhattacharjee, C; Bradley, P; Smith, M; Scally, A J; Wilson, B J

    To test the hypothesis that the incidence of animal bites increases at the time of a full moon. Retrospective observational analysis. Accident and emergency department at a general hospital in an English city. 1621 consecutive patients, irrespective of age and sex. Number of patients who attended an accident and emergency department during 1997 to 1999 after being bitten by an animal. The number of bites in each day was compared with the lunar phase in each month. The incidence of animal bites rose significantly at the time of a full moon. With the period of the full moon as the reference period, the incidence rate ratio of the bites for all other periods of the lunar cycle was significantly lower (P full moon is associated with a significant increase in animal bites to humans.

  1. Throughput Analysis of Full Duplex Communication with Asymmetric Traffic in Small Cell Systems

    DEFF Research Database (Denmark)

    Mahmood, Nurul Huda; Berardinelli, Gilberto; Mogensen, Preben Elgaard;

    2015-01-01

    in this contribution using network analysis tools from stochastic geometry. The analytical findings are further confirmed through computer-based Monte-Carlo simulations. Asymmetric downlink/uplink traffic pattern and the increased network interference stemming from full duplex transmissions are found to limit its......Full duplex communication promises a 100% throughput gain by enabling simultaneous transmission and reception. However, such simultaneous communication leads to a corresponding increase in the network interference. In addition, full duplex communication can only be exploited when traffic...... is available in both uplink and downlink directions; while, cellular network traffic tend to be downlink heavy in practice. The potential throughput gains of full duplex communication over conventional half duplex transmission in a small cell network with asymmetric traffic conditions are investigated...

  2. Full-Band Quasi-Harmonic Analysis and Synthesis of Musical Instrument Sounds with Adaptive Sinusoids

    Directory of Open Access Journals (Sweden)

    Marcelo Caetano

    2016-05-01

    Full Text Available Sinusoids are widely used to represent the oscillatory modes of musical instrument sounds in both analysis and synthesis. However, musical instrument sounds feature transients and instrumental noise that are poorly modeled with quasi-stationary sinusoids, requiring spectral decomposition and further dedicated modeling. In this work, we propose a full-band representation that fits sinusoids across the entire spectrum. We use the extended adaptive Quasi-Harmonic Model (eaQHM to iteratively estimate amplitude- and frequency-modulated (AM–FM sinusoids able to capture challenging features such as sharp attacks, transients, and instrumental noise. We use the signal-to-reconstruction-error ratio (SRER as the objective measure for the analysis and synthesis of 89 musical instrument sounds from different instrumental families. We compare against quasi-stationary sinusoids and exponentially damped sinusoids. First, we show that the SRER increases with adaptation in eaQHM. Then, we show that full-band modeling with eaQHM captures partials at the higher frequency end of the spectrum that are neglected by spectral decomposition. Finally, we demonstrate that a frame size equal to three periods of the fundamental frequency results in the highest SRER with AM–FM sinusoids from eaQHM. A listening test confirmed that the musical instrument sounds resynthesized from full-band analysis with eaQHM are virtually perceptually indistinguishable from the original recordings.

  3. Experimental and Theoretical Modal Analysis of Full-Sized Wood Composite Panels Supported on Four Nodes

    Science.gov (United States)

    Guan, Cheng; Zhang, Houjiang; Wang, Xiping; Miao, Hu; Zhou, Lujing; Liu, Fenglu

    2017-01-01

    Key elastic properties of full-sized wood composite panels (WCPs) must be accurately determined not only for safety, but also serviceability demands. In this study, the modal parameters of full-sized WCPs supported on four nodes were analyzed for determining the modulus of elasticity (E) in both major and minor axes, as well as the in-plane shear modulus of panels by using a vibration testing method. The experimental modal analysis was conducted on three full-sized medium-density fiberboard (MDF) and three full-sized particleboard (PB) panels of three different thicknesses (12, 15, and 18 mm). The natural frequencies and mode shapes of the first nine modes of vibration were determined. Results from experimental modal testing were compared with the results of a theoretical modal analysis. A sensitivity analysis was performed to identify the sensitive modes for calculating E (major axis: Ex and minor axis: Ey) and the in-plane shear modulus (Gxy) of the panels. Mode shapes of the MDF and PB panels obtained from modal testing are in a good agreement with those from theoretical modal analyses. A strong linear relationship exists between the measured natural frequencies and the calculated frequencies. The frequencies of modes (2, 0), (0, 2), and (2, 1) under the four-node support condition were determined as the characteristic frequencies for calculation of Ex, Ey, and Gxy of full-sized WCPs. The results of this study indicate that the four-node support can be used in free vibration test to determine the elastic properties of full-sized WCPs. PMID:28773043

  4. Harmonic Analysis of Offshore Wind Farms with Full Converter Wind Turbines

    DEFF Research Database (Denmark)

    Kocewiak, Lukasz Hubert; Hjerrild, Jesper; Bak, Claus Leth

    2009-01-01

    This paper presents the harmonic analysis of offshore wind farm (OWF) models with full converters represented as harmonic sources and measurement data on the point of common coupling (PCC) during normal operation. The model describes a wind farm (WF) with full rated converters installed connected....... Simulation results are compared with representative measurement data obtained from measurement campaign done in an OWF situated in United Kingdom. The problems and limitations related to present standards and practice will be discussed based on measurements from offshore wind farm....

  5. Theoretical analysis of the kinetic performance of laboratory- and full-scale composting systems.

    Science.gov (United States)

    Baptista, Marco; Silveira, Ana; Antunes, Fernando

    2012-07-01

    Composting research at laboratory-scale is critical for the development of optimized full-scale plants. Discrepancies between processes at laboratory-scale and full-scale systems have been investigated in terms of heat balances, but a kinetic analysis of this issue is still missing. In this study, the composting rate at laboratory-scale was, on average, between 1.9 and 5.7 times faster than in full-scale systems for a set of published studies using municipal solid waste, food waste or similar materials. Laboratory-scale performance and full-scale systems were limited to 71 and 46%, respectively, of their maximum potential due to poor management of environmental process conditions far from their optimum. The main limiting environmental factor was found to be moisture content, followed by temperature. Besides environmental factors, waste composition and particle size were identified as factors accounting for kinetic differences between laboratory- and full-scale systems. Overall, this study identifies those factors that affect the kinetics of the composting process most and revealed a significant margin for reducing process time in full-scale composting.

  6. Small-Signal Stability Analysis of Full-Load Converter Interfaced Wind Turbines

    DEFF Research Database (Denmark)

    Knüppel, Thyge; Akhmatov, Vladislav; Nielsen, Jørgen Nygård

    2009-01-01

    Power system stability investigations of wind farms often cover the tasks of low-voltage-fault-ride-through, voltage and reactive power control, and power balancing, but not much attention has yet been paid to the task of small-signal stability. Small-signal stability analysis needs increasing...... focus since the share of wind power increases substituting power generation from conventional power plants. Here, a study based on modal analysis is presented which investigate the effect of large scale integration of full-load converter interfaced wind turbines on inter-area oscillations in a three...

  7. Thermal analysis of both ventilated and full disc brake rotors with frictional heat generation

    Directory of Open Access Journals (Sweden)

    Belhocine A.

    2014-06-01

    Full Text Available In automotive engineering, the safety aspect has been considered as a number one priority in development of a new vehicle. Each single system has been studied and developed in order to meet safety requirements. Instead of having air bags, good suspension systems, good handling and safe cornering, one of the most critical systems in a vehicle is the brake system. The objective of this work is to investigate and analyze the temperature distribution of rotor disc during braking operation using ANSYS Multiphysics. The work uses the finite element analysis techniques to predict the temperature distribution on the full and ventilated brake discs and to identify the critical temperature of the rotor. The analysis also gives us the heat flux distribution for the two discs.

  8. A note on the robustness of a full Bayesian method for nonignorable missing data analysis

    OpenAIRE

    Zhang, Zhiyong; Wang,Lijuan

    2012-01-01

    A full Bayesian method utilizing data augmentation and Gibbs sampling algorithms is presented for analyzing nonignorable missing data. The discussion focuses on a simplified selection model for regression analysis. Regardless of missing mechanisms, it is assumed that missingness only depends on the missing variable itself. Simulation results demonstrate that the simplified selection model can recover regression model parameters under both correctly specified situations and many misspecified s...

  9. Full factorial design analysis of carbon nanotube polymer-cement composites

    Directory of Open Access Journals (Sweden)

    Fábio de Paiva Cota

    2012-08-01

    Full Text Available The work described in this paper is related to the effect of adding carbon nanotubes (CNT on the mechanical properties of polymer-cement composites. A full factorial design has been performed on 160 samples to identify the contribution provided by the following factors: polymeric phase addition, CNT weight addition and water/cement ratio. The response parameters of the full factorial design were the bulk density, apparent porosity, compressive strength and elastic modulus of the polymer-cement-based nanocomposites. All the factors considered in this analysis affected significantly the bulk density and apparent porosity of the composites. The compressive strength and elastic modulus were affected primarily by the cross-interactions between polymeric phase and CNT additions, and the water/cement ratio with polymeric phase factors.

  10. Full-observability analysis and implementation of the general SLAM model

    Science.gov (United States)

    Souici, Ae.; Courdesses, M.; Ouldali, A.; Chatila, R.

    2013-03-01

    Simultaneous localisation and mapping (SLAM) problem is a non-linear system with dynamic state and measurement dimensions. The full observability of such system was ignored, in spite of the fact that system observability is a fundamental aspect in any state estimation problem. In this article, we present a full observability analysis of the general SLAM model. We show that known landmarks (anchor) solution does not guarantee full observability. Furthermore, we prove that to make the general SLAM model fully observable, a combination of known landmarks and invariant metrics are needed. Moreover, we propose a solution to implement a fully observable SLAM model based on mature landmark and virtual observation concepts. Simulations and experimental results are presented demonstrating the validity of the solutions in real world.

  11. Quantitative analysis of multiple components based on liquid chromatography with mass spectrometry in full scan mode.

    Science.gov (United States)

    Xu, Min Li; Li, Bao Qiong; Wang, Xue; Chen, Jing; Zhai, Hong Lin

    2016-08-01

    Although liquid chromatography with mass spectrometry in full scan mode can obtain all the signals simultaneously in a large range and low cost, it is rarely used in quantitative analysis due to several problems such as chromatographic drifts and peak overlap. In this paper, we propose a Tchebichef moment method for the simultaneous quantitative analysis of three active compounds in Qingrejiedu oral liquid based on three-dimensional spectra in full scan mode of liquid chromatography with mass spectrometry. After the Tchebichef moments were calculated directly from the spectra, the quantitative linear models for three active compounds were established by stepwise regression. All the correlation coefficients were more than 0.9978. The limits of detection and limits of quantitation were less than 0.11 and 0.49 μg/mL, respectively. The intra- and interday precisions were less than 6.54 and 9.47%, while the recovery ranged from 102.56 to 112.15%. Owing to the advantages of multi-resolution and inherent invariance properties, Tchebichef moments could provide favorable results even in the situation of peaks shifting and overlapping, unknown interferences and noise signals, so it could be applied to the analysis of three-dimensional spectra in full scan mode of liquid chromatography with mass spectrometry.

  12. Predicción de la estructura secundaria de proteínas usando Máquinas de soporte Vectorial

    Directory of Open Access Journals (Sweden)

    Darío José Delgado

    2012-04-01

    Full Text Available Normal 0 21 false false false ES-CO X-NONE X-NONE MicrosoftInternetExplorer4 Título en ingles: Protein secondary structure prediction    using  support vector machines Abstract : Among the computational methods used for predicting secondary structure proteins highlights the use of support vector machines. This research shows the predicted secondary structure of protein from its primary amino acid sequence using Support Vector Machines. As inputs, in the proposed methodology, features are used from different structural motifs or text strings associated with the primary structure which represents the secondary structure, such as R-group and the probability that the amino acid at position adopts a central particular secondary structure. For feature extraction method is used coding of sequences in which each symbol in the primary structure is associated with each symbol in the secondary structure. The use of this encoding method reduces the dimensionality of the data of thousands of characteristics only 220 of these. The results obtained are comparable to those reported in the literature, taking about 70% accuracy. Furthermore, it is possible to reduce computational cost in the construction of classifiers because this work models the problem of multi classification as a group of binary classifiers. Key words: coding methodology; support vector machines; prediction of protein secondary structure. Resumen: Entre los métodos computacionales utilizados para la predicción de la estructura secundaria de proteínas, se destaca el uso de máquinas de soporte vectorial. Este trabajo de investigación presenta la predicción de la estructura secundaria de proteínas desde su secuencia primaria de aminoácidos usando Máquinas de Soporte Vectorial. Como entradas, en la metodología propuesta, se utilizan características de los diferentes motivos estructurales o cadenas de texto asociadas a la estructura primaria que representa la estructura secundaria

  13. An integrated factor analysis model for product eco-design based on full life cycle assessment

    Directory of Open Access Journals (Sweden)

    Zhi fang Zhou

    2016-02-01

    Full Text Available Purpose: Among the methods of comprehensive analysis for a product or an enterprise, there exist defects and deficiencies in traditional standard cost analyses and life cycle assessment methods. For example, some methods only emphasize one dimension (such as economic or environmental factors while neglecting other relevant dimensions. This paper builds a factor analysis model of resource value flow, based on full life cycle assessment and eco-design theory, in order to expose the relevant internal logic between these two factors. Design/methodology/approach: The model considers the efficient multiplication of resources, economic efficiency, and environmental efficiency as its core objectives. The model studies the status of resource value flow during the entire life cycle of a product, and gives an in-depth analysis on the mutual logical relationship of product performance, value, resource consumption, and environmental load to reveal the symptoms and potentials in different dimensions. Originality/value: This provides comprehensive, accurate and timely decision-making information for enterprise managers regarding product eco-design, as well as production and management activities. To conclude, it verifies the availability of this evaluation and analysis model using a Chinese SUV manufacturer as an example. 

  14. Desarrollar el pensamiento científico de las ciencias naturales en Física para el análisis vectorial de fuerza.

    OpenAIRE

    Campus Lemus, Diana Ivonne; Díaz Moreno, Gabriela Fabiola; Espinosa Moya, Wendy Sofía; Guerrero Barajas, Marcela Margarita; Leal Leyva, Milagros Berenice

    2012-01-01

    1)Información general 2)Evaluación diagnóstica 3) Temario: Tema 1. ¿Cómo se conceptualiza la competencia de análisis vectorial? Tema 2. ¿Por qué es relevante la competencia de análisis vectorial de fuerzas? Tema 3. ¿Cómo aprendo la competencia para el análisis vectorial de fuerzas? Tema 4. ¿Cómo aplico la competencia de análisis vectorial de fuerzas? Tema...

  15. Experimental Analysis and Full Prediction Model of a 5-DOF Motorized Spindle

    Directory of Open Access Journals (Sweden)

    Weiyu Zhang

    2017-01-01

    Full Text Available The cost and power consumption of DC power amplifiers are much greater than that of AC power converters. Compared to a motorized spindle supported with DC magnetic bearings, a motorized spindle supported with AC magnetic bearings is inexpensive and more efficient. This paper studies a five-degrees-of-freedom (5-DOF motorized spindle supported with AC hybrid magnetic bearings (HMBs. Most models of suspension forces, except a “switching model”, are quite accurate, but only in a particular operating area and not in regional coverage. If a “switching model” is applied to a 5-DOF motorized spindle, the real-time performance of the control system can be significantly decreased due to the large amount of data processing for both displacement and current. In order to solve this defect, experiments based on the “switching model” are performed, and the resulting data are analyzed. Using the data analysis results, a “full prediction model” based on the operating state is proposed to improve real-time performance and precision. Finally, comparative, verification and stiffness tests are conducted to verify the improvement of the proposed model. Results of the tests indicate that the rotor has excellent characteristics, such as good real-time performance, superior anti-interference performance with load and the accuracy of the model in full zone. The satisfactory experimental results demonstrate the effectiveness of the “full prediction model” applied to the control system under different operating stages. Therefore, the results of the experimental analysis and the proposed full prediction model can provide a control system of a 5-DOF motorized spindle with the most suitable mathematical models of the suspension force.

  16. 3D Vectorial Time Domain Computational Integrated Photonics

    Energy Technology Data Exchange (ETDEWEB)

    Kallman, J S; Bond, T C; Koning, J M; Stowell, M L

    2007-02-16

    microchip laser logic devices as well as devices characterized by electromagnetic (EM) propagation in nonlinear materials with time-varying parameters. The deliverables for this project were extended versions of the laser logic device code Quench2D and the EM propagation code EMsolve with new modules containing the novel solutions incorporated by taking advantage of the existing software interface and structured computational modules. Our approach was multi-faceted since no single methodology can always satisfy the tradeoff between model runtime and accuracy requirements. We divided the problems to be solved into two main categories: those that required Full Wave Methods and those that could be modeled using Approximate Methods. Full Wave techniques are useful in situations where Maxwell's equations are not separable (or the problem is small in space and time), while approximate techniques can treat many of the remaining cases.

  17. Vectorial Formalism of Polyphase Synchronous Machine With Permanents Magnets

    Directory of Open Access Journals (Sweden)

    Nacéra Bachir Bouiadjra

    2013-04-01

    Full Text Available This paper presents a mathematical model that transforms the real machine to fictitious machines and our goal is to simulate these and see the behavior of these machines in load. The polyphase machines are developed mainly in the field of variable speed drives of high power because increasing the number of phases on the one hand allows to reduce the dimensions of the components in power modulators energy and secondly to improve the operating safety. By a vector approach (vector space, it is possible to find a set of single-phase machine and / or two-phase fictitious equivalent to polyphase synchronous machine. These fictitious machines are coupled electrically and mechanically but decoupled magnetically. This approach leads to introduce the concept of the equivalent machine (multimachine multiconverter system MMS which aims to analyze systems composed of multiple machines (or multiple converters in electric drives. A first classification multimachine multiconverter system follows naturally from MMS formalism. We present an example of a pentaphase (polyphase synchronous machine for a simulation and study the behavior of the machine load

  18. Effect of Larval Competition on Extrinsic Incubation Period and Vectorial Capacity of Aedes albopictus for Dengue Virus.

    Science.gov (United States)

    Bara, Jeffrey; Rapti, Zoi; Cáceres, Carla E; Muturi, Ephantus J

    2015-01-01

    Despite the growing awareness that larval competition can influence adult mosquito life history traits including susceptibility to pathogens, the net effect of larval competition on human risk of exposure to mosquito-borne pathogens remains poorly understood. We examined how intraspecific larval competition affects dengue-2 virus (DENV-2) extrinsic incubation period and vectorial capacity of its natural vector Aedes albopictus. Adult Ae. albopictus from low and high-larval density conditions were orally challenged with DENV-2 and then assayed for virus infection and dissemination rates following a 6, 9, or 12-day incubation period using real-time quantitative reverse transcription PCR. We then modeled the effect of larval competition on vectorial capacity using parameter estimates obtained from peer-reviewed field and laboratory studies. Larval competition resulted in significantly longer development times, lower emergence rates, and smaller adults, but did not significantly affect the extrinsic incubation period of DENV-2 in Ae. albopictus. Our vectorial capacity models suggest that the effect of larval competition on adult mosquito longevity likely has a greater influence on vectorial capacity relative to any competition-induced changes in vector competence. Furthermore, we found that large increases in the viral dissemination rate may be necessary to compensate for small competition-induced reductions in daily survivorship. Our results indicate that mosquito populations that experience stress from larval competition are likely to have a reduced vectorial capacity, even when susceptibility to pathogens is enhanced.

  19. The stability analysis of the full velocity and acceleration velocity model

    Science.gov (United States)

    Xiaomei, Zhao; Ziyou, Gao

    2007-03-01

    The stability analysis is one of the important problems in the traffic flow theory, since the congestion phenomena can be regarded as the instability and the phase transition of a dynamical system. Theoretically, we analyze the stable conditions of the full velocity and acceleration difference model (FVADM), which is proposed by introducing the acceleration difference term based on the previous car-following models (the optimal velocity model and the full velocity difference model, OVM and FVDM). By numerical simulations, it is found that when the traffic flow is unstable, the traffic jam in the FVADM is weaker than that in the FVDM. Also it is observed that the spreading speed of the jam is slower in the FVADM than that in the FVDM and the fluctuations of vehicles in the FVADM are smaller than those in the FVDM. Therefore, the acceleration difference term has strong effects on traffic dynamics and plays an important role in stabilizing the traffic flow.

  20. Third generation sfermions decays into Z and W gauge bosons: full one-loop analysis

    CERN Document Server

    Arhrib, A; Arhrib, Abdesslam; Benbrik, Rachid

    2004-01-01

    The complete one-loop radiative corrections to third generation scalar fermions into gauge bosons Z and W^\\pm is considered. We focus on \\wt{f}_2 \\to Z \\wt{f}_1 and \\wt{f}_i \\to W^\\pm \\wt{f'}_1 (f,f'=t,b). We include both SUSY-QCD, QED and full electroweak corrections. It is found that the electroweak corrections can be of the same order as the SUSY-QCD corrections. The two sets of corrections interfere destructively in some region of parameter space. The full one loop correction can reach 10% in some SUGRA scenario, while in model independent analysis like general MSSM, the one loop correction can reach 20% for large \\tan\\beta and large trilinear soft breaking terms A_b.

  1. Linealización de sistemas VSC-HVDC para el diseño de un controlador PI vectorial

    Directory of Open Access Journals (Sweden)

    Nelson Díaz Aldana

    2014-01-01

    Full Text Available Los sistemas VSC-HVDC son muy utilizados para la transmisión de energía en redes de interconexión eléctrica. Uno de los principales problemas que poseen estos sistemas es la complejidad de su modelo matemático, lo que conlleva grandes dificultades para el diseño de controladores que permitan la regulación de parámetros como la tensión DC de transmisión, así como la potencia activa y reactiva del sistema VSC-HVDC. En este artículo se presenta la linealización de un sistema VSC-HVDC y el posterior diseño de un controlador lineal PI vectorial a partir del modelo linealizado. Adicionalmente, se proponen dos estrategias para la validación de este tipo de controladores, la primera consiste en un único controlador PI para regular los estados del sistema para cada VSC, la segunda consiste en el diseño de controladores PI vectoriales independientes para la regulación de cada estado del VSC.

  2. HARDI DATA DENOISING USING VECTORIAL TOTAL VARIATION AND LOGARITHMIC BARRIER

    Science.gov (United States)

    Kim, Yunho; Thompson, Paul M.; Vese, Luminita A.

    2010-01-01

    In this work, we wish to denoise HARDI (High Angular Resolution Diffusion Imaging) data arising in medical brain imaging. Diffusion imaging is a relatively new and powerful method to measure the three-dimensional profile of water diffusion at each point in the brain. These images can be used to reconstruct fiber directions and pathways in the living brain, providing detailed maps of fiber integrity and connectivity. HARDI data is a powerful new extension of diffusion imaging, which goes beyond the diffusion tensor imaging (DTI) model: mathematically, intensity data is given at every voxel and at any direction on the sphere. Unfortunately, HARDI data is usually highly contaminated with noise, depending on the b-value which is a tuning parameter pre-selected to collect the data. Larger b-values help to collect more accurate information in terms of measuring diffusivity, but more noise is generated by many factors as well. So large b-values are preferred, if we can satisfactorily reduce the noise without losing the data structure. Here we propose two variational methods to denoise HARDI data. The first one directly denoises the collected data S, while the second one denoises the so-called sADC (spherical Apparent Diffusion Coefficient), a field of radial functions derived from the data. These two quantities are related by an equation of the form S = SSexp (−b · sADC) (in the noise-free case). By applying these two different models, we will be able to determine which quantity will most accurately preserve data structure after denoising. The theoretical analysis of the proposed models is presented, together with experimental results and comparisons for denoising synthetic and real HARDI data. PMID:20802839

  3. Full-Length High-Temperature Severe Fuel Damage Test No. 5: Final safety analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lanning, D.D.; Lombardo, N.J.; Panisko, F.E.

    1993-09-01

    This report presents the final safety analysis for the preparation, conduct, and post-test discharge operation for the Full-Length High Temperature Experiment-5 (FLHT-5) to be conducted in the L-24 position of the National Research Universal (NRU) Reactor at Chalk River Nuclear Laboratories (CRNL), Ontario, Canada. The test is sponsored by an international group organized by the US Nuclear Regulatory Commission. The test is designed and conducted by staff from Pacific Northwest Laboratory with CRNL staff support. The test will study the consequences of loss-of-coolant and the progression of severe fuel damage.

  4. Full-Band Monte Carlo Analysis of Hot-Carrier Light Emission in GaAs

    Science.gov (United States)

    Ferretti, I.; Abramo, A.; Brunetti, R.; Jacobini, C.

    1997-11-01

    A computational analysis of light emission from hot carriers in GaAs due to direct intraband conduction-conduction (c-c) transitions is presented. The emission rates have been evaluated by means of a Full-Band Monte-Carlo simulator (FBMC). Results have been obtained for the emission rate as a function of the photon energy, for the emitted and absorbed light polarization along and perpendicular to the electric field direction. Comparison has been made with available experimental data in MESFETs.

  5. EXACTITUD ESPACIAL EN LA CREACIÓN DE BASES DE DATOS SIG MODELOS RÁSTER Y VECTORIAL SPATIAL ACCURACY IN THE CREATION OF DATABASES GIS RASTER AND VECTOR MODELS

    Directory of Open Access Journals (Sweden)

    Carlos Mena Frau

    2008-06-01

    Full Text Available La exactitud en la representación espacial de elementos geográficos en una base de datos de un Sistema de Información Geográfica (SIG está sujeta a errores originados en los procesos de captura y procesamiento de los datos, lo cual queda en evidencia cuando se integra información más exacta. La cuantificación del error es fundamental cuando se pretende tomar decisiones sobre la base de la información disponible. En el estudio se establece una metodología para determinar y comparar el error de representación de elementos geográficos en los modelos vectorial y ráster. La base de datos incluye elementos puntuales, lineales y poligonales, que representan elementos reales correspondientes a una torre, un camino y un rodal. Esta información se obtuvo a partir de mediciones en terreno con el Sistema de Posicionamiento Global (GPS, que fueron procesadas para dar origen a coberturas en formato vectorial. Posteriormente, se realizó el traspaso de la información al formato ráster, empleando resoluciones de píxel de 5, 10 y 20 metros. Mediante un algoritmo matemático se determinaron coordenadas homólogas entre los elementos representados en los dos modelos. De la distancia euclidiana entre coordenadas homólogas, se obtuvo un error medio de representación para cada modelo que luego se utilizó para hacer un análisis estadístico de comparación de exactitud espacial entre los modelos. Los resultados obtenidos indican que no existen diferencias significativas en el error medio de los modelos vectorial y ráster, pero sí existen diferencias en los errores medios arrojados para las distintas resoluciones empleadas en la rasterización de la información original.Representation spatial accuracy of geographic elements in a Geographic Information System (GIS database is subject to errors generated in the processes of data capture and processing, which is in evidence when more exact information is integrated. Error quantification is

  6. Thermohydraulic incidents at full power (safety analysis detailed report no. 1)

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-15

    In this paper, attention is focused on the role of plant-incident analysis during the design stage and the conclusions reached regarding safety. This class of incidents includes sequences arising from the breakdown or anomalous behaviour of components or from errors in plant operation that have repercussions on the process of the system involved and the related systems. The sequences of possible relevance to safety are those which stress the active and passive protection (containment barriers). As these stresses are below the design-basis limits, they have no consequences in terms of radioactivity release. This report illustrates in greater detail the analysis that led to this conclusion, with particular reference to reactor events that have significant consequences on the first barrier (fuel cladding). Thermohydraulic incidents at full power are examined here.

  7. Derivada parcial de un campo vectorial respecto de una variable escalar

    OpenAIRE

    Macho Ortiz, Andrés

    2014-01-01

    Derivar un campo vectorial respecto una variable escalar (por ejemplo el tiempo o la frecuencia) no es nada evidente. Hay un momento en que nos encontramos con la necesidad de derivar los vectores unitarios de la base del sistema de coordenadas respecto de esa variable escalar. Si trabajamos con coordenadas cilíndricas o esféricas dicha derivada no tiene por qué ser nula y hay que calcularla, que es lo difícil del asunto. Para poder calcularla habrá que hacer un cálculo tedioso qu...

  8. Derivada parcial de un campo vectorial respecto de una variable escalar

    OpenAIRE

    Macho Ortiz, Andrés

    2014-01-01

    Derivar un campo vectorial respecto una variable escalar (por ejemplo el tiempo o la frecuencia) no es nada evidente. Hay un momento en que nos encontramos con la necesidad de derivar los vectores unitarios de la base del sistema de coordenadas respecto de esa variable escalar. Si trabajamos con coordenadas cilíndricas o esféricas dicha derivada no tiene por qué ser nula y hay que calcularla, que es lo difícil del asunto. Para poder calcularla habrá que hacer un cálculo tedioso qu...

  9. Biological cycle and preliminary data on vectorial competence of Triatoma boliviana in laboratory conditions.

    Science.gov (United States)

    Durán, Pamela; Siñani, Edda; Depickère, Stéphanie

    2014-12-01

    With more than 140 potential vectors of Chagas disease, it is important to better know the biology and especially the vectorial capacity of the triatomine species which live in the surroundings of human dwellings. In Bolivia where 17 triatomine species are reported, the principal vector is Triatoma infestans. In some valleys of the department of La Paz where T. infestans is not present, a new species (Triatoma boliviana) was described in 2007. This species lives in a sylvatic environment not far away from the dwellings, and occasionally some individuals are found inside the houses. This study was carried out to describe the biological cycle of T. boliviana and to determine its vectorial competence. The development of a cohort of 95 nymphs of first instar (N1) was followed through nymphal instars and adult stage until death in laboratory (22°C). They were fed twice a week on an immobilized mouse. The median egg-to-adult development time was 8.4 months. The mortality by nymphal instar was lower than 7% except for N1 (67%) and N5 (18%). All nymph instars needed at least two feedings to molt (until six feedings for N5). The differentiation of a nymph into a female or a male could not be detected until the fifth instar for which the food intake was greater for a nymph developing into a female. Adults fed about once a week. The adult life span was around 400 days. The fecundity was 4.2 eggs/female/week, with a hatching rate of 50% and a hatching time of 39 days. In the same conditions, T. infestans showed a similar fecundity but a greater hatching rate and hatching time. A trial for rearing the adults at a higher temperature (26°C) showed a drastic fall in the fecundity and in the hatching rate. The vectorial competence was analyzed for fifth instars and adults by three parameters: the ability to feed on human beings, the capacity to be infected by T. cruzi and the postfeeding defecation delay. Results showed a relatively high vectorial competence: (1) insects fed

  10. Vectorial magnetometry and anisotropy studies on thin Co{sub 50}Fe{sub 50} films using MOKE

    Energy Technology Data Exchange (ETDEWEB)

    Kuschel, Timo; Wollschlaeger, Joachim [Fachbereich Physik, Universitaet Osnabrueck, Barbarastr. 7, 49069 Osnabrueck (Germany); Hamrle, Jaroslav; Pistora, Jaromir [Department of Physics, VSB - Technical University of Ostrava, 17. listopadu 15, 70833 Ostrava-Poruba (Czech Republic); Bosu, Subrojati; Sakuraba, Yuya; Takanashi, Koki [Institute for Materials Research (IMR), Tohoku University, Katahira 2-1-1, Aoba-ku, Sendai 980-8577 (Japan)

    2011-07-01

    Magnetooptical Kerr effect (MOKE) is a powerful tool to determine magnetic properties of thin magnetic films. In some cases this technique is only applied to detect magnetization curves qualitatively. In order to perform a quantitative analysis we present MOKE measurements with s- and p-polarized incident light, using an external magnetic field either parallel or perpendicular to the plane of incidence of light and different orientations of the crystalline substrate. The processing of the data includes vectorial magnetometry as well as studies of the anisotropy constants and magnetic axes. The investigated Co{sub 50}Fe{sub 50} films o f 50 nm thickness on MgO(001) are prepared with different annealing temperatures (RT up to 400 C). On the one hand the films with lower annealing tempe ratures show typical magnetic reversal processes of samples with four-fold symmetry as expected for cubic crystal structures. On the other hand the film annealed at 400 C presents an additional strong in-plane anisotropy, which is discussed in context of a classical free energy approach.

  11. Technical Data to Justify Full Burnup Credit in Criticality Safety Licensing Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Enercon Services, Inc.

    2011-03-14

    ENERCON's understanding of the difficult issues related to obtaining and analyzing additional cross section test data to support Full Burnup Credit. A PIRT (Phenomena Identification and Ranking Table) analysis was performed by ENERCON to evaluate the costs and benefits of acquiring different types of nuclear data in support of Full Burnup Credit. A PIRT exercise is a formal expert elicitation process with the final output being the ranking tables. The PIRT analysis (Table 7-4: Results of PIRT Evaluation) showed that the acquisition of additional Actinide-Only experimental data, although beneficial, was associated with high cost and is not necessarily needed. The conclusion was that the existing Radiochemical Assay (RCA) data plus the French Haut Taux de Combustion (HTC)2 and handbook Laboratory Critical Experiment (LCE) data provide adequate benchmark validation for Actinide-Only Burnup Credit. The PIRT analysis indicated that the costs and schedule to obtain sufficient additional experimental data to support the addition of 16 fission products to Actinide-Only Burnup Credit to produce Full Burnup Credit are quite substantial. ENERCON estimates the cost to be $50M to $100M with a schedule of five or more years. The PIRT analysis highlights another option for fission product burnup credit, which is the application of computer-based uncertainty analyses (S/U - Sensitivity/Uncertainty methodologies), confirmed by the limited experimental data that is already available. S/U analyses essentially transform cross section uncertainty information contained in the cross section libraries into a reactivity bias and uncertainty. Recent work by ORNL and EPRI has shown that a methodology to support Full Burnup Credit is possible using a combination of traditional RCA and LCE validation plus S/U validation for fission product isotopics and cross sections. Further, the most recent cross section data (ENDF/B-VII) can be incorporated into the burnup credit codes at a reasonable cost

  12. Integrative microbial community analysis reveals full-scale enhanced biological phosphorus removal under tropical conditions

    Science.gov (United States)

    Law, Yingyu; Kirkegaard, Rasmus Hansen; Cokro, Angel Anisa; Liu, Xianghui; Arumugam, Krithika; Xie, Chao; Stokholm-Bjerregaard, Mikkel; Drautz-Moses, Daniela I.; Nielsen, Per Halkjær; Wuertz, Stefan; Williams, Rohan B. H.

    2016-05-01

    Management of phosphorus discharge from human waste is essential for the control of eutrophication in surface waters. Enhanced biological phosphorus removal (EBPR) is a sustainable, efficient way of removing phosphorus from waste water without employing chemical precipitation, but is assumed unachievable in tropical temperatures due to conditions that favour glycogen accumulating organisms (GAOs) over polyphosphate accumulating organisms (PAOs). Here, we show these assumptions are unfounded by studying comparative community dynamics in a full-scale plant following systematic perturbation of operational conditions, which modified community abundance, function and physicochemical state. A statistically significant increase in the relative abundance of the PAO Accumulibacter was associated with improved EBPR activity. GAO relative abundance also increased, challenging the assumption of competition. An Accumulibacter bin-genome was identified from a whole community metagenomic survey, and comparative analysis against extant Accumulibacter genomes suggests a close relationship to Type II. Analysis of the associated metatranscriptome data revealed that genes encoding proteins involved in the tricarboxylic acid cycle and glycolysis pathways were highly expressed, consistent with metabolic modelling results. Our findings show that tropical EBPR is indeed possible, highlight the translational potential of studying competition dynamics in full-scale waste water communities and carry implications for plant design in tropical regions.

  13. System analysis of a bio-energy plantation: full greenhouse gas balance and energy accounting (POPFULL)

    Science.gov (United States)

    Ceulemans, R.; Janssens, I.; Berhongaray, G.; Broeckx, L.; De Groote, T.; ElKasmioui, O.; Fichot, R.; Njakou Djomo, S.; Verlinden, M.; Zona, D.

    2011-12-01

    In recent year the environmental impact of fossil fuels and their reduced availability are leading to an increasing interest in renewable energy sources, among them bio-energy. However, the cost/benefit in establishing, managing, and using these plantations for energy production should be quantified together with their environmental impact. In this project we are performing a full life cycle analysis (LCA) balance of the most important greenhouse gases (CO2, CH4, N2O, H2O and O3), together with full energy accounting of a short-rotation coppice (SRC) plantation with fast-growing trees. We established the plantation two years ago and we have been monitoring net fluxes of CO2, N2O, CH4, and O3, in combination with biomass pools (incl. soil) and fluxes, and volatile organic carbon (VOCs). This poplar plantation will be monitored for another two years then harvested and transformed into bio-energy. For the energy accounting we are performing a life cycle analysis and energy efficiency assessments over the entire cycle of the plantation until the production of electricity and heat. Here we present an overview of the results from the first two years from the plantation establishment, and some of the projections based on these first results.

  14. Full-field optical coherence tomography for the analysis of fresh unstained human lobectomy specimens

    Directory of Open Access Journals (Sweden)

    Manu Jain

    2013-01-01

    Full Text Available Background: Full-field optical coherence tomography (FFOCT is a real-time imaging technique that generates high-resolution three-dimensional tomographic images from unprocessed and unstained tissues. Lack of tissue processing and associated artifacts, along with the ability to generate large-field images quickly, warrants its exploration as an alternative diagnostic tool. Materials and Methods: One section each from the tumor and from adjacent non-neoplastic tissue was collected from 13 human lobectomy specimens. They were imaged fresh with FFOCT and then submitted for routine histopathology. Two blinded pathologists independently rendered diagnoses based on FFOCT images. Results: Normal lung architecture (alveoli, bronchi, pleura and blood vessels was readily identified with FFOCT. Using FFOCT images alone, the study pathologists were able to correctly identify all tumor specimens and in many cases, the histological subtype of tumor (e.g., adenocarcinomas with various patterns. However, benign diagnosis was provided with high confidence in roughly half the tumor-free specimens (others were diagnosed as equivocal or false positive. Further analysis of these images revealed two major confounding features: (a Extensive lung collapse and (b presence of smoker′s macrophages. On a closer inspection, however, the smoker′s macrophages could often be identified as distinct from tumor cells based on their relative location in the alveoli, size and presence of anthracosis. We posit that greater pathologist experience, complemented with morphometric analysis and color-coding of image components, may help minimize the contribution of these confounders in the future. Conclusion: Our study provides evidence for the potential utility of FFOCT in identifying and differentiating lung tumors from non-neoplastic lung tissue. We foresee its potential as an adjunct to intra-surgical frozen section analysis for margin assessment, especially in limited lung

  15. Analysis of full-waveform LiDAR pulse properties for vegetation discrimination and characterisation

    Science.gov (United States)

    Fieber, K.; Davenport, I.; Ferryman, J.; Gurney, R.; Walker, J.; Hacker, J.

    2012-04-01

    Accurate information about vegetation/forest structure, health and growth is needed in many fields of forest management, environmental planning, resource management, fire risk assessment and soil moisture retrievals. Airborne laser scanning has proven over the last nearly two decades to be an invaluable tool in describing vegetation and providing 3D information about its structure. In particular, the new generation full-waveform laser scanners offer an excellent source of not only accurate XYZ information, but also allow the extraction of additional parameters in the process of light curve analysis and interpretation. This analysis was carried out on full-waveform airborne LiDAR data that was collected with a Riegl LMS-Q560 instrument in the Yanco area (NSW) in Australia. The initial analysis was performed on the data acquired in 2006 during the National Airborne Field Experiment. The way the waveform data was extracted made it impossible for the targets included in the footprint to be geo-coded accurately. Nevertheless it was still possible to analyse the waveforms' shapes. For the purpose of this experiment two test sites were chosen - one very small site covering only a single Eucalyptus tree, and the second over an orange orchard (218m by 110m). Analysis included peaks detection, pulse width calculation and waveforms classification according to the number of peaks present within them. Subsequently, an amplitude-width analysis was carried out, including two-tailed t-tests, histograms and scatter plots. Based on the assumption that the first and middle returns were from vegetation (due to specifics of the sites), it was concluded from the analysis that vegetation returns are wide and weak (wider than emitted pulse). The scatter plots of amplitude versus width according to the pulse type played a crucial role in the analysis - they clearly indicated different 'fingerprints' of vegetation and last return (assumed to be a mixture of vegetation and ground returns

  16. Adaptive automatic data analysis in full-field fringe-pattern-based optical metrology

    Science.gov (United States)

    Trusiak, Maciej; Patorski, Krzysztof; Sluzewski, Lukasz; Pokorski, Krzysztof; Sunderland, Zofia

    2016-12-01

    Fringe pattern processing and analysis is an important task of full-field optical measurement techniques like interferometry, digital holography, structural illumination and moiré. In this contribution we present several adaptive automatic data analysis solutions based on the notion of Hilbert-Huang transform for measurand retrieval via fringe pattern phase and amplitude demodulation. The Hilbert-Huang transform consists of 2D empirical mode decomposition algorithm and Hilbert spiral transform analysis. Empirical mode decomposition adaptively dissects a meaningful number of same-scale subimages from the analyzed pattern - it is a data-driven method. Appropriately managing this set of unique subimages results in a very powerful fringe pre-filtering tool. Phase/amplitude demodulation is performed using Hilbert spiral transform aided by the local fringe orientation estimator. We describe several optical measurement techniques for technical and biological objects characterization basing on the especially tailored Hilbert-Huang algorithm modifications for fringe pattern denoising, detrending and amplitude/phase demodulation.

  17. Analysis Platform for Energy Efficiency Enhancement in Hybrid and Full Electric Vehicles

    Directory of Open Access Journals (Sweden)

    NICOLAICA, M.-O.

    2016-02-01

    Full Text Available The current paper presents a new virtual analysis method that is applied both on hybrid and electric vehicle architectures with the purpose of contributing to the improvement of energy efficiency. The study is based on Matlab modeling and simulation. A set of parameters are considered in order to assess the system performance. The benefit is given by the comparative overview obtained after the completed analysis. The effectiveness of the analysis method is confirmed by a sequence of simulation results combined in several case studies. The impulse of the research is given by the fact that the automotive market is focusing on wider simulation techniques and better control strategies that lead to more efficient vehicles. Applying the proposed method during design would improve the battery management and controls strategy. The advantage of this method is that the system behavior with regards to energy efficiency can be evaluated from an early concept phase. The results contribute to the actual necessity of driving more efficient and more environmental friendly vehicles.

  18. Skin cancer margin analysis within minutes with full-field OCT (Conference Presentation)

    Science.gov (United States)

    Dalimier, Eugénie; Ogrich, Lauren; Morales, Diego; Cusack, Carrie Ann; Abdelmalek, Mark; Boccara, Claude; Durkin, John

    2017-02-01

    Non-melanoma skin cancer (NMSC) is the most common cancer. Treatment consists of surgical removal of the skin cancer. Traditional excision involves the removal of the visible skin cancer with a significant margin of normal skin. On cosmetically sensitive areas, Mohs micrographic tissue is the standard of care. Mohs uses intraoperative microscopic margin assessment which minimizes the surgical defect and can help reduce the recurrence rate by a factor of 3. The current Mohs technique relies on frozen section tissue slide preparation which significantly lengthens operative time and requires on-site trained histotechnicians. Full-Field Optical Coherence Tomography (FFOCT) is a novel optical imaging technique which provides a quick and efficient method to visualize cancerous areas in minutes, without any preparation or destruction of the tissue. This study aimed to evaluate the potential of FFOCT for the analysis of skin cancer margins during Mohs surgery. Over 150 images of Mohs specimens were acquired intraoperatively with FFOCT before frozen section analysis. The imaging procedure took less than 5 minutes for each specimen. No artifacts on histological preparation were found arising from FFOCT manipulation; however frozen section artifact was readily seen on FFOCT. An atlas was established with FFOCT images and corresponding histological slides to reveal FFOCT reading criteria of normal and cancerous structures. Blind analysis showed high concordance between FFOCT and histology. FFOCT can potentially reduce recurrence rates while maintaining short surgery times, optimize clinical workflow, and decrease healthcare costs. For the patient, this translates into smaller infection risk, decreased stress, and better comfort.

  19. Global sensitivity analysis in the identification of cohesive models using full-field kinematic data

    KAUST Repository

    Alfano, Marco

    2015-03-01

    Failure of adhesive bonded structures often occurs concurrent with the formation of a non-negligible fracture process zone in front of a macroscopic crack. For this reason, the analysis of damage and fracture is effectively carried out using the cohesive zone model (CZM). The crucial aspect of the CZM approach is the precise determination of the traction-separation relation. Yet it is usually determined empirically, by using calibration procedures combining experimental data, such as load-displacement or crack length data, with finite element simulation of fracture. Thanks to the recent progress in image processing, and the availability of low-cost CCD cameras, it is nowadays relatively easy to access surface displacements across the fracture process zone using for instance Digital Image Correlation (DIC). The rich information provided by correlation techniques prompted the development of versatile inverse parameter identification procedures combining finite element (FE) simulations and full field kinematic data. The focus of the present paper is to assess the effectiveness of these methods in the identification of cohesive zone models. In particular, the analysis is developed in the framework of the variance based global sensitivity analysis. The sensitivity of kinematic data to the sought cohesive properties is explored through the computation of the so-called Sobol sensitivity indexes. The results show that the global sensitivity analysis can help to ascertain the most influential cohesive parameters which need to be incorporated in the identification process. In addition, it is shown that suitable displacement sampling in time and space can lead to optimized measurements for identification purposes.

  20. Aplicaciones del dibujo vectorial a la creación gráfica contemporánea

    OpenAIRE

    Villagrán Arroyal, Inmaculada Lucía

    2016-01-01

    La tesis “Aplicaciones del dibujo vectorial a la creación gráfica contemporánea” es el resultado de una minuciosa investigación que agrupa los referentes históricos, descriptivos y técnicos, así como algunos de los medios y aplicaciones prácticas que definen, en todo su conjunto, la técnica digital para el dibujo conocida como vectorial. Esta investigación transcurre desde los primeros gráficos reconocidos como vectoriales, recorriendo el camino de la revolución digital que justifica el orige...

  1. Full quantitative phase analysis of hydrated lime using the Rietveld method

    Energy Technology Data Exchange (ETDEWEB)

    Lassinantti Gualtieri, Magdalena, E-mail: magdalena.gualtieri@unimore.it [Dipartimento Ingegneria dei Materiali e dell' Ambiente, Universita Degli Studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41100 Modena (Italy); Romagnoli, Marcello; Miselli, Paola; Cannio, Maria [Dipartimento Ingegneria dei Materiali e dell' Ambiente, Universita Degli Studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41100 Modena (Italy); Gualtieri, Alessandro F. [Dipartimento di Scienze della Terra, Universita Degli Studi di Modena e Reggio Emilia, I-41100 Modena (Italy)

    2012-09-15

    Full quantitative phase analysis (FQPA) using X-ray powder diffraction and Rietveld refinements is a well-established method for the characterization of various hydraulic binders such as Portland cement and hydraulic limes. In this paper, the Rietveld method is applied to hydrated lime, a non-hydraulic traditional binder. The potential presence of an amorphous phase in this material is generally ignored. Both synchrotron radiation and a conventional X-ray source were used for data collection. The applicability of the developed control file for the Rietveld refinements was investigated using samples spiked with glass. The results were cross-checked by other independent methods such as thermal and chemical analyses. The sample microstructure was observed by transmission electron microscopy. It was found that the consistency between the different methods was satisfactory, supporting the validity of FQPA for this material. For the samples studied in this work, the amount of amorphous material was in the range 2-15 wt.%.

  2. Video analysis of dust events in full-tungsten ASDEX Upgrade

    Science.gov (United States)

    Brochard, F.; Shalpegin, A.; Bardin, S.; Lunt, T.; Rohde, V.; Briançon, J. L.; Pautasso, G.; Vorpahl, C.; Neu, R.; The ASDEX Upgrade Team

    2017-03-01

    Fast video data recorded during seven consecutive operation campaigns (2008-2012) in full-tungsten ASDEX Upgrade have been analyzed with an algorithm developed to automatically detect and track dust particles. A total of 2425 discharges have been analyzed, corresponding to 12 204 s of plasma operation. The analysis aimed at precisely identifying and sorting the discharge conditions responsible of the dust generation or remobilization. Dust rates are found to be significantly lower than in tokamaks with carbon PFCs. Significant dust events occur mostly during off-normal plasma phases such as disruptions and particularly those preceded by vertical displacement events (VDEs). Dust rates are also increased but to a lower extent during type-I ELMy H-modes. The influences of disruption energy, heating scenario, vessel venting and vessel vibrations are also presented.

  3. Comparative analysis of full genomic sequences among different genotypes of dengue virus type 3

    Directory of Open Access Journals (Sweden)

    Lin Ting-Hsiang

    2008-05-01

    Full Text Available Abstract Background Although the previous study demonstrated the envelope protein of dengue viruses is under purifying selection pressure, little is known about the genetic differences of full-length viral genomes of DENV-3. In our study, complete genomic sequencing of DENV-3 strains collected from different geographical locations and isolation years were determined and the sequence diversity as well as selection pressure sites in the DENV genome other than within the E gene were also analyzed. Results Using maximum likelihood and Bayesian approaches, our phylogenetic analysis revealed that the Taiwan's indigenous DENV-3 isolated from 1994 and 1998 dengue/DHF epidemics and one 1999 sporadic case were of the three different genotypes – I, II, and III, each associated with DENV-3 circulating in Indonesia, Thailand and Sri Lanka, respectively. Sequence diversity and selection pressure of different genomic regions among DENV-3 different genotypes was further examined to understand the global DENV-3 evolution. The highest nucleotide sequence diversity among the fully sequenced DENV-3 strains was found in the nonstructural protein 2A (mean ± SD: 5.84 ± 0.54 and envelope protein gene regions (mean ± SD: 5.04 ± 0.32. Further analysis found that positive selection pressure of DENV-3 may occur in the non-structural protein 1 gene region and the positive selection site was detected at position 178 of the NS1 gene. Conclusion Our study confirmed that the envelope protein is under purifying selection pressure although it presented higher sequence diversity. The detection of positive selection pressure in the non-structural protein along genotype II indicated that DENV-3 originated from Southeast Asia needs to monitor the emergence of DENV strains with epidemic potential for better epidemic prevention and vaccine development.

  4. Analysis of interferences from full energy peaks in gamma spectrometry of NORM and TENORM samples

    Directory of Open Access Journals (Sweden)

    Živanović Miloš Z.

    2012-01-01

    Full Text Available A considerable number of primordial radioisotopes are present in almost all the samples extracted from the Earth’s crust, such as oil, rock, soil or other materials. Their concentrations are often determined by gamma spectrometry. Although the relative concentrations of isotopes often fluctuate within a narrow range, it is not always the case. Some natural materials (such as naturally occurring radioactive material show unusual activity ratio between 238U and 232Th, while technologically processed materials (technologically enhanced naturally occurring radioactive material might also introduce significant disequilibrium in radioactive chains. Knowing that primordial radioisotopes emit in total more than a thousand gamma and characteristic X-ray photons and that many of them interfere with each other, a question arises whether for some activity ratios commonly used photopeaks become useless for quantitative analysis, due to interferences with other photopeaks. A computer program was developed in order to calculate full energy photon interferences for any chosen photopeak. The calculations are based on the inputs in the form of isotope activities and detector calibration equations and its characteristics are presented in this paper. [Projekat Ministarstva nauke Republike Srbije, br. III43009

  5. Agricultural Land Classification Based on Statistical Analysis of Full Polarimetric SAR Data

    Science.gov (United States)

    Mahdian, M.; Homayouni, S.; Fazel, M. A.; Mohammadimanesh, F.

    2013-09-01

    The discrimination capability of Polarimetric Synthetic Aperture Radar (PolSAR) data makes them a unique source of information with a significant contribution in tackling problems concerning environmental applications. One of the most important applications of these data is land cover classification of the earth surface. These data type, make more detailed classification of phenomena by using the physical parameters and scattering mechanisms. In this paper, we have proposed a contextual unsupervised classification approach for full PolSAR data, which allows the use of multiple sources of statistical evidence. Expectation-Maximization (EM) classification algorithm is basically performed to estimate land cover classes. The EM algorithm is an iterative algorithm that formalizes the problem of parameters estimation of a mixture distribution. To represent the statistical properties and integrate contextual information of the associated image data in the analysis process we used Markov random field (MRF) modelling technique. This model is developed by formulating the maximum posteriori decision rule as the minimization of suitable energy functions. For select optimum distribution which adapts the data more efficiently we used Mellin transform which is a natural analytical tool to study the distribution of products and quotients of independent random variables. Our proposed classification method is applied to a full polarimetric L-band dataset acquired from an agricultural region in Winnipeg, Canada. We evaluate the classification performance based on kappa and overall accuracies of the proposed approach and compared with other well-known classic methods.

  6. An Efficient Full-Wave Electromagnetic Analysis for Capacitive Body-Coupled Communication

    Directory of Open Access Journals (Sweden)

    Muhammad Irfan Kazim

    2015-01-01

    Full Text Available Measured propagation loss for capacitive body-coupled communication (BCC channel (1 MHz to 60 MHz is limitedly available in the literature for distances longer than 50 cm. This is either because of experimental complexity to isolate the earth-ground or design complexity in realizing a reliable communication link to assess the performance limitations of capacitive BCC channel. Therefore, an alternate efficient full-wave electromagnetic (EM simulation approach is presented to realistically analyze capacitive BCC, that is, the interaction of capacitive coupler, the human body, and the environment all together. The presented simulation approach is first evaluated for numerical/human body variation uncertainties and then validated with measurement results from literature, followed by the analysis of capacitive BCC channel for twenty different scenarios. The simulation results show that the vertical coupler configuration is less susceptible to physiological variations of underlying tissues compared to the horizontal coupler configuration. The propagation loss is less for arm positions when they are not touching the torso region irrespective of the communication distance. The propagation loss has also been explained for complex scenarios formed by the ground-plane and the material structures (metals or dielectrics with the human body. The estimated propagation loss has been used to investigate the link-budget requirement for designing capacitive BCC system in CMOS sub-micron technologies.

  7. Full-Range Public Health Leadership, Part 2: Qualitative Analysis and Synthesis

    Directory of Open Access Journals (Sweden)

    Erik L. Carlton

    2015-07-01

    Full Text Available Public health leadership is an important topic in the era of U. S. health reform, population health innovation, and health system transformation. This study utilized the full-range leadership model in order to examine public health leadership. We sought to understand local public health leadership from the perspective of local health department leaders and those who work with and for them. Public health leadership was explored through interviews and focus groups with directors (n=4 and staff (n=33 from local health departments. Qualitative analytic methods included reflexive journals, code-recode procedures, and member checking, with analysis facilitated by Atlas.ti v.6.0. Qualitative results supported and expanded upon previously reported quantitative findings. Leading by example and providing individual consideration to followers were found to be more important than other leader factors such as intellectual stimulation, inspirational motivation, or idealized attributes of leaders. Having a clear and competent vision of public health, being able to work collaboratively with other community agencies, and addressing the current challenges to public health with creativity and innovation were also important findings. Idealized leadership behaviors and individual consideration should be the focus of student and professional development. Models that incorporate contextual considerations, such as the situational leadership model, should be utilized and instruction in basic interpersonal skills may prove useful. The development of a detailed leadership assessment and development process for public health practitioners is indicated.

  8. Performance Analysis of User Pairing Algorithm in Full-Duplex Cellular Networks

    Directory of Open Access Journals (Sweden)

    Wonjong Noh

    2017-01-01

    Full Text Available In a full duplexing (FD wireless cellular network, a base station operates in FD mode, while the downlink (DL and uplink (UL users operate in half duplexing (HD mode. Thus, the downlink and uplink transmissions occur simultaneously so that interuser interference from a UL to a DL user occurs. In an FD network, the main challenge to minimize the interuser interference is user pairing, which determines a pair of DL and UL users who use the same radio resource simultaneously. We formulate a nonconvex optimization problem for user pairing to maximize the cell throughput. Then, we propose a heuristic user pairing algorithm with low complexity. This algorithm is designed such that the DL user having a better signal quality has higher priority to choose its paired UL user for throughput maximization. Thereafter, we conduct theoretical performance analysis of the FD cellular system based on stochastic geometry and analyze the impact of the user paring algorithm on the performance of the FD cellular system. Results show that the FD system that uses the proposed user pairing algorithm effectively reduces the interuser interference and approaches optimal performance. It also considerably outperforms the FD system using a random user pairing and almost doubles the conventional HD system in terms of cell throughput.

  9. Analysis of Photovoltaic Fed Partially Isolated Three-Port Full Bridge Converter with the Centralised Controller

    Directory of Open Access Journals (Sweden)

    Venmathi M

    2014-07-01

    Full Text Available In this paper analysis of an efficient topology of the three-port full bridge dc-dc converter is presented. This topology is promising with the view points of centralised control, compact design as it is capable of interfacing many numbers of ports with less number of switches, low cost, simple and fast power flow management with reduced conversion process. In a stand-alone system this topology is used to interface renewable energy sources and the load along with the energy storage device. Thus the proposed topology interfaces three ports: as one source port, one bidirectional storage port and an isolated output port. The key feature of this converter is that it performs buck-boost operation on the input port side to obtain power balance in the system with the centralised controller. The centralised controller was implemented by using proportional Integral (PI controller. Such that it is used to track maximum power from the Photovoltaic (PV system and to regulate output voltage by controlling the charging and the discharging characteristics of the battery. Zero voltage switching (ZVS is also achieved in all the switches by using the energy stored in the leakage inductance of the transformer, output filter inductance and capacitance.

