THE INFLUENCE OF BRAKE PADS THERMAL CONDUCTIVITY ON PASSANGER CAR BRAKE SYSTEM EFFICIENCY

Directory of Open Access Journals (Sweden)

Predrag D Milenković

2010-01-01

Full Text Available In phase of vehicle braking system designing, besides of mechanical characteristics, it is also necessary to take under consideration the system's thermal features. This is because it is not enough just to achieve proper braking power, for the brake system to be effective but equally important thing is the dissipation of heat to the environment. Heat developed in the friction surfaces dissipate into the environment over the disk in one hand and through the brake linings and caliper, in the other. The striving is to make that greatest amount of heat to dissipate not threw the brake pads but threw disc. The experimental researching of heat transfer process taking place at vehicle brakes was made in the R&D Center of "Zastava automobili" car factory in order to increase the efficiency of brake system. The standard laboratory and road test procedures were used, according to factory quality regulations. The modern equipment such as thermo camera, thermo couples, torque transducers, signal amplifiers, optical speed measuring system and laptop computer were used. In this paper will be shown the part of the experimental researching, which refers to the thermal conductivity of brake pad friction linings.

EVALUATION OF RESULTS OF ROAD RESEARCH OF LANOS CAR, EQUIPPED WITH AN ADVANCED HYDRAULIC BRAKE DRIVE

Directory of Open Access Journals (Sweden)

I. Nazarov

2016-12-01

Full Text Available The results of studies of road emergency braking of the car, the brake system equipped with an improved hydraulic brake actuator according to the patent number 76189 Ukraine are analyzed. This drive provides more efficient emergency braking of cars under operating conditions by of installing in each of the contours of the rear brakes one brake-power, each of which provides distribution of braking forces between the wheels of the corresponding side.

49 CFR 232.305 - Single car air brake tests.

Science.gov (United States)

2010-10-01

... from a train or when placed on a shop or repair track, as defined in § 232.303(a); (2) A car is on a shop or repair track, as defined in § 232.303(a), for any reason and has not received a single car air... 49 Transportation 4 2010-10-01 2010-10-01 false Single car air brake tests. 232.305 Section 232...

EXPERIMENTAL RESEARCH OF DYNAMIC QUALITIES OF FREIGHT CARS WITH BOGIES OF DIFFERENT DESIGNS

Directory of Open Access Journals (Sweden)

S. V. Myamlin

2014-04-01

Full Text Available Purpose. With the advent of new designs of freright cars the task of designing the more modern bogies, assessment of their dynamic properties depending on the type and structure of pecularities, accounting the axle loadings, providing the dynamic and running characteristics, meeting the conditions of impact on the track, stability, and frame forces intensity etc. becomes especially important. In order to launch the new production into manufacture and to assess the dynamic properties using different designs of bogies the running testes were conducted. They allowed one to compare the dynamic performance of the new bogie with the existing models. Methodology. The study was conducted using the method of numerical integration and mathematical modeling of dynamic loading of freight cars using the software package «Dynamics of Rail Vehicles» («DYNRAIL». Findings. The results of studies of dynamic characteristics of open cars with new and worn wheels of bogie models 18-9771, 18-9770 and 18-578 in graphical and tabular form are presented. All figures are within the normative values and do not exceed the maximum admissible ones. Originality. When designing the bogie for loading 23.5 t/axle almost all available technical solutions to improve the characteristics of the freight car bogies (elastic bearers, cassette bearing in axle boxes, axle boxe adapter of original design, bilinear central spring suspension, etc. were used. Practical value. As a result of the engineering works on projecting and manufacturing of the improved designs of freight car bogies a new design was received. It is highly competitive with the dynamic qualities of the best ones. Made choice of rational values of elastic-dissipative parameters of the bogie allows one to create standard series of running gears for freight cars for promising operating conditions.The results are of practical importance. They have found reflection in the number of author’spublications in special and

DETERMINATION OF FRICTION PERFORMANCE INFLUENCE IN THE SYSTEM "BODY–BOGIE" ON THE FREIGHT CAR DYNAMICS

Directory of Open Access Journals (Sweden)

S. V. Myamlin

2014-03-01

Full Text Available Purpose. The main requirements for the design of a new generation of cars, according to the Program of rolling stock renovation, are the requirements reducing the operating costs and increasing the cost-effectiveness of their use, taking into account the achievements of scientific and technical thought. Due to the urgency of this subject the paper is devoted to the study of the friction coefficient influence in the bearing connection «center plate – center bowl – bearers»of freight cars on their main dynamic parameters – coefficients of horizontal and vertical dynamics, body acceleration, frame strength, derailment stability factor. Methodology. The study was conducted by numerical integration and mathematical modeling of the freight car dynamic loading using the software package «Dynamics of Rail Vehicles» («DYNRAIL». Findings. Investigations have shown that the safety movement parameters are influenced by both the friction parameters in bearing connection «center plate – center bowl – bearers» of freight cars in empty and loaded state with bogies TSNII-X3 (model 18-100. Effect have other components of freight car dynamics, namely: radii of curved track sections, height of outer rail, etc. Originality. The author investigated the friction influence on the car dynamic loading using new approaches to solving the problem of predicting the rolling stock dynamics. Prediction was carried out on the basis of significantly updated theoretical material that covers all history of the friction theory and includes the results of recent experimental studies because of the speed on the straights and curves of small-and medium-range sections of the road.Practical value. The obtained results have practical orientation. During the research and after modeling with the improved method of accounting of friction processes dependencies of main dynamic parameters of a four-freight gondola on the value of the friction coefficient in the "body �

INVESTIGATION OF ANTILOCK BRAKE SYSTEM EFFECT ON PASSENGER CAR BRAFKING EFFICIENCY

Directory of Open Access Journals (Sweden)

I. Davidenko

2011-01-01

Full Text Available It has been experimentally proved that in case of emergency braking the constant decelera-tion of passenger cars equipped by antilock brake system exceeds the tabulated statistical data by 7,7–17 % that is recommended to apply at technical expertise at traffic accident causes investigation.

78 FR 44189 - Petition for Modification of Single Car Air Brake Test Procedures

Science.gov (United States)

2013-07-23

... brake pipe exhaust. Sec. 3.12.5: Added time and pressure criteria. Sec. 3.13: Added criteria for brake... brake pipes. Also, the choke in the 3/8- inch cock valve changed from 0.266 (17/64 ) to 0.313 (5/16 ), increasing the discharge rate to ensure emergency application on cars with long brake pipes. Sec. Sec. 2.2.4...

SOME ASPECTS OF THE DEFINITION OF EMPTY CARS STABILITY FROM SQUEEZING THEIR LONGITUDINAL FORCES IN THE FREIGHT TRAIN

Directory of Open Access Journals (Sweden)

A. O. Shvets

2015-06-01

Full Text Available Purpose. Despite of the implementation various programs to improve the safety of train traffic problem of reducing gatherings rolling stock off the rails is still relevant. The study aims to clarify the existing method of determining the factor of stability from the tire longitudinal forces to ensure the sustainability of cars with increasing speeds of the rolling stock. Methodology. Research was conducted by the method of mathematical modeling of loading freight car when driving at different speeds on straight and curved track sections. Findings. Analysis of the results shows that, for all selected freight cars for the calculation, the value of the safety factor by squeezing is smaller than the formulas of Standards. Corrections made to the formula for determining the safety factor by squeezing longitudinal forces, would achieve: 1 a higher safety factor of lightweight cars, excluding them squeezing longitudinal forces in the entire range of speeds of freight trains; 2 to develop and implement measures to prevent squeezing of cars in the entire range of motion; 3 to determine the degree of stability of the empty car in the head, middle and tail laden trains; 4 to offer optimal scheme of mixed trains formation. Originality. The analysis of existing methods for determining stability coefficient cars in freight trains from squeezing their longitudinal forces is presented in studies. Proposals are developed for the refinement of the design phase, construction and operation. Practical value. This study clarifies the existing method of determining the safety factor of stability from the squeezing longitudinal forces, as well as the influence on the magnitude of the coefficient of speed of movement of the rolling stock. Developed proposals for the refinement of existing methods for determining stability coefficient of longitudinal forces squeezing cars in a train, can reduce the number of retirements cars derailed by taking into account in the

NUMERICAL THERMAL ANALYSIS OF A CAR BRAKING SYSTEM

Directory of Open Access Journals (Sweden)

Patryk Różyło

2017-06-01

Full Text Available The study involved performing a numerical thermal analysis of selected components in a car braking system. The primary goal of the study was to determine the regions which are the most susceptible to variations in temperature, and to determine the degree of thermal impact upon them. The analysis was performed using the Abaqus environment. The examined components of the braking system were made of materials reflecting the mechanical properties of the real subassemblies. The FEM analysis enabled determination of the distribution of temperature in the system with respect to the properties of the investigated materials and applied boundary conditions.

Time headway in car following and operational performance during unexpected braking

NARCIS (Netherlands)

Brouwer, W.H.; van Winsum, W.

The relation between car-following behaviour and braking performance was studied in a driving simulator. The theoretical perspective was that individual differences in tactical car-driving behaviour may be related to skills on the operational level of the driving task via a process of adaptation. In

THE STUDY OF BRAKE SYSTEMS OF PASSENGER CARS MODEL 61-779 AND THEIR MODIFICATIONS PRODUCED BY OPEN JOINT STOCK COMPANY KRJUKIV CAR BUILDING PLANT

Directory of Open Access Journals (Sweden)

Yu. Ya. Vodiannikov

2007-11-01

Full Text Available The results of research of brake system for the model 61-779 of a passenger car manufactured by JSC «KVBZ» for the period from 2001 to 2006 are presented. It is shown that at the existing gear ratio of a brake lever transmission the passenger car brake efficiency does not correspond to running speed of 140 km/h. The causes of the wheel pairs damage occurrence in exploitation of a passenger train «Kiev – Moscow» as well as the recommendations on their elimination and brake system perfection are considered.

Benchmarking of regenerative braking for a fully electric car

NARCIS (Netherlands)

Varocky, B.J.; Nijmeijer, H.; Jansen, S.; Besselink, I.J.M.; Mansvelder, R.; Mansvelders, R.E.

2011-01-01

Short range of electric vehicles is one of the stumbling blocks in the way of electric cars to gaining wide user acceptance and becoming a major market player. The possibility to recover vehicle energy otherwise lost as heat during braking is an inherent advantage of a hybrid electric or a fully

Simulation of longitudinal dynamics of a freight train operating through a car dumper

Science.gov (United States)

Kovalev, R.; Sakalo, A.; Yazykov, V.; Shamdani, A.; Bowey, R.; Wakeling, C.

2016-06-01

A heavy haul train and car dumper model was created to analyse train longitudinal dynamics during dumping. Influence of such factors as performance curve of draft gears, total free slack in couplers, operating mode of train positioner and braking of last two cars of train on the in-train forces was considered.

A method to achieve comparable thermal states of car brakes during braking on the road and on a high-speed roll-stand

Science.gov (United States)

Wolff, Andrzej

2010-01-01

The temperature of a brake friction surface influences significantly the braking effectiveness. The paper describes a heat transfer process in car brakes. Using a developed program of finite element method, the temperature distributions in brake rotors (disc and drum brake) of a light truck have been calculated. As a preliminary consistency criterion of the brake thermal state in road and roll-stand braking conditions, a balance of the energy cumulated in the brake rotor has been taken into account. As the most reliable consistency criterion an equality of average temperatures of the friction surface has been assumed. The presented method allows to achieve on a roll-stand the analogical thermal states of automotive brakes, which are observed during braking in road conditions. Basing on this method, it is possible to calculate the braking time and force for a high-speed roll-stand. In contrast to the previous papers of the author, new calculation results have been presented.

Airborne Wear Particles Emissions fromCommercial Disc Brake Materials– Passenger Car Field Test

OpenAIRE

Wahlström, Jens; Olofsson, Ulf; Jansson, Anders; Olander, Lars

2008-01-01

Most modern passenger cars have disc brakes on the front wheels, which unlike drum brakes are not sealed off to the ambient air. During braking, there is wear to both the rotor and the pads. This wear process generates particles, which may become airborne. In field tests it is difficult to distinguish these particles from others in the surrounding environment. It may be preferable to use laboratory test stands where the cleanness of the surrounding air can be controlled. The validity of these...

Brake noise measurements on mixed freight trains with composite brake blocks

NARCIS (Netherlands)

Jansen, E.H.W.; Dittrich, M.G.; Sikma, E.L.

2008-01-01

Brake noise is known to be a major contributor to the total sound emission of railway yards and areas near stations. It has been established that composite brake blocks reduce rolling noise, but it is not known if this is also the case for braking noise. Therefore, in order to investigate this,

Fault diagnosis in hydraulic motor car brakes using model-based methods; Fehlerdiagnose von hydraulischen Kfz-Bremssystemen mit modellbasierten Methoden

Energy Technology Data Exchange (ETDEWEB)

Straky, H.; Boerner, M.; Isermann, R. [Technische Univ. Darmstadt (Germany). Inst. fuer Automatisierungstechnik

2002-07-01

The design and development of a model-supported monitoring and diagnosis sstem for motor car brakes is described. After a theoretical analysis of braking system dynamics, a model for calculating the brake liquid loss volume is established, and a model-supported monitoring system is developed on this basis. Early detection of small defects like leakages and air bubbles will make car brakes and motor car operation safer. [German] Am Beispiel der funktionellen Integration von analytischem Prozesswissen wurde in diesem Beitrag der Entwurf und die Entwicklung eines modellgestuetzten Ueberwachungs- und Diagnosesystems fuer Kfz-Bremssysteme beschrieben. Ueber die Analogie zwischen hydraulischen und elektrotechnischen Systemen mit konzentrierten Parametern, wurde eine theoretische Analyse der Bremssystemdynamik durchgefuehrt und ein Zustandsraummodell zur Bremsanlage erstellt, welches die Berechnung des im Fehlerfall entstehenden Bremsfluessigkeitsverlustvolumens ermoeglicht. Darauf aufbauend wurde ein modellgestuetztes Ueberwachungssystem entwickelt, welches durch eine fruehzeitige Erkennung kleiner Fehler wie Leckagen oder Luftblasen in Kfz-Bremssystemen einen wichtigen Beitrag zur Steigerung der Fahrsicherheit von Kraftfahrzeugen leisten kann. (orig.)

Brakes, brake control and driver assistance systems function, regulation and components

CERN Document Server

2014-01-01

Braking systems have been continuously developed and improved throughout the last years. Major milestones were the introduction of antilock braking system (ABS) and electronic stability program. This reference book provides a detailed description of braking components and how they interact in electronic braking systems. Contents Motor vehicle safety.- Basic principles of vehicle dynamics.- Car braking systems.- Car braking-system components.- Wheel brakes.- Antilock breaking systems.- Traction control system.- Electronic stability program.- Automatic brake functions.- Hydraulic modulator.- Sensors for brake control.- Sensotronic brake control.- Active steering.- Occupant protection systems.- Driver assistance systems.- Adaptive cruise control.- Parking systems.- Instrumentation.- Orientation methods.- Navigation systems.- Workshop technology. The target groups Motor-vehicle technicians in education and vocational training Master-mechanics and technicians in garage-workshops Teachers and lecturers in vocation...

Age and gender differences in time to collision at braking from the 100-Car Naturalistic Driving Study.

Science.gov (United States)

Montgomery, Jade; Kusano, Kristofer D; Gabler, Hampton C

2014-01-01

Forward collision warning (FCW) is an active safety system that aims to mitigate the effect of forward collisions by warning the driver of objects in front of the vehicle. Success of FCW relies on how drivers react to the alerts. Drivers who receive too many warnings that they deem as unnecessary-that is, nuisance alarms-may grow to distrust and turn the system off. To reduce the perception of nuisance alarms, FCW systems can be tailored to individual driving styles, but these driving styles must first be characterized. The objective of this study was to characterize differences in braking behavior between age and gender groups in car-following scenarios using data from the 100-Car Naturalistic Driving Study. The data source for this study was the 100-Car Naturalistic Driving Study, which recorded the driving of 108 primary drivers for approximately a year. Braking behavior was characterized in terms of time to collision (TTC) at brake application, a common metric used in the design of warning thresholds of FCW. Because of the large volume of data analyzed, the TTC at which drivers braked during car-following situations was collected via an automated search algorithm. The minimum TTC for each vehicle speed 10 mph increment from 10 mph to 80 mph was recorded for each driver. Mixed model analysis of variance was used to examine the differences between age and gender groups. In total, 527,861 brake applications contained in 11,503 trips were analyzed. Differences in TTC at braking were statistically significant for age and gender (Pbraking of 2.5±0.8 s, and females age 31-50 (n=6) had the highest average minimum TTC at braking of 6.4±0.9 s. On average, women (n=32) braked at a TTC 1.3 s higher than men (n=52). Age was a statistically significant factor for TTC at braking between participants under 30 (n=42) and participants over 30 (n=42), with the latter braking 1.7 s on average before the former. No statistical significance was found between ages 18-20 (n=15) and

A real-time visual inspection method of fastening bolts in freight car operation

Science.gov (United States)

Nan, Guo; Yao, JunEn

2015-10-01

A real-time inspection of the key components is necessary for ensuring safe operation of freight car. While traditional inspection depends on the trained human inspectors, which is time-consuming and lower efficient. With the development of machine vision, vision-based inspection methods get more railway on-spot applications. The cross rod end fastening bolts are important components on both sides of the train body that fixing locking plates together with the freight car main structure. In our experiment, we get the images containing fastening bolt components, and accurately locate the locking plate position using a linear Support Vector Machine (SVM) locating model trained with Histograms of Oriented Gradients (HOG) features. Then we extract the straight line segment using the Line Segment Detector (LSD) and encoding them in a range, which constitute a straight line segment dataset. Lastly we determine the locking plate's working state by the linear pattern. The experiment result shows that the localization accurate rate is over 99%, the fault detection rate is over 95%, and the module implementation time is 2f/s. The overall performance can completely meet the practical railway safety assurance application.

Population distributions of time to collision at brake application during car following from naturalistic driving data.

Science.gov (United States)

Kusano, Kristofer D; Chen, Rong; Montgomery, Jade; Gabler, Hampton C

2015-09-01

Forward collision warning (FCW) systems are designed to mitigate the effects of rear-end collisions. Driver acceptance of these systems is crucial to their success, as perceived "nuisance" alarms may cause drivers to disable the systems. In order to make customizable FCW thresholds, system designers need to quantify the variation in braking behavior in the driving population. The objective of this study was to quantify the time to collision (TTC) that drivers applied the brakes during car following scenarios from a large scale naturalistic driving study (NDS). Because of the large amount of data generated by NDS, an automated algorithm was developed to identify lead vehicles using radar data recorded as part of the study. Using the search algorithm, all trips from 64 drivers from the 100-Car NDS were analyzed. A comparison of the algorithm to 7135 brake applications where the presence of a lead vehicle was manually identified found that the algorithm agreed with the human review 90.6% of the time. This study examined 72,123 trips that resulted in 2.6 million brake applications. Population distributions of the minimum, 1st, and 10th percentiles were computed for each driver in speed ranges between 3 and 60 mph in 10 mph increments. As speed increased, so did the minimum TTC experience by drivers as well as variance in TTC. Younger drivers (18-30) had lower TTC at brake application compared to older drivers (30-51+), especially at speeds between 40 mph and 60 mph. This is one of the first studies to use large scale NDS data to quantify braking behavior during car following. The results of this study can be used to design and evaluate FCW systems and calibrate traffic simulation models. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

The Energy-Efficient Operation Problem of a Freight Train Considering Long-Distance Steep Downhill Sections

Directory of Open Access Journals (Sweden)

Xuan Lin

2017-06-01

Full Text Available With the energy consumption rising in rail transport, the railway sector is showing increasing interest in the energy-efficient operation of freight trains. Freight trains require more complicated driving strategies than ordinary passenger trains do due to their heavy loads, especially in the long-distance steep downhill (LDSD sections that are very common in freight rail lines in China. This paper studies the energy-efficient operation of a freight train considering LDSD sections. An optimal control model including regenerative and pneumatic braking is developed for the freight train. Then, when a train leaves/enters the LDSD section, we verify the uniqueness of control transitions and discuss the speed profile linkage between LDSD and its adjacent sections, which indicates that the periodic braking should be applied on LDSD sections for optimality. Additionally, given the same running time for the entire journey, our analysis shows that electrical braking-full braking strategy is more energy-efficient than coasting-full braking strategy on LDSD sections. Finally, a numerical algorithm for the optimal driving solution is proposed. The simulation results demonstrate that the driving strategies generated by the proposed algorithm performs better than those from fuzzy predictive control and field operation regarding energy saving.

Moisture measurements in iron ores, in freight cars, through nuclear techniques

International Nuclear Information System (INIS)

Castagnet, A.C.; Said, M.; Duarte, U.

1975-01-01

The possibility and the advantages of using a nuclear technique for measuring on the spot (in the freight cars) and the moisture content of iron ores are described. The measurements included the determination of the volumetric moisture content and the density. From this values, the moisture content in percentage by weight was calculated. Nuclear Chicago d/M Combination Density-Moisture Probe with a 5 mCi Ra/Be source, and a digital portable scaler, were used. The investigated techniques give good results when the measurements are made directly on the ore surface, and has economical advantages over the gravimetric method by sampling. The probable reasons for both, the aleatory scattering of points and the lack of linear correlation between the values of both methods, when the nuclear measurement is made across the car walls are analized

49 CFR 1242.73 - Cleaning car interiors and freight lost and damaged-all other (accounts XX-53-70 and 51-53-00).

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Cleaning car interiors and freight lost and damaged-all other (accounts XX-53-70 and 51-53-00). 1242.73 Section 1242.73 Transportation Other... freight lost and damaged—all other (accounts XX-53-70 and 51-53-00). Separate common expenses on basis of...

The effects of control-display gain on performance of race car drivers in an isometric braking task.

Science.gov (United States)

de Winter, J C F; de Groot, S

2012-12-01

To minimise lap times during car racing, it is important to build up brake forces rapidly and maintain precise control. We examined the effect of the amplification factor (gain) between brake pedal force and a visually represented output value on a driver's ability to track a target value. The test setup was a formula racing car cockpit fitted with an isometric brake pedal. Thirteen racing drivers performed tracking tasks with four control-display gains and two target functions: a step function (35 trials per gain) and a multisine function (15 trials per gain). The control-display gain had only minor effects on root mean-squared error between output value and target value, but it had large effects on build-up speed, overshoot, within-participants variability, and self-reported physical load. The results confirm the hypothesis that choosing an optimum gain involves balancing stability against physical effort.

Talking about the Automobile Braking System

Science.gov (United States)

Xu, Zhiqiang

2017-12-01

With the continuous progress of society, the continuous development of the times, people’s living standards continue to improve, people continue to improve the pursuit. With the rapid development of automobile manufacturing, the car will be all over the tens of thousands of households, the increase in car traffic, a direct result of the incidence of traffic accidents. Brake system is the guarantee of the safety of the car, its technical condition is good or bad, directly affect the operational safety and transportation efficiency, so the brake system is absolutely reliable. The requirements of the car on the braking system is to have a certain braking force to ensure reliable work in all cases, light and flexible operation. Normal braking should be good performance, in addition to a foot sensitive, the emergency brake four rounds can not be too long, not partial, not ring.

Distributed and self-adaptive vehicle speed estimation in the composite braking case for four-wheel drive hybrid electric car

Science.gov (United States)

Zhao, Z.-G.; Zhou, L.-J.; Zhang, J.-T.; Zhu, Q.; Hedrick, J.-K.

2017-05-01

Considering the controllability and observability of the braking torques of the hub motor, Integrated Starter Generator (ISG), and hydraulic brake for four-wheel drive (4WD) hybrid electric cars, a distributed and self-adaptive vehicle speed estimation algorithm for different braking situations has been proposed by fully utilising the Electronic Stability Program (ESP) sensor signals and multiple powersource signals. Firstly, the simulation platform of a 4WD hybrid electric car was established, which integrates an electronic-hydraulic composited braking system model and its control strategy, a nonlinear seven degrees-of-freedom vehicle dynamics model, and the Burckhardt tyre model. Secondly, combining the braking torque signals with the ESP signals, self-adaptive unscented Kalman sub-filter and main-filter adaptable to the observation noise were, respectively, designed. Thirdly, the fusion rules for the sub-filters and master filter were proposed herein, and the estimation results were compared with the simulated value of a real vehicle speed. Finally, based on the hardware in-the-loop platform and by picking up the regenerative motor torque signals and wheel cylinder pressure signals, the proposed speed estimation algorithm was tested under the case of moderate braking on the highly adhesive road, and the case of Antilock Braking System (ABS) action on the slippery road, as well as the case of ABS action on the icy road. Test results show that the presented vehicle speed estimation algorithm has not only a high precision but also a strong adaptability in the composite braking case.

ORGANIZATION OF FREIGHT TRANSPORTATION IN UKRAINE IN THE REFORMATION CONDTIONS

Directory of Open Access Journals (Sweden)

L. V. Martseniuk

2014-04-01

Full Text Available Purpose. Each country of the former Soviet Union carries out railroad industry reformation according to different models depending on orienting points and the goals it establishes. All railway administrations have faced the problem of considerable reduction of freight and passenger transportation volumes, aging of main assets, lack of investments for their renovation. The purpose of the paper is the development of optimal management structure of freight cars in conditions of railway transport reformation. Methodology. The theoretical and methodological basis for research is a systematic analysis of problems of providing the competitiveness of the transport industry in the field of freight railway transportations, theoretical principles of economics in the production efficiency, market economics transformation and management of the national economy. Findings. The author has developed an improved mechanism for freight traffic management, which differs from the existing one by its adaptation to the conditions of industry being reformed and the organization of management companies. These companies together with the Ukrainian transport and logistics center centralize management of all freight cars of both domestic and foreign operating companies. Originality. Author presents the theoretical generalization and new solution of the scientific problem. It appears in the development of theoretical and methodological approaches to the management structure of the freight cars by operating companies in conditions of railway transport reforming through the management companies organization in Ukraine. The above mentioned companies will combine two types of activity – the commercial one and the cars repair of different property, it will reduce car turnover, stay time of rolling stock in the inoperative park and thereby improve the efficiency of freight transportations. Particularly, they will lease and have the right to dispose universal cars of domestic

49 CFR 215.203 - Restricted cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Restricted cars. 215.203 Section 215.203..., DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Restricted Equipment § 215.203 Restricted cars. (a) This section restricts the operation of any railroad freight car that is— (1) More than 50...

49 CFR 215.121 - Defective car body.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective car body. 215.121 Section 215.121..., DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Car Bodies § 215.121 Defective car body. A railroad may not place or continue in service a car, if: (a) Any portion of...

Application of the Analytic Hierarchy Process to Identify the Most Suitable Lessor of Freight Car Finance Leasing

Directory of Open Access Journals (Sweden)

Lei Lei

2017-01-01

Full Text Available Finance leasing (also “equipment leasing” saves the cost, improves the efficiency and benefit, larger the manufacture supply channels, which is an optimal solution for equipment supply with uncertain freight demand. The article collects the definitions of Finance Leasing based on the four pillars theory of finance leasing, also divides the lessors in Freight Car finance leasing into three categories according to their major business: manufacturers, banks as the representative financial institutions, firms that specialized in finance leasing. To identify the most suitable lessor for each railway department, an indicator system is built and operated by Yaahp (a software based on Analytic Hierarchy Process.

49 CFR 232.609 - Handling of defective equipment with ECP brake systems.

Science.gov (United States)

2010-10-01

... (ECP) Braking Systems § 232.609 Handling of defective equipment with ECP brake systems. (a) Ninety-five... systems. 232.609 Section 232.609 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT...

Coupling System Design Optimization : A Survey and Assessment of Automatic Coupling Concepts for Rail Freight Cars : Volume 1. Executive Summary.

Science.gov (United States)

1978-05-01

The purpose of this study is to provide an independent identification, classification, and analysis of significant freight car coupling systems concepts offering potential for improved safety and operating costs over the present system. The basic met...

Coupling System Design Optimization : A Survey and Assessment of Automatic Coupling Concepts for Rail Freight Cars : Volume 2. Text and Appendices.

Science.gov (United States)

1978-05-01

The purpose of this study is to provide an independent identification, classification, and analysis of significant freight car coupling system concepts offering potential for improved safety and operating costs over the present system. The basic meth...

New approaches to enhancing efficiency of freight railway stations performance within industrial enterprises

Directory of Open Access Journals (Sweden)

Ваагн Емілійович Парунакян

2015-03-01

Full Text Available At present time freight stations operation is complicated by raised dynamics of production and transport processes. Under the given handling capacity, this circumstance affects duration of processing of inbound and internal flow of freight cars. In connection with the abovementioned, the article covers new approaches to the analysis and evaluation of operating characteristics, and designing of railway freight stations within industrial enterprises. These approaches base on the system adaptation of the railway freight stations structural layouts and parameters of technical facilities to new working conditions and production demands. As the criterion of optimization of freight station operation, the index of “transportation work” (freight car-hour was offered. It allows differentiating the elemental flows of freight cars from the overall flow of freight cars at the freight station. It also allows identifying structure, volumes and other parameters of train operation (duration of processing measured in freight car-hours, interpretational and technological idle time denoting the location and the reason for their occurrence. Moreover, the analysis and evaluation of yard operation is offered to be carried out via handling capacity balance, which illustrates the relation between the overall volume of transportation work and the amount of trains handled at the station. This allows establishing additional transportation work and makes it possible to evaluate the real (objective necessity in throughput and handling capacity of station facilities in particular, and the station in general. The operating characteristics that have been examined determine the new methodical approaches to designing of composition-and-structural layouts and parameters of industrial freight stations. As the basis for optimization of the station, the certain method of morphological analysis and synthesis of technical decisions can be accepted, with its modification due to the

Real life safety benefits of increasing brake deceleration in car-to-pedestrian accidents: Simulation of Vacuum Emergency Braking.

Science.gov (United States)

Jeppsson, Hanna; Östling, Martin; Lubbe, Nils

2018-02-01

The objective of this study is to predict the real-life benefits, namely the number of injuries avoided rather than the reduction in impact speed, offered by a Vacuum Emergency Brake (VEB) added to a pedestrian automated emergency braking (AEB) system. We achieve this through the virtual simulation of simplified mathematical models of a system which incorporates expected future advances in technology, such as a wide sensor field of view, and reductions in the time needed for detection, classification, and brake pressure build up. The German In-Depth Accident Study database and the related Pre Crash Matrix, both released in the beginning of 2016, were used for this study and resulted in a final sample of 526 collisions between passenger car fronts and pedestrians. Weight factors were calculated for both simulation model and injury risk curves to make the data representative of Germany as a whole. The accident data was used with a hypothetical AEB system in a simulation model, and injury risk was calculated from the new impact speed using injury risk curves to generate new situations using real accidents. Adding a VEB to a car with pedestrian AEB decreased pedestrian casualties by an additional 8-22%, depending on system setting and injury level, over the AEB-only system. The overall decrease in fatalities was 80-87%, an improvement of 8%. Collision avoidance was improved by 14-28%. VEB with a maximum deceleration in the middle of the modelled performance range has an effectiveness similar to that of an "early activation" system, where the AEB is triggered as early as 2 s before collision. VEB may therefore offer a substantial increase in performance without increasing false positive rates, which earlier AEB activation does. Most collisions and injuries can be avoided when AEB is supplemented by the high performance VEB; remaining cases are characterised by high pedestrian walking speed and late visibility due to view obstructions. VEB is effective in all analysed

DETERMINATION OF ENERGY LOSSES BY SHOCK ABSORBER IN A FREIGHT CAR AT CRASH MODE

Directory of Open Access Journals (Sweden)

Ya. V. Bolzhelarskyi

2016-08-01

Full Text Available Purpose. The purpose of this work is to determine the energy losses in the shock absorber of the freight car whose wheel-set moves in the derailed state on the track panel depending on the axle load and structural parameters of spring suspension. Methodology. On the basis of spring suspension construction analysis and operating principle of the friction shock absorber of the freight car bogie the authors provide the method for determining the energy absorbed by it. The calculations take the maximum values of the absorber elements displacement and the regulatory values of spring suspension parameters. Findings. The authors obtained the calculated formula for determining the energy absorbed by shock absorber for regulation-set mounting schemes of elastic bogie elements depending on the axial load. The mentioned curves are parabolic. Originality. The work examines the crash mode of the wheel-set movement on the track panels after its derailment. It is shown that the energy dissipation in the shock absorbers is the reason for increase in resistance to rolling stock movement. The formulas for calculating the amount of energy dissipated in the shock absorber with a maximum displacement of its elements are derived. This energy depends on the axle load and structural parameters of spring suspension. Practical value. The proposed method allows setting the value of the additional resistance to motion that occurs in crash mode which makes it possible to increase the accuracy of traction calculations.

Better Brakes

Science.gov (United States)

1976-01-01

Through continuing studies on high-temperature space materials useful for better brake linings, Bendix Corporation worked with Ames Research Center to develop a novel composite. This team worked to fabricate several combinations of composite materials and evaluated results. The one selected increases wear rates and lowers costs. It exhibits constant coefficient of friction at temperatures as high as 650 degrees Fahrenheit, a region where conventional brake linings fade markedly. Other suitable markets include brakes for trucks and industrial equipment such as overhead cranes and hoists. Afterwards brake linings could find successful application in passenger cars.

49 CFR 215.303 - Stenciling of restricted cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Stenciling of restricted cars. 215.303 Section 215... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Stenciling § 215.303 Stenciling of restricted cars. (a) Each restricted railroad freight car that is described in § 215.205(a) of...

DISTRIBUTED EXTERNAL SURFACE HARDENING OF CAR DESIGN BY WINDING

Directory of Open Access Journals (Sweden)

O. V. Fomin

2017-04-01

Full Text Available Purpose. The paper involves coverage of features and results of the research conducted by the authors to determine the feasibility and establishment of pre-stressed-strained state of freight cars by winding in order to improve their strength characteristics. It is also necessary to present the theoretical justification for the effectiveness of the application of this method for car designs and an appropriate example for the tank-car. Methodology. The conducted study is based on an analysis of known works on the subject, mathematical justification and computer modeling. At the calculations of rolling stock components contemporary conventional techniques were used. Findings. Authors found that the winding method for pre-stressed-strained state is effective and appropriate for use in the construction of railway rolling stock and, in particular freight cars. Freight car designs with the pre-stressed-strained state are characterized by a number of strength advantages, among which there is an improvement of the work on the perception of operational loads and resource conservation. Originality. For the first time it is proposed the improvement of bearing capacity of freight car constructions through the creation of its component in the directed stress-strained state. It is also for the first time proposed the use of distributed external surface hardening by the method of winding to create a pre-stress-strained state of structural components of freight cars. The methods for winding designs of freight cars and their implementation were considered. Practical value. The studies developed a number of technical solutions for improving the design of freight cars and tank-container, which has been patented. Corresponding solutions for the tank-car are partially presented. Practical implementation of such solutions will significantly improve the technical, economic and operational performances of car designs.

49 CFR 238.315 - Class IA brake test.

Science.gov (United States)

2010-10-01

... that utilize an electric signal to communicate a service brake application and only a pneumatic signal... and release of the brakes on the last car in the train; and (6) The communicating signal system is... be used to verify the set and release on cars so equipped. However, the observation of the brake...

30 CFR 75.1404 - Automatic brakes; speed reduction gear.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic brakes; speed reduction gear. 75.1404... Automatic brakes; speed reduction gear. [Statutory Provisions] Each locomotive and haulage car used in an... permit automatic brakes, locomotives and haulage cars shall be subject to speed reduction gear, or other...

DETERMINATION ALGORITHM OF OPTIMAL GEOMETRICAL PARAMETERS FOR COMPONENTS OF FREIGHT CARS ON THE BASIS OF GENERALIZED MATHEMATICAL MODELS

Directory of Open Access Journals (Sweden)

O. V. Fomin

2013-10-01

Full Text Available Purpose. Presentation of features and example of the use of the offered determination algorithm of optimum geometrical parameters for the components of freight cars on the basis of the generalized mathematical models, which is realized using computer. Methodology. The developed approach to search for optimal geometrical parameters can be described as the determination of optimal decision of the selected set of possible variants. Findings. The presented application example of the offered algorithm proved its operation capacity and efficiency of use. Originality. The determination procedure of optimal geometrical parameters for freight car components on the basis of the generalized mathematical models was formalized in the paper. Practical value. Practical introduction of the research results for universal open cars allows one to reduce container of their design and accordingly to increase the carrying capacity almost by100 kg with the improvement of strength characteristics. Taking into account the mass of their park this will provide a considerable economic effect when producing and operating. The offered approach is oriented to the distribution of the software packages (for example Microsoft Excel, which are used by technical services of the most enterprises, and does not require additional capital investments (acquisitions of the specialized programs and proper technical staff training. This proves the correctness of the research direction. The offered algorithm can be used for the solution of other optimization tasks on the basis of the generalized mathematical models.

Design of Mechanically Actuated Aerodynamic Braking System on a Formula Student Race Car

Science.gov (United States)

Muralidharan, Vivek; Balakrishnan, Abhijith; Vardhan, Vinit Ketan; Meena, Nikita; Kumar, Y. Suresh

2018-04-01

Every second in a racing competition counts the performance of a team against the other. Many innovative and sophisticated techniques are being employed to overcome loses in time and add to the performance of the vehicle. Especially in a car racing challenge there is more freedom to install these innovative systems to empower the car to maximum efficiency due to availability of more space. At the global spectrum there are few events which encourage such innovations. Formula Student Racing competitions are one of the global events organized by the Society of Automotive Engineers of different countries which gives opportunity to university students to build and race formula style cars. Like any other racing competitions in this high octane event having an inch over their opponents is always an advantage. Not just better acceleration and high velocities but also good deceleration is required to excel in the competition. Aerodynamic braking system is utilizing the aerodynamic drag force to create high deceleration. This mechanism can be installed on any car with spoilers with minimum modification. Being a student event great amount of care needs to be given to the safety concerns of the driver.

Driver braking behavior analysis to improve autonomous emergency braking systems in typical Chinese vehicle-bicycle conflicts.

Science.gov (United States)

Duan, Jingliang; Li, Renjie; Hou, Lian; Wang, Wenjun; Li, Guofa; Li, Shengbo Eben; Cheng, Bo; Gao, Hongbo

2017-11-01

Bicycling is one of the fundamental modes of transportation especially in developing countries. Because of the lack of effective protection for bicyclists, vehicle-bicycle (V-B) accident has become a primary contributor to traffic fatalities. Although AEB (Autonomous Emergency Braking) systems have been developed to avoid or mitigate collisions, they need to be further adapted in various conflict situations. This paper analyzes the driver's braking behavior in typical V-B conflicts of China to improve the performance of Bicyclist-AEB systems. Naturalistic driving data were collected, from which the top three scenarios of V-B accidents in China were extracted, including SCR (a bicycle crossing the road from right while a car is driving straight), SCL (a bicycle crossing the road from left while a car is driving straight) and SSR (a bicycle swerving in front of the car from right while a car is driving straight). For safety and data reliability, a driving simulator was employed to reconstruct these three scenarios and some 25 licensed drivers were recruited for braking behavior analysis. Results revealed that driver's braking behavior was significantly influenced by V-B conflict types. Pre-decelerating behaviors were found in SCL and SSR conflicts, whereas in SCR the subjects were less vigilant. The brake reaction time and brake severity in lateral V-B conflicts (SCR and SCL) was shorter and higher than that in longitudinal conflicts (SSR). The findings improve their applications in the Bicyclist-AEB and test protocol enactment to enhance the performance of Bicyclist-AEB systems in mixed traffic situations especially for developing countries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nonlinear Coupling Characteristics Analysis of Integrated System of Electromagnetic Brake and Frictional Brake of Car

Directory of Open Access Journals (Sweden)

Ren He

2015-01-01

Full Text Available Since theoretical guidance is lacking in the design and control of the integrated system of electromagnetic brake and frictional brake, this paper aims to solve this problem and explores the nonlinear coupling characteristics and dynamic characteristics of the integrated system of electromagnetic brake and frictional brake. This paper uses the power bond graph method to establish nonlinear coupling mathematical model of the integrated system of electromagnetic brake and frictional brake and conducts the contrastive analysis on the dynamic characteristics based on this mathematical model. Meanwhile, the accuracy of the nonlinear coupling mathematical model proposed above is verified on the hardware in the loop simulation platform, and nonlinear coupling characteristics of the integrated system are also analyzed through experiments.

IMPROVEMENT OF FREIGHT TRANSPORTATION PROCESS AND THEIR MANAGEMENT MECHANISM

Directory of Open Access Journals (Sweden)

L. V. Martsenyuk

2014-03-01

Full Text Available Purpose. For Ukraine as for a post-socialist state there is an objective need of reforming on railway transport. In order to meet the requirements of consumers both within the country and outside of it, it is necessary to solve transport problems in time and to introduce new technologies, without lagging behind the developed European states. The purpose of this article is identification of problems in the process of freight transportations and development of ways of their overcoming, formation of the principles of economic efficiency increase for the use of freight cars using the improvement of management mechanism of freight transportations in the conditions of reforming. Methodology. Methods of strategic planning, system approach for research on improvement of the management mechanism of freight transportations, as well as the organizational-administrative method for structure of management construction were used in this research. Findings. Authors have explored the problems arising in the process of transportation of goods and measures, which will increase the efficiency of goods transportation. Advanced mechanism of freight transportation management for its application in the conditions of the railway transport reforming was developed. It is based on management centralization. Originality. The major factors, which slow down process of cargo transportations, are investigated in the article. The principles of management mechanism improvement of freight transportations are stated. They are based on association of commercial and car-repair activity of depots. All this will allow reducing considerably a car turn by decrease in duration of idle times on railway transport, increasing the speed of freight delivery and cutting down a transport component in the price of delivered production. Practical value. The offered measures will improve the efficiency of rolling stock use and increase cargo volumes turnover, promote links of Ukraine with

DETERMINATION THE PERMISSIBLE FORCES IN ASSESSING THE LIFT RESISTANT FACTOR OF FREIGHT CARS IN TRAINS

Directory of Open Access Journals (Sweden)

A. O. Shvets

2016-02-01

Full Text Available Purpose. In the analytical research are considered: 1 relationships between the longitudinal force acting on the car in the train; 2 lateral and vertical forces of interaction in the contact zone «wheel – rail»; 3 dynamic indicators of cars with the magnitude of the car lift resistance factor; 4 obtaining of the dependencies between them. Methodology. The study was conducted by an analytical method assessing the sustainability of the freight car when driving at different speeds on the straight and curved track sections. Findings. In the process of studying the motion of the train, in the investigation of transport events, as well as during the training on the simulator operator, to assess the actions of the driver, the values of the longitudinal forces in the inter car connections are used. To calculate the longitudinal compressive forces, acting on the car, in which car lift resistance factor will be equal to the allowable value (critical force. To assess the impact on the value of the longitudinal force speed, coefficients of the vertical and horizontal dynamics, as well as the wind load on the side surface of the car body are the results of calculations of motion of the empty gondola car, model № 12-532 curve radius of 250 m with a rise of 150 mm and a transverse run of body of car frame relative to the track axis of the guide section 50 mm. Originality. In this study, the technique of determining the longitudinal compressive force was shown, that is somewhat different from the standard. So, as well as assessing the impact on it the speed of rolling coefficients of vertical and horizontal dynamics and wind load on the side surface of the car body. Practical value. The authors developed proposals on the enhancement of existing methods for determining the value of the longitudinal compressive forces acting on the car in which the safety value of the car lift resistance factor will be equal to the allowable value. It will evaluate the

49 CFR 238.317 - Class II brake test.

Science.gov (United States)

2010-10-01

....315(a)(1); (3) When previously tested units (i.e., cars that received a Class I brake test within the... hours) are added to the train; (4) When cars or equipment are removed from the train; and (5) When an... locomotives that utilize an electric signal to communicate a service brake application and only a pneumatic...

