PFP functional development planning guide

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The PFP Functional Development Planning Guide presents the strategy and process used for the identification, development, and analysis of functions (activities) necessary to satisfy the requirements within the Plutonium Finishing Plant (PFP) integrated project baseline. The functional analysis will provide the basis for the development of a function driven work breakdown structure. Future revisions to this document will include as attachments the results of the PFP Functional Analysis resulting from this approach. This document is intended be a Project-owned management tool. As such, the guide will periodically require revisions resulting from improvements of the information, processes, and techniques as now described

Plutonium Finishing Plan (PFP) Treatment and Storage Unit Interim Status Closure Plan

International Nuclear Information System (INIS)

PRIGNANO, A.L.

2000-01-01

This document describes the planned activities and performance standards for closing the Plutonium Finishing Plant (PFP) Treatment and Storage Unit. The PFP Treatment and Storage Unit is located within the 234-52 Building in the 200 West Area of the Hanford Facility. Although this document is prepared based upon Title 40 Code of Federal Regulations (CFR), Part 265, Subpart G requirements, closure of the unit will comply with Washington Administrative Code (WAC) 173-303-610 regulations pursuant to Section 5.3 of the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) Action Plan (Ecology et al. 1996). Because the PFP Treatment and Storage Unit manages transuranic mixed (TRUM) waste, there are many controls placed on management of the waste. Based on the many controls placed on management of TRUM waste, releases of TRUM waste are not anticipated to occur in the PFP Treatment and Storage Unit. Because the intention is to clean close the PFP Treatment and Storage Unit, postclosure activities are not applicable to this closure plan. To clean close the unit, it will be demonstrated that dangerous waste has not been left onsite at levels above the closure performance standard for removal and decontamination. If it is determined that clean closure is not possible or is environmentally impractical, the closure plan will be modified to address required postclosure activities. The PFP Treatment and Storage Unit will be operated to immobilize and/or repackage plutonium-bearing waste in a glovebox process. The waste to be processed is in a solid physical state (chunks and coarse powder) and will be sealed into and out of the glovebox in closed containers. The containers of immobilized waste will be stored in the glovebox and in additional permitted storage locations at PFP. The waste will be managed to minimize the potential for spills outside the glovebox, and to preclude spills from reaching soil. Containment surfaces will be maintained to ensure

PFP requirements development planning guide

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The PFP Requirements Development Planning Guide presents the strategy and process used for the identification, allocation, and maintenance of requirements within the Plutonium Finishing Plant (PFP) integrated project baseline. Future revisions to this document will be included as attachments (e.g., results of the PFP Requirements Analysis attributable to this approach). This document is intended be a Project-owned management tool. As such, this document will periodically require revisions resulting from improvements of the information, processes, and techniques as now described. Future updates may be made to this document by PFP management and final approval of the content will be accomplished in a Baseline Change Request as it impacts the Multi-Year Work Plan, or baseline information managed in the Hanford Site Systems Engineering Baseline

Plutonium vulnerability issues at Hanford's Plutonium Finishing Plant

International Nuclear Information System (INIS)

Feldt, E.; Templeton, D.W.; Tholen, E.

1995-01-01

The Plutonium Finishing Plant (PFP) at the Hanford, Washington Site was operated to produce plutonium (Pu) metal and oxide for national defense purposes. Due to the production requirements and methods utilized to meet national needs and the abrupt shutdown of the plant in the late 1980s, the plant was left in a condition that poses a risk of radiation exposure to plant workers, of accidental radioactive material release to the environment, and of radiation exposure to the public. In early 1994, an Environmental Impact Statement (EIS) to determine the best methods for cleaning out and stabilizing Pu materials in the PFP was started. While the EIS is being prepared, a number of immediate actions have been completed or are underway to significantly reduce the greatest hazards in the PFP. Recently, increased attention his been paid to Pu risks at Department of Energy (DOE) facilities resulting in the Department-wide Plutonium Vulnerability Assessment and a recommendation by the Defense Nuclear Facilities Safety Board (DNFSB) for DOE to develop integrated plans for managing its nuclear materials

Maintenance implementation plan for the Plutonium Finishing Plant. Revision 3

International Nuclear Information System (INIS)

Meldrom, C.A.

1996-03-01

This document outlines the Maintenance Implementation Plan (MIP) for the Plutonium Finishing Plant (PFP) located at the Hanford site at Richland, Washington. This MIP describes the PFP maintenance program relative to DOE order 4330.4B. The MIP defines the key actions needed to meet the guidelines of the Order to produce a cost-effective and efficient maintenance program. A previous report identified the presence of significant quantities of Pu-bearing materials within PFP that pose risks to workers. PFP's current mission is to develop, install and operate processes which will mitigate these risks. The PFP Maintenance strategy is to equip the facility with systems and equipment able to sustain scheduled PFP operations. The current operating run is scheduled to last seven years. Activities following the stabilization operation will involve an Environmental Impact Statement (EIS) to determine future plant activities. This strategy includes long-term maintenance of the facility for safe occupancy and material storage. The PFP maintenance staff used the graded approach to dictate the priorities of the improvement and upgrade actions identified in Chapter 2 of this document. The MIP documents PFP compliance to the DOE 4330.4B Order. Chapter 2 of the MIP follows the format of the Order in addressing the eighteen elements. As this revision is a total rewrite, no sidebars are included to highlight changes

PFP dangerous waste training plan

International Nuclear Information System (INIS)

Khojandi, J.

1996-01-01

This document establishes the minimum training requirements for the Plutonium Finishing Plant (PFP) personnel who are responsible for management of dangerous waste. The training plan outlines training requirements for handling of solid dangerous waste during generator accumulation and liquid dangerous waste during treatment and storage operations. The implementation of this training plan will ensure the PFP facility compliance with the training plan requirements of Dangerous Waste Regulation. Chapter 173-303-330. Washington Administrative Code (WAC). The requirements for such compliance is described in Section 11.0 of WHC-CM-7-5 Environmental Compliance Manual

Interface Control Document Between the Double Shell Tanks (DST) System and the Plutonium Finishing Plan (PFP)

International Nuclear Information System (INIS)

MAY, T.H.

1999-01-01

This document identifies the requirements and responsibilities for all parties to support waste transfer from the Plutonium Finishing Plant (PFP) facility to the Double-Shell Tank (DST) System of the River Protection Project (RPP). This Interface Control Document (ICD) will not attempt to control the physical portion of this interface because the physical equipment making up this interface, and any associated interface requirements, are already in place, operational and governed by existing operating specifications and other documentation. The PFP and DST Systems have a direct physical interface (the waste transfer pipeline) that travels between the 241-2 Building (TK-D5) and DST SY-102 via 244-TX double-contained receiver tank (DCRT). The purpose of the ICD process is to formalize working agreements between the RPP DST System and organization/companies internal and external to RPP. This ICD has been developed as part of the requirements basis for design of the DST System to support the Phase I Privatization effort

Sludge stabilization at the Plutonium Finishing Plant, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1994-10-01

This Environmental Assessment evaluates the proposed action to operate two laboratory-size muffle furnaces in glovebox HC-21C, located in the Plutonium Finishing Plant (PFP), Hanford Site, Richland, Washington. The muffle furnaces would be used to stabilize chemically reactive sludges that contain approximately 25 kilograms (55 pounds) of plutonium by heating to approximately 500 to 1000 degrees C (900 to 1800 degrees F). The resulting stable powder, mostly plutonium oxide with impurities, would be stored in the PFP vaults. The presence of chemically reactive plutonium-bearing sludges in the process gloveboxes poses a risk to workers from radiation exposure and limits the availability of storage space for future plant cleanup. Therefore, there is a need to stabilize the material into a form suitable for long-term storage. This proposed action would be an interim action, which would take place prior to completion of an Environmental Impact Statement for the PFP which would evaluate stabilization of all plutonium-bearing materials and cleanout of the facility. However, only 10 percent of the total quantity of plutonium in reactive materials is in the sludges, so this action will not limit the choice of reasonable alternatives or prejudice the Record of Decision of the Plutonium Finishing Plant Environmental Impact Statement

PFP solution stabilization

International Nuclear Information System (INIS)

Aftanas, B.L.

1996-01-01

This Functional Design Criteria (FDC) addresses remediation of the plutonium-bearing solutions currently in inventory at the Plutonium Finishing Plant (PFP). The recommendation from the Environmental Impact Statement (EIS) is that the solutions be treated thermally and stabilized as a solid for long term storage. For solutions which are not discardable, the baseline plan is to utilize a denitration process to stabilize the solutions prior to packaging for storage

PFP supply fan motor starters

International Nuclear Information System (INIS)

Keck, R.D.

1995-01-01

The Plutonium Finishing Plant (PFP) is currently stabilizing about 25 kg of Pu sludge; upon completion of this task, PFP will be maintained in a safe standby condition to await decision from the PFP NEPA review. It can take about 10 years to initiate and complete terminal cleanout after this; the facility will then be decommissioned and decontaminated. The 234-5Z ventilation system must continue to operate until terminal cleanout. Part of the ventilation system is the seismic fan shutdown system which shuts down the ventilation supply fans in case of strong earthquake. This document presents criteria for installing solid state, reduced voltage motor starters and isolation contactors for the 8 main ventilation supply fans. The isolation contactors will shutdown the supply fans in event of earthquake

ASSESSING CHEMICAL HAZARDS AT THE PLUTONIUM FINISHING PLANT FOR PLANNING FUTURE DECONTAMINATION AND DECOMMISSIONING

International Nuclear Information System (INIS)

HOPKINS, A.M.; KLOS, D.B.; MINETT, M.J.

2007-01-01

This paper documents the fiscal year (FY) 2006 assessment to evaluate potential chemical and radiological hazards associated with vessels and piping in the former plutonium process areas at Hanford's Plutonium Finishing Plant (PFP). Evaluations by PFP engineers as design authorities for specific systems and other subject-matter experts were conducted to identify the chemical hazards associated with transitioning the process areas for the long-term layup of PFP before its eventual final decontamination and decommissioning (D and D). D and D activities in the main process facilities were suspended in September 2005 for a period of between 5 and 10 years. A previous assessment conducted in FY 2003 found that certain activities to mitigate chemical hazards could be deferred safely until the D and D of PFP, which had been scheduled to result in a slab-on-grade condition by 2009. As a result of necessary planning changes, however, D and D activities at PFP will be delayed until after the 2009 time frame. Given the extended project and plant life, it was determined that a review of the plant chemical hazards should be conducted. This review to determine the extended life impact of chemicals is called the ''Plutonium Finishing Plant Chemical Hazards Assessment, FY 2006''. This FY 2006 assessment addresses potential chemical and radiological hazard areas identified by facility personnel and subject-matter experts who reevaluated all the chemical systems (items) from the FY 2003 assessment. This paper provides the results of the FY 2006 chemical hazards assessment and describes the methodology used to assign a hazard ranking to the items reviewed

Characterization of past and present solid waste streams from the plutonium finishing plant

Energy Technology Data Exchange (ETDEWEB)

Duncan, D.R.; Mayancsik, B.A. [Westinghouse Hanford Co., Richland, WA (United States); Pottmeyer, J.A.; Vejvoda, E.J.; Reddick, J.A.; Sheldon, K.M.; Weyns, M.I. [Los Alamos Technical Associates, Kennewick, WA (United States)

1993-02-01

During the next two decades the transuranic (TRU) wastes now stored in the burial trenches and storage facilities at the Hanford Site are to be retrieved, processed at the Waste Receiving and Processing (WRAP) Facility, and shipped to the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico for final disposal. Over 50% of the TRU waste to be retrieved for shipment to the WIPP has been generated at the Plutonium Finishing Plant (PFP), also known as the Plutonium Processing and Storage Facility and Z Plant. The purpose of this report is to characterize the radioactive solid wastes generated by the PFP since its construction in 1947 using process knowledge, existing records, and history-obtained from interviews. The PFP is currently operated by Westinghouse Hanford Company (WHC) for the US Department of Energy (DOE).

Characterization of past and present solid waste streams from the plutonium finishing plant

International Nuclear Information System (INIS)

Duncan, D.R.; Mayancsik, B.A.; Pottmeyer, J.A.; Vejvoda, E.J.; Reddick, J.A.; Sheldon, K.M.; Weyns, M.I.

1993-02-01

During the next two decades the transuranic (TRU) wastes now stored in the burial trenches and storage facilities at the Hanford Site are to be retrieved, processed at the Waste Receiving and Processing (WRAP) Facility, and shipped to the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico for final disposal. Over 50% of the TRU waste to be retrieved for shipment to the WIPP has been generated at the Plutonium Finishing Plant (PFP), also known as the Plutonium Processing and Storage Facility and Z Plant. The purpose of this report is to characterize the radioactive solid wastes generated by the PFP since its construction in 1947 using process knowledge, existing records, and history-obtained from interviews. The PFP is currently operated by Westinghouse Hanford Company (WHC) for the US Department of Energy (DOE)

The Integrated Safety Management System Verification Enhancement Review of the Plutonium Finishing Plant (PFP)

International Nuclear Information System (INIS)

BRIGGS, C.R.

2000-01-01

The primary purpose of the verification enhancement review was for the DOE Richland Operations Office (RL) to verify contractor readiness for the independent DOE Integrated Safety Management System Verification (ISMSV) on the Plutonium Finishing Plant (PFP). Secondary objectives included: (1) to reinforce the engagement of management and to gauge management commitment and accountability; (2) to evaluate the ''value added'' benefit of direct public involvement; (3) to evaluate the ''value added'' benefit of direct worker involvement; (4) to evaluate the ''value added'' benefit of the panel-to-panel review approach; and, (5) to evaluate the utility of the review's methodology/adaptability to periodic assessments of ISM status. The review was conducted on December 6-8, 1999, and involved the conduct of two-hour interviews with five separate panels of individuals with various management and operations responsibilities related to PFP. A semi-structured interview process was employed by a team of five ''reviewers'' who directed open-ended questions to the panels which focused on: (1) evidence of management commitment, accountability, and involvement; and, (2) consideration and demonstration of stakeholder (including worker) information and involvement opportunities. The purpose of a panel-to-panel dialogue approach was to better spotlight: (1) areas of mutual reinforcement and alignment that could serve as good examples of the management commitment and accountability aspects of ISMS implementation, and, (2) areas of potential discrepancy that could provide opportunities for improvement. In summary, the Review Team found major strengths to include: (1) the use of multi-disciplinary project work teams to plan and do work; (2) the availability and broad usage of multiple tools to help with planning and integrating work; (3) senior management presence and accessibility; (4) the institutionalization of worker involvement; (5) encouragement of self-reporting and self

PFP issues/assumptions development and management planning guide

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The PFP Issues/Assumptions Development and Management Planning Guide presents the strategy and process used for the identification, allocation, and maintenance of an Issues/Assumptions Management List for the Plutonium Finishing Plant (PFP) integrated project baseline. Revisions to this document will include, as attachments, the most recent version of the Issues/Assumptions Management List, both open and current issues/assumptions (Appendix A), and closed or historical issues/assumptions (Appendix B). This document is intended be a Project-owned management tool. As such, this document will periodically require revisions resulting from improvements of the information, processes, and techniques as now described. Revisions that suggest improved processes will only require PFP management approval

Technical Basis Document for PFP Area Monitoring Dosimetry Program

CERN Document Server

Cooper, J R

2000-01-01

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual.

Technical Basis Document for PFP Area Monitoring Dosimetry Program

International Nuclear Information System (INIS)

COOPER, J.R.

2000-01-01

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual

Technical Basis Document for PFP Area Monitoring Dosimetry Program

Energy Technology Data Exchange (ETDEWEB)

COOPER, J.R.

2000-04-17

This document describes the phantom dosimetry used for the PFP Area Monitoring program and establishes the basis for the Plutonium Finishing Plant's (PFP) area monitoring dosimetry program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), part 835, ''Occupational Radiation Protection'' Part 835.403; Hanford Site Radiological Control Manual (HSRCM-1), Part 514; HNF-PRO-382, Area Dosimetry Program; and PNL-MA-842, Hanford External Dosimetry Technical Basis Manual.

Plutonium Finishing Plant (PFP) Criticality Alarm System Commercial Grade Item (CGI) Critical Characteristics

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for PFP's criticality alarm system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item. PFP's Criticality Alarm System includes the nine criticality alarm system panels and their associated hardware. This includes all parts up to the first breaker in the electrical distribution system. Specific system boundaries and justifications are contained in HNF-SD-CP-SDD-003, ''Definition and Means of Maintaining the Criticality Detectors and Alarms Portion of the PFP Safety Envelope.'' The procurement requirements associated with the system necessitates procurement of some system equipment as Commercial Grade Items in accordance with HNF-PRO-268, ''Control of Purchased Items and Services.''

Plan for the Initiation of HA-211 Furnace Operations at the Plutonium Finishing Plan (PFP)

International Nuclear Information System (INIS)

WILLIS, H.T.

2000-01-01

This plan provides a phased approach authorizing the use of three additional muffle furnaces for thermal stabilization. Achievement of Thermal Stabilization mission elements require the installation and startup of three additional muffle furnaces for the thermal stabilization of plutonium and plutonium bearing materials at the Plutonium Finishing Plant (PFP). The release to operate these additional furnaces will require an Activity Based Startup Review. The conduct of the Activity Based Startup Review (ABSR) was approved by Fluor Daniel Hanford on October 15, 1999. This plan has been developed with the objective of identifying those activities needed to guide the controlled startup of five furnaces from authorization to unrestricted operations by adding the HA-211 furnaces in an orderly and safe manner after the approval to Startup has been given

PLUTONIUM FINISHING PLANT (PFP) 241-Z LIQUID WASTE TREATMENT FACILITY DEACTIVATION AND DEMOLITION

International Nuclear Information System (INIS)

JOHNSTON GA

2008-01-01

Fluor Hanford, Inc. (FH) is proud to submit the Plutonium Finishing Plant (PFP) 241-Z liquid Waste Treatment Facility Deactivation and Demolition (D and D) Project for consideration by the Project Management Institute as Project of the Year for 2008. The decommissioning of the 241-Z Facility presented numerous challenges, many of which were unique with in the Department of Energy (DOE) Complex. The majority of the project budget and schedule was allocated for cleaning out five below-grade tank vaults. These highly contaminated, confined spaces also presented significant industrial safety hazards that presented some of the most hazardous work environments on the Hanford Site. The 241-Z D and D Project encompassed diverse tasks: cleaning out and stabilizing five below-grade tank vaults (also called cells), manually size-reducing and removing over three tons of process piping from the vaults, permanently isolating service utilities, removing a large contaminated chemical supply tank, stabilizing and removing plutonium-contaminated ventilation ducts, demolishing three structures to grade, and installing an environmental barrier on the demolition site . All of this work was performed safely, on schedule, and under budget. During the deactivation phase of the project between November 2005 and February 2007, workers entered the highly contaminated confined-space tank vaults 428 times. Each entry (or 'dive') involved an average of three workers, thus equaling approximately 1,300 individual confined -space entries. Over the course of the entire deactivation and demolition period, there were no recordable injuries and only one minor reportable skin contamination. The 241-Z D and D Project was decommissioned under the provisions of the 'Hanford Federal Facility Agreement and Consent Order' (the Tri-Party Agreement or TPA), the 'Resource Conservation and Recovery Act of 1976' (RCRA), and the 'Comprehensive Environmental Response, Compensation, and Liability Act of 1980

PFP total process throughput calculation and basis of estimate

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The PFP Process Throughput Calculation and Basis of Estimate document provides the calculated value and basis of estimate for process throughput associated with material stabilization operations conducted in 234-52 Building. The process throughput data provided reflects the best estimates of material processing rates consistent with experience at the Plutonium Finishing Plant (PFP) and other U.S. Department of Energy (DOE) sites. The rates shown reflect demonstrated capacity during ''full'' operation. They do not reflect impacts of building down time. Therefore, these throughput rates need to have a Total Operating Efficiency (TOE) factor applied

Anticipated Radiological Dose to Worker for Plutonium Stabilization and Handling at PFP - Project W-460

International Nuclear Information System (INIS)

WEISS, E.V.

2000-01-01

This report provides estimates of the expected whole body and extremity radiological dose, expressed as dose equivalent (DE), to workers conducting planned plutonium (Pu) stabilization processes at the Hanford Site Plutonium Finishing Plant (PFP). The report is based on a time and motion dose study commissioned for Project W-460, Plutonium Stabilization and Handling, to provide personnel exposure estimates for construction work in the PFP storage vault area plus operation of stabilization and packaging equipment at PFP

Anticipated Radiological Dose to Worker for Plutonium Stabilization and Handling at PFP - Project W-460

CERN Document Server

Weiss, E V

2000-01-01

This report provides estimates of the expected whole body and extremity radiological dose, expressed as dose equivalent (DE), to workers conducting planned plutonium (Pu) stabilization processes at the Hanford Site Plutonium Finishing Plant (PFP). The report is based on a time and motion dose study commissioned for Project W-460, Plutonium Stabilization and Handling, to provide personnel exposure estimates for construction work in the PFP storage vault area plus operation of stabilization and packaging equipment at PFP.

Plan for the Startup of HA-21I Furnace Operations at the Plutonium Finishing Plant (PFP)

International Nuclear Information System (INIS)

WILLIS, H.T.

2000-01-01

Achievement of Thermal Stabilization mission elements require the installation and startup of three additional muffle furnaces for the thermal stabilization of plutonium and plutonium bearing materials at the Plutonium Finishing Plant (PFP). The release to operate these additional furnaces will require an Activity Based Startup Review. The conduct of the Activity Based Startup Review (ABSR) was approved by Fluor Daniel Hanford on October 15, 1999. This plan has been developed with the objective of identifying those activities needed to guide the controlled startup of five furnaces from authorization to unrestricted operations by adding the HA-211 furnaces in an orderly and safe manner after the approval to Startup has been given. The Startup Plan provides a phased approach that bridges the activities between the completion of the Activity Based Startup Review authorizing the use of the three additional furnaces and the unrestricted operation of the five thermal stabilization muffle furnaces. The four phases are: (1) the initiation of five furnace operations using three empty (simulated full) boat charges from HA-211 and two full charges from HC-21C; (2) three furnace operations (one full charge from HA-211 and two full charges from HC-21C); (3) four furnace operations (two full charges from HA-211 and two full charges from HC-21C); and (4) integrated five furnace operations and unrestricted operations. Phase 1 of the Plan will be considered as the cold runs. This Plan also provides management oversight and administrative controls that are to be implemented until unrestricted operations are authorized. It also provides a formal review process for ensuring that all preparations needed for full five furnace operations are completed and formally reviewed prior to proceeding to the increased activity levels associated with five furnace operations. Specific objectives include: (1) To ensure that activities are conducted in a safe manner. (2) To provide supplemental

System Design Description PFP Thermal Stabilization

International Nuclear Information System (INIS)

RISENMAY, H.R.

2000-01-01

The purpose of this document is to provide a system design description (SDD) and design basis for the Plutonium Finishing Plant (PFP) Thermal Stabilization project. The chief objective of the SDD is to document the Structures, Systems, and Components (SSCs) that establish and maintain the facility Safety Envelope necessary for normal safe operation of the facility; as identified in the FSAR, the OSRs, and Safety Assessment Documents (SADs). This safety equipment documentation should satisfy guidelines for the SDD given in WHC-SD-CP-TI-18 1, Criteria for Identification and Control of Equipment Necessary for Preservation of the Safety Envelope and Safe Operation of PFP. The basis for operational, alarm response, maintenance, and surveillance procedures are also identified and justified in this document. This document and its appendices address the following elements of the PFP Thermal Stabilization project: Functional and design requirements; Design description; Safety Envelope Analysis; Safety Equipment Class; and Operational, maintenance and surveillance procedures

Fire hazard analysis for Plutonium Finishing Plant complex

International Nuclear Information System (INIS)

MCKINNIS, D.L.

1999-01-01

A fire hazards analysis (FHA) was performed for the Plutonium Finishing Plant (PFP) Complex at the Department of Energy (DOE) Hanford site. The scope of the FHA focuses on the nuclear facilities/structures in the Complex. The analysis was conducted in accordance with RLID 5480.7, [DOE Directive RLID 5480.7, 1/17/94] and DOE Order 5480.7A, ''Fire Protection'' [DOE Order 5480.7A, 2/17/93] and addresses each of the sixteen principle elements outlined in paragraph 9.a(3) of the Order. The elements are addressed in terms of the fire protection objectives stated in paragraph 4 of DOE 5480.7A. In addition, the FHA also complies with WHC-CM-4-41, Fire Protection Program Manual, Section 3.4 [1994] and WHC-SD-GN-FHA-30001, Rev. 0 [WHC, 1994]. Objectives of the FHA are to determine: (1) the fire hazards that expose the PFP facilities, or that are inherent in the building operations, (2) the adequacy of the fire safety features currently located in the PFP Complex, and (3) the degree of compliance of the facility with specific fire safety provisions in DOE orders, related engineering codes, and standards

CSER 99-001: PFP LAB Dentirating calciner

International Nuclear Information System (INIS)

MILLER, E.M.; DOBBIN, K.D.

1999-01-01

A criticality safety evaluation report was prepared for the Plutonium Finishing Plant (PFP) laboratory denigrating calciner, located in Glovebox 188-1, that converts Pu(NO 3 ) 4 solutions to the high fired stable oxide PuO 2 . Fissile mass limits and volume limits are set for the glovebox for testing operations and training operators using only nitric acid feed to a plutonium oxide bed in the calciner

PLUTONIUM FINISHING PLANT (PFP) 241-Z LIQUID WASTE TREATMENT FACILITY DEACTIVATION AND DEMOLITION

Energy Technology Data Exchange (ETDEWEB)

JOHNSTON GA

2008-01-15

Fluor Hanford, Inc. (FH) is proud to submit the Plutonium Finishing Plant (PFP) 241-Z liquid Waste Treatment Facility Deactivation and Demolition (D&D) Project for consideration by the Project Management Institute as Project of the Year for 2008. The decommissioning of the 241-Z Facility presented numerous challenges, many of which were unique with in the Department of Energy (DOE) Complex. The majority of the project budget and schedule was allocated for cleaning out five below-grade tank vaults. These highly contaminated, confined spaces also presented significant industrial safety hazards that presented some of the most hazardous work environments on the Hanford Site. The 241-Z D&D Project encompassed diverse tasks: cleaning out and stabilizing five below-grade tank vaults (also called cells), manually size-reducing and removing over three tons of process piping from the vaults, permanently isolating service utilities, removing a large contaminated chemical supply tank, stabilizing and removing plutonium-contaminated ventilation ducts, demolishing three structures to grade, and installing an environmental barrier on the demolition site . All of this work was performed safely, on schedule, and under budget. During the deactivation phase of the project between November 2005 and February 2007, workers entered the highly contaminated confined-space tank vaults 428 times. Each entry (or 'dive') involved an average of three workers, thus equaling approximately 1,300 individual confined -space entries. Over the course of the entire deactivation and demolition period, there were no recordable injuries and only one minor reportable skin contamination. The 241-Z D&D Project was decommissioned under the provisions of the 'Hanford Federal Facility Agreement and Consent Order' (the Tri-Party Agreement or TPA), the 'Resource Conservation and Recovery Act of 1976' (RCRA), and the 'Comprehensive Environmental Response, Compensation, and

PFP vault operations containers for Plutonium Handling and Storage Critical Characteristics

International Nuclear Information System (INIS)

BONADIE, E.P.

2000-01-01

This document specifies the critical characteristics for containers procured for Plutonium Finishing Plant's (PFP's) Vault Operations system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to perform its safety function

Engineering report (conceptual design) PFP solution stabilization

Energy Technology Data Exchange (ETDEWEB)

Witt, J.B.

1997-07-17

This Engineering Report (Conceptual Design) addresses remediation of the plutonium-bearing solutions currently in inventory at the Plutonium Finishing Plant (PFP). The recommendation from the Environmental Impact Statement (EIS) is that the solutions be treated thermally and stabilized as a solid for long term storage. For solutions which are not discardable, the baseline plan is to utilize a denitration process to stabilize the solutions prior to packaging for storage.

Engineering report (conceptual design) PFP solution stabilization

International Nuclear Information System (INIS)

Witt, J.B.

1997-01-01

This Engineering Report (Conceptual Design) addresses remediation of the plutonium-bearing solutions currently in inventory at the Plutonium Finishing Plant (PFP). The recommendation from the Environmental Impact Statement (EIS) is that the solutions be treated thermally and stabilized as a solid for long term storage. For solutions which are not discardable, the baseline plan is to utilize a denitration process to stabilize the solutions prior to packaging for storage

Fire hazard analysis for Plutonium Finishing Plant complex

Energy Technology Data Exchange (ETDEWEB)

MCKINNIS, D.L.

1999-02-23

A fire hazards analysis (FHA) was performed for the Plutonium Finishing Plant (PFP) Complex at the Department of Energy (DOE) Hanford site. The scope of the FHA focuses on the nuclear facilities/structures in the Complex. The analysis was conducted in accordance with RLID 5480.7, [DOE Directive RLID 5480.7, 1/17/94] and DOE Order 5480.7A, ''Fire Protection'' [DOE Order 5480.7A, 2/17/93] and addresses each of the sixteen principle elements outlined in paragraph 9.a(3) of the Order. The elements are addressed in terms of the fire protection objectives stated in paragraph 4 of DOE 5480.7A. In addition, the FHA also complies with WHC-CM-4-41, Fire Protection Program Manual, Section 3.4 [1994] and WHC-SD-GN-FHA-30001, Rev. 0 [WHC, 1994]. Objectives of the FHA are to determine: (1) the fire hazards that expose the PFP facilities, or that are inherent in the building operations, (2) the adequacy of the fire safety features currently located in the PFP Complex, and (3) the degree of compliance of the facility with specific fire safety provisions in DOE orders, related engineering codes, and standards.

Collaborative Negotiations: A Successful Approach for Negotiation Compliance Milestones for the transition of the PFP Hanford Nuclear Reservation

International Nuclear Information System (INIS)

HOPKINS, A.M.

2003-01-01

The new approach to negotiations was termed collaborative (win-win) rather than positional (win-lose). Collaborative negotiations were conducted to establish milestones for the decommissioning of the Plutonium Finishing Plant, PFP

Operability test procedure for PFP wastewater sampling facility

International Nuclear Information System (INIS)

Hirzel, D.R.

1995-01-01

Document provides instructions for performing the Operability Test of the 225-WC Wastewater Sampling Station which monitors the discharge to the Treated Effluent Disposal Facility from the Plutonium Finishing Plant. This Operability Test Procedure (OTP) has been prepared to verify correct configuration and performance of the PFP Wastewater sampling system installed in Building 225-WC located outside the perimeter fence southeast of the Plutonium Finishing Plant (PFP). The objective of this test is to ensure the equipment in the sampling facility operates in a safe and reliable manner. The sampler consists of two Manning Model S-5000 units which are rate controlled by the Milltronics Ultrasonic flowmeter at manhole No.C4 and from a pH measuring system with the sensor in the stream adjacent to the sample point. The intent of the dual sampling system is to utilize one unit to sample continuously at a rate proportional to the wastewater flow rate so that the aggregate tests are related to the overall flow and thereby eliminate isolated analyses. The second unit will only operate during a high or low pH excursion of the stream (hence the need for a pH control). The major items in this OTP include testing of the Manning Sampler System and associated equipment including the pH measuring and control system, the conductivity monitor, and the flow meter

HANFORD PLUTONIUM FINISHG PLAN (PFP) COMPLETES PLUTONIUM STABILIZATION KEY SAFETY ISSUES CLOSED

International Nuclear Information System (INIS)

GERBER, M.S.

2004-01-01

A long and intense effort to stabilize and repackage nearly 18 metric tons (MT) of plutonium-bearing leftovers from defense production and nuclear experiments concluded successfully in February, bringing universal congratulations to the Department of Energy's Hanford Site in southeast Washington State. The victorious stabilization and packaging endeavor at the Plutonium Finishing Plant (PFP), managed and operated by prime contractor Fluor Hanford, Inc., finished ahead of all milestones in Hanford's cleanup agreement with regulators, and before deadlines set by the Defense Nuclear Facilities Safety Board (DNFSB), a part of the federal Executive Branch that oversees special nuclear materials. The PFP stabilization and packaging project also completed under budget for its four-year tenure, and has been nominated for a DOE Secretarial Award. It won the Project of the Year Award in the local chapter competition of the Project Management Institute, and is being considered for awards at the regional and national level

DEACTIVATION AND DECOMMISSIONING ENVIRONMENTAL STRATEGY FOR THE PLUTONIUM FINISHING PLANT COMPLEX, HANFORD NUCLEAR RESERVATION

International Nuclear Information System (INIS)

Hopkins, A.M.; Heineman, R.; Norton, S.; Miller, M.; Oates, L.

2003-01-01

Maintaining compliance with environmental regulatory requirements is a significant priority in successful completion of the Plutonium Finishing Plant (PFP) Nuclear Material Stabilization (NMS) Project. To ensure regulatory compliance throughout the deactivation and decommissioning of the PFP complex, an environmental regulatory strategy was developed. The overall goal of this strategy is to comply with all applicable environmental laws and regulations and/or compliance agreements during PFP stabilization, deactivation, and eventual dismantlement. Significant environmental drivers for the PFP Nuclear Material Stabilization Project include the Tri-Party Agreement; the Resource Conservation and Recovery Act of 1976 (RCRA); the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA); the National Environmental Policy Act of 1969 (NEPA); the National Historic Preservation Act (NHPA); the Clean Air Act (CAA), and the Clean Water Act (CWA). Recent TPA negotiation s with Ecology and EPA have resulted in milestones that support the use of CERCLA as the primary statutory framework for decommissioning PFP. Milestones have been negotiated to support the preparation of Engineering Evaluations/Cost Analyses for decommissioning major PFP buildings. Specifically, CERCLA EE/CA(s) are anticipated for the following scopes of work: Settling Tank 241-Z-361, the 232-Z Incinerator, , the process facilities (eg, 234-5Z, 242, 236) and the process facility support buildings. These CERCLA EE/CA(s) are for the purpose of analyzing the appropriateness of the slab-on-grade endpoint Additionally, agreement was reached on performing an evaluation of actions necessary to address below-grade structures or other structures remaining after completion of the decommissioning of PFP. Remaining CERCLA actions will be integrated with other Central Plateau activities at the Hanford site

Walkdown procedure: Seismic adequacy review of safety class 3 ampersand 4 commodities in 2736-Z ampersand ZB buildings at PFP facility

International Nuclear Information System (INIS)

Ocoma, E.C.

1995-01-01

Seismic evaluation of existing safety class (SC) 3 and non-SC 4 commodities at the Plutonium Finishing Plant (PFP) is integrated into an area walkdown program. Field walkdowns of potential PFP seismic deficiencies associated with structural failure and falling will be performed using the DOE SQUG/EPRI methodology. Potential proximity interactions are also addressed. Objective of the walkdown is to qualify as much of the equipment as practical and to identify candidates for further evaluation

Definition and means of maintaining the emergency notification and evacuation system portion of the plutonium finishing plant safety envelope

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

The Emergency Evacuation and Notification System provides information to the Plutonium Finishing Plant (PFP) Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

Radioactive Air Emissions Notice of Construction for the Magnesium Hydroxide Precipitation Process at the Plutonium Finishing Plant (PFP)

International Nuclear Information System (INIS)

JANSKY, M.T.

1999-01-01

The following description and any attachments and references are provided to the Washington State Department of Health (WDOH), Division of Radiation Protection, Air Emissions and Defense Waste (WAC) 246-247, Radiation Protection-Air Emissions. The WAC 246-247-060, ''Applications, registration, and licensing'', states ''This section describes the information requirements for approval to construct, modify, and operate an emission unit. Any NOC requires the submittal of information listed in Appendix A.'' Appendix A (WAC 246-247-1 10) lists the requirements that must be addressed. Additionally, the following description, attachments and references are provided to the US Environmental Protection Agency (EPA) as an NOC, in accordance with Title 40, Code of Federal Regulations (CFR), Part 61, ''National Emission Standards for Hazardous Air Pollutants.'' The information required for submittal to the EPA is specified in 40 CFR 61.07. The potential emissions from this activity are estimated to provide greater than 0.1 millirem per year total effective dose equivalent (TEDE) to the hypothetical offsite maximally exposed individual (MEI), and commencement is needed within a short time. Therefore, this application also is intended to provide notification of the anticipated date of initial startup in accordance with the requirement listed in 40 CFR 61.09(a)(1), and it is requested that approval of this application also will constitute EPA acceptance of this initial startup notification. Written notification of the actual date of initial startup, in accordance with the requirement listed in 40 CFR 61.09(a)(2) will be provided at a later date. This NOC covers the activities associated with the Construction and operation activities involving the magnesium hydroxide precipitation process of plutonium solutions within the Plutonium Finishing Plant (PFP)

Plutonium Finishing Plant Transition Project mission analysis report

International Nuclear Information System (INIS)

Courson, D.B.

1994-01-01

This report defines the mission for the Plutonium Finishing Plant Transition Project (PFPTP) using a systems engineering approach. This mission analysis will be the basis for the functional analysis which will further define and break down the mission statement into all of the detailed functions required to accomplish the mission. The functional analysis is then used to develop requirements, allocate those requirements to functions, and eventually be used to design the system. This report: presents the problem which will be addressed, defines PFP Transition Project, defines the overall mission statement, describes the existing, initial conditions, defines the desired, final conditions, identifies the mission boundaries and external interfaces, identifies the resources required to carry out the mission, describes the uncertainties and risks, and discusses the measures which will be used to determine success

Definition and means of maintaining the emergency notification and evacuation system portion of the plutonium finishing plant safety envelope; TOPICAL

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

The Emergency Evacuation and Notification System provides information to the Plutonium Finishing Plant (PFP) Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

Plutonium Finishing Plant (PFP) Safety Class and Safety Significant Commercial Grade Items (CGI) Critical Characteristic

International Nuclear Information System (INIS)

THOMAS, R.J.

2000-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for use in the Plutonium Finishing Plant as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics of any one item

Evaluation of Need and Location for a Thermogravimetric Analyzer in the Plutonium Finishing Plant (PFP) Materials Stabilization

International Nuclear Information System (INIS)

WILLIS, H.T.

2000-01-01

This plan provides an analysis for locating a TGA to support PFP Thermal Stabilization processes. The scope of this document is to evaluate the need for, and location for, installation of a TGA system as a supplement to the SFE equipment for moisture measurement in pure oxides. A location assessment for the SFE equipment was previously performed (HNF 1999). Based on that assessment, co-location of the TGA system with the SFE system is the preferred option. This would enable thermally stabilized material to be analyzed for residual moisture by either the TGA system or SFE system or both This evaluation considers glovebox locations in the PFP 234-52 Building Analytical Laboratory or operating areas for the installation of the TGA system and it's supporting equipment. This evaluation considers using existing gloveboxes along with an alternative of adding a new glovebox to existing process lines. The location evaluation criteria focuses mainly on glovebox size, with qualitative consideration of relative cost and schedule impacts associated with system implementation, radiological control, and interaction with other laboratory operations and processes. In addition, the possible co-location of a TGA furnace system with the SFE system was considered

Definition and means of maintaining the process vacuum liquid detection interlock systems portion of the PFP safety envelope

International Nuclear Information System (INIS)

LINTHO, J.E.

2003-01-01

The purpose of this document is to record the technical evaluation of the Technical Safety Requirements described in the Plutonium Finishing Plant (PFP) Safety Technical Requirements, HNF-SD-CP-OSR-010/Rev.1, Section 3.1.1, ''Criticality Prevention System.'' This document also defines the Safety Envelope (SE) for the liquid detection interlock system in the Process Vacuum System. The SE is derived FR-om information in the Plutonium Finishing Plant Final Safety Analysis Report (PFP FSAR), HNF-SD-CP-SAR-021, Rev 4, and the Criticality Safety Analysis Report (CSAR) for the 26-inch Hg Vacuum System, WHC-SD-SQA-CSA-20159, Rev 0-A. This document, with its appendices, provides the following: (1) The system functional requirements for determining system operability (Section 3). (2) Evaluations of equipment to determine the safety envelope boundary for the system (Section 4 list of SE boundary drawings). (3) A list of the safety envelope equipment (Appendix B). (4) Functional requirements for the individual safety envelope equipment, including appropriate set points and process parameters (Section 4). (5) A list of the operational and surveillance procedures necessary to operate and maintain the system equipment within the safety envelope (Sections 5 and 6 and Appendix A)

PFP Emergency Lighting Study

International Nuclear Information System (INIS)

BUSCH, M.S.

2000-01-01

NFPA 101, section 5-9 mandates that, where required by building classification, all designated emergency egress routes be provided with adequate emergency lighting in the event of a normal lighting outage. Emergency lighting is to be arranged so that egress routes are illuminated to an average of 1.0 footcandle with a minimum at any point of 0.1 footcandle, as measured at floor level. These levels are permitted to drop to 60% of their original value over the required 90 minute emergency lighting duration after a power outage. The Plutonium Finishing Plant (PFP) has two designations for battery powered egress lights ''Emergency Lights'' are those battery powered lights required by NFPA 101 to provide lighting along officially designated egress routes in those buildings meeting the correct occupancy requirements. Emergency Lights are maintained on a monthly basis by procedure ZSR-12N-001. ''Backup Lights'' are battery powered lights not required by NFPA, but installed in areas where additional light may be needed. The Backup Light locations were identified by PFP Safety and Engineering based on several factors. (1) General occupancy and type of work in the area. Areas occupied briefly during a shiftly surveillance do not require backup lighting while a room occupied fairly frequently or for significant lengths of time will need one or two Backup lights to provide general illumination of the egress points. (2) Complexity of the egress routes. Office spaces with a standard hallway/room configuration will not require Backup Lights while a large room with several subdivisions or irregularly placed rooms, doors, and equipment will require Backup Lights to make egress safer. (3) Reasonable balance between the safety benefits of additional lighting and the man-hours/exposure required for periodic light maintenance. In some plant areas such as building 236-Z, the additional maintenance time and risk of contamination do not warrant having Backup Lights installed in all rooms

System design description PFP thermal stabilization

International Nuclear Information System (INIS)

RISENMAY, H.R.

1998-01-01

The purpose of this document is to provide a system design description and design basis for the Plutonium Finishing P1ant (PFP) Thermal Stabilization project. The sources of material for this project are residues scraped from glovebox floors and materials already stored in vault storage that need further stabilizing to meet the 3013 storage requirements. Stabilizing this material will promote long term storage and reduced worker exposure. This document addresses: function design, equipment, and safety requirements for thermal stabilization of plutonium residues and oxides

Test plan for N2 HEPA filters assembly shop stock used on PFP E4 exhaust system

International Nuclear Information System (INIS)

DICK, J.D.

1999-01-01

At Plutonium Finishing Plant (PFP) and Plutonium Reclamation Facility (PRF) Self-contained HEPA filters, encased in wooden frames and boxes, are installed in the E4 Exhaust Ventilation System to provide confinement of radioactive releases to the environment and confinement of radioactive contamination within designated zones inside the facility. Recently during the routine testing in-leakage was discovered downstream of the Self-contained HEPA filters boxes. This Test Plan describes the approach to conduct investigation of the root causes for the in-leakage of HEPA filters

THE DEACTIVATION, DECONTAMINATION AND DECOMMISSIONING OF THE PLUTONIUM FINISHING PLANT, A FORMER PLUTONIUM PROCESSING FACILITY AT DOE'S HANFORD SITE

International Nuclear Information System (INIS)

CHARBONEAU, S.L.

2006-01-01

The Plutonium Finishing Plant (PFP) was constructed as part of the Manhattan Project during World War II. The Manhattan Project was developed to usher in the use of nuclear weapons to end the war. The primary mission of the PFP was to provide plutonium used as special nuclear material (SNM) for fabrication of nuclear devices for the war effort. Subsequent to the end of World War II, the PFP's mission expanded to support the Cold War effort through plutonium production during the nuclear arms race and later the processing of fuel grade mixed plutonium-uranium oxide to support DOE's breeder reactor program. In October 1990, at the close of the production mission for PFP, a shutdown order was prepared by the Department of Energy (DOE) in Washington,; DC--and issued to the Richland DOE field office. Subsequent to the shutdown order, a team from the Defense Nuclear Facilities Safety Board (DNFSB) analyzed the hazards at PFP associated with the continued storage of certain forms of plutonium solutions and solids. The assessment identified many discrete actions that were required to stabilize the different plutonium forms into stable form and repackage the material in high integrity containers. These actions were technically complicated and completed as part of the PFP nuclear material stabilization project between 1995 and early 2005. The completion of the stabilization project was a necessary first step in deactivating PFP. During stabilization, DOE entered into negotiations with the U.S. Environmental Protection Agency (EPA) and the State of Washington and established milestones for the Deactivation and Decommissioning (DandD) of the PFP. The DOE and its contractor, Fluor Hanford (Fluor), have made great progress in deactivating, decontaminating and decommissioning the PFP at the Hanford Site as detailed in this paper. Background information covering the PFP DandD effort includes descriptions of negotiations with the State of Washington concerning consent

ALARA Design Review for the Resumption of the Plutonium Finishing Plant (PFP) Cementation Process Project Activities

CERN Document Server

Dayley, L

2000-01-01

The requirements for the performance of radiological design reviews are codified in 10CFR835, Occupational Radiation Protection. The basic requirements for the performance of ALARA design reviews are presented in the Hanford Site Radiological Control Manual (HSRCM). The HSRCM has established trigger levels requiring radiological reviews of non-routine or complex work activities. These requirements are implemented in site procedures HNF-PRO-1622 and 1623. HNF-PRO-1622 Radiological Design Review Process requires that ''radiological design reviews [be performed] of new facilities and equipment and modifications of existing facilities and equipment''. In addition, HNF-PRO-1623 Radiological Work Planning Process requires a formal ALARA Review for planned activities that are estimated to exceed 1 person-rem total Dose Equivalent (DE). The purpose of this review is to validate that the original design for the PFP Cementation Process ensures that the principles of ALARA (As Low As Reasonably Achievable) were included...

The Creative Application of Science, Technology and Work Force Innovations to the Decontamination and Decommissioning of the Plutonium Finishing Plant at the Hanford Nuclear Reservation

International Nuclear Information System (INIS)

Charboneau, S.; Klos, B.; Heineman, R.; Skeels, B.; Hopkins, A.

2006-01-01

The Plutonium Finishing Plant (PFP) consists of a number of process and support buildings for handling plutonium. Building construction began in the late 1940's to meet national priorities and became operational in 1950 producing refined plutonium salts and metal for the United States nuclear weapons program The primary mission of the PFP was to provide plutonium used as special nuclear material for fabrication into a nuclear device for the war effort. Subsequent to the end of World War II, the PFP's mission expanded to support the Cold War effort through plutonium production during the nuclear arms race. PFP has now completed its mission and is fully engaged in deactivation, decontamination and decommissioning (D and D). At this time the PFP buildings are planned to be reduced to ground level (slab-on-grade) and the site remediated to satisfy national, Department of Energy (DOE) and Washington state requirements. The D and D of a highly contaminated plutonium processing facility presents a plethora of challenges. PFP personnel approached the D and D mission with a can-do attitude. They went into D and D knowing they were facing a lot of challenges and unknowns. There were concerns about the configuration control associated with drawings of these old process facilities. There were unknowns regarding the location of electrical lines and the condition and contents of process piping containing chemical residues such as strong acids and caustics. The gloveboxes were highly contaminated with plutonium and chemical residues. Most of the glovebox windows were opaque with splashed process chemicals that coated the windows or etched them, reducing visibility to near zero. Visibility into the glovebox was a serious worker concern. Additionally, all the gloves in the gloveboxes were degraded and unusable. Replacing gloves in gloveboxes was necessary to even begin glovebox clean-out. The sheer volume of breathing air needed was also an issue. These and other challenges and PFP

Evaluation of the Magnesium Hydroxide Treatment Process for Stabilizing PFP Plutonium/Nitric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Gerber, Mark A.; Schmidt, Andrew J.; Delegard, Calvin H.; Silvers, Kurt L.; Baker, Aaron B.; Gano, Susan R.; Thornton, Brenda M.

2000-09-28

This document summarizes an evaluation of the magnesium hydroxide [Mg(OH)2] process to be used at the Hanford Plutonium Finishing Plant (PFP) for stabilizing plutonium/nitric acid solutions to meet the goal of stabilizing the plutonium in an oxide form suitable for storage under DOE-STD-3013-99. During the treatment process, nitric acid solutions bearing plutonium nitrate are neutralized with Mg(OH)2 in an air sparge reactor. The resulting slurry, containing plutonium hydroxide, is filtered and calcined. The process evaluation included a literature review and extensive laboratory- and bench-scale testing. The testing was conducted using cerium as a surrogate for plutonium to identify and quantify the effects of key processing variables on processing time (primarily neutralization and filtration time) and calcined product properties.

Assessment of the Plutonium Finishing Plant Criticality Alarm System U.S. Department of Energy Richland Operations Office

International Nuclear Information System (INIS)

NIRIDER, L.T.

2002-01-01

At the request of the Assistant Manager for Safety and Engineering, the U.S. Department of Energy Richland Operations Office (RL) Engineering Support Division, performed an oversight review of the Plutonium Finishing Plant (PFP) nuclear Criticality Alarm System (CAS). The review was conducted to satisfy requirements and agreements associated with Defense Nuclear Facility Safety Board (DNFSB) Recommendation 2000-2, ''Vital Safety Systems.'' The PFP is managed by Fluor Hanford, Inc. for RL. The field assessment and staff interviews were conducted August 12 through August 19,2002. This was a limited scope assessment that consisted of a review of the nuclear CAS operations, maintenance, and compliance with National Consensus Standards Requirements. The main purpose of the assessment was to determine the adequacy of the existing alarm system and its associated infrastructure to support the PFP facility mission through the remaining facility lifetime. The Review Plan was modeled upon Criteria and Review Approach Documents (CRAD) developed for DNFSB Recommendation 2000-2 reviews conducted across the Hanford Site. Concerns regarding component degradation and failure, increasing numbers of occurrence reports associated with the alarm system, and reliability issues were addressed. Additionally, RL performed a review of the engineering aspects of the CAS including the functions of design authorities and aspects of systems engineering. However, the focus of the assessment was on operations, maintenance, and reliability of the CAS, associated procurement practices, adequacy of safety and engineering policies and procedures, safety documentation, and fundamental engineering practices including training, qualification, and systems engineering. This assessment revealed that the PFP CAS and its associated infrastructure, administrative procedures, and conduct of operations are generally effective. There are no imminent criticality safety issues associated with the operation of the

Neutron Measurements At Hanford's Plutonium Finishing Plant

International Nuclear Information System (INIS)

Conrady, Matthew M.; Berg, Randal K.; Scherpelz, Robert I.; Rathbone, Bruce A.

2009-01-01

The Pacific Northwest National Laboratory (PNNL) conducted neutron measurements at Hanford's Plutonium Finishing Plant (PFP). The measurements were performed to evaluate the performance of the Hanford Standard Dosimeter (HSD) and the 8816 TLD component of the Hanford Combination Neutron Dosimeter (HCND) in the neutron fields responsible for worker neutron exposures. For this study, TEPC detectors and multisphere spectrometers were used to measure neutron dose equivalent rate, and multispheres were used to measure average neutron energy. Water-filled phantoms holding Hanford dosimeters were positioned at each measurement location. The phantoms were positioned in the same location where a multisphere measurement was taken and TEPCs were also positioned there. Plant survey meters were also used to measure neutron dose rates at all locations. Three measurement locations were chose near the HC-9B glovebox in room 228A of Building 234-5. The multisphere spectrometers measured average neutron energies in the range of 337 to 555 keV at these locations. Personal dose equivalent, Hp(10)n, as measured by the multisphere and TEPC, ranged from 2.7 to 9.7 mrem/h in the three locations. Effective dose assuming a rotational geometry (EROT) was substantially lower than Hp(10), ranging from 1.3 to 3.6 mrem/h. These values were lower than the reported values from dosimeters exposed on a rotating phantom. Effective dose assuming an AP geometry (EAP) was also substantially lower than Hp(10), ranging from 2.3 to 6.5 mrem/h. These values were lower than the reported values from the dosimeters on slab phantoms. Since the effective dose values were lower than reported values from dosimeters, the dosimeters were shown to be conservative estimates of the protection quantities.

COLLABORATIVE NEGOTIATIONS A SUCCESSFUL APPROACH FOR NEGOTIATING COMPLIANCE MILESTONES FOR THE TRANSITION OF THE PLUTONIUM FINISHING PLANT (PFP), HANFORD NUCLEAR RESERVATION, AND HANFORD, WASHINGTON

International Nuclear Information System (INIS)

Hebdon, J.; Yerxa, J.; Romine, L.; Hopkins, AM; Piippo, R.; Cusack, L.; Bond, R.; Wang, Oliver; Willis, D.

2003-01-01

The Hanford Nuclear Reservation is a former U. S. Department of Energy Defense Production Site. The site is currently listed on the National Priorities List of the Comprehensive Environmental Response Compensation and Liability Act of 1980 (CERCLA) and is undergoing cleanup and environmental restoration. The PFP is a former Plutonium metal production facility. The operating mission of the PFP ended with a DOE Headquarters shutdown letter in October of 1996. Generally, the receipt of a shutdown letter initiates the start of Transition (as the first step of Decommissioning) of a facility. The Hanford site is subject to the Hanford Federal Facilities Compliance Act and Consent Order (HFFCCO), an order on consent signed by the DOE, the U. S. Environmental Protection Agency, (EPA) and the Washington Department of Ecology (WDOE). Under the HFFCCO, negotiations for transition milestones begin within six months after the issuance of a shutdown order. In the case of the PFP, the Nuclear Materials disposition and stabilization activities, a DOE responsibility, were necessary as precursor activities to Transition. This situation precipitated a crisis in the negotiations between the agencies, and formal negotiations initiated in 1997 ended in failure. The negotiations reached impasse on several key regulatory and operational issues. The 1997 negotiation was characterized by a strongly positional style. DOE and the regulatory personnel took hard lines early in the negotiations and were unable to move to resolution of key issues after a year and a half. This resulted in unhappy stakeholders, poor publicity and work delays as well as wounded relationships between DOE and the regulatory community. In the 2000-2001 PFP negotiations, a completely different approach was suggested and eventually initiated: Collaborative Negotiations. The collaborative negotiation style resulted in agreement between the agencies on all key issues within 6 months of initiation. All parties were very

COLLABORATIVE NEGOTIATIONS A SUCCESSFUL APPROACH FOR NEGOTIATING COMPLIANCE MILESTONES FOR THE TRANSITION OF THE PLUTONIUM FINISHING PLANT (PFP), HANFORD NUCLEAR RESERVATION, AND HANFORD, WASHINGTON

Energy Technology Data Exchange (ETDEWEB)

Hebdon, J.; Yerxa, J.; Romine, L.; Hopkins, AM; Piippo, R.; Cusack, L.; Bond, R.; Wang, Oliver; Willis, D.

