WorldWideScience

Sample records for frontal collision join

  1. Modeling and simulation of cars in frontal collision

    Science.gov (United States)

    Deac, S. C.; Perescu, A.; Simoiu, D.; Nyaguly, E.; Crâştiu, I.; Bereteu, L.

    2018-01-01

    Protection of cars, mainly drivers and passengers in a collision are very important issues worldwide. Statistics given by “World Health Organization” are alarming rate of increase in the number of road accidents, most claiming with serious injury, human and material loss. For these reasons has been a continuous development of protection systems, especially car causing three quarters of all accidents. Mathematical modeling and simulation of a car behavior during a frontal collision leads to new solutions in the development of protective systems. This paper presents several structural models of a vehicle during a frontal collision and its behavior is analyzed by numerical simulation using Simulink.

  2. Analysis of car’s frontal collision against pole

    Science.gov (United States)

    Ispas, N.; Nastasoiu, M.

    2017-10-01

    Reducing the effects of traffic accidents over the occupants is a major objective of collision attempts. Impacts between the car and the pole are very dangerous for the physical integrity of the car’s occupants. To minimalize the effects of such events on the passengers of a vehicle, a whole series of efforts by both designers and experienced engineers led to increasingly the vehicles safety. The main aim of these paper is to quantify the influences over the car passengers of loads involved by car against pole collisions using the same car model at different speeds. Also, this kind on occupant influences were study using a small car model. Other goal of the paper was the study of the cars stiffness in frontal collision against the pole. The paper’s experimental results were obtained by support of DSD, Dr. Steffan Datentechnik GmbH - Linz, Austria. The described tests were performed in full test facility of DSD Linz, in “Easter 2016 PC-Crash Seminar”. Cars accelerations, velocities, rotations angles after pole impact were registered and discussed. The novelty of the paper consists in studies referred for the same car model involved in car against pole collisions at different impact speeds. Paper’s conclusions can be future used for car safety improvement.

  3. Study of cervical muscle response and injury of driver during a frontal vehicle collision.

    Science.gov (United States)

    Gao, Zhenhai; Li, Chuzhao; Hu, Hongyu; Zhao, Hui; Chen, Chaoyang; Yu, Huili

    2015-01-01

    Frontal vehicle collisions can cause injury to a driver's cervical muscles resulting from intense changes in muscle strain and muscle load. This study investigated the influence of collision forces in a sled test environment using a modified Hybrid III 50th percentile dummy equipped with simulated spring-type muscles. Cervical muscle responses including strain and load of the sternocleidomastoid (SCM), splenius capitis (SPL), and trapezius (TRP) were analyzed, and muscle injury was assessed. The SCM, SPL, and TRP suffered average peak muscle strains of 21%, 40%, and 23%, respectively, exceeding the injury threshold. The average peak muscle loads of the SCM, SPL and TRP were 11 N, 25 N, and 25 N, respectively, lower than the ultimate failure load. The SPL endured the largest injury, while the injuries to the SCM and TRP were relatively small. This is a preliminary study to assess the cervical muscle of driver during a frontal vehicle collision. This study provides a foundation for investigating the muscle response and injury in sled test environments, which can lead to the improvement of occupant protections.

  4. Effects of cervical arthrodesis and arthroplasty on neck response during a simulated frontal automobile collision.

    Science.gov (United States)

    White, Nicholas A; Moreno, Daniel P; Brown, Philip J; Gayzik, F Scott; Hsu, Wesley; Powers, Alexander K; Stitzel, Joel D

    2014-09-01

    Whereas arthrodesis is the most common surgical intervention for the treatment of symptomatic cervical degenerative disc disease, arthroplasty has become increasingly more popular over the past decade. Although literature exists comparing the effects of anterior cervical discectomy and fusion and cervical total disc replacement (CTDR) on neck kinematics and loading, the vast majority of these studies apply only quasi-static, noninjurious loading conditions to a segment of the cervical spine. The objective of this study was to investigate the effects of arthrodesis and arthroplasty on biomechanical neck response during a simulated frontal automobile collision with air bag deployment. This study used a full-body, 50th percentile seated male finite element (FE) model to evaluate neck response during a dynamic impact event. The cervical spine was modified to simulate either an arthrodesis or arthroplasty procedure at C5-C6. Five simulations of a belted driver, subjected to a 13.3 m/s ΔV frontal impact with air bag deployment, were run in LS-DYNA with the Global Human Body Models Consortium full-body FE model. The first simulation used the original model, with no modifications to the neck, whereas the remaining four were modified to represent either interbody arthrodesis or arthroplasty of C5-C6. Cross-sectional forces and moments at the C5 and C6 cervical levels of the neck, along with interbody and facet forces between C5 and C6, were reported. Adjacent-level, cross-sectional neck loading was maintained in all simulations without exceeding any established injury thresholds. Interbody compression was greatest for the CTDRs, and interbody tension occurred only in the fused and nonmodified spines. Some interbody separation occurred between the superior and inferior components of the CTDRs during flexion-induced tension of the cervical spine, increasing the facet loads. This study evaluated the effects of C5-C6 cervical arthrodesis and arthroplasty on neck response

  5. Collision Welding of Dissimilar Materials by Vaporizing Foil Actuator: A Breakthrough Technology for Dissimilar Metal Joining

    Energy Technology Data Exchange (ETDEWEB)

    Daehn, Glenn S. [The Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering; Vivek, Anupam [The Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering; Liu, Bert C. [The Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering

    2016-09-30

    This work demonstrated and further developed Vaporizing Foil Actuator Welding (VFAW) as a viable technique for dissimilar-metal joining for automotive lightweighting applications. VFAW is a novel impact welding technology, which uses the pressure developed from electrically-assisted rapid vaporization of a thin aluminum foil (the consumable) to launch and ultimately collide two of more pieces of metal to create a solid-state bond between them. 18 dissimilar combinations of automotive alloys from the steel, aluminum and magnesium alloy classes were screened for weldability and characterized by metallography of weld cross sections, corrosion testing, and mechanical testing. Most combinations, especially a good number of Al/Fe pairs, were welded successfully. VFAW was even able to weld combinations of very high strength materials such as 5000 and 6000 series aluminum alloys to boron and dual phase steels, which is difficult to impossible by other joining techniques such as resistance spot welding, friction stir welding, or riveting. When mechanically tested, the samples routinely failed in a base metal rather than along the weld interface, showing that the weld was stronger than either of the base metals. As for corrosion performance, a polymer-based protective coating was used to successfully combat galvanic corrosion of 5 Al/Fe pairs through a month-long exposure to warm salt fog. In addition to the technical capabilities, VFAW also consumes little energy compared to conventional welding techniques and requires relatively light, flexible tooling. Given the technical and economic advantages, VFAW can be a very competitive joining technology for automotive lightweighting. The success of this project and related activities has resulted in substantial interest not only within the research community but also various levels of automotive supply chain, which are collaborating to bring this technology to commercial use.

  6. Mathematical model for studying cyclist kinematics in vehicle-bicycle frontal collisions

    Science.gov (United States)

    Condrea, OA; Chiru, A.; Chiriac, RL; Vlase, S.

    2017-10-01

    For the development of effective vehicle related safety solutions to improve cyclist protection, kinematic predictions are essential. The objective of the paper was the elaboration of a simple mathematical model for predicting cyclist kinematics, with the advantage of yielding simple results for relatively complicated impact situations. Thus, the use of elaborated math software is not required and the calculation time is shortened. The paper presents a modelling framework to determine cyclist kinematic behaviour for the situations in which a M1 category vehicle frontally hits the rear part of a bicycle. After the primary impact between the vehicle front bumper and the bicycle, the cyclist hits the vehicle’s bonnet, the windscreen or both the vehicle’s bonnet and the windscreen in short succession. The head-windshield impact is often the most severe impact, causing serious and potentially lethal injuries. The cyclist is represented by a rigid segment and the equations of motion for the cyclist after the primary impact are obtained by applying Newton’s second law of motion. The impact time for the contact between the vehicle and the cyclist is yielded afterwards by formulating and intersecting the trajectories for two points positioned on the cyclist’s head/body and the vehicle’s windscreen/bonnet while assuming that the cyclist’s equations of motion after the primary impact remain the same. Postimpact kinematics for the secondary impact are yielded by applying linear and angular momentum conservation laws.

  7. The collision of South China with NW India to join Gondwanaland in the Cambrian: Provenance constraints from foreland basins

    Science.gov (United States)

    Yao, W.; Li, Z.; Li, W.; Li, X.; Yang, J.

    2013-12-01

    emerging North India orogen. As the collision progressed, the Wuyi-Yunkai orogen stared to form on the Cathaysia side of the SCB in the Ordovician, shedding sediments to the Nanhua foreland basin. Our provenance results indicate that foreland basin deposits during the Ordovician-Silurian time were mainly recycled Ediacaran-Cambrian sedimentary rocks eroded off the nearby orogen. The Silurian strata also recorded contributions from late orogenic magmatism, possibly formed during the orogenic collapse.

  8. Ceramic joining

    Energy Technology Data Exchange (ETDEWEB)

    Loehman, R.E. [Sandia National Lab., Albuquerque, NM (United States)

    1996-04-01

    This paper describes the relation between reactions at ceramic-metal interfaces and the development of strong interfacial bonds in ceramic joining. Studies on a number of systems are described, including silicon nitrides, aluminium nitrides, mullite, and aluminium oxides. Joints can be weakened by stresses such as thermal expansion mismatch. Ceramic joining is used in a variety of applications such as solid oxide fuel cells.

  9. Joining Forces

    DEFF Research Database (Denmark)

    Christiansen, Anne Mette

    2013-01-01

    The interest in Corporate Social Responsibility (CSR) has grown dramatically over the last three years in Greenland. A vast geographical area with a tiny population, Greenland has recently obtained self-government status and is going through a rapid development economically and socially...... as the country moves towards embracing extractive industries (oil, gas and mining) as a path to development. Both government, civil society and business are increasingly looking for new and innovative ways of joining forces across sectors to solve some of the country's many critical social issues. Greenlandic...... companies have over the last 23 years embraced the concept of strategic CSR and are increasingly engaging in cross-sector partnerships as part of their CSR strategy. The partnerships take different forms both in regards to number of partners, focus areas and level of strategic engagement. In the article...

  10. The early argument for prefrontal leucotomy: the collision of frontal lobe theory and psychosurgery at the 1935 International Neurological Congress in London.

    Science.gov (United States)

    Boettcher, Lillian B; Menacho, Sarah T

    2017-09-01

    The pathophysiology of mental illness and its relationship to the frontal lobe were subjects of immense interest in the latter half of the 19th century. Numerous studies emerged during this time on cortical localization and frontal lobe theory, drawing upon various ideas from neurology and psychiatry. Reflecting the intense interest in this region of the brain, the 1935 International Neurological Congress in London hosted a special session on the frontal lobe. Among other presentations, Yale physiologists John Fulton and Carlyle Jacobsen presented a study on frontal lobectomy in primates, and neurologist Richard Brickner presented a case of frontal ablation for olfactory meningioma performed by the Johns Hopkins neurosurgeon Walter Dandy. Both occurrences are said to have influenced Portuguese neurologist Egas Moniz (1874-1955) to commence performing leucotomies on patients beginning in late 1935. Here the authors review the relevant events related to frontal lobe theory leading up to the 1935 Neurological Congress as well as the extent of this meeting's role in the genesis of the modern era of psychosurgery.

  11. Joining of advanced materials

    CERN Document Server

    Messler, Robert W

    1993-01-01

    Provides an unusually complete and readable compilation of the primary and secondary options for joining conventional materials in non-conventional ways. Provides unique coverage of adhesive bonding using both organic and inorganic adhesives, cements and mortars. Focuses on materials issues without ignoring issues related to joint design, production processing, quality assurance, process economics, and joining performance in service.Joining of advanced materials is a unique treatment of joining of both conventional and advanced metals andalloys, intermetallics, ceramics, glasses, polymers, a

  12. Joining by plastic deformation

    DEFF Research Database (Denmark)

    Mori, Ken-ichiro; Bay, Niels; Fratini, Livan

    2013-01-01

    opportunities to design new products through joining dissimilar materials. This paper aims to provide an overview of the state of the art in such joining processes, including cold welding, friction stir welding, self-pierce riveting, mechanical clinching and joining by forming. The paper includes description...

  13. Precision Joining Center

    Science.gov (United States)

    Powell, J. W.; Westphal, D. A.

    1991-08-01

    A workshop to obtain input from industry on the establishment of the Precision Joining Center (PJC) was held on July 10-12, 1991. The PJC is a center for training Joining Technologists in advanced joining techniques and concepts in order to promote the competitiveness of U.S. industry. The center will be established as part of the DOE Defense Programs Technology Commercialization Initiative, and operated by EG&G Rocky Flats in cooperation with the American Welding Society and the Colorado School of Mines Center for Welding and Joining Research. The overall objectives of the workshop were to validate the need for a Joining Technologists to fill the gap between the welding operator and the welding engineer, and to assure that the PJC will train individuals to satisfy that need. The consensus of the workshop participants was that the Joining Technologist is a necessary position in industry, and is currently used, with some variation, by many companies. It was agreed that the PJC core curriculum, as presented, would produce a Joining Technologist of value to industries that use precision joining techniques. The advantage of the PJC would be to train the Joining Technologist much more quickly and more completely. The proposed emphasis of the PJC curriculum on equipment intensive and hands-on training was judged to be essential.

  14. Common Influence Join

    DEFF Research Database (Denmark)

    Yiu, Man Lung; Mamoulis, Nikos; Karras, Panagiotis

    2008-01-01

    We identify and formalize a novel join operator for two spatial pointsets P and Q. The common influence join (CIJ) returns the pairs of points (p,q),p isin P,q isin Q, such that there exists a location in space, being closer to p than to any other point in P and at the same time closer to q than...

  15. Joined and Responsible Parenting

    Directory of Open Access Journals (Sweden)

    Selmani-Bakiu Arta

    2017-06-01

    Full Text Available In the contemporary family law, parents are obliged to arrange the joined implementation of the parenting rights either by their own will or through the help of their lawyers and/or mediators. This institute of mutual agreement is known as joined custody or joined implementation of the parenting right after the divorce of the marriage. This institute makes it possible for parents who live separately to arrange their custody rights in the most convenient way for the child. With a joined custody agreement, the parents accept the obligation to implement all the rights and duties that constitute the parenting right even in case of their separation. Through not dividing their rights from their obligations and with the aim of being closer to the needs of the child, the institute of joined custody helps avoid the feelings of hostility and disagreement in regard to the judicial decision which gives permanent custody to one of the parents. This institute is incorporated in the family law of many countries (Sweden, Norway, Finland, Denmark, UK, France, Italy, Germany, Belgium, Switzerland, Hungary, Czech Republic, USA and Australia. This article aims to emphasize the need to introduce in the family law of RM an explicit provision for joined and responsible custody after the divorce in order to achieve the best interest of the child. There is a joined initiative of parents who live separately from their children who request the amendment of the Family Law of RM in this direction.

  16. Joining uranium to steel

    International Nuclear Information System (INIS)

    Perkins, M.A.

    1976-05-01

    A method has been devised which will allow the joining of uranium to steel by fusion welding through the use of an intermediate material. Uranium-0.5 titanium was joined to AISI 304L stainless steel by using a vanadium insert. Also, a method is now available for selecting possible filler metals when two entirely dissimilar metals need to be joined. This method allows a quantitative ranking to be made of the possible filler metals and thus the most likely candidate can be selected

  17. Pulse joining cartridges

    Energy Technology Data Exchange (ETDEWEB)

    Golovashchenko, Sergey Fedorovich; Bonnen, John Joseph Francis

    2017-09-26

    A pulsed joining tool includes a tool body that defines a cavity that receives an inner tubular member and an outer tubular member and a pulse joining cartridge. The tubular members are nested together with the cartridge being disposed around the outer tubular member. The cartridge includes a conductor, such as a wire or foil, that extends around the outer tubular member and is insulated to separate a supply segment from a return segment. A source of stored electrical energy is discharged through the conductor to join the tubular members with an electromagnetic force pulse.

  18. Ring-constrained Join

    DEFF Research Database (Denmark)

    Yiu, Man Lung; Karras, Panagiotis; Mamoulis, Nikos

    2008-01-01

    We introduce a novel spatial join operator, the ring-constrained join (RCJ). Given two sets P and Q of spatial points, the result of RCJ consists of pairs (p, q) (where p ε P, q ε Q) satisfying an intuitive geometric constraint: the smallest circle enclosing p and q contains no other points in P, Q....... This new operation has important applications in decision support, e.g., placing recycling stations at fair locations between restaurants and residential complexes. Clearly, RCJ is defined based on a geometric constraint but not on distances between points. Thus, our operation is fundamentally different...... from the conventional distance joins and closest pairs problems. We are not aware of efficient processing algorithms for RCJ in the literature. A brute-force solution requires computational cost quadratic to input size and it does not scale well for large datasets. In view of this, we develop efficient...

  19. Lower limb and associated injuries in frontal-impact road traffic ...

    African Journals Online (AJOL)

    Abstract. Objectives: To study the relationship between severity of injury of the lower limb and severity of injury of the head, thoracic, and abdominal regions in frontal-impact road traffic collisions. Methods: Consecutive hospitalised trauma patients who were involved in a frontal road traffic collision were prospectively stud-.

  20. On the Complexity of Inner Product Similarity Join

    DEFF Research Database (Denmark)

    Ahle, Thomas Dybdahl; Pagh, Rasmus; Razenshteyn, Ilya

    2016-01-01

    A number of tasks in classification, information retrieval, recommendation systems, and record linkage reduce to the core problem of inner product similarity join (IPS join): identifying pairs of vectors in a collection that have a sufficiently large inner product. IPS join is well understood when...... bounds for (A)LSH-based algorithms. In particular, we show that asymmetry can be avoided by relaxing the LSH definition to only consider the collision probability of distinct elements. A new indexing method for IPS based on linear sketches, implying that our hardness results are not far from being tight...

  1. Recent progress in ceramic joining

    Energy Technology Data Exchange (ETDEWEB)

    Loehman, R.E.

    1998-09-01

    Both fundamental and practical aspects of ceramic joining are understood well enough for many, if not most, applications requiring moderate strengths at room temperature. This paper argues that the two greatest needs in ceramic joining are for techniques to join buried interfaces by selective heating, and methods for joining ceramics for use at temperatures of 800 to 1,200 C. Heating with microwave radiation or with high-energy electron beams has been used to join buried ceramic interfaces, for example SiC to SiC. Joints with varying levels of strength at temperatures of 600 to 1,000 C have been made using four techniques: (1) transient liquid phase bonding; (2) joining with refractory braze alloys; (3) joining with refractory glass compositions; and (4) joining using preceramic polymers. Joint strengths as high as 550 MPa at 1,000 C have been reported for silicon nitride-silicon nitride bonds tested in four-point flexure.

  2. Fast and scalable inequality joins

    KAUST Repository

    Khayyat, Zuhair

    2016-09-07

    Inequality joins, which is to join relations with inequality conditions, are used in various applications. Optimizing joins has been the subject of intensive research ranging from efficient join algorithms such as sort-merge join, to the use of efficient indices such as (Formula presented.)-tree, (Formula presented.)-tree and Bitmap. However, inequality joins have received little attention and queries containing such joins are notably very slow. In this paper, we introduce fast inequality join algorithms based on sorted arrays and space-efficient bit-arrays. We further introduce a simple method to estimate the selectivity of inequality joins which is then used to optimize multiple predicate queries and multi-way joins. Moreover, we study an incremental inequality join algorithm to handle scenarios where data keeps changing. We have implemented a centralized version of these algorithms on top of PostgreSQL, a distributed version on top of Spark SQL, and an existing data cleaning system, Nadeef. By comparing our algorithms against well-known optimization techniques for inequality joins, we show our solution is more scalable and several orders of magnitude faster. © 2016 Springer-Verlag Berlin Heidelberg

  3. Join Operations in Temporal Databases

    DEFF Research Database (Denmark)

    Gao, D.; Jensen, Christian Søndergaard; Snodgrass, R.T.

    2005-01-01

    Joins are arguably the most important relational operators. Poor implementations are tantamount to computing the Cartesian product of the input relations. In a temporal database, the problem is more acute for two reasons. First, conventional techniques are designed for the evaluation of joins wit...... to implementation, is on non-index-based join algorithms. Such algorithms do not rely on auxiliary access paths but may exploit sort orderings to achieve efficiency......., if any, comparison of the various operators. We then address evaluation algorithms, comparing the applicability of various algorithms to the temporal join operators and describing a performance study involving algorithms for one important operator, the temporal equijoin. Our focus, with respect...

  4. On the Expressiveness of Joining

    Directory of Open Access Journals (Sweden)

    Thomas Given-Wilson

    2015-08-01

    Full Text Available The expressiveness of communication primitives has been explored in a common framework based on the pi-calculus by considering four features: synchronism (asynchronous vs synchronous, arity (monadic vs polyadic data, communication medium (shared dataspaces vs channel-based, and pattern-matching (binding to a name vs testing name equality vs intensionality. Here another dimension coordination is considered that accounts for the number of processes required for an interaction to occur. Coordination generalises binary languages such as pi-calculus to joining languages that combine inputs such as the Join Calculus and general rendezvous calculus. By means of possibility/impossibility of encodings, this paper shows coordination is unrelated to the other features. That is, joining languages are more expressive than binary languages, and no combination of the other features can encode a joining language into a binary language. Further, joining is not able to encode any of the other features unless they could be encoded otherwise.

  5. Join Operations in Temporal Databases

    DEFF Research Database (Denmark)

    Gao, D.; Jensen, Christian Søndergaard; Snodgrass, R.T.

    2005-01-01

    with equality predicates rather than the inequality predicates prevalent in valid-time queries. Second, the presence of temporally varying data dramatically increases the size of a database. These factors indicate that specialized techniques are needed to efficiently evaluate temporal joins. We address......, if any, comparison of the various operators. We then address evaluation algorithms, comparing the applicability of various algorithms to the temporal join operators and describing a performance study involving algorithms for one important operator, the temporal equijoin. Our focus, with respect...... to implementation, is on non-index-based join algorithms. Such algorithms do not rely on auxiliary access paths but may exploit sort orderings to achieve efficiency....

  6. HIP Joining of Cemented Carbides

    Energy Technology Data Exchange (ETDEWEB)

    Derby, B.; Miodownik, M.

    1999-04-01

    Hot Isostatic Pressing (HIP) is investigated as a technique for joining the cermet WC-15% Co to itself. Encapsulation of the specimens prior to HIPing was carried out using steel encapsulation, glass encapsulation and self encapsulation. The bonds were evaluated using a four point bend method. It is shown that the glass and steel encapsulation methods have a number of inherent problems which make them inappropriate for near net shape processing. In contrast the novel self encapsulation method, described for the first time in this communication, is both simple and effective, producing joined material with bulk strength. The concept of self encapsulation is potentially widely applicable for joining composite materials.

  7. CORRELATION ANALYSIS OF VEHICLE FRONTAL IMPACT PARAMETERS

    Directory of Open Access Journals (Sweden)

    Josef Mík

    2017-12-01

    Full Text Available The article considers a possible improvement of road vehicle safety by using eCall – a system which initiates an emergency call in case of traffic accident. A possible way of better description of a frontal impact accident of a vehicle is examined and enriched by the information from the onboard e-call unit. In this article, we analyze results of frontal crash tests with different types of barriers and overlapping area and look for the correlation between the individual vehicle and collision parameters in order to provide a better description of the severity of the accident by the eCall system. The relation among the selected parameters is described using the correlation analysis.

  8. Blind-date Conversation Joining

    Directory of Open Access Journals (Sweden)

    Luca Cesari

    2013-07-01

    Full Text Available We focus on a form of joining conversations among multiple parties in service-oriented applications where a client may asynchronously join an existing conversation without need to know in advance any information about it. More specifically, we show how the correlation mechanism provided by orchestration languages enables a form of conversation joining that is completely transparent to clients and that we call 'blind-date joining'. We provide an implementation of this strategy by using the standard orchestration language WS-BPEL. We then present its formal semantics by resorting to COWS, a process calculus specifically designed for modelling service-oriented applications. We illustrate our approach by means of a simple, but realistic, case study from the online games domain.

  9. Mesial frontal lobe epilepsy.

    Science.gov (United States)

    Unnwongse, Kanjana; Wehner, Tim; Foldvary-Schaefer, Nancy

    2012-10-01

    Mesial frontal lobe epilepsies can be divided into epilepsies arising from the anterior cingulate gyrus and those of the supplementary sensorimotor area. They provide diagnostic challenges because they often lack lateralizing or localizing features on clinical semiology and interictal and ictal scalp electroencephalographic (EEG) recordings. A number of unique semiologic features have been described over the last decade in patients with mesial frontal lobe epilepsy (FLE). There are few reports of applying advanced neurophysiologic techniques such as electrical source imaging, magnetoencephalography, EEG/functional magnetic resonance imaging, or analysis of high-frequency oscillations in patients with mesial FLE. Despite these diagnostic challenges, it seems that patients with mesial FLE benefit from epilepsy surgery to the same extent or even better than patients with FLE do, as a whole.

  10. BlockJoin : Efficient Matrix Partitioning Through Joins

    NARCIS (Netherlands)

    Kunft, Andreas; Katsifodimos, A.; Schelter, Sebastian; Rabl, Tilmann; Markl, Volker; Boncz, Peter; Salem, Ken

    2017-01-01

    Linear algebra operations are at the core of many Machine Learning (ML) programs. At the same time, a considerable amount of the effort for solving data analytics problems is spent in data preparation. As a result, end-to- end ML pipelines often consist of (i) relational operators used for joining

  11. Posttraumatic frontal bone osteomyelitis.

    Science.gov (United States)

    Jung, S Heredero; Aniceto, G Sánchez; Rodríguez, I Zubillaga; Diaz, R Gutiérrez; Recuero, I I García

    2009-05-01

    We present the clinical case of a patient with open bilateral frontal sinus fractures who developed a frontal osteomyelitis. A review of the problem and management ascending to the different alternatives for central anterior skull base defects and fronto-orbital reconstruction is also presented. After extensive radical debridement of the necrotic bone, final reconstruction of the skull base was performed by using a rectus abdominis free flap. A custom-made hard tissue replacement implant was used for the fronto-orbital reconstruction. Extensive debridement is required for the treatment of frontal osteomyelitis. An appropriate isolation of the skull base from the upper aerodigestive system must be obtained to prevent continuous infectious complications. Free flaps are especially useful for skull base reconstruction when traditional methods are not available or have failed because of the lack of available tissue for vascularized reconstruction. Custom-made alloplastic implants are a good reconstructive option for large fronto-orbital defects once the infection is gone and vascularized tissue has been transferred.

  12. Dorsolateral frontal lobe epilepsy.

    Science.gov (United States)

    Lee, Ricky W; Worrell, Greg A

    2012-10-01

    Dorsolateral frontal lobe seizures often present as a diagnostic challenge. The diverse semiologies may not produce lateralizing or localizing signs and can appear bizarre and suggest psychogenic events. Unfortunately, scalp electroencephalographic (EEG) and magnetic resonance imaging (MRI) are often unsatisfactory. It is not uncommon that these traditional diagnostic studies are either unhelpful or even misleading. In some cases, SPECT and positron emission tomography imaging can be an effective tool to identify the origin of seizures. However, these techniques and other emerging techniques all have limitations, and new approaches are needed to improve source localization.

  13. Frontal Integration and Coping

    DEFF Research Database (Denmark)

    Larsen, Torben

    2012-01-01

    and risk minimizing Rationalists dominated by dlPFC • R correlates both with your own level of education and that of your parents 3 Conclusion: Empirical verification of the first derivative of NeM uncovers four different coping patterns within the range of normal behaviors with an obvious analogue...... to the classical tempers. In prospect, differentiating the Frontal integration pattern by temper (General risk attitude) opens an evidence-based pathway for individually tailored neural training towards advanced social objectives as multidisciplinary collaboration and healthy living. References 1. Larsen T...... et al. Gender difference in neural response to psychological stress. SCAN 2 2007, 227–233...

  14. Chrysler Upset Protrusion Joining Techniques for Joining Dissimilar Metals

    Energy Technology Data Exchange (ETDEWEB)

    Logan, Stephen [FCA US LLC, Auburn Hills, MI (United States)

    2017-09-28

    The project goal was to develop and demonstrate a robust, cost effective, and versatile joining technique, known as Upset Protrusion Joining (UPJ), for joining challenging dissimilar metal com-binations, especially those where one of the metals is a die cast magnesium (Mg) component. Since two of the key obstacles preventing more widespread use of light metals (especially in high volume automotive applications) are 1) a lack of robust joining techniques and 2) susceptibility to galvanic corrosion, and since the majority of the joint combinations evaluated in this project include die cast Mg (the lightest structural metal) as one of the two materials being joined, and since die casting is the most common and cost effective process for producing Mg components, then successful project completion provides a key enabler to high volume application of lightweight materials, thus potentially leading to reduced costs, and encouraging implementation of lightweight multi-material vehicles for significant reductions in energy consumption and reduced greenhouse gas emissions. Eco-nomic benefits to end-use consumers are achieved primarily via the reduction in fuel consumption. Unlike currently available commercial processes, the UPJ process relies on a very robust mechanical joint rather than intermetallic bonding, so the more cathodic material can be coated prior to joining, thus creating a robust isolation against galvanic attack on the more anodic material. Additionally, since the UPJ protrusion is going through a hole that can be pre-drilled or pre-punched prior to coating, the UPJ process is less likely to damage the coating when the joint is being made. Further-more, since there is no additional cathodic material (such as a steel fastener) used to create the joint, there is no joining induced galvanic activity beyond that of the two parent materials. In accordance with its originally proposed plan, this project has successfully developed process variants of UPJ to enable

  15. Joining ceramics, glass and metal

    International Nuclear Information System (INIS)

    Kraft, W.

    1989-01-01

    In many areas of electronics, engine manufacturing, machine and apparatus construction and aearospace, different combinations of materials such as ceramics/metal and glass/metal are gaining increasingly in importance. The proceedings cover the 53 papers presented to the 3rd International Conference on Joining Ceramics, Glass and Metal, held in Bad Nauheim (FRG) from April 26 to 28, 1989. The papers discuss problems and results under the following main topics of the conference: (1) Active brazing applied to non-oxide ceramics and oxide ceramics. (2) Diffusion bonding of metals and ceramics. (3) Friction welding, reaction bonding, and other joining methods. (4) Properties of metal-ceramic joints (as e.g. residual stress, fracture toughness, thermal stress) and various investigation methods for their determination. (MM) [de

  16. Analysis of 86 fatal motorcycle frontal crashes in

    Directory of Open Access Journals (Sweden)

    ZHAO Hui

    2012-06-01

    Full Text Available 【Abstract】Objective: To analyze the injuries of motorcyclists involved in fatal motorcycle frontal crashes. Methods: A survey group involving multi-discipline experts was built to randomly collect data on fatal motor-cycle frontal collision accidents that occurred in Chongqing during 2006-2010. The sampled information included medi-cal or autopsy reports, blood alcohol concentration (BAC level, helmet use, accident witness, field sketch as well as field photos. The motorcyclist injuries were scored accord-ing to the Abbreviated Injury Scale (AIS 2005. The involved riders with a BAC level≥20 mg/ml were attributed to alco-hol use. Data were processed statistically with nonparamet-ric test via software SPSS 11.0. Results: A total of 86 fatal motorcycle frontal crashes were sampled and further analyzed. The age of motorcy-clists enrolled in this investigation showed nominal distri-bution and the middle-aged (30-39 years occupied the high-est percentage of fatalities. There were only 14 motorcyclists (16.3% wearing helmets at the moment of collision. And 12.8% of these motorcyclist crashes were attributable to alcohol use. Impact injury was the main fatal cause, accounting for 72% of motorcyclist deaths, followed by tumbling injury (26% and run-over (2%. Respectively 84%, 22% and 19% of motorcyclists who sustained head, chest and abdominal trauma died. Extremity injury was the most frequently ob-served injury type. Conclusions: This investigation is helpful to build accident prevention programs and develop protection de-vices which may effectively mitigate injuries and prevent deaths following motorcycle frontal collision accidents. Further investigations on motorcycle collision accidents are still needed. Key words: Motorcycles; Mortality; Accidents, traffic; Wounds and injuries

  17. Frontal mucocele with intracranial extension causing frontal lobe syndrome.

    Science.gov (United States)

    Weidmayer, Sara

    2015-06-01

    Mucoceles are mucus-containing cysts that form in paranasal sinuses; although mucoceles themselves are benign, this case report highlights the extensive damage they can cause as their expansion may lead to bony erosion and extension of the mucocele into the orbit and cranium; it also presents a rarely reported instance of frontal sinus mucocele leading to frontal lobe syndrome. A thorough discussion and review of mucoceles is included. A 68-year-old white man presented with intermittent diplopia and a pressure sensation in the right eye. He had a history of chronic sinusitis and had had endoscopic sinus surgery 5 years prior. A maxillofacial computed tomography scan revealed a large right frontal sinus mucocele, which had caused erosion along the medial wall of the right orbit and the outer and inner tables of the right frontal sinus. The mucocele had protruded both into the right orbit and intracranially, causing mass effect on the frontal lobe, which led to frontal lobe syndrome. The patient was successfully treated with endoscopic right ethmoidectomy, radial frontal sinusotomy, marsupialization of the mucocele, and transcutaneous irrigation. Paranasal sinus mucoceles may expand and lead to bony erosion and can become very invasive in surrounding structures such as the orbit and cranium. This case not only exhibits a very rare presentation of frontal sinus mucocele with intracranial extension and frontal lobe mass effect causing a frontal lobe syndrome but also demonstrates many of the ocular and visual complications commonly associated with paranasal sinus mucoceles. Early identification and surgical intervention is vital for preventing and reducing morbidity associated with invasive mucoceles, and the patient must be followed regularly to monitor for recurrence.

  18. Lightning fast and space efficient inequality joins

    KAUST Repository

    Khayyat, Zuhair

    2015-09-01

    Inequality joins, which join relational tables on inequality conditions, are used in various applications. While there have been a wide range of optimization methods for joins in database systems, from algorithms such as sort-merge join and band join, to various indices such as B+-tree, R*-tree and Bitmap, inequality joins have received little attention and queries containing such joins are usually very slow. In this paper, we introduce fast inequality join algorithms. We put columns to be joined in sorted arrays and we use permutation arrays to encode positions of tuples in one sorted array w.r.t. the other sorted array. In contrast to sort-merge join, we use space efficient bit-arrays that enable optimizations, such as Bloom filter indices, for fast computation of the join results. We have implemented a centralized version of these algorithms on top of PostgreSQL, and a distributed version on top of Spark SQL. We have compared against well known optimization techniques for inequality joins and show that our solution is more scalable and several orders of magnitude faster.

  19. Lightning Fast and Space Efficient Inequality Joins

    KAUST Repository

    Khayyat, Zuhair

    2015-09-01

    Inequality joins, which join relational tables on inequality conditions, are used in various applications. While there have been a wide range of optimization methods for joins in database systems, from algorithms such as sort-merge join and band join, to various indices such as B+-tree,R*-tree and Bitmap, inequality joins have received little attention and queries containing such joins are usually very slow. In this paper, we introduce fast inequality join algorithms. We put columns to be joined in sorted arrays and we use permutation arrays to encode positions of tuples in one sorted array w.r.t. the other sorted array. In contrast to sort-merge join, we use space effcient bit-arrays that enable optimizations, such as Bloom filter indices, for fast computation of the join results. We have implemented a centralized version of these algorithms on top of PostgreSQL, and a distributed version on top of Spark SQL. We have compared against well known optimization techniques for inequality joins and show that our solution is more scalable and several orders of magnitude faster.

  20. Flexible Friction Stir Joining Technology

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Zhili [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lim, Yong Chae [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mahoney, Murray [MegaStir Technologies LLC, Orem, UT (United States); Sanderson, Samuel [MegaStir Technologies LLC, Orem, UT (United States); Larsen, Steve [MegaStir Technologies LLC, Orem, UT (United States); Steel, Russel [MegaStir Technologies LLC, Orem, UT (United States); Fleck, Dale [MegaStir Technologies LLC, Orem, UT (United States); Fairchild, Doug P [ExxonMobil, Upstream Research Company (URC), Houston, TX (United States); Wasson, Andrew J [ExxonMobil, Upstream Research Company (URC), Houston, TX (United States); Babb, Jon [MegaStir Technologies LLC, Orem, UT (United States); Higgins, Paul [MegaStir Technologies LLC, Orem, UT (United States)

    2015-07-23

    Reported herein is the final report on a U.S. Department of Energy (DOE) Advanced Manufacturing Office (AMO) project with industry cost-share that was jointly carried out by Oak Ridge National Laboratory (ORNL), ExxonMobil Upstream Research Company (ExxonMobil), and MegaStir Technologies (MegaStir). The project was aimed to advance the state of the art of friction stir welding (FSW) technology, a highly energy-efficient solid-state joining process, for field deployable, on-site fabrications of large, complex and thick-sectioned structures of high-performance and high-temperature materials. The technology innovations developed herein attempted to address two fundamental shortcomings of FSW: 1) the inability for on-site welding and 2) the inability to weld thick section steels, both of which have impeded widespread use of FSW in manufacturing. Through this work, major advance has been made toward transforming FSW technology from a “specialty” process to a mainstream materials joining technology to realize its pervasive energy, environmental, and economic benefits across industry.

  1. Why join the Staff Association

    CERN Multimedia

    Association du personnel

    2011-01-01

    Becoming a member of the Staff Association (SA) is above all a personal choice, showing that the joining person’s commitment and adherence to values such as solidarity, social cohesion, etc.In September, the SA launches a membership campaign to convince a maximum number to join, to inform, arouse interest and support. Posters, emails and individual contacts are part of the campaign programme, just like this editorial. As far as individual contacts are concerned, we ask you to give time and lend an ear to the delegates of your department in the Staff Council, who will approach you, in order to make an open and constructive discussion possible. Do not hesitate to ask questions and let them know your thoughts about the SA, as (constructive) criticism enables us to progress. The Staff Association and its role of collective representation The Staff Association, via its delegates, represents collectively all staff of the Organization before the Director-General and Member States. To do this, staff rep...

  2. Origami by frontal photopolymerization.

    Science.gov (United States)

    Zhao, Zeang; Wu, Jiangtao; Mu, Xiaoming; Chen, Haosen; Qi, H Jerry; Fang, Daining

    2017-04-01

    Origami structures are of great interest in microelectronics, soft actuators, mechanical metamaterials, and biomedical devices. Current methods of fabricating origami structures still have several limitations, such as complex material systems or tedious processing steps. We present a simple approach for creating three-dimensional (3D) origami structures by the frontal photopolymerization method, which can be easily implemented by using a commercial projector. The concept of our method is based on the volume shrinkage during photopolymerization. By adding photoabsorbers into the polymer resin, an attenuated light field is created and leads to a nonuniform curing along the thickness direction. The layer directly exposed to light cures faster than the next layer; this nonuniform curing degree leads to nonuniform curing-induced volume shrinkage. This further introduces a nonuniform stress field, which drives the film to bend toward the newly formed side. The degree of bending can be controlled by adjusting the gray scale and the irradiation time, an easy approach for creating origami structures. The behavior is examined both experimentally and theoretically. Two methods are also proposed to create different types of 3D origami structures.

  3. Parallel trajectory similarity joins in spatial networks

    KAUST Repository

    Shang, Shuo

    2018-04-04

    The matching of similar pairs of objects, called similarity join, is fundamental functionality in data management. We consider two cases of trajectory similarity joins (TS-Joins), including a threshold-based join (Tb-TS-Join) and a top-k TS-Join (k-TS-Join), where the objects are trajectories of vehicles moving in road networks. Given two sets of trajectories and a threshold θ, the Tb-TS-Join returns all pairs of trajectories from the two sets with similarity above θ. In contrast, the k-TS-Join does not take a threshold as a parameter, and it returns the top-k most similar trajectory pairs from the two sets. The TS-Joins target diverse applications such as trajectory near-duplicate detection, data cleaning, ridesharing recommendation, and traffic congestion prediction. With these applications in mind, we provide purposeful definitions of similarity. To enable efficient processing of the TS-Joins on large sets of trajectories, we develop search space pruning techniques and enable use of the parallel processing capabilities of modern processors. Specifically, we present a two-phase divide-and-conquer search framework that lays the foundation for the algorithms for the Tb-TS-Join and the k-TS-Join that rely on different pruning techniques to achieve efficiency. For each trajectory, the algorithms first find similar trajectories. Then they merge the results to obtain the final result. The algorithms for the two joins exploit different upper and lower bounds on the spatiotemporal trajectory similarity and different heuristic scheduling strategies for search space pruning. Their per-trajectory searches are independent of each other and can be performed in parallel, and the mergings have constant cost. An empirical study with real data offers insight in the performance of the algorithms and demonstrates that they are capable of outperforming well-designed baseline algorithms by an order of magnitude.

  4. Temporary Frontal Paralysis Secondary to Blunt Trauma Frontal Sinus Fracture

    Science.gov (United States)

    Hamilton, Stefan; Hearn, Matthew; Kherani, Safeena; Macdonald, Kristian I.

    2017-01-01

    Frontal sinus fractures (FSF) are relatively uncommon and can be challenging for trauma surgeons to manage. Patients with FSF typically present with facial swelling, pain, and nasofrontal ecchymosis. Here we present a rare case of a patient with FSF and anterior table fracture where the main presenting symptom was bilateral frontal paralysis. We outline our management strategy and review the current literature in regard to management of FSF. PMID:28573060

  5. Collision thrills

    DEFF Research Database (Denmark)

    Larsen, Lasse Juel

    2016-01-01

    . The working hypothesis is that the aesthetics of action and the affinities between medias centre on collision. It will be suggested that collisions produce thrills ranging from the pleasure of destruction to the experience of spatial disorientation. Following will the aesthetics of action be coined ‘collision...

  6. ITER oriented issues-1 (joining)

    International Nuclear Information System (INIS)

    Gervash, A.; Mazul, I.; Litunovsky, N.; Pokrovsky, A.

    2004-01-01

    Proposing beryllium as plasma facing armor and fast brazing as Be/Cu-alloy joining technique, this paper presents the recent experimental results. It was shown that fast brazing of Be onto both PH-copper like CuCrZr and DS (Dispersion Strengthen)-copper like GlidCop provides reliable joint that does not failure under heat flux up to melting of Be surface. Investigating the influence of neutron irradiation on Be/Cu-alloy joint behavior, in-pile integrated test in a core of nuclear reactor CN-2, Dimitrovgrad, Russia was carried out. In this test actively cooled Be/CuCrZr and Be/GildCop joints were simultaneously subjected to high heat flux (1000 cycles, ∼7.5 MW/m 2 ) and neutron irradiation (total 2.8 x 10 20 n/cm 2 , ∼0.13 dpa). Both type of tested joints successfully survived applied heat and neutron loads. Optic and TEM metallography before and after irradiation as well as micro harness measurements are presented and discussed. (author)

  7. Authenticated join processing in outsourced databases

    KAUST Repository

    Yang, Yin

    2009-01-01

    Database outsourcing requires that a query server constructs a proof of result correctness, which can be verified by the client using the data owner\\'s signature. Previous authentication techniques deal with range queries on a single relation using an authenticated data structure (ADS). On the other hand, authenticated join processing is inherently more complex than ranges since only the base relations (but not their combination) are signed by the owner. In this paper, we present three novel join algorithms depending on the ADS availability: (i) Authenticated Indexed Sort Merge Join (AISM), which utilizes a single ADS on the join attribute, (ii) Authenticated Index Merge Join (AIM) that requires an ADS (on the join attribute) for both relations, and (iii) Authenticated Sort Merge Join (ASM), which does not rely on any ADS. We experimentally demonstrate that the proposed methods outperform two benchmark algorithms, often by several orders of magnitude, on all performance metrics, and effectively shift the workload to the outsourcing service. Finally, we extend our techniques to complex queries that combine multi-way joins with selections and projections. ©2009 ACM.

  8. Efficient Joins with Compressed Bitmap Indexes

    Energy Technology Data Exchange (ETDEWEB)

    Computational Research Division; Madduri, Kamesh; Wu, Kesheng

    2009-08-19

    We present a new class of adaptive algorithms that use compressed bitmap indexes to speed up evaluation of the range join query in relational databases. We determine the best strategy to process a join query based on a fast sub-linear time computation of the join selectivity (the ratio of the number of tuples in the result to the total number of possible tuples). In addition, we use compressed bitmaps to represent the join output compactly: the space requirement for storing the tuples representing the join of two relations is asymptotically bounded by min(h; n . cb), where h is the number of tuple pairs in the result relation, n is the number of tuples in the smaller of the two relations, and cb is the cardinality of the larger column being joined. We present a theoretical analysis of our algorithms, as well as experimental results on large-scale synthetic and real data sets. Our implementations are efficient, and consistently outperform well-known approaches for a range of join selectivity factors. For instance, our count-only algorithm is up to three orders of magnitude faster than the sort-merge approach, and our best bitmap index-based algorithm is 1.2x-80x faster than the sort-merge algorithm, for various query instances. We achieve these speedups by exploiting several inherent performance advantages of compressed bitmap indexes for join processing: an implicit partitioning of the attributes, space-efficiency, and tolerance of high-cardinality relations.

  9. Welding and Joining of Titanium Aluminides

    Science.gov (United States)

    Cao, Jian; Qi, Junlei; Song, Xiaoguo; Feng, Jicai

    2014-01-01

    Welding and joining of titanium aluminides is the key to making them more attractive in industrial fields. The purpose of this review is to provide a comprehensive overview of recent progress in welding and joining of titanium aluminides, as well as to introduce current research and application. The possible methods available for titanium aluminides involve brazing, diffusion bonding, fusion welding, friction welding and reactive joining. Of the numerous methods, solid-state diffusion bonding and vacuum brazing have been most heavily investigated for producing reliable joints. The current state of understanding and development of every welding and joining method for titanium aluminides is addressed respectively. The focus is on the fundamental understanding of microstructure characteristics and processing–microstructure–property relationships in the welding and joining of titanium aluminides to themselves and to other materials. PMID:28788113

  10. Welding and Joining of Titanium Aluminides

    Directory of Open Access Journals (Sweden)

    Jian Cao

    2014-06-01

    Full Text Available Welding and joining of titanium aluminides is the key to making them more attractive in industrial fields. The purpose of this review is to provide a comprehensive overview of recent progress in welding and joining of titanium aluminides, as well as to introduce current research and application. The possible methods available for titanium aluminides involve brazing, diffusion bonding, fusion welding, friction welding and reactive joining. Of the numerous methods, solid-state diffusion bonding and vacuum brazing have been most heavily investigated for producing reliable joints. The current state of understanding and development of every welding and joining method for titanium aluminides is addressed respectively. The focus is on the fundamental understanding of microstructure characteristics and processing–microstructure–property relationships in the welding and joining of titanium aluminides to themselves and to other materials.

  11. Collision tectonics

    Energy Technology Data Exchange (ETDEWEB)

    Coward, M.P.; Ries, A.C.

    1985-01-01

    The motions of lithospheric plates have produced most existing mountain ranges, but structures produced as a result of, and following the collision of continental plates need to be distinguished from those produced before by subduction. If subduction is normally only stopped when collision occurs, then most geologically ancient fold belts must be collisional, so it is essential to recognize and understand the effects of the collision process. This book consists of papers that review collision tectonics, covering tectonics, structure, geochemistry, paleomagnetism, metamorphism, and magmatism.

  12. Analisis Penyerapan Energi Crash Box Pola Origami pada Pengujian Frontal Impact Posisi Angular Frontal

    Directory of Open Access Journals (Sweden)

    Redi Bintarto

    2017-05-01

    Full Text Available In the car, the body structure is designed in such a way so as to transfer and absorb energy. This serves to minimize the result of this accident related to kinetic energy. This needs a system to absorb the kinetic energy maximally, so as a result of a frontal collision events that can be reduced optimally and kinetic energy can be absorbed by a front body structure. Devices used for absorbing kinetic energy in the car is usually called a crash box, which is located between the main structure and bumper. Crash Box generally tubular thin shaped. It has been a lot of research about the crash box. In this study using crash box origami patterns and using methods taguchi orthogonal array L9 (34. AA7003-T7 aluminum material modeled as bilinear isotropic hardening, the loading method is Frontal Impact Frontal Angular Position with impact angles of 5, 15 and 30 degree by using the finite element software simulation methods. The simulation results showed that the crash box in the lowest possible energy absorption were happened at crash box with 5 degree, with 683 153 Joule energy absorbsion. The highest result was happened to crash box number 5 with the results of 3,140.778 Joule. Lowest absorption on impact of 15 degree and 30 degree were happened to crash box number 1 and number 3 with a value of 245 685 Joule and 174 845 Joule, while the highest absorption at mumber 3 with each value 1,708.521 Joule and 1,750.872 Joule.

  13. Collision Mechanics

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Servis, D.P.; Zhang, Shengming

    1999-01-01

    The first section of the present report describes the procedures that are being programmed at DTU for evaluation of the external collision dynamics. Then follows a detailed description of a comprehensive finite element analysis of one collision scenario for MS Dextra carried out at NTUA. The last...

  14. Joining porous components to solid metal structures

    Science.gov (United States)

    Fortini, A.; Tulisiak, G.

    1972-01-01

    Process for joining porous metal material to solid metal structure without cracking or blockage of porous component is described. Procedures of electron beam welding and electroforming are discussed. Illustration of microstructure resulting from process is included.

  15. Taiwan university joins search for antimatter

    CERN Multimedia

    Chiu, Y

    2002-01-01

    National Cheng Kung University announced yesterday that it will be joining the Alpha Magnetic Spectrometer, an international scientific research project aimed at looking for antimatter in space (1 page).

  16. Why do people join trade unions?

    DEFF Research Database (Denmark)

    Toubøl, Jonas; Jensen, Carsten Strøby

    In this study the reasons for joining a trade union are analyzed statistically using high quality data from Statistics Denmark comprising the entire Danish workforce combined with European Social Survey data from rounds 1-3. These data enables measuring the effect of union density at the workplace...... level on union recruitment, which is not done before. Workplace union density is taken to measure the strength of the workplace’s custom of being union member creating an instrumental incentive to join the union. Self-placement on a political left-right scale measures political attitude taken...... to be a value rational motive. The statistical results indicate that the most important predictor of joining the union is workplace union density and only in a secondary manner does political attitude matter. It is concluded that the normative pressure of one’s colleagues is the dominating reason for joining...

  17. Five Performance Enhancements for Hybrid Hash Join

    National Research Council Canada - National Science Library

    Graefe, Goetz

    1992-01-01

    .... We discuss five performance enhancements for hybrid hash join algorithms, namely data compression, large cluster sizes and multi-level recursion, role reversal of build and probe inputs, histogram...

  18. Simulation of mechanical joining for automotive applications

    OpenAIRE

    Gårdstam, Johannes

    2006-01-01

    Regarding the use of material, modern lightweight car bodies are becoming more and more complex than previous constructions. The materials nowadays are used for a more specific field of application and more high strength steels are used and also other materials like aluminium, stainless steel, reinforced polymers are used more frequent. The joining of these materials often requires new or modified joining processes. The aim with this thesis is concerned with the development of simulation mode...

  19. Frontal assessment battery and frontal atrophy in amyotrophic lateral sclerosis

    OpenAIRE

    Terada, Tatsuhiro; Miyata, Jun; Obi, Tomokazu; Kubota, Manabu; Yoshizumi, Miho; Yamazaki, Kinya; Mizoguchi, Kouichi; Murai, Toshiya

    2017-01-01

    Abstract Objectives To determine the potential utility of the frontal assessment battery (FAB) in assessing cognitive impairments in amyotrophic lateral sclerosis (ALS), we investigated the association between the FAB score and regional gray matter volume, and ascertained whether the regional brain alterations related to cognitive impairments occur in relatively mild stage of ALS. Materials and Methods Twenty?four ALS patients with a Mini?Mental State Examination score of >23, a normal score ...

  20. Trajectory similarity join in spatial networks

    KAUST Repository

    Shang, Shuo

    2017-09-07

    The matching of similar pairs of objects, called similarity join, is fundamental functionality in data management. We consider the case of trajectory similarity join (TS-Join), where the objects are trajectories of vehicles moving in road networks. Thus, given two sets of trajectories and a threshold θ, the TS-Join returns all pairs of trajectories from the two sets with similarity above θ. This join targets applications such as trajectory near-duplicate detection, data cleaning, ridesharing recommendation, and traffic congestion prediction. With these applications in mind, we provide a purposeful definition of similarity. To enable efficient TS-Join processing on large sets of trajectories, we develop search space pruning techniques and take into account the parallel processing capabilities of modern processors. Specifically, we present a two-phase divide-and-conquer algorithm. For each trajectory, the algorithm first finds similar trajectories. Then it merges the results to achieve a final result. The algorithm exploits an upper bound on the spatiotemporal similarity and a heuristic scheduling strategy for search space pruning. The algorithm\\'s per-trajectory searches are independent of each other and can be performed in parallel, and the merging has constant cost. An empirical study with real data offers insight in the performance of the algorithm and demonstrates that is capable of outperforming a well-designed baseline algorithm by an order of magnitude.

  1. Speeding Up Neighbour-Joining Tree Construction

    DEFF Research Database (Denmark)

    Brodal, Gerth Stølting; Fagerberg, Rolf; Mailund, Thomas

    A widely used method for constructing phylogenetic trees is the neighbour-joining method of Saitou and Nei. We develope heuristics for speeding up the neighbour-joining method which generate the same phylogenetic trees as the original method. All heuristics are based on using a quad-tree to guide...... the search for the next pair of nodes to join, but di#er in the information stored in quad-tree nodes, the way the search is performed, and in the way the quad-tree is updated after a join. We empirically evaluate the performance of the heuristics on distance matrices obtained from the Pfam collection...... of alignments, and compare the running time with that of the QuickTree tool, a well-known and widely used implementation of the standard neighbour-joining method. The results show that the presented heuristics can give a significant speed-up over the standard neighbour-joining method, already for medium sized...

  2. The IMM Frontal Face Database

    DEFF Research Database (Denmark)

    Fagertun, Jens; Stegmann, Mikkel Bille

    2005-01-01

    This note describes a data set consisting of 120 annotated monocular images of 12 different frontal human faces. Points of correspondence are placed on each image so the data set can be readily used for building statistical models of shape. Format specifications and terms of use are also given in...... in this note. The data set is available in two versions: i) low resolution, given in the zip-file electronic version, ii) high, given in the publication link....

  3. Historical Evolution of the Frontal Lobe Syndrome

    NARCIS (Netherlands)

    Krudop, W.A.; Pijnenburg, Y.A.L.

    2015-01-01

    The function of the frontal lobes and the related frontal lobe syndrome have not been described in detail until relatively late in history. Slowly, the combination of knowledge from animal models, the detailed examination of symptoms after traumatic frontal lobe injuries, and the rise and fall of

  4. Joining Techniques for Ferritic ODS Alloys

    Energy Technology Data Exchange (ETDEWEB)

    V.G. Krishnardula; V.G. Krishnardula; D.E. Clark; T.C. Totemeier

    2005-06-01

    This report presents results of research on advanced joining techniques for ferritic oxide-dispersion strengthened alloys MA956 and PM2000. The joining techniques studied were resistance pressure welding (also known as pressure forge welding), transient liquid phase bonding, and diffusion bonding. All techniques were shown to produce sound joints in fine-grained, unrecrystallized alloys. Post-bond heat treatment to produce a coarse-grained, recrystallized microstructure resulted in grain growth across the bondline for transient liquid phase and diffusion bonds, giving microstructures essentially identical to that of the parent alloy in the recrystallized condition. The effects of bond orientation, boron interlayer thickness, and bonding parameters are discussed for transient liquid phase and diffusion bonding. The report concludes with a brief discussion of ODS joining techniques and their applicability to GEN IV reactor systems.

  5. Transition piece for joining together tubular pieces

    International Nuclear Information System (INIS)

    Holko, K.H.

    1981-01-01

    A transition piece for joining together tubular pieces formed respectively from a low alloy or carbon steel and a high temperature alloy containing at least 16% chromium includes a plurality of tubular parts welded together and formed from materials of selected composition with a maximum chromium content difference of 5% between adjacent parts when the chromium content of each part is below 10% and a maximum chromium difference of 7% between adjacent parts when the chromium content of either part is above 10%. The transition parts are also graded as to such characteristics as thermal expansion coefficient. The transition parts at opposite ends of the transition joint have chromium percentages similar to the tubular pieces to which they are to be joined. The parts may be joined by fusion and/or friction welding and parts may be formed by fusion weld deposition. (author)

  6. Recrafting the Neighbor-Joining Method

    DEFF Research Database (Denmark)

    Mailund; Brodal, Gerth Stølting; Fagerberg, Rolf

    2006-01-01

    Background: The neighbor-joining method by Saitou and Nei is a widely used method for constructing phylogenetic trees. The formulation of the method gives rise to a canonical Θ(n3) algorithm upon which all existing implementations are based. Methods: In this paper we present techniques for speeding...... up the canonical neighbor-joining method. Our algorithms construct the same phylogenetic trees as the canonical neighbor-joining method. The best-case running time of our algorithms are O(n2) but the worst-case remains O(n3). We empirically evaluate the performance of our algoritms on distance...... matrices obtained from the Pfam collection of alignments. Results: The experiments indicate that the running time of our algorithms evolve as Θ(n2) on the examined instance collection. We also compare the running time with that of the QuickTree tool, a widely used efficient implementation of the canonical...

  7. 46 CFR 56.15-1 - Pipe joining fittings.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Pipe joining fittings. 56.15-1 Section 56.15-1 Shipping... APPURTENANCES Fittings § 56.15-1 Pipe joining fittings. (a) Pipe joining fittings certified in accordance with...-welding, buttwelding, and socket-brazing pipe joining fittings, made in accordance with the applicable...

