Conservatism of ASME KIR-reference curve with respect to crack arrest

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.; Nagel, G.

2001-01-01

The conservatism of the RT NDT temperature indexing parameter and the ASME K IR -reference curve with respect to crack arrest toughness, has been evaluated. Based on an analysis of the original ASME K Ia data, it was established that inherently, the ASME K IR -reference curve corresponds to an overall 5% lower bound curve with respect to crack arrest. It was shown that the scatter of crack arrest toughness is essentially material independent and has a standard deviation (S.D.) of 18% and the temperature dependence of K Ia has the same form as predicted by the master curve for crack initiation toughness. The 'built in' offset between the mean 100 MPa√m crack arrest temperature, TK Ia , and RT NDT is 38 deg. C (TK Ia =RT NDT +38 deg. C) and the experimental relation between TK Ia and NDT is, TK Ia =NDT+28 deg. C. The K IR -reference curve using NDT as reference temperature will be conservative with respect to the general 5% lower bound K Ia(5%) -curve, with a 75% confidence. The use of RT NDT , instead of NDT, will generally increase the degree of conservatism, both for non-irradiated as well as irradiated materials, close to a 95% confidence level. This trend is pronounced for materials with Charpy-V upper shelf energies below 100 J. It is shown that the K IR -curve effectively constitutes a deterministic lower bound curve for crack arrest The findings are valid both for nuclear pressure vessel plates, forgings and welds

Methods of forging steel

OpenAIRE

Pečoler, Primož

2014-01-01

The following work presents processes of steel forming, challenges when forging steel, forming machines suitable for forging and which choice of machine is most suitable for forging. We can separate steel forming to free forging and drop forging. Free forging can be divided to hand forging and machine forging. The correct choice of furnaces is also very important. We must reach correct temperature in the furnace for raw steel to melt with less scalings. In diploma I mentioned some machine...

Structural analysis of the JT-60SA cryostat vessel body

Energy Technology Data Exchange (ETDEWEB)

Botija, José, E-mail: jose.botija@ciemat.es [Association EURATOM – CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Alonso, Javier; Fernández, Pilar; Medrano, Mercedes; Ramos, Francisco; Rincon, Esther; Soleto, Alfonso [Association EURATOM – CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Davis, Sam; Di Pietro, Enrico; Tomarchio, Valerio [Fusion for Energy, JT-60SA European Home Team, 85748 Garching bei Munchen (Germany); Masaki, Kei; Sakasai, Akira; Shibama, Yusuke [JAEA – Japan Atomic Energy Agency, Naka Fusion Institute, Ibaraki 311-0193 (Japan)

2013-10-15

Highlights: ► Structural analysis to validate the JT-60SA cryostat vessel body design. ► Design code ASME 2007 “Boiler and Pressure Vessel Code. Section VIII”. ► First buckling mode: load multiplier of 10.644, higher than the minimum factor 4.7. ► Elastic and elastic–plastic stress analysis meets ASME against plastic collapse. ► Bolted fasteners have been analyzed showing small gaps closed by strong welding. -- Abstract: The JT-60SA cryostat is a stainless steel vacuum vessel (14 m diameter, 16 m height) which encloses the Tokamak providing the vacuum environment (10{sup −3} Pa) necessary to limit the transmission of thermal loads to the components at cryogenic temperature. It must withstand both external atmospheric pressure during normal operation and internal overpressure in case of an accident. The paper summarizes the structural analyses performed in order to validate the JT-60SA cryostat vessel body design. It comprises several analyses: a buckling analysis to demonstrate stability under the external pressure; an elastic and an elastic–plastic stress analysis according to ASME VIII rules, to evaluate resistance to plastic collapse including localized stress concentrations; and, finally, a detailed analysis with bolted fasteners in order to evaluate the behavior of the flanges, assuring the integrity of the vacuum sealing welds of the cryostat vessel body.

Comparison study of multistep forging and injection forging of automobile fasteners

OpenAIRE

Chen Senyong; Qin Yi

2015-01-01

In order to improve production efficiency, injection forging as a feasible approach was introduced to automobile fasteners production. In the study reported in this paper, two forging approaches, traditional multistep forging and injection forging, were analysed by using a finite element method. Using ABAQUS and DEFORM, some significant factors, namely, forging force, energy consumption, component accuracy and stress distribution in the die, were compared to explore the potential and challeng...

Accelerator System Model (ASM) user manual with physics and engineering model documentation. ASM version 1.0

International Nuclear Information System (INIS)

1993-07-01

The Accelerator System Model (ASM) is a computer program developed to model proton radiofrequency accelerators and to carry out system level trade studies. The ASM FORTRAN subroutines are incorporated into an intuitive graphical user interface which provides for the open-quotes constructionclose quotes of the accelerator in a window on the computer screen. The interface is based on the Shell for Particle Accelerator Related Codes (SPARC) software technology written for the Macintosh operating system in the C programming language. This User Manual describes the operation and use of the ASM application within the SPARC interface. The Appendix provides a detailed description of the physics and engineering models used in ASM. ASM Version 1.0 is joint project of G. H. Gillespie Associates, Inc. and the Accelerator Technology (AT) Division of the Los Alamos National Laboratory. Neither the ASM Version 1.0 software nor this ASM Documentation may be reproduced without the expressed written consent of both the Los Alamos National Laboratory and G. H. Gillespie Associates, Inc

Accelerator System Model (ASM) user manual with physics and engineering model documentation. ASM version 1.0

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-07-01

The Accelerator System Model (ASM) is a computer program developed to model proton radiofrequency accelerators and to carry out system level trade studies. The ASM FORTRAN subroutines are incorporated into an intuitive graphical user interface which provides for the {open_quotes}construction{close_quotes} of the accelerator in a window on the computer screen. The interface is based on the Shell for Particle Accelerator Related Codes (SPARC) software technology written for the Macintosh operating system in the C programming language. This User Manual describes the operation and use of the ASM application within the SPARC interface. The Appendix provides a detailed description of the physics and engineering models used in ASM. ASM Version 1.0 is joint project of G. H. Gillespie Associates, Inc. and the Accelerator Technology (AT) Division of the Los Alamos National Laboratory. Neither the ASM Version 1.0 software nor this ASM Documentation may be reproduced without the expressed written consent of both the Los Alamos National Laboratory and G. H. Gillespie Associates, Inc.

Forging Long Shafts On Disks

Science.gov (United States)

Tilghman, Chris; Askey, William; Hopkins, Steven

1989-01-01

Isothermal-forging apparatus produces long shafts integral with disks. Equipment based on modification of conventional isothermal-forging equipment, required stroke cut by more than half. Enables forging of shafts as long as 48 in. (122 cm) on typical modified conventional forging press, otherwise limited to making shafts no longer than 18 in. (46cm). Removable punch, in which forged material cools after plastic deformation, essential novel feature of forging apparatus. Technology used to improve such products as components of gas turbines and turbopumps and of other shaft/disk parts for powerplants, drive trains, or static structures.

Precision forging technology for aluminum alloy

Science.gov (United States)

Deng, Lei; Wang, Xinyun; Jin, Junsong; Xia, Juchen

2018-03-01

Aluminum alloy is a preferred metal material for lightweight part manufacturing in aerospace, automobile, and weapon industries due to its good physical properties, such as low density, high specific strength, and good corrosion resistance. However, during forging processes, underfilling, folding, broken streamline, crack, coarse grain, and other macro- or microdefects are easily generated because of the deformation characteristics of aluminum alloys, including narrow forgeable temperature region, fast heat dissipation to dies, strong adhesion, high strain rate sensitivity, and large flow resistance. Thus, it is seriously restricted for the forged part to obtain precision shape and enhanced property. In this paper, progresses in precision forging technologies of aluminum alloy parts were reviewed. Several advanced precision forging technologies have been developed, including closed die forging, isothermal die forging, local loading forging, metal flow forging with relief cavity, auxiliary force or vibration loading, casting-forging hybrid forming, and stamping-forging hybrid forming. High-precision aluminum alloy parts can be realized by controlling the forging processes and parameters or combining precision forging technologies with other forming technologies. The development of these technologies is beneficial to promote the application of aluminum alloys in manufacturing of lightweight parts.

AIS ASM Operational Integration Plan

Science.gov (United States)

2013-08-01

Rack mount computer AIS Radio Interface Ethernet Switch 192.168.0.x Firewall Cable Modem 192.168.0.1 VTS Accred. Boundary AIS ASM Operational... AIS ASM Operational Integration Plan Distribution Statement A: Approved for public release; distribution is unlimited. August 2013 Report No...CD-D-07-15 AIS ASM Operational Integration Plan ii UNCLAS//Public | CG-926 R&DC | I. Gonin, et al. | Public August 2013 N O T I C

CONAGT's place in ASME's centennial year

International Nuclear Information System (INIS)

Miller, W.H. Jr.

1985-01-01

A status report on ASME's Committee on Nuclear Air and Gas Treatment (CONAGT) is presented. This year ASME celebrates its centennial while CONAGT issues its first code sections covering fans, blowers, and refrigeration equipment. Significant code related CONAGT activities are covered as well as an explanation of CONAGT's place in the ASME organization

Properties of powder metallurgy steel forgings

International Nuclear Information System (INIS)

Crowson, A.; Anderson, F.E.

1977-01-01

The effects of processing variables on the mechanical properties of heat-treated powder metallurgy (P/M) steel forgings were determined. Prealloyed 4600 steel powder blended with graphite to yield 4640 was compacted into preforms and hot forged in a warm, closed die. Variables studied were preform density, method of lubrication, preform sintering (time, temperature and atmosphere), forging pressure (20 and 40 tsi) and temperature (1850 0 F, 2000 0 F and 2200 0 F), and forging ratio (0.75 and 0.95). Relationships between interconnected porosity and total porosity for the various preform densities were determined. High density compacts required higher sintering temperatures due to the restricted mobility of the reducing gases in the pores. Die wall lubrication was comparable to admixed lubrication, and it simplified powder mixing and preform sintering operations. Forgings with densities from 99 to 99.8 percent of theoretical density were attained with a forging pressure of 20 to 40 tsi and preform temperatures of 2000 0 F and above. At forging conditions which resulted in forgings with acceptable mechanical properties, complete die fill was accomplished at a forging ratio of 0.95, whereas incomplete die fill resulted at a forging ratio of 0.75. The response of P/M forgings to heat treatment was comparable to that for wrought materials, and the resultant tensile and yield strengths were equivalent to the strength values described for wrought 4640 steel in AMS specification 6317B. In addition, ductility and impact properties of P/M forgings with near theoretical density (99.5+ percent) were comparable to bar stock forgings

Manufacturing of ultra-large diameter 20 MnMoNi 5 5 steel forgings for reactor pressure vessels and their properties

International Nuclear Information System (INIS)

Onodera, S.; Kawaguchi, S.; Tsukada, H.; Moritani, H.; Suzuki, K.; Sato, I.

1985-01-01

As the structural material for RPV typical of increased dimensions, as set of ultra-large diameter steel forgings for a PHWR RPV is presented as outlined below. (1) Material designation: 20 MnMoNi 5 5 (similar to SA508, Cl.3) (2) Size of the forgings: flanges, 8.440 mm OD, a weight of 238 tons for shell flange; shells and torus, 7,920 mm OD, with large height, cover dome, 6,800 mm OD in chord and 460 mm thick; blank before formed to dome is ca. 8,000 mm OD. (3) Chemical composition: particular effort was made for minimizing the tramp elements as P, S, As, Sn, Sb, Cu. (4) Manufacturing, key points: steel making - combined refining and degassing in ladle; ingot making - largest size ingots, including 570 ton and 500 ton ingots; forging - special ''outside-the-press'' forging and forming techniques; heat treatment - prevention of H 2 flaking in normalizing and tempering and handling of the extra-large forgings at water quenching. (5) Metallurgical properties: sufficiently uniform carbon distributions in the forgings; a lowest possible content of hydrogen, non-metallic inclusions and oxygen. Mechanical properties: uniformity in tensile and toughness properties; flaws - only limited number of spots of UT indications under 2 mm EFG (EFS). (orig.)

Forging evaluaion of 304L stainless steel

International Nuclear Information System (INIS)

Packard, C.L.; Edstrom, C.M.

1979-01-01

The objective of this project was to evaluate and characterize the effects of various forging parameters on the metallographic structure and mechanical properties of 304L stainless steel forgings. Upset and die forgings were produced by hammer and Dynapak forging with forging temperatures ranging from 760 to 1145 0 C, upset reductions ranging from 20 to 60%, and annealing times ranging from 0 to 25 minutes at 843 0 C. The carbide precipitation behavior observed was found to be a function of forging temperature and annealing time. Higher forging temperatures were beneficial in avoiding continuous carbide precipitation and annealing at 843 0 C promoted increased carbide precipitation. The yield strength of the unannealed forgings decreased with increasing forging temperature and, with the exception of the 1145 0 C upset forgings, was significantly lowered by annealing

Nondestructive testing standards and the ASME code

International Nuclear Information System (INIS)

Spanner, J.C.

1991-04-01

Nondestructive testing (NDT) requirements and standards are an important part of the ASME Boiler and Pressure Vessel Code. In this paper, the evolution of these requirements and standards is reviewed in the context of the unique technical and legal stature of the ASME Code. The coherent and consistent manner by which the ASME Code rules are organized is described, and the interrelationship between the various ASME Code sections, the piping codes, and the ASTM Standards is discussed. Significant changes occurred in ASME Sections 5 and 11 during the 1980s, and these are highlighted along with projections and comments regarding future trends and changes in these important documents. 4 refs., 8 tabs

The ASME Code today -- Challenges, threats, opportunities

International Nuclear Information System (INIS)

Canonico, D.A.

1995-01-01

Since its modest beginning as a single volume in 1914 the ASME Code, or some of its parts, is recognized today in 48 of the United States and all providence's of Canada. The ASME Code today is composed of 25 books including two Code Case books. These books cover the new construction of boilers and pressure vessels and the new construction and In-Service-Inspection of Nuclear Power Plant components. The ASME accredits all manufacturers of boilers and pressure vessels built to the ASME Code. There are approximately 7650 symbol stamps issued throughout the world. Over 23% of the symbol stamps have been issued outside the USA and Canada. The challenge to the ASME Code is to be accepted as the world standard for pressure boundary components. There are activities underway to achieve that goal. The ASME Code is being revised to make it a more friendly document to entities outside of North America. To achieve that end there are specific tasks underway which are described here

Modelling of defects in ingot forging

DEFF Research Database (Denmark)

Christiansen, Peter

The present report presents an investigation of the ingot forging process with special emphasis on modelling the influence of die geometry on the soundness of the ingot after hot forging. An investigation on how to model damage is also performed. The influence of the lower die angle is quantified...... angle of 130o-140o giving rise to the largest centreline porosity closure regardless of material hardening behaviour applied. Friction was found only to have minor influence on the optimum. Multi stroke forging operations have also been modelled since the ingot forging process consists of many forging...... damage. It is found that when evaluating damage only by relative density; feed size and lower die angle does not influence whether the hot forging process is successful or not. This is in disagreement with the general understanding of the ingot forging process. When evaluating ductile damage...

Forging Industry Leadtimes: An Analysis of Causes for and Solutions to Long Leadtimes for Aerospace Forgings

Science.gov (United States)

1986-09-01

Pamplet . Forging Industry Association, Cleveland-MT, uncatea. 20. Forging Industry Association, and American Society for Metals. Forging Handbook, edited... Pamplet . The Harris-Thomas Drop Forge Compnyayto--n R, undated. 43. Theeck, Michael F., TECH MOD Program Mana.er. Personal interview. Industrial Base... Brochure . Worcester MA, 3, . 125 "’ VITA Captain Stephen F. O’Neill was born on 19 June 1957 in Pittsfield, Massachusetts. He graduated from high school

The influence of main parameters of the process of forging on the initial quality of forging for steel 35HM

International Nuclear Information System (INIS)

Banaszek, G.; Dyja, H.; Berski, S.

2001-01-01

The article discuss the effect of the main forging parameters and the selection of tools on improving the internal quality of forgings and closing up discontinuities of metallurgical origin during forging. As a result of investigations, the optimal values of the main technological parameters of forging have been determined and the application of an appropriate group of tools have been proposed for the flat die forging of forgings. (author)

Microstructure Evolution and Surface Cracking Behavior of Superheavy Forgings during Hot Forging

Directory of Open Access Journals (Sweden)

Zhenhua Wang

2018-01-01

Full Text Available In recent years, superheavy forgings that are manufactured from 600 t grade ingots have been applied in the latest generation of nuclear power plants to provide good safety. However, component production is pushing the limits of the current free-forging industry. Large initial grain sizes and a low strain rate are the main factors that contribute to the deformation of superheavy forgings during forging. In this study, 18Mn18Cr0.6N steel with a coarse grain structure was selected as a model material. Hot compression and hot tension tests were conducted at a strain rate of 10−4·s−1. The essential nucleation mechanism of the dynamic recrystallization involved low-angle grain boundary formation and subgrain rotation, which was independent of the original high-angle grain boundary bulging and the presence of twins. Twins were formed during the growth of dynamic recrystallization grains. The grain refinement was not obvious at 1150°C. A lowering of the deformation temperature to 1050°C resulted in a fine grain structure; however, the stress increased significantly. Crack-propagation paths included high-angle grain boundaries, twin boundaries, and the insides of grains, in that order. For superheavy forging, the ingot should have a larger height and a smaller diameter.

Microstructural and mechanical evolutions during the forging step of the COBAPRESS, a casting/forging process

Science.gov (United States)

Perrier, Frédéric; Desrayaud, Christophe; Bouvier, Véronique

Aluminum casting/forging processes are used to produce parts for the automotive industry. In this study, we examined the influence of the forging step on the microstructure and the mechanical properties of an A356 aluminum alloy modified with strontium. Firstly, a design of samples which allows us to test mechanically the alloy before and after forging was created. A finite element analysis with the ABAQUS software predicts a maximum of strain in the core of the specimens. Observations with the EBSD technique confirm a more intense sub-structuration of the dendrite cells in this zone. Yield strength, ultimate tensile strength, elongation and fatigue lives were then improved for the casting/forging samples compared to the only cast specimens. The closure of the porosities and the improvement of the surface quality during the forging step enhance also the fatigue resistance of the samples.

Globalization of ASME Nuclear Codes and Standards

International Nuclear Information System (INIS)

Swayne, Rick; Erler, Bryan A.

2006-01-01

With the globalization of the nuclear industry, it is clear that the reactor suppliers are based in many countries around the world (such as United States, France, Japan, Canada, South Korea, South Africa) and they will be marketing their reactors to many countries around the world (such as US, China, South Korea, France, Canada, Finland, Taiwan). They will also be fabricating their components in many different countries around the world. With this situation, it is clear that the requirements of ASME Nuclear Codes and Standards need to be adjusted to accommodate the regulations, fabricating processes, and technology of various countries around the world. It is also very important for the American Society of Mechanical Engineers (ASME) to be able to assure that products meeting the applicable ASME Code requirements will provide the same level of safety and quality assurance as those products currently fabricated under the ASME accreditation process. To do this, many countries are in the process of establishing or changing their regulations, and it is important for ASME to interface with the appropriate organizations in those countries, in order to ensure there is effective use of ASME Codes and standards around the world. (authors)

ASM observations of X-ray flares from 4U 0115+63 and ASM 1354-64.

Science.gov (United States)

Tsunemi, H.; Kitamoto, S.

The authors report two X-ray flares detected with the All Sky Monitor (ASM) on board the GINGA satellite. One is from the recurrent X-ray pulsar 4U 0115+63 and the other is from the probable recurrent X-ray nova named ASM 1354-64. The maximum intensity for 4U 0115+63 was 180 mCrab and its duration was at least 22 days. Its spectrum was hard and resembled those of X-ray pulsars. The maximum intensity of ASM 1354-64 was 300 mCrab. It faded down below the detection limit at the end of August 1987. Its spectrum was soft and was similar to those of black hole candidates.

New Trends in Forging Technologies

Science.gov (United States)

Behrens, B.-A.; Hagen, T.; Knigge, J.; Elgaly, I.; Hadifi, T.; Bouguecha, A.

2011-05-01

Limited natural resources increase the demand on highly efficient machinery and transportation means. New energy-saving mobility concepts call for design optimisation through downsizing of components and choice of corrosion resistant materials possessing high strength to density ratios. Component downsizing can be performed either by constructive structural optimisation or by substituting heavy materials with lighter high-strength ones. In this context, forging plays an important role in manufacturing load-optimised structural components. At the Institute of Metal Forming and Metal-Forming Machines (IFUM) various innovative forging technologies have been developed. With regard to structural optimisation, different strategies for localised reinforcement of components were investigated. Locally induced strain hardening by means of cold forging under a superimposed hydrostatic pressure could be realised. In addition, controlled martensitic zones could be created through forming induced phase conversion in metastable austenitic steels. Other research focused on the replacement of heavy steel parts with high-strength nonferrous alloys or hybrid material compounds. Several forging processes of magnesium, aluminium and titanium alloys for different aeronautical and automotive applications were developed. The whole process chain from material characterisation via simulation-based process design to the production of the parts has been considered. The feasibility of forging complex shaped geometries using these alloys was confirmed. In spite of the difficulties encountered due to machine noise and high temperature, acoustic emission (AE) technique has been successfully applied for online monitoring of forging defects. New AE analysis algorithm has been developed, so that different signal patterns due to various events such as product/die cracking or die wear could be detected and classified. Further, the feasibility of the mentioned forging technologies was proven by means

Forging process design for risk reduction

Science.gov (United States)

Mao, Yongning

In this dissertation, forging process design has been investigated with the primary concern on risk reduction. Different forged components have been studied, especially those ones that could cause catastrophic loss if failure occurs. As an effective modeling methodology, finite element analysis is applied extensively in this work. Three examples, titanium compressor disk, superalloy turbine disk, and titanium hip prosthesis, have been discussed to demonstrate this approach. Discrete defects such as hard alpha anomalies are known to cause disastrous failure if they are present in those stress critical components. In this research, hard-alpha inclusion movement during forging of titanium compressor disk is studied by finite element analysis. By combining the results from Finite Element Method (FEM), regression modeling and Monte Carlo simulation, it is shown that changing the forging path is able to mitigate the failure risk of the components during the service. The second example goes with a turbine disk made of superalloy IN 718. The effect of forging on microstructure is the main consideration in this study. Microstructure defines the as-forged disk properties. Considering specific forging conditions, preform has its own effect on the microstructure. Through a sensitivity study it is found that forging temperature and speed have significant influence on the microstructure. In order to choose the processing parameters to optimize the microstructure, the dependence of microstructure on die speed and temperature is thoroughly studied using design of numerical experiments. For various desired goals, optimal solutions are determined. The narrow processing window of titanium alloy makes the isothermal forging a preferred way to produce forged parts without forging defects. However, the cost of isothermal forging (dies at the same temperature as the workpiece) limits its wide application. In this research, it has been demonstrated that with proper process design, the die

29 CFR 1910.218 - Forging machines.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Forging machines. 1910.218 Section 1910.218 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.218 Forging machines. (a... other identifier, for the forging machine which was inspected. (ii) Scheduling and recording the...

Wear Analysis of Die Inserts in the Hot Forging Process of a Forked Type Forging Using Reverse Scanning Techniques

Directory of Open Access Journals (Sweden)

Łukasz Dworzak

2017-12-01

Full Text Available This article presents a wear analysis of die inserts used in the hot forging process of a forked forging (yoke, an element applied in steering systems of passenger vehicles. Studies involved the application of an original reverse scanning method intended for rapid and reliable wear analysis of forging tools (with complicated shape affording easy assessment without the need to dismount tools from the forging unit. The developed method involves analysis of progressive wear of forging tools based on measurements (scanning of forgings periodically collected from the process and constitutes a useful tool for measurement and testing. As the authors’ earlier works have demonstrated, the proposed new approach to analysis of tool wear with the application of reverse 3D scanning has proven successful in multiple instances in the case of axially symmetrical objects. The presented results of studies indicate that it is possible to utilize the expanded method to analyze the lifetime of forging tools, including tools with complex geometry. Application of the reverse scanning method allows for continuous and practical monitoring of the condition of forging tools over the course of the forging process and should have a positive impact on improving production output and reducing production costs.

48 CFR 225.7102 - Forgings.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Forgings. 225.7102 Section 225.7102 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF... Forgings. ...

Modeling flow stress constitutive behavior of SA508-3 steel for nuclear reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Sun Mingyue, E-mail: mysun@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Luhan, Hao; Shijian, Li; Dianzhong, Li; Yiyi, Li [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China)

2011-11-15

Highlights: > A series of flow stress constitutive equations for SA508-3 steel were successfully established. > The experimental results under different conditions have validated the constitutive equations. > An industrial application of the model was present to simulate a large conical shell forging process. - Abstract: Based on the measured stress-strain curves under different temperatures and strain rates, a series of flow stress constitutive equations for SA508-3 steel were firstly established through the classical theories on work hardening and softening. The comparison between the experimental and modeling results has confirmed that the established constitutive equations can correctly describe the mechanical responses and microstructural evolutions of the steel under various hot deformation conditions. We further represented a successful industrial application of this model to simulate a forging process for a large conical shell used in a nuclear steam generator, which evidences its practical and promising perspective of our model with an aim of widely promoting the hot plasticity processing for heavy nuclear components of fission reactors.

Index to place of publication of ASME Papers, 1978--1988

International Nuclear Information System (INIS)

Youngen, G.K.

1990-06-01

This index is a list of American Society of Mechanical Engineers (ASME) Papers that are reprinted in the ASME Transactions series of journals. ASME Papers are often cited only by their paper number, making it difficult to determine if the article has ever appeared in print in the journal literature. This index will be useful for tracking down those papers published as journal articles by the ASME. It will also serve as a guide for retention for subscribers to the ASME Papers and Transaction Series. Paper numbers that appear in the journals may be weeded from the collection of ASME Papers

Reparation of damaged forging dies

Directory of Open Access Journals (Sweden)

Vukić Lazić

2015-03-01

Full Text Available The forging dies are in exploitation exposed to elevated temperatures and variable impact loads, both compressive and shear. Steels for manufacturing of these tools must endure those loads while maintaining mechanical properties and being resistant to wear and thermal fatigue. For those reasons, the alloyed steels are used for making the forging dies, though they have less weldability, because alloying increases proneness to hardening. Any reparatory hard facing (HF of the damaged dies would require the specially adjusted technology to the particular piece. In this paper reparatory hard facing of dies used for forging pieces in the automobile industry is considered. Prior to reparatory hard facing of the real tools, numerous experimental hard facings on models were performed. All the model hard facings were done on the same steels which were used for production of the real forging dies. To define the optimal hard facing technology one needs to derive the optimal combination of the adequate heat treatment(s, to select the proper filler metals and the welding procedure. The established optimal HF technology was applied to real forging dies whose service life was further monitored in conditions of exploitation

Forging of Advanced Disk Alloy LSHR

Science.gov (United States)

Gabb, Timothy P.; Gayda, John; Falsey, John

2005-01-01

The powder metallurgy disk alloy LSHR was designed with a relatively low gamma precipitate solvus temperature and high refractory element content to allow versatile heat treatment processing combined with high tensile, creep and fatigue properties. Grain size can be chiefly controlled through proper selection of solution heat treatment temperatures relative to the gamma precipitate solvus temperature. However, forging process conditions can also significantly influence solution heat treatment-grain size response. Therefore, it is necessary to understand the relationships between forging process conditions and the eventual grain size of solution heat treated material. A series of forging experiments were performed with subsequent subsolvus and supersolvus heat treatments, in search of suitable forging conditions for producing uniform fine grain and coarse grain microstructures. Subsolvus, supersolvus, and combined subsolvus plus supersolvus heat treatments were then applied. Forging and subsequent heat treatment conditions were identified allowing uniform fine and coarse grain microstructures.

Activated sludge model No. 2d, ASM2d

DEFF Research Database (Denmark)

Henze, M.

1999-01-01

The Activated Sludge Model No. 2d (ASM2d) presents a model for biological phosphorus removal with simultaneous nitrification-denitrification in activated sludge systems. ASM2d is based on ASM2 and is expanded to include the denitrifying activity of the phosphorus accumulating organisms (PAOs......). This extension of ASM2 allows for improved modeling of the processes, especially with respect to the dynamics of nitrate and phosphate. (C) 1999 IAWQ Published by Elsevier Science Ltd. All rights reserved....

Role of forgings in powder metallurgy industry

International Nuclear Information System (INIS)

Hayes, A.F.; DeRidder, A.J.

1975-01-01

Forging of powder metallurgy materials is discussed. Information and data are included on forging powder metallurgy W, Mo, In 100, Rene 95, Astroloy, Be, and Ti. It is noted that the combination of powder metallurgy and forging work provides the best product from standpoints of reproducibility, freedom from segregation, low scrap rate, and uniform mechanical properties. Experience is being used to develop contour forging from hot isostatic pressed billets or preforms. The quality of this product is under evaluation. Results show steady improvement and it is anticipated that continued effort will soon produce a reliable, less costly product. Forging can continue to be relied upon to correct subtle defects present in powder metallurgy material

Forging loads, deformation modes and fracture in axi-symmetrric closed die cold forging of sintered aluminium powder compacts

International Nuclear Information System (INIS)

Butt, M.A.; Ali, L.

2003-01-01

An experimental investigation into closed-die cold forging of sintered aluminium powder rod- shaped compacts was carried out. Axi-symmetric components were forged from sintered powder preforms with different initial diameter to height ratios. Different compaction pressures, sintering and lubrication conditions were used as variables during the investigations. Detailed observations were made on green/sintered density, compaction defects, forging loads, deformation modes and on the onset of fracture during progressive forging of sintered powder compacts. Experimental results obtained during the investigations have been presented and discussed in detail. (author)

An example of a component replacement when applying ASME N509 and ASME N510 to older ventilation systems

International Nuclear Information System (INIS)

Arndt, T.E.

1994-06-01

This paper presents an example of a component replacement (electric heater) when installed in an older ventilation system that was constructed before the issuance of ASME N509 and N510. Many of the existing ventilation systems at the Hanford Site were designed, fabricated, and installed before the issuance of ASME N509 and N510. Requiring the application of these codes to existing ventilation systems presents challenges to the engineer when design changes are needed. Although it may seem that the application of ASME N509 or N510 may be a hindrance at times, this does not need to occur. Proper preparation at the start of project or design modifications can minimize frustration to the engineer when it is judged that portions of ASME N509 and N510 do not apply in a particular application

Safety Analysis Report for the KRI-ASM Transport Package

Energy Technology Data Exchange (ETDEWEB)

Bang, K. S.; Lee, J. C.; Kim, D. H.; Park, H. Y.; Kim, J. B.; Kim, H. J.; Seo, K. S

2005-11-15

Safety evaluation for the KRI-ASM transport package to transport safely I-131, which is produced at HANARO research reactor in KAERI, was carried out. In the safety analyses results for the KRI-ASM transport package, all the maximum stresses as well as the maximum temperature of the surface are lower than their allowable limits. The safety tests were performed by using the test model of the KRI-ASM transport package. Leak Test was performed after drop test and penetration test, the measured leakage rate was lower than allowable leakage rate. It is revealed that the containment integrity of the KRI-ASM transport package is maintained. Therefore, it shows that the integrity of the KRI-ASM transport package is well maintained.

ASME Code requirements for multi-canister overpack design and fabrication

International Nuclear Information System (INIS)

SMITH, K.E.

1998-01-01

The baseline requirements for the design and fabrication of the MCO include the application of the technical requirements of the ASME Code, Section III, Subsection NB for containment and Section III, Subsection NG for criticality control. ASME Code administrative requirements, which have not historically been applied at the Hanford site and which have not been required by the US Nuclear Regulatory Commission (NRC) for licensed spent fuel casks/canisters, were not invoked for the MCO. As a result of recommendations made from an ASME Code consultant in response to DNFSB staff concerns regarding ASME Code application, the SNF Project will be making the following modifications: issue an ASME Code Design Specification and Design Report, certified by a Registered Professional Engineer; Require the MCO fabricator to hold ASME Section III or Section VIII, Division 2 accreditation; and Use ASME Authorized Inspectors for MCO fabrication. Incorporation of these modifications will ensure that the MCO is designed and fabricated in accordance with the ASME Code. Code Stamping has not been a requirement at the Hanford site, nor for NRC licensed spent fuel casks/canisters, but will be considered if determined to be economically justified

International Accreditation of ASME Codes and Standards

International Nuclear Information System (INIS)

Green, Mervin R.

1989-01-01

ASME established a Boiler Code Committee to develop rules for the design, fabrication and inspection of boilers. This year we recognize 75 years of that Code and will publish a history of that 75 years. The first Code and subsequent editions provided for a Code Symbol Stamp or mark which could be affixed by a manufacturer to a newly constructed product to certify that the manufacturer had designed, fabricated and had inspected it in accordance with Code requirements. The purpose of the ASME Mark is to identify those boilers that meet ASME Boiler and Pressure Vessel Code requirements. Through thousands of updates over the years, the Code has been revised to reflect technological advances and changing safety needs. Its scope has been broadened from boilers to include pressure vessels, nuclear components and systems. Proposed revisions to the Code are published for public review and comment four times per year and revisions and interpretations are published annually; it's a living and constantly evolving Code. You and your organizations are a vital part of the feedback system that keeps the Code alive. Because of this dynamic Code, we no longer have columns in newspapers listing boiler explosions. Nevertheless, it has been argued recently that ASME should go further in internationalizing its Code. Specifically, representatives of several countries, have suggested that ASME delegate to them responsibility for Code implementation within their national boundaries. The question is, thus, posed: Has the time come to franchise responsibility for administration of ASME's Code accreditation programs to foreign entities or, perhaps, 'institutes.' And if so, how should this be accomplished?

Recent technological developments in forging; Recentes avancos tecnologicos no forjamento

Energy Technology Data Exchange (ETDEWEB)

Schaeffer, Lirio [Rio Grande do Sul Univ., Porto Alegre, RS (Brazil). Programa de Pos-graduacao em Engenharia Metalurgica e dos Materiais

1987-12-31

Recent advances in the area of open and closed die forging are summarized and discussed. The use of computer and alternatives such as incremental forging, sinter forging, liquid forging and precision forging are the main items reviewed 11 refs., 10 figs.

Heavy forgings for reactor pressure vessels

International Nuclear Information System (INIS)

Cerjak, H.; Papouschek, F.

1979-01-01

The importance of forgings for an optimal design of nuclear components is described. Problems concerning the correlation of requirements, material behavior, fabrication and testing of forgings are discussed. (orig.) [de

Temporal Deductive Verification of Basic ASM Models

OpenAIRE

Daho, Hocine El-Habib; University of Oran; Benhamamouch, Djillali; University of Oran

2010-01-01

Abstract State Machines (ASMs, for short) provide a practical new computational model which has been applied in the area of software engineering for systems design and analysis. However, reasoning about ASM models occurs, not within a formal deductive system, but basically in the classical informal proofs style of mathematics. Several formal verification approaches for proving correctness of ASM models have been investigated. In this paper we consider the use of the TLA+logic for the deductive...

Meeting the difficulties of an ASME calibration for pipe welds

Energy Technology Data Exchange (ETDEWEB)

Ginzel, E., E-mail: eginzel@mri.on.ca [Materials Research Inst., Waterloo, Ontario (Canada); Ginzel, R.; Buchholz, J., E-mail: rginzel@eclipsescientific.com [Eclipse Scientific, Waterloo, Ontario (Canada)

2013-11-15

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code Section V deals with Non-Destructive Testing (NDT). In North America the use of ASME Sec. V is not always limited to just ASME regulated projects. Even such seemingly unrelated Standards as CSA Z662 (the Canadian construction standard for Oil and Gas Pipeline Systems) references this document for some aspects of the NDT. ASME has several codes that are dedicated to piping welds, for example ASME 31.1, 31.3 and 31.8. All of them reference back to ASME Section V Article 4 for the accepted techniques to use when UT is the examination option, but sometimes ASME is not very helpful. As they try to leave options open in one area they close the doors in others, or so it seems when reading the clauses as mandatory where you see the word 'shall'. This paper will attempt to layout the issues with pipe weld inspections as per Article 4, 2011 edition. Like all other codes and standards, ASME is a regulated standard that is regularly reviewed and updated, and one must be careful to reference the year of the edition being used. For the purposes of this paper we have used the 2010/11 edition. (author)

Meeting the difficulties of an ASME calibration for pipe welds

International Nuclear Information System (INIS)

Ginzel, E.; Ginzel, R.; Buchholz, J.

2013-01-01

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code Section V deals with Non-Destructive Testing (NDT). In North America the use of ASME Sec. V is not always limited to just ASME regulated projects. Even such seemingly unrelated Standards as CSA Z662 (the Canadian construction standard for Oil and Gas Pipeline Systems) references this document for some aspects of the NDT. ASME has several codes that are dedicated to piping welds, for example ASME 31.1, 31.3 and 31.8. All of them reference back to ASME Section V Article 4 for the accepted techniques to use when UT is the examination option, but sometimes ASME is not very helpful. As they try to leave options open in one area they close the doors in others, or so it seems when reading the clauses as mandatory where you see the word 'shall'. This paper will attempt to layout the issues with pipe weld inspections as per Article 4, 2011 edition. Like all other codes and standards, ASME is a regulated standard that is regularly reviewed and updated, and one must be careful to reference the year of the edition being used. For the purposes of this paper we have used the 2010/11 edition. (author)

Modeling flow stress constitutive behavior of SA508-3 steel for nuclear reactor pressure vessels

International Nuclear Information System (INIS)

Sun Mingyue; Hao Luhan; Li Shijian; Li Dianzhong; Li Yiyi

2011-01-01

Highlights: → A series of flow stress constitutive equations for SA508-3 steel were successfully established. → The experimental results under different conditions have validated the constitutive equations. → An industrial application of the model was present to simulate a large conical shell forging process. - Abstract: Based on the measured stress-strain curves under different temperatures and strain rates, a series of flow stress constitutive equations for SA508-3 steel were firstly established through the classical theories on work hardening and softening. The comparison between the experimental and modeling results has confirmed that the established constitutive equations can correctly describe the mechanical responses and microstructural evolutions of the steel under various hot deformation conditions. We further represented a successful industrial application of this model to simulate a forging process for a large conical shell used in a nuclear steam generator, which evidences its practical and promising perspective of our model with an aim of widely promoting the hot plasticity processing for heavy nuclear components of fission reactors.

Updating of ASME Nuclear Code Case N-201 to Accommodate the Needs of Metallic Core Support Structures for High Temperature Gas Cooled Reactors Currently in Development

International Nuclear Information System (INIS)

Basol, Mit; Kielb, John F.; MuHooly, John F.; Smit, Kobus

2007-01-01

On September 29, 2005, ASME Standards Technology, LLC (ASME ST-LLC) executed a multi-year, cooperative agreement with the United States DOE for the Generation IV Reactor Materials project. The project's objective is to update and expand appropriate materials, construction, and design codes for application in future Generation IV nuclear reactor systems that operate at elevated temperatures. Task 4 was embarked upon in recognition of the large quantity of ongoing reactor designs utilizing high temperature technology. Since Code Case N-201 had not seen a significant revision (except for a minor revision in September, 2006 to change the SA-336 forging reference for 304SS and 316SS to SA-965 in Tables 1.2(a) and 1.2(b), and some minor editorial changes) since December 1994, identifying recommended updates to support the current high temperature Core Support Structure (CSS) designs and potential new designs was important. As anticipated, the Task 4 effort identified a number of Code Case N-201 issues. Items requiring further consideration range from addressing apparent inconsistencies in definitions and certain material properties between CC-N-201 and Subsection NH, to inclusion of additional materials to provide the designer more flexibility of design. Task 4 developed a design parameter survey that requested input from the CSS designers of ongoing high temperature gas cooled reactor metallic core support designs. The responses to the survey provided Task 4 valuable input to identify the design operating parameters and future needs of the CSS designers. Types of materials, metal temperature, time of exposure, design pressure, design life, and fluence levels were included in the Task 4 survey responses. The results of the survey are included in this report. This research proves that additional work must be done to update Code Case N-201. Task 4 activities provide the framework for the Code Case N-201 update and future work to provide input on materials. Candidate

Brittle Fracture Behaviors of Large Die Holders Used in Hot Die Forging

Directory of Open Access Journals (Sweden)

Weifang Zhang

2017-05-01

Full Text Available Brittle fracture of large forging equipment usually leads to catastrophic consequences. To avoid this kind of accident, the brittle fracture behaviors of a large die holder were studied by simulating the practical application. The die holder is used on the large die forging press, and it is made of 55NiCrMoV7 hot-work tool steel. Detailed investigations including mechanical properties analysis, metallographic observation, fractography, transmission electron microscope (TEM analysis and selected area electron diffraction (SAED were conducted. The results reveal that the material generated a large quantity of large size polyhedral M23C6 (M: Fe and Cr mainly and elongated M3C (M: Fe mainly carbides along the martensitic lath boundaries when the die holder was recurrently tempered and water-cooled at 250 °C during the service. The large size carbides lead to the material embrittlement and impact toughness degradation, and further resulted in the brittle fracture of the die holder. Therefore, the operation specification must be emphasized to avoid the die holder being cooled by using water, which is aimed at accelerating the cooling.

An example of a component replacement when applying ASME N509 and ASME N510 to older ventilation systems

Energy Technology Data Exchange (ETDEWEB)

Arndt, T.E. [Westinghouse Hanford Company, Richland, WA (United States)

1995-02-01

This paper presents an example of a component replacement (electric heater) when installed in an older ventilation system that was constructed before the issuance of ASME N509{sup 1} and N510{sup 2}. Many of the existing ventilation systems at the Hanford Site were designed, fabricated, and installed before the issuance of ASME N509{sup 1} and N510{sup 2}. Requiring the application of these codes to existing ventilation systems presents challenges to the engineer when design changes are needed. Although it may seem that the application of ASME N509{sup 1} or N510{sup 2} may be a hindrance at times, this does not need to occur. Proper preparation at the start of project or design modifications can minimize frustration to the engineer when it is judged that portions of ASME N509{sup 1} and N510{sup 2} do not apply in a particular application.

Forging technology for large nuclear pressure vessel parts

International Nuclear Information System (INIS)

Kakimoto, Hideki; Ikegami, Tomonori

2014-01-01

The increasing output of nuclear power generation calls for larger vessels for next-generation nuclear power plants. A vessel with an increased diameter requires increased load for its forging, which can make it difficult to use a conventional solid die. In order to reduce the forging load, a rotary incremental forging method has been applied to hot forging. This method includes pressing and rotating a material in an incremental manner such that a target shape is obtained. This study aimed at improving the accuracy of numerical simulation for the rotary incremental forging to reduce the load when forging large vessels. This has enabled the temperature of the material and flow stress to be precisely predicted; an example of this is reported in the paper. Specifically, the heat transfer coefficient to be used for the numerical simulation had been determined experimentally from a small-scale hot-forging. The reduction of the flow stress associated with incremental forging, had been deduced from a compression test, and the value was applied to the numerical simulation. A preform was designed on the basis of the above simulation to perform a 1/1 size scale experiment. A precision of better than 5% has been confirmed for the shape prediction. (author)

Review of ASME-NH Design Materials for Creep-Fatigue

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Kim, Jong Bum

2010-01-01

To review and recommend the candidate design materials for the Sodium-Cooled Fast Reactor, the material sensitivity evaluations by the comparison of design data between the ASME-NH materials were performed by using the SIE ASME-NH computer program implementing the material database of the ASME-NH. The design material data provided by the ASME-NH code are the elastic modulus and yield Strength, Time-Independent Allowable Stress Intensity value, time-dependent allowable stress intensity value, expected minimum stress-to rupture value, stress rupture Factors for weldment, isochronous stress-strain curves, and design fatigue curves. Among these, the data related with the creep-fatigue evaluation are investigated in this study

International cooperation in cold forging technology

DEFF Research Database (Denmark)

Bay, Niels; Lange, K

1992-01-01

International cooperation in the field of cold forging technology started in 1961 by formation of the OECD Group of Experts on Metal Forming. In 1967 this group was transformed into the International Cold Forging Group, ICFG, an independent body which has now been operative for 25 years. Members...... of the ICFG are personally elected by the Plenary as experts within the field, often representing national groups within cold forging. The main work within the ICFG is carried out in its subgroups which are established by the Plenary to collect, compile and evaluate data and eventually also produce data...... by cooperative activities or by instigating national research. These subgroups have produced 9 data sheets and 7 guidelines on subjects such as materials, tool design and construction, calculation methods for cold forging tools, manufacture of slugs, lubrication aspects and small quantity production. Plenary...

Cisco ASM Router

CERN Multimedia

2001-01-01

One of the two "ASM/2-32EM" boxes installed in 1988, from "Cisco Systems Inc." - then an unknown 20-employee company in Menlo Park, California (USA). This is one of the first two Cisco boxes to appear in Switzerland, and possibly Europe. The 220v power supply was a special modification made for use at CERN. They supported IP address filtering, which seemed just what CERN needed to help protect the new Cray XMP-48 super computer from network hackers. The two ASM boxes were both routers and terminal servers. They protected a secure private Ethernet segment used by the Cray project, as well as providing secure terminal connections to that segment, including CERN's first dialback terminal service, which allowed Cray and CERN system analysts to work on the machine from home, using another Cisco feature called TACACS. (Kindly offered by B. Segal who discovered this company while at a Usenix Conference in Phoenix, Arizona in June 1987.)

Report on the Current Technical Issues on ASME Nuclear Code and Standard

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2008-11-01

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

Regulation of dynein-mediated autophagosomes trafficking by ASM in CASMCs.

Science.gov (United States)

Xu, Ming; Zhang, Qiufang; Li, Pin-Lan; Nguyen, Thaison; Li, Xiang; Zhang, Yang

2016-01-01

Acid sphingomyelinase (ASM; gene symbol Smpd1) has been shown to play a crucial role in autophagy maturation by controlling lysosomal fusion with autophagosomes in coronary arterial smooth muscle cells (CASMCs). However, the underlying molecular mechanism by which ASM controls autophagolysosomal fusion remains unknown. In primary cultured CASMCs, lysosomal Ca2+ induced by 7-ketocholesterol (7-Ket, an atherogenic stimulus and autophagy inducer) was markedly attenuated by ASM deficiency or TRPML1 gene silencing suggesting that ASM signaling is required for TRPML1 channel activity and subsequent lysosomal Ca(2+) release. In these CASMCs, ASM deficiency or TRPML1 gene silencing markedly inhibited 7-Ket-induced dynein activation. In addition, 7-Ket-induced autophagosome trafficking, an event associated with lysosomal Ca(2+) release and dynein activity, was significantly inhibited in ASM-deficient (Smpd1(-/-)) CASMCs compared to that in Smpd1(+/+) CASMCs. Finally, overexpression of TRPML1 proteins restored 7-Ket-induced lysosomal Ca(2+) release and autophagosome trafficking in Smpd1-/- CASMCs. Collectively, these results suggest that ASM plays a critical role in regulating lysosomal TRPML1-Ca(2+) signaling and subsequent dynein-mediated autophagosome trafficking, which leads its role in controlling autophagy maturation in CASMCs under atherogenic stimulation.

Hot forging of roll-cast high aluminum content magnesium alloys

Science.gov (United States)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

ASME nuclear codes and standards risk management strategic planning

International Nuclear Information System (INIS)

Hill, Ralph S. III; Balkey, Kenneth R.; Erler, Bryan A.; Wesley Rowley, C.

2007-01-01

This paper is prepared in honor and in memory of the late Professor Emeritus Yasuhide Asada to recognize his contributions to ASME Nuclear Codes and Standards initiatives, particularly those related to risk-informed technology and System Based Code developments. For nearly two decades, numerous risk-informed initiatives have been completed or are under development within the ASME Nuclear Codes and Standards organization. In order to properly manage the numerous initiatives currently underway or planned for the future, the ASME Board on Nuclear Codes and Standards (BNCS) has an established Risk Management Strategic Plan (Plan) that is maintained and updated by the ASME BNCS Risk Management Task Group. This paper presents the latest approved version of the plan beginning with a background of applications completed to date, including the recent probabilistic risk assessment (PRA) standards developments for nuclear power plant applications. The paper discusses planned applications within ASME Nuclear Codes and Standards that will require expansion of the ASME PRA Standard to support new advanced light water reactor and next generation reactor developments, such as for high temperature gas-cooled reactors. Emerging regulatory developments related to risk-informed, performance- based approaches are summarized. A long-term vision for the potential development and evolution to a nuclear systems code that adopts a risk-informed approach across a facility life-cycle (design, construction, operation, maintenance, and closure) is also summarized. Finally, near term and long term actions are defined across the ASME Nuclear Codes and Standards organizations related to risk management, including related U.S. regulatory activities. (author)

AsmL Specification of a Ptolemy II Scheduler

DEFF Research Database (Denmark)

Lázaro Cuadrado, Daniel; Koch, Peter; Ravn, Anders Peter

2003-01-01

Ptolemy II is a tool that combines different computational models for simulation and design of embedded systems. AsmL is a software specification language based on the Abstract State Machine formalism. This paper reports on development of an AsmL model of the Synchronous Dataflow domain scheduler...

Press forging and optical properties of lithium fluoride

Science.gov (United States)

Ready, J. F.; Vora, H.

1980-07-01

Lithium fluoride is an important candidate material for windows on high power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals were press forged in one step over the temperature range 300 to 600 C to obtain fine grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40 percent at 400 C to 65 percent at 600 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 C, to total deformations of 69 to 76 percent, with intermediate annealing at 700 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one step forging. The results of characterization of various optical and mechanical properties of single crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described.

Press forging and optical properties of lithium fluoride

International Nuclear Information System (INIS)

Ready, J.F.; Vora, H.

1979-01-01

Lithium fluoride is an important candidate material for windows on high-power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals have been press forged in one step over the temperature range 300 to 600 0 c to obtain fine-grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40% at 400 0 C to 65% at 600 0 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 0 C, to total deformations of 69-76%, with intermediate annealing at 700 0 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one-step forging. The results of characterization of various optical and mechanical properties of single-crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described

Quality assurance for hammer forgings

International Nuclear Information System (INIS)

Potthast, E.

1984-01-01

The quality assurance program introduced by Arbed Saarstahl and laid down in a quality assurance manual is described. A particular attention is attached thereby both to quality practice proper and to a reliable flow of information amongst all the persons involved. The production and test sequence schedules of the hammer forging plant are illustrated by the example of a forged valve housing for nuclear power plants. These schedules specify not only the forging process in the individual production stages but also the workpiece contour after each working operation, the heat treatment, the furnace charging, and the inspection of finished parts. The formalization of the tests is designed both to promote the customer's trust towards the supplier and to prevent the formal operations involved from hindering further technical development. (orig.) [de

Co-Operative Training in the Sheffield Forging Industry

Science.gov (United States)

Duncan, R.

2008-01-01

Purpose: The purpose of this paper is to give details of an operation carried out in Sheffield to increase the recruitment of young men into the steel forging industry. Design/methodology/approach: The Sheffield Forges Co-operative Training Scheme was designed to encourage boys to enter the forging industry and to provide them with training and…

A user's perspective on the merits and shortcomings of ASME Section III

International Nuclear Information System (INIS)

Antaki, G.A.