2003-02-27

The Hanford Nuclear Reservation is a former U. S. Department of Energy Defense Production Site. The site is currently listed on the National Priorities List of the Comprehensive Environmental Response Compensation and Liability Act of 1980 (CERCLA) and is undergoing cleanup and environmental restoration. The PFP is a former Plutonium metal production facility. The operating mission of the PFP ended with a DOE Headquarters shutdown letter in October of 1996. Generally, the receipt of a shutdown letter initiates the start of Transition (as the first step of Decommissioning) of a facility. The Hanford site is subject to the Hanford Federal Facilities Compliance Act and Consent Order (HFFCCO), an order on consent signed by the DOE, the U. S. Environmental Protection Agency, (EPA) and the Washington Department of Ecology (WDOE). Under the HFFCCO, negotiations for transition milestones begin within six months after the issuance of a shutdown order. In the case of the PFP, the Nuclear Materials disposition and stabilization activities, a DOE responsibility, were necessary as precursor activities to Transition. This situation precipitated a crisis in the negotiations between the agencies, and formal negotiations initiated in 1997 ended in failure. The negotiations reached impasse on several key regulatory and operational issues. The 1997 negotiation was characterized by a strongly positional style. DOE and the regulatory personnel took hard lines early in the negotiations and were unable to move to resolution of key issues after a year and a half. This resulted in unhappy stakeholders, poor publicity and work delays as well as wounded relationships between DOE and the regulatory community. In the 2000-2001 PFP negotiations, a completely different approach was suggested and eventually initiated: Collaborative Negotiations. The collaborative negotiation style resulted in agreement between the agencies on all key issues within 6 months of initiation. All parties were very

AN APPROACH TO CHARACTERIZING and EVALUATING ALTERNATIVES FOR THE DECOMMISSIONING OF SUB-GRADE STRUCTURES AT THE PLUTONIUM FINISHING PLANT

International Nuclear Information System (INIS)

HOPKINS, A.M.; KLOS, D.B.

2007-01-01

In 2002, the Richland Operations Office (RL) of the US Department of Energy (DOE), the US Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) developed milestones for transitioning the Plutonium Finishing Plant (PFP) facility to a clean slab-on-grade configuration. These milestones required developing an engineering evaluation/cost analysis (EF/CA) for the facility's sub-grade structures and installations as part of a series of evaluations intended to provide for the transition of the facility to a clean slab-on-grade configuration. In addition to supporting decisions for interim actions, the analyses of sub-grade structures and installations performed through this EE/CA will contribute to the remedial investigation feasibility study(ies) and subsequently to the final records of decision for the relevant operable units responsible for site closure in the 200 West Area of the Hanford Site

Time and Temperature Test Results for PFP Thermal Stabilization Furnaces

International Nuclear Information System (INIS)

COMPTON, J.A.

2000-01-01

The national standard for plutonium storage acceptability (standard DOE-STD-3013-99, generally known as ''the 3013 standard'') has been revised to clarify the requirement for processes that will produce acceptable storage materials. The 3013 standard (Reference 1) now states that ''Oxides shall be stabilized by heating the material in an oxidizing atmosphere to a Material Temperature of at least 950 C (1742 F) for not less than 2 hours.'' The process currently in use for producing stable oxides for storage at the Plutonium Finishing Plant (PFP) heats a furnace atmosphere to 1000 C and holds it there for 2 hours. The temperature of the material being stabilized is not measured directly during this process. The Plutonium Process Support Laboratories (PPSL) were requested to demonstrate that the process currently in use at PFP is an acceptable method of producing stable plutonium dioxide consistently. A spare furnace identical to the production furnaces was set up and tested under varying conditions with non-radioactive surrogate materials. Reference 2 was issued to guide the testing program. The process currently in use at the PFP for stabilizing plutonium-bearing powders was shown to heat all the material in the furnace to at least 950 C for at least 2 hours. The current process will work for (1) relatively pure plutonium dioxide, (2) dioxide powders mixed with up to 20 weight percent magnesium oxide, and (3) dioxide powders with up to 11 weight percent magnesium oxide and 20 weight percent magnesium nitrate hexahydrate. Time and temperature data were also consistent with a successful demonstration for a mixture containing 10 weight percent each of sodium and potassium chloride; however, the molten chloride salts destroyed the thermocouples in the powder and temperature data were unavailable for part of that run. These results assume that the current operating limits of no more than 2500 grams per furnace charge and a powder height of no more than 1.5 inches remain

PFP Wastewater Sampling Facility

International Nuclear Information System (INIS)

Hirzel, D.R.

1995-01-01

This test report documents the results obtained while conducting operational testing of the sampling equipment in the 225-WC building, the PFP Wastewater Sampling Facility. The Wastewater Sampling Facility houses equipment to sample and monitor the PFP's liquid effluents before discharging the stream to the 200 Area Treated Effluent Disposal Facility (TEDF). The majority of the streams are not radioactive and discharges from the PFP Heating, Ventilation, and Air Conditioning (HVAC). The streams that might be contaminated are processed through the Low Level Waste Treatment Facility (LLWTF) before discharging to TEDF. The sampling equipment consists of two flow-proportional composite samplers, an ultrasonic flowmeter, pH and conductivity monitors, chart recorder, and associated relays and current isolators to interconnect the equipment to allow proper operation. Data signals from the monitors are received in the 234-5Z Shift Office which contains a chart recorder and alarm annunciator panel. The data signals are also duplicated and sent to the TEDF control room through the Local Control Unit (LCU). Performing the OTP has verified the operability of the PFP wastewater sampling system. This Operability Test Report documents the acceptance of the sampling system for use

Plutonium finishing plant safety systems and equipment list

International Nuclear Information System (INIS)

Bergquist, G.G.

1995-01-01

The Safety Equipment List (SEL) supports Analysis Report (FSAR), WHC-SD-CP-SAR-021 and the Plutonium Finishing Plant Operational Safety Requirements (OSRs), WHC-SD-CP-OSR-010. The SEL is a breakdown and classification of all Safety Class 1, 2, and 3 equipment, components, or system at the Plutonium Finishing Plant complex

Disposal of TRU Waste from the PFP in pipe overpack containers to WIPP Including New Security Requirements

International Nuclear Information System (INIS)

HOPKINS, A.M.

2003-01-01

The Department of Energy is responsible for the safe management and cleanup of the DOE complex. As part of the cleanup and closure of the Plutonium Finishing Plant (PFP) located on the Hanford site, the nuclear material inventory was reviewed to determine the appropriate disposition path. Based on the nuclear material characteristics, the material was designated for stabilization and packaging for long term storage and transfer to the Savannah River Site, or a decision for discard was made. The discarded material was designated as waste material and slated for disposal to the Waste Isolation Pilot Plant (WIPP). Prior to preparing any residue wastes for disposal at the WIPP, several major activities need to be completed. As detailed a processing history as possible of the material including origin of the waste must be researched and documented. A technical basis for termination of safeguards on the material must be prepared and approved. Utilizing process knowledge and processing history, the material must be characterized, sampling requirements determined, acceptable knowledge package and waste designation completed prior to disposal. All of these activities involve several organizations including the contractor, DOE, state representatives and other regulators such as EPA. At PFP, a process has been developed for meeting the many, varied requirements and successfully used to prepare several residue waste streams including Rocky Flats incinerator ash, hanford incinerator ash and Sand, Slag and Crucible (SS and C) material for disposal. These waste residues are packed into Pipe Overpack Containers for shipment to the WIPP

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

Energy Technology Data Exchange (ETDEWEB)

White, W.F.

1997-05-13

The purpose of this document is to provide the definition and means of maintaining the Safety Envelope (SE) related to the Criticality Alarm System (CAS). This document provides amplification of the Limiting Condition for Operation (LCO) described in the Plutonium Finishing Plant (PFP) Operational Safety Requirements (OSR), WHC-SD-CP-OSR-010, Rev. 0, 1994, Section 3.1.2, Criticality Detectors and Alarms. This document, with its appendices, provides the following: (1) System functional requirements for determining system operability (Section 3); (2) A list of annotated system block diagrams which indicate the safety envelope boundaries (Appendix C); (3) A list of the Safety Class 1 and 2 Safety Envelope (SC-1/2 SE) equipment for input into the Master Component Index (Appendix B); (4) Functional requirements for individual SC-1/2 SE components, including appropriate setpoints and process parameters (Section 6 and Appendix A); (5) A list of the operational, maintenance and surveillance procedures necessary to operate and maintain the SC-1/2 SE components as required by the LCO (Section 6 and Appendix A).

Definition and Means of Maintaining the Criticality Prevention Design Features Portion of the PFP Safety Envelope

International Nuclear Information System (INIS)

RAMBLE, A.L.

2000-01-01

The purpose of this document is to record the technical evaluation of the Operational Safety Requirements described in the Plutonium Finishing Plant Final (PFP) Operational Safety Requirements, WHC-SD-CP-OSR-010. Rev. 0-N , Section 3.1.1, ''Criticality Prevention System.'' This document, with its appendices, provides the following: (1) The results of a review of Criticality Safety Analysis Reports (CSAR), later called Criticality Safety Evaluation Reports (CSER), and Criticality Prevention Specifications (CPS) to determine which equipment or components analyzed in the CSER or CPS are considered as one of the two unlikely, independent, and concurrent changes before a criticality accident is possible. (2) Evaluations of equipment or components to determine the safety boundary for the system (Section 4). (3) A list of essential drawings that show the safety system or component (Appendix A). (4) A list of the safety envelope (SE) equipment (Appendix B). (5) Functional requirements for the individual safety envelope equipment (Sections 3 and 4). (6) A list of the operational and surveillance procedures necessary to maintain the system equipment within the safety envelope (Section 5)

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

International Nuclear Information System (INIS)

White, W.F.

1997-01-01

The purpose of this document is to provide the definition and means of maintaining the Safety Envelope (SE) related to the Criticality Alarm System (CAS). This document provides amplification of the Limiting Condition for Operation (LCO) described in the Plutonium Finishing Plant (PFP) Operational Safety Requirements (OSR), WHC-SD-CP-OSR-010, Rev. 0, 1994, Section 3.1.2, Criticality Detectors and Alarms. This document, with its appendices, provides the following: (1) System functional requirements for determining system operability (Section 3); (2) A list of annotated system block diagrams which indicate the safety envelope boundaries (Appendix C); (3) A list of the Safety Class 1 and 2 Safety Envelope (SC-1/2 SE) equipment for input into the Master Component Index (Appendix B); (4) Functional requirements for individual SC-1/2 SE components, including appropriate setpoints and process parameters (Section 6 and Appendix A); (5) A list of the operational, maintenance and surveillance procedures necessary to operate and maintain the SC-1/2 SE components as required by the LCO (Section 6 and Appendix A)

Environmental-friendly wool fabric finishing by some water plant extracts

Directory of Open Access Journals (Sweden)

Šmelcerović Miodrag

2007-01-01

Full Text Available In this article, environmental-friendly finishing of wool fabric were processed with several water extract plants, such as hibiscus, St. John's wort, and marigold. The plant extracts have good basis in the commercial dyeing of wool, for garment and carpet industry. At the same time, the environmental-friendly finishing by water extracts plants shows very good fastness of the antimicrobial properties and coloration of wool fabric. From an ecological viewpoint, the substitution of chemical dyes with "natural products" may represent not only a strategy to reduce risk and pollutants but also an opportunity for new markets and new businesses, which can expend involving of ecology in trade policy.

Improving Efficiency with 3-D Imaging: Technology Essential in Removing Plutonium Processing Equipment from Plutonium Finishing Plant Gloveboxes

International Nuclear Information System (INIS)

Crow, Stephen H.; Kyle, Richard N.; Minette, Michael J.

2008-01-01

The Plutonium Finishing Plant at Hanford, Washington began operations in 1949 to process plutonium and plutonium products. Its primary mission was to produce plutonium metal, fabricate weapons parts, and stabilize reactive materials. These operations, and subsequent activities, were performed in remote production lines, consisting primarily of hundreds of gloveboxes. Over the years these gloveboxes and processes have been continuously modified. The plant is currently inactive and Fluor Hanford has been tasked to clean out contaminated equipment and gloveboxes from the facility so it can be demolished in the near future. Approximately 100 gloveboxes at PFP have been cleaned out in the past four years and about 90 gloveboxes remain to be cleaned out. Because specific commitment dates for this work have been established with the State of Washington and other entities, it is important to adopt work practices that increase the safety and speed of this effort. The most recent work practice to be adopted by Fluor Hanford D and D workers is the use of 3-D models to improve the efficiency of cleaning out radioactive gloveboxes at the plant. The use of 3-D models has significantly improved the work planning process by providing workers with a clear image of glovebox construction and composition, which is then used to determine cleanout methods and work sequences. The 3-D visual products enhance safety by enabling workers to more easily identify hazards and implement controls. In addition, the ability to identify and target the removal of radiological materials early in the D and D process provides substantial dose reduction for the workers

Plutonium Finishing Plant transition project function analysis report

International Nuclear Information System (INIS)

Lund, D.P.

1995-09-01

The document contains the functions, function definitions, function interfaces, function interface definitions, Input Computer Automated Manufacturing Definition (IDEFO) diagrams, and function hierarchy charts that describe what needs to be performed to deactivate PFP and to continue safe storage, treatment and disposition of Plutonium and High Enriched Uranium

High knee abduction moments are common risk factors for patellofemoral pain (PFP) and anterior cruciate ligament (ACL) injury in girls: is PFP itself a predictor for subsequent ACL injury?

Science.gov (United States)

Myer, Gregory D; Ford, Kevin R; Di Stasi, Stephanie L; Foss, Kim D Barber; Micheli, Lyle J; Hewett, Timothy E

2015-01-01

Identifying risk factors for knee pain and anterior cruciate ligament (ACL) injury can be an important step in the injury prevention cycle. We evaluated two unique prospective cohorts with similar populations and methodologies to compare the incidence rates and risk factors associated with patellofemoral pain (PFP) and ACL injury. The 'PFP cohort' consisted of 240 middle and high school female athletes. They were evaluated by a physician and underwent anthropometric assessment, strength testing and three-dimensional landing biomechanical analyses prior to their basketball season. 145 of these athletes met inclusion for surveillance of incident (new) PFP by certified athletic trainers during their competitive season. The 'ACL cohort' included 205 high school female volleyball, soccer and basketball athletes who underwent the same anthropometric, strength and biomechanical assessment prior to their competitive season and were subsequently followed up for incidence of ACL injury. A one-way analysis of variance was used to evaluate potential group (incident PFP vs ACL injured) differences in anthropometrics, strength and landing biomechanics. Knee abduction moment (KAM) cut-scores that provided the maximal sensitivity and specificity for prediction of PFP or ACL injury risk were also compared between the cohorts. KAM during landing above 15.4 Nm was associated with a 6.8% risk to develop PFP compared to a 2.9% risk if below the PFP risk threshold in our sample. Likewise, a KAM above 25.3 Nm was associated with a 6.8% risk for subsequent ACL injury compared to a 0.4% risk if below the established ACL risk threshold. The ACL-injured athletes initiated landing with a greater knee abduction angle and a reduced hamstrings-to-quadriceps strength ratio relative to the incident PFP group. Also, when comparing across cohorts, the athletes who suffered ACL injury also had lower hamstring/quadriceps ratio than the players in the PFP sample (p15 Nm of knee abduction load

Integrated project management plan for the Plutonium Finishing Plant stabilization and deactivation project

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

This document sets forth the plans, organization, and control systems for managing the PFP Stabilization and Deactivation Project, and includes the top level cost and schedule baselines. The project includes the stabilization of Pu-bearing materials, storage, packaging, and transport of these and other nuclear materials, surveillance and maintenance of facilities and systems relied upon for storage of the materials, and transition of the facilities in the PFP Complex

PFP Interface identification and management planning guide

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The purpose of-this planning guide is to present the process used to identify, document, and control PFP Stabilization and Deactivation Project interfaces. Revisions to this document will include, as attachments, the most recent version of the Project Interface Management List. A preliminary Interface Management List is included in Appendix A. This document is intended be a Project owned management tool. As such, this document will periodically require revisions resulting from improvements of the information, processes, and techniques as now described. For most revisions that suggest improved processes, PFP management approval is all that will be required

Project Management Plan Solution Stabilization

International Nuclear Information System (INIS)

SATO, P.K.

1999-01-01

This plan presents the overall objectives, description, justification and planning for the Plutonium Finishing Plant (PFP) Solutions Stabilization subproject. The intent of this plan is to describe how this project will be managed and integrated with other facility stabilization and deactivation activities. This plan supplements the overall integrated plan presented in the Integrated Project Management Plan (IPMP) for the Plutonium Finishing Plant Stabilization and Deactivation Project, HNF-3617. This project plan is the top-level definitive project management document for the PFP Solution Stabilization subproject. It specifies the technical, schedule, requirements and the cost baselines to manage the execution of the Solution Stabilization subproject. Any deviations to the document must be authorized through the appropriate change control process

Project Management Plan Solution Stabilization

Energy Technology Data Exchange (ETDEWEB)

SATO, P.K.

1999-08-31

This plan presents the overall objectives, description, justification and planning for the Plutonium Finishing Plant (PFP) Solutions Stabilization subproject. The intent of this plan is to describe how this project will be managed and integrated with other facility stabilization and deactivation activities. This plan supplements the overall integrated plan presented in the Integrated Project Management Plan (IPMP) for the Plutonium Finishing Plant Stabilization and Deactivation Project, HNF-3617. This project plan is the top-level definitive project management document for the PFP Solution Stabilization subproject. It specifies the technical, schedule, requirements and the cost baselines to manage the execution of the Solution Stabilization subproject. Any deviations to the document must be authorized through the appropriate change control process.

PFP: Automated prediction of gene ontology functional annotations with confidence scores using protein sequence data.

Science.gov (United States)

Hawkins, Troy; Chitale, Meghana; Luban, Stanislav; Kihara, Daisuke

2009-02-15

Protein function prediction is a central problem in bioinformatics, increasing in importance recently due to the rapid accumulation of biological data awaiting interpretation. Sequence data represents the bulk of this new stock and is the obvious target for consideration as input, as newly sequenced organisms often lack any other type of biological characterization. We have previously introduced PFP (Protein Function Prediction) as our sequence-based predictor of Gene Ontology (GO) functional terms. PFP interprets the results of a PSI-BLAST search by extracting and scoring individual functional attributes, searching a wide range of E-value sequence matches, and utilizing conventional data mining techniques to fill in missing information. We have shown it to be effective in predicting both specific and low-resolution functional attributes when sufficient data is unavailable. Here we describe (1) significant improvements to the PFP infrastructure, including the addition of prediction significance and confidence scores, (2) a thorough benchmark of performance and comparisons to other related prediction methods, and (3) applications of PFP predictions to genome-scale data. We applied PFP predictions to uncharacterized protein sequences from 15 organisms. Among these sequences, 60-90% could be annotated with a GO molecular function term at high confidence (>or=80%). We also applied our predictions to the protein-protein interaction network of the Malaria plasmodium (Plasmodium falciparum). High confidence GO biological process predictions (>or=90%) from PFP increased the number of fully enriched interactions in this dataset from 23% of interactions to 94%. Our benchmark comparison shows significant performance improvement of PFP relative to GOtcha, InterProScan, and PSI-BLAST predictions. This is consistent with the performance of PFP as the overall best predictor in both the AFP-SIG '05 and CASP7 function (FN) assessments. PFP is available as a web service at http://dragon.bio.purdue.edu/pfp

Chemical and Radiochemical Composition of Thermally Stabilized Plutonium Oxide from the Plutonium Finishing Plant Considered as Alternate Feedstock for the Mixed Oxide Fuel Fabrication Facility

International Nuclear Information System (INIS)

Tingey, Joel M.; Jones, Susan A.

2005-01-01

Eighteen plutonium oxide samples originating from the Plutonium Finishing Plant (PFP) on the Hanford Site were analyzed to provide additional data on the suitability of PFP thermally stabilized plutonium oxides and Rocky Flats oxides as alternate feedstock to the Mixed Oxide Fuel Fabrication Facility (MFFF). Radiochemical and chemical analyses were performed on fusions, acid leaches, and water leaches of these 18 samples. The results from these destructive analyses were compared with nondestructive analyses (NDA) performed at PFP and the acceptance criteria for the alternate feedstock. The plutonium oxide materials considered as alternate feedstock at Hanford originated from several different sources including Rocky Flats oxide, scrap from the Remote Mechanical C-Line (RMC) and the Plutonium Reclamation Facility (PRF), and materials from other plutonium conversion processes at Hanford. These materials were received at PFP as metals, oxides, and solutions. All of the material considered as alternate feedstock was converted to PuO2 and thermally stabilized by heating the PuO2 powder at 950 C in an oxidizing environment. The two samples from solutions were converted to PuO2 by precipitation with Mg(OH)2. The 18 plutonium oxide samples were grouped into four categories based on their origin. The Rocky Flats oxide was divided into two categories, low- and high-chloride Rocky Flats oxides. The other two categories were PRF/RMC scrap oxides, which included scrap from both process lines and oxides produced from solutions. The two solution samples came from samples that were being tested at Pacific Northwest National Laboratory because all of the plutonium oxide from solutions at PFP had already been processed and placed in 3013 containers. These samples originated at the PFP and are from plutonium nitrate product and double-pass filtrate solutions after they had been thermally stabilized. The other 16 samples originated from thermal stabilization batches before canning at

Update on the Department of Energy's 1994 plutonium vulnerability assessment for the plutonium finishing plant

International Nuclear Information System (INIS)

HERZOG, K.R.

1999-01-01

A review of the environmental, safety, and health vulnerabilities associated with the continued storage of PFP's inventory of plutonium bearing materials and other SNM. This report re-evaluates the five vulnerabilities identified in 1994 at the PFP that are associated with SNM storage. This new evaluation took a more detailed look and applied a risk ranking process to help focus remediation efforts

PFP Interface identification and management planning guide; TOPICAL

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The purpose of-this planning guide is to present the process used to identify, document, and control PFP Stabilization and Deactivation Project interfaces. Revisions to this document will include, as attachments, the most recent version of the Project Interface Management List. A preliminary Interface Management List is included in Appendix A. This document is intended be a Project owned management tool. As such, this document will periodically require revisions resulting from improvements of the information, processes, and techniques as now described. For most revisions that suggest improved processes, PFP management approval is all that will be required

Honeywell Modular Automation System Computer Software Documentation

International Nuclear Information System (INIS)

STUBBS, A.M.

2000-01-01

The purpose of this Computer Software Document (CSWD) is to provide configuration control of the Honeywell Modular Automation System (MAS) in use at the Plutonium Finishing Plant (PFP). This CSWD describes hardware and PFP developed software for control of stabilization furnaces. The Honeywell software can generate configuration reports for the developed control software. These reports are described in the following section and are attached as addendum's. This plan applies to PFP Engineering Manager, Thermal Stabilization Cognizant Engineers, and the Shift Technical Advisors responsible for the Honeywell MAS software/hardware and administration of the Honeywell System

Plutonium Finishing Plant (PFP) HVAC System Component Index; FINAL

International Nuclear Information System (INIS)

DICK, J.D.

1999-01-01

This document identities the components, design media, procedures and defines the critical characteristics of Commercial Grade Items necessary to ensure the HVAC system provides these functions. This document lists safety class (SC) and safety significant (SS) components for the Heating Ventilation Air Conditioning (HVAC) and specifies the critical characteristics for Commercial Grade Items (CGI), as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item

PFP MICON DCS computer software documentation

Energy Technology Data Exchange (ETDEWEB)

Silvan, G.R.

1996-03-26

This document contains the complete printout of the MICON A/S system configuration used in the Plutonium Finishing Plant. The document is divided into several volumes. Volume 1 covers the workstation display and configuration. All other volumes contain the controller configurations, or programs.

PFP MICON DCS computer software documentation

International Nuclear Information System (INIS)

Silvan, G.R.

1996-01-01

This document contains the complete printout of the MICON A/S system configuration used in the Plutonium Finishing Plant. The document is divided into several volumes. Volume 1 covers the workstation display and configuration. All other volumes contain the controller configurations, or programs

INERT Atmosphere confinement operability test procedure

International Nuclear Information System (INIS)

RISENMAY, H.R.

1999-01-01

This Operability Test Procedure (OTP) provides instructions for testing operability of the Inert Atmosphere Confinement (IAC). The Inert Atmosphere Confinement was designed and built for opening cans of metal items that might have hydrided surfaces. Unreviewed Safety Question (USQ) PFP-97-005 addresses the discovery of suspected plutonium hydride forming on plutonium metal currently stored in the Plutonium Finishing Plant vaults. Plutonium hydride reacts quickly with air, liberating energy. The Inert Atmosphere Confinement was designed to prevent this sudden liberation of energy by opening the material in an inert argon atmosphere instead of the normal glovebox atmosphere. The IAC is located in glovebox HC-21A, room 230B of the 234-5Z Building at the Plutonium Finishing Plant (PFP) in the 200-West Area of the Hanford Site

Honeywell modular automation system computer software documentation

International Nuclear Information System (INIS)

Cunningham, L.T.

1997-01-01

This document provides a Computer Software Documentation for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This system will be used to control new thermal stabilization furnaces in HA-21I

Genotypic and phenotypic diversity in populations of plant-probiotic Pseudomonas spp. colonizing roots

Science.gov (United States)

Picard, Christine; Bosco, Marco

2008-01-01

Several soil microorganisms colonizing roots are known to naturally promote the health of plants by controlling a range of plant pathogens, including bacteria, fungi, and nematodes. The use of theses antagonistic microorganisms, recently named plant-probiotics, to control plant-pathogenic fungi is receiving increasing attention, as they may represent a sustainable alternative to chemical pesticides. Many years of research on plant-probiotic microorganisms (PPM) have indicated that fluorescent pseudomonads producing antimicrobial compounds are largely involved in the suppression of the most widespread soilborne pathogens. Phenotype and genotype analysis of plant-probiotic fluorescent pseudomonads (PFP) have shown considerable genetic variation among these types of strains. Such variability plays an important role in the rhizosphere competence and the biocontrol ability of PFP strains. Understanding the mechanisms by which genotypic and phenotypic diversity occurs in natural populations of PFP could be exploited to choose those agricultural practices which best exploit the indigenous PFP populations, or to isolate new plant-probiotic strains for using them as inoculants. A number of different methods have been used to study diversity within PFP populations. Because different resolutions of the existing microbial diversity can be revealed depending on the approach used, this review first describes the most important methods used for the assessment of fluorescent Pseudomonas diversity. Then, we focus on recent data relating how differences in genotypic and phenotypic diversity within PFP communities can be attributed to geographic location, climate, soil type, soil management regime, and interactions with other soil microorganisms and host plants. It becomes evident that plant-related parameters exert the strongest influence on the genotypic and phenotypic variations in PFP populations.

Plasma-deposited fluorocarbon polymer films on titanium for preventing cell adhesion: a surface finishing for temporarily used orthopaedic implants

Science.gov (United States)

Finke, B.; Testrich, H.; Rebl, H.; Walschus, U.; Schlosser, M.; Zietz, C.; Staehlke, S.; Nebe, J. B.; Weltmann, K. D.; Meichsner, J.; Polak, M.

2016-06-01

The design of a titanium implant surface should ideally support its later application in clinical use. Temporarily used implants have to fulfil requirements different from permanent implants: they should ensure the mechanical stabilization of the bone stock but in trauma surgery they should not be integrated into the bone because they will be removed after fracture healing. Finishing of the implant surface by a plasma-fluorocarbon-polymer (PFP) coating is a possible approach for preventing cell adhesion of osteoblasts. Two different low pressure gas-discharge plasma processes, microwave (MW 2.45 GHz) and capacitively coupled radio frequency (RF 13.56 MHz) plasma, were applied for the deposition of the PFP film using a mixture of the precursor octafluoropropane (C3F8) and hydrogen (H2). The thin films were characterized by x-ray photoelectron spectroscopy, Fourier transform infrared reflection absorption spectroscopy, and water contact angle measurements. Cell culture experiments show that cell adhesion and spreading of MG-63 osteoblasts were clearly reduced or nonexistent on these surfaces, also after 24 h of storage in the cell culture medium. In vivo data demonstrated that the local inflammatory tissue response for the PFP films deposited in MW and RF plasma were comparable to uncoated controls.

A Study on Salt Attack Protection of Structural and Finishing Materials in Power Plant Structures

Energy Technology Data Exchange (ETDEWEB)

Kim, W.B.; Kweon, K.J.; Suh, Y.P.; Nah, H.S.; Lee, K.J.; Park, D.S.; Jo, Y.K. [Korea Electric Power Research Institute, Taejeon (Korea, Republic of)

1997-12-31

This is a final report written by both KEPRI and KICT as a co-operative research titled {sup A} study on Salt Protection of Structural and Finishings in Power Plant Structures{sup .} This study presented the methods to prevent the chloride-induced corrosion of power plant structures through collection and analysis of research datum relating to design, construction and maintenance for the prevention of structural and finishing materials, thru material performance tests for anti-corrosion under many kinds of chloride-induced corrosion environments. As a result, this study proposed the guidelines for design, construction and maintenance of power plant structures due to chloride-induced corrosion. (author). 257 refs., 111 figs., 86 tabs.

A Study on Salt Attack Protection of Structural and Finishing Materials in Power Plant Structures

Energy Technology Data Exchange (ETDEWEB)

Kim, W B; Kweon, K J; Suh, Y P; Nah, H S; Lee, K J; Park, D S; Jo, Y K [Korea Electric Power Research Institute, Taejeon (Korea, Republic of)

1998-12-31

This is a final report written by both KEPRI and KICT as a co-operative research titled {sup A} study on Salt Protection of Structural and Finishings in Power Plant Structures{sup .} This study presented the methods to prevent the chloride-induced corrosion of power plant structures through collection and analysis of research datum relating to design, construction and maintenance for the prevention of structural and finishing materials, thru material performance tests for anti-corrosion under many kinds of chloride-induced corrosion environments. As a result, this study proposed the guidelines for design, construction and maintenance of power plant structures due to chloride-induced corrosion. (author). 257 refs., 111 figs., 86 tabs.

Tank 241-Z-361 Sludge Retrieval and Treatment Alternatives

International Nuclear Information System (INIS)

HAMPTON, B.K.

2000-01-01

The Plutonium Finishing Plant (PFP) Tank 241-Z-361 (Z-361) contains legacy sludge resulting from waste discharges from past missions at PFP. A sketch of the tank is shown in Figure 1. In this view various risers and penetrations are shown along with the sludge level depicted by the horizontal line halfway up the tank, and the ground level depicted by the horizontal line above the tank. The HEPA filter installed for breathing is also shown on one of the risers

Definition and means of maintaining the criticality detectors and alarms portion of the PFP safety envelope

International Nuclear Information System (INIS)

White, W.F.

1997-01-01

The Criticality Alarm System (CAS) provides continuous detection for high radiation (criticality) events and automatically initiates an evacuation signal to affected personnel. The Safety Envelope (SE) for PFP includes the necessary equipment and the required procedures to ensure the CAS is capable of performing its intended function. This document provides the definition and means of maintaining the SE for PFP related to the CAS. This document also identifies and provides a justification for those portions of the CAS excluded from the PFP Safety Envelope

Estimation and characterization of decontamination and decommissioning solid waste expected from the Plutonium Finishing Plant

International Nuclear Information System (INIS)

Millar, J.S.; Pottmeyer, J.A.; Stratton, T.J.

1995-01-01

Purpose of the study was to estimate the amounts of equipment and other materials that are candidates for removal and subsequent processing in a solid waste facility when the Hanford Plutonium Finishing Plant is decontaminated and decommissioned. (Building structure and soil are not covered.) Results indicate that ∼5,500 m 3 of solid waste is expected to result from the decontamination and decommissioning of the Pu Finishing Plant. The breakdown of the volumes and percentages of waste by category is 1% dangerous solid waste, 71% low-level waste, 21% transuranic waste, 7% transuranic mixed waste

In-depth performance evaluation of PFP and ESG sequence-based function prediction methods in CAFA 2011 experiment

Directory of Open Access Journals (Sweden)

Chitale Meghana

2013-02-01

Full Text Available Abstract Background Many Automatic Function Prediction (AFP methods were developed to cope with an increasing growth of the number of gene sequences that are available from high throughput sequencing experiments. To support the development of AFP methods, it is essential to have community wide experiments for evaluating performance of existing AFP methods. Critical Assessment of Function Annotation (CAFA is one such community experiment. The meeting of CAFA was held as a Special Interest Group (SIG meeting at the Intelligent Systems in Molecular Biology (ISMB conference in 2011. Here, we perform a detailed analysis of two sequence-based function prediction methods, PFP and ESG, which were developed in our lab, using the predictions submitted to CAFA. Results We evaluate PFP and ESG using four different measures in comparison with BLAST, Prior, and GOtcha. In addition to the predictions submitted to CAFA, we further investigate performance of a different scoring function to rank order predictions by PFP as well as PFP/ESG predictions enriched with Priors that simply adds frequently occurring Gene Ontology terms as a part of predictions. Prediction accuracies of each method were also evaluated separately for different functional categories. Successful and unsuccessful predictions by PFP and ESG are also discussed in comparison with BLAST. Conclusion The in-depth analysis discussed here will complement the overall assessment by the CAFA organizers. Since PFP and ESG are based on sequence database search results, our analyses are not only useful for PFP and ESG users but will also shed light on the relationship of the sequence similarity space and functions that can be inferred from the sequences.

PFP MICON maintenance manual. Revision 1

International Nuclear Information System (INIS)

Silvan, G.R.

1995-01-01

This manual covers the use of maintenance displays, maintenance procedures, system alarms and common system failures. This manual is intended to supplement the MICON maintenance training not replace it. It also assumes that the user is familiar with the normal operation of the MICON A/S system. The MICON system is a distributed control computer and, among other things, controls the HVAC system for the Plutonium Finishing Plant

Computer software configuration management plan for the Honeywell modular automation system

International Nuclear Information System (INIS)

Cunningham, L.T.

1997-01-01

This document provides a Computer Software management plan for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This type of system will be used to control new thermal stabilization furnaces, a vertical denitrator calciner, and a pyrolysis furnace

Engineering work plan for PFP criticality alarm panel first unit re-build

International Nuclear Information System (INIS)

Clem, W.E.

1994-01-01

This document describes the first step in increasing the quality, reliability, and ease of maintenance of the nine Criticality Alarm Panels (CAP) at PFP. Development control practices and guidelines of WHC-CM-6-1, EP-2.4 and WHC-IP-1026, EPG-2.4 are applied to develop a prototype of a replacement Criticality Alarm Panel (CAP) with facility-use potential. During the development of the prototype CAP, the design requirements of all of PFP's nine CAPs are considered to develop standardized hardware and detailed design drawings that are tailored to PFP maintenance needs. Increased quality and reliability is achieved through quality hardware, proven technology and design techniques, and the use of the Class 1E workmanship standards of WHC-CM-8-1. The end result of the work described by this work plan is a verified/read-to-install replacement for CAP Z4 and verified/released H-2 drawings that are formatted such that they can easily be replicated when producing design drawings for the other eight CAPs

Honeywell Modular Automation System Computer Software Documentation

International Nuclear Information System (INIS)

CUNNINGHAM, L.T.

1999-01-01

This document provides a Computer Software Documentation for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This system will be used to control new thermal stabilization furnaces in HA-211 and vertical denitration calciner in HC-230C-2

A New Property of Conjugated Polymer PFP: Catalytic Degradation of Methylene Blue Aqueous Solution

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

A new property of conjugated polymer poly(furancarbinol-co-phenol)(PFP) was studied.The target copolymer was used as a catalyst after proper heating treatment. And dye methylene blue (MB) could be fully degraded and largely mineralized on PFP, under natural light or even in dark, in a few minutes. Furthermore, the catalytic activity could be preserved after several runs and the catalyst was readily separated. The effect of calcination temperature was also observed.

Preliminary safety analysis report for project 89-GEB-610 Plutonium Finishing Plant instrumentation upgrade. Revision 1

International Nuclear Information System (INIS)

Huber, T.E.

1995-01-01

This document consists of an analysis of the MICON system upgrade. This project shall install a Micon Co. distributed process monitor and control system with Sparc Sun workstation operator interfaces. The Sparc workstations are housed in consoles custom designed to human factors specifications. The distributed control system (DCS) shall have the installed capacity to monitor and control all related instruments and equipment presently connected to the panels in the PFP Power Control Room 321A as listed in the input/output list. This also includes all devices monitored and controlled by the 2736-ZB Allen Bradley programmable logic controller. The system has since assumed the control and monitoring responsibilities for Projects B- 680H ''Low Level Waste Treatment Facility'' and C-031H ''PFP Liquid Effluent Facilities''. Part of the new en's change area in Building 234-5ZA, Room 712, has been remodeled to house two consoles and one supervisor console. Local control units containing the microprocontrollers and the input/output interface circuit boards shall be wired to the instrumentation and controlled equipment. These units communicate with the Sparc workstations via a redundant data communications highway and shall be strategic, throughout the PFP facility. The DCS has already been purchased from Micon Co., located in Houston Texas, presently on site

Facility Effluent Monitoring Plan for the Plutonium Finishing Plant (PFP); FINAL

International Nuclear Information System (INIS)

FRAZIER, T.P.

1999-01-01

A facility effluent monitoring plan is required by the U. S. Department of Energy in DOE Order 5400.1 for any operations that involve hazardous materials and radioactive substances that could impact employee or public safety or the environment. This facility effluent monitoring plan assesses effluent monitoring systems and evaluates whether these systems are adequate to ensure the public health and safety as specified in applicable federal, state, and local requirements. To ensure the long-range integrity of the effluent monitoring systems, an update to this facility effluent monitoring plan is required whenever a new process or operation introduces new hazardous materials or significant radioactive materials. This document is reviewed annually even if there are no operational changes, and is updated, at a minimum, every 3 years

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

Energy Technology Data Exchange (ETDEWEB)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J. [Pacific Northwest Lab., Richland, WA (United States); Nass, R. [Nuclear Fuel Services, Inc. (United States)

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage.

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

International Nuclear Information System (INIS)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J.; Nass, R.

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage

Sludge Stabilization Campaign blend plan

International Nuclear Information System (INIS)

De Vries, M.L.

1994-01-01

This sludge stabilization blend plan documents the material to be processed and the order of processing for the FY95 Sludge Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing sludge. The source of the sludge is residual and glovebox floor sweepings from the production of material at the Plutonium Finishing Plant (PFP). The reactive sludge is currently being stored in various gloveboxes at PFP. There are two types of the plutonium bearing material that will be thermally stabilized in the muffle furnace: Plutonium Reclamation Facility (PRF) sludge and Remote Mechanical C (RMC) Line material

CSER 01-008 Canning of Thermally Stabilized Plutonium Oxide Powder in PFP Glovebox HC-21A

International Nuclear Information System (INIS)

ERICKSON, D.G.

2001-01-01

This document presents the analysis performed to support the canning operation in HC-21A. Most of the actual analysis was performed for the operation in HC-18M and HA-20MB, and is documented in HNF-2707 Rev I a (Erickson 2001a). This document will reference Erickson (2001a) as necessary to support the operation in HC-21A. The plutonium stabilization program at the Plutonium Finishing Plant (PFP) uses heat to convert plutonium-bearing materials into dry powder that is chemically stable for long term storage. The stabilized plutonium is transferred into one of several gloveboxes for the canning process, Gloveboxes HC-18M in Room 228'2, HA-20MB in Room 235B, and HC-21A in Room 230B are to be used for this process. This document presents the analysis performed to support the canning operation in HC-21A. Most of the actual analysis was performed for the operation in HC-I8M and HA-20MB, and is documented in HNF-2707 Rev l a (Erickson 2001a). This document will reference Erickson (2001a) as necessary to support the operation in HC-21A. Evaluation of this operation included normal, base cases, and contingencies. The base cases took the normal operations for each type of feed material and added the likely off-normal events. Each contingency is evaluated assuming the unlikely event happens to the conservative base case. Each contingency was shown to meet the double contingency requirement. That is, at least two unlikely, independent, and concurrent changes in process conditions are required before a criticality is possible

Preliminary safety evaluation for the plutonium stabilization and packaging system

International Nuclear Information System (INIS)

Shapley, J.E.

1997-01-01

This Preliminary Safety Evaluation (PSE) describes and analyzes the installation and operation of the Plutonium Stabilization and Packaging System (SPS) at the Plutonium Finishing Plant (PFP). The SPS is a combination of components required to expedite the safe and timely storage of Plutonium (Pu) oxide. The SPS program will receive site Pu packages, process the Pu for storage, package the Pu into metallic containers, and safely store the containers in a specially modified storage vault. The location of the SPS will be in the 2736- ZB building and the storage vaults will be in the 2736-Z building of the PFP, as shown in Figure 1-1. The SPS will produce storage canisters that are larger than those currently used for Pu storage at the PFP. Therefore, the existing storage areas within the PFP secure vaults will require modification. Other modifications will be performed on the 2736-ZB building complex to facilitate the installation and operation of the SPS

Medicinal plants and finished marketed herbal products used in the treatment of malaria in the Ashanti region, Ghana.

Science.gov (United States)

Komlaga, Gustav; Agyare, Christian; Dickson, Rita Akosua; Mensah, Merlin Lincoln Kwao; Annan, Kofi; Loiseau, Philippe M; Champy, Pierre

2015-08-22

Ethnobotanical survey was performed to document medicinal plants employed in the management of malaria in the Bosomtwe and Sekyere East Districts of the Ashanti Region (Ghana), in comparison with the plant ingredients in herbal antimalarial remedies registered by the Ghana Food and Drug Administration. Two hundred and three (203) herbalists from 33 communities within the two districts were interviewed on medicinal plants they use to manage malaria. A literature search was made to determine already documented plants. In addition, 23 finished marketed herbal products indicated for the management of malaria were identified and their labels examined to find out which of the plants mentioned in our survey were listed as ingredients and whether these products are in anyway regulated. Ninety-eight (98) species of plants were cited for the management of malaria. In comparison with literature citations, 12 (12.2%) species were reported for the management of malaria for the first time and 20 (20.4%) others for the first time in Ghana. Twenty-three (23) finished marketed herbal antimalarial products examined contained aerial or underground parts of 29 of the plants cited in our survey as ingredients. Twenty-two (22) of these products have been registered by the Ghana Food and Drugs Authority, four (4) of which were included in the recommended herbal medicine list for treating malaria in Ghana. This study provides new additions to the inventory of medicinal plants used for the management of malaria and reports the commercial availability and regulation of finished marketed labelled herbal products intended for the treatment of malaria in Ghana. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

1999 Annual Cathodic Protection Survey Report for PFP

International Nuclear Information System (INIS)

BOWMAN, T.J.

2000-01-01

This cathodic protection (CP) report documents the results of the 1999 annual CP survey of the underground piping within PFP property. An annual survey of CP systems is required by Washington Administrative Code (WAC). A spreadsheet to document the 1999 annual survey polarization data is included in this report. Graphs are included to trend the cathodic voltages and the polarization voltages at each test station on PFP property. The trending spans from 1994 to 1999. Graphs are also included to trend voltage and amperage outputs of each rectifier during the annual surveys. During the annual survey, resistance testing between the underground piping was conducted at each test station. The testing showed that all piping (with test leads into the test stations) was continuous with every pipe represented in the test stations. The resistance data is not documented in this report but can be accessed in work package 22-99-01003. During the annual survey, the wiring configurations of anode junction boxes AJB(R45-1) and AJB(45-1) were documented. The sketches can be accessed from the JCS work record of work package 22-99-01003. Analysis, conclusions, and recommendations of the 1999 annual CP survey results are included in this report

Canberra Alpha Sentry Installation Functional Design Criteria (FDC)

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

This document provides the functional design criteria for the installation of the Canberra Alpha Sentry System at selected locations within the Plutonium Finishing Plant (PFP). The equipment being installed is identified by part number in Section 3 and the locations are given in Section 5. The design, procurement and installation are assigned to Fluor Federal Services

Material stabilization characterization management plan

International Nuclear Information System (INIS)

GIBSON, M.W.

1999-01-01

This document presents overall direction for characterization needs during stabilization of SNM at the Plutonium Finishing Plant (PFP). Technical issues for needed data and equipment are identified. Information on material categories and links to vulnerabilities are given. Comparison data on the material categories is discussed to assist in assessing the relative risks and desired processing priority

Honeywell Modular Automation System Computer Software Documentation for the Magnesium Hydroxide Precipitation Process

International Nuclear Information System (INIS)

STUBBS, A.M.

2001-01-01

The purpose of this Computer Software Document (CSWD) is to provide configuration control of the Honeywell Modular Automation System (MAS) in use at the Plutonium Finishing Plant (PFP) for the Magnesium Hydroxide Precipitation Process in Rm 230C/234-5Z. The magnesium hydroxide process control software Rev 0 is being updated to include control programming for a second hot plate. The process control programming was performed by the system administrator. Software testing for the additional hot plate was performed per PFP Job Control Work Package 2Z-00-1703. The software testing was verified by Quality Control to comply with OSD-Z-184-00044, Magnesium Hydroxide Precipitation Process

Facility Operations 1993 fiscal year work plan: WBS 1.3.1

Energy Technology Data Exchange (ETDEWEB)

1992-11-01

The Facility Operations program is responsible for the safe, secure, and environmentally sound management of several former defense nuclear production facilities, and for the nuclear materials in those facilities. As the mission for Facility Operations plants has shifted from production to support of environmental restoration, each plant is making a transition to support the new mission. The facilities include: K Basins (N Reactor fuel storage); N Reactor; Plutonium-Uranium Reduction Extraction (PUREX) Plant; Uranium Oxide (UO{sub 3}) Plant; 300 Area Fuels Supply (N Reactor fuel supply); Plutonium Finishing Plant (PFP).

Facility Operations 1993 fiscal year work plan: WBS 1.3.1

International Nuclear Information System (INIS)

1992-11-01

The Facility Operations program is responsible for the safe, secure, and environmentally sound management of several former defense nuclear production facilities, and for the nuclear materials in those facilities. As the mission for Facility Operations plants has shifted from production to support of environmental restoration, each plant is making a transition to support the new mission. The facilities include: K Basins (N Reactor fuel storage); N Reactor; Plutonium-Uranium Reduction Extraction (PUREX) Plant; Uranium Oxide (UO 3 ) Plant; 300 Area Fuels Supply (N Reactor fuel supply); Plutonium Finishing Plant (PFP)

Results of dilution studies with waste from tank 241-AN-104

International Nuclear Information System (INIS)

HERTING, D.L.

1999-01-01

This report documents the completion of the B and W Hanford Company functional and Safety Review Board reviews and the Fluor Daniel Hanford review for the Plutonium Finishing Plant (PFP) Final Safety Analysis Report (FSAR), HNF-SD-CP-SAR-021, Revision 1. The reviews for the FSAR were conducted during the period from December 9, 1998 to January 14, 1999

Functional Design Criteria - plutonium stabilization and handling (PUSH) project W-460

International Nuclear Information System (INIS)

NELSON, D.W.

1999-01-01

This Functional Design Criteria (FDC) contains information to guide the design of the Stabilization and Packaging Equipment necessary to oxidize and package the remaining plutonium-bearing Special Nuclear Materials (SNM) currently in the Plutonium Finishing Plant (PFP) inventory. The FDC also guides the design of vault modifications to allow storage of 3013 packages of stabilized SNM for up to 50 years

Functional Design Criteria plutonium stabilization and handling (PUSH) project W-460

Energy Technology Data Exchange (ETDEWEB)

NELSON, D.W.

1999-09-02

This Functional Design Criteria (FDC) contains information to guide the design of the Stabilization and Packaging Equipment necessary to oxidize and package the remaining plutonium-bearing Special Nuclear Materials (SNM) currently in the Plutonium Finishing Plant (PFP) inventory. The FDC also guides the design of vault modifications to allow storage of 3013 packages of stabilized SNM for up to 50 years.

Plutonium Finishing Plant (PFP) Generalized Geometry Holdup Calculations and Total Measurement Uncertainty

International Nuclear Information System (INIS)

Keele, B.D.

2005-01-01

A collimated portable gamma-ray detector will be used to quantify the plutonium content of items that can be approximated as a point, line, or area geometry with respect to the detector. These items can include ducts, piping, glove boxes, isolated equipment inside of gloveboxes, and HEPA filters. The Generalized Geometry Holdup (GGH) model is used for the reduction of counting data. This document specifies the calculations to reduce counting data into contained plutonium and the associated total measurement uncertainty.

Current situation of the project finishing of the building of 3 and 4 block of the nuclear power plant Mochovce

International Nuclear Information System (INIS)

Niznan, S.

2005-01-01

In the contribution there is the basic information mentioned about history of building and the current situation at the finishing of the building of 3 and 4 block of the Nuclear Power Plant Mochovce with the use of project digitization. Further on the contribution shows what kinds of supporting material has been elaborated, what kind of decisions have been issued to the finishing of the building, way of financing and also the assumption of investment return under the defined conditions. An orientation time schedule of the finishing of the building and the crucial steps for its security are presented in the conclusion

Literature Review: Crud Formation at the Liquid/Liquid Interface of TBP-Based Solvent-Extraction Processes

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Casella, Amanda J.

2016-09-30

This report summarizes the literature reviewed on crud formation at the liquid:liquid interface of solvent extraction processes. The review is focused both on classic PUREX extraction for industrial reprocessing, especially as practiced at the Hanford Site, and for those steps specific to plutonium purification that were used at the Plutonium Reclamation Facility (PRF) within the Plutonium Finishing Plant (PFP) at the Hanford Site.

PFP Commercial Grade Food Pack Cans for Plutonium Handling and Storage Critical Characteristics

International Nuclear Information System (INIS)

BONADIE, E.P.

1999-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for PFP's Vault Operations system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to perform its safety function

The Tiger Team Process in the Rebaselining of the Plutonium Finishing Plant (PFP)

International Nuclear Information System (INIS)

BAILEY, R.W.

2000-01-01

This paper will describe the integrated, teaming approach and planning process utilized by the Tiger Team in the development of the IPMP. This paper will also serve to document the benefits derived from this implementation process

Pilot-industrial plant for radiation-chemical finishing of textiles

International Nuclear Information System (INIS)

Burov, V.K.; Vanyushkin, B.M.; Voskoboev, A.E.

1976-01-01

A pilot technological radiational-chemical line for liquid-phase radiational-chemical finish of fabrics is described, which is being mounted at the Glukhov cotton group of enterprises now. It is designed primarily for the anti-microbe finish of cotton fabrics by grafting copper polyacrylate. The technological scheme is built on the principle of direct (combined) irradiation of the fabric impregnated by a monomer solution. Graft of the monomer to the fabric is performed by the radiational method. As source of radiation, an electron accelerator with the beam power of 0.4-0.7 Mev and with a biological protection has been employed. Depending on the thickness of the material irradiated and irradiation conditions, the fabric drive mechanism permits to change a number of irradiated fabric layers from 1 to 9 and by this to utilize in the most complete manner the energy of the accelerated electron beam. The nominal width of the irradiated material is 1000 m, the transportation velocity can vary in the range from 10 through 100 m/min. The radiational-chemical method of fabric finish is economical, highly productive and easily controllable

Treatment of Wastewater from Electroplating, Metal Finishing and Printed Circuit Board Manufacturing. Operation of Wastewater Treatment Plants Volume 4.

Science.gov (United States)

California State Univ., Sacramento. Dept. of Civil Engineering.

One of four manuals dealing with the operation of wastewater plants, this document was designed to address the treatment of wastewater from electroplating, metal finishing, and printed circuit board manufacturing. It emphasizes how to operate and maintain facilities which neutralize acidic and basic waters; treat waters containing metals; destroy…

CSER 00-006 Storage of Plutonium Residue Containers in 55 Gallon Drums at the PFP

Energy Technology Data Exchange (ETDEWEB)

DOBBIN, K.D.

2000-05-24

This criticality safety evaluation report (CSER) provides the required limit set and controls for safe transit and storage of these drums in the 234-5Z Building at the PFP. A mass limit of 200 g of plutonium or fissile equivalent per drum is acceptable

Computer-aided dispatching system design specification

Energy Technology Data Exchange (ETDEWEB)

Briggs, M.G.

1997-12-16

This document defines the performance requirements for a graphic display dispatching system to support Hanford Patrol Operations Center. This document reflects the as-built requirements for the system that was delivered by GTE Northwest, Inc. This system provided a commercial off-the-shelf computer-aided dispatching system and alarm monitoring system currently in operations at the Hanford Patrol Operations Center, Building 2721E. This system also provides alarm back-up capability for the Plutonium Finishing Plant (PFP).

Computer-aided dispatching system design specification

International Nuclear Information System (INIS)

Briggs, M.G.

1997-01-01

This document defines the performance requirements for a graphic display dispatching system to support Hanford Patrol Operations Center. This document reflects the as-built requirements for the system that was delivered by GTE Northwest, Inc. This system provided a commercial off-the-shelf computer-aided dispatching system and alarm monitoring system currently in operations at the Hanford Patrol Operations Center, Building 2721E. This system also provides alarm back-up capability for the Plutonium Finishing Plant (PFP)

Definition and means of maintaining the emergency notification and evacuation system portion of the Plutonium Finishing Plant safety envelope

International Nuclear Information System (INIS)

White, W.F.

1997-01-01

The Emergency Evacuation and Notification System provides information to the PFP Building Emergency Director to assist in determining appropriate emergency response, notifies personnel of the required response, and assists in their response. The report identifies the equipment in the Safety Envelope (SE) for this System and the Administrative, Maintenance, and Surveillance Procedures used to maintain the SE Equipment

Calculation note - Consequences of a fire in the sorting and repackaging glovebox in room 636 of bldg 2736-ZB - Plutonium Finishing Plant

International Nuclear Information System (INIS)

JOHNSON, L.E.