  8. Recrafting the neighbor-joining method

    Directory of Open Access Journals (Sweden)

    Pedersen Christian NS

    2006-01-01

    Full Text Available Abstract Background The neighbor-joining method by Saitou and Nei is a widely used method for constructing phylogenetic trees. The formulation of the method gives rise to a canonical Θ(n3 algorithm upon which all existing implementations are based. Results In this paper we present techniques for speeding up the canonical neighbor-joining method. Our algorithms construct the same phylogenetic trees as the canonical neighbor-joining method. The best-case running time of our algorithms are O(n2 but the worst-case remains O(n3. We empirically evaluate the performance of our algoritms on distance matrices obtained from the Pfam collection of alignments. The experiments indicate that the running time of our algorithms evolve as Θ(n2 on the examined instance collection. We also compare the running time with that of the QuickTree tool, a widely used efficient implementation of the canonical neighbor-joining method. Conclusion The experiments show that our algorithms also yield a significant speed-up, already for medium sized instances.

  9. Possibilities of joining techniques application at railway lines joining and maintenance

    Directory of Open Access Journals (Sweden)

    I. Samardžić

    2011-10-01

    Full Text Available This paper presents most important techniques which is possible to apply at joining of railway lines as well as maintenance procedure. Beside thermit welding as a older joint process for that job (since 1895. it is mentioned flash welding as a modern joining technique interesting from the point of cost efficiency. In a case of maintance tasks it is necessary to caunt arc welding processes and thermit welding, too. Authors gave some experimental date collected during investigation on railway lines joining techniques application.

  10. Body frontal area in passerine birds

    OpenAIRE

    Hedenström, Anders; Rosén, Mikael

    2003-01-01

    Projected body frontal area is used when estimating the parasite drag of bird flight. We investigated the relationship between projected frontal area and body mass among passerine birds, and compared it with an equation based on waterfowl and raptors, which is used as default procedure in a widespread software package for flight performance calculations. The allometric equation based on waterfowl/raptors underestimates the frontal area compared to the passerine equation presented here. Conseq...

  11. Study on the frame body structure of micro-electric vehicle based on frontal crash safety

    Science.gov (United States)

    Lu, Yaoquan; Zhang, Sanchuan

    2017-08-01

    In order to research the safety of skeleton type body of micro-electric vehicles in the frontal collision, the method of finite element modeling and simulation are used to analyze frame body that is fitted with the energy absorption structure, the simulation results show that On the basis of absorbing the most energy and the least of body acceleration, the absorbent structure parameters can be optimized, the optimized parameters are length 180 mm, wall thickness 3 mm and materials Q460.

  12. Collision Risk and Damage after Collision

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Hansen, Peter Friis; Nielsen, Lars Peter

    1996-01-01

    The paper presents a new and complete procedure for calculation of ship-ship collision rates on specific routes and the hull damage caused by such collisions.The procedure is applied to analysis of collision risks for Ro-Ro pasenger vessels. Given a collision the spatial probability distribution...

  13. Machining, joining and modifications of advanced materials

    CERN Document Server

    Altenbach, Holm

    2016-01-01

    This book presents the latest advances in mechanical and materials engineering applied to the machining, joining and modification of modern engineering materials. The contributions cover the classical fields of casting, forming and injection moulding as representative manufacturing methods, whereas additive manufacturing methods (rapid prototyping and laser sintering) are treated as more innovative and recent technologies that are paving the way for the manufacturing of shapes and features that traditional methods are unable to deliver. The book also explores water jet cutting as an innovative cutting technology that avoids the heat build-up typical of classical mechanical cutting. It introduces readers to laser cutting as an alternative technology for the separation of materials, and to classical bonding and friction stir welding approaches in the context of joining technologies. In many cases, forming and machining technologies require additional post-treatment to achieve the required level of surface quali...

  14. Rhenium Mechanical Properties and Joining Technology

    Science.gov (United States)

    Reed, Brian D.; Biaglow, James A.

    1996-01-01

    Iridium-coated rhenium (Ir/Re) provides thermal margin for high performance and long life radiation cooled rockets. Two issues that have arisen in the development of flight Ir/Re engines are the sparsity of rhenium (Re) mechanical property data (particularly at high temperatures) required for engineering design, and the inability to directly electron beam weld Re chambers to C103 nozzle skirts. To address these issues, a Re mechanical property database is being established and techniques for creating Re/C103 transition joints are being investigated. This paper discusses the tensile testing results of powder metallurgy Re samples at temperatures from 1370 to 2090 C. Also discussed is the evaluation of Re/C103 transition pieces joined by both, explosive and diffusion bonding. Finally, the evaluation of full size Re transition pieces, joined by inertia welding, as well as explosive and diffusion bonding, is detailed.

  15. Laser direct joining of metal and plastic

    International Nuclear Information System (INIS)

    Katayama, Seiji; Kawahito, Yousuke

    2008-01-01

    We have developed an innovative rapid laser direct joining process of metal and plastic lap plates without adhesives or glues. The joints made between a Type 304 stainless steel plate and a polyethylene terephthalate (PET) plastic sheet of 30 mm width possessed tensile shear loads of about 3000 N. Transmission electron microscope photographs of the joint demonstrated that Type 304 and the PET were bonded on the atomic, molecular or nanostructural level through a Cr oxide film

  16. Development of Joining Technology for KO TBM

    International Nuclear Information System (INIS)

    Jung, Yang Il; Park, Jeong Yong; Lee, Jung Suk; Choi, Byoung Kwon; Jeong, Yong Hwan; Hong, Bong Guen

    2009-01-01

    TBM(Test Blanket Module) is introduced to test the feasibility and practicability of the design concepts of tritium breeding high temperature blankets relevant to a future fusion power reactor, especially the next step beyond ITER DEMO. Materials for TBM are categorized into five parts: armor material, structural material, tritium breeding material, neutron multiplier, and coolant material. Table I demonstrates the materials briefly. In Korea, two types of TBM, i.e. He cooled solid breeder (HCSB) and He cooled molten Li Breeder (HCML), are considered. For the fabrication of TBM, the joining technology for Be (as an armor material) and ferritic-martensitic steel (as an structural material) is also developing by the Korea Atomic Energy Research Institute. In this paper, the joining of Be with FMS will be presented. The Be and FMS joined successfully by adopting (i) coating of a compliant layer, and (ii) diffusion barrier. The effect of the interlayer properties will be discussed in view of the diffusion and proper bonding strength

  17. Frontal anatomy and reaction time in Autism

    NARCIS (Netherlands)

    Schmitz, Nicole; Daly, Eileen; Murphy, Declan

    2007-01-01

    Widespread frontal lobe abnormalities, encompassing anatomy and function, are known to be implicated in Autistic Spectrum Disorders (ASD). The correlation between neurobiology and behaviour, however, is poorly understood in ASD. The aim of this study was to investigate frontal lobe anatomy and

  18. Mucocele formation after frontal sinus obliteration

    NARCIS (Netherlands)

    Hansen, F. S.; van der Poel, N. A.; Freling, N. J. M.; Fokkens, W. J.

    2018-01-01

    A possible complication of frontal sinus obliteration with fat is the formation of mucoceles. We studied the prevalence of mucoceles as well as and the need for revision surgery. Retrospective case review of forty consecutive patients undergoing frontal sinus obliteration from September 1995 to

  19. Asymmetric Frontal Brain Activity and Parental Rejection

    NARCIS (Netherlands)

    Huffmeijer, R.; Alink, L.R.A.; Tops, M.; Bakermans-Kranenburg, M.J.; van IJzendoorn, M.H.

    2013-01-01

    Asymmetric frontal brain activity has been widely implicated in reactions to emotional stimuli and is thought to reflect individual differences in approach-withdrawal motivation. Here, we investigate whether asymmetric frontal activity, as a measure of approach-withdrawal motivation, also predicts

  20. Ceramic joining through reactive wetting of alumina with calcium ...

    Indian Academy of Sciences (India)

    brazing (Loeman and Tomsia 1988), glass frit joining. (Walls and Ueki 1992), fusion and friction welding (Fernie. 1997) and microwave joining (Meek and Blake 1986;. Palaith and Silberglitt 1989). Most of the ceramic joining investigations are carried out in non-oxide ceramics such as AlN, Si3N4, SiC etc while ZrO2 and ...

  1. Reliable and economical method to join optical tables

    Science.gov (United States)

    Corzo-Garcia, S. C.; Medina-Lopez, R. J.; Anderson, S.; Castro-Camus, E.; Carriles, R.; Ruiz-Marquez, A.

    2011-11-01

    We present a practical method for joining pneumatically floated optical tables with no manufacturer preparation. We compare the stability of the joined table with one of its parts alone using Michelson Interferometry. We also compare the stability of two different pneumatic leg configurations in order to find the optimal one. We demonstrate that the joined table has comparable rigidity to its segments.

  2. Building Very Large Neighbour-Joining Trees

    DEFF Research Database (Denmark)

    Simonsen, Martin; Mailund, Thomas; Pedersen, Christian Nørgaard Storm

    2010-01-01

    The neighbour-joining method by Saitou and Nei is a widely used method for phylogenetic reconstruction, made popular by a combination of computational efficiency and reasonable accuracy. With its cubic running time by Studier and Kepler, the method scales to hundreds of species, and while......, and the NJ method in general, becomes a problem when inferring phylogenies with 10000+ taxa. In this paper we present two extentions of RapidNJ which reduce memory requirements and enable RapidNJ to infer very large phylogenetic trees efficiently. We also present an improved search heuristic for Rapid...

  3. Joining by plating: optimization of occluded angle

    International Nuclear Information System (INIS)

    Dini, J.W.; Johnson, H.R.; Kan, Y.R.

    1978-11-01

    An empirical method has been developed for predicting the minimum angle required for maximum joint strength for materials joined by plating. This is done through a proposed power law failure function, whose coefficients are taken from ring shear and conical head tensile data for plating/substrate combinations and whose exponent is determined from one set of plated-joint data. Experimental results are presented for Al-Ni-Al (7075-T6) and AM363-Ni-AM363 joints, and the failure function is used to predict joint strengths for Al-Ni-Al (2024-T6), UTi-Ni-UTi, and Be-Ti-Be

  4. Thin shells joining local cosmic string geometries

    Energy Technology Data Exchange (ETDEWEB)

    Eiroa, Ernesto F. [Universidad de Buenos Aires, Ciudad Universitaria Pabellon I, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Buenos Aires (Argentina); Instituto de Astronomia y Fisica del Espacio (IAFE, CONICET-UBA), Buenos Aires (Argentina); Rubin de Celis, Emilio; Simeone, Claudio [Universidad de Buenos Aires, Ciudad Universitaria Pabellon I, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Buenos Aires (Argentina); Ciudad Universitaria Pabellon I, IFIBA-CONICET, Buenos Aires (Argentina)

    2016-10-15

    In this article we present a theoretical construction of spacetimes with a thin shell that joins two different local cosmic string geometries. We study two types of global manifolds, one representing spacetimes with a thin shell surrounding a cosmic string or an empty region with Minkowski metric, and the other corresponding to wormholes which are not symmetric across the throat located at the shell. We analyze the stability of the static configurations under perturbations preserving the cylindrical symmetry. For both types of geometries we find that the static configurations can be stable for suitable values of the parameters. (orig.)

  5. Large-Scale Similarity Joins With Guarantees

    DEFF Research Database (Denmark)

    Pagh, Rasmus

    2015-01-01

    The ability to handle noisy or imprecise data is becoming increasingly important in computing. In the database community the notion of similarity join has been studied extensively, yet existing solutions have offered weak performance guarantees. Either they are based on deterministic filtering...... techniques that often, but not always, succeed in reducing computational costs, or they are based on randomized techniques that have improved guarantees on computational cost but come with a probability of not returning the correct result. The aim of this paper is to give an overview of randomized techniques...

  6. The usages of JOIN2 authority records

    CERN Multimedia

    CERN. Geneva; Thiele, Robert

    2017-01-01

    An important base of the common JOIN2 repository infrastructure of DESY, DKFZ, FZJ, GSI, MLZ and RWTH Aachen are about 134 000 authority records for grants, projects, large-scale infrastructures, cooperations, journals, and different kinds of keys. All instances are using the authorities together. We will present how these authority data are used for different purposes e.g. the recent and upcoming obligations to report to regard to our funding and the data export to openAire. Furthermore, we discuss this in dependence to the German “Kerndatensatz Forschung”, which will be the new standard for future.

  7. Mapping the Join Calculus to Heterogeneous Hardware

    Directory of Open Access Journals (Sweden)

    Peter Calvert

    2013-02-01

    Full Text Available As modern architectures introduce additional heterogeneity and parallelism, we look for ways to deal with this that do not involve specialising software to every platform. In this paper, we take the Join Calculus, an elegant model for concurrent computation, and show how it can be mapped to an architecture by a Cartesian-product-style construction, thereby making use of the calculus' inherent non-determinism to encode placement choices. This unifies the concepts of placement and scheduling into a single task.

  8. Evaluating the Upset Protrusion Joining (UPJ) Method to Join magnesium Castings to Dissimilar Metals

    Energy Technology Data Exchange (ETDEWEB)

    Logan, Stephen D. [FCA US LLC

    2015-08-19

    This presentation discusses advantages and best practices for incorporating magnesium in automotive component applications to achieve substantial mass reduction, as well as some of the key challenges with respect to joining, coating, and galvanic corrosion, before providing an introduction and status update of the U.S. Department of Energy and Department of Defense jointly sponsored Upset Protrusion Joining (UPJ) process development and evaluation project. This update includes sharing performance results of a benchmark evaluation of the self-pierce riveting (SPR) process for joining dissimilar magnesium (Mg) to aluminum (Al) materials in four unique coating configurations before introducing the UPJ concept and comparing performance results of the joints made with the UPJ process to those made with the SPR process.

  9. Chronic frontal sinusitis presenting with complications

    Directory of Open Access Journals (Sweden)

    Zainab Sunu Ali

    2013-01-01

    Full Text Available A frontocutaneous fistula secondary to chronic frontal sinusitis can present with a fistulous opening in the forehead or in the eyelid. It may or may not be associated with Pott′s puffy tumor. In this article, we present 2 cases. A case of frontocutaenous fistula with opening in the upper eyelid at the lateral portion of floor of frontal sinus and another case of chronic frontal sinusitis with sub-periosteal abscess in the forehead on the right side near the eyebrow. Relevant literature has also been reviewed.

  10. Muscle activity influence on the kinematics of the cervical spine in frontal tests.

    Science.gov (United States)

    Dehner, Christoph; Schick, Sylvia; Kraus, Michael; Scola, Alexander; Hell, Wolfram; Kramer, Michael

    2013-01-01

    The question of muscle activity influence on the cervical spine kinematics during rear-end and frontal crash events has been discussed. Less data are available concerning frontal collisions. Therefore, the objective of this study was to investigate the influence of the ventral and dorsal neck muscles on the cervical spine kinematics during simulated frontal sled collisions. A frontal collision with a velocity change (delta V) of 10.2 km/h was simulated in a sled test with 10 healthy subjects (7 female; 3 male). A high-speed camera and accelerometers recorded the motion and acceleration data. The activity of the sternocleidomastoid muscles was recorded with surface electrodes. To avoid cross-talk, an intramuscular recording of the semispinalis capitis muscles was performed with fine-wire electrodes. The sequence of both muscle activities was reproducible in all subjects. The maximal force of the sternocleidomastoid muscle was observed after a median of 152 ms, with 0 defining the time of the trigger signal. With earlier onset of muscle force, maximal dorsal horizontal acceleration of the head (r = -0.600) was reached later and the ventral translation (r = -0.733) and flexion movement (r = -0.755) set in earlier. The maximal force of the semispinalis capitis muscle was observed after a median of 160 ms. If the duration of muscle force was longer, the maximal head flexion (r = 0.685) and the maximal ventral head translation (r = 0.738) were reached later. The sternocleidomastoid muscle force is mainly associated with the horizontal head acceleration and influences the onset of the flexion and translation motion. To summarize, these temporal correlations allow the conclusion that the semispinalis capitis muscle force is mainly associated with the angular head acceleration and influences the duration of the flexion and translation motion.

  11. Puck collisions

    Science.gov (United States)

    Hauge, E. H.

    2012-09-01

    Collisions between two ice hockey pucks sliding on frictionless ice are studied, with both inelasticity and frictional contact between the colliding surfaces of the two pucks taken into account. The latter couples translational and rotational motion. The full solution depends on the sign and magnitude of the initial mismatch between the surface velocities at the point of contact. The initial state defines two physically distinct regimes for the friction coefficient. To illustrate the complexities, we discuss at length the typical situation (well known from curling) when puck number 1 is initially at rest, and is hit by puck number 2 with an arbitrary impact parameter, velocity and angular velocity. We find that the total outgoing angle between the pucks exceeds \\frac{1}{2}\\pi if and only if the collision leads to a net increase in the translational part of the kinetic energy. The conditions for this to happen are scrutinized, and the results are presented both analytically and numerically by a set of representative curves. This paper is written with an ambitious undergraduate, and her teacher, in mind.

  12. Joining of Tungsten Armor Using Functional Gradients

    International Nuclear Information System (INIS)

    John Scott O'Dell

    2006-01-01

    The joining of low thermal expansion armor materials such as tungsten to high thermal expansion heat sink materials has been a major problem in plasma facing component (PFC) development. Conventional planar bonding techniques have been unable to withstand the high thermal induced stresses resulting from fabrication and high heat flux testing. During this investigation, innovative functional gradient joints produced using vacuum plasma spray forming techniques have been developed for joining tungsten armor to copper alloy heat sinks. A model was developed to select the optimum gradient architecture. Based on the modeling effort, a 2mm copper rich gradient was selected. Vacuum plasma pray parameters and procedures were then developed to produce the functional gradient joint. Using these techniques, dual cooling channel, medium scale mockups (32mm wide x 400mm length) were produced with vacuum plasma spray formed tungsten armor. The thickness of the tungsten armor was up to 5mm thick. No evidence of debonding at the interface between the heat sink and the vacuum plasma sprayed material was observed.

  13. Joining of Tungsten Armor Using Functional Gradients

    Energy Technology Data Exchange (ETDEWEB)

    John Scott O' Dell

    2006-12-31

    The joining of low thermal expansion armor materials such as tungsten to high thermal expansion heat sink materials has been a major problem in plasma facing component (PFC) development. Conventional planar bonding techniques have been unable to withstand the high thermal induced stresses resulting from fabrication and high heat flux testing. During this investigation, innovative functional gradient joints produced using vacuum plasma spray forming techniques have been developed for joining tungsten armor to copper alloy heat sinks. A model was developed to select the optimum gradient architecture. Based on the modeling effort, a 2mm copper rich gradient was selected. Vacuum plasma pray parameters and procedures were then developed to produce the functional gradient joint. Using these techniques, dual cooling channel, medium scale mockups (32mm wide x 400mm length) were produced with vacuum plasma spray formed tungsten armor. The thickness of the tungsten armor was up to 5mm thick. No evidence of debonding at the interface between the heat sink and the vacuum plasma sprayed material was observed.

  14. People's Republic of China joins ITER

    International Nuclear Information System (INIS)

    Huo Yuping

    2003-01-01

    The People's Republic of China is the largest developing country with a projected population of 1.6 - 2 billion people and an energy consumption growing from the current 1.3 Billion Tons Coal Equivalent (TCE) to more than 4 Billion TCE by 2050. This large demand needs to be accommodated in a sustainable way, requiring energy generation in an environmentally friendly way. Fusion is one of the most promising candidates to solve this important issue. This explains why in the second half of 2002, the ITER Participants' delegations to the ITER Negotiations received expression of interest from the People's Republic of China in the possibility of Chinese participation in ITER, including joining the ongoing Negotiations. The speed with which the Chinese authorities had made their decision to participate in the ITER Negotiations was impressive. The Prime Minister and the State Council had already confirmed their decision to apply to join ITER as soon as possible, and Mr. Xu Guanhua, Chinese Minister of Science and Technology, wrote on behalf of his government, on 10 January 2003, to the four heads of delegation in the ITER Negotiations, requesting that China participate in the present ITER Negotiations, pointing out that China intends to provide a substantial contribution to the Project, comparable to what is currently envisaged by some of the participants in the present Negotiations

  15. Teens join the MoEDAL collaboration

    CERN Multimedia

    Stephanie Hills

    2013-01-01

    The principal investigator for any institute joining an experimental collaboration is generally a self-assured researcher with evident leadership skills and an in-depth knowledge of their subject gained over many years. Katherine Evans fits the brief in every respect, except that she is 17 years old and her research institute is the Langton Star Centre, based at the Simon Langton Grammar School for Boys. The school has just joined the MoEDAL experiment.   Teacher Becky Parker (left) with two students from the Simon Langton Grammar School for Boys in the MoEDAL experimental area. MoEDAL, the latest LHC experiment has detectors located close to the interaction point of the LHCb experiment. This new experiment is designed to search for the highly ionizing avatars of new physics at the LHC, specifically the magnetic monopole or dyon and other highly ionizing stable massive particles from a number of beyond-the-Standard-Model scenarios. MoEDAL was approved in 2010 and is due to start taking data i...

  16. Joining Dental Ceramic Layers With Glass

    Science.gov (United States)

    Saied, MA; Lloyd, IK; Haller, WK; Lawn, BR

    2011-01-01

    Objective Test the hypothesis that glass-bonding of free-form veneer and core ceramic layers can produce robust interfaces, chemically durable and aesthetic in appearance and, above all, resistant to delamination. Methods Layers of independently produced porcelains (NobelRondo™ Press porcelain, Nobel BioCare AB and Sagkura Interaction porcelain, Elephant Dental) and matching alumina or zirconia core ceramics (Procera alumina, Nobel BioCare AB, BioZyram yttria stabilized tetragonal zirconia polycrystal, Cyrtina Dental) were joined with designed glasses, tailored to match thermal expansion coefficients of the components and free of toxic elements. Scanning electron microprobe analysis was used to characterize the chemistry of the joined interfaces, specifically to confirm interdiffusion of ions. Vickers indentations were used to drive controlled corner cracks into the glass interlayers to evaluate the toughness of the interfaces. Results The glass-bonded interfaces were found to have robust integrity relative to interfaces fused without glass, or those fused with a resin-based adhesive. Significance The structural integrity of the interfaces between porcelain veneers and alumina or zirconia cores is a critical factor in the longevity of all-ceramic dental crowns and fixed dental prostheses. PMID:21802131

  17. Spatio-Temporal Joins on Symbolic Indoor Tracking Data

    DEFF Research Database (Denmark)

    Lu, Hua; Yang, Bin; Jensen, Christian S.

    2011-01-01

    and studies probabilistic, spatio-temporal joins on historical indoor tracking data. Two meaningful types of join are defined. They return object pairs that satisfy spatial join predicates either at a time point or during a time interval. The predicates considered include “same X,” where X is a semantic...... region such as a room or hallway. Based on an analysis on the uncertainty inherent to indoor tracking data, effective join probabilities are formalized and evaluated for object pairs. Efficient two-phase hash-based algorithms are proposed for the point and interval joins. In a filter-and-refine framework...

  18. Cranialization of the frontal sinus for secondary mucocele prevention following open surgery for benign frontal lesions.

    Directory of Open Access Journals (Sweden)

    Gilad Horowitz

    Full Text Available OBJECTIVE: To compare frontal sinus cranialization to obliteration for future prevention of secondary mucocele formation following open surgery for benign lesions of the frontal sinus. STUDY DESIGN: Retrospective case series. SETTING: Tertiary academic medical center. PATIENTS: Sixty-nine patients operated for benign frontal sinus pathology between 1994 and 2011. INTERVENTIONS: Open excision of benign frontal sinus pathology followed by either frontal obliteration (n = 41, 59% or frontal cranialization (n = 28, 41%. MAIN OUTCOME MEASURES: The prevalence of post-surgical complications and secondary mucocele formation were compiled. RESULTS: Pathologies included osteoma (n = 34, 49%, mucocele (n = 27, 39%, fibrous dysplasia (n = 6, 9%, and encephalocele (n = 2, 3%. Complications included skin infections (n = 6, postoperative cutaneous fistula (n = 1, telecanthus (n = 4, diplopia (n = 3, nasal deformity (n = 2 and epiphora (n = 1. None of the patients suffered from postoperative CSF leak, meningitis or pneumocephalus. Six patients, all of whom had previously undergone frontal sinus obliteration, required revision surgery due to secondary mucocele formation. Statistical analysis using non-inferiority test reveal that cranialization of the frontal sinus is non-inferior to obliteration for preventing secondary mucocele formation (P<0.0001. CONCLUSION: Cranialization of the frontal sinus appears to be a good option for prevention of secondary mucocele development after open excision of benign frontal sinus lesions.

  19. synthesis of microporous polymers by frontal polymerization

    Indian Academy of Sciences (India)

    Unknown

    EGDM) copolymers of varying compositions were synthesized by free-radically triggered thermal frontal polymerization (FP) as well as by suspension polymerization (SP) using azobisisobutyronitrile [AIBN] as initiator. The two sets of copolymers.

  20. Human Frontal Lobes and AI Planning Systems

    Science.gov (United States)

    Levinson, Richard; Lum, Henry Jr. (Technical Monitor)

    1994-01-01

    Human frontal lobes are essential for maintaining a self-regulating balance between predictive and reactive behavior. This paper describes a system that integrates prediction and reaction based on neuropsychological theories of frontal lobe function. In addition to enhancing our understanding of deliberate action in humans' the model is being used to develop and evaluate the same properties in machines. First, the paper presents some background neuropsychology in order to set a general context. The role of frontal lobes is then presented by summarizing three theories which formed the basis for this work. The components of an artificial frontal lobe are then discussed from both neuropsychological and AI perspectives. The paper concludes by discussing issues and methods for evaluating systems that integrate planning and reaction.

  1. Frontal lobe alterations in schizophrenia: a review.

    Science.gov (United States)

    Mubarik, Ateeq; Tohid, Hassaan

    2016-01-01

    To highlight the changes in the frontal lobe of the human brain in people with schizophrenia. This was a qualitative review of the literature. Many schizophrenic patients exhibit functional, structural, and metabolic abnormalities in the frontal lobe. Some patients have few or no alterations, while some have more functional and structural changes than others. Magnetic resonance imaging (MRI) shows structural and functional changes in volume, gray matter, white matter, and functional activity in the frontal lobe, but the mechanisms underlying these changes are not yet fully understood. When schizophrenia is studied as an essential topic in the field of neuropsychiatry, neuroscientists find that the frontal lobe is the most commonly involved area of the human brain. A clear picture of how this lobe is affected in schizophrenia is still lacking. We therefore recommend that further research be conducted to improve understanding of the pathophysiology of this psychiatric dilemma.

  2. Corpus callosum lipoma with frontal encephalocele

    International Nuclear Information System (INIS)

    Srinivasa Rao, A.; Rao, V.R.K.; Ravi Mandalam, K.; Gupta, A.K.; Kumar, S.; Joseph, S.; Unni, M.

    1990-01-01

    Computed tomographic and plain X-ray observations in a patient with corpus callosum lipoma associated with frontal encephalocele are reported. The rarity of the lesion and the specific diagnostic criteria on CT are emphasised. (orig.)

  3. New Perspectives on Southern Ocean Frontal Variability

    Science.gov (United States)

    Chapman, Christopher

    2017-04-01

    The frontal structure of the Southern Ocean is investigated using a the Wavelet/Higher Order Statistics Enhancement (WHOSE) frontal detection method, introduced in Chapman (2014). This methodology is applied to 21 years of daily gridded sea-surface height (SSH) data to obtain daily maps of the locations of the fronts. By forming frontal occurrence frequency maps and then approximating these occurrence-maps by a superposition of simple functions, the time-mean locations of the fronts, as well as a measure of their capacity to meander, are obtained and related to the frontal locations found by previous studies. The spatial and temporal variability of the frontal structure is then considered. The number of fronts is found to be highly variable throughout the Southern Ocean, increasing (`splitting') downstream of large bathymetric features and decreasing (`merging') in regions where the fronts are tightly controlled by the underlying topography. In contrast, frontal meandering remains relatively constant. Contrary to many previous studies, little no southward migration of the fronts over the 1993-2014 time period is found, and there is only weak sensitivity to atmospheric forcing related to SAM or ENSO. Finally, the implications of splitting and merging for the flux of tracers will be discussed.

  4. Collision avoidance

    Energy Technology Data Exchange (ETDEWEB)

    Glynn, P.

    2008-04-01

    A suite of new collision avoidance systems (CAS 1,2,3, and 4) for heavy vehicles particularly mine haul trucks, is presented for vehicles whose structure and size necessarily impeded driver visibility. The systems use probe radar systems, continuous wave Doppler radar, ultrasonic Doppler, radio frequency tagging and laser scanning technology. The main goal of the ACARP/CSIRO funded projects is to determine the appropriate use and adaptation of commercially available technologies, and where possible, produce a low cost variant suitable for use in proximity detection on large mining industry haul trucks. CAS variants produced were subjected to a field demonstration and linked to the output from the earlier CAS 1 project. The research concentrated on large mine haul trucks operating in open cut coal mines. While the results are especially applicable to the Queensland and New South Wales coal industries, they are also applicable worldwide. 1 tab.

  5. Mind the movement: Frontal asymmetry stands for behavioral motivation, bilateral frontal activation for behavior.

    Science.gov (United States)

    Rodrigues, Johannes; Müller, Mathias; Mühlberger, Andreas; Hewig, Johannes

    2018-01-01

    Frontal asymmetry has been investigated over the past 30 years, and several theories have been developed about its meaning. The original theory of Davidson and its diversification by Harmon-Jones & Allen allocated approach motivation to relative left frontal brain activity and withdrawal motivation to relative right frontal brain activity. Hewig and colleagues extended this theory by adding bilateral frontal activation representing a biological correlate of the behavioral activation system if actual behavior is shown. Wacker and colleagues formulated a theory related to the revised reinforcement sensitivity theory by Gray & McNaughton. Here, relative left frontal brain activation represents the revised behavioral activation system and behavior, while relative right frontal brain activation represents the revised behavioral inhibition system, representing the experience of conflict. These theories were investigated with a newly developed paradigm where participants were able to move around freely in a virtual T maze via joystick while having their EEG recorded. Analyzing the influence of frontal brain activation during this virtual reality task on observable behavior for 30 participants, we found more relative left frontal brain activation during approach behavior and more relative right brain activation for withdrawal behavior of any kind. Additionally, there was more bilateral frontal brain activation when participants were engaged in behavior compared to doing nothing. Hence, this study provides evidence for the idea that frontal asymmetry stands for behavioral approach or avoidance motivation, and bilateral frontal activation stands for behavior. Additionally, observable behavior is not only determined by frontal asymmetry, but also by relevant traits. © 2017 Society for Psychophysiological Research.

  6. G. N. Rassam Joins AGU Staff

    Science.gov (United States)

    Ghassan N. Rassam joined the AGU staff today, assuming the dual roles of Division Director for Public Information and Marketing and of Special Assistant for Nonprint Publications. He comes to AGU from the American Geological Institute, where he has been chief editor and assistant director of the GeoRef Information System.As Director of Public Information and Marketing, Rassam will head one of AGU's five divisions. He will have under his purview the Public Information Department and the Promotion and Sales Department. The Public Information Department produces Eos and also has the responsibility for press relations, including the preparation of news releases and the operation of press rooms at meetings. These activities are critical to the implementation of AGU's public education and public affairs initiatives, as well as to the central role of AGU in promoting the unity of geophysics.

  7. Automated MRI parcellation of the frontal lobe.

    Science.gov (United States)

    Ranta, Marin E; Chen, Min; Crocetti, Deana; Prince, Jerry L; Subramaniam, Krish; Fischl, Bruce; Kaufmann, Walter E; Mostofsky, Stewart H

    2014-05-01

    Examination of associations between specific disorders and physical properties of functionally relevant frontal lobe sub-regions is a fundamental goal in neuropsychiatry. Here, we present and evaluate automated methods of frontal lobe parcellation with the programs FreeSurfer(FS) and TOADS-CRUISE(T-C), based on the manual method described in Ranta et al. [2009]: Psychiatry Res 172:147-154 in which sulcal-gyral landmarks were used to manually delimit functionally relevant regions within the frontal lobe: i.e., primary motor cortex, anterior cingulate, deep white matter, premotor cortex regions (supplementary motor complex, frontal eye field, and lateral premotor cortex) and prefrontal cortex (PFC) regions (medial PFC, dorsolateral PFC, inferior PFC, lateral orbitofrontal cortex [OFC] and medial OFC). Dice's coefficient, a measure of overlap, and percent volume difference were used to measure the reliability between manual and automated delineations for each frontal lobe region. For FS, mean Dice's coefficient for all regions was 0.75 and percent volume difference was 21.2%. For T-C the mean Dice's coefficient was 0.77 and the mean percent volume difference for all regions was 20.2%. These results, along with a high degree of agreement between the two automated methods (mean Dice's coefficient = 0.81, percent volume difference = 12.4%) and a proof-of-principle group difference analysis that highlights the consistency and sensitivity of the automated methods, indicate that the automated methods are valid techniques for parcellation of the frontal lobe into functionally relevant sub-regions. Thus, the methodology has the potential to increase efficiency, statistical power and reproducibility for population analyses of neuropsychiatric disorders with hypothesized frontal lobe contributions. Copyright © 2013 Wiley Periodicals, Inc.

  8. [Normal aging of frontal lobe functions].

    Science.gov (United States)

    Calso, Cristina; Besnard, Jérémy; Allain, Philippe

    2016-03-01

    Normal aging in individuals is often associated with morphological, metabolic and cognitive changes, which particularly concern the cerebral frontal regions. Starting from the "frontal lobe hypothesis of cognitive aging" (West, 1996), the present review is based on the neuroanatomical model developed by Stuss (2008), introducing four categories of frontal lobe functions: executive control, behavioural and emotional self-regulation and decision-making, energization and meta-cognitive functions. The selected studies only address the changes of one at least of these functions. The results suggest a deterioration of several cognitive frontal abilities in normal aging: flexibility, inhibition, planning, verbal fluency, implicit decision-making, second-order and affective theory of mind. Normal aging seems also to be characterised by a general reduction in processing speed observed during neuropsychological assessment (Salthouse, 1996). Nevertheless many cognitive functions remain preserved such as automatic or non-conscious inhibition, specific capacities of flexibility and first-order theory of mind. Therefore normal aging doesn't seem to be associated with a global cognitive decline but rather with a selective change in some frontal systems, conclusion which should be taken into account for designing caring programs in normal aging.

  9. Frontal cephalometrics: practical applications, part 2.

    Science.gov (United States)

    Grummons, Duane; Ricketts, Robert M

    2004-01-01

    To (1) demonstrate the needs and benefits of three-dimensional diagnostic and treatment applications; (2) illustrate practical clinical applications of anteroposterior images and frontal analysis; and (3) enhance utilization of the Ricketts and Grummons frontal analyses. Frontal analysis methods and applications are specified and integrated into facial, smile, jaw, and occlusal therapies. Asymmetry conditions must be differentially diagnosed and effectively treated. Frontal and related image analysis and tracing steps are detailed. Asymmetry of facial parts is the rule, rather than the exception. Dental and facial midlines, occlusal plane, chin location, and smile esthetics are primarily emphasized. Beautiful facial proportions and smile harmony can be developed despite initial facial dysmorphosis and disproportions. Patients view themselves from the frontal perspective, so this carries priority when assessing problems. It is important to know the etiology of asymmetry to assist others with genetic counseling. Facial harmony and smile beauty are optimal when facial and maxillary dental midlines are aligned. The maxillary dentition width should be sufficiently wide to be in harmony with the individual patient facial morphology. The occlusal plane should be level and the chin centered as much as possible. Best facial development and proportionality exist when the skeletal and dental components are optimized transversely and are symmetric.

  10. Tratamiento y complicaciones de las fracturas de seno frontal Frontal sinus fracture treatment and complications

    Directory of Open Access Journals (Sweden)

    S. Heredero Jung

    2007-06-01

    Full Text Available Introducción. Las fracturas de seno frontal se producen como resultado de impactos de alta energía. Un tratamiento inadecuado puede conducir a complicaciones serias incluso muchos años después del traumatismo. Objetivos. Evaluar los datos epidemiológicos y revisar las complicaciones asociadas. Estandarizar el protocolo de tratamiento. Materiales y métodos. Se revisaron 95 pacientes diagnosticados de fracturas de seno frontal pertenecientes al servicio de Cirugía Oral y Maxilofacial del Hospital Universitario 12 de Octubre de Madrid, entre enero de 1990 y diciembre de 2004. Resultados. La edad media de los pacientes revisados es de 34 años. La mayoría son hombres (78% y la causa más frecuente del traumatismo, los accidentes de tráfico. El patrón de fractura más común es el que afecta únicamente a la pared anterior del seno frontal. Las complicaciones descritas son: deformidad estética frontal, sinusitis frontal, mucocele frontal, celulitis fronto-orbitaria, intolerancia al material de osteosíntesis, complicaciones infecciosas del SNC y persistencia de fístula de líquido cefalorraquídeo. Conclusiones. El objetivo ha de estar encaminado a prevenir las complicaciones asociadas a los pacientes con fracturas de seno frontal. Hay que individualizar el protocolo de tratamiento en cada caso. Es recomendable un seguimiento a largo plazo para identificar precozmente las posibles complicaciones.Introduction. Frontal sinus fractures are caused by high velocity impacts. Inappropriate treatment can lead to serious complications, even many years after the trauma. Objectives. To evaluate epidemiological data and associated complications. To standardize the treatment protocol. Materials and methods. the clinical records of 95 patients with frontal sinus fractures treated between January 1990 and December 2004 at the Oral and Maxillofacial Surgery Department, "12 de Octubre" Hospital (Madrid, Spain, were reviewed. Results. The average age of

  11. Evaluating the Upset Protrusion Joining (UPJ) Method to Join Magnesium Castings to Dissimilar Metals

    Energy Technology Data Exchange (ETDEWEB)

    Logan, Stephen [FCA US LLC, Auburn Hills, MI (United States)

    2016-02-24

    This presentation discusses advantages and best practices for incorporating magnesium in automotive component applications to achieve substantial mass reduction, as well as some of the key challenges with respect to joining, coating, and galvanic corrosion, before providing an introduction and status update of the U.S. Department of Energy and Department of Defense jointly sponsored Upset Protrusion Joining (UPJ) process development and evaluation project. This update includes sharing performance results of a benchmark evaluation of the self-pierce riveting (SPR) process for joining dissimilar magnesium (Mg) to aluminum (Al) materials in four unique coating configurations before introducing the UPJ concept and comparing performance results of the joints made with the UPJ process to those made with the SPR process. Key results presented include: The benchmark SPR process can produce good joints in the MgAM60B-Al 6013 joint configuration with minimal cracking in the Mg coupons if the rivet is inserted from the Mg side into the Al side; Numerous bare Mg to bare Al joints made with the SPR process separated after only 6-wks of accelerated corrosion testing due to fracture of the rivet as a result of hydrogen embrittlement; For the same joint configurations, UPJ demonstrated substantially higher pre-corrosion joint strengths and post-corrosion joint strengths, primarily because of the larger diameter protrusion compared to smaller SPR rivet diameter and reduced degradation due to accelerated corrosion exposure; As with the SPR process, numerous bare Mg to bare Al joints made with the UPJ process also separated after 6-wks of accelerated corrosion testing, but unlike the SPR experience, the UPJ joints experienced degradation of the boss and head because of galvanic corrosion of the Mg casting, not hydrogen embrittlement of the steel rivet; In the configuration where both the Mg and Al were pretreated with Alodine 5200 prior to joining and the complete assembly was powder

  12. CERN clubs join the fiftieth anniversary party!

    CERN Multimedia

    2004-01-01

    CERN's clubs are planning to celebrate the Organization's 50th anniversary by organising a variety of special events. It's raining projects! CERN's clubs have chosen to celebrate the Organization's Golden Jubilee, each in its own style, by organising a whole host of anniversary events. While the Cine-Club continues to screen films made in the Member States on Thursday evenings, other clubs are organising special races and tournaments to honour CERN's 50th year. The CERN Rugby Club led the way in early April when it hosted a children's tournament which brought the Laboratory firmly into the view of its many young participants. On 24 April, the Cycling Club moves to centre stage as it takes its members on a unique 50-km discovery trip around the countryside above the tunnel of the future LHC. The Croquet Club, the Running Club, the Horse Riding Club and the Golf Club will all be joining the party in May and June. After that, football, softball, cycling, pétanque and sailing are just some of the items on a sp...

  13. Cephalic aura after frontal lobe resection.

    Science.gov (United States)

    Kakisaka, Yosuke; Jehi, Lara; Alkawadri, Rafeed; Wang, Zhong I; Enatsu, Rei; Mosher, John C; Dubarry, Anne-Sophie; Alexopoulos, Andreas V; Burgess, Richard C

    2014-08-01

    A cephalic aura is a common sensory aura typically seen in frontal lobe epilepsy. The generation mechanism of cephalic aura is not fully understood. It is hypothesized that to generate a cephalic aura extensive cortical areas need to be excited. We report a patient who started to have cephalic aura after right frontal lobe resection. Magnetoencephalography (MEG) showed interictal spike and ictal change during cephalic aura, both of which were distributed in the right frontal region, and the latter involved much more widespread areas than the former on MEG sensors. The peculiar seizure onset pattern may indicate that surgical modification of the epileptic network was related to the appearance of cephalic aura. We hypothesize that generation of cephalic aura may be associated with more extensive cortical involvement of epileptic activity than that of interictal activity, in at least a subset of cases. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. The frontal method in hydrodynamics simulations

    Science.gov (United States)

    Walters, R.A.

    1980-01-01

    The frontal solution method has proven to be an effective means of solving the matrix equations resulting from the application of the finite element method to a variety of problems. In this study, several versions of the frontal method were compared in efficiency for several hydrodynamics problems. Three basic modifications were shown to be of value: 1. Elimination of equations with boundary conditions beforehand, 2. Modification of the pivoting procedures to allow dynamic management of the equation size, and 3. Storage of the eliminated equations in a vector. These modifications are sufficiently general to be applied to other classes of problems. ?? 1980.

  15. QuickJoin—Fast Neighbour-Joining Tree Reconstruction

    DEFF Research Database (Denmark)

    Mailund; Pedersen, Christian N. Storm

    2004-01-01

    We have built a tool for fast construction of very large phylogenetic trees. The tool uses heuristics for speeding up the neighbour-joining algorithm—while still constructing the same tree as the original neighbour-joining algorithm—making it possible to construct trees for ~8000 species in less...

  16. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the procedure...

  17. Brazil to Join the European Southern Observatory

    Science.gov (United States)

    2010-12-01

    The Federative Republic of Brazil has yesterday signed the formal accession agreement paving the way for it to become a Member State of the European Southern Observatory (ESO). Following government ratification Brazil will become the fifteenth Member State and the first from outside Europe. On 29 December 2010, at a ceremony in Brasilia, the Brazilian Minister of Science and Technology, Sergio Machado Rezende and the ESO Director General, Tim de Zeeuw signed the formal accession agreement aiming to make Brazil a Member State of the European Southern Observatory. Brazil will become the fifteen Member State and the first from outside Europe. Since the agreement means accession to an international convention, the agreement must now be submitted to the Brazilian Parliament for ratification [1]. The signing of the agreement followed the unanimous approval by the ESO Council during an extraordinary meeting on 21 December 2010. "Joining ESO will give new impetus to the development of science, technology and innovation in Brazil as part of the considerable efforts our government is making to keep the country advancing in these strategic areas," says Rezende. The European Southern Observatory has a long history of successful involvement with South America, ever since Chile was selected as the best site for its observatories in 1963. Until now, however, no non-European country has joined ESO as a Member State. "The membership of Brazil will give the vibrant Brazilian astronomical community full access to the most productive observatory in the world and open up opportunities for Brazilian high-tech industry to contribute to the European Extremely Large Telescope project. It will also bring new resources and skills to the organisation at the right time for them to make a major contribution to this exciting project," adds ESO Director General, Tim de Zeeuw. The European Extremely Large Telescope (E-ELT) telescope design phase was recently completed and a major review was

  18. Performance on the Frontal Assessment Battery is sensitive to frontal lobe damage in stroke patients.

    Science.gov (United States)

    Kopp, Bruno; Rösser, Nina; Tabeling, Sandra; Stürenburg, Hans Jörg; de Haan, Bianca; Karnath, Hans-Otto; Wessel, Karl

    2013-11-16

    The Frontal Assessment Battery (FAB) is a brief battery of six neuropsychological tasks designed to assess frontal lobe function at bedside [Neurology 55:1621-1626, 2000]. The six FAB tasks explore cognitive and behavioral domains that are thought to be under the control of the frontal lobes, most notably conceptualization and abstract reasoning, lexical verbal fluency and mental flexibility, motor programming and executive control of action, self-regulation and resistance to interference, inhibitory control, and environmental autonomy. We examined the sensitivity of performance on the FAB to frontal lobe damage in right-hemisphere-damaged first-ever stroke patients based on voxel-based lesion-behavior mapping. Voxel-based lesion-behavior mapping of FAB performance revealed that the integrity of the right anterior insula (BA13) is crucial for the FAB global composite score, for the FAB conceptualization score, as well as for the FAB inhibitory control score. Furthermore, the FAB conceptualization and mental flexibility scores were sensitive to damage of the right middle frontal gyrus (MFG; BA9). Finally, the FAB inhibitory control score was sensitive to damage of the right inferior frontal gyrus (IFG; BA44/45). These findings indicate that several FAB scores (including composite and item scores) provide valid measures of right hemispheric lateral frontal lobe dysfunction, specifically of focal lesions near the anterior insula, in the MFG and in the IFG.

  19. Frontal lobe connectivity and cognitive impairment in pediatric frontal lobe epilepsy.

    Science.gov (United States)

    Braakman, Hilde M H; Vaessen, Maarten J; Jansen, Jacobus F A; Debeij-van Hall, Mariette H J A; de Louw, Anton; Hofman, Paul A M; Vles, Johan S H; Aldenkamp, Albert P; Backes, Walter H

    2013-03-01

    Cognitive impairment is frequent in children with frontal lobe epilepsy (FLE), but its etiology is unknown. With functional magnetic resonance imaging (fMRI), we have explored the relationship between brain activation, functional connectivity, and cognitive functioning in a cohort of pediatric patients with FLE and healthy controls. Thirty-two children aged 8-13 years with FLE of unknown cause and 41 healthy age-matched controls underwent neuropsychological assessment and structural and functional brain MRI. We investigated to which extent brain regions activated in response to a working memory task and assessed functional connectivity between distant brain regions. Data of patients were compared to controls, and patients were grouped as cognitively impaired or unimpaired. Children with FLE showed a global decrease in functional brain connectivity compared to healthy controls, whereas brain activation patterns in children with FLE remained relatively intact. Children with FLE complicated by cognitive impairment typically showed a decrease in frontal lobe connectivity. This decreased frontal lobe connectivity comprised both connections within the frontal lobe as well as connections from the frontal lobe to the parietal lobe, temporal lobe, cerebellum, and basal ganglia. Decreased functional frontal lobe connectivity is associated with cognitive impairment in pediatric FLE. The importance of impairment of functional integrity within the frontal lobe network, as well as its connections to distant areas, provides new insights in the etiology of the broad-range cognitive impairments in children with FLE. Wiley Periodicals, Inc. © 2012 International League Against Epilepsy.

  20. Neuromorphic UAS Collision Avoidance

    Data.gov (United States)

    National Aeronautics and Space Administration — Collision avoidance for unmanned aerial systems (UAS) traveling at high relative speeds is a challenging task. It requires both the detection of a possible collision...

  1. Collision Repair Campaign

    Science.gov (United States)

    The Collision Repair Campaign targets meaningful risk reduction in the Collision Repair source category to reduce air toxic emissions in their communities. The Campaign also helps shops to work towards early compliance with the Auto Body Rule.

  2. Enabling Dissimilar Material Joining Using Friction Stir Scribe Technology

    Energy Technology Data Exchange (ETDEWEB)

    Hovanski, Yuri; Upadyay, Piyush; Kleinbaum, Sarah; Carlson, Blair; Boettcher, Eric; Ruokolainen, Robert

    2017-04-05

    One challenge in adapting welding processes to dissimilar material joining is the diversity of melting temperatures of the different materials. Although the use of mechanical fasteners and adhesives have mostly paved the way for near-term implementation of dissimilar material systems, these processes only accentuate the need for low-cost welding processes capable of joining dissimilar material components regardless of alloy, properties, or melting temperature. Friction stir scribe technology was developed to overcome the challenges of joining dissimilar material components where melting temperatures vary greatly, and properties and/or chemistry are not compatible with more traditional welding processes. Although the friction stir scribe process is capable of joining dissimilar metals and metal/polymer systems, a more detailed evaluation of several aluminum/steel joints is presented herein to demonstrate the ability to both chemically and mechanically join dissimilar materials.

  3. Finite Element Modeling and Optimization of Mechanical Joining Technology

    Science.gov (United States)

    Chenot, Jean-Loup; Bouchard, Pierre-Olivier; Massoni, Elisabeth; Mocellin, Katia; Lasne, Patrice

    2011-05-01

    The main scientific ingredients are recalled for developing a general finite element code and model accurately large plastic deformation of metallic materials during joining processes. Multi material contact is treated using the classical master and slave approach. Rupture may occur in joining processes or even be imposed in self piercing riveting and it must be predicted to evaluate the ultimate strength of joins. Damage is introduced with a generalized uncoupled damage criterion, or by utilizing a coupled formulation with a Lemaître law. Several joining processes are briefly analyzed in term of specific scientific issues: riveting, self piercing riveting, clinching, crimping, hemming and screwing. It is shown that not only the joining process can be successfully simulated and optimized, but also the strength of the assembly can be predicted in tension and in shearing.

  4. Fibrous dysplasia of the frontal sinus: an uncommon cause of frontal lobe abscess.

    Science.gov (United States)

    Aygun, D; Sahin, H

    2004-11-01

    Fibrous dysplasia of the cranial air sinuses is rarely reported in the literature. This is the first report of frontal lobe abscess (FLA) associated with fibrous dysplasia of the frontal sinus (FDFS). A 29-year-old female presented with seizures and acute confusion. Cranial computed tomography (CT) revealed fibrous dysplasia of the left frontal sinus and associated FLA. She was referred to the neurosurgical service and the abscess and dysplastic tissue were removed. Histological examination confirmed fibrous dysplasia. We review the radiological appearance of FDFS with FLA. Clinicians should be aware of the association between these two conditions.

  5. Prospective memory and frontal lobe function.

    Science.gov (United States)

    Neulinger, Kerryn; Oram, Joanne; Tinson, Helen; O'Gorman, John; Shum, David H K

    2016-01-01

    The study sought to examine the role of frontal lobe functioning in focal prospective memory (PM) performance and its relation to PM deficit in older adults. PM and working memory (WM) differences were studied in younger aged (n = 21), older aged (n = 20), and frontal injury (n = 14) groups. An event-based focal PM task was employed and three measures of WM were administered. The younger aged group differed from the other two groups in showing significantly higher scores on PM and on one of the WM measures, but there were no differences at a statistically significant level between the older aged group and the frontal injury groups on any of the memory measures. There were, however, some differences in correlations with a WM measure between groups. It is concluded that there are similarities and differences in the deficits in PM between older adults and patients with frontal lobe injury on focal as well as nonfocal PM tasks.

  6. Right Frontal White Matter and Tourette Syndrome

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2002-01-01

    Full Text Available An MRI volumetric analysis of frontal and nonfrontal gray and white matter was performed in 11 boys with Tourette syndrome (TS only, 14 with TS + ADHD, 12 with ADHD only, and 26 healthy boys, at the Kennedy Krieger Institute, Baltimore, MD.

  7. Infant Frontal Asymmetry Predicts Child Emotional Availability

    Science.gov (United States)

    Licata, Maria; Paulus, Markus; Kühn-Popp, Nina; Meinhardt, Jorg; Sodian, Beate

    2015-01-01

    While factors influencing maternal emotional availability (EA) have been well investigated, little is known about the development of child EA. The present longitudinal study investigated the role of frontal brain asymmetry in young children with regard to child EA (child responsiveness and involvement) in mother-child interaction in a sample of 28…

  8. Medial frontal cortex and response conflict: Evidence from human intracranial EEG and medial frontal cortex lesion

    NARCIS (Netherlands)

    Cohen, M.X.; Ridderinkhof, K.R.; Haupt, S.; Elger, C.E.; Fell, J.

    2008-01-01

    The medial frontal cortex (MFC) has been implicated in the monitoring and selection of actions in the face of competing alternatives, but much remains unknown about its functional properties, including electrophysiological oscillations, during response conflict tasks. Here, we recorded intracranial

  9. A Modeling Approach for Plastic-Metal Laser Direct Joining

    Science.gov (United States)

    Lutey, Adrian H. A.; Fortunato, Alessandro; Ascari, Alessandro; Romoli, Luca

    2017-09-01

    Laser processing has been identified as a feasible approach to direct joining of metal and plastic components without the need for adhesives or mechanical fasteners. The present work sees development of a modeling approach for conduction and transmission laser direct joining of these materials based on multi-layer optical propagation theory and numerical heat flow simulation. The scope of this methodology is to predict process outcomes based on the calculated joint interface and upper surface temperatures. Three representative cases are considered for model verification, including conduction joining of PBT and aluminum alloy, transmission joining of optically transparent PET and stainless steel, and transmission joining of semi-transparent PA 66 and stainless steel. Conduction direct laser joining experiments are performed on black PBT and 6082 anticorodal aluminum alloy, achieving shear loads of over 2000 N with specimens of 2 mm thickness and 25 mm width. Comparison with simulation results shows that consistently high strength is achieved where the peak interface temperature is above the plastic degradation temperature. Comparison of transmission joining simulations and published experimental results confirms these findings and highlights the influence of plastic layer optical absorption on process feasibility.

  10. Innovative cold joining technologies based on tube forming

    Directory of Open Access Journals (Sweden)

    Alves Luis M.

    2015-01-01

    Full Text Available This paper is focused on innovative cold joining technologies for connecting tubes and fixing tubes to sheets. The proposed technologies are based on the utilization of plastic instability waves in thin-walled tubes subjected to axial compression and may be seen as an alternative to conventional joining technologies based on mechanical fixing with fasteners, welding and structural adhesive bonding. Besides allowing connecting dissimilar materials and being successfully employed in fixture conditions that are difficult and costly to achieve by means of conventional joining the new proposed technologies also cope with the growing concerns on the demand, lifecycle and recycling of materials.

  11. Joining of parts via magnetic heating of metal aluminum powders

    Science.gov (United States)

    Baker, Ian

    2013-05-21

    A method of joining at least two parts includes steps of dispersing a joining material comprising a multi-phase magnetic metal-aluminum powder at an interface between the at least two parts to be joined and applying an alternating magnetic field (AMF). The AMF has a magnetic field strength and frequency suitable for inducing magnetic hysteresis losses in the metal-aluminum powder and is applied for a period that raises temperature of the metal-aluminum powder to an exothermic transformation temperature. At the exothermic transformation temperature, the metal-aluminum powder melts and resolidifies as a metal aluminide solid having a non-magnetic configuration.

  12. Genetics Home Reference: autosomal dominant nocturnal frontal lobe epilepsy

    Science.gov (United States)

    ... Health Conditions ADNFLE Autosomal dominant nocturnal frontal lobe epilepsy Printable PDF Open All Close All Enable Javascript ... collapse boxes. Description Autosomal dominant nocturnal frontal lobe epilepsy ( ADNFLE ) is an uncommon form of epilepsy that ...

  13. ASKAP Joins the Hunt for Mysterious Bursts

    Science.gov (United States)

    Kohler, Susanna

    2017-05-01

    A new telescope, the Australian Square Kilometre Array Pathfinder (ASKAP), has joined the search for energetic and elusive fast radio bursts. And in just a few days of looking, its already had success!Elusive TransientsThe Parkes radio telescope, which has detected all but five of the fast radio bursts published to date, has a very narrow field of view. [CSIRO]Fast radio bursts are mysterious millisecond-duration radio pulses that were first discovered around a decade ago. Since that time particularly in recent years weve made some progress toward the goal of localizing them. Were now fairly convinced that fast radio bursts come from outside of the galaxy, and yet theyre enormously bright orders of magnitude more luminous than any pulse seen from the Milky Way.Better identification of where these mysterious bursts come from would help us to determine what they are. But so far, weve discovered only around 30 such bursts, despite the fact that theyre estimated to occur at a rate of 3,000 events per day across the whole sky.Why are they so hard to find? Due to their short duration, effective detection would require instantaneous coverage of a very large fraction of the sky. The Parkes radio telescope which has detected all but five of the fast radio bursts published to date has a field of view spanning less than a square degree,significantly limiting our ability to rapidly survey for these transients.FRB 170107s band-averaged pulse (top) and dynamic spectrum (bottom). [Bannister et al. 2017]A New Array in TownA new player is now on the scene, however, and its already had huge success. ASKAP is a wide-field radio telescope made up of an array of 12-meter antennas. Using phased-array-feed technology, ASKAP is able to instantaneously observe an effective area of 160 square degrees an enormous field compared to Parkes 0.6 square degrees! This capability significantly increases our chances of being able to detect fast radio bursts.In a new study led by Keith Bannister

  14. Nocturnal frontal lobe epilepsy in mucopolysaccharidosis.

    Science.gov (United States)

    Bonanni, Paolo; Volzone, Anna; Randazzo, Giovanna; Antoniazzi, Lisa; Rampazzo, Angelica; Scarpa, Maurizio; Nobili, Lino

    2014-10-01

    Nocturnal frontal lobe epilepsy (NFLE) is an epileptic syndrome that is primarily characterized by seizures with motor signs occurring almost exclusively during sleep. We describe 2 children with mucopolysaccharidosis (MPS) who were referred for significant sleep disturbance. Long term video-EEG monitoring (LT-VEEGM) demonstrated sleep-related hypermotor seizures consistent with NFLE. No case of sleep-related hypermotor seizures has ever been reported to date in MPS. However, differential diagnosis with parasomnias has been previously discussed. The high frequency of frontal lobe seizures causes sleep fragmentation, which may result in sleep disturbances observed in at least a small percentage of MPS patients. We suggest monitoring individuals with MPS using periodic LT-VEEGM, particularly when sleep disorder is present. Moreover, our cases confirm that NFLE in lysosomal storage diseases may occur, and this finding extends the etiologic spectrum of NFLE. Copyright © 2014 The Japanese Society of Child Neurology. Published by Elsevier B.V. All rights reserved.

