Magnetisation and AC susceptibility studies of La1-xSrxFe0.8Cr0.2O3-δ (0.01.0) perovskites

International Nuclear Information System (INIS)

Ferreira, L.P.; Cruz, M.M.; Ramos, T.; Sa, M.A.; Carvalho, M.D.; Godinho, M.

2007-01-01

Magnetisation and AC magnetic susceptibility measurements have been performed in the perovskite-type compounds La 1-x Sr x Fe 0.8 Cr 0.2 O 3-δ (x=0.2, 0.4, 0.6 and 0.8). All compounds show an overall antiferromagnetic behaviour mainly attributed to predominant Fe 3+ -O-Fe 3+ interactions. For 0.2 ord . The coexistence of AFM and FM interactions leads to reentrant magnetic behaviour for the x=0.4 compound and to spin-glass like behaviour for x=0.8. Between x=0.6 and 0.8, the similar magnetic moments found in the paramagnetic region indicate that the Fe/Cr valences do not change significantly, pointing towards an increased role for oxygen vacancy formation in the charge compensation mechanism

Permanent magnets prepared from Sm{sub 10.5}Fe{sub 88.5}Zr{sub 1.0}N{sub y} without homogenization

Energy Technology Data Exchange (ETDEWEB)

Gebel, B.; Kubis, M.; Mueller, K.-H. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe

1997-10-01

In as-cast Sm{sub 2}Fe{sub 17} the high amount of {alpha}-Fe caused by a peritectic reaction can be considerably reduced by a small addition of about 1 at% Zr. X-ray diffraction showed that as-cast Sm{sub 10.5}Fe{sub 88.5}Zr{sub 1.0} mainly consists of a phase with the Th{sub 2}Zn{sub 17}-type structure and SmFe{sub 3}. Non-homogenized Sm{sub 10.5}Fe{sub 88.5}Zr{sub 1.0} was milled and (i) annealed in vacuum or (ii) treated with a hydrogenation-disproportionation-desorp tion-recombination (HDDR) process. The annealed and subsequently nitrogenated powder is magnetically anisotropic and has a coercivity {mu}{sub 0J}H{sub C} up to 2.0 T and an energy product (BH){sub max} up to 136 kJ/m{sup 3}. HDDR-treated and nitrogenated powder is isotropic and exhibits values of {mu}{sub 0J}H{sub C} = 3.1 T and (BH){sub max} 103 kJ/m{sup 3}. Consequently, Sm{sub 10.5}Fe{sub 88.5}Zr{sub 1.0}N{sub y} (y {approx} 16) permanent magnets with very good properties can be prepared without the time-consuming homogenization procedure. (orig.). 11 refs.

(La, Pr)0.8Sr0.2FeO3-δ-Sm 0.2Ce0.8O2-δ composite cathode for proton-conducting solid oxide fuel cells

KAUST Repository

Chen, Yonghong

2014-08-01

Mixed rare-earth (La, Pr)0.8Sr0.2FeO 3-δ-Sm0.2Ce0.8O2-δ (LPSF-SDC) composite cathode was investigated for proton-conducting solid oxide fuel cells based on protonic BaZr0.1Ce0.7Y 0.2O3-δ (BZCY) electrolyte. The powders of La 0.8-xPrxSr0.2FeO3-δ (x = 0, 0.2, 0.4, 0.6), Sm0.2Ce0.8O2-δ (SDC) and BaZr0.1Ce0.7Y0.2O3-δ (BZCY) were synthesized by a citric acid-nitrates self-propagating combustion method. The XRD results indicate that La0.8-xPrxSr 0.2FeO3-δ samples calcined at 950 °C exhibit perovskite structure and there are no interactions between LPSF0.2 and SDC at 1100 °C. The average thermal expansion coefficient (TEC) of LPSF0.2-SDC, BZCY and NiO-BZCY is 12.50 × 10-6 K-1, 13.51 × 10-6 K-1 and 13.47 × 10-6 K -1, respectively, which can provide good thermal compatibility between electrodes and electrolyte. An anode-supported single cell of NiO-BZCY|BZCY|LPSF0.2-SDC was successfully fabricated and operated from 700 °C to 550 °C with humidified hydrogen (∼3% H2O) as fuel and the static air as oxidant. A high maximum power density of 488 mW cm -2, an open-circuit potential of 0.95 V, and a low electrode polarization resistance of 0.071 Ω cm2 were achieved at 700 °C. Preliminary results demonstrate that LPSF0.2-SDC composite is a promising cathode material for proton-conducting solid oxide fuel cells. © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Study of the reaction of astrophysical interest 60Fe(n,γ)61Fe via (d,pγ) transfer reaction

International Nuclear Information System (INIS)

Giron, S.

2011-12-01

60 Fe is of special interest in nuclear astrophysics. Indeed the recent observations of 60 Fe characteristic gamma-ray lines by the RHESSI and INTEGRAL spacecrafts allowed to measure the total flux of 60 Fe over the Galaxy. Moreover the observation in presolar grains of an excess of the daughter-nuclei of 60 Fe, 60 Ni, gives constraints on the conditions of formation of the early solar system. However, the cross-sections of some reactions involved in 60 Fe nucleosynthesis and included to stellar models are still uncertain. The destruction reaction of 60 Fe, 60 Fe(n, γ) 61 Fe, is one of them. The total cross-section can be separate into two contributions: the direct one, involving states below the neutron separation threshold of 61 Fe, and the resonant one.We improved 61 Fe spectroscopy in order to evaluate the direct capture part of the 60 Fe(n, γ) 61 Fe reaction cross-section. 60 Fe(n, γ) 61 Fe was thus studied via d( 60 Fe, pγ) 61 Fe transfer reaction with the CATS/MUST2/EXOGAM setup at LISE-GANIL. DWBA analysis of experimental proton differential cross-sections allowed to extract orbital angular momentum and spectroscopic factors of different populated states identified below the neutron threshold. A comparison of experimental results for 61 Fe with experimental results for similar nuclei and with shell-model calculations was also performed. (author) [fr

A method for determination of [Fe3+]/[Fe2+] ratio in superparamagnetic iron oxide

Science.gov (United States)

Jiang, Changzhao; Yang, Siyu; Gan, Neng; Pan, Hongchun; Liu, Hong

2017-10-01

Superparamagnetic iron oxide nanoparticles (SPION), as a kind of nanophase materials, are widely used in biomedical application, such as magnetic resonance imaging (MRI), drug delivery, and magnetic field assisted therapy. The magnetic property of SPION has close connection with its crystal structure, namely it is related to the ratio of Fe3+ and Fe2+ which form the SPION. So a simple way to determine the content of the Fe3+ and Fe2+ is important for researching the property of SPION. This review covers a method for determination of the Fe3+ and Fe2+ ratio in SPION by UV-vis spectrophotometry based the reaction of Fe2+ and 1,10-phenanthroline. The standard curve of Fe with R2 = 0.9999 is used for determination the content of Fe2+ and total iron with 2.5 mL 0.01% (w/v) SPION digested by HCl, pH = 4.30 HOAc-NaAc buffer 10 mL, 0.01% (w/v) 1,10-phenanthroline 5 mL and 10% (w/v) ascorbic acid 1 mL for total iron determine independently. But the presence of Fe3+ interfere with obtaining the actual value of Fe2+ (the error close to 9%). We designed a calibration curve to eliminate the error by devising a series of solution of different ratio of [Fe3+]/[Fe2+], and obtain the calibration curve. Through the calibration curve, the error between the measured value and the actual value can be reduced to 0.4%. The R2 of linearity of the method is 0.99441 and 0.99929 for Fe2+ and total iron respectively. The error of accuracy of recovery and precision of inter-day and intra-day are both lower than 2%, which can prove the reliability of the determination method.

78 FR 59949 - Annual Factors for Determining Public Housing Agency Administrative Fees for the Section 8...

Science.gov (United States)

2013-09-30

... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5724-N-02] Annual Factors for... Web site of the annual factors for determining the on-going administrative fee for housing agencies... Relay Service during business hours at 1-800-877-8337. SUPPLEMENTARY INFORMATION: The annual factors for...

77 FR 62150 - Approval and Promulgation of Implementation Plans; Kentucky; Approval of Revisions to the...

Science.gov (United States)

2012-10-12

....34 Standard of 10/23/01 66 FR 53661 05/15/91 Performance for Existing Pneumatic Rubber Tire... Abbreviations and 11/19/02 67 FR 69688 05/15/02 Acronyms. 1.04 Performance Tests... 10/23/01 66 FR 53660 11/19... 10/23/01 66 FR 53660 06/13/79 Requirements. Reg 6--Standards of Performance for Existing Affected...

X-ray diffraction and Moessbauer study of (Fe1-xNi x)4N (0.2 ≤ x ≤ 0.6) films

International Nuclear Information System (INIS)

El Khiraoui, S.; Sajieddine, M.; Vergnat, M.; Sahlaoui, M.; Bauer, Ph.; Mabrouki, M.

2007-01-01

Single phase (Fe 1-x Ni x ) 4 N compounds (0.2 ≤ x ≤ 0.6) have been synthesized by reactive evaporation and investigated by X-ray diffraction and Moessbauer spectrometry. The lattice parameters of the nitrides decrease from 3.796 to 3.774 A with increasing Ni concentration. The fitting results of Moessbauer spectra indicate that the average hyperfine field have the same changing tendency with lattice parameter and the nickel atoms have a tendency to be located at the corner site

Synthesis of porous LiFe0.2Mn1.8O4 with high performance for lithium-ion battery

International Nuclear Information System (INIS)

Shi, Yishan; Zhu, Shenmin; Zhu, Chengling; Li, Yao; Chen, Zhixin; Zhang, Di

2015-01-01

Highlights: • Porous LiFe 0.2 Mn 1.8 O 4 was fabricated with P123 as a template through a nitrate decomposition method • A high rate capacity and cycling stability were demonstrated when used as cathode in LIBs • This strategy is expected to fabricate other multiple metal oxides with porous structures - Abstract: A facile and effective route was developed for the fabrication of LiFe 0.2 Mn 1.8 O 4 with porous structures by using Pluronic P-123 as a soft template, based on a nitrate decomposition method. The resultant LiFe 0.2 Mn 1.8 O 4 was characterized by XRD, SEM, as well as N 2 adsorption/desorption measurements which showed a porous structure with a pore size centered at 20 nm. When used as cathode materials in lithium battery, the as-synthesized LiFe 0.2 Mn 1.8 O 4 exhibited a discharge capacity of 122 mAh g −1 at 1 C and 102 mAh g −1 at 5 C. Moreover, after 500 cycles, the capacity retention (108 mAh g −1 ) reached 88% of the initial capacity at 1 C. As compared with conventional cathode LiMn 2 O 4 , the high performance is believed to originate from the combined effects of porous structure, iron doping and highly crystalline nature of the obtained LiFe 0.2 Mn 1.8 O 4 . This strategy is expected to allow the fabrication of other multiple metal oxides with porous structures for high performance cathode materials

Atomistic modeling determination of placeholder binding energy of Ti, C, and N atoms on a-Fe (100) surfaces

International Nuclear Information System (INIS)

Wei, X J; Liu, Y P; Han, S P

2015-01-01

A Fe(100) surface containing Ti, C, and N was constructed and optimized to study the placeholder binding energy of the Ti, C, and N surface atoms; this was achieved by searching the transition state with the LST (linear synchronous transit) method of the CASTEP (Cambridge Serial Total Energy Package) module. Also, the authors analyzed electron structures to determine how Ti, C, and N atoms strengthen the Fe(100) surface. The results show that when Ti, C, or N atoms take placeholder alone, or simultaneously at the Fe(100) surface, the structure stability is at its best. When including Ti, C, and N as solid solutions on the Fe(100) surface, orbital electrons of Fe3d, Ti3d, C2p, and N2p hybridize near the Fermi level; the number of electronic bonding peaks increase and bonding capacity enhances. Also, a large amount of covalent bonds formed. Covalent bonds and metallic bond coexisted. (paper)

57Fe Moessbauer and magnetization study of the Th7Fe3 and the hydride Th7Fe3H/sub n/

International Nuclear Information System (INIS)

Viccaro, P.J.; Shenoy, G.K.; Dunlap, B.D.; Westlake, D.G.; Malik, S.K.; Wallace, W.E.

1978-01-01

Th 7 Fe 3 is known to be a Pauli paramagnet and to undergo a superconducting transition at 1.86K. Its hydride Th 7 Fe 3 H/sub n/ is shown to possess magnetic ordering. The 57 Fe saturated hyperfine field in the hydride is estimated to be aproximately 20kG. A positive isomer shift of 0.30 +- 0.02 mm/s at 300 K relative to Th 7 Fe 3 would be consistent with an increase in d-like electrons on Fe. Preliminary magnetization results indicate a magnetic moment of about 0.5 μ/sub B/ for the hydride and a transition temperature near 300 K

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3-d measured by in-situ neutron diffraction

NARCIS (Netherlands)

McIntosh, Steven; McIntosh, S.; Vente, Jaap F.; Haije, Wim G.; Blank, David H.A.; Bouwmeester, Henricus J.M.

2006-01-01

The phase stability, oxygen stoichiometry and expansion properties of SrCo0.8Fe0.2O3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5×10−4 to 1 atm. At a pO2 of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across

Resistencia a la corrosión atmosférica del recubrimiento Zn-10,2% Fe sobre chapa de acero. Comparación con el recubrimiento de zinc

Directory of Open Access Journals (Sweden)

Arnau, G.

1998-05-01

Full Text Available Zn-10.2 % Fe galvanized coating versus hot galvanized coating over carbon steel corrosion performance has been studied. Different periods of atmospheric exposures in various Valencia Community sites, and salt spray accelerated test have been done. Carbon steel test samples have been used simultaneously in order to classify exposure atmosphere corrosivity, and environmental exposure atmosphere characteristics have been analyzed. Corrosion velocity versus environmental parameters has been obtained.

Se estudia el comportamiento a la corrosión atmosférica de un recubrimiento Zn-10,2 % Fe galvanizado en caliente, comparándolo con el comportamiento ofrecido por la chapa galvanizada, habiéndose aplicado ambos recubrimientos sobre chapa de acero de embutición. Se han realizado ensayos de exposición atmosférica en distintas atmósferas de la Comunidad Valenciana y ensayos acelerados de laboratorio en cámara de niebla salina. Se han empleado simultáneamente probetas testigo de acero con el fin de clasificar la corrosividad de las atmósferas, y se han estudiado las características medioambientales de las atmósferas donde se han llevado a cabo los ensayos. Mediante estos estudios se han obtenido las velocidades de corrosión y se han analizado en función de los parámetros ambientales.

Spectro-photometric determinations of Mn, Fe and Cu in aluminum master alloys

Science.gov (United States)

Rehan; Naveed, A.; Shan, A.; Afzal, M.; Saleem, J.; Noshad, M. A.

2016-08-01

Highly reliable, fast and cost effective Spectro-photometric methods have been developed for the determination of Mn, Fe & Cu in aluminum master alloys, based on the development of calibration curves being prepared via laboratory standards. The calibration curves are designed so as to induce maximum sensitivity and minimum instrumental error (Mn 1mg/100ml-2mg/100ml, Fe 0.01mg/100ml-0.2mg/100ml and Cu 2mg/100ml-10mg/ 100ml). The developed Spectro-photometric methods produce accurate results while analyzing Mn, Fe and Cu in certified reference materials. Particularly, these methods are suitable for all types of Al-Mn, Al-Fe and Al-Cu master alloys (5%, 10%, 50% etc. master alloys).Moreover, the sampling practices suggested herein include a reasonable amount of analytical sample, which truly represent the whole lot of a particular master alloy. Successive dilution technique was utilized to meet the calibration curve range. Furthermore, the workout methods were also found suitable for the analysis of said elements in ordinary aluminum alloys. However, it was observed that Cush owed a considerable interference with Fe, the later one may not be accurately measured in the presence of Cu greater than 0.01 %.

Speciative Determination of Dissolved Inorganic Fe(II), Fe(III) and Total Fe in Natural Waters by Coupling CPE with FAAS

International Nuclear Information System (INIS)

Gurkan, R.; Altunay, N.

2013-01-01

A new cloud point extraction (CPE) method for the preconcentration of trace iron speciation in natural waters prior to determination by flame atomic absorption spectrometry (FAAS) was developed in the present study. In this method, Fe(II) sensitively and selectively reacts with Calcon carboxylic acid (CCA) in presence of cetylpyridinium chloride (CPC) yielding a hydrophobic complex at pH 10.5, which is then entrapped in surfactant-rich phase. Total Fe was accurately and reliably determined after the reduction of Fe(III) to Fe(II) with sulfite. The amount of Fe(III) in samples was determined from the difference between total Fe and Fe(II). CPC was used not only as an auxiliary ligand in CPE, but also as sensitivity enhancement agent in FAAS. The nonionic surfactant, polyethylene glycol tert-octylphenyl ether (Triton X-114) was used as an extracting agent. The analytical variables affecting CPE efficiency were investigated in detail. The preconcentration/enhancement factors of 50 and 82 respectively, were obtained for the preconcentration of Fe(II) with 50 mL solution. Under the optimized conditions, the detection limit of Fe(II) in linear range of 0.2-60 μg L/sup -1/ was 0.06 μg L/sup -1/. The relative standard deviation was 2.7 percentage (20 μg L/sup -1/, N: 5), recoveries for Fe(II) were in range of 99.0-102.0 percentage for all water samples including certified reference materials (CRMs). In order to verify its accuracy, two CRMs were analyzed and the results obtained were statistically in good agreement with the certified values. (author)

MD simulation of atomic displacement cascades in Fe-10 at.%Cr binary alloy

International Nuclear Information System (INIS)

Tikhonchev, M.; Svetukhin, V.; Kadochkin, A.; Gaganidze, E.

2009-01-01

Molecular dynamics simulation of atomic displacement cascades up to 20 keV has been performed in Fe-10 at.%Cr binary alloy at a temperature of 600 K. The N-body interatomic potentials of Finnis-Sinclair type were used. According to the obtained results the dependence of 'surviving' defects amount is well approximated by power function that coincides with other researchers' results. Obtained cascade efficiency for damage energy in the range from 10 to 20 keV is ∼0.2 NRT that is slightly higher than for pure α-Fe. In post-cascade area Cr fraction in interstitials is in range 2-5% that is essentially lower than Cr content in the base alloy. The results on size and amount of vacancy and interstitial clusters generated in displacement cascades are obtained. For energies of 2 keV and higher the defect cluster average size increases and it is well approximated by a linear dependence on cascade energy both for interstitials and vacancies.

MD simulation of atomic displacement cascades in Fe-10 at.%Cr binary alloy

Energy Technology Data Exchange (ETDEWEB)

Tikhonchev, M., E-mail: tikhonchev@sv.ulsu.r [Ulyanovsk State University, Leo Tolstoy Str., 42, Ulyanovsk 432970 (Russian Federation); Joint Stock Company, ' State Scientific Center Research Institute of Atomic Reactors' , 433510 Dimitrovgrad-10 (Russian Federation); Svetukhin, V.; Kadochkin, A. [Ulyanovsk State University, Leo Tolstoy Str., 42, Ulyanovsk 432970 (Russian Federation); Gaganidze, E. [Forschungszentrum Karlsruhe, IMF II, 3640, D-76021 Karlsruhe (Germany)

2009-12-15

Molecular dynamics simulation of atomic displacement cascades up to 20 keV has been performed in Fe-10 at.%Cr binary alloy at a temperature of 600 K. The N-body interatomic potentials of Finnis-Sinclair type were used. According to the obtained results the dependence of 'surviving' defects amount is well approximated by power function that coincides with other researchers' results. Obtained cascade efficiency for damage energy in the range from 10 to 20 keV is approx0.2 NRT that is slightly higher than for pure alpha-Fe. In post-cascade area Cr fraction in interstitials is in range 2-5% that is essentially lower than Cr content in the base alloy. The results on size and amount of vacancy and interstitial clusters generated in displacement cascades are obtained. For energies of 2 keV and higher the defect cluster average size increases and it is well approximated by a linear dependence on cascade energy both for interstitials and vacancies.

Fe-N and (Fe, Ni)-N Fine Powders for Magnetic Recording

International Nuclear Information System (INIS)

Chen Ziyu; Li Fashen

1998-01-01

Combining Moessbauer spectroscopy with magnetic property measurement, we have studied Fe-N and (Fe, Ni)-N powders for magnetic recording. The typical particles of the core (α-Fe)/shell (γ'-Fe 4 N) structure have been successfully prepared. All the products are stabilized in a multi-organic solution. It has been found that the coercivity can be changed from 300 to 800 Oe by adjusting the shape of the particles. The special saturation magnetization of the particles can be adjusted from 120 to 180emu/g and their chemical stability is improved by substituting nickel for iron in γ'-Fe 4 N. Following experiments for corrosion resistance, it is expected that (Fe, Ni)-N and the core/shell particles will be applied as recording media in the near future

Fe-N and (Fe, Ni)-N Fine Powders for Magnetic Recording

Energy Technology Data Exchange (ETDEWEB)

Chen Ziyu; Li Fashen [Lanzhou University, Department of Physics (China)

1998-12-15

Combining Moessbauer spectroscopy with magnetic property measurement, we have studied Fe-N and (Fe, Ni)-N powders for magnetic recording. The typical particles of the core ({alpha}-Fe)/shell ({gamma}'-Fe{sub 4}N) structure have been successfully prepared. All the products are stabilized in a multi-organic solution. It has been found that the coercivity can be changed from 300 to 800 Oe by adjusting the shape of the particles. The special saturation magnetization of the particles can be adjusted from 120 to 180emu/g and their chemical stability is improved by substituting nickel for iron in {gamma}'-Fe{sub 4}N. Following experiments for corrosion resistance, it is expected that (Fe, Ni)-N and the core/shell particles will be applied as recording media in the near future.

Quemaduras por frío: Revisión de 10 Años

OpenAIRE

EULUFÍ M, ALEX; PIÑEROS B, JOSÉ LUIS; CALDERÓN O, WILFREDO; CUADRA C, ÁLVARO; DANILLA E, STEFAN; LÉNIZ M, PATRICIO; ROCO M, HÉCTOR; ROA G, RICARDO; EULUFÍ M, CHRISTIAN

2006-01-01

La injuria por frío ha sido objeto de estudio desde la década de 1960, Este trabajo entrega los resultados de una revisión retrospectiva de un grupo de 10 pacientes ingresados al Hospital del Trabajador de Santiago (HTS) en un periodo de 10 años producto de accidentes laborales de distintas etiologías. Cabe señalar que solo encontramos reportes aislados de casos en la literatura revisada. Se revisaron retrospectivamente las fichas clínicas de 10 pacientes en el periodo 1993-2003. Las edades f...

Determination of Ca, Fe, Cu and Zn content in hair by EDXRF method

International Nuclear Information System (INIS)

Yang Mingtai; Chen Jinhua; Qi Honglian; Gao Ge

1994-01-01

The authors introduce an analysing method that can determine simultaneously Ca, Fe, Cu and Zn in hair by using energy-dispersive X ray fluorescence analyzer of tube-excite type made in China. The added element Y is used as internal standard in hair sample. The hair is resolved by chemical reagent to make test sample, then the energy-dispersive X ray fluorescence analyzer is used to determine Ca, fe, Cu and Zn contents in hair sample. The lower limits of detection are 7 x 10 -6 , 1 x 10 -6 , 4 x 10 -6 , 3 x 10 -6 , respectively. Correlative coefficients of variations are 6%, 1%, 2%, 2%

NRC Bulletin No. 87-02, Supplement 1: Fastener testing to determine conformance with applicable material specifications

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

Item 5 of NRC Compliance Bulletin 87-02 requested that all holders of operating licenses or construction permits for nuclear power reactors information regarding the identity of the suppliers and manufacturers of the safety-related and non-safety-related fasteners selected for testing. After further consideration, the NRC has determined that it needs information regarding the identity of all vendors from which safety-related and non-safety-related fasteners have been obtained within the past 10 years, a reasonable period which will not put undue burden on addressees. This information will assist the NRC in determining whether nuclear facility fasteners in use have been supplied in accordance with their intended use. In addition, this information is needed so that the NRC can properly coordinate information with other government agencies concerned with problems identified in the quality of fasteners

Enhancement of plasticity of Fe-based bulk metallic glass by Ni substitution for Fe

Energy Technology Data Exchange (ETDEWEB)

Guo, S.F. [State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China); State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Li, N.; Zhang, C. [State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China); Liu, L., E-mail: sfguo2005@163.co [State Key Laboratory of Material Processing and Die and Mould Technology, Huazhong University of Science and Technology, 430074 Wuhan (China)

2010-08-15

Bulk metallic glasses (BMGs) (Fe{sub 1-x}Ni{sub x}){sub 71}Mo{sub 5}P{sub 12}C{sub 10}B{sub 2} (x = 0, 0.1 and 0.2) with a diameter of 3 mm were synthesized by copper mold casting. The effect of Ni substitution for Fe on the structure, thermal and mechanical properties has been studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and compressive testing. It was found that the substitution of Ni for Fe enhances the glass forming ability, and improves the plasticity of Fe{sub 71}Mo{sub 5}P{sub 12}C{sub 10}B{sub 2} BMG as indicated by the increase in the plastic strain from 3.1% (x = 0) to 5.2% (x = 0.2). The improvement of the plasticity is discussed in term of the reduction of glass transition temperature and the supercooled liquid region due to the substitution of Ni for Fe.

2-Hydro-4-n-But oxypropiophenone Oxime as a spectrophotometric reagent for Fe (III)

International Nuclear Information System (INIS)

Purohit, K.; Desai, K.K.

2006-01-01

2-Hydro-4-n-But oxypropiophenone Oxime [Hipbone] has been synthesized and used for the spectrophotometric determination of Fe (III). The reagent gives purple coloured complex with Fe (III) in 50% alcoholic medium in pH range of 2.5-4.5. Beer's law is obeyed up to 23.1 ppm of Fe (III). Molar absorptivity and sandell's sensitivity at 500 nm of complex were found to be 7.062x 10 power2 lit.mol.cm and 0.079 ug of Fe (III)/cm respectively. Composition and stability constant have been determined. The reagent is successfully used for determination of Fe (III) in dolomite and in pharmaceutical sample. It is also used for the indirect determination of fluoride in tap water sample. (author)

Cinética de engrosamiento de precipitados coherentes en la aleación Fe-10 % Ni-15 % Al

Directory of Open Access Journals (Sweden)

Cayetano-Castro, N.

2008-04-01

Full Text Available The coarsening kinetics and the morphology evolution of the coherent β’ (Fe, NiAl precipitates embedded in a ferritic matrix were studied in the aged Fe-10 % Ni-15 % Al alloy. Samples were solution treated at 1,100°C for 24 h and subsequently aged at 750, 850 and 920 °C for different times. XRD, SEM and TEM results showed the following decomposition reaction after aging treatment, α_sss → α + β. Intragranular particles distribution changes from a random to an aligned on the elastically soft <100> crystallographic directions of the matrix. Additionally, the morphological evolution of the precipitates was as follows: spheres → cuboids → parallelepipeds → plates. The variation of the cube of mean radius of particles, r³, and the particle density as a function of time followed a linear relationship, as predicted by the Lifshitz, Slyosov and Wagner (LSW theory for diffusion-controlled coarsening. The rate constant (K increased with the aging temperature. The activation energy for coarsening process was determined to be about of 220 kJ/mol.

La cinética de engrosamiento y la evolución morfológica de precipitados coherentes β’ (Fe, NiAl en una matriz ferrítica se estudió en la aleación Fe-10 % Ni-15 % Al. Se solubilizaron muestras a 1.100 °C por 24, y posteriormente, se envejecieron a 750, 850 y 920 °C por diferentes tiempos. Los resultados de DRX, MEB y MET mostraron la descomposición, α_sss → α + β, durante su envejecido. La distribución de precipitados dentro del grano cambia, gradualmente, de aleatoria a un alineamiento preferencial sobre las direcciones cristalográficas <100> de la matriz. Asimismo, la evolución morfológica de los precipitados fue: esféricos → cúbicos → paralelepípedos → placas. La variación del tamaño de partícula, r³, y la densidad de precipitados en función del tiempo se comportan linealmente, como lo predice la teoría de Lifshitz

Diffusion of N adatoms on the Fe(100) surface

DEFF Research Database (Denmark)

Pedersen, M. Ø.; Österlund, L.; Mortensen, Jens Jørgen

2000-01-01

The diffusion of individual N adatoms on Fe(100) has been studied using scanning tunneling microscopy and ab initio density functional theory (DFT) calculations. The measured diffusion barrier for isolated N adatoms is E-d = (0.92 +/- 0.04) eV, with a prefactor of nu(0) = 4.3 x 10(12) s(-1), which...... is in quantitative agreement with the DFT calculations. Thr; diffusion is strongly coupled to lattice distortions. and. as a consequence, the presence of other N adatoms introduces an anisotropy in the diffusion. Based on experimentally determined values of the diffusion barriers and adsorbate......-adsorbate: interactions, the potential energy surface experienced by a N adatom is determined....

76 FR 50881 - Required Scale Tests

Science.gov (United States)

2011-08-17

... RIN 0580-AB10 Required Scale Tests AGENCY: Grain Inspection, Packers and Stockyards Administration... required scale tests. Those documents defined ``limited seasonal basis'' incorrectly. This document... 20, 2011 (76 FR 3485) and on April 4, 2011 (76 FR 18348), concerning required scale tests. Those...

Measurement of N and C diffusion in Sm2Fe17 by magnetic relaxation

International Nuclear Information System (INIS)

Mommer, N.; Hirscher, M.; Gerlach, M.; Van Lier, J.; Kronmueller, H.; Kubis, M.; Mueller, K.-H.

1998-01-01

Magnetic after-effect (MAE) measurements of nitrided and carburized Sm 2 Fe 17 compounds were performed in the temperature range of 140 K to 480 K. Both nitrided and carburized compounds show relaxation maxima at 285 and 300 K, respectively, which are absent in pure Sm 2 Fe 17 compounds. Therefore, these relaxation maxima are attributed to jumps of interstitially dissolved nitrogen or carbon atoms. Numerical evaluation yielded an activation enthalpy Q N (0.84±0.05) eV and a pre-exponential factor τ 0 N =3.10 -15±1 s for the short-range diffusion of N atoms. The corresponding values for the carbon diffusion are Q C =(0.91±0.05) eV and τ 0 C =1.10 -15±1 s. The carbon and nitrogen content of the samples was determined from the increase in mass during nitrogenation or carburization to Sm 2 Fe 17 N 1.2 and Sm 2 Fe 17 C 2.6 . (orig.)

Fe3Nb3N precipitates of the Fe3W3C type in Nb stabilized ferritic stainless steel

International Nuclear Information System (INIS)

Malfliet, A.; Van den Broek, W.; Chassagne, F.; Mithieux, J.-D.; Blanpain, B.; Wollants, P.

2011-01-01

Highlights: → The precipitation in Nb stabilized ferritic stainless steel at 950 deg. C is investigated. → We characterized the Fe 3 Nb 3 X precipitates with SAED, EELS, WDS and AES. → We found that Fe 3 Nb 3 X precipitates are stabilized by N and not by C or O. → This insight is new and important for future development of this type of steel grade. - Abstract: A Nb stabilized ferritic stainless steel with 0.45 wt.%Nb, 82 ppm C and 170 ppm N is investigated to reveal the nature of the precipitates present at 950 deg. C. In particular, Fe 3 Nb 3 X precipitates of the Fe 3 W 3 C type are analyzed with WDS and EELS to determine the light elements X stabilizing this phase in the steel. According to WDS on large precipitates after 500 h at 950 deg. C, the Fe 3 Nb 3 X phase contains 10.4 at.% N, 1.2 at.% O and 1.0 at.% C. Auger Electron Spectroscopy on the same precipitates confirms the presence of N. In addition, it is revealed that the C and O peaks observed with WDS result from surface contamination as they disappear after Ar sputtering. The presence of a N peak in the EELS spectra of small Fe 3 Nb 3 X precipitates which have formed after 6 min at 950 deg. C indicate that N stabilizes this phase already from the initial precipitation stage. With this analysis it is demonstrated that N is an effective stabilizer of Fe 3 Nb 3 X precipitates in ferritic stainless steels. The formation of this phase should therefore be considered when predicting the precipitation behavior of Nb in industrial Nb stabilized ferritic stainless steels containing residual N.

Crystal structure and optical property of complex perovskite oxynitrides ALi0.2Nb0.8O2.8N0.2, ANa0.2Nb0.8O2.8N0.2, and AMg0.2Nb0.8O2.6N0.4 (A = Sr, Ba)

Science.gov (United States)

Moon, Keon Ho; Avdeev, Maxim; Kim, Young-Il

2017-10-01

Oxynitride type complex perovskites AM0.2Nb0.8O3-xNx (A = Sr, Ba; M = Li, Na, Mg) were newly synthesized by the solid state diffusion of Li+, Na+, or Mg2+ into the layered oxide, A5Nb4O15, with concurrent O/N substitution. Neutron and synchrotron X-ray Rietveld refinement showed that SrLi0.2Nb0.8O2.8N0.2, SrNa0.2Nb0.8O2.8N0.2, and SrMg0.2Nb0.8O2.6N0.4 had body-centered tetragonal symmetry (I4/mcm), while those with A = Ba had simple cubic symmetry (Pm 3 ̅ m). In the tetragonal Sr-compounds, the nitrogen atoms were localized on the c-axial 4a site. However, the octahedral cations, M/Nb (M = Li, Na, Mg) were distributed randomly in all six compounds. The lattice volume of AM0.2Nb0.8O3-xNx was dependent on various factors including the type of A and the electronegativity of M. Compared to the simple perovskites, ANbO2N (A = Sr, Ba), AM0.2Nb0.8O3-xNx had wider band gaps (1.76-2.15 eV for A = Sr and 1.65-2.10 eV for A = Ba), but significantly lower sub-gap absorption.

Irradiation data analysis and thermal analysis of the 02M-02K capsule for material irradiation test

International Nuclear Information System (INIS)

Choi, Myoung Hwan; Choo, K. N.; Kang, Y. H.; Kim, B. G.; Cho, M. S.; Sohn, J. M.; Shin, Y. T.; Park, S. J.; Kim, Y. J.

2004-11-01

In order to evaluate the fracture toughness of RPV materials, the material irradiation test using the instrumented capsule (02M-02K) were carried out in the HANARO in August 2003. Based on the user's requirements the thermal design analysis of the capsule 02M-02K was performed, and the specimens were suitably arranged in each step of the capsule main body. In this report, both the temperature data of specimens measured during irradiation test and the calculated data from the thermal analysis are compared and evaluated. Also, the temperature profile in each step with the HANARO reactor power and helium pressure is reviewed and evaluated. The effects of the gap size such as theoretically calculated from thermal expansion during irradiation test and measured one in the manufacturing of the capsule on the specimen temperature were reviewed. The thermal analysis was performed by using a Finite Element (FE) analysis program, ANSYS. Two-dimensional model for the 1/4 section of the capsule is generated, and the γ-heating rate of the materials used in the capsule at the control rod position of 430 mm is used as input data. The thermal analysis using a 3-dimensional model, which is quite similar to the actual shape of the capsule, is also conducted to obtain the temperature distribution in the axial direction. The analysis results show that the temperature difference between the top and bottom positions of a specimen is found to be smaller than 13.2 .deg. C. The maximum measured and calculated temperature in the step 3 of the capsule is 256 .deg. C and 264 .deg. C, respectively. The measured temperature data are obtained at the reactor power of 24 MW, the heater power of 0 W and the helium pressure of 760 torr. Generally, the temperature data obtained by the FE analysis are slightly lower than those of the measured except the step 1 of the capsule. However, the temperature difference between the measured and the calculated shows a good agreement within 9 percent. It is

Magnetic properties and tunable magneto-caloric effect in La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 (x = 0.3, 0.5, and 0.7) compounds

Science.gov (United States)

Wu, Qiming; Wang, Xiangjie; Ding, Zan; Li, Lingwei

2018-05-01

The magnetic and magneto-caloric properties in the ternary elementals doped La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 (x = 0.3, 0.5, and 0.7) compounds were studied. With the increases of Co content x, the Curie temperature TC increases and the thermal hysteresis decreases. All the compounds undergo a second-order magnetic phase transition and exhibit a considerable reversible tunable magneto-caloric effect. The values of maximum magnetic entropy change (-ΔSMmax) and the Relative Cooling Power (RCP) are kept at same high level with different Co content. Under a magnetic field change of 0-5 T, the values of -ΔSMmax for La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 are 10.5, 10.7, and 9.8 J/kg K for x = 0.3, 0.5, and 0.7, respectively. The corresponding values of RCP are 267.1, 289.9, and 290.2 J/kg.

New method for simultaneous determination of Fe(II) and Fe(III) in water using flow injection technique

International Nuclear Information System (INIS)

Kozak, J.; Gutowski, J.; Kozak, M.; Wieczorek, M.; Koscielniak, P.

2010-01-01

The method exploits the possibilities of flow injection gradient titration in a system of reversed flow with spectrophotometric detection. In the developed approach a small amount of titrant (EDTA) is injected into a stream of sample containing a mixture of indicators (sulfosalicylic acid and 1,10-phenanthroline). In acid environment sulfosalicylic acid forms a complex with Fe(III), whereas 1,10-phenanthroline forms a complex with Fe(II). Measurements are performed at wavelength λ = 530 nm when radiation is absorbed by both complexes. After injection EDTA replaces sulfosalicylic acid and forms with Fe(III) more stable colourless complex. As a result, a characteristic 'cut off' peak is registered with a width corresponding to the Fe(III) concentration and with a height corresponding to the Fe(II) concentration. Calibration was performed by titration of four two-component standard solutions of the Fe(II)/Fe(III) concentrations established in accordance with 2 2 factorial plan. The method was tested with the use of synthetic samples and then it was applied to the analysis of water samples taken from artesian wells. Under optimized experimental conditions Fe(II) and Fe(III) were determined with precision less than 0.8 and 2.5% (RSD) and accuracy less than 3.2 and 5.1% (relative error) within the concentration ranges of 0.1-3.0 and 0.9-3.5 mg L -1 of both analytes, respectively.

Growth and microstructure of iron nitride layers and pore formation in {epsilon}-Fe{sub 3}N

Energy Technology Data Exchange (ETDEWEB)

Middendorf, C.; Mader, W. [Univ. Bonn, Inst. fuer Anorganische Chemie, Bonn (Germany)

2003-03-01

Layers of {epsilon}-Fe{sub 3}N and {gamma}'-Fe{sub 4}N on ferrite were produced by nitriding iron single crystals or rolled sheets of iron in flowing ammonia at 520 C. The nitride layers were characterised using X-ray diffraction, light microscopy as well as scanning and transmission electron microscopy. The compound layer consists of {epsilon}-Fe{sub 3}N at the surface and of {gamma}'-Fe{sub 4}N facing the ferrite. After 4 h of nitriding, pores develop in the near surface region of {epsilon}-Fe{sub 3}N showing more or less open porosity. Growth of the entire compound layer as well as of the massive and the porous {epsilon}-Fe{sub 3}N sublayer is diffusion-controlled and follows a parabolic growth rate. The {gamma}'-Fe{sub 4}N layer is formed as a transition phase within a narrow interval of nitrogen activity, and it shows little growth in thickness. The transformation of {gamma}'-Fe{sub 4}N to {epsilon}-Fe{sub 3}N is topotactic, where the orientation of the closed-packed iron layers of the crystal structures is preserved. Determination of lattice plane spacings was possible by X-ray diffraction, and this was correlated to the nitrogen content of {epsilon}-Fe{sub 3}N. While the porous layer exhibits an enhanced nitrogen content corresponding to the chemical composition Fe{sub 3}N{sub 1.1}, the massive e Fe{sub 3}N layer corresponds to Fe{sub 3}N{sub 1.0}. The pore formation in {epsilon}-Fe{sub 3}N{sub 1.1} is concluded to be the result of excess nitrogen atoms on non-structural sites, which have a high mobility. Therefore, recombination of excess nitrogen to molecular N{sub 2} at lattice defects is preferred in {epsilon}-Fe{sub 3}N with high nitrogen content compared to stoichiometric {epsilon}-Fe{sub 3}N{sub 1.0} with nitrogen on only structural sites. (orig.)

Fe(III)-TAML activator: a potent peroxidase mimic for chemiluminescent determination of hydrogen peroxide.

Science.gov (United States)

Vdovenko, Marina M; Demiyanova, Alexandra S; Kopylov, Kirill E; Sakharov, Ivan Yu

2014-07-01

Efforts to replace native peroxidase with its low molecular weight alternatives have stimulated a search for peroxidase mimetics. Herein we describe the oxidation of luminol with hydrogen peroxide catalyzed by commercially available Fe(III)-TAML activator 1a, which was shown to be a more active catalyst than hemin. At Fe(III)-TAML activator 1a use in chemiluminescent assay for H2O2 determination the detection limit value (3σ) of 5×10(-8)M was similar to the detection limit obtained with horseradish peroxidase (1×10(-7)M) and significantly lower than that obtained in the presence of hemin (6×10(-7)M). The linear ranges (R(2)=0.98) of the assay were 6×10(-8)-1×10(-6)M and 6×10(-7)-1×10(-6)M H2O2 for Fe(III)-TAML 1a and hemin, respectively. The CV values for Fe(III)-TAML 1a-based assay measured within the working range varied from 1.0% to 3.7% (n=4), whereas in the case of hemin -5.0% to 9.7% (n=4). Moreover, the sensitivity of Fe(III)-TAML 1a-based method was 56 and 5 times higher than that of hemin- and HRP-based methods, respectively. The obtained results open good perspectives to apply Fe(III)-TAML activator 1a in CL analytical methods instead of hemin, a traditionally used peroxidase mimetic. Copyright © 2014 Elsevier B.V. All rights reserved.

FE02 and visual observation for a CTBT OSI

International Nuclear Information System (INIS)

Kuang, F.

2004-01-01

FE02 field experiment conducted in Kazakhstan provided useful experience according to different OSI procedures. The effectiveness of conducting a visual observation during an OSI affects the accomplishment of the inspection mandate directly and substantially. The paper gives description of basic functions, stages and visual observation peculiarities at OSI pseudo-real and real scenario. An essential question on basic requirements to visual inspectors was also reviewed. (author)

Temperature-dependent impedance spectroscopy of La0.8Sr0.2FeO3 nano-crystalline material

Science.gov (United States)

Kafa, C. A.; Triyono, D.; Laysandra, H.

2017-04-01

LaFeO3 is a material with perovskite structure which electrical properties frequently investigated. Research are done due to the exhibition of excellent gas sensing behavior through resistivity comparison from the p-type semiconductor. Sr doping on LaFeO3 or La1-xSrxFeO3 are able to improve the electrical conductivity through structural modification. Using Sr dopant concentration (x) of 0.2, La0.8Sr0.2FeO3 nano-crystal pellet was synthesized. The synthesis used sol-gel method, followed by gradual heat treatment and uniaxial compaction. XRD characterization shows that the structure of the sample is Orthorhombic Perovskite. Topography of the sample by SEM reveals grain and grain boundary existence with emerging agglomeration. The electrical properties of the material, as functions of temperature and frequency, were measured by Impedance Spectroscopy method using RLC meter, for temperatures of 303-373K. Through the Nyquist plot and Bode plot, the electrical conductivity of La0.8Sr0.2FeO3 is contributed by the grain and grain boundary. Finally, the electrical permittivities of La0.8Sr0.2FeO3 are increasing with temperature increase, with the highest achieved when measured at 1 kHz frequency.

In-plain electric properties of [CaMnO3/REMO3] (RE=Bi, La M=Fe, Fe0.8Mn0.2) superlattices grown by pulsed laser deposition method

NARCIS (Netherlands)

Iwata, N.; Watabe, Y.; Oikawa, T.; Takase, K.; Huijben, Mark; Inaba, T.; Oshima, K.; Rijnders, Augustinus J.H.M.; Yamamoto, H.

2014-01-01

The [CaMnO3 (CMO)/REMO3] (RE = Bi, La M = Fe, Fe0.8Mn0.2) superlattices show semiconducting behavior with transition temperatures (TEg) of 71, 127, and 151 K in the [CMO/BiFe0.8Mn0.2O3], [CMO/BiFeO3], and [CMO/LaFeO3] superlattices. The formation of a magnetic polaron is expected in the CMO layer of

Statistical modeling of the reactions Fe(+) + N2O → FeO(+) + N2 and FeO(+) + CO → Fe(+) + CO2.

Science.gov (United States)

Ushakov, Vladimir G; Troe, Jürgen; Johnson, Ryan S; Guo, Hua; Ard, Shaun G; Melko, Joshua J; Shuman, Nicholas S; Viggiano, Albert A

2015-08-14

The rates of the reactions Fe(+) + N2O → FeO(+) + N2 and FeO(+) + CO → Fe(+) + CO2 are modeled by statistical rate theory accounting for energy- and angular momentum-specific rate constants for formation of the primary and secondary cationic adducts and their backward and forward reactions. The reactions are both suggested to proceed on sextet and quartet potential energy surfaces with efficient, but probably not complete, equilibration by spin-inversion of the populations of the sextet and quartet adducts. The influence of spin-inversion on the overall reaction rate is investigated. The differences of the two reaction rates mostly are due to different numbers of entrance states (atom + linear rotor or linear rotor + linear rotor, respectively). The reaction Fe(+) + N2O was studied either with (6)Fe(+) or with (4)Fe(+) reactants. Differences in the rate constants of (6)Fe(+) and (4)Fe(+) reacting with N2O are attributed to different contributions from electronically excited potential energy surfaces, such as they originate from the open-electronic shell reactants.

Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}: Two stannide intermetallics with low-dimensional iron sublattices

Energy Technology Data Exchange (ETDEWEB)

Calta, Nicholas P. [Department of Chemistry, Northwestern University (United States); Kanatzidis, Mercouri G., E-mail: m-kanatzidis@northwestern.edu [Department of Chemistry, Northwestern University (United States); Materials Science Division, Argonne National Laboratory (United States)

2016-04-15

This article reports two new Hf-rich intermetallics synthesized using Sn flux: Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}. Hf{sub 3}Fe{sub 4}Sn{sub 4} adopts an ordered variant the Hf{sub 3}Cu{sub 8} structure type in orthorhombic space group Pnma with unit cell edges of a=8.1143(5) Å, b=8.8466(5) Å, and c=10.6069(6) Å. Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}, on the other hand, adopts a new structure type in Cmc2{sub 1} with unit cell edges of a=5.6458(3) Å, b=35.796(2) Å, and c=8.88725(9) Å for x=0. It exhibits a small amount of phase width in which Sn substitutes on one of the Fe sites. Both structures are fully three-dimensional and are characterized by pseudo one- and two-dimensional networks of Fe–Fe homoatomic bonding. Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} exhibits antiferromagnetic order at T{sub N}=46(2) K and its electrical transport behavior indicates that it is a normal metal with phonon-dictated resistivity. Hf{sub 3}Fe{sub 4}Sn{sub 4} is also an antiferromagnet with a rather high ordering temperature of T{sub N}=373(5) K. Single crystal resistivity measurements indicate that Hf{sub 3}Fe{sub 4}Sn{sub 4} behaves as a Fermi liquid at low temperatures, indicating strong electron correlation. - Graphical abstract: Slightly different growth conditions in Sn flux produce two new intermetallic compounds: Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}. - Highlights: • Single crystals of both Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} were grown using Sn flux. • The crystal structures were determined using single crystal X-ray diffraction. • The Fe moments in Hf{sub 3}Fe{sub 4}Sn{sub 4} display AFM order below T{sub N}=373 K. • The Fe moments in Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} display AFM order below T{sub N}=46 K.

Photoexcited carrier trapping and recombination at Fe centers in GaN

International Nuclear Information System (INIS)

Uždavinys, T. K.; Marcinkevičius, S.; Leach, J. H.; Evans, K. R.; Look, D. C.

2016-01-01

Fe doped GaN was studied by time-resolved photoluminescence (PL) spectroscopy. The shape of PL transients at different temperatures and excitation powers allowed discrimination between electron and hole capture to Fe"3"+ and Fe"2"+ centers, respectively. Analysis of the internal structure of Fe ions and intra-ion relaxation rates suggests that for high repetition rates of photoexciting laser pulses the electron and hole trapping takes place in the excited state rather than the ground state of Fe ions. Hence, the estimated electron and hole capture coefficients of 5.5 × 10"−"8 cm"3/s and 1.8 × 10"−"8 cm"3/s should be attributed to excited Fe"3"+ and Fe"2"+ states. The difference in electron capture rates determined for high (MHz) and low (Hz) (Fang et al., Appl. Phys. Lett. 107, 051901 (2015)) pulse repetition rates may be assigned to the different Fe states participating in the carrier capture. A weak temperature dependence of the electron trapping rate shows that the potential barrier for the multiphonon electron capture is small. A spectral feature observed at ∼420 nm is assigned to the radiative recombination of an electron in the ground Fe"2"+ state and a bound hole.

Synthesis of single-phase L10-FeNi magnet powder by nitrogen insertion and topotactic extraction

OpenAIRE

Goto, Sho; Kura, Hiroaki; Watanabe, Eiji; Hayashi, Yasushi; Yanagihara, Hideto; Shimada, Yusuke; Mizuguchi, Masaki; Takanashi, Koki; Kita, Eiji

2017-01-01

Tetrataenite (L10-FeNi) is a promising candidate for use as a permanent magnet free of rare-earth elements because of its favorable properties. In this study, single-phase L10-FeNi powder with a high degree of order was synthesized through a new method, nitrogen insertion and topotactic extraction (NITE). In the method, FeNiN, which has the same ordered arrangement as L10-FeNi, is formed by nitriding A1-FeNi powder with ammonia gas. Subsequently, FeNiN is denitrided by topotactic reaction to ...

EFAM GTP-CREEP 02 - the GKSS test procedure for determining the creep crack extension of materials

International Nuclear Information System (INIS)

Schwalbe, K.H.

2002-01-01

This document describes a fracture mechanics method in procedural form for determining the creep crack extension of materials. It is based on the unified fracture mechanics test method EFAM GTP 02, the ASTM standard E 1457-98, activities of VAMAS TWA 19, and GKSS experience in creep crack extension testing. It introduces novel features such as the rate of the δ 5 crack tip opening displacement, the crack tip opening angle, and the middle cracked tension specimen. (orig.) [de

Permanent magnets prepared from Sm10.5Fe88.5Zr1.0Ny without homogenization

International Nuclear Information System (INIS)

Gebel, B.; Kubis, M.; Mueller, K.-H.

1997-01-01

In as-cast Sm 2 Fe 17 the high amount of α-Fe caused by a peritectic reaction can be considerably reduced by a small addition of about 1 at% Zr. X-ray diffraction showed that as-cast Sm 10.5 Fe 88.5 Zr 1.0 mainly consists of a phase with the Th 2 Zn 17 -type structure and SmFe 3 . Non-homogenized Sm 10.5 Fe 88.5 Zr 1.0 was milled and (i) annealed in vacuum or (ii) treated with a hydrogenation-disproportionation-desorp tion-recombination (HDDR) process. The annealed and subsequently nitrogenated powder is magnetically anisotropic and has a coercivity μ 0J H C up to 2.0 T and an energy product (BH) max up to 136 kJ/m 3 . HDDR-treated and nitrogenated powder is isotropic and exhibits values of μ 0J H C = 3.1 T and (BH) max 103 kJ/m 3 . Consequently, Sm 10.5 Fe 88.5 Zr 1.0 N y (y ∼ 16) permanent magnets with very good properties can be prepared without the time-consuming homogenization procedure. (orig.)