1999-01-01

This Calculation Note provides a conservative estimate of the grams of plutonium released from Building 2736-ZB of the Plutonium Finishing Plant as a result of a fire within Glovebox 636, without consideration of mitigation

Artificial intelligence and distance learning philosophy in support of PfP mandate

OpenAIRE

Antoliš, Krunoslav

2003-01-01

Computers have long been utilised in the legal environment. The main use of computers however, has merely been to automate office tasks. More exciting is the prospect of using artificial intelligence (AI) technology to create computers that can emulate the substantive legal jobs performed by lawyers, to create computers that can autonomously reason with the law to determine legal solutions, for example: structuring and support of Partnership for Peace (PfP) mandate. Such attempts have not bee...

SAFETY STUDIES TO MEASURE EXOTHERMIC REACTIONS OF SPENT PLUTONIUM DECONTAMINATION CHEMICALS USING WET AND DRY DECONTAMINATION METHODS

International Nuclear Information System (INIS)

HOPKINS, A.M.; JACKSON, G.W.; MINETTE, M.; EWALT, J.; COOPER, T.; SCOTT, P.; JONES, S.; SCHEELEY, R.

2005-01-01

The Plutonium Finishing Plant (PFP) at the Hanford site in Eastern Washington is currently being decommissioned by Fluor Hanford. Chemicals being considered for dccontamination of gloveboxes in PFP include cerium (IV) nitrate in a nitric acid solution, and proprietary commercial solutions that include acids and sequestering agents. Aggressive chemicals are commonly used to remove transuranic contaminants from process equipment to allow disposal of the equipment as low level waste. Fluor's decontamination procedure involves application of chemical solutions as a spray on the contaminated surfaces, followed by a wipe-down with rags. Alternatively, a process of applying oxidizing Ce IV ions contained in a gel matrix and vacuuming a dry gel material is being evaluated. These processes effectively transfer the transuranic materials to rags or a gel matrix which is then packaged as TRU waste and disposed

Properties of the malarial proteins Pf2, Pf9 and PfP0, which support ...

Indian Academy of Sciences (India)

Properties of the malarial proteins Pf2, Pf9 and PfP0, which support their roles as immune targets. Antibodies raised to each of these proteins (or purified from immune adults) inhibit the growth of Plasmodium falciparum at the red cell invasion step. The proteins are localized on the parasite cell surface. Each protein is ...

Westinghouse Hanford Company special nuclear material vault storage study

International Nuclear Information System (INIS)

Borisch, R.R.

1996-01-01

Category 1 and 2 Special Nuclear Materials (SNM) require storage in vault or vault type rooms as specified in DOE orders 5633.3A and 6430.1A. All category 1 and 2 SNM in dry storage on the Hanford site that is managed by Westinghouse Hanford Co (WHC) is located in the 200 West Area at Plutonium Finishing Plant (PFP) facilities. This document provides current and projected SNM vault inventories in terms of storage space filled and forecasts available space for possible future storage needs

Project Execution Plan Project 98L-EWW-460 Plutonium Stabilization and Handling DOE 98-D-453

International Nuclear Information System (INIS)

MCGRATH, G.M.

2000-01-01

This Project Execution Plan (PEP) describes the management methods and responsibilities of the project participants. Project W-460 is sufficiently large to warrant a stand alone PEP. This project specific PEP describes the relationships and responsibilities of the project team and identifies the technical, schedule, and cost baselines that have been established for the project. The Department of Energy (DOE), Hanford Works (Hanford), at Richland, Wa. currently does not have a system capable of stabilizing or packaging large quantities of plutonium-bearing solids to meet DOE technical standard DOE-STD-3013-99. This project will allow Hanford to meet this standard by installing stabilization and packaging equipment (SPE). The SPE is capable of stabilizing and packaging the current inventory of greater than 30 percent plutonium-bearing materials currently stored in the Plutonium Finishing Plant's (PFP) vaults into 3013 storage containers. The scope of this project is to procure and install the SPE via a Hanford contract and coordination with the Savannah River Site. In addition, the project will modify PFP vaults and upgrade the PFP Laboratory measurement systems. The Facility infrastructure will be modified to support the new SPE system and the new standardized storage container configuration

Project Execution Plan Project 98L-EWW-460 Plutonium Stabilization and Handling DOE 98-D-453

Energy Technology Data Exchange (ETDEWEB)

HOLSTEIN, W.A.

1999-08-01

This Project Execution Plan (PEP) describes the management methods and responsibilities of the project participants. Project W-460 is sufficiently large to warrant a stand alone PEP. This project specific PEP describes the relationships and responsibilities of the project team and identifies the technical, schedule, and cost baselines that have been established for the project. The Department of Energy (DOE), Hanford Works (Hanford), at Richland Wa. currently does not have a system capable of stabilizing or packaging large quantities of plutonium-bearing solids to meet DOE technical standard DOE-STD-3013-96. This project will allow Hanford to meet this standard by installing stabilization and packaging equipment (SPE). The SPE is capable of stabilizing and packaging the current inventory of greater than 50 percent plutonium-bearing materials currently stored in the Plutonium Finishing Plant's (PFP) vaults into 3013 storage containers. The scope of this project is to procure and install the SPE via a Hanford contract and coordination with the Savannah River Site. In addition, the project will modify PFP vaults and upgrade the PFP Laboratory measurement systems. The Facility infrastructure will be modified to support the new SPE system and the new standardized storage container configuration.

Project Execution Plan Project 98L-EWW-460 Plutonium Stabilization and Handling DOE 98-D-453

Energy Technology Data Exchange (ETDEWEB)

MCGRATH, G.M.

2000-06-21

This Project Execution Plan (PEP) describes the management methods and responsibilities of the project participants. Project W-460 is sufficiently large to warrant a stand alone PEP. This project specific PEP describes the relationships and responsibilities of the project team and identifies the technical, schedule, and cost baselines that have been established for the project. The Department of Energy (DOE), Hanford Works (Hanford), at Richland, Wa. currently does not have a system capable of stabilizing or packaging large quantities of plutonium-bearing solids to meet DOE technical standard DOE-STD-3013-99. This project will allow Hanford to meet this standard by installing stabilization and packaging equipment (SPE). The SPE is capable of stabilizing and packaging the current inventory of greater than 30 percent plutonium-bearing materials currently stored in the Plutonium Finishing Plant's (PFP) vaults into 3013 storage containers. The scope of this project is to procure and install the SPE via a Hanford contract and coordination with the Savannah River Site. In addition, the project will modify PFP vaults and upgrade the PFP Laboratory measurement systems. The Facility infrastructure will be modified to support the new SPE system and the new standardized storage container configuration.

Nuclear criticality safety: general. 6. Application of Fixed Neutron Absorbers in the New Hanford PFP Horizontal Rack Design

International Nuclear Information System (INIS)

Lan, J.S.; Miller, E.M.; Toffer, H.; Mo, B.S.

2001-01-01

The Hanford Plutonium Finishing Plant (PFP) is currently in a waste cleanup and plutonium stabilization mode. Plutonium-bearing materials are processed through thermal treatment, creating forms of oxides suitable for long-term storage. Stabilized materials at PFP are stored in a variety of cans such as the bag-less transfer cans (BTCs), which are ultimately contained in the U.S. Department of Energy (DOE) 3013 can; both cans are larger than previously used plutonium storage containers and hold more plutonium. To compensate for the increased plutonium loadings, added engineered safety features were considered in the storage facilities. The vaults in PFP, subdivided into concrete-walled cubicles, will contain both new and older cans. The DOE 3013 and BTC cans may be loaded with up to 4.4 kg of plutonium as a compound (mostly oxide). New racks that store cans horizontally are being constructed to hold both new and older containers. The loading objective is to accommodate 70 kg of plutonium per cubicle. Two design analysis approaches for the new racks were considered. The first approach incorporated neutron absorption provided by the structural materials of the rack and the cans in determining a safe configuration. A rack loading arrangement was determined as shown in Fig. 1 and specified in Table I. This approach provides compliance with criticality control requirements; however, added administrative controls were needed to accommodate a sufficient number of cans in specific locations to achieve 70 kg of plutonium per cubicle. The 4.4-kg plutonium container can be placed only in predetermined locations. The second approach evaluated the addition of a fixed neutron absorber plate along the back wall of the cubicle (Fig. 1). The location of the special plate facilitates installation of the racks and provides additional criticality safety margin beyond the first approach. Its presence permits loading of racks with up to 4.4-kg plutonium cans in any storage locations

Addendum 2 to CSER 79-002: Extension of the 150 gram fissile limit used in room 187 of PFP

International Nuclear Information System (INIS)

Friar, D.E.

1994-01-01

The PFP operating organization requests that the limit set permitting 150 grams fissile be extended to the Hoods 4 and 5 of Room 187. The request for the limit change is explained in the attached request for analysis

Plutonium stabilization and handling quality assurance program plan

International Nuclear Information System (INIS)

Weiss, E.V.

1998-01-01

This Quality Assurance Program Plan (QAPP) identifies project quality assurance requirements for all contractors involved in the planning and execution of Hanford Site activities for design, procurement, construction, testing and inspection for Project W-460, Plutonium Stabilization and Handling. The project encompasses procurement and installation of a Stabilization and Packaging System (SPS) to oxidize and package for long term storage remaining plutonium-bearing special nuclear materials currently in inventory at the Plutonium Finishing Plant (PFP), and modification of vault equipment to allow storage of resulting packages of stabilized SNM

The chemistry of tributyl phosphate at elevated temperatures in the Plutonium Finishing Plant Process Vessels

International Nuclear Information System (INIS)

Barney, G.S.; Cooper, T.D.

1994-01-01

Potentially violent chemical reactions of the tributyl phosphate solvent used by the Plutonium Finishing Plant at the Hanford Site were investigated. There is a small probability that a significant quantity of this solvent could be accidental transferred to heated process vessels and react there with nitric acid or plutonium nitrate also present in the solvent extraction process. The results of laboratory studies of the reactions show that exothermic oxidation of tributyl phosphate by either nitric acid or actinide nitrates is slow at temperatures expected in the heated vessels. Less than four percent of the tributyl phosphate will be oxidized in these vented vessels at temperatures between 125 degrees C and 250 degrees C because the oxidant will be lost from the vessels by vaporization or decomposition before the tributyl phosphate can be extensively oxidized. The net amounts of heat generated by oxidation with concentrated nitric acid and with thorium nitrate (a stand-in for plutonium nitrate) were determined to be about -150 and -220 joules per gram of tributyl phosphate initially present, respectively. This is not enough heat to cause violent reactions in the vessels. Pyrolysis of the tributyl phosphate occurred in these mixtures at temperatures of 110 degrees C to 270 degrees C and produced mainly 1-butene gas, water, and pyrophosphoric acid. Butene gas generation is slow at expected process vessel temperatures, but the rate is faster at higher temperatures. At 252 degrees C the rate of butene gas generated was 0.33 g butene/min/g of tributyl phosphate present. The measured heat absorbed by the pyrolysis reaction was 228 J/g of tributyl phosphate initially present (or 14.5 kcal/mole of tributyl phosphate). Release of flammable butene gas into process areas where it could ignite appears to be the most serious safety consideration for the Plutonium Finishing Plant

The chemistry of tributyl phosphate at elevated temperatures in the Plutonium Finishing Plant Process Vessels

Energy Technology Data Exchange (ETDEWEB)

Barney, G.S.; Cooper, T.D.

1994-06-01

Potentially violent chemical reactions of the tributyl phosphate solvent used by the Plutonium Finishing Plant at the Hanford Site were investigated. There is a small probability that a significant quantity of this solvent could be accidental transferred to heated process vessels and react there with nitric acid or plutonium nitrate also present in the solvent extraction process. The results of laboratory studies of the reactions show that exothermic oxidation of tributyl phosphate by either nitric acid or actinide nitrates is slow at temperatures expected in the heated vessels. Less than four percent of the tributyl phosphate will be oxidized in these vented vessels at temperatures between 125{degrees}C and 250{degrees}C because the oxidant will be lost from the vessels by vaporization or decomposition before the tributyl phosphate can be extensively oxidized. The net amounts of heat generated by oxidation with concentrated nitric acid and with thorium nitrate (a stand-in for plutonium nitrate) were determined to be about -150 and -220 joules per gram of tributyl phosphate initially present, respectively. This is not enough heat to cause violent reactions in the vessels. Pyrolysis of the tributyl phosphate occurred in these mixtures at temperatures of 110{degrees}C to 270{degrees}C and produced mainly 1-butene gas, water, and pyrophosphoric acid. Butene gas generation is slow at expected process vessel temperatures, but the rate is faster at higher temperatures. At 252{degrees}C the rate of butene gas generated was 0.33 g butene/min/g of tributyl phosphate present. The measured heat absorbed by the pyrolysis reaction was 228 J/g of tributyl phosphate initially present (or 14.5 kcal/mole of tributyl phosphate). Release of flammable butene gas into process areas where it could ignite appears to be the most serious safety consideration for the Plutonium Finishing Plant.

Stabilizing plutonium materials at Hanford: systems engineering for PFP transition project effort on DNFSB 94-1

Energy Technology Data Exchange (ETDEWEB)

Huber, T.E., Westinghouse Hanford

1996-07-02

This report discusses the basic objectives of the stabilization and packaging activities at the Plutonium Finishing Plant that satisfy the Defense Nuclear Facility Safety Board Recommendation 94-1 by transforming the plutonium materials at hanford into forms or conditions which are suitable for safe storage to appropriate storage criteria; or discard that meets appropriate waste acceptance criteria.

Radioactive waste management plan for the PBMR (Pty) Ltd fuel plant

International Nuclear Information System (INIS)

Makgae, Mosidi E.

2009-01-01

The Pebble Bed Modular Reactor (Pty) Ltd Fuel Plant (PFP) radioactive waste management plan caters for waste from generation, processing through storage and possible disposal. Generally, the amount of waste that will be generated from the PFP is Low and Intermediate Level Waste. The waste management plan outlines all waste streams and the management options for each stream. It also discusses how the Plant has been designed to ensure radioactive waste minimisation through recycling, recovery, reuse, treatment before considering disposal. Compliance to the proposed plan will ensure compliance with national legislative requirements and international good practice. The national and the overall waste management objective is to ensure that all PFP wastes are managed appropriately by utilising processes that minimize, reduce, recover and recycle without exposing employees, the public and the environment to unacceptable impacts. Both International Atomic Energy Agency (IAEA) and Department of Minerals and Energy (DME) principles act as a guide in the development of the strategy in order to ensure international best practice, legal compliance and ensuring that the impact of waste on employees, environment and the public is as low as reasonably achievable. The radioactive waste classification system stipulated in the Radioactive Waste Management Policy and Strategy 2005 will play an important role in classifying radioactive waste and ensuring that effective management is implemented for all waste streams, for example gaseous, liquid or solid wastes.

Peak pressures from hydrogen deflagrations in the PFP thermal stabilization glovebox

International Nuclear Information System (INIS)

Van Keuren, J.C.

1998-01-01

This document describes the calculations of the peak pressures due to hydrogen deflagrations in the glovebox used for thermal stabilization (glovebox HC-21A) in PFP. Two calculations were performed. The first considered the burning of hydrogen released from a 7 inch Pu can in the Inert Atmosphere Confinement (IAC) section of the glovebox. The peak pressure increase was 12400 Pa (1.8 psi). The second calculation considered burning of the hydrogen from 25 g of plutonium hydride in the airlock leading to the main portion of the glovebox. Since the glovebox door exposes most of the airlock when open, the deflagration was assumed to pressurize the entire glovebox. The peak pressure increase was 3860 Pa (0.56 psi)

The PBMR fuel plant: Proven technology in an advanced safety environment

International Nuclear Information System (INIS)

Braehler, G.; Froschauer, K.; Welbers, P.; Boyes, D.

2008-01-01

The PBMR Fuel Plant (PFP), to be constructed at the Pelindaba site near Johannesburg will fuel the first South African Pebble Bed Modular Reactor. The qualification of the PBMR fuel shall be based on past experience with fuel which was produced in the German NUKEM/HOBEG plant and irradiated in the German AVR reactor. Accordingly, the PFP must produce the same fuel as the German plant did, and consequently, the design of the PFP has in essence to be a copy of the NUKEM/HOBEG plant. As a reminder this plant had been operated in accordance with the German regulatory rules which were defined in the years 1970/80. Since then, the requirements with regard to radiological protection, criticality safety and emission control have been significantly tightened, and of course the PFP must be designed in accordance with the most advanced international norms and standards. The implications which follow from these two potentially conflicting requirements, as defined above, are highlighted, and technical solutions are presented. Hence, the change from administrative criticality safety control to technical control, i.e. the application of safe geometry as far as possible. and the introduction of technical solutions for the remaining safe mass regime will be described. A lot of equipment in the Kernel area and in the recycling areas needed to be redesigned in safe geometry. The sensitive processes for Kernel Calcining, for the Coating and the Over-coating remain under safe mass regime, but the safety against criticality is completely independent from staff activities and based on technical measures. A new concept for safe storage of large volumes of Uranium-containing liquids has been developed. Also, the change from relatively open handling of Uranium to the application of containment enclosures wherever release of radioactivity into the room atmosphere is possible, will be addressed. This change required redesign of all process steps requiring the handling of dry Uranium oxides

Functional enrichment analyses and construction of functional similarity networks with high confidence function prediction by PFP

Directory of Open Access Journals (Sweden)

Kihara Daisuke

2010-05-01

Full Text Available Abstract Background A new paradigm of biological investigation takes advantage of technologies that produce large high throughput datasets, including genome sequences, interactions of proteins, and gene expression. The ability of biologists to analyze and interpret such data relies on functional annotation of the included proteins, but even in highly characterized organisms many proteins can lack the functional evidence necessary to infer their biological relevance. Results Here we have applied high confidence function predictions from our automated prediction system, PFP, to three genome sequences, Escherichia coli, Saccharomyces cerevisiae, and Plasmodium falciparum (malaria. The number of annotated genes is increased by PFP to over 90% for all of the genomes. Using the large coverage of the function annotation, we introduced the functional similarity networks which represent the functional space of the proteomes. Four different functional similarity networks are constructed for each proteome, one each by considering similarity in a single Gene Ontology (GO category, i.e. Biological Process, Cellular Component, and Molecular Function, and another one by considering overall similarity with the funSim score. The functional similarity networks are shown to have higher modularity than the protein-protein interaction network. Moreover, the funSim score network is distinct from the single GO-score networks by showing a higher clustering degree exponent value and thus has a higher tendency to be hierarchical. In addition, examining function assignments to the protein-protein interaction network and local regions of genomes has identified numerous cases where subnetworks or local regions have functionally coherent proteins. These results will help interpreting interactions of proteins and gene orders in a genome. Several examples of both analyses are highlighted. Conclusion The analyses demonstrate that applying high confidence predictions from PFP

Analysis Of The Reactivity Of Radpro Solution With Cotton Rags

International Nuclear Information System (INIS)

Marusich, R.M.

2009-01-01

Rags containing RadPro(reg s ign) solution will be generated during the decontamination of the Plutonium Finishing Plant (PFP). Under normal conditions, the rags will be neutralized with sodium carbonate prior to placing in the drums. The concern with RadPro solutions and cotton rags is that some of the RadPro solutions contain nitric acid. Under the right conditions, nitric acid and cotton rags exothermically react. The concern is, will RadPro solutions react with cotton rags exothermically? The potential for a runaway reaction for any of the RadPro solutions used was studied in Section 5.2 of PNNL-15410, Thermal Stability Studies of Candidate Decontamination Agents for Hanford's Plutonium Finishing Plant Plutonium-Contaminated Gloveboxes. This report shows the thermal behavior of cotton rags having been saturated in one of the various neutralized and non-neutralized RadPro solutions. The thermal analysis was performed using thermogravimetric Analysis (TGA), Differential Thermal Analysis (DTA) and Accelerating Rate Calorimetry (ARC).

CSER 00-001 Criticality Safety Evaluation Report for Cementation Operations at the PFP

Energy Technology Data Exchange (ETDEWEB)

DOBBIN, K.D.

2000-04-18

Glovebox HA-20MB is located in Room 235B of the 234-5Z Building at the Plutonium Finishing Plant. This enclosure contains mixers, mixer bowls, a crusher unit, an isolated inoperable conveyor unit, plutonium residue feed cans, cemented cans, and a feedwater container. Plutonium residue, not conducive to other forms of stabilization, is prepared for storage and ultimate disposal by cementation. The feed residue material cans can have plutonium contents of only a few grams or up to 200 grams. This evaluation accommodates this wide range of container fissile concentrations.

Print Finishing: From Manual to Automated Print Finishing

Directory of Open Access Journals (Sweden)

Gareth Ward

2004-12-01

Full Text Available Meeting the demand for faster turnrounds and shorter print runs goes beyond making the printing press easier to set up and change. There is little point in producing plates and then sheets from a press if the post press area does not change to keep abreast of developments in prepress and the print room. The greatest impact is going to come from JDF, the end to end production data format which is finding wide spread acceptance in print areas. To date finishing equipment manufacturers are not as well represented within the CIP4 organisation as prepress and press vendors, but the major manufacturers are members. All are working to the goal of complete connectivity.The idea of JDF is that if the format of a print product like a magazine is known during the creation phases, the information can be used to preset machinery that is going to be used to produce it, so avoiding input errors and saving manufacturing time.A second aspect to JDF is that information about performance and progress is gathered and can be retrieved from a central point or made available to a customer. Production scheduling and costing becomes more accurate and customer relationships are deepened. However JDF to its fullest extent is not yet in use in connecting the finishing area to the rest of the printing plant. Around the world different companies are testing the idea of JDF to connect saddle stitchers, guillotines and binders with frantic work underway to be able to show results soon.

PFP Commercial Grade Food Pack Cans for Plutonium Handling and Storage Critical Characteristics

International Nuclear Information System (INIS)

BONADIE, E.P.

1999-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for PFP's Vault Operations system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to perform its safety function. The changes in these specifications have no detrimental effect on the descriptions and parameters related to handling plutonium solids in the authorization basis. Because no parameters or sequences exceed the limits described in the authorization bases, no accident or abnormal conditions are affected. The specifications prescribed in this critical characteristics document do not represent an unreviewed safety question

SLIGHTLY IRRADIATED FUEL (SIF) INTERIM DISPOSITION PROJECT

International Nuclear Information System (INIS)

Norton, S.H.

2010-01-01

CH2M HILL Plateau Remediation Company (CH2M HILL PRC) is proud to submit the Slightly Irradiated Fuel (SIF) Interim Disposition Project for consideration by the Project Management Institute as Project of the Year for 2010. The SIF Project was a set of six interrelated sub-projects that delivered unique stand-alone outcomes, which, when integrated, provided a comprehensive and compliant system for storing high risk special nuclear materials. The scope of the six sub-projects included the design, construction, testing, and turnover of the facilities and equipment, which would provide safe, secure, and compliant Special Nuclear Material (SNM) storage capabilities for the SIF material. The project encompassed a broad range of activities, including the following: Five buildings/structures removed, relocated, or built; Two buildings renovated; Structural barriers, fencing, and heavy gates installed; New roadways and parking lots built; Multiple detection and assessment systems installed; New and expanded communication systems developed; Multimedia recording devices added; and A new control room to monitor all materials and systems built. Project challenges were numerous and included the following: An aggressive 17-month schedule to support the high-profile Plutonium Finishing Plant (PFP) decommissioning; Company/contractor changeovers that affected each and every project team member; Project requirements that continually evolved during design and construction due to the performance- and outcome-based nature ofthe security objectives; and Restrictions imposed on all communications due to the sensitive nature of the projects In spite of the significant challenges, the project was delivered on schedule and $2 million under budget, which became a special source of pride that bonded the team. For years, the SIF had been stored at the central Hanford PFP. Because of the weapons-grade piutonium produced and stored there, the PFP had some of the tightest security on the Hanford

SLIGHTLY IRRADIATED FUEL (SIF) INTERIM DISPOSITION PROJECT

Energy Technology Data Exchange (ETDEWEB)

NORTON SH

2010-02-23

CH2M HILL Plateau Remediation Company (CH2M HILL PRC) is proud to submit the Slightly Irradiated Fuel (SIF) Interim Disposition Project for consideration by the Project Management Institute as Project of the Year for 2010. The SIF Project was a set of six interrelated sub-projects that delivered unique stand-alone outcomes, which, when integrated, provided a comprehensive and compliant system for storing high risk special nuclear materials. The scope of the six sub-projects included the design, construction, testing, and turnover of the facilities and equipment, which would provide safe, secure, and compliant Special Nuclear Material (SNM) storage capabilities for the SIF material. The project encompassed a broad range of activities, including the following: Five buildings/structures removed, relocated, or built; Two buildings renovated; Structural barriers, fencing, and heavy gates installed; New roadways and parking lots built; Multiple detection and assessment systems installed; New and expanded communication systems developed; Multimedia recording devices added; and A new control room to monitor all materials and systems built. Project challenges were numerous and included the following: An aggressive 17-month schedule to support the high-profile Plutonium Finishing Plant (PFP) decommissioning; Company/contractor changeovers that affected each and every project team member; Project requirements that continually evolved during design and construction due to the performance- and outcome-based nature ofthe security objectives; and Restrictions imposed on all communications due to the sensitive nature of the projects In spite of the significant challenges, the project was delivered on schedule and $2 million under budget, which became a special source of pride that bonded the team. For years, the SIF had been stored at the central Hanford PFP. Because of the weapons-grade piutonium produced and stored there, the PFP had some of the tightest security on the Hanford

Surface finishing and levelling of thermomechanically hardened rolled steel

International Nuclear Information System (INIS)

Grosval'd, V.G.; Bashchenko, A.P.; Grishkov, A.I.; Gutnik, M.V.; Kanevskij, B.L.; Nikozov, A.I.; Sedov, N.D.; Prosin, K.A.; Safonov, L.I.

1975-01-01

The finishing of high-strength merchant shapes from alloy steel was tried out under industrial conditions with the equipment of metallurgical plants. After thermomechanical hardening in the production line of the rolling mill, 30KhGSN2A and 40Kh1NVA steel rounds 32 and 31 mm in diameter were straightened on a two-roller straightening machine designed by the All-Union Scientific Research Institute for Metallurgical Machinery (VNII Metmash). This made possible subsequent turning and grinding of the rods. The conditions of straightening, turning and grinding have been worked so as to obtain thermomechanically strengthened and ground rolled products approximating the gauged and ground metal in shape geometry and surface finish. It is shown that the labour-consuming operation of turning can be eliminated by reducing the machining pass of the rolled product, and this lowers the labour required for the finishing operations by 75%. After grinding with 40- and 25-grain abrasive wheels, high strength rolled shapes were obtained with a diameter of 30-0.20 mm and a surface finish of class 6-5 satisfying the technical specifications. (author)

MODIFICATION OF RECIPES USED IN THE BLEACHING SECTION OF THE FINISHING PLANT OF THE TEXTILE UNIT "DESEMBARCO DEL GRANMA”

Directory of Open Access Journals (Sweden)

Isabel Cabrera Estada

2017-07-01

Full Text Available The Textile Basic Unit (BU “Desembarco del Granma” of Villa Clara is one of the most important textile industries in Cuba, it is responsible for the provision of a wide variety of fabrics, threads and surgical gauze to various sectors of the country. In the finishing plant of the BU "Desembarco del Granma" a production that meets the parameters set is achieved, but this requires the use of large volumes of costly chemicals and with negative impacts on the environment. To solve this problem an investigation was carried out to evaluate the modification of some of the recipes used in the bleaching section of the finishing plant of the BU "Desembarco del Granma". The results obtained were processed with the Statgraphics software. When the caustic soda is decreased from 60g/L to 40g/L, and it is analyzed the capillarity of warp, it was confirmed that there is no significant difference between the average of the two samples, for a 95,0 % of confidence level; but there were differences between the variances; when analyzing the fabric capillarity it was found that there is no significant difference between the average and the variance of the two samples for a 95,0 % of confidence level. With such modification it is saved 241,4 $/day, by concept of decrease of soda used. The hydrogen peroxide cannot be reduced because it affects the white degree of the fabric.

Definition and means of maintaining the ventilation system confinement portion of the PFP safety envelope

Energy Technology Data Exchange (ETDEWEB)

Dick, J.D.; Grover, G.A.; O`Brien, P.M., Fluor Daniel Hanford

1997-03-05

The Plutonium Finishing Plant Heating Ventilation and Cooling system provides for the confinement of radioactive releases to the environment and provides for the confinement of radioactive contamination within designated zones inside the facility. This document identifies the components and procedures necessary to ensure the HVAC system provides these functions. Appendices E through J provide a snapshot of non-safety class HVAC equipment and need not be updated when the remainder of the document and Appendices A through D are updated.

Integrated Safety Management System Phase I Verification for the Plutonium Finishing Plant (PFP) [VOL 1 & 2

Energy Technology Data Exchange (ETDEWEB)

SETH, S.S.

2000-01-10

U.S. Department of Energy (DOE) Policy 450.4, Safety Management System Policy commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex as a means of accomplishing its missions safely. DOE Acquisition Regulation 970.5204-2 requires that contractors manage and perform work in accordance with a documented safety management system.

Storage for the Fast Flux Test Facility unirradiated fuel in the Plutonium Finishing Plant Complex, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-01-01

This Environmental Assessment evaluates the proposed action to relocate and store unirradiated Fast Flux Test Facility fuel in the Plutonium Finishing Plant Complex on the Hanford Site, Richland, Washington. The US Department of Energy has decided to cease fuel fabrication activities in the 308 Building in the 300 Area. This decision was based on a safety concern over the ability of the fuel fabrication portion of the 308 Building to withstand a seismic event. The proposed action to relocate and store the fuel is based on the savings that could be realized by consolidating security costs associated with storage of the fuel. While the 308 Building belowgrade fuel storage areas are not at jeopardy by a seismic event, the US Department of Energy is proposing to cease storage operations along with the related fabrication operations. The US Department of Energy proposes to remove the unirradiated fuel pins and fuel assemblies from the 308 Building and store them in Room 192A, within the 234-5Z Building, a part of the Plutonium Finishing Plant Complex, located in the 200 West Area. Minor modifications to Room 192A would be required to accommodate placement of the fuel. The US Department of Energy estimates that removing all of the fuel from the 308 Building would save $6.5 million annually in security expenditures for the Fast Flux Test Facility. Environmental impacts of construction, relocation, and operation of the proposed action and alternatives were evaluated. This evaluation concluded that the proposed action would have no significant impacts on the human environment

Comparison of calorimetry and destructive analytical measurement techniques for excess plutonium powders

International Nuclear Information System (INIS)

Welsh, T.L.

1996-01-01

In Dec. 1994, IAEA safeguards were initiated on inventory of Pu- bearing materials, originating from the US nuclear weapons complex, at vault 3 of DOE's Plutonium Finishing Plant at Hanford. Because of the diversity and heterogeneity of the Pu, plant operators have increasingly used calorimetry for accountability measurements. During the recent commencement of IAEA safeguards at vault 3, destructive (electrochemical titration) methods were used to determine Pu concentrations in subsamples of inventory items with widely ranging chemical purities. The Pu concentrations in the subsamples were determined and contribution of heterogeneity to total variability was identified. Measurement results, gathered by PFP and IAEA laboratories, showed total measurement variability for calorimetry to be comparable with or lower than those of sampling and chemical analyses

An atomic-scale and high efficiency finishing method of zirconia ceramics by using magnetorheological finishing

Science.gov (United States)

Luo, Hu; Guo, Meijian; Yin, Shaohui; Chen, Fengjun; Huang, Shuai; Lu, Ange; Guo, Yuanfan

2018-06-01

Zirconia ceramics is a valuable crucial material for fabricating functional components applied in aerospace, biology, precision machinery, military industry and other fields. However, the properties of its high brittleness and high hardness could seriously reduce its finishing efficiency and surface quality by conventional processing technology. In this work, we present a high efficiency and high-quality finishing process by using magnetorheological finishing (MRF), which employs the permanent magnetic yoke with straight air gap as excitation unit. The sub-nanoscale surface roughness and damage free surface can be obtained after magnetorheological finishing. The XRD results and SEM morphologies confirmed that the mechanical shear removal with ductile modes are the dominant material removal mechanism for the magnetorheological finishing of zirconia ceramic. With the developed experimental apparatus, the effects of workpiece speed, trough speed and work gap on material removal rate and surface roughness were systematically investigated. Zirconia ceramics finished to ultra-smooth surface with surface roughness less than Ra 1 nm was repeatedly achieved during the parametric experiments. Additionally, the highest material removal rate exceeded 1 mg/min when using diamond as an abrasive particle. Magnetorheological finishing promises to be an adaptable and efficient method for zirconia ceramics finishing.

Project Execution Plan Project 98L-EWW-460 Plutonium Stabilization and Handling DOE No. 98-D-453

International Nuclear Information System (INIS)

HOLSTEIN, W.A.

1999-01-01

This Project Execution Plan (PEP) describes the management methods and responsibilities of the project participants. Project W-460 is sufficiently large to warrant a stand alone PEP. This project specific PEP describes the relationships and responsibilities of the project team and identifies the technical, schedule, and cost baselines that have been established for the project. The Department of Energy (DOE), Hanford Works (Hanford), at Richland, WA., currently does not have a system capable of stabilizing or packaging large quantities of plutonium-bearing solids to meet DOE technical standard DOE-STD-3013-96. This project will allow Hanford to meet this standard by installing stabilization and packaging equipment (SPE). The SPE is capable of stabilizing and packaging the current inventory of greater than 50 percent plutonium-bearing materials currently stored in the Plutonium Finishing Plant's (PFP) vaults into 3013 storage containers. The scope of this project is to procure and install the SPE via a Hanford contract and coordination with the Savannah River Site. In addition, the project will modify PFP vaults and upgrade the PFP Laboratory measurement systems. The Facility infrastructure will be modified to support the new SPE system and the new standardized storage container configuration. Use of this document is described in the Project Hanford Policy and Procedure System under HNF-PRO-1999, Construction Program Conceptual Phase

Demonstration of acid and water recovery systems: Applicability and operational challenges in Indian metal finishing SMEs.

Science.gov (United States)

Balakrishnan, M; Batra, R; Batra, V S; Chandramouli, G; Choudhury, D; Hälbig, T; Ivashechkin, P; Jain, J; Mandava, K; Mense, N; Nehra, V; Rögener, F; Sartor, M; Singh, V; Srinivasan, M R; Tewari, P K

2018-07-01

Diffusion dialysis, acid retardation and nanofiltration plants were acquired from Europe and demonstrated in several Indian metal finishing companies over a three year period. These companies are primarily small and medium enterprises (SMEs). Free acid recovery rate from spent pickling baths using diffusion dialysis and retardation was in the range of 78-86% and 30-70% respectively. With nanofiltration, 80% recovery rate of rinse water was obtained. The demonstrations created awareness among the metal finishing companies to reuse resources (acid/water) from the effluent streams. However, lack of efficient oil separators, reliable chemical analysis and trained personnel as well as high investment cost limit the application of these technologies. Local manufacturing, plant customization and centralized treatment are likely to encourage the uptake of such technologies in the Indian metal finishing sector. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization of decontamination and decommissioning wastes expected from the major processing facilities in the 200 Areas

International Nuclear Information System (INIS)

Amato, L.C.; Franklin, J.D.; Hyre, R.A.; Lowy, R.M.; Millar, J.S.; Pottmeyer, J.A.; Duncan, D.R.

1994-08-01

This study was intended to characterize and estimate the amounts of equipment and other materials that are candidates for removal and subsequent processing in a solid waste facility when the major processing and handling facilities in the 200 Areas of the Hanford Site are decontaminated and decommissioned. The facilities in this study were selected based on processing history and on the magnitude of the estimated decommissioning cost cited in the Surplus Facilities Program Plan; Fiscal Year 1993 (Winship and Hughes 1992). The facilities chosen for this study include B Plant (221-B), T Plant (221-T), U Plant (221-U), the Uranium Trioxide (UO 3 ) Plant (224-U and 224-UA), the Reduction Oxidation (REDOX) or S Plant (202-S), the Plutonium Concentration Facility for B Plant (224-B), and the Concentration Facility for the Plutonium Finishing Plant (PFP) and REDOX (233-S). This information is required to support planning activities for current and future solid waste treatment, storage, and disposal operations and facilities

Characterization of decontamination and decommissioning wastes expected from the major processing facilities in the 200 Areas

Energy Technology Data Exchange (ETDEWEB)

Amato, L.C.; Franklin, J.D.; Hyre, R.A.; Lowy, R.M.; Millar, J.S.; Pottmeyer, J.A. [Los Alamos Technical Associates, Kennewick, WA (United States); Duncan, D.R. [Westinghouse Hanford Co., Richland, WA (United States)

1994-08-01

This study was intended to characterize and estimate the amounts of equipment and other materials that are candidates for removal and subsequent processing in a solid waste facility when the major processing and handling facilities in the 200 Areas of the Hanford Site are decontaminated and decommissioned. The facilities in this study were selected based on processing history and on the magnitude of the estimated decommissioning cost cited in the Surplus Facilities Program Plan; Fiscal Year 1993 (Winship and Hughes 1992). The facilities chosen for this study include B Plant (221-B), T Plant (221-T), U Plant (221-U), the Uranium Trioxide (UO{sub 3}) Plant (224-U and 224-UA), the Reduction Oxidation (REDOX) or S Plant (202-S), the Plutonium Concentration Facility for B Plant (224-B), and the Concentration Facility for the Plutonium Finishing Plant (PFP) and REDOX (233-S). This information is required to support planning activities for current and future solid waste treatment, storage, and disposal operations and facilities.

Wire Finishing Mill Rolling Bearing Fault Diagnosis Based on Feature Extraction and BP Neural Network

Directory of Open Access Journals (Sweden)

Hong-Yu LIU

2014-10-01

Full Text Available Rolling bearing is main part of rotary machine. It is frail section of rotary machine. Its running status affects entire mechanical equipment system performance directly. Vibration acceleration signals of the third finishing mill of Anshan Steel and Iron Group wire plant were collected in this paper. Fourier analysis, power spectrum analysis and wavelet transform were made on collected signals. Frequency domain feature extraction and wavelet transform feature extraction were made on collected signals. BP neural network fault diagnosis model was adopted. Frequency domain feature values and wavelet transform feature values were treated as neural network input values. Various typical fault models were treated as neural network output values. Corresponding relations between feature vector and fault omen were utilized. BP neural network model of typical wire plant finishing mill rolling bearing fault was constructed by training many groups sample data. After inputting sample needed to be diagnosed, wire plant finishing mill rolling bearing fault can be diagnosed. This research has important practical significance on enhancing rolling bearing fault diagnosis precision, repairing rolling bearing duly, decreasing stop time, enhancing equipment running efficiency and enhancing economic benefits.

Windows Calorimeter Control (WinCal) system configuration control board (SCCB) operating procedure

International Nuclear Information System (INIS)

Westsik, G.A.

1997-01-01

This document describes the operating procedure for the System Configuration Control Board (SCCB) performed in support of the Windows Calorimeter Control (WinCal) system. This board will consist of representatives from Babcock and Wilcox Hanford Company Babcock and Wilcox Protec, Inc.; and Lockheed Martin Services, Inc. In accordance with agreements for the joint use of the Babcock and Wilcox Hanford Company calorimeters located in the Hanford Site Plutonium Finishing Plant (PFP) Nondestructive Assay Laboratory, concurrence regarding changes to the WinCal system will be obtained from the International Atomic Energy Agency (IAEA). Further, changes to the WinCal software will be communicated to Los Alamos National Laboratory

Conceptual design report, plutonium stabilization and handling,project W-460

Energy Technology Data Exchange (ETDEWEB)

Weiss, E.V.

1997-03-06

Project W-460, Plutonium Stabilization and Handling, encompasses procurement and installation of a Stabilization and Packaging System (SPS) to oxidize and package for long term storage remaining plutonium-bearing special nuclear materials currently in inventory at the Plutonium Finishing Plant (PFP), and modification of vault equipment to allow storage of resulting packages of stabilized SNM for up to fifty years. This Conceptual Design Report (CDR) provides conceptual design details for the vault modification, site preparation and site interface with the purchased SPS. Two concepts are described for vault configuration; acceleration of this phase of the project did not allow completion of analysis which would clearly identify a preferred approach.

Finishing of wood

Science.gov (United States)

R. Sam Williams

1999-01-01

The primary function of any wood finish (paint, varnish, and stain, for example) is to protect the wood surface, help maintain a certain appearance, and provide a cleanable surface. Although wood can be used both outdoors and indoors without finishing, unfinished wood surfaces exposed to the weather change color, are roughened by photodegradation and surface checking,...

Definition and means of maintaining the supply ventilation system seismic shutdown portion of the PFP safety envelope. Revision 2

International Nuclear Information System (INIS)

Keck, R.D.

1995-01-01

This report describes the modifications to the ventilation system for the Plutonium Finishing Plant. Topics discussed in this report include; system functional requirements, evaluations of equipment, a list of drawings showing the safety envelope boundaries; list of safety envelope equipment, functional requirements for individual safety envelope equipment, and a list of the operational, maintenance and surveillance procedures necessary to operate and maintain the system equipment

Female PFP patients present alterations in eccentric muscle activity but not the temporal order of activation of the vastus lateralis muscle during the single leg triple hop test.

Science.gov (United States)

Kalytczak, Marcelo Martins; Lucareli, Paulo Roberto Garcia; Dos Reis, Amir Curcio; Bley, André Serra; Biasotto-Gonzalez, Daniela Aparecida; Correa, João Carlos Ferrari; Politti, Fabiano

2018-04-07

This study aimed to compare the concentric and eccentric activity and the temporal order of peak activity of the hip and knee muscles between women with patellofemoral pain (PFP) and healthy women during the single leg triple hop test (SLTHT). Electromyographic (EMG) and Kinematic data were collected from 14 healthy women (CG) and 14 women diagnosed with PFP (PFG) during a single session of the single leg triple hop test. Integral surface electromyography (iEMG) data of the hip and knee muscles in eccentric and concentric phases and the length of time that each muscle needed to reach the maximal peak of muscle activity were calculated. The iEMG in the eccentric phase was significantly higher (p < 0.05) than the concentric phase, for the gluteus maximus and gluteus medius muscles (CG and PFG) and for the vastus lateralis muscle (PFG). The vastus lateralis muscle was the first muscle to reach the highest peak of activity in the PFG, and the third to reach this peak in the CG. In the present study, the activity of the vastus lateralis muscle during the eccentric phase of the jump was greater than concentric phase, as a temporal anticipation of its peak in activity among women with PFP. Copyright © 2018 Elsevier B.V. All rights reserved.

Establishing Trailer Ventilation (Boarding) Requirements for Finishing Pigs during Transport.

Science.gov (United States)

McGlone, John; Sapkota, Avi; Johnson, Anna; Kephart, Rebecca

2014-08-19

Specifically, this study aimed to establish the effects on mortality and morbidity of boarding levels (amount of side-wall trailer ventilation) for finishing pigs in mild weather (8.80 ± 0.30 °C, 71.70% ± 1.12% humidity). Pigs from commercial finishing sites were transported in 302 pot-bellied trailers to commercial processing plants. Measures collected at the processing plant were rates of dead on arrival (DOA), non-ambulatory, non-injured (NANI), non-ambulatory, injured (NAI), and total dead and down (D&D). Boarding levels (% that side walls were closed off with inserted boards) were divided into 3 bins: low, medium, and high, and outside temperature was divided into 4 bins 15 °C. Average rates of DOA, NANI, NAI, and D&D were approximately 0.30%, 0.12%, 0.04%, and 0.46%, respectively. The D&D was highest when boarding level was low with temperatures boarding level (medium and high boarding) in the temperature range of 5.10 °C to 23.30 °C did not affect pig losses.

Integrated Safety Management System Phase I Verification for the Plutonium Finishing Plant (PFP) [VOL 1 and 2

International Nuclear Information System (INIS)

SETH, S.S.

2000-01-01

U.S. Department of Energy (DOE) Policy 450.4, Safety Management System Policy commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex as a means of accomplishing its missions safely. DOE Acquisition Regulation 970.5204-2 requires that contractors manage and perform work in accordance with a documented safety management system

Economics of finishing Tanzania Shorthorn Zebu cattle in feedlot and optimum finishing period

DEFF Research Database (Denmark)

Asimwe, L.; Kimambo, A E; Laswai, G. H.

2016-01-01

finishing for TSZ cattle. The biological data collected from the two experiments were used as basis for deriving the economic scenarios. The range of days steers were kept in feedlot was set at 0, 25, 50, 75 and 100 days. The dietary metabolisable energy intake (MEI) levels used in the study were 55 MJ......Economic potential of finishing Tanzania Shorthorn Zebu (TSZ) cattle in feedlot was analysed using data obtained from two feedlot experiments carried out at Kongwa ranch in Tanzania. The experiments were performed to evaluate the effects of feeding agro-processing by products and length of feedlot...... length of 25 days, higher profit per animal carcass was realized with long stays (100 days, 238,000 TSh.) than short stays (25 days, 37,600 TSh.). It was concluded that the high feeding level is the most profitable irrespective of meat price and finishing length. The optimum finishing length is between...

Compilation of PRF Canyon Floor Pan Sample Analysis Results

Energy Technology Data Exchange (ETDEWEB)

Pool, Karl N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Minette, Michael J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wahl, Jon H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Greenwood, Lawrence R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coffey, Deborah S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McNamara, Bruce K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bryan, Samuel A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Scheele, Randall D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Delegard, Calvin H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sinkov, Sergey I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Soderquist, Chuck Z. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fiskum, Sandra K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Brown, Garrett N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Clark, Richard A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-06-30

common anions, gamma spectrometry, metals, corrosivity, organics and alpha spectrometry (note: alpha spectrometry was cancelled during the performance of this work with concurrence from CHPRC). Results may help elucidate the components that led to the unexpected reaction in the canyon as well as inform the radiological and hazardous characteristics. The specific anions, gamma emitters, organics and metals requested by CHPRC are provided in the analytical reports sections. The individual analyses were conducted under the Plutonium Finishing Plant (PFP) Floor Pan Evaluation Project Quality Assurance Project Plan (PFP Floor Pan Evaluation QAPP, Revision 0.) developed by PNNL specifically for this project. The final reports for each analysis set are included in this compilation of the results. Each package was reviewed under the PFP Floor Pan Evaluation Project Quality Assurance Project Plan so no additional reviews were conducted in this compilation task. The Gas Generation Rates in Appendix G were conducted under the PNNL “How Do I…” quality assurance program and were NOT conducted under the Plutonium Finishing Plant (PFP) Floor Pan Evaluation Project Quality Assurance Project Plan (PFP Floor Pan Evaluation QAPP, Revision 0.).

Transition projects, Fiscal Year 1996: Multi-Year Program Plan (MYPP) for WBS 1.31, 7.1, and 6.13. Revision 1, Volume 1

Energy Technology Data Exchange (ETDEWEB)

Cartmell, D.B.

1995-09-01

Based on US Department of Energy (DOE), Richland Operations Office (RL) review, specific areas of Westinghouse Hanford Company (WHC), Transition Projects ``Draft`` Multi-Year Program Plan (MYPP) were revised in preparation for the RL approval ceremony on September 26, 1995. These changes were reviewed with the appropriate RL Project Manager. The changes have been incorporated to the MYPP electronic file, and hard copies replacing the ``Draft`` MYPP will be distributed after the formal signing. In addition to the comments received, a summary level schedule and outyear estimates for the K Basin deactivation beginning in FY 2001 have been included. The K Basin outyear waste data is nearing completion this week and will be incorporated. This exclusion was discussed with Mr. N.D. Moorer, RL, Facility Transition Program Support/Integration. The attached MYPP scope/schedule reflects the Integrated Target Case submitted in the April 1995 Activity Data Sheets (ADS) with the exception of B Plant and the Plutonium Finishing Plant (PFP). The 8 Plant assumption in FY 1997 reflects the planning case in the FY 1997 ADS with a shortfall of $5 million. PFP assumptions have been revised from the FY 1997 ADS based on the direction provided this past summer by DOE-Headquarters. This includes the acceleration of the polycube stabilization back to its originally planned completion date. Although the overall program repricing in FY 1996 allowed the scheduled acceleration to fall with the funding allocation, the FY 1997 total reflects a shortfall of $6 million.

Transition projects, Fiscal Year 1996: Multi-Year Program Plan (MYPP) for WBS 1.31, 7.1, and 6.13. Revision 1, Volume 1

International Nuclear Information System (INIS)

Cartmell, D.B.

1995-09-01

Based on US Department of Energy (DOE), Richland Operations Office (RL) review, specific areas of Westinghouse Hanford Company (WHC), Transition Projects ''Draft'' Multi-Year Program Plan (MYPP) were revised in preparation for the RL approval ceremony on September 26, 1995. These changes were reviewed with the appropriate RL Project Manager. The changes have been incorporated to the MYPP electronic file, and hard copies replacing the ''Draft'' MYPP will be distributed after the formal signing. In addition to the comments received, a summary level schedule and outyear estimates for the K Basin deactivation beginning in FY 2001 have been included. The K Basin outyear waste data is nearing completion this week and will be incorporated. This exclusion was discussed with Mr. N.D. Moorer, RL, Facility Transition Program Support/Integration. The attached MYPP scope/schedule reflects the Integrated Target Case submitted in the April 1995 Activity Data Sheets (ADS) with the exception of B Plant and the Plutonium Finishing Plant (PFP). The 8 Plant assumption in FY 1997 reflects the planning case in the FY 1997 ADS with a shortfall of $5 million. PFP assumptions have been revised from the FY 1997 ADS based on the direction provided this past summer by DOE-Headquarters. This includes the acceleration of the polycube stabilization back to its originally planned completion date. Although the overall program repricing in FY 1996 allowed the scheduled acceleration to fall with the funding allocation, the FY 1997 total reflects a shortfall of $6 million

Addendum 3 to CSAR 80-027, Use of calorimeter 109B for fissile material measurement

International Nuclear Information System (INIS)

Chiao, T.

1994-01-01

This modification to the Plutonium Finishing Plant (PFP) calorimeter system involves removing current calorimeter No. 3 from the water bath and replacing it with a calorimeter that can accommodate larger diameter items (an oversize can). The inside diameters of both the sample and the reference cells will be increased to 5.835 inches at the top opening and to 5.22 inches at the bottom, the 8 inch high measurement zone. This Addendum 3 to Criticality Safety Analysis Report 80-027 examines criticality safety during the use of the modified calorimeter (Calorimeter 109B) with enlarged cell tube diameters to assure that an adequate margin of subcriticality is maintained for all normal and contingency conditions

27 CFR 25.231 - Finished beer.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Finished beer. 25.231... OF THE TREASURY LIQUORS BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

Supplementation with plant extracts (carvacrol, cinnamaldehyde and capsaicin): its effects on acid-base status and productive performance in growing/finishing bull calves.

Science.gov (United States)

Hernández, Joaquín; Benedito, José Luís; Vázquez, Patricia; Pereira, Victor; Méndez, Jesús; Sotillo, Juan; Castillo, Cristina

2009-01-01

This study investigated the in vivo effects of a commercial blend of plant extracts (carvacrol, cinnamaldehyde and capsaicin) on blood acid-base balance and serum lactate levels in a 148-day feedlot experimentwith 24 double-muscled Belgian Blue bull calves. Animals were allotted randomly to one of two experimental groups: 1) a control group (C, no supplementation; n = 10), and 2) a group receiving dietary supplementation with a combination of plant extracts (PE, 100 mg per kg DM of concentrate; n = 14). All animals received a high-grain ration, typical of diets fed commercially to feedlot cattle in Spain, consisting mainly of barley plus other components in proportions depending on the production phase. Production data (weight, DMI, ADG and feed-to-gain ratio) were recorded, and venous blood pH, pCO2, HCO3(-), Base Excess -BE- and serum L-lactate were determined. Apparently, beneficial effects of supplementation on production parameters were observed in both growing and finishing periods, though statistically significant effects were only observed in the finishing period. As regards blood parameters, no significant effects of supplementation (or the supplementation x time interaction) were observed, except for an effect on blood pH in the growing period, when supplemented animals showed significantly higher values than controls. A beneficial supplementation x time interactive effect was observed on serum L-lactate levels: from the first week of the study until the end, supplemented animals showed significantly lower levels than controls. These in vivo results support the utility of this dietary supplement in feedlot cattle receiving a barley-based high-grain diet.

Safety analysis report for packaging (onsite) transuranic performance demonstration program sample packaging

International Nuclear Information System (INIS)

Mccoy, J.C.

1997-01-01

The Transuranic Performance Demonstration Program (TPDP) sample packaging is used to transport highway route controlled quantities of weapons grade (WG) plutonium samples from the Plutonium Finishing Plant (PFP) to the Waste Receiving and Processing (WRAP) facility and back. The purpose of these shipments is to test the nondestructive assay equipment in the WRAP facility as part of the Nondestructive Waste Assay PDP. The PDP is part of the U. S. Department of Energy (DOE) National TRU Program managed by the U. S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico. Details of this program are found in CAO-94-1045, Performance Demonstration Program Plan for Nondestructive Assay for the TRU Waste Characterization Program (CAO 1994); INEL-96/0129, Design of Benign Matrix Drums for the Non-Destructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996a); and INEL-96/0245, Design of Phase 1 Radioactive Working Reference Materials for the Nondestructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996b). Other program documentation is maintained by the national TRU program and each DOE site participating in the program. This safety analysis report for packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the TRU PDP sample packaging meets the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for an onsite Transportation Hazard Indicator (THI) 2 packaging. This SARP, however, does not include evaluation of any operations within the PFP or WRAP facilities, including handling, maintenance, storage, or operating requirements, except as they apply directly to transportation between the gate of PFP and the gate of the WRAP facility. All other activities are subject to the requirements of the facility safety analysis reports (FSAR) of the PFP or WRAP facility and requirements of the PDP

Remote-Reading Safety and Safeguards Surveillance System for 3013 Containers

International Nuclear Information System (INIS)

Lechelt, W. M.; Skorpik, J. R.; Silvers, K. L.; Szempruch, R. W.; Douglas, D. G.; Fein, K. O.