  10. A Big Data Analytics Pipeline for the Analysis of TESS Full Frame Images

    Science.gov (United States)

    Wampler-Doty, Matthew; Pierce Doty, John

    2015-12-01

    We present a novel method for producing a catalogue of extra-solar planets and transients using the full frame image data from TESS. Our method involves (1) creating a fast Monte Carlo simulation of the TESS science instruments, (2) using the simulation to create a labeled dataset consisting of exoplanets with various orbital durations as well as transients (such as tidal disruption events), (3) using supervised machine learning to find optimal matched filters, Support Vector Machines (SVMs) and statistical classifiers (i.e. naïve Bayes and Markov Random Fields) to detect astronomical objects of interest and (4) “Big Data” analysis to produce a catalogue based on the TESS data. We will apply the resulting methods to all stars in the full frame images. We hope that by providing libraries that conform to industry standards of Free Open Source Software we may invite researchers from the astronomical community as well as the wider data-analytics community to contribute to our effort.

  11. Urinary tract infection in full-term newborn infants: risk factor analysis

    Directory of Open Access Journals (Sweden)

    Falcão Mário Cícero

    2000-01-01

    Full Text Available OBJECTIVE: To analyze the correlation of risk factors to the occurrence of urinary tract infection in full-term newborn infants. PATIENTS AND METHODS: Retrospective study (1997 including full-term infants having a positive urine culture by bag specimen. Urine collection was based on: fever, weight loss > 10% of birth weight, nonspecific symptoms (feeding intolerance, failure to thrive, hypoactivity, debilitate suction, irritability, or renal and urinary tract malformations. In these cases, another urine culture by suprapubic bladder aspiration was collected to confirm the diagnosis. To compare and validate the risk factors in each group, the selected cases were divided into two groups: Group I - positive urine culture by bag specimen collection and negative urine culture by suprapubic aspiration, and Group II - positive urine culture by bag specimen collection and positive urine culture by suprapubic aspiration . RESULTS: Sixty one infants were studied, Group I, n = 42 (68.9% and Group II, n = 19 (31.1%. The selected risk factors (associated infectious diseases, use of broad-spectrum antibiotics, renal and urinary tract malformations, mechanical ventilation, parenteral nutrition and intravascular catheter were more frequent in Group II (p<0.05. Through relative risk analysis, risk factors were, in decreasing importance: parenteral nutrition, intravascular catheter, associated infectious diseases, use of broad-spectrum antibiotics, mechanical ventilation, and renal and urinary tract malformations. CONCLUSION: The results showed that parenteral nutrition, intravascular catheter, and associated infectious diseases contributed to increase the frequency of neonatal urinary tract infection, and in the presence of more than one risk factor, the occurrence of urinary tract infection rose up to 11 times.

  12. Seismic analysis of the large 70-meter antenna, part 1: Earthquake response spectra versus full transient analysis

    Science.gov (United States)

    Kiedron, K.; Chian, C. T.

    1985-01-01

    As a check on structure safety aspects, two approaches in seismic analysis for the large 70-m antennas are presented. The first approach, commonly used by civil engineers, utilizes known recommended design response spectra. The second approach, which is the full transient analysis, is versatile and applicable not only to earthquake loading but also to other dynamic forcing functions. The results obtained at the fundamental structural frequency show that the two approaches are in good agreement with each other and both approaches show a safe design. The results also confirm past 64-m antenna seismic studies done by the Caltech Seismology Staff.

  13. Towards the Procedure Automation of Full Stochastic Spectral Based Fatigue Analysis

    Directory of Open Access Journals (Sweden)

    Khurram Shehzad

    2013-05-01

    Full Text Available Fatigue is one of the most significant failure modes for marine structures such as ships and offshore platforms. Among numerous methods for fatigue life estimation, spectral method is considered as the most reliable one due to its ability to cater different sea states as well as their probabilities of occurrence. However, spectral based simulation procedure itself is quite complex and numerically intensive owing to various critical technical details. Present research study is focused on the application and automation of spectral based fatigue analysis procedure for ship structure using ANSYS software with 3D liner sea keeping code AQWA. Ansys Parametric Design Language (APDL macros are created and subsequently implemented to automate the workflow of simulation process by reducing the time spent on non-value added repetitive activity. A MATLAB program based on direct calculation procedure of spectral fatigue is developed to calculate total fatigue damage. The automation procedure is employed to predict the fatigue life of a ship structural detail using wave scatter data of North Atlantic and Worldwide trade. The current work will provide a system for efficient implementation of stochastic spectral fatigue analysis procedure for ship structures.

  14. A selection model for accounting for publication bias in a full network meta-analysis.

    Science.gov (United States)

    Mavridis, Dimitris; Welton, Nicky J; Sutton, Alex; Salanti, Georgia

    2014-12-30

    Copas and Shi suggested a selection model to explore the potential impact of publication bias via sensitivity analysis based on assumptions for the probability of publication of trials conditional on the precision of their results. Chootrakool et al. extended this model to three-arm trials but did not fully account for the implications of the consistency assumption, and their model is difficult to generalize for complex network structures with more than three treatments. Fitting these selection models within a frequentist setting requires maximization of a complex likelihood function, and identification problems are common. We have previously presented a Bayesian implementation of the selection model when multiple treatments are compared with a common reference treatment. We now present a general model suitable for complex, full network meta-analysis that accounts for consistency when adjusting results for publication bias. We developed a design-by-treatment selection model to describe the mechanism by which studies with different designs (sets of treatments compared in a trial) and precision may be selected for publication. We fit the model in a Bayesian setting because it avoids the numerical problems encountered in the frequentist setting, it is generalizable with respect to the number of treatments and study arms, and it provides a flexible framework for sensitivity analysis using external knowledge. Our model accounts for the additional uncertainty arising from publication bias more successfully compared to the standard Copas model or its previous extensions. We illustrate the methodology using a published triangular network for the failure of vascular graft or arterial patency.

  15. SRM Internal Flow Tests and Computational Fluid Dynamic Analysis. Volume 2; CFD RSRM Full-Scale Analyses

    Science.gov (United States)

    2001-01-01

    This document presents the full-scale analyses of the CFD RSRM. The RSRM model was developed with a 20 second burn time. The following are presented as part of the full-scale analyses: (1) RSRM embedded inclusion analysis; (2) RSRM igniter nozzle design analysis; (3) Nozzle Joint 4 erosion anomaly; (4) RSRM full motor port slag accumulation analysis; (5) RSRM motor analysis of two-phase flow in the aft segment/submerged nozzle region; (6) Completion of 3-D Analysis of the hot air nozzle manifold; (7) Bates Motor distributed combustion test case; and (8) Three Dimensional Polysulfide Bump Analysis.

  16. Artrópodos con interés vectorial en la salud pública en España

    Directory of Open Access Journals (Sweden)

    Rubén Bueno Marí

    2009-01-01

    Full Text Available Quince de las treinta y una Enfermedades de Declaración Obligatoria en España, exceptuando las de tipo congénito o neonatal, pueden ser transmitidas por diversas especies de artrópodos que están presentes en nuestro país. Decenas de bacterias, hongos, virus y protozoos tienen en diversos órdenes de artrópodos a sus agentes transmisores ideales. Este hecho hace que sea necesario conocer su biología para poder adoptar medidas de control que sean eficaces y nos permitan disminuir la incidencia de estas enfermedades. Sin embargo, los estudios epidemiológicos, lejos de quedar únicamente restringidos a las enfermedades que presentan ciclos activos de transmisión en nuestro país, deben adquirir una visión más global, en la que se incluyan también enfermedades alóctonas pero con una elevada probabilidad de que se transmitan a nuestro territorio en el contexto de globalización en el que nos hallamos. De este modo se conseguirá conocer qué factores impiden su presencia actual y dotar a la Red Nacional de Vigilancia Epidemiológica de una capacidad predictiva que permita pronosticar la posible llegada de la enfermedad, fortaleciendo a fin de cuentas la Salud Pública española. El objetivo del presente trabajo es llevar a cabo una revisión de la artropodofauna de interés vectorial en España. Se discute la situación actual en nuestro país de algunas de las enfermedades más importantes con transmisión vectorial, así como los factores que pueden determinar su aparición, resurgencia y/o recrudecimiento. El estudio de estos agentes en nuestra Salud Pública resulta imprescindible como un elemento más articulado en la compleja red que toda enfermedad de tipo vectorial conlleva.

  17. Molecular characterization and phylogenetic analysis of full-genome HBV subgenotype D3 sequences from Serbia.

    Science.gov (United States)

    Stanojević, Boban; Osiowy, Carla; Schaefer, Stephan; Bojović, Ksenija; Blagojević, Jelena; Nešić, Milica; Yamashita, Shunichi; Stamenković, Gorana

    2011-08-01

    Hepatitis B virus (HBV) is classified into 8 genotypes with distinct geographical distribution. Genotype D (HBV/D) has the widest distribution area and is comprised of 7 subgenotypes. Subgenotypes D1, D2 and D3 appear worldwide, while D4-D7 have a more restricted distribution. Within the Mediterranean area, HBV/D and subgenotype D3 are the most prevalent. The purpose of this study was to characterize the full genome of Serbian HBV/D3 isolates by comparison and phylogenetic analysis with HBV/D3 sequences (66 samples) found in GeneBank/DDBJ databases from different parts of the world. Isolates were obtained from three patients diagnosed with chronic hepatitis B (HBsAg+). All three isolates have two very rare nucleotide substitutions, A929T and T150A, which indicate the same ancestor. Phylogenetic analysis of HBV/D3 genome sequences throughout the world follows an ethno-geographical origin of isolates with rare exceptions, which could be explained by human travelling and migration. The geographically close but ethnically different Serbian and Italian isolates clustered in the same subnode, and on a common branch with strains from Northern Canada. To test the apparently close HBV phylogenetic relationship between completely separated patients from Serbia and Northern Canada we analyzed in depth a 440 bp region of the HBsAg from Canadian (n=73) and Serbian (n=70) isolates. The constructed parsimony tree revealed that strains from Serbia and Northern Canada fell along the same branch which indicates independent evolution within regions of each country. Considering that HBsAg sequence has limited variability for phylogenetic analyses, our hypothesis needs further confirmation with more HBV complete genome sequences.

  18. Estimation of surface curvature from full-field shape data using principal component analysis

    Science.gov (United States)

    Sharma, Sameer; Vinuchakravarthy, S.; Subramanian, S. J.

    2017-01-01

    Three-dimensional digital image correlation (3D-DIC) is a popular image-based experimental technique for estimating surface shape, displacements and strains of deforming objects. In this technique, a calibrated stereo rig is used to obtain and stereo-match pairs of images of the object of interest from which the shapes of the imaged surface are then computed using the calibration parameters of the rig. Displacements are obtained by performing an additional temporal correlation of the shapes obtained at various stages of deformation and strains by smoothing and numerically differentiating the displacement data. Since strains are of primary importance in solid mechanics, significant efforts have been put into computation of strains from the measured displacement fields; however, much less attention has been paid to date to computation of curvature from the measured 3D surfaces. In this work, we address this gap by proposing a new method of computing curvature from full-field shape measurements using principal component analysis (PCA) along the lines of a similar work recently proposed to measure strains (Grama and Subramanian 2014 Exp. Mech. 54 913-33). PCA is a multivariate analysis tool that is widely used to reveal relationships between a large number of variables, reduce dimensionality and achieve significant denoising. This technique is applied here to identify dominant principal components in the shape fields measured by 3D-DIC and these principal components are then differentiated systematically to obtain the first and second fundamental forms used in the curvature calculation. The proposed method is first verified using synthetically generated noisy surfaces and then validated experimentally on some real world objects with known ground-truth curvatures.

  19. Full-Range Public Health Leadership, Part 2: Qualitative Analysis and Synthesis

    Science.gov (United States)

    Carlton, Erik L.; Holsinger, James W.; Riddell, Martha C.; Bush, Heather

    2015-01-01

    Public health leadership is an important topic in the era of U.S. health reform, population health innovation, and health system transformation. This study utilized the full-range leadership model in order to examine the public health leadership. We sought to understand local public health leadership from the perspective of local health department leaders and those who work with and for them. Public health leadership was explored through interviews and focus groups with directors (n = 4) and staff (n = 33) from local health departments. Qualitative analytic methods included reflexive journals, code-recode procedures, and member checking, with analysis facilitated by Atlas.ti v.6.0. Qualitative results supported and expanded upon previously reported quantitative findings. Leading by example and providing individual consideration to followers were found to be more important than other leader factors, such as intellectual stimulation, inspirational motivation, or idealized attributes of leaders. Having a clear and competent vision of public health, being able to work collaboratively with other community agencies, and addressing the current challenges to public health with creativity and innovation were also important findings. Idealized leadership behaviors and individual consideration should be the focus of student and professional development. Models that incorporate contextual considerations, such as the situational leadership model, could be utilized to ensure that optimal individual consideration is given to followers. PMID:26217654

  20. The Extended GMRT Radio Halo Survey II: Further results and analysis of the full sample

    CERN Document Server

    Kale, R; Giacintucci, S; Dallacasa, D; Cassano, R; Brunetti, G; Cuciti, V; Macario, G; Athreya, R

    2015-01-01

    The intra-cluster medium contains cosmic rays and magnetic fields that are manifested through the large scale synchrotron sources, termed as radio halos, relics and mini-halos. The Extended Giant Metrewave Radio Telescope (GMRT) Radio Halo Survey (EGRHS) is an extension of the GMRT Radio Halo Survey (GRHS) designed to search for radio halos using GMRT 610/235 MHz observations. The GRHS+EGRHS consists of 64 clusters in the redshift range 0.2 -- 0.4 that have an X-ray luminosity larger than 5x10^44 erg/s in the 0.1 -- 2.4 keV band and with declinations > -31 deg in the REFLEX and eBCS X-ray cluster catalogues. In this second paper in the series, GMRT 610/235 MHz data on the last batch of 11 galaxy clusters and the statistical analysis of the full sample are presented. A new mini-halo in RXJ2129.6+0005 and candidate diffuse sources in Z5247, A2552 and Z1953 are discovered. A unique feature of this survey are the upper limits on the detections of 1 Mpc sized radio halos; 4 new are presented here making a total of...

  1. Regularized discriminate analysis for breast mass detection on full field digital mammograms

    Science.gov (United States)

    Wei, Jun; Sahiner, Berkman; Zhang, Yiheng; Chan, Heang-Ping; Hadjiiski, Lubomir M.; Zhou, Chuan; Ge, Jun; Wu, Yi-Ta

    2006-03-01

    In computer-aided detection (CAD) applications, an important step is to design a classifier for the differentiation of the abnormal from the normal structures. We have previously developed a stepwise linear discriminant analysis (LDA) method with simplex optimization for this purpose. In this study, our goal was to investigate the performance of a regularized discriminant analysis (RDA) classifier in combination with a feature selection method for classification of the masses and normal tissues detected on full field digital mammograms (FFDM). The feature selection scheme combined a forward stepwise feature selection process and a backward stepwise feature elimination process to obtain the best feature subset. An RDA classifier and an LDA classifier in combination with this new feature selection method were compared to an LDA classifier with stepwise feature selection. A data set of 130 patients containing 260 mammograms with 130 biopsy-proven masses was used. All cases had two mammographic views. The true locations of the masses were identified by experienced radiologists. To evaluate the performance of the classifiers, we randomly divided the data set into two independent sets of approximately equal size for training and testing. The training and testing were performed using the 2-fold cross validation method. The detection performance of the CAD system was assessed by free response receiver operating characteristic (FROC) analysis. The average test FROC curve was obtained by averaging the FP rates at the same sensitivity along the two corresponding test FROC curves from the 2-fold cross validation. At the case-based sensitivities of 90%, 80% and 70% on the test set, our RDA classifier with the new feature selection scheme achieved an FP rate of 1.8, 1.1, and 0.6 FPs/image, respectively, compared to 2.1, 1.4, and 0.8 FPs/image with stepwise LDA with simplex optimization. Our results indicate that RDA in combination with the sequential forward inclusion

  2. A note on vectorial AdS5/CFT4 duality for spin- j boundary theory

    Science.gov (United States)

    Bae, Jin-Beom; Joung, Euihun; Lal, Shailesh

    2016-12-01

    The vectorial holographic correspondences between higher-spin theories in AdS5 and free vector models on the boundary are extended to the cases where the latter is described by free massless spin- j field. The dual higher-spin theory in the bulk does not include gravity and can only be defined on rigid AdS5 background with S 4 boundary. We discuss various properties of these rather special higher-spin theories and calculate their one-loop free energies. We show that the result is proportional to the same quantity for spin- j doubleton treated as if it is a AdS5 field. Finally, we consider even more special case where the boundary theory itself is given by an infinite tower of massless higher-spin fields.

  3. Vectorial platform for manipulating the polarization mode train realized with Jones vectors in Mathematica

    Science.gov (United States)

    Kim, Tae Wan; Yun, Hee-Joong

    2016-09-01

    A fundamental concept in physics of polarization propagation of electromagnetic waves is newly understood as a cardinal keyword in quantum cryptography transport technology and cosmology. Recently, interactive visualization of the propagation mechanism of polarized electromagnetism in a medium with helicity has received attention from scientists in the age of information and communication. This study presents a new dynamic polarization platform that manipulates the polarization mode train of a transverse electromagnetic wave by using calculations with Jones vectors in the symbolic program Mathematica. The train of polarization modes is converted continuously through a desirable lineup of optical elements in the platform. The platform simulates a propagation process that satisfies Maxwell's two vector equations precisely with helicity in the vectorial nature of the electromagnetic wave.

  4. Scanning metallic nanosphere microscopy for vectorial profiling of optical focal spots.

    Science.gov (United States)

    Yi, Hui; Long, Jing; Li, Hongquan; He, Xiaolong; Yang, Tian

    2015-04-06

    Recent years have witnessed fast progress in the development of spatially variant states of polarization under high numerical aperture focusing, and intensive exploration of their applications. We report a vectorial, broadband, high contrast and subwavelength resolution method for focal spot profiling. In this experiment, a 100 nm diameter gold nanosphere on a silica aerogel substrate is raster scanned across the focal spots, and the orthogonal polarization components can be obtained simultaneously by measuring the scattering far field in a confocal manner. The metallic-nanosphere-on-aerogel structure ensures negligible distortion to the focal spots, low crosstalk between orthogonal polarization components (1/39 in experiment), and a low level background noise (1/80 of peak intensity in experiment), while high contrast imaging is not limited by the resonance bandwidth.

  5. Three-dimensional polarization marked multiple-QR code encryption by optimizing a single vectorial beam

    Science.gov (United States)

    Lin, Chao; Shen, Xueju; Hua, Binbin; Wang, Zhisong

    2015-10-01

    We demonstrate the feasibility of three dimensional (3D) polarization multiplexing by optimizing a single vectorial beam using a multiple-signal window multiple-plane (MSW-MP) phase retrieval algorithm. Original messages represented with multiple quick response (QR) codes are first partitioned into a series of subblocks. Then, each subblock is marked with a specific polarization state and randomly distributed in 3D space with both longitudinal and transversal adjustable freedoms. A generalized 3D polarization mapping protocol is established to generate a 3D polarization key. Finally, multiple-QR code is encrypted into one phase only mask and one polarization only mask based on the modified Gerchberg-Saxton (GS) algorithm. We take the polarization mask as the cyphertext and the phase only mask as additional dimension of key. Only when both the phase key and 3D polarization key are correct, original messages can be recovered. We verify our proposal with both simulation and experiment evidences.

  6. Seismic response of a full-scale wind turbine tower using experimental and numerical modal analysis

    Science.gov (United States)

    Kandil, Kamel Sayed Ahmad; Saudi, Ghada N.; Eltaly, Boshra Aboul-Anen; El-khier, Mostafa Mahmoud Abo

    2016-09-01

    Wind turbine technology has developed tremendously over the past years. In Egypt, the Zafarana wind farm is currently generating at a capacity of 517 MW, making it one of the largest onshore wind farms in the world. It is located in an active seismic zone along the west side of the Gulf of Suez. Accordingly, seismic risk assessment is demanded for studying the structural integrity of wind towers under expected seismic hazard events. In the context of ongoing joint Egypt-US research project "Seismic Risk Assessment of Wind Turbine Towers in Zafarana wind Farm Egypt" (Project ID: 4588), this paper describes the dynamic performance investigation of an existing Nordex N43 wind turbine tower. Both experimental and numerical work are illustrated explaining the methodology adopted to investigate the dynamic behavior of the tower under seismic load. Field dynamic testing of the full-scale tower was performed using ambient vibration techniques (AVT). Both frequency domain and time domain methods were utilized to identify the actual dynamic properties of the tower as built in the site. Mainly, the natural frequencies, their corresponding mode shapes and damping ratios of the tower were successfully identified using AVT. A vibration-based finite element model (FEM) was constructed using ANSYS V.12 software. The numerical and experimental results of modal analysis were both compared for matching purpose. Using different simulation considerations, the initial FEM was updated to finally match the experimental results with good agreement. Using the final updated FEM, the response of the tower under the AQABA earthquake excitation was investigated. Time history analysis was conducted to define the seismic response of the tower in terms of the structural stresses and displacements. This work is considered as one of the pioneer structural studies of the wind turbine towers in Egypt. Identification of the actual dynamic properties of the existing tower was successfully performed

  7. Seismic response of a full-scale wind turbine tower using experimental and numerical modal analysis

    Science.gov (United States)

    Kandil, Kamel Sayed Ahmad; Saudi, Ghada N.; Eltaly, Boshra Aboul-Anen; El-khier, Mostafa Mahmoud Abo

    2016-12-01

    Wind turbine technology has developed tremendously over the past years. In Egypt, the Zafarana wind farm is currently generating at a capacity of 517 MW, making it one of the largest onshore wind farms in the world. It is located in an active seismic zone along the west side of the Gulf of Suez. Accordingly, seismic risk assessment is demanded for studying the structural integrity of wind towers under expected seismic hazard events. In the context of ongoing joint Egypt-US research project "Seismic Risk Assessment of Wind Turbine Towers in Zafarana wind Farm Egypt" (Project ID: 4588), this paper describes the dynamic performance investigation of an existing Nordex N43 wind turbine tower. Both experimental and numerical work are illustrated explaining the methodology adopted to investigate the dynamic behavior of the tower under seismic load. Field dynamic testing of the full-scale tower was performed using ambient vibration techniques (AVT). Both frequency domain and time domain methods were utilized to identify the actual dynamic properties of the tower as built in the site. Mainly, the natural frequencies, their corresponding mode shapes and damping ratios of the tower were successfully identified using AVT. A vibration-based finite element model (FEM) was constructed using ANSYS V.12 software. The numerical and experimental results of modal analysis were both compared for matching purpose. Using different simulation considerations, the initial FEM was updated to finally match the experimental results with good agreement. Using the final updated FEM, the response of the tower under the AQABA earthquake excitation was investigated. Time history analysis was conducted to define the seismic response of the tower in terms of the structural stresses and displacements. This work is considered as one of the pioneer structural studies of the wind turbine towers in Egypt. Identification of the actual dynamic properties of the existing tower was successfully performed

  8. Full quantum mechanical analysis of atomic three-grating Mach–Zehnder interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Sanz, A.S., E-mail: asanz@iff.csic.es [Instituto de Física Fundamental (IFF-CSIC), Serrano 123, 28006 Madrid (Spain); Davidović, M. [Faculty of Civil Engineering, University of Belgrade, Bulevar Kralja Aleksandra 73, 11000 Belgrade (Serbia); Božić, M. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia)

    2015-02-15

    Atomic three-grating Mach–Zehnder interferometry constitutes an important tool to probe fundamental aspects of the quantum theory. There is, however, a remarkable gap in the literature between the oversimplified models and robust numerical simulations considered to describe the corresponding experiments. Consequently, the former usually lead to paradoxical scenarios, such as the wave–particle dual behavior of atoms, while the latter make difficult the data analysis in simple terms. Here these issues are tackled by means of a simple grating working model consisting of evenly-spaced Gaussian slits. As is shown, this model suffices to explore and explain such experiments both analytically and numerically, giving a good account of the full atomic journey inside the interferometer, and hence contributing to make less mystic the physics involved. More specifically, it provides a clear and unambiguous picture of the wavefront splitting that takes place inside the interferometer, illustrating how the momentum along each emerging diffraction order is well defined even though the wave function itself still displays a rather complex shape. To this end, the local transverse momentum is also introduced in this context as a reliable analytical tool. The splitting, apart from being a key issue to understand atomic Mach–Zehnder interferometry, also demonstrates at a fundamental level how wave and particle aspects are always present in the experiment, without incurring in any contradiction or interpretive paradox. On the other hand, at a practical level, the generality and versatility of the model and methodology presented, makes them suitable to attack analogous problems in a simple manner after a convenient tuning. - Highlights: • A simple model is proposed to analyze experiments based on atomic Mach–Zehnder interferometry. • The model can be easily handled both analytically and computationally. • A theoretical analysis based on the combination of the position and

  9. Community analysis of a full-scale anaerobic bioreactor treating paper mill wastewater.

    Science.gov (United States)

    Roest, Kees; Heilig, Hans G H J; Smidt, Hauke; de Vos, Willem M; Stams, Alfons J M; Akkermans, Antoon D L

    2005-03-01

    To get insight into the microbial community of an Upflow Anaerobic Sludge Blanket reactor treating paper mill wastewater, conventional microbiological methods were combined with 16S rRNA gene analyses. Particular attention was paid to microorganisms able to degrade propionate or butyrate in the presence or absence of sulphate. Serial enrichment dilutions allowed estimating the number of microorganisms per ml sludge that could use butyrate with or without sulphate (10(5)), propionate without sulphate (10(6)), or propionate and sulphate (10(8)). Quantitative RNA dot-blot hybridisation indicated that Archaea were two-times more abundant in the microbial community of anaerobic sludge than Bacteria. The microbial community composition was further characterised by 16S rRNA-gene-targeted Denaturing Gradient Gel Electrophoresis (DGGE) fingerprinting, and via cloning and sequencing of dominant amplicons from the bacterial and archaeal patterns. Most of the nearly full length (approximately 1.45 kb) bacterial 16S rRNA gene sequences showed less than 97% similarity to sequences present in public databases, in contrast to the archaeal clones (approximately. 1.3 kb) that were highly similar to known sequences. While Methanosaeta was found as the most abundant genus, also Crenarchaeote-relatives were identified. The microbial community was relatively stable over a period of 3 years (samples taken in July 1999, May 2001, March 2002 and June 2002) as indicated by the high similarity index calculated from DGGE profiles (81.9+/-2.7% for Bacteria and 75.1+/-3.1% for Archaea). 16S rRNA gene sequence analysis indicated the presence of unknown and yet uncultured microorganisms, but also showed that known sulphate-reducing bacteria and syntrophic fatty acid-oxidising microorganisms dominated the enrichments.

  10. Stoichiometry of vectorial H+ movements coupled to electron transport and to ATP synthesis in mitochondria.

    Science.gov (United States)

    Alexandre, A; Reynafarje, B; Lehninger, A L

    1978-11-01

    In order to verify more directly our earlier measurements showing that, on the average, close to four vectorial H(+) are rejected per pair of electrons passing each of the three energy-conserving sites of the mitochondrial electron transport chain, direct tests of the H(+)/2e(-) ratio for sites 2 and 3 were carried out in the presence of permeant charge-compensating cations. Site 2 was examined by utilizing succinate as electron donor and ferricyanide as electron acceptor from mitochondrial cytochrome c; the directly measured H(+)/2e(-) ratio was close to 4. Energy-conserving site 3 was isolated for study with ferrocyanide or ascorbate plus tetramethylphenylenediamine as electron donors to cytochrome c and with oxygen as electron acceptor. The directly measured H(+)/2e(-) ratio for site 3 was close to 4. The H(+)/ATP ratio (number of vectorial H(+) ejected per ATP hydrolyzed) was determined with a new method in which the steady-state rates of both H(+) ejection and ATP hydrolysis were measured in the presence of K(+) + valinomycin. The H(+)/ATP ratio was found to approach 3.0. A proton cycle for oxidative phosphorylation is proposed, in which four electrochemical H(+) equivalents are ejected per pair of electrons passing each energy-conserving site; three of the H(+) equivalents pass inward to derive ATP synthesis from ADP and phosphate and the fourth H(+) is used to bring about the energy-requiring electrogenic expulsion of ATP(4-) in exchange for extramitochondrial ADP(3-), via the H(+)/H(2)PO(4) (-) symporter.

  11. Design and Analysis of a New Carbon Nanotube Full Adder Cell

    Directory of Open Access Journals (Sweden)

    M. H. Ghadiry

    2011-01-01

    Full Text Available A novel full adder circuit is presented. The main aim is to reduce power delay product (PDP in the presented full adder cell. A new method is used in order to design a full-swing full adder cell with low number of transistors. The proposed full adder is implemented in MOSFET-like carbon nanotube technology and the layout is provided based on standard 32 nm technology from MOSIS. The simulation results using HSPICE show that there are substantial improvements in both power and performance of the proposed circuit compared to the latest designs. In addition, the proposed circuit has been implemented in conventional 32 nm process to compare the benefits of using MOSFET-like carbon nanotubes in arithmetic circuits over conventional CMOS technology. The proposed circuit can be applied in very high performance and ultra-low-power applications.

  12. Analysis of 4,664 high-quality sequence-finished poplar full-length

    Energy Technology Data Exchange (ETDEWEB)

    Ralph, S. [University of British Columbia, Vancouver; Gunter, Lee E [ORNL; Tuskan, Gerald A [ORNL; Douglas, Carl [University of British Columbia, Vancouver; Holt, Robert A. [Genome Sciences Centre, Vancouver, BC, Canada; Jones, Steven [Genome Sciences Centre, Vancouver, BC, Canada; Marra, Marco [Genome Sciences Centre, Vancouver, BC, Canada; Bohlmann, J. [University of British Columbia, Vancouver

    2008-01-01

    The genus Populus includes poplars, aspens and cottonwoods, which will be collectively referred to as poplars hereafter unless otherwise specified. Poplars are the dominant tree species in many forest ecosystems in the Northern Hemisphere and are of substantial economic value in plantation forestry. Poplar has been established as a model system for genomics studies of growth, development, and adaptation of woody perennial plants including secondary xylem formation, dormancy, adaptation to local environments, and biotic interactions. As part of the poplar genome sequencing project and the development of genomic resources for poplar, we have generated a full-length (FL)-cDNA collection using the biotinylated CAP trapper method. We constructed four FLcDNA libraries using RNA from xylem, phloem and cambium, and green shoot tips and leaves from the P. trichocarpa Nisqually-1 genotype, as well as insect-attacked leaves of the P. trichocarpa x P. deltoides hybrid. Following careful selection of candidate cDNA clones, we used a combined strategy of paired end reads and primer walking to generate a set of 4,664 high-accuracy, sequence-verified FLcDNAs, which clustered into 3,990 putative unique genes. Mapping FLcDNAs to the poplar genome sequence combined with BLAST comparisons to previously predicted protein coding sequences in the poplar genome identified 39 FLcDNAs that likely localize to gaps in the current genome sequence assembly. Another 173 FLcDNAs mapped to the genome sequence but were not included among the previously predicted genes in the poplar genome. Comparative sequence analysis against Arabidopsis thaliana and other species in the non-redundant database of GenBank revealed that 11.5% of the poplar FLcDNAs display no significant sequence similarity to other plant proteins. By mapping the poplar FLcDNAs against transcriptome data previously obtained with a 15.5 K cDNA microarray, we identified 153 FLcDNA clones for genes that were differentially expressed in

  13. Full-Wave Techniques for the Analysis of Electrodynamics and Coherent Quantum Transport in Graphene Nanodevices.

    Directory of Open Access Journals (Sweden)

    Luca Pierantoni

    2012-11-01

    Full Text Available We report on full-wave techniques in the frequency (energy-domain and the time-domain, aimed at the investigation of the combined electromagnetic-coherent transport problem in carbon based nanostructured materials and devices viz. graphene nanoribbons. The frequency-domain approach is introduced in order to describe a Poisson-Schrödinger / Dirac system in a quasi static framework. Thetime-domain approach deals with the full-wave solution of the combined Maxwell-Schrödinger / Dirac system of equations. From the above theoretical platforms, home-made solvers are provided, aimed atdealing with challenging problems in realistic devices / systems environments, typical of the area of radio-frequency nanoelectronics.

  14. Analysis and Construction of Full-Diversity Joint Network-LDPC Codes for Cooperative Communications

    Directory of Open Access Journals (Sweden)

    Capirone Daniele

    2010-01-01

    Full Text Available Transmit diversity is necessary in harsh environments to reduce the required transmit power for achieving a given error performance at a certain transmission rate. In networks, cooperative communication is a well-known technique to yield transmit diversity and network coding can increase the spectral efficiency. These two techniques can be combined to achieve a double diversity order for a maximum coding rate on the Multiple-Access Relay Channel (MARC, where two sources share a common relay in their transmission to the destination. However, codes have to be carefully designed to obtain the intrinsic diversity offered by the MARC. This paper presents the principles to design a family of full-diversity LDPC codes with maximum rate. Simulation of the word error rate performance of the new proposed family of LDPC codes for the MARC confirms the full diversity.

  15. Full tensor gravity gradiometry data inversion: Performance analysis of parallel computing algorithms

    Science.gov (United States)

    Hou, Zhen-Long; Wei, Xiao-Hui; Huang, Da-Nian; Sun, Xu

    2015-09-01

    We apply reweighted inversion focusing to full tensor gravity gradiometry data using message-passing interface (MPI) and compute unified device architecture (CUDA) parallel computing algorithms, and then combine MPI with CUDA to formulate a hybrid algorithm. Parallel computing performance metrics are introduced to analyze and compare the performance of the algorithms. We summarize the rules for the performance evaluation of parallel algorithms. We use model and real data from the Vinton salt dome to test the algorithms. We find good match between model and real density data, and verify the high efficiency and feasibility of parallel computing algorithms in the inversion of full tensor gravity gradiometry data.

  16. Mathematical analysis of plasmonic resonances for nanoparticles: The full Maxwell equations

    Science.gov (United States)

    Ammari, Habib; Ruiz, Matias; Yu, Sanghyeon; Zhang, Hai

    2016-09-01

    In this paper we use the full Maxwell equations for light propagation in order to analyze plasmonic resonances for nanoparticles. We mathematically define the notion of plasmonic resonance and analyze its shift and broadening with respect to changes in size, shape, and arrangement of the nanoparticles, using the layer potential techniques associated with the full Maxwell equations. We present an effective medium theory for resonant plasmonic systems and derive a condition on the volume fraction under which the Maxwell-Garnett theory is valid at plasmonic resonances.

  17. Geomaterial characterizations of full scale pavement test sections for mechanistic analysis and design

    CSIR Research Space (South Africa)

    Kwon, J

    2007-02-01

    Full Text Available Resilient modulus is a key input property of pavement foundation geomaterials, i.e., subgrade soil and base/subbase unbound aggregate, for the mechanistic-empirical design of flexible pavements. Recent research at the University of Illinois has...

  18. Full Moment Tensor Analysis Using First Motion Data at The Geysers Geothermal Field

    Science.gov (United States)

    Boyd, O.; Dreger, D. S.; Lai, V. H.; Gritto, R.

    2012-12-01

    Seismicity associated with geothermal energy production at The Geysers Geothermal Field in northern California has been increasing during the last forty years. We investigate source models of over fifty earthquakes with magnitudes ranging from Mw 3.5 up to Mw 4.5. We invert three-component, complete waveform data from broadband stations of the Berkeley Digital Seismic Network, the Northern California Seismic Network and the USA Array deployment (2005-2007) for the complete, six-element moment tensor. Some solutions are double-couple while others have substantial non-double-couple components. To assess the stability and significance of non-double-couple components, we use a suite of diagnostic tools including the F-test, Jackknife test, bootstrap and network sensitivity solution (NSS). The full moment tensor solutions of the studied events tend to plot in the upper half of the Hudson source type diagram where the fundamental source types include +CLVD, +LVD, tensile-crack, DC and explosion. Using the F-test to compare the goodness-of-fit values between the full and deviatoric moment tensor solutions, most of the full moment tensor solutions do not show a statistically significant improvement in fit over the deviatoric solutions. Because a small isotropic component may not significantly improve the fit, we include first motion polarity data to better constrain the full moment tensor solutions.

  19. Analysis of High Temperature Reactor Control Rod Worth for the Initial and Full Core

    Science.gov (United States)

    Oktajianto, Hammam; Setiawati, Evi; Anam, Khoirul; Sugito, Heri

    2017-01-01

    Control rod is one important component in a nuclear reactor. In nuclear reactor operations the control rod functions to shut down the reactor. This research analyses ten control rods worth of HTR (High Temperature Reactor) at initial and full core. The HTR in this research adopts HTR-10 China and HTR- of pebble bed. Core calculations are performed by using MCNPX code after modelling the entire parts of core in condition of ten control rods fully withdrawn, all control rods in with 20 cm ranges of depth and the use of one control rod. Pebble bed and moderator balls are distributed in the core zone using a Body Centred Cubic (BCC) lattice by ratio of 57:43. The research results are obtained that the use of one control rod will decrease the reactor criticality of 2.04±0.12 %Δk/k at initial core and 1.57±0.10 %Δk/k at full core. The deeper control rods are in, the lesser criticality of reactor is with reactivity of ten control rods of 16.41±0.11 %Δk/k at initial core and 15.43±0.11 %Δk/k at full core. The results show that the use of ten control rods at full core will keep achieving subcritical condition even though the reactivity is smaller than reactivity at initial core.

  20. Video analysis of dust events in full-tungsten ASDEX Upgrade

    NARCIS (Netherlands)

    Brochard, F.; Shalpegin, A.; Bardin, S.; Lunt, T.; Rohde, V.; Briançon, J. L.; Pautasso, G.; Vorpahl, C.; Neu, R.; ASDEX Upgrade team,

    2017-01-01

    Fast video data recorded during seven consecutive operation campaigns (2008–2012) in full-tungsten ASDEX Upgrade have been analyzed with an algorithm developed to automatically detect and track dust particles. A total of 2425 discharges have been analyzed, corresponding to 12 204 s of plasma

  1. Comparison of Test and Finite Element Analysis for Two Full-Scale Helicopter Crash Tests

    Science.gov (United States)

    Annett, Martin S.; Horta,Lucas G.

    2011-01-01

    Finite element analyses have been performed for two full-scale crash tests of an MD-500 helicopter. The first crash test was conducted to evaluate the performance of a composite deployable energy absorber under combined flight loads. In the second crash test, the energy absorber was removed to establish the baseline loads. The use of an energy absorbing device reduced the impact acceleration levels by a factor of three. Accelerations and kinematic data collected from the crash tests were compared to analytical results. Details of the full-scale crash tests and development of the system-integrated finite element model are briefly described along with direct comparisons of acceleration magnitudes and durations for the first full-scale crash test. Because load levels were significantly different between tests, models developed for the purposes of predicting the overall system response with external energy absorbers were not adequate under more severe conditions seen in the second crash test. Relative error comparisons were inadequate to guide model calibration. A newly developed model calibration approach that includes uncertainty estimation, parameter sensitivity, impact shape orthogonality, and numerical optimization was used for the second full-scale crash test. The calibrated parameter set reduced 2-norm prediction error by 51% but did not improve impact shape orthogonality.

  2. Similar familial underpinnings for full and subsyndromal pediatric bipolar disorder: A familial risk analysis.

    Science.gov (United States)

    Wozniak, Janet; Uchida, Mai; Faraone, Stephen V; Fitzgerald, Maura; Vaudreuil, Carrie; Carrellas, Nicholas; Davis, Jacqueline; Wolenski, Rebecca; Biederman, Joseph

    2017-05-01

    To examine the validity of subthreshold pediatric bipolar I disorder (BP-I), we compared the familial risk for BP-I in the child probands who had either full BP-I, subthreshold BP-I, ADHD, or were controls that neither had ADHD nor bipolar disorder. BP-I probands were youth aged 6-17 years meeting criteria for BP-I, full (N=239) or subthreshold (N=43), and also included were their first-degree relatives (N=687 and N=120, respectively). Comparators were youth with ADHD (N=162), controls without ADHD or bipolar disorder (N=136), and their first-degree relatives (N=511 and N=411, respectively). We randomly selected 162 non-bipolar ADHD probands and 136 non-bipolar, non-ADHD control probands of similar age and sex distribution to the BP-I probands from our case-control ADHD family studies. Psychiatric assessments were made by trained psychometricians using the Kiddie Schedule for Affective Disorders and Schizophrenia for School-Age Children Epidemiological Version (KSADS-E) and Structured Clinical Interview for DSM-IV (SCID) structured diagnostic interviews. We analyzed rates of bipolar disorder using multinomial logistic regression. Rates of full BP-I significantly differed between the four groups (χ(2)3 =32.72, P<.001): relatives of full BP-I probands and relatives of subthreshold BP-I probands had significantly higher rates of full BP-I than relatives of ADHD probands and relatives of control probands. Relatives of full BP-I, subthreshold BP-I, and ADHD probands also had significantly higher rates of major depressive disorder compared to relatives of control probands. Our results showed that youth with subthreshold BP-I had similarly elevated risk for BP-I and major depressive disorder in first-degree relatives as youth with full BP-I. These findings support the diagnostic continuity between subsyndromal and fully syndromatic states of pediatric BP-I disorder. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  3. Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

    NARCIS (Netherlands)

    Mol, Hans G.J.; Tienstra, Marc; Zomer, Paul

    2016-01-01

    Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application. The relevant aspects for GC-MS

  4. Screening in veterinary drug analysis and sports doping control based on full-scan, accurate-mass spectrometry

    NARCIS (Netherlands)

    Peters, R.J.B.; Stolker, A.A.M.; Mol, J.G.J.; Lommen, A.; Lyris, E.; Angelis, Y.S.; Vonaparti, A.; Stamou, M.; Georgakopoulos, C.G.; Nielen, M.W.F.

    2010-01-01

    A common trend in food contaminants and sports doping control is towards a limited number of targeted, full-scan, accurate-mass spectrometry (MS) methods based on time-of-flight (TOF) or Fourier-transform orbital trap (Orbitrap) mass analyzers. Retrospective analysis of the full-scan datasets of sig

  5. Design and analysis of carbon nanotube FET based quaternary full adders

    Institute of Scientific and Technical Information of China (English)

    Mohammad Hossein MOAIYERI; Shima SEDIGHIANI; Fazel SHARIFI; Keivan NAVI

    2016-01-01

    CMOS binary logic is limited by short channel effects, power density, and interconnection restrictions. The effective solution is non-silicon multiple-valued logic (MVL) computing. This study presents two high-performance quaternary full adder cells based on carbon nanotube field effect transistors (CNTFETs). The proposed designs use the unique properties of CNTFETs such as achieving a desired threshold voltage by adjusting the carbon nanotube diameters and having the same mobility as p-type and n-type devices. The proposed circuits were simulated under various test conditions using the Synopsys HSPICE simulator with the 32 nm Stanford comprehensive CNTFET model. The proposed designs have on average 32% lower delay, 68% average power, 83% energy consumption, and 77% static power compared to current state-of-the-art quaternary full adders. Simulation results indicated that the proposed designs are robust against process, voltage, and temperature variations, and are noise tolerant.

  6. RIGOROUS FULL-WAVE ANALYSIS OF THE BASE-STATION ANTENNAS

    Institute of Scientific and Technical Information of China (English)

    Chen Shengbing; Zhang Fushun; Jiao Yongchang; Sun Baohua

    2002-01-01

    Rigorous analysis of the Base-Station (BS) antennas with reflector is made in this letter. The wire-grid modeling of BS antenna is established. In order to improve the solution accuracy and efficiency, some efficient techniques such as three-term sinusoidal interpolation basis function and discrete wavelet transform are used. Numerical examples considered here are the typical vertically polarized and the dual-polarized BS antennas. The calculated results for the vertically polarized BS antenna are in good agreement with the measured data, which show that the analysis modeling used is accurate and reliable.

  7. Analysis of spin flip data in rings with nearly full Siberian Snakes

    Energy Technology Data Exchange (ETDEWEB)

    Mane, S.R. [Convergent Computing Inc., P.O. Box 561, Shoreham, NY 11786 (United States)], E-mail: srmane@optonline.net

    2009-04-01

    I calculate theoretical values to fit experimental measurements of spin flip resonance widths in rings with nearly full strength Siberian Snakes. Some measurements were made using an rf solenoid, and others using vertical field rf dipoles. In particular, the staff of the MIT-Bates Linear Accelerator Laboratory kindly made available to me additional unpublished data for the spin flipping of stored polarized electrons at 850 MeV using a vertical field rf dipole spin flipper.

  8. Full-Range Public Health Leadership, Part 2: Qualitative Analysis and Synthesis

    OpenAIRE

    Carlton, Erik L.; Holsinger, James W.; Martha C Riddell; Heather eBush

    2015-01-01

    Public health leadership is an important topic in the era of U. S. health reform, population health innovation, and health system transformation. This study utilized the full-range leadership model in order to examine public health leadership. We sought to understand local public health leadership from the perspective of local health department leaders and those who work with and for them. Public health leadership was explored through interviews and focus groups with directors (n=4) and s...

  9. Full-thickness tears of the supraspinatus tendon: A three-dimensional finite element analysis.

    Science.gov (United States)

    Quental, C; Folgado, J; Monteiro, J; Sarmento, M

    2016-12-08

    Knowledge regarding the likelihood of propagation of supraspinatus tears is important to allow an early identification of patients for whom a conservative treatment is more likely to fail, and consequently, to improve their clinical outcome. The aim of this study was to investigate the potential for propagation of posterior, central, and anterior full-thickness tears of different sizes using the finite element method. A three-dimensional finite element model of the supraspinatus tendon was generated from the Visible Human Project data. The mechanical behaviour of the tendon was fitted from experimental data using a transversely isotropic hyperelastic constitutive model. The full-thickness tears were simulated at the supraspinatus tendon insertion by decreasing the interface area. Tear sizes from 10% to 90%, in 10% increments, of the anteroposterior length of the supraspinatus footprint were considered in the posterior, central, and anterior regions of the tendon. For each tear, three finite element analyses were performed for a supraspinatus force of 100N, 200N, and 400N. Considering a correlation between tendon strain and the risk of tear propagation, the simulated tears were compared qualitatively and quantitatively by evaluating the volume of tendon for which a maximum strain criterion was not satisfied. The finite element analyses showed a significant impact of tear size and location not only on the magnitude, but also on the patterns of the maximum principal strains. The mechanical outcome of the anterior full-thickness tears was consistently, and significantly, more severe than that of the central or posterior full-thickness tears, which suggests that the anterior tears are at greater risk of propagating than the central or posterior tears.

  10. A novel genome-wide full- length kinesin prediction analysis reveals additional mammalian kinesins

    Institute of Scientific and Technical Information of China (English)

    XUE Yu; LIU Dan; FU Chuanhai; DOU Zhen; ZHOU Qing; YAO Xuebiao

    2006-01-01

    Kinesin superfamily of microtubule- based motor orchestrates a variety of cellular processes. Recent availability of mammalian genomes has enabled analyses of kinesins on the whole genome. Here we present a novel full-length kinesin prediction program (FKPP) for mammalian kinesin gene discovery based on a comparative genomics approach. Contrary to previous predictions of 94 kinesins, we identify a total of 134 potentially kinesin genes from mammalian genomes, including 45 from mouse, 45 from rat and 44 from human. In addition, FKPP synthesizes 25 potentially full-length mammalian kinesins based on the partial sequences in the database. Surprisingly, FKPP reveals that full-length human CENP-E contains 2701 aa rather than 2663 aa in the database. Experimentation using sequence specific antibody and cDNA sequencing of human CENP-E validates the accuracy of FKPP. Given the remarkable computing efficiency and accuracy of FKPP, we reclassify the mammalian kinesin superfamily. Since current databases contain many incomplete sequences, FKPP may provide a novel approach for molecular delineation of kinesins and other protein families.

  11. Evolution of the bamboos (Bambusoideae; Poaceae): a full plastome phylogenomic analysis.

    Science.gov (United States)

    Wysocki, William P; Clark, Lynn G; Attigala, Lakshmi; Ruiz-Sanchez, Eduardo; Duvall, Melvin R

    2015-03-18

    Bambusoideae (Poaceae) comprise three distinct and well-supported lineages: tropical woody bamboos (Bambuseae), temperate woody bamboos (Arundinarieae) and herbaceous bamboos (Olyreae). Phylogenetic studies using chloroplast markers have generally supported a sister relationship between Bambuseae and Olyreae. This suggests either at least two origins of the woody bamboo syndrome in this subfamily or its loss in Olyreae. Here a full chloroplast genome (plastome) phylogenomic study is presented using the coding and noncoding regions of 13 complete plastomes from the Bambuseae, eight from Olyreae and 10 from Arundinarieae. Trees generated using full plastome sequences support the previously recovered monophyletic relationship between Bambuseae and Olyreae. In addition to these relationships, several unique plastome features are uncovered including the first mitogenome-to-plastome horizontal gene transfer observed in monocots. Phylogenomic agreement with previous published phylogenies reinforces the validity of these studies. Additionally, this study presents the first published plastomes from Neotropical woody bamboos and the first full plastome phylogenomic study performed within the herbaceous bamboos. Although the phylogenomic tree presented in this study is largely robust, additional studies using nuclear genes support monophyly in woody bamboos as well as hybridization among previous woody bamboo lineages. The evolutionary history of the Bambusoideae could be further clarified using transcriptomic techniques to increase sampling among nuclear orthologues and investigate the molecular genetics underlying the development of woody and floral tissues.

  12. Design and analysis of a high-performance CNFET-based Full Adder

    Science.gov (United States)

    Moaiyeri, Mohammad Hossein; Faghih Mirzaee, Reza; Navi, Keivan; Momeni, Amir

    2012-01-01

    This article presents a high-speed and high-performance Carbon Nanotube Field Effect Transistor (CNFET) based Full Adder cell for low-voltage applications. The proposed Full Adder cell is composed of two separate modules with identical hardware configurations which generate the Sum and C out signals in a parallel manner. The great advantage of the proposed structure is its very short critical path which is composed of only two carbon nanotube pass-transistors. This design also takes advantage of the unique properties of metal oxide semiconductor field effect transistor-like CNFETs such as the feasibility of adjusting the threshold voltage of a CNFET by adjusting the diameter of its nanotubes to correct the voltage levels as well as to achieve a high performance. Comprehensive experiments are performed in various situations to evaluate the performance of the proposed design. Simulations are carried out using Synopsys HSPICE with 32-nm Complementary Metal Oxide Semiconductor (CMOS) and 32-nm CNFET technologies. The simulation results demonstrate the superiority of the proposed design in terms of speed, power consumption, power delay product, and less susceptibility to process variations, compared to other classical and modern CMOS and CNFET-based Full Adder cells.

  13. Procedure for conducting probabilistic safety assessment: level 1 full power internal event analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Won Dae; Lee, Y. H.; Hwang, M. J. [and others

    2003-07-01

    This report provides guidance on conducting a Level I PSA for internal events in NPPs, which is based on the method and procedure that was used in the PSA for the design of Korea Standard Nuclear Plants (KSNPs). Level I PSA is to delineate the accident sequences leading to core damage and to estimate their frequencies. It has been directly used for assessing and modifying the system safety and reliability as a key and base part of PSA. Also, Level I PSA provides insights into design weakness and into ways of preventing core damage, which in most cases is the precursor to accidents leading to major accidents. So Level I PSA has been used as the essential technical bases for risk-informed application in NPPs. The report consists six major procedural steps for Level I PSA; familiarization of plant, initiating event analysis, event tree analysis, system fault tree analysis, reliability data analysis, and accident sequence quantification. The report is intended to assist technical persons performing Level I PSA for NPPs. A particular aim is to promote a standardized framework, terminology and form of documentation for PSAs. On the other hand, this report would be useful for the managers or regulatory persons related to risk-informed regulation, and also for conducting PSA for other industries.

  14. Assessing the Dimensionality of the GMAT Verbal and Quantitative Measures Using Full Information Factor Analysis.

    Science.gov (United States)

    Kingston, Neal

    When the three-parameter logistic model and item response theory are used to analyze Graduate Management Admission Test (GMAT) data, there are problems with the assumption of unidimensionality. Linear factor analytic models, exploratory factor analysis programs, and the comparison of item parameter estimates for heterogeneous and homogeneous…

  15. Far-field properties and beam quality of vectorial Hermite-Laguerre-Gaussian beams beyond the paraxial approximation

    Science.gov (United States)

    Kang, Xiaoping; He, Zhong; Lü, Baida

    2007-07-01

    The far-field properties and beam quality of vectorial nonparaxial Hermite-Laguerre-Gaussian (HLG) beams are studied in detail, where, instead of the second-order-moments-based M2 factor, the extended power in the bucket (PIB) and βparameter are used to characterize the beam quality in the far field and the intensity in the formulae is replaced by the z component of the time-averaged Poynting vector . It is found that the PIB and βparameter of vectorial nonparaxial HLG beams depend on the mode indices n, m, αparameter and waist-width-to-wavelength ratio w0/ λ and the PIB and βparameter are additionally dependent on the bucket's size taken.

  16. Vectorial diffusion for facile solution-processed self-assembly of insoluble semiconductors: a case study on metal phthalocyanines.

    Science.gov (United States)

    Wang, Chengliang; Fang, Yaoguo; Wen, Liaoyong; Zhou, Min; Xu, Yang; Zhao, Huaping; De Cola, Luisa; Hu, Wenping; Lei, Yong

    2014-08-25

    Solution processibility is one of the most intriguing properties of organic semiconductors. However, it is difficult to find a suitable solvent and solution process for most semiconductors. For example, metal phthalocyanines (MPcs) are only soluble in non-volatile solvents, which prevent their applications from solution process. For the first time, vectorial diffusion is utilized for solution processing of MPcs. The obtained large F16CuPc and α-phase CuPc crystals and the efficient phase separation of them suggest the vectorial diffusion process is as slow as a self-assembly process, which is helpful to yield large crystals and purify the semiconductors. This method, which only uses common commercial solvents without any complex and expensive instruments and high-temperature operation, provides a facile approach for purification of organic semiconductors and growth of their crystals in large quantities.

  17. Generation and Analysis of Full-length cDNA Sequences from Elephant Shark (Callorhinchus milii)

    KAUST Repository

    Kodzius, Rimantas

    2009-03-17

    Cartilaginous fishes are the oldest living group of jawed vertebrates and therefore is an important group for understanding the evolution of vertebrate genomes including the human genome. Our laboratory has proposed elephant shark (C. milii) as a model cartilaginous fish genome because of its relatively small genome size (910 Mb). The whole genome of C. milii is being sequenced (first cartilaginous fish genome to be sequenced completely). To characterize the transcriptome of C. milii and to assist in annotating exon-intron boundaries, transcriptional start sites and alternatively spliced transcripts, we are generating full-length cDNA sequences from C. milii.

  18. Pedigree analysis: One teaching strategy to incorporate genetics into a full FNP program.

    Science.gov (United States)

    Schumacher, Gretchen; Conway, Alice E; Sparlin, Judith A

    2006-05-01

    The successful completion of the genome project in April 2003 and explosion of genetic knowledge is impacting healthcare at a dramatic rate. All healthcare providers need to update themselves on genetics in order to provide comprehensive care. This article describes a national grant obtained to educate faculty regarding incorporating genetics into courses. It also presents an innovate method for incorporating genetics into a full Family Nurse Practitioner (FNP) curriculum. Student responses and guidelines for one assignment are included. Utilizing this type of assignment in FNP courses is beneficial to both students and faculty. With more FNPs assessing patterns for illness in families, primary prevention and earlier intervention in primary care can be achieved.

  19. Getting full control of canonical correlation analysis with the AutoBiplot.CCA function

    Science.gov (United States)

    Alves, M. Rui

    2016-06-01

    Function AutoBiplot.CCA was built in R language. Given two multivariate data sets, this function carries out a conventional canonical correlation analysis, followed by the automatic production of predictive biplots based on the accuracy of readings as assessed by a mean standard predictive error and a user defined tolerance value. As the user's intervention is mainly restricted to the choice of the magnitude of the t.axis value, common misinterpretations, overestimations and adjustments between outputs and personal beliefs are avoided.

  20. An analysis of student satisfaction: full-time versus part-time students

    OpenAIRE

    Moro-Egido, Ana; Panad??s, Judith

    2008-01-01

    This paper examines how students??? characteristics affect their level of satisfaction with their academic degree. For this analysis we draw data from a survey answered by graduate students. This survey was conducted at a public university in Spain from 2001 to 2004. The fact that students simultaneously work and study emerges as one of the most important determinants of student satisfaction. In particular, our results show that alumni who had a part-time job while they were studying are more...

  1. Exploration of Integrated Visible to Near-, Shortwave-, and Longwave-Infrared (Full-Range) Spectral Analysis

    Science.gov (United States)

    2014-09-01

    classification approach. 20 Warner and Nerry (2009) combined HSI VNIR-SWIR data with MSI LWIR to explore urban land-cover classification of...features across the EM spectrum. Additional benefits may be revealed if utilizing integrated analysis on urban scenes containing higher variability of...Sutley, S. J. … Gent, C. A. (2003). Imaging spectroscopy: Earth and planetary remote sensing with the USGS Tetracorder and expert systems. Journal of

  2. Causal diagrams and multivariate analysis I: a quiver full of arrows.

    Science.gov (United States)

    Jupiter, Daniel C

    2014-01-01

    How do we know which variables we should include in our multivariate analyses? What role does each variable play in our understanding of the analysis? In this article I begin a discussion of these issues and describe 2 different types of studies for which this problem must be handled in different ways. Copyright © 2014 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

  3. Aedes Taeniorhynchus Vectorial Capacity Informs A Pre-Emptive Assessment Of West Nile Virus Establishment In Galápagos

    OpenAIRE

    Gillian Eastwood; Goodman, Simon J.; Cunningham, Andrew A.; Kramer, Laura D.