1994-01-01

There are several aspects of Section III which when compared to process industry codes (ASME VIII, ASME B31.3, API, etc.) have proven to be a significant improvement in engineering practice. There are, however, other aspects of ASME III which have added to costs without clear benefits in safety or reliability. The authors present a user's perspective on some of the relative merits and shortcomings of the nuclear codes (ASME III and XI) compared to the process industry codes (such as ASME VIII, B31.3 and API)

Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

Energy Technology Data Exchange (ETDEWEB)

Seniuk, P.J.

1996-12-01

This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, {open_quotes}Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plants{close_quotes}. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O&M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O&M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion.

Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

International Nuclear Information System (INIS)

Seniuk, P.J.

1996-01-01

This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, open-quotes Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plantsclose quotes. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O ampersand M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O ampersand M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion

Application procedures and analysis examples of the SIE ASME-NH program

International Nuclear Information System (INIS)

Kim, Seok Hoon; Koo, G. H.; Kim, J. B.

2010-12-01

In this report, the design rule of the ASME-NH Code was briefly summarized and the application procedures of SIE ASME-NH program were analysed, the analysis examples were described. The SIE ASME-NH program was developed according to the ASME Code Section III Subsection NH rules to perform the primary stress limits, the accumulated inelastic strain limits and the creep fatigue damage evaluations in the structural design of nuclear power plants operating with high temperatures over creep temperature at normal operating conditions. In the analysis examples, the benchmark problem for the high temperature reactor vessel which was discussed in the SIE ASME-NH user's seminar was described. Also, the preliminary structural analysis of an Advanced Burner Test Reactor internal structure was described. Considering the load combinations of the various cycle types submitted from significant operating conditions, the integrity of a reactor internal structure was reviewed according to the stress and strain limits of the ASME-NH rules and the analysis and evaluation results were summarized

Development of integral type forgings for steam generator of nuclear power plant

International Nuclear Information System (INIS)

Suzuki, Komei; Sato, Ikuo; Murai, Etsuo

1992-01-01

The use of integral type steel forgings for the construction of pressure vessel enhances the structural integrity of components and makes the fabrication of components and the execution of in-service inspection (ISI) easier than those fabrication from plate and casting materials. Such steel forgings have been realized for steam generator (SG) for nuclear power plant as follows : (1) Forged shell ring : change from welding fabrication of formed plates to forging ; (2) Forged conical shell ring : ditto ; (3) Forged head integral with nozzles (s) : (i) Primary head : change from casting to forging ; (ii) Secondary head : change from welding fabrication of formed plates to forging. These steel forgings have been realized by recent development in manufacturing technologies, such as steel making, forging processes and heat treatment which are vital to the quality of steel forgings. Some examples of recent typical high quality steel forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced, and the main points of the manufacturing technique and the quality attained are also described. (author)

ASME nuclear codes and standards risk management strategic plan

International Nuclear Information System (INIS)

Balkey, Kenneth R.

2003-01-01

Over the past 15 years, several risk-informed initiatives have been completed or are under development within the ASME Nuclear Codes and Standards organization. In order to better manage the numerous initiatives in the future, the ASME Board on Nuclear Codes and Standards has recently developed and approved a Risk Management Strategic Plan. This paper presents the latest approved version of the plan beginning with a background of applications completed to date, including the recent issuance of the ASME Standard for Probabilistic Risk Assessment (PRA) for Nuclear Power Plant Applications. The paper discusses potential applications within ASME Nuclear Codes and Standards that may require expansion of the PRA Standard, such as for new generation reactors, or the development of new PRA Standards. A long-term vision for the potential development and evolution to a nuclear systems code that adopts a risk-informed approach across a facility life-cycle (design, construction, operation, maintenance, and closure) is summarized. Finally, near term and long term actions are defined across the ASME Nuclear Codes and Standards organizations related to risk management, and related U.S. regulatory activities are also summarized. (author)

Computer Program of SIE ASME-NH (Revision 1.0) Code

Energy Technology Data Exchange (ETDEWEB)

Koo, Gyeong Hoi; Lee, J. H

2008-01-15

In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail.

Computer Program of SIE ASME-NH (Revision 1.0) Code

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, J. H.

2008-01-01

In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail

Recent development in the ASME O and M committee codes, standards, and guides

International Nuclear Information System (INIS)

Rowley, C.W.

1999-01-01

The ASME O and M Committee continues to expand and update its code, standards, and guides as contained in the ASME OM Code and the ASME OM Standards/Guides. This paper will describe recent changes to these two ASME documents, including technical inquiries, code cases, and the major reformat of the ASME OM Code 1998 Edition. Also two new Parts to the ASME OM S/G will be discussed: OM Part 23 and OM Part 24, which are close to being initially published. A third new Part to the ASME OM S/G has been authorized and has recently started to get organized: Part 26, 'Thermal Calibration of RTDs'. In addition this paper will describe the future plans for these two documents as provided in the O and M Committee Strategic Plan. (author)

Future direction of ASME nuclear codes and standards

International Nuclear Information System (INIS)

Ennis, Kevin; Sheehan, Mark E.

2003-01-01

While the nuclear power industry in the US is in a period of stasis, there continues to be a great deal of activity in the ASME nuclear standards development arena. As plants age, the need for new approaches in standardization changes with the changing needs of the industry. New tools are becoming available in the form of risk analysis, and this is finding its way into more and more of ASME's standards activities. This paper will take a look at the direction that ASME nuclear Codes and Standards are heading in this and other areas, as well as taking a look at some advance reactor concepts and plans for standards to address new technologies

Phased Array Ultrasonic Inspection of Titanium Forgings

International Nuclear Information System (INIS)

Howard, P.; Klaassen, R.; Kurkcu, N.; Barshinger, J.; Chalek, C.; Nieters, E.; Sun, Zongqi; Fromont, F. de

2007-01-01

Aerospace forging inspections typically use multiple, subsurface-focused sound beams in combination with digital C-scan image acquisition and display. Traditionally, forging inspections have been implemented using multiple single element, fixed focused transducers. Recent advances in phased array technology have made it possible to perform an equivalent inspection using a single phased array transducer. General Electric has developed a system to perform titanium forging inspection based on medical phased array technology and advanced image processing techniques. The components of that system and system performance for titanium inspection will be discussed

22 CFR 121.10 - Forgings, castings and machined bodies.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Forgings, castings and machined bodies. 121.10... STATES MUNITIONS LIST Enumeration of Articles § 121.10 Forgings, castings and machined bodies. Articles on the U.S. Munitions List include articles in a partially completed state (such as forgings...

Kinematics at the Main Mechanism of a Railbound Forging Manipulator

Directory of Open Access Journals (Sweden)

Florian Ion Tiberiu Petrescu

2015-09-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Heavy payload forging manipulators are mainly characterized by large load output and large capacitive load input. The relationship between outputs and inputs will greatly influence the control and the reliability. Forging manipulators have become more prevalent in the industry today. They are used to manipulate objects to be forged. The most common forging manipulators are moving on a railway to have a greater precision and stability. They have been called the railbound forging manipulators. In this paper we analyze the general kinematics of the main mechanism from a such manipulator. Kinematic scheme shows a typical forging manipulator, with the basic motions in operation process: walking, motion of the tong and buffering. The lifting mechanism consists of several parts including linkages, hydraulic drives and motion pairs. The principle of type design from the viewpoints of the relationship between output characteristics and actuator inputs is discussed. An idea of establishing the incidence relationship between output characteristics and actuator inputs is proposed. These novel forging manipulators which satisfy certain functional requirements provide an effective help for the design of forging manipulators.

Study on the isothermal forging process of MB26 magnesium alloy adaptor

Directory of Open Access Journals (Sweden)

Xu Wenchen

2015-01-01

Full Text Available The isothermal forging process is an effective method to manufacture complex-shaped components of hard-to-work materials, such as magnesium alloys. This study investigates the isothermal forging process of an MB26 magnesium alloy adaptor with three branches. The results show that two-step forging process is appropriate to form the adaptor forging, which not only improves the filling quality but also reduces the forging load compared with one-step forging process. Moreover, the flow line is distributed along the contour of the complex-shaped adaptor forging.

Near-Net Forging Technology Demonstration Program

Science.gov (United States)

Hall, I. Keith

1996-01-01

Significant advantages in specific mechanical properties, when compared to conventional aluminum (Al) alloys, make aluminum-lithium (Al-Li) alloys attractive candidate materials for use in cryogenic propellant tanks and dry bay structures. However, the cost of Al-Li alloys is typically five times that of 2219 aluminum. If conventional fabrication processes are employed to fabricate launch vehicle structure, the material costs will restrict their utilization. In order to fully exploit the potential cost and performance benefits of Al-Li alloys, it is necessary that near-net manufacturing methods be developed to off-set or reduce raw material costs. Near-net forging is an advanced manufacturing method that uses elevated temperature metal movement (forging) to fabricate a single piece, near-net shape, structure. This process is termed 'near-net' because only a minimal amount of post-forge machining is required. The near-net forging process was developed to reduce the material scrap rate (buy-to-fly ratio) and fabrication costs associated with conventional manufacturing methods. The goal for the near-net forging process, when mature, is to achieve an overall cost reduction of approximately 50 percent compared with conventional manufacturing options for producing structures fabricated from Al-Li alloys. This NASA Marshall Space Flight Center (MSFC) sponsored program has been a part of a unique government / industry partnership, coordinated to develop and demonstrate near-net forging technology. The objective of this program was to demonstrate scale-up of the near-net forging process. This objective was successfully achieved by fabricating four integrally stiffened, 170- inch diameter by 20-inch tall, Al-Li alloy 2195, Y-ring adapters. Initially, two 2195 Al-Li ingots were converted and back extruded to produce four cylindrical blockers. Conventional ring rolling of the blockers was performed to produce ring preforms, which were then contour ring rolled to produce

27 CFR 447.22 - Forgings, castings, and machined bodies.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Forgings, castings, and... IMPLEMENTS OF WAR The U.S. Munitions Import List § 447.22 Forgings, castings, and machined bodies. Articles on the U.S. Munitions Import List include articles in a partially completed state (such as forgings...

The State of the Art in Cold Forging Lubrication

DEFF Research Database (Denmark)

Bay, Niels

1994-01-01

The manufature of components in steel, aluminium and copper alloys by cold forging production has increased ever since the 1950's. Typical processes are forward rod extrusion and backward can extrusion, upsetting, ironing, tube extrusion and radial extrusion. The tribological conditions in cold...... forging are extremely severe due to large surface expansion and normal pressure in the tool/workpiece interface combined with elevated tool temperatures. Except for the more simple cold forging operations successful production therefore requires advanced lubrication systems. The present paper gives...... a detailed description of the state of art for lubricant systems for cold forging of C-steels and low alloy steels as well as aluminium alloys including all the basic operations such as cleaning of the slugs, application of eventual conversion coating and lubrication. As regards cold forging of steel...

Penetration of ASM 981 in canine skin: a comparative study.

Science.gov (United States)

Gutzwiller, Meret E Ricklin; Reist, Martin; Persohn, Elke; Peel, John E; Roosje, Petra J

2006-01-01

ASM 981 has been developed for topical treatment of inflammatory skin diseases. It specifically inhibits the production and release of pro-inflammatory cytokines. We measured the skin penetration of ASM 981 in canine skin and compared penetration in living and frozen skin. To make penetration of ASM 981 visible in dog skin, tritium labelled ASM 981 was applied to a living dog and to defrosted skin of the same dog. Using qualitative autoradiography the radioactive molecules were detected in the lumen of the hair follicles until the infundibulum, around the superficial parts of the hair follicles and into a depth of the dermis of 200 to 500 microm. Activity could not be found in deeper parts of the hair follicles, the dermis or in the sebaceous glands. Penetration of ASM 981 is low in canine skin and is only equally spread in the upper third of the dermis 24 hours after application. Penetration in frozen skin takes even longer than in living canine skin but shows the same distribution.

ASME factory authorization system and the situation in Japan

International Nuclear Information System (INIS)

Futagawa, Kiyoshi

1978-01-01

Since about three or four years ago, the enterprises of machinery, iron and steel and welding materials in Japan are paying much attention to the acquisition of ASME (American Society of Mechanical Engineers) certificates or authorization to stamp the code symbols. That is, over 70 factories in Japan have undergone ASME examination, and consequently acquired the authorization or certificates. Such authorization is divided into over 20 kinds, of which about 7 are possessed by the companies in Japan. In nuclear field, the kinds of authorization are N (nuclear vessel), NPT (nuclear vessel parts), NV (nuclear vessel safety valve), and MM (material manufacturing). In non-nuclear fields, they are S (power boilers), U (pressure vessels, in Div. 1), and U2 (pressure vessels in Div. 2). The following matters are described: ASME setup, authorization procedures of ASME for factories, the kinds of authorization, factories in Japan holding the authorization or certificates, and renewal of the authorization. (Mori, K.)

Instant forgedUI starter

CERN Document Server

Luiz, Joseandro

2013-01-01

Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks.The book is a Starter guide to learning ForgedUI. This book will start by unfolding the installation and creating a simple application using Titanium and ForgedUI, followed by taking you through the features to model an engaging UI and generate multi-platform code with Titanium, while covering the best design practice for Apple and Android application development. Last but not least, you will also come across the available resources where you can

An empirical model for friction in cold forging

DEFF Research Database (Denmark)

Bay, Niels; Eriksen, Morten; Tan, Xincai

2002-01-01

With a system of simulative tribology tests for cold forging the friction stress for aluminum, steel and stainless steel provided with typical lubricants for cold forging has been determined for varying normal pressure, surface expansion, sliding length and tool/work piece interface temperature...... of normal pressure and tool/work piece interface temperature. The model is verified by process testing measuring friction at varying reductions in cold forward rod extrusion. KEY WORDS: empirical friction model, cold forging, simulative friction tests....

40 CFR 467.40 - Applicability; description of the forging subcategory.

Science.gov (United States)

2010-07-01

... forging subcategory. 467.40 Section 467.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Forging Subcategory § 467.40 Applicability; description of the forging subcategory. This subpart applies to discharges of...

Die forging of the alloys Az80 and Zk60

NARCIS (Netherlands)

Kurz, G.; Clauw, B.; Sillekens, W.H.; Letzig, D.

2009-01-01

Overall goal of the MagForge project is to provide tailored and cost-effective technologies for the industrial manufacturing of magnesium forged components. Scientific and technological aspects are new alloys/feedstock materials with improved performance, forging process modeling and design tools

Sintering and densification; new techniques: sinter forging

International Nuclear Information System (INIS)

Winnubst, A.J.A.

1998-01-01

In this chapter pressure assisted sintering methods will be described. Attention will mainly be paid to sinter forging as a die-wall free uniaxial pressure sintering technique, where large creep strains are possible. Sinter forging is an effective tool to reduce sintering temperature and time and to obtain a nearly theoretically dense ceramic. In this way grain size in tetragonal zirconia ceramics can be reduced down to 100 nm. Another important phenomenon is the reduction of the number density and size of cracks and flaws resulting in higher strength and improved reliability, which is of utmost importance for engineering ceramics. The creep deformation during sinter forging causes a rearrangement of the grains resulting in a reduction of interatomic spaces between grains, while grain boundary (glassy) phases can be removed. The toughness and in some cases the wear resistance is enhanced after sinter forging as a result of the grain-boundary-morphology improvement. (orig.)

Statistical analysis of the ASME KIc database

International Nuclear Information System (INIS)

Sokolov, M.A.

1998-01-01

The American Society of Mechanical Engineers (ASME) K Ic curve is a function of test temperature (T) normalized to a reference nil-ductility temperature, RT NDT , namely, T-RT NDT . It was constructed as the lower boundary to the available K Ic database. Being a lower bound to the unique but limited database, the ASME K Ic curve concept does not discuss probability matters. However, a continuing evolution of fracture mechanics advances has led to employment of the Weibull distribution function to model the scatter of fracture toughness values in the transition range. The Weibull statistic/master curve approach was applied to analyze the current ASME K Ic database. It is shown that the Weibull distribution function models the scatter in K Ic data from different materials very well, while the temperature dependence is described by the master curve. Probabilistic-based tolerance-bound curves are suggested to describe lower-bound K Ic values

Effect of Laser Preheating AISI 4140 Specimens for Micro-Forging

Directory of Open Access Journals (Sweden)

Jung C.

2017-06-01

Full Text Available Many high performance and permanent service parts require suitable material characteristics-high fatigue strength is one of the most important characteristics. For this reason, surface treatment processes are essential to increase the material performance and avoid the use of costly ineffective material. There exist various surface treatment processes for various applications. Each process has advantages and disadvantages and hybridization can solve various problems. The micro-forging process delivers a controlled and uniform surface hardness, but the depth of the forged surface is limited. On the other hand, laser heat treatment can increase the hardness drastically, but the surface may become brittle, which reduces the fatigue life. Laser-assisted micro-forging is a novel hybrid process of laser heat treatment and micro-forging that has the potential to increase the forging depth and relax the stress caused by the high temperature of the forging process.

ASME nuclear codes and standards: Scope of coverage and current initiatives

International Nuclear Information System (INIS)

Eisenberg, G. M.

1995-01-01

The objective of this paper is to address the broad scope of coverage of nuclear codes, standards and guides produced and administered by the American Society of Mechanical Engineers (ASME). Background information is provided regarding the evolution of the present activities. Details are provided on current initiatives intended to permit ASME to meet the needs of a changing nuclear industry on a worldwide scale. During the early years of commercial nuclear power, ASME produced a code for the construction of nuclear vessels used in the reactor coolant pressure boundary, containment and auxiliary systems. In response to industry growth, ASME Code coverage soon broadened to include rules for construction of other nuclear components, and inservice inspection of nuclear reactor coolant systems. In the years following this, the scope of ASME nuclear codes, standards and guides has been broadened significantly to include air cleaning activities for nuclear power reactors, operation and maintenance of nuclear power plants, quality assurance programs, cranes for nuclear facilities, qualification of mechanical equipment, and concrete reactor vessels and containments. ASME focuses on globalization of its codes, standards and guides by encouraging and promoting their use in the international community and by actively seeking participation of international members on its technical and supervisory committees and in accreditation activities. Details are provided on current international representation. Initiatives are underway to separate the technical requirements from administrative and enforcement requirements, to convert to hard metric units, to provide for non-U. S. materials, and to provide for translations into non-English languages. ASME activity as an accredited ISO 9000 registrar for suppliers of mechanical equipment is described. Rules are being developed for construction of containment systems for nuclear spent fuel and high-level waste transport packagings. Intensive

48 CFR 252.225-7025 - Restriction on acquisition of forgings.

Science.gov (United States)

2010-10-01

... of forgings. 252.225-7025 Section 252.225-7025 Federal Acquisition Regulations System DEFENSE... CLAUSES Text of Provisions And Clauses 252.225-7025 Restriction on acquisition of forgings. As prescribed in 225.7102-4, use the following clause: Restriction on Acquisition of Forgings (DEC 2009) (a...

Highlights of proposed changes to ANSI/ASME N509-80

International Nuclear Information System (INIS)

Ornberg, S.C.

1987-01-01

The ASME Committee on Nuclear Air and Gas Treatment (CONAGT) are at the time of this writing considering performing maintenance revisions of ANSI N509 and N510 based on the results of a required 5-year review and comments received from users of the standards at workshops and through inquiries. This paper discusses the highlights of the significant revisions to ANSI/ASME N509 and explains the reasons for the changes. It should be emphasized that these revisions are not yet approved by ASME CONAGT, the board of Nuclear Codes and Standards, or ANSI

Analysis of reforming process of large distorted ring in final enlarging forging

International Nuclear Information System (INIS)

Miyazawa, Takeshi; Murai, Etsuo

2002-01-01

In the construction of reactors or pressure vessels for oil chemical plants and nuclear power stations, mono block open-die forging rings are often utilized. Generally, a large forged ring is manufactured by means of enlarging forging with reductions of the wall thickness. During the enlarging process the circular ring is often distorted and becomes an ellipse in shape. However the shape control of the ring is a complicated work. This phenomenon makes the matter still worse in forging of larger rings. In order to make precision forging of large rings, we have developed the forging method using a v-shape anvil. The v-shape anvil is geometrically adjusted to fit the distorted ring in the final circle and reform automatically the shape of the ring during enlarging forging. This paper has analyzed the reforming process of distorted ring by computer program based on F.E.M. and examined the effect on the precision of ring forging. (author)

Equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos

Directory of Open Access Journals (Sweden)

Marta Cristina Rodrigues da Silva

2013-06-01

Full Text Available O objetivo foi analisar e comparar o equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos. Fizeram parte do grupo de estudos 24 sujeitos com idades de 7 a 14 anos divididos em dois grupos: grupo asmático e grupo controle. Para avaliação do equilíbrio corporal utilizou-se uma plataforma de força. Foram utilizadas as condições, olhos abertos e fechados com três tentativas aleatórias, com duração de 30 segundos cada uma. Os resultados apontaram diferença significativa entre os grupos, no teste de equilíbrio com olhos abertos apresentando maior amplitude de deslocamento na direção ântero-posterior (COPap (p = 0,04, e médio lateral (COPml (p = 0,02 no grupo asmático. Enquanto que no teste com olhos fechados a diferença foi significante apenas na amplitude de deslocamento ântero-posterior (COPap (p = 0,02 e Área de Elipse (p=0,03. Desse modo, a asma com suas limitações e consequências parece influenciar negativamente no equilíbrio corporal de seus portadores quando comparados com crianças sem a patologia e da mesma faixa etária.

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

Science.gov (United States)

Luger, T; Van Leent, E J; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knop, J; Knulst, A C; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; Van Der Valk, P G; Bos, J D

2001-04-01

SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy of SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6% and 1.0% in the treatment of patients with atopic dermatitis and to select the concentration to be used in phase III studies. This was a double-blind, randomized, parallel-group, multicentre dose-finding study. A total of 260 patients were randomly assigned to treatment with SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6%, or 1.0%, matching vehicle cream, or the internal control 0.1% betamethasone-17-valerate cream (BMV). Treatment was given twice daily for up to 3 weeks. A clear dose-response relationship for SDZ ASM 981 was evident, with 0.2%, 0.6% and 1.0% SDZ ASM 981 creams all being significantly more effective than vehicle (P = 0.041, 0.001 and 0.008, respectively) in terms of baseline to end-point changes in the Eczema Area Severity Index (EASI) and pruritus score. The 1.0% cream was the most effective SDZ ASM 981 concentration. BMV was more effective than the SDZ ASM 981 creams tested in this study. It appears that the efficacy plateau was not reached with the SDZ ASM 981 creams within 3 weeks treatment. SDZ ASM 981 was well tolerated. Burning or a feeling of warmth were the only adverse events reported more frequently in the 0.6% and 1.0% SDZ ASM 981 treatment groups than in the vehicle treatment group (42.9%, 48.9% and 34.9%, respectively). Few systemic adverse events were reported during the study (headache was the most frequent systemic event reported by 15 of 252 patients) and none was considered to be related to treatment. The local tolerability profile of the 1.0% cream was similar to that of the lower concentrations. 1.0% SDZ ASM 981 cream, which was shown to be safe, well tolerated and

Consideration of the Construction Code for TBM-body in ASME BPVC

International Nuclear Information System (INIS)

Kim, Dongjun; Kim, Yunjae; Kim, Suk Kwon; Park, Sung Dae; Lee, Dong Won

2016-01-01

In this paper, ASME code is briefly introduced, and the TBM-body is classified for selecting the ASME section. With the classification of TBM-body, the appropriate section is determined. Helium Cooled Ceramic Reflector (HCCR) Test Blanket System (TBS) has been designed to research on the functions of breeding blanket by KO TBM team. The functions has three subjects as 1) Tritium breeding, 2) Heat conversion and extraction, and 3) Neutron and Gamma-ray shielding. For the process of design, it is needed to select the appropriate construction code as the design criteria. ITER Organization (IO) has proposed that RCC-MR Edition 2007 ver. shall be used for TBM-shield. Because the TBM-shield is connected to the vacuum boundary. For the other part of TBM-set, TBM-body, there is no constraint on the selected code, and the manufacturer can appropriately select the construction code to apply design and fabrication parts. KO TBM Team has considered whether it is appropriate to choose any code for TBM-body. One of the things is ASME code. The advantage of ASME choice is suitable to the domestic status. In the domestic nuclear plant, ASME or KEPIC code is used as regulatory requirements. Based on this, it is possible to prepare a domestic fusion plant regulatory. In this paper, the construction code of TBM-body was determined in ASME BPVC. For the determination of code, the structure of ASME BPVC was introduced and the classification for TBM-body was conducted by the ITER criteria. And the operation conditions of TBM-body that contained creep and irradiation effects was considered to determine the construction code

Consideration of the Construction Code for TBM-body in ASME BPVC

Energy Technology Data Exchange (ETDEWEB)

Kim, Dongjun; Kim, Yunjae [Korea Univ., Seoul (Korea, Republic of); Kim, Suk Kwon; Park, Sung Dae; Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this paper, ASME code is briefly introduced, and the TBM-body is classified for selecting the ASME section. With the classification of TBM-body, the appropriate section is determined. Helium Cooled Ceramic Reflector (HCCR) Test Blanket System (TBS) has been designed to research on the functions of breeding blanket by KO TBM team. The functions has three subjects as 1) Tritium breeding, 2) Heat conversion and extraction, and 3) Neutron and Gamma-ray shielding. For the process of design, it is needed to select the appropriate construction code as the design criteria. ITER Organization (IO) has proposed that RCC-MR Edition 2007 ver. shall be used for TBM-shield. Because the TBM-shield is connected to the vacuum boundary. For the other part of TBM-set, TBM-body, there is no constraint on the selected code, and the manufacturer can appropriately select the construction code to apply design and fabrication parts. KO TBM Team has considered whether it is appropriate to choose any code for TBM-body. One of the things is ASME code. The advantage of ASME choice is suitable to the domestic status. In the domestic nuclear plant, ASME or KEPIC code is used as regulatory requirements. Based on this, it is possible to prepare a domestic fusion plant regulatory. In this paper, the construction code of TBM-body was determined in ASME BPVC. For the determination of code, the structure of ASME BPVC was introduced and the classification for TBM-body was conducted by the ITER criteria. And the operation conditions of TBM-body that contained creep and irradiation effects was considered to determine the construction code.

ASME nuclear codes and standards: Recent technical initiatives

International Nuclear Information System (INIS)

Feigel, R. E.

1995-01-01

Although nuclear power construction is currently in a hiatus in the US, ASME and its volunteer committees remain committed to continual improvements in the technical requirements in its nuclear codes. This paper provides an overview of several significant recent revisions to ASME' s nuclear codes. Additionally, other important initiatives currently being addressed by ASME committees will be described. With the largest population of operating light water nuclear plants in the world and worldwide use of its nuclear codes, ASME continues to support technical advancements in its nuclear codes and standards. While revisions of various magnitude are an ongoing process, several recent revisions embody significant changes based on state of the art design philosophy and substantial industry experience. In the design area, a significant revisions has recently been approved which will significantly reduce conservatisms in seismic piping design as well as provide simplified design rules. Major revisions have also been made to the requirements for nuclear material manufacturers and suppliers, which should result in clearer understanding of this difficult administrative area of the code. In the area of Section XI inservice rules, substantial studies are underway to investigate the application of probabilistic, risked based inspection in lieu of the current deterministic inspection philosophy. While much work still is required in this area, it is an important potential application of the emerging field of risk based inspection

Medium carbon vanadium steels for closed die forging

International Nuclear Information System (INIS)

Jeszensky, Gabor; Plaut, Ronald Lesley

1993-01-01

This work analyses the medium carbon micro alloyed vanadium potential for closed die forged production. The steels reach the mechanical resistance requests during cooling after forging, eliminating the subsequent thermal treatment. Those steels also present good fatigue resistance and machinability. The industrial scale experiments are also reported

Gear hot forging process robust design based on finite element method

International Nuclear Information System (INIS)

Xuewen, Chen; Won, Jung Dong

2008-01-01

During the hot forging process, the shaping property and forging quality will fluctuate because of die wear, manufacturing tolerance, dimensional variation caused by temperature and the different friction conditions, etc. In order to control this variation in performance and to optimize the process parameters, a robust design method is proposed in this paper, based on the finite element method for the hot forging process. During the robust design process, the Taguchi method is the basic robust theory. The finite element analysis is incorporated in order to simulate the hot forging process. In addition, in order to calculate the objective function value, an orthogonal design method is selected to arrange experiments and collect sample points. The ANOVA method is employed to analyze the relationships of the design parameters and design objectives and to find the best parameters. Finally, a case study for the gear hot forging process is conducted. With the objective to reduce the forging force and its variation, the robust design mathematical model is established. The optimal design parameters obtained from this study indicate that the forging force has been reduced and its variation has been controlled

Optimum design of forging process parameters and preform shape under uncertainties

International Nuclear Information System (INIS)

Repalle, Jalaja; Grandhi, Ramana V.

2004-01-01

Forging is a highly complex non-linear process that is vulnerable to various uncertainties, such as variations in billet geometry, die temperature, material properties, workpiece and forging equipment positional errors and process parameters. A combination of these uncertainties could induce heavy manufacturing losses through premature die failure, final part geometric distortion and production risk. Identifying the sources of uncertainties, quantifying and controlling them will reduce risk in the manufacturing environment, which will minimize the overall cost of production. In this paper, various uncertainties that affect forging tool life and preform design are identified, and their cumulative effect on the forging process is evaluated. Since the forging process simulation is computationally intensive, the response surface approach is used to reduce time by establishing a relationship between the system performance and the critical process design parameters. Variability in system performance due to randomness in the parameters is computed by applying Monte Carlo Simulations (MCS) on generated Response Surface Models (RSM). Finally, a Robust Methodology is developed to optimize forging process parameters and preform shape. The developed method is demonstrated by applying it to an axisymmetric H-cross section disk forging to improve the product quality and robustness

First Results of Energy Saving at Process Redesign of Die Forging Al-Alloys

International Nuclear Information System (INIS)

Pepelnjak, Tomaz; Kuzman, Karl; Kokol, Anton

2011-01-01

The contribution deals with eco-friendly solutions for shortened production chains of forging light alloys. During the die forging operations a remarkable amount of material goes into the flash and later on into chips during finish machining. These low value side products are rich with embedded energy therefore recycling or reprocessing could be very energy saving procedure.In cooperation with a die forging company a shortened reprocessing cycle has been studied starting from re-melting the forging flash and without additional heating to cast preforms for subsequent die forging. As such preforms have not as good formability characteristics as those done from extruded billets the isothermal forging process has been adopted. First results showed that without cracks and other defects the formability is sufficient for a broad spectrum of forgings.To improve the formability a homogenization process of cast preforms has been implemented. As the process started immediately after casting, amount of additional energy for heating was minimized. To reduce voids forging process was redesigned in a way to assure greater hydrostatic pressures in parts during forging. First results were promising therefore research is going towards improving processes without adding significantly more energy as it is needed for casting with homogenization and die forging.

Ultra-large size austenitic stainless steel forgings for fast breeder reactor 'Monju'

International Nuclear Information System (INIS)

Tsukada, Hisashi; Suzuki, Komei; Sato, Ikuo; Miura, Ritsu.

1988-01-01

The large SUS 304 austenitic stainless steel forgings for the reactor vessel of the prototype FBR 'Monju' of 280 MWe output were successfully manufactured. The reactor vessel contains the heart of the reactor and sodium coolant at 530 deg C, and its inside diameter is about 7 m, and height is about 18 m. It is composed of 12 large forgings, that is, very thick flanges and shalls made by ring forging and an end plate made by disk forging and hot forming, using a special press machine. The manufacture of these large forgings utilized the results of the basic test on the material properties in high temperature environment and the effect that the manufacturing factors exert on the material properties and the results of the development of manufacturing techniques for superlarge forgings. The problems were the manufacturing techniques for the large ingots of 250 t class of high purity, the hot working techniques for stainless steel of fine grain size, the forging techniques for superlarge rings and disks, and the machining techniques of high precision for particularly large diameter, thin wall rings. The manufacture of these large stainless steel forgings is reported. (Kako, I.)

77 FR 14445 - Application for a License To Export Steel Forging

Science.gov (United States)

2012-03-09

... NUCLEAR REGULATORY COMMISSION Application for a License To Export Steel Forging Pursuant to 10 CFR 110.70(b) ``Public Notice of Receipt of an Application,'' please take notice that the Nuclear... head steel February 7, 2012 forging. forging will be XR175 machined into the 11005983 finished vessel...

Mannes of Forging and Perspectives of Knuckle Joint Presses Modernization

Directory of Open Access Journals (Sweden)

A. A. Antsifirov

2014-01-01

Full Text Available The article raises an issue to enhance technological forging capabilities on the known knuckle joint presses. It provides an illustrated overview of main design types of presses with crank-knuckle, toggle-knuckle, and knuckle joint mechanisms. The article also shows the advantages of the modernization way and improvement just of the active press equipment in terms of quality-to-price ratio, for example, as compared to the similar new foreign press equipment.It gives an overview of features, which provide forging processes owing to kinetic energy accumulated with the moving parts of the known designs of the knuckle joint presses depending on the drive actuating mechanism. Focused attention is drawn to forging on the knuckle joint presses for a time of contact with a work piece to be comparable with the duration of the work piece deformation process on hydraulic forging hammers. This allows us to forge thin-wall products with process automation compared to the forging hammers.Analysis of accumulating processes of kinetic energy by the moving parts of the knuckle joint presses has shown that presses driven by hydraulic cylinders or two screw hydraulic cylinder are the most optimal for technological operations as evidenced by references to domestic and foreign invention certificates and patents. The article presents disadvantages of forging on presses with hydraulic or pneumatic drive. It is a dependence of the deformation force, caused, mainly, by a force of the drive cylinder. The article gives linear movement rate quantities of press moving members depending on the drives of the actuating mechanism. Based on the above analysis of the features to manufacture work pieces on the knuckle joint presses, the article gives the rationale for the relevance of forging in a short period of time, provided that the moving parts of the press accumulate the required kinetic energy. This can be achieved only through modernization and improvement of forging

Optical Forging of Graphene into Three-Dimensional Shapes.

Science.gov (United States)

Johansson, Andreas; Myllyperkiö, Pasi; Koskinen, Pekka; Aumanen, Jukka; Koivistoinen, Juha; Tsai, Hung-Chieh; Chen, Chia-Hao; Chang, Lo-Yueh; Hiltunen, Vesa-Matti; Manninen, Jyrki J; Woon, Wei Yen; Pettersson, Mika

2017-10-11

Atomically thin materials, such as graphene, are the ultimate building blocks for nanoscale devices. But although their synthesis and handling today are routine, all efforts thus far have been restricted to flat natural geometries, since the means to control their three-dimensional (3D) morphology has remained elusive. Here we show that, just as a blacksmith uses a hammer to forge a metal sheet into 3D shapes, a pulsed laser beam can forge a graphene sheet into controlled 3D shapes in the nanoscale. The forging mechanism is based on laser-induced local expansion of graphene, as confirmed by computer simulations using thin sheet elasticity theory.

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2012-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2011-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

Analysis of the Current Technical Issues on ASME Code and Standard for Nuclear Mechanical Design(2009)

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2009-11-01

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

Analysis of the Current Technical Issues on ASME Code and Standard for Nuclear Mechanical Design(2009)

Energy Technology Data Exchange (ETDEWEB)

Koo, Gyeong Hoi; Lee, B. S.; Yoo, S. H.

2009-11-15

This report describes the analysis on the current revision movement related to the mechanical design issues of the U.S ASME nuclear code and standard. ASME nuclear mechanical design in this report is composed of the nuclear material, primary system, secondary system and high temperature reactor. This report includes the countermeasures based on the ASME Code meeting for current issues of each major field. KAMC(ASME Mirror Committee) of this project is willing to reflect a standpoint of the domestic nuclear industry on ASME nuclear mechanical design and play a technical bridge role for the domestic nuclear industry in ASME Codes application

GC-ASM: Synergistic Integration of Graph-Cut and Active Shape Model Strategies for Medical Image Segmentation.

Science.gov (United States)

Chen, Xinjian; Udupa, Jayaram K; Alavi, Abass; Torigian, Drew A

2013-05-01

Image segmentation methods may be classified into two categories: purely image based and model based. Each of these two classes has its own advantages and disadvantages. In this paper, we propose a novel synergistic combination of the image based graph-cut (GC) method with the model based ASM method to arrive at the GC-ASM method for medical image segmentation. A multi-object GC cost function is proposed which effectively integrates the ASM shape information into the GC framework. The proposed method consists of two phases: model building and segmentation. In the model building phase, the ASM model is built and the parameters of the GC are estimated. The segmentation phase consists of two main steps: initialization (recognition) and delineation. For initialization, an automatic method is proposed which estimates the pose (translation, orientation, and scale) of the model, and obtains a rough segmentation result which also provides the shape information for the GC method. For delineation, an iterative GC-ASM algorithm is proposed which performs finer delineation based on the initialization results. The proposed methods are implemented to operate on 2D images and evaluated on clinical chest CT, abdominal CT, and foot MRI data sets. The results show the following: (a) An overall delineation accuracy of TPVF > 96%, FPVF ASM for different objects, modalities, and body regions. (b) GC-ASM improves over ASM in its accuracy and precision to search region. (c) GC-ASM requires far fewer landmarks (about 1/3 of ASM) than ASM. (d) GC-ASM achieves full automation in the segmentation step compared to GC which requires seed specification and improves on the accuracy of GC. (e) One disadvantage of GC-ASM is its increased computational expense owing to the iterative nature of the algorithm.

Evaluation of intergranular cracks on the ring header cross at Grand Gulf Unit No. 1

International Nuclear Information System (INIS)

Czajkowski, C.J.

1987-01-01

A metallurgical investigation was performed on a sample of cracked ring header cross material from the Grand Gulf Unit No. 1 Nuclear Power Station. The cracks were located in a 6-7 in (15-17.5 cm) width band running circumferentially below the cross to cap weld with a similar band above the cross to discharger pipe weld. The indications were up to 19 mm in length and 6.0 mm in depth. This particular sample was cut from a cross which had not seen actual service but which had been used to qualify the induction heating stress improvement (IHSI) technique for the Grand Gulf units. The base material was SA 182 material manufactured to SA 403-type WP 304 stainless steel. The investigation consisted of visual/dye penetrant examination, chemical analysis, hardness testing, optical microscopy, scanning electron microscopy and energy dispersive spectroscopy. The evaluated cracks were intergranular and initiated on the forging's exterior surface. The grain size of the material was larger than ASTM 00 and no definitive corrosive species were found by Energy Dispersive Spectroscopy (EDS). The cracking is considered to be the result of the forging having been overheated/burned during manufacture. (author)

Development of high purity large forgings for nuclear power plants

International Nuclear Information System (INIS)

Tanaka, Yasuhiko; Sato, Ikuo

2011-01-01

The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

Development of high purity large forgings for nuclear power plants

Science.gov (United States)

Tanaka, Yasuhiko; Sato, Ikuo

2011-10-01

The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

Operating nuclear plant feedback to ASME and French codes

International Nuclear Information System (INIS)

Journet, J.; O'Donnell, W.J.

1996-01-01

The French have an advantage in nuclear plant operating experience feedback due to the highly centralized nature of their nuclear industry. There is only one utility in charge of design as well as operations (EDF) and only one reactor vendor (Framatome). The ASME Code has played a key role in resolving technical issues in the design and operation of nuclear plants since the inception of nuclear power. The committee structure of the Code brings an ideal combination of senior technical people with both broad and specialized experience to bear on complex how safe is safe enough technical issues. The authors now see an even greater role for the ASME Code in a proposed new regulatory era for the US nuclear industry. The current legalistic confrontational regulatory era has been quite destructive. There now appears to be a real opportunity to begin a new era of technical consensus as the primary means for resolving safety issues. This change can quickly be brought about by having the industry take operating plant problems and regulatory technical issues directly to the ASME Code for timely resolution. Surprisingly, there is no institution in the US nuclear industry with such a mandate. In fact, the industry is organized to feedback through the Nuclear Regulatory Commission issues which could be far better resolved through the ASME Code. Major regulatory benefits can be achieved by closing this loop and providing systematic interaction with the ASME Code. The essential elements of a new regulatory era and ideas for organizing US institutional industry responsibilities, taken from the French experience, are described in this paper

ASME method for particle reconstruction

International Nuclear Information System (INIS)

Ierusalimov, A.P.

2009-01-01

The method of approximate solution of motion equation (ASME) was used to reconstruct the parameters for charged particles. It provides a good precision for momentum, angular and space parameters of particles in coordinate detectors. The application of the method for CBM, HADES and MPD/NICA setups is discussed

Development of Oxide Dispersion Strengthened (ODS) Ferritic Steel Through Powder Forging

Science.gov (United States)

Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

2017-04-01

Oxide dispersion strengthened (ODS) ferritic steels are candidates for cladding tubes in fast breeder nuclear reactors. In this study, an 18%Cr ODS ferritic steel was prepared through powder forging route. Elemental powders with a nominal composition of Fe-18Cr-2 W-0.2Ti (composition in wt.%) with 0 and 0.35% yttria were prepared by mechanical alloying in a Simoloyer attritor under argon atmosphere. The alloyed powders were heated in a mild steel can to 1473 K under flowing hydrogen atmosphere. The can was then hot forged. Steps of sealing, degassing and evacuation are eliminated by using powder forging. Heating ODS powder in hydrogen atmosphere ensures good bonding between alloy powders. A dense ODS alloy with an attractive combination of strength and ductility was obtained after re-forging. On testing at 973 K, a loss in ductility was observed in yttria-containing alloy. The strength and ductility increased with increase in strain rate at 973 K. Reasons for this are discussed. The ODS alloy exhibited a recrystallized microstructure which is difficult to achieve by extrusion. No prior particle boundaries were observed after forging. The forged compacts exhibited isotropic mechanical properties. It is suggested that powder forging may offer several advantages over the traditional extrusion/HIP routes for fabrication of ODS alloys.

Regulatory Endorsement Activities for ASME Nuclear Codes and Standards

International Nuclear Information System (INIS)

West, Raymond A.

2006-01-01

The ASME Board on Nuclear Codes and Standards (BNCS) has formed a Task Group on Regulatory Endorsement (TG-RE) that is currently in discussions with the United States Nuclear Regulatory Commission (NRC) to look at suggestions and recommendations that can be used to help with the endorsement of new and revised ASME Nuclear Codes and Standards (NC and S). With the coming of new reactors in the USA in the very near future we need to look at both the regulations and all the ASME NC and S to determine where we need to make changes to support these new plants. At the same time it is important that we maintain our operating plants while addressing ageing management needs of our existing reactors. This is going to take new thinking, time, resources, and money. For all this to take place the regulations and requirements that we use must be clear concise and necessary for safety and to that end both the NRC and ASME are working together to make this happen. Because of the influence that the USA has in the world in dealing with these issues, this paper is written to inform the international nuclear engineering community about the issues and what actions are being addressed under this effort. (author)

Medium carbon vanadium micro alloyed steels for drop forging

International Nuclear Information System (INIS)

Jeszensky, Gabor; Plaut, Ronald Lesley

1992-01-01

Growing competitiveness of alternative manufacturing routes requires cost minimization in the production of drop forged components. The authors analyse the potential of medium carbon, vanadium microalloyed steels for drop forging. Laboratory and industrial experiments have been carried out emphasizing deformation and temperature cycles, strain rates and dwell times showing a typical processing path, associated mechanical properties and corresponding microstructures. The steels the required levels of mechanical properties on cooling after forging, eliminating subsequent heat treatment. The machinability of V-microalloyed steels is also improved when compared with plain medium carbon steels. (author)

21 CFR 182.3890 - Tocopherols.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tocopherols. 182.3890 Section 182.3890 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives § 182.3890 Tocopherols. (a) Product. Tocopherols. (b) Conditions of use. This substance is generally recognized as safe when...

Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

International Nuclear Information System (INIS)

Kwon, Yong Chul; Kang, Jong Hun; Kim, Sang Sik

2016-01-01

The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts

Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

Energy Technology Data Exchange (ETDEWEB)

Kwon, Yong Chul [Gyeongnam Technopark, Changwon (Korea, Republic of); Kang, Jong Hun [Jungwon Univ., Goisan (Korea, Republic of); Kim, Sang Sik [Gyeongsang Natiional Univ., Jinju (Korea, Republic of)

2016-02-15

The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts.

2 CFR 182.640 - Employee.

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Employee. 182.640 Section 182.640 Grants and... GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Definitions § 182.640 Employee. (a) Employee means the employee of a recipient directly engaged in the performance of work under the award...

21 CFR 182.8890 - Tocopherols.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tocopherols. 182.8890 Section 182.8890 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Nutrients § 182.8890 Tocopherols. (a) Product. Tocopherols. (b) Conditions of use. This substance is generally recognized as safe when used in accordance...

28 CFR 18.2 - Application.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Application. 18.2 Section 18.2 Judicial Administration DEPARTMENT OF JUSTICE OFFICE OF JUSTICE PROGRAMS HEARING AND APPEAL PROCEDURES § 18.2 Application. (a) These procedures apply to all appeals and hearings of State formula or block grant applicants or...

21 CFR 182.8159 - Biotin.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Biotin. 182.8159 Section 182.8159 Food and Drugs... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Nutrients § 182.8159 Biotin. (a) Product. Biotin. (b) Conditions of use. This substance is generally recognized as safe when used in accordance...

29 CFR 18.2 - Definitions.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Definitions. 18.2 Section 18.2 Labor Office of the Secretary of Labor RULES OF PRACTICE AND PROCEDURE FOR ADMINISTRATIVE HEARINGS BEFORE THE OFFICE OF ADMINISTRATIVE LAW JUDGES General § 18.2 Definitions. For purposes of these rules: (a) Adjudicatory proceeding...

Integrin and GPCR Crosstalk in the Regulation of ASM Contraction Signaling in Asthma.

Science.gov (United States)

Teoh, Chun Ming; Tam, John Kit Chung; Tran, Thai

2012-01-01

Airway hyperresponsiveness (AHR) is one of the cardinal features of asthma. Contraction of airway smooth muscle (ASM) cells that line the airway wall is thought to influence aspects of AHR, resulting in excessive narrowing or occlusion of the airway. ASM contraction is primarily controlled by agonists that bind G protein-coupled receptor (GPCR), which are expressed on ASM. Integrins also play a role in regulating ASM contraction signaling. As therapies for asthma are based on symptom relief, better understanding of the crosstalk between GPCRs and integrins holds good promise for the design of more effective therapies that target the underlying cellular and molecular mechanism that governs AHR. In this paper, we will review current knowledge about integrins and GPCRs in their regulation of ASM contraction signaling and discuss the emerging concept of crosstalk between the two and the implication of this crosstalk on the development of agents that target AHR.

Lubricant influence on the ejection and roughness of in-die electro sinter forged Ti-discs

DEFF Research Database (Denmark)

Cannella, Emanuele; Nielsen, Chris Valentin

2018-01-01

Electro Sinter Forging (ESF) is a new sintering process based on Joule heating by high electrical current flowing through compacted metal powder under mechanical pressure. The whole process takes about three seconds and is based on a closed-die setup, where the sample is sintered inside a die....... A near-net shape component is therefore manufactured. One of the challenges associated with this process is the ejection of the sample after sintering. Due to powder compaction and axial loading during sintering, a radial pressure is generated at the die/sample interface. Consequently, the ejection can...... of commercially pure titanium powder. The force was measured while ejecting the samples by using a speed-controlled press. The surface roughness parameter Sa was measured by using a laser confocal microscope....

2 CFR 182.665 - State.

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false State. 182.665 Section 182.665 Grants and... GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Definitions § 182.665 State. State means any of the States of the United States, the District of Columbia, the Commonwealth of Puerto Rico...

12 CFR 18.2 - Definitions.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Definitions. 18.2 Section 18.2 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY DISCLOSURE OF FINANCIAL AND OTHER INFORMATION BY NATIONAL BANKS § 18.2 Definitions. Unless otherwise defined in this part, the terms used have...

Risk-informed technology developments for nuclear power plants within the ASME in 2000-2001

International Nuclear Information System (INIS)

Wesley Rowley, C.; Balkey, K.R.

2001-01-01

The purpose of this paper is to provide information on developments within the ASME to support risk-informing NRC regulations for nuclear power plants. This paper builds on a publication at ICONE-8 that discussed ASME risk-informed nuclear power plant initiatives, both in Research and in Codes and Standards, particularly those related to risk-informing Part 50 of the 10 CFR (Code of federal regulations). During the past year, the ASME BNCS formed a Task Force to focus the Society's efforts to support risk-informing 10 CFR Part 50. Key efforts underway that are guided by the task force include finalizing the ASME PRA (probability risk assessment) Standard, developing a Code Case to risk-inform the repair, replacement, and modification activities for ASME components, and developing a Code Case to risk-inform the safety classification of pressure boundary components. Several other initiatives are also under investigation such as introducing risk insights into other ASME nuclear codes and standards supported by appropriate research and technical basis information. Supplementary information will also be provided to update an initial high level plan of ASME risk-informed initiatives for nuclear power plants that was presented at ICONE-8, including plans to communicate these risk-informed technology developments to the public. The authors included and acknowledged contributions from several other cognizant members of the ASME BNCS (board on nuclear codes standards) Task Group on RIP50 in the paper. (authors)

Optimising mechanical properties of hot forged nickel superalloy 625 components

Science.gov (United States)

Singo, Nthambe; Coles, John; Rosochowska, Malgorzata; Lalvani, Himanshu; Hernandez, Jose; Ion, William

2018-05-01

Hot forging and subsequent heat treatment were resulting in substandard mechanical properties of nickel superalloy, Alloy 625, components. The low strength was found to be due to inadequate deformation during forging, excessive grain growth and precipitation of carbides during subsequent heat treatment. Experimentation in a drop forging company and heat treatment facility led to the establishment of optimal parameters to minimise grain size and mitigate the adverse effects of carbide precipitation, leading to successful fulfilment of mechanical property specifications. This was achieved by reducing the number of operations, maximising the extent of deformation by changing the slug dimensions and its orientation in the die, and minimising the time of exposure to elevated temperatures in both the forging and subsequent heat treatment processes to avoid grain growth.

Inhibition of allergen-induced basophil activation by ASM-024, a nicotinic receptor ligand.