76 FR 50320 - Proposed Agency Information Collection Activities; Comment Request

Science.gov (United States)

2011-08-12

... and 10 minutes......... 83 Inspection and Repair of ECP records. Cars Before Release from Repair Shop... regulatory requirements related to power brakes on freight cars as well as the recently added requirements... Locomotives. 30,000 tests....... 15 minutes......... 7,500 232.3: Applicability--Cars Not 559 Railroads...

Estimate of potential benefit for Europe of fitting Autonomous Emergency Braking (AEB) systems for pedestrian protection to passenger cars.

Science.gov (United States)

Edwards, Mervyn; Nathanson, Andrew; Wisch, Marcus

2014-01-01

The objective of the current study was to estimate the benefit for Europe of fitting precrash braking systems to cars that detect pedestrians and autonomously brake the car to prevent or lower the speed of the impact with the pedestrian. The analysis was divided into 2 main parts: (1) Develop and apply methodology to estimate benefit for Great Britain and Germany; (2) scale Great Britain and German results to give an indicative estimate for Europe (EU27). The calculation methodology developed to estimate the benefit was based on 2 main steps: 1. Calculate the change in the impact speed distribution curve for pedestrian casualties hit by the fronts of cars assuming pedestrian autonomous emergency braking (AEB) system fitment. 2. From this, calculate the change in the number of fatally, seriously, and slightly injured casualties by using the relationship between risk of injury and the casualty impact speed distribution to sum the resulting risks for each individual casualty. The methodology was applied to Great Britain and German data for 3 types of pedestrian AEB systems representative of (1) currently available systems; (2) future systems with improved performance, which are expected to be available in the next 2-3 years; and (3) reference limit system, which has the best performance currently thought to be technically feasible. Nominal benefits estimated for Great Britain ranged from £119 million to £385 million annually and for Germany from €63 million to €216 million annually depending on the type of AEB system assumed fitted. Sensitivity calculations showed that the benefit estimated could vary from about half to twice the nominal estimate, depending on factors such as whether or not the system would function at night and the road friction assumed. Based on scaling of estimates made for Great Britain and Germany, the nominal benefit of implementing pedestrian AEB systems on all cars in Europe was estimated to range from about €1 billion per year for

Exposure to asbestos during brake maintenance of automotive vehicles by different methods.

Science.gov (United States)

Kauppinen, T; Korhonen, K

1987-05-01

Asbestos concentrations were measured during the different operations of brake maintenance of passenger cars, trucks and buses in 24 Finnish workplaces. The estimated average asbestos exposure during the workday (8-hr time-weighted average) was 0.1-0.2 fibers/cm3 during brake repair of trucks or buses, and under 0.05 f/cm3 during repair of passenger car brakes when the background concentration was not included in the calculations. The background concentration was estimated to be less than 0.1 f/cm3. During brake maintenance of buses and trucks, heavy exposure, 0.3-125 (mean 56) f/cm3, was observed during machine grinding of new brake linings if local exhaust was not in use. Other short-term operations during which the concentration exceeded 1 f/cm3 were the cleaning of brakes with a brush, wet cloth or compressed air jet. During brake servicing of passenger cars, the concentration of asbestos exceeded 1 f/cm3 only during compressed air blowing without local exhaust. The different methods of decreasing the exposure and the risk of asbestos-related diseases among car mechanics are discussed.

Improvement of Structure and Properties of Cast Ferrite-Pearlite Steels for Freight Railway Cars

Directory of Open Access Journals (Sweden)

A. Rabinovich

2008-03-01

Full Text Available As it i s known For increasing of propcnics (YTS 2 380 MPa of cast stcds i t is c f k ~ i v tco incrcasc conlcnt o f alhsti~uiionaal lloyingclcrncnts, (Si, Mn, Cr, Ni. 1 lowevcr it lcads to rising in pricc olstccl ton. lncrcasing of Si and Mn conrcnl only is limitcd hy decreasing o lductility and weld nhility. As a rule silicon contcnt at ~hcsca ccls is not highcr than 0.4-0.67'0 and Si:Mn ratio is not highcr khan 1:2. Nowfor grain rcfincmcnt ~wc sin oculation of stcct by nitrogcn and clcincnrs with high chcmical affinity to nltmgcn. Mostly vanadium i s usd.howcvcr niobium sornctime is uscd. Dissldvantagcs of this arc high cost of alloying clcmcnrs and low thcrrnodynamic stability OFvanadium and niobium nitridcs. Parlicles of V(C,N and Nh(C.N dissolvc during hcating fnr licnt trcatmcnt or during wclding. It [cads lodccrcasing of grain refinement elfcc!.Adaptat ion or this microalloying stratcgy Tor casts producing For rrcight mil way cars let cstirnatc possibility of application thcsc casts in ancw gcnerazion freight railway cars.

Experimental investigation of disc brakes for formula Bharat

Science.gov (United States)

Misra, Sheelam; Chandra, Sharad; Bagwadi, Ashutosh

2018-05-01

we have made the brake assembly for Formula Student India in which we gathered the information about the force distribution in Master Cylinder, Assembly of Master Cylinder, Disc Brakes, Pedal Assembly has been gathered from various sources in which we come to know about that Vertical Master Cylinder is much better than the Horizontal Master Cylinder because of which we are able to reduce the weight of the Formula Student Car which ultimately affects the performance of the car. In other words, we have considered the various environmental conditions in which this braking system. The dimensions for the Disc Brake rotor is considered according to the space constraints and the material is finalized according to the hunch of calculations and the environmental conditions.

Car Stopping Distance on a Tabletop

Science.gov (United States)

Haugland, Ole Anton

2013-01-01

Stopping distances in car braking can be an intriguing topic in physics teaching. It illustrates some basic principles of physics, and sheds valuable light on students' attitude towards aggressive driving. Due to safety considerations, it can be difficult to make experiments with actual car braking. (Contains 2 figures.)

Reducing braking distance by control of semi-active suspension

Energy Technology Data Exchange (ETDEWEB)

Niemz, T.

2007-07-01

This thesis presents a control algorithm for semi-active suspensions to reduce the braking distance of passenger cars. Active shock absorbers are controlled and used to influence the vertical dynamics during ABS-controlled full braking. The core of the approach presented in this paper is based on a switching control logic. The control algorithm is implemented in a compact class passenger car. Test drives on a real road, using a braking machine for reproducibility reasons, have been executed. It could be shown that it is possible to reduce the braking distance by affecting on the vertical dynamics of a passenger car in general. This is the first experimental result of this kind published ever. The amount of reduction depends on the height profile of the testing track chosen and on the initial velocity. On a road with an unevenness comparable to the one on a typical German Autobahn an average reduction of 1-2%, compared to the best passive damping, was achieved. (orig.)

ESTIMATION OF DRIVER’S POWER EXPENSES OF CAR BRAKE MANAGEMENT

Directory of Open Access Journals (Sweden)

A. Turenko

2010-01-01

Full Text Available The estimation method of driver’s power expenses for the brake management is offered. The estimation method takes into account power expenses at driving in action of the brake system and power expenses at holding the pressed brake pedal

The current state of the rail freight market in Russia: new forms of governance

Directory of Open Access Journals (Sweden)

Koncipko Natal'ja Vladimirovna

2015-10-01

Unsolved problems of the industry and the availability of infrastructure limited movements in the context of a sharp increase in the number of car Park led to the violation of a reasonable balance of rolling stock, the growth which outpaced the increase in transportation. This led to the reduction of hodnoty freight and has led to the simultaneous increase in the share of empty run freight car, and technological losses, including growth time of its turnover. The study showed that to improve the competitiveness of freight operators and increase their profits, you need to pass empty flights in centralized case management of JSC "RZD".

Pedestrian injury mitigation by autonomous braking.

Science.gov (United States)

Rosén, Erik; Källhammer, Jan-Erik; Eriksson, Dick; Nentwich, Matthias; Fredriksson, Rikard; Smith, Kip

2010-11-01

The objective of this study was to calculate the potential effectiveness of a pedestrian injury mitigation system that autonomously brakes the car prior to impact. The effectiveness was measured by the reduction of fatally and severely injured pedestrians. The database from the German In-Depth Accident Study (GIDAS) was queried for pedestrians hit by the front of cars from 1999 to 2007. Case by case information on vehicle and pedestrian velocities and trajectories were analysed to estimate the field of view needed for a vehicle-based sensor to detect the pedestrians one second prior to the crash. The pre-impact braking system was assumed to activate the brakes one second prior to crash and to provide a braking deceleration up to the limit of the road surface conditions, but never to exceed 0.6 g. New impact speeds were then calculated for pedestrians that would have been detected by the sensor. These calculations assumed that all pedestrians who were within a given field of view but not obstructed by surrounding objects would be detected. The changes in fatality and severe injury risks were quantified using risk curves derived by logistic regression of the accident data. Summing the risks for all pedestrians, relationships between mitigation effectiveness, sensor field of view, braking initiation time, and deceleration were established. The study documents that the effectiveness at reducing fatally (severely) injured pedestrians in frontal collisions with cars reached 40% (27%) at a field of view of 40 degrees. Increasing the field of view further led to only marginal improvements in effectiveness. 2010 Elsevier Ltd. All rights reserved.

Neutrons put the brakes on stress

International Nuclear Information System (INIS)

Gill, Katynna

2006-01-01

Don't you hate it when you're driving along, put your foot on the brake and feel that juddering feeling through the pedal? It happens when the disc brake rotors become distorted through normal use of the brakes. To the car manufacturing industry it's called r unout , and is a multimillion dollar warranty problem each year. Not to mention a pain for drivers! Dr Maurice Ripley and Dr Oliver Kirstein from the Australian Nuclear Science and Technology Organisation (ANSTO) wanted to figure out whether runout is caused by residual stresses from the manufacturing process or by normal use of the brake, so they decided to test and compare a used and new brake disc. 'To picture what metal looks like at the atomic level, imagine spheres stacked evenly around each other in all three dimensions,' explained Kirstein. T he spheres represent atoms in the metal and the structure is called a metallic lattice.' We're familiar with the idea that metal expands when it gets hot - the atoms get excited with the heat and have the energy to move further away from each other, so spaces between the atoms in the lattice get larger. 'When parts of the metal are heated up and cool down at different rates, you may end up with a distorted lattice with some parts expanded and others not,' explained Kirstein. 'This unevenness in the lattice creates residual stress.' While a bunch of methods were available to test the discs, Kirstein and Ripley picked neutrons from ANSTO's HIFAR (High Flux Australian Reactor) as their tool of choice. 'Neutrons allow us to look at the inside of the metal without damaging it,' said Kirstein. 'They can penetrate through the iron, so we were able to take measurements at a series of points at different depths through the brake disc.' Word around the car industry is that when residual stresses are relaxed through heating of the brake disc during use, the discs could potentially distort, causing the runout and that juddering feeling. But everyone was clueless as to what

Brake reactions of distracted drivers to pedestrian Forward Collision Warning systems.

Science.gov (United States)

Lubbe, Nils

2017-06-01

Forward Collision Warning (FCW) can be effective in directing driver attention towards a conflict and thereby aid in preventing or mitigating collisions. FCW systems aiming at pedestrian protection have been introduced onto the market, yet an assessment of their safety benefits depends on the accurate modeling of driver reactions when the system is activated. This study contributes by quantifying brake reaction time and brake behavior (deceleration levels and jerk) to compare the effectiveness of an audio-visual warning only, an added haptic brake pulse warning, and an added Head-Up Display in reducing the frequency of collisions with pedestrians. Further, this study provides a detailed data set suited for the design of assessment methods for car-to-pedestrian FCW systems. Brake response characteristics were measured for heavily distracted drivers who were subjected to a single FCW event in a high-fidelity driving simulator. The drivers maintained a self-regulated speed of 30km/h in an urban area, with gaze direction diverted from the forward roadway by a secondary task. Collision rates and brake reaction times differed significantly across FCW settings. Brake pulse warnings resulted in the lowest number of collisions and the shortest brake reaction times (mean 0.8s, SD 0.29s). Brake jerk and deceleration were independent of warning type. Ninety percent of drivers exceeded a maximum deceleration of 3.6m/s 2 and a jerk of 5.3m/s 3 . Brake pulse warning was the most effective FCW interface for preventing collisions. In addition, this study presents the data required for driver modeling for car-to-pedestrian FCW similar to Euro NCAP's 2015 car-to-car FCW assessment. Practical applications: Vehicle manufacturers should consider the introduction of brake pulse warnings to their FCW systems. Euro NCAP could introduce an assessment that quantifies the safety benefits of pedestrian FCW systems and thereby aid the proliferation of effective systems. Copyright © 2017

Usage of aids monitoring in automatic braking systems of modern cars

OpenAIRE

Dembitskyi V.; Mazylyuk P.; Sitovskyi O.

2016-01-01

Increased safety can be carried out at the expense the installation on vehicles of automatic braking systems, that monitor the traffic situation and the actions of the driver. In this paper considered the advantages and disadvantages of automatic braking systems, were analyzed modern tracking tools that are used in automatic braking systems. Based on the statistical data on accidents, are set the main dangers, that the automatic braking system will be reduced. In order to ensure the acc...

Investigation of a concept for electrohydraulic power supply for future passenger car brake systems considering; Untersuchung zur Konzeption einer elektrohydraulischen Energieversorgung fuer zukuenftige Pkw-Bremssysteme

Energy Technology Data Exchange (ETDEWEB)

Mutschler, R.

1999-07-01

An electrohydraulic power supply for passenger car brake systems is presented. These systems can be classified as brake by wire. The power supply consists of a hydropneumatic accumulator, a high pressure pump and an electric drive. The components are designed considering automotive requests. A new approach to minimize hydraulic pulsations caused by a high pressure piston pump is shown. [German] Eine elektrohydraulische Energieversorgung fuer PKW-Bremssysteme wird vorgestellt. Diese Systeme koennen mit brake by wire klassifiziert werden. Die Energieversorgung besteht aus einem hydropneumatischen Speicher, einer Hochdruckpumpe und einem elektrischen Antrieb. Die Komponenten werden hinsichtlich Automobilanforderungen ausgelegt. Eine neue Methode der Minimierung hydraulischer Pulsationen, die von einer Hochdruck Kolbenpumpe verursacht werden, wird gezeigt.

49 CFR 173.9 - Transport vehicles or freight containers containing lading which has been fumigated.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles or freight containers... MATERIALS REGULATIONS SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS General § 173.9 Transport... hazardous material. (b) No person may offer for transportation or transport a rail car, freight container...

Elemental composition of current automotive braking materials and derived air emission factors

Science.gov (United States)

Hulskotte, J. H. J.; Roskam, G. D.; Denier van der Gon, H. A. C.

2014-12-01

Wear-related PM emissions are an important constituent of total PM emissions from road transport. Due to ongoing (further) exhaust emission reduction wear emissions may become the dominant PM source from road transport in the near future. The chemical composition of the wear emissions is crucial information to assess the potential health relevance of these PM emissions. Here we provide an elemental composition profile of brake wear emissions as used in the Netherlands in 2012. In total, 65 spent brake pads and 15 brake discs were collected in car maintenance shops from in-use personal cars vehicles and analyzed with XRF for their metal composition (Fe, Cu, Zn, Sn, Al, Si, Zr, Ti, Sb, Cr, Mo, Mn, V, Ni, Bi, W, P, Pb and Co). Since car, engine and safety regulations are not nationally determined but controlled by European legislation the resulting profiles will be representative for the European personal car fleet. The brake pads contained Fe and Cu as the dominant metals but their ratio varied considerably, other relatively important metals were Sn, Zn and Sb. Overall a rather robust picture emerged with Fe, Cu, Zn and Sn together making up about 80-90% of the metals present in brake pads. Because the XRF did not give information on the contents of other material such as carbon, oxygen and sulphur, a representative selection of 9 brake pads was further analyzed by ICP-MS and a carbon and sulphur analyzer. The brake pads contained about 50% of non-metal material (26% C, 3% S and the remainder mostly oxygen and some magnesium). Based on our measurements, the average brake pad profile contained 20% Fe, 10% Cu, 4% Zn and 3% Sn as the dominant metals. The brake discs consisted almost entirely of metal with iron being the dominant metal (>95%) and only traces of other metals (<1% for individual metals). Non-metal components in the discs were 2-3% Silicon and, according to literature, ∼3% carbon. The robust ratio between Fe and Cu as found on kerbsides has been used to

Optimal design for slip deceleration control in anti-lock braking system

Science.gov (United States)

Mishra, Sheelam; Kumar, Pankaj; Rahman, Mohd. Saifur

2018-05-01

ABS (Anti-lock Braking System) is the most advanced braking system implemented in modern cars to avoid the slipping or skidding of the vehicle on the road. Moreover, it reduces the stopping distance of the vehicle because it avoids the locking of the wheel during braking. It enables the driver to steer the vehicle during braking. But every system has its downsides and likewise ABS too, it is not efficient during normal braking or snowy conditions. Our aim is to overcome these downsides and optimize Anti-lock Braking System to make it even better.

49 CFR 232.103 - General requirements for all train brake systems.

Science.gov (United States)

2010-10-01

... pneumatic technology, the integrity of the train line shall be monitored by the brake control system. (c) A... travel exceeds: (1) 10 1/2 inches for cars equipped with nominal 12-inch stroke brake cylinders; or (2) The piston travel limits indicated on the stencil, sticker, or badge plate for the brake cylinder with...

Computational Fluid Dynamics (CFD) investigation onto passenger car disk brake design

Science.gov (United States)

Munisamy, Kannan M.; Kanasan Moorthy, Shangkari K.

2013-06-01

The aim of this study is to investigate the flow and heat transfer in ventilated disc brakes using Computational Fluid Dynamics (CFD). NACA Series blade is designed for ventilated disc brake and the cooling characteristic is compared to the baseline design. The ventilated disc brakes are simulated using commercial CFD software FLUENTTM using simulation configuration that was obtained from experiment data. The NACA Series blade design shows improvements in Nusselt number compared to baseline design.

Computational Fluid Dynamics (CFD) investigation onto passenger car disk brake design

International Nuclear Information System (INIS)

Munisamy, Kannan M; Moorthy, Shangkari K Kanasan

2013-01-01

The aim of this study is to investigate the flow and heat transfer in ventilated disc brakes using Computational Fluid Dynamics (CFD). NACA Series blade is designed for ventilated disc brake and the cooling characteristic is compared to the baseline design. The ventilated disc brakes are simulated using commercial CFD software FLUENT TM using simulation configuration that was obtained from experiment data. The NACA Series blade design shows improvements in Nusselt number compared to baseline design.

Optimal design of an automotive magnetorheological brake considering geometric dimensions and zero-field friction heat

International Nuclear Information System (INIS)

Nguyen, Q H; Choi, S B

2010-01-01

This paper presents an optimal design of a magnetorheological (MR) brake for a middle-sized passenger car which can replace a conventional hydraulic disc-type brake. In the optimization, the required braking torque, the temperature due to zero-field friction of MR fluid, the mass of the brake system and all significant geometric dimensions are considered. After describing the configuration, the braking torque of the proposed MR brake is derived on the basis of the field-dependent Bingham and Herschel–Bulkley rheological model of the MR fluid. The optimal design of the MR brake is then analyzed taking into account available space, mass, braking torque and steady heat generated by zero-field friction torque of the MR brake. The optimization procedure based on the finite element analysis integrated with an optimization tool is proposed to obtain optimal geometric dimensions of the MR brake. Based on the proposed procedure, optimal solutions of single and multiple disc-type MR brakes featuring different types of MR fluid are achieved. From the results, the most effective MR brake for the middle-sized passenger car is identified and some discussions on the performance improvement of the optimized MR brake are described

Practical Use of the Braking Attributes Measurements Results

Directory of Open Access Journals (Sweden)

Ondruš Ján

2017-01-01

Full Text Available This contribution deals with issues of braking the passenger car. The measurement of braking deceleration of the vehicle Kia Cee´d 1,6 16 V was carried out by an optical device Correvit system. The measurement was carried out on the airport of the village of Rosina located close to Zilina. 10 drivers of different age, praxis, and kilometers driven participated in the measurement. The measured process was the vehicle full braking with the service brake of the initial speed of approximately 50 km.h-1. Each of the drivers had 10 attempts. In the closure of this contribution the results of the performed measurements, their evaluation and comparison are presented. Practical result from the contribution is mainly the measurement set of braking deceleration of the respective vehicle during intensive braking.

Influences of braking system faults on the vehicle dynamics

Energy Technology Data Exchange (ETDEWEB)

Straky, H.; Kochem, M.; Schmitt, J.; Hild, R.; Isermann, R. [Technische Univ., Darmstadt (Germany). Inst. of Automatic Control

2001-07-01

From a safety point of view the braking system is, besides the driver, one of the key subsystems in a car. The driver, as an adaptive control system, might not notice small faults in the hydraulic part of the braking system and sooner or later critical braking situations, e.g. due to a brake-circuit failure, may occur. Most of the drivers are not capable to deal with such critical situations. Therefore this paper investigates the influence of faults in the braking system on the dynamic vehicle behavior and the steering inputs of the driver to keep the vehicle on the desired course. (orig.)

Smart brake light system would provide more information to drivers

OpenAIRE

Trulove, Susan

2008-01-01

You are driving in heavy traffic. The brake lights on the car in front of you come on. Is the car slowing or is it going to stop? It slows to 25 mph and the lights go off. You drop back. The car in front of you stops suddenly! You stop just in time. The car behind you collects your rear bumper.

Advanced Emergency Braking Controller Design for Pedestrian Protection Oriented Automotive Collision Avoidance System

Directory of Open Access Journals (Sweden)

Guo Lie

2014-01-01

Full Text Available Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian.

Advanced emergency braking controller design for pedestrian protection oriented automotive collision avoidance system.

Science.gov (United States)

Lie, Guo; Zejian, Ren; Pingshu, Ge; Jing, Chang

2014-01-01

Automotive collision avoidance system, which aims to enhance the active safety of the vehicle, has become a hot research topic in recent years. However, most of the current systems ignore the active protection of pedestrian and other vulnerable groups in the transportation system. An advanced emergency braking control system is studied by taking into account the pedestrians and the vehicles. Three typical braking scenarios are defined and the safety situations are assessed by comparing the current distance between the host vehicle and the obstacle with the critical braking distance. To reflect the nonlinear time-varying characteristics and control effect of the longitudinal dynamics, the vehicle longitudinal dynamics model is established in CarSim. Then the braking controller with the structure of upper and lower layers is designed based on sliding mode control and the single neuron PID control when confronting deceleration or emergency braking conditions. Cosimulations utilizing CarSim and Simulink are finally carried out on a CarSim intelligent vehicle model to explore the effectiveness of the proposed controller. Results display that the designed controller has a good response in preventing colliding with the front vehicle or pedestrian.

The intelligent brake: SBS brakes safely and comfortably in all situations; Die intelligente Bremse: SBS verzoegert stets sicher und komfortabel

Energy Technology Data Exchange (ETDEWEB)

Anon.

1999-07-01

The Vision SLR study demonstrates the technology with which DaimlerChrysler vehicles will be equipped in the next century. The car that won the Gran Turismo incorporates the Sensortronic Brake System (SBS), an electrohydraulic braking system for optimum safety and comfort even in critical situations. [German] Die Fahrzeugstudie Vision SLR demonstriert eindrucksvoll die Technik, mit der DaimlerChrysler Fahrzeuge des kommenden Jahrhunderts ausstatten wird. Eine Besonderheit des Gran Turismo-Silberpfeils: das Sensortronic Brake System (SBS), ein elektrohydraulisches Bremssystem, das auch in kritischen Situationen optimale Fahrsicherheit und Komfort bietet. (orig.)

Operations Research for Freight Train Routing and Scheduling

DEFF Research Database (Denmark)

Harrod, Steven; Gorman, Michael F.

2011-01-01

This article describes the service design activities that plan and implement the rail freight operating plan. Elements of strategic service design include the setting of train frequency, the routing of cars among trains, and the consolidation of cars, called blocking. At the operational level......, trains are dispatched either according to train paths configured in advance, called timetables, or according to priority rules. We describe the North American and European practice along with selected modeling and problem solving methodologies appropriate for each of the operating conditions described...

Predict optimize the friction characteristics of brake pads; Brake pad no masatsu tokusei no yosoku to saitekika

Energy Technology Data Exchange (ETDEWEB)

Saotome, H [Nissin Kogyo Co., Tokyo (Japan); Kato, T [The University of Tokyo, Tokyo (Japan)

1997-10-01

The effect of the friction and the wear properties of brake pads were experimentally studied using a test rig of scale of 1/10 of the system used in a commercial car. The experimental data were investigated by the Multiple Regression Analysis and the Neural Network, and the effects of volume % of components on the friction and the wear properties were predicted. In addition the components of brake pads are optimized by Genetic Algorithms. 8 refs., 9 figs., 4 tabs.

Parametric Optimization Design of Brake Block Based on Reverse Engineering

Directory of Open Access Journals (Sweden)

Jin Hua-wei

2017-01-01

Full Text Available As one of the key part of automotive brake,the performance of brake block has a direct impact on the safety and comfort of cars. Modeling the brake block of disc brake in reverse parameterization by reverse engineering software, analyzing and optimizing the reconstructed model by CAE software. Processing the scanned point cloud by Geomagic Studio and reconstructing the CAD model of the brake block with the parametric surface function of the software, then analyzing and optimizing it by Wrokbench. The example shows that it is quick to reconstruct the CAD model of parts by using reverse parameterization method and reduce part re-design development cycle significantly.

Usage of aids monitoring in automatic braking systems of modern cars

Directory of Open Access Journals (Sweden)

Dembitskyi V.

2016-08-01

Full Text Available Increased safety can be carried out at the expense the installation on vehicles of automatic braking systems, that monitor the traffic situation and the actions of the driver. In this paper considered the advantages and disadvantages of automatic braking systems, were analyzed modern tracking tools that are used in automatic braking systems. Based on the statistical data on accidents, are set the main dangers, that the automatic braking system will be reduced. In order to ensure the accuracy of information conducted research for determination of optimal combination of different sensors that provide an adequate perception of road conditions. The tracking system should be equipped with a combination of sensors, which in the case of detection of an obstacle or dangers of signal is transmitted to the information processing system and decision making. Information from the monitoring system should include data for the identification of the object, its condition, the speed.

An Intelligent Regenerative Braking Strategy for Electric Vehicles

Directory of Open Access Journals (Sweden)

Zhibin Song

2011-09-01

Full Text Available Regenerative braking is an effective approach for electric vehicles (EVs to extend their driving range. A fuzzy-logic-based regenerative braking strategy (RBS integrated with series regenerative braking is developed in this paper to advance the level of energy-savings. From the viewpoint of securing car stability in braking operations, the braking force distribution between the front and rear wheels so as to accord with the ideal distribution curve are considered to prevent vehicles from experiencing wheel lock and slip phenomena during braking. Then, a fuzzy RBS using the driver’s braking force command, vehicle speed, battery SOC, battery temperature are designed to determine the distribution between friction braking force and regenerative braking force to improve the energy recuperation efficiency. The experimental results on an “LF620” prototype EV validated the feasibility and effectiveness of regenerative braking and showed that the proposed fuzzy RBS was endowed with good control performance. The maximum driving range of LF620 EV was improved by 25.7% compared with non-RBS conditions.

Development of a Cooperative Braking System for Front-Wheel Drive Electric Vehicles

Directory of Open Access Journals (Sweden)

Di Zhao

2018-02-01

Full Text Available Most electric vehicles adopt cooperative braking systems that can blend friction braking torque with regenerative braking torque to achieve higher energy efficiency while maintaining a certain braking performance and driving safety. This paper presented a new cooperative regenerative braking system that contained a fully-decoupled hydraulic braking mechanism based on a modified electric stability control system. The pressure control algorithm and brake force distribution strategy were also discussed. Dynamic models of a front wheel drive electric car equipped with this system and a simulation platform with a driver model and driving cycles were established. Tests to evaluate the braking performance and energy regeneration were simulated and analyzed on this platform and the simulation results showed the feasibility and effectiveness of this system.

49 CFR 38.175 - High-speed rail cars, monorails and systems.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false High-speed rail cars, monorails and systems. 38....175 High-speed rail cars, monorails and systems. (a) All cars for high-speed rail systems, including... monorail systems operating primarily on dedicated rail (i.e., not used by freight trains) or guideway, in...

CONTROLLING THE SPEED OF ROLLING CUTS IN CONDITIONS OF REDUCTION OF BRAKE POWER OF CAR RETARDERS

Directory of Open Access Journals (Sweden)

D. M. Kozachenko

2016-06-01

Full Text Available Purpose. The study aims to develop the requirements for organization of the marshalling process in the conditions when the power of retarder positions is less than the nominal one. Methodology. The research is carried out using the train traffic safety theory and mathematical modelling of hump processes. Findings. The current technical standard documents regulating the operational performance of humps do not contain direct instructions on how to proceed in the event of brake power loss by car retarders, thus creating threats to the traffic safety. This problem is quite acute for the Ukrainian railways in connection with a chronic shortage of funds for the repair and renewal of technical equipment, including the humps. At the same time, a significant drop in the volume of work leads to the fact that the hump required processing capacity can be provided in case of partial failure of retarders as well. Herewith the most important task is to ensure the breaking-up safety in conditions of parametric failures of retarders. The analysis of dangerous situations, the occurrence of which is possible at humps, as well as the modelling of cut rolling, allowed establishing the connection between the value of retarder tire pressing force on the car wheels and the breaking-up modes, providing the safety of marshalling process. The paper sets the application areas of such measures as the breaking-up speed reduction, breaking-up termination, the use of additional braking by block hangers. Originality. The originality of the work lies in the fact that it first obtained the complex of dependencies that determine the performance requirements for the power of hump retarders and allow the staff to enter the appropriate limits for breaking-up modes to ensure the marshalling process safety. Practical value. The results of the research can be used to supplement the «Instruction on the maintenance of facilities of mechanized and automated humps» in order to determine

49 CFR 215.9 - Movement of defective cars for repair.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movement of defective cars for repair. 215.9... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS General § 215.9 Movement of... (ii) The maximum speed and other restrictions necessary for safely conducting the movement; (2)(i) The...

Residual stresses in a cast iron automotive brake disc rotor

International Nuclear Information System (INIS)

Ripley, Maurice I.; Kirstein, Oliver

2006-01-01

Runout, and consequent juddering and pulsation through the brake pedal, is a multi-million dollar per year warranty problem for car manufacturers. There is some suspicion that the runout can be caused by relaxation of residual casting stresses when the disc is overheated during severe-braking episodes. We report here neutron-diffraction measurements of the levels and distribution of residual strains in a used cast iron brake disc rotor. The difficulties of measuring stresses in grey cast iron are outlined and three-dimensional residual-strain distributions are presented and their possible effects discussed

Dynamic analysis of three autoventilated disc brakes

Directory of Open Access Journals (Sweden)

Ricardo A. García-León

2017-09-01

Full Text Available The braking system of a car must meet several requirements, among which safety is the most important. It is also composed of a set of mechanical parts such as springs, different types of materials (Metallic and Non Metallic, gases and liquids. The brakes must work safely and predictably in all circumstances, which means having a stable level of friction, in any condition of temperature, humidity and salinity of the environment. For a correct design and operation of brake discs, it is necessary to consider different aspects, such as geometry, type of material, mechanical strength, maximum temperature, thermal deformation, cracking resistance, among others. Therefore, the main objective of this work is to analyze the dynamics and kinetics of the brake system from the pedal as the beginning of mathematical calculations to simulate the behavior and Analysis of Finite Elements (FEA, with the help of SolidWorks Simulation Software. The results show that the third brake disc works best in relation to the other two discs in their different working conditions such as speed and displacement in braking, concluding that depending on the geometry of the brake and the cooling channels these systems can be optimized that are of great importance for the automotive industry.

CoBra - a global tool for braking system development; CoBra - ein Tool fuer den globalen Einsatz in der Bremssystementwicklung

Energy Technology Data Exchange (ETDEWEB)

Sailer, U. [Robert Bosch GmbH, Stuttgart (Germany)

1999-07-01

When Robert Bosch GmbH took over the braking system activities of Allied Signal in 1996, they became able to develop complete braking systems for passenger cars. Braking systes for the different markets are now produced in three sites in Germany, France and the USA. Braking system development with its interfaces to component development and to car producers is a new development challenge, and the department K1 (ABS and braking systems) is cooperating with internal and external partners in developing a globally standardized program for design, simulation and analysis of passenger car braking systems. This contribution presents parts of the development project CoBra (Computation of Braking Systems). [German] Mit dem Kauf der Bremsenaktivitaeten der Firma Allied Signal im Jahre 1996 ist die Robert Bosch GmbH in der Lage, komplette Pkw-Bremssysteme zu entwickeln. Nunmehr werden an drei Entwicklungsstandorten in Deutschland, Frankreich und den USA Bremssysteme fuer die verschiedenen Maerkte entwickelt. Die Bremssystementwicklung, insbesondere die damit verbundenen Schnittstellen zu der Komponentenentwicklung und zum Automobilhersteller, stellt technisch und vom Entwicklungsprozess aus gesehen eine neue Herausforderung dar. Um ihr zu begegnen, wird im Geschaeftsbereich K1 (ABS and Braking Systems) derzeit in Zusammenarbeit mit internen und externen Partnern ein global einheitliches Programm zur Auslegung, Simulation und Analyse von Pkw-Bremssystemen entwickelt. Dieser Beitrag stellt Teile des Entwicklungsprojekts CoBra (Computation of Braking Systems) vor. (orig.)

The effect of a low-speed automatic brake system estimated from real life data.

Science.gov (United States)

Isaksson-Hellman, Irene; Lindman, Magdalena

2012-01-01

A substantial part of all traffic accidents involving passenger cars are rear-end collisions and most of them occur at low speed. Auto Brake is a feature that has been launched in several passenger car models during the last few years. City Safety is a technology designed to help the driver mitigate, and in certain situations avoid, rear-end collisions at low speed by automatically braking the vehicle.Studies have been presented that predict promising benefits from these kinds of systems, but few attempts have been made to show the actual effect of Auto Brake. In this study, the effect of City Safety, a standard feature on the Volvo XC60 model, is calculated based on insurance claims data from cars in real traffic crashes in Sweden. The estimated claim frequency of rear-end frontal collisions measured in claims per 1,000 insured vehicle years was 23% lower for the City Safety equipped XC60 model than for other Volvo models without the system.

Kinematics of child volunteers and child anthropomorphic test devices during emergency braking events in real car environment.

Science.gov (United States)

Stockman, Isabelle; Bohman, Katarina; Jakobsson, Lotta; Brolin, Karin

2013-01-01

The objective of this study was to present, compare, and discuss the kinematic response of children and child anthropomorphic test devices (ATDs) during emergency braking events in different restraint configurations in a passenger vehicle. A driving study was conducted on a closed-circuit test track comprising 16 children aged 4 to 12 years old and the Q3, Hybrid III (HIII) 3-year-old, 6-year-old, and 10-year-old ATDs restrained on the right rear seat of a modern passenger vehicle. The children were exposed to one braking event in each of the 2 restraint systems and the ATDs were exposed to 2 braking events in each restraint system. All events had a deceleration of 1.0 g. Short children (stature 107-123 cm) and the Q3, HIII 3-year-old, and 6-year-old were restrained on booster cushions as well as high-back booster seats. Tall children (stature 135-150 cm) and HIII 10-year-old were restrained on booster cushions or restrained by 3-point belts directly on the car seat. Vehicle data were collected and synchronized with video data. Forward trajectories for the forehead and external auditory canal (ear) were determined as well as head rotation and shoulder belt force. A total of 40 trials were analyzed. Child volunteers had greater maximum forward displacement of the head and greater head rotation compared to the ATDs. The average maximum displacement for children ranged from 165 to 210 mm and 155 to 195 mm for the forehead and ear target, respectively. Corresponding values for the ATDs were 55 to 165 mm and 50 to 160 mm. The change in head angle was greater for short children than for tall children. Shoulder belt force was within the same range for short children when restrained on booster cushions or high-back booster seats. For tall children, the shoulder belt force was greater when restrained on booster cushions compared to being restrained by seat belts directly on the car seat. The forward displacement was within the same range for all children regardless of

Does the brake response time of the right leg change after left total knee arthroplasty? A prospective study.

Science.gov (United States)

Marques, Carlos J; Barreiros, João; Cabri, Jan; Carita, Ana I; Friesecke, Christian; Loehr, Jochen F

2008-08-01

Patients undergoing total knee arthroplasty often ask when they can safely resume car driving. There is little evidence available on which physicians can rely when advising patients on this issue. In a prospective study we assessed the brake response time of 24 patients admitted to the clinic for left total knee arthroplasty preoperatively and then 10 days after surgery. On each measurement day the patients performed two tasks, a simple and a complex brake response time task in a car simulator. Ten days after left TKA the brake response time for the simple task had decreased by 3.6% (p=0.24), the reaction time by 3.1% (p=0.34) and the movement time by 6.6% (p=0.07). However, the performance improvement was not statistically significant. Task complexity increased brake response time at both time points. A 5.8% increase was significant (p=0.01) at 10 days after surgery. Based on our results, we suggest that patients who have undergone left total knee arthroplasty may resume car driving 10 days after surgery as long as they drive a car with automatic transmission.

ON OPERATION OF 740 M LONG FREIGHT TRAINS ON CZECH TEN-T RAILWAY NETWORK

Directory of Open Access Journals (Sweden)

Michal Drábek

2016-09-01

Full Text Available Regulation (EU No 1315/2013 defines actual scope of core and comprehensive TEN-T network, including both networks for railway freight transport. For the core network, possibility to operate 740 m long freight trains is required. The aim of this paper is to analyse availability of appropriate overtaking tracks for 740 m long freight trains. Due to ETCS braking curves and odometry, such trains, after ETCS implementation, will require 780-800 m long overtaking tracks. For practical reasons (e.g. bypass lines, whole Czech railway TEN-T network is analysed. The overtaking track, whose occupation means influence on scheduled traffic or threat to boarding passengers, are excluded. The data was collected from station schemes from Collection of Official Requisites for 2015/16 Timetable, issued by SŽDC, Czech state Infrastructure Manager. Most of appropriate tracks are over 800 m long, but their density in the network and in particular directions varies considerably. For freight traffic, gradient of the line is important, so in the resulting figure, there are marked significant peaks for particular lines as well. Czech TEN-T lines are further segmented on the basis of number of tracks and their traffic character. Then, specific issues on overtaking or crossing of 740 m long freight trains are discussed. As a conclusion, for long-term development of Czech TEN-T lines, targeted investment is recommended not only for passenger railway, but also for freight railway. An attractive capacity offer for railway undertakings, which can stimulate freight traffic on European Rail freight corridors, can be represented by network-bound periodic freight train paths with suitable long overtaking tracks outside bottlenecks. After the overtaking by passenger trains, a freight train should run without stop through large node station or a bottleneck area. Before the sections with high gradients, coupling of additional locomotives should be connected with the overtaking

Reconstruction of braking force in vehicles with electromechanically actuated wheel brakes; Rekonstruktion der Bremskraft bei Fahrzeugen mit elektromechanisch betaetigten Radbremsen

Energy Technology Data Exchange (ETDEWEB)

Schwarz, R.

1999-07-01

Modern braking systems have a variety of functions, but implementation of the enhanced functionality with conventional hydraulic systems is difficult because of electronic actuation. The car industry therefore is working on new braking systems in which the braking force is generated individually on the wheels by means of electromechanical actuators. Owing to their nonlinear characteristics and variable braking efficiency, electromechanically actuated wheel brakes must be operated in a closed control loop. The author presents a low-cost method for reconstruction of the braking force which is required for efficient control. [German] Aufgrund des gestiegenen Sicherheits- und Komfortbewusstseins der Fahrzeugkaeufer ist die Funktionsvielfalt moderner Bremssysteme in den letzten Jahren staendig gewachsen. Die Umsetzung der erweiterten Funktionalitaet mittels konventioneller Bremsenhydraulik ist jedoch durch den elektronischen Eingriff sehr aufwendig. - Von der Automobilzulieferindustrie werden daher neuartige Bremssysteme entwickelt, bei denen die Bremskraft an den einzelnen Raedern von elektromechanischen Bremsaktuatoren aufgebracht wird. - Elektromechanisch betaetigte Radbremsen muessen aufgrund ihres nichtlinearen Verhaltens und des veraenderlichen Wirkungsgrades im geschlossenen Regelkreis betrieben werden. In dieser Arbeit wird erstmals ein Verfahren vorgestellt, mit dem die fuer die Regelung benoetigte Rueckfuehrungsgroesse Bremskraft kostenguenstig rekonstruiert werden kann. (orig.)

Effect of hip braces on brake response time: Repeated measures designed study.

Science.gov (United States)

Dammerer, Dietmar; Waidmann, Cornelia; Huber, Dennis G; Krismer, Martin; Haid, Christian; Liebensteiner, Michael C

2017-08-01

The question whether or not a patient with a hip brace should drive a car is of obvious importance because the advice given to patients to resume driving is often anecdotal as few scientific data are available on this specific subject. To assess driving ability (brake response time) with commonly used hip braces. Repeated measures design. Brake response time was assessed under six conditions: (1) without a brace (control), (2) with a typical postoperative hip brace with adjustable range of motion and the settings: unrestricted, (3) flexion limited to 70°, (4) extension blocked at 20° hip flexion, (5) both flexion and extension limited (20°/70°) and (6) an elastic hip bandage. Brake response time was assessed using a custom-made driving simulator as used in previous studies. The participants were a convenience sample of able-bodied participants. A total of 70 participants (35 women and 35 men) participated in our study. Mean age was 31.1 (standard deviation: 10.6; range: 21.7-66.4) years. A significant within-subject effect for brake response time was found ( p = 0.009), but subsequent post hoc analyses revealed no significant differences between control and the other settings. Based on our findings, it does not seem mandatory to recommend driving abstinence for patients wearing a hip orthosis. We suggest that our results be interpreted with caution, because (1) an underlying pathological hip condition needs to be considered, (2) the ability to drive a car safely is multifactorial and brake response time is only one component thereof and (3) brake response time measurements were performed only with healthy participants. Clinical relevance Hip braces are used in the context of joint-preserving and prosthetic surgery of the hip. Therefore, clinicians are confronted with the question whether to allow driving a car with the respective hip brace or not. Our data suggest that hip braces do not impair brake response time.

Metaphoric Car Drawings By a 12-Year-Old Congenitally Blind Girl.

Science.gov (United States)

Chao, Hsin-Yi; Kennedy, John M

2015-12-01

A 12-year-old congenitally-blind girl drew a car moving, stationary, and braking. For stationary, she put the wheels inside the car and, for braking, drew the wheels as rough rectangles. At the age verbal metaphor is understood (Winner, 1988), the girl invented metaphoric drawings. In these, what is shown is not what is meant. In late childhood, metaphor may be understood similarly in pictures and words and by the sighted and blind. © The Author(s) 2015.

Applicability analysis of hexahedral hollow profiles as component elements of supporting systems for gondola cars

Directory of Open Access Journals (Sweden)

O. V. Fomin

2014-12-01

Full Text Available Purpose. The purpose of work is presentation of features and results of the conducted works on determination of introduction expedience of hexahedral hollow profiles as the component elements of the modern supporting systems of railway freight gondola cars. Methodology. During the research an introduction methodology of different types of profiles as alternative to the existent supporting elements of the body module for freight car was used. This methodology had been developed by the author before. It is oriented to the reduction in material consumption and providing of strength requirements and operating reliability of the car design under study. The developed methodology includes the procedures of admissible values calculation of the resistance moments of the section of the hexahedral hollow profile, which is being introduced. It also includes the determination of optimum (i.e. characterized by the minimum material consumption when meeting the durability requirements values of height and minimum thickness of profile in the conditions of construction limitations. At the same time the admissible resistance moments are calculated as such, which are equal to the value of existent implementation of supporting element or as such that are determined taking into account the surplus design reserve. The first direction is applied in this work. Findings. As a result of the conducted research the introduction expedience of hexahedral hollow profiles as vertical rods of the lateral and latitude belts of the walls of the butt-end freight gondola cars is grounded and the optimum parameters of such replacements are determined. Originality. The problem of the use expedience of hexahedral hollow profiles as the supporting elements of the freight gondola cars bodies was first considered in the article. To solve this problem the mathematical models describing the dependence of basic strength and mass indexes of the proper profiles on varying the geometrical

Could Expanded Freight Rail Reduce Air Pollution from Trucks?