Intrinsic Properties of Fe-Substituted L1(0) Magnets

Energy Technology Data Exchange (ETDEWEB)

Manchanda, P; Kumar, P; Kashyap, A; Lucis, MJ; Shield, JE; Mubarok, A; Goldstein, JI; Constantinides, S; Barmak, K; Lewis, LH; Sellmyer, DJ; Skomski, R

2013-10-01

First-principle supercell calculations are used to determine how 3d elemental additions, especially Fe additions, modify the magnetization, exchange and anisotropy of L1(0)-ordered ferromagnets. Calculations are performed using the VASP code and partially involve configurational averaging over site disorder. Three isostructural systems are investigated: Fe-Co-Pt, Mn-Al-Fe, and transition metal-doped Fe-Ni. In all three systems the iron strongly influences the magnetic properties of these compounds, but the specific effect depends on the host. In CoPt(Fe) iron enhances the magnetization, with subtle changes in the magnetic moments that depend on the distribution of the Fe and Co atoms. The addition of Fe to MnAl is detrimental to the magnetization, because it creates antiferromagnetic exchange interactions, but it enhances the magnetic anisotropy. The replacement of 50% of Mn by Fe in MnFeAl2 enhances the anisotropy from 1.77 to 2.5 MJ/m(3). Further, the substitution of light 3d elements such as Ti, V, Cr into L1(0)-ordered FeNi is shown to substantially reduce the magnetization.

Magnetoresistance properties of Fe0,2C0,8 composite materials pre and post gamma irradiated at 250 kGy dose

International Nuclear Information System (INIS)

Yunasfi; Setyo Purwanto; Wisnu A A

2009-01-01

Research about change of, magnetoresistance properties of Fe 0,2 C 0,8 composite materials pre and post gamma irradiation at a dose of 250 kGy was carried out. Fe 0,2 C 0,8 was prepared by mixing of Fe and C powder with the ratio of Fe : C set on 20:80 in weight %. In this research, the phase structure and magnetic properties of Fe 0,2 C 0,8 composite materials after 250 KGy dose of gamma irradiation have been measured and analyzed. The phase structure of Fe 0,2 C 0,8 was analyzed using X-ray diffractometer (XRD), whole the magnetoresistance properties was characterized using Four Point Probe method. The analyzing results showed the decreasing of X-ray diffraction peak intensity, but also in the same time showed the increasing of magnetoresistance properties after gamma irradiation. The enhancement of magnetoresistance value reached 5 times at 7,5 kOe magnetic field. This enhancement was caused due to structure defect within Fe 0,2 C 0,8 composite initiated by interaction between radiation of gamma ray and composite materials that further causes a change of magnetic interaction intensity in this materials. (author)

Modeling thermodynamics of Fe-N phases; characterisation of e-Fe2N1-z

DEFF Research Database (Denmark)

Pekelharing, M.I.; Böttger, A.; Somers, Marcel A.J.

1999-01-01

In order to arrive at modeling the thermodynamics of Fe-N phases, including long-range (LRO) and short-range ordering (SRO) of the N atoms, it is important to understand the role of N interstitially dissolved in an Fe-host lattice. The crystal structure of -Fe2N1-z consists of an h.c.p. iron...... sublattice and a hexagonal nitrogen sublattice formed by octahedral interstices of the Fe sublattice [1]. Two ground-state structures have been proposed for the ordered arrangement of the N atoms on their own sublattice [1], which were shown to be thermodynamically favourable [2]: configuration A for Fe2N1...... investigated with X-ray diffraction (XRD) and Mössbauer spectroscopy. A thermodynamic model accounting for the two configurations of LRO of the N atoms [2,3] was fitted to the N-absorption isotherm at 723 K and resulted in the occupancies of the sites of the nitrogen sublattice. A miscibility gap between...

Structural investigation and microwave characteristics of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing materials

Energy Technology Data Exchange (ETDEWEB)

Manaf, Azwar [Dept. of Physics, Faculty of Mathematics and Natural Sciences, Indonesia of University (Indonesia); Adi, Wisnu Ari, E-mail: dwisnuaa@batan.go.id [Center for Technology of Nuclear Industry Material, National Nuclear Energy Agency (Indonesia)

2014-03-24

Synthesis and characterization of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing material by mechanical alloying process has been performed. The absorbing material was prepared by oxide materials, namely BaCO{sub 3}, La{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, and MnCO{sub 3}. The mixture was milled for 10 h and then sintered at a temperature of 1000 ° C for 10 h. The refinement results of x-ray diffraction pattern of lanthanum manganite substituted with barium showed that the sample consisted of two phases, namely, La{sub 0.9125}MnO{sub 3} phase which has a structure monoclinic (I12/a1) with lattice parameters a = 5.527(1) Å, b = 5.572(1) Å and c = 7.810(1) Å, α = γ = 90° and β = 89.88(5)°, the unit cell volume of V = 240.57(8) Å{sup 3}, and the atomic density of ρ = 6.238 gr.cm{sup −3}. The microstructure analyses showed that the particle shapes was polygonal with the varied particle sizes of 1 ∼ 3 μm distributed homogeneously on the surface of the samples. The results of the electromagnetic wave absorption curve analysis by using a vector network analyzer (VNA) showed that the sample can absorb microwaves in the frequency range of 8-15 GHz with a very wide absorption bandwidth. It indicates that the as prepared absorber presents potential absorbing property in X and Ku-band. We concluded that the (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} material can be applied as a candidate absorber material of microwaves or electromagnetic wave.

Epitaxial Fe16N2 thin film on nonmagnetic seed layer

Science.gov (United States)

Hang, Xudong; Zhang, Xiaowei; Ma, Bin; Lauter, Valeria; Wang, Jian-Ping

2018-05-01

Metastable α″ -Fe16N2 has attracted much interest as a candidate for rare-earth-free hard magnetic materials. We demonstrate that Fe16N2 thin films were grown epitaxially on Cr seed layers with MgO (001) substrates by facing-target sputtering. Good crystallinity with the epitaxial relation MgO (001 )[110 ] ∥ Cr (001 )[100 ] ∥ Fe16N2 (001 )[100 ] was obtained. The chemical order parameter, which quantifies the degree of N ordering in the Fe16N2 (the N-disordered phase is α' -Fe8N martensite), reaches 0.75 for Cr-seeded samples. Cr has a perfect lattice constant match with Fe16N2, and no noticeable strain can be assigned to Fe16N2. The intrinsic saturation magnetization of this non-strained Fe16N2 thin film at room temperature is determined to be 2.31 T by polarized neutron reflectometry and confirmed with vibrating sample magnetometry. Our work provides a platform to directly study the magnetic properties of high purity Fe16N2 films with a high order parameter.

Cone Penetrometer N Factor Determination Testing Results

Energy Technology Data Exchange (ETDEWEB)

Follett, Jordan R.

2014-03-05

This document contains the results of testing activities to determine the empirical 'N Factor' for the cone penetrometer in kaolin clay simulant. The N Factor is used to releate resistance measurements taken with the cone penetrometer to shear strength.

Synthesis of nanocrystalline nickel-zinc ferrite (Ni0.8Zn0.2Fe2O4) thin films by chemical bath deposition method

International Nuclear Information System (INIS)

Pawar, D.K.; Pawar, S.M.; Patil, P.S.; Kolekar, S.S.

2011-01-01

Graphical abstract: Display Omitted Research highlights: → We have successfully synthesized nickel-zinc ferrite (Ni 0.8 Zn 0.2 Fe 2 O 4 ) thin films on stainless steel substrates using a low temperature chemical bath deposition method. → The surface morphological study showed the compact flakes like morphology. → The as-deposited thin films are hydrophilic (10 o o ) whereas the annealed thin films are super hydrophilic (θ o ) in nature. → Ni 0.8 Zn 0.2 Fe 2 O 4 thin films could be used in supercapacitor. - Abstract: The nickel-zinc ferrite (Ni 0.8 Zn 0.2 Fe 2 O 4 ) thin films have been successfully deposited on stainless steel substrates using a chemical bath deposition method from alkaline bath. The films were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), static water contact angle and cyclic voltammetry measurements. The X-ray diffraction pattern shows that deposited Ni 0.8 Zn 0.2 Fe 2 O 4 thin films were oriented along (3 1 1) plane. The FTIR spectra showed strong absorption peaks around 600 cm -1 which are typical for cubic spinel crystal structure. SEM study revealed compact flakes like morphology having thickness ∼1.8 μm after air annealing. The annealed films were super hydrophilic in nature having a static water contact angle (θ) of 5 o .The electrochemical supercapacitor study of Ni 0.8 Zn 0.2 Fe 2 O 4 thin films has been carried out in 6 M KOH electrolyte. The values of interfacial and specific capacitances obtained were 0.0285 F cm -2 and 19 F g -1 , respectively.

Synthesis and Characterization of Polyol-Assisted Nano Cu0.2Ni0.2Sn0.2Ba0.4 Fe2O4 by a Wet Hydroxyl Route

Science.gov (United States)

Pavithradevi, S.; Suriyanarayanan, N.; Boobalan, T.; Velumani, S.; Chandramohan, M.; Manivel Raja, M.

2017-08-01

Nanocrystalline spinel ferrite of composition Cu0.2Ni0.2Sn0.2Ba0.4 Fe2O4 has been synthesized by a wet hydroxyl chemical route in ethylene glycol as chelating agent and sodium hydroxide as precipitator at pH 8. Ethylene glycol has been used as the medium which serves as the solvent as well as a complexing agent. The synthesized particles are annealed at temperatures of 350°C, 700°C, and 1050°C. Thermogravimetric (TG) analysis confirms that at 240°C, ethylene glycol has evaporated completely, and a stable phase is formed above 670°C. Fourier transform infrared (FT-IR) spectroscopy of mixed Cu0.2Ni0.2Sn0.2Ba0.4 ferrite nanoparticles like as synthesized and annealed at 1050°C are recorded between 400 cm-1 and 4000 cm-1. FT-IR appraises the structural formation of Cu0.2Ni0.2Sn0.2Ba0.4 Fe2O4 between the as-synthesized sample and the sample annealed at 1050°C. Structural characterizations of all the samples are carried out by x-ray diffraction (XRD) technique. XRD reveals that the particle size increases with the increase in annealing temperatures. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) confirms that the particles are flaky and spherical with the crystallite size in the range of 11-27 nm. The decrement of dielectric properties, like dielectric constant and dielectric loss, with the increment of frequency as seen in all the samples is an usual dielectric behavior of spinel ferrites. The lack of net magnetization is noticed immediately when the applied magnetic field is removed which prompts superparamagnetic behavior, as seen in all the samples.

Spin-dependent electronic transport characteristics in Fe4N/BiFeO3/Fe4N perpendicular magnetic tunnel junctions

Science.gov (United States)

Yin, Li; Wang, Xiaocha; Mi, Wenbo

2018-01-01

Perpendicular magnetic tunnel junctions (MTJs) have attracted increasing attention owing to the low energy consumption and wide application prospects. Herewith, against Julliere's formula, an inverse tunnel magnetoresistance (TMR) appears in tetragonal Fe4N/BiFeO3/Fe4N perpendicular MTJs, which is attributed to the binding between the interface resonant tunneling state and central (bordered) hot spots. Especially, antiferromagnetic BiFeO3 shows an extra spin-polarized resonant state in the barrier, which provides a magnetic-barrier factor to affect the tunneling transport in MTJs. Meanwhile, due to the spin-polarized transport in Fe4N/BiFeO3/Fe4N MTJs, the sign of TMR can be tuned by the applied bias. The tunable TMR and resonant magnetic barrier effect pave the way for clarifying the tunneling transport in other junctions and spintronic devices.

Measurement of N and C diffusion in Sm{sub 2}Fe{sub 17} by magnetic relaxation

Energy Technology Data Exchange (ETDEWEB)

Mommer, N.; Hirscher, M.; Gerlach, M.; Van Lier, J.; Kronmueller, H. [Max-Planck-Institut fuer Metallforschung, Stuttgart (Germany); Kubis, M.; Mueller, K.-H. [Institut fuer Festkoerper und Werkstofforschung, Institut fuer Metallische Werkstoffe, D-01171 Dresden (Germany)

1998-10-02

Magnetic after-effect (MAE) measurements of nitrided and carburized Sm{sub 2}Fe{sub 17} compounds were performed in the temperature range of 140 K to 480 K. Both nitrided and carburized compounds show relaxation maxima at 285 and 300 K, respectively, which are absent in pure Sm{sub 2}Fe{sub 17} compounds. Therefore, these relaxation maxima are attributed to jumps of interstitially dissolved nitrogen or carbon atoms. Numerical evaluation yielded an activation enthalpy Q{sup N} (0.84{+-}0.05) eV and a pre-exponential factor {tau}{sub 0}{sup N}=3.10{sup -15{+-}1} s for the short-range diffusion of N atoms. The corresponding values for the carbon diffusion are Q{sup C}=(0.91{+-}0.05) eV and {tau}{sub 0}{sup C}=1.10{sup -15{+-}1} s. The carbon and nitrogen content of the samples was determined from the increase in mass during nitrogenation or carburization to Sm{sub 2}Fe{sub 17}N{sub 1.2} and Sm{sub 2}Fe{sub 17}C{sub 2.6}. (orig.) 18 refs.

Colorimeter determination of Fe(II)/Fe(III) ratio in glass

International Nuclear Information System (INIS)

Baumann, E.W.; Coleman, C.J.; Karraker, D.G.; Scott, W.H.

1987-01-01

A colorimetric method has been developed to determine the Fe(II)/Fe(III) ratio in glass containing nuclear waste. Fe(II) is stabilized with pentavalent vanadium during dissolution in sulfuric and hydrofluoric acids. The chromogen is FerroZine (Hach Chemical Company), which forms a magenta complex with Fe(II). The two-step color development consists of determining the Fe(II) by adding FerroZine, followed by determining total Fe after the Fe(III) present is reduced with ascorbic acid. The method was validated by analyzing mixtures of ferrous/ferric solutions and nonferrous glass frit, and by comparison with Moessbauer spectroscopy. The effect of gamma radiation was established. The procedure is generally applicable to nonradioactive materials such as minerals and other glasses

Magnetic ordering and electrical resistivity in Co0.2Zn0.8Fe2O4 spinel oxide

International Nuclear Information System (INIS)

Bhowmik, R.N.; Ranganathan, R.; Ghosh, B.; Kumar, S.; Chattopadhyay, S.

2008-01-01

We report the magnetic, Moessbauer spectroscopy and resistivity measurements in order to understand the electronic behaviour of bulk Co 0.2 Zn 0.8 Fe 2 O 4 spinel oxide. The effect of magnetic order on electrical behaviour is observed from the resistivity measurements in the absence and presence of magnetic field. The analysis of Moessbauer spectra suggests the absence of Fe 2+ ions in the system, which implies that complete hopping of charge carriers between localized Fe 3+ /Co 2+ and Fe 2+ /Co 3+ pair of ions in B sublattice is not the favourable mechanism in Co 0.2 Zn 0.8 Fe 2 O 4 . We suggest that electrical behaviour of the present sample may be consistent with a model of fractional charge transfer via Fe B 3+ -O 2- -Co B 2+ superexchange path

Kinetic method for determination of molybdenum(6) and tungsten(6) from oxidaton of O-aminophenol with hydrogen peroxide

International Nuclear Information System (INIS)

Krejngol'ts, S.U.; Vasnev, A.N.

1978-01-01

A new method for determination of Mo(6) and W(6), based on the oxidation of O-aminophenol with hydrogen peroxide, catalysed by Mo and W(6) ions, is suggested. The reaction takes place in the neutral medium at a rather high substrate concentrations. The 1.5 M acetate buffer solution, 0.2N EDTA and 0.1M solution of O-aminophenol in 0.1M HCl were suggested for determination of Mo (0.2N EDTA was used for Fe(3) camouflage). The 1.5M acetate buffer solution with 0.3M K 2 C 2 O 4 xH 2 O additions, for Fe(3) and Mo(6) camouflage, and 0.1M O-aminophenol solution in 0.1M solution of H 2 C 2 O 4 xH 2 O were used for tungsten determination. The range for Mo and W determination is 3x10 -3 and 1x10 -2 mkg/ml respectively. The range of Mo and W concentrations under determination is from 3x10 -3 -10 -2 to 2 mkg/ml. The techniques for the analysis of highly pure substances is developed

The investigation of Fe-Mn-based alloys with shape memory effect by small-angle scattering of polarized neutrons

International Nuclear Information System (INIS)

Kopitsa, G.P.; Runov, V.V.; Grigoriev, S.V.; Bliznuk, V.V.; Gavriljuk, V.G.; Glavatska, N.I.

2003-01-01

The small-angle polarized neutron scattering (SAPNS) technique has been used to study a nuclear and magnetic homogeneity in the distribution of both substituent (Si, Cr, Ni) and interstitial (C, N) alloying elements on the mesoscopic range in Fe-Mn-based alloys with shape memory effect (SME). The four groups of alloys with various basic compositions: FeMn 18 (wt%), FeMn 20 Si 6 , FeMn 20 Cr 9 N 0.2 and FeMn 17 Cr 9 Ni 4 Si 6 were investigated. It was found that the small-angle scattering of neutrons and depolarization on these alloys are very small altogether. The scattering did not exceed 1.5% from the incident beam and depolarization ∼2% for all samples. It means that these alloys are well nuclear and magnetically homogeneous on the scale of 10-1000 A. However, the difference in the homogeneity depending on the compositions still takes place. Thus, the adding of Si in FeMn 18 and FeMn 20 Cr 9 N 0.2 alloys improves the homogeneity pronouncedly. At once, the effect of the doping by C or N atoms on the homogeneity in FeMn 20 Si 6 and FeMn 17 Cr 9 Ni 4 Si 6 alloys is multivalued and depend on the presence of substitutional atoms (Ni and Cr). The capability of SAPNS as a method for the study of mesoscopic homogeneity in materials with SME and testing of the quality of their preparation is discussed

Determination of Cu, Fe, Zn Elements in Soil, Root Tea Plants, Tea Leaves, and Tea Beverage

International Nuclear Information System (INIS)

Supriyanto; Zainul-Kamal

2006-01-01

One of the causes of land quality damage was due to the pollution of Cu, Fe, and Zn so that it could directly and also indirectly cause the occurrence of pollution of plants which is growing on it for example tea plant that has been used by society for making of tea beverage. The sampling of soil, root tea plants, tea leaves and tea beverage samples were done in June, 2005 at sub district of Keparakan, Temanggung, Central Java. The purpose of research was to determine the content of Cu, Fe and Zn in soil, root tea plants, tea leaves and tea beverage. The research was done by digesting the sample with nitric acid until the clear solution was obtained, then it was added by aquabidest until 10.0 ml. Determination of Cu, Fe and Zn content used AAS instrument. The average concentration of Cu Fe and Zn obtained in deep soil samples area 0.155 ± 0.005 ppm, 127.16 ± 2.65 ppm, and 0.68 ± 0.02 ppm respectively, in surface soil samples are 0.355 ± 0.025 ppm, 360.59 ± 13.17 ppm and 0.78 ± 0.01 ppm respectively, in root of tea plants samples area 0.241 ± 0.098 ppm, 13.16 ± 1.34 ppm and 2.64 ± 0.06 ppm respectively, in tea leaves are 0.211 ± 0.013 ppm, 3.35 ± 0.886 ppm, and 0.795 ± 0.016 ppm respectively and in tea beverage 0.142 ± 0.086 ppm, 6.11 ± 0.35 ppm and 0.66 ± 0.02 ppm respectively. (author)

[Determination of Total Iron and Fe2+ in Basalt].

Science.gov (United States)

Liu, Jian-xun; Chen, Mei-rong; Jian, Zheng-guo; Wu, Gang; Wu, Zhi-shen

2015-08-01

Basalt is the raw material of basalt fiber. The content of FeO and Fe2O3 has a great impact on the properties of basalt fibers. ICP-OES and dichromate method were used to test total Fe and Fe(2+) in basalt. Suitable instrument parameters and analysis lines of Fe were chosen for ICP-OES. The relative standard deviation (RSD) of ICP-OES is 2.2%, and the recovery is in the range of 98%~101%. The method shows simple, rapid and highly accurate for determination of total Fe and Fe(2+) in basalt. The RSD of ICP-OES and dichromate method is 0.42% and 1.4%, respectively.

MIL-100-Fe derived N-doped Fe/Fe3C@C electrocatalysts for efficient oxygen reduction reaction

Science.gov (United States)

Guo, Dakai; Han, Sancan; Wang, Jiacheng; Zhu, Yufang

2018-03-01

N-doped porous Fe/Fe3C@C electrocatalysts were prepared by the pyrolysis of the hexamethylenetetramine (HMT)-incorporated MIL-100-Fe at different temperatures (700-1000 °C) under N2 atmosphere. Rotary evaporation of MIL-100-Fe and HMT solution could make more N-enriched HMT molecules enter into the pores of MIL-100-Fe, thus improving nitrogen contents of the final pyrolyzed samples. All pyrolyzed samples show porous textures with middle specific surface areas. The X-ray photoelectron spectroscopy (XPS) results demonstrate the successful introduction of N atoms into carbon framework. Sample Fe-N2-800 prepared by annealing the precursors with the HMT/MIL-100-Fe weight ratio of 2 at 800 °C exhibits the best electrocatalytic activity towards the oxygen reduction reaction (ORR) in terms of onset potential and current density because of high graphitic N and pyridinic N content. The enwrapped Fe/Fe3C nanoparticles and Fe-Nx active sites in these samples could also boost the ORR activity synergistically. Moreover, sample Fe-N2-800 demonstrates a dominant four electron reduction process, as well as excellent long-term operation stability and methanol crossover resistance. Thus, the N-doped Fe/Fe3C@C composites derived from the HMT-incorporated MIL-100-Fe are promising electrocatalysts to replace Pt/C for ORR in practical applications.

Preferential growth in FeCoV/Ti:N multilayers

Energy Technology Data Exchange (ETDEWEB)

Clemens, D.; Senthil Kumar, M.; Boeni, P.; Horisberger, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-09-01

The preferential growth in Fe{sub 0.50}Co{sub 0.48}V{sub 0.02}/Ti:N multilayers was studied by X-ray diffraction. X-ray specular reflectometry and subsequent simulation of the spectra was used to extract information about the thickness and interface roughness of individual layers. The investigation gives structural information about the material combination and its potential for the use of neutron polarizers. (author) 2 figs., 1 tab., 2 refs.

Measurement of 54Fe(n,2n)53Fe cross section near threshold

International Nuclear Information System (INIS)

Smither, R.K.; Greenwood, L.R.

1984-01-01

A series of experiments were performed at the Princeton Plasma Physics Laboratory to measure the cross section of the 54 Fe(n,2n) 53 Fe reaction near threshold. Measurements were made at 6 different neutron energies and cover the 1 MeV energy range from threshold (13.64 MeV) to 14.64 MeV. The 54 Fe(n,2n) cross section was measured relative to the 27 Al(n,p) 27 Mg cross section to an accuracy of a few percent. These accurate cross-section measurements will be useful in calculating damage caused by 14 MeV D-T plasma neutrons in Fe and calculating the production of the long-lived 53 Mn nuclei that account for much of the buildup of long-lived radioactivity in steel structures and other ferrous materials used in the construction of fusion reactors. They will also play an important part in a new method for measuring the plasma ion temperature of a D-T plasma

Synthesis of nanocrystalline nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films by chemical bath deposition method

Energy Technology Data Exchange (ETDEWEB)

Pawar, D.K. [Department of Chemistry, Shivaji University, Kolhapur 416 004 (M.S.) (India); Pawar, S.M. [Department of Materials Science and Engineering, Chonnam National University, 500 757 (Korea, Republic of); Patil, P.S. [Department of Physics, Shivaji University, Kolhapur 416 004 (M.S.) (India); Kolekar, S.S., E-mail: kolekarss2003@yahoo.co.in [Department of Chemistry, Shivaji University, Kolhapur 416 004 (M.S.) (India)

2011-02-24

Graphical abstract: Display Omitted Research highlights: > We have successfully synthesized nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films on stainless steel substrates using a low temperature chemical bath deposition method. > The surface morphological study showed the compact flakes like morphology. > The as-deposited thin films are hydrophilic (10{sup o} < {theta} < 90{sup o}) whereas the annealed thin films are super hydrophilic ({theta} < 10{sup o}) in nature. > Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films could be used in supercapacitor. - Abstract: The nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films have been successfully deposited on stainless steel substrates using a chemical bath deposition method from alkaline bath. The films were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), static water contact angle and cyclic voltammetry measurements. The X-ray diffraction pattern shows that deposited Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films were oriented along (3 1 1) plane. The FTIR spectra showed strong absorption peaks around 600 cm{sup -1} which are typical for cubic spinel crystal structure. SEM study revealed compact flakes like morphology having thickness {approx}1.8 {mu}m after air annealing. The annealed films were super hydrophilic in nature having a static water contact angle ({theta}) of 5{sup o}.The electrochemical supercapacitor study of Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films has been carried out in 6 M KOH electrolyte. The values of interfacial and specific capacitances obtained were 0.0285 F cm{sup -2} and 19 F g{sup -1}, respectively.

Fabrication and Electrochemical Performance of LiNi0.5Co0.2Mn0.3O2 Coated with Nano FePO4 as Cathode Material for Lithium-ion Batteries

Directory of Open Access Journals (Sweden)

DONG Peng

2017-11-01

Full Text Available Layered LiNi0.5Co0.2Mn0.3O2 coated with homogeneous nano FePO4 suspension was prepared by using co-precipitation method. XRD, TG-DTA and TEM were adopted to characterize the structure, morphology and liquid state of FePO4 prepared. The structure, morphology and electrochemical performance of the coated materials prepared were characterized by the means such as XRD, SEM, EDS, TEM, ICP, galvanostatic charge-discharge cycling, cyclic voltammetry (CV and electrochemical impedance spectroscopy(EIS tests. The effect of heat treatment temperature and coating quantity on the structure and electrochemical performance of coated LiNi0.5Co0.2Mn0.3O2 by co-precipitation method was explored. The results show that 400℃ and 2%(mass fraction,the same below FePO4 coating can significantly improve cycle performance and rate capability of LiNi0.5Co0.2Mn0.3O2, CV and EIS testing results reveal that FePO4 coating can improve the reversibility and dynamic performance for LiNi0.5Co0.2Mn0.3O2. ICP results show that FePO4 coating layer can effectively reduce the electrolyte to dissolute and erode cathode materials, stabilize its layered structure, then improve the electrochemical performance of cathode materials.

Enhancement of the Si p-n diode NIR photoresponse by embedding β-FeSi2 nanocrystallites.

Science.gov (United States)

Shevlyagin, A V; Goroshko, D L; Chusovitin, E A; Galkin, K N; Galkin, N G; Gutakovskii, A K

2015-10-05

By using solid phase epitaxy of thin Fe films and molecular beam epitaxy of Si, a p(+)-Si/p-Si/β-FeSi2 nanocrystallites/n-Si(111) diode structure was fabricated. Transmission electron microscopy data confirmed a well-defined multilayered structure with embedded nanocrystallites of two typical sizes: 3-4 and 15-20 nm, and almost coherent epitaxy of the nanocrystallites with the Si matrix. The diode at zero bias conditions exhibited a current responsivity of 1.7 mA/W, an external quantum efficiency of about 0.2%, and a specific detectivity of 1.2 × 10(9) cm × Hz(1/2)/W at a wavelength of 1300 nm at room temperature. In the avalanche mode, the responsivity reached up to 20 mA/W (2% in terms of efficiency) with a value of avalanche gain equal to 5. The data obtained indicate that embedding of β-FeSi2 nanocrystallites into the depletion region of the Si p-n junction results in expansion of the spectral sensitivity up to 1600 nm and an increase of the photoresponse by more than two orders of magnitude in comparison with a conventional Si p-n junction. Thereby, fabricated structure combines advantage of the silicon photodiode functionality and simplicity with near infrared light detection capability of β-FeSi2.

Analysis of standard problem six (Semiscale test S-02-6) data

International Nuclear Information System (INIS)

Cartmill, C.E.

1977-08-01

Test S-02-6 of the Semiscale Mod-1 blowdown heat transfer test series was conducted to supply data for the U.S. Nuclear Regulatory Commission Standard Problem Six. To determine the credibility of the data and thus establish the validity of Standard Problem Six, an analysis of the results of Test S-02-6 was performed and is presented. This analysis consisted of investigations of system hydraulic and core thermal data. The credibility of the system hydraulic data was investigated through comparisons of the data with data and calculations from related sources (Test S-02-4) and, when necessary, through assessment of physical events. The credibility of the core thermal data was based on a thorough analysis of physical events. The results of these investigations substantiate the validity of Test S-02-6 data

Metal-organic framework derived Fe/Fe3C@N-doped-carbon porous hierarchical polyhedrons as bifunctional electrocatalysts for hydrogen evolution and oxygen-reduction reactions.

Science.gov (United States)

Song, Chunsen; Wu, Shikui; Shen, Xiaoping; Miao, Xuli; Ji, Zhenyuan; Yuan, Aihua; Xu, Keqiang; Liu, Miaomiao; Xie, Xulan; Kong, Lirong; Zhu, Guoxing; Ali Shah, Sayyar

2018-08-15

The development of simple and cost-effective synthesis methods for electrocatalysts of hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR) is critical to renewable energy technologies. Herein, we report an interesting bifunctional HER and ORR electrocatalyst of Fe/Fe 3 C@N-doped-carbon porous hierarchical polyhedrons (Fe/Fe 3 C@N-C) by a simple metal-organic framework precursor route. The Fe/Fe 3 C@N-C polyhedrons consisting of Fe and Fe 3 C nanocrystals enveloped by N-doped carbon shells and accompanying with some carbon nanotubes on the surface were prepared by thermal annealing of Zn 3 [Fe(CN) 6 ] 2 ·xH 2 O polyhedral particles in nitrogen atmosphere. This material exhibits a large specific surface area of 182.5 m 2  g -1 and excellent ferromagnetic property. Electrochemical tests indicate that the Fe/Fe 3 C@N-C hybrid has apparent HER activity with a relatively low overpotential of 236 mV at the current density of 10 mA cm -2 and a small Tafel slope of 59.6 mV decade -1 . Meanwhile, this material exhibits excellent catalytic activity toward ORR with an onset potential (0.936 V vs. RHE) and half-wave potential (0.804 V vs. RHE) in 0.1 M KOH, which is comparable to commercial 20 wt% Pt/C (0.975 V and 0.820 V), and shows even better stability than the Pt/C. This work provides a new insight to developing multi-functional materials for renewable energy application. Copyright © 2018 Elsevier Inc. All rights reserved.

Moessbauer Spectroscopy Studies of Some Intermetallics in the Zr-Nb-Fe System

International Nuclear Information System (INIS)

Ramos, C.; Saragovi, C.; Granovsky, M.; Arias, D.

2002-01-01

Samples with the following compositions: Zr 62 Nb 14 Fe 24 , Zr 65 Nb 10 Fe 25 and Zr 52 Nb 10 Fe 38 were studied by Moessbauer spectroscopy. All of them showed a ternary cubic Ti 2 Ni-type phase (QS: 0.30±0.02, IS: -0.14±0.01) and traces of Zr 2 Fe phase (QS: 0.86±0.03, IS: -0.29±0.01). Zrβ phase (QS: 0.22±0.01, IS: -0.11±0.01) was also detected except in the case of the richer Fe sample. In addition to these expected phases, a hexagonal MgZn 2 -type phase was determined. The assigned parameters for this phase are: QS: 0.38±0.04, IS: -0.28±0.02. These results suggest a revision of the diagram.

(SiC/AlN)2 multilayer film as an effective protective coating for sintered NdFeB by magnetron sputtering

Science.gov (United States)

You, Yu; Li, Heqin; Huang, Yiqin; Tang, Qiong; Zhang, Jing; Xu, Jun

2017-08-01

SiC/AlN and (SiC/AlN)2 multilayer films with a well-arranged bilayer structure and a four-layer structure are prepared respectively on NdFeB substrates by a magnetron sputtering method. Crystal phase and microstructures of the SiC/AlN and (SiC/AlN)2 films are investigated using x-ray diffraction (XRD), field-emission scanning electron microscope (FESEM) and atomic force microscope (AFM). It is observed that the surface of the (SiC/AlN)2 four-layer film is much denser and smoother than that of the SiC/AlN bilayer film. Corrosion behaviors of the NdFeB substrates coated with SiC/AlN and (SiC/AlN)2 films as well as the bare NdFeB substrate are evaluated by potentiodynamic polarization curve tests. It is revealed that the lateral growth structures developed in interfaces are favorable for an enhanced corrosion resistance. Corrosion current densities of the (SiC/AlN)2 coated NdFeB measured in acid, alkali and salt solutions are 2.796  ×  10-9, 3.65  ×  10-6, and 2.912  ×  10-6 A cm-2, respectively, which are much lower than those of the bare NdFeB and the SiC/AlN coated NdFeB.

A-Site Deficient (Pr0.6Sr0.4)(1-s)Fe0.8Co0.2O3-delta Perovskites as Solid Oxide Fuel Cell Cathodes

DEFF Research Database (Denmark)

Kammer Hansen, Kent

2009-01-01

Five A-site deficient (Pr0.6Sr0.4)1−sFe0.8Co0.2O3− perovskites (s=0.01, 0.05, 0.10, 0.15, and 0.20) were synthesized using the glycine-nitrate process. The perovskites were characterized with powder X-ray diffraction (XRD), dilatometry, four-point dc conductivity measurements, and electrochemical...... resistance more than 3 times lower than the weakly A-site deficient (Pr0.6Sr0.4)0.99Fe0.8Co0.2O3− perovskite. ©2009 The Electrochemical Society...

Raman Scattering in La0.2Sr0.8FeO3-δ thin film: annealing-induced reduction and phase transformation

Science.gov (United States)

Islam, Mohammad; Xie, Yujun; Scafetta, Mark; May, Steven; Spanier, Jonathan

2015-03-01

Raman scattering in thin film La0.2Sr0.8FeO3-δ on MgO(001) collected at 300 K following different stages of annealing at selected temperatures (300 K topotactic transformation of the crystal structure from that of the rhombohedral ABO3 perovskites to that of Brownmillerite-like structure consisting of octahedrally and tetrahedrally coordinated Fe atoms. We acknowledge the ONR (N00014-11-1-0664), the Drexel Centralized Research Facilities, the Army Research Office DURIP program, the Department of Education (GAANN-RETAIN, Award No. P200A100117), and Leszek Wielunski at Rutgers University.

Indirect flow injection determination of N-acetyl-L-cysteine using cerium(IV) and ferroin

International Nuclear Information System (INIS)

Vieira, Heberth Juliano; Fatibello-Filho, Orlando

2005-01-01

An indirect flow injection spectrophotometric procedure is proposed for the determination of N-acetyl-L-cysteine in pharmaceutical formulations. In this system, ferroin ([Fe(II)-(fen) 2 ] 2+ ) in excess, with a strong absorption at 500 nm, is oxidized by cerium(IV) yielding cerium(III) and [Fe(III)-(fen) 2 ] 3+ (colorless), thus producing a baseline. When N-acetyl-L-cysteine solution is introduced into the flow injection system, it reacts with cerium(IV) increasing the analytical signal in proportion to the drug concentration. Under optimal experimental conditions, the linearity of the analytical curve for N-acetyl-L-cysteine ranged from 6.5x10 -6 to 1.3x10 -4 mol L -1 . The detection limit was 5.0x10 -6 mol L -1 and recoveries between 98.0 and 106% were obtained. The sampling frequency was 60 determinations per hour and the RSD was smaller than 1.4% for 2.2x10 -5 mol L -1 N-acetyl-L-cysteine. (author)

Synthesis and characterization of Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles as a magnetic drug delivery system

Science.gov (United States)

Ansari, Mohammad; Bigham, Ashkan; Hassanzadeh-Tabrizi, S. A.; Abbastabar Ahangar, H.

2017-10-01

Mixed spinel ferrite nanoparticles are being applied in biomedical applications due to their biocompatibility, antibacterial activity, particular magnetic and electronic properties with chemical and thermal stabilities. The Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles are synthesized through the thermal treatment method. Polyvinyl alcohol (PVA) is used as the capping agent to stabilize the particles and prevent their agglomeration. The synthesized nanoparticles are characterized through X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FTIR), N2 adsorption-desorption, field emission scanning electron microscopy (FESEM), and transmission electron microscope (TEM). The magnetic characterization is made on a vibrating sample magnetometer (VSM), which displayed super-paramagnetic behavior of the synthesized sample. Potential application of the Cu0.3Zn0.5Mg0.2Fe2O4 nanoparticles as a drug delivery agent is assessed in vitro by estimating their release properties. The obtained results indicate that the amount of ibuprofen (IBU) adsorbed into the nanocarrier of Cu0.3Zn0.5Mg0.2Fe2O4 is 104 mg/g and the drug release is sustained up to 72 h.

The influence of Fe doping on the surface topography of GaN epitaxial material

International Nuclear Information System (INIS)

Cui Lei; Yin Haibo; Jiang Lijuan; Wang Quan; Feng Chun; Xiao Hongling; Wang Cuimei; Wang Xiaoliang; Gong Jiamin; Zhang Bo; Li Baiquan; Wang Zhanguo

2015-01-01

Fe doping is an effective method to obtain high resistivity GaN epitaxial material. But in some cases, Fe doping could result in serious deterioration of the GaN material surface topography, which will affect the electrical properties of two dimensional electron gas (2DEG) in HEMT device. In this paper, the influence of Fe doping on the surface topography of GaN epitaxial material is studied. The results of experiments indicate that the surface topography of Fe-doped GaN epitaxial material can be effectively improved and the resistivity could be increased after increasing the growth rate of GaN materials. The GaN material with good surface topography can be manufactured when the Fe doping concentration is 9 × 10 19 cm −3 . High resistivity GaN epitaxial material which is 1 × 10 9 Ω·cm is achieved. (paper)

Cobalt–iron red–ox behavior in nanostructured La0.4Sr0.6Co0.8Fe0.2O3−δ cathodes

DEFF Research Database (Denmark)

Soldati, Analía L.; Baqué, Laura; Napolitano, Federico

2013-01-01

Nano-sized La0.4Sr0.6Co0.8Fe0.2O3−δ (LSCF) perovskite samples (prepared by a conventional acetate route and a novel acetate synthesis with HMTA additives), were tested simulating a red–ox cycle. The crystallography was studied by X-ray Powder Diffraction (XPD) and the changes in the oxidation state...... of the perovskite B-site were evaluated by synchrotron X-ray Absorption Near Edge Spectroscopy (XANES). After a reducing treatment, LSFC particles show the appearance of a new phase that coexists with the original one. The structural change is accompanied by a Co and Fe formal oxidation states decrease, although Fe...... remains always closer to 4+ and Co closer to 3+. The treatment produces a B-site valence average reduction from 3.52+ to 3.26+ and the formation of oxygen vacancies. A re-oxidation treatment under O2 rich atmosphere at 800°C for 10h shows that the change is reversible and independent of the two chemical...

Validation and Verification (V and V) Testing on Midscale Flame Resistant (FR) Test Method

Science.gov (United States)

2016-12-16

materials . The results demonstrated that the Midscale test is a quick and cost-effective method for evaluation of FR performance of design features...standard and novel FR materials and design configurations during fire engulfment. Details of the test method and its development can be found in the...employed in the FRACU is a ripstop fabric blend of 65% FR rayon, 25% para- aramid and 10% nylon. The iCVC material is Nylon/Cotton/Nomex. All three

Moessbauer Spectroscopy Studies of Some Intermetallics in the Zr-Nb-Fe System

Energy Technology Data Exchange (ETDEWEB)

Ramos, C. [CNEA-UNSAM, Comision Nacional de Energia Atomica, Instituto de Tecnologia J. Sabato (Argentina); Saragovi, C. [Comision Nacional de Energia Atomica, Departamento de Fisica (Argentina); Granovsky, M.; Arias, D. [Comision Nacional de Energia Atomica, Departamento de Materiales (Argentina)

2002-03-15

Samples with the following compositions: Zr{sub 62}Nb{sub 14}Fe{sub 24}, Zr{sub 65}Nb{sub 10}Fe{sub 25} and Zr{sub 52}Nb{sub 10}Fe{sub 38} were studied by Moessbauer spectroscopy. All of them showed a ternary cubic Ti{sub 2}Ni-type phase (QS: 0.30{+-}0.02, IS: -0.14{+-}0.01) and traces of Zr{sub 2}Fe phase (QS: 0.86{+-}0.03, IS: -0.29{+-}0.01). Zr{beta} phase (QS: 0.22{+-}0.01, IS: -0.11{+-}0.01) was also detected except in the case of the richer Fe sample. In addition to these expected phases, a hexagonal MgZn{sub 2}-type phase was determined. The assigned parameters for this phase are: QS: 0.38{+-}0.04, IS: -0.28{+-}0.02. These results suggest a revision of the diagram.

Automatic chemical determination facility for plutonium and uranium

International Nuclear Information System (INIS)

Benhamou, A.

1980-01-01

A proposal for a fully automated chemical determination system for uranium and plutonium in (U, Pu)O 2 mixed oxide fuel, from the solid sample weighing operation to the final result is described. The steps completed to data are described. These include: test sample preparation by weighing, potentiometer titration system, cleaning and drying of glassware after titration. The process uses a Mettler SR 10 Titrator System in conjunction with others automatized equipment in corse of realization. Precision may reach 0.02% and is generally better than 0.1%. Accuracy in within +-0.1% of manual determination results or titration standards [fr

In situ X-ray and neutron diffraction of the Ruddlesden-Popper compounds (RE2-xSrx)0.98(Fe0.8Co0.2)1-yMgyO4-δ (RE=La, Pr): Structure and CO2 stability

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Hauback, B.C.; Hendriksen, Peter Vang

2013-01-01

The crystal structure of the Ruddlesden-Popper compounds (La 1.0Sr1.0)0.98Fe0.8Co 0.2O4-δ and (La1.2Sr0.8) 0.98(Fe0.8Co0.2)0.8Mg 0.2O4-δ was investigated at 1000 °C in N 2 (aO2=1×10-4) by in-situ powder neutron diffraction. In-situ powder X-ray diffraction (PXD) was also employed to investigate....... The equivalent pseudo-cubic thermal and chemical expansion coefficients are in agreement with values determined by dilatometry. The chemical stability in CO2 containing environments of various Ruddlesden-Popper compounds with chemical formula (RE2-xSr x)0.98(Fe0.8Co0.2) 1-yMgyO4-δ (RE=La, Pr), as well...

Effect of hydrogen on Ti-10V-2Fe-3Al

International Nuclear Information System (INIS)

Costa, J.E.

1985-01-01

The effect of hydrogen on the physical and mechanical properties of the metastable β alloy Ti-10V-2Fe-3Al was examined. This study had three main goals. The first was to improve the understanding of the effects of hydrogen in the β phase. The second goal was to determine the effects of hydrogen on the specific alloy Ti-10V-2Fe-3Al. The third goal was to identify possible in-service problems that could occur in Ti-10V-2Fe-3Al and in similar alloys. The effects of hydrogen were examined in three different microstructures: beta-annealed and water-quenched (B/WQ), beta-annealed and furnace cooled (B/FC), and solution treated and aged (STA). The B/WQ microstructure was nominally all-β with some athermal omega phase while the B/FC and STA microstructures were α + β microstructures. Hydrogen concentrations from approx.0 to >30 at.% were used. Hydrogen was introduced into test specimens using either Sieverts charging or cathodic charging techniques. When the B/WQ microstructure was deformed, the β phase was transformed to orthorhombic α'' martensite. Hydrogen effects in the B/FC and STA microstructures were largely the result of hydride formation at α/β interfaces. The effect of hydride formation was observed as decreases in the reduction of area for tensile specimens

Austenitic alloys Fe-Ni-Cr dominating

International Nuclear Information System (INIS)

Gibson, R.C.; Korenko, M.K.

1980-01-01

Austenitic alloy essentially comprising 42 to 48% nickel, 11 to 13% chromium, 2.6 to 3.4% niobium, 0.2 to 1.2% silicon, 0.5 to 1.5% vanadium, 2.6 to 3.4% molybdenum, 0.1 to 0.3% aluminium, 0.1 to 0.3% titanium, 0.02 to 0.05% carbon, 0.002 to 0.015% boron, up to 0.06% zirconium, the balance being iron. The characteristic of this alloy is a conventional elasticity limit to within 2% of at least 450 MPa, with a maximum tensile strength of at least 500 MPa at a test temperature of 650 0 C after immersion annealing at 1038 0 C and 30% hardening. To this effect the invention concerns Ni-Cr-Fe high temperature alloys possessing excellent mechanical strength characteristics, that can be obtained with lower levels of nickel and chromium than those used in alloys of this kind in the present state of the technique, a higher amount of niobium than in the previous alloys and with the addition of 0.5 to 1.5% vanadium [fr

La fracción evaporativa en diferentes regiones agrícolas y naturales del centro-noroeste de la Argentina

Directory of Open Access Journals (Sweden)

E.S Luna Toledo

2013-06-01

Full Text Available La fracción evaporativa (FE permite cuantificar la porción de la energía disponible usada en el proceso de evapotranspiración. Se obtuvo la distribución espacial de la FE para cinco tipos de cobertura: árboles, cultivos, pastizales, arbustos y suelo desnudo de cinco ecorregiones del centro-noroeste de la Argentina, usando productos del sensor MODIS-TERRA. FE se calculó mediante el método triangular según la relación entre la fracción de la cobertura de suelo (Fr y la temperatura de superficie (Ts. Ambas variables fueron correlacionadas para cada tipo de cobertura por ecorregión. Fr y Ts están inversamente asociadas, y diferentes coberturas por ecorregiones mostraron cambios en la pendiente de la recta entre ambas variables debido a cambios en el porcentaje y el tipo de cobertura, en los gradientes pluviométricos y en la estructura de la vegetación. Los valores medios de Fr y FE por ecorregiones y tipo de cobertura fueron procesados mediante el análisis de la varianza y por comparaciones múltiples de Fisher. Existen diferencias estadísticas significativas en las variables Fr y FE según el tipo de cobertura, y la ecorregión y la relación entre Fr y FE no es lineal. Finalmente, se generó un mapa con la distribución espacial de la FE.

Effects of exposure to 56Fe particles of protons on fixed-ratio operant responding in rats

International Nuclear Information System (INIS)

Rabin, B.M.; Buhler, L.L.; Jenkins, D.G.; Joseph, J.A.; Shukitt-Hale, B.

2002-01-01

On long-duration trips outside of the magnetosphere, astronauts will be exposed to protons and to heavy particles which can affect their performance of required tasks. It is essential to determine the range of behaviors that might be affected by exposure to these types of radiation in order to understand the nature of behavioral deficits and to develop effective countermeasures. The present experiment examined the ability of rats to make an operant response following exposure to protons (250 MeV, 4 Gy) or 56 Fe particles (1 GeV/n, 1 or 2 Gy). Following irradiation, rats were trained to press a lever in order to obtain food reinforcement. They were then placed on an ascending fixed-ratio schedule from FR-1 (each lever press rewarded with a food pellet) through FR-35 (35 lever presses required for 1 food pellet). Rats exposed to 4 Gy of protons or 1 Gy of 56 Fe particles responded similarly to controls, increasing their rate of responding as the ratio increased. However, rats exposed to 2 Gy of 56 Fe particles failed to increase their rate of responding at ratios greater than FR-20, indicating that rats exposed to 2 Gy of 56 Fe particles cannot respond appropriately to increasing work requirements. (author)

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

International Nuclear Information System (INIS)

Luo, Liqiang; Zhang, Yuting; Li, Fang; Si, Xiaojing; Ding, Yaping; Deng, Dongmei; Wang, Tianlin

2013-01-01

Graphical abstract: -- Highlights: •Spinel-type Co x Ni 1−x Fe 2 O 4 (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) were synthesized. •Co x Ni 1−x Fe 2 O 4 were first employed as novel enzyme mimic sensing materials of H 2 O 2 . •Co 0.5 Ni 0.5 Fe 2 O 4 /CPE showed excellent electrocatalytic activity to H 2 O 2 . •Co 0.5 Ni 0.5 Fe 2 O 4 /CPE was successfully applied to determine H 2 O 2 in toothpastes. -- Abstract: A series of spinel-type Co x Ni 1−x Fe 2 O 4 (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H 2 O 2 . X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co x Ni 1−x Fe 2 O 4 with different (Co/Ni) molar ratio toward H 2 O 2 oxidation were investigated, and the results demonstrated that Co 0.5 Ni 0.5 Fe 2 O 4 modified carbon paste electrode (Co 0.5 Ni 0.5 Fe 2 O 4 /CPE) possessed the best electrocatalytic activity for H 2 O 2 oxidation. Under optimum conditions, the calibration curve for H 2 O 2 determination on Co 0.5 Ni 0.5 Fe 2 O 4 /CPE was linear in a wide range of 1.0 × 10 −8 –1.0 × 10 −3 M with low detection limit of 3.0 × 10 −9 M (S/N = 3). The proposed Co 0.5 Ni 0.5 Fe 2 O 4 /CPE was also applied to the determination of H 2 O 2 in commercial toothpastes with satisfactory results, indicating that Co x Ni 1−x Fe 2 O 4 is a promising hydrogen peroxidase mimics for the detection of H 2 O 2

Microstructure and magnetic properties of nanostructured (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} alloy produced by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Boukherroub, N. [UR-MPE, M' hamed Bougara University, Boumerdes 35000 (Algeria); Guittoum, A., E-mail: aguittoum@gmail.com [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Laggoun, A. [UR-MPE, M' hamed Bougara University, Boumerdes 35000 (Algeria); Hemmous, M. [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Martínez-Blanco, D. [SCTs, University of Oviedo, EPM, 33600 Mieres (Spain); Blanco, J.A. [Department of Physics, University of Oviedo, Calvo Sotelo St., 33007 Oviedo (Spain); Souami, N. [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Gorria, P. [Department of Physics and IUTA, EPI, University of Oviedo, 33203 Gijón (Spain); Bourzami, A. [Laboratoire d' Etudes des Surfaces et Interfaces des Matériaux Solides (LESIMS), Université Sétif1, 19000 Sétif (Algeria); Lenoble, O. [Institut Jean Lamour, CNRS-Université de Lorraine, Boulevard des aiguillettes, BP 70239, F-54506 Vandoeuvre lès Nancy (France)

2015-07-01

We report on how the microstructure and the silicon content of nanocrystalline ternary (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} powders (x=0, 5, 10, 15 and 20 at%) elaborated by high energy ball milling affect the magnetic properties of these alloys. The formation of a single-phase alloy with body centred cubic (bcc) crystal structure is completed after 72 h of milling time for all the compositions. This bcc phase is in fact a disordered Fe(Al,Si) solid solution with a lattice parameter that reduces its value almost linearly as the Si content is increased, from about 2.9 Å in the binary Fe{sub 80}Al{sub 20} alloy to 2.85 Å in the powder with x=20. The average nanocrystalline grain size also decreases linearly down to 10 nm for x=20, being roughly half of the value for the binary alloy, while the microstrain is somewhat enlarged. Mössbauer spectra show a sextet thus suggesting that the disordered Fe(Al,Si) solid solution is ferromagnetic at room temperature. However, the average hyperfine field diminishes from 27 T (x=0) to 16 T (x=20), and a paramagnetic doublet is observed for the powders with higher Si content. These results together with the evolution of both the saturation magnetization and the coercive field are discussed in terms of intrinsic and extrinsic properties. - Highlights: • Single-phase nanocrystalline (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} (x=0, 5, 10, 15 and 20 at%) powders were successfully fabricated by mechanical alloying for a milling time of 72 h. • The insertion of Si atoms leads to a unit-cell contraction and a decrease in the average crystallite size. • The hyperfine and magnetic properties of (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} were influenced by the Si content.