Science.gov (United States)

Watson, Brittany M; Oliveria, John Paul; Nusca, Graeme M; Smith, Steven G; Beaudin, Sue; Dua, Benny; Watson, Rick M; Assayag, Evelynne Israël; Cormier, Yvon F; Sehmi, Roma; Gauvreau, Gail M

2014-01-01

Nicotinic acetylcholine receptors (nAChRs) were identified on eosinophils and shown to regulate inflammatory responses, but nAChR expression on basophils has not been explored yet. We investigated surface receptor expression of nAChR α4, α7 and α1/α3/α5 subunits on basophils. Furthermore, we examined the effects of ASM-024, a synthetic nicotinic ligand, on in vitro anti-IgE and in vivo allergen-induced basophil activation. Basophils were enriched from the peripheral blood of allergic donors and the expression of nAChR subunits and muscarinic receptors was determined. Purified basophils were stimulated with anti-IgE in the presence of ASM-024 with or without muscarinic or nicotinic antagonists for the measurement of CD203c expression and histamine release. The effect of 9 days of treatment with 50 and 200 mg ASM-024 on basophil CD203c expression was examined in the blood of mild allergic asthmatics before and after allergen inhalation challenge. nAChR α4, α7 and α1/α3/α5 receptor subunit expression was detected on basophils. Stimulation of basophils with anti-IgE increased CD203c expression and histamine release, which was inhibited by ASM-024 (10(-5) to 10(-)(3) M, p ASM-024 was reversed in the presence of muscarinic and nicotinic antagonists. In subjects with mild asthma, ASM-024 inhalation significantly inhibited basophil CD203c expression measured 24 h after allergen challenge (p = 0.03). This study shows that ASM-024 inhibits IgE- and allergen-induced basophil activation through both nicotinic and muscarinic receptors, and suggests that ASM-024 may be an efficacious agent for modulating allergic asthma responses. © 2015 S. Karger AG, Basel.

Acid Sphingomyelinase (ASM) is a Negative Regulator of Regulatory T Cell (Treg) Development.

Science.gov (United States)

Zhou, Yuetao; Salker, Madhuri S; Walker, Britta; Münzer, Patrick; Borst, Oliver; Gawaz, Meinrad; Gulbins, Erich; Singh, Yogesh; Lang, Florian

2016-01-01

Regulatory T cell (Treg) is required for the maintenance of tolerance to various tissue antigens and to protect the host from autoimmune disorders. However, Treg may, indirectly, support cancer progression and bacterial infections. Therefore, a balance of Treg function is pivotal for adequate immune responses. Acid sphingomyelinase (ASM) is a rate limiting enzyme involved in the production of ceramide by breaking down sphingomyelin. Previous studies in T-cells have suggested that ASM is involved in CD28 signalling, T lymphocyte granule secretion, degranulation, and vesicle shedding similar to the formation of phosphatidylserine-exposing microparticles from glial cells. However, whether ASM affects the development of Treg has not yet been described. Splenocytes, isolated Naive T lymphocytes and cultured T cells were characterized for various immune T cell markers by flow cytometery. Cell proliferation was measured by Carboxyfluorescein succinimidyl ester (CFSE) dye, cell cycle analysis by Propidium Iodide (PI), mRNA transcripts by q-RT PCR and protein expression by Western Blotting respectively. ASM deficient mice have higher number of Treg compared with littermate control mice. In vitro induction of ASM deficient T cells in the presence of TGF-β and IL-2 lead to a significantly higher number of Foxp3+ induced Treg (iTreg) compared with control T-cells. Further, ASM deficient iTreg has less AKT (serine 473) phosphorylation and Rictor levels compared with control iTreg. Ceramide C6 led to significant reduction of iTreg in both ASM deficient and WT mice. The reduction in iTreg leads to induction of IL-1β, IL-6 and IL-17 but not IFN-γ mRNA levels. ASM is a negative regulator of natural and iTreg. © 2016 The Author(s) Published by S. Karger AG, Basel.

Using of material-technological modelling for designing production of closed die forgings

Science.gov (United States)

Ibrahim, K.; Vorel, I.; Jeníček, Š.; Káňa, J.; Aišman, D.; Kotěšovec, V.

2017-02-01

Production of forgings is a complex and demanding process which consists of a number of forging operations and, in many cases, includes post-forge heat treatment. An optimized manufacturing line is a prerequisite for obtaining prime-quality products which in turn are essential to profitable operation of a forging company. Problems may, however, arise from modifications to the manufacturing route due to changing customer needs. As a result, the production may have to be suspended temporarily to enable changeover and optimization. Using material-technological modelling, the required modifications can be tested and optimized under laboratory conditions outside the plant without disrupting the production. Thanks to material-technological modelling, the process parameters can be varied rapidly in response to changes in market requirements. Outcomes of the modelling runs include optimum parameters for the forging part’s manufacturing route, values of mechanical properties, and results of microstructure analysis. This article describes the use of material-technological modelling for exploring the impact of the amount of deformation and the rate of cooling of a particular forged part from the finish-forging temperature on its microstructure and related mechanical properties.

Study on isothermal precision forging process of rare earth intensifying magnesium alloy

International Nuclear Information System (INIS)

Shan, Debin; Xu, Wenchen; Han, Xiuzhu; Huang, Xiaolei

2012-01-01

A three dimensional rigid-plastic finite element model is established to simulate the isothermal precision forging process of the magnesium alloy bracket based on DEFORM 3D in order to analyze the material flow rule and determine the forging process scheme. Some problems such as underfilling and too large forging pressure are predicted and resolved through optimizing the shapes of the billet successfully. Compared to the initial microstructure, the isothermal-forged microstructure of the alloy refines obviously and amounts of secondary phases precipitate on the matrix during isothermal forging process. In subsequent ageing process, large quantities of secondary phases precipitate from α-Mg matrix with increasing ageing time. The optimal comprehensive mechanical properties of the alloy have been obtained after aged at 473 K, 63 h with the ultimate tensile strength, tensile yield strength and elongation 380 MPa, 243 MPa and 4.07% respectively, which shows good potential for application of isothermal forging process of rare earth intensifying magnesium alloy.

Near net shape forging of titanium alloy turbine blade

International Nuclear Information System (INIS)

Morita, Akiyasu; Hattori, Shigeo; Tani, Kazuhito; Takemura, Atsushi; Ashida, Yoshio

1991-01-01

The isothermal forging process has been developed to produce turbine blades made of near β Ti-alloy Ti-10V-2Fe-3Al. It is important to set the preform at the optimum position of the die in order to get a high precision product. The deformation analysis by using FEM is effective to determine the optimum position. And also it is necessary to avoid buckling induced by the restriction of axial elongation of the material. As a result, Ti-10V-2Fe-3Al blades could be formed precisely by using only one stage of forging, and machining was needed only at the root. The thickness of the oxide layer induced on the surface of the forged blade was only 70μm. The mechanical properties of Ti-10V-2Fe-3Al blades after forging and annealing were superior to those of Ti-6Al-4V blades and were nearly uniform across the length of the blades. (author)

Sensitivity analysis and optimization algorithms for 3D forging process design

International Nuclear Information System (INIS)

Do, T.T.; Fourment, L.; Laroussi, M.

2004-01-01

This paper presents several approaches for preform shape optimization in 3D forging. The process simulation is carried out using the FORGE3 registered finite element software, and the optimization problem regards the shape of initial axisymmetrical preforms. Several objective functions are considered, like the forging energy, the forging force or a surface defect criterion. Both deterministic and stochastic optimization algorithms are tested for 3D applications. The deterministic approach uses the sensitivity analysis that provides the gradient of the objective function. It is obtained by the adjoint-state method and semi-analytical differentiation. The study of stochastic approaches aims at comparing genetic algorithms and evolution strategies. Numerical results show the feasibility of such approaches, i.e. the achieving of satisfactory solutions within a limited number of 3D simulations, less than fifty. For a more industrial problem, the forging of a gear, encouraging optimization results are obtained

High yttria ferritic ODS steels through powder forging

Energy Technology Data Exchange (ETDEWEB)

Kumar, Deepak [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Prakash, Ujjwal, E-mail: ujwalfmt@iitr.ac.in [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Dabhade, Vikram V. [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Laha, K.; Sakthivel, T. [Mechanical Metallurgy Group, IGCAR, Kalpakkam, Tamilnadu 603102 (India)

2017-05-15

Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y{sub 2}O{sub 3} (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility. - Highlights: •ODS steels with yttria contents beyond the conventional limit of 0.5 wt% were fabricated by powder forging in a hydrogen atmosphere. •All the alloys exhibited significant ductility. •This may be attributed to improved inter-particle bonding due to reduction of surface oxides by hydrogen. •Strength in excess of 300 MPa was obtained at 973 K for 0.5%, 1% and 1.5% yttria ODS alloys. •Powder forging is a promising route to fabricate ODS steels and permits development of compositions with up to 1.5% yttria.

ASM-024, a piperazinium compound, promotes the in vitro relaxation of β2-adrenoreceptor desensitized tracheas.

Science.gov (United States)

Israël-Assayag, Evelyne; Beaulieu, Marie-Josée; Cormier, Yvon

2015-01-01

Inhaled β2-adrenoreceptor agonists are widely used in asthma and chronic obstructive pulmonary disease (COPD) for bronchoconstriction relief. β2-Adrenoreceptor agonists relax airway smooth muscle cells via cyclic adenosine monophosphate (cAMP) mediated pathways. However, prolonged stimulation induces functional desensitization of the β2-adrenoreceptors (β2-AR), potentially leading to reduced clinical efficacy with chronic or prolonged administration. ASM-024, a small synthetic molecule in clinical stage development, has shown activity at the level of nicotinic receptors and possibly at the muscarinic level and presents anti-inflammatory and bronchodilator properties. Aerosolized ASM-024 reduces airway resistance in mice and promotes in-vitro relaxation of tracheal and bronchial preparations from animal and human tissues. ASM-024 increased in vitro relaxation response to maximally effective concentration of short-acting beta-2 agonists in dog and human bronchi. Although the precise mechanisms by which ASM-024 promotes airway smooth muscle (ASM) relaxation remain unclear, we hypothesized that ASM-024 will attenuate and/or abrogate agonist-induced contraction and remain effective despite β2-AR tachyphylaxis. β2-AR tachyphylaxis was induced with salbutamol, salmeterol and formoterol on guinea pig tracheas. The addition of ASM-024 relaxed concentration-dependently intact or β2-AR desensitized tracheal rings precontracted with methacholine. ASM-024 did not induce any elevation of intracellular cAMP in isolated smooth muscle cells; moreover, blockade of the cAMP pathway with an adenylate cyclase inhibitor had no significant effect on ASM-024-induced guinea pig trachea relaxation. Collectively, these findings show that ASM-024 elicits relaxation of β2-AR desensitized tracheal preparations and suggest that ASM-024 mediates smooth muscle relaxation through a different target and signaling pathway than β2-adrenergic receptor agonists. These findings suggest ASM-024

Close toleranoe forging of chromium steel blades for powerful steam turbines

International Nuclear Information System (INIS)

Shastin, Eh.G.; Kositskij, Yu.N.; Lyubchits, G.A.

1989-01-01

Work on simulating technological process on die-forging hammer was performed in order to reduce the preparation period bringing technology of close tolerance forging of turbine blades to a commercial level. A special attention was paid to development of accurate forming of forgings of 20Kh13Sh, 12Kh13 and 15Kh11MFSh steels on screw presses with nominal effort equal to 80 and 144 MN

Analysis of preservice inspection relief requests and recommendations for ASME code changes

International Nuclear Information System (INIS)

Cook, J.F.

1985-05-01

NRC regulations require that preservice inspection (PSI) of nuclear plants be performed in accordance with referenced editions and addenda of Division 1 rules of Section XI, ''Rules for Inservice Inspection of Nuclear Power Plant Components'', of the ASME Boiler and Pressure Vessel Code (ASME Code). The regulations permit applicants to request and obtain relief from the NRC from specific ASME Code requirements that are determined to be impractical. Applicant requests for relief from preservice inspection (PSI) requirements were compiled and analyzed. From this data, covering a total of 178 relief requests, common problems with examination requirements were identified. Changes to examination requirements to solve selected problems are proposed. By following later ASME Code requirements, 46 out of the 178 relief requests can be eliminated. Implementing proposed Code changes would eliminate another 25 relief requests, leaving 107 relief requests out of the original 178 relief requests covered by this survey

J-R Fracture Resistance of SA533 Gr.B-Cl.1 Steel for Reactor Pressure Vessel

Energy Technology Data Exchange (ETDEWEB)

Yoon, Ji-Hyun; Hong, Seokmin; Lee, Bong-Sang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

A rolled plate might show different mechanical behaviors from a forging, even though they contain same chemical compositions. Furthermore, it is known that the fracture behavior of a rolled plate is very sensitive to material orientation comparing to a forging. In this study, the J-R fracture resistances of SA533 Gr.B-Cl.1 plate were measured at reactor operating temperature and the material orientation sensitivity was discussed. The decrease of fracture resistance of this kind of low alloy steel at an elevated temperature is known as the effect of dynamic strain aging (DSA). It was attributed to that the carbides and grains elongated to primary rolling direction, so that the aspect ratio of carbides and grains in the specimen with T-L orientation is larger. Generally, the hard second phase could take a roll of trigger point of unstable fracture. It is needed that the fracture surfaces of the tested specimens to be examined profoundly.

Evaluation of practicality of ASME code, Section XI

International Nuclear Information System (INIS)

Mattu, R.K.; Lauderdale, J.R.; Liu, S.N.; Lance, J.J.

2004-01-01

Many nuclear power plants have found that it is impractical or unduly burdensome to comply with some ASME Boiler and Pressure Code provisions and have sought relief from those provisions from the Nuclear Regulatory Commission. An Electric Power Research Institute (EPRI) project is evaluating such Code provisions and alternatives to them that will meet the safety intent of the Code with less burden on utilities. The methodology is to extract data from an on-line data base of relief requests since 1980, analyse the data to identify burdensome provisions for which there are satisfactory alternatives, and recommend changes in the Code to the ASME. (author)

NIST/ASME Steam Properties Database

Science.gov (United States)

SRD 10 NIST/ASME Steam Properties Database (PC database for purchase)   Based upon the International Association for the Properties of Water and Steam (IAPWS) 1995 formulation for the thermodynamic properties of water and the most recent IAPWS formulations for transport and other properties, this updated version provides water properties over a wide range of conditions according to the accepted international standards.

High Level Analysis, Design and Validation of Distributed Mobile Systems with CoreASM

Science.gov (United States)

Farahbod, R.; Glässer, U.; Jackson, P. J.; Vajihollahi, M.

System design is a creative activity calling for abstract models that facilitate reasoning about the key system attributes (desired requirements and resulting properties) so as to ensure these attributes are properly established prior to actually building a system. We explore here the practical side of using the abstract state machine (ASM) formalism in combination with the CoreASM open source tool environment for high-level design and experimental validation of complex distributed systems. Emphasizing the early phases of the design process, a guiding principle is to support freedom of experimentation by minimizing the need for encoding. CoreASM has been developed and tested building on a broad scope of applications, spanning computational criminology, maritime surveillance and situation analysis. We critically reexamine here the CoreASM project in light of three different application scenarios.

Estimates of margins in ASME Code strength values for stainless steel nuclear piping

International Nuclear Information System (INIS)

Ware, A.G.

1995-01-01

The margins in the ASME Code stainless steel allowable stress values that can be attributed to the variations in material strength are evaluated for nuclear piping steels. Best-fit curves were calculated for the material test data that were used to determine allowable stress values for stainless steels in the ASME Code, supplemented by more recent data, to estimate the mean stresses. The mean yield stresses (on which the stainless steel S m values are based) from the test data are about 15 to 20% greater than the ASME Code yield stress values. The ASME Code yield stress values are estimated to approximately coincide with the 97% confidence limit from the test data. The mean and 97% confidence limit values can be used in the probabilistic risk assessments of nuclear piping

Integral forged pump casing for the primary coolant circuit of a nuclear reactor: Development in design, forging technology, and material

International Nuclear Information System (INIS)

Austel, W.; Korbe, H.

1986-01-01

Developments in the forging of large casings for primary circuit coolant pumps for light water reactors in Germany are demonstrated beginning with the multiple forging fabricated version and ending with the integral forged type. This version is the result of the joint efforts of the pump manufacturer and the forgemaster after a cost-gain evaluation and represents an optimum solution in view of its functional and economical performance and also considering the high requirements for mechanical-technological properties, including homogeneity of the material. The development from 22 NiMoCr 3 7/A 508 Class 2 to 20 MnMoNi 5 5/A 508 Class 3 and their optimization will be demonstrated. This development is based mainly on minimizing the sulfur content and on vacuum carbon deoxidation (VCD), which results in a reduction of the A-segregations, in improving fracture toughness and isotropy, and in the desired fine-grain structure

A comparative study for SMART steam generator sizing based on ASME and Russian standard

International Nuclear Information System (INIS)

Kim, Y. W.; Kim, J. I.; Jang, M. H.

2000-01-01

A systematic comparison of ASME and Russian standard with respect to the design of SMART steam generator has been carried out. Classification of allowable stress in the Russian standard is quite different from that of ASME. Allowable stress of Russian standard and stress intensity defined in ASME were compared for various steam generator tube material as a function of design temperature. Equations and methodology of determining the thickness for the important parts of steam generator have been analyzed. For the tube subjected to internal and/or external pressure, Russian standard use the same equation in the sizing of tube with different allowable stress. However, ASME use different equations with the same value of allowable stress intensity. The hydraulic test pressure of ASME was also compared with that of Russian standard. In general, hydraulic test pressure determined by Russian standard is higher since it considers difference between allowable stress of test temperature and that of design temperature

A minimal path searching approach for active shape model (ASM)-based segmentation of the lung

Science.gov (United States)

Guo, Shengwen; Fei, Baowei

2009-02-01

We are developing a minimal path searching method for active shape model (ASM)-based segmentation for detection of lung boundaries on digital radiographs. With the conventional ASM method, the position and shape parameters of the model points are iteratively refined and the target points are updated by the least Mahalanobis distance criterion. We propose an improved searching strategy that extends the searching points in a fan-shape region instead of along the normal direction. A minimal path (MP) deformable model is applied to drive the searching procedure. A statistical shape prior model is incorporated into the segmentation. In order to keep the smoothness of the shape, a smooth constraint is employed to the deformable model. To quantitatively assess the ASM-MP segmentation, we compare the automatic segmentation with manual segmentation for 72 lung digitized radiographs. The distance error between the ASM-MP and manual segmentation is 1.75 +/- 0.33 pixels, while the error is 1.99 +/- 0.45 pixels for the ASM. Our results demonstrate that our ASM-MP method can accurately segment the lung on digital radiographs.

A Minimal Path Searching Approach for Active Shape Model (ASM)-based Segmentation of the Lung.

Science.gov (United States)

Guo, Shengwen; Fei, Baowei

2009-03-27

We are developing a minimal path searching method for active shape model (ASM)-based segmentation for detection of lung boundaries on digital radiographs. With the conventional ASM method, the position and shape parameters of the model points are iteratively refined and the target points are updated by the least Mahalanobis distance criterion. We propose an improved searching strategy that extends the searching points in a fan-shape region instead of along the normal direction. A minimal path (MP) deformable model is applied to drive the searching procedure. A statistical shape prior model is incorporated into the segmentation. In order to keep the smoothness of the shape, a smooth constraint is employed to the deformable model. To quantitatively assess the ASM-MP segmentation, we compare the automatic segmentation with manual segmentation for 72 lung digitized radiographs. The distance error between the ASM-MP and manual segmentation is 1.75 ± 0.33 pixels, while the error is 1.99 ± 0.45 pixels for the ASM. Our results demonstrate that our ASM-MP method can accurately segment the lung on digital radiographs.

21 CFR 182.3225 - Calcium sorbate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium sorbate. 182.3225 Section 182.3225 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives § 182.3225 Calcium sorbate. (a) Product. Calcium sorbate. (b) Conditions of use. This substance is generally recognized as...

42 CFR 460.182 - Medicaid payment.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Medicaid payment. 460.182 Section 460.182 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Payment § 460.182 Medicaid payment. (a) Under a PACE program agreement, the State administering agency...

46 CFR 182.540 - Ballast systems.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ballast systems. 182.540 Section 182.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) MACHINERY INSTALLATION Bilge and Ballast Systems § 182.540 Ballast systems. (a) Ballast piping must not be...

21 CFR 182.1748 - Sodium caseinate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium caseinate. 182.1748 Section 182.1748 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1748 Sodium caseinate. (a) Product. Sodium caseinate. (b) Conditions of use. This substance...

21 CFR 182.1125 - Aluminum sulfate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Aluminum sulfate. 182.1125 Section 182.1125 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1125 Aluminum sulfate. (a) Product. Aluminum sulfate. (b) Conditions of use. This substance...

21 CFR 182.3089 - Sorbic acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sorbic acid. 182.3089 Section 182.3089 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives § 182.3089 Sorbic acid. (a) Product. Sorbic acid. (b) Conditions of use. This substance is generally recognized as safe when...

Passport of global nuclear business. ASME code certificate acquirement and inspection practices

International Nuclear Information System (INIS)

Kawabata, Hiroyuki; Terajima, Makoto; Anami, Kazuhiro

2010-01-01

There are possibilities of Japanese nuclear industries to participate in global business such as new and additional construction of nuclear power plants in US and also Asian and other developing countries in the world. It is requisite to acquire ASME code certificate for global business participation, just as passport. This article consists of five papers on present status of ASME code certificate acquirement and inspection practices of nuclear components vendors in the area of Japanese nuclear business. Activities of JSME Committee on Power Generation Facility Codes to make JSME codes corresponded to ASME nuclear codes and standards for their international deployment are also described. (T. Tanaka)

Review of ASME nuclear codes and standards- subcommittee on repairs, replacements, and modifications

International Nuclear Information System (INIS)

Mawson, T.J.

1990-01-01

As requested by the ASME board on Nuclear Codes and Standards, the Pressure Vessel Research Committee initiated a project to review Sections III and XI of the ASME Boiler and Pressure Vessel Code for the purposes of improving, clarifying, providing transition, consistency, compatibility, and simplifying code requirements. The project was organized with six subcommittees to address various Code activities: design; tests and examinations; documentation; quality assurance; repair, replacement and modification; and general requirements. This paper discusses how the subcommittee on repair, replacement and modification was organized to review the repair, replacement and modification requirements of the ASME boiler and pressure vessel code, Section III and Section XI for Class 1, 2, and 3 and MC components and their supports, and other documents of the nuclear industry related to the repair, replacement and modification requirements of the ASME code

[Ca2+]i oscillations in ASM: relationship with persistent airflow obstruction in asthma.

Science.gov (United States)

Sweeney, David; Hollins, Fay; Gomez, Edith; Saunders, Ruth; Challiss, R A John; Brightling, Christopher E

2014-07-01

The cause of airway smooth muscle (ASM) hypercontractility in asthma is not fully understood. The relationship of spontaneous intracellular calcium oscillation frequency in ASM to asthma severity was investigated. Oscillations were increased in subjects with impaired lung function abolished by extracellular calcium removal, attenuated by caffeine and unaffected by verapamil or nitrendipine. Whether modulation of increased spontaneous intracellular calcium oscillations in ASM from patients with impaired lung function represents a therapeutic target warrants further investigation. © 2014 The Authors. Respirology published by Wiley Publishing Asia Pty Ltd on behalf of Asian Pacific Society of Respirology.

46 CFR 182.420 - Engine cooling.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Engine cooling. 182.420 Section 182.420 Shipping COAST...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.420 Engine cooling. (a) Except as otherwise provided in paragraphs (b), (c), (d), and (e) of this section, all engines must be water cooled and meet...

21 CFR 182.8985 - Zinc chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Zinc chloride. 182.8985 Section 182.8985 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Nutrients § 182.8985 Zinc chloride. (a) Product. Zinc chloride. (b) Conditions of use. This substance is generally recognized as safe when used in...

21 CFR 182.8013 - Ascorbic acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ascorbic acid. 182.8013 Section 182.8013 Food and... CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Nutrients § 182.8013 Ascorbic acid. (a) Product. Ascorbic acid. (b) Conditions of use. This substance is generally recognized as safe when used in...

Application of CAD/CAE/CAM in forging process: a review

International Nuclear Information System (INIS)

Ahmad Baharuddin Abdullah; Hamouda, A.M.S.

2005-01-01

Forging can be described as the process in which metal is plastically deformed with application of huge pressure. The process not only changes the shape but also improves the properties of the forged parts due to grain size refinement. Conventionally, the empirical trial and error method has been applied, but recently there are various tools are employed to improved product quality and economic of the process. For example, Computer Aided Design (CAD) is widely used in modeling of the process, while Computer Aided Engineering (CAE) tools have been utilized in analyzing the process. To physically demonstrate the process, Computer Aided Manufacturing (CAM) such as CNC machine has been exploited. In order to improve forging process efficiency, an integrated system that combines all advantages of CAD, CAM and CAE need to be developed. This paper presents an overview of computer aided simulation such as CAD, CAE and CAM application in forging process. (Author)

Examples on cold forged aluminium components in automotive industry

DEFF Research Database (Denmark)

Bay, Niels; Kolsgaard, A.

2000-01-01

The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

Calculation of recovery plasticity in multistage hot forging under isothermal conditions.

Science.gov (United States)

Zhbankov, Iaroslav G; Perig, Alexander V; Aliieva, Leila I

2016-01-01

A widely used method for hot forming steels and alloys, especially heavy forging, is the process of multistage forging with pauses between stages. The well-known effect which accompanies multistage hot forging is metal plasticity recovery in comparison with monotonic deformation. A method which takes into consideration the recovery of plasticity in pauses between hot deformations of a billet under isothermal conditions is proposed. This method allows the prediction of billet forming limits as a function of deformation during the forging stage and the duration of the pause between the stages. This method takes into account the duration of pauses between deformations and the magnitude of subdivided deformations. A hot isothermal upsetting process with pauses was calculated by the proposed method. Results of the calculations have been confirmed with experimental data.

Investigating ASME allowable loads with finite element analyses

International Nuclear Information System (INIS)

Mattar Neto, Miguel; Bezerra, Luciano M.; Miranda, Carlos A. de J.; Cruz, Julio R.B.

1995-01-01

The evaluation of nuclear components using finite element analysis (FEA) does not generally fall into the shell type verification adopted by the ASME Code. Consequently, the demonstration that the modes of failure are avoided sometimes is not straightforward. Allowable limits, developed by limit load theory, require the computation of shell membrane and bending stresses. How to calculate these stresses from FEA is not necessarily self-evident. One approach to be considered is to develop recommendations in a case-by-case basis for the most common pressure vessel geometries and loads based on comparison between the results of elastic and plastic FEA. In this paper, FE analyses of common 2D and complex 3D geometries are examined and discussed. It will be clear that in the cases studied, stress separation and categorization are not self-evident and simple tasks to undertake. Certain unclear recommendations of ASME Code can lead the stress analyst to non conservative designs as will be demonstrated in this paper. At the endo of this paper, taking into account comparison between elastic and elastic-plastic FE results from ANSYS some observations, suggestions and conclusions about the degree of conservatism of the ASME recommendations will be addressed. (author)

46 CFR 182.320 - Water heaters.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Water heaters. 182.320 Section 182.320 Shipping COAST...) MACHINERY INSTALLATION Auxiliary Machinery § 182.320 Water heaters. (a) A water heater must meet the...), except that an electric water heater is also acceptable if it: (1) Has a capacity of not more than 454...

Effect of Cold Forging on Microstructure and MechanicalProperties of Al/SiC Composites

Science.gov (United States)

Hanamantraygouda, M. B.; Shivakumar, B. P., Dr; Siddappa, P. N.; Sampathkumar, L.; Prashanth, L.

2018-02-01

The objective of this work was to investigate the effect of cold forging on mechanical properties and microstructural study of Al MMCs, at different wt% of SiC and forging cycle. The Al-SiC composite material was fabricated by stir casting method at different weight percentage of SiC such as 2.5, 5, 7.5 and 10%. Further, the deformation characteristics during open-die forging of Al-SiC composite at cold conditions was investigated. Cast and forged composite material was subjected to hardness test, tensile test and impact test. The grain size, microstructure behaviour was investigated using optical microscope. The results show that hardness and strength of Al-SiC composite increases and ductility decreases as compared to Al alloy in both as-cast and forged conditions. Optical microscope images showed that the distribution of SiC in Al matrix was more homogeneous in a forged composite as compared to cast one and reduction of porosity was found. Further, it showed that due to forging cycle the grain size was reduced by 30% to 35% from initial size.

Finite element simulations and experimental investigations on ductile fracture in cold forging of aluminum alloy

Science.gov (United States)

Amiri, Amir; Nikpour, Amin; Saraeian, Payam

2018-05-01

Forging is one of the manufacturing processes of aluminium parts which has two major categories: called hot and cold forging. In the cold forging, the dimensional and geometrical accuracy of final part is high. However, fracture may occur in some aluminium alloys during the process because of less workability. Fracture in cold forging can be in the form of ductile, brittle or combination of both depending on the alloy type. There are several criteria for predicting fracture in cold forging. In this study, cold forging process of 6063 aluminium alloy for three different parts is simulated in order to predict fracture. The results of numerical simulations of Freudenthal criterion is in conformity with experimental tests.

Influence of performance improvement of AP1000 nuclear island main equipment forging on manufacturing

International Nuclear Information System (INIS)

Liu Zhiying

2013-01-01

In order to comply with the 60-year design life of an AP1000 nuclear power station, higher strength and ductility requirements have been made on AP1000 nuclear island SG forgings than on CPR1000 nuclear island main equipment. In addition, bigger size of AP1000 nuclear island SG forgings increases the difficulty of manufacturing them. Insufficient recognition of these changes may cause unstable quality of forgings and possible quality problems in follow-up welding procedure. On the basis of comparison and analysis of AP1000 nuclear island SG forgings and CPR1000 nuclear island forgings, this thesis suggests clear directions for the actions we need to take. (author)

Fatores de risco para hospitalização de crianças e adolescentes asmáticos

Directory of Open Access Journals (Sweden)

Laura Lasmar

2002-08-01

Full Text Available OBJETIVO: Verificar a ocorrência e os fatores de risco associados à hospitalização de um grupo de crianças asmáticas e realizar diagnóstico da assistência à saúde desses pacientes. MÉTODOS: Foram estudados 325 pacientes (crianças e adolescentes asmáticos, registrados em um ambulatório de referência, sendo que 202 já haviam sido hospitalizados. O diagnóstico da assistência prestada foi feito por meio de formulário que abordou características gerais das hospitalizações e fatores biológicos, demográficos, socioeconômicos e os relacionados à asma. Análises univariada e multivariada foram empregadas para verificar a associação entre variáveis independentes e a ocorrência de hospitalização. RESULTADOS: Dos pacientes estudados, 62,2% já haviam sido hospitalizados durante sua moléstia, 64,9% iniciaram crises, e 60,9% se internaram no primeiro ano de vida. A maioria (76,0% apresentava formas clínicas moderadas e graves. Apesar disto, 94,2% não estavam em uso de drogas profiláticas, recebendo assistência apenas durante o episódio agudo. Nenhum dos pacientes se encontrava vinculado à atenção primária para controle periódico da doença e profilaxia com corticosteróides inalados. Os familiares (97,8% não dispunham de conhecimentos básicos necessários ao manejo da asma. Os principais fatores de risco para hospitalização foram: a idade de início dos sintomas antes de 12 meses de idade (OR=3,20, IC95%, 1,55-6,61 ou entre 12 e 24 meses (OR=3,89, IC95%, 1,62-9,36, a escolaridade materna inferior a sete anos de estudos (OR=3,06, IC95%, 1,62-5,76, a gravidade da doença (OR=2,32, IC95%, 1,36-3,96, o número de consultas a serviços de urgência igual ou superior a duas vezes por mês (OR=2,19, IC95%, 1,24-3,88 e o diagnóstico de encaminhamento de pneumonia de repetição (OR=2,00; IC95%, 1,06-3,80. CONCLUSÃO: Com vistas à redução dos índices de hospitalização, os serviços de saúde devem se organizar para

Fatores de risco para hospitalização de crianças e adolescentes asmáticos

Directory of Open Access Journals (Sweden)

Lasmar Laura

2002-01-01

Full Text Available OBJETIVO: Verificar a ocorrência e os fatores de risco associados à hospitalização de um grupo de crianças asmáticas e realizar diagnóstico da assistência à saúde desses pacientes. MÉTODOS: Foram estudados 325 pacientes (crianças e adolescentes asmáticos, registrados em um ambulatório de referência, sendo que 202 já haviam sido hospitalizados. O diagnóstico da assistência prestada foi feito por meio de formulário que abordou características gerais das hospitalizações e fatores biológicos, demográficos, socioeconômicos e os relacionados à asma. Análises univariada e multivariada foram empregadas para verificar a associação entre variáveis independentes e a ocorrência de hospitalização. RESULTADOS: Dos pacientes estudados, 62,2% já haviam sido hospitalizados durante sua moléstia, 64,9% iniciaram crises, e 60,9% se internaram no primeiro ano de vida. A maioria (76,0% apresentava formas clínicas moderadas e graves. Apesar disto, 94,2% não estavam em uso de drogas profiláticas, recebendo assistência apenas durante o episódio agudo. Nenhum dos pacientes se encontrava vinculado à atenção primária para controle periódico da doença e profilaxia com corticosteróides inalados. Os familiares (97,8% não dispunham de conhecimentos básicos necessários ao manejo da asma. Os principais fatores de risco para hospitalização foram: a idade de início dos sintomas antes de 12 meses de idade (OR=3,20, IC95%, 1,55-6,61 ou entre 12 e 24 meses (OR=3,89, IC95%, 1,62-9,36, a escolaridade materna inferior a sete anos de estudos (OR=3,06, IC95%, 1,62-5,76, a gravidade da doença (OR=2,32, IC95%, 1,36-3,96, o número de consultas a serviços de urgência igual ou superior a duas vezes por mês (OR=2,19, IC95%, 1,24-3,88 e o diagnóstico de encaminhamento de pneumonia de repetição (OR=2,00; IC95%, 1,06-3,80. CONCLUSÃO: Com vistas à redução dos índices de hospitalização, os serviços de saúde devem se organizar para

Simulation and analysis of hot forging process for industrial locking gear elevators

Science.gov (United States)

Maarefdoust, M.; Kadkhodayan, M.

2010-06-01

In this paper hot forging process for industrial locking gear elevators is simulated and analyzed. An increase in demand of industrial locking gear elevators with better quality and lower price caused the machining process to be replaced by hot forging process. Production of industrial locking gear elevators by means of hot forging process is affected by many parameters such as billet temperature, geometry of die and geometry of pre-formatted billet. In this study the influences of billet temperature on effective plastic strain, radius of die corners on internal stress of billet and thickness of flash on required force of press are investigated by means of computer simulation. Three-dimensional modeling of initial material and die are performed by Solid Edge, while simulation and analysis of forging are performed by Super Forge. Based on the computer simulation the required dies are designed and the workpieces are formed. Comparison of simulation results with experimental data demonstrates great compatibility.

ASM LabCap's contributions to disease surveillance and the International Health Regulations (2005).

Science.gov (United States)

Specter, Steven; Schuermann, Lily; Hakiruwizera, Celestin; Sow, Mah-Séré Keita

2010-12-03

The revised International Health Regulations [IHR(2005)], which requires the Member States of the World Health Organization (WHO) to develop core capacities to detect, assess, report, and respond to public health threats, is bringing new challenges for national and international surveillance systems. As more countries move toward implementation and/or strengthening of their infectious disease surveillance programs, the strengthening of clinical microbiology laboratories becomes increasingly important because they serve as the first line responders to detect new and emerging microbial threats, re-emerging infectious diseases, the spread of antibiotic resistance, and the possibility of bioterrorism. In fact, IHR(2005) Core Capacity #8, "Laboratory", requires that laboratory services be a part of every phase of alert and response.Public health laboratories in many resource-constrained countries require financial and technical assistance to build their capacity. In recognition of this, in 2006, the American Society for Microbiology (ASM) established an International Laboratory Capacity Building Program, LabCap, housed under the ASM International Board. ASM LabCap utilizes ASM's vast resources and its membership's expertise-40,000 microbiologists worldwide-to strengthen clinical and public health laboratory systems in low and low-middle income countries. ASM LabCap's program activities align with HR(2005) by building the capability of resource-constrained countries to develop quality-assured, laboratory-based information which is critical to disease surveillance and the rapid detection of disease outbreaks, whether they stem from natural, deliberate or accidental causes.ASM LabCap helps build laboratory capacity under a cooperative agreement with the U.S. Centers for Disease Control and Prevention (CDC) and under a sub-contract with the Program for Appropriate Technology in Health (PATH) funded by the United States Agency for International Development (USAID

Research into Oil-based Colloidal-Graphite Lubricants for Forging of Al-based Alloys

International Nuclear Information System (INIS)

Petrov, A.; Petrov, P.; Petrov, M.

2011-01-01

The presented paper describes the topical problem in metal forging production. It deals with the choice of an optimal lubricant for forging of Al-based alloys. Within the scope of the paper, the properties of several oil-based colloidal-graphite lubricants were investigated. The physicochemical and technological properties of these lubricants are presented. It was found that physicochemical properties of lubricant compositions have an influence on friction coefficient value and quality of forgings.The ring compression method was used to estimate the friction coefficient value. Hydraulic press was used for the test. The comparative analysis of the investigated lubricants was carried out. The forging quality was estimated on the basis of production test. The practical recommendations were given to choose an optimal oil-based colloidal-graphite lubricant for isothermal forging of Al-based alloy.

Study on the microstructure of the different parts for new aluminum alloy forgings

International Nuclear Information System (INIS)

Gao Wei; Zheng Xiaojing; Wu Fu

2014-01-01

The mechanical properties of former aluminium alloy forgings cannot achieve technique demand. Because the component, dimension and preparation technology of new aluminum alloy have changed, the microstructure and mechanical properties of forgings are researched. It is concluded that the flowline of forgings has good continuity and uniformity, it does not have a prominent difference on microhardness of different parts. The results prove that the microstructure of forgings has good consistency. The matrix structure of forgings consists of fiber texture and equiaxed structure. The residual second phases, which are harmful to mechanical properties, are observed in the equiaxed structure. The center of equiaxed structure core zone, the edge of equiaxed structure transition zone and equiaxed structure edge zone should be focus on observing test, they are the sampling location of tensile property. (authors)

75 FR 70689 - Kaiser Aluminum Fabricated Products, LLC; Kaiser Aluminum-Greenwood Forge Division; Currently...

Science.gov (United States)

2010-11-18

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-70,376] Kaiser Aluminum Fabricated Products, LLC; Kaiser Aluminum- Greenwood Forge Division; Currently Known As Contech Forgings, LLC..., applicable to workers of Kaiser Aluminum Fabricated Products, LLC, Kaiser Aluminum-Greenwood Forge Division...

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

Energy Technology Data Exchange (ETDEWEB)

John, P K; Anto, Y; Mungikar, C P; Wagh, P M [Nuclear Power Corporation of India Ltd., Tarapur (India). Tarapur Atomic Power Station

1994-12-31

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs.

ASME section XI: rules for inservice inspection of nuclear power plants -an introspection

International Nuclear Information System (INIS)

John, P.K.; Anto, Y.; Mungikar, C.P.; Wagh, P.M.

1994-01-01

Section XI of the ASME BPV code is addressed to the examination, test and inspection requirements of the components of nuclear power plants (NPPs). Since its inception in 1970, this code section has undergone vast changes -probably the most among other ASME BPV code sections. Section XI is full fledged and lays down requirements with regard to all preservice inspections, inservice inspection, repair and replacement of components, tests of system etc. Tarapur Atomic Power Station (TAPS) has the distinction of being one of the earliest BWR type NPPs in the world that has an inservice inspection programme organised in line with the ASME section XI requirements. This paper summarises the experiences gained from time to time using this code section and a few suggestions to prospective users. An effort is also made to explain the philosophy of inservice inspection from ASME section XI point of view. 3 refs

2 CFR 182.655 - Individual.

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Individual. 182.655 Section 182.655 Grants and Agreements OFFICE OF MANAGEMENT AND BUDGET GOVERNMENTWIDE GUIDANCE FOR GRANTS AND AGREEMENTS... Individual. Individual means a natural person. ...

Technical requirements for the ASME PRA standard for nuclear power plant applications

International Nuclear Information System (INIS)

Fleming, Karl N.; Bernsen, Sidney A.; Simard, Ronald L.

2000-01-01

In 1998 the American Society of Mechanical Engineers (ASME) formed the Committee on Nuclear Risk Management (CNRM) and a Project Team to develop a standard on PRAs for use in risk informed applications. This ASME standard is being developed to help provide an adequate level of quality in PRAs that are being used to support ASME initiatives to risk informed in-service inspection (ISI) and in-service testing (IST) of nuclear power plant components. A related need supported by the industry and the U.S. Nuclear Regulatory Commission is to reduce the level of effort that is being expended in pilot applications of risk informed initiatives to address questions about the sufficiency of quality in the supporting PRA models. The purpose of this paper is to discuss the authors' views on some of the technical issues that were encountered in the effort to develop the ASME PRA standard. Draft 12 of this standard has been issued for comment, and is currently being finalized with the aim of releasing the standard in early 2001. (author)

Numerical modelling of damage evolution in ingot forging

DEFF Research Database (Denmark)

Christiansen, Peter; Martins, Paulo A.F.; Bay, Niels Oluf

2015-01-01

The ingot forging process is numerically simulated applying both the Shima-Oyane porous plasticity model as a coupled damage model and the uncoupled normalized Cockcroft & Latham criterion. Four different cases including two different lower die angles (120º and 180º) and two different sizes of feed...... (400mm and 800mm) are analysed. Comparison of the simulation results with recommendations in literature on ingot forging, indicates the normalized Cockcroft & Latham damage criterion to be the most realistic of the two....

Manufacturing and material properties of ultralarge size forgings for advanced BWRPV

International Nuclear Information System (INIS)

Suzuki, Komei; Sato, Ikuo; Tsukada, Hisashi

1994-01-01

Ultralarge size forgings for the advanced boiling water reactor (ABWR) pressure vessel as represented by the bottom petal made from a 600ton ingot have been developed. The bottom petal is a larger wall thickness ring with 10 integrated nozzles inside and outside the ring. The outer diameter is 7.8m, the height is 1.8m and the wall thickness if 1.1m in the as-forged condition. A very high purity level of P≤qslant0.003% and S≤qslant0.003% can be obtained by the application of double-refining processes to all the molten steel. The forging shows a homogeneous chemical distribution, sound internal qualities and adequate impact properties.This paper summarizes the manufacturing technique and material properties of large size forgings such as the bottom petal, the shell with integrated skirt and the bottom dome. ((orig.))

Investigation of the influence of hybrid layers on the life time of hot forging dies

Directory of Open Access Journals (Sweden)

S. Legutko

2013-04-01

Full Text Available The paper deals with the issues related in the process of drop forging with special attention paid to the durability of forging tools. It presents the results of industrial investigation of the influence of hybrid layers on hot forging dies. The effectiveness of hybrid layers type nitrided layer/PVD coating applied for extending the life of forging tools whose working surfaces are exposed to such complex exploitation conditions as, among others, cyclically varying high thermal and mechanical loads, as well as intensive abrasion at raised temperature. The examination has been performed on a set of forging tools made of Unimax steel and intended for forging steel rings of gear box synchronizer in the factory FAS in Swarzedz (Poland.

Techniques for intergranular crack formation and assessment in alloy 600 base and alloy 182 weld metals

International Nuclear Information System (INIS)

Lee, Tae Hyun; Hwang, Il Soon; Kim, Hong Deok; Kim, Ji Hyun

2015-01-01

A technique developed to produce artificial intergranular stress corrosion cracks in structural components was applied to thick, forged alloy 600 base and alloy 182 weld metals for use in the qualification of nondestructive examination techniques for welded components in nuclear power plants. An externally controlled procedure was demonstrated to produce intergranular stress corrosion cracks that are comparable to service-induced cracks in both the base and weld metals. During the process of crack generation, an online direct current potential drop method using array probes was used to measure and monitor the sizes and shapes of the cracks. A microstructural characterization of the produced cracks revealed realistic conformation of the crack faces unlike those in machined notches produced by an electrodischarge machine or simple fatigue loading using a universal testing machine. A comparison with a destructive metallographic examination showed that the characteristics, orientations, and sizes of the intergranular cracks produced in this study are highly reproducible.

Microstructure evolution and mechanical properties of a particulate reinforced magnesium matrix composites forged at elevated temperatures

International Nuclear Information System (INIS)

Deng, K.K.; Wu, K.; Wang, X.J.; Wu, Y.W.; Hu, X.S.; Zheng, M.Y.; Gan, W.M.; Brokmeier, H.G.

2010-01-01

SiCp/AZ91 magnesium matrix composite was fabricated by stir casting. The as-cast ingots were cut into cylindrical billets, and then forged at different temperatures (320, 370, 420, 470 and 520 deg. C) at a constant RAM speed of 15 mm/s with 50% reduction. The microstructure evolution of the composites during forging was investigated by optical microscope, scanning electron microscope, and transmission electron microscope. The texture of the forged composites was measured by neutron diffraction. Mechanical properties of the composite at different forging temperatures were tested by tensile tests at room temperature. It was found that a strong basal plane texture formed during forging, and the intensity of basal plane texture weakened as forging temperatures increased. The particle distribution in the composite was significantly improved by hot forging. Typical microstructures were obtained after forging at different temperatures and the composite with different microstructures offered different mechanical properties during tensile test.

Analysis of Filling and Stresses in the Hot Forging Process Depending on Flange Die Shapes

International Nuclear Information System (INIS)

Kim, Jun Hyoung; Kim, Cheol

2010-01-01

Hot closed-forging process and the die used for forming an automotive flange were analyzed from the viewpoints of heat transfer, grain-flow lines, and stresses to obtain a forged product without defects such as surface cracks, laps, cold shots, and partial filling. The forging process including up-set, pre-forging, final forging and pressing forces was investigated using finite element analysis. The influence of the preform die and the ratio of the heights of the upper die to lower die on the forging process and die were investigated and a die shape (10 .deg. for the preform die, and 1.5:1 ratio for the final die) suitable to achieve successful forging was determined on the basis of a parametric study. All parametric design requirements such as strength, full filling, and a load limit of 13,000 KN were satisfied for this newly developed flange die. New dies and flanges were fabricated and investigated. Defects such as partial filling and surface cracks were not observed

Physical modeling and numerical simulation of V-die forging ingot with central void

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2014-01-01

Numerical simulation and physical modeling performed on small-scale ingots made from pure lead, having a hole drilled through their centerline to mimic porosity, are utilized to characterize the deformation mechanics of a single open die forging compression stage and to identify the influence...... of the lower V-die angle on porosity closure and forging load requirements of large cast ingots. Results show that a lower V-die angle of 120 provides the best closure of centerline porosity without demanding the highest forging loads or developing unreasonably asymmetric shapes that may create difficulties...... in multi-stage open die forging procedures....

High yttria ferritic ODS steels through powder forging

Science.gov (United States)

Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

2017-05-01

Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y2O3 (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility.

76 FR 66996 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Forging...

Science.gov (United States)

2011-10-28

... for OMB Review; Comment Request; Forging Machines ACTION: Notice. SUMMARY: The Department of Labor... collection request (ICR) titled, ``Forging Machines,'' to the Office of Management and Budget (OMB) for....218, it is mandatory for covered employers to conduct and to document periodic inspections of forging...

Interpreting ASME limits and philosophy in FEA of pressure vessel parts

International Nuclear Information System (INIS)

Bezerra, L.M.; Cruz, J.R.B.; Miranda, C.A.J.; Neto, M.M.

1995-01-01

In recent years there has been an effort to interpret finite element (FE) stress results on the light of the ASME B and PV rules and philosophy. Many task groups have issued guidelines on stress linearization and classifications. All those attempts have come up trying to cope modern FE techniques with the rules imposed by the ASME Code. This paper is an independent contribution to the Pressure Vessel Research Council (PVRC) groups which are studying the stress classification and the failure mechanism in a FE framework. This work tries to complement the interesting work by Hollinger and Hechmer presented in the PVP-94 in Minneapolis. In that paper, the authors examined a typical support skirt and showed relations between the skirt collapse load obtained by finite element analysis and the loads allowed from the ASME stress limits. To complement such paper, in the present article, different skirt geometry configurations are analyzed. The configurations here investigated consist of similar support skirts but with different angles of attachments between cylinder and cone parts. It will be possible to observe the influence of the bending stress in the collapse load and its relation to the allowable loads inferred from the ASME limits. A pressure vessel with torispherical head under internal pressure is also examined. Using elastic and limit load FEA, the present paper determines the collapse loads of the configurations. It sets up the relations between these collapse loads, stress categories, and limits dictated by the ASME Code Subsection NB. On the light of NB rules and philosophy, this paper shows how different methods of stress assessment, classification, and limits may influence in the design of a pressure vessel

14 CFR 330.31 - What data must air carriers submit concerning ASMs or RTMs?

Science.gov (United States)

2010-01-01

... combination passenger/cargo carrier, you must have submitted your August 2001 total completed ASM report to... correct an error that you document to the Department, you must not alter the ASM or RTM reports you...

Technical Challenge and Demonstration of Advanced Solution Monitoring and Measurement System (ASMS)

International Nuclear Information System (INIS)

Takaya, A.; Mukai, Y.; Nakamura, H.; Hosoma, T.; Yoshimoto, K.; Tamura, T.; Iwamoto, T.

2010-01-01

JNFL and JAEA have collaboratively started to develop an Advanced Solution Measurement and monitoring System (ASMS) as a part of technical challenge intended for next generation safeguards NDA equipment. After we completed feasibility study by using small detectors, the second stage of ASMS has installed into PCDF tank located in a cell, and then tested and calibrated by Pu nitrate solution experimentally. There was no experience measuring around 50kg Pu inventory directly, so it was very challenging work. The conventional SMMS (Solution Monitoring and Measurement System) that is composed of precision manometers acquires density, level and temperature of solution, so that the sampling and analysis are essential to obtain the nuclear material amount in the tank. The SMMS has two weak points on verification and monitoring of the nuclear material flow and inventory; (1) Direct measurement of the inventory cannot be done, (2) Solution rework and reagent adjustment operation in actual plant will make miss-interpretation on the monitoring evaluation. The purpose of ASMS development is to establish quantitative plutonium mass measurement technique directly by NDA of high concentrated pure plutonium nitrate solution and monitoring capability for solution transfers in a process. The merits of ASMS are considered below; (1) Provide direct Pu measurement and continuous monitoring capability, (2) Eliminate sampling and analysis at IIV, (3) Reduce unmeasured inventory. The target of the measurement uncertainty of ASMS is set less than 6% (1sigma) which is equivalent to meet the detection level of the partial defect at IIV by NDA. Known-alpha coincidence counting technique is applied to the ASMS, which is similar to the NDAs for MOX powder as a principle measurement technique. Especially, three following points are key techniques to establish ASMS. (1) Pre-determination of plutonium isotopic composition because it impacts alpha and rho-zero values to obtain multiplication

Design and Analysis of a Forging Die for Manufacturing of Multiple Connecting Rods

Science.gov (United States)

Megharaj, C. E.; Nagaraj, P. M.; Jeelan Pasha, K.

2016-09-01

This paper demonstrates to utilize the hammer capacity by modifying the die design such that forging hammer can manufacture more than one connecting rod in a given forging cycle time. To modify the die design study is carried out to understand the parameters that are required for forging die design. By considering these parameters, forging die is designed using design modelling tool solid edge. This new design now can produce two connecting rods in same capacity hammer. The new design is required to validate by verifying complete filing of metal in die cavities without any defects in it. To verify this, analysis tool DEFORM 3D is used in this project. Before start of validation process it is require to convert 3D generated models in to. STL file format to import the models into the analysis tool DEFORM 3D. After importing these designs they are analysed for material flow into the cavities and energy required to produce two connecting rods in new forging die design. It is found that the forging die design is proper without any defects and also energy graph shows that the forging energy required to produce two connecting rods is within the limit of that hammer capacity. Implementation of this project increases the production of connecting rods by 200% in less than previous cycle time.