  15. Frontal lobe epilepsy and EEG: Neurophysiological approach

    OpenAIRE

    García López, Beatriz

    2015-01-01

    La epilepsia del lóbulo frontal es la segunda más frecuente en la mayoría de las series publicadas, después de la epilepsia temporal. Sus características clínicas y electroencefalográficas son muy variadas, lo que hace de su diagnóstico y tratamiento un reto en la práctica clínica. Las crisis frontales suelen aparecen en "clusters", con frecuencia generalizan y el aspecto electroencefalográfico de la actividad intercrítica y crítica suele ser difícil de interpretar por la gran difusión que su...

  16. Potentials of Industrie 4.0 and Machine Learning for Mechanical Joining

    OpenAIRE

    Jäckel, Mathias

    2017-01-01

    -Sensitivity analysis of the influence of component properties and joining parameters on the joining result for self-pierce riveting -Possibilities to link mechanical joining technologies with the automotive process chain for quality and flexibility improvements -Potential of using machine learning to reduce automotive product development cycles in relation to mechanical joining -Datamining for machine learning at mechanical joining

  17. Intraparenchymal schwannoma of the frontal lobe.

    Directory of Open Access Journals (Sweden)

    Deogaonkar M

    1994-10-01

    Full Text Available A 45 year old woman with bifrontal headaches and progressive diminution in vision over 6 months was found to have bilateral papilloedema. CT scan showed large right frontal lesion with surrounding oedema. Right basal frontotemporal craniotomy was performed to excise the multinodular, intraparenchymatous tumor. Hispathology confirmed the diagnosis of schwannoma. Post-operative course was uneventful with disappearance of pre-operative signs and symptoms.

  18. Frontal lobe function in temporal lobe epilepsy

    Science.gov (United States)

    Stretton, J.; Thompson, P.J.

    2012-01-01

    Summary Temporal lobe epilepsy (TLE) is typically associated with long-term memory dysfunction. The frontal lobes support high-level cognition comprising executive skills and working memory that is vital for daily life functioning. Deficits in these functions have been increasingly reported in TLE. Evidence from both the neuropsychological and neuroimaging literature suggests both executive function and working memory are compromised in the presence of TLE. In relation to executive impairment, particular focus has been paid to set shifting as measured by the Wisconsin Card Sorting Task. Other discrete executive functions such as decision-making and theory of mind also appear vulnerable but have received little attention. With regard to working memory, the medial temporal lobe structures appear have a more critical role, but with emerging evidence of hippocampal dependent and independent processes. The relative role of underlying pathology and seizure spread is likely to have considerable bearing upon the cognitive phenotype and trajectory in TLE. The identification of the nature of frontal lobe dysfunction in TLE thus has important clinical implications for prognosis and surgical management. Longitudinal neuropsychological and neuroimaging studies assessing frontal lobe function in TLE patients pre- and postoperatively will improve our understanding further. PMID:22100147

  19. Role of Frontal Alpha Oscillations in Creativity

    Science.gov (United States)

    Lustenberger, Caroline; Boyle, Michael R.; Foulser, A. Alban; Mellin, Juliann M.; Fröhlich, Flavio

    2015-01-01

    Creativity, the ability to produce innovative ideas, is a key higher-order cognitive function that is poorly understood. At the level of macroscopic cortical network dynamics, recent EEG data suggests that cortical oscillations in the alpha frequency band (8 – 12 Hz) are correlated with creative thinking. However, whether alpha oscillations play a fundamental role in creativity has remained unknown. Here we show that creativity is increased by enhancing alpha power using 10 Hz transcranial alternating current stimulation (10Hz-tACS) of the frontal cortex. In a study of 20 healthy participants with a randomized, balanced cross-over design, we found a significant improvement of 7.4% in the Creativity Index measured by the Torrance Test of Creative Thinking, a comprehensive and most frequently used assay of creative potential and strengths. In a second similar study with 20 subjects, 40Hz-tACS was used in instead of 10Hz-tACS to rule out a general “electrical stimulation” effect. No significant change in the Creativity Index was found for such frontal gamma stimulation. Our results suggest that alpha activity in frontal brain areas is selectively involved in creativity; this enhancement represents the first demonstration of specific neuronal dynamics that drive creativity and can be modulated by non-invasive brain stimulation. Our findings agree with the model that alpha recruitment increases with internal processing demands and is involved in inhibitory top-down control, which is an important requirement for creative ideation. PMID:25913062

  20. Coastal river plumes: Collisions and coalescence

    Science.gov (United States)

    Warrick, Jonathan; Farnsworth, Katherine L

    2017-01-01

    Plumes of buoyant river water spread in the ocean from river mouths, and these plumes influence water quality, sediment dispersal, primary productivity, and circulation along the world’s coasts. Most investigations of river plumes have focused on large rivers in a coastal region, for which the physical spreading of the plume is assumed to be independent from the influence of other buoyant plumes. Here we provide new understanding of the spreading patterns of multiple plumes interacting along simplified coastal settings by investigating: (i) the relative likelihood of plume-to-plume interactions at different settings using geophysical scaling, (ii) the diversity of plume frontal collision types and the effects of these collisions on spreading patterns of plume waters using a two-dimensional hydrodynamic model, and (iii) the fundamental differences in plume spreading patterns between coasts with single and multiple rivers using a three-dimensional hydrodynamic model. Geophysical scaling suggests that coastal margins with numerous small rivers (watershed areas  100,000 km2). When two plume fronts meet, several types of collision attributes were found, including refection, subduction and occlusion. We found that the relative differences in pre-collision plume densities and thicknesses strongly influenced the resulting collision types. The three-dimensional spreading of buoyant plumes was found to be influenced by the presence of additional rivers for all modeled scenarios, including those with and without Coriolis and wind. Combined, these results suggest that plume-to-plume interactions are common phenomena for coastal regions offshore of the world’s smaller rivers and for coastal settings with multiple river mouths in close proximity, and that the spreading and fate of river waters in these settings will be strongly influenced by these interactions. We conclude that new investigations are needed to characterize how plumes interact offshore of river mouths to

  1. Joining Silicon Carbide Components for Space Propulsion Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I program will identify the joining materials and demonstrate the processes that are suited for construction of advanced ceramic matrix composite...

  2. Low Temperature Active Joining of Structural and Electronic Composites

    National Research Council Canada - National Science Library

    Smith, Ronald

    2003-01-01

    ... for space platform structures and electronics, where Al-MMC's are finding application. S-Bond joining has joint capability from 190 - 350 C, depending on which S-Bond filler, Alloy 220 or Alloy 400 is used...

  3. Microwave joining of SiC ceramics and composites

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, I.; Silberglitt, R.; Tian, Y.L. [FM Technologies, Inc., Fairfax, VA (United States); Katz, J.D. [Los Alamos National Lab., NM (United States)

    1997-04-01

    Potential applications of SiC include components for advanced turbine engines, tube assemblies for radiant burners and petrochemical processing and heat exchangers for high efficiency electric power generation systems. Reliable methods for joining SiC are required in order to cost-effectively fabricate components for these applications from commercially available shapes and sizes. This manuscript reports the results of microwave joining experiments performed using two different types of SiC materials. The first were on reaction bonded SiC, and produced joints with fracture toughness equal to or greater than that of the base material over an extended range of joining temperatures. The second were on continuous fiber-reinforced SiC/SiC composite materials, which were successfully joined with a commercial active brazing alloy, as well as by using a polymer precursor.

  4. Joining of Aluminium Alloy Sheets by Rectangular Mechanical Clinching

    International Nuclear Information System (INIS)

    Abe, Y.; Mori, K.; Kato, T.

    2011-01-01

    A mechanical clinching has the advantage of low running costs. However, the joint strength is not high. To improve the maximum load of the joined sheets by a mechanical clinching, square and rectangular mechanical clinching were introduced. In the mechanical clinching, the two sheets are mechanically joined by forming an interlock between the lower and upper sheets by the punch and die. The joined length with the interlock was increased by the rectangular punch and die. The deforming behaviours of the sheets in the mechanical clinching were investigated, and then the interlock in the sheets had distribution in the circumference of the projection. Although the interlocks were formed in both projection side and diagonal, the interlock in the diagonal was smaller because of the long contact length between the lower sheet and the die cavity surface. The maximum load of the joined sheets by the rectangular mechanical clinching was two times larger than the load by the round mechanical clinching.

  5. Joining Silicon Carbide Components for Space Propulsion, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I program will identify the joining materials and demonstrate the processes that are suited for construction of advanced ceramic matrix composite...

  6. Joining SI3N4 for Advanced Turbomachinery Applications

    Energy Technology Data Exchange (ETDEWEB)

    GLASS, S. JILL; LOEHMAN, RONALD E.; HOSKING, F. MICHAEL; STEPHENS JR., JOHN J.; VIANCO, PAUL T.; NEILSEN, MICHAEL K.; WALKER, CHARLES A.; POLLINGER, J.P.; MAHONEY, F.M.; QUILLEN, B.G.

    2000-07-01

    The main objective of this project was to develop reliable, low-cost techniques for joining silicon nitride (Si{sub 3}N{sub 4}) to itself and to metals. For Si{sub 3}N{sub 4} to be widely used in advanced turbomachinery applications, joining techniques must be developed that are reliable, cost-effective, and manufacturable. This project addressed those needs by developing and testing two Si{sub 3}N{sub 4} joining systems; oxynitride glass joining materials and high temperature braze alloys. Extensive measurements were also made of the mechanical properties and oxidation resistance of the braze materials. Finite element models were used to predict the magnitudes and positions of the stresses in the ceramic regions of ceramic-to-metal joints sleeve and butt joints, similar to the geometries used for stator assemblies.

  7. Fastening, coupling and joining technique between diaspora and irredenta

    Science.gov (United States)

    Bauer, C.-O.

    1980-06-01

    The problem of eliminating the present divergence and shattering (diaspora) in the treatment of problems of the fastening, coupling, and joining technique on different technical branches is examined. It is shown that by an appropriate independence the fastening, coupling and joining techniques can recognize and consequently utilize the numerous performance reserves which are concealed by the present organization and action due to the lack of systematically tended works.

  8. Top scientists join Stephen Hawking at Perimeter Institute

    Science.gov (United States)

    Banks, Michael

    2009-03-01

    Nine leading researchers are to join Stephen Hawking as visiting fellows at the Perimeter Institute for Theoretical Physics in Ontario, Canada. The researchers, who include string theorists Leonard Susskind from Stanford University and Asoka Sen from the Harisch-Chandra Research Institute in India, will each spend a few months of the year at the institute as "distinguished research chairs". They will be joined by another 30 scientists to be announced at a later date.

  9. JOINING DISSIMILAR MATERIALS USING FRICTION STIR SCRIBE TECHNIQUE

    Energy Technology Data Exchange (ETDEWEB)

    Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep; Fifield, Leonard S.

    2016-09-01

    Development of robust and cost effective method of joining dissimilar materials can provide a critical pathway to enable widespread use of multi-material design and components in mainstream industrial applications. The use of multi-material components such as Steel-Aluminum, Aluminum-Polymer allows design engineers to optimize material utilization based on service requirements and often lead weight and cost reductions. However producing an effective joint between materials with vastly different thermal, microstructural and deformation response is highly problematic using conventional joining and /or fastening methods. This is especially challenging in cost sensitive high volume markets that largely rely on low–cost joining solutions. Friction Stir Scribe technology was developed to meet the demands of joining materials with drastically different properties and melting regimes. The process enables joining of light metals like Magnesium and Aluminum to high temperature materials like Steels and Titanium. Additionally viable joints between polymer composites and metal can also be made using this method. This paper will present state of the art, progress made and challenges associated with this innovative derivative of Friction Stir welding in reference to joining dissimilar metals and polymer/metal combinations.

  10. Joining Dissimilar Materials Using Friction Stir Scribe Technique

    Energy Technology Data Exchange (ETDEWEB)

    Upadhyay, Piyush [Pacific Northwest National Laboratory, Richland 99352, WA e-mail: piyush.upadhyay@pnnl.gov; Hovanski, Yuri [Pacific Northwest National Laboratory, Richland 99352, WA; Jana, Saumyadeep [Pacific Northwest National Laboratory, Richland 99352, WA; Fifield, Leonard S. [Pacific Northwest National Laboratory, Richland 99352, WA

    2016-10-03

    Development of a robust and cost-effective method of joining dissimilar materials could provide a critical pathway to enable widespread use of multi-material designs and components in mainstream industrial applications. The use of multi-material components such as steel-aluminum and aluminum-polymer would allow design engineers to optimize material utilization based on service requirements and could often lead to weight and cost reductions. However, producing an effective joint between materials with vastly different thermal, microstructural, and deformation responses is highly problematic using conventional joining and/or fastening methods. This is especially challenging in cost sensitive, high volume markets that largely rely on low cost joining solutions. Friction stir scribe technology was developed to meet the demands of joining materials with drastically different properties and melting regimes. The process enables joining of light metals like magnesium and aluminum to high temperature materials like steel and titanium. Viable joints between polymer composites and metal can also be made using this method. This paper will present the state of the art, progress made, and challenges associated with this innovative derivative of friction stir welding in reference to joining dissimilar metals and polymer/metal combinations.

  11. Alopecia frontal fibrosante: relato de seis casos Frontal fibrosing alopecia: report of six cases

    Directory of Open Access Journals (Sweden)

    Fabiane Mulinari-Brenner

    2007-10-01

    Full Text Available Alopecia frontal fibrosante é forma progressiva de alopecia cicatricial. Os casos iniciais foram relatados a partir 1994, na Austrália, em pacientes do sexo feminino pós-menopausa. Desde então inúmeros casos foram descritos na literatura sugerindo que ela é mais prevalente do que inicialmente se supunha. Seu curso progressivo se assemelha ao da alopecia androgenética; histologicamente, entretanto, o infiltrado liquenóide é evidente. O artigo relata seis casos brasileiros e discute a alopecia frontal fibrosante dentro do grupo das alopecias cicatriciais, como variante do líquen plano pilar.Frontal fibrosing alopecia is a progressive cicatricial alopecia. The first cases were described in Australia in postmenopausal women, in 1994. Since then, numerous cases were reported, suggesting that frontal fibrosing alopecia is more prevalent than initially thought. Its progressive course in postmenopausal women, clinically resembles androgenetic alopecia; however, histologically, lichenoid infiltrate is evident. This article report six brazilian cases of frontal fibrosing alopecia and discusses them in the context of cicatricial alopecias, as a variant of lichen planopilaris.

  12. Hadron-nucleus collisions

    International Nuclear Information System (INIS)

    Strugalski, Z.

    1981-01-01

    Qualitative picture of high energy hadron-nucleus collision process, emerging from the analysis of experimental data, is presented. Appropriate description procedure giving a possibility of reproducing various characteristics of this process in terms of the data on elementary hadron-nucleon interaction is proposed. Formula reproducing hadron-nucleus collision cross sections is derived. Inelastic collision cross sections for pion-nucleus and proton-nucleus reactions at wide energy interval are calculated for Pb, Ag, and Al targets. A-dependence of cross sections for pion-nucleus and proton-nucleus collisions at nearly 50 GeV/c momentum were calculated and compared with existing experimental data. Energy dependence of cross sections for hadron-nucleus collisions is determined simply by energy dependence of corresponding cross sections for hadron-nucleon collisions; A-dependence is determined simply by nuclear sizes and nucleon density distributions in nuclei

  13. LEXUS heavy ion collisions

    CERN Document Server

    Sang Yong Jeon

    1997-01-01

    We use a Glauber-like approach to describe very energetic nucleus- nucleus collisions as a sequence of binary nucleon-nucleon collisions. No free parameters are needed: all the information comes from simple parametrizations of nucleon-nucleon collision data. Produced mesons are assumed not to interact with each other or with the original baryons. Comparisons are made to published experimental measurements of baryon rapidity and transverse momentum distributions, negative hadron rapidity and transverse momentum distributions, average multiplicities of pions, kaons, hyperons, and antihyperons, and zero degree energy distributions for sulfur-sulfur collisions at 200 GeV/c per nucleon and for lead-lead collisions at 158 GeV/c per nucleon. Good agreement is found except that the number of strange particles produced, especially antihyperons, is too small compared with experiment. We call this model LEXUS: Linear EXtrapolation of Ultrarelativistic nucleon-nucleon Scattering to heavy ion collisions. (11 refs).

  14. Unilateral spatial neglect due to right frontal lobe haematoma.

    OpenAIRE

    Maeshima, S; Funahashi, K; Ogura, M; Itakura, T; Komai, N

    1994-01-01

    Two patients with unilateral spatial neglect caused by right frontal lobe lesions underwent cerebral blood flow studies. A 54-year-old, right-handed woman developed left hemiplegia and frontal lobe neglect associated with cerebral haemorrhage after surgical excision of a frontal tumour. A 66-year-old, right-handed woman developed a haemorrhage in the right frontal lobe caused by rupture of an aneurysm. This was followed by left hemiplegia and frontal lobe neglect. In both cases, 123I-iodoamph...

  15. Impairments in proverb interpretation following focal frontal lobe lesions☆

    Science.gov (United States)

    Murphy, Patrick; Shallice, Tim; Robinson, Gail; MacPherson, Sarah E.; Turner, Martha; Woollett, Katherine; Bozzali, Marco; Cipolotti, Lisa

    2013-01-01

    The proverb interpretation task (PIT) is often used in clinical settings to evaluate frontal “executive” dysfunction. However, only a relatively small number of studies have investigated the relationship between frontal lobe lesions and performance on the PIT. We compared 52 patients with unselected focal frontal lobe lesions with 52 closely matched healthy controls on a proverb interpretation task. Participants also completed a battery of neuropsychological tests, including a fluid intelligence task (Raven’s Advanced Progressive Matrices). Lesions were firstly analysed according to a standard left/right sub-division. Secondly, a finer-grained analysis compared the performance of patients with medial, left lateral and right lateral lesions with healthy controls. Thirdly, a contrast of specific frontal subgroups compared the performance of patients with medial lesions with patients with lateral frontal lesions. The results showed that patients with left frontal lesions were significantly impaired on the PIT, while in patients with right frontal lesions the impairments approached significance. Medial frontal patients were the only frontal subgroup impaired on the PIT, relative to healthy controls and lateral frontal patients. Interestingly, an error analysis indicated that a significantly higher number of concrete responses were found in the left lateral subgroup compared to healthy controls. We found no correlation between scores on the PIT and on the fluid intelligence task. Overall our results suggest that specific regions of the frontal lobes contribute to the performance on the PIT. PMID:23850600

  16. Development of Joining Technologies for the ITER Blanket First Wall

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Byoung Kwon; Jung, Yang Il; Park, Dong Jun; Kim, Hyun Gil; Park, Sang Yoon; Park, Jeong Yong; Jeong, Yong Hwan; Lee, Dong Won; Kim, Suk Kwon [KAERI, Daejeon (Korea, Republic of)

    2011-01-15

    The design of the ITER blanket first wall includes the Beryllium amour tiles joined to CuCrZr heat sink with stainless steel cooling tubes. For the ITER application, the Be/CuCrZr/SS joint was proposed as a first wall material. The joining of Be/CuCrZr as well as CuCrZr/SS was generally carried out by using a hot isostatic pressing (CuC) in many countries. The joining strength for Be/CuCrZr is relatively lower than that for CuCrZr/SS, since we usually forms surface oxides (BeO) and brittle a metallics with Cu. Therefore, the joining technology for the Be/CuCrZr joint has been investigated. Be is apt to adsorb oxygen in an air atmosphere, so we should be etched to eliminate the surface pre-oxide using a chemical solution and Ar ions in a vacuum chamber. Then we is coated with a first was to prevent further oxidation. The kinds of a first we are chosen to be able to enhance the joining strength as inhibiting excessive be diffusion. The performance of the Be/CuCrZr/SS joint used for the ITER first wall is primarily dependent on the joining strength of the Be/CuCrZr interface. The Cr/Cu and Ti/Cr/Cu interlayers enabled the successful joining of be tile to CuCrZr plate. Moreover, ion-beam assisted deposition (IBAD) increased joining strength of the Be/CuCrZr joint mock-ups. IBAD induced the increased packing of depositing atoms, which resulted in denser and more adhesive interlayers. The interlayers formed by IBAD process revealed about 40% improved resistance to the scratch test. It is suggested that the improved adhesion of coating interlayers enabled tight joining of Be and CuCrZr blocks. As compared to without IBAD coating, the shear strength as well as the 4-point bend strength were increased more than 20% depending on interlayer types and coating conditions

  17. Development of Joining Technologies for the ITER Blanket First Wall

    International Nuclear Information System (INIS)

    Choi, Byoung Kwon; Jung, Yang Il; Park, Dong Jun; Kim, Hyun Gil; Park, Sang Yoon; Park, Jeong Yong; Jeong, Yong Hwan; Lee, Dong Won; Kim, Suk Kwon

    2011-01-01

    The design of the ITER blanket first wall includes the Beryllium amour tiles joined to CuCrZr heat sink with stainless steel cooling tubes. For the ITER application, the Be/CuCrZr/SS joint was proposed as a first wall material. The joining of Be/CuCrZr as well as CuCrZr/SS was generally carried out by using a hot isostatic pressing (CuC) in many countries. The joining strength for Be/CuCrZr is relatively lower than that for CuCrZr/SS, since we usually forms surface oxides (BeO) and brittle a metallics with Cu. Therefore, the joining technology for the Be/CuCrZr joint has been investigated. Be is apt to adsorb oxygen in an air atmosphere, so we should be etched to eliminate the surface pre-oxide using a chemical solution and Ar ions in a vacuum chamber. Then we is coated with a first was to prevent further oxidation. The kinds of a first we are chosen to be able to enhance the joining strength as inhibiting excessive be diffusion. The performance of the Be/CuCrZr/SS joint used for the ITER first wall is primarily dependent on the joining strength of the Be/CuCrZr interface. The Cr/Cu and Ti/Cr/Cu interlayers enabled the successful joining of be tile to CuCrZr plate. Moreover, ion-beam assisted deposition (IBAD) increased joining strength of the Be/CuCrZr joint mock-ups. IBAD induced the increased packing of depositing atoms, which resulted in denser and more adhesive interlayers. The interlayers formed by IBAD process revealed about 40% improved resistance to the scratch test. It is suggested that the improved adhesion of coating interlayers enabled tight joining of Be and CuCrZr blocks. As compared to without IBAD coating, the shear strength as well as the 4-point bend strength were increased more than 20% depending on interlayer types and coating conditions

  18. Laser beam joining of material combinations for automotive applications

    Science.gov (United States)

    Schubert, Emil; Zerner, Ingo; Sepold, Gerd

    1997-08-01

    An ideal material for automotive applications would combine the following properties: high corrosion resistance, high strength, high stiffness and not at least a low material price. Today a single material is not able to meet all these requirements. Therefore, in the future different materials will be placed where they meet the requirements best. The result of this consideration is a car body with many different alloys and metals, which have to be joined to one another. BIAS is working on the development of laser based joining technologies for different material combinations, especially for thin sheets used in automotive applications. One result of the research is a joining technology for an aluminum-steel-joint. Using a Nd:YAG laser the problem of brittle intermetallic phases between these materials was overcome. Using suitable temperature-time cycles, elected by a FEM-simulation, the thickness of intermetallic phases was kept below 10 micrometers . This technology was also applied to coated steels, which were joined with different aluminum alloys. Further it is demonstrated that titanium alloys, e.g. used for racing cars, can also be joined with aluminum alloys.

  19. New Joining Technology for Optimized Metal/Composite Assemblies

    Directory of Open Access Journals (Sweden)

    Holger Seidlitz

    2014-01-01

    Full Text Available The development of a new joining technology, which is used to manufacture high strength hybrid constructions with thermoplastic composites (FRP and metals, is introduced. Similar to natural regulation effects at trees, fibers around the FRP joint become aligned along the lines of force and will not be destroyed by the joining process. This is achieved by the local utilization of the specific plastic flow properties of the FRT and metal component. Compared with usual joining methods—such as flow drill screws, blind and self-piercing rivets—noticeably higher tensile properties can be realized through the novel process management. The load-bearing capability increasing effect could be proved on hybrid joints with hot-dip galvanized steel HX420LAD and orthotropic glass—as well as carbon—fiber reinforced plastics. The results, which were determined in tensile-shear and cross-shear tests according to DIN EN ISO 14273 and DIN EN ISO 14272, are compared with holding loads of established joining techniques with similar joining point diameter and material combinations.

  20. Surface-activated joining method for surveillance coupon reconstitution

    International Nuclear Information System (INIS)

    Kaihara, Shoichiro; Nakamura, Terumi

    1993-01-01

    As nuclear power plants approach the end of their license periods and license renewal is contemplated, there is an increasing need to expand the data base of mechanical properties obtainable from archival surveillance specimens. A new joining method for reconstituting broken Charpy specimens is being developed, the objective being to retain the original properties of the material in the process. The new method is called surface-activated joining (SAJ). It is designed to obtain a good junction without applying extra heating and deformation. In particular, the purpose of SAJ is to minimize the width of the heat-affected zone (HAZ) and to decrease the maximum temperature experienced by the specimen during reconsolidation of the two pieces. Generally, machined metal surfaces are contaminated with films of oxide, adsorbed gas, oil, or other vapors that impede bonding of surfaces during joining. However, if surface contamination is removed and the two surfaces are mated as closely as possible, joining can be achieved at low temperatures and modest stress levels. In order to apply the SAJ method, the following requirements must be met: (1) inert atmosphere to protect the surfaces from atmospheric gases and oxidation; (2) removal of the existing contamination layers to activate the surfaces; and (3) method for bringing the two surfaces into very intimate contact prior to joining

  1. Cohesive delamination and frictional contact on joining surface via XFEM

    Directory of Open Access Journals (Sweden)

    Francesco Parrinello

    2018-02-01

    Full Text Available In the present paper, the complex mechanical behaviour of the surfaces joining two differentbodies is analysed by a cohesive-frictional interface constitutive model. The kinematical behaviouris characterized by the presence of discontinuous displacement fields, that take place at the internalconnecting surfaces, both in the fully cohesive phase and in the delamination one. Generally, in order tocatch discontinuous displacement fields, internal connecting surfaces (adhesive layers are modelled bymeans of interface elements, which connect, node by node, the meshes of the joined bodies, requiringthe mesh to be conforming to the geometry of the single bodies and to the relevant connecting surface.In the present paper, the Extended Finite Element Method (XFEM is employed to model, both fromthe geometrical and from the kinematical point of view, the whole domain, including the connectedbodies and the joining surface. The joining surface is not discretized by specific finite elements, butit is defined as an internal discontinuity surface, whose spatial position inside the mesh is analyticallydefined. The proposed approach is developed for two-dimensional composite domains, formed by twoor more material portions joined together by means of a zero thickness adhesive layer. The numericalresults obtained with the proposed approach are compared with the results of the classical interfacefinite element approach. Some examples of delamination and frictional contact are proposed withlinear, circular and curvilinear adhesive layer.

  2. Ball Collision Experiments

    Science.gov (United States)

    Cross, R.

    2015-01-01

    Experiments are described on collisions between two billiard balls and between a bat and a ball. The experiments are designed to extend a student's understanding of collision events and could be used either as a classroom demonstration or for a student project.

  3. Cranialization of the frontal sinus-the final remedy for refractory chronic frontal sinusitis

    NARCIS (Netherlands)

    van Dijk, J. Marc C.; Wagemakers, Michiel; Korsten-Meijer, Astrid G. W.; Buiter, C. T. Kees; van der Laan, Bernard F. A. M.; Mooij, Jan Jakob A.

    Object. Chronic sinusitis can be a debilitating disease with significant impact on quality of life. Frontal sinusitis has a relatively low prevalence, but complications can be severe due to its anatomical location. After failure of conservative measures, typically endoscopic procedures are performed

  4. Joining NbTi superconductors by ultrasonic welding

    International Nuclear Information System (INIS)

    Hafstrom, J.W.; Killpatrick, D.H.; Niemann, R.C.; Purcell, J.R.; Thresh, H.R.

    1976-01-01

    An important consideration in the design and construction of large, high-field, superconducting magnets is the capability to fabricate reliable, high-strength, low-resistance joints. A process for joining NbTi, copper stabilized, superconducting composites by ultrasonic welding is described. This process yields a joint strength comparable to that of the superconducting composite and a resistivity significantly lower than achieved by conventional soft soldering. The superconducting properties of the composite are not affected by the joining process. Scarfing the joint to maintain a constant conductor cross section does not degrade its electrical or mechanical properties. The application of the ultrasonic joining process, including process control, scarfing, and NDT procedures, in the construction of the superconducting magnet (U.S. SCMS) for the joint U. S. -- Soviet MHD program is described

  5. Advances in Solid State Joining of High Temperature Alloys

    Science.gov (United States)

    Ding, Jeff; Schneider, Judy

    2011-01-01

    Many of the metals used in the oil and gas industry are difficult to fusion weld including Titanium and its alloys. Solid state joining processes are being pursued as an alternative process to produce robust structures more amenable to high pressure applications. Various solid state joining processes include friction stir welding (FSW) and a patented modification termed thermal stir welding (TSW). The configuration of TSWing utilizes an induction coil to preheat the material minimizing the burden on the weld tool extending its life. This provides the ability to precisely select and control the temperature to avoid detrimental changes to the microstructure. The work presented in this presentation investigates the feasibility of joining various titanium alloys using the solid state welding processes of FSW and TSW. Process descriptions and attributes of each weld process will be presented. Weld process set ]up and welding techniques will be discussed leading to the challenges experienced. Mechanical property data will also be presented.

  6. Porous vycor glass tube joined to borosilicate glass

    Science.gov (United States)

    Abe, Shinichi; Kikuchi, Takemitsu; Onodera, Shinji

    1992-09-01

    Porous glass can absorb various size of molecules with large surface area even in high temperature. However, it is difficult to use porous glass tubes at high-temperature, for example as a separation membrane for hydrogen condensation, because adhesives at joining sites could be damaged. In this study, welding of a porous glass tube and a glass tube was attempted to develop a gas separation membrane used at 500 C. Since forms present in porous glass may cause crack at high temperature, it is necessary to remove such forms by heat processing. Such porous glass is called to be porous vycor glass, which contains quartz 6 percents, and can be joined with a quartz tube. As a result, a gas separator with porous glass membrane which is joined by this process could endure high temperature up to 600 C and could maintain high vacuum.

  7. ROMANIA'S MACROECONOMIC ACHIEVEMENTS FOR JOINING THE UNIQUE EUROPEAN CURENCY

    Directory of Open Access Journals (Sweden)

    SILVIA POPESCU

    2011-04-01

    Full Text Available The Romanian government has announced plans to join the eurozone by 2015. Currently, the leu is not yet part of ERM II but plans to join in 2010-2012. The economic advantages of the monetary union grow with expansion of the Euro zone. There is also a high level of skepticism; the main fear about the Euro is the inflation –that is considerable promoted by the Euro currency’s exchange rate in comparison with 2002; another restraint is due to member states inability to establish their own interest rates. The IMF arose the option of joining the Euro zone criteria relaxing. A one-sided Euro’s joining was suggested by International Monetary Fund on March-April 2009, in a confidential report mentioned by The Financial Times as the emergent states in Central and Eastern Europe to be able to pass to the unique currency, but not being represented in the Central European Bank Board. By its side, CEB considers that emergent states of the European Union must not pass to the unique currency unilaterally, because such a fact could under-mine the trust in Euro currency worldwide. This option would hardly deepen the macroeconomic controversies inside the Euro zone and would contradict the previous conditions already imposed. An acceptable solution could be the fastening of emergent countries joining the Exchange Rate Mechanism 2, after they are aware of risks arisen by such a step. The European Commission endorses in the Convergence Report on 2010 that Romania doesn’t meet any criteria needed by passing to the unique European currency, respectively: prices stability; budget position of the government; stability of exchange rate; interest convergence on long run and there are also law impediments. Our paper discusses arguments for a faster passing to the Euro currency versus arguments for a late joining the Euro currency in Romania.

  8. Process optimization of joining by upset bulging with local heating

    Science.gov (United States)

    Rusch, Michael; Almohallami, Amer; Sviridov, Alexander; Bonk, Christian; Behrens, Bernd-Arno; Bambach, Markus

    2017-10-01

    Joining by upset bulging is a mechanical joining method where axial load is applied to a tube to form two revolving bulges, which clamp the parts to be joined and create a force and form fit. It can be used to join tubes with other structures such as sheets, plates, tubes or profiles of the same or different materials. Other processes such as welding are often limited in joining multi-material assemblies or high-strength materials. With joining by upset bulging at room temperature, the main drawback is the possible initiation of damage (cracks) in the inner buckling zone because of high local stresses and strains. In this paper, a method to avoid the formation of cracks is introduced. Before forming the bulge the tube is locally heated by an induction coil. For the construction steel (E235+N) a maximum temperature of 700 °C was used to avoid phase transformation. For the numerical study of the process the mechanical properties of the tube material were examined at different temperatures and strain rates to determine its flow curves. A parametrical FE model was developed to simulate the bulging process with local heating. Experiments with local heating were executed and metallographic studies of the bulging area were conducted. While specimens heated to 500 °C showed small cracks left, damage-free flanges could be created at 600 and 700 °C. Static testing of damage-free bulges showed improvements in tensile strength and torsion strength compared to bulges formed at room-temperature, while bending and compression behavior remained nearly unchanged. In cyclic testing the locally heated specimens underwent about 3.7 times as many cycles before failure as the specimens formed at room temperature.

  9. Joining three car body steel sheets by clinching method

    Science.gov (United States)

    Kaščák, Ľuboš; Spišák, Emil; Majerníková, Jana

    2016-12-01

    The optimization of a car body in terms of cost can be achieved by using different materials in various positions of the car in order to utilize specific properties of each different material. Resistance spot welding is the most used method of joining in car body production, but it is not always easy or even possible to join some combination of materials by this method. Clinching is an alternative method to spot welding, as a combination of drawing and forming. The research is focused on the evaluation of clinched joints' properties using shearing test and metallographic observation of material structure.

  10. Diffusion bonding as joining technique for fusion reactor components

    Energy Technology Data Exchange (ETDEWEB)

    Ceccotti, G.C.; Magnoli, L.

    1992-11-01

    The development of joining techniques for fusion reactor divertors has been undertaken at ENEA (Italian Agency for Energy, New Technologies and the Environment) IFEC Saluggia. Joints were made by the diffusion bonding technique between graphite composite material with DS copper and with molybdenum TZM alloy, respectively. The inter-layers, when necessary, were obtained by metallization with an electronic gun. The same technique is employed in joining Be/SS, DS copper/Be, TZM/Be and graphite/Be for the first wall or plasma facing components of fusion reactors. In this case, a suitable inter-layer material can avoid the problems occuring with the more traditional brazing processes.

  11. Superplasticity and joining of zirconia-based ceramics

    International Nuclear Information System (INIS)

    Dominguez-Rodriguez, A.; Gutierrez-Mora, F.; Jimenez-Melendo, M.; Chaim, R.; Routbort, J. L.

    1999-01-01

    Steady-state creep and joining of alumina/zirconia composites containing alumina volume fractions of 20, 60, and 85% have been investigated between 1,250 and 1,350 C. Superplasticity of these compounds is controlled by grain-boundary sliding and the creep rate is a function of alumina volume fraction, not grain size. Using the principles of superplasticity, pieces of the composite have been joined by applying the stress required to achieve 5 to 10% strain to form a strong interface at temperatures as low as 1,200 C

  12. Superplasticity and joining of zirconia-based ceramics

    International Nuclear Information System (INIS)

    Gutierrez-Mora, F.; Dominguez-Rodriguez, A.; Jimenez-Melendo, M.; Chaim, R.; Ravi, G.B.; Routbort, J.L.

    2000-01-01

    Steady-state creep and joining of alumina/zirconia composites containing alumina volume fractions of 20, 60 and 85% have been investigated between 1,250 and 1,350 C. Superplasticity of these compounds is controlled by grain-boundary sliding and the creep rate is a function of alumina volume fraction, not grain size. Using the principles of superplasticity, pieces of the composite have been joined by applying the stress required to achieve 5 to 10% strain to form a strong interface at temperatures as low as 1,200 C

  13. Superplasticity and joining of zirconia-based ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Dominguez-Rodriguez, A.; Gutierrez-Mora, F.; Jimenez-Melendo, M.; Chaim, R.; Routbort, J. L.

    1999-12-10

    Steady-state creep and joining of alumina/zirconia composites containing alumina volume fractions of 20, 60, and 85% have been investigated between 1,250 and 1,350 C. Superplasticity of these compounds is controlled by grain-boundary sliding and the creep rate is a function of alumina volume fraction, not grain size. Using the principles of superplasticity, pieces of the composite have been joined by applying the stress required to achieve 5 to 10% strain to form a strong interface at temperatures as low as 1,200 C.

  14. Regulatory behavior and frontal activity: Considering the role of revised-BIS in relative right frontal asymmetry.

    Science.gov (United States)

    Gable, Philip A; Neal, Lauren B; Threadgill, A Hunter

    2018-01-01

    Essential to human behavior are three core personality systems: approach, avoidance, and a regulatory system governing the two motivational systems. Decades of research has linked approach motivation with greater relative left frontal-cortical asymmetry. Other research has linked avoidance motivation with greater relative right frontal-cortical asymmetry. However, past work linking withdrawal motivation with greater relative right frontal asymmetry has been mixed. The current article reviews evidence suggesting that activation of the regulatory system (revised Behavioral Inhibition System [r-BIS]) may be more strongly related to greater relative right frontal asymmetry than withdrawal motivation. Specifically, research suggests that greater activation of the r-BIS is associated with greater relative right frontal activity, and reduced r-BIS activation is associated with reduced right frontal activity (greater relative left frontal activity). We review evidence examining trait and state frontal activity using EEG, source localization, lesion studies, neuronal stimulation, and fMRI supporting the idea that r-BIS may be the core personality system related to greater relative right frontal activity. In addition, the current review seeks to disentangle avoidance motivation and r-BIS as substrates of relative right frontal asymmetry. © 2017 Society for Psychophysiological Research.

  15. Auditory aura in frontal opercular epilepsy: sounds from afar.

    Science.gov (United States)

    Thompson, Stephen A; Alexopoulos, Andreas; Bingaman, William; Gonzalez-Martinez, Jorge; Bulacio, Juan; Nair, Dileep; So, Norman K

    2015-06-01

    Auditory auras are typically considered to localize to the temporal neocortex. Herein, we present two cases of frontal operculum/perisylvian epilepsy with auditory auras. Following a non-invasive evaluation, including ictal SPECT and magnetoencephalography, implicating the frontal operculum, these cases were evaluated with invasive monitoring, using stereoelectroencephalography and subdural (plus depth) electrodes, respectively. Spontaneous and electrically-induced seizures showed an ictal onset involving the frontal operculum in both cases. A typical auditory aura was triggered by stimulation of the frontal operculum in one. Resection of the frontal operculum and subjacent insula rendered one case seizure- (and aura-) free. From a hodological (network) perspective, we discuss these findings with consideration of the perisylvian and insular network(s) interconnecting the frontal and temporal lobes, and revisit the non-invasive data, specifically that of ictal SPECT.

  16. [Determining the car driver's position at the moment of the frontal crash with a moving KAMAZ truck].

    Science.gov (United States)

    Gusarov, A A; Fetisov, V A; Smirenin, S A

    2016-01-01

    This article is designed to report the results of the comprehensive forensic medical and autotechnical expertise for determining the positions of the driver and the first seat passenger of the GAS-3110 car at the moment of the frontal crash with a KAMAZ-5312 truck. The comparative analysis of the injuries in two subjects one of whom died as a result of the given accident made it possible to conclude that he had occupied the driver's seat in the car. The differential diagnosis was based on the peculiarities of the injuries to the upper extremities with the predominance of the most severe wounds at the right side of the body. Also taken into consideration were the specific conditions of the given frontal collision, design of the GAS-3110 passenger compartment, winter season, night time, and possible neglect of the passive safety means, etc.

  17. Pott's Puffy Tumor Arising from Frontal Sinusitis

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Ji Yeon; Kang, Hyun Koo [Seoul Veterans Hospital, Seoul (Korea, Republic of)

    2010-02-15

    Pott's puffy tumor is an extremely rare and potentially life-threatening complication of frontal sinusitis. We report a case of a 64-year-old man who presented at our emergency department with mild tenderness on the glabellar area and diplopia. Computed Tomography (CT) revealed frontal sinusitis and osteomyelitis of the frontal bone. Following sinus trephination and long-term antibiotic therapy, the patient achieved a complete recovery.

  18. A Novel Control Algorithm for Integration of Active and Passive Vehicle Safety Systems in Frontal Collisions

    Directory of Open Access Journals (Sweden)

    Daniel Wallner

    2010-10-01

    Full Text Available The present paper investigates an approach to integrate active and passive safety systems of passenger cars. Worldwide, the introduction of Integrated Safety Systems and Advanced Driver Assistance Systems (ADAS is considered to continue the today

  19. Finite element analysis of head and brain during frontal impact collisions

    OpenAIRE

    Agh, Nima

    2014-01-01

    Master of Science in Mechanical Engineering. Thesis (M.S.)--Eastern Mediterranean University, Faculty of Engineering, Dept. of Mechanical Engineering, 2014. Supervisor: Assist. Prof. Dr. Neriman Özada.

  20. Frontal Lobe Function in Chess Players

    Directory of Open Access Journals (Sweden)

    Vahid Nejati

    2012-05-01

    Full Text Available Chess is considered as a cognitive game because of severe engagement of the mental resources during playing. The purpose of this study is evaluation of frontal lobe function of chess players with matched non-players. Wisconsin Card Sorting Test (WCST data showed no difference between the player and non-player groups in preservation error and completed categories but surprisingly showed significantly lower grade of the player group in correct response. Our data reveal that chess players dont have any preference in any stage of Stroop test. Chess players dont have any preference in selective attention, inhibition and executive cognitive function. Chess players' have lower shifting abilities than non-players.

  1. Oracle joins CERN Openlab to advance grid computing

    CERN Multimedia

    2003-01-01

    "CERN and Oracle Corporation today announced that Oracle is joining the CERN openlab for DataGrid applications to collaborate in creating new grid computing technologies and exploring new computing and data management solutions far beyond today's Internet-based computing" (1 page).

  2. Youth in the Netherlands Study (JOiN): Study design

    NARCIS (Netherlands)

    A.C. Huizink (Anja); K. Greaves-Lord (Kirstin); B.E. Evans (Brittany); A.S. Euser (Anja); J. van der Ende (Jan); F.C. Verhulst (Frank); I.H.A. Franken (Ingmar)

    2012-01-01

    textabstractBackground: Adolescence is a critical developmental period regarding exposure to substances. Therefore, it is important to be able to identify those adolescents who are most vulnerable to substance abuse in the (near) future. The JOiN study was specifically designed to examine two

  3. Joining of beryllium by braze welding technique: preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Banaim, P.; Abramov, E. [Ben-Gurion Univ. of the Negev, Beersheba (Israel); Zalkind, S.; Eden, S.

    1998-01-01

    Within the framework of some applications, there is a need to join beryllium parts to each other. Gas Tungsten Arc Braze Welds were made in beryllium using 0.3 mm commercially Aluminum (1100) shim preplaced at the joint. The welds exhibited a tendency to form microcracks in the Fusion Zone and Heat Affected Zone. All the microcracks were backfilled with Aluminum. (author)

  4. Inference of Large Phylogenies Using Neighbour-Joining

    DEFF Research Database (Denmark)

    Simonsen, Martin; Mailund, Thomas; Pedersen, Christian Nørgaard Storm

    2011-01-01

    The neighbour-joining method is a widely used method for phylogenetic reconstruction which scales to thousands of taxa. However, advances in sequencing technology have made data sets with more than 10,000 related taxa widely available. Inference of such large phylogenies takes hours or days using...

  5. Advanced manufacturing technologies modern machining, advanced joining, sustainable manufacturing

    CERN Document Server

    2017-01-01

    This book provides details and collective information on working principle, process mechanism, salient features, and unique applications of various advanced manufacturing techniques and processes belong. The book is divided in three sessions covering modern machining methods, advanced repair and joining techniques and, finally, sustainable manufacturing. The latest trends and research aspects of those fields are highlighted.

  6. Accelerating foreign-key joins using asymmetric memory channels

    NARCIS (Netherlands)

    Pirk, H.; Manegold, S.; Kersten, M.

    2011-01-01

    Indexed Foreign-Key Joins expose a very asymmetric access pattern: the Foreign-Key Index is sequentially scanned whilst the Primary-Key table is target of many quasi-random lookups which is the dominant cost factor. To reduce the costs of the random lookups the fact-table can be (re-) partitioned at

  7. Joining the un global compact in spain : an institutional Aproach

    Directory of Open Access Journals (Sweden)

    Ainhoa garayar erro

    2012-07-01

    On the other hand, it can be asserted that the respondent organisations do not perceive major threats from the institutional environment that might undermine the legitimacy gained by joining the GC. Nonetheless, the Spanish organisations participating in the GC highlight the fact that the main institutional factor that might undermine the organization's legitimacy is weak governance and corruption.

  8. Joining of β-SiC by spark plasma sintering

    Czech Academy of Sciences Publication Activity Database

    Grasso, S.; Tatarko, Peter; Rizzo, S.; Porwal, H.; Hu, Ch.; Katoh, Y.; Salvo, M.; Reece, M. J.; Ferraris, M.

    2014-01-01

    Roč. 34, č. 7 (2014), s. 1681-1686 ISSN 0955-2219 EU Projects: European Commission(XE) 264526 - GLACERCO Institutional support: RVO:68081723 Keywords : β-SiC * joining * Spark plasma sintering Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 2.947, year: 2014

  9. Simulation and analysis of microwave heating while joining bulk ...

    African Journals Online (AJOL)

    ATHARVA

    As energy is transferred using electromagnetic waves, a new temperature profile exists for microwave processing due to the ability to penetrate inner ..... research interests include Supply Chain Management (SCM), Advanced Manufacturing Processes; Microwave Joining of Metals, Metal Casting; Industrial. Engineering ...

  10. Improved Joining of Metal Components to Composite Structures

    Science.gov (United States)

    Semmes, Edmund

    2009-01-01

    Systems requirements for complex spacecraft drive design requirements that lead to structures, components, and/or enclosures of a multi-material and multifunctional design. The varying physical properties of aluminum, tungsten, Invar, or other high-grade aerospace metals when utilized in conjunction with lightweight composites multiply system level solutions. These multi-material designs are largely dependent upon effective joining techAn improved method of joining metal components to matrix/fiber composite material structures has been invented. The method is particularly applicable to equipping such thin-wall polymer-matrix composite (PMC) structures as tanks with flanges, ceramic matrix composite (CMC) liners for high heat engine nozzles, and other metallic-to-composite attachments. The method is oriented toward new architectures and distributing mechanical loads as widely as possible in the vicinities of attachment locations to prevent excessive concentrations of stresses that could give rise to delaminations, debonds, leaks, and other failures. The method in its most basic form can be summarized as follows: A metal component is to be joined to a designated attachment area on a composite-material structure. In preparation for joining, the metal component is fabricated to include multiple studs projecting from the aforementioned face. Also in preparation for joining, holes just wide enough to accept the studs are molded into, drilled, or otherwise formed in the corresponding locations in the designated attachment area of the uncured ("wet') composite structure. The metal component is brought together with the uncured composite structure so that the studs become firmly seated in the holes, thereby causing the composite material to become intertwined with the metal component in the joining area. Alternately, it is proposed to utilize other mechanical attachment schemes whereby the uncured composite and metallic parts are joined with "z-direction" fasteners. The

  11. Electron-molecule collisions

    CERN Document Server

    Takayanagi, Kazuo

    1984-01-01

    Scattering phenomena play an important role in modern physics. Many significant discoveries have been made through collision experiments. Amongst diverse kinds of collision systems, this book sheds light on the collision of an electron with a molecule. The electron-molecule collision provides a basic scattering problem. It is scattering by a nonspherical, multicentered composite particle with its centers having degrees of freedom of motion. The molecule can even disintegrate, Le., dissociate or ionize into fragments, some or all of which may also be molecules. Although it is a difficult problem, the recent theoretical, experimental, and computational progress has been so significant as to warrant publication of a book that specializes in this field. The progress owes partly to technical develop­ ments in measurements and computations. No less important has been the great and continuing stimulus from such fields of application as astrophysics, the physics of the earth's upper atmosphere, laser physics, radiat...

  12. Mechanics of train collision

    Science.gov (United States)

    1976-04-30

    A simple and a more detailed mathematical model for the simulation of train collisions are presented. The study presents considerable insight as to the causes and consequences of train motions on impact. Comparison of model predictions with two full ...

  13. The Human Frontal Lobes and Frontal Network Systems: An Evolutionary, Clinical, and Treatment Perspective

    Science.gov (United States)

    Hoffmann, Michael

    2013-01-01

    Frontal lobe syndromes, better termed as frontal network systems, are relatively unique in that they may manifest from almost any brain region, due to their widespread connectivity. The understandings of the manifold expressions seen clinically are helped by considering evolutionary origins, the contribution of the state-dependent ascending monoaminergic neurotransmitter systems, and cerebral connectivity. Hence, the so-called networktopathies may be a better term for the syndromes encountered clinically. An increasing array of metric tests are becoming available that complement that long standing history of qualitative bedside assessments pioneered by Alexander Luria, for example. An understanding of the vast panoply of frontal systems' syndromes has been pivotal in understanding and diagnosing the most common dementia syndrome under the age of 60, for example, frontotemporal lobe degeneration. New treatment options are also progressively becoming available, with recent evidence of dopaminergic augmentation, for example, being helpful in traumatic brain injury. The latter include not only psychopharmacological options but also device-based therapies including mirror visual feedback therapy. PMID:23577266

  14. Photon-photon collisions

    International Nuclear Information System (INIS)

    Haissinski, J.

    1986-06-01

    The discussions presented in this paper deal with the following points: distinctive features of gamma-gamma collisions; related processes; photon-photon elastic scattering in the continuum and γγ →gg; total cross section; γγ → V 1 V 2 (V=vector meson); radiative width measurements and light meson spectroscopy; exclusive channels at large /t/; jets and inclusive particle distribution in γγ collisions; and, the photon structure function F γ 2

  15. Photon-photon collisions

    International Nuclear Information System (INIS)

    Burke, D.L.

    1982-10-01

    Studies of photon-photon collisions are reviewed with particular emphasis on new results reported to this conference. These include results on light meson spectroscopy and deep inelastic e#betta# scattering. Considerable work has now been accumulated on resonance production by #betta##betta# collisions. Preliminary high statistics studies of the photon structure function F 2 /sup #betta#/(x,Q 2 ) are given and comments are made on the problems that remain to be solved

  16. An orbital fistula complicating anaerobic frontal sinusitis and osteomyelitis

    NARCIS (Netherlands)

    H.J. Simonsz (Huib); H.J.F. Peeters; G.M. Bleeker

    1982-01-01

    textabstractA patient is described with an orbital fistula complicating frontal sinusitis and osteomyelitis of the frontal bone. The fistula was excised, but a fortnight later an acute exacerbation occurred. From the discharging pus a Staphylococcus aureus was cultured and from mucosa obtained

  17. Obsessive-compulsive disorder and ventromedial frontal lesions

    DEFF Research Database (Denmark)

    Irle, E; Exner, C; Thielen, K

    1998-01-01

    on the Wisconsin Card Sorting Test. Subjects with lesions of the dorsolateral frontal convexity also showed memory problems, attentional slowing, and lower performance IQ. CONCLUSIONS: Restricted ventromedial frontal leukotomy should be discussed as a last-resort treatment for severe and refractory OCD...

  18. Case Report: Frontal lobe tuberculoma: A clinical and imaging ...

    African Journals Online (AJOL)

    Background: Pediatric nervous system tuberculomas are usually infra-tentorial and multiple. A frontal lobe location is rare. Case Details: We report a 10 year-old boy who presented with a chronic headache and episodes of loss of consciousness. He had no signs of primary pulmonary tuberculosis and a diagnosis of frontal ...

  19. Post-Traumatic Pneumocele of the Frontal Sinus

    Energy Technology Data Exchange (ETDEWEB)

    Karadag, Demet; Calisir, Cuneyt; Adapinar, Baki [Eskisehir Osmangazi University, Eskisehir (Turkmenistan)

    2008-08-15

    A pneumocele is an abnormal dilatation of a paranasal sinus, most commonly affecting the frontal sinus. Although the etiology of pneumocele is not entirely known, several causative factors have been suggested including trauma, surgery, tumor and infection. We report here a case of post-traumatic pneumocele of the frontal sinus following a head trauma.

  20. Minimally invasive approach for lesions involving the frontal sinus ...

    African Journals Online (AJOL)

    Background: Traditional open surgery for frontal sinus pathology and cerebrospinal fluid (CSF) leaks is complex and involves a craniotomy. Minimally invasive options offer an alternate solution. We describe and assess the outcome of a minimally invasive approach for lesions and defects involving the frontal sinus.

  1. Non-frontal Model Based Approach to Forensic Face Recognition

    NARCIS (Netherlands)

    Dutta, A.; Veldhuis, Raymond N.J.; Spreeuwers, Lieuwe Jan

    2012-01-01

    In this paper, we propose a non-frontal model based approach which ensures that a face recognition system always gets to compare images having similar view (or pose). This requires a virtual suspect reference set that consists of non-frontal suspect images having pose similar to the surveillance

  2. Trauma of the Frontal Region Is Influenced by the Volume of Frontal Sinuses. A Finite Element Study

    Directory of Open Access Journals (Sweden)

    Srbislav S. Pajic

    2017-07-01

    Full Text Available Anatomy of frontal sinuses varies individually, from differences in volume and shape to a rare case when the sinuses are absent. However, there are scarce data related to influence of these variations on impact generated fracture pattern. Therefore, the aim of this study was to analyse the influence of frontal sinus volume on the stress distribution and fracture pattern in the frontal region. The study included four representative Finite Element models of the skull. Reference model was built on the basis of computed tomography scans of a human head with normally developed frontal sinuses. By modifying the reference model, three additional models were generated: a model without sinuses, with hypoplasic, and with hyperplasic sinuses. A 7.7 kN force was applied perpendicularly to the forehead of each model, in order to simulate a frontal impact. The results demonstrated that the distribution of impact stress in frontal region depends on the frontal sinus volume. The anterior sinus wall showed the highest fragility in case with hyperplasic sinuses, whereas posterior wall/inner plate showed more fragility in cases with hypoplasic and undeveloped sinuses. Well-developed frontal sinuses might, through absorption of the impact energy by anterior wall, protect the posterior wall and intracranial contents.

  3. Frontal Brain Asymmetry and Willingness to Pay

    Directory of Open Access Journals (Sweden)

    Thomas Z. Ramsøy

    2018-03-01

    Full Text Available Consumers frequently make decisions about how much they are willing to pay (WTP for specific products and services, but little is known about the neural mechanisms underlying such calculations. In this study, we were interested in testing whether specific brain activation—the asymmetry in engagement of the prefrontal cortex—would be related to consumer choice. Subjects saw products and subsequently decided how much they were willing to pay for each product, while undergoing neuroimaging using electroencephalography. Our results demonstrate that prefrontal asymmetry in the gamma frequency band, and a trend in the beta frequency band that was recorded during product viewing was significantly related to subsequent WTP responses. Frontal asymmetry in the alpha band was not related to WTP decisions. Besides suggesting separate neuropsychological mechanisms of consumer choice, we find that one specific measure—the prefrontal gamma asymmetry—was most strongly related to WTP responses, and was most coupled to the actual decision phase. These findings are discussed in light of the psychology of WTP calculations, and in relation to the recent emergence of consumer neuroscience and neuromarketing.

  4. Frontal Brain Asymmetry and Willingness to Pay.

    Science.gov (United States)

    Ramsøy, Thomas Z; Skov, Martin; Christensen, Maiken K; Stahlhut, Carsten

    2018-01-01

    Consumers frequently make decisions about how much they are willing to pay (WTP) for specific products and services, but little is known about the neural mechanisms underlying such calculations. In this study, we were interested in testing whether specific brain activation-the asymmetry in engagement of the prefrontal cortex-would be related to consumer choice. Subjects saw products and subsequently decided how much they were willing to pay for each product, while undergoing neuroimaging using electroencephalography. Our results demonstrate that prefrontal asymmetry in the gamma frequency band, and a trend in the beta frequency band that was recorded during product viewing was significantly related to subsequent WTP responses. Frontal asymmetry in the alpha band was not related to WTP decisions. Besides suggesting separate neuropsychological mechanisms of consumer choice, we find that one specific measure-the prefrontal gamma asymmetry-was most strongly related to WTP responses, and was most coupled to the actual decision phase. These findings are discussed in light of the psychology of WTP calculations, and in relation to the recent emergence of consumer neuroscience and neuromarketing.

  5. Wheelchair caster loading during frontal impact.

    Science.gov (United States)

    Bertocci, Gina E; van Roosmalen, Linda

    2003-01-01

    Many wheelchair users are required or choose to use their wheelchairs as a motor vehicle seat during transport. It is therefore key that the wheelchair components be designed to tolerate crash-level loading conditions. Casters are particularly prone to failure under crash loading conditions. Our study evaluated wheelchair caster loading during 20g/48 kph frontal sled impact testing using an 85-kg surrogate wheelchair base (SWCB) with casters positioned on a load-measuring platform. A Hybrid III 50th percentile male test dummy was seated in the SWCB, which simulated a power wheelchair and was secured using four-point tiedowns. Various rear securement point heights and wheelchair seating systems were used to study their effect on caster loading. Caster normal loading was found to vary from 769 to 7,209 N depending on rear securement location and integrity of the seating system. Dynamic sled impact test results showed that normal loading of the front wheelchair casters was influenced by wheelchair seating system integrity and rear wheelchair securement height. Shear loading varied from 781 to 1,589 N and did not appear to be dependent on seat integrity or rear securement height. The load/time histories measured during dynamic impact testing can be used to guide the development of transit-safe caster design.