Photo-Hall-effect study of excitation and recombination in Fe-doped GaN

Science.gov (United States)

Look, David C.; Leach, Jacob H.; Metzger, Robert

2017-02-01

The photo-Hall-effect was applied to the study of electron dynamics in semi-insulating Fe-doped GaN. High-powered light-emitting diodes of wavelengths λ = 940, 536, 449, 402, and 365 nm were used to excite steady-state free-electron volume concentrations Δn = 105-108 cm-3, depending on λ and intensity I0. Electron lifetime τ was determined from the energy E dependence of the excited sheet electron concentration Δns through the relationship Δns = I0τA(E), where the absorbance A(E) is a known function of sample thickness d and absorption coefficient α, and the energy dependence of α is taken from a theory of deep-center photoionization. The major sample impurities were Fe, Si, and C, with [Fe] ≫ [Si] and [C]. Fitted lifetimes τ ranged from 15 to 170 ps, depending on [Fe]. It was found that Δns ∝ I0 for [Si] > [C] and ∝ I01/2 for [Si] [C], some of the neutral Fe3+ is converted to Fe2+ with ground state Fe2+(5E) and excited state Fe2+(5T2); a fit of n vs. temperature T over the range of 290-325 K in the dark establishes E5E with respect to the conduction band: ECB - E5E = 0.564 eV - β5ET, where β5E = 3.6 × 10-4 eV/K. At room temperature, 294 K, ECB - E5E = 0.46 eV and ECB - E5T2 = 0.07 eV.

Formation cross section of iron-60 with reactor neutrons in 59Fe(n, γ)60Fe reaction

International Nuclear Information System (INIS)

Sato, T.; Suzuki, T.

1993-01-01

Ingrowth of 60 Co radioactivity in an iron sample irradiated in a nuclear reactor has been measured for determination of formation cross section of 60 Fe in the 59 Fe(n, γ) 60 Fe reaction with reactor neutrons. After 5 years cooling, the irradiated iron was purified from 60 Co and other radioactive nuclides by an anion exchange separation method and isopropyl ether extraction in hydrochloric acid. The amount of 60 Co ingrowth was measured by γ-spectrometry using a Ge-detector coupled to a multichannel pulse height analyzer 4 years after the purification of iron. Neutron flux of the irradiation position was calculated from the amount of 55 Fe produced. The observed value of 12.5 ± 2.8 barn is slightly greater than reported value for burnup cross section of 59 Fe(n, x)X, where x refers γ, α, d, p and 2n, and X is any nuclide produced by the above reactions. (author) 8 refs.; 2 tabs

Study of magnetic behavior in hexagonal-YMn{sub 1−x}Fe{sub x}O{sub 3} (x=0 and 0.2) nanoparticles using remanent magnetization curves

Energy Technology Data Exchange (ETDEWEB)

Chauhan, Samta; Singh, Amit Kumar; Srivastava, Saurabh Kumar; Chandra, Ramesh, E-mail: ramesfic@iitr.ac.in

2016-09-15

We have studied the magnetic behavior of YMn{sub 1−x}Fe{sub x}O{sub 3} (x=0 and 0.2) nanoparticles synthesized by conventional solid state reaction method. The as-synthesized nanoparticles were found to have hexagonal phase with P6{sub 3cm} space group confirmed by X-Ray diffraction. The particle size was found to be ~70 nm as confirmed by both X-Ray diffraction and Transmission Electron Microscopy. DC magnetization and memory effect measurements imply that the h-YMnO{sub 3} nanoparticles bear a resemblance to super spin-glass state following de Almeida–Thouless like behavior which is being suppressed by Fe-doping. The Fe-doping in YMnO{sub 3} enhances the antiferromagnetic (AFM) transition temperature T{sub N} to ~79 K and induces a new magnetic state due to the surface spins which is realized as diluted antiferromagnet in a field (DAFF) as explored by the thermoremanent and isothermoremanent magnetization measured with different applied magnetic field. - Highlights: • Magnetic behavior of h-YMn{sub 1−x}Fe{sub x}O{sub 3} (x=0 and 0.2) nanoparticles have been studied. • The nanoparticles (~70 nm) were synthesized by solid state reaction method. • Magnetic data reveal spin-glass behavior in YMnO{sub 3} which was suppressed in YMn{sub 0.8}Fe{sub 0.2}O{sub 3}. • The h-YMnO{sub 3} nanoparticles show memory effect and obey de-Almeida Thouless line. • TRM and IRM suggest spin glass nature for YMnO{sub 3}, while the YMn{sub 0.8}Fe{sub 0.2}O{sub 3} resembles DAFF.

Anisotropic thermal expansion of La(n)(Ti,Fe)(n)O(3n + 2) (n = 5 and 6).

Science.gov (United States)

Wölfel, Alexander; Dorscht, Philipp; Lichtenberg, Frank; van Smaalen, Sander

2013-04-01

Crystal structures are reported for two perovskite-related compounds with nominal compositions La5(Ti(0.8)Fe(0.2))5O17 and La6(Ti(0.67)Fe(0.33))6O20 at seven different temperatures between 90 and 350 K. For both compounds no evidence of a structural phase transition in the investigated range of temperatures was found. The thermal expansions are found to be anisotropic, with the largest thermal expansion along a direction parallel to the slabs of these layered compounds. The origin of this anisotropy is proposed to be a temperature dependence of tilts of the octahedral (Ti,Fe)O6 groups. It is likely that the same mechanism will determine similar anisotropic thermal behaviour of other compounds A(n)B(n)O(3n + 2). The crystal structures have revealed partial chemical order of Ti/Fe over the B sites, with iron concentrated towards the centers of the slabs. Local charge compensation is proposed as the driving force for the chemical order, where the highest-valent cation moves to sites near the oxygen-rich borders of the slabs. A linear dependence on the site occupation fraction by Fe of the computed valences leads to extrapolated valence values close to the formal valence of Ti(4+) for sites fully occupied by Ti, and of Fe(3+) for sites fully occupied by Fe. These results demonstrate the power of the bond-valence method, and they show that refined oxygen positions are the weighted average of oxygen positions in TiO6 and FeO6 octahedral groups.

Single peak parameters technique for simultaneous measurements: Spectrophotometric sequential injection determination of Fe(II) and Fe(III).

Science.gov (United States)

Kozak, J; Paluch, J; Węgrzecka, A; Kozak, M; Wieczorek, M; Kochana, J; Kościelniak, P

2016-02-01

Spectrophotometric sequential injection system (SI) is proposed to automate the method of simultaneous determination of Fe(II) and Fe(III) on the basis of parameters of a single peak. In the developed SI system, sample and mixture of reagents (1,10-phenanthroline and sulfosalicylic acid) are introduced into a vessel, where in an acid environment (pH≅3) appropriate compounds of Fe(II) and Fe(III) with 1,10-phenanthroline and sulfosalicylic acid are formed, respectively. Then, in turn, air, sample, EDTA and sample again, are introduced into a holding coil. After the flow reversal, a segment of air is removed from the system by an additional valve and as EDTA replaces sulfosalicylic acid forming a more stable colorless compound with Fe(III), a complex signal is registered. Measurements are performed at wavelength 530 nm. The absorbance measured at minimum of the negative peak and the area or the absorbance measured at maximum of the signal can be used as measures corresponding to Fe(II) and Fe(III) concentrations, respectively. The time of the peak registration is about 2 min. Two-component calibration has been applied to analysis. Fe(II) and Fe(III) can be determined within the concentration ranges of 0.04-4.00 and 0.1-5.00 mg L(-1), with precision less than 2.8% and 1.7% (RSD), respectively and accuracy better than 7% (RE). The detection limit is 0.04 and 0.09 mg L(-1) for Fe(II) and Fe(III), respectively. The method was applied to analysis of artesian water samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Calibration and energy response of the Bitt RM10/RS02 gamma radiation detectors

International Nuclear Information System (INIS)

Dijk, E. van; Aalbers, A.H.L.

1990-03-01

A radiation monitoring network with automatic warning capabilities (LMR) has been established in the Netherlands. For the detection of gamma radiation exposure-rate-meters manufactured by Bitt Technologies are used. These meters consist of a proportional counter tube (type RS 02) and a read-out unit (type RM 10E). The photon energy response of 6 counter tubes was tested at the National Institute of Public Health and Environmental Protection. The measurements were performed with heavy filtered X-rays in the range of 50-250 keV (ISO narrow spectrum series) and with gamma ray beams from cesium-137 (662 keV) and cobalt-60 (1,25 MeV). To determine the energy response, the detector reading was referred to air kerma by means of a transfer ionization chamber. This transfer chamber was directly calibrated against the standard for X-rays. By applying these measurement procedures of a set of calibration factors (N k ) as a function of photon energy was determined. These calibration factors, expressed as the ratio air kerma to reading were converted to ambient dose equivalent calibration factors using appropriate conversion factors taken from Grosswend et al., 1988. From the measurement data an average ambient dose equivalent calibration factor of 10.8 mSv.roentgen -1 was calculated. (author). 5 refs.; 6 figs.; 5 tabs

Enhanced photocatalytic property of BiFeO_3/N-doped graphene composites and mechanism insight

International Nuclear Information System (INIS)

Li, Pai; Li, Lei; Xu, Maji; Chen, Qiang; He, Yunbin

2017-01-01

Highlights: • A hydrothermal process was used to prepare BiFeO_3/N-doped graphene composites. • BiFeO_3/N-doped graphene exhibits superior photocatalytic activity and stability. • The energy band of BiFeO_3 bends downward by ∼1.0 eV at the composite interface. • Downward band bending leads to rapid electron transfer at the composite interface. • Holes and ·OH are predominant active species in the photo-degradation process. - Abstract: A series of BiFeO_3/(N-doped) graphene composites are prepared by a facile hydrothermal method. BiFeO_3/N-doped graphene shows photocatalytic performance superior to that of BiFeO_3/graphene and pristine BiFeO_3. The enhanced photo-degradation performance of BiFeO_3/N-doped graphene are mainly attributable to the improved light absorbance of the composite, abundant active adsorption sites and high electrical charge mobility of N-doped graphene, and the downward band bending of BiFeO_3 at the composite interface. In particular, X-ray photoelectron spectroscopy analyses reveal that the electron energy band of BiFeO_3 is downward bent by 1.0 eV at the interface of BiFeO_3/N-doped graphene, because of different work functions of both materials. This downward band bending facilitates the transfer of photogenerated electrons from BiFeO_3 to N-doped graphene and prompts the separation of photo-generated electron-hole pairs, leading eventually to the enhanced photocatalytic performance.

Separation of Cu, In, Fe and Sn from nuclear grade thorium by tri-n-octyl amine-5 M HCI and their determination by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Moraes, S. de; Cipriani, M.; Abrao, A.

1976-01-01

The results of solvent extraction separation of a group of metal traces in high pure thorium with the aid of tri-n-octyl amine-benzene from ThCL 4 HCI are summarized. ThCl 4 HCI-KI solutions Cu,In,Fe and Sn are extracted together and determined by atomic absoprtion spectrophotometry, burning directly the organic phase. The behavior of Cu,In,Fe and Sn toward direct burn of the organic phase using hydrogen-air mixture was studied, and an absorption enhancement was observed. The procedure is being used ot perform the quality control of nuclear grade thorium and its compounds. The calibration curves have provided precisions in the range 1 to 10% in analysis of thorium

76 FR 18348 - Required Scale Tests

Science.gov (United States)

2011-04-04

... RIN 0580-AB10 Required Scale Tests AGENCY: Grain Inspection, Packers and Stockyards Administration... published a document in the Federal Register on January 20, 2011 (76 FR 3485), defining required scale tests... the last sentence of paragraph (a) to read as follows: Sec. 201.72 Scales; testing of. (a...

Corrosion Resistance of Steels and Armco-Fe in Lead Melt Saturated by Oxygen at 550 degree C

International Nuclear Information System (INIS)

Tsisar, V.P.; Fedirko, V.N.; Eliseeva, O.I.

2007-01-01

Corrosion resistance of stainless steels and Armco-Fe in static lead melt saturated by oxygen at 550 degree C for 2000 h was investigated. It was determined that double oxide layer was formed on the surface of investigated materials. Outer part of double oxide growths from the initial interface 'solid metal/liquid lead' towards the melt and consists of Fe 3 O 4 . Inner part of double oxide based on the matrix is composed of Fe 3 O 4 for Armco-Fe, Fe 1+x Cr 2-x O 4 for martensitic 0.2 C-13 Cr and ferritic-martensitic EP823 steels and Fe 1+x Cr 2- xO 4 +Ni for austenitic 18Cr-10Ni-1Ti. Lead did not penetrate into the matrix of tested materials and was detected only in the scale formed on austenitic steel

Micro-XANES Determination Fe Speciation in Natural Basalts at Mantle-Relevant fO2

Science.gov (United States)

Fischer, R.; Cottrell, E.; Lanzirotti, A.; Kelley, K. A.

2007-12-01

We demonstrate that the oxidation state of iron (Fe3+/ΣFe) can be determined with a precision of ±0.02 (10% relative) on natural basalt glasses at mantle-relevant fO2 using Fe K-edge X-ray absorption near edge structure (XANES) spectroscopy. This is equivalent to ±0.25 log unit resolution relative to the QFM buffer. Precise determination of the oxidation state over this narrow range (Fe3+/ΣFe=0.06-0.30) and at low fO2 (down to QFM-2) relies on appropriate standards, high spectral resolution, and highly reproducible methods for extracting the pre-edge centroid position. We equilibrated natural tholeiite powder in a CO/CO2 gas mixing furnace at 1350°C from QFM-3 to QFM+2 to create six glasses of known Fe3+/ΣFe, independently determined by Mössbauer spectroscopy. XANES spectra were collected at station X26A at NSLS, Brookhaven Natl. Lab, in fluorescence mode (9 element Ge array detector) using both Si(111) and Si(311) monochromators. Generally, the energy position of the 1s→3d (pre-edge) transition centroid is the most sensitive monitor of Fe oxidation state using XANES. For the mixture of Fe oxidation states in these glasses and the resulting coordination geometries, the pre-edge spectra are best defined by two multiple 3d crystal field transitions. The Si(311) monochromator, with higher energy resolution, substantially improved spectral resolution for the 1s→3d transition. Dwell times of 5s at 0.1eV intervals across the pre-edge region yielded spectra with the 1s→3d transition peaks clearly resolved. The pre-edge centroid position is highly sensitive to the background subtraction and peak fitting procedures. Differences in fitting models result in small but significant differences in the calculated peak area of each pre-edge multiplet, and the relative contribution of each peak to the calculated centroid. We assessed several schemes and obtained robust centroid positions by simultaneously fitting the background with a damped harmonic oscillator (DHO

Separation of zirconium through extraction in hydrochloric medium with tri-n-octilamine and its spectrophotometric determination with chloroanilic acid

International Nuclear Information System (INIS)

Floh, B.; Abrao, A.; Federgruen, L.

1976-01-01

A procedure is outlined for the spectrophotometric determination of zirconium using its complex with chloroanilic acid in HC10 4 2M. Interfering elements like Fe, Zn, U, Cy, Cd, Sb, Co, Pb, Hg, Tl, Pt, Au, Pd, Ga, In, Mo and W are previously extracted with tri-n-octylamine 7,5%-benzene from 4 M HCL. Then, the acid content of the solution is ascertained to 10 M HCL and zirconium is extracted with the amine. Nb is a strong interference, being extracted by the amine as well as zirconium and absorbing at the same region as zirconium chloroanilate. Zirconium is stripped from the organic phase with Na 2 CO 3 . The colour development is done with chloroanilic acid in 2 M HC10 4 and the measurements at 340 nm. The method allows the determination of 5 micrograms of Zr. The work curve covers the 0.2 - 2.0 μg Zr/mL range. The procedure is being applied to the determination of zirconium in several alloys and in samples containing zinc, magnesium, iron, aluminium, uranium and thorium [pt

(CaFeAs)10PtzAs8 superconductors and related compounds

International Nuclear Information System (INIS)

Stuerzer, Tobias

2015-01-01

The main topic of this dissertation is the identification of new compounds, structure determination, and substitution dependent investigation of properties in this new branch of the family of iron arsenide superconductors (Chapter 2). Chapter 2.1 presents the identification of the superconducting compounds and the corresponding structure elucidation identifying two dif-ferent species (CaFeAs) 10 Pt 3 As 8 and (CaFeAs) 10 Pt 4 As 8 in this family (abbreviated as 1038 and 1048 according to their stoichiometry). However, a closer look revealed a more challenging structure chemistry which is covered in Chapter 2.2. The following two Chapters 2.3 and 2.4 are devoted to (CaFeAs) 10 Pt 3 As 8 and more detailed investigations on this parent compound of the new superconductor family. Furthermore, transition metal substitution series (CaFe 1-x M x As) 10 Pt 3 As 8 were synthesized to investigate the resemblance to model systems Ba(Fe 1-x M x ) 2 As x and LaO(Fe 1-x M x )As in the scope of structural changes and superconductivity as described in Chapter 2.5. Initially amazing differences in superconducting properties com-paring 1038 and 1048 compounds are analyzed in Chapter 2.6 establishing an universal dop-ing model in the (CaFe 1-x M x As) 10 Pt z As 8 family. Additionally substituent dependent properties upon rare earth substitution in electron doped (Ca 1-y RE y FeAs) 10 Pt 3 As 8 are investigated in Chapter 2.7, while a detailed study of superconducting properties and magnetism in (Ca 1-y La y FeAs) 10 Pt 3 As 8 by the local μSR technique is presented in Chapter 2.8. In Chapter 2.9 a comparison of direct and electron doping is discussed based on codoping experiments in (Ca 1-y La y Fe 1-x Pt x As) 10 Pt 3 As 8 and (CaFe 1-x Pt x As) 10 Pt 4 As 8 . Finally, in Chapter 2.10 electron doping in stoichiometric 1048 is studied by charge compensation experiments in (Ca 1-y Na y FeAs) 10 Pt 4 As 8 . Chapter 3 is dedicated to a new family of calcium iron arsenides featuring

Feasibility of N2 Binding and Reduction to Ammonia on Fe-Deposited MoS2 2D Sheets: A DFT Study

KAUST Repository

Azofra Mesa, Luis

2017-05-19

Based on the structure of the nitrogenase FeMo cofactor (FeMoco), it is reported that Fe deposited on MoS2 2D sheets exhibits high selectivity towards the spontaneous fixation of N2 against chemisorption of CO2 and H2 O. DFT predictions also indicate the ability of this material to convert N2 into NH3 with a maximum energy input of 1.02 eV as an activation barrier for the first proton-electron pair transfer.

Feasibility of N2 Binding and Reduction to Ammonia on Fe-Deposited MoS2 2D Sheets: A DFT Study

KAUST Repository

Azofra Mesa, Luis; Sun, Chenghua; Cavallo, Luigi; MacFarlane, Douglas R.

2017-01-01

Based on the structure of the nitrogenase FeMo cofactor (FeMoco), it is reported that Fe deposited on MoS2 2D sheets exhibits high selectivity towards the spontaneous fixation of N2 against chemisorption of CO2 and H2 O. DFT predictions also indicate the ability of this material to convert N2 into NH3 with a maximum energy input of 1.02 eV as an activation barrier for the first proton-electron pair transfer.

Magnetoelectric effect in two-layered self-biased composites Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68}/epoxy - PbZr{sub 0.53}Ti{sub 0.47}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Kalgin, A.V.; Gridnev, S.A.; Popov, I.I. [Voronezh State Technical University, Voronezh (Russian Federation)

2017-03-15

Direct magnetoelectric (ME) effect in two-layered Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68}/Epoxy - PbZr{sub 0.53}Ti{sub 0.47}O{sub 3} composites containing magnetostrictive layers of the epoxy with distributed in it Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68} granules and piezoelectric layers of the PbZr{sub 0.53}Ti{sub 0.47}O{sub 3} ceramics was studied. It was found, that the gradient distribution of Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68} granules in magnetostrictive layers induces the internal (self-biased) magnetic field. This field leads to the increase in ME responses in composites with the gradient distribution of Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68} granules in magnetostrictive layers as compared with ME responses in composites with the random distribution of Tb{sub 0.12}Dy{sub 0.2}Fe{sub 0.68} granules in magnetostrictive layers, which does not induce the internal magnetic field. We revealed the possibility of controlling and determining values of the internal magnetic field in composites and conditions for obtaining optimal ME responses. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fe/N/C hollow nanospheres by Fe(iii)-dopamine complexation-assisted one-pot doping as nonprecious-metal electrocatalysts for oxygen reduction

Science.gov (United States)

Zhou, Dan; Yang, Liping; Yu, Linghui; Kong, Junhua; Yao, Xiayin; Liu, Wanshuang; Xu, Zhichuan; Lu, Xuehong

2015-01-01

In this work, a series of hollow carbon nanospheres simultaneously doped with N and Fe-containing species are prepared by Fe3+-mediated polymerization of dopamine on SiO2 nanospheres, carbonization and subsequent KOH etching of the SiO2 template. The electrochemical properties of the hollow nanospheres as nonprecious-metal electrocatalysts for oxygen reduction reaction (ORR) are characterized. The results show that the hollow nanospheres with mesoporous N-doped carbon shells of ~10 nm thickness and well-dispersed Fe3O4 nanoparticles prepared by annealing at 750 °C (Fe/N/C HNSs-750) exhibit remarkable ORR catalytic activity comparable to that of a commercial 20 wt% Pt/C catalyst, and high selectivity towards 4-electron reduction of O2 to H2O. Moreover, it displays better electrochemical durability and tolerance to methanol crossover effect in an alkaline medium than the Pt/C. The excellent catalytic performance of Fe/N/C HNSs-750 towards ORR can be ascribed to their high specific surface area, mesoporous morphology, homogeneous distribution of abundant active sites, high pyridinic nitrogen content, graphitic nitrogen and graphitic carbon, as well as the synergistic effect of nitrogen and iron species for catalyzing ORR.In this work, a series of hollow carbon nanospheres simultaneously doped with N and Fe-containing species are prepared by Fe3+-mediated polymerization of dopamine on SiO2 nanospheres, carbonization and subsequent KOH etching of the SiO2 template. The electrochemical properties of the hollow nanospheres as nonprecious-metal electrocatalysts for oxygen reduction reaction (ORR) are characterized. The results show that the hollow nanospheres with mesoporous N-doped carbon shells of ~10 nm thickness and well-dispersed Fe3O4 nanoparticles prepared by annealing at 750 °C (Fe/N/C HNSs-750) exhibit remarkable ORR catalytic activity comparable to that of a commercial 20 wt% Pt/C catalyst, and high selectivity towards 4-electron reduction of O2 to H2O

The origin of high magnetic properties in (R,Zr)(Fe,Co){sub 11.0–11.5}Ti{sub 1.0–0.5}N{sub y} (y=1.0–1.4 for R=Nd, y=0 for R=Sm) compounds

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, K., E-mail: koba@ms.sist.ac.jp [Shizuoka Institute of Science and Technology, 2200-2 Toyosawa, Fukuroi, Shizuoka 437-8555 (Japan); Suzuki, S.; Kuno, T.; Urushibata, K. [Shizuoka Institute of Science and Technology, 2200-2 Toyosawa, Fukuroi, Shizuoka 437-8555 (Japan); Sakuma, N.; Yano, M.; Shoji, T.; Kato, A. [Toyota Motor Corporation, 1200 Mishuku, Susono, Shizuoka 410-1193 (Japan); Technology Reserch Association of Magnetic Materials fot High-efficiency Motors (Mag-HEM) Higashifuji-Branch, 1200 Mishuku, Susono, Shizuoka 410-1193, Japan. (Japan); Manabe, A. [Technology Reserch Association of Magnetic Materials fot High-efficiency Motors (Mag-HEM) Higashifuji-Branch, 1200 Mishuku, Susono, Shizuoka 410-1193, Japan. (Japan)

2017-03-15

Ten alloys and nitrogenated compounds of (R,Zr)(Fe,Co){sub 11.0–11.5}Ti{sub 1.0–0.5}N{sub y} (y=1.0–1.4 for R=Nd, y=0 for R=Sm) with a ThMn{sub 12}-type structure were prepared. The average Fe–Fe interatomic distances, d(Fe–Fe), for Fe sites were calculated based on the reported atomic parameters. The hyperfine splittings (inner field (IF), in teslas) were measured by Mössbauer spectroscopy, and the IF increased with increasing d(Fe–Fe) for Fe sites, indicating a magneto-volume effect. The order of IF magnitude in Fe sites was Fe(8i)>Fe(8j)>Fe(8f) in all alloys. Co substitution for Fe sites, (Fe{sub 0.75}Co{sub 0.25}), increased the IF by 25% for the R=Nd alloy and 15% for the R=Sm alloy. Decreasing Ti content from −Ti{sub 1.0} to −Ti{sub 0.5}, which increased the Fe and Co content, preserved the ThMn{sub 12} structure with Zr substitution for R(2a) sites, and caused a slight increase in the IF of 2% for the R=Nd alloy and 7% for the R=Sm alloy. Nitrogenation, where N was introduced into the 2b sites, also increased IF in R=Nd alloys, by 23% for the Co- and Zr-free alloys, NdFe{sub 11}Ti{sub 1.0}N{sub 1.5}, and by 7% for the Co-containing, (Nd{sub 0.7}Zr{sub 0.3}) (Fe{sub 0.75}Co{sub 0.25}) {sub 11.5}Ti{sub 0.5}N{sub 1.3} alloy. The IF values of the R=Nd alloys were slightly larger than those of the R=Sm alloys. In conclusion, the magneto-volume effect was clearly observed at the Fe sites, and Co substitution into Fe sites and nitrogenation (R=Nd alloys) compensated for the increased IF. Increasing the Fe and Co fractions also increased IF slightly. - Highlights: • Average distances of Fe–Fe (d(Fe–Fe)) were calculated using lattice constants. • Hyperfine fields (IF) in Fe sites were measured using Mössbauer spectroscopy. • Relationship between d(Fe–Fe) and IF at each Fe site was obtained. • Co substitution and N introduction effects on IF was also measured. • Magneto-volume effect is main reason of IF augmentation in Fe sites.

Effects of Fe and Cr on corrosion behavior of ZrFeCr alloys in 500 oC steam

International Nuclear Information System (INIS)

Wang Jun; Fan Hongyuan; Xiong Ji; Liu Hong; Miao Zhi; Ying Shihao; Yang Gang

2011-01-01

Research highlights: Amount and size of SPP will effect the corrosion resistance of Zr alloy at 500 o C/10.3 MPa. - Abstract: A study of the corrosion behaviors of ZrFeCr alloy and the influence of microstructure on corrosion resistance are described by X-ray diffraction and scanning electron microscope in this paper. The results show that several ZrFeCr alloys exhibit protective behavior throughout the test and oxide growth is stable and protective. The best alloy has the composition Zr1.0Fe0.6Cr. Fitting of the weight gain curves for the protective oxide alloys in the region of protective behavior, it showed nearly cubic behavior for the most protective alloys. The Zr1.0Fe0.6Cr has the more laves Zr(Fe,Cr) 2 precipitate in matrix and it has the better corrosion resistance. The Zr0.2Fe0.1Cr has little precipitate, the biggest hydrogen absorption and the worst corrosion resistance. The number of precipitates and the amount of hydrogen absorption in Zr alloy plays an important role on corrosion resistance behaviors in 500 o C/10.3 MPa steam.

75 FR 6112 - Approval and Promulgation of Air Quality Implementation Plans; Georgia: Update to Materials...

Science.gov (United States)

2010-02-08

...) Incinerators........ 6/15/98 12/2/99, 64 FR 67491 391-3-1-.02(2)(d) Fuel-burning 1/17/79 9/18/79, 44 FR 54047...-.02(2)(aa) VOC Emissions from 1/9/91 10/13/92, 57 FR 46780 Wire Coating. 391-3-1-.02(2)(bb) Petroleum...)(lll) NOX Emissions from 2/16/00 7/10/01, 66 FR 35906 Fuel-burning Equipment. 391-3-1-.02(2)(mmm) NOX...

Microstructure and magnetic properties of Sm(CobalFexCu0.128Zr0.02)7.0 magnets with Fe substitution

International Nuclear Information System (INIS)

Tang, W.; Zhang, Y.; Hadjipanayis, G.C.

2000-01-01

The effect of Fe substitution on the microstructure and magnetic properties of Sm(Co bal Fe x Cu 0.128 Zr 0.02 ) 7.0 magnets was systematically studied. With increasing Fe content (x=0-0.25), the cellular structure changes from a fine inhomogeneous (the average cell size is 25 nm.) to a larger but uniform cell size (120 nm), and finally to coarse and inhomogeneous (180 nm). The coercivity gradually increases reaching an optimal value of 30 kOe with x=0.2, and then drops sharply with further Fe increase. These results suggest that Fe mainly goes into the 2 : 17R structure and stabilizes the phase. The addition of a certain amount of Fe is necessary to develop a uniform cellular with a larger cell size and thus a high coercivity. The excessive addition of Fe hinders the transformation of 2 : 17R to 2 : 17H structure during a solid solution and leads to the disappearance of the cellular microstructure and deterioration of coercivity

Magnetic behaviour of nano-particles of Fe2.8Zn0.2O4

Indian Academy of Sciences (India)

Magnetic behaviour of nano-particles of Fe2.8Zn0.2O4. SUBHASH CHANDER, SEEMA LAKHANPAL, ANJALI KRISHNAMURTHY,. BIPIN K SRIVASTAVA and V K ASWAL∗. Department of Physics, University of Rajasthan, Jaipur 302 004, India. *Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400 ...

Airworthiness Certification of Fe-Si3N4-graphite Brake Composites for Military Aircraft

Directory of Open Access Journals (Sweden)

T.R. Prabhu

2015-12-01

Full Text Available Metal matrix hybrid composites are usually preferred for high energy aircraft (1-10 MJ brake pads (HEABP applications. The report focuses mainly on the evaluation of the wear and braking performance of the composite for the military aircraft applications. In this paper, the design and processing of a typical HEABP composite have been discussed in detail. The airworthiness qualification tests for the HEABP and the brake units are outlined with details. Also, brake testing parameters calculations derived from the typical aircraft data are presented for both the laboratory and full scale dynamometer tests. A case study of Fe-Si3N4- graphite composite pads is presented to exemplify the steps involved in the design, development, and airworthiness certification of HEABPs for the 8 MJ energy military aircraft. From the microstructure and wear surface morphology analysis and the results of brake performance parameters, functional tests and aircraft trials, it is concluded that the Fe-Si3N4- graphite composite has a minimum life of 200 normal energy landings with excellent braking performances.

Electric-field tunable perpendicular magnetic anisotropy in tetragonal Fe4N/BiFeO3 heterostructures

Science.gov (United States)

Yin, Li; Wang, Xiaocha; Mi, Wenbo

2017-07-01

Electric field control on perpendicular magnetic anisotropy (PMA) is indispensable for spintronic devices. Herewith, in tetragonal Fe4N/BiFeO3 heterostructures with the FeAFeB/Fe-O2 interface, PMA in each Fe4N layer, not merely interfacial layers, is modulated by the electric field, which is attributed to the broken spin screening of the electric field in highly spin-polarized Fe4N. Moreover, the periodical dx y+dy z+dz2 and dx y+dx2-y2 orbital-PMA oscillation enhances the interactions between adjacent FeAFeB and (FeB)2N atomic layers, which benefits the electric field modulation on PMA in the whole Fe4N atomic layers. The electric-field control on PMA in Fe4N/BiFeO3 heterostructures is favored by the electric-field-lifted potential in Fe4N.

VTVH-MCD and DFT studies of thiolate bonding to [FeNO]7/[FeO2]8 complexes of isopenicillin N synthase: substrate determination of oxidase versus oxygenase activity in nonheme Fe enzymes.

Science.gov (United States)

Brown, Christina D; Neidig, Michael L; Neibergall, Matthew B; Lipscomb, John D; Solomon, Edward I

2007-06-13

Isopenicillin N synthase (IPNS) is a unique mononuclear nonheme Fe enzyme that catalyzes the four-electron oxidative double ring closure of its substrate ACV. A combination of spectroscopic techniques including EPR, absorbance, circular dichroism (CD), magnetic CD, and variable-temperature, variable-field MCD (VTVH-MCD) were used to evaluate the geometric and electronic structure of the [FeNO]7 complex of IPNS coordinated with the ACV thiolate ligand. Density Function Theory (DFT) calculations correlated to the spectroscopic data were used to generate an experimentally calibrated bonding description of the Fe-IPNS-ACV-NO complex. New spectroscopic features introduced by the binding of the ACV thiolate at 13 100 and 19 800 cm-1 are assigned as the NO pi*(ip) --> Fe dx2-y2 and S pi--> Fe dx2-y2 charge transfer (CT) transitions, respectively. Configuration interaction mixes S CT character into the NO pi*(ip) --> Fe dx2-y2 CT transition, which is observed experimentally from the VTVH-MCD data from this transition. Calculations on the hypothetical {FeO2}8 complex of Fe-IPNS-ACV reveal that the configuration interaction present in the [FeNO]7 complex results in an unoccupied frontier molecular orbital (FMO) with correct orientation and distal O character for H-atom abstraction from the ACV substrate. The energetics of NO/O2 binding to Fe-IPNS-ACV were evaluated and demonstrate that charge donation from the ACV thiolate ligand renders the formation of the FeIII-superoxide complex energetically favorable, driving the reaction at the Fe center. This single center reaction allows IPNS to avoid the O2 bridged binding generally invoked in other nonheme Fe enzymes that leads to oxygen insertion (i.e., oxygenase function) and determines the oxidase activity of IPNS.

THERMAL EXPANSION BEHAVIOR OF THE Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF WITH Sm0.2Ce0.8O1.9

Directory of Open Access Journals (Sweden)

M. AHMADREZAEI

2014-03-01

Full Text Available Nanostructured perovskite oxides of Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF were synthesized through the co-precipitation method. The thermal decomposition, phase formation and thermal expansion behavior of BSCF were characterized by thermogravimetric analysis, X-ray diffraction (XRD, and dilatometry, respectively. XRD peaks were indexed to a cubic perovskite structure with a Pm3m (221 space group. All the combined oxides produced the desired perovskite-phase BSCF. The microstructures were characterized by scanning electron microscopy (SEM and transmission electron microscopy (TEM. The TEM analysis showed that BSCF powders had uniform nanoparticle sizes and high homogeneity. The cross-sectional SEM micrograph of BSCF exhibited a continuous and no delaminated layer from the electrolyte-supported cell. The thermal expansion coefficient (TEC of BSCF was 16.2×10-6 K-1 at a temperature range of 600°C to 800°C. Additional experiments showed that the TEC of BSCF is comparable to that of Sm0.2Ce0.8O1.9 (SDC within the same temperature range. The results demonstrate that BSFC is a promising cathode material for intermediate-temperature solid-oxide fuel cells.

Equilibrium constant and nitrogen activity and the parameters of interaction eN(N), rN(N,Cr), rN(N,Mn) in high nitrogen steels of Fe-Cr-Mn-N type

International Nuclear Information System (INIS)

Svyazhin, A.G.; Siwka, J.; Rashev, T.

1999-01-01

In the paper a description of a thermodynamic of liquid solutions of Fe-Cr-Mn-N type with using a concept of parameters of an interaction has been presented. A temperature relationship of the equilibrium constant K N(Fe) and values of self interaction parameters e N (N) , r N (N,Cr) , r N (N,Mn) and t N (N,Cr,Cr) has been determined for mean values of temperatures of liquid metal equal 1990 K and 2090 K. By application of a theory of regular solutions those values were recalculated for a temperature 1873 K. (orig.)

Precise measurement of the neutron capture reaction 54Fe(n,γ)55Fe via AMS

International Nuclear Information System (INIS)

Wallner, A; Buczak, K; Forstner, O; Golser, R; Kutschera, W; Lederer, C; Priller, A; Steier, P; Belgya, T; Szentmiklosi, L; Bichler, M; Coquard, L; Dillmann, I; Kaeppeler, F; Mengoni, A; Reifarth, R

2010-01-01

The measurement of cross sections relevant to nuclear astrophysics has become one main research topic at the VERA (Vienna Environmental Research Accelerator) facility. The technique applied, accelerator mass spectrometry (AMS), offers excellent sensitivity for the detection of long-lived radionuclides through ultra-low isotope ratio measurements. We discuss the potential and preliminary results of ongoing precision measurements of neutron-capture cross sections of 54 Fe. Such measurements might help to clarify the recently found discrepancy of s-process nucleosynthesis at lower-mass nuclei (A 55 Fe (t 1/2 = 2.72 yr) was analyzed using AMS. At VERA, detection of 55 Fe was developed with a reproducibility of about 1%, which makes the 54 Fe(n,γ) 55 Fe reaction a precise and unique laboratory measurement, which can serve as a reference to complementary techniques. In this regard a new 55 Fe standard for AMS measurements was produced. The final cross-section data are expected to be accurate to better than 3%. We report a preliminary, however, already significantly improved thermal neutron cross section value of (2.32 ± 0.10) barn, and a value of (6.3 ± 0.6) mbarn for E n = (520 ± 50) keV.

Separation of Cu, In, Fe and Sn from nuclear grade thorium by tri-n-octyl amine--5 M HCI and their determination by atomic absorption spectrophotometry

Energy Technology Data Exchange (ETDEWEB)

de Moraes, S; Cipriani, M; Abrao, A

1976-03-01

The results of solvent extraction separation of a group of metal traces in high pure thorium with the aid of tri-n-octyl amine-benzene from ThCl/sub 4/HCl are summarized. ThCl/sub 4/HCl-KI solutions of Cu, In, Fe and Sn are extracted together and determined by atomic absoprtion spectrophotometry and burning directly the organic phase. The behavior of Cu, In, Fe and Sn toward direct burn of the organic phase using hydrogen-air mixture was studied, and an absorption enhancement was observed. The procedure is being used to perform the quality control of nuclear grade thorium and its compounds. The calibration curves have provided precisions in the range 1 to 10% in analysis of thorium.

The crystal structure of ramdohrite Pb_5.9Fe_0.1Mn_0.1In_0.1Cd_0.2Ag_2.8Sb_10.8S₂₄

DEFF Research Database (Denmark)

Makovicky, Emil; Mumme, William G.; Gable, Robert W.

2013-01-01

The crystal structure of ramdohrite, Pb5.9Fe0.1Mn0.1In0.1Cd0.2Ag2.8Sb10.8S24, from the Chocaya mine, Potosí, Bolivia, determined by Makovicky and Mumme from film data in 1983, was refined from single-crystal diffractometer data to the R value 0.060, based on 5230 reflections [I > 2σ(I)] from...... a twinned crystal. Lattice parameters are a = 8.7348(3), b = 13.0543(4), c = 19.3117(6) Å, and β = 90.179(2)°, space group P21/n. Two bicapped trigonal prismatic sites of lead bridge and unite adjacent (311)PbS slabs. These slabs contain five distinct coordination pyramids of Sb with trapezoidal cross...... sections, a mixed and disordered Sb-Ag-Cd-(Pb) site, refined as 0.39 Sb + 0.61 Ag, a pure Ag site with a very open, irregular tetrahedral coordination, and an octahedral site occupied by Pb. The (311)PbS slabs contain large lone electron pair micelles formed by four distinct antimony sites in alternation...

[The cytotoxicity of N48 NdFeB magnets coated with titanium-nitride].

Science.gov (United States)

Cao, Xiao-Ming; Hou, Zhi-Ming; Chu, Ming

2008-04-01

To evaluate the effect of N48 NdFeB magnets coated with titanium-nitride on the growth and apoptosis of L929 mouse fibroblast cells, and to determine the material biocompatibility. The NdFeB magnets coated with titanium-nitride, bare NdFeB magnets and ordinary brackets were put into RPMI-1640 to prepare fusions. L929 mouse fibroblast cells were cultivated in the negative control liquid, positive control liquid, 100%, 50% and 25% sample fusions, respectively. The cell proliferation vitality was detected by MTT assay and the relative growth rate was calculated.Cell scatter diagrams of the negative control liquid, 100% titanium-nitride coated magnets fusion and bare magnets fusion were detected by flow cytometry Annexin V/PI double staining method. The ratios of normal cells, early apoptosis, advanced apoptosis and necrosis cells were calculated. The results were analyzed for paired t test using SPSS11.5 software package. The toxic levels of N48 NdFeB coated with titanium-nitride were ranked as 0-1. The toxic levels of bare magnets were ranked as 2. The cell scatter diagrams showed that there was no significant difference in living cell, early apoptosis and necrosis between magnets coated with titanium-nitride and control group. But there was significant difference between the bare magnets group and control group. The N48 NdFeB magnets coated with titanium-nitride have good biocompatibility.

Magnetic properties of co-modified Fe,N-TiO2 nanocomposites

Directory of Open Access Journals (Sweden)

Zolnierkiewicz Grzegorz

2015-01-01

Full Text Available Iron and nitrogen co-modified titanium dioxide nanocomposites, nFe,N-TiO2 (where n = 1, 5 and 10 wt% of Fe, were investigated by detailed dc susceptibility and magnetization measurements. Different kinds of magnetic interactions were evidenced depending essentially on iron loading of TiO2. The coexistence of superparamagnetic, paramagnetic and ferromagnetic phases was identified at high temperatures. Strong antiferromagnetic interactions were observed below 50 K, where some part of the nanocomposite entered into a long range antiferromagnetic ordering. Antiferromagnetic interactions were attributed to the magnetic agglomerates of iron-based and trivalent iron ions in FeTiO3 phase,whereas ferromagnetic interactions stemmed from the F-center mediated bound magnetic polarons.

Synthesis and electrocatalytic properties of La0.8Sr0.2FeO3−δ perovskite oxide for oxygen reactions

Directory of Open Access Journals (Sweden)

R.A. Silva

2017-09-01

Full Text Available Perovskites are important alternatives for precious metals as catalysts for bifunctional oxygen electrodes, involving oxygen evolution (OER and reduction (ORR reactions as is the case of regenerative fuel cells. In this work, strontium doped lanthanum ferrite La1−xSrxFeO3−δ (x = 0; 0.1; 0.2; 0.3; 0.4; 0.6 and 1.0 powders were prepared by a self-combustion route. The oxides, in the form of carbon paste electrodes, were characterised by cyclic voltammetry in alkaline solutions. Data analyses lead to the selection of La0.8Sr0.2FeO3−δ to prepare gas diffusion electrodes (GDEs. Cyclic voltammetry and steady state polarization curves were used, respectively, to assess the electrochemical behaviour of GDEs and to obtain kinetic data for both OER and ORR. It is concluded that the oxide preparation conditions/electrode configuration determine the electrode performance. The bifunctionality of the electrodes was assessed, under galvanostatic control, using a cycling protocol within the potential domains for OER and ORR. The potential window, i.e., the total combined overpotential between OER and ORR was found to be of ≈770 mV, value which compares well with that obtained under potentiostatic control. Even though the potential window keeps constant during 140 cycles, the increase in cycling time and/or current density (≥2.5 mA·cm−2 led to a gradual metallization of the GDE surface, as confirmed by Scanning Electron Microscopy and X-ray diffraction analysis.

Propiedades mecánicas y mecanismos de deformación en aleaciones del sistemas Fe-xMn-3,2Al-0,2C (12 ≤ x ≤ 43

Directory of Open Access Journals (Sweden)

Rodríguez, V. F.

1998-05-01

Full Text Available Microstructure and mechanical properties of Fe-xMn-3,2Al-0,23C alloys with 12 ≤ x ≤ 43 (mass % at 77 and 290 K have been studied to determine the mechanisms controlling plastic deformation. Austenitic alloys (Mn ≥ 22 show an increase of elongation to failure with decreasing temperature of testing (inverse ductility. This behavior has been related to formation of deformation twins, which is favored at 77 K. Alloys with manganese content lower than 17 % present a two-phase microstructure (α' + γ. The martensite volume fraction increases as the manganese content decreases. These alloys show a loss of ductility, especially at 77 K. In contrast to asutenitic alloys, this different mechanical behavior has been associated with a TRIP mechanism (transformationinduced plasticity.

Se han estudiado la microestructura y las propiedades mecánicas a 77 y 290 K de una serie de aleaciones Fe-xMn-3,2Al-0,23C con 12 ≤ x ≤ 43 (% en masa con objeto de determinar los mecanismos que controlan la deformación plástica. Se ha comprobado que, en las aleaciones con estructura austenítica (Mn ≥ 22, el alargamiento a rotura aumenta al disminuir la temperatura de ensayo (ductilidad inversa. Este comportamiento se ha relacionado con un proceso de deformación por maclaje favorecido a 77 K. Las aleaciones con contenidos de manganeso < 17 % presentan una estructura bifásica (α' + γ, siendo mayor la fracción de volumen de martensita a medida que disminuye la concentración de manganeso. Estas aleaciones presentan una disminución del alargamiento a rotura especialmente a 77 K. El diferente comportamiento mecánico con respecto al de las aleaciones austeníticas se asocia a un proceso de transformación a martensita inducida por deformación (TRIP.

Determination of iron in plutonium by extraction of the Fe (2): Bathophenanthroline complex

International Nuclear Information System (INIS)

Pichotin, B.; Chasseur, Ph.

1966-06-01

The present report describes the method to determine micro quantities of iron in plutonium, by extraction with hexyl alcohol of the complex that give iron (II) with bathophenanthroline (4,7 diphenyl - 1.10 phenanthroline). The reagent has been applied to the determination of amounts of iron ranging from 1 to 10 μg in 20 ml of solvent The determination is made by spectrophotometry at 530 mμ. Others cations present do not interfere. (authors) [fr

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe; Comportamiento de naranja de metilo y naranja 10 (orange G) en presencia de compuestos tipo hidrotalcita de mg/Al y Mg/Fe

Energy Technology Data Exchange (ETDEWEB)

Cruz N, G.

2015-07-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m{sup 2}/g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99

Study of the interference of uranium, vanadium, aluminium and molebdenum in the determination of FeII, FeIII in Syrian phosphoric acid by spectrophotometry

International Nuclear Information System (INIS)

Zaizafoun, Ghadir; Elian, Nazha

1991-04-01

The spectrophotometric determination of the ratio of iron I I to iron I II in crude phosphoric acid is of great importance because of its influence on the redox potential in the different stages which lead to the extraction of uranium from crude phosphoric acid. The suitability of a number of reagents for this determination was examined and only 1,10-phenanthroline, 5-sulfosalicylic acid and 2,2'-bipyridine were selected for further experimentation. 1-10-phenanthroline can give a deep red complex with Fe I I, in phosphoric acid medium at PH 4-6, absorbs at λ = 510 nm. The total iron was determined by reducing Fe I II to Fe I I using hydroxylamine hydrochloride. The second reagent was found capable of forming a yellow complex absorbs light at λ = 430 nm in amonia medium at PH 8.5 - 11 with Fe I II. The adopted procedure was to determine total iron first by oxidation with nitric acid. Then iron I I was determined in a second test at PH 1.5 and at λ = 500 nm. The third reagent i.e. 2-2' bipyridine is capable of forming a red complex with iron I I absorbs at λ = 522 nm. The interference of U, V, Al, and Mo was investigated. These elements were selected because of their presence in considerable amounts in Syrian commercial phosphoric acid. The work was designed so that the effect of the presence of each element as well as the presence of all possible combinations of these elements can be estimated. The investigation revealed that the interference is very high in the case of 2-2' bipyridine in addition to the instability of the complex. In the case of 1,10-phenanthroline the interference was also found high. Thus these two reagents were disregarded. The 5-sulfosalicylic reagent was found satisfactory when determining iron I II, However when Fe I I is considered the error resulting from interference ranges between 17.5 - 50%. This error was found very dependent on the PH of the medium and further work is in progress in order to lower the value of interferences

Competing ferromagnetic and anti-ferromagnetic interactions in iron nitride ζ-Fe2N

Science.gov (United States)

Rao, K. Sandeep; Salunke, H. G.

2018-03-01

The paper discusses the magnetic state of zeta phase of iron nitride viz. ζ-Fe2N on the basis of spin polarized first principles electronic structure calculations together with a review of already published data. Results of our first principles study suggest that the ground state of ζ-Fe2N is ferromagnetic (FM) with a magnetic moment of 1.528μB on the Fe site. The FM ground state is lower than the anti-ferromagnetic (AFM) state by 8.44 meV and non-magnetic (NM) state by 191 meV per formula unit. These results are important in view of reports which claim that ζ-Fe2N undergoes an AFM transition below 10 K and others which do not observe any magnetic transition up to 4.2 K. We argue that the experimental results of AFM transition below 10 K are inconclusive and we propose the presence of competing FM and AFM superexchange interactions between Fe sites mediated by nitrogen atoms, which are consistent with Goodenough-Kanamori-Anderson rules. We find that the anti-ferromagnetically coupled Fe sites are outnumbered by ferromagnetically coupled Fe sites leading to a stable FM ground state. A Stoner analysis of the results also supports our claim of a FM ground state.

Spacer layer effect and microstructure on multi-layer [NdFeB/Nb]n films

International Nuclear Information System (INIS)

Tsai, J.-L.; Yao, Y.-D.; Chin, T.-S.; Kronmueller, H.

2002-01-01

Spacer layer effect on multi-layer [NdFeB/Nb] n films has been investigated from the variation of magnetic properties and microstructure of the films. From a HRTEM cross-section view observation, the average grain size of [NdFeB/Nb] n multi-layers was controlled by both annealing temperature and thickness of NdFeB layer. Selected area diffraction pattern indicated that the structure of Nb spacer layer was amorphous. The grain size and coercivity of [NdFeB x /Nb] n films change from 50 nm and 16.7 kOe to 167 nm and 9 kOe for films with x=40 nm, n=10 and x=200 nm, n=2, respectively

Determining the spin dependent mean free path in Co90Fe10 using giant magnetoresistance

Science.gov (United States)

Shakespear, K. F.; Perdue, K. L.; Moyerman, S. M.; Checkelsky, J. G.; Harberger, S. S.; Tamboli, A. C.; Carey, M. J.; Sparks, P. D.; Eckert, J. C.

2005-05-01

The spin dependent mean free path in Co90Fe10 is determined as a function of temperature down to 5K using two different spin valve structures. At 5K the spin dependent mean free path for one structure was measured to be 9.4±1.4nm, decreasing by a factor of 3 by 350K. For the other structure, it is 7.5±0.5nm at 5K and decreased by a factor of 1.5 by 350K. In both cases, the spin dependent mean free path approaches the typical thickness of ferromagnetic layers in spin valves at room temperature and, thus, has an impact on the choice of design parameters for the development of new spintronic devices.