2002-01-01

At Hanford's Plutonium Finishing Plant (PFP), plutonium oxide is being loaded into stainless steel containers for long-term storage on the Hanford Site. These containers consist of two weld-sealed stainless steel cylinders nested one within the other. A third container holds the plutonium within the inner cylinder. This design meets the U.S. Department of Energy (DOE) storage standard, DOE-STD- 3013-2000, which anticipates a 50-year storage lifetime. The 3013 standard also requires a container surveillance program to continuously monitor pressure and to assure safeguards are adequate. However, the configuration of the container system makes using conventional measurement and monitoring methods difficult. To better meet the 3013 monitoring requirements, a team from Fluor Hanford (who manages the PFP), Pacific Northwest National Laboratory (PNNL), and Vista Engineering Technologies, LLC, developed a safer, cost-efficient, remote PFP 3013 container surveillance system. This new surveillance system is a combination of two successfully deployed technologies: (1) a magnetically coupled pressure gauge developed by Vista Engineering and (2) a radio frequency (RF) tagging device developed by PNNL. This system provides continuous, 100% monitoring of critical parameters with the containers in place, as well as inventory controls. The 3013 container surveillance system consists of three main elements: (1) an internal magnetic pressure sensor package, (2) an instrument pod (external electronics package), and (3) a data acquisition storage and display computer. The surveillance system described in this paper has many benefits for PFP and DOE in terms of cost savings and reduced personnel exposure. In addition, continuous safety monitoring (i.e., internal container pressure and temperature) of every container is responsible nuclear material stewardship and fully meets and exceeds DOE's Integrated Surveillance Program requirements

CSER 94-014: Storage of metal-fuel loaded EBR-II casks in concrete vault on PFP grounds

International Nuclear Information System (INIS)

Hess, A.L.

1994-01-01

A criticality safety evaluation is presented to permit EBR-2 spent fuel casks loaded with metallic fuel rods to be stored in an 8-ft diameter, cylindrical concrete vault inside the PFP security perimeter. The specific transfer of three casks with Pu alloy fuel from the Los Alamos Molten Plutonium Reactor Experiment from the burial grounds to the vault is thus covered. Up to seven casks may be emplaced in the casing with 30 inches center to center spacing. Criticality safety is assured by definitive packaging rules which keep the fissile medium dry and at a low effective volumetric density

Population dynamics of swine influenza virus in farrow-to-finish and specialised finishing herds in the Netherlands

NARCIS (Netherlands)

Loeffen, W.L.A.; Hunneman, W.A.; Quak, J.; Verheijden, J.H.M.; Stegeman, J.A.

2009-01-01

Influenza virus infections with subtypes H1N1, H3N2 and H1N2 are very common in domestic pigs in Europe. Data on possible differences of population dynamics in finishing pigs in farrow-to-finish herds and in specialised finishing herds are, however, scarce. The presence of sows and weaned piglets on

Automation in tube finishing bay

International Nuclear Information System (INIS)

Bhatnagar, Prateek; Satyadev, B.; Raghuraman, S.; Syama Sundara Rao, B.

1997-01-01

Automation concept in tube finishing bay, introduced after the final pass annealing of PHWR tubes resulted in integration of number of sub-systems in synchronisation with each other to produce final cut fuel tubes of specified length, tube finish etc. The tube finishing bay which was physically segregated into four distinct areas: 1. tube spreader and stacking area, 2. I.D. sand blasting area, 3. end conditioning, wad blowing, end capping and O.D. wet grinding area, 4. tube inspection, tube cutting and stacking area has been studied

7 CFR 29.2518 - Finish.

Science.gov (United States)

2010-01-01

...-Cured Tobacco (u.s. Types 22, 23, and Foreign Type 96) § 29.2518 Finish. The reflectance factor in color perception. Finish indicates the sheen or shine of the surface of a tobacco leaf. (See chart, § 29.2601.) ...

Literature review supporting assessment of potential radionuclides in the 291-Z exhaust ventilation

International Nuclear Information System (INIS)

Mahoney, L.A.; Ballinger, M.Y.; Jette, S.J.; Thomas, L.M. Glissmeyer, J.A.; Davis, W.E.

1994-08-01

This literature review was prepared to support a study conducted by Pacific Northwest Laboratory to assess the potential deposition and resuspension of radionuclides in the 291-Z ventilation exhaust building located in the 200 West Area of the US Department of Energy's Hanford Project near Richland, Washington. The filtered ventilation air from three of the facilities at the Plutonium Finishing Plant (PFP) complex are combined together in the 291-Z building before discharge through a common stack. These three facilities contributing filtered exhaust air to the discharge stream are (1) the PFP, also known as the Z-Plant or 234-5Z, (2) the Plutonium Reclamation Facility (PRF or 236-Z), and (3), the Waste Incinerator Building (WIB or 232-Z). The 291-Z building houses the exhaust fans that pull air from the 291-Z central collection plenum and exhausts the air to the stack. Section 2.0 of this report is a description of the physical characteristic of the ventilation system from the High Efficiency Particulate Air (HEPA) filters to the exhaust stack. A description of the processes performed in the facilities that are vented through 291-Z is given in Section 3.0. The description focuses on the chemical and physical forms of potential aerosols given off from the unit operations. A timeline of the operations and events that may have affected the deposition of material in the ventilation system is shown. Aerosol and radiation measurements taken in previous studies are also discussed. Section 4.0 discusses the factors that influence particle deposition and adhesion. Mechanisms of attachment and resuspension are covered with specific attention to the PFP ducts. Conclusions and recommendations are given in Section 5.0

Finishing with invisalign.

Science.gov (United States)

Duong, Trang; Kuo, Eric

2006-01-01

Finishing in orthodontics can be challenging and can involve use of various techniques and armamentarium. This article reports a study that evaluates a procedure for using a thicker Aligner at the end of treatment to aide in finishing and also to determine if this would reduce the need for additional "case refinement" Aligners at the end of treatment. Align Technology has developed the Invisalign System, which is a series of clear plastic appliances ("aligners") that move the patient's teeth in small increments from their original state to a final, treated state. The Invisalign System uses a computer as a tool to assist in creating a series of sequential movements to assure light and consistent forces on the patient's teeth.

Best of both worlds : clear exterior finishes : in search of finishes that protect wood without hiding its natural beauty

Science.gov (United States)

Tom Daniels; Marc Hirsch; Ken McClelland; Alan Ross; Sam Williams

2000-01-01

In recent years, a number of clear wood finishes have been developed that protect wood while accentuating its natural beauty. The focus of this publication is on those finishes having little visible pigment. In some cases, the pigments are included but are finely ground to create a coating that is transparent to visible light. Most natural clear wood finishes are...

Finishing procedures action on mechanical characteristics of pressed ceramics

Directory of Open Access Journals (Sweden)

Mohamed Abdel Moniem Ahmed

2018-06-01

Conclusions& significance: Grinding & finishing procedures of pressed ceramics showed significant effect Of drill speed and polishing technique over flexural strength, As Grinding with no finishing and polishing procedure showed lowest flexural Strength values followed by finishing and polishing procedure followed by finishing and polishing with polishing paste procedure.

Occurrence of neonicotinoid insecticides in finished drinking water and fate during drinking water treatment

Science.gov (United States)

Klarich, Kathryn L.; Pflug, Nicholas C.; DeWald, Eden M.; Hladik, Michelle L.; Kolpin, Dana W.; Cwiertny, David M.; LeFevre, Gergory H.

2017-01-01

Neonicotinoid insecticides are widespread in surface waters across the agriculturally-intensive Midwestern US. We report for the first time the presence of three neonicotinoids in finished drinking water and demonstrate their general persistence during conventional water treatment. Periodic tap water grab samples were collected at the University of Iowa over seven weeks in 2016 (May-July) after maize/soy planting. Clothianidin, imidacloprid, and thiamethoxam were ubiquitously detected in finished water samples and ranged from 0.24-57.3 ng/L. Samples collected along the University of Iowa treatment train indicate no apparent removal of clothianidin and imidacloprid, with modest thiamethoxam removal (~50%). In contrast, the concentrations of all neonicotinoids were substantially lower in the Iowa City treatment facility finished water using granular activated carbon (GAC) filtration. Batch experiments investigated potential losses. Thiamethoxam losses are due to base-catalyzed hydrolysis at high pH conditions during lime softening. GAC rapidly and nearly completely removed all three neonicotinoids. Clothianidin is susceptible to reaction with free chlorine and may undergo at least partial transformation during chlorination. Our work provides new insights into the persistence of neonicotinoids and their potential for transformation during water treatment and distribution, while also identifying GAC as an effective management tool to lower neonicotinoid concentrations in finished drinking water.

Project Management Plan for Material Stabilization

International Nuclear Information System (INIS)

SPEER, D.R.

1999-01-01

This plan presents the overall objectives, description, justification and planning for the plutonium Finishing Plant (PFP) Materials Stabilization project. The intent of this plan is to describe how this project will be managed and integrated with other facility stabilization and deactivation activities. This plan supplements the overall integrated plan presented in the Plutonium Finishing Plant Integrated Project Management Plan (IPMP), HNF-3617/Rev. 0. This is the top-level definitive project management document that specifies the technical (work scope), schedule, and cost baselines to manager the execution of this project. It describes the organizational approach and roles/responsibilities to be implemented to execute the project. This plan is under configuration management and any deviations must be authorized by appropriate change control action. Materials stabilization is designated the responsibility to open and stabilize containers of plutonium metal, oxides, alloys, compounds, and sources. Each of these items is at least 30 weight percent plutonium/uranium. The output of this project will be containers of materials in a safe and stable form suitable for storage pending final packaging and/or transportation offsite. The corrosion products along with oxides and compounds will be stabilized via muffle furnaces to reduce the materials to high fired oxides

Salmonella enterica prevalence in finishing pigs at slaughter plants in Northern Italy

Directory of Open Access Journals (Sweden)

Irene Alpigiani

2014-04-01

Full Text Available Finishing pigs carrying Salmonella enterica are believed to be the main source of carcass contamination at the beginning of slaughtering. The aim of this study was to assess the S. enterica carrier status of finishing pigs at herd level by sampling pooled faeces on farm and mesenteric lymph nodes at slaughter in the North East of Italy. Environmental faecal samples belonging to 30 batches of pigs were collected on farm. At slaughter, mesenteric lymph nodes were collected from five randomly selected pigs per batch. S. enterica was isolated from 16 lymph nodes out of 150 (10.6% and from seven out of 30 (23.3% faecal samples. Four batches (13.3% were positive to S. enterica both in lymph nodes and in faeces. The number of batches positive to S. enterica either in lymph nodes or in faeces was 13 out of 30 (43.3%. The most prevalent serovars from lymph nodes were S. Derby (25.0% and S. Typhimurium monophasic variant 1, 4,[5],12:i:- (18.6%, which were also isolated from faecal material (14.3 and 42.8% respectively. Contaminated faecal material or lymph nodes could be a primary source of carcass contamination at slaughter during evisceration. S. enterica contamination is widespread on pig farms and carrier pigs pass undetected the inspection visits at slaughter, entering the food chain. Therefore, in order to control S. enterica in pigs, the need to quantify possible risk factors at slaughter and develop effective management strategies on farm is of paramount importance to ensure food safety.

Finishability of CCA pressure-treated wood

Science.gov (United States)

Alan Ross; Richard Carlson; William Feist; Steven Bussjaeger

2000-01-01

Thus, a need arose for the development of surface finishes for CCA-treated wood that could address the special requirements of this substrate and provide protection against the ravages of water, sunlight, mildew, and other aspects of weathering and wear. Initially, this need was not addressed, most wood preserving companies had little expertise in surface finishes and...

Ash Stabilization Campaign Blend Plan

International Nuclear Information System (INIS)

Winstead, M.L.

1995-01-01

This Stabilization Blend Plan documents the material to be processed and the processing order for the FY95 Ash Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing ash. The source of the ash is from Rocky Flats and the 232-Z incinerator at the Plutonium Finishing Plant (PFP). The ash is currently being stored in Room 235B and Vault 174 in building 234-5Z. The sludge is to be thermally stabilized in a glovebox in room 230A of the 234-5Z building and material handling for the process will be done in room 230B of the same building. The campaign is scheduled for approximately 12--16 weeks. A total of roughly 4 kg of Pu will be processed

Hanford Site Near-Facility Environmental Monitoring Data Report for Calendar Year 2007- Appendix 2

Energy Technology Data Exchange (ETDEWEB)

Perkins, Craig J.; Dorsey, Michael; Mckinney, Stephen M.; Wilde, Justin W.; Duncan, Joanne P.

2008-10-13

Near-facility environmental monitoring is defined as monitoring near facilities that have the potential to discharge or have discharged, stored, or disposed of radioactive or hazardous materials. Monitoring locations are associated with nuclear facilities such as the Plutonium Finishing Plant (PFP), Canister Storage Building (CSB), and the K Basins; inactive nuclear facilities such as N Reactor and the Plutonium-Uranium Extraction (PUREX) Facility; and waste storage or disposal facilities such as burial grounds, cribs, ditches, ponds, tank farms, and trenches. Much of the monitoring consists of collecting and analyzing environmental samples and methodically surveying areas near facilities. The program is also designed to evaluate acquired analytical data, determine the effectiveness of facility effluent monitoring and controls, assess the adequacy of containment at waste disposal units, and detect and monitor unusual conditions.

Glazed Tiles as Floor Finish in Nigeria

Directory of Open Access Journals (Sweden)

Toyin Emmanuel AKINDE

2013-09-01

Full Text Available Tile is no doubt rich in antiquity; its primordial  show, came as mosaic with primary prospect in sacred floor finish before its oblivion, courtesy of, later consciousness towards wall finish in banquets, kitchens, toilets, restaurants and even bars. Today, its renaissance as floor finish is apparent in private and public architectural structures with prevalence in residential, recreational, commercial, governmental and other spaces. In Nigeria, the use of glazed tiles as floor finish became apparent, supposedly in mid-twentieth century; and has since, witnessed ever increasing demands from all sundry; a development that is nascent and has necessitated its mass  production locally with pockets of firms in the country. The latter however, is a resultant response to taste cum glazed tiles affordability, whose divergent sophistication in design, colour, size and shape is believed preferred to terrazzo, carpet and floor flex tile. Accessible as glazed tile and production is, in recent times; its dearth of a holistic literature in Nigeria is obvious. In the light of the latter, this paper examine glazed tiles as floor finish in Nigeria, its advent, usage, production, challenge, benefit and prospect with the hope of opening further frontier in discipline specifics.

Radioactive Air Emission Notice of Construction for (NOC) Plutonium Finishing Plant (PFP) Project W-460 Plutonium Stabilization and Handling

International Nuclear Information System (INIS)

JANSKY, M.T.

2000-01-01

The following description and any attachments and references are provided to the Washington State Department of Health (WDOH), Division of Radiation Protection, Air Emissions and Defense Waste Section as a notice of construction (NOC) in accordance with Washington Administrative Code (WAC) 246-247, Radiation Protection-Air Emissions. The WAC 246-247-060, ''Applications, registration, and licensing'', states ''This section describes the information requirements for approval to construct, modify, and operate an emission unit. Any NOC requires the submittal of information listed in Appendix A,'' Appendix A (WAC 246-247-1 IO) lists the requirements that must be addressed. Additionally, the following description, attachments, and references are provided to the U.S. Environmental Protection Agency (EPA) as an NOC, in accordance with Title 40 Code of Federal Regulations (CFR), Part 61, ''National Emission Standards for Hazardous Air Pollutants.'' The information required for submittal to the EPA is specified in 40 CFR 61.07. The potential emissions from this activity are estimated to provide greater than 0.1 millirem year total effective dose equivalent (TEDE) to the hypothetical offsite maximally exposed individual (MEI) and commencement is needed within a short time. Therefore, this application also is intended to provide notification of the anticipated date of initial startup in accordance with the requirement listed in 40 CFR 61.09(a)(1), and it is requested that approval of this application also constitutes EPA acceptance of this initial startup notification. Written notification of the actual date of initial startup, in accordance with the requirement listed in 40 CFR 61.09(a)(2), will be provided later. This NOC covers the activities associated with the construction and operation activities involving stabilization and/or repackaging of plutonium in the 2736-ZB Building. An operations support trailer will be installed in the proximity of the 2736-ZB Building. A new exhaust stack will be built and operated at the 2736-ZB Building to handle the effluents associated with the operation of the stabilization and repackaging process. Figures provided are based on preliminary design

Definition and means of maintaining the room continuous air monitors portion of the plutonium finishing plant (PFP) safety envelope

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

Room Continuous Air Monitors (CAMs) are used in areas where there is potential for dispersible radioactive material. These CAMs provide audible and visual alarms to warn personnel of an increase in airborne radioactivity

CAPSULE REPORT - MANAGING CYANIDE IN METAL FINISHING

Science.gov (United States)

The purpose of this document is to provide guidance to surface finishing manufacturers, metal finishing decision maker and regulators on management practices and control technologies for managing cyanide in the workplace. This information can benefit key industry stakeholder gro...

Legume finishing provides beef with positive human dietary fatty acid ratios and consumer preference comparable with grain-finished beef.

Science.gov (United States)

Chail, A; Legako, J F; Pitcher, L R; Griggs, T C; Ward, R E; Martini, S; MacAdam, J W

2016-05-01

Consumer liking, proximate composition, pH, Warner-Bratzler shear force, fatty acid composition, and volatile compounds were determined from the LM (longissimus thoracis) of cattle ( = 6 per diet) finished on conventional feedlot (USUGrain), legume, and grass forage diets. Forage diets included a condensed tannin-containing perennial legume, birdsfoot trefoil (; USUBFT), and a grass, meadow brome ( Rehmann; USUGrass). Moreover, representative retail forage (USDA Certified Organic Grass-fed [OrgGrass]) and conventional beef (USDA Choice, Grain-fed; ChGrain) were investigated ( = 6 per retail type). The ChGrain had the greatest ( 0.05) to that of both USUGrain and USUGrass. Both grain-finished beef treatments were rated greater ( Consumer liking of USUBFT beef tenderness, fattiness, and overall liking were comparable ( > 0.05) with that of USUGrain and ChGrain. Flavor liking was rated greatest ( 0.05) to those of ChGrain, USUGrass, and OrgGrass. Cumulative SFA and MUFA concentrations were greatest ( 0.05) to those of USUGrain and USUGrass. Each forage-finished beef treatment, USUGrass, OrgGrass, and USUBFT, had lower ( < 0.001) ratios of -6:-3 fatty acids. Hexanal was the most numerically abundant volatile compound. The concentration of hexanal increased with increasing concentrations of total PUFA. Among all the lipid degradation products (aldehydes, alcohols, furans, carboxylic acids, and ketones) measured in this study, there was an overall trend toward greater quantities in grain-finished products, lower quantities in USUGrass and OrgGrass, and intermediate quantities in USUBFT. This trend was in agreement with IMF content, fatty acid concentrations, and sensory attributes. These results suggest an opportunity for a birdsfoot trefoil finishing program, which results in beef comparable in sensory quality with grain-finished beef but with reduced -6 and SFA, similar to grass-finished beef.

Corrosion protection and finishing of automobiles

International Nuclear Information System (INIS)

Sheikh, S.T.

2005-01-01

finishing of automobiles is an important aspect. There have been considerable reductions of weight in automobiles by the use of composites components replacing heavy metallic components. Fenders previously based on metal have been replaced with plastic and painted with the same colour shade as of the metallic body, this has eps for proper adhesion of the paints on the plastic fender to avoid chipping off the paint form it. This paper discusses the necessary processes required for finishing of an automobile along with the corrosion protection measures. Automobiles contains a variety of engineering materials, engine main body fuel tanks connecting rods heat radiators and other mechanical parts are made from different types of engineering alloys having varying chemical compositions. Other parts like dashboard, front panel and other are made from composites. The main body made from cold roll ed steel having various contours 'c' it due to the different designs is the potential site for corrosion attack, The main body is exposed to the hostile environment through out its life period. An automobile is given a particular finish with a view to counter the hostile environments as they are not limited for plying in a limiting conditions and are taken to different weather conditions in one day thus facing severe stresses and strain. Thus it is essential that an automobile before rolling 'out of the assembly line should properly corrosion resistant and aesthetically pleasant also. Finishing for automobiles being very specialized, the main requirement being maximum durability with minimum numbers of coats baked, at the fastest possible schedule. High gloss and range of good eye catching colours being important to increase sales appeal. In the near past the car finishes were based on alkyd-amino resins baking materials and force drying lacquers, which have excellent appearance originally and maintain it on aging. The finishing system for the synthetic baking type may consist of

9 CFR 318.309 - Finished product inspection.

Science.gov (United States)

2010-01-01

... Section 318.309 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY... Canning and Canned Products § 318.309 Finished product inspection. (a) Finished product inspections must...

Nearly Finished Genomes Produced Using Gel Microdroplet Culturing (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

Energy Technology Data Exchange (ETDEWEB)

Fitzsimmons, Michael

2012-06-01

Michael Fitzsimmons from Los Alamos National Laboratory gives a talk titled "Nearly Finished Genomes Produced Using Gel Microdroplet Culturing" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Activated sludge respirometry to assess solar detoxification of a metal finishing effluent

International Nuclear Information System (INIS)

Santos-Juanes, L.; Amat, A.M.; Arques, A.; Bernabeu, A.; Silvestre, M.; Vicente, R.; Ano, E.

2008-01-01

Inhibition of the respiration of activated sludge has been tested as a convenient method to estimate toxicity of aqueous solutions containing copper and cyanide, such as metal finishing effluents; according to this method, an EC 50 of 0.5 mg/l was determined for CN - and 3.0 mg/l for copper. Solar detoxification of cyanide-containing solutions was studied using TiO 2 , but this process was unfavourable because of the inhibitory role that plays the copper ions present in real effluents on the oxidation of cyanide. On the other hand, the oxidative effect of hydrogen peroxide was greatly enhanced by Cu 2+ and solar irradiation, as complete elimination of free and complexed cyanide could be accomplished, together with precipitation of copper, in experiments carried out at pilot plant scale with real metal finishing effluents. Under these conditions, total detoxification was achieved according to respirometric measurements although some remaining toxicity was determined by more sensitive Vibrio fischeri luminescent assay

Activated sludge respirometry to assess solar detoxification of a metal finishing effluent

Energy Technology Data Exchange (ETDEWEB)

Santos-Juanes, L.; Amat, A.M. [Departamento de Ingenieria Textil y Papelera, Escuela Politecnica Superior de Alcoy, Universidad Politecnica de Valencia, Plaza Ferrandiz y Carbonell s/n, E-03801 Alcoy (Spain); Arques, A. [Departamento de Ingenieria Textil y Papelera, Escuela Politecnica Superior de Alcoy, Universidad Politecnica de Valencia, Plaza Ferrandiz y Carbonell s/n, E-03801 Alcoy (Spain)], E-mail: aarques@txp.upv.es; Bernabeu, A.; Silvestre, M.; Vicente, R. [Departamento de Ingenieria Textil y Papelera, Escuela Politecnica Superior de Alcoy, Universidad Politecnica de Valencia, Plaza Ferrandiz y Carbonell s/n, E-03801 Alcoy (Spain); Ano, E. [Departamento de Gestion e Innovacion, Area de producto y desarrollo sostenible, Asociacion de Investigacion de la Industria del Juguete, Conexas y Afines (AIJU), Avda. de la industria, 23, 03440 Ibi (Spain)], E-mail: m.ambiente@aiju.info

2008-05-30

Inhibition of the respiration of activated sludge has been tested as a convenient method to estimate toxicity of aqueous solutions containing copper and cyanide, such as metal finishing effluents; according to this method, an EC{sub 50} of 0.5 mg/l was determined for CN{sup -} and 3.0 mg/l for copper. Solar detoxification of cyanide-containing solutions was studied using TiO{sub 2}, but this process was unfavourable because of the inhibitory role that plays the copper ions present in real effluents on the oxidation of cyanide. On the other hand, the oxidative effect of hydrogen peroxide was greatly enhanced by Cu{sup 2+} and solar irradiation, as complete elimination of free and complexed cyanide could be accomplished, together with precipitation of copper, in experiments carried out at pilot plant scale with real metal finishing effluents. Under these conditions, total detoxification was achieved according to respirometric measurements although some remaining toxicity was determined by more sensitive Vibrio fischeri luminescent assay.

CSER 00-003: Criticality Safety Evaluation report for PFP Magnesium Hydroxide Precipitation Process for Plutonium Stabilization Glovebox 3

International Nuclear Information System (INIS)

LAN, J.S.

2000-01-01

This Criticality Safety Evaluation Report analyzes the stabilization of plutonium/uranium solutions in Glovebox 3 using the magnesium hydroxide precipitation process at PFP. The process covered are the receipt of diluted plutonium solutions into three precipitation tanks, the precipitation of plutonium from the solution, the filtering of the plutonium precipitate from the solution, the scraping of the precipitate from the filter into boats, and the initial drying of the precipitated slurry on a hot plate. A batch (up to 2.5 kg) is brought into the glovebox as plutonium nitrate, processed, and is then removed in boats for further processing. This CSER establishes limits for the magnesium hydroxide precipitation process in Glovebox 3 to maintain criticality safety while handling fissionable material

[Experimental analysis of finishing lines in ceramometal restorations].

Science.gov (United States)

Gascón, F; Gil, J A; Fons, A; Badal, R

1990-11-01

The preparation is the first step of any tooth reconstruction. The biological integration of the protesis is depending on the marginal adaptation (finish line of the preparation), occlusal adaptation (occlusal reduction), longevity of the restoration (retention and luting) and esthetics. The effect the two finish line of the preparation is studied using experimental design. In porcelain-fused-to-metal the finish line of the preparation in chanfer is superior at the beveled shoulder, because proportioning better marginal adaptation.

16 CFR 1508.7 - Construction and finishing.

Science.gov (United States)

2010-01-01

... REGULATIONS REQUIREMENTS FOR FULL-SIZE BABY CRIBS § 1508.7 Construction and finishing. (a) All wood surfaces shall be smooth and free from splinters. (b) All wood parts shall be free from splits, cracks, or other... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Construction and finishing. 1508.7 Section...

Prediction of manure nitrogen and carbon output from grower-finisher pigs

DEFF Research Database (Denmark)

Vu Thi Khanh, Van; Prapaspongsa, Trakarn; Poulsen, Hanne Damgaard

2009-01-01

Intensive pig production may be a hazard to the environment due to plant nutrient leakage and losses. To facilitate efficient and sustainable manure management and reduce oversupplying of crops with nutrients, there is a need for precise assessment of nutrient content in manure and manure excretion....... This study has developed algorithms for predicting the amount of excreta and manure content of nitrogen (N) and carbon (C). Data compiled from 285 digestibility and N balance experiments with growing-finishing pigs diets fed diets varying widely in chemical composition were used to establish algorithms...

Purification and Structural and Kinetic Characterization of the Pyrophosphate:Fructose-6-Phosphate 1-Phosphotransferase from the Crassulacean Acid Metabolism Plant, Pineapple.

Science.gov (United States)

Tripodi, KEJ.; Podesta, F. E.

1997-03-01

Pyrphosphate-dependent phosphofructokinase (PFP) was purified to electrophoretic homogeneity from illuminated pineapple (Ananas comosus) leaves. The purified enzyme consists of a single subunit of 61.5 kD that is immunologically related to the potato tuber PFP [beta] subunit. The native form of PFP likely consists of a homodimer of 97.2 kD, as determined by gel filtration. PFP's glycolytic activity was strongly dependent on pH, displaying a maximum at pH 7.7 to 7.9. Gluconeogenic activity was relatively constant between pH 6.7 and 8.7. Activation by Fru-2,6-bisphosphate (Fru-2,6-P2) was dependent on assay pH. In the glycolytic direction, it activated about 10-fold at pH 6.7, but only 2-fold at pH 7.7. The gluconeogenic reaction was only weakly affected by Fru-2,6-P2. The true substrates for the PFP forward and reverse reactions were Fru-6-phosphate and Mg-pyrophosphate, and Fru-1,6-P2, orthophosphate, and Mg2+, respectively. The results suggest that pineapple PFP displays regulatory properties consistent with a pH-based regulation of its glycolytic activity, in which a decrease in cytosolic pH caused by nocturnal acidification during Crassulacean acid metabolism, which could curtail its activity, is compensated by a parallel increase in its sensitivity to Fru-2,6-P2. It is also evident that the [beta] subunit alone is sufficient to confer PFP with a high catalytic rate and the regulatory properties associated with activation by Fru-2,6-P2.

16 CFR 1509.8 - Construction and finishing.

Science.gov (United States)

2010-01-01

... REGULATIONS REQUIREMENTS FOR NON-FULL-SIZE BABY CRIBS § 1509.8 Construction and finishing. (a) All wood surfaces of non-full-size baby cribs shall be smooth and free from splinters. (b) All wood parts of non... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Construction and finishing. 1509.8 Section...

Experimental investigation on shore hardness of barrel-finished ...

Indian Academy of Sciences (India)

Rupinder Singh

2017-08-02

Aug 2, 2017 ... Barrel finishing (BF) process is widely used to improve the surface finish and dimensional features of metallic and ... plastic-based waste can be easily recycled. However .... The pattern prepared with solid density has a dense.

Surface Finish after Laser Metal Deposition

Science.gov (United States)

Rombouts, M.; Maes, G.; Hendrix, W.; Delarbre, E.; Motmans, F.

Laser metal deposition (LMD) is an additive manufacturing technology for the fabrication of metal parts through layerwise deposition and laser induced melting of metal powder. The poor surface finish presents a major limitation in LMD. This study focuses on the effects of surface inclination angle and strategies to improve the surface finish of LMD components. A substantial improvement in surface quality of both the side and top surfaces has been obtained by laser remelting after powder deposition.

The 1.8-Å resolution crystal structure of YDR533Cp from Saccharomyces cerevisiae: A member of the DJ-1/ThiJ/PfpI superfamily

Science.gov (United States)

Wilson, Mark A.; Amour, Courtney V. St.; Collins, Jennifer L.; Ringe, Dagmar; Petsko, Gregory A.

2004-01-01

The yeast gene YDR533C encodes a protein belonging to the DJ-1/ThiJ/PfpI superfamily. This family includes the human protein DJ-1, which is mutated in autosomal recessive early-onset Parkinson's disease. The function of DJ-1 and its yeast homologue YDR533Cp is unknown. We report here the crystal structure of YDR533Cp at 1.8-Å resolution. The structure indicates that the closest relative to YDR533Cp is the Escherichia coli heat shock protein Hsp31 (YedU), which has both chaperone and protease activity. As expected, the overall fold of the core domain of YDR533Cp is also similar to that of DJ-1 and the bacterial protease PfpI. YDR533Cp contains a possible catalytic triad analogous to that of Hsp31 and an additional domain that is present in Hsp31 but is not seen in DJ-1 and other members of the family. The cysteine in this triad (Cys-138) is oxidized in this crystal structure, similar to modifications seen in the corresponding cysteine in the crystal structure of DJ-1. YDR533Cp appears to be a dimer both in solution and the crystal, but this dimer is formed by a different interface than that found in Hsp31 or other members of the superfamily. PMID:14745011

IMPLEMENTING CHANGES TO AN APPROVED AND IN-USE DOCUMENTED SAFETY ANALYSIS

International Nuclear Information System (INIS)

KING JP

2008-01-01

The Plutonium Finishing Plant (PFP) has refined a process to ensure a comprehensive and complete DSA/TSR change implementation. Successful Nuclear Facility Safety Basis implementation is essential to avoid creating a Potential Inadequacy in Safety Analysis (PISA) situation, or implementing a facility into a non-compliance that can result in a TSR violation. Once past initial implementation, additional changes to Documented Safety Analysis (DSA) and Technical Safety Requirements (TSRs) are often needed due to needed requirement clarifications, operating experience indicating that Conditions/Required Actions/Surveillance Requirements could be improved, changes in facility conditions, or changes in facility mission etc. An effective change implementation process is essential to ensuring compliance with 10 CFR 830.202(a), 'The contractor responsible for a hazard category 1,2, or 3 DOE nuclear facility must establish and maintain the safety basis for the facility'

Response of TLD-albedo and nuclear track dosimeters exposed to plutonium sources

International Nuclear Information System (INIS)

Brackenbush, L.W.; Baumgartner, W.V.; Fix, J.J.

1991-12-01

Neutron dosimetry has been extensively studied at Hanford since the mid-1940s. At the present time, Hanford contractors use thermoluminescent dosimeter (TLD)-albedo dosimeters to record the neutron dose equivalent received by workers. The energy dependence of the TLD-albedo dosimeter has been recognized and documented since introduced at Hanford in 1964 and numerous studies have helped assure the accuracy of dosimeters. With the recent change in Hanford's mission, there has been a significant decrease in the handling of plutonium tetrafluoride, and an increase in the handling of plutonium metal and plutonium oxide sources. This study was initiated to document the performance of the current Hanford TLD-albedo dosimeter under the low scatter conditions of the calibration laboratory and under the high scatter conditions in the work place under carefully controlled conditions at the Plutonium Finishing Plant (PFP). The neutron fields at the PFP facility were measured using a variety of instruments, including a multisphere spectrometer, tissue equivalent proportional counters, and specially calibrated rem meters. Various algorithms were used to evaluate the TLD-albedo dosimeters, and the results are given in this report. Using current algorithms, the dose equivalents evaluated for bare sources and sources with less than 2.5 cm (1 in.) of acrylic plastic shielding in high scatter conditions typical of glove box operations are reasonably accurate. Recently developed CR-39 track etch dosimeters (TEDs) were also exposed in the calibration laboratory and at the PFP. The results indicate that the TED dosimeters are quite accurate for both bare and moderated neutron sources. Until personnel dosimeter is available that incorporates a direct measure of the neutron dose to a person, technical uncertainties in the accuracy of the recorded data will continue

Response of TLD-albedo and nuclear track dosimeters exposed to plutonium sources

Energy Technology Data Exchange (ETDEWEB)

Brackenbush, L.W.; Baumgartner, W.V.; Fix, J.J.

1991-12-01

Neutron dosimetry has been extensively studied at Hanford since the mid-1940s. At the present time, Hanford contractors use thermoluminescent dosimeter (TLD)-albedo dosimeters to record the neutron dose equivalent received by workers. The energy dependence of the TLD-albedo dosimeter has been recognized and documented since introduced at Hanford in 1964 and numerous studies have helped assure the accuracy of dosimeters. With the recent change in Hanford`s mission, there has been a significant decrease in the handling of plutonium tetrafluoride, and an increase in the handling of plutonium metal and plutonium oxide sources. This study was initiated to document the performance of the current Hanford TLD-albedo dosimeter under the low scatter conditions of the calibration laboratory and under the high scatter conditions in the work place under carefully controlled conditions at the Plutonium Finishing Plant (PFP). The neutron fields at the PFP facility were measured using a variety of instruments, including a multisphere spectrometer, tissue equivalent proportional counters, and specially calibrated rem meters. Various algorithms were used to evaluate the TLD-albedo dosimeters, and the results are given in this report. Using current algorithms, the dose equivalents evaluated for bare sources and sources with less than 2.5 cm (1 in.) of acrylic plastic shielding in high scatter conditions typical of glove box operations are reasonably accurate. Recently developed CR-39 track etch dosimeters (TEDs) were also exposed in the calibration laboratory and at the PFP. The results indicate that the TED dosimeters are quite accurate for both bare and moderated neutron sources. Until personnel dosimeter is available that incorporates a direct measure of the neutron dose to a person, technical uncertainties in the accuracy of the recorded data will continue.

Response of TLD-albedo and nuclear track dosimeters exposed to plutonium sources

Energy Technology Data Exchange (ETDEWEB)

Brackenbush, L.W.; Baumgartner, W.V.; Fix, J.J.

1991-12-01

Neutron dosimetry has been extensively studied at Hanford since the mid-1940s. At the present time, Hanford contractors use thermoluminescent dosimeter (TLD)-albedo dosimeters to record the neutron dose equivalent received by workers. The energy dependence of the TLD-albedo dosimeter has been recognized and documented since introduced at Hanford in 1964 and numerous studies have helped assure the accuracy of dosimeters. With the recent change in Hanford's mission, there has been a significant decrease in the handling of plutonium tetrafluoride, and an increase in the handling of plutonium metal and plutonium oxide sources. This study was initiated to document the performance of the current Hanford TLD-albedo dosimeter under the low scatter conditions of the calibration laboratory and under the high scatter conditions in the work place under carefully controlled conditions at the Plutonium Finishing Plant (PFP). The neutron fields at the PFP facility were measured using a variety of instruments, including a multisphere spectrometer, tissue equivalent proportional counters, and specially calibrated rem meters. Various algorithms were used to evaluate the TLD-albedo dosimeters, and the results are given in this report. Using current algorithms, the dose equivalents evaluated for bare sources and sources with less than 2.5 cm (1 in.) of acrylic plastic shielding in high scatter conditions typical of glove box operations are reasonably accurate. Recently developed CR-39 track etch dosimeters (TEDs) were also exposed in the calibration laboratory and at the PFP. The results indicate that the TED dosimeters are quite accurate for both bare and moderated neutron sources. Until personnel dosimeter is available that incorporates a direct measure of the neutron dose to a person, technical uncertainties in the accuracy of the recorded data will continue.

Finishing of the cold mass assembly

CERN Multimedia

Patrice Loïez

2001-01-01

Photo 1 Technicians are putting in order the instrumentation wires. The prototype magnets were equipped with numerous sensors to monitor key parameters during the performance tests at cold conditions. Photo 2 The cold mass assembly is resting on special supports in order to allow the finishing operations. Technicians are putting in order the instrumentation wires. The prototype magnets were equipped with numerous sensors to monitor key parameters during the performance tests at cold conditions. Photo 3 View of the lyre-side end of the active part assembly. The extremity of the shrinking cylinder has been bevelled in view of welding the end cover. Photo 4 General view of the finishing station showing the special supporting structures (blue and yellow structures) needed for the geometric measurements and for the alignment operations. One can also see the light building surrounding the finishing station, which purpose is to isolate the laser measuring machines from disturbances. Photo 5 The extremity of the shri...

Flexibility of production systems and prepare-finish time

Directory of Open Access Journals (Sweden)

Vukićević Milan R.

2006-01-01

Full Text Available One of the specificities of the large-serial and mass production is the almost neglected percentage of prepare-finish time in the production cycle. In the conditions of today dominant discontinuous production, it becomes a significant element of the production cycle. The eastern (Japan doctrine of increasing the flexibility of the production systems, is based inter alia also on the extreme reduction of the prepare-finish time. For this reason, the aim of this study was to identify the types and percentages of individual jobs within the group of prepare-finish jobs. The sample consisted of 3 (three production systems for the production of joinery, with the discontinuous production system. The research shows that the percentage of time of the jobs installation of work instruments, regulation of processing regime, and removal of work instruments is extremely long and that it ranges between 11.83% and 18.93% of the shift time. The reasons of the high percentage of these jobs are the wide range of products and the absence of the rationalisation of prepare-finish jobs. Within the efforts to minimize the effects of disruption and to increase the flexibility of the production systems, the rationalisation of prepare-finish jobs is the unavoidable condition.

Unit 1 and Unit 2 Nuclear Power Plant Mochovce construction finishing from primary contractor of technological part. Skoda Praha a. s. point of view

International Nuclear Information System (INIS)

Horky, F.

2000-01-01

In this paper the history of delivery of technological part for NPP V-1 Mochovce as well as of reconstruction and safety improvements by the Skoda Praha a.s. is presented. Primary contractor of technological part Skoda Praha together with its final suppliers proved ability to realize under hard conditions such a complicated work what was indisputedly Units 1 and 2 finishing. Company proved capability to conform itself flexibly in the course of work to requirements of customer for realization of safety measures which means that Units 1 and 2 fully satisfy international standards. By fulfilment of primary contractor of technology obligations and above all by takeover of complex responsibility for both Units putting in operation including responsibility for 'past' Skoda Praha put away one of basic problems which occurred in decision making to whom will be assigned construction finishing contract. These facts fully qualify Skoda Praha to be selected for possible Units 3 and 4 construction finishing as one of chief construction finishing participant

40 CFR 63.1347 - Standards for raw and finish mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for raw and finish mills. 63... and Operating Limits § 63.1347 Standards for raw and finish mills. The owner or operator of each new or existing raw mill or finish mill at a facility which is a major source subject to the provisions...

Surface morphology changes of acrylic resins during finishing and polishing phases

Directory of Open Access Journals (Sweden)

Glaucio Serra

2013-12-01

Full Text Available INTRODUCTION: The finishing and polishing phases are essential to improve smoothness and shining on the surface of acrylic resins used to make removable orthodontic appliances. A good surface finishing reduces roughness, which facilitates hygiene, prevents staining and provides greater comfort to the patients. OBJECTIVE: The aim of this paper was to analyze the changes on surface morphology of acrylic resins during finishing and polishing phases. METHODS: Thirty discs (10 mm in diameter and 5 mm in length were made with acrylic resin and randomly divided into ten groups. The control group did not receive any treatment while the other groups received gradual finishing and polishing. The last group received the entire finishing and polishing procedures. Surface morphology was qualitatively analyzed through scanning electron microscopy and quantitatively analyzed through a laser profilometer test. RESULTS: The acrylic resin surfaces without treatment showed bubbles which were not observed in the subsequent phases. Wearing out with multilaminated burs, finishing with wood sandpaper and finishing with water sandpaper resulted in surfaces with decreasing irregularities. The surfaces that were polished with pumice and with low abrasive liquids showed high superficial smoothness. CONCLUSION: Highly smooth acrylic resin surfaces can be obtained after mechanical finishing and polishing performed with multilaminated burs, wood sandpaper, water sandpaper, pumice and low abrasive liquids.

Clear exterior finishes : finding the balance between aesthetics and durability

Science.gov (United States)

Tom Daniel; Marc S. Hirsch; Ken McClelland; Alan S. Ross; R. Sam Williams

2004-01-01

Consumers can easily be confused by the abundance of choices to make when selecting a clear wood finish. There are many types of clear finishes with different characteristics and product claims. This article is designed to help consumers sort out the different finishes and effectively choose which product would be best for their purpose. First, we cover the causes and...

Effects of Fiber Finish on the Performance of Asphalt Binders and Mastics

Directory of Open Access Journals (Sweden)

Bradley J. Putman

2011-01-01

Full Text Available The objective of this study was to determine the effects of finishes applied to polyester fibers on the properties of asphalt binders and mastics. Asphalt binders were mixed with finishes that were extracted from the fibers, and mastics were also made with binder and fibers (with and without finish to isolate the effects of the finish. The results indicated that crude source plays a significant role in how the fiber finish affects the binders and mastics. Additionally different finishes had different effects on binder properties. The major finding of this study is that different polyester fibers, even from the same manufacturer, may not necessarily perform the same in an asphalt mixture. It is important to use fibers that are compatible with the particular asphalt binder that is being used because of the significance of the binder source on the interaction between the finish and the binder.

Prediction method of long-term reliability in improving residual stresses by means of surface finishing

International Nuclear Information System (INIS)

Sera, Takehiko; Hirano, Shinro; Chigusa, Naoki; Okano, Shigetaka; Saida, Kazuyoshi; Mochizuki, Masahito; Nishimoto, Kazutoshi

2012-01-01

Surface finishing methods, such as Water Jet Peening (WJP), have been applied to welds in some major components of nuclear power plants as a counter measure to Primary Water Stress Corrosion Cracking (PWSCC). In addition, the methods of surface finishing (buffing treatment) is being standardized, and thus the buffing treatment has been also recognized as the well-established method of improving stress. On the other hand, the long-term stability of peening techniques has been confirmed by accelerated test. However, the effectiveness of stress improvement by surface treatment is limited to thin layers and the effect of complicated residual stress distribution in the weld metal beneath the surface is not strictly taken into account for long-term stability. This paper, therefore, describes the accelerated tests, which confirmed that the long-term stability of the layer subjected to buffing treatment was equal to that subjected to WJP. The long-term reliability of very thin stress improved layer was also confirmed through a trial evaluation by thermal elastic-plastic creep analysis, even if the effect of complicated residual stress distribution in the weld metal was excessively taken into account. Considering the above findings, an approach is proposed for constructing the prediction method of the long-term reliability of stress improvement by surface finishing. (author)

21 CFR 181.26 - Drying oils as components of finished resins.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Drying oils as components of finished resins. 181... Prior-Sanctioned Food Ingredients § 181.26 Drying oils as components of finished resins. Substances classified as drying oils, when migrating from food-packaging material (as components of finished resins...

Wall Finishes; Carpentry: 901895.

Science.gov (United States)

Dade County Public Schools, Miami, FL.

The course outline is designed to provide instruction in selecting, preparing, and installing wall finishing materials. Prerequisites for the course include mastery of building construction plans, foundations and walls, and basic mathematics. Intended for use in grades 11 and 12, the course contains five blocks of study totaling 135 hours of…

Technology of magnetic abrasive finishing in machining of difficult-to-machine alloy complex surface

Directory of Open Access Journals (Sweden)

Fujian MA

2016-10-01

Full Text Available The technology of magnetic abrasive finishing is one of the important finishing technologies. Combining with low-frequency vibration and ultrasonic vibration, it can attain higher precision, quality and efficiency. The characteristics and the related current research of magnetic abrasive finishing, vibration assisted magnetic abrasive finishing and ultrasonic assisted magnetic abrasive finishing are introduced. According to the characteristics of the difficult-to-machine alloy's complex surface, the important problems for further study are presented to realize the finishing of complex surface with the technology of magnetic abrasive finishing, such as increasing the machining efficiency by enhancing the magnetic flux density of machining gap and compounding of magnetic energy and others, establishing of the control function during machining and the process planning method for magnetic abrasive finishing of complex surface under the space geometry restraint of complex surface on magnetic pole, etc.

Data quality objectives for moisture measurement in stabilized special nuclear material

International Nuclear Information System (INIS)

Weier, D.R.; Pulsipher, B.A.; Silvers, K.L.

2000-01-01

Data Quality Objectives methodology is applied to Loss-on-Ignition (LOI) moisture content testing for stabilized nuclear materials. This work was performed by Pacific Northwest National Laboratory in support of the Plutonium Finishing Plant (PFP)/Fluor Hanford, Inc. Historical results on LOI test results for two material types, oxide and sludge, are used to estimate within container variability. This variability estimate is then used in formulating the two recommended acceptance criteria for containers of material. The criteria which follow are proposed to replace the current criterion, which requires recycle if either of two container LOI measurements exceed 0.5 wt%, the DOE Standard 3013-99 threshold value. (1) The 95% upper confidence limit (UCL) for the true mean underlying moisture content in the container material should be less than 0.5 wt%. (2) The difference between the two LOI measurements per container should not exceed their expected 95th percentile relative to the estimated variability. Containers not meeting the first criterion, or those that generate in any negative LOI result, require material recycle. Containers not meeting the second criteria require review of the measurement results, potentially leading to resampling and retesting. Data from Los Alamos National Laboratory studies on moisture testing are obtained and analyzed. The performance of Supercritical Fluid Extraction (SFE), which will soon be implemented at the PFP, is described for several material types. This information will be used to establish initial acceptance criteria when SFE comes on line

CONTAMINATED PROCESS EQUIPMENT REMOVAL FOR THE DECOMMISSIONG AND DECONTAMINATION OF THE 232-Z CONTAMINATED WASTE RECOVERY PROCESS FACILITY AT THE PLUTONIUM FINISHING PLANT

International Nuclear Information System (INIS)

HOPKINS, A.M.; MINETTE, M.J.; KLOS, D.B.

2007-01-01

This paper describes the unique challenges encountered and subsequent resolutions to accomplish the deactivation and decontamination of a plutonium ash contaminated building. The 232-Z Contaminated Waste Recovery Process Facility at the Plutonium Finishing Plant was used to recover plutonium from process wastes such as rags, gloves, containers and other items by incinerating the items and dissolving the resulting ash. The incineration process resulted in a light-weight plutonium ash residue that was highly mobile in air. This light-weight ash coated the incinerator's process equipment, which included gloveboxes, blowers, filters, furnaces, ducts, and filter boxes. Significant airborne contamination (over 1 million derived air concentration hours [DAC]) was found in the scrubber cell of the facility. Over 1300 grams of plutonium held up in the process equipment and attached to the walls had to be removed, packaged and disposed. This ash had to be removed before demolition of the building could take place

Performance and cost implication of finisher turkeys fed varying ...

African Journals Online (AJOL)

A 28-day experiment was conducted to determine the effect of feeding varying levels of rice milling waste as a substitute on maize on the performance, nutrient utilization and the economics implication on finisher turkeys. Five turkey finisher diets were formulated by substituting maize with rice milling waste at 0%, 25%, 50%, ...

Surface texture of resin-modified glass ionomer cements: effects of finishing/polishing time.

Science.gov (United States)

Yap, A U J; Ong, S B; Yap, W Y; Tan, W S; Yeo, J C

2002-01-01

This study compared the surface texture of resin-modified glass ionomer cements after immediate and delayed finishing with different finishing/polishing systems. Class V preparations were made on the buccal and lingual/palatal surfaces of 64 freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (GC) and Photac-Fil Quick (3M-ESPE) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with 8-fluted tungsten carbide burs. The teeth were then randomly divided into four groups of 16 teeth. Half of the teeth in each group were finished immediately, while the remaining half were finished after one-week storage in distilled water at 37 degrees C. The following finishing/polishing systems were employed: (a) Robot Carbides; (b) Super-Snap system; (c) OneGloss and (d) CompoSite Polishers. The mean surface roughness (microm; n=8) in vertical (RaV) and horizontal (RaH) axis was measured using a profilometer. Data was subjected to ANOVA/Scheffe's tests and Independent Samples t-test at significance level 0.05. Ra values were generally lower in both vertical and horizontal axis with delayed finishing/polishing. Although significant differences in RaV and RaH values were observed among several systems with immediate finishing/polishing, only one (Fuji II LC: RaH - Super-Snap < Robot Carbides) was observed with delayed finishing.

Orthodontic treatment outcomes obtained by application of a finishing protocol

Directory of Open Access Journals (Sweden)

Alvaro Carvajal-Flórez

2016-04-01

Full Text Available ABSTRACT Objective: To evaluate the results of a finishing protocol implemented in patients treated in the Orthodontics graduate program at Universidad de Antioquia. Evaluation was carried out by means of the criteria set by the Objective Grading System (OGS of the American Board of Orthodontics (ABO. Methods: Cast models and panoramic radiographs of 34 patients were evaluated. The intervention group (IG consisted of 17 patients (19.88 ± 4.4 years old treated under a finishing protocol. This protocol included training in finishing, application of a finishing guide, brackets repositioning and patient's follow-up. Results of the IG were compared to a control group of 17 patients (21.88 ± 7.0 years old selected by stratified randomization without finishing intervention (CG. Results: The scores for both CG and IG were 38.00 ± 9.0 and 31.41 ± 9.6 (p = 0.048, respectively. The score improved significantly in the IG group, mainly regarding marginal ridges (CG: 5.59 ± 2.2; IG: 3.65 ± 1.8 (p = 0.009 and root angulation (CG: 7.59 ± 2.8; IG: 4.88 ± 2.6 (p = 0.007. Criteria that did not improve, but had the highest scores were: alignment (CG: 6.35 ± 2.7; IG: 6.82 ± 2.8 (p = 0.62 and buccolingual inclination (CG: 3.6 ± 5.88; IG: 5.29 ± 3.9 (p = 0.65. Conclusions: Standardization and implementation of a finishing protocol contributed to improve clinical performance in the Orthodontics graduate program, as expressed by occlusal outcomes. Greater emphasis should be given on the finishing phase to achieve lower scores in the ABO grading system.

DESIGN OF FILL AND FINISH FACILITY FOR ACTIVE PHARMACEUTICAL INGREDIENTS (API

Directory of Open Access Journals (Sweden)

NUUR LAILA KHAIRUDDIN

2016-08-01

Full Text Available Fill and finish operations continue to be one of the most heavily outsourced activities in the biopharmaceutical manufacturing market today. There are a few aspects that need to be consider in outsource activities like logistic, storage condition, facility certification and audit as regulations and standards which the manufacturer should adhere. Risk would be greater and extra care should be taken when outsource from foreign fill and finish facility. Thus, the internal aseptic fill and finish facility with audit checklist will help to minimize the risk during logistic and storage and also minimize the cost for outsource fill and finish facility. The data collections are through survey and conceptual design with simulation as the execution part.

The costs of completing unfinished US nuclear power plants

International Nuclear Information System (INIS)

Feldman, S.L.; Bernstein, M.A.; Noland, R.B.

1988-01-01

A cost benefit analysis is performed to assess the costs of completing unfinished nuclear power plants in four regions of the United States of America, (north-east, south-east, mid-west and west). The analysis is in five main sections: the projection of the cost to complete nuclear plants under construction, the forecast of future operations and maintenance costs, the forecast of price of fuels, the evaluation of future electricity demand and capacity growth, and calculation of the financial cost-benefit ratio based on the preceding figures. It was found that in the north-east, mid-west and west, because the demand for the power will not be made before the year 2000, finishing the units is not the least-cost supply option. Therefore, most of the units should not be finished unless over 90% completed already, in which case it may be cost-effective to finish them. (author)

Efficacy of 2 finishing protocols in the quality of orthodontic treatment outcome.