  6. Joining dissimilar materials using Friction Stir scribe technique

    Energy Technology Data Exchange (ETDEWEB)

    Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep; Fifield, Leonard S.

    2016-10-03

    The ability to effectively join materials with vastly different melting points like Aluminum-Steel, Polymer composites - metals has been one of the road blocks in realizing multi-material components for light weighting efforts. Friction stir scribe (FSS) technique is a promising method that produces continuous overlap joint between materials with vastly different melting regimes and high temperature flow characteristics. FSS uses an offset cutting tool at the tip of the FSW pin to create an insitu mechanical interlock between material interfaces. With investments from Vehicle Technology office, US DOE and several automotive manufacturers and suppliers PNNL is developing the FSS process and has demonstrated viability of joining several material combinations. Details of welding trails, unique challenges and mitigation strategies in different material combinations will be discussed. Joint characterization including mechanical tests and joint performances will also be presented.

  7. Trend and Development of Semisolid Metal Joining Processing

    Directory of Open Access Journals (Sweden)

    M. N. Mohammed

    2015-01-01

    Full Text Available The semisolid metal joining (SSMJ process or thixojoining process has recently been developed based on the principles of SSM processing, which is a technology that involves the formation of metal alloys between solidus and liquidus temperatures. Thixojoining has many potential benefits, which has encouraged researchers to carry out feasibility studies on various materials that could be utilized in this process and which could transform the production of metal components. This paper reviews the findings in the literature to date in this evolving field, specifically, the experimental details, technology considerations for industrialization, and advantages and disadvantages of the various types of SSMJ methods that have been proposed. It also presents details of the range of materials that have been joined by using the SSMJ process. Furthermore, it highlights the huge potential of this process and future directions for further research.

  8. Breast cancer survivors' decisions to join a dragon boating team.

    Science.gov (United States)

    Weisenbach, Beth B; McDonough, Meghan H

    2014-12-01

    Physical activity is associated with psychosocial and physical health benefits for breast cancer survivors. Little is known, however, about survivors' decision-making processes when considering joining group physical activity programs designed for survivors. Guided by interpretive description methodology (Thorne, 2008), N = 15 breast cancer survivors who were considering or had made the decision to join a dragon boating team were interviewed about their decisions to participate. Four patterns of decision making were identified: searching for a way to care for physical and social needs, taking advantage of opportunities created by breast cancer, dove in with little contemplation, and hesitant to connect with other survivors. Results have implications for understanding decisions to participate in physical activity groups in this population and overcoming challenges to participation.

  9. Thermal and electrical comparison of different joining techniques

    Science.gov (United States)

    Szałapak, J.; Kiełbasiński, K.; Krzemiński, J.; Pawłowski, R.; Jakubowska, M.

    2016-09-01

    After the enforcement of Restriction of Hazardous Substances Directive, one of the biggest problems in electronics is finding a substitution for led solders. Meanwhile, working conditions for the electronics are tougher and tougher - the temperatures the joints have to withstand can be much higher than working temperatures of the soft solders. In current article, the authors present the Low Temperature Joining Technique (LTJT) with the use of pastes based on the mixture of silver nanoparticles and silver microflakes. The authors also show the technology of joining, justify their sintering parameters selection and compare their silver joints with Pb solder and adhesive. The joints prepared with pastes containing silver nanoparticles have much better electrical and thermal properties than the ones made with other techniques.

  10. Collision risk analysis based train collision early warning strategy.

    Science.gov (United States)

    Li, Si-Hui; Cai, Bai-Gen; Liu, Jiang; Wang, Jian

    2018-03-01

    A Train Collision Early Warning System (TCEWS) has been developed for collision avoidance. However, there are few studies regarding how to evaluate the collision risk and provide an early warning concerning a preceding train on the railway. In this paper, we have found that the time for collision avoidance is constrained by the timing of events, such as wireless communication latency, driver reaction, safety protection distance and deceleration rate. Considering these timing components, the time to avoid a collision is calculated accurately. To evaluate the potential collision severity when the following train approaches, the collision risk is defined based on the time to avoid a collision. The train collision early warning signal is divided into a four-tier color-coded system based on the collision risk, with red representing the most severe collision risk, followed by orange, yellow and blue. A field test of the train collision early warning strategy on the Hankou-Yichang Railway is analysed. It is demonstrated that the strategy has sufficient capability to indicate a potential collision and warn the following train. Copyright © 2017. Published by Elsevier Ltd.

  11. Biosynthesis of amidated joining peptide from pro-adrenocorticotropin-endorphin

    Energy Technology Data Exchange (ETDEWEB)

    Cullen, E.I.; Mains, R.E. (Johns Hopkins Univ. School of Medicine, Baltimore, MD (USA))

    1987-09-01

    Joining peptide is the major alpha-amidated product of pro-ACTH/endorphin (PAE) in AtT-20 corticotropic tumor cells. To study intracellular joining peptide synthesis, affinity purified antibodies directed against gamma-MSH, joining peptide, and ACTH were used to immunoprecipitate extracts from biosynthetically labeled AtT-20 cells. Immunoprecipitates were analyzed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and by tryptic peptide mapping on HPLC. In steady labeling experiments, radioactivity in amidated joining peptide (JP) increased roughly linearly with time, in the manner of a final product, whereas radioactivity associated with PAE (1-94)NH2 reached a constant value after 2-4 h, indicating that PAE(1-94)NH2 is an intermediate in the biosynthesis of JP. Radioactivity appeared in ACTH(1-39) well before JP, consistent with a cleavage order in which ACTH is cleaved from PAE(1-95) before JP sequences are cleaved from PAE(1-74). This conclusion was supported by tryptic peptide analyses of immunoprecipitates, which indicated that less than 5% of JP-related material is cleaved from PAE(1-74) before being cleaved from ACTH-related sequences. After a pulse label, radioactivity in PAE(1-94)NH2 reached a peak value after 1 h of chase and declined with a half-life of less than 1 h. Amidated JP increased to a constant level after 2 h of chase. Enough radiolabeled PAE(1-94)NH2 was detected to account for about half of the radioactivity found in amidated JP, indicating that about half of JP-related material is first cleaved from PAE(1-95) before being amidated. This result was corroborated using HPLC purification to determine both amidated and glycine-extended forms of JP.

  12. Reciprocal translocations in Saccharomyces cerevisiae formed by nonhomologous end joining.

    OpenAIRE

    Yu, Xin; Gabriel, Abram

    2004-01-01

    Reciprocal translocations are common in cancer cells, but their creation is poorly understood. We have developed an assay system in Saccharomyces cerevisiae to study reciprocal translocation formation in the absence of homology. We induce two specific double-strand breaks (DSBs) simultaneously on separate chromosomes with HO endonuclease and analyze the subsequent chromosomal rearrangements among surviving cells. Under these conditions, reciprocal translocations via nonhomologous end joining ...

  13. Developments in welding and joining methods of metallic materials

    International Nuclear Information System (INIS)

    Pilarczyk, J.

    2007-01-01

    The impact of the welding technology on the economy development. The welding and joining methods review. The particular role of the laser welding and its interesting applications: with filler metal, twin spot laser welding, hybrid welding process, remote welding. The fiber lasers. The high intensity electron beams applications for surface modification. The TIG welding with the use of the active flux. Friction welding, friction stir welding and friction linear welding. (author)

  14. Meet and join matrices in the poset of exponential divisors

    Indian Academy of Sciences (India)

    ... exponential divisor ( G C E D ) and the least common exponential multiple ( L C E M ) do not always exist. In this paper we embed this poset in a lattice. As an application we study the G C E D and L C E M matrices, analogues of G C D and L C M matrices, which are both special cases of meet and join matrices on lattices.

  15. Ceramic joining through reactive wetting of alumina with calcium ...

    Indian Academy of Sciences (India)

    investigations are carried out in non-oxide ceramics such as AlN, Si3N4, SiC etc while ZrO2 and Al2O3 are the usu- ally considered oxide materials for many applications. The literature about alumina joining is very much limited when compared to other ceramics like Si3N4 and SiC. Alumina, both as single crystal and in ...

  16. International Symposium on Interfacial Joining and Surface Technology (IJST2013)

    Science.gov (United States)

    Takahashi, Yasuo

    2014-08-01

    Interfacial joining (bonding) is a widely accepted welding process and one of the environmentally benign technologies used in industrial production. As the bonding temperature is lower than the melting point of the parent materials, melting of the latter is kept to a minimum. The process can be based on diffusion bonding, pressure welding, friction welding, ultrasonic bonding, or brazing-soldering, all of which offer many advantages over fusion welding. In addition, surface technologies such as surface modification, spraying, coating, plating, and thin-film formation are necessary for advanced manufacturing, fabrication, and electronics packaging. Together, interfacial joining and surface technology (IJST) will continue to be used in various industrial fields because IJST is a very significant form of environmentally conscious materials processing. The international symposium of IJST 2013 was held at Icho Kaikan, Osaka University, Japan from 27-29 November, 2013. A total of 138 participants came from around the world to attend 56 oral presentations and 36 posters presented at the symposium, and to discuss the latest research and developments on interfacial joining and surface technologies. This symposium was also held to commemorate the 30th anniversary of the Technical Commission on Interfacial Joining of the Japan Welding Society. On behalf of the chair of the symposium, it is my great pleasure to present this volume of IOP Conference Series: Materials Science and Engineering (MSE). Among the presentations, 43 papers are published here, and I believe all of the papers have provided the welding community with much useful information. I would like to thank the authors for their enthusiastic and excellent contributions. Finally, I would like to thank all members of the committees, secretariats, participants, and everyone who contributed to this symposium through their support and invaluable effort for the success of IJST 2013. Yasuo Takahashi Chair of IJST 2013

  17. International Symposium on Interfacial Joining and Surface Technology (IJST2013)

    International Nuclear Information System (INIS)

    Takahashi, Yasuo

    2014-01-01

    Interfacial joining (bonding) is a widely accepted welding process and one of the environmentally benign technologies used in industrial production. As the bonding temperature is lower than the melting point of the parent materials, melting of the latter is kept to a minimum. The process can be based on diffusion bonding, pressure welding, friction welding, ultrasonic bonding, or brazing-soldering, all of which offer many advantages over fusion welding. In addition, surface technologies such as surface modification, spraying, coating, plating, and thin-film formation are necessary for advanced manufacturing, fabrication, and electronics packaging. Together, interfacial joining and surface technology (IJST) will continue to be used in various industrial fields because IJST is a very significant form of environmentally conscious materials processing. The international symposium of IJST 2013 was held at Icho Kaikan, Osaka University, Japan from 27–29 November, 2013. A total of 138 participants came from around the world to attend 56 oral presentations and 36 posters presented at the symposium, and to discuss the latest research and developments on interfacial joining and surface technologies. This symposium was also held to commemorate the 30th anniversary of the Technical Commission on Interfacial Joining of the Japan Welding Society. On behalf of the chair of the symposium, it is my great pleasure to present this volume of IOP Conference Series: Materials Science and Engineering (MSE). Among the presentations, 43 papers are published here, and I believe all of the papers have provided the welding community with much useful information. I would like to thank the authors for their enthusiastic and excellent contributions. Finally, I would like to thank all members of the committees, secretariats, participants, and everyone who contributed to this symposium through their support and invaluable effort for the success of IJST 2013. Yasuo Takahashi Chair of IJST 2013

  18. Joining Networks in the World of Open Science

    Directory of Open Access Journals (Sweden)

    Riitta Liisa Maijala

    2016-12-01

    Full Text Available Whereas the first digital revolution of science by digitisation changed the scientific practices of data collection, analysis and reporting of results, the second digital revolution, i.e. open science, will also challenge the current roles of researchers, research organisations, libraries and publishers. From the early days of development, research libraries have joined different networks and been among the most active stakeholders working towards open science. Cohesive networks are needed for coordinated actions and support, whereas bridging networks can provide new approaches and novel information. The Finnish Open Science and Research Initiative is presented in this paper as an example of joining networks, motivating individuals and organisations to deliver high-quality services, infrastructures and competence building to promote a transition towards open science. This paper also presents milestones such as the publication of the academic publishing costs of Finnish research organisations and the maturity level of open science operating cultures in HEIs. Based on the experience of the Finnish open science initiative, joining different networks at the national level on an open mode of operation can significantly speed up the transition towards the era of open science.

  19. Cirurgia de osteoma de seio frontal Surgery of frontal sinus osteoma

    Directory of Open Access Journals (Sweden)

    Lisete Pessoa de Oliveira Fobe

    2002-03-01

    Full Text Available Os osteomas do seio frontal correspondem a 57% dos osteomas dos seios paranasais, com incidência variando de 0,01% a 3%. A remoção cirúrgica nos osteomas frontais é indicada nos pacientes sintomáticos. Nos pacientes assintomáticos pode-se adotar a conduta conservadora ou cirúrgica em todos os pacientes independente da sua localização ou extensão. Cinco pacientes com diagnóstico de osteoma de seio frontal foram operados entre 1995 e 1999. A idade média foi 38,4 anos (extremos de 12 a 55 anos, sendo 3 homens e 2 mulheres. O período de sintomatologia variou de 6 meses a 3 anos com média de 10,5 meses. Quatro pacientes apresentaram cefaléia. Um paciente apresentou epistaxe. Os exames complementares realizados foram: radiografia simples e tomografia computadorizada de seios paranasais com cortes axiais e coronais. Em dois pacientes o diâmetro do osteoma foi maior que 3 cm, e menor que 3 cm em três. A decisão da técnica cirúrgica entre coronal e supraciliar foi estética, reservando-se a abordagem supraciliar para um paciente com calvície, apesar do tumor ser volumoso com extensão para seio etmoidal. Nenhuma dificuldade técnica intra-operatória foi atribuída à escolha da abordagem. O óstio nasofrontal não foi obstruído no intra-operatório. O seguimento pós-operatório mínimo foi de dois anos. Em todos os casos a remoção foi total sem recidiva ou resíduos tumorais. Os sintomas clínicos, achados radiológicos e abordagens cirúrgicas são discutidos. Não ocorreram complicações pós-operatórias.Frontal sinus osteomas are 57% of all paranasal sinus osteomas, with an incidence of 00.1 to 3%. Surgical removal of the frontal sinus osteomas is done in symptomatic patients. Asymptomatic patients can be managed conservatively or submitted to surgery in spite of its location or extension. Five patients having the diagnosis of frontal sinus osteoma were operated on between 1995 and 1999. Medium age was 38.4 years (from 12

  20. Section of Atomic Collisions

    International Nuclear Information System (INIS)

    Berenyi, D.; Biri, S.; Gulyas, L.; Juhasz, Z.; Kover, A.; Orban, A.; Palinkas, J.; Papp, T.; Racz, R.; Ricz, S.

    2009-01-01

    The Section of Atomic Collisions is a research unit with extended activity in the field of atomic and molecular physics. Starting from the study of atomic processes at the beamlines of nuclear physics accelerators in the seventies, our research community became one of the centers of fundamental research in Atomki. We also have a strong connection to materials sciences especially along the line of electron and ion spectroscopy methods. Our present activity covers a wide range of topics from atomic collision mechanisms of fundamental interest, to the complex interactions of electrons, ions, photons and antiparticles with atoms, molecules, surfaces, and specific nanostructures. In the last few years, an increasing fraction of our present topics has become relevant for applications, e.g., molecular collision studies for the radiation therapy methods of tumors, or ion-nanostructure interactions for the future construction of small ion-focusing elements. Our section belongs to the Division of Atomic Physics. The other unit of the Division is the Section of Electron Spectroscopy and Materials Sciences. There are traditionally good connections and a strong collaboration between the groups of the two sections in many fields. From the very beginning of our research work in atomic collisions, external collaborations were of vital importance for us. We regularly organize international workshops in the field of fast ion-atom collisions and related small conferences in Debrecen from 1981. Recently, we organized the Conference on Radiation Damage in Biomolecular Systems (RADAM 2008, Debrecen), and coorganized the Conference on Elementary Processes in Atomic Systems (CEPAS 2008, Cluj). We have access to several large scale facilities in Europe within the framework of formal and informal collaborations. The next themes are in this article: Forward electron emission from energetic atomic collisions; Positron-atom collisions; Photon-atom interactions; Interference effects in electron

  1. [Intracranial collision tumor--A case report (author's transl)].

    Science.gov (United States)

    Fukaya, T; Yoshida, J; Banno, T; Kageyama, N; Ito, M

    1976-06-01

    A 21-year-old man with nasopharyngeal tumor was first admitted to the Nagoya University Hospital on April 15, 1972. He had difficulty in speaking and swallowing, and developed double vision prior to admission. A soft and yellow tumor was found in the nasopharynx and revealed typical features of chordoma. The patient underwent Co60 irradiation after the operation. On January 25, 1973, the patient developed double vision of severe degree. Microscopic examination of the specimen which was obtained at the time of the second operation in February 9, 1973, disclosed a coexistence (collision) of chordoma and hemangioblastoma. The two different tumors were situated in juxtaposition on histological examination. Co60 irradiation was added during his second hospitalization. Three months after the second operation, he developed symptoms of meningitis and was hospitalized for the third time on June 3, 1973, at which time the tumor tissue extended through the right frontal and middle fossa. The third operation was done with frontal craniotomy and tumor was partially removed. The histological diagnosis was hemangioblastoma. Postoperatively the patient went downhill and died on September 19, 1973. The report of a collision tumor of intracranial chordoma and hemangioblastoma is not found in the previous literature. There have been many theories as to the origin of collision tumor. Some investigators have proposed that the existence of hyperplastic blood vessels within the glioblastoma is responsible for the collision tumor of sarcoma and glioblastoma. Since the advent of radiotherapy, several examples of sarcoma have been discovered at postmortem examination in patient irradiated for treatment of cerebral neoplasm, both gliogeneous and nongliogenous, suggesting a possible relationship between the tumor and the radiation therapy. In our case, the chordoma showed neither hyperplastic blood vessels nor malignant pattern on histological examination. It was suspected that post

  2. Frontal Dynamics of Powder Snow Avalanches

    Science.gov (United States)

    Louge, M. Y.; Carroll, C. S.; Turnbull, B.

    2012-04-01

    We model the dynamics of the head of dilute powder snow avalanches sustained by a massive frontal blow-out, arising as a weakly cohesive snow cover is fluidized by the very pore pressure gradients that the avalanche induces within the snow pack. Such material eruption just behind the front acts as a source of denser fluid thrust into a uniform ambient air flow at high Reynolds number. In such "eruption current", fluidization depth is inversely proportional to a bulk Richardson number representing avalanche height. By excluding situations in which the snow cover is not fluidized up to its free surface, we derive a criterion combining snow pack friction and density indicating which avalanches can produce a sustainable powder cloud. A mass balance involving snow cover and powder cloud sets avalanche height and mean density. By determining which solution of the mass balance is stable, we find that avalanches reach constant growth and acceleration rates for fixed slope and avalanche width. Under these conditions, we calculate the fraction of the fluidized cover that is actually scoured and blown-out into the cloud, and deduce from a momentum balance on the head that the avalanche accelerates at a rate only 14% of the gravitational component along the flow. We also calculate how far a powder cloud travels until its mean density becomes constant. Finally, we show that the dynamics of powder snow avalanches are crucially affected by the rate of change of their width, for example by reaching an apparent steady speed as their channel widens. If such widening is rapid, or if slope inclination vanishes, we calculate where and how powder clouds collapse. Predictions agree well with observations of powder snow avalanches carried out at the Vallee de la Sionne (Switzerland).

  3. Alteraciones de memoria en daño cerebral frontal

    OpenAIRE

    Vega Rodríguez, Irene de la; Noreña, David de

    2007-01-01

    El córtex frontal está implicado en importantes procesos de memoria, pero tiene un papel diferente al de las estructuras temporales y diencefálicas mediales. Mientras que el daño en estas estructuras produce una grave amnesia anterógrada, en el daño frontal se manifiestan una serie de problemas y distorsiones concretas como las fabulaciones, la amnesia de la fuente, el déficit de memoria prospectiva o las alteraciones en el recuerdo libre. El lóbulo frontal no está implicado en el almacenamie...

  4. About the Collision Repair Campaign

    Science.gov (United States)

    EPA developed the Collision Repair Campaign to focus on meaningful risk reduction in the Collision Repair source sector to complement ongoing community air toxics work and attain reductions at a faster rate.

  5. Method of and apparatus for use in joining tubular components and tube assemblies made thereby

    International Nuclear Information System (INIS)

    Percival, S.R.

    1979-01-01

    A method of joining difficult to weld materials involves the forming of a rolled joint. A particular application is the joining of zirconium alloy calandria tubes to stainless steel tube-plates in a SGHWR. (UK)

  6. Consumers’ Collision Insurance Decisions

    DEFF Research Database (Denmark)

    Austin, Laurel; Fischhoff, Baruch

    Using interviews with 74 drivers, we elicit and analyse how people think about collision coverage and, more generally, about insurance decisions. We compare the judgments and behaviours of these decision makers to the predictions of a range of theoretical models: (a) A model developed by Lee (2007...... a cognitive model based on budgeting. Our findings emphasize the importance of budget constraints, which lead consumers to budget their income across consumption categories. We find also that a simple heuristic accounts for many collision coverage decisions: purchase coverage for cars worth more than some...

  7. Vocal Fold Collision Modeling

    DEFF Research Database (Denmark)

    Granados, Alba; Brunskog, Jonas; Misztal, M. K.

    2015-01-01

    When vocal folds vibrate at normal speaking frequencies, collisions occurs. The numerics and formulations behind a position-based continuum model of contact is an active field of research in the contact mechanics community. In this paper, a frictionless three-dimensional finite element model...... of the vocal fold collision is proposed, which incorporates different procedures used in contact mechanics and mathematical optimization theories. The penalty approach and the Lagrange multiplier method are investigated. The contact force solution obtained by the penalty formulation is highly dependent...

  8. Ice particle collisions

    Science.gov (United States)

    Sampara, Naresh; Turnbull, Barbara; Hill, Richard; Swift, Michael

    2017-04-01

    Granular interactions of ice occur in a range of geophysical, astrophysical and industrial applications. For example, Saturn's Rings are composed of icy particles from micrometers to kilometres in size - inertial and yet too small to interact gravitationally. In clouds, ice crystals are smashed to pieces before they re-aggregate to for snow floccules in a process that is very much open to interpretation. In a granular flow of ice particles, the energy spent in collisions can lead to localized surface changes and wetting, which in turn can promote aggregation. To understand the induced wetting and its effects, we present two novel experimental methods which provide snippets of insight into the collisional behaviour of macroscopic ice particles. Experiment 1: Microgravity experiments provide minute details of the contact between the ice particles during the collision. A diamagnetic levitation technique, as alternative to the parabolic flight or falling tower experiments, was used to understand the collisional behaviour of individual macroscopic icy bodies. A refrigerated cylinder, that can control ambient conditions, was inserted into the bore of an 18 Tesla superconducting magnet and cooled to -10°C. Initial binary collisions were created, where one 4 mm ice particle was levitated in the magnet bore whilst another particle was dropped vertically from the top of the bore. The trajectories of both particles were captured by high speed video to provide the three-dimensional particle velocities and track the collision outcome. Introducing complexity, multiple particles were levitated in the bore and an azimuthal turbulent air flow introduced, allowing the particles to collide with other particles within a coherent fluid structure (mimicking Saturn's rings, or an eddy in a cloud). In these experiments, a sequence of collisions occur, each one different to the previous one due to the changes in surface characteristics created by the collisions themselves. Aggregation

  9. Frontal Lobe Decortication (Frontal Lobectomy with Ventricular Preservation) in Epilepsy-Part 1: Anatomic Landmarks and Surgical Technique.

    Science.gov (United States)

    Wen, Hung Tzu; Da Róz, Leila Maria; Rhoton, Albert L; Castro, Luiz Henrique Martins; Teixeira, Manoel Jacobsen

    2017-02-01

    An extensive frontal resection is a frequently performed neurosurgical procedure, especially for treating brain tumor and refractory epilepsy. However, there is a paucity of reports available regarding its surgical anatomy and technique. We sought to present the anatomic landmarks and surgical technique of the frontal lobe decortication (FLD) in epilepsy. The goals were to maximize the gray matter removal, spare primary and supplementary motor areas, and preserve the frontal horn. The anatomic study was based on dissections performed in 15 formalin-fixed adult cadaveric heads. The clinical experience with 15 patients is summarized. FLD consists of 5 steps: 1) coagulation and section of arterial branches of lateral surface; 2) paramedian subpial resection 3 cm ahead of the precentral sulcus to reach the genu of corpus callosum; 3) resection of gray matter of lateral surface, preserving the frontal horn; 4) removal of gray matter of basal surface preserving olfactory tract; 5) removal of gray matter of the medial surface under the rostrum of corpus callosum. The frontal horn was preserved in all 15 patients; 12 patients (80%) had no complications; 2 patients presented temporary hemiparesis; and 1 Rasmussen syndrome patient developed postoperative fever. The best seizure control was in cases with focal magnetic resonance imaging abnormalities limited to the frontal lobe. FLD is an anatomy-based surgical technique for extensive frontal lobe resection. It presents reliable anatomic landmarks, selective gray matter removal, preservation of frontal horn, and low complication rate in our series. It can be an alternative option to the classical frontal lobectomy. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Stochastic collision and aggregation analysis of kaolinite in water through experiments and the spheropolygon theory.

    Science.gov (United States)

    Tang, Fiona H M; Alonso-Marroquin, Fernando; Maggi, Federico

    2014-04-15

    An approach based on spheropolygons (i.e., the Minkowski sum of a polygon with N vertices and a disk with spheroradius r) is presented to describe the shape of kaolinite aggregates in water and to investigate interparticle collision dynamics. Spheropolygons generated against images of kaolinite aggregates achieved an error between 0.5% and 20% as compared to at least 32% of equivalent spheres. These spheropolygons were used to investigate the probability of collision (Pr[C]) and aggregation (Pr[A]) under the action of gravitational, viscous, contact (visco-elastic), electrostatic and van der Waals forces. In ortho-axial (i.e., frontal) collision, Pr[A] of equivalent spheres was always 1, however, stochastic analysis of collision among spheropolygons showed that Pr[A] decreased asymptotically with N increasing, and decreased further in peri-axial (i.e., tangential) collision. Trajectory analysis showed that not all collisions occurring within the attraction zone of the double layer resulted in aggregation, neither all those occurring outside it led to relative departure. Rather, the relative motion on surface asperities affected the intensity of contact and attractive forces to an extent to substantially control a collision outcome in either instances. Spheropolygons revealed therefore how external shape can influence particle aggregation, and suggested that this is equally important to contact and double layer forces in determining the probability of particle aggregation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Determination of frontal offset test conditions based on crash data

    Science.gov (United States)

    1998-01-01

    This paper reports on the test procedure development : phase of the agencys Improved Frontal Protection : research program. It is anticipated that even after all cars : and light trucks have air bags for drivers and front seat : passengers there w...

  12. Right-frontal cortical asymmetry predicts increased proneness to nostalgia.

    Science.gov (United States)

    Tullett, Alexa M; Wildschut, Tim; Sedikides, Constantine; Inzlicht, Michael

    2015-08-01

    Nostalgia is often triggered by feelings-such as sadness, loneliness, or meaninglessness-that are typically associated with withdrawal motivation. Here, we examined whether a trait tendency to experience withdrawal motivation is associated with nostalgia proneness. Past work indicates that baseline right-frontal cortical asymmetry is a neural correlate of withdrawal-related motivation. We therefore hypothesized that higher baseline levels of right-frontal asymmetry would predict increased proneness to nostalgia. We assessed participants' baseline levels of frontal cortical activity using EEG. Results supported the hypothesis and demonstrated that the association between relative right-frontal asymmetry and increased nostalgia remained significant when controlling for the Big Five personality traits. Overall, these findings indicate that individuals with a stronger dispositional tendency to experience withdrawal-related motivation are more prone to nostalgia. © 2015 Society for Psychophysiological Research.

  13. [Morphometric vectorial method of analysis of the frontal sinuses].

    Science.gov (United States)

    Iordan, A; Ulmeanu, D

    2008-03-01

    The frontal sinuses are pneumatic cavities located in the thickness of the squama frontalis, which communicate with the nasal cavity through the frontonasal duct. These cavities develop by the pneumatisation extent of some anterior ethmoidal cells. Morphologically, there is a large variability of the frontal sinus shape, size and extent, the position of the intersinusal septum, the existence and number of intrasinusal septa. There exist morphologically atypical frontal sinuses as: uni- or bilateral frontal sinuses aplasia, supernumerary sinuses, great extent of the cavities. Paranasal sinuses can be explored by different methods, but the most accessible and easy to perform is conventional radiological imaging. The radiographs can be morphometrically assessed in order to prove the individuality of these air cavities.

  14. Frontal parosteal lipoma with thickening of diploic space

    Directory of Open Access Journals (Sweden)

    Tsuyoshi Morishita

    2015-09-01

    Full Text Available Parosteal lipoma is a rare benign tumor that is composed mainly of benign mature lipocytes, and it has an intimate association with the underlying affected bone. Parosteal lipoma involving the head and neck is very rare, and there are only two reported cases of parosteal lipoma of the skull in English literature. This paper reports a rare case of frontal parosteal lipoma in a young child with a hard enlargement of the forehead region after blunt trauma. Computed tomography revealed a large soft tissue mass and an osseous projection of the unilateral frontal bone. The pathology report identified lipoma and thickening of diploic space of the frontal bone. Here, we present a new case of parosteal lipoma in the frontal region.

  15. Distinct frontal lobe morphology in girls and boys with ADHD

    Directory of Open Access Journals (Sweden)

    Benjamin Dirlikov

    2015-01-01

    Conclusions: These results elucidate sex-based differences in cortical morphology of functional subdivisions of the frontal lobe and provide additional evidence of associations among SA and symptom severity in children with ADHD.

  16. Query optimization through the looking glass, and what we found running the Join Order Benchmark

    NARCIS (Netherlands)

    V. Leis (Viktor); B. Radke (Bernhard); A. Gubichev (Andrey); A. Mirchev (Atanas); P.A. Boncz (Peter); A. Kemper (Alfons); T. Neumann (Thomas)

    2018-01-01

    textabstractFinding a good join order is crucial for query performance. In this paper, we introduce the Join Order Benchmark that works on real-life data riddled with correlations and introduces 113 complex join queries. We experimentally revisit the main components in the classic query optimizer

  17. Giant cell tumor of the frontal sinus: case report

    Energy Technology Data Exchange (ETDEWEB)

    Matushita, Joao Paulo, E-mail: jpauloejulieta@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Hospital das Clinicas; Matushita, Julieta S.; Matushita Junior, Joao Paulo Kawaoka [Centro de Diagnostico por Imagem Dr. Matsushita, Belo Horizonte, MG (Brazil); Matushita, Cristina S. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Hospital Universitario Clementino Fraga Filho; Simoes, Luiz Antonio Monteiro; Carvalho Neto, Lizando Franco de

    2013-06-15

    The authors report the case of a giant cell tumor of the frontal sinus in a 54-year-old male patient. This tumor location is rare, and this is the third case reported in the literature with radiographic documentation and histopathological confirmation. The patient underwent surgery, with curettage of frontal sinus and placement of a prosthesis. He died because a voluntary abrupt discontinuation of corticosteroids. (author)

  18. Frontal Lobe Tuberculoma: A Clinical and Imaging Challenge

    OpenAIRE

    Alemayehu, Tinsae; Ergete, Wondwossen; Abebe, Workeabeba

    2017-01-01

    Background Pediatric nervous system tuberculomas are usually infra-tentorial and multiple. A frontal lobe location is rare. Case Details We report a 10 year-old boy who presented with a chronic headache and episodes of loss of consciousness. He had no signs of primary pulmonary tuberculosis and a diagnosis of frontal tuberculoma was made upon a post-operative biopsy. He improved following treatment with anti-tubercular drugs. Conclusion Tuberculosis should be considered in children with a chr...

  19. Joining silicon nitride to FA-129 iron aluminide

    Science.gov (United States)

    Brochu, Mathieu

    Joints between dissimilar materials are characterized particularly by compositional gradients and microstructural changes, which yield large variations in chemical, physical and mechanical properties across the joint. The joining of dissimilar materials is therefore more complex than the joining of similar materials. In this project, the joining procedure, from the interaction between the different components in a joint to the determination of the mechanical properties was applied to the Si3N4/FA-129 system. This iron aluminide intermetallic alloy (FA-129), was developed by Oak Ridge National Laboratories (ORNL) to have high temperature properties with good room temperature ductility. This intermetallic is replacing high strength ferritic stainless steel (SS) in moderate strength applications due to cost and property reasons. Joints between SS and Si3N4 are already used industrially and this project was to evaluate the potential to replace these Si3N 4/SS joints by those of Si3N4/FA-129. Broadly stated, the results obtained during this project are as follows: (I) The E2 energy for Si3N4 ceramic was calculated to be 3.01 keV. (II) The wetting of iron aluminide alloy by copper has been achieved and the spreading and reaction kinetics are influenced by the presence of Cr as alloying element. (III) The penetration and decohesion of the FA-129 microstructure is significantly reduced by the utilization of a Cu alloy containing a high titanium concentration. (IV) An active brazing alloy containing a high active element content can be fabricated by an electroless deposition technique. (V) The melting behavior of the powder was characterized and complete melting occurs in a multi-step process at different temperatures, which are a function of the heating rate. (VI) The strength of joint produced by brazing Si3N4 to itself using the composite powder reached 400 MPa. (VII) Direct brazing of Si 3N4 to FA-129 was shown to be unsuccessful and therefore a soft Cu interlayer was

  20. Metal-ceramic interfaces: joining silicon nitride-stainless steel

    Science.gov (United States)

    Polanco, R.; De Pablos, A.; Miranzo, P.; Osendi, M. I.

    2004-11-01

    Joining of hot pressed silicon nitride using three types of stainless steel (AISI 304, 316 and 321) as interlayer was done by diffusion bonding at 1100 °C for 120 min. An extensive reaction zone of about 7 μm was formed in the contact region, where Cr2N, FexSiy and α-Fe were observed, outside that region the austenitic phase with precipitates of chromium nitride was observed. In the Mo-containing stainless steel (AISI 316) formation of Mo3Si was also detected. Moderate strengths were measured by shear testing for these joints.

  1. FRESNO State joins exploration of new frontiers in physics

    CERN Multimedia

    2008-01-01

    California State University, Fresno has joined a prestigious collaboration of top physicists, giving the Department of Physics' students, faculty and staff access to the most up-to-date information possible on new frontiers in the science for the next 15 years or longer. The program is the ATLAS (an acronym for A Toroidal LHC ApparatuS) Experiment, which makes use of the Large Hadron Collider (LHC) under construction at the European Organization for Nuclear Research (CERN) near Geneva, Switzerland. (CERN also gave birth to the World Wide Web.)

  2. Symmetric bends how to join two lengths of cord

    CERN Document Server

    Miles, Roger E

    1995-01-01

    A bend is a knot securely joining together two lengths of cord (or string or rope), thereby yielding a single longer length. There are many possible different bends, and a natural question that has probably occurred to many is: "Is there a 'best' bend and, if so, what is it?"Most of the well-known bends happen to be symmetric - that is, the two constituent cords within the bend have the same geometric shape and size, and interrelationship with the other. Such 'symmetric bends' have great beauty, especially when the two cords bear different colours. Moreover, they have the practical advantage o

  3. Decomposing Borel functions using the Shore-Slaman join theorem

    OpenAIRE

    Kihara, Takayuki

    2013-01-01

    Jayne and Rogers proved that every function from an analytic space into a separable metric space is decomposable into countably many continuous functions with closed domains if and only if the preimage of each $F_\\sigma$ set under it is again $F_\\sigma$. Many researchers conjectured that the Jayne-Rogers theorem can be generalized to all finite levels of Borel functions. In this paper, by using the Shore-Slaman join theorem on the Turing degrees, we show the following variant of the Jayne-Rog...

  4. Ultrapulse welding: A new joining technique. [for automotive industry

    Science.gov (United States)

    Anderson, D. G.

    1972-01-01

    The ultrapulse process is a resistance welding process that utilizes unidirectional current of high magnitude for a very short time with a precisely controlled dynamic force pulse. Peak currents of up to 220,000 amperes for two to ten milliseconds are used with synchronized force pulses of up to nine thousand pounds. The welding current passing through the relatively high resistance of the interface between the parts that are being joined results in highly localized heating. Described is the UPW process as it applies to the automotive industry.

  5. Photon-photon collisions

    Energy Technology Data Exchange (ETDEWEB)

    Brodsky, S.J.

    1988-07-01

    Highlights of the VIIIth International Workshop on Photon-Photon Collisions are reviewed. New experimental and theoretical results were reported in virtually every area of ..gamma gamma.. physics, particularly in exotic resonance production and tests of quantum chromodynamics where asymptotic freedom and factorization theorems provide predictions for both inclusive and exclusive ..gamma gamma.. reactions at high momentum transfer. 73 refs., 12 figs.

  6. Protons in collision

    International Nuclear Information System (INIS)

    Albrow, M.

    1983-01-01

    The article is concerned with the Intersecting Storage Rings (ISR), sited at CERN, which produces the world's highest energy collisions between protons, but is due to be dismantled soon. The ISR has contributed to major advances in physics, during the past 13 years, particularly in quantum chromodynamics. (U.K.)

  7. Collision Probability Analysis

    DEFF Research Database (Denmark)

    Hansen, Peter Friis; Pedersen, Preben Terndrup

    1998-01-01

    It is the purpose of this report to apply a rational model for prediction of ship-ship collision probabilities as function of the ship and the crew characteristics and the navigational environment for MS Dextra sailing on a route between Cadiz and the Canary Islands.The most important ship and crew...

  8. High energy nuclear collisions

    Indian Academy of Sciences (India)

    We review some basic concepts of relativistic heavy-ion physics and discuss our understanding of some key results from the experimental program at the relativistic heavy-ion collider (RHIC). We focus in particular on the early time dynamics of nuclear collisions, some result from lattice QCD, hard probes and photons.

  9. CMS SEES FIRST COLLISIONS

    CERN Multimedia

      A very special moment.  On 23rd November, 19:40 we recorded our first collisions with 450GeV beams well centred in CMS.   If you have any comments / suggestions please contact Karl Aaron GILL (Editor)

  10. Collisions in soccer kicking

    DEFF Research Database (Denmark)

    Andersen, Thomas Bull; Dörge, Henrik C.; Thomsen, Franz Ib

    1999-01-01

    An equation to describe the velocity of the soccer ball after the collision with a foot was derived. On the basis of experimental results it was possible to exclude certain factors and only describe the angular momentum of the system, consisting of the shank, the foot and the ball, leading...

  11. Ultrarelativistic oscillon collisions

    NARCIS (Netherlands)

    Amin, M.A.; Banik, I.; Negreanu, C.; Yang, I.S.

    2014-01-01

    In this short paper we investigate the ultrarelativistic collisions of small amplitude oscillons in 1+1 dimensions. Using the amplitude of the oscillons and the inverse relativistic boost factor γ−1 as the perturbation variables, we analytically calculate the leading order spatial and temporal phase

  12. Unfamiliar Face Matching With Frontal and Profile Views.

    Science.gov (United States)

    Kramer, Robin S S; Reynolds, Michael G

    2018-04-01

    Research has systematically examined how laboratory participants and real-world practitioners decide whether two face photographs show the same person or not using frontal images. In contrast, research has not examined face matching using profile images. In Experiment 1, we ask whether matching unfamiliar faces is easier with frontal compared with profile views. Participants completed the original, frontal version of the Glasgow Face Matching Test, and also an adapted version where all face pairs were presented in profile. There was no difference in performance across the two tasks, suggesting that both views were similarly useful for face matching. Experiments 2 and 3 examined whether matching unfamiliar faces is improved when both frontal and profile views are provided. We compared face matching accuracy when both a frontal and a profile image of each face were presented, with accuracy using each view alone. Surprisingly, we found no benefit when both views were presented together in either experiment. Overall, these results suggest that either frontal or profile views provide substantially overlapping information regarding identity or participants are unable to utilise both sources of information when making decisions. Each of these conclusions has important implications for face matching research and real-world identification development.

  13. Athletes in a Slump: Neurophysiological Evidence from Frontal Theta Activity

    Directory of Open Access Journals (Sweden)

    Jingu Kim

    2014-01-01

    Full Text Available The purpose of this study is to investigate the neurophysiological differences in athletes who suffer from a slump and other athletes who do not. Eighteen high school student athletes participated in this experiment. A subjective questionnaire was conducted to identify athletes in a slump (i.e., the slump group and not in a slump (i.e., the no-slump group. EEG data was recorded at 4 regions (left prefrontal, right prefrontal, left frontal, and right frontal. A two-way (2 groups x 4 regions ANOVA was performed on the dependent variable (i.e., frontal theta power. The findings of this study demonstrated that participants in the no-slump group showed higher frontal theta activity than their counterparts in the slump group. From the findings of this study, it is suggested that mental fatigue may cause low frontal theta activity in athletes who experience a slump. The present study makes an important contribution to the current literature by being the first to report that EEG theta power over frontal regions can be used as a marker of athletes suffering from a slump.

  14. Accelerating Select Where And Select Join Queries On A Gpu

    Directory of Open Access Journals (Sweden)

    Marcin Pietron

    2013-01-01

    Full Text Available This paper presents implementations of a few selected SQL operations using theCUDA programming framework on the GPU platform. Nowadays, the GPU’sparallel architectures give a high speed-up on certain problems. Therefore, thenumber of non-graphical problems that can be run and sped-up on the GPUstill increases. Especially, there has been a lot of research in data mining onGPUs. In many cases it proves the advantage of offloading processing fromthe CPU to the GPU. At the beginning of our project we chose the set ofSELECT WHERE and SELECT JOIN instructions as the most common op-erations used in databases. We parallelized these SQL operations using threemain mechanisms in CUDA: thread group hierarchy, shared memories, andbarrier synchronization. Our results show that the implemented highly parallelSELECT WHERE and SELECT JOIN operations on the GPU platform canbe significantly faster than the sequential one in a database system run on theCPU.

  15. Electric Propulsion Concepts for an Inverted Joined Wing Airplane Demonstrator

    Directory of Open Access Journals (Sweden)

    Cezary Galinski

    2017-05-01

    Full Text Available One of the airplane design concepts that potentially allows for significantly increased efficiency, but has not yet been investigated thoroughly, is the inverted joined wing configuration, where the upper wing is positioned in front of the lower one. We performed wind tunnel and flight testing of a demonstrator of this concept, first by applying electrical propulsion to simplify wind tunnel testing, and then the same electrical-propulsion demonstrator performed several flights. As the chosen propulsion method proved to be too cumbersome for an intensive flight campaign and significant loss of battery performance was also observed, the electrical propulsion was then replaced by internal combustion propulsion in the second phase, involving longer-duration flight testing. Next we identified and analyzed two potentially beneficial modifications to the design tested: one involved shifting the center of gravity towards the aft, the other involved modifying the thrust vector position, both with the assumption that electric motors can be applied for propulsion. On this basis, the paper finishes with some conclusions concerning a new concept of electrical propulsion for an inverted joined wing design, combining two ideas: hybridization and distribution along the aft wing leading edge.

  16. Temperature Controlled Laser Joining of Aluminum to Galvanized Steel

    Science.gov (United States)

    Weller, Daniel; Simon, Jörg; Stritt, Peter; Weber, Rudolf; Graf, Thomas; Bezençon, Cyrille; Bassi, Corrado

    Reliable joining of 6000 series aluminum alloy to galvanized steel is a challenge for current manufacturing technologies. To control and limit the formation of brittle intermetallic phases, mixing of both metals in liquid state has to be avoided. It has been shown that laser weld-brazing is a possible process. Thereby the aluminum and zinc layer of the galvanized steel are molten and the steel remains solid during the process. In addition, to avoid zinc degassing, the aluminum melt bath temperature has to be below zinc boiling temperature of 907°C. To meet these requirements a temperature controlled laser process was developed, allowing to join the two materials without flux and filler material. The thickness of the intermetallic layer shows a dependency on the set temperature used to control the process. At optimum set temperature the thickness of intermetallic phases can be limited to about 5 μm. Tensile strengths of the joints of up to 75% of the aluminum base material were achieved.

  17. Advances in appendage joining techniques for PHWR fuel cladding

    International Nuclear Information System (INIS)

    Desai, P.B.; Ray, T.K.; Date, V.G.; Purushotham, D.S.C.

    1995-01-01

    This paper describes work carried out at the BARC on the development of a technique to join tiny appendages (spacers and bearing pads) to thin cladding (before loading of UO 2 pellets) by resistance welding for PHWR fuel assemblies. The work includes qualifying the process for production environment, designing prototype equipment for regular production and quality monitoring. In the first phase of development, welding of appendages on UO 2 loaded elements was successfully developed, and is being used in production. Welding of appendages on to empty clad tubes is a superior technique for several reasons. Many problems associated with development of welding on empty tubes were resolved. work was initiated, in the second phase of the development task, to select a suitable technique to join appendages on empty clad tubes without any collapse of thin clad. Several alternatives were reviewed and assessed such as laser, full face welding, shim welding and shrink fitting ring spacers. Selection of a method using a mandrel and a modified electrode geometry was fully developed. Results were optimized and process development successfully completed. Appropriate weld monitoring techniques were also reviewed for their adaptation. This technique is useful for 19, 22 as well as 37 element assemblies. (author)

  18. Positioning and joining of organic single-crystalline wires

    Science.gov (United States)

    Wu, Yuchen; Feng, Jiangang; Jiang, Xiangyu; Zhang, Zhen; Wang, Xuedong; Su, Bin; Jiang, Lei

    2015-01-01

    Organic single-crystal, one-dimensional materials can effectively carry charges and/or excitons due to their highly ordered molecule packing, minimized defects and eliminated grain boundaries. Controlling the alignment/position of organic single-crystal one-dimensional architectures would allow on-demand photon/electron transport, which is a prerequisite in waveguides and other optoelectronic applications. Here we report a guided physical vapour transport technique to control the growth, alignment and positioning of organic single-crystal wires with the guidance of pillar-structured substrates. Submicrometre-wide, hundreds of micrometres long, highly aligned, organic single-crystal wire arrays are generated. Furthermore, these organic single-crystal wires can be joined within controlled angles by varying the pillar geometries. Owing to the controllable growth of organic single-crystal one-dimensional architectures, we can present proof-of-principle demonstrations utilizing joined wires to allow optical waveguide through small radii of curvature (internal angles of ~90–120°). Our methodology may open a route to control the growth of organic single-crystal one-dimensional materials with potential applications in optoelectronics. PMID:25814032

  19. Welding of gold nanowires with different joining procedures

    International Nuclear Information System (INIS)

    Guo, J. Y.; Xu, C. X.; Hu, A. M.; Shi, Z. L.; Sheng, F. Y.; Dai, J.; Li, Z. H.

    2012-01-01

    Welding of single-crystal metallic nanowires is likely to have an important role in the bottom-up fabrication of nanodevices. The welding effects of free ends of two single-crystal gold nanowires (Au–Au) were demonstrated by Monte Carlo simulations in this paper. The quantum corrected Sutton–Chen type many-body potential was used to model the metal–metal interactions. Metallic nanowires were first placed closely with head-to-head, head-to-side and side-to-side joining procedures. Two ends were successfully welded together to form a continuous nanowire by annealing at different temperatures. The welding effects of the different joining procedure with different temperatures were compared. Structures of the welded specimens were characterized by the common neighbor analysis technique. Variable atomic mobility, freedom and contacting angles may result in different bonding strengths in the three different configurations. The results showed that the joint structure welded at low temperature were similar to the cold welding without fusion meanwhile the molten phase was presented in the joint when processing at the high temperatures.

  20. Development of joining techniques for fabrication of fuel rod simulators

    International Nuclear Information System (INIS)

    Moorhead, A.J.; McCulloch, R.W.; Reed, R.W.; Woodhouse, J.J.

    1980-10-01

    Much of the safety-related thermal-hydraulic tests on nuclear reactors are conducted not in the reactor itself, but in mockup segments of a core that uses resistance-heated fuel rod simulators (FRS) in place of the radioactive fuel rods. Laser welding and furnace brazing techniques are described for joining subassemblies for FRS that have survived up to 1000 h steady-state operation at 700 to 1100 0 C cladding temperatures and over 5000 thermal transients, ranging from 10 to 100 0 C/s. A pulsed-laser welding procedure that includes use of small-diameter filler wire is used to join one end of a resistance heating element of Pt-8 W, Fe-22 Cr-5.5 Al-0.5 Co, or 80 Ni-20 Cr (wt %) to a tubular conductor of an appropriate intermediate material. The other end of the heating element is laser welded to an end plug, which in turn is welded to a central conductor rod

  1. An empirical study on SAJQ (Sorting Algorithm for Join Queries

    Directory of Open Access Journals (Sweden)

    Hassan I. Mathkour

    2010-06-01

    Full Text Available Most queries that applied on database management systems (DBMS depend heavily on the performance of the used sorting algorithm. In addition to have an efficient sorting algorithm, as a primary feature, stability of such algorithms is a major feature that is needed in performing DBMS queries. In this paper, we study a new Sorting Algorithm for Join Queries (SAJQ that has both advantages of being efficient and stable. The proposed algorithm takes the advantage of using the m-way-merge algorithm in enhancing its time complexity. SAJQ performs the sorting operation in a time complexity of O(nlogm, where n is the length of the input array and m is number of sub-arrays used in sorting. An unsorted input array of length n is arranged into m sorted sub-arrays. The m-way-merge algorithm merges the sorted m sub-arrays into the final output sorted array. The proposed algorithm keeps the stability of the keys intact. An analytical proof has been conducted to prove that, in the worst case, the proposed algorithm has a complexity of O(nlogm. Also, a set of experiments has been performed to investigate the performance of the proposed algorithm. The experimental results have shown that the proposed algorithm outperforms other Stable–Sorting algorithms that are designed for join-based queries.

  2. Glass-ceramic joint and method of joining

    Science.gov (United States)

    Meinhardt, Kerry D [Richland, WA; Vienna, John D [West Richland, WA; Armstrong, Timothy R [Clinton, TN; Pederson, Larry R [Kennewick, WA

    2003-03-18

    The present invention is a glass-ceramic material and method of making useful for joining a solid ceramic component and at least one other solid component. The material is a blend of M1-M2-M3, wherein M1 is BaO, SrO, CaO, MgO, or combinations thereof, M2 is Al.sub.2 O.sub.3, present in the blend in an amount from 2 to 15 mol %, M3 is SiO.sub.2 with up to 50 mol % B.sub.2 O.sub.3 that substantially matches a coefficient of thermal expansion of the solid electrolyte. According to the present invention, a series of glass ceramics in the M1-Al.sub.2 O.sub.3 -M3 system can be used to join or seal both tubular and planar solid oxide fuel cells, oxygen electrolyzers, and membrane reactors for the production of syngas, commodity chemicals and other products.

  3. High Temperature Joining and Characterization of Joint Properties in Silicon Carbide-Based Composite Materials

    Science.gov (United States)

    Halbig, Michael C.; Singh, Mrityunjay

    2015-01-01

    Advanced silicon carbide-based ceramics and composites are being developed for a wide variety of high temperature extreme environment applications. Robust high temperature joining and integration technologies are enabling for the fabrication and manufacturing of large and complex shaped components. The development of a new joining approach called SET (Single-step Elevated Temperature) joining will be described along with the overview of previously developed joining approaches including high temperature brazing, ARCJoinT (Affordable, Robust Ceramic Joining Technology), diffusion bonding, and REABOND (Refractory Eutectic Assisted Bonding). Unlike other approaches, SET joining does not have any lower temperature phases and will therefore have a use temperature above 1315C. Optimization of the composition for full conversion to silicon carbide will be discussed. The goal is to find a composition with no remaining carbon or free silicon. Green tape interlayers were developed for joining. Microstructural analysis and preliminary mechanical tests of the joints will be presented.

  4. Reactive Collision Avoidance Algorithm

    Science.gov (United States)

    Scharf, Daniel; Acikmese, Behcet; Ploen, Scott; Hadaegh, Fred

    2010-01-01

    The reactive collision avoidance (RCA) algorithm allows a spacecraft to find a fuel-optimal trajectory for avoiding an arbitrary number of colliding spacecraft in real time while accounting for acceleration limits. In addition to spacecraft, the technology can be used for vehicles that can accelerate in any direction, such as helicopters and submersibles. In contrast to existing, passive algorithms that simultaneously design trajectories for a cluster of vehicles working to achieve a common goal, RCA is implemented onboard spacecraft only when an imminent collision is detected, and then plans a collision avoidance maneuver for only that host vehicle, thus preventing a collision in an off-nominal situation for which passive algorithms cannot. An example scenario for such a situation might be when a spacecraft in the cluster is approaching another one, but enters safe mode and begins to drift. Functionally, the RCA detects colliding spacecraft, plans an evasion trajectory by solving the Evasion Trajectory Problem (ETP), and then recovers after the collision is avoided. A direct optimization approach was used to develop the algorithm so it can run in real time. In this innovation, a parameterized class of avoidance trajectories is specified, and then the optimal trajectory is found by searching over the parameters. The class of trajectories is selected as bang-off-bang as motivated by optimal control theory. That is, an avoiding spacecraft first applies full acceleration in a constant direction, then coasts, and finally applies full acceleration to stop. The parameter optimization problem can be solved offline and stored as a look-up table of values. Using a look-up table allows the algorithm to run in real time. Given a colliding spacecraft, the properties of the collision geometry serve as indices of the look-up table that gives the optimal trajectory. For multiple colliding spacecraft, the set of trajectories that avoid all spacecraft is rapidly searched on

  5. Collision physics going west

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    The centroid of proton-antiproton physics is moving west across the Atlantic concluded Luigi Di Leila of CERN in his summary talk at the Topical Workshop on Proton-Antiproton Collider Physics, held at Fermilab in June. Previous meetings in this series had been dominated by results from CERN's big proton-antiproton collider, dating back to 1981. However last year saw the first physics run at Fermilab's collider, and although the number of collisions in the big CDF detector was only about one thirtieth of the score so far at CERN, the increased collision energy at Fermilab of 1.8 TeV (1800 GeV, compared to the routine 630 GeV at CERN) is already paying dividends

  6. Frontal sinus fractures: report of one case and review of literature ...

    African Journals Online (AJOL)

    The frontal sinus is a bilateral asymmetric and pyramidal structure located in the frontal bone. It is absent at birth. The frontal sinus is extremely resilient to injury. However, high velocity impacts such as motor vehicle accidents and assaults can result in frontal sinus fractures. Such high velocity impacts lead to aesthetic ...

  7. Recurrent meningitis and frontal encephalocele as delayed complications of craniofacial trauma.

    Science.gov (United States)

    Gumussoy, Murat; Ugur, Omer; Cukurova, Ibrahim; Uluyol, Sinan

    2014-03-01

    Frontal sinus back table fractures are seen rarely; also, typical presentation of frontal sinus encephalocele as a delayed complication of frontal sinus fracture is seen more rarely. We present a case of frontal encephalocele and recurrent meningitis as delayed complications of craniofacial trauma. Diagnosis, management, and treatment approaches of these complications are discussed.

  8. The frontal structure in Drake Passage based on the data of the section in January 2010

    Science.gov (United States)

    Tarakanov, Roman

    2014-05-01

    The frontal structure in the region of Drake Passage is investigated on the basis of data of Absolute Dynamic Topography (ADT) of French agency CLS (DT-Global-MADT-Upd product, http://aviso.oceanobs.com), and CTD- and SADCP-measurements along the hydrophysical section carried out across the passage from Smith Isl. (just to the east of the Hero F.Z.) to the Cape Horn onboard R/V "Akademik Ioffe" in January 2010. The investigation was similar to the analysis performed on the basis of data of the section carried out two weeks earlier onboard the same vessel south of Africa. Fine-jet structure of the ACC was detected in Drake Passage as well as to the south of Africa where twelve ACC jets were found. Eleven jets of the Antarctic Circumpolar Current (ACC) were revealed in Drake Passage. These were five jets of the Subantarctic Current (the band of Subantarctic Front), four jets of the South Polar Current (the band of Polar Front), and two jets of the South Antarctic Current (the band of Southern ACC Front). Two jets of the South Antarctic Current were joined in a single "super-jet" according to the velocity measurements in the section. The others were manifested by the local velocity maxima in the surface layer.

  9. Vehicle related factors that influence injury outcome in head-on collisions.

    Science.gov (United States)

    Blum, Jeremy J; Scullion, Paul; Morgan, Richard M; Digges, Kennerly; Kan, Cing-Dao; Park, Shinhee; Bae, Hanil

    2008-10-01

    This study specifically investigated a range of vehicle-related factors that are associated with a lower risk of serious or fatal injury to a belted driver in a head-on collision. This analysis investigated a range of structural characteristics, quantities that describes the physical features of a passenger vehicle, e.g., stiffness or frontal geometry. The study used a data-mining approach (classification tree algorithm) to find the most significant relationships between injury outcome and the structural variables. The algorithm was applied to 120,000 real-world, head-on collisions, from the National Highway Traffic Safety Administration's (NHTSA's) State Crash data files, that were linked to structural attributes derived from frontal crash tests performed as part of the USA New Car Assessment Program. As with previous literature, the analysis found that the heavier vehicles were correlated with lower injury risk to their drivers. This analysis also found a new and significant correlation between the vehicle's stiffness and injury risk. When an airbag deployed, the vehicle's stiffness has the most statistically significant correlation with injury risk. These results suggest that in severe collisions, lower intrusion in the occupant cabin associated with higher stiffness is at least as important to occupant protection as vehicle weight for self-protection of the occupant. Consequently, the safety community might better improve self-protection by a renewed focus on increasing vehicle stiffness in order to improve crashworthiness in head-on collisions.