Tuning high frequency magnetic properties and damping of FeGa, FeGaN and FeGaB thin films

Directory of Open Access Journals (Sweden)

Derang Cao

2017-11-01

Full Text Available A series of FeGa, FeGaN and FeGaB films with varied oblique angles were deposited by sputtering method on silicon substrates, respectively. The microstructure, soft magnetism, microwave properties, and damping factor for the films were investigated. The FeGa films showed a poor high frequency magnetic property due to the large stress itself. The grain size of FeGa films was reduced by the additional N element, while the structure of FeGa films was changed from the polycrystalline to amorphous phase by the involved B element. As a result, N content can effectively improve the magnetic softness of FeGa film, but their high frequency magnetic properties were still poor both when the N2/Ar flow rate ratio is 2% and 5% during the deposition. The additional B content significantly led to the excellent magnetic softness and the self-biased ferromagnetic resonance frequency of 1.83 GHz for FeGaB film. The dampings of FeGa films were adjusted by the additional N and B contents from 0.218 to 0.139 and 0.023, respectively. The combination of these properties for FeGa films are helpful for the development of magnetostrictive microwave devices.

49 CFR 1242.10 - Administration-track (account XX-19-02).

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Administration-track (account XX-19-02). 1242.10... Structures § 1242.10 Administration—track (account XX-19-02). Separate common administration—track expenses... accounts are separated between freight and passenger services: Roadway: Running (XX-17-10) Switching (XX-18...

Synthesis of Nano-Structured La0.6Sr0.4Co0.2Fe0.8O3 Perovskite by Co-Precipitation Method

Directory of Open Access Journals (Sweden)

Ebrahim Mostafavi

2015-06-01

Full Text Available Nano-structured lanthanum strontium cobalt ferrite, La0.6Sr0.4Co0.2Fe0.8O3 (LSCF, was successfully synthesized via co-precipitation method using metal nitrates as starting materials. Effects of precipitating agent and calcination temperature on the phase composition and morphology of synthesized powders were systematically studied using X-ray diffraction (XRD and field emission scanning electron microscopy (FESEM, respectively. XRD analysis revealed that a single phase La0.6Sr0.4Co0.2Fe0.8O3 perovskite was obtained in the processed sample using ammonium carbonate as precipitating agent with a NH4+/NO3-molar ratio of 2 after calcination at 1000C for 1 h. The phase composition of products was also affected by changing pH values. Moreover, using sodium hydroxide as a precipitant resulted in a mixture of La0.6Sr0.4Co0.2Fe0.8O3 and cobalt ferrite (CoFe2O4 phases. Careless washing of the precursors can also led to the formation of mixed phase after calcination of final powders. Mean crystallite size of the obtained powders was not noticeably affected by varying calcination temperature from 900 to 1050C and remained almost the same at 10 nm, however increasing calcination temperature to 1100C resulted in sharp structural coarsening. FESEM studies demonstrate that relatively uniform particles with mean particle size of 90 nm were obtained in the sample processed with a NH4+/NO3- molar ratio of 2 after calcination at 1000C for 1 h.

Thermal stability of ultrasoft Fe-Zr-N films

NARCIS (Netherlands)

Chechenin, NG; van Veen, A; Schut, H; Chezan, AR; Boerma, D; Vystavel, T; De Hosson, JTM

2003-01-01

The thermal stability of nanocrystalline ultrasoft magnetic (Fe98Zr2)(1-x)N-x films with x = 0.10-0.25 was studied using thermal desorption spectrometry, positron beam analysis and high resolution transmission electron microscopy. The results demonstrate that grain growth during the heat treatment

Seasonal changes in Fe along a glaciated Greenlandic fjord.

Directory of Open Access Journals (Sweden)

Mark James Hopwood

2016-03-01

Full Text Available Greenland’s ice sheet is the second largest on Earth, and is under threat from a warming Arctic climate. An increase in freshwater discharge from Greenland has the potential to strongly influence the composition of adjacent water masses with the largest impact on marine ecosystems likely to be found within the glaciated fjords. Here we demonstrate that physical and chemical estuarine processes within a large Greenlandic fjord are critical factors in determining the fate of meltwater derived nutrients and particles, especially for non-conservative elements such as Fe. Concentrations of Fe and macronutrients in surface waters along Godthåbsfjord, a southwest Greenlandic fjord with freshwater input from 6 glaciers, changed markedly between the onset and peak of the meltwater season due to the development of a thin (<10 m, outflowing, low-salinity surface layer. Dissolved (<0.2 µm Fe concentrations in meltwater entering Godthåbsfjord (200 nM, in freshly melted glacial ice (mean 38 nM and in surface waters close to a land terminating glacial system (80 nM all indicated high Fe inputs into the fjord in summer. Total dissolvable (unfiltered at pH <2.0 Fe was similarly high with concentrations always in excess of 100 nM throughout the fjord and reaching up to 5.0 µM close to glacial outflows in summer. Yet, despite the large seasonal freshwater influx into the fjord, Fe concentrations near the fjord mouth in the out-flowing surface layer were similar in summer to those measured before the meltwater season. Furthermore, turbidity profiles indicated that sub-glacial particulate Fe inputs may not actually mix into the outflowing surface layer of this fjord. Emphasis has previously been placed on the possibility of increased Fe export from Greenland as meltwater fluxes increase. Here we suggest that in-fjord processes may be effective at removing Fe from surface waters before it can be exported to coastal seas.

Preparation and properties of [(NdFeB)x/(Nb)z]n multi-layer films

International Nuclear Information System (INIS)

Tsai, J.-L.; Chin, T.-S.; Yao, Y.-D.; Melsheimer, A.; Fisher, S.; Drogen, T.; Kelsch, M.; Kronmueller, H.

2003-01-01

Multi-layer [(NdFeB) x /(Nb) z ] n films with 200 nm≥x≥10 nm, 10 nm≥z≥0, 40≥n≥2, prepared by ion beam sputtering and subsequent annealing, show significantly enhanced coercivity due to the reduced grain size that enhances the anisotropy of individual grains. After annealing at 630 deg. C, some Nd 2 Fe 14 B grains were enriched with Nb and isolated as the thickness of the Nb spacer layer increases. For multi-layer (NdFeB x /Nb z ) n films with 100 nm ≥x≥25 nm, 5 nm≥z≥2 nm, their coercivity and remanence ratio are better than that of a single NdFeB film. Up to 17.8 kOe room temperature coercivity has been obtained for a sample with x=25 nm, z=5 nm and n=16

The use of Yo-Yo IR1 and Andersen testing for fitness and maximal heart rate assessments of 6-10 yr old school children

DEFF Research Database (Denmark)

Ahler, Thomas

2012-01-01

; grade 2, n=16) and six weeks apart by 9-10 year olds (grade 3, n=49). Grade (G) 0-2's also performed an incremental treadmill test (ITT). G2's had a better (pSD) vs 536±218 m) and Andersen test performance (10%; 1050±71 vs 955±56 m) than G0's. For G0-2's YYIR1C......-10 year old children. Additionally, submaximal YYIR1C testing can be used for frequent non-exhaustive fitness assessments....

Room temperature luminescence and ferromagnetism of AlN:Fe

Energy Technology Data Exchange (ETDEWEB)

Li, H., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [The Key Laboratory of Solar Thermal Energy and Photovoltaic System, Institute of Electrical engineering, Chinese Academy of Sciences, Beijing 100190 (China); Cai, G. M. [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); Wang, W. J., E-mail: lihui@mail.iee.ac.cn, E-mail: wjwang@aphy.iphy.ac.cn [Research and Development Center for Functional Crystals, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

2016-06-15

AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR) method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe{sup 2+} state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV) and 598 nm (2.07 eV) are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

Effect of heat input on microstructure, wear and friction behavior of (wt.-%) 50FeCrC-20FeW-30FeB coating on AISI 1020 produced by using PTA welding.

Science.gov (United States)

Özel, Cihan; Gürgenç, Turan

2018-01-01

In this study, AISI 1020 steel surface was coated in different heat inputs with (wt.-%) 50FeCrC-20FeW-30FeB powder mixture by using plasma transferred arc (PTA) welding method. The microstructure of the coated samples were investigated by using optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive X-ray (EDS). The hardness was measured with micro hardness test device. The dry sliding wear and friction coefficient properties were determined using a block-on-disk type wear test device. Wear tests were performed at 19.62 N, 39.24 N, 58.86 N load and the sliding distance of 900 m. The results were shown that different microstructures formed due to the heat input change. The highest average micro hardness value was measured at 1217 HV on sample coated with low heat input. It was determined that the wear resistance decreased with increasing heat input.

Oxygen tracer diffusion and surface exchange kinetics in Ba0.5Sr0.5Co0.8Fe0.2O3-δ

NARCIS (Netherlands)

Berenov, A.; Atkinson, A.; Kilner, J.; Ananyev, M.; Eremin, V.; Porotnikova, N.; Farlenkov, A.; Kurumchin, E.; Bouwmeester, Henricus J.M.; Bucher, E.; Sitte, W.

2014-01-01

The oxygen tracer diffusion coefficient, Db⁎, and the oxygen tracer surface exchange coefficient, k, were measured in Ba0.5Sr0.5Co0.8Fe0.2O3 − δ (BSCF5582) over the temperature range of 310–800 °C and the oxygen partial pressure range of 1.3 × 10−3–0.21 bar. Several measurement techniques were used:

Magnetic ordering and electrical resistivity in Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} spinel oxide

Energy Technology Data Exchange (ETDEWEB)

Bhowmik, R.N. [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700065 (India)], E-mail: rabindranath.bhowmik@saha.ac.in; Ranganathan, R. [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700065 (India); Ghosh, B.; Kumar, S. [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Chattopadhyay, S. [Department of Physics, University of Calcutta, 92, A.P.C. Road, Kolkata 700009 (India)

2008-05-29

We report the magnetic, Moessbauer spectroscopy and resistivity measurements in order to understand the electronic behaviour of bulk Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} spinel oxide. The effect of magnetic order on electrical behaviour is observed from the resistivity measurements in the absence and presence of magnetic field. The analysis of Moessbauer spectra suggests the absence of Fe{sup 2+} ions in the system, which implies that complete hopping of charge carriers between localized Fe{sup 3+}/Co{sup 2+} and Fe{sup 2+}/Co{sup 3+} pair of ions in B sublattice is not the favourable mechanism in Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4}. We suggest that electrical behaviour of the present sample may be consistent with a model of fractional charge transfer via Fe{sub B}{sup 3+}-O{sup 2-}-Co{sub B}{sup 2+} superexchange path.

Evaluations of the 58Fe(n,γ)59Fe, and 54Fe(n,p)54Mn reactions for the ENDF/B-V dosimetry file

International Nuclear Information System (INIS)

Schenter, R.E.; Schmittroth, F.; Mann, F.M.

1979-10-01

A generalized least-squares adjustment procedure was used to evaluate two important dosimetry reactions for the ENDF/B-V files. Calculations for the cross section adjustments were made with the computer code FERRET, where input data included both integral and differential experimental data results. For the 54 Fe reaction, important ratio measurements were renormalized to ENDF/B-V evaluations of 235 U(n,f), 238 U(n,f), and 56 Fe(n,p). A priori curves which are required for the calculations were obtained using Hauser-Feshbach calculations from the codes NCAP ( 58 Fe) and HAUSER-5 ( 54 Fe). Covariance matrices were also calculated and are included in the evaluations. 8 figures, 1 table

Colorimetric determination of Fe2+/Fe3+ ratio in radioactive glasses

International Nuclear Information System (INIS)

Coleman, C.J.; Baumann, E.W.; Bibler, N.E.

1992-01-01

In the vitrification of nuclear wastes, the Fe 2+ /Fe 3+ ratio in the glass is a measure of the redox properties of the glass melt. It is necessary to measure this ratio to ensure that the melt redox properties are suitable for the glass melter. A colorimetric method for measuring the Fe 2+ /Fe 3+ ratio in highly radioactive glasses was developed and tested remotely in a shielded cell. The tests were performed on glasses similar in composition and radioactivity to those that will be produced in the Savannah River Site Defense Waste Processing Facility. The first step of the method is dissolution of finely crushed glass with a hydrofluoric/sulfuric acid mixture with ammonium vanadate added to preserve the Fe 2+ content of the glass during the dissolution. Boric acid is then added to complex fluoride and to destroy iron-fluoride complexes. After adjusting the solution to pH 5, FerroZine TM (trademark of the Hach Company, Loveland, CO) reagent is added to form a magenta-colored complex with Fe 2+ . The absorbance at 562 nm is measured by using a fiber optic-coupled photodiode array spectrophotometer. Ascorbic acid is then used to reduce all the iron in solution to Fe 2+ and the absorbance is again measured. The difference in absorbance measurements corresponds to the Fe 3+ in the sample and the Fe 2+ /Fe 3+ ratio can be calculated

Crystal structure of superparamagnetic Mg0.2Ca0.8Fe2O4 nanoparticles synthesized by sol–gel method

International Nuclear Information System (INIS)

Escamilla-Pérez, A.M.; Cortés-Hernández, D.A.; Almanza-Robles, J.M.; Mantovani, D.; Chevallier, P.

2015-01-01

Powders of magnetic iron oxide nanoparticles (Mg 0.2 Ca 0.8 Fe 2 O 4 ) were prepared by a sol–gel method using ethylene glycol and nitrates of Fe, Ca and Mg as starting materials. Those powders were heat treated at different temperatures (573, 673, 773 and 873 K). In order to evaluate the effect of the heat treatment temperature on the nanoferrites properties, X-ray diffraction (XRD), vibrating sample magnetometry (VSM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques were used. It was found that the reaction products exhibit nanometric sizes and superparamagnetic behavior. It is also demonstrated that, as the heat treatment temperature increases, the particle size and the saturation magnetization of the nanoferrites are increased. - Highlights: • Mg 0.2 Ca 0.8 Fe 2 O 4 superparamagnetic nanoparticles were successfully synthesized. • Particle average sizes of Ca–Mg ferrites were within the range of 8–25 nm. • The nanoferrite treated at 873 K showed a stoichiometry close to Mg 0.2 Ca 0.8 Fe 2 O 4 . • The heat treatment temperature has a strong effect on the crystal structure. • These nanoparticles are potential materials for magnetic hyperthermia

Room temperature luminescence and ferromagnetism of AlN:Fe

Directory of Open Access Journals (Sweden)

H. Li

2016-06-01

Full Text Available AlN:Fe polycrystalline powders were synthesized by a modified solid state reaction (MSSR method. Powder X-ray diffraction and transmission electron microscopy results reveal the single phase nature of the doped samples. In the doped AlN samples, Fe is in Fe2+ state. Room temperature ferromagnetic behavior is observed in AlN:Fe samples. Two photoluminescence peaks located at about 592 nm (2.09 eV and 598 nm (2.07 eV are observed in AlN:Fe samples. Our results suggest that AlN:Fe is a potential material for applications in spintronics and high power laser devices.

Studies of N{sub 2}0 adsorption and decomposition on Fe-ZSM-5

Energy Technology Data Exchange (ETDEWEB)

Wood, Benjamin R.; Reimer, Jeffrey A.; Bell, Alexis T.

2002-03-08

The interactions of N2O with H-ZSM-5 and Fe-ZSM-5 have been investigated using infrared spectroscopy and temperature-programmed reaction. Fe-ZSM-5 samples with Fe/Al ratios of 0.17 and 0.33 were prepared by solid-state exchange. It was determined that most of the iron in the samples of Fe-ZSM-5 is in the form of isolated cations, which have exchanged with Bronsted acid H+ in H-ZSM-5. The infrared spectrum of N2O adsorbed on H-ZSM-5 at 298 K exhibits bands at 2226 and 1308 cm-1 associated with vibrations of the N-N and N-O bonds, respectively. The positions of these bands relative to those seen in the gas phase suggest that N2O adsorbs through the nitrogen end of the molecule. The heat of N2O adsorption in H-ZSM-5 is estimated to be 5 kcal/mol. In the case of Fe-ZSM-5, additional infrared bands are observed at 2282 and 1344 cm-1 due to the interactions of N2O with the iron cations. Here too, the directions of the shifts in the vibrational features relative to those for gas-phase N2O suggest that the molecule adsorbs through its nitrogen end. The heat of adsorption of N2O on the Fe sites is estimated to be 16 kcal/mol. The extent of N2O adsorption on Fe depends on the oxidation state of Fe. The degree of N2O adsorption is higher following pretreatment of the sample in He or CO at 773 K, than following pretreatment in O2 or N2O at the same temperature. Temperature-programmed decomposition of N2O was performed on the Fe-ZSM-5 samples and revealed that N2O decomposes stoichiometrically to N2 and O2. A higher activity was observed if the catalysts were pretreated in He than if they were pretreated in N2O. For the He-pretreated samples, the activation energy for N2O decomposition was estimated to be 42 kcal/mol and the preexponential factor of the rate coefficient for this process was found to increase with Fe/Al ratio. This trend was attributed to the increasing auto reducibility of Fe3+ cations to Fe2+ cations with increasing Fe/Al ratio.

Superelasticity, corrosion resistance and biocompatibility of the Ti–19Zr–10Nb–1Fe alloy

Energy Technology Data Exchange (ETDEWEB)

Xue, Pengfei [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Li, Yan, E-mail: liyan@buaa.edu.cn [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Li, Kangming [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Key Laboratory of Aerospace Materials and Performance (Ministry of Education), Beihang University, Beijing 100191 (China); Zhang, Deyuan [Life Tech Scientific Corporation, Shenzhen 518057 (China); Zhou, Chungen [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China)

2015-05-01

Microstructure, mechanical properties, superelasticity and biocompatibility of a Ti–19Zr–10Nb–1Fe alloy are investigated. X-ray diffraction spectroscopy and transmission electron microscopy observations show that the as-cast Ti–19Zr–10Nb–1Fe alloy is composed of α′ and β phases, but only the β phase exists in the as-rolled and as-quenched alloys. The tensile stress–strain tests indicate that the as-quenched alloy exhibits a good combination of mechanical properties with a large elongation of 25%, a low Young's modulus of 59 GPa and a high ultimate tensile stress of 723 MPa. Superelastic recovery behavior is found in the as-quenched alloy during tensile tests, and the corresponding maximum of superelastic strain is 4.7% at the pre-strain of 6%. A superelastic recovery of 4% with high stability is achieved after 10 cyclic loading–unloading training processes. Potentiodynamic polarization and ion release measurements indicate that the as-quenched alloy shows a lower corrosion rate in Hank's solution and a much less ion release rate in 0.9% NaCl solution than those of the NiTi alloys. Cell culture results indicate that the osteoblasts' adhesion and proliferation are similar on both the Ti–19Zr–10Nb–1Fe and NiTi alloys. A better hemocompatibility is confirmed for the as-quenched Ti–19Zr–10Nb–1Fe alloy, attributed to more stable platelet adhesion and small activation degree, and a much lower hemolysis rate compared with the NiTi alloy. - Highlights: • A stable superelastic strain of 4.0% is achieved for the Ti–19Zr–10Nb–1Fe alloy. • The ion release rates of Ti–19Zr–10Nb–1Fe are much lower than that of Ni in NiTi. • Ti–19Zr–10Nb–1Fe has a similar cytocompatibility compared with the NiTi alloy. • Ti–19Zr–10Nb–1Fe exhibits a better hemocompatibility than the NiTi alloy.

Structure and magnetic properties of L10-FePt thin films on TiN/RuAl underlayers

International Nuclear Information System (INIS)

Yang En; Ratanaphan, Sutatch; Zhu Jiangang; Laughlin, David E.

2011-01-01

Highly ordered L1 0 FePt-oxide thin films with small grains were prepared by using a RuAl layer as a grain size defining seed layer along with a TiN barrier layer. Different HAMR (Heat Assisted Magnetic Recording) favorable underlayers were studied to encourage perpendicular texture and preferred microstructure. It was found that the epitaxial and small grain growth from the RuAl/TiN underlayer results in small and uniform grains in the FePt layer with perpendicular texture. By introducing the grain size defining underlayers, the FePt grain size can be reduced from 30 to 6 nm with the same volume fraction (9%) of SiO 2 in the film, excellent perpendicular texture, and very high order parameter at 520 deg. C.

Adrenaline and triiodothyronine modify the iron handling in the freshwater air-breathing fish Anabas testudineus Bloch: role of ferric reductase in iron acquisition.

Science.gov (United States)

Rejitha, V; Peter, M C Subhash

2013-01-15

The effects of in vivo adrenaline and triiodothyronine (T(3)) on ferric reductase (FR) activity, a membrane-bound enzyme that reduces Fe(III) to Fe(II) iron, were studied in the organs of climbing perch (Anabas testudineus Bloch). Adrenaline injection (10 ng g(-1)) for 30 min produced significant inhibition of FR activity in the liver and kidney and that suggests a role for this stress hormone in iron acquisition in this fish. Short-term T(3) injection (40 ng g(-1)) reduced FR activity in the gills of fed fish but not in the unfed fish. Similar reduction of FR activity was also obtained in the intestine and kidney of fed fish after T(3) injection. Feeding produced pronounced decline in FR activity in the spleen but T(3) challenge in fed and unfed fish increased its activity in this iron storing organ and that point to the sensitivity of FR system to feeding activity. The in vitro effects of Fe on FR activity in the gill explants of freshwater fish showed correlations of FR with Na(+), K(+)-ATPase and H(+)-ATPase activities. Substantial increase in the FR activity was found in the gill explants incubated with all the tested doses of Fe(II) iron (1.80, 3.59 and 7.18 μM) and Fe(III) iron (1.25, 2.51 and 5.02 μM) and this indicate that FR and Na pump activity are positively correlated. On the contrary, substantial reduction of gill H(+)-ATPase activity was found in the gill explants incubated with Fe(II) iron and Fe(III) iron indicating that perch gills may not require a high acidic microenvironment for the reduction of Fe(III) iron. Accumulation of iron in the gill explants after Fe(III) iron incubation implies a direct relationship between Fe acquisition and FR activity in this tissue. The inverse correlation between FR activity and H(+)-ATPase activity in Fe(II) or Fe(III) loaded gills and the significant positive correlations of FR activity with total [Fe] content in the Fe(III) loaded gills substantiate that FR which shows sensitivity to sodium and proton pumps

Effect of FeH-zeolite structure and Al-Lewis sites on N2O decomposition and NO/NO2-assisted reaction

Czech Academy of Sciences Publication Activity Database

Kaucký, Dalibor; Sobalík, Zdeněk; Schwarze, Michael; Vondrová, Alena; Wichterlová, Blanka

2006-01-01

Roč. 238, č. 2 (2006), s. 293-300 ISSN 0021-9517 R&D Projects: GA ČR GP104/02/D124; GA AV ČR 1ET400400413 Institutional research plan: CEZ:AV0Z40400503 Keywords : N2O decomposition * NO/NO2 assistance * Fe-zeolites * Fe-ferrierite Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.533, year: 2006

Tris(1,10-phenanthroline-κ2N,N′iron(II bis[(1,10-phenanthroline-κ2N,N′tetrakis(thiocyanato-κNchromate(III] acetonitrile trisolvate monohydrate

Directory of Open Access Journals (Sweden)

Volodymyr V. Bon

2012-05-01

Full Text Available Single crystals of the title heterometallic compound, [Fe(C12H8N23][Cr(NCS4(C12H8N2]2·3CH3CN·H2O or [Fe(Cphen3][Cr(NCS4(phen]2·3CH3CN·H2O, were prepared using the one-pot open-air reaction of iron powder, Reineckes salt and 1,10-phenanthroline (phen in acetonitrile. The asymetric unit consists of an [Fe(phen3]2+ cation, two [Cr(phen(NCS4]− anions, three acetonitrile solvent molecules and a water molecule. The Fe and Cr atoms both show a slightly distorted octahedral FeN6 and CrN6 coordination geometry with adjacent angles in the range 79.67 (12–95.21 (12°. No classical hydrogen bonding involving the water molecule is observed.

Chemical evaluation of HBED/Fe(3+) and the novel HJB/Fe(3+) chelates as fertilizers to alleviate iron chlorosis.

Science.gov (United States)

López-Rayo, Sandra; Hernández, Diana; Lucena, Juan J

2009-09-23

Iron chelates such as ethylenediamine-N,N'-bis(2-hydroxyphenylacetic) acid (o,o-EDDHA) and their analogues are the most efficient soil fertilizers to treat iron chlorosis in plants growing in calcareous soil. A new chelating agent, HJB (N,N'-bis(2-hydroxy-5-methylphenyl)ethylendiamine-N,N'-diacetic acid) may be an alternative to o,o-EDDHA since its synthesis yields a purer product, but its chemical behavior and efficiency as chlorosis corrector should be evaluated. In this research, a known analogous HBED (N,N'-bis(2-hydroxyphenyl)ethylendiamine-N,N'-diacetic acid) has also been considered. First, an ion-pair high performance liquid chromatography (HPLC) method has been tested for the HJB/Fe(3+) and HBED/Fe(3+) determination. The ability of HJB and HBED to maintain Fe in solution has been compared with respect to o,o-EDDHA. Theoretical modelization for HBED and HJB in agronomic conditions has been done after the determination of the protonation and Ca(II), Mg(II), Fe(III), and Cu(II) stability constants for HJB. Also, batch interaction experiments with soils and soil materials have been conducted. According to our results, HJB/Fe(3+) and HBED/Fe(3+) present high stability, even when competing cations (Cu(2+), Ca(2+)) are present, and have low reactivity with soils and soil components. The chelating agent HJB dissolves a higher amount of Fe than o,o-EDDHA, and it seems as effective as o,o-EDDHA in keeping Fe in solution. These results indicate that these chelates may be very efficient products to correct Fe chlorosis, and additional plant experiments should demonstrate plants' ability to assimilate Fe from HJB/Fe(3+) and HBED/Fe(3+).

Structures, stability, magnetic moments and growth strategies of the Fe_nN (n = 1–7) clusters: All-electron density functional theory calculations

International Nuclear Information System (INIS)

Li, Zhi; Zhao, Zhen

2017-01-01

The geometries, electronic properties, magnetic moments and growth strategies of the Fe_nN (n = 1–7) clusters are investigated using all-electron density functional theory. The results show that N doping significantly distorts the Fe_n clusters. Fe_4N and Fe_6N clusters are more stable structures than other considered Fe_nN clusters. Local peaks of HOMO-LUMO gap curve are found at n = 3, 7, implying that the chemical stability of the Fe_3N and Fe_7N clusters is higher. Fe_2N, Fe_4N and Fe_6N clusters have larger magnetic moments compared to other considered Fe_nN (n = 1–7) clusters. It can be seen that the Fe_5 clusters are easier to adsorb a Fe atom while the Fe_4 clusters are easier to adsorb a N atom. The considered Fe_mN clusters prefer to adsorb a Fe atom and larger Fe_mN clusters are easier to grow. - Highlights: • The structural stability of the Fe_4N and Fe_6N clusters is higher. • The chemical stability of the Fe_3N and Fe_7N clusters is higher. • Fe_5 clusters are easier to adsorb a Fe atom while Fe_4 clusters are easier to adsorb a N atom. • Fe_nN clusters prefer to adsorb a Fe atom.

Multi-element determinations of N,N-dimethylformamide (DMF) coal slurries using ICP-OES

Energy Technology Data Exchange (ETDEWEB)

M. Mujuru; R.I. McCrindle; B.M. Botha; P.P. Ndibewu [Tshwane University of Technology, Pretoria (South Africa). Department of Chemistry

2009-04-15

A slurry nebulisation technique was applied for elemental analysis of bituminous coals SARM 18, SARM 19 and four coals from three different seams in Witbank, South Africa, by inductively coupled plasma optical emission spectroscopy (ICP-OES). Major elements (Al, Ca, Fe, Mg, S, Si and Ti) and trace elements (Ba, Cr, Mn, Ni, Sr, V, Zn and Zr) in coal were determined. Various slurry preparations were evaluated using two dispersants (glycerol and Triton X-100) and by varying the concentration of dispersants, between 0.1% and 1.0% (v/v). The effect of initially solubilising the ground coal in N,N-dimethylformamide (DMF) was investigated by varying the volume of DMF added. The effect of wet grinding with DMF was investigated. Wet grinding with DMF was shown to drastically reduce particle sizes (50.0% < 0.28 m and 90.0% < 6.17 {mu}m) as compared to dry grinding (50.0% < 5.25 {mu}m and 90.0% < 11.1 {mu}m). The reduced particle sizes and increased transport efficiency of the coal slurries led to improved analytical recoveries of elements in the reference coal, SARM 18. The best analytical recoveries for all elements were achieved using 0.1% Triton X-100 with 10.0% DMF. Results obtained by ICP-OES after wet grinding of the coal with DMF, using 0.1% Triton X-100, also gave excellent recoveries (Al, 100%; Ca, 103%; Cr, 106%; Fe, 102%; Mg, 100%; Mn, 104%; Ni, 109%; Si, 102%; Ti, 95.0%; and V, 108%). The results obtained with 10.0% DMF and 0.1% Triton X-100 were in agreement with certified values for all selected elements according to paired t-test at the 95.0% confidence level. Selected elements (Al, Ca, Fe, Mg, Mn, Si, Ti and V) were also analysed with X-ray fluorescence for comparison with results obtained from ICP-OES. Analysis by ICP-OES of microwave digested coal was also carried out. It is suggested that the DMF slurry technique could be used for routine analysis of bituminous coals. 27 refs., 4 figs., 4 tabs.

Charge determination of nuclei with the AMS-02 silicon tracker

CERN Document Server

Alpat, B; Azzarello, P; Battiston, R; Bene, P; Bertucci, B; Bizzaglia, S; Bizzarri, M; Blasko, S; Bourquin, M; Bouvier, P; Burger, W J; Capell, M; Cecchi, C; Chang, Y H; Cortina, E; Dinu, N; Esposito, G; Fiandrini, E; Haas, D; Hakobyan, H; Ionica, M; Ionica, R; Kounine, A; Koutsenko, V F; Lebedev, A; Lechanoine-Leluc, C; Lin, C H; Masciocchi, F; Menichelli, M; Natale, S; Paniccia, M; Papi, A; Pauluzzi, M; Perrin, E; Pohl, M; Rapin, D; Richeux, J P; Wallraff, W; Willenbrock, M; Zuccon, P

2005-01-01

The silicon tracker of the AMS-02 detector measures the trajectory in three dimensions of electrons, protons and nuclei to high precision in a dipole magnetic field and thus measures their rigidity (momentum over charge) and the sign of their charge. In addition, it measures the specific energy loss of charged particles to determine the charge magnitude. Ladders from the AMS-02 tracker have been exposed to ion beams at CERN and GSI to study their response to nuclei from helium up to the iron group. The longest ladder, 72 multiplied by 496mm2, verified in the tests contains 12 sensors. Good charge resolution is observed up to iron.

Hyperfine fields of Fe in Nd2Fe14BandSm2Fe17N3

Science.gov (United States)

Akai, Hisazumi; Ogura, Masako

2015-03-01

High saturation magnetization of rare-earth magnets originates from Fe and the strong magnetic anisotropy stems from f-states of rare-earth elements such as Nd and Sm. Therefore the hyperfine fields of both Fe and rare-earth provide us with important pieces of information: Fe NMR enable us to detect site dependence of the local magnetic moment and magnetic anisotropy (Fe sites also contribute to the magnetic anisotropy) while rare-earth NQR directly give the information of electric field gradients (EFG) that are related to the shape of the f-electron cloud as well as the EFG produced by ligands. In this study we focus on the hyperfine fields of materials used as permanent magnets, Nd2Fe14BandSm2Fe17N3 from theoretical points of view. The detailed electronic structure together with the hyperfine interactions are discussed on the basis of the first-principles calculation. In particular, the relations between the observed hyperfine fields and the magnetic properties are studies in detail. The effects of doping of those materials by other elements such as Dy and the effects of N adding in Sm2Fe17N3 will be discussed. This work was supported by Elements Strategy Initiative Center for Magnetic Materials Project, the Ministry of Education, Culture, Sports, Science and Technology, Japan.

(C2N2H10)[Fe xV1-x(HPO3)F3] (x = 0.44, 0.72): Two new organically templated phosphites

International Nuclear Information System (INIS)

Cisneros, Jose L.; Fernandez-Armas, Sergio; Mesa, Jose L.; Pizarro, Jose L.; Arriortua, Maria I.; Rojo, Teofilo

2006-01-01

(C 2 N 2 H 10 )[Fe x V 1-x (HPO 3 )F 3 ] (x = 0.44, 0.72) have been synthesized using mild solvothermal conditions under autogenous pressure and the ethylenediamine molecule as templating agent. The crystal structures have been determined from X-ray single-crystal diffraction data. The compounds crystallize in the orthorhombic P2 1 2 1 2 1 space group with Z = 4 and unit-cell parameters a = 12.8494(9), b = 9.5430(6), c = 6.4372(5) A, and a = 12.8578(1), b = 9.5342(1), c = 6.4370(7) A for (C 2 N 2 H 10 )[Fe 0.44 V 0.56 (HPO 3 )F 3 ] and (C 2 N 2 H 10 )[Fe 0.72 V 0.28 (HPO 3 )F 3 ] (1) and (2), respectively. These isostructural compounds exhibit a monodimensional crystal structure formed by pillared double anionic chains with the formula [M(HPO 3 )F 3 ] 2- , extended along the [0 0 1] direction. These doubled ionic chains are the result of the linking of two simple chains in which there are alternating octahedral [MO 3 F 3 ] and tetrahedral groups [HPO 3 ]. The ethylendiammonium cations are placed in the space delimited by three different chains. The metallic ions are interconnected by the pseudo-pyramidal (HPO 3 ) 2- phosphite oxoanions, adopting a slightly distorted octahedral geometry. The IR spectra show bands corresponding to the phosphite oxoanion and the ethylendiamonium cation at 2400 and 1600 cm -1 , respectively. The thermogravimetric analyses show that these phases are stable up to ca. 280 deg. C, at higher temperatures, the decomposition of the crystal structure begins by calcination of the organic cation and the elimination of the fluoride anions. The diffuse reflectance spectra show bands of the V 3+ ion (d 2 ) in octahedral symmetry. The values of the Dq (1540, 1540 cm -1 ), and Racah parameters, B (560, 535 cm -1 ) and C (3055, 3140 cm -1 ) for (1) and (2), respectively, correspond with those usually found for octahedrically coordinated V(III) compounds. Magnetic measurements, performed on a powered sample from 5.0 to 300 K at 1000 G, in the ZFC and

Type test of the Rados MTS-N thermoluminescent dosimetry system for individual monitoring of whole body photons in HP (10)

International Nuclear Information System (INIS)

Ferreira, M.S.; Silva, E.R. da; Maurício, C.L.P.

2017-01-01

The Institute of Radioprotection and Dosimetry (IRD/CNEN-RJ), uses an automatic thermoluminescent dosimetry (TL) system for evaluation of whole body for photons with individual monitors RADOS MTS-N, with TLF detector of LiF: Mg, Ti. The objective of this work was to characterize this system for the evaluation of H P (10) operating magnitude. The measuring range is 0.2 mSv to 2 Sv, for photon energies from 20 keV to 1250 keV. Performance tests were done for the following characteristics: homogeneity of the monitors, system reproducibility, linearity, temperature and humidity effect, energy and angular dependence and fading. The acceptance requirements used to test system performance have been drawn from national and international documents. The results obtained prove that the system can be used to measure the occupational dose of photons in H P (10)

Impact of ultrafast demagnetization process on magnetization reversal in L10 FePt revealed using double laser pulse excitation

Science.gov (United States)

Shi, J. Y.; Tang, M.; Zhang, Z.; Ma, L.; Sun, L.; Zhou, C.; Hu, X. F.; Zheng, Z.; Shen, L. Q.; Zhou, S. M.; Wu, Y. Z.; Chen, L. Y.; Zhao, H. B.

2018-02-01

Ultrafast laser induced magnetization reversal in L10 FePt films with high perpendicular magnetic anisotropy was investigated using single- and double-pulse excitations. Single-pulse excitation beyond 10 mJ cm-2 caused magnetization (M) reversal at the applied fields much smaller than the static coercivity of the films. For double-pulse excitation, both coercivity reduction and reversal percentage showed a rapid and large decrease with the increasing time interval (Δt) of the two pulses in the range of 0-2 ps. In this Δt range, the maximum demagnetization (ΔMp) was also strongly attenuated, whereas the integrated demagnetization signals over more than 10 ps, corresponding to the average lattice heat effect, showed little change. These results indicate that laser induced M reversal in FePt films critically relies on ΔMp. Because ΔMp is determined by spin temperature, which is higher than lattice temperature, utilizing an ultrafast laser instead of a continuous-wave laser in laser-assisted M reversal may reduce the overall deposited energy and increase the speed of recording. The effective control of M reversal by slightly tuning the time delay of two laser pulses may also be useful for ultrafast spin manipulation.

First principles calculations of the magnetic and hyperfine properties of Fe/N/Fe and Fe/O/Fe multilayers in the ground state of cohesive energy

Science.gov (United States)

dos Santos, A. V.; Samudio Pérez, C. A.; Muenchen, D.; Anibele, T. P.

2015-01-01

The ground state properties of Fe/N/Fe and Fe/O/Fe multilayers were investigated using the first principles calculations. The calculations were performed using the Linearized Augmented Plane Wave (LAPW) method implemented in the Wien2k code. A supercell consisting of one layer of nitride (or oxide) between two layers of Fe in the bcc structure was used to model the structure of the multilayer. The research in new materials also stimulated theoretical and experimental studies of iron-based nitrides due to their variety of structural and magnetic properties for the potential applications as in high strength steels and for high corrosion resistance. It is obvious from many reports that magnetic iron nitrides such as γ-Fe4N and α-Fe16N2 have interesting magnetic properties, among these a high magnetisation saturation and a high density crimp. However, although Fe-N films and multilayers have many potential applications, they can be produced in many ways and are being extensively studied from the theoretical point of view there is no detailed knowledge of their electronic structure. Clearly, efforts to understand the influence of the nitrogen atoms on the entire electronic structure are needed as to correctly interpret the observed changes in the magnetic properties when going from Fe-N bulk compounds to multilayer structures. Nevertheless, the N atoms are not solely responsible for electronics alterations in solid compounds. Theoretical results showed that Fe4X bulk compounds, where X is a variable atom with increasing atomic number (Z), the nature of bonding between X and adjacent Fe atoms changes from more covalent to more ionic and the magnetic moments of Fe also increase for Z=7, i.e. N. This is an indicative that atoms with a Z number higher than 7, i.e., O, can produce several new alterations in the entire magnetic properties of Fe multilayers. This paper presents the first results of an ab-initio electronic structure calculations, performed for Fe-N and Fe

Deep conditions of hydrothermalism of dorsal East Pacific at 130N

International Nuclear Information System (INIS)

Boulegue, J.; Jedwab, J.

1985-01-01

Taking advantage of the formation of carbon graphite and Fe-Zn spinels one can compute the conditions of sea water-basalt interaction in deep conditions at 13 0 N E.P.R. One finds: p=260-500 bar, T=440-480 0 C, fO 2 =10 -27 -10sup(-24.5) bar, pH 2 O/pH 2 approximately= 100, fCO 2 /fCO approximately= 600. These conditions lead to a discussion of the possibilities of vaporisation of the hydrothermal fluid and to a discussion of the geochemical behaviour of U and Fe [fr

Investigation of Fe-Si-N films as magnetic overcoat for high density recording disk drives

International Nuclear Information System (INIS)

Gauvin, M.; Talke, F. E.; Fullerton, E. E.

2010-01-01

A 50-nm-thick Fe-Si-N films were deposited via reactive magnetron cosputtering of independent Fe and Si targets, in Ar/N 2 gas mixture, under different dc Fe target power conditions. Magnetic properties, mechanical hardness and tribological properties were characterized as a function of the Fe target power by magnetometry, nanoindentation, and nanoscratch testing, respectively. Deposited samples were found to be ferromagnetic with a coercivity of approximately 20 Oe and a saturation magnetization increasing from 200 to 1100 emu/cm 3 as a function of Fe sputter power, i.e., values typical of soft magnetic materials. The mechanical hardness was found to be between 50% and 70% of the hardness of a pure SiN x film. Nanotribological properties of films deposited with a Fe target power ≥80 W degraded rapidly.

New method for simultaneous determination of 55Fe and 59Fe in blood serum samples

International Nuclear Information System (INIS)

Saukkonen, H.; Uhlenius, R.

1978-01-01

Routine methods for the measurement of 55 Fe and 59 Fe activities in biological samples are frequently required in metabolic studies of iron. A new simple method for the simultaneous determination of 59 Fe and 55 Fe concentration in 5 cm 3 samples of blood is described and carefully evaluated. Before the measurement of the activity, organic matter was eliminated by HNO 3 -HClO 4 wet ashing and iron was electroplated onto a copper plate. The accuracy of results was studied by assessing samples, which contained known amounts of radioactivity and determining the counts per nanocurie in each case. The accuracy of the results of 59 Fe and 55 Fe determinations was found to be about 5%. The method has been routinely used to determine iron resorption in patients using the double isotope method. The determination proved to be satisfactory and not too laborious. When performing the yield determination there is a way of detecting and correcting mistakes or incompleteness in different stages of the measurement, thus leading to a high degree of reliability. (T.G.)

Compilation of fastener testing data received in response to NRC Compliance Bulletin 87-02

International Nuclear Information System (INIS)

Cwalina, G.C.; Conway, J.T.; Parker, L.B.

1989-06-01

On November 6, 1987, the Nuclear Regulatory Commission (NRC) issued Bulletin 87-02, ''Fastener Testing to Determine Conformance With Applicable Material Specifications,'' to all holders of operating licenses or construction permits for nuclear power reactors (licensees). The bulletin was issued so that the NRC staff could gather data to determine whether counterfeit fasteners are a problem in the nuclear power industry. The bulletin requested nuclear power plant owners to determine whether fasteners obtained from suppliers and/or manufacturers for use in their facilities meet the mechanical and chemical specifications stipulated in the procurement documents. The licensees were requested to sample a minimum of 10 safety-related and 10 non-safety-related fasteners (studs, bolts, and/or cap screws) and a sample of typical nuts that would be used with each fastener and to report the testing results to the NRC. The results of this study did not indicate a safety concern relating to the use of mismarked or counterfeit fasteners in the nuclear industry, but they did indicate a nonconformance rate of 8 to 12 percent for fasteners. The NRC staff is considering taking action to improve the effectiveness of receipt inspection and testing programs for all materials at nuclear power plants

Growth and characterization of Fe nanostructures on GaN

International Nuclear Information System (INIS)

Honda, Yuya; Hayakawa, Satoko; Hasegawa, Shigehiko; Asahi, Hajime

2009-01-01

We have investigated the growth of Fe nanostructures on GaN(0 0 0 1) substrates at room temperature using reflection high-energy electron diffraction (RHEED), scanning tunneling microscopy (STM), and superconducting quantum interference device magnetometer. Initially, a ring RHEED pattern appears, indicating the growth of polycrystalline α-Fe. At around 0.5 nm deposition, the surface displays a transmission pattern from α-Fe films with the epitaxial relationship of Fe(1 1 0)//GaN(0 0 0 1) and Fe[1 -1 1]//GaN[1 1 -2 0] (Kurdjumov-Sachs (KS) orientational relationship). Further deposition to 1 nm results in the appearance of a new spot pattern together with the pattern from domains with the KS orientation relationship. The newly observed pattern shows that Fe layers are formed with the epitaxial relationship of Fe(1 1 0)//GaN(0 0 0 1) and Fe[0 0 1]//GaN[1 1 -2 0] (Nishiyama-Wasserman (NW) orientational relationship). From STM images for Fe layers with the KS and NW orientational relationships, it can be seen that Fe layers with the KS relationship consist of round-shaped Fe nanodots with below 7 nm in average diameter. These nanodots coalesce to form nanodots elongating along the Fe[1 0 0] direction, and they have the KS orientational relationship. Elongated Fe nanodots with the NW relationship show ferromagnetism while round-shaped Fe nanodots with the KS relationship show super-paramagnetic behavior. We will discuss their magnetic properties in connection with the change in crystalline configurations of nanodots.

Behavior of methyl orange and orange 10 (orange G) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe

International Nuclear Information System (INIS)

Cruz N, G.

2015-01-01

This work is focused on studying the sorption capacity of methyl orange dye (Nm) and orange 10 (N-10) in the presence of hydrotalcite type compounds of Mg/Al and Mg/Fe uncalcined and calcined previously at 500 degrees Celsius. Sorption isotherms were determined and the study of the kinetics of sorption was performed. The materials were characterized before and after sorption processes of these dyes by X-ray diffraction, scanning electron microscopy, the specific surface area determination by the Brunauer-Emmett-Teller method, thermogravimetry coupled to mass and infrared spectrometry. The hydrotalcite type compounds reported in this paper were prepared in the laboratory and their acronyms are: HTMgAlG1, HTMgAlMO, HTMgFeG1 and HTMgFeG2. Note that in this work the best conditions for preparing compounds of Mg/Fe were found. From patterns of X-ray diffraction was identified the typical crystal structure of the hydrotalcite type compounds. By scanning electron microscopy the morphology could be determined in the form of flakes characteristics of these compounds. Likewise with elemental analysis of energy dispersive X-ray spectroscopy the presence of Mg, Al, Fe and C, elements of interest for this study was determined. The compounds presented a specific surface area relatively high from 80 to 120 m 2 /g. Thermogravimetry results presented spectra of mass loss very characteristic associated to water losses, dehydroxylation and decarboxylation. The characteristic bands of water and carbonate were assigned by infrared spectroscopy and the bands corresponding to the dyes sulfonates were identified only for the calcined materials. The sorption capacities found of these compounds were as follows: for Nm in the compound HTMgAlG1 uncalcined was 17.82 mg/g for an initial concentration of 200 mg/L and for calcined (HTMgAlMOcal) of 99.8 mg/g with and initial concentration of 1000 mg/L. Moreover, the sorption capacity of the dye N-10 in this same material was 17.92 mg/g and 99.4 mg

Gaseous oxygen and hydrogen embrittlements of the uranium-10 weight % molybdenum alloy

International Nuclear Information System (INIS)

Corcos, Jean.

1979-07-01

The stress corrosion of an Uranium-10 weight % Molybdenum alloy in high purity gaseous oxygen and hydrogen was studied. Tests were performed with fracture-mechanic specimens, fatigue precracked and carried out in tension with a constant sustained load. The experimental procedure enabled to determine the S.C. morphology during the test, and its kinetics. Tests in gaseous oxygen were performed with p02=0.15 MPa from 0 0 C to 100 0 C, and at 20 0 C for p02=0.15, 0.15.10 -2 and 0.15.10 -4 MPa. Two kinetic laws are proposed. Cracking is transgranular with a quasi-clivage type, and occurs on the (1 1 1) planes of the matrix. Tests in gaseous hydrogen were performed with pH2=0.15 MPa from - 50 0 C to + 135 0 C; for all the tests, even those under no exterior load, there is a failure by S.C. and macroscopic hydruration occurs. We propose a kinetic law, which may display that the hydruration phenomenon rules the S.C. propagation. We have performed the identification of the hydride, as well as the study of the precipitation. These phenomena don't occur with pH2=0.15.10 -2 MPa. The embrittlement is thought to be due to a formation-failure cycle of an hydride precipitate at the crack tip [fr

Synthesis and magnetic properties of PrFe11V1-xTix and their nitrides

International Nuclear Information System (INIS)

Tang, S.L.; Wang, B.W.; Zhang, C.; Jin, X.M.; Zhang, S.Y.; Du, Y.W.

1997-01-01

We have succeeded in synthesizing PrFe 11 V 1-x Ti x (x=0.2 1) compound and their nitrides with the ThMn 12 -type structure. The phase formation and magnetic properties have been investigated by x-ray diffraction, differential thermometric analysis, and magnetic measurement. The stable temperature range of the 1-12 phase for PrFe 11 V 1-x Ti x alloys has been determined as a function of Ti content. PrFe 11 V compounds with the ThMn 12 -type structure do not exist and PrFe 11 Ti compounds with the TnMn 12 -type structure are obtained by annealing in a narrow temperature range between 1303 and 1383 K. Furthermore, 1-12 phase with the ThMn 12 -type structure can be obtained at lower temperature and wider temperature range with decreasing Ti content x (0.2≤x≤1). PrFe 11 V 1-x Ti x N y with x=0.2 1 has a T c of about 730 785 K, B a larger than 8 T and M s in the range 144 148 emu/g. These intrinsic magnetic properties are highly favorable for permanent magnet applications. As a preliminary, an intrinsic coercivity of 5.4 kOe is obtained for PrFe 11 V 0.5 Ti 0.5 N y at room temperature by using mechanical alloying technique. copyright 1997 American Institute of Physics

Moessbauer and X-ray Study of Fe1-xAlx, 0.2≤x≤0.5, Samples Produced by Mechanical Alloying

International Nuclear Information System (INIS)

Oyola Lozano, D.; MartInez, Y. Rojas; Bustos, H.; Perez Alcazar, G. A.

2004-01-01

In this work we report the magnetic and structural properties obtained by Moessbauer spectroscopy and X-ray diffraction, of the Fe 1-x Al x , 0.2≤x≤0.5, alloys produced by mechanical alloying. Alloys with x=0.2, 0.3, 0.4 and 0.5, were for milled 12, 24, 36, and 48 hours. All the obtained alloys are in the bcc phase. The obtained Moessbauer spectra are characteristic of disordered ferromagnetic system. The lattice parameter remains nearly constant (∼2.91 A) for all the milling times and compositions. The mean grain sizes in the (110) and (211) direction are nearly constants with the milling time but vary from 15.5 to 11 nm and from 10.5 to 8.5 nm when Al content grow between x=0.2 to x=0.4, respectively. The difference between the mean grain sizes in these two directions shows that the grains are of prolate spheroid form.

N-m-nitrocinnamoylphenylhydroxyl-amine as reagent for amperometric determination of yttrium

International Nuclear Information System (INIS)

Oliferenko, G.L.; Gallaj, Z.A.; Sheina, N.M.; Shvedene, N.V.

1983-01-01

Possibility of using organic reagent of unsaturated N-arylsubstituted derivatives class of hydroxamic acids N-m-nitrocinnamoyl phenylhydroxylamire (NCPHA) for amperometric titration of yttrium using indication of e.t.p. by current of reagent oxidation on graphite electrode is investigated. Metal and the NCPHA form difficultly soluble complex with ratio of yttrium to the NCPHA, which is equal to 1:3. Buffer mixtures of 0.1MNH 3 +0.1MCH 3 COOH composis tion with pH 6.3-7.5 are optimal background solutions for amperometric titration of yttrium. The proposed method permits to determine 10-600 μkg of yttrium in the volume of 10 ml. Effect of the series of strange elements on titration of yttrium with NCPHA (Ca, Mg, Mn (2), Al, CU (2), Fe (3) REE and others) is studied. The developed method is used for yttrium determination in luminophores of Casub(n)-- Ysub(m)Fsub(z)xMn(2) (1-10%) composition

Seven pin bundle fast top tests L01 and L02

International Nuclear Information System (INIS)

Davies, A.L.; Bowen, G.R.; Herbert, R.; Kear, K.L.; Tylka, J.P.; Holland, J.W.