Science.gov (United States)

Bickford, E. E.; Holloway, T.; Johnston, M.

2010-12-01

Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

Toxicity and mutagenicity of low-metallic automotive brake pad materials.

Science.gov (United States)

Malachova, Katerina; Kukutschova, Jana; Rybkova, Zuzana; Sezimova, Hana; Placha, Daniela; Cabanova, Kristina; Filip, Peter

2016-09-01

Organic friction materials are standardly used in brakes of small planes, railroad vehicles, trucks and passenger cars. The growing transportation sector requires a better understanding of the negative impact related to the release of potentially hazardous materials into the environment. This includes brakes which can release enormous quantities of wear particulates. This paper addresses in vitro detection of toxic and mutagenic potency of one model and two commercially available low-metallic automotive brake pads used in passenger cars sold in the EU market. The model pad made in the laboratory was also subjected to a standardized brake dynamometer test and the generated non-airborne wear particles were also investigated. Qualitative "organic composition" was determined by GC/MS screening of dichloromethane extracts. Acute toxicity and mutagenicity of four investigated sample types were assessed in vitro by bioluminescence assay using marine bacteria Vibrio fischeri and by two bacterial bioassays i) Ames test on Salmonella typhimurium His(-) and ii) SOS Chromotest using Escherichia coli PQ37 strain. Screening of organic composition revealed a high variety of organic compounds present in the initial brake pads and also in the generated non-airborne wear debris. Several detected compounds are classified by IARC as possibly carcinogenic to humans, e. g. benzene derivatives. Acute toxicity bioassay revealed a response of bacterial cells after exposure to all samples used. Phenolic resin and wear debris were found to be acutely toxic; however in term of mutagenicity the response was negative. All non-friction exposed brake pad samples (a model pad and two commercial pad samples) were mutagenic with metabolic activation in vitro. Copyright © 2016 Elsevier Inc. All rights reserved.

Comparisonal Analysis of Manuevering and Braking

Directory of Open Access Journals (Sweden)

Artūras Žukas

2011-04-01

Full Text Available This article covers the possibility of avoiding a traffic accident considering a car driver who is fallen in a dangerous situation. In such a case, the driver can choose one of the following ways: hard braking or one of the types of maneuvering, including turning off, turning with straightening or changing a line regarding road surface type (dry asphalt, wet asphalt or snowy asphalt. The article also proposes formulas for calculating road distance the car travels till dead stop. Moreover, the tables display theoretical values taking into account various car speeds and road surfaces. The pictures help with determining the most suitable type of action in light of road and weather conditions as well as car speed. The pictures clearly show the dependence of road length on movement speed. At the end of the article, conclusions are proposed.Article in Lithuanian

Modelling freight transport

NARCIS (Netherlands)

Tavasszy, L.A.; Jong, G. de

2014-01-01

Freight Transport Modelling is a unique new reference book that provides insight into the state-of-the-art of freight modelling. Focusing on models used to support public transport policy analysis, Freight Transport Modelling systematically introduces the latest freight transport modelling

Static load simulation of steering knuckle for a formula student race car

Science.gov (United States)

Saputro, Bagus Aulia; Ubaidillah, Triono, Dicky Agus; Pratama, Dzaky Roja; Cahyono, Sukmaji Indro; Imaduddin, Fitrian

2018-02-01

This research aims to determine the stress distribution which occurs on the steering knuckle and to define its safety factor number. Steering knuckle is the most critical part of a car's steering system. Steering knuckle supports the tie rod, brake caliper, and the wheels to provide stability. Steering knuckle withstands the load which given on the front wheels and functions as the wheel's axis. Balljoint and king support the rotation of the suspension arm. When the car is in idle position, knuckle hold the weight of the car, it gets braking force when it's braking and cornering. Knuckle is designed to have the strength that could withstand load and to have a good safety factor value. Knuckle is designed using Fusion software then simulated using Fusion simulation software with a static load, moment braking force, and cornering force as the loads in this simulation. The simulation works in ideal condition. The result of this simulation is satisfying. This simulation produces a maximum displacement of 0.01281mm, the maximum shear stress is 3.707 MPa on the stub hole, and the safety factor is 5.24. The material used for this product is mild steel AISI 1018.

The contribution to the greenhouse effect by passenger cars and heating is increasing

International Nuclear Information System (INIS)

Bouchereau, J.M.

2000-12-01

Between 1990 and 1998, the domestic sector contribution to the greenhouse effect increased from 25 % to 27 %. During this period, there was a 20 % rise in greenhouse gas emissions from passenger cars. These emissions amounted to 20 million tonnes of carbon equivalent out of a total of 175 million tonnes in 1998 (all sectors taken together). Carbon dioxide emissions from the tertiary sector increased by 2,3 % annually between 1980 and 1998, particularly as a result of increased road freight transport. Although technological progress has been made on fuel consumption of vehicles, greater use of passenger cars combined with decreasing running costs has led to gross emissions in France being 2 % more in 1998 than in 1990. In 1998, the transport sector (passenger cars and freight transport) was responsible for three-quarters of this increase. (author)

Stabilization of car-caravan combination using independent steer and drive/or brake forces distribution

Directory of Open Access Journals (Sweden)

Ossama Mokhiamar

2015-09-01

Full Text Available Once a combined vehicle becomes unstable, it is very difficult for a driver to stabilize it especially under severe driving conditions, such as turning with braking. This is mainly due to the effect of the towed vehicle on the towing vehicle through the hitch jackknifing. This effect makes the handling characteristics of a car-caravan combination different from those of a single vehicle. Therefore, this paper proposes a control design concept for an optimum distribution of longitudinal and lateral forces of the four tires of a towing vehicle. The mean objectives of the control system were to stabilize the motion of an articulated vehicle utilizing the tires entire ability in both longitudinal and lateral directions as well as to make the handling characteristics of an articulated vehicle similar to those of a single one. The sliding control law based on vehicle planar equations of motion is used to derive the control laws. The proposed control system is evaluated under severe driving conditions and compared with the results of integrated control systems. The robustness of the articulated vehicle motion with the proposed control against the coefficient of friction variation is discussed.

Analysis of the stability of PTW riders in autonomous braking scenarios.

Science.gov (United States)

Symeonidis, Ioannis; Kavadarli, Gueven; Erich, Schuller; Graw, Matthias; Peldschus, Steffen

2012-11-01

While fatalities of car occupants in the EU decreased remarkably over the last decade, Powered Two Wheelers (PTWs) fatalities still increase following the increase of PTW ownership. Autonomous braking systems have been implemented in several types of vehicles and are presently addressed by research in the field of PTWs. A major concern in this context is the rider stability. Experiments with volunteers were performed in order to find out whether autonomous braking for PTWs will produce a greater instability of the rider in comparison to manual braking. The PTW's braking conditions were simulated in a laboratory with a motorcycle mock-up mounted on a sled, which was accelerated with an average of 0.35 g. The motion of the rider was captured in autonomous braking scenarios with and without pre-warning as well as in manual braking scenarios. No significant differences between the scenarios were found with respect to maximum forward displacement of the volunteer's torso and head (pautonomous braking at low deceleration will not cause significant instabilities of the rider in comparison to manual braking in idealized laboratory conditions. Based on this, further research into the development and implementation of autonomous braking systems for PTWs, e.g. by extensive riding tests, seems valuable. Copyright © 2011 Elsevier Ltd. All rights reserved.

Evaluation of the crash mitigation effect of low-speed automated emergency braking systems based on insurance claims data.

Science.gov (United States)

Isaksson-Hellman, Irene; Lindman, Magdalena

2016-09-01

The aim of the present study was to evaluate the crash mitigation performance of low-speed automated emergency braking collision avoidance technologies by examining crash rates, car damage, and personal injuries. Insurance claims data were used to identify rear-end frontal collisions, the specific situations where the low-speed automated emergency braking system intervenes. We compared cars of the same model (Volvo V70) with and without the low-speed automated emergency braking system (AEB and no AEB, respectively). Distributions of spare parts required for car repair were analyzed to identify car damage, and crash severity was estimated by comparing the results with laboratory crash tests. Repair costs and occupant injuries were investigated for both the striking and the struck vehicle. Rear-end frontal collisions were reduced by 27% for cars with low-speed AEB compared to cars without the system. Those of low severity were reduced by 37%, though more severe crashes were not reduced. Accordingly, the number of injured occupants in vehicles struck by low-speed AEB cars was reduced in low-severity crashes. In offset crash configurations, the system was found to be less effective. This study adds important information about the safety performance of collision avoidance technologies, beyond the number of crashes avoided. By combining insurance claims data and information from spare parts used, the study demonstrates a mitigating effect of low-speed AEB in real-world traffic.

Driver Behavioral Changes through Interactions with an Automatic Brake System for Collision Avoidance

Science.gov (United States)

Itoh, Makoto; Fujiwara, Yusuke; Inagaki, Toshiyuki

This paper discusses driver's behavioral changes as a result of driver's use of an automatic brake system for preventing a rear-end collision from occurring. Three types of automatic brake systems are investigated in this study. Type 1 brake system applies a strong automatic brake when a collision is very imminent. Type 2 brake system initiates brake operation softly when a rear-end crash may be anticipated. Types 1 and 2 are for avoidance of a collision. Type 3 brake system, on the other hand, applies a strong automatic brake to reduce the damage when a collision can not be avoided. An experiment was conducted with a driving simulator in order to analyze the driver's possible behavioral changes. The results showed that the time headway (THW) during car following phase was reduced by use of an automatic brake system of any type. The inverse of time to collision (TTC), which is an index of the driver's brake timing, increased by use of Type 1 brake system when the deceleration rate of the lead vehicle was relatively low. However, the brake timing did not change when the drivers used Type 2 or 3 brake system. As a whole, dangerous behavioral changes, such as overreliance on a brake system, were not observed for either type of brake system.

Braking Control for Improving Ride Comfort

Directory of Open Access Journals (Sweden)

Lee Jonghyup

2018-01-01

Full Text Available While many vehicle control systems focus on vehicle safety and vehicle performance at high speeds, most driving conditions are very low risk situations. In such a driving situation, the ride comfort of the vehicle is the most important performance index of the vehicle. Electro mechanical brake (EMB and other brake-by-wire (BBW systems have been actively researched. As a result, braking actuators in vehicles are more freely controllable, and research on improving ride comfort is also possible. In this study, we develop a control algorithm that dramatically improves ride comfort in low risk braking situations. A method for minimizing the inconvenience of a passenger due to a suddenly changing acceleration at the moment when the vehicle is stopped is presented. For this purpose, an acceleration trajectory is generated that minimizes the discomfort index defined by the change in acceleration, jerk. A controller is also designed to track this trajectory. The algorithm that updates the trajectory is designed considering the error due to the phase lag occurring in the controller and the plant. In order to verify the performance of this controller, simulation verification is completed using a car simulator, Carsim. As a result, it is confirmed that the ride comfort is dramatically improved.

EEG potentials predict upcoming emergency brakings during simulated driving

Science.gov (United States)

Haufe, Stefan; Treder, Matthias S.; Gugler, Manfred F.; Sagebaum, Max; Curio, Gabriel; Blankertz, Benjamin

2011-10-01

Emergency braking assistance has the potential to prevent a large number of car crashes. State-of-the-art systems operate in two stages. Basic safety measures are adopted once external sensors indicate a potential upcoming crash. If further activity at the brake pedal is detected, the system automatically performs emergency braking. Here, we present the results of a driving simulator study indicating that the driver's intention to perform emergency braking can be detected based on muscle activation and cerebral activity prior to the behavioural response. Identical levels of predictive accuracy were attained using electroencephalography (EEG), which worked more quickly than electromyography (EMG), and using EMG, which worked more quickly than pedal dynamics. A simulated assistance system using EEG and EMG was found to detect emergency brakings 130 ms earlier than a system relying only on pedal responses. At 100 km h-1 driving speed, this amounts to reducing the braking distance by 3.66 m. This result motivates a neuroergonomic approach to driving assistance. Our EEG analysis yielded a characteristic event-related potential signature that comprised components related to the sensory registration of a critical traffic situation, mental evaluation of the sensory percept and motor preparation. While all these components should occur often during normal driving, we conjecture that it is their characteristic spatio-temporal superposition in emergency braking situations that leads to the considerable prediction performance we observed.

THEORETICAL BASIS OF PARAMETRIC SYNTHESIS FOR CARRYING SYSTEMS OF CARS

Directory of Open Access Journals (Sweden)

O. V. Fomin

2017-08-01

Full Text Available Purpose. The article is aimed to systematize and structure representation of theoretical grounds for the optimization designing of railway car components and practical ways of its implementation. Methodology. The study is based on analysis of several well-known articles on the subject, as well as on authors' researches, some mathematical foundations and computer modeling. The rolling stock components structural analysis was made by applying modern and acknowledged methods. Findings. In the study the authors systematized the set of methodological approaches to the freight car design processes; they also analyzed every application phase of the designing process and its conditions. The article presents the developed mathematical model of the car component implementation. This model takes into account all the calculated cases of the car life cycle. Moreover, the model also can be applied to other transport modes accounting their specific operation modes. The possibility to generate different construction options for equally strong car component with minimum material intensity was also shown in the article. There were several methods developed for finding optimal solutions that make it possible to calculate the sought characteristics of construction elements with the reliable accuracy. The presented variety of different approaches significantly extends engineering apparatus by increasing the synthesis and analysis abilities of the car design. Originality. The authors proposed the methodological foundations of the car components design aimed at creating their optimal structural parameter execution and the operating features based on the results of the detailed research. Practical value. Expediency and effectiveness of the presented methods has been confirmed by positive experience of its application when constructing the general-purpose gondola cars, models 12-9904 and 12-9904-01, as well as when upgrading existing constructions of freight cars, model

Forecasting freight flows

DEFF Research Database (Denmark)

Lyk-Jensen, Stéphanie

2011-01-01

Trade patterns and transport markets are changing as a result of the growth and globalization of international trade, and forecasting future freight flow has to rely on trade forecasts. Forecasting freight flows is critical for matching infrastructure supply to demand and for assessing investment...... constitute a valuable input to freight models for forecasting future capacity problems.......Trade patterns and transport markets are changing as a result of the growth and globalization of international trade, and forecasting future freight flow has to rely on trade forecasts. Forecasting freight flows is critical for matching infrastructure supply to demand and for assessing investment...

Braking Deceleration Measurement Using the Video Analysis of Motions by Sw Tracker

Directory of Open Access Journals (Sweden)

Ondruš Ján

2015-06-01

Full Text Available This contribution deals with the issue of car braking, particularly with the one of M1 category. Braking deceleration measurement of the vehicle Mazda 3 MPS was carried out by the declerograph XL MeterTM Pro. The main aim of the contribution is to perform comparison of the process of braking deceleration between the decelograph and the new alternative method of video analysis and to subsequently examine these processes. The test took place at the Rosina airfield, the airstrip in a small village nearby the town of Žilina. The last part of this paper presents the results, evlauation and comparison of the measurements carried out.

Analysis of the nonlinear dynamics of a 2-axle freight wagon in curves

DEFF Research Database (Denmark)

Di Gialleonardo, Egidio; Bruni, Stefano; True, Hans

2014-01-01

This paper deals with the study of the nonlinear dynamic behaviour of 2-axle freight wagons in curves, considering the case of one single wagon (neglecting inter-car coupling forces) and of multiple wagons interacting through the buffers and the couplers. A multi-body model of a single wagon...... and of a three-car assembly is introduced, paying particular attention to the nonlinear and nonsmooth modelling of the suspensions and of the inter-car coupling elements. Using this model, a numerical analysis of the steady-state solution reached after the negotiation of curve transition is presented......, it is shown that the coupling forces exchanged by the wagons significantly affect their dynamics in a curve, reducing the amplitude of vibration....

Numerical Investigation of Aerodynamic Braking for a Ground Vehicle

Science.gov (United States)

Devanuri, Jaya Krishna

2018-06-01

The purpose of this article is to observe the effect of an air brake on the aerodynamics of a ground vehicle and also to study the influence of change in the parameters like the velocity of the vehicle, the angle of inclination, height, and position of the air brake on the aerodynamics of the vehicle body. The test subject used is an Ahmed body which is a generic 3D car body as it retains all the aerodynamic characteristics of a ground vehicle. Numerical investigation has been carried out by RNG k-ɛ turbulence model. Results are presented in terms of streamlines and drag coefficient to understand the influence of pertinent parameters on flow physics. It is found that with the use of an air brake, though the drag coefficient remains more or less constant with velocity, it increases with the increase in height and angle of inclination of the air brake. But the effect of position of air brake on the coefficient of drag is surprising since for certain heights of the air brake the drag coefficient is maximum at the foremost point and as the air brake moves towards the rear it is first observed to decrease and then increase. It is also observed that with the increase in height of the air brake the drag coefficient monotonically decreases as the position of the air brake is moved towards the rear. Taguchi method has been employed with L16 orthogonal array to obtain the optimal configuration for the air brake. For each of the selected parameters, four different levels have been chosen to obtain the maximum drag coefficient value. The study could provide an invaluable database for the optimal design of an airbrake for a ground vehicle.

Diagnostics monitor of the braking efficiency in the on board diagnostics system for the motor vehicles

Science.gov (United States)

Gajek, Andrzej

2016-09-01

The article presents diagnostics monitor for control of the efficiency of brakes in various road conditions in cars equipped with pressure sensor in brake (ESP) system. Now the brake efficiency of the vehicles is estimated periodically in the stand conditions on the base of brake forces measurement or in the road conditions on the base of the brake deceleration. The presented method allows to complete the stand - periodical tests of the brakes by current on board diagnostics system OBD for brakes. First part of the article presents theoretical dependences between deceleration of the vehicle and brake pressure. The influence of the vehicle mass, initial speed of braking, temperature of brakes, aerodynamic drag, rolling resistance, engine resistance, state of the road surface, angle of the road sloping on the deceleration have been analysed. The manner of the appointed of these parameters has been analysed. The results of the initial investigation have been presented. At the end of the article the strategy of the estimation and signalization of the irregular value of the deceleration are presented.

Using naturalistic driving study data to investigate the impact of driver distraction on driver's brake reaction time in freeway rear-end events in car-following situation.

Science.gov (United States)

Gao, Jingru; Davis, Gary A

2017-12-01

The rear-end crash is one of the most common freeway crash types, and driver distraction is often cited as a leading cause of rear-end crashes. Previous research indicates that driver distraction could have negative effects on driving performance, but the specific association between driver distraction and crash risk is still not fully revealed. This study sought to understand the mechanism by which driver distraction, defined as secondary task distraction, could influence crash risk, as indicated by a driver's reaction time, in freeway car-following situations. A statistical analysis, exploring the causal model structure regarding drivers' distraction impacts on reaction times, was conducted. Distraction duration, distraction scenario, and secondary task type were chosen as distraction-related factors. Besides, exogenous factors including weather, visual obstruction, lighting condition, traffic density, and intersection presence and endogenous factors including driver age and gender were considered. There was an association between driver distraction and reaction time in the sample freeway rear-end events from SHRP 2 NDS database. Distraction duration, the distracted status when a leader braked, and secondary task type were related to reaction time, while all other factors showed no significant effect on reaction time. The analysis showed that driver distraction duration is the primary direct cause of the increase in reaction time, with other factors having indirect effects mediated by distraction duration. Longer distraction duration, the distracted status when a leader braked, and engaging in auditory-visual-manual secondary task tended to result in longer reaction times. Given drivers will be distracted occasionally, countermeasures which shorten distraction duration or avoid distraction presence while a leader vehicle brakes are worth considering. This study helps better understand the mechanism of freeway rear-end events in car-following situations, and

The freight landscape : using secondary data sources to describe metropolitan freight flows.

Science.gov (United States)

2015-12-01

Metropolitan areas around the world are seeking to better manage freight flows and reduce negative impacts on local populations. A major challenge to better urban freight management is the lack of data; little is known about freight movements at the ...

An Analytical Design Method for a Regenerative Braking Control System for DC-electrified Railway Systems under Light Load Conditions

Science.gov (United States)

Saito, Tatsuhito; Kondo, Keiichiro; Koseki, Takafumi

A DC-electrified railway system that is fed by diode rectifiers at a substation is unable to return the electric power to an AC grid. Accordingly, the braking cars have to restrict regenerative braking power when the power consumption of the powering cars is not sufficient. However, the characteristics of a DC-electrified railway system, including the powering cars, is not known, and a mathematical model for designing a controller has not been established yet. Hence, the object of this study is to obtain the mathematical model for an analytical design method of the regenerative braking control system. In the first part of this paper, the static characteristics of this system are presented to show the position of the equilibrium point. The linearization of this system at the equilibrium point is then performed to describe the dynamic characteristics of the system. An analytical design method is then proposed on the basis of these characteristics. The proposed design method is verified by experimental tests with a 1kW class miniature model, and numerical simulations.

Benefits of magnesium wheels for consumer cars

Science.gov (United States)

Frishfelds, Vilnis; Timuhins, Andrejs; Bethers, Uldis

2018-05-01

Advantages and disadvantages of magnesium wheels are considered based on a mechanical model of a car. Magnesium wheels are usually applied to racing cars as they provide slightly better strength/weight ratio than aluminum alloys. Do they provide notable benefits also for the everyday user when the car speeds do not exceed allowed speed limit? Distinct properties of magnesium rims are discussed. Apart from lighter weight of magnesium alloys, they are also good in dissipating the energy of vibrations. The role of energy dissipation in the rim of a wheel is estimated by a quarter car model. Improvements to safety by using the magnesium wheels are considered. Braking distance and responsiveness of the car is studied both with and without using an Anti Blocking System (ABS). Influence of rim weight on various handling parameters of the car is quantitatively tested.

14 CFR 25.735 - Brakes and braking systems.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Brakes and braking systems. 25.735 Section... braking systems. (a) Approval. Each assembly consisting of a wheel(s) and brake(s) must be approved. (b... an automatic braking system is installed, means are provided to: (i) Arm and disarm the system, and...

Development of brake assist system. Summary of hydraulic brake assist system; Brake assist system no kaihatsu. Ekiatsushiki brake assist system no gaiyo

Energy Technology Data Exchange (ETDEWEB)

Hara, M; Ota, M; Shimizu, S [Toyota, Motor Corp., Aichi (Japan)

1997-10-01

We have already developed vacuum-booster-type Brake Assist System that supplies additional braking power when panic braking is recognized. We are convinced that the expansion of Brake Assist System will become more important issue in the future. Therefore we have developed hydraulic Brake Assist System with increasing its controllability and reducing its discomfort. This system have a brake pressure sensor to detect emergency braking operation and an antilock device to supply additional braking power. 8 refs., 11 figs.

Thermal measurement of brake pad lining surfaces during the braking process

Science.gov (United States)

Piątkowski, Tadeusz; Polakowski, Henryk; Kastek, Mariusz; Baranowski, Pawel; Damaziak, Krzysztof; Małachowski, Jerzy; Mazurkiewicz, Łukasz

2012-06-01

This paper presents the test campaign concept and definition and the analysis of the recorded measurements. One of the most important systems in cars and trucks are brakes. The braking temperature on a lining surface can rise above 500°C. This shows how linings requirements are so strict and, what is more, continuously rising. Besides experimental tests, very supportive method for investigating processes which occur on the brake pad linings are numerical analyses. Experimental tests were conducted on the test machine called IL-68. The main component of IL-68 is so called frictional unit, which consists of: rotational head, which convey a shaft torque and where counter samples are placed and translational head, where samples of coatings are placed and pressed against counter samples. Due to the high rotational speeds and thus the rapid changes in temperature field, the infrared camera was used for testing. The paper presents results of analysis registered thermograms during the tests with different conditions. Furthermore, based on this testing machine, the numerical model was developed. In order to avoid resource demanding analyses only the frictional unit (described above) was taken into consideration. Firstly the geometrical model was performed thanks to CAD techniques, which in the next stage was a base for developing the finite element model. Material properties and boundary conditions exactly correspond to experimental tests. Computations were performed using a dynamic LS-Dyna code where heat generation was estimated assuming full (100%) conversion of mechanical work done by friction forces. Paper presents the results of dynamic thermomechanical analysis too and these results were compared with laboratory tests.

Urban freight distribution: council warehouses & freight by rail

Directory of Open Access Journals (Sweden)

Aleksander SŁADKOWSKI

2014-10-01

Full Text Available Rail is the one of the highly underused form of freight transportation in the European Union. Majority of the freightage are distributed by trucks and HGVs. With new regulations and socio-environmental concerns urban logistics is facing a new challenge which can be tackled using innovative transport mechanisms and streamline operations. This article sheds light on a system which integrates freight distribution via metro lines in the closest vicinity of the customer, use of council warehouses and further innovative transport mechanisms for final delivery. This system uses existing infrastructure effectively without impacting its surroundings and triggers the reduction of polluting carriers. This system offers the option of immediate implementation which will enable EU to compete with a global freight distribution market.

Formulation of Equations of Motion for a Simply Supported Bridge under a Moving Railway Freight Vehicle

Directory of Open Access Journals (Sweden)

Ping Lou

2007-01-01

Full Text Available Based on energy approach, the equations of motion in matrix form for the railway freight vehicle-bridge interaction system are derived, in which the dynamic contact forces between vehicle and bridge are considered as internal forces. The freight vehicle is modelled as a multi-rigid-body system, which comprises one car body, two bogie frames and four wheelsets. The bogie frame is linked with the car body through spring-dashpot suspension systems, and the bogie frame is rigidly linked with wheelsets. The bridge deck, together with railway track resting on bridge, is modelled as a simply supported Bernoulli-Euler beam and its deflection is described by superimposing modes. The direct time integration method is applied to obtain the dynamic response of the vehicle-bridge interaction system at each time step. A computer program has been developed for analyzing this system. The correctness of the proposed procedure is confirmed by one numerical example. The effect of different beam mode numbers and various surface irregularities of beam on the dynamic responses of the vehicle-bridge interaction system are investigated.

Economic Analysis Framework for Freight Transportation Based on Florida Statewide Multi-Modal Freight Model

Science.gov (United States)

2018-02-01

Freight transportation plays a vital role in local and regional economy. The markets and businesses from different regions and locations can be connected through freight movements. But it is difficult to quantify the economic contribution of freight ...

The freight landscape : using secondary data sources to describe metropolitan freight flows : final report.

Science.gov (United States)

2015-12-01

Metropolitan areas around the world are seeking to better manage freight flows and reduce negative impacts on local populations. A major challenge to better urban freight management is the lack of data; little is known about freight movements at the ...

Transient switching control strategy from regenerative braking to anti-lock braking with a semi-brake-by-wire system

Science.gov (United States)

Li, Liang; Li, Xujian; Wang, Xiangyu; Liu, Yahui; Song, Jian; Ran, Xu

2016-02-01

Regenerative braking is an important technology in improving fuel economy of an electric vehicle (EV). However, additional motor braking will change the dynamic characteristics of the vehicle, leading to braking instability, especially when the anti-lock braking system (ABS) is triggered. In this paper, a novel semi-brake-by-wire system, without the use of a pedal simulator and fail-safe device, is proposed. In order to compensate for the hysteretic characteristics of the designed brake system while ensure braking reliability and fuel economy when the ABS is triggered, a novel switching compensation control strategy using sliding mode control is brought forward. The proposed strategy converts the complex coupling braking process into independent control of hydraulic braking and regenerative braking, through which a balance between braking performance, braking reliability, braking safety and fuel economy is achieved. Simulation results show that the proposed strategy is effective and adaptable in different road conditions while the large wheel slip rate is triggered during a regenerative braking course. The research provides a new possibility of low-cost equipment and better control performance for the regenerative braking in the EV and the hybrid EV.

Computer Security: your car, my control

CERN Multimedia

Stefan Lueders, Computer Security Team

2015-01-01

We have discussed the Internet of Things (IoT) and its security implications already in past issues of the CERN Bulletin, for example in “Today’s paranoia, tomorrow’s reality” (see here). Unfortunately, tomorrow has come. At this years's Black Hat conference researchers presented their findings on how easily your car can be hacked and controlled remotely. Sigh.   While these researchers have just shown that they can wirelessly hijack a Jeep Cherokee, others have performed similar studies with SmartCars, Fords, a Tesla, a Corvette, BMWs, Chryslers and Mercedes! With the increasing computerisation of cars, the engine management system, air conditioning, anti-lock braking system, electronic stability programme, etc. are linked to the infotainment, navigation and communication systems, opening the door for these vehicles to be hacked remotely. The now prevalent Bluetooth connection with smartphones is one entry vector to attack your car remotely...

New regenerative braking control strategy for rear-driven electrified minivans

International Nuclear Information System (INIS)

Junzhi, Zhang; Yutong, Li; Chen, Lv; Ye, Yuan

2014-01-01

Highlights: • A regenerative braking system is designed for a rear-driven electric minivan. • A new control strategy coordinating energy efficiency and braking feel is proposed. • The control strategy is verified by simulation and hardware-in-loop (HIL) tests. • The proposed control strategy offers higher regeneration efficiency. - Abstract: As of to 2012, minivan ownership stood at 20 million units in China, accounting for 16% of the passenger car market. In this article, comprehensive research is carried out on the design and control of a regenerative braking system for a rear-driven electrified minivan. For improving the regeneration efficiency by as much as possible, a new regenerative braking control strategy called “modified control strategy” is proposed. Additionally, a control strategy called “baseline control strategy” is introduced as a comparative control strategy. Simulations and hardware-in-loop (HIL) tests are carried out. The results of the simulations and the HIL tests show that the modified control strategy offers considerably higher regeneration efficiency than the baseline control strategy. In normal deceleration braking, the regeneration efficiency of the modified control strategy reaches 47%, 15% higher than that of the baseline control strategy. In addition, improvement in the fuel economy of electric vehicles operating on the ECE driving cycle and enhanced with the modified control strategy is greater than 10%, which is 3% higher than that with the baseline control strategy

THE MOMENT OF UNSAFETY FOR DRIVING IN CONDITIONS OF POOR VISIBILITY TAKING INTO ACCOUNT THE EVALUATION OF VEHICLE BRAKING EFFICIENCY

Directory of Open Access Journals (Sweden)

A. Sarayev

2014-02-01

Full Text Available This study is aimed at investigation of a car collision with a pedestrian under limited visibility condi-tions. For this purpose an expert has to analyze the accident details and determine the critical time at which the car driver must take an action to avoid the collision. The analysis is complicated due to the fact that the vehicle is equipped with an anti-blocking braking system and does not leave a braking trace on the pavement. In this case, a relevant expert analysis technique does not exist. The development of such techniques as the basis of this scientific work is given.

Simulation of longitudinal dynamics of long freight trains in positioning operations

Science.gov (United States)

Qi, Zhaohui; Huang, Zhihao; Kong, Xianchao

2012-09-01

Positioning operations are performed in a railway goods yard, in which the freight train is pulled precisely at a specific point by a positioner. The positioner moves strictly according to the predesigned speed and provides all the traction and braking forces which are highly dependent on the longitudinal dynamic response. In order to improve the efficiency and protect the wagons from damage during positioning operations, the design speed of the positioner has to be optimised based on the simulation of longitudinal train dynamics. However, traditional models of longitudinal train dynamics are not accurate enough in some aspects. In this study, we make some changes in the traditional theory to make it suitable for the study of long freight trains in positioning operations. In the proposed method, instead of the traction force on the train, the motion of the positioner is assumed to be known; more importantly, the traditional draft gear model with nonlinear spring and linear damping is replaced by a more detailed model based on the achievement of contact and impact mechanics; the switching effects of the resistance and the coupler slack are also taken into consideration. Numerical examples that deal with positioning operations on the straight lines, slope lines and curving lines are given.

Freight from space : evaluating freight activity and emissions from satellite data.

Science.gov (United States)

2013-06-01

In this report, the authors investigate the current state of knowledge of freight transport emissions, the importance of freight emissions relative to other sources, and what tools are available, or can be developed to answer these questions and impr...

Development of hydraulic brake actuator for active brake control; Active brake seigyoyo yuatsu booster no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Konishi, Y; Hattori, M. Sugisawa, M.; Nishii, M [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

Recently, application of active brake control systems of the vehicle are increasing. (Vehicle stability control, Panic brake assist ) We have developed a new hydraulic brake actuator for active brake control systems. New hydraulic brake actuator is composed of the three parts. (Hydraulic booster unit, Power supply unit, Control valve unit) This report describes the construction of the new hydraulic booster unit. 2 refs., 10 figs.

49 CFR 232.105 - General requirements for locomotives.

Science.gov (United States)

2010-10-01

... locomotives. (a) The air brake equipment on a locomotive shall be in safe and suitable condition for service... set pressure at any service application with the brakes control valve in the freight position. If such... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR FREIGHT AND OTHER NON-PASSENGER...

Freight transport and intermodality

OpenAIRE

Barbero Mañanes, Eduardo

2010-01-01

During recent decades, there has been very substantial growth in the freight transport sector. Freight transport is increasing faster than the economy or passenger transport. Demand is increasing more rapidly than supply and is resulting in environmental and social problems. Increasing congestion, too, is affecting efficient and reliable freight distribution, and consequently having a deleterious effect on local economies. Intermodality is therefore needed to make better use of alternative mo...

A mechanical brake hardware-in-the-loop simulation of a railway vehicle that accounts for hysteresis and pneumatic cylinder dynamics

Directory of Open Access Journals (Sweden)

Dong-Chan Lee

2015-11-01

Full Text Available A brake hardware-in-the-loop simulation system for a railway vehicle provides an effective platform for testing the braking performance under various dangerous braking conditions. However, in general, four-brake calipers are required to implement a mechanical brake system for one car. In this article, we implement a brake hardware-in-the-loop simulation system only with one brake caliper and three air tanks accounting for hysteresis and pneumatic cylinder dynamics, ultimately saving installation space and reducing financial budget costs. Since the brake caliper has a high nonlinearity, such as hysteresis resulting from friction and from the precompressed spring of the brake cylinder, we measured the hysteresis of the brake caliper clamping force for a mechanical brake system using loadcells, based on which a mathematical model was constructed for the hysteresis of the clamping force between the brake pad and the disk. Moreover, the pneumatic cylinder dynamics are identified and are implemented in three air tanks, together with hysteresis nonlinearity. The proposed brake hardware-in-the-loop simulation system is applied to the wheel-slide protection simulation of a railway vehicle with an initial speed of 80 km/h and demonstrated experimentally accounting for the hysteresis and brake cylinder dynamics.

Braking System Modeling and Brake Temperature Response to Repeated Cycle

Directory of Open Access Journals (Sweden)

Zaini Dalimus

2014-12-01

Full Text Available Braking safety is crucial while driving the passenger or commercial vehicles. Large amount of kinetic energy is absorbed by four brakes fitted in the vehicle. If the braking system fails to work, road accident could happen and may result in death. This research aims to model braking system together with vehicle in Matlab/Simulink software and measure actual brake temperature. First, brake characteristic and vehicle dynamic model were generated to estimate friction force and dissipated heat. Next, Arduino based prototype brake temperature monitoring was developed and tested on the road. From the experiment, it was found that brake temperature tends to increase steadily in long repeated deceleration and acceleration cycle.

Freight from Space: Evaluating Freight Activity and Emissions Trends from Satellite Data

Science.gov (United States)

Bickford, E.; Holloway, T.; Oberman, J.; Janssen, M.

2012-12-01

Heavy duty diesel freight trucks are the fastest growing source of highway emissions in the U.S., with domestic freight tonnage projected to double by 2050. Highway diesel vehicles currently account for 42% of on-road emissions of nitrogen oxides (NOx), 58% of on-road fine particulate (PM2.5) emissions, and 21% of on-road carbon dioxide emissions. Because most surface air quality monitors are located in densely populated areas and not rural highways, it is difficult to use ground-based observations to validate spatial trends in transportation emissions. Therefore, we have employed satellite retrievals from the OMI instrument to inform surface freight transportation inventory estimates by validating modeled tropospheric vertical column total nitrogen dioxide (NO2) against satellite observations. For this research we built a roadway-by-roadway bottom-up diesel truck emissions inventory using GIS, the U.S. Federal Highway Administration's Freight Analysis Framework (FAF) activity dataset, and the U.S. Environmental Protection Agency's MOVES emissions model. We use freight rail emissions from the Eastern Regional Technical Advisory Committee (ERTAC), inventory emissions from the Lake Michigan's Air Directors Consortium (LADCO) and the EPA's Community Multiscale Air Qualiy (CMAQ) model to simulate ground-level and tropospheric column concentrations of NO2. We also use the combination of models and satellite data to evaluate weekday-weekend patterns of NO2 concentrations and the relative contributions of highway diesel vehicles, highway gasoline vehicles, and freight rail to transportation-related pollution. This research presents the first evaluation of surface freight transport from space-based observations. We find satellite retrievals of surface pollutants provide a useful data tool for evaluating air quality models and constraining emissions sources.

Sprag solenoid brake

Science.gov (United States)

Dane, P. H.

1972-01-01

Operation of solenoid braking mechanism is discussed. Illustrations of construction of the brake are provided. Device is used for braking low or medium speed shaft rotations and produces approximately ten times braking torque of similar solenoid brakes.

Braking system

Science.gov (United States)

Norgren, D.U.

1982-09-23

A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

Fatal crashes of passenger vehicles before and after adding antilock braking systems.

Science.gov (United States)

Farmer, C M; Lund, A K; Trempel, R E; Braver, E R

1997-11-01

Fatal crash rates of passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. Vehicles selected for analysis had no other significant design changes between the model years being compared, and the model years with and without antilocks were no more than two years apart. The overall fatal crash rates were similar for the two model years. However, the vehicles with antilocks were significantly more likely to be involved in crashes fatal to their own occupants, particularly single-vehicle crashes. Conversely, antilock vehicles were less likely to be involved in crashes fatal to occupants of other vehicles or nonoccupants (pedestrians, bicyclists). Overall, antilock brakes appear to have had little effect on fatal crash involvement. Further study is needed to better understand why fatality risk has increased for occupants of antilock vehicles.

Brake response time is significantly impaired after total knee arthroplasty: investigation of performing an emergency stop while driving a car.

Science.gov (United States)

Jordan, Maurice; Hofmann, Ulf-Krister; Rondak, Ina; Götze, Marco; Kluba, Torsten; Ipach, Ingmar

2015-09-01

The objective of this study was to investigate whether total knee arthroplasty (TKA) impairs the ability to perform an emergency stop. An automatic transmission brake simulator was developed to evaluate total brake response time. A prospective repeated-measures design was used. Forty patients (20 left/20 right) were measured 8 days and 6, 12, and 52 wks after surgery. Eight days postoperative total brake response time increased significantly by 30% in right TKA and insignificantly by 2% in left TKA. Brake force significantly decreased by 35% in right TKA and by 25% in left TKA during this period. Baseline values were reached at week 12 in right TKA; the impairment of outcome measures, however, was no longer significant at week 6 compared with preoperative values. Total brake response time and brake force in left TKA fell below baseline values at weeks 6 and 12. Brake force in left TKA was the only outcome measure significantly impaired 8 days postoperatively. This study highlights that categorical statements cannot be provided. This study's findings on automatic transmission driving suggest that right TKA patients may resume driving 6 wks postoperatively. Fitness to drive in left TKA is not fully recovered 8 days postoperatively. If testing is not available, patients should refrain from driving until they return from rehabilitation.

WHAT WAY DETERMINE THE CORRECT ALLOCATION AND LAYOUT FOR THE NEEDS OF PARKING FREIGHT DESIGN IN CONCRETE REGION

Directory of Open Access Journals (Sweden)

Martin Straka

2014-12-01

Full Text Available In terms of building a network parking strategies for freight transport may be considered two variants: a building (completing car parks on abandoned of border crossings, respectively building a whole new network of parks. Creating a network of parks for freight is in the interest of the Slovak Republic as well as the European Union. The subsequent optimization is dependent on the quality of road infrastructure and the traffic intensity in the monitored sections. It is therefore important selection of suitable candidates, administrators and their subsequent assessment of the appropriateness and services provided in selected locations. Identification of parking in the SR enables to choose the effective solution for intelligent networking and secure parking.

Performance of collision damage mitigation braking systems and their effects on human injury in the event of car-to-pedestrian accidents.

Science.gov (United States)

Matsui, Yasuhiro; Han, Yong; Mizuno, Koji

2011-11-01

The number of traffic deaths in Japan was 4,863 in 2010. Pedestrians account for the highest number (1,714, 35%), and vehicle occupants the second highest (1,602, 33%). Pedestrian protection is a key countermeasure to reduce casualties in traffic accidents. A striking vehicle's impact velocity could be considered a parameter influencing the severity of injury and possibility of death in pedestrian crashes. A collision damage mitigation braking system (CDMBS) using a sensor to detect pedestrians could be effective for reducing the vehicle/pedestrian impact velocity. Currently in Japan, cars equipped with the CDMBS also have vision sensors such as a stereo camera for pedestrian detection. However, the ability of vision sensors in production cars to properly detect pedestrians has not yet been established. The effect of reducing impact velocity on the pedestrian injury risk has also not been determined. The first objective of this study is to evaluate the performance of the CDMBS in detecting pedestrians when it is installed in production cars. The second objective of this study is to evaluate the effect of reducing impact velocity on mitigating pedestrian injury. Firstly, impact experiments were performed using a car with the CDMBS in which the car collided with a pedestrian surrogate. In these tests, the velocity was chosen for the various test runs to be 20, 40 and 60 km/h, respectively, which were based on the velocity distribution in real-world pedestrian crashes. The results indicated that the impact velocity reduction ranged approximately from 10 to 15 km/h at the standing location of a pedestrian surrogate at both daytime and nighttime lighting conditions. These results show that the system has the potential to reduce pedestrian casualties from car-to-pedestrian contacts. Secondly, finite-element analyses were performed simulating vehicle-to- pedestrian impacts with the THUMS pedestrian models. The vehicle models selected for the study included a medium sedan

Detection of visually unrecognizable braking tracks using Laser-Induced Breakdown Spectroscopy, a feasibility study

Science.gov (United States)

Prochazka, David; Bilík, Martin; Prochazková, Petra; Brada, Michal; Klus, Jakub; Pořízka, Pavel; Novotný, Jan; Novotný, Karel; Ticová, Barbora; Bradáč, Albert; Semela, Marek; Kaiser, Jozef

2016-04-01

Identification of the position, length and mainly beginning of a braking track has proven to be essential for determination of causes of a road traffic accident. With the introduction of modern safety braking systems and assistance systems such as the Anti-lock Braking System (ABS) or Electronic Stability Control (ESC), the visual identification of braking tracks that has been used up until the present is proving to be rather complicated or even impossible. This paper focuses on identification of braking tracks using a spectrochemical analysis of the road surface. Laser-Induced Breakdown Spectroscopy (LIBS) was selected as a method suitable for fast in-situ element detection. In the course of detailed observations of braking tracks it was determined that they consist of small particles of tire treads that are caught in intrusions in the road surface. As regards detection of the "dust" resulting from wear and tear of tire treads in the environment, organic zinc was selected as the identification element in the past. The content of zinc in tire treads has been seen to differ with regard to various sources and tire types; however, the arithmetic mean and modus of these values are approximately 1% by weight. For in-situ measurements of actual braking tracks a mobile LIBS device equipped with a special module was used. Several measurements were performed for 3 different cars and tire types respectively which slowed down with full braking power. Moreover, the influence of different initial speed, vehicle mass and braking track length on detected signal is discussed here.