  10. Frontal lobe atrophy of the brain in schizophrenia

    International Nuclear Information System (INIS)

    Hara, Tomio

    1981-01-01

    Reported here are the CT findings on cerebral atrophic lesion chiefly developed in the frontal lobe in schizophrenics with unusual organic encephalopathy. Encephalopathy was recognized in 84 (73%) of 115 schizophrenics and 13 (33%) of 40 neurotics. In an attempt to exclude the effects of aging on encephalopathy, the ages at CT and at the development of disease, the number of morbid years, subtypical schizophrenia and relation between the clinical severity and the atrophic condition were comparatively studied. As a result, cerebral atrophy tended to increase along with aging, but the findings differed in that atrophia classified by age covered the entire brain in general, whereas atrophia in schizophrenics was found in the frontal lobe. In particular, because of the fact that clinical severity and atrophia in the frontal lobe are high correlated and that severe atrophia is recognized even in young people, schizophrenia and atrophia in the frontal lobe are considered to be closely related to each other. It is therefore suggested that the CT findings are useful to clinicians for finding appropriate methods to deal with the prognosis of schizophrenics in their daily diagnosis and for the therapeutic prevention of encephalatrophy by stimulating the frontal lobe, thereby delaying mental deterioration. (author)

  11. The validity of individual frontal alpha asymmetry EEG neurofeedback.

    Science.gov (United States)

    Quaedflieg, C W E M; Smulders, F T Y; Meyer, T; Peeters, F; Merckelbach, H; Smeets, T

    2016-01-01

    Frontal asymmetry in alpha oscillations is assumed to be associated with psychopathology and individual differences in emotional responding. Brain-activity-based feedback is a promising tool for the modulation of cortical activity. Here, we validated a neurofeedback protocol designed to change relative frontal asymmetry based on individual alpha peak frequencies, including real-time average referencing and eye-correction. Participants (N = 60) were randomly assigned to a right, left or placebo neurofeedback group. Results show a difference in trainability between groups, with a linear change in frontal alpha asymmetry over time for the right neurofeedback group during rest. Moreover, the asymmetry changes in the right group were frequency and location specific, even though trainability did not persist at 1 week and 1 month follow-ups. On the behavioral level, subjective stress on the second test day was reduced in the left and placebo neurofeedback groups, but not in the right neurofeedback group. We found individual differences in trainability that were dependent on training group, with participants in the right neurofeedback group being more likely to change their frontal asymmetry in the desired direction. Individual differences in trainability were also reflected in the ability to change frontal asymmetry during the feedback. © The Author (2015). Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

  12. Case Report: A Rare Case Report of Frontal Lobe Syndrome

    Directory of Open Access Journals (Sweden)

    Morteza Nouri- Khajavi

    2003-04-01

    Full Text Available The frontal lobe syndrome is a permanent personality change disorder with characteristic clinical pictures, which followed by frontal lobes damage. Clinical picture include: Affective instability, recurrent aggressive behavior, impaired social judgment, apathy and undifferentiating or suspiciousness and paranoid ideations. According DSM-IV classification frontal lobe syndrome named personality change due to head trauma on Axis I. Herein we report a case of 46 years-old man, who has developed behavioral disturbances following head trauma, about 10 years ago. Main clinical figures in this case are apathy, avolition and, undifferentiating. Clinical pictures are constant during these 10 years. The diagnostic approach has been based on patient’s problems history which, has taken from his family, mental status examination, Neurological examination, Brain imaging and Neuropsychological assessments which related to frontal lobes function. Because of rarity & neglection due to mysterious function of frontal lobes, and also considering that personality change from previous level is prominent figure of this syndrome and also brain imaging findings, which compatible with clinical findings, with this aim, we have reported this case.

  13. Research of Joining Brittle Nonmetallic Materials with an Active Solder

    Directory of Open Access Journals (Sweden)

    Roman Koleňák

    2014-01-01

    Full Text Available This paper deals with soldering high-purity brittle, nonmetallic materials such as SiO2, Si, and C (graphite. However, these materials exert poor wettability when using tin solder. Therefore, to reduce the wetting angle, an Sn solder alloyed with active Ti element was used. At a soldering temperature of 860°C and 15 min soldering time, the wetting angle on SiO2 ceramics was 30°, on silicon 42°, and on graphite 52°. All these wetting angles are below 90° and are acceptable for soldering. It has been shown that the bond in all joined materials (SiO2, Si, and C was of a diffusion character. New intermetallic products were formed on the boundary with nonmetal, thus allowing bond formation. The shear strength of SiO2 ceramics attained an average value of 17 MPa.

  14. Retrieval of Spatial Join Pattern Instances from Sensor Networks

    DEFF Research Database (Denmark)

    Yiu, Man Lung; Mamoulis, Nikos; Bakiras, Spiridon

    2009-01-01

    We study the continuous evaluation of spatial join queries and extensions thereof, defined by interesting combinations of sensor readings (events) that co-occur in a spatial neighborhood. An example of such a pattern is "a high temperature reading in the vicinity of at least four high-pressure re...... for sensing, and network topology. Finally, we experimentally compare the effectiveness of the proposed solutions on an experimental platform that emulates real sensor networks.......-pressure readings". We devise protocols for `in-network' evaluation of this class of queries, aiming at the minimization of power consumption. In addition, we develop cost models that suggest the appropriateness of each protocol, based on various factors, including selectivity of query elements, energy requirements...

  15. Soltherm Europe Initiative: Joining forces to expand solar markets, fast

    International Nuclear Information System (INIS)

    Leun, K. van der

    2001-01-01

    The article describes the partnership formed by the European Commission and the Europe-wide Soltherm Europe Initiative. The Initiative was formed in response to the Commission's aims to extend the use of solar energy. Ten countries and two international bodies make-up membership of the Initiative. For the Commission's target of 100 million square metres of solar collectors to be installed by 2010, a rapid growth in the market will need to occur. The potential savings in energy and carbon dioxide (through solar water heaters) are discussed, and figures given. The market development options for achieving the short-term goal of 15 million square metres of collector surface by 2004, and the longer-term aim of 100 million square metres by 2010 are discussed. The Initiative aims to be a platform for integration and promoting co-operation between all parties with an interest in achieving the Commission's solar objectives. Interested parties are invited to join the Initiative

  16. The endless tale of non-homologous end-joining.

    Science.gov (United States)

    Weterings, Eric; Chen, David J

    2008-01-01

    DNA double-strand breaks (DSBs) are introduced in cells by ionizing radiation and reactive oxygen species. In addition, they are commonly generated during V(D)J recombination, an essential aspect of the developing immune system. Failure to effectively repair these DSBs can result in chromosome breakage, cell death, onset of cancer, and defects in the immune system of higher vertebrates. Fortunately, all mammalian cells possess two enzymatic pathways that mediate the repair of DSBs: homologous recombination and non-homologous end-joining (NHEJ). The NHEJ process utilizes enzymes that capture both ends of the broken DNA molecule, bring them together in a synaptic DNA-protein complex, and finally repair the DNA break. In this review, all the known enzymes that play a role in the NHEJ process are discussed and a working model for the co-operation of these enzymes during DSB repair is presented.

  17. Russia joins Kazakh/Omani pipeline venture group

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Russia has agreed to become a founding partner in a joint venture pipeline project formed by Kazakhstan and Oman. The agreement, signed in Bermuda July 24, is related to Chevron Corp.'s further development of supergiant Tengiz and Korolev fields along the Caspian Sea coast in Kazakhstan. Azerbaijan last month signed an agreement to become a founding member of the group, accepting terms agreed to by original joint venturers Kazakhstan and Oman. Azerbaijan's new government still must formally ratify its agreement. In addition, Chevron in June signed a memorandum of understanding to join the group at a future date. This paper reports that each of the founding members holds an equal interest in Caspian Pipeline Consortium Ltd., which will operate as a limited liability company incorporated in Bermuda

  18. Youth in the Netherlands Study (JOiN: study design

    Directory of Open Access Journals (Sweden)

    Huizink Anja C

    2012-05-01

    Full Text Available Abstract Background Adolescence is a critical developmental period regarding exposure to substances. Therefore, it is important to be able to identify those adolescents who are most vulnerable to substance abuse in the (near future. The JOiN study was specifically designed to examine two endophenotypes of adolescent substance use in a normal risk (NR and high risk (HR sample of adolescents: (1 behavioural disinhibition, and (2 individual differences in stress sensitivity. Methods The NR adolescents were part of a longitudinal general population study at the Erasmus Medical Center in Rotterdam, the Netherlands of children and adolescents initially aged 6 to 18 years old. Three assessment waves have been nearly completed, and data are available of N = 711 participants for stress sensitivity measures, and of a subsample of N = 110 for electroencephalography (EEG measures. Added to this study, HR adolescents who had at least one parent with a substance use disorder and who were treated by an outpatient clinic of a primary addiction care provider were approached via their parent(s. In total, N = 83 adolescents formed this HR sample. NR and HR adolescents participated in standardized stress procedure and EEG procedures in our laboratory. Questionnaires were filled out on background variables, behavioural and emotional problems, and substance use, and a diagnostic interview was conducted with adolescents and parents to assess psychopathology symptoms. DNA was collected through saliva or blood samples. Discussion The design of the JOiN study is optimal for examining the predictive role of endophenotypes of adolescent substance use. The combination of different methods, i.e. stress physiology, electrophysiology, genetics, and questionnaire data from several informants on a range of behaviours and environmental factors enables the investigation of the multifactorial nature of adolescent substance use.

  19. Pulsed Joining Of Body-In-White Components

    Energy Technology Data Exchange (ETDEWEB)

    Bonnen, John [Ford Motor Company, Dearborn, MI (United States)

    2014-09-30

    The objective of this project was to develop cost efficient high quality pulsed welding (PW) technology for joining 6xxx Aluminum and High Strength Steel (with tensile strength above 580MPa) components enabling broad usage of hydroformed parts and leading to substantial weight reduction of cars and trucks to reduce US demand on petroleum, lower carbon emissions and energy expenditures. In general, pulsed welding is a form of impact welding where two dissimilar metal pieces are joined by accelerating one to velocities exceeding 300m/s at which point the first piece strikes the second and forms a weld. In this work, two methods were used to accelerate the flyer material: Electro-Magnetic (EM) pulse and Electro-Hydraulic (EH) pulse launching. The advantage of pulsed welding techniques is that welds can be formed between two materials that cannot otherwise be welded: high strength aluminum and high strength steel. The technical objectives of the project included: 1) developing cost affordable production feasible tooling design for PW of 6xxx aluminum to High Strength steel with strengths above 580MPa; 2) demonstrating that fabricated joints can exceed the required service load strength initially at the coupon level and then at the component level; 3) developing fundamental understanding of the mechanisms of joint formation and conditions leading to formation of high quality PW joint; and 4) creating a numerical model predicting the tooling and electric discharge parameters necessary for the joint formation and that satisfy the targeted strength parameters. The project successfully developed: 1) EM and EH pulsed welds between high strength aluminum with tensile strengths exceeding 240MPa and steels exceeding 580MPa; 2) pulsed welds of extrusions with strengths exceeding project requirements; 3) EM and EH flyer launch models and 4) weld interface formation models. However, the grant holder, Ford Motor Company, could see no path to commercialization and the work was

  20. Rare giant frontal sinus osteoma mimicking fibrous dysplasia.

    Science.gov (United States)

    Exley, R P; Markey, A; Rutherford, S; Bhalla, R K

    2015-03-01

    To present the first report of a giant frontal sinus osteoma treated by excision and single-stage reconstruction with custom-made titanium cranioplasty and left orbital roof prostheses. A 31-year-old man with a history of chronic frontal sinusitis presented with a deforming, painless, midline forehead swelling of 11 years' duration, which had been treated unsuccessfully in Nigeria. Differential diagnosis included both benign and malignant bony tumours. Computerised tomography revealed a giant bony frontal sinus tumour extending beyond the sinus roof and breaching the left orbit, consistent with fibrous dysplasia. Given the extent of the tumour, open craniectomy was performed for surgical extirpation. Histological analysis identified multiple osteomas. This surgical approach achieved excellent cosmesis, with no evidence of recurrence at 12-month follow up. Forehead swelling may pose diagnostic and management dilemmas for the ENT surgeon; however, effective management is facilitated by a multidisciplinary approach.

  1. Lower trait frontal theta activity in mindfulness meditators

    Directory of Open Access Journals (Sweden)

    Guaraci Ken Tanaka

    2014-09-01

    Full Text Available Acute and long-term effects of mindfulness meditation on theta-band activity are not clear. The aim of this study was to investigate frontal theta differences between long- and short-term mindfulness practitioners before, during, and after mindfulness meditation. Twenty participants were recruited, of which 10 were experienced Buddhist meditators. Despite an acute increase in the theta activity during meditation in both the groups, the meditators showed lower trait frontal theta activity. Therefore, we suggested that this finding is a neural correlate of the expert practitioners’ ability to limit the processing of unnecessary information (e.g., discursive thought and increase the awareness of the essential content of the present experience. In conclusion, acute changes in the theta band throughout meditation did not appear to be a specific correlate of mindfulness but were rather related to the concentration properties of the meditation. Notwithstanding, lower frontal theta activity appeared to be a trait of mindfulness practices.

  2. Conventional frontal radiographs compared with frontal radiographs obtained from cone beam computed tomography.

    Science.gov (United States)

    Nur, Metin; Kayipmaz, Saadettin; Bayram, Mehmet; Celikoglu, Mevlut; Kilkis, Dogan; Sezgin, Omer Said

    2012-07-01

    To test the hypothesis that there is no difference between measurements performed on conventional frontal radiographs (FRs) and those performed on FRs obtained from cone beam computed tomography (CBCT) scans. This study consisted of conventional FRs and CBCT-constructed FRs obtained from 30 young adult patients. Twenty-three landmarks were identified on both types of cephalometric radiographs. Twenty-one widely used cephalometric variables (14 linear distances, 4 angles, and 3 ratios) were calculated. Paired t-tests were performed to compare the means of corresponding measurements on two cephalometric radiographs of the same patient. Reproducibility of measurements ranged from 0.85 to 0.99 for CBCT-constructed FRs, and from 0.78 to 0.96 for conventional FRs. A statistically significant difference was observed between conventional FRs and CBCT-constructed FRs for all linear measurements (eurR-eurL, loR-loL, moR-moL, zygR-zygL, lapR-lapL, mxR-mxL, maR-maL, umR-umL, lmR-lmL, agR-agL, me-ans) (P .05). However, no statistically significant differences were noted between conventional FRs and CBCT-constructed FRs for ratios and angular measurements (P > .05). The hypothesis was rejected. A difference has been noted between measurements performed on conventional FRs and those performed on CBCT-constructed FRs, particularly in terms of linear measurements.

  3. Head-on collision of large amplitude internal solitary waves of the first mode

    Science.gov (United States)

    Terletska, Kateryna; Maderich, Vladimir; Brovchenko, Igor; Jung, Kyung Tae; Talipova, Tatiana

    2016-04-01

    The dynamics and energetics of a frontal collision of internal solitary waves of depression and elevation of moderate and large amplitudes propagating in a two-layer stratified fluid are studied numerically in frame of the Navier-Stokes equations. It was considered symmetric and asymmetric head-on collisions. We propose the dimensionless characteristic of the wave collision ξ that is the ratio of the wave steepnesses. Wave runup normalized on the amplitude of incoming wave as function of the waves steepness is proposed. Interval 01 corresponds to the larger wave in the case of asymmetric collision. Results of modeling were compared with the results of laboratory experiments [1]. It was shown that the frontal collision of internal solitary waves of moderate amplitude leads to a small phase shift and to the generation of dispersive wavetrain trailing behind transmitted solitary wave. The phase shift grows with increasing amplitudes of the interacting waves and approaches the limiting value when amplitudes of the waves are equal to the upper/lower layer for waves of depression/elevation. The deviation of the maximum wave height during collision from the twice the amplitude are maximal when wave amplitudes are equal to the upper/lower layer for waves of depression/elevation, then it decays with growth of amplitudes of interacting waves. It was found that the interaction of waves of large amplitude leads to the shear instability and the formation of Kelvin - Helmholtz vortices in the interface layer, however, subsequently waves again become stable. References [1] R.-C. Hsu, M. H. Cheng, C.-Y. Chen, Potential hazards and dynamical analysis of interfacial solitary wave interactions. Nat Hazards. 65 (2013) 255-278

  4. Ship Collision and Grounding Analysis

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    2010-01-01

    It is the purpose of the paper to present a review of prediction and analysis tools for collision and grounding analyses and to outline a probabilistic procedure whereby these tools can be used by the maritime industry to develop performance based rules to reduce the risk associated with human......, environmental and economic costs of collision and grounding events. The main goal of collision and grounding research should be to identify the most economic risk control options associated with prevention and mitigation of collision and grounding events...

  5. Road rage and collision involvement.

    Science.gov (United States)

    Mann, Robert E; Zhao, Jinhui; Stoduto, Gina; Adlaf, Edward M; Smart, Reginald G; Donovan, John E

    2007-01-01

    To assess the contribution of road rage victimization and perpetration to collision involvement. The relationship between self-reported collision involvement and road rage victimization and perpetration was examined, based on telephone interviews with a representative sample of 4897 Ontario adult drivers interviewed between 2002 and 2004. Perpetrators and victims of both any road rage and serious road rage had a significantly higher risk of collision involvement than did those without road rage experience. This study provides epidemiological evidence that both victims and perpetrators of road rage experience increased collision risk. More detailed studies of the contribution of road rage to traffic crashes are needed.

  6. Topics in atomic collision theory

    CERN Document Server

    Geltman, Sydney; Brueckner, Keith A

    1969-01-01

    Topics in Atomic Collision Theory originated in a course of graduate lectures given at the University of Colorado and at University College in London. It is recommended for students in physics and related fields who are interested in the application of quantum scattering theory to low-energy atomic collision phenomena. No attention is given to the electromagnetic, nuclear, or elementary particle domains. The book is organized into three parts: static field scattering, electron-atom collisions, and atom-atom collisions. These are in the order of increasing physical complexity and hence necessar

  7. Gaint frontal sinus mucocoele with intracranial extension and Orbital ...

    African Journals Online (AJOL)

    On avait opéré tout de suite un défaut surgissant à partir d'os frontal à l'aide d'un acier métallique d'une longueur de 0,5mm courbé et attaché en trios couches en traves l'os infecté, l'os frontal par-dessus lequel on avait traité les tissues mou du front à travers l'occlusion primaire sur la sonde d'os (sound bone).

  8. An Adaptive Genetic Algorithm with Dynamic Population Size for Optimizing Join Queries

    OpenAIRE

    Vellev, Stoyan

    2008-01-01

    The problem of finding the optimal join ordering executing a query to a relational database management system is a combinatorial optimization problem, which makes deterministic exhaustive solution search unacceptable for queries with a great number of joined relations. In this work an adaptive genetic algorithm with dynamic population size is proposed for optimizing large join queries. The performance of the algorithm is compared with that of several classical non-determinis...

  9. Joining the UN global compact in Spain: an institutional approach

    Directory of Open Access Journals (Sweden)

    Ainhoa Garayar Erro

    2012-12-01

    Full Text Available The aim of this study is to analyse the incentives for Spanish organisations that have adopted a voluntary code of conduct such as the United Nations Global Compact – GC. In the light of the sociological approach of neoinstitutional theory, we sought to determine the main isomorphic processes that result from joining the GC and factors of the institutional field that might undermine the legitimacy of organisations participating in this voluntary initiative.On the one hand, the main results, while not conclusive, showed that Spanish participants in the GC have more than one reason for joining the initiative. The study’s findings suggest that both institutional processes of mimetic isomorphism and normative isomorphism explain participation in the GC, which emphasizes the improvement in employee satisfaction, an improvement in customer satisfaction and also the fact of being part of sustainable development efforts.On the other hand, it can be asserted that the respondent organisations do not perceive major threats from the institutional environment that might undermine the legitimacy gained by joining the GC. Nonetheless, the Spanish organisations participating in the GC highlight the fact that the main institutional factor that might undermine the organization’s legitimacy is weak governance and corruption.RESUMENEl presente trabajo examina la incidencia que la adopción del Pacto Mundial de Naciones Unidas –PM– ha tenido en organizaciones españolas. En concreto, el objetivo es aportar evidencia sobre las motivaciones que impulsan a un grupo de entidades a participar en esta iniciativa voluntaria. Basándonos en el enfoque sociológico de la teoría neoinstitucional, analizamos los principales procesos de isomorfismo resultantes del proceso de adhesión, así como aquellos factores del entorno institucional que pueden llegar a mermar su legitimidad.Los resultados, aunque no concluyentes, muestran que las organizaciones espa

  10. Ship collision with iceberg database

    Energy Technology Data Exchange (ETDEWEB)

    Hill, B.T. [National Research Council of Canada, St. John' s, NL (Canada). Inst. for Ocean Technology

    2006-11-15

    Approximately 20 per cent of collisions between icebergs, steam ships and motor vessels since 1850 have resulted in sinkings. The available data indicates that most sinkings were due to some kind of indirect impact rather than a head on collision. This paper presented the newly augmented Microsoft Access Database of Ship Collisions with Icebergs that includes more than 670 events over 200 years, most of which occurred on the Grand Banks. Other collisions occurred further afield in the Arctic, off Greenland and in the fjords of Alaska. The operation, search categories and data fields of the database were described along with various trends of collisions, scope of damage and environmental factors involved. Based on an estimate of the number of voyages over the Grand Banks, a probability of collision was derived from the number of cargo ship collisions over the past several years. The Microsoft Access template was provided by the Canadian Hydraulic Centre which had been developed by them for their Ice Regime Database to describe sea ice and ship interactions. This template was adapted and modified for iceberg collisions. Where possible, the data base was augmented to include information about the nature of the damage, the weather and sea state, the ice conditions, iceberg size, the vessel route and location at the time of collision, and vessel characteristics. The purpose of the database is to provide operators and regulators with an assessment of the frequency of collisions and environmental factors that played a role at the time of the collision. The database provides a basis to undertake risk analysis for vessels entering a given area and provides a better understanding of conditions under which collisions are likely to occur. It was concluded that although the trend of collisions has improved over the years with better observation and detection techniques, collisions still occur. Reduced visibility by fog, precipitation or low light conditions were found to be

  11. Electron collisions with biomolecules

    International Nuclear Information System (INIS)

    McKoy, V; Winstead, C

    2008-01-01

    We report on results of recent studies of collisions of low-energy electrons with nucleobases and other DNA constituents. A particular focus of these studies has been the identification and characterization of resonances that play a role in electron attachment leading to strand breaks in DNA. Comparison of the calculated resonance positions with results of electron transmission measurements is quite encouraging. However, the higher-lying π* resonances of the nucleobases appear to be of mixed elastic and core-excited character. Such resonant channel coupling raises the interesting possibility that the higher π*resonances in the nucleobases may promote dissociation of DNA by providing doorway states to triplet excited states.

  12. Molecular collision theory

    CERN Document Server

    Child, M S

    2010-01-01

    This high-level monograph offers an excellent introduction to the theory required for interpretation of an increasingly sophisticated range of molecular scattering experiments. There are five helpful appendixes dealing with continuum wavefunctions, Green's functions, semi-classical connection formulae, curve-crossing in the momentum representation, and elements of classical mechanics.The contents of this volume have been chosen to emphasize the quantum mechanical and semi-classical nature of collision events, with little attention given to purely classical behavior. The treatment is essentiall

  13. Manufacturing and joining technologies for helium cooled divertors

    International Nuclear Information System (INIS)

    Aktaa, J.; Basuki, W.W.; Weber, T.; Norajitra, P.; Krauss, W.; Konys, J.

    2014-01-01

    Highlights: • The manufacturing and joining technologies developed at KIT for helium cooled divertors are reviewed and critically discussed. • Various technologies have been pursued and further developed aiming divertor components with very high quality and sufficient reliability. • Very promising routes have been found for which however still R and D works are necessary. • Technologies developed are also useful for other divertor and even blanket concepts, particularly those with tungsten armor. - Abstract: In the helium cooled (HC) divertor, developed at KIT for a fusion power plant, tungsten has been selected as armor as well as structural material due to its crucial properties: high melting point, very low sputtering yield, good thermal conductivity, high temperature strength, low thermal expansion and low activation. Thereby the armor tungsten is attached to the structural tungsten by thermally conductive joint. Due to the brittleness of tungsten at low temperatures its use as structural material is limited to the high temperature part of the component and a structural joint to the reduced activation ferritic martensitic steel EUROFER97 is foreseen. Hence, to realize the selected hybrid material concept reliable tungsten–steel and tungsten–tungsten joints have been developed and will be reported in this paper. In addition, the modular design of the HC divertor requires tungsten armor tiles and tungsten structural thimbles to be manufactured in high numbers with very high quality. Due to the high strength and low temperature brittleness of tungsten special manufacturing techniques need to be developed for the production of parts with no cavities inside and/or surface flaws. The main achievement in developing the respective manufacturing technologies will be presented and discussed. To achieve the objectives mentioned above various manufacturing and joining technologies are pursued. Their later applicability depends on the level of development

  14. Joining of Ion Transport Membranes Using a Novel Transient Liquid Phase Process

    Energy Technology Data Exchange (ETDEWEB)

    Darryl P. Butt

    2006-08-30

    The feasibility of a novel transient liquid phase (TLP) joining method has been demonstrated in joining La{sub 0.9}Ca{sub 0.1}FeO{sub 3} materials. Metal oxide powders were processed to form the TLP compositions which were used in the joining process. The method has been successful in producing joint interfaces that effectively disappear, as they are the same material and have the same properties as the joined parts. The feasibility of the method has been demonstrated for a single system, but many systems where the method can potentially be applied have been identified.

  15. A review of the US joining technologies for plasma facing components in the ITER fusion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Odegard, B.C. Jr.; Cadden, C.H. [Sandia National Labs., Livermore, CA (United States); Watson, R.D. [Sandia National Labs., Albuquerque, NM (United States); Slattery, K.T. [Boeing Co., St. Louis, MO (United States)

    1998-02-01

    This paper is a review of the current joining technologies for plasma facing components in the US for the International Thermonuclear Experimental Reactor (ITER) project. Many facilities are involved in this project. Many unique and innovative joining techniques are being considered in the quest to join two candidate armor plate materials (beryllium and tungsten) to a copper base alloy heat sink (CuNiBe, OD copper, CuCrZr). These techniques include brazing and diffusion bonding, compliant layers at the bond interface, and the use of diffusion barrier coatings and diffusion enhancing coatings at the bond interfaces. The development and status of these joining techniques will be detailed in this report.

  16. A review of the US joining technologies for plasma facing components in the ITER fusion reactor

    International Nuclear Information System (INIS)

    Odegard, B.C. Jr.; Cadden, C.H.; Watson, R.D.; Slattery, K.T.

    1998-02-01

    This paper is a review of the current joining technologies for plasma facing components in the US for the International Thermonuclear Experimental Reactor (ITER) project. Many facilities are involved in this project. Many unique and innovative joining techniques are being considered in the quest to join two candidate armor plate materials (beryllium and tungsten) to a copper base alloy heat sink (CuNiBe, OD copper, CuCrZr). These techniques include brazing and diffusion bonding, compliant layers at the bond interface, and the use of diffusion barrier coatings and diffusion enhancing coatings at the bond interfaces. The development and status of these joining techniques will be detailed in this report

  17. Transient-Liquid-Phase and Liquid-Film-Assisted Joining ofCeramics

    Energy Technology Data Exchange (ETDEWEB)

    Sugar, Joshua D.; McKeown, Joseph T.; Akashi, Takaya; Hong, SungM.; Nakashima, Kunihiko; Glaeser, Andreas M.

    2005-02-09

    Two joining methods, transient-liquid-phase (TLP) joining and liquid-film-assisted joining (LFAJ), have been used to bond alumina ceramics. Both methods rely on multilayer metallic interlayers designed to form thin liquid films at reduced temperatures. The liquid films either disappear by interdiffusion (TLP) or promote ceramic/metal interface formation and concurrent dewetting of the liquid film (LFAJ). Progress on extending the TLP method to lower temperatures by combining low-melting-point (<450 C) liquids and commercial reactive-metal brazes is described. Recent LFAJ work on joining alumina to niobium using copper films is presented.

  18. Efficient string similarity join in multi-core and distributed systems.

    Directory of Open Access Journals (Sweden)

    Cairong Yan

    Full Text Available In big data area a significant challenge about string similarity join is to find all similar pairs more efficiently. In this paper, we propose a parallel processing framework for efficient string similarity join. First, the input is split into some disjoint small subsets according to the joint frequency distribution and the interval distribution of strings. Then the filter-verification strategy is adopted in the computation of string similarity for each subset so that the number of candidate pairs is reduced before an effective pruning strategy is used to improve the performance. Finally, the operation of string join is executed in parallel. Para-Join algorithm based on the multi-threading technique is proposed to implement the framework in a multi-core system while Pada-Join algorithm based on Spark platform is proposed to implement the framework in a cluster system. We prove that Para-Join and Pada-Join cannot only avoid reduplicate computation but also ensure the completeness of the result. Experimental results show that Para-Join can achieve high efficiency and significantly outperform than state-of-the-art approaches, meanwhile, Pada-Join can work on large datasets.

  19. UHV compatible Al to SS joining through electro magnetic forming technique

    International Nuclear Information System (INIS)

    Prasad, N K; Ram, Y; Sabharwal, T P; Pathak, K; Kumar, M; Matkar, A W; Rajawat, R K

    2008-01-01

    Fusion welding, which is the most versatile and widely used method of metallurgical bonding, can be troublesome in certain applications like dissimilar metal joining for Ultra High Vacuum requirements. Welding of Stainless Steel to Aluminum by conventional technique is very difficult due to thermal and metallurgical incompatibility. Consequently a number of non-conventional specialized joining techniques were developed. Joining of SS to Al by Electro Magnetic Forming (EMF) method is an effort in this direction. The paper discusses in detail the joining process, joint design and the results achieved

  20. Cyclonic entrainment of preconditioned shelf waters into a frontal eddy

    Science.gov (United States)

    Everett, J. D.; Macdonald, H.; Baird, M. E.; Humphries, J.; Roughan, M.; Suthers, I. M.

    2015-02-01

    The volume transport of nutrient-rich continental shelf water into a cyclonic frontal eddy (entrainment) was examined from satellite observations, a Slocum glider and numerical simulation outputs. Within the frontal eddy, parcels of water with temperature/salinity signatures of the continental shelf (18-19°C and >35.5, respectively) were recorded. The distribution of patches of shelf water observed within the eddy was consistent with the spiral pattern shown within the numerical simulations. A numerical dye tracer experiment showed that the surface waters (≤50 m depth) of the frontal eddy are almost entirely (≥95%) shelf waters. Particle tracking experiments showed that water was drawn into the eddy from over 4° of latitude (30-34.5°S). Consistent with the glider observations, the modeled particles entrained into the eddy sunk relative to their initial position. Particles released south of 33°S, where the waters are cooler and denser, sunk 34 m deeper than their release position. Distance to the shelf was a critical factor in determining the volume of shelf water entrained into the eddy. Entrainment reduced to 0.23 Sv when the eddy was furthest from the shelf, compared to 0.61 Sv when the eddy was within 10 km of the shelf. From a biological perspective, quantifying the entrainment of shelf water into frontal eddies is important, as it is thought to play a significant role in providing an offshore nursery habitat for coastally spawned larval fish.

  1. Relationship between ankle frontal plane kinematics during different functional tasks.

    Science.gov (United States)

    Donovan, Luke; Feger, Mark A

    2017-05-01

    Increased inversion following lateral ankle sprain and in patients with chronic ankle instability (CAI) is thought to contribute to recurrent injury and feelings of instability, however, there are no biomechanic assessment tools readily available to evaluate for excessive inversion prior to or following lateral ankle sprains. Before establishing a clinically useful biomechanic assessment tool, it is important to understand whether there is a relationship in the extent of ankle frontal plane motion across various tasks to help determine if one task or a combination of tasks would be most appropriate when evaluating patients. The purpose of this preliminary study was to analyze the relationship between ankle frontal plane kinematics during walking, step-down, and jump-landing tasks. Fifty-six recreationally active adults (gender=M:26;F:30, age=21.2±3.2, height=171.3±8.0cm, mass=75.6±15.4) volunteered. Main outcome measures were ankle frontal plane motion at initial contact and peak inversion during aerial phases across 3 tasks (walking, step-down, and jump-landing). Relationships between ankle frontal plane kinematics were analyzed by Pearson product-moment correlation coefficient (r). There were strong correlations in peak inversion during the aerial phase between the step-down and walking (r=0.68; pbiomechanics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Frontal EEG Asymmetry of Mood: A Mini-Review

    Directory of Open Access Journals (Sweden)

    Massimiliano Palmiero

    2017-11-01

    Full Text Available The present mini-review was aimed at exploring the frontal EEG asymmetry of mood. With respect to emotion, interpreted as a discrete affective process, mood is more controllable, more nebulous, and more related to mind/cognition; in addition, causes are less well-defined than those eliciting emotion. Therefore, firstly, the rational for the distinction between emotion and mood was provided. Then, the main frontal EEG asymmetry models were presented, such as the motivational approach/withdrawal, valence/arousal, capability, and inhibition asymmetric models. Afterward, the frontal EEG asymmetry of mood was investigated following three research lines, that is considering studies involving different mood induction procedures, dispositional mood (positive and negative affect, and mood alterations in both healthy and clinical populations. In general, results were found to be contradictory, no model is unequivocally supported regardless the research line considered. Different methodological issues were raised, such as: the composition of samples used across studies, in particular, gender and age were found to be critical variables that should be better addressed in future studies; the importance of third variables that might mediate the relationship between frontal EEG asymmetries and mood, for example bodily states and hormonal responses; the role of cognition, namely the interplay between mood and executive functions. In light of these issues, future research directions were proposed. Amongst others, the need to explore the neural connectivity that underpins EEG asymmetries, and the need to include both positive and negative mood conditions in the experimental designs have been highlighted.

  3. Apolipoprotein E gene and sporadic frontal lobe dementia.

    NARCIS (Netherlands)

    M. Stevens (Martijn); C.M. van Duijn (Cornelia); P. de Knijff (Peter); B.A. Oostra (Ben); M.F. Niermeijer (Martinus); J.C. van Swieten (John); P. Heutink (Peter); C. van Broeckhoven (Christine)

    1997-01-01

    textabstractThe apolipoprotein E gene has been associated with various types of dementia. We studied the connection between the APOE gene and the risk and onset of disease in 34 patients with clinically diagnosed frontal lobe dementia (FLD) derived from a population-based study in the Netherlands. A

  4. High density scalp EEG in frontal lobe epilepsy.

    Science.gov (United States)

    Feyissa, Anteneh M; Britton, Jeffrey W; Van Gompel, Jamie; Lagerlund, Terrance L; So, Elson; Wong-Kisiel, Lilly C; Cascino, Gregory C; Brinkman, Benjamin H; Nelson, Cindy L; Watson, Robert; Worrell, Gregory A

    2017-01-01

    Localization of seizures in frontal lobe epilepsy using the 10-20 system scalp EEG is often challenging because neocortical seizure can spread rapidly, significant muscle artifact, and the suboptimal spatial resolution for seizure generators involving mesial frontal lobe cortex. Our aim in this study was to determine the value of visual interpretation of 76 channel high density EEG (hdEEG) monitoring (10-10 system) in patients with suspected frontal lobe epilepsy, and to evaluate concordance with MRI, subtraction ictal SPECT co-registered to MRI (SISCOM), conventional EEG, and intracranial EEG (iEEG). We performed a retrospective cohort study of 14 consecutive patients who underwent hdEEG monitoring for suspected frontal lobe seizures. The gold standard for localization was considered to be iEEG. Concordance of hdEEG findings with MRI, subtraction ictal SPECT co-registered to MRI (SISCOM), conventional 10-20 EEG, and iEEG as well as correlation of hdEEG localization with surgical outcome were examined. hdEEG localization was concordant with iEEG in 12/14 and was superior to conventional EEG 3/14 (pfrontal epilepsy requiring localization of epileptogenic brain. hdEEG may assist in developing a hypothesis for iEEG monitoring and could potentially augment EEG source localization. Published by Elsevier B.V.

  5. Time Ordering in Frontal Lobe Patients: A Stochastic Model Approach

    Science.gov (United States)

    Magherini, Anna; Saetti, Maria Cristina; Berta, Emilia; Botti, Claudio; Faglioni, Pietro

    2005-01-01

    Frontal lobe patients reproduced a sequence of capital letters or abstract shapes. Immediate and delayed reproduction trials allowed the analysis of short- and long-term memory for time order by means of suitable Markov chain stochastic models. Patients were as proficient as healthy subjects on the immediate reproduction trial, thus showing spared…

  6. Charting the Maturation of the Frontal Lobe: An Electrophysiological Strategy

    Science.gov (United States)

    Segalowitz, S. J.; Davies, Patricia L.

    2004-01-01

    Tracking the functional development of specific regions of the prefrontal cortex in children using event-related potentials (ERPs) is challenging for both technical and conceptual reasons. In this paper we outline our strategy for studying frontal lobe development and present preliminary results from children aged 7-17 years and young adults using…

  7. Relationships between foot type and dynamic rearfoot frontal plane motion.

    Science.gov (United States)

    Chuter, Vivienne H

    2010-06-16

    The Foot Posture Index (FPI) provides an easily applicable, validated method for quantifying static foot posture. However there is limited evidence relating to the ability of the FPI to predict dynamic foot function. This study aimed to assess the relationship between dynamic rearfoot motion and FPI scores in pronated and normal foot types. 40 participants were recruited with equal numbers of pronated and normal foot types as classified by their FPI score. Three dimensional rearfoot motion was collected for each of the participants. Dynamic maximum rearfoot eversion was correlated with the total FPI score across all participants and within the normal and pronated foot types. Linear correlations were performed between components of the total FPI scores measuring frontal plane rearfoot position and maximum rearfoot eversion. The capacity of the total FPI score to predict maximum frontal plane motion of the rearfoot was investigated using linear regression analysis. The correlation between the total FPI score and maximum rearfoot eversion was strongly positive (r = 0.92, p foot type (FPI = +6 to +9) and maximum rearfoot eversion angle were more strongly positively correlated (r = 0.81, p foot type (FPI = 0 to +5) and maximum rearfoot eversion (r = 0.76, p plane rearfoot FPI score and frontal plane motion during gait were strongly positive, (r = 0.79 p foot type. Positive correlations between frontal plane rearfoot measurements and maximum rearfoot eversion suggest the FPI may identify dominant planar components of dynamic rearfoot motion and warrants further investigation.

  8. Role of Frontal Cortex in Attentional Capture by Singleton Distractors

    Science.gov (United States)

    de Fockert, Jan W.; Theeuwes, Jan

    2012-01-01

    The role of frontal cortex in selective attention to visual distractors was examined in an attentional capture task in which participants searched for a unique shape in the presence or absence of an additional colour singleton distractor. The presence of the additional singleton was associated with slower behavioural responses to the shape target,…

  9. Finite element modelling of helmeted head impact under frontal ...

    Indian Academy of Sciences (India)

    Abstract. Finite element models of the head and helmet were used to study contact forces during frontal impact of the head with a rigid surface. The finite element model of the head consists of skin, skull, cerebro-spinal fluid (CSF), brain, tentorium and falx. The finite element model of the helmet consists of shell and foam.

  10. Management Of Fractures Involving Anterior Wall Of Frontal Sinus ...

    African Journals Online (AJOL)

    Nondisplaced or minimally displaced (<1-2 mm) isolated anterior table fractures can be managed conservatively with local wound care and analgesics. Patients with mildly displaced anterior table fractures do extremely well after surgical repair. We discuss the relevant anatomy of frontal sinus and management of fractures ...

  11. Bilingualism Alters Children's Frontal Lobe Functioning for Attentional Control

    Science.gov (United States)

    Arredondo, Maria M.; Hu, Xiao-Su; Satterfield, Teresa; Kovelman, Ioulia

    2017-01-01

    Bilingualism is a typical linguistic experience, yet relatively little is known about its impact on children's cognitive and brain development. Theories of bilingualism suggest that early dual-language acquisition can improve children's cognitive abilities, specifically those relying on frontal lobe functioning. While behavioral findings present…

  12. Obsessive-compulsive disorder and ventromedial frontal lesions

    DEFF Research Database (Denmark)

    Irle, E; Exner, C; Thielen, K

    1998-01-01

    subjects who had undergone ventromedial frontal leukotomy were evaluated clinically and neuropsychologically and compared to seven well comparison OCD subjects without leukotomy. The 16 leukotomized subjects were divided into three groups according to the main lesion sites as determined by current magnetic...

  13. Anthropometrical Profiles Of The Frontal Sinus In Population Of ...

    African Journals Online (AJOL)

    The anthropometrical profiles, function and variation of frontal sinus have been poorly understood. Understanding these are important in sinus operation and in paleontology, to understand the puzzle of the meaning of the supra orbital development. In the present study radiographs of 74 males and 46 females of south east ...

  14. Chondromyxoid fibroma of the frontal bone in a teenager

    International Nuclear Information System (INIS)

    Kadom, Nadja; Rushing, Elisabeth J.; Yaun, Amanda; Santi, Mariarita

    2009-01-01

    We report a skull chondromyxoid fibroma with symptomatic intracranial extension causing initial misdiagnosis as a psychiatric disorder in a 14-year-old child. CT performed for work-up of the patient's ''stuffy nose'' revealed a large calcified frontal bone mass with extensive intracranial growth. We present this child with the diagnosis of intracranial chondromyxoid fibroma with detailed neuroimaging and neuropathology correlations. (orig.)

  15. Video-assisted resection in benign frontal tumors.

    Science.gov (United States)

    Guerrissi, Jorge Orlando

    2015-01-01

    Soft and osseous tumors that develop into the frontal are the most profitable with the use of video-assisted surgery, thus avoiding also a visible scar. In the Department of Plastic Surgery at Argerich Hospital in Buenos Aires, Argentina, from 1999 to 2010, video-assisted operations were used in the treatment of 158 patients, 26 of them presented lipomas and osteomas into the frontal tissues. In all 26 patients, both local anesthesia and incisions behind the hairline were performed. Minor complications such as hematoma and transitory paresis of the frontal nerve were detected. Video-assisted technique offered both good illumination and excellent magnification that not only permits a safe anatomic dissection by means of surgical maneuvers in avascular planes but also avoids visible scars. The outcome achieved with endoscopic techniques has permitted to consider it like the first election in the surgical treatment in tumors developed into both soft and osseous tissues of the frontal area, offering more advantages than the classic approaches.

  16. Structures and morphotectonic evolution of the frontal fold–thrust ...

    Indian Academy of Sciences (India)

    52

    The differential movement of the mountain front on both sides of the ramp is decipherable. 23. This is especially true ..... Further movement along the Frontal Fault deformed Siwalik sediments. Siwalik sediments ..... Poblet J and Lisle R J 2011 Kinematic evolution and structural styles of fold-and-thrust belts;. 391. Geol. Soc.

  17. CONFERENCE: Photon-photon collisions

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    Despite being difficult to observe, photon-photon collisions have opened up a range of physics difficult, or even impossible, to access by other methods. The progress which has been made in this field was evident at the fifth international workshop on photon-photon collisions, held in Aachen from 13-16 April and attended by some 120 physicists

  18. Outer Dynamics of Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisions with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding structures....

  19. Joining of alumina via copper/niobium/copper interlayers

    Energy Technology Data Exchange (ETDEWEB)

    Marks, Robert A.; Chapman, Daniel R.; Danielson, David T.; Glaeser, Andreas M.

    2000-03-15

    Alumina has been joined at 1150 degrees C and 1400 degrees C using multilayer copper/niobium/copper interlayers. Four-point bend strengths are sensitive to processing temperature, bonding pressure, and furnace environment (ambient oxygen partial pressure). Under optimum conditions, joints with reproducibly high room temperature strengths (approximately equal 240 plus/minus 20 MPa) can be produced; most failures occur within the ceramic. Joints made with sapphire show that during bonding an initially continuous copper film undergoes a morphological instability, resulting in the formation of isolated copper-rich droplets/particles at the sapphire/interlayer interface, and extensive regions of direct bonding between sapphire and niobium. For optimized alumina bonds, bend tests at 800 degrees C-1100 degrees C indicate significant strength is retained; even at the highest test temperature, ceramic failure is observed. Post-bonding anneals at 1000 degrees C in vacuum or in gettered argon were used to assess joint stability and to probe the effect of ambient oxygen partial pressure on joint characteristics. Annealing in vacuum for up to 200 h causes no significant decrease in room temperature bend strength or change in fracture path. With increasing anneal time in a lower oxygen partial pressure environment, the fracture strength decreases only slightly, but the fracture path shifts from the ceramic to the interface.

  20. An active micro joining mechanism for 3D assembly

    International Nuclear Information System (INIS)

    Mayyas, Mohammad; Zhang Ping; Lee, Woo Ho; Popa, Dan; Chiao, J C

    2009-01-01

    An active joining mechanism for the construction of microstructures, comprising detethered microparts and locking actuators fabricated on a wafer, has been implemented. An active locking mechanism is a system on chip (SOC) type of actuator which is designed to control the socket's opening to allow insertion of a micropart with zero force. This allows the delicate micropart to be secured without the need of substantial forces that could cause damage to the micropart or the socket. Moreover, it enhances the assembly throughput, tolerance and yield due to the frictionless self-alignment of the micropart. The design concept, assembly and extensive characterization have been illustrated for 100 µm thick microstructures made of SOI wafers and patterned by deep reactive ion etching. Single-sided and double-sided electrothermal bent beam actuators are utilized for the socket to actively open during assembly and close to lock the micropart against the locking mechanism. Finally, the mechanical and electrical characteristics of the joints can be further enhanced by reflow of the deposited layers of the 80Au–20Sn solder alloy at the contact areas

  1. Joining characteristics of orthodontic wires with laser welding.

    Science.gov (United States)

    Iijima, Masahiro; Brantley, William A; Yuasa, Toshihiro; Muguruma, Takeshi; Kawashima, Isao; Mizoguchi, Itaru

    2008-01-01

    Laser welding 0.016 x 0.022 in. beta-Ti, Ni-Ti, and Co-Cr-Ni orthodontic wires was investigated by measuring joint tensile strength, measuring laser penetration depth, determining metallurgical phases using micro X-ray diffraction (micro-XRD), and examining microstructures with an scanning electron microscope (SEM). Welding was performed from 150 to 230 V. Mean tensile strength for Ni-Ti groups was significantly lower (p Ni was significantly lower than for control specimens joined by silver soldering, it was sufficient for clinical use. The beta-Ti orthodontic wire showed deeper penetration depth from laser welding than the Ni-Ti and Co-Cr-Ni orthodontic wires. Micro-XRD patterns of laser-welded beta-Ti and Ni-Ti obtained 2 mm from the boundary were similar to as-received specimens, indicating that original microstructures were maintained. When output voltages of 190 V and higher were used, most peaks from joint areas disappeared or were much weaker, perhaps because of a directional solidification effect, evidenced by SEM observation of fine striations in welded beta-Ti. Laser welding beta-Ti and Co-Cr-Ni wires may be acceptable clinically, since joints had sufficient strength and metallurgical phases in the original wires were not greatly altered.

  2. Asian international students' barriers to joining group counseling.

    Science.gov (United States)

    Lee, Ji-Yeon

    2014-10-01

    This cross-sectional study examined anticipated reactions to group participation among Asian international students (ISs). Structural equation modeling confirmed that Asian ISs' (n = 180) level of acculturation was associated with their attitude toward joining group counseling, which is partially mediated by their stigma toward help-seeking. The results of multiple regression analyses indicated that ISs who reported higher place dependence, stigma toward help-seeking, and fear of negative evaluation reported more fear about disclosing emotional parts of themselves to other group members in the presence of a group member from the same country of origin. The results showed that ISs' perceived difficulties in providing feedback to a group member in the presence of an IS from the same country of origin were predicted by low place identity, high place dependence, and more stigma. International students' willingness to disclose and provide feedback in a group counseling setting was compared in three different hypothetical situations based on other group members' demographics, and the results showed that ISs are more afraid of self-disclosure in the presence of an international student from the same country.

  3. Predictive modeling of reactive wetting and metal joining.

    Energy Technology Data Exchange (ETDEWEB)

    van Swol, Frank B.

    2013-09-01

    The performance, reproducibility and reliability of metal joints are complex functions of the detailed history of physical processes involved in their creation. Prediction and control of these processes constitutes an intrinsically challenging multi-physics problem involving heating and melting a metal alloy and reactive wetting. Understanding this process requires coupling strong molecularscale chemistry at the interface with microscopic (diffusion) and macroscopic mass transport (flow) inside the liquid followed by subsequent cooling and solidification of the new metal mixture. The final joint displays compositional heterogeneity and its resulting microstructure largely determines the success or failure of the entire component. At present there exists no computational tool at Sandia that can predict the formation and success of a braze joint, as current capabilities lack the ability to capture surface/interface reactions and their effect on interface properties. This situation precludes us from implementing a proactive strategy to deal with joining problems. Here, we describe what is needed to arrive at a predictive modeling and simulation capability for multicomponent metals with complicated phase diagrams for melting and solidification, incorporating dissolutive and composition-dependent wetting.

  4. Indian oil company joins efforts to reduce methane emissions

    Science.gov (United States)

    Kumar, Mohi

    The Oil and Natural Gas Corp, Ltd. (ONGC), headquartered in Dehradun, India, has joined seven U.S. and Canadian oil and natural gas companies as a partner in a U.S. Environmental Protection Agency program to reduce greenhouse gas emissions. EPA's Natural Gas STAR International Program aims to reduce methane emissions from the oil and natural gas sector while delivering more gas to markets around the world. With this partnership, ONGC agrees to implement emissions reduction practices and to submit annual reports on progress achieved; EPA agrees to assist ONGC with training technicians in new cost-effective technologies that will help achieve target emissions. The Natural Gas STAR International Program is administered under the Methane to Markets Partnership, a group of 20 countries and 600 companies across the globe that since 2004 has volunteered to cut methane emissions. More information on EPA's agreement with ONGC can be found at http://www.epa.gov/gasstar/index.htm; information about the Methane to Markets Partnership can be found at http://www.methanetomarkets.org.

  5. Joining Forces: The Chemical Biology-Medicinal Chemistry Continuum.

    Science.gov (United States)

    Plowright, Alleyn T; Ottmann, Christian; Arkin, Michelle; Auberson, Yves P; Timmerman, Henk; Waldmann, Herbert

    2017-09-21

    The scientific advances being made across all disciplines are creating ever-increasing opportunities to enhance our knowledge of biological systems and how they relate to human disease. One of the central driving forces in discovering new medicines is medicinal chemistry, where the design and synthesis of novel compounds has led to multiple drugs. Chemical biology, sitting at the interface of many disciplines, has now emerged as a major contributor to the understanding of biological systems and is becoming an integral part of drug discovery. Bringing chemistry and biology much closer and blurring the boundaries between disciplines is creating new opportunities to probe and understand biology; both disciplines play key roles and need to join forces and work together effectively to synergize their impact. The power of chemical biology will then reach its full potential and drive innovation, leading to the discovery of transformative medicines to treat patients. Advances in cancer biology and drug discovery highlight this potential. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Social Pharmacy and Clinical Pharmacy—Joining Forces

    Directory of Open Access Journals (Sweden)

    Anna Birna Almarsdottir

    2015-12-01

    Full Text Available This commentary seeks to define the areas of social pharmacy and clinical pharmacy to uncover what they have in common and what still sets them apart. Common threats and challenges of the two areas are reviewed in order to understand the forces in play. Forces that still keep clinical and social pharmacy apart are university structures, research traditions, and the management of pharmacy services. There are key (but shrinking differences between clinical and social pharmacy which entail the levels of study within pharmaceutical sciences, the location in which the research is carried out, the choice of research designs and methods, and the theoretical foundations. Common strengths and opportunities are important to know in order to join forces. Finding common ground can be developed in two areas: participating together in multi-disciplinary research, and uniting in a dialogue with internal and external key players in putting forth what is needed for the profession of pharmacy. At the end the question is posed, “What’s in a name?” and we argue that it is important to emphasize what unifies the families of clinical pharmacy and social pharmacy for the benefit of both fields, pharmacy in general, and society at large.

  7. Photon-photon collisions

    International Nuclear Information System (INIS)

    Field, J.H.

    1984-01-01

    The current status, both theoretical and experimental, of two photon collision physics is reviewed with special emphasis on recent experimental results from e + e - storage rings. After a complete presentation of the helicity amplitude formalism for the general process e + e - → Xe + e - , various approximations (transverse photon, Weisaecker Williams) are discussed. Beam polarisation effects and radiative corrections are also briefly considered. A number of specific processes, for which experimental results are now available, are then described. In each case existing theoretical prediction are confronted with experimental results. The processes described include single resonance production, lepton and hadron pair production, the structure functions of the photon, the production of high Psub(T) jets and the total photon photon cross section. In the last part of the review the current status of the subject is summarised and some comments are made on future prospects. These include both extrapolations of current research to higher energy machines (LEP, HERA) as well as a brief mention of both the technical realisation and the physics interest of the real γγ and eγ collisions which may be possible using linear electron colliders in the 1 TeV energy range

  8. Photon-photon collisions

    Energy Technology Data Exchange (ETDEWEB)

    Brodsky, S.J.

    1985-01-01

    The study of photon-photon collisions has progressed enormously, stimulated by new data and new calculational tools for QCD. In the future we can expect precise determinations of ..cap alpha../sub s/ and ..lambda../sup ms/ from the ..gamma..*..gamma.. ..-->.. ..pi../sup 0/ form factor and the photon structure function, as well as detailed checks of QCD, determination of the shape of the hadron distribution amplitudes from ..gamma gamma.. ..-->.. H anti H, reconstruction of sigma/sub ..gamma gamma../ from exclusive channels at low W/sub ..gamma gamma../, definitive studies of high p/sub T/ hadron and jet production, and studies of threshold production of charmed systems. Photon-photon collisions, along with radiative decays of the psi and UPSILON, are ideal for the study of multiquark and gluonic resonances. We have emphasized the potential for resonance formation near threshold in virtually every hadronic exclusive channel, including heavy quark states c anti c c anti c, c anti c u anti u, etc. At higher energies SLC, LEP, ...) parity-violating electroweak effects and Higgs production due to equivalent Z/sup 0/ and W/sup + -/ beams from e ..-->.. eZ/sup 0/ and e ..-->.. nu W will become important. 44 references.

  9. Photon-photon collisions

    International Nuclear Information System (INIS)

    Brodsky, S.J.

    1985-01-01

    The study of photon-photon collisions has progressed enormously, stimulated by new data and new calculational tools for QCD. In the future we can expect precise determinations of α/sub s/ and Λ/sup ms/ from the γ*γ → π 0 form factor and the photon structure function, as well as detailed checks of QCD, determination of the shape of the hadron distribution amplitudes from γγ → H anti H, reconstruction of sigma/sub γγ/ from exclusive channels at low W/sub γγ/, definitive studies of high p/sub T/ hadron and jet production, and studies of threshold production of charmed systems. Photon-photon collisions, along with radiative decays of the psi and UPSILON, are ideal for the study of multiquark and gluonic resonances. We have emphasized the potential for resonance formation near threshold in virtually every hadronic exclusive channel, including heavy quark states c anti c c anti c, c anti c u anti u, etc. At higher energies SLC, LEP, ...) parity-violating electroweak effects and Higgs production due to equivalent Z 0 and W +- beams from e → eZ 0 and e → nu W will become important. 44 references

  10. Collision in space

    Science.gov (United States)

    Ellis, S. R.

    2000-01-01

    On June 25, 1997, the Russian supply spacecraft Progress 234 collided with the Mir space station, rupturing Mir's pressure hull, throwing it into an uncontrolled attitude drift, and nearly forcing evacuation of the station. Like many high-profile accidents, this collision was the consequence of a chain of events leading to the final piloting errors that were its immediate cause. The discussion in this article does not resolve the relative contributions of the actions and decisions in this chain. Neither does it suggest corrective measures, many of which are straightforward and have already been implemented by the National Aeronautics and Space Administration (NASA) and the Russian Space Agency. Rather, its purpose is to identify the human factors that played a pervasive role in the incident. Workplace stress, fatigue, and sleep deprivation were identified by NASA as contributory factors in the Mir-Progress collision (Culbertson, 1997; NASA, forthcoming), but other contributing factors, such as requiring crew to perform difficult tasks for which their training is not current, could potentially become important factors in future situations.

  11. Collisions between Globular Clusters

    Science.gov (United States)

    Belloni, D. T.; Rocha-Pinto, H. J.

    2014-10-01

    The study of globular clusters (GC) plays an important role in our understanding of the Universe since these systems are true laboratories for theories of stellar dynamics and evolution. We are interested in studying a globular cluster formed by a collision between two different GC with NBODY6 (Aarseth, 2003). Firstly, in order to understand this code, we analyse how tidal streams form from a globular cluster in a circular orbit (on the disk) around the center of the Milky Way. In the next stage of this work we will study that collision. The stellar escape or capture from globular cluster can be understood with the Restricted Three Body Problem. These stars escape in a chaotic orbit, and in some cases may return (again in a chaotic orbit) to the cluster due to the Galactic potential. In most cases, such stars quickly alter their escape chaotic orbits to orbits that are similar to the parent cluster's orbit. Our results show an agglomeration of stars in a normal direction related to the direction towards the center of the Milky Way, forming thus a stream. We can explain this considering that a circular orbit around the dominant potential is the most likely orbit, since it requires minimum energy. In this coordinate systems, the tidal tails (or streams) rotates around the cluster center with the same mean motion associated to cluster around the Milky Way center.