Design Procedure of Graphite Components by ASME HTR Codes

Energy Technology Data Exchange (ETDEWEB)

Kang, Ji-Ho; Jo, Chang Keun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study, the ASME B and PV Code, Subsection HH, Subpart A, design procedure for graphite components of HTRs was reviewed and the differences from metal materials were remarked. The Korean VHTR has a prismatic core which is made of multiple graphite blocks, reflectors, and core supports. One of the design issues is the assessment of the structural integrity of the graphite components because the graphite is brittle and shows quite different behaviors from metals in high temperature environment. The American Society of Mechanical Engineers (ASME) issued the latest edition of the code for the high temperature reactors (HTR) in 2015. In this study, the ASME B and PV Code, Subsection HH, Subpart A, Graphite Materials was reviewed and the special features were remarked. Due the brittleness of graphites, the damage-tolerant design procedures different from the conventional metals were adopted based on semi-probabilistic approaches. The unique additional classification, SRC, is allotted to the graphite components and the full 3-D FEM or equivalent stress analysis method is required. In specific conditions, the oxidation and viscoelasticity analysis of material are required. The fatigue damage rule has not been established yet.

Design Procedure of Graphite Components by ASME HTR Codes

International Nuclear Information System (INIS)

Kang, Ji-Ho; Jo, Chang Keun

2016-01-01

In this study, the ASME B and PV Code, Subsection HH, Subpart A, design procedure for graphite components of HTRs was reviewed and the differences from metal materials were remarked. The Korean VHTR has a prismatic core which is made of multiple graphite blocks, reflectors, and core supports. One of the design issues is the assessment of the structural integrity of the graphite components because the graphite is brittle and shows quite different behaviors from metals in high temperature environment. The American Society of Mechanical Engineers (ASME) issued the latest edition of the code for the high temperature reactors (HTR) in 2015. In this study, the ASME B and PV Code, Subsection HH, Subpart A, Graphite Materials was reviewed and the special features were remarked. Due the brittleness of graphites, the damage-tolerant design procedures different from the conventional metals were adopted based on semi-probabilistic approaches. The unique additional classification, SRC, is allotted to the graphite components and the full 3-D FEM or equivalent stress analysis method is required. In specific conditions, the oxidation and viscoelasticity analysis of material are required. The fatigue damage rule has not been established yet

Development and efficiency assessment of process lubrication for hot forging

Science.gov (United States)

Kargin, S.; Artyukh, Viktor; Ignatovich, I.; Dikareva, Varvara

2017-10-01

The article considers innovative technologies in testing and production of process lubricants for hot bulk forging. There were developed new compositions of eco-friendly water-graphite process lubricants for hot extrusion and forging. New approaches to efficiency assessment of process lubricants are developed and described in the following article. Laboratory and field results are presented.

The ASM Curriculum Guidelines for Undergraduate Microbiology: A Case Study of the Advocacy Role of Societies in Reform Efforts.

Science.gov (United States)

Horak, Rachel E A; Merkel, Susan; Chang, Amy

2015-05-01

A number of national reports, including Vision and Change in Undergraduate Biology Education: A Call to Action, have called for drastic changes in how undergraduate biology is taught. To that end, the American Society for Microbiology (ASM) has developed new Curriculum Guidelines for undergraduate microbiology that outline a comprehensive curriculum for any undergraduate introductory microbiology course or program of study. Designed to foster enduring understanding of core microbiology concepts, the Guidelines work synergistically with backwards course design to focus teaching on student-centered goals and priorities. In order to qualitatively assess how the ASM Curriculum Guidelines are used by educators and learn more about the needs of microbiology educators, the ASM Education Board distributed two surveys to the ASM education community. In this report, we discuss the results of these surveys (353 responses). We found that the ASM Curriculum Guidelines are being implemented in many different types of courses at all undergraduate levels. Educators indicated that the ASM Curriculum Guidelines were very helpful when planning courses and assessments. We discuss some specific ways in which the ASM Curriculum Guidelines have been used in undergraduate classrooms. The survey identified some barriers that microbiology educators faced when trying to adopt the ASM Curriculum Guidelines, including lack of time, lack of financial resources, and lack of supporting resources. Given the self-reported challenges to implementing the ASM Curriculum Guidelines in undergraduate classrooms, we identify here some activities related to the ASM Curriculum Guidelines that the ASM Education Board has initiated to assist educators in the implementation process.

The ASM Curriculum Guidelines for Undergraduate Microbiology: A Case Study of the Advocacy Role of Societies in Reform Efforts

Directory of Open Access Journals (Sweden)

Rachel E.A. Horak

2015-03-01

Full Text Available A number of national reports, including Vision and Change in Undergraduate Biology Education: A Call to Action, have called for drastic changes in how undergraduate biology is taught. To that end, the American Society for Microbiology (ASM developed new Curriculum Guidelines for undergraduate microbiology that outline a comprehensive curriculum for any undergraduate introductory microbiology course or program of study. Designed to foster enduring understanding of core microbiology concepts, the Guidelines work synergistically with backwards course design to focus teaching on student-centered goals and priorities.  In order to qualitatively assess how the ASM Curriculum Guidelines are used by educators and learn more about the needs of microbiology educators, the ASM Education Board distributed two surveys to the ASM education community. In this report, we discuss results of these surveys (353 responses. We found that the ASM Curriculum Guidelines are being implemented in many different types of courses at all undergraduate levels. Educators indicated that the ASM Curriculum Guidelines were very helpful when planning courses and assessments. We discuss some specific ways in which the ASM Curriculum Guidelines have been used in undergraduate classrooms. The survey identified some barriers that microbiology educators faced when trying to adopt the ASM Curriculum Guidelines, including lack of time, lack of financial resources, and lack of supporting resources. Given the self-reported challenges to implementing the ASM Curriculum Guidelines in undergraduate classrooms, we identify here some activities related to the ASM Curriculum Guidelines that the ASM Education Board has initiated to assist educators in the implementation process.

Development of strategies for saving energy by temperature reduction in warm forging processes

Science.gov (United States)

Varela, Sonia; Santos, Maite; Vadillo, Leire; Idoyaga, Zuriñe; Valbuena, Óscar

2016-10-01

This paper is associated to the European policy of increasing efficiency in raw material and energy usage. This policy becomes even more important in sectors consuming high amount of resources, like hot forging industry, where material costs sums up to 50% of component price and energy ones are continuously raising. The warm forging shows a clear potential of raw material reduction (near-net-shape components) and also of energy saving (forging temperature under 1000°C). However and due to the increment of the energy costs, new solutions are required by the forging sector in order to reduce the temperature below 900°C. The reported research is based on several approaches to reduce the forging temperature applied to a flanged shaft of the automotive sector as demonstration case. The developed investigations have included several aspects: raw material, process parameters, tools and dies behavior during forging process and also metallographic evaluation of the forged parts. This paper summarizes analysis of the ductility and the admissible forces of the flanged shaft material Ck45 in as-supplied state (as-rolled) and also in two additional heat treated states. Hot compression and tensile tests using a GLEEBLE 3800C Thermo mechanical simulator have been performed pursuing this target. In the same way, a coupled numerical model based on Finite Element Method (FEM) has been developed to predict the material flow, the forging loads and the stresses on the tools at lower temperature with the new heat treatments of the raw material. In order to validate the previous development, experimental trials at 850 °C and 750 °C were carried out in a mechanical press and the results were very promising.

ASME Section XI philosophy related to operating nuclear plant fatigue damage protection

International Nuclear Information System (INIS)

Gosselin, S.R.

1995-01-01

When faced with operating fatigue concerns, nuclear plants traditionally look to the requirements contained in the original construction design code, ASME Section 3, as a basis for component operability. These rules constitute the requirements for nuclear power plant vessel and component construction and, when combined with the Owner's Design Specification, provide reasonable assurance of reliable operation. However, once construction is complete and operation begins, the purpose of any subsequent evaluations shifts from component ''design qualification'' to component ''fitness for service.'' This is a role that has been assumed for ASME Section 11. This paper presents a philosophy, recently endorsed by the ASME Section 11 Executive Committee, intended to guide future Code activities regarding fatigue and its impact on component serviceability

Analysis of the thermo-mechanical deformations in a hot forging tool by numerical simulation

International Nuclear Information System (INIS)

L-Cancelos, R.; Varas, F.; Viéitez, I.; Martín, E.

2016-01-01

Although programs have been developed for the design of tools for hot forging, its design is still largely based on the experience of the tool maker. This obliges to build some test matrices and correct their errors to minimize distortions in the forged piece. This phase prior to mass production consumes time and material resources, which makes the final product more expensive. The forging tools are usually constituted by various parts made of different grades of steel, which in turn have different mechanical properties and therefore suffer different degrees of strain. Furthermore, the tools used in the hot forging are exposed to a thermal field that also induces strain or stress based on the degree of confinement of the piece. Therefore, the mechanical behaviour of the assembly is determined by the contact between the different pieces. The numerical simulation allows to analyse different configurations and anticipate possible defects before tool making, thus, reducing the costs of this preliminary phase. In order to improve the dimensional quality of the manufactured parts, the work presented here focuses on the application of a numerical model to a hot forging manufacturing process in order to predict the areas of the forging die subjected to large deformations. The thermo-mechanical model developed and implemented with free software (Code-Aster) includes the strains of thermal origin, strains during forge impact and contact effects. The numerical results are validated with experimental measurements in a tooling set that produces forged crankshafts for the automotive industry. The numerical results show good agreement with the experimental tests. Thereby, a very useful tool for the design of tooling sets for hot forging is achieved. (paper)

Analysis of the thermo-mechanical deformations in a hot forging tool by numerical simulation

Science.gov (United States)

L-Cancelos, R.; Varas, F.; Martín, E.; Viéitez, I.

2016-03-01

Although programs have been developed for the design of tools for hot forging, its design is still largely based on the experience of the tool maker. This obliges to build some test matrices and correct their errors to minimize distortions in the forged piece. This phase prior to mass production consumes time and material resources, which makes the final product more expensive. The forging tools are usually constituted by various parts made of different grades of steel, which in turn have different mechanical properties and therefore suffer different degrees of strain. Furthermore, the tools used in the hot forging are exposed to a thermal field that also induces strain or stress based on the degree of confinement of the piece. Therefore, the mechanical behaviour of the assembly is determined by the contact between the different pieces. The numerical simulation allows to analyse different configurations and anticipate possible defects before tool making, thus, reducing the costs of this preliminary phase. In order to improve the dimensional quality of the manufactured parts, the work presented here focuses on the application of a numerical model to a hot forging manufacturing process in order to predict the areas of the forging die subjected to large deformations. The thermo-mechanical model developed and implemented with free software (Code-Aster) includes the strains of thermal origin, strains during forge impact and contact effects. The numerical results are validated with experimental measurements in a tooling set that produces forged crankshafts for the automotive industry. The numerical results show good agreement with the experimental tests. Thereby, a very useful tool for the design of tooling sets for hot forging is achieved.

Use of Neuber's rule to estimate the fatigue life of notched specimens of ASME SA 106-B steel piping in 2880C air

International Nuclear Information System (INIS)

Terrell, J.B.

1989-01-01

Fatigue strain-life tests were conducted on notched specimens of ADMESA 106-B piping steel at PWR operating temperatures (288 0 C (550 0 F)), under completely reversed loading. Fatigue limits at 10 7 cycles were estimated for smooth specimens to be 185 M Pa (26.8 ksi) at 24 0 C and 232 MPa (33.7 ksi) at 288 0 C. The higher fatigue strength observed at the PWR temperature is postulated to be caused by dynamic strain aging processes. However, a reduction in fatigue strength in the low cycle fatigue regime was observed in 288 0 C air environment tests, which may indicate that the current ASME Section III design curve for carbon steels is nonconservative in its positioning. Notch strain histories were estimated for the notched specimen tests using various interpretations of Neuber's rule. It was concluded that the use of the fatigue notch concentration factor (K f ) in the Neuber relation in conjunction with the uniaxial cyclic stress-strain curve provided the best correlation of notched specimen fatigue data with results obtained from smooth specimen tests. The notched specimen strain-life results derived from the application of Neuber's rule alone proved to be conservative when compared with smooth specimen test results to such an extent that Neuber-generated notch stresses and strain amplitudes cannot accurately be compared with the mean data curves derived from the ASME Section III fatigue curves for carbon steels which are based on net section stress measurements. (author)

The structural and phase state formed in construction titanium alloy by radial forging

Energy Technology Data Exchange (ETDEWEB)

Shlyakhova, Galina V.; Danilov, Vladimir I.; Orlova, Dina V.; Zuev, Lev B. [Institute of Strength Physics and Materials Science SB RAS, Tomsk (Russian Federation); Zavodchikov, Aleksandr S. [Perm State Technical University, Perm (Russian Federation)

2011-07-01

The feasibility of rod manufacture from construction titanium alloy using radial forging on a high duty machine SXK16 was investigated. The investigations were carried on for titanium rod samples using the methods of metallography, electron transmission microscophy and X-ray analysis. The results obtained are described herein. It is found that radial forging results in the formation of homogeneous fine-grained structure.Using radial forging process, high-quality items are produced. As-worked material has submicrocrystalline globular structure and an optimal α:β phase ratio. Besides, the technology is more cost-effective relative to conventional flow charts. Key words: forging, titanium alloy, fine-grain structure, substructure, pore size.

Controlled austempering of hammer forgings aimed at pseudo normalized microstructure directly after deformation

Directory of Open Access Journals (Sweden)

P. Skubisz

2017-01-01

Full Text Available The study concerns cost-effective realization of controlled thermomechanical processing (CTMP of medium-carbon and HSLA steel aimed at producing microstructure and properties equivalent to normalized condition directly after forging. The results of theoretical and physical modeling of hot forging with subsequent heat treating adopted for industrial realization in continuous manner were verified in semi-industrial conditions of a forge plant.

Research on Energy-Saving Production Scheduling Based on a Clustering Algorithm for a Forging Enterprise

Directory of Open Access Journals (Sweden)

Yifei Tong

2016-02-01

Full Text Available Energy efficiency is a buzzword of the 21st century. With the ever growing need for energy efficient and low-carbon production, it is a big challenge for high energy-consumption enterprises to reduce their energy consumption. To this aim, a forging enterprise, DVR (the abbreviation of a forging enterprise, is researched. Firstly, an investigation into the production processes of DVR is given as well as an analysis of forging production. Then, the energy-saving forging scheduling is decomposed into two sub-problems. One is for cutting and machining scheduling, which is similar to traditional machining scheduling. The other one is for forging and heat treatment scheduling. Thirdly, former forging production scheduling is presented and solved based on an improved genetic algorithm. Fourthly, the latter is discussed in detail, followed by proposed dynamic clustering and stacking combination optimization. The proposed stacking optimization requires making the gross weight of forgings as close to the maximum batch capacity as possible. The above research can help reduce the heating times, and increase furnace utilization with high energy efficiency and low carbon emissions.

Researching on knowledge architecture of design by analysis based on ASME code

International Nuclear Information System (INIS)

Bao Shiyi; Zhou Yu; He Shuyan

2003-01-01

The quality of knowledge-based system's knowledge architecture is one of decisive factors of knowledge-based system's validity and rationality. For designing the ASME code knowledge based system, this paper presents a knowledge acquisition method which is extracting knowledge through document analysis consulted domain experts' knowledge. Then the paper describes knowledge architecture of design by analysis based on the related rules in ASME code. The knowledge of the knowledge architecture is divided into two categories: one is empirical knowledge, and another is ASME code knowledge. Applied as the basement of the knowledge architecture, a general procedural process of design by analysis that is met the engineering design requirements and designers' conventional mode is generalized and explained detailed in the paper. For the sake of improving inference efficiency and concurrent computation of KBS, a kind of knowledge Petri net (KPN) model is proposed and adopted in expressing the knowledge architecture. Furthermore, for validating and verifying of the empirical rules, five knowledge validation and verification theorems are given in the paper. Moreover the research production is applicable to design the knowledge architecture of ASME codes or other engineering standards. (author)

21 CFR 182.1180 - Caffeine.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Caffeine. 182.1180 Section 182.1180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN....1180 Caffeine. (a) Product. Caffeine. (b) Tolerance. 0.02 percent. (c) Limitations, restrictions, or...

Approaching application of risk-based inspection to ASME code section XI

International Nuclear Information System (INIS)

Hedden, Owen F.

1995-01-01

This paper will describe current efforts within the ASME Boiler and Pressure Vessel Committee's Subcommittee on Nuclear Inservice Inspection to introduce risk-based technology to optimize inservice inspection of nuclear power plants. The subcommittee is responsible for the content of ASME Boiler and Pressure Vessel Code Section XI, Rules for Inservice Inspection of Nuclear Power Plant Components. The paper will first provide the historical background for the inspection program currently in Section XI. It will then describe the development of new technology through the ASME Center for Research and Technology Development program. Next, the work now going on in two of the groups under the Section XI committee will be described in detail. Each of these two efforts is directed toward the application of new risk-based inspection technology to nuclear piping systems. Finally, the directions of additional research and applications of the technology will be discussed. (author)

Structural and functional analysis of the ASM p.Ala359Asp mutant that causes acid sphingomyelinase deficiency.

Science.gov (United States)

Acuña, Mariana; Castro-Fernández, Víctor; Latorre, Mauricio; Castro, Juan; Schuchman, Edward H; Guixé, Victoria; González, Mauricio; Zanlungo, Silvana

2016-10-21

Niemann-Pick disease (NPD) type A and B are recessive hereditary disorders caused by deficiency in acid sphingomyelinase (ASM). The p.Ala359Asp mutation has been described in several patients but its functional and structural effects in the protein are unknown. In order to characterize this mutation, we modeled the three-dimensional ASM structure using the recent available crystal of the mammalian ASM as a template. We found that the p.Ala359Asp mutation is localized in the hydrophobic core and far from the sphingomyelin binding site. However, energy function calculations using statistical potentials indicate that the mutation causes a decrease in ASM stability. Therefore, we investigated the functional effect of the p.Ala359Asp mutation in ASM expression, secretion, localization and activity in human fibroblasts. We found a 3.8% residual ASM activity compared to the wild-type enzyme, without changes in the other parameters evaluated. These results support the hypothesis that the p.Ala359Asp mutation causes structural alterations in the hydrophobic environment where ASM is located, decreasing its enzymatic activity. A similar effect was observed in other previously described NPDB mutations located outside the active site of the enzyme. This work shows the first full size ASM mutant model describe at date, providing a complete analysis of the structural and functional effects of the p.Ala359Asp mutation over the stability and activity of the enzyme. Copyright © 2016 Elsevier Inc. All rights reserved.

Improvement of mechanical properties of zirconia-toughened alumina by sinter forging

NARCIS (Netherlands)

He, Y.; Winnubst, Aloysius J.A.; Verweij, H.; Burggraaf, Anthonie; Burggraaf, A.J.

1994-01-01

ZTA powder with a composition of 85 wt% alumina/15 wt% zirconia was prepared by a gel precipitation method. Sinter forging was performed with this powder to enhance the mechanical properties of ZTA materials. The influence of processing flaws on mechanical properties of sinter forged materials and

47 CFR 36.182 - Cash working capital.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Cash working capital. 36.182 Section 36.182... PROCEDURES; STANDARD PROCEDURES FOR SEPARATING TELECOMMUNICATIONS PROPERTY COSTS, REVENUES, EXPENSES, TAXES... Cash Working Capital § 36.182 Cash working capital. (a) The amount for cash working capital, if not...

Comparative Thermal Aging Effects on PM-HIP and Forged Inconel 690

Science.gov (United States)

Bullens, Alexander L.; Bautista, Esteban; Jaye, Elizabeth H.; Vas, Nathaniel L.; Cain, Nathan B.; Mao, Keyou; Gandy, David W.; Wharry, Janelle P.

2018-03-01

This study compares thermal aging effects in Inconel 690 (IN690) produced by forging and powder metallurgy with hot isostatic pressing (PM-HIP). Isothermal aging is carried out over 400-800°C for up to 1000 h and then metallography and nanoindentation are utilized to relate grain microstructure with hardness and yield strength. The PM-HIP IN690 maintains a constant grain size through all aging conditions, while the forged IN690 exhibits limited grain growth at the highest aging temperature and longest aging time. The PM-HIP IN690 exhibits comparable mechanical integrity as the forged material throughout aging: hardness and yield strength are unchanged with 100 h aging, but increase after 1000 h aging at all temperatures. In both the PM-HIP and forged IN690, the Hall-Petch relationship for Ni-based superalloys predicts yield strength for 0-100 h aged specimens, but underestimates yield strength in the 1000 h aged specimens because of thermally induced precipitation.

Roles of the outer membrane protein AsmA of Salmonella enterica in the control of marRAB expression and invasion of epithelial cells.

Science.gov (United States)

Prieto, Ana I; Hernández, Sara B; Cota, Ignacio; Pucciarelli, M Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

2009-06-01

A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S. enterica, suggesting that lack of AsmA activates expression of the marRAB operon. Hence, asmA mutations may enhance bile resistance by inducing gene expression changes in the marRAB-controlled Mar regulon. In silico analysis of AsmA structure predicted the existence of one transmembrane domain. Biochemical analysis of subcellular fractions revealed that the asmA gene of S. enterica encodes a protein of approximately 70 kDa located in the outer membrane. Because AsmA is unrelated to known transport and/or efflux systems, we propose that activation of marRAB in asmA mutants may be a consequence of envelope reorganization. Competitive infection of BALB/c mice with asmA(+) and asmA isogenic strains indicated that lack of AsmA attenuates Salmonella virulence by the oral route but not by the intraperitoneal route. Furthermore, asmA mutants showed a reduced ability to invade epithelial cells in vitro.

The approach to analysis of significance of flaws in ASME section III and section XI

International Nuclear Information System (INIS)

Cowan, A.

1979-01-01

ASME III Appendix G and ASME XI Appendix A describe linear elastic fracture mechanics methods to assess the significance of defects in thick-walled pressure vessels for nuclear reactor systems. The assessment of fracture toughness, Ksub(Ic), is based upon recommendations made by a Task Group of the USA Pressure Vessel Research Committee and is dependent upon correlations with drop weight and Charpy V-notch data to give a lower bound of fracture toughness Ksub(IR). The methods used in the ASME Appendices are outlined noting that, whereas ASME III Appendix G defines a procedure for obtaining allowable pressure vessel loadings for normal service in the presence of a defect, ASME XI Appendix A defines methods for assessing the significance of defects (found by volumetric inspection) under normal and emergency and faulted conditions. The methods of analysis are discussed with respect to material properties, flaw characterisation, stress analysis and recommended safety factors; a short discussion is given on the applicability of the data and methods to other materials and non-nuclear structures. (author)

Comparison of SKIFS 2004:1 and Tillsynshandbok PSA against the ASME PRA Standard and European requirements on PSA

International Nuclear Information System (INIS)

Hellstroem, Per

2005-04-01

Requirements on PSA for risk informed applications are expressed in different international documents. The ASME PRA standard published in spring 2002 is one such document, PSA requirements are also expressed in the European Utility Requirements (EUR) for new reactors. The Swedish PSA requirements are provided in the Swedish regulators (SKI) statutes SKIFS 2004:1. SKI also has a review handbook for PSA activities (SKI report 2003:48). The review handbook is a support during review of the utilities PSA activities and the PSAs themselves. The review handbook expresses SKIs expectations by providing so called important aspects for both the PSA work and the PSAs, A comparison of SKIFS requirements and the important aspects in the Review handbook, on one side, and the requirements on PSA in EUR and ASME on the other side, is presented. The comparison shows a large difference in the level of detail in the different documents, where ASME is most detailed and specific. This is expected since the SKI review handbook not is a 'PSA guide' in the same way as the ASME PRA standard. A direct comparison of the ASME PRA standard requirements with the important aspects in the review handbook cannot answer the question which ASME capacity level that is achieved by a PSA meeting all important aspects. The conclusion is that it is not likely to achieve capacity level 2 and 3, since very few ASME level 3 attributes are explicitly expressed as important aspects, though many are expressed in general terms. The review handbook important aspects that are most similar to the ASME capacity level 1 attributes are initiating events, sequence analysis, and system analysis while less similarity is found for analysis of operator actions data analysis, quantification and containment analysis (level 2). Less similarity is found for capacity level 2 and 3. However, the number of additional ASME attributes on capacity level 2 and 3 are few. There are also important aspects in the review handbook that

21 CFR 182.1047 - Glutamic acid hydrochloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Glutamic acid hydrochloride. 182.1047 Section 182.1047 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Substances § 182.1047 Glutamic acid hydrochloride. (a) Product. Glutamic acid hydrochloride. (b...

21 CFR 182.1781 - Sodium aluminum phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium aluminum phosphate. 182.1781 Section 182.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Substances § 182.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b...

Neurospora crassa ASM-1 complements the conidiation defect in a stuA mutant of Aspergillus nidulans.

Science.gov (United States)

Chung, Dawoon; Upadhyay, Srijana; Bomer, Brigitte; Wilkinson, Heather H; Ebbole, Daniel J; Shaw, Brian D

2015-01-01

Aspergillus nidulans StuA and Neurospora crassa ASM-1 are orthologous APSES (ASM-1, PHD1, SOK2, Efg1, StuA) transcription factors conserved across a diverse group of fungi. StuA and ASM-1 have roles in asexual (conidiation) and sexual (ascospore formation) development in both organisms. To address the hypothesis that the last common ancestor of these diverse fungi regulated conidiation with similar genes, asm-1 was introduced into the stuA1 mutant of A. nidulans. Expression of asm-1 complemented defective conidiophore morphology and restored conidia production to wild type levels in stuA1. Expression of asm-1 in the stuA1 strain did not rescue the defect in sexual development. When the conidiation regulator AbaA was tagged at its C-terminus with GFP in A. nidulans, it localized to nuclei in phialides. When expressed in the stuA1 mutant, AbaA::GFP localized to nuclei in conidiophores but no longer was confined to phialides, suggesting that expression of AbaA in specific cell types of the conidiophore was conditioned by StuA. Our data suggest that the function in conidiation of StuA and ASM-1 is conserved and support the view that, despite the great morphological and ontogenic diversity of their condiphores, the last common ancestor of A. nidulans and N. crassa produced an ortholog of StuA that was involved in conidiophore development. © 2015 by The Mycological Society of America.

2 CFR 182.635 - Drug-free workplace.

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Drug-free workplace. 182.635 Section 182.635... Reserved GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Definitions § 182.635 Drug-free workplace. Drug-free workplace means a site for the performance of work done in connection...

Inservice inspection procedures and training according to the ASME code

International Nuclear Information System (INIS)

Greenwald, S.M.; Chockie, L.J.

1987-01-01

Mandatory training of the technical staff at a nuclear power plant is of paramount importance if we are to avoid costly plant shutdowns. This training should include the requirements for both Preservice and Inservice Inspection, in addition to Quality Assurance procedures as required by the American Society of Mechanical Engineers (ASME) Code. The training is best accomplished by utilizing instructors who are thoroughly familiar with plant operations and the ASME Code, as well as serving on one of the Code committees. This paper focuses on the Inservice Inspection procedures and the results of an intensive training effort to implement such procedures. (author)

Corticosteroids reduce IL-6 in ASM cells via up-regulation of MKP-1.

Science.gov (United States)

Quante, Timo; Ng, Yee Ching; Ramsay, Emma E; Henness, Sheridan; Allen, Jodi C; Parmentier, Johannes; Ge, Qi; Ammit, Alaina J

2008-08-01

The mechanisms by which corticosteroids reduce airway inflammation are not completely understood. Traditionally, corticosteroids were thought to inhibit cytokines exclusively at the transcriptional level. Our recent evidence, obtained in airway smooth muscle (ASM), no longer supports this view. We have found that corticosteroids do not act at the transcriptional level to reduce TNF-alpha-induced IL-6 gene expression. Rather, corticosteroids inhibit TNF-alpha-induced IL-6 secretion by reducing the stability of the IL-6 mRNA transcript. TNF-alpha-induced IL-6 mRNA decays at a significantly faster rate in ASM cells pretreated with the corticosteroid dexamethasone (t(1/2) = 2.4 h), compared to vehicle (t(1/2) = 9.0 h; P ASM cells.

46 CFR 182.435 - Integral fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Integral fuel tanks. 182.435 Section 182.435 Shipping...) MACHINERY INSTALLATION Specific Machinery Requirements § 182.435 Integral fuel tanks. (a) Gasoline fuel tanks must be independent of the hull. (b) Diesel fuel tanks may not be built integral with the hull of...

The ASME research task force on risk-based in-service inspection

International Nuclear Information System (INIS)

Balkey, K.R.; Chapman, O.J.V.

1997-01-01

The use of risk-based methods in the development of in-service inspection (ISI) and in-service testing (IST) programs for nuclear power plant and other industrial applications has been studied for the last several years through the American Society of Mechanical Engineers Centre for Research and Technology Development (ASME 1991, 1992, 1994, 1996). The results of this work are being used as a foundation to develop specific requirements for implementation of risk-based technology in ASME Codes and Standards, regulatory requirements and industry programs both in the U.S. and other countries. This paper provides a brief overview of the ASME Research Methodology and how it has been adapted for application to the inspection of piping within the USA. It also relates how the reliability of nondestructive examination (NDE) methods for pressure boundary components can impact the risk and discusses the relationship between this and NDE qualification/demonstration now being implemented in Europe and the USA. (orig.)

46 CFR 182.610 - Main steering gear.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Main steering gear. 182.610 Section 182.610 Shipping...) MACHINERY INSTALLATION Steering Systems § 182.610 Main steering gear. (a) A vessel must be provided with a main steering gear that is: (1) Of adequate strength and capable of steering the vessel at all service...

Fatigue in cold-forging dies: Tool life analysis

DEFF Research Database (Denmark)

Skov-Hansen, P.; Bay, Niels; Grønbæk, J.

1999-01-01

In the present investigation it is shown how the tool life of heavily loaded cold-forging dies can be predicted. Low-cycle fatigue and fatigue crack growth testing of the tool materials are used in combination with finite element modelling to obtain predictions of tool lives. In the models...... the number of forming cycles is calculated first to crack initiation and then during crack growth to fatal failure. An investigation of a critical die insert in an industrial cold-forging tool as regards the influence of notch radius, the amount and method of pre-stressing and the selected tool material...

Proceedings: 2001 ASME/EPRI Radwaste Workshop

International Nuclear Information System (INIS)

2001-01-01

Nuclear utilities continually evaluate methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has increased the emphasis on this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technology and management improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

A physically-based constitutive model for SA508-III steel: Modeling and experimental verification

International Nuclear Information System (INIS)

Dong, Dingqian; Chen, Fei; Cui, Zhenshan

2015-01-01

Due to its good toughness and high weldability, SA508-III steel has been widely used in the components manufacturing of reactor pressure vessels (RPV) and steam generators (SG). In this study, the hot deformation behaviors of SA508-III steel are investigated by isothermal hot compression tests with forming temperature of (950–1250)°C and strain rate of (0.001–0.1)s −1 , and the corresponding flow stress curves are obtained. According to the experimental results, quantitative analysis of work hardening and dynamic softening behaviors is presented. The critical stress and critical strain for initiation of dynamic recrystallization are calculated by setting the second derivative of the third order polynomial. Based on the classical stress–dislocation relation and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of SA508-III steel. Comparisons between the predicted and measured flow stress indicate that the established physically-based constitutive model can accurately characterize the hot deformations for the steel. Furthermore, a successful numerical simulation of the industrial upsetting process is carried out by implementing the developed constitutive model into a commercial software, which evidences that the physically-based constitutive model is practical and promising to promote industrial forging process for nuclear components

A physically-based constitutive model for SA508-III steel: Modeling and experimental verification

Energy Technology Data Exchange (ETDEWEB)

Dong, Dingqian [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China); Chen, Fei, E-mail: feechn@gmail.com [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China); Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Cui, Zhenshan, E-mail: cuizs@sjtu.edu.cn [National Die & Mold CAD Engineering Research Center, Shanghai Jiao Tong University, 1954 Huashan Rd., Shanghai 200030 (China)

2015-05-14

Due to its good toughness and high weldability, SA508-III steel has been widely used in the components manufacturing of reactor pressure vessels (RPV) and steam generators (SG). In this study, the hot deformation behaviors of SA508-III steel are investigated by isothermal hot compression tests with forming temperature of (950–1250)°C and strain rate of (0.001–0.1)s{sup −1}, and the corresponding flow stress curves are obtained. According to the experimental results, quantitative analysis of work hardening and dynamic softening behaviors is presented. The critical stress and critical strain for initiation of dynamic recrystallization are calculated by setting the second derivative of the third order polynomial. Based on the classical stress–dislocation relation and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of SA508-III steel. Comparisons between the predicted and measured flow stress indicate that the established physically-based constitutive model can accurately characterize the hot deformations for the steel. Furthermore, a successful numerical simulation of the industrial upsetting process is carried out by implementing the developed constitutive model into a commercial software, which evidences that the physically-based constitutive model is practical and promising to promote industrial forging process for nuclear components.

21 CFR 169.182 - Vanilla-vanillin powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b) The...

Avaliação do programa de atenção a crianças asmáticas acompanhadas nas unidades de saúde do Município do Embu, São Paulo, no período de 1988 a 1993

Directory of Open Access Journals (Sweden)

Renato Nabas Ventura

Full Text Available Com o objetivo de avaliar o desempenho do Programa de Atenção a Crianças Portadoras de "Chiado no Peito", no Município de Embu, São Paulo, foram estudadas 434 crianças e adolescentes de zero a 14 anos, admitidas no programa de maio/88 a julho/93. Mais de 90% desses pacientes nunca haviam sido acompanhados por esse motivo em serviço médico. Apenas 6,2% foram encaminhados a outros serviços de referência durante o acompanhamento no programa. Segundo critérios clínicos, os pacientes foram classificados em: bebê chiador (21,8%, asmáticos leves (41,7%, asmáticos moderados (28,3%, asmáticos graves (7,6% e outros (0,4%. Ao se analisar o comportamento dos asmáticos moderados e graves acompanhados por mais de um ano, observou-se melhora clínica nesses dois grupos, e o que influenciou positivamente esse fato foi a maior aderência ao uso da medicação. O número de exacerbações decresceu entre os asmáticos graves, após um ano de acompanhamento regular, embora durante os 12 meses analisados tenha havido um consumo praticamente constante de medicação broncodilatadora. O abandono ocorreu em 53,2% das crianças matriculadas, principalmente nos primeiros seis meses de acompanhamento, sendo significantemente mais freqüente entre os asmáticos moderados. Concluímos que as crianças com maior aderência ao programa se beneficiaram do mesmo, apesar das dificuldades e da falta de alguns recursos medicamentosos atualmente existentes.

Avaliação do programa de atenção a crianças asmáticas acompanhadas nas unidades de saúde do Município do Embu, São Paulo, no período de 1988 a 1993

Directory of Open Access Journals (Sweden)

Ventura Renato Nabas

1998-01-01

Full Text Available Com o objetivo de avaliar o desempenho do Programa de Atenção a Crianças Portadoras de "Chiado no Peito", no Município de Embu, São Paulo, foram estudadas 434 crianças e adolescentes de zero a 14 anos, admitidas no programa de maio/88 a julho/93. Mais de 90% desses pacientes nunca haviam sido acompanhados por esse motivo em serviço médico. Apenas 6,2% foram encaminhados a outros serviços de referência durante o acompanhamento no programa. Segundo critérios clínicos, os pacientes foram classificados em: bebê chiador (21,8%, asmáticos leves (41,7%, asmáticos moderados (28,3%, asmáticos graves (7,6% e outros (0,4%. Ao se analisar o comportamento dos asmáticos moderados e graves acompanhados por mais de um ano, observou-se melhora clínica nesses dois grupos, e o que influenciou positivamente esse fato foi a maior aderência ao uso da medicação. O número de exacerbações decresceu entre os asmáticos graves, após um ano de acompanhamento regular, embora durante os 12 meses analisados tenha havido um consumo praticamente constante de medicação broncodilatadora. O abandono ocorreu em 53,2% das crianças matriculadas, principalmente nos primeiros seis meses de acompanhamento, sendo significantemente mais freqüente entre os asmáticos moderados. Concluímos que as crianças com maior aderência ao programa se beneficiaram do mesmo, apesar das dificuldades e da falta de alguns recursos medicamentosos atualmente existentes.

Design and verification of thermomechanical parameters of P/M Ti6Al4V alloy forging

Energy Technology Data Exchange (ETDEWEB)

Wojtaszek, Marek, E-mail: mwojtasz@metal.agh.edu.pl; Śleboda, Tomasz

2014-12-05

Highlights: • Thermomechanical parameters of P/M Ti6Al4V alloy processing were determined. • The use of the mixture of elemental powders allows reducing manufacturing costs. • Numerical modelling allowed to elaborate favourable parameters of forging. • The industrial trials of hot forging of P/M Ti6Al4V alloy were successful. - Abstract: This work is focused on the design of technology of forging high-quality Ti6Al4V alloy by means of powder metallurgy methods. A mixture of elemental powders, with the chemical composition of that of Ti6Al4V alloy, was used as a starting material for the investigation. Powder mixtures were fully densified by hot compaction under precisely controlled conditions. The mechanical properties of the obtained compacts were examined. The mechanical behaviour of the investigated alloy powder compacts was evaluated by compression test under various thermomechanical conditions using Gleeble simulator. The microstructure of powder compacts as well as P/M alloy samples deformed in compression tests was examined. All data obtained from the experimental tests were applied as boundary conditions for numerical simulation of forging of selected forgings. Basing on the results of both plastometric tests and simulations, thermomechanical parameters of the investigated alloy forging were determined. Designed parameters of forging technology were verified by forging trials performed in industrial conditions. The quality of the obtained forgings was examined by means of computed tomography.

Effect of forging process on microstructure, mechanical and corrosion properties of biodegradable Mg-1Ca alloy

International Nuclear Information System (INIS)

Harandi, Shervin Eslami; Hasbullah Idris, Mohd; Jafari, Hassan

2011-01-01

Research highlights: → Forging temperature demonstrates more pronounced effect compared to forging speed. → Precipitation of Mg 2 Ca phase at grain boundaries accelerates corrosion rate. → Forging process doesn't provide the corrosion resistance required for bone healing. -- Abstract: The performance of Mg-1Ca alloy, a biodegradable metallic material, may be improved by hot working in order that it may be of use in bone implant applications. In this study, Mg-1Ca cast alloy was preheated to different temperatures before undergoing forging process with various forging speeds. Macro- and microstructure of the samples were examined by stereo and scanning electron microscopes (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), respectively. To determine the mechanical properties of the alloy, hardness value and plastic deformation ability of the samples were measured. To investigate the corrosion behaviour of the alloy, immersion and electrochemical tests were performed on the samples in simulated body fluid and the corrosion products were characterized by SEM/EDS. The results showed that increasing forging temperature decreased grain size led to improved hardness value and plastic deformation ability of the alloy, whereas no significant effect was observed by changing forging speed. Moreover, forging at higher temperatures led to an increase in the amount of Mg 2 Ca phase at grain boundaries resulted in higher corrosion rates. It can be concluded that although forging process improved the mechanical properties of the alloy, it does not satisfy the corrosion resistance criteria required for bone healing.

Design and verification of thermomechanical parameters of P/M Ti6Al4V alloy forging

International Nuclear Information System (INIS)

Wojtaszek, Marek; Śleboda, Tomasz

2014-01-01

Highlights: • Thermomechanical parameters of P/M Ti6Al4V alloy processing were determined. • The use of the mixture of elemental powders allows reducing manufacturing costs. • Numerical modelling allowed to elaborate favourable parameters of forging. • The industrial trials of hot forging of P/M Ti6Al4V alloy were successful. - Abstract: This work is focused on the design of technology of forging high-quality Ti6Al4V alloy by means of powder metallurgy methods. A mixture of elemental powders, with the chemical composition of that of Ti6Al4V alloy, was used as a starting material for the investigation. Powder mixtures were fully densified by hot compaction under precisely controlled conditions. The mechanical properties of the obtained compacts were examined. The mechanical behaviour of the investigated alloy powder compacts was evaluated by compression test under various thermomechanical conditions using Gleeble simulator. The microstructure of powder compacts as well as P/M alloy samples deformed in compression tests was examined. All data obtained from the experimental tests were applied as boundary conditions for numerical simulation of forging of selected forgings. Basing on the results of both plastometric tests and simulations, thermomechanical parameters of the investigated alloy forging were determined. Designed parameters of forging technology were verified by forging trials performed in industrial conditions. The quality of the obtained forgings was examined by means of computed tomography

New design of process for cold forging to improve multi-stage gas fitting

Directory of Open Access Journals (Sweden)

Han-Sung Huang

2016-04-01

Full Text Available This work develops a process that solves the problem of the formation of cracks inside forged gas fittings in the cold forging process that arises from poor forging process design. DEFORM-3D forming software was utilized, and macroscopic experiments with optical microscopy and scanning electron microscopy were conducted to investigate the processed structures and the distribution therein of metal flow lines, and to find the internal micro-cracks to determine whether the cold forging process is reasonable. Analytical results herein demonstrate that the stress and strain inside the gas fitting can be elucidated using metal forming software. Together with experimental results, they demonstrate that a concentration of stress damages the workpiece in the forming process. Moreover, as metal flow lines become narrower, the workpiece becomes more easily damaged. Consequently, the improved cold forging process that is described in this work should be utilized to reduce the occurrence of fine cracks and defects. Planning for proper die design and production, increasing the quality of products, and reducing the number of defective products promote industrial competitiveness.

Revision of the ASME nuclear quality assurance standard and its historical background

International Nuclear Information System (INIS)

Suzuki, Tetsuya

2009-01-01

ASME NQA-1-2008 'Quality Assurance Requirements for Nuclear Facility Applications' will be endorsed by US NRC by the end of 2009. This standard will apply to design, construction and operation of nuclear power plants newly erected in USA. It is important to Japanese vendors developing nuclear business in USA. Historical background, significance of revision and main revised points of the ASME nuclear quality assurance standard are described in the present paper. (T. Tanaka)

Cyclin D1 in ASM Cells from Asthmatics Is Insensitive to Corticosteroid Inhibition.

Science.gov (United States)

Allen, Jodi C; Seidel, Petra; Schlosser, Tobias; Ramsay, Emma E; Ge, Qi; Ammit, Alaina J

2012-01-01

Hyperplasia of airway smooth muscle (ASM) is a feature of the remodelled airway in asthmatics. We examined the antiproliferative effectiveness of the corticosteroid dexamethasone on expression of the key regulator of G(1) cell cycle progression-cyclin D1-in ASM cells from nonasthmatics and asthmatics stimulated with the mitogen platelet-derived growth factor BB. While cyclin D1 mRNA and protein expression were repressed in cells from nonasthmatics in contrast, cyclin D1 expression in asthmatics was resistant to inhibition by dexamethasone. This was independent of a repressive effect on glucocorticoid receptor translocation. Our results corroborate evidence demonstrating that corticosteroids inhibit mitogen-induced proliferation only in ASM cells from subjects without asthma and suggest that there are corticosteroid-insensitive proliferative pathways in asthmatics.

Managing Tensions And Forging Creative Synergies Between ...

African Journals Online (AJOL)

Managing Tensions And Forging Creative Synergies Between Indigenous And Modern Settlement Planning Concepts And Practices: Lessons For The Design And Planning For Sustainable Settlements And Built-Forms In Southern Africa.

Strain-induced grain growth of cryomilled nanocrystalline Al in trimodal composites during forging

International Nuclear Information System (INIS)

Yao, B.; Simkin, B.; Majumdar, B.; Smith, C.; Bergh, M. van den; Cho, K.; Sohn, Y.H.

2012-01-01

Highlights: ► Grain growth of cryomilled nanocrystalline aluminum during hot forging. ► Use of hollow cone dark field imaging technique in TEM for grain size measurement. ► Grain growth model of strain, strain rate and temperature for forging optimization. - Abstract: Grain growth of nanocrystalline aluminum ( nc Al) in trimodal Al metal-matrix-composites (MMCs) during hot forging was investigated. The nc Al phase formed through cryomilling of inert gas-atomized powders in liquid nitrogen has an average grain size down to 21 nm, exhibits excellent thermal stability. However, substantial grain growth of nc Al up to 63 nm was observed when the Al MMCs were thermo-mechanically processed even at relatively low temperatures. Grain growth of the cryomilled nc Al phase in trimodal Al MMCs after hot forging was documented with respect to temperature ranging from 175 °C to 287 °C, true strain ranging from 0.4 to 1.35 and strain rate ranging from 0.1 to 0.5 s −1 . Hollow cone dark field imaging technique was employed to provide statistically confident measurements of nc Al grain size that ranged from 21 to 63 nm. An increase in forging temperature and an increase in true strain were correlated with an increase in grain size of nc Al. Results were correlated to devise a phenomenological grain growth model for forging that takes strain, strain rate and temperature into consideration. Activation energy for the grain growth during thermo-mechanical hot-forging was determined to be 35 kJ/mol, approximately a quarter of activation energy for bulk diffusion of Al and a half of activation energy for static recrystallization.

Proceedings: 2000 ASME/EPRI Radwaste Workshop

International Nuclear Information System (INIS)

2001-01-01

Nuclear utilities are continually evaluating methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has added increased emphasis to this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technological and managerial improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

Forged Signature Distinction Using Convolutional Neural Network for Feature Extraction

Directory of Open Access Journals (Sweden)

Seungsoo Nam

2018-01-01

Full Text Available This paper proposes a dynamic verification scheme for finger-drawn signatures in smartphones. As a dynamic feature, the movement of a smartphone is recorded with accelerometer sensors in the smartphone, in addition to the moving coordinates of the signature. To extract high-level longitudinal and topological features, the proposed scheme uses a convolution neural network (CNN for feature extraction, and not as a conventional classifier. We assume that a CNN trained with forged signatures can extract effective features (called S-vector, which are common in forging activities such as hesitation and delay before drawing the complicated part. The proposed scheme also exploits an autoencoder (AE as a classifier, and the S-vector is used as the input vector to the AE. An AE has high accuracy for the one-class distinction problem such as signature verification, and is also greatly dependent on the accuracy of input data. S-vector is valuable as the input of AE, and, consequently, could lead to improved verification accuracy especially for distinguishing forged signatures. Compared to the previous work, i.e., the MLP-based finger-drawn signature verification scheme, the proposed scheme decreases the equal error rate by 13.7%, specifically, from 18.1% to 4.4%, for discriminating forged signatures.

Distribution of Microstructure and Vickers Hardness in Spur Bevel Gear Formed by Cold Rotary Forging

Directory of Open Access Journals (Sweden)

Wuhao Zhuang

2014-11-01

Full Text Available Cold rotary forging is a novel metal forming technology which is widely used to produce the high performance gears. Investigating the microstructure and mechanical property of cold rotary forged gears has a great significance in improving their service performance. In this study, the grain morphology in different regions of the spur bevel gear which is processed by cold rotary forging is presented. And the distribution regulars of the grain deformation and Vickers hardness in the transverse and axial sections of the gear tooth are studied experimentally. A three-dimensional rigid-plastic FE model is developed to simulate the cold rotary forging process of a spur bevel gear under the DEFORM-3D software environment. The variation of effective strain in the spur bevel gear has been investigated so as to explain the distribution regulars of the microstructure and Vickers hardness. The results of this research thoroughly reveal the inhomogeneous deformation mechanisms in cold rotary forging of spur bevel gears and provide valuable guidelines for improving the performance of cold rotary forged spur bevel gears.

Rethinking ASME III seismic analysis for piping operability evaluations

International Nuclear Information System (INIS)

Adams, T.M.; Stevenson, J.D.

1994-01-01

It has been recognized since the mid 1980's that there are very large seismic margins to failure for nuclear piping systems when designed using current industry practice, design criteria, and methods. As a result of this realization there are or have been approximately eighteen initiatives within the ASME , Boiler and Pressure Vessel Code Section III, Division 1, in the form of proposed code cases and proposed code text changes designed to reduce these failure margins to more realistic values. For the most part these initiatives have concentrated on reclassifying seismic inertia stresses in the piping as secondary and increasing the allowable stress limits permitted by Section III of the ASME, Boiler Code. This paper focuses on the application of non-linear spectral analysis methods as a method to reduce the input seismic demand determination and thereby reduce the seismic failure margins. The approach is evaluated using the ASME Boiler Pressure Vessel Code Section III Subgroup on Design benchmark procedure as proposed by the Subgroup's Special Task Group on Integrated Piping Criteria. Using this procedure, criteria are compared to current code criterion and analysis methods, and several other of the currently proposed Boiler and Pressure Vessel, Section III, changes. Finally, the applicability of the non-linear spectral analysis to continued Safe Operation Evaluations is reviewed and discussed

76 FR 30200 - Forging Machines; Extension of the Office of Management and Budget's (OMB) Approval of...

Science.gov (United States)

2011-05-24

...] Forging Machines; Extension of the Office of Management and Budget's (OMB) Approval of Information... extend OMB approval of the information collection requirements contained in the Forging Machines Standard... to reduce employees' risk of death or serious injury by ensuring that forging machines used by them...

Effect of Forging Allowance Value on the Power Consumption of Machining Process

Directory of Open Access Journals (Sweden)

L. D. Mal'kova

2015-01-01

Full Text Available The paper aim is to develop and study possible energy-efficiency measures for machined forgings drawing on analysis of the impact of the allowance for machining and its scatter.The most sophisticated option to take into consideration the effect of the cut depth is the work-piece machining in which the forging allowance value results from the blank production.Research of power consumption was conducted for turning the cylindrical surface of 144 mm length and  1,5 33 0,5   diameter on forgings of the work-pieces "screw of steering control" made from steel 60PP. A radial dimension allowance at said cylindrical surface at six points of the five sections was sized to assess the allowance value dispersion. The size of the sample measurements at the control points was n = 600. Statistic processing has shown normal law of distribution and sample homogeneity.To analyze the results of experiments was calculated a range of allowances for this workpiece. Calculated minimum and maximum allowance per one side for rough lathing were, respectively, 0.905 mm and 1.905mm. It was found that 77% points under control lie in calculated range of allowance values. And there are no points out of the range on lesser side that proves a lack of rejects; but there are points out of the range on the bigger side, that will require additional costs for machining the specified surface, including the cost of electricity.There were three power consumption calculations based on factory- recommended duty: for processing the entire sample of forgings with an average allowance, for machining forgings allowances of which are within the recommended design range of allowance, and for processing the entire sample of forgings with a minimum value of allowance.It was found that elimination of allowance values which are outside the recommended range enables to reduce the power consumption, at least, by 6%, and the overall power consumption for processing the measured forgings

Interaction between endoplasmic/sarcoplasmic reticulum stress (ER/SR stress), mitochondrial signaling and Ca(2+) regulation in airway smooth muscle (ASM).