Research on Braking Stability of Electro-mechanical Hybrid Braking System in Electric Vehicles

OpenAIRE

Ji, Fenzhu; Tian, Mi

2010-01-01

For the electro-mechanical hybrid braking system, which is composed of electric brake and general friction brake, the models of electric braking force, total braking force and the utilization adhesion coefficient for front and rear axles were established based on the analysis of braking torque distribution. The variation relationship between electric braking force and friction braking force in different braking intensity was calculated and analyzed with the paralleled-hybridized braking contr...

Automotive Brake Systems.

Science.gov (United States)

Marine Corps Inst., Washington, DC.

This correspondence course, orginally developed for the Marine Corps, is designed to provide mechanics with an understanding of the basic operations of automotive brake systems on military vehicles. The course contains four study units covering hydraulic brakes, air brakes, power brakes, and auxiliary brake systems. A troubleshooting guide for…

Gravity brake

Science.gov (United States)

Lujan, Richard E.

2001-01-01

A mechanical gravity brake that prevents hoisted loads within a shaft from free-falling when a loss of hoisting force occurs. A loss of hoist lifting force may occur in a number of situations, for example if a hoist cable were to break, the brakes were to fail on a winch, or the hoist mechanism itself were to fail. Under normal hoisting conditions, the gravity brake of the invention is subject to an upward lifting force from the hoist and a downward pulling force from a suspended load. If the lifting force should suddenly cease, the loss of differential forces on the gravity brake in free-fall is translated to extend a set of brakes against the walls of the shaft to stop the free fall descent of the gravity brake and attached load.

Monte Carlo study of holding forces for tank cars on grades

Science.gov (United States)

2013-04-15

This paper describes a numerical procedure to examine the holding forces needed to secure a cut of railroad tank cars staged on a grade during loading and unloading operations. Holding forces are created by applying emergency brake systems and blocki...

High performance brake discs made of fiber reinforced ceramics; Hochleistungsbremsscheiben aus Faserverbundkeramik

Energy Technology Data Exchange (ETDEWEB)

Rosenloecher, J.; Deinzer, G.; Waninger, R.; Muenchhoff, J. [AUDI AG, 85045 Ingolstadt (Germany)

2007-11-15

The Audi AG is one of the worldwide leading car manufacturers of the premium class. One of the main aims of the technical development department at Audi is the use of novel and innovative materials. The Audi AG has intensively worked on the development and introduction of ceramic brake discs for several car types. These brake discs are made of a short carbon fiber reinforced silicon carbide ceramic, a so called CMC-material (ceramic matrix composite). This material is produced in a very complex process by silicon melt infiltration of carbon preforms. The advantages of these innovative and powerful brake discs out of C/SiC-ceramic are the low weight and thus the reduction of the unsprung rotating masses, the low wear rate during completed service life, the temperature and fading stability and the corrosion resistance. The complete braking system and its periphery had to be reengineered and adjusted because of the specific material properties. (Abstract Copyright [2007], Wiley Periodicals, Inc.) [German] Die Audi AG ist einer der weltweit fuehrenden Automobilhersteller der Premiumklasse. Eines der Hauptziele der Technischen Entwicklung bei Audi ist der Einsatz neuartiger und innovativer Werkstoffe. Daher bietet die Audi AG nach intensiver Entwicklung und Erprobung fuer mehrere Fahrzeugmodelle Keramikbremsscheiben an. Diese Bremsscheiben bestehen aus einer kohlenstoffkurzfaserverstaerkten Siliziumkarbidkeramik, einem sog. CMC-Werkstoff. Dieser Werkstoff wird in einem aufwendigen Verfahren ueber die Schmelzinfiltration von Kohlenstoff-Preformen mit Silizium hergestellt. Die Vorteile dieser innovativen und leistungsfaehigen Bremsscheiben aus C/SiC-Keramik sind das geringe Gewicht und dadurch die Reduzierung der ungefederten rotierenden Massen, der geringe Verschleiss ueber Betriebsdauer, die Temperatur- und Fadingstabilitaet und die Korrosionsbestaendigkeit. Aufgrund der materialspezifischen Eigenschaften wurde das gesamte Bremssystem ueberarbeitet und die

Multimodal freight investment criteria.

Science.gov (United States)

2010-07-01

Literature was reviewed on multi-modal investment criteria for freight projects, examining measures and techniques for quantifying project benefits and costs, as well as ways to describe the economic importance of freight transportation. : A limited ...

Assessing sustainable freight policies.

Science.gov (United States)

2014-05-01

The main aim of the study was to examine transportation demand management strategies related to long haul freight. It investigates freight : movements and truck vehicle miles traveled (TVMT) changes in response to certain transportation policies, inc...

New evidence concerning fatal crashes of passenger vehicles before and after adding antilock braking systems.

Science.gov (United States)

Farmer, C M

2001-05-01

Fatal crash rates for passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. A prior study, based on fatal crash experience through 1995, reported that vehicle models with antilock brakes were more likely than identical but 1-year-earlier models to be involved in crashes fatal to their own occupants, but were less likely to be involved in crashes fatal to occupants of other vehicles. Overall, there was no significant effect of antilocks on the likelihood of fatal crashes. Similar analyses, based on fatal crash experience during 1996-98, yielded very different results. During 1996-98, vehicles with antilock brakes were again less likely than earlier models to be involved in crashes fatal to occupants of other vehicles, but they were no longer overinvolved in crashes fatal to their own occupants.

Robust Switched Predictive Braking Control for Rollover Prevention in Wheeled Vehicles

Directory of Open Access Journals (Sweden)

Martín Antonio Rodríguez Licea

2014-01-01

Full Text Available The aim of this paper is to propose a differential braking rollover mitigation strategy for wheeled vehicles. The strategy makes use of a polytopic (piecewise linear description of the vehicle and includes translational and rotational dynamics, as well as suspension effects. The braking controller is robust and the system states are predicted to estimate the rollover risk up to a given time horizon. In contrast to existing works, the switched predictive nature of the control allows it to be applied only when risk of rollover is foreseen, interfering a minimum with driver’s actions. The stability of the strategy is analyzed and its robustness is illustrated via numerical simulations using CarSim for a variety of vehicles.

Extended-Kalman-filter-based regenerative and friction blended braking control for electric vehicle equipped with axle motor considering damping and elastic properties of electric powertrain

Science.gov (United States)

Lv, Chen; Zhang, Junzhi; Li, Yutong

2014-11-01

Because of the damping and elastic properties of an electrified powertrain, the regenerative brake of an electric vehicle (EV) is very different from a conventional friction brake with respect to the system dynamics. The flexibility of an electric drivetrain would have a negative effect on the blended brake control performance. In this study, models of the powertrain system of an electric car equipped with an axle motor are developed. Based on these models, the transfer characteristics of the motor torque in the driveline and its effect on blended braking control performance are analysed. To further enhance a vehicle's brake performance and energy efficiency, blended braking control algorithms with compensation for the powertrain flexibility are proposed using an extended Kalman filter. These algorithms are simulated under normal deceleration braking. The results show that the brake performance and blended braking control accuracy of the vehicle are significantly enhanced by the newly proposed algorithms.

Cooperative Control of Regenerative Braking and Antilock Braking for a Hybrid Electric Vehicle

OpenAIRE

Yin, Guodong; Jin, XianJian

2013-01-01

A new cooperative braking control strategy (CBCS) is proposed for a parallel hybrid electric vehicle (HEV) with both a regenerative braking system and an antilock braking system (ABS) to achieve improved braking performance and energy regeneration. The braking system of the vehicle is based on a new method of HEV braking torque distribution that makes the antilock braking system work together with the regenerative braking system harmoniously. In the cooperative braking control strategy, a sli...

Proposal to use vibration analysis steering components and car body to monitor, for example, the state of unbalance wheel

Science.gov (United States)

Janczur, R.

2016-09-01

The results of road tests of car VW Passat equipped with tires of size 195/65 R15, on the influence of the unbalancing front wheel on vibration of the parts of steering system, steering wheel and the body of the vehicle have been presented in this paper. Unbalances wheels made using weights of different masses, placed close to the outer edge of the steel rim and checked on the machine Hunter GSP 9700 for balancing wheels. The recorded waveforms vibration steering components and car body, at different constant driving speeds, subjected to spectral analysis to determine the possibility of isolating vibration caused by unbalanced wheel in various states and coming from good quality asphalt road surface. The results were discussed in terms of the possibility of identifying the state of unbalancing wheels and possible changes in radial stiffness of the tire vibration transmitted through the system driving wheel on the steering wheel. Vibration analysis steering components and car body, also in the longitudinal direction, including information from the CAN bus of the state of motion of the car, can be used to monitor the development of the state of unbalance wheel, tire damage or errors shape of brake discs or brake drums, causing pulsations braking forces.

Development of combined brake system on front and rear brakes for scooter; Scooter yo zenkorin rendo brake system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Okazaki, Y; Itabashi, T; Shinohara, S; Honda, Y [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

Scooters need appropriate front and rear wheel braking power distribution and each of front and rear brakes have been operated using right and left levers. This time, a low cost brakes with cable type combined brake system for small size scooter and a brakes with hydraulic type combined brake system for middle size scooter have been developed to obtain appropriate front and rear wheel braking power distribution. Both systems use convenient left lever to operate. 3 refs., 9 figs., 1 tab.

Multivariate research in areas of phosphorus cast-iron brake shoes manufacturing using the statistical analysis and the multiple regression equations

Science.gov (United States)

Kiss, I.; Cioată, V. G.; Alexa, V.; Raţiu, S. A.

2017-05-01

The braking system is one of the most important and complex subsystems of railway vehicles, especially when it comes for safety. Therefore, installing efficient safe brakes on the modern railway vehicles is essential. Nowadays is devoted attention to solving problems connected with using high performance brake materials and its impact on thermal and mechanical loading of railway wheels. The main factor that influences the selection of a friction material for railway applications is the performance criterion, due to the interaction between the brake block and the wheel produce complex thermos-mechanical phenomena. In this work, the investigated subjects are the cast-iron brake shoes, which are still widely used on freight wagons. Therefore, the cast-iron brake shoes - with lamellar graphite and with a high content of phosphorus (0.8-1.1%) - need a special investigation. In order to establish the optimal condition for the cast-iron brake shoes we proposed a mathematical modelling study by using the statistical analysis and multiple regression equations. Multivariate research is important in areas of cast-iron brake shoes manufacturing, because many variables interact with each other simultaneously. Multivariate visualization comes to the fore when researchers have difficulties in comprehending many dimensions at one time. Technological data (hardness and chemical composition) obtained from cast-iron brake shoes were used for this purpose. In order to settle the multiple correlation between the hardness of the cast-iron brake shoes, and the chemical compositions elements several model of regression equation types has been proposed. Because a three-dimensional surface with variables on three axes is a common way to illustrate multivariate data, in which the maximum and minimum values are easily highlighted, we plotted graphical representation of the regression equations in order to explain interaction of the variables and locate the optimal level of each variable for

Rail Brake System Using a Linear Induction Motor for Dynamic Braking

Science.gov (United States)

Sakamoto, Yasuaki; Kashiwagi, Takayuki; Tanaka, Minoru; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

One type of braking system for railway vehicles is the eddy current brake. Because this type of brake has the problem of rail heating, it has not been used for practical applications in Japan. Therefore, we proposed the use of a linear induction motor (LIM) for dynamic braking in eddy current brake systems. The LIM reduces rail heating and uses an inverter for self excitation. In this paper, we estimated the performance of an LIM from experimental results of a fundamental test machine and confirmed that the LIM generates an approximately constant braking force under constant current excitation. At relatively low frequencies, this braking force remains unaffected by frequency changes. The reduction ratio of rail heating is also approximately proportional to the frequency. We also confirmed that dynamic braking resulting in no electrical output can be used for drive control of the LIM. These characteristics are convenient for the realization of the LIM rail brake system.

The role of looming and attention capture in drivers' braking responses.

Science.gov (United States)

Terry, Hugh R; Charlton, Samuel G; Perrone, John A

2008-07-01

This study assessed the ability of drivers to detect the deceleration of a preceding vehicle in a simulated vehicle-following task. The size of the preceding vehicles (car, van, or truck) and following speeds (50, 70, or 100 km/h) were systematically varied. Participants selected a preferred following distance by engaging their vehicle's cruise control and when the preceding vehicle began decelerating (no brake lights were illuminated), the participant's braking latency and distances to the lead vehicle were recorded. The experiment also employed a secondary task condition to examine how the attention-capturing properties of a looming vehicle were affected by driver distraction. The results indicated that a looming stimulus is capable of redirecting a driver's attention in a vehicle following task and, as with detection of brake lights, a driver's detection of a looming vehicle is compromised in the presence of a distracting task. Interestingly, increases in vehicle size had the effect of decreasing drivers' braking latencies and drivers engaged in the secondary task were significantly closer to the lead vehicle when they began braking, regardless of the size of the leading vehicle. Performance decrements resulting from the secondary task were reflected in a time-to-collision measure but not in optic expansion rate, lending support to earlier arguments that time-to-collision estimates require explicit cognitive judgements while perception of optic expansion may function in a more automatic fashion to redirect a driver's attention when cognitive resources are low or collision is imminent.

Cooperative Control of Regenerative Braking and Antilock Braking for a Hybrid Electric Vehicle

Directory of Open Access Journals (Sweden)

Guodong Yin

2013-01-01

Full Text Available A new cooperative braking control strategy (CBCS is proposed for a parallel hybrid electric vehicle (HEV with both a regenerative braking system and an antilock braking system (ABS to achieve improved braking performance and energy regeneration. The braking system of the vehicle is based on a new method of HEV braking torque distribution that makes the antilock braking system work together with the regenerative braking system harmoniously. In the cooperative braking control strategy, a sliding mode controller (SMC for ABS is designed to maintain the wheel slip within an optimal range by adjusting the hydraulic braking torque continuously; to reduce the chattering in SMC, a boundary-layer method with moderate tuning of a saturation function is also investigated; based on the wheel slip ratio, battery state of charge (SOC, and the motor speed, a fuzzy logic control strategy (FLC is applied to adjust the regenerative braking torque dynamically. In order to evaluate the performance of the cooperative braking control strategy, the braking system model of a hybrid electric vehicle is built in MATLAB/SIMULINK. It is found from the simulation that the cooperative braking control strategy suggested in this paper provides satisfactory braking performance, passenger comfort, and high regenerative efficiency.

Trends in passenger transport and freight energy use in Spain

International Nuclear Information System (INIS)

Mendiluce, Maria; Schipper, Lee

2011-01-01

This paper provides for the first time a complete analysis of recent trends in activity, carbon emissions, modal shares, energy intensities, vehicle use and fuels in the Spanish transport system from 1990 to 2008 and discusses policy options. Passenger and freight activities have increased in Spain and are projected to continue, presenting a challenge for sustainable mobility efforts; emissions have increased, mainly fueled by the rise in activity; modal shares have pulled away from public transport, with a decrease in bus and rail, towards an increase in car and air travel; energy intensities, though initially decreasing, are currently increasing; and fuel use has taken over 37% of Spanish final energy consumption. To target these issues the Spanish government has focused its efforts in targeting energy efficiency through dieselization, which has not led to positive results. More recently policies and measures have been directed towards redirecting modal shares and diversifying the fuel mix. Little has been done to reduce activity besides some anecdotic public awareness campaigns. Activity reduction may be achieved with regulations, restrictions and mobility plans; by increasing high speed rail and rail freight transport; by improving intermodality and tying the Spanish rail network with the EU; and with more urban transport planning at local level. - Highlights: → Complete analysis of recent trends in Spanish transport system from 1990 to 2008. → Passenger and freight activities have driven GHG emissions increase. → Modal shares have pulled away from public transport. → Policy efforts targeted energy efficiency and redirecting modal shares and diversifying the fuel mix. → Little has been done to reduce activity.

THE STUDY OF BRAKE EFFECTIVENESS HOPPER SYSTEM WITH SEPARATE BRAKING TRUCKS

Directory of Open Access Journals (Sweden)

O. Je. Nishhenko

2009-06-01

Full Text Available The results of tests of the hopper brake systems for the pellets having typical system and separate braking per each bogie are presented. It is shown that the brake system with separate braking has several advantages as compared to the typical one.

Developing of a software for determining advanced brake failures in brakes test bench

Directory of Open Access Journals (Sweden)

Hakan Köylü

2016-08-01

Full Text Available At present time, the brake test bench conducts the braking and suspension tests of front or rear axles and the test results are evaluated through one axle. The purpose of the brake testing system is to determine braking force and damping coefficient dissymmetry of one axle. Thus, this test system evaluates the performance of service brake, hand brake and suspension systems by considering separately front and rear axle dissymmetry. For this reason, the effects of different braking and damping forces applied by right and left wheels of both axles on braking performance of all vehicle are not determined due to available algorithm of the test bench. Also, the other brake failures are not occurred due to the algorithm of brake test system. In this study, the interface has been developed to determine the other effects of dissymmetry and the other brake failures by using the one axle results of brake test bench. The interface has algorithm computing the parameters according to the interaction between front and rear axles by only using measured test results. Also, it gives the warnings by comparing changes in the parameters with braking performance rules. Braking and suspension tests of three different vehicles have been conducted by using brake test bench to determine the performance of the algorithm. Parameters based on the axle interaction have been calculated by transferring brake test results to the interface and the test results have been evaluated. As a result, the effects of brake and suspension failures on braking performance of both axle and vehicle have been determined thanks to the developed interface.

Evaluation of an autonomous braking system in real-world PTW crashes.

Science.gov (United States)

Savino, Giovanni; Pierini, Marco; Rizzi, Matteo; Frampton, Richard

2013-01-01

Powered 2-wheelers (PTWs) are becoming increasingly popular in Europe. They have the ability to get around traffic queues, thus lowering fuel consumption and increasing mobility. The risk of rider injury in a traffic crash is however much higher than that associated with car users. The European project, Powered Two Wheeler Integrated Safety (PISa), identified an autonomous braking system (AB) as a priority to reduce the injury consequences of a PTW crash. The aim of this study was to assess the potential effectiveness of the AB system developed in PISa, taking into account the specific system characteristics that emerged during the design, development and testing phases. Fifty-eight PTW cases representing European crash configurations were examined, in which 43 percent of riders sustained a Maximum Abbreviated Injury Scale (MAIS) 2+ injury. Two of the most common crash types were a PTW impacting a stationary object (car following scenario) 16% and an object pulling across the PTW path (crossing scenario) 54%. An expert team analysed the in-depth material of the sample crashes and determined a posteriori to what extent the AB would have affected the crash. For those cases where the AB was evaluated as applicable, a further quantitative evaluation of the benefits was conducted by considering a set of different possible rider reactions in addition to that exhibited in the actual crash. In 67 percent of cases, the application of AB could have mitigated the crash outcome. Analysis of those real crash cases showed the potential for an expert rider to avoid the collision. An early reaction of the rider, associated with a correct application of the brakes would have avoided 18 of the 37 car following/crossing scenarios. Conversely, according to the analysis, an expert rider would not have been able to avoid 19 of the 37 cases. In 14 of those 19 cases, the AB would have contributed to mitigating the crash outcome. This study demonstrated significant potential for

Development of mechanical brake assist; Mechanical brake assist no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Konishi, M; Shingyoji, S; Nakamura, I; Tagawa, T; Saito, Y; Ishihara, T; Kobayashi, S; Yoshida, M [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

We have recognized that there are drivers who cannot apply strong brake pedal force , in spite of the necessity of hard braking in emergencies. We have developed a `mechanical brake assist system` which assists drivers appropriately, according to the drivers` characteristics based on studying the characteristic`s of conditions of drivers applying the brake pedal force in emergency conditions. 2 refs., 7 figs., 1 tab.

International Passenger and Freight Report

Data.gov (United States)

Department of Transportation — The International Passenger and Freight report is a summarization of all passengers and all freight transported between the U.S. and foreign countries combined, with...

Magnetostrictive Brake

Science.gov (United States)

Diftler, Myron A.; Hulse, Aaron

2010-01-01

A magnetostrictive brake has been designed as a more energy-efficient alternative to a magnetic fail-safe brake in a robot. (In the specific application, failsafe signifies that the brake is normally engaged; that is, power must be supplied to allow free rotation.) The magnetic failsafe brake must be supplied with about 8 W of electric power to initiate and maintain disengagement. In contrast, the magnetostrictive brake, which would have about the same dimensions and the same torque rating as those of the magnetic fail-safe brake, would demand only about 2 W of power for disengagement. The brake (see figure) would include a stationary base plate and a hub mounted on the base plate. Two solenoid assemblies would be mounted in diametrically opposed recesses in the hub. The cores of the solenoids would be made of the magnetostrictive alloy Terfenol-D or equivalent. The rotating part of the brake would be a ring-and spring- disk subassembly. By means of leaf springs not shown in the figure, this subassembly would be coupled with the shaft that the brake is meant to restrain. With no power supplied to the solenoids, a permanent magnet would pull axially on a stepped disk and on a shelf in the hub, causing the ring to be squeezed axially between the stepped disk and the hub. The friction associated with this axial squeeze would effect the braking action. Supplying electric power to the solenoids would cause the magnetostrictive cylinders to push radially inward against a set of wedges that would be in axial contact with the stepped disk. The wedges would convert the radial magnetostrictive strain to a multiplied axial displacement of the stepped disk. This axial displacement would be just large enough to lift the stepped disk, against the permanent magnetic force, out of contact with the ring. The ring would then be free to turn because it would no longer be squeezed axially between the stepped disk and the hub.

Study of Freight Transport Trip Chains

DEFF Research Database (Denmark)

Jørgensen, Kaj

1999-01-01

Investigation of energy use and emissions (CO2, NOx, THC, CO, SO2, PM) of freight trains and lorries. The report documents the establishment of energy and emission factors, and in particularly the issue of energy use of freight train is treated in detail.......Investigation of energy use and emissions (CO2, NOx, THC, CO, SO2, PM) of freight trains and lorries. The report documents the establishment of energy and emission factors, and in particularly the issue of energy use of freight train is treated in detail....

Comparison of Regenerative Braking Efficiencies of MY2012 and MY2013 Nissan Leaf

Directory of Open Access Journals (Sweden)

Albert Boretti

2016-07-01

Full Text Available The use of kinetic energy recovery systems (KERS is the best solution presently available to dramatically improve the energy economy of passenger cars. The paper presents an experimental analysis of the energy flow to and from the battery of a MY 2012 and a MY 2013 Nissan Leaf covering the Urban Dynamometer Driving Schedule (UDDS. The two vehicles differ for the integration of the electric drivetrain component, plus a different use of the electric motor and the regenerative brakes, in addition to a different weight. It is shown that while the efficiency propulsive power to vehicle / power from battery are basically unchanged, at about 87-89 %, the efficiency power to the battery / braking power to vehicle are significantly improved from values of about 70-80 % to values of 72-87 %. The analysis provides a state-of-the-art benchmark of the propulsion and regenerative braking efficiencies of electric vehicles.

Brake Performance Analysis of ABS for Eddy Current and Electrohydraulic Hybrid Brake System

Directory of Open Access Journals (Sweden)

Ren He

2013-01-01

Full Text Available This paper introduces an eddy current and electro-hydraulic hybrid brake system to solve problems such as wear, thermal failure, and slow response of traditional vehicle brake system. Mathematical model was built to calculate the torque of the eddy current brake system and hydraulic brake system and analyze the braking force distribution between two types of brake systems. A fuzzy controller on personal computer based on LabVIEW and Matlab was designed and a set of hardware in the loop system was constructed to validate and analyze the performance of the hybrid brake system. Through lots of experiments on dry and wet asphalt roads, the hybrid brake system achieves perfect performance on the experimental bench, the hybrid system reduces abrasion and temperature of the brake disk, response speed is enhanced obviously, fuzzy controller keeps high utilization coefficient due to the optimal slip ratio regulation, and the total brake time has a smaller decrease than traditional hydraulic brake system.

Influence of impact speed on head and brain injury outcome in vulnerable road user impacts to the car hood.

Science.gov (United States)

Fredriksson, Rikard; Zhang, Liying; Boström, Ola; Yang, King

2007-10-01

EuroNCAP and regulations in Europe and Japan evaluate the pedestrian protection performance of cars. The test methods are similar and they all have requirements for the passive protection of the hood area at a pedestrian to car impact speed of 40 km/h. In Europe, a proposal for a second phase of the regulation mandates a brake-assist system along with passive requirements. The system assists the driver in optimizing the braking performance during panic braking, resulting in activation only when the driver brakes sufficiently. In a European study this was estimated to occur in about 50% of pedestrian accidents. A future system for brake assistance will likely include automatic braking, in response to a pre-crash sensor, to avoid or mitigate injuries of vulnerable road users. An important question is whether these systems will provide sufficient protection, or if a parallel, passive pedestrian protection system will be necessary. This study investigated the influence of impact speed on head and brain injury risk, in impacts to the carhood. One car model was chosen and a rigid adjustable plate was mounted under the hood. Free-flying headform impacts were carried out at 20 and 30 km/h head impact velocities at different under-hood distances, 20 to 100 mm; and were compared to earlier tests at 40 km/h. The EEVC WG17 adult pedestrian headform was used for non-rotating tests and a Hybrid III adult 50th percentile head was used for rotational tests where linear and rotational acceleration was measured. Data from the rotational tests was used as input to a validated finite element model of the human head, the Wayne State University Head Injury Model (WSUHIM). The model was utilized to assess brain injury risk and potential injury mechanism in a pedestrian-hood impact. Although this study showed that it was not necessarily true that a lower HIC value reduced the risk for brain injury, it appeared, for the tested car model, under-hood distances of 60 mm in 20 km/h and 80 mm

Participation for Sustainable Urban Freight Transport Systems : A Case Study of Freight Receivers in the City of Gothenburg

OpenAIRE

Lindkvist, Hannes

2017-01-01

This thesis is a case study research that look into the difficulty in engaging freight receivers in initiatives related to urban freight transport. The aim of the paper is to investigate how participatory processes could be formed for more successful outcomes and how the freight receivers could become more engaged in the processes. By conducting a qualitative research where primarily interviews with freight receivers and other concerned stakeholder were made, it was possible to distinguish di...

Effects of uncertainty, transmission type, driver age and gender on brake reaction and movement time.

Science.gov (United States)

Warshawsky-Livne, Lora; Shinar, David

2002-01-01

Braking time (BT) is a critical component in safe driving, and various approaches have been applied to minimize it. This study analyzed the components of BT in order to assess the effects of age, gender, vehicle transmission type, and event uncertainty, on its two primary components, perception-reaction time and brake-movement time. Perception-reaction time and brake-movement time were measured at the onset of lights for 72 subjects in a simulator. The six experimental conditions were three levels of uncertainty conditions (none, some, and some + false alarms) and two types of transmission (manual and automatic). The 72 subjects, half male and half female, were further divided into three age groups (mean of 23, 30, and 62 years). Each subject had 10 trials in each of the three levels of uncertainty conditions. Transmission type did not significantly affect either perception-reaction time or brake-movement time. Perception-reaction time increased significantly from 0.32 to 0.42 s (P brake-movement time did not change. Perception-reaction time increased (from 0.35 to 0.43 s) with age but brake-movement time did not change with age. Gender did not affect perception-reaction time but did affect brake-movement time (males 0.19 s vs. females 0.16 s). At 90 km/h, a car travels 0.25 m in 0.01 s. Consequently, even such small effects multiplied by millions of vehicle-kilometers can contribute to significant savings in lives and damages.

Electronic brakes. From ABS to brake-by-wire. 2. ed.; Elektronische Bremssysteme. Vom ABS zum Brake-by-Wire

Energy Technology Data Exchange (ETDEWEB)

Reichel, H.R.

2003-07-01

The book reports trends in vehicle brakes from 1968 to 1998. This was the age of the electronic revolution. The book presents conventional brakes, antiblocking systems (ABS), antislip systems (ASS), brake assistants (BAS), dynamic control systems, and brake-by-wire systems. [German] Das Buch berichtet ueber Entwicklungen an Fahrzeugbremsanlagen in der Zeitspanne von 1968 bis etwa 1998. Diese Zeit war gepraegt vom Vordringen der Elektronik in die Bremsen, was fuer Hersteller und Kunden eine Revolution bedeutete. Behandelt sind: (a) Konventionelle Bremsanlagen, (b) Antiblockiersysteme (ABS), (c) Anti-Schlupf-regelungen (ASR), (d) Bremsassistenten (BAS), (e) Fahrdynamikregelungen (FDR, ESP), (f) Brake-by-Wire (orig.)

Disk brake design for cooling improvement using Computational Fluid Dynamics (CFD)

International Nuclear Information System (INIS)

Munisamy, Kannan M; Shafik, Ramel

2013-01-01

The car disk brake design is improved with two different blade designs compared to the baseline blade design. The two designs were simulated in Computational fluid dynamics (CFD) to obtain heat transfer properties such as Nusselt number and Heat transfer coefficient. The heat transfer property is compared against the baseline design. The improved shape has the highest heat transfer performance. The curved design is inferior to baseline design in heat transfer performance.

Disk brake design for cooling improvement using Computational Fluid Dynamics (CFD)

Science.gov (United States)

Munisamy, Kannan M.; Shafik, Ramel

2013-06-01

The car disk brake design is improved with two different blade designs compared to the baseline blade design. The two designs were simulated in Computational fluid dynamics (CFD) to obtain heat transfer properties such as Nusselt number and Heat transfer coefficient. The heat transfer property is compared against the baseline design. The improved shape has the highest heat transfer performance. The curved design is inferior to baseline design in heat transfer performance.

Situations of car-to-pedestrian contact.

Science.gov (United States)

Matsui, Yasuhiro; Hitosugi, Masahito; Takahashi, Kunio; Doi, Tsutomu

2013-01-01

To reduce the severity of injuries and the number of pedestrian deaths in traffic accidents, active safety devices providing pedestrian detection are considered effective countermeasures. The features of car-to-pedestrian collisions need to be known in detail to develop such safety devices. Because information on real-world accidents is limited, this study investigated near-miss situations captured by drive recorders installed in passenger cars. We showed similarities of the contact situation between near-miss incidents and real-world fatal pedestrian accidents in Japan. We analyzed the near-miss incident data via video capturing pedestrians crossing the road in front of forward-moving cars. Using a video frame captured by a drive recorder, the time to collision (TTC) was calculated from the car velocity and the distance between the car and pedestrian at the moment that the pedestrian initially appeared. The average TTC in the cases where pedestrians were not using a pedestrian crossing was shorter than that in the cases where pedestrians were using a pedestrian crossing. The average TTC in the cases where pedestrians emerged from behind obstructions was shorter than that in the cases where drivers had unobstructed views of the pedestrians. We propose that the specifications of the safety device for pedestrian detection and automatic braking should reflect the severe approach situation for a pedestrian and car including the TTC observed for near-miss incidents.

Validity of a device designed to measure braking power in bicycle disc brakes.

Science.gov (United States)

Miller, Matthew C; Fink, Philip W; Macdermid, Paul William; Perry, Blake G; Stannard, Stephen R

2017-07-21

Real-world cycling performance depends not only on exercise capacities, but also on efficiently traversing the bicycle through the terrain. The aim of this study was to determine if it was possible to quantify the braking done by a cyclist in the field. One cyclist performed 408 braking trials (348 on a flat road; 60 on a flat dirt path) over 5 days on a bicycle fitted with brake torque and angular velocity sensors to measure brake power. Based on Newtonian physics, the sum of brake work, aerodynamic drag and rolling resistance was compared with the change in kinetic energy in each braking event. Strong linear relationships between the total energy removed from the bicycle-rider system through braking and the change in kinetic energy were observed on the tar-sealed road (r 2  = 0.989; p brake torque and angular velocity sensors are valid for calculating brake power on the disc brakes of a bicycle in field conditions. Such a device may be useful for investigating cyclists' ability to traverse through various terrains.

Brake Performance Analysis of ABS for Eddy Current and Electrohydraulic Hybrid Brake System

OpenAIRE

Ren He; Xuejun Liu; Cunxiang Liu

2013-01-01

This paper introduces an eddy current and electro-hydraulic hybrid brake system to solve problems such as wear, thermal failure, and slow response of traditional vehicle brake system. Mathematical model was built to calculate the torque of the eddy current brake system and hydraulic brake system and analyze the braking force distribution between two types of brake systems. A fuzzy controller on personal computer based on LabVIEW and Matlab was designed and a set of hardware in the loop system...

Hardware simulation of automatic braking system based on fuzzy logic control

Directory of Open Access Journals (Sweden)

Noor Cholis Basjaruddin

2016-07-01

Full Text Available In certain situations, a moving or stationary object can be a barrier for a vehicle. People and vehicles crossing could potentially get hit by a vehicle. Objects around roads as sidewalks, road separator, power poles, and railroad gates are also a potential source of danger when the driver is inattentive in driving the vehicle. A device that can help the driver to brake automatically is known as Automatic Braking System (ABS. ABS is a part of the Advanced Driver Assistance Systems (ADAS, which is a device designed to assist the driver in driving the process. This device was developed to reduce human error that is a major cause of traffic accidents. This paper presents the design of ABS based on fuzzy logic which is simulated in hardware by using a remote control car. The inputs of fuzzy logic are the speed and distance of the object in front of the vehicle, while the output of fuzzy logic is the intensity of braking. The test results on the three variations of speed: slow-speed, medium-speed, and high-speed shows that the design of ABS can work according to design.

Effects of fexofenadine and hydroxyzine on brake reaction time during car-driving with cellular phone use.

Science.gov (United States)

Tashiro, Manabu; Horikawa, Etsuo; Mochizuki, Hideki; Sakurada, Yumiko; Kato, Motohisa; Inokuchi, Takatoshi; Ridout, Fran; Hindmarch, Ian; Yanai, Kazuhiko

2005-10-01

Antihistamines are a mainstay treatment for allergic rhinitis; however, many older agents cause adverse events, including sedation and central nervous system (CNS) impairment. Research has shown sedating effects of antihistamines on driving; currently, no known study has examined whether cellular phone usage while driving further compounds impairment in individuals administered antihistamines. The aim of this study was to examine this endpoint. In a randomized, double-blind, placebo-controlled, three-way crossover study, healthy volunteers received fexofenadine HCl 120 mg, hydroxyzine HCl 30 mg and placebo. Brake reaction time (BRT) was used to examine driving performance across four conditions: driving only; driving while completing simple calculations; complex calculations; and conversing on a cellular phone. Subjective sedation assessments were also conducted. Brake reaction time with and without cellular phone usage in fexofenadine-treated subjects did not differ significantly from placebo in any condition. In contrast, hydroxyzine-treated subjects were significantly more sedated and had slower BRTs, suggesting slower hazard recognition and brake application, compared with the fexofenadine and placebo groups in all conditions. Importantly, cellular phone operation was an additive factor, increasing BRTs in hydroxyzine-treated volunteers. Fexofenadine did not impair CNS function in subjects involved in a divided attention task of driving and cellular phone operation. Copyright (c) 2005 John Wiley & Sons, Ltd.

Improved Electromagnetic Brake

Science.gov (United States)

Martin, Toby B.

2004-01-01

A proposed design for an electromagnetic brake would increase the reliability while reducing the number of parts and the weight, relative to a prior commercially available electromagnetic brake. The reductions of weight and the number of parts could also lead to a reduction of cost. A description of the commercial brake is prerequisite to a description of the proposed electromagnetic brake. The commercial brake (see upper part of figure) includes (1) a permanent magnet and an electromagnet coil on a stator and (2) a rotor that includes a steel contact plate mounted, with tension spring loading, on an aluminum hub. The stator is mounted securely on a stationary object, which would ordinarily be the housing of a gear drive or a motor. The rotor is mounted on the shaft of the gear drive or motor. The commercial brake nominally operates in a fail-safe (in the sense of normally braking) mode: In the absence of current in the electromagnet coil, the permanent magnet pulls the contact plate, against the spring tension, into contact with the stator. To release the brake, one excites the electromagnet with a current of the magnitude and polarity chosen to cancel the magnetic flux of the permanent magnet, thereby enabling the spring tension to pull the contact plate out of contact with the stator. The fail-safe operation of the commercial brake depends on careful mounting of the rotor in relation to the stator. The rotor/stator gap must be set with a tolerance between 10 and 15 mils (between about 0.25 and about 0.38 mm). If the gap or the contact pad is thicker than the maximum allowable value, then the permanent magnetic field will not be strong enough to pull the steel plate across the gap. (For this reason, any contact pad between the contact plate and the stator must also be correspondingly thin.) If the gap exceeds the maximum allowable value because of shaft end play, it becomes impossible to set the brake by turning off the electromagnet current. Although it may

White papers on freight efficiency.

Science.gov (United States)

2016-05-31

A number of stakeholders met with the ultimate goal of identifying inefficiencies faced by the freight system and putting forward a set of : strategies to achieve a more efficient freight system. In doing so, a key first step was to provide insight a...

DETERMINATION OF THE ISSUE CONCERNING THE LIFT RESISTANCE FACTOR OF LIGHTWEIGHT CAR

Directory of Open Access Journals (Sweden)

A. O. Shvets

2015-10-01

Full Text Available Purpose. The analytical study of the connection between the longitudinal force, acting on the light-weight car, lateral and vertical forces of interaction in the contact zone «wheel – rail» with the lift resistance factor value is to provide a simple relationships between them. Methodology. Research was conducted by the method of mathematical modeling of loading the freight car when driving at different speeds on straight and curved sections of a track. Findings. Even in the absence of «lift» accordingly the classical train stability theory, as the hinge-rod system, the presence of the longitudinal compressive forces may become a factor provoking cars derailment. The main reason of wheel climbing on rails is the combination of processes of dynamic interaction between the hunting vehicle and the track with simultaneous action of longitudinal compressive forces, and not the destabilization of train as a hingedrod system. To assess the impact of the longitudinal forces value on the lift resistance factor there are presented the calculation results for the empty gondola car motion, model No. 12-532, on 250 m radius curve with 150 mm rise and cross starting of car underframe relating to the track axis in 50 mm guiding section. The calculations were made in such a curve excluding the inertial forces from outstanding acceleration and taking into account the unbalanced acceleration with the permissible speed of 65 km/h. Originality. This study provides the technique of determining the lift resistance factor by longitudinal forces, which is somewhat different from the standard one, as well as evaluates impact of rolling stock speed on this factor. Practical value. The authors clarify the current method of determining the lift resistance factor by longitudinal forces and assess the impact of rolling stock speed on the value of this factor. From these studies one can conclude that because of cars hunting their lift is possible even when the train as

Connected Car: Quantified Self becomes Quantified Car

Directory of Open Access Journals (Sweden)

Melanie Swan

2015-02-01

Full Text Available The automotive industry could be facing a situation of profound change and opportunity in the coming decades. There are a number of influencing factors such as increasing urban and aging populations, self-driving cars, 3D parts printing, energy innovation, and new models of transportation service delivery (Zipcar, Uber. The connected car means that vehicles are now part of the connected world, continuously Internet-connected, generating and transmitting data, which on the one hand can be helpfully integrated into applications, like real-time traffic alerts broadcast to smartwatches, but also raises security and privacy concerns. This paper explores the automotive connected world, and describes five killer QS (Quantified Self-auto sensor applications that link quantified-self sensors (sensors that measure the personal biometrics of individuals like heart rate and automotive sensors (sensors that measure driver and passenger biometrics or quantitative automotive performance metrics like speed and braking activity. The applications are fatigue detection, real-time assistance for parking and accidents, anger management and stress reduction, keyless authentication and digital identity verification, and DIY diagnostics. These kinds of applications help to demonstrate the benefit of connected world data streams in the automotive industry and beyond where, more fundamentally for human progress, the automation of both physical and now cognitive tasks is underway.

The North American Transborder Freight Database

Data.gov (United States)

Department of Transportation — The North American Transborder Freight Database, available since April 1993, contains freight flow data by commodity type and by mode of transportation (rail, truck,...

Study on Differential Regenerative Braking Torque Control to Increase the Stability of the Small Electric Vehicle with Four In-Wheel Motors

Directory of Open Access Journals (Sweden)

Ali N. M.

2017-01-01

Full Text Available Based on the advantages of the electric motor such as fast and precise torque response, the performance of the electric vehicle (EV can be improved. During braking or driving on the cornering, the vehicle will over steer or under steer if a car turns by more or less than the amount commanded by the driver. To improve the stability of the small EV with four in-wheel motors, the differential regenerative braking torque control is proposed. In this system, the regenerative braking torque at each wheel will be controlled individually based on the value of slip ratio. If the slip ratio is greater than the optimum value, the regenerative brake will turn off. In this situation, the electric motor will not produce the regenerative braking torque. Conversely, if the slip ratio lower than the optimum value, the regenerative brake will turn on and the electric motor will generate the regenerative braking torque. In the numerical analysis, to investigate the effectiveness of the proposed model, the road condition is set to an icy road on the left tire and dry asphalt on the right tire. From the simulation results, the differential regenerative braking torque control can prevent the tire from lock-up and avoid the vehicle from skidding.

Analysis of the interaction of participants freight forwarding system

Directory of Open Access Journals (Sweden)

Pavlo Popovych

2016-12-01

Full Text Available Main goal of this work is the analysis of the interaction of participants of freight forwarding activities. Research methods included analysis of scientific literature, theory of systems and systems analysis, methods of induction and deduction. As sources of information used and applied work of fundamental importance known foreign and local scientists and regulatory and legislative documents of Ukraine for the state transport policy. In the article the basic interactions of participants of freight forwarding activities. Classified components freight forwarding services. Assign the concept freight forwarding system and its aim. Established element and forms of cooperation in the freight forwarding system. The main task of forwarding companies are organizing, coordinating and ensuring the delivery from shipper to consignee. Freight forwarding company responsible for the timely delivery of the goods on the condition of preservation of the quantity and quality specified time conditions. Currently used methods are uneffective decision-making, leading to losses. These circumstances require improvement methodology management of freight forwarding companies. This is possible only using modern mathematical methods and information technologies that will improve the operation of freight forwarding companies. The article presents a theoretical exposition of the basic processes of interaction between participants in freight forwarding system. The article may be of interest to specialists of freight forwarding companies.

Freight transport in towns. [Denmark]. Godstransport i byer; Hovedrapport

Energy Technology Data Exchange (ETDEWEB)

1992-10-01

The aim was to evaluate a number of possibilities for reducing energy consumption and thus air pollution caused by freight transport in urban areas. The Danish towns of Vejle and Roskilde were taken as examples and the two towns were compared with regard to the town plan, use of land area, the road network, amount of traffic and commercial structure. Economical aspects and the most important initiatives for improvements, including a decrease in traffic accidents, are discussed. These initiatives are coordination of transportation by firms, more drivers using the same vehicles, less frequent deliveries, optimazation of route planning, car sharing, special routes for lorries, traffic and speed control, better siting of new transport functions, re-siting of firms dependent on freight transport, the use of smaller vehicles where possible, no transport of people in trucks or vans, less use of bicycles for transporting messages, more use of underground pipes for transport of materials, lifting equipment for smaller vans and trucks, lifting equipment that is more flexible, motors turned off when loading and loading, reduction of emballage volume, and a more careful way of driving which can help to reduce energy consumption. A computer programme was constructed in order to calculate energy consumption in these relations, emission of hydrocarbons, carbon monoxide, nitrogen oxides and particles, transportation costs and number of traffic accidents. Results are presented in detail and discussed. (AB) (78 refs.).