Science.gov (United States)

Stock, Gregory J; McNamara, James A; Baccetti, Tiziano

2011-11-01

The objectives of this prospective clinical study were to evaluate the quality of treatment outcomes achieved with a complex orthodontic finishing protocol involving serpentine wires and a tooth positioner, and to compare it with the outcomes of a standard finishing protocol involving archwire bends used to detail the occlusion near the end of active treatment. The complex finishing protocol sample consisted of 34 consecutively treated patients; 1 week before debonding, their molar bands were removed, and serpentine wires were placed; this was followed by active wear of a tooth positioner for up to 1 month after debonding. The standard finishing protocol group consisted of 34 patients; their dental arches were detailed with archwire bends and vertical elastics. The objective grading system of the American Board of Orthodontics was used to quantify the quality of the finish at each time point. The Wilcoxon signed rank test was used to compare changes in the complex finishing protocol; the Mann-Whitney U test was used to compare changes between groups. The complex finishing protocol group experienced a clinically significant improvement in objective grading system scores after treatment with the positioner. Mild improvement in posterior space closure was noted after molar band removal, but no improvement in the occlusion was observed after placement of the serpentine wires. Patients managed with the complex finishing protocol also had a lower objective grading system score (14.7) at the end of active treatment than did patients undergoing the standard finishing protocol (23.0). Tooth positioners caused a clinically significant improvement in interocclusal contacts, interproximal contacts, and net objective grading system score; mild improvement in posterior band space was noted after molar band removal 1 week before debond. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Relevance of microbial finished product testing in food safety management

DEFF Research Database (Denmark)

Zwietering, Marcel H.; Jacxsens, Liesbeth; Membré, Jeanne Marie

2016-01-01

Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food......-active way by implementing an effective food safety management system. For verification activities in a food safety management system, finished product testing may however be useful. For three cases studies; canned food, chocolate and cooked ham, the relevance of testing both of finished products....... If a hazardous organism is found it means something, but absence in a limited number of samples is no guarantee of safety of a whole production batch. Finished product testing is often too little and too late. Therefore most attention should be focussed on management and control of the hazards in a more pro...

Enhancing Surface Finish of Additively Manufactured Titanium and Cobalt Chrome Elements Using Laser Based Finishing

Science.gov (United States)

Gora, Wojciech S.; Tian, Yingtao; Cabo, Aldara Pan; Ardron, Marcus; Maier, Robert R. J.; Prangnell, Philip; Weston, Nicholas J.; Hand, Duncan P.

Additive manufacturing (AM) offers the possibility of creating a complex free form object as a single element, which is not possible using traditional mechanical machining. Unfortunately the typically rough surface finish of additively manufactured parts is unsuitable for many applications. As a result AM parts must be post-processed; typically mechanically machined and/or and polished using either chemical or mechanical techniques (both of which have their limitations). Laser based polishing is based on remelting of a very thin surface layer and it offers potential as a highly repeatable, higher speed process capable of selective area polishing, and without any waste problems (no abrasives or liquids). In this paper an in-depth investigation of CW laser polishing of titanium and cobalt chrome AM elements is presented. The impact of different scanning strategies, laser parameters and initial surface condition on the achieved surface finish is evaluated.

Population dynamics of swine influenza virus in finishing pigs

NARCIS (Netherlands)

Loeffen, W.L.A.

2008-01-01

Influenza virus infections in swine were first noticed in the US in 1918, during the human pandemic of the Spanish flu. In Europe, seroprevalences for the three most common swine influenza strains at the moment, H1N1, H3N2 and H1N2, range from 20-80% in finishing pigs at the end of the finishing

Bonding of radioactive contamination. IV. Effect of surface finish

International Nuclear Information System (INIS)

Rankin, W.N.

1983-01-01

The mechanisms by which radioactive contamination would be bonded to a DWPF canister are being investigated. Previous investigations in this series have examined the effects of temperature, oxidation before contamination, and atmosphere composition control on the bonding of contamination. This memorandum describes the results of tests to determine the effect of special surface finishes on the bonding of contamination to waste glass canisters. Surface pretreatments which produce smoother canister surfaces actually cause radioactive contamination to be more tightly bonded to the metal surface than on an untreated surface. Based on the results of these tests it is recommended that the canister surface finish be specified as having a bright cold rolled mill finish equivalent to ASTM No. 2B. 7 references, 3 figures, 3 tables

Study on interfacial reaction between lead-free solders and alternative surface finishes

International Nuclear Information System (INIS)

Siti Rabiatul Aisha; Ourdjini, A.; Saliza Osman

2007-01-01

This study investigates the interfacial reactions occurring during reflow soldering between Sn-Ag-Cu lead-free solder and two surface finishes: electroless nickel/ immersion gold (ENIG) and immersion silver (IAg). The study focuses on interfacial reactions evolution and growth kinetics of intermetallic compounds (IMC) formed during soldering and isothermal ageing at 150 degree Celsius for up to 2000 hours. Optical and scanning electron microscopy were used to measure IMC thickness and examine the morphology of IMC respectively, whereas the IMC phases were identified by energy dispersive X-ray analysis (EDX). The results showed that the IMC formed on ENIG finish is thinner compared to that formed on IAg finish. For IAg surface finish, Cu 6 Sn 5 IMCs with scallop morphology are formed at the solder/ surface finish interface after reflow while a second IMC, Cu 3 Sn was formed between the copper and Cu 6 Sn 5 IMC after the isothermal ageing treatment. For ENIG surface finish both (Cu,Ni) 6 Sn 5 and (Ni,Cu) 3 Sn 4 are formed after soldering. Isothermal aging of the solder joints formed on ENIG finish was found to have a significant effect on the morphology of the intermetallics by transforming to more spherical and denser morphology in addition to increase i their thickness with increased ageing time. (author)

The Successful Utilization Of Commercial Treatment Capabilities To Disposition Hanford's No-Path-Forward Suspect Transuranic Wastes

International Nuclear Information System (INIS)

Blackford, L.T.; Catlow, R.L.; West, L.D.; Collins, M.S.; Romine, L.D.; Moak, D.J.

2012-01-01

The U.S. Department of Energy (DOE) Richland Operations Office (RL) has adopted the 2015 Vision for Cleanup of the Hanford Site. The CH2M HILL Plateau Remediation Company's (CHPRC) Waste and Fuels Management Project (W and FMP) and their partners support this mission by providing centralized waste management services for the Hanford Site waste generating organizations. At the time of the CHPRC contract award (August 2008) slightly more than 9,000 cubic meters (m 3 ) of legacy waste was defined as ''no-path-forward waste.'' A significant portion of this waste (7,650 m 3 ) comprised wastes with up to 50 grams of special nuclear materials (SNM) in oversized packages recovered during retrieval operations and large glove boxes removed from Hanford's Plutonium Finishing Plant (PFP). Through a collaborative effort between the DOE, CHPRC, and Perma-Fix Environmental Services, Inc. (PESI), pathways for these problematic wastes were developed and are currently being implemented.

Assessment of the Nutrient Contents of Finished Broiler Starter and ...

African Journals Online (AJOL)

The study was conducted to assess and compare the proximate composition and amino acid profile of six (6) finished broiler starter and finisher diets with recommendations of National Research Council (NRC) nutrient requirements table for the different physiological age growth stage. Four samples of each feed type were ...

Monitoring and control of fine abrasive finishing processes

DEFF Research Database (Denmark)

Lazarev, Ruslan

In engineering, surfaces with specified functional properties are of high demand in various applications. Desired surface finish can be obtained using several methods. Abrasive finishing is one of the most important processes in the manufacturing of mould and dies tools. It is a principal method ...... was segmented using discretization methods. The applied methodology was proposed for implementation as an on-line system and is considered to be a part of the next generation of STRECON NanoRAP machine....... to remove unwanted material, obtain desired geometry, surface quality and surface functional properties. The automation and computerization of finishing processes involves utilisation of robots, specialized machines with several degrees of freedom, sensors and data acquisition systems. The focus...... of this work was to investigate foundations for process monitoring and control methods in application to semi-automated polishing machine based on the industrial robot. The monitoring system was built on NI data acquisition system with two sensors, acoustic emission sensor and accelerometer. Acquired sensory...

DEPRESIÓN EN VIGOR POR ENDOGAMIA Y HETEROSIS PARA EL RENDIMIENTO Y SUS COMPONENTES EN ZAPALLO Cucurbita moschata Duch. Ex Poir INBREEDING DEPRESSION AND HETEROSIS FOR YIELD AND ITS COMPONENTS IN PUMPKIN Cucurbita moschata Duch. Ex Poir

Directory of Open Access Journals (Sweden)

Miguel Mariano Espitia Camacho

2006-06-01

Full Text Available El estudio tuvo como objetivos estimar la depresión por endogamia (DE y cuatro tipos de heterosis: promedio general (HP, promedio de progenitores (HM, heterobeltiosis (HB y útil (HU, en dos dialélos [uno entre cinco variedades (V y el otro entre cinco líneas endogamicas S1 (LS1, derivadas de éstas], para el rendimiento por planta (PFP, número de frutos por planta (NFP y peso promedio de fruto (PPF. Los 30 genotipos se evaluaron en el municipio de Candelaria (Valle del Cauca, Colombia, en un diseño de bloques completos al azar con cinco repeticiones. Se presentaron diferencias significativas (p 40 % y HU (>60 % en PFP.With the goal of estimating inbreeding depression (DE and the four types of heterosis: general average (HP, mean (HM, heterobeltiosis (HB and standard (HU, in two diallelic [one among five cross pollinated varieties (VAR and the other among five self-pollinated lines S1(LS1, derived from these], for yield/plant (PFP, number of fruits/plant (NFP and weight/fruit (PPF. The 30 genotypes were evaluated using a complete randomized design with five replicates in Candelaria (Valle del Cauca, Colombia . Significant differences (p 40 % and HU (>60 % in PFP.

Transport losses in finisher pigs: impact of transport distance and season of the year

Directory of Open Access Journals (Sweden)

Eva Voslarova

2017-01-01

Full Text Available Objective The death of animals during transport for slaughter is a major factor indicating the level of welfare in transported animals. The aim of this study was to assess mortality related to the commercial transport of finisher pigs for slaughter in the Czech Republic. Methods The inspectors of the State Veterinary Administration of the Czech Republic recorded the numbers of finisher pigs transported to processing plants in the Czech Republic for slaughter and the mortality in these pigs in relation to transport in the period from 2009 to 2014. Results Our results show that the likelihood of death losses in transported pigs increases with increasing transport distance. The transport-related mortality ranged from 0.049% in pigs transported for distances below 50 km to 0.145% in pigs transported for distances exceeding 300 km. The impact of external air temperature on the transport-related mortality found in our study clearly shows that current transport practices fail to ensure the welfare of pigs transported under other than moderate weather. Particularly cold temperatures below −2°C were associated with increased death losses in winter transport. Conclusion Despite a decreasing trend in the mortality of finisher pigs transported for slaughter in Europe, our study suggests that current transport conditions are not efficient at ensuring the welfare of pigs during transport for longer distances and the protection of pigs against the negative impact of extreme ambient temperatures. Further research should focus on developing practical guidelines to improve the welfare of pigs in transit accordingly.

Approaches for in silico finishing of microbial genome sequences

Directory of Open Access Journals (Sweden)

Frederico Schmitt Kremer

Full Text Available Abstract The introduction of next-generation sequencing (NGS had a significant effect on the availability of genomic information, leading to an increase in the number of sequenced genomes from a large spectrum of organisms. Unfortunately, due to the limitations implied by the short-read sequencing platforms, most of these newly sequenced genomes remained as “drafts”, incomplete representations of the whole genetic content. The previous genome sequencing studies indicated that finishing a genome sequenced by NGS, even bacteria, may require additional sequencing to fill the gaps, making the entire process very expensive. As such, several in silico approaches have been developed to optimize the genome assemblies and facilitate the finishing process. The present review aims to explore some free (open source, in many cases tools that are available to facilitate genome finishing.

Approaches for in silico finishing of microbial genome sequences.

Science.gov (United States)

Kremer, Frederico Schmitt; McBride, Alan John Alexander; Pinto, Luciano da Silva

The introduction of next-generation sequencing (NGS) had a significant effect on the availability of genomic information, leading to an increase in the number of sequenced genomes from a large spectrum of organisms. Unfortunately, due to the limitations implied by the short-read sequencing platforms, most of these newly sequenced genomes remained as "drafts", incomplete representations of the whole genetic content. The previous genome sequencing studies indicated that finishing a genome sequenced by NGS, even bacteria, may require additional sequencing to fill the gaps, making the entire process very expensive. As such, several in silico approaches have been developed to optimize the genome assemblies and facilitate the finishing process. The present review aims to explore some free (open source, in many cases) tools that are available to facilitate genome finishing.

The Challenges of Preserving Historic Resources During the Deactivation and Decommissioning of Highly Contaminated Historically Significant Plutonium Process Facilities

International Nuclear Information System (INIS)

Hopkins, A.; Minette, M.; Sorenson, D.; Heineman, R.; Gerber, M.; Charboneau, S.; Bond, F.

2006-01-01

The Manhattan Project was initiated to develop nuclear weapons for use in World War II. The Hanford Engineer Works (HEW) was established in eastern Washington State as a production complex for the Manhattan Project. A major product of the HEW was plutonium. The buildings and process equipment used in the early phases of nuclear weapons development are historically significant because of the new and unique work that was performed. When environmental cleanup became Hanford's central mission in 1991, the Department of Energy (DOE) prepared for the deactivation and decommissioning of many of the old process facilities. In many cases, the process facilities were so contaminated, they faced demolition. The National Historic Preservation Act (NHPA) requires federal agencies to evaluate the historic significance of properties under their jurisdiction for eligibility for inclusion in the National Register of Historic Places before altering or demolishing them so that mitigation through documentation of the properties can occur. Specifically, federal agencies are required to evaluate their proposed actions against the effect the actions may have on districts, sites, buildings or structures that are included or eligible for inclusion in the National Register. In an agreement between the DOE's Richland Operations Office (RL), the Washington State Historic Preservation Office (SHPO) and the Advisory Council on Historic Preservation (ACHP), the agencies concurred that the Hanford Site Historic District is eligible for listing on the National Register of Historic Places and that a Site-wide Treatment Plan would streamline compliance with the NHPA while allowing RL to manage the cleanup of the Hanford Site. Currently, many of the old processing buildings at the Plutonium Finishing Plant (PFP) are undergoing deactivation and decommissioning. RL and Fluor Hanford project managers at the PFP are committed to preserving historical artifacts of the plutonium production process. They

Influence of way of finishing furniture segments on amount emissions VOCs

Directory of Open Access Journals (Sweden)

Petr Čech

2010-01-01

Full Text Available The study deals with the influence of way of finishing furniture segments on amount emissions VOCs (volatile organic compounds. The so-called Volatile Organic Compounds (VOC are among the largest pollution sources of both the internal and external environments.VOC is defined as emission of any organic compound or a mixture thereof, with the exception of methane, whereby the compound exerts the pressure of 0.01 kPa or more at the temperature of 20 °C (293.15 K and reaches the corresponding volatility under the specific conditions of its use and can undergo photochemical reactions with nitrogen oxides when exposed to solar radiation. The effects of VOC upon environment can be described by equation: VOC + NOx + UV radiation + heat = tropospheric ozone (O3In this work there were tested MDF (medium density fibreboard coated by resin impregnated paper was used for the furniture components’ production. Next were tested compressed wood, which was used as a second material of furniture components. These both chosen materials was covered by resin impregnated paper and than sequentially finished by regular coat of finish.An attention of this study is especially put on mentioned factors and on quantity of instant and long-term VOCs emissions emitted from furniture components.The amount of emissions from furniture components, in different phases of the preparation including the resin impregnated paper coating finish, was monitored within the time intervals of 24 hours and 720 hours starting after the time of the finish preparation.The MDF (medium density fibreboard coated by resin impregnated paper was used for the furniture components´ production.A compressed wood was used as a second material of furniture components. This alternative material was covered by resin impregnated paper and than sequentially finished by regular coat of finish.

Effect of Hoodia gordonii leaf meal supplementation at finisher stage ...

African Journals Online (AJOL)

A nutritional experiment was conducted to determine the effect of Hoodia gordonii leaf meal supplementation at finisher stage (30 to 42 days old) on productivity, carcass characteristics and meat sensory attributes of Ross 308 broiler chickens. The chickens were fed a finisher diet supplemented with 0 (H0), 200 (H200), 300 ...

Comparison of gene expression and fatty acid profiles in concentrate and forage finished beef.

Science.gov (United States)

Buchanan, J W; Garmyn, A J; Hilton, G G; VanOverbeke, D L; Duan, Q; Beitz, D C; Mateescu, R G

2013-01-01

Fatty acid profiles and intramuscular expression of genes involved in fatty acid metabolism were characterized in concentrate- (CO) and forage- (FO) based finishing systems. Intramuscular samples from the adductor were taken at slaughter from 99 heifers finished on a CO diet and 58 heifers finished on a FO diet. Strip loins were obtained at fabrication to evaluate fatty acid profiles of LM muscle for all 157 heifers by using gas chromatography fatty acid methyl ester analysis. Composition was analyzed for differences by using the General Linear Model (GLM) procedure in SAS. Differences in fatty acid profile included a greater atherogenic index, greater percentage total MUFA, decreased omega-3 to omega-6 ratio, decreased percentage total PUFA, and decreased percentage omega-3 fatty acids in CO- compared with FO-finished heifers (P0.05). Upregulation was observed for PPARγ, fatty acid synthase (FASN), and fatty acid binding protein 4 (FABP4) in FO-finished compared with CO-finished heifers in both atherogenic index categories (P<0.05). Upregulation of diglyceride acyl transferase 2 (DGAT2) was observed in FO-finished heifers with a HAI (P<0.05). Expression of steroyl Co-A desaturase (SCD) was upregulated in CO-finished heifers with a LAI, and downregulated in FO-finished heifers with a HAI (P<0.05). Expression of adiponectin (ADIPOQ) was significantly downregulated in CO-finished heifers with a HAI compared with all other categories (P<0.05). The genes identified in this study which exhibit differential regulation in response to diet or in animals with extreme fatty acid profiles may provide genetic markers for selecting desirable fatty acid profiles in future selection programs.

Sequence finishing and mapping of Drosophila melanogasterheterochromatin

Energy Technology Data Exchange (ETDEWEB)

Hoskins, Roger A.; Carlson, Joseph W.; Kennedy, Cameron; Acevedo,David; Evans-Holm, Martha; Frise, Erwin; Wan, Kenneth H.; Park, Soo; Mendez-Lago, Maria; Rossi, Fabrizio; Villasante, Alfredo; Dimitri,Patrizio; Karpen, Gary H.; Celniker, Susan E.

2007-06-15

Genome sequences for most metazoans are incomplete due tothe presence of repeated DNA in the pericentromeric heterochromatin. Theheterochromatic regions of D. melanogaster contain 20 Mb of sequenceamenable to mapping, sequence assembly and finishing. Here we describethe generation of 15 Mb of finished or improved heterochromatic sequenceusing available clone resources and assembly and mapping methods. We alsoconstructed a BAC-based physical map that spans approximately 13 Mb ofthe pericentromeric heterochromatin, and a cytogenetic map that positionsapproximately 11 Mb of BAC contigs and sequence scaffolds in specificchromosomal locations. The integrated sequence assembly and maps greatlyimprove our understanding of the structure and composition of this poorlyunderstood fraction of a metazoan genome and provide a framework forfunctional analyses.

Explosion hazards of aluminum finishing operations

NARCIS (Netherlands)

Taveau, J.R.; Hochgreb, Simone; Lemkowitz, S.M.; Roekaerts, D.J.E.M.

2018-01-01

Metal dust deflagrations have become increasingly common in recent years. They are also more devastating than deflagrations involving organic materials, owing to metals' higher heat of combustion, rate of pressure rise, explosion pressure and flame temperature. Aluminum finishing operations offer

Explosion hazards of aluminum finishing operations

NARCIS (Netherlands)

Taveau, J.; Hochgreb, S.; Lemkowitz, S.M.; Roekaerts, D.J.E.M.

2018-01-01

Metal dust deflagrations have become increasingly common in recent years. They are also more devastating than deflagrations involving organic materials, owing to metals' higher heat of combustion, rate of pressure rise, explosion pressure and flame temperature. Aluminum finishing operations offer a

Surface roughness of microparticulated and nanoparticulated composites after finishing and polishing procedures

Directory of Open Access Journals (Sweden)

Rosemary Arai Sadami Shinkai

Full Text Available Objective: To evaluated the surface roughness of one microparticulate resin composite Durafill (Heraeus Kulzer Weihrheim, Germany andfour nanoparticulate resins 4 Seasons (Ivoclar Vivadent, Schaan, Liechtenstein Esthet x (Dentsply, Milford, DE, USA, Point 4 and Supreme (3M-ESPE, Dental Products,St. Paul, MN, USA. Methods: After finishing with a diamond bur point (F, and polishing with silicone points of gray, green and pink color Politipit (Ivoclar Vivadent,Schaan, Liechtenstein, four stages of completion were performed, simulating one of finishing and three of polishing a resin restoration. Ten samples of each composite resin were measured for surface roughness with surface profilometer (Mitutoyo Corporation, Tokyo, Japan after each of finishing and polishing sequence.Results: The results showed that nanoparticulate and microparticulate resins presented a significant difference in the surface roughness values, in all finishing and polishing steps. Conclusion: Of the the nanoparticulate resins 4 Seasons (Ivoclar Vivadent, Schaan, Liechtenstein, Point 4 (Kerr CO, Orange, CA, USA, and also microparticulate Durafill (Heraeus Kulzer Weihrheim, Germany presented significantly lower surface roughness values after completing all the finishing and polishing stages.

Polishing Metal Mirrors to 0,025 Micron Surface Finish

DEFF Research Database (Denmark)

Pedersen, P. E.

1978-01-01

A research program undertaken by the Danish Atomic Energy Commission required the fabrication of metal mirrors measuring 1 m long by 53 mm wide, which had to be finished to extremely tight tolerances on thickness, plane-parallelism and surface characteristics. Progressively finer diamond compound...... are employed to achieve a high gloss finish on the metal mirrors, which are used in polarized neutron experiments. This article describes the fabrication techniques developed at the Commission's Ris phi Central Workshop....

Tool steel quality and surface finishing of plastic molds

Directory of Open Access Journals (Sweden)

Rafael Agnelli Mesquita

2010-01-01

Full Text Available Plastic industry is today in a constant growth, demanding several products from other segments, which includes the plastic molds, mainly used in the injection molding process. Considering all the requirements of plastic molds, the surface finishing is of special interest, as the injected plastic part is able to reproduce any details (and also defects from the mold surface. Therefore, several aspects on mold finishing are important, mainly related to manufacturing conditions - machining, grinding, polishing and texturing, and also related to the tool steel quality, in relation to microstructure homogeneity and non-metallic inclusions (cleanliness. The present paper is then focused on this interrelationship between steel quality and manufacturing process, which are both related to the final quality of plastic mold surfaces. Examples are discussed in terms of surface finishing of plastic molds and the properties or the microstructure of mold steels.

On the improving of finishing works

International Nuclear Information System (INIS)

Arzamaskov, V.N.; Bondarenko, I.Ya.; Pogozhev, I.M.

1986-01-01

Problems of the improvement of finishing works performed during the construction of power installations are considered. Recommendations on the improvement of the quality of these works, increase of labour productivity and decrease of a manual labour share on their implementation are given

Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.

Science.gov (United States)

Black, R E; Hurley, F J; Havery, D C

2001-01-01

Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.

Design Process Control for Improved Surface Finish of Metal Additive Manufactured Parts of Complex Build Geometry

Directory of Open Access Journals (Sweden)

Mikdam Jamal

2017-12-01

Full Text Available Metal additive manufacturing (AM is increasingly used to create complex 3D components at near net shape. However, the surface finish (SF of the metal AM part is uneven, with surface roughness being variable over the facets of the design. Standard post-processing methods such as grinding and linishing often meet with major challenges in finishing parts of complex shape. This paper reports on research that demonstrated that mass finishing (MF processes are able to deliver high-quality surface finishes (Ra and Sa on AM-generated parts of a relatively complex geometry (both internal features and external facets under select conditions. Four processes were studied in this work: stream finishing, high-energy (HE centrifuge, drag finishing and disc finishing. Optimisation of the drag finishing process was then studied using a structured design of experiments (DOE. The effects of a range of finishing parameters were evaluated and optimal parameters and conditions were determined. The study established that the proposed method can be successfully applied in drag finishing to optimise the surface roughness in an industrial application and that it is an economical way of obtaining the maximum amount of information in a short period of time with a small number of tests. The study has also provided an important step in helping understand the requirements of MF to deliver AM-generated parts to a target quality finish and cycle time.

Design and Feasibility Testing of the truth FinishIt Tobacco Countermarketing Brand Equity Scale.

Science.gov (United States)

Evans, W Douglas; Rath, Jessica; Pitzer, Lindsay; Hair, Elizabeth C; Snider, Jeremy; Cantrell, Jennifer; Vallone, Donna

2016-07-01

The original truth campaign was a branded, national smoking prevention mass media effort focused on at-risk youth ages 12-17. Today the truth brand focuses on the goal of finishing tobacco (truth FinishIt). There have been significant changes in the tobacco control landscape, leading FinishIt to focus on 15- to 21-year-olds. The present article reports on formative research and media monitoring data collected to pilot test a new truth FinishIt brand equity scale. The goals of this study were to (a) content analyze truth FinishIt mass media ads, (b) assess truth's social media and followers' perceptions of truth's digital brand identity, and (c) develop and feasibility test a new version of the truth FinishIt brand equity scale using data from an existing Truth Initiative media monitoring study. Through factor analysis, we identified a brand equity scale, as in previous research, consisting of 4 main constructs: brand loyalty, leadership/satisfaction, personality, and awareness. Targeted truth attitudes and beliefs about social perceptions, acceptability, and industry-related beliefs were regressed on the higher order factor and each of the 4 individual brand equity factors. Ordinary least squares regression models generally showed associations in the expected directions (positive for anti-tobacco and negative for pro-tobacco) between targeted attitudes/beliefs and truth FinishIt brand equity. This study succeeded in developing and validating a new truth FinishIt brand equity scale. The scale may be a valuable metric for future campaign evaluation. Future studies should examine the effects of truth FinishIt brand equity on tobacco use behavioral outcomes over time.

Application of preliminary risk analysis at marble finishing plants in Recife's metropolitan area.

Science.gov (United States)

de Melo Neto, Rútilo P; Kohlman Rabbani, Emilia R

2012-01-01

The finishing of marble occurs in quarries all over Brazil, being the most significant dimension of the ornamental stone sector, with 7,000 businesses. Recife's Metropolitan Area (RMR) contains approximately 106 marble quarries, 25 of them unionized. The study focused on the application of Preliminary Risk Analysis, conducted at two unionized quarries: M1, a small business; and the second, M2, considered a micro enterprise. In this analysis both the administrative and the productive sectors were evaluated. The fieldwork was done in the month of December 2010. The study revealed that the two quarries carried moderate risks in the administrative sector, mainly due to ergonomic factors, and that in the productive sectors the risks were high, specifically because of excess noise, dust material, and precarious electrical installations. Using the results of the qualitative analysis as a base, the need for quantitative study presents itself in order to determine the most adequate modes of protection to be of assistance in the management of these risks, guaranteeing the safety and health of the worker and consequently the improvement in productivity in this sector.

FY 1989 report on the results of the development of the entrained bed coal gasification power plant. Part 2. Fabrication/installation of pilot plant; 1989 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 2. Pilot plant seisaku suetsuke hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

For the purpose of establishing the technology of the integrated coal gasification combined cycle power generation, the fabrication, installation work, etc. were conducted of a 200t/d entrained bed coal gasification pilot plant, and the FY 1989 results were summarized. As to the gasifier equipment, fabrication of a considerable number of the main equipment was finished. And, the equipment was sent into the coal gasification power plant and the installation work was done. Concerning gas refining facilities, fabrication of most of the components of the dry desulfurization system was finished, and further, fabrication of part of the piping prefabrication, disk and part of the disk fitting instrument was finished. The partial equipment of the dry dust removal system was also fabricated. About gas turbine facilities, the drawings necessary for each of the equipment fabricated/installed in this fiscal year were made, and at the same time a part of the technical data prepared so far was reviewed according to the progress of design. As to safety environmental facilities, installation work was done of gas treatment furnace, gas cooling system, buffer tank, desulfurizing tower, etc. Besides, design/technical study were made of the total control system, equipment of the indoor switching station, etc. (NEDO)

Study on waste waters of metal finishing industries around Lahore metropolitan area

International Nuclear Information System (INIS)

Khan, Izhar-ul-Haq; Mahmood, F.; Tufail, S.; Naeem, M.

2002-01-01

Study was undertaken on the waste water samples from metal finishing industries of Lahore metropolitan area for the evaluation of metallic impurities. The metal finishing industry was classified into three categories i. e. medium scale, small scale and cottage scale industry. About 93 wastewater samples were collected from various metal finishing industries around Lahore metropolitan area. In addition to toxic elements like cadmium, nickel and zinc the other parameters such as hydrogen ion concentration (pH), Electrical conductivity (EC) and Total Dissolved Salts (TDS) were also determined. (author)

DEVELOPING A CAPE-OPEN COMPLIANT METAL FINISHING FACILITY POLLUTION PREVENTION TOOL (CO-MFFP2T)

Science.gov (United States)

The USEPA is developing a Computer Aided Process Engineering (CAPE) software tool for the metal finishing industry that helps users design efficient metal finishing processes that are less polluting to the environment. Metal finishing process lines can be simulated and evaluated...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... cattle-like hides into finished leather by hair save unhairing, chrome tanning, and retan-wet finishing. ...

40 CFR 425.90 - Applicability; description of the retan-wet finish-splits subcategory.

Science.gov (United States)

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously unhaired and tanned splits into finished leather by...

76 FR 79221 - Penske Logistics, LLC, Customer Service Department General Motors and Tier Finished Goods...

Science.gov (United States)

2011-12-21

..., Customer Service Department General Motors and Tier Finished Goods/Finished Goods Division; a Subsidiary of... Manpower El Paso, TX; Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance... should read Penske Logistics, LLC, Customer Service Department, General Motors and Tier Finished Goods...

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Science.gov (United States)

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously tanned hides and skins (grain side only) into finished...

Surface-finish effects on the high-cycle fatigue of Alloy 718

International Nuclear Information System (INIS)

Korth, G.E.

1981-06-01

Alloy 718 us a precipitation-hardening nickel-base superalloy that is being specified for various components for liquid-meal fast breeder reactors (LMFBRs). This alloy maintains high strength at elevated temperatures making it a desirable structural material. But the property that justifies most LMFBR applications is the alloy's resistance to thermal striping damage due to its high fatigue endurance strength. Thermal striping is a high-cycle fatigue phenomenon caused by thermal stresses from the fluctuating mixing action of sodium streams of differing temperatures impinging on the metal surfaces. Most of the design data is generated from laboratory fatigue specimens with carefully controlled surface finishes prepared with a low-stress grind and buffed to a surface finish 8--12 in. Since Alloy 718 has been shown to be quite notch sensitive under cyclic loading, the detrimental effect on the high-cycle fatigue properties caused by shop surface finishes of actual components has been questioned. This report examines some of the surface finishes that could be produced in a commercial shop on an actual component

Investigation of Floor Surface Finishes for Optimal Slip Resistance Performance

Directory of Open Access Journals (Sweden)

In-Ju Kim

2018-03-01

Full Text Available Background: Increasing the slip resistance of floor surfaces would be desirable, but there is a lack of evidence on whether traction properties are linearly correlated with the topographic features of the floor surfaces or what scales of surface roughness are required to effectively control the slipperiness of floors. Objective: This study expands on earlier findings on the effects of floor surface finishes against slip resistance performance and determines the operative ranges of floor surface roughness for optimal slip resistance controls under different risk levels of walking environments. Methods: Dynamic friction tests were conducted among three shoes and nine floor specimens under wet and oily environments and compared with a soapy environment. Results: The test results showed the significant effects of floor surface roughness on slip resistance performance against all the lubricated environments. Compared with the floor-type effect, the shoe-type effect on slip resistance performance was insignificant against the highly polluted environments. The study outcomes also indicated that the oily environment required rougher surface finishes than the wet and soapy ones in their lower boundary ranges of floor surface roughness. Conclusion: The results of this study with previous findings confirm that floor surface finishes require different levels of surface coarseness for different types of environmental conditions to effectively manage slippery walking environments. Collected data on operative ranges of floor surface roughness seem to be a valuable tool to develop practical design information and standards for floor surface finishes to efficiently prevent pedestrian fall incidents. Keywords: floor surface finishes, operational levels of floor surface roughness, slip resistance, wet, soapy and oily environments

Cross-Cultural Consumer Acceptability and Purchase Intent of Forage-Finished Rib-Eye Steaks.

Science.gov (United States)

Torrico, Damir Dennis; Wardy, Wisdom; Pujols, Kairy Dharali; Carabante, Kennet Mariano; Jirangrat, Wannita; Scaglia, Guillermo; Janes, Marlene E; Prinyawiwatkul, Witoon

2015-10-01

Rib-eye steaks, from 3 forage-finished systems (S1, S2, and S3) and 1 commercial steak (C), either cooked by 1-sided-grilling or 2-sided-grilling, were evaluated for sensory acceptability [overall appearance (ORA) and overall appearance of fat (OAF) for raw steaks; overall appearance (OCA), overall beef aroma (OBA), overall beef flavor (OBF), juiciness, tenderness and overall liking (OL) for cooked steaks] and purchase intent by Hispanic, Asian and U.S. consumers. They also indicated preferred degree of doneness and cooking methods. Cross-cultural differences in preferences and consumer acceptability of rib-eye steaks were observed. Grilling was the most preferred cooking method. Hispanics and Asians preferred medium and/or medium well, while U.S. consumers preferred medium and/or medium rare. For cooked steaks, the population effect was significant for all sensory attributes; Asians generally scored lower than did Hispanics and U.S. consumers. C and S3 generally had higher scores for all sensory attributes across 3 populations. Purchase intent for all forage-finished steaks was higher for Hispanics and U.S. consumers compared to Asians (50.0% to 77.8% compared with 43.2% to 65.9%). Attributes influencing purchase intent of forage-finished steaks differed among populations: tenderness (odds ratio = 1.4) for Hispanics, OCA (odds ratio = 1.5) for Asians, and OBF (odds ratio = 1.3) for U.S. consumers. Overall, this study demonstrated that the type of forage-finished system and ethnic differences influenced sensory acceptability and purchase intent of forage-finished rib-eye steaks. Demand for forage-finished beef has increased worldwide due to its potential health benefits. Little is known regarding the cross-cultural effects on the consumer acceptance of forage-finished beef. We evaluated sensory acceptance and purchase intent of raw and cooked forage-finished rib-eye steaks using Hispanic, Asian, and U.S. (White and African American) populations. This study

DEVELOPMENT OF THE U.S. EPA'S METAL FINISHING FACILITY POLLUTION PREVENTION TOOL

Science.gov (United States)

Metal finishing processes are a type of chemical processes and can be modeled using Computer Aided Process Engineering (CAPE). Currently, the U.S. EPA is developing the Metal Finishing Facility Pollution Prevention Tool (MFFP2T), a pollution prevention software tool for the meta...

Analysis of Failure to Finish a Race in a Cohort of Thoroughbred Racehorses in New Zealand

Directory of Open Access Journals (Sweden)

Jasmine Tanner

2016-05-01

Full Text Available The objective was to describe the incidence of failure to finish a race in flat-racing Thoroughbreds in New Zealand as these are summary indicators of falls, injuries and poor performance. Retrospective data on six complete flat racing seasons (n = 188,615 race starts of all Thoroughbred flat race starts from 1 August 2005 to 31 July 2011 were obtained. The incidence of failure to finish events and binomial exact 95% confidence intervals were calculated per 1000 horse starts. The association between horse-, rider- and race-level variables with the outcomes failure to finish, pulled-up/fell and lost rider were examined with a mixed effects Poisson regression model. A total of 544 horses failed to finish in 188,615 race starts with an overall incidence of 2.88 per 1000 horse starts (95% CI 2.64–3.12. The incidence of failure to finish horses across each race year showed little variability. In the univariable analysis race distance, larger field size, season, and ratings bands showed association with failing to finish a race. The overall failure to finish outcome was associated with season, race distance and ratings bands (horse experience and success ranking criteria. In the multivariable analysis, race distance and ratings bands were associated with horses that pulled-up/fell; season, apprentice allowances and ratings bands were associated with the outcome lost rider. The failure to finish rate was lower than international figures for race day catastrophic injury. Racing and environmental variables were associated with failure to finish a race highlighting the multifactorial nature of race-day events. Further investigation of risk factors for failure to finish is required to better understand the reasons for a low failure to finish rate in Thoroughbred flat races in New Zealand.

The importance of surface finish to energy performance

Directory of Open Access Journals (Sweden)

Smith Geoff B.

2017-01-01

Full Text Available Power generation in solar energy systems, thermal control in buildings and mitigation of the Urban Heat Island problem, are all sensitive to directional response to incoming radiation. The radiation absorption and emission profile also plays a crucial role in each system's response and depends strongly on surface finish. This important sensitivity needs wider recognition in materials data sheets, system modeling, plus in materials and environmental engineering. The impact of surface roughness on thermal response of natural and man-made external environments is examined. Important examples will be given of the role of surface finish within each class. Total emittance links to the way surface finish influences directional emittance E(θ. Smooth surface thermal emittance on PV module covers, many solar absorbers, some roof paints, polished concrete, and glass windows can be up to 15% different from insulator results based on fully diffuse models of the same material. Widespread evidence indicates smooth metals and low-E solar absorber surfaces cool faster, and smooth insulators slower than previously thought. Matt paint is cooler than low sheen paint under the same solar heating impacts and normal concrete cooler than polished. Emittance for water is the prime environmental example of oblique impacts as it reflects strongly at oblique incidence, which leads to a significant drop in E(θ. Ripples or waves however raise water's average emittance. A surprise in this work was the high sensitivity of total E and its angular components to roughness in the depth range of 0.1–0.8 μm, which are well under ambient thermal IR wavelengths of 3–30 μm but common in metal finishing. Parallel energy flows such as evaporation and convective cooling vary if emittance varies. Thermal image analysis can provide insights into angular radiative effects.

Proceedings of national executive management seminar on surface finishing by radiation curing technology: radiation curing for better finishing

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

This book compiled the paper presented at this seminar. The papers discussed are 1. Incentives for investment in the manufacturing sector (in Malaysia) 2.Trends and prospect of surface finishing by radiation curing technology in Malaysia 3. Industrial application of radiation curing.

Proceedings of national executive management seminar on surface finishing by radiation curing technology: radiation curing for better finishing

International Nuclear Information System (INIS)

1993-01-01

This book compiled the paper presented at this seminar. The papers discussed are 1. Incentives for investment in the manufacturing sector (in Malaysia) 2.Trends and prospect of surface finishing by radiation curing technology in Malaysia 3. Industrial application of radiation curing

Processing and finishing of granite surfaces

OpenAIRE

Klich, J. (Jiří); Hlaváček, P. (Petr); Ščučka, J. (Jiří); Sitek, L. (Libor); Foldyna, J. (Josef); Georgiovská, L. (Lucie); Souček, K. (Kamil); Staš, L. (Lubomír); Bortolussi, A.

2013-01-01

The article deals with granite surface processing and finishing by various methods including bush hammering, flaming, polishing, continuous and pulsating water jetting. Both optical and CT X-ray methods are used for analysis of surface and subsurface areas of tested samples. Advantages of pulsating water jetting compared to other techniques are discussed.

Effects of the truth FinishIt brand on tobacco outcomes

OpenAIRE

Evans, W. Douglas; Rath, Jessica M.; Hair, Elizabeth C.; Snider, Jeremy Williams; Pitzer, Lindsay; Greenberg, Marisa; Xiao, Haijun; Cantrell, Jennifer; Vallone, Donna

2017-01-01

Since 2000, the truth campaign has grown as a social marketing brand. Back then, truth employed branding to compete directly with the tobacco industry. In 2014, the launch of truth FinishIt reflected changes in the brand's strategy, the tobacco control environment, and youth/young adult behavior.Building on a previous validation study, the current study examined brand equity in truth FinishIt, as measured by validated multi-dimensional scales, and tobacco related attitudes, beliefs, and behav...

Ageing of Dry Cement Mixes for Finishing Purposes

Directory of Open Access Journals (Sweden)

Bronius VEKTARIS

2013-09-01

Full Text Available Dry building mixes, stored in the air, absorb water vapor and CO2 gas and ageing because properties of binding materials, mostly Portland cement, deteriorate after its prehydration and carbonation. In this paper the ageing singularities of dry cement mixes for finishing purposes and additives for retarding this process has been determinated. Ordinary and quickly hardening Portland cements absorb H2O and CO2 more than white cement – about 70 % – 75 % and 30 % – 38 % per month of innitial mass, respectively. White cement is more resistant to prehydration and carbonation, because it contains less C3A, C4AF and alkali, characterized initial activity. Dry mixes with white cement, although slower, but still worse after stored. Influence of routine dry mortar mixes ingredients and additives (methyl cellulose, pigments, sand and lime on prehydration properties of the mixes for finishing purpose is not substantial. Significant positive influence comes from the addition of fatty acid salts (zinc stearate or sodium oleate. The dry cement mixes for finishing purpose has been recomended to hydrophobisate with one of these additives, adding about 1 % by weight of cement during preducing mixes. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.5243

Ageing of Dry Cement Mixes for Finishing Purposes

Directory of Open Access Journals (Sweden)

Bronius VEKTARIS

2013-09-01

Full Text Available Dry building mixes, stored in the air, absorb water vapor and CO2 gas and ageing because properties of binding materials, mostly Portland cement, deteriorate after its prehydration and carbonation. In this paper the ageing singularities of dry cement mixes for finishing purposes and additives for retarding this process has been determinated. Ordinary and quickly hardening Portland cements absorb H2O and CO2 more than white cement – about 70 % – 75 % and 30 % – 38 % per month of innitial mass, respectively. White cement is more resistant to prehydration and carbonation, because it contains less C3A, C4AF and alkali, characterized initial activity. Dry mixes with white cement, although slower, but still worse after stored. Influence of routine dry mortar mixes ingredients and additives (methyl cellulose, pigments, sand and lime on prehydration properties of the mixes for finishing purpose is not substantial. Significant positive influence comes from the addition of fatty acid salts (zinc stearate or sodium oleate. The dry cement mixes for finishing purpose has been recomended to hydrophobisate with one of these additives, adding about 1 % by weight of cement during preducing mixes. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.5243

Improvements in Sand Mold/Core Technology: Effects on Casting Finish

Energy Technology Data Exchange (ETDEWEB)

Prof. John J. Lannutti; Prof. Carroll E. Mobley

2005-08-30

In this study, the development and impact of density gradients on metal castings were investigated using sand molds/cores from both industry and from in-house production. In spite of the size of the castings market, almost no quantitative information about density variation within the molds/cores themselves is available. In particular, a predictive understanding of how structure and binder content/chemistry/mixing contribute to the final surface finish of these products does not exist. In this program we attempted to bridge this gap by working directly with domestic companies in examining the issues of surface finish and thermal reclamation costs resulting from the use of sand molds/cores. We show that these can be substantially reduced by the development of an in-depth understanding of density variations that correlate to surface finish. Our experimental tools and our experience with them made us uniquely qualified to achieve technical progress.

The Adolescent Who Does Not Finish Anything.

Science.gov (United States)

Breiner, Sander J.

1985-01-01

Practical information for therapists who deal with adolescents who do not finish tasks is presented. The relationship of task incompletion to neurosis, psychosis, depression, homosexuality, and drug abuse is described, and techniques and guidelines for treatment are provided. (Author)

Possibilities of the metallurgical base in the manufacture of tubes for nuclear power plant steam generators

International Nuclear Information System (INIS)

Prnka, T.; Walder, V.; Dolenek, J.

Current possibilities are briefly summarized of metallurgy in the manufacture of high-quality tubes for nuclear power plant steam generators, mainly for fast reactor power plants. Discussed are steel making possibilities, semi-finished product and tube forming with special regard to 2.25Cr1MoNiNb steel problems, heat treatment, finishing, and testing. Necessary equipment and technology for the production of steam generator tubes are less common in the existing practice and are demanding on investment; their introduction, however, is inevitable for securing quality production of steam generator tubes. (Kr)

Effects of finishing/polishing techniques on microleakage of resin-modified glass ilonomer cement restorations.

Science.gov (United States)

Yap, Adrian U J; Yap, W Y; Yeo, Egwin J C; Tan, Jane W S; Ong, Debbie S B

2003-01-01

This study investigated the effect of finishing/polishing techniques on the microleakage of resin-modified glass ionomer restorations. Class V preparations were made on the buccal and lingual/palatal surfaces of freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (FT [GC]) and Photac-Fil Quick (PF [3M-ESPE]) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with eight-fluted tungsten carbide burs. The teeth were then randomly divided into four groups and finishing/polishing was done with one of the following systems: (a) Robot Carbides (RC); (b) Super-Snap system (SS); (c) OneGloss (OG) and (d) CompoSite Polishers (CS). The sample size for each material-finishing/polishing system combination was eight. After finishing/polishing, the teeth were stored in distilled water at 37 degrees C for one week. The root apices were then sealed with acrylic and two coats of varnish was applied 1 mm beyond the restoration margins. The teeth were subsequently subjected to dye penetration testing (0.5% basic fuchsin), sectioned and scored. Data was analyzed using Kruskal-Wallis and Mann-Whitney U tests at a significance level of 0.05. Results of statistical analysis were as follows: Enamel margins: PF-OGfinishing/polishing technique, leakage at dentin margins was significantly greater than at enamel margins for FT. For PF, no significant difference in leakage scores was observed between dentin and enamel with the exception of finishing/polishing with OG. FT restorations had significantly less enamel and dentin leakage than PF restorations when treated with OG. The effect of finishing/polishing techniques on microleakage was both tissue and material dependent.

SEM Evaluation of Surrounding Enamel after Finishing of Composite Restorations- Preliminary Results

Science.gov (United States)

Iovan, G.; Stoleriu, S.; Solomon, S.; Ghiorghe, A.; Sandu, A. V.; Andrian, S.

2017-06-01

The purpose of this study was to analyze the surface characteristics of the enamel adjacent to composite resin after finishing the restoration with different diamond and tungsten carbide burs. The topography of enamel was observed by using a scanning electron microscope. Finishing with extra-/ultra-fine carbide burs, and extra-fine diamond burs resulted in smooth surfaces. In few areas some superficial scratches with no clinical relevance were observed. Deep grooves were observed on the surface of enamel when fine diamond burs were used. Finishing of composite restorations with coarse burs should be avoided when there is a high risk of touching and scratching adjacent enamel during the procedure.

THE CONCEPTUAL APPARATUS OF THE TERM "FINISHED GOODS" AS AN OBJECT OF ACCOUNTING

Directory of Open Access Journals (Sweden)

A. Kasich

2016-11-01

Full Text Available The article studies scientific approaches to the definition of "finished goods"; properties and various characteristics of the finished goods, which, in the author’s opinion, affect to the term’s wording. identified generalized features of the concept and differences from the executed works and the rendered services. Described the features and the main differences the ways of production of finished goods in certain economy’s sectors and proved the necessity of taking into account the specific features during the approach to the concept of "finished goods" in various industries. Analyzed the common and distinctive features of international and national standards for the accounting of inventory, because in the conditions of globalization becomes important the necessity of their identity. investigated the components of enterprise accounting policies, such as evaluation of reserves and write-offs on trade, applied in different countries of the world, revealed a basic discrepancy, namely, the use of LiFO method, which is prohibited for use in Ukraine, which, however, is used almost in all the considered countries. On the basis of the conducted research the author’s definition of "finished goods".

Algorithm of actions to identify and reduce risks in the production of milk and plant products

Directory of Open Access Journals (Sweden)

L. E. Glagoleva

2016-01-01

Full Text Available Foods with a new generation of functional and improved consumer properties, corresponds to the modern concepts of nutrition science and consumer needs. functional food production is a major global trend in food science and the subject of innovation. One of the important trends is the use of plant complexes and plant food systems. Using the plant complexes (PC and plant food systems (PFS provides a number of benefits: improved consumer properties of the product, do not need to change the process, it is possible to control directional rheological properties and consistency of the finished products, reduced the number of risk points in the production cycle. This paper describes the development of an algorithm of action to identify and mitigate risks in the production of milk and plant products. Also conducted a risk analysis, identified and assessed the risks in the process of production, installed capacity of available resources to reduce the level of risk. Established and submitted to the critical control points in production processes, as well as the critical limits for each critical control points, and the procedure for corrective action in case of violations of the past. During the study, measured changes in the quantitative and qualitative composition of microflora of semi-finished and Quantity of Mesophilic Aerobic and Facultative Anaerobic Microorganisms (QMAFAnM. To determine QMAFAnM samples were taken: 1 – cheesecakes (control, 2 – cheesecakes with RPS. Microbiological studies analyzed frozen-conjugated semi-finished products was determined within 90 days. It is clear from the data that the cottage cheese with semi-finished products have a lower RPM 11.7%. Analyzing the data, it is possible to conclude that the physico-chemical, organoleptic and microbiological indicators of products was developed to set standards on cheese semi-finished products. multilevel structure that characterizes the quality indicators has been developed and is

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... addition to other unhairing and tanning operation, processes raw or cured cattle or cattle-like hides into finished leather by chemically dissolving the hide hair, chrome tanning, and retan-wet finishing. ...

77 FR 12227 - Long Term 2 Enhanced Surface Water Treatment Rule: Uncovered Finished Water Reservoirs; Public...

Science.gov (United States)

2012-02-29

... Water Treatment Rule: Uncovered Finished Water Reservoirs; Public Meeting AGENCY: Environmental... review of the uncovered finished water reservoir requirement in the Long Term 2 Enhanced Surface Water... uncovered finished water reservoir requirement and the agency's Six Year Review process. EPA also plans to...

Pneumonia outbreaks in calves and finishers.

Science.gov (United States)

2016-03-19

Pneumonia in calves and finishers. Ovarian tumour in a calf . Abortion associated with bovine herpesvirus 1 in a suckler herd. Parasitic gastroenteritis causing illthrift and death in sheep. Outbreaks of acute fasciolosis in sheep. These are among matters discussed in the disease surveillance report for December 2015 from SAC Consulting: Veterinary Services (SAC C VS). British Veterinary Association.

Performance, profitability and greenhouse gas emissions of alternative finishing strategies for Holstein-Friesian bulls and steers.

Science.gov (United States)

Murphy, B; Crosson, P; Kelly, A K; Prendiville, R

2018-02-06

Modifying finishing strategies within established production systems has the potential to increase beef output and farm profit while reducing greenhouse gas (GHG) emissions. Thus, the objectives of this study were to investigate the effects of finishing duration on animal performance of Holstein-Friesian (HF) bulls and steers and evaluate the profitability and GHG emissions of these finishing strategies. A total of 90 HF calves were assigned to a complete randomised block design; three bull and three steer finishing strategies. Calves were rotationally grazed in a paddock system for the first season at pasture, housed and offered grass silage ad libitum plus 1.5 kg DM of concentrate per head daily for the first winter and returned to pasture for a second season. Bulls were slaughtered at 19 months of age and either finished indoors on concentrates ad libitum for 100 days (19AL), finished at pasture supplemented with 5 kg DM of concentrate per head daily for 100 (19SP) or 150 days (19LP). Steers were slaughtered at 21 months of age and finished at pasture, supplemented with 5 kg DM of concentrate per head daily for 60 (21SP) and 110 days (21LP) or slaughtered at 24 months of age and finished indoors over the second winter on grass silage ad libitum plus 5 kg DM of concentrate per head daily (24MO). The Grange Dairy Beef Systems Model and the Beef Systems Greenhouse Gas Emissions Model were used to evaluate profitability and GHG emissions, respectively. Average daily gain during the finishing period (Pprofit.

Experience in the construction of a spent nuclear fuel reprocessing plant

International Nuclear Information System (INIS)

Yamashita, Hiroshi

1976-01-01

The construction and operation of a reprocessing plant was first published in 1956. The Reprocessing Expert Committee of AEC was established in 1959, and the preliminary design was finished in 1964 by NCP of Britain. The detailed design was completed in 1969 by SGN of France, and the training of operators was carried out in parallel with this in France. The results of the safety investigation was approved in Jan. 1970, and the construction was started in June 1971. The site of the reprocessing plant is the eastern part of the Tokai Establishment of PNC. The process adopted is the wet Purex process having been established in large practical plants. The treating capacity is 0.7 t/day. The main processes are acceptance and storage, mechanical treatment, and chemical treatment. The reprocessing facilities comprise the main shop, the analysis station, the main exhaust stack, the decontamination station, the solid waste store, the sea discharge pipe, and other incidental facilities. The construction works were about 7 months behind the schedule when the water flow test was finished. The chemical test was finished in March, 1975, and the uranium test is in progress since Sept., 1975. The problems for future are the developments of effective waste treatment and storing techniques, and the researches have been carried out by PNC. The construction project of the second plant is urgently required, since it takes 10 years from planning to operation. (Kako, I.)

Drivers of Finished-Goods Inventory in the U.S. Automobile Industry

OpenAIRE

Gérard P. Cachon; Marcelo Olivares

2010-01-01

Automobile manufacturers in the U.S. supply chain exhibit significant differences in their days of supply of finished vehicles (average inventory divided by average daily sales rate). For example, from 1995 to 2004, Toyota consistently carried approximately 30 fewer days of supply than General Motors. This suggests that Toyota's well-documented advantage in manufacturing efficiency, product design, and upstream supply chain management extends to their finished-goods inventory in their downstr...

Analytical methods for the characterization of surface finishing in bricks

International Nuclear Information System (INIS)

Nardini, I.; Zendri, E.; Biscontin, G.; Brunetin, A.

2006-01-01

The recent restoration works of Santo Stefano Church Facade (XV century) in Venice have shown traces variously saved of different kind of surface finishes. These finishes were found on the brick's surface both in the masonry and in the decorative elements. Different brick's surface and decorative tile samples were investigated using several techniques: optical microscopy, scanning electron-microscopy, thermal analysis, infrared spectroscopy and reflectance Fourier transform infrared microspectroscopy. The evaluation of the reached results was used to understand the decorative techniques and to recognize the material employed

Implementing Cleaner Printed Wiring Board Technologies: Surface Finishes

Science.gov (United States)

This document describes the problems, solutions, and time and effort involved in implementing alternative surface finish technologies, and this guide is produced as part of the DfE Printed Wiring Board Project

Surface Finish Effects Using Coating Method on 3D Printing (FDM) Parts

Science.gov (United States)

Haidiezul, AHM; Aiman, AF; Bakar, B.