Science.gov (United States)

Delmotte, Philippe; Sieck, Gary C

2015-02-01

Airway inflammation is a key aspect of diseases such as asthma. Several inflammatory cytokines (e.g., TNFα and IL-13) increase cytosolic Ca(2+) ([Ca(2+)]cyt) responses to agonist stimulation and Ca(2+) sensitivity of force generation, thereby enhancing airway smooth muscle (ASM) contractility (hyper-reactive state). Inflammation also induces ASM proliferation and remodeling (synthetic state). In normal ASM, the transient elevation of [Ca(2+)]cyt induced by agonists leads to a transient increase in mitochondrial Ca(2+) ([Ca(2+)]mito) that may be important in matching ATP production with ATP consumption. In human ASM (hASM) exposed to TNFα and IL-13, the transient increase in [Ca(2+)]mito is blunted despite enhanced [Ca(2+)]cyt responses. We also found that TNFα and IL-13 induce reactive oxidant species (ROS) formation and endoplasmic/sarcoplasmic reticulum (ER/SR) stress (unfolded protein response) in hASM. ER/SR stress in hASM is associated with disruption of mitochondrial coupling with the ER/SR membrane, which relates to reduced mitofusin 2 (Mfn2) expression. Thus, in hASM it appears that TNFα and IL-13 result in ROS formation leading to ER/SR stress, reduced Mfn2 expression, disruption of mitochondrion-ER/SR coupling, decreased mitochondrial Ca(2+) buffering, mitochondrial fragmentation, and increased cell proliferation.

Computer Οptimization of Geometric Form of Tool and Preform for Closed-die Forging of Compressor Blade Simulator

Directory of Open Access Journals (Sweden)

A. V. Botkin

2014-07-01

Full Text Available Using the software package DEFORM 3D when developing technology of isothermal forging workpiece blades it is possible to reduce the pre-production time, to improve the quality of forgings and increase lifetime of forging dies. Computer modeling allows to predict the formation of such defects during forging as notches and wrinkles, underfilling of die impression, to estimate tool loads. Preform shape and angular position of the blade simulator were optimized in order to minimize the lateral forces generated during the forging operation.

Manufacture of large monoblock LP rotor forgings and their quality

International Nuclear Information System (INIS)

Suzuki, Akira; Kinoshita, Shushi; Kohno, Masayoshi; Miyakawa, Mutsuhiro; Kikuchi, Hideo

1986-01-01

This paper describes the manufacturing and the quality of large monoblock low pressure rotors forged from 360 ton and 420 ton ingots. To obtain good and homogenous mechanical properties throughout a rotor, a computer was used to determine the heat treatment conditions. It was found that the technique was very effective at predicting mechanical properties of a monoblock rotor. Mechanical properties including the fracture toughness and fatigue crack propagation characteristics of monoblock rotor forgings proved satisfactory. (author)

Identification of forged Bank of England £20 banknotes using IR spectroscopy.

Science.gov (United States)

Sonnex, Emily; Almond, Matthew J; Baum, John V; Bond, John W

2014-01-24

Bank of England notes of £20 denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. An aim of this work was to develop a non-destructive method so that a small, compact Fourier transform infrared spectrometer (FT-IR) instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 cm(-1) arising from νasym (CO3(2-)) from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine £20 notes were observed in the ν(OH) (ca. 3500 cm(-1)), ν(C-H) (ca. 2900 cm(-1)) and ν(C=O) (ca. 1750 cm(-1)) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper. Copyright © 2013 Elsevier B.V. All rights reserved.

Identification of forged Bank of England £20 banknotes using IR spectroscopy

Science.gov (United States)

Sonnex, Emily; Almond, Matthew J.; Baum, John V.; Bond, John W.

2014-01-01

Bank of England notes of £20 denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. An aim of this work was to develop a non-destructive method so that a small, compact Fourier transform infrared spectrometer (FT-IR) instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 cm-1 arising from νasym (CO32-) from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine £20 notes were observed in the ν(OH) (ca. 3500 cm-1), ν(Csbnd H) (ca. 2900 cm-1) and ν(Cdbnd O) (ca. 1750 cm-1) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper.

Intersubjective decision-making for computer-aided forging technology design

Science.gov (United States)

Kanyukov, S. I.; Konovalov, A. V.; Muizemnek, O. Yu.

2017-12-01

We propose a concept of intersubjective decision-making for problems of open-die forging technology design. The intersubjective decisions are chosen from a set of feasible decisions using the fundamentals of the decision-making theory in fuzzy environment according to the Bellman-Zadeh scheme. We consider the formalization of subjective goals and the choice of membership functions for the decisions depending on subjective goals. We study the arrangement of these functions into an intersubjective membership function. The function is constructed for a resulting decision, which is chosen from a set of feasible decisions. The choice of the final intersubjective decision is discussed. All the issues are exemplified by a specific technological problem. The considered concept of solving technological problems under conditions of fuzzy goals allows one to choose the most efficient decisions from a set of feasible ones. These decisions correspond to the stated goals. The concept allows one to reduce human participation in automated design. This concept can be used to develop algorithms and design programs for forging numerous types of forged parts.

21 CFR 182.1045 - Glutamic acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Glutamic acid. 182.1045 Section 182.1045 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN....1045 Glutamic acid. (a) Product. Glutamic acid. (b) [Reserved] (c) Limitations, restrictions, or...

The relationship between UT reported size and actual size of the defects in rotor forgings

International Nuclear Information System (INIS)

Seong, Un Hak; Kim, Jeong Tae; Park, Yun Sik

2003-01-01

In order to evaluate the reliability of rotor forgings, it is very important to know the actual size of the defects in the rotor forgings. The determination of the defect size requires the accurate non-destructive measurement. However, there may be some differences between the reported size with the ultrasonic non-destructive testing method and the actual size of defects. These differences may be a severe cause of errors in evaluation of rotor forgings. So, the calculated size with 'Master Curve' considering safety factor, which is usually larger than the reported size, has been used in evaluation of rotor forgings. The relation between the EFBH (Equivalent Flat Bottom Hole) size measured by non-destructive method and the actual size by destructive method in many rotors manufactured at Doosan was investigated. In this investigation 'Master Curve' compensating the differences between UT reported size and actual size of defects in our rotor forgings was obtainable. The applicability of this 'Master Curve' as a way of calculating the actual defect size was also investigated. For the evaluation of rotor forgings, it is expected that this 'Master Curve' may be used to determine the accurate actual size of defects.

The relationship between UT reported size and actual size of the defects in rotor forgings

International Nuclear Information System (INIS)

Seong, Un Hak; Kim, Jeong Tae; Park, Yun Sik

2003-01-01

In order to evaluate the reliability of rotor forgings, it is very important to know the actual size of the defects in the rotor forgings. The determination of the defect size requires the accurate non-destructive measurement. However, there may be some difference between the reported size with ultrasonic non-destructive testing method and the actual size of defects. These differences may be a severe cause of errors in evaluation of rotor forgings. So, the calculated size with 'Master Curve' considering safety factor, which is usually larger than the reported size, has been used in evaluation of rotor forgings. The relation between the EFBH (Equivalent Flat Bottom Hole) size measured by non-destructive method and the actual size by destructive method in many rotors manufactured at Doosan was investigated. In this investigation, 'Master Curve' compensating the differences between UT reported size and actual size of defects in our rotor forgings was obtainable. The applicability of this 'Master Curve' as a way of calculating the actual defect size was also investigated. For the evaluation of rotor forgings, it is expected that this 'Master Curve' may be used to determine the accurate actual size of defects.

Fabrication and properties of Y-Ba-Cu-O high Tc superconductor by upset-forging method

International Nuclear Information System (INIS)

Chang, Ho Jung; Kang, Kae Myung; Song, Jin Tae

1990-01-01

YBa 2 Cu 3 O 7-x oxide superconductors was fabricated by sintering process and upset-forging method, respectively, and microstructures and conduction properties were compared. There was no difference in crystal structure the (001) x-ray reflection presumably due to preferred crystal orientation of the YBa 2 Cu 3 O 7-x superconductor. Furthermore, the grain size of the 123-phase increased as the reduction ratio became larger during the upset-forging. The critical temperature for zero resistivity of both samples was almost the same, i.e., about 90K. These results have demonstrated the potential of producing YBa 2 Cu 3 O 7-x superconducting wire or tape effectively using a upset-forging method. The critical current density of the upset-forged sample, however, was lower than that of the sintered one, which fact might be ascribed to microcrack formation during fast upset-forging. (Author)

Roles of the Outer Membrane Protein AsmA of Salmonella enterica in the Control of marRAB Expression and Invasion of Epithelial Cells▿

OpenAIRE

Prieto, Ana I.; Hernández, Sara B.; Cota, Ignacio; Pucciarelli, M. Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

2009-01-01

A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S....

Nickel-base alloy forgings for advanced high temperature power plants

Energy Technology Data Exchange (ETDEWEB)

Donth, B.; Diwo, A.; Blaes, N.; Bokelmann, D. [Saarschmiede GmbH Freiformschmiede, Voelklingen (Germany)

2008-07-01

The strong efforts to reduce the CO{sub 2} emissions lead to the demand for improved thermal efficiency of coal fired power plants. An increased thermal efficiency can be realised by higher steam temperatures and pressures in the boiler and the turbine. The European development aims for steam temperatures of 700 C which requires the development and use of new materials and also associated process technology for large components. Temperatures of 700 C and above are too high for the application of ferritic steels and therefore only Nickel-Base Alloys can fulfill the required material properties. In particular the Nickel-Base Alloy A617 is the most candidate alloy on which was focused the investigation and development in several German and European programs during the last 10 years. The goal is to verify and improve the attainable material properties and ultrasonic detectability of large Alloy 617 forgings for turbine rotors and boiler parts. For many years Saarschmiede has been manufacturing nickel and cobalt alloys and is participating the research programs by developing the manufacturing routes for large turbine rotor forgings up to a maximum diameter of 1000 mm as well as for forged tubes and valve parts for the boiler side. The experiences in manufacturing and testing of very large forgings made from nickel base alloys for 700 C steam power plants are reported. (orig.)

21 CFR 182.2227 - Calcium silicate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium silicate. 182.2227 Section 182.2227 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Calcium silicate. (a) Product. Calcium silicate. (b) Tolerance. 2 percent and 5 percent. (c) Limitations...

21 CFR 182.8252 - Choline chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Choline chloride. 182.8252 Section 182.8252 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... chloride. (a) Product. Choline chloride. (b) Conditions of use. This substance is generally recognized as...

21 CFR 182.3041 - Erythorbic acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Erythorbic acid. 182.3041 Section 182.3041 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... acid. (a) Product. Erythorbic acid. (b) Conditions of use. This substance is generally recognized as...

21 CFR 182.1073 - Phosphoric acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Phosphoric acid. 182.1073 Section 182.1073 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN....1073 Phosphoric acid. (a) Product. Phosphoric acid. (b) Conditions of use. This substance is generally...

46 CFR 182.430 - Engine exhaust pipe installation.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Engine exhaust pipe installation. 182.430 Section 182... 100 GROSS TONS) MACHINERY INSTALLATION Specific Machinery Requirements § 182.430 Engine exhaust pipe... equipment might come in contact with an exhaust pipe. (b) Exhaust gas must not leak from the piping or any...

Fractography analysis of tool samples used for cold forging

DEFF Research Database (Denmark)

Dahl, K.V.

2002-01-01

Three fractured tool dies used for industrial cold forging have been investigated using light optical microscopy and scanning electron microscopy. Two of the specimens were produced using the traditional Böhler P/M steel grade s790, while the lastspecimen was a third generation P/M steel produced...... using new technology developed by Böhler. All three steels have the same nominal composition of alloying elements. The failure in both types of material occurs as a crack formation at a notch inside ofthe tool. Generally the cold forging dies constructed in third generation steels have a longer lifetime...

36 CFR 13.182 - Temporary facilities.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Temporary facilities. 13.182... NATIONAL PARK SYSTEM UNITS IN ALASKA Cabins Use of Temporary Facilities Related to Taking Fish and Wildlife § 13.182 Temporary facilities. In a national preserve where the taking of fish and wildlife is...

21 CFR 182.3013 - Ascorbic acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ascorbic acid. 182.3013 Section 182.3013 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... acid. (a) Product. Ascorbic acid. (b) Conditions of use. This substance is generally recognized as safe...

Technical justification for ASME code section xi crack detection by visual examination

International Nuclear Information System (INIS)

Nickell, R.E.; Rashid, Y.R.

2001-01-01

A critical technical element of nuclear power plant license renewal in the United States is the demonstration that the effects of aging do not compromise the intended safety function(s) of a system, structure, or component during the extended term of operation. The demonstration may take either of two forms. First, it can be shown that the design basis for the system, structure, or component is sufficiently robust that the aging effects have been insignificant through the current license term, and will continue to be insignificant through the extended term. Alternatively, it can be shown that, while the aging effects may be potentially significant, those effects can be managed and functionality maintained by defined programmatic activities during the extended term of operation. The first of the two approaches is generally provided by the construction basis, such as construction in accordance with the ASME Code Section III and other consensus codes and standards. The second of the two approaches is often provided by periodic inservice inspection and testing, in accordance with the ASME Code Section XI. The purpose of the ASME Section XI inspections and tests is to assure that systems, components, and structures are fit for continued service until the next scheduled inspection or test. The purpose of this paper is to document the effectiveness of the current ASME Code Section XI visual examination procedures in detecting the effects of aging for systems, structures, and components that are tolerant of mature cracks. (author)

Structural changes of radial forging die surface during service under thermo-mechanical fatigue

International Nuclear Information System (INIS)

Nematzadeh, Fardin; Akbarpour, Mohammad Reza; Kokabi, Amir Hosein; Sadrnezhaad, Seyed Khatiboleslam

2009-01-01

Radial forging is one of the modern open die forging techniques and has a wide application in producing machine parts. During operation at high temperatures, severe temperature change associated with mechanical loads and the resultant wearing of the die surface lead to intense variation in strain on the die surface. Therefore, under this operating condition, thermo-mechanical fatigue (TMF) occurs on the surface of the radial forging die. TMF decreases the life of the die severely. In the present research, different layers were deposited on a 1.2714 steel die by SMAW and GTAW, with a weld wire of UDIMET 520. The microstructure of the radial forging die surface was investigated during welding and service using an optical microscope and scanning electron microscope. The results revealed that, after welding, the structure of the radial forging die surface includes the γ matrix with a homogeneous distribution of fine semi-spherical carbides. The weld structure consisted mostly of columnar dendrites with low grain boundaries. Also, microstructural investigation of the die surface during operation showed that the weld structure of the die surface has remained without any considerable change. Only dendrites were deformed and broken. Moreover, grain boundaries of the dendrites were revealed during service.

Identification of Forged Bank of England 20 Gbp Banknotes Using IR Spectroscopy

Science.gov (United States)

Sonnex, Emily

2014-06-01

Bank of England notes of 20 GBP denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. A principal aim of this work was to develop a method so that a small, compact ATR FTIR instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 wn from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine 20 GBP notes were observed in the ν(OH) (ca. 3500 wn), ν(C-H) (ca. 2900 wn) and ν(C=O) (ca. 1750 wn) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper. Further to this, with an announcement by the Bank of England to produce polymer banknotes in the future, the work has been extended using Australian polymer banknotes to show that the method would be transferable.

ASME and RCC-MR comparison for the prevention of fatigue analysis

International Nuclear Information System (INIS)

Autrusson, B.; Acker, D.

1989-01-01

The purpose of this survey is to compare the simplified methods, without reference to the safety factor allowed for the mechanical properties. An application of both codes, RCC-MR and ASME, on the design of the wall mock-up of the NET project is made and also an estimation with an elastoplastic analysis. In the case of fatigue analysis according to ASME in the plastic field, the elastic stress is magnified by a K e factor derived from stress variation, S n , disregarding geometrical discontinuities. According to RCC-MR, the elastic maximum strain will magnified by two coefficients accounting for plasticity and variation of Poisson ratio

Comparison between instrumented precracked Charpy and compact specimen tests of carbon steels

International Nuclear Information System (INIS)

Nanstad, R.K.

1980-01-01

The General Atomic Company High Temperature Gas-Cooled Reactor (HTGR) is housed within a prestressed concrete reactor vessel (PCRV). Various carbon steel structural members serve as closures at penetrations in the vessel. A program of testing and evaluation is underway to determine the need for reference fracture toughness (K/sub IR/) and indexing procedures for these materials as described in Appendix G to Section III, ASME Code for light water reactor steels. The materials of interest are carbon steel forgings (SA508, Class 1) and plates (SA537, Classes 1 and 2) as well as weldments of these steels. The fracture toughness behavior is characterized with instrumented precracked Charpy V-votch specimens (PCVN) - slow-bend and dynamic - and compact specimens (10-mm and 25-mm thicknesses) using both linear elastic (ASTM E399) and elastic-plastic (equivalent Energy and J-Integral) analytical procedures. For the dynamic PCVN tests, force-time traces are analyzed according to the procedures of the Pressure Vessel Research Council (PVRC)/Metal Properties Council (MPC). Testing and analytical procedures are discussed and PCVN results are compared to those obtained with compact specimens

Simulation and optimization of a coking wastewater biological treatment process by activated sludge models (ASM).

Science.gov (United States)

Wu, Xiaohui; Yang, Yang; Wu, Gaoming; Mao, Juan; Zhou, Tao

2016-01-01

Applications of activated sludge models (ASM) in simulating industrial biological wastewater treatment plants (WWTPs) are still difficult due to refractory and complex components in influents as well as diversity in activated sludges. In this study, an ASM3 modeling study was conducted to simulate and optimize a practical coking wastewater treatment plant (CWTP). First, respirometric characterizations of the coking wastewater and CWTP biomasses were conducted to determine the specific kinetic and stoichiometric model parameters for the consecutive aeration-anoxic-aeration (O-A/O) biological process. All ASM3 parameters have been further estimated and calibrated, through cross validation by the model dynamic simulation procedure. Consequently, an ASM3 model was successfully established to accurately simulate the CWTP performances in removing COD and NH4-N. An optimized CWTP operation condition could be proposed reducing the operation cost from 6.2 to 5.5 €/m(3) wastewater. This study is expected to provide a useful reference for mathematic simulations of practical industrial WWTPs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Basic requirements of mechanical properties for nuclear pressure vessel materials in ASME-BPV code

International Nuclear Information System (INIS)

Ning Dong; Yao Weida

2011-01-01

The four basic aspects of strengths, ductility, toughness and fatigue strengths can be summarized for overall mechanical properties requirements of materials for nuclear pressure-retaining vessels in ASME-BPV code. These mechanical property indexes involve in the factors of melting, manufacture, delivery conditions, check or recheck for mechanical properties and chemical compositions, etc. and relate to degradation and damage accumulation during the use of materials. This paper specifically accounts for the basic requirements and theoretic basis of mechanical properties for nuclear pressure vessel materials in ASME-BPV code and states the internal mutual relationships among the four aspects of mechanical properties. This paper focuses on putting forward at several problems on mechanical properties of materials that shall be concerned about during design and manufacture for nuclear pressure vessels according to ASME-BPV code. (author)

Manufacturing of Nanostructured Rings from Previously ECAE-Processed AA5083 Alloy by Isothermal Forging

Directory of Open Access Journals (Sweden)

C. J. Luis

2013-01-01

Full Text Available The manufacturing of a functional hollow mechanical element or ring of the AA5083 alloy previously equal channel angular extrusion (ECAE processed, which presents a submicrometric microstructure, is dealt with. For this purpose, the design of two isothermal forging dies (preform and final shape is carried out using the design of experiments (DOE methodology. Moreover, after manufacturing the dies and carrying out tests so as to achieve real rings, the mechanical properties of these rings are analysed as well as their microstructure. Furthermore, a comparison between the different forged rings is made from ECAE-processed material subjected to different heat treatments, previous to the forging stage. On the other hand, the ring forging process is modelled through the use of finite element simulation in order to improve the die design and to study the force required for the isothermal forging, the damage value, and the strain the material predeformed by ECAE has undergone. With this present research work, it is intended to improve the knowledge about the mechanical properties of nanostructured material and the applicability of this material to industrial processes that allow the manufacturing of functional parts.

2016 Accomplishments. Tritium aging studies on stainless steel. Forging process effects on the fracture toughness properties of tritium-precharged stainless steel

Energy Technology Data Exchange (ETDEWEB)

Morgan, Michael J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-01-01

Forged austenitic stainless steels are used as the materials of construction for pressure vessels designed to contain tritium at high pressure. These steels are highly resistant to tritium-assisted fracture but their resistance can depend on the details of the forging microstructure. During FY16, the effects of forging strain rate and deformation temperature on the fracture toughness properties of tritium-exposed-and-aged Type 304L stainless steel were studied. Forgings were produced from a single heat of steel using four types of production forging equipment – hydraulic press, mechanical press, screw press, and high-energy-rate forging (HERF). Each machine imparted a different nominal strain rate during the deformation. The objective of the study was to characterize the J-Integral fracture toughness properties as a function of the industrial strain rate and temperature. The second objective was to measure the effects of tritium and decay helium on toughness. Tritium and decay helium effects were measured by thermally precharging the as-forged specimens with tritium gas at 34.5 MPa and 350°C and aging for up to five years at -80°C to build-in decay helium prior to testing. The results of this study show that the fracture toughness properties of the as-forged steels vary with forging strain rate and forging temperature. The effect is largely due to yield strength as the higher-strength forgings had the lower toughness values. For non-charged specimens, fracture toughness properties were improved by forging at 871°C versus 816°C and Screw-Press forgings tended to have lower fracture toughness values than the other forgings. Tritium exposures reduced the fracture toughness values remarkably to fracture toughness values averaging 10-20% of as-forged values. However, forging strain rate and temperature had little or no effect on the fracture toughness after tritium precharging and aging. The result was confirmed by fractography which indicated that fracture modes

Función adrenal y metabolismo lipídico en niños asmáticos tratados con budesonida

Directory of Open Access Journals (Sweden)

Paoli-de Valeri Mariela

1999-01-01

Full Text Available Objetivo. Evaluar el efecto de bajas dosis de budesonida inhalado sobre la función adrenal y el metabolismo lipídico en niños asmáticos. Material y métodos. Se estudiaron: 10 niños asmáticos (edad promedio, 8.6 años tratados con budesonida inhalado (200-300 µg/día por un lapso mayor a tres meses (grupo A; 15 niños asmáticos (edad promedio, 7.8 años sin tratamiento esteroideo (grupo B, y 10 niños no asmáticos (grupo C. Se determinaron los niveles de cortisol basal y postestímulo con ACTH, andrógenos adrenales, lípidos y cortisol urinario. Resultados. Entre los grupos A y B no hubo diferencias significativas en las variables estudiadas. En los niños asmáticos (grupo A-B el cortisol urinario fue significativamente mayor en relación con el grupo C. Los niveles de triglicéridos, colesterol total, colesterol de la lipoproteína de baja densidad e índices aterogénicos fueron mayores en el grupo de niños asmáticos, con y sin budesonida, comparados con el grupo C. Conclusiones. El tratamiento con dosis bajas de budesonida inhalado en niños asmáticos no modificó la función del eje adrenal ni el metabolismo lipídico. Los pacientes asmáticos presentaron un perfil lipídico aterogénico que podría incrementar el riesgo de enfermedad cardiovascular.

Bibliometric Analyses Reveal Patterns of Collaboration between ASMS Members

Science.gov (United States)

Palmblad, Magnus; van Eck, Nees Jan

2018-03-01

We have explored the collaborative network of the current American Society for Mass Spectrometry (ASMS) membership using bibliometric methods. The analysis shows that 4249 members are connected in a single, large, co-authorship graph, including the majority of the most published authors in the field of mass spectrometry. The map reveals topographical differences between university groups and national laboratories, and that the co-authors with the strongest links have long worked together at the same location. We have collected and summarized information on the geographical distribution of members, showing a high coverage of active researchers in North America and Western Europe. Looking at research fields, we could also identify a number of new or `hot' topics among ASMS members. Interactive versions of the maps are available on-line at https://goo.gl/UBNFMQ (collaborative network) and https://goo.gl/WV25vm (research topics). [Figure not available: see fulltext.

The 1997 NRC IST workshops and the status of questions and issues directed to the ASME O and M committee

International Nuclear Information System (INIS)

DiBiasio, A.M.

1998-05-01

This paper describes the results of the four NRC Inservice Testing (IST) Workshops which were held in early 1997 pertaining to NRC Inspection Procedure P 73756, Inservice Testing of Pumps and Valves. It also presents the status of the ASME code committees' resolution of certain questions forwarded to the ASME by the NRC. These questions relate to code interpretations, inconsistencies in the code, and industry concerns that are most appropriately resolved through the ASME consensus process. The ASME committees reviewed the questions at their December 1997 and March 1998 code meetings. Of particular interest are those questions for which the ASME code committees did not agree with the NRC response. These questions, as well as those which the committees provided some additional insight or input, are presented in this paper

A Retrospective Look at 20 Years of ASM Education Programs (1990-2010 and a Prospective Look at the Next 20 Years (2011-2030

Directory of Open Access Journals (Sweden)

Amy Chang

2011-03-01

Full Text Available The Education Board of the American Society for Microbiology (ASM was established in the mid-1970s to address the graduate and medical education needs of ASM members. Since then, I have watched our offerings evolve from a small, graduate-level travel grant program for ASM meetings to a growing suite of professional development and networking opportunities including fellowships, publications, and conferences. Along the way, our audience has expanded from  graduate students to undergraduate biology and K-12 teachers, students of all ages, researchers, and the public.I have been fortunate enough to watch several pivotal programs and projects support our growth and change the status quo by providing opportunities for biology educators to flourish. These include the: (i Coalition for Education in the Life Sciences, (ii ASM Division on Microbiology Education, (iii ASM Conference for Undergraduate Educators, (iv ASM Journal of Microbiology & Biology Education, and (v ASM Fellowship Fund. In this review, the background and details I offer on each initiative help explain ASM Education offerings, how our growth has been supported, and where are we headed.

[A method of temperature measurement for hot forging with surface oxide based on infrared spectroscopy].

Science.gov (United States)

Zhang, Yu-cun; Qi, Yan-de; Fu, Xian-bin

2012-05-01

High temperature large forging is covered with a thick oxide during forging. It leads to a big measurement data error. In this paper, a method of measuring temperature based on infrared spectroscopy is presented. It can effectively eliminate the influence of surface oxide on the measurement of temperature. The method can measure the surface temperature and emissivity of the oxide directly using the infrared spectrum. The infrared spectrum is radiated from surface oxide of forging. Then it can derive the real temperature of hot forging covered with the oxide using the heat exchange equation. In order to greatly restrain interference spectroscopy through included in the received infrared radiation spectrum, three interference filter system was proposed, and a group of optimal gap parameter values using spectral simulation were obtained. The precision of temperature measurement was improved. The experimental results show that the method can accurately measure the surface temperature of high temperature forging covered with oxide. It meets the requirements of measurement accuracy, and the temperature measurement method is feasible according to the experiment result.

Transmission electron microscopy of Ti-12Mo-13Nb Alloy aged after heat forging

International Nuclear Information System (INIS)

Oliveira, Nathalia Rodrigues; Baldan, Renato; Gabriel, Sinara Borborema

2014-01-01

Metastable β-Ti alloys possess mechanical properties, in particular a elastic modulus that depends not only on its composition but also the applied thermomechanical treatments. These alloys require high mechanical strength and a low Young’s modulus to avoid stress shielding. Preliminary studies on the development of Ti- 13Nb-12Mo alloy showed than the better properties were obtained at aged at 500 ° C / 24 h after cold forging , whose microstructure consisted of bimodal α phase in the β matrix. In this work, Ti-12Mo-13Nb alloy was heat forged and aged at 500 deg C for 24h and the microstructure was analyzed by employing X-ray diffraction and transmission electron microscopy. According to the results, while the cold forging resulted in bimodal α phase in the β matrix, hot forging resulted in a fine and homogeneous α phase in the β matrix. (author)

Modelling and Testing of Friction in Forging

DEFF Research Database (Denmark)

Bay, Niels

2007-01-01

Knowledge about friction is still limited in forging. The theoretical models applied presently for process analysis are not satisfactory compared to the advanced and detailed studies possible to carry out by plastic FEM analyses and more refined models have to be based on experimental testing...

Forging Inclusive Solutions: Experiential Earth Charter Education

Science.gov (United States)

Hill, Linda D.

2010-01-01

Forging Inclusive Solutions describes the aims, methodology and outcomes of Inclusive Leadership Adventures, an experiential education curriculum for exploring the Earth Charter. Experiential education builds meaningful relationships, skills, awareness and an inclusive community based on the Earth Charter principles. When we meet people where they…

The ASME Section 11 Special Working Group On Plant Life Extension

International Nuclear Information System (INIS)

Katz, L.R.

1990-01-01

The codes and standards applicable to plant life extension have not been identified in the U.S. at this time. However, several initiatives have been taken to establish specific codes and standards pertaining to nuclear plant life extension (PLEX). One of these initiatives, sponsored by ASME, is the Section XI Special Working Group on Plant Life Extension (SWG-PLEX). The SWG-PLEX reports to the ASME Section XI Subcommittee and is responsible for recommending or drafting rules and requirements for modifying Section XI to accommodate age-related degradation to support nuclear plant life extension. This paper summarizes the results and reports the activities of the SWG-PLEX during the 1989/1990 period

Finite element analysis for temperature distributions in a cold forging

International Nuclear Information System (INIS)

Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong; Kim, Sung Wook; Song, In Chul; Jeon, Byung Cheol

2013-01-01

In this research, the finite element method is utilized to predict the temperature distributions in a cold-forging process for a cambolt. The cambolt is mainly used as a part of a suspension system of a vehicle. The cambolt has an off-centered lobe that manipulates the vertical position of the knuckle and wheel to a slight degree. The cambolt requires certain mechanical properties, such as strength and endurance limits. Moreover, temperature is also an important factor to realize mass production and improve efficiency. However, direct measurement of temperature in a forging process is infeasible with existing technology; therefore, there is a critical need for a new technique. Accordingly, in this study, a thermo-coupled finite element method is developed for predicting the temperature distribution. The rate of energy conversion to heat for the workpiece material is determined, and the temperature distribution is analyzed throughout the forging process for a cambolt. The temperatures associated with different punch speeds are also studied, as well as the relationships between load, temperature, and punch speed. Experimental verification of the technique is presented.

Finite element analysis for temperature distributions in a cold forging

Energy Technology Data Exchange (ETDEWEB)

Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong [Chungbuk National University, Cheongju (Korea, Republic of); Kim, Sung Wook [Yanbian National University, Yanbian (China); Song, In Chul; Jeon, Byung Cheol [Sunil dyfas, Jincheon (Korea, Republic of)

2013-10-15

In this research, the finite element method is utilized to predict the temperature distributions in a cold-forging process for a cambolt. The cambolt is mainly used as a part of a suspension system of a vehicle. The cambolt has an off-centered lobe that manipulates the vertical position of the knuckle and wheel to a slight degree. The cambolt requires certain mechanical properties, such as strength and endurance limits. Moreover, temperature is also an important factor to realize mass production and improve efficiency. However, direct measurement of temperature in a forging process is infeasible with existing technology; therefore, there is a critical need for a new technique. Accordingly, in this study, a thermo-coupled finite element method is developed for predicting the temperature distribution. The rate of energy conversion to heat for the workpiece material is determined, and the temperature distribution is analyzed throughout the forging process for a cambolt. The temperatures associated with different punch speeds are also studied, as well as the relationships between load, temperature, and punch speed. Experimental verification of the technique is presented.

Bronchodilatory and anti-inflammatory effects of ASM-024, a nicotinic receptor ligand, developed for the treatment of asthma.

Science.gov (United States)

Assayag, Evelyne Israël; Beaulieu, Marie-Josée; Cormier, Yvon

2014-01-01

Conventional asthma and COPD treatments include the use of bronchodilators, mainly β2-adrenergic agonists, muscarinic receptor antagonists and corticosteroids or leukotriene antagonists as anti-inflammatory agents. These active drugs are administered either separately or given as a fixed-dose combination medication into a single inhaler. ASM-024, a homopiperazinium compound, derived from the structural modification of diphenylmethylpiperazinium (DMPP), has been developed to offer an alternative mechanism of action that could provide symptomatic control through combined anti-inflammatory and bronchodilator properties in a single entity. A dose-dependent inhibition of cellular inflammation in bronchoalveolar lavage fluid was observed in ovalbumin-sensitized mice, subsequently treated for 3 days by nose-only exposure with aerosolized ASM-024 at doses up to 3.8 mg/kg (ED50 = 0.03 mg/kg). The methacholine ED250 values indicated that airway hyperresponsivenness (AHR) to methacholine decreased following ASM-024 administration by inhalation at a dose of 1.5 mg/kg, with a value of 0.145 ± 0.032 mg/kg for ASM 024-treated group as compared to 0.088 ± 0.023 mg/kg for untreated mice. In in vitro isometric studies, ASM-024 elicited dose-dependent relaxation of isolated mouse tracheal, human, and dog bronchial preparations contracted with methacholine and guinea pig tracheas contracted with histamine. ASM-024 showed also a dose and time dependant protective effect on methacholine-induced contraction. Overall, with its combined anti-inflammatory, bronchodilating and bronchoprotective properties, ASM-024 may represent a new class of drugs with a novel pharmacological approach that could prove useful for the chronic maintenance treatment of asthma and, possibly, COPD.

A material based approach to creating wear resistant surfaces for hot forging

Science.gov (United States)

Babu, Sailesh

Tools and dies used in metal forming are characterized by extremely high temperatures at the interface, high local pressures and large metal to metal sliding. These harsh conditions result in accelerated wear of tooling. Lubrication of tools, done to improve metal flow drastically quenches the surface layers of the tools and compounds the tool failure problem. This phenomenon becomes a serious issue when parts forged at complex and are expected to meet tight tolerances. Unpredictable and hence uncontrolled wear and degradation of tooling result in poor part quality and premature tool failure that result in high scrap, shop downtime, poor efficiency and high cost. The objective of this dissertation is to develop a computer-based methodology for analyzing the requirements hot forging tooling to resist wear and plastic deformation and wear and predicting life cycle of forge tooling. Development of such is a system is complicated by the fact that wear and degradation of tooling is influenced by not only the die material used but also numerous process controls like lubricant, dilution ratio, forging temperature, equipment used, tool geometries among others. Phenomenological models available u1 the literature give us a good thumb rule to selecting materials but do not provide a way to evaluate pits performance in field. Once a material is chosen, there are no proven approaches to create surfaces out of these materials. Coating approaches like PVD and CVD cannot generate thick coatings necessary to withstand the conditions under hot forging. Welding cannot generate complex surfaces without several secondary operations like heat treating and machining. If careful procedures are not followed, welds crack and seldom survive forging loads. There is a strong need for an approach to selectively, reliably and precisely deposit material of choice reliably on an existing surface which exhibit not only good tribological properties but also good adhesion to the substrate

Effect of raw materials and hardening process on hardness of manually forged knife

Science.gov (United States)

Balkhaya, Suwarno

2017-06-01

Knives are normally made by forging process either using a machine or traditional method by means of hammering process. This present work was conducted to study the effects of steel raw materials and hardening process on the hardness of manually forged knives. The knife samples were made by traditional hammering (forging) process done by local blacksmith. Afterward, the samples were heat treated with two different hardening procedures, the first was based on the blacksmith procedure and the second was systematically done at the laboratory. The forging was done in the temperature ranged between 900-950°C, while the final temperature ranged between 650-675°C. The results showed that knives made of spring steel and heat treated in simulated condition at the laboratory obtained higher level of hardness, i.e. 62 HRC. In general, knives heat treated by local blacksmith had lower level of hardness that those obtained from simulated condition. Therefore, we concluded that the traditional knife quality in term of hardness can be improved by optimizing the heat treatment schedule.

Fabrication Improvement of Cold Forging Hexagonal Nuts by Computational Analysis and Experiment Verification

Directory of Open Access Journals (Sweden)

Shao-Yi Hsia

2015-01-01

Full Text Available Cold forging has played a critical role in fasteners and has been applied to the automobile industry, construction industry, aerospace industry, and living products so that cold forging presents the opportunities for manufacturing more products. By using computer simulation, this study attempts to analyze the process of creating machine parts, such as hexagonal nuts. The DEFORM-3D forming software is applied to analyze the process at various stages in the computer simulation, and the compression test is also used for the flow stress equation in order to compare the differences between the experimental results and the equation that is built into the computer simulation software. At the same time, the metallography and hardness of experiments are utilized to understand the cold forging characteristics of hexagonal nuts. The research results would benefit machinery businesses to realize the forging load and forming conditions at various stages before the fastener formation. In addition to planning proper die design and production, the quality of the produced hexagonal nuts would be more stable to promote industrial competitiveness.

Influence of the Constitutive Flow Law in FEM Simulation of the Radial Forging Process

Directory of Open Access Journals (Sweden)

Olivier Pantalé

2013-01-01

Full Text Available Radial forging is a widely used forming process for manufacturing hollow products in transport industry. As the deformation of the workpiece, during the process, is a consequence of a large number of high-speed strokes, the Johnson-Cook constitutive law (taking into account the strain rate seems to be well adapted for representing the material behavior even if the process is performed under cold conditions. But numerous contributions concerning radial forging analysis, in the literature, are based on a simple elastic-plastic formulation. As far as we know, this assumption has yet not been validated for the radial forging process. Because of the importance of the flow law in the effectiveness of the model, our purpose in this paper is to analyze the influence of the use of an elastic-viscoplastic formulation instead of an elastic-plastic one for modeling the cold radial forging process. In this paper we have selected two different laws for the simulations: the Johnson-Cook and the Ludwik ones, and we have compared the results in terms of forging force, product's thickness, strains, stresses, and CPU time. For the presented study we use an AISI 4140 steel, and we denote a fairly good agreement between the results obtained using both laws.

21 CFR 211.182 - Equipment cleaning and use log.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Equipment cleaning and use log. 211.182 Section 211.182 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Reports § 211.182 Equipment cleaning and use log. A written record of major equipment cleaning...

Creep-fatigue damage evaluation for SS-316LN (ORNL PLATES): - RCC-MR vs. ASME SEC III - NH

International Nuclear Information System (INIS)

Sati, Bhuwan Chandra; Jalaldeen, S.; Velusamy, K.; Selvaraj, P.

2016-01-01

Investigations of high temperature tests done on ORNL plate with deformation control loading, under creep-fatigue damage have been presented. The test results with methodology of RCC-MR and ASME-NH life prediction under creep-fatigue loading have been assessed. The stress relaxation effect in calculating the life using RCC-MR under creep-fatigue damage is found to be significant in presence of secondary stress. RCC-MR: 2007 is more realistic number of cycles (predicts 51 number of cycles) as compared to ASME-NH (predicts 312 number of cycles) which is demonstrated by the experimental work (observed 86 numbers of cycles). Between RCC-MR and experimental work, design code seems to be more conservative for life prediction due to creep-fatigue damage. For fatigue damage, the approaches are same and the difference comes from material properties and the starting stress for applying Neuber's rule. ASME approach has the limitation of stress range magnitude. ASME approach predicts lower elastic plus plastic strain for the cases having S* above the linear stress limit. For creep strain and creep damage evaluation, ASME and RCC-MR have different approaches for calculating the stress at the beginning and during the hold period. The RCC-MR takes account of cyclic hardening or softening effects (hardening in the present case of 316 LN) by means of the cyclic stress-strain curve and the benefit of symmetrization effects which are significant for this material. The ASME code neglects these effects and instead relies on an approach based on the isochronous stress-strain curves. (author)

21 CFR 182.2122 - Aluminum calcium silicate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Aluminum calcium silicate. 182.2122 Section 182.2122 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....2122 Aluminum calcium silicate. (a) Product. Aluminum calcium silicate. (b) Tolerance. 2 percent. (c...

50 CFR 18.2 - Scope of regulations.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Scope of regulations. 18.2 Section 18.2 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED... with respect to cetacea (whales and porpoises), pinnipedia, other than walrus (seals and sea lions...

A study on technical issues of materials and design bases in ASME section III subsection NH code

International Nuclear Information System (INIS)

Lee, Hyeong Yeon; Kim, Jong Bum; Yoo, Bong

2000-12-01

In this study, an analysis of evaluation report by ORNL on the technical issues of elevated temperatures design guide line, ASME Code Section III Subsection NH was conducted and a brief evaluation procedure of the creep-fatigue damage was presented. ORNL published the report in 1993 and reviewed the issue areas where code rules or regulatory guides may be lacking or inadequate to ensure safe operation over the expected life cycles for liquid metal reactor systems. From historical viewpoint of the ASME NH code development, ASME Code Case 47 was changed much in 1989 edition, which includes the stress relaxation behavior in creep damage evaluation. Afterwards the 1992 version of CC N-47 was upgraded to Subsection NH in 1995 edition, which is the same with that of CC N-47 1992 edition except few material data. This report brings up the technical and regulatory issues that can not guarantee the safe and reliable operation of the ALMR which got the conceptual design certification from NRC. Twenty three technical issues were raised and settlement methodology were proposed. Additionally, the status of items approved by ASME code subgroup of elevated temperature design committee for the revision of the most recent 1998 edition of ASME NH was described

Tailorable Burning Behavior of Ti14 Alloy by Controlling Semi-Solid Forging Temperature.

Science.gov (United States)

Chen, Yongnan; Yang, Wenqing; Zhan, Haifei; Zhang, Fengying; Huo, Yazhou; Zhao, Yongqing; Song, Xuding; Gu, Yuantong

2016-08-16

Semi-solid processing (SSP) is a popular near-net-shape forming technology for metals, while its application is still limited in titanium alloy mainly due to its low formability. Recent works showed that SSP could effectively enhance the formability and mechanical properties of titanium alloys. The processing parameters such as temperature and forging rate/ratio, are directly correlated with the microstructure, which endow the alloy with different chemical and physical properties. Specifically, as a key structural material for the advanced aero-engine, the burn resistant performance is a crucial requirement for the burn resistant titanium alloy. Thus, this work aims to assess the burning behavior of Ti14, a kind of burn resistant alloy, as forged at different semi-solid forging temperatures. The burning characteristics of the alloy are analyzed by a series of burning tests with different burning durations, velocities, and microstructures of burned sample. The results showed that the burning process is highly dependent on the forging temperature, due to the fact that higher temperatures would result in more Ti₂Cu precipitate within grain and along grain boundaries. Such a microstructure hinders the transport of oxygen in the stable burning stage through the formation of a kind of oxygen isolation Cu-enriched layer under the burn product zone. This work suggests that the burning resistance of the alloy can be effectively tuned by controlling the temperature during the semi-solid forging process.

ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

Directory of Open Access Journals (Sweden)

Yongsoon Kim

Full Text Available In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

Science.gov (United States)

Kim, Yongsoon; Sun, Hong

2012-01-01

In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

ASM-3 Acid Sphingomyelinase Functions as a Positive Regulator of the DAF-2/AGE-1 Signaling Pathway and Serves as a Novel Anti-Aging Target

Science.gov (United States)

Kim, Yongsoon; Sun, Hong

2012-01-01

In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals. PMID:23049887

46 CFR 182.450 - Vent pipes for fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Vent pipes for fuel tanks. 182.450 Section 182.450... TONS) MACHINERY INSTALLATION Specific Machinery Requirements § 182.450 Vent pipes for fuel tanks. (a) Each unpressurized fuel tank must be fitted with a vent pipe connected to the highest point of the tank...

On the domestically-made heavy forging for reactor pressure vessels of PWR nuclear power plant

International Nuclear Information System (INIS)

Pan Xiren; Zhang Chen.

1988-01-01

The present situation of the foreign heavy forgings for nuclear reactor pressure vessels and the heavy forgings condition which is used for the Qinshan 300MWe nuclear power plant are described. Some opinions of domestic products is proposed

Abelian Sandpile Model (ASM) and Infinite Volume Limit

Indian Academy of Sciences (India)

ASM- Properties. Any possible sequence of topplings leads to the same stable configuration [Dhar]. The result of particle addition at and subsequent relaxation is given by an operator. £ бвд £ евд £. , where вд £. ¢. ¦. ¤ззз ¤ вг иг . £. ©. ¢ йа£. (Abelian). 7-b ...

21 CFR 182.8892 - α-Tocopherol acetate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true α-Tocopherol acetate. 182.8892 Section 182.8892 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD...-Tocopherol acetate. (a) Product. α-Tocopherol acetate. (b) Conditions of use. This substance is generally...

THE FORMING OF MAGNESIUM ALLOY FORGINGS FOR AIRCRAFT AND AUTOMOTIVE APPLICATIONS

Directory of Open Access Journals (Sweden)

Anna Dziubińska

2016-09-01

Full Text Available The paper presents the theoretical and technological aspects of forming magnesium alloy parts for aircraft and automotive applications. The main applications of magnesium alloys in the aircraft and automotive industries are discussed. In addition, the forging technology for magnesium alloys is generally described, with a particular emphasis on wrought alloys. A brief outline of the state of the art in the forging of magnesium alloys is given based on a survey of the specialist literature and the results of previous research by the authors.

Adapted diffusion processes for effective forging dies

Science.gov (United States)

Paschke, H.; Nienhaus, A.; Brunotte, K.; Petersen, T.; Siegmund, M.; Lippold, L.; Weber, M.; Mejauschek, M.; Landgraf, P.; Braeuer, G.; Behrens, B.-A.; Lampke, T.

2018-05-01

Hot forging is an effective production method producing safety relevant parts with excellent mechanical properties. The economic efficiency directly depends on the occurring wear of the tools, which limits service lifetime. Several approaches of the presenting research group aim at minimizing the wear caused by interacting mechanical and thermal loads by using enhanced nitriding technology. Thus, by modifying the surface zone layer it is possible to create a resistance against thermal softening provoking plastic deformation and pronounced abrasive wear. As a disadvantage, intensely nitrided surfaces may possibly include the risk of increased crack sensitivity and therefore feature the chipping of material at the treated surface. Recent projects (evaluated in several industrial applications) show the high technological potential of adapted treatments: A first approach evaluated localized treatments by preventing areas from nitrogen diffusion with applied pastes or other coverages. Now, further ideas are to use this principle to structure the surface with differently designed patterns generating smaller ductile zones beneath nitrided ones. The selection of suitable designs is subject to certain geo-metrical requirements though. The intention of this approach is to prevent the formation and propagation of cracks under thermal shock conditions. Analytical characterization methods for crack sensitivity of surface zone layers and an accurate system of testing rigs for thermal shock conditions verified the treatment concepts. Additionally, serial forging tests using adapted testing geometries and finally, tests in the industrial production field were performed. Besides stabilizing the service lifetime and decreasing specific wear mechanisms caused by thermal influences, the crack behavior was influenced positively. This leads to a higher efficiency of the industrial production process and enables higher output in forging campaigns of industrial partners.

Manufacturing and material properties of forgings for reactor pressure vessel of high temperature engineering test reactor

International Nuclear Information System (INIS)

Sato, I.; Suzuki, K.

1994-01-01

For the reactor pressure vessel (RPV) of high temperature engineering test reactor (HTTR) which has been developed by Japan Atomic Energy Research Institute (JAERI), 2 1/4Cr-1Mo steel is used first in the world. Material confirmation test has been carried out to demonstrate good applicability of forged low Si 2 1/4Cr-1Mo steel to the RPV of HTTR. Recently, JSW has succeeded in the manufacturing of large size ring forgings and large size forged cover dome integrated with nozzles for stand pipe for the RPV. This paper describes the results of the material confirmation test as well as the manufacturing and material properties of the large forged cover dome integrated with nozzles for stand pipe. (orig.)

High-Temperature Oxidation Behavior and Kinetics of Forged 12Cr-MoVW Steel

Directory of Open Access Journals (Sweden)

Kim Yong Hwan

2017-06-01

Full Text Available The oxidation kinetics of forged 12Cr-MoVW steel was investigated in an air (N2+O2 atmosphere at 873-1073 K (Δ50 K using thermogravimetric analysis. The oxidized samples were characterized using X-ray diffraction, and the surface and cross-sectional morphologies were examined using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The forged 12Cr-MoVW steel samples exhibited parabolic behavior and a low oxidation rate compared with their as-cast counterparts. A protective oxide layer was uniformly formed at relatively low temperature (≤973 K for the forged samples, which thus exhibited better oxidation resistance than the as-cast ones. These oxides are considered solid-solution compounds such as (Fe, Cr2O3.

Forging a unique nursing partnership with China.

Science.gov (United States)

Munn, Flavia

2017-07-12

When members of a London nursing faculty forged a learning partnership with a Chinese counterpart they likely did not expect to be discussing the benefits of using Florence Nightingale lamps to decorate hospital walls. But there is nothing ordinary about the collaboration between King's College London and Nanjing Health School.

46 CFR 53.01-3 - Adoption of section IV of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section IV of the ASME Boiler and Pressure...) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-3 Adoption of section IV of the ASME Boiler and Pressure Vessel Code. (a) Heating boilers shall be designed, constructed, inspected, tested...

Modelling of Damage During Hot Forging of Ingots

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2013-01-01

Ductile damage modelling in the ingot forging process is discussed. Advantages and disadvantages of both coupled and uncoupled ductile damage models are presented. Some uncoupled damage models are examined in greater detail regarding their applicability to different processes, where hydrostatic...

Forged hollows (alloy 617) for PNP-hot gas collectors

International Nuclear Information System (INIS)

Hofmann, F.

1984-01-01

When the partners in the PNP-Project decided to manufacture components, such as gas collectors, from material of type alloy 617, the problem arose that required semi-fabricated products, especially forged hollows weighing several tons each, were not available. As VDM (Vereinigte Deutsche Metallwerke AG) had already experience in production of other semi-fabricated products of this alloy, attempts were made based on this knowledge, to develop manufacturing methods for forged hollows. The aim was to produce hollows as long as possible, and to keep the welding cost minimum. Welded seams are always critical during fabrication, as well as during later inspection under actual operating conditions. The three stage plan used to perform the above task illustrates the development aims is described

Physical Activity Energy Expenditure and Sarcopenia in Black South African Urban Women.

Science.gov (United States)

Kruger, Herculina S; Havemann-Nel, Lize; Ravyse, Chrisna; Moss, Sarah J; Tieland, Michael

2016-03-01

Black women are believed to be genetically less predisposed to age-related sarcopenia. The objective of this study was to investigate lifestyle factors associated with sarcopenia in black South African (SA) urban women. In a cross-sectional study, 247 women (mean age 57 y) were randomly selected. Anthropometric and sociodemographic variables, dietary intakes, and physical activity were measured. Activity was also measured by combined accelerometery/heart rate monitoring (ActiHeart), and HIV status was tested. Dual energy x-ray absorptiometry was used to measure appendicular skeletal mass (ASM). Sarcopenia was defined according to a recently derived SA cutpoint of ASM index (ASM/height squared) decreasing to 8.1% after exclusion of participants who were HIV positive. In multiple regressions with ASM index, grip strength, and gait speed, respectively, as dependent variables, only activity energy expenditure (β = .27) was significantly associated with ASM index. Age (β = -.50) and activity energy expenditure (β = .17) were significantly associated with gait speed. Age (β = -.11) and lean mass (β = .21) were significantly associated with handgrip strength. Sarcopenia was prevalent among these SA women and was associated with low physical activity energy expenditure.