    2013-01-01

    Increased connectivity with the mainland has led to the arrival of many invasive species to the Galápagos Islands, including novel pathogens, threatening the archipelago's unique fauna. Here we consider the potential role of the mosquito Aedes taeniorhynchus in maintaining the flavivirus West Nile virus [WNV] should it reach the islands. We report on three components of vectorial capacity - vector competency, distributional abundance and host-feeding. In contrast to USA strains, Galápagos A. ...

  4. Full Waveform Analysis for Long-Range 3D Imaging Laser Radar

    Directory of Open Access Journals (Sweden)

    Wallace AndrewM

    2010-01-01

    Full Text Available The new generation of 3D imaging systems based on laser radar (ladar offers significant advantages in defense and security applications. In particular, it is possible to retrieve 3D shape information directly from the scene and separate a target from background or foreground clutter by extracting a narrow depth range from the field of view by range gating, either in the sensor or by postprocessing. We discuss and demonstrate the applicability of full-waveform ladar to produce multilayer 3D imagery, in which each pixel produces a complex temporal response that describes the scene structure. Such complexity caused by multiple and distributed reflection arises in many relevant scenarios, for example in viewing partially occluded targets, through semitransparent materials (e.g., windows and through distributed reflective media such as foliage. We demonstrate our methodology on 3D image data acquired by a scanning time-of-flight system, developed in our own laboratories, which uses the time-correlated single-photon counting technique.

  5. LS-DYNA Analysis of a Full-Scale Helicopter Crash Test

    Science.gov (United States)

    Annett, Martin S.

    2010-01-01

    A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26 ft/sec and 40 ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated LS-DYNA finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test and continuing through post test validation.

  6. Full Factorial Experimental Design Analysis of Reactive Dye Removal by Carbon Adsorption

    Directory of Open Access Journals (Sweden)

    N. Özbay

    2013-01-01

    Full Text Available The objective of this study was to investigate the removal of Remazol Yellow dye from aqueous solutions by adsorption on activated carbon prepared by chemical activation of sunflower seed cake. It was found that the carbon content of biomass increases up to 65.12% after activation and carbonization processes. The maximum percentage dye removal was obtained as 82.12% with 0.4 g/50 mL adsorbent dosage at 313 K. The Langmuir model showed the best fit with equilibrium isotherm data. The interactions were evaluated with respect to both pseudo-first-order and pseudo-second-order reaction kinetics. The adsorption process was found to follow the pseudo-second-order model. To optimize the operating conditions, the effects of pH, adsorbent dosage, and initial dye concentration were investigated by full factorial experimental design method; adsorbent dosage was found as the most significant factor with lower than 95% confidence level. The obtained results are very promising since (i the utilization of sunflower seed cake activated carbon (SSCAC played a critical role in the adsorption of dye; (ii sunflower seed cake was an intriguing, low-cost, and easily available material. It can be an alternative adsorbent precursor for more expensive adsorbents used for Remazol Yellow (RY removal.

  7. [Analysis of sub-typing in full-frequency sudden deafness].

    Science.gov (United States)

    Liang, Zhen; Yu, Li-sheng; Xia, Rui-ming

    2010-04-01

    To explore the relationship between the sub-typing of full-frequency sudden deafness and its effect in treatment. A series of 87 cases that have full-frequency sudden deafness were studied from Aug, 2005 to Mar, 2008. All cases were treated with methylprednisolone, Batroxobin and Xueshuantong. Based on the frequency of hearing loss, the objectives were divided into sudden-drop-down type and slow-drop-down type. The effective percentage and significant effective percentage in sudden-drop-down type were 84.4% (27/32) and 68.8% (22/32), respectively. The effective percentage and significant effective percentage in slow-drop-down type were 52.7% (29/55) and 32.7% (18/55), respectively. Slow-drop-down type showed a higher effective and significant effective percentage respectively (P sudden deafness needs a further classification. According to the frequency of hearing loss, it can be divided into sudden-drop-down and slow-drop-down type. According to the degree of hearing loss, it can be divided into flat-type and profound-type. It would be appropriate to using 90 dB(average hearing threshold) as a criteria for the classification of hearing loss.

  8. The membrane-topogenic vectorial behaviour of Nrf1 controls its post-translational modification and transactivation activity.

    Science.gov (United States)

    Zhang, Yiguo; Hayes, John D

    2013-01-01

    The integral membrane-bound Nrf1 transcription factor fulfils important functions in maintaining cellular homeostasis and organ integrity, but how it is controlled vectorially is unknown. Herein, creative use of Gal4-based reporter assays with protease protection assays (GRAPPA), and double fluorescence protease protection (dFPP), reveals that the membrane-topogenic vectorial behaviour of Nrf1 dictates its post-translational modification and transactivation activity. Nrf1 is integrated within endoplasmic reticulum (ER) membranes through its NHB1-associated TM1 in cooperation with other semihydrophobic amphipathic regions. The transactivation domains (TADs) of Nrf1, including its Asn/Ser/Thr-rich (NST) glycodomain, are transiently translocated into the ER lumen, where it is glycosylated in the presence of glucose to become a 120-kDa isoform. Thereafter, the NST-adjoining TADs are partially repartitioned out of membranes into the cyto/nucleoplasmic side, where Nrf1 is subject to deglycosylation and/or proteolysis to generate 95-kDa and 85-kDa isoforms. Therefore, the vectorial process of Nrf1 controls its target gene expression.

  9. Full scale numerical analysis of high performance concrete columns designed to withstand severe blast impact

    DEFF Research Database (Denmark)

    Riisgaard, Benjamin; Georgakis, Christos; Stang, Henrik;

    2007-01-01

    Polymer reinforced Compact Reinforced Composite, PCRC, is a Fiber reinforced Densified Small Particle system, FDSP, combined with a high strength longitudinal flexural rebar arrangement laced together with polymer lacing to avoid shock initiated disintegration of the structural element under blast...... load. Scaled experimental and numerical results of PCRC columns (200x200x1600mm) subjected to close-in detonation are presented in this paper. Based on these results and the use of geometrical scaling lows, a full scale column (800x800x6400mm) is designed and verified numerically to withstand 486.5 kg...... of PETN (85/15) High Explosives at stand off 1600 mm. Additionally, a LS-DYNA material model suitable for predicting the response of Polymer reinforced Compact Reinforced Concrete improved for close-in detonation and a description of the LS-DYNA multi-material Eulerian method for modeling the blast event...

  10. Classification and analysis of human ovarian tissue using full field optical coherence tomography.

    Science.gov (United States)

    Nandy, Sreyankar; Sanders, Melinda; Zhu, Quing

    2016-12-01

    In this study, a full field optical coherence tomography (FFOCT) system was used to analyze and classify normal and malignant human ovarian tissue. 14 ovarian tissue samples (7 normal, 7 malignant) were imaged with the FFOCT system and five features were extracted by analyzing the normalized image histogram from 56 FFOCT images, based on the differences in the morphology of the normal and malignant tissue samples. A generalized linear model (GLM) classifier was trained using 36 images, and sensitivity of 95.3% and specificity of 91.1% was obtained. 20 images were used to test the model, and a sensitivity of 91.6% and specificity of 87.7% was obtained.

  11. Molecular analysis of methanogens involved in methanogenic degradation of tetramethylammonium hydroxide in full-scale bioreactors.

    Science.gov (United States)

    Whang, Liang-Ming; Hu, Tai-Ho; Liu, Pao-Wen Grace; Hung, Yu-Ching; Fukushima, Toshikazu; Wu, Yi-Ju; Chang, Shao-Hsiung

    2015-02-01

    This study investigated methanogenic communities involved in degradation of tetramethylammonium hydroxide (TMAH) in three full-scale bioreactors treating TMAH-containing wastewater. Based on the results of terminal-restriction fragment-length polymorphism (T-RFLP) and quantitative PCR analyses targeting the methyl-coenzyme M reductase alpha subunit (mcrA) genes retrieved from three bioreactors, Methanomethylovorans and Methanosarcina were the dominant methanogens involved in the methanogenic degradation of TMAH in the bioreactors. Furthermore, batch experiments were conducted to evaluate mcrA messenger RNA (mRNA) expression during methanogenic TMAH degradation, and the results indicated that a higher level of TMAH favored mcrA mRNA expression by Methansarcina, while Methanomethylovorans could only express considerable amount of mcrA mRNA at a lower level of TMAH. These results suggest that Methansarcina is responsible for methanogenic TMAH degradation at higher TMAH concentrations, while Methanomethylovorans may be important at a lower TMAH condition.

  12. Resonant transmission in one-dimensional quantum mechanics with two independent point interactions: Full parameter analysis

    Science.gov (United States)

    Konno, Kohkichi; Nagasawa, Tomoaki; Takahashi, Rohta

    2017-10-01

    We discuss the scattering of a quantum particle by two independent successive point interactions in one dimension. The parameter space for two point interactions is given by U(2) × U(2) , which is described by eight real parameters. We perform an analysis of perfect resonant transmission on the whole parameter space. By investigating the effects of the two point interactions on the scattering matrix of plane wave, we find the condition under which perfect resonant transmission occurs. We also provide the physical interpretation of the resonance condition.

  13. Energy Sources and Systems Analysis: 40 South Lincoln Redevelopment District (Full Report)

    Energy Technology Data Exchange (ETDEWEB)

    2011-08-01

    This report presents the results of a case study to analyze district energy systems for their potential use in a project that involves redeveloping 270 units of existing public housing, along with other nearby sites. When complete, the redevelopment project will encompass more than 900 mixed-income residential units, commercial and retail properties, and open space. The analysis estimated the hourly heating, cooling, domestic hot water, and electric loads required by the community; investigated potential district system technologies to meet those needs; and researched available fuel sources to power such systems.

  14. Sequencing, mapping, and analysis of 27,455 maize full-length cDNAs.

    Directory of Open Access Journals (Sweden)

    Carol Soderlund

    2009-11-01

    Full Text Available Full-length cDNA (FLcDNA sequencing establishes the precise primary structure of individual gene transcripts. From two libraries representing 27 B73 tissues and abiotic stress treatments, 27,455 high-quality FLcDNAs were sequenced. The average transcript length was 1.44 kb including 218 bases and 321 bases of 5' and 3' UTR, respectively, with 8.6% of the FLcDNAs encoding predicted proteins of fewer than 100 amino acids. Approximately 94% of the FLcDNAs were stringently mapped to the maize genome. Although nearly two-thirds of this genome is composed of transposable elements (TEs, only 5.6% of the FLcDNAs contained TE sequences in coding or UTR regions. Approximately 7.2% of the FLcDNAs are putative transcription factors, suggesting that rare transcripts are well-enriched in our FLcDNA set. Protein similarity searching identified 1,737 maize transcripts not present in rice, sorghum, Arabidopsis, or poplar annotated genes. A strict FLcDNA assembly generated 24,467 non-redundant sequences, of which 88% have non-maize protein matches. The FLcDNAs were also assembled with 41,759 FLcDNAs in GenBank from other projects, where semi-strict parameters were used to identify 13,368 potentially unique non-redundant sequences from this project. The libraries, ESTs, and FLcDNA sequences produced from this project are publicly available. The annotated EST and FLcDNA assemblies are available through the maize FLcDNA web resource (www.maizecdna.org.

  15. Full phase analysis of portland clinker by penetrating synchrotron powder diffraction.

    Science.gov (United States)

    de la Torre, A G; Cabeza, A; Calvente, A; Bruque, S; Aranda, M A

    2001-01-15

    Fabrication of portland cements commonly depends on X-ray fluorescence (XRF), which measures the elemental compositions. XRF is used to adjust the raw material proportions and to control the process conditions. However, to predict the mechanical strength of the resulting concrete, it is essential to know the phase composition which is, so far, indirectly inferred by the Bogue method. Here, we report a phase analysis of an industrial portland clinker containing six crystalline phases, Ca3SiO5, Ca2SiO4, Ca4Al2Fe2O10, Ca3Al2O6, NaK3(SO4)2, and CaO, by Rietveld refinement of synchrotron X-ray powder diffraction data (lambda = 0.442377 A). Even the minor component, CaO 0.45(2)%, was readily analyzed. We have also carried out a phase study of the same clinker with laboratory X-rays to characterize the changes in the detection limit and errors. Furthermore, by adding a suitable crystalline standard to the same clinker, we have determined the overall amorphous phase content. The procedure established for this state-of-the-art phase analysis shows the high precision that can be achieved by using penetrating X-rays, which is of interest not only in cement chemistry but in other industrially important multiphase systems such as slags, superalloys, or catalysts.

  16. Full dynamical analysis of anisotropic scalar-field cosmology with arbitrary potentials

    CERN Document Server

    Fadragas, Carlos R; Saridakis, Emmanuel N

    2013-01-01

    We perform a detailed dynamical analysis of anisotropic scalar-field cosmologies, and in particular of the most significant Kantowski-Sachs, Bianchi I and Bianchi III cases. We follow the new and powerful method of $f$-devisers, which allows us to perform the whole analysis for arbitrary potentials. Thus, one can just substitute the specific potential form in the final results and obtain the corresponding behavior, without the need of new calculations. We find a very rich behavior, and amongst others the universe can result in isotropized solutions with observables in agreement with observations, such as de Sitter, quintessence-like, or stiff-dark energy solutions. Additionally, in the case of Kantowski-Sachs geometry we find that a cosmological bounce and turnaround are realized in a part of the parameter-space. Finally, applying the general results to the well-studied exponential and power-law potentials, we find that some of the general stable solutions disappear. This feature may be an indication that suc...

  17. Analysis and Prediction of Ice Shedding for a Full-Scale Heated Tail Rotor

    Science.gov (United States)

    Kreeger, Richard E.; Work, Andrew; Douglass, Rebekah; Gazella, Matthew; Koster, Zakery; Turk, Jodi

    2016-01-01

    When helicopters are to fly in icing conditions, it is necessary to consider the possibility of ice shed from the rotor blades. In 2013, a series of tests were conducted on a heated tail rotor at NASA Glenn's Icing Research Tunnel (IRT). The tests produced several shed events that were captured on camera. Three of these shed events were captured at a sufficiently high frame rate to obtain multiple images of the shed ice in flight that had a sufficiently long section of shed ice for analysis. Analysis of these shed events is presented and compared to an analytical Shedding Trajectory Model (STM). The STM is developed and assumes that the ice breaks off instantly as it reaches the end of the blade, while frictional and viscous forces are used as parameters to fit the STM. The trajectory of each shed is compared to that predicted by the STM, where the STM provides information of the shed group of ice as a whole. The limitations of the model's underlying assumptions are discussed in comparison to experimental shed events.

  18. Data Structure for Porgressive Visualisation and Edition of Vectorial Geospatial Data

    Science.gov (United States)

    Gaillard, J.; Peytavie, A.; Gesquière, G.

    2016-10-01

    3D mock-ups of cities are becoming an increasingly common tool for urban planning. Sharing the mock-up is still a challenge since the volume of data is so high. Furthermore, the recent surge in low-end, mobile devices requires developers to carefully control the amount of data they process. In this paper, we present a hierarchical data structure that allows the streaming of vectorial data. Loosely based on a quadtree, the structure stores the data in tiles and is organised following a weight function which allows the most relevant data to be displayed first. The relevance of a feature can be measured by its geometry and semantic attributes, and can vary depending on the application or client type. Tiles can be limited in size (number of features or triangles) for the client to be able to control resource consumption. The article also presents algorithms for the addition or removal of features in the data structure, opening the path for the interactive edition of city data stored in a database.

  19. Intraflagellar transport is required for the vectorial movement of TRPV channels in the ciliary membrane.

    Science.gov (United States)

    Qin, Hongmin; Burnette, Dylan T; Bae, Young-Kyung; Forscher, Paul; Barr, Maureen M; Rosenbaum, Joel L

    2005-09-20

    The membranes of all eukaryotic motile (9 + 2) and immotile primary (9 + 0) cilia harbor channels and receptors involved in sensory transduction (reviewed by). These membrane proteins are transported from the cytoplasm onto the ciliary membrane by vesicles targeted for exocytosis at a point adjacent to the ciliary basal body. Here, we use time-lapse fluorescence microscopy to demonstrate that select GFP-tagged sensory receptors undergo rapid vectorial transport along the entire length of the cilia of Caenorhabditis elegans sensory neurons. Transient receptor potential vanilloid (TRPV) channels OSM-9 and OCR-2 move in ciliary membranes at rates comparable to the intraflagellar transport (IFT) machinery located between the membrane and the underlying axonemal microtubules. OSM-9 motility is disrupted in certain IFT mutant backgrounds. Surprisingly, motility of transient receptor potential polycystin (TRPP) channel PKD-2 (polycystic kidney disease-2), a mechano-receptor, was not detected. Our study demonstrates that IFT, previously shown to be necessary for transport of axonemal components, is also involved in the motility of TRPV membrane protein movement along cilia of C. elegans sensory cells.

  20. Invasiveness of Aedes aegypti and Aedes albopictus and Vectorial Capacity for Chikungunya Virus.

    Science.gov (United States)

    Lounibos, Leon Philip; Kramer, Laura D

    2016-12-15

    In this review, we highlight biological characteristics of Aedes aegypti and Aedes albopictus, 2 invasive mosquito species and primary vectors of chikungunya virus (CHIKV), that set the tone of these species' invasiveness, vector competence, and vectorial capacity (VC). The invasiveness of both species, as well as their public health threats as vectors, is enhanced by preference for human blood. Vector competence, characterized by the efficiency of an ingested arbovirus to replicate and become infectious in the mosquito, depends largely on vector and virus genetics, and most A. aegypti and A. albopictus populations thus far tested confer vector competence for CHIKV. VC, an entomological analog of the pathogen's basic reproductive rate (R0), is epidemiologically more important than vector competence but less frequently measured, owing to challenges in obtaining valid estimates of parameters such as vector survivorship and host feeding rates. Understanding the complexities of these factors will be pivotal in curbing CHIKV transmission. © The Author 2016. Published by Oxford University Press for the Infectious Diseases Society of America. All rights reserved. For permissions, e-mail journals.permissions@oup.com.

  1. Vectorial Structure of Non-Paraxial Linearly Polarized Gaussian Beam in Far Field

    Institute of Scientific and Technical Information of China (English)

    ZHOU Guo-Quan; CHEN Liang; NI Yong-Zhou

    2006-01-01

    @@ According to the vectorial structure of non-paraxial electromagnetic beams and the method of stationary phase,the analytical TE and TM terms of non-paraxial linearly polarized Gaussian beam are presented in the far field.The influence of linearly polarized angle on the relative energy flux distributions of the whole beam and its TE and TM terms is studied. The beam spot of the TE term is perpendicular to the direction of linearly polarized angle, while that of the TM term coincides with the direction of linearly polarized angle. The whole beam spot is elliptical, and the long axis is located at the direction of linearly polarized angle. The relative energy flux distribution of the TE term is relatively centralized in the direction perpendicular to the linearly polarized angle.While that of the TM term is relatively centralized in the direction of linearly polarized angle. To obtain the isolated TM and TE terms, a polarizer should be put at the long and the short axis of the whole beam. spot,respectively.

  2. Vectorial Command of Induction Motor Pumping System Supplied by a Photovoltaic Generator

    Science.gov (United States)

    Makhlouf, Messaoud; Messai, Feyrouz; Benalla, Hocine

    2011-01-01

    With the continuous decrease of the cost of solar cells, there is an increasing interest and needs in photovoltaic (PV) system applications following standard of living improvements. Water pumping system powered by solar-cell generators are one of the most important applications. The fluctuation of solar energy on one hand, and the necessity to optimise available solar energy on the other, it is useful to develop new efficient and flexible modes to control motors that entrain the pump. A vectorial control of an asynchronous motor fed by a photovoltaic system is proposed. This paper investigates a photovoltaic-electro mechanic chain, composed of a PV generator, DC-AC converter, a vector controlled induction motor and centrifugal pump. The PV generator is forced to operate at its maximum power point by using an appropriate search algorithm integrated in the vector control. The optimization is realized without need to adding a DC-DC converter to the chain. The motor supply is also ensured in all insolation conditions. Simulation results show the effectiveness and feasibility of such an approach.

  3. Analysis of Full Charge Reconstruction Algorithms for X-Ray Pixelated Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Baumbaugh, A.; /Fermilab; Carini, G.; /SLAC; Deptuch, G.; /Fermilab; Grybos, P.; /AGH-UST, Cracow; Hoff, J.; /Fermilab; Siddons, P., Maj.; /Brookhaven; Szczygiel, R.; /AGH-UST, Cracow; Trimpl, M.; Yarema, R.; /Fermilab

    2012-05-21

    Existence of the natural diffusive spread of charge carriers on the course of their drift towards collecting electrodes in planar, segmented detectors results in a division of the original cloud of carriers between neighboring channels. This paper presents the analysis of algorithms, implementable with reasonable circuit resources, whose task is to prevent degradation of the detective quantum efficiency in highly granular, digital pixel detectors. The immediate motivation of the work is a photon science application requesting simultaneous timing spectroscopy and 2D position sensitivity. Leading edge discrimination, provided it can be freed from uncertainties associated with the charge sharing, is used for timing the events. Analyzed solutions can naturally be extended to the amplitude spectroscopy with pixel detectors.

  4. Analysis of full charge reconstruction algorithms for x-ray pixelated detectors

    Energy Technology Data Exchange (ETDEWEB)

    Baumbaugh, A.; /Fermilab; Carini, G.; /SLAC; Deptuch, G.; /Fermilab; Grybos, P.; /AGH-UST, Cracow; Hoff, J.; /Fermilab; Siddons, P., Maj.; /Brookhaven; Szczygiel, R.; /AGH-UST, Cracow; Trimpl, M.; Yarema, R.; /Fermilab

    2011-11-01

    Existence of the natural diffusive spread of charge carriers on the course of their drift towards collecting electrodes in planar, segmented detectors results in a division of the original cloud of carriers between neighboring channels. This paper presents the analysis of algorithms, implementable with reasonable circuit resources, whose task is to prevent degradation of the detective quantum efficiency in highly granular, digital pixel detectors. The immediate motivation of the work is a photon science application requesting simultaneous timing spectroscopy and 2D position sensitivity. Leading edge discrimination, provided it can be freed from uncertainties associated with the charge sharing, is used for timing the events. Analyzed solutions can naturally be extended to the amplitude spectroscopy with pixel detectors.

  5. Comprehensive Analysis of the Green-to-Blue Photoconversion of Full-Length Cyanobacteriochrome Tlr0924

    Science.gov (United States)

    Hardman, Samantha J.O.; Hauck, Anna F.E.; Clark, Ian P.; Heyes, Derren J.; Scrutton, Nigel S.

    2014-01-01

    Cyanobacteriochromes are members of the phytochrome superfamily of photoreceptors and are of central importance in biological light-activated signaling mechanisms. These photoreceptors are known to reversibly convert between two states in a photoinitiated process that involves a basic E/Z isomerization of the bilin chromophore and, in certain cases, the breakage of a thioether linkage to a conserved cysteine residue in the bulk protein structure. The exact details and timescales of the reactions involved in these photoconversions have not been conclusively shown. The cyanobacteriochrome Tlr0924 contains phycocyanobilin and phycoviolobilin chromophores, both of which photoconvert between two species: blue-absorbing and green-absorbing, and blue-absorbing and red-absorbing, respectively. Here, we followed the complete green-to-blue photoconversion process of the phycoviolobilin chromophore in the full-length form of Tlr0924 over timescales ranging from femtoseconds to seconds. Using a combination of time-resolved visible and mid-infrared transient absorption spectroscopy and cryotrapping techniques, we showed that after photoisomerization, which occurs with a lifetime of 3.6 ps, the phycoviolobilin twists or distorts slightly with a lifetime of 5.3 μs. The final step, the formation of the thioether linkage with the protein, occurs with a lifetime of 23.6 ms. PMID:25418104

  6. Isobolographic analysis for combinations of a full and partial agonist: curved isoboles.

    Science.gov (United States)

    Grabovsky, Yury; Tallarida, Ronald J

    2004-09-01

    Combinations of drugs are frequently used therapeutically to achieve an enhanced effect without using an excess quantity of either agent. If the drugs exert overtly similar action, e.g., two analgesics, the effect of the combination may be tested for additivity, i.e., an effect level that is achieved based on the individual drug potencies. But combinations of agonists will sometimes display either superadditive (synergistic) or subadditive responses. Whether the two agonists are both drugs, or a combination of a drug and an endogenous chemical, there is interest in characterizing the interaction to determine whether it departs from additivity because quantitative information of this kind, aside from its therapeutic importance, may also illuminate mechanism. A common method for this characterization uses the isobologram. This is a plot in rectangular coordinates of dose combinations (a,b) that produce the same effect level (often taken to be 50% of the maximum). In its usual form, this plot is constructed as a straight line (of additivity) connecting intercepts that represent the individually effective doses, e.g., ED50 values of each. This line is the reference for distinguishing additive from nonadditive interactions accordingly as the tested combination is on or off this line. Discussed here are the assumptions that underlie this linear plot. Specifically we show that a combination of drugs with a variable potency ratio, exemplified by a full and a partial agonist, lead to curvilinear isoboles of additivity that may erroneously be attributed to either synergism or subadditivity.

  7. Qualitative and quantitative analysis of extracellular polymeric substances in partial nitrification and full nitrification reactors.

    Science.gov (United States)

    Wei, Dong; Yan, Tao; Zhang, Keyi; Chen, Ya; Wu, Na; Du, Bin; Wei, Qin

    2017-09-01

    In present study, two column-type sequencing batch reactors with alternative anoxic/aerobic phases were operated and compared under partial nitrification and full nitrification modes by controlling different dissolved oxygen (DO) conditions. During steady state, the characterizations of extracellular polymeric substances (EPS) from two reactors were qualitatively and quantitatively analyzed through chemical and spectroscopic approaches. Data implied that partial nitrification reactor had relatively higher total nitrogen (TN) removal efficiency and loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS) contents. According to excitation emission matrix (EEM) spectra, LB-EPS and TB-EPS from two kinds of reactors expressed similar fluorescence peak locations but different intensities. Fluorescence regional integration (FRI) further suggested that Region IV was the main fraction in both types of EPS fractions. Moreover, TB-EPS exhibited a greater number of molecular weight fractions than those of LB-EPS. Both EPS fractions had similar functional groups, which represented the complex nature of EPS compositions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Phase defect analysis with actinic full-field EUVL mask blank inspection

    Science.gov (United States)

    Yamane, Takeshi; Tanaka, Toshihiko; Terasawa, Tsuneo; Suga, Osamu

    2011-11-01

    We had developed an actinic full-field inspection system to detect multilayer phase-defects with dark field imaging. Regarding the actinic inspection of native defects, the influence of the defect's surface dimension and multilayer structure, on the intensity-signal obtained from the inspection was analyzed. Three mask blanks were inspected from which 55 defects, observed with AFM and SEM, were classified as amplitude-defects or phase-defects. The surface dimensions and SEVDs (sphere equivalent volume diameters) of the defects were measured with the AFM. In the case where their SEVDs were same as of the programmed phase-defects, they were found to produce stronger intensitysignals in comparison to the ones from the programmed phase-defects. Cross-sectional multilayer structures of two native phase-defects were observed with TEM, and those defects formed non-conformal structures in the multilayer. This result means that most of the native phase-defects tend to form a non-conformal structure, and can make large impact on the wafer image in comparison to the ones from a conformal structure. Besides phase-defects, the actinic inspection also detected amplitude-defects. Although the sensitivities of the amplitude-defects were found to be lower than those of the phase-defects, an amplitude-defect higher than 30 nm could be detected with high probability.

  9. Full conjugate analysis of normal multiple traits with missing records using a generalized inverted Wishart distribution

    Directory of Open Access Journals (Sweden)

    Birchmeier Ana

    2004-01-01

    Full Text Available Abstract A Markov chain Monte Carlo (MCMC algorithm to sample an exchangeable covariance matrix, such as the one of the error terms (R0 in a multiple trait animal model with missing records under normal-inverted Wishart priors is presented. The algorithm (FCG is based on a conjugate form of the inverted Wishart density that avoids sampling the missing error terms. Normal prior densities are assumed for the 'fixed' effects and breeding values, whereas the covariance matrices are assumed to follow inverted Wishart distributions. The inverted Wishart prior for the environmental covariance matrix is a product density of all patterns of missing data. The resulting MCMC scheme eliminates the correlation between the sampled missing residuals and the sampled R0, which in turn has the effect of decreasing the total amount of samples needed to reach convergence. The use of the FCG algorithm in a multiple trait data set with an extreme pattern of missing records produced a dramatic reduction in the size of the autocorrelations among samples for all lags from 1 to 50, and this increased the effective sample size from 2.5 to 7 times and reduced the number of samples needed to attain convergence, when compared with the 'data augmentation' algorithm.

  10. Fractal analysis of en face tomographic images obtained with full field optical coherence tomography

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Wanrong; Zhu, Yue [Department of Optical Engineering, Nanjing University of Science and Technology, Jiangsu (China)

    2017-03-15

    The quantitative modeling of the imaging signal of pathological areas and healthy areas is necessary to improve the specificity of diagnosis with tomographic en face images obtained with full field optical coherence tomography (FFOCT). In this work, we propose to use the depth-resolved change in the fractal parameter as a quantitative specific biomarker of the stages of disease. The idea is based on the fact that tissue is a random medium and only statistical parameters that characterize tissue structure are appropriate. We successfully relate the imaging signal in FFOCT to the tissue structure in terms of the scattering function and the coherent transfer function of the system. The formula is then used to analyze the ratio of the Fourier transforms of the cancerous tissue to the normal tissue. We found that when the tissue changes from the normal to cancerous the ratio of the spectrum of the index inhomogeneities takes the form of an inverse power law and the changes in the fractal parameter can be determined by estimating slopes of the spectra of the ratio plotted on a log-log scale. The fresh normal and cancer liver tissues were imaged to demonstrate the potential diagnostic value of the method at early stages when there are no significant changes in tissue microstructures. (copyright 2016 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. An analysis of cardiac defects and surgical interventions in 84 cases with full trisomy 18.

    Science.gov (United States)

    Bruns, Deborah A; Martinez, Alyssa

    2016-02-01

    Trisomy 18 (Edwards syndrome) is the second most common autosomal trisomy after trisomy 21. Medical issues commonly include cardiac defects, such as ventricular septal defect (VSD) and atrial septal defect (ASD). If untreated, these conditions can contribute to the associated infant mortality. The objective of the study was review parent-reported information on 84 cases with full trisomy 18 focusing on prenatal and postnatal assessment and confirmation of cardiac defects and on subsequent treatment with cardiac surgery and post-surgery outcomes. At birth, 65 parent responses indicated the presence of VSD (77.4%), 38 ASD (45.2%), and 50 patent ductus arteriosus (PDA) (59.5%). The presence of multiple cardiac defects was also analyzed including 25 cases with VSD, ASD, and PDA at birth. The total reduced to 18 at survey completion. Twenty-four cases had one or more cardiac defects repaired for a total of 34 corrective surgeries. Age at surgery varied from 2 weeks to 41 months of age with most performed under 1 year of age. Twenty-one cases were still living at the time of survey completion (87.5%). From these date we provide recommendations and implications.

  12. Sensitivity analysis for elastic full-waveform inversion in VTI media

    KAUST Repository

    Kamath, Nishant

    2014-08-05

    Multiparameter full-waveform inversion (FWI) is generally nonunique, and the results are strongly influenced by the geometry of the experiment and the type of recorded data. Studying the sensitivity of different subsets of data to the model parameters may help in choosing an optimal acquisition design, inversion workflow, and parameterization. Here, we derive the Fréchet kernel for FWI of multicomponent data from a 2D VTI (tranversely isotropic with a vertical symmetry axis) medium. The kernel is obtained by linearizing the elastic wave equation using the Born approximation and employing the asymptotic Green\\'s function. The amplitude of the kernel (‘radiation pattern’) yields the angle-dependent energy scattered by a perturbation in a certain model parameter. The perturbations are described in terms of the P- and S-wave vertical velocities and the P-wave normal-moveout and horizontal velocities. The background medium is assumed to be homogeneous and isotropic, which allows us to obtain simple expressions for the radiation patterns corresonding to all four velocities. These patterns help explain the FWI results for multicomponent transmission data generated for Gaussian anomalies in the Thomsen parameters inserted into a homogeneous VTI medium.

  13. Spiral implants bearing full-arch rehabilitation: analysis of clinical outcome.

    Science.gov (United States)

    Danza, Matteo; Grecchi, Francesco; Zollino, Ilaria; Casadio, Claudia; Carinci, Francesco

    2011-08-01

    A spiral implant (SPI) is a conical internal helix implant with a variable thread design which confers the characteristic of self drilling, self tapping, and self bone condensing. The effectiveness of this type of implant has been reported in several clinical situations. However, because there are no reports that specifically focus on one of the biggest challenges in oral rehabilitation, that is, full arch rehabilitation, it was decided to perform a retrospective study. The study population was composed of 23 patients (12 women and 11 men, median age 57 years) for evaluation and implant treatment between January 2005 and June 2009. Two-hundred six spiral family implants (SFIs) were inserted with a mean postloading follow-up of 23 months. Several variables were investigated: demographic (age and gender), anatomic (maxilla and mandible, tooth site), implant (type, length, and diameter), surgical (surgeon, postextractive, flapless technique, grafts), and prosthetic (implant/crown ratio, dentition in the antagonist arch, type of loading, and computerized tomography [CT] planning) variables. Implant loss and peri-implant bone resorption were evaluated. Univariate and multivariate tests were performed. Survival and success rates were 97.1% and 82.5%, respectively. Only implant length and implant/crown ratio showed statistical significance in determining a better clinical outcome. In conclusion, SFIs are a reliable tool for the most difficult cases of oral rehabilitation. No differences were detected among implant type. Length and implant/crown ratio can influence the crestal bone resorption with better result for longer fixtures and a higher implant/crown ratio. In addition, banked bone derived from living donors can be used to restore alveolar ridge augmentation without adverse effects. Finally, flapless and CT-planned surgery did not significantly increase the clinical outcome in most complex rehabilitation.

  14. Assessing breast cancer masking risk with automated texture analysis in full field digital mammography

    DEFF Research Database (Denmark)

    Kallenberg, Michiel Gijsbertus J; Lillholm, Martin; Diao, Pengfei

    2015-01-01

    status in a five-fold cross validation. To assess the interaction of the texture scores with breast density, Volpara Density Grade (VDG) was determined for each image using Volpara, Matakina Technology, New Zealand. RESULTS We grouped women into low (VDG 1/2) versus high (VDG 3/4) dense, and low...... for the high texture score group (as compared to the low texture score group) this OR was 2.19 (1.37-3.49). Women who were classified as low dense but had a high texture score had a higher masking risk (OR 1.66 (0.53-5.20)) than women with dense breasts but a low texture score. CONCLUSION Mammographic texture...... is associated with breast cancer masking risk. We were able to identify a subgroup of women who are at an increased risk of having a cancer that is not detected due to textural masking, even though their breasts are non-dense. CLINICAL RELEVANCE/APPLICATION Automatic texture analysis enables assessing the risk...

  15. Comparative full-length sequence analysis of Marek's disease virus vaccine strain 814.

    Science.gov (United States)

    Zhang, Feng; Liu, Chang-Jun; Zhang, Yan-Ping; Li, Zhi-Jie; Liu, Ai-Ling; Yan, Fu-Hai; Cong, Feng; Cheng, Yun

    2012-01-01

    The complete DNA sequence of Marek's disease virus (MDV) serotype 1 vaccine strain 814 was determined. It consisted of 172,541 bp, with an overall gene organization identical to that of the MDV-1 type strains. Comparative genomic analysis of vaccine strains (814 and CVI988) and other strains (CU-2, Md5, and Md11) showed that 814 was most similar to CVI988. Several unique insertions, deletions, and substitutions were identified in strain 814. Of note, a 177-bp insertion in the overlapping genes encoding the Meq, RLORF6, and 23-kDa proteins of strain 814 was identified, and a 69-bp deletion was also located in the origin of replication site (Ori) in the gene encoding RLORF12. Compared to the CVI988 vaccine strain, a deletion of 510 bp was identified in the UL36 gene. These analyses identified key mutations in the 814 strain and the vaccine strain that could be exploited for future MDV vaccine design.

  16. Full genome analysis of a novel type II feline coronavirus NTU156.

    Science.gov (United States)

    Lin, Chao-Nan; Chang, Ruey-Yi; Su, Bi-Ling; Chueh, Ling-Ling

    2013-04-01

    Infections by type II feline coronaviruses (FCoVs) have been shown to be significantly correlated with fatal feline infectious peritonitis (FIP). Despite nearly six decades having passed since its first emergence, different studies have shown that type II FCoV represents only a small portion of the total FCoV seropositivity in cats; hence, there is very limited knowledge of the evolution of type II FCoV. To elucidate the correlation between viral emergence and FIP, a local isolate (NTU156) that was derived from a FIP cat was analyzed along with other worldwide strains. Containing an in-frame deletion of 442 nucleotides in open reading frame 3c, the complete genome size of NTU156 (28,897 nucleotides) appears to be the smallest among the known type II feline coronaviruses. Bootscan analysis revealed that NTU156 evolved from two crossover events between type I FCoV and canine coronavirus, with recombination sites located in the RNA-dependent RNA polymerase and M genes. With an exchange of nearly one-third of the genome with other members of alphacoronaviruses, the new emerging virus could gain new antigenicity, posing a threat to cats that either have been infected with a type I virus before or never have been infected with FCoV.

  17. Full-Sky Analysis of Cosmic-Ray Anisotropy with IceCube and HAWC

    CERN Document Server

    ,

    2015-01-01

    During the past two decades, experiments in both the Northern and Southern hemispheres have observed a small but measurable energy-dependent sidereal anisotropy in the arrival direction distribution of galactic cosmic rays. The relative amplitude of the anisotropy is $10^{-4} - 10^{-3}$. However, each of these individual measurements is restricted by limited sky coverage, and so the pseudo-power spectrum of the anisotropy obtained from any one measurement displays a systematic correlation between different multipole modes $C_\\ell$. To address this issue, we present the preliminary status of a joint analysis of the anisotropy on all angular scales using cosmic-ray data from the IceCube Neutrino Observatory located at the South Pole ($90^\\circ$ S) and the High-Altitude Water Cherenkov (HAWC) Observatory located at Sierra Negra, Mexico ($19^\\circ$ N). We describe the methods used to combine the IceCube and HAWC data, address the individual detector systematics and study the region of overlapping field of view be...

  18. Generation and analysis of plasmas with centrally reduced helicity in full-tungsten ASDEX upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Bock, Alexander

    2016-03-01

    The most promising concepts for harnessing nuclear fusion are toroidal devices like tokamaks, where a plasma is confined by helically twisted magnetic field lines. To provide the twisting of the field lines, a tokamak relies on a toroidal current in the plasma, which is largely generated by a transformer. As such, conventional tokamaks are limited to pulsed operation. Moreover, this current makes tokamak plasmas prone to numerous confinement degrading magnetohydrodynamic (MHD) instabilities that can emerge at locations where the field line helicity q takes on rational values like 1/1, 3/2 or 2/1, i.e. sawteeth or neoclassical tearing modes (NTMs). This thesis presents studies of plasmas with centrally elevated q-profiles created by external electron-cyclotron and neutral beam current drive (ECCD/NBCD) under steady-state conditions in the full-tungsten tokamak ASDEX Upgrade. Without the usually monotonic q-profile, instabilities of low helicity disappear, thereby improving the plasma stability. Furthermore, elevating q increases the amount of so-called (toroidal) bootstrap current, which the plasma drives by itself in the presence of pressure gradients, thereby reducing the reliance on the transformer. In the best case, an advanced tokamak (AT) could thus run in steady state. Additionally, an elevated and thus flat/slightly reversed q-profile is thought to improve confinement by impeding turbulent transport. Reconstruction of the tailored q-profile is accomplished with the new integrated data equilibrium (IDE) code and information from a key diagnostic that is based on the Motional Stark Effect (MSE). During the course of this work it was discovered that the MSE diagnostic suffers from interference from polarised background light. A prototype mitigation system was successfully tested. Also, non-linearities in the diagnostic's optical relay system were found and a calibration scheme devised to take them into account. Both the conventional approach of AT

  19. A full economic analysis of switchgrass under different scenarios in Italy estimated by BEE model

    Energy Technology Data Exchange (ETDEWEB)

    Monti, A.; Fazio, S.; Venturi, G. [Department of Agroenvironmental Science and Technologies, Bologna (Italy); Lychnaras, V.; Soldatos, P. [Agricultural University of Athens, Athens (Greece). Laboratory of Agribusiness Management

    2007-04-15

    Three different scenarios of switchgrass (Panicum virgatum L.) cultivation (high, mild and low) in two different environmental conditions (North and South Italy) were economically analysed by the computerized model BEE. The dataset was mostly generated from an 8.6 ha field of switchgrass planted in 2002 at the University of Bologna (North Italy). Annual equivalent costs (AEC) and break-even yield (BEY, i.e. the dry matter yield at which cost equals selling price) of each scenario were calculated to assess the feasibility of each scenario. AEC ranged from EUR511 to EUR1.257 ha{sup -1} being always higher in northern than southern regions. As expected, BEY varied to an extent depending on input levels. BEY was clearly higher under intensive cropping systems (H{sub S}) compared to mild-(M{sub S}) and low-input (L{sub S}) scenarios. However, even for M{sub S} or L{sub S}, BEY generally exceeded the harvested yield. Therefore, we can conclude that, at the market price of EUR55 Mg{sup -1} (dry basis), switchgrass can be hardly grown both in North and South Italy. However, the biomass market price appeared surprisingly underestimated if compared to the unit energy price of crude oil, therefore a desirable increase of biomass price could be expected in the next few years. Sensitivity analysis showed that biomass price strongly affects BEY, and this was especially found in H{sub S}. Furthermore, the differences in BEY between L{sub S} and H{sub S} clearly decreased with increasing market prices. Therefore, H{sub S} could be better indicated than L{sub S} at high market prices. Switchgrass was found to be more profitable than some conventional crops to an extent depending on the yield higher than BEY (Y{sub i}). At the current biomass price, Y{sub i} was from less than 1 Mg ha{sup -1} (maize and alfalfa) to more than 4 Mg ha{sup -1} (sugarbeet). (author)

  20. Analysis of expressed sequence tags generated from full-length enriched cDNA libraries of melon

    Directory of Open Access Journals (Sweden)

    Bendahmane Abdelhafid

    2011-05-01

    Full Text Available Abstract Background Melon (Cucumis melo, an economically important vegetable crop, belongs to the Cucurbitaceae family which includes several other important crops such as watermelon, cucumber, and pumpkin. It has served as a model system for sex determination and vascular biology studies. However, genomic resources currently available for melon are limited. Result We constructed eleven full-length enriched and four standard cDNA libraries from fruits, flowers, leaves, roots, cotyledons, and calluses of four different melon genotypes, and generated 71,577 and 22,179 ESTs from full-length enriched and standard cDNA libraries, respectively. These ESTs, together with ~35,000 ESTs available in public domains, were assembled into 24,444 unigenes, which were extensively annotated by comparing their sequences to different protein and functional domain databases, assigning them Gene Ontology (GO terms, and mapping them onto metabolic pathways. Comparative analysis of melon unigenes and other plant genomes revealed that 75% to 85% of melon unigenes had homologs in other dicot plants, while approximately 70% had homologs in monocot plants. The analysis also identified 6,972 gene families that were conserved across dicot and monocot plants, and 181, 1,192, and 220 gene families specific to fleshy fruit-bearing plants, the Cucurbitaceae family, and melon, respectively. Digital expression analysis identified a total of 175 tissue-specific genes, which provides a valuable gene sequence resource for future genomics and functional studies. Furthermore, we identified 4,068 simple sequence repeats (SSRs and 3,073 single nucleotide polymorphisms (SNPs in the melon EST collection. Finally, we obtained a total of 1,382 melon full-length transcripts through the analysis of full-length enriched cDNA clones that were sequenced from both ends. Analysis of these full-length transcripts indicated that sizes of melon 5' and 3' UTRs were similar to those of tomato, but

  1. Counting and differentiating aquatic biotic nanoparticles by full-field interferometry: from laboratory tests to Tara Oceans sample analysis

    CERN Document Server

    Boccara, Martine; Bryan, Catherine Venien; Bailly-Bechet, Marc; Bowler, Chris; Boccara, Albert Claude

    2016-01-01

    There is a huge abundance of viruses and membrane vesicles in seawater. We describe a new full-field, incoherently illuminated, shot-noise limited, common-path interferometric detection method that we couple with the analysis of Brownian motion to detect, quantify, and differentiate biotic nanoparticles. We validated the method with calibrated nanoparticles and homogeneous DNA or RNA.viruses. The smallest virus size that we characterized with a suitable signal-to-noise ratio was around 30 nm in diameter. Analysis of Brownian motions revealed anisotropic trajectories for myoviruses.We further applied the method for vesicles detection and for analysis of coastal and oligotrophic samples from Tara Oceans circumnavigation.

  2. The acropetal effects of indole-3-acetic acid in isolated shoot segments of Acer pseudoplatanus L. II. Possible regulation by a vectorial fieid of auxin waves

    Directory of Open Access Journals (Sweden)

    Jacek A. Adamczyk

    2014-02-01

    Full Text Available The acropetal effects of auxin on elongation of axillary buds and on modulation of the wave-like pattern of basipetal efflux of natural auxin to agar from Acer pseudoplatanus L. shoots were studied. When synthetic IAA was applied to cut surfaces of one of two branches the elongation growth of buds situated on the opposite branch was retarded, suggesting regulation independent of the direct action of the molecules of the applied IAA. Oscillations in basipetal transport of natural auxin along the stem segments were observed corroborating the results of other authors using different tree species. Apical application of synthetic IAA for 1 hour to the lateral branch caused a phase shift of the wave-like pattern of basipetal efflux of natural auxin, when the stem segment above the treated branch was sectioned. The same effect was observed evoked by the laterally growing branch which is interpreted as an effect of natural auxin produced by the actively growing shoot. These modulations could be propagated acropetally at a rate excluding direct action of auxin molecules at the sites of measurement. The results seem to corroborate the hypothesis suggesting that auxin is involved in acropetal regulation of shoot apex growth through its effect upon modulation of the vectorial field which arises when the auxin-waves translocate in cambium.

  3. A pointwise constrained version of the Liapunov convexity theorem for vectorial linear first-order control systems

    Science.gov (United States)

    Carlota, Clara; Chá, Sílvia; Ornelas, António

    2016-07-01

    We generalize the Liapunov convexity theorem's version for vectorial control systems driven by linear ODEs of first-order p = 1, in any dimension d ∈ N, by including a pointwise state-constraint. More precisely, given a x ‾ (ṡ) ∈W p , 1 ([ a , b ] ,Rd) solving the convexified p-th order differential inclusion Lp x ‾ (t) ∈ co {u0 (t) ,u1 (t) , … ,um (t) } a.e., consider the general problem consisting in finding bang-bang solutions (i.e. Lp x ˆ (t) ∈ {u0 (t) ,u1 (t) , … ,um (t) } a.e.) under the same boundary-data, x ˆ (k) (a) =x ‾ (k) (a) &x ˆ (k) (b) =x ‾ (k) (b) (k = 0 , 1 , … , p - 1); but restricted, moreover, by a pointwise state constraint of the type ≤ ∀ t ∈ [ a , b ] (e.g. ω = (1 , 0 , … , 0) yielding xˆ1 (t) ≤x‾1 (t)). Previous results in the scalar d = 1 case were the pioneering Amar & Cellina paper (dealing with Lp x (ṡ) =x‧ (ṡ)), followed by Cerf & Mariconda results, who solved the general case of linear differential operators Lp of order p ≥ 2 with C0 ([ a , b ]) -coefficients. This paper is dedicated to: focus on the missing case p = 1, i.e. using Lp x (ṡ) =x‧ (ṡ) + A (ṡ) x (ṡ) ; generalize the dimension of x (ṡ) , from the scalar case d = 1 to the vectorial d ∈ N case; weaken the coefficients, from continuous to integrable, so that A (ṡ) now becomes a d × d-integrable matrix; and allow the directional vector ω to become a moving AC function ω (ṡ) . Previous vectorial results had constant ω, no matrix (i.e. A (ṡ) ≡ 0) and considered: constant control-vertices (Amar & Mariconda) and, more recently, integrable control-vertices (ourselves).

  4. Vectorial analysis of polarization issues in multi-axial nulling interferometers for exoplanet detection

    NARCIS (Netherlands)

    Spronck, J.; Pereira, S.F.; Braat, J.J.M.

    2007-01-01

    We show the theoretical limitations of a multi-axial nulling interferometer with respect to longitudinal polarization. We furthermore analyze the filtering capabilities of a single-mode fiber in this case.

  5. Full-genome analysis of avian influenza A(H5N1) virus from a human, North America, 2013.

    Science.gov (United States)

    Pabbaraju, Kanti; Tellier, Raymond; Wong, Sallene; Li, Yan; Bastien, Nathalie; Tang, Julian W; Drews, Steven J; Jang, Yunho; Davis, C Todd; Fonseca, Kevin; Tipples, Graham A

    2014-05-01

    Full-genome analysis was conducted on the first isolate of a highly pathogenic avian influenza A(H5N1) virus from a human in North America. The virus has a hemagglutinin gene of clade 2.3.2.1c and is a reassortant with an H9N2 subtype lineage polymerase basic 2 gene. No mutations conferring resistance to adamantanes or neuraminidase inhibitors were found.

  6. DSP and FPGA based system to control a wind turbine generator implementing a variable speed vectorial control method

    OpenAIRE

    Perales Esteve, Manuel Ángel; Barrero, Federico; Mora Jiménez, José Luis; Galván Díez, Eduardo; Carrasco Solís, Juan Manuel; García Franquelo, Leopoldo

    1997-01-01

    The purpose of this paper is to describe a DSP and FPGA control system to implement a variable speed vectorial control. Two semi-systems, both of them consisting on a DSP, a FPGA and A/D, D/A & digital I/O’s are used. Each one will control an inverter: The first inverter implements a variable speed vector control of the induction generator and the second one handle the power injected into the utility grid. Experimental results will be shown to confirm the validity of the proposed controller.

  7. Cálculo vectorial discreto para problemas elípticos sobre retículas uniformes

    OpenAIRE

    Santos Gutiérrez, Roberto

    2004-01-01

    Esta tesina se enmarca dentro de los trabajos en el campo del análisis numérico denominados genéricamente como "discretizaciones miméticas de la mecánica del medio continuo". La idea consiste en establecer un cálculo vectorial sobre retículas uniformes siguiendo el modelo del caso continuo, de forma que se plantean los problemas elípticos directamente en medios discretos. Esto conduce a obtener operadores discretos análogos al gradiente, divergencia y laplaciano, y se demuestra que estos oper...

  8. Hybrid System Modeling and Full Cycle Operation Analysis of a Two-Stroke Free-Piston Linear Generator

    Directory of Open Access Journals (Sweden)

    Peng Sun

    2017-02-01

    Full Text Available Free-piston linear generators (FPLGs have attractive application prospects for hybrid electric vehicles (HEVs owing to their high-efficiency, low-emissions and multi-fuel flexibility. In order to achieve long-term stable operation, the hybrid system design and full-cycle operation strategy are essential factors that should be considered. A 25 kW FPLG consisting of an internal combustion engine (ICE, a linear electric machine (LEM and a gas spring (GS is designed. To improve the power density and generating efficiency, the LEM is assembled with two modular flat-type double-sided PM LEM units, which sandwich a common moving-magnet plate supported by a middle keel beam and bilateral slide guide rails to enhance the stiffness of the moving plate. For the convenience of operation processes analysis, the coupling hybrid system is modeled mathematically and a full cycle simulation model is established. Top-level systemic control strategies including the starting, stable operating, fault recovering and stopping strategies are analyzed and discussed. The analysis results validate that the system can run stably and robustly with the proposed full cycle operation strategy. The effective electric output power can reach 26.36 kW with an overall system efficiency of 36.32%.

  9. Correlation of finite-element structural dynamic analysis with measured free vibration characteristics for a full-scale helicopter fuselage

    Science.gov (United States)

    Kenigsberg, I. J.; Dean, M. W.; Malatino, R.

    1974-01-01

    The correlation achieved with each program provides the material for a discussion of modeling techniques developed for general application to finite-element dynamic analyses of helicopter airframes. Included are the selection of static and dynamic degrees of freedom, cockpit structural modeling, and the extent of flexible-frame modeling in the transmission support region and in the vicinity of large cut-outs. The sensitivity of predicted results to these modeling assumptions are discussed. Both the Sikorsky Finite-Element Airframe Vibration analysis Program (FRAN/Vibration Analysis) and the NASA Structural Analysis Program (NASTRAN) have been correlated with data taken in full-scale vibration tests of a modified CH-53A helicopter.

  10. Full Navier-Stokes analysis of a two-dimensional mixer/ejector nozzle for noise suppression

    Science.gov (United States)

    Debonis, James R.

    1992-01-01

    A three-dimensional full Navier-Stokes (FNS) analysis was performed on a mixer/ejector nozzle designed to reduce the jet noise created at takeoff by a future supersonic transport. The PARC3D computational fluid dynamics (CFD) code was used to study the flow field of the nozzle. The grid that was used in the analysis consisted of approximately 900,000 node points contained in eight grid blocks. Two nozzle configurations were studied: a constant area mixing section and a diverging mixing section. Data are presented for predictions of pressure, velocity, and total temperature distributions and for evaluations of internal performance and mixing effectiveness. The analysis provided good insight into the behavior of the flow.

  11. fullfact: an R package for the analysis of genetic and maternal variance components from full factorial mating designs.

    Science.gov (United States)

    Houde, Aimee Lee S; Pitcher, Trevor E

    2016-03-01

    Full factorial breeding designs are useful for quantifying the amount of additive genetic, nonadditive genetic, and maternal variance that explain phenotypic traits. Such variance estimates are important for examining evolutionary potential. Traditionally, full factorial mating designs have been analyzed using a two-way analysis of variance, which may produce negative variance values and is not suited for unbalanced designs. Mixed-effects models do not produce negative variance values and are suited for unbalanced designs. However, extracting the variance components, calculating significance values, and estimating confidence intervals and/or power values for the components are not straightforward using traditional analytic methods. We introduce fullfact - an R package that addresses these issues and facilitates the analysis of full factorial mating designs with mixed-effects models. Here, we summarize the functions of the fullfact package. The observed data functions extract the variance explained by random and fixed effects and provide their significance. We then calculate the additive genetic, nonadditive genetic, and maternal variance components explaining the phenotype. In particular, we integrate nonnormal error structures for estimating these components for nonnormal data types. The resampled data functions are used to produce bootstrap-t confidence intervals, which can then be plotted using a simple function. We explore the fullfact package through a worked example. This package will facilitate the analyses of full factorial mating designs in R, especially for the analysis of binary, proportion, and/or count data types and for the ability to incorporate additional random and fixed effects and power analyses.

  12. A full-spectrum analysis of high-speed train interior noise under multi-physical-field coupling excitations

    Science.gov (United States)

    Zheng, Xu; Hao, Zhiyong; Wang, Xu; Mao, Jie

    2016-06-01

    High-speed-railway-train interior noise at low, medium, and high frequencies could be simulated by finite element analysis (FEA) or boundary element analysis (BEA), hybrid finite element analysis-statistical energy analysis (FEA-SEA) and statistical energy analysis (SEA), respectively. First, a new method named statistical acoustic energy flow (SAEF) is proposed, which can be applied to the full-spectrum HST interior noise simulation (including low, medium, and high frequencies) with only one model. In an SAEF model, the corresponding multi-physical-field coupling excitations are firstly fully considered and coupled to excite the interior noise. The interior noise attenuated by sound insulation panels of carriage is simulated through modeling the inflow acoustic energy from the exterior excitations into the interior acoustic cavities. Rigid multi-body dynamics, fast multi-pole BEA, and large-eddy simulation with indirect boundary element analysis are first employed to extract the multi-physical-field excitations, which include the wheel-rail interaction forces/secondary suspension forces, the wheel-rail rolling noise, and aerodynamic noise, respectively. All the peak values and their frequency bands of the simulated acoustic excitations are validated with those from the noise source identification test. Besides, the measured equipment noise inside equipment compartment is used as one of the excitation sources which contribute to the interior noise. Second, a full-trimmed FE carriage model is firstly constructed, and the simulated modal shapes and frequencies agree well with the measured ones, which has validated the global FE carriage model as well as the local FE models of the aluminum alloy-trim composite panel. Thus, the sound transmission loss model of any composite panel has indirectly been validated. Finally, the SAEF model of the carriage is constructed based on the accurate FE model and stimulated by the multi-physical-field excitations. The results show

  13. Analysis of Effects of 2003 and Full-Allocation Withdrawals in Critical Area 1, East-Central New Jersey

    Science.gov (United States)

    Spitz, Frederick J.