2018-03-01

One of three-dimensional (3-D) printing economical processes is by using Fused Deposition Modelling (FDM). The 3-D printed object was built using layer-by-layer approach which caused “stair stepping” effects. This situation leads to uneven surface finish which mostly affect the objects appearance for product designers in presenting their models or prototypes. The objective of this paper is to examine the surface finish effects from the application of XTC-3D coating developed by Smooth-On, USA on the 3D printed parts. From the experimental works, this study shows the application of XTC-3D coating to the 3-D printed parts has improve the surface finish by reducing the gap between the layer

DESIGN OF FILL AND FINISH FACILITY FOR ACTIVE PHARMACEUTICAL INGREDIENTS (API)

OpenAIRE

NUUR LAILA KHAIRUDDIN; NORLIZA ABD. RAHMAN; NUR SYAFIQAH KAMARUDIN

2016-01-01

Fill and finish operations continue to be one of the most heavily outsourced activities in the biopharmaceutical manufacturing market today. There are a few aspects that need to be consider in outsource activities like logistic, storage condition, facility certification and audit as regulations and standards which the manufacturer should adhere. Risk would be greater and extra care should be taken when outsource from foreign fill and finish facility. Thus, the internal aseptic fill and fin...

Characterisation of the joining zone of serially arranged hybrid semi-finished components

Science.gov (United States)

Behrens, B.-A.; Chugreev, A.; Matthias, T.

2018-05-01

Forming of already joined semi-finished products is an innovative approach to manufacture components which are well-adapted to external loads. This approach results in an economically and ecologically improved production by the targeted use of high-quality materials in component areas, which undergo high stresses. One possible production method for hybrid semi-finished products is friction welding. This welding method allows for the production of hybrid semi-finished products made of aluminium and steel as well as steel and steel. In this paper, the thermomechanical tensile and shear stresses causing a failure of the joined zone are experimentally determined through tension tests. These tests are performed with specimens whose joint zones are aligned with different angles to the load direction.

Productive performance of Holstein calves finished in feedlot or pasture

Directory of Open Access Journals (Sweden)

ANA MARIA O. DIAS

Full Text Available ABSTRACT The use of animals from dairy farms is an alternative to meat production since it provides an increment of total income for farmers. This study aims to evaluate the performance of Holstein calves finished in two feeding systems (feedlot or pasture. Forty-three animals with 58 days old and 57 kg were divided in two treatments: 23 animals finished in feedlot with corn silage plus concentrate based on corn and soybean meal (40:60; 20 animals kept in cultivated pastures according to the period of the year: Italian ryegrass (Lolium multiflorum and pearl millet (Pennisetum americanum with supplementation with the same feedlot-concentrate at 1% body weight. Animals were slaughtered with 200 kg. Dry matter and nutrient intake were determined, with the use of chromium oxide for estimating pasture intake. Feedlot animals had greater total intake and total digestible nutrients, resulting in higher average daily gain (0.949 vs 0.694 kg day-1. Crude protein intake, neutral detergent fiber and feed conversion did not show significant differences. Holstein calves have improved performance when finished in feedlot.

Finishing of additively manufactured titanium alloy by shape adaptive grinding (SAG)

Science.gov (United States)

Beaucamp, Anthony T.; Namba, Yoshiharu; Charlton, Phillip; Jain, Samyak; Graziano, Arthur A.

2015-06-01

In recent years, rapid prototyping of titanium alloy components for medical and aeronautics application has become viable thanks to advances in technologies such as electron beam melting (EBM) and selective laser sintering (SLS). However, for many applications the high surface roughness generated by additive manufacturing techniques demands a post-finishing operation to improve the surface quality prior to usage. In this paper, the novel shape adaptive grinding process has been applied to finishing titanium alloy (Ti6Al4V) additively manufactured by EBM and SLS. It is shown that the micro-structured surface layer resulting from the melting process can be removed, and the surface can then be smoothed down to less than 10 nm Ra (starting from 4-5 μm Ra) using only three different diamond grit sizes. This paper also demonstrates application of the technology to freeform shapes, and documents the dimensional accuracy of finished artifacts.

Flame retardant finishing of cotton fabric based on synergistic compounds containing boron and nitrogen.

Science.gov (United States)

Xie, Kongliang; Gao, Aiqin; Zhang, Yongsheng

2013-10-15

Boric acid and compound containing nitrogen, 2,4,6-tri[(2-hydroxy-3-trimethyl-ammonium)propyl]-1,3,5-triazine chloride (Tri-HTAC) were used to finish cotton fabric. The flame retardant properties of the finished cotton fabrics and the synergetic effects of boron and nitrogen elements were investigated and evaluated by limited oxygen index (LOI) method. The mechanism of cross-linking reaction among cotton fiber, Tri-HTAC, and boric acid was discussed by FTIR and element analysis. The thermal stability and surface morphology of the finished cotton fabrics were investigated by thermogravimetric analysis (TGA) and scanning electron microscope (SEM), respectively. The finishing system of the mixture containing boron and nitrogen showed excellent synergistic flame retardancy for cotton fabric. The cotton fabric finished with mixture system had excellent flame retardancy. The LOI value of the treated cotton fabric increased over 27.5. Tri-HTAC could form covalent bonds with cellulose fiber and boric acid. The flame retardant cotton fabric showed a slight decrease in tensile strength and whiteness. The surface morphology of flame retardant cotton fiber was smooth. Copyright © 2013 Elsevier Ltd. All rights reserved.

A European longitudinal study in Salmonella seronegative and seropositive-classified finishing pig herds

DEFF Research Database (Denmark)

Wong, Danilo Lo Fo; Dahl, J.; Wingstrand, Anne

2004-01-01

and was performed between October 1996 and May 1999. The Salmonella status of finishing pig herds was determined by an initial blood sampling of approximately 50 finishing pigs close to market weight per herd. The development of the Salmonella status of the selected herds was assessed at seven subsequent sampling...

Portable flooring protects finished surfaces, is easily moved

Science.gov (United States)

Carmody, R. J.

1964-01-01

To protect curved, finished surface and provide support for workmen, portable flooring has been made from rigid plastic foam blocks, faced with aluminum strips. Held together by nylon webbing, the flooring can be rolled up for easy carrying.

Effects of delayed finishing/polishing on surface roughness, hardness and gloss of tooth-coloured restorative materials.

Science.gov (United States)

Yazici, A Ruya; Tuncer, Duygu; Antonson, Sibel; Onen, Alev; Kilinc, Evren

2010-01-01

The aim of this study was to investigate the effect of delayed finishing/polishing on the surface roughness, hardness and gloss of tooth-coloured restorative materials. Four different tooth-coloured restoratives: a flowable resin composite- Tetric Flow, a hybrid resin composite- Venus, a nanohybrid resin composite- Grandio, and a polyacid modified resin composite- Dyract Extra were used. 30 specimens were made for each material and randomly assigned into three groups. The first group was finished/polished immediately and the second group was finished/polished after 24 hours. The remaining 10 specimens served as control. The surface roughness of each sample was recorded using a laser profilometer. Gloss measurements were performed using a small-area glossmeter. Vickers microhardness measurements were performed from three locations on each specimen surface under 100g load and 10s dwell time. Data for surface roughness and hardness were analyzed by Kruskal Wallis test and data for gloss were subjected to one-way ANOVA and Tukey test (P gloss values were recorded under Mylar strip for all materials. While delayed finishing/polishing resulted in a significantly higher gloss compared to immediate finishing/polishing in Venus samples (P .05). The lowest hardness values were found under Mylar strip. Delayed finishing/polishing significantly increased the hardness of all materials. The effect of delayed finishing/polishing on surface roughness, gloss and hardness appears to be material dependent.

New trends for PWB surface finishes in mobile phone applications

DEFF Research Database (Denmark)

Nielsen, Claus Würtz; Ambat, Rajan; Rasmussen, Anette Alsted

2005-01-01

Immersion Ni/Au has been the overall dominant surface finish on PWB's for the last 10 years. During the last 5 years Mobile Phones have been extremely popular and spread all over the world in different climate zones in very high volumes. At the same time the Mobile Phone terminal for many people...... use of Imm. Ni/Au unnecessary in the near future. The end result is higher reliability with less expensive and simpler processes. This paper will discuss the various considerations for choice of surface finish and results from the extensive feasibility studies performed by Nokia Mobile Phones...

Persistence of antimicrobial resistance genes from sows to finisher pigs

DEFF Research Database (Denmark)

Birkegård, Anna Camilla; Halasa, Tariq; Folkesson, Anders

2018-01-01

Antimicrobial resistance in pigs has been under scrutiny for many years. However, many questions remain unanswered, including whether the initial antimicrobial resistance level of a pig will influence the antimicrobial resistance found at slaughter. Faecal samples from finishers pigs from 681 farms...... and from sows from 82 farms were collected, and levels of seven antimicrobial resistance genes, ermB, ermF, sulI, sulII, tet(M), tet(O), and tet(W), were quantified by high-capacity qPCR. There were 40 pairs of observations where the finishers were born in the farms of the sows. The objective of this study...

Control software development for magnetorheological finishing of large aperture optical elements

International Nuclear Information System (INIS)

Zheng Nan; Li Haibo; Yuan Zhigang; Zhong Bo

2011-01-01

Based on the mechanism of magnetorheological finishing, the dwell time function was solved by Jansson-Van Cit-tert algorithm to accomplish the kernel module design. Then the software modularization programming, modular testing and integration testing were conducted. A verification experiment was carried out on a crystal element with full aperture of 500 mm and the element's surface achieved rapid and efficient convergence after the software controlled magnetorheological finishing. It is proved that the software could control the whole polishing process accurately. (authors)

Finishing of additively manufactured titanium alloy by shape adaptive grinding (SAG)

International Nuclear Information System (INIS)

Beaucamp, Anthony T; Namba, Yoshiharu; Charlton, Phillip; Jain, Samyak; Graziano, Arthur A

2015-01-01

In recent years, rapid prototyping of titanium alloy components for medical and aeronautics application has become viable thanks to advances in technologies such as electron beam melting (EBM) and selective laser sintering (SLS). However, for many applications the high surface roughness generated by additive manufacturing techniques demands a post-finishing operation to improve the surface quality prior to usage. In this paper, the novel shape adaptive grinding process has been applied to finishing titanium alloy (Ti6Al4V) additively manufactured by EBM and SLS. It is shown that the micro-structured surface layer resulting from the melting process can be removed, and the surface can then be smoothed down to less than 10 nm Ra (starting from 4–5 μm Ra) using only three different diamond grit sizes. This paper also demonstrates application of the technology to freeform shapes, and documents the dimensional accuracy of finished artifacts. (paper)

Disassembly Properties of Cementitious Finish Joints Using an Induction Heating Method

Science.gov (United States)

Ahn, Jaecheol; Noguchi, Takafumi; Kitagaki, Ryoma

2015-01-01

Efficient maintenance and upgrading of a building during its lifecycle are difficult because a cementitious finish uses materials and parts with low disassembly properties. Additionally, the reuse and recycling processes during building demolition also present numerous problems from the perspective of environmental technology. In this study, an induction heating (IH) method was used to disassemble cementitious finish joints, which are widely used to join building members and materials. The IH rapidly and selectively heated and weakened these joints. The temperature elevation characteristics of the cementitious joint materials were measured as a function of several resistor types, including wire meshes and punching metals, which are usually used for cementitious finishing. The disassembly properties were evaluated through various tests using conductive resistors in cementitious joints such as mortar. When steel fiber, punching metal, and wire mesh were used as conductive resistors, the cementitious modifiers could be weakened within 30 s. Cementitious joints with conductive resistors also showed complete disassembly with little residual bond strength.

Comparison of two feeding finishing treatments on production and quality of organic beef

Directory of Open Access Journals (Sweden)

Giulio Cozzi

Full Text Available The study compared growth and slaughter performance and meat quality of organic beef cattle finished with or without pasture grazing. One group of 10 Limousin heifers was finished under confined conditions and fed ad libitum a total mixed ration based on maize silage, hay and cereal grains. A second group of 10 Limousin heifers rotationally grazed two contiguous pasture plots of 1.5 ha each with a daily supplementation of a concentrate mix based on cereal grains and roasted soybeans. Heifers were slaughtered at commercial finishing and meat quality traits were assessed on Longissimus thoracis muscle. The grazing group, due to a lower average daily gain (0.74 vs. 0.95 kg/day; P<0.05, required a prolonged finishing period (172 vs. 155 days; P<0.05 than the confined animals. Meat samples from grazing cattle were less tender (shear force: 3.92 vs. 3.24 kg/cm2; P<0.05 and showed a lower lightness (L*: 33.0 vs. 35.8; P<0.001 and a higher redness (15.4 vs. 13.7; P<0.01 and yellowness (15.6 vs. 14.6; P<0.05. Fatty acid composition of the intramuscular fat was significantly affected by the finishing system. Grazing heifers had a higher content of polyunsaturated fatty acids (4.06 vs. 3.66% of total fatty acids; P<0.05, conjugated linoleic acids (0.16 vs. 0.10% of total fatty acids; P<0.01 and ω-3 (0.44 vs. 0.30% of total fatty acids; P<0.001 than confined animals. The detrimental effects of pasture grazing on growth performance and on some important meat quality traits explain the limited adoption of this finishing system in organic beef production.

Surface texture of resin-modified glass ionomer cements: effects of finishing/polishing systems.

Science.gov (United States)

Yap, Adrian U J; Tan, W S; Yeo, J C; Yap, W Y; Ong, S B

2002-01-01

This study investigated the surface texture of two resin-modified glass ionomer cements (RMGICs) in the vertical and horizontal axis after treatment with different finishing/polishing systems. Class V preparations were made on the buccal and lingual/palatal surfaces of freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (GC) and Photac-Fil Quick (ESPE) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with 8-flute tungsten carbide burs. The teeth were then randomly divided into four groups and finished/polished with (a) Robot Carbides (RC); (b) Super-Snap system (SS); (c) OneGloss (OG) and (d) CompoSite Points (CS). The sample size for each material-finishing/polishing system combination was eight. The mean surface roughness (microm) in vertical (RaV) and horizontal (RaH) axis was measured using a profilometer. Data was subjected to ANOVA/Scheffe's tests and Independent Samples t-test at significance level 0.05. Mean RaV ranged from 0.59-1.31 and 0.83-1.52, while mean RaH ranged from 0.80-1.43 and 0.85-1.58 for Fuji II LC and Photac-Fil, respectively. Results of statistical analysis were as follows: Fuji II LC: RaV-RC, SSfinished with RC. The use of carbides (RC) and one-step rubber abrasive system (OG) for finishing/polishing of RMGICs is not recommended. Graded abrasive disk (SS) or two-step rubber abrasive (CS) systems should be used instead.

Advantages of modern collapsible systems for exterior finishing of buildings in urban areas in Russia

Directory of Open Access Journals (Sweden)

Tolstova Kristina

2017-01-01

Full Text Available Traditionally, the method of finishing interior spaces, as well as exterior surfaces and architectural and structural elements of buildings and structures is widely used, when layers of building materials or finishing structures are applied in a strict sequence, allowing them to eventually form an unbroken whole - a “monolith”. This method of finishing, its technology and results not only depend significantly on the quality of the materials used and the mechanization of processes, but also require high qualification and specialization of construction workers. The execution of such a finish is more an art than a reproduced with a given level of quality of results by a technological process. An alternative to “monolith” is a variety of collapsible (they are also called “hinged” systems for finishing urban buildings, the elements of which are manufactured in the construction industry, requiring, as a rule, only installation and assembly in internal premises (the so-called “evroremont”, Or on the external surfaces of a building or structure.

Meat goat kids finished on alfalfa, red clover or orchardgrass pastures: carcass merit and meat quality.

Science.gov (United States)

Turner, K E; Cassida, K A; Zerby, H N

2014-12-01

This experiment was conducted in 2005-2007 to evaluate carcass and chevon (goat meat) quality parameters when meat-goat kids (n=72) were finished on alfalfa (Medicago sativa L; ALF); red clover (Trifolium pratense L.; RCG); or orchardgrass (Dactylis glomerata L.; OGR) pastures. Carcass conformation score was greater (P=0.08) when meat-goat kids were finished on ALF compared to OGR with RCG intermediate. Chevon meat samples from goats finished on the three pasture treatments did not differ in ash, intramuscular fat, or crude protein content or in concentrations of omega6 and omega3 fatty acids, or the omega6 to omega3 ratio. Goats finished on OGR had higher (Pmeat-goat kids finished on ALF, RCG, or ORG produced desirable carcass weights for most niche markets in the USA. Chevon is a low-fat meat option with high desirable fatty acids for human diets. Published by Elsevier Ltd.

Evaluation of marginal fit of two all-ceramic copings with two finish lines

Science.gov (United States)

Subasi, Gulce; Ozturk, Nilgun; Inan, Ozgur; Bozogullari, Nalan

2012-01-01

Objectives: This in-vitro study investigated the marginal fit of two all-ceramic copings with 2 finish line designs. Methods: Forty machined stainless steel molar die models with two different margin designs (chamfer and rounded shoulder) were prepared. A total of 40 standardized copings were fabricated and divided into 4 groups (n=10 for each finish line-coping material). Coping materials tested were IPS e.max Press and Zirkonzahn; luting agent was Variolink II. Marginal fit was evaluated after cementation with a stereomicroscope (Leica MZ16). Two-way analysis of variance and Tukey-HSD test were performed to assess the influence of each finish line design and ceramic type on the marginal fit of 2 all-ceramic copings (α =.05). Results: Two-way analysis of variance revealed no statistically significant differences for marginal fit relative to finish lines (P=.362) and ceramic types (P=.065). Conclusion: Within the limitations of this study, both types of all-ceramic copings demonstrated that the mean marginal fit was considered acceptable for clinical application (⩽120 μm). PMID:22509119

Novel finishing concepts within BNFL'S advanced reprocessing programme

Energy Technology Data Exchange (ETDEWEB)

Hobbs, J.W.; Booth, R.; Lawson, S.; Parkes, P. [BNFL British Nuclear Fuels, Sellafield, Seascale, Cumbria, Research and Technology (United Kingdom)

2000-07-01

New methods of converting actinide nitrate solutions to oxide and fabricating the products from the reprocessing of high burn up and MOX fuels are necessary for the next generation of fuel cycle facilities in order to meet dose criteria and cost reduction targets. Options to support this include never fully separating the plutonium from the uranium and reducing decontamination factors. The product stream from such a reprocessing plant will require a finishing route capable of significant levels of automation and dose minimization. Casting of molten uranyl nitrate into pellets followed by de-nitration under vacuum has been investigated as a novel way of manufacturing oxide fuel pellets. Pellets were successfully cast over a range of temperatures and de-nitrated. Incorporation of uranium oxide into the melt was investigated to increase the density of the cast pellet. It has been demonstrated that it is possible to produce extrudates from powder and molten magnesium nitrate mixtures. Results of a preliminary study of the flow behaviour during extrusion of magnesium nitrate simulant loaded with alumina powder are also discussed. (authors)

The effect of surface finishes on outdoor granite and limestone pavers

Directory of Open Access Journals (Sweden)

Martínez-Martínez, J.

2008-06-01

Full Text Available Two types of ornamental stones, namely granite (Blanco Rafaela or Zarzalejo Granite and microcrystalline limestone (marble known commercially as Gris Pulpis, treated for different surface finishes, were tested for suitability as paving slabs. The finishes tested in both stones were polishing, hammering, honing and flaming, while acid treatment and abrasion were applied to limestone only and sawn finishes were only studied in granite.The stones were tested for the three physical properties that determine suitability for use as paving slabs; flexural strength under a concentrated load, and abrasion and slip resistance. Laboratory freeze-thaw cycle ageing tests were also conducted and flexural strength subsequently evaluated. Stone water sorption proved to be substantially unaltered by the type of finish employed. Finish barely affected flexural strength, except in the case of limestone flaming, where it was lower. Hammering was found to provide good slip resistance in both stones. The best slip performance for granite, however, was found for flamed specimens. Finish was shown to have no effect on abrasion resistance in either of the stone materials. Polished limestone suffered the least damage in freeze-thaw cycles, whereas freeze-thaw resistance was similar in all the granite specimens, regardless of the finish used.Se han estudiado, para su utilización como baldosas de pavimentos, granito (Blanco Rafaela o Granito de Zarzalejo y caliza microcristalina (mármol comercial Gris Pulpis con diferentes acabados. Estos acabados son: pulido, apomazado, abujardado y flameado en ambas rocas y además acabado al ácido y amolado en la caliza. Se han determinado mediante ensayos estandarizados las tres propiedades físicas de mayor interés para el uso de la piedra natural como baldosa en pavimentos de exteriores: resistencia a la flexión bajo carga concentrada, a la abrasión y al deslizamiento. Se han realizado ensayos de durabilidad por ciclos de hielo

IAQ performance of interior finishing products and the role of LCA

CSIR Research Space (South Africa)

Ampofo-Anti, N

2010-01-01

Full Text Available of interior finishing products to be more performance-oriented, where performance is defined in terms of the life cycle human health effects 4 . 3.0 LCA – the science-based tool Life Cycle Assessment (LCA) is a science-based tool which is designed... of interior finishing products and the role of LCA Naalamkai Ampofo-Anti, Senior Researcher, CSIR 1.0 Introduction The environmental rating and certification of products is a voluntary, market-based response by industry and business to the consumer’s...

Effects of time of change from broiler starter to broiler finisher diet on ...

African Journals Online (AJOL)

A study was conducted to determine the effect of time of change from broiler starter ration (BSR) to broiler finisher ration (BFR) on growth performance and economy of gain of meat- type chickens. Six hundred Abor Acres broiler chickens were used in an 8-week study in which same starter and finisher diets were fed but at ...

Application of eco-friendly antimicrobial finish butea monosperma leaves on fabric properties of polyester and cotton/polyester

International Nuclear Information System (INIS)

Sadaf, S.; Saeed, M.; Kalsoom, S.; Saeed, M.

2017-01-01

The study was aimed to check the effect of eco-friendly antimicrobial finish on 100% polyester and 50/50 cotton/polyester woven fabrics. The leaves' extract of Butea monosperma was used as an eco-friendly antimicrobial finish. The fabric was first desized, scoured, bleached and washed then antimicrobial finish was applied by using pad dry cure method. The aesthetic, comfort and mechanical fabrics properties were checked before and after applying antimicrobial finish. Under aesthetic property stiffness and smoothness appearance was checked, under comfort related property absorbency and air permeability was checked and under mechanical property tear and tensile strength was checked. The antimicrobial finish was checked by using ASTEM E2149 Shake Flask method. The AATCC and ISO standard testing methods were used for checking fabric properties. One way ANOVA statistical test was applied for analysis of results. Antimicrobial finish has increased aesthetic (stiffness, smoothness appearance), comfort (absorbency, air permeability) and mechanical (tensile and tear strengths) properties of polyester and cotton/polyester fabrics. The antimicrobial finish was effective on both 100% polyester and 50/50 cotton/polyester fabrics up to 25 washes. This study is beneficial to medical industry, paramedical staff, sports wears, home furnishing as well as common people. (author)

Numerical simulation of the combination effect of external magnetic field and rotating workpiece on abrasive flow finishing

Energy Technology Data Exchange (ETDEWEB)

Kheradmand, Saeid; Esmailian, Mojtaba; Fatahy, A. [Malek-Ashtar University of Technology (MUT), Isfahan (Iran, Islamic Republic of)

2017-04-15

Finishing of a workpiece is a main process in the production. This affects the quality and lifetime. Finishing in order of nanometer, nowadays, is a main demand of the industries. Thus, some new finishing process, such as abrasive flow finishing, is introduced to respond this demand. This may be aided by rotating workpiece and imposing a magnetic field. Numerical simulation of this process can be beneficial to reduce the expense and predict the result in a minimum time. Accordingly, in this study, magnetorheological fluid finishing is numerically simulated. The working medium contains magnetic and abrasive particles, blended in a base fluid. Some hydrodynamic parameters and surface roughness variations are studied. It is found that combination of rotating a workpiece and imposing a magnetic field can improve the surface roughness up to 15 percent.

Knowledge acquisition for nuclear power plant unit diagnostic system

International Nuclear Information System (INIS)

Li Xiaodong; Xi Shuren

2003-01-01

The process of acquiring knowledge and building a knowledge base is critical to realize fault diagnostic system at unit level in a nuclear power plant. It directly determines whether the diagnostic system can be applied eventually in a commercial plant. A means to acquire knowledge and its procedures was presented in this paper for fault diagnostic system in a nuclear power plant. The work can be carried out step by step and it is feasible in a commercial nuclear power plant. The knowledge base of the fault diagnostic system for a nuclear power plant can be built after the staff finish the tasks according to the framework presented in this paper

Reliability of lead-free solder joints with different PCB surface finishes under thermal cycling

Energy Technology Data Exchange (ETDEWEB)

Xia Yanghua [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)], E-mail: xia_yanghua@hotmail.com; Xie Xiaoming [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)

2008-04-24

The reliability of lead-free electronic assemblies under thermal cycling was investigated. Thin small outline package (TSOP) devices with FeNi leads were reflow soldered on FR4 PCB (printed circuit board) with Sn3.0Ag0.5Cu (wt%) solder. The effects of different PCB finishes (organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG)) were studied. The results show that OSP finish reveals better performance than its ENIG counterparts. The crack originates at the fringe of heel fillet in both cases. The propagation of crack in the ENIG case is along the device/solder interface, while in the case of OSP, the crack extends parallel to the solder/PCB interface. When the OSP finishes are employed, many Cu6Sn5 precipitates form inside the bulk solder and have a strengthening effect on the solder joint, resulting in better reliability performance as compared to those with ENIG finishes.

Study on mycoflora of poultry feed ingredients and finished feed in Iran

OpenAIRE

Seyed Soheil Ghaemmaghami; Mehrdad Modirsaneii; Alireza Khosravi; Mehdi Razzaghi-Abyaneh

2016-01-01

 Background and Objectives: Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi.Materials and Methods: Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e....

Effects of forage species or concentrate finishing on animal performance, carcass and meat quality.

Science.gov (United States)

Duckett, S K; Neel, J P S; Lewis, R M; Fontenot, J P; Clapham, W M

2013-03-01

Angus-cross steers (n = 128; initial BW = 270 ± 3.8 kg) were used in a 3-yr study to assess effects of forage species grazed before slaughter versus concentrate finishing on carcass and meat quality. At the completion of the stockering phase, steers were randomly allotted to mixed pasture (MP; n = 36/yr) or corn-silage concentrate (CON; n = 12/yr) finishing treatments. At 40 d before harvest, MP steers were randomly divided into 3 forage species treatments: alfalfa (AL), pearl millet (PM), or mixed pasture (MP). Average daily BW gain was greater (P = 0.001) for CON than for forage-finished (FOR) steers during the early and overall finishing phase. During the late finishing phase when FOR steers were grazing difference forage species, ADG was greater (P = 0.03) for PM than MP or AL. Harvest weight and HCW were greater (P animal performance. Total fat percentage of the 9th to 11th rib section was 46% less(P = 0.028) for FOR than CON due to reductions (P 0.78) between CON and FOR and were not altered (P > 0.40) by forage species. Trained sensory panel juiciness, initial tenderness, and overall tenderness scores did not differ (P > 0.17) by finishing treatment or forage species. Beef flavor intensity was greater (P 0.05) total lipid content of the LM. Oleic acid concentration and total MUFA of the LM were 21% and 22% less (P = 0.001) for FOR than CON. Concentrations of all individual [linolenic acid, eicosapentaenoic (EPA), docosapentaenoic (DPA), and docosadexaenoic (DHA) acids] and total n-3 fatty acids were greater (P carcass weight with same time endpoints and accelerates deposition of MUFA in comparison with FOR, which reduces carcass weight and fat deposition but maintains high concentrations of n-3 and CLA fatty acids. Finishing system or forage species grazed 40 d before slaughter did not alter beef tenderness but FOR had greater off-flavors according to both trained and descriptive sensory panelists.

Mutational synergism between p-fluorophenylalaline and UV in Coprinus lagopus

International Nuclear Information System (INIS)

Talmud, P.J.

1977-01-01

The amino acid analogue p-fluorophenylalanine (PFP) is mutagenic to Coprinus lagopus due to its incorporation into proteins. Spontaneous mutations, PFP and UV mutagenesis and PFP/UV synergism have been studied in a UV resistant strain and in two complementing UV sensitive mutant strains. By comparison to the UV resistant strain, one UV sensitive strain shows normal spontaneous mutations, 1.4% PFP-induced mutations and 50-fold UV mutagenesis. The second UV sensitive strain has 19-fold spontaneous mutation frequency and slightly elevated UV mutagenesis. In all 3 strains the PFP/UV synergism is comparable (4-5 times the arithmetic expected). The results indicate that PFP mutagenesis is due to the incorporation of PFP into enzymes normally functioning in the organism but which also participate in UV repair mechanisms. A model is proposed for UV repair which is based on a PFP sensitive excision repair system of at least two enzymes, an alternative 'error-proof' pathway which is not susceptible to PFP and an 'error-prone' pathway which is responsible for UV mutagenesis and is susceptible to PFP as shown by the PFP/UV synergism. Because PFP is given before UV treatment, this implies a UV inducible cofactor and a PFP sensitive enzyme which only functions after UV activation

System requirement specifications for the Z-plant materials information tracking system (ZMITS)

International Nuclear Information System (INIS)

NEGIN, C.A.

1999-01-01

This is a system requirement specification for a database which will be developed to track classified information related to nuclear materials stored at PFP. The system will supplement existing databases to support both processing and disposition information needs

Glufosinate herbicide-tolerant (LibertyLink) rice vs. conventional rice in diets for growing-finishing swine.

Science.gov (United States)

Cromwell, G L; Henry, B J; Scott, A L; Gerngross, M F; Dusek, D L; Fletcher, D W

2005-05-01

Genetically modified (GM) rice (LibertyLink, event LLRICE62) that is tolerant to glufosinate ammonium (Liberty) herbicide was compared with a near-isogenic (NI) conventional medium-grain brown rice (cultivar, Bengal) and a commercially milled long-grain brown rice in diets for growing-finishing pigs. The GM and NI rice were grown in 2000. The GM rice was from fields treated (GM+) or not treated (GM-) with glufosinate herbicide. The GM- and NI rice were grown using herbicide regimens typical of southern United States rice production practices. The four rice grains were similar in composition. Growing-finishing pigs (n = 96) were fed fortified rice-soybean meal diets containing the four different rice grains from 25 to 106 kg BW. Diets contained 0.99% lysine initially (growing phase), with lysine decreased to 0.80% (early finishing phase) and 0.65% (late finishing phase), when pigs reached 51 and 77 kg, respectively. The percentage of rice in the four diets was constant during each of the three phases (72.8, 80.0, and 85.8% for the growing, early-finishing, and late-finishing phases, respectively). There were six pen replicates (three pens of barrows and three pens of gilts) and four pigs per pen for each dietary treatment. All pigs were slaughtered at the termination of the study to collect carcass data. At the end of the 98-d experiment, BW gain, feed intake (as-fed basis), and feed:gain ratio did not differ (P > 0.05) for pigs fed the GM+ vs. conventional rice diets, but growth performance traits of pigs fed the GM+ rice diets were superior (P glufosinate herbicide-tolerant rice was similar in composition and nutritional value to conventional rice for growing-finishing pigs.

Pengaruh berbagai jenis penyamakan dan tipe finish terhadap morfologi, sifat organoleptis dan mekanis kulit biawak (Varanus salvator

Directory of Open Access Journals (Sweden)

Emiliana Kasmudjiastuti

2015-12-01

Full Text Available Monitor lizard (Varanus salvator skin is exotic leather because it has a unique grain. Therefore, the original grain of the animal needs to be maintained in the finishing process so that its performances look likes natural. This research aimed to study the effect of tanning materials (vegetable and chrome and the type of finish (natural, aniline, semi-aniline and two tone on morphology, organoleptic and mechanical properties of lizard skin. The materials used in this study were dry preserved lizard skins. The research varied on the types of tanning (vegetable and chrome and the type of finish (natural, aniline, semi-aniline and two tone each by varying the finishing materials (casein and protein binders. The tests were conducted on the observation of the structure using photomicrographs, rub fastness, adhesion of finish strength, tensile strength, elongation at break and organoleptic. The results showed that the best result was vegetable tanned lizard skin using natural finish with casein and met the requirements of SNI 06-4362-1996, lizard skin for shoe upper. This gave dry and wet rub fastness of 5 and 5 respectively; dry and wet adhesion of finish strength of 650 and 100 g/cm respectively; tensile strength of 207.43 kg/cm2; elongation at break of 37.52% and organoleptic value of panelists observations of 87.9 (good.

Study on mycoflora of poultry feed ingredients and finished feed in Iran.

Science.gov (United States)

Ghaemmaghami, Seyed Soheil; Modirsaneii, Mehrdad; Khosravi, Ali Reza; Razzaghi-Abyaneh, Mehdi

2016-02-01

Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi. Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e. Tehran, Alborz and Qom in Iran from October 2014 to January 2015. Samples were cultured on Sabouraud dextrose agar (SDA), Aspergillus flavus and parasiticus agar (AFPA) and dichloran rosebengal chloramphenicol agar (DRBC) and incubated at 28 °C for 7-10 days. Purified fungal colonies were identified by a combination of macro- and microscopic morphological criteria. For determining the rate of fungal contamination, samples were cultured on SDA and colony forming units (CFUs) were calculated. A total of 384 fungal isolates belonging to 7 genera of filamentous fungi and yeasts were obtained from corn (124 isolates), soybean meal (92 isolates), and feed before (72 isolates), and after pelleting (96 isolates). The most prominent fungal isolate in corn, soybean meal and feed before pelleting (feed as mash form) was Fusarium but in feed after pelleting was Aspergillus. Among 5 Aspergillus species isolated, potentially aflatoxigenic A. flavus isolates was predominant in corn (46.6%), soybean meal (72.7%) and poultry finished feed (75%). CFUs results indicated that 9/22 corn samples (40.9%), none of 22 soybean meal samples, 19/41 finished feed (46.3%) were contaminated higher than the standard limit. Our results indicated that corn, soybean meal and finished feed of poultry feed mill are contaminated with various fungal genera by different levels sometimes higher that the standard limits. Contamination with potentially mycotoxigenic fungi especially Aspergillus species may be considered as a human public health hazard.

Concentration data for anthropogenic organic compounds in groundwater, surface water, and finished water of selected community water systems in the United States, 2002-10

Science.gov (United States)

Carter, Janet M.; Kingsbury, James A.; Hopple, Jessica A.; Delzer, Gregory C.

2010-01-01

The National Water-Quality Assessment Program of the U.S. Geological Survey began implementing Source Water-Quality Assessments (SWQAs) in 2001 that focus on characterizing the quality of source water and finished water of aquifers and major rivers used by some of the larger community water systems in the United States. As used in SWQA studies, source water is the raw (ambient) water collected at the supply well before water treatment (for groundwater) or the raw (ambient) water collected from the river near the intake (for surface water), and finished water is the water that has been treated and is ready to be delivered to consumers. Finished-water samples are collected before the water enters the distribution system. The primary objective of SWQAs is to determine the occurrence of more than 250 anthropogenic organic compounds in source water used by community water systems, many of which currently are unregulated in drinking water by the U.S. Environmental Protection Agency. A secondary objective is to understand recurrence patterns in source water and determine if these patterns also occur in finished water before distribution. SWQA studies were conducted in two phases for most studies completed by 2005, and in one phase for most studies completed since 2005. Analytical results are reported for a total of 295 different anthropogenic organic compounds monitored in source-water and finished-water samples collected during 2002-10. The 295 compounds were classified according to the following 13 primary use or source groups: (1) disinfection by-products; (2) fumigant-related compounds; (3) fungicides; (4) gasoline hydrocarbons, oxygenates, and oxygenate degradates; (5) herbicides and herbicide degradates; (6) insecticides and insecticide degradates; (7) manufacturing additives; (8) organic synthesis compounds; (9) pavement- and combustion-derived compounds; (10) personal-care and domestic-use products; (11) plant- or animal-derived biochemicals; (12) refrigerants and

Conversion of Ulba Metallurgy Plant

International Nuclear Information System (INIS)

Onoprienko, O.

1996-01-01

General Information 'Ulba Metallurgical plant' Joint Stock Company successfully operates for more than 46 years. The plant was established by MINSREDMASH, USSR and at the present moment has finished complexes for production of nuclear fuel for atomic power stations, tantalum and superconducting materials production, beryllium, hydrofluoric acid manufacture and engineering production. Problem Essence In spite of the monopoly possession of tantalum manufacture, beryllium and uranium fuel, superconducting materials in Commonwealth of Independent States countries, company has serious financial problems due to the critical situation in Commonwealth of Independent States countries, production ties collapse and fast market demand decrease for the Ulba Metallurgical Plant Joint Stock Company products. The alternative decision is to create substitute productions, conversion integrating and introducing new products to the world market

High Speed Finish Turning of Inconel 718 Using PCBN Tools under Dry Conditions

Directory of Open Access Journals (Sweden)

José Luis Cantero

2018-03-01

Full Text Available Inconel 718 is a superalloy, considered one of the least machinable materials. Tools must withstand a high level of temperatures and pressures in a very localized area, the abrasiveness of the hard carbides contained in the Inconel 718 microstructure and the adhesion tendency during its machining. Mechanical properties along with the low thermal conductivity become an important issue for the tool wear. The finishing operations for Inconel 718 are usually performed after solution heat treatment and age hardening of the material to give the superalloy a higher level of hardness. Carbide tools, cutting fluid (at normal or high pressures and low cutting speed are the main recommendations for finish turning of Inconel 718. However, dry machining is preferable to the use of cutting fluids, because of its lower environmental impact and cost. Previous research has concluded that the elimination of cutting fluid in these processes is feasible when using hard carbide tools. Recent development of new PCBN (Polycrystalline Cubic Boron Nitride grades for cutting tools with higher tenacity has allowed the application of these tool grades in the finishing operations of Inconel 718. This work studies the performance of commercial PCBN tools from four different tool manufacturers as well as an additional grade with equivalent performance during finish turning of Inconel 718 under dry conditions. Wear tests were carried out with different cutting conditions, determining the evolution of machining forces, surface roughness and tool wear. It is concluded that it is not industrially viable the high-speed finishing of Inconel 718 in a dry environment.

Radiation technology in finishing process improves health, safety and environment (HSE) in the furniture manufacturing industry

International Nuclear Information System (INIS)

Ahmad Shakri Mat Seman

1999-01-01

In furniture manufacturing, processes like cross cutting, molding, planning, shaping, turning, assembling and finishing are involved. The most significant types of negative impact of these processes are such as dust emission, noise, hazardous work, health risk, emission of organic solvent, toxic chemicals emission and chemical waste. In the finishing process, a number of negative effects that will cause health, safety and environmental (HSE) performance. This article highlights the environmental problems in the furniture finishing processes and how the radiation technology can reduce these negative impacts. The drawbacks that hamper the manufacturers from adopting this technology are also discussed. The objective of the paper is to create the awareness among the industrialist and consumers on the HSE hazardous in furniture finishing and steps can be taken to improve

"Miss! I'm Done!" Finishing Craft Assignments as a Situated Activity System in Preschool

Science.gov (United States)

Deunk, Marjolein; Berenst, Jan; de Glopper, Kees

2010-01-01

We describe the Situated Activity System of finishing craft assignments in preschool: the specific, routinized way that child and teacher jointly close the child's craft assignment, employing a specific discourse pattern. We analyzed the interactions of 14 Dutch children between 2.1 and 3.10 years old while they were finishing their craft…

Study of the binary mixtures of {monoglyme + (hexane, cyclohexane, octane, dodecane)} by ECM-average and PFP models

International Nuclear Information System (INIS)

Rivas, M.A.; Buep, A.H.; Iglesias, T.P.

2015-01-01

Highlights: • Polarization of the real mixture is less than that of the ideal mixture. • Molar excess volume does not exert the dominant effect on the polarization of the mixture. • Similar influence of molecular interactions on the behaviour of excess permittivity. • Excess molar volume is more influenced by the interactions than excess permittivity. - Abstract: Excess molar volumes and excess permittivity of binary mixtures involving monoglyme and alkanes, such as n-hexane, cyclohexane, n-octane and n-dodecane, were calculated from density and relative permittivity measurements for the entire composition range at several temperatures (288.15, 298.15 and 308.15) K and atmospheric pressure. The excess permittivity was calculated on the basis of a recent definition considering the ideal volume fraction. Empirical equations for describing the experimental data in terms of temperature and concentration are given. The experimental values of permittivity have been compared with those estimated by well-known models from literature. The results have indicated that better predictions are obtained when the volume change on mixing is incorporated in these calculations. The contribution of interactions to the excess permittivity was analysed by means of the ECM-average model. The Prigogine–Flory–Patterson (PFP) theory of the thermodynamics of solutions was used to shed light on the contribution of interactions to the excess molar volume. The work concludes with an interpretation of the information given by the theoretical models and the behaviour of both excess magnitudes

Effects of finishing diet and pre-slaughter fasting time on meat quality in crossbred pigs

Directory of Open Access Journals (Sweden)

K. PARTANEN

2008-12-01

Full Text Available The effects of the carbohydrate composition of finishing diet (fed from 80 to 107 kg of body weight and the length of pre-slaughter fasting on pork quality were studied in a 2 × 2 factorial experiment with 80 crossbred pigs. The control finishing diet was based on barley and soybean meal, and the fibrous finishing diet was based on barley, barley fibre, faba beans, and rapeseed cake. These diets contained 465 and 362 g starch and 177 and 250 g dietary fibre per kg, respectively. The fasting times of 25 and 41 h were obtained by giving the pigs their last meal at different times. Longer fasting lowered the glycolytic potential of the longissimus lumborum muscle (P = 0.01, whereas the finishing diet had no effect. Different muscles responded differently to the treatments. Longer fasting increased the ultimate pH of the semimembranosus muscle (P = 0.02, but did not affect that of the longissimus lumborum and semispinalis capitis muscles. The finishing diets did not affect the ultimate pH of the investigated muscles. A diet × fasting time interaction was seen in the lightness of the semimembranosus muscle (P = 0.05. The fibrous diet resulted in darker meat than the control diet did in pigs that were fasted for 25 h (P < 0.05. Longer fasting darkened the meat colour in pigs fed the fibrous diet (P < 0.05 but not in those fed the control diet. The meat from the semispinalis capitis muscle was darker in pigs fed the fibrous than those fed the control diet (P = 0.04. The treatments did not affect the colour of the longissimus lumborum muscle. Longer fasting decreased drip loss from the meat of pigs fed the control diet (P < 0.05. The eating quality of the pork was not influenced by the finishing diets or the fasting time. The pigs also grew equally fast on both finishing diets. In conclusion, a moderate alteration in the carbohydrate composition of a finishing diet or longer pre-slaughter fasting can have some effects on pork quality in crossbred pigs

Finished Genome Sequence of Collimonas arenae Cal35

NARCIS (Netherlands)

Wu, Je-Jia; de Jager, Victor; Deng, Wen-ling; Leveau, Johan

2015-01-01

We announce the finished genome sequence of soil forest isolate Collimonas arenae Cal35, which comprises a 5.6-Mbp chromosome and 41-kb plasmid. The Cal35 genome is the second one published for the bacterial genus Collimonas and represents the first opportunity for high-resolution comparison of

Wean-to-finish feeder space availability effects on nursery and finishing pig performance and total tract digestibility in a commercial setting when feeding dried distillers grains with solubles.

Science.gov (United States)

Weber, E K; Stalder, K J; Patience, J F

2015-04-01

The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P feeder space allowance did not impact pig performance during the nursery or grow-finish production phases. Inclusion of DDGS at higher levels will decrease ADFI but not ADG or efficiency when isocaloric diets are fed. The inclusion level of DDGS does impact HCW and percent

77 FR 61025 - Certain Prepregs, Laminates, and Finished Circuit Boards: Notice of Institution of Formal...

Science.gov (United States)

2012-10-05

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-659] Certain Prepregs, Laminates, and Finished..., and the sale within the United States after importation of certain prepregs, laminates, and finished... for sale, and selling for importation into the United States prepregs and laminates that are the...

Genotype x environment interactions for fatty acid profiles in Bos indicus and Bos taurus finished on pasture or grain.

Science.gov (United States)

Bressan, M C; Rossato, L V; Rodrigues, E C; Alves, S P; Bessa, R J B; Ramos, E M; Gama, L T

2011-01-01

A study was conducted to characterize lipid profiles in the M. longissimus thoracis of commercial Brazilian beef and to assess how those profiles are influenced by finishing system, genetic group, and their interaction. Intramuscular fat (IMF) and fatty acid (FA) profiles were determined in 160 bulls of the Bos taurus (n = 75) and Bos indicus (n = 85) genetic groups, finished on pasture (n = 46) or with grain supplementation (n = 114) and slaughtered in a commercial abattoir. Finishing system had a major impact on the deposition of IMF, as well as on the concentration of SFA, PUFA, and their ratio, but genetic groups showed important differences in the ability to convert SFA into cis-9 MUFA and to convert 16:0 into 18:0. When compared with pasture-finished animals, those finished with grain had greater content of IMF and SFA (P 0.05), and about one-half the amount of PUFA (P 0.05). With pasture-finishing, no differences were observed among the 2 genetic groups in SFA and MUFA (P > 0.05), but PUFA were decreased in B. taurus (P genetic groups were compared in grain-finishing, B. taurus had a decreased ability for elongation and B. indicus had a decreased aptitude for desaturation of FA. On the other hand, with pasture-finishing a greater deposition of intermediate FA from ruminal biohydrogenation was observed in B. indicus than in B. taurus. Overall, FA profiles were affected more by finishing system in B. indicus than in B. taurus.

Influence of core-finishing intervals on tensile strength of cast posts-and-cores luted with zinc phosphate cement

Directory of Open Access Journals (Sweden)

Michele Andrea Lopes Iglesias

2012-08-01

Full Text Available The core finishing of cast posts-and-cores after luting is routine in dental practice. However, the effects of the vibrations produced by the rotary cutting instruments over the luting cements are not well-documented. This study evaluated the influence of the time intervals that elapsed between the cementation and the core-finishing procedures on the tensile strength of cast posts-and-cores luted with zinc phosphate cement. Forty-eight bovine incisor roots were selected, endodontically treated, and divided into four groups (n = 12: GA, control (without finishing; GB, GC, and GD, subjected to finishing at 20 minutes, 60 minutes, and 24 hours after cementation, respectively. Root canals were molded, and the resin patterns were cast in copper-aluminum alloy. Cast posts-and-cores were luted with zinc phosphate cement, and the core-finishing procedures were applied according to the groups. The tensile tests were performed at a crosshead speed of 0.5 mm/min for all groups, 24 hours after the core-finishing procedures. The data were subjected to one-way analysis of variance (ANOVA and Tukey's test (α = 0.05. No significant differences were observed in the tensile strengths between the control and experimental groups, regardless of the time interval that elapsed between the luting and finishing steps. Within the limitations of the present study, it was demonstrated that the core-finishing procedures and time intervals that elapsed after luting did not appear to affect the retention of cast posts-and-cores when zinc phosphate cement was used.

Affecting microclimate in surroundings of nuclear power plants

International Nuclear Information System (INIS)

Skulec, S.; Janiskova, M.

1990-01-01

The influence of nuclear power plants on regional climate was observed and studied. Cooling towers emit waste heat and humidity and the resulting primary effects consist of local changes in air temperature and humidity. Secondary effects could be changes in all meteorologic parameters depending on the primary changes. A series of mathematical models was created to evaluate long-term climate changes depending on the power range, type of cooling, regional climate, etc. The first generation of the models, finished in 1986, was based on conservative estimates of the effects observed. The second generation was developed between 1986 and 1988 and should provide more realistic values. Simulated results were compared with the observed data. Although the verification of the models has not yet been finished, the agreement between the simulated results and the observed values seems to be good. The results show that the influence of nuclear power plants on the climate is almost not observable and cannot be registered by usual measuring methods. (J.J.). 4 figs., 2 tabs., 6 refs

Effect of surface finishing on the oxidation behaviour of a ferritic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Ardigo-Besnard, M.R., E-mail: maria-rosa.ardigo-besnard@u-bourgogne.fr [Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR 6303 CNRS—Université de Bourgogne Franche-Comté, BP 47870, 21078 Dijon Cedex (France); Popa, I.; Heintz, O.; Chassagnon, R. [Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR 6303 CNRS—Université de Bourgogne Franche-Comté, BP 47870, 21078 Dijon Cedex (France); Vilasi, M. [Institut Jean Lamour, UMR 7198 CNRS—Université de Lorraine, Parc de Saurupt, 54011 Nancy (France); Herbst, F. [Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR 6303 CNRS—Université de Bourgogne Franche-Comté, BP 47870, 21078 Dijon Cedex (France); Girardon, P. [APERAM, Centre de Recherche, BP15, 62330 Isbergues (France); Chevalier, S. [Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR 6303 CNRS—Université de Bourgogne Franche-Comté, BP 47870, 21078 Dijon Cedex (France)

2017-08-01

Highlights: • Study of surface finishing effect on the corrosion behaviour of a stainless steel. • Mirror polished samples were compared to as-rolled material. • Two oxidation mechanisms were identified depending on the surface finishing. • Before oxidation, native chemical phases are identical for both samples. • Subsurface dislocations generated by the polishing process promote Cr{sub 2}O{sub 3} formation. - Abstract: The corrosion behaviour and the oxidation mechanism of a ferritic stainless steel, K41X (AISI 441), were evaluated at 800 °C in water vapour hydrogen enriched atmosphere. Mirror polished samples were compared to as-rolled K41X material. Two different oxidation behaviours were observed depending on the surface finishing: a protective double (Cr,Mn){sub 3}O{sub 4}/Cr{sub 2}O{sub 3} scale formed on the polished samples whereas external Fe{sub 3}O{sub 4} and (Cr,Fe){sub 2}O{sub 3} oxides grew on the raw steel. Moreover, isotopic marker experiments combined with SIMS analyses revealed different growth mechanisms. The influence of surface finishing on the corrosion products and growth mechanisms was apprehended by means of X-ray photoelectron spectroscopy (XPS) and residual stress analyses using XRD at the sample surfaces before ageing.

Performance and nutrient utilization of cockerel finishers fed graded ...

African Journals Online (AJOL)

RMW) on performance and nutrient utilization of cockerel finishers. One hundred and fifty 9-week old Black Harco cockerels were raised on five experimental diets where RMW replaced maize at graded levels and designated diet 1 (0% RMW); diet ...

Response of finishing broiler chickens to supplemental Neem ...

African Journals Online (AJOL)

An eight weeks feeding trial was conducted to investigate the effects of feeding diets containing Neem Leaf Meal (NLM), Garlic Meal (GM) and their combinations (NLM +GM) on oocyst count, bacteria count and gut morphology of finishing broiler chickens. A total of 180 day-old Cobb broiler chickens were divided into twelve ...

Fiber Finishes for Improving Galvanic Resistance of Imide-Based Composites

National Research Council Canada - National Science Library

Allred, R. E

1998-01-01

The objective of this program is the development and demonstration of galvanic corrosion resistant carbon/ BMI composites through the use of reactive finishes to form coatings that isolate the carbon...

Fatty acid metabolism and deposition in subcutaneous adipose tissue of pasture and feedlot finished cattle

Science.gov (United States)

An experiment was conducted to evaluate the effects of pasture finishing versus high-concentrate finishing, over time, on fatty acid metabolism in Angus crossbred (n = 24) steers. Ruminal fluid, serum, and adipose tissue biopsies were obtained on d 0, 28, 84, and 140. Pasture forages and diet ingr...

Influence of Finishing and Polishing Techniques and Abrasion on Transmittance and Roughness of Composite Resins.

Science.gov (United States)

Carneiro, Pma; Ramos, T M; de Azevedo, C S; de Lima, E; de Souza, Shj; Turbino, M L; Cesar, P F; Matos, A B

The aim of this study was to evaluate the influence of finishing and polishing systems and toothbrush abrasion on transmittance (T) and surface roughness (Ra) of three composite resins (Filtek Z350 XT, Tetric N-Ceram, and IPS Empress Direct). Eighteen resin disks (10 mm diameter × 2 mm thick) finished by polyester strips had initial surface smoothness recorded, representing phase 1 (P1). Specimens were divided into three groups (n=6) according to the finishing/polishing instrument used (OneGloss, TopGloss, and Sof-Lex) to compose phase 2 samples (P2). Then specimens were subjected to 514 cycles of toothbrush simulation using a toothpaste slurry, with a constant load applied to soft bristles, and were then washed (phase 3=P3). After each phase, the specimens were examined by an optical profiler and spectrophotometer to measure Ra and T. Data were analyzed by analysis of variance, Tukey and Pearson tests. T values were statistically influenced by composite resin ( p=0.000) and phase of measurement ( p=0.000) factors, while the finishing/polishing system used ( p=0.741) did not affect T. On the other hand, Ra values were statistically affected by the factor finishing/polishing system ( p=0.000), but not by composite resin ( p=0.100) and phase of measurement ( p=0.451). Tetric N-Ceram and Empress Direct presented higher values of roughness when polished by OneGloss, while TopGloss and Sof-Lex showed a lower roughness. It can be concluded that composite resins transmitted more light after dental abrasion. Transmittance of composite resins was not modified by the distinct roughness created by finishing/polishing instruments.

40 CFR 63.5390 - How do I measure the HAP content of a finish?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I measure the HAP content of a... Initial Compliance Requirements § 63.5390 How do I measure the HAP content of a finish? (a) To determine the HAP content of a finish, the reference method is EPA Method 311 of appendix A of 40 CFR part 63...

A case study of printing industry plant layout for effective production

Science.gov (United States)

Viswajit, T.; Teja, T. Ravi; Deepthi, Y. P.

2017-07-01

This paper presents the overall picture of the processes happening in printing industry. This research is aimed to improve the plant layout of existing plant. The travel time was reduced by relocating machinery. Relocation is based on systematic layout planning (SLP). The complete process of raw material entering the industry to dispatching of finished product is shown in 3-D Flow diagram. The process happening in each floor explained in detail using Flow Process chart. Travel time is reduced by 25% after modifying existing plant layout.

WOOD PROPERTIES AND EFFECT OF WOOD PROPERTIES ON THE WOOD FINISHING

Directory of Open Access Journals (Sweden)

Abdulkadir Malkoçoğlu

2006-04-01

Full Text Available Wood is basic raw material for furniture and joinery industries with wood structures. Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth condition, size of the tree at harvest, sawing, and other manufacturing processes. Wood properties have been characterized within two groups as natural and manufacturing factors that effects finishing performance. Grow rate, density, knots, moisture content, extractives and juvenile wood are natural characteristics. Grain orientation, texture, drying and performance expectations are manufacturing characteristics. In this review, the effects of natural and manufacturing characteristics are discussed on the surface finishing performance of wood.