Production of a 304 stainless steel nuclear reactor forging from a very large electroslag refined ingot

International Nuclear Information System (INIS)

Watkins, E.J.; Tihansky, E.L.

1986-01-01

A four-loop, upper barrel flange forging for a nuclear reactor was produced from what the authors believe to be the largest 304H grade stainless steel electroslag refined (ESR) ingot ever refined. The ingot was refined in a 1524-mm-diameter, ingot withdrawal-type ESR furnace using a lime-bearing slag, low-frequency a-c power, and dry air protection. Five electrodes were remelted in order to produce the desired ingot weight. The ingot was subsequently forged in a five-step operation on a 6800-metric-ton press to produce the desired barrel flange configuration. Testing of the finished machined forging revealed excellent tensile ductility, excellent ultrasonic penetrability, and good chemical uniformity with no macrosegregation. Overall quality was judged to be superior to previously produced, conventionally melted forgings

Forging Oxide-Dispersion-Strengthened Superalloys

Science.gov (United States)

Harf, F. H.; Glasgow, T. K.; Moracz, D. J.; Austin, C. M.

1986-01-01

Cladding of mild steel prevents surface cracking when alloy contacts die. Continual need for improvements in properties of alloys capable of withstanding elevated temperatures. Accomplished by using oxide-dispersion-strengthed superalloys such as Inconel Alloy MA 6000. Elevated tensile properties of forged alloy equal those of hot-rolled MA 6000 bar. Stress-rupture properties somewhat lower than those of bar stock but, at 1,100 degrees C, exceed those of strongest commercial single crystal, directionally solidified and conventionally cast superalloys.

46 CFR 52.01-2 - Adoption of section I of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section I of the ASME Boiler and Pressure...) MARINE ENGINEERING POWER BOILERS General Requirements § 52.01-2 Adoption of section I of the ASME Boiler and Pressure Vessel Code. (a) Main power boilers and auxiliary boilers shall be designed, constructed...

Highlight: Forging the new Indonesia-Canada partnership | CRDI ...

International Development Research Centre (IDRC) Digital Library (Canada)

15 avr. 2016 ... Canada's Centre for International Governance Innovation and Indonesia's Centre for Strategic and International Studies organized the Indonesia-Canada Bilateral Forum, Innovation and Change: Forging the New Indonesia-Canada Partnership. IDRC co-sponsored the meeting, held May 26-27, 2015.

Manufacturing involving forging of multiple objects in contact

DEFF Research Database (Denmark)

Nielsen, Chris Valentin; Zhang, W.; Martins, P.A.F.

and dissimilar materials. While being plastically deformed against each other under increasing forging load, the parts dynamically develop their mutual contact interfaces. Comparisons of the final geometry as well as force-displacement curves are evaluated. The potential of simulated applications are discussed...

A Survey of Variable Extragalactic Sources with XTE's All Sky Monitor (ASM)

Science.gov (United States)

Jernigan, Garrett

1998-01-01

The original goal of the project was the near real-time detection of AGN utilizing the SSC 3 of the ASM on XTE which does a deep integration on one 100 square degree region of the sky. While the SSC never performed sufficiently well to allow the success of this goal, the work on the project has led to the development of a new analysis method for coded aperture systems which has now been applied to ASM data for mapping regions near clusters of galaxies such as the Perseus Cluster and the Coma Cluster. Publications are in preparation that describe both the new method and the results from mapping clusters of galaxies.

Phased array inspection of large size forged steel parts

Science.gov (United States)

Dupont-Marillia, Frederic; Jahazi, Mohammad; Belanger, Pierre

2018-04-01

High strength forged steel requires uncompromising quality to warrant advance performance for numerous critical applications. Ultrasonic inspection is commonly used in nondestructive testing to detect cracks and other defects. In steel blocks of relatively small dimensions (at least two directions not exceeding a few centimetres), phased array inspection is a trusted method to generate images of the inside of the blocks and therefore identify and size defects. However, casting of large size forged ingots introduces changes of mechanical parameters such as grain size, the Young's modulus, the Poisson's ratio, and the chemical composition. These heterogeneities affect the wave propagation, and consequently, the reliability of ultrasonic inspection and the imaging capabilities for these blocks. In this context, a custom phased array transducer designed for a 40-ton bainitic forged ingot was investigated. Following a previous study that provided local mechanical parameters for a similar block, two-dimensional simulations were made to compute the optimal transducer parameters including the pitch, width and number of elements. It appeared that depending on the number of elements, backwall reconstruction can generate high amplitude artefacts. Indeed, the large dimensions of the simulated block introduce numerous constructive interferences from backwall reflections which may lead to important artefacts. To increase image quality, the reconstruction algorithm was adapted and promising results were observed and compared with the scattering cone filter method available in the CIVA software.

miR-182 integrates apoptosis, growth, and differentiation programs in glioblastoma.

Science.gov (United States)

Kouri, Fotini M; Hurley, Lisa A; Daniel, Weston L; Day, Emily S; Hua, Youjia; Hao, Liangliang; Peng, Chian-Yu; Merkel, Timothy J; Queisser, Markus A; Ritner, Carissa; Zhang, Hailei; James, C David; Sznajder, Jacob I; Chin, Lynda; Giljohann, David A; Kessler, John A; Peter, Marcus E; Mirkin, Chad A; Stegh, Alexander H

2015-04-01

Glioblastoma multiforme (GBM) is a lethal, therapy-resistant brain cancer consisting of numerous tumor cell subpopulations, including stem-like glioma-initiating cells (GICs), which contribute to tumor recurrence following initial response to therapy. Here, we identified miR-182 as a regulator of apoptosis, growth, and differentiation programs whose expression level is correlated with GBM patient survival. Repression of Bcl2-like12 (Bcl2L12), c-Met, and hypoxia-inducible factor 2α (HIF2A) is of central importance to miR-182 anti-tumor activity, as it results in enhanced therapy susceptibility, decreased GIC sphere size, expansion, and stemness in vitro. To evaluate the tumor-suppressive function of miR-182 in vivo, we synthesized miR-182-based spherical nucleic acids (182-SNAs); i.e., gold nanoparticles covalently functionalized with mature miR-182 duplexes. Intravenously administered 182-SNAs penetrated the blood-brain/blood-tumor barriers (BBB/BTB) in orthotopic GBM xenografts and selectively disseminated throughout extravascular glioma parenchyma, causing reduced tumor burden and increased animal survival. Our results indicate that harnessing the anti-tumor activities of miR-182 via safe and robust delivery of 182-SNAs represents a novel strategy for therapeutic intervention in GBM. © 2015 Kouri et al.; Published by Cold Spring Harbor Laboratory Press.

Assessment of induction elbows for an ASME Code application

International Nuclear Information System (INIS)

Panesar, J.S.; Soliman, M.

1991-01-01

The ASME Nuclear Codes impose some specific requirements on the wall thickness uniformity and the out-of-roundness of cross sections of the elbows for Nuclear Power Plant applications. Due to some of these requirements, manufacturing and installation of these elbows can be time consuming and quite expensive. This paper explores the feasibility of using induction elbows for nuclear application from the stress analysis point of view. To this end, three different sizes of 90deg elbows have been analyzed based on the geometry of an 'ASME Code' elbow and an elbow formed by induction bending. The analysis is carried out for internal pressure, in-plane and out-of-plane loads. Based on the results of these three carbon steel elbows, the use of induction elbows in some of the CANDU-PHW (CANadian Deuterium Uranium-Pressurized Heavy Water) power plant applications seems encouraging. However, before the feasibility can be fully confirmed analysis and induction bending tests over a wider range of geometries, loading conditions, and materials are required. (author)

Suppression or knockout of SaF/SaM overcomes the Sa-mediated hybrid male sterility in rice

Institute of Scientific and Technical Information of China (English)

Yongyao Xie; Baixiao Niu; Yunming Long; Gousi Li; Jintao Tang; Yaling Zhang; Ding Ren; Yao-Guang Liu; Letian Chen

2017-01-01

Hybrids between the indica and japonica subspecies of rice (Oryza sativa) are usually sterile, which hinders utilization of heterosis in the inter-subspecific hybrid breeding. The complex locus Sa comprises two adjacently located genes, SaF and SaM, which interact to cause abortion of pollen grains carrying the japonica allele in japonica-indica hybrids. Here we showed that silencing of SaF or SaM by RNA interference restored male fertility in indica-japonica hybrids with heterozygous Sa. We further used clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9-based genome editing to knockout the SaF and SaM alleles, respectively, of an indica rice line to create hybrid-compatible lines. The resultant artificial neutral alleles did not affect pollen viability and other agricultural traits, but did break down the reproductive barrier in the hybrids. We found that some rice lines have natural neutral allele Sa-n, which was compatible with the typical japonica or indica Sa alleles in hybrids. Our results demonstrate that SaF and SaM are required for hybrid male sterility, but are not essential for pollen development. This study provides effective approaches for the generation of hybrid-compatible lines by knocking out the Sa locus or using the natural Sa-n allele to overcome hybrid male sterility in rice breeding.

Friction and wear in hot forging of steels

International Nuclear Information System (INIS)

Daouben, E.; Dubar, L.; Dubar, M.; Deltombe, R.; Dubois, A.; Truong-Dinh, N.; Lazzarotto, L.

2007-01-01

In the field of hot forging of steels, the mastering of wear phenomena enables to save cost production, especially concerning tools. Surfaces of tools are protected thanks to graphite. The existing lubrication processes are not very well known: amount and quality of lubricant, lubrication techniques have to be strongly optimized to delay wear phenomena occurrence. This optimization is linked with hot forging processes, the lubricant layers must be tested according to representative friction conditions. This paper presents the first part of a global study focused on wear phenomena encountered in hot forging of steels. The goal is the identification of reliable parameters, in order to bring knowledge and models of wear. A prototype testing stand developed in the authors' laboratory is involved in this experimental analysis. This test is called Warm and Hot Upsetting Sliding Test (WHUST). The stand is composed of a heating induction system and a servo-hydraulic system. Workpieces taken from production can be heated until 1200 deg. C. A nitrided contactor representing the tool is heated at 200 deg. C. The contactor is then coated with graphite and rubs against the workpiece, leaving a residual track on it. Friction coefficient and surface parameters on the contactor and the workpiece are the most representative test results. The surface parameters are mainly the sliding length before defects occurrence, and the amplitude of surface profile of the contactor. The developed methodology will be first presented followed by the different parts of the experimental prototype. The results of experiment show clearly different levels of performance according to different lubricants

Utilização de Ecolife® e Acibenzolar-s-metil (ASM no controle da antracnose da banana em pós-colheita Use of Ecolife® and Acibenzolar-S-metil (ASM on the control of antracnosis in banana post-harvest

Directory of Open Access Journals (Sweden)

Luciano Marinho Furtado

2010-09-01

Full Text Available O objetivo deste trabalho foi avaliar a ação dos produtos ASM e Ecolife no controle da antracnose pós-colheita em frutos de banana. Frutos sadios de banana, variedades maçã, prata, pacovan e cacau , em fase intermediária de maturação, foram imersos previamente em soluções de ASM e Ecolife e inoculados com Colletotrichum musae. Utilizou-se o delineamento inteiramente casualizado, em esquema fatorial com quatro repetições. Os resultados apresentados demonstraram a eficácia dos produtos nas concentrações de 5 ml/ L (Ecolife e 0,50g/ L (ASM no controle da antracnose nas variedades analisa das. A variedade cacau apresentou menor lesão quando tratada com o Ecolife (5,79 mm. Com relação ao efeito do ASM, a bana na prata demonstrou um melhor resultado, com tamanho médio de lesão de 5,62 mm. Com o decorrer do processo de maturação dos frutos houve um decréscimo na severidade da doença nas quatro variedades estudadas, exceto no tratamento testemunha, que continuou apresentando aumento no tamanho das lesões nos frutos e atingir a polpa ao final da maturação.The aim of this work was to evaluate the effects of ASM and Ecolife on the control of post-harvest antracnosis in banana. Banana fruits of Maçã, Prata, Pacovan and Figo varieties, at intermediate stage of maturation, were immersed in solutions of ASM and Ecolife and inoculated with Colletotrichum musae A completely randomized design was used, at a factorial scheme 4x2 (four varieties x two products with four replicates. The presented results demonstrated the susceptibility of the fruits to the disease, mainly Maça variety with lesion of 17,99 mm. It was demosntrated the effectiveness of products at concentrations of 5ml. L-1 (Ecolife and 0.50g. L-1 (ASM on antracnosis control. The Figo variety presented the smallest injuries when treated with Ecolife (5.79 mm. Regarding ASM effects, Prata variety demonstrated the best performance, with 5.62 mm of injuries diameter

Superplastic forging nitride ceramics

Science.gov (United States)

Panda, P.C.; Seydel, E.R.; Raj, R.

1988-03-22

A process is disclosed for preparing silicon nitride ceramic parts which are relatively flaw free and which need little or no machining, said process comprising the steps of: (a) preparing a starting powder by wet or dry mixing ingredients comprising by weight from about 70% to about 99% silicon nitride, from about 1% to about 30% of liquid phase forming additive and from 1% to about 7% free silicon; (b) cold pressing to obtain a preform of green density ranging from about 30% to about 75% of theoretical density; (c) sintering at atmospheric pressure in a nitrogen atmosphere at a temperature ranging from about 1,400 C to about 2,200 C to obtain a density which ranges from about 50% to about 100% of theoretical density and which is higher than said preform green density, and (d) press forging workpiece resulting from step (c) by isothermally uniaxially pressing said workpiece in an open die without initial contact between said workpiece and die wall perpendicular to the direction of pressing and so that pressed workpiece does not contact die wall perpendicular to the direction of pressing, to substantially final shape in a nitrogen atmosphere utilizing a temperature within the range of from about 1,400 C to essentially 1,750 C and strain rate within the range of about 10[sup [minus]7] to about 10[sup [minus]1] seconds[sup [minus]1], the temperature and strain rate being such that surface cracks do not occur, said pressing being carried out to obtain a shear deformation greater than 30% whereby superplastic forging is effected.

Technical aspects and manufacturing methods for JT-60SA toroidal field coil casings

International Nuclear Information System (INIS)

Rossi, Paolo; Cucchiaro, A.; Brolatti, G.; Cocilovo, V.; Ginoulhiac, G.; Polli, G.; Gabriele, M.; Di Muzio, F.; Philips, G.; Tomarchio, V.

2014-01-01

Highlights: • A contract between ENEA and Walter Tosto started on July 2012 for the construction of 18 TF coil casings for JT-60SA. • Design and manufacturing of mock-ups representative of straight and curved legs of the casings have been completed. • Final design of the casings has been completed and manufacturing activities have already started and are ongoing. • The completion of the first three casings will be completed within the end of 2013 and the production of all the 18 casings is foreseen by the end of 2015. - Abstract: JT-60SA is a superconducting tokamak machine to be assembled in Naka site, Japan, designed to contribute to the early realization of fusion energy by supporting the exploitation of ITER and research toward DEMO. In the frame of the Broader Approach Agreement a contract between ENEA and Walter Tosto (Chieti, Italy) started on July 2012 for the construction of 18 TF coil casings for JT-60SA. Two different sets of 9 casings each will be progressively delivered, from 2013 to the end of 2015, to ASG Superconductors (Genoa, Italy) and to Alstom (Belfort, France), where the integration of the winding pack into the casing will be carried out. Each TF coil casing (height 7.5 m and width 4.5 m) consists of four main components: one “Straight Leg Outboard” and one “Curved Leg Outboard” both with their own covers, “Straight Leg Inboard” and “Curved Leg Inboard”. The casing components are segmented in forgings and plates made of FM316LNL. The straight leg outboard is composed of two wings welded to a central core and two elbows welded at the ends with a cooling channel installed inside. Elbows of straight leg outboard are segmented in two half-elbows machined from 1 rough forging and welded to the central core made by plate. Welding of wings to the central core is performed in EBW (electron beam welding) and the straight part is welded to the elbows by NGTIG (TIG narrow gap) process. The curved leg outboard is composed of two

Technical aspects and manufacturing methods for JT-60SA toroidal field coil casings

Energy Technology Data Exchange (ETDEWEB)

Rossi, Paolo, E-mail: paolo.rossi@enea.it [ENEA, Via Enrico Fermi 45, 00044 Frascati, Rome (Italy); Cucchiaro, A.; Brolatti, G.; Cocilovo, V.; Ginoulhiac, G.; Polli, G. [ENEA, Via Enrico Fermi 45, 00044 Frascati, Rome (Italy); Gabriele, M.; Di Muzio, F. [Walter Tosto, Via Erasmo Piaggio, 66100 Chieti (Italy); Philips, G.; Tomarchio, V. [JT-60SA European Home Team, Boltzmannstrasse 2, D-85748 Garching (Germany)

2014-10-15

Highlights: • A contract between ENEA and Walter Tosto started on July 2012 for the construction of 18 TF coil casings for JT-60SA. • Design and manufacturing of mock-ups representative of straight and curved legs of the casings have been completed. • Final design of the casings has been completed and manufacturing activities have already started and are ongoing. • The completion of the first three casings will be completed within the end of 2013 and the production of all the 18 casings is foreseen by the end of 2015. - Abstract: JT-60SA is a superconducting tokamak machine to be assembled in Naka site, Japan, designed to contribute to the early realization of fusion energy by supporting the exploitation of ITER and research toward DEMO. In the frame of the Broader Approach Agreement a contract between ENEA and Walter Tosto (Chieti, Italy) started on July 2012 for the construction of 18 TF coil casings for JT-60SA. Two different sets of 9 casings each will be progressively delivered, from 2013 to the end of 2015, to ASG Superconductors (Genoa, Italy) and to Alstom (Belfort, France), where the integration of the winding pack into the casing will be carried out. Each TF coil casing (height 7.5 m and width 4.5 m) consists of four main components: one “Straight Leg Outboard” and one “Curved Leg Outboard” both with their own covers, “Straight Leg Inboard” and “Curved Leg Inboard”. The casing components are segmented in forgings and plates made of FM316LNL. The straight leg outboard is composed of two wings welded to a central core and two elbows welded at the ends with a cooling channel installed inside. Elbows of straight leg outboard are segmented in two half-elbows machined from 1 rough forging and welded to the central core made by plate. Welding of wings to the central core is performed in EBW (electron beam welding) and the straight part is welded to the elbows by NGTIG (TIG narrow gap) process. The curved leg outboard is composed of two

$\\alpha$-decay study of $^{182,184}$Tl

CERN Document Server

Van Beveren, C; Barzakh, A E; Cocolios, T E; de Groote, R P; Fedorov, D; Fedosseev, V N; Ferrer, R; Ghys, L; Huyse, M; Köster, U; Lane, J; Liberati, V; Lynch, K M; Marsh, B A; Molkanov, P L; Procter, T J; Rapisarda, E; Sandhu, K; Seliverstov, M D; Van Duppen, P; Venhart, M; Veselský, M

2016-01-01

α -decay spectroscopy of 182,184 Tl has been performed at the CERN isotope separator on-line ( ISOLDE ) facility. New fi ne-structure α decays have been observed for both isotopes. α -decay branching ratios of 0.089 ( 19 ) %, 0.047 ( 6 ) % and 1.22 ( 30 ) % have been deduced for the ( 10 − ) , ( 7 + ) and ( 2 − ) states respectively in 184 Tl and a lower limit of 0.49% for the α -decay branching ratio of 182 Tl. A new half-life of 9.5 ( 2 ) s for the ( 2 − ) state in 184 Tl and 1.9 ( 1 ) s for the low-spin state in 182 Tl has been deduced. Using α – γ coincidence analysis, multiple γ rays were observed de-exciting levels in 178,18 0 Au fed by 182,184 Tl α decays. The γ transitions connecting these low-lying states in 178,18 0 Au are essential to sort the data and possibly identify bands from in- beam studies in these isotopes. Owing to the complex fi ne-structure α decays and limited knowledge about the structure of the daughter nuclei, only partial level schemes could be constructed for bot...

Estimativa do custo da asma em tratamento ambulatorial especializado em unidade universitária no Sistema Único de Saúde

OpenAIRE

Eduardo Costa de Freitas Silva

2014-01-01

A asma é considerada um problema de saúde pública mundial. É necessário expandir o conhecimento sobre seus custos associados em diferentes regiões. O principal objetivo foi estimar os custos do tratamento da asma em uma população de asmáticos com diferentes níveis de gravidade, sob tratamento ambulatorial especializado. Os objetivos secundários foram analisar as características clínicas e sócio-econômicas da população e o custo incremental da associação com a rinite e infecções respiratórias ...

Suppression or knockout of SaF/SaM overcomes the Sa-mediated hybrid male sterility in rice.

Science.gov (United States)

Xie, Yongyao; Niu, Baixiao; Long, Yunming; Li, Gousi; Tang, Jintao; Zhang, Yaling; Ren, Ding; Liu, Yao-Guang; Chen, Letian

2017-09-01

Hybrids between the indica and japonica subspecies of rice (Oryza sativa) are usually sterile, which hinders utilization of heterosis in the inter-subspecific hybrid breeding. The complex locus Sa comprises two adjacently located genes, SaF and SaM, which interact to cause abortion of pollen grains carrying the japonica allele in japonica-indica hybrids. Here we showed that silencing of SaF or SaM by RNA interference restored male fertility in indica-japonica hybrids with heterozygous Sa. We further used clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9-based genome editing to knockout the SaF and SaM alleles, respectively, of an indica rice line to create hybrid-compatible lines. The resultant artificial neutral alleles did not affect pollen viability and other agricultural traits, but did break down the reproductive barrier in the hybrids. We found that some rice lines have natural neutral allele Sa-n, which was compatible with the typical japonica or indica Sa alleles in hybrids. Our results demonstrate that SaF and SaM are required for hybrid male sterility, but are not essential for pollen development. This study provides effective approaches for the generation of hybrid-compatible lines by knocking out the Sa locus or using the natural Sa-n allele to overcome hybrid male sterility in rice breeding. © 2017 The Authors. Bioelectromagnetics published by Wiley Periodicals, Inc. © 2017 Institute of Botany, Chinese Academy of Sciences.

Production of A356 aluminum alloy wheels by thixo-forging combined with a low superheat casting process

Directory of Open Access Journals (Sweden)

Wang Shuncheng

2013-09-01

Full Text Available The A356 aluminum alloy wheels were produced by thixo-forging combined with a low superheat casting process. The as-cast microstructure, microstructure evolution during reheating and the mechanical properties of thixo-forged wheels made from the A356 aluminum alloy were studied. The results show that the A356 aluminum alloy round billet with fine, uniform and non-dendritic grains can be obtained when the melt is cast at 635 篊. When the round billet is reheated at 600 篊 for 60 min, the non-dendritic grains are changed into spherical ones and the round billet can be easily thixo-forged into wheels. The tensile strength, yield strength and elongation of the thixo-forged wheels with T6 heat treatment are 327.6 MPa, 228.3 MPa and 7.8%, respectively, which are higher than those of a cast wheel. It is suggested that the thixo-forging combined with the low superheat casting process is an effective technique to produce aluminum alloy wheels with high mechanical properties.

strength and ductility of forged 1200 aluminum alloy reinforced

African Journals Online (AJOL)

eobe

duced cylindrical shape samples, which were homogenized at 420 ... and properties of deformed materials depend on other factors ... after the surfaces were ground with emery paper of ... Figure 2: Maximum elongation of forged and annealed.

Qualitative Research of AZ31 Magnesium Alloy Aircraft Brackets Produced by a New Forging Method

Directory of Open Access Journals (Sweden)

Dziubińska A.

2016-06-01

Full Text Available The paper reports a selection of numerical and experimental results of a new closed-die forging method for producing AZ31 magnesium alloy aircraft brackets with one rib. The numerical modelling of the new forming process was performed by the finite element method.The distributions of stresses, strains, temperature and forces were examined. The numerical results confirmed that the forgings produced by the new forming method are correct. For this reason, the new forming process was verified experimentally. The experimental results showed good agreement with the numerical results. The produced forgings of AZ31 magnesium alloy aircraft brackets with one rib were then subjected to qualitative tests.

Recommendations to ASME for code guidelines and criteria for continued operation of equipment

International Nuclear Information System (INIS)

Harvey, J.F.

1993-01-01

In May 1988, the American Society of Mechanical Engineers, ASME, asked the Pressure Vessel Research Council, PVRC, to review the part it should play in the continued operation of equipment originally designed and fabricated to the ASME codes and rules. This was prompted solely by an economic opportunity in which the capital expenditures to replace plants was far more costly than evaluating, repairing, and extending the nominal design life of the individual component. For instance, nuclear plants are normally designed for a life of 40 years, while fossil fired facilities may have been designed for other time lives, yet at the end of their original design life may actually have many useful years remaining. While this action was economically prompted, it inherently involved a two-fold one; namely, (1) safety, (2) legal. There is no question of safety to operating personnel. While codes for fossil components do not specify design lives, their adoption by many states provides a legal means of procedure in event of a mishap. This recognizes a cradle-to-grave safety responsibility. It is toward maintaining ASMEs leadership as a code authority that this report has been prepared

Evaluation of intergranular corrosion rate and microstructure of forged 316L round bar

International Nuclear Information System (INIS)

Lim, H. K.; Kim, Y. S.

2009-01-01

When austenitic stainless steels are heat treated in the range of 500∼850 .deg. C, the alloys are sensitized due to the formation of chromium carbide at grain boundaries and then intergranular corrosion occurs. This paper aims to evaluate the intergranular corrosion rate and microstructural change of forged 316L stainless steel. To analyze the microstructure by forging conditions, ferrite phase, sigma phase, intergranular precipitation were observed. In order to evaluate the intergranular corrosion rate. Huey test was performed by ASTM A262. On the base of microstructural observation, ferrite and sigma phases were not detected, and also intergranular precipitation was not revealed in optical microscopic observation. By ASTM A262 Practice A, step structure was shown in all forging conditions. Intergranular corrosion rate gradually increased by Huey test periods but average corrosion rate was under 0.03 mm/month

Evaluation of intergranular corrosion rate and microstructure of forged 316L round bar

Energy Technology Data Exchange (ETDEWEB)

Lim, H. K.; Kim, Y. S. [Andong National University, Andong (Korea, Republic of)

2009-12-15

When austenitic stainless steels are heat treated in the range of 500{approx}850 .deg. C, the alloys are sensitized due to the formation of chromium carbide at grain boundaries and then intergranular corrosion occurs. This paper aims to evaluate the intergranular corrosion rate and microstructural change of forged 316L stainless steel. To analyze the microstructure by forging conditions, ferrite phase, sigma phase, intergranular precipitation were observed. In order to evaluate the intergranular corrosion rate. Huey test was performed by ASTM A262. On the base of microstructural observation, ferrite and sigma phases were not detected, and also intergranular precipitation was not revealed in optical microscopic observation. By ASTM A262 Practice A, step structure was shown in all forging conditions. Intergranular corrosion rate gradually increased by Huey test periods but average corrosion rate was under 0.03 mm/month.

Numerical simulation of the dynamic recrystallization behaviour in hot precision forging helical gears

Directory of Open Access Journals (Sweden)

Feng Wei

2015-01-01

Full Text Available In hot precision forging helical gears, the dynamic recrystallization phenomena will occur, which affect the microstructure of the formed part and in turn decide their mechanical properties. To investigate the effect of deformation temperature on the dynamic recrystallization in hot precision forging helical gears, a three dimensional (3D finite element (FE model was created by coupling the thermo-mechanical model with the microstructure evolution model developed based on the hot compressive experimental data of 20CrMnTiH steel. The hot precision forging process was simulated and the effect laws of the deformation temperature on the microstructure evolution the formed part were investigated. The results show that the dynamic recrystallization volume fraction and the average grain sizes increased with the increasing deformation temperature and the higher deformation temperature is beneficial to dynamic recrystallization and grain refinement.

The effects of composition and thermal path on hot ductility of forging steels

Science.gov (United States)

Connolly, Brendan M.

This work examines the effects of composition and thermal path on the hot ductility of several forging steels with varied aluminum and nitrogen content. The primary mechanisms and controlling factors related to hot ductility are identified with a focus on the role of precipitates and segregation. The unique thermal paths and solidification structures of large cross-section forging ingots are discussed. Hot ductility testing is performed in a manner that approximates industrial conditions experienced by large cross-section forging ingots. A computer model for precipitation of aluminum nitride and vanadium nitride in austenite is presented. Industrial material is examined for comparison to experimental findings. It is found that increased aluminum and nitrogen content coarsens the as-solidified structure. The combined effects of microsegregation and uphill diffusion during deformation allow for carbide precipitation at prior austenite grain boundaries which reduces the hot ductility.

Numerical simulation and experimental verification of microstructure evolution in large forged pipe used for AP1000 nuclear power plants

International Nuclear Information System (INIS)

Wang, Shenglong; Yang, Bin; Zhang, Mingxian; Wu, Huanchun; Peng, Jintao; Gao, Yang

2016-01-01

Highlights: • Establish systematically the database of 316LN stainless steel for Deform-3D. • Simulate the microstructure evolution during forging of AP1000 primary coolant pipe. • Carry out full-scale forging experiment for verification in engineering practice. • Get desirable grain size in simulation and experiment. • The variation trends of grain sizes in simulation and experiment are consistent. - Abstract: AP1000 primary coolant pipe is a large special-shaped forged pipe made of 316LN stainless steel. Due to the non-uniform temperature and deformation during its forging, coarse and fine grains usually coexist in the forged pipe, resulting in the heterogeneous microstructure and anisotropic performance. To investigate the microstructure evolution during the entire forging process, in the present research, the database of the 316LN stainless steel was established and a numerical simulation was performed. The results indicate that the middle body section of the forged pipe has an extremely uniform average grain size with the value smaller than 30 μm. The grain sizes in the ends of body sections were ranged from 30 μm to 60 μm. Boss sections have relatively homogeneous microstructure with the average grain size 30 μm to 44 μm. Furthermore, a full-scale hot forging was carried out for verification. Comparison of theoretical and experimental results showed good agreement and hence demonstrated the capabilities of the numerical simulation presented here. It is noteworthy that all grains in the workpiece were confirmed less than 180 μm, which meets the designer’s demands.

27 CFR 40.182 - Record of processed tobacco.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Record of processed tobacco. 40.182 Section 40.182 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS...

50 CFR 300.182 - HMS international trade permit.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false HMS international trade permit. 300.182... FISHERIES REGULATIONS International Trade Documentation and Tracking Programs for Highly Migratory Species § 300.182 HMS international trade permit. (a) General. An importer, entering for consumption fish or...

ASM Based Synthesis of Handwritten Arabic Text Pages

Directory of Open Access Journals (Sweden)

Laslo Dinges

2015-01-01

Full Text Available Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

ASM Based Synthesis of Handwritten Arabic Text Pages.

Science.gov (United States)

Dinges, Laslo; Al-Hamadi, Ayoub; Elzobi, Moftah; El-Etriby, Sherif; Ghoneim, Ahmed

2015-01-01

Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs) based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

Aeração nasal em crianças asmáticas Nasal ventilation in asthmatics children

Directory of Open Access Journals (Sweden)

Daniele Andrade da Cunha

2011-10-01

Full Text Available OBJETIVO: identificar a presença de sinais de alterações na expiração de crianças asmáticas. MÉTODO: este estudo foi realizado com 30 crianças com idades entre 6 e 10 anos de ambos os sexos com diagnóstico clínico de asma confirmado pelo prontuário médico e 30 crianças não asmáticas também de ambos os sexos na mesma faixa etária. Foi avaliada a aeração nasal com o espelho milimetrado de Altmann, sendo mensurado o escape de ar nasal objetivando a verificação da saída uni ou bilateral do ar e a relação de simetria entre a narina direita e a esquerda. As imagens foram importadas para o computador por meio do scanner HP da série Scanjet 2400. A análise foi realizada no software Scion Image for Windows (Alpha 4.0.3.2. Para análise das variáveis quantitativas entre grupos foi aplicado o teste t-student e para a análise intragrupos foi aplicado o teste t-Student pareado.Todas as conclusões foram tomadas ao nível de significância de 5%, sendo usados o Excel 2000 e o SPSS v8.0, para as análises. RESULTADOS: não foram encontradas diferenças estatisticamente significantes entre as crianças asmáticas e não-ásmáticas, acerca das mensurações quanto à área total e quanto às áreas das narinas direita e esquerda. CONCLUSÃO: não foi identificada a presença de sinais de alterações na expiração de crianças asmáticas, desta forma, faz-se necessário um estudo mais específico das funções nasal e pulmonar.PURPOSE: to identify the symptoms of changes in the exhalation of asthmatic children. METHOD: this study was conducted with 30 children from 6 to 10 year-old, of both genders and with asthma clinical diagnosis confirmed by medical records and 30 non-asthmatic children from 6 to 10 year-old, of both genders, and with same age. We evaluated the nasal ventilation with Altmann millimeter nasal mirror measuring the nasal air escape in order to check their unilateral or bilateral air output and the relation of

Ultrasonic phased arrays for nondestructive inspection of forgings

International Nuclear Information System (INIS)

Wuestenberg, H.; Rotter, B.; Klanke, H.P.; Harbecke, D.

1993-01-01

Ultrasonic examinations on large forgings like rotor shafts for turbines or components for nuclear reactors are carried out at various manufacturing stages and during in-service inspections. During the manufacture, most of the inspections are carried out manually. Special in-service conditions, such as those at nuclear pressure vessels, have resulted in the development of mechanized scanning equipment. Ultrasonic probes have improved, and well-adapted sound fields and pulse shapes and based on special imaging procedures for the representation of the reportable reflectors have been applied. Since the geometry of many forgings requires the use of a multitude of angles for the inspections in-service and during manufacture, phased-array probes can be used successfully. The main advantages of the phased-array concept, e.g. the generation of a multitude of angles with the typical increase of redundancy in detection and quantitative evaluation and the possibility to produce pictures of defect situations, will be described in this contribution

Towards a consensus-based biokinetic model for green microalgae – The ASM-A

DEFF Research Database (Denmark)

Wágner, Dorottya Sarolta; Valverde Pérez, Borja; Sæbø, Mariann

2016-01-01

developed to predict microalgal growth. However, none of these models can effectively describe all the relevant processes when microalgal growth is coupled with nutrient removal and recovery from wastewaters. Here, we present a mathematical model developed to simulate green microalgal growth (ASM-A) using...... and substrate availability can introduce significant variability on parameter values for predicting the reaction rates for bulk nitrate and the intracellularly stored nitrogen state-variables, thereby requiring scenario specific model calibration. ASM-A was identified using standard cultivation medium...

Geologic setting of the proposed Fallon FORGE Site, Nevada: Suitability for EGS research and development

Science.gov (United States)

Faulds, James E.; Blankenship, Douglas; Hinz, Nicholas H.; Sabin, Andrew; Nordquist, Josh; Hickman, Stephen H.; Glen, Jonathan; Kennedy, Mack; Siler, Drew; Robinson-Tait, Ann; Williams, Colin F.; Drakos, Peter; Calvin, Wendy M.

2015-01-01

The proposed Fallon FORGE site lies within and adjacent to the Naval Air Station Fallon (NASF) directly southeast of the town of Fallon, Nevada, within the large basin of the Carson Sink in west-central Nevada. The site is located on two parcels that include land owned by the NASF and leased and owned by Ormat Nevada, Inc. The Carson Sink in the vicinity of the Fallon site is covered by Quaternary deposits, including alluvial fan, eolian, and lacustrine sediments. Four wells penetrate the entire Neogene section and bottom in Mesozoic basement. Late Miocene to Quaternary basin-fill sediments are 0.5 to >1 km thick and overlie Oligocene-Miocene volcanic and lesser sedimentary rocks. The volcanic section is 0.5 to 1.0 km thick and dominated by Miocene mafic lavas. The Neogene section rests nonconformably on heterogeneous Mesozoic basement, which consists of Triassic-Jurassic metamorphic rocks intruded by Cretaceous granitic plutons. The structural framework is dominated by a gently west-tilted half graben cut by moderately to steeply dipping N- to NNEstriking normal faults that dip both east and west. Quaternary faults have not been observed within the proposed FORGE site. Fallon was selected for a potential FORGE site due to its extensional tectonic setting, abundance of available data, existing infrastructure, and documented temperatures, permeability, and lithologic composition of potential reservoirs that fall within the ranges specified by DOE for FORGE. Since the early 1970s, more than 45 wells have been drilled for geothermal exploration within the area. Four exploration wells within the FORGE site are available for use in the project. Several additional wells are available for monitoring outside the central FORGE site within the NASF and Ormat lease area, including numerous temperature gradient holes. There is an existing, ten-station micro-seismic earthquake (MEQ) array that has been collecting data since 2001; the MEQ array can be expanded to encompass the

Assessment of long-term creep strength of grade 91 steel

Energy Technology Data Exchange (ETDEWEB)

Kimura, Kazuhiro; Sawada, Kota; Kushima, Hideaki [National Inst. for Materials Science, Tsukuba, Ibaraki (Japan)

2010-07-01

In 2004 and 2005 long-term creep rupture strength of ASME Grade 91 type steels of plate, pipe, forging and tube materials was evaluated in Japan by means of region splitting analysis method in consideration of 50% of 0.2% offset yield stress. According to the evaluated 100,000h creep rupture strength of 94MPa for plate, pipe and forging steels and 92MPa for tube steel at 600 C, allowable tensile stress of the steels regulated in the Interpretation for the Technical Standard for Thermal Power Plant was slightly reduced. New creep rupture data of the steels obtained in the long-term indicate further reduction of long-term creep rupture strength. Not only creep rupture strength, but also creep deformation property of the ASME Grade 91 steel was investigated and need of reevaluation of long-term creep strength of Grade 91 steel was indicated. A refinement of region splitting analysis method for creep rupture like prediction was discussed. (orig.)

Numerical modeling of axi-symmetrical cold forging process by ``Pseudo Inverse Approach''

Science.gov (United States)

Halouani, A.; Li, Y. M.; Abbes, B.; Guo, Y. Q.

2011-05-01

The incremental approach is widely used for the forging process modeling, it gives good strain and stress estimation, but it is time consuming. A fast Inverse Approach (IA) has been developed for the axi-symmetric cold forging modeling [1-2]. This approach exploits maximum the knowledge of the final part's shape and the assumptions of proportional loading and simplified tool actions make the IA simulation very fast. The IA is proved very useful for the tool design and optimization because of its rapidity and good strain estimation. However, the assumptions mentioned above cannot provide good stress estimation because of neglecting the loading history. A new approach called "Pseudo Inverse Approach" (PIA) was proposed by Batoz, Guo et al.. [3] for the sheet forming modeling, which keeps the IA's advantages but gives good stress estimation by taking into consideration the loading history. Our aim is to adapt the PIA for the cold forging modeling in this paper. The main developments in PIA are resumed as follows: A few intermediate configurations are generated for the given tools' positions to consider the deformation history; the strain increment is calculated by the inverse method between the previous and actual configurations. An incremental algorithm of the plastic integration is used in PIA instead of the total constitutive law used in the IA. An example is used to show the effectiveness and limitations of the PIA for the cold forging process modeling.

SABP2, a methyl salicylate esterase is required for the systemic acquired resistance induced by acibenzolar-S-methyl in plants.

Science.gov (United States)

Tripathi, Diwaker; Jiang, Yu-Lin; Kumar, Dhirendra

2010-08-04

Tobacco SABP2, a 29kDa protein catalyzes the conversion of methyl salicylic acid (MeSA) into salicylic acid (SA) to induce SAR. Pretreatment of plants with acibenzolar-S-methyl (ASM), a functional analog of salicylic acid induces systemic acquired resistance (SAR). Data presented in this paper suggest that SABP2 catalyzes the conversion of ASM into acibenzolar to induce SAR. Transgenic SABP2-silenced tobacco plants when treated with ASM, fail to express PR-1 proteins and do not induce robust SAR expression. When treated with acibenzolar, full SAR is induced in SABP2-silenced plants. These results show that functional SABP2 is required for ASM-mediated induction of resistance. Copyright (c) 2010 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

Application of adjusted subpixel method (ASM) in HRCT measurements of the bronchi in bronchial asthma patients and healthy individuals.

Science.gov (United States)

Mincewicz, Grzegorz; Rumiński, Jacek; Krzykowski, Grzegorz

2012-02-01

Recently, we described a model system which included corrections of high-resolution computed tomography (HRCT) bronchial measurements based on the adjusted subpixel method (ASM). To verify the clinical application of ASM by comparing bronchial measurements obtained by means of the traditional eye-driven method, subpixel method alone and ASM in a group comprised of bronchial asthma patients and healthy individuals. The study included 30 bronchial asthma patients and the control group comprised of 20 volunteers with no symptoms of asthma. The lowest internal and external diameters of the bronchial cross-sections (ID and ED) and their derivative parameters were determined in HRCT scans using: (1) traditional eye-driven method, (2) subpixel technique, and (3) ASM. In the case of the eye-driven method, lower ID values along with lower bronchial lumen area and its percentage ratio to total bronchial area were basic parameters that differed between asthma patients and healthy controls. In the case of the subpixel method and ASM, both groups were not significantly different in terms of ID. Significant differences were observed in values of ED and total bronchial area with both parameters being significantly higher in asthma patients. Compared to ASM, the eye-driven method overstated the values of ID and ED by about 30% and 10% respectively, while understating bronchial wall thickness by about 18%. Results obtained in this study suggest that the traditional eye-driven method of HRCT-based measurement of bronchial tree components probably overstates the degree of bronchial patency in asthma patients. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Application of adjusted subpixel method (ASM) in HRCT measurements of the bronchi in bronchial asthma patients and healthy individuals

International Nuclear Information System (INIS)

Mincewicz, Grzegorz; Rumiński, Jacek; Krzykowski, Grzegorz

2012-01-01

Background: Recently, we described a model system which included corrections of high-resolution computed tomography (HRCT) bronchial measurements based on the adjusted subpixel method (ASM). Objective: To verify the clinical application of ASM by comparing bronchial measurements obtained by means of the traditional eye-driven method, subpixel method alone and ASM in a group comprised of bronchial asthma patients and healthy individuals. Methods: The study included 30 bronchial asthma patients and the control group comprised of 20 volunteers with no symptoms of asthma. The lowest internal and external diameters of the bronchial cross-sections (ID and ED) and their derivative parameters were determined in HRCT scans using: (1) traditional eye-driven method, (2) subpixel technique, and (3) ASM. Results: In the case of the eye-driven method, lower ID values along with lower bronchial lumen area and its percentage ratio to total bronchial area were basic parameters that differed between asthma patients and healthy controls. In the case of the subpixel method and ASM, both groups were not significantly different in terms of ID. Significant differences were observed in values of ED and total bronchial area with both parameters being significantly higher in asthma patients. Compared to ASM, the eye-driven method overstated the values of ID and ED by about 30% and 10% respectively, while understating bronchial wall thickness by about 18%. Conclusions: Results obtained in this study suggest that the traditional eye-driven method of HRCT-based measurement of bronchial tree components probably overstates the degree of bronchial patency in asthma patients.

Feature extraction for face recognition via Active Shape Model (ASM) and Active Appearance Model (AAM)

Science.gov (United States)

Iqtait, M.; Mohamad, F. S.; Mamat, M.

2018-03-01

Biometric is a pattern recognition system which is used for automatic recognition of persons based on characteristics and features of an individual. Face recognition with high recognition rate is still a challenging task and usually accomplished in three phases consisting of face detection, feature extraction, and expression classification. Precise and strong location of trait point is a complicated and difficult issue in face recognition. Cootes proposed a Multi Resolution Active Shape Models (ASM) algorithm, which could extract specified shape accurately and efficiently. Furthermore, as the improvement of ASM, Active Appearance Models algorithm (AAM) is proposed to extracts both shape and texture of specified object simultaneously. In this paper we give more details about the two algorithms and give the results of experiments, testing their performance on one dataset of faces. We found that the ASM is faster and gains more accurate trait point location than the AAM, but the AAM gains a better match to the texture.

Stainless steel forgings for nuclear chemical plants

International Nuclear Information System (INIS)

1982-02-01

This Specification covers detailed requirements for the supply of austenitic stainless steel forgings used in radioactive and corrosive areas within the Nuclear Industry. With the exception of 316S51 the materials specified are all suitable for contact with nitric acid, 316S51 being included as suitable for use in contact with sodium and other alkali metals at elevated temperatures. (author)

The Investigations of Friction under Die Surface Vibration in Cold Forging Process

DEFF Research Database (Denmark)

Jinming, Sha

investigation, and the second stage is to design and manufacture a more practical tool system which can be used to forging some industrial components with larger capacity. The high performance and power piezoelectric actuator stack as the vibration source will be used for designing the vibration system in order...... to 50% with vibration being applied in forming process. Furthermore, by using finite element method, a series of the simulations of the cold forging process under die surface excitation have been implemented in order to further understand the influence of vibration on friction, especially the influence...

Performance Assessment Method for a Forged Fingerprint Detection Algorithm

Science.gov (United States)

Shin, Yong Nyuo; Jun, In-Kyung; Kim, Hyun; Shin, Woochang

The threat of invasion of privacy and of the illegal appropriation of information both increase with the expansion of the biometrics service environment to open systems. However, while certificates or smart cards can easily be cancelled and reissued if found to be missing, there is no way to recover the unique biometric information of an individual following a security breach. With the recognition that this threat factor may disrupt the large-scale civil service operations approaching implementation, such as electronic ID cards and e-Government systems, many agencies and vendors around the world continue to develop forged fingerprint detection technology, but no objective performance assessment method has, to date, been reported. Therefore, in this paper, we propose a methodology designed to evaluate the objective performance of the forged fingerprint detection technology that is currently attracting a great deal of attention.

Plane strain forging of a niobium micro-alloyed steel

International Nuclear Information System (INIS)

Balancin, O.; Ferran L, G.; Rio de Janeiro Univ.

1984-01-01

Various termomechanical treatments were carried out on a niobium micro-alloyed steel and a low carbon steel as reference material, using an apparatus for hot phane strain forging. Control of processing variables and the presence of niobium strongly modify the austenite microstructure, which upon decomposition produces various phases such as polygonal and acicular ferrite and martensite, alone or together in variable proportions. Corresponding to this diversity of structures there is a wide variation in mechanical properties at room temperature: the initial yield point varies from 310 to 650 MPa and the reduction of area in uniaxial tension from 82 to 57% for the niobium steel. These results show that hot forging a niobium micro-alloyed steel may be a suitable manufacturing process for satisfying a wide range of specifications in a final product with low equivalent carbon. (Author) [pt

Design of a forging processing route for a gas turbine compressor disc in IMI 834

International Nuclear Information System (INIS)

Clark, G.S.

1993-01-01

The microstructure in all parts of a modern gas turbine compressor disc must be carefully controlled to give the optimum balance for resistance to creep and fatigue. This is particularly true for advanced titanium alloys such as IMI834. Dynamic recrystallisation during high temperature deformation and static recrystallisation and grain growth during heat treatment, all have a profound effect on the grain structure of the disc. These processes are affected by temperature, rate of deformation and various microstructural features. These may include the size and volume fraction of primary alpha particles and current beta grain size. The construction of a computer model to simulate the forging process must therefore take all these factors into account to fully simulate the mechanical and microstructural behaviour of the material during processing. This requires a complete characterisation of the material to formulate mechanical and microstructural constitutive equations for use in a visco-plastic finite element forging model. Similarly the forging equipment must be fully characterised so that forging processes can be accurately simulated. (orig.)

Near-liquidus forging, partial remelting and thixoforging of an AZ91D + Y magnesium alloy

International Nuclear Information System (INIS)

Zhao Zude; Chen Qiang; Hu Chuankai; Huang Shuhai; Wang Yuanqing

2009-01-01

A new route, near-liquidus forging plus partial remelting, has been developed for obtaining globular microstructures. Firstly, a material is formed by near-liquidus forging for obtaining a fine dendritic microstructure. Globular microstructure can be produced by reheating the material into the semi-solid temperature range for a period of time. In this paper, an AZ91D alloy with the addition of yttrium was prepared by near-liquidus forging. Microstructure evolution during partial remelting was studied at temperatures and for times. Tensile mechanical properties of thixoforged components were also determined. It is shown that the fine dendritic structure firstly evolves into a blocky structure during partial remelting. With prolonged holding time, the blocky structure disintegrates into polygonal solid particles. Prolonging time and increasing temperature promote a faster spheroidization. Good mechanical properties are obtained for the thixoforged AZ91D alloy with the addition of yttrium prepared by near-liquidus forging, with a yield strength of 160.9 MPa and a ultimate tensile strength of 301.7 MPa and a elongation to fracture of 9.734%.

3D automatic anatomy segmentation based on iterative graph-cut-ASM.

Science.gov (United States)

Chen, Xinjian; Bagci, Ulas

2011-08-01

This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al. [Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 degrees and 0.03, and over all foot bones are about 3.5709 mm, 0.35 degrees and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and all foot bones for

3D automatic anatomy segmentation based on iterative graph-cut-ASM

International Nuclear Information System (INIS)

Chen, Xinjian; Bagci, Ulas

2011-01-01

Purpose: This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. Methods: The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al.[Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. Results: The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 deg. and 0.03, and over all foot bones are about 3.5709 mm, 0.35 deg. and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and

Internal Shear Forging Processes for Missile Primary Structures.

Science.gov (United States)

1981-07-20

Growth in Shear Forming," Trans. ASME, J. Eng. ind., Vol. 90, 1968, pp. 63-70. 1 28. H. J. Dreikandt, "Untersuchung Uber das DrUckwalzen zylindrisher...10 US Army Missile Command ATTN: DRSMI-RLM Redstone Arsenal, AL 35809 Comma nder 12 US Army Missile Command + camera-ready master ATTN: DRDMI- EAT

Low appendicular skeletal muscle mass (ASM) with limited mobility and poor health outcomes in middle-aged African Americans.

Science.gov (United States)

Malmstrom, Theodore K; Miller, Douglas K; Herning, Margaret M; Morley, John E

2013-09-01

Recent efforts to provide a consensus definition propose that sarcopenia be considered a clinical syndrome associated with the loss of both skeletal muscle mass and muscle function that occurs with aging. Validation of sarcopenia definitions that include both low muscle mass and poor muscle function is needed. In the population-based African American Health (AAH) study (N = 998 at baseline/wave 1), muscle mass and mobility were evaluated in a clinical testing center in a subsample of N = 319 persons (ages 52-68) at wave 4 (2004). Muscle mass was measured using dual energy x-ray absorptiometry and mobility by a 6-min walk test and 4-m gait walk test. Height corrected appendicular skeletal mass (ASM; 9.0 ± 1.5 in n = 124 males, 8.3 ± 2.2 in n = 195 females) was computed as total lean muscle mass in arms and legs (kilograms) divided by the square of height (meters). Cross-sectional and longitudinal (6-year) associations of low ASM (bottom 25 % AAH sample; ASM with limited mobility (4-m gait walk ≤1 m/s or 6-min walk ASM with limited mobility was associated with IADL difficulties (p = .008) and frailty (p = .040) but not with ADL difficulties or falls in cross-sectional analyses; and with ADL difficulties (p = .022), IADL difficulties (p = .006), frailty (p = .039), and mortality (p = .003) but not with falls in longitudinal analyses adjusted for age and gender. Low ASM alone was marginally associated with mortality (p = .085) but not with other outcomes in cross-sectional or longitudinal analyses. Low ASM with limited mobility is associated with poor health outcomes among late middle-aged African Americans.