Influence of convective cooling on a disc brake temperature distribution during repetitive braking

International Nuclear Information System (INIS)

Adamowicz, Adam; Grzes, Piotr

2011-01-01

The purpose of this study is to evaluate an impact of convective mode of heat transfer on the thermal behaviour of a disc brake system during repetitive braking process with the constant velocity using fully three-dimensional finite element model. The transient thermal analysis to determine the temperature distributions on the contact surface of a disc brake is performed. The issue of non-uniform frictional heating effects of mutual slipping of a disc over fixed pads is tested using FE models with the several possible to occur in automotive application heat transfer coefficients. To have a possibility of comparison of the temperature distributions of a disc during cyclic brake application, the energy transformed during time of every analyzed case of braking process and the subsequent release periods was equal. The time-stepping procedure is employed to develop moving heat source as the boundary heat flux acting interchangeably with the convective cooling terms. The difficulties accounted for the accurate simulation of heating during spin of the rotor is omitted by the use of the code, which enable shaping curves responsible for the thermal flux entering the disc at subsequent moments of time. The resulting evolution of temperature on the friction surface reveals a wide range of variations, distinguishing periods of heating and cooling states. It has been established, that during single braking the convective cooling has insignificant influence on the temperature distributions of a disc brake, consequently is not able to prevent overheat problem. However the brake release period after the braking operation, when the velocity of the vehicle remains on the same level, results in considerable decrease of temperature. - Highlights: → Convection does not allow to lower temperature of disc during single braking process. → Maximal temperature of disc decreases with number of brake applications. → Temperature at the end of braking increases with number of brake

Emergency braking : research summary.

NARCIS (Netherlands)

Schlösser, L.H.M.

1976-01-01

This report deals with an investigation concerning braking capacity of trucks if somewhere a failure occurs in the normal service brake. Purpose of research was to get an insight in various secondary braking systems for trucks. It is shown that with almost all of the secondary braking system it was

Roller Locking Brake

Science.gov (United States)

Vranish, John M.

1993-01-01

Roller locking brake is normally braking rotary mechanism allowing free rotation when electromagnet in mechanism energized. Well suited to robots and other machinery which automatic braking upon removal of electrical power required. More compact and reliable. Requires little electrical power to maintain free rotation and exhibits minimal buildup of heat.

Energy Consumption and Freight Transport Demand in Denmark

DEFF Research Database (Denmark)

Salling, Kim Bang; Bonilla, David

2008-01-01

Considering the externalities of freight transport activity (energy use, accidents, congestion, its related GHG emissions, and lost oil revenues) this article reviews trends from 1990-2005 in truck freight fuel intensity (energy use per tonne-km moved), on road truck fuel economy (L/ 100 km driven......). We review changes in decoupling truck freight activity from GDP. We examine separately five manufacturing sectors using data from Statistics Denmark on vehicle performance for 1980-2006. Our four major findings are: (1) truck freight energy intensity (mj/tonne-km) continues to grow as well as CO2...... emissions; (2) decoupling has not been large enough to reduce overall energy use of truck; (3) because of the absence of fuel economy regulations, a low average vehicle load, increased hauling distance, overall energy use of truck freight will continue to expand; (4) results show that standard freight...

Concept of Seikan car train; Yuro tunnel ni manabu Seikan car train koso (rail ni doroteki kino wo)

Energy Technology Data Exchange (ETDEWEB)

Hirama, H.

1997-08-15

This paper summarizes an idea of operating a car train in the Seikan tunnel. Advantages expected from realization of this idea include assurance of mass transportation, enhancement in safety, reduction of transportation time, completion of a nationwide traffic network, and reduction of the transportation cost. A total traffic amount as sought from quantity of cargoes and number of passengers is estimated to be about 400 cars a day, and the number of trains to be operated assuming a car loading rate at 50% would be 28 trains a day. According to the profitability of this operation derived by using as calculation bases the fare revenue, expenditures and depreciation, the operation would turn into black ink in five years, clearing cumulative deficits in 17 years. In order to realize this operation, it is a prerequisite that the regulation on limitation of vehicle size (maximum width and height of vehicles) be mitigated as lax as in Eurotunnel. In addition, introduction of self-running freight cars and improvement of access roads will be necessary. Estimated economic effects may include time saving profit of 500 million yen annually, tax revenue effect of 200 million yen annually, and production inducing effect of 1.9 billion yen annually. Other expected effects may include employment effect, improvement in information transmitting function, and acceleration of different projects. 3 figs., 1 tab.

Sprag solenoid brake. [development and operations of electrically controlled brake

Science.gov (United States)

Dane, D. H. (Inventor)

1974-01-01

The development and characteristics of an electrically operated brake are discussed. The action of the brake depends on energizing a solenoid which causes internally spaced sprockets to contact the inner surface of the housing. A spring forces the control member to move to the braking position when the electrical function is interrupted. A diagram of the device is provided and detailed operating principles are explained.

An antilock molecular braking system.

Science.gov (United States)

Sun, Wei-Ting; Huang, Shou-Ling; Yao, Hsuan-Hsiao; Chen, I-Chia; Lin, Ying-Chih; Yang, Jye-Shane

2012-08-17

A light-driven molecular brake displaying an antilock function is constructed by introducing a nonradiative photoinduced electron transfer (PET) decay channel to compete with the trans (brake-off) → cis (brake-on) photoisomerization. A fast release of the brake can be achieved by deactivating the PET process through addition of protons. The cycle of irradiation-protonation-irradiation-deprotonation conducts the brake function and mimics the antilock braking system (ABS) of vehicles.

Injuries resulting from car surfing--United States, 1990-2008.

Science.gov (United States)

2008-10-17

"Car surfing" is a term introduced in the mid-1980s to describe a thrill-seeking activity that involves riding on the exterior of a moving motor vehicle while it is being driven by another person. Although reports of car-surfing injuries have been published in the United States, no study to date has analyzed these events from a national perspective. Because traditional public health datasets do not collect morbidity or mortality data on this practice, CDC searched U.S. newspaper reports to provide an initial characterization of car-surfing injuries on a national scale. That analysis identified 58 reports of car-surfing deaths and 41 reports of nonfatal injury from 1990 through August 2008. Most reports of car-surfing injuries came from newspapers in the Midwest and South (75%), and most of the injuries were among males (70%) and persons aged 15-19 years (69%). The first identified newspaper reports about car-surfing injuries were published in the early 1990s, and new reports have been published every year since then. Parents and teens should be aware of the potentially lethal consequences of car surfing, which can occur even at low vehicle speeds, sometimes resulting from unanticipated movements of the vehicle, such as swerving or braking.

Automatic Parking of Self-Driving CAR Based on LIDAR

Science.gov (United States)

Lee, B.; Wei, Y.; Guo, I. Y.

2017-09-01

To overcome the deficiency of ultrasonic sensor and camera, this paper proposed a method of autonomous parking based on the self-driving car, using HDL-32E LiDAR. First the 3-D point cloud data was preprocessed. Then we calculated the minimum size of parking space according to the dynamic theories of vehicle. Second the rapidly-exploring random tree algorithm (RRT) algorithm was improved in two aspects based on the moving characteristic of autonomous car. And we calculated the parking path on the basis of the vehicle's dynamics and collision constraints. Besides, we used the fuzzy logic controller to control the brake and accelerator in order to realize the stably of speed. At last the experiments were conducted in an autonomous car, and the results show that the proposed automatic parking system is feasible and effective.

AUTOMATIC PARKING OF SELF-DRIVING CAR BASED ON LIDAR

Directory of Open Access Journals (Sweden)

B. Lee

2017-09-01

Full Text Available To overcome the deficiency of ultrasonic sensor and camera, this paper proposed a method of autonomous parking based on the self-driving car, using HDL-32E LiDAR. First the 3-D point cloud data was preprocessed. Then we calculated the minimum size of parking space according to the dynamic theories of vehicle. Second the rapidly-exploring random tree algorithm (RRT algorithm was improved in two aspects based on the moving characteristic of autonomous car. And we calculated the parking path on the basis of the vehicle’s dynamics and collision constraints. Besides, we used the fuzzy logic controller to control the brake and accelerator in order to realize the stably of speed. At last the experiments were conducted in an autonomous car, and the results show that the proposed automatic parking system is feasible and effective.

Electronics and braking systems; Elektronik in Bremssystemen

Energy Technology Data Exchange (ETDEWEB)

Gaupp, W. [Rheinisch-Westfaelischer Technischer Ueberwachungs-Verein e.V., Essen (Germany). Inst. fuer Fahrzeugtechnik

2000-02-01

In addition to the anti-lock braking system ABS, which is now fitted to almost every new passenger car, an increasing number of other control systems which intervene in the vehicle's driving dynamics, such as ASR, DSC or ESP, are being introduced. This article gives an overview of such systems, from their beginnings up to the present-day, and describes future developments. (orig.) [German] Neben das Antiblockiersystem ABS, mit dem heute fast jeder neue Pkw ausgestattet ist, treten zunehmend weitere Regelsysteme, die in die Fahrdynamik des Fahrzeugs eingreifen, wie zum Beispiel ASR, DSC oder ESP. Dieser Beitrag gibt einen Ueberblick von den Anfaengen dieser Systeme bis hin zu zukuenftigen Entwicklungen. (orig.)

Brake Fundamentals. Automotive Articulation Project.

Science.gov (United States)

Cunningham, Larry; And Others

Designed for secondary and postsecondary auto mechanics programs, this curriculum guide contains learning exercises in seven areas: (1) brake fundamentals; (2) brake lines, fluid, and hoses; (3) drum brakes; (4) disc brake system and service; (5) master cylinder, power boost, and control valves; (6) parking brakes; and (7) trouble shooting. Each…

77 FR 4396 - Petition for Waiver of Compliance

Science.gov (United States)

2012-01-27

... perform and conduct required service and shop inspections, and maintain the cars in compliance with all... from the Railroad Freight Car Safety Standards, 49 CFR 215.303, which requires stenciling on restricted freight cars, for 13 freight cars. The list of these 13 cars is contained in the Exhibit A of the petition...

Reel safety brake

Science.gov (United States)

Carle, C. E. (Inventor)

1976-01-01

A braking apparatus is described for a tape transport device having two stacked coaxial reels and feelers mounted in proximity to the reels for sensing the tape being wound on each reel. A device is mounted in proximity to adjacent central hubs of the reels to a simultaneously, frictionally engage both hubs and brake both reels. A mechanical actuator is coupled to both feelers and to the brake device. The brake means comprises a pair of rubber shoulders that extend in opposite directions relative to a common axis, and turns about the axis in response to either of the feelers.

Understanding and Modeling Freight Stakeholder Behavior

Science.gov (United States)

2012-04-01

This project developed a conceptual model of private-sector freight stakeholder decisions and interactions for : forecasting freight demands in response to key policy variables. Using East Central Wisconsin as a study area, empirical : models were de...

Multimodal schedule design for synchromodal freight transport systems

NARCIS (Netherlands)

B. Behdani (Behzad); Y. Fan (Yun); B.W. Wiegmans (Bart); R.A. Zuidwijk (Rob)

2016-01-01

textabstractIntermodal freight transport has been discussed for decades as an alternative to unimodal road transport. However, it still does not represent a significant portion of the total freight market. A new and promising possibility to improve the performance of freight systems is the

Multimodal schedule design for synchromodal freight transport systems

NARCIS (Netherlands)

Behdani, Behzad; Fan, Yun; Wiegmans, Bart; Zuidwijk, Rob

2016-01-01

Intermodal freight transport has been discussed for decades as an alternative to unimodal road transport. However, it still does not represent a significant portion of the total freight market. A new and promising possibility to improve the performance of freight systems is the synchromodal

Unidirectional high gain brake stop

Science.gov (United States)

Lang, David J. (Inventor)

1987-01-01

This invention relates to a unidirectional high gain brake arrangement that includes in combination a shaft mounted for rotation within a housing. The shaft is rotatable in either direction. A brake is selectively releasably coupled to the housing and to the shaft. The brake has a first member. An intermittent motion device is respectively coupled through the first member to the housing and through a one-way clutch to the shaft. The brake also has a second member that is mechanically coupled to the first brake member and to the housing. The intermittent motion device causes the brake to be activated by movement imparted to the first brake member after a preset number of revolutions of the shaft in one direction. The brake is released by rotation of the shaft in an opposite direction whereby torque transmitted through the one-way clutch to the first brake member is removed.

Improving Urban Freight Governance and Stakeholder Management

DEFF Research Database (Denmark)

Gammelgaard, Britta; Bech Godskesen Andersen, Christina; Figueroa, Maria J.

2017-01-01

Urban freight transport is a complex field characterised by many actors and stakeholders and thus many rationalities are at stake. This paper contributes to literature on urban freight governance by approaching the field with social system theory combined with the concepts of relationship platforms...... and value co-creation. This approach facilitates an improved process to foster implementation of innovative urban freight solutions that is illustrated by means of an analysis of the Copenhagen Citylogistik-kbh demonstration project. The results of this analysis indicate that attaining a shared sense...... of value creation among stakeholders through this process is key to implementation of new urban freight solutions....

The Logistical Aspects of Freight Transportation and Forwarding

Directory of Open Access Journals (Sweden)

Zimina Anna I.

2017-04-01

Full Text Available The article substantiates the theoretical and practical aspects of freight transportation and forwarding services based on the principles of logistics. The indicators of dynamics of freight transportation in Ukraine compared to last year and the structure by types of transport have been provided. The indicators of the foreign trade performance of Ukraine have been presented, including the counter-current export and import flows, as well as the external trade balance, which directly impacts the volume and dynamics of freight transportation and forwarding services. The main parameters of the transportation and forwarding logistics system were systematized, taking into consideration the technical and operational characteristics of the rolling stock, the route of communication, and the terminals. The role and features of the functions of the inter/multimodal transportation operators – freight forwarders of the «tonnage customers» have been considered. The article determines principles for the organization of work of freight forwarders, as well as the terms of agreement of the parties when the freight forwarding contract is concluded. The conditions for developing a logistics approach to the implementation of freight transportation and forwarding services have been generalized.

Clutches and brakes design and selection

CERN Document Server

Orthwein, William C

2004-01-01

FRICTION MATERIALSFriction CodeWearBrake FadeFriction MaterialsNotationReferencesBAND BRAKESDerivation of EquationsApplicationLever-Actuated Band Brake: Backstop DesignExample: Design of a BackstopNotationFormula CollectionReferencesEXTERNALLY AND INTERNALLY PIVOTED SHOE BRAKESPivoted External Drum BrakesPivoted Internal Drum BrakesDesign of Dual-Anchor Twin-Shoe Drum BrakesDual-Anchor Twin-Shoe Drum Brake Design ExamplesDesign of Single-Anchor Twin-Shoe Drum BrakesSingle-Anchor Twin-Shoe Drum Brake Design Exam

Deployable Brake for Spacecraft

Science.gov (United States)

Rausch, J. R.; Maloney, J. W.

1987-01-01

Aerodynamic shield that could be opened and closed proposed. Report presents concepts for deployable aerodynamic brake. Brake used by spacecraft returning from high orbit to low orbit around Earth. Spacecraft makes grazing passes through atmosphere to slow down by drag of brake. Brake flexible shield made of woven metal or ceramic withstanding high temperatures created by air friction. Stored until needed, then deployed by set of struts.

Frictional Performance and Temperature Rise of a Mining Nonasbestos Brake Material during Emergency Braking

Directory of Open Access Journals (Sweden)

Jiusheng Bao

2015-01-01

Full Text Available By simulating emergency braking conditions of mine hoisters, tribological experiments of a mining nonasbestos brake material sliding on E355CC steel friction disc investigated a pad-on-disc friction tester. It is shown that, under combined influence of braking velocity and pressure, the lubricating film and micro-convex-apices on wear surface would have complex physicochemical reactions which make the instant friction coefficient rise gradually while the instant surface temperature rises first and then falls. With the antifriction effect from lubricating film and the desquamating of composite materials, the mean friction coefficient decreases first, then rises, and decreases again with the increasing of initial braking velocity. And with the existence of micro-convex-apices and variation from increment ratio of load and actual contacting area, it rises first and then falls with the increasing of braking pressure. However, the mean surface temperature rises obviously with the increasing of both initial braking velocity and braking pressure for growth of transformed kinetic energy. It is considered that the friction coefficient cannot be considered as a constant when designing brake devices for mine hoisters. And special attention should be paid to the serious influence of surface temperature on tribological performance of brake material during emergency braking.

Braking System for Wind Turbines

Science.gov (United States)

Krysiak, J. E.; Webb, F. E.

1987-01-01

Operating turbine stopped smoothly by fail-safe mechanism. Windturbine braking systems improved by system consisting of two large steel-alloy disks mounted on high-speed shaft of gear box, and brakepad assembly mounted on bracket fastened to top of gear box. Lever arms (with brake pads) actuated by spring-powered, pneumatic cylinders connected to these arms. Springs give specific spring-loading constant and exert predetermined load onto brake pads through lever arms. Pneumatic cylinders actuated positively to compress springs and disengage brake pads from disks. During power failure, brakes automatically lock onto disks, producing highly reliable, fail-safe stops. System doubles as stopping brake and "parking" brake.

The development of the brake system of the BMW 850i including ABS and ASC. Entwicklung des Bremssystems des BMW 850i einschliesslich ABS und ASC

Energy Technology Data Exchange (ETDEWEB)

Kraft, H.J.; Leffler, H.

1990-02-01

The brake system of the new BMW 850i is described in the following. The brake actuation takes place via an hydraulic brake booster. The disc brakes at front and rear axle are arranged in diagnonal brake split. The 4-channel ABS is fitted as standard equipment. The ABS control unit also incorporates the algorithm for the Automatic Stability Control System ASC or ASC+T. The ASC+T shows improved traction compared with the pure stability system ASC and is standard in the BMW 850i with manual gear box. The automatic gear box equipped BMW 850i are supplied with ASC, the ASC+T is available as an option. Both systems, the ASC and the ASC+T are described with special view on the electronical and hydraulical network in the car. A performance comparison of the ASC-systems completes the description. (orig.).

Autonomous collision avoidance system by combined control of steering and braking using geometrically optimised vehicular trajectory

Science.gov (United States)

Hayashi, Ryuzo; Isogai, Juzo; Raksincharoensak, Pongsathorn; Nagai, Masao

2012-01-01

This study proposes an autonomous obstacle avoidance system not only by braking but also by steering, as one of the active safety technologies to prevent traffic accidents. The proposed system prevents the vehicle from colliding with a moving obstacle like a pedestrian jumping out from the roadside. In the proposed system, to avoid the predicted colliding position based on constant-velocity obstacle motion assumption, the avoidance trajectory is derived as connected two identical arcs. The system then controls the vehicle autonomously by the combined control of the braking and steering systems. In this paper, the proposed system is examined by real car experiments and its effectiveness is shown from the results of the experiments.

PROBABILISTIC APPROACH FOR THE DETERMINATION OF CUTS PERMISSIBLE BRAKING MODES ON THE GRAVITY HUMPS

Directory of Open Access Journals (Sweden)

Volodymyr BOBROVSKYI

2016-03-01

Full Text Available The paper presents the research results of cuts braking modes on the gravity humps. The objective of this paper is developing the methods for assessment of braking modes of cuts under conditions of fuzziness of their rolling properties, as well as selecting the permissible starting speed range of cuts from retardant positions. As a criterion for assessing the modes of target control of cut rolling speed, it was proposed to use an average gap size on a classification track at the established norms of probable exceeding of permissible speed of cars collision and their stop in retarders. As a criterion for evaluating the modes of interval control of cuts rolling speed, using the risk of their non-separation on the switches was proposed. Using the simulation modeling and mathematical statistics, the configuration of the range of permissible speed of cuts coming out from retardant positions has been set. The conducted researches allow simplifying the choice of cut braking modes in systems of automatic control of cut rolling speed.

Management Accounting in freight-forwarding companies

DEFF Research Database (Denmark)

Jensen, Jens Ocksen; Lynggaard, Peter

2002-01-01

The article describes the internal business management processes in a freight forwarding compagny on the operative/tactical level. This is done as an explorative study of how these processes are organized in two medium-sized Danish freight-forwarding compagnies....

Combined hydraulic and regenerative braking system

Science.gov (United States)

Venkataperumal, R.R.; Mericle, G.E.

1979-08-09

A combined hydraulic and regenerative braking system and method for an electric vehicle is disclosed. The braking system is responsive to the applied hydraulic pressure in a brake line to control the braking of the vehicle to be completely hydraulic up to a first level of brake line pressure, to be partially hydraulic at a constant braking force and partially regenerative at a linearly increasing braking force from the first level of applied brake line pressure to a higher second level of brake line pressure, to be partially hydraulic at a linearly increasing braking force and partially regenerative at a linearly decreasing braking force from the second level of applied line pressure to a third and higher level of applied line pressure, and to be completely hydraulic at a linearly increasing braking force from the third level to all higher applied levels of line pressure.

Design and analysis of an MR rotary brake for self-regulating braking torques.

Science.gov (United States)

Yun, Dongwon; Koo, Jeong-Hoi

2017-05-01

This paper presents a novel Magneto-rheological (MR) brake system that can self-regulate the output braking torques. The proposed MR brake can generate a braking torque at a critical rotation speed without an external power source, sensors, or controllers, making it a simple and cost-effective device. The brake system consists of a rotary disk, permanent magnets, springs, and MR fluid. The permanent magnets are attached to the rotary disk via the springs, and they move outward through grooves with two different gap distances along the radial direction of the stator due to the centrifugal force. Thus, the position of the magnets is dependent on the spin speed, and it can determine the magnetic fields applied to MR fluids. Proper design of the stator geometry gives the system unique torque characteristics. To show the performance of an MR brake system, the electromagnetic characteristics of the system are analyzed, and the torques generated by the brake are calculated using the result of the electromagnetic analysis. Using a baseline model, a parametric study is conducted to investigate how the design parameters (geometric shapes and material selection) affect the performance of the brake system. After the simulation study, a prototype brake system is constructed and its performance is experimentally evaluated. The experimental results show that the prototype produced the maximum torque of 1.2 N m at the rotational speed of 100 rpm. The results demonstrate the feasibility of the proposed MR brake as a speed regulator in rotating systems.

49 CFR 174.83 - Switching placarded rail cars, transport vehicles, freight containers, and bulk packagings.

Science.gov (United States)

2010-10-01

... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY RAIL Handling of Placarded Rail Cars, Transport... force than is necessary to complete the coupling; or (3) Struck by any car moving under its own momentum... its own momentum may be permitted to strike any placarded flatcar or any flatcar carrying a placarded...

WIND BRAKING OF MAGNETARS

International Nuclear Information System (INIS)

Tong, H.; Xu, R. X.; Qiao, G. J.; Song, L. M.

2013-01-01

We explore the wind braking of magnetars considering recent observations challenging the traditional magnetar model. There is evidence for strong multipole magnetic fields in active magnetars, but the dipole field inferred from spin-down measurements may be strongly biased by particle wind. Recent observations challenging the traditional model of magnetars may be explained naturally by the wind braking scenario: (1) the supernova energies of magnetars are of normal value; (2) the non-detection in Fermi observations of magnetars; (3) the problem posed by low magnetic field soft gamma-ray repeaters; (4) the relation between magnetars and high magnetic field pulsars; and (5) a decreasing period derivative during magnetar outbursts. Transient magnetars with L x rot may still be magnetic dipole braking. This may explain why low luminosity magnetars are more likely to have radio emissions. A strong reduction of the dipole magnetic field is possible only when the particle wind is very collimated at the star surface. A small reduction of the dipole magnetic field may result from detailed considerations of magnetar wind luminosity. In the wind braking scenario, magnetars are neutron stars with a strong multipole field. For some sources, a strong dipole field may no longer be needed. A magnetism-powered pulsar wind nebula will be one of the consequences of wind braking. For a magnetism-powered pulsar wind nebula, we should see a correlation between the nebula luminosity and the magnetar luminosity. Under the wind braking scenario, a braking index smaller than three is expected. Future braking index measurement of a magnetar may tell us whether magnetars are wind braking or magnetic dipole braking.

18. international {mu} symposium - expert meeting on brake systems; 18. Internationales {mu}-Symposium - Bremsen-Fachtagung

Energy Technology Data Exchange (ETDEWEB)

Breuer, B. [ed.

1999-12-01

The braking systems of passenger cars have become increasingly important for safe driving and driving dynamics (traction control, differential lock, brake assistance, electronic stabilising systems adaptive automatic speed control). At the same time operating-, noise- and vibration performance are expected to improve. Brake-by-wire, the technology of the future, will increase its potential as one component of the more and more strongly ``electrified`` cars. Design of operating characteristics will become important as the designer will have a lot of liberty in designing the effect of foot impact and slowing down of the vehicle and shall have to design the actuating pedal with great care. The is potential for further improvements in the following areas: dynamic cooperation of brakes, tyres and road, components (e.g. tyre sensors), advanced driver assistance systems. The XVIII. symposium held in Bad Neuenahr on October 23. and 24. 1998 dealt with several of the issues. The symposium, organised by BBA Friction GmbH brought together 240 brake experts from many countries. The contents of the conference are contained in this book (orig.) [Deutsch] In den letzten Jahren hat die Bedeutung der Bremsanlagen von Kraftfahrzeugen fuer Fahrdynamik und Fahrsicherheit ausserordentlich stark zugenommen (Traktionskontrolle, Differentialsperre, Bremsassistent, elektronische Fahrdynamikstabilisierung, adaptive automatische Fahrgeschwindigkeitsregelung). Gleichzeitig wachsen die Anforderungen an ihr Betriebs-, Geraeusch- und Schwingungsverhalten. Mit der zukuenftigen elektrischen Betaetigung der Bremse wird ihr Potential als wichtige Komponente im immer staerker `elektroinfizierten` Gesamtsystem Fahrzeug bedeutend erweitert. Hierbei wird auch die zukuenftige Auslegung der Betaetigungscharakteristik sehr wichtig, da der Konstrukteur im Wirkungszusammenhang Fusskraft/Fahrzeugverzoegerung grosse Freiheiten gewinnt und das Stellteil Bremspedal im Hinblick auf Kundenzufriedenheit und

Research of braking process of transport vehicle with hydraulic brake system parameters

OpenAIRE

Vladimirov, Oleg

2005-01-01

Emergency braking of a vehicle is bound with many factors, such as the behaviour of the driver, the drive of the vehicle braking system, the braking mechanisms, the condition of the tyres, and the properties of the pavement. This process involves all parameters of the system “the driver – the vehicle – the road”. In order to investigate the efficiency of braking process upon specific conditions, it is necessary to examine all physical processes that take place in the vehicle on pressing the b...

Dynamics of braking vehicles: from Coulomb friction to anti-lock braking systems

International Nuclear Information System (INIS)

Tavares, J M

2009-01-01

The dynamics of braking of wheeled vehicles is studied using the Coulomb approximation for the friction between road and wheels. The dependence of the stopping distance on the mass of the vehicle, on the number of its wheels and on the intensity of the braking torque is established. It is shown that there are two regimes of braking, with and without sliding. The advantage of using an anti-lock braking system (ABS) is put in evidence, and a quantitative estimate of its efficiency is proposed and discussed

Emissions and Air Quality Impacts of Freight Transportation

Science.gov (United States)

Bickford, Erica

Diesel freight vehicles (trucks + trains) are responsible for 20% of all U.S. nitrogen oxide (NOx) and 3% of fine particulate (PM2.5) emissions - pollutants that are harmful to human health. Freight tonnage is also projected to double over the next several decades, reaching 30 billion tons by 2050, increasing freight transport activity. Air quality impacts from increased activity, trade-offs between activity and vehicle technology improvements, as well as where to make infrastructure investments that encourage sustainable freight growth, are important considerations for transportation and air quality managers. To address these questions, we build a bottom-up roadway-by-roadway freight truck inventory (WIFE) and employ it to quantify emissions impacts of swapping biodiesel blends into the Midwest diesel freight truck fleet, and investigate emissions and air quality impacts of truck-to-rail freight modal shifts in the Midwest. We also evaluate the spatial and seasonal freight performance of WIFE modeled in a regional photochemical model (CMAQ) against satellite retrievals of nitrogen dioxide (NO2) from the Ozone Monitoring Instrument (OMI). Results show that spatial and seasonal distribution of biodiesel affects regional emissions impacts. Summer high-blend deployment yields a larger annual emissions reduction than year-round low-blend deployment, however, technological improvements in vehicle emissions controls between 2009 and 2018 dwarf the impacts of biodiesel. Truck-to-rail modal shift analysis found 40% of daily freight truck VMT could be shifted to rail freight, causing a 26% net reduction in NOx emissions, and 31% less carbon dioxide (CO2) emissions. Despite significant emissions impacts, air quality modeling results showed mostly localized near roadway air quality improvements, with small regional net changes; yet, federal regulation of CO2 emissions and/or rising costs of diesel fuel could motivate shifting freight to more fuel efficient rail. Evaluation of

Mathematical model of optimal empty rail car distribution at railway transport nodes

Directory of Open Access Journals (Sweden)

Aleksandr RAKHMANGULOV

2014-09-01

Full Text Available At present there are two trends in the market of rail freight transportation in Russia: freight owners put forward higher demands to the transportation quality (promptness of delivery in an effort to reduce storage costs by means of reducing the size of freight shipment; the structure of railcar traffic volume of the railways of Russia is getting more complex due to the reduction of the average shipment size and due to the transfer of railcar fleet ownership to a large number of operating companies. These trends significantly complicate operational management supervision of railway stations and transport nodes. Application of typical data from the information system about the railcar location at the transportation node is not enough for the dispatchers to make the best decision concerning the car traffic management. The dispatcher traffic control service needs some software-based models of efficient railcar distribution. The article is concerned with the description and development of the mathematical model of empty railcar distribution for loading at the railway transport node; this model will take into account the requirements of railcar owners in terms of their cars application, the operating work level of railroad stations of the transportation node and the possibility of adding the groups of empty railcars to the transfer trains, clean-up trains and industrial railway trains operating on a tight schedule. The developed model and the software package were implemented in the information system of the industrial railway of the major metallurgical enterprise - OJSC «Magnitogorsk Metallurgical Works», which processes up to two thousand of railcars belonging to different owners. This model made it possible to reduce the labour intensity of dispatcher operation planning the empty railcar distribution for loading and reduce the total time the railcars spend in the enterprise railway system.

IDEAL BRAKE FORCE DISTRIBUTION BETWEEN THE AXLES OF THE TWO-AXLE VEHICLE SERVICE BRAKE APPLICATIONS

Directory of Open Access Journals (Sweden)

M. Podryhalo

2015-07-01

Full Text Available The obtained analytical expressions allow us to evaluate the stability of two-axle vehicles at various slowdowns. An analytical expression for calculating the ideal according to condition stability ensuring of a two-axle vehicle at service brake applications of brake force distribution allows to offer automatic control devices for brake force adjucement. With decellerationg growth of the two-axle vehicle at service braking the braking force acting on the front axle should decrease relative to the brake force on the rear axle.

Freight transport in towns. Main report; Godstransport i byer. Hovedrapport

Energy Technology Data Exchange (ETDEWEB)

1992-10-01

The aim was to evaluate a number of possibilities for reducing energy consumption and thus air pollution caused by freight transport in urban areas. The Danish towns of Vejle and Roskilde were taken as examples and the two towns were compared with regard to the town plan, use of land area, the road network, amount of traffic and commercial structure. Economical aspects and the most important initiatives for improvements, including a decrease in traffic accidents, are discussed. These initiatives are coordination of transportation by firms, more drivers using the same vehicles, less frequent deliveries, optimazation of route planning, car sharing, special routes for lorries, traffic and speed control, better siting of new transport functions, re-siting of firms dependent on freight transport, the use of smaller vehicles where possible, no transport of people in trucks or vans, less use of bicycles for transporting messages, more use of underground pipes for transport of materials, lifting equipment for smaller vans and trucks, lifting equipment that is more flexible, motors turned off when loading and loading, reduction of emballage volume, and a more careful way of driving which can help to reduce energy consumption. A computer programme was constructed in order to calculate energy consumption in these relations, emission of hydrocarbons, carbon monoxide, nitrogen oxides and particles, transportation costs and number of traffic accidents. Results are presented in detail and discussed. (AB) (78 refs.).

Features of formation of car-traffic in a regional transportation system in conditions the multi-agents organization of a railway transportation

Directory of Open Access Journals (Sweden)

Aleksandr Leonidovich Kazakov

2011-09-01

Full Text Available As a result of structural reform of Russian railways, a host of agents that provide customers with loading resources, especially wagons for transport by railway. These processes reduce in efficiency of the car fleet, increasing transportation costs, shortage of cars for many customers, an increase of empty runs and, as a result, a depletion of a number of sections of the network carrying capacity at a reduced total volume of rail traffic. The article describes the reasons for this situation due to the mismatch occurred heterogeneity of rolling stock to existing planning conditions and tariffs. It is also shown that the inefficiency of decentralized car fleet contributes to the predominance of tree-type network, and the importance of this factor in the new environment has increased substantially. To ensure the efficient operation of rail transport as a systemic industry, providing mass-haul transport, it is proposed for integration into a regional logistics. Freight terminals regional logistics transportation and distribution system (RLTRS is appropriate to create on the basis of major freight railway stations. Thus, the adaptation of planning car traffic volume and train formation to modern standards, the establishment of tariff incentives and long-term changes in network configuration are considered as a prerequisite for the transformation of local transport and technological systems on the network of Russian railways into the integrated transport and logistics systems.

Impact of Brake Pad Structure on Temperature and Stress Fields of Brake Disc

OpenAIRE

Wang, Guoshun; Fu, Rong

2013-01-01

Utilizing ABAQUS finite element software, the study established the relationship between a brake pad structure and distributions of temperature and thermal stress on brake disc. By introducing radial structure factor and circular structure factor concepts, the research characterized the effect of friction block radial and circumferential arrangement on temperature field of the brake disc. A method was proposed for improving heat flow distribution of the brake disc through optimizing the posit...

Single acting translational/rotational brake

Science.gov (United States)

Allred, Johnny W. (Inventor); Fleck, Jr., Vincent J. (Inventor)

1996-01-01

A brake system is provided that applies braking forces on surfaces in both the translational and rotational directions using a single acting self-contained actuator that travels with the translational mechanism. The brake engages a mechanical lock and creates a frictional force on the translational structure preventing translation while simultaneously creating a frictional torque that prevents rotation of the vertical support. The system may include serrations on the braking surfaces to provide increased braking forces.

Sensotronic brake control. Braking with maximum efficiency; Die Sensotronic Brake Control. Bremsen auf hoechstem Niveau

Energy Technology Data Exchange (ETDEWEB)

Fischle, G.; Stoll, U.; Hinrichs, W.

2002-05-01

Sensotronic Brake Control (SBC) celebrated its world premiere when it was introduced into standard production along with the new SL in October 2001. This innovative brake system is also fitted as standard in the new E-Class. The design of the system components is identical to those used in the SL-Class. The software control parameters have been adapted to the conditions in the new saloon. (orig.) [German] Die Sensotronic Brake Control (SBC) wurde als Weltneuheit mit dem neuen SL im Oktober 2001 in Serie gebracht. Dieses innovative Bremssystem gehoert ebenfalls zur Serienausstattung der neuen E-Klasse. Die Systemkomponenten sind baugleich mit denen der SL-Klasse. Die Regelparameter der Software sind an die Verhaeltnisse der Limousine angepasst. (orig.)

Development of Regenerative Braking Co-operative Control System for Automatic Transmission-based Hybrid Electric Vehicle using Electronic Wedge Brake

OpenAIRE

Ko, Jiweon; Ko, Sungyeon; Bak, Yongsun; Jang, Mijeong; Yoo, Byoungsoo; Cheon, Jaeseung; Kim, Hyunsoo

2013-01-01

This research proposes a regenerative braking co-operative control system for the automatic transmission (AT)-based hybrid electric vehicle (HEV). The brake system of the subject HEV consists of the regenerative braking and the electronic wedge brake (EWB) friction braking for the front wheel, and the hydraulic friction braking for the rear wheel. A regenerative braking co-operative control algorithm is suggested for the regenerative braking and friction braking, which distributes the braking...

Intelligent car guidance system (parking support system); Chiteki sharyo yudo system (chusha shien system)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This system enables a driver to park the car at a predetermined spot without the driver seeing the outside scene. The system shows on a driver seat display the steps that the driver is to follow and thereby supports the driver when visibility is poor, when the parking space is difficult to approach, when the driver is a novice, or when the driver is aged. The system ensures accurate positioning of the car by showing the steering direction and angle, the car speed, and the force of braking to the driver. For this purpose, the system knows the absolute car position by the use of an RFID (Radio Frequency Identification) tag which is a kind of IC (Integrated Circuit) card and D-GPS (Differential-Global Positioning System), grasps the relative car position by the use of a gyroscope, and collects data from plural sensors, which are complementary to each other, such as a car-speed sensor and a steering sensor. (translated by NEDO)

Can cars and trucks coexist peacefully on highways? Analyzing the effectiveness of road safety policies in Europe.

Science.gov (United States)

Castillo-Manzano, José I; Castro-Nuño, Mercedes; Fageda, Xavier

2015-04-01

We examine the impact on the traffic accident rate of the interaction between trucks and cars on Europe's roads using a panel data set that covers the period 1999-2010. We find that rising motorization rates for trucks lead to higher traffic fatalities, while rising motorization rates for cars do not. Empirically, the model we build predicts the positive impact of stricter speed limit legislation for trucks in the reduction of road fatalities. These findings lend support to European strategies and aimed at promoting alternative modes of freight transport, including rail and maritime transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

Design and Analysis of a Novel Centrifugal Braking Device for a Mechanical Antilock Braking System.

Science.gov (United States)

Yang, Cheng-Ping; Yang, Ming-Shien; Liu, Tyng

2015-06-01

A new concept for a mechanical antilock braking system (ABS) with a centrifugal braking device (CBD), termed a centrifugal ABS (C-ABS), is presented and developed in this paper. This new CBD functions as a brake in which the output braking torque adjusts itself depending on the speed of the output rotation. First, the structure and mechanical models of the entire braking system are introduced and established. Second, a numerical computer program for simulating the operation of the system is developed. The characteristics of the system can be easily identified and can be designed with better performance by using this program to studying the effects of different design parameters. Finally, the difference in the braking performance between the C-ABS and the braking system with or without a traditional ABS is discussed. The simulation results indicate that the C-ABS can prevent the wheel from locking even if excessive operating force is provided while still maintaining acceptable braking performance.

Magnetorheological suspension electromagnetic brake

International Nuclear Information System (INIS)

Bica, Ioan

2004-01-01

The magnetorheological suspension (MRS) brake is of the monoblock type. The main part of the electromagnetic brake is an electromagnet, between whose poles two MRS disks are placed. For distances between disks of 0.65x10 -3 m±10%, revolutions of the electric motor, coupled to the electromagnetic brake, ranging between 200 and 1600 rev/min and braking powers of up to 85 W, there are no differences in revolutions between the disks of the electromagnetic brake. For fixed revolutions of the electric motor, the revolution of the parallel disk can be modified continuously by means of the intensity of the magnetic field. In all cases, the quantity of MRS is of 0.35x10 -3 kg

Assessing public benefits and costs of freight transportation projects : measuring shippers' value of delay on the freight system.

Science.gov (United States)

2012-07-01

Freight delay is detrimental to the national economy. In an effort to gauge the economic impact of freight delay due : to highway congestion, this project focuses on estimating shippers value of delay (VOD). We have accomplished : this through thr...

Brake force estimation for electromechanical vehicle brakes; Bremskraft-Rekonstruktion fuer elektromechanische Fahrzeugbremsen

Energy Technology Data Exchange (ETDEWEB)

Schwarz, R. [Continental Teves (Germany)

1999-06-01

Due to the increasing safety and comfort demands of the customer, the functionality of modern brake systems has grown continuously in the last years. However, implementation of the extended functionality in conventional brake hydraulics makes active electronic intervention necessary and therefore requires a lot of technical effort. In recent years the automotive supplier industry has started to develop brake systems which have electromechanical brake actuators generating the brake forces at the individual wheels. Electromechanically actuated wheel brakes need to be operated in a closed control loop. This paper introduces a new method to reconstruct the needed feedback value brake force from easy to measure signals. (orig.) [Deutsch] Aufgrund des gestiegenen Sicherheits- und Komfortbewusstseins der Fahrzeugkaeufer ist die Funktionsvielfalt moderner Bremssysteme in den letzten Jahren staendig gewachsen. Die Umsetzung der erweiterten Funktionalitaet mittels konventioneller Bremsenhydraulik ist jedoch durch den elektronischen, aktiven Eingriff sehr aufwendig. In den letzten Jahren hat daher die Automobilzulieferindustrie begonnen, Bremssysteme zu entwickeln, bei denen die Bremskraft an den einzelnen Raedern von elektromechanischen Bremsaktuatoren aufgebracht wird. Elektromechanisch betaetigte Radbremsen muessen im geschlossenen Regelkreis betrieben werden. Der vorliegende Beitrag, der im Rahmen einer Forschungskooperation zwischen Continental Teves und dem Institut fuer Automatisierungstechnik der TU Darmstadt entstand stellt ein Verfahren vor, mit dem die dafuer benoetigte Rueckfuehrungsgroesse `Bremskraft` aus einfach messbaren Signalen rekonstruiert werden kann. (orig.)

Dynamics of Braking Vehicles: From Coulomb Friction to Anti-Lock Braking Systems

Science.gov (United States)

Tavares, J. M.

2009-01-01

The dynamics of braking of wheeled vehicles is studied using the Coulomb approximation for the friction between road and wheels. The dependence of the stopping distance on the mass of the vehicle, on the number of its wheels and on the intensity of the braking torque is established. It is shown that there are two regimes of braking, with and…

49 CFR 393.52 - Brake performance.

Science.gov (United States)

2010-10-01

...: Type of motor vehicle Service brake systems Braking force as a percentage of gross vehicle or... specifications for performance-based brake testers for commercial motor vehicles, where braking force is the sum of the braking force at each wheel of the vehicle or vehicle combination as a percentage of gross...

Friction and Braking Application of Unhazardous Palm Slag Brake Pad Composite

Science.gov (United States)

Khoni, Norizzahthul Ainaa Abdul; Ruzaidi Ghazali, Che Mohd; Bakri Abdullah, Mohd Mustafa Al

2018-03-01

This paper reveals new alternative friction materials for brake pads. Palm slag was studied as new friction materials in brake pads but its much harder made it difficult to be applied. As a way to reduce the hardness, tire dust was including as purpose on stabilizing the hardness of brake pads. The palm slag was sieves to get desired size that is 150 μm, 300 μm and 600 μm. The percentage weight of materials used are 20% graphite, 20% aluminium oxide, 20% steel fiber, 20% polyester resin and another 40% are varied between tire dust and palm slag. All of materials were blend and compress by using hot pressed machine. The composites properties that were examined are density, porosity, hardness, compressive strength, microstructure analysis and wear rate. The composition of 30% palm slag, 10% tire dust and larger size of filler give better result of mechanical properties and less wear rate of brake pads composites. Then, palm slag can be used in producing of non asbestos brake pads.

78 FR 75442 - Designation of the Primary Freight Network

Science.gov (United States)

2013-12-11

...] Designation of the Primary Freight Network AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice... period for the Designation of the highway Primary Freight Network (PFN) notice, which was published on... the complete National Freight Network (NFN), and to solicit comments on aspects of the NFN. The five...

US Advanced Freight and Passenger MAGLEV System

Science.gov (United States)

Morena, John J.; Danby, Gordon; Powell, James

1996-01-01

Japan and Germany will operate first generation Maglev passenger systems commercially shortly after 2000 A.D. The United States Maglev systems will require sophisticated freight and passenger carrying capability. The U.S. freight market is larger than passenger transport. A proposed advanced freight and passenger Maglev Project in Brevard County Florida is described. Present Maglev systems cost 30 million dollars or more per mile. Described is an advanced third generation Maglev system with technology improvements that will result in a cost of 10 million dollars per mile.

THE LIFETIME EXTENSION OF CAR AXLES TYPES OF RU1 AND RUSH WHEELSET FREIGHT CARS, RESTORED BY THE METHOD OF PLASMA-ARC METALLIZATION OF THE NECK AND UNDER PARTS MANUAL

Directory of Open Access Journals (Sweden)

V. I. Zelenin

2009-03-01

Full Text Available The restoration method for the journals and wheel seats of the freight wagon wheelsets by means of plasma-arc metallization is presented and the results of the bench fatigue tests with the advisable operation life of the axles restored are given.