1984-01-01

Tests L01 and L02 were the first two seven pin bundle tests in the PFR/TREAT program of fuel failure tests carried out jointly by the US and the UK. The two tests were on bottom plenum annular pellet mixed oxide fuel clad in 316 stainless steel. L01 used fresh fuel, while L02 used PFR irradiated 4% burn-up fuel, to determine any differences in the failure mechanism and subsequent fuel behavior due to irradiation. They were performed in flowing sodium in the Mark IIIA version of a TREAT integral loop. Both were fast transient overpower (TOP) tests intended to simulate 5 $/s reactivity ramp hypothetical accidents in a large fast reactor. The test objectives were to obtain information on fuel motion in the central hole before failure, the time and location of cladding failures, and material motion in the channel after failure, having particular regard to the effect of irradiation

Flow injection spectrophotometric determination of Fe(III) and V(v)

International Nuclear Information System (INIS)

Elrahman, Azza Mohamed

2000-01-01

Phenylflourone was synthesized with the objective of developing a method for determining Fe(III) and V(V) in the pressence of micelles using flow injectoin technique. Phenylflourone showed a wavelength of maximum absorption at 412 nm which was not affected by the presence of miccelles i.e. n-hexadodecylpyridinum bromide and sodium n-dodecylsulphate, but they have different effects on the absorbance of PHF. The example of PHF-Fe(III) and PHF-V(V) showed the wavelength of the maximum absorption at 4428 nm and 412 nm, respectively. Presence of micelles shifted the wavelength of the two complexes to a lower one. Generally the addition of micelles increased the absorbance of phenylflourone metal ions complexes except for PHF-V(V) with hexadodecylpyridinum bromide. With flow injection technique two approaches were practiced the use of micelle as a carrier or water as a carrier. Sodium n-dodecylsulphate increased the absorbance of the two complexes when it was used as a carrier or added to the metal ions using water as carrier. On the other hand, the use of n-hexadodecylpyridinum bromide as carrieer increased the absorbance of the complexes but it decreased the absorbance when it was used in conjunction with metal ions and water as a carrier. After establishing the optimum FI conditions for PHF-Fe(III) and PHF-V(V) complexes, the calibration curves were construction and produced semiliner response in the concentration range studied. Ti(IV) III, Mo(VI) showed a positive interference in PHF-Fe(III) and PHF-V(V) complexes, respectively.(Author)

Coercivity Recovery Effect of Sm-Fe-Cu-Al Alloy on Sm2Fe17N3 Magnet

Science.gov (United States)

Otogawa, Kohei; Asahi, Toru; Jinno, Miho; Yamaguchi, Wataru; Takagi, Kenta; Kwon, Hansang

2018-03-01

The potential of a Sm-Fe-Cu-Al binder for improvement of the magnetic properties of Sm2Fe17N3 was examined. Transmission electron microscope (TEM) observation of a Sm-Fe-Cu-Al alloy-bonded Sm2Fe17N3 magnet which showed high coercivity revealed that the Sm-Fe-Cu-Al alloy had an effect of removing the surface oxide layer of the Sm2 Fe17N3 grains. However, the Sm-Fe-Cu-Al binder was contaminated by carbon and nitrogen, which originated from the organic solvent used as the milling medium during pulverization. To prevent carbon and nitrogen contamination, the Sm-Fe- Cu-Al alloy was added directly on the surface of the Sm2Fe17N3 grains by sputtering. Comparing the recovered coercivity per unit amount of the added binder the uncontaminated binder-coated sample had a higher coercivity recovery effect than the milled binder-added sample. These results suggested that sufficient addition of the contamination-free Sm-Fe-Cu-Al binder has the possibility to reduce the amount of binder necessary to produce a high coercive Sm2Fe17N3 magnet.

Electrochemical characterization of La0.6Ca0.4Fe0.8Ni0.2O3 cathode on Ce0.8Gd0.2O1.9 electrolyte for IT-SOFC

DEFF Research Database (Denmark)

Ortiz-Vitoriano, N.; Bernuy-Lopez, C.; Hauch, Anne

2014-01-01

For Solid Oxide Fuel Cells (SOFCs) to become an economically attractive energy conversion technology, suitable materials and structures which enable operation at lower temperatures, while retaining high cell performance, must be developed. Recently, the perovskitetype La0.6Ca0.4Fe0.8Ni0.2O3 oxide...... has shown potential as an intermediate temperature SOFC cathode. An equivalent circuit describing the cathode polarization resistances was constructed from analyzing impedance spectra recorded at different temperatures in oxygen. A competitive electrode polarization resistance is reported...... for this oxygen electrode using a Ce0.8Gd0.2O1.9 electrolyte, determined by impedance spectroscopy studies of symmetrical cells sintered at 800 _C and 1000 _C. Scanning electron microscopy (SEM) studies of the symmetrical cells revealed the absence of any reaction layer between cathode and electrolyte...

Synthesis, thermodynamic and transport properties of the compounds Sr3FeMO7-δ(M = Fe, Ni) in the temperature range of 400≤T≤1000oC

International Nuclear Information System (INIS)

Mogni, L; Prado, E; Caneiro, A

2004-01-01

The synthesis is presented for the mixed conductors Sr 3 FeMO 7-δ (M = Fe, Ni) belonging to the Ruddlesden Popper series A n+1 B n O3 n+1 with n = 2 using the acetates method. The samples were characterized using X-ray diffraction techniques, scanning electron microscopy and EDS. The variation of the chemical potential of oxygen was determined with the oxygen content of these compounds (7-δ) in a wide range of partial oxygen pressure 10 -5 ≤pO2≤ 1 atm and temperatures (673-1273 K). The electrical conductivity as a function of the temperature and the pO2 were measured by the four points method. Based on an analysis of the test data the effect of the cationic substitution of Fe by Ni on the thermodynamic, structural properties and on the structure of defects in the temperature range of interest for the electrochemical devices is discussed (WC)

Features of the structural and magnetic properties of Pb(TixZr1–xO3-NiFe1.98Co0.02O4 in the polarized state

Directory of Open Access Journals (Sweden)

Baev Vadim

2017-06-01

Full Text Available Composites with a 90%Pb(TixZr1-xO3-10%NiFe1.98Co0.02O4 composition have been synthesized. It has been established that the polarization of samples resulting from exposure to an electric field for 1 hour of 4 kV/mm in strength at a temperature of 400 K leads to crystal structure deformation. The compression of elementary crystal cells in some areas during polarization of the sample creates conditions suitable for the enhancement of magnetic exchange interactions. It has been found that the polarization process of such compositions leads to increases in specific magnetization and magnetic susceptibility. The analysis of Mössbauer spectra has shown that the polarization of the 90%Pb(TixZr1-xO3-10%NiFe1.98Co0.02O4 composite leads to significant changes in the effective magnetic fields of iron subspectra in various positions.

In situ X-ray and neutron diffraction of the Ruddlesden–Popper compounds (RE2−xSrx)0.98(Fe0.8Co0.2)1−yMgyO4−δ (RE=La, Pr): Structure and CO2 stability

International Nuclear Information System (INIS)

Chatzichristodoulou, C.; Hauback, B.C.; Hendriksen, P.V.

2013-01-01

The crystal structure of the Ruddlesden–Popper compounds (La 1.0 Sr 1.0 ) 0.98 Fe 0.8 Co 0.2 O 4−δ and (La 1.2 Sr 0.8 ) 0.98 (Fe 0.8 Co 0.2 ) 0.8 Mg 0.2 O 4−δ was investigated at 1000 °C in N 2 (a O2 =1×10 −4 ) by in-situ powder neutron diffraction. In-situ powder X-ray diffraction (PXD) was also employed to investigate the temperature dependence of the lattice parameters of the compounds in air and the oxygen activity dependence of the lattice parameters at 800 °C and 1000 °C. The thermal and chemical expansion coefficients, determined along the two crystallographic directions of the tetragonal unit cell, are highly anisotropic. The equivalent pseudo-cubic thermal and chemical expansion coefficients are in agreement with values determined by dilatometry. The chemical stability in CO 2 containing environments of various Ruddlesden–Popper compounds with chemical formula (RE 2−x Sr x ) 0.98 (Fe 0.8 Co 0.2 ) 1−y Mg y O 4−δ (RE=La, Pr), as well as their stability limit in H 2 /H 2 O=4.5 were also determined by in-situ PXD for x=0.9, 1.0 and y=0, 0.2. - Graphical abstract: Influence of electronic configuration on bond length, lattice parameters and anisotropic thermal and chemical expansion. Highlights: ► The thermal and chemical expansion coefficients are largely anisotropic. ► The expansion of the perovskite layers is constrained along the a direction. ► The studied compositions show remarkable thermodynamic stability upon reduction. ► The thermal and chemical expansion coefficients are lower than related perovskites. ► The investigated materials decompose in CO 2 containing atmospheres

Structural and magnetic properties of Fe{sub 7−n}Pt{sub n} with n = 0, 1, 2, . . . 7, bimetallic clusters

Energy Technology Data Exchange (ETDEWEB)

Ponce-Tadeo, A. P.; Morán-López, J. L., E-mail: joseluis.moran@ipicyt.edu.mx [Instituto Potosino de Investigación Científica y Tenológica, División de Materiales Avanzados (Mexico); Ricardo-Chavez, J. L. [Benemérita Universidad Autónoma de Puebla, Laboratorio Nacional de Supercómputo (Mexico)

2016-11-15

An exhaustive study of the structural and magnetic properties of Fe{sub 7−n}Pt{sub n} with n = 0, 1, 2, …7, bimetallic clusters is presented. Based on ab initio density functional theory that includes spin-orbit coupling (SOC) and graph theory, the ground state geometry, the local chemical order, and the orbital and spin magnetic moments are calculated. We show how the systems evolves from the 3-d Fe to the quasi-planar Pt clusters. These calculations show that SOC are necessary to describe correctly the composition dependence of the binding energy of these nanoalloys. We observe that the ground state geometries on the Fe rich side resemble the fcc structure adopted by bulk samples. Furthermore, we observe how the spin and orbital magnetic moments depend on the chemical concentration and chemical order. Based on these results, we estimated the magnetic anisotropy energy and found that the largest values correspond to some of the most symmetric structures, Fe{sub 5}Pt{sub 2} and FePt{sub 6}. To determine the degree of non-collinearity, we define an index that shows that in FePt{sub 6} the total magnetic moments, on each atom, are the less collinear.

[Determination of 10-hydroxy-2-decenoic acid (10-HDA) in Chinese traditional medicine preparations by high performance liquid chromatography].

Science.gov (United States)

Yang, J; Chen, L

1998-03-01

This paper reports the quantitative determination of 10-HDA in Chinese traditional medicine preparations by HPLC. Spherisorb C18 column was used. The mobile phase consisted of methanol-distilled water and phosphoric acid(45:55:0.5, V/V). The elute was monitored at 210 nm. The good linearity was shown between the concentration of 10-HDA and peak area in the concentration range of 6.0-30.0 mg/L (r = 0.9999, n = 5). The detection limit was 0.2 mg/L (S:N = 3:1). The within-day and between-day RSD were 2.1%-2.2% and 2.9%-4.0%, respectively. Peaks of 10-HDA and impurities in these samples were separated completely. This method is simple, sensitive and accurate.

Cacotheline as an oxidimetric reagent. Determination of Sn(II), Cu(I), Ti(III), Fe(II), V(II) and V(III)

International Nuclear Information System (INIS)

Nemani Murty, K.; Yedluri Rao, P.; Geddada Chalam, K.

1982-01-01

Sn(II), Ti(III), Cu(I),Fe(II), V(III) and V(II) can be titrated potentiometrically with cacotheline in 1-4 M hydrochloric acid, 0.5-2 M hydrochloric acid, 0.5-1.5 M sulphuric acid in presence of 4 ml of 10% EDTA solution in a total volume of 50 ml, 9-10 M phosphoric acid, 4-8 M acetic acid and 3-8 M acetic acid respectively. Cacotheline can be used for the assay of tin plate and solder. The cacotheline undergoes a 2-electron reduction reaction. A cacotheline solution (0.005 M) in 0.02 M hydrochloric acid is fairly stable for several months. The conditional redox potentials of cacotheline have been determined in sulphuric, phosphoric and acetic acid medium. (Author)

Structures, stability, magnetic moments and growth strategies of the Fe{sub n}N (n = 1–7) clusters: All-electron density functional theory calculations

Energy Technology Data Exchange (ETDEWEB)

Li, Zhi, E-mail: lizhi81723700@163.com [School of Materials and Metallurgy, University of Science and Technology Liaoning, Anshan, 114051 (China); Zhao, Zhen [School of Chemistry and Life Science, Anshan Normal University, Anshan, 114007 (China)

2017-02-01

The geometries, electronic properties, magnetic moments and growth strategies of the Fe{sub n}N (n = 1–7) clusters are investigated using all-electron density functional theory. The results show that N doping significantly distorts the Fe{sub n} clusters. Fe{sub 4}N and Fe{sub 6}N clusters are more stable structures than other considered Fe{sub n}N clusters. Local peaks of HOMO-LUMO gap curve are found at n = 3, 7, implying that the chemical stability of the Fe{sub 3}N and Fe{sub 7}N clusters is higher. Fe{sub 2}N, Fe{sub 4}N and Fe{sub 6}N clusters have larger magnetic moments compared to other considered Fe{sub n}N (n = 1–7) clusters. It can be seen that the Fe{sub 5} clusters are easier to adsorb a Fe atom while the Fe{sub 4} clusters are easier to adsorb a N atom. The considered Fe{sub m}N clusters prefer to adsorb a Fe atom and larger Fe{sub m}N clusters are easier to grow. - Highlights: • The structural stability of the Fe{sub 4}N and Fe{sub 6}N clusters is higher. • The chemical stability of the Fe{sub 3}N and Fe{sub 7}N clusters is higher. • Fe{sub 5} clusters are easier to adsorb a Fe atom while Fe{sub 4} clusters are easier to adsorb a N atom. • Fe{sub n}N clusters prefer to adsorb a Fe atom.

A first principles calculations of structural, electronic, magnetic and dynamical properties of mononitrides FeN and CoN

International Nuclear Information System (INIS)

Soni, Himadri R.; Mankad, Venu; Gupta, Sanjeev K.; Jha, Prafulla K.

2012-01-01

Highlights: ► We present spin dependent bandstructure, structural and magnetic moment of FeN/CoN. ► The PDC, PHDOS, spin effect on phonons suggests ZB is preferred at ambient pressure. ► Spin calculation offers an opportunity to understand the role of spin on phonons. - Abstract: Using first principles density functional theoretical calculations, the present paper reports a systematic nonspin and spin polarized total energy calculations of the lattice dynamical and a number of other properties such as band structure, structural and magnetic moment of two mononitrides FeN and CoN. The phonon dispersion curves and phonon density of states in the case of FeN and CoN have been determined for the first time and discussed. The structural and dynamical calculations suggest that the zinc blende structure is preferred at ambient pressure for both compounds. The rocksalt FeN has a nonzero magnetic moment while for FeN in zinc blende phase, it is either zero or very small. The zinc blende phase for both compounds is nonmagnetic. The spin calculation offers an intensive opportunity to understand the role of spin on the phonon properties of two mononitrides. Majority of the modes are sensitive to the effect of spin due to the modification of lattice constant. In this work we reveal that spin modifies the interionic interactions and local structure and leads to a flexible lattice which can be used for the functional materials design.

Structural phase transition and multiferroic properties of Bi0.8A0.2Fe0.8Mn0.2O3 (A = Ca, Sr)

Science.gov (United States)

Rout, Jyoshna; Choudhary, R. N. P.

2018-05-01

The multiferroic BiFeO3 and Bi0.8A0.2Fe0.8Mn0.2O3 (A = Ca, Sr) have been synthesized using direct mechanosynthesis. Detailed investigations were made on the influence of Ca-Mn and Sr-Mn co-substitutions on the structure change, electric and magnetic properties of the BFO. Rietveld refinement on the XRD pattern of the modified samples clarifies the structural transition from R3c:H (parent BiFeO3) to the biphasic structure (R3c: H + Pnma). Scanning electron micrographs confirmed the polycrystalline nature of the materials and each of the microstructure comprised of uniformly distributed grains with less porosity. The dielectric measurements reveal that enhancement in dielectric properties due to the reduction of oxygen vacancies by substitutional ions. Studies of frequency-dependence of impedance and related parameters exhibit that the electrical properties of the materials are strongly dependent on temperature, and bear a good correlation with its microstructure. The bulk resistance (evaluated from impedance studies) is found to decrease with increasing temperature for all the samples. The alternating current (ac) conductivity spectra show a typical signature of an ionic conducting system, and are found to obey Jonscher's universal power law. Preliminary studies of magnetic characteristics of the samples reveal enhanced magnetization for Ca-Mn co-substituted sample. The magnetoelectric coefficient as the function of applied dc magnetizing field under fixed ac magnetic field 15.368 Oe is measured and this ME coefficient αME corresponds to induction of polarization by a magnetic field.

Evaluación por rendimiento de 12 genotipos promisorios de fríjol voluble (Phaseolus vulgaris L. tipo Bola roja y Reventón para las zonas frías de Colombia

Directory of Open Access Journals (Sweden)

López Jesús Edgardo

2006-12-01

Full Text Available

10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville;">El fríjol común (10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville-Italic; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville-Italic;">Phaseolus vulgaris 10.0pt; font-family: ";Cambria";,";serif";; mso-ascii-theme-font: major-latin; mso-fareast-font-family: Baskerville; mso-hansi-theme-font: major-latin; mso-bidi-font-family: Baskerville;">L. es un alimento básico en la región Andina por ser una fuente rica en proteína y de bajo costo. La investigación para incrementar rendimientos en esta leguminosa es una opción para mejorar la competitividad en el mercado mundial. El objetivo principal de este trabajo fue evaluar por rendimiento los genotipos promisorios de fríjol voluble, tipos Bola roja y Reventón, para las zonas frías de Colombia mediante el análisis de sendero. Se realizó un diseño de bloques completos al azar con tres réplicas para evaluar 10 genotipos promisorios de fríjol voluble. El análisis de sendero para el rendimiento por planta y las correlaciones entre el rendimiento y sus componentes mostraron que el carácter número de vainas por planta es el de mayor importancia sobre la determinación del rendimiento, en comparación con los caracteres peso de 100 semillas y número de semillas por vaina, tanto en los genotipos de fríjol voluble tipo Bola roja como tipo Reventón. 

Spectrophotometric determination of Fe(II) in Geological Materials by Using Ferrozine as Cromogenic Reagent

International Nuclear Information System (INIS)

Sanchez, D. M.; Martin, R.; Marin, J.; Morante, R.; Gutierrez, L.; Bayon, A.

1999-12-01

A rapid and sensitive spectrophotometric method for the determination of labile ferrous iron in geological materials is described. Samples are treated by boiling with hydrochloric acid for 60 min. in an atmosphere of carbon dioxide. Systematic erroneous results due to high concentrations of ferric iron are resolved. The limit of detection for the method was 0.02% of FeO. International standard granites analysed by the proposed method showed recoveries ranged from 81-102%. (Author) 9 refs

The dependence of activity coefficient on intensive thermodynamic parameters in a liquid Fe-N-V alloy

Energy Technology Data Exchange (ETDEWEB)

Hutny, A.; Siwka, J. [Faculty of Materials Processing Technology and Applied Physics, Technical Univ. of Czestochowa (Poland)

2003-07-01

The article presents the methodology and results of experimental studies on the solubility of nitrogen in liquid Fe-V alloys. Tests were carried out using the levitation metal melting technique. Liquid alloys of Fe-V ([%V]{sub wt.%} 1.5; 2.5; 4,0; 5.8; 7.8; 12.2; 45%) were saturated with nitrogen at temperatures of 2073, 2173, 2273 K. The partial pressure of nitrogen was varied in the range 0.001-2.5 MPa. The experiment involved melting a 1 g specimen in an electromagnetic field generated by a levitation coil, filling the reaction chamber with nitrogen up to the required pressure and heating the specimen up to a preset temperature. High nitrogen concentrations were obtained in the samples due to the formation of high nitrogen partial pressures in the gaseous phase in the reaction chamber. In such conditions, all interactions of nitrogen in the alloy tested could be disclosed, namely: nitrogen-vanadium, nitrogen-nitrogen, and nitrogen-nitrogen-vanadium interactions. The results of the tests showed a nonlinear dependence of the activity coefficient, f{sub N}, not only on vanadium content in the alloy, but also on nitrogen content in it. Using the experimental data and the findings of the previous study on the liquid Fe-N alloy, temperature relationships of inter- and self-reaction parameters have been determined. (orig.)

Phase Transformations and Phase Equilibria in the Fe-N System at Temperatures below 573 K

DEFF Research Database (Denmark)

Malinov, S.; Böttger, A.J.; Mittemeijer, E.J.

2001-01-01

The phase transformations of homogeneous Fe-N alloys of nitrogen contents from 10 to 26 at. pct were investigated by means of X-ray diffraction analysis upon aging in the temperature range from 373 to 473 K. It was found that precipitation of alpha double prime-Fe16N2 below 443 K does not only oc...

Characterization of the phase composition, crystal structure and superconducting properties of Fe{sub 1.02}Se{sub y}Te{sub 1−y−x}S{sub x}

Energy Technology Data Exchange (ETDEWEB)

Abouhaswa, A.S., E-mail: aliabohaswa@hotmail.com [Institute of Natural Sciences, Ural Federal University, 620083, Ekaterinburg (Russian Federation); Merentsov, A.I. [Institute of Natural Sciences, Ural Federal University, 620083, Ekaterinburg (Russian Federation); Baranov, N.V. [Institute of Natural Sciences, Ural Federal University, 620083, Ekaterinburg (Russian Federation); M.N. Miheev Institute of Metal Physics, Ural Branch of RAS, 620990, Ekaterinburg (Russian Federation)

2016-08-15

Highlights: • The Fe{sub 1.02}Se{sub 0.5}Te{sub 0.5−x}S{sub x} and Fe{sub 1.02}Se{sub 0.4}Te{sub 0.6−x}S{sub x} samples have been synthesized. • The S for Te substitution results in a small expansion of the crystal lattice of the PbO-type phase. • This expansion is attributed to changes in the phase relation and chemical composition of phases. • There is a correlation between the changes of T{sub c} and lattice parameters of the PbO-type phase. - Abstract: Two series of the Fe{sub 1.02}Se{sub 0.5}Te{sub 0.5–x}S{sub x} (I) and Fe{sub 1.02}Se{sub 0.4}Te{sub 0.6–x}S{sub x} (II) samples with the sulfur for tellurium substitution and with the invariable Se concentrations have been synthesized and studied by means of X-ray diffraction, scanning electron microscopy, electrical resistivity and magnetic susceptibility measurements. The superconducting PbO-type phase is found to persists in the first series up to x = 0.4 and in the second one up to x = 0.5. Despite the lower ionic radius of sulfur in comparison with tellurium the replacement of tellurium by sulfur does not lead to contraction of the unit cell volume of the superconducting phase in both I and II series with ternary mixture of chalcogens. Variations of the lattice parameters caused by the S for Te substitution in the Fe{sub 1.02}Se{sub 0.5}Te{sub 0.5–x}S{sub x} and Fe{sub 1.02}Se{sub 0.4}Te{sub 0.6–x}S{sub x} samples are found to be less pronounced than that reported for the Fe{sub 1.02}Te{sub 0.5}Se{sub 0.5-x}S{sub x} system and are accompanied by lowering of the critical temperature. The behavior of the lattice parameters and critical temperature of Fe(S,Se,Te) materials with the ternary mixture of chalcogens at substitutions is ascribed to the changes in the volume fraction and chemical compositions of the coexisting tetragonal and hexagonal phases.

Ancient Chemistry "Pharaoh's Snakes" for Efficient Fe-/N-Doped Carbon Electrocatalysts.

Science.gov (United States)

Ren, Guangyuan; Gao, Liangliang; Teng, Chao; Li, Yunan; Yang, Hequn; Shui, Jianglan; Lu, Xianyong; Zhu, Ying; Dai, Liming

2018-04-04

The method of fabricating nonprecious metal electrocatalysts with high activity and durability through a facile and eco-friendly procedure is of great significance to the development of low-cost fuel cells and metal-air batteries. Herein, we present that an ancient chemical reaction of "Pharaoh's snakes" can be a fast and convenient technique to prepare Fe-/N-doped carbon (Fe/N-C) nanosheet/nanotube electrocatalysts with sugar, soda, melamine, and iron nitrate as precursors. The resultant Fe/N-C catalyst has a hierarchically porous structure, a large surface area, and uniformly distributed active sites. The catalyst shows high electrocatalytic activities toward both the oxygen reduction reaction with a half-wave potential of 0.90 V (vs reversible hydrogen electrode) better than that of Pt/C and the oxygen evolution reaction with an overpotential of 0.46 V at the current density of 10 mA cm -2 comparable to that of RuO 2 . The activity and stability of the catalyst are also evaluated in primary and rechargeable Zn-air batteries. In both conditions, three-dimensional Fe/N-C exhibited performances superior to Pt/C. Our work demonstrates a success of utilizing an ancient science to make a state-of-the-art electrocatalyst.

Structural, mechanical, and magnetic properties of GaFe_3N thin films

International Nuclear Information System (INIS)

Junaid, Muhammad; Music, Denis; Hans, Marcus; Schneider, Jochen M.; Scholz, Tanja; Dronskowski, Richard; Primetzhofer, Daniel

2016-01-01

Using the density-functional theory, the structural, mechanical, and magnetic properties were investigated for different GaFe_3N configurations: ferromagnetic, ferrimagnetic, paramagnetic, and nonmagnetic. Ferrimagnetic and high-spin ferromagnetic states exhibit the lowest energy and are the competing ground states as the total energy difference is 0.3 meV/atom only. All theoretically predicted values could be fully confirmed by experiments. For this, the authors synthesized phase pure, homogeneous, and continuous GaFe_3N films by combinatorial reactive direct current magnetron sputtering. Despite the low melting point of gallium, the authors succeeded in the growth of GaFe_3N films at a temperature of 500 °C. Those thin films exhibit a lattice parameter of 3.794 Å and an elastic modulus of 226 ± 20 GPa. Magnetic susceptibility measurements evidence a magnetic phase transitions at 8.0 ± 0.1 K. The nearly saturated magnetic moment at ±5 T is about 1.6 μB/Fe and is close to the theoretically determined magnetic moment for a ferrimagnetic ordering (1.72 μB/Fe).

Flow behavior and microstructures of powder metallurgical CrFeCoNiMo0.2 high entropy alloy during high temperature deformation

Energy Technology Data Exchange (ETDEWEB)

Wang, Jiawen [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Yong, E-mail: yonliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Liu, Bin, E-mail: binliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Wang, Yan [School of Aeronautics and Astronautics, Central South University, Changsha 410083 (China); Cao, Yuankui; Li, Tianchen; Zhou, Rui [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2017-03-24

Dynamic recrystallization (DRX) refine grains of high entropy alloys (HEAs) and significant improve the mechanical property of HEAs, but the effect of high melting point element molybdenum (Mo) on high temperature deformation behavior has not been fully understood. In the present study, flow behavior and microstructures of powder metallurgical CrFeCoNiMo{sub 0.2} HEA were investigated by hot compression tests performed at temperatures ranging from 700 to 1100 °C with strain rates from 10{sup −3} to 1 s{sup −1}. The Arrhenius constitutive equation with strain-dependent material constants was used for modeling and prediction of flow stress. It was found that at 700 °C, the dynamic recovery is the dominant softening mechanism, whilst with the increase in compression testing temperature, the DRX becomes the dominant mechanism of softening. In the present HEA, the addition of Mo results in the high activation energy (463 kJ mol{sup −1}) and the phase separation during hot deformation. The formation of Mo-rich σ phase particles pins grain boundary migration during DRX, and therefore refines the size of recrystallized grains.

Synthesis and characterization of perovskite-type Sr{sub x}Y{sub 1−x}FeO{sub 3−δ} (0.63≤x<1.0) and Sr{sub 0.75}Y{sub 0.25}Fe{sub 1−y}M{sub y}O{sub 3−δ} (M=Cr, Mn, Ni), (y=0.2, 0.33, 0.5)

Energy Technology Data Exchange (ETDEWEB)

Biendicho, J.J. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); The ISIS Facility, STFC Rutherford Appleton Laboratory, Didcot, OX11 0QX Oxfordshire (United Kingdom); Shafeie, S. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); Frenck, L. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); Université Pierre et Marie Curie, 75005 Paris (France); Gavrilova, D. [M.V. Lomonosov Moscow State University, 119991 Moscow (Russian Federation); Böhme, S. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); Technische Universität Chemnitz, Institut für Chemie, Straße der Nationen 62, D-09111 Chemnitz (Germany); Bettanini, A.M. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); Department of Molecular Sciences and Nanosystems, University Ca’ Foscari of Venice, 30123 Venice (Italy); Svedlindh, P. [Department of Engineering Sciences, Uppsala University, Box 534, SE-751 21 Uppsala (Sweden); Hull, S. [The ISIS Facility, STFC Rutherford Appleton Laboratory, Didcot, OX11 0QX Oxfordshire (United Kingdom); Zhao, Z. [School of Industrial Engineering and Management, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Istomin, S.Ya., E-mail: istomin@icr.chem.msu.ru [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden); M.V. Lomonosov Moscow State University, 119991 Moscow (Russian Federation); Grins, J.; Svensson, G. [Department of Materials and Environmental Chemistry, Stockholm University, S-106 91 Stockholm (Sweden)

2013-04-15

Oxygen-deficient ferrates with the cubic perovskite structure Sr{sub x}Y{sub 1−x}FeO{sub 3−δ} were prepared in air (0.71≤x≤0.91) as well as in N{sub 2} (x=0.75 and 0.79) at 1573 K. The oxygen content of the compounds prepared in air increases with increasing strontium content from 3−δ=2.79(2) for x=0.75 to 3−δ=2.83(2) for x=0.91. Refinement of the crystal structure of Sr{sub 0.75}Y{sub 0.25}FeO{sub 2.79} using TOF neutron powder diffraction (NPD) data shows high anisotropic atomic displacement parameter (ADP) for the oxygen atom resulting from a substantial cation and anion disorder. Electron diffraction (ED) and high-resolution electron microscopy (HREM) studies of Sr{sub 0.75}Y{sub 0.25}FeO{sub 2.79} reveal a modulation along 〈1 0 0〉{sub p} with G± ∼0.4〈1 0 0〉{sub p} indicating a local ordering of oxygen vacancies. Magnetic susceptibility measurements at 5–390 K show spin-glass behaviour with dominating antiferromagnetic coupling between the magnetic moments of Fe cations. Among the studied compositions, Sr{sub 0.75}Y{sub 0.25}FeO{sub 2.79} shows the lowest thermal expansion coefficient (TEC) of 10.5 ppm/K in air at 298–673 K. At 773–1173 K TEC increases up to 17.2 ppm/K due to substantial reduction of oxygen content. The latter also results in a dramatic decrease of the electrical conductivity in air above 673 K. Partial substitution of Fe by Cr, Mn and Ni according to the formula Sr{sub 0.75}Y{sub 0.25}Fe{sub 1−y}M{sub y}O{sub 3−δ} (y=0.2, 0.33, 0.5) leads to cubic perovskites for all substituents with y=0.2. Their TECs are higher in comparison with un-doped Sr{sub 0.75}Y{sub 0.25}FeO{sub 2.79}. Only M=Ni has increased electrical conductivity compared to un-doped Sr{sub 0.75}Y{sub 0.25}FeO{sub 2.79}. - Graphical abstract: Oxygen-deficient ferrates with the cubic perovskite structure Sr{sub x}Y{sub 1−x}FeO{sub 3−δ} were prepared both in air (0.71≤x≤0.91) and N{sub 2} (x=0.75 and 0.79) at 1573 K. Refinement of the

Evidence for molecular N2 bubble formation in a (Ga,Fe)N magnetic semiconductor

DEFF Research Database (Denmark)

Kovács, András; Schaffer, B.; Moreno, M. S.

2011-01-01

Fe-doped GaN semiconductors are of interest for combining the properties of semiconductors and magnetic materials [1]. Depending on the growth temperature used, Fe can either be distributed homogenously in the GaN host lattice or it can accumulate in the form of Fe-N nanocrystals. As a result of ...

Study of U - Pu - Fe alloys (Masurca critical experiment)

International Nuclear Information System (INIS)

Barthelemy, P.; Boucher, R.

1965-01-01

Three compositions have been studied: 73.5 U - 25 Pu - 1.5 Fe (weight %) 74 U - 25 Pu - 1 Fe 74.5 U - 25 Pu - 0.5 Fe Elaboration and Casting are easy. After two weeks in air 74.5 U - 25 Pu - 0.5 Fe alloys are reduced in powder. As-cast alloys containing 1 and 1,5% Fe are kept undamaged during several months. A rapid oxidisation of the alloys is however observed when the samples undergo the phase transformation (at 595 deg. C and 590 deg. C respectively). Ignition tests in the presence of air show that the oxidisation starts at about 250 deg. C and that the reaction does not spread. Ignition is not observed during heating from 20 to 660 deg. C. The transformation temperature, the melting temperature and the thermal expansion coefficients have been determined by dilatometry. Below the transformation temperature, the principal phases are U-Pu zeta and (U, Pu) 6 Fe. Thermal conductibility, Young modulus, density and heat of fusion have been measured. Compatibility tests show that between U-Pu-Fe and stainless steel a phase of (U, Pu) 6 Fe type is formed. The 74 U - 25 Pu - 1% Fe alloy seems to behave better than 73.5 U - 25 Pu - 1.5% Fe alloy because the (U, Pu) 6 Fe layer is two or three times smaller. Finally, the thermal stability has been studied with the 74 U - 25 Pu - 1% Fe alloy. A dilatometric anomaly (very weak expansion) occurs when the sample is heated above transformation temperature and cooled. But there is no anomaly by thermal cycling from 50 deg. C to 400 deg. C and there is no deterioration of alloys by heat treatments at 100 deg. C, 200 deg. C, 300 deg. C during 5 months under vacuum. (authors) [fr

Preparation and characterization of sputtered Fe1-xN x films

International Nuclear Information System (INIS)

Easton, E. Bradley; Buhrmester, Th.; Dahn, J.R.

2005-01-01

Iron nitride films have been prepared by reactive DC magnetron sputtering. The composition of Fe 1-x N x was varied over a range of 0 ≤ x ≤ 0.5 by controlling the nitrogen flow rate during sputtering. These films were characterized using powder X-ray diffraction (XRD), thermogravimetric and electron microprobe analysis. We found that the nitrogen content in the films increased with nitrogen gas partial pressure. XRD experiments revealed an evolution through the α-Fe, γ'-Fe 4 N, ε-Fe 2+z N, ζ-Fe 2 N, γ'''-FeN and γ'-FeN phases, when the nitrogen gas mole percentage was increased from 0% up to 70%. Above 70%, only the γ'-FeN phase was formed despite a measurable increase in the nitrogen content of the film with nitrogen gas partial pressure. Rietveld analysis of powder X-ray diffraction patterns revealed that this behavior is due to an increase in the nitrogen site occupation factor within the lattice

Type test of the Rados MTS-N thermoluminescent dosimetry system for individual monitoring of whole body photons in HP (10); Teste de tipo do sistema de dosimetria termoluminescente RADOS MTS-N para monitoração individual de fótons de corpo inteiro em H{sub P}(10)

Energy Technology Data Exchange (ETDEWEB)

Ferreira, M.S.; Silva, E.R. da; Maurício, C.L.P., E-mail: max.das.ferreira@gmail.com, E-mail: everton@ird.gov.br, E-mail: claudia@ird.gov.br [Instituto de Radioproteção e Dosimetria (IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2017-07-01

The Institute of Radioprotection and Dosimetry (IRD/CNEN-RJ), uses an automatic thermoluminescent dosimetry (TL) system for evaluation of whole body for photons with individual monitors RADOS MTS-N, with TLF detector of LiF: Mg, Ti. The objective of this work was to characterize this system for the evaluation of H{sub P} (10) operating magnitude. The measuring range is 0.2 mSv to 2 Sv, for photon energies from 20 keV to 1250 keV. Performance tests were done for the following characteristics: homogeneity of the monitors, system reproducibility, linearity, temperature and humidity effect, energy and angular dependence and fading. The acceptance requirements used to test system performance have been drawn from national and international documents. The results obtained prove that the system can be used to measure the occupational dose of photons in H{sub P} (10)

Pressure induced magnetic phase transition in RhFe{sub 3}N and IrFe{sub 3}N: An ab-initio study

Energy Technology Data Exchange (ETDEWEB)

Puvaneswari, S. [Department of physics, E.M.G.Yadava women’s college, Madurai, Tamilnadu-625014 (India); Manikandan, M. [Department of physics, N.M.S.S.V.N college, Madurai, Tamilnadu-625019 (India); Rajeswarapalanichamy, R., E-mail: rrpalanichamy@gmail.com

2016-05-06

The structural, electronic, elastic and magnetic properties of RhFe{sub 3}N and IrFe{sub 3}N are investigated using ab-initio calculations based on density functional theory as implemented in VASP code within the gradient generalized approximation. The non-spin polarized and spin polarized calculations are performed for these nitrides at normal and high pressures. It is found that these ternary nitrides are stable in ferromagnetic state at normal pressure. The lattice constant and bulk modulus values are calculated. The electronic structure reveals that these nitrides are metallic at normal pressure. The calculated elastic constants indicate that they are mechanically stable at ambient pressure. Ferromagnetic to nonmagnetic phase transition is observed in RhFe{sub 3}N and IrFe{sub 3}N at high pressure. Ferromagnetism is quenched in these nitrides at high pressure.

Inversion of exchange bias and complex magnetization reversal in full-nitride epitaxial γ′-Fe{sub 4}N/CoN bilayers

Energy Technology Data Exchange (ETDEWEB)

Li, Z.R. [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparation Technology, Institute of Advanced Materials Physics, Faculty of Science, Tianjin University, Tianjin 300072 (China); Mi, W.B., E-mail: miwenbo@tju.edu.cn [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparation Technology, Institute of Advanced Materials Physics, Faculty of Science, Tianjin University, Tianjin 300072 (China); Wang, X.C. [Tianjin Key Laboratory of Film Electronic & Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384, China (China); Bai, H.L. [Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparation Technology, Institute of Advanced Materials Physics, Faculty of Science, Tianjin University, Tianjin 300072 (China)

2015-04-01

Exchange bias has been observed in the full-nitride epitaxial γ′-Fe{sub 4}N/CoN bilayers. With the increase of temperature, the sign of exchange bias (EB) is inverse, which is independent on the cooling field and training effect. This novel behavior appears in the bilayers with different CoN and γ′-Fe{sub 4}N thicknesses. The inversion of EB sign not only occurs at low temperatures, but also takes place even at 200 K for the 10 and 12 nm thick CoN layer. With the decreased γ′-Fe{sub 4}N layer thickness, the inversion temperature of EB sign shows a roughly increased tendency. For the bilayer with a 4 nm-thick γ′-Fe{sub 4}N, the interfacial magnetization reversal presents a complex trend, which is considered as the combined actions of the disordered ferromagnetic spins and various competed magnetic structures. This new manifestation of EB has been discussed in terms of the complicated interfacial spin structures and frustration effects due to the competition between the ferromagnetic and antiferromagnetic exchange interactions at the interface. - Highlights: • Exchange bias (EB) sign reverses from negative to positive with increasing temperature in epitaxial γ′-Fe{sub 4}N/CoN bilayers. • The positive EB can be attributed to the antiferromagnetic interfacial coupling and frustrated interfacial spin structures. • The EB transition temperature is not monotonically dependent on CoN thickness t{sub CoN}. • For a 4-nm γ′-Fe{sub 4}N, the unusual hysteresis loops are observed.

Cobalt–iron red–ox behavior in nanostructured La0.4Sr0.6Co0.8Fe0.2O3−δ cathodes

International Nuclear Information System (INIS)

Soldati, Analía L.; Baqué, Laura; Napolitano, Federico; Serquis, Adriana

2013-01-01

Nano-sized La 0.4 Sr 0.6 Co 0.8 Fe 0.2 O 3−δ (LSCF) perovskite samples (prepared by a conventional acetate route and a novel acetate synthesis with HMTA additives), were tested simulating a red–ox cycle. The crystallography was studied by X-ray Powder Diffraction (XPD) and the changes in the oxidation state of the perovskite B-site were evaluated by synchrotron X-ray Absorption Near Edge Spectroscopy (XANES). After a reducing treatment, LSFC particles show the appearance of a new phase that coexists with the original one. The structural change is accompanied by a Co and Fe formal oxidation states decrease, although Fe remains always closer to 4+ and Co closer to 3+. The treatment produces a B-site valence average reduction from 3.52+ to 3.26+ and the formation of oxygen vacancies. A re-oxidation treatment under O 2 rich atmosphere at 800 °C for 10 h shows that the change is reversible and independent of the two chemical methods used to synthesize the LSCF nano-particles. - Graphical abstract: XANES and XPD measurements in nanostructured LSCF before (black) and after (red/green) a red/ox cycle. Highlights: ► Red–ox treatments in LSCF nano-particles cause a reversible reaction. ► XPD analyses show that a new “reduced” phase coexist with the oxidize one. ► The B-site formal oxidation state decreases and the δ increases upon reduction. ► Fe remains in a higher valence (closer to 4+) than Co (close to 3+). ► The behavior seems to be independent of the synthesis method used.

DETERMINATION OF Cu, Fe, Mn, Zn AND FREE FATTY ACIDS IN PEQUI OIL

Directory of Open Access Journals (Sweden)

Aparecida M. S. Mimura

2016-06-01

Full Text Available Pequi (Caryocar brasiliense Camb., a typical fruit of the Brazilian Cerrado, is an important source of micronutrients and fatty acids. In this work, a new approach for the acid digestion (using H2SO4, HNO3 and H2O2 of pequi oil samples and the determination of Cu, Fe, Zn and Mn by flame atomic absorption spectrometry (F AAS was employed. Capillary zone electrophoresis (CZE was used for free fatty acid (FFA determination after simple and fast extraction with heated ethanol. Good results regarding precision (RSD < 10%, in most cases, sensitivity and adequate LOD and LOQ values were obtained. The accuracy was evaluated using spike tests and the recoveries were from 97 to 107%. The analytes were investigated in four different pequi oil samples. Fe was the trace element with the highest concentration (from 1.99 to 10.3 mg/100 g, followed by Zn, Mn and Cu (1.15 to 3.19, 0.42 to 0.91 and 0.31 to 0.56 mg/100 g, respectively. The main FFA found were oleic acid and palmitic acid (1.61 to 10.7 and 0.82 to 2.69 g/100 g, respectively, while linoleic acid (0.50 g/100 g was detected in only one sample. The pequi oil chemical composition showed good characteristics to be used as a food additive, in cosmetic formulations and for traditional medicine.

Magnetoresistance and magnetostriction of Ni81Fe19 and Co90Fe10 mono- and bilayer films

International Nuclear Information System (INIS)

Sahingoz, R.; Hollingworth, M.P.; Gibbs, M.R.J.; Murdoch, S.J.

2005-01-01

Monolayer and bilayer films of Ni 81 Fe 19 , Co 90 Fe 10 , Co 90 Fe 10 /Ni 81 Fe 19 , and Ni 81 Fe 19 /Co 90 Fe 10 have been grown on thermally oxidized Si. The magnetoresistance (MR) of the samples was measured as a function of applied DC magnetic field, using a four-point probe method. The magnetostriction constant, λ s , was derived from the change of anisotropy field as a function of strain. The dependence of the MR on different combinations of film layers was investigated. The magnetoresistance of the bilayers changed dramatically upon reversal of the layer order. The mono- and bilayer samples with the same material on top of the substrate showed similar MR loop shapes. However, the saturation fields of the bilayers were larger than those for the monolayers. The magnetostriction of all samples was negative. We discuss the consequences for the study and optimization of spin-valve devices

Synthesis of [Fe(Leq(Lax]n coordination polymer nanoparticles using blockcopolymer micelles

Directory of Open Access Journals (Sweden)

Christoph Göbel

2017-06-01

Full Text Available Spin-crossover compounds are a class of materials that can change their spin state from high spin (HS to low spin (LS by external stimuli such as light, pressure or temperature. Applications demand compounds with defined properties concerning the size and switchability that are maintained when the compound is integrated into composite materials. Here, we report the synthesis of [Fe(Leq(Lax]n coordination polymer (CP nanoparticles using self-assembled polystyrene-block-poly(4-vinylpyridine (PS-b-P4VP block copolymer (BCP micelles as template. Variation of the solvent (THF and toluene and the rigidity of the axial ligand Lax (Lax = 1,2-di(pyridin-4-ylethane (bpea, trans-1,2-di(pyridin-4-ylethene (bpee, and 1,2-di(pyridin-4-ylethyne (bpey; Leq = 1,2-phenylenebis(iminomethylidyne-bis(2,4-pentanedionato(2− allowed the determination of the preconditions for the selective formation of nanoparticles. A low solubility of the CP in the used solvent and a high stability of the Fe–L bond with regard to ligand exchange are necessary for the formation of composite nanoparticles where the BCP micelle is filled with the CP, as in the case of the [FeLeq(bpey]n@BCP. Otherwise, in the case of more flexible ligands or ligands that lead to high spin complexes, the formation of microcrystals next to the CP–BCP nanoparticles is observed above a certain concentration of [Fe(Leq(Lax]n. The core of the nanoparticles is about 45 nm in diameter due to the templating effect of the BCP micelle, independent of the used iron complex and [Fe(Leq(Lax]n concentration. The spin-crossover properties of the composite material are similar to those of the bulk for FeLeq(bpea]n@BCP while pronounced differences are observed in the case of [FeLeq(bpey]n@BCP nanoparticles.

Modification of Natural Zeolite with Fe(III) and Its Application as Adsorbent Chloride and Carbonate ions

Science.gov (United States)

Suhartana; Sukmasari, Emmanuella; Azmiyawati, Choiril

2018-04-01

The aim of the research is to natural zeolite with Fe(III) using anion exchange process to improve the anion exchange capacity. Natural zeolite was activated using HNO3 1 N and then mixed with FeCl3 solution and refluxed followed by oven and calcination at a temperature of 550°C. The influence of Fe(III) to zeolite was characterized by FTIR while presence of Fe in zeolite characterized by AAS. Zeolite and Zeolite-Fe adsorption capacity of chloride and carbonate anions were determined through adsorption test by variation of pH and contact time. In advanced, and then to determining the Fe adsorbed concentration at Zeolite using UV-Vis spectrophotometer. FTIR analysis result showed that the addition of Fe does not affect the zeolite’s structure but change the intensity of the zeolite spectra. The Fe concentration in Zeolite-Fe of 714 mg L-1, indicate that Fe was present in the zeolite. Both Zeolite and Zeolite-Fe adsorbtion results showed that optimum pH of Chloride anion is 2, with adsorption capacity 2,33 x 10-3 gg-1 and optimum contact time is 8 minutes. While Zeolite and Zeolite-Fe adsorbtion results showed that optimum pH of Carbonate anion is 5, with adsorption capacity 5,31 x 10-3 gg-1 and optimum contact time is 8 minutes.

Structure, nonstoichiometry, sintering and oxygen permeability of perovskite SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jin Na [College of Chemistry and Materials Science, Liaoning University of Petroleum and Chemical Technology, Fushun 113001 (China); State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Lu, Hui, E-mail: huilu@dicp.ac.cn [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023 (China); Gui, Jian Zhou [College of Chemistry and Materials Science, Liaoning University of Petroleum and Chemical Technology, Fushun 113001 (China); Kim, Jong Pyo; Son, Sou Hwan [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of); Park, Jung Hoon, E-mail: pjhoon@kier.re.kr [Greenhouse Gas Research Center, Climate Change Technology Research Division, Korea Institute of Energy Research, Daejeon 305-343 (Korea, Republic of)

2013-04-20

Highlights: ► The novel Fe/Nb co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides were characterized by the XRD, DSC, TG and SEM–EDS. ► The high structural stability of the co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides. ► The excellent oxygen permeation performance of the co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.10) membrane. -- Abstract: The novel Fe/Nb co-substituted SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides have been synthesized and characterized by X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetry (TG), and scanning electron microscopy (SEM). The XRD and DSC results demonstrate that the structural stability of the Fe/Nb co-substituted samples x = 0.05, 0.10 is improved greatly compared to the sample x = 0.00. The Fe/Nb co-doping in the SrCoO{sub 3−δ} oxide results in the improved structural stability of the SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.05, 0.10) oxides. The nonstoichiometric and sintering properties were investigated by TG and SEM, and the oxygen permeation fluxes were measured at 800–950 °C for the sample x = 0.10. The improved oxygen permeability of the ceramic SrCo{sub 1−2x}(Fe,Nb){sub x}O{sub 3−δ} (x = 0.10) membrane compared to the (Ba{sub 0.5}Sr{sub 0.5})(Co{sub 0.8}Fe{sub 0.2})O{sub 3−δ} and SrCo{sub 0.8}Fe{sub 0.2}O{sub 3–δ} membranes, was observed under an air/He oxygen partial pressure gradient at 800–950 °C.

Moessbauer and X-ray Study of Fe{sub 1-x}Al{sub x}, 0.2{<=}x{<=}0.5, Samples Produced by Mechanical Alloying

Energy Technology Data Exchange (ETDEWEB)

Oyola Lozano, D., E-mail: doyola@ut.edu.co; MartInez, Y. Rojas; Bustos, H.; Perez Alcazar, G. A. [Universidad del Tolima, Departamento de Fisica (Colombia)

2004-12-15

In this work we report the magnetic and structural properties obtained by Moessbauer spectroscopy and X-ray diffraction, of the Fe{sub 1-x}Al{sub x}, 0.2{<=}x{<=}0.5, alloys produced by mechanical alloying. Alloys with x=0.2, 0.3, 0.4 and 0.5, were for milled 12, 24, 36, and 48 hours. All the obtained alloys are in the bcc phase. The obtained Moessbauer spectra are characteristic of disordered ferromagnetic system. The lattice parameter remains nearly constant ({approx}2.91 A) for all the milling times and compositions. The mean grain sizes in the (110) and (211) direction are nearly constants with the milling time but vary from 15.5 to 11 nm and from 10.5 to 8.5 nm when Al content grow between x=0.2 to x=0.4, respectively. The difference between the mean grain sizes in these two directions shows that the grains are of prolate spheroid form.

Hydrogen storage study on Ti2CrV and ZrFe1.8V0.2 composite system

International Nuclear Information System (INIS)

Banerjee, S.; Kumar, A.; Pillai, C.G.S.; Sudarsan, V.

2012-01-01

Ti 2 CrV is reported to have one of the highest hydrogen storage capacities (more than 4 wt. %) among the bcc phase transition metal alloys. It has been found from the earlier study that Ti 2 CrV alloy shows quite good hydrogen absorption property but the desorption temperature is on the higher side. The in-situ temperature programmed desorption profile shows that the hydrogen desorption starts from 120℃ and the desorption peak comes at 180℃, which is slightly high for the vehicular application. On the other hand ZrFe 1.8 V 0.2 Laves phase alloy has low hydrogen absorption capacity, but at the room temperature it can desorp all its hydrogen. The pressure composition isotherm of ZrFe 1.8 V 0.2 alloy generated during the experiment shows the typical characteristics of the room temperature reversible hydride. The in-situ temperature programmed desorption shows that the hydride can desorb all the hydrogen below room temperature

DETERMINATION OF LIMIT DETECTION OF THE ELEMENTS N, P, K, Si, Al, Fe, Cu, Cd, WITH FAST NEUTRON ACTIVATION USING NEUTRON GENERATOR

OpenAIRE

Sunardi, Sunardi; Muryono, Muryono

2010-01-01

Determination of limit detection of the elements N, P, K, Si, Al, Fe, Cu, Cd, with fast neutron activation using neutron generator has been done.  Samples prepared from SRM 2704, N, P, K elements from MERCK, Cu, Cd, Al from activation foil made in San Carlos, weighted and packed for certain weight then iradiated during 30 minutes with 14 MeV fast neutron using the neutron generator and then counted with gamma spectrometry (accuspec).  At this research condition of neutron generator was set at...