  12. A Changing Wind Collision

    Science.gov (United States)

    Nazé, Yaël; Koenigsberger, Gloria; Pittard, Julian M.; Parkin, Elliot Ross; Rauw, Gregor; Corcoran, Michael F.; Hillier, D. John

    2018-02-01

    We report on the first detection of a global change in the X-ray emitting properties of a wind–wind collision, thanks to XMM-Newton observations of the massive Small Magellenic Cloud (SMC) system HD 5980. While its light curve had remained unchanged between 2000 and 2005, the X-ray flux has now increased by a factor of ∼2.5, and slightly hardened. The new observations also extend the observational coverage over the entire orbit, pinpointing the light-curve shape. It has not varied much despite the large overall brightening, and a tight correlation of fluxes with orbital separation is found without any hysteresis effect. Moreover, the absence of eclipses and of absorption effects related to orientation suggests a large size for the X-ray emitting region. Simple analytical models of the wind–wind collision, considering the varying wind properties of the eruptive component in HD 5980, are able to reproduce the recent hardening and the flux-separation relationship, at least qualitatively, but they predict a hardening at apastron and little change in mean flux, contrary to observations. The brightness change could then possibly be related to a recently theorized phenomenon linked to the varying strength of thin-shell instabilities in shocked wind regions. Based on XMM-Newton and Chandra data.

  13. Crash energy absorption of two-segment crash box with holes under frontal load

    Science.gov (United States)

    Choiron, Moch. Agus; Sudjito, Hidayati, Nafisah Arina

    2016-03-01

    Crash box is one of the passive safety components which designed as an impact energy absorber during collision. Crash box designs have been developed in order to obtain the optimum crashworthiness performance. Circular cross section was first investigated with one segment design, it rather influenced by its length which is being sensitive to the buckling occurrence. In this study, the two-segment crash box design with additional holes is investigated and deformation behavior and crash energy absorption are observed. The crash box modelling is performed by finite element analysis. The crash test components were impactor, crash box, and fixed rigid base. Impactor and the fixed base material are modelled as a rigid, and crash box material as bilinear isotropic hardening. Crash box length of 100 mm and frontal crash velocity of 16 km/jam are selected. Crash box material of Aluminum Alloy is used. Based on simulation results, it can be shown that holes configuration with 2 holes and ¾ length locations have the largest crash energy absorption. This condition associated with deformation pattern, this crash box model produces axisymmetric mode than other models.

  14. Emotional reactions in patients after frontal lobe stroke

    Directory of Open Access Journals (Sweden)

    Stojanović Zlatan

    2015-01-01

    Full Text Available Background/Aim. Emotional reactions have been documented after tumor lesions and the other damages of the brain. The aim of this paper was to examine the correlation between frontal lobe lesions and emotional reactions in patients with stroke. Methods. The research included 118 patients after stroke. Lesion localization was defined on computed axial tomography records, whereas the area and perimeter of lesion were measured by AutoCAD 2004 software. Examinations by means of the Hamilton Rating Scale for Anxiety and Depression (HRSA and HRSD were carried out 11-40 days after stroke. Statistic data were processed by simple linear/nonlinear regression, Cox's and the generalized linear model. Results. A higher frequency of emotional reactions, i.e. anxiety, was determined in women after stroke (p = 0.024. A negative correlation between the lesion size and the intensity of anxiety manifestations was determined (Spearman’s r = -0.297; p = 0.001. Anxiety was more frequent in patients with frontal lobe lesions in the dominant hemisphere (interaction: frontal lesion * hand dominant hemisphere, p = 0.017. Also, HRSD score values showed the tendency for lesser decline in case of greater frontal lobe lesions in relation to lesions of other regions of prosencephalon (interaction: frontal lesion * lesion area, p = 0.001. Conclusion. The results of this study indicate the correlation between evolutionary younger structures of the central nervous system and emotional reactions of man. Therefore, it is necessary to undertake proper early psychopharmacotherapy in the vulnerable group of patients.

  15. Differences in the neural correlates of frontal lobe tests.

    Science.gov (United States)

    Matsuoka, Teruyuki; Kato, Yuka; Imai, Ayu; Fujimoto, Hiroshi; Shibata, Keisuke; Nakamura, Kaeko; Yamada, Kei; Narumoto, Jin

    2018-01-01

    The Executive Interview (EXIT25), the executive clock-drawing task (CLOX1), and the Frontal Assessment Battery (FAB) are used to assess executive function at the bedside. These tests assess distinct psychometric properties. The aim of this study was to examine differences in the neural correlates of the EXIT25, CLOX1, and FAB based on magnetic resonance imaging. Fifty-eight subjects (30 with Alzheimer's disease, 10 with mild cognitive impairment, and 18 healthy controls) participated in this study. Multiple regression analyses were performed to examine the brain regions correlated with the EXIT25, CLOX1, and FAB scores. Age, gender, and years of education were included as covariates. Statistical thresholds were set to uncorrected P-values of 0.001 at the voxel level and 0.05 at the cluster level. The EXIT25 score correlated inversely with the regional grey matter volume in the left lateral frontal lobe (Brodmann areas 6, 9, 44, and 45). The CLOX1 score correlated positively with the regional grey matter volume in the right orbitofrontal cortex (Brodmann area 11) and the left supramarginal gyrus (Brodmann area 40). The FAB score correlated positively with the regional grey matter volume in the right precentral gyrus (Brodmann area 6). The left lateral frontal lobe (Brodmann area 9) and the right lateral frontal lobe (Brodmann area 46) were identified as common brain regions that showed association with EXIT25, CLOX1, and FAB based only a voxel-level threshold. The results of this study suggest that the EXIT25, CLOX1, and FAB may be associated with the distinct neural correlates of the frontal cortex. © 2018 Japanese Psychogeriatric Society.

  16. Sixteenth International Conference on the physics of electronic and atomic collisions

    Energy Technology Data Exchange (ETDEWEB)

    Dalgarno, A.; Freund, R.S.; Lubell, M.S.; Lucatorto, T.B. (eds.)

    1989-01-01

    This report contains abstracts of papers on the following topics: photons, electron-atom collisions; electron-molecule collisions; electron-ion collisions; collisions involving exotic species; ion- atom collisions, ion-molecule or atom-molecule collisions; atom-atom collisions; ion-ion collisions; collisions involving rydberg atoms; field assisted collisions; collisions involving clusters and collisions involving condensed matter.

  17. Sixteenth International Conference on the physics of electronic and atomic collisions

    International Nuclear Information System (INIS)

    Dalgarno, A.; Freund, R.S.; Lubell, M.S.; Lucatorto, T.B.

    1989-01-01

    This report contains abstracts of papers on the following topics: photons, electron-atom collisions; electron-molecule collisions; electron-ion collisions; collisions involving exotic species; ion- atom collisions, ion-molecule or atom-molecule collisions; atom-atom collisions; ion-ion collisions; collisions involving rydberg atoms; field assisted collisions; collisions involving clusters and collisions involving condensed matter

  18. Modified Cranialization and Secondary Cranioplasty for Frontal Sinus Infection after Craniotomy: Technical Note

    Science.gov (United States)

    YOSHIOKA, Nobutaka

    2014-01-01

    Frontal sinus infection after incorrect treatment of an opened frontal sinus may require extended approaches. This article aims to introduce modified cranialization technique and secondary cranioplasty for frontal sinus infection involving the frontal sinus outflow tract after craniotomy. Eight patients with delayed onset frontal sinus infection involving frontal outflow tract after craniotomy were treated from 2008 to 2012. Debridement and cranialization involving the elimination of the frontal outflow tract was performed. Unilateral sinus cranialization combined with reduction of the non-affected contralateral sinus was carried out for the patients with unilateral sinusitis. A pericranial-frontalis muscle flap was used to separate the intracranial and extracranial spaces. Secondary cranioplasty with hydroxyapatite was performed approximately 3 months after the cranialization. The patients’ original conditions included brain tumors (n = 3), frontal sinus fractures (n = 2), and subarachnoid hemorrhage (n = 3). The mean interval between the initial treatment and the onset of sinus infection was 23 years. The frontal sinus infection was bilateral in six cases and unilateral in two cases. Frontal sinus outflow tract was involved in sinus infection in every case. None of the patients suffered recurrent rhinogenic infections within the follow-up period (mean = 35 months) after the secondary cranioplasty. Aesthetic results were satisfactory in every case. Modified cranialization involving elimination of the frontal outflow tract is an alternative method for the patients with pathology in the frontal outflow tract after frontal craniotomy. Secondary cranioplasty provides an esthetically pleasing appearance in such cases. PMID:25169030

  19. The Frontal Lobe Score: part II: evaluation of its clinical validity.

    Science.gov (United States)

    Wildgruber, D; Kischka, U; Fassbender, K; Ettlin, T M

    2000-06-01

    To evaluate the ability of the Frontal Lobe Score (FLS) to differentiate patients with frontal lobe lesions from those with nonfrontal lesions and normal controls. In a prospective, blind setup, the sensitivity and specificity of the Frontal Lobe Score was compared with the Wisconsin Card Sorting Test (WCST) and the Stroop Test. A sample of 108 subjects (26 patients with cerebral lesions confined to the frontal lobes, 28 patients with cerebral lesions without involvement of the frontal lobes, 31 patients with mixed frontal/nonfrontal lesions, 23 controls without cerebral lesions) was examined. Frontal Lobe Score, Wisconsin Card Sorting Test, Stroop Test. The Frontal Lobe Score detected pure frontal lesions with a sensitivity of 92.3%. It discriminated patients with frontal lesions from normal controls with a specificity of 100%; differentiation from patients with nonfrontal lesions was obtained with a specificity of 75.0%. For the WCST, sensitivity for detection of pure frontal lesions was 65.4%, while specificity was 60.9% compared with normal controls and 53.6% compared with nonfrontal lesions. The Stroop Test showed a sensitivity of 30.8%, a specificity compared with normal controls of 95.7% and compared with nonfrontal lesions of 92.9%. The Frontal Lobe Score has clinical usefulness for screening of effects of frontal lobe damage superior to that of the WCST and the Stroop Test.

  20. Infrared transient-liquid-phase joining of SCS-6/{beta}21S titanium matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Blue, C.A.; Sikka, V.K. [Oak Ridge National Lab., TN (United States). Materials Processing Group; Blue, R.A.; Lin, R.Y. [Univ. of Cincinnati, OH (United States). Dept. of Materials Science and Engineering

    1996-02-01

    Fiber-reinforced titanium matrix composites (TMCs) are among the advanced materials being considered for use in the aerospace industry due to their light weight, high strength, and high modulus. A rapid infrared joining process has been developed for the joining of composites and advanced materials. Rapid infrared joining has been shown not to have many of the problems associated with conventional joining methods. Two models were utilized to predict the joint evolution and fiber reaction zone growth. TMC, 16-ply SCS-6/{beta}21S, has been successfully joined with total processing times of under 2 min utilizing the rapid infrared joining technique. The process utilizes a 50 C/sec ramping rate, 17-{micro}m Ti-15Cu-15Ni wt % filler material between the faying surfaces; a joining temperature of 1,100 C; and 120 sec of time to join the composite material. Joint shear strength testing of the rapid infrared joints at temperatures as high as 800 C has revealed no joint failures. Also, due to the rapid cooling of the process, no poststabilization of the matrix material is necessary to prevent the formation of a brittle omega phase during subsequent use of the TMC at intermediate temperatures, 270 to 430 C, for up to 20 h.

  1. On a possible empirical meaning of meets and joins for quantum propositions

    Science.gov (United States)

    Herbut, Fedor

    1984-09-01

    Following up an idea of Jauch, an empirical basis is worked out for the meets (and joins) of quantum propositions through approximate measurement to an arbitrary degree of accuracy of special yes-no effects constructed from chains of yes-no measurements. This is done with a view to interpreting the meets (and joins) as Dedekind's cuts in analogy with irrationals.

  2. On a possible empirical meaning of meets and joins for quantum propositions

    International Nuclear Information System (INIS)

    Herbut, F.

    1984-01-01

    Following up an idea of Jauch, an empirical basis is worked out for the meets (and joins) of quantum propositions through approximate measurement to an arbitrary degree of accuracy of special yes-no effects constructed from chains of yes-no measurements. This is done with a view to interpreting the meets (and joins) as Dedekind's cuts in analogy with irrationals. (orig.)

  3. Investigating the Pulse Mode Laser Joining of Overlapped Plastic and Metal Sheets

    Science.gov (United States)

    Bauernhuber, Andor; Markovits, Tamás; Takács, János

    The growing utilization of plastic materials in our devices calls for joining them with traditional, often applied structural materials, like metals. Laser assisted metal plastic joining can be used to solve the problem mentioned above, however, relatively few materials have been investigated which could be used to create this special joint. In the course of this research, authors used pulse mode Nd:YAG laser source, structural steel and poly(methyl methacrylate) to create joining between rarely examined material pairs so far, and to explore the effects of technological settings like laser pulse shape, laser spot size, welding speed and joint strength. Material surfaces were also modified (sand blasting,) to enhance joint properties. In plastic material during joining and torn surfaces were investigated. Joints with good strength results were prepared to enable further research on transparent-absorbent metal plastic joining.

  4. Joining of SiCf/SiC composites for thermonuclear fusion reactors

    International Nuclear Information System (INIS)

    Ferraris, M.; Badini, C.; Montorsi, M.; Appendino, P.; Scholz, H.W.

    1994-01-01

    Due to their favourable radiological behaviour, SiC f /SiC composites are promising structural materials for future use in fusion reactors. A problem to cope with is the joining of the ceramic composite material (CMC) to itself for more complex structures. Maintenance concepts for a reactor made of SiC f /SiC will demand a method of joining. The joining agents should comply with the low-activation approach of the base material. With the acceptable elements Si and Mg, sandwich structures of composite/metal/composite were prepared in Ar atmosphere at temperatures just above the melting points of the metals. Another promising route is the use of joining agents of boro-silicate glasses: their composition can be tailored to obtain softening temperatures of interest for fusion applications. The glassy joint can be easily ceramised to improve thermomechanical properties. The joining interfaces were investigated by SEM-EDS, XRD and mechanical tests. ((orig.))

  5. Effects of joining conditions on the structures and properties of joints of REBCO coated conductors

    Science.gov (United States)

    Maebatake, T.; Mori, N.; Teranishi, R.; Mukaida, M.; Yamada, K.; Miura, M.; Yoshizumi, M.; Izumi, T.

    2010-11-01

    We investigated the joining of two REBCO (REBa2Cu3O7-X, RE = Y, Gd) coated conductors using the diffusion joint process. REBCO coated conductors with stabilizing silver layer were joined by various joining conditions. Two pieces of the silver layer of tapes were overlapped in a face to face manner. Then, the pieces were pressurized and heat-treated at about 623-673 K under a pressure using some weights in oxygen atmosphere. Finally, the joint resistivity was obtained as low as about 10 nΩ cm2 by 10 MPa for YBCO tape. The joint resistivity of the GdBCO tape was 50-60 nΩ cm2, which was higher than YBCO, but improved to 37 nΩ cm2 at 10 MPa by improving the joining conditions. Influences of joining conditions such as pressure and evenness of specimens and holders were investigated on joint adhesion and resistivity.

  6. The role of frontal EEG asymmetry in post-traumatic stress disorder

    NARCIS (Netherlands)

    Meyer, T.; Smeets, T.J.M.; Giesbrecht, T.; Quaedflieg, C.W.E.M.; Smulders, F.T.Y.; Meijer, E.H.; Merckelbach, H.L.G.J.

    2015-01-01

    Frontal alpha asymmetry, a biomarker derived from electroencephalography (EEG) recordings, has often been associated with psychological adjustment, with more left-sided frontal activity predicting approach motivation and lower levels of depression and anxiety. This suggests high relevance to

  7. Global NOAA CoastWatch Chlorophyll Frontal Product from MODIS/Aqua (NCEI Accession 0110333)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — MODIS/Aqua chlorophyll frontal products: the NOAA Okeanos operational production system produces near real-time chlorophyll frontal products (magnitude and...

  8. Gyrokinetic linearized Landau collision operator

    DEFF Research Database (Denmark)

    Madsen, Jens

    2013-01-01

    , which is important in multiple ion-species plasmas. Second, the equilibrium operator describes drag and diffusion of the magnetic field aligned component of the vorticity associated with the E×B drift. Therefore, a correct description of collisional effects in turbulent plasmas requires the equilibrium......The full gyrokinetic electrostatic linearized Landau collision operator is calculated including the equilibrium operator, which represents the effect of collisions between gyrokinetic Maxwellian particles. First, the equilibrium operator describes energy exchange between different plasma species...... operator, even for like-particle collisions....

  9. Atomic collisions involving pulsed positrons

    DEFF Research Database (Denmark)

    Merrison, J. P.; Bluhme, H.; Field, D.

    2000-01-01

    Conventional slow positron beams have been widely and profitably used to study atomic collisions and have been instrumental in understanding the dynamics of ionization. The next generation of positron atomic collision studies are possible with the use of charged particle traps. Not only can large...... instantaneous intensities be achieved with in-beam accumulation, but more importantly many orders of magnitude improvement in energy and spatial resolution can be achieved using positron cooling. Atomic collisions can be studied on a new energy scale with unprecedented precion and control. The use...

  10. Erosion dynamics of powder snow avalanches - model of frontal entrainment

    Science.gov (United States)

    Louge, Michel; Sovilla, Betty

    2013-04-01

    We analyze entrainment at the head of powder snow avalanches (PSA) behaving as an eruption current. Instead of invoking an erosion model or other fitted parameters, the analysis assumes that erosion is sustained by a massive blow-out arising as the snow cover is fluidized by the very pore pressure gradients that the avalanche induces within the snow pack. The stability of a mass balance involving snow cover and flow in the PSA's head region then sets frontal speed, height, mixed-mean density, snowpack fluidization depth, frontal impact pressure and static pressure. We show that acceleration of the front is insensitive to local slope, but effectively depends on the rate of change in cloud width. We compare predictions with data collected at the Vallee de la Sionne.

  11. Trauma in Facial Plastic Surgery: Frontal Sinus Fractures.

    Science.gov (United States)

    Kim, Irene A; Boahene, Kofi D; Byrne, Patrick J

    2017-11-01

    The optimal management of frontal sinus fractures remains controversial. Fortunately, the severity of these injuries has diminished with more stringent auto-safety regulations, changing the treatment paradigms used to repair these injuries. Appropriate patient selection and close follow-up may allow for conservative management strategies when dealing with frontal sinus fractures, largely replacing the more morbid and invasive techniques that have been the mainstay for years. Because acute and delayed sequelae can arise after the initial injury, patients should be thoroughly counseled about the importance of follow-up and the need to seek medical care if they develop any concerning signs or symptoms. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. Frontal destabilization of Stonebreen, Edgeøya, Svalbard

    Directory of Open Access Journals (Sweden)

    T. Strozzi

    2017-02-01

    and synthetic aperture radar (SAR satellite data, a number of zones of velocity increases have been observed at formerly slow-flowing calving fronts on Svalbard. Here we present the dynamic evolution of the southern lobe of Stonebreen on Edgeøya. We observe a slowly steady retreat of the glacier front from 1971 until 2011, followed by a strong increase in ice surface velocity along with a decrease of volume and frontal extension since 2012. The considerable losses in ice thickness could have made the tide-water calving glacier, which is grounded below sea level some 6 km inland from the 2014 front, more sensitive to surface meltwater reaching its bed and/or warm ocean water increasing frontal ablation with subsequent strong multi-annual ice-flow acceleration.

  13. Ground-glass pattern fibrous dysplasia of frontal sinus.

    Science.gov (United States)

    Chourmouzi, D; Psoma, E; Drevelegas, A

    2013-01-01

    The case of a 5-year-old boy with ground-glass pattern craniofacial fibrous dysplasia (FD) presenting with progressive swelling in the right frontal region is reported. The imaging findings with computed tomography and magnetic resonance imaging (MRI) findings are presented. The differential diagnosis with inspissated mucocele is discussed as well. Fibrous tissue could be hypo dense on CT. Post-contrast enhancement of the lesion on MRI is the key for diagnosis.

  14. [Fibrous dysplasia of the frontal sinus: a case report].

    Science.gov (United States)

    Keleş, Erol; Kaplama, Mehmet Erkan; Ozkara, Sule; Cobanoğlu, Bengü

    2011-01-01

    Fibrous dysplasia is a rare and indolent benign tumor of bone. Although it is a benign tumor, it has malignant transformation potential. Fibrous dysplasia can involve a single or multiple bones. The maxilla and mandible are the most common sites in the head and neck region. Paranasal sinus involvement is rare. Surgical excision is the preferred treatment of patients with symptomatic fibrous dysplasia. In this article, a 54-year-old male patient diagnosed with fibrous dysplasia of the frontal bone is presented.

  15. Frontal networks in adults with autism spectrum disorder.

    Science.gov (United States)

    Catani, Marco; Dell'Acqua, Flavio; Budisavljevic, Sanja; Howells, Henrietta; Thiebaut de Schotten, Michel; Froudist-Walsh, Seán; D'Anna, Lucio; Thompson, Abigail; Sandrone, Stefano; Bullmore, Edward T; Suckling, John; Baron-Cohen, Simon; Lombardo, Michael V; Wheelwright, Sally J; Chakrabarti, Bhismadev; Lai, Meng-Chuan; Ruigrok, Amber N V; Leemans, Alexander; Ecker, Christine; Consortium, Mrc Aims; Craig, Michael C; Murphy, Declan G M

    2016-02-01

    It has been postulated that autism spectrum disorder is underpinned by an 'atypical connectivity' involving higher-order association brain regions. To test this hypothesis in a large cohort of adults with autism spectrum disorder we compared the white matter networks of 61 adult males with autism spectrum disorder and 61 neurotypical controls, using two complementary approaches to diffusion tensor magnetic resonance imaging. First, we applied tract-based spatial statistics, a 'whole brain' non-hypothesis driven method, to identify differences in white matter networks in adults with autism spectrum disorder. Following this we used a tract-specific analysis, based on tractography, to carry out a more detailed analysis of individual tracts identified by tract-based spatial statistics. Finally, within the autism spectrum disorder group, we studied the relationship between diffusion measures and autistic symptom severity. Tract-based spatial statistics revealed that autism spectrum disorder was associated with significantly reduced fractional anisotropy in regions that included frontal lobe pathways. Tractography analysis of these specific pathways showed increased mean and perpendicular diffusivity, and reduced number of streamlines in the anterior and long segments of the arcuate fasciculus, cingulum and uncinate--predominantly in the left hemisphere. Abnormalities were also evident in the anterior portions of the corpus callosum connecting left and right frontal lobes. The degree of microstructural alteration of the arcuate and uncinate fasciculi was associated with severity of symptoms in language and social reciprocity in childhood. Our results indicated that autism spectrum disorder is a developmental condition associated with abnormal connectivity of the frontal lobes. Furthermore our findings showed that male adults with autism spectrum disorder have regional differences in brain anatomy, which correlate with specific aspects of autistic symptoms. Overall these

  16. Responses of primate frontal cortex neurons during natural vocal communication

    OpenAIRE

    Miller, Cory T.; Thomas, A. Wren; Nummela, Samuel U.; de la Mothe, Lisa A.

    2015-01-01

    The role of primate frontal cortex in vocal communication and its significance in language evolution have a controversial history. While evidence indicates that vocalization processing occurs in ventrolateral prefrontal cortex neurons, vocal-motor activity has been conjectured to be primarily subcortical and suggestive of a distinctly different neural architecture from humans. Direct evidence of neural activity during natural vocal communication is limited, as previous studies were performed ...

  17. Distinct frontal lobe morphology in girls and boys with ADHD.

    Science.gov (United States)

    Dirlikov, Benjamin; Shiels Rosch, Keri; Crocetti, Deana; Denckla, Martha B; Mahone, E Mark; Mostofsky, Stewart H

    2015-01-01

    This study investigated whether frontal lobe cortical morphology differs for boys and girls with ADHD (ages 8-12 years) in comparison to typically developing (TD) peers. Participants included 226 children between the ages of 8-12 including 93 children with ADHD (29 girls) and 133 TD children (42 girls) for which 3T MPRAGE MRI scans were obtained. A fully automated frontal lobe atlas was used to generate functionally distinct frontal subdivisions, with surface area (SA) and cortical thickness (CT) assessed in each region. Analyses focused on overall diagnostic differences as well as examinations of the effect of diagnosis within boys and girls. Girls, but not boys, with ADHD showed overall reductions in total prefrontal cortex (PFC) SA. Localization revealed that girls showed widely distributed reductions in the bilateral dorsolateral PFC, left inferior lateral PFC, right medial PFC, right orbitofrontal cortex, and left anterior cingulate; and boys showed reduced SA only in the right anterior cingulate and left medial PFC. In contrast, boys, but not girls, with ADHD showed overall reductions in total premotor cortex (PMC) SA. Further localization revealed that in boys, premotor reductions were observed in bilateral lateral PMC regions; and in girls reductions were observed in bilateral supplementary motor complex. In line with diagnostic group differences, PMC and PFC SAs were inversely correlated with symptom severity in both girls and boys with ADHD. These results elucidate sex-based differences in cortical morphology of functional subdivisions of the frontal lobe and provide additional evidence of associations among SA and symptom severity in children with ADHD.

  18. Semantic memory and frontal executive function during transient global amnesia.

    OpenAIRE

    Hodges, J R

    1994-01-01

    To assess semantic memory and frontal executive function, two patients underwent neuropsychological testing during transient global amnesia (TGA) and after an interval of 6-8 weeks. In spite of a profound deficit in anterograde verbal and non-verbal memory, semantic memory was normal, as judged by category fluency measures, picture naming, and picture-word and picture-picture matching, and reading ability was normal. Similarly, there were no deficits on a number of tests known to be sensitive...

  19. Frontal midline theta oscillations during mental arithmetic: effects of stress

    OpenAIRE

    Gärtner, Matti; Grimm, Simone; Bajbouj, Malek

    2015-01-01

    Complex cognitive tasks such as mental arithmetic heavily rely on intact, well-coordinated prefrontal cortex (PFC) function. Converging evidence suggests that frontal midline theta (FMT) oscillations play an important role during the execution of such PFC-dependent tasks. Additionally, it is well-established that acute stress impairs PFC function, and recent evidence suggests that FMT is decreased under stress. In this EEG study, we investigated FMT oscillations during a mental arithmetic tas...

  20. Frontal lobe seizures: from clinical semiology to localization.

    Science.gov (United States)

    Bonini, Francesca; McGonigal, Aileen; Trébuchon, Agnès; Gavaret, Martine; Bartolomei, Fabrice; Giusiano, Bernard; Chauvel, Patrick

    2014-02-01

    Frontal lobe seizures are difficult to characterize according to semiologic and electrical features. We wished to establish whether different semiologic subgroups can be identified and whether these relate to anatomic organization. We assessed all seizures from 54 patients with frontal lobe epilepsy that were explored with stereoelectroencephalography (SEEG) during presurgical evaluation. Semiologic features and concomitant intracerebral EEG changes were documented and quantified. These variables were examined using Principal Component Analysis and Cluster Analysis, and semiologic features correlated with anatomic localization. Four main groups of patients were identified according to semiologic features, and correlated with specific patterns of anatomic seizure localization. Group 1 was characterized clinically by elementary motor signs and involved precentral and premotor regions. Group 2 was characterized by a combination of elementary motor signs and nonintegrated gestural motor behavior, and involved both premotor and prefrontal regions. Group 3 was characterized by integrated gestural motor behavior with distal stereotypies and involved anterior lateral and medial prefrontal regions. Group 4 was characterized by seizures with fearful behavior and involved the paralimbic system (ventromedial prefrontal cortex ± anterior temporal structures). The groups were organized along a rostrocaudal axis, representing bands within a spectrum rather than rigid categories. The more anterior the seizure organization, the more likely was the occurrence of integrated behavior during seizures. Distal stereotypies were associated with the most anterior prefrontal localizations, whereas proximal stereotypies occurred in more posterior prefrontal regions. Meaningful categorization of frontal seizures in terms of semiology is possible and correlates with anatomic organization along a rostrocaudal axis, in keeping with current hypotheses of frontal lobe hierarchical organization

  1. Chondromyxoid fibroma of the frontal bone in a teenager

    Energy Technology Data Exchange (ETDEWEB)

    Kadom, Nadja [Children' s National Medical Center, Department of Radiology, Division of Neuroradiology, Washington, DC (United States); Rushing, Elisabeth J. [Armed Forces Institute of Pathology, Washington, DC (United States); Yaun, Amanda [Children' s National Medical Center, Division of Neurosurgery, Washington, DC (United States); Santi, Mariarita [Children' s National Medical Center, Division of Neuropathology, Washington, DC (United States)

    2009-01-15

    We report a skull chondromyxoid fibroma with symptomatic intracranial extension causing initial misdiagnosis as a psychiatric disorder in a 14-year-old child. CT performed for work-up of the patient's ''stuffy nose'' revealed a large calcified frontal bone mass with extensive intracranial growth. We present this child with the diagnosis of intracranial chondromyxoid fibroma with detailed neuroimaging and neuropathology correlations. (orig.)

  2. Finite element modelling of helmeted head impact under frontal ...

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... Finite element models of the head and helmet were used to study contact forces during frontal impact of the head with a rigid surface. The finite element model of the head consists of skin, skull, cerebro-spinal fluid (CSF), brain, tentorium and falx. The finite element model of the helmet consists of shell and ...

  3. Orbital Cystic Schwannoma Originating from the Frontal Nerve

    Directory of Open Access Journals (Sweden)

    Yasuhiko Hayashi

    2012-01-01

    Full Text Available Schwannomas of the orbit are very rare benign neoplasms. Intraorbital cystic schwannomas originating from the frontal nerve are even rarer, with only 1 case reported to date. This is most likely due to the fact that, in most cases, the origin of the orbital schwannoma cannot be identified intraoperatively. The nerve origin is usually speculated from histological examination of the specimen and the postoperative neurological deficits of the patient. Here, we present the case of a 65-year-old woman with a one-month history of exophthalmos, whose orbital cystic lesion was completely removed by microsurgical transcranial operation. Intraoperatively, the continuity between the tumor and frontal nerve was seen macroscopically, leading us to confirm the frontal nerve as an origin of the tumor, which was consistent with the postoperative neurological findings. The diagnosis of the tumor was established as schwannoma from the histological examination. As a differential diagnosis of the orbital cystic lesions, the possibility of schwannomas should be kept in mind.

  4. Relationships between foot type and dynamic rearfoot frontal plane motion

    Directory of Open Access Journals (Sweden)

    Chuter Vivienne H

    2010-06-01

    Full Text Available Abstract Background The Foot Posture Index (FPI provides an easily applicable, validated method for quantifying static foot posture. However there is limited evidence relating to the ability of the FPI to predict dynamic foot function. This study aimed to assess the relationship between dynamic rearfoot motion and FPI scores in pronated and normal foot types. Methods 40 participants were recruited with equal numbers of pronated and normal foot types as classified by their FPI score. Three dimensional rearfoot motion was collected for each of the participants. Dynamic maximum rearfoot eversion was correlated with the total FPI score across all participants and within the normal and pronated foot types. Linear correlations were performed between components of the total FPI scores measuring frontal plane rearfoot position and maximum rearfoot eversion. The capacity of the total FPI score to predict maximum frontal plane motion of the rearfoot was investigated using linear regression analysis. Results The correlation between the total FPI score and maximum rearfoot eversion was strongly positive (r = 0.92, p 2 = 0.85, p Conclusions The results of this study suggest the FPI has strong predictive ability for dynamic rearfoot function. This will assist in clinical screening and research by allowing easy classification by functional foot type. Positive correlations between frontal plane rearfoot measurements and maximum rearfoot eversion suggest the FPI may identify dominant planar components of dynamic rearfoot motion and warrants further investigation.

  5. Music increases frontal EEG coherence during verbal learning.

    Science.gov (United States)

    Peterson, David A; Thaut, Michael H

    2007-02-02

    Anecdotal and some empirical evidence suggests that music can enhance learning and memory. However, the mechanisms by which music modulates the neural activity associated with learning and memory remain largely unexplored. We evaluated coherent frontal oscillations in the electroencephalogram (EEG) while subjects were engaged in a modified version of Rey's Auditory Verbal Learning Test (AVLT). Subjects heard either a spoken version of the AVLT or the conventional AVLT word list sung. Learning-related changes in coherence (LRCC) were measured by comparing the EEG during word encoding on correctly recalled trials to the immediately preceding trial on which the same word was not recalled. There were no significant changes in coherence associated with conventional verbal learning. However, musical verbal learning was associated with increased coherence within and between left and right frontal areas in theta, alpha, and gamma frequency bands. It is unlikely that the different patterns of LRCC reflect general performance differences; the groups exhibited similar learning performance. The results suggest that verbal learning with a musical template strengthens coherent oscillations in frontal cortical networks involved in verbal encoding.

  6. Frontal and striatal alterations associated with psychopathic traits in adolescents

    Science.gov (United States)

    Yang, Yaling; Narr, Katherine L.; Baker, Laura A.; Joshi, Shantanu H.; Jahanshad, Neda; Raine, Adrian; Thompson, Paul M.

    2016-01-01

    Neuroimaging research has demonstrated a range of structural deficits in adults with psychopathy, but little is known about structural correlates of psychopathic tendencies in adolescents. Here we examined structural magnetic resonance imaging (sMRI) data obtained from 14-year-old adolescents (n=108) using tensor-based morphometry (TBM) to isolate global and localized differences in brain tissue volumes associated with psychopathic traits in this otherwise healthy developmental population. We found that greater levels of psychopathic traits were correlated with increased brain tissue volumes in the left putamen, left ansa peduncularis, right superiomedial prefrontal cortex, left inferior frontal cortex, right orbitofrontal cortex, and right medial temporal regions and reduced brain tissues volumes in the right middle frontal cortex, left superior parietal lobule, and left inferior parietal lobule. Post hoc analyses of parcellated regional volumes also showed putamen enlargements to correlate with increased psychopathic traits. Consistent with earlier studies, findings suggest poor decision-making and emotional dysregulation associated with psychopathy may be due, in part, to structural anomalies in frontal and temporal regions whereas striatal structural variations may contribute to sensation-seeking and reward-driven behavior in psychopathic individuals. Future studies will help clarify how disturbances in brain maturational processes might lead to the developmental trajectory from psychopathic tendencies in adolescents to adult psychopathy. PMID:25676553

  7. Joined up Clinical Governance: Learning from Our Mistakes

    Directory of Open Access Journals (Sweden)

    Pam Mosedale

    2017-02-01

    Full Text Available This session will be a practical demonstration, with group discussion of how a significant event can lead to the practice examining what happened, looking at the evidence base, revising protocols & auditing implementation of the new protocols.A significant event is an event thought by anyone in the team to be significant in the care of patients or the conduct of the practice.Significant Event Audit is a qualitative rather than quantitative form of Audit but still needs a structured framework to be successful.SEA involves gathering information in the form of a timeline of the event, clinical records & accounts of individuals involved.Scenarios around significant events will be discussed and analysed by the group as if they were conducting a non-threatening, open, fair & honest SEA meeting.During the meeting the incident will be analysed to see what happened, why it happened, any underlying reasons, what has been learned & what needs to change. This meeting is not to apportion blame.When looking at what needs to change the group should consider whether it is necessary to go away & look at the evidence base & then make changes to practice protocols. Any need for training or CPD for individuals or the whole team should be identified.A timescale for changes should be agreed.An audit can then be carried out to monitor the improvements and assess the impact of these changes. The group will consider what audits are appropriate, whether process or outcome audits are useful in the circumstances. They will also discuss how these audits can be carried out.SEA is a very useful tool in veterinary practice & a very good way to get all team members engaged with clinical governance & evidence based veterinary medicine in a joined up way which demonstrates the potential improvements to practice systems of work and patient care and safety.This session would be designed to appeal to all team members whether vets, nurses, receptionists or practice managers.

  8. Collision attack against Tav-128 hash function

    Science.gov (United States)

    Hariyanto, Fajar; Hayat Susanti, Bety

    2017-10-01

    Tav-128 is a hash function which is designed for Radio Frequency Identification (RFID) authentication protocol. Tav-128 is expected to be a cryptographically secure hash function which meets collision resistance properties. In this research, a collision attack is done to prove whether Tav-128 is a collision resistant hash function. The results show that collisions can be obtained in Tav-128 hash function which means in other word, Tav-128 is not a collision resistant hash function.

  9. Collision Technologies for Circular Colliders

    Science.gov (United States)

    Levichev, Eugene

    2015-02-01

    For several decades already, particle colliders have been essential tools for particle physics. From the very beginning, such accelerators have been among the most complicated scientific instruments ever built, including a number of innovative technological developments. Examples are ultrahigh vacuum systems, magnets with a very high magnetic field, and equipment for sub-ns synchronization and sub-mm precision alignment of equipment inside multi-km underground tunnels. Some key technologies are related to the focusing of the beam down to a scale of sub-μm at the collision point to obtain high luminosity. This review provides an overview of collision concepts and technologies for circular particle colliders, starting from the first ideas. In particular, it discusses such novel schemes and related technologies as crab waist collision and round beam collision.

  10. Collision Risk Analysis for HSC

    DEFF Research Database (Denmark)

    Urban, Jesper; Pedersen, Preben Terndrup; Simonsen, Bo Cerup

    1999-01-01

    conventional ships. To reach a documented level of safety, it is therefore not possible directly to transfer experience with conventional ships. The purpose of this paper is to present new rational scientific tools to assess and quantify the collision risk associated with HSC transportation. The paper...... analysis tools to quantify the effect of the high speed have been available. Instead nearly all research on ship accidents has been devoted to analysis of the consequences of given accident scenarios. The proposed collision analysis includes an analysis which determines the probability of a collision...... for a HSC on a given route, an analysis of the released energy during a collision, analytical closed form solutions for the absorbed energy in the structure and finally an assessment of the overall structural crushing behaviour of the vessel, including the level of acceleration and the size of the crushing...

  11. Collision region of the ISR

    CERN Multimedia

    1970-01-01

    This is a collision region from the world’s first proton collider, the Intersecting Storage Rings. The ISR was used at CERN from 1971-84 to study proton-proton collisions at the highest energy then available (60GeV). When operational, ISR collision regions were surrounded by detectors as shown in the photo. In 1972, the surprising discovery of fragments flying out sideways from head-on proton-proton collisions was the first evidence of quark-quark scattering inside the colliding protons . This was similar to Rutherford’s observation in 1911 of alpha particles scattering off the tiny nucleus inside atoms of gold. The ISR beamtubes had to be as empty as outer space, a vacuum 100 000 times better than other CERN machines at the time.

  12. collision zone of an ISR

    CERN Multimedia

    This is a collision region from the world’s first proton collider, the Intersecting Storage Rings. The ISR was used at CERN from 1971-84 to study proton-proton collisions at the highest energy then available (60GeV). When operational, ISR collision regions were surrounded by detectors as shown in the photo. In 1972, the surprising discovery of fragments flying out sideways from head-on proton-proton collisions was the first evidence of quark-quark scattering inside the colliding protons . This was similar to Rutherford’s observation in 1911 of alpha particles scattering off the tiny nucleus inside atoms of gold. The ISR beamtubes had to be as empty as outer space, a vacuum 100 000 times better than other CERN machines at the time.

  13. Radiations from atomic collision processes

    International Nuclear Information System (INIS)

    Bernyi, D.

    1994-01-01

    The physics of atomic collision phenomena in which only the Coulomb forces have a role is an actual field or the research of the present days. The impact energy range in these collisions is very broad,it extends from the eV or even lower region to the GeV region or higher,i.e. it spans the region of three branches of physics,namely that of the atomic,the nuclear and the particle physics.To describe and explain the collision processes themselves, different models (collision mechanisms) are used and they are surveyed in the presentation. Different electromagnetic radiations and particles are emitted from the collision processes.Their features are shown in details together with the most important methods in their detection and study.Examples are given based on the literature and on the investigations of the author and his coworkers. The applications of the radiation from atomic collisions in other scientific fields and in the solution of different practical problems are also surveyed shortly. 16 figs., 2 tabs., 76 refs. (author)

  14. Frontal Sinus Breach During Routine Frontal Craniotomy Significantly Increases Risk of Surgical Site Infection: 10-Year Retrospective Analysis.

    Science.gov (United States)

    Linzey, Joseph R; Wilson, Thomas J; Sullivan, Stephen E; Thompson, B Gregory; Pandey, Aditya S

    2017-09-01

    Frontotemporal craniotomies are commonly performed for a variety of neurosurgical pathologies. Infections related to craniotomies cause significant morbidity. We hypothesized that the risk of cranial surgical site infections (SSIs) may be increased in patients whose frontal sinuses are breached during craniotomy. To compare the rate of cranial SSIs in patients undergoing frontotemporal craniotomies with and without frontal sinus breach (FSB). We performed a retrospective analysis of all patients undergoing frontotemporal craniotomies for the management of cerebral aneurysms from 2005 to 2014. This study included 862 patients undergoing 910 craniotomies. Primary outcome of interest was occurrence of a cranial SSI. Standard statistical methods were utilized to explore associations between a variety of variables including FSB, cranial SSI, and infections requiring reoperation. Of the 910 craniotomies, 141 (15.5%) involved FSB. Of those involving FSB, 22 (15.6%) developed a cranial SSI, compared to only 56 of the 769 without FSB (7.3%; P = .001). Cranial SSI requiring reoperation was much more likely in patients with FSB compared to those without a breach (7.8% vs 1.6%; P craniotomies are at significantly greater risk of serious cranial SSIs if the frontal sinus has been breached. Copyright © 2017 by the Congress of Neurological Surgeons

  15. Evaluation of the feasibility of joining titanium alloy to heavymet tungsten alloy

    International Nuclear Information System (INIS)

    1978-01-01

    Information is presented on a program to select and evaluate methods of brazing and/or explosively welding Ti-6Al-4V titanium alloy to Heavymet, a tungsten-base metal containing up to about 20% alloying elements (nickel, copper, etc.) to improve its ductility and other mechanical properties. Designs permitting the reliable production of joints between these base metals were of interest too. While this investigation was primarily concerned with an engineering study of the problems associated with joining these base metals in the required configuration, limited experimental studies were conducted also. The joining methods are reviewed individually. Recommendations for developing a viable titanium-tungsten joining procedure are discussed

  16. The mechanism of non-homologous end-joining: a synopsis of synapsis.

    Science.gov (United States)

    Weterings, Eric; van Gent, Dik C

    2004-11-02

    Repair of DNA double-strand breaks (DSBs) by non-homologous end-joining (NHEJ) is required for resistance to genotoxic agents, such as ionizing radiation, but also for proper development of the vertebrate immune system. Much progress has been made in identifying the factors that are involved in this repair pathway. We are now entering the phase in which we begin to understand basic concepts of the reaction mechanism and regulation of non-homologous end-joining. This review concentrates on novel insights into damage recognition and subsequent tethering, processing and joining of DNA ends.

  17. Failure Behavior of Aluminum-Titanium Hybrid Seams within a Novel Aluminum-CFRP Joining Concept

    Science.gov (United States)

    Woizeschke, P.; Schumacher, J.

    Modern light weight designs include various materials to create specific local properties. Hence, joining of dissimilar materials is an important task, especially the combination of carbon fiber reinforced plastics and aluminum alloys is a favored choice. In this paper, investigations on a novel joining concept for these materials are shown carried out within the DFG research group "Schwarz-Silber" at the University of Bremen. A titanium transition structure consisting of a foil laminate is applied. On the aluminum side joining is realized by a simultaneous double-sided laser process. In the results the failure behavior of this joint is characterized.

  18. Europlanet - Joining the European Planetary Research Information Service

    Science.gov (United States)

    Capria, M. T.; Chanteur, G.; Schmidt, W.

    2009-04-01

    The "Europlanet Research Infrastructure - Europlanet RI", supported by the European Commission's Framework Program 7, aims at integrating major parts of the distributed European Planetary Research infrastructure with as diverse components as space exploration, ground-based observations, laboratory experiments and numerical model-ling teams. A central part of Europlanet RI is the "Integrated and Distributed Information Service" or Europlanet-IDIS which intends to provide easy Web-based access to information about scientists and teams working in related fields, observatories or laboratories with capabilities possibly beneficial to planetary research, modelling expertise useful for planetary science and observations from space-based, ground-based or laboratory measurements. As far as the type of data and their access methods allow, IDIS will provide Virtual Observatory (VO) like access to a variety of data from distributed sources and tools to compare and integrate this information to further data analysis and re-search. IDIS itself is providing a platform for information and data sharing and for data mining. It is structured as a network of thematic nodes each concentrating on a sub-set of research areas in planetary sciences. But the most important elements of IDIS and the whole Europlanet RI are the single scientists, institutes, laboratories, observatories and mission project teams. Without them the whole effort would remain an empty shell. How can an interested individual or team join this activity and what are the benefits to be expected from the related effort? The poster gives detailed answers to these questions. Here some highlights: 1. Locate from the Europlanet web pages (addresses see below) the thematic node best related to the own field of expertise. This might be more than one. 2. Define which services you want to offer to the community: just the contact address, field of competence, off-line access to data on request or even on-line searchable access

  19. Is the frontal radiograph alone sufficient to evaluate for pneumonia in children?

    International Nuclear Information System (INIS)

    Rigsby, Cynthia K.; Strife, Janet L.; Johnson, Neil D.; Atherton, Harry D.; Kotagal, Uma R.; Pommersheim, William

    2004-01-01

    In our cost- and radiation-conscious environment, the feasibility of performing only a frontal radiograph for the diagnosis of pneumonia in children needs to be reassessed. To determine the diagnostic efficacy of the frontal radiograph alone in comparison to the frontal and lateral combined radiographs for the radiographic diagnosis of pneumonia in children. Three radiologists retrospectively and independently reviewed the frontal radiographs alone and separately reviewed the frontal and lateral radiographs of 1,268 children referred from the emergency room for chest radiographs. A majority interpretation of at least two radiologists for the frontal views alone was compared with majority interpretation of the frontal and lateral combined views for the radiographic diagnosis of pneumonia. ''Pneumonia'' was defined as a focus of streaky or confluent lung opacity. For the radiographic diagnosis of pneumonia, the sensitivity and specificity of the frontal view alone were 85% and 98%, respectively. For the confluent lobar type of pneumonia, the sensitivity and specificity increased to 100%. When the frontal view alone yields a diagnosis of confluent lobar pneumonia, this is highly reliable. However, nonlobar types of infiltrates will be underdiagnosed in 15% of patients using the frontal view alone. The clinical impact of these radiographically underdiagnosed pneumonias needs to be assessed prior to implementing the practice of using only frontal radiographs for diagnosing pneumonia. (orig.)

  20. Simplified bionic solutions: a simple bio-inspired vehicle collision detection system.

    Science.gov (United States)

    Hartbauer, Manfred

    2017-02-15

    Modern cars are equipped with both active and passive sensor systems that can detect potential collisions. In contrast, locusts avoid collisions solely by responding to certain visual cues that are associated with object looming. In neurophysiological experiments, I investigated the possibility that the 'collision-detector neurons' of locusts respond to impending collisions in films recorded with dashboard cameras of fast driving cars. In a complementary modelling approach, I developed a simple algorithm to reproduce the neuronal response that was recorded during object approach. Instead of applying elaborate algorithms that factored in object recognition and optic flow discrimination, I tested the hypothesis that motion detection restricted to a 'danger zone', in which frontal collisions on the motorways are most likely, is sufficient to estimate the risk of a collision. Furthermore, I investigated whether local motion vectors, obtained from the differential excitation of simulated direction-selective networks, could be used to predict evasive steering maneuvers and prevent undesired responses to motion artifacts. The results of the study demonstrate that the risk of impending collisions in real traffic scenes is mirrored in the excitation of the collision-detecting neuron (DCMD) of locusts. The modelling approach was able to reproduce this neuronal response even when the vehicle was driving at high speeds and image resolution was low (about 200  ×  100 pixels). Furthermore, evasive maneuvers that involved changing the steering direction and steering force could be planned by comparing the differences in the overall excitation levels of the simulated right and left direction-selective networks. Additionally, it was possible to suppress undesired responses of the algorithm to translatory movements, camera shake and ground shadows by evaluating local motion vectors. These estimated collision risk values and evasive steering vectors could be used as input

  1. Replacement collision sequences in metals

    International Nuclear Information System (INIS)

    Blewitt, T.H.; Kirk, M.A.; Scott, T.L.

    1975-10-01

    The concept of radiation-induced defects traveling large distances by focussed collision sequences (focusons) without thermal activation has important consequences in radiation effect studies. The focussed collision sequences are of two types: (1) ''Silsbee focussing'' or momentum focussing which can cause defect pairs to form large distances from the primary knock-on and (2) focussed replacement collisions also called ''dynamic crowdions'' where mass transport causes a large separation between the vacancy and its interstitial. Direct experimental evidence for focussed collision sequences is in short supply and conflicting. The sputtering patterns associated with close packed crystalline directions from the backscattering of charged particles seemed to substantiate long-range focussed collisions until it was pointed out that collision chains need not be long to yield such patterns. More recently, transmission sputtering has been used with conflicting results. Ecker et al. found no evidence for focusons greater than 17 atom distances whereas preliminary results of Siedman et al. suggest several hundred atom distances. Keil and co-workers found evidence for replacement collision sequences of 100 atom distances by stereo electron microscopy of interstitial agglomerates interjected by low energy heavy ion bombardment. Experiments by Kirk et al. and Becker and co-workers on ordered alloys, are only sensitive to dynamic crowdions. Kirk and co-workers result on the changes in magnetic properties of Ni 3 Mn induced by thermal neutron bombardment strongly support long range focusons (greater than 30 atom distances) whereas Wollenberger found no evidence for focusons with 1 and 3 MeV electron irradiation. Theoretical treatments of Liebfried suggest a maximum length of 30 atom distances whereas Holmes' modified treatment suggests less than 10 atom distances. (10 fig, 23 references)

  2. Intracranial EEG in predicting surgical outcome in frontal lobe epilepsy.

    Science.gov (United States)

    Holtkamp, Martin; Sharan, Ashwini; Sperling, Michael R

    2012-10-01

    Surgery in frontal lobe epilepsy (FLE) has a worse prognosis regarding seizure freedom than anterior lobectomy in temporal lobe epilepsy. The current study aimed to assess whether intracranial interictal and ictal EEG findings in addition to clinical and scalp EEG data help to predict outcome in a series of patients who needed invasive recording for FLE surgery. Patients with FLE who had resective surgery after chronic intracranial EEG recording were included. Outcome predictors were compared in patients with seizure freedom (group 1) and those with recurrent seizures (group 2) at 19-24 months after surgery. Twenty-five patients (16 female) were included in this study. Mean age of patients at epilepsy surgery was 32.3 ± 15.6 years (range 12-70); mean duration of epilepsy was 16.9 ± 13.4 years (range 1-48). In each outcome group, magnetic resonance imaging revealed frontal lobe lesions in three patients. Fifteen patients (60%) were seizure-free (Engel class 1), 10 patients (40%) continued to have seizures (two were class II, three were class III, and five were class IV). Lack of seizure freedom was seen more often in patients with epilepsy surgery on the left frontal lobe (group 1, 13%; group 2, 70%; p = 0.009) and on the dominant (27%; 70%; p = 0.049) hemisphere as well as in patients without aura (29%; 80%; p = 0.036), whereas sex, age at surgery, duration of epilepsy, and presence of an MRI lesion in the frontal lobe or extrafrontal structures were not different between groups. Electroencephalographic characteristics associated with lack of seizure freedom included presence of interictal epileptiform discharges in scalp recordings (31%; 90%; p = 0.01). Detailed analysis of intracranial EEG revealed widespread (>2 cm) (13%; 70%; p = 0.01) in contrast to focal seizure onset as well as shorter latency to onset of seizure spread (5.8 ± 6.1 s; 1.5 ± 2.3 s; p = 0.016) and to ictal involvement of brain structures beyond the frontal lobe (23.5 ± 22.4 s; 5.8 ± 5.4 s

  3. A Partial Join Approach for Mining Co-Location Patterns: A Summary of Results

    National Research Council Canada - National Science Library

    Yoo, Jin S; Shekhar, Shashi

    2005-01-01

    .... They propose a novel partial-join approach for mining co-location patterns efficiently. It transactionizes continuous spatial data while keeping track of the spatial information not modeled by transactions...

  4. Numerate Intends to Join ATOM Consortium to Rapidly Accelerate Preclinical Drug Development | FNLCR

    Science.gov (United States)

    SAN FRANCISCO – Computational drug design company Numerate has signed a letter of intent to join an open consortium of scientists staffed from two U.S. national laboratories, industry, and academia working to transform drug discovery and developmen

  5. Finite Element Simulation of Plastic Joining Processes of Steel and Aluminum Alloy Sheets

    Science.gov (United States)

    Mori, K.; Abe, Y.; Kato, T.

    2007-05-01

    Various high tensile strength steel sheets and an aluminum alloy sheet were joined with a self-piercing rivet. It is not easy to weld the aluminum alloy sheet and high tensile strength sheets by means of conventional resistance welding because of very different melting points. To obtain optimum joining conditions, joining defects were categorized into separation of the sheets and an inner fracture. The joining range of ultra high tensile strength steel and aluminum alloy sheets was extended by means of dies optimized by finite element simulation. The joint strength is greatly influenced by not only the strength of the sheets and rivets but also the ratio of the thickness of the lower sheet to the total thickness. In addition, mechanical clinching of high strength steel and aluminum alloy sheets was simulated.

  6. Summary of Dissimilar Metal Joining Trials Conducted by Edison Welding Institute

    International Nuclear Information System (INIS)

    MJ Lambert

    2005-01-01

    Under the direction of the NASA-Glenn Research Center, the Edison Welding Institute (EWI) in Columbus, OH performed a series of non-fusion joining experiments to determine the feasibility of joining refractory metals or refractory metal alloys to Ni-based superalloys. Results, as reported by EWI, can be found in the project report for EWI Project 48819GTH (Attachment A, at the end of this document), dated October 10, 2005. The three joining methods used in this investigation were inertia welding, magnetic pulse welding, and electro-spark deposition joining. Five materials were used in these experiments: Mo-47Re, T-111, Hastelloy X, Mar M-247 (coarse-grained, 0.5 mm to several millimeter average grain size), and Mar M-247 (fine-grained, approximately 50 (micro)m average grain size). Several iterative trials of each material combination with each joining method were performed to determine the best practice joining method. Mo-47Re was found to be joined easily to Hastelloy X via inertia welding, but inertia welding of the Mo-alloy to both Mar M-247 alloys resulted in inconsistent joint strength and large reaction layers between the two metals. T-111 was found to join well to Hastelloy X and coarse-grained Mar M-247 via inertia welding, but joining to fine-grained Mar M-247 resulted in low joint strength. Magnetic pulse welding (MPW) was only successful in joining T-111 tubing to Hastelloy X bar stock. The joint integrity and reaction layer between the metals were found to be acceptable. This single joining trial, however, caused damage to the electromagnetic concentrators used in this process. Subsequent design efforts to eliminate the problem resulted in a loss of power imparted to the accelerating work piece, and results could not be reproduced. Welding trials of Mar M-247 to T-111 resulted in catastrophic failure of the bar stock, even at lower power. Electro-spark deposition joining of Mo-47Re, in which the deposited material was Hastelloy X, did not have a

  7. Summary of Dissimilar Metal Joining Trials Conducted by Edison Welding Institute

    Energy Technology Data Exchange (ETDEWEB)

    MJ Lambert

    2005-11-18

    Under the direction of the NASA-Glenn Research Center, the Edison Welding Institute (EWI) in Columbus, OH performed a series of non-fusion joining experiments to determine the feasibility of joining refractory metals or refractory metal alloys to Ni-based superalloys. Results, as reported by EWI, can be found in the project report for EWI Project 48819GTH (Attachment A, at the end of this document), dated October 10, 2005. The three joining methods used in this investigation were inertia welding, magnetic pulse welding, and electro-spark deposition joining. Five materials were used in these experiments: Mo-47Re, T-111, Hastelloy X, Mar M-247 (coarse-grained, 0.5 mm to several millimeter average grain size), and Mar M-247 (fine-grained, approximately 50 {micro}m average grain size). Several iterative trials of each material combination with each joining method were performed to determine the best practice joining method. Mo-47Re was found to be joined easily to Hastelloy X via inertia welding, but inertia welding of the Mo-alloy to both Mar M-247 alloys resulted in inconsistent joint strength and large reaction layers between the two metals. T-111 was found to join well to Hastelloy X and coarse-grained Mar M-247 via inertia welding, but joining to fine-grained Mar M-247 resulted in low joint strength. Magnetic pulse welding (MPW) was only successful in joining T-111 tubing to Hastelloy X bar stock. The joint integrity and reaction layer between the metals were found to be acceptable. This single joining trial, however, caused damage to the electromagnetic concentrators used in this process. Subsequent design efforts to eliminate the problem resulted in a loss of power imparted to the accelerating work piece, and results could not be reproduced. Welding trials of Mar M-247 to T-111 resulted in catastrophic failure of the bar stock, even at lower power. Electro-spark deposition joining of Mo-47Re, in which the deposited material was Hastelloy X, did not have a

  8. Development of reconstitution method for surveillance specimens using surface activated joining

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Terumi; Kaihara, Shoichiro; Yoshida, Kazuo; Sato, Akira [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Onizawa, Kunio; Nishiyama, Yutaka; Fukaya, Kiyoshi; Suzuki, Masahide

    1996-03-01

    Evaluation of embrittlement of reactor vessel steel due to irradiation requires surveillance tests. However, many surveillance specimens are necessary for nuclear plants life extension. Therefore, a specimen reconstitution technique has become important to provide the many specimens for continued surveillance. A surface activated joining (SAJ) method has been developed to join various materials together at low temperatures with little deformation, and is useful to bond irradiated specimens. To assess the validity of this method, Charpy impact tests were carried out, and the characteristics caused by heating during joining were measured. The test results showed the Charpy impact values were almost the same as base materials, and surface activated joining reduced heat affected zone to less than 2 mm. (author).