Hydraulic brake-system for a bicycle

NARCIS (Netherlands)

Van Frankenhuyzen, J.

2007-01-01

The invention relates to a hydraulic brake system for a bicycle which may or may not be provided with an auxiliary motor, comprising a brake disc and brake claws cooperating with the brake disc, as well as fluid-containing channels (4,6) that extend between an operating organ (1) and the brake

Geometric optimal design of a magneto-rheological brake considering different shapes for the brake envelope

International Nuclear Information System (INIS)

Nguyen, Q H; Lang, V T; Nguyen, N D; Choi, S B

2014-01-01

When designing a magneto-rheological brake (MRB), it is well known that the shape of the brake envelope significantly affects the performance characteristics of the brake. In this study, different shapes for the MR brake envelope, such as rectangular, polygonal or spline shape, are considered and the most suitable shape identified. MRBs with different envelope shapes are introduced followed by the derivation of the braking torque based on Bingham-plastic behavior of the magneto-rheological fluid (MRF). Optimization of the design of the MRB with different envelope shapes is then done. The optimization problem is to find the optimal value for the significant geometric dimensions of the MRB that can produce a certain required braking torque while the brake mass is minimized. A finite element analysis integrated with an optimization tool is employed to obtain optimal solutions for the MRBs. From the results, the most suitable shape for the brake envelope is identified and discussed with the reduction of mass. In addition, the results of the analysis are compared with the experimental results to verify the proposed optimal design characteristics. (paper)

Geometric optimal design of a magneto-rheological brake considering different shapes for the brake envelope

Science.gov (United States)

Nguyen, Q. H.; Lang, V. T.; Nguyen, N. D.; Choi, S. B.

2014-01-01

When designing a magneto-rheological brake (MRB), it is well known that the shape of the brake envelope significantly affects the performance characteristics of the brake. In this study, different shapes for the MR brake envelope, such as rectangular, polygonal or spline shape, are considered and the most suitable shape identified. MRBs with different envelope shapes are introduced followed by the derivation of the braking torque based on Bingham-plastic behavior of the magneto-rheological fluid (MRF). Optimization of the design of the MRB with different envelope shapes is then done. The optimization problem is to find the optimal value for the significant geometric dimensions of the MRB that can produce a certain required braking torque while the brake mass is minimized. A finite element analysis integrated with an optimization tool is employed to obtain optimal solutions for the MRBs. From the results, the most suitable shape for the brake envelope is identified and discussed with the reduction of mass. In addition, the results of the analysis are compared with the experimental results to verify the proposed optimal design characteristics.

Antiskid braking system

Science.gov (United States)

Pazdera, J. S.

1974-01-01

Published report describes analytical development and simulation of braking system. System prevents wheels from skidding when brakes are applied, significantly reducing stopping distance. Report also presents computer simulation study on system as applied to aircraft.

Baseline Testing of the Club Car Carryall With Asymmetric Ultracapacitors

Science.gov (United States)

Eichenberg, Dennis J.

2003-01-01

The NASA John H. Glenn Research Center initiated baseline testing of the Club Car Carryall with asymmetric ultracapacitors as a way to reduce pollution in industrial settings, reduce fossil fuel consumption, and reduce operating costs for transportation systems. The Club Car Carryall provides an inexpensive approach to advance the state of the art in electric vehicle technology in a practical application. The project transfers space technology to terrestrial use via non-traditional partners, and provides power system data valuable for future space applications. The work was done under the Hybrid Power Management (HPM) Program, which includes the Hybrid Electric Transit Bus (HETB). The Carryall is a state of the art, ground up, electric utility vehicle. A unique aspect of the project was the use of a state of the art, long life ultracapacitor energy storage system. Innovative features, such as regenerative braking through ultracapacitor energy storage, are planned. Regenerative braking recovers much of the kinetic energy of the vehicle during deceleration. The Carryall was tested with the standard lead acid battery energy storage system, as well as with an asymmetric ultracapacitor energy storage system. The report concludes that the Carryall provides excellent performance, and that the implementation of asymmetric ultracapacitors in the power system can provide significant performance improvements.

DETERMINATION OF OBJECTIVES FOR URBAN FREIGHT POLICY

Directory of Open Access Journals (Sweden)

Daniel Kaszubowski

2014-12-01

Full Text Available Background: Decisions regarding strategic planning of urban freight transport very often are based on superficial assumptions inadequately reflecting the actual character of encountered challenges. The trend may be observed to adapt isolated solutions without supporting measures and verification of expected outcomes. Selected urban freight solutions have a significant potential to alleviate transport related problems, but they require unorthodox approach beyond standard traffic planning and road management. City's current planning experience must be taken into account to plan an optimized sequence of actions. Method: Due to complexity of the problem and specific decision making factors the analytic network process ANP was selected to determine relevant objective of the urban freight policy. Gdynia was selected as the subject for modeling with a review of the current freight planning practice as a first step. Then, classification of policy objective and their prerequisites were identified supported with descriptive feasibility assessment. This allowed for a development of the ANP decision-making model. Results: Considered objectives for urban freight policy were identified were optimization, reduction and transfer. After verifying relevant decision factors optimization was selected as the most feasible option for Gdynia. Other alternatives were rated around four times lower with a slight prevalence of reduction over transfer. Such ranking reflects current planning practice and availability of transferable experiences. Despite the indicative results, it must be stressed that urban freight planning should be based on the long term methodical approach not to exclude any emerging possibilities. 

South Africa’s freight rail reform: A demand-driven perspective

Directory of Open Access Journals (Sweden)

Jan H. Havenga

2014-11-01

Full Text Available During the 20th century, freight transport in South Africa was employed to attain politicoeconomic ideals, resulting in the overprotection of rail and overregulation of road transport. Increasing industry pressure, combined with the international deregulation trend, led to deregulation in 1988. Myopia resulted in a rail investment hiatus and exponential growth in high-value, long-distance road transport, causing excessive logistics and externality costs for the country. The aim of this study was to propose a freight rail reform agenda based on, (1 lessons from past freight transport policy efforts and (2 the results of freight transport market segmentation driven by models developed over the past two decades. For the study, freight flows were modelled by disaggregating the national input–output model into 372 origin–destination pairs and 71 commodity groups, followed by distance decay gravitymodelling. Logistics costs were calculated by relating commodity-level freight flows to the costs of fulfilling associated logistical functions. The standard management approach of founding strategy development on market-driven segmentation provides a neutral input to steer rail reform discussions in South Africa. Market segmentation points to a dualistic rail reform agenda, enabling both a profit-driven core and a development-driven branch line network. Freight flow insights are steering the policy reform debate towards long-term freight strategy development and optimal freight logistics network design.

Quantification of brake data acquired with a brake power meter during simulated cross-country mountain bike racing.

Science.gov (United States)

Miller, Matthew C; Fink, Philip W; Macdermid, Paul W; Stannard, Stephen R

2018-01-17

There is currently a dearth of information describing cycling performance outside of propulsive and physiological variables. The aim of the present study was to utilise a brake power meter to quantify braking during a multi-lap cross-country mountain bike time trial and to determine how braking affects performance. A significant negative association was determined between lap time and brake power (800.8 ± 216.4 W, mean ± SD; r = -0.446; p  0.05) which was attributed to decreased brake work (p < 0.05) and brake time (p < 0.05) in both the front and rear brakes by the final lap. A multiple regression model incorporating braking and propulsion was able to explain more of the variance in lap time (r 2  = 0.935) than propulsion alone (r 2  = 0.826). The present study highlights that riders' braking contributes to mountain bike performance. As riders repeat a cross-country mountain bike track, they are able to change braking, which in turn can counterbalance a reduction in power output. Further research is required to understand braking better.

Ontario freight movement study

International Nuclear Information System (INIS)

Anon.

1995-11-01

The freight (cargo) transportation sector accounts for a major use of fossil fuels and contributes significantly to greenhouse gas emissions. A study was conducted to estimate and forecast emissions from transportation in Ontario, by mode, over the next 15 years, and to examine ways in which those emissions could be reduced. Published data of freight transportation industries was used to examine the fuel consumption characteristics of each mode, followed by a review of emission rates. It was determined that truck transportation accounts for most CO 2 emissions (about 70%). Rail follows with 21% and the marine and air modes contribute relatively small shares (6% and 2%). New intermodal technologies being introduced by the railways were discussed. They have been designed to make intermodal transport more accessible to a wider segment of the freight market. A recommendation was made which would require all truck shipments over 500 km, accounting for fully one half of truck tonne-km, to have their line-haul component diverted to this new more fuel-efficient mode (i.e., from truck to rail). refs., tabs., figs

Performance requirements for locomotive braking systems

CSIR Research Space (South Africa)

Vermaak, P

2000-02-01

Full Text Available operated “Neutral Brake”. This brake may become active immediately or after a certain time delay when the controller is placed in the neutral position or moved into the neutral position by the “dead-man’s device”. Because this brake will interfere... in testing emergency brake systems due to the inherent braking action of the service brakes and/or locomotive controllers; • Potential problems limitations to braking effort associated with the prime movers and/or hydraulic systems on hydrostatically...

78 FR 11727 - National Freight Advisory Committee

Science.gov (United States)

2013-02-19

... performance in freight transportation; (6) development of freight transportation investment, data, and...; (3) availability and willingness to serve; and (4) relevant experience in working in committees and... minorities, women, and persons with disabilities. Please note, however, that federally registered lobbyists...

78 FR 10687 - Notice of Receipt of Petition for Decision That Nonconforming 1992 Porsche Carrera Passenger Cars...

Science.gov (United States)

2013-02-14

... Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems, 106 Brake Hoses, 113 Hood Latch... vehicle is equipped with an automatic restraint system that consists of dual front airbags and knee... Passenger Cars Are Eligible for Importation AGENCY: National Highway Traffic Safety Administration, DOT...

Passenger and freight transport perspectives for 2035. Background report for transport policy discussion; Henkiloe- ja tavaraliikenteen kehityskuva 2035. Taustaraportti liikennepoliittiseen keskusteluun

Energy Technology Data Exchange (ETDEWEB)

Luukkonen, T.; Maekelae, T.; Pollanen, M.; Kalenoja, H.; Mantynen, J.; Rantala, J.

2012-07-01

This study aims to image the perspectives for future transport on the basis of existing estimates and expert views. The results of this study offer a justified perception of how Finnish passenger and freight transport will develop up to year 2035. The study also includes six 'what if' analysis which address how six individual and important changes could affect transports. The development of population and the economy are key factors in the operating environment of passenger and freight transport. To a large extent, they determine the development of the demand for passenger and freight transport. Earlier population forecasts have underestimated population growth in Finland. Uncertainty also surrounds regional demographic development, which is connected both to the development of community structure and land use, and to time use and consumption habits associated with travel preferences. The development of the economy, which also involves considerable uncertainty, is connected to population through developments in employment and income levels, among others, while growing workplace areas also attract people and increase commuting, for example. Changing travel habits and ageing of the population influence the overall demand for passenger transport. Efforts are being made to promote walking, cycling and the use of public transport. In the future these means of transport will be supported by factors such as increased awareness of the environment and health, and concentration of population in cities. While the aim is to constrain the growth of passenger car traffic, rising income levels and travel distances in the operating environment will serve to increase passenger car traffic and the demand for long-distance train, flight and bus traffic. The supply of different transport methods and the costs of their use will, for their part, affect transport mode distribution. The development of the economy and various sectors will determine the demand for freight

Research on Linear Wireless Sensor Networks Used for Online Monitoring of Rolling Bearing in Freight Train

International Nuclear Information System (INIS)

Wang Nan; Meng Qingfeng; Zheng Bin; Li Tong; Ma Qinghai

2011-01-01

This paper presents a Wireless Sensor Networks (WSNs) technique for the purpose of on-line monitoring of rolling bearing in freight train. A new technical scheme including the arrangements of sensors, the design of sensor nodes and base station, routing protocols, signal acquirement, processing and transmission is described, and an on-line monitoring system is established. Considering the approximately linear arrangements of cars and the running state of freight train, a linear topology structure of WSNs is adopted and five linear routing protocols are discussed in detail as to obtain the desired minimum energy consumption of WSNs. By analysing the simulation results, an optimal multi-hop routing protocol named sub-section routing protocol according to equal distance is adopted, in which all sensor nodes are divided into different groups according to the equal transmission distance, the optimal transmission distance and number of hops of routing protocol are also studied. We know that the communication consumes significant power in WSNs, so, in order to save the limit power supply of WSNs, the data compression and coding scheme based on lifting integer wavelet and embedded zerotree wavelet (EZW) algorithms is studied to reduce the amounts of data transmitted. The experimental results of rolling bearing have been given at last to verify the effectiveness of data compression algorithm. The on-line monitoring system of rolling bearing in freight train will be applied to actual application in the near future.

Research on Linear Wireless Sensor Networks Used for Online Monitoring of Rolling Bearing in Freight Train

Energy Technology Data Exchange (ETDEWEB)

Wang Nan; Meng Qingfeng; Zheng Bin [Theory of Lubrication and Bearing Institute, Xi' an Jiaotong University Xi' an, 710049 (China); Li Tong; Ma Qinghai, E-mail: heroyoyu.2009@stu.xjtu.edu.cn [Xi' an Rail Bureau, Xi' an, 710054 (China)

2011-07-19

This paper presents a Wireless Sensor Networks (WSNs) technique for the purpose of on-line monitoring of rolling bearing in freight train. A new technical scheme including the arrangements of sensors, the design of sensor nodes and base station, routing protocols, signal acquirement, processing and transmission is described, and an on-line monitoring system is established. Considering the approximately linear arrangements of cars and the running state of freight train, a linear topology structure of WSNs is adopted and five linear routing protocols are discussed in detail as to obtain the desired minimum energy consumption of WSNs. By analysing the simulation results, an optimal multi-hop routing protocol named sub-section routing protocol according to equal distance is adopted, in which all sensor nodes are divided into different groups according to the equal transmission distance, the optimal transmission distance and number of hops of routing protocol are also studied. We know that the communication consumes significant power in WSNs, so, in order to save the limit power supply of WSNs, the data compression and coding scheme based on lifting integer wavelet and embedded zerotree wavelet (EZW) algorithms is studied to reduce the amounts of data transmitted. The experimental results of rolling bearing have been given at last to verify the effectiveness of data compression algorithm. The on-line monitoring system of rolling bearing in freight train will be applied to actual application in the near future.

Urban freight transportation : challenges, failures and successes

NARCIS (Netherlands)

Kant, G.; Quak, H.; Peeters, R.; van Woensel, T.; Zijm, H.; Klumpp, M.; Clausen, U.; ten Hompel, M.

2016-01-01

In this paper, we present the challenges, failures and successes on urban freight transportation. We first identify the various involved stakeholders with their interests. Then we evaluate a large number of urban freight transport initiatives and identify lessons learned, which are distinguished in

Consolidation and coordination in urban freight transport

NARCIS (Netherlands)

van Heeswijk, W.J.A.

2017-01-01

Due to growing urbanization, fragmentation of freight flows, and increasingly strict delivery conditions, cities around the world have to deal with a vastly increasing number of freight transport flows. Carriers are unable to efficiently bundle these flows, resulting in inefficient urban transport.

Urban freight transportation : Challenges, failure, and successes

NARCIS (Netherlands)

Kant, Goos; Quak, H.; Peeters, Rene; Woensel van, T.; Zijm, H.; Klumpp, M.; Clausen, U.; Ten Hompel, M.

2016-01-01

In this paper, we present the challenges, failures and successes on urban freight transportation. We first identify the various involved stakeholders with their interests. Then we evaluate a large number of urban freight transport initiatives and identify lessons learned, which are distinguished in

Possible stibnite transformation at the friction surface of the semi-metallic friction composites designed for car brake linings

Science.gov (United States)

Matějka, V.; Lu, Y.; Matějková, P.; Smetana, B.; Kukutschová, J.; Vaculík, M.; Tomášek, V.; Zlá, S.; Fan, Y.

2011-12-01

After a friction process several changes in phase composition of friction composites are often registered. High temperature, accompanied by high pressure induced during braking can cause initiation of chemical reactions which do not run at room or elevated temperatures under the atmospheric pressure. Most of the studies in the field of tribochemistry at friction surfaces of automotive semi-metallic brake linings deal with phenolic resin degradation and corrosion of metallic components. The paper addresses the formation of elemental antimony as well as the alloying process of iron with antimony observed on the surface of laboratory prepared semi-metallic friction composites containing stibnite. The role of alumina abrasives in the process of stibnite transformation is also discussed and mechanism of stibnite transformation was outlined.

Thermal analysis and temperature characteristics of a braking resistor for high-speed trains for changes in the braking current

Science.gov (United States)

Lee, Dae-Dong; Kang, Hyun-Il; Shim, Jae-Myung

2015-09-01

Electric brake systems are used in high-speed trains to brake trains by converting the kinetic energy of a railway vehicle to electric energy. The electric brake system consists of a regenerative braking system and a dynamic braking system. When the electric energy generated during the dynamic braking process is changed to heat through the braking resistor, the braking resistor can overheat; thus, failures can occur to the motor block. In this paper, a braking resistor for a high-speed train was used to perform thermal analyses and tests, and the results were analyzed. The analyzed data were used to estimate the dependence of the brake currents and the temperature rises on speed changes up to 300 km/h, at which a test could not be performed.

Assessing the potential benefits of the motorcycle autonomous emergency braking using detailed crash reconstructions.

Science.gov (United States)

Savino, Giovanni; Giovannini, Federico; Baldanzini, Niccolò; Pierini, Marco; Rizzi, Matteo

2013-01-01

The aim of this study was to assess the feasibility and quantitative potential benefits of a motorcycle autonomous emergency braking (MAEB) system in fatal rear-end crashes. A further aim was to identify possible criticalities of this safety system in the field of powered 2-wheelers (PTWs; e.g., any additional risk introduced by the system itself). Seven relevant cases from the Swedish national in-depth fatal crash database were selected. All crashes involved car-following in which a non-anti-lock braking system (ABS)-equipped motorcycle was the bullet vehicle. Those crashes were reconstructed in a virtual environment with Prescan, simulating the road scenario, the vehicles involved, their precrash trajectories, ABS, and, alternatively, MAEB. The MAEB chosen as reference for the investigation was developed within the European Commission-funded Powered Two-Wheeler Integrated Safety (PISa) project and further detailed in later studies, with the addition of the ABS functionality. The boundary conditions of each simulation varied within a range compatible with the uncertainty of the in-depth data and also included a range of possible rider behaviors including the actual one. The benefits of the MAEB were evaluated by comparing the simulated impact speed in each configuration (no ABS/MAEB, ABS only, MAEB). The MAEB proved to be beneficial in a large number of cases. When applicable, the benefits of the system were in line with the expected values. When not applicable, there was no clear evidence of an increased risk for the rider due to the system. MAEB represents an innovative safety device in the field of PTWs, and the feasibility of such a system was investigated with promising results. Nevertheless, this technology is not mature yet for PTW application. Research in the field of passenger cars does not directly apply to PTWs because the activation logic of a braking system is more challenging on PTWs. The deployment of an autonomous deceleration would affect the

Comparative engine performance and emission analysis of CNG and gasoline in a retrofitted car engine

International Nuclear Information System (INIS)

Jahirul, M.I.; Masjuki, H.H.; Saidur, R.; Kalam, M.A.; Jayed, M.H.; Wazed, M.A.

2010-01-01

A comparative analysis is being performed of the engine performance and exhaust emission on a gasoline and compressed natural gas (CNG) fueled retrofitted spark ignition car engine. A new 1.6 L, 4-cylinder petrol engine was converted to the computer incorporated bi-fuel system which operated with either gasoline or CNG using an electronically controlled solenoid actuated valve mechanism. The engine brake power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature and exhaust emissions (unburnt hydrocarbon, carbon mono-oxide, oxygen and carbon dioxides) were measured over a range of speed variations at 50% and 80% throttle positions through a computer based data acquisition and control system. Comparative analysis of the experimental results showed 19.25% and 10.86% reduction in brake power and 15.96% and 14.68% reduction in brake specific fuel consumption (BSFC) at 50% and 80% throttle positions respectively while the engine was fueled with CNG compared to that with the gasoline. Whereas, the retrofitted engine produced 1.6% higher brake thermal efficiency and 24.21% higher exhaust gas temperature at 80% throttle had produced an average of 40.84% higher NO x emission over the speed range of 1500-5500 rpm at 80% throttle. Other emission contents (unburnt HC, CO, O 2 and CO 2 ) were significantly lower than those of the gasoline emissions.

Optimal design and selection of magneto-rheological brake types based on braking torque and mass

International Nuclear Information System (INIS)

Nguyen, Q H; Lang, V T; Choi, S B

2015-01-01

In developing magnetorheological brakes (MRBs), it is well known that the braking torque and the mass of the MRBs are important factors that should be considered in the product’s design. This research focuses on the optimal design of different types of MRBs, from which we identify an optimal selection of MRB types, considering braking torque and mass. In the optimization, common types of MRBs such as disc-type, drum-type, hybrid-type, and T-shape types are considered. The optimization problem is to find an optimal MRB structure that can produce the required braking torque while minimizing its mass. After a brief description of the configuration of the MRBs, the MRBs’ braking torque is derived based on the Herschel-Bulkley rheological model of the magnetorheological fluid. Then, the optimal designs of the MRBs are analyzed. The optimization objective is to minimize the mass of the brake while the braking torque is constrained to be greater than a required value. In addition, the power consumption of the MRBs is also considered as a reference parameter in the optimization. A finite element analysis integrated with an optimization tool is used to obtain optimal solutions for the MRBs. Optimal solutions of MRBs with different required braking torque values are obtained based on the proposed optimization procedure. From the results, we discuss the optimal selection of MRB types, considering braking torque and mass. (technical note)

Brake Stops Both Rotation And Translation

Science.gov (United States)

Allred, Johnny W.; Fleck, Vincent J., Jr.

1995-01-01

Combination of braking and positioning mechanisms allows both rotation and translation before brake engaged. Designed for use in positioning model airplane in wind tunnel. Modified version used to position camera on tripod. Brake fast and convenient to use; contains single actuator energizing braking actions against both rotation and translation. Braking actuator electric, but pneumatic actuator could be used instead. Compact and lightweight, applies locking forces close to load, and presents minimal cross section to airflow.

A disaggregate freight transport model of transport chain and shipment size choice

NARCIS (Netherlands)

Windisch, E.; De Jong, G.C.; Van Nes, R.; Hoogendoorn, S.P.

2010-01-01

The field of freight transport modelling is relatively young compared to passenger transport modelling. However, some key issues in freight policy, like growing freight shares on the road, advanced logistics concepts or emerging strict freight transport regulations, have been creating increasing

Cars Gone Wild: The Major Contributor to Unintended Acceleration in Automobiles is Pedal Error.

Science.gov (United States)

Schmidt, Richard A; Young, Douglas E

2010-01-01

"Unintended-acceleration" automobile accidents typically begin when the driver first enters the car, starts the engine, and intends to press his/her right foot on the brake while shifting from Park to a drive gear (Drive or Reverse). The driver reports an unintended (uncommanded) full-throttle acceleration, coupled with a loss of braking, until the episode ends in a crash. Pedal misapplications - where the right foot contacts the accelerator instead of the brake that was intended - have been linked to these accidents (Schmidt, 1989, 1993) which, in the 1980s, were thought to occur only at the start of a driving cycle (and/or with the car in Park). But, in 1997, we identified over 200 pedal errors as the cause of accidents reported in the North Carolina database; these crashes occurred during the driving cycle (Schmidt et al., 1997), and/or with the vehicle in a gear other than Park. Our present work provides a more thorough analysis of these North Carolina Police Accident Reports from 1979 to 1995. The vast majority of pedal misapplications (over 92%) (a) occurred during the driving cycle, (b) were generally in "unhurried" conditions, and (c) were categorically separate from those events referred to as unintended-acceleration episodes at start-up. These ideas are explanatory for the recent (2009-2010) surge of unintended-acceleration reports, perhaps even suggesting that all of these crashes are caused by pedal errors, and that none of them are based on some vehicle defect(s).

Barriers to and enablers for European rail freight transport for integrated door-to-door logistics service. Part 2: Enablers for multimodal rail freight transport

Directory of Open Access Journals (Sweden)

Dewan Md Zahurul ISLAM

2014-12-01

Full Text Available The objective of this paper is to examine and identify barriers to and enablers for the European rail freight transport services as a transport chain partner along the supply chains in the changing market scenario. The changing market scenario includes, among others, requiring 'door-to-door' rather than 'terminal to terminal' and integrated service, competitive ability to attract non-rail cargo type, changes in the customer requirements (e.g. reliable service and changes in the operational requirements and practices. Using a literature review method, the paper is presented in two parts. The part 1 focuses on the identification of barriers to the European rail freight service by reviewing freight logistics services for global supply chains followed by the current performance of European rail freight transport followed by a discussion on the rail freight market liberalisation in Europe. Then rail freight transport in the Unites States (U.S. is discussed. The research notes that although the background, scope and necessity for reform measures in Europe differ from those of the U.S., some lessons can be learned and the main lesson is that an appropriate reform measure can enhance rail sector competitive ability in Europe. The part 2 of the paper is dedicated to recommend some concrete steps and actions as enablers to remove the barriers identified in the part 1 to develop multimodal rail freight transport. The enablers for multimodal rail freight transport include: •\tEuropean rail freight transport market needs full liberalisation so that incumbent and new entrants can compete freely. •\tThe rail operators need to acquire service (e.g. customer tailored services, door to door service quality offered by road freight operators. •\tThey need to conduct a combination of ‘terminal-to-terminal’ and door-to-door operations, as and when needed; •\tThey must build partnership with freight forwarder or 3PLs to include all types of customers

Fundamentals of automotive and engine technology standard drives, hybrid drives, brakes, safety systems

CERN Document Server

2014-01-01

Hybrid drives and the operation of hybrid vehicles are characteristic of contemporary automotive technology. Together with the electronic driver assistant systems, hybrid technology is of the greatest importance and both cannot be ignored by today’s car drivers. This technical reference book provides the reader with a firsthand comprehensive description of significant components of automotive technology. All texts are complemented by numerous detailed illustrations. Contents History of the automobile.- History of the Diesel engine.- Areas of use for Diesel engines.- Basic principles of the Diesel engine.- Basic principles of Diesel fuel-injection.- Basic principles of the gasoline engine.- Inductive ignition system.- Transmissions for motor vehicles.- Motor vehicle safety.- Basic principles of vehicle dynamics.- Car braking systems.- Vehicle electrical systems.- Overview of electrical and electronic systems in the vehicle.- Control of gasoline engines.- Control of Diesel engines.- Lighting technology.- Elec...

Thermal analysis on motorcycle disc brake geometry

Science.gov (United States)

W. M. Zurin W., S.; Talib, R. J.; Ismail, N. I.

2017-08-01

Braking is a phase of slowing and stop the movement of motorcycle. During braking, the frictional heat was generated and the energy was ideally should be faster dissipated to surrounding to prevent the built up of the excessive temperature which may lead to brake fluid vaporization, thermoelastic deformation at the contact surface, material degradation and failure. In this paper, solid and ventilated type of motorcycle disc brake are being analyse using Computational Fluid Dynamic (CFD) software. The main focus of the analysis is the thermal behaviour during braking for solid and ventilated disc brake. A comparison between both geometries is being discussed to determine the better braking performance in term of temperature distribution. It is found that ventilated disc brake is having better braking performance in terms of heat transfer compare to solid disc.

Modeling and design of cooperative braking in electric and hybrid vehicles using induction machine and hydraulic brake

Directory of Open Access Journals (Sweden)

Zaini Dalimus

2016-07-01

Full Text Available In mixed-mode braking applications, the electric motor / generator (M/G and hydraulic pressure valve are controlled to meet the driver’s braking demand. Controlling these braking elements is achieved by modulating the current generated by the M/G and adjusting the fluid pressure to the wheel brake cylinders. This paper aims to model and design combined regenerative and hydraulic braking systems which, comprise an induction electric machine, inverter, NiMH battery, controller, a pressure source, pressure control unit, and brake calipers. A 15 kW 1500 rpm induction machine equipped with a reduction gear having a gear ratio of 4 is used. A hydraulic brake capable to produce fluid pressure up to 40 bar is used. Direct torque control and pressure control are chosen as the control criteria in the M/G and the hydraulic solenoid valve. The braking demands for the system are derived from the Federal Testing Procedure (FTP drive cycle. Two simulation models have been developed in Matlab®/Simulink® to analyze the performance of the control strategy in each braking system. The developed model is validated through experiment. It is concluded that the control system does introduce torque ripple and pressure oscillation in the braking system, but these effects do not affect vehicle braking performance due to the high frequency nature of pressure fluctuation and the damping effect of the vehicle inertia. Moreover, experiment results prove the effectiveness of the developed model.

48 CFR 52.247-7 - Freight Excluded.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Freight Excluded. 52.247-7... AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 52.247-7 Freight... contracts for transportation or for transportation-related services when any commodities or types of...

Freight Calculation Model: A Case Study of Coal Distribution

Science.gov (United States)

Yunianto, I. T.; Lazuardi, S. D.; Hadi, F.

2018-03-01

Coal has been known as one of energy alternatives that has been used as energy source for several power plants in Indonesia. During its transportation from coal sites to power plant locations is required the eligible shipping line services that are able to provide the best freight rate. Therefore, this study aims to obtain the standardized formulations for determining the ocean freight especially for coal distribution based on the theoretical concept. The freight calculation model considers three alternative transport modes commonly used in coal distribution: tug-barge, vessel and self-propelled barge. The result shows there are two cost components very dominant in determining the value of freight with the proportion reaching 90% or even more, namely: time charter hire and fuel cost. Moreover, there are three main factors that have significant impacts on the freight calculation, which are waiting time at ports, time charter rate and fuel oil price.

Performance of a Nonlinear Real-Time Optimal Control System for HEVs/PHEVs during Car Following

Directory of Open Access Journals (Sweden)

Kaijiang Yu

2014-01-01

Full Text Available This paper presents a real-time optimal control approach for the energy management problem of hybrid electric vehicles (HEVs and plug-in hybrid electric vehicles (PHEVs with slope information during car following. The new features of this study are as follows. First, the proposed method can optimize the engine operating points and the driving profile simultaneously. Second, the proposed method gives the freedom of vehicle spacing between the preceding vehicle and the host vehicle. Third, using the HEV/PHEV property, the desired battery state of charge is designed according to the road slopes for better recuperation of free braking energy. Fourth, all of the vehicle operating modes engine charge, electric vehicle, motor assist and electric continuously variable transmission, and regenerative braking, can be realized using the proposed real-time optimal control approach. Computer simulation results are shown among the nonlinear real-time optimal control approach and the ADVISOR rule-based approach. The conclusion is that the nonlinear real-time optimal control approach is effective for the energy management problem of the HEV/PHEV system during car following.

Sensor network design for multimodal freight transportation systems.

Science.gov (United States)

2009-10-15

The agricultural and manufacturing industries in the US Midwest region rely heavily on the efficiency of freight transportation systems. While the growth of freight movement far outpaces that of the transportation infrastructure, ensuring the efficie...

22 CFR 201.67 - Maximum freight charges.

Science.gov (United States)

2010-04-01

..., commodity rate classification, quantity, vessel flag category (U.S.-or foreign-flag), choice of ports, and... the United States. (2) Maximum charter rates. (i) USAID will not finance ocean freight under any... owner(s). (4) Maximum liner rates. USAID will not finance ocean freight for a cargo liner shipment at a...

RETROSPECTIVE ANALYSIS OF FREIGHT CARS REPAIR ORGANIZATION METHODS IN THE DEPOT AND THE WAYS OF THEIR FURTHER DEVELOPMENT

Directory of Open Access Journals (Sweden)

V. V. Myamlin

2010-05-01

Full Text Available A critical analysis of existing methods for repair of freight wagons is presented. The conclusion, that with probability nature of repair activities the “classic” type of a “rigid” production line with regulated step in long-term outlook is inexpedient, has been done. The further development of production-line wagon repair activities is seen in the creation of advanced enterprises equipped with multi-object flexible asynchronous systems with high level of mechanization and automation of technologic processes.

Developing a performance measurement approach to benefit/cost freight project prioritization.

Science.gov (United States)

2014-10-01

Future reauthorizations of the federal transportation bill will require a comprehensive and quantitative analysis of the freight benefits : of proposed freight system projects. To prioritize public investments in freight systems and to insure conside...

49 CFR 230.77 - Foundation brake gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Foundation brake gear. 230.77 Section 230.77... Tenders Brake and Signal Equipment § 230.77 Foundation brake gear. (a) Maintenance. Foundation brake gear...) Distance above the rails. No part of the foundation brake gear of the steam locomotive or tender shall be...

Feasibility of freight villages in the NYMTC region.

Science.gov (United States)

2011-03-23

This report summarizes the work conducted to analyze the site impact of freight villages. The analysis included assessing traffic, : logistics and economic impacts, which are then used to determine the extent to which freight village development has ...

The design of brake fatigue testing system

Directory of Open Access Journals (Sweden)

Huang, Xiaoya

2015-01-01

Full Text Available Brake is used to reduce the operating speed of the machinery equipment or to make it stop. It is essential for vehicles, climbing machines and many fixed equipment in their safety work. Brake tester is an experimental apparatus to measure and analyse the braking performance. Based on the PLC technology and for the purpose of testing brake shoe friction material’s life, this paper designed a virtual brake test platform. In it, inverter were used to control the motor, so that it can load automatically and ensure brake drum constant speed output; what is more, closed loop control system were used to control the brake shoe, so that the cylinder pressure keeps stable in the process of dynamic braking.

The design of aircraft brake systems, employing cooling to increase brake life

Science.gov (United States)

Scaringe, R. P.; Ho, T. L.; Peterson, M. B.

1975-01-01

A research program was initiated to determine the feasibility of using cooling to increase brake life. An air cooling scheme was proposed, constructed and tested with various designs. Straight and curved slotting of the friction material was tested. A water cooling technique, similar to the air cooling procedure, was evaluated on a curved slotted rotor. Also investigated was the possibility of using a phase-change material within the rotor to absorb heat during braking. Various phase-changing materials were tabulated and a 50%, (by weight) LiF - BeF2 mixing was chosen. It was shown that corrosion was not a problem with this mixture. A preliminary design was evaluated on an actual brake. Results showed that significant improvements in lowering the surface temperature of the brake occurred when air or water cooling was used in conjunction with curved slotted rotors.

78 FR 8686 - Establishment of the National Freight Network

Science.gov (United States)

2013-02-06

... includes the National Highway System, freight intermodal connectors, and aerotropolis \\1\\ transportation systems. \\1\\ Aerotropolis transportation systems means a planned and coordinated multimodal freight and...

TOPICAL PROBLEMS AND DEVELOPMENT PERSPECTIVES OF INTERNATIONAL FREIGHT TRANSPORT

OpenAIRE

Sulce, Anastasija

2014-01-01

The title of thesis is Typical Problems and Development Perspectives of International Freight Transport. This work is dedicated to different modes of international transportation, freight and logistics their advantages and disadvantages. Another essential part of the work related to different way for transport development and its efficient usage The objective is to explore modes of freight transport and logistics in details and, thereof, reveal advantages and disadvantages. On the basis ...

Brake blending strategy for a hybrid vehicle

Science.gov (United States)

Boberg, Evan S.

2000-12-05

A hybrid electric powertrain system is provided including a transmission for driving a pair of wheels of a vehicle and a heat engine and an electric motor/generator coupled to the transmission. A friction brake system is provided for applying a braking torque to said vehicle. A controller unit generates control signals to the electric motor/generator and the friction brake system for controllably braking the vehicle in response to a drivers brake command. The controller unit determines and amount of regenerative torque available and compares this value to a determined amount of brake torque requested for determining the control signals to the electric motor/generator and the friction brake system.

49 CFR 1248.1 - Freight commodity statistics.

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Freight commodity statistics. 1248.1 Section 1248... STATISTICS § 1248.1 Freight commodity statistics. All class I railroads, as described in § 1240.1 of this... statistics on the basis of the commodity codes named in § 1248.101. Carriers shall report quarterly on the...

Slowly braked, rotating neutron stars

Science.gov (United States)

Sato, H.

1975-01-01

A slowly braked, rotating neutron star is believed to be a star which rapidly rotates, has no nebula, is nonpulsing, and has a long initial braking time of ten thousand to a million years because of a low magnetic field. Such an object might be observable as an extended weak source of infrared or radio wave radiation due to the scattering of low-frequency strong-wave photons by accelerated electrons. If these objects exist abundantly in the Galaxy, they would act as sources of relatively low-energy cosmic rays. Pulsars (rapidly braked neutron stars) are shown to have difficulties in providing an adequate amount of cosmic-ray matter, making these new sources seem necessary. The possibility that the acceleration mechanism around a slowly braked star may be not a direct acceleration by the strong wave but an acceleration due to plasma turbulence excited by the strong wave is briefly explored. It is shown that white dwarfs may also be slowly braked stars with braking times longer than 3.15 million years.

Load proportional safety brake

Science.gov (United States)

Cacciola, M. J.

1979-01-01

This brake is a self-energizing mechanical friction brake and is intended for use in a rotary drive system. It incorporates a torque sensor which cuts power to the power unit on any overload condition. The brake is capable of driving against an opposing load or driving, paying-out, an aiding load in either direction of rotation. The brake also acts as a no-back device when torque is applied to the output shaft. The advantages of using this type of device are: (1) low frictional drag when driving; (2) smooth paying-out of an aiding load with no runaway danger; (3) energy absorption proportional to load; (4) no-back activates within a few degrees of output shaft rotation and resets automatically; and (5) built-in overload protection.

Compact, Lightweight Servo-Controllable Brakes

Science.gov (United States)

Lovchik, Christopher S.; Townsend, William; Guertin, Jeffrey; Matsuoka, Yoky

2010-01-01

Compact, lightweight servo-controllable brakes capable of high torques are being developed for incorporation into robot joints. A brake of this type is based partly on the capstan effect of tension elements. In a brake of the type under development, a controllable intermediate state of torque is reached through on/off switching at a high frequency.

Railway investigation report : derailment : Canadian National freight train M30351-03 mile 49.4, Edson Subdivision, Wabamun, Alberta, 03 August 2005

International Nuclear Information System (INIS)

2007-01-01

This railway investigation report described an incident in which 43 cars of a Canadian National (CN) freight train derailed near Wabamun, Alberta. The cars contained pole treating oil, toluene, and 700,000 litres of Bunker C heavy oil fuel oil. The accident caused extensive environmental and biological damage to the area, and approximately 20 people were evacuated. This report provided factual information concerning the accident, including details of the railway track and the defect that led to the derailment, as well as details of the CN incident response and remediation process and responses from Alberta Environment. An analysis of the incident examined fatigue limits, defect tracking, and emergency response systems. The report then concluded by examining safety actions taken to ensure improved rail testing, track inspection and maintenance practices. 57 refs., 3 tab., 3 fig

Freight Shuttle System: Cross-Border Movement of Goods

Energy Technology Data Exchange (ETDEWEB)

Levien, Mary

2011-05-31

The Freight Shuttle System (FSS) is designed to provide freight transportation services between those short and intermediate distance locations (within 600 miles) that are currently handling large volumes of freight traffic. Much like trucks, the FSS's transporters are autonomous: each transporter has its own propulsion and travels independently of other transporters. Inspired by railroads, each FSS transporter has steel wheels operating on a steel running surface and can carry either a standardsize freight container or an over-the-road truck trailer. However, unlike either rail or trucks, the FSS runs on an elevated, dedicated guideway to avoid the interference of other transportation systems. The objective of this report is to examine the potential viability for an alternative transportation system for trailers and containers in a multi-national, cross-border setting. The El Paso-Ciudad Juarez region serves as the environment of this analysis.

An Investigation into the Non-bulk Rail Freight Transport in Australia

OpenAIRE

Hadi Ghaderi; Stephen Cahoon; Hong-Oanh Nguyen

2015-01-01

In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market...

Exploratory field trial of motorcycle autonomous emergency braking (MAEB): Considerations on the acceptability of unexpected automatic decelerations.

Science.gov (United States)

Savino, Giovanni; Pierini, Marco; Thompson, Jason; Fitzharris, Michael; Lenné, Michael G

2016-11-16

Autonomous emergency braking (AEB) acts to slow down a vehicle when an unavoidable impending collision is detected. In addition to documented benefits when applied to passenger cars, AEB has also shown potential when applied to motorcycles (MAEB). However, the feasibility of MAEB as practically applied to motorcycles in the real world is not well understood. In this study we performed a field trial involving 16 riders on a test motorcycle subjected to automatic decelerations, thus simulating MAEB activation. The tests were conducted along a rectilinear path at nominal speed of 40 km/h and with mean deceleration of 0.15 g (15% of full braking) deployed at random times. Riders were also exposed to one final undeclared brake activation with the aim of providing genuinely unexpected automatic braking events. Participants were consistently able to manage automatic decelerations of the vehicle with minor to moderate effort. Results of undeclared activations were consistent with those of standard runs. This study demonstrated the feasibility of a moderate automatic deceleration in a scenario of motorcycle travelling in a straight path, supporting the notion that the application of AEB on motorcycles is practicable. Furthermore, the proposed field trial can be used as a reference for future regulation or consumer tests in order to address safety and acceptability of unexpected automatic decelerations on a motorcycle.

Performance of an aircraft tire under cyclic braking and of a currently operational antiskid braking system

Science.gov (United States)

Tanner, J. A.

1972-01-01

An experimental investigation was conducted to study the performance of an aircraft tire under cyclic braking conditions and to study the performance of a currently operational aircraft antiskid braking system. Dry, damp, and flooded runway surface conditions were used in the investigation. The results indicated that under cyclic braking conditions the braking and cornering-force friction coefficients may be influenced by fluctuations in the vertical load, flexibility in the wheel support, and the spring coupling between the wheel and the tire-pavement interface. The cornering capability was shown to be negligible at wheel slip ratios well below a locked-wheel skid under all test surface conditions. The maximum available brake-force friction coefficient was shown to be dependent upon the runway surface condition, upon velocity, and, for wet runways, upon tire differences. Moderate reductions in vertical load and brake system pressure did not significantly affect the overall wet-runway performance of the tire.

Intelligent Braking System using the IR Sensor

OpenAIRE

Gajanan Koli

2017-01-01

Most of the accidents in four wheeled vehicles occur because of failure of braking systems. Manual method of applying brakes is always dangerous as it leads to accidents. Unconsciousness of driver, failure in the linkages of braking systems, road conditions, uncontrollable speed of the vehicle and manual operation of braking systems are the reasons of accidents. It is necessary to control brakes automatically through electronics devices to minimize the accident problems. In this research pape...

Brake wear warning device: A concept

Science.gov (United States)

Hawkins, S. F.

1973-01-01

Heat-insulated wire is introduced through brake shoe and partially into brake lining. Wire is connected to positive terminal and light bulb. When brakes wear to critical point, contact between wire and wheel drum grounds circuit and turns on warning light.

FREIGHTVISION. Sustainable European freight transport 2050. Forecast, vision and policy recommendation

Energy Technology Data Exchange (ETDEWEB)

Helmreich, Stephan [AustriaTech Federal Agency for Technological Measurements Ltd., Wien (Austria). Future of Transport; Keller, Hartmut (eds.) [TransVer GmbH-Transport Research and Consultancy, Muenchen (Germany)

2011-07-01

This book has been written on the basis of the research done between 2008 and 2010 as part of the European Commission funded FREIGHTVISION project. The ''FREIGHTVISION - Freight Transport 2050 Foresight'' project was funded by the Directorate General MOVE to design a long term vision for European freight transport in 2050 and to identify actions and research to progress appropriate freight transport measures in Europe. The project was carried out as a foresight process encompassing four conferences in which the project team identified and developed with the aid of more than 100 experts an action plan for securing long term freight transport in Europe. The book provides insights into the freight transport visions and Backcasts identified for 2035 and 2050, issues which need to be addressed and measures which were assessed to be part of future paths to assure an economical, environmental, and social freight transport system. (orig.)