Fe(II)-substituted cobalt ferrite nanoparticles against multidrug resistant microorganisms

Science.gov (United States)

Žalnėravičius, Rokas; Paškevičius, Algimantas; Mažeika, Kęstutis; Jagminas, Arūnas

2018-03-01

The present study is focused on the determination the influence of cobalt content in the magnetic cobalt ferrite nanoparticles (Nps) on their antibacterial efficiency against gram-negative Escherichia coli and gram-positive Staphylococcus aureus bacteria and several Candida species, in particular C. parapsilosis and C. albicans. For the synthesis of Fe(II) substituted cobalt ferrite Nps by co-precipitation way, the L-lysine was used as the capping biocompatible agent and the particle size was successfully controlled to be in the range of 5-6.4 nm. The antimicrobial efficiencies of the CoxFe1-xFe2O4@Lys Nps, where x varies from 0.2 to 1.0, were evaluated through the quantitative analysis by comparing with that of Fe3O4@Lys Nps and L-lysine. In this way, it was evidenced that increase in the Co2+ content in the similar sized cobalt ferrite Nps resulted in an increase in their antimicrobial potency into 93.1-86.3 % for eukaryotic and into 96.4-42.7 % for prokaryotic strains. For characterization the composition, structure, and morphology of the tested herein Nps inductively coupled plasma optical emission spectrometry, X-ray diffraction, high-resolution transmission electron microscopy, Mössbauer, and FTIR spectroscopy techniques were conferred.

Epitaxial integration of CoFe2O4 thin films on Si (001) surfaces using TiN buffer layers

Science.gov (United States)

Prieto, Pilar; Marco, José F.; Prieto, José E.; Ruiz-Gomez, Sandra; Perez, Lucas; del Real, Rafael P.; Vázquez, Manuel; de la Figuera, Juan

2018-04-01

Epitaxial cobalt ferrite thin films with strong in-plane magnetic anisotropy have been grown on Si (001) substrates using a TiN buffer layer. The epitaxial films have been grown by ion beam sputtering using either metallic, CoFe2, or ceramic, CoFe2O4, targets. X-ray diffraction (XRD) and Rutherford spectrometry (RBS) in random and channeling configuration have been used to determine the epitaxial relationship CoFe2O4 [100]/TiN [100]/Si [100]. Mössbauer spectroscopy, in combination with XRD and RBS, has been used to determine the composition and structure of the cobalt ferrite thin films. The TiN buffer layer induces a compressive strain in the cobalt ferrite thin films giving rise to an in-plane magnetic anisotropy. The degree of in-plane anisotropy depends on the lattice mismatch between CoFe2O4 and TiN, which is larger for CoFe2O4 thin films grown on the reactive sputtering process with ceramic targets.

Influence of manganese, carbon and nitrogen on high-temperature strength of Fe-Cr-Mn austenitic alloys

International Nuclear Information System (INIS)

Hosoi, Y.; Okazaki, Y.; Wade, N.; Miyahara, K.

1990-01-01

High Mn-Cr-Fe base alloys are candidates for the first wall material of fusion reactors because of rapid decay of radioactivity of the alloys after neutron irradiation compared with that of Ni-Cr-Fe base alloys. Their high temperature properties, however, are not clearly understood at present. In this paper, a study has been made of the effects of Mn, C and N content on the high-temperature tensile strength and creep properties of a 12% CR-Fe base alloy. Mn tends to decrease tensile strength and proof stress at intermediate temperatures. At higher temperatures in the austenite range, however, tensile properties scarcely depend on Mn content. C and N additions improve the tensile properties markedly. The combined addition of 0.2%C and 0.2%N to a 12%Cr-15%Mn-Fe base alloy makes the strength at 873K as high as that of a modified type 316 stainless steel. Combined alloying with C and N also improves the creep strength. Cold working is very useful in increasing the creep strength because of the finely dispersed precipitates in the matrix during creep. From these results, Fe-12%Cr-15%Mn-15%Mn-0.2%c-0.2%N is recommended as one of the most suitable alloys in this system for high temperature usage. (author)

Structural, mechanical, and magnetic properties of GaFe{sub 3}N thin films

Energy Technology Data Exchange (ETDEWEB)

Junaid, Muhammad, E-mail: junaid@mch.rwth-aachen.de; Music, Denis, E-mail: music@mch.rwth-aachen.de; Hans, Marcus; Schneider, Jochen M. [Materials Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Scholz, Tanja; Dronskowski, Richard [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Primetzhofer, Daniel [Department of Physics and Astronomy, Uppsala University, Lägerhyddsvägen 1, S-75120 Uppsala (Sweden)

2016-07-15

Using the density-functional theory, the structural, mechanical, and magnetic properties were investigated for different GaFe{sub 3}N configurations: ferromagnetic, ferrimagnetic, paramagnetic, and nonmagnetic. Ferrimagnetic and high-spin ferromagnetic states exhibit the lowest energy and are the competing ground states as the total energy difference is 0.3 meV/atom only. All theoretically predicted values could be fully confirmed by experiments. For this, the authors synthesized phase pure, homogeneous, and continuous GaFe{sub 3}N films by combinatorial reactive direct current magnetron sputtering. Despite the low melting point of gallium, the authors succeeded in the growth of GaFe{sub 3}N films at a temperature of 500 °C. Those thin films exhibit a lattice parameter of 3.794 Å and an elastic modulus of 226 ± 20 GPa. Magnetic susceptibility measurements evidence a magnetic phase transitions at 8.0 ± 0.1 K. The nearly saturated magnetic moment at ±5 T is about 1.6 μB/Fe and is close to the theoretically determined magnetic moment for a ferrimagnetic ordering (1.72 μB/Fe).

Determination of hyperfine fields and atomic ordering in NiMnFeGe exhibiting martensitic transformation

Directory of Open Access Journals (Sweden)

Satuła Dariusz

2015-03-01

Full Text Available The hyperfine fields and atomic ordering in Ni1−xFexMnGe (x = 0.1, 0.2, 0.3 alloys were investigated using X-ray diffraction and Mössbauer spectroscopy at room temperature. The X-ray diffraction measurements show that the samples with x = 0.2, 0.3 crystallized in the hexagonal Ni2In-type of structure, whereas in the sample with x = 0.1, the coexistence of two phases, Ni2In- and orthorhombic TiNiSi-type of structures, were found. The Mössbauer spectra measured with x = 0.2, 0.3 show three doublets with different values of isomer shift (IS and quadrupole splitting (QS related to three different local surroundings of Fe atoms in the hexagonal Ni2In-type structure. It was shown that Fe atoms in the hexagonal Ni2In-type structure of as-cast Ni1−xFexMnGe alloys are preferentially located in Ni sites and small amount of Fe is located in Mn and probably in Ge sites. The spectrum for x = 0.1 shows the doublets in the central part of spectrum and a broad sextet. The doublets originate from the Fe atoms in the paramagnetic state of hexagonal Ni2In-type structure, whereas the sextet results from the Fe atoms in orthorhombic TiNiSi-type structure.

DETERMINATION OF LIMIT DETECTION OF THE ELEMENTS N, P, K, Si, Al, Fe, Cu, Cd, WITH FAST NEUTRON ACTIVATION USING NEUTRON GENERATOR

Directory of Open Access Journals (Sweden)

Sunardi Sunardi

2010-06-01

Full Text Available Determination of limit detection of the elements N, P, K, Si, Al, Fe, Cu, Cd, with fast neutron activation using neutron generator has been done.  Samples prepared from SRM 2704, N, P, K elements from MERCK, Cu, Cd, Al from activation foil made in San Carlos, weighted and packed for certain weight then iradiated during 30 minutes with 14 MeV fast neutron using the neutron generator and then counted with gamma spectrometry (accuspec.  At this research condition of neutron generator was set at current 1 mA that produced neutron flux about 5,47.107 n/cm2.s and  experimental result shown that the limit detection for the elements N, P, K, Si, Al, Fe, Cu, Cd are  2,44 ppm, 1,88 ppm, 2,15 ppm, 1,44 ppm, 1,26 ppm, 1,35 ppm, 1,05 ppm, 2,99 ppm, respectively.  The data  indicate that the limit detection or sensitivity of appliance of neutron generator to analyze the element is very good, which is feasible to get accreditation AANC laboratory using neutron generator.   Keywords: limit detection, AANC, neutron generator

Neutron transitions within the S=10 ground multiplet of a Fe8 magnetic cluster

Science.gov (United States)

Carretta, S.; Liviotti, E.; Amoretti, G.; Caciuffo, R.; Caneschi, A.; Gatteschi, D.

2002-02-01

Inelastic neutron scattering has been used to determine the anisotropic spin Hamiltonian that splits the S=10 ground multiplet of the cluster (tacn)6Fe8O2(OH)12Br4.3(ClO4)3.76H2O (Fe8PCl), where (tacn) is the organic ligand 1,4,7-triazacyclononane. This single-molecule magnet,which is obtained from the well known Fe8Br cluster, by partial replacement of the bromide ions by perchlorate anions, presents a larger transverse anisotropy than the parent compound, the E/D ratio being 0.22 instead of 0.16. This is in agreement with the relaxation measurements in the pure quantum tunneling regime. The details of the neutron spectra detected at three different temperatures (2, 10, and 15 K) allowed us to determine the spin Hamiltonian parameters up to fourth order and to identify the main source of the transition linewidth broadening with the occupational disorder of the bromide and perchlorate ions, rather than with the random internal dipolar field distribution.

78 FR 69703 - 10-Day Notice of Proposed Information Collection: Generic Customer Satisfaction Surveys; Physical...

Science.gov (United States)

2013-11-20

... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5683-N-102] 10-Day Notice of Proposed Information Collection: Generic Customer Satisfaction Surveys; Physical Inspection Pilot Program...

Evaluation of the 46Ti(n,2n)45Ti and 54Fe(n,2n)53m+gFe reaction cross sections for neutron dosimetry in fusion facilities

International Nuclear Information System (INIS)

Badikov, S.A.; Ignatyuk, A.V.; Zolotarev, K.I.; Pashchenko, A.B.

1993-11-01

The reaction cross-sections of 46 Ti(n,2n) 45 Ti and 54 Fe(n,2n) 53m+g Fe, which are important for fusion reactor neutron dosimetry, were evaluated using a generalized least squares method. The experimental cross-section data of all measurements performed up to January 1993, were critically reviewed. The evaluated cross-section data are presented in analytical form and in ENDF-6 format, including covariance data. (author)

Structural, magnetic and magneto-transport properties of thermally evaporated Fe/Cu multilayers

Energy Technology Data Exchange (ETDEWEB)

Bouziane, K.; Al-Busaidi, M.; Gismelseed, A.; Al-Rawas, A. [Physics Department, College of Science, Sultan Qabos University, P. O. Box 36, Postal Code 123, Al-Khodh, Muscat (Oman)

2004-05-01

Structural, magnetic and magneto-transport properties of thermally evaporated Fe/Cu multilayers (MLs) have been investigated. Although multilayered structure has been successfully obtained, a substantial interfacial roughness ranging from 0.6 nm to 1.2 nm has been determined. All Fe/Cu MLs were polycrystalline with an average grain size of about 10 nm. Fe was bcc and textured (110) whereas Cu was fcc(111). Transmission electron microscopy analysis showed that the fcc Cu layer was rather textured (110) and (100) at least in the first stage of growth of the Fe/Cu MLs. Conversion electron Moessbauer (CEMS) measurements indicated the existence of three phases. Two of them were magnetic with a dominant bcc Fe phase, followed by fcc Fe phase. The third phase was superparamagnetic. The CEMS results were explained in terms of the partial diffusion of Fe into Cu with three different zones. The small magnetoresistance (MR<0.2%) was correlated to Fe clusters located at Fe-Cu interfaces. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

Structural and magnetic properties of Ni0.8M0.2Fe2O4 (M = Cu, Co) nano-crystalline ferrites

Science.gov (United States)

Vijaya Babu, K.; Satyanarayana, G.; Sailaja, B.; Santosh Kumar, G. V.; Jalaiah, K.; Ravi, M.

2018-06-01

Nano-crystalline nickel ferrites are interesting materials due to their large physical and magnetic properties. In the present work, two kinds of spinel ferrites Ni0.8M0.2Fe2O4 (M = Cu, Co) are synthesized by using sol-gel auto-combustion method and the results are compared with NiFe2O4. The structural properties of synthesized ferrites are determined by using X-ray powder diffraction; scanning electron microscope and Fourier transform infrared spectroscopy. The cation distribution obtained from X-ray diffraction show that cobalt/copper occupies only tetrahedral site in spinel lattice. The lattice constant increases with the substitution of cobalt/copper. The structural parameters like bond lengths, tetrahedral and octahedral edges have been varied with the substitution. The microstructural study is carried out by using SEM technique and the average grain size is increased with nickel ferrite. The initial permeability (μi) is improving with the substitution. The observed g-value from ESR is approximately equal to standard value.

75 FR 1547 - Alcohol and Drug Testing: Determination of Minimum Random Testing Rates for 2010

Science.gov (United States)

2010-01-12

...-11213, Notice No. 13] RIN 2130-AA81 Alcohol and Drug Testing: Determination of Minimum Random Testing... percent for alcohol. Because the industry-wide random drug testing positive rate has remained below 1.0... effective upon publication. FOR FURTHER INFORMATION CONTACT: Lamar Allen, Alcohol and Drug Program Manager...

Características de los recubrimientos WC-NiCrBSiFe en función del sistema de proyección térmica

Directory of Open Access Journals (Sweden)

Higuera-Hidalgo, V.

2004-10-01

Full Text Available WC-NiCrBSiFe coatings are normally used as protection against heat, corrosion and erosion actions encountered in superheater and reheater tubes in power plant boilers. This coating was thermal-spray projected using different procedures (plasma, HVOF and HFPD onto stainless steel specimens. The microstructures, porosities, oxide contents and microhardnesses of the coatings were determined. Thermal fatigue tests under simulative power plant service conditions were conducted in an experimental combustion chamber and, finally, the adhesion between the substrate and the coating layer was evaluated by means of tensile tests.The obtained results are discussed, and special attention was paid to the specific characteristics of the different spraying procedures.

El material tipo cermet WC-NiCrBSiFe se emplea como elemento protector frente al desgaste, en elementos de calderas de vapor, como son los sobrecalentadores y recalentadores de vapor, donde las condiciones de servicio tan severas (alta temperatura, erosión por cenizas volantes, etc. acortan notablemente la vida útil de los materiales convencionales empleados. En este trabajo se ha realizado la proyección térmica de este recubrimiento por arco plasma no transferido, proyección mediante llama a elevada velocidad (HVOF y proyección por detonación a elevada frecuencia (HFPD. Se determinaron las microestructuras, porosidades, contenidos en óxidos y microdurezas de los distintos recubrimientos obtenidos. También, se llevaron a cabo ensayos de fatiga térmica en condiciones similares a las imperantes en el interior de una caldera, mediante el empleo de un combustor experimental. Finalmente, se determinó la adherencia de las capas a los sustratos receptores, mediante ensayos de tracción. Los resultados obtenidos son discutidos en función de las características específicas de los diferentes sistemas de proyección utilizados.

Sequential determination of multi-nutrient elements in natural water samples with a reverse flow injection system.

Science.gov (United States)

Lin, Kunning; Ma, Jian; Yuan, Dongxing; Feng, Sichao; Su, Haitao; Huang, Yongming; Shangguan, Qipei

2017-05-15

An integrated system was developed for automatic and sequential determination of NO 2 - , NO 3 - , PO 4 3- , Fe 2+ , Fe 3+ and Mn 2+ in natural waters based on reverse flow injection analysis combined with spectrophotometric detection. The system operation was controlled by a single chip microcomputer and laboratory-programmed software written in LabVIEW. The experimental parameters for each nutrient element analysis were optimized based on a univariate experimental design, and interferences from common ions were evaluated. The upper limits of the linear range (along with detection limit, µmolL -1 ) of the proposed method was 20 (0.03), 200 (0.7), 12 (0.3), 5 (0.03), 5 (0.03), 9 (0.2) µmolL -1 , for NO 2 - , NO 3 - , PO 4 3- , Fe 2+ , Fe 3+ and Mn 2+ , respectively. The relative standard deviations were below 5% (n=9-13) and the recoveries varied from 88.0±1.0% to 104.5±1.0% for spiked water samples. The sample throughput was about 20h -1 . This system has been successfully applied for the determination of multi-nutrient elements in different kinds of water samples and showed good agreement with reference methods (slope 1.0260±0.0043, R 2 =0.9991, n=50). Copyright © 2017 Elsevier B.V. All rights reserved.

Experiment data report for semiscale Mod-1, test S-02-7. Blowndown heat transfer test

International Nuclear Information System (INIS)

Crapo, H.S.; Jensen, M.F.; Sackett, K.E.

1975-11-01

Recorded test data are presented for Test S-02-7 of the Semiscale Mod-1 blowdown heat transfer test series conducted to investigate the thermal and hydraulic phenomena accompanying an hypothesized loss-of-coolant accident (LOCA) in a water-cooled nuclear reactor system and to provide data for the assessment of the Loss-of-Fluid Test (LOFT) design basis. Test S-02-7 was conducted from an initial cold leg fluid temperature of 543 0 F and an initial pressure of 2,263 psia. A simulated double-ended offset shear cold leg break was used to investigate the system response to a depressurization transient with full design core power (1.6 MW). An electrically heated core was used in the pressure vessel to simulate the effects of a nuclear core with power set to provide a flat radial power profile. System flow was set to achieve the full design core temperature differential of 66 0 F. Blowdown to the pressure suppression system was accomplished without simulated emergency core cooling injection or pressure suppression system coolant spray. The uninterpreted data from Test S-02-7 are presented for future data analysis and test results reporting activities. The data, presented in the form of graphs in engineering units, have been analyzed only to the extent necessary to assure that they are reasonable and consistent. Also included as an appendix are selected data from a test identified as Test S-02-7C. This test was an initial attempt at Test S-02-7 in which an inadvertent power trip occurred at 2.3 seconds after rupture. Selected data comparisons of the results from Test S-02-7 and S-02-7C are presented to indicate the repeatability of system behavior

Synthesis, electrochemical investigation and structural analysis of doped Li[Ni0.6Mn0.2Co0.2-xMx]O2 (x = 0, 0.05; M = Al, Fe, Sn) cathode materials

Science.gov (United States)

Eilers-Rethwisch, Matthias; Winter, Martin; Schappacher, Falko Mark

2018-05-01

Layered Ni-rich Li[Ni0.6Mn0.2Co0.2-xMx]O2 cathode materials (x = 0, 0.05; M = Al, Fe, Sn) are synthesized via a co-precipitation synthesis route and the effect of dopants on the structure and electrochemical performance is investigated. All synthesized materials show a well-defined layered structure of the hexagonal α-NaFeO2 phase investigated by X-ray diffraction (XRD). Undoped LiNi0.6Mn0.2Co0.2O2 exhibits a discharge capacity of 170 mAh g-1 in Li-metal 2032 coin-type cells. Doped materials reach lower capacities between 145 mAh g-1 for Al and 160 mAh g-1 for Sn. However, all doped materials prolong the cycle life by up to 20%. Changes of the lattice parameter before and after delithiation yield information about structural stability. A smaller repulsion of the transition metal layer during delithiation in the Sn-doped material leads to a smaller expansion of the unit cell, which results in enhanced structural stability of the material. The improved structural stability of Sn-doped NMC cathode active material is proven by thermal investigations with the help of Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA).

Study on magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys

Energy Technology Data Exchange (ETDEWEB)

Tan, G.S.; Xu, H., E-mail: huixu8888@shu.edu.cn; Yu, L.Y.; Tan, X.H.; Zhang, Q.; Gu, Y.; Hou, X.L.

2017-09-01

Highlights: • (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B alloys are prepared by melt-spinning method with simultaneously decreasing of Nd, Ce concentration. • The magnetic properties B{sub r}, (BH){sub max} and squareness are all improved with an appropriate reduction of Nd, Ce concentration. • Magnetic field heat treatment offers a significant improvement in B{sub r}, (BH){sub max} and squareness. - Abstract: In the present work, (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) permanent alloys are prepared by melt-spinning method. The hard magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys annealed at optimum temperatures have been investigated systematically. Depending on the Nd, Ce concentration, the maximum energy product ((BH){sub max}) and remanence (B{sub r}) increase gradually with x in the range of 0 ≤ x ≤ 0.4, whereas decrease gradually in the alloys with 0.4 < x ≤ 0.6. It is found that the optimum magnetic properties are obtained at x = 0.4: H{sub ci} = 4.9 kOe, B{sub r} = 10.1 kG, (BH){sub max} = 13.7 MGOe. Specifically, magnetic field heat treatment below the Curie temperature is applied for (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B (x = 0.4) annealed ribbons. The magnetic properties B{sub r}, (BH){sub max} and squareness are all enhanced after the magnetic field heat treatment. The (BH){sub max} shows a substantial increase from 13.7 MGOe to 16.0 MGOe after the heat treatment at 623 K with a magnetic field of 1 T, which gets 17% improvement compared with that of the sample without a magnetic field heat treatment. We demonstrate that the magnetic field heat treatment plays a certain role in the magnetization reversal behavior and can improve the microstructure of (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B alloy.

Design and Micromagnetic Simulation of Fe/L10-FePt/Fe Trilayer for Exchange Coupled Composite Bit Patterned Media at Ultrahigh Areal Density

Directory of Open Access Journals (Sweden)

Warunee Tipcharoen

2015-01-01

Full Text Available Exchange coupled composite bit patterned media (ECC-BPM are one candidate to solve the trilemma issues, overcome superparamagnetic limitations, and obtain ultrahigh areal density. In this work, the ECC continuous media and ECC-BPM of Fe/L10-FePt/Fe trilayer schemes are proposed and investigated based on the Landau-Lifshitz-Gilbert equation. The switching field, Hsw, of the hard phase in the proposed continuous ECC trilayer media structure is reduced below the maximum write head field at interlayer exchange coupling between hard and soft phases, Aex, higher than 20 pJ/m and its value is lower than that for continuous L10-FePt single layer media and L10-FePt/Fe bilayer. Furthermore, the Hsw of the proposed ECC-BPM is lower than the maximum write head field with exchange coupling coefficient between neighboring dots of 5 pJ/m and Aex over 10 pJ/m. Therefore, the proposed ECC-BPM trilayer has the highest potential and is suitable for ultrahigh areal density magnetic recording technology at ultrahigh areal density. The results of this work may be gainful idea for nanopatterning in magnetic media nanotechnology.

Structural and electrochemical properties of La 0.8Sr 0.2Ga 1-xFe xO 3

Science.gov (United States)

Mori, Kazuhiro; Onodera, Yohei; Kiyanagi, Ryoji; Richardson, James W.; Itoh, Keiji; Sugiyama, Masaaki; Kamiyama, Takashi; Fukunaga, Toshiharu

2009-02-01

Mixed ionic-electronic conductor of Fe doped lanthanum gallate, La 0.8Sr 0.2Ga 1-xFe xO 3, has been studied by the dc four-probe method and the neutron powder diffraction. In the electrical conductivity measurement at RT, insulator-metal transition-like phenomenon was observed at around x˜0.35; this suggests an existence of the percolation limit for the electronic conductivity. Simultaneously, a bond length between O atoms, lO-O, in a MO 6 octahedron (M dbnd Ga 1-xFe x) drastically expands over x˜0.4, according to the result of crystal structure refinement based on the hexagonal phase. Such a drastic expansion in the lO-O would induce the decrease in the oxygen ionic conductivity.

Magnetic properties of NdMn{sub 1−x}Fe{sub x}O{sub 3+δ} (0≤x≤0.3) system

Energy Technology Data Exchange (ETDEWEB)

Mihalik, Matúš, E-mail: matmihalik@saske.sk [Institute of Experimental Physics SAS, Watsonova 47, 040 01 Košice (Slovakia); Mihalik, Marián [Institute of Experimental Physics SAS, Watsonova 47, 040 01 Košice (Slovakia); Fitta, M.; Bałanda, M. [Institute of Nuclear Physics Polish Academy of Sciences, Radzikowskiego 152, 31-342 Kraków (Poland); Vavra, M. [Institute of Experimental Physics SAS, Watsonova 47, 040 01 Košice (Slovakia); P.J. Šafárik University, Moyzesova 11, 041 54 Košice (Slovakia); Gabáni, S.; Zentková, M. [Institute of Experimental Physics SAS, Watsonova 47, 040 01 Košice (Slovakia); Briančin, J. [Institute of Geotechnics SAS, Watsonova 45, 043 53 Košice (Slovakia)

2013-11-15

We have studied the effect of Fe for Mn substitution on magnetic properties of NdMn{sub 1−x}Fe{sub x}O{sub 3+δ} compounds. Our heat capacity, AC susceptibility and magnetization measurements revealed that the transition from paramagnetic to magnetically ordered state of the Mn sublattice decreases linearly from T{sub N}=74.9 K to T{sub N}=49 K with doping up to x=0.25. The ordering temperature T{sub 1} of Nd sublattice varies in a non-monotonous way in the temperature range 11–16 K. For x=0.3, the ordering of the Mn/Fe sublattice is residual, while the magnetism in Nd sublattice seems to be intact. The broad maximum in heat capacity C(T) at about 10 K was ascribed by 2-level Schottky contribution (Δ=21(1) K) for x=0, but this description failed for Fe-doped samples. An upturn of C(T) at temperatures below 0.5 K was observed on NdMnO{sub 3} and can be accounted to nuclear contribution. A more detailed study of AC susceptibility performed on samples with x=0.1 and 0.2 revealed a shift of both peaks to higher temperature with increasing frequency. The compensation temperature and a large negative field-cooled magnetization was observed for concentrations x=0.2 and x=0.25. - Highlights: • Fe substitution into NdMnO{sub 3} compound decreases T{sub N} by 10 K for 10% of Fe. • In this compound: Nd and Mn ions both order magnetically. • “Butterfly-type” hysteresis loops in the ordered state.

Modificación de arcillas colombianas con pilares mixtos de Al-Fe y su evaluación en la oxidación catalítica de fenol en solución acuosa diluida

Directory of Open Access Journals (Sweden)

Luis Galeano

2010-11-01

Full Text Available La legislación ambiental es particularmente restrictiva respecto a la disposición de contaminantes biorrefractarios presentes en aguas residuales. Las arcillas pilarizadas tienen gran versatilidad para ajustarse a reacciones de interés ambiental, entre otras. En el presente estudio se logran modificar arcillas de origen colombiano con soluciones de pilares mixtos Al-Fe, las cuales muestran un excelente desempeño en la oxidación catalítica de soluciones acuosas con contenidos medios de carbono orgánico total COT (36 mg C/L. Con los materiales sintetizados se alcanza una conversión total de fenol, molécula contaminante modelo, en 2 horas de reacción a 20°C y presión atmosférica; en 4 horas de reacción, se alcanza la remoción de hasta el 62% de COT de la solución obteniéndose, principalmente, ácidos carboxílicos ligeros como subproductos, además de CO. Los materiales son estables al medio fuertemente oxidante de la reacción, y el Fe lixiviado en la solución se encuentra en un valor cercano a 0,2 mg/L para el material de mejor desempeño catalítico.

Chromatography on cellulose exchangers: microdetermination of Fe/sup 3 +/, UO/sub 2//sup 2 +/, and Cu/sup 2 +/ ions in aqueous solutions by means of small separation columns

Energy Technology Data Exchange (ETDEWEB)

Burba, P; Lieser, K H

1978-01-01

A study of the use of small separation columns filled with a cellulose exchanger containing salicylic acid as the anchor group for chromatographic determination of Fe/sup 3 +/ and Cu/sup 2 +/ in aqueous solution is described. The detection limits are Fe approx.0.2 and Cu 10 ..mu..g. The separation and simultaneous determination of several ions is possible.

Crystal structure of superparamagnetic Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4} nanoparticles synthesized by sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Escamilla-Pérez, A.M., E-mail: angel.mep@gmail.com [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Cortés-Hernández, D.A., E-mail: dora.cortes@cinvestav.edu.mx [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Almanza-Robles, J.M. [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Mantovani, D.; Chevallier, P. [Laboratory for Biomaterials and Bioengineering, Department of Materials Engineering and University Hospital Research Center, Laval University, Quebec City, QC (Canada)

2015-01-15

Powders of magnetic iron oxide nanoparticles (Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4}) were prepared by a sol–gel method using ethylene glycol and nitrates of Fe, Ca and Mg as starting materials. Those powders were heat treated at different temperatures (573, 673, 773 and 873 K). In order to evaluate the effect of the heat treatment temperature on the nanoferrites properties, X-ray diffraction (XRD), vibrating sample magnetometry (VSM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques were used. It was found that the reaction products exhibit nanometric sizes and superparamagnetic behavior. It is also demonstrated that, as the heat treatment temperature increases, the particle size and the saturation magnetization of the nanoferrites are increased. - Highlights: • Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4} superparamagnetic nanoparticles were successfully synthesized. • Particle average sizes of Ca–Mg ferrites were within the range of 8–25 nm. • The nanoferrite treated at 873 K showed a stoichiometry close to Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4}. • The heat treatment temperature has a strong effect on the crystal structure. • These nanoparticles are potential materials for magnetic hyperthermia.

Study of microstructure and magnetic properties of L10 FePt/SiO2 thin films

Directory of Open Access Journals (Sweden)

Giannopoulos G.

2014-07-01

Full Text Available Achieving magnetic recording densities in excess of 1Tbit/in2 requires not only perpendicular media with anisotropies larger than 7 MJ/m3, making FePt alloys an ideal choice, but also a narrow distribution below 10 nm for a reduced S/N ratio. Such grain size reduction and shape control are crucial parameters for high density magnetic recording, along with high thermal stability. Previous work has shown that the L10 FePt grain size can be controlled by alloying FePt with materials such as C, Ag, and insulators such as AlOx, MgO. Au and Al2O3 also act to segregate and magnetically decouple the FePt grains. Better results were obtained with C with respect to the uniformity of grains and SiO2 with respect to the shape. We present our results on co-sputtering FePt with C or SiO2 (up to 30 vol % on MgO (001 single crystal substrates at 350 and 500 oC. With C or SiO2 addition we achieved grain size reduction, shape control and isolated structure formation, producing continuous films with high uniformity and a narrow grain size distribution. These additions thus allow us to simultaneously control the coercivity and the S/N ratio. We also will report structural and microstructural properties.

Microstructure and mechanical properties of ion-beam-produced Fe-Ti-(N), Fe-Ti-(C), and Fe-Ti-(C,N) surface films

Science.gov (United States)

Hirvonen, J.-P.; Nastasi, M.; Zocco, T. G.; Jervis, T. R.

1990-06-01

Ion-mixed films of Fe53 Ti47 were produced by ion irradiating a Fe-Ti multilayer structure on AISI 304 stainless steel. The ion-mixed films were subsequently implanted with nitrogen, carbon, or both carbon and nitrogen. The microstructure following nitrogen implantation consisted of a bcc solid solution of iron and titanium and finely dispersed TiN precipitates. In the cases of carbon or carbon and nitrogen implantation, a two-phase structure consisting of an amorphous matrix with TiC or Ti(C,N) precipitates was found. All these films initially possessed improved tribological properties as revealed by lowered friction and increased wear resistance. However, after an extended test of 1000 wear cycles, a reduced friction was only observed for the carbon or carbon and nitrogen implanted samples. The wear track on the dual implanted surface was extremely smooth, while the surface of the nitrogen-implanted sample was partly worn through, causing the friction to increase to the level of the untreated sample. The improved tribological properties of the implanted films are attributed to an increase in surface hardness. However, the surface hardness is unable to explain differences between different implantations. In the case of the dual carbon and nitrogen implantation, improvements appear to be in part the result from an increased capability to accommodate plastic deformation. These conclusions are supported by transmission electron microscope studies of the wear tracks as well as by nanoindentation measurements.

(2S,7S-10-Ethyl-1,8,10,12-tetraazatetracyclo[8.3.1.18,12.02,7]pentadecan-10-ium iodide

Directory of Open Access Journals (Sweden)

Augusto Rivera

2012-10-01

Full Text Available The title chiral quaternary ammonium salt, C13H25N4+·I−, was synthesized through the Menschutkin reaction between the cage aminal (2S,7S-1,8,10,12-tetraazatetracyclo[8.3.1.18,12.02,7]pentadecane and ethyl iodide. The quaternization occurred regioselectively on the nitrogen with major sp3 character. The crystal structure consists of anions and cations separated by normal distances. Ions are not linked through C—H...I hydrogen bonds.

Influence of ionic conductivity of the nano-particulate coating phase on oxygen surface exchange of La0.58Sr0.4Co0.2Fe0.8O3-δ

NARCIS (Netherlands)

Saher, S.; Naqash, S.; Boukamp, Bernard A.; Hu, Bobing; Xia, Changrong; Bouwmeester, Henricus J.M.

2017-01-01

The oxygen surface exchange kinetics of mixed-conducting perovskite La0.58Sr0.4Co0.2Fe0.8O3 d (LSCF) ceramics coated with a porous nano-particulate layer of either gadolinea (Gd2O3), ceria (CeO2) or 20 mol% Gd-doped ceria (GCO) was determined by electrical conductivity relaxation (ECR). The

Positron annihilation in gaseous nitrided cold-rolled FeNiTi films

NARCIS (Netherlands)

Chechenin, NG; van Veen, A; Galindo, RE; Schut, H; Chezan, A; Boerma, DO; Triftshauser, W; Kogel, G; Sperr, P

2001-01-01

Positron beam analysis (PBA) was performed on cold-rolled Fe0.94Ni0.04Ti0.02 foils, which were subjected to different thermal treatments in an atmosphere of a gas mixture of NH3+H-2 (nitriding). The nitriding of the samples in the alpha -region (alphaN) of Lehrer diagram for the Fe-N system produced

The origin of high magnetic properties in (R,Zr)(Fe,Co)11.0–11.5Ti1.0–0.5Ny (y=1.0–1.4 for R=Nd, y=0 for R=Sm) compounds

International Nuclear Information System (INIS)

Kobayashi, K.; Suzuki, S.; Kuno, T.; Urushibata, K.; Sakuma, N.; Yano, M.; Shoji, T.; Kato, A.; Manabe, A.

2017-01-01

Ten alloys and nitrogenated compounds of (R,Zr)(Fe,Co) 11.0–11.5 Ti 1.0–0.5 N y (y=1.0–1.4 for R=Nd, y=0 for R=Sm) with a ThMn 12 -type structure were prepared. The average Fe–Fe interatomic distances, d(Fe–Fe), for Fe sites were calculated based on the reported atomic parameters. The hyperfine splittings (inner field (IF), in teslas) were measured by Mössbauer spectroscopy, and the IF increased with increasing d(Fe–Fe) for Fe sites, indicating a magneto-volume effect. The order of IF magnitude in Fe sites was Fe(8i)>Fe(8j)>Fe(8f) in all alloys. Co substitution for Fe sites, (Fe 0.75 Co 0.25 ), increased the IF by 25% for the R=Nd alloy and 15% for the R=Sm alloy. Decreasing Ti content from −Ti 1.0 to −Ti 0.5 , which increased the Fe and Co content, preserved the ThMn 12 structure with Zr substitution for R(2a) sites, and caused a slight increase in the IF of 2% for the R=Nd alloy and 7% for the R=Sm alloy. Nitrogenation, where N was introduced into the 2b sites, also increased IF in R=Nd alloys, by 23% for the Co- and Zr-free alloys, NdFe 11 Ti 1.0 N 1.5 , and by 7% for the Co-containing, (Nd 0.7 Zr 0.3 ) (Fe 0.75 Co 0.25 ) 11.5 Ti 0.5 N 1.3 alloy. The IF values of the R=Nd alloys were slightly larger than those of the R=Sm alloys. In conclusion, the magneto-volume effect was clearly observed at the Fe sites, and Co substitution into Fe sites and nitrogenation (R=Nd alloys) compensated for the increased IF. Increasing the Fe and Co fractions also increased IF slightly. - Highlights: • Average distances of Fe–Fe (d(Fe–Fe)) were calculated using lattice constants. • Hyperfine fields (IF) in Fe sites were measured using Mössbauer spectroscopy. • Relationship between d(Fe–Fe) and IF at each Fe site was obtained. • Co substitution and N introduction effects on IF was also measured. • Magneto-volume effect is main reason of IF augmentation in Fe sites.

Pressure-induced magnetic transition in Fe sub 4 N probed by Fe K-edge XMCD measurement

CERN Document Server

Ishimatsu, N; Maruyama, H; Kawamura, N; Suzuki, M; Ohishi, Y; Ito, M; Nasu, S; Kawakami, T

2003-01-01

X-ray magnetic circular dichroism (XMCD) of gamma'-iron nitride (Fe sub 4 N) was recorded at Fe K-edge under high pressure up to 27 GPa. The XMCD intensity decreased remarkably with pressure, and vanished at 24 GPa. Compressibility was measured by the X-ray diffraction method. These results indicate that Fe sub 4 N undergoes a second-order phase transition from the ferromagnetic state to a paramagnetic state without any structural change. The pressure-induced demagnetizing process is discussed in terms of the Fe magnetic states in the local environment.

Remoción de Fe y Mn en aguas naturales por adsorción-oxidación sobre clinoptilolita

Directory of Open Access Journals (Sweden)

Carolina Cuchimaque Lugo

2013-01-01

Full Text Available En el presente trabajo de investigación se comprueba la eficiencia en la remoción de Fe y Mn de aguas naturales por el empleo de un medio adsorbente que consiste de zeolita natural (clinoptilolita, recubierta con Fe 2O3 y MnO2 a partir de FeCl3 y MnSO4, respectivamente. La zeolita por su gran capacidad de intercambio de cationes es un excelente soporte de estos óxidos. El mecanismo de la remoción es por adsorción-oxidación de estos metales sobre la superficie de la capa de óxido que cubre el grano de zeolita. En las pruebas de remoción mediante un sistema de filtración se estudiaron las variables pH, concentraciones de Fe y Mn, caudal en el a fluente y altura de la capa de la zeolita, resultando las dos últimas ser las de mayor relevancia en la remoción. Se utilizaron concentraciones de 1,0-7,0 mg/L para Fe y de 0,5-3,0 mg/L para Mn, en un rango de pH de 6,0-8,0. La eficiencia de la remoción disminuye con el aumento en la concentración de Fe, especialmente a valores de pH altos (> 7,5, por la formación de precipitados de Fe2O3 causando aceleración en la saturación del medio. No se obtuvo una diferencia significativa sobre la remoción con el empleo de los dos tipos de recubrimiento, aunque a altas concentraciones de estos metales, con la capa de Fe 2O3 se obtuvieron porcentajes de remoción un poco mayores, pero la desventaja es que con este tipo de óxido se obtuvo menor corrida de los filtros por la saturación del medio.

Raman scattering from In0.2Ga0.8N/GaN superlattices

International Nuclear Information System (INIS)

Kisoda, Kenji; Hirakura, Kohji; Harima, Hiroshi

2006-01-01

We have performed Raman scattering experiments on high quality In 0.2 Ga 0.8 N/GaN superlattices(SLs). The A 1 LO phonon mode from the In 0.2 Ga 0.8 N layer was observed in the Mg doped SL. This was attributable to manifestation of a resonance enhancement via acceptor levels formed by magnesium doping. The peak frequency of the A 1 LO mode shifted to high frequency side with the excitation energy. The frequency shift suggested that the composition of indium was fluctuated along the growth direction in the InGaN layer. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

N2O decomposition over Fe/ZSM-5: reversible generation of highly active cationic Fe species

NARCIS (Netherlands)

Zhu, Q.; Hensen, E.J.M.; Mojet, B.L.; Wolput, van J.H.M.C.; Santen, van R.A.

2002-01-01

Fe-oxide species in Fe/ZSM-5 (prepared by chemical vapor deposition of FeCl3)-active in N2O decomposition-react with zeolite protons during high temperature calcination to give highly active cationic Fe species, this transformation being reversible upon exposure to water vapor at lower temperature

Final Report Melter Tests With AZ-101 HLW Simulant Using A Duramelter 100 Vitrification System VSL-01R10N0-1, Rev. 1, 2/25/02

International Nuclear Information System (INIS)

Kruger, A.A.; Matlack, K.S.; Kot, W.K.; Pegg, I.L.

2011-01-01

This report provides data, analyses, and conclusions from a series of tests that were conducted at the Vitreous State Laboratory of The Catholic of America (VSL) to determine the processing rates that are achievable with AZ-101 HLW simulants and corresponding melter feeds on a DuraMelter 100 (DM100) vitrification system. One of the most critical pieces of information in determining the required size of the RPP-WTP HLW melter is the specific glass production rate in terms of the mass of glass that can be produced per unit area of melt surface per unit time. The specific glass production rate together with the waste loading (essentially, the ratio of waste-in to glass-out, which is determined from glass formulation activities) determines the melt area that is needed to achieve a given waste processing rate with due allowance for system availability. Tests conducted during Part B1 (VSL-00R2590-2) on the DM1000 vitrification system installed at the Vitreous State Laboratory of The Catholic University of America showed that, without the use of bubblers, glass production rates with AZ-101 and C-106/AY-102 simulants were significantly lower than the Project design basis rate of 0.4 MT/m 2 /d. Conversely, three-fold increases over the design basis rate were demonstrated with the use of bubblers. Furthermore, an un-bubbled control test using a replica of the melter feed used in cold commissioning tests at West Valley reproduced the rates that were observed with that feed on the WVDP production melter. More recent tests conducted on the DM1200 system, which more closely represents the present RPP-WTP design, are in general agreement with these earlier results. Screening tests conducted on the DM10 system have provided good indications of the larger-scale processing rates with bubblers (for both HL W and LAW feeds) but significantly overestimated the DM1000 un-bubbled rate observed for C-106/AY-102 melter feeds. This behavior is believed to be a consequence of the role of

Neutron capture resonances in 56Fe and 58Fe in the energy range from 10 to 100 keV

International Nuclear Information System (INIS)

Kaeppeler, F.; Wisshak, K.; Hong, L.D.

1982-11-01

The neutron capture cross section of 56 Fe and 58 Fe has been measured in the energy range from 10 to 250 keV relative to the gold standard. A pulsed 3 MV Van de Graaff accelerator and the 7 Li(p, n) reaction served as a neutron source. Capture gamma rays were detected by two C 6 D 6 detectors, which were operated in coincidence and anticoincidence mode. Two-dimensional data acquisition allowed to apply the pulse height weighting technique off-line. The samples were located at a flight path of 60 cm. The total time resolution was 1.2 ns thus allowing for an energy resolution of 2 ns/m. The experimental set-up was optimized with respect to low background and low neutron sensitivity. The additional flight path of 4 cm from the sample to the detector was sufficient to discriminate capture of sample scattered neutrons by the additional time of flight. In this way reliable results were obtained even for the strong s-wave resonances of both isotopes. The experimental capture yield was analyzed with the FANAC code. The energy resolution allowed to extract resonance parameters in the energy range from 10 to 100 keV. The individual systematic uncertainties of the experimental method are discussed in detail. They were found to range between 5 and 10% while the statistical uncertainty is 3-5% for most of the resonances. A comparison to the results of other authors exhibits in case of 56 Fe systematic differences of 7-11%. For 58 Fe the present results differ up to 50% from the only other measurement for this isotope. (orig.) [de

Hot Ductility Behaviors in the Weld Heat-Affected Zone of Nitrogen-Alloyed Fe-18Cr-10Mn Austenitic Stainless Steels

Science.gov (United States)

Moon, Joonoh; Lee, Tae-Ho; Hong, Hyun-Uk

2015-04-01

Hot ductility behaviors in the weld heat-affected zone (HAZ) of nitrogen-alloyed Fe-18Cr-10Mn austenitic stainless steels with different nitrogen contents were evaluated through hot tension tests using Gleeble simulator. The results of Gleeble simulations indicated that hot ductility in the HAZs deteriorated due to the formation of δ-ferrite and intergranular Cr2N particles. In addition, the amount of hot ductility degradation was strongly affected by the fraction of δ-ferrite.

Determination of Fe, Mn and Pb by GFAAS in red wine

International Nuclear Information System (INIS)

Ying Zhecong; Jin Hua; Su Yulan

2008-01-01

A method for determination of Fe, Mn and Pb in red wine samples was developed by the graphite furnace atomic absorption spectrometric. Several different matrix modifiers were necessary because of evident analyte losses that occurred immediately in sample incineration. Red wine samples were analyzed after microwave digestion using HNO 3 . Standard addition method was used, the calibration concentration was 1 ng · ml -1 , 3 ng · ml -1 , 5 ng · ml -1 which containing 580 μg/ml KNO 3 as matrix and 0.2% HNO 3 . The correlation coefficient of the calibration line was very good within the measurement area. The recovery with red wine sample was very good at the range from 95%-107.5%. (authors)

Characterization of High Dose Mn, Fe, and Ni implantation into p-GaN

CERN Document Server

Pearton, S J; Thaler, G; Abernathy, C R; Theodoropoulou, N; Hebard, A F; Chu, S N G; Wilson, R G; Zavada, J M; Polyakov, A Y; Osinsky, A V; Norris, P E; Chow, P P; Wowchack, A M; Hove, J M V; Park, Y D

2002-01-01

The magnetization of p-GaN or p-AlGaN/GaN superlattices was measured after implantation with high doses (3-5x10 sup 1 sup 6 cm sup - sup 2) of Mn, Fe, or Ni and subsequent annealing at 700-1000 deg. C. The samples showed ferromagnetic contributions below temperatures ranging from 190-250 K for Mn to 45-185 K for Ni and 80-250 K for Fe. The use of superlattices to enhance the hole concentration did not produce any change in ferromagnetic ordering temperature. No secondary phase formation was observed by x-ray diffraction, transmission electron microscopy, or selected area diffraction pattern analysis for the doses we employed.

Data report for ROSA-IV LSTF 10% hot leg break experiment Run SB-HL-02

International Nuclear Information System (INIS)

Kukita, Yutaka; Hirata, Kazuo; Gotou, Hiroki

1990-03-01

Experimental data for the 10% hot leg break test, Run SB-HL-02, conducted at the ROSA-IV Large Scale Test Facility (LSTF) on June 30, 1987, are presented. This test assumed total failure of both high pressure injection (HPI) and auxiliary feedwater (AFW) systems. The test results were characterized by asymmetric loop responses, flashing in the cold legs and upper downcomer, as well as condensation depressurization in the cold legs following injection of emergency core coolant (ECC) from accumulators. (author)

Magnetic interactions in HoCr{sub 1-x}Fe{sub x}O{sub 3} (x = 0, 0.2) investigated by neutron powder diffraction

Energy Technology Data Exchange (ETDEWEB)

Liu, Xinzhi, E-mail: liuxinzhi1984.cn@163.com [Department of Nuclear Physics, China Institute of Atomic Energy, Beijing 102413 (China); Hao, Lijie; Ma, Xiaobai [Department of Nuclear Physics, China Institute of Atomic Energy, Beijing 102413 (China); Wang, Chin-Wei [Neutron Group, National Synchrotron Radiation Research Center, Hsinchu 30077, Taiwan (China); Klose, Frank [Australian Nuclear Science and Technology Organization, Lucas Heights, New South Wales 2234 (Australia); Department of Physics and Materials Science, The City University of Hong Kong, Hong Kong Special Administrative Region (Hong Kong); Liu, Yuntao, E-mail: ytliu@ciae.ac.cn [Department of Nuclear Physics, China Institute of Atomic Energy, Beijing 102413 (China); Sun, Kai; Li, Yuqing [Department of Nuclear Physics, China Institute of Atomic Energy, Beijing 102413 (China); Chen, Dongfeng, E-mail: dongfeng@ciae.ac.cn [Department of Nuclear Physics, China Institute of Atomic Energy, Beijing 102413 (China)

2017-07-01

Highlights: • The temperature dependent magnetism of HoCr{sub 1-x}Fe{sub x}O{sub 3} (x = 0, 0.2) were investigated by neutron diffraction. • Cr{sup 3+} moment follows a mean field theory while Ho{sup 3+} follows a spin 1/2 model. • An magneto-elastic strain was observed accompanying with the ordering of Cr{sup 3+}. - Abstract: The temperature dependent magnetism of Fe-doped rare earth orthochromite HoCr{sub 1-x}Fe{sub x}O{sub 3}(x = 0, 0.2) was investigated by neutron powder diffraction. It is found that the magnetism of Cr(Fe){sup 3+} can be well understood within mean field theory, while the ordering of Ho{sup 3+} was induced by the Cr(Fe){sup 3+} sublattice and can be satisfyingly described by an effective S = 1/2 model. The absences of both the most common G{sub x}F{sub z} configuration of Cr{sup 3+} and the ordering of Ho{sup 3+} caused by Ho-Ho interaction evidence a strong Ho{sup 3+}-Cr{sup 3+} interaction which dominates this system. On the other hand, a remarkable magnetoelastic strain was observed accompanying the Cr(Fe){sup 3+} ordering. An analysis based on the equation of state with a Grüneisen approximation was performed and revealed magnetic origin of this strain.

Extreme Field Sensitivity of Magnetic Tunneling in Fe-Doped Li_{3}N.

Science.gov (United States)

Fix, M; Atkinson, J H; Canfield, P C; Del Barco, E; Jesche, A

2018-04-06

The magnetic properties of dilute Li_{2}(Li_{1-x}Fe_{x})N with x∼0.001 are dominated by the spin of single, isolated Fe atoms. Below T=10  K the spin-relaxation times become temperature independent indicating a crossover from thermal excitations to the quantum tunneling regime. We report on a strong increase of the spin-flip probability in transverse magnetic fields that proves the resonant character of this tunneling process. Longitudinal fields, on the other hand, lift the ground-state degeneracy and destroy the tunneling condition. An increase of the relaxation time by 4 orders of magnitude in applied fields of only a few milliTesla reveals exceptionally sharp tunneling resonances. Li_{2}(Li_{1-x}Fe_{x})N represents a comparatively simple and clean model system that opens the possibility to study quantum tunneling of the magnetization at liquid helium temperatures.

(CaFeAs){sub 10}Pt{sub z}As{sub 8} superconductors and related compounds

Energy Technology Data Exchange (ETDEWEB)

Stuerzer, Tobias

2015-04-13

The main topic of this dissertation is the identification of new compounds, structure determination, and substitution dependent investigation of properties in this new branch of the family of iron arsenide superconductors (Chapter 2). Chapter 2.1 presents the identification of the superconducting compounds and the corresponding structure elucidation identifying two dif-ferent species (CaFeAs){sub 10}Pt{sub 3}As{sub 8} and (CaFeAs){sub 10}Pt{sub 4}As{sub 8} in this family (abbreviated as 1038 and 1048 according to their stoichiometry). However, a closer look revealed a more challenging structure chemistry which is covered in Chapter 2.2. The following two Chapters 2.3 and 2.4 are devoted to (CaFeAs){sub 10}Pt{sub 3}As{sub 8} and more detailed investigations on this parent compound of the new superconductor family. Furthermore, transition metal substitution series (CaFe{sub 1-x}M{sub x}As){sub 10}Pt{sub 3}As{sub 8} were synthesized to investigate the resemblance to model systems Ba(Fe{sub 1-x}M{sub x}){sub 2}As{sub x} and LaO(Fe{sub 1-x}M{sub x})As in the scope of structural changes and superconductivity as described in Chapter 2.5. Initially amazing differences in superconducting properties com-paring 1038 and 1048 compounds are analyzed in Chapter 2.6 establishing an universal dop-ing model in the (CaFe{sub 1-x}M{sub x}As){sub 10}Pt{sub z}As{sub 8} family. Additionally substituent dependent properties upon rare earth substitution in electron doped (Ca{sub 1-y}RE{sub y}FeAs){sub 10}Pt{sub 3}As{sub 8} are investigated in Chapter 2.7, while a detailed study of superconducting properties and magnetism in (Ca{sub 1-y}La{sub y}FeAs){sub 10}Pt{sub 3}As{sub 8} by the local μSR technique is presented in Chapter 2.8. In Chapter 2.9 a comparison of direct and electron doping is discussed based on codoping experiments in (Ca{sub 1-y}La{sub y}Fe{sub 1-x}Pt{sub x}As){sub 10}Pt{sub 3}As{sub 8} and (CaFe{sub 1-x}Pt{sub x}As){sub 10}Pt{sub 4}As{sub 8}. Finally, in Chapter 2.10

Transport properties and exponential n-values of Fe/MgB2 tapes with various MgB2 particle sizes

International Nuclear Information System (INIS)

Lezza, P.; Abaecherli, V.; Clayton, N.; Senatore, C.; Uglietti, D.; Suo, H.L.; Fluekiger, R.