Addendum 1 to CSER 96-025: PFP storage of 9.25/9.5 inch tall, 4.4 kg Pu cans on existing Vault 4 pedestals

International Nuclear Information System (INIS)

Hillesland, K.E.

1997-01-01

A nuclear criticality safety analysis has been performed to increase the approved plutonium mass limit for cans stored in Vault number-sign 4 cubicles at PFP. The original CSER 96-025 accommodated the storage of 4.4 kg of plutonium in PuO, (5.0 kg PuO,) in Vault number-sign 4 by requiring that half the cubicles be left vacant. This addendum allows for all the cubicles to be used, but with a fissile plutonium mass limit of 58 kg per cubicle. A mass limit for each cubical allows for storage of a larger number of cans if some have less than the 4.4 kg Pu limit per can. The highest k., calculated is 0.932 + 0.003 when an overbatched can is present in every fourth cubicle. This is below the criticality safety limit of kff 0.935, and consequently, an increase of plutonium mass to 4.4 kg per can is within acceptable safety limits for the given mass limit

Problems of power plant capital demands

International Nuclear Information System (INIS)

Slechta, V.; Bohal, L.

1986-01-01

The problems are discussed of requirements for investment for power plants in Czechoslovakia. Since the construction was finished of coal-burning 110 MW power plants with six power units, specific capital cost has steadily been growing. The growth amounts to 6 to 8% per year while the principle has been observed that specific capital cost decreases with increased unit power. Attention is paid to the cost of the subcontractors of the building and technological parts of a power plant and to the development of productivity of labour. A comparison is tabulated of cost for coal-burning power plants with 100 MW and 200 MW units and for nuclear power plants with WWER-440 reactors. Steps are suggested leading to a reduction of the capital cost of nuclear power plants. It is stated that should not these steps be taken, the envisaged development of nuclear power would be unbearable for the Czechoslovak national economy. (Z.M.). 8 tabs., 3 refs

Sensory quality of beef from different finishing diets.

Science.gov (United States)

Resconi, V C; Campo, M M; Font i Furnols, M; Montossi, F; Sañudo, C

2010-11-01

Beef production under different local husbandry systems might have meat sensory quality implications for the marketing of these products abroad. In order to assess the effect of finishing diet systems on beef quality, a trained sensory taste panel assessed meat aged for 20 days from 80 Uruguayan Hereford steers that were finished on one of the following diets: T1=Pasture [4% of animal live weight (LW)], T2=Pasture [3% LW plus concentrate (0.6% LW)], T3=Pasture [3% LW plus concentrate (1.2% LW)], or T4=Concentrate plus hay ad libitum. Beef odour and flavour intensities decreased with an increase in the energy content of the diet. The meat from T2 had the lowest acid flavour and strange odours intensities. In general, steers fed only concentrate plus hay (T4) produced meat that had an inferior sensory quality because they had more pronounced off-flavours and was tougher. Copyright © 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

Finish line distinctness and accuracy in 7 intraoral scanners versus conventional impression: an in vitro descriptive comparison.

Science.gov (United States)

Nedelcu, Robert; Olsson, Pontus; Nyström, Ingela; Thor, Andreas

2018-02-23

Several studies have evaluated accuracy of intraoral scanners (IOS), but data is lacking regarding variations between IOS systems in the depiction of the critical finish line and the finish line accuracy. The aim of this study was to analyze the level of finish line distinctness (FLD), and finish line accuracy (FLA), in 7 intraoral scanners (IOS) and one conventional impression (IMPR). Furthermore, to assess parameters of resolution, tessellation, topography, and color. A dental model with a crown preparation including supra and subgingival finish line was reference-scanned with an industrial scanner (ATOS), and scanned with seven IOS: 3M, CS3500 and CS3600, DWIO, Omnicam, Planscan and Trios. An IMPR was taken and poured, and the model was scanned with a laboratory scanner. The ATOS scan was cropped at finish line and best-fit aligned for 3D Compare Analysis (Geomagic). Accuracy was visualized, and descriptive analysis was performed. All IOS, except Planscan, had comparable overall accuracy, however, FLD and FLA varied substantially. Trios presented the highest FLD, and with CS3600, the highest FLA. 3M, and DWIO had low overall FLD and low FLA in subgingival areas, whilst Planscan had overall low FLD and FLA, as well as lower general accuracy. IMPR presented high FLD, except in subgingival areas, and high FLA. Trios had the highest resolution by factor 1.6 to 3.1 among IOS, followed by IMPR, DWIO, Omnicam, CS3500, 3M, CS3600 and Planscan. Tessellation was found to be non-uniform except in 3M and DWIO. Topographic variation was found for 3M and Trios, with deviations below +/- 25 μm for Trios. Inclusion of color enhanced the identification of the finish line in Trios, Omnicam and CS3600, but not in Planscan. There were sizeable variations between IOS with both higher and lower FLD and FLA than IMPR. High FLD was more related to high localized finish line resolution and non-uniform tessellation, than to high overall resolution. Topography variations were low

Development of Dukovany nuclear power plant

International Nuclear Information System (INIS)

Kouklik, I.

2000-01-01

The presentation evaluates the present situation of the Dukovany nuclear power plant operation. It analyses the present at the plant, and also in both the near and distant localities. Based on these analyses the conclusions and targets that are necessary for keeping the plant's safe operation are made. From the current situation the report about the results of the year 1999 in the operation and financial field, stress on the safety index, is presented. Further, there is a list of finished and semi-finished activities that are taking place within the harmonization of the Dukovany NPP. At the same time the report presents the terms of licensing and the going of implementation of the 'KAPA' project - the complex application of the Atomic Energy Act. In the part, comparison to the environment, there is an example of a comparison with the results of a plant in the EU. Further the report compares the advantages and disadvantages of the WWER reactors with other light water reactors. In the last part of the presentation there is a brief opinion of the author on the steps that are awaiting us in the future. First, the 'Harmonization program' of Dukovany NPP is explained, its philosophy and principles. The basic idea is to take the right steps and strategic decisions, with the vision for the operation till the year 2025 at least. There is also a list of the most important events that are planned to increase the safety. Further the report goes briefly over the current situation in the filed of nuclear energy in the period of joining the European Union and also mentions the risks that result from this process. It concludes with the prognosis for the further position of the Dukovany nuclear power plant. (author)

Meat quality of buffaloes finished in traditional or silvopastoral system in the Brazilian Eastern Amazon.

Science.gov (United States)

Joele, Maria Rsp; Lourenço, Lúcia Fh; Lourenço Júnior, José B; Araújo, Geisielly S; Budel, Juliana Cc; Garcia, Alexandre R

2017-04-01

The present study aimed to assess the physical, chemical and sensory characteristics of meat from buffaloes finished in a Traditional System (TS) or Traditional + Silvopastoral System (TSPS) with dietary supplementation. Crossbred Murrah × Mediterranean buffaloes were raised from weaning to slaughter in the TS (n = 15) or were raised in the traditional system and finished in the TSPS (n = 15). After finishing, animals were slaughtered and their carcasses refrigerated for 24 h. The right side of each half-carcass was cut between the 12th and 13th ribs and the Longissimus thoracis muscle was removed. The cranial part underwent analyses of pH, color, weight loss as a result of cooking, water holding capacity, texture and sensory characteristics, whereas the rest of the muscle underwent microbiological analyses and determination of the chemical composition, fatty acid profile and mineral content. No major difference between finishing systems was found (P > 0.05) in the physical analyses and chemical composition of meat. The percentage of myristic acid (C14:0) and the sum of polyunsaturated fatty acids differed between treatments. The TS meat had the best 'characteristic meat aroma'. Considering the quality of meat produced in the TS or TSPS, it is concluded that finishing buffaloes in the pasture still represents the best alternative. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Surface Roughness, Microhardness, and Microleakage of a Silorane-Based Composite Resin after Immediate or Delayed Finishing/Polishing

Directory of Open Access Journals (Sweden)

Fernanda Carvalho Rezende Lins

2016-01-01

Full Text Available Objective. This study evaluated the effect of immediate or delayed finishing/polishing using different systems on the surface roughness, hardness, and microleakage of a silorane-based composite. Material and Methods. Specimens were made with silorane-based composite (Filtek P90, 3M ESPE and assigned to the treatments: control (light-cured; aluminum oxide discs (Sof-Lex, 3M ESPE; diamond-impregnated silicone tips (Astropol, Ivoclar Vivadent; aluminum oxide-impregnated silicone tips (Enhance, Dentsply. Half of the specimens were finished/polished immediately and the rest after 7 days. Surface roughness (Ra, μm; n=20 and Vickers microhardness (50 g; 45 s; n=10 were measured. Cavities were prepared in bovine incisors and filled with Filtek P90. The fillings received immediate or delayed finishing/polishing (n=10 and were subjected to dye penetration test (0.5% basic fuchsin, 24 h. Data were analyzed by ANOVA and Scheffe, Kruskal-Wallis, and Mann-Whitney tests (p<0.05. Results. The finishing/polishing system significantly influenced roughness and microhardness (p<0.0001. For enamel, microleakage was not affected by the finishing/polishing system (p=0.309. For dentin, Sof-Lex discs and Astropol points promoted greater microleakage than Enhance points (p=0.033. Conclusion. Considering roughness, microhardness, and microleakage together, immediate finishing/polishing of a silorane-based composite using aluminum oxide discs may be recommended.

CSER 79-028, Addendum 2: Security bar addition to pedestal storage racks in Room 3 in 2736-Z Building

International Nuclear Information System (INIS)

Miller, E.M.

1994-01-01

The Plutonium Finishing Plant (PFP) is installing security bars on plutonium storage racks in Room 3 in 2736-Z Building to meet International Atomic Energy Agency (IAEA) material control requirements. Figures show the existing arrangement and design of the security bars. The security bars are to be fabricated of aluminum or carbon steel. The detailed fabrication sketches are reproduced in Appendix C. The security bars are to be installed close to the chains of plutonium so a determination of their effect on criticality safety needs to be made. The addition of security bars to the storage array of 2.5 kg plutonium buttons in Room 3 can effect reactivity by reflecting neutrons back into the plutonium in the storage cans, by absorbing neutrons, and by moderating neutrons between stored plutonium buttons. The small amount of metal added by the storage bars in comparison to the amount of concrete in the walls and aluminum in the shelf monitors already in place would not significantly increase the k eff of the storage array. Several computer calculations in previous analyses show that the security bars will have a negligible affect on reactivity

UPDATE HANFORD SITE D and D PROGRAMS ACCELERATE EXPAND

International Nuclear Information System (INIS)

GERBER, M.S.

2004-01-01

A large, new decontamination and decommissioning organization targeted toward rapid, focused work on aging and highly contaminated structures was formed at the DOE's Hanford Site in southeast Washington state in autumn 2003. Managed by prime contractor Fluor Hanford, the new organization has made significant progress during its first six months. Under the direction of Mike Lackey, who recently joined Fluor from the Portland General Electric Trojan Plant, the Fluor Hanford DandD organization is tackling the Plutonium Finishing Plant (PFP) complex and the Fast Flux Test Facility (FFTF), and is nearly finished demolishing the 233-S Plutonium Concentration Facility. In addition, the DandD organization is progressing through the development and public comment phases of its required environmental permitting, planning work and procurement services to DandD three other Hanford facilities: 224-T and 224-B Plutonium Concentration Facilities, and the U Plant radiochemical processing facility. It is also planning and beginning to DandD the spent fuel handling areas of the Site's 100-K Reactor Area. The 586-square mile Hanford Site, the oldest plutonium production center in the world, served as the ''workhorse'' of the American nuclear defense arsenal from 1944 through 1989. Hanford produced the special nuclear material for the plutonium cores of the Trinity (test) and Nagasaki explosions, and then went on to produce more than half of the weapons plutonium ever manufactured by the United States, and about one-fourth of that manufactured worldwide. As a result, Hanford, the top-secret ''Paul Bunyan'' in the desert, is one of the most contaminated areas in the world. Its cleanup agreement with state and federal regulators, known as the ''Tri-Party Agreement,'' celebrates its 15th anniversary this spring, at a time when operations dealing with unstable plutonium leftovers, corroded spent fuel, and liquids wastes in single-shelled tanks conclude. As these crucial jobs are coming to

Machining the Integral Impeller and Blisk of Aero-Engines: A Review of Surface Finishing and Strengthening Technologies

Science.gov (United States)

Fu, Youzhi; Gao, Hang; Wang, Xuanping; Guo, Dongming

2017-05-01

The integral impeller and blisk of an aero-engine are high performance parts with complex structure and made of difficult-to-cut materials. The blade surfaces of the integral impeller and blisk are functional surfaces for power transmission, and their surface integrity has significant effects on the aerodynamic efficiency and service life of an aero-engine. Thus, it is indispensable to finish and strengthen the blades before use. This paper presents a comprehensive literature review of studies on finishing and strengthening technologies for the impeller and blisk of aero-engines. The review includes independent and integrated finishing and strengthening technologies and discusses advanced rotational abrasive flow machining with back-pressure used for finishing the integral impeller and blisk. A brief assessment of future research problems and directions is also presented.

Resolution of USQ regarding source term in the 232-Z Waste Incinerator Building

International Nuclear Information System (INIS)

Westsik, G.A.

1995-09-01

The 232-Z Waste Incinerator at the Hanford Plutonium Finishing Plant (PFP) was used to incinerate plutonium-bearing combustible materials generated during normal plant operations. Nondestructive (NDA) measurements performed after the incinerator ceased operations indicated high plutonium loadings in exhaust ductwork near the incinerator glovebox, while the incinerator was found to have only low quantities. Measurements, following a campaign to remove some of the ductwork, resulted in markedly higher assay value for the incinerator glovebox itself. Subsequent assays confirmed the most recent results and pointed to a potential further underestimation of the holdup, in part because of attenuation due to fire brick, which could not be seen easily and which had been reported to not be present. NaI detector based measurements were used to map the deposits. Extended count times, using high resolution Ge detectors helped estimate the isotopic composition of the plutonium and quantify the deposits. Experiments were performed using a Ge detector to obtain adequate corrections for the high attenuation of the incinerator glovebox. Several neutron detectors and detector configurations were employed to understand and quantify the neutron flux. Due to the disparity that was anticipated to occur between the gamma ray and neutron assay results, radiation modeling was used to try to reconcile the divergent results. This was a third aspect of the team's effort, utilizing computer modeling to resolve discrepancies between measurement methods

Development and application of special instrumentation for materials accountancy and process control in spent fuel recycle plants

International Nuclear Information System (INIS)

Clark, P.A.; Gardner, N.; Merrill, N.H.; Whitehouse, K.R.

1996-01-01

Safe and optimum operations of spent fuel recycle plants rely on the availability of real time measurement systems at key points in the process. More than thirty types of special instrument systems have been developed and commissioned on the THORP reprocessing plant at Sellafield. These systems are compiled together with the associated information on measurement purpose, measurement technique and plant performance. A number of these measurement systems are of interest to support Safeguards arrangements on the plant. A more detailed overview of two such instrument systems respectively within the Head End and Product Finishing Stages of THORP is provided. The first of these is the Hulls Monitor, based on high resolution gamma spectrometry, as well as active and passive neutron measurements, of the basket of leached fuel cladding. This provides vital data for criticality assurance, nuclear material accountancy and inventory determination for ultimate disposal of the cladding waste. The second system is the Plutonium Inventory Monitoring System (PIMS) which employs passive neutron counting from a distributed array of neutron detectors within the Pu Finishing Line. This provides a near real time estimate of Pu inventories both during operations and at clean out of the Finishing Line. Both the Hulls Monitor and PIMS technologies are applicable to MOX Fuel recycle. Both systems enhance the control of fissile material in key areas of the recycle process which are of interest to the Safeguards authorities. (author)

Application of digital control in Japanese PWR Plants

International Nuclear Information System (INIS)

Taguchi, S.; Kondo, Y.; Teranishi, S.; Matsumiya, M.; Takashima, M.; Nagai, T.

1986-01-01

More reliable and flexible control system to improve the plant availability and operability is constantly demanded. In order to answer the demands, digital control systems are being applied to Japanese PWR plants. Microprocessor-based digital control systems are widely used in other industries and show good performance. The digital control system has been already applied to the chemical and volume control system and the radioactive waste disposal system in the operating plants. These systems have been working as expected and demonstrating good performances. The digital control system for the reactor control system, which is the main control system of the PWR plants, is being developed. The design of the system has been already finished and the verification/validation process is now in progress

The effects of stainless steel finish on Salmonella Typhimurium attachment, biofilm formation and sensitivity to chlorine.

Science.gov (United States)

Schlisselberg, Dov B; Yaron, Sima

2013-08-01

Bacterial colonization and biofilm formation on stainless steel (SS) surfaces can be sources for cross contamination in food processing facilities, possessing a great threat to public health and food quality. Here the aim was to demonstrate the influence of surface finish of AISI 316 SS on colonization, biofilm formation and susceptibility of Salmonella Typhimurium to disinfection. Initial attachment of S. Typhimurium on surfaces of SS was four times lower, when surface was polished by Bright-Alum (BA) or Electropolishing (EP), as compared to Mechanical Sanded (MS) or the untreated surface (NT). The correlation between roughness and initial bacterial attachment couldn't account on its own to explain differences seen. Biofilms with similar thickness (15-18 μm) were developed on all surfaces 1-day post inoculation, whereas EP was the least covered surface (23%). Following 5-days, biofilm thickness was lowest on EP and MS (30 μm) and highest on NT (62 μm) surfaces. An analysis of surface composition suggested a link between surface chemistry and biofilm development, where the higher concentrations of metal ions in EP and MS surfaces correlated with limited biofilm formation. Interestingly, disinfection of biofilms with chlorine was up to 130 times more effective on the EP surface (0.005% surviving) than on the other surfaces. Overall these results suggest that surface finish should be considered carefully in a food processing plant. Copyright © 2013 Elsevier Ltd. All rights reserved.

EFFECT OF ARTIFICIAL WEATHERING ON WOOD LAMINATES COLOR TREATED WITH TWO FINISHING PRODUCTS

Directory of Open Access Journals (Sweden)

Thais Jacob Mendes

2016-03-01

Full Text Available Weathering is one of the main reasons for the degradation of wood, especially its color. The application of finishes minimizes these effects. This study aimed to monitor the effect of artificial weathering on wood veneer of the species cumaru (Dipteryx odorata and pau marfim (Balfourodendron riedelianum with two finishes, the marine varnish and Cetol, with monitoring using a spectrophotometer. The samples were subjected to cycles of exposure to weathering for 20, 40, 52, 76, 124, 226, 430, 838 and 960 hours. The colorimetric parameters (L*, a*, b*, C and h* were measured before treatment, after application of the products and during the weathering time intervals. The application of finishes darkened veneer of cumaru wood and pau marfim in nature. However, in higher weathering times, both species returned to a lighter color, and even became lighter than the natural wood. The use of Cetol was more efficient, giving greater stability in the conservation of wood color of the species studied.

Effects of roughage inclusion and particle size on performance and rumination behavior of finishing beef steers

Science.gov (United States)

Roughage is mechanically processed to increase digestibility, and handling and mixing characteristics in finishing diets. Roughage is fed to promote rumen health and decrease digestive upset, but inclusion in finishing diets is limited due to the cost per unit of energy. Rumination behavior may be a...

EFEK LAMA WAKTU PEMBATASAN PEMBERIAN PAKAN TERHADAP PERFORMANS AYAM PEDAGING FINISHER

Directory of Open Access Journals (Sweden)

Muharlien Muharlien

2012-04-01

Full Text Available ABSTRAK Tujuan penelitian untuk mengetahui pengaruh lama waktu pembatasan pemberian pakan terhadap performans atau penampilan  produksi ayam pedaging periode finisher. Hasil penelitian diharapkan dapat memberikan informasi tentang lama waktu pembatasan pakan untuk mendapatkan  efisiensi penggunaan pakan kepada masyarakat khususnya peternak  ayam pedaging .. Metode penelitian mengunakan metode percobaan, dengan Rancangan Acak Lengkap (RAL dengan perlakuan : tanpa pembatasan pemberian pakan (P0, 2 jam/hari pembatasan pemberian pakan (P1, 4 jam/hari pembatasan pemberian pakan (P2 dan 6 jam/hari pembatasan pemberian pakan (P3. Setiap perlakuan diulang 6 kali. Variabel yang diamati :  konsumsi pakan, pertambahan bobot badan dan konversi pakan. Data yang diperoleh dianalisis dengan sidik ragam dan bila terdapat perbedaan  yang nyata atau sangat nyata dilanjutkan  dengan uji beda nyata jujur (BNJ. Hasil penelitian menunjukkan pembatasan waktu pemberian pakan memberikan perbedaan pengaruh yang sangat nyata (P0.05 and significant effect (P<0.05 on feed conversion. The conclution was restricted feeding a long as 6 hours/day had lowest feed conversion (1.69.  Suggested on rearing finisher broiler could be restricted feeding time 6 hours/day for feed efficiency.   Keyword: finisher broiler, feed restriction , feed consumption, body weight gain, feed conversion

THE INFLUENCE OF GLUTEN - FREE FLOURS ON THE QUALITY INDICATORS OF BISCUIT SEMI - FINISHED PRODUCTS

Directory of Open Access Journals (Sweden)

К. G. IORGACHOVA

2016-12-01

Full Text Available The article is devoted to the research of applicability of gluten-free flours from cereal crops and from by-products of cereal crop processing - ground crumbs sifted out in a process of flake production from rice, corn and millet during the production of biscuit semi-finished products. Taking into account that viscosity is an important technological characteristic of foam-like biscuit dough, as it determines foam strength and dispersed medium stability, the influence of gluten-free flours on the structural and rheological properties of biscuit dough was studied. It is determined that the substitution of wheat flour for cereal flours leads to viscosity reduction of the dough as a consequence of absence of gluten-forming proteins in them. A comparative analysis of changes in viscous properties of biscuit dough based on flour from flakes crumb while warming it up to 60°C with dough based on cereal flours and dough based on wheat flour was held. It is shown that the presence of partially gelatinized starch granules in flour from flake crumb, as a result of technological peculiarities of their extraction, promotes greater demonstration of thickening properties already at the initial stage of baking than in cereal flours. This leads to an increase of dough viscosity and formation of desired rheological characteristics, which provide the porous structure of finished products. To provide the high quality of gluten-free biscuit semi-finished products, the recipe composition of gluten-free biscuit semi-finished product, based on flour mixture from millet flakes crumb, corn and rice flour, was optimized by using the method of mathematical design of experiments.  The porosity indicator was chosen as the criteria for the evaluation of influence of proportion of gluten-free flours on the quality of biscuit semi-finished products. The response surfaces of dependency of biscuit porosity from mass ratio of recipe components in the composite mixture were

Effect of Moringa oleifera leaf meal on finisher pig growth ...

African Journals Online (AJOL)

Effect of Moringa oleifera leaf meal on finisher pig growth performance, meat ... pig growth performance, meat quality, shelf life and fatty acid composition of pork ... negative effect on feed conversion efficiency, carcass and meat quality traits, ...

Effect of finishing and polishing on the color stability of a composite resin immersed in staining solutions

Directory of Open Access Journals (Sweden)

Maiara Justo Polli

2015-01-01

Full Text Available Objective: To evaluate the influence of finishing/polishing methods and staining solutions using different immersion periods on the color stability of a microhybrid composite resin. Materials and Methods: Ninety specimens were fabricated using a stainless steel mold and polyester strips. The samples were randomly divided into five groups according to the finishing and polishing performed: Control group (no surface treatment was performed, Diamond Pro group, Diamond burs group, Enhance group, and SiC paper group. After finishing and polishing, six samples from each group were immersed in coffee, red wine, or water for 30 days. The color measurements were obtained using digital photography before immersion and after 7, 15, and 30 days of immersion. The red, green, and blue values provided by the Adobe Photoshop software were converted into CIELab values. A three-way analysis of variance and Tukey's test were used for statistical analysis (P ≤ 0.05. Results: The finishing and polishing methods, staining solutions, immersion times, and their interaction had statistically significant effects on the color change (P = 0.00. Coffee and red wine caused intense staining. Among the polishing methods, the highest color change value was observed in the control group (P < 0.05 and the Diamond Pro disks provided the most stain-resistant surfaces (P ≤ 0.05. Conclusion: The finishing and polishing method, staining solution, and immersion time influences the color stability. Finishing and polishing should be applied to obtain a more stain-resistant surface.

Lathe Attachment Finishes Inner Surface of Tubes

Science.gov (United States)

Lancki, A. J.

1982-01-01

Extremely smooth finishes are machined on inside surfaces of tubes by new attachment for a lathe. The relatively inexpensive accessory, called a "microhone," holds a honing stone against workpiece by rigid tangs instead of springs as in conventional honing tools. Inner rod permits adjustment of microhoning stone, while outer tube supports assembly. Outer tube is held between split blocks on lathe toolpost. Microhoning can be done with either microhone or workpiece moving and other member stationary.

Influence of Rapeseed Meal on Growth Performance, Blood Profiles, Nutrient Digestibility and Economic Benefit of Growing-finishing Pigs

Directory of Open Access Journals (Sweden)

H. B. Choi

2015-09-01

Full Text Available This study was conducted to investigate the influence of dietary rapeseed meal (RSM on growth performance, blood profiles, nutrient digestibility and economic benefit of growing-finishing pigs. A total of 120 growing pigs ([Yorkshire×Landrace] ×Duroc with an initial body weight (BW 29.94±0.06 kg were used in this experiment. Pigs were randomly allotted into 1 of 5 treatments in a randomized complete block design and 6 replicates with 4 pigs per pen. Treatments were divided by dietary RSM supplementation levels (0%, 3%, 6%, 9%, or 12% in growing-finishing diets. A linear decrease (p<0.05 of BW and average daily gain (ADG were observed at 13th wk of finishing and overall periods of pigs. Additionally, gain-to-feed ratio (G/F tended to decrease by dietary RSM supplementation in growing-finishing diets (linear, p = 0.07 and quadratic, p = 0.08. Concentrations of serum triiodothyronine and thyroxine were not influenced by dietary RSM treatments whereas thyroid gland and liver weight were increased at 13th wk of finishing period (linear, p<0.05; p<0.01 by increasing dietary RSM supplementation level. In blood profiles, serum total cholesterol and low density lipoprotein cholesterol concentrations were not differed by dietary treatments at 13th wk of finishing period whereas concentration of serum high density lipoprotein cholesterol was affected by the supplementation level of RSM, resulting in a linear RSM level responses (p<0.05. Serum blood urea nitrogen concentration tended to decrease (linear, p = 0.07; p = 0.08 at 6th wk of growing and 13th wk of finishing periods and digestibility of dry matter tended to decrease by dietary RSM (linear, p = 0.09. Crude protein, crude fat and nitrogen retention, whereas, were not affected by dietary RSM supplementation level. In the economic analysis, feed cost per weight gain was numerically decreased when RSM was provided up to 9%. Consequently, RSM could be supplemented to growing-finishing diets up to 9

Marketing Strategy Formulation for the Introduction of Eukula Strato German Wood Finishes in Local Market of Emerging Indian Economy

Directory of Open Access Journals (Sweden)

Suraj Kushe Shekhar

2013-09-01

Full Text Available Wood finishing relates to the process of embellishing or protecting the surface of the wood. The paper aimed at formulating a marketing strategy for introducing water borne German based Wood Finishes named Eukula Strato into local market of northern Kerala, India. Multiple cross sectional descriptive research with judgmental sampling technique elicited responses from Finishers, Furniture manufacturers and Interior designers. Findings revealed that Eukula Strato had a distinct advantage when compared to any other Wood Finish that was available in the local market. Findings and suggestions were reported as per 4P’s of marketing mix. Percentage analysis, Chi square analysis etc were used to interpret the results

Wavelet theory and belt finishing process, influence of wavelet shape on the surface roughness parameter values

International Nuclear Information System (INIS)

Khawaja, Z; Mazeran, P-E; Bigerelle, M; Guillemot, G; Mansori, M El

2011-01-01

This article presents a multi-scale theory based on wavelet decomposition to characterize the evolution of roughness in relation with a finishing process or an observed surface property. To verify this approach in production conditions, analyses were developed for the finishing process of the hardened steel by abrasive belts. These conditions are described by seven parameters considered in the Tagushi experimental design. The main objective of this work is to identify the most relevant roughness parameter and characteristic length allowing to assess the influence of finishing process, and to test the relevance of the measurement scale. Results show that wavelet approach allows finding this scale.

A survey of grass-finished beef producers in Pennsylvania

Science.gov (United States)

To meet our goal of quantifying the environmental impacts of grass-finished beef production, data on production practices in Pennsylvania were collected at the farm level via visits and online surveys. Twenty-three responses represented a total of 1,055 animals on 2,155 acres of land. Farms were rel...

Influence of the quality of the finished occlusion on postretention occlusal relapse.

Science.gov (United States)

de Freitas, Karina Maria Salvatore; Janson, Guilherme; de Freitas, Marcos Roberto; Pinzan, Arnaldo; Henriques, José Fernando Castanha; Pinzan-Vercelino, Célia Regina Maio

2007-10-01

In this study, we aimed to evaluate the influence of the quality of the finished occlusion on postretention occlusal stability. The sample comprised 87 patients with Class I malocclusion, treated with extraction of the 4 first premolars and edgewise mechanics; they were divided into 2 groups, according to the quality of their finished occlusions. Group 1 included 44 subjects (23 boys, 21 girls) with posttreatment peer assessment rating (PAR) scores from 0 to 5. The mean pretreatment age was 13.74 years (SD 2.14). The mean treatment time was 1.92 years (SD 0.57), the mean retention time was 1.75 years (SD 0.96), and the mean time of posttreatment evaluation was 5.17 years (SD 1.82). Group 2 included 43 subjects (22 boys, 21 girls) with posttreatment PAR scores greater than 5. The mean initial age was 13.34 years (SD 1.35). The mean treatment time was 2.20 years (SD 0.66), the mean retention time was 1.77 years (SD 0.78), and the mean posttreatment evaluation was 5.47 years (SD 1.60). The PAR and the Little irregularity indexes were measured on the dental casts at pretreatment, posttreatment, and postretention. Intergroup comparisons were made with independent t tests, and the Pearson correlation coefficient was applied to the PAR score for the whole sample at the times evaluated. Well-finished patients had lower posttreatment and postretention PAR scores and greater changes during the treatment and posttreatment periods than did the poorly finished patients. For the Little irregularity index, the only difference between the groups was at the posttreatment stage; group 1 had a smaller irregularity score than group 2. The correlation coefficients showed that the greater the treatment changes, the smaller the posttreatment PAR score and the greater the relapse. But the higher the posttreatment PAR score, the higher the postretention PAR score. It was concluded that the greater the quality of the orthodontic finished occlusion, the greater are the treatment changes and

A Case Study into Microbial Genome Assembly Gap Sequences and Finishing Strategies.

Science.gov (United States)

Utturkar, Sagar M; Klingeman, Dawn M; Hurt, Richard A; Brown, Steven D

2017-01-01

This study characterized regions of DNA which remained unassembled by either PacBio and Illumina sequencing technologies for seven bacterial genomes. Two genomes were manually finished using bioinformatics and PCR/Sanger sequencing approaches and regions not assembled by automated software were analyzed. Gaps present within Illumina assemblies mostly correspond to repetitive DNA regions such as multiple rRNA operon sequences. PacBio gap sequences were evaluated for several properties such as GC content, read coverage, gap length, ability to form strong secondary structures, and corresponding annotations. Our hypothesis that strong secondary DNA structures blocked DNA polymerases and contributed to gap sequences was not accepted. PacBio assemblies had few limitations overall and gaps were explained as cumulative effect of lower than average sequence coverage and repetitive sequences at contig termini. An important aspect of the present study is the compilation of biological features that interfered with assembly and included active transposons, multiple plasmid sequences, phage DNA integration, and large sequence duplication. Our targeted genome finishing approach and systematic evaluation of the unassembled DNA will be useful for others looking to close, finish, and polish microbial genome sequences.

Choice of crystal surface finishing for a dual-ended readout depth-of-interaction (DOI) detector

International Nuclear Information System (INIS)

Fan, Peng; Ma, Tianyu; Liu, Yaqiang; Wang, Shi; Wei, Qingyang; Yao, Rutao

2016-01-01

The objective of this study was to choose the crystal surface finishing for a dual-ended readout (DER) DOI detector. Through Monte Carlo simulations and experimental studies, we evaluated 4 crystal surface finishing options as combinations of crystal surface polishing (diffuse or specular) and reflector (diffuse or specular) options on a DER detector. We also tested one linear and one logarithm DOI calculation algorithm. The figures of merit used were DOI resolution, DOI positioning error, and energy resolution. Both the simulation and experimental results show that (1) choosing a diffuse type in either surface polishing or reflector would improve DOI resolution but degrade energy resolution; (2) crystal surface finishing with a diffuse polishing combined with a specular reflector appears a favorable candidate with a good balance of DOI and energy resolution; and (3) the linear and logarithm DOI calculation algorithms show overall comparable DOI error, and the linear algorithm was better for photon interactions near the ends of the crystal while the logarithm algorithm was better near the center. These results provide useful guidance in DER DOI detector design in choosing the crystal surface finishing and DOI calculation methods. (paper)

Management Characteristics of Grass-finished Beef Operations in the Northeast

Science.gov (United States)

An online survey of self-identified grass-finished beef producers was conducted throughout the Northeast region along with several farm visits. Seventy acceptable records from producers in Delaware, Maine, Massachusetts, Maryland, New Hampshire, New Jersey, New York, Pennsylvania, Vermont, and West ...

Multi-Parameter Analysis of Surface Finish in Electro-Discharge Machining of Tool Steels

Directory of Open Access Journals (Sweden)

Cornelia Victoria Anghel

2006-10-01

Full Text Available The paper presents a multi- parameter analysis of surface finish imparted to tool-steel plates by electro-discharge machining (EDM is presented. The interrelationship between surface texture parameters and process parameters is emphasized. An increased number of parameters is studied including amplitude, spacing, hybrid and fractal parameters,, as well. The correlation of these parameters with the machining conditions is investigated. Observed characteristics become more pronounced, when intensifying machining conditions. Close correlation exists between certain surface finish parameters and EDM input variables and single and multiple statistical regression models are developed.

Hybrid machining processes perspectives on machining and finishing

CERN Document Server

Gupta, Kapil; Laubscher, R F

2016-01-01

This book describes various hybrid machining and finishing processes. It gives a critical review of the past work based on them as well as the current trends and research directions. For each hybrid machining process presented, the authors list the method of material removal, machining system, process variables and applications. This book provides a deep understanding of the need, application and mechanism of hybrid machining processes.

Serum biochemical indices of Finisher Broiler Chickens fed diets ...

African Journals Online (AJOL)

A 4 week feeding trial was conducted using 180 five-week old Hubbard broiler chickens to determine the effect of feeding variously processed roselle(Hibiscus sabdariffa) seeds on serum biochemical indices with a view to determining the potential of roselle seed as an alternative to soybeans. Five broiler finisher diets were ...

Performance Of Growing Pigs And Finisher Broilers Housed Together

African Journals Online (AJOL)

Growth performance and cost of feeding young growing pigs and finisher broilers under integrated broiler/pig production system were investigated. Four young growing pigs (the control) were housed in pen A and fed 4% of their body weight as commercial growers feed. Another 4 were housed in pen B with broilers in ...

Response of finishing broiler chickens to diets containing rumen ...

African Journals Online (AJOL)

One hundred and fifty Arbor acres broiler chickens aged four weeks were used in determining the effect of fermented rice husk meal diets on the performance and nutrient digestibility of finisher broiler chickens. They were allotted into five dietary treatments containing 0, 5, 10, 15 and 20 % rumen liquor fermented rice husk ...

The association between disease and profitability in individual finishing boars at a test station

DEFF Research Database (Denmark)

Jensen, Tina Birk; Baadsgaard, Niels Peter; Houe, Hans

2008-01-01

Endemic diseases in finisher herds are considered to be costly for the pig producer. We investigated the effect of diseases on the profit margin using data from a Danish boar test station (n = 5777) collected from July 2002 to December 2004. Boars reaching a target slaughter weight of at least 80...... kg were included in the study. Oral and parenteral treatments were used as indicator of disease in the finishing period and, pathological lesions were used as indicator of disease at slaughter. Profit margin was calculated individually for each boar as the difference between the total revenue......: profit margin. The results showed that treatment in the finishing period had a negative effect on the profit margin. According to the least square means estimates, boars that were treated parenterally had a reduction in the profit margin of 2.24 €. This corresponded to a reduction in the profit margin...

Implementation of Lean Warehouse to Minimize Wastes in Finished Goods Warehouse of PT Charoen Pokphand Indonesia Semarang

Directory of Open Access Journals (Sweden)

Nia Budi Puspitasari

2016-03-01

Full Text Available PT. Charoen Pokphand Indonesia Semarang is one of the largest poultry feed companies in Indonesia. To store the finished products that are ready to be distributed, it needs a finished goods warehouse. To minimize the wastes that occur in the process of warehousing the finished goods, the implementation of lean warehouse is required. The core process of finished goods warehouse is the process of putting bag that has been through the process of pallets packing, and then transporting the pallets contained bags of feed at finished goods warehouses and the process of unloading food from the finished goods warehouse to the distribution truck. With the implementation of the lean warehouse, we can know whether the activities are value added or not, to be identified later which type of waste happened. Opinions of stakeholders regarding the waste that must be eliminated first need to be determined by questionnaires. Based on the results of the questionnaires, three top wastes are selected to be identified the cause by using fishbone diagram. They can be repaired by using the implementation of 5S, namely Seiri, Seiton, Seiso, Seiketsu, and Shitsuke. Defect waste can be minimized by selecting pallet, putting sack correctly, forklift line clearance, applying working procedures, and creating cleaning schedule. Next, overprocessing waste is minimized by removing unnecessary items, putting based on the date of manufacture, and manufacture of feed plan. Inventory waste is minimized by removing junks, putting feed based on the expired date, and cleaning the barn

Fundamentals of figure control and fracture-'free' finishing for high aspect ratio laser optics

Energy Technology Data Exchange (ETDEWEB)

Suratwala, Tayyab [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2014-10-01

The high level objectives of the this work were to: 1) scientifically understand critical phenomena affecting the surface figure during full aperture finishing; 2) utilize these fundamentals to more deterministically control the surface figure during finishing; 3) successfully polish under rogue particle-‘free’ environments during polishing by understanding/preventing key sources of rogue particles.

Effect of Moringa oleifera leaf meal on finisher pig growth ...

African Journals Online (AJOL)

Felistus

2014-12-12

Dec 12, 2014 ... (FCR) of finisher pigs, physico-chemical meat quality, fatty acid (FA) composition and shelf life of pork was .... 5.2 mg manganese; 2.6 mg copper; 0.05 mg selenium. ... indicating redness (red-green spectrum) and b*, indicating ...

78 FR 23591 - Certain Prepregs, Laminates, and Finished Circuit Boards

Science.gov (United States)

2013-04-19

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-659 (Enforcement)] Certain Prepregs... United States after importation of certain prepregs, laminates, and finished circuit boards that infringe... prepregs and laminates that are the subject of the investigation or that otherwise infringe, induce, and/or...

77 FR 2031 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

Science.gov (United States)

2012-01-13

... Parts Thereof, Finished and Unfinished From the People's Republic of China: Extension of the Time Limit..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW..., finished and unfinished from the People's Republic of China. See Tapered Roller Bearings and Parts Thereof...

An Overview of Surface Finishes and Their Role in Printed Circuit Board Solderability and Solder Joint Performance

Energy Technology Data Exchange (ETDEWEB)

Vianco, P.T.

1998-10-15

A overview has been presented on the topic of alternative surface finishes for package I/Os and circuit board features. Aspects of processability and solder joint reliability were described for the following coatings: baseline hot-dipped, plated, and plated-and-fused 100Sn and Sn-Pb coatings; Ni/Au; Pd, Ni/Pd, and Ni/Pd/Au finishes; and the recently marketed immersion Ag coatings. The Ni/Au coatings appear to provide the all-around best option in terms of solderability protection and wire bondability. Nickel/Pal ftishes offer a slightly reduced level of performance in these areas that is most likely due to variable Pd surface conditions. It is necessmy to minimize dissolved Au or Pd contents in the solder material to prevent solder joint embrittlement. Ancillary aspects that included thickness measurement techniques; the importance of finish compatibility with conformal coatings and conductive adhesives; and the need for alternative finishes for the processing of non-Pb bearing solders were discussed.

Cs-137 and Co-60 concentrations in water from the Savannah River and water-treatment plants downstream of SRP

International Nuclear Information System (INIS)

1983-01-01

In preparation for restart of L-Reactor, a comprehensive environmental sampling and analysis program was initiated in March 1983 to determine Cs-137 concentrations in off-site water downstream from Savannah River Plant (SRP). Concentrations of Co-60 also are determined in this sampling and analysis program. This report summarizes the first three months of results. Cesium-137 concentrations are reported for finished water from the Beaufort-Jasper, Port Wentworth and North Augusta water treatment plants for weekly continuous samples during April through June 1983. The very low concentrations of cesium-137 in finished water from downstream water treatment plants showed significant changes during this time. The changes in concentration occurred smoothly and correlate with changes in river flow. No changes in concentration during April through June can be attributed to L-Reactor's only cold water test which occurred June 8 and 9. No Co-60 was observed in any samples

Effect of Various Finishing Procedures on the Reflectivity (Shine) of Tooth Enamel - An In-vitro Study.

Science.gov (United States)

Patil, Harshal Ashok; Chitko, Shrikant Shrinivas; Kerudi, Veerendra Virupaxappa; Maheshwari, Amit Ratanlal; Patil, Neeraj Suresh; Tekale, Pawankumar Dnyandeo; Gore, Ketan Ashorao; Zope, Amit Ashok

2016-08-01

Reflectivity of an object is a good parameter for surface finish. As the patient evaluates finishing as a function of gloss/reflectivity/shine an attempt is made here to evaluate changes in surface finish with custom made reflectometer. The aim of the present study was to study the effect of various procedures during orthodontic treatment on the shine of enamel, using a custom made reflectometer. Sixty one extracted premolars were collected and each tooth was mounted on acrylic block. Reflectivity of the teeth was measured as compared to standard before any procedure. One tooth was kept as standard throughout the study. Sixty teeth were acid etched. Reflectivity was measured on custom made reflectometer and readings recorded. Same procedure was repeated after debonding. Then 60 samples were divided into three groups: Group 1 - Tungsten Carbide, Group 2 - Astropol, Group 3- Sof-Lex disc depending upon the finishing method after debonding and reflectivity was measured. The mean percentage of reflectivity after acid etching was 31.4%, debonding 45.5%, Tungsten carbide bur finishing (Group 1) was 58.3%, Astropol (Group 2) 72.8%, and Sof-Lex disc (Group 3) 84.4% as that to the standard. There was statistically very highly significant (p Group 2> Group 1. The primary goal was to restore the enamel to its original state after orthodontic treatment. The methods tested in this study could not restore the original enamel reflectivity.

Carpentry and Finishing Procedures. Building Maintenance. Module II. Instructor's Guide.

Science.gov (United States)

Hawk, Sam; Brunk, Art

This curriculum guide, keyed to the building maintenance competency profile developed by industry and education professionals, provides three units on carpentry and finishing procedures. The first unit, Exterior Carpentry, contains the following lessons: carpentry safety procedures, ladder and scaffolding safety, door installation/repair,…

Fungal biodegradation of plantain peel for broiler finisher feeding: In ...

African Journals Online (AJOL)

... protein, cholesterol and glucose were significantly (P<0.05) affected by the treatments. Fungal biodegradation of PPL using A.niger has the potential of enhancing feed intake, nutrient digestibility and the body weight gain of broiler finisher. Keywords: Aspergillus niger, biodegradation, nutrient enhancement and broilers.

Effects of surface finish and mechanical training on Ni-Ti sheets for elastocaloric cooling

Directory of Open Access Journals (Sweden)

Kurt Engelbrecht

2016-06-01

Full Text Available Elastocaloric cooling has emerged as a promising alternative to vapor compression in recent years. Although the technology has the potential to be more efficient than current technologies, there are many technical challenges that must be overcome to realize devices with high performance and acceptable durability. We study the effects of surface finish and training techniques on dog bone shaped polycrystalline samples of NiTi. The fatigue life of several samples with four different surface finishes was measured and it was shown that a smooth surface, especially at the edges, greatly improved fatigue life. The effects of training both on the structure of the materials and the thermal response to an applied strain was studied. The load profile for the first few cycles was shown to change the thermal response to strain, the structure of the material at failure while the final structure of the material was weakly influenced by the surface finish.

Effect of finishing system on carcass characteristics and composition ...

African Journals Online (AJOL)

Effect of finishing system on carcass characteristics and composition of Mubende goats and their Boer goat crossbreds. ... Dissectible lean and fat percentages varied in an ascending order of 66%, 72%, 72.6% and 8%, 14% and 16.5% for T1, T2 and T3, respectively. A reverse trend was observed for bone percentages with ...

Digital Restoration from Start to Finish How to repair old and damaged photographs

CERN Document Server

Ctein,

2010-01-01

Digital Restoration: Start to Finish 2nd edition guides you step-by-step through the entire process of restoring old photographs and repairing new ones using Adobe Photoshop, Picture Window, and now Elements. Nothing is left out, from choosing the right hardware and software and getting the photographs into the computer, to getting the finished photo out of the computer and preserving it for posterity.  LEARN HOW TO: Scan faded and damaged prints or films Improve snapshots with Shadow/Highlight adjustment Correct uneven exposure Fix color and skin tones quickly with Curves, plug-ins, a

PCBs with immersion tin finish - some experiences with lead-free reflow process

Energy Technology Data Exchange (ETDEWEB)

Bukat, K.; Koziol, G.; Sitek, J.; Borecki, J.; Hackiewicz, H. [Tele and Radio Research Inst., Warsaw (Poland); Merkle, H.; Schroeder, S. [Ormecon Chemie GmbH and Co. KG, Ammersbek (Germany); Girulska, A.; Gardela, K. [Eldos Sp. z o.o., Wroclaw (Poland)

2004-07-01

Substitution of lead-free solders in electronic assemblies requires changes in the conventional SnPb finishes of PCBs. The Craft project ''PRINT'' objectives respond to this challenge. Its main goal is to develop and implement the new technology of high solderability immersion tin for printed circuit boards at small and medium enterprises. The subject of the research was organic based immersion tin coating which would fulfil demands of SMT. In the paper the results of reflow soldering process on PCBs covered by Ormecon registered immersion tin finish with using lead-free solder pastes will be described. Solderability of tin coating as well as wettability of lead-free solder paste will be presented. (orig.)

POTENTIAL USE OF COLLAGEN HYDROLYSATES FROM CHAMOIS LEATHER WASTE AS INGREDIENT IN LEATHER FINISHING FORMULATIONS

Directory of Open Access Journals (Sweden)

POPA Emil

2016-05-01

Full Text Available The aim of this paper is the obtaining of value-added products from the dust resulted from chamois leather buffering, a solid waste that raises serious disposal problems, due to its physical state and complex chemical composition. Starting from leather waste, an alkaline hydrolysis was performed followed by the chemical modification of the polypeptyde hydrolysate by polycondensation with dispersions of copolymers of vinyl acetate with acrylic esters and reticulation with glutaraldehyde in order to improve its hydrophobicity. The resulted product can be used/was tested as an ingredient in leather finishing formulations, as binder or carrier agent. In this paper, new finishing mixtures were prepared using pigments and obtained polypeptide hydrolysates as a substitute for casein in pigment pastes. By this method, there were obtained two experimental variants of brown and black pigment pastes which were compared to the pigment pastes with casein binder. Natural grain Box bovine leather samples coated with such admixtures were subjected to physico-mechanical resistance tests, in accordance with the standardized methods. Specific tests carried on finished leather – tensile strength, tear resistance, resistance to grain cracking, dry and wet rubbing fastness, flexural fatigue strength test, etc – showed values of this characteristics comparable to those obtained with casein conventional finishing.

[Comparative study of microleakage by using different finished lines in selective laser melting metal crowns].

Science.gov (United States)

Peng, Yan; Zhong, Qun; Wu, Xue-Ying; Weng, Jia-Wei

2016-12-01

To evaluate microleakage of SLM Co -Cr alloy metal crown with two types finished line (chamfer and shoulder), compared with conventional fabrication of Co -Cr alloy metal crowns. Thirty healthy non-carious human molars were selected and randomly assigned to 3 groups, 10 in each. Teeth in group A and C received a chamfer finish line preparation, whereas teeth in group C received a shoulder finish line. Conventional Co -Cr alloy metal crowns were fabricated for group A when SLM metal crowns were made for group B and group C. Glass ionomer was applied for bonding. After 5000 thermocycles ranging from 5degrees centigrade to 55degrees centigrade,all the specimens were evaluated by dye penetration and then microleakage was examined under light microscope. The data were analyzed statistically with SPSS 20.0 software package. Microleakage in group A was significantly higher than the other two groups, group B and group C showed no significant difference in microleakage while microleakage in group B was higher than that in group C. Microleakage of SLM metal crowns was significantly less than that of conventional Co-Cr alloy metal crowns; chamfer finish line designs was recommended for SLM metal crowns in consideration of reducing microleakage and protecting tooth.

Additive manufacturing of reflective optics: evaluating finishing methods

Science.gov (United States)

Leuteritz, G.; Lachmayer, R.

2018-02-01

Individually shaped light distributions become more and more important in lighting technologies and thus the importance of additively manufactured reflectors increases significantly. The vast field of applications ranges from automotive lighting to medical imaging and bolsters the statement. However, the surfaces of additively manufactured reflectors suffer from insufficient optical properties even when manufactured using optimized process parameters for the Selective Laser Melting (SLM) process. Therefore post-process treatments of reflectors are necessary in order to further enhance their optical quality. This work concentrates on the effectiveness of post-process procedures for reflective optics. Based on already optimized aluminum reflectors, which are manufactured with a SLM machine, the parts are differently machined after the SLM process. Selected finishing methods like laser polishing, sputtering or sand blasting are applied and their effects quantified and compared. The post-process procedures are investigated on their impact on surface roughness and reflectance as well as geometrical precision. For each finishing method a demonstrator will be created and compared to a fully milled sample and among themselves. Ultimately, guidelines are developed in order to figure out the optimal treatment of additively manufactured reflectors regarding their optical and geometrical properties. Simulations of the light distributions will be validated with the developed demonstrators.

Heterosis for meat quality and fatty acid profiles in crosses among Bos indicus and Bos taurus finished on pasture or grain.

Science.gov (United States)

Gama, L T; Bressan, M C; Rodrigues, E C; Rossato, L V; Moreira, O C; Alves, S P; Bessa, R J B

2013-01-01

Physicochemical properties and fatty acid profiles of meat from Bos indicus, Bos taurus and crossbred B. taurus×B. indicus bullocks (n=216), finished on pasture or grain, were used to estimate the effects of heterosis. Meat quality and fatty acid profiles generally benefited with crossbreeding, but the advantages from heterosis differed among finishing systems. The Warner-Bratzler shear-force in fresh and aged meat was reduced due to heterosis in pasture-finishing, but the effect was minor under grain-finishing. With pasture-finishing, heterosis caused an increase of 5% in CLA concentration, but few other changes in fatty acid profiles. In grain-finishing, heterosis caused a reduction in intramuscular fat and cholesterol, increased amounts of PUFA, n-6 fatty acids and PUFA/SFA ratio, and a decline in atherogenic index. The Δ(9) desaturase estimated activity in crossbreds showed a behavior close to B. indicus, suggesting the existence of few loci and a dominance genetic effect on enzymes involved in fatty acid synthesis and metabolism. Copyright © 2012 Elsevier Ltd. All rights reserved.

Relevance of microbial finished product testing in food safety management

NARCIS (Netherlands)

Zwietering, M.H.; Jacxsens, L.; Membre, J.M.; Nauta, M.; Peterz, M.

2016-01-01

Management of microbiological food safety is largely based on good design of processes, products and procedures. Finished product testing may be considered as a control measure at the end of the production process. However, testing gives only very limited information on the safety status of a food.

The association between measurements of antimicrobial use and resistance in the faeces microbiota of finisher batches.

Science.gov (United States)

Andersen, V D; DE Knegt, L V; Munk, P; Jensen, M S; Agersø, Y; Aarestrup, F M; Vigre, H

2017-10-01

The objectives were to present three approaches for calculating antimicrobial (AM) use in pigs that take into account the rearing period and rearing site, and to study the association between these measurements and phenotypical resistance and abundance of resistance genes in faeces samples from 10 finisher batches. The AM use was calculated relative to the rearing period of the batches as (i) 'Finisher Unit Exposure' at unit level, (ii) 'Lifetime Exposure' at batch level and (iii) 'Herd Exposure' at herd level. A significant effect on the occurrence of tetracycline resistance measured by cultivation was identified for Lifetime Exposure for the AM class: tetracycline. Furthermore, for Lifetime Exposure for the AM classes: macrolide, broad-spectrum penicillin, sulfonamide and tetracycline use as well as Herd Unit Exposure for the AM classes: aminoglycoside, lincosamide and tetracycline use, a significant effect was observed on the occurrence of genes coding for the AM resistance classes: aminoglycoside, lincosamide, macrolide, β-lactam, sulfonamide and tetracycline. No effect was observed for Finisher Unit Exposure. Overall, the study shows that Lifetime Exposure is an efficient measurement of AM use in finisher batches, and has a significant effect on the occurrence of resistance, measured either by cultivation or metagenomics.