    2009-01-01

    Critical Area 1 in east-central New Jersey was mandated in the early 1980s to address large drawdowns caused by increases in groundwater withdrawals. The aquifers involved include the Englishtown aquifer system, Wenonah-Mount Laurel aquifer, and the Upper and Middle Potomac-Raritan-Magothy aquifers. Groundwater levels recovered as a result of mandated cutbacks in withdrawals that began in the late 1980s. Subsequent increased demand for water has necessitated an analysis to determine the effects of full-allocation withdrawals, which supplements an optimization analysis done previously. A steady-state regional groundwater flow model is used to evaluate the effects of 2003 withdrawals and full-allocation withdrawals (7.3 million gallons per day greater than for 2003) on simulated water-levels. Simulation results indicate that the range of available withdrawals greater than full-allocation withdrawals is likely between 0 and 12 million gallons per day. The estimated range of available withdrawals is based on: (1) an examination of hydraulic-heads resulting from each of the two simulations, (2) an examination of differences in heads between these two simulations, (3) a comparison of simulated heads from each of the two simulations with the estimated location of salty groundwater, and (4) a comparison of simulated 2003 water levels to observed 2003 water levels. The results of the simulations also indicate that obtaining most of the available water would require varying the distribution of withdrawals and (or) relaxing the mandated hydrologic constraints used to protect the water supply.

  14. Full length cDNA cloning and expression analysis of annexinA2 gene from deer antler tissue

    Institute of Scientific and Technical Information of China (English)

    Li Hao; Xianghong Xiao; Heping Li

    2014-01-01

    ANXA2(AnnexinA2), a calcium-dependent phospholipid bind-ing protein, is involved in various Ca2+-related biological activities. In the present study, full-length cDNA of ANXA2 was isolated from the velvet antler tip tissue of sika deer (Cervus nippon hortulorum);the amino acid sequence and gene expression was analyzed by using bioinformatics and real-time reverse transcriptase polymerase chain reaction (RT-PCR) techniques. Nucleotide sequence analysis reveals that the full-length cDNA of the ANXA2 gene was 1372 bp, of which 1020 bp was in the open-reading frame (ORF) encoding 339 amino acids; its relative mo-lecular weight was 38.3 kDa; and isoelectric point was 6.72. Sequence analysis indicates that the protein includes four conserved tan-dem-duplication ANX domains. The gene-accession nucleotide sequence number in GenBank is JX315571. Expression analysis by RT-PCR re-veals that ANXA2 gene expression has a significant positive correlation with the antler-tissue mineralization process, indicating that this gene may play an important role in the regulation of antler-tissue mineraliza-tion.

  15. Vectorial magnetometry using magnetooptic Kerr effect including first- and second-order contributions for thin ferromagnetic films

    Energy Technology Data Exchange (ETDEWEB)

    Kuschel, T; Wilkens, H; Schubert, R; Wollschlaeger, J [Fachbereich Physik, Universitaet Osnabrueck, Barbarastrasse 7, D-49069 Osnabrueck (Germany); Bardenhagen, H [Physikalisches Institut, Universitaet Wuerzburg, Am Hubland, D-97074 Wuerzburg (Germany); Hamrle, J; Pistora, J, E-mail: joachim.wollschlaeger@uos.de [Department of Physics and Nanotechnology Centre, VSB - Technical University of Ostrava, 17. listopadu 15, 70833 Ostrava-Poruba (Czech Republic)

    2011-07-06

    A new combination of different vectorial magnetometry techniques using magnetooptic Kerr effect is described. The processing of the experimental data contains the separation of linear and quadratic parts of the magnetization curves and determination of all three components of the magnetization vector in units of Kerr rotation without any normalization to the saturation values. The experimental procedure includes measurements with parallel and perpendicular polarized incident light and an external magnetic field parallel and perpendicular to the plane of incidence of light. The determination of the complex Kerr amplitude and the theoretic description of the data processing in assumption of small angles of incidence and also for larger angles of incidence using adequate scaling to the mean saturation value validate this vectorial magnetometry method. In the case of an absent out-of-plane component of the magnetization vector, the complete reversal process can easily be reconstructed and interpreted by monodomain states and domain splitting. The measurement procedure and the processing of the data are demonstrated for an ultra-thin epitaxial Fe film on MgO(0 0 1).

  16. Molecular evolutionary analysis of ABCB5: the ancestral gene is a full transporter with potentially deleterious single nucleotide polymorphisms.

    Directory of Open Access Journals (Sweden)

    Karobi Moitra

    Full Text Available BACKGROUND: ABCB5 is a member of the ABC protein superfamily, which includes the transporters ABCB1, ABCC1 and ABCG2 responsible for causing drug resistance in cancer patients and also several other transporters that have been linked to human disease. The ABCB5 full transporter (ABCB5.ts is expressed in human testis and its functional significance is presently unknown. Another variant of this transporter, ABCB5 beta possess a "half-transporter-like" structure and is expressed in melanoma stem cells, normal melanocytes, and other types of pigment cells. ABCB5 beta has important clinical implications, as it may be involved with multidrug resistance in melanoma stem cells, allowing these stem cells to survive chemotherapeutic regimes. METHODOLOGY/PRINCIPAL FINDINGS: We constructed and examined in detail topological structures of the human ABCB5 protein and determined in-silico the cSNPs (coding single nucleotide polymorphisms that may affect its function. Evolutionary analysis of ABCB5 indicated that ABCB5, ABCB1, ABCB4, and ABCB11 share a common ancestor, which began duplicating early in the evolutionary history of chordates. This suggests that ABCB5 has evolved as a full transporter throughout its evolutionary history. CONCLUSIONS/SIGNIFICANCE: From our in-silco analysis of cSNPs we found that a large number of non-synonymous cSNPs map to important functional regions of the protein suggesting that these SNPs if present in human populations may play a role in diseases associated with ABCB5. From phylogenetic analyses, we have shown that ABCB5 evolved as a full transporter throughout its evolutionary history with an absence of any major shifts in selection between the various lineages suggesting that the function of ABCB5 has been maintained during mammalian evolution. This finding would suggest that ABCB5 beta may have evolved to play a specific role in human pigment cells and/or melanoma cells where it is predominantly expressed.

  17. Single-Phase Full-Wave Rectifier as an Effective Example to Teach Normalization, Conduction Modes, and Circuit Analysis Methods

    Directory of Open Access Journals (Sweden)

    Predrag Pejovic

    2013-12-01

    Full Text Available Application of a single phase rectifier as an example in teaching circuit modeling, normalization, operating modes of nonlinear circuits, and circuit analysis methods is proposed.The rectifier supplied from a voltage source by an inductive impedance is analyzed in the discontinuous as well as in the continuous conduction mode. Completely analytical solution for the continuous conduction mode is derived. Appropriate numerical methods are proposed to obtain the circuit waveforms in both of the operating modes, and to compute the performance parameters. Source code of the program that performs such computation is provided.

  18. Collection and Comparative Analysis of 1888 Full-length cDNAs from Wild Rice Oryza rufipogon Griff. W1943

    OpenAIRE

    Lu, Tingting; Yu, Shuliang; Fan, Danlin; Mu, Jie; Shangguan, Yingying; Wang, Zixuan; Minobe, Yuzo; Lin, Zhixin; Han, Bin

    2008-01-01

    A huge amount of cDNA and EST resources have been developed for cultivated rice species Oryza sativa; however, only few cDNA resources are available for wild rice species. In this study, we isolated and completely sequenced 1888 putative full-length cDNA (FLcDNA) clones from wild rice Oryza rufipogon Griff. W1943 for comparative analysis between wild and cultivated rice species. Two cDNA libraries were constructed from 3-week-old leaf samples under either normal or cold-treated conditions. Ho...

  19. In situ γ-ray spectrometry in the marine environment using full spectrum analysis for natural radionuclides.

    Science.gov (United States)

    Androulakaki, E G; Kokkoris, M; Tsabaris, C; Eleftheriou, G; Patiris, D L; Pappa, F K; Vlastou, R

    2016-08-01

    The Full Spectrum Analysis approach was applied to obtain activity concentration estimations for in situ measurements in the marine environment. The 'standard spectra' were reproduced using the MCNP-CP code. In order to extract the activity concentrations, χ(2) minimization calculations were performed by implementing the MINUIT code. The method was applied to estimate the activity concentrations for measurements in the marine environment in three different test cases. The estimated activity concentrations were in good agreement with the experimentally derived ones within uncertainties.

  20. Common-mode noise analysis, modeling and filter design for a phase-shifted full-bridge forward converter

    DEFF Research Database (Denmark)

    Makda, Ishtiyaq Ahmed; Nymand, Morten

    2015-01-01

    This paper presents the common-mode noise analysis and modeling of a phase-shifted full-bridge forward converter. The common-mode noise source due to a transformer inter-winding capacitance is considered for the case of study. The generated common-mode noise voltage-source in a converter...... is analytically determined, which then leads to a common-mode noise modeling of a phase-shifted converter. Using a proposed model, common-mode noise-current harmonics are calculated and a fully analytical filter design procedure is presented to comply with the CISPR-11 standard. Finally, a prototype phase......-shifted forward converter is built to verify the theoretical analysis. This study shows that the primary-to-secondary transformer winding capacitance creates a very significant amount of common-mode noise current in a phase-shifted forward converter....

  1. Proximal gamma-ray spectroscopy to predict soil properties using windows and full-spectrum analysis methods.

    Science.gov (United States)

    Mahmood, Hafiz Sultan; Hoogmoed, Willem B; van Henten, Eldert J

    2013-11-27

    Fine-scale spatial information on soil properties is needed to successfully implement precision agriculture. Proximal gamma-ray spectroscopy has recently emerged as a promising tool to collect fine-scale soil information. The objective of this study was to evaluate a proximal gamma-ray spectrometer to predict several soil properties using energy-windows and full-spectrum analysis methods in two differently managed sandy loam fields: conventional and organic. In the conventional field, both methods predicted clay, pH and total nitrogen with a good accuracy (R2 ≥ 0.56) in the top 0-15 cm soil depth, whereas in the organic field, only clay content was predicted with such accuracy. The highest prediction accuracy was found for total nitrogen (R2 = 0.75) in the conventional field in the energy-windows method. Predictions were better in the top 0-15 cm soil depths than in the 15-30 cm soil depths for individual and combined fields. This implies that gamma-ray spectroscopy can generally benefit soil characterisation for annual crops where the condition of the seedbed is important. Small differences in soil structure (conventional vs. organic) cannot be determined. As for the methodology, we conclude that the energy-windows method can establish relations between radionuclide data and soil properties as accurate as the full-spectrum analysis method.

  2. ASKI: A modular toolbox for scattering-integral-based seismic full waveform inversion and sensitivity analysis utilizing external forward codes

    Science.gov (United States)

    Schumacher, Florian; Friederich, Wolfgang

    Due to increasing computational resources, the development of new numerically demanding methods and software for imaging Earth's interior remains of high interest in Earth sciences. Here, we give a description from a user's and programmer's perspective of the highly modular, flexible and extendable software package ASKI-Analysis of Sensitivity and Kernel Inversion-recently developed for iterative scattering-integral-based seismic full waveform inversion. In ASKI, the three fundamental steps of solving the seismic forward problem, computing waveform sensitivity kernels and deriving a model update are solved by independent software programs that interact via file output/input only. Furthermore, the spatial discretizations of the model space used for solving the seismic forward problem and for deriving model updates, respectively, are kept completely independent. For this reason, ASKI does not contain a specific forward solver but instead provides a general interface to established community wave propagation codes. Moreover, the third fundamental step of deriving a model update can be repeated at relatively low costs applying different kinds of model regularization or re-selecting/weighting the inverted dataset without need to re-solve the forward problem or re-compute the kernels. Additionally, ASKI offers the user sensitivity and resolution analysis tools based on the full sensitivity matrix and allows to compose customized workflows in a consistent computational environment. ASKI is written in modern Fortran and Python, it is well documented and freely available under terms of the GNU General Public License (http://www.rub.de/aski).

  3. Retinal Arteriolar Morphometry Based on Full Width at Half Maximum Analysis of Spectral-Domain Optical Coherence Tomography Images.

    Directory of Open Access Journals (Sweden)

    Yu Hua Tong

    Full Text Available In this study, we develop a microdensitometry method using full width at half maximum (FWHM analysis of the retinal vascular structure in a spectral-domain optical coherence tomography (SD-OCT image and present the application of this method in the morphometry of arteriolar changes during hypertension.Two raters using manual and FWHM methods measured retinal vessel outer and lumen diameters in SD-OCT images. Inter-rater reproducibility was measured using coefficients of variation (CV, intraclass correlation coefficient and a Bland-Altman plot. OCT images from forty-three eyes of 43 hypertensive patients and 40 eyes of 40 controls were analyzed using an FWHM approach; wall thickness, wall cross-sectional area (WCSA and wall to lumen ratio (WLR were subsequently calculated.Mean difference in inter-rater agreement ranged from -2.713 to 2.658 μm when using a manual method, and ranged from -0.008 to 0.131 μm when using a FWHM approach. The inter-rater CVs were significantly less for the FWHM approach versus the manual method (P < 0.05. Compared with controls, the wall thickness, WCSA and WLR of retinal arterioles were increased in the hypertensive patients, particular in diabetic hypertensive patients.The microdensitometry method using a FWHM algorithm markedly improved inter-rater reproducibility of arteriolar morphometric analysis, and SD-OCT may represent a promising noninvasive method for in vivo arteriolar morphometry.

  4. RT-PCR and sequence analysis of the full-length fusion protein of Canine Distemper Virus from domestic dogs.

    Science.gov (United States)

    Romanutti, Carina; Gallo Calderón, Marina; Keller, Leticia; Mattion, Nora; La Torre, José

    2016-02-01

    During 2007-2014, 84 out of 236 (35.6%) samples from domestic dogs submitted to our laboratory for diagnostic purposes were positive for Canine Distemper Virus (CDV), as analyzed by RT-PCR amplification of a fragment of the nucleoprotein gene. Fifty-nine of them (70.2%) were from dogs that had been vaccinated against CDV. The full-length gene encoding the Fusion (F) protein of fifteen isolates was sequenced and compared with that of those of other CDVs, including wild-type and vaccine strains. Phylogenetic analysis using the F gene full-length sequences grouped all the Argentinean CDV strains in the SA2 clade. Sequence identity with the Onderstepoort vaccine strain was 89.0-90.6%, and the highest divergence was found in the 135 amino acids corresponding to the F protein signal-peptide, Fsp (64.4-66.7% identity). In contrast, this region was highly conserved among the local strains (94.1-100% identity). One extra putative N-glycosylation site was identified in the F gene of CDV Argentinean strains with respect to the vaccine strain. The present report is the first to analyze full-length F protein sequences of CDV strains circulating in Argentina, and contributes to the knowledge of molecular epidemiology of CDV, which may help in understanding future disease outbreaks.

  5. A comparative analysis of HIV drug resistance interpretation based on short reverse transcriptase sequences versus full sequences

    Directory of Open Access Journals (Sweden)

    Stevens Wendy

    2010-10-01

    Full Text Available Abstract Background As second-line antiretroviral treatment (ART becomes more accessible in resource-limited settings (RLS, the need for more affordable monitoring tools such as point-of-care viral load assays and simplified genotypic HIV drug resistance (HIVDR tests increases substantially. The prohibitive expenses of genotypic HIVDR assays could partly be addressed by focusing on a smaller region of the HIV reverse transcriptase gene (RT that encompasses the majority of HIVDR mutations for people on ART in RLS. In this study, an in silico analysis of 125,329 RT sequences was performed to investigate the effect of submitting short RT sequences (codon 41 to 238 to the commonly used virco®TYPE and Stanford genotype interpretation tools. Results Pair-wise comparisons between full-length and short RT sequences were performed. Additionally, a non-inferiority approach with a concordance limit of 95% and two-sided 95% confidence intervals was used to demonstrate concordance between HIVDR calls based on full-length and short RT sequences. The results of this analysis showed that HIVDR interpretations based on full-length versus short RT sequences, using the Stanford algorithms, had concordance significantly above 95%. When using the virco®TYPE algorithm, similar concordance was demonstrated (>95%, but some differences were observed for d4T, AZT and TDF, where predictions were affected in more than 5% of the sequences. Most differences in interpretation, however, were due to shifts from fully susceptible to reduced susceptibility (d4T or from reduced response to minimal response (AZT, TDF or vice versa, as compared to the predicted full RT sequence. The virco®TYPE prediction uses many more mutations outside the RT 41-238 amino acid domain, which significantly contribute to the HIVDR prediction for these 3 antiretroviral agents. Conclusions This study illustrates the acceptability of using a shortened RT sequences (codon 41-238 to obtain reliable

  6. Full-field modal analysis during base motion excitation using high-speed 3D digital image correlation

    Science.gov (United States)

    Molina-Viedma, Ángel J.; López-Alba, Elías; Felipe-Sesé, Luis; Díaz, Francisco A.

    2017-10-01

    In recent years, many efforts have been made to exploit full-field measurement optical techniques for modal identification. Three-dimensional digital image correlation using high-speed cameras has been extensively employed for this purpose. Modal identification algorithms are applied to process the frequency response functions (FRF), which relate the displacement response of the structure to the excitation force. However, one of the most common tests for modal analysis involves the base motion excitation of a structural element instead of force excitation. In this case, the relationship between response and excitation is typically based on displacements, which are known as transmissibility functions. In this study, a methodology for experimental modal analysis using high-speed 3D digital image correlation and base motion excitation tests is proposed. In particular, a cantilever beam was excited from its base with a random signal, using a clamped edge join. Full-field transmissibility functions were obtained through the beam and converted into FRF for proper identification, considering a single degree-of-freedom theoretical conversion. Subsequently, modal identification was performed using a circle-fit approach. The proposed methodology facilitates the management of the typically large amounts of data points involved in the DIC measurement during modal identification. Moreover, it was possible to determine the natural frequencies, damping ratios and full-field mode shapes without requiring any additional tests. Finally, the results were experimentally validated by comparing them with those obtained by employing traditional accelerometers, analytical models and finite element method analyses. The comparison was performed by using the quantitative indicator modal assurance criterion. The results showed a high level of correspondence, consolidating the proposed experimental methodology.

  7. ASKI: A modular toolbox for scattering-integral-based seismic full waveform inversion and sensitivity analysis utilizing external forward codes

    Directory of Open Access Journals (Sweden)

    Florian Schumacher

    2016-01-01

    Full Text Available Due to increasing computational resources, the development of new numerically demanding methods and software for imaging Earth’s interior remains of high interest in Earth sciences. Here, we give a description from a user’s and programmer’s perspective of the highly modular, flexible and extendable software package ASKI–Analysis of Sensitivity and Kernel Inversion–recently developed for iterative scattering-integral-based seismic full waveform inversion. In ASKI, the three fundamental steps of solving the seismic forward problem, computing waveform sensitivity kernels and deriving a model update are solved by independent software programs that interact via file output/input only. Furthermore, the spatial discretizations of the model space used for solving the seismic forward problem and for deriving model updates, respectively, are kept completely independent. For this reason, ASKI does not contain a specific forward solver but instead provides a general interface to established community wave propagation codes. Moreover, the third fundamental step of deriving a model update can be repeated at relatively low costs applying different kinds of model regularization or re-selecting/weighting the inverted dataset without need to re-solve the forward problem or re-compute the kernels. Additionally, ASKI offers the user sensitivity and resolution analysis tools based on the full sensitivity matrix and allows to compose customized workflows in a consistent computational environment. ASKI is written in modern Fortran and Python, it is well documented and freely available under terms of the GNU General Public License (http://www.rub.de/aski.

  8. Profile structures of the voltage-sensor domain and the voltage-gated K+-channel vectorially oriented in a single phospholipid bilayer membrane at the solid-vapor and solid-liquid interfaces determined by x-ray interferometry

    Science.gov (United States)

    Gupta, S.; Liu, J.; Strzalka, J.; Blasie, J. K.

    2011-09-01

    One subunit of the prokaryotic voltage-gated potassium ion channel from Aeropyrum pernix (KvAP) is comprised of six transmembrane α helices, of which S1-S4 form the voltage-sensor domain (VSD) and S5 and S6 contribute to the pore domain (PD) of the functional homotetramer. However, the mechanism of electromechanical coupling interconverting the closed-to-open (i.e., nonconducting-to-K+-conducting) states remains undetermined. Here, we have vectorially oriented the detergent (OG)-solubilized VSD in single monolayers by two independent approaches, namely “directed-assembly” and “self-assembly,” to achieve a high in-plane density. Both utilize Ni coordination chemistry to tether the protein to an alkylated inorganic surface via its C-terminal His6 tag. Subsequently, the detergent is replaced by phospholipid (POPC) via exchange, intended to reconstitute a phospholipid bilayer environment for the protein. X-ray interferometry, in which interference with a multilayer reference structure is used to both enhance and phase the specular x-ray reflectivity from the tethered single membrane, was used to determine directly the electron density profile structures of the VSD protein solvated by detergent versus phospholipid, and with either a moist He (moderate hydration) or bulk aqueous buffer (high hydration) environment to preserve a native structure conformation. Difference electron density profiles, with respect to the multilayer substrate itself, for the VSD-OG monolayer and VSD-POPC membranes at both the solid-vapor and solid-liquid interfaces, reveal the profile structures of the VSD protein dominating these profiles and further indicate a successful reconstitution of a lipid bilayer environment. The self-assembly approach was similarly extended to the intact full-length KvAP channel for comparison. The spatial extent and asymmetry in the profile structures of both proteins confirm their unidirectional vectorial orientation within the reconstituted membrane and

  9. Monitoring of Wind Turbine Gearbox Condition through Oil and Wear Debris Analysis: A Full-Scale Testing Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Sheng, Shuangwen

    2016-10-01

    Despite the wind industry's dramatic development during the past decade, it is still challenged by premature turbine subsystem/component failures, especially for turbines rated above 1 MW. Because a crane is needed for each replacement, gearboxes have been a focal point for improvement in reliability and availability. Condition monitoring (CM) is a technique that can help improve these factors, leading to reduced turbine operation and maintenance costs and, subsequently, lower cost of energy for wind power. Although technical benefits of CM for the wind industry are normally recognized, there is a lack of published information on the advantages and limitations of each CM technique confirmed by objective data from full-scale tests. This article presents first-hand oil and wear debris analysis results obtained through tests that were based on full-scale wind turbine gearboxes rated at 750 kW. The tests were conducted at the 2.5-MW dynamometer test facility at the National Wind Technology Center at the National Renewable Energy Laboratory. The gearboxes were tested in three conditions: run-in, healthy, and damaged. The investigated CM techniques include real-time oil condition and wear debris monitoring, both inline and online sensors, and offline oil sample and wear debris analysis, both onsite and offsite laboratories. The reported results and observations help increase wind industry awareness of the benefits and limitations of oil and debris analysis technologies and highlight the challenges in these technologies and other tribological fields for the Society of Tribologists and Lubrication Engineers and other organizations to help address, leading to extended gearbox service life.

  10. An analysis of expressed sequence tags of developing castor endosperm using a full-length cDNA library

    Directory of Open Access Journals (Sweden)

    Wallis James G

    2007-07-01

    Full Text Available Abstract Background Castor seeds are a major source for ricinoleate, an important industrial raw material. Genomics studies of castor plant will provide critical information for understanding seed metabolism, for effectively engineering ricinoleate production in transgenic oilseeds, or for genetically improving castor plants by eliminating toxic and allergic proteins in seeds. Results Full-length cDNAs are useful resources in annotating genes and in providing functional analysis of genes and their products. We constructed a full-length cDNA library from developing castor endosperm, and obtained 4,720 ESTs from 5'-ends of the cDNA clones representing 1,908 unique sequences. The most abundant transcripts are genes encoding storage proteins, ricin, agglutinin and oleosins. Several other sequences are also very numerous, including two acidic triacylglycerol lipases, and the oleate hydroxylase (FAH12 gene that is responsible for ricinoleate biosynthesis. The role(s of the lipases in developing castor seeds are not clear, and co-expressing of a lipase and the FAH12 did not result in significant changes in hydroxy fatty acid accumulation in transgenic Arabidopsis seeds. Only one oleate desaturase (FAD2 gene was identified in our cDNA sequences. Sequence and functional analyses of the castor FAD2 were carried out since it had not been characterized previously. Overexpression of castor FAD2 in a FAH12-expressing Arabidopsis line resulted in decreased accumulation of hydroxy fatty acids in transgenic seeds. Conclusion Our results suggest that transcriptional regulation of FAD2 and FAH12 genes maybe one of the mechanisms that contribute to a high level of ricinoleate accumulation in castor endosperm. The full-length cDNA library will be used to search for additional genes that affect ricinoleate accumulation in seed oils. Our EST sequences will also be useful to annotate the castor genome, which whole sequence is being generated by shotgun sequencing at

  11. Generation and Analysis of Expressed Sequence Tags (ESTs) from Muscle Full-Length cDNA Library of Wujin Pig

    Institute of Scientific and Technical Information of China (English)

    ZHAO Su-mei; LIU Yong-gang; PAN Hong-bing; ZHANG Xi; GE Chang-rong; JIA Jun-jing; GAO Shi-zheng

    2014-01-01

    Porcine skeletal muscle genes play a major role in determining muscle growth and meat quality. Construction of a full-length cDNA library is an effective way to understand the expression of functional genes in muscle tissues. In addition, novel genes for further research could be identiifed in the library. In this study, we constructed a full-length cDNA library from porcine muscle tissue. The estimated average size of the cDNA inserts was 1076 bp, and the cDNA fullness ratio was 86.2%. A total of 1058 unique sequences with 342 contigs (32.3%) and 716 singleton (67.7%) expressed sequence tags (EST) were obtained by clustering and assembling. Meanwhile, 826 (78.1%) ESTs were categorized as known genes, and 232 (21.9%) ESTs were categorized as unknown genes. 65 novel porcine genes that exhibit no identity in the TIGR gene index ofSus scrofa and 124 full-length sequences with unknown functions were deposited in the dbEST division of GenBank (accession numbers: EU650784-EU650788, GE843306, GH228978-GH229100). The abundantly expressed genes in porcine muscle tissue were related to muscle ifber development, energy metabolism and protein synthesis. Gene ontology analysis showed that sequences expressed in porcine muscle tissue contained a high percentage of binding activity, catalytic activity, structural molecule activity and motor activity, which involved mainly in metabolic, cellular and developmental process, distributed mainly in intracellular region. The sequence data generated in this study would provide valuable information for identifying porcine genes expressed in muscle tissue and help to advance the study on the structure and function of genes in pigs.

  12. Comparative analysis of taxonomic, functional, and metabolic patterns of microbiomes from 14 full-scale biogas reactors by metagenomic sequencing and radioisotopic analysis

    DEFF Research Database (Denmark)

    Luo, Gang; Fotidis, Ioannis; Angelidaki, Irini

    2016-01-01

    analysis showed higher relative abundance of hydrogenotrophic methanogens. Principal coordinates analysis showed the sludge-based samples were clearly distinct from the manure-based samples for both taxonomic and functional patterns, and canonical correspondence analysis showed that the both temperature......, and their relationships with the metabolic patterns. The present study used metagenomic sequencing and radioisotopic analysis to assess the taxonomic, functional, and metabolic patterns of microbiomes from 14 full-scale biogas reactors operated under various conditions treating either sludge or manure. Results...... The results from metagenomic analysis showed that the dominant methanogenic pathway revealed by radioisotopic analysis was not always correlated with the taxonomic and functional compositions. It was found by radioisotopic experiments that the aceticlastic methanogenic pathway was dominant, while metagenomics...

  13. Full in-plane strain tensor analysis using the microscale ring-core FIB milling and DIC approach

    Science.gov (United States)

    Lunt, Alexander J. G.; Salvati, Enrico; Ma, Lifeng; Dolbyna, Igor P.; Neo, Tee K.; Korsunsky, Alexander M.

    2016-09-01

    Microscale Full In-plane Strain Tensor (FIST) analysis is crucial for improving understanding of residual stress and mechanical failure in many applications. This study outlines the first Focused Ion Beam (FIB) milling and Digital Image Correlation (DIC) based technique capable of performing precise, reliable and rapid quantification of this behaviour. The nature of semi-destructive FIB milling overcomes the main limitations of X-Ray Diffraction (XRD) strain tensor quantification: unstrained lattice parameter estimates are not required, analysis is performed in within a precisely defined 3D microscale volume, both amorphous and crystalline materials can be studied and access to X-ray/neutron facilities is not required. The FIST FIB milling and DIC experimental technique is based on extending the ring-core milling geometry to quantify the strain variation with angle and therefore benefits from the excellent precision and simple analytical approach associated with this method. In this study in-plane strain analysis was performed on sample of commercial interest: a porcelain veneered Yttria Partially Stabilised Zirconia (YPSZ) dental prosthesis, and was compared with the results of XRD. The two methods sample different gauge volumes and mechanical states: approximately plane stress for ring-core milling, and a through-thickness average for XRD. We demonstrate using complex analysis methods and Finite Element (FE) modelling that valid comparisons can be drawn between these two stress states. Excellent agreement was obtained between principal stress orientation and magnitudes, leading to realistic residual stress estimates that agree well with the literature (σAv ≈ 460 MPa) . As a measure of validity of the matching approach we report the upper and lower bounds on the (101) interplanar spacing of YPSZ that are found to correspond to the range 2.9586 - 2.9596 Å , closely matching published values.

  14. New Spectral Fitting Method for Full-Spectrum Solar-Induced Chlorophyll Fluorescence Retrieval Based on Principal Components Analysis

    Directory of Open Access Journals (Sweden)

    Xinjie Liu

    2015-08-01

    Full Text Available The full-spectrum Solar-Induced chlorophyll Fluorescence (SIF within the 650-800 nm spectral region can provide important information regarding physiological and biochemical activities in vegetation. This paper proposes a new Full-spectrum Spectral Fitting Method (F-SFM for the retrieval of SIF spectra based on Principal Components Analysis (PCA. Using F-SFM, both the full-spectrum reflectance and SIF within the 650-800 nm region were modeled by PCA based on a training dataset simulated by the Soil Canopy Observation, Photochemistry and Energy fluxes (SCOPE model, and the weighting coefficients of the principal components were estimated by the least-squares fitting method. An iterative process was employed to improve the accuracy of the estimation of the reflectance. In each iteration, the SIF spectra retrieved from the last run were removed from the total upwelling radiance to minimize the small contribution of the SIF to the apparent reflectance outside the absorption bands. Then, the F-SFM algorithm was tested using both simulated and field-measured data with different Spectral Resolutions (SRs and Signal-to-Noise Ratios (SNRs. For data with an SR of 0.3 nm and without noise, the Relative Root Mean Square Error (RRMSE was less than 14% within the spectral region that was studied, and the peak-value ratio (SIF735/SIF685 was accurately estimated with an RRMSE of 3.56%. In addition, the F-SFM algorithm proved less sensitive to the SR than the three-band Fraunhofer Line Discrimination (3 FLD and improved FLD (iFLD methods. In the case of the field spectral data with SRs of 3 nm and 0.3 nm, the double-peak shape and the diurnal variation trend of the SIF spectra could be reasonably reconstructed by F-SFM, and the retrieved SIF values at the O2-A and O2-B bands were consistent with those retrieved by 3FLD from data with a high SR (0.3 nm and SNR (1000. Therefore, the F-SFM method can provide full-spectrum SIF information with high accuracy even at

  15. Economic analysis of microaerobic removal of H2S from biogas in full-scale sludge digesters.

    Science.gov (United States)

    Díaz, I; Ramos, I; Fdz-Polanco, M

    2015-09-01

    The application of microaerobic conditions during sludge digestion has been proven to be an efficient method for H2S removal from biogas. In this study, three microaerobic treatments were considered as an alternative to the technique of biogas desulfurization applied (FeCl3 dosing to the digesters) in a WWTP comprising three full-scale anaerobic reactors treating sewage sludge, depending on the reactant: pure O2 from cryogenic tanks, concentrated O2 from PSA generators, and air. These alternatives were compared in terms of net present value (NPV) with a fourth scenario consisting in the utilization of iron-sponge-bed filter inoculated with thiobacteria. The analysis revealed that the most profitable alternative to FeCl3 addition was the injection of concentrated O2 (0.0019 €/m(3) biogas), and this scenario presented the highest robustness towards variations in the price of FeCl3, electricity, and in the H2S concentration.

  16. Hydrostratigraphic analysis of the MADE site with full-resolution GPR and direct-push hydraulic profiling

    Science.gov (United States)

    Dogan, M.; Van Dam, R. L.; Bohling, G.C.; Butler, J.J.; Hyndman, D.W.

    2011-01-01

    Full-resolution 3D Ground-Penetrating Radar (GPR) data were combined with high-resolution hydraulic conductivity (K) data from vertical Direct-Push (DP) profiles to characterize a portion of the highly heterogeneous MAcro Dispersion Experiment (MADE) site. This is an important first step to better understand the influence of aquifer heterogeneities on observed anomalous transport. Statistical evaluation of DP data indicates non-normal distributions that have much higher similarity within each GPR facies than between facies. The analysis of GPR and DP data provides high-resolution estimates of the 3D geometry of hydrostratigraphic zones, which can then be populated with stochastic K fields. The lack of such estimates has been a significant limitation for testing and parameterizing a range of novel transport theories at sites where the traditional advection-dispersion model has proven inadequate. ?? 2011 by the American Geophysical Union.

  17. Vectorial acylation in Saccharomyces cerevisiae. Fat1p and fatty acyl-CoA synthetase are interacting components of a fatty acid import complex

    DEFF Research Database (Denmark)

    Zou, Zhiying; Tong, Fumin; Færgeman, Nils J.

    2003-01-01

    In Saccharomyces cerevisiae Fat1p and fatty acyl-CoA synthetase (FACS) are hypothesized to couple import and activation of exogenous fatty acids by a process called vectorial acylation. Molecular genetic and biochemical studies were used to define further the functional and physical interactions ...

  18. Sequencing and analysis of 10967 full-length cDNA clones from Xenopus laevis and Xenopus tropicalis

    Energy Technology Data Exchange (ETDEWEB)

    Morin, R D; Chang, E; Petrescu, A; Liao, N; Kirkpatrick, R; Griffith, M; Butterfield, Y; Stott, J; Barber, S; Babakaiff, R; Matsuo, C; Wong, D; Yang, G; Smailus, D; Brown-John, M; Mayo, M; Beland, J; Gibson, S; Olson, T; Tsai, M; Featherstone, R; Chand, S; Siddiqui, A; Jang, W; Lee, E; Klein, S; Prange, C; Myers, R M; Green, E D; Wagner, L; Gerhard, D; Marra, M; Jones, S M; Holt, R

    2005-10-31

    Sequencing of full-insert clones from full-length cDNA libraries from both Xenopus laevis and Xenopus tropicalis has been ongoing as part of the Xenopus Gene Collection initiative. Here we present an analysis of 10967 clones (8049 from X. laevis and 2918 from X. tropicalis). The clone set contains 2013 orthologs between X. laevis and X. tropicalis as well as 1795 paralog pairs within X. laevis. 1199 are in-paralogs, believed to have resulted from an allotetraploidization event approximately 30 million years ago, and the remaining 546 are likely out-paralogs that have resulted from more ancient gene duplications, prior to the divergence between the two species. We do not detect any evidence for positive selection by the Yang and Nielsen maximum likelihood method of approximating d{sub N}/d{sub S}. However, d{sub N}/d{sub S} for X. laevis in-paralogs is elevated relative to X. tropicalis orthologs. This difference is highly significant, and indicates an overall relaxation of selective pressures on duplicated gene pairs. Within both groups of paralogs, we found evidence of subfunctionalization, manifested as differential expression of paralogous genes among tissues, as measured by EST information from public resources. We have observed, as expected, a higher instance of subfunctionalization in out-paralogs relative to in-paralogs.

  19. Full factorial experimental design analysis of Rhodamine B removal from water using organozeolite from coal bottom ash

    Directory of Open Access Journals (Sweden)

    Raquel R. Alcântara, Rafael O. R. Muniz, Denise A. Fungaro

    2016-01-01

    Full Text Available Zeolitic material synthesized using coal bottom ash asraw materialwas modified by cationic surfactant. Raw bottom ash and zeolitic materials were characterized using various techniques to obtain its physical and chemical properties. Surfactant modified zeolite (SMZBA was used as alternative low-cost adsorbent for removal of Rhodamine B (RB dye from aqueous solution. Dye adsorption equilibrium was attained after 40 min of the contact time and adsorption kinetics were described by the pseudo second order kinetic model. Equilibrium adsorption data were adjusted using non-linear equations of the Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R models. Error analysis showed that D-R was the most appropriate for fitting the experimental data.The reuse of the remaining solution generated from the synthesis of zeolite was effective. To optimize the operating conditions, the temperature, pH, adsorbent dosage and initial concentration of the dye were investigated by full factorial experimental design method; adsorbent dosage, initial concentration and interaction of the two were found as the most significant factors with P = 0.02 lower than 95% confidence level. The results showed that SMZBA is a good adsorbent for the removal of RB from aqueous effluent.

  20. A comparative phylogenetic analysis of full-length mariner elements isolated from the Indian tasar silkmoth, Antheraea mylitta (Lepidoptera: saturniidae)

    Indian Academy of Sciences (India)

    M Dharma Prasad; J Nagaraju

    2003-06-01

    Mariner like elements (MLEs) are widely distributed type II transposons with an open reading frame (ORF) for transposase. We studied comparative phylogenetic evolution and inverted terminal repeat (ITR) conservation of MLEs from Indian saturniid silkmoth, Antheraea mylitta with other full length MLEs submitted in the database. Full length elements from A. mylitta were inactive with multiple mutations. Many conserved amino acid blocks were identified after aligning transposase sequences. Mariner signature sequence, DD(34)D was almost invariable although a few new class of elements had different signatures. A. mylitta MLEs (Anmmar) get phylogenetically classified under cecropia subfamily and cluster closely with the elements from other Bombycoidea superfamily members implying vertical transmission from a common ancestor. ITR analysis showed a conserved sequence of AGGT(2-8N)ATAAGT for forward repeat and AGGT(2-8N)ATGAAAT for reverse repeat. These results and additional work may help us to understand the dynamics of MLE distribution in A. mylitta and construction of appropriate vectors for mariner mediated transgenics.

  1. Full-Wave Analysis of Stable Cross Fractal Frequency Selective Surfaces Using an Iterative Procedure Based on Wave Concept

    Directory of Open Access Journals (Sweden)

    V. P. Silva Neto

    2015-01-01

    Full Text Available This work presents a full-wave analysis of stable frequency selective surfaces (FSSs composed of periodic arrays of cross fractal patch elements. The shapes of these patch elements are defined conforming to a fractal concept, where the generator fractal geometry is successively subdivided into parts which are smaller copies of the previous ones (defined as fractal levels. The main objective of this work is to investigate the performance of FSSs with cross fractal patch element geometries including their frequency response and stability in relation to both the angle of incidence and polarization of the plane wave. The frequency response of FSS structures is obtained using the wave concept iterative procedure (WCIP. This method is based on a wave concept formulation and the boundary conditions for the FSS structure. Prototypes were manufactured and measured to verify the WCIP model accuracy. A good agreement between WCIP and measured results was observed for the proposed cross fractal FSSs. In addition, these FSSs exhibited good angular stability.

  2. Full-length VP2 gene analysis of canine parvovirus reveals emergence of newer variants in India.

    Science.gov (United States)

    Nookala, Mangadevi; Mukhopadhyay, Hirak Kumar; Sivaprakasam, Amsaveni; Balasubramanian, Brindhalakshmi; Antony, Prabhakar Xavier; Thanislass, Jacob; Srinivas, Mouttou Vivek; Pillai, Raghavan Madhusoodanan

    2016-12-01

    The canine parvovirus (CPV) infection is a highly contagious and serious enteric disease of dogs with high fatality rate. The present study was taken up to characterize the full-length viral polypeptide 2 (VP2) gene of CPV of Indian origin along with the commercially available vaccines. The faecal samples from parvovirus suspected dogs were collected from various states of India for screening by PCR assay and 66.29% of samples were found positive. Six CPV-2a, three CPV-2b, and one CPV-2c types were identified by sequence analysis. Several unique and existing mutations have been noticed in CPV types analyzed indicating emergence of newer variants of CPV in India. The phylogenetic analysis revealed that all the field CPV types were grouped in different subclades within two main clades, but away from the commercial vaccine strains. CPV-2b and CPV-2c types with unique mutations were found to be establishing in India apart from the prevailing CPV-2a type. Mutations and the positive selection of the mutants were found to be the major mechanism of emergence and evolution of parvovirus. Therefore, the incorporation of local strain in the vaccine formulation may be considered for effective control of CPV infections in India.

  3. High-order full-discretization method using Lagrange interpolation for stability analysis of turning processes with stiffness variation

    Science.gov (United States)

    Sun, Yuxin; Xiong, Zhenhua

    2017-01-01

    In turning processes, chatter is an unstable vibration which adversely affects surface finish and machine tool components. Stiffness variation (SV) is an effective strategy for chatter suppression by periodically modulating the stiffness around a nominal value. The dynamics of SV turning is governed by a time periodic delay differential equation (DDE) where the time-period/time-delay ratio (TPTDR) can be arbitrary. Recently, first-, second- and higher-order full-discretization methods (FDMs) have been reported as a popular class of methods for milling stability prediction. However, these FDMs can only deal with time periodic DDE where the TPTDR equals one. In this paper, two high-order FDMs using Lagrange interpolation (HLFDMs) are proposed for stability analysis of SV turning. On each discrete time interval, the time delay term is interpolated by the second-degree Lagrange polynomial, and the time periodic term is linearly interpolated. The state term is approximated using linear interpolation and second-degree Lagrange polynomial interpolation, achieving the first- and second-order HLFDM, respectively. Finally, the transition matrix over a single period is deduced for stability analysis via the Floquet theory. Benchmark examples of damped delay Mathieu equations are used to verify the proposed algorithm, which demonstrates that HLFDMs are highly efficient and accurate. In addition, the second-order HLFDM is used to investigate the effects of SV amplitude and frequency parameters. These results provide theoretical insights for the selection of SV parameters.

  4. Cost-performance analysis of nutrient removal in a full-scale oxidation ditch process based on kinetic modeling

    Institute of Scientific and Technical Information of China (English)

    Zheng Li; Rong Qi; Bo Wang; Zhe Zou; Guohong Wei; Min Yang

    2013-01-01

    A full-scale oxidation ditch process for treating sewage was simulated with the ASM2d model and optimized for minimal cost with acceptable performance in terms of ammonium and phosphorus removal.A unified index was introduced by integrating operational costs (aeration energy and sludge production) with effluent violations for performance evaluation.Scenario analysis showed that,in comparison with the baseline (all of the 9 aerators activated),the strategy of activating 5 aerators could save aeration energy significantly with an ammonium violation below 10%.Sludge discharge scenario analysis showed that a sludge discharge flow of 250-300 m3/day (solid retention time (SRT),13-15 days) was appropriate for the enhancement of phosphorus removal without excessive sludge production.The proposed optimal control strategy was:activating 5 rotating disks operated with a mode of "111100100" ("1"represents activation and "0" represents inactivation) for aeration and sludge discharge flow of 200 m3/day (SRT,19 days).Compared with the baseline,this strategy could achieve ammonium violation below 10% and TP violation below 30% with substantial reduction of aeration energy cost (46%) and minimal increment of sludge production (< 2%).This study provides a useful approach for the optimization of process operation and control.

  5. Collection and comparative analysis of 1888 full-length cDNAs from wild rice Oryza rufipogon Griff. W1943.

    Science.gov (United States)

    Lu, Tingting; Yu, Shuliang; Fan, Danlin; Mu, Jie; Shangguan, Yingying; Wang, Zixuan; Minobe, Yuzo; Lin, Zhixin; Han, Bin

    2008-10-01

    A huge amount of cDNA and EST resources have been developed for cultivated rice species Oryza sativa; however, only few cDNA resources are available for wild rice species. In this study, we isolated and completely sequenced 1888 putative full-length cDNA (FLcDNA) clones from wild rice Oryza rufipogon Griff. W1943 for comparative analysis between wild and cultivated rice species. Two cDNA libraries were constructed from 3-week-old leaf samples under either normal or cold-treated conditions. Homology searching of these cDNA sequences revealed that >96.8% of the wild rice cDNAs were matched to the cultivated rice O. sativa ssp. japonica cv. Nipponbare genome sequence. However, sequence. The comparative analysis showed that O. rufipogon W1943 had greater similarity to O. sativa ssp. japonica than to ssp. indica cultivars. In addition, 17 novel rice cDNAs were identified, and 41 putative tissue-specific expression genes were defined through searching the rice massively parallel signature-sequencing database. In conclusion, these FLcDNA clones are a resource for further function verification and could be broadly utilized in rice biological studies.

  6. Part-time versus full-time occlusion therapy for treatment of amblyopia: A meta-analysis.

    Science.gov (United States)

    Yazdani, Negareh; Sadeghi, Ramin; Momeni-Moghaddam, Hamed; Zarifmahmoudi, Leili; Ehsaei, Asieh; Barrett, Brendan T

    2017-06-01

    To compare full-time occlusion (FTO) and part-time occlusion (PTO) therapy in the treatment of amblyopia, with the secondary aim of evaluating the minimum number of hours of part-time patching required for maximal effect from occlusion. A literature search was performed in PubMed, Scopus, Science Direct, Ovid, Web of Science and Cochrane library. Methodological quality of the literature was evaluated according to the Oxford Center for Evidence Based Medicine and modified Newcastle-Ottawa scale. Statistical analyses were performed using Comprehensive Meta-Analysis (version 2, Biostat Inc., USA). The present meta-analysis included six studies [three randomized controlled trials (RCTs) and three non-RCTs]. Pooled standardized difference in the mean changes in the visual acuity was 0.337 [lower and upper limits: -0.009, 0.683] higher in the FTO as compared to the PTO group; however, this difference was not statistically significant (P = 0.056, Cochrane Q value = 20.4 (P = 0.001), I(2) = 75.49%). Egger's regression intercept was 5.46 (P = 0.04). The pooled standardized difference in means of visual acuity changes was 1.097 [lower and upper limits: 0.68, 1.513] higher in the FTO arm (P < 0.001), and 0.7 [lower and upper limits: 0.315, 1.085] higher in the PTO arm (P < 0.001) compared to PTO less than two hours. This meta-analysis shows no statistically significant difference between PTO and FTO in treatment of amblyopia. However, our results suggest that the minimum effective PTO duration, to observe maximal improvement in visual acuity is six hours per day.

  7. Full-wave and Fokker Planck analysis of ICRF heating experiments in the Alcator C-Mod tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Bonoli, P.T.; Golovato, S.; Porkolab, M.; Takase, Y. [MIT Plasma Fusion Center, Cambridge, MA (United States)

    1996-12-31

    The Alcator C-Mod device is a high field, high density, shaped tokamak with parameters a = 0.22 m, R{sub 0} = 0.67 m, B{sub 0} {le} 9.0 T, {kappa} {le} 1.8, {delta} {le} 0.8, and 1.0 x 10{sup 20} m{sup -3} n{sub e} (0) {le} 1.0 x 10{sup 21} m{sup -3}. Four megawatt of ICRF power is available at 80 MHz. The wide operating range in magnetic field makes several heating schemes possible: (i) Second harmonic heating of hydrogen (f{sub 0} = 2f{sub CH}) at 2.6 T in (D-H); (ii) Fundamental heating of (H) (f{sub 0} = f{sub CH}) at 5.3T in a D-(H) plasma; and (iii) Fundamental heating of ({sup 3}He) (f{sub 0} = f{sub C{sup 3}He}) at 7.9 T in a D-({sup 3}He) plasma. The most successful heating regime to date has been (H)-minority heating at 5.3 T. Pellet enhanced performance (PEP) modes have also been achieved in C-Mod in D-(H) at 5.3 T and in D-({sup 3}He) at 7.9 T, with a combination of intense ICRF heating and Li-pellet injection. A variety of numerical models are used to analyze these heating schemes. A 1-D full-wave code (FELICE) is used to study {open_quotes}single pass{close_quotes} damping of the ICRF wavefront and damping of mode-converted ion Bernstein waves. A toroidal full-wave code (FISIC) is used to study interference and focussing effects of the ICRF waves as well as damping of the ICRF power upon multiple passes of the ICRF wavefront. A combined bounce averaged Fokker Planck and toroidal full-wave code (FPPRF) is used to study the ion tail formation, orbit losses, and the power partition of the ICRF tail to the background electrons and ions. Full-wave and Fokker Planck analyses confirm the strong single pass absorption of the ICRF power in D-(H) at 5.3 T. Analysis of PEP-mode plasmas in D-({sup 3}He) indicates improved wave focussing and {sup 3}He-cyclotron absorption of the ICRF waves relative to L-mode. A dramatic increase in the transfer of {sup 3}He tail power to the background deuterium is also found for PEP-mode plasmas.

  8. A Note on Vectorial AdS$_5$/CFT$_4$ Duality for Spin-$j$ Boundary Theory

    CERN Document Server

    Bae, Jin-Beom; Lal, Shailesh

    2016-01-01

    The vectorial holographic correspondences between higher-spin theories in AdS$_5$ and free vector models on the boundary are extended to the cases where the latter is described by free massless spin-$j$ field. The dual higher-spin theory in the bulk does not include gravity and can only be defined on rigid AdS$_5$ background with $S^4$ boundary. We discuss various properties of these rather special higher-spin theories and calculate their one-loop free energies. We show that the result is proportional to the same quantity for spin-$j$ doubleton treated as if it is a AdS$_5$ field. Finally, we consider even more special case where the boundary theory itself is given by an infinite tower of massless higher-spin fields.

  9. 矢量波场弹性波Kirchhoff偏移%Elastic Kirchhoff migration of vectorial wave-fields

    Institute of Scientific and Technical Information of China (English)

    杜启振; 侯波

    2008-01-01

    Based on Kuo and Dai's vectorial wave-field extrapolation equations, we derive new Kirchhoff migration equations by introducing unit vectors which represent the ray directions at the imaging points of the reflected P- and PS converted-waves. Furthermore, using the slope of the events on shot records and a ray racing procedure, mirror-image reflection points are found and the reflection data are smeared along the Fresnel zone. The migration method proposed in this paper solves two troublesome imaging problems caused by limited receiving aperture and migration artifacts resulting from wave propagation at the velocities of non original wave type. The migration method is applied successfully with model data, demonstrating that the new method is effective and correct.

  10. Full-length genomic analysis of porcine rotavirus strains isolated from pigs with diarrhea in Northern Italy.

    Science.gov (United States)

    Monini, Marina; Zaccaria, Guendalina; Ianiro, Giovanni; Lavazza, Antonio; Vaccari, Gabriele; Ruggeri, Franco M

    2014-07-01

    Group A rotaviruses (RVA) cause acute dehydrating diarrhea in young of man and many animal species, including pigs. Swine RVA has an important economic impact on the farming industry, and pigs represent a potential reservoir for zoonotic transmission of RVA to humans. To investigate the genetic diversity of porcine RVA strains in Italy and identify their possible zoonotic characteristics, 25 RVA-positive feces were collected from diarrheic pigs in Northern Italy, in 2009-2010; all viral strains were characterized by G and P genotyping RT-PCR. Three samples were selected for full genome sequencing. Sequencing of the NSP3 genes of all samples was also performed. Rotavirus diagnosis was carried out by ELISA and electron microscopy. RT-PCR and Sanger sequencing were performed in a one-tube format, using primer sets specific for each of the 11 genome segments. Analysis of the G (VP7) and P (VP4) genotypes showed that all strains identified were typical porcine RVAs (G4, G5, G9; P[6], P[13], P[23]). Full-length genome sequencing was performed on selected G9 isolates. Most segments belonged to the genotype constellation 1 (Wa-like), which is shared by most human RVA strains, but gene types such as I5 (VP6) and A8 (NSP1), which are typical of porcine and rare among human RVAs, were also detected. We identified RVA strains showing the T7 genotype, an NSP3 gene type that was previously reported in unusual strains of possible porcine or bovine origin from children with diarrhea. Recent reports suggested that G9 RVA may have been introduced from swine to human populations involving gene reassortment events. The observation that some of the RVA genotypes from swine in Italy were similar to viruses characterized in children underlines the importance of animal RVA surveillance, to clarify and monitor the role of animals as genetic reservoirs of emerging RVA strains pathogenic for humans.

  11. Vectorial transport of nucleoside analogs from the apical to the basolateral membrane in double-transfected cells expressing the human concentrative nucleoside transporter hCNT3 and the export pump ABCC4.

    Science.gov (United States)

    Rius, Maria; Keller, Daniela; Brom, Manuela; Hummel-Eisenbeiss, Johanna; Lyko, Frank; Keppler, Dietrich

    2010-07-01

    The identification of the transport proteins responsible for the uptake and the efflux of nucleosides and their metabolites enables the characterization of their vectorial transport and a better understanding of their absorption, distribution, and elimination. Human concentrative nucleoside transporters (hCNTs/SLC28A) are known to mediate the transport of natural nucleosides and some nucleoside analogs into cells in a sodium-dependent and unidirectional manner. On the other hand, several human multidrug resistance proteins [human ATP-binding cassette transporter, subfamily C (ABCC)] cause resistance against nucleoside analogs and mediate transport of phosphorylated nucleoside derivatives out of the cells in an ATP-dependent manner. For the integrated analysis of uptake and efflux of these compounds, we established a double-transfected Madin-Darby canine kidney (MDCK) II cell line stably expressing the human uptake transporter hCNT3 in the apical membrane and the human efflux pump ABCC4 in the basolateral membrane. The direction of transport was from the apical to the basolateral compartment, which is in line with the unidirectional transport and the localization of both recombinant proteins in the MDCKII cells. Recombinant hCNT3 mediated the transport of several known nucleoside substrates, and we identified 5-azacytidine as a new substrate for hCNT3. It is of interest that coexpression of both transporters was confirmed in pancreatic adenocarcinomas, which represent an important clinical indication for the therapeutic use of nucleoside analogs. Thus, our results establish a novel cell system for studies on the vectorial transport of nucleosides and their analogs from the apical to the basolateral compartment. The results contribute to a better understanding of the cellular transport characteristics of nucleoside drugs.

  12. Comparative analysis of taxonomic, functional, and metabolic patterns of microbiomes from 14 full-scale biogas reactors by metagenomic sequencing and radioisotopic analysis.

    Science.gov (United States)

    Luo, Gang; Fotidis, Ioannis A; Angelidaki, Irini

    2016-01-01

    Biogas production is a very complex process due to the high complexity in diversity and interactions of the microorganisms mediating it, and only limited and diffuse knowledge exists about the variation of taxonomic and functional patterns of microbiomes across different biogas reactors, and their relationships with the metabolic patterns. The present study used metagenomic sequencing and radioisotopic analysis to assess the taxonomic, functional, and metabolic patterns of microbiomes from 14 full-scale biogas reactors operated under various conditions treating either sludge or manure. The results from metagenomic analysis showed that the dominant methanogenic pathway revealed by radioisotopic analysis was not always correlated with the taxonomic and functional compositions. It was found by radioisotopic experiments that the aceticlastic methanogenic pathway was dominant, while metagenomics analysis showed higher relative abundance of hydrogenotrophic methanogens. Principal coordinates analysis showed the sludge-based samples were clearly distinct from the manure-based samples for both taxonomic and functional patterns, and canonical correspondence analysis showed that the both temperature and free ammonia were crucial environmental variables shaping the taxonomic and functional patterns. The study further the overall patterns of functional genes were strongly correlated with overall patterns of taxonomic composition across different biogas reactors. The discrepancy between the metabolic patterns determined by metagenomic analysis and metabolic pathways determined by radioisotopic analysis was found. Besides, a clear correlation between taxonomic and functional patterns was demonstrated for biogas reactors, and also the environmental factors that shaping both taxonomic and functional genes patterns were identified.

  13. Evaluation of automatic exposure control performance in full-field digital mammography systems using contrast-detail analysis

    Science.gov (United States)

    Suarez Castellanos, Ivan M.; Kaczmarek, Richard; Brunner, Claudia C.; de Las Heras, Hugo; Liu, Haimo; Chakrabarti, Kish

    2012-03-01

    Full Field Digital Mammography (FFDM) is increasingly replacing screen-film systems for screening and diagnosis of breast abnormalities. All FFDM systems are equipped with an Automatic Exposure Control (AEC) which automatically selects technique factors to optimize dose and image quality. It is therefore crucial that AEC performance is properly adjusted and optimized to different breast thicknesses. In this work, we studied the AEC performance of three widely used FFDM systems using the CDMAM and QUART mam/digi phantoms. We used the CDMAM phantom to generate Contrast-Detail (C-D) curves for each AEC mode available in the FFDM systems under study for phantoms with equivalent X-Ray attenuation properties as 3.2 cm, 6 cm and 7.5 cm thick breasts. Generated C-D curves were compared with ideal C-D curves constructed using a metric referred to as the k-factor which is the product of the thickness and the diameter of the smallest correctly identified disks in the CDMAM phantom. Previous observer studies have indicated that k-factor values of 60 to 80 μm2 are particularly useful in demonstrating the threshold for object detectability for detectors used in digital mammography systems. The QUART mam/digi phantom was used to calculate contrast-to-noise ratio (CNR) values at different phantom thicknesses. The results of the C-D analysis and CNR measurements were used to determine limiting CNR values intended to provide a threshold for proper image quality assessment. The results of the Contrast-Detail analysis show that for two of the three evaluated FFDM systems, at higher phantom thicknesses, low contrast signal detectability gets worse. This agrees with the results obtained with the QUART mam/digi phantom, where CNR decreases below determined limiting CNR values.