  9. Research of the Processing Method to Improve Joining Quality of Adjustable Cylindrical Adhesive Joints

    Directory of Open Access Journals (Sweden)

    A. V. Ignatov

    2017-01-01

    Full Text Available The BMSTU has solved a task of developing an original processing method to join cylindrical adhesive joints, which allows joining quality improvement. A key point of the method is that joining is vertically arranged and a forced air supply with a given amount of the airflow pressure and temperature is directed from the bottom end towards upper one. This method allows locking the adhesive composition in the gap and arrangement of conditions for curing an adhesive composition without its outflow. In this case it is possible to adjust mutual bracing of joining pieces to reach a specified joining accuracy till the cure of adhesive composition.To study a new method of joining, the BMSTU has built an experimental unit and carried out a set of experiments with an anaerobic adhesive composition Loctite 638 with varying the gap in the join within the range from 0.1 to 0.7 mm. In the course of experiments an empirical dependence of the critical shearing force on the gap value in the join has been derived, as well as the recommended conditions for air quality to hold the adhesive compositions depending on viscosity has been revealed. As a result of experimental research, it is found that for adhesive composition of low-viscosity from 20 to 1000 cSt, a range of air quality for holding the adhesive composition in the assembly gap is from 9.8 to 196 Pa; for adhesive composition of middle-viscosity from 1000 to 2000 cSt, the recommended conditions lie in the range from 197 to 735.5 Pa; for adhesive composition of high-viscosity from 2000 to 5000 cSt, the recommended assembly conditions are from 736 to 1471 Pa. The realized studies have shown that using a new joining method, the amount of used adhesive composition is by about 25% less, the labor hours of the joining process are two times decreased, and the joining strength obtained is increased on average by 10-15% as compared to the traditional assembly methods of the adhesive cylindrical joint. This method

  10. Cocaine mummies and the pre-frontal reality

    International Nuclear Information System (INIS)

    Lloyd, Mark Anthony

    2001-01-01

    Full text: The scientific community frames its world with facts - facts which have been subjected to tests and apparently proven themselves and are therefore proffered by scientists to mankind as things upon which it can rely to steer it safely through life. However, facts are a moveable feast. Time and fresh minds often prove scientific 'facts' wrong. The cocaine mummies seem to indicate that 2000 years ago the Ancient Egyptians had access to both tobacco and cocaine - something previously believed impossible. One part of the German and British scientific community has proven in laboratory tests that the mummies are telling the truth. The rest of the scientific community disputes that truth'. But if the laboratory tests are right, then humanity has to rewrite its entire history. Nuclear communicators have very little credibility with the general public because they represent scientists, who not only are often proven wrong by time but also cannot agree on the truth. At the same time, there are fundamental facts about the human condition that nuclear communicators ignore - to the detriment of their message. Fact: thinking is a learned skill, not an instinct. Fact: language is a learned skill, not an instinct. For humans to follow the positive nuclear argument they must both think and also understand language. But thinking is not the brain's first choice of operation. Fact: the pre-frontal lobe of the brain is the seat of mankind's primitive emotions, including the instinct of fear and the instinct for life. The pre-frontal lobe dominates the way man thinks and speaks. Therefore, nuclear communicators have to learn the skill of mapping their messages to the pre-frontal human reality. This presentation provides practical points for that learning and message mapping exercise. (author)

  11. Functional role of frontal alpha oscillations in creativity.

    Science.gov (United States)

    Lustenberger, Caroline; Boyle, Michael R; Foulser, A Alban; Mellin, Juliann M; Fröhlich, Flavio

    2015-06-01

    Creativity, the ability to produce innovative ideas, is a key higher-order cognitive function that is poorly understood. At the level of macroscopic cortical network dynamics, recent electroencephalography (EEG) data suggests that cortical oscillations in the alpha frequency band (8-12 Hz) are correlated with creative thinking. However, whether alpha oscillations play a functional role in creativity has remained unknown. Here we show that creativity is increased by enhancing alpha power using 10 Hz transcranial alternating current stimulation (10 Hz-tACS) of the frontal cortex. In a study of 20 healthy participants with a randomized, balanced cross-over design, we found a significant improvement of 7.4% in the Creativity Index measured by the Torrance Test of Creative Thinking (TTCT), a comprehensive and most frequently used assay of creative potential and strengths. In a second similar study with 20 subjects, 40 Hz-tACS was used instead of 10 Hz-tACS to rule out a general "electrical stimulation" effect. No significant change in the Creativity Index was found for such frontal 40 Hz stimulation. Our results suggest that alpha activity in frontal brain areas is selectively involved in creativity; this enhancement represents the first demonstration of specific neuronal dynamics that drive creativity and can be modulated by non-invasive brain stimulation. Our findings agree with the model that alpha recruitment increases with internal processing demands and is involved in inhibitory top-down control, which is an important requirement for creative ideation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Development of a frontal small overlap crashworthiness evaluation test.

    Science.gov (United States)

    Sherwood, Christopher P; Mueller, Becky C; Nolan, Joseph M; Zuby, David S; Lund, Adrian K

    2013-01-01

    Small overlap frontal crashes are those in which crash forces are applied outboard of the vehicle's longitudinal frame rails. In-depth analyses of crashes indicate that such crashes account for a significant proportion of frontal crashes with seriously injured occupants. The objective of this research was to evaluate possible barrier crash tests that could be used to evaluate the crashworthiness of vehicles across a spectrum of small overlap crash types. Sixteen full-scale vehicle tests were conducted using 3 midsize passenger vehicles in up to 6 different test configurations, including vehicle-to-vehicle and barrier tests. All vehicles were tested at 64 km/h with an instrumented Hybrid III midsize male driver dummy. All test configurations resulted in primary loading of the wheel, suspension system, and hinge pillar. Vehicles underwent substantial lateral movement during the crash, which varied by crash configuration. The occupant compartments had significant intrusion, particularly to the most outboard structures. Inboard movement of the steering wheel in combination with outboard movement of the dummies (due to the lateral vehicle motion) caused limited interaction with the frontal air bag in most cases. When assessing overall crashworthiness (based on injury measures, structural deformation, and occupant kinematics), one vehicle had superior performance in each crash configuration. This was confirmation that the countermeasures benefiting performance in a single small overlap test also will provide a benefit in other crash configurations. Based on these test results, the Insurance Institute for Highway Safety has developed a small overlap crashworthiness evaluation with the following characteristics: a rigid flat barrier with a 150-mm corner radius, 25 percent overlap, 64 km/h test speed, and a Hybrid III midsize male driver dummy.

  13. Human Frontal-Subcortical Circuit and Asymmetric Belief Updating.

    Science.gov (United States)

    Moutsiana, Christina; Charpentier, Caroline J; Garrett, Neil; Cohen, Michael X; Sharot, Tali

    2015-10-21

    How humans integrate information to form beliefs about reality is a question that has engaged scientists for centuries, yet the biological system supporting this process is not well understood. One of the most salient attributes of information is valence. Whether a piece of news is good or bad is critical in determining whether it will alter our beliefs. Here, we reveal a frontal-subcortical circuit in the left hemisphere that is simultaneously associated with enhanced integration of favorable information into beliefs and impaired integration of unfavorable information. Specifically, for favorable information, stronger white matter connectivity within this system, particularly between the left inferior frontal gyrus (IFG) and left subcortical regions (including the amygdala, hippocampus, thalamus, putamen, and pallidum), as well as insular cortex, is associated with greater change in belief. However, for unfavorable information, stronger connectivity within this system, particularly between the left IFG and left pallidum, putamen, and insular cortex, is associated with reduced change in beliefs. These novel results are consistent with models suggesting that partially separable processes govern learning from favorable and unfavorable information. Beliefs of what may happen in the future are important, because they guide decisions and actions. Here, we illuminate how structural brain connectivity is related to the generation of subjective beliefs. We focus on how the valence of information is related to people's tendency to alter their beliefs. By quantifying the extent to which participants update their beliefs in response to desirable and undesirable information and relating those measures to the strength of white matter connectivity using diffusion tensor imaging, we characterize a left frontal-subcortical system that is associated simultaneously with greater belief updating in response to favorable information and reduced belief updating in response to

  14. Troubled Journeys: Some Motivations of Young Muslim Men to Join the Islamic State.

    Science.gov (United States)

    Yordanova, Kalina

    2016-09-01

    Large numbers of young people have joined jihadists groups in the Syrian/Iraqi conflict. Why would these young people decide to become jihadist fighters? What are the representations of the West they hold and how do these representations shape their decision? Drawing on the psychotherapeutic work with Syrian and Iraqi asylum seekers, this paper seeks to explain the most intimate reasons of young Muslim would-be fighters to join the Islamic State militias.

  15. A process and device for joining jacket leg chords in an off-shore platform

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, P.A.; Naudin, J.C.

    1995-04-07

    A joining process is presented that allows for the progressive junction, inside the chord, of the weld beads linking the joining parts with the other components of the chord, in order to prevent formation of stress concentration zones that are inconsistent with the high fatigue stresses that undergo off-shore platform jacket legs. The invention concerns also the device for the implementation of the process. 7 figs.

  16. Study of international published experiences in joining copper and copper-alloys

    International Nuclear Information System (INIS)

    Dahlgren, Aa.

    1997-04-01

    This study has revealed a number of joining processes to be used when manufacturing copper-canisters for the final storage of high level nuclear waste. However, the decision on which material and which joining process to be used has to be based on the design criterions. The welding procedure has to be qualified, i.e. it shall be demonstrated whether the procedure is capable of fulfilling specified requirements. 32 refs

  17. A technique for temporarily joining heavy construction parts, and tensioning element for such joining; Fremgangsmaate for midlertidig sammenfoeyning av tunge konstruksjonsdeler, samt spennelement for slik sammenfoeyning

    Energy Technology Data Exchange (ETDEWEB)

    Dunseth, S.; Gudmestad, O.T.; Stead, B.L.

    1996-04-15

    It is often required to temporarily join large construction parts. Traditionally this is done by means of seam welds that can be removed once the joint is no longer needed. For very large and heavy constructions, however, the strains may be so large that traditional welding methods do not meet the requirements. The problem can be solved by means of the present invention, which was developed for joining large underwater components in the offshore industry. The parts to be joined have at least one channel prepared to contain a tensioning cable. The contact surfaces of the parts are prepared for joining and sealing and the tensioning cable is fixed to anchor points at the end of a channel in the construction parts. At least one sealing pipe is thread into the channel with good clearance. At least one tensioning cable is thread through each pipe and fixed to the anchor points at the respective ends. The tensioning cables are grouted in the pipes, which remain loose within the channel. The invention also covers the tensioning system. 3 figs.

  18. Frontal sinus mucocele: a rare complication of craniofacial fibrous dysplasia.

    Science.gov (United States)

    Atasoy, C; Ustüner, E; Erden, I; Akyar, S

    2001-01-01

    We present plain radiographic, computed tomographic and magnetic resonance imaging (MRI) findings in a 25-year-old female patient with craniofacial fibrous dysplasia (FD). Although FD has a tendency to involve craniofacial bones in a unilateral fashion, the involvement was bilateral and extensive in this case. An additional feature was the presence of a frontal sinus mucocele, presumably due to the involvement of the sinus recess by the dysplastic process. This complication of the craniofacial FD has been reported very infrequently in the literature.

  19. Fibrous dysplasia of inferior turbinate, middle turbinate, and frontal sinus.

    Science.gov (United States)

    Ozcan, K M; Akdogan, O; Gedikli, Y; Ozcan, I; Dere, H; Unal, T

    2007-01-01

    Fibrous dysplasia (FD) is a non-neoplastic fibro-osseous lesion. Paranasal sinus involvement is infrequent. Involvement of the frontal sinus, sphenoid sinus, and middle turbinate is rare, and only sporadic cases have been reported in the literature. Nasal turbinates and especially the inferior turbinate are the least involved bones of the craniofacial region. To the best of our knowledge, only one case with McCune-Albright syndrome had FD of the inferior turbinate. Here, we report a rare case with FD of inferior and middle turbinates and review literature concerning FD of the craniofacial region.

  20. Evidence of mirror neurons in human inferior frontal gyrus.

    Science.gov (United States)

    Kilner, James M; Neal, Alice; Weiskopf, Nikolaus; Friston, Karl J; Frith, Chris D

    2009-08-12

    There is much current debate about the existence of mirror neurons in humans. To identify mirror neurons in the inferior frontal gyrus (IFG) of humans, we used a repetition suppression paradigm while measuring neural activity with functional magnetic resonance imaging. Subjects either executed or observed a series of actions. Here we show that in the IFG, responses were suppressed both when an executed action was followed by the same rather than a different observed action and when an observed action was followed by the same rather than a different executed action. This pattern of responses is consistent with that predicted by mirror neurons and is evidence of mirror neurons in the human IFG.

  1. A model of frontal polymerization using complex initiation

    Directory of Open Access Journals (Sweden)

    P. M. Goldfeder

    1999-01-01

    Full Text Available Frontal polymerization is a process in which a spatially localized reaction zone propagates into a monomer, converting it into a polymer. In the simplest case of free-radical polymerization, a mixture of monomer and initiator is placed in a test tube. A reaction is then initiated at one end of the tube. Over time, a self-sustained thermal wave, in which chemical conversion occurs, is produced. This phenomenon is possible because of the highly exothermic nature of the polymerization reactions.

  2. Frontal lobe hypoperfusion in mild cognitive impairment patients

    International Nuclear Information System (INIS)

    Liao, S.Q.; Chung, C.P.; Liao, Y.C.; Wang, P.N.; Lee, Y.C.; Liu, H.C.; Liu, R.S.

    2004-01-01

    Objective: Mild cognitive impairement (MCI) refers to the clinical state of individuals who are memory impaired subjectively but are functioning well and do not meet the criteria of dementia. MCI subjects have a high risk of progressing to Alzheimer's disease (AD). It is important to detect the earliest evidence of AD for clinicians to recognize the high risk subjects and to implicate the therapy. The aim of this study was to assess the early change of regional cerebral blood flow (rCBF) in MCI with high risk of AD by SPECT. Methods: Subjects complained of memory impairment with normal cognitive function and intact daily activities were enrolled. Each patient underwent 99mTc-HMPAO SPECT at the time of initial evaluation. Patients were followed for one to five years. The diagnosis of AD was based on the criteria of the Alzheimer's Disease and Related Disorders Association. There were 8 patients (4 males, 4 females; age range, 64-80 yrs; mean, 73.5 yrs) progressing to AD within one year. Ten gender and age matched normal control subjects (NC) were also included. The SPECT images were analyzed by using SPM 99. The image data were transformed into a standard stereotactic space, using a 12-parameter linear and 2x2x2 nonlinear spatial normalization with the template image. Group comparisons of the SPECT images between the 8 rapid AD converters and 10 NCs were performed on a voxel-by-voxel basis using t test. The t statistics was transformed to a normal statistic yielding a Z score for every voxel. Results: In 8 rapid AD converters, rCBF in the right medial frontal gyms (Brodmann area 10; BA 10), anterior cingulated gyms (BA 32) and middle frontal gyms (BA 46) was significantly lower than in NCs (p<0.001). The neuropsychological performances of these 8 cases revealed decrement in short-term memory, mental manipulation and list-generation frequency. Conclusions: rCBF is decreased in right medial frontal, anterior cingulated and middle frontal gyms in MCI patients who

  3. Injury severity assessment for car occupants in frontal impacts, using disability scaling.

    Science.gov (United States)

    Norin, H; Krafft, M; Korner, J; Nygren, A; Tingvall, C

    1997-01-01

    Injury classification and assessment is one of the most important fields of injury prevention. At present, injury assessment focuses primarily on the risk of fatalities, in spite of the fact that most people who are injured survive the trauma. The net result of a fatality-based approach is that safety and vehicle engineers must make decisions with an incomplete, and sometimes misleading, picture of the traffic safety problem. By applying disability scaling reflecting long-term consequences to injury data, the most significant disabling injuries can be identified. The priorities change with the level of disability used in the scaling. In this study, the risk of permanent medical disability due to different injuries was derived and linked to abbreviated injury scale (AIS) values for 24,087 different injured body regions. This material is based on insurance data. To study how the importance of different bodily injuries changes with different severity assessments in a realistic real-world injury distribution, Swedish insurance industry disability scaling was applied to 3066 cases of belted Volvo drivers involved in frontal collisions. Crash severity was included in the study by using equivalent barrier speed (EBS). When lower levels of disability are included, injuries to the neck and the extremities become the most important, while brain and skull injuries become the most prominent at higher levels of disability. The results presented in this article should be regarded as a contribution to the development of a suitable disability scaling method. The results can also be utilized to further injury research and vehicle design aimed at reducing injuries which have the most important long-term disability consequences.

  4. 1Restoration of ATM expression in DNA-PKcs deficient cells inhibits signal end joining

    Science.gov (United States)

    Neal, Jessica A.; Xu, Yao; Abe, Masumi; Hendrickson, Eric; Meek, Katheryn

    2016-01-01

    Unlike most DNA-PKcs deficient mouse cell strains, we show here that targeted deletion of DNA-PKcs in two different human cell lines abrogates VDJ signal end joining in episomal assays. Although the mechanism is not well defined, DNA-PKcs deficiency results in spontaneous reduction of ATM expression in many cultured cell lines (including those studied here) and in DNA-PKcs deficient mice. We considered that varying loss of ATM expression might explain differences in signal end joining in different cell strains and animal models, and we investigated the impact of ATM and/or DNA-PKcs loss on VDJ recombination in cultured human and rodent cell strains. To our surprise, in DNA-PKcs deficient mouse cell strains that are proficient in signal end joining, restoration of ATM expression markedly inhibits signal end joining. In contrast, in DNA-PKcs deficient cells that are deficient in signal end joining, complete loss of ATM enhances signal (but not coding) joint formation. We propose that ATM facilitates restriction of signal ends to the “classical” non-homologous end-joining pathway. PMID:26921311

  5. Joining of Silver Nanomaterials at Low Temperatures: Processes, Properties, and Applications.

    Science.gov (United States)

    Peng, Peng; Hu, Anming; Gerlich, Adrian P; Zou, Guisheng; Liu, Lei; Zhou, Y Norman

    2015-06-17

    A review is provided, which first considers low-temperature diffusion bonding with silver nanomaterials as filler materials via thermal sintering for microelectronic applications, and then other recent innovations in low-temperature joining are discussed. The theoretical background and transition of applications from micro to nanoparticle (NP) pastes based on joining using silver filler materials and nanojoining mechanisms are elucidated. The mechanical and electrical properties of sintered silver nanomaterial joints at low temperatures are discussed in terms of the key influencing factors, such as porosity and coverage of substrates, parameters for the sintering processes, and the size and shape of nanomaterials. Further, the use of sintered silver nanomaterials for printable electronics and as robust surface-enhanced Raman spectroscopy substrates by exploiting their optical properties is also considered. Other low-temperature nanojoining strategies such as optical welding of silver nanowires (NWs) through a plasmonic heating effect by visible light irradiation, ultrafast laser nanojoining, and ion-activated joining of silver NPs using ionic solvents are also summarized. In addition, pressure-driven joining of silver NWs with large plastic deformation and self-joining of gold or silver NWs via oriented attachment of clean and activated surfaces are summarized. Finally, at the end of this review, the future outlook for joining applications with silver nanomaterials is explored.

  6. Two different trichoscopic patterns of mid-frontal scalp in patients with frontal fibrosing alopecia and clinical features of androgenetic alopecia

    Directory of Open Access Journals (Sweden)

    Adriana Rakowska

    2017-03-01

    Full Text Available Introduction . Frontal fibrosing alopecia is a primary lymphocytic cicatricial alopecia with progressive frontotemporal hairline recession. In some cases, hair loss in the mid-frontal scalp, similar to female pattern hair loss, may be observed. Objective. Assessment of the trichoscopic pattern of mid-frontal scalp hair loss in patients diagnosed with frontal fibrosing alopecia. Material and methods. The retrospective analysis included 31 women diagnosed with frontal fibrosing alopecia and hair loss in the mid-frontal scalp and 36 women diagnosed with female pattern hair loss. Results . In patients with frontal fibrosing alopecia two different trichoscopic patterns in the mid-frontal scalp were identified. In 68% of patients (21/31 we observed a diffuse fibrotic pattern. It was characterized by irregular arrangement of follicular units with small areas with loss of follicular units, an increased percentage of follicular units with one hair and a decreased percentage of follicular units with three hairs, normal hair shaft thickness and presence of mild perifollicular scaling. The androgenetic alopecia pattern was present in 32% of patients (10/31. It was characterized by hair shaft thickness diversity (20% or more, a percentage of vellus hairs higher than 10%, presence of yellow dots, an increased percentage of follicular units with one hair and a decreased percentage of follicular units with three hairs. Conclusions. In patients with frontal fibrosing alopecia and coexisting mid-frontal scalp hair loss, we identified two different patterns of this area in trichoscopy: the diffuse fibrotic pattern (more common and the androgenetic alopecia pattern. This observation may have therapeutic and prognostic implications.

  7. Diffusion tensor imaging (DTI) in dementia patients with frontal lobe symptoms

    Energy Technology Data Exchange (ETDEWEB)

    Naik, Mala; Geitung, Jonn-Terje (Dept. of Geriatrics, Haraldsplass Deaconess Hospital, Bergen (Norway)), e-mail: mnaik@broadpark.no; Lundervold, Arvid (Dept. of Biomedicine, Univ. of Bergen (Norway)); Nygaard, Harald (Olaviken Hospital (Norway))

    2010-07-15

    Background: Diffusion tensor imaging (DTI) is a recent MRI technique demonstrating white matter tracts in the brain. Dementia is a neurodegenerative disease and this method has been used to demonstrate the loss of axonal fibers and myelin and decrease of fiber density in this condition. Purpose: To study a possible correlation between frontal lobe symptoms in patients with dementia and reduced fractional anisotropy (FA) in white matter/fascicles in the frontal lobes. Material and Methods: The study included 23 patients with dementia and frontal lobe symptoms and 20 controls (10 Alzheimer patients without frontal lobe symptoms and 10 normal controls). Clinical tests and MRI with DTI were performed. FA in subcortical white matter of both the frontal lobes was analyzed and correlated with clinical frontal score tests. Results: We found a significant correlation between frontal score results and reduction in FA in the frontal lobes. The FA in the study group was significantly lower than the FA in the control group. Conclusion: The present study reveals that there is a probable correlation between the extent of frontal lobe symptoms and FA in fascicles/white matter tissue in the frontal lobes

  8. Significance of frontal cortical atrophy in Parkinson's disease: computed tomographic study

    International Nuclear Information System (INIS)

    Lee, Kyung Sang; Suh, Jung Ho; Chung, Tae Sub; Kim, Dong Ik

    1987-01-01

    Fifty-five patients with Parkinson's disease were evaluated clinically and with brain computed tomography (CT) in order to determine the incidence of frontal cortical and subcortical atrophy. Twenty cases of age-related healthy control group were also scanned. The CT criteria of frontal cortical atrophy that was used in this study were the maximum width of frontal hemispheric cortical sulci and width of anterior interhemispheric fissure between frontal lobes comparing with maximum width of hemispheric cortical sulci except frontal lobes. And the criteria of frontal subcortical atrophy were bifrontal index bicaudate index, and Evans index. The results are as follows: 1. Cortical atrophic changes in Parkinson's disease were more prominent in frontal lobe rather than other causes of cortical atrophy. 2. Frontal cortical and subcortical atrophic changes were also more prominent in Parkinson's disease rather than age-related control group. 3. Subcortical atrophic changes in frontal lobe were always associated with cortical atrophic changes. 4. Changes of basal ganglia were hardly seen in Parkinson's disease. 5. Cortical atrophic changes in frontal lobe must be the one of significant findings in Parkinson's disease

  9. Polarized Proton Collisions at RHIC

    CERN Document Server

    Bai, Mei; Alekseev, Igor G; Alessi, James; Beebe-Wang, Joanne; Blaskiewicz, Michael; Bravar, Alessandro; Brennan, Joseph M; Bruno, Donald; Bunce, Gerry; Butler, John J; Cameron, Peter; Connolly, Roger; De Long, Joseph; Drees, Angelika; Fischer, Wolfram; Ganetis, George; Gardner, Chris J; Glenn, Joseph; Hayes, Thomas; Hseuh Hsiao Chaun; Huang, Haixin; Ingrassia, Peter; Iriso, Ubaldo; Laster, Jonathan S; Lee, Roger C; Luccio, Alfredo U; Luo, Yun; MacKay, William W; Makdisi, Yousef; Marr, Gregory J; Marusic, Al; McIntyre, Gary; Michnoff, Robert; Montag, Christoph; Morris, John; Nicoletti, Tony; Oddo, Peter; Oerter, Brian; Osamu, Jinnouchi; Pilat, Fulvia Caterina; Ptitsyn, Vadim; Roser, Thomas; Satogata, Todd; Smith, Kevin T; Svirida, Dima; Tepikian, Steven; Tomas, Rogelio; Trbojevic, Dejan; Tsoupas, Nicholaos; Tuozzolo, Joseph; Vetter, Kurt; Wilinski, Michelle; Zaltsman, Alex; Zelenski, Anatoli; Zeno, Keith; Zhang, S Y

    2005-01-01

    The Relativistic Heavy Ion Collider~(RHIC) provides not only collisions of ions but also collisions of polarized protons. In a circular accelerator, the polarization of polarized proton beam can be partially or fully lost when a spin depolarizing resonance is encountered. To preserve the beam polarization during acceleration, two full Siberian snakes were employed in RHIC to avoid depolarizing resonances. In 2003, polarized proton beams were accelerated to 100~GeV and collided in RHIC. Beams were brought into collisions with longitudinal polarization at the experiments STAR and PHENIX by using spin rotators. RHIC polarized proton run experience demonstrates that optimizing polarization transmission efficiency and improving luminosity performance are significant challenges. Currently, the luminosity lifetime in RHIC is limited by the beam-beam effect. The current state of RHIC polarized proton program, including its dedicated physics run in 2005 and efforts to optimize luminosity production in beam-beam limite...

  10. Nucleus behavior in violent collisions

    International Nuclear Information System (INIS)

    Lefort, M.; Galin, J.; Guerreau, D.

    1985-01-01

    Thanks to new heavy ion beams (Argon, Krypton...) accelerated at Ganil and Sara to velocities of about 0.2 to 0.5 times the light one, very violent collisions, between complex nuclei can be made. During peripheral collisions, the projectile is strongly heated in '' wearing away'' the target and follows its way at high velocity in loosing nucleons. Resulting fragments can present themselves as nuclei very different from usual stable nuclei, often at existence limit. In more central collisions, the energy transferred is such that fusion of both leads to a new type of very hot nucleus near the immediate boiling. Another existence limit is reached by this way: where the bound nucleon system tend to become nucleon gas or a bulk of little fragments [fr

  11. Semiholography for heavy ion collisions

    CERN Document Server

    Mukhopadhyay, Ayan

    2017-01-01

    The formation of QGP in heavy ion collisions gives us a great opportunity for learning about nonperturbative dynamics of QCD. Semiholography provides a new consistent framework to combine perturbative and non-perturbative effects in a coherent way and can be applied to obtain an effective description for heavy ion collisions. In particular, it allows us to include nonperturbative effects in existing glasma effective theory and QCD kinetic theory for the weakly coupled saturated degrees of freedom liberated by the collisions in the initial stages in a consistent manner. We argue why the full framework should be able to confront experiments with only a few phenomenological parameters and present feasibility tests for the necessary numerical computations. Furthermore, we discuss that semiholography leads to a new description of collective flow in the form of a generalised non-Newtonian fluid. We discuss some open questions which we hope to answer in the near future.

  12. QCD in heavy ion collisions

    CERN Document Server

    Iancu, Edmond

    2014-04-10

    These lectures provide a modern introduction to selected topics in the physics of ultrarelativistic heavy ion collisions which shed light on the fundamental theory of strong interactions, the Quantum Chromodynamics. The emphasis is on the partonic forms of QCD matter which exist in the early and intermediate stages of a collision -- the colour glass condensate, the glasma, and the quark-gluon plasma -- and on the effective theories that are used for their description. These theories provide qualitative and even quantitative insight into a wealth of remarkable phenomena observed in nucleus-nucleus or deuteron-nucleus collisions at RHIC and/or the LHC, like the suppression of particle production and of azimuthal correlations at forward rapidities, the energy and centrality dependence of the multiplicities, the ridge effect, the limiting fragmentation, the jet quenching, or the dijet asymmetry.

  13. Cold molecules, collisions and reactions

    Science.gov (United States)

    Hecker Denschlag, Johannes

    2016-05-01

    I will report on recent experiments of my group where we have been studying the formation of ultracold diatomic molecules and their subsequent inelastic/reactive collisions. For example, in one of these experiments we investigate collisions of triplet Rb2 molecules in the rovibrational ground state. We observe fast molecular loss and compare the measured loss rates to predictions based on universality. In another set of experiments we investigate the formation of (BaRb)+ molecules after three-body recombination of a single Ba+ ion with two Rb atoms in an ultracold gas of Rb atoms. Our investigations indicate that the formed (BaRb)+ molecules are weakly bound and that several secondary processes take place ranging from photodissociation of the (BaRb)+ molecule to reactive collisions with Rb atoms. I will explain how we can experimentally distinguish these processes and what the typical reaction rates are. Support from the German Research foundation DFG and the European Community is acknowledged.

  14. Frontal lobe function and behavioral changes in amyotrophic lateral sclerosis: a study from Southwest China.

    Science.gov (United States)

    Wei, QianQian; Chen, XuePing; Zheng, ZhenZhen; Huang, Rui; Guo, XiaoYan; Cao, Bei; Zhao, Bi; Shang, Hui-Fang

    2014-12-01

    Despite growing interest, the frequency and characteristics of frontal lobe functional and behavioral deficits in Chinese people with amyotrophic lateral sclerosis (ALS), as well as their impact on the survival of ALS patients, remain unknown. The Chinese version of the frontal assessment battery (FAB) and frontal behavioral inventory (FBI) were used to evaluate 126 sporadic ALS patients and 50 healthy controls. The prevalence of frontal lobe dysfunction was 32.5%. The most notable impairment domain of the FAB was lexical fluency (30.7%). The binary logistic regression model revealed that an onset age older than 45 years (OR 5.976, P = 0.002) and a lower educational level (OR 0.858, P = 0.002) were potential determinants of an abnormal FAB. Based on the FBI score, 46.0% of patients showed varied degrees of frontal behavioral changes. The most common impaired neurobehavioral domains were irritability (25.4%), logopenia (20.6%) and apathy (19.0%). The binary logistic regression model revealed that the ALS Functional Rating Scale-Revised scale score (OR 0.127, P = 0.001) was a potential determinant of an abnormal FBI. Frontal functional impairment and the severity of frontal behavioral changes were not associated with the survival status or the progression of ALS by the cox proportional hazard model and multivariate regression analyses, respectively. Frontal lobe dysfunction and frontal behavioral changes are common in Chinese ALS patients. Frontal lobe dysfunction may be related to the onset age and educational level. The severity of frontal behavioral changes may be associated with the ALSFRS-R. However, the frontal functional impairment and the frontal behavioral changes do not worsen the progression or survival of ALS.

  15. Preoperative neuropsychological presentation of patients with refractory frontal lobe epilepsy.

    Science.gov (United States)

    Patrikelis, Panayiotis; Gatzonis, Stylianos; Siatouni, Anna; Angelopoulos, Elias; Konstantakopoulos, George; Takousi, Maria; Sakas, Damianos E; Zalonis, Ioannis

    2016-06-01

    This study investigated whether certain cognitive deficits are associated with frontal lobe epilepsy (FLE) aiming to contribute with localization data to the preoperative assessment of epilepsy surgery candidates. We evaluated 34 patients with refractory FLE, 37 patients with refractory medial temporal lobe epilepsy (MTLE), and 22 healthy individuals in attention, psychomotor speed, motor function, verbal memory span, verbal fluency, response inhibition/interference, concept formation and set shifting, anticipation and planning, global memory. Neuropsychological performances of FLE and MTLE were similar, with the only exception the WCST-number of categories index, measuring mental flexibility, in which MTLE patients performed significantly worse than FLE patients. Left-FLE patients presented more perseverative responding compared to both other patient groups and healthy controls (HCs), while left-MTLE patients showed worse sorting abilities than the other epilepsy groups. Our findings suggest a weak cognitive differentiation between FLE and MTLE, probably attributed to the intricate nature of fronto-temporal connectivity frequently resulting in overlapping deficits as well as the confounding effects of seizure-related variables. In clinical practice, a highly individualized (idiographic) neuropsychological approach along with the inclusion of concurrent EEG recordings (e.g., interictal coupling) may be of help for neuropsychologists in identifying FLE patients from those with medial temporal pathology presenting frontal dysfunction as a secondary cognitive symptom.

  16. Frontal intradiploic epidomoid cyst with orbital and out cerebral extension

    International Nuclear Information System (INIS)

    Fernandez Latorre, F.; Revert Ventura, A.; Diaz Ramon, C.; Arana, E.; Esteban Masanet, J.M.; Tortosa Giner, A.

    1995-01-01

    We studied six patients with exophthalmos and inferior displacement of the eyeball produced by orbital extension of a frontal intradiploic epidermoid cyst. All the patients were studied by conventional radiography five with CT and three with MR. Plain x-ray disclosed a single, well-defined lytic lesion with sclerosis margin, located in the outer supraorbital region of the frontal bone in all cases. CT revealed the intradiploic site of the lesion, its expansive nature, the state of the bone tables and demonstrated the existence of an intra orbital mass. MR showed a lesion with a greater signal intensity than LCR, similar to the white matter in T1-weighted sequences in two cases and hyperintense in a third. The lesions were hyperintense in T2-weighted sequences. The preoperative presumed diagnosis was established by means of plain radiography on the basis of site and the sclerosis ring surrounding the lesion. CT disclosed the bone structures and confirmed the existence of an intra orbital mass containing soft portions. The basic contribution of MR was in the assessment of the intracranial extension and in ruling out cerebral involvement.(Author)

  17. Ventrolateral and dorsomedial frontal cortex lesions impair mnemonic context retrieval.

    Science.gov (United States)

    Chapados, Catherine; Petrides, Michael

    2015-02-22

    The prefrontal cortex appears to contribute to the mnemonic retrieval of the context within which stimuli are experienced, but only under certain conditions that remain to be clarified. Patients with lesions to the frontal cortex, the temporal lobe and neurologically intact individuals were tested for context memory retrieval when verbal stimuli (words) had been experienced across multiple (unstable context condition) or unique (stable context condition) contexts; basic recognition memory of these words-in-contexts was also tested. Patients with lesions to the right ventrolateral prefrontal cortex (VLPFC) were impaired on context retrieval only when the words had been seen in multiple contexts, demonstrating that this prefrontal region is critical for active retrieval processing necessary to disambiguate memory items embedded across multiple contexts. Patients with lesions to the left dorsomedial prefrontal region were impaired on both context retrieval conditions, regardless of the stability of the stimulus-to-context associations. Conversely, prefrontal lesions sparing the ventrolateral and dorsomedial regions did not impair context retrieval. Only patients with temporal lobe excisions were impaired on basic recognition memory. The results demonstrate a basic contribution of the left dorsomedial frontal region to mnemonic context retrieval, with the VLPFC engaged, selectively, when contextual relations are unstable and require disambiguation. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

  18. The underestimation of egocentric distance: evidence from frontal matching tasks

    Science.gov (United States)

    Li, Zhi; Phillips, John

    2011-01-01

    There is controversy over the existence, nature, and cause of error in egocentric distance judgments. One proposal is that the systematic biases often found in explicit judgments of egocentric distance along the ground may be related to recently observed biases in the perceived declination of gaze (Durgin & Li, Attention, Perception, & Psychophysics, in press), To measure perceived egocentric distance nonverbally, observers in a field were asked to position themselves so that their distance from one of two experimenters was equal to the frontal distance between the experimenters. Observers placed themselves too far away, consistent with egocentric distance underestimation. A similar experiment was conducted with vertical frontal extents. Both experiments were replicated in panoramic virtual reality. Perceived egocentric distance was quantitatively consistent with angular bias in perceived gaze declination (1.5 gain). Finally, an exocentric distance-matching task was contrasted with a variant of the egocentric matching task. The egocentric matching data approximate a constant compression of perceived egocentric distance with a power function exponent of nearly 1; exocentric matches had an exponent of about 0.67. The divergent pattern between egocentric and exocentric matches suggests that they depend on different visual cues. PMID:21735313

  19. Frontal Cortical Atrophy as a Predictor of Poststroke Apathy.

    Science.gov (United States)

    Mihalov, Ján; Mikula, Peter; Budiš, Jaroslav; Valkovič, Peter

    2016-07-01

    The aim of the study was to identify associations between the symptoms of poststroke apathy and sociodemographic, stroke-related (severity of stroke, degree of disability, and performance in activities of daily living), and radiological correlates. We determined the degree of cortical and subcortical brain atrophy, the severity of white matter and basal ganglia lesions on baseline computed tomography (CT) scans, and the localization of acute ischemia on control CT or magnetic resonance imaging scans in subacute stages of stroke. During follow-up examinations, in addition to the assessment of apathy symptoms using the Apathy Scale, we also evaluated symptoms of depression and anxiety using the Hospital Anxiety and Depression Scale. The study included 47 consecutive patients with acute ischemic stroke. Correlates significantly associated with apathy, determined at baseline and during follow-up, were entered into the "predictive" and "associative" multiple regression models, respectively. Frontal cortical atrophy and symptoms of depression were most strongly associated with poststroke apathy symptoms. In order to model an interrelation between both cortical atrophy and white matter lesions and aging, we supplemented 2 additional "predictive" models using interaction variables, whereby we confirmed the role of frontal cortical atrophy as a predictor of poststroke apathy also as a function of the increasing age of patients. © The Author(s) 2016.

  20. Development and validation of the Frontal Fibrosing Alopecia Severity Score.

    Science.gov (United States)

    Saceda-Corralo, David; Moreno-Arrones, Óscar Muñoz; Fonda-Pascual, Pablo; Pindado-Ortega, Cristina; Buendía-Castaño, Diego; Alegre-Sánchez, Adrián; Segurado-Miravalles, Gonzalo; Rodrigues-Barata, Ana Rita; Jaén-Olasolo, Pedro; Vaño-Galván, Sergio

    2018-03-01

    Frontal fibrosing alopecia (FFA) is a scarring alopecia characterized by recession of the frontotemporal hairline and loss of the eyebrows. To design and validate a scoring system to assess the severity of FFA. The Frontal Fibrosing Alopecia Severity Score (FFASS) was developed; criterion validity was assessed by the Investigator's Global Assessment, and construct validity was evaluated by the convergence of other measures of severity (the Patient's Global Assessment], the rest of the clinical features, the Lichen Planopilaris Activity Index, and quality of life measures (Dermatology Life Quality Index and Hospital Anxiety Depression Scale). Intraobserver and interobserver reliability were determined. In total, 103 female patients were included. The FFASS showed significant correlation to the Patient's Global Assessment, occipital involvement, and the Lichen Planopilaris Activity Index. Intraobserver reliability was completed for 31 subjects and showed good correlation (intraclass correlation coefficient, 0.86; 95% confidence interval, 0.7-0.95; P < .001). Interobserver reliability showed excellent correlation (intraclass correlation coefficient, 0.97; 95% confidence interval, 0.95-0.99; P < .001). The study was performed at a single institution, and only female patients were assessed. The FFASS is a statistically validated scale and a reliable measure of FFA severity, and it can be used in clinical practice and future research studies as an assessment tool. Copyright © 2017 American Academy of Dermatology, Inc. Published by Elsevier Inc. All rights reserved.

  1. Contemporary management of frontal sinus mucoceles: a meta-analysis.

    Science.gov (United States)

    Courson, Andy M; Stankiewicz, James A; Lal, Devyani

    2014-02-01

    To analyze trends in the surgical management of frontal and fronto-ethmoid mucoceles through meta-analysis. Meta-analysis and case series. A systematic literature review on surgical management of frontal and fronto-ethmoid mucoceles was conducted. Studies were divided into historical (1975-2001) and contemporary (2002-2012) groups. A meta-analysis of these studies was performed. The historical and contemporary cohorts were compared (surgical approach, recurrence, and complications). To study evolution in surgical management, a senior surgeon's experience over 28 years was analyzed separately. Thirty-one studies were included for meta-analysis. The historical cohort included 425 mucoceles from 11 studies. The contemporary cohort included 542 mucoceles from 20 studies. More endoscopic techniques were used in the contemporary versus historical cohort (53.9% vs. 24.7%; P = contemporary). In the historical cohort, higher recurrence was noted in the external group (P = 0.03). Results from endoscopic and open approaches are comparable. Although endoscopic techniques are being increasingly adopted, comparison with our series shows that more cases could potentially be treated endoscopically. Frequent use of open approaches may reflect efficacy, or perhaps lack of expertise and equipment required for endoscopic management. Most contemporary authors favor endoscopic management, limiting open approaches for specific indications (unfavorable anatomy, lateral disease, and scarring). N/A. Copyright © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

  2. Seizure semiology of lesional frontal lobe epilepsies in children.

    Science.gov (United States)

    Battaglia, D; Lettori, D; Contaldo, I; Veredice, C; Sacco, A; Vasco, J; Martinelli, D; Chieffo, D; Tartaglione, T; Colosimo, C; Di Rocco, C; Guzzetta, F

    2007-12-01

    The aim of the study was to analyse the semiology of seizures in children with frontal lobe epilepsy (FLE) and to compare them with other paediatric cohorts described in the literature as well as with adult counterparts. We analysed 174 registered seizures of 18 cases under 12 years with lesional epilepsy whose frontal origin was defined by the concordance of neuroimaging and ictal electrographic findings, and confirmed by surgery in the six cases operated on. Seizures were generally short, with a high daily frequency and usually related to sleep. The most characteristic semiological pattern consisted of complex motor seizures, particularly hypermotor. Often seizures corresponded to a mixture of different semiological patterns (tonic, gelastic, automotor, hypermotor, versive) presenting in the same seizure, often as a unique type in the same patient. With regard to several aspects the semiology of FLE in our cohort looks like that reported in adult series, in particular as to the frequency of complex motor seizures. However, our cohort was also characterised by a more protean array of seizure semiology, stressing the occurrence of seizures typically present in adults (versive and complex motor) and of some seizure patterns more characteristic in children such as epileptic spasms; moreover, the rare occurrence of secondarily generalised tonic clonic seizures (SGTCS) was confirmed.

  3. Comparative analysis of the practice of China and Russia joining the WTO

    Directory of Open Access Journals (Sweden)

    Anastasia Sergeyevna Loginova

    2015-09-01

    Full Text Available Objective to examine the positive and negative experience of China39s joining the World Trade Organization WTO that joined it on terms similar to the Russian ones for the best understanding of the advantages and disadvantages of joining and building the appropriate policy. Methods the objective of the work has been achieved through the application of both general and specific scientific methods. In particular the analysis and synthesis allowed to study the social and economic context of the state in the framework of joining the WTO the consequences of such membership and to identify the key areas for improvement of this step for Russia. Statistical techniques were used in the process of gathering information about the key economic indicators. The fundamental method was comparativelegal which made it possible to draw parallels in joining the WTO by various states. Results basing on the measures taken by China both before and after joining the WTO as well as evaluation of their implication the conclusion was made about its successful experience. The actions before joining were very effective. In particular they are applicable to the fields of agriculture automotive industry investment policy etc. The measures of nonaddress subsidizing maintaining the socioeconomic stability in the country the export orientation of the economy along with functioning of special economic zones with joint ventures are in the authors39 opinion constructive actions for Russiarsquos adaptation to the WTO. Scientific novelty for the first time the thesis is put forward about the similarity of the Russia and China conditions when joining the WTO. The analysis is made of the complex measures preceding and following the joining. The necessity is grounded of reflecting the China39s positive and negative experiences in the Russian policy. Practical significance the main provisions and conclusions can be used in the research activity in addressing the issues of Russiarsquos

  4. Outreach Materials for the Collision Repair Campaign

    Science.gov (United States)

    The Collision Repair Campaign offers outreach materials to help collision repair shops reduce toxic air exposure. Materials include a DVD, poster, training video, and materials in Spanish (materiales del outreach en español).

  5. Spectroscopic studies of hydrogen collisions

    International Nuclear Information System (INIS)

    Kielkopf, J.

    1991-01-01

    Low energy collisions involving neutral excited states of hydrogen are being studied with vacuum ultraviolet spectroscopy. Atomic hydrogen is generated by focusing an energetic pulse of ArF, KrF, or YAG laser light into a cell of molecular hydrogen, where a plasma is created near the focal point. The H 2 molecules in and near this region are dissociated, and the cooling atomic hydrogen gas is examined with laser and dispersive optical spectroscopy. In related experiments, we are also investigating neutral H + O and H + metal - atom collisions in these laser-generated plasmas

  6. High-energy ion-atom collisions

    International Nuclear Information System (INIS)

    Berenyi, Denes.

    1987-01-01

    The progress in energetic ion-atom collision studies is shown briefly on the basis of the Workshop in the field above held in Debrecen. The 'hot topics', namely 'two-center' and electron correlation phenomena, collisions with antiprotons, recent results on alignment and orientation in energetic heavy-ion collisions, autoionization electron studies in the meV region and the utilization of heavy-ion storage rings in ion-atom collision experiments are treated. (author) 4 figs

  7. Distraction-related road traffic collisions

    African Journals Online (AJOL)

    Abstract. Objectives: We aimed to prospectively study distraction-related road traffic collision injuries, their contributory factors, severity, and outcome. Methods: Data were prospectively collected on all hospitalized road traffic collision trauma patients in Al-Ain City who were drivers at the collision time over one and half years ...

  8. Photoinitiated collisions between cold Cs Rydberg atoms

    International Nuclear Information System (INIS)

    Overstreet, K. Richard; Schwettmann, Arne; Tallant, Jonathan; Shaffer, James P.

    2007-01-01

    Experimental studies of a photoinitiated collision in an ultracold Cs Rydberg gas are presented. The process is characterized by measuring the laser intensity dependence of the absorption, the number of particles leaving each collision, and the recoil velocity of the collision fragments. The results of the experiment are compared to ab initio Rydberg pair interaction potentials

  9. NA49: lead-lead collision

    CERN Multimedia

    1996-01-01

    This is an image of an actual lead ion collision taken from tracking detectors on the NA49 experiment, part of the heavy ion project at CERN. These collisions produce a very complicated array of hadrons as the heavy ions break up. It is hoped that one of these collisions will eventually create a new state of matter known as quark-gluon plasma.

  10. Auditory aura in nocturnal frontal lobe epilepsy: a red flag to suspect an extra-frontal epileptogenic zone.

    Science.gov (United States)

    Ferri, Lorenzo; Bisulli, Francesca; Nobili, Lino; Tassi, Laura; Licchetta, Laura; Mostacci, Barbara; Stipa, Carlotta; Mainieri, Greta; Bernabè, Giorgia; Provini, Federica; Tinuper, Paolo

    2014-11-01

    To describe the anatomo-electro-clinical findings of patients with nocturnal hypermotor seizures (NHS) preceded by auditory symptoms, to evaluate the localizing value of auditory aura. Our database of 165 patients with nocturnal frontal lobe epilepsy (NFLE) diagnosis confirmed by videopolysomnography (VPSG) was reviewed, selecting those who reported an auditory aura as the initial ictal symptom in at least two NHS during their lifetime. Eleven patients were selected (seven males, four females). According to the anatomo-electro-clinical data, three groups were identified. Group 1 [defined epileptogenic zone (EZ)]: three subjects were studied with stereo-EEG. The EZ lay in the left superior temporal gyrus in two cases, whereas in the third case seizures arose from a dysplastic lesion located in the left temporal lobe. One of these three patients underwent left Heschl's gyrus resection, and is currently seizure-free. Group 2 (presumed EZ): three cases in which a presumed EZ was identified; in the left temporal lobe in two cases and in the left temporal lobe extending to the insula in one subject. Group 3 (uncertain EZ): five cases had anatomo-electro-clinical correlations discordant. This work suggests that auditory aura may be a helpful anamnestic feature suggesting an extra-frontal seizure origin. This finding could guide secondary investigations to improve diagnostic definition and selection of candidates for surgical treatment. Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

  11. Contemporary Presence of Dynamical and Statistical Intermediate Mass Fragment Production Mechanisms in Midperipheral NI+NI Collisions at 30 MeV/nucleon

    Science.gov (United States)

    Milazzo, P. M.; Sisto, M.; Margagliotti, G. V.; Rui, R.; Vannini, G.; Bruno, M.; D'Agostino, M.; Colonna, N.; Agodi, C.; Alba, R.; Bellia, G.; Colonna, M.; Coniglione, R.; Del Zoppo, A.; Finocchiaro, P.; Maiolino, C.; Migneco, E.; Piattelli, P.; Santonocito, D.; Sapienza, P.; Gramegna, F.; Mastinu, P. F.; Fabbietti, L.; Iori, I.; Moroni, A.; Belkacem, M.

    2001-11-01

    The 58Ni+58Ni reaction at 30 MeV/nucleon has been experimentally investigated at the Superconducting Cyclotron of the INFN Laboratori Nazionali del Sud. In midperipheral collisions the production of massive fragments (4 ≤ Z ≤ 12), consistent with the statistical fragmentation of the projectile-like residue and the contemporary dynamical fragmentation of a neck, joining projectile-like and target-like residues, has been observed.

  12. Sforzellina Glaciers: Glacial Geomorfology, Mass Balance, Frontal Variations and Dendroglaciology

    Science.gov (United States)

    Diolaiuti, G.; D'Agata, C.; Smiraglia, C.; Santilli, M. Pelfini M.

    The Sforzellina Glacier is a small cirque glacier located in Gavia Valley, in the Lom- bardy side of the Ortles-Cevedale Group (Italy). Although its modest dimensions, it is an important source of glaciological and geomorphological data; it is in fact moni- torated over a long time, more than seventy years, by the Italian Glaciological Com- mitteeSs (CGI) relatively to the frontal variations and so now is available a complete data set that was used in order to calculate the correlation with other alpine italian glaciers. The analysis allowed to estimate that this small cirque glacier is in phase with a large number of alpine glacial bodies. The glacier had a continuous and un- interrupted retreating phase from 1925 to the beginning of the 70s of XXth century when a frontal progress phase started. This new trend culminated in 1985 and finished in 1987. From that year the glacier resumed a continuous and uninterrupted frontal retreat. From 1925 to 2000 the glacier retreated was of 379 m. From 1987 up to now Sforzellina is used as a sample glacier for mass balance measurements and all the data (15 years of mass balance data) were correlated with the other Italian and European mass balance data; this analysis allowed to notice that this glacier was strongly corre- lated with many of the monitorated alpine glaciers located in the same climatic region. This result suggests to continue the monitoring of Sforzellina as important climatic and environmental index and suggests to use the data in order to calcolate matemathi- cal models to create alpine glacier scenaries. From 1987 to 2000 the Sforzellina mass balances were constantly negative. In the hydrological year 2000-2001 there was a change in mass balance trend with a moderately positive mass balance. In 15 years the glacier lost a thickness of about 13 m w.e. In the summers 1999 and 2000 the glacier was studied by means of sysmic and radar geophysical surveys to determinate the thickness, that was resulted of about 40

  13. Recurrent meningitis associated with frontal sinus tuber encephalocele in a patient with tuberous sclerosis.

    Science.gov (United States)

    Elbabaa, Samer K; Riggs, Angela D; Saad, Ali G

    2011-07-01

    Tuberous sclerosis complex (TSC) is a genetic neurocutaneous disorder that commonly affects the CNS. The most commonly associated brain tumors include cortical tubers, subependymal nodules, and subependymal giant cell astrocytomas (SEGAs). The authors report an unusual case of recurrent meningitis due to a tuber-containing encephalocele via the posterior wall of the frontal sinus. An 11-year-old girl presented with a history of TSC and previous SEGA resection via interhemispheric approach. She presented twice within 4 months with classic bacterial meningitis. Cerebrospinal fluid cultures revealed Streptococcus pneumoniae. Computed tomography and MR imaging of the brain showed a right frontal sinus encephalocele via a posterior frontal sinus wall defect. Both episodes of meningitis were treated successfully with standard regimens of intravenous antibiotics. The neurosurgical service was consulted to discuss surgical options. Via a bicoronal incision, a right basal frontal craniotomy was performed. A large frontal encephalocele was encountered in the frontal sinus. The encephalocele was herniating through a bony defect of the posterior sinus wall. The encephalocele was ligated and resected followed by removing frontal sinus mucosa and complete cranialization of frontal sinus. Repair of the sinus floor was conducted with fat and pericranial grafts followed by CSF diversion via lumbar drain. Histopathology of the resected encephalocele showed a TSC tuber covered with respiratory (frontal sinus) mucosa. Tuber cells were diffusely positive for GFAP. The patient underwent follow-up for 2 years without evidence of recurrent meningitis or CSF rhinorrhea. This report demonstrates that frontal tubers of TSC can protrude into the frontal sinus as acquired encephaloceles and present with recurrent meningitis. To the authors' knowledge, recurrent meningitis is not known to coincide with TSC. Careful clinical and radiographic follow-up for frontal tubers in patients with TSC is

  14. Collision Analysis for MS DEXTRA

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Zhang, Shengming

    1999-01-01

    and grounding events have to be analysed and assessed.The present paper outlines such a rational procedure for evaluation of the probabilistic distribution of damages caused by collisions against other ships for a specific ship on a specific route.The work described in the paper constitutes a step towards...

  15. Cern collisions light up Copenhagen

    CERN Multimedia

    Banks, Michael

    2010-01-01

    "Anyone passing by the Niels Bohr Institute in Copenhagen, Denmark, might be startled by some strange moving lights on the facade of the institute's main building. In fact, the dancing beams show, almost in real time, collisions form the Atlas experiment at Cern's Large Hadron Collider (LHC)" (1 paragraph)

  16. Perspective on relativistic nuclear collisions

    Energy Technology Data Exchange (ETDEWEB)

    Glendenning, N.K.

    1979-05-01

    The importance of experiments detecting more than one particle is pointed out. The production of nuclei far from stability in peripheral collisions and the expectations for the explosive disassembly of dense nuclear matter (nuclear fireball) and some evidence for it are related. Pion interferometry concerns the measurement of correlations in the momentum and energy of two identical pions; the subject is discussed in relation to incoherent production, coherent production, partially coherent production, final-state interactions, impact parameter average, and outlook. Much of the paper deals with an assessment of the possibility of determining the form of the hadronic spectrum in the high-mass region through nuclear collisions at ultrarelativistic energies. The subject is developed under the following topics: perspective, the initial fireball, isoergic equilibrium expansion of the fireball, quasi-dynamical expansion, quark matter, and the mass degree of freedom. The quasi-dynamical model obtained indicates that certain parameters, such as the ..pi../N and K/N ratios at high kinetic energy, will survive the collision; therefore, a determination of the asymptotic form of the hadron spectrum probably can be made by studying nuclear collisions at very high energies (10 GeV/nucleon in the center of mass). 16 figures. (RWR)

  17. in heavy-ion collisions

    Indian Academy of Sciences (India)

    2015-05-06

    May 6, 2015 ... the 'Big Bang', and has now been (re-)created as the hottest matter ever in laboratory by heavy-ion collisions ('Little Bang') at the Relativistic Heavy Ion Collider (RHIC) as well as at the Large Hadron Collider (LHC). To experimentally measure and theoretically understand the various properties of the QGP ...

  18. Duration of an Elastic Collision

    Science.gov (United States)

    de Izarra, Charles

    2012-01-01

    With a pedagogical goal, this paper deals with a study of the duration of an elastic collision of an inflatable spherical ball on a planar surface suitable for undergraduate studies. First, the force generated by the deformed spherical ball is obtained under assumptions that are discussed. The study of the motion of the spherical ball colliding…

  19. Outer Dynamics of Ship Collisions

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose of these notes is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisons with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding...

  20. Influence of Hub Parameters on Joining Forces and Torque Transmission Output of Plastically-Joined Shaft-Hub-Connections with a Knurled Contact Surface

    Directory of Open Access Journals (Sweden)

    Lukáš Suchý

    2018-04-01

    Full Text Available A knurled interference fit is a machine part connection made by a plastic joining, which includes the advantages of commonly-used shaft-hub-connections. The combination of the friction and form fit, which are responsible for torque transmission, results in a higher power density than conventional connections. In this paper, parameter gaps are bridged with the aim of enhance the design calculation of the knurled interference fit. Experimental investigations on the shaft chamfer angle (100Cr6 and hub-diameter-ratio (AlSi1MgMn were performed. The analytical approaches are developed for calculating the joining force and maximal torque capacity by accounting for experimentally investigated loss of load transmission at high hub-diameter-ratios and high shaft chamfer angles. The presented calculation approach is an accurate tool for the assessment of early machine designs of the knurled interference fit and helps to save from having to perform time-extensive tests.

  1. Mesomechanical aspects of computational modeling for non-homogeneous materials joined by forming

    Directory of Open Access Journals (Sweden)

    Yunan Prawoto

    2017-01-01

    Full Text Available The metal forming and joining industries are constantly evolving to adapt to new materials and alloys and to meet customers’ needs. However, the size of the companies in this segment is typically small. Therefore, the progress of the mesomechanical modeling on non-homogeneous materials is relatively slow. This article aims to contribute to the advancement of such computational idea. The industries and academics alike may benefit the mesomechanical aspects of computational modeling for materials joined by forming using the established theories known in the field of mechanics. It may be used as an introductory for the society of joining by forming. This article reviews the basic concept of the finite element method, the fundamental mechanics and highlights some common problems in joining by forming, namely contact problems, local variations and interfacial cracking. This article aims to disseminate the meso/micro-mechanics approach to the field of joining by forming, which currently is dominated by experimental works and macroscopic modeling. Using the simple approaches discussed in this article, researchers with little or no background in computational mechanics can implement the concepts.