A novel anti-inflammatory drug, SDZ ASM 981, for the treatment of skin diseases: in vitro pharmacology.

Science.gov (United States)

Grassberger, M; Baumruker, T; Enz, A; Hiestand, P; Hultsch, T; Kalthoff, F; Schuler, W; Schulz, M; Werner, F J; Winiski, A; Wolff, B; Zenke, G

1999-08-01

SDZ ASM 981, a novel ascomycin macrolactam derivative, has high anti-inflammatory activity in animal models of allergic contact dermatitis and shows clinical efficacy in atopic dermatitis, allergic contact dermatitis and psoriasis, after topical application. Here we report on the in vitro activities of this promising new drug. SDZ ASM 981 inhibits the proliferation of human T cells after antigen-specific or non-specific stimulation. It downregulates the production of Th1 [interleukin (IL)-2, interferon-gamma] and Th2 (IL-4, IL-10) type cytokines after antigen-specific stimulation of a human T-helper cell clone isolated from the skin of an atopic dermatitis patient. SDZ ASM 981 inhibits the phorbol myristate acetate/phytohaemagglutinin-stimulated transcription of a reporter gene coupled to the human IL-2 promoter in the human T-cell line Jurkat and the IgE/antigen-mediated transcription of a reporter gene coupled to the human tumour necrosis factor (TNF)-alpha promoter in the murine mast-cell line CPII. It does not, however, affect the human TNF-alpha promoter controlled transcription of a reporter gene in a murine dendritic cell line (DC18 RGA) after stimulation via the FcgammaRIII receptor. SDZ ASM 981 also prevents the release of preformed pro-inflammatory mediators from mast cells, as shown in the murine cell line CPII after stimulation with IgE/antigen. In summary, these results demonstrate that SDZ ASM 981 is a specific inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro.

Comparative evaluation of structural integrity for ITER blanket shield block based on SDC-IC and ASME code

Energy Technology Data Exchange (ETDEWEB)

Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Ha, Min-Su, E-mail: msha12@nfri.re.kr [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Sa-Woong; Jung, Hun-Chea [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Duck-Hoi [ITER Organization, Route de Vinon sur Verdon - CS 90046, 13067 Sant Paul Lez Durance (France)

2016-11-01

Highlights: • The procedure of structural integrity and fatigue assessment was described. • Case studies were performed according to both SDC-IC and ASME Sec. • III codes The conservatism of the ASME code was demonstrated. • The study only covers the specifically comparable case about fatigue usage factor. - Abstract: The ITER blanket Shield Block is a bulk structure to absorb radiation and to provide thermal shielding to vacuum vessel and external vessel components, therefore the most significant load for Shield Block is the thermal load. In the previous study, the thermo-mechanical analysis has been performed under the inductive operation as representative loading condition. And the fatigue evaluations were conducted to assure structural integrity for Shield Block according to Structural Design Criteria for In-vessel Components (SDC-IC) which provided by ITER Organization (IO) based on the code of RCC-MR. Generally, ASME code (especially, B&PV Sec. III) is widely applied for design of nuclear components, and is usually well known as more conservative than other specific codes. For the view point of the fatigue assessment, ASME code is very conservative compared with SDC-IC in terms of the reflected K{sub e} factor, design fatigue curve and other factors. Therefore, an accurate fatigue assessment comparison is needed to measure of conservatism. The purpose of this study is to provide the fatigue usage comparison resulting from the specified operating conditions shall be evaluated for Shield Block based on both SDC-IC and ASME code, and to discuss the conservatism of the results.

Comparative evaluation of structural integrity for ITER blanket shield block based on SDC-IC and ASME code

International Nuclear Information System (INIS)

Shim, Hee-Jin; Ha, Min-Su; Kim, Sa-Woong; Jung, Hun-Chea; Kim, Duck-Hoi

2016-01-01

Highlights: • The procedure of structural integrity and fatigue assessment was described. • Case studies were performed according to both SDC-IC and ASME Sec. • III codes The conservatism of the ASME code was demonstrated. • The study only covers the specifically comparable case about fatigue usage factor. - Abstract: The ITER blanket Shield Block is a bulk structure to absorb radiation and to provide thermal shielding to vacuum vessel and external vessel components, therefore the most significant load for Shield Block is the thermal load. In the previous study, the thermo-mechanical analysis has been performed under the inductive operation as representative loading condition. And the fatigue evaluations were conducted to assure structural integrity for Shield Block according to Structural Design Criteria for In-vessel Components (SDC-IC) which provided by ITER Organization (IO) based on the code of RCC-MR. Generally, ASME code (especially, B&PV Sec. III) is widely applied for design of nuclear components, and is usually well known as more conservative than other specific codes. For the view point of the fatigue assessment, ASME code is very conservative compared with SDC-IC in terms of the reflected K_e factor, design fatigue curve and other factors. Therefore, an accurate fatigue assessment comparison is needed to measure of conservatism. The purpose of this study is to provide the fatigue usage comparison resulting from the specified operating conditions shall be evaluated for Shield Block based on both SDC-IC and ASME code, and to discuss the conservatism of the results.

Void consolidation during open-die forging for ultralarge rotor shafts. (1. Formulation of void-closing behavior)

International Nuclear Information System (INIS)

Ono, Shin-ichi; Minami, Katsuyuki; Ochiai, Tomoyuki; Iwadate, Tadao; Nakata, Shin-ichi.

1995-01-01

Open-die forging experiments using different die geometries under hot isothermal conditions and three-dimensional simulations using rigid-plastic finite-element method were performed to formulate a void-closing behavior using only two factors; the integral of hydrostatic stress and the equivalent strain. First, upsetting, side-upsetting and V-shape die cogging of several cylinders with a spherical void at the center are carried out and the information on the void volume reduction is obtained. Seconds, the same forgings, but without voids is treated numerically and the development of stress and strain at the location of voids is investigated. Then, by combining these results, and using regression analysis, it is found that the void volume reduction is expressed as a polynomial function of the two factors. When the polynomial function is used, various forging methods can be evaluated quantitatively in terms of void-closing behavior. Therefore it is beneficial to optimize the forging process for a large rotor shaft. (author)

ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

International Nuclear Information System (INIS)

Stillo, Andrew; Ricketts, Craig I.

2013-01-01

High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

Energy Technology Data Exchange (ETDEWEB)

Stillo, Andrew [Camfil Farr, 1 North Corporate Drive, Riverdale, NJ 07457 (United States); Ricketts, Craig I. [New Mexico State University, Department of Engineering Technology and Surveying Engineering, P.O. Box 30001 MSC 3566, Las Cruces, NM 88003-8001 (United States)

2013-07-01

High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

Effect of Forging Parameters on Low Cycle Fatigue Behaviour of Al/Basalt Short Fiber Metal Matrix Composites

Directory of Open Access Journals (Sweden)

R. Karthigeyan

2013-01-01

Full Text Available This paper deals with metal matrix composites (MMCs of Al 7075 alloy containing different weight percentage (2.5, 5, 7.5, and 10 basalt short fiber reinforcement and unreinforced matrix alloy. The samples were produced by the permanent stir casting technique. The casting ingots were cut into blanks to be forged in single stage and double stage, using MN press and graphite-based lubricant. The microstructures and fatigue properties of the matrix alloy and MMC samples were investigated in the as cast state and in the single and double stage forging operations. The microstructure results showed that the forged sample had a uniform distribution of the basalt short fiber throughout the specimens. Evaluation of the fatigue properties showed that the forged samples had higher values than those of the as cast counterparts. After forging, the enhancement of the fatigue strength of the matrix alloy was so significant and high in the case of 2.5 and 5.0 wt. percentage basalt short fiber reinforced MMC, and there was no enhancement in 7.5 and 10 weight percentages short fiber reinforced MMCs. The fracture damage was mainly due to decohesion at the matrix-fiber interface.

Effect of forging parameters on low cycle fatigue behaviour of Al/basalt short fiber metal matrix composites.

Science.gov (United States)

Karthigeyan, R; Ranganath, G

2013-01-01

This paper deals with metal matrix composites (MMCs) of Al 7075 alloy containing different weight percentage (2.5, 5, 7.5, and 10) basalt short fiber reinforcement and unreinforced matrix alloy. The samples were produced by the permanent stir casting technique. The casting ingots were cut into blanks to be forged in single stage and double stage, using MN press and graphite-based lubricant. The microstructures and fatigue properties of the matrix alloy and MMC samples were investigated in the as cast state and in the single and double stage forging operations. The microstructure results showed that the forged sample had a uniform distribution of the basalt short fiber throughout the specimens. Evaluation of the fatigue properties showed that the forged samples had higher values than those of the as cast counterparts. After forging, the enhancement of the fatigue strength of the matrix alloy was so significant and high in the case of 2.5 and 5.0 wt. percentage basalt short fiber reinforced MMC, and there was no enhancement in 7.5 and 10 weight percentages short fiber reinforced MMCs. The fracture damage was mainly due to decohesion at the matrix-fiber interface.

A Simple Model to Identify Risk of Sarcopenia and Physical Disability in HIV-Infected Patients.

Science.gov (United States)

Farinatti, Paulo; Paes, Lorena; Harris, Elizabeth A; Lopes, Gabriella O; Borges, Juliana P

2017-09-01

Farinatti, P, Paes, L, Harris, EA, Lopes, GO, and Borges, JP. A simple model to identify risk of sarcopenia and physical disability in HIV-infected patients. J Strength Cond Res 31(9): 2542-2551, 2017-Early detection of sarcopenia might help preventing muscle loss and disability in HIV-infected patients. This study proposed a model for estimating appendicular skeletal muscle mass (ASM) to calculate indices to identify "sarcopenia" (SA) and "risk for disability due to sarcopenia" (RSA) in patients with HIV. An equation to estimate ASM was developed in 56 patients (47.2 ± 6.9 years), with a cross-validation sample of 24 patients (48.1 ± 6.6 years). The model validity was determined by calculating, in both samples: (a) Concordance between actual vs. estimated ASM; (b) Correlations between actual/estimated ASM vs. peak torque (PT) and total work (TW) during isokinetic knee extension/flexion; (c) Agreement of patients classified with SA and RSA. The predictive equation was ASM (kg) = 7.77 (sex; F = 0/M = 1) + 0.26 (arm circumference; cm) + 0.38 (thigh circumference; cm) + 0.03 (Body Mass Index; kg·m) - 8.94 (R = 0.74; Radj = 0.72; SEE = 3.13 kg). Agreement between actual vs. estimated ASM was confirmed in validation (t = 0.081/p = 0.94; R = 0.86/p < 0.0001) and cross-validation (t = 0.12/p = 0.92; R = 0.87/p < 0.0001) samples. Regression characteristics in cross-validation sample (Radj = 0.80; SEE = 3.65) and PRESS (RPRESS = 0.69; SEEPRESS = 3.35) were compatible with the original model. Percent agreements for the classification of SA and RSA from indices calculated using actual and estimated ASM were of 87.5% and 77.2% (gamma correlations 0.72-1.0; p < 0.04) in validation, and 95.8% and 75.0% (gamma correlations 0.98-0.97; p < 0.001) in cross-validation sample, respectively. Correlations between actual/estimated ASM vs. PT (range 0.50-0.73, p ≤ 0.05) and TW (range 0.59-0.74, p ≤ 0.05) were similar in both samples. In conclusion, our model correctly estimated ASM

Evolution of A-Type Macrosegregation in Large Size Steel Ingot After Multistep Forging and Heat Treatment

Science.gov (United States)

Loucif, Abdelhalim; Ben Fredj, Emna; Harris, Nathan; Shahriari, Davood; Jahazi, Mohammad; Lapierre-Boire, Louis-Philippe

2018-06-01

A-type macrosegregation refers to the channel chemical heterogeneities that can be formed during solidification in large size steel ingots. In this research, a combination of experiment and simulation was used to study the influence of open die forging parameters on the evolution of A-type macrosegregation patterns during a multistep forging of a 40 metric ton (MT) cast, high-strength steel ingot. Macrosegregation patterns were determined experimentally by macroetch along the longitudinal axis of the forged and heat-treated ingot. Mass spectroscopy, on more than 900 samples, was used to determine the chemical composition map of the entire longitudinal sectioned surface. FORGE NxT 1.1 finite element modeling code was used to predict the effect of forging sequences on the morphology evolution of A-type macrosegregation patterns. For this purpose, grain flow variables were defined and implemented in a large scale finite element modeling code to describe oriented grains and A-type segregation patterns. Examination of the A-type macrosegregation showed four to five parallel continuous channels located nearly symmetrical to the axis of the forged ingot. In some regions, the A-type patterns became curved or obtained a wavy form in contrast to their straight shape in the as-cast state. Mass spectrometry analysis of the main alloying elements (C, Mn, Ni, Cr, Mo, Cu, P, and S) revealed that carbon, manganese, and chromium were the most segregated alloying elements in A-type macrosegregation patterns. The observed differences were analyzed using thermodynamic calculations, which indicated that changes in the chemical composition of the liquid metal can affect the primary solidification mode and the segregation intensity of the alloying elements. Finite element modeling simulation results showed very good agreement with the experimental observations, thereby allowing for the quantification of the influence of temperature and deformation on the evolution of the shape of the

Analysis of hot rolling and hot forging effects on mechanical properties and microstructure of ZrNbMoGe alloy

International Nuclear Information System (INIS)

AH Ismoyo; Parikin; Bandriyana

2014-01-01

Research on formation technique by a combined method of rolling and forging has been carried out in order to improve the mechanical properties of ZrNbMoGe alloy to be used as fuel cladding in NPP (Nuclear Power Plant) application. The effects of rolling and forging were analyzed several tests. The tests were conducted for zirconium alloy specimen with a composition of (in % wt.) 97% Zr, 0,5% Mo, 2% Nb and 0,5% Ge, where the specimen was melted with an arc-furnace. The hot rolling and forging were conducted at 900 °C and 950 °C respectively. Hardness test was carried out by using a microhardness testing machine, while microstructure examination and crystal structure analysis were conducted with an optical microscope and an X-ray diffractometer. The results show that the hardness of the alloy increase from 141.21 HV (starting material) to 210.47 HV (hot rolled material) and 365.75 HV (hot forged material). Texturing phenomenon is clearly figured on the microstructure due to hot rolling and forging process. Analysis by diffractogram also indicates that the hot rolling and forging process has influence on the crystal orientation of dominant preferred direction in the reflection plane of (10ī1), recorded from the rise of intensity counting from about 2500 to 3000. In summary, hot forging and rolling process can change the mechanical properties (hardness and texture) and microstructure of materials. (author)

ASME Evaluation on Grid Mobile E-Commerce Process

OpenAIRE

Dan Chang; Wei Liao

2012-01-01

With the development of E-commerce, more scholars have paid attention to research on Mobile E-commerce and mostly focus on the optimization and evaluation of existing process. This paper researches the evaluation of Mobile E-commerce process with a method called ASME. Based on combing and analyzing current mobile business process and utilizing the grid management theory, mobile business process based on grid are constructed. Firstly, the existing process, namely Non-grid Mobile E-commerce, an...

The FORGE (Fate Of Repository Gases) pan European project

International Nuclear Information System (INIS)

Shaw, Richard

2010-01-01

Document available in extended abstract form only. Full text of publication follows: The multiple barrier concept is the cornerstone of all proposed schemes for underground disposal of radioactive wastes. The concept invokes a series of barriers, both engineered and natural, between the waste and the surface. Achieving this concept is the primary objective of all disposal programmes, from site appraisal and characterisation to repository design and construction. However, the performance of the repository as a whole (waste, buffer, engineering disturbed zone, host rock), and in particular its gas transport properties, are still poorly understood. Issues still to be adequately examined that relate to understanding basic processes include: dilational versus visco-capillary flow mechanisms; long-term integrity of seals, in particular gas flow along contacts; role of the EDZ as a conduit for preferential flow; laboratory to field up-scaling. Understanding gas generation and migration is thus vital in the quantitative assessment of repositories and is the focus of the research in this proposal for an integrated, multidisciplinary project. The FORGE project is a pan-European project with links to international radioactive waste management organisations, regulators and academia, specifically designed to tackle the key research issues associated with the generation and movement of repository gasses with partners from 24 organisations in 12 European countries. It is supported by funding under the European Commission FP7 Euratom programme and runs from 2009 to 2013. Of particular importance are the long-term performance of bentonite buffers, plastic clays, indurated mud-rocks and crystalline formations. Further experimental data are required to reduce uncertainty relating to the quantitative treatment of gas in performance assessment. FORGE will address these issues through a series of laboratory and field-scale experiments, including the development of new methods for up

76 FR 52313 - Heavy Forged Hand Tools (i.e., Axes & Adzes, Bars & Wedges, Hammers & Sledges, and Picks...

Science.gov (United States)

2011-08-22

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-803] Heavy Forged Hand Tools (i.e... Administration, Department of Commerce. SUMMARY: As a result of the determinations by the Department of Commerce... on heavy forged hand tools (i.e., [[Page 52314

Shape optimization of metal forming and forging products using the stress equivalent static loads calculated from a virtual model

International Nuclear Information System (INIS)

Jang, Hwan Hak; Jeong, Seong Beom; Park, Gyung Jin

2012-01-01

A shape optimization is proposed to obtain the desired final shape of forming and forging products in the manufacturing process. The final shape of a forming product depends on the shape parameters of the initial blank shape. The final shape of a forging product depends on the shape parameters of the billet shape. Shape optimization can be used to determine the shape of the blank and billet to obtain the appropriate final forming and forging products. The equivalent static loads method for non linear static response structural optimization (ESLSO) is used to perform metal forming and forging optimization since nonlinear dynamic analysis is required. Stress equivalent static loads (stress ESLs) are newly defined using a virtual model by redefining the value of the material properties. The examples in this paper show that optimization using the stress ESLs is quite useful and the final shapes of a forming and forging products are identical to the desired shapes

Family Health and Financial Literacy--Forging the Connection

Science.gov (United States)

Braun, Bonnie; Kim, Jinhee; Anderson, Elaine A.

2009-01-01

Families are at-risk of or experiencing a diminished quality of living and life in current economic times and difficult decisions are required. Health and financial literacy are the basis for wise personal and public decision making. Family and consumer sciences (FCS) professionals can forge connections between health and financial literacy to…

Forge, Arquillian, Swarm and Spring Boot: All play and no effort makes Simon a productive boy

CERN Multimedia

CERN. Geneva

2017-01-01

During this live coding session, Simon will shine some light on a range productivity tools that make software development a pleasure rather than a chore. Simon will live code 2 applications; a Java EE application, with JBoss Forge which uses JPA, Bean Validation, REST and Angular. We’ll test this application using Arquillian from within JBoss Forge. We’ll also show how a Java EE microservice can be developed in Forge and run using JBoss Swarm. The second application will be developed on Spring Boot and using JRebel we’ll rapidly develop and run a Spring application. Attendees will learn how to write code productively using tools designed for developers.

Optimization of the Hot Forging Processing Parameters for Powder Metallurgy Fe-Cu-C Connecting Rods Based on Finite Element Simulation

Science.gov (United States)

Li, Fengxian; Yi, Jianhong; Eckert, Jürgen

2017-12-01

Powder forged connecting rods have the problem of non-uniform density distributions because of their complex geometric shape. The densification behaviors of powder metallurgy (PM) connecting rod preforms during hot forging processes play a significant role in optimizing the connecting rod quality. The deformation behaviors of a connecting rod preform, a Fe-3Cu-0.5C (wt pct) alloy compacted and sintered by the powder metallurgy route (PM Fe-Cu-C), were investigated using the finite element method, while damage and friction behaviors of the material were considered in the complicated forging process. The calculated results agree well with the experimental results. The relationship between the processing parameters of hot forging and the relative density of the connecting rod was revealed. The results showed that the relative density of the hot forged connecting rod at the central shank changed significantly compared with the relative density at the big end and at the small end. Moreover, the relative density of the connecting rod was sensitive to the processing parameters such as the forging velocity and the initial density of the preform. The optimum forging processing parameters were determined and presented by using an orthogonal design method. This work suggests that the processing parameters can be optimized to prepare a connecting rod with uniform density distribution and can help to better meet the requirements of the connecting rod industry.

Statistical analysis of geomagnetic field intensity differences between ASM and VFM instruments onboard Swarm constellation

Science.gov (United States)

De Michelis, Paola; Tozzi, Roberta; Consolini, Giuseppe

2017-02-01

From the very first measurements made by the magnetometers onboard Swarm satellites launched by European Space Agency (ESA) in late 2013, it emerged a discrepancy between scalar and vector measurements. An accurate analysis of this phenomenon brought to build an empirical model of the disturbance, highly correlated with the Sun incidence angle, and to correct vector data accordingly. The empirical model adopted by ESA results in a significant decrease in the amplitude of the disturbance affecting VFM measurements so greatly improving the vector magnetic data quality. This study is focused on the characterization of the difference between magnetic field intensity measured by the absolute scalar magnetometer (ASM) and that reconstructed using the vector field magnetometer (VFM) installed on Swarm constellation. Applying empirical mode decomposition method, we find the intrinsic mode functions (IMFs) associated with ASM-VFM total intensity differences obtained with data both uncorrected and corrected for the disturbance correlated with the Sun incidence angle. Surprisingly, no differences are found in the nature of the IMFs embedded in the analyzed signals, being these IMFs characterized by the same dominant periodicities before and after correction. The effect of correction manifests in the decrease in the energy associated with some IMFs contributing to corrected data. Some IMFs identified by analyzing the ASM-VFM intensity discrepancy are characterized by the same dominant periodicities of those obtained by analyzing the temperature fluctuations of the VFM electronic unit. Thus, the disturbance correlated with the Sun incidence angle could be still present in the corrected magnetic data. Furthermore, the ASM-VFM total intensity difference and the VFM electronic unit temperature display a maximal shared information with a time delay that depends on local time. Taken together, these findings may help to relate the features of the observed VFM-ASM total intensity

Simulation of municipal-industrial full scale WWTP in an arid climate by application of ASM3

Directory of Open Access Journals (Sweden)

Abdelsalam Elawwad

2017-03-01

Full Text Available In developing countries, and due to the high cost of treatment of industrial wastewater, municipal wastewater treatment facilities usually receive a mixture of municipal wastewater and partially treated industrial wastewater. As a result, an increased potential for shock loads with high pollutant concentrations is expected. The use of mathematical modelling of wastewater treatment is highly efficient in such cases. A dynamic model based on activated sludge model no. 3 (ASM3 describing the performance of the activated sludge process at a full scale wastewater treatment plant (WWTP receiving mixed domestic–industrial wastewater located in an arid area is presented. ASM3 was extended by adding the Arrhenius equation to respond to changes in temperature. BioWin software V.4 was used as the model platform. The model was calibrated under steady-state conditions, adjusting only three kinetic and stoichiometric parameters: maximum heterotrophic growth rate (μH = 8 d−1, heterotrophic aerobic decay rate (bH, O2 = 0.18 d−1, and aerobic heterotrophic yield (YH,O2 = 0.4 (gCOD/gCOD. ASM3 was successful in predicting the WWTP performance, as the model was validated with 10 months of routine daily measurements. ASM3 extended with the Arrhenius equation could be helpful in the design and operation of WWTPs with mixed municipal–industrial influent in arid areas.

A two-step superplastic forging forming of semi-continuously cast AZ70 magnesium alloy

Directory of Open Access Journals (Sweden)

Pan Wang

2015-03-01

Full Text Available A two-step technology combined forging with superplastic forming has been developed to enhance the forgeability of semi-continuously cast AZ70 magnesium alloy and realize the application of the as-cast magnesium alloy in large deformation bullet shell. In the first step, fine-grained microstructure preforms that are suitable for superplastic forming were obtained by reasonably designing the size of the initial blanks with the specific height-to-diameter ratio, upsetting the blanks and subsequent annealing. In the second step, the heat treated preforms were forged into the end products at the superplastic conditions. The end products exhibit high quality surface and satisfied microstructure. Consequently, this forming technology that not only avoids complicating the material preparation but also utilizes higher strain rate superplastic provides a near net-shaped novel method on magnesium forging forming technology using as-cast billet.

Forming of Hollow Shaft Forging From Titanium Alloy Ti6Al4V by Means of Rotary Compression

Directory of Open Access Journals (Sweden)

Tomczak J.

2015-04-01

Full Text Available This paper presents chosen results of theoretical-experimental works concerning forming of hollow shafts forgings from titanium alloys, which are applied in aviation industry. At the first stage of conducted analysis, the forging forming process was modeled by means of finite element method. Calculations were made using software Simufact Forming. On the basis of performed simulations optimal parameters of rotary compression process were determined. Next, experimental tests of forging forming in laboratory conditions were made. For the research needs, a forging aggregate, designed by the Authors, was used. Conducted research works confirmed the possibility of metal forming (by means of rotary compression of hollow shafts from hard workable titanium alloys. Numerous advantages of rotary compression process, make it attractive both for low series production (aircraft industry and for mass production (automotive industry.

Methylation Status of miR-182 Promoter in Lung Cancer Cell Lines

Directory of Open Access Journals (Sweden)

Yongwen LI

2015-05-01

Full Text Available Background and objective It has been proven that the abnormal expression of miR-182 was related to the occurrence and development of tumors. The aim of this study is to explore the relationship between the methylation of miR-182 promoter and its expression in lung cancer cell lines. Methods Real-time quantitative PCR and methylation-specific PCR were used to detect the expression level of miR-182 and its promoter methylation status in five lung cancer cell lines (A549, L9981, NL9980, 95C and 95D. DNA sequencing was used to confirm the methylation results. Results The level of miR-182 expression significantly differs among these lung cancer cell lines. The highly metastatic human lung cancer cell lines, namely, A549 and L9981, demonstrate a relatively lower expression level of miR-182 compared with the lowly metastatic human lung cancer cell line 95C. Methylation-specific PCR and DNA sequencing assay results indicate that these lung cancer cell lines present different levels of miR-182 promoter methylation, and the highest methylation level is observed in A549 cells. Furthermore, the expression of miR-182 in these cell lines significantly increases when treated with 10 μM 5’-Aza-dC. Conclusion DNA methylation occurs in the miR-182 promoter region in lung cancer cell lines. This methylation can regulate the expression level of miR-182. Further study must be conducted to explore the function of miR-182 promoter methylation in lung cancer occurrence and development.

Spectrum of SMPD1 mutations in Asian-Indian patients with acid sphingomyelinase (ASM)-deficient Niemann-Pick disease.

Science.gov (United States)

Ranganath, Prajnya; Matta, Divya; Bhavani, Gandham SriLakshmi; Wangnekar, Savita; Jain, Jamal Mohammed Nurul; Verma, Ishwar C; Kabra, Madhulika; Puri, Ratna Dua; Danda, Sumita; Gupta, Neerja; Girisha, Katta M; Sankar, Vaikom H; Patil, Siddaramappa J; Ramadevi, Akella Radha; Bhat, Meenakshi; Gowrishankar, Kalpana; Mandal, Kausik; Aggarwal, Shagun; Tamhankar, Parag Mohan; Tilak, Preetha; Phadke, Shubha R; Dalal, Ashwin

2016-10-01

Acid sphingomyelinase (ASM)-deficient Niemann-Pick disease is an autosomal recessive lysosomal storage disorder caused by biallelic mutations in the SMPD1 gene. To date, around 185 mutations have been reported in patients with ASM-deficient NPD world-wide, but the mutation spectrum of this disease in India has not yet been reported. The aim of this study was to ascertain the mutation profile in Indian patients with ASM-deficient NPD. We sequenced SMPD1 in 60 unrelated families affected with ASM-deficient NPD. A total of 45 distinct pathogenic sequence variants were found, of which 14 were known and 31 were novel. The variants included 30 missense, 4 nonsense, and 9 frameshift (7 single base deletions and 2 single base insertions) mutations, 1 indel, and 1 intronic duplication. The pathogenicity of the novel mutations was inferred with the help of the mutation prediction software MutationTaster, SIFT, Polyphen-2, PROVEAN, and HANSA. The effects of the identified sequence variants on the protein structure were studied using the structure modeled with the help of the SWISS-MODEL workspace program. The p. (Arg542*) (c.1624C>T) mutation was the most commonly identified mutation, found in 22% (26 out of 120) of the alleles tested, but haplotype analysis for this mutation did not identify a founder effect for the Indian population. To the best of our knowledge, this is the largest study on mutation analysis of patients with ASM-deficient Niemann-Pick disease reported in literature and also the first study on the SMPD1 gene mutation spectrum in India. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Comparison of ASME pressure–temperature limits on the fracture probability for a pressurized water reactor pressure vessel

International Nuclear Information System (INIS)

Chou, Hsoung-Wei; Huang, Chin-Cheng

2017-01-01

Highlights: • P-T limits based on ASME K_I_a curve, K_I_C curve and RI method are presented. • Probabilistic and deterministic methods are used to evaluate P-T limits on RPV. • The feasibility of substituting P-T curves with more operational is demonstrated. • Warm-prestressing effect is critical in determining the fracture probability. - Abstract: The ASME Code Section XI-Appendix G defines the normal reactor startup (heat-up) and shut-down (cool-down) operation limits according to the fracture toughness requirement of reactor pressure vessel (RPV) materials. This paper investigates the effects of different pressure-temperature limit operations on structural integrity of a Taiwan domestic pressurized water reactor (PWR) pressure vessel. Three kinds of pressure-temperature limits based on different fracture toughness requirements – the K_I_a fracture toughness curve of ASME Section XI-Appendix G before 1998 editions, the K_I_C fracture toughness curve of ASME Section XI-Appendix G after 2001 editions, and the risk-informed revision method supplemented in ASME Section XI-Appendix G after 2013 editions, respectively, are established as the loading conditions. A series of probabilistic fracture mechanics analyses for the RPV are conducted employing ORNL’s FAVOR code considering various radiation embrittlement levels under these pressure-temperature limit conditions. It is found that the pressure-temperature operation limits which provide more operational flexibility may lead to higher fracture risks to the RPV. The cladding-induced shallow surface breaking flaws are the most critical and dominate the fracture probability of the RPV under pressure-temperature limit transients. Present study provides a risk-informed reference for the operation safety and regulation viewpoint of PWRs in Taiwan.

Interpretation, with respect to ASME code Case N-318, of limit moment and fatigue tests of lugs welded to pipe

International Nuclear Information System (INIS)

Foster, D.C.; Van Duyne, D.A.; Budlong, L.A.; Muffett, J.W.; Wais, E.A.; Streck, G.; Rodabaugh, E.C.

1990-01-01

Two nonmandatory ASME code cases have been used often in the evaluation of lugs on nuclear-power- plant piping systems. ASME Code Case N-318 provides guidance for evaluation of the design of rectangular cross-section attachments on Class 2 or 3 piping, and ASME Code Case N-122 provides guidance for evaluation of lugs on Class 1 piping. These code cases have been reviewed and evaluated based on available test data. The results indicate that the Code cases are overly conservative. Recommendations for revisions to the cases are presented which, if adopted, will reduce the overconservatism

Yrast four-quasi-particle states in 182W

International Nuclear Information System (INIS)

Regan, P.H.; Walker, P.M.; Dracoulis, G.D.; Anderssen, S.S.; Byrne, A.P.; Davidson, P.M.; Kibedi, T.; Lane, G.J.; Stuchbery, A.E.; Yeung, K.C.

1994-01-01

High-spin states of the stable isotope 182 W have been studied using the reactions 176 Yb( 13 C,α3n) 182 W and 176 Yb( 9 Be,3n) 182 W at beam energies of 65 and 40 MeV, respectively. Three, possibly four, new intrinsic states at high spins have been observed corresponding to different high-K four-quasi-particle structures. The K π =15 + and 17 - levels have lifetimes of 78(15) and 25(10) ns, respectively. Rotational bands are observed built on the K π =16 + and 17 - yrast states. The coupling of Nilsson orbitals which give rise to high-K states at the yrast line and the K-forbiddenness of the K π =15 + isomeric decay are discussed. (orig.)

Review of the margins for ASME code fatigue design curve - effects of surface roughness and material variability

International Nuclear Information System (INIS)

Chopra, O. K.; Shack, W. J.

2003-01-01

The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. The Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Existing fatigue strain-vs.-life ((var e psilon)-N) data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of pressure vessel and piping steels. This report provides an overview of the existing fatigue (var e psilon)-N data for carbon and low-alloy steels and wrought and cast austenitic SSs to define the effects of key material, loading, and environmental parameters on the fatigue lives of the steels. Experimental data are presented on the effects of surface roughness on the fatigue life of these steels in air and LWR environments. Statistical models are presented for estimating the fatigue (var e psilon)-N curves as a function of the material, loading, and environmental parameters. Two methods for incorporating environmental effects into the ASME Code fatigue evaluations are discussed. Data available in the literature have been reviewed to evaluate the conservatism in the existing ASME Code fatigue evaluations. A critical review of the margins for ASME Code fatigue design curves is presented

Review of the margins for ASME code fatigue design curve - effects of surface roughness and material variability.

Energy Technology Data Exchange (ETDEWEB)

Chopra, O. K.; Shack, W. J.; Energy Technology

2003-10-03

The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. The Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Existing fatigue strain-vs.-life ({var_epsilon}-N) data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of pressure vessel and piping steels. This report provides an overview of the existing fatigue {var_epsilon}-N data for carbon and low-alloy steels and wrought and cast austenitic SSs to define the effects of key material, loading, and environmental parameters on the fatigue lives of the steels. Experimental data are presented on the effects of surface roughness on the fatigue life of these steels in air and LWR environments. Statistical models are presented for estimating the fatigue {var_epsilon}-N curves as a function of the material, loading, and environmental parameters. Two methods for incorporating environmental effects into the ASME Code fatigue evaluations are discussed. Data available in the literature have been reviewed to evaluate the conservatism in the existing ASME Code fatigue evaluations. A critical review of the margins for ASME Code fatigue design curves is presented.

Development of forging technology for PWR primary piping

International Nuclear Information System (INIS)

Morin, F.; Badeau, J.P.; Lambs, R.

1996-01-01

The purpose of this presentation is to give information on the changes in the design and manufacture of Primary Piping for electronuclear boilers of the Pressurized Water Reactor type (PWR) which has resulted in the making of one-piece forged lines including stub pipes and arcs. The optimization of these items is aimed at improving the life of the new power stations as well as guaranteeing their safety, while reducing inspection and maintenance requirements in service. The demonstration of the manufacturing feasibility has just been completed. It has taken material form in the installation, on the CIVAUX 1 section, of the first one-piece cold leg in the world. It will shortly be followed by the installation on the CIVAUX 2 section of a complete loop of bent forged pipes. Therefore, this new know-how is going to be incorporated in the French Rules (RCC-M) and can be directly taken into consideration both in the next work to be done and in the design and definition of a future nuclear reactor

21 CFR 182.10 - Spices and other natural seasonings and flavorings.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Spices and other natural seasonings and flavorings. 182.10 Section 182.10 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Provisions § 182.10 Spices and other natural seasonings and flavorings. Spices and other natural seasonings...

Numerical optimization of die geometry in open die forging

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2013-01-01

This paper deals with numerical optimization of open die forging of large metallic ingots made by casting implying risk of defects, e.g. central pores. Different material hardening properties and die geometries are combined in order to investigate, which geometry gives rise to maximum closure...

The effect of strain distribution on microstructural developments during forging in a newly developed nickel base superalloy

Energy Technology Data Exchange (ETDEWEB)

Buckingham, R.C. [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom); Argyrakis, C.; Hardy, M.C. [Rolls-Royce plc, PO Box 31, Derby DE24 8BJ (United Kingdom); Birosca, S., E-mail: 522042@swansea.ac.uk [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom)

2016-01-27

In the current study, the effect of strain distribution in a simple forging geometry on the propensity for recrystallization, and its impact on mechanical properties has been investigated in a newly developed experimental nickel-based superalloy. The new alloy was produced via a Powder Metallurgy (PM) route and was subsequently Hot Isostatic Processed (HIP), isothermally forged, and heat treated to produce a coarse grain microstructure with average grain size of 23–32 μm. The alloy was examined by means of Electron Back-Scatter Diffraction (EBSD) to characterise the microstructural features such as grain orientation and morphology, grain boundary characteristics and the identification of potential Prior Particle Boundaries (PPBs) throughout each stage of the processing route. Results at the central region of the cross-section plane parallel to the loading direction showed significant microstructural differences across the forging depth. This microstructural variation was found to be highly dependent on the value of local strain imparted during forging such that areas of low effective strain showed partial recrystallisation and a necklace grain structure was observed following heat treatment. Meanwhile, a fully recrystallised microstructure with no PPBs was observed in the areas of high strain values, in the central region of the forging.

182Hf-182W age dating of a 26Al-poor inclusion and implications for the origin of short-lived radioisotopes in the early Solar System.

Science.gov (United States)

Holst, Jesper C; Olsen, Mia B; Paton, Chad; Nagashima, Kazuhide; Schiller, Martin; Wielandt, Daniel; Larsen, Kirsten K; Connelly, James N; Jørgensen, Jes K; Krot, Alexander N; Nordlund, Ake; Bizzarro, Martin

2013-05-28

Refractory inclusions [calcium-aluminum-rich inclusions, (CAIs)] represent the oldest Solar System solids and provide information regarding the formation of the Sun and its protoplanetary disk. CAIs contain evidence of now extinct short-lived radioisotopes (e.g., (26)Al, (41)Ca, and (182)Hf) synthesized in one or multiple stars and added to the protosolar molecular cloud before or during its collapse. Understanding how and when short-lived radioisotopes were added to the Solar System is necessary to assess their validity as chronometers and constrain the birthplace of the Sun. Whereas most CAIs formed with the canonical abundance of (26)Al corresponding to (26)Al/(27)Al of ∼5 × 10(-5), rare CAIs with fractionation and unidentified nuclear isotope effects (FUN CAIs) record nucleosynthetic isotopic heterogeneity and (26)Al/(27)Al of Solar System, including the origin of short-lived radioisotopes. However, their chronology is unknown. Using the (182)Hf-(182)W chronometer, we show that a FUN CAI recording a condensation origin from a solar gas formed coevally with canonical CAIs, but with (26)Al/(27)Al of ∼3 × 10(-6). The decoupling between (182)Hf and (26)Al requires distinct stellar origins: steady-state galactic stellar nucleosynthesis for (182)Hf and late-stage contamination of the protosolar molecular cloud by a massive star(s) for (26)Al. Admixing of stellar-derived (26)Al to the protoplanetary disk occurred during the epoch of CAI formation and, therefore, the (26)Al-(26)Mg systematics of CAIs cannot be used to define their formation interval. In contrast, our results support (182)Hf homogeneity and chronological significance of the (182)Hf-(182)W clock.

77 FR 39997 - Heavy Forged Hand Tools, Finished or Unfinished, With or Without Handles From the People's...

Science.gov (United States)

2012-07-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-803] Heavy Forged Hand Tools...) (Diamond Sawblades), the Department is notifying the public that the final judgment in this case is not in... review on heavy forged hand tools, finished or unfinished, with or without handles from the People's...

Flujo espiratorio máximo en niños asmáticos: Casos y controles

Directory of Open Access Journals (Sweden)

Arturo Recabarren Lozada

1995-04-01

Full Text Available Con el fin de determinar las variaciones del Flujo Espiratorio Máximo (PEF, se estudiaron a 38 niños asmáticos (CASOS en período intercrítico de la enfermedad y a 38 niños sanos (CONTROLES, de ambos sexos comprendidos entre los 5 y 15 años de edad. Los niños asmáticos fueron clasificados por parámetros clínicos en determinado grado de severidad de asma bronquial, determinando el PEF de cada niño objeto de estudio conel mini-Wright Peak Flow Meter, en 2 registros diarios a los 06 y 18 horas, durante 7 días consecutivos, obteniendo la variabilidad del mismo. Se encuentra diferencia en la variabilidad global de niños asmáticos de todos los grados de severidad de la enfermedad comprada con la de los niños normales, con diferencia estadística altamente significativa (p<0.000001. Las variaciones diurnas del PEF ayuda en el diagnóstico del asma bronquial y también son útiles para realizar la catalogación de severidad de la enfermedad. El PEF correlaciona bien con los síntomas presentados por los pacientes y por lo tanto guarda correspondencia con la Hiperreactividad bronquial (HRB del niño asmático. Postulamos que un niño con historia clínica sugestiva, una variabilidad global mayor del 8% indica que el diagnóstico de asma es altamente probable (Rev Med Hered 1995; 6: 76-82

Standard specification for titanium and titanium alloy forgings

International Nuclear Information System (INIS)

Anon.

1975-01-01

Standards are given for the purchase, manufacture, product testing and certification, packaging, and marketing of annealed Ti and Ti-alloy forgings. The specifications apply to the following Ti alloys: 6Al-Ti-4V, 5Al-Ti-2.5 Sn, and Ti + Pd. Acceptable values for the chemical requirements, product analysis limits, and tensile requirements are tabulated

2 CFR 182.100 - How is this part written?

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false How is this part written? 182.100 Section 182.100 Grants and Agreements OFFICE OF MANAGEMENT AND BUDGET GOVERNMENTWIDE GUIDANCE FOR GRANTS AND AGREEMENTS Reserved GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Purpose and...

What history reveals about Forge River pollution on Long Island, New York's south shore.

Science.gov (United States)

Swanson, R Lawrence; Brownawell, B; Wilson, Robert E; O'Connell, Christine

2010-06-01

Fifty years ago, the Forge River and Moriches Bay, of Long Island's south shore lagoonal system, achieved notoriety when their polluted conditions were alluded to in a report of the US President's Science Advisory Committee (1965). The Woods Hole Oceanographic Institution investigated the bay throughout the 1950s, identifying duck farming as the cause of "objectionable", "highly contaminated" conditions of these waters. Much has changed: duck farming declined; the river was dredged to remove polluted sediments, improve navigation; and barrier island inlets stabilized. Yet, the river remains seasonally eutrophic. Why? This paper reviews what occurred in the Forge River watershed. While governments aggressively curtailed the impacts of duck pollution, they failed to manage development and sewage pollution. The Forge experience indicates that watershed management is a continuing governmental responsibility as development accelerates. Otherwise, we will always be looking for that instantaneous remediation that is usually not affordable and is socially contentious.

Open die forging of large shafts with porosity defects – physical and numerical modelling

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2013-01-01

The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V-shaped d......The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V......-shaped dies with 90o and 120o and a reference pair of flat parallel platens. Holes drilled through the center of these preforms are produced to mimic centerline porosity in full scale cast ingots and intermediate rotation of the preforms replicate a multi-stage forging sequence under laboratory testing...

Multi-objective optimization of die geometry in ingot forging

DEFF Research Database (Denmark)

Christiansen, Peter; Martins, Paulo A.F.; Bay, Niels

2014-01-01

The soundness of an ingot after hot forging with different V-shaped lower dies is evaluated using finite element simulations.Two different modelling approaches that make use of uncoupled ductile damage and coupled ductile damage based on porousplasticity are employed. It is shown that the two...

Crack growth rates in thick materials of alloy 600 and weld metals of alloy 182 in laboratory primary water comparison with field Experience

Energy Technology Data Exchange (ETDEWEB)

Vaillant, F.; Moulart, P.; Boursier, J.M. [Electricite de France (EDF), 75 - Paris (France). Region d' Equipement; Amzallag, C. [Electricite de France (EDF), DIS/SEPTEN, 75 - Paris (France); Daret, J. [CEA Saclay, Dept. de Physico-Chimie DPC/SCCME, 91 - Gif sur Yvette (France)

2002-07-01

Since 1991, when a first leakage occurred on the vessel head of Bugey 3 RPV, an important investigation program was undertaken in laboratory in order to assess crack growth rates (CGRs) of vessel head penetrations (VHPs) in alloy 600 and weld metal in alloy 182 in primary environments. SCC (stress corrosion cracking) tests were performed between 290 C and 360 C on pre-cracked specimens under static loading. Alloy 600: On VHPs with YS{sub 20} ranging from 300 MPa to 468 MPa, it was found that the upper bound for CGRs were dependant on (K(T initial)-K(iscc)){sup 0.3}, in accordance with field experience. In laboratory condition, the activation energy was 130 {+-} 20 kJ/mol, the yield stress increased significantly CGRs but some coupling effects were noted with the microstructure. Cold work increased slightly CGRs on a VHP with initial YS = 468 MPa. Additional tests were performed at 290 C and 325 C on rolled bars, rolled plates and forged plates representative of the other components in alloy 600 of the primary circuit: products with low YS and high GBC had low sensitivity to SCC but it could be significantly increased with cold work raising at the level of 468 MPa, the highest YS investigated on VHPs. Stress relief treatment did not significantly modify SCC resistance. On ten products from the various components, the measured CGRs were strongly correlated to the material susceptibility index for SCC initiation. Alloy 182: Some comparisons were performed in laboratory, with different orientations. Similar trends to alloy 600 were found for the influences of K and temperature on CGRs. 10% cold work increased and stress relief treatment decreased CGRs by a factor 2. CGRs of cracks propagating in the direction of dendrites were 2 to 5 times higher than for cracks propagating in the perpendicular direction. For both alloys 600 and 182, a model is proposed to account for the effects of the main parameters on CGRs and the relevance to field experience is discussed

Crack growth rates in thick materials of alloy 600 and weld metals of alloy 182 in laboratory primary water comparison with field Experience

International Nuclear Information System (INIS)

Vaillant, F.; Moulart, P.; Boursier, J.M.; Daret, J.

2002-01-01

Since 1991, when a first leakage occurred on the vessel head of Bugey 3 RPV, an important investigation program was undertaken in laboratory in order to assess crack growth rates (CGRs) of vessel head penetrations (VHPs) in alloy 600 and weld metal in alloy 182 in primary environments. SCC (stress corrosion cracking) tests were performed between 290 C and 360 C on pre-cracked specimens under static loading. Alloy 600: On VHPs with YS 20 ranging from 300 MPa to 468 MPa, it was found that the upper bound for CGRs were dependant on (K(T initial)-K(iscc)) 0.3 , in accordance with field experience. In laboratory condition, the activation energy was 130 ± 20 kJ/mol, the yield stress increased significantly CGRs but some coupling effects were noted with the microstructure. Cold work increased slightly CGRs on a VHP with initial YS = 468 MPa. Additional tests were performed at 290 C and 325 C on rolled bars, rolled plates and forged plates representative of the other components in alloy 600 of the primary circuit: products with low YS and high GBC had low sensitivity to SCC but it could be significantly increased with cold work raising at the level of 468 MPa, the highest YS investigated on VHPs. Stress relief treatment did not significantly modify SCC resistance. On ten products from the various components, the measured CGRs were strongly correlated to the material susceptibility index for SCC initiation. Alloy 182: Some comparisons were performed in laboratory, with different orientations. Similar trends to alloy 600 were found for the influences of K and temperature on CGRs. 10% cold work increased and stress relief treatment decreased CGRs by a factor 2. CGRs of cracks propagating in the direction of dendrites were 2 to 5 times higher than for cracks propagating in the perpendicular direction. For both alloys 600 and 182, a model is proposed to account for the effects of the main parameters on CGRs and the relevance to field experience is discussed. (authors)

Statistical re-evaluation of the ASME KIC and KIR fracture toughness reference curves

International Nuclear Information System (INIS)

Wallin, K.

1999-01-01

Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the 'master curve', has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original database was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound master curve has the same inherent degree of safety as originally intended for the K IC -reference curve. Similarly, the 1% lower bound master curve corresponds to the K IR -reference curve. (orig.)

Statistical re-evaluation of the ASME KIC and KIR fracture toughness reference curves

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.

1998-01-01

Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the 'Master curve', has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the Master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original data base was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound Master curve has the same inherent degree of safety as originally intended for the K IC -reference curve. Similarly, the 1% lower bound Master curve corresponds to the K IR -reference curve. (orig.)

Summary of design of nuclear vessels and piping to ASME III (NB, NC, ND) and vessels to BS 5500

International Nuclear Information System (INIS)

Harrop, L.P.

1992-01-01

There is a hierarchy of design code requirements for pressurised components, starting with non-nuclear codes as the minimum and progressing through the ASME III nuclear Classes 3, 2, 1. In establishing and assessing the safety justifications of nuclear plants it is important to have an appreciation of the gradation of requirements in the ASME III design rules and how these go beyond non-nuclear component design rules. There are two broad aspects to the structural integrity of pressurised components, namely the achievement of integrity and the demonstration of integrity. The technical requirements of design codes are associated with achieving integrity while the documentary aspects are usually associated with demonstrating integrity. In practice documents also have a part in achieving integrity in the communication of information between different organisations and personnel involved in the design process. It is not possible to assign simple numerical measures to the relative integrity afforded by non-nuclear codes and the three Classes of ASME III. Instead it is necessary to compare the different requirements of the rules for the various technical and documentary aspects. This paper summarises the most important technical and documentary aspects of the three Classes of the ASME III Code for vessels and the non-nuclear code BS 5500. A similar summary is also provided for the three Classes of ASME III rules for piping. The intention is that the paper provides a basis for appreciating the relative integrity afforded by these various rules. (author)

Application of ASME code AG-1 to YGN 3 ampersand 4 plants, South Korea

International Nuclear Information System (INIS)

Kim, Y.K.; Porco, R.D.; York, Y.D.

1993-01-01

Yonggwang Nuclear Power Plant Units 3 ampersand 4 are located on the southwestern coast of South Korea on the Yellow Sea. The plant is owned by Korea Electric Power Corp. (KEPCO), with the engineering being performed by Korea Power Engineering Co., Inc. (KOPEC) and Sargent and Lundy under a technology transfer agreement. The plants are both 950 Megawatt (electric) pressurized water reactors of US design. Under contract to KEPCO, Korea Heavy Industries and Construction Co., Ltd. and Ellis and Watts, Division of Dynamics Corporation of America, Batavia, Ohio, supplied major components to the YGN plants in compliance to ASME AG-1. These components included safety related Air Cleaning Units, Reactor containment Fan Cooler Units, Air Handling Units, Cubicle Coolers, Duct Electric Heaters, and fans. This paper details the extent of applicability of ASME Code AG-1 to the specific equipment, description of the equipment, conformance, testing, and design required. The paper also discusses the problems encountered in implementing ASME AG-1, working around Code sections that were not complete at contract inception, conflicts in project documents and related problems. Also discussed are the logistics problems, material availability, and quality assurance aspects complicating the applications of ASME AG-1, due to the required Korean content for some components. Based on successfully supplying the equipment referenced above, it has been concluded that AG-1 is a working document and can be successfully implemented. It provides the requirements necessary for performance, design, construction, acceptance testing, and quality assurance of equipment used as components in nuclear air and gas treatment systems in nuclear facilities. The paper also addresses lessons learned and aspects of mixing US design and US built components in Korean built assemblies

Comparison of the ASME Environmental Fatigue Design Curve with the Leax' Low Bound Model

International Nuclear Information System (INIS)

Jeong, Ill Seok; Kim, Wan Jae; Jun, Hyun Ik

2010-01-01

Environmental fatigue issue long time argued between industry and regulator. The issues of the debates are about environmental fatigue data only from experiment laboratories, no evidences in fields, and over conservatism. However, NRC issued the requirement to implement it to the construction design prior to industry practical design code. American Society of Mechanical Engineers (ASME) determined to issue non-mandatory code cases of environmental fatigue design. This paper evaluated the conservatism of the ASME proposed environmental fatigue design curve in comparison with the Leax' low bound approach model of environmental fatigue curve. A group of CF8M cast austenitic stainless steel (CASS) produced in KEPCO Research Center was introduced in the evaluation

Weldability and mechanical property characterization of weld clad alloy 800H tubesheet forging

International Nuclear Information System (INIS)

King, J.F.; McCoy, H.E.