2004-01-01

Fe/MgB 2 tapes have been prepared starting with pre-reacted binary MgB 2 powders. As shown by resistive and inductive measurements, the reduction of particle size to a few microns by ball milling has little influence on B c2 , while the superconducting properties of the individual MgB 2 grains are essentially unchanged. Reducing the particle size causes an enhancement of B irr from 14 to 16 T, while J c has considerably increased at high fields, its slope J c (B) being reduced. At 4.2 K, values of 5.3 x 10 4 and 1.2 x 10 3 A/cm 2 were measured at 3.5 and 10 T, respectively, suggesting a dominant role of the conditions at the grain interfaces. A systematic variation of these conditions at the interfaces is undertaken in order to determine the limit of transport properties for Fe/MgB 2 tapes. The addition of 5% Mg to MgB 2 powder was found to affect neither J c nor B c2 . For the tapes with the highest J c values, very high exponential n factors were measured: n=148, 89 and 17 at 3.5, 5 and 10 T, respectively and measurements of critical current versus applied strain have been performed. The mechanism leading to high transport critical current densities of filamentary Fe/MgB 2 tapes based on MgB 2 particles is discussed

PRODUCCIÓN DE UNA ALEACIÓN NANOESTRUCTURADA FeAl MEDIANTE ALEACIÓN MECÁNICA Y SU CARACTERIZACIÓN MICROESTRUCTURAL

Directory of Open Access Journals (Sweden)

Roberto. A. Rodríguez-Díaz

2013-01-01

Full Text Available En este trabajo se elaboró la aleación Fe40Al mediante la técnica de aleación mecánica (AM a partir de una mezcla de polvos elementales de Fe y Al, empleando distintos tiempos de molienda. Se caracterizó la evolución en tamaño y morfología de los polvos empleados en el proceso de AM en función del tiempo de molienda mediante la técnica de Microscopía Electrónica de Barrido (MEB. Se empleó la técnica de Difracción de Rayos X (DRX para caracterizar la evolución de la estructura cristalina de las fases obtenidas en función del tiempo de molienda. La aleación Fe40Al con estructura cristalina desordenada del tipo cúbico centrado en el cuerpo se formó a las 20 h de molienda. El tamaño nano-métrico de grano correspondiente a la aleación desordenada Fe40Al se redujo con el transcurso del tiempo mientras que su parámetro de red se incrementó con el transcurso del tiempo de molienda.

Polaronic transport and thermoelectricity in Fe1 -xCoxSb2S4 (x =0 , 0.1, and 0.2)

Science.gov (United States)

Liu, Yu; Kang, Chang-Jong; Stavitski, Eli; Du, Qianheng; Attenkofer, Klaus; Kotliar, G.; Petrovic, C.

2018-04-01

We report a study of Co-doped berthierite Fe1 -xCoxSb2S4 (x =0 , 0.1, and 0.2). The alloy series of Fe1 -xCoxSb2S4 crystallize in an orthorhombic structure with the Pnma space group, similar to FeSb2, and show semiconducting behavior. The large discrepancy between activation energy for conductivity, Eρ (146 ˜270 meV ), and thermopower, ES (47 ˜108 meV ), indicates the polaronic transport mechanism. Bulk magnetization and heat-capacity measurements of pure FeSb2S4 (x =0 ) exhibit a broad antiferromagnetic transition (TN=46 K ) followed by an additional weak transition (T*=50 K ). Transition temperatures (TN and T*) slightly decrease with increasing Co content x . This is also reflected in the thermal conductivity measurement, indicating strong spin-lattice coupling. Fe1 -xCoxSb2S4 shows relatively high value of thermopower (up to ˜624 μ V K-1 at 300 K) and thermal conductivity much lower when compared to FeSb2, a feature desired for potential applications based on FeSb2 materials.

Two S-wave gap symmetry for single crystals of the superconductor BaFe1.8Co0.2As2

International Nuclear Information System (INIS)

Choi, Ki-Young; Kim, Soo Hyun; Choi, Changho; Jung, Myung-Hwa; Wang, X.F.; Chen, X.H.; Noh, Jae Dong; Lee, Sung-IK

2010-01-01

To clarify the gap structure of the iron-pnictide superconductors, we synthesized optimally doped single crystals of BaFe 1.8 Co 0.2 As 2 , which had a critical temperature, T c , of 23.6 K. The initial M-H curve was used to find the lower critical field, H c1 . The full range of the temperature dependence of H c1 was explained by using a two S-wave gap symmetry. We estimate the two gap as Δ 1 (0) = 1.64 ± 0.2 meV for the small gap and Δ 2 (0) = 6.20 ± 0.2 meV for the large gap.

Production of 26Al by spallation of Fe, Si, Al nuclei

International Nuclear Information System (INIS)

Paillard, P.

1977-01-01

Cross sections for 7 Be, 10 Be and 26 Al formation in Al, Si and Fe targets bombarded with 0.6 and 24GeV protons have been measured by using highly selective chemical separation and low level background counters. Results for 26 Al at 0.6GeV are in mb: 17.9 + or - 2.7 in Al, 12.5 + or - 2.5 in Si and 0.45 + or - 0.14 in Fe; at 24GeV 2.6 + or - 0.5mb in Fe. Results for 10 Be are not valid on account of experimental difficulties. It is deduced from these values of aluminium in cosmic ray propagation that 26 Al is not yet cosmic ray chronometer [fr

A high sensitive biosensor based on FePt/CNTs nanocomposite/N-(4-hydroxyphenyl)-3,5-dinitrobenzamide modified carbon paste electrode for simultaneous determination of glutathione and piroxicam.

Science.gov (United States)

Karimi-Maleh, Hassan; Tahernejad-Javazmi, Fahimeh; Ensafi, Ali A; Moradi, Reza; Mallakpour, Shadpour; Beitollahi, Hadi

2014-10-15

This study describes the development, electrochemical characterization and utilization of novel modified N-(4-hydroxyphenyl)-3,5-dinitrobenzamide-FePt/CNTs carbon paste electrode for the electrocatalytic determination of glutathione (GSH) in the presence of piroxicam (PXM) for the first time. The synthesized nanocomposite was characterized with different methods such as TEM and XRD. The modified electrode exhibited a potent and persistent electron mediating behavior followed by well-separated oxidation peaks of GSH and PXM. The peak currents were linearly dependent on GSH and PXM concentrations in the range of 0.004-340 and 0.5-550 µmol L(-1), with detection limits of 1.0 nmol L(-1) and 0.1 µmolL(-1), respectively. The modified electrode was successfully used for the determination of the analytes in real samples with satisfactory results. Copyright © 2014 Elsevier B.V. All rights reserved.

Chemical products toxicological tests performed on lake and river fish

International Nuclear Information System (INIS)

Teulon, F.; Simeon, C.

1966-01-01

The volume and toxical values of industrial and urban effluents are growing higher and therefore acute or chronic pollution hazard is proportionally increased. Hence it is necessary to determine the effluent components minimum lethal dose for fish (one hour or six hours according to applicable standards). The following tests are described in this report: toxicity of some chemical products, tested individually (sodium, sulphate, sodium chloride, sodium fluoride, etc...); toxicity of some metal ions (Al 3+ , Fe ++ , Fe 3+ , Pb ++ , etc...); toxicity of certain mixed compounds for various fish species (sun perch, tench, gold fish, roach, gudgeon, bleak). The test results obtained represent local values and may be used for reference and as a general basis for other investigation and calculation of the effluents data when released. (author) [fr

Determination of micro mineral Fe on cow meat and liver

International Nuclear Information System (INIS)

Natalia Adventini; Muhayatun; Syukria Kurniawati; Endang; Yuni Setyowat

2010-01-01

Fe deficiency is common in development countries. Fe deficiency could decreased the IQ level, immune function and work performance, impacts decreasing human resource quality. Beef and liver are Fe source which more easily absorbed compare to Fe found in plant products. Therefore, the Fe determination in beef and liver need to be carried out using INAA. Instrumental neutron activation analysis is a method for qualitative and quantitative determination of elements based on the measurement of characteristic radiation from radionuclide formed by neutron irradiation of the material. The Sixteen beef and liver from feed treatment cows were collected. Method validation using RM IAEAA-13 gave accuracy and precise were 99 % and 3,3 % respectively. Fe concentration in 16 beef and liver were obtained between 5.5-18.6 mg/kg wet weight with average value was 12.2±4.0 mg/kg and 22.9-4.7 mg/kg with average value was 35.2±8.7 mg/kg. Generally, this value gave the same result from other countries. Fe determination in beef and liver is not only expected to be a scientific based reference but also to update Indonesia food stuff composition data. (author)

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of Cr, Fe, Cu, Zn and Se in cereals

Science.gov (United States)

Huang, Shih-Yi; Jiang, Shiuh-Jen; Sahayam, A. C.

2014-11-01

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Cr, Fe, Cu, Zn and Se in several cereal samples. Thioacetamide was used as the modifier to enhance the ion signals. The background ions at the masses of interest were reduced in intensity significantly by using 1.0 mL min- 1 methane (CH4) as reaction cell gas in the dynamic reaction cell (DRC). Since the sensitivities of Cr, Fe, Cu, Zn and Se in different matrices were quite different, standard addition and isotope dilution methods were used for the determination of Cr, Fe, Cu, Zn and Se in these cereal samples. The method detection limits estimated from standard addition curves were about 1, 10, 4, 12 and 2 ng g- 1 for Cr, Fe, Cu, Zn and Se, respectively, in original cereal samples. This procedure has been applied to the determination of Cr, Fe, Cu, Zn and Se whose concentrations are in μg g- 1 (except Cr and Se) in standard reference materials (SRM) of National institute of standards and technology (NIST), NIST SRM 1568a Rice Flour and NIST SRM 1567a Wheat Flour and two cereal samples purchased from a local market. The analysis results of reference materials agreed with certified values at 95% confidence level according to Student's T-test. The results for the real world cereal samples were also found to be in good agreement with the pneumatic nebulization DRC ICP-MS results of the sample solutions.

FINAL REPORT MELTER TESTS WITH AZ-101 HLW SIMULANT USING A DURAMELTER 100 VITRIFICATION SYSTEM VSL-01R10N0-1 REV 1 2/25/02

Energy Technology Data Exchange (ETDEWEB)

KRUGER AA; MATLACK KS; KOT WK; PEGG IL

2011-12-29

This report provides data, analyses, and conclusions from a series of tests that were conducted at the Vitreous State Laboratory of The Catholic of America (VSL) to determine the processing rates that are achievable with AZ-101 HLW simulants and corresponding melter feeds on a DuraMelter 100 (DM100) vitrification system. One of the most critical pieces of information in determining the required size of the RPP-WTP HLW melter is the specific glass production rate in terms of the mass of glass that can be produced per unit area of melt surface per unit time. The specific glass production rate together with the waste loading (essentially, the ratio of waste-in to glass-out, which is determined from glass formulation activities) determines the melt area that is needed to achieve a given waste processing rate with due allowance for system availability. Tests conducted during Part B1 (VSL-00R2590-2) on the DM1000 vitrification system installed at the Vitreous State Laboratory of The Catholic University of America showed that, without the use of bubblers, glass production rates with AZ-101 and C-106/AY-102 simulants were significantly lower than the Project design basis rate of 0.4 MT/m{sup 2}/d. Conversely, three-fold increases over the design basis rate were demonstrated with the use of bubblers. Furthermore, an un-bubbled control test using a replica of the melter feed used in cold commissioning tests at West Valley reproduced the rates that were observed with that feed on the WVDP production melter. More recent tests conducted on the DM1200 system, which more closely represents the present RPP-WTP design, are in general agreement with these earlier results. Screening tests conducted on the DM10 system have provided good indications of the larger-scale processing rates with bubblers (for both HL W and LAW feeds) but significantly overestimated the DM1000 un-bubbled rate observed for C-106/AY-102 melter feeds. This behavior is believed to be a consequence of the role of

Correlation between the nanocrystalline Sm(Fe,Mo){sub 12} and its out of equilibrium phase Sm(Fe,Mo){sub 10}

Energy Technology Data Exchange (ETDEWEB)

Khazzan, S. [CMTR, ICMPE, UMR7182, CNRS - Université Paris Est, 2-8 rue Henri Dunant, F-94320 Thiais (France); Laboratoire Matériaux Organisation et Propriétés, Faculté des Sciences de Tunis, Université de Tunis El Manar, 2092 Tunis (Tunisia); Bessais, L., E-mail: bessais@glvt.cnrs.fr [CMTR, ICMPE, UMR7182, CNRS - Université Paris Est, 2-8 rue Henri Dunant, F-94320 Thiais (France); Van Tendeloo, G. [EMAT, University of Antwerp, B-2020 Antwerp (Belgium); Mliki, N. [Laboratoire Matériaux Organisation et Propriétés, Faculté des Sciences de Tunis, Université de Tunis El Manar, 2092 Tunis (Tunisia)

2014-08-01

Nanostructured Sm–Fe–Mo semi-hard magnetic material exhibiting enhanced magnetic properties can be produced by ball milling followed by recrystallization. Milled samples were annealed for 30 min in a vacuum at different temperatures (T{sub A}) between 700 and 1190 °C. The effects of heat treatment and Mo content on structural and magnetic property changes have been investigated by means of X-ray diffraction using the Rietveld method, transmission electron microscopy and magnetic measurements. For samples annealed at T{sub A}>900°C the tetragonal ThMn{sub 12}-type structure is identified, while for 700determined on the basis of the vacancy model. The Rietveld analysis gives a stoichiometry ratio equal to 1:10, for the out of equilibrium hexagonal phase, which is described with three crystallographic transition metal sites: 3g is fully occupied, 6l occupation is limited to hexagons surrounding the Fe dumbbell pairs 2e. We have performed a magnetic and structural study of nanocrystalline metastable P6/mmm Sm(Fe{sub 1−x}Mo{sub x}){sub 10}, correlated with structural transformation towards its equilibrium derivative I4/mmm Sm(Fe{sub 1−x}Mo{sub x}){sub 12}. A maximum of the coercive field H{sub C} (H{sub C}>5kOe) has been observed for the new hexagonal P6/mmm phase suggesting that nanocrystalline Sm(Fe,Mo){sub 10}, is a semi-hard material, and is potential candidate for magnetic recording. - Highlights: • A study of the structure and magnetic properties of SmFeMo compound. • A new out of equilibrium P6/mmm-type structure was found. • Correlation between the 1/12 phase and its out of equilibrium 1/10 phase.

Highly selective spectrophotometric determination of trace amounts of vanadium(V) with 2-(8-quinolylazo)-5-N,N-diethylaminophenol by reversed-phase partition liquid chromatography

International Nuclear Information System (INIS)

Hoshino, Hitoshi; Yotsuyanagi, Takao

1982-01-01

A novel reversed-phase partition liquid chromatography-photometric detection system for the determination of trace amounts of vanadium is described. A strongly colored vanadium(V)-2-(8-quinolylazo)-5-N,N-diethylaminophenolato chelate is separated on a μBondapak-CN column using an aqueous acetonitrile mobile phase and is detected at 540 nm(0.02 absorbance unit full-scale). Because the other common cations give no resolved peaks on the chromatogram under the conditions, the determination of vanadium at 5 x 10 -8 to 1 x 10 -6 mol dm -3 level is free from their interferences in case of the total concentration of such cations less than 5 x 10 -5 mol dm -3 (author)

High Performance Fe- and N- Doped Carbon Catalyst with Graphene Structure for Oxygen Reduction

Science.gov (United States)

Peng, Hongliang; Mo, Zaiyong; Liao, Shijun; Liang, Huagen; Yang, Lijun; Luo, Fan; Song, Huiyu; Zhong, Yiliang; Zhang, Bingqing

2013-05-01

Proton exchange membrane fuel cells are promising candidates for a clean and efficient energy conversion in the future, the development of carbon based inexpensive non-precious metal ORR catalyst has becoming one of the most attractive topics in fuel cell field. Herein we report a Fe- and N- doped carbon catalyst Fe-PANI/C-Mela with graphene structure and the surface area up to 702 m2 g-1. In 0.1 M HClO4 electrolyte, the ORR onset potential for the catalyst is high up to 0.98 V, and the half-wave potential is only 60 mV less than that of the Pt/C catalyst (Loadings: 51 μg Pt cm-2). The catalyst shows high stability after 10,000 cyclic voltammetry cycles. A membrane electrode assembly made with the catalyst as a cathode is tested in a H2-air single cell, the maximum power density reached ~0.33 W cm2 at 0.47 V.

Carbonate component reduces o,oEDDHA/Fe sorption on two-line ferrihydrite

Science.gov (United States)

Yunta, F.; Lucena, J. J.; Smolders, E.

2012-04-01

The o,oEDDHA/Fe is the most common and effective iron chelate used as fertilizer in calcareous soils. Several authors have reported that the anionic o,oEDDHA/Fe complex is adsorbed to soil components such as ferrihydrite. The bicarbonate anion may be a competing ion for this sorption, however no studies have yet identified the extent and mechanism of this interaction. The aim of this work was to study the carbonate (bicarbonate + carbonate) effect on EDDHA/Fe adsorption on two-line ferrihydrite. Two-line ferrihydrite was synthetized adding NaOH on a nitrate iron (III) solution up to a final pH to be 8.0 and allowing to age for 22 hours at 20°C. Dialyzed ferrihydrite was characterized by determining specific parameters such as Fe/OH ratio, BET surface, point zero of charge and x-ray diffraction. The sorption was performed at three pH levels (5, 7.5 and 9.5) and three initial carbonate concentrations (from 0 to 2 mM). Initial EDDHA/Fe, ferrihydrite and ionic strength concentrations were adjusted to 0.18 mM, 10 g L-1 and 5 mM respectively. Total dissolved FeEDDHA concentrations were quantified at 480 nm. The o,oEDDHA/Fe isomers (rac-o,oEDDHA/Fe and meso-o,oEDDHA/Fe) were separated and quantified by High Performance Liquid Chromatography (HPLC) fitting a photodiode array detector (PDA). Distribution factor (KD) and sorbed o,oEDDHA/Fe concentration were determined. Actual carbonate concentration was determined using a multi N/C analyzer. Ferrihydrite samples showed a typical XRD pattern of two-line ferrihydrite, two broad peaks at about 35 and 62° respectively. The BET surfaces (two replicates) were 259.2 ± 3.1 m2/g and 256.0 ± 2.5 m2/g. The Point Zero of Salt Effect (PZSE) was 7.9 ± 0.2 as bibliographically supported for all fresh and thus not rigorously de-carbonated ferrihydrite samples. The KD of the o,oEDDHA/Fe increased from 27.4 ± 0.6 to 304 ± 6 l/kg by decreasing pH from 9.5 and 5.0 when no carbonate was added. Increasing equilibrium carbonate

N/S/B-doped graphitized carbon encased Fe species as a highly active and durable catalyst towards oxygen reduction reaction.

Science.gov (United States)

Li, Guang-Lan; Cheng, Guang-Chun; Chen, Wen-Wen; Liu, Cai-Di; Yuan, Li-Fang; Yang, Bei-Bei; Hao, Ce

2018-03-15

Exploring cost-effective, high-performance and durable non-precious metal catalysts is of great significance for the acceleration of sluggish oxygen reduction reaction (ORR). Here, we report an intriguing heteroatom-doped graphitized carbon encased Fe species composite by introducing N, S and B sequentially. The experimental approach was designed ingeniously for that the FeCl 3 ·6H 2 O could catalyze thiourea to synthesize N, S co-doped carbon materials which would further react with H 3 BO 3 and NH 3 (emerged at the heat-treatment process) to prepare N, S and B co-doped carbon materials (Fe-N/S/B-C). The Fe-N/S/B-C exhibits an impressive ORR activity for its half-wave potential of -0.1 V, which is 36 mV or 19 mV higher than that of the corresponding single or dual doped counterparts (Fe-N-C or Fe-N/S-C) and 31 mV positive than that of Pt/C catalyst, respectively. Further chronoamperometric measurement and accelerated aging test confirm the excellent electrochemical durability of Fe-N/S/B-C with the stable core-shell structure. The remarkable ORR performance and facile preparation method enable Fe-N/S/B-C as a potential candidate in electrochemical energy devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Ferromagnetic resonance of facing-target sputtered epitaxial γ‧-Fe4N films: the influence of thickness and substrates

Science.gov (United States)

Lai, Zhengxun; Li, Zirun; Liu, Xiang; Bai, Lihui; Tian, Yufeng; Mi, Wenbo

2018-06-01

The microstructure and high frequency properties of facing-target sputtered epitaxial γ‧-Fe4N films were investigated in detail. It was found that the eddy current in ultrathin γ‧-Fe4N films is too small to influence the ferromagnetic resonance (FMR) linewidth, where the linewidth is mostly determined by intrinsic damping and the two-magnon scattering (TMS) process. In relatively thick films, the TMS process can significantly affect the linewidth due to the roughness on the sample surface. However, the TMS process in a thin film is quite weak because of its smooth surface. The Gilbert damping constant of about 0.0135 in our γ‧-Fe4N films is smaller than the experimental value in the previous work. Moreover, substrates can also influence the FMR linewidth of the γ‧-Fe4N films by the TMS process. Besides, the resonance field of polycrystalline γ‧-Fe4N film is larger than the epitaxial ones because of the lack of a magnetic anisotropic field, but the linewidth of the polycrystalline γ‧-Fe4N film is smaller.

Comparison in the electronic structure of YBa{sub 2}Fe{sub 3}O{sub 8} insulator with YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} superconductors

Energy Technology Data Exchange (ETDEWEB)

Zhang, Y.; Guan, X.Y. [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); Cheng, C.H. [School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Pan, M. [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); Zhang, H. [Department of Physics, Peking University, Beijing 100871 (China); Zhao, Y., E-mail: yzhao@home.swjtu.edu.cn [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia)

2013-10-15

Highlights: • The electronic structure of YBa{sub 2}Fe{sub 3}O{sub 8}, YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} were investigated by XPS. • The core-level and valence-band structures of these systems are different. • The density of states at Fermi level is related to the superconductivity. -- Abstract: The electronic structure and chemical states of relevant elements of YBa{sub 2}Fe{sub 3}O{sub 8} are investigated using X-ray photoemission spectroscopy (XPS), compared with those of YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} superconductors. The typical differences and similarities in core-level and valence-band structures of these systems have been detected, strongly suggesting that the superconductivity have the finite density of states around Fermi level. Several features of O1s, Y3d, Ba3d, and Fe2p core lines in XPS spectra are also carefully compared and analyzed.

Electron spin resonance of Fe4+ in amethyst quartz

International Nuclear Information System (INIS)

Cox, R.T.

1975-01-01

The ESR spectrum of Fe 4+ was looked for in amethyst quartz. Besides saturated Fe 3+ lines, ESR lines of a new paramagnetic center whose spin-lattice relaxation time is relatively short were observed. They could be attributed to Fe 4+ [fr

Andreev spectroscopy of FeSe{sub x}Te{sub 1−x}

Energy Technology Data Exchange (ETDEWEB)

Fujioka, Naoya, E-mail: f-naoya@moegi.waseda.jp; Shirai, Yoshiki; Miyamoto, Yukihiro; Tachibana, Hironori; Matsuda, Azusa

2015-11-15

Highlights: • We fabricated FeSe{sub 0.2}Te{sub 0.8}/oxide/Pb and FeSe{sub 0.2}Te{sub 0.8}/Al/Al{sub 2}O{sub 3}/Pb junctions. • These junctions show anomalous conductance spectra and no Josephson current. • These spectra are explained by S/N interface model with extraordinarily gaps. • Except for anomalous gap values, the result is consistent with s+− symmetry. - Abstract: We fabricated two types of junctions on the c-axis plane of FeSe{sub 0.2}Te{sub 0.8} (Fe[Se,Te], T{sub c} ∼ 13 K) crystals. In the superconductor/oxide/superconductor heterojunctions with a Pb film as a counter electrode, we found a large conductance peak centered at 0 V, and a gap-like feature, which has a much higher energy scale than those reported as a gap energy of Fe[Se,Te]. In spite of a large energy scale, their temperature dependence approximately follows a BCS curve, indicating they come from superconductivity of Fe[Se,Te]. Since these structures can be understood as the results of Andreev bound state at the S/N boundary and the interference effect in the normal metal [1], we tried to identify the effect of a normal layer by fabricating Fe[Se,Te]/Al/Al{sub 2}O{sub 3}/Pb junction. Here, we could realize a clean controlled S/N interface and the tunnel junction to investigate electronic properties of the Al slab. We found similar conductance spectra as those junctions without Al layer, giving a support that the anomalous conductance spectra come from the effect of the S/N interface. As expected, the energy scale of the observed features was reduced when the thickness of the normal metal was increased. The absence of Josephson current and the existence of an Andreev bound state may be a signature of the sign-reversal paring in Fe[Se,Te].

Highly active La0.4Sr0.6Co0.8Fe0.2O3-δ nanocatalyst for oxygen reduction in intermediate temperature-solid oxide fuel cells

Science.gov (United States)

Chanquía, Corina M.; Mogni, Liliana; Troiani, Horacio E.; Caneiro, Alberto

2014-12-01

Pure-phase La0.4Sr0.6Co0.8Fe0.2O3-δ (LSCF) nanocrystallites were successfully synthesized by the combustion method, by employing glycine as fuel and complexing agent, and ammonium nitrate as combustion trigger. The morphological and structural characterization of the LSCF nanopowders was performed by using X-ray diffraction, N2 physisorption and electron microscopy. The LSCF nanopowder consists of interconnected nanocrystallites (∼45 nm) forming a sponge-like structure with meso and macropores, being its specific surface area around 10 m2 g-1. Crystalline structural analyses show that the LSCF nanopowder presents cubic symmetry in the Pm-3m space group. By employing the spin coating technique and different thermal treatments, symmetrical cells with different electrode crystallite size (45 and 685 nm) were built, by using La0.8Sr0.2Ga0.8Mg0.2O3-δ as electrolyte. Electrochemical impedance spectroscopy measurements were performed varying temperature and pO2. The area specific resistance of the nanostructured sample (45 nm) decreases by two orders of magnitude with respect to the submicrostructured sample (685 nm), reaching values as low as 0.8 Ω cm2 at 450 °C. This improvement is attributed to the cathode morphology optimization in the nanoscale, i.e., enlargement of the exposed surface area and shortening of the oxygen diffusion paths, which reduce the polarization resistance associated to the surface exchange and O-ion bulk diffusion process.

Microstructure and Mechanical Properties of n-irradiated Fe-Cr Model Alloys

International Nuclear Information System (INIS)

Matijasevic, Milena; Al Mazouzi, Abderrahim

2008-01-01

High chromium ( 9-12 wt %) ferritic/martensitic steels are candidate structural materials for future fusion reactors and other advanced systems such as accelerator driven systems (ADS). Their use for these applications requires a careful assessment of their mechanical stability under high energy neutron irradiation and in aggressive environments. In particular, the Cr concentration has been shown to be a key parameter to be optimized in order to guarantee the best corrosion and swelling resistance, together with the least embrittlement. In this work, the characterization of the neutron irradiated Fe-Cr model alloys with different Cr % with respect to microstructure and mechanical tests will be presented. The behavior of Fe-Cr alloys have been studied using tensile tests at different temperature range ( from -160 deg. C to 300 deg. C). Irradiation-induced microstructure changes have been studied by TEM for two different irradiation doses at 300 deg. C. The density and the size distribution of the defects induced have been determined. The tensile test results indicate that Cr content affects the hardening behavior of Fe-Cr binary alloys. Hardening mechanisms are discussed in terms of Orowan type of approach by correlating TEM data to the measured irradiation hardening. (authors)

Evaluation of 54Fe(n,2n)53m+gFe reaction cross sections for high energy dosimetry applications

International Nuclear Information System (INIS)

Zolotarev, K.I.; Pashchenko, A.B.

2001-01-01

The new evaluation of excitation function for the high energy threshold 54 Fe(n,2n) 53m+g Fe dosimetry reaction in the energy range from the threshold to 20 MeV is briefly described. The cross section uncertainties and the covariance matrix were estimated simultaneously from the analysis. The adopted curve is compared to the available processed experimental data and the existing FEI-93, ENDF/B-VI and JENDL-3.2 evaluations. The ENDF-6 formatted data file is available from the Web site of the Russian Nuclear Data Center (RNDC) online (http://www.rndc.ippe.obninsk.ru). (author)

Synthesis of peptide templated copper nanoclusters for fluorometric determination of Fe(III) in human serum

International Nuclear Information System (INIS)

Tang, Ting; Ouyang, Jiang; Hu, Lanshuang; Guo, Linyan; Yang, Minghui; Chen, Xiang

2016-01-01

Copper nanoclusters (Cu-NCs) were prepared by reducing CuCl 2 with ascorbic acid in the presence of the short peptide template Cys-Cys-Cys-Asp-Leu. They were characterized by UV-vis absorption and fluorescence spectroscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The Cu-NCs have a size of ∼2 nm, can be well dispersed in water and are photostable. Their fluorescence (peaking at 425 nm under 365-nm excitation) is quenched by Fe(III) ions. Based on this finding, a sensitive and selective fluorescence assay for the detection of Fe(III) was developed. Under optimized conditions and a pH value of 2.0, the assay displays a linear response in the 0.05 to 30 μM Fe(III) concentration range, with a detection limit of 20 nM based on an S/N ratio of 3. The assay was successfully applied to the determination of Fe(III) in spiked human serum where is gave recoveries that ranged from 96.2 % to 98.3 %. (author)

Nano assembly of N-doped graphene quantum dots anchored Fe3O4/halloysite nanotubes for high performance supercapacitor

International Nuclear Information System (INIS)

Ganganboina, Akhilesh Babu; Chowdhury, Ankan Dutta; Doong, Ruey-an

2017-01-01

Highlights: •Halloysite coated Fe 3 O 4 is served as the framework for supporting graphene quantum dots. •GQDs can be well distributed onto Fe 3 O 4 /HNTs to prevent structural failure. •High specific capacitance of 418 F g −1 in 1 M Na 2 SO 4 neutral electrolyte is observed. •The composites show excellent electrochemical performance with energy density of 10.4–29.0 Wh kg −1 . -- Abstract: The development of robust and low cost electrode materials with superior electrochemical properties has been a subject of focus on energy storage devices. Herein, the development of N-doped graphene quantum dots (N-GQDs) deposited on Fe 3 O 4 -halloysite nanotubes (Fe 3 O 4 -HNTs) as active anode materials has been established for supercapacitor applications. The Fe 3 O 4 nanoparticles synthesised by coprecipitation have been in-situ deposited on HNT surfaces following by the coating of (3-aminopropyl)-triexthoxysilane to anchor 4–10 nm N-GQDs via the formation of amide linkage. The N-GQD@Fe 3 O 4 -HNTs exhibits a high specific capacitance of 418 F g −1 and maintains good rate capability in neutral electrolyte solutions. In addition, the anode materials show excellent electrochemical performance with energy and power densities of 10.4–29 W h kg −1 and 0.25–5.2 kW kg −1 , respectively. Such excellent electrochemical features can be attributed to the synergistic contribution from individual components. The Fe 3 O 4 -HNTs provide 1-dimensional matrix to shorten the diffusion path of electrons and electrolyte ions as well as to absorb the mechanical stress during cycling along with excess sites for charge storage, while N-GQDs offer abundantly accessible electroactive sites for rapid electrons and electrolyte ions transport as well as enhance electrical conductivity of Fe 3 O 4 -HNTs. Results obtained in this study clearly demonstrate that metal oxide-HNTs are promising support to anchor N-GQDs nanomaterials as the high performance anode materials for next

TEM study on a new Zr-(Fe, Cu) phase in furnace-cooled Zr-1.0Sn-0.3Nb-0.3Fe-0.1Cu alloy

Science.gov (United States)

Liu, Yushun; Qiu, Risheng; Luan, Baifeng; Hao, Longlong; Tan, Xinu; Tao, Boran; Zhao, Yifan; Li, Feitao; Liu, Qing

2018-06-01

A new Zr-(Fe, Cu) phase was found in furnace-cooled Zr-1.0Sn-0.3Nb-0.3Fe- 0.1Cu alloy and alloys aged at 580 °C for 10min, 2 h and 10 h. Electron diffraction experiment shows the crystal structure of this phase to be body-centered tetragonal with unit cell dimensions determined to be a = b = 6.49 Å, c = 5.37 Å. Its possible space groups have been discussed and the reason accounting for its formation is believed to be the addition of Cu according to the atom-level images. In addition, no crystal structural or chemical composition changes were observed throughout the aging process.

A fast and very sensitive LSC procedure to determine Fe-55 in steel and concrete

International Nuclear Information System (INIS)

Koenig, W.; Schupfner, R.; Schuettelkopf, H.

1995-01-01

This procedure determining Fe-55 contributes to a safe and economically reasonable decommissioning of nuclear power plants. Co-60, Fe-55 and Ni-63 are the most abundant, long-lived radionuclides associated with contaminated piping, hardware, and concrete for several decades of years after shutdown. The analysis of Fe takes about three hours until the measurement with an anticoincidence shielded LSC Quantulus 1220 starts. The decontamination factors are ranging from greater than 10 5 to 10 9 for all important naturally and artificially occurring radionuclides except Sb. The chemical yield stays constant at a value of about 92% up to 0.1 g stable Fe in steel, concrete or other material. The detection limits (confidence level 95%) reach values of 8 mBq per sample or about 60 mBq/g steel and 1.5 mBq/g concrete at a counting time of 1000 minutes. Four to eight analyses are performed by one technician during eight hours. (author) 16 refs.; 2 figs.; 4 tabs

Distribución de los contenidos de Fe y Pb en escombreras, suelos y sedimentos del distrito minero de Linares (Jaén)

OpenAIRE

El Mabrouki, K.; Hidalgo García, J. M.; Hidalgo Estévez, Mari Carmen; Benavente Herrera, José

2002-01-01

Soils and sediments from historical metallic sulphides mining and smelting areas in Linares (jaén) have been sampled for both the determination of the total amount of heavy metals and the analysis by a 5-step sequential extraction procedure. Fe and Pb have been determined on each extraction solution, defined as: exchangeable, bound to carbonates, bound to Fe-Mn oxides, bound to organic matter and sulphides, and residual. High concentrations of the total metals were found in all the 12 studied...

Ferromagnetism in with Fe implanted GaN and TiO{sub 2}; Ferromagnetismus in mit Fe implantierten GaN und TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Talut, Georg

2009-12-15

In the present study it was tried to create a diluted magnetic semiconductor on the basis of GaN and TiO{sub 2} by means of ion beam implantation. In most cases, by characterization of structural and magnetic properties, it was possible to prove that the ferromagnetic state is related to either spinodal decomposition or secondary phase formation. In case of Fe implanted GaN spinodal decomposition, epitaxially oriented {alpha}-Fe or {epsilon}-Fe{sub 3}N nanocrystals were found to be responsible for the ferromagnetic behavior. In addition, the formation of {gamma}-Fe clusters was observed. Similarly, in TiO{sub 2} the ferromagnetism is related to the formation of epitaxially oriented {alpha}-Fe clusters. Dependent on the process parameters during annealing experiments several various secondary phases were formed. A critical examination of the references in literature points out the significance of usage of sensitive and complementary probe techniques (like CEMS, SQUID, XRD, EXAFS), in order to be able to discuss the origin of ferromagnetism in the field of diluted magnetic semiconductors in a proper way. (orig.)

Nanostructure and magnetization reversal process in TbFeCo/Yx(FeCo)1-x spring-magnet type multilayers

International Nuclear Information System (INIS)

Duc, N.H.; Huong Giang, D.T.; Chau, N.

2004-01-01

Studies of the naturally formed nanostructure and magnetization reversal process were performed for the sputtered Tb(Fe 0.55 Co 0.45 ) 1.5 /Y x (Fe 0.7 Co 0.3 ) 1-x multilayers (0≤x≤0.2) with a TbFeCo layer thickness t TbFeCo =12 nm and YFeCo layer thickness t YFeCo =10 nm. The structural investigations showed that nanocrystals are naturally formed and coexist within the amorphous matrix in Y 0.1 (FeCo) 0.9 layers. In this state, low magnetic coercivity and large parallel magnetostrictive susceptibility are observed. The results are discussed in terms of the crystalline discontinuity of the soft YFeCo layers

Magnetocaloric response of La 0.70 Ca 0.1 Sr 0.2 Fe 0.1 Mn 0.9 O 3 ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 38; Issue 1. Magnetocaloric response of La0.70Ca0.1Sr0.2Fe0.1Mn0.9O3 pervoskite for magnetic refrigeration. M S Anwar Faheem Ahmed Bon Heun Koo. Volume 38 Issue 1 February 2015 pp 101-104 ...

Mediterranean Region proficiency test on the determination of radionuclides in air filters. IAEA-CU--2008-02

International Nuclear Information System (INIS)

2009-01-01

The IAEA helps the Member States laboratories to maintain their readiness and improving the quality of the analytical results by producing reference materials, by development of standardized methods for sample collection and analysis, and by conducting interlaboratory comparisons and proficiency tests as a tool for external quality control of analytical results. The Chemistry Unit of the Physics, Chemistry and Instrumentation Laboratory in the International Atomic Energy Agency's Seibersdorf Laboratories in Austria, has the programmatic responsibility to support global radionuclide measurement systems. To fulfil this obligation and ensure a reliable worldwide, rapid and consistent response, the Chemistry Unit organises interlaboratory studies and proficiency tests. The activity concentration of radionuclides in the air is a critical factor in assessing the air quality and the potential impact of possible pollutants. Air is in fact one of the main pathways for human exposure to pollutants. Radioactivity may be present in the atmosphere due to natural processes; intentional (low level) anthropogenic release; or as a consequence of nuclear or radiological incident. Within the frame of the IAEA Technical Cooperation project RER/8/009 'Air Pollution Monitoring in the Mediterranean Region', several Member States expressed their interest in establishing close cooperation among Mediterranean countries in the field of harmonization of air pollution monitoring systems and creation of a common database, since they share geographical position and mutual interest in the environmental conditions of the Mediterranean region. Such cooperation will also promote and enhance the exchange of experience/information. This report summarizes the results of the IAEA-CU-2008-02 Mediterranean Region proficiency test on the determination of radionuclides in air filters

Raman-spectroscopic (Fe/Fe+Mg, CO2) and Structural studies of Mg-Fe cordierites

International Nuclear Information System (INIS)

Haefeker, U.

2013-01-01

In the course of this dissertation synthetic hexagonal and orthorhombic Mg-Fe-cordierites have been investigated with Raman-spectroscopy and XRD methods. Cordierite´s Mg- and Fe-end-members as well as their Mg-Fe solid solutions with the chemical formula (Mg, Fe 2+ ) 2 Al 4 Si 5 O 18 *nH 2 O have been synthesized. Raman-data of synthetic hydrous Mg- and Fe-cordierites have been obtained in the wavenumber-region 100-1250 cm-1 and the experimental data were then compared with the results of quantum-mechanical calculations. 86 theoretical bands could be related to specific vibrational modes of the tetrahedral and octahedral sites of the cordierite structure. Maximum and mean deviation between experimentally-derived bands and calculated modes were ±7 cm -1 for Mg-cordierite and ±19 cm -1 for Fe-cordierite. Spectra comparison revealed a trend of peak downshifting as a consequence of Fe-incorporation. The calculations now allow more accurate interpretation of the Raman spectra with respect to structural changes of cordierite, resulting from Al-Si ordering and Mg-Fe exchange. Atomic motions in cordierite have been compared with those of the structurally similar mineral beryl. Investigations of 16 H 2 O-bearing synthetic well-ordered Mg-Fe-cordierites (XFe =0-1) with micro-Raman spectroscopy revealed a linear correlation between the Fe/Mg ratio and the position of certain Raman peaks. The peaks (wave-number Mg-/Fe-cordierite) at 122/111, 262/257, 430/418, 579/571, 974/967, and 1012/1007 cm -1 were selected for a detailed deconvolution analysis . The shifts of these peaks were then plotted vs. XFe and regression of the data lead to the formulation of a set of linear equations. In addition, the effect of different H 2 O contents and the degree of Al-Si ordering on the Fe/Mg determination were also investigated. Testing the calibration against data from six well-characterized natural cordierite samples yielded excellent agreement. Existing calibration diagrams for CO 2

Moessbauer study of (Fe1-x Cu x )4N (0.05≤x≤0.15) films

International Nuclear Information System (INIS)

El Khiraoui, S.; Sajieddine, M.; Vergnat, M.; Bauer, Ph.; Mabrouki, M.

2007-01-01

In this work, we have prepared nitrogenated Fe 1- x Cu x alloys by reactive evaporation under a flow of nitrogen ions. After annealing, X-ray diffraction shows that we have synthesized the γ'-(Fe 1- x Cu x ) 4 N (0.05≤x≤0.15) compounds. The films were investigated by Moessbauer spectroscopy. The crystallographic structure and the respective positions of the Fe and Cu atoms in the compounds have been determined

Radiologically occult scaphoid and wrist fractures. Preliminary results in comparison of 0.2-T and 1.0-T units

International Nuclear Information System (INIS)

Breitenseher, M.J.; Trattnig, S.; Happel, B.; Bankier, A.; Rand, T.; Imhof, H.; Gaebler, C.; Kukla, C.

1997-01-01

The study was performed to determine the diagnostic value of different MR systems and field strengths in patients with occult scaphoid and wrist fractures. Twelve patients with clinical suspicion of a scaphoid fracture but normal plain radiographs were examined by MRI. A dedicated 0.2-T unit (Esaote) and a 1.0-T unit (NT10, Philips) were used. Coronal T1W-SE, STIR, and T2*W-GE sequences were obtained with both systems. Images were evaluated for a bone marrow abnormality, a trabecular or cortical fracture line, and were compared to the 6-week follow-up radiographs. Seven wrist fractures were found at 0.2 T and 1.0 T, proven in the follow-up radiographs. A bone marrow abnormality was present in all seven fractures on both systems. Trabecular and cortical fracture lines were visualized at 0.2 T in four cases and at 1.0 T in seven cases. Low-field MR imaging at 0.2 T and mid-field MR imaging at 1.0 T seem to be equivalent in the diagnosis of a fracture in radiographically occult scaphoid and wrist fractures. In the visualization of fracture details, important for therapeutic and prognostic considerations, 1.0 T seems to be superior. (orig.) [de

Spectrophotometric determination of dopamine hydrochloride in pharmaceutical, banana, urine and serum samples by potassium ferricyanide-Fe(III).

Science.gov (United States)

Guo, Li; Zhang, Yan; Li, Quanmin

2009-12-01

In the present work, we developed a simple, sensitive and inexpensive method to determine dopamine hydrochloride using potassium ferricyanide-Fe(III) by spectrophotometry. The results show that Fe(III) is deoxidized to Fe(II) by dopamine hydrochloride at pH 4.0, and then Fe(II) reacts with potassium ferricyanide to form a soluble prussian blue (KFe(III)[Fe(II)(CN)6]). The absorbance of this product was monitored over time using a spectrophotometer at an absorption maximum of 735 nm, and the amount of dopamine hydrochloride could be calculated based on the absorbance. A good linear relationship of the concentration of dopamine hydrochloride versus absorbance was observed, and a linear regression equation of A = 0.022 + 0.16921C (microg mL(-1)) was obtained. Moreover, the apparent molar absorption coefficient for the indirect determination of dopamine hydrochloride was 3.2 x 10(4) L mol(-1) cm(-1). This described method has been used to determine dopamine hydrochloride in pharmaceutical, banana, urine and serum samples with satisfactory results.

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of Cr, Fe, Cu, Zn and Se in cereals

Energy Technology Data Exchange (ETDEWEB)

Huang, Shih-Yi [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Jiang, Shiuh-Jen, E-mail: sjjiang@faculty.nsysu.edu.tw [Department of Chemistry, National Sun Yat-sen University, Kaohsiung 80424, Taiwan (China); Department of Medical Laboratory Science and Biotechnology, Kaohsiung Medical University, Kaohsiung 80708, Taiwan (China); Sahayam, A.C. [National Centre for Compositional Characterisation of Materials (CCCM), Hyderabad (India)

2014-11-01

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Cr, Fe, Cu, Zn and Se in several cereal samples. Thioacetamide was used as the modifier to enhance the ion signals. The background ions at the masses of interest were reduced in intensity significantly by using 1.0 mL min{sup −1} methane (CH{sub 4}) as reaction cell gas in the dynamic reaction cell (DRC). Since the sensitivities of Cr, Fe, Cu, Zn and Se in different matrices were quite different, standard addition and isotope dilution methods were used for the determination of Cr, Fe, Cu, Zn and Se in these cereal samples. The method detection limits estimated from standard addition curves were about 1, 10, 4, 12 and 2 ng g{sup −1} for Cr, Fe, Cu, Zn and Se, respectively, in original cereal samples. This procedure has been applied to the determination of Cr, Fe, Cu, Zn and Se whose concentrations are in μg g{sup −1} (except Cr and Se) in standard reference materials (SRM) of National institute of standards and technology (NIST), NIST SRM 1568a Rice Flour and NIST SRM 1567a Wheat Flour and two cereal samples purchased from a local market. The analysis results of reference materials agreed with certified values at 95% confidence level according to Student's T-test. The results for the real world cereal samples were also found to be in good agreement with the pneumatic nebulization DRC ICP-MS results of the sample solutions. - Highlights: • Determination of Cr, Fe, Cu, Zn and Se in cereal samples • Ultrasonic slurry sampling in combination with DRC-ICP-MS • Better sensitivity with thioacetamide modifier in ETV • Decreased sample preparation time with solid sampling • Validation with NIST SRM 1568a Rice Flour and NIST SRM 1567a Wheat Flour.

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of Cr, Fe, Cu, Zn and Se in cereals

International Nuclear Information System (INIS)

Huang, Shih-Yi; Jiang, Shiuh-Jen; Sahayam, A.C.

2014-01-01

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Cr, Fe, Cu, Zn and Se in several cereal samples. Thioacetamide was used as the modifier to enhance the ion signals. The background ions at the masses of interest were reduced in intensity significantly by using 1.0 mL min −1 methane (CH 4 ) as reaction cell gas in the dynamic reaction cell (DRC). Since the sensitivities of Cr, Fe, Cu, Zn and Se in different matrices were quite different, standard addition and isotope dilution methods were used for the determination of Cr, Fe, Cu, Zn and Se in these cereal samples. The method detection limits estimated from standard addition curves were about 1, 10, 4, 12 and 2 ng g −1 for Cr, Fe, Cu, Zn and Se, respectively, in original cereal samples. This procedure has been applied to the determination of Cr, Fe, Cu, Zn and Se whose concentrations are in μg g −1 (except Cr and Se) in standard reference materials (SRM) of National institute of standards and technology (NIST), NIST SRM 1568a Rice Flour and NIST SRM 1567a Wheat Flour and two cereal samples purchased from a local market. The analysis results of reference materials agreed with certified values at 95% confidence level according to Student's T-test. The results for the real world cereal samples were also found to be in good agreement with the pneumatic nebulization DRC ICP-MS results of the sample solutions. - Highlights: • Determination of Cr, Fe, Cu, Zn and Se in cereal samples • Ultrasonic slurry sampling in combination with DRC-ICP-MS • Better sensitivity with thioacetamide modifier in ETV • Decreased sample preparation time with solid sampling • Validation with NIST SRM 1568a Rice Flour and NIST SRM 1567a Wheat Flour

Electrical characteristics of Li(Ni7/10Fe3/10)VO4 ceramics

International Nuclear Information System (INIS)

Ram, Moti

2011-01-01

Graphical abstract: Display Omitted Research highlights: → The compound [Li(Ni 7/10 Fe 3/10 )VO 4 ] was synthesized by a solution-based chemical method. → Structural, microstructural and electrical properties are studied using X-ray diffraction, field emission scanning electron microscopy and complex impedance spectroscopy techniques, respectively. → Electrical conductivity study indicates that electrical conduction in the material is a thermally activated process. - Abstract: The compound [Li(Ni 7/10 Fe 3/10 )VO 4 ] was produced by a solution-based chemical route whose electrical properties were investigated using complex impedance spectroscopy technique. X-ray diffraction study reveals an orthorhombic unit cell structure of the compound. Complex electrical impedance analysis exhibits: (i) grain interior, grain boundary and electrode-material interface contributions to electrical response and (ii) the presence of temperature dependent electrical relaxation phenomena in the material. Electrical conductivity study indicates that electrical conduction in the material is a thermally activated process.

Synthesis and characterization of hexagonal ferrite Sr{sub 1.8}Sm{sub 0.2}Co{sub 2}Ni{sub 1.50}Fe{sub 10.50}O{sub 22}/PST thin films for high frequency application

Energy Technology Data Exchange (ETDEWEB)

Ali, Irshad, E-mail: irshadalibzu@gmail.com [Department of Physics, Bahauddin Zakariya University, Multan P.O. 60800 (Pakistan); Islam, M.U. [Department of Physics, Bahauddin Zakariya University, Multan P.O. 60800 (Pakistan); Ashiq, Muhammad Naeem, E-mail: naeemashiqqau@yahoo.com [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan); Asif Iqbal, M. [Department of Physics, Bahauddin Zakariya University, Multan P.O. 60800 (Pakistan); College of E & ME, National University of Science and Technology, Islamabad (Pakistan); Karamat, Nazia [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan); Azhar Khan, M. [Department of Physics, Islamia University, Bahawalpur 63100 (Pakistan); Sadiq, Imran [Centre of Excellence in Solid State Physics, University of The Punjab, Lahore (Pakistan); Ijaz, Sana [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan); Shakir, Imran [Sustainable Energy Technologies (SET) Center, College of Engineering, King Saud University (Saudi Arabia)

2015-11-01

Y-type hexagonal ferrite (Sr{sub 1.8}Sm{sub 0.2}Co{sub 2}Ni{sub 1.50} Fe{sub 10.50}O{sub 22}) was prepared by a normal microemulsion route. The ferrite/polymer composites thin films are formed at different ferrite ratios in pure polystyrene matrix. The X-ray diffraction analysis shows broad peak at low angles which is due to the PST and the peaks for Y-type ferrite are also observed in composite samples. The peaks become more intense and show less broadening with increasing concentration of ferrite which suggests that crystallinity is improved with the addition of ferrite. DC resistivity of the composites samples is lower than that of the pure PST and decreases by increasing ferrite filler into the polymer. This decrease of resistivity is mainly due to the addition of comparatively less resistive ferrite into the highly insulating polymer matrix of PST. The observed increase in the dielectric constant (permittivity) with increasing concentration ratio of ferrites is mainly due to the electron exchange between Fe{sup 2+}↔Fe{sup 3+}+e{sup −} which consequently results in enhancement of electric polarization as well as dielectric constant. The existence of resonances peaks in the dielectric loss tangent spectra is due to the fact when the external applied frequency becomes equal to the jumping frequency of electrons between Fe{sup 2+} and Fe{sup 3+}. The increasing behavior of the dielectric constant, dielectric loss and AC conductivity with increasing ferrite ratio in PST matrix proposes their versatile use in different technological applications especially for electromagnetic shielding. - Highlights: • Y-type hexaferrites were synthesized by the microemulsion route. • AC activation is lower than DC activation energy. • Ferrite/polymer composites thin films are formed. • The peaks become more intense with increasing concentration of ferrite. • Values of “n” confirm the hopping mechanism in all thin films.