49 CFR 393.55 - Antilock brake systems.

Science.gov (United States)

2010-10-01

... hydraulic braked vehicles. Each hydraulic braked vehicle subject to the requirements of paragraph (a) of...)). (2) Each air braked commercial motor vehicle other than a truck tractor, manufactured on or after... malfunction circuits and signals for air braked vehicles. (1) Each truck tractor manufactured on or after...

Calculation of freight externality costs for South Africa

Directory of Open Access Journals (Sweden)

Stefaan Swarts

2012-11-01

Full Text Available The purpose of this study is to quantify the marginal external costs associated with freight transport in South Africa. Six cost elements are included as externality cost items, namely, costs related to accidents, emissions, roadway land availability, policing, noise and congestion. Inputs in the calculations were a gravity-oriented freight flow model, a road transport cost model, actual transport costs for other modes, a warehousing cost survey, an inventory delay calculation and various national sources of information such as accident statistics and government budgets. Estimation techniques resulted in advances for externality cost measurement in South Africa. The quantification of the cost elements will be used to update the South African Freight Demand Model. The results show that the cost of transportation would have been 20% more if external factors were taken into account. The marginal rates of externalities can be used to develop scenarios based on alternative choices for South Africa's freight transport infrastructure configuration.

A simulation model for intermodal freight transportation in Louisiana.

Science.gov (United States)

2015-01-01

With increased emphasis on intermodal transportation development, the issue of how to evaluate an intermodal freight transportation system and provide intermodal solutions has been receiving intensive attention. In order to improve freight flow effic...

BASIC STUDY ON TAILORMADE BRAKING SUPPORT SYSTEM

Directory of Open Access Journals (Sweden)

Toshiya HIROSE, M.S.

2004-01-01

This research reviewed the construction of models of a Tailormade Braking Support System (TBSS for braking to stop vehicles and the evaluation of drivers. As a result, the following conclusions were drawn. (1 Braking factors were found to change in the period from the start of braking to stopping; (2 Changes in braking factors can be logically incorporated into the control elements of braking support system; (3 Readymade Driver Model is effective as a model to be incorporated into the base system of TBSS; (4 Tailormade Driver Model built on Neural Network is effective as a main model to construct TBSS; (5 As for TBSS, both subjective and objective ratings on the timing and magnitude of braking are favorable, and its safety and sense of security are improved.

Stand for testing the electrical race car engine

Science.gov (United States)

Baier, M.; Franiasz, J.; Mierzwa, P.; Wylenzek, D.

2015-11-01

An engine test stand created especially for research of electrical race car is described in the paper. The car is an aim of Silesian Greenpower project whose participants build and test electrical vehicles to take part in international races in Great Britain. The engine test stand is used to test and measure the characteristics of vehicles and their engines. It has been designed particularly to test the electric cars engineered by students of Silesian Greenpower project. The article contains a description how the test stand works and shows its versatility in many areas. The paper presents both construction of the test stand, control system and sample results of conducted research. The engine test stand was designed and modified using PLM Siemens NX 8.5. The construction of the test stand is highly modular, which means it can be used both for testing the vehicle itself or for tests without the vehicle. The test stand has its own wheel, motor, powertrain and braking system with second engine. Such solution enables verifying various concepts without changing the construction of the vehicle. The control system and measurement system are realized by enabling National Instruments product myRIO (RIO - Reconfigurable Input/Output). This controller in combination with powerful LabVIEW environment performs as an advanced tool to control torque and speed simultaneously. It is crucial as far as the test stand is equipped in two motors - the one being tested and the braking one. The feedback loop is realized by an optical encoder cooperating with the rotor mounted on the wheel. The results of tests are shown live on the screen both as a chart and as single values. After performing several tests there is a report generated. The engine test stand is widely used during process of the Silesian Greenpower vehicle design. Its versatility enables powertrain testing, wheels and tires tests, thermal analysis and more.

49 CFR 393.40 - Required brake systems.

Science.gov (United States)

2010-10-01

... subpart. (2) Air brake systems. Buses, trucks and truck-tractors equipped with air brake systems and..., and 393.52 of this subpart. (4) Electric brake systems. Motor vehicles equipped with electric brake..., trucks and truck tractors manufactured on or after March 1, 1975, and trailers manufactured on or after...

Brakes Specialist. Teacher Edition. Automotive Service Series.

Science.gov (United States)

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This document contains teacher's materials for a course on becoming an automotive brakes specialist, based on the National Institute of Automotive Service Excellence task lists. The course consists of three instructional units: service brake hydraulic system and wheel bearings, service drum brakes, and service disc brakes. Depending on the…

The dynamics of antilock brake systems

Science.gov (United States)

Denny, Mark

2005-11-01

The nonlinear dynamics of automobile braking are investigated. Nonlinearity arises because of the manner in which the friction coefficient between vehicle tyres and road surface depends upon vehicle speed and wheel angular speed. We show how antilock brake systems approach optimum braking performance.

Wheel slip dump valve for railway braking system

Science.gov (United States)

Zhang, Xuan; Zhang, LiHao; Li, QingXuan; Shi, YanTao

2017-09-01

As we all know, pneumatic braking system plays an important role in the safety of the whole vehicle. In the anti slip braking system, the pressure of braking cylinder can be adjusted by the quick power response of wheel slip dump valve, so that the lock situation won’t occur during vehicle service. During the braking of railway vehicles, the braking force provided by braking disc reduces vehicle’s speed. But the locking slip will happen due to the oversize of braking force or the reduction of sticking coefficient between wheel and rail. It will cause not only the decline of braking performance but also the increase of braking distance. In the meanwhile, it will scratch the wheel and influence the stable running of vehicles. Now, the speed of passenger vehicle has been increased. In order to shorten the braking distance as far as possible, sticking stickiness must be fully applied. So the occurrence probability of wheel slip is increased.

Designing Light Electric Vehicles for urban freight transport

NARCIS (Netherlands)

Balm, S.H.; Hogt, Roeland

2017-01-01

The number of light commercial vehicles (LCV) in cities is growing, which puts increasing pressure on the livability of cities. Freight vehicles are large contributors to polluting air and CO2 emissions and generate problems in terms of safety, noise and loss of public space. Small electric freight

49 CFR 232.407 - Operations requiring use of two-way end-of-train devices; prohibition on purchase of...

Science.gov (United States)

2010-10-01

... a secondary, fully independent braking system capable of safely stopping the train in the event of... either by using the manual toggle switch or through automatic activation, whenever it becomes necessary... automatic brake valve or the conductor's emergency brake valve. (g) En route failure of device on a freight...

Dynamic analysis of elastic rubber tired car wheel breaking under variable normal load

Science.gov (United States)

Fedotov, A. I.; Zedgenizov, V. G.; Ovchinnikova, N. I.

2017-10-01

The purpose of the paper is to analyze the dynamics of the braking of the wheel under normal load variations. The paper uses a mathematical simulation method according to which the calculation model of an object as a mechanical system is associated with a dynamically equivalent schematic structure of the automatic control. Transfer function tool analyzing structural and technical characteristics of an object as well as force disturbances were used. It was proved that the analysis of dynamic characteristics of the wheel subjected to external force disturbances has to take into account amplitude and phase-frequency characteristics. Normal load variations impact car wheel braking subjected to disturbances. The closer slip to the critical point is, the higher the impact is. In the super-critical area, load variations cause fast wheel blocking.

Model-Based Brake Control including Tyre Behaviour

NARCIS (Netherlands)

De Vries, E.J.H.

2012-01-01

The objective of the thesis is to develop a method for controlled braking of a vehicle. The brake pedal depression has been considered to be proportional to the intended deceleration. The brake controller is not aimed to replace a cruise control; it will have an anti-lock braking (ABS) function. The

49 CFR 393.41 - Parking brake system.

Science.gov (United States)

2010-10-01

... system shall, at all times, be capable of being applied by either the driver's muscular effort or by... 49 Transportation 5 2010-10-01 2010-10-01 false Parking brake system. 393.41 Section 393.41... NECESSARY FOR SAFE OPERATION Brakes § 393.41 Parking brake system. (a) Hydraulic-braked vehicles...

Brake for rollable platform

Science.gov (United States)

Morris, A. L.

1974-01-01

Frame-mounted brake is independent of wheels and consists of simple lever-actuated foot. Brake makes good contact with surface even though foot pad is at higher or lower level than wheels, this is particularly important when a rollable platform is used on irregular surface.

Fibre-reinforced ceramics for vehicle brakes; Faserverstaerkte Keramiken fuer Bremsenanwendungen

Energy Technology Data Exchange (ETDEWEB)

Krenkel, W. [DLR Deutsches Zentrum fuer Luft- und Raumfahrt e.V., Stuttgart (Germany). Inst. fuer Bauweisen- und Konstruktionsforschung

2000-07-01

In the context of their aerospace research activities, DLR (Deutsches Zentrum fuer Luft- und Raumfahrt) developed a new process for producing ceramic fibre composite materials that are extremely light and tough. Apart from their applications in aerospace engineering, they have great potential for motor brakes with improved friction and wear characteristics. Excellent results were achieved with the new materials even with conventional brake liners. With customised liners, brake life may be prolonged to match the car life. Further applications are expected in trucks for transport in hazardous materials, high-speed trains, aircraft, industrial machinery and plants, and conveyor systems. [German] Im Rahmen der Raumfahrt-Forschung wurde vom Deutschen Zentrum fuer Luft- und Raumfahrt (DLR) das Fluessigsilicier-Verfahren zur Herstellung von keramischen Verbundwerkstoffen entwickelt. Diese extrem leichten und bruchzaehen Faserkeramiken haben sich unter den besonderen Bedingungen des Weltraums beispielsweise fuer Hitzeschutzstrukturen von Raumfahrzeugen hervorragend bewaehrt. Darueber hinaus zeigten Untersuchungen ein hohes Anwendungspotenzial fuer neue Bremsen mit deutlich verbesserten Reibungs- und Verschleisseigenschaften. Weiterentwicklungen des keramischen Gefueges fuehrten zu innovativen Leichtbau- bzw. Hochleistungs-Bremsen auf der Basis dieser harten und hitzebestaendigen Verbundwerkstoffe. Bereits mit serienmaessigen Bremsbelaegen wurden die heute geltenden Verschleiss- und Reibwertanforderungen teilweise weit uebertroffen. Die Leistungsfaehigkeit heutiger Bremssysteme kann damit deutlich gesteigert und die ungefederte Masse des Fahrwerks drastisch reduziert werden. Mit der zielgerichteten Anpassung geeigneter Belaege auf die neuen Keramik-Bremsscheiben scheint erstmals ein Einsatz von Lebensdauerbremsen moeglich zu sein, deren geringe Verschleissraten einen Austausch der Bremsscheiben waehrend der Betriebszeit eines Fahrzeugs ueberfluessig machen. Neben der

Ontario freight movement study: component two

International Nuclear Information System (INIS)

Hackston, D.; Lake, R.; Schwier, C.; Tardif, L.P.; English, G.; Bunting, M.

1995-11-01

The freight (cargo) transportation sector accounts for a major use of fossil fuels and contributes significantly to greenhouse gas emissions. A study was conducted to assess the prospects, in terms of CO 2 emission reduction, of alternatives to present freight distribution, especially alternatives involving the use of rail instead of truck. Statistical data for Ontario freight transportation were analyzed for fuel consumption, CO 2 emission and cost consequences. Railway fuel consumption was calculated for detailed routing descriptions using a model that computed route and service specific fuel use. The information was compared directly with truck fuel consumption. It was determined that shippers who needed quick, accurately timed shipments preferred trucking over rail, while price conscious shippers, or those with heavy loading commodities preferred rail. An important goal of the study was to identify the enormity of the challenges involved, and clarify the potential tradeoffs by showing different strategies, with respect to CO 2 reduction and related economic impacts. refs., tabs., figs

Development of Anti-lock Braking System (ABS) for Vehicles Braking

OpenAIRE

Minh Vu Trieu; Oamen Godwin; Vassiljeva Kristina; Teder Leo

2016-01-01

This paper develops a real laboratory of anti-lock braking system (ABS) for vehicle and conducts real experiments to verify the ability of this ABS to prevent the vehicle wheel from being locked while braking. Two controllers of PID and fuzzy logic are tested for analysis and comparison. This ABS laboratory is designed for bachelor and master students to simulate and analyze performances of ABS with different control techniques on various roads and load conditions. Thi...

Analysis of a front suspension system for UniART FSAE car using FEA

Science.gov (United States)

Zaidie, M. N. A.; Hashim, M. S. M.; Tasyrif, M.; Basha, M. H.; Ibrahim, I.; Kamaruddin, N. S.; Shahriman, A. B.

2017-10-01

In recent years, many research works from institutions that participated in Formula SAE had highlighted on suspension systems. The aim is to improve the system in term of performance and robustness. However, every suspension system for a racing car is tailored to the car itself. Thus, this paper proposes a new design for front suspension system for UniART FSAE car. The new design was than being compared to the previous suspension system for enhancement. The analysis covered in this paper based on several conditions such as braking, cornering and bumping condition and was carried out using finite element analysis. Each main component for the suspension system such as lower arm, upper arm and knuckle has been analysed in term of strength and performance. From the results, the proposed new design of the suspension system has improved in term of strength and performance compared to the previous suspension system.

Fatigue based design and analysis of wheel hub for Student formula car by Simulation Approach

Science.gov (United States)

Gowtham, V.; Ranganathan, A. S.; Satish, S.; Alexis, S. John; Siva kumar, S.

2016-09-01

In the existing design of Wheel hub used for Student formula cars, the brake discs cannot be removed easily since the disc is mounted in between the knuckle and hub. In case of bend or any other damage to the disc, the replacement of the disc becomes difficult. Further using OEM hub and knuckle that are used for commercial vehicles will result in increase of unsprung mass, which should be avoided in Student formula cars for improving the performance. In this design the above mentioned difficulties have been overcome by redesigning the hub in such a way that the brake disc could be removed easily by just removing the wheel and the caliper and also it will have reduced weight when compared to existing OEM hub. A CAD Model was developed based on the required fatigue life cycles. The forces acting on the hub were calculated and linear static structural analysis was performed on the wheel hub for three different materials using ANSYS Finite Element code V 16.2. The theoretical fatigue strength was compared with the stress obtained from the structural analysis for each material.

Intermodal Logistics Centres and Freight Corridors – Concepts and Trends

Directory of Open Access Journals (Sweden)

Norbert Wagener

2017-09-01

Full Text Available . Background: The development of international freight corridors, as the Trans European Network and new rail and inland shipping corridors in Asia and Africa, require efficient logistics centres along these corridors which serve as intermodal interfaces and provide a variety of different logistics service functions. The definition of the term logistics centre differs between countries and implies different functionalities. Locations are often selected randomly and business models are opportunity driven, especially in highly dynamic and less regulated new emerging economies. In particular Freight Villages as a special form of logistics centres have a high impact on regional development and serve as cargo generator for freight corridors. Consideration of general principles how to establish Freight Villages could improve the effectiveness of these logistics centres along freight corridors. Methods: Based on a literature review a comprehensive and hierarchical definition of logistics centres will be discussed and applied. From experiences in the development of logistics centres in several countries, especially in Germany and Lithuania, challenges and concepts concerning regulatory framework, determination of location and business and financing models are discussed. Results: Concerning the definition of logistics centres a hierarchical definition is applied which comprises different levels of logistics centres depending on the scope of the value adding and the functionality. As general principles for the development of Freight Villages the active role of the state, master planning, objective location finding, participation and co-operation of different stakeholders in the business model and a stepwise scheme for financing are introduced. Major trends for the future development of Freight Villages are the digitalization of supply chains, the application of new intermodal technologies and of innovative telematics systems, solutions for low emission and

Trends in road freight transportation carbon dioxide emissions and policies in China

International Nuclear Information System (INIS)

Li, Hongqi; Lu, Yue; Zhang, Jun; Wang, Tianyi

2013-01-01

We adopted the simple average Divisia index approach to explore the impacts of factors on the carbon dioxide (CO 2 ) emissions from road freight transportation in China from 1985 to 2007. CO 2 emissions were investigated using the following as influencing factors: the emission coefficient, vehicle fuel intensity, working vehicle stock per freight transport operator, market concentration level, freight transportation distance, market share of road freight transportation, ton-kilometer per value added of industry, industrialization level and economic growth. Building on the results, we suggest that economic growth is the most important factor in increasing CO 2 emissions, whereas the ton-kilometer per value added of industry and the market concentration level contribute significantly to decreasing CO 2 emissions. We also discussed some recent important policies concerning factors contained in the decomposition model. - Highlights: ► We estimated road freight fuel consumption and CO 2 emissions in China. ► Factors implying features of road freight were considered in decomposition model. ► Some policies were discussed to affect CO 2 emissions from road freight

Optimal velocity difference model for a car-following theory

International Nuclear Information System (INIS)

Peng, G.H.; Cai, X.H.; Liu, C.Q.; Cao, B.F.; Tuo, M.X.

2011-01-01

In this Letter, we present a new optimal velocity difference model for a car-following theory based on the full velocity difference model. The linear stability condition of the new model is obtained by using the linear stability theory. The unrealistically high deceleration does not appear in OVDM. Numerical simulation of traffic dynamics shows that the new model can avoid the disadvantage of negative velocity occurred at small sensitivity coefficient λ in full velocity difference model by adjusting the coefficient of the optimal velocity difference, which shows that collision can disappear in the improved model. -- Highlights: → A new optimal velocity difference car-following model is proposed. → The effects of the optimal velocity difference on the stability of traffic flow have been explored. → The starting and braking process were carried out through simulation. → The effects of the optimal velocity difference can avoid the disadvantage of negative velocity.

Barriers to and enablers for European rail freight transport for integrated door-to-door logistics service. Part 1: Barriers to multimodal rail freight transport

Directory of Open Access Journals (Sweden)

Dewan Md Zahurul ISLAM

2014-09-01

Full Text Available The objective of this paper is to examine and identify barriers to and enablers for the European rail freight transport services as a transport chain partner along the supply chains in the changing market scenario. The changing market scenario includes, among others, requiring 'door-to-door' rather than 'terminal to terminal' and integrated service, competitive ability to attract non-rail cargo type, changes in the customer requirements (e.g. reliable service and changes in the operational requirements and practices. Using a literature review method, the paper is presented in two parts. The part 1 focuses on the identification of barriers to the European rail freight service by reviewing freight logistics services for global supply chains followed by the current performance of European rail freight transport followed by a discussion on the rail freight market liberalisation in Europe. Then rail freight transport in the Unites States (U.S. is discussed. The research notes that although the background, scope and necessity for reform measures in Europe differ from those of the U.S., some lessons can be learned and the main lesson is that an appropriate reform measure can enhance rail sector competitive ability in Europe. Examining and identifying the barriers in the part 1 (with the pan-Pacific examples of rail freight transports, the part 2 of the paper focuses on recommending clear actions and steps as enablers for the rail freight industry in general and operators in particular. The research in part 1 of the paper finds that: •\tIn many European countries, the rail freight market is not fully liberalised. In such market segment, infrastructure managers do act independently for incumbents and new entrant operators that hamper the progress of building a competitive market; •\tThe rail operators have not yet achieved the service quality (e.g. customer tailored service needed for the modern supply chains; •\tThey operate �

Dreams of pneumatic servo and rail way cars in 2010; 2010 nen noyume kukiatsu servo to tetsudo sharyo

Energy Technology Data Exchange (ETDEWEB)

Sasaki, K. [Tokyo Precision Instruments Co. Ltd., Kanagawa (Japan)

2000-01-15

This paper describes pneumatic servo and railway cars. The comfort of railway cars is improved by reducing excess transverse centrifugal force, and longitudinal, transverse and vertical vibration. Pneumatic system plays a large role in the comfort. Pneumatic system is used for doors because of certain open/shut operation and protecting a hand caught in a door from excess tightening pressure. Pneumatic system is also used for mechanical brakes. Pneumatic spring for car suspensions improves the comfort considerably. The orifice and auxiliary tank of a pneumatic spring reduce a spring constant, and give damping to the vibration system of car bodies and springs. To reduce an outward excess centrifugal force by tilting a car body inward at curve, a body tilting equipment is used which is adopted for a pendulum car with pneumatic servo control, and a tilting car with height control of both side pneumatic springs. For transverse damping, semi-active equipment using oil damper is in wide use, while that using pneumatic servo is also in rial use. (NEDO)

Decomposing road freight energy use in the United Kingdom

International Nuclear Information System (INIS)

Sorrell, Steve; Lehtonen, Markku; Stapleton, Lee; Pujol, Javier; Champion, Toby

2009-01-01

Applying the techniques of decomposition analysis we estimate the relative contribution of ten variables (termed 'key ratios') plus GDP to the change in UK road freight energy use over the period 1989-2004 inclusive. The results are best interpreted as an estimate of the percentage growth in energy consumption that would have resulted from the change in the relevant factor (e.g. length of haul) had the other factors remained unchanged. The results demonstrate that the main factor contributing to the decoupling of UK road freight energy consumption from GDP was the decline in the value of domestically manufactured goods relative to GDP. Over the period 1989-2004 this largely offset the effect of increases in GDP on road freight energy consumption. While the decline in domestic manufacturing was to some extent displaced by increases in imports, the net effect of these supply factors, together with shifts in the commodity mix, has been to reduce UK road freight energy consumption by 30.1%. The net effect on global carbon dioxide (CO 2 ) emissions is likely to be somewhat less beneficial, since many freight movements associated with the manufacture of imported goods have simply been displaced to other countries.

Sustainable freight transport in South Africa:Domestic intermodal solutions

Directory of Open Access Journals (Sweden)

Jan H. Havenga

2011-11-01

Full Text Available Due to the rapid deregulation of freight transport in South Africa two decades ago, and low historical investment in rail (with resultant poor service delivery, an integrated alternative to road and rail competition was never developed. High national freight logistics costs, significant road infrastructure challenges and environmental impact concerns of a road-dominated freight transport market have, however, fuelled renewed interest in intermodal transport solutions. In this article, a high-level business case for domestic intermodal solutions in South Africa is presented. The results demonstrate that building three intermodal terminals to connect the three major industrial hubs (i.e. Gauteng, Durban and Cape Town through an intermodal solution could reduce transport costs (including externalities for the identified 11.5 million tons of intermodalfriendly freight flows on the Cape and Natal corridors by 42% (including externalities.

49 CFR 229.46 - Brakes: General.

Science.gov (United States)

2010-10-01

... regulating all pressures, including but not limited to the automatic and independent brake valves, operate as intended and that the water and oil have been drained from the air brake system. ... 49 Transportation 4 2010-10-01 2010-10-01 false Brakes: General. 229.46 Section 229.46...

An Investigation into the Non-bulk Rail Freight Transport in Australia

Directory of Open Access Journals (Sweden)

Hadi Ghaderi

2015-03-01

Full Text Available In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market has declined significantly in the last four decades. This study therefore provides an insight into the efficiency and operational management issues facing by the Australian non-bulk rail sector by focusing on three areas; the level of track compatibility and the relevant operational issues, the demographics of non-bulk freight in Australia and the current status of intermodal terminals in relation to rail connectivity and location. As the result, a more detailed understanding of the current shortages in the Australian non-bulk rail freight sector is achieved and managerial implications are provided.

Estimation of Road Friction Coefficient in Different Road Conditions Based on Vehicle Braking Dynamics

Science.gov (United States)

Zhao, You-Qun; Li, Hai-Qing; Lin, Fen; Wang, Jian; Ji, Xue-Wu

2017-07-01

The accurate estimation of road friction coefficient in the active safety control system has become increasingly prominent. Most previous studies on road friction estimation have only used vehicle longitudinal or lateral dynamics and often ignored the load transfer, which tends to cause inaccurate of the actual road friction coefficient. A novel method considering load transfer of front and rear axles is proposed to estimate road friction coefficient based on braking dynamic model of two-wheeled vehicle. Sliding mode control technique is used to build the ideal braking torque controller, which control target is to control the actual wheel slip ratio of front and rear wheels tracking the ideal wheel slip ratio. In order to eliminate the chattering problem of the sliding mode controller, integral switching surface is used to design the sliding mode surface. A second order linear extended state observer is designed to observe road friction coefficient based on wheel speed and braking torque of front and rear wheels. The proposed road friction coefficient estimation schemes are evaluated by simulation in ADAMS/Car. The results show that the estimated values can well agree with the actual values in different road conditions. The observer can estimate road friction coefficient exactly in real-time and resist external disturbance. The proposed research provides a novel method to estimate road friction coefficient with strong robustness and more accurate.

Vieweg manual of motor car engineering. 3. tot. new rev. and enl. ed.; Vieweg Handbuch Kraftfahrzeugtechnik

Energy Technology Data Exchange (ETDEWEB)

Braess, H.H.; Seiffert, U. (eds.)

2003-07-01

This is the 3rd, revised and re-edited edition. Current trends are considered, i.e. DI and variable valve operation, particulate filters, double clutch gears, ESP-Plus, SUN-Fuel, and variable adaptive lighting. There are new chapters on standardisation (e.g. telematics and interface problems), accident research, internals, software, service-friendly design, maintenance and diagnosis, as well as sports and racing cars. Contents: Requirements on motor cars; Innovative technologies; Aerodynamics; Air conditioning; Acoustics; Design; Package; Fuel cell; Electric vehicles; Gas turbine; Spark ignition engine; Diesel engine; Superchargers; Couplings and gears; Four-wheel drives; Brakes and control systems; Two-stroke engines; Car bodies; Materials; Surface protection; Passenger compartment; Safety; Brakes; Tyres; Chassis; Fuels; Electric and electronic systems; Software; Driver assistant systems; Lighting; Sensors; Onboard network; EMP; Materials; Simultaneous engineering; Simulations; Experimental technologies; Motor cars and transportation in the future; Legislation and standardisation; Accident research; Diagnosis and maintenance; Racing cars and sports cars. [German] Fahrzeugingenieure in Praxis und Ausbildung benoetigen den raschen und sicheren Zugriff auf Grundlagen und Details der Fahrzeugtechnik sowie wesentliche zugehoerige industrielle Prozesse. Solche Informationen, die in ganz unterschiedlichen Quellen abgelegt sind, systematisch und bewertend zusammenzufuehren, hat sich dieses Handbuch zum Ziel gesetzt. Die Autoren sind bedeutende Fachleute der deutschen Automobil- und Zuliefererindustrie, sie stellen sicher, dass Theorie und Praxis vernetzt vermittelt werden. Die dritte Auflage wurde neu bearbeitet, aktualisiert und erweitert. Damit haben die aktuellen Entwicklungen von Benzindirekteinspritzung und variabler Ventilbetrieb, sowie Partikelfilter, Doppelkupplungsgetriebe, ESP-Plus, SUN-Fuel oder variable adaptive Beleuchtungssysteme Eingang gefunden. Neu

49 CFR 236.712 - Brake pipe.

Science.gov (United States)

2010-10-01

... OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.712 Brake pipe. A pipe running from the engineman's brake valve through the train, used for the transmission of air under... 49 Transportation 4 2010-10-01 2010-10-01 false Brake pipe. 236.712 Section 236.712 Transportation...

49 CFR 238.431 - Brake system.

Science.gov (United States)

2010-10-01

.... (e) The following requirements apply to blended braking systems: (1) Loss of power or failure of the... adhesion control system designed to automatically adjust the braking force on each wheel to prevent sliding during braking. In the event of a failure of this system to prevent wheel slide within preset parameters...

Integrating passenger and freight transportation : model formulation and insights

NARCIS (Netherlands)

Ghilas, V.; Demir, E.; Woensel, van T.

2013-01-01

Integrating passenger and freight ows creates attractive business opportunities because the same transportation needs can be met with fewer vehicles and emissions. This paper seeks an integrated solution for the transportation of passenger and freight simultaneously, so that fewer vehicles are

Pentiptycene-derived light-driven molecular brakes: substituent effects of the brake component.

Science.gov (United States)

Sun, Wei-Ting; Huang, Yau-Ting; Huang, Guan-Jhih; Lu, Hsiu-Feng; Chao, Ito; Huang, Shou-Ling; Huang, Shing-Jong; Lin, Ying-Chih; Ho, Jinn-Hsuan; Yang, Jye-Shane

2010-10-11

Five pentiptycene-derived stilbene systems (1 R; R = H, OM, NO, Pr, and Bu) have been prepared and investigated as light-driven molecular brakes that have different-sized brake components (1 Hbrake component in the trans form ((E)-1 R), which corresponds to the brake-off state. When the brake is turned on by photoisomerization to the cis form ((Z)-1 R), the pentiptycene rotation can be arrested on the NMR spectroscopic timescale at temperatures that depend on the brake component. In the cases of (Z)-1 NO, (Z)-1 Pr, and (Z)-1 Bu, the rotation is nearly blocked (k(rot)=2-6 s(-1)) at 298 K. It is also demonstrated that the rotation is slower in [D(6)]DMSO than in CD(2)Cl(2). A linear relationship between the free energies of the rotational barrier and the steric parameter A values is present only for (Z)-1 H, (Z)-1 OM, and (Z)-1 NO, and it levels off on going from (Z)-1 NO to (Z)-1 Pr and (Z)-1 Bu. DFT calculations provide insights into the substituent effects in the rotational ground and transition states. The molar reversibility of the E-Z photoswitching is up to 46%, and both the E and Z isomers are stable under the irradiation conditions. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Vehicle brake testing system

Science.gov (United States)

Stevens, Samuel S [Harriman, TN; Hodgson, Jeffrey W [Lenoir City, TN

2002-11-19

This invention relates to a force measuring system capable of measuring forces associated with vehicle braking and of evaluating braking performance. The disclosure concerns an invention which comprises a first row of linearly aligned plates, a force bearing surface extending beneath and beside the plates, vertically oriented links and horizontally oriented links connecting each plate to a force bearing surface, a force measuring device in each link, a transducer coupled to each force measuring device, and a computing device coupled to receive an output signal from the transducer indicative of measured force in each force measuring device. The present invention may be used for testing vehicle brake systems.

FREIGHT CONTAINER LIFTING STANDARD

Energy Technology Data Exchange (ETDEWEB)

POWERS DJ; SCOTT MA; MACKEY TC

2010-01-13

This standard details the correct methods of lifting and handling Series 1 freight containers following ISO-3874 and ISO-1496. The changes within RPP-40736 will allow better reading comprehension, as well as correcting editorial errors.

Emergency Braking of a Mine Hoist in the Context of the Braking System Selection

Science.gov (United States)

Wolny, Stanisław

2017-03-01

The paper addresses the selected aspects of the dynamic behaviour of mine hoists during the emergency braking phase. Basing on the model of the hoist and supported by theoretical backgrounds provided by the author (Wolny, 2016), analytical formulas are derived to determine the parameters of the braking system such that during an emergency braking it should guarantee that: - the maximal loading of the hoisting ropes should not exceed the rope breaking force, - deceleration of the conveyances being stopped should not exceed the admissible levels Results of the dynamic analysis of the mine hoist behaviour during an emergency braking phase summarised in this study can be utilised to support the design of conveyance and rope attachments by the fatigue endurance methods, with an aim to adapt it to the specified operational parameters of the hoisting installation (Eurokod 3).

Biodegradability of unused lubricating brake fluids in fresh and ...

African Journals Online (AJOL)

The biodegradability of four unused lubricating brake fluids (Total brake fluid, Allied brake fluid, Oando brake fluid and Ate brake fluid) was carried out in fresh and marine water obtained from Isiokpo stream and Bonny river of the Niger Delta, South South Nigeria. Biodegradability, of the brake fluids were obtained after a 56 ...

Statistical analysis of brake squeal noise

Science.gov (United States)

Oberst, S.; Lai, J. C. S.

2011-06-01

Despite substantial research efforts applied to the prediction of brake squeal noise since the early 20th century, the mechanisms behind its generation are still not fully understood. Squealing brakes are of significant concern to the automobile industry, mainly because of the costs associated with warranty claims. In order to remedy the problems inherent in designing quieter brakes and, therefore, to understand the mechanisms, a design of experiments study, using a noise dynamometer, was performed by a brake system manufacturer to determine the influence of geometrical parameters (namely, the number and location of slots) of brake pads on brake squeal noise. The experimental results were evaluated with a noise index and ranked for warm and cold brake stops. These data are analysed here using statistical descriptors based on population distributions, and a correlation analysis, to gain greater insight into the functional dependency between the time-averaged friction coefficient as the input and the peak sound pressure level data as the output quantity. The correlation analysis between the time-averaged friction coefficient and peak sound pressure data is performed by applying a semblance analysis and a joint recurrence quantification analysis. Linear measures are compared with complexity measures (nonlinear) based on statistics from the underlying joint recurrence plots. Results show that linear measures cannot be used to rank the noise performance of the four test pad configurations. On the other hand, the ranking of the noise performance of the test pad configurations based on the noise index agrees with that based on nonlinear measures: the higher the nonlinearity between the time-averaged friction coefficient and peak sound pressure, the worse the squeal. These results highlight the nonlinear character of brake squeal and indicate the potential of using nonlinear statistical analysis tools to analyse disc brake squeal.

New technical solutions of using rolling stock electrodynamical braking

Directory of Open Access Journals (Sweden)

Leonas Povilas LINGAITIS

2009-01-01

Full Text Available The paper considers some theoretical and practical problems associated with the use of traction motor are operating in the generator mode (in braking. Mathematical and graphical relationships of electrodynamic braking, taking into account the requirements raised to braking systems in rail transport are presented. The latter include discontinuity of braking process, braking force regulation, depending on the locomotive speed, mass, type of railway and other parameters. Schematic diagrams of the locomotive braking and ways of controlling the braking force by varying electric circuit parameters are presented. The authors suggested contact-free regulation method of braking resistor for controlling braking force in rheostatic braking, and resistor parameters regulate with pulse regulation mode by semiconductor devices, such as new electrical components for rolling stock – IGBT transistors operating in the key mode. Presenting energy savings power systems, which are using regenerative braking-returning energy and diesel engine or any form of hybrid traction vehicles systems, circuit diagrams, electrical parameters curves.

49 CFR 570.57 - Air brake system and air-over-hydraulic brake subsystem.

Science.gov (United States)

2010-10-01

... the drain cocks in the service and supply reservoir on the truck or truck-tractor. Note the pressure.... Close the drain cocks, and, with the trailer(s) uncoupled, check air pressure buildup at the... brakes fully applied. (b) Air brake system hoses, tubes and connections. Air system tubes, hoses and...

On structural inelasticity of modal substitution in freight transport

DEFF Research Database (Denmark)

Rich, Jeppe; Kveiborg, Ole; Overgård, Christian Hansen

2011-01-01

alternative available. The paper investigates the magnitude of this ‘‘structural inelasticity” of modal substitution in freight transport due to a sparser layout of rail and ship-based freight networks compared to road. In the analysis we use a recent Scandinavian freight demand model covering more than 800...... zones. We find that the structural inelasticity is very significant – in particular for transportation over less than 500 km. Moreover, the inelasticity varies greatly with commodity groups and between OD pairs, and it depends strongly on the port and rail infrastructure. The results suggest that pure...

75 FR 8180 - Proposed Agency Information Collection Activities; Comment Request

Science.gov (United States)

2010-02-23

... freight cars. Railroads are required to inspect freight cars for compliance and to determine restrictions on the movements of defective cars. Annual Estimated Burden: 40 hours. Title: Passenger Train... minimize the burden of the collections of information on respondents, including the use of automated...

Study on Abrasive Wear of Brake Pad in the Large-megawatt Wind Turbine Brake Based on Deform Software

Science.gov (United States)

Zhang, Shengfang; Hao, Qiang; Sha, Zhihua; Yin, Jian; Ma, Fujian; Liu, Yu

2017-12-01

For the friction and wear issues of brake pads in the large-megawatt wind turbine brake during braking, this paper established the micro finite element model of abrasive wear by using Deform-2D software. Based on abrasive wear theory and considered the variation of the velocity and load in the micro friction and wear process, the Archard wear calculation model is developed. The influence rules of relative sliding velocity and friction coefficient in the brake pad and disc is analysed. The simulation results showed that as the relative sliding velocity increases, the wear will be more serious, while the larger friction coefficient lowered the contact pressure which released the wear of the brake pad.

Implementation of advanced technologies and other means in dangerous freight transportation

Directory of Open Access Journals (Sweden)

N. Batarlienė

2007-12-01

Full Text Available This article examines types of modern technologies application possibilities in dangerous freight transportation. It is noted that the solution to transport technology problems is based on the improvement of technological supply, the rational usage of informational modeling methodology of the whole transportation process. The aspects of mobile solution of public information and transport are named in this paper. The article presents concrete vehicles and freight tracking on their trips analysis, the principles and methods of their operation. Tracking and localization systems are playing a great role in the transportation of dangerous freight. The newly developed remote identification system for transport facilities and freight are presented.

THE IMPACT OF INFORMATION AND COMMUNICATION TECHNOLOGY ON ROAD FREIGHT TRANSPORTATION

Directory of Open Access Journals (Sweden)

Ryuichi YOSHIMOTO

2005-01-01

Full Text Available Surveying the recent trend toward e-commerce and computerization in the trucking industry, this paper establishes a framework for analyzing the impact of information and communication technology on road freight transportation in terms of commerce, logistics and fleet management, and proposes hypothetical mechanisms of influence. The authors note that the rapid growth of e-commerce and freight fleet management systems make it difficult to arrive at firm, statistics-based conclusions about their impact on road freight transportation, but suggest that more sophisticated government management of transportation demand as well as freight fleet management systems could cancel out the negative impact of e-commerce on road transportation.

Adaptive controller for regenerative and friction braking system

Science.gov (United States)

Davis, Roy I.

1990-01-01

A regenerative and friction braking system for a vehicle having one or more roadwheels driven by an electric traction motor includes a driver responsive device for producing a brake demand signal having a magnitude corresponding to the level of braking force selected by the driver and friction and regenerative brakes operatively connected with the roadwheels of the vehicle. A system according to this invention further includes control means for operating the friction and regenerative braking subsystems so that maximum brake torques sustainable by the roadwheels of the vehicle without skidding or slipping will not be exceeded.

Recent studies of tire braking performance. [for aircraft

Science.gov (United States)

Mccarty, J. L.; Leland, T. J. W.

1973-01-01

The results from recent studies of some factors affecting tire braking and cornering performance are presented together with a discussion of the possible application of these results to the design of aircraft braking systems. The first part of the paper is concerned with steady-state braking, that is, results from tests conducted at a constant slip ratio or steering angle or both. The second part deals with cyclic braking tests, both single cycle, where brakes are applied at a constant rate until wheel lockup is achieved, and rapid cycling of the brakes under control of a currently operational antiskid system.

STUDY OF TECHNICAL STATE IMPACT OF BRAKE RETARDERS AT THE PROCESSING ABILITY OF HUMPS

Directory of Open Access Journals (Sweden)

D. M. Kozachenko

2016-08-01

Full Text Available Purpose. The research aims development of methods for calculating the estimated capacity humps for the loss conditions of brake power retarders. Methodology. The operation of humps is connected with large number of random factors, such as the characteristics of cuts, environmental conditions, the value of braking power implemented by retardants and others. In this regard, to research the set tasks the methods of simulation modeling and mathematical statistics are used. Determination of speed and motion time of cuts on the routes is carried out on the basis of rolling down modeling of their rolling down from the humps. Findings. If the brake power of retarders of the rolling down part of humps is not enough to stop the cuts, it should be provided the intervals during break-up to release the rolling routes from the preliminary cuts. The dependencies allowing to set the duration of these intervals were determined using the methods of the probability theory If the brake power of retarders at the rolling down part of humps and at the classification tracks is not enough to meet the requirements of the aimed regulation of the cuts rolling speed, it is necessary the use the additional brake shoes. The work develops the methods that on the basis of simulation modeling of the humping process allow one to set the desired value of the break-up duration increase. They ensure the traffic safety at the given number of car motion speed regulators. Originality. Authors firstly proposed the improved methods for determining the estimated capacity of humps. Unlike the existing ones, allow taking into account the technological limitations caused by the requirements of the humping process safety and can be used to assess the performance of the humps in the conditions of parametric failures of the retarders. Practical value. The use of the proposed methods allows assessing the influence of the retarders’ disrepair on the performance degradation of humps for the

Feedback brake distribution control for minimum pitch

Science.gov (United States)

Tavernini, Davide; Velenis, Efstathios; Longo, Stefano

2017-06-01

The distribution of brake forces between front and rear axles of a vehicle is typically specified such that the same level of brake force coefficient is imposed at both front and rear wheels. This condition is known as 'ideal' distribution and it is required to deliver the maximum vehicle deceleration and minimum braking distance. For subcritical braking conditions, the deceleration demand may be delivered by different distributions between front and rear braking forces. In this research we show how to obtain the optimal distribution which minimises the pitch angle of a vehicle and hence enhances driver subjective feel during braking. A vehicle model including suspension geometry features is adopted. The problem of the minimum pitch brake distribution for a varying deceleration level demand is solved by means of a model predictive control (MPC) technique. To address the problem of the undesirable pitch rebound caused by a full-stop of the vehicle, a second controller is designed and implemented independently from the braking distribution in use. An extended Kalman filter is designed for state estimation and implemented in a high fidelity environment together with the MPC strategy. The proposed solution is compared with the reference 'ideal' distribution as well as another previous feed-forward solution.

Development of Anti-lock Braking System (ABS) for Vehicles Braking

Science.gov (United States)

Minh, Vu Trieu; Oamen, Godwin; Vassiljeva, Kristina; Teder, Leo

2016-11-01

This paper develops a real laboratory of anti-lock braking system (ABS) for vehicle and conducts real experiments to verify the ability of this ABS to prevent the vehicle wheel from being locked while braking. Two controllers of PID and fuzzy logic are tested for analysis and comparison. This ABS laboratory is designed for bachelor and master students to simulate and analyze performances of ABS with different control techniques on various roads and load conditions. This paper provides educational theories and practices on the design of control for system dynamics.

Basic freight forwarding and transport
 documentation in freight forwarder’s work

Directory of Open Access Journals (Sweden)

Adam Salomon

2014-09-01

Full Text Available The purpose of the article is to present the basic documentation in international freight forwarder’s work, in particular, insurance documents and transport documents in various modes of transport. An additional goal is to identify sources of the paper, which can be used to properly completing the individual documents.

Eye Carduino: A Car Control System using Eye Movements

Science.gov (United States)

Kumar, Arjun; Nagaraj, Disha; Louzardo, Joel; Hegde, Rajeshwari

2011-12-01

Modern automotive systems are rapidly becoming highly of transportation, but can be a web integrated media centre. This paper explains the implementation of a vehicle control defined and characterized by embedded electronics and software. With new technologies, the vehicle industry is facing new opportunities and also new challenges. Electronics have improved the performance of vehicles and at the same time, new more complex applications are introduced. Examples of high level applications include adaptive cruise control and electronic stability programs (ESP). Further, a modern vehicle does not have to be merely a means using only eye movements. The EyeWriter's native hardware and software work to return the co-ordinates of where the user is looking. These co-ordinates are then used to control the car. A centre-point is defined on the screen. The higher on the screen the user's gaze is, the faster the car will accelerate. Braking is done by looking below centre. Steering is done by looking left and right on the screen.

Elastoplastic finite element analysis for wet multidisc brake during lasting braking

Directory of Open Access Journals (Sweden)

Ji Zhanling

2015-01-01

Full Text Available Addressed to serious heat degradation problem of the braking continuously performed in the drag brake application for a long time, finite element analysis for bidirectional thermal-structure coupling is adopted to investigate temperature and stress when material properties are temperature-dependent. Based on the constitutive relations of heat transfer and strain-stress, three-dimensional transient finite element equilibrium equations with many kinds of boundary conditions for bidirectional thermal-structure coupling were derived. And it was originally presented that start time, location, severity and evolution laws of plastic deformation were depicted using dimensionless stress distribution contour with the yield limit related to temperature. The change laws of plastic element number and contact area versus braking time were expressed by plasticity ratio and contact ratio curves, respectively. The laws revealed by the numerical calculation results are in accordance with the objective perception and reasoning.