1984-09-01

The weldability of an alloy 800H forging that simulates a steam generator tubesheet is studied. Weldability was of concern because a wide range of microstructures was present in this forging. The top and portions of the bottom were weld clad with ERNiC-3 weld metal to a thickness of 19 mm similar to that anticipated for HTGR steam generators. Examinations of the clad fusion line in various regions revealed no weldability problems except possibly on the bottom portion, which contained large grains and some as-cast structure. A few microfissures were evident in this region, but no excessive hot cracking tendency was observed. The tensile properties in all areas of the clad forging were reasonable and not influenced greatly by the microstructure. The elevated-temperature tests showed strong tendency for fracture in the heat-affected zone of the alloy 800H. Creep failure at 649 0 C consistently occurred in the heat-affected zone of the alloy 800H, but the creep strength exceeded the expected values for alloy 800H

Material Behavior Based Hybrid Process for Sheet Draw-Forging Thin Walled Magnesium Alloys

International Nuclear Information System (INIS)

Sheng, Z.Q.; Shivpuri, R.

2005-01-01

Magnesium alloys are conventionally formed at the elevated temperatures. The thermally improved formability is sensitive to the temperature and strain rate. Due to limitations in forming speeds, tooling strength and narrow processing windows, complex thin walled parts cannot be made by traditional warm drawing or hot forging processes. A hybrid process, which is based on the deformation mechanism of magnesium alloys at the elevated temperature, is proposed that combines warm drawing and hot forging modes to produce an aggressive geometry at acceptable forming speed. The process parameters, such as temperatures, forming speeds etc. are determined by the FEM modeling and simulation. Sensitivity analysis under the constraint of forming limits of Mg alloy sheet material and strength of tooling material is carried out. The proposed approach is demonstrated on a conical geometry with thin walls and with bottom features. Results show that designed geometry can be formed in about 8 seconds, this cannot be formed by conventional forging while around 1000s is required for warm drawing. This process is being further investigated through controlled experiments

46 CFR 56.01-2 - Incorporation by reference.

Science.gov (United States)

2010-10-01

... Welded Ferritic and Martensitic Stainless Steel Tubing for General Service (“ASTM A 268”), 56.60-1; (21) ASTM A 276-98, Standard Specification for Stainless Steel Bars and Shapes (“ASTM A 276”), 56.60-2; (22... (27) ASME B36.19M-2004 Stainless Steel Pipe (2004) (“ASME B36.19M”), 56.07-5; 56.60-1. (28) ASME SA...

Interband transitions in 106Pd, 152Sm, 152Gd and 182W

International Nuclear Information System (INIS)

Kartashov, V.M.; Oborovskij, A.I.; Troitskaya, A.G.

1990-01-01

Internal transitions in 106 Pd, 152 Sm, 152 Gd, 182 W nuclei, observed during decay of 152,152m Eu, 182,183 Ta, 106m Ag, are studied. The experimental characteristics of E0-transitions and E0-components of E0+M1+E2 type transitions in the studied nuclei, relative intensities of internal conversion electron lines during 182 Ta decay, multipolar composition and forbidden factor for 182 W and 183 W low-energy transitions, characteristics of transitions are presented

46 CFR 54.01-2 - Adoption of division 1 of section VIII of the ASME Boiler and Pressure Vessel Code.

Science.gov (United States)

2010-10-01

... Boiler and Pressure Vessel Code. 54.01-2 Section 54.01-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... division 1 of section VIII of the ASME Boiler and Pressure Vessel Code. (a) Pressure vessels shall be designed, constructed, and inspected in accordance with section VIII of the ASME Boiler and Pressure Vessel...

Effects of ASM-024, a modulator of acetylcholine receptor function, on airway responsiveness and allergen-induced responses in patients with mild asthma.

Science.gov (United States)

Boulet, Louis-Philippe; Gauvreau, Gail M; Cockcroft, Donald W; Davis, Beth; Vachon, Luc; Cormier, Yvon; O'Byrne, Paul M

2015-01-01

To evaluate the safety, tolerability and clinical activity of ASM-024, a new cholinergic compound with dual nicotinic and muscarinic activity, in mild allergic asthma. The present study involved 24 stable, mild allergic asthmatic subjects. In a cross-over design, ASM-024 (50 mg or 200 mg) or placebo were administered once daily by nebulization over three periods of nine consecutive days separated by a three-week washout. The effect of each treatment on the forced expiratory volume in 1 s (FEV1), provocative concentration of methacholine causing a 20% decline in FEV1 (PC20), early and late asthmatic responses, and allergen-induced inflammation were measured. Seventeen subjects completed the study. During treatment with ASM-024 at 50 mg or 200 mg, the PC20 value increased respectively from a mean (± SD) 2.56±3.86 mg/mL to 4.11 mg/mL (P=0.007), and from 3.12±4.37 mg/mL to 5.23 mg/mL (P=0.005) (no change with placebo). On day 7 (day preceding allergen challenge), postdosing FEV1 increased by 2.0% with 50 mg (P=0.005) and 1.9% with 200 mg (P=0.008) (placebo -1.1%). ASM-24 had no inhibitory effect on early and late asthmatic responses, nor on sputum eosinophil or neutrophil levels. ASM-024 induced no serious adverse events, but caused cough in 22% and 48% of the subjects with 50 mg and 200 mg, respectively, compared with 10% who were on placebo. ASM-024 did not inhibit allergen-induced asthmatic response and related airway inflammation, but reduced methacholine airway responsiveness and slightly improved lung function. The mechanism by which ASM-024 improves these outcomes requires further study.

The effects of thermomechanical history on the microstructure of a nickel-base superalloy during forging

Energy Technology Data Exchange (ETDEWEB)

Gardner, S., E-mail: 485354@swansea.ac.uk [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom); Li, W. [Rolls-Royce plc, PO Box 31, Derby DE24 8BJ (United Kingdom); Coleman, M. [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom); Johnston, R., E-mail: r.johnston@swansea.ac.uk [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom)

2016-06-21

The effect of thermo-mechanical history on hot compression behaviour and resulting microstructures of a nickel base superalloy is presented. Hot compression tests were carried out on HAYNES® 282® specimens to varying strains from 0.1 to 0.8. Both single pass and multi-pass tests were completed. 60 min inter-pass times were utilized to accurately replicate industrial forging practices. The effect of dynamic, metadynamic and static recrystallization during inter-pass times on flow stress was investigated. The resulting microstructures were analysed using scanning electron, optical microscopy and EBSD to relate grain size and homogeneity with flow stress data. The study showed a negligible difference between multi-pass and single pass tests for strain increments above 0.2. Therefore, when modelling similar low strain and strain rate forging processes in HAYNES® 282®, previous forging steps can be ignored.

31 CFR 370.40 - Can I be held accountable if my negligence contributes to a forged signature?

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Can I be held accountable if my negligence contributes to a forged signature? 370.40 Section 370.40 Money and Finance: Treasury Regulations... if my negligence contributes to a forged signature? (a) General. If your failure to exercise ordinary...

Sensitivity Analysis of Oxide Scale Influence on General Carbon Steels during Hot Forging

Directory of Open Access Journals (Sweden)

Bernd-Arno Behrens

2018-02-01

Full Text Available Increasing product requirements have made numerical simulation into a vital tool for the time- and cost-efficient process design. In order to accurately model hot forging processes with finite, element-based numerical methods, reliable models are required, which take the material behaviour, surface phenomena of die and workpiece, and machine kinematics into account. In hot forging processes, the surface properties are strongly affected by the growth of oxide scale, which influences the material flow, friction, and product quality of the finished component. The influence of different carbon contents on material behaviour is investigated by considering three different steel grades (C15, C45, and C60. For a general description of the material behaviour, an empirical approach is used to implement mathematical functions for expressing the relationship between flow stress and dominant influence variables like alloying elements, initial microstructure, and reheating mode. The deformation behaviour of oxide scale is separately modelled for each component with parameterized flow curves. The main focus of this work lies in the consideration of different materials as well as the calculation and assignment of their material properties in dependence on current process parameters by application of subroutines. The validated model is used to carry out the influence of various oxide scale parameters, like the scale thickness and the composition, on the hot forging process. Therefore, selected parameters have been varied within a numerical sensitivity analysis. The results show a strong influence of oxide scale on the friction behaviour as well as on the material flow during hot forging.

IL-17A acts via p38 MAPK to increase stability of TNF-alpha-induced IL-8 mRNA in human ASM.

Science.gov (United States)

Henness, Sheridan; van Thoor, Eveline; Ge, Qi; Armour, Carol L; Hughes, J Margaret; Ammit, Alaina J

2006-06-01

Human airway smooth muscle (ASM) plays an immunomodulatory role in asthma. Recently, IL-17A has become of increasing interest in asthma, being found at elevated levels in asthmatic airways and emerging as playing an important role in airway neutrophilia. IL-17A predominantly exerts its neutrophil orchestrating role indirectly via the induction of cytokines by resident airway structural cells. Here, we perform an in vitro study to show that although IL-17A did not induce secretion of the CXC chemokine IL-8 from ASM cells, IL-17A significantly potentiates TNF-alpha-induced IL-8 protein secretion and gene expression in a concentration- and time-dependent manner (P ASM cells, acting via a p38 MAPK-dependent posttranscriptional pathway to augment TNF-alpha-induced secretion of the potent neutrophil chemoattractant IL-8 from ASM cells.

A new Friction and Lubrication Test for Cold Forging

DEFF Research Database (Denmark)

Bay, Niels; Wibom, Ole; Aalborg Nielsen, J

1995-01-01

This paper presents a new friction and lubrication test for cold forging. The test allows controlled variation of the surface expansion in the range 0-2000%, the tool temperature in the range 20-270°C and the sliding length between 0 and infinite. Friction is decreasing with increasing temperature...

Understanding the Long-Term Spectral Variability of Cygnus X-1 from BATSE and ASM Observations

Science.gov (United States)

Zdziarski, Andrzej A.; Poutanen, Juri; Paciesas, William S.; Wen, Linqing; Six, N. Frank (Technical Monitor)

2002-01-01

We present a spectral analysis of observations of Cygnus X-1 by the RXTE/ASM (1.5-12 keV) and CGRO/BATSE (20-300 keV), including about 1200 days of simultaneous data. We find a number of correlations between intensities and hardnesses in different energy bands from 1.5 keV to 300 keV. In the hard (low) spectral state, there is a negative correlation between the ASM 1.5-12 keV flux and the hardness at any energy. In the soft (high) spectral state, the ASM flux is positively correlated with the ASM hardness (as previously reported) but uncorrelated with the BATSE hardness. In both spectral states, the BATSE hardness correlates with the flux above 100 keV, while it shows no correlation with the flux in the 20-100 keV range. At the same time, there is clear correlation between the BATSE fluxes below and above 100 keV. In the hard state, most of the variability can be explained by softening the overall spectrum with a pivot at approximately 50 keV. The observations show that there has to be another, independent variability pattern of lower amplitude where the spectral shape does not change when the luminosity changes. In the soft state, the variability is mostly caused by a variable hard (Comptonized) spectral component of a constant shape superimposed on a constant soft blackbody component. These variability patterns are in agreement with the dependence of the rms variability on the photon energy in the two states. We interpret the observed correlations in terms of theoretical Comptonization models. In the hard state, the variability appears to be driven mostly by changing flux in seed photons Comptonized in a hot thermal plasma cloud with an approximately constant power supply. In the soft state, the variability is consistent with flares of hybrid, thermal/nonthermal, plasma with variable power above a stable cold disk. Also, based on broadband pointed observations simultaneous with those of the ASM and BATSE, we find the intrinsic bolometric luminosity increases by a

High temperature structural integrity evaluation method and application studies by ASME-NH for the next generation reactor design

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Lee, Jae Han

2006-01-01

The main purpose of this paper is to establish the high temperature structural integrity evaluating procedures for the next generation reactors, which are to be operated at over 500 .deg. C and for 60 years. To do this, comparison studies of the high temperature structural design codes and assessment procedures such as the ASME-NH (USA), RCC-MR (France), DDS (Japan), and R5 (UK) are carried out in view of the accumulated inelastic strain and the creep-fatigue damage evaluations. Also the application procedures of the ASME-NH rules with the actual thermal and structural analysis results are described in detail. To overcome the complexity and the engineering costs arising from a real application of the ASME-NH rules by hand, all the procedures established in this study such as the time-dependent primary stress limits, total accumulated creep ratcheting strain limits, and the creep-fatigue damage limits are computerized and implemented into the SIE ASME-NH program. Using this program, the selected high temperature structures subjected to two cycle types are evaluated and the parametric studies for the effects of the time step size, primary load, number of cycles, normal temperature for the creep damage evaluations and the effects of the load history on the creep ratcheting strain calculations are investigated

Modification of the ASME code z-factor for circumferential surface crack in nuclear ferritic pipings

International Nuclear Information System (INIS)

Choi, Young Hwan; Chung, Yon Ki; Koh, Wan Young; Lee, Joung Bae

1996-01-01

The purpose of this paper is to modify the ASME Code Z-Factor, which is used in the evaluation of circumferential surface crack in nuclear ferritic pipings. The ASME Code Z-Factor is a load multiplier to compensate plastic load with elasto-plastic load. The current ASME Code Z-Factor underestimates pipe maximum load. In this study, the original SC. TNP method is modified first because the original SC. TNP method has a problem that the maximum allowable load predicted from the original SC. TNP method is slightly higher than that measured from the experiment. Then the new Z-Factor is developed using the modified SC. TNP method. The desirability of both the modified SC. TNP method and the new Z-Factor is examined using the experimental results for the circumferential surface crack in pipings. The results show that (1) the modified SC. TNP method is good for predicting the circumferential surface crack behavior in pipings, and (2) the Z-Factor obtained from the modified SC. TNP method well predicts the behavior of circumferential surface crack in ferritic pipings. 30 refs., 13 figs., 4 tabs. (author)

Iterative and non-iterative solutions of engine flows using ASM and k-ε turbulence models

International Nuclear Information System (INIS)

Khaleghi, H.; Fallah, E.

2003-01-01

Various turbulent models are widely developed in order to make a good prediction of turbulence phenomena in different applications. The standard k-ε model shows a poor prediction for some applications. The Reynolds Stress Model (RSM) is expected to give a better prediction of turbulent characteristics, because a separate differential equation for each Reynolds stress component is solved in this model. In order to save both time and memory in this calculation a new Algebraic Stress Model (ASM) which was developed by Lumly et al in 1995 is used for calculations of flow characteristics in the internal combustion engine chamber. With using turbulent realizability principles, this model becomes a powerful and reliable turbulence model. In this paper the abilities of the model is examined in internal combustion engine flows. The results of ASM and k-ε models are compared with the experimental data. It is shown that the poor predictions of k-ε model are modified by ASM model. Also in this paper non-iterative PISO and iterative SIMPLE solution algorithms are compared. The results show that the PISO solution algorithm is the preferred and more efficient procedure in the calculation of internal combustion engine. (author)

Investigating the effect of variable gutter technique as a novel method on vertical flow of material in closed die forging processes

Energy Technology Data Exchange (ETDEWEB)

Pourbashiri, M.; Sedighi, M. [Iran University, Tehran (Iran, Islamic Republic of)

2016-04-15

Recently, Variable gutter technique has been introduced as a novel method in order to reduce waste materials in closed-die forging processes. In this paper, the capability of this method is investigated for a family of forged parts that the vertical flow of material is the last stage of forming process. As a case study, using the variable gutter technique, the amount of waste material is decreased about 50% for a sample forged part with a local rising. The results of FVM simulations and experiments confirmed the effectiveness of the variable gutter technique in such forging processes. The vertical flow of material in the die cavity (h parameter), as a criterion, for different gutter width and thickness dimensions was examined by FVM simulations. The results shown that the gutter thickness has more effect on vertical flow of material than the gutter width. By decreasing the gutter thickness and increasing the gutter width, the amount of vertical flow of material is increased about 120% and 29%, respectively. Finally, A/H ratio (A = Max width of sectional area of a forged part, H = Max height of a forged part) is proposed as shape complexity factor of a forged part. The results of FVM simulations are indicated that for the ratio of A/H > 2, the variable gutter thickness technique is more effective and can be successfully used to reduce the amount of waste materials.

Application of directional solidification ingot (LSD) in forging of PWR reactor vessel heads

International Nuclear Information System (INIS)

Benhamou, C.; Poitrault, I.

1985-09-01

Creusot-Loire Industrie uses this type of ingot for manufacture of Framatome 1300 and 1450 MW 4-loop PWR reactor vessel heads. This type of ingot offers a number advantages: improved internal soundness; greater chemical, structural and mechanical homogeneity of the finished part; simplified forging process. After a brief description of the pouring and solidification processes, this paper presents an analysis of the results of examinations performed on the prototype forging, as well as review of results obtained during industrial fabrication of dished heads from LSD ingots. The advantages of the LSD ingot over conventional ingots are discussed in conclusion

Adoption of ASME Code Section XI for ISI to Research Reactors

International Nuclear Information System (INIS)

Tawfik, Y.E.; El-sesy, I.A.; Shaban, H.I.; Ibrahim, M.M.

2002-01-01

ETRR-2 (Second Egyptian thermal research reactor) is a multi-purpose, pool- type reactor with an open water surface and variable core arrangement. The core power is 22 MWth, cooled and moderated by light water and with beryllium reflectors. It contains plate- type fuel elements (MTR type, 19.7% enriched uranium) with aluminum clad. The ETRR-2 reactor consist of 57 systems and around 200 subsystems. These systems contain many mechanical components such as tanks, pipes, valves, pumps, heat exchangers, cooling tower, air compressors, and supports. In this present work, a trial was made to adopt the general requirements of ASME code, section XI to ETRR-2 research reactor. ASME (American Society of Mechanical Engineers) boiler and pressure vessel Code, section XI, provides requirements for in-service inspection (ISI) and in-service testing (IST) of components and systems, and repair/replacement activities in a nuclear power plant. Also, IAEA (International Atomic Energy Authority) has published some recommendations for ISI for research reactors similar to that rules and requirements specified in ASME. The complete ISI program requires several steps that have to be performed in sequence. These steps are described in many logic flow charts (LFC's). These logic flow charts include; the general LFC's for all steps required to complete ISI program, the LFC's for examination requirements, the LFC's for flaw evaluation modules, and the LFC's for acceptability of welds for class 1 components. This program includes, also, the inspection program for welded parts of the reactor components during its lifetime. This inspection program is applied for each system and subsystem of ETRR-2 reactor. It includes the examination area type, the component type, the part to be examined, the weld type, the examination method, the inspection program schedule, and the detailed figures of the welded components. (authors)

Effect of nonmetallic inclusions on anisotropy of ductility in 35KhN3MFA steel forgings

International Nuclear Information System (INIS)

Shtremel', M.A.; Yavojskij, V.I.; Volkov, V.A.; Chursin, G.M.; Chukhlov, V.I.; Fetisov, G.I.; Mochalin, N.K.; Smol'yaninov, L.V.

1980-01-01

Characteristics of nonmetaltic inclusions and anizotropy of ductility and of impuct strength of forgings of the 35KhN3MFA steel are compared at different variants of melting and outer-furnace treatment. It is shown that method of melting rugulates anisotropy of ductility primarily through deformability of large inclusions during forging. Deformability of inclusions considerably changes due to introduction of silicocalcium in iron mold [ru

Development of production technology and investigation of quality for forged-welded turbine rotors of steel 25Kh2NVFA

International Nuclear Information System (INIS)

Borisov, I.A.; Merinov, G.N.; Slezkina, E.V.

1997-01-01

A study was made into mechanical properties and microstructure of turbine rotor components manufactured by forging and heat treated under various conditions. It is revealed that the optimal heat treatment of forgings must include double quenching with subsequent tempering at 630-640 deg C for 10-20 h. Forged and welded rotors should be tempered at 620-630 deg C for 50-100 h. Microscopic examination and mechanical tests showed that low alloy steel 25Kh2NMF can be successfully used for manufacturing rotors of high-, medium-and low-heat turbines

Development of SiC Nanoparticles and Second Phases Synergistically Reinforced Mg-Based Composites Processed by Multi-Pass Forging with Varying Temperatures

Directory of Open Access Journals (Sweden)

Kaibo Nie

2018-01-01

Full Text Available In this study, SiC nanoparticles were added into matrix alloy through a combination of semisolid stirring and ultrasonic vibration while dynamic precipitation of second phases was obtained through multi-pass forging with varying temperatures. During single-pass forging of the present composite, as the deformation temperature increased, the extent of recrystallization increased, and grains were refined due to the inhibition effect of the increasing amount of dispersed SiC nanoparticles. A small amount of twins within the SiC nanoparticle dense zone could be found while the precipitated phases of Mg17Al12 in long strips and deformation bands with high density dislocations were formed in the particle sparse zone after single-pass forging at 350 °C. This indicated that the particle sparse zone was mainly deformed by dislocation slip while the nanoparticle dense zone may have been deformed by twinning. The yield strength and ultimate tensile strength of the composites were gradually enhanced through increasing the single-pass forging temperature from 300 °C to 400 °C, which demonstrated that initial high forging temperature contributed to the improvement of the mechanical properties. During multi-pass forging with varying temperatures, the grain size of the composite was gradually decreased while the grain size distribution tended to be uniform with reducing the deformation temperature and extending the forging passes. In addition, the amount of precipitated second phases was significantly increased compared with that after multi-pass forging under a constant temperature. The improvement in the yield strength of the developed composite was related to grain refinement strengthening and Orowan strengthening resulting from synergistical effect of the externally applied SiC nanoparticles and internally precipitated second phases.

Modelling the void deformation and closure by hot forging of ingot castings

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Kotas, Petr

2012-01-01

by mechanical deformation. The aim of this paper is to analyze numerically if and to what degree the voids areclosed by the forging. Using the commercial simulation software ABAQUS, both simplified model ingots and physically manufactured ingots containing prescribed void distributions are deformed and analyzed....... The analysis concernsboth the void density change and the location of the voids in the part after deformation. The latter can be important for the subsequent reliability of the parts, for instance regarding fatigue properties. The analysis incorporates the Gurson yield criterion for metals containing voids...... and focuses on how the voids deform depending on their size and distribution in the ingot as well ashow the forging forces are applied....

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

NARCIS (Netherlands)

Luger, T.; Leent, E.J. van; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A.C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; Valk, P.G.M. van der; Bos, J.D.

2001-01-01

BACKGROUND: SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. OBJECTIVES: This study was designed to determine

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

NARCIS (Netherlands)

Luger, T; Van Leent, EJM; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knulst, AC; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; van der Valk, P. G. M.; Bos, JD

Background SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. Objectives This study was: designed to determine

Design and test of ASME strainer for primary cooling system in HANARO

International Nuclear Information System (INIS)

Park, Yong-Chul; Ryu, Jeong-Soo

1999-01-01

The ASME strainers have been newly installed at the suction side of each reactor coolant pump to get rid of the foreign materials which may damage the pump impeller or interfere with the coolant path of fuel flow tube or primary plate type heat exchanger. The strainer was designed in accordance with ASME SEC. III, DIV. 1, ND and the structural integrity was verified by seismic analysis. The screen was designed in accordance with the effective void area from the result of flow analysis for T-type strainer. After installation of the strainer, it was confirmed through the field test that the flow characteristics of primary cooling system were not adversely affected. The pressure loss coefficient was calculated by Darcy equation using the pressure difference through each strainer and the flow rate measured during the strainer performance test. And these are useful data to predict flow variations by the pressure difference. (author)

49 CFR 173.182 - Barium azide-50 percent or more water wet.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Barium azide-50 percent or more water wet. 173.182 Section 173.182 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more...

Comparisons of ratchetting analysis methods using RCC-M, RCC-MR and ASME codes

International Nuclear Information System (INIS)

Yang Yu; Cabrillat, M.T.

2005-01-01

The present paper compares the simplified ratcheting analysis methods used in RCC-M, RCC-MR and ASME with some examples. Firstly, comparisons of the methods in RCC-M and efficiency diagram in RCC-MR are investigated. A special method is used to describe these two methods with curves in one coordinate, and the different conservation is demonstrated. RCC-M method is also be interpreted by SR (second ratio) and v (efficiency index) which is used in RCC-MR. Hence, we can easily compare the previous two methods by defining SR as abscissa and v as ordinate and plotting two curves of them. Secondly, comparisons of the efficiency curve in RCC-MR and methods in ASME-NH APPENDIX T are investigated, with significant creep. At last, two practical evaluations are performed to show the comparisons of aforementioned methods. (authors)

When a Plant Resistance Inducer Leaves the Lab for the Field: Integrating ASM into Routine Apple Protection Practices.

Science.gov (United States)

Marolleau, Brice; Gaucher, Matthieu; Heintz, Christelle; Degrave, Alexandre; Warneys, Romain; Orain, Gilles; Lemarquand, Arnaud; Brisset, Marie-Noëlle

2017-01-01

Plant resistance inducers, also called elicitors, could be useful to reduce the use of pesticides. However, their performance in controlling diseases in the field remains unsatisfactory due to lack of specific knowledge of how they can integrate crop protection practices. In this work, we focused on apple crop and acibenzolar- S -methyl (ASM), a well-known SAR (systemic acquired resistance) inducer of numerous plant species. We provide a protocol for orchard-effective control of apple scab due to the ascomycete fungus Venturia inaequalis , by applying ASM in combination with a light integrated pest management program. Besides we pave the way for future optimization levers by demonstrating in controlled conditions (i) the high influence of apple genotypes, (ii) the ability of ASM to prime defenses in newly formed leaves, (iii) the positive effect of repeated elicitor applications, (iv) the additive effect of a thinning fruit agent.

Army Combat Medic Resilience: The Process of Forging Loyalty.

Science.gov (United States)

Abraham, Preetha A; Russell, Dale W; Huffman, Sarah; Deuster, Patricia; Gibbons, Susanne W

2018-03-01

This study presents a grounded theory analysis of in-depth interviews of United States Army Combat Medics (CMs) who had served in Iraq and/or Afghanistan. The study explores how 17 CMs nominated by their peers as resilient cope with military stressors in order to identify the factors that enable them to thrive amidst harsh conditions. Four distinct categories of characteristics unique to this group emerged: (1) social bonding, (2) readiness, (3) dual loyalty as performance, and (4) leader by example. Forging loyalty underpins these characteristics and represents the main process used by resilient CMs and comprised three behavior patterns: (1) commitment to the family, (2) commitment to the military mission, and (3) commitment to their guiding religious and spiritual beliefs. Prominent behavioral tendencies of forging loyalty likely developed during childhood and re-enforced by families, friends, and other role models. Based on the findings, new training and education efforts should focus on developing positive emotional, environmental, and social resources to enhance the health and well-being of service members and their families.

Corticosteroid-Induced MKP-1 Represses Pro-Inflammatory Cytokine Secretion by Enhancing Activity of Tristetraprolin (TTP) in ASM Cells.

Science.gov (United States)

Prabhala, Pavan; Bunge, Kristin; Ge, Qi; Ammit, Alaina J

2016-10-01

Exaggerated cytokine secretion drives pathogenesis of a number of chronic inflammatory diseases, including asthma. Anti-inflammatory pharmacotherapies, including corticosteroids, are front-line therapies and although they have proven clinical utility, the molecular mechanisms responsible for their actions are not fully understood. The corticosteroid-inducible gene, mitogen-activated protein kinase (MAPK) phosphatase 1 (MKP-1, DUSP1) has emerged as a key molecule responsible for the repressive effects of steroids. MKP-1 is known to deactivate p38 MAPK phosphorylation and can control the expression and activity of the mRNA destabilizing protein-tristetraprolin (TTP). But whether corticosteroid-induced MKP-1 acts via p38 MAPK-mediated modulation of TTP function in a pivotal airway cell type, airway smooth muscle (ASM), was unknown. While pretreatment of ASM cells with the corticosteroid dexamethasone (preventative protocol) is known to reduce ASM synthetic function in vitro, the impact of adding dexamethasone after stimulation (therapeutic protocol) had not been explored. Whether dexamethasone modulates TTP in a p38 MAPK-dependent manner in this cell type was also unknown. We address this herein and utilize an in vitro model of asthmatic inflammation where ASM cells were stimulated with the pro-asthmatic cytokine tumor necrosis factor (TNF) and the impact of adding dexamethasone 1 h after stimulation assessed. IL-6 mRNA expression and protein secretion was significantly repressed by dexamethasone acting in a temporally distinct manner to increase MKP-1, deactivate p38 MAPK, and modulate TTP phosphorylation status. In this way, dexamethasone-induced MKP-1 acts via p38 MAPK to switch on the mRNA destabilizing function of TTP to repress pro-inflammatory cytokine secretion from ASM cells. J. Cell. Physiol. 231: 2153-2158, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

NARCIS (Netherlands)

Luger, T.; van Leent, E. J.; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A. C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; van der Valk, P. G.; Bos, J. D.

2001-01-01

SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy

Effects of boron additions and solutionizing treatments on microstructures and ductility of forged Ti–6Al–4V alloys

International Nuclear Information System (INIS)

Luan, J.H.; Jiao, Z.B.; Chen, G.; Liu, C.T.

2015-01-01

Highlights: • Proper boron additions and heat-treatments improve the ductility of Ti64 alloys. • Coarse TiB precipitates embrittle the Ti64 alloys causing ductility loss. • Modified Ti64 forged alloys with high strength and high ductility are developed. - Abstract: The effects of boron additions on the microstructure and mechanical properties of forged Ti–6Al–4V alloys in different heat-treatment conditions have been characterized by both experimental studies and thermodynamic calculations. The results indicate a combination of proper post-forging treatments and B additions are helpful for control of the prior-β grain size and the volume fraction of α phase, thereby tuning the ductility of the forged Ti–6Al–4V alloys. However, the B-containing alloys exhibit a significant drop in ductility if the solutionizing temperature is too high, and this embrittlement is mainly due to the coarsening of brittle TiB borides. The mechanism in this case is due to the cleavage fracture of TiB rather than its debonding with the matrix, as indicated by the observation of the aligned TiB borides on the matching areas of both halves of the fracture surfaces. Thus, the TiB size and orientation, the prior-β grain size, and the volume fraction of the α phase all play important roles in controlling the mechanical properties of the forged Ti–6Al–4V alloys. The current findings shed light on the composition–microstructure–ductility relationship in the forged Ti–6Al–4V alloys

Effects of boron additions and solutionizing treatments on microstructures and ductility of forged Ti–6Al–4V alloys

Energy Technology Data Exchange (ETDEWEB)

Luan, J.H.; Jiao, Z.B. [Center for Advanced Structural Materials, Department of Mechanical and Biomedical Engineering, College of Science and Engineering, City University of Hong Kong, Hong Kong (China); Chen, G. [Engineering Research Center of Materials Behavior and Design, Ministry of Education, Nanjing University of Science and Technology, Nanjing 210094 (China); Liu, C.T., E-mail: chainliu@cityu.edu.hk [Center for Advanced Structural Materials, Department of Mechanical and Biomedical Engineering, College of Science and Engineering, City University of Hong Kong, Hong Kong (China)

2015-03-05

Highlights: • Proper boron additions and heat-treatments improve the ductility of Ti64 alloys. • Coarse TiB precipitates embrittle the Ti64 alloys causing ductility loss. • Modified Ti64 forged alloys with high strength and high ductility are developed. - Abstract: The effects of boron additions on the microstructure and mechanical properties of forged Ti–6Al–4V alloys in different heat-treatment conditions have been characterized by both experimental studies and thermodynamic calculations. The results indicate a combination of proper post-forging treatments and B additions are helpful for control of the prior-β grain size and the volume fraction of α phase, thereby tuning the ductility of the forged Ti–6Al–4V alloys. However, the B-containing alloys exhibit a significant drop in ductility if the solutionizing temperature is too high, and this embrittlement is mainly due to the coarsening of brittle TiB borides. The mechanism in this case is due to the cleavage fracture of TiB rather than its debonding with the matrix, as indicated by the observation of the aligned TiB borides on the matching areas of both halves of the fracture surfaces. Thus, the TiB size and orientation, the prior-β grain size, and the volume fraction of the α phase all play important roles in controlling the mechanical properties of the forged Ti–6Al–4V alloys. The current findings shed light on the composition–microstructure–ductility relationship in the forged Ti–6Al–4V alloys.

The development of reactor vessel internal heavy forging for 1000 MW pressurized-water reactor nuclear power plant

International Nuclear Information System (INIS)

Zhang Zhifeng; Chen Yongbo; Ding Xiuping; Zhang Lingfang

2012-01-01

This Paper introduced the development of Reactor Vessel Internal (RVI) heavy forgings for 1000 MW Pressurized Water Reactor (PWR) nuclear power plant, analyzed the manufacture difficulties and technical countermeasures. The testing result of the product indicated that the performance of RVI heavy forgings manufactured by Shanghai Heavy Machinery Plant Ld. (SHMP) is outstanding and entirely satisfy the technical requirements for RVI product. (authors)

Effect of technological parameters on formability of semi-solid rheological casting-forging 6061 alloy

Directory of Open Access Journals (Sweden)

Jianbo TAN

2016-02-01

Full Text Available The 6061 alloy cooling curve is determined by analysis software, and the 6061 semi-solid alloy is prepared by manual paddling process. The primary solid fraction is tested through prepared water quenched samples under different temperature. With H1F100 type servo press and cup type test mold, the forming of the 6061 semi-solid alloy rheological casting-forging is made. The influence of alloy temperature, forming pressure, upper mould temperature and holding time on the formability of 6061 alloy is researched. The results show that within the same set of mold completing casting and forging of the alloy is feasible. Along with the increase of the alloy temperature and the upper mould temperature, the formability of finished products becomes better. Under this experimentation, when the temperature of the semi-solid alloy is amongst 642 ℃ to 645 ℃ and the upper mould preheating temperature is amongst 200 ℃ to 300 ℃, casting defects such as cold insulation will form in the casting-forging sample of semi-solid 6061 alloy with the prolongation of holding time.

2 CFR 182.115 - Does this part apply to me?

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Does this part apply to me? 182.115 Section 182.115 Grants and Agreements OFFICE OF MANAGEMENT AND BUDGET GOVERNMENTWIDE GUIDANCE FOR GRANTS AND AGREEMENTS Reserved GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Purpose and...

Multipass forging of Inconel 718 in the delta-Supersolvus domain: assessing and modeling microstructure evolution

Directory of Open Access Journals (Sweden)

Zouari Meriem

2014-01-01

Full Text Available This work is focused on the evolution of the microstructure of Inconel 718 during multi-pass forging processes. During the forming process, the material is subjected to several physical phenomena such as work-hardening, recovery, recrystallization and grain growth. In this work, transformation kinetics are modeled in the δ-Supersolvus domain (T>Tsolvus where the alloy is single-phase, all the alloying elements being dissolved into the FCC matrix. Torsion tests were used to simulate the forging process and recrystallization kinetics was modeled using a discontinuous dynamic recrystallization (DDRX two-site mean field model. The microstructure evolution under hot forging conditions is predicted in both dynamic and post-dynamic regimes based on the initial distribution of grain size and the evolution of dislocation density distribution during each step of the process. The model predicts recrystallization kinetics, recrystallized grain size distribution and stress–strain curve for different thermo-mechanical conditions and makes the connection between dynamic and post-dynamic regimes.

Effect of Friction on Barreling during cold Upset Forging of Aluminium 6082 Alloy Solid cylinders

Science.gov (United States)

Priyadarshini, Amrita; Kiran, C. P.; Suresh, K.

2018-03-01

Friction is one of the significant factors in forging operations since it affects metal flow in the die, forming load, strain distribution, tool and die life, surface quality of the product etc. In upset forging, the frictional forces at the die-workpiece interface oppose the outward flow of the material due to which the specimen develops a barrel shape. As a result, the deformation becomes non-uniform or inhomogeneous which is undesirable. Barreling can be reduced by applying effective lubricant on the surface of the platens. The objective of the present work is to study experimentally the effect of various frictional conditions (dry, grease, mineral oil) on barreling during upset forging of aluminum 6082 solid cylinders of different aspect ratio (length/diameter: 0.5, 0.75, 1). The friction coefficients are determined using the ring compression test. Curvature of barrel is determined based on the assumption that the curvature of the barrel follows the geometry of circular arc.

Effects of HIP and forging on fracture behaviour in cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure

International Nuclear Information System (INIS)

Uematsu, Y.; Tokaji, K.; Nishigaki, K.; Okajima, D.; Ogasawara, M.

2010-01-01

The cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure was developed as a die material due to its high hardness. In order to achieve high performances of dies, not only the hardness but also the mechanical properties such as fracture toughness and fatigue crack propagation (FCP) resistance should be improved. In this paper, hot isostatic pressing (HIP) or forging was applied to the cast iron to improve mechanical properties, and the fracture behaviour, such as flexural strength, fracture toughness and FCP, was studied. The average flexural strength was reduced by forging because of the enhanced notch sensitivity due to the increase in the hardness. The fracture toughness was not affected by HIP nor forging while its scatter was significantly reduced by both post-treatments. The intrinsic FCP resistance taking account of crack closure was the same regardless of the application of HIP or forging, indicating that a slight change in the microstructure resulting from both treatments and the presence of casting defects exerted little influence on FCP behaviour. It could be concluded that both HIP and forging could improve the hardness of the material, while fracture toughness and FCP resistance were maintained.

Lingon sa Iskolarsyip sa Dulaan (1948-2007 Looking Back on Theater Scholarship (1948-2007

Directory of Open Access Journals (Sweden)

Apolonio B. Chua

2012-12-01

Full Text Available From 1948 to 2007, the academic community produced about a hundred titles of theses and dissertations on drama and theater, or made use of data from drama and theater for larger spheres of studies. The current article looked into identifying trends and points of emphasis, as the researches and studies progressed through roughly half a century of research production in the academic setting. Inductive in approach and tentative and exploratory in its analysis, the study identified four trends and points of emphasis in research production. In the fifties and sixties, the emphasis was more on studying the play text or drama; studies veered towards a literary reading and orientation. Eventually, this trend gave way to studying the larger phenomenon of mounting, and the mise en scéne and the spectator became additional units of concern for research. Studies began to have sections on props, costumes, and staging techniques. In the eighties, a larger concern for looking at theater as social production followed. Participant observation, field work and ethnography gave equal emphasis on the social context of theater. Marxism and other perspectives from the social sciences framed theater studies then; correlations between theater and society became useful. Towards the last decade of the century, theater studies aimed at a more conceptual approach, emphasizing core concepts like panata and other related or equivalent terms, elevating and defining the study of theater as a study of culture itself. Gamit ang mahigit sa sandaang tesis at disertasyon hinggil sa dula at dulaan o sinasangkot ang mga ito na lumabas sa akademya mula 1948 hanggang 2007, kapwa sa Unibersidad ng Pilipinas at sa iba pa, nilayon ng “Lingon sa Iskolarsyip sa Dulaan (1948-2007” na pulsuhan ang pangkalahatang daloy, tutok, tunguhin o kalakaran sa pagdadala ng mga pag-aaral. Panimula at exploratory sa inductive nitong lapat, nakatukoy ang pag-aaral ng apat na sapit o tutok sa daloy ng

Integrity evaluation for stud female threads on pressure vessel according to ASME code using FEM

International Nuclear Information System (INIS)

Kim, Moon Young; Chung, Nam Yong

2003-01-01

The extension of design life among power plants is increasingly becoming a world-wide trend. Kori no.1 unit in Korea is operating two cycle. It has two man-ways for tube inspection in a steam generator which is one of the important components in a nuclear power plant. Especially, stud bolts for man-way cover have damaged by disassembly and assembly several times and degradation for bolt materials for long term operation. It should be evaluated and compared by ASME code criteria for integrity evaluation. Integrity evaluation criteria which has been made by the manufacturer is not applied on the stud bolts of nuclear pressure vessels directly because it is controlled by the yield stress of ASME code. It can apply evaluation criteria through FEM analysis to damaged female threads and to evaluated safety for helical-coil method which is used according to code case-N-496-1. From analysis results, we found that it is the same results between stress intensity which got from FEM analysis on damaged female threads over 10% by manufacture integrity criteria and 2/3 yield strength criteria on ASME code. It was also confirmed that the helical-coil repair method would be safe

miR-182 Regulates Metabolic Homeostasis by Modulating Glucose Utilization in Muscle

Directory of Open Access Journals (Sweden)

Duo Zhang

2016-07-01

Full Text Available Understanding the fiber-type specification and metabolic switch in skeletal muscle provides insights into energy metabolism in physiology and diseases. Here, we show that miR-182 is highly expressed in fast-twitch muscle and negatively correlates with blood glucose level. miR-182 knockout mice display muscle loss, fast-to-slow fiber-type switching, and impaired glucose metabolism. Mechanistic studies reveal that miR-182 modulates glucose utilization in muscle by targeting FoxO1 and PDK4, which control fuel selection via the pyruvate dehydrogenase complex (PDHC. Short-term high-fat diet (HFD feeding reduces muscle miR-182 levels by tumor necrosis factor α (TNFα, which contributes to the upregulation of FoxO1/PDK4. Restoration of miR-182 expression in HFD-fed mice induces a faster muscle phenotype, decreases muscle FoxO1/PDK4 levels, and improves glucose metabolism. Together, our work establishes miR-182 as a critical regulator that confers robust and precise controls on fuel usage and glucose homeostasis. Our study suggests that a metabolic shift toward a faster and more glycolytic phenotype is beneficial for glucose control.

A multi-scale approach for high cycle anisotropic fatigue resistance: Application to forged components

International Nuclear Information System (INIS)

Milesi, M.; Chastel, Y.; Hachem, E.; Bernacki, M.; Loge, R.E.; Bouchard, P.O.

2010-01-01

Forged components exhibit good mechanical strength, particularly in terms of high cycle fatigue properties. This is due to the specific microstructure resulting from large plastic deformation as in a forging process. The goal of this study is to account for critical phenomena such as the anisotropy of the fatigue resistance in order to perform high cycle fatigue simulations on industrial forged components. Standard high cycle fatigue criteria usually give good results for isotropic behaviors but are not suitable for components with anisotropic features. The aim is to represent explicitly this anisotropy at a lower scale compared to the process scale and determined local coefficients needed to simulate a real case. We developed a multi-scale approach by considering the statistical morphology and mechanical characteristics of the microstructure to represent explicitly each element. From stochastic experimental data, realistic microstructures were reconstructed in order to perform high cycle fatigue simulations on it with different orientations. The meshing was improved by a local refinement of each interface and simulations were performed on each representative elementary volume. The local mechanical anisotropy is taken into account through the distribution of particles. Fatigue parameters identified at the microscale can then be used at the macroscale on the forged component. The linkage of these data and the process scale is the fiber vector and the deformation state, used to calculate global mechanical anisotropy. Numerical results reveal an expected behavior compared to experimental tendencies. We proved numerically the dependence of the anisotropy direction and the deformation state on the endurance limit evolution.

Environmentally Benign Lubricant Systems For Cold, Warm And Hot Forging

DEFF Research Database (Denmark)

Bay, Niels

2010-01-01

paper gives an overview of these efforts substituting environmentally hazardous lubricants in cold, warm and hot forging. The paper is an extract of the keynote paper [3] written by the author together with eight co-authors referring to collected papers and other information from more than 30 different...

Parametric study of emerging high power accelerator applications using Accelerator Systems Model (ASM)

International Nuclear Information System (INIS)

Berwald, D.H.; Mendelsohn, S.S.; Myers, T.J.; Paulson, C.C.; Peacock, M.A.; Piaszczyk, CM.; Rathke, J.W.; Piechowiak, E.M.

1996-01-01

Emerging applications for high power rf linacs include fusion materials testing, generation of intense spallation neutrons for neutron physics and materials studies, production of nuclear materials and destruction of nuclear waste. Each requires the selection of an optimal configuration and operating parameters for its accelerator, rf power system and other supporting subsystems. Because of the high cost associated with these facilities, economic considerations become paramount, dictating a full evaluation of the electrical and rf performance, system reliability/availability, and capital, operating, and life cycle costs. The Accelerator Systems Model (ASM), expanded and modified by Northrop Grumman during 1993-96, provides a unique capability for detailed layout and evaluation of a wide variety of normal and superconducting accelerator and rf power configurations. This paper will discuss the current capabilities of ASM, including the available models and data base, and types of trade studies that can be performed for the above applications. (author)

Scope and implementation of standards ASME N510 / N511 in air treatment system (HVAC) of the Asco nuclear power plant; Alcance e implementacion de las normas ASME N511 en el sistema de tratamiento de aire (HVAC) de la central nuclear de Asco

Energy Technology Data Exchange (ETDEWEB)

Jaimot Jimenez, J. J.

2013-07-01

With the ITC for renewal of license units 1 and 2 of Asco, the CSN It required the commissioning tests underway in the air, according to ASME N510 filter units. It is required that, for safety-related units, to undertake preventive inspections according to ASME N511. All these requirements, in tight deadlines, have represented a great challenge for the organizations of maintenance and engineering of ANAV.

Development of a forging technology for the production of high-pressure compressor blades from γ-titanium aluminide. Project C: production of primary wrought material for the forging of turbine blades from gamma-TiAl and their microstructural optimization. Final report

International Nuclear Information System (INIS)

Appel, F.; Oehring, M.; Lorenz, U.; Wagner, R.

1999-01-01

By the development of a new canning technique which resulted in an effective thermal isolation of can and billet the flow stress mismatch of can and billet material could be minimized, which allowed crack-free and uniform extrusion. Using this technique which has been applied for patent hot extrusion is an effective and matured working method for ingot material. It allows to produce fine-grained and almost fully recrystallized material with increased workability as has been found by the determination of the forging window as well as by the successful forging of more than 200 compressor blades by the project partner Thyssen Umformtechnik. By forging under suited conditions also a microstructural homogenization is achieved in comparison to extruded material. (orig.)

A friction model for cold forging of aluminum, steel and stainless steel provided with conversion coating and solid film lubricant

DEFF Research Database (Denmark)

Bay, Niels; Eriksen, Morten; Tan, Xincai

2011-01-01

Adopting a simulative tribology test system for cold forging the friction stress for aluminum, steel and stainless steel provided with typical lubricants for cold forging has been determined for varying normal pressure, surface expansion, sliding length and tool/work piece interface temperature...

Developments of New Lubricants for Cold Forging of Stainless Steel

DEFF Research Database (Denmark)

Steenberg, Thomas; Christensen, Erik; Olesen, P.

1997-01-01

Two new lubricant systems for cold forging of stainless steel have been developed. The main component of these systems are FeCl3 and ZnCa2(PO4)2, respectively. Both lubricant systems have been tested using a backward extrusion test. The results show excellent lubricating properties with respect...

Ageing of forged superaustenitic stainless steel: Precipitate phases and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Anburaj, J., E-mail: janburaj@gmail.com [Department of Metallurgical Engineering, PSG College of Technology, Coimbatore 641 004 (India); Nazirudeen, S.S. Mohamed; Narayanan, R.; Anandavel, B.; Chandrasekar, A. [Department of Metallurgical Engineering, PSG College of Technology, Coimbatore 641 004 (India)

2012-02-15

Highlights: Black-Right-Pointing-Pointer Solutionizing of 1250 Degree-Sign C and ageing of 500-1000 Degree-Sign C was done for hot forged SASS. Black-Right-Pointing-Pointer Strength and toughness increased by 25% on hot forged than the cast SASS. Black-Right-Pointing-Pointer Amounts of precipitates after ageing were evaluated by thermo-calc. Black-Right-Pointing-Pointer Sigma forms from chi at 900 Degree-Sign C and contains constant Cr and Mo contents, unlike chi. Black-Right-Pointing-Pointer Sigma is incoherent, contains high Mo and causes low toughness at 900 Degree-Sign C. - Abstract: Cast superaustenitic stainless steel (SASS), of composition 19 wt% Cr, 20 wt% Ni, 7.5 wt% Mo and 0.37 wt% N, is hot forged at 1200 Degree-Sign C. The forging was then solutionized at 1250 Degree-Sign C and aged for 1 h and 10 h at different temperatures in the range of 500-1000 Degree-Sign C. Effect of these treatments on (i) hardness and (ii) fracture toughness based on impact energy is reported. Chi is formed from low temperatures up to 800 Degree-Sign C, and sigma at temperatures above 900 Degree-Sign C. A model is proposed to illustrate the dissolution of chi and sigma in austenite at elevated temperatures. Compared with chi, sigma contains more Mo. Toughness decreased with increasing amounts of chi and sigma precipitates. However, in the temperature range of 850-950 Degree-Sign C, low toughness was observed for relatively a short ageing time, although virtually the volume of sigma phase is very low. This is attributed to the presence of incoherent sigma in austenite matrix. Fractographs of the impact-tested samples indicated an increased tendency for brittle fracture with increasing ageing temperatures (increase in sigma content). Thermodynamic calculations substantiated (i) EDS results of composition of secondary phases present in the aged SASS and (ii) the proposed model. From these studies it is concluded that sigma is enriched in Mo at 900 Degree-Sign C and can be as

Tensile properties of a dual-axial forged Ti–Fe–Cu alloy containing boron

Energy Technology Data Exchange (ETDEWEB)

Zadorozhnyy, V.Yu., E-mail: zadorozhnyyvlad@gmail.com [National University of Science and Technology “MISIS”, Leninsky prospect, 4, Moscow 119049 (Russian Federation); Institute for Materials Research, Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577 (Japan); Shchetinin, I.V.; Chirikov, N.V. [National University of Science and Technology “MISIS”, Leninsky prospect, 4, Moscow 119049 (Russian Federation); Louzguine-Luzgin, D.V. [WPI Advanced Institute for Materials Research, Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577 (Japan)

2014-09-22

In the present work we introduce a micro/nano-structured α+β Ti-based low-alloy produced by the tilt-casting method and subjected to subsequent thermo-mechanical treatment. After hot dual-axial forging at 900 °C, subsequent heating at 700 °C and water quenching a Ti{sub 94}Fe{sub 3}Cu{sub 3}+1000 ppm of boron alloy, containing inexpensive alloying elements, showed an ultimate tensile strength value of about 950 MPa and percentage elongation of about 5.2%. It is shown that the intensive forging treatment and subsequent heat treatment are leading to significantly improved mechanical properties of such an alloy compared to the as-cast state.

Saúde Ambiental: uma Análise dos Resultados das Conferências Nacionais de Meio Ambiente, Saúde e Saúde Ambiental

Directory of Open Access Journals (Sweden)