  2. Frontal EEG asymmetry in borderline personality disorder is associated with alexithymia.

    Science.gov (United States)

    Flasbeck, Vera; Popkirov, Stoyan; Brüne, Martin

    2017-01-01

    Frontal EEG asymmetry is a widely studied correlate of emotion processing and psychopathology. Recent research suggests that frontal EEG asymmetry during resting state is related to approach/withdrawal motivation and is also found in affective disorders such as major depressive disorder. Patients with borderline personality disorder (BPD) show aberrant behavior in relation to both approach and withdrawal motivation, which may arguably be associated with their difficulties in emotion processing. The occurrence and significance of frontal EEG asymmetry in BPD, however, has received little attention. Thirty-seven BPD patients and 39 controls underwent resting EEG and completed several psychometric questionnaires. While there were no between-group differences in frontal EEG asymmetry, in BPD frontal EEG asymmetry scores correlated significantly with alexithymia. That is, higher alexithymia scores were associated with relatively lower right-frontal activity. A subsequent analysis corroborated the significant interaction between frontal EEG asymmetry and alexithymia, which was moderated by group. Our findings reveal that lower right frontal EEG asymmetry is associated with alexithymia in patients with BPD. This finding is in accordance with neurophysiological models of alexithymia that implicate a right hemisphere impairment in emotion processing, and could suggest frontal EEG asymmetry as a potential biomarker of relevant psychopathology in these patients.

  3. Obsessions appear after the removal a brain tumor in the right frontal lobe.

    Science.gov (United States)

    Liu, Jie; Zhang, Xinhua; Liu, Jihua

    2014-01-01

    A series of case reports and neuroimaging research points to the underlying neuropathological substrate for obsessive-compulsive disorder (OCD) and the underlying associations between OCD and areas of the frontal lobe. We report a patient wherein the onset of OCD occurred after resection of meningioma of the right frontal lobe and who was treated successfully with paroxetine hydrochloride. We suggest that the onset of secondary (organic) OCD is associated with the frontal lobe, and we propose that the origin of obsessions is located in the right frontal lobe. Copyright © 2014 Elsevier Inc. All rights reserved.

  4. Optimal Placement of Cerebral Oximeter Monitors to Avoid the Frontal Sinus as Determined by Computed Tomography.

    Science.gov (United States)

    Gregory, Alexander J; Hatem, Muhammed A; Yee, Kevin; Grocott, Hilary P

    2016-01-01

    To determine the optimal location to place cerebral oximeter optodes to avoid the frontal sinus, using the orbit of the skull as a landmark. Retrospective observational study. Academic hospital. Fifty adult patients with previously acquired computed tomography angiography scans of the head. The distance between the superior orbit of the skull and the most superior edge of the frontal sinus was measured using imaging software. The mean (SD) frontal sinus height was 16.4 (7.2) mm. There was a nonsignificant trend toward larger frontal sinus height in men compared with women (p = 0.12). Age, height, and body surface area did not correlate with frontal sinus height. Head circumference was positively correlated (r = 0.32; p = 0.03) to frontal sinus height, with a low level of predictability based on linear regression (R(2) = 0.10; p = 0.02). Placing cerebral oximeter optodes>3 cm from the superior rim of the orbit will avoid the frontal sinus in>98% of patients. Predicting the frontal sinus height based on common patient variables is difficult. Additional studies are required to evaluate the recommended height in pediatric populations and patients of various ethnic backgrounds. The clinical relevance of avoiding the frontal sinus also needs to be further elucidated. Copyright © 2016 Elsevier Inc. All rights reserved.

  5. DHEA and frontal fibrosing alopecia: molecular and physiopathological mechanisms.

    Science.gov (United States)

    Gaspar, Neide Kalil

    2016-01-01

    The transforming growth factor-beta 1 (TGFβ1) promotes fibrosis, differentiating epithelial cells and quiescent fibroblasts into myofibroblasts and increasing expression of extracellular matrix. Recent investigations have shown that PPAR (peroxisome proliferator-activated receptor*) is a negative regulator of fibrotic events induced by TGFβ1. Dehydroepiandrosterone (DHEA) is an immunomodulatory hormone essential for PPAR functions, and is reduced in some processes characterized by fibrosis. Although scarring alopecia characteristically develops in the female biological period in which occurs decreased production of DHEA, there are no data in the literature relating its reduction to fibrogenic process of this condition. This article aims to review the fibrogenic activity of TGFβ1, its control by PPAR and its relation with DHEA in the frontal fibrosing alopecia.

  6. Lóbulo Frontal y Psicoanálisis

    Directory of Open Access Journals (Sweden)

    Edmundo Beteta

    1994-06-01

    Full Text Available Se trata de establecer mediante una atractiva hipótesis de trabajo, las relaciones entre los lóbulo frontales y las bases neurobiológicas de la teoría freudiana del psicoanálisis. Se presenran y discuten las aproximaciones psicofisiológicas y clínicas, en la interpretación de estas relaciones, llegando al análisis final de las "disoluciones" orgánicas y funcionales del cerebro, pasando revista a los síntomas de la demencia y cuadros clínicos diferenciales, por los cuales se puede llegar a la interpretación freudiana de la psicopatía, la farmacodependencia y el síndrome del terrorismo.

  7. Evaluation of galectin binding by frontal affinity chromatography (FAC).

    Science.gov (United States)

    Iwaki, Jun; Hirabayashi, Jun

    2015-01-01

    Frontal affinity chromatography (FAC) is a simple and versatile procedure enabling quantitative determination of diverse biological interactions in terms of dissociation constants (K d), even though these interactions are relatively weak. The method is best applied to glycans and their binding proteins, with the analytical system operating on the basis of highly reproducible isocratic elution by liquid chromatography. Its application to galectins has been successfully developed to characterize their binding specificities in detail. As a result, their minimal requirements for recognition of disaccharides, i.e., β-galactosides, as well as characteristic features of individual galectins, have been elucidated. In this chapter, we describe standard procedures to determine the K d's for interactions between a series of standard glycans and various galectins.

  8. Evidence of Mirror Neurons in Human Inferior Frontal Gyrus

    Science.gov (United States)

    Kilner, James M.; Neal, Alice; Weiskopf, Nikolaus; Friston, Karl J.; Frith, Chris D.

    2009-01-01

    There is much current debate about the existence of mirror neurons in humans. To identify mirror neurons in the inferior frontal gyrus (IFG) of humans we employed a repetition suppression paradigm while measuring neural activity with functional magnetic resonance imaging. Subjects either executed or observed a series of actions. Here we show that in the IFG, responses were suppressed both when an executed action was followed by the same rather than a different observed action and when an observed action was followed by the same rather than a different executed action. This pattern of responses is consistent with that predicted by mirror neurons and is evidence of mirror neurons in the human IFG. PMID:19675249

  9. Passenger head in impact with frontal airbag in OOP postures

    Science.gov (United States)

    Ovidiu Soica, Adrian; Toganel, George-Radu

    2017-10-01

    Road accidents represent an aspect of road traffic that may lead negative consequences. In order to solve the problems associated with such events, interdisciplinary knowledge is called for, complex teams of engineers, doctors, lawyers, experts working together in order to reduce the severity of such events. Road safety is a continuous concern for both experts and various government organizations with the aim of protecting the lives of the participants in traffic. It has been estimated that the costs of traffic accidents account for 1-3% of a country GDP, depending on the level of country development [26]. In this paper we analyze a particular class of cases of injuries caused to passengers caused by the inflation of the frontal airbag when they are with the passenger out of position. Head kinematics, accelerations, as well as the severity of injuries expressed by HIC, as related to the AIS scale have been analysed.

  10. Cholinergic receptor binding in the frontal cortex of suicide victims

    International Nuclear Information System (INIS)

    Stanley, M.

    1986-01-01

    Because there is a high incidence of individuals diagnosed as having an affective disorder who subsequently commit suicide, the author thought it would be of interest to determine QNB binding in the brains of a large sample of suicide victims, and to compare the findings with a well-matched control group. Brain samples were obtained at autopsy from 22 suicide victims and 22 controls. Frontal cortex samples were diseected, frozen, and stored until assayed. Samples of tissue homogenate were incubated in duplicate with 10 concentrations of tritium-QNB. Specific binding was determined with and without atropine. The results confirmed previous studies in which no changes were noted in suicide versus control brains. While the findings neither disprove nor support the cholinergic hypothesis of depression, they do suggest that the neurochemical basis for the in vivo observations of increased responsivity of depressed individuals to muscarinic cholinergic agents might not involve changes in receptors estimated by QNB binding

  11. Nocturnal frontal lobe epilepsy presenting as excessive daytime sleepiness

    Directory of Open Access Journals (Sweden)

    Jocelyn Y Cheng

    2013-01-01

    Full Text Available Excessive daytime sleepiness (EDS is common in the general population. Etiologies include insufficient sleep and primary sleep disorders. Due to its high prevalence, physicians often overlook EDS as a significant problem. However, EDS may also be the presenting symptom of seizures, in particular Nocturnal Frontal Lobe Epilepsy (NFLE. Due to the clinical similarity between the nocturnal behaviors of NFLE and parasomnias, and poor patient-related history, NFLE remains a challenging diagnosis. We report the case of a patient with NFLE who presented with a primary complaint of EDS, and discuss the differential diagnosis and evaluation of patients with EDS associated with nocturnal behaviors. In the context of a patient presenting with EDS and stereotyped nocturnal events, clinical suspicion should be high for NFLE.

  12. Laser-assisted atom-atom collisions

    International Nuclear Information System (INIS)

    Roussel, F.

    1984-01-01

    The basic layer-assisted atom-atom collision processes are reviewed in order to get a simpler picture of the main physical facts. The processes can be separated into two groups: optical collisions where only one atom is changing state during the collision, the other acting as a spectator atom, and radiative collisions where the states of the two atoms are changing during the collision. All the processes can be interpreted in terms of photoexcitation of the quasimolecule formed during the collisional process. (author)

  13. Reversed Procrastination by Focal Disruption of Medial Frontal Cortex.

    Science.gov (United States)

    Jha, Ashwani; Diehl, Beate; Scott, Catherine; McEvoy, Andrew W; Nachev, Parashkev

    2016-11-07

    An enduring puzzle in the neuroscience of voluntary action is the origin of the remarkably wide dispersion of the reaction time distribution, an interval far greater than is explained by synaptic or signal transductive noise [1, 2]. That we are able to change our planned actions-a key criterion of volition [3]-so close to the time of their onset implies decision-making must reach deep into the execution of action itself [4-6]. It has been influentially suggested the reaction time distribution therefore reflects deliberate neural procrastination [7], giving alternative response tendencies sufficient time for fair competition in pursuing a decision threshold that determines which one is behaviorally manifest: a race model, where action selection and execution are closely interrelated [8-11]. Although the medial frontal cortex exhibits a sensitivity to reaction time on functional imaging that is consistent with such a mechanism [12-14], direct evidence from disruptive studies has hitherto been lacking. If movement-generating and movement-delaying neural substrates are closely co-localized here, a large-scale lesion will inevitably mask any acceleration, for the movement itself could be disrupted. Circumventing this problem, here we observed focal intracranial electrical disruption of the medial frontal wall in the context of the pre-surgical evaluation of two patients with epilepsy temporarily reversing such hypothesized procrastination. Effector-specific behavioral acceleration, time-locked to the period of electrical disruption, occurred exclusively at a specific locus at the ventral border of the pre-supplementary motor area. A cardinal prediction of race models of voluntary action is thereby substantiated in the human brain. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  14. Cytoarchitecture, probability maps and functions of the human frontal pole.

    Science.gov (United States)

    Bludau, S; Eickhoff, S B; Mohlberg, H; Caspers, S; Laird, A R; Fox, P T; Schleicher, A; Zilles, K; Amunts, K

    2014-06-01

    The frontal pole has more expanded than any other part in the human brain as compared to our ancestors. It plays an important role for specifically human behavior and cognitive abilities, e.g. action selection (Kovach et al., 2012). Evidence about divergent functions of its medial and lateral part has been provided, both in the healthy brain and in psychiatric disorders. The anatomical correlates of such functional segregation, however, are still unknown due to a lack of stereotaxic, microstructural maps obtained in a representative sample of brains. Here we show that the human frontopolar cortex consists of two cytoarchitectonically and functionally distinct areas: lateral frontopolar area 1 (Fp1) and medial frontopolar area 2 (Fp2). Based on observer-independent mapping in serial, cell-body stained sections of 10 brains, three-dimensional, probabilistic maps of areas Fp1 and Fp2 were created. They show, for each position of the reference space, the probability with which each area was found in a particular voxel. Applying these maps as seed regions for a meta-analysis revealed that Fp1 and Fp2 differentially contribute to functional networks: Fp1 was involved in cognition, working memory and perception, whereas Fp2 was part of brain networks underlying affective processing and social cognition. The present study thus disclosed cortical correlates of a functional segregation of the human frontopolar cortex. The probabilistic maps provide a sound anatomical basis for interpreting neuroimaging data in the living human brain, and open new perspectives for analyzing structure-function relationships in the prefrontal cortex. The new data will also serve as a starting point for further comparative studies between human and non-human primate brains. This allows finding similarities and differences in the organizational principles of the frontal lobe during evolution as neurobiological basis for our behavior and cognitive abilities. Copyright © 2013 Elsevier Inc. All

  15. A frontal but not parietal neural correlate of auditory consciousness.

    Science.gov (United States)

    Brancucci, Alfredo; Lugli, Victor; Perrucci, Mauro Gianni; Del Gratta, Cosimo; Tommasi, Luca

    2016-01-01

    Hemodynamic correlates of consciousness were investigated in humans during the presentation of a dichotic sequence inducing illusory auditory percepts with features analogous to visual multistability. The sequence consisted of a variation of the original stimulation eliciting the Deutsch's octave illusion, created to maintain a stable illusory percept long enough to allow the detection of the underlying hemodynamic activity using functional magnetic resonance imaging (fMRI). Two specular 500 ms dichotic stimuli (400 and 800 Hz) presented in alternation by means of earphones cause an illusory segregation of pitch and ear of origin which can yield up to four different auditory percepts per dichotic stimulus. Such percepts are maintained stable when one of the two dichotic stimuli is presented repeatedly for 6 s, immediately after the alternation. We observed hemodynamic activity specifically accompanying conscious experience of pitch in a bilateral network including the superior frontal gyrus (SFG, BA9 and BA10), medial frontal gyrus (BA6 and BA9), insula (BA13), and posterior lateral nucleus of the thalamus. Conscious experience of side (ear of origin) was instead specifically accompanied by bilateral activity in the MFG (BA6), STG (BA41), parahippocampal gyrus (BA28), and insula (BA13). These results suggest that the neural substrate of auditory consciousness, differently from that of visual consciousness, may rest upon a fronto-temporal rather than upon a fronto-parietal network. Moreover, they indicate that the neural correlates of consciousness depend on the specific features of the stimulus and suggest the SFG-MFG and the insula as important cortical nodes for auditory conscious experience.

  16. Study of frontal weather system using satellite images

    International Nuclear Information System (INIS)

    Qureshi, J.; Ershad, S.

    2005-01-01

    Pakistan which is situated in the south Asian sub continent, has a peculiar climatological position. It is one of the few countries in the world, which undergo a complete transformation from summer to winter season. However this project only pertains to the winter weather conditions in Pakistan. During winter, the land masses cool off rapidly as compared to the seas and so high pressure cells are developed over land causing, weak anti-cyclonic circulation over the country. In between these cells of anti-cyclonic flow of wind, there are zones of convergence, which offer a good breeding place for low-pressure waves. The low-pressure waves are similar to the extra tropical depressions and approach and approach Pakistan from west. From the same reason these are locally called the western Disturbances. Consequently the focus of study is on the extra tropical cyclones which originate along the boundary between polar continental and tropical or polar maritime and tropical maritime air masses. The extra tropical cyclones (also called western disturbances and westerly waves.) which are embedded in westerly flow of air move across north of Pakistan are usually originate from the Mediterranean sea. These systems consist of two types of fronts i.e. warm and cold fronts. In fact these systems can be traced right from the Atlantic Ocean and Mediterranean Sea. The location of frontal weather is generally associated with the surrounding synoptic situation, geographical position of the westerly wave, location of subtropical jet stream, steering wind level etc. although the satellite imageries are quite helpful for forecasting the frontal weather over our region however the weather charts (both surface and upper air ) and jet maps are also very helpful for this purpose

  17. Using time-to-contact information to assess potential collision modulates both visual and temporal prediction networks

    Directory of Open Access Journals (Sweden)

    Jennifer T Coull

    2008-09-01

    Full Text Available Accurate estimates of the time-to-contact (TTC of approaching objects are crucial for survival. We used an ecologically valid driving simulation to compare and contrast the neural substrates of egocentric (head-on approach and allocentric (lateral approach TTC tasks in a fully factorial, event-related fMRI design. Compared to colour control tasks, both egocentric and allocentric TTC tasks activated left ventral premotor cortex/frontal operculum and inferior parietal cortex, the same areas that have previously been implicated in temporal attentional orienting. Despite differences in visual and cognitive demands, both TTC and temporal orienting paradigms encourage the use of temporally predictive information to guide behaviour, suggesting these areas may form a core network for temporal prediction. We also demonstrated that the temporal derivative of the perceptual index tau (tau-dot held predictive value for making collision judgements and varied inversely with activity in primary visual cortex (V1. Specifically, V1 activity increased with the increasing likelihood of reporting a collision, suggesting top-down attentional modulation of early visual processing areas as a function of subjective collision. Finally, egocentric viewpoints provoked a response bias for reporting collisions, rather than no-collisions, reflecting increased caution for head-on approaches. Associated increases in SMA activity suggest motor preparation mechanisms were engaged, despite the perceptual nature of the task.

  18. Influence of friction stir welding parameters on titanium-aluminum heterogeneous lap joining configuration

    Science.gov (United States)

    Picot, Florent; Gueydan, Antoine; Hug, Éric

    2017-10-01

    Lap joining configuration for Friction Stir Welding process is a methodology mostly dedicated to heterogeneous bonding. This welding technology was applied to join pure titanium with pure aluminum by varying the rotation speed and the movement speed of the tool. Regardless of the process parameters, it was found that the maximum strength of the junction remains almost constant. Microstructural observations by means of Scanning Electron Microscopy and Energy Dispersive Spectrometry analysis enable to describe the interfacial join and reveal asymmetric Cold Lap Defects on the sides of the junction. Chemical analysis shows the presence of one exclusive intermetallic compound through the interface identified as TiAl3. This compound is responsible of the crack spreading of the junction during the mechanical loading. The original version of this article supplied to AIP Publishing contained an accidental inversion of the authors, names. An updated version of this article, with the authors names formatted correctly was published on 20 October 2017.

  19. Joining of silicon carbide using interlayer with matching coefficient of thermal expansion

    Energy Technology Data Exchange (ETDEWEB)

    Perham, T. [Univ. of California, Berkeley, CA (United States). Dept. of Materials Science and Mineral Engineering]|[Lawrence Berkeley National Lab., CA (United States)

    1996-11-01

    The primary objective of this study is to develop a technique for joining a commercially available Silicon Carbide that gives good room temperature strength and the potential for good high temperature strength. One secondary objective is that the joining technique be adaptable to SiC{sub f}/SiC composites and/or Nickel based superalloys, and another secondary objective is that the materials provide good neutron irradiation resistance and low activation for potential application inside nuclear fusion reactors. The joining techniques studied here are: (1) reaction bonding with Al-Si/Si/SiC/C; (2) reaction/infiltration with calcium aluminum silicate; (3) ion exchange mechanism to form calcium hexaluminate (a refractory cement); and (4) oxide frit brazing with cordierite.

  20. Investigating the joining of PMMA plastic to steel by Nd:YAG laser

    Directory of Open Access Journals (Sweden)

    Andor Bauernhuber

    2012-09-01

    Full Text Available Due to the effort of weight reduction in the manufacturing of vehicles, the application and therefore the joining of different materials such as plastics and metals play more and more important role in the development of the joining processes nowadays. In this research work, the joining of PMMA plastic sheets and unalloyed steel pins was investigated. The authors applied Nd:YAG laser beam to create the bond, and tensile tests were carried out to analyse how the strength of the joint is influenced by the heating time, the penetration depth of the steel workpieces in the plastic and the surface roughness of steel. The observed bubble formation and the tearing characteristics were also studied.

  1. Joining of silicon carbide using interlayer with matching coefficient of thermal expansion

    International Nuclear Information System (INIS)

    Perham, T.

    1996-11-01

    The primary objective of this study is to develop a technique for joining a commercially available Silicon Carbide that gives good room temperature strength and the potential for good high temperature strength. One secondary objective is that the joining technique be adaptable to SiC f /SiC composites and/or Nickel based superalloys, and another secondary objective is that the materials provide good neutron irradiation resistance and low activation for potential application inside nuclear fusion reactors. The joining techniques studied here are: (1) reaction bonding with Al-Si/Si/SiC/C; (2) reaction/infiltration with calcium aluminum silicate; (3) ion exchange mechanism to form calcium hexaluminate (a refractory cement); and (4) oxide frit brazing with cordierite

  2. Characterization of joining sites of a viral histone H4 on host insect chromosomes.

    Directory of Open Access Journals (Sweden)

    Sunil Kumar

    Full Text Available A viral histone H4 (CpBV-H4 is encoded in a polydnavirus, Cotesia plutellae bracovirus (CpBV. It plays a crucial role in parasitism of an endoparasitoid wasp, C. plutellae, against diamondback moth, Plutella xylostella, by altering host gene expression in an epigenetic mode by its N-terminal tail after joining host nucleosomes. Comparative transcriptomic analysis between parasitized and nonparasitized P. xylostella by RNA-Seq indicated that 1,858 genes were altered at more than two folds in expression levels at late parasitic stage, including 877 up-regulated genes and 981 down-regulated genes. Among parasitic factors altering host gene expression, CpBV-H4 alone explained 16.3% of these expressional changes. To characterize the joining sites of CpBV-H4 on host chromosomes, ChIP-Seq (chromatin immunoprecipitation followed by deep sequencing was applied to chromatins extracted from parasitized larvae. It identified specific 538 ChIP targets. Joining sites were rich (60.2% in AT sequence. Almost 40% of ChIP targets included short nucleotide repeat sequences presumably recognizable by transcriptional factors and chromatin remodeling factors. To further validate these CpBV-H4 targets, CpBV-H4 was transiently expressed in nonparasitized host at late larval stage and subjected to ChIP-Seq. Two kinds of ChIP-Seqs shared 51 core joining sites. Common targets were close (within 1 kb to genes regulated at expression levels by CpBV-H4. However, other host genes not close to CpBV-H4 joining sites were also regulated by CpBV-H4. These results indicate that CpBV-H4 joins specific chromatin regions of P. xylostella and controls about one sixth of the total host genes that were regulated by C. plutellae parasitism in an epigenetic mode.

  3. Using Negotiated Joining to Construct and Fill Open-ended Roles in Elite Culinary Groups.

    Science.gov (United States)

    Tan, Vaughn

    2015-03-01

    This qualitative study examines membership processes in groups operating in an uncertain environment that prevents them from fully predefining new members' roles. I describe how nine elite high-end, cutting-edge culinary groups in the U.S. and Europe, ranging from innovative restaurants to culinary R&D groups, use negotiated joining-a previously undocumented process-to systematically construct and fill these emergent, open-ended roles. I show that negotiated joining is a consistently patterned, iterative process that begins with a role that both aspirant and target group explicitly understand to be provisional. This provisional role is then jointly modified and constructed by the aspirant and target group through repeated iterations of proposition, validation through trial and evaluation, and selective integration of validated role components. The initially provisional role stabilizes and the aspirant achieves membership if enough role components are validated; otherwise the negotiated joining process is abandoned. Negotiated joining allows the aspirant and target group to learn if a mutually desirable role is likely and, if so, to construct such a role. In addition, the provisional roles in negotiated joining can support absorptive capacity by allowing novel role components to enter target groups through aspirants' efforts to construct stable roles for themselves, while the internal adjustment involved in integrating newly validated role components can have the unintended side effect of supporting adaptation by providing opportunities for the groups to use these novel role components to modify their role structure and goals to suit a changing and uncertain environment. Negotiated joining thus reveals role ambiguity's hitherto unexamined beneficial consequences and provides a foundation for a contingency theory of new-member acquisition.

  4. Performance of electro-plated and joined components for divertor application

    International Nuclear Information System (INIS)

    Krauss, Wolfgang; Lorenz, Julia; Konys, Jürgen

    2013-01-01

    Highlights: • Active interlayers of Ni and Pd were electroplated on W to assist joining. • Demonstrator types of W-steel and W–W joints were successfully fabricated. • Diffusion processes increase operation temperature above brazing temperature. • Ni electro-plating is less sensitive to variation of deposition parameters than Pd. • Shear tests showed values in resistance comparable to those of commercial fillers. -- Abstract: A general challenge in divertor development, independently of design type and cooling medium water or helium, is the reliable and adapted joining of components. Depending on the design variants, the characteristics of the joints will be focused on functional or structural behavior to guarantee e.g. good thermal conductivity and sufficient mechanical strength. All variants will have in common that tungsten is the plasma facing material. Thus, material combinations to be joined will range from Cu base over steel to tungsten. Especially tungsten shows lacks in adapted joining due to its metallurgical behavior ranging from immiscibility over bad wetting up to brittle intermetallic phase formation. Joining assisted by electro-chemical deposition of functional and filler layers showed that encouraging progress was achieved in wetting applying nickel interlayers. Nickel proved to be a good reference material but alternative elements (e.g. Pd, Fe) may be more attractive in fusion to manufacture suitable joints. Replacing of Ni as activator element by Pd for W/W or W/steel joints was achieved and joining with Cu-filler was successfully performed. Manufactured joints were characterized applying metallurgical testing and SEM/EDX analyses demonstrating the applicability of Pd activator. First shear tests showed that the joints exhibit mechanical stability sufficient for technical application

  5. Effect of chemical stimulation of the medial frontal lobe on the micturition reflex in rats.

    Science.gov (United States)

    Nishijima, Saori; Sugaya, Kimio; Kadekawa, Katsumi; Ashitomi, Katsuhiro; Yamamoto, Hideyuki

    2012-03-01

    We assessed the influence of the medial frontal lobe on micturition after chemical stimulation. We also examined the relation between the medial frontal lobe and the rostral pontine reticular formation, which has a strong inhibitory effect on micturition. A total of 35 female rats underwent continuous cystometry. Bladder activity changes were examined after physiological saline, glutamate, the glutamate receptor antagonist MK-801, noradrenaline or the adrenergic α-1 receptor antagonist naftopidil was injected in the medial frontal lobe. When glutamate was injected in the medial frontal lobe, MK-801 was also injected in the rostral pontine reticular formation. Glutamate injection in the medial frontal lobe prolonged the interval between bladder contractions while injection of the glutamate antagonist MK-801 shortened the interval. Glutamate injection in the medial frontal lobe just after MK-801 injection in the ipsilateral rostral pontine reticular formation also prolonged the interval between bladder contractions. However, after prior injection of MK-801 in the bilateral rostral pontine reticular formation glutamate injection in the medial frontal lobe did not influence cystometric parameters. Noradrenaline injection in the medial frontal lobe shortened the interval between bladder contractions while injection of its antagonist naftopidil prolonged the interval. Medial frontal lobe neurons excited by glutamate inhibited the micturition reflex via activation of the rostral pontine reticular formation by glutamatergic projection while medial frontal lobe neurons excited by noradrenaline facilitated the micturition reflex. Thus, the medial frontal lobe may be an important integration center for the initiation of micturition and urine storage mechanisms. Copyright © 2012 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

  6. Thermally joining and/or coating or thermally separating the workpieces having heat-sensitive coating, comprises restoring coating by thermally coating the coating material after thermally joining and/or coating or thermally separating

    OpenAIRE

    Riedel, Frank; Winkelmann, Ralf; Puschmann, Markus

    2011-01-01

    The method for thermally joining and/or coating or thermally separating the workpieces (1), which have a heat-sensitive coating (2), comprises restoring the coating by thermally coating a coating material (3) after thermally joining and/or coating or thermally separating the workpieces. A part of the thermal energy introduced in the workpiece for joining and/or coating or separating or in the workpieces is used for thermally coating the coating material. Two workpieces are welded or soldered ...

  7. POSSIBILITY OF PHARMACOMODULATION OF THE HYPERSENSITIVE RHINITIS JOINED WITH THE NASAL POLYPOSIS

    Directory of Open Access Journals (Sweden)

    Dejan Ursulović

    2001-11-01

    Full Text Available The research goai is to examine the effects of the local corticosteroidapplication to the number of eosinophils in the nasal secretion of the patients withhypersensitive rhinitis joined with the nasal polyposis. The study comprises 13patients with hypersensitive rhinitis joined with the nasal polyposis; 9 of them madeup the experimental group. The local corticosteroid (bechomethasone dipropionatein water spray was given at 12 hours in individual doses of 200 micrograms to theexperimental group patients in six weeks. During the treatment it was confirmed thatthere was a highly important reduction of the number of eosinophils of the nasalsecretion in the experimental group patients.

  8. [Joining WHO of Republic of Korea and the projects in the 1950s].

    Science.gov (United States)

    Lee, Sun Ho

    2014-04-01

    The Republic of Korea(ROK) and the World Health Organization(WHO) have done many projects successfully from 1949, in which the government of First Republic joined the WHO. However the relation between the ROK and the WHO have not been studied very much so far. The main purpose of this research, which could be done by the support of WHO, is connected with three questions. First research point would be "how could the ROK joined WHO in 1949 and what's the meaning of it? And the what's the difference in the process for the WHO between the ROK of 1949 and the DPRK(Democratic People's Republic of Korea) of 1973?" The first president of the ROK, Rhee Syngman, who had received his Ph. D.(about international politics) from Princeton University in 1910, was strongly interested in joining international institutes like UN, WHO. The ROK that could join WHO on 17 August 1949, with the approval of Assembly on 25 May 1949, was one of the founder members of the Western Pacific Region. By joining WHO, the ROK could get chance to increase the level of public health and its administration in 1950's. But the DPRK manage to became a member of WHO on 19 May 1973 and joined the South-East Asia Region. The joining of DPRK was influenced by the easing of the cold war after the Nixon Doctrine and the joining of the China(People's Republic of China). Second research point would be "What kind of roll did the WHO take in the First Republic?" Yet the public health administration of the First Republic that had been made in the period of US army military government was been strongly influenced by USA, the roll of WHO was also important in the 1950's. Last research point would be "What kind of the projects did the ROK and the WHO take part in during the period of he First Republic? How could evaluate the results?" The ROK and the WHO handled the projects including health services, communicable disease prevention and control, control of noncommunicable diseases, and protection of health. Specially

  9. Distinct DNA repair pathways involving RecA and nonhomologous end joining in Mycobacterium smegmatis.

    OpenAIRE

    Korycka-Machala, M; Brzostek, A; Rozalska, S; Rumijowska-Galewicz, A; Dziedzic, R; Bowater, R; Dziadek, J

    2006-01-01

    Mycobacterium smegmatis was used to study the relationship between DNA repair processes involving RecA and nonhomologous end joining (NHEJ). The effect of gene deletions in recA and/or in two genes involved in NHEJ (ku and ligD) was tested on the ability of bacteria to join breaks in plasmids transformed into them and in their response to chemicals that damage DNA. The results provide in vivo evidence that only NHEJ is required for the repair of noncompatible DNA ends. By contrast, the respon...

  10. Distinct DNA repair pathways involving RecA and nonhomologous end joining in Mycobacterium smegmatis.

    Science.gov (United States)

    Korycka-Machala, Malgorzata; Brzostek, Anna; Rozalska, Sylwia; Rumijowska-Galewicz, Anna; Dziedzic, Renata; Bowater, Richard; Dziadek, Jaroslaw

    2006-05-01

    Mycobacterium smegmatis was used to study the relationship between DNA repair processes involving RecA and nonhomologous end joining (NHEJ). The effect of gene deletions in recA and/or in two genes involved in NHEJ (ku and ligD) was tested on the ability of bacteria to join breaks in plasmids transformed into them and in their response to chemicals that damage DNA. The results provide in vivo evidence that only NHEJ is required for the repair of noncompatible DNA ends. By contrast, the response of mycobacteria to mitomycin C preferentially involved a RecA-dependent pathway.

  11. Research and Development Opportunities for Joining Technologies in HVAC&R

    Energy Technology Data Exchange (ETDEWEB)

    William Goetzler, Matt Guernsey, Jim Young

    2015-10-01

    The Building Technologies Office (BTO) works with researchers and industry partners to develop and deploy technologies that can substantially reduce energy consumption and greenhouse gas (GHG) emissions in residential and commercial buildings. This opportunity assessment aims to advance BTO’s energy savings, GHG reduction, and other program goals by identifying research and development (R&D) initiatives for joining technologies in heating, ventilation, air-conditioning, and refrigeration (HVAC&R) systems. Improving joining technologies for HVAC&R equipment has the potential to increase lifetime equipment operating efficiency, decrease equipment and project cost, and most importantly reduce hydroflourocarbon (HFC) refrigerant leakage to support HFC phasedown and GHG reduction goals.

  12. COMPETITIVENESS ОF CHINESE ECONOMY AFTER JOINING WORLD TRADE ORGANIZATION

    Directory of Open Access Journals (Sweden)

    V. S. Shlik

    2008-01-01

    Full Text Available The paper contains analysis of the China’s membership in the World Trade Organization (WTO. The advantages and disadvantages of WTO joining and also prospects and unforeseen difficulties are given in the paper. The People’s Republic of China has already been a full-member of WTO for 6 years. The Chinese Government has mainly fulfilled all the conditions which were imposed for WTO joining. They concerned customs legislation that presupposed a considerable reduction of custom duties, an access to the service market for foreign investors, an increase of responsibility for violation of intellectual property rights. Many of these conditions have been fulfilled in advance.

  13. Hard probes in heavy ion collisions at the LHC: PDFs, shadowing and $pA$ collisions

    CERN Document Server

    Accardi, Alberto; Botje, M.; Brodsky, S.J.; Cole, B.; Eskola, K.J.; Fai, George I.; Frankfurt, L.; Fries, R.J.; Geist, Walter M.; Guzey, V.; Honkanen, H.; Kolhinen, V.J.; Kovchegov, Yu.V.; McDermott, M.; Morsch, A.; Qiu, Jian-wei; Salgado, C.A.; Strikman, M.; Takai, H.; Tapprogge, S.; Vogt, R.; Zhang, X.f.

    2003-01-01

    This manuscript is the outcome of the subgroup ``PDFs, shadowing and $pA$ collisions'' from the CERN workshop ``Hard Probes in Heavy Ion Collisions at the LHC''. In addition to the experimental parameters for $pA$ collisions at the LHC, the issues discussed are factorization in nuclear collisions, nuclear parton distributions (nPDFs), hard probes as the benchmark tests of factorization in $pA$ collisions at the LHC, and semi-hard probes as observables with potentially large nuclear effects. Also, novel QCD phenomena in $pA$ collisions at the LHC are considered. The importance of the $pA$ program at the LHC is emphasized.

  14. Parallel pathways from whisker and visual sensory cortices to distinct frontal regions of mouse neocortex.

    Science.gov (United States)

    Sreenivasan, Varun; Kyriakatos, Alexandros; Mateo, Celine; Jaeger, Dieter; Petersen, Carl C H

    2017-07-01

    The spatial organization of mouse frontal cortex is poorly understood. Here, we used voltage-sensitive dye to image electrical activity in the dorsal cortex of awake head-restrained mice. Whisker-deflection evoked the earliest sensory response in a localized region of primary somatosensory cortex and visual stimulation evoked the earliest responses in a localized region of primary visual cortex. Over the next milliseconds, the initial sensory response spread within the respective primary sensory cortex and into the surrounding higher order sensory cortices. In addition, secondary hotspots in the frontal cortex were evoked by whisker and visual stimulation, with the frontal hotspot for whisker deflection being more anterior and lateral compared to the frontal hotspot evoked by visual stimulation. Investigating axonal projections, we found that the somatosensory whisker cortex and the visual cortex directly innervated frontal cortex, with visual cortex axons innervating a region medial and posterior to the innervation from somatosensory cortex, consistent with the location of sensory responses in frontal cortex. In turn, the axonal outputs of these two frontal cortical areas innervate distinct regions of striatum, superior colliculus, and brainstem. Sensory input, therefore, appears to map onto modality-specific regions of frontal cortex, perhaps participating in distinct sensorimotor transformations, and directing distinct motor outputs.

  15. The functional role of individual-alpha based frontal asymmetry in stress responding

    NARCIS (Netherlands)

    Quaedflieg, C.W.E.M.; Meyer, T.; Smulders, F.T.Y.; Smeets, T.J.M.

    2015-01-01

    Asymmetry in frontal electrical activity has been suggested to index tendencies in affective responding and thus may be associated with hormonal stress responses. To assess the functional role of frontal asymmetry (FA) in stress, we measured FA at rest and following exposure to acute stress induced

  16. Clinico-Pathological Correlations of the Frontal Lobe Syndrome : Results of a Large Brain Bank Study

    NARCIS (Netherlands)

    Krudop, Welmoed A; Bosman, Sjanne; Geurts, Jeroen J G; Sikkes, Sietske A M; Verwey, Nicolaas A; Stek, Max L; Scheltens, Philip; Rozemuller, Annemieke J M; Pijnenburg, Yolande A L

    2015-01-01

    AIMS: A clinical frontal lobe syndrome (FLS) is generally attributed to functional or structural disturbances within frontal-subcortical circuits. We studied the distribution of pathological brain changes in FLS. Additionally, the prevalence of FLS among various disorders was studied. METHODS: We

  17. Mother and daughter with adolescent-onset severe frontal lobe dysfunction and epilepsy

    Science.gov (United States)

    dos Passos, Giordani Rodrigues; Fernández, Alonso Cuadrado; Vasques, Adriana Machado; Martins, William Alves; Palmini, André

    2016-01-01

    ABSTRACT Familial cases of early-onset prominent frontal lobe dysfunction associated with epilepsy have not been reported to date. We report a mother and her only daughter with incapacitating behavioral manifestations of frontal lobe dysfunction and epilepsy of variable severity. The possibility of a hitherto undescribed genetic condition is discussed. PMID:29213461

  18. Osteite frontale post-sinusitique: Etude rétrospective à propos de 31 ...

    African Journals Online (AJOL)

    Objective : Post-sinusitic frontal osteitis is defined as an extension of frontal sinus infection to the adjacent bony structures. It is an emergency that should rapidly be diagnosed and treated. The aim of this study is to analyze epidemiologic, clinical and paraclinical features, and to review different therapeutic modalities of this ...

  19. Inferior Frontal Gyrus Activity Triggers Anterior Insula Response to Emotional Facial Expressions

    NARCIS (Netherlands)

    Jabbi, Mbemba; Keysers, Christian

    2008-01-01

    The observation of movies of facial expressions of others has been shown to recruit similar areas involved in experiencing one's own emotions: the inferior frontal gyrus (IFG). the anterior insula and adjacent frontal operculum (IFO). The Causal link bet between activity in these 2 regions,

  20. Does depth of the frontal sinus affect near-infrared spectroscopy measurement?

    DEFF Research Database (Denmark)

    Holmgaard, Frederik; Vedel, Anne G; Langkilde, Annika

    2016-01-01

    Near-infrared spectroscopy (NIRS) is a non-invasive method that reflects real-time cerebral oxygenation (rSO2) by the use of two adhesive optodes placed on the forehead of the patient. Frontal sinuses vary anatomically and a large frontal sinus might compromise the NIRS signal since the NIRS...

  1. Visuo-spatial construction in patients with frontal and parietal lobe lesions

    Directory of Open Access Journals (Sweden)

    Himani Kashyap

    2011-04-01

    Full Text Available Visuospatial construction, traditionally viewed as a putative parietal function, also requires sustained attention, planning, organization strategies and error correction, and hence frontal lobe mediation. The relative contributions of the frontal and parietal lobes are poorly understood. To examine the contributions of parietal, frontal lobes, as well as right and left cerebral hemispheres to visuospatial construction. The Stick Construction Test for two-dimensional construction and the Block Construction Test for three-dimensional construction were administered pre-surgically to patients with lesions in the parietal lobe (n =9 and the frontal lobe (n=11, along with normal control subjects (n =20 matched to the patients on age (+/- 3 years, gender, education (+/- 3 years and handedness. The patients were significantly slower than the controls on both two-dimensional and three-dimensional tests. Patients with parietal lesions were slower than those with frontal lesions on the test of three-dimensional construction. Within each lobe patients with right and left sided lesions did not differ significantly. It appears that tests of three-dimensional construction might be most sensitive to visuospatial construction deficits. Visuospatial construction involves the mediation of both frontal and parietal lobes. The function does not appear to be lateralized. The networks arising from the parieto-occipital areas and projecting to the frontal cortices (e.g., occipito-frontal fasciculus may be the basis of the mediation of both lobes in visuospatial construction. The present findings need replication from studies with larger sample sizes.

  2. Self-Propagating Frontal Polymerization in Water at Ambient Pressure

    Science.gov (United States)

    Olten, Nesrin; Kraigsley, Alison; Ronney, Paul D.

    2003-01-01

    Advances in polymer chemistry have led to the development of monomers and initiation agents that enable propagating free-radical polymerization fronts to exist. These fronts are driven by the exothermicity of the polymerization reaction and the transport of heat from the polymerized product to the reactant monomer/solvent/initiator solution. The thermal energy transported to the reactant solution causes the initiator to decompose, yielding free radicals, which start the free radical polymerization process as discussed in recent reviews. The use of polymerization processes based on propagating fronts has numerous applications. Perhaps the most important of these is that it enables rapid curing of polymers without external heating since the polymerization process itself provides the high temperatures necessary to initiate and sustain polymerization. This process also enables more uniform curing of arbitrarily thick samples since it does not rely on heat transfer from an external source, which will necessarily cause the temperature history of the sample to vary with distance from the surface according to a diffusion-like process. Frontal polymerization also enables filling and sealing of structures having cavities of arbitrary shape without having to externally heat the structure. Water at atmospheric pressure is most convenient solvent to employ and the most important for practical applications (because of the cost and environmental issues associated with DMSO and other solvents). Nevertheless, to our knowledge, steady, self-propagating polymerization fronts have not been reported in water at atmospheric pressure. Currently, polymerization fronts require a high boiling point solvent (either water at high pressures or an alternative solvent such as dimethyl sulfoxide (DMSO) (boiling point 189 C at atmospheric pressure.) Early work on frontal polymerization, employed pressures up to 5000 atm in order to avoid boiling of the monomer/solvent/initiator solution. High

  3. Collisions engineering theory and applications

    CERN Document Server

    Frémond, Michel

    2017-01-01

    This book investigates collisions occurring in the motion of solids, in the motion of fluids but also in the motion of pedestrians in crowds. The duration of these presented collisions is short compared to the whole duration of the motion: they are assumed instantaneous. The innovative concept demonstrated in this book is that a system made of two solids, is deformable because their relative position changes. The definition of the velocities of deformation of the system introduced in the classical developments of mechanics, the principle of the virtual work and the laws of thermodynamics, allows a large range of applications such as crowd motions, debris flow motions, and shape memory alloys motions. The set of the applications is even larger: social sciences and mechanics are unified to predict the motion of crowds with application to transport management and to evacuation of theaters management.

  4. Collisions engineering. Theory and applications

    International Nuclear Information System (INIS)

    Fremond, Michel; Univ.

    2017-01-01

    This book investigates collisions occurring in the motion of solids, in the motion of fluids but also in the motion of pedestrians in crowds. The duration of these presented collisions is short compared to the whole duration of the motion: they are assumed instantaneous. The innovative concept demonstrated in this book is that a system made of two solids, is deformable because their relative position changes. The definition of the velocities of deformation of the system introduced in the classical developments of mechanics, the principle of the virtual work and the laws of thermodynamics, allows a large range of applications such as crowd motions, debris flow motions, and shape memory alloys motions. The set of the applications is even larger: social sciences and mechanics are unified to predict the motion of crowds with application to transport management and to evacuation of theaters management.

  5. Collisions engineering. Theory and applications

    Energy Technology Data Exchange (ETDEWEB)

    Fremond, Michel [Rome ' ' Tor Vergata' ' Univ. (Italy). Dept. of Civil Engineering and Computer Science

    2017-02-01

    This book investigates collisions occurring in the motion of solids, in the motion of fluids but also in the motion of pedestrians in crowds. The duration of these presented collisions is short compared to the whole duration of the motion: they are assumed instantaneous. The innovative concept demonstrated in this book is that a system made of two solids, is deformable because their relative position changes. The definition of the velocities of deformation of the system introduced in the classical developments of mechanics, the principle of the virtual work and the laws of thermodynamics, allows a large range of applications such as crowd motions, debris flow motions, and shape memory alloys motions. The set of the applications is even larger: social sciences and mechanics are unified to predict the motion of crowds with application to transport management and to evacuation of theaters management.

  6. Electron collisions in gas switches

    International Nuclear Information System (INIS)

    Christophorou, L.G.

    1989-01-01

    Many technologies rely on the conduction/insulation properties of gaseous matter for their successful operation. Many others (e.g., pulsed power technologies) rely on the rapid change (switching or modulation) of the properties of gaseous matter from an insulator to a conductor and vice versa. Studies of electron collision processes in gases aided the development of pulsed power gas switches, and in this paper we shall briefly illustrate the kind of knowledge on electron collision processes which is needed to optimize the performance of such switching devices. To this end, we shall refer to three types of gas switches: spark gap closing, self-sustained diffuse discharge closing, and externally-sustained diffuse discharge opening. 24 refs., 15 figs., 2 tabs

  7. Chirality in molecular collision dynamics

    Science.gov (United States)

    Lombardi, Andrea; Palazzetti, Federico

    2018-02-01

    Chirality is a phenomenon that permeates the natural world, with implications for atomic and molecular physics, for fundamental forces and for the mechanisms at the origin of the early evolution of life and biomolecular homochirality. The manifestations of chirality in chemistry and biochemistry are numerous, the striking ones being chiral recognition and asymmetric synthesis with important applications in molecular sciences and in industrial and pharmaceutical chemistry. Chiral discrimination phenomena, due to the existence of two enantiomeric forms, very well known in the case of interaction with light, but still nearly disregarded in molecular collision studies. Here we review some ideas and recent advances about the role of chirality in molecular collisions, designing and illustrating molecular beam experiments for the demonstration of chiral effects and suggesting a scenario for a stereo-directional origin of chiral selection.

  8. Electron collisions with ethylene oxide

    International Nuclear Information System (INIS)

    Freitas, T C; Bettega, M H F

    2009-01-01

    We present elastic cross sections for electron collisions with ethylene oxide. Our results compare well in shape with the experimental total cross section obtained by Szmytkowski et al.. We found a shape resonance at around 5 eV, which is in agreement with the observations of Allan and Andric and Szmytkowski et al.. Allan and Andric reported another low energy shape resonance which is not present in our results.

  9. Electron collisions with ethylene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, T C; Bettega, M H F, E-mail: tcf03@fisica.ufpr.b, E-mail: bettega@fisica.ufpr.b [Departamento de Fisica, Universidade Federal do Parana, CP 19044, 81531-990 Curitiba, Parana (Brazil)

    2009-11-01

    We present elastic cross sections for electron collisions with ethylene oxide. Our results compare well in shape with the experimental total cross section obtained by Szmytkowski et al.. We found a shape resonance at around 5 eV, which is in agreement with the observations of Allan and Andric and Szmytkowski et al.. Allan and Andric reported another low energy shape resonance which is not present in our results.

  10. Collision entropy and optimal uncertainty

    OpenAIRE

    Bosyk, G. M.; Portesi, M.; Plastino, A.

    2011-01-01

    We propose an alternative measure of quantum uncertainty for pairs of arbitrary observables in the 2-dimensional case, in terms of collision entropies. We derive the optimal lower bound for this entropic uncertainty relation, which results in an analytic function of the overlap of the corresponding eigenbases. Besides, we obtain the minimum uncertainty states. We compare our relation with other formulations of the uncertainty principle.

  11. In-Network Processing of an Iceberg Join Query in Wireless Sensor Networks Based on 2-Way Fragment Semijoins

    Directory of Open Access Journals (Sweden)

    Hyunchul Kang

    2015-03-01

    Full Text Available We investigate the in-network processing of an iceberg join query in wireless sensor networks (WSNs. An iceberg join is a special type of join where only those joined tuples whose cardinality exceeds a certain threshold (called iceberg threshold are qualified for the result. Processing such a join involves the value matching for the join predicate as well as the checking of the cardinality constraint for the iceberg threshold. In the previous scheme, the value matching is carried out as the main task for filtering non-joinable tuples while the iceberg threshold is treated as an additional constraint. We take an alternative approach, meeting the cardinality constraint first and matching values next. In this approach, with a logical fragmentation of the join operand relations on the aggregate counts of the joining attribute values, the optimal sequence of 2-way fragment semijoins is generated, where each fragment semijoin employs a Bloom filter as a synopsis of the joining attribute values. This sequence filters non-joinable tuples in an energy-efficient way in WSNs. Through implementation and a set of detailed experiments, we show that our alternative approach considerably outperforms the previous one.

  12. Frontal alpha asymmetry neurofeedback for the reduction of negative affect and anxiety.

    Science.gov (United States)

    Mennella, Rocco; Patron, Elisabetta; Palomba, Daniela

    2017-05-01

    Frontal alpha asymmetry has been proposed to underlie the balance between approach and withdrawal motivation associated to each individual's affective style. Neurofeedback of EEG frontal alpha asymmetry represents a promising tool to reduce negative affect, although its specific effects on left/right frontal activity and approach/withdrawal motivation are still unclear. The present study employed a neurofeedback training to increase frontal alpha asymmetry (right - left), in order to evaluate discrete changes in alpha power at left and right sites, as well as in positive and negative affect, anxiety and depression. Thirty-two right-handed females were randomly assigned to receive either the neurofeedback on frontal alpha asymmetry, or an active control training (N = 16 in each group). The asymmetry group showed an increase in alpha asymmetry driven by higher alpha at the right site (p neurofeedback for the reduction of negative affect and anxiety in clinical settings. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. A comparative study of linear measurements on facial skeleton with frontal and lateral cephalogram

    Directory of Open Access Journals (Sweden)

    Chandra Sekhar Gandikota

    2012-01-01

    Full Text Available Objective: To compare the accuracy of linear measurements on lateral and frontal cephalograms with gold standard skull measurements . Materials and Methods: Based on the specific criteria including reliable occlusion and condyles fitting in glenoid fossa, 15 dry human skulls were selected from a larger collection. Lateral and frontal cephalograms were taken of each skull by standardized methods. Steel ball bearings were used to identify the anatomic landmarks. Linear measurements in midsagittal plane were made on all three records. Intraclass correlation coefficients, Pearson′s correlation coefficient and regression constant were calculated to assess the records simultaneously. Results: The frontal cephalometric measurements showed high correlation to the direct skull measurements (Pearson′s coefficient 0.943frontal cephalometric images. The overall findings of the present study showed that the frontal cephalometric measurements are closely related to the direct skull measures.

  14. QCD studies in ep collisions

    Energy Technology Data Exchange (ETDEWEB)

    Smith, W.H. [Univ. of Wisconsin, Madison, WI (United States). Physics Dept.

    1997-06-01

    These lectures describe QCD physics studies over the period 1992--1996 from data taken with collisions of 27 GeV electrons and positrons with 820 GeV protons at the HERA collider at DESY by the two general-purpose detectors H1 and ZEUS. The focus of these lectures is on structure functions and jet production in deep inelastic scattering, photoproduction, and diffraction. The topics covered start with a general introduction to HERA and ep scattering. Structure functions are discussed. This includes the parton model, scaling violation, and the extraction of F{sub 2}, which is used to determine the gluon momentum distribution. Both low and high Q{sup 2} regimes are discussed. The low Q{sup 2} transition from perturbative QCD to soft hadronic physics is examined. Jet production in deep inelastic scattering to measure {alpha}{sub s}, and in photoproduction to study resolved and direct photoproduction, is also presented. This is followed by a discussion of diffraction that begins with a general introduction to diffraction in hadronic collisions and its relation to ep collisions, and moves on to deep inelastic scattering, where the structure of diffractive exchange is studied, and in photoproduction, where dijet production provides insights into the structure of the Pomeron. 95 refs., 39 figs.

  15. QCD studies in ep collisions

    International Nuclear Information System (INIS)

    Smith, W.H.

    1997-01-01

    These lectures describe QCD physics studies over the period 1992--1996 from data taken with collisions of 27 GeV electrons and positrons with 820 GeV protons at the HERA collider at DESY by the two general-purpose detectors H1 and ZEUS. The focus of these lectures is on structure functions and jet production in deep inelastic scattering, photoproduction, and diffraction. The topics covered start with a general introduction to HERA and ep scattering. Structure functions are discussed. This includes the parton model, scaling violation, and the extraction of F 2 , which is used to determine the gluon momentum distribution. Both low and high Q 2 regimes are discussed. The low Q 2 transition from perturbative QCD to soft hadronic physics is examined. Jet production in deep inelastic scattering to measure α s , and in photoproduction to study resolved and direct photoproduction, is also presented. This is followed by a discussion of diffraction that begins with a general introduction to diffraction in hadronic collisions and its relation to ep collisions, and moves on to deep inelastic scattering, where the structure of diffractive exchange is studied, and in photoproduction, where dijet production provides insights into the structure of the Pomeron. 95 refs., 39 figs

  16. Japanese and Korean Nursing Students' Motivation for Joining Disaster Relief Activities as Nurses in the Future.

    Science.gov (United States)

    Choe, Myoung-Ae; Kuwano, Noriko; Bang, Kyung-Sook; Cho, Mi-Kyoung; Yatsushiro, Rika; Kawata, Yuki

    The purpose of this study was to identify differences in motivation for joining disaster relief activities as a nurse in the future between Japanese and Korean nursing students. A descriptive 2-group comparative study design was used. The participants were 721 first- to fourth-year nursing students (Japanese, n = 324; Korean, n = 397). From June to September 2014, data were collected through a researcher-administered questionnaire and self-reported answers. The collected data were analyzed by descriptive statistics, the χ test, and the t test.No significant difference was found between Japanese and Korean students in motivation to join domestic relief activities should a disaster occur in the area in which they lived. Compared with Korean students, Japanese students strongly agreed that it is necessary to carry out relief work across borders when disasters occur in foreign countries (p = .001). Meanwhile, Japanese students showed less motivation than Korean students to join relief activities in other domestic areas and foreign countries (p = .020).The results of this study suggest that the motivation of Japanese students to join disaster relief activities as nurses in the future should a disaster occur in other domestic areas and foreign countries needs to be increased. The results also suggest that undergraduate students should be well prepared for disasters through disaster nursing education, including practical training, disaster drills, and simulation.

  17. Why Universities Join Cross-Sector Social Partnerships: Theory and Evidence

    Science.gov (United States)

    Siegel, David J.

    2010-01-01

    Cross-sector partnerships are an increasingly popular mode of organizing to address intractable social problems, yet theory and research have virtually ignored university involvement in such activity. This article attempts to ascertain the reasons universities join networks of other social actors to support a common cause. Theories on the…

  18. Joining and fabrication techniques for high temperature structures including the first wall in fusion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ho Jin; Lee, B. S.; Kim, K. B

    2003-09-01

    The materials for PFC's (Plasma Facing Components) in a fusion reactor are severely irradiated with fusion products in facing the high temperature plasma during the operation. The refractory materials can be maintained their excellent properties in severe operating condition by lowering surface temperature by bonding them to the high thermal conducting materials of heat sink. Hence, the joining and bonding techniques between dissimilar materials is considered to be important in case of the fusion reactor or nuclear reactor which is operated at high temperature. The first wall in the fusion reactor is heated to approximately 1000 .deg. C and irradiated severely by the plasma. In ITER, beryllium is expected as the primary armour candidate for the PFC's; other candidates including W, Mo, SiC, B4C, C/C and Si{sub 3}N{sub 4}. Since the heat affected zones in the PFC's processed by conventional welding are reported to have embrittlement and degradation in the sever operation condition, both brazing and diffusion bonding are being considered as prime candidates for the joining technique. In this report, both the materials including ceramics and the fabrication techniques including joining technique between dissimilar materials for PFC's are described. The described joining technique between the refractory materials and the dissimilar materials may be applicable for the fusion reactor and Generation-4 future nuclear reactor which are operated at high temperature and high irradiation.

  19. Convincing American Women to Join in the Efforts to Win World War I: A Lesson Plan.

    Science.gov (United States)

    Sunal, Cynthia S.; Haas, Mary E.

    1994-01-01

    Asserts that World War I, unlike previous wars, was not fought by small groups of professional soldiers, but with large groups of citizens, including women. Presents a lesson plan using poster and postcards that examines methods used by the U.S. government to rally women to join the war effort. (CFR)

  20. Increasing FSW join strength by optimizing feed rate, rotating speed and pin angle

    Science.gov (United States)

    Darmadi, Djarot B.; Purnowidodo, Anindito; Siswanto, Eko

    2017-10-01

    Principally the join in Friction Stir Welding (FSW) is formed due to mechanical bonding. At least there are two factors determines the quality of this join, first is the temperature in the area around the interface and secondly the intense of mixing forces in nugget zone to create the mechanical bonding. The adequate temperature creates good flowability of the nugget zone and an intensive mixing force produces homogeneous strong bonding. Based on those two factors in this research the effects of feed rate, rotating speed and pin angle of the FSW process to the tensile strength of resulted join are studied. The true experimental method was used. Feed rate was varied at 24, 42, 55 and 74 mm/minutes and from the experimental results, it can be concluded that the higher feed rate decreases the tensile strength of weld join and it is believed due to the lower heat embedded in the material. Inversely, the higher rotating speed increases the join’s tensile strength as a result of higher heat embedded in base metal and higher mixing force in the nugget zone. The rotating speed were 1842, 2257 and 2904 RPMs. The pin angle determines the direction of mixing force. With variation of pin angle: 0°, 4°, 8° and 12° the higher pin angle generally increases the tensile strength because of more intensive mixing force. For 12° pin angle the lower tensile strength is found since the force tends to push out the nugget area from the joint gap.