  14. Noise analysis and characterization of a full differential CMOS interface circuit for capacitive closed-loop micro-accelerometer

    Institute of Scientific and Technical Information of China (English)

    LIU Xiao-wei; LI Hai-tao; YIN Liang; CHEN Wei-ping; SUO Chun-guang; ZHOU Zhi-ping

    2010-01-01

    To achieve a high precision capacitive closed-loop micro-accelerometer,a full differential CMOS based on switched-capacitor circuit was presented in this paper as the sensor interface circuit.This circuit consists of a balance-bridge module,a charge sensitive amplifier,a correlated-double-sampling module,and a logic timing control module.A special two-path feedback circuit configuration was given to improve the system linearity.The quantitative analysis of error voltage and noise shows that there is tradeoff around circuit's noise,speed and accuracy.A detailed design method was given for this tradeoff.The noise performance optimized circuit has a noise root spectral density of 1.0 μV/√Hz,equivalent to rms noise root spectral density of1.63 μg/√Hz.Therefore,the sensor' s Brown noise becomes the main noise source in this design.This circuit is designed with 0.5 μm n-well CMOS process.Under a ± 5 V supply,the Hspice simulation shows that the system sensitivity achieves 0.616 V/g,the system offset is as low as 1.456 mV,the non-linearity is below0.03%,and the system linear range achieves ±5 g.

  15. Analysis of a bending test on a full-scale PWR hot leg elbow containing a surface crack

    Energy Technology Data Exchange (ETDEWEB)

    Delliou, P. le [Electricite de France, EDF, 77 - Moret-sur-Loing (France). Dept. MTC; Julisch, P.; Hippelein, K. [Stuttgart Univ. (Germany). Staatliche Materialpruefungsanstalt; Bezdikian, G. [Electricite de France, EDF, 92 - Paris la Defense (France). Direction Production Transport

    1998-11-01

    EDF, in co-operation with Framatome, has conducted a large research programme on the mechanical behaviour of thermally aged cast duplex stainless steel elbows, which are part of the main primary circuit of French PWR. One important task of this programme consisted of testing a full-scale PWR hot leg elbow. The elbow contained a semi-elliptical circumferential notch machined on the outer surface of the intrados as well as casting defects located on the flanks. To simulate the end-of-life condition of the component regarding material toughness, it had undergone a 2400 hours ageing heat treatment at 400 C. The test preparation and execution, as well as the material characterization programme, were committed to MPA. The test was conducted under constant internal pressure and in-plane bending (opening mode) at 200 C. For safety reasons, it took place on an open air-site: the Meppen military test ground. At the maximum applied moment (6000 kN.m), the notch did not initiate. This paper presents the experimental results and the fracture mechanics analysis of the test, based on finite element calculations. (orig.)

  16. Super-resolved image acquisition with full-field localization-based microscopy: theoretical analysis and evaluation

    Science.gov (United States)

    Son, Taehwang; Lee, Wonju; Kim, Donghyun

    2016-02-01

    We analyze and evaluate super-resolved image acquisition with full-field localization microscopy in which an individual signal sampled by localization may or may not be switched. For the analysis, Nyquist-Shannon sampling theorem based on ideal delta function was extended to sampling with unit pulse comb and surface-enhanced localized near-field that was numerically calculated with finite difference time domain. Sampling with unit pulse was investigated in Fourier domain where magnitude of baseband becomes larger than that of adjacent subband, i.e. aliasing effect is reduced owing to pulse width. Standard Lena image was employed as imaging target and a diffraction-limited optical system is assumed. A peak signal-to-noise ratio (PSNR) was introduced to evaluate the efficiency of image reconstruction quantitatively. When the target was sampled without switching by unit pulse as the sampling width and period are varied, PSNR increased eventually to 18.1 dB, which is the PSNR of a conventional diffraction-limited image. PSNR was found to increase with a longer pulse width due to reduced aliasing effect. When switching of individual sampling pulses was applied, blurry artifact outside the excited field is removed for each pulse and PSNR soars to 25.6 dB with a shortened pulse period, i.e. effective resolution of 72 nm is obtained, which can further be decreased.

  17. Full-wave analysis of the high frequency characteristics of the sine waveguide slow-wave structure

    Science.gov (United States)

    Lei, Xia; Wei, Yanyu; Wang, Yuanyuan; Zhou, Qing; Wu, Gangxiong; Ding, Chong; Li, Qian; Zhang, Luqi; Jiang, Xuebing; Gong, Yubin; Wang, Wenxiang

    2017-08-01

    A theoretical model for calculation of the high frequency characteristics of the sine waveguide slow-wave structure (SWS) is proposed. The formulas of dispersion and interaction impedances of the hybrid modes are obtained by combining the Helmholtz equation with the appropriate boundary conditions. Using the full wave analysis method, it is proved that the periodic structures with a half-period shift followed leads to a pairwise closing of passbands characteristic of adjacent mode. The sine waveguide SWS for 0.22THz traveling wave tube (TWT) is chosen as an illustrative example to verify the validity of the theoretical model, and the calculation results of the dispersion curve and interaction impedance curve are consistent with the HFSS simulation results. In addition, the influences of dimensions of sine waveguide on the high frequency characteristics of +1st spatial harmonic wave are investigated by numerical calculation. The study indicates that the appropriate SWS parameters are helpful for improving the bandwidth and increasing output power of TWT.

  18. Full Genome Sequence Analysis of Two Isolates Reveals a Novel Xanthomonas Species Close to the Sugarcane Pathogen Xanthomonas albilineans

    Directory of Open Access Journals (Sweden)

    Isabelle Pieretti

    2015-07-01

    Full Text Available Xanthomonas albilineans is the bacterium responsible for leaf scald, a lethal disease of sugarcane. Within the Xanthomonas genus, X. albilineans exhibits distinctive genomic characteristics including the presence of significant genome erosion, a non-ribosomal peptide synthesis (NRPS locus involved in albicidin biosynthesis, and a type 3 secretion system (T3SS of the Salmonella pathogenicity island-1 (SPI-1 family. We sequenced two X. albilineans-like strains isolated from unusual environments, i.e., from dew droplets on sugarcane leaves and from the wild grass Paspalum dilatatum, and compared these genomes sequences with those of two strains of X. albilineans and three of Xanthomonas sacchari. Average nucleotide identity (ANI and multi-locus sequence analysis (MLSA showed that both X. albilineans-like strains belong to a new species close to X. albilineans that we have named “Xanthomonas pseudalbilineans”. X. albilineans and “X. pseudalbilineans” share many genomic features including (i the lack of genes encoding a hypersensitive response and pathogenicity type 3 secretion system (Hrp-T3SS, and (ii genome erosion that probably occurred in a common progenitor of both species. Our comparative analyses also revealed specific genomic features that may help X. albilineans interact with sugarcane, e.g., a PglA endoglucanase, three TonB-dependent transporters and a glycogen metabolism gene cluster. Other specific genomic features found in the “X. pseudalbilineans” genome may contribute to its fitness and specific ecological niche.

  19. [Analysis of the molecular characteristics and cloning of full-length coding sequence of interleukin-2 in tree shrews].

    Science.gov (United States)

    Huang, Xiao-Yan; Li, Ming-Li; Xu, Juan; Gao, Yue-Dong; Wang, Wen-Guang; Yin, An-Guo; Li, Xiao-Fei; Sun, Xiao-Mei; Xia, Xue-Shan; Dai, Jie-Jie

    2013-04-01

    While the tree shrew (Tupaia belangeri chinensis) is an excellent animal model for studying the mechanisms of human diseases, but few studies examine interleukin-2 (IL-2), an important immune factor in disease model evaluation. In this study, a 465 bp of the full-length IL-2 cDNA encoding sequence was cloned from the RNA of tree shrew spleen lymphocytes, which were then cultivated and stimulated with ConA (concanavalin). Clustal W 2.0 was used to compare and analyze the sequence and molecular characteristics, and establish the similarity of the overall structure of IL-2 between tree shrews and other mammals. The homology of the IL-2 nucleotide sequence between tree shrews and humans was 93%, and the amino acid homology was 80%. The phylogenetic tree results, derived through the Neighbour-Joining method using MEGA5.0, indicated a close genetic relationship between tree shrews, Homo sapiens, and Macaca mulatta. The three-dimensional structure analysis showed that the surface charges in most regions of tree shrew IL-2 were similar to between tree shrews and humans; however, the N-glycosylation sites and local structures were different, which may affect antibody binding. These results provide a fundamental basis for the future study of IL-2 monoclonal antibody in tree shrews, thereby improving their utility as a model.

  20. CLASH: MASS DISTRIBUTION IN AND AROUND MACS J1206.2-0847 FROM A FULL CLUSTER LENSING ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Umetsu, Keiichi; Koch, Patrick M.; Lin, Kai-Yang [Institute of Astronomy and Astrophysics, Academia Sinica, P.O. Box 23-141, Taipei 10617, Taiwan (China); Medezinski, Elinor [Department of Physics and Astronomy, The Johns Hopkins University, 3400 North Charles Street, Baltimore, MD 21218 (United States); Nonino, Mario [INAF/Osservatorio Astronomico di Trieste, via G. B. Tiepolo 11, 34143 Trieste (Italy); Merten, Julian; Mroczkowski, Tony [Jet Propulsion Laboratory, California Institute of Technology, MS 169-327, Pasadena, CA 91109 (United States); Zitrin, Adi [Institut fuer Theoretische Astrophysik, ZAH, Heidelberg (Germany); Molino, Alberto [Instituto de Astrofisica de Andalucia (CSIC), Granada (Spain); Grillo, Claudio [Dark Cosmology Centre, Niels Bohr Institute, University of Copenhagen, Juliane Mariesvej 30, DK-2100 Copenhagen (Denmark); Carrasco, Mauricio [Centro de Astro-Ingenieria, Departamento de Astronomia y Astrofisica, Pontificia Universidad Catolica de Chile, V. Mackenna 4860, Santiago (Chile); Donahue, Megan [Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Mahdavi, Andisheh [Department of Physics and Astronomy, San Francisco State University, Thornton Hall 527, CA (United States); Coe, Dan; Postman, Marc; Koekemoer, Anton [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21208 (United States); Czakon, Nicole; Sayers, Jack; Golwala, Sunil [Division of Physics, Math, and Astronomy, California Institute of Technology, Pasadena, CA 91125 (United States); Molnar, Sandor M., E-mail: keiichi@asiaa.sinica.edu.tw [LeCosPA Center, National Taiwan University, Taipei 10617, Taiwan (China); and others

    2012-08-10

    We derive an accurate mass distribution of the galaxy cluster MACS J1206.2-0847 (z = 0.439) from a combined weak-lensing distortion, magnification, and strong-lensing analysis of wide-field Subaru BVR{sub c} I{sub c} z' imaging and our recent 16-band Hubble Space Telescope observations taken as part of the Cluster Lensing And Supernova survey with Hubble program. We find good agreement in the regions of overlap between several weak- and strong-lensing mass reconstructions using a wide variety of modeling methods, ensuring consistency. The Subaru data reveal the presence of a surrounding large-scale structure with the major axis running approximately northwest-southeast (NW-SE), aligned with the cluster and its brightest galaxy shapes, showing elongation with a {approx}2: 1 axis ratio in the plane of the sky. Our full-lensing mass profile exhibits a shallow profile slope dln {Sigma}/dln R {approx} -1 at cluster outskirts (R {approx}> 1 Mpc h{sup -1}), whereas the mass distribution excluding the NW-SE excess regions steepens farther out, well described by the Navarro-Frenk-White form. Assuming a spherical halo, we obtain a virial mass M{sub vir} = (1.1 {+-} 0.2 {+-} 0.1) Multiplication-Sign 10{sup 15} M{sub Sun} h{sup -1} and a halo concentration c{sub vir} = 6.9 {+-} 1.0 {+-} 1.2 (c{sub vir} {approx} 5.7 when the central 50 kpc h{sup -1} is excluded), which falls in the range 4 {approx}< (c) {approx}< 7 of average c(M, z) predictions for relaxed clusters from recent {Lambda} cold dark matter simulations. Our full-lensing results are found to be in agreement with X-ray mass measurements where the data overlap, and when combined with Chandra gas mass measurements, they yield a cumulative gas mass fraction of 13.7{sup +4.5}{sub -3.0}% at 0.7 Mpc h{sup -1}( Almost-Equal-To 1.7 r{sub 2500}), a typical value observed for high-mass clusters.

  1. Object-Based Point Cloud Analysis of Full-Waveform Airborne Laser Scanning Data for Urban Vegetation Classification

    Directory of Open Access Journals (Sweden)

    Norbert Pfeifer

    2008-08-01

    Full Text Available Airborne laser scanning (ALS is a remote sensing technique well-suited for 3D vegetation mapping and structure characterization because the emitted laser pulses are able to penetrate small gaps in the vegetation canopy. The backscattered echoes from the foliage, woody vegetation, the terrain, and other objects are detected, leading to a cloud of points. Higher echo densities (> 20 echoes/m2 and additional classification variables from full-waveform (FWF ALS data, namely echo amplitude, echo width and information on multiple echoes from one shot, offer new possibilities in classifying the ALS point cloud. Currently FWF sensor information is hardly used for classification purposes. This contribution presents an object-based point cloud analysis (OBPA approach, combining segmentation and classification of the 3D FWF ALS points designed to detect tall vegetation in urban environments. The definition tall vegetation includes trees and shrubs, but excludes grassland and herbage. In the applied procedure FWF ALS echoes are segmented by a seeded region growing procedure. All echoes sorted descending by their surface roughness are used as seed points. Segments are grown based on echo width homogeneity. Next, segment statistics (mean, standard deviation, and coefficient of variation are calculated by aggregating echo features such as amplitude and surface roughness. For classification a rule base is derived automatically from a training area using a statistical classification tree. To demonstrate our method we present data of three sites with around 500,000 echoes each. The accuracy of the classified vegetation segments is evaluated for two independent validation sites. In a point-wise error assessment, where the classification is compared with manually classified 3D points, completeness and correctness better than 90% are reached for the validation sites. In comparison to many other algorithms the proposed 3D point classification works on the original

  2. Morphology and morphometric analysis of stromal capillaries in full term human placental villi of smoking mothers: an electron microscopic study.

    Science.gov (United States)

    Rath, G; Dhuria, R; Salhan, S; Jain, A K

    2011-01-01

    The capillaries of placental villi play a very important role in the feto-maternal exchange of gases and nutrients. A morphological change in their structure may lead to the impairment of placental function. In this study an attempt has been made to find out the morphological and morphometric features of the capillaries in full term placental villi of non smoking mothers as well as active and passive smoking mothers under an electron microscope. A total number of 163 placentae from active, passive and nonsmoking mother (n = 61+42+60) were processed for electron microscopic study. The ultrathin sections were examined under electron microscope and images were recorded. Morphometry and statistical analysis were carried out with the help of software. The study revealed that the endothelial cells of stromal capillaries of the placental villi were oedematous and the cytoplasm was rich in dilated endoplasmic reticulum, mitochondria, fibrils and fine filaments in both groups of the smokers' placenta in comparison to control. Morphometric analysis showed a significant reduction in the perimeter of the stromal capillary of the tertiary villi of placenta in both active and passive smokers from mean value of 71.65 ± 47.82 µ to mean value of 59.77 ± 29.72 µ (p = 0.07) and 49.49 ± 20.94 µ (p = 0.0005) respectively. In case of passive smoker, area of the capillary (µm²) reduced significantly (p = 0.00004) from mean value of 266.29 ± 331.86 µm² to 116.64 ± 83.62 µm² whereas the number of capillary per villus increased significantly (p = 0.046) from mean value 2.42 ± 1.84 to 4.2 ± 3.16. The thickness of basement membrane of the endothelial cells of stromal capillaries of the placenta increased significantly in active as well as passive smokers (p = 0.00001). The ultrastructural changes noticed in the endothelial cells of placental villi may be due to hypoxia resulting from tobacco consumption either in active or passive form by the pregnant mothers. Thus, targeted

  3. Far-field method for the characterisation of three-dimensional fields: vectorial polarimetry

    Directory of Open Access Journals (Sweden)

    Dainty C.

    2010-06-01

    Full Text Available The first attempt to completely characterise a three-dimensional field was done by Ellis and Dogariu with excellent results reported [1] . However, their method is based on near-field techniques, which limits its range of applications. In this work, we present an alternative far-field method for the characterisation of the three-dimensional field that results from the interaction of a tightly focused three-dimensional field [2] with a sub-resolution specimen. Our method is based on the analysis of the scattering-angle-resolved polarisation state distribution across the exit pupil of a high numerical aperture (NA collector lens using standard polarimetry techniques. Details of the method, the experimental setup built to verify its capabilities, and numerical and first experimental evidence demonstrating that the method allows for high sensitivit y on sub-resolution displacements of a sub-resolution specimen shall be presented [3]. This work is funded by Science Foundation Ireland grant No. 07/IN.1/I906 and Shimadzu Corporation, Japan. Oscar Rodríguez is grateful to the National Council for Science and Technology (CONACYT, Mexico for the Ph D scholarship 177627.

  4. A fast vectorial network analyser for frequencies up to 4 GHz

    Directory of Open Access Journals (Sweden)

    B. Schulte

    2004-01-01

    Full Text Available A fast four channel network analyser is introduced to measure S-parameters in a frequency range from 10MHz to 4GHz. The measurement period of this kind of network analyser is short in comparison with a conventional one, which becomes possible by using highly linear analogue frequency ramps, realized with fractional divider phase locked loop circuits. The settling time for the discrete frequency points, which is typical for a conventional network analyser, is nearly eliminated by the use of frequency ramps. To achieve the necessary bandwidth of 4 GHz in the baseband, a heterodyne principle is applied. A VCO-signal from 5 to 9 GHz is down converted to the baseband with a fixed frequency generator of 9 GHz. The structure of the following network analyser is similar to the structure of a conventional four channel network analyser and therefore all known calibration techniques are suited for the fast network analyser. The intermediate frequency, which is necessary for the evaluation, carries the required information. However a special analysis technique is necessary. This technique is based on two Fourier transformations.

  5. Alpins and thibos vectorial astigmatism analyses: proposal of a linear regression model between methods

    Directory of Open Access Journals (Sweden)

    Giuliano de Oliveira Freitas

    2013-10-01

    Full Text Available PURPOSE: To determine linear regression models between Alpins descriptive indices and Thibos astigmatic power vectors (APV, assessing the validity and strength of such correlations. METHODS: This case series prospectively assessed 62 eyes of 31 consecutive cataract patients with preoperative corneal astigmatism between 0.75 and 2.50 diopters in both eyes. Patients were randomly assorted among two phacoemulsification groups: one assigned to receive AcrySof®Toric intraocular lens (IOL in both eyes and another assigned to have AcrySof Natural IOL associated with limbal relaxing incisions, also in both eyes. All patients were reevaluated postoperatively at 6 months, when refractive astigmatism analysis was performed using both Alpins and Thibos methods. The ratio between Thibos postoperative APV and preoperative APV (APVratio and its linear regression to Alpins percentage of success of astigmatic surgery, percentage of astigmatism corrected and percentage of astigmatism reduction at the intended axis were assessed. RESULTS: Significant negative correlation between the ratio of post- and preoperative Thibos APVratio and Alpins percentage of success (%Success was found (Spearman's ρ=-0.93; linear regression is given by the following equation: %Success = (-APVratio + 1.00x100. CONCLUSION: The linear regression we found between APVratio and %Success permits a validated mathematical inference concerning the overall success of astigmatic surgery.

  6. Meta-analysis reveals association between most common class II haplotype in full-heritage Native Americans and rheumatoid arthritis.

    Science.gov (United States)

    Williams, R C; Jacobsson, L T; Knowler, W C; del Puente, A; Kostyu, D; McAuley, J E; Bennett, P H; Pettitt, D J

    1995-01-01

    The association of RA with the alleles at the HLA system was tested among Pima and Tohono O'odham Indians (Pimans) of the Gila River Indian Community of Arizona. Serologic class I (HLA-A, -B, and -C) alleles were typed in 51 individuals with RA and in 302 without RA. Serologic class II (HLA-DR, DQ; DR52 DR53) alleles were typed in a subset of 47 with RA and 147 without RA. Molecular subtypes of DR3X6, DRB1*1402, and *1406 were determined in 29 individuals, 16 with RA and 13 without RA. Among the cases with RA, 46 of 47 had the serologic antigen HLA-DR3X6, as did 140 of 147 of those without the disease. However, this association was not statistically significant because of the high prevalence of the antigen in the controls. Data from Pimans were analyzed with similar results from the Tlingit and Yakima Indians. A meta-analysis employing the Mantel-Haenszel procedure, stratified by tribe, revealed a statistically significant association between the most common haplotype, DRB1*1402 DQA1*0501 DQB1*0301 DRB3*0101, and RA (summary odds ratio = 2.63, 95% confidence interval = 1.08, 6.46). There was also a statistically significant difference in the genotype distributions of one class I locus, HLA-C, between those with and without RA (chi 2 = 12.4, 5 df; p = 0.03). It is concluded that the association with the most common class II haplotype in full-heritage Native Americans might help explain their high prevalence of RA.

  7. Phase Velocity and Full-Waveform Analysis of Co-located Distributed Acoustic Sensing (DAS) Channels and Geophone Sensor

    Science.gov (United States)

    Parker, L.; Mellors, R. J.; Thurber, C. H.; Wang, H. F.; Zeng, X.

    2015-12-01

    A 762-meter Distributed Acoustic Sensing (DAS) array with a channel spacing of one meter was deployed at the Garner Valley Downhole Array in Southern California. The array was approximately rectangular with dimensions of 180 meters by 80 meters. The array also included two subdiagonals within the rectangle along which three-component geophones were co-located. Several active sources were deployed, including a 45-kN, swept-frequency, shear-mass shaker, which produced strong Rayleigh waves across the array. Both DAS and geophone traces were filtered in 2-Hz steps between 4 and 20 Hz to obtain phase velocities as a function of frequency from fitting the moveout of travel times over distances of 35 meters or longer. As an alternative to this traditional means of finding phase velocity, it is theoretically possible to find the Rayleigh-wave phase velocity at each point of co-location as the ratio of DAS and geophone responses, because DAS is sensitive to ground strain and geophones are sensitive to ground velocity, after suitable corrections for instrument response (Mikumo & Aki, 1964). The concept was tested in WPP, a seismic wave propagation program, by first validating and then using a 3D synthetic, full-waveform seismic model to simulate the effect of increased levels of noise and uncertainty as data go from ideal to more realistic. The results obtained from this study provide a better understanding of the DAS response and its potential for being combined with traditional seismometers for obtaining phase velocity at a single location. This analysis is part of the PoroTomo project (Poroelastic Tomography by Adjoint Inverse Modeling of Data from Seismology, Geodesy, and Hydrology, http://geoscience.wisc.edu/feigl/porotomo).

  8. Proteomic analysis of HUH-7 cells harboring in vitro-transcribed full-length hepatitis C virus 1b RNA

    Institute of Scientific and Technical Information of China (English)

    Meng XUN; Si-hai ZHAO; Chun-xia CAO; Juan SONG; Ming-ming SHAO; Yong-lie CHU

    2008-01-01

    Aim: The present study examined the differential expression of proteins in HuH-7 cells and HUH-7 cells harboring in vitro-transcribed full-length hepatitis C virus 1b RNA (HuH-7-HCV), and elucidated the cellular responses to HCV replication. Methods: The protein profiles of matched pairs of HuH-7-HCV cells and HUH-7 mock cells were analyzed by 2-D electrophoresis (2DE). Solubilized proteins were separated in the first dimension by isoelectric focusing, and by 12.5% SDS-PAGE in the second dimension. The differential protein expression was analyzed by use of image analysis software to identify candidates for HCV infection-associated proteins. Results: In total, 29 protein spots showed increases and 25 protein spots showed decreases in signal in HuH-7-HCV cell 2DE profiles as compared with HuH-7 mock cells. In the next step, the 10 spots showing the greatest in-crease and the 10 spots showing the greatest decrease were excised from gels and the proteins present were identified by Matrix-Assisted Laser Desorption/Ioniza-tion Time of Flight Mass Spectrometer (MALDI-TOF MS) or MALDI-TOF/TOF MS. In total, 13 proteins were identified successfully. The potential significance of the differential expression due to HCV replication was discussed. Conclusion: Our study identifies changes in the proteome of HuH-7 cells in the presence of HCV replication and yields information of the mechanism of HCV pathogenesis. These results will be useful for the identification of HCV infection-associated proteins that could be molecular targets for treatment.

  9. The Coexistence of Coping Resources and Specific Coping Styles in Stress: Evidence from Full Information Item Bifactor Analysis

    Science.gov (United States)

    Cui, Meng; Wu, Qing; Zhu, Xia; Miao, Danmin; Zhang, Yan; Feng, Xi; Xiao, Wei

    2014-01-01

    Background Knowledge of coping styles is useful in clinical diagnosis and suggesting specific therapeutic interventions. However, the latent structures and relationships between different aspects of coping styles have not been fully clarified. A full information item bifactor model will be beneficial to future research. Objective One goal of this study is identification of the best fit statistical model of coping styles. A second goal is entails extended analyses of latent relationships among different coping styles. In general, such research should offer greater understanding of the mechanisms of coping styles and provide insights into coping with stress. Methods Coping Styles Questionnaire (CSQ) and Generalized Self-Efficacy Scale (GSES) were administrated to officers suffering from military stress. Confirmatory Factor Analyses was performed to indentify the best fit model. A hierarchical item response model (bifactor model) was adopted to analyze the data. Additionally, correlations among coping styles and self-efficacy were compared using both original and bifactor models. Results Results showed a bifactor model best fit the data. Item loadings on general and specific factors varied among different coping styles. All items loaded significantly on the general factor, and most items also had moderate to large loadings on specific factors. The correlation between coping styles and self-efficacy and the correlation among different coping styles changed significantly after extracting the general factor of coping stress using bifactor analysis. This was seen in changes from positive (r = 0.714, pstyles have a bifactor structure. They also provide direct evidence of coexisting coping resources and styles. This further clarifies that dimensions of coping styles should include coping resources and specific coping styles. This finding has implications for measurement of coping mechanisms, health maintenance, and stress reduction. PMID:24787952

  10. Identification and expression analysis of a full-length cDNA encoding a Kandelia candel tonoplast intrinsic protein.

    Science.gov (United States)

    Huang, Wei; Fang, Xiao-Dong; Lin, Qi-Fen; Li, Guan-Yi; Zhao, Wen-Ming

    2003-03-01

    corresponding to the 5' end of this gene was obtained using the GSP2 primer. Two primers that flank the putative open reading frame (ORF) were designed to obtain the cDNA containing the complete ORF by RACE PCR reaction. The full-length cDNA of KCTIP1, containing a 756 bp open reading frame (ORF), was approximately 1.1 kb; the start codon was located at the nucleotides of 99-101 and stop codon at the nucleotides of 855-857 followed by a poly (A) tail. The KCTIP1 cDNA sequence in this research was released in GenBank with accession number AF521135. Using ExPASy Proteomics tools provided by EMBL, the isoelectric point and MWt of KCTIP1 are estimated as 5.77 and 26.3 kD respectively. Transmembrane prediction analysis revealed the deduced KCTIP1 protein sequence contains six transmembrane regions at amino acid residues of 20 - 42, 57 - 79, 86 - 108, 113 - 135, 142 - 164 and 217 - 239. Two highly conserved asparagine-proline-alanine (NPA) motifs were located at 85 - 87 and 199 - 201 amino acid residues respectively. KCTIP1 is also predicted to contain the Cys residue (Cys 118) that are shown to confer Hg-sensitivity in Arabidopsis gamma-TIP and delta-TIP. Similarity analysis showed that KCTIP1 shared 77% - 79% amino acid sequence identity with the TIPs from Vitis berlandieri, Brassica oleracea and Arabidopsis thaliana. Expression analyses indicated that KCTIP1 had different expression among species of Mangroves. Expressions of KCTIP1 in Kandelia candel, Rhizophora apoculata and Ceriops tagal were suppressed by salt, and were insensitive to salt stress in unknown species of Mangroves. Previous studied showed that salt conditions might result in large and rapid changes in extracellular water potential and serious disturbance to the cytoplasm. In order to compensate for this imbalance, the relative contribution of water channels to flow across the root could thus vary. K. candel is a species that is native to intertial zone of tropical and subtropical coast and is well-adapted to salt

  11. Analysis, scale modeling, and full-scale test of a railcar and spent-nuclear-fuel shipping cask in a high-velocity impact against a rigid barrier

    Energy Technology Data Exchange (ETDEWEB)

    Huerta, M.

    1981-06-01

    This report describes the mathematical analysis, the physical scale modeling, and a full-scale crash test of a railcar spent-nuclear-fuel shipping system. The mathematical analysis utilized a lumped-parameter model to predict the structural response of the railcar and the shipping cask. The physical scale modeling analysis consisted of two crash tests that used 1/8-scale models to assess railcar and shipping cask damage. The full-scale crash test, conducted with retired railcar equipment, was carefully monitored with onboard instrumentation and high-speed photography. Results of the mathematical and scale modeling analyses are compared with the full-scale test. 29 figures.

  12. Full Body Gait Analysis May Improve Diagnostic Discrimination Between Hereditary Spastic Paraplegia and Spastic Diplegia: A Preliminary Study

    Science.gov (United States)

    Bonnefoy-Mazure, A.; Turcot, K.; Kaelin, A.; De Coulon, G.; Armand, S.

    2013-01-01

    Hereditary spastic paraplegia (HSP) and spastic diplegia (SD) patients share a strong clinical resemblance. Thus, HSP patients are frequently misdiagnosed with a mild form of SD. Clinical gait analysis (CGA) has been highlighted as a possible tool to support the differential diagnosis of HSP and SD. Previous analysis has focused on the lower-body…

  13. Research on Algebraic Immunity of Vectorial Boolean Functions%向量布尔函数代数免疫性质研究

    Institute of Scientific and Technical Information of China (English)

    王永娟; 孙宇

    2013-01-01

    By discussing the algebraic degree of the annihilators of vectorial Boolean functions, it is found that the algebraic immunity of vectorial Boolean functions remains invariant after affine transformation of the input variables. And after permutation of the output variables, the algebraic immunity also remains invariant. The relations between the Hamming weight of Component functions, the algebraic immunity, Walsh spectrum and the nonlinearity of vectorial Boolean functions were also investigated.%通过讨论向量布尔函数零化子的代数次数,对向量布尔函数的代数免疫性质进行研究,得出其置换不变性,即在输入变量作仿射变换和输出变量作置换之后仍然保持不变,并得出向量布尔函数代数免疫与线性组合函数重量、Walsh谱以及非线性度之间的关系.

  14. Dynamic full field optical coherence tomography: subcellular metabolic contrast revealed in tissues by temporal analysis of interferometric signals

    CERN Document Server

    Apelian, Clement; Thouvenin, Olivier; Boccara, A Claude

    2016-01-01

    We developed a new endogenous approach to reveal subcellular metabolic contrast in fresh ex vivo tissues taking advantage of the time dependence of the full field optical coherence tomography interferometric signals. This method reveals signals linked with local activity of the endogenous scattering elements which can reveal cells where other imaging techniques fail or need exogenous contrast agents. We benefit from the micrometric transverse resolution of full field OCT to image intracellular features. We used this time dependence to identify different dynamics at the millisecond scale on a wide range of organs in normal or pathological conditions.

  15. Improved near-field calculations using vectorial diffraction integrals in the finite-difference time-domain method.

    Science.gov (United States)

    Coe, Ryan L; Sebiel, Eric J

    2011-08-01

    We present an alternative mixed-surface implementation of the Stratton-Chu vectorial diffraction integrals as a means to improve near-field calculations outside the computational domain of the finite-difference time-domain method. This approach, originally derived for far-field calculations, reduces the effect of phase errors and reduces storage costs compared to standard single-surface implementations performed using arithmetic and geometric means. All three methods are applied to a strongly forward-scattering sphere, which is the gold standard for similar simulations with a corresponding analytical Mie series solution. Additionally, the mixed surface is applied to an ensemble of theoretical flow cytometry calibration standards in optical gel. The near-field electromagnetic scattering produced by these or any arbitrary object, such as a cell, could be used to simulate images in a high-numerical-aperture microscope. The results show the mixed-surface implementation outperforms the standard techniques for calculating the near-field electromagnetic fields.

  16. An entomological and seroepidemiological study of the vectorial-transmission risk of Chagas disease in the coast of northern Chile.

    Science.gov (United States)

    González, C R; Reyes, C; Canals, A; Parra, A; Muñoz, X; Rodríguez, K

    2015-12-01

    Four species of triatomines are known from Chile: Triatoma infestans Klug, Mepraia spinolai Porter, M. gajardoi Frías, Henry & González, and M. parapatrica Frías (Hemiptera: Reduviidae), the last three are endemic. The geographical distribution of M. gajardoi includes the coastal areas in the north of Chile between 18° and 21°S, an area with both a resident workforce and summer-season visitors. A study was developed to assess the risk of vectorial transmission of Chagas disease by M. gajardoi in hut settlements on the coast of the Tarapacá Region, in particular in Caleta San Marcos and Caleta Río Seco. The study comprised fingerstick sampling of 95 persons, venous samples from 29 domestic dogs and capture of 52 triatomines, from both fishing coves. The samples were analysed by enzyme-linked immunosorbent assay (ELISA) and polymerase chain reaction (PCR) techniques. The results show that, of the total number of persons studied, 100% were negative for Trypanosoma cruzi Chagas (Trypanosomatida: Trypanosomatidae) antibodies, 10.34% of canids were positive for the antibody and 5.8% of M. gajardoi were infected to the PCR technique. The presence of this species in areas close to human settlements constitutes a risk to human populations established on the coast of northern Chile.

  17. Vectorial competence of Phlebotomus papatasi (Diptera: Psychodidae) to transmit two old world Leishmania species: Leishmania major and L. Tropica.

    Science.gov (United States)

    Darwish, A B; Tewfick, M K; Doha, S A; Abo-Ghalia, A H; Soliman, B A

    2011-12-01

    The vectorial competence of Phlebotomus papatasi for two old world Leishmania species, L. major & L. tropica was investigated. Phlebotomus papatasi originally collected from Suez Governorate, were membrane fed on homogenized hamster's lesion infected with L. major, MHOM/EG/06/RTC-63, and L. tropica, MGER/EG/06/RTC-74 identified from patients with suspected CL in Northern Sinai, Egypt. Fed flies were dissected at different time intervals and examined microscopically to determine the infection rate and parasite intensity. The feeding rate of P. papatasi on L. major (58.69%) was found higher than on L. tropica (45.99%). Infection rate with L. major (60.19%) was significantly higher than that with L. tropica (39.73%). Transmission by bites in case of P. papatasi/L. tropica failed. A characteristic L. major lesion was developed on the foot pads region 120 days post infective bites on healthy hamster. It is therefore concluded that P. papatasi is a much more effective vector for L. major than for L. tropica.

  18. Evaluation of the vectorial capacity of Rhipicephalus sanguineus (Acari: Ixodidae) in the transmission of canine visceral leishmaniasis.

    Science.gov (United States)

    Paz, Gustavo Fontes; Ribeiro, Múcio Flávio Barbosa; Michalsky, Erika Monteiro; da Rocha Lima, Ana Cristina Vianna Mariano; França-Silva, João Carlos; Barata, Ricardo Andrade; Fortes-Dias, Consuelo Latorre; Dias, Edelberto Santos

    2010-01-01

    The vectorial capacity of Rhipicephalus sanguineus in the transmission of canine visceral leishmaniasis has been evaluated through a laboratory-controlled experiment. One healthy Leishmania-free dog and two dogs naturally infected with Leishmania were infested with R. sanguineus in various stages of development. Engorged larvae, unfed nymphs, engorged nymphs, unfed adults, engorged female adults and fed male adults were collected from the experimental animals and examined for Leishmania infection by optical microscopy, polymerase chain reaction (PCR) and parasite culture. Leishmania forms were not detected in any of the 433 smears prepared from engorged colonies nor in any of the 118 smears prepared from unfed colonies. However, one flagellate structure was identified in one of the smears. All pools of R. sanguineus that had fed on the infected dogs tested PCR-positive for Leishmania DNA, with the single exception of the pool of engorged larvae. In contrast, all pools of ticks that had fed on the Leishmania-free dog were PCR-negative. Leishmania growth was not observed in any of the tick colonies following incubation on culture medium. Considering that no Leishmania forms were identified in any of the meticulously analysed smears derived from engorged colonies of R. sanguineus, it appears somewhat unlikely that the maintenance and multiplication of Leishmania occurs within the tick.

  19. Long-term performance and fouling analysis of full-scale direct nanofiltration (NF) installations treating anoxic groundwater

    NARCIS (Netherlands)

    Beyer, F.; Rietman, B.M.; Zwijnenburg, A.; Brink, van den P.; Vrouwenvelder, J.S.; Jarzembowska, M.; Laurinonyte, J.; Stams, A.J.M.; Plugge, C.M.

    2014-01-01

    Long-term performance and fouling behavior of four full-scale nanofiltration (NF) plants, treating anoxic groundwater at 80% recovery for drinking water production, were characterized and compared with oxic NF and reverse osmosis systems. Plant operating times varied between 6 and 10 years and pretr

  20. Crystallization and preliminary X-ray diffraction analysis of full-length and proteolytically activated pyruvate oxidase from Escherichia coli

    Energy Technology Data Exchange (ETDEWEB)

    Weidner, Annett; Neumann, Piotr; Wille, Georg; Stubbs, Milton T.; Tittmann, Kai, E-mail: kai.tittmann@biochemtech.uni-halle.de [Martin-Luther-Universität Halle-Wittenberg, Naturwissenschaftliche Fakultät I, Institut für Biochemie und Biotechnologie, Kurt-Mothes-Strasse 3, D-06120 Halle (Germany)

    2008-03-01

    The peripheral membrane flavoprotein pyruvate oxidase from E. coli has been crystallized in the full-length form and as a proteolytically activated truncation variant lacking the last 23 amino acids at the C-terminus. The thiamine diphosphate- and flavin-dependent peripheral membrane enzyme pyruvate oxidase from Escherichia coli (EcPOX) has been crystallized in the full-length form and as a proteolytically activated C-terminal truncation variant which lacks the last 23 amino acids (Δ23 EcPOX). Crystals were grown by the hanging-drop vapour-diffusion method using either protamine sulfate (full-length EcPOX) or 2-methyl-2,4-pentanediol (Δ23 EcPOX) as precipitants. Native data sets were collected at a X-ray home source to a resolution of 2.9 Å. The two forms of EcPOX crystallize in different space groups. Whereas full-length EcPOX crystallizes in the tetragonal space group P4{sub 3}2{sub 1}2 with two monomers per asymmetric unit, the crystals of Δ23 EcPOX belong to the orthorhombic space group P2{sub 1}2{sub 1}2{sub 1} and contain 12 monomers per asymmetric unit.

  1. Giardia canis: ultrastructural analysis of G. canis trophozoites transfected with full length G. canis virus cDNA transcripts

    Science.gov (United States)

    Giardia canis virus (GCV) is a double-stranded RNA (dsRNA) virus of the family Totiviridae. In this study, the full-length cDNA of the G. canis virus was constructed in pPoly2/sfinot vector and RNA was transcribed in vitro. Virus-free G. canis trophozoites were transfected with in vitro transcribed ...

  2. Linkage analysis between dominant and co-dominant makers in full-sib families of out-breeding species

    Directory of Open Access Journals (Sweden)

    Alexandre Alonso Alves

    2010-01-01

    Full Text Available As high-throughput genomic tools, such as the DNA microarray platform, have lead to the development of novel genotyping procedures, such as Diversity Arrays Technology (DArT and Single Nucleotide Polymorphisms (SNPs, it is likely that, in the future, high density linkage maps will be constructed from both dominant and co-dominant markers. Recently, a strictly genetic approach was described for estimating recombination frequency (r between co-dominant markers in full-sib families. The complete set of maximum likelihood estimators for r in full-sib families was almost obtained, but unfortunately, one particular configuration involving dominant markers, segregating in a 3:1 ratio and co-dominant markers, was not considered. Here we add nine further estimators to the previously published set, thereby making it possible to cover all combinations of molecular markers with two to four alleles (without epistasis in a full-sib family. This includes segregation in one or both parents, dominance and all linkage phase configurations.

  3. Getting a Read on the App Stores: A Market Scan and Analysis of Children's Literacy Apps. Full Report

    Science.gov (United States)

    Vaala, Sarah; Ly, Anna; Levine, Michael H.

    2015-01-01

    In previous research the "Joan Ganz Cooney Center" and "New America" have characterized the children's educational app market as a "Digital Wild West" (Guernsey, Levine, Chiong & Severns, 2012; Shuler, 2011). The marketplace is chock full of choices but lacks essential information to aid parents' and educators'…

  4. Full environmental life cycle cost analysis of concentrating solar power technology: contribution of externalities to overall energy costs

    NARCIS (Netherlands)

    Corona, B.; Cerrajero, E.; San Miguel, G.

    2016-01-01

    The aim of this work is to investigate the use of Full Environmental Life Cycle Costing (FeLCC) methodology to evaluate the economic performance of a 50 MW parabolic trough Concentrated Solar Power (CSP) plant operating in hybrid mode with different natural gas inputs (between 0% and 30%). The analy

  5. Genome based analysis of a novel Chloroflexi in full-scale anaerobic digesters treating waste activated sludge

    DEFF Research Database (Denmark)

    McIlroy, Simon Jon; Kirkegaard, Rasmus Hansen; Albertsen, Mads;

    Key to optimised design and operation of full-scale anaerobic digesters is an understanding of the organisms responsible. As one of the most abundant phyla in these systems, the Chloroflexi likely make a substantial contribute to system function. Here we apply state-of-the-art molecular methods t...

  6. Full environmental life cycle cost analysis of concentrating solar power technology: contribution of externalities to overall energy costs

    NARCIS (Netherlands)

    Corona, B.; Cerrajero, E.; San Miguel, G.

    2016-01-01

    The aim of this work is to investigate the use of Full Environmental Life Cycle Costing (FeLCC) methodology to evaluate the economic performance of a 50 MW parabolic trough Concentrated Solar Power (CSP) plant operating in hybrid mode with different natural gas inputs (between 0% and 30%). The

  7. Full page insight

    DEFF Research Database (Denmark)

    Cortsen, Rikke Platz

    2014-01-01

    Alan Moore and his collaborating artists often manipulate time and space by drawing upon the formal elements of comics and making alternative constellations. This article looks at an element that is used frequently in comics of all kinds – the full page – and discusses how it helps shape spatio......, something that it shares with the full page in comics. Through an analysis of several full pages from Moore titles like Swamp Thing, From Hell, Watchmen and Promethea, it is made clear why the full page provides an apt vehicle for an apocalypse in comics....

  8. Full page insight

    DEFF Research Database (Denmark)

    Cortsen, Rikke Platz

    2014-01-01

    Alan Moore and his collaborating artists often manipulate time and space by drawing upon the formal elements of comics and making alternative constellations. This article looks at an element that is used frequently in comics of all kinds – the full page – and discusses how it helps shape spatio-t......, something that it shares with the full page in comics. Through an analysis of several full pages from Moore titles like Swamp Thing, From Hell, Watchmen and Promethea, it is made clear why the full page provides an apt vehicle for an apocalypse in comics....

  9. Ecological effects of full and partial protection in the crowded Mediterranean Sea: a regional meta-analysis

    DEFF Research Database (Denmark)

    Giakoumi, Sylvaine; Scianna, Claudia; Plass-Johnson, Jeremiah Grahm

    2017-01-01

    Marine protected areas (MPAs) are a cornerstone of marine conservation. Globally, the number and coverage of MPAs are increasing, but MPA implementation lags in many human-dominated regions. In areas with intense competition for space and resources, evaluation of the effects of MPAs is crucial...... the relationships between the level of protection and MPA size, age, and enforcement. Results revealed significant positive effects of protection for fisheries target species and negative effects for urchins as their predators benefited from protection. Full protection provided stronger effects than partial...... protection. Benefits of full protection for fish biomass were only correlated with the level of MPA enforcement; fish density was higher in older, better enforced, and -interestingly- smaller MPAs. Our finding that even small, well-enforced, fully protected areas can have significant ecological effects...

  10. Full-length sequence analysis of a distinct isolate of Bidens mottle virus infecting sunflower in Taiwan.

    Science.gov (United States)

    Liao, J Y; Hu, Chung-Chi; Chen, C C; Chang, C H; Deng, T C

    2009-01-01

    The full-length genome of a potyvirus, previously known as sunflower chlorotic spot virus isolate SF-1 (SCSV-SF-1) which causes novel symptoms on sunflowers (Helianthus annuus), was sequenced and analyzed. The genome of SCSV-SF-1 is 9,741 nucleotides long, encoding a polyprotein of 3,071 amino acids containing the consensus motifs of potyviruses. Sequence comparison revealed that the 3'-terminus of SCSV-SF-1 shared over 96% similarities with isolates of Bidens mottle virus (BiMoV). However, SCSV-SF-1 has a very narrow host range, excluding the diagnostic host species for BiMoV, Bidens pilosa and Zinnia elegans. Therefore, SCSV-SF-1 is a distinct isolate of BiMoV. This is the first report of the full-length nucleotide sequence of BiMoV infecting sunflower in Taiwan.

  11. Soft Switched Synchronous Rectifier with Phase-Shifted Full Bridge Converter and Its Small-Signal Analysis

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    By using the output inductors and body capacitances without adding any component compared with hard switching synchronous rectifier,the topology of a soft switched synchronous rectifier with phase-shifted full bridge zero voltage switching DC/DC converter is proposed. The converter efficiency is maximized due to soft switching of the full bridge MOSFETs and the synchronous MOSFETs, and also the low conduction loss of synchronous MOSFET. The operation principles of the circuit are analyzed in detail and the small-signal model is derived, also the converter dynamic characteristics are analyzed. Frequency responses of transfer functions under different values of transformer primary leakage inductance are discussed. The experimental results were obtained from a 400 V input and 100 A/12 V output DC/DC converter operating at 100 kHz. The results show that the converter efficiency is 2% higher in rated power than traditional diode rectifier.

  12. Full wave analysis of non-radiative dielectric waveguide modulator for the determination of electrical equivalent circuit

    Indian Academy of Sciences (India)

    N P Pathak; A Basu; S K Koul

    2008-07-01

    This paper reports the determination of electrical equivalent circuit of ON/OFF modulator in non-radiative dielectric (NRD) guide configurations at Ka-band. Schottky barrier mixer diode is used to realize this modulator and its characteristics are determined experimentally using vector network analyzer. Full wave FEM simulator HFSS is used to determine an equivalent circuit for the mounted diode and modulator in ON and OFF states. This equivalent circuit is used to qualitatively explain the experimental characteristics of modulator.

  13. Molecular Evolutionary Analysis of ABCB5: The Ancestral Gene Is a Full Transporter with Potentially Deleterious Single Nucleotide Polymorphisms

    OpenAIRE

    Karobi Moitra; Mark Scally; Kate McGee; Germaine Lancaster; Bert Gold; Michael Dean

    2011-01-01

    BACKGROUND: ABCB5 is a member of the ABC protein superfamily, which includes the transporters ABCB1, ABCC1 and ABCG2 responsible for causing drug resistance in cancer patients and also several other transporters that have been linked to human disease. The ABCB5 full transporter (ABCB5.ts) is expressed in human testis and its functional significance is presently unknown. Another variant of this transporter, ABCB5 beta possess a "half-transporter-like" structure and is expressed in melanoma ste...

  14. Structural analysis of the complex between calmodulin and full-length myelin basic protein, an intrinsically disordered molecule.

    Science.gov (United States)

    Majava, Viivi; Wang, Chaozhan; Myllykoski, Matti; Kangas, Salla M; Kang, Sung Ung; Hayashi, Nobuhiro; Baumgärtel, Peter; Heape, Anthony M; Lubec, Gert; Kursula, Petri

    2010-06-01

    Myelin basic protein (MBP) is present between the cytoplasmic leaflets of the compact myelin membrane in both the peripheral and central nervous systems, and characterized to be intrinsically disordered in solution. One of the best-characterized protein ligands for MBP is calmodulin (CaM), a highly acidic calcium sensor. We pulled down MBP from human brain white matter as the major calcium-dependent CaM-binding protein. We then used full-length brain MBP, and a peptide from rodent MBP, to structurally characterize the MBP-CaM complex in solution by small-angle X-ray scattering, NMR spectroscopy, synchrotron radiation circular dichroism spectroscopy, and size exclusion chromatography. We determined 3D structures for the full-length protein-protein complex at different stoichiometries and detect ligand-induced folding of MBP. We also obtained thermodynamic data for the two CaM-binding sites of MBP, indicating that CaM does not collapse upon binding to MBP, and show that CaM and MBP colocalize in myelin sheaths. In addition, we analyzed the post-translational modifications of rat brain MBP, identifying a novel MBP modification, glucosylation. Our results provide a detailed picture of the MBP-CaM interaction, including a 3D model of the complex between full-length proteins.

  15. Identification, Characterization and Full-Length Sequence Analysis of a Novel Polerovirus Associated with Wheat Leaf Yellowing Disease

    Directory of Open Access Journals (Sweden)

    Peipei Zhang

    2017-09-01

    Full Text Available To identify the pathogens responsible for leaf yellowing symptoms on wheat samples collected from Jinan, China, we tested for the presence of three known barley/wheat yellow dwarf viruses (BYDV-GAV, -PAV, WYDV-GPV (most likely pathogens using RT-PCR. A sample that tested negative for the three viruses was selected for small RNA sequencing. Twenty-five million sequences were generated, among which 5% were of viral origin. A novel polerovirus was discovered and temporarily named wheat leaf yellowing-associated virus (WLYaV. The full genome of WLYaV corresponds to 5,772 nucleotides (nt, with six AUG-initiated open reading frames, one non-AUG-initiated open reading frame, and three untranslated regions, showing typical features of the family Luteoviridae. Sequence comparison and phylogenetic analyses suggested that WLYaV had the closest relationship with sugarcane yellow leaf virus (ScYLV, but the identities of full genomic nucleotides and deduced amino acid sequence of coat protein (CP were 64.9 and 86.2%, respectively, below the species demarcation thresholds (90% in the family Luteoviridae. Furthermore, agroinoculation of Nicotiana benthamiana leaves with a cDNA clone of WLYaV caused yellowing symptoms on the plant. Our study adds a new polerovirus that is associated with wheat leaf yellowing disease, which would help to identify and control pathogens of wheat.

  16. Linkage analysis between dominant and co-dominant makers in full-sib families of out-breeding species.

    Science.gov (United States)

    Alves, Alexandre Alonso; Bhering, Leonardo Lopes; Cruz, Cosme Damião; Alfenas, Acelino Couto

    2010-07-01

    As high-throughput genomic tools, such as the DNA microarray platform, have lead to the development of novel genotyping procedures, such as Diversity Arrays Technology (DArT) and Single Nucleotide Polymorphisms (SNPs), it is likely that, in the future, high density linkage maps will be constructed from both dominant and co-dominant markers. Recently, a strictly genetic approach was described for estimating recombination frequency (r) between co-dominant markers in full-sib families. The complete set of maximum likelihood estimators for r in full-sib families was almost obtained, but unfortunately, one particular configuration involving dominant markers, segregating in a 3:1 ratio and co-dominant markers, was not considered. Here we add nine further estimators to the previously published set, thereby making it possible to cover all combinations of molecular markers with two to four alleles (without epistasis) in a full-sib family. This includes segregation in one or both parents, dominance and all linkage phase configurations.

  17. Full Wave Analysis of Passive Microwave Monolithic Integrated Circuit Devices Using a Generalized Finite Difference Time Domain (GFDTD) Algorithm

    Science.gov (United States)

    Lansing, Faiza S.; Rascoe, Daniel L.

    1993-01-01

    This paper presents a modified Finite-Difference Time-Domain (FDTD) technique using a generalized conformed orthogonal grid. The use of the Conformed Orthogonal Grid, Finite Difference Time Domain (GFDTD) enables the designer to match all the circuit dimensions, hence eliminating a major source o error in the analysis.

  18. Losses Analysis of Different Grounding Schemes for Transformer-less Wind Turbine with Full-Scale Power Converter

    DEFF Research Database (Denmark)

    Sztykiel, Michal; Teodorescu, Remus; Munk-Nielsen, Stig;

    2013-01-01

    Following work examines IGBT power loss and temperature distribution with regard to specific grounding method for the future concept of transformer-less offshore wind turbine. Analysis is performed via steady-state IGBT power loss estimator, which is made based on averaging of repetitive pulse...... cycles. Obtained results are validated with the experimental test set-up consisting of high power IGBTs....

  19. Analysis and Comparison Based on Component Stress Factor of Dual Active Bridge and Isolated Full Bridge Boost Converters for Bidirectional Fuel Cells Systems

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Mira Albert, Maria del Carmen; Zhang, Zhe;

    2014-01-01

    This paper presents an analysis and comparison of isolated topologies for bidirectional fuel cell systems. The analyzed topologies are the dua l active bridge (DAB) and the isolated full bridge boost converter (IFBBC). The analysis is performed based on the component stress factor (CSF). Results ...

  20. Spectral Mixture Analysis: Linear and Semi-parametric Full and Iterated Partial Unmixing in Multi- and Hyperspectral Image Data

    DEFF Research Database (Denmark)

    Nielsen, Allan Aasbjerg

    2001-01-01

    As a supplement or an alternative to classification of hyperspectral image data linear and semi-parametric mixture models are considered in order to obtain estimates of abundance of each class or end-member in pixels with mixed membership. Full unmixing based on both ordinary least squares (OLS......) and non-negative least squares (NNLS), and the partial unmixing methods orthogonal subspace projection (OSP), constrained energy minimization (CEM) and an eigenvalue formulation alternative are dealt with. The solution to the eigenvalue formulation alternative proves to be identical to the CEM solution...

  1. Microfluidic growth chambers with optical tweezers for full spatial single-cell control and analysis of evolving microbes.

    Science.gov (United States)

    Probst, Christopher; Grünberger, Alexander; Wiechert, Wolfgang; Kohlheyer, Dietrich

    2013-12-01

    Single-cell analysis in microfluidic systems has opened up new possibilities in biotechnological research enabling us to deal with large eukaryotic cells and even small bacteria. In particular, transient investigations in laminar flow or diffusive environments can be performed to unravel single cell behaviour. Up to now, most systems have been limited with respect to precise cell inoculation and sampling methods. Individual cell selection and manipulations have now been made possible by combining laser tweezers with microfluidic cell cultivation environments specifically tailored for micrometre-sized bacteria. Single cells were optically seeded into various micrometre-sized growth sites arranged in parallel. During cultivation, single-cell elongation, morphology and growth rates were derived from single cells and microcolonies of up to 500 cells. Growth of irradiated bacteria was not impaired by minimizing the exposed laser dosage as confirmed by exceptional growth rates. In fact, Escherichia coli exhibited doubling times of less than 20min. For the first time, a filamentous Escherichia coli WT (MG1655) was safely relocated from its growing microcolony by laser manipulations. The cell was transferred to an empty cultivation spot allowing single-cell growth and morphology investigations. Contrary to previous discussions, the filamentous E. coli exhibited normal cell morphology and division after a few generations. This combination of optical tweezers and single-cell analysis in microfluidics adds a new degree of freedom to microbial single-cell analysis. © 2013.

  2. Cloning and Analysis of Full-Length cDNA of PumNPR1 Gene from Pyrus ussuriensis Maxim

    Institute of Scientific and Technical Information of China (English)

    CHE Daidi; FAN Jinping; WANG Jingang; XU Ping; YANG Tao; LIU Shenkui

    2008-01-01

    The purpose of this study is to find a new gene resource for the researches of molecular breeding of Rosaceae plants disease-resistance. Pyrus ussuriensis Maxim is used as a starting material to clone the full-length cDNA of NPR1(nonexpressor of pathogenesis- related genes 1) which is a key regulator in SA (salicylic acid)-mediated systemic acquired resistance (SAR) by homologous cloning and RACE techniques. The length of the cDNA sequence was 1 767 bp, the ORF was 1 761 bp, it coded 586 amino acids, pI=5.58, the relative molecular weight was 65.009 ku, contained 19 kinds of amino acids, and had full BTB/POZ and ANK domains. Compared the homology of NPR1 gene in GenBank database, the homology with Pyrus pyrifolia, Arabidopsis thaliana, Nicotiana tabacum, Lycopersicon esculentum, Oryza sativa, Helianthus annuus were 98%, 62%, 68%, 65%, 57%, 63%. The homology of functional area were 99%, 78%, 82%, 79%, 74%, 77%. This NPR1 gene was considered as homologic gene of Pyrus ussuriensis Maxim and named PumNPR1.