Mountain Plains Learning Experience Guide: Automotive Repair. Course: Brake Systems.

Science.gov (United States)

Schramm, C.; Osland, Walt

One of twelve individualized courses included in an automotive repair curriculum, this course covers theory, operation, and repair of drum brakes, disc brakes, and brake system components. The course is comprised of six units: (1) Fundamentals of Brake Systems, (2) Master Cylinder, (3) Drum Brakes, (4) Disc Brakes, (5) Power Brakes, and (6)…

Friction brake cushions acceleration and vibration loads

Science.gov (United States)

Fraser, G. F.; Zawadski, G. Z.

1966-01-01

Friction brake cushions an object in a vehicle from axially applied vibration and steady-state acceleration forces. The brake incorporates a doubly tapered piston that applies a controlled radial force to friction brake segments bearing against the walls of a cylinder.

49 CFR 236.701 - Application, brake; full service.

Science.gov (United States)

2010-10-01

... a split reduction in brake pipe pressure at a service rate until maximum brake cylinder pressure is developed. As applied to an automatic or electro-pneumatic brake with speed governor control, an application other than emergency which develops the maximum brake cylinder pressure, as determined by the design of...

Cars, Cars, Cars

Science.gov (United States)

McIntosh, Phyllis

2013-01-01

Cars are the focus of this feature article, which explores such topics as the history of cars in the United States, the national highway system, safety and pollution concerns, mobility and freedom for women, classic car shows, and the road trip in American literature and film. Also included are links to the websites of Automobile in American Life…

REGRESSIVE ANALYSIS OF BRAKING EFFICIENCY OF M1 CATEGORY VEHICLES WITH ANTI-BLOCKING BRAKE SYSTEM

Directory of Open Access Journals (Sweden)

О. Sarayev

2015-07-01

Full Text Available The problematics of assessing the effectiveness of vehicle braking after road accidentoccurrence is considered. For the first time in relation to the modern models of vehicles equipped with anti-lock brakes there were obtained regression models describing the relationship between the coefficient of traction and a random variable of steady deceleration. This does not contradict the essence of the stochastic physical object, which is the process of vehicle braking, unlike the previously adopted method of formalizing this process, using a deterministic function.

Design of a magnetic braking system

International Nuclear Information System (INIS)

Jou, M.; Shiau, J.-K.; Sun, C.-C.

2006-01-01

A non-contact method, using magnetic drag force principle, was proposed to design the braking systems to improve the shortcomings of the conventional braking systems. The extensive literature detailing all aspects of the magnetic braking is briefly reviewed, however little of this refers specifically to upright magnetic braking system, which is useful for industries. One of the major issues to design upright magnetic system is to find out the magnetic flux. The changing magnetic flux induces eddy currents in the conductor. These currents dissipate energy in the conductor and generate drag force to slow down the motion. Therefore, a finite element model is developed to analyze the phenomena of magnetic flux density when air gap and materials of track are varied. The verification shows the predicted magnetic flux is within acceptable range with the measured value. The results will facilitate the design of magnetic braking systems

Thermal Characterisation of Brake Pads

DEFF Research Database (Denmark)

Ramousse, Séverine; Høj, Jakob Weiland; Sørensen, O. T.

2001-01-01

The chemical-physical decomposition processes that occur in a brake pad heated to 1000degreesC have been studied. This temperature can be reached when a brake pad is applied. Thermogravimetry and differential thermal analysis were used in combination with evolved gas analysis, and image analysis...... using a scanning electron microscope.A brake pad is essentially a mixture of iron, carbon and binder. Combined techniques have been used, because of chemical reaction overlap, to determine how and at what temperature the binder decomposes, the coal and graphite combust and the iron oxidises.This work...

Adjustable Tooling for Bending Brake

Science.gov (United States)

Ellis, J. M.

1986-01-01

Deep metal boxes and other parts easily fabricated. Adjustable tooling jig for bending brake accommodates spacing blocks and either standard male press-brake die or bar die. Holds spacer blocks, press-brake die, bar window die, or combination of three. Typical bending operations include bending of cut metal sheet into box and bending of metal strip into bracket with multiple inward 90 degree bends. By increasing free space available for bending sheet-metal parts jig makes it easier to fabricate such items as deep metal boxes or brackets with right-angle bends.

Safety brake for tape reels

Science.gov (United States)

Carle, C. E.

1977-01-01

All-mechanical device senses end of tape and stops reel, even in event of electronic system failure. Assembly includes stop to prevent brake from overriding tape. Recentering mechanism returns brake to neutral position after torque is removed from reels.

Backup Mechanical Brake System of the Wind Turbine

Science.gov (United States)

Sirotkin, E. A.; Solomin, E. V.; Gandzha, S. A.; Kirpichnikova, I. M.

2018-01-01

Paper clarifies the necessity of the emergency mechanical brake systems usage for wind turbines. We made a deep analysis of the wind turbine braking methods available on the market, identifying their strengths and weaknesses. The electromechanical braking appeared the most technically reasonable and economically attractive. We described the developed combined electromechanical brake system for vertical axis wind turbine driven from electric drive with variable torque enough to brake over the turbine even on the storm wind speed up to 45 m/s. The progress was made due to the development of specific kinematic brake system diagram and intelligent control system managed by special operation algorithm.

Development of a Freight Demand Model with an Application to California

Directory of Open Access Journals (Sweden)

Robert Lim

2014-03-01

Full Text Available This paper discusses the disaggregation of the Federal Highway Administration's Freight Analysis Framework (FAF database (version 3.0 on freight origin-destination data and the development of linear regression equations to describe the relationships between commodity-based freight trip productions/attractions to specific economic variables. Instead of generating a production/attraction equation for each commodity, commodities are grouped in certain ways to simplify model development and application. We consider three grouping methods and two model selection criteria (with and without intercepts, which are compared in terms of goodness of fit with two data sets (FAF versions 2.0 and 3.0. Furthermore, the freight generation models are validated using county-level economic data in California and applied to predict year 2015 commodity outputs. The results of this study can help city, county, metropolitan and state level planning agencies develop their own customized freight demand generation models without performing costly large-scale surveys.

Uncovering Document Fraud in Maritime Freight Transport Based on Probabilistic Classification

OpenAIRE

Triepels , Ron; Feelders , Ad; Daniels , Hennie

2015-01-01

Part 4: Data Analysis and Information Retrieval; International audience; Deficient visibility in global supply chains causes significant risks for the customs brokerage practices of freight forwarders. One of the risks that freight forwarders face is that shipping documentation might contain document fraud and is used to declare a shipment. Traditional risk controls are ineffective in this regard since the creation of shipping documentation is uncontrollable by freight forwarders. In this pap...

Fatal accidental inhalation of brake cleaner aerosols.

Science.gov (United States)

Veit, F; Martz, W; Birngruber, C G; Dettmeyer, R B

2018-04-23

Brake cleaner liquid is commonly used for cleaning of engines and motor parts. The commercially available products usually contain mainly volatile organic compounds. As a consequence brake cleaner evaporates fast and almost completely from the cleaned surface. This case report presents a fatal accidental inhalation of brake cleaner liquid aerosols due to the attempted cleaning of a boat engine. A 16year old boy was found lifeless in the engine compartment of a boat engine. In close proximity to the body, the police found cleanings wipes soaked with brake cleaner as well as a pump spray bottle filled with brake cleaner. Essentially the autopsy revealed a cerebral oedema with encephalomalacia, no coagulated blood as well as increased blood and tissue fluid content of the lung. Toxicological analysis revealed brake cleaner fluid in the lung, gastric content and heart blood. Copyright © 2018 Elsevier B.V. All rights reserved.

Transportation Energy Futures Series: Freight Transportation Demand: Energy-Efficient Scenarios for a Low-Carbon Future

Energy Technology Data Exchange (ETDEWEB)

Grenzeback, L. R. [Cambridge Systematics Inc., Cambridge, MA (United States); Brown, A. [Cambridge Systematics Inc., Cambridge, MA (United States); Fischer, M. J. [Cambridge Systematics Inc., Cambridge, MA (United States); Hutson, N. [Cambridge Systematics Inc., Cambridge, MA (United States); Lamm, C. R. [Cambridge Systematics Inc., Cambridge, MA (United States); Pei, Y. L. [Cambridge Systematics Inc., Cambridge, MA (United States); Vimmerstedt, L. [Cambridge Systematics Inc., Cambridge, MA (United States); Vyas, A. D. [Cambridge Systematics Inc., Cambridge, MA (United States); Winebrake, J. J. [Cambridge Systematics Inc., Cambridge, MA (United States)

2013-03-01

Freight transportation demand is projected to grow to 27.5 billion tons in 2040, and by extrapolation, to nearly 30.2 billion tons in 2050, requiring ever-greater amounts of energy. This report describes the current and future demand for freight transportation in terms of tons and ton-miles of commodities moved by truck, rail, water, pipeline, and air freight carriers. It outlines the economic, logistics, transportation, and policy and regulatory factors that shape freight demand; the possible trends and 2050 outlook for these factors, and their anticipated effect on freight demand and related energy use. After describing federal policy actions that could influence freight demand, the report then summarizes the available analytical models for forecasting freight demand, and identifies possible areas for future action.

49 CFR 393.43 - Breakaway and emergency braking.

Science.gov (United States)

2010-10-01

... ACCESSORIES NECESSARY FOR SAFE OPERATION Brakes § 393.43 Breakaway and emergency braking. (a) Towing vehicle protection system. Every motor vehicle, if used to tow a trailer equipped with brakes, shall be equipped with... brake systems installed on towed vehicles shall be so designed, by the use of “no-bleed-back” relay...

Indonesian commercial bus drum brake system temperature model

International Nuclear Information System (INIS)

Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

2016-01-01

Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

Indonesian commercial bus drum brake system temperature model

Science.gov (United States)

Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

2016-03-01

Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

Indonesian commercial bus drum brake system temperature model

Energy Technology Data Exchange (ETDEWEB)

Wibowo, D. B., E-mail: rmt.bowo@gmail.com; Haryanto, I., E-mail: ismoyo2001@yahoo.de; Laksono, N. P., E-mail: priyolaksono89@gmail.com [Mechanical Engineering Dept., Faculty of Engineering, Diponegoro University (Indonesia)

2016-03-29

Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

Implementation of object-oriented programming in study of electrical race car

Science.gov (United States)

Nowak, M.; Baier, M.

2016-08-01

The paper covers issue of conducting advanced research of electrical race car participating in international competition called Sileverline Corporate Challenge. Process of designing race cars in Silesian Greenpower team is aided by a professional engine test stand built particularly in purpose of this research. Phase of testing and simulation is an important part of the implementation of new technologies. Properly developed solutions and test procedures are able to significantly shorten development time and reduce design costs. Testing process must be controlled by a modular and flexible application, easy to modify and ensuring safety. This paper describes the concept of object-oriented programming in LabVIEW and exemplary architecture of object-oriented control application designed to control engine test stand of the electrical race car. Eventually, the task of application will be to steer the electromagnetic brake and the engine load torque to perform according to data from the actual race track. During the designing process of the car, minimizing energy losses and maximizing powertrain efficiency are the main aspects taken into consideration. One of the crucial issues to accomplish these goals is to maintain optimal performance of the motor by applying effective cooling. The paper covers the research verifying the effectiveness of the cooling system.

Development of a multi-pole magnetorheological brake

International Nuclear Information System (INIS)

Shiao, Yaojung; Nguyen, Quang-Anh

2013-01-01

This paper presents a new approach in the design and optimization of a novel multi-pole magnetorheological (MR) brake that employs magnetic flux more effectively on the surface of the rotor. MR brakes with conventional single ring-type electromagnetic poles have reached the limits of torque enhancement. One major reason is the limitation of the magnetic field strength within the active area of the MR fluid due to the geometric constraints of the coil. The multi-pole MR brake design features multiple electromagnetic poles surrounded by several coils. As a result, the active chaining areas for the MR fluid are greatly increased, and significant brake torque improvement is achieved. The coil structure, as a part of the stator, becomes flexible and customizable in terms of space usage for the winding and bobbin design. In addition, this brake offers extra options in its dimensions for torque enhancement because either the radial or the axial dimensions of the rotor can be increased. Magnetic circuit analysis was conducted to analyze the effects of the design parameters on the field torque. After that, simulations were done to find the optimal design under all major geometric constraints with a given power supply. The results show that the multi-pole MR brake provides a considerable braking torque increase while maintaining a compact and solid design. This is confirmation of its feasibility in actual braking applications. (paper)

Regenerative Braking System for Series Hybrid Electric City Bus

OpenAIRE

Zhang, Junzhi; Lu, Xin; Xue, Junliang; Li, Bos

2008-01-01

Regenerative Braking Systems (RBS) provide an efficient method to assist hybrid electric buses achieve better fuel economy while lowering exhaust emissions. This paper describes the design and testing of three regenerative braking systems, one of which is a series regenerative braking system and two of which are parallel regenerative braking systems. The existing friction based Adjustable Braking System (ABS) on the bus is integrated with each of the new braking systems in order to ensure bus...

Diesel Technology: Brakes. Teacher Edition [and] Student Edition.

Science.gov (United States)

Hilley, Robert; Scarberry, Terry; Kellum, Mary

This document contains teacher and student materials for a course on brakes in the diesel technology curriculum. The course consists of 12 units organized in three sections. The three units of the introductory section cover: (1) brakes; (2) wheel bearings and seals; and (3) antilock brake systems. The second section, Hydraulic Brakes, contains the…

A proposed regulatory framework for road and rail freight transport in South Africa

Directory of Open Access Journals (Sweden)

Wessel Pienaar

2007-09-01

Full Text Available The increase in the number of freight vehicles on South Africa’s rural road network has received substantial attention. Insinuations persist that long-distance road freight haulage is of a somewhat unsavoury economic nature, and that strict economic re-regulation of the land freight transport is necessary. During the 1970s road transport replaced rail carriage as the dominant form of long-distance freight transport (excluding minerals and ore in South Africa. On long hauls road freight carriers transport certain primary products of an organic nature (such as timber, fish and agricultural produce, some semi-finished goods, many finished goods and most consumer goods. Road freight carriers are continuously gaining market share on long-distance links where rail transport is the more cost efficient mode. The greater value added by road freight carriers in comparison with rail transport through service effectiveness is often more than the cost premium paid for utilising their service rather than making use of rail transport. Throughout history, governments have involved themselves in transport. A diverse range of arguments have been advanced for this involvement in transport, including the following:Control of excessive competition, co-ordination of transport, integration of transport with economic policy, maintenance of safety, security, and order, provision of costly infrastructure, provision of public goods, recovery of the true resource cost of transport inputs, regulation of harmful conduct and externalities, restraint of monopoly power, and social support. A set of nine instruments can be identified that governments apply to influence the performance of the freight transport industry: Legislation, direct supply, fiscal measures, monetary measures, moral appeal and persuasion, policies relating to strategic commodities, procurement policy, provision of information, and research and development. The best prospects for a sound development of

Emergency Brake for Tracked Vehicles

Science.gov (United States)

Green, G. L.; Hooper, S. L.

1986-01-01

Caliper brake automatically stops tracked vehicle as vehicle nears end of travel. Bar on vehicle, traveling to right, dislodges block between brake pads. Pads then press against bar, slowing vehicle by friction. Emergencybraking system suitable for elevators, amusement rides and machine tools.

Boundary effects on car accidents in a cellular automaton model

International Nuclear Information System (INIS)

Yang Xianqing; Ma Yuqiang; Zhao Yuemin

2004-01-01

In this paper we numerically study the probability P ac of occurrence of car accidents in the Nagel-Schreckenberg (NS) model with open boundary condition. In the deterministic NS model, numerical results show that there exists a critical value of extinction rate β above which no car accidents occur, and below which the probability P ac is independent of the speed limit v max and the injection rate α, but only determined by the extinction rate β. In the non-deterministic NS model, the probability P ac is a non-monotonic function of β in the region of low β value, while it is independent of β in the region of high β value. The stochastic braking not only reduces the occurrence of car accidents, but splits degenerate effects of v max on the probability P ac . Theoretical analyses give an agreement with numerical results in the deterministic NS model and in the non-deterministic NS model with v max = 1 in the case of low β value region. Qualitative differences between open and periodic systems in the relations of P ac to the bulk density ρ imply that various correlations may exist between the two systems

14 CFR 23.493 - Braked roll conditions.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Braked roll conditions. 23.493 Section 23.493 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT....493 Braked roll conditions. Under braked roll conditions, with the shock absorbers and tires in their...

Sustainable freight infrastructure to meet climate and air quality goals.

Science.gov (United States)

2012-02-01

This report examines the potential for freight modal shift from truck-to-rail in the upper Midwestern U.S. : to improve air quality and reduce CO2 emissions. Two scenarios were generated, one focusing on : intra-regional freight movements within the ...

Feasibility study for the introduction of synchromodal freight transportation concept

NARCIS (Netherlands)

Agbo, Aaron Agbenyegah; Li, Wenfeng; Atombo, Charles; Lodewijks, G.; Zheng, Lanbo

2017-01-01

The current weaknesses of the conventional intermodal freight transportation system have led to the development of the synchromodal freight transportation concept introduced and piloted in the Netherlands. The innovative concept has the advantage of adding flexibility, cost reduction, and

An extended car-following model considering the acceleration derivative in some typical traffic environments

Science.gov (United States)

Zhou, Tong; Chen, Dong; Liu, Weining

2018-03-01

Based on the full velocity difference and acceleration car-following model, an extended car-following model is proposed by considering the vehicle’s acceleration derivative. The stability condition is given by applying the control theory. Considering some typical traffic environments, the results of theoretical analysis and numerical simulation show the extended model has a more actual acceleration of string vehicles than that of the previous models in starting process, stopping process and sudden brake. Meanwhile, the traffic jams more easily occur when the coefficient of vehicle’s acceleration derivative increases, which is presented by space-time evolution. The results confirm that the vehicle’s acceleration derivative plays an important role in the traffic jamming transition and the evolution of traffic congestion.

14 CFR 27.493 - Braked roll conditions.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Braked roll conditions. 27.493 Section 27... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 27.493 Braked roll conditions. Under braked roll conditions with the shock absorbers in their static positions— (a) The limit...

14 CFR 29.493 - Braked roll conditions.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Braked roll conditions. 29.493 Section 29... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Strength Requirements Ground Loads § 29.493 Braked roll conditions. Under braked roll conditions with the shock absorbers in their static positions— (a) The limit...

49 CFR 229.57 - Foundation brake gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Foundation brake gear. 229.57 Section 229.57 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Foundation brake gear. A lever, rod, brake beam, hanger, or pin may not be worn through more than 30 percent...

FORMATION OF STRATEGY OF ECONOMIC DEVELOPMENT OF THE ENTERPRISE OF CARGO CAR BUILDING

Directory of Open Access Journals (Sweden)

N.B. Barulina

2007-12-01

Full Text Available Revival of the Russian economy and the forecast of demand for rail transportation shows, that it is necessary to update park of freight cars which has undergone significant ageing for the lack of regular updating. In the given aspect the special role is got with strategic planning activity of the large car-building enterprise of the Ural federal district – Federal state unitary enterprise "Production association "Ural Carriage-Building Plant". Authors offer strategy of economic development of the given enterprise which contains the following directions: commodity and price strategy, bases of a marketing policy, increase of personnel potential of the enterprise, development of investment process, a Directions of research and developmental activity. The predicted estimation of results of development and introduction of offered strategy of economic development of the enterprise in 2007 − 2010 is made. Spillovers and the results expected from introduction of strategy at a microlevel and a macrolevel, in social and economic sphere and budgetary sphere are submitted.

Fatigue test of a fiberglass based composite panel. Increasing the lifetime of freight wagon

Science.gov (United States)

Sobek, M.; Baier, A.; Grabowski, Ł.; Majzner, M.

2016-08-01

In the XXI century transportation of goods plays a key role in the economy. Due to a good logistics the economy is able to grow fluently. Although land transportation is carried out mainly through trucks for the last several years there has been noted an increase in the percentage share of rail transport in the freight transport. The main goods transported by railways are mineral fuels, mining and quarrying products. They constitute the greater part of 70% of total transported goods. Transportation of material of such high weight, high hardness and with different shapes involves increased and accelerated wear and tear of the cargo space of the wagon. This process is also magnified by substances used to prevent overheating or goods theft. Usually they are in the form of chemical compounds powder, eg. Calcium. A very large impact on the wear of the freight wagons hull is made because of mechanical damage. Their source comes mostly from loading cargo with impetus and using heavy machines during unloading. A large number of cycles of loading and unloading during the working period causes abrasion of body and as a result after several years a wagon car qualifies for a major maintenance. Possibility of application composite panels in the process of renovating the wagons body could reduce the weight of whole train and prolong the service life between mandatory technical inspection. The Paper "Fatigue test of a fiberglass based composite panel. Increasing the lifetime of freight wagon" presents the research process and the results of the endurance test of the composite panel samples fixed to a metal plate. As a fixing method a stainless steel rivet nut and a stainless steel button head socket screws were chosen. Cyclic and multiple load were applied to test samples using a pneumatic cylinder. Such a methodology simulated the forces resulting from loading and unloading of the wagon and movement of the cargo during transport. In the study a dedicated stand equipped with a

Optimization of an Autonomous Car Controller Using a Self-Adaptive Evolutionary Strategy

Directory of Open Access Journals (Sweden)

Tae Seong Kim

2012-09-01

Full Text Available Autonomous cars control the steering wheel, acceleration and the brake pedal, the gears and the clutch using sensory information from multiple sources. Like a human driver, it understands the current situation on the roads from the live streaming of sensory values. The decision-making module often suffers from the limited range of sensors and complexity due to the large number of sensors and actuators. Because it is tedious and difficult to design the controller manually from trial-and-error, it is desirable to use intelligent optimization algorithms. In this work, we propose optimizing the parameters of an autonomous car controller using self-adaptive evolutionary strategies (SAESs which co-evolve solutions and mutation steps for each parameter. We also describe how the most generalized parameter set can be retrieved from the process of optimization. Open-source car racing simulation software (TORCS is used to test the goodness of the proposed methods on 6 different tracks. Experimental results show that the SAES is competitive with the manual design of authors and a simple ES.

Why is energy use rising in the freight sector?

International Nuclear Information System (INIS)

Mintz, M.; Vyas, A.D.

1991-01-01

Trends in transportation sector energy use and carbon dioxide emissions are analyzed with an emphasis on three freight modes -- rail, truck, and marine. A recent set of energy use projections is presented and freight mode energy characteristics are discussed. Transportation sector energy use, which nearly doubled between 1960 and 1985, is projected to grow more slowly during the period 1985 endash 2010. Most of the growth is projected to come from non-personal modes (freight and commercial air). Trends in freight mode energy intensities are discussed and a variety of factors behind these trends are analyzed. Rail and marine modes improved their energy intensities during sudden fuel price rises of the 1970s. Though there is room for further technological improvement, long power plant life cycles preclude rapid penetration of new technologies. Thus, energy intensities in these modes are more likely to improve through operational changes. Because of relatively stable fuel prices, the energy share of truck operating expenses is likely to remain low. Coupled with increasing labor costs, this portends only modest improvements in truck energy efficiency over the next two decades

The science of vehicle dynamics handling, braking, and ride of road and race cars

CERN Document Server

Guiggiani, Massimo

2014-01-01

Vehicle dynamics is often perceived as a quite intuitive subject. As a matter of fact, lots of people are able to drive a car. Nevertheless, without a rigorous mathematical formulation it is very difficult to truly understand the physical phenomena involved in the motion of a road vehicle. In this book, mathematical models of vehicles are developed, always paying attention to state the relevant assumptions and to provide explanations for each step. This approach allows for a deep, yet simple, analysis of the dynamics of vehicles, without having to resort to foggy concepts. The reader will soon achieve a clear understanding of the subject, which will be of great help both in dealing with the challenges of designing and testing new vehicles and in tackling new research topics. The book covers handling and performance of both road and race cars. A new approach, called MAP (Map of Achievable Performance), is presented and thoroughly discussed. It provides a global and intuitive picture of the handling features of...

An evaluation of short-term exposures of brake mechanics to asbestos during automotive and truck brake cleaning and machining activities.

Science.gov (United States)

Richter, Richard O; Finley, Brent L; Paustenbach, Dennis J; Williams, Pamela R D; Sheehan, Patrick J

2009-07-01

Historically, the greatest contributions to airborne asbestos concentrations during brake repair work were likely due to specific, short-duration, dust-generating activities. In this paper, the available short-term asbestos air sampling data for mechanics collected during the cleaning and machining of vehicle brakes are evaluated to determine their impact on both short-term and daily exposures. The high degree of variability and lack of transparency for most of the short-term samples limit their use in reconstructing past asbestos exposures for brake mechanics. However, the data are useful in evaluating how reducing short-term, dust-generating activities reduced long-term exposures, especially for auto brake mechanics. Using the short-term dose data for grinding brake linings from these same studies, in combination with existing time-weighted average (TWA) data collected in decades after grinding was commonplace in rebuilding brake shoes, an average 8-h TWA of approximately 0.10 f/cc was estimated for auto brake mechanics that performed arc grinding of linings during automobile brake repair (in the 1960s or earlier). In the 1970s and early 1980s, a decline in machining activities led to a decrease in the 8-h TWA to approximately 0.063 f/cc. Improved cleaning methods in the late 1980s further reduced the 8-h TWA for most brake mechanics to about 0.0021 f/cc. It is noteworthy that when compared with the original OSHA excursion level, only 15 of the more than 300 short-term concentrations for brake mechanics measured during the 1970s and 1980s possibly exceeded the standard. Considering exposure duration, none of the short-term exposures were above the current OSHA excursion level.

Electric vehicle regenerative antiskid braking and traction control system

Science.gov (United States)

Cikanek, S.R.

1995-09-12

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydraulic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control. 10 figs.

Electric vehicle regenerative antiskid braking and traction control system

Science.gov (United States)

Cikanek, Susan R.

1995-01-01

An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydrualic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control.

On friction braking demand with regenerative braking

NARCIS (Netherlands)

Walker, A.M.; Lampérth, M.U.; Wilkins, S.

2002-01-01

Developments in Hybrid Electric and pure Electric Vehicles are intended to improve the operational efficiency of road vehicles. Regenerative braking, which has long been established in rail vehicles, is integral to efficiency improvement, with up to 30% of overall traction energy demand satisfied by

IR-camera methods for automotive brake system studies

Science.gov (United States)

Dinwiddie, Ralph B.; Lee, Kwangjin

1998-03-01

Automotive brake systems are energy conversion devices that convert kinetic energy into heat energy. Several mechanisms, mostly related to noise and vibration problems, can occur during brake operation and are often related to non-uniform temperature distribution on the brake disk. These problems are of significant cost to the industry and are a quality concern to automotive companies and brake system vendors. One such problem is thermo-elastic instabilities in brake system. During the occurrence of these instabilities several localized hot spots will form around the circumferential direction of the brake disk. The temperature distribution and the time dependence of these hot spots, a critical factor in analyzing this problem and in developing a fundamental understanding of this phenomenon, were recorded. Other modes of non-uniform temperature distributions which include hot banding and extreme localized heating were also observed. All of these modes of non-uniform temperature distributions were observed on automotive brake systems using a high speed IR camera operating in snap-shot mode. The camera was synchronized with the rotation of the brake disk so that the time evolution of hot regions could be studied. This paper discusses the experimental approach in detail.

Measuring the economic contribution of the freight industry to the Maryland economy : [research summary].

Science.gov (United States)

2015-05-01

The primary objective was to measure the economic contributions of the freight : industry to the Maryland economy and to develop a freight economic output (FECO) : index that tracks the economic performance of the freight industry over time.

Backcasting sustainable freight transport systems for Europe in 2050

International Nuclear Information System (INIS)

Mattila, Tuomas; Antikainen, Riina

2011-01-01

European freight transport emissions and fuel consumption are projected to increase. This study focuses on long distance freight transport (LDFT) and explores possible sustainable futures through quantitative modeling. The evaluation was part of European foresight process between researchers, policy makers and freight companies (FREIGHTVISION). Greenhouse gas (GHG) emissions and energy demand of road, rail and inland waterways were estimated for an EU-27 in 2005. Development was extrapolated to 2050 based on technology and freight performance forecasts. Stakeholders found the forecasted GHG emissions and fossil fuel share unsustainable, so alternative futures were developed with backcasting. The developed emission model was run with random parameter combinations to screen a set of sustainable futures, with an 80% reduction of GHG emissions and fossil fuel share. Freight transport performance was not controlled in the backcasts, but several sustainable futures were found if significant changes in transport efficiency and energy mix are implemented. In spite of agreeing on the importance of reducing emissions, stakeholders had difficulties in choosing a preferred technological future. Simple models were found to be an effective tool for communicating the influence of various measures. Further research is recommended to screen preferable technological roadmaps from the broad range of available futures. - Research highlights: → Sustainable transport systems were explored with modeling and stakeholder workshops. → Backcasting identified technological options for reducing greenhouse gas emissions by 80%. → Improving road vehicle efficiency, engine efficiency and fuel mix showed the greatest potential.

49 CFR 238.319 - Running brake test.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Running brake test. 238.319 Section 238.319... Requirements for Tier I Passenger Equipment § 238.319 Running brake test. (a) As soon as conditions safely permit, a running brake test shall be performed on each passenger train after the train has received, or...

Development of more effective methods of normalization and application at braking in turn test; Senkai seido shiken no koritsuka to oyo han`i no kakucho shuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sekine, T; Nagae, H [Nihon University, Tokyo (Japan)

1997-10-01

Recant passenger cars have so higher grades of the cornering performance that the vehicle behaviors at braking in turn have become more important for the security on the obstacle avoidance ability. In this paper, the influences of amount of initial centripetal acceleration to braking motion of vehicles are discussed by experimental and theoretical analysis. Under the higher centripetal accelerations, even smaller deceleration bring the vehicle oscillating yaw velocity phenomena as same as centripetal accelerations. As to advance the effective test procedure. the authors proposed one of the methods that enable to reduce the test error by insufficient vehicle velocity. 7 refs., 6 figs., 1 tab.

Transportation Energy Futures: Freight Transportation Modal Shares: Scenarios for a Low-Carbon Future

Energy Technology Data Exchange (ETDEWEB)

Brogan, J. J. [Cambridge Systematics Inc., Cambridge, MA (United States); Aeppli, A. E. [Cambridge Systematics Inc., Cambridge, MA (United States); Brown, D. F. [Cambridge Systematics Inc., Cambridge, MA (United States); Fischer, M. J. [Cambridge Systematics Inc., Cambridge, MA (United States); Grenzeback, L. R. [Cambridge Systematics Inc., Cambridge, MA (United States); McKenzie, E. [Cambridge Systematics Inc., Cambridge, MA (United States); Vimmerstedt, L. [Cambridge Systematics Inc., Cambridge, MA (United States); Vyas, A. D. [Cambridge Systematics Inc., Cambridge, MA (United States); Witzke, E. [Cambridge Systematics Inc., Cambridge, MA (United States)

2013-03-01

Freight transportation modes—truck, rail, water, air, and pipeline—each serve a distinct share of the freight transportation market. A variety of factors influence the modes chosen by shippers, carriers, and others involved in freight supply chains. Analytical methods can be used to project future modal shares, and federal policy actions could influence future freight mode choices. This report considers how these topics have been addressed in existing literature and offers insights on federal policy decisions with the potential to prompt mode choices that reduce energy use and greenhouse gas emissions.

Transportation Energy Futures Series: Freight Transportation Demand: Energy-Efficient Scenarios for a Low-Carbon Future

Energy Technology Data Exchange (ETDEWEB)

Grenzeback, L. R.; Brown, A.; Fischer, M. J.; Hutson, N.; Lamm, C. R.; Pei, Y. L.; Vimmerstedt, L.; Vyas, A. D.; Winebrake, J. J.

2013-03-01

Freight transportation demand is projected to grow to 27.5 billion tons in 2040, and to nearly 30.2 billion tons in 2050. This report describes the current and future demand for freight transportation in terms of tons and ton-miles of commodities moved by truck, rail, water, pipeline, and air freight carriers. It outlines the economic, logistics, transportation, and policy and regulatory factors that shape freight demand, the trends and 2050 outlook for these factors, and their anticipated effect on freight demand. After describing federal policy actions that could influence future freight demand, the report then summarizes the capabilities of available analytical models for forecasting freight demand. This is one in a series of reports produced as a result of the Transportation Energy Futures project, a Department of Energy-sponsored multi-agency effort to pinpoint underexplored strategies for reducing GHGs and petroleum dependence related to transportation.

Accelerometer-controlled automatic braking system

Science.gov (United States)

Dreher, R. C.; Sleeper, R. K.; Nayadley, J. R., Sr.

1973-01-01

Braking system, which employs angular accelerometer to control wheel braking and results in low level of tire slip, has been developed and tested. Tests indicate that system is feasible for operations on surfaces of different slipperinesses. System restricts tire slip and is capable of adapting to rapidly-changing surface conditions.

30 CFR 75.1404-1 - Braking system.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Braking system. 75.1404-1 Section 75.1404-1... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips § 75.1404-1 Braking system. A locomotive equipped with a dual braking system will be deemed to satisfy the requirements of § 75.1404 for a...

Mathematical Modeling of the Braking System of Wheeled Mainline Aircraft

Directory of Open Access Journals (Sweden)

I. S. Shumilov

2016-01-01

Full Text Available The braking system of the landing gear wheels of a mainline aircraft has to meet mandatory requirements laid out in the Aviation Regulations AP-25 (Para 25.735. «Brakes and brake systems". These requirements are essential when creating the landing gear wheel brake control system (WBCS and are used as main initial data in its mathematical modeling. The WBCS is one of the most important systems to ensure the safe completion of the flight. It is a complex of devices, i.e. units (hydraulic, electrical, and mechanical, connected through piping, wiring, mechanical constraints. This complex should allow optimizing the braking process when a large number of parameters change. The most important of them are the following: runway friction coefficient (RFC, lifting force, weight and of the aircraft, etc. The main structural elements involved in braking the aircraft are: aircraft wheels with pneumatics (air tires and brake discs, WBCS, and cooling system of gear wheels when braking.To consider the aircraft deceleration on the landing run is of essence at the stage of design, development, and improvement of brakes and braking systems. Based on analysis of equation of the aircraft motion and energy balance can be determined energy loading and its basic design parameters, braking distances and braking time.As practice and analysis of energy loading show, they (brake + wheel absorb the aircraftpossessed kinetic energy at the start of braking as much as 60-70%, 70-80%, and 80-90%, respectively, under normal increased, and emergency operating conditions. The paper presents a procedure for the rapid calculation of energy loading of the brake wheel.Currently, the mainline aircrafts use mainly electrohydraulic brake systems in which there are the main, backup, and emergency-parking brake systems. All channels are equipped with automatic anti-skid systems. Their presence in the emergency (the third reserve channel significantly improves the reliability and safety of

Goods movement study in Illinois : application to freight transportation and logistics.

Science.gov (United States)

2013-03-01

This report details the results generated by a recently completed nationwide online freight establishment study. : The survey was assembled with the intention of allowing the formulation or enhancement of new or existing : freight-demand microsimulat...

Discussion on stochastic braking for a single-rail rope-driven lifter

Energy Technology Data Exchange (ETDEWEB)

1987-02-01

This paper discusses the braking and control of a A-2/73 clip type friction brake system made in FRG - a clamp type brake system made in USSR and an eccentric wheel type brake system made in Poland. Then it analyses a ZGZ auto increasing force type braking system of a single-rail rope driven lifter. The braking principle of the ZGZ system is that the braking blocks insert along the brake base and contact with the ribs of the single-rail. Then the braking would be realized as a function of increasing frictional force.

Electronic Freight Management (EFM) Governance

Science.gov (United States)

2012-03-01

The Electronic Freight Management (EFM) initiative is a USDOT-sponsored project that applies web technologies to improve data and message transmissions between supply chain partners. This report describes a new EFM Governance Model and the necessary ...

Road freight and the environment

CSIR Research Space (South Africa)

Makamo, N

2015-07-01

Full Text Available freight transport are categorised as direct or secondary impacts. Externalities are an economic concept that refers to activities that have unintended consequences, positive or negative consequences. This review considers the different environmental links...

Clutches and brakes design and selection

CERN Document Server

Orthwein, William C

2004-01-01

Conveniently gathering formulas, analytical methods, and graphs for the design and selection of a wide variety of brakes and clutches in the automotive, aircraft, farming, and manufacturing industries, Clutches and Brakes: Design and Selection, Second Edition simplifies calculations, acquaints engineers with an expansive range of application, and assists in the selection of parameters for specific design challenges. Contains an abundance of examples, 550 display equations, and more than 200 figures for clear presentation of various design strategies Thoroughly revised throughout, the second edition offers… Additional chapters on friction drives and fluid clutches and retarders An extended discussion on cone brakes and clutches A simpler formulation of the torque from a centrifugal clutch Updated sections on automatic braking systems An analysis of variable-speed friction drives with clutch capability Analytical and computer-assisted design techniques.

Evaluation of materials and design modifications for aircraft brakes

Science.gov (United States)

Ho, T. L.; Kennedy, F. E.; Peterson, M. B.

1975-01-01

A test program is described which was carried out to evaluate several proposed design modifications and several high-temperature friction materials for use in aircraft disk brakes. The evaluation program was carried out on a specially built test apparatus utilizing a disk brake and wheel half from a small het aircraft. The apparatus enabled control of brake pressure, velocity, and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The results of the design evaluation program showed that some improvement in brake performance can be realized by making design changes in the components of the brake containing friction material. The materials evaluation showed that two friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary since both materials show a significant negative slope of the friction-velocity curve at low velocities.

Urban distribution centers : a means to reducing freight vehicle miles traveled.

Science.gov (United States)

2011-02-01

The present study examines the model of freight consolidation platforms, and urban distribution centers (UDCs) in particular, as a means to solve the last mile problem of urban freight while reducing vehicle miles traveled and associated environmenta...

Flex Cargo Rail. Developing new service, collection and distribution concepts for the transport of freight by rail.; Flex Cargo Rail. Wege zu neuen Bedien-, Sammel- und Verteilkonzepten im Schienengueterverkehr

Energy Technology Data Exchange (ETDEWEB)

Kochsiek, Joachim [Fraunhofer-Institut fuer Materialfluss und Logistik (IML), Dortmund (Germany). Gruppe Multimodale Logistik

2010-07-01

FlexCargoRail is a concept for self propelled electric freight wagons. This will enhance rail operations on first and last mile. The concept can be integrated in the existing rail system, so migration is possible without any lost investments. Standard components from industry and rail are used to realise the FCR wagon. Motors, transmissions, control and batteries are available and approved. One of the effects is to enhance service for loading terminals. This can become independent from factory siding operation. From the economic point of view, FCR is realisable. This is shown by target costing. Efficiency of FCR is dependent from high frequent use of FCR rail cars and the use of the possibility to shunt also conventional freight wagons with FCR wagons. Migration should be carried out in logistical networks with frequent operations between plants and sidings with a closed wagon pool. (orig.)

49 CFR 238.231 - Brake system.

Science.gov (United States)

2010-10-01

...) Equipped with brake indicators as defined in § 238.5, designed so that the pressure sensor is placed in a... alcohol or other chemicals into the air brake system of passenger equipment is prohibited. (f) The...

Combined braking system for hybrid vehicle

Science.gov (United States)

Kulekina, A. V.; Bakholdin, P. A.; Shchurov, N. I.

2017-10-01

The paper presents an analysis of surface vehicle’s existing braking systems. The technical solution and brake-system design were developed for use of regenerative braking energy. A technical parameters comparison of energy storage devices of various types was made. Based on the comparative analysis, it was decided to use supercapacitor because of its applicability for an electric drive intermittent operation. The calculation methods of retarder key components were proposed. Therefrom, it was made a conclusion that rebuild gasoline-electric vehicles are more efficient than gasoline ones.

Price Analysis of Railway Freight Transport under Marketing Mechanism

Science.gov (United States)

Shi, Ying; Fang, Xiaoping; Chen, Zhiya

Regarding the problems in the reform of the railway tariff system and the pricing of the transport, by means of assaying the influence of the price elasticity on the artifice used for price, this article proposed multiple regressive model which analyzed price elasticity quantitatively. This model conclude multi-factors which influences on the price elasticity, such as the averagely railway freight charge, the averagely freight haulage of proximate supersede transportation mode, the GDP per capita in the point of origin, and a series of dummy variable which can reflect the features of some productive and consume demesne. It can calculate the price elasticity of different classes in different domains, and predict the freight traffic volume on different rate levels. It can calculate confidence-level, and evaluate the relevance of each parameter to get rid of irrelevant or little relevant variables. It supplied a good theoretical basis for directing the pricing of transport enterprises in market economic conditions, which is suitable for railway freight, passenger traffic and other transportation manner as well. SPSS (Statistical Package for the Social Science) software was used to calculate and analysis the example. This article realized the calculation by HYFX system(Ministry of Railways fund).

77 FR 51649 - Federal Motor Vehicle Safety Standards; Motorcycle Brake Systems

Science.gov (United States)

2012-08-24

... motorcycle braking regulations from around the world, including the U.S. motorcycle brake systems standard.... Partial Failure Test--Split Service Brake System I. Power-Assisted Braking System Failure Test V. Other... motorcycle brake system technologies. In order to address modern braking technologies, the agency sought to...

Improving freight crash incident management.

Science.gov (United States)

2015-06-01

The objective of this study was to determine the most effective way to mitigate the effect of freight : crash incidents on Louisiana freeways. Candidate incident management strategies were reviewed from : practice in other states and from those publi...

Hierarchical Control Strategy for the Cooperative Braking System of Electric Vehicle

Science.gov (United States)

Peng, Jiankun; He, Hongwen; Guo, Hongqiang

2015-01-01

This paper provides a hierarchical control strategy for cooperative braking system of an electric vehicle with separated driven axles. Two layers are defined: the top layer is used to optimize the braking stability based on two sliding mode control strategies, namely, the interaxle control mode and signal-axle control strategies; the interaxle control strategy generates the ideal braking force distribution in general braking condition, and the single-axle control strategy can ensure braking safety in emergency braking condition; the bottom layer is used to maximize the regenerative braking energy recovery efficiency with a reallocated braking torque strategy; the reallocated braking torque strategy can recovery braking energy as much as possible in the premise of meeting battery charging power. The simulation results show that the proposed hierarchical control strategy is reasonable and can adapt to different typical road surfaces and load cases; the vehicle braking stability and safety can be guaranteed; furthermore, the regenerative braking energy recovery efficiency can be improved. PMID:26236772

Hierarchical Control Strategy for the Cooperative Braking System of Electric Vehicle.

Science.gov (United States)

Peng, Jiankun; He, Hongwen; Liu, Wei; Guo, Hongqiang

2015-01-01

This paper provides a hierarchical control strategy for cooperative braking system of an electric vehicle with separated driven axles. Two layers are defined: the top layer is used to optimize the braking stability based on two sliding mode control strategies, namely, the interaxle control mode and signal-axle control strategies; the interaxle control strategy generates the ideal braking force distribution in general braking condition, and the single-axle control strategy can ensure braking safety in emergency braking condition; the bottom layer is used to maximize the regenerative braking energy recovery efficiency with a reallocated braking torque strategy; the reallocated braking torque strategy can recovery braking energy as much as possible in the premise of meeting battery charging power. The simulation results show that the proposed hierarchical control strategy is reasonable and can adapt to different typical road surfaces and load cases; the vehicle braking stability and safety can be guaranteed; furthermore, the regenerative braking energy recovery efficiency can be improved.