In-situ ionic liquid dispersive liquid-liquid microextraction using a new anion-exchange reagent combined Fe3O4 magnetic nanoparticles for determination of pyrethroid pesticides in water samples.

Science.gov (United States)

Fan, Chen; Liang, You; Dong, Hongqiang; Ding, Guanglong; Zhang, Wenbing; Tang, Gang; Yang, Jiale; Kong, Dandan; Wang, Deng; Cao, Yongsong

2017-07-04

In this work, in-situ ionic liquid dispersive liquid-liquid microextraction combined ultrasmall Fe 3 O 4 magnetic nanoparticles was developed as a kind of pretreatment method to detect pyrethroid pesticides in water samples. New anion-exchange reagents including Na[DDTC] and Na[N(CN) 2 ] were optimized for in-situ extraction pyrethroids, which showed enhanced microextraction performance. Pyrethroids were enriched by hydrophilic ionic liquid [P 4448 ][Br] (aqueous solution, 200 μL, 0.2 mmol mL -1 ) reaction in-situ with anion-exchange reagent Na[N(CN) 2 ] (aqueous solution, 300 μL, 0.2 mmol mL -1 ) forming hydrophobic ionic liquid as extraction agent in water sample (10 mL). Ultrasmall superparamagnetic iron oxide nanoparticles (30 mg) were used to collect the mixture of ionic liquid and pyrethroids followed by elution with acetonitrile. The extraction of ionic liquid strategies was unique and efficiently fulfilled with high enrichment factors (176-213) and good recoveries (80.20-117.31%). The method was successively applied to the determination of pyrethroid pesticides in different kinds of water samples with the limits of detection ranged from 0.16 to 0.21 μg L -1 . The proposed method is actually nanometer-level microextraction (average size 80 nm) with the advantages of simplicity, rapidity, and sensitivity. Copyright © 2017 Elsevier B.V. All rights reserved.

Electronic, magnetic properties and phase diagrams of system with Fe4N compound: An ab initio calculations and Monte Carlo study

Science.gov (United States)

Masrour, R.; Jabar, A.; Hlil, E. K.

2018-05-01

Self-consistent ab initio calculations, based on Density Functional Theory (DFT) approach and using Full potential Linear Augmented Plane Wave (FLAPW) method, are performed to investigate the electronic and magnetic properties of the Fe4N compound. Polarized spin and spin-orbit coupling are included in calculations within the framework of the ferromagnetic state between Fe(I) and Fe(II) in Fe4N compound. We have used the obtained data from abinitio calculations as an input in Monte Carlo simulation to calculate the magnetic properties of this compounds such as the ground state phase diagrams, total and partial magnetization of Fe(I) and Fe(II) as well as the transition temperatures are computed. The variation of magnetization with the crystal field are also studied. The magnetic hysteresis cycle of the same Fe4N compound are determined for different values of temperatures and crystal field values. The two-step hysteresis loop are evidenced, which is typical for Fe4N structure. The ferromagnetic and superparamagnetic phase is observed as well.

Formation of Fe/mg Smectite Under Acidic Conditions from Synthetic Adirondack Basaltic Glass: an Analog to Fe/mg Smectite Formation on Mars

Science.gov (United States)

Sutter, B.; Peretyazhko, T.; Morris, R. V.; Ming, D. W.

2014-01-01

Smectite has been detected as layered material hundreds of meters thick, in intracrater depositional fans, in plains sediments, and deposits at depth on Mars. If early Mars hosted a dense CO2 atmosphere, then extensive carbonate should have formed in the neutral/alkaline conditions expected for smectite formation. However, large carbonate deposits on Mars have not been discovered. Instead of neutral to moderately alkaline conditions, early Mars may have experienced mildly acidic conditions that allowed for Fe/Mg smectite formation but prevented widespread carbonate formation. The objective of this work is to demonstrate that Fe(II)/Mg saponite and nontronite can form in mildly acidic solutions (e.g., pH 4). Synthetic basaltic glass (Smectite was confirmed as the phyllosilicate after treatments with glycerol and KCl and heating to 550 C. Trioctahedral saponite was confirmed by the presence of a 4.58 to 4.63 Angstroms (02l) and 1.54Angstroms (060) peaks. Saponite concentration was highest, as indicated by XRD peak intensity, in the 10 mM Mg treatment followed by the 0 mM and then 10 mM Fe(II) treatments. This order of sapontite concentration suggests that Fe(II) additions may have a role in slowing the kinetics of saponite formation relative to the other treatments. Nontronite synthesis was attempted by exposing Adirondack basaltic glass to pH 4 oxic solutions (without N2 purge) at 200 C for 14 days. X-ray diffraction analysis indicated that mixtures of trioctahedral (saponite) and dioctahedral (nontronite) may have formed in these experiments based on the 02l and 060 peaks. Moessbauer analysis coupled with future experiments are planned to verify if nontronite can be formed under mildly acidic and oxic conditions. Results of this work demonstrate that acidic conditions could have occurred on an early Mars, which allowed for smectite formation but inhibited carbonate formation.

Moessbauer study of C18N/Fe Langmuir-Blodgett layers

Energy Technology Data Exchange (ETDEWEB)

Kuzmann, Erno [Institute of Chemistry, Eoetvoes Lorand University (Hungary); Telegdi, Judit [Institute of Nanochemistry and Catalysis, Chemical Research Center, HAS (Hungary); Nemeth, Zoltan, E-mail: hentes@chem.elte.hu; Vertes, Attila [Institute of Chemistry, Eoetvoes Lorand University (Hungary); Nyikos, Lajos [Institute of Nanochemistry and Catalysis, Chemical Research Center, HAS (Hungary)

2012-03-15

Langmuir-Blodgett (LB) films of octadecanoyl hydroxamic acid (C18N) complexed with Fe{sup 3 + } ions have been prepared at various subphase pH values. The LB films consisting of different number of layers were investigated by {sup 57}Fe conversion electron Moessbauer spectroscopy (CEM) at room temperature. The CEM detector contained a piece of {alpha}-iron, enriched with {sup 57}Fe, using as an internal standard. The Moessbauer pattern of the C18N/Fe LB films is a doublet with parameters {delta} = 0.35 mm/s and {Delta} = 0.74 mm/s. A gradual increase of the relative occurrence of the doublet compared to the sextet of the internal standard was observed with the increasing number of layers, indicating the nearly uniform distribution of Fe among the LB layers.

A screen-printed Ce 0.8Sm 0.2O 1.9 film solid oxide fuel cell with a Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ cathode

Science.gov (United States)

Zhang, Yaohui; Huang, Xiqiang; Lu, Zhe; Liu, Zhiguo; Ge, Xiaodong; Xu, Jiahuan; Xin, Xianshuang; Sha, Xueqing; Su, Wenhui

Screen-printing technology was developed to fabricate Ce 0.8Sm 0.2O 1.9 (SDC) electrolyte films onto porous NiO-SDC green anode substrates. After sintering at 1400 °C for 4 h, a gas-tight SDC film with a thickness of 12 μm was obtained. A novel cathode material of Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ was subsequently applied onto the sintered SDC electrolyte film also by screen-printing and sintered at 970 °C for 3 h to get a single cell. A fuel cell of Ni-SDC/SDC (12 μm)/Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ provides the maximum power densities of 1280, 1080, 670, 370, 180 and 73 mW cm -2 at 650, 600, 555, 505, 455 and 405 °C, respectively, using hydrogen as fuel and stationary air as oxidant. When dry methane was used as fuel, the maximum power densities are 876, 568, 346 and 114 mW cm -2 at 650, 600, 555 and 505 °C, respectively. The present fuel cell shows excellent performance at lowered temperatures.

A strategy for determination of test intervals of k-out-of-n multi-channel systems

International Nuclear Information System (INIS)

Cho, S.; Jiang, J.

2007-01-01

State space models for determination of the optimal test frequencies for k-out-of-n multi channel systems are developed in this paper. The analytic solutions for the optimal surveillance test frequencies are derived using the Markov process technique. The solutions show that an optimal test frequency which maximizes the target probability can be determined by decomposing the system states to 3 states based on the system configuration and success criteria. Examples of quantification of the state probabilities and the optimal test frequencies of a three-channel system and a four-channel system with different success criteria are presented. The strategy for finding the optimal test frequency developed in this paper can generally be applicable to any k-out-of-n multi-channel standby systems that involve complex testing schemes. (author)

Concentration determination of urinary metabolites of N,N-dimethylacetamide by high-performance liquid chromatography-tandem mass spectrometry.

Science.gov (United States)

Yamamoto, Shinobu; Matsumoto, Akiko; Yui, Yuko; Miyazaki, Shota; Kumagai, Shinji; Hori, Hajime; Ichiba, Masayoshi

2018-03-27

N,N-Dimethylacetamide (DMAC) is widely used in industry as a solvent. It can be absorbed through human skin. Therefore, it is necessary to determine exposure to DMAC via biological monitoring. However, the precision of traditional gas chromatography (GC) is low due to the thermal decomposition of metabolites in the high-temperature GC injection port. To overcome this problem, we have developed a new method for the simultaneous separation and quantification of urinary DMAC metabolites using liquid chromatography-tandem mass spectrometry (LC-MS/MS). Urine samples were diluted 10-fold in formic acid, and 1-μl aliquots were injected into the LC-MS/MS equipment. A C18 reverse-phase Octa Decyl Silyl (ODS) column was used as the analytical column, and the mobile phase consisted of a mixture of methanol and aqueous formic acid solution. Urinary concentrations of DMAC and its known metabolites (N-hydroxymethyl-N-methylacetamide (DMAC-OH), N-methylacetamide (NMAC), and S- (acetamidomethyl) mercapturic acid (AMMA) ) were determined in a single run. The dynamic ranges of the calibration curves were 0.05-5 mg/l (r≥0.999) for all four compounds. The limits of detection for DMAC, DMAC-OH, NMAC, and AMMA in urine were 0.04, 0.02, 0.05, and 0.02 mg/l, respectively. Within-run accuracies were 96.5%-109.6% with relative standard deviations of precision being 3.43%-10.31%. The results demonstrated that the proposed method could successfully quantify low concentrations of DMAC and its metabolites with high precision. Hence, this method is useful for evaluating DMAC exposure. In addition, this method can be used to examine metabolite behaviors in human bodies after exposure and to select appropriate biomarkers.

Concentration determination of urinary metabolites of N,N-dimethylacetamide by high-performance liquid chromatography-tandem mass spectrometry

Science.gov (United States)

Yamamoto, Shinobu; Matsumoto, Akiko; Yui, Yuko; Miyazaki, Shota; Kumagai, Shinji; Hori, Hajime; Ichiba, Masayoshi

2017-01-01

Objectives: N,N-Dimethylacetamide (DMAC) is widely used in industry as a solvent. It can be absorbed through human skin. Therefore, it is necessary to determine exposure to DMAC via biological monitoring. However, the precision of traditional gas chromatography (GC) is low due to the thermal decomposition of metabolites in the high-temperature GC injection port. To overcome this problem, we have developed a new method for the simultaneous separation and quantification of urinary DMAC metabolites using liquid chromatography-tandem mass spectrometry (LC-MS/MS). Methods: Urine samples were diluted 10-fold in formic acid, and 1-μl aliquots were injected into the LC-MS/MS equipment. A C18 reverse-phase Octa Decyl Silyl (ODS) column was used as the analytical column, and the mobile phase consisted of a mixture of methanol and aqueous formic acid solution. Results: Urinary concentrations of DMAC and its known metabolites (N-hydroxymethyl-N-methylacetamide (DMAC-OH), N-methylacetamide (NMAC), and S- (acetamidomethyl) mercapturic acid (AMMA) ) were determined in a single run. The dynamic ranges of the calibration curves were 0.05-5 mg/l (r≥0.999) for all four compounds. The limits of detection for DMAC, DMAC-OH, NMAC, and AMMA in urine were 0.04, 0.02, 0.05, and 0.02 mg/l, respectively. Within-run accuracies were 96.5%-109.6% with relative standard deviations of precision being 3.43%-10.31%. Conclusions: The results demonstrated that the proposed method could successfully quantify low concentrations of DMAC and its metabolites with high precision. Hence, this method is useful for evaluating DMAC exposure. In addition, this method can be used to examine metabolite behaviors in human bodies after exposure and to select appropriate biomarkers. PMID:29213009

Peak effect and superconducting properties of SmFeAsO{sub 0.8}F{sub 0.2} wires

Energy Technology Data Exchange (ETDEWEB)

Chen, Y L; Cui, Y J; Yang, Y; Zhang, Y; Wang, L; Zhao, Y [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, and Superconductivity R and D Center (SRDC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C H; Sorrell, C [School of Materials Science and Engineering, University of New South Wales, Sydney, NSW 2052 (Australia)], E-mail: yzhao@swjtu.edu.cn

2008-11-15

Ta-sheathed SmFeAsO{sub 0.8}F{sub 0.2} superconducting wires with T{sub c} = 52.5 K have been fabricated using the powder-in-tube (PIT) method and the superconducting properties of the wires have been investigated. The wires exhibit a very large intragrain critical current density at a temperature below 30 K. A peak effect with maximal J{sub c} = 0.6 MA cm{sup -2} at 10 K under 6 T field was observed. The peak field H{sub pear} is strongly temperature-dependent. A severe weak-link effect depresses the development of global supercurrent owing to a very short coherence length. The wires also show a power law temperature dependence for the irreversibility line with H{sub irr}{approx_equal}(1-T/T{sub c}){sup 1.5}. The H-T phase diagram was found to be similar to that of other superconducting cuprates.

Nanoparticles of La0.8Ca0.2Fe0.8Ni0.2O3-δ perovskite for solid oxide fuel cell application

International Nuclear Information System (INIS)

Ortiz-Vitoriano, N.; Ruiz de Larramendi, I.; Gil de Muro, I.; Ruiz de Larramendi, J.I.; Rojo, T.

2010-01-01

Polycrystalline samples of La 0.8 Ca 0.2 Fe 0.8 Ni 0.2 O 3-δ (LCFN) with perovskite type structure have been prepared by combustion, freeze drying, citrate-gel process and liquid mix method. The analysis of X-ray powder diffraction indicated that the samples were single phase and crystallized in an orthorhombic (space group, Pnma no. 62) structure. Transmission electron microscopy (TEM) analysis on the synthesized powder at 600 o C by liquid mix method showed clusters of 150 nm formed by nanoparticles of 20 nm. Electrochemical performance of LCFN cathodes, which are used for intermediate temperature solid oxide fuel cells, were investigated. The polarization resistance was studied using two different electrolytes: Y-doped zirconia (YSZ) and Sm-doped ceria (SDC). The dc four-probe measurement exhibits a total electrical conductivity, over 100 S cm -1 at T ≥ 600 o C, pointing out that strontium can be substituted for the cheaper calcium cation without destroying the electrochemical properties. Experimental results indicate that nanoparticles have more advantages in terms of smaller particle size and better electrochemical performance.

Properties and performance of BaxSr1-xCo0.8Fe0.2O3-d materials for oxygen transport membranes

NARCIS (Netherlands)

Vente, Jaap F.; McIntosh, S.; McIntosh, Steven; Haije, Wim G.; Bouwmeester, Henricus J.M.

2006-01-01

The present paper discusses the oxygen transport properties, oxygen stoichiometry, phase stability, and chemical and mechanical stability of the perovskites $${\\text{Ba}}_{{0.5}} {\\text{Sr}}_{{0.5}} {\\text{Co}}_{{0.8}} {\\text{Fe}}_{{0.2}} {\\text{O}}_{{3 - \\delta }} $$ (BSCF) and

Rate law of Fe(II) oxidation under low O2 conditions

Science.gov (United States)

Kanzaki, Yoshiki; Murakami, Takashi

2013-12-01

Despite intensive studies on Fe(II) oxidation kinetics, the oxidation rate law has not been established under low O2 conditions. The importance of Fe(II) oxidation under low O2 conditions has been recently recognized; for instance, the Fe(II)/Fe(III) compositions of paleosols, ancient soils formed by weathering, can produce a quantitative pattern of the atmospheric oxygen increase during the Paleoproterozoic. The effects of partial pressure of atmospheric oxygen (PO2) on the Fe(II) oxidation rate were investigated to establish the Fe(II) oxidation rate - PO2 relationships under low O2 conditions. All oxidation experiments were carried out in a glove box by introducing Ar gas at ∼10-5-∼10-4 atm of PO2, pH 7.57-8.09 and 22 °C. Luminol chemiluminescence was adopted to measure low Fe(II) concentrations (down to ∼2 nM). Combining previous data under higher PO2 conditions (10-3-0.2 atm) with the present data, the rate law for Fe(II) oxidation over a wide range of PO2 (10-5-0.2 atm) was found to be written as: d[Fe(II)]/dt=-k[Fe(II)][[]2 where the exponent of [O2], x, and the rate constant, k, change from x = 0.98 (±0.04) and log k = 15.46 (±0.06) at ∼6 × 10-3-0.2 atm of PO2 to x = 0.58 (±0.02) and log k = 13.41 (±0.03) at 10-5-∼6 × 10-3 atm of PO2. The most plausible mechanism that explains the change in x under low O2 conditions is that, instead of O2, oxygen-derived oxidants, H2O2 and to some extent, O2rad -, dominate the oxidation reactions at PO2. The rate law found in the present study requires us to reconsider distributions of Fe redox species at low PO2 in natural environments, especially in paleoweathering profiles, and may provide a deeper understanding of the evolution of atmospheric oxygen in the Precambrian.

Structure refinement of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-d} as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC)

Energy Technology Data Exchange (ETDEWEB)

Zakaria, Nurhamidah, E-mail: nurhamidahzakaria@yahoo.com; Idris, Mohd Sobri, E-mail: sobri@unimap.edu.my [Centre of Excellence for Frontier Materials Research, School of Materials Engineering, Universiti Malaysia Perlis (UniMAP), Taman Muhibbah, Jejawi 02600, Arau, Perlis (Malaysia); Osman, Rozana A. M., E-mail: rozana@unimap.edu.my [School of Microelectronics Engineering, Universiti Malaysia Perlis (UniMAP), Pauh Putra, 02600, Arau, Perlis (Malaysia)

2016-07-19

Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} was successfully prepared using modified solid-state synthesis routes. The lowest temperature to obtained single phase of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} is about 900°C for 15 hours. Longer period of time are required compared to only 5 hours at 950°C as established in literatures. The X-ray Diffraction (XRD) data confirmed that Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} is formed a cubic perovskite with the space group of Pm-3m. The lattice parameters of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} are a = 3.990 (1) Å and unit cell volume is V = 63.5 (1) Å{sup 3}. The Rietveld refinement of XRD data revealed that the crystal structure of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} slightly changes as a function of temperature.

Method of simultaneous continuous determination of transfer rates of iron and chromium into solution during Fe-Cr alloys dissolution

International Nuclear Information System (INIS)

Shirinov, T.I.; Florianovich, G.M.; Skuratnik, Ya.B.

1978-01-01

Radiometry method of simultaneous continuous registration of transfer rates of iron and chromium into solution from Fe-Cr alloys with various composition has been developed. Using gamma-spectrometer components of Fe-Cr alloys can be determined with high sensitivity in separate samples according to Fe 59 and Cr 51 radioactive labels, obtained by neutron activation. The above method is applied to estimate Fe and Cr transfer rates into H 2 SO 4 solution at the temperature of 50 deg from Fe - 28% Cr alloy during its active dissolution. It is established, that beginning with some seconds of alloy and solution contact, its components transfer into the solution in the same composition, as in the alloy. The method enables to determine Fe with the accuracy of up to 5% and Cr with that of up to 10%

Study of Phase Transformations on Nano-Crystalline (La,Sr)(Mn,Fe)O3 Systems by High-Pressure Moessbauer Spectroscopy

International Nuclear Information System (INIS)

Chandra, Usha; Mudgal, Prerana; Kumar, Manoj

2006-01-01

We report pressure-dependent 57Fe Moessbauer studies on a nano-crystalline perovskite La0.8Sr0.2(Mn0.8Fe0.2) O3 system up to 10 GPa using diamond anvil cell. At ambient pressure, iron is present as Fe3+ and Fe4+ in two different environments. Pressure seems to affect the higher symmetry site of Fe4+, while the octahedral site containing Fe3+ remains almost unaffected. Phase transformations are observed at pressures 0.52 GPa and 3.7 GPa respectively. A sudden increase in the isomer shift at 0.52 GPa is related to the reduction of Fe4+ ions while at 3.7 GPa, a structural transition is observed with sudden drop in isomer shift indicating Fe3+ ions in identical environment. Quadrupole splittings increase continuously with pressures up to 10 GPa

Structural and magnetic properties of Fe{sub 76}P{sub 5}(Si{sub 0.3}B{sub 0.5}C{sub 0.2}){sub 19} amorphous alloy

Energy Technology Data Exchange (ETDEWEB)

Lavorato, G.C. [INTECIN (FIUBA-CONICET), Paseo Colon 850, Capital Federal (Argentina); Dipartimento di Chimica IFM and NIS, Universita di Torino, Torino (Italy); Fiore, G. [Dipartimento di Chimica IFM and NIS, Universita di Torino, Torino (Italy); Tiberto, P. [INRIM, Electromagnetism Division, Torino (Italy); Baricco, M. [Dipartimento di Chimica IFM and NIS, Universita di Torino, Torino (Italy); Sirkin, H. [INTECIN (FIUBA-CONICET), Paseo Colon 850, Capital Federal (Argentina); Moya, J.A., E-mail: jmoya.fi.uba@gmail.com [GIM - IESIING, Universidad Catolica de Salta, INTECIN (UBA-CONICET) (Argentina)

2012-09-25

Highlights: Black-Right-Pointing-Pointer Fe{sub 76}P{sub 5}(Si{sub 0.3}B{sub 0.5}C{sub 0.2}){sub 19} amorphous alloy in ribbons and 1 mm and 2 mm rod samples. Black-Right-Pointing-Pointer Good glass forming ability with {Delta}T = 50 K and {gamma} = 0.37 and off-eutectic composition. Black-Right-Pointing-Pointer Good soft magnetic properties with magnetization saturation of 1.44 T. Black-Right-Pointing-Pointer Geometrical factors are the primary causes of magnetic losses in frequencies above 10 Hz. - Abstract: Recently, bulk amorphous alloys were produced in the Fe-B-Si-P-C system with high glass forming ability, excellent magnetic properties and the advantage of containing no expensive glass-forming elements, such as Ga, Y, Cr or Nb, having, therefore, a good perspective of commercial applications. In the present work, the Fe{sub 76}P{sub 5}(Si{sub 0.3}B{sub 0.5}C{sub 0.2}){sub 19} amorphous alloy prepared by two quenching techniques has been studied. Amorphous ribbons of about 40 {mu}m thick were obtained by planar-flow casting together with cylinders having 1 and 2 mm diameter produced by copper mold injection casting. All the samples appear fully amorphous after X-ray diffraction analysis. A comprehensive set of thermal data (glass, crystallization, melting and liquidus temperatures) were obtained as well as a description of the melting and solidification processes. Mechanical microhardness tests showed that the samples have a hardness of 9.7 {+-} 0.3 GPa. Good soft-magnetic properties were obtained, including a high magnetization of 1.44 T and a low coercivity (4.5 A/m for ribbons and 7.5 A/m in the case of 1 mm rod samples, both in as-cast state). Thermomagnetic studies showed a Curie temperature around 665 K and the precipitation of new magnetic phases upon temperatures of 1000 K. Furthermore, the frequency dependence of magnetic losses at a fixed peak induction was studied. The results suggest the occurrence of a fine magnetic domain structure in bulk

Nitrogen versus helium: effects of the choice of the atomizing gas on the structures of Fe50Ni30Si10B10 and Fe32Ni36Ta7Si8B17 powders

International Nuclear Information System (INIS)

Zambon, A.

2004-01-01

Gas atomization can produce, besides a possible significant degree of undercooling, high cooling rates, whose extent depends on the size of the droplets, on their velocity with respect to the surrounding medium, on the thermo-physical properties of both the alloy and the gas, and of course on the operating conditions such as melt overheating and gas-to-metal flow ratio. In this respect it is well-known that the atomizing gas can play a significant role in determining both the powder size distribution and the kind and mix of phases which result from the solidification and cooling processes. The microstructures and solidification morphologies of powders obtained from nitrogen and helium sonic gas atomization of two iron-nickel base glass forming alloys, Fe 50 Ni 30 Si 10 B 10 and Fe 32 Ni 36 Ta 7 Si 8 B 17 , were investigated by means of light microscopy, X-ray diffraction (XRD) and differential thermal analysis (DTA). The Fe 32 Ni 36 Ta 7 Si 8 B 17 alloy exhibits a higher proneness to the development of amorphous phase than the Fe 50 Ni 30 Si 10 B 10 alloy, while the effect of the higher speed attainable by the stream of helium with respect to that of nitrogen, affords not only to obtain a larger amount of particles in the finer size ranges, but also to affect the relative amounts of phases within the different size fractions

Models of f(R) cosmic acceleration that evade solar system tests

International Nuclear Information System (INIS)

Hu, Wayne; Sawicki, Ignacy

2007-01-01

We study a class of metric-variation f(R) models that accelerates the expansion without a cosmological constant and satisfies both cosmological and solar-system tests in the small-field limit of the parameter space. Solar-system tests alone place only weak bounds on these models, since the additional scalar degree of freedom is locked to the high-curvature general-relativistic prediction across more than 25 orders of magnitude in density, out through the solar corona. This agreement requires that the galactic halo be of sufficient extent to maintain the galaxy at high curvature in the presence of the low-curvature cosmological background. If the galactic halo and local environment in f(R) models do not have substantially deeper potentials than expected in ΛCDM, then cosmological field amplitudes |f R | > or approx.10 -6 will cause the galactic interior to evolve to low curvature during the acceleration epoch. Viability of large-deviation models therefore rests on the structure and evolution of the galactic halo, requiring cosmological simulations of f(R) models, and not directly on solar-system tests. Even small deviations that conservatively satisfy both galactic and solar-system constraints can still be tested by future, percent-level measurements of the linear power spectrum, while they remain undetectable to cosmological-distance measures. Although we illustrate these effects in a specific class of models, the requirements on f(R) are phrased in a nearly model-independent manner

Sol-gel based optical sensor for determination of Fe (II): a novel probe for iron speciation.

Science.gov (United States)

Samadi-Maybodi, Abdolraouf; Rezaei, Vida; Rastegarzadeh, Saadat

2015-02-05

A highly selective optical sensor for Fe (II) ions was developed based on entrapment of a sensitive reagent, 2,4,6-tri(2-pyridyl)-s-triazine (TPTZ), in a silica sol-gel thin film coated on a glass substrate. The thin films fabricated based on tetraethoxysilane (TEOS) as precursor, sol-gel pH∼3, water:alkoxyde ratio of 4:1 and TPTZ concentration of 0.112 mol L(-1). The influence of sol-gel parameters on sensing behavior of the fabricated sensor was also investigated. The fabricated sensor can be used for determination of Fe (II) ion with an outstanding high selectivity over a dynamic range of 5-115 ng mL(-1) and a detection limit of 1.68 ng mL(-1). It also showed reproducible results with relative standard deviation of 3.5% and 1.27% for 10 and 90 ng mL(-1) of Fe (II), respectively, along with a fast response time of ∼120 s. Total iron also was determined after reduction of Fe (III) to Fe (II) using ascorbic acid as reducing agent. Then, the concentration of Fe (III) was calculated by subtracting the concentration of Fe (II) from the total iron concentration. Interference studies showed a good selectivity for Fe (II) with trapping TPTZ into sol-gel matrix and appropriately adjusting the structure of doped sol-gel. The sensor was compared with other sensors and was applied to determine iron in different water samples with good results. Copyright © 2014 Elsevier B.V. All rights reserved.

Optical determination of glucose and hydrogen peroxide using a nanocomposite prepared from glucose oxidase and magnetite nanoparticles immobilized on graphene oxide

International Nuclear Information System (INIS)

Chang, Qing; Tang, Heqing

2014-01-01

Fe 3 O 4 nanoparticles were deposited on sheets of graphene oxide (GO) by a precipitation method, and glucose oxidase (GOx) was then immobilized on this material to produce a GOx/Fe 3 O 4 /GO magnetic nanocomposite containing crosslinked enzyme clusters. The 3-component composite functions as a binary enzyme that was employed in a photometric method for the determination of glucose and hydrogen peroxide where the GOx/Fe 3 O 4 /GO nanoparticles cause the generation of H 2 O 2 which, in turn, oxidize the substrate N,N-diethyl-p-phenylenediamine to form a purple product with an absorption maximum at 550 nm. The absorbance at 550 nm can be correlated to the concentration of glucose and/or hydrogen peroxide. Under optimized conditions, the calibration plot is linear in the 0.5 to 600 μM glucose concentration range, and the detection limit is 0.2 μM. The respective plot for H 2 O 2 ranges from 0.1 to 10 μM, and the detection limit is 0.04 μM. The method was successfully applied to the determination of glucose in human serum samples. The GOx/Fe 3 O 4 /GO nanoparticles are reusable. (author)

Voltammetry of Organic Pollutants on FeOOH Nanorods

International Nuclear Information System (INIS)

Zhang, Yuanyuan; Wan, Qijin; Yang, Nianjun

2017-01-01

FeOOH nanorods synthesized using a solvothermal approach have been employed to investigate the electrochemistry of organic pollutions, including ponceau 4R (PR), sunset yellow (SY), and tetrabromobisphenol A (TBBPA). The as-prepared FeOOH nanorods have been characterized using scanning electron microscopes (SEM), transmission electron microscope (TEM), X-ray photoelectron spectrometry, Brunauer-Emmett-Teller measurements, and electrochemical techniques. The modified electrode based on FeOOH nanorods exhibits a porous and net-like structure, resulting in a high surface area and many reactive/adsorption sites for soluble compounds. On this modified electrode, fast electron transfer processes of redox probes have been achieved. Electrochemistry of PR, SY, and TBBPA has been studied in detail using voltammetry, impedance, and chronocoulometry. The sensitive monitoring of both individual and total concentrations of three organic pollutions has been realized. The detection limits are 0.2, 1.0, and 0.55 nM for PR, SY, and TBBPA, respectively. Such an electrode is then promising for the electrochemical investigation and analysis of organic pollutions in different environments.

Measurement of beta decay periods for Fe-Ni neutrons rich isotopes

International Nuclear Information System (INIS)

Czajkowski, S.

1992-01-01

Thermal fission of 239 Pu was used to produce 68,69 Co and 68 Fe isotopes, the lightest ones ever observed in thermal fission, at the ILL high-flux reactor, in Grenoble. Separated with the Lohengrin recoil spectrometer, then identified by means of a Δ E-E ionization chamber, fragments were implanted in a set of Si-detectors, where β-particles were detected too. The fission yields were determined, and the beta-decay half-lives were extracted from delayed coincidence analysis between ion implantation and the subsequent beta detection: They were found to be 0.27±0.05s, 0.18±0.10s, and 0.10±0.06s respectively for 69 Co, 68 Co, and 68 Fe. This method was adapted to a new experimental configuration: 65 Fe isotopes were produced from 86 Kr projectile fragmentation at 500 MeV/u on a Be target. Selected ions were separated with the fragment separator FRS at GSI (Darmstadt), tuned in the monoenergetic mode. Fragments were identified by ΔE-ToF, slowed down, and then implanted in two rows of PIN-diodes that provided an additional range selection. The half-life were determined from the analysis of the decay chain Fe-Co-Ni: it was found 0.4±0.2s. Production rates obtained with the two methods are compared at the end of this work

DFT calculations on N2O decomposition by binuclear Fe complexes in Fe/ZSM-5

NARCIS (Netherlands)

Yakovlev, A.L.; Zhidomirov, G.M.; Santen, van R.A.

2001-01-01

N2O decomposition catalyzed by oxidized Fe clusters localized in the micropores of Fe/ZSM-5 has been studied using the DFT approach and a binuclear cluster model of the active site. Three different reaction routes were found, depending on temperature and water pressure. The results show that below

Spin Polarization Inversion at Benzene-Absorbed Fe4N Surface

KAUST Repository

Zhang, Qian; Mi, Wenbo; Wang, Xiaocha; Wang, Xuhui

2015-01-01

We report a first-principle study on electronic structure and simulation of the spin-polarized scanning tunneling microscopy graphic of a benzene/Fe4N interface. Fe4N is a compound ferromagnet suitable for many spintronic applications. We found that, depending on the particular termination schemes and interface configurations, the spin polarization on the benzene surface shows a rich variety of properties ranging from cosine-type oscillation to polarization inversion. Spin-polarization inversion above benzene is resulting from the hybridizations between C pz and the out-of-plane d orbitals of Fe atom.

Spin Polarization Inversion at Benzene-Absorbed Fe4N Surface

KAUST Repository

Zhang, Qian

2015-05-27

We report a first-principle study on electronic structure and simulation of the spin-polarized scanning tunneling microscopy graphic of a benzene/Fe4N interface. Fe4N is a compound ferromagnet suitable for many spintronic applications. We found that, depending on the particular termination schemes and interface configurations, the spin polarization on the benzene surface shows a rich variety of properties ranging from cosine-type oscillation to polarization inversion. Spin-polarization inversion above benzene is resulting from the hybridizations between C pz and the out-of-plane d orbitals of Fe atom.

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

Energy Technology Data Exchange (ETDEWEB)

Pacold, J. I.; Lukens, W. W.; Booth, C. H.; Shuh, D. K. [Chemical Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Knight, K. B.; Eppich, G. R. [Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Holliday, K. S. [Materials Science Division, Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

2016-05-21

Nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. We find significant variations among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. The resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.

Chemical speciation of U, Fe, and Pu in melt glass from nuclear weapons testing

Science.gov (United States)

Pacold, J. I.; Lukens, W. W.; Booth, C. H.; Shuh, D. K.; Knight, K. B.; Eppich, G. R.; Holliday, K. S.

2016-05-01

Nuclear weapons testing generates large volumes of glassy materials that influence the transport of dispersed actinides in the environment and may carry information on the composition of the detonated device. We determine the oxidation state of U and Fe (which is known to buffer the oxidation state of actinide elements and to affect the redox state of groundwater) in samples of melt glass collected from three U.S. nuclear weapons tests. For selected samples, we also determine the coordination geometry of U and Fe, and we report the oxidation state of Pu from one melt glass sample. We find significant variations among the melt glass samples and, in particular, find a clear deviation in one sample from the expected buffering effect of Fe(II)/Fe(III) on the oxidation state of uranium. In the first direct measurement of Pu oxidation state in a nuclear test melt glass, we obtain a result consistent with existing literature that proposes Pu is primarily present as Pu(IV) in post-detonation material. In addition, our measurements imply that highly mobile U(VI) may be produced in significant quantities when melt glass is quenched rapidly following a nuclear detonation, though these products may remain immobile in the vitrified matrices. The observed differences in chemical state among the three samples show that redox conditions can vary dramatically across different nuclear test conditions. The local soil composition, associated device materials, and the rate of quenching are all likely to affect the final redox state of the glass. The resulting variations in glass chemistry are significant for understanding and interpreting debris chemistry and the later environmental mobility of dispersed material.

Anode-supported single-chamber solid oxide fuel cell based on cobalt-free composite cathode of Nd0.5Sr0.5Fe0.8Cu0.2O3-δ-Sm0.2Ce0.8O1.9 at intermediate temperatures

Science.gov (United States)

Yin, Jie-Wei; Zhang, Chunming; Yin, Yi-Mei; Shi, Huangang; Lin, Ye; Lu, Jun; Ma, Zi-Feng

2015-07-01

As a candidate of cathode material of single-chamber solid oxide fuel cell (SC-SOFC), cobalt-free mixed ionic electronic conductor (MIEC) Nd0.5Sr0.5Fe0.8Cu0.2O3-δ (NSFCu) is synthesized by sol-gel method with ethylene diamine tetraacetic acid and citric acid as co-complexing agents. The XRD shows NSFCu is stable after CO2 treatment and chemical compatible with SDC at high temperatures. CO2-TPD (CO2-temperature programmed desorption) demonstrates both CO2 adsorption and desorption phenomenon on NSFCu surface. However, the polarization resistances (Rp) of NSFCu and SDC (10:4 in weight) composite electrodes showed no decay in 5% CO2. Single cell using N2-O2-CH4 mixed gas (CH4 to O2 ratio = 1.5) as fuel shows maximum power density of 635 mW cm-2 at 700 °C. These results suggest that NSFCu-SDC is a promising composite cathode material for application in single-chamber solid oxide fuel cell.

Synthesis of BaBi0.2Co0.35Fe0.45O3−δ by a novel aqueous soft chemical method and its characterizations

International Nuclear Information System (INIS)

Islam, Quazi Arif; Raja, Mir Wasim; Basu, Rajendra Nath

2014-01-01

Highlights: • Novel combustion process developed first time to synthesize BaBi 0.2 Co 0.35 Fe 0.45 O 3−δ . • The synthesis method is techno-economically viable. • During synthesis, thermal behavior of different complexes studied in detail. • Almost full densification (∼98%) is obtained in sintered samples. • Highest electrical conductivity of 10.38 S cm −1 is obtained at 800 °C. -- Abstract: BaBi 0.2 Co 0.35 Fe 0.45 O 3−δ (BBCF) single phase perovskite has been successfully synthesized by a novel alanine assisted soft chemical combustion method. Thermal behavior of metal alanine complexes during combustion to form BBCF perovskite structure has been studied in detail. X-ray diffraction patterns reveal that the formation of single phase BBCF perovskite proceeds by formation of several intermediate phases. A single phase BBCF powder is obtained at a temperature of 950 °C. Homogeneous distribution of multiple dopants in BBCF matrix is confirmed by elemental mapping using FESEM. The electrical conductivity reveals that with the increase in sintering temperature, conductivity of BBCF increases, reaches to a maximum value of 10.38 S cm −1 at 800 °C when measured in air for samples sintered at 950 °C and upon further increase in sintering temperature, the conductivity decreases gradually. Up to 800 °C, BBCF shows a semiconducting behavior and subsequently follows metallic conduction above 800 °C while performing electrical conductivity measurement in air

Calorimetric investigation into interaction in Zr0.8Ti0.2CrFe-H2 system

International Nuclear Information System (INIS)

Sirotina, R.A.; Verbetskij, V.N.

1993-01-01

For studying Zr 0.8 Ti 0.2 CrFe-H 2 system is applied the calorimetric method with usage of the Tian-Calve type calorimeter. It is shown that up to 488 K in the system there are three characteristic regions: α (hydrogen solution in an intermetallic compounds (IMC)), β (hydrogen solution in a hydride) and α + β (region of coexistence of two phases). Temperature 448 K is near to critical one, when exceeding of which exists only hydrogen solution in a metal matrix. Pressure dependence of hydrogen content in IMC is described satisfactorily by a linear equation

Determination of N-acetylglucosamine in cosmetic formulations and skin test samples by hydrophilic interaction liquid chromatography and UV detection.

Science.gov (United States)

Pedrali, Alice; Bleve, Mariella; Capra, Priscilla; Jonsson, Tobias; Massolini, Gabriella; Perugini, Paola; Marrubini, Giorgio

2015-03-25

N-Acetylglucosamine is an ingredient in pharmaceuticals, nutritional supplements and in cosmetics. N-Acetylglucosamine in cosmetics is expected to improve skin hydration, reparation, and to contribute as anti-wrinkle agent. This study reports on the validation and application of an HPLC method based on HILIC and UV detection for determining N-acetylglucosamine in cosmetics and in samples obtained after testing the skin exposed to cosmetics formulations. The chromatographic column used is a ZIC(®)-pHILIC (150 mm × 4.6 mm, 5 μm particle size) on which a mobile phase containing acetonitrile-aqueous KH2PO4 (70:30, v/v) 15 mM was applied in isocratic elution mode injecting 20 μl of sample at 0.5 ml/min constant flow-rate and 10±1°C column temperature. Under these conditions the total run time was 10 min and N-acetylglucosamine eluted baseline separated from all other compounds in the samples. Calibration in the range from 40 to 80 μg/ml allowed to assess the method linearity (R(2)>0.999) in a concentration range corresponding to about 50% to 120% of the expected levels of N-acetylglucosamine in the formulations. Precision expressed by RSD% was always better than 2% in intra-day and inter-day assays of authentic samples. Accuracy was in all cases within 95-105% of the expected concentration value in formulations containing N-acetylglucosamine. The sensitivity of the method was at the level of 10 μg/ml as limit of detection, and at 40 μg/ml as limit of quantitation. The application of the method to formulations containing solid lipid nanoparticles documents its usefulness in cosmetic quality control. The results witness that the method is also suitable for the determination of N-acetylglucosamine in samples obtained from skin test strips. Copyright © 2014 Elsevier B.V. All rights reserved.

Spatial anisotropy of neutrons emitted from the 56Fe(γ ,n )55Fe reaction with a linearly polarized γ -ray beam

Science.gov (United States)

Hayakawa, T.; Shizuma, T.; Miyamoto, S.; Amano, S.; Takemoto, A.; Yamaguchi, M.; Horikawa, K.; Akimune, H.; Chiba, S.; Ogata, K.; Fujiwara, M.

2016-04-01

We have measured the azimuthal anisotropy of neutrons emitted from the 56Fe(γ ,n )55Fe reaction with a linearly polarized γ -ray beam generated by laser Compton scattering at NewSUBARU. Neutron yields at the polar angle of 90∘ have been measured as a function of the azimuthal angle ϕ between the detector and the linear polarization plane of the γ -ray beam. The azimuthal anisotropy of neutrons measured at ϕ =0∘ , 10∘, 25∘, 45∘, 60∘, 70∘, and 90∘ has been well reproduced using a theoretically predicted function of a +b cos(2 ϕ ) .

Point defects as a test ground for the local density approximation +U theory: Mn, Fe, and V{sub Ga} in GaN

Energy Technology Data Exchange (ETDEWEB)

Volnianska, O.; Zakrzewski, T. [Institute of Physics PAS, 02-668 Warsaw (Poland); Boguslawski, P. [Institute of Physics PAS, 02-668 Warsaw (Poland); Institute of Physics, Kazimierz Wielki University, 85-072 Bydgoszcz (Poland)

2014-09-21

Electronic structure of the Mn and Fe ions and of the gallium vacancy V{sub Ga} in GaN was analysed within the GGA + U approach. First, the +U term was treated as a free parameter, and applied to p(N), d(Mn), and d(Fe). The band gap of GaN is reproduced for U(N) ≈ 4 eV. The electronic structure of defect states was found to be more sensitive to the value of U than that of the bulk states. Both the magnitude and the sign of the U-induced energy shifts of levels depend on occupancies, and thus on the defect charge state. The energy shifts also depend on the hybridization between defect and host states, and thus are different for different level symmetries. In the case of V{sub Ga}, these effects lead to stabilization of spin polarization and the “negative-U{sub eff}” behavior. The values of Us were also calculated using the linear response approach, which gives U(Fe) ≈ U(Mn) ≈ 4 eV. This reproduces well the results of previous hybrid functionals calculations. However, the best agreement with the experimental data is obtained for vanishing or even negative U(Fe) and U(Mn)

Zn-10.2% Fe coating over carbon steel atmospheric corrosion resistance. Comparison with zinc coating

International Nuclear Information System (INIS)

Arnau, G.; Gimenez, E.; Rubio, M.V.; Saura, J.J.; Suay, J.J.

1998-01-01

Zn-10.2% Fe galvanized coating versus hot galvanized coating over carbon steel corrosion performance has been studied. Different periods of atmospheric exposures in various Valencia Community sites, and salt spray accelerated test have been done. Carbon steel test samples have been used simultaneously in order to classify exposure atmosphere corrosivity, and environmental exposure atmosphere characteristics have been analyzed. Corrosion Velocity versus environmental parameters has been obtained. (Author) 17 refs

Interfacial Exchange Coupling Induced Anomalous Anisotropic Magnetoresistance in Epitaxial γ′-Fe 4 N/CoN Bilayers

KAUST Repository

Li, Zirun; Mi, Wenbo; Wang, Xiaocha; Zhang, Xixiang

2015-01-01

Anisotropic magnetoresistance (AMR) of the facing-target reactively sputtered epitaxial γ′-Fe4N/CoN bilayers is investigated. The phase shift and rectangular-like AMR appears at low temperatures, which can be ascribed to the interfacial exchange coupling. The phase shift comes from the exchange bias (EB) that makes the magnetization lag behind a small field. When the γ′-Fe4N thickness increases, the rectangular-like AMR appears. The rectangular-like AMR should be from the combined contributions including the EB-induced unidirectional anisotropy, intrinsic AMR of γ′-Fe4N layer and interfacial spin scattering.

Interfacial Exchange Coupling Induced Anomalous Anisotropic Magnetoresistance in Epitaxial γ′-Fe 4 N/CoN Bilayers

KAUST Repository

Li, Zirun

2015-02-02

Anisotropic magnetoresistance (AMR) of the facing-target reactively sputtered epitaxial γ′-Fe4N/CoN bilayers is investigated. The phase shift and rectangular-like AMR appears at low temperatures, which can be ascribed to the interfacial exchange coupling. The phase shift comes from the exchange bias (EB) that makes the magnetization lag behind a small field. When the γ′-Fe4N thickness increases, the rectangular-like AMR appears. The rectangular-like AMR should be from the combined contributions including the EB-induced unidirectional anisotropy, intrinsic AMR of γ′-Fe4N layer and interfacial spin scattering.

Lista y distribución de los ofidios (Reptilia: Serpentes de Santa Fe, Argentina

Directory of Open Access Journals (Sweden)

Arzamendia, Vanesa

2002-05-01

Full Text Available Se estudió la composición y distribución de las serpientes en la provincia de Santa Fe, Argentina, sobre la base de 1.292 registros obtenidos en muestreos de campo, revisión de las colecciones herpetológicas de Argentina y registros bibliográficos. Se registraron 51 especies y subespecies (43 Colubridae, 3 Viperidae, 2 Boidae, 1 Elapidae, 1 Leptotyphlopidae y 1 Typhlopidae, representando un 39% de los taxones registrados para Argentina. Se realizaron mapas con localidades precisas para determinar la distribución de las serpientes. Una especie y 4 subespecies son registros novedosos para la provincia. Los patrones de distribución son brevemente discutidos en relación con las formaciones fitogeográficas. We studied the composition and distribution of the Santa Fe snakes based on 1,292 examined specimens obtained in field survey, revision of the Argentine herpetological collections and reliable literature records. Maps were built for determinate the distribution of snakes. Fifty one species and subspecies were recorded (43 Colubridae, 3 Viperidae, 2 Boidae, 1 Elapidae, 1 Leptotyphlopidae and 1 Typhlopidae, a 39% of the survey taxa in Argentina. One species and three subspecies were new records in Santa Fe province. The distributional patterns are briefly discussed in relation with phytogeographical subdivisions.

A study of (Ba0.5Sr0.5)1-xSm xCo0.8Fe0.2O3-δ as a cathode material for IT-SOFCs

International Nuclear Information System (INIS)

Li Shuyan; Lue Zhe; Wei Bo; Huang Xiqiang; Miao Jipeng; Cao Gang; Zhu Ruibin; Su Wenhui

2006-01-01

(Ba 0.5 Sr 0.5 ) 1-x Sm x Co 0.8 Fe 0.2 O 3-δ (BSSCF; x = 0.05-0.15) compounds were synthesized with EDTA-Pechini method and characterized by powder X-ray diffraction (XRD), electrical conductivity and thermal expansion coefficient (TEC) measurements, as well as the electrochemical impedance spectra measurement. According to the XRD results, the main phase of the material belongs to the cubic perovskite-type, and the lattice contracting with the increasing contents of Sm 3+ . The TEC of the compounds is 19.1-20.3 x 10 -6 K -1 from 30 to 800 deg. C, which close to the values of Co-based materials, such as Ba 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3-δ (BSCF). And the conductivity of BSSCF is higher than that of BSCF; e.g., about 212% higher at 500 deg. C for the x = 0.15 compound. Electrochemical impedance spectra at intermediate temperature revealed the better electrochemical performance of BSSCF than BSCF; e.g., the total resistance values of BSSCF electrode is 2.98 Ω cm 2 at 500 deg. C, nearly 50% lower than that of BSCF

Investigations on FCAM-III (Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36): A new homologue of the aenigmatite structure-type in the system CaO-MgO-Fe2O3-Al2O3

Science.gov (United States)

Zöll, Klaus; Kahlenberg, Volker; Krüger, Hannes; Tropper, Peter

2018-02-01

In the course of a systematic study of a part of the quaternary system Fe2O3-CaO-Al2O3-MgO (FCAM) the previously unknown compound Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 (FCAM-III) has been synthesized. By analogy with the so-called SFCA series [1-5], our investigation in the system of FCAM shows the existence of a stoichiometric homologous series M14+6nO20+8n, where M = Fe, Ca, Al, Mg and n = 1 or 2. In air, we can prove the formation of coexisting FCAM-III and FCAM-I solid solutions at 1400 °C. By increasing the temperature up to 1425 °C FCAM-I disappears completely and FCAM-III co-exists with magnesiumferrite and a variety of calcium iron oxides. At 1450 °C FCAM-III breaks down to a mixture of FCAM-I again as well as magnesioferrite and melt. Small single-crystals of FCAM-III up to 35 μm in size could be retrieved from the 1425 °C experiment and were subsequently characterized using electron microprobe analysis and synchroton X-ray single-crystal diffraction. Finally the Fe2+/Fetot ratio was calculated from the total iron content based on the crystal-chemical formula obtained from EMPA measurements and charge balance considerations. FCAM-III or Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 has a triclinic crystal structure (space group P 1 ̅). The basic crystallographic data are: a = 10.223(22) Å, b = 10.316(21) Å, c = 14.203(15) Å, α = 93.473(50)°, β = 107.418(67)°, γ = 109.646(60)°, V = 1323.85(2) ų, Z = 1. Using Schreinemaker's technique to analyze the phase relations in the system Fe2O3-CaO-Al2O3-MgO it was possible to obtain the semi-quantitative stability relations between the participating phases and construct a topologically correct phase sequence as a function of T and fO2. The analysis shows that Ca2Al0.5Fe1.5O5 (C2A0.25F0.75) and CaAl1.5Fe2.5O7 (CA0.75F1.25) with higher calculated Fe2+ contents are preferably formed at lower oxygen fugacity and react to CaAl0.5Fe1.5O4 (CA0.25F0.75) by increasing fO2. Spinel-type magnesium

AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Li Jinlong; Mao Shoudong; Sun Kefei [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Li Xiaomin [Shanghai Institute of Ceramics Chinese Academy of Sciences, Shanghai 200050 (China); Song Zhenlun [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)], E-mail: songzhenlun@nimte.ac.cn

2009-11-15

AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.