  3. Computational Analysis of Intra-Ventricular Flow Pattern Under Partial and Full Support of BJUT-II VAD

    Science.gov (United States)

    Zhang, Qi; Gao, Bin; Chang, Yu

    2017-01-01

    Background Partial support, as a novel support mode, has been widely applied in clinical practice and widely studied. However, the precise mechanism of partial support of LVAD in the intra-ventricular flow pattern is unclear. Material/Methods In this study, a patient-specific left ventricular geometric model was reconstructed based on CT data. The intra-ventricular flow pattern under 3 simulated conditions – “heart failure”, “partial support”, and “full support” – were simulated by using fluid-structure interaction (FSI). The blood flow pattern, wall shear stress (WSS), time-average wall shear stress (TAWSS), oscillatory shear index (OSI), and relative residence time (RRT) were calculated to evaluate the hemodynamic effects. Results The results demonstrate that the intra-ventricular flow pattern is significantly changed by the support level of BJUT-II VAD. The intra-ventricular vortex was enhanced under partial support and was eliminated under full support, and the high OSI and RRT regions changed from the septum wall to the cardiac apex. Conclusions In brief, the support level of the BJUT-II VAD has significant effects on the intra-ventricular flow pattern. The partial support mode of BJUT-II VAD can enhance the intra-ventricular vortex, while the distribution of high OSI and RRT moved from the septum wall to the cardiac apex. Hence, the partial support mode of BJUT-II VAD can provide more benefit for intra-ventricular flow pattern. PMID:28239142

  4. Computational Analysis of Intra-Ventricular Flow Pattern Under Partial and Full Support of BJUT-II VAD.

    Science.gov (United States)

    Zhang, Qi; Gao, Bin; Chang, Yu

    2017-02-27

    BACKGROUND Partial support, as a novel support mode, has been widely applied in clinical practice and widely studied. However, the precise mechanism of partial support of LVAD in the intra-ventricular flow pattern is unclear. MATERIAL AND METHODS In this study, a patient-specific left ventricular geometric model was reconstructed based on CT data. The intra-ventricular flow pattern under 3 simulated conditions - "heart failure", "partial support", and "full support" - were simulated by using fluid-structure interaction (FSI). The blood flow pattern, wall shear stress (WSS), time-average wall shear stress (TAWSS), oscillatory shear index (OSI), and relative residence time (RRT) were calculated to evaluate the hemodynamic effects. RESULTS The results demonstrate that the intra-ventricular flow pattern is significantly changed by the support level of BJUT-II VAD. The intra-ventricular vortex was enhanced under partial support and was eliminated under full support, and the high OSI and RRT regions changed from the septum wall to the cardiac apex. CONCLUSIONS In brief, the support level of the BJUT-II VAD has significant effects on the intra-ventricular flow pattern. The partial support mode of BJUT-II VAD can enhance the intra-ventricular vortex, while the distribution of high OSI and RRT moved from the septum wall to the cardiac apex. Hence, the partial support mode of BJUT-II VAD can provide more benefit for intra-ventricular flow pattern.

  5. Full genome sequence analysis of a novel adenovirus of rhesus macaque origin indicates a new simian adenovirus type and species

    Directory of Open Access Journals (Sweden)

    Daniel Malouli

    2014-09-01

    Full Text Available Multiple novel simian adenoviruses have been isolated over the past years and their potential to cross the species barrier and infect the human population is an ever present threat. Here we describe the isolation and full genome sequencing of a novel simian adenovirus (SAdV isolated from the urine of two independent, never co-housed, late stage simian immunodeficiency virus (SIV-infected rhesus macaques. The viral genome sequences revealed a novel type with a unique genome length, GC content, E3 region and DNA polymerase amino acid sequence that is sufficiently distinct from all currently known human- or simian adenovirus species to warrant classifying these isolates as a novel species of simian adenovirus. This new species, termed Simian mastadenovirus D (SAdV-D, displays the standard genome organization for the genus Mastadenovirus containing only one copy of the fiber gene which sets it apart from the old world monkey adenovirus species HAdV-G, SAdV-B and SAdV-C.

  6. System-Integrated Finite Element Analysis of a Full-Scale Helicopter Crash Test with Deployable Energy Absorbers

    Science.gov (United States)

    Annett, Martin S.; Polanco, Michael A.

    2010-01-01

    A full-scale crash test of an MD-500 helicopter was conducted in December 2009 at NASA Langley's Landing and Impact Research facility (LandIR). The MD-500 helicopter was fitted with a composite honeycomb Deployable Energy Absorber (DEA) and tested under vertical and horizontal impact velocities of 26-ft/sec and 40-ft/sec, respectively. The objectives of the test were to evaluate the performance of the DEA concept under realistic crash conditions and to generate test data for validation of a system integrated finite element model. In preparation for the full-scale crash test, a series of sub-scale and MD-500 mass simulator tests was conducted to evaluate the impact performances of various components, including a new crush tube and the DEA blocks. Parameters defined within the system integrated finite element model were determined from these tests. The objective of this paper is to summarize the finite element models developed and analyses performed, beginning with pre-test predictions and continuing through post-test validation.

  7. Charged Higgs Boson Production at e+e- Colliders in the Complex MSSM: A Full One-Loop Analysis

    CERN Document Server

    Heinemeyer, S

    2016-01-01

    For the search for additional Higgs bosons in the Minimal Supersymmetric Standard Model (MSSM) as well as for future precision analyses in the Higgs sector precise knowledge of their production properties is mandatory. We evaluate the cross sections for the charged Higgs boson production at e+e- colliders in the MSSM with complex parameters (cMSSM). The evaluation is based on a full one-loop calculation of the production mechanism e+e- -> H+H- and e+e- -> H^\\pm W^\\mp, including soft and hard QED radiation. The dependence of the Higgs boson production cross sections on the relevant cMSSM parameters is analyzed numerically. We find sizable contributions to many cross sections. They are, depending on the production channel, roughly of 5-10% of the tree-level results, but can go up to 20% or higher. The full one-loop contributions are important for a future linear e+e- collider such as the ILC or CLIC.

  8. Mitigation of self-excited oscillations at full load: CFD analysis of air admission and effects of runner design

    Science.gov (United States)

    Chirkov, D.; Scherbakov, P.; Cherny, S.; Zakharov, A.; Skorospelov, V.; Turuk, P.

    2016-11-01

    In full and over load operating points some Francis turbines experience strong selfexcited pressure and power oscillations, which restrict the range of operation and maximum output of the turbine. Previously the authors proposed a 1D-3D two-phase model and numerical method for investigation of this phenomenon. In the present paper this model is further extended and applied to investigation of countermeasures, used for prevention of high load oscillations. First, the third phase - non-condensable air - is introduced into the model in order to investigate the effect of air admission. Then, several modifications of runner cone are examined, showing negligible effect on the amplitude and frequency of full load oscillations. Next, different modifications of runner blade shape are considered, giving different axial and circumferential velocity profiles downstream the runner. It is shown that variation of blade shape significantly affects the onset and intensity of self-excited oscillations. The obtained results indicate that proper runner design is able to eliminate high load instability without the need of air admission and reduction in turbine efficiency.

  9. Numerical simulations of full-wave fields and analysis of channel wave characteristics in 3-D coal mine roadway models

    Science.gov (United States)

    Yang, Si-Tong; Wei, Jiu-Chuan; Cheng, Jiu-Long; Shi, Long-Qing; Wen, Zhi-Jie

    2016-12-01

    Currently, numerical simulations of seismic channel waves for the advance detection of geological structures in coal mine roadways focus mainly on modeling twodimensional wave fields and therefore cannot accurately simulate three-dimensional (3-D) full-wave fields or seismic records in a full-space observation system. In this study, we use the first-order velocity-stress staggered-grid finite difference algorithm to simulate 3-D full-wave fields with P-wave sources in front of coal mine roadways. We determine the three components of velocity V x, V y, and V z for the same node in 3-D staggered-grid finite difference models by calculating the average value of V y, and V z of the nodes around the same node. We ascertain the wave patterns and their propagation characteristics in both symmetrical and asymmetric coal mine roadway models. Our simulation results indicate that the Rayleigh channel wave is stronger than the Love channel wave in front of the roadway face. The reflected Rayleigh waves from the roadway face are concentrated in the coal seam, release less energy to the roof and floor, and propagate for a longer distance. There are surface waves and refraction head waves around the roadway. In the seismic records, the Rayleigh wave energy is stronger than that of the Love channel wave along coal walls of the roadway, and the interference of the head waves and surface waves with the Rayleigh channel wave is weaker than with the Love channel wave. It is thus difficult to identify the Love channel wave in the seismic records. Increasing the depth of the receivers in the coal walls can effectively weaken the interference of surface waves with the Rayleigh channel wave, but cannot weaken the interference of surface waves with the Love channel wave. Our research results also suggest that the Love channel wave, which is often used to detect geological structures in coal mine stopes, is not suitable for detecting geological structures in front of coal mine roadways

  10. Integrated Analysis of Environment, Cattle and Human Serological Data: Risks and Mechanisms of Transmission of Rift Valley Fever in Madagascar.

    Directory of Open Access Journals (Sweden)

    Marie-Marie Olive

    2016-07-01

    Full Text Available Rift Valley fever (RVF is a vector-borne disease affecting ruminants and humans. Madagascar was heavily affected by RVF in 2008-2009, with evidence of a large and heterogeneous spread of the disease. The identification of at-risk environments is essential to optimize the available resources by targeting RVF surveillance in Madagascar. Herein, the objectives of our study were: (i to identify the environmental factors and areas favorable to RVF transmission to both cattle and human and (ii to identify human behaviors favoring human infections in Malagasy contexts.First, we characterized the environments of Malagasy communes using a Multiple Factor Analysis (MFA. Then, we analyzed cattle and human serological data collected at national level using Generalized Linear Mixed Models, with the individual serological status (cattle or human as the response, and MFA factors, as well as other potential risk factors (cattle density, human behavior as explanatory variables. Cattle and human seroprevalence rates were positively associated to humid environments (p<0.001. Areas with high cattle density were at risk (p<0.01; OR = 2.6. Furthermore, our analysis showed that frequent contact with raw milk contributed to explain human infection (OR = 1.6. Finally, our study highlighted the eastern-coast, western and north-western parts as high-risk areas for RVF transmission in cattle.Our integrated approach analyzing environmental, cattle and human datasets allow us to bring new insight on RVF transmission patterns in Madagascar. The association between cattle seroprevalence, humid environments and high cattle density suggests that concomitant vectorial and direct transmissions are critical to maintain RVF enzootic transmission. Additionally, in the at-risk humid environment of the western, north-western and the eastern-coast areas, suitable to Culex and Anopheles mosquitoes, vectorial transmission probably occurs in both cattle and human. The relative contribution

  11. Full-Wave Analysis of Traveling-Wave Field-Effect Transistors Using Finite-Difference Time-Domain Method

    Directory of Open Access Journals (Sweden)

    Koichi Narahara

    2012-01-01

    Full Text Available Nonlinear transmission lines, which define transmission lines periodically loaded with nonlinear devices such as varactors, diodes, and transistors, are modeled in the framework of finite-difference time-domain (FDTD method. Originally, some root-finding routine is needed to evaluate the contributions of nonlinear device currents appropriately to the temporally advanced electrical fields. Arbitrary nonlinear transmission lines contain large amount of nonlinear devices; therefore, it costs too much time to complete calculations. To reduce the calculation time, we recently developed a simple model of diodes to eliminate root-finding routines in an FDTD solver. Approximating the diode current-voltage relation by a piecewise-linear function, an extended Ampere's law is solved in a closed form for the time-advanced electrical fields. In this paper, we newly develop an FDTD model of field-effect transistors (FETs, together with several numerical examples that demonstrate pulse-shortening phenomena in a traveling-wave FET.

  12. Analysis of multiple recording methods for full resolution multi-view autostereoscopic 3D display system incorporating VHOE

    Science.gov (United States)

    Hwang, Yong Seok; Cho, Kyu Ha; Kim, Eun Soo

    2014-03-01

    In this paper, we propose multiple recording process of photopolymer for a full-color multi-view including multiple-view auto-stereoscopic 3D display system based on VHOE (Volume Holographic Optical Element). To overcome the problems such as low resolution, and limited viewing zone of conventional 3D-display without glasses, we designed multiple recording condition of VHOE for multi-view display. It is verified that VHOE may be optically made by angle-multiplexed recording of pre-designed multiple-viewing zone that uniformly is recorded through optimized exposuretime scheduling scheme. Here, VHOE-based backlight system for 4-view stereoscopic display is implemented, in which the output beams that playing a role reference beam from LGP(Light guide plate)t may be sequentially synchronized with the respective stereo images displayed on the LCD panel.

  13. Functionality of the approach of hierarchical analysis in the full cost accounting in the IRP of a metropolitan airport

    Energy Technology Data Exchange (ETDEWEB)

    Cicone, Decio Jr. [GEPEA-USP, Grupo de Energia do Departamento de Engenharia de Energia e Automacao Eletricas, Escola Politecnica da Universidade de Sao Paulo (Brazil); Udaeta, Miguel Edgar Morales; Grimoni, Jose Aquiles Baesso; Galvao, Luiz Claudio Ribeiro [IEE/USP, Instituto de Eletrotecnica e Energia, Universidade de Sao Paulo (Brazil)

    2008-03-15

    This work shows the application of the analytic hierarchy process (AHP) in the full cost accounting (FCA) within the integrated resource planning (IRP) process. For this purpose, a pioneer case was developed and different energy solutions of supply and demand for a metropolitan airport (Congonhas) were considered [Moreira, E.M., 2005. Modelamento energetico para o desenvolvimento limpo de aeroporto metropolitano baseado na filosofia do PIR - O caso da metropole de Sao Paulo. Dissertacao de mestrado, GEPEA/USP]. These solutions were compared and analyzed utilizing the software solution ''Decision Lens'' that implements the AHP. The final part of this work has a classification of resources that can be considered to be the initial target as energy resources, thus facilitating the restraints of the IRP of the airport and setting parameters aiming at sustainable development. (author)

  14. Spectral Mixture Analysis: Linear and Semi-parametric Full and Iterated Partial Unmixing in Multi- and Hyperspectral Image Data

    DEFF Research Database (Denmark)

    Nielsen, Allan Aasbjerg

    2001-01-01

    to suggest an iterated CEM scheme. Also the target constrained interference minimized filter (TCIMF) is described. Spectral angle mapping (SAM) is briefly described. Finally, semi-parametric unmixing (SPU) based on a combined linear and additive model with a non-linear, smooth function to represent end......As a supplement or an alternative to classification of hyperspectral image data linear and semi-parametric mixture models are considered in order to obtain estimates of abundance of each class or end-member in pixels with mixed membership. Full unmixing based on both ordinary least squares (OLS......) and non-negative least squares (NNLS), and the partial unmixing methods orthogonal subspace projection (OSP), constrained energy minimization (CEM) and an eigenvalue formulation alternative are dealt with. The solution to the eigenvalue formulation alternative proves to be identical to the CEM solution...

  15. Full-Depth Pavement Reclamation with Foamed Asphalt: First-Level Analysis Report on HVS Testing on State Route 89

    OpenAIRE

    Theyse, Hecter; Long, Fenella; Jones, David; Harvey, John T

    2006-01-01

    This report focuses on the HVS testing of a foamed asphalt treated, reclaimed asphalt pavement (RAP) on State Route 89 near Sierraville. The report discusses the expected behavior of the HVS test sections, presents the results from field surveys done during June 2003, October 2003 and May 2004 as well as the 1st level analysis of HVS results from the test site. Results from field surveys done prior to, during and after HVS testing show that the pavement structure of the HVS test sections on S...

  16. Full Mouth Rehabilitation by Minimally Invasive Cosmetic Dentistry Coupled with Computer Guided Occlusal Analysis: A Case Report.

    Science.gov (United States)

    Sarita; Thumati, Prafulla

    2014-12-01

    Evidence of dentistry dates back to 7000 B.C. and since then has come, indeed a long sophisticated way in treatment management of our dental patients. There have been admirable advances in the field of prosthodontics by the way of techniques and materials; enabling production of artificial teeth that feel, function and appear nothing but natural. The following case report describes the management of maxillary edentulousness with removable complete denture and mandibular attrition and missing teeth with onlays and FPD by the concept of minimally invasive cosmetic dentistry. Computer guided occlusal analysis was used to guide sequential occlusal adjustments to obtain measurable bilateral occlusal contacts simultaneously.

  17. Analysis of Nb3Sn Strand Microstructure After Full-size SULTAN Test of ITER TF Conductor Sample

    Science.gov (United States)

    Kaverin, D.; Potanina, L.; Shutov, K.; Vysotsky, V.; Tronza, V.; Mitin, A.; Abdyukhanov, I.; Alekseev, M.

    The study of defects generated in superconducting filaments of Nb3Sn strands under electromagnetic and thermal cycling was carried out for the TFRF3 cable-in-conduit-conductor (CICC) sample that passed final testing inthe SULTAN test facility. The TFRF3 sample was manufactured forthe qualification of the RF Toroidal Field (TF) CICC. The strand samples were taken from different locations in the cross-section of TFRF3 and different positions along its axis in relation to background magnetic field. Qualitative and quantitative analysis of defects were carried out using metallographic analysis of images obtained by Laser Scanning Microscope. We analyzed number, type, and distribution of defects in filaments of the Nb3Sn strand samples extracted from different petals of TFRF3 in dependence on thestrand location in the cross-section (the center of petal, nearby the spiral, nearby the outer jacket) in the high field zone (HFZ). The results about the defects amount and their distribution are presented and discussed.

  18. A Type System for the Vectorial Aspect of the Linear-Algebraic Lambda-Calculus

    Directory of Open Access Journals (Sweden)

    Pablo Arrighi

    2012-07-01

    Full Text Available We describe a type system for the linear-algebraic lambda-calculus. The type system accounts for the part of the language emulating linear operators and vectors, i.e. it is able to statically describe the linear combinations of terms resulting from the reduction of programs. This gives rise to an original type theory where types, in the same way as terms, can be superposed into linear combinations. We show that the resulting typed lambda-calculus is strongly normalizing and features a weak subject-reduction.

  19. Stability analysis of non-axisymmetric three-dimensional finite element rotor models with partial and full mass lumping

    Indian Academy of Sciences (India)

    Smitadhi Ganguly; A Nandi; S Neogy

    2014-06-01

    Unlike structural dynamics, the three-dimensional finite-element model of non-axisymmetric rotors on orthotropic bearings generates a large gyroscopic system with parametric stiffness. The present work explores the use of mass-lumping in stability analysis of such systems. Using a variant of Hill’s method, the problem reduces to a generalized Eigen value problem of order $nm \\times nm$, with as the order of the system in state vector representation and as the number of terms in the assumed solution. The matrices in both the sides of the Eigen value problem are expressed in terms of Kronecker products where the mass-matrix appears twice as a sub-matrix in both the sides of the equation. A particular one or both of them can be made diagonal. Both options produce sufficiently accurate results with considerable savings, even with a coarse mesh.

  20. Towards a full implementation of a robust solution of a domain specific visual query language for HEP physics analysis

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, V; Conde, P [LIP, Lisbon (Portugal); Amaral, V, E-mail: vasco.sousa@gmail.com, E-mail: vasco.amaral@di.fct.unl.pt, E-mail: Patricia.Conde.Muino@cern.ch

    2008-07-15

    In our previous work, project PHEASANT, we have proposed a Domain Specific Language (DSL) to provide the HEP community with a tool that could increase user's productivity. This tool would tackle the problem while producing query code for HEP physics data analysis. The first step of this project was to design and implement a solution that would be a proof of concept. We are now concentrated on implementation issues in order to deploy a final tool (i.e. consistent, robust, etc). The concept of domain specific languages has always been implicit in Software Engineering projects although the development of such languages was never done in a very systematic way. The main goal of having DSLs is to rise the level of abstraction. The idea is to provide the final user (stakeholder) with tools to reason and model the solution by using concepts of the problem domain instead of having to reason with concepts of the problem domain (meaning the implementation details like programming concepts and hardware restrictions). Once we have the model specified, we can use Model Driven Development and Software Product Lines techniques to deploy artifacts in a automatic way (meaning: software products, code, documentation etc). The Software Engineering community has been focusing lately its attention to methodologies and tool deployment in order to help DSL developers in their effort to help productivity and efficency at several application domains such as HEP. A comparative study of these tools should be done to determine their capability to answer the specificity of HEP Physics Analysis requirements. In this communication we will present the several technologies for DSLs meta-modeling studied in order to implement the DSL proposed by the PHEASANT project.

  1. Analysis and design of coaxial three-mirror anastigmat with long effective focal length and full two-dimensional field

    Science.gov (United States)

    Lin, Han; Baoqi, Mao; Wen, Sun; Weimin, Shen

    2016-10-01

    There is a race to develop spaceborne high-resolution video cameras since Skybox's success. For low manufacture cost and adaption to micro and small satellites, it is urgent to design and develop compact long focal length optical system with not only small volume, light weight and easy implementation, and also two dimensional field. Our focus is on the Coaxial Three-Mirror Anastigmat (CTMA) with intermediate real image for its no need outer hood and compactness and for its easy alignment, low-order aspheric surface and low cost. The means to deflect its image space beam for accessibility of focal plane array detector and to eliminate its inherent secondary obscuration from its primary mirror central hole and deflection flat mirror is discussed. The conditions to satisfy the above-mentioned requirements are presented with our derived relationship among its optical and structural parameters based on Gaussian optics and geometry. One flat mirror near its exit pupil can be used to deflect its image plane from its axis. And its total length can be decreased with other some flat mirrors. Method for determination of its initial structure with the derived formulae is described through one design example. Furthermore, optimized CTMA without secondary obscuration and with effective focal length (EFFL) of 10m is reported. Its full field, F-number and total length are respectively 1.1°×1°, F/14.3, and one eighth of its EFFL. And its imaging quality is near diffraction limit.

  2. A spoon full of studies helps the comparison go down: A comparative analysis of Tulving’s spoon test

    Directory of Open Access Journals (Sweden)

    Damian eScarf

    2014-08-01

    Full Text Available Mental time travel refers to the ability to cast one’s mind back in time to re-experience a past event and forward in time to pre-experience events that may occur in the future. Endel Tulving (2005, an authority on mental time travel, holds that this ability is unique to humans. Anticipating that comparative psychologists would challenge this claim, Tulving (2005 proposed his spoon test, a test specifically designed to assess whether nonhuman animals are capable of mental time travel. A number of studies have now employed the spoon test to assess mental time travel in nonhuman animals. Here, we review the evidence for mental time travel in primates. To provide a benchmark, we also review studies that have employed the spoon test with preschool children. The review demonstrates that if we compare the performance of great apes to that of preschool children, and hold them to the same criteria, the data suggest mental travel is present but not ubiquitous in great apes.

  3. Ecological aspects of the vectorial control of Chagas' disease in Brazil Aspectos ecológicos do controle de vetores para doença de Chagas no Brasil

    Directory of Open Access Journals (Sweden)

    João Carlos P. Dias

    Full Text Available The feasibility and most important ecological aspects of vectorial Chagas' disease control are discussed. The spread and maintenance of this disease involve multiple ecological and sociopolitical factors that must be taken into account when control programs are planned, executed and evaluated. In spite of its complexity, Chagas disease can be controlled using methods that target specific mechanisms of transmission, the most important being vectorial and transfusional. Major ecological problems in Chagas' disease control do not exist, even in the case of the chemical control of triatomine vectors. The main challenges for the Brazilian Control Program at this moment are: its maintenance as a political priority; the threat of peridomestic vectors; and the consolidation of permanent horizontal and participative epidemiological surveillance systems against the vector.A importância da doença de Chagas e de seu controle é assinalada para o Brasil e demais países endêmicos da América Latina, enfatizando-se os aspectos ecológicos envolvidos. Os principais insumos e estratégias de combate à doença humana já existem e estão disponíveis, devendo-se priorizar o controle dos vetores domiciliados e das transfusões de sangue. Os programas de controle devem levar em conta os elementos ecológicos e sociais pertinentes, inclusive para se prevenir novas situações epidemiológicas no futuro. Não se assinalam problemas ecológicos de importância quando os programas de controle são planejados e executados com racionalidade. Os maiores desafios ao programa brasileiro, são hoje, a manutenção de sua continuidade a nível nacional, o controle de vetores secundários no peridomicílio e a consolidação de uma vigilância epidemiológica horizontalizada e participativa.

  4. Fundamental Research on Percussion Drilling: Improved rock mechanics analysis, advanced simulation technology, and full-scale laboratory investigations

    Energy Technology Data Exchange (ETDEWEB)

    Michael S. Bruno

    2005-12-31

    This report summarizes the research efforts on the DOE supported research project Percussion Drilling (DE-FC26-03NT41999), which is to significantly advance the fundamental understandings of the physical mechanisms involved in combined percussion and rotary drilling, and thereby facilitate more efficient and lower cost drilling and exploration of hard-rock reservoirs. The project has been divided into multiple tasks: literature reviews, analytical and numerical modeling, full scale laboratory testing and model validation, and final report delivery. Literature reviews document the history, pros and cons, and rock failure physics of percussion drilling in oil and gas industries. Based on the current understandings, a conceptual drilling model is proposed for modeling efforts. Both analytical and numerical approaches are deployed to investigate drilling processes such as drillbit penetration with compression, rotation and percussion, rock response with stress propagation, damage accumulation and failure, and debris transportation inside the annulus after disintegrated from rock. For rock mechanics modeling, a dynamic numerical tool has been developed to describe rock damage and failure, including rock crushing by compressive bit load, rock fracturing by both shearing and tensile forces, and rock weakening by repetitive compression-tension loading. Besides multiple failure criteria, the tool also includes a damping algorithm to dissipate oscillation energy and a fatigue/damage algorithm to update rock properties during each impact. From the model, Rate of Penetration (ROP) and rock failure history can be estimated. For cuttings transport in annulus, a 3D numerical particle flowing model has been developed with aid of analytical approaches. The tool can simulate cuttings movement at particle scale under laminar or turbulent fluid flow conditions and evaluate the efficiency of cutting removal. To calibrate the modeling efforts, a series of full-scale fluid hammer

  5. Full-length genome sequence analysis of four subgroup J avian leukosis virus strains isolated from chickens with clinical hemangioma.

    Science.gov (United States)

    Lin, Lulu; Wang, Peikun; Yang, Yongli; Li, Haijuan; Huang, Teng; Wei, Ping

    2017-07-17

    Since 2014, cases of hemangioma associated with avian leukosis virus subgroup J (ALV-J) have been emerging in commercial chickens in Guangxi. In this study, four strains of the subgroup J avian leukosis virus (ALV-J), named GX14HG01, GX14HG04, GX14LT07, and GX14ZS14, were isolated from chickens with clinical hemangioma in 2014 by DF-1 cell culture and then identified with ELISA detection of ALV group specific antigen p27, the detection of subtype specific PCR and indirect immunofluorescence assay (IFA) with ALV-J specific monoclonal antibody. The complete genomes of the isolates were sequenced and it was found that the gag and pol were relatively conservative, while env was variable especially the gp85 gene. Homology analysis of the env gene sequences showed that the env gene of all the four isolates had higher similarities with the hemangioma (HE)-type reference strains than that of the myeloid leukosis (ML)-type strains, and moreover, the HE-type strains' specific deletion of 205-bp sequence covering the rTM and DR1 in 3'UTR fragment was also found in the four isolates. Further analysis on the sequences of subunits of env gene revealed an interesting finding: the gp85 of isolates GX14ZS14 and GX14HG04 had a higher similarity with HPRS-103 and much lower similarity with the HE-type reference strains resulting in GX14ZS14, GX14HG04, and HPRS-103 being clustered in the same branch, while gp37 had higher similarities with the HE-type reference strains when compared to that of HPRS-103, resulted in GX14ZS14, GX14HG04, and HE-type reference strains being clustered in the same branch. The results suggested that isolates GX14ZS14 and GX14HG04 may be the recombinant strains of the foreign strain HPRS-103 with the local epidemic HE-type strains of ALV-J.

  6. Long-term performance and fouling analysis of full-scale direct nanofiltration (NF) installations treating anoxic groundwater

    KAUST Repository

    Beyer, Florian

    2014-10-01

    Long-term performance and fouling behavior of four full-scale nanofiltration (NF) plants, treating anoxic groundwater at 80% recovery for drinking water production, were characterized and compared with oxic NF and reverse osmosis systems. Plant operating times varied between 6 and 10 years and pretreatment was limited to 10μm pore size cartridge filtration and antiscalant dosage (2-2.5mgL-1) only. Membrane performance parameters normalized pressure drop (NPD), normalized specific water permeability (Kw) and salt retention generally were found stable over extended periods of operation (>6 months). Standard acid-base cleanings (once per year or less) were found to be sufficient to maintain satisfying operation during direct NF of the described iron rich (≤8.4mgL-1) anoxic groundwaters. Extensive autopsies of eight NF membrane elements, which had been in service since the plant startup (6-10 years), were performed to characterize and quantify the material accumulated in the membrane elements. Investigations using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), total organic carbon (TOC) and adenosine triphosphate (ATP) measurements revealed a complex mixture of organic, biological and inorganic materials. The fouling layers that developed during half to one year of operation without chemical cleaning were very thin (<2. μm). Most bio(organic) accumulates were found in the lead elements of the installations while inorganic precipitates/deposits (aluminosilicates and iron(II)sulfides) were found in all autopsied membrane elements. The high solubility of reduced metal ions and the very slow biofilm development under anoxic conditions prevented rapid fouling during direct NF of the studied groundwaters. When compared to oxic NF and RO systems in general (e.g. aerated ground waters or surface waters), the operation and performance of the described anoxic installations (with minimal pretreatment) can be described as very stable. © 2014

  7. Systematic analysis of microfauna indicator values for treatment performance in a full-scale municipal wastewater treatment plant.

    Science.gov (United States)

    Hu, Bo; Qi, Rong; Yang, Min

    2013-07-01

    The indicator values of microfauna functional groups and species for treatment performance were systematically evaluated based on the continuous monitoring of the entire microfauna communities including both protozoa and metazoa over a period of 14 months, in two parallel full-scale municipal wastewater treatment systems in a plant in Beijing, China. A total of 57 species of ciliates, 14 species (units) of amoebae, 14 species (units) of flagellates and 4 classes of small metazoa were identified, with Arcella hemisphaerica, Vorticella striata, Vorticella convallaria, Epistylis plicatilis and small flagellates (e.g. Bodo spp.) as the dominant protozoa, and rotifers as the dominant metazoa. The abundance of the sessile ciliates was correlated with the removals of BOD5 (Pearson's r = 0.410, p < 0.05) and CODcr (r = 0.397, p < 0.05) while the testate amoebae was significantly positively related to nitrification (r = 0.523, p < 0.01). At the same time, some other associations were also identified: the abundances of the large flagellates (r = 0.447, p < 0.01), the metazoa (r = 0.718, p < 0.01) and species Aspidisca sulcata (r = 0.337, p < 0.05) were positively related to nitrification; the abundance of Aspidisca costata was correlated to the TN (total nitrogen) removal (r = -0.374, p < 0.05 ); the abundances of the sessile species Carchesium polypinum (r = 0.458, p < 0.01) and E. plicatilis (r = 0.377, p < 0.05) were correlated with the removal of suspended solids.

  8. Evaluation of the Heading Confinement Pressure Effect on Ground Settlement for EPBTBM Using Full 3D Numerical Analysis

    Directory of Open Access Journals (Sweden)

    Amir Hossein Haghi

    2013-06-01

    Full Text Available Ground settlement is often the most serious concern when tunneling under an old city with numerous historic monuments. A successful engineering design under these conditions would require getting the most out of the ground strength parameters and avoiding any weakening maneuver throughout the operation. Knowing that surface settlement is highly affected by tunneling parameters in EPB shield tunneling lead us to estimate the optimum values for the machine heading pressure with the lower amount of the ground settlement in fragile structure of the old city for the Esfahan Subway Project. Tunnels were dug underneath some of the most prominent historical sites along the path of the project. To improve precision and efficiency in tunneling operation, at the first step, tunnel heading confinement pressure is calculated by using an advanced 3D mathematical approach based on the limit equilibrium theory. Then, a promoted 3D finite element model is developed, taking into account the tunneling procedures and the designed heading confinement pressure from the first step. Settlements were pre-calculated and the surface displacement was checked at all sensitive locations. At the third step, settlement is estimated by exerting executed face supporting pressure to the tunnel face and the concluded amounts for displacement are compared with the outputs of extensometers. This comparison leads us to check the reliability of calculated settlements and the accuracy of the designed tunnel heading confinement pressure. Furthermore, evaluating the relation between extensometer outputs and executed tunnel face pressure at the points of extensometers stations validates the assumption that the safe face supporting pressure causes least surface displacement. Although the minimum pressure occurred in short term fluctuations, this approach confirms the sensibility of settlement with the least executed face supporting pressure.. It is also found that higher executed face

  9. Immunohistochemical and morphometric analysis of intestinal full-thickness biopsy samples from cats with lymphoplasmacytic inflammatory bowel disease.

    Science.gov (United States)

    Marsilio, S; Kleinschmidt, S; Nolte, I; Hewicker-Trautwein, M

    2014-05-01

    The distribution and numbers of CD3(+) T lymphocytes, immunoglobulin(+) plasma cells and calprotectin (L1)(+) macrophages was analyzed in full-thickness, formalin-fixed biopsy samples from the small intestine (duodenum, jejunum and ileum) and from the colon from nine cats with clinical signs of inflammatory bowel disease (IBD). All animals had lymphoplasmacytic enteritis or lymphoplasmacytic enterocolitis. Equivalent samples from the same intestinal regions from 12 healthy pet cats served as controls. Labelled cells in the lamina propria were counted by computer-aided morphometry. The different cell types were similarly distributed in both groups, but there were differences in their numbers. There were more CD3(+) T cells in the duodenum and jejunum of cats with IBD; however, the difference was only significant for the duodenum. There were significantly more IgA(+) cells in the duodenal crypt region. There were significantly more IgG(+) cells in the lower jejunal crypt region. Plasma cells expressing IgM were decreased in cats with IBD, but the difference was not significant. L1(+) macrophages were significantly decreased in the lower crypt area of the colon in cats with IBD and there was a trend to decreased L1(+) cells in the upper crypt area of the duodenum and jejunum. Comparison of the results of this study with previous findings on endoscopically-obtained duodenal biopsy samples from cats with IBD revealed some differences. These discrepancies might relate to differences between control cat populations, types of biopsy samples, methodological factors such as different counting techniques and the activity of the disease at the time of sampling.

  10. Full report of laser doppler velocimetry (Het-V) data, results , and analysis for pRad shot 0632

    Energy Technology Data Exchange (ETDEWEB)

    Tupa, Dale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tainter, Amy Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-21

    This was a collaborative shot with AWE investigators Paul Willis-Patel, David Bell, Seth Grant, David Tarr, and James Richley. The shot was assembled in Los Alamos, after which David Bell set up the probe holder and finalized the alignment. The probe holder location and configuration was modified from previous years to make room for the laser illuminated visible imaging diagnostic. The LANL pRad PDV team was Dale Tupa, Amy Tainter, and Patrick Medina. This shot had three PDV probes: one aimed at the center, one aimed at a feature, one aimed at the reverse side of the shot. The shot also had 9 points of a spectroscopy diagnostic. The pRad team helped set up and field the spectroscopy, but did not help with any data analysis. (The support documentation for the PDV results includes a timing map for the spectroscopy.) Please direct questions on the velocimetry to Dale Tupa or Amy Tainter. The shot radiographs were classified, but the data from the optical diagnostics are not.

  11. Removal performance and water quality analysis of paper machine white water in a full-scale wastewater treatment plant.

    Science.gov (United States)

    Shi, Shuai; Wang, Can; Fang, Shuai; Jia, Minghao; Li, Xiaoguang

    2016-09-29

    Paper machine white water is generally characterized as a high concentration of suspended solids and organic matters. A combined physicochemical-biological and filtration process was used in the study for removing pollutants in the wastewater. The removal efficiency of the pollutant in physicochemical and biological process was evaluated, respectively. Furthermore, advanced technology was used to analyse the water quality before and after the process treatment. Experimental results showed that the removal efficiency of suspend solids (SS) of the system was above 99%, while the physicochemical treatment in the forepart of the system had achieved about 97%. The removal efficiency of chemical oxygen demand (COD) and colour had the similar trend after physicochemical treatment and were corresponding to the proportion of suspended and the near-colloidal organic matter in the wastewater. After biological treatment, the removal efficiency of COD and colour achieved were about 97% and 90%, respectively. Furthermore, molecular weight (MW) distribution analysis showed that after treatment low MW molecules (chromatography/mass spectrometry showed that the composition of organic matter in the wastewater was not complicated. Methylsiloxanes were the typical organic components in the raw wastewater and most of them were removed after treatment.

  12. Full-Breadth Analysis of CD8+ T-Cell Responses in Acute Hepatitis C Virus Infection and Early Therapy

    Science.gov (United States)

    Lauer, Georg M.; Lucas, Michaela; Timm, Joerg; Ouchi, Kei; Kim, Arthur Y.; Day, Cheryl L.; zur Wiesch, Julian Schulze; Paranhos-Baccala, Glaucia; Sheridan, Isabelle; Casson, Deborah R.; Reiser, Markus; Gandhi, Rajesh T.; Li, Bin; Allen, Todd M.; Chung, Raymond T.; Klenerman, Paul; Walker, Bruce D.

    2005-01-01

    Multispecific CD8+ T-cell responses are thought to be important for the control of acute hepatitis C virus (HCV) infection, but to date little information is actually available on the breadth of responses at early time points. Additionally, the influence of early therapy on these responses and their relationships to outcome are controversial. To investigate this issue, we performed comprehensive analysis of the breadth and frequencies of virus-specific CD8+ T-cell responses on the single epitope level in eight acutely infected individuals who were all started on early therapy. During the acute phase, responses against up to five peptides were identified. During therapy, CD8+ T-cell responses decreased rather than increased as virus was controlled, and no new specificities emerged. A sustained virological response following completion of treatment was independent of CD8+ T-cell responses, as well as CD4+ T-cell responses. Rapid recrudescence also occurred despite broad CD8+ T-cell responses. Importantly, in vivo suppression of CD3+ T cells using OKT3 in one subject did not result in recurrence of viremia. These data suggest that broad CD8+ T-cell responses alone may be insufficient to contain HCV replication, and also that early therapy is effective independent of such responses. PMID:16189000

  13. Plan and safety analysis on the high power irradiation test program of full length fuel element for Hanaro

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Y.S.; Kim, C.K.; Park, H.D.; Kim, K.H.; Park, J.M.; Lee, D.B.; Kim, J.D.; Ko, Y.M.; Jang, S.J.; Ahn, H.S.; Woo, Y.M.; Kim, E.S.; Kim, H.R.; Chae, H.T.; Lee, C.S

    1999-06-01

    The advanced research reactor fuel development project has been carried out for a localization of HANARO nuclear fuels. The design and fabrication technologies of the localized fuel are almost developed, and the quality assurance procedure and assessment criteria were established. The characteristics of the fuel fabricated in KAERI were investigated through out-pile test. In order to verify the localized fuel performance, irradiation test plan of the developed fuel has been worked out. It consists of 3 stages. The 1st stage is normal power irradiation test and the final burn-up of the test fuel was supposed to be 85 at%. The fuel has been successfully irradiated until now and will be unloaded in June. The 2nd irradiation test will be done to confirm the fuel performance and to get the in-pile data under the high neutron flux level. This test fuel is identical with the 36-element fuel assembly. After the 1st and 2nd irradiation tests are completed with acceptable results, the 3rd irradiation test of final stage will be carried out as a demonstration. In this report, the results of the 1st irradiation test is introduced. Then the objectives, schedule and test condition, the design documents of fuel elements and bundle, the methods of fabrication, out-pile test results, post-irradiation examination scheme, calculation of linear power distribution, and safety analysis results for the 2nd irradiation test bundle are described. (author). 2 refs., 14 tabs., 12 figs.

  14. A Vectorial modeling for the pentaphase Permanent Magnet Synchronous Machine based on multimachine approach

    Directory of Open Access Journals (Sweden)

    Abdelkrim Sellam

    2012-12-01

    Full Text Available The polyphase [1] machines are developed mainly in the field of variable speed drives of high power because increasing the number of phases on the one hand allows to reduce the dimensions of the components in power modulators energy and secondly to improve the operating safety. By a vector approach (vector space, it is possible to find a set of single-phase machine and / or two-phase fictitious equivalent to polyphase synchronous machine.These fictitious machines are coupled electrically and mechanically but decoupled magnetically. This approach leads to introduce the concept of the equivalent machine (multimachine multiconverter system MMS which aims to analyze systems composed of multiple machines (or multiple converters in electric drives. A first classification multimachine multiconverter system follows naturally from MMS formalism. We present an example of a synchronous machine pent phase.

  15. A Vectorial modeling for the pentaphase Permanent Magnet Synchronous Machine based on multimachine approach

    Directory of Open Access Journals (Sweden)

    Abdelkrim Sellam,Boubakeur Dehiba,Mohamed B. Benabdallah,Mohamed Abid,Nacéra Bachir Bouiadjra,Boubakeur Bensaid,Mustapha Djouhri

    2012-12-01

    Full Text Available The polyphase [1] machines are developed mainly inthe field of variable speed drives of high powerbecause increasing the number of phases on the onehand allows to reduce the dimensions of thecomponents in power modulators energy and secondlyto improve the operating safety. By a vector approach(vector space, it is possible to find a set of singlephasemachine and / or two-phase fictitious equivalentto polyphase synchronous machine.These fictitiousmachines are coupled electrically and mechanicallybut decoupled magnetically. This approach leads tointroduce the concept of the equivalent machine(multimachine multiconverter system MMS whichaims to analyze systems composed of mul tiplemachines (or multiple converters in electric drives. Afirst classification multimachine multiconvertersystem follows naturally from MMS formalism. Wepresent an example of a synchronous machine pent

  16. [Vectorial angle method for studying on GC fingerprint of naphtha in Alpinia officinarum Hance].

    Science.gov (United States)

    Feng, Yi-Fan; Zhou, Xuan; Guo, Xiao-Ling

    2006-01-01

    To establish GC quality analysis and GC fingerprint spectrum of naphtha in Alpinia officinarum Hance. The naphtha in Alpinia officinarum Hance was extracted and analyzed by GC to establish the fingerprint spectrum. The results were analyzed by similarity grade calculate method to compare the fingerprint difference of Alpinia officinarum Hance. The GC fingerprint spectrum of Alpinia officinarum Hance were established. It consisted of 11 peaks. The GC spectrum results were analyzed by similarity grade calculate method which can divide Alpinia officinarum Hance into various habitats. The fingerprint spectrum can be used to distinguish Alpinia officinarum Hance and to evaluate its quality.

  17. Fully-vectorial simulation and tolerancing of optical systems for wafer inspection by field tracing

    Science.gov (United States)

    Asoubar, Daniel; Schweitzer, Hagen; Hellmann, Christian; Kuhn, Michael; Wyrowski, Frank

    2015-06-01

    The simulation, design and tolerancing of optical systems for wafer inspection is a challenging task due to the different feature sizes, which are involved in these systems. On the one hand light is propagated through macroscopic lens systems and on the other hand light is diffracted at microscopic structures with features in the range of the wavelength of light. Due to this variety of scale plenty of different physical effects like refraction, diffraction, interference and polarization have to be taken into account for a realistic analysis of such inspection systems. We show that all of these effects can be included in a system simulation by field tracing, which combines physical and geometrical optics. The main idea is the decomposition of the complex optical setup in a sequence of subdomains. Per subdomain a different approximative or rigorous solution of Maxwell's equations is applied to propagate the light. In this work the different modeling techniques for the analysis of an exemplary wafer inspection system are discussed in detail. These techniques are mainly geometrical optics for the light propagation through macroscopic lenses, a rigorous Fourier Modal Method (FMM) for the modeling of light diffraction at the wafer microstructure and different free-space diffraction integrals. In combination with a numerically efficient algorithm for the coordinate transformation of electromagnetic fields, field tracing enables position and fabrication tolerancing. As an example different tilt tolerance effects on the polarization state and image contrast of a simple wafer inspection system are shown.

  18. Aftershock mechanisms from the 2010 Mw 8.8 Maule, Chile earthquake: detailed analysis using full waveform inversion

    Science.gov (United States)

    Rietbrock, A.; Hicks, S. P.; Chagas, B.; Detzel, H. A.

    2014-12-01

    slip style can be highly variable across the megathrust, with implications for fault processes such as postseismic fluid release. We also perform 3-D full waveform forward simulation using the spectral element code, SPECFEM3D, to understand the sensitivity of our moment tensor solutions with respect to 3-D velocity structure.

  19. Rainfall/runoff simulation with 2D full shallow water equations: Sensitivity analysis and calibration of infiltration parameters

    Science.gov (United States)

    Fernández-Pato, Javier; Caviedes-Voullième, Daniel; García-Navarro, Pilar

    2016-05-01

    One of the most difficult issues in the development of hydrologic models is to find a rigorous source of data and specific parameters to a given problem, on a given location that enable reliable calibration. In this paper, a distributed and physically based model (2D Shallow Water Equations) is used for surface flow and runoff calculations in combination with two infiltration laws (Horton and Green-Ampt) for estimating infiltration in a watershed. This technique offers the capability of assigning a local and time-dependent infiltration rate to each computational cell depending on the available surface water, soil type or vegetation. We investigate how the calibration of parameters is affected by transient distributed Shallow Water model and the complexity of the problem. In the first part of this work, we calibrate the infiltration parameters for both Horton and Green-Ampt models under flat ponded soil conditions. Then, by means of synthetic test cases, we perform a space-distributed sensitivity analysis in order to show that this calibration can be significantly affected by the introduction of topography or rainfall. In the second part, parameter calibration for a real catchment is addressed by comparing the numerical simulations with two different sets of experimental data, corresponding to very different events in terms of the rainfall volume. We show that the initial conditions of the catchment and the rainfall pattern have a special relevance in the quality of the adjustment. Hence, it is shown that the topography of the catchment and the storm characteristics affect the calibration of infiltration parameters.

  20. The Full-length Genome Analysis of a Street Rabies Virus Strain Isolated in Yunnan Province of China

    Institute of Scientific and Technical Information of China (English)

    Jian Zhang; Hai-lin Zhang; Xiao-yan Tao; Hao Li; Qing Tang; Xiu-yun Jiang; Guo-dong Liang

    2012-01-01

    The epidemic of rabies has rapidly increased and expanded in Yunnan province in recent years.In order to further analyze and understand the etiological reasons for the rapid expansion of rabies in Yunnan,a strain of rabies virus CYN1009D in Yunnan was isolated,and the complete genomic sequencing was carried out,and the bioimfomative analysis on genes/encoded proteins and phylogeny with reference to sequences in GenBank was performed.The complete genome of CYN1009D was 11923 nt in length and belonged to genotype I.The genes encoding different structural proteins were all conserved in their lengths,in comparison to other strains in China.The amino acid sequence was conserved at different antigen sites of NP,but the variation was detected at the secondary phosphorylation site of position 375; variations were also detected in the phosphorylation sites at positions 63-63 and 162 of PP; the sites playing important roles in virus synthesis,budding and viral morphology in MP were conserved; two glycosylation sites were detected at Asn37 and Asn319in GP,the neutralizing antigen sites in GP were conserved; the initial amino acid of LP (ML) was different from that of most of the strains in China (MM); the variations in G-L region in the intergenic region were significant.The phylogenic tree showed that CYN1009D has a closer genetic relationship to the strains in Southeast Asia,indicating that prevention and control on rabies in borderland areas should be reinforced meanwhile efforts are made to control rabies in China.

  1. Vectorial competence of Aedes aegypti (Linnaeus 1762 Rio de Janeiro Strain, to Dirofilaria immitis (Leidy 1856

    Directory of Open Access Journals (Sweden)

    Maria Lúcia Serrão

    2001-07-01

    Full Text Available Dirofilaria immitis (Leidy 1856, a nematode parasite, is the etiologic agent of canine heartworm disease and mosquitoes are essential intermediate hosts. Mosquito susceptibility to the worms differ with species, strains and also among individuals of the same strain. To evaluate the degree of susceptibility of Rio de Janeiro laboratory raised strain of Aedes aegypti, we fed mosquitoes on canine blood with different densities of microfilariae (mf. There was no significant difference in the rate of development among the three different densities of mf. Infective larvae were found in the head and proboscis of all mosquitoes provided bloodmeals with different densities of mf after the 11th day post-infection. The infection rate of mosquitoes after ingestion of blood containing 3,000 mf/ml, 5,000 mf/ml and 7,000 mf/ml were 55.3%, 66.7% and 100%, respectively. The vector efficiency indices ranged from 1.6 to 9.3. The finding of L3 stage larvae, high infection rates and vector efficiency indices suggest that Ae. aegypti, Rio de Janeiro laboratory strain, is a potential vector of D. immitis, although of low efficiency.

  2. Full Nutrient Compositions Analysis of Tropical Fruit Borojo%热带水果Borojo全营养素分析

    Institute of Scientific and Technical Information of China (English)

    焦红; 孟平; 李丹; 刘江晖; 刘超; 黄华军; 梁公璧; 黄健豪

    2011-01-01

    [Objective] To study the full nutrient compositions of a kind of Ecuadorian tropical fruit called Borojo and to provide the scientific basis for the development of new resources and functional foods. [Method] A total of 4 fresh fruits were processed to the pulp, which were for 188 testing projects such as protein, pH, moisture, ash, total sugar, crude fiber, plant oil, vitamins, minerals, rare earth elements, hydrolysis amino acids, free amino acids, fatty acids based on China national standard testing methods by UV spectrophotometry, HPLC, GC, ICE HPLC/MS/MS, and ICP/MS. [Result] Fresh Borojo flesh was highly acidic (pH 2.74), moisture content was 70.99%, carbohydrate content was 25.07%, total sugar content was 9.72%, protein content was 1.5% and crude fiber content was 2.14%. The contents of VB1, VB2, niacin, folic acid, VC and VE was 0.05mg/kg, 0.81mg/kg, 0.71mg/kg, 0.22mg/kg, 4.32mg/kg, and 2.49mg/kg respectively. Borojo containd 26 different kinds of free amino acids, and the total content was 1.35%. After hydrolysis, there were 20 kinds of free amino acids and the total content was 2.51% . Borojo was rich in minerals.The dry flesh contained potassium(8 797.8mg/kg), magnesium (280mg/kg), calcium(1 030.6mg/kg), phosphorus(775.2mg/kg), iron (160mg/kg), boron(25.2mg/kg) and sodium (11.8mg/kg). It also contained essential trace elements (such as zinc, copper and iron) and other specific trace elements with manganese, silicon, trivalent chromium and nickel which were rarely appear in fruits and vegetables. Borojo also contains 16 kinds of rare earth elements within the normal range. Lead concentration was 0.065mg/kg. The contained of mercury, arsenic and cadmium are all below the minimum detection limits. The fatty acid was 1.28% contents of linoleic acid (9.91%) and linolenic acid (0.89%). [Conclusion] Borojo had complex compositions and rich nutrients, and its components had excellent utility value to be developed into

  3. Far-field method for the characterisation of three-dimensional fields: vectorial polarimetry

    Science.gov (United States)

    Rodríguez, O.; Lara, D.; Dainty, C.

    2010-06-01

    The first attempt to completely characterise a three-dimensional field was done by Ellis and Dogariu with excellent results reported [1] . However, their method is based on near-field techniques, which limits its range of applications. In this work, we present an alternative far-field method for the characterisation of the three-dimensional field that results from the interaction of a tightly focused three-dimensional field [2] with a sub-resolution specimen. Our method is based on the analysis of the scattering-angle-resolved polarisation state distribution across the exit pupil of a high numerical aperture (NA) collector lens using standard polarimetry techniques. Details of the method, the experimental setup built to verify its capabilities, and numerical and first experimental evidence demonstrating that the method allows for high sensitivit y on sub-resolution displacements of a sub-resolution specimen shall be presented [3]. This work is funded by Science Foundation Ireland grant No. 07/IN.1/I906 and Shimadzu Corporation, Japan. Oscar Rodríguez is grateful to the National Council for Science and Technology (CONACYT, Mexico) for the Ph D scholarship 177627.

  4. La vulnerabilidad humana a la transmisión vectorial de Trypanosoma cruzi a través de los procesos de salud-enfermedad y la apropiación social del territorio

    Directory of Open Access Journals (Sweden)

    Alba Rocío Valdez Tah

    2015-01-01

    Full Text Available Los estudios sobre el riesgo de la transmisión vectorial de Trypanosoma cruzi a población humana han desatendido el rol del comportamiento y de la subjetividad de las relaciones sociales en el marco del paisaje natural y el contexto social. A través de una revisión y síntesis de la bibliografía sobre los factores biológicos, ecoepidemiológicos y socioculturales que intervienen en el fenómeno, en conjunto con un estudio etnográfico, se propone un modelo de análisis del riesgo que distingue los componentes de peligro y de la vulnerabilidad humana. Los conocimientos, prácticas y representaciones sociales respecto del proceso salud-enfermedad-atención y de la apropiación social del territorio se plantean como elementos explicativos de la vulnerabilidad humana. Los componentes de la vulnerabilidad propuestos se exploran en el marco de un análisis etnográfico, que permite identificar opciones y medidas preventivas o de control integral del riesgo más adecuadas.

  5. Vectorial status and insecticide resistance of Anopheles funestus from a sugar estate in southern Mozambique

    Directory of Open Access Journals (Sweden)

    Nhamahanga Eduardo

    2011-02-01

    Full Text Available Abstract Background The dual problems of rising insecticide resistance in the malaria vectors and increasing human malaria cases since 2001 in southern Mozambique are cause for serious concern. The selection of insecticides for use in indoor residual spraying (IRS programmes is highly dependent on the extent to which local mosquitoes are susceptible to the approved classes of insecticides. The insecticide resistance status and role in malaria transmission of Anopheles funestus was evaluated at the Maragra Sugar Estate in southern Mozambique where an IRS vector control programme has been in operation for seven years using the carbamate insecticide bendiocarb. Results No Anopheles species were captured inside the sugar estate control area. Anopheles funestus group captured outside of the estate represented 90% (n = 475 of the total collections. Of the specimens identified to species by PCR (n = 167, 95% were An. funestus s.s. One An. rivulorum was identified and seven specimens did not amplify. The Anopheles gambiae complex was less abundant (n = 53 and of those identified (n = 33 76% were An. arabiensis and 24% An. merus. Insecticide susceptibility tests showed that wild-caught and F-1 family An. funestus were resistant to deltamethrin (32.5% mortality and lambda-cyhalothrin (14.6% mortality, less so to bendiocarb (71.5% mortality and fully susceptible to both malathion and DDT (100%. Bendiocarb and pyrethroid resistance was nullified using 4% piperonyl butoxide (Pbo, strongly suggesting that both are mediated by P450 monooxygenase detoxification. ELISA tests of An. funestus for Plasmodium falciparum, gave a sporozoite rate of 6.02% (n = 166. One unidentified member of the An. gambiae complex tested positive for P. falciparum sporozoites. Conclusion Anopheles funestus was found to be the most abundant and principle vector of malaria in this area, with members of the An. gambiae complex being secondary vectors. Despite the continual use of

  6. The mosquitoes (Diptera: Culidae of Seychelles: taxonomy, ecology, vectorial importance, and identification keys

    Directory of Open Access Journals (Sweden)

    Le Goff Gilbert

    2012-09-01

    Full Text Available Abstract Background During recent periods, the islands of the Republic of Seychelles experienced many diseases such as dengue, chikungunya, Bancroft’s filaria and malaria. Mosquitoes transmit the agents that cause these diseases. Published information on mosquitoes in the Seychelles is notably dispersed in the literature. The maximum number of species obtained on a single field survey does not exceed 14 species. Methods We performed a comprehensive bibliographic review using mosquito and Seychelles as the key words, as well as conducted a mosquito field survey for larval and adult stages during the rainy season in December 2008. Sixteen sites were sampled on four granitic islands (Mahé, Praslin, La Digue and Aride and six sites on coralline atolls in the extreme southwest of the country (Aldabra group. Results We found published references to 21 mosquito species identified at least on one occasion in the Seychelles. Our collections comprised 18 species of mosquitoes, all of them from the subfamily Culicinae; no Anophelinae was found. We also confirm that Aedes seychellensis is a junior synonym of Ae. (Aedimorphus albocephalus. The first records for Culex antennatus and Cx. sunyaniensis are presented from the country, specifically from Aldabra and Praslin, respectively. Based on a comparison of the taxa occurring on the granitic versus coralline islands, only three species, Ae. albocephalus, Cx. scottii and Cx. simpsoni are shared. Aedes albopictus appeared to exclude largely Ae. aegypti on the granitic islands; however, Ae. aegypti was common on Aldabra, where Ae. albopictus has not been recorded. The notable aggressiveness of mosquitoes towards humans on coralline islands was mainly due to two species, the females of which are difficult to distinguish: Ae. fryeri and Ae. (Aedimorphus sp. A. The number of mosquito species collected at least once in the Seychelles is now 22, among which five species (Ae. (Adm sp. A, Cx. stellatus, Uranotaenia

  7. Full Scan MS in Comprehensive Qualitative and Quantitative Residue Analysis in Food and Feed Matrices: How Much Resolving Power is Required?

    NARCIS (Netherlands)

    Kellmann, M.; Muenster, H.; Zomer, P.; Mol, J.G.J.

    2009-01-01

    In LC full scan based MS screening methods correct mass assignment is essential. Parameters affecting the accuracy of mass assignment, i.e., analyte concentration, complexity of the matrix, and resolving power, were studied using typical examples from the field of residue and contaminant analysis in

  8. Influence of an externally applied magnetic field on vectorial interaction in LiNbO3:Fe crystals

    DEFF Research Database (Denmark)

    Dam-Hansen, C.; Johansen, P.M.; Petersen, P.M.

    1995-01-01

    -beam gain and the diffraction efficiency of up to 40 and 75 %, respectively. The magnitude depends on the direction of the magnetic field. The interaction is believed to occur due to the anomalously high mobility of the nonthermalized free electrons responsible for the photovoltaic current, which...... in the vectorial interaction scheme causes the grating formation. A phenomenological description of the photovoltaic current including the photo-flail effect shows a linear dependence on the magnetic field, which does not explain the obtained experimental results....

  9. Conjeturas al realizar una tarea asociada a una ecuación vectorial de la recta con el apoyo de geometría dinámica

    OpenAIRE

    Soler, María Nubia; Carranza, Edwin; Samboní, Yuri; Pinzón, Mery

    2012-01-01

    En este taller los participantes, a partir del desarrollo de una tarea, identifican algunas etapas en la formulación y validación de conjeturas. La tarea se centra en la exploración de un applet relacionado con la ecuación vectorial de la recta en el plano, a partir del cual se identifican algunas propiedades geométricas del objeto geométrico y, con estas, se establecen e intentan validar generalidades. Este taller surge en el marco del proyecto de investigación “Razonamientos abductivos, ind...

  10. Superposition of nonparaxial vectorial complex-source spherically focused beams: Axial Poynting singularity and reverse propagation

    Science.gov (United States)

    Mitri, F. G.

    2016-08-01

    In this work, counterintuitive effects such as the generation of an axial (i.e., long the direction of wave motion) zero-energy flux density (i.e., axial Poynting singularity) and reverse (i.e., negative) propagation of nonparaxial quasi-Gaussian electromagnetic (EM) beams are examined. Generalized analytical expressions for the EM field's components of a coherent superposition of two high-order quasi-Gaussian vortex beams of opposite handedness and different amplitudes are derived based on the complex-source-point method, stemming from Maxwell's vector equations and the Lorenz gauge condition. The general solutions exhibiting unusual effects satisfy the Helmholtz and Maxwell's equations. The EM beam components are characterized by nonzero integer degree and order (n ,m ) , respectively, an arbitrary waist w0, a diffraction convergence length known as the Rayleigh range zR, and a weighting (real) factor 0 ≤α ≤1 that describes the transition of the beam from a purely vortex (α =0 ) to a nonvortex (α =1 ) type. An attractive feature for this superposition is the description of strongly focused (or strongly divergent) wave fields. Computations of the EM power density as well as the linear and angular momentum density fluxes illustrate the analysis with particular emphasis on the polarization states of the vector potentials forming the beams and the weight of the coherent beam superposition causing the transition from the vortex to the nonvortex type. Should some conditions determined by the polarization state of the vector potentials and the beam parameters be met, an axial zero-energy flux density is predicted in addition to a negative retrograde propagation effect. Moreover, rotation reversal of the angular momentum flux density with respect to the beam handedness is anticipated, suggesting the possible generation of negative (left-handed) torques. The results are particularly useful in applications involving the design of strongly focused optical laser

  11. Oil spill analysis by means of full polarimetric UAVSAR (L-band) and Radarsat-2 (C-band) products acquired during Deepwater Horizon Disaster

    Science.gov (United States)

    Latini, Daniele; Del Frate, Fabio; Jones, Cathleen E.

    2014-10-01

    SAR instruments with polarimetric capabilities, high resolution and short revisit time can provide powerful support in oil spill monitoring and different techniques of analysis have been developed for this purpose [1][2]. An oil film on the sea surface results in darker areas in SAR images, but careful interpretation is required because dark spots can also be caused by natural phenomena. In view of the very low backscatter from slicks, the Noise Equivalent Sigma Zero (NESZ) is a primary sensor parameter to be considered when using a sensor for slick analysis. Among the existing full polarimetric sensors, the high resolution and very low NESZ values of UAVSAR (L-band) and RADARSAT-2 (C-band) make them preferable for oil spill analysis compared to the last generation SAR instruments. The Deepwater Horizon disaster that occurred in the Gulf of Mexico in 2010 represents a unique and extensive test site where large amounts of SAR imagery and ground validation data are available. By applying the Cloude-Pottier decomposition method to full polarimetric UAVSAR (L-band) and RADARSAT-2 (C-band), it is possible to extract parameters that describe the scattering mechanism of the target. By comparing quasi-simultaneous acquisitions and exploiting the different penetration capabilities of the sensors, we investigate the potential of full polarimetric SAR to discriminate oil on the sea surface from look-alike phenomena covering the full range of backscattering values down to those at the instrument noise floor.

  12. Tool Wear Analysis on Five-Axis Flank Milling for Curved Shape Part – Full Flute and Ground Shank End Mill

    Directory of Open Access Journals (Sweden)

    Syahrul Azwan Sundi

    2017-01-01

    Full Text Available This paper is a study on full flute (extra-long tool and ground shank end mill wear analysis by utilizing five-axis CNC to implement flank milling strategy on curved shape part. Five-axis machining eases the user to implement variations of strategy such as flank milling. Flank milling is different from point milling. Point milling cuts materials by using the tip of the tool whereas the flank milling uses the cutting tool body to cut material. The type of cutting tool used was end mill 10 mm diameter with High Speed Steel (HSS material. One factor at a time was utilized to analyze the overall data. Feed rate and spindle speed were the two main factors that been set up equally for both full flute and ground shank end mill. At the end of this research, the qualitative analysis based on tool wear between full flute and ground shank end mill is observed. Generally, both types of cutting tools showed almost the same failure indication such as broken edge or chipped off edge, formation of pinned hole on the surface and serration formation or built-up edge (BUE on the primary flute. However, the results obtained from the enlarged images which were captured by Optical Microscope indicated that, the ground shank end mill is better than the full flute end mill.

  13. Fully vectorial laser resonator modeling of continuous-wave solid-state lasers including rate equations, thermal lensing and stress-induced birefringence.

    Science.gov (United States)

    Asoubar, Daniel; Wyrowski, Frank

    2015-07-27

    The computer-aided design of high quality mono-mode, continuous-wave solid-state lasers requires fast, flexible and accurate simulation algorithms. Therefore in this work a model for the calculation of the transversal dominant mode structure is introduced. It is based on the generalization of the scalar Fox and Li algorithm to a fully-vectorial light representation. To provide a flexible modeling concept of different resonator geometries containing various optical elements, rigorous and approximative solutions of Maxwell's equations are combined in different subdomains of the resonator. This approach allows the simulation of plenty of different passive intracavity components as well as active media. For the numerically efficient simulation of nonlinear gain, thermal lensing and stress-induced birefringence effects in solid-state active crystals a semi-analytical vectorial beam propagation method is discussed in detail. As a numerical example the beam quality and output power of a flash-lamp-pumped Nd:YAG laser are improved. To that end we compensate the influence of stress-induced birefringence and thermal lensing by an aspherical mirror and a 90° quartz polarization rotator.

  14. Is single-strand conformation polymorphism analysis of the full 5' untranslated region an adequate approach to study hepatitis C virus quasispecies distribution?

    Science.gov (United States)

    Vera-Otarola, Jorge; Barría, María Inés; León, Ursula; Carvallo, Pilar; Soza, Alejandro; López-Lastra, Marcelo

    2009-09-01

    Single-strand conformation polymorphism (SSCP) analysis is used by many laboratories to study the quasispecies distribution of the hepatitis C virus (HCV). Here we question the validity of this experimental approach, as conclusions are drawn from the analysis of the migration patterns of two ssDNA molecules and not from RNA. Using previously characterized mutants of the HCV 5' untranslated regions, we show that contrary to what has been predicted, SSCP migration patterns of DNA amplicons with differences in their nucleotide sequences generated from the full 5' UTR of HCV are not necessarily unique.

  15. Is Single-Strand Conformation Polymorphism Analysis of the Full 5′ Untranslated Region an Adequate Approach To Study Hepatitis C Virus Quasispecies Distribution? ▿

    Science.gov (United States)

    Vera-Otarola, Jorge; Barría, María Inés; León, Ursula; Carvallo, Pilar; Soza, Alejandro; López-Lastra, Marcelo

    2009-01-01

    Single-strand conformation polymorphism (SSCP) analysis is used by many laboratories to study the quasispecies distribution of the hepatitis C virus (HCV). Here we question the validity of this experimental approach, as conclusions are drawn from the analysis of the migration patterns of two ssDNA molecules and not from RNA. Using previously characterized mutants of the HCV 5′ untranslated regions, we show that contrary to what has been predicted, SSCP migration patterns of DNA amplicons with differences in their nucleotide sequences generated from the full 5′ UTR of HCV are not necessarily unique. PMID:19553315

  16. Design and analysis of full pitch winding and concentrated stator pole winding three-phase flux reversal machine for low speed application

    Indian Academy of Sciences (India)

    D S More; Hari Kalluru; B G Fernandes

    2008-10-01

    The flux reversal machine (FRM) is a doubly-salient stator permanent magnet machine with flux linkage reversal in the stator concentrated winding. The existing machines at low speed, low power (2·4 kW, 300 rpm) range are not economical. FRM topology is best suited for this application. An attempt has been made to improve the power density of machine by introducing full pitch winding. Full pitch winding FRM (FPFRM) has higher power density than the conventional concentrated stator pole winding FRM (CSPFRM). Design and comparative analysis of FPFRM and CSPFRM are made. Both machines are designed for 88·58 Nm and 300 rpm. Design details of both machines are presented. Finite Element Method (FEM) analysis is carried out to evaluate and compare the performance of CSPFRM and FPFRM. Series capacitive compensation is provided for better voltage regulation of both machines.

  17. Generation and analysis of large-scale expressed sequence tags (ESTs) from a full-length enriched cDNA library of porcine backfat tissue

    OpenAIRE

    2006-01-01

    Background Genome research in farm animals will expand our basic knowledge of the genetic control of complex traits, and the results will be applied in the livestock industry to improve meat quality and productivity, as well as to reduce the incidence of disease. A combination of quantitative trait locus mapping and microarray analysis is a useful approach to reduce the overall effort needed to identify genes associated with quantitative traits of interest. Results We constructed a full-lengt...

  18. Full second order chromatographic/spectrometric data matrices for automated sample identification and component analysis by non-data-reducing image analysis

    DEFF Research Database (Denmark)

    Nielsen, Niles-Peter Vest; Smedsgaard, Jørn; Frisvad, Jens Christian

    1999-01-01

    A data analysis method is proposed for identification and for confirmation of classification schemes, based on single- or multiple-wavelength chromatographic profiles. The proposed method works directly on the chromatographic data without data reduction procedures such as peak area or retention...... index calculation, Chromatographic matrices from analysis of previously identified samples are used for generating a reference chromatogram for each class, and unidentified samples are compared with all reference chromatograms by calculating a resemblance measure for each reference. Once the method...... yielded over 90% agreement with accepted classifications. The method is highly accurate and may be used on all sorts of chromatographic profiles. Characteristic component analysis yielded results in good agreement with existing knowledge of characteristic components, but also succeeded in identifying new...

  19. Expressed Sequence Tags Analysis and Design of Simple Sequence Repeats Markers from a Full-Length cDNA Library in Perilla frutescens (L.

    Directory of Open Access Journals (Sweden)

    Eun Soo Seong

    2015-01-01

    Full Text Available Perilla frutescens is valuable as a medicinal plant as well as a natural medicine and functional food. However, comparative genomics analyses of P. frutescens are limited due to a lack of gene annotations and characterization. A full-length cDNA library from P. frutescens leaves was constructed to identify functional gene clusters and probable EST-SSR markers via analysis of 1,056 expressed sequence tags. Unigene assembly was performed using basic local alignment search tool (BLAST homology searches and annotated Gene Ontology (GO. A total of 18 simple sequence repeats (SSRs were designed as primer pairs. This study is the first to report comparative genomics and EST-SSR markers from P. frutescens will help gene discovery and provide an important source for functional genomics and molecular genetic research in this interesting medicinal plant.

  20. Cloning and Sequence Analysis of Interleukin 10 (IL-10) Full-length cDNA from Cyprinus carpio L.

    Institute of Scientific and Technical Information of China (English)

    Xiangru FENG; Yilong CHEN; Xiao ZHAO; Wendong WANG; Junhui ZHANG; Zhenguo YANG SUN; Shengmei JIA; Qiang LU

    2012-01-01

    Abstract [Objective] This study aimed to obtain IL-IO (interleukin 10) full-length cD- NA of common carp (Cyprinus carpio L.) and conduct the sequence analysis. []~lethod] The differentially expressed cDNA fragment was obtained by DD-RTPCR (differential display RT-PCR). The cDNA library of peripheral blood leukocytes which were separated from common carp and stimulated by mitogen was screened with a probe labeled with DIG (digoxigenin). The IL-IO full-length cDNA was cloned from 0.8x104 pfu of recombinant phages, and the sequence analysis and homology com- parison were carried out. [Result] Sequence analysis indicated that the IL-IO full- length cDNA of common carp was 1 117 bp long, containing a.55 bp 5'-UTR, a 522 bp 3"-UTR, and a 540 bp open reading frame(ORF) encoding 179 amino acids. In addition, there were three mRNA instability motifs (ATTTA) in the 3"-untranslated region. The deduced protein sequence shared typical sequence features of the IL-IO family. Homology comparison indicated that the obtained sequence shared 89.1% homology with the carp IL-IO gene from GenBank. [Conclusion] This study laid foun- dation for further study of the expression manner, functional characteristic and regu- lation mechanism of IL-IO in vivo and the interaction mechanism in the inflammatory reaction and immune response.

  1. Plot of the transverse mass distributions for events passing the full selection of the H→WW∗→lνlν analysis

    CERN Multimedia

    ATLAS, Collection

    2013-01-01

    The transverse mass distributions for events passing the full selection of the H→WW∗→lνlν analysis summed over all lep- ton flavours for final states with Njet ≤ 1. The signal is stacked on top of the background. The hatched area represents the total uncertainty on the sum of the signal and background yields from statistical, experimental, and theoretical sources. The residuals of the data with respect to the estimated background are shown, compared to the expected mT distribution of a SM Higgs boson.

  2. Analysis, Design, Modelling and Control of an Interleaved-Boost Full-Bridge Three-Port Converter for Hybrid Renewable Energy Systems

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen; Zhang, Zhe; Knott, Arnold;

    2016-01-01

    This paper presents the design, modelling and control of a three-port (TPC) isolated dc-dc converter based on interleaved-boost-full-bridge with pulse-width-modulation and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven by phase-shifted PWM...... of the proposed ac inductor based TPC is investigated by performing state-space modelling. Moreover, the derived mathematical models are validated by simulation and measurements. In order to verify the validity of the theoretical analysis, design and power decoupling control scheme, a prototype is constructed...

  3. Transient analysis and control of bias magnetic state in the transformer of on-line pulse-width-modulation switching full bridge direct current-direct current converter

    Science.gov (United States)

    Chen, Jiaxin; Guo, Youguang; Zhu, Jianguo; Wei Lin, Zhi

    2012-04-01

    This paper presents a finite element analysis (FEA) based method for analyzing and controlling the bias magnetic state of the transformer of a pulse-width-modulation (PWM) switching full bridge dc-dc converter. A field-circuit indirect coupling method for predicting the transient bias magnetic state is introduced first. To increase flexibility of the proposed method, a novel transformer model which can address not only its basic input-output characteristic, but also the nonlinear magnetizing inductance, is proposed. Both the asymmetric characteristic and the variable laws of the current flowing through the two secondary windings during the period of PWM switching-off state are highlighted. Finally, the peak magnetizing current controlled method based on the on-line magnetizing current computation is introduced. Analysis results show that this method can address the magnetic saturation at winding ends, and hence many previous difficulties, such as the start-up process and asymmetry of power electronics, can be easily controlled.

  4. Sequencing and analysis of full-length cDNAs, 5'-ESTs and 3'-ESTs from a cartilaginous fish, the elephant shark (Callorhinchus milii.

    Directory of Open Access Journals (Sweden)

    Yue Ying Tan

    Full Text Available Cartilaginous fishes are the most ancient group of living jawed vertebrates (gnathostomes and are, therefore, an important reference group for understanding the evolution of vertebrates. The elephant shark (Callorhinchus milii, a holocephalan cartilaginous fish, has been identified as a model cartilaginous fish genome because of its compact genome (∼910 Mb and a genome project has been initiated to obtain its whole genome sequence. In this study, we have generated and sequenced full-length enriched cDNA libraries of the elephant shark using the 'oligo-capping' method and Sanger sequencing. A total of 6,778 full-length protein-coding cDNA and 10,701 full-length noncoding cDNA were sequenced from six tissues (gills, intestine, kidney, liver, spleen, and testis of the elephant shark. Analysis of their polyadenylation signals showed that polyadenylation usage in elephant shark is similar to that in mammals. Furthermore, both coding and noncoding transcripts of the elephant shark use the same proportion of canonical polyadenylation sites. Besides BLASTX searches, protein-coding transcripts were annotated by Gene Ontology, InterPro domain, and KEGG pathway analyses. By comparing elephant shark genes to bony vertebrate genes, we identified several ancient genes present in elephant shark but differentially lost in tetrapods or teleosts. Only ∼6% of elephant shark noncoding cDNA showed similarity to known noncoding RNAs (ncRNAs. The rest are either highly divergent ncRNAs or novel ncRNAs. In addition to full-length transcripts, 30,375 5'-ESTs and 41,317 3'-ESTs were sequenced and annotated. The clones and transcripts generated in this study are valuable resources for annotating transcription start sites, exon-intron boundaries, and UTRs of genes in the elephant shark genome, and for the functional characterization of protein sequences. These resources will also be useful for annotating genes in other cartilaginous fishes whose genomes have been

  5. Microbial-based evaluation of foaming events in full-scale wastewater treatment plants by microscopy survey and quantitative image analysis.

    Science.gov (United States)

    Leal, Cristiano; Amaral, António Luís; Costa, Maria de Lourdes

    2016-08-01

    Activated sludge systems are prone to be affected by foaming occurrences causing the sludge to rise in the reactor and affecting the wastewater treatment plant (WWTP) performance. Nonetheless, there is currently a knowledge gap hindering the development of foaming events prediction tools that may be fulfilled by the quantitative monitoring of AS systems biota and sludge characteristics. As such, the present study focuses on the assessment of foaming events in full-scale WWTPs, by quantitative protozoa, metazoa, filamentous bacteria, and sludge characteristics analysis, further used to enlighten the inner relationships between these parameters. In the current study, a conventional activated sludge system (CAS) and an oxidation ditch (OD) were surveyed throughout a period of 2 and 3 months, respectively, regarding their biota and sludge characteristics. The biota community was monitored by microscopic observation, and a new filamentous bacteria index was developed to quantify their occurrence. Sludge characteristics (aggregated and filamentous biomass contents and aggregate size) were determined by quantitative image analysis (QIA). The obtained data was then processed by principal components analysis (PCA), cross-correlation analysis, and decision trees to assess the foaming occurrences, and enlighten the inner relationships. It was found that such events were best assessed by the combined use of the relative abundance of testate amoeba and nocardioform filamentous index, presenting a 92.9 % success rate for overall foaming events, and 87.5 and 100 %, respectively, for persistent and mild events.

  6. Influences of digital resource acquisition on scientific research behaviors——The statistical analysis on the full-text downloading quantity and cited times

    Institute of Scientific and Technical Information of China (English)

    LIU; Xiaomin; ZHANG; Jianyong

    2009-01-01

    With the emergence and further development of the digital library,the approaches of information acquisition correspondingly change a lot.This paper makes a statistical analysis on the journal downloading and citation behaviors under the digital environment conceived by the National Science Library(NSL),Chinese Academy of Sciences(CAS).It can be seen that the development of digital resources has influenced scientific research behaviors.For example,the large quantity of full-text downloading will maintain;the trend of journal downloading behaviors is basically same as the journal citation behavior;journals with large quantity of full-text downloading also boast the high cited times,and vice versa.Furthermore,authors make a linear regression analysis,with the journal downloading amount as the independent variable and journal cited times as dependent variable.Then they also prove the positive correlation between the journal downloading and citation behaviors by means of Pearson’s correlation coefficient formula.

  7. Shoulder-specific outcomes 1 year after nontraumatic full-thickness rotator cuff repair: a systematic literature review and meta-analysis.

    Science.gov (United States)

    Gurnani, Navin; van Deurzen, Derek F P; van den Bekerom, Michel P J

    2017-10-01

    Nontraumatic full-thickness rotator cuff tears are commonly initially treated conservatively. If conservative treatment fails, rotator cuff repair is a viable subsequent option. The objective of the present meta-analysis is to evaluate the shoulder-specific outcomes one year after arthroscopic or mini-open rotator cuff repair of nontraumatic rotator cuff tears. A literature search was conducted in PubMed and EMBASE within the period January 2000 to January 2017. All studies measuring the clinical outcome at 12 months after nontraumatic rotator cuff repair of full-thickness rotator cuff tears were listed. We included 16 randomized controlled trials that met our inclusion criteria with a total of 1.221 shoulders. At 12 months after rotator cuff repair, the mean Constant score had increased 29.5 points; the mean American Shoulder and Elbow Score score increased by 38.6 points; mean Simple Shoulder Test score was 5.6 points; mean University of California Los Angeles score improved by 13.0 points; and finally, mean Visual Analogue Scale score decreased by 4.1 points. Based on this meta-analysis, significant improvements in the shoulder-specific indices are observed 12 months after nontraumatic arthroscopic or mini-open rotator cuff repair.

  8. Do agents' characteristics affect their valuation of 'common pool' resources? A full-preference ranking analysis for the value of sustainable river basin management.

    Science.gov (United States)

    González Dávila, Osiel; Koundouri, Phoebe; Pantelidis, Theologos; Papandreou, Andreas

    2017-01-01

    In this paper we develop a full-preference ranking Choice Experiment (CE) designed to investigate how respondents evaluate a set of proposed improvements towards sustainable river basin management, as per the prescriptions of the European Union-Water Framework Directive (2000). The CE is applied in the Asopos River Basin (ARB) in Greece. Our interest is to test whether residency in the river basin, or otherwise, affects the preferences of the relevant agents. We first estimate a rank-ordered logistic regression based on a full set of choices in order to calculate the willingness to pay (WTP) of respondents for each one of the three attributes considered in the CE (i.e., environmental conditions, impact on the local economy and changes in the potential uses of water). The model is initially estimated for the full sample and then re-estimated twice for two sub-samples: the first one only includes the residents of Athens and the second only includes the residents of Asopos. Afterwards, we examine the effect of various demographic and socio-economic factors (such as income, gender, age, employment and education) on the estimates of our model in order to reveal any differences among respondents with different characteristics, mainly focusing on whether they reside or have personal experience of the RB under valuation. Thus, our analysis simultaneously provides a robustness check on previous findings in the literature and additional information about how various demographic and socio-economic characteristics affect the evaluation of the selected attributes.

  9. Analysis of a broadband dispersion compensating photonic crystal fiber raman amplifier

    DEFF Research Database (Denmark)

    Varshney, Shailendra K.; Saitoh, K.; Koshiba, M.;

    2006-01-01

    Using an accurate full-vectorial finite element method, a realistic model of a fabricated dispersion compensating photonic crystal fiber is analyzed. An almost flat Raman-gain spectrum (gain-ripples at just ±0.48-dB) is obtained using a single pump.......Using an accurate full-vectorial finite element method, a realistic model of a fabricated dispersion compensating photonic crystal fiber is analyzed. An almost flat Raman-gain spectrum (gain-ripples at just ±0.48-dB) is obtained using a single pump....

  10. 核辐射测井全能谱分析方法综述%The summarization for full spectrum analysis methods of radioactive logging

    Institute of Scientific and Technical Information of China (English)

    吴文圣; 张立娟

    2011-01-01

    多元素能谱测井通过全能谱分析方法求取单个地层元素的产额,进而求取元素重量百分含量和矿物百分含量,为识别复杂油气藏岩石类型和矿物类型、建立复杂油气藏新的测井解释模型及应用正确评价方法开辟了新的途径,为地质问题和工程问题的解决提供了新的手段,全能谱分析方法研究是当前国内核辐射测井研究热点之一.本文表分析多元素能谱测井的重要意义和研究现状的基础上,归纳总结了全能谱分析方法的研究现状、实现步骤、标准元素谱的获取方法、定量解析方法、元素百分含量和矿物含量求取方法,分析了全能谱分析方法中标准元素谱获取的难点和各种定量解析方法的优缺点.%Using full spectrum analysis methods, Multi-element spectrum logging single element quantum is obtained and furtherly the element weight percent and formation mineral percent are calculated. The Logging breaks a new path to distinguish lithologies and mineral types of complicated oil and gas reservoirs for building their new interpretation models and applying reasonable evaluation methods. The Logging provides a new means for resolving geological problems and engineer problems. Full spectrum analysis methods are becoming one of the study hotspots in the China now. After analyzing the important significance and research status of multi-element spectrum logging, the paper summarizes the research status, analysis steps, gaining methods of standard element spectrums, quantitative analytic methods, the obtaining methods of element content and mineral content the characteristics, and analyzes the difficulties of standard element spectrum acquirement and the merits or demerits of quantitative analytic methods for full spectrum analysis methods. The analysis and summarization show that now in China, the research on full spectrum has been placed particular emphasis on quantitative analytic methods; there is not

  11. Analysis of expression sequence tags from a full-length-enriched cDNA library of developing sesame seeds (Sesamum indicum

    Directory of Open Access Journals (Sweden)

    Ke Tao

    2011-12-01

    Full Text Available Abstract Background Sesame (Sesamum indicum is one of the most important oilseed crops with high oil contents and rich nutrient value. However, genetic improvement efforts in sesame could not get benefit from molecular biology technology due to poor DNA and RNA sequence resources. In this study, we carried out a large scale of expressed sequence tags (ESTs sequencing from developing sesame seeds and further conducted analysis on seed storage products-related genes. Results A normalized and full-length enriched cDNA library from 5 ~ 30 days old immature seeds was constructed and randomly sequenced, leading to generation of 41,248 expressed sequence tags (ESTs which then formed 4,713 contigs and 27,708 singletons with 44.9% uniESTs being putative full-length open reading frames. Approximately 26,091 of all these uniESTs have significant matches to the counterparts in Nr database of GenBank, and 21,628 of them were assigned to one or more Gene ontology (GO terms. Homologous genes involved in oil biosynthesis were identified including some conservative transcription factors regulating oil biosynthesis such as LEAFY COTYLEDON1 (LEC1, PICKLE (PKL, WRINKLED1 (WRI1 and majority of them were found for the first time in sesame seeds. One hundred and 17 ESTs were identified possibly involved in biosynthesis of sesame lignans, sesamin and sesamolin. In total, 9,347 putative functional genes from developing seeds were identified, which accounts for one third of total genes in the sesame genome. Further analysis of the uniESTs identified 1,949 non-redundant simple sequence repeats (SSRs. Conclusions This study has provided an overview of genes expressed during sesame seed development. This collection of sesame full-length cDNAs covered a wide variety of genes in seeds, in particular, candidate genes involved in biosynthesis of sesame oils and lignans. These EST sequences enriched with full length will contribute to comparative genomic studies on sesame and

  12. Development of microwave-assisted acid hydrolysis of proteins using a commercial microwave reactor and its combination with LC-MS for protein full-sequence analysis.

    Science.gov (United States)

    Chen, Lu; Wang, Nan; Li, Liang

    2014-11-01

    Microwave-assisted acid hydrolysis (MAAH) can be used to degrade a protein non-specifically into many peptides with overlapping sequences which can be identified by mass spectrometry (MS) to produce a sequence map that covers the full sequence of a protein. The success of this method for protein sequence analysis depends on the proper control of the MAAH process, which is currently done using a household microwave oven. However, to meet the regulatory or good laboratory practice (GLP) requirement in a clinical or pharmaceutical laboratory, using a commercial microwave device is often required. In this paper, we report a method of performing MAAH using a CEM Discover single-mode microwave reactor. It is shown that, using an optimized protocol for MAAH, reproducible results comparable to those obtained using a household microwave oven can be generated using the commercial reactor. To illustrate the potential applications of MAAH MS for characterizing clinically relevant proteins, this method was applied, for the first time, to map the amino acid sequences of normal and sickle-cell human hemoglobin as well as bovine hemoglobin. Full sequence coverage was readily achieved from 294 and 266 unique peptides matched to the alpha and beta subunits of normal hemoglobin, respectively, 334 and 265 unique peptides matched to the alpha and beta submit units of sickle-cell hemoglobin, and 377 and 224 unique peptides matched to the alpha and beta subunits of bovine hemoglobin. This method opens the possibility for any laboratory to use a commercial laboratory equipment to perform MAAH MS for protein full-sequence analysis.

  13. SSV3D: Simulador de Sombras Vectoriales por Radiación Solar sobre Objetos Tridimensionales SSV3D: Simulator of Vectorial Shadows by Solar Radiation on 3D Computerized Objects

    Directory of Open Access Journals (Sweden)

    S. Gómez

    2005-01-01

    Full Text Available Se presenta un simulador de sombras vectoriales por radiación solar sobre objetos tridimensionales, SSV3D, una herramienta de computación gráfica desarrollada sobre la plataforma tridimensional del AUTOCAD 2004. El software simula vectorialmente la radiación solar directa, calculando y trazando los contornos de sombra sobre los planos iluminados del modelo 3D evaluado. En el desarrollo de la herramienta se comprobaron los resultados analíticos mediante su comparación con los obtenidos en las fórmulas de una hoja de cálculo, y de los resultados gráficos mediante comparación con las sombras arrojadas por simulación con un heliodón de tecnología francesa y por el Render de AUTOCAD. El simulador SSV3D respondió satisfactoriamente a las necesidades de estudio de sistemas de protección solar en investigaciones desarrolladas anteriormente.SSV3D is presented as a graphic computer tool developed on the three-dimensional platform of AUTOCAD 2004, which simulates direct solar radiation by measuring and vectorial tracing of shadow outlines on illuminated plans of the 3D model evaluated. The analytical results of this tool were tested during its' development by comparing its' results with those obtained in the formula of a calculus sheet, and graphic results were checked comparing these to the shadows obtained by simulation using physical models in a heliodon (French technology and by the Render of AUTOCAD. The SSV3D simulator responded satisfactorily to the requirements for the study of solar protection systems which had been determined in previous research.

  14. Sequencing and analysis of full-length cDNAs, 5'-ESTs and 3'-ESTs from a cartilaginous fish, the elephant shark (Callorhinchus milii).

    KAUST Repository

    Brenner, Sydney

    2012-10-08

    Cartilaginous fishes are the most ancient group of living jawed vertebrates (gnathostomes) and are, therefore, an important reference group for understanding the evolution of vertebrates. The elephant shark (Callorhinchus milii), a holocephalan cartilaginous fish, has been identified as a model cartilaginous fish genome because of its compact genome (∼910 Mb) and a genome project has been initiated to obtain its whole genome sequence. In this study, we have generated and sequenced full-length enriched cDNA libraries of the elephant shark using the \\'oligo-capping\\' method and Sanger sequencing. A total of 6,778 full-length protein-coding cDNA and 10,701 full-length noncoding cDNA were sequenced from six tissues (gills, intestine, kidney, liver, spleen, and testis) of the elephant shark. Analysis of their polyadenylation signals showed that polyadenylation usage in elephant shark is similar to that in mammals. Furthermore, both coding and noncoding transcripts of the elephant shark use the same proportion of canonical polyadenylation sites. Besides BLASTX searches, protein-coding transcripts were annotated by Gene Ontology, InterPro domain, and KEGG pathway analyses. By comparing elephant shark genes to bony vertebrate genes, we identified several ancient genes present in elephant shark but differentially lost in tetrapods or teleosts. Only ∼6% of elephant shark noncoding cDNA showed similarity to known noncoding RNAs (ncRNAs). The rest are either highly divergent ncRNAs or novel ncRNAs. In addition to full-length transcripts, 30,375 5\\'-ESTs and 41,317 3\\'-ESTs were sequenced and annotated. The clones and transcripts generated in this study are valuable resources for annotating transcription start sites, exon-intron boundaries, and UTRs of genes in the elephant shark genome, and for the functional characterization of protein sequences. These resources will also be useful for annotating genes in other cartilaginous fishes whose genomes have been targeted for

  15. Simulation design and analysis of full adder function and application%全加器功能及应用的仿真设计分析

    Institute of Scientific and Technical Information of China (English)

    孙津平

    2011-01-01

    加法运算是数字系统中最基本的算术运算.为了能更好地利用加法器实现减法、乘法、除法、码制转换等运算,提出用Multisim虚拟仿真软件中的逻辑转换仪、字信号发生器、逻辑分析仪,时全加器进行功能仿真设计、转换、测试、分析,强化Multisim的使用,并通过用集成全加器74LS283实现两个一位8421码十进制数的减法运算,掌握了全加器的应用方法.测试证明,全加器功能的扩展和应用,利用Multisim软件的仿真设计能较好地实现.%Addition operation is the most basic digital system arithmetic. In order to achieve better use of adder subtraction ,multiplication,division ,transcoding operations ,this paper proposed using Multisim virtual simulation software ,the logic of conversion device,digital signal generator,logic analyzer,the full adder design for functional simulation,conversion,testing,analysis,and strengthened the use of Multisim and by using a full adder 74LS283 integrated to achieve a 8421 yards two decimal subtraction and master the application method of the full adder. Testing shows the expansion and application of full adder function can be well implemented by using simulation design of Multisim software.

  16. Full time-domain nonlinear coupled dynamic analysis of a truss spar and its mooring/riser system in irregular wave

    Science.gov (United States)

    Yang, MinDong; Teng, Bin; Xiao, LongFei; Ning, DeZhi; Shi, ZhongMin; Qu, Yan

    2014-01-01

    A new full time-domain nonlinear coupled method has been established and then applied to predict the responses of a Truss Spar in irregular wave. For the coupled analysis, a second-order time-domain approach is developed to calculate the wave forces, and a finite element model based on rod theory is established in three dimensions in a global coordinate system. In numerical implementation, the higher-order boundary element method (HOBEM) is employed to solve the velocity potential, and the 4th-order Adams-Bashforth-Moultn scheme is used to update the second-order wave surface. In deriving convergent solutions, the hull displacements and mooring tensions are kept consistent at the fairlead and the motion equations of platform and mooring-lines/risers are solved simultaneously using Newmark- β integration scheme including Newton-Raphson iteration. Both the coupled quasi-static analysis and the coupled dynamic analysis are performed. The numerical simulation results are also compared with the model test results, and they coincide very well as a whole. The slow-drift responses can be clearly observed in the time histories of displacements and mooring tensions. Some important characteristics of the coupled responses are concluded.

  17. Full quantitative multiple-scattering analysis of X-ray absorption spectra: application to potassium hexacyanoferrat(II) and -(III) complexes.

    Science.gov (United States)

    Hayakawa, Kuniko; Hatada, Keisuke; D'Angelo, Paola; Della Longa, Stefano; Natoli, Calogero R; Benfatto, Maurizio

    2004-12-01

    A recently developed method to the full quantitative analysis of the XAS spectra extending from the absorption edge to the high-energy region is presented. This method is based on the use of two independent approaches to the analysis of the EXAFS and XANES data, the well-known GNXAS and the newly developed MXAN procedures. Herein, we report the application of this technique to two iron complexes of known structure where multiple-scattering effects are prominent, the potassium hexacyanoferrat(II) and -(III) crystals and aqueous solutions. The structural parameters obtained from refinements using the two methods are equal and compare quite well with crystallographic values. Small discrepancies between the experimental and calculated XANES spectra have been observed, and their origin has been investigated in the framework of non-muffin-tin correction. The ligand dependence of the theoretical spectra has been also examined. Analysis of the whole energy range of the XAS spectra has been found to be useful in elucidating both the type of ligands and the geometry of iron sites. These results are of particular use in studying the geometrical environment of metallic sites in proteins and complexes of chemical interest.

  18. Model updating of a full-scale FE model with nonlinear constraint equations and sensitivity-based cluster analysis for updating parameters

    Science.gov (United States)

    Jang, Jinwoo; Smyth, Andrew W.

    2017-01-01

    The objective of structural model updating is to reduce inherent modeling errors in Finite Element (FE) models due to simplifications, idealized connections, and uncertainties of material properties. Updated FE models, which have less discrepancies with real structures, give more precise predictions of dynamic behaviors for future analyses. However, model updating becomes more difficult when applied to civil structures with a large number of structural components and complicated connections. In this paper, a full-scale FE model of a major long-span bridge has been updated for improved consistency with real measured data. Two methods are applied to improve the model updating process. The first method focuses on improving the agreement of the updated mode shapes with the measured data. A nonlinear inequality constraint equation is used to an optimization procedure, providing the capability to regulate updated mode shapes to remain within reasonable agreements with those observed. An interior point algorithm deals with nonlinearity in the objective function and constraints. The second method finds very efficient updating parameters in a more systematic way. The selection of updating parameters in FE models is essential to have a successful updating result because the parameters are directly related to the modal properties of dynamic systems. An in-depth sensitivity analysis is carried out in an effort to precisely understand the effects of physical parameters in the FE model on natural frequencies. Based on the sensitivity analysis, cluster analysis is conducted to find a very efficient set of updating parameters.

  19. Analysis of expression sequence tags from a full-length-enriched cDNA library of developing sesame seeds (Sesamum indicum).

    Science.gov (United States)

    Ke, Tao; Dong, Caihua; Mao, Han; Zhao, Yingzhong; Chen, Hong; Liu, Hongyan; Dong, Xuyan; Tong, Chaobo; Liu, Shengyi

    2011-12-24

    Sesame (Sesamum indicum) is one of the most important oilseed crops with high oil contents and rich nutrient value. However, genetic improvement efforts in sesame could not get benefit from molecular biology technology due to poor DNA and RNA sequence resources. In this study, we carried out a large scale of expressed sequence tags (ESTs) sequencing from developing sesame seeds and further conducted analysis on seed storage products-related genes. A normalized and full-length enriched cDNA library from 5 ~ 30 days old immature seeds was constructed and randomly sequenced, leading to generation of 41,248 expressed sequence tags (ESTs) which then formed 4,713 contigs and 27,708 singletons with 44.9% uniESTs being putative full-length open reading frames. Approximately 26,091 of all these uniESTs have significant matches to the counterparts in Nr database of GenBank, and 21,628 of them were assigned to one or more Gene ontology (GO) terms. Homologous genes involved in oil biosynthesis were identified including some conservative transcription factors regulating oil biosynthesis such as LEAFY COTYLEDON1 (LEC1), PICKLE (PKL), WRINKLED1 (WRI1) and majority of them were found for the first time in sesame seeds. One hundred and 17 ESTs were identified possibly involved in biosynthesis of sesame lignans, sesamin and sesamolin. In total, 9,347 putative functional genes from developing seeds were identified, which accounts for one third of total genes in the sesame genome. Further analysis of the uniESTs identified 1,949 non-redundant simple sequence repeats (SSRs). This study has provided an overview of genes expressed during sesame seed development. This collection of sesame full-length cDNAs covered a wide variety of genes in seeds, in particular, candidate genes involved in biosynthesis of sesame oils and lignans. These EST sequences enriched with full length will contribute to comparative genomic studies on sesame and other oilseed plants and serve as an abundant

  20. Socioeconomic disparities in coverage of full immunisation among children of adolescent mothers in India, 1990–2006: a repeated cross-sectional analysis

    Science.gov (United States)

    Kumar, Chandan; Singh, Prashant Kumar; Singh, Lucky; Rai, Rajesh Kumar

    2016-01-01

    Objective Studies have highlighted that children of adolescent (aged 15–19 years) mothers are likely to receive relatively poor healthcare. With an unacceptably high adolescent birth rate, India houses the highest number of adolescent mothers globally, putting children at risk of inadequate vaccination. This paper assesses trends and extent of socioeconomic disparities in the coverage of full immunisation among children of adolescent mothers in India. Design Repeated cross-sectional analytical study. Data sources 3 consecutive rounds of the National Family Health Survey (NFHS) conducted during 1992–1993, 1998–1999 and 2005–2006 were used. Besides, the required information is also extracted from the 2011 Indian Census. Participants Children (aged 12–23 months) of adolescent (aged 15–19 years) mothers. Sample inclusion criteria involved the last child of the adolescent eligible to avail full immunisation. Setting Nationally representative sample. Data analysis The Cochran-Armitage test, χ2 test and binary logistic regression methods were applied to attain the study objective. Results Between 1990 and 2006, a non-significant increase of 4 percentage points in full immunisation of children of adolescent mothers was estimated. During the same period, a large difference between the probability of children of adolescent mothers receiving full immunisation belonging to the least (predicted probability (PP): 0.196 in 1990–1993, and PP: 0.213 in 2003–2006) and the most (PP: 0.589 in 1990–1993, and PP: 0.645 in 2003–2006) socioeconomically privileged group was estimated, and this disparity persisted over the survey period. Conclusions During 1990–2006, an insufficient improvement in provision of full immunisation to children born to adolescent mothers was recorded. The study underscored the suboptimum immunisation of rural, illiterate and poor children of adolescent women. The programme and policymakers could focus on district-wise concentration

  1. Combined-cycle power stations using ``clean-coal-technologies``: Thermodynamic analysis of full gasification vs. fluidized bed combustion with partial gasification

    Energy Technology Data Exchange (ETDEWEB)

    Lozza, G.; Chiesa, P. [Politecnico di Milano, Milan (Italy). Dept. of Energetics; DeVita, L. [Eniricerche, Milan (Italy)

    1994-12-31

    A novel class of power plants for clean conversion of coal into power has been recently proposed, based on the concept of partial coal gasification and fluidized-bed combustion of unconverted char from gasification. This paper focuses on the thermodynamic aspects of these plants, in comparison with full gasification cycles, assessing their performance on the basis of a common advanced power plant technology level. Several plant configurations are considered, including pressurized or atmospheric fluidized-bed, air- or steam-cooled, with different carbon conversion in the gasifier. The calculation method, used for reproducing plant energy balances and for performance prediction, is described in the paper. A complete second-law analysis is carried out, pointing out the efficiency loss breakdown for both technologies. Results show that partial gasification plants can achieve efficiencies consistently higher than IGCC, depending on plant configuration and carbon conversion, making this solution a viable and attractive option for efficient coal utilization.

  2. Combined-cycle power stations using clean-coal technologies: Thermodynamic analysis of full gasification versus fluidized bed combustion with partial gasification

    Energy Technology Data Exchange (ETDEWEB)

    Lozza, G.; Chiesa, P. [Politecnico di Milano, Milan (Italy). Dept. of Energetics; DeVita, L. [Eniricerche, Milan (Italy)

    1996-10-01

    A novel class of power plants for clean conversion of coal into power has been recently proposed, based on the concept of partial coal gasification and fluidized-bed combustion of unconverted char from gasification. This paper focuses on the thermodynamic aspects of these plants, in comparison with full gasification cycles, assessing their performance on the basis of a common advanced power plant technology level. Several plant configurations are considered, including pressurized or atmospheric fluidized-bed, air- or steam-cooled, with different carbon conversion in the gasifier. The calculation method, used for reproducing plant energy balances and for performance prediction, is described in the paper. A complete second-law analysis is carried out, pointing out the efficiency loss breakdown for both technologies. Results show that partial gasification plants can achieve efficiencies consistently higher than IGCC, depending on plant configuration and carbon conversion, making this solution a viable and attractive option for efficient coal utilization.

  3. Quantification method of N2O emission from full-scale biological nutrient removal wastewater treatment plant by laboratory batch reactor analysis.

    Science.gov (United States)

    Lim, Yesul; Kim, Dong-Jin

    2014-08-01

    This study proposes a simplified method for the quantification of N2O emission from a biological nutrient removal wastewater treatment plant (WWTP). The method incorporates a laboratory-scale batch reactor which had almost the same operational (wastewater and sludge flow rates) condition of a unit operation/process of the WWTP. Cumulative N2O emissions from the batch reactor at the corresponding hydraulic retention times of the full-scale units (primary and secondary clarifiers, pre-anoxic, anaerobic, anoxic and aerobic basins) were used for the quantification of N2O emission. The analysis showed that the aerobic basin emitted 95% of the total emission and the emission factor (yield) reached 0.8% based on the influent nitrogen load. The method successfully estimated N2O emission from the WWTP and it has shown advantages in measurement time and cost over the direct field measurement (floating chamber) method. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Multi-scale Full-orbit Analysis on Phase-space Behavior of Runaway Electrons in Tokamak Fields with Synchrotron Radiation

    CERN Document Server

    Wang, Yulei; Liu, Jian

    2016-01-01

    In this paper, the secular full-orbit simulations of runaway electrons with synchrotron radiation in tokamak fields are carried out using a relativistic volume-preserving algorithm. Detailed phase-space behaviors of runaway electrons are investigated in different dynamical timescales spanning 11 orders. When looking into the small timescale, i.e., the characteristic timescale imposed by Lorentz force, the severely deformed helical trajectory of energetic runaway electron is witnessed. A qualitative analysis of the neoclassical scattering, a kind of collisionless pitch-angle scattering phenomena, is provided when considering the coupling between the rotation of momentum vector and the background magnetic field. In large timescale up to one second, it is found that the initial condition of runaway electrons in phase space globally influences the pitch-angle scattering, the momentum evolution, and the loss-gain ratio of runaway energy evidently. However, the initial value has little impact on the synchrotron ene...

  5. Recurrence of occult hepatitis B virus infection in a recipient of a liver transplant for HCV-related cirrhosis: full length genome, mutations analysis and literature review

    Directory of Open Access Journals (Sweden)

    Tahar Bajjou

    2014-08-01

    Full Text Available The outcome of liver transplant recipients in HCV chronic carriers with Anti-HBc only concerning occult HBV infection is unknown. We report here the case of a patient who underwent liver transplantation (LT for cirrhosis post chronic hepatitis C who received an allograft from a donor with no marker of hepatitis B infection. After LT, HBV DNA was detected in the serum in the absence of HBsAg while HCV RNA remained negative. To determine the origin of this occult HBV infection, we retrospectively examined stored serum and liver tissue, pre and post-transplantation, for HBV DNA by PCR. A stored liver biopsy of the donor before transplantation was also tested. HBV DNA was detected in the pre-transplant liver but not in the donor liver. HBV viral load quantified by real time PCR after LT ranged from about 102 to 5x103 HBV DNA copies/mg of liver, while in sera, concentrations ranged from 102 to 3x103 HBV DNA copies/ml. All PCR products in the S gene from liver and sera were sequenced. Analysis of sequences showed the presence of an HBV strain genotype D. The nucleotide homology between the patient's HBV strains before and after LT was 96 % across the analyzed regions. Full length HBV genomes were amplified from the sera using Rolling Circle Amplification and then sequenced. Analysis of sequences confirmed the genotype D, but did not show obvious mutations that could contribute to HBsAg seronegativity and low HBV viral replication. Factors leading to occult HBV infection are still unclear, but it is well establish that occult HBV infection is frequent in HCV patients. This underlines the role of extra hepatic sites for HBV replication, potentially lymphocytes acting as and ldquo;reservoirs and rdquo;. [Int J Res Med Sci 2014; 2(4.000: 1294-1301

  6. Study of canine parvovirus evolution: comparative analysis of full-length VP2 gene sequences from Argentina and international field strains.

    Science.gov (United States)

    Gallo Calderón, Marina; Wilda, Maximiliano; Boado, Lorena; Keller, Leticia; Malirat, Viviana; Iglesias, Marcela; Mattion, Nora; La Torre, Jose

    2012-02-01

    The continuous emergence of new strains of canine parvovirus (CPV), poorly protected by current vaccination, is a concern among breeders, veterinarians, and dog owners around the world. Therefore, the understanding of the genetic variation in emerging CPV strains is crucial for the design of disease control strategies, including vaccines. In this paper, we obtained the sequences of the full-length gene encoding for the main capsid protein (VP2) of 11 canine parvovirus type 2 (CPV-2) Argentine representative field strains, selected from a total of 75 positive samples studied in our laboratory in the last 9 years. A comparative sequence analysis was performed on 9 CPV-2c, one CPV-2a, and one CPV-2b Argentine strains with respect to international strains reported in the GenBank database. In agreement with previous reports, a high degree of identity was found among CPV-2c Argentine strains (99.6-100% and 99.7-100% at nucleotide and amino acid levels, respectively). However, the appearance of a new substitution in the 440 position (T440A) in four CPV-2c Argentine strains obtained after the year 2009 gives support to the variability observed for this position located within the VP2, three-fold spike. This is the first report on the genetic characterization of the full-length VP2 gene of emerging CPV strains in South America and shows that all the Argentine CPV-2c isolates cluster together with European and North American CPV-2c strains.

  7. A time-course analysis of four full-scale anaerobic digesters in relation to the dynamics of change of their microbial communities.

    Science.gov (United States)

    Pycke, B F G; Etchebehere, C; Van de Caveye, P; Negroni, A; Verstraete, W; Boon, N

    2011-01-01

    This study describes the microbial community richness, -dynamics, and -organization of four full-scale anaerobic digesters during a time-course study of 45 days. The microbial community was analyzed using a Bacteria- and Archaea-targeting 16S rRNA gene-based Terminal-Restriction Fragment Length Polymorphism approach. Clustering analysis separated meso- and thermophilic reactors for both archaeal and bacterial communities. Regardless of the operating temperature, each installation possessed a distinct community profile. For both microbial domains, about 8 dominant terminal-restriction fragments could be observed, with a minimum of 4 and a maximum of 14. The bacterial community organization (a coefficient which describes the specific degree of evenness) showed a factor 2 more variation in the mesophilic reactors, compared with the thermophilic ones. The archaeal community structure of the mesophilic UASB reactor was found to be more stable. The community composition was highly dynamic for Bacteria and Archaea, with a rate of change between 20-50% per 15 days. This study illustrated that microbial communities in full-scale anaerobic digesters are unique to the installation and that community properties are dynamic. Converging complex microbial processes such as anaerobic digestion which rely on a multitude of microbial teams apparently can be highly dynamic.

  8. Comparative Analysis of Semiconductor Power Losses of Galvanically Isolated Quasi-Z-Source and Full-Bridge Boost DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Kosenko Roman

    2015-07-01

    Full Text Available This paper compares semiconductor losses of the galvanically isolated quasi-Z-source converter and full-bridge boost DC-DC converter with active clamping circuit. Operation principle of both converters is described. Short design guidelines are provided as well. Results of steady state analysis are used to calculate semiconductor power losses for both converters. Analytical expressions are derived for all types of semiconductor power losses present in these converters. The theoretical results were verified by means of numerical simulation performed in the PSIM simulation software. Its add-on module “Thermal module” was used to estimate semiconductor power losses using the datasheet parameters of the selected semiconductor devices. Results of calculations and simulation study were obtained for four operating points with different input voltage and constant input current to compare performance of the converters in renewable applications, like photovoltaic, where input voltage and power can vary significantly. Power loss breakdown is detailed and its dependence on the converter output power is analyzed. Recommendations are given for the use of the converter topologies in applications with low input voltage and relatively high input current.

  9. Proteome analysis of liver cells expressing a full-length hepatitis C virus (HCV) replicon and biopsy specimens of posttransplantation liver from HCV-infected patients.

    Science.gov (United States)

    Jacobs, Jon M; Diamond, Deborah L; Chan, Eric Y; Gritsenko, Marina A; Qian, Weijun; Stastna, Miroslava; Baas, Tracey; Camp, David G; Carithers, Robert L; Smith, Richard D; Katze, Michael G

    2005-06-01

    The development of a reproducible model system for the study of hepatitis C virus (HCV) infection has the potential to significantly enhance the study of virus-host interactions and provide future direction for modeling the pathogenesis of HCV. While there are studies describing global gene expression changes associated with HCV infection, changes in the proteome have not been characterized. We report the first large-scale proteome analysis of the highly permissive Huh-7.5 cell line containing a full-length HCV replicon. We detected >4,200 proteins in this cell line, including HCV replicon proteins, using multidimensional liquid chromatographic (LC) separations coupled to mass spectrometry. Consistent with the literature, a comparison of HCV replicon-positive and -negative Huh-7.5 cells identified expression changes of proteins involved in lipid metabolism. We extended these analyses to liver biopsy material from HCV-infected patients where a total of >1,500 proteins were detected from only 2 mug of liver biopsy protein digest using the Huh-7.5 protein database and the accurate mass and time tag strategy. These findings demonstrate the utility of multidimensional proteome analysis of the HCV replicon model system for assisting in the determination of proteins/pathways affected by HCV infection. Our ability to extend these analyses to the highly complex proteome of small liver biopsies with limiting protein yields offers the unique opportunity to begin evaluating the clinical significance of protein expression changes associated with HCV infection.

  10. The Constitution Analysis of Coal Production full Cost%煤炭完全生产成本的构成分析

    Institute of Scientific and Technical Information of China (English)

    于跃峰; 张永财; 张帆

    2013-01-01

      通过对我国煤炭企业成本核算现状及煤炭企业成本核算体系中存在问题的分析,说明分析煤炭完全生产成本构成的重要性。煤炭完全生产成本应该包括资源成本、基本生产成本、生态环境成本、安全成本以及可持续发展成本等,并对各自的构成作了详细的分析。最后通过实例分析,说明煤炭行业不是暴利行业,得出为了全面完整的反映煤炭的真实价值,应该增加生态环境成本、安全成本,资源成本等的结论。%Through the analysis of the status quo of Chinese coal enterprises' cost accounting and the existing problems in cost accounting sys-tem,this paper points out the importance of analyzing the full coal cost. The full cost should include resource cost , basal procuction cost,safety cost,environmental cost and continuable development cost etc. And their own constitution are analyzed in detail. Finally, this paper makes clear that coal enterprises cann't rake in exorbitant profits by analyzing a practical case and draw a conclusion that we should increase envi-ronmental cost,safety cost and resource cost to reflect the truly value of coal fully and completely.

  11. A full quantum analysis of the Stern–Gerlach experiment using the evolution operator method: analyzing current issues in teaching quantum mechanics

    Science.gov (United States)

    Benítez Rodríguez, E.; Arévalo Aguilar, L. M.; Piceno Martínez, E.

    2017-03-01

    To the quantum mechanics specialists community it is a well-known fact that the famous original Stern–Gerlach experiment (SGE) produces entanglement between the external degrees of freedom (position) and the internal degree of freedom (spin) of silver atoms. Despite this fact, almost all textbooks on quantum mechanics explain this experiment using a semiclassical approach, where the external degrees of freedom are considered classical variables, the internal degree is treated as a quantum variable, and Newton's second law is used to describe the dynamics. In the literature there are some works that analyze this experiment in its full quantum mechanical form. However, astonishingly, to the best of our knowledge the original experiment, where the initial states of the spin degree of freedom are randomly oriented coming from the oven, has not been analyzed yet in the available textbooks using the Schrödinger equation (to the best of our knowledge there is only one paper that treats this case: Hsu et al (2011 Phys. Rev. A 83 012109)). Therefore, in this contribution we use the time-evolution operator to give a full quantum mechanics analysis of the SGE when the initial state of the internal degree of freedom is completely random, i.e. when it is a statistical mixture. Additionally, as the SGE and the development of quantum mechanics are heavily intermingled, we analyze some features and drawbacks in the current teaching of quantum mechanics. We focus on textbooks that use the SGE as a starting point, based on the fact that most physicist do not use results from physics education research, and comment on traditional pedagogical attitudes in the physics community.

  12. Large-scale analysis of full-length cDNAs from the tomato (Solanum lycopersicum) cultivar Micro-Tom, a reference system for the Solanaceae genomics.

    Science.gov (United States)

    Aoki, Koh; Yano, Kentaro; Suzuki, Ayako; Kawamura, Shingo; Sakurai, Nozomu; Suda, Kunihiro; Kurabayashi, Atsushi; Suzuki, Tatsuya; Tsugane, Taneaki; Watanabe, Manabu; Ooga, Kazuhide; Torii, Maiko; Narita, Takanori; Shin-I, Tadasu; Kohara, Yuji; Yamamoto, Naoki; Takahashi, Hideki; Watanabe, Yuichiro; Egusa, Mayumi; Kodama, Motoichiro; Ichinose, Yuki; Kikuchi, Mari; Fukushima, Sumire; Okabe, Akiko; Arie, Tsutomu; Sato, Yuko; Yazawa, Katsumi; Satoh, Shinobu; Omura, Toshikazu; Ezura, Hiroshi; Shibata, Daisuke

    2010-03-30

    The Solanaceae family includes several economically important vegetable crops. The tomato (Solanum lycopersicum) is regarded as a model plant of the Solanaceae family. Recently, a number of tomato resources have been developed in parallel with the ongoing tomato genome sequencing project. In particular, a miniature cultivar, Micro-Tom, is regarded as a model system in tomato genomics, and a number of genomics resources in the Micro-Tom-background, such as ESTs and mutagenized lines, have been established by an international alliance. To accelerate the progress in tomato genomics, we developed a collection of fully-sequenced 13,227 Micro-Tom full-length cDNAs. By checking redundant sequences, coding sequences, and chimeric sequences, a set of 11,502 non-redundant full-length cDNAs (nrFLcDNAs) was generated. Analysis of untranslated regions demonstrated that tomato has longer 5'- and 3'-untranslated regions than most other plants but rice. Classification of functions of proteins predicted from the coding sequences demonstrated that nrFLcDNAs covered a broad range of functions. A comparison of nrFLcDNAs with genes of sixteen plants facilitated the identification of tomato genes that are not found in other plants, most of which did not have known protein domains. Mapping of the nrFLcDNAs onto currently available tomato genome sequences facilitated prediction of exon-intron structure. Introns of tomato genes were longer than those of Arabidopsis and rice. According to a comparison of exon sequences between the nrFLcDNAs and the tomato genome sequences, the frequency of nucleotide mismatch in exons between Micro-Tom and the genome-sequencing cultivar (Heinz 1706) was estimated to be 0.061%. The collection of Micro-Tom nrFLcDNAs generated in this study will serve as a valuable genomic tool for plant biologists to bridge the gap between basic and applied studies. The nrFLcDNA sequences will help annotation of the tomato whole-genome sequence and aid in tomato functional

  13. Probiotics and Time to Achieve Full Enteral Feeding in Human Milk-Fed and Formula-Fed Preterm Infants: Systematic Review and Meta-Analysis.

    Science.gov (United States)

    Aceti, Arianna; Gori, Davide; Barone, Giovanni; Callegari, Maria Luisa; Fantini, Maria Pia; Indrio, Flavia; Maggio, Luca; Meneghin, Fabio; Morelli, Lorenzo; Zuccotti, Gianvincenzo; Corvaglia, Luigi

    2016-07-30

    Probiotics have been linked to a reduction in the incidence of necrotizing enterocolitis and late-onset sepsis in preterm infants. Recently, probiotics have also proved to reduce time to achieve full enteral feeding (FEF). However, the relationship between FEF achievement and type of feeding in infants treated with probiotics has not been explored yet. The aim of this systematic review and meta-analysis was to evaluate the effect of probiotics in reducing time to achieve FEF in preterm infants, according to type of feeding (exclusive human milk (HM) vs. formula). Randomized-controlled trials involving preterm infants receiving probiotics, and reporting on time to reach FEF were included in the systematic review. Trials reporting on outcome according to type of feeding (exclusive HM vs. formula) were included in the meta-analysis. Fixed-effect or random-effects models were used as appropriate. Results were expressed as mean difference (MD) with 95% confidence interval (CI). Twenty-five studies were included in the systematic review. In the five studies recruiting exclusively HM-fed preterm infants, those treated with probiotics reached FEF approximately 3 days before controls (MD -3.15 days (95% CI -5.25/-1.05), p = 0.003). None of the two studies reporting on exclusively formula-fed infants showed any difference between infants receiving probiotics and controls in terms of FEF achievement. The limited number of included studies did not allow testing for other subgroup differences between HM and formula-fed infants. However, if confirmed in further studies, the 3-days reduction in time to achieve FEF in exclusively HM-fed preterm infants might have significant implications for their clinical management.

  14. Understanding repeated non-attendance in health services: a pilot analysis of administrative data and full study protocol for a national retrospective cohort

    Science.gov (United States)

    Williamson, Andrea E; Ellis, David A; Wilson, Philip; McQueenie, Ross; McConnachie, Alex

    2017-01-01

    Introduction Understanding the causes of low engagement in healthcare is a pre-requisite for improving health services’ contribution to tackling health inequalities. Low engagement includes missing healthcare appointments. Serially (having a pattern of) missing general practice (GP) appointments may provide a risk marker for vulnerability and poorer health outcomes. Methods and analysis A proof of concept pilot using GP appointment data and a focus group with GPs informed the development of missed appointment categories: patients can be classified based on the number of appointments missed each year. The full study, using a retrospective cohort design, will link routine health service and education data to determine the relationship between GP appointment attendance, health outcomes, healthcare usage, preventive health activity and social circumstances taking a life course approach and using data from the whole journey in the National Health Service (NHS) healthcare. 172 practices will be recruited (∼900 000 patients) across Scotland. The statistical analysis will focus on 2 key areas: factors that predict patients who serially miss appointments, and serial missed appointments as a predictor of future patient outcomes. Regression models will help understand how missed appointment patterns are associated with patient and practice characteristics. We shall identify key factors associated with serial missed appointments and potential interactions that might predict them. Ethics and dissemination The results of the project will inform debates concerning how best to reduce non-attendance and increase patient engagement within healthcare systems. Significant non-academic beneficiaries include governments, policymakers and medical practitioners. Results will be disseminated via a combination of academic outputs (papers, conferences), social media and through collaborative public health/policy fora. PMID:28196951

  15. Proteome Analysis of Liver Cells Expressing a Full- Length Hepatitis C Virus (HCV) Replicon and Biopsy Specimens of Posttransplantation Liver from HCV-Infected Patients

    Energy Technology Data Exchange (ETDEWEB)

    Jacobs, Jon M.; Diamond, Deborah L.; Chan, Eric Y.; Gritsenko, Marina A.; Qian, Weijun; Stastna, Miroslava; Baas, Tracey; Camp, David G.; Carithers, Jr., Robert L.; Smith, Richard D.; Katze, Michael G.

    2005-06-01

    The development of a reproducible model system for the study of Hepatitis C virus (HCV) infection has the potential to significantly enhance the study of virus-host interactions and provide future direction for modeling the pathogenesis of HCV. While there are studies describing global gene expression changes associated with HCV infection, changes in the proteome have not been characterized. We report the first large scale proteome analysis of the highly permissive Huh-7.5 cell line containing a full length HCV replicon. We detected > 4,400 proteins in this cell line, including HCV replicon proteins, using multidimensional liquid chromatographic (LC) separations coupled to mass spectrometry (MS). The set of Huh-7.5 proteins confidently identified is, to our knowledge, the most comprehensive yet reported for a human cell line. Consistent with the literature, a comparison of Huh-7.5 cells (+) and (-) the HCV replicon identified expression changes of proteins involved in lipid metabolism. We extended these analyses to liver biopsy material from HCV-infected patients where > 1,500 proteins were detected from 2 {micro}g protein lysate using the Huh-7.5 protein database and the accurate mass and time (AMT) tag strategy. These findings demonstrate the utility of multidimensional proteome analysis of the HCV replicon model system for assisting the determination of proteins/pathways affected by HCV infection. Our ability to extend these analyses to the highly complex proteome of small liver biopsies with limiting protein yields offers the unique opportunity to begin evaluating the clinical significance of protein expression changes associated with HCV infection.

  16. First Isolation of New Canine Parvovirus 2a from Tibetan Mastiff and Global Analysis of the Full-Length VP2 Gene of Canine Parvoviruses 2 in China

    Directory of Open Access Journals (Sweden)

    Zhijun Zhong

    2014-07-01

    Full Text Available Canine parvovirus 2 (CPV-2 was first identified in 1978, and is responsible for classic parvoviral enteritis. Despite the widespread vaccination of domestic carnivores, CPVs have remained important pathogens of domestic and wild carnivores. In this study, we isolated CPV-2 from Tibetan mastiffs and performed a global analysis of the complete VP2 gene sequences of CPV-2 strains in China. Six isolates were typed as new CPV-2a, according to key amino acid positions. On a phylogenetic tree, these six sequences formed a distinct clade. Five isolates occurred on the same branch as KF785794 from China and GQ379049 from Thailand; CPV-LS-ZA1 formed a separate subgroup with FJ435347 from China. One hundred ninety-eight sequences from various parts of China and the six sequences isolated here formed seven distinct clusters, indicating the high diversity of CPVs in China. Of 204 VP2 sequences, 183 (91.04% encoded the mutation Ser297Ala, regardless of the antigenic type, implying that most Chinese CPV-2 strains contain the VP2 mutation Ser297Ala. However, the biological significance of this change from prototype CPV-2a/2b to new CPV-2a/2b types remains unclear. This study is the first to isolate new CPV-2a from the Tibetan mastiff. Our data show that new CPV-2a/2b variants are now circulating in China.

  17. Analysis of the Unsteady Flow Field in a Centrifugal Compressor from Peak Efficiency to Near Stall with Full-Annulus Simulations

    Directory of Open Access Journals (Sweden)

    Yannick Bousquet

    2014-01-01

    Full Text Available This study concerns a 2.5 pressure ratio centrifugal compressor stage consisting of a splittered unshrouded impeller and a vaned diffuser. The aim of this paper is to investigate the modifications of the flow structure when the operating point moves from peak efficiency to near stall. The investigations are based on the results of unsteady three-dimensional simulations, in a calculation domain comprising all the blade. A detailed analysis is given in the impeller inducer and in the vaned diffuser entry region through time-averaged and unsteady flow field. In the impeller inducer, this study demonstrates that the mass flow reduction from peak efficiency to near stall leads to intensification of the secondary flow effects. The low momentum fluid accumulated near the shroud interacts with the main flow through a shear layer zone. At near stall condition, the interface between the two flow structures becomes unstable leading to vortices development. In the diffuser entry region, by reducing the mass flow, the high incidence angle from the impeller exit induces a separation on the diffuser vane suction side. At near stall operating point, vorticity from the separation is shed into vortex cores which are periodically formed and convected downstream along the suction side.

  18. Advanced organic and biological analysis of dual media filtration used as a pretreatment in a full-scale seawater desalination plant

    KAUST Repository

    Jeong, Sanghyun

    2016-02-19

    Dual media filter (DMF) is being used as a primary pretreatment to remove particulate foulants at seawater desalination plants. However, many plants experience organic and biological fouling. The first part of this paper focuses on the monitoring of organic and biological foulants using advanced analytical techniques to optimize functioning of DMF at Perth Seawater Desalination Plant (PSDP) in Western Australia. In addition, microbial community analysis in DMF filtered seawater, and on DMF media (DMF-M) and cartridge filter (CF) was conducted using terminal restriction fragment length polymorphism (T-RFLP) and 454-pyrosequencing. In the full-scale DMF system, the bacterial community structure was clustered along with the filtration time and sampling positions. For the DMF effluent samples, the bacterial community structure significantly shifted after 4 h of filtration time, which corresponded with the permeability reduction trend. The dominant bacterial communities in the DMF effluent were OTU 13 (Phaeobacter) and OTU 19 (Oceaniserpentilla). The different biofilm-forming bacteria communities were found in the biofilm samples on DMF-M and CF. In the second part of the study, semi-pilot scale DMF columns were operated on-site under same operating conditions used in PSDP. It demonstrated the advantage of operating DMF at the biofiltration mode for improving the reduction of biofoulants. © 2016 Elsevier B.V.

  19. The Analysis of Near Full-Length Genome Sequences of HIV Type 1 Subtype A Viruses from Russia Supports the Monophyly of Major Intrasubtype Clusters

    Science.gov (United States)

    Fernández-García, Aurora; Revilla, Ana; Vázquez-de Parga, Elena; Vinogradova, Anna; Rakhmanova, Aza; Karamov, Eduard; Carrera, Cristina; Delgado, Elena; Pérez-Álvarez, Lucía; Nájera, Rafael; Osmanov, Saladin

    2012-01-01

    Abstract The HIV-1 epidemic in Russia has been insufficiently studied, with only 11 complete genome sequences from this country currently available, only three of which are of the locally predominant genetic form, the former Soviet Union (FSU) subtype A variant (AFSU). Here we analyze 10 newly derived AFSU near full-length genome sequences from Russia. Samples were selected based on phylogenetic clustering in protease-reverse transcriptase in two of the major AFSU clusters, V77IPR (n=6), widely circulating in Russia and other FSU countries, and ASP1 (n=4), predominant in St. Petersburg. The phylogenetic analysis shows that the V77IPR genomes group in a monophyletic cluster together with 10 previously obtained AFSU genome sequences from Uzbekistan, Kazakhstan, Russia, and Cyprus, all bearing the V77I substitution in protease. Similarly, the four ASP1 genomes group in a monophyletic cluster. These results therefore show that the monophyly of V77IPR and ASP1 AFSU clusters is supported in near complete genomes. PMID:22251084

  20. Full-length genome characterization and genetic relatedness analysis of hepatitis A virus outbreak strains associated with acute liver failure among children.

    Science.gov (United States)

    Vaughan, Gilberto; Forbi, Joseph C; Xia, Guo-Liang; Fonseca-Ford, Maureen; Vazquez, Roberto; Khudyakov, Yury E; Montiel, Sonia; Waterman, Steve; Alpuche, Celia; Gonçalves Rossi, Livia Maria; Luna, Norma

    2014-02-01

    Clinical infection by hepatitis A virus (HAV) is generally self-limited but in some cases can progress to liver failure. Here, an HAV outbreak investigation among children with acute liver failure in a highly endemic country is presented. In addition, a sensitive method for HAV whole genome amplification and sequencing suitable for analysis of clinical samples is described. In this setting, two fatal cases attributed to acute liver failure and two asymptomatic cases living in the same household were identified. In a second household, one HAV case was observed with jaundice which resolved spontaneously. Partial molecular characterization showed that both households were infected by HAV subtype IA; however, the infecting strains in the two households were different. The HAV outbreak strains recovered from all cases grouped together within cluster IA1, which contains closely related HAV strains from the United States commonly associated with international travelers. Full-genome HAV sequences obtained from the household with the acute liver failure cases were related (genetic distances ranging from 0.01% to 0.04%), indicating a common-source infection. Interestingly, the strain recovered from the asymptomatic household contact was nearly identical to the strain causing acute liver failure. The whole genome sequence from the case in the second household was distinctly different from the strains associated with acute liver failure. Thus, infection with almost identical HAV strains resulted in drastically different clinical outcomes.

  1. Full likelihood analysis of genetic risk with variable age at onset disease--combining population-based registry data and demographic information.

    Directory of Open Access Journals (Sweden)

    Janne Pitkäniemi

    Full Text Available BACKGROUND: In genetic studies of rare complex diseases it is common to ascertain familial data from population based registries through all incident cases diagnosed during a pre-defined enrollment period. Such an ascertainment procedure is typically taken into account in the statistical analysis of the familial data by constructing either a retrospective or prospective likelihood expression, which conditions on the ascertainment event. Both of these approaches lead to a substantial loss of valuable data. METHODOLOGY AND FINDINGS: Here we consider instead the possibilities provided by a Bayesian approach to risk analysis, which also incorporates the ascertainment procedure and reference information concerning the genetic composition of the target population to the considered statistical model. Furthermore, the proposed Bayesian hierarchical survival model does not require the considered genotype or haplotype effects be expressed as functions of corresponding allelic effects. Our modeling strategy is illustrated by a risk analysis of type 1 diabetes mellitus (T1D in the Finnish population-based on the HLA-A, HLA-B and DRB1 human leucocyte antigen (HLA information available for both ascertained sibships and a large number of unrelated individuals from the Finnish bone marrow donor registry. The heterozygous genotype DR3/DR4 at the DRB1 locus was associated with the lowest predictive probability of T1D free survival to the age of 15, the estimate being 0.936 (0.926; 0.945 95% credible interval compared to the average population T1D free survival probability of 0.995. SIGNIFICANCE: The proposed statistical method can be modified to other population-based family data ascertained from a disease registry provided that the ascertainment process is well documented, and that external information concerning the sizes of birth cohorts and a suitable reference sample are available. We confirm the earlier findings from the same data concerning the HLA-DR3

  2. Un reporte de la investigación: construcción cognitiva de los conceptos espacio vectorial R2 y R3 desde la teoría apoe

    OpenAIRE

    Rodríguez, Miguel; Parraguez, Marcela

    2013-01-01

    El presente artículo da cuenta de la primera etapa de nuestra investigación en curso, esto es, una construcción cognitiva llamada descomposición genética para los conceptos matemáticos espacio vectorial R2 y R3 y, su respectivo tránsito. La indagación que hacemos de las ideas en torno al concepto espacio vectorial se sitúa en el marco teórico y metodológico que sustenta esta investigación, –la teoría APOE–. Como resultado de esta etapa, presentamos una descomposición genética hipotética y la ...

  3. Dose-Volume Analysis of Predictors for Gastrointestinal Toxicity After Concurrent Full-Dose Gemcitabine and Radiotherapy for Locally Advanced Pancreatic Adenocarcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Huang Jiayi [Department of Radiation Oncology, William Beaumont Hospital, Royal Oak, MI (United States); Robertson, John M., E-mail: jrobertson@beaumont.edu [Department of Radiation Oncology, William Beaumont Hospital, Royal Oak, MI (United States); Ye Hong [Department of Radiation Oncology, William Beaumont Hospital, Royal Oak, MI (United States); Margolis, Jeffrey; Nadeau, Laura [Division of Medical Oncology, William Beaumont Hospital, Royal Oak, MI (United States); Yan Di [Department of Radiation Oncology, William Beaumont Hospital, Royal Oak, MI (United States)

    2012-07-15

    Purpose: To identify dosimetric predictors for the development of gastrointestinal (GI) toxicity in patients with locally advanced pancreatic adenocarcinoma (LAPC) treated with concurrent full-dose gemcitabine and radiotherapy (GemRT). Methods and Materials: From June 2002 to June 2009, 46 LAPC patients treated with definitive GemRT were retrospectively analyzed. The stomach and duodenum were retrospectively contoured separately to determine their dose-volume histogram (DVH) parameters. GI toxicity was defined as Grade 3 or higher GI toxicity. The follow-up time was calculated from the start of RT to the date of death or last contact. Univariate analysis (UVA) and multivariate analysis (MVA) using Kaplan-Meier and Cox regression models were performed to identify risk factors associated with GI toxicity. The receiver operating characteristic curve and the area under the receiver operating characteristic curve (AUC) were used to determine the best DVH parameter to predict for GI toxicity. Results: Of the patients, 28 (61%) received concurrent gemcitabine alone, and 18 (39%) had concurrent gemcitabine with daily erlotinib. On UVA, only the V{sub 20Gy} to V{sub 35Gy} of duodenum were significantly associated with GI toxicity (all p {<=} 0.05). On MVA, the V{sub 25Gy} of duodenum and the use of erlotinib were independent risk factors for GI toxicity (p = 0.006 and 0.02, respectively). For the entire cohort, the V{sub 25Gy} of duodenum is the best predictor for GI toxicity (AUC = 0.717), and the 12-month GI toxicity rate was 8% vs. 48% for V{sub 25Gy} {<=} 45% and V{sub 25Gy} > 45%, respectively (p = 0.03). However, excluding the erlotinib group, the V{sub 35Gy} is the best predictor (AUC = 0.725), and the 12-month GI toxicity rate was 0% vs. 41% for V{sub 35Gy} {<=} 20% and V{sub 35Gy} > 20%, respectively (p = 0.04). Conclusions: DVH parameters of duodenum may predict Grade 3 GI toxicity after GemRT for LAPC. Concurrent use of erlotinib during GemRT may increase GI

  4. Evaluation of caregiver-friendly workplace policy (CFWPs) interventions on the health of full-time caregiver employees (CEs): implementation and cost-benefit analysis.

    Science.gov (United States)

    Williams, Allison M; Tompa, Emile; Lero, Donna S; Fast, Janet; Yazdani, Amin; Zeytinoglu, Isik U

    2017-09-20

    Current Canadian evidence illustrating the health benefits and cost-effectiveness of caregiver-friendly workplace policies is needed if Canadian employers are to adopt and integrate caregiver-friendly workplace policies into their employment practices. The goal of this three-year, three study research project is to provide such evidence for the auto manufacturing and educational services sectors. The research questions being addressed are: What are the impacts for employers (economic) and workers (health) of caregiver-friendly workplace policy intervention(s) for full-time caregiver-employees? What are the impacts for employers, workers and society of the caregiver-friendly workplace policy intervention(s) in each participating workplace? What contextual factors impact the successful implementation of caregiver-friendly workplace policy intervention(s)? Using a pre-post-test comparative case study design, Study A will determine the effectiveness of newly implemented caregiver-friendly workplace policy intervention(s) across two workplaces to determine impacts on caregiver-employee health. A quasi-experimental pre-post design will allow the caregiver-friendly workplace policy intervention(s) to be tested with respect to potential impacts on health, and specifically on caregiver employee mental, psychosocial, and physical health. Framed within a comparative case study design, Study B will utilize cost-benefit and cost-effectiveness analysis approaches to evaluate the economic impacts of the caregiver-friendly workplace policy intervention(s) for each of the two participating workplaces. Framed within a comparative case study design, Study C will undertake an implementation analysis of the caregiver-friendly workplace policy intervention(s) in each participating workplace in order to determine: the degree of support for the intervention(s) (reflected in the workplace culture); how sex and gender are implicated; co-workers' responses to the chosen intervention(s), and

  5. Experimental characterization of the unsteady natural wake of the full-scale square back Ahmed body: flow bi-stability and spectral analysis

    Science.gov (United States)

    Volpe, Raffaele; Devinant, Philippe; Kourta, Azeddine

    2015-05-01

    In recent years, the increasing interest in reducing the aerodynamic drag of vehicles, such as station wagons, minivans or buses, has led research to focus on the characterization of square back bluff geometries. In this paper, the results of an extensive experimental campaign on the full-scale well-known body of Ahmed et al. (1984) are presented, for two height-based Reynolds numbers, and . Eighty-one measurement points were used to map the base pressure field, while the wake topology was investigated by means of a series of ten 2D Particle Image Velocimetry planes. These measurements clearly show that the wake presents a bi-stable behavior, characterized by a random succession of switches between two well-defined mutually symmetric configurations, confirming the results from Grandemange et al. (J Fluid Mech 722:51-84, 2013b. doi: 10.1017/jfm.2013.83) for the same model. For the presented results, the timescale of this phenomenon is of the order of . The sensitivity of the bi-stability to the yaw angle was also investigated, and considerations on how to take such a behavior into account in post-processing this kind of field are given. High-frequency measurements were also carried out with four piezoelectric transducers and a synchronized two-component hot-wire. The results show a low-frequency spectral activity: peaks at and 0.19, corresponding to vortex shedding modes, were found on the lateral base pressures and in the far wake, whereas a signature at was visible on the vertical base centerline and in the recirculation bubble shear layer. Correlation analysis and proper orthogonal decomposition confirm the interpretation of the latter mode as the pumping of the recirculation bubble.

  6. hSmad5 gene, a human hSmad family member: its full length cDNA, genomic structure, promoter region and mutation analysis in human tumors.

    Science.gov (United States)

    Gemma, A; Hagiwara, K; Vincent, F; Ke, Y; Hancock, A R; Nagashima, M; Bennett, W P; Harris, C C

    1998-02-19

    hSmad (mothers against decapentaplegic)-related proteins are important messengers within the Transforming Growth Factor-beta1 (TGF-beta1) superfamily signal transduction pathways. To further characterize a member of this family, we obtained a full length cDNA of the human hSmad5 (hSmad5) gene by rapid amplification of cDNA ends (RACE) and then determined the genomic structure of the gene. There are eight exons and two alternative transcripts; the shorter transcript lacks exon 2. We identified the hSmad5 promoter region from a human genomic YAC clone by obtaining the nucleotide sequence extending 1235 base pairs upstream of the 5' end of the cDNA. We found a CpG island consistent with a promoter region, and we demonstrated promoter activity in a 1232 bp fragment located upstream of the transcription initiation site. To investigate the frequency of somatic hSmad5 mutations in human cancers, we designed intron-based primers to examine coding regions by polymerase chain reaction-single strand conformation polymorphism (PCR-SSCP) analysis. Neither homozygous deletions or point mutations were found in 40 primary gastric tumors and 51 cell lines derived from diverse types of human cancer including 20 cell lines resistant to the growth inhibitory effects of TGF-beta1. These results suggest that the hSmad5 gene is not commonly mutated and that other genetic alterations mediate the loss of TGF-beta1 responsiveness in human cancers.

  7. An Attenuated LC16m8 Smallpox Vaccine: Analysis of Full-Genome Sequence and Induction of Immune Protection§

    Science.gov (United States)

    Morikawa, Shigeru; Sakiyama, Tokuki; Hasegawa, Hideki; Saijo, Masayuki; Maeda, Akihiko; Kurane, Ichiro; Maeno, Go; Kimura, Junko; Hirama, Chie; Yoshida, Teruhiko; Asahi-Ozaki, Yasuko; Sata, Tetsutaro; Kurata, Takeshi; Kojima, Asato

    2005-01-01

    The potential threat of smallpox bioterrorism has made urgent the development of lower-virulence vaccinia virus vaccines. An attenuated LC16m8 (m8) vaccine was developed in 1975 from the Lister strain used in the World Health Organization smallpox eradication program but was not used against endemic smallpox. Today, no vaccines can be tested with variola virus for efficacy in humans, and the mechanisms of immune protection against the major intracellular mature virion (IMV) and minor extracellular enveloped virion (EEV) populations of poxviruses are poorly understood. Here, we determined the full-genome sequences of the m8, parental LC16mO (mO), and grandparental Lister (LO) strains and analyzed their evolutionary relationships. Sequence data and PCR analysis indicated that m8 was a progeny of LO and that m8 preserved almost all of the open reading frames of vaccinia virus except for the disrupted EEV envelope gene B5R. In accordance with this genomic background, m8 induced 100% protection against a highly pathogenic vaccinia WR virus in mice by a single vaccination, despite the lack of anti-B5R and anti-EEV antibodies. The immunogenicity and priming efficacy with the m8 vaccine consisting mainly of IMV were as high as those with the intact-EEV parental mO and grandparental LO vaccines. Thus, mice vaccinated with 107 PFU of m8 produced low levels of anti-B5R antibodies after WR challenge, probably because of quick clearance of B5R-expressing WR EEV by strong immunity induced by the vaccination. These results suggest that priming with m8 IMV provides efficient protection despite undetectable levels of immunity against EEV. PMID:16140764

  8. Engineering design and prototype development of a full scale ultrasound system for virgin olive oil by means of numerical and experimental analysis.

    Science.gov (United States)

    Clodoveo, Maria Lisa; Moramarco, Vito; Paduano, Antonello; Sacchi, Raffaele; Di Palmo, Tiziana; Crupi, Pasquale; Corbo, Filomena; Pesce, Vito; Distaso, Elia; Tamburrano, Paolo; Amirante, Riccardo

    2017-07-01

    The aim of the virgin olive oil extraction process is mainly to obtain the best quality oil from fruits, by only applying mechanical actions while guaranteeing the highest overall efficiency. Currently, the mechanical methods used to extract virgin oils from olives are basically of two types: the discontinuous system (obsolete) and the continuous one. Anyway the system defined as "continuous" is composed of several steps which are not all completely continuous, due to the presence of the malaxer, a device that works in batch. The aim of the paper was to design, realize and test the first full scale sono-exchanger for the virgin olive oil industry, to be placed immediately after the crusher and before the malaxer. The innovative device is mainly composed of a triple concentric pipe heat exchanger combined with three ultrasound probes. This mechanical solution allows both the cell walls (which release the oil droplets) along with the minor compounds to be destroyed more effectively and the heat exchange between the olive paste and the process water to be accelerated. This strategy represents the first step towards the transformation of the malaxing step from a batch operation into a real continuous process, thus improving the working capacity of the industrial plants. Considering the heterogeneity of the olive paste, which is composed of different tissues, the design of the sono-exchanger required a thorough fluid dynamic analysis. The thermal effects of the sono-exchanger were monitored by measuring the temperature of the product at the inlet and the outlet of the device; in addition, the measurement of the pigments concentration in the product allowed monitoring the mechanical effects of the sono-exchanger. The effects of the innovative process were also evaluated in terms of extra virgin olive oil yields and quality, evaluating the main legal parameters, the polyphenol and tocopherol content. Moreover, the activity of the polyphenol oxidase enzyme in the olive

  9. Cloning and sequence analysis of a full-length cDNA of SmPP1cb encoding turbot protein phosphatase 1 beta catalytic subunit

    Science.gov (United States)

    Qi, Fei; Guo, Huarong; Wang, Jian

    2008-02-01

    Reversible protein phosphorylation, catalyzed by protein kinases and phosphatases, is an important and versatile mechanism by which eukaryotic cells regulate almost all the signaling processes. Protein phosphatase 1 (PP1) is the first and well-characterized member of the protein serine/threonine phosphatase family. In the present study, a full-length cDNA encoding the beta isoform of the catalytic subunit of protein phosphatase 1(PP1cb), was for the first time isolated and sequenced from the skin tissue of flatfish turbot Scophthalmus maximus, designated SmPP1cb, by the rapid amplification of cDNA ends (RACE) technique. The cDNA sequence of SmPP1cb we obtained contains a 984 bp open reading frame (ORF), flanked by a complete 39 bp 5' untranslated region and 462 bp 3' untranslated region. The ORF encodes a putative 327 amino acid protein, and the N-terminal section of this protein is highly acidic, Met-Ala-Glu-Gly-Glu-Leu-Asp-Val-Asp, a common feature for PP1 catalytic subunit but absent in protein phosphatase 2B (PP2B). And its calculated molecular mass is 37 193 Da and pI 5.8. Sequence analysis indicated that, SmPP1cb is extremely conserved in both amino acid and nucleotide acid levels compared with the PP1cb of other vertebrates and invertebrates, and its Kozak motif contained in the 5'UTR around ATG start codon is GXXAXXGXX ATGG, which is different from mammalian in two positions A-6 and G-3, indicating the possibility of different initiation of translation in turbot, and also the 3'UTR of SmPP1cb is highly diverse in the sequence similarity and length compared with other animals, especially zebrafish. The cloning and sequencing of SmPP1cb gene lays a good foundation for the future work on the biological functions of PP1 in the flatfish turbot.

  10. Comparison of clinical outcomes in PRK with a standard and aspherical optimized profile: a full case analysis of 100 eyes with 1-year follow-up

    Directory of Open Access Journals (Sweden)

    Dausch D

    2014-11-01

    Full Text Available Dieter Dausch,1,2 Burglinde Dausch,2 Matthias Wottke,3 Georg Sluyterman van Langeweyde31Chung-Ang University, Seoul, South Korea; 2Augen-Laser-Klinik Nürnberg, Nuremberg, Germany; 3Carl Zeiss Meditec AG, Jena, Germany Purpose: One hundred eyes from 55 adult patients with myopia were retrospectively studied to determine the comparative safety, efficacy, and predictability of aberration smart ablation (ASA and a new advanced ablation algorithm (Triple-A using the MEL® 80 excimer laser.Methods: Fifty myopic eyes with a manifest refraction spherical equivalent (MRSE between -1.0 diopters (D and -9.75 D were consecutively treated with photorefractive keratectomy ASA, and 50 myopic eyes with an MRSE between -1.38 D and -11.0 D with photorefractive keratectomy Triple-A. Uncorrected distance visual acuity, MRSE, the absolute value of the cylinder, corrected distance visual acuity, and postoperative complications at 1 month, 3 months, 6 months, and 12 months (1 year were descriptively analyzed and compared at 1 year.Results: After 12 months, the MRSE variance was statistically significantly better in patients triaged to receive Triple-A compared with patients receiving ASA (ASA, ±0.7 D; Triple-A, ±0.15 D; P<0.001. Furthermore, no patient in the Triple-A group had any cylinder postoperatively. Patients in the Triple-A treatment arm achieved a superior result. No statistically significant difference in the two treatment arms was noted for the analysis of the mean MRSE at 12 months (P=0.78.Conclusion: Triple-A was more effective than standard aspherical surgical intervention in a number of treatment outcome parameters (eg, MRSE, astigmatism, efficacy index. The two surgical procedures were equivalent in terms of safety. Keywords: aberration smart ablation (ASA, manifest refraction spherical equivalent, Triple-A advanced ablation algorithm, uncorrected distance visual acuity, corrected distance visual acuity, excimer laser, PRK, ablation profile

  11. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>Centre for Agriculture and Bioscience International( CABI) is a not-for-profit international Agricultural Information Institute with headquarters in Britain. It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment. CABI Full-text is one of the publishing products of CABI.CABI’s full text repository is growing rapidly and has now been integrated into all our databases including CAB Abstracts,Global Health,our Internet Resources and Abstract Journals. There are currently over 60,000 full text articles available to access. These documents,made possible by agreement with third

  12. 满月儿童661例体格发育情况分析%Analysis of physical development of 661 full moon children

    Institute of Scientific and Technical Information of China (English)

    马卫平

    2013-01-01

    目的 了解满月儿童体格发育情况及其影响因素,为指导科学喂养提供依据.方法 选用2011年10月-2012年10月在南宁市江南区福建园社区卫生服务中心进行满月体格检查的661例儿童作为调查对象,进行体格发育指标测量并分析.结果 与出生时相比,体质量增加平均值男为1 207.05 g,女为1 043.94 g;身长增加平均值男为4.30 cm,女为3.61cm.该组儿童喂养方式中母乳喂养占90.92%,人工喂养率占6.20%,混合喂养率占2.88%.不同喂养方式的儿童身高和体质量的增长无差异(P>0.05).低出生体质量儿和正常出生体质量儿身高和体质量的增加无差异(P>0.05).早产儿与足月儿体质量增加无差异(P>0.05),身高增加有差异(P<0.01).低出生体质量早产儿与正常出生体质量足月儿相比较,体质量增加无差异(P>0.05),身高增加有差异(P<0.05).结论 该组儿童平均增加体质量和身高都达到了参考标准,生长发育状况较好.应进一步提高儿童保健服务质量,完善和规范满月儿童体检,指导家长科学喂养,并使全社会都来重视儿童健康.%To understand the physical development and its influencing factors of full moon children,and provide evidence for scientific feeding.[Methods] A total of 661 full moon children received physical examination in Fujian Park Community Health Service Center of Jiangnan District from October 2011 to October 2012 were selected as study objects for physical development index measurement and analysis.[Results] Compared with birth,body mass growth of average value was 1 207.05 g of male and 1 043.94 g of female ; height growth of average value was 4.30 cm of male,3.61 cm of female.In this group of children,feeding patterns of breastfeeding accounted for 90.92%,artificial feeding accounted for 6.20%,mixed feeding accounted for 2.88%.Different ways of feeding children's height and weight growth was not different,(P > 0.05).Low

  13. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>Centre for Agriculture and Bioscience International(CABI)is a not-for-profit international Agricultural Information Institute with headquarters in Britain.It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment.CABI Full-text is one of the publishing products of CABI.CABI’s full text repository is growing rapidly

  14. Chagas disease: current epidemiological trends after the interruption of vectorial and transfusional transmission in the Southern Cone countries

    Directory of Open Access Journals (Sweden)

    Alvaro Moncayo

    2003-07-01

    Full Text Available Chagas disease, named after Carlos Chagas who first described it in 1909, exists only on the American Continent. It is caused by a parasite, Trypanosoma cruzi, transmitted to humans by blood-sucking triatomine bugs and by blood transfusion. Chagas disease has two successive phases, acute and chronic. The acute phase lasts 6 to 8 weeks. After several years of starting the chronic phase, 20% to 35% of the infected individuals, depending on the geographical area will develop irreversible lesions of the autonomous nervous system in the heart, esophagus, colon and the peripheral nervous system. Data on the prevalence and distribution of Chagas disease improved in quality during the 1980's as a result of the demographically representative cross-sectional studies carried out in countries where accurate information was not available. A group of experts met in Brasília in 1979 and devised standard protocols to carry out countrywide prevalence studies on human T. cruzi infection and triatomine house infestation. Thanks to a coordinated multi-country program in the Southern Cone countries the transmission of Chagas disease by vectors and by blood transfusion has been interrupted in Uruguay in1997, in Chile in 1999, and in 8 of the 12 endemic states of Brazil in 2000 and so the incidence of new infections by T. cruzi in the whole continent has decreased by 70%. Similar control multi-country initiatives have been launched in the Andean countries and in Central America and rapid progress has been recorded to ensure the interruption of the transmission of Chagas disease by 2005 as requested by a Resolution of the World Health Assembly approved in 1998. The cost-benefit analysis of the investments of the vector control program in Brazil indicate that there are savings of US$17 in medical care and disabilities for each dollar spent on prevention, showing that the program is a health investment with good return. Since the inception in 1979 of the Steering

  15. Full-scale demonstration of in situ cometabolic biodegradation of trichloroethylene in groundwater 2. Comprehensive analysis of field data using reactive transport modeling

    Science.gov (United States)

    Gandhi, Rahul K.; Hopkins, Gary D.; Goltz, Mark N.; Gorelick, Steven M.; McCarty, Perry L.

    2002-04-01

    We present an analysis of an extensively monitored full-scale field demonstration of in situ treatment of trichloroethylene (TCE) contamination by aerobic cometabolic biodegradation. The demonstration was conducted at Edwards Air Force Base in southern California. There are two TCE-contaminated aquifers at the site, separated from one another by a clay aquitard. The treatment system consisted of two recirculating wells located 10 m apart. Each well was screened in both of the contaminated aquifers. Toluene, oxygen, and hydrogen peroxide were added to the water in both wells. At one well, water was pumped from the upper aquifer to the lower aquifer. In the other well, pumping was from the lower to the upper aquifer. This resulted in a ``conveyor belt'' flow system with recirculation between the two aquifers. The treatment system was successfully operated for a 410 day period. We explore how well a finite element reactive transport model can describe the key processes in an engineered field system. Our model simulates TCE, toluene, oxygen, hydrogen peroxide, and microbial growth/death. Simulated processes include advective-dispersive transport, biodegradation, the inhibitory effect of hydrogen peroxide on biomass growth, and oxygen degassing. Several parameter values were fixed to laboratory values or values from previous modeling studies. The remaining six parameter values were obtained by calibrating the model to 7213 TCE concentration data and 6997 dissolved oxygen concentration data collected during the demonstration using a simulation-regression procedure. In this complex flow field involving reactive transport, TCE and dissolved oxygen concentration histories are matched very well by the calibrated model. Both simulated and observed toluene concentrations display similar high-frequency oscillations due to pulsed toluene injection approximately one half hour during each 8 hour period. Simulation results indicate that over the course of the demonstration, 6.9 kg

  16. Late vs early clamping of the umbilical cord in full-term neonates: systematic review and meta-analysis of controlled trials.

    Science.gov (United States)

    Hutton, Eileen K; Hassan, Eman S

    2007-03-21

    With few exceptions, the umbilical cord of every newborn is clamped and cut at birth, yet the optimal timing for this intervention remains controversial. To compare the potential benefits and harms of late vs early cord clamping in term infants. Search of 6 electronic databases (on November 15, 2006, starting from the beginning of each): the Cochrane Pregnancy and Childbirth Group trials register, the Cochrane Neonatal Group trials register, the Cochrane library, MEDLINE, EMBASE, and CINHAL; hand search of secondary references in relevant studies; and contact of investigators about relevant published research. Controlled trials comparing late vs early cord clamping following birth in infants born at 37 or more weeks' gestation. Two reviewers independently assessed eligibility and quality of trials and extracted data for outcomes of interest: infant hematologic status; iron status; and risk of adverse events such as jaundice, polycythemia, and respiratory distress. The meta-analysis included 15 controlled trials (1912 newborns). Late cord clamping was delayed for at least 2 minutes (n = 1001 newborns), while early clamping in most trials (n = 911 newborns) was performed immediately after birth. Benefits over ages 2 to 6 months associated with late cord clamping include improved hematologic status measured as hematocrit (weighted mean difference [WMD], 3.70%; 95% confidence interval [CI], 2.00%-5.40%); iron status as measured by ferritin concentration (WMD, 17.89; 95% CI, 16.58-19.21) and stored iron (WMD, 19.90; 95% CI, 7.67-32.13); and a clinically important reduction in the risk of anemia (relative risk (RR), 0.53; 95% CI, 0.40-0.70). Neonates with late clamping were at increased risk of experiencing asymptomatic polycythemia (7 studies [403 neonates]: RR, 3.82; 95% CI, 1.11-13.21; 2 high-quality studies only [281 infants]: RR, 3.91; 95% CI, 1.00-15.36). Delaying clamping of the umbilical cord in full-term neonates for a minimum of 2 minutes following birth is

  17. Cloning and sequence analysis of a full-length cDNA of SmPP1cb encoding turbot protein phosphatase 1 beta catalytic subunit

    Institute of Scientific and Technical Information of China (English)

    QI Fei; GUO Huarong; WANG Jian

    2008-01-01

    Reversible protein phosphorylation,catalyzed by protein kinases and phosphatases,is an important and versatile mechanism by which eukaryotic cells regulate almost all the signaling processes.Protein phosphatase 1(PP1) is the first and well-characterized member of the protein serine/threoninephosphatase family.In the present study.a full-length cDNA encoding the beta isolorm of the catalytic subunit of protein phosphatase 1(PP1cb).was for the first time isolated and sequenced from the skin tissue of flatfish turbot Scophthalmus maximus,designated SmPP1cb,by the rapid amplification of cDNA ends (RACE) technique.The cDNA sequence of SmPP1cb we obtained contains a 984 bp open reading frame(ORF),flanked by a complete 39 bp 5' untranslated region and 462 bp 3' untranslated region.The ORF encodes a putative 327 amino acid protein.and the N-terminal section of this protein iS highly acidic,Met-Ala-Glu-Gly-Glu-Leu-Asp-Val-Asp.a common feature for PP1 catalytic subunit but absent in protein phosphatase 2B(PP2B).And its calculated molecular mass is 37 193 Da and pI 5.8.Sequence analysis indicated that,SmPP1cb is extremely conserved in both amino acid and nucleotide acid levels compared with the PP1cb of other vertebrates and invertebrates.and its Kozak motif contained in the 5'UTR around ATG start codon is GXXAXXGXXATGG,which is different from mammalian in two positions A-6 and G-3,indicating the possibility of different initiation of translation in turbot,and also the 3'UTR of SmPP1cb is highly diverse in the sequence similarity and length compared with other animals.especially zebrafish.The cloning and sequencing of SmPP1cb gene lays a good foundation for the future work on the biological functions of PP1 in the flatfish turbot.

  18. full on riot

    Directory of Open Access Journals (Sweden)

    Moses Iten

    2005-08-01

    Full Text Available “hey moses full on riot in lawson st the station’s on fire! been going since 4. molotov and more. full on,” reads an SMS message received on the backseat of a Tasmanian bus. What follows is a journey through the landscape of a Gunavidji, whose brothers have all gone to the land of the dead; metallic scraping in the glass cases of the Hobart Museum; a Palestinian woman giving up on her people; land-snails exposing cultural inaccuracies; photographing Australia’s war zone; entering the St Peter’s Basilica of Rome with bulldozers - all in the name of preparing to interview prominent Israeli writer Etgar Keret.

  19. Full moon and crime.

    Science.gov (United States)

    Thakur, C P; Sharma, D

    The incidence of crimes reported to three police stations in different towns (one rural, one urban, one industrial) was studied to see if it varied with the day of the lunar cycle. The period of the study covered 1978-82. The incidence of crimes committed on full moon days was much higher than on all other days, new moon days, and seventh days after the full moon and new moon. A small peak in the incidence of crimes was observed on new moon days, but this was not significant when compared with crimes committed on other days. The incidence of crimes on equinox and solstice days did not differ significantly from those on other days, suggesting that the sun probably does not influence the incidence of crime. The increased incidence of crimes on full moon days may be due to "human tidal waves" caused by the gravitational pull of the moon.

  20. Full tree harvesting update

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, K.; White, K.

    1981-03-01

    An important harvesting alternative in North America is the Full Tree Method, in which trees are felled and transported to roadside, intermediate or primary landings with limbs and branches intact. The acceptance of Full Tree Systems is due to many factors including: labour productivity and increased demands on the forest for ''new products''. These conditions are shaping the future look for forest Harvesting Systems, but must not be the sole determinants. All harvesting implications, such as those affecting Productivity and silviculture, should be thoroughly understood. This paper does not try to discuss every implication, nor any particular one in depth; its purpose is to highlight those areas requiring consideration and to review several current North American Full Tree Systems. (Refs. 5).

  1. Design and Performance Analysis of 1-Bit FinFET Full Adder Cells for Subthreshold Region at 16 nm Process Technology

    Directory of Open Access Journals (Sweden)

    ‘Aqilah binti Abdul Tahrim

    2015-01-01

    Full Text Available The scaling process of the conventional 2D-planar metal-oxide semiconductor field-effect transistor (MOSFET is now approaching its limit as technology has reached below 20 nm process technology. A new nonplanar device architecture called FinFET was invented to overcome the problem by allowing transistors to be scaled down into sub-20 nm region. In this work, the FinFET structure is implemented in 1-bit full adder transistors to investigate its performance and energy efficiency in the subthreshold region for cell designs of Complementary MOS (CMOS, Complementary Pass-Transistor Logic (CPL, Transmission Gate (TG, and Hybrid CMOS (HCMOS. The performance of 1-bit FinFET-based full adder in 16-nm technology is benchmarked against conventional MOSFET-based full adder. The Predictive Technology Model (PTM and Berkeley Shortchannel IGFET Model-Common Multi-Gate (BSIM-CMG 16 nm low power libraries are used. Propagation delay, average power dissipation, power-delay-product (PDP, and energy-delay-product (EDP are analysed based on all four types of full adder cell designs of both FETs. The 1-bit FinFET-based full adder shows a great reduction in all four metric performances. A reduction in propagation delay, PDP, and EDP is evident in the 1-bit FinFET-based full adder of CPL, giving the best overall performance due to its high-speed performance and good current driving capabilities.

  2. Comparative Performance Analysis of XOR-XNOR Function Based High-Speed CMOS Full Adder Circuits For Low Voltage VLSI Design

    Directory of Open Access Journals (Sweden)

    Sudarshan Tiwari

    2012-05-01

    Full Text Available This paper presents comparative study of high-speed, low-power and low voltage full adder circuits. Our approach is based on XOR-XNOR design full adder circuits in a single unit. A low power and high performance 9T full adder cell using a design style called “XOR (3T” is discussed. The designed circuit commands a high degree of regularity and symmetric higher density than the conventional CMOS design style as well as it lowers power consumption by using XOR (3T logic circuits. Gate Diffusion Input (GDI technique of low-power digital combinatorial circuit design is also described. This technique helps inreducing the power consumption and the area of digital circuits while maintaining low complexity of logic design. This paper analyses, evaluates and compares the performance of various adder circuits. Severalsimulations conducted using different voltage supplies, load capacitors and temperature variation demonstrate the superiority of the XOR (3T based full adder designs in term of delay, power and powerdelay product (PDP compared to the other full adder circuits. Simulation results illustrate the superiority of the designed adder circuits against the conventional CMOS, TG and Hybrid full adder circuits in terms of power, delay and power delay product (PDP.

  3. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Centre for Agriculture and Bioscience International(CABI)is a not-for-profit international Agricultural Information Institute with headquarters in Britain.It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment.CABI Full-text is one of the publishing products of CABI.CABI’s full text repository is growing rapidly and has now been integrated into all our databases including CAB Abstracts,Global Health

  4. Compressive full waveform lidar

    Science.gov (United States)

    Yang, Weiyi; Ke, Jun

    2017-05-01

    To avoid high bandwidth detector, fast speed A/D converter, and large size memory disk, a compressive full waveform LIDAR system, which uses a temporally modulated laser instead of a pulsed laser, is studied in this paper. Full waveform data from NEON (National Ecological Observatory Network) are used. Random binary patterns are used to modulate the source. To achieve 0.15 m ranging resolution, a 100 MSPS A/D converter is assumed to make measurements. SPIRAL algorithm with canonical basis is employed when Poisson noise is considered in the low illuminated condition.

  5. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Centre for Agriculture and Bioscience International(CABI)is a not-for-profit international Agricultural Information Institute with headquarters in Britain.It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment.CABI Full-text is one of the publishing products of CABI.CABI’s full text repository is growing rapidly and has now been integrated into all our databases including CAB Abstracts,Global Health,our Internet Resources and Jour-

  6. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Centre for Agriculture and Bioscience International( CABI) is a not-for-profit international Agricultural Information Institute with headquarters in Britain. It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment. CABI Full-text is one of the publishing products of CABI.

  7. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Centre for Agriculture and Bioscience International(CABI) is a not-for-profit international Agricultural Information Institute with headquarters in Britain. It aims to improve people’s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment. CABI Full-text is one of the publishing products of CABI.

  8. About CABI Full Text

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>Centre for Agriculture and Bioscience International(CABI)is a not-for-profit international Agricultural Information Institute with headquarters in Britain. It aims to improve people s lives by providing information and applying scientific expertise to solve problems in agriculture and the environment. CABI Full-text is one of the publishing products of CABI.

  9. Emptiness and Fullness

    DEFF Research Database (Denmark)

    Bregnbæk, Susanne; Bunkenborg, Mikkel

    As critical voices question the quality, authenticity, and value of people, goods, and words in post-Mao China, accusations of emptiness render things open to new investments of meaning, substance, and value. Exploring the production of lack and desire through fine-grained ethnography, this volume......, there is a pervasive concern with states of lack and emptiness and the contributions suggest that this play of emptiness and fullness is crucial to ongoing constructions of quality, value, and subjectivity in China....

  10. Curative effect analysis of front teeth full crown restoration%前牙全冠修复的疗效分析

    Institute of Scientific and Technical Information of China (English)

    贺燕; 李扬

    2014-01-01

    ObjectiveAnalysis of different metal porcelain crowns and casting porcelain crown in the repair of anterior tooth clinical results.MethodsSelect our hospital from January 2013 to January 2014 line need full crown restoration to 400 teeth of 140 patients, combining the actual requirement of patients respectively production casting four metal porcelain crowns (respectively, gold-plated nickel chromium alloy cobalt chromium alloy, palladium silver alloy, nickel chromium alloy and gold platinum alloy) and casting porcelain crown all the 80 cases, all patients were given clinical follow-up of 2 years. Evaluate each full crown restoration color, edge, surface integrity, gums healthy gums and dyeing conditions.ResultsCasting porcelain crown color effect is signifi cantly better than the metal porcelain crowns, which compare the difference was statistically signifi cant (P<0.05); In terms of marginal fi t, gold platinum alloy was signifi cantly better than several other metal porcelain crowns, compare the difference was statistically signifi cant (P<0.05); On edge coloring, color and gum health, casting porcelain crown, cobalt chromium alloy PFM crown, precious metal alloy PFM crown was signifi cantly better than nickel-chromium alloy PFM crowns, compare the difference was statistically signifi cant (P<0.05).ConclusionIn terms of marginal fi t, gold platinum alloy porcelain crowns the best clinical effect; In terms of aesthetic effect, casting porcelain crown clinical effect is best; In terms of edge coloring and periodontal health, precious metal alloy porcelain teeth and the clinical effect of casting porcelain crown is better.%目的:分析不同金属烤瓷冠和铸瓷冠在前牙修复中的效果。方法选择我院2013年1月~2015年1月收治的需要行全冠修复的140例患者上前牙400颗,结合患者的实际需要分别铸造4种金属烤瓷冠(即为镀金镍铬合金钴铬合金、钯银合金、镍铬合金和金铂合金)和铸瓷冠各80

  11. Simulation and analysis of an isolated full-bridge DC/DC boost converter operating with a modified perturb and observe maximum power point tracking algorithm

    Directory of Open Access Journals (Sweden)

    Calebe A. Matias

    2017-07-01

    Full Text Available The purpose of the present study is to simulate and analyze an isolated full-bridge DC/DC boost converter, for photovoltaic panels, running a modified perturb and observe maximum power point tracking method. The zero voltage switching technique was used in order to minimize the losses of the converter for a wide range of solar operation. The efficiency of the power transfer is higher than 90% for large solar operating points. The panel enhancement due to the maximum power point tracking algorithm is 5.06%.

  12. FATIGUE DAMAGE MECHANISM AND ITS APPLICATION BASED ON FULL-SCALE ANALYSIS OF STEEL-CONCRETE COMPOSITE SLAB SUBJECTED TO REPETITION OF TRAFFIC

    OpenAIRE

    OGIYAMA, Yotaro; FUJIYAMA, Chikako; TAKASUKA, Takehiro

    2014-01-01

    The purpose of this study is to analyze the fatigue damage process of a plate girder bridgesupporting a steel-concrete composite slab, and to propose a method for maintenance of the composite slab.To analyze a full-scale bridge subjected to heavy traffic, three-dimensional non-linear FE analyses andloading rates based on an actual bridge are used.The full-scale bridge model is a 2-lane road bridge with 30 m span length and 10.55 m width, consistingof main girders with vertical stiffeners, cro...

  13. Plate Full of Color

    Centers for Disease Control (CDC) Podcasts

    2008-08-04

    The Eagle Books are a series of four books that are brought to life by wise animal characters - Mr. Eagle, Miss Rabbit, and Coyote - who engage Rain That Dances and his young friends in the joy of physical activity, eating healthy foods, and learning from their elders about health and diabetes prevention. Plate Full of Color teaches the value of eating a variety of colorful and healthy foods.  Created: 8/4/2008 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 8/5/2008.

  14. Multi-Criteria Decision Analysis of Test Endpoints for Detecting the Effects of Endocrine Active Substances in Fish Full Life Cycle Tests

    Science.gov (United States)

    Fish full life cycle (FFLC) tests are increasingly required in the ecotoxicological assessment of endocrine active substances. However, FFLC tests have not been internationally standardized or validated, and it is currently unclear how such tests should best be designed to provid...

  15. Dimensionality Assessment Using the Full-Information Item Bifactor Analysis for Graded Response Data: An Illustration with the State Metacognitive Inventory

    Science.gov (United States)

    Immekus, Jason C.; Imbrie, P. K.

    2008-01-01

    Dimensionality assessment using the full-information item bifactor model for graded response data is provided. The model applies to data in which each item relates to a general factor and one group factor. Specifically, alternative model specification within item response theory (IRT) is shown to test a scale's factor structure. For illustrative…

  16. JSTOR Full Text Database for Back Issues of Academic Journals and Its Feature Analysis%过刊全文数据库JSTOR及其特色分析

    Institute of Scientific and Technical Information of China (English)

    郭依群

    2003-01-01

    JSTOR is a full text database for back issues of academic journals, especially those related to humane studies, social science and natural science. This article describes the original intention of JSTOR, analyzes the features of its collections, user interface and use value, and discusses how it is introduced to users.

  17. Full-scale testing, production and cost analysis data for the advanced composite stabilizer for Boeing 737 aircraft. Volume 1: Technical summary

    Science.gov (United States)

    Aniversario, R. B.; Harvey, S. T.; Mccarty, J. E.; Parsons, J. T.; Peterson, D. C.; Pritchett, L. D.; Wilson, D. R.; Wogulis, E. R.

    1983-01-01

    The full scale ground test, ground vibration test, and flight tests conducted to demonstrate a composite structure stabilizer for the Boeing 737 aircraft and obtain FAA certification are described. Detail tools, assembly tools, and overall production are discussed. Cost analyses aspects covered include production costs, composite material usage factors, and cost comparisons.

  18. Confocal Raman microspectrometry: a vectorial electromagnetic treatment of the light focused and collected through a planar interface and its application to the study of a thin coating.

    Science.gov (United States)

    Sourisseau, C; Maraval, P

    2003-11-01

    In-depth confocal Raman microspectrometry (CRM) studies through a planar interface between materials of mismatched refraction indices are known to be affected by a decrease of both the collected Raman intensity and the axial resolution as a function of the penetration depth. Following a previous model, which takes the refraction, diffraction, and spherical aberration effects into account when focusing a Gaussian incident laser beam with a high numerical aperture objective lens, a complete vectorial treatment of these phenomena is considered. It is demonstrated that off-axis refraction effects cannot be neglected and that the dimension of the confocal pinhole aperture plays a crucial role on the effective focal plane position and on the collection efficiency. We thus propose a more rigorous and complete approach to the problem, and we find a very good agreement between experimental and theoretical Raman intensity variations for a thick polyethylene sample as a function of the penetration depth. As compared with calculations where only refraction was considered, we confirm that the lengthening of the focus even for a large penetration depth is significantly reduced upon diffraction effects. As an illustrative example, the theoretical Raman responses for a thin coating of approximately 20 microns on a polymer substrate were investigated and compared to experimental results already published. Even though the interfacial region is spread over approximately 5-6 microns when using a 100x objective and a confocal pinhole of 200 microns diameter, it is definitively concluded that the apparent axial resolution is not drastically deteriorated with increasing depth and that the coating thickness may be directly estimated with a precision of approximately 1.0 micron (5%).

  19. A Method for Measuring Orientation within a Magnetic Resonance Imaging Scanner using Gravity and the Static Magnetic Field (VectOrient).

    Science.gov (United States)

    van Niekerk, Adam; van der Kouwe, Andre; Meintjes, Ernesta

    2017-01-25

    In MRI brain imaging, subject motion limits obtainable image clarity. Due to the hardware layout of an MRI scanner, gradient excitations can be used to rapidly detect position. Orientation, however, is more difficult to detect and is commonly calculated by comparing the position measurements of multiple spatially constrained points to a reference dataset. The result is increased size of the apparatus the subject must wear, which can influence the imaging workflow. In optical based methods marker attachment sites are limited due to the line of sight requirement between the camera and marker, and an external reference frame is introduced. To address these challenges a method called VectOrient is proposed for orientation measurement that is based on vector observations of gravity and the MRI scanner's static magnetic field. A prototype device comprising of an accelerometer, magnetometer and angular rate sensor shows good MRI compatibility. Phantom scans of a pineapple with zero scanner specific calibration achieve comparable results to a rigid body registration algorithm with deviations less than 0.8 degrees over 28 degree changes in orientation. Dynamic performance shows potential for prospective motion correction as rapid changes in orientation (peak 20 degrees per second) can be corrected. The pulse sequence implemented achieves orientation updates with a latency estimated to be less than 12.7 ms, of which only a small fraction (<1 ms) is used for computing orientation from the raw sensor signals. The device is capable of quantifying subject respiration and heart rates. The proposed approach for orientation estimation could help address some limitations of existing methods such as orientation measurement range, temporal resolution, ease of use and marker placement.

  20. Very Efficient Spin Polarization Analysis (VESPA): New Exchange Scattering-based Setup for Spin-resolved ARPES at APE-NFFA Beamline at Elettra

    CERN Document Server

    Bigi, Chiara; Vobornik, Ivana; Das, Pranab K; Benedetti, Davide; Salvador, Federico; Panaccione, Giancarlo; Rossi, Giorgio

    2016-01-01

    Complete Photoemission Experiments, enabling to measure the full quantum set of the photoelectron final state, are in high demand for the study of materials and nanostructures whose properties are determined by strong electron and spin correlations. We report here on the implementation of the new spin polarimeter VESPA (Very Efficient Spin Polarization Analysis) at the APE-NFFA Beamline at Elettra that is based on the exchange coupling between the photoelectron spin and a ferromagnetic surface in a reflectometry setup. The system was designed to be integrated with a dedicated Scienta-Omicron DA30 electron energy analyser allowing for two simultaneous reflectometry measurements, along perpendicular axes, that, after magnetization switching of the two targets allow to perform the 3D vectorial reconstruction of the spin polarization while operating the DA30 in high resolution mode. VESPA represents the very first installation for spin-resolved ARPES (SP-ARPES) at the Elettra synchrotron in Trieste, and is being ...