Surface roughness and hardness of a composite resin: influence of finishing and polishing and immersion methods

Directory of Open Access Journals (Sweden)

Ana Luísa Botta Martins de Oliveira

2010-09-01

Full Text Available This study evaluated the finishing and polishing effect on the surface roughness and hardness of the Filtek Supreme XT, in fluoride solutions. Specimens were prepared (n = 140 with half of the samples finished and polished with Super-Snap® disks. The experimental groups were divided according to the presence or absence of finishing and polishing and immersion solutions (artificial saliva, sodium fluoride solution at 0.05% - manipulated, Fluordent Reach, Oral B, Fluorgard. The specimens remained immersed in artificial saliva for 24 hours and were then subjected to initial analysis (baseline of surface roughness and Vickers microhardness. Next, they were immersed in different fluoride solutions for 1 min/day, for 60 days. Afterwards, a new surface roughness and microhardness reading was conducted. The data were submitted to a two-way ANOVA and Tukey's test (5% significance level. For the comparison of mean roughness and hardness at baseline and after 60 days, the paired Student t test was used. The results showed that the surface roughness and microhardness of the Filtek Supreme XT were influenced by the finishing and polishing procedure, independently of the immersion methods.

Long-term preventive maintenance of instrumentation control equipment for PWR plants

International Nuclear Information System (INIS)

Sugitani, S.; Nanba, M.

2006-01-01

Since the PWR plants in Japan have been operated more than 30 years, main instrumentation control equipment of analog systems has been renewed to digital control systems. Renewal works had to be done in short period within periodical inspection term and for several facilities. The Mitsubishi LTD group had been provided with these market needs by its digital control system (MELTAC-NplusR 3) applicable to main instrumentation control equipment for primary and secondary systems and had already finished the renewal for practical plants. (T. Tanaka)

The Affordable Pre-Finishing of Silicon Carbide for Optical Applications, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Creare proposes to develop a novel, laser-assisted, pre-finishing process for chemical vapor deposition (CVD) coated silicon-carbide ceramics. Our innovation will...

Response of finishing broiler chickens fed three energy/protein ...

African Journals Online (AJOL)

A feeding experiment was conducted to investigate the response of finishing broiler chicken to diets containing three metabolizable energy (ME)/crude protein (CP) combinations ( 3203.76 ME vs 19.90 %CP, 2884.15 ME vs 18.10%CP and 2566.42 ME vs 18.10 %CP) at fixed ME:CP ratio of 160:1. A total of 126 four weeks ...

Effect of finishing and polishing on color stability of a nanofilled resin immersed in different media

Directory of Open Access Journals (Sweden)

Ana Luísa Botta Martins de OLIVEIRA

Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effect of finishing and polishing on color stability of a nanofilled composite resin (Filtek Z350 XT according to different immersion media.MATERIAL AND METHOD: Composite disks (10 mm diameter, 2 mm thickness were prepared for each group (n = 6 using a stainless steel mold. The groups were divided according to the presence or absence of finishing and polishing procedure and immersion media (artificial saliva, artificial juice- KAPO(r Coca-Cola(rflavors: pineapple, orange, strawberry and grape. The finishing and polishing procedures were performed using Super -Snap(r disks. The specimens were stored in artificial saliva for 24 hours (baseline and were analyzed using a color spectrophotometer by CIELab system. Then, they were immersed in different media for 5 minutes, 3 times a day, every 4 hours during 60 days. They were stored in artificial saliva at 37 ± 1°C during the immersion intervals. After this time, new measure of color was performed. The data were analyzed using Kruskall-Wallis test and Mann- Whitney test. The significance level was 5%.RESULT: The results showed that the finishing/polishing not significantly influence the color stability of resin composite (p > 0.05. There was no statistically significant difference in the color stability of the studied resin after immersion in different media (p > 0.05.CONCLUSION: The finishing and polishing procedures and the immersion media did not have influence on color stability of nanofilled resin Filtek Z350 XT.

Feed efficiency differences and reranking in beef steers fed grower and finisher diets.

Science.gov (United States)

Durunna, O N; Mujibi, F D N; Goonewardene, L; Okine, E K; Basarab, J A; Wang, Z; Moore, S S

2011-01-01

This 3-yr study used 490 steers to determine whether feedlot steers changed their feed efficiency (FE) ranking when fed a grower diet, then a finisher diet. The steers were crossbreds and were between 5 to 7 mo of age. There were 2 feeding periods each year. Within each year, approximately 90 steers had their diet switched from a grower to a finisher diet (feed-swap group), whereas another 90 steers were fed either the grower (grower-fed group) or the finisher (finisher-fed group) diet throughout the feeding trial. Each feeding test lasted for a minimum of 10 wk, and all steers were fed ad libitum. Individual animal feed intakes were collected using the GrowSafe feeding system, and BW were measured every 2 wk. Residual feed intake (RFI), G:F, and Kleiber ratio (KR) were computed at the end of each feeding period. For each measure of efficiency, animals were classified as low, medium, or high based on 0.5 SD from the mean. The majority of steers did not maintain the previous efficiency class in the second period. Approximately 58, 51, and 51% of steers in the feed-swap group, finisher-fed group, and the grower-fed group, respectively, changed their RFI measure by 0.5 SD. A low rank correlation occurred in all test groups but was less in the feed-swap group. Spearman rank correlations between the 2 feeding periods in the feed-swap group were 0.33, 0.20, and 0.31 for RFI, G:F, and KR, respectively. Classifications based on G:F and KR showed that a greater number of steers (P 0.05) between the proportions of individuals that changed or maintained their FE class. In the groups without a feed-swap, there was no difference (P > 0.05) in the proportion of steers that changed or maintained the same FE class for all FE measures. Our results suggest that diet type and feeding period affect the FE ranking in beef steers. A feedlot diet is ideal for evaluating the FE potential of steers for feedlot profitability; however, we suggest that tests involving less dense diets should

Pengaruh Berbagai Jenis Bahan Litter terhadap Kualitas Litter Broiler Fase Finisher di Closed House

OpenAIRE

Tiwi Metasari; Dian Septinova; Veronica Wanniatie

2014-01-01

The aim of this research was to 1) determine the effect of the use of rice husk, wood shavings,rice straw as litter material on litter quality for broiler during the finisher phase in closed house, 2)determine the best type of litter material on litter quality for broiler during the finisher phase in closedhouse. The duration of the research was 26 days. The research was started from 15 April to 10 May2014 in the closed house owned by PT. Rama Jaya Lampung Krawang Sari Village, the District o...

Effects of surface finish and mechanical training on Ni-Ti sheets for elastocaloric cooling

DEFF Research Database (Denmark)

Engelbrecht, Kurt; Tusek, Jaka; Sanna, Simone

2016-01-01

Elastocaloric cooling has emerged as a promising alternative to vapor compression in recent years. Although the technology has the potential to be more efficient than current technologies, there are many technical challenges that must be overcome to realize devices with high performance...... and acceptable durability. We study the effects of surface finish and training techniques on dog bone shaped polycrystalline samples of NiTi. The fatigue life of several samples with four different surface finishes was measured and it was shown that a smooth surface, especially at the edges, greatly improved...

Effects of surface-finishing protocols on the roughness, color change, and translucency of different ceramic systems.

Science.gov (United States)

Akar, Gülcan Coşkun; Pekkan, Gürel; Çal, Ebru; Eskitaşçıoğlu, Gürcan; Özcan, Mutlu

2014-08-01

Surface-finishing protocols have a mechanical impact on ceramic surfaces that could eventually affect surface topography and light scattering. An optimum protocol is needed to avoid damaging the optical properties of ceramics. The purpose of this study was to determine the effects of different surface-finishing protocols on the surface roughness, color change, and translucency of ceramic and metal ceramic restorations. Standardized disk-shaped specimens (1.5 × 10 mm, n=128) were fabricated from 3 different ceramic core materials (aluminum oxide [Al2O3]-AL, zirconium oxide [ZrO2]-ZR, lithium disilicate [Li2Si2O5]-LIT), veneered (V) with dentin ceramics (n=32 per group), and placed in the following groups: ALV, ZRV, and LITV. The metal ceramic group acted as the control (n=32). Four different surface-finishing methods were tested. Airborne-particle abrasion with 50 μm Al2O3, polishing with adjustment kit, polishing with adjustment kit plus diamond polishing paste, and autoglazing (n=8 subgroup) were applied on the veneering ceramics. The specimens were analyzed with a profilometer for surface roughness, and color change and translucency were measured with a clinical spectrophotometer. Statistical analyses were performed with 1-way ANOVA and the Tukey honest significant difference tests (α=.05). Specimens treated with the airborne particle abrasion method showed significantly higher mean profilometer for surface roughness values in all groups (P.05). With the diamond polishing paste method, lower surface roughness values were achieved in the ZRV and metal ceramic groups acted as the control groups. Different surface-finishing methods affected the color change of the ceramic systems, except for ZRV. Surface-finishing protocols significantly affected the translucency values of the ALV, LITV, and metal ceramic groups (Pceramics tested. The airborne-particle abrasion protocol created rougher surfaces and decreased translucency, and color change in zirconia was not

Usefulness of food chain information provided by Dutch finishing pig producers to control antibiotic residues in pork.

Science.gov (United States)

van Wagenberg, Coen P A; Backus, Gé B C; van der Vorst, Jack G A J; Urlings, Bert A P

2012-11-01

The EU prescribes that food business operators must use food chain information to assist in food safety control. This study analyses usefulness of food chain information about antibiotic usage covering the 60-day period prior to delivery of pigs to slaughter in the control of antibiotic residues in pork. A dataset with 479 test results for antibiotic residues in tissue samples of finishing pigs delivered to a Dutch slaughter company was linked to information provided by pig producers about antibiotic usage in these finishing pigs. Results show that twice as many producers reported using antibiotics in the group of 82 producers with antibiotic residues (11.0%) compared to the group without antibiotic residues (5.5%) (p=0.0686). For 89% of consignments with a finishing pig with antibiotic residues, the producer reported 'did not use antibiotics'. Food chain information about antibiotic usage provided by Dutch pig producers was no guarantee for absence of antibiotic residues in delivered finishing pigs. Copyright © 2012 Elsevier B.V. All rights reserved.

Influence of surface finish on the plasma formation at the skin explosion

International Nuclear Information System (INIS)

Datsko, I M; Chaikovsky, S A; Labetskaya, N A; Rybka, D V; Oreshkin, V I; Khishchenko, K V

2016-01-01

The paper reports on experiments to investigate how the quality of surface finish, i.e., surface roughness, influences the plasma formation in a skin explosion of conductors. The experiments were performed on a MIG terawatt generator with a current amplitude of up to 2.5 MA and current rise time of 100 ns. The plasma formation at the conductor surface and the evolution of the plasma boundary was recorded using a four-frame optical camera with an exposure time of 3 ns per frame. It is shown that the quality of surface finish little affects the onset of plasma formation in a skin explosion of stainless steel and St3 steel conductors at a magnetic field of up to 400 T. (paper)

Effects of Wet and Dry Finishing and Polishing on Surface Roughness and Microhardness of Composite Resins

Science.gov (United States)

Nasoohi, Negin; Hoorizad, Maryam

2017-01-01

Objectives: This study aimed to assess the effect of wet and dry finishing and polishing on microhardness and roughness of microhybrid and nanohybrid composites. Materials and Methods: Thirty samples were fabricated of each of the Polofil Supra and Aelite Aesthetic All-Purpose Body microhybrid and Grandio and Aelite Aesthetic Enamel nanohybrid composite resins. Each group (n=30) was divided into three subgroups of D, W and C (n=10). Finishing and polishing were performed dry in group D and under water coolant in group W. Group C served as the control group and did not receive finishing and polishing. Surface roughness of samples was measured by a profilometer and their hardness was measured by a Vickers hardness tester. Data were analyzed using two-way ANOVA (Pcomposites (Pcomposites (Pcomposites (Pcomposite resins. PMID:29104597

The effects of finishing diet and postmortem ageing on the eating quality of the M. longissimus thoracis of electrically stimulated Brahman steer carcasses.

Science.gov (United States)

Bruce, H L; Stark, J L; Beilken, S L

2004-06-01

Beef from cattle finished on grass will be of similar quality to that from cattle finished on grain when their carcasses are processed using best practice protocols. To test this hypothesis, carcasses of twenty Brahman steers, finished to 400 kg live weight on either Buffel grass pasture (n=10) or grain (n=10), were electrically stimulated with 400 V for 50 s 45 min postmortem, and their beef quality assessed 1 and 14 days postmortem. Hot weight, rump subcutaneous fat thickness and animal rate of growth in the 205 days preceding slaughter were recorded for each carcass as potential influences on beef quality. Quality of the M. longissimus thoracis (LT) at 1 and 14 days postmortem was evaluated using peak Warner-Bratzler shear force, compression, pH, cooking loss and taste panel acceptability, as well as by moisture and crude fat contents measured at 1 day postmortem. Results showed that steers finished on pasture grew the slowest and had the least subcutaneous fat at the same carcass weight. LT from carcasses of steers finished on pasture also had the shortest mean sarcomere lengths, suggesting these muscles may have been cold-affected, but there was no effect of diet on peak shear force. LT from carcasses of steers finished on pasture had the highest mean compression value, possibly because of increased collagen cross-linking associated with slow growth or increased exercise. Ageing significantly decreased LT peak shear force and compression values and increased cooking loss, L (∗), a (∗) and b (∗) values. Taste panellists rated the aged, grass-finished beef the most tender and the best quality; however, the taste panel in this study may have favoured LT from grass-finished steers because it was significantly juicier than LT from the grain-finished steer carcasses. These results indicated that carcass composition and processing conditions interact to exert a greater effect on LT toughness and sensory acceptability than finishing diet. Ageing LT from steers

Concentration data for anthropogenic organic compounds in ground water, surface water, and finished water of selected community water systems in the United States, 2002-05

Science.gov (United States)

Carter, Janet M.; Delzer, Gregory C.; Kingsbury, James A.; Hopple, Jessica A.

2007-01-01

combustion-derived compounds; (10) personal care and domestic use products; (11) plant- or animal-derived biochemicals; (12) refrigerants and propellants; and (13) solvents. Source and finished water samples were collected during phase 2 and analyzed for constituents that were detected frequently during phase 1. This report presents concentration data for AOCs in ground water, surface water, and finished water of CWSs sampled for SWQA studies during 2002-05. Specifically, this report presents the analytical results of samples collected during phase 1 including (1) samples from 221 wells that were analyzed for 258 AOCs; (2) monthly samples from 9 surface-water sites that were analyzed for 258 AOCs during phase 1; and (3) samples from a subset of the wells and surface-water sites located in areas with substantial agricultural production that were analyzed for 3 additional pesticides and 16 pesticide degradates. Samples collected during phase 2 were analyzed for selected AOCs that were detected most frequently in source water during phase 1 sampling; analytical results for phase 2 are presented for (1) samples of source water and finished water from 94 wells; and (2) samples of source water and finished water samples that were collected monthly and during selected flow conditions at 8 surface-water sites. Results of quality-assurance/quality-control samples collected for SWQA studies during 2002-05 also are presented.

Wheat-straw as roughage component in finishing diets of growing ...

African Journals Online (AJOL)

Wheat-straw as roughage component in finishing diets of growing lambs. TS Brand, SWP Cloete, F Franck, GD van der Merwe. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL.

Comparison of triticale cultivars with maize grain for finishing lambs ...

African Journals Online (AJOL)

Comparison of triticale cultivars with maize grain for finishing lambs. TS Brand, GD van der Merwe. Abstract. No Abstract. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians ...

Wheat-straw as roughage component in finishing diets of growing ...

African Journals Online (AJOL)

to use wheat-straw in diets, this study was conducted (i) to determine the degree whereto the inclusion of wheat-straw in finishing diets for lambs affected digestibility, N retention and animal performance, and (ii) to evaluate ammoniated wheat straw as roughage component in a balanced diet, containing. >60% concentrates ...

A preliminary study on growth response of broiler finishers fed ...

African Journals Online (AJOL)

A preliminary study on growth response of broiler finishers fed processed mottle Mucuna beans ( Mucuna pruriens var. utilis ) ... They were fed diets (20% CP, 13 MJME/kg) incorporating 0%, 5% and 10% processed mottle “Mucuna” beans. A completely randomized design was used. Feed and water were supplied and ...

Carcass parameters and meat quality in meat-goat kids finished on chicory, birdsfoot trefoil, or red clover pastures.

Science.gov (United States)

Turner, K E; Cassida, K A; Zerby, H N; Brown, M A

2015-07-01

This study was conducted during the 2009 and 2010 grazing seasons to assess carcass parameters and chevon (goat meat) quality when meat-goat kids (n=72) were finished on pastures of red clover (Trifolium pratense L.; RCL), birdsfoot trefoil (Lotus corniculatus L.; BFT), or chicory (Cichorium intybus L.; CHIC). Final live weight (Pgoats were finished on RCL compared to CHIC with BFT being intermediate. Ribeye area, backfat thickness, body wall thickness, internal fat score, and leg score were not different (P>0.10) among treatments when adjusted for the covariate of carcass weight. Finishing meat-goat kids on RCL, BFT, or CHIC impacted concentrations of fatty acids (FAs) 18:1 trans-10, 18:1 cis-11, 18:2, 18:3 polyunsaturated fatty acids (PUFAs), omega-6, omega-3, and PUFA:saturated fatty acid ratio in longissimus lumborum samples. Finishing meat-goat kids on CHIC, RCL, or BFT pastures produced carcass weights acceptable for most ethnic markets in the USA. Published by Elsevier Ltd.

Development and validation of an rDNA operon based primer walking strategy applicable to de novo bacterial genome finishing.

Directory of Open Access Journals (Sweden)

Alexander William Eastman

2015-01-01

Full Text Available Advances in sequencing technology have drastically increased the depth and feasibility of bacterial genome sequencing. However, little information is available that details the specific techniques and procedures employed during genome sequencing despite the large numbers of published genomes. Shotgun approaches employed by second-generation sequencing platforms has necessitated the development of robust bioinformatics tools for in silico assembly, and complete assembly is limited by the presence of repetitive DNA sequences and multi-copy operons. Typically, re-sequencing with multiple platforms and laborious, targeted Sanger sequencing are employed to finish a draft bacterial genome. Here we describe a novel strategy based on the identification and targeted sequencing of repetitive rDNA operons to expedite bacterial genome assembly and finishing. Our strategy was validated by finishing the genome of Paenibacillus polymyxa strain CR1, a bacterium with potential in sustainable agriculture and bio-based processes. An analysis of the 38 contigs contained in the P. polymyxa strain CR1 draft genome revealed 12 repetitive rDNA operons with varied intragenic and flanking regions of variable length, unanimously located at contig boundaries and within contig gaps. These highly similar but not identical rDNA operons were experimentally verified and sequenced simultaneously with multiple, specially designed primer sets. This approach also identified and corrected significant sequence rearrangement generated during the initial in silico assembly of sequencing reads. Our approach reduces the required effort associated with blind primer walking for contig assembly, increasing both the speed and feasibility of genome finishing. Our study further reinforces the notion that repetitive DNA elements are major limiting factors for genome finishing. Moreover, we provided a step-by-step workflow for genome finishing, which may guide future bacterial genome finishing

Effect of cleaning products on upholstery leather finishes

OpenAIRE

Lara López, Mercedes

2003-01-01

The main objective of the project is to investigate the effects of cleaning products on upholstery leather finishes. Focusing on products applicable to upholstery leather cleaning, non-typical leather cleaners (and possible contaminants) or ink removers, in order to find out their behaviour, understanding how they work and if they are suitable for their purpose. Moreover an initial investigation about mechanism of soiling is proposed, in order, in the future, to avoid the soiling or develop a...

Agronomic Characteristics Related to Grain Yield and Nutrient Use Efficiency for Wheat Production in China.

Directory of Open Access Journals (Sweden)

Limin Chuan

Full Text Available In order to make clear the recent status and trend of wheat (Triticum aestivum L. production in China, datasets from multiple field experiments and published literature were collected to study the agronomic characteristics related to grain yield, fertilizer application and nutrient use efficiency from the year 2000 to 2011. The results showed that the mean grain yield of wheat in 2000-2011 was 5950 kg/ha, while the N, P2O5 and K2O application rates were 172, 102 and 91 kg/ha on average, respectively. The decrease in N and P2O5 and increase in K2O balanced the nutrient supply and was the main reason for yield increase. The partial factor productivity (PFP, kg grain yield produced per unit of N, P2O5 or K2O applied values of N (PFP-N, P (PFP-P and K (PFP-K were in the ranges of 29.5~39.6, 43.4~74.9 and 44.1~76.5 kg/kg, respectively. While PFP-N showed no significant changes from 2000 to 2010, both PFP-P and PFP-K showed an increased trend over this period. The mean agronomic efficiency (AE, kg grain yield increased per unit of N, P2O5 or K2O applied values of N (AEN, P (AEP and K (AEK were 9.4, 10.2 and 6.5 kg/kg, respectively. The AE values demonstrated marked inter-annual fluctuations, with the amplitude of fluctuation for AEN greater than those for AEP and AEK. The mean fertilizer recovery efficiency (RE, the fraction of nutrient uptake in aboveground plant dry matter to the nutrient of fertilizer application values of N, P and K in the aboveground biomass were 33.1%, 24.3% and 28.4%, respectively. It was also revealed that different wheat ecological regions differ greatly in wheat productivity, fertilizer application and nutrient use efficiency. In summary, it was suggested that best nutrient management practices, i.e. fertilizer recommendation applied based on soil testing or yield response, with strategies to match the nutrient input with realistic yield and demand, or provided with the 4R's nutrient management (right time, right rate, right

SURFACE FINISHES ON STAINLESS STEEL REDUCE BACTERIAL ATTACHMENT AND EARLY BIOFILM FORMATION: SCANNING ELECTRON AND ATOMIC FORCE MICROSCOPY STUDY

Science.gov (United States)

Three common finishing treatments of stainless steel that are used for equipment during poultry processing were tested for resistance to bacterial contamination. Methods were developed to measure attached bacteria and to identify factors that make surface finishes susceptible or ...

Radiation environmental monitoring and assessment of plant-221 site ten years after decommissioning

International Nuclear Information System (INIS)

Li Yang; Gu Zhijie; Pan Wei; Ren Xiaona; Hu Xiaolin; She Haiqiang

2011-01-01

More than 10 years have passed since nuclear facility decommissioning practice for Plant-221 finished. Environmental radiation monitoring and post assessment of the decommissioning site of Plant-221 was carried out during 2003-2006, which was organized by Department of Environmental Protection and executed by China Institute for Radiation Protection, Environmental Radiation Monitoring station of Qinghai Province, etc. It shows that the decommissioning practice for Plant-221 complied with relevant limits for decommissioning, and its environmental radiation situation has not had significant change in general after 10 years, and the potential impact to the public and the environmental is acceptable. (authors)

Fabrication of high precision metallic freeform mirrors with magnetorheological finishing (MRF)

Science.gov (United States)

Beier, Matthias; Scheiding, Sebastian; Gebhardt, Andreas; Loose, Roman; Risse, Stefan; Eberhardt, Ramona; Tünnermann, Andreas

2013-09-01

The fabrication of complex shaped metal mirrors for optical imaging is a classical application area of diamond machining techniques. Aspherical and freeform shaped optical components up to several 100 mm in diameter can be manufactured with high precision in an acceptable amount of time. However, applications are naturally limited to the infrared spectral region due to scatter losses for shorter wavelengths as a result of the remaining periodic diamond turning structure. Achieving diffraction limited performance in the visible spectrum demands for the application of additional polishing steps. Magnetorheological Finishing (MRF) is a powerful tool to improve figure and finish of complex shaped optics at the same time in a single processing step. The application of MRF as a figuring tool for precise metal mirrors is a nontrivial task since the technology was primarily developed for figuring and finishing a variety of other optical materials, such as glasses or glass ceramics. In the presented work, MRF is used as a figuring tool for diamond turned aluminum lightweight mirrors with electroless nickel plating. It is applied as a direct follow-up process after diamond machining of the mirrors. A high precision measurement setup, composed of an interferometer and an advanced Computer Generated Hologram with additional alignment features, allows for precise metrology of the freeform shaped optics in short measuring cycles. Shape deviations less than 150 nm PV / 20 nm rms are achieved reliably for freeform mirrors with apertures of more than 300 mm. Characterization of removable and induced spatial frequencies is carried out by investigating the Power Spectral Density.

Pengaruh Suhu dan Metode Perlakuan Panas terhadap Sifat Fisika dan Kualitas Finishing Kayu Mahoni

Directory of Open Access Journals (Sweden)

Ragil Widyorini

2016-03-01

Full Text Available Perlakuan panas dikenal sebagai metode yang dapat digunakan untuk meningkatkan stabilitas dimensi dan menurunkan higroskopisitas. Di sisi lain, perlakuan panas dapat membuat warna kayu menjadi lebih gelap, penurunan sifat mekanika kayu, dan sifat wetabilitas kayu. Oleh karena itu, penelitian mengenai perlakuan panas pada kondisi yang optimum sangat menarik untuk dilakukan agar menghasilkan kayu dengan kualitas yang lebih baik. Tujuan penelitian ini adalah mengetahui pengaruh interaksi suhu dan metode perlakuan panas terhadap sifat fisika dan kualitas finishing kayu mahoni. Contoh uji perlakuan dibuat dari kayu mahoni yang berasal dari industri penggergajian kayu rakyat. Penelitian ini menggunakan 2 metode perlakuan panas yaitu metode oven dan penguapan (steaming pada variasi suhu 90°C, 120°C, dan 150°C selama 2 jam waktu efektif. Pengujian sifat fisika diuji berdasarkan standar ASTM, yang meliputi : kadar air seimbang, perubahan dimensi, perubahan warna, dan wetabilitas. Pengujian finishing meliputi cross cut test, uji delaminasi, dan uji kekilapan (glossy test. Hasil penelitian menunjukkan bahwa interaksi antara suhu dan metode perlakuan panas berpengaruh sangat nyata terhadap perubahan warna, serta berpengaruh nyata terhadap penyusutan radial, cross cut test, dan uji delaminasi. Metode oven menghasilkan contoh uji dengan kadar air dan pengembangan radial yang lebih rendah, warna yang lebih terang, serta uji delaminasi yang lebih baik dibandingkan dengan metode penguapan. Kata kunci: perlakuan panas, metode oven, metode penguapan, suhu, finishing   Effect of temperature and heat treatment on physical properties and finishing quality of mahagony wood Abstract Heat treatment is well known as a method for increasing dimensional stability and reducing hygroscopicity of wood. However, heat tratment can cause the color of wood become darker and reduce the wettability, as well as its mechanical properties. Therefore, the optimum condition of heat

A transcript finishing initiative for closing gaps in the human transcriptome

DEFF Research Database (Denmark)

Sogayar, Mari Cleide; Camargo, Anamaria A; Bettoni, Fabiana

2004-01-01

We report the results of a transcript finishing initiative, undertaken for the purpose of identifying and characterizing novel human transcripts, in which RT-PCR was used to bridge gaps between paired EST clusters, mapped against the genomic sequence. Each pair of EST clusters selected...

The First Amendment: The Finished Mystery Case and World War I.

Science.gov (United States)

Mueller, Jean West; Schamel, Wynell Burroughs

1990-01-01

Introduces the censorship, and imprisonment of Jehovah's Witnesses who distributed, "The Finished Mystery," which contained antiwar statements deemed seditious during World War I. Asks students to examine a Justice Department document pertaining to the case. Helps students decide whether national security needs should override First…

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false What controls and acceptance criteria must I have... POSITRON EMISSION TOMOGRAPHY DRUGS (Eff. 12-12-2011) Finished Drug Product Controls and Acceptance § 212.70 What controls and acceptance criteria must I have for my finished PET drug products? (a) Specifications...

Comparison of U.S. Environmental Protection Agency and U.S. Composting Council microbial detection methods in finished compost and regrowth potential of Salmonella spp. and Escherichia coli O157:H7 in finished compost.

Science.gov (United States)

Reynnells, Russell; Ingram, David T; Roberts, Cheryl; Stonebraker, Richard; Handy, Eric T; Felton, Gary; Vinyard, Bryan T; Millner, Patricia D; Sharma, Manan

2014-07-01

Bacterial pathogens may survive and regrow in finished compost due to incomplete thermal inactivation during or recontamination after composting. Twenty-nine finished composts were obtained from 19 U.S. states and were separated into three broad feedstock categories: biosolids (n=10), manure (n=4), and yard waste (n=15). Three replicates of each compost were inoculated with ≈ 1-2 log CFU/g of nonpathogenic Escherichia coli, Salmonella spp., and E. coli O157:H7. The U.S. Environmental Protection Agency's (EPA) protocols and U.S. Composting Council's (USCC) Test Methods for the Examination of Composting and Compost (TMECC) were compared to determine which method recovered higher percentages of inoculated E. coli (representing fecal coliforms) and Salmonella spp. from 400-g samples of finished composts. Populations of Salmonella spp. and E. coli O157:H7 were determined over 3 days while stored at 25°C and compared to physicochemical parameters to predict their respective regrowth potentials. EPA Method 1680 recovered significantly (p=0.0003) more inoculated E. coli (68.7%) than TMECC 07.01 (48.1%) due to the EPA method using more compost in the initial homogenate, larger transfer dilutions, and a larger most probable number scheme compared to TMECC 07.01. The recoveries of inoculated Salmonella spp. by Environmental Protection Agency Method 1682 (89.1%) and TMECC 07.02 (72.4%) were not statistically significant (p=0.44). The statistically similar recovery percentages may be explained by the use of a nonselective pre-enrichment step used in both methods. No physicochemical parameter (C:N, moisture content, total organic carbon) was able to serve as a sole predictor of regrowth of Salmonella spp. or E. coli O157:H7 in finished compost. However, statistical analysis revealed that the C:N ratio, total organic carbon, and moisture content all contributed to pathogen regrowth potential in finished composts. It is recommended that the USCC modify TMECC protocols to test

MICROSCOPY, MICRO-CHEMISTRY AND FTIR AS ANALYTICAL TOOLS FOR IDENTIFYING TRANSPARENT FINISHES CASE STUDIES FROM ASTRA MUSEUM – SIBIU

Directory of Open Access Journals (Sweden)

Maria Cristina TIMAR

2015-12-01

Full Text Available Conservation of cultural heritage relies on scientific investigation of artefacts, a key point being identification of the original materials. In this context, besides wood species identification, investigation of finishing layers is of ultimate importance for old furniture and any other wooden objects with historic, documentary or artistic value. The present paper refers to a series of micro-destructive investigation methods applied for identification of finishing materials, namely: simple in situ and laboratory physical tests, optical microscopy, micro-chemistry and FTIR – ATR analysis. Small samples of finishing layers were taken from four furniture objects belonging to CNM ASTRA Sibiu and were analysed according to the usual procedures of the laboratories from Sibiu and Brasov. The results showed that physical tests and microscopy are useful to get basic information on the samples’ morphology and possible classes of coating materials, while micro-chemistry revealed by some successive tests more specific information on the type of finishing materials. FTIR - ATR is a rapid method of identifying the coating materials based on available reference samples or spectra. However, this is not always straightforward and preliminary physical tests of solubility are useful to select the adequate references, while micro-chemistry tests could complete the FTIR result, especially for those components of the finishing layer present in very small amounts (less than 5%, bellow the FTIR sensitivity. Corroboration of microscopy, physical and micro-chemistry tests with FTIR can provide more reliable results in terms of finishes identification and also valuable information for restoration.

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Science.gov (United States)

2010-07-01

... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND... processes raw or cured cattle or cattle-like hides into finished leather by hair save or pulp unhairing, vegetable tanning or alum, syntans, oils and other agents for tanning, and retan-wet finishing. ...

Effect of genotype, finishing system, and sex on physiochemical characteristics of goat meat

Directory of Open Access Journals (Sweden)

Luciana Rodrigues

2011-12-01

Full Text Available Seventy-eight kids of both sexes and five genotypes were used: Alpine, ½ Boer + ½ Alpine (½ BA, ¾ Boer + ¼ Alpine, ½ Anglo-nubian + ½ Alpine and "tricross" (½ Anglo-nubian + ¼ Boer + ¼ Alpine with initial average weight of 14.1 ± 2.5. The objective was to evaluate the effect of genotype, finishing system, and sex on the physiochemical characteristics of goat meat. Finishing systems were: ST1 - kid + dam in pasture and ST2 - weaned kid and feedlot. Kids in ST1 were kept in an area with Panicum maximum cv. Tanzania, and after grazing, water and mineral salt/mix were fed ad libitum to the animals. The animals in ST2 were confined in collective pens distributed according to genotypes and received diet with 16% CP and 73% TDN. The values of pH, a* (red content, Cooking Loss (CL, and Ether Extract (EE percentage were influenced by genotype. Values for red content (a* and L* (brightness, CL and percentages of moisture, protein, EE, and ash were influenced by the finishing system. Longissimus dorsi muscle from animals ½ BA exhibited better physiochemical characteristics. For greater tenderness and higher percentages of fat, consumers should choose female kid goat meat.

Efficacy of XP-endo Finisher File in Removing Calcium Hydroxide from Simulated Internal Resorption Cavity.

Science.gov (United States)

Keskin, Cangül; Sariyilmaz, Evren; Sariyilmaz, Öznur

2017-01-01

The aim of this study was to evaluate the effect of supplementary use of XP-endo Finisher file, passive ultrasonic activation (PUI), EndoActivator (EA), and CanalBrush (CB) on the removal of calcium hydroxide (CH) paste from simulated internal resorption cavities. The root canals of 110 extracted single-rooted teeth with straight canals were prepared up to size 50. The specimens were split longitudinally, and standardized internal resorption cavities were prepared with burs. The cavities and root canals were filled with CH paste. The specimens were divided into 5 groups as follows: XP-endo Finisher, EA, PUI, CB, and syringe irrigation (SI). The root canals were irrigated with 5.25% NaOCl and 17% EDTA for 2 minutes, respectively. Apart from the SI group, both solutions were activated by using tested techniques for 1 minute. The quantity of CH remnants on resorption cavities was scored. Data were analyzed by using Kruskal-Wallis H and Mann-Whitney U tests. XP-endo Finisher and PUI removed significantly more CH than SI, EA, and CB (P  .05). Differences among SI, EA, and CB were also non-significant (P > .05). None of the tested techniques render the simulated internal resorption cavities free of CH debris. XP-endo Finisher and PUI were superior to SI, CB, and EA. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

40 CFR Figure 1 to Subpart Tttt of... - Example Logs for Recording Leather Finish Use and HAP Content

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Example Logs for Recording Leather Finish Use and HAP Content 1 Figure 1 to Subpart TTTT of Part 63 Protection of Environment ENVIRONMENTAL... Finishing Operations Part 63, Subpt. TTTT, Fig. 1 Figure 1 to Subpart TTTT of Part 63—Example Logs for...

[Comparative analysis of 3D data visibility of the prepared tooth finishing line on a synthetic jaw model, captured by international scanners in a laboratory conditions].

Science.gov (United States)

Ryakhovskiy, A N; Kostyukova, V V

The aim of the study was to compare accuracy of digital impression's finishing line and the zone under it taken by different intraoral scanning systems. Parameters of comparison were: different level of the finishing line to the gingiva and width of sulcus after retraction. For this purpose two synthetic jaw models with prepared teeth were scanned using intraoral scanning systems: 3D Progress (MHT S.P.A., IT - MHT Optic Research AG, CH); True Definition (3M ESPE, USA); Trios (3Shape A/S, DNK); CEREC AC Bluecam, CEREC Omnicam (Sirona Dental System GmbH, DE); Planscan (Planmeca, FIN) (each n=10). Reference-scanning was done by ATOS Core (GOM mbH, DE). The resulting digital impressions were superimposed with the master-scan. The lowest measured deviations (trueness) for intraoral scanners, where the finishing line was 0.5 mm above gingiva were with scanner True Definition - 18.8±6.63 (on the finishing line) and 51.0±14.33 µm (0.3 mm under the finishing line). In conditions where finishing line was on the same level with gingiva, scanner Trios showed the best results: 17.0±3.96 and 52.7±6.52 µm. When the finishing line was 0.5 mm under gingiva, none of the testing scanners could visualize the zone 0.3 mm lower the finishing line. The best results for accuracy o the finishing line in that circumstances showed Trios: 15.1±5.05 µm. The optimum visualization of the finishing line and the zone under it was reached when the sulcus was 0.3 mm after retraction. Thus, the best accuracy was obtained with Trios: 10.3±2.69 (on the finishing line) and 57.2±13.58 µm (0.3 mm under finishing line). The results show that intraoral scanners also provide enough accuracy for indicating finishing line and the zone under it in different conditions of preparation and gingiva retraction. However, not all of the testing scanners can properly indicate finishing line and the zone under it when shoulder is below gingiva and the width of sulcus is less than 0.2 mm.

Finishing and Special Motifs: Lessons Learned from CRISPR Analysis Using Next-Generation Draft Sequences (7th Annual SFAF Meeting, 2012)

Energy Technology Data Exchange (ETDEWEB)

Campbell, Catherine

2012-06-01

Catherine Campbell on "Finishing and Special Motifs: Lessons learned from CRISPR analysis using next-generation draft sequences" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Control of formaldehyde and TVOC emission from wood-based flooring composites at various manufacturing processes by surface finishing.

Science.gov (United States)

Kim, Sumin

2010-04-15

This paper assesses the reproducibility of testing formaldehyde and TVOC emission behavior from wood flooring composites bonded by urea-formaldehyde resin at various manufacturing steps for surface finishing materials. The surface adhesion step of laminate flooring for this research was divided into two steps; HDF only and HDF with LPMs. In the case of engineered flooring, the manufacturing steps were divided into three steps; plywood only, fancy veneer bonded on plywood and UV coated on fancy veneer with plywood. Formaldehyde and VOCs emission decreased at the process of final surface finishing materials; LPMs were applied on the surface of HDF for laminate flooring. Although emissions increased when fancy veneer was bonded onto plywood in the case of engineered flooring, emission was dramatically reduced up to similar level with plywood only when final surface finishing; UV-curable coating was applied on fancy veneer. This study suggests that formaldehyde and VOCs emission from floorings can be controlled at manufacturing steps for surface finishing. 2009 Elsevier B.V. All rights reserved.

Finishing of the cold mass assembly

CERN Multimedia

Maximilien Brice

2001-01-01

Photo 1 Zoom of the lyre-side end of the active part assembly. The extremity of the shrinking cylinder has been bevelled in view of welding the end cover. Photo 2 General view of the finishing station showing the special supporting structures (blue and yellow structures) needed for the geometric measurements and for the alignment operations. Photo 3 Zoom of the lyre-side end of the active part assembly. One can also see the auxiliary bus bars needed to power the corrector magnets that are installed in the dipole cold mass assembly. Photo 4 Technicians are putting in order the instrumentation wires. The prototype magnets were equipped with numerous sensors to monitor key parameters during the performance tests at cold conditions.

Heterogeneity among methicillin-resistant Staphylococcus aureus from Italian pig finishing holdings

DEFF Research Database (Denmark)

Battisti, A.; Franco, A.; Merialdi, G.

2010-01-01

A survey for methicillin-resistant Staphylococcus aureus (MRSA) in finishing pig holdings was carried out in Italy in 2008. MRSA isolates were characterised by spa-. SCCmec- and antimicrobial susceptibility typing. A prevalence of 38% (45/118, 95% CI 29.4-46.9%) positive holdings was observed...

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Science.gov (United States)

2010-07-01

... drying apparatus and electrical connections and wiring thereto shall not be located within spray... apparatus, the drying apparatus, and the ventilating system of the spray enclosure shall be equipped with... 29 Labor 5 2010-07-01 2010-07-01 false Spray finishing using flammable and combustible materials...

Decontamination and decommissioning assessment for the Waste Incineration Facility (Building 232-Z) Hanford Site, [Hanford], WA

International Nuclear Information System (INIS)

Dean, L.N.

1994-02-01

Building 232-Z is an element of the Plutonium Finishing Plant (PFP) located in the 200 West Area of the Hanford Site. From 1961 until 1972, plutonium-bearing combustible materials were incinerated in the building. Between 1972 and 1983, following shutdown of the incinerator, the facility was used for waste segregation activities. The facility was placed in retired inactive status in 1984 and classified as a Limited Control Facility pursuant to DOE Order 5480.5, Safety of Nuclear Facilities, and 6430.1A, General Design Criteria. The current plutonium inventory within the building is estimated to be approximately 848 grams, the majority of which is retained within the process hood ventilation system. As a contaminated retired facility, Building 232-Z is included in the DOE Surplus Facility Management Program. The objective of this Decontamination and Decommissioning (D ampersand D) assessment is to remove Building 232-Z, thereby elmininating the radiological and environmental hazards associated with the plutonium inventory within the structure. The steps to accomplish the plan objectives are: (1) identifying the locations of the most significant amounts of plutonium, (2) removing residual plutonium, (3) removing and decontaminating remaining building equipment, (4) dismantling the remaining structure, and (5) closing out the project

Decontamination and decommissioning assessment for the Waste Incineration Facility (Building 232-Z) Hanford Site, [Hanford], WA

Energy Technology Data Exchange (ETDEWEB)

Dean, L.N. [Advanced Sciences, Inc., (United States)

1994-02-01

Building 232-Z is an element of the Plutonium Finishing Plant (PFP) located in the 200 West Area of the Hanford Site. From 1961 until 1972, plutonium-bearing combustible materials were incinerated in the building. Between 1972 and 1983, following shutdown of the incinerator, the facility was used for waste segregation activities. The facility was placed in retired inactive status in 1984 and classified as a Limited Control Facility pursuant to DOE Order 5480.5, Safety of Nuclear Facilities, and 6430.1A, General Design Criteria. The current plutonium inventory within the building is estimated to be approximately 848 grams, the majority of which is retained within the process hood ventilation system. As a contaminated retired facility, Building 232-Z is included in the DOE Surplus Facility Management Program. The objective of this Decontamination and Decommissioning (D&D) assessment is to remove Building 232-Z, thereby elmininating the radiological and environmental hazards associated with the plutonium inventory within the structure. The steps to accomplish the plan objectives are: (1) identifying the locations of the most significant amounts of plutonium, (2) removing residual plutonium, (3) removing and decontaminating remaining building equipment, (4) dismantling the remaining structure, and (5) closing out the project.

CSAR 81-001 addendum 2: Use of a plexiglass contamination barrier in HC-227-T

International Nuclear Information System (INIS)

Chiao, T.

1994-01-01

Plutonium Finish Plant (PFP) Engineering requested a criticality safety evaluation (Appendix 1) to support a revision of Criticality Prevention Specification CPS-Z-165-80601 allowing a plexiglass enclosure (PGE) to be placed inside the HC-227T hood as a contamination barrier. The HC-227T hood is the receiving/transfer enclosure for Pu nitrate solution contained in Product Removal containers (PR Cans), L10 Containers (L10, Fl-10, 10 L) or L-3 Containers. Within the HC-227T, a 1.349 square meter (15 square foot) enclosure, PGE, has been created to provide contamination control around the weighing scale. Two or more standard criticality drains shall be installed on this enclosure prior to beneficial usage. The evaluation considered the normal process, spillage scenarios, waste/container accumulations within the enclosure, and interactions of Pu within the enclosure as well as other containers external to the enclosure. The results from the criticality safety analysis by CRA shows that such as contamination barrier can be placed inside the HC-227T Hood if the PGE is equipped with adequate criticality drains. In addition, other limits as well as administrative controls listed in CPS-Z-165-80601 Rev./Mod. B/0 and CPS-Z-165-80010 Rev./Mod. C/1 shall also apply

Pulsed-field profile diversities of Salmonella Enteritidis, S. Infantis, and S. Corvallis in Japan.

Science.gov (United States)

Murakami, Koichi; Noda, Tamie; Onozuka, Daisuke; Kimura, Hirokazu; Fujimoto, Shuji

2017-08-16

The diversity of pulsed-field profiles (PFPs) within non-typhoidal Salmonella subtypes influences epidemiological analyses of Salmonella outbreaks. Therefore, determining the PFP diversity of each Salmonella serovar is important when evaluating current circulating strains. This study examined the PFP diversity of three important public health Salmonella enterica subspecies enterica serovars, S . Enteritidis (n=177), S . Infantis (n=205), and S . Corvallis (n=90), using pulsed-field gel electrophoresis. Isolates were collected from several sources, primarily from chicken-derived samples, in the Kyushu-Okinawa region of Japan between 1989 and 2005. S . Enteritidis isolates displayed 51 distinct PFPs (E-PFPs), with 92 (52.0%) and 32 (18.1%) isolates displaying types E-PFP1 and E-PFP10, respectively. The 205 S . Infantis isolates showed 54 distinct PFPs (I-PFPs), with 87 (42.4%) and 36 (17.6%) isolates being I-PFP4 and I-PFP2, respectively. I-PFP18 was the dominant I-PFP of layer chicken isolates across a 5-year period. Fourteen distinct S . Corvallis PFPs were detected. Simpson's index results for the genetic diversities of S . Enteritidis, S . Infantis, and S . Corvallis isolates were 0.70, 0.79, and 0.78, respectively. None of the E-PFPs or I-PFPs of layer chicken isolates overlapped with those of broiler chicken isolates, and the dominant clonal lines existed for >10 years. In conclusion, limited PFP diversities were detected amongst S . Enteritidis, S. Infantis, and S. Corvallis isolates of primarily chicken-derived origins in the Kyushu-Okinawa region of Japan. Therefore, it is important to take into account these limitations in PFP diversities in epidemiological analyses of Salmonella outbreaks.

Effects of different space allowances on growth performance, blood profile and pork quality in a grow-to-finish production system.

Science.gov (United States)

Jang, J C; Jin, X H; Hong, J S; Kim, Y Y

2017-12-01

This experiment was conducted to evaluate the optimal space allowance on growth performance, blood profile and pork quality of growing-finishing pigs. A total of ninety crossbred pigs [(Yorkshire×Landrace)×Duroc, 30.25±1.13 kg] were allocated into three treatments (0.96: four pigs/pen, 0.96 m2/pig; 0.80: five pigs/pen, 0.80 m2/pig; 0.69: six pigs/pen, 0.69 m2/pig) in a randomized complete block design. Pigs were housed in balanced sex and had free access to feed in all phases for 14 weeks (growing phase I, growing phase II, finishing phase I, and finishing phase II). There was no statistical difference in growing phase, but a linear decrease was observed on average daily gain (ADG, pspace allowance in late finishing phase. On the other hand, a quadratic effect was observed on gain to feed ratio in early finishing phase (pspace allowance (pspace allowance. Floor area allowance did not affect pork colors, but shear force linearly increased as floor space decreased (pspace allocation. Serum IgG was linearly ameliorated as space allowance increased on 10 week (pspace allowance deteriorates the immune system as well as growth performance of pigs, resulting in poor pork quality. Recommended adequate space allowance in a grow-to-finish production system is more than 0.80 m2/pig for maximizing growth performance and production efficiency.

Presence of toxic metals and their effects in finished leather goods

International Nuclear Information System (INIS)

Rana, B.B.; Ehsan, A.M.

2016-01-01

This study examines the presence of heavy metals in different types of leather finished goods. Various leather items like gloves, shoe soles and leather pieces for jackets were tested using Atomic Absorption Spectrophotometry and their toxic effects in our environment are discussed. Cadmium, lead and chromium are the most common heavy metals present in leather finished goods and are a cause for concern. Many countries in Europe and America have banned or limited their use in leather processing. This study reveals that the levels of heavy metals in most of the leather goods manufactured by different companies in Pakistan are within permissible limits. However, in some of the samples tested in this study, the amounts of cadmium, lead and chromium are considerably high which requires special attention from all stakeholders to bring it down to acceptable level. Failing to do so will be detrimental for export of these leather goods to Europe and America. (author)

Effect of Lysine to Digestible Energy Ratio on Growth Performance and Carcass Characteristics in Finishing Pigs

Directory of Open Access Journals (Sweden)

S. B. Cho

2012-11-01

Full Text Available This experiment was performed to investigate the effects of lysine (Lys to DE ratio on growth performance, and carcass characterics in finishing barrows. Ninety six cross-bred finishing barrows ((Landrace×Yorkshire ×Duroc, average BW 58.25±0.48 kg were assigned as a randomized complete block design by 2 energy levels and 4 Lys:DE ratios on the basis of BW to one of 8 treatments with 3 replications with 4 animals per pen. The levels of DE and Lys:DE ratio for each treatment were i DE 3.35 Mcal/kg, 1.5 g Lys/Mcal DE, ii DE 3.35 Mcal/kg, 1.8 g Lys/Mcal DE, iii DE 3.35 Mcal/kg, 2.1 g Lys/Mcal DE, iv DE 3.35 Mcal/kg, 2.4 g Lys/Mcal DE, v DE 3.60 Mcal/kg, 1.5 g Lys/Mcal DE, vi DE 3.60 Mcal/kg, 1.8 g Lys/Mcal DE, vii DE 3.60 Mcal/kg, 2.1 g Lys/Mcal DE, viii DE 3.60 Mcal/kg, 2.4 g Lys/Mcal DE. During finishing period from 58 kg to 103 kg of BW, increased energy density in the diet increased (p<0.05 ADG and gain:feed ratio, but did not influence ADFI. As Lys:DE ratio was increased, ADG, ADFI and gain:feed ratio were improved in finishing barrows (p<0.05. There were positive interactions (p<0.05 between carcass weight, grade, and backfat thickness and energy density and Lys level (p<0.05. In conclusion, data from our current study suggest that maximum yields including ADG, gain:feed ratio, carcass weight and grade can be achieved by administrating finishing pigs with an ideal Lys:DE ratio, Lys 2.1 g/DE Mcal.

Progressive building methods in nuclear power plant construction

International Nuclear Information System (INIS)

Sikura, V.

1980-01-01

A detailed description is given of the new prospective technologies used in the construction of the Bohunice V-1 nuclear power plant. They include the use of steel and large-area forms, the use of profile sheets as a substitute for forms, assembled raw partitions, wall shells consisting of clamped porous concrete slabs, assembled roof shells, special finish of concrete walls, bearing wall deep foundation, the use of modern building machinery for concreting, reinforcing and welding works. (M.S.)

Estimativas de repetibilidade de alguns caracteres de produção em mangueira Estimate of repeatability of some traits of production in mango tree

Directory of Open Access Journals (Sweden)

João Gomes da Costa

2003-04-01

Full Text Available O presente trabalho objetivou estimar o coeficiente de repetibilidade para os caracteres número total de frutos por planta (NTF, produção de frutos por planta (PFP e peso médio de fruto (PMF, e determinar o número mínimo de avaliações que devem ser feitas para uma predição acurada do valor real dos indivíduos. As estimativas de repetibilidade foram realizadas pelo método dos componentes principais a partir da matriz de correlação. Os coeficientes de repetibilidade estimados foram de: 0,51; 0,53 e 0,81, associados aos coeficientes de determinação (R² de 80,44%, 81,60% e 94,41% respectivamente, para NTF, PFP e PMF. A estimativa do coeficiente de repetibilidade da característica peso médio do fruto demonstrou alta regularidade na superioridade dos indivíduos de um ciclo para outro, sendo necessários três ciclos de avaliações para predizer o valor real dos indivíduos com nível de certeza acima de 90%. Apesar de as características número de frutos por planta e produção de frutos por planta terem influência ambiental, quatro medições permitem obter coeficientes de determinação próximos de 80%.The objective of this papers was to estimate the repeatability coefficient of the total number of fruit per plant (TNF, production of fruit per plant (PFP and average fruit weight (AWF, while the number of measures that should be performed for an efficient selection of the genotypes under evaluation were determined. Analysis were made using principal components. The estimates of the repeatability were of: 0.51; 0.53 and 0.81, associated to the determination coefficients (R² of 80.44%, 81.60% and 94.41, respectively, for TNF, PFP and WMF. The estimate of the repeatability coefficient of the WMF demonstrated high regularity at the superiority of the individuals from one cycle to another, so the evaluation of three cycles was enough to predict the individual real value with R² above 90%. In spite of the traits TNF and PFP have

Estimation of tool wear length in finish milling using a fuzzy inference algorithm

Science.gov (United States)

Ko, Tae Jo; Cho, Dong Woo

1993-10-01

The geometric accuracy and surface roughness are mainly affected by the flank wear at the minor cutting edge in finish machining. A fuzzy estimator obtained by a fuzzy inference algorithm with a max-min composition rule to evaluate the minor flank wear length in finish milling is introduced. The features sensitive to minor flank wear are extracted from the dispersion analysis of a time series AR model of the feed directional acceleration of the spindle housing. Linguistic rules for fuzzy estimation are constructed using these features, and then fuzzy inferences are carried out with test data sets under various cutting conditions. The proposed system turns out to be effective for estimating minor flank wear length, and its mean error is less than 12%.

Consumer sensory evaluation and chemical composition of beef gluteus medius and triceps brachii steaks from cattle finished on forage or concentrate diets.

Science.gov (United States)

Chail, A; Legako, J F; Pitcher, L R; Ward, R E; Martini, S; MacAdam, J W

2017-04-01

The objective of this study was to assess the impact of cattle finishing diet and muscle type on meat quality. Consumer sensory response, proximate composition, Warner-Bratzler shear force (WBSF), fatty acid composition, and volatile compounds were assessed from the gluteus medius (GM) and triceps brachii (TB) muscles of cattle ( = 6 per diet) which were grain-finished (USUGrain) on conventional feedlot or 2 forage diets, a perennial legume, birdsfoot trefoil-finished (USUBFT; ), and grass-finished (USUGrass; ). Diet had an interacting effect with muscle for all sensory attributes ( ≤ 0.002), except aroma and flavor ( ≥ 0.078). In forage-finished beef, tenderness, fattiness, overall liking, and WBSF tenderness of GM was greater ( 0.05) but the juiciness of TB was more liked than USUGrain GM ( 0.05) between GM and TB. Lower ( 0.05) to both USUGrass and USUGrain beef. However, IMF percent was not impacted by muscle type ( = 0.092). The ratio of -6:-3 fatty acids was affected by muscle dependent on diet ( = 0.016). The ratio of -6:-3 fatty acids was affected by the interaction of muscle × diet ( = 0.016). Between forage diets (USUGrass and USUBFT), -6:-3 ratios were similar ( > 0.05) between GM and TB, whereas within USUGrain, the GM was greater ( 0.05). Strecker aldehydes, ketones, pyrazines, and methional were affected ( ≤ 0.036) by muscle and found to have a greater concentration in GM compared with TB. Overall, consumers determined that USUGrain GM and TB had similar ( > 0.05) quality ratings. However, within forage-finished beef, the GM was perceived more frequently ( consumer group grilled GM and TB steaks, grain-finished beef provided more uniform quality and eating experience compared with forage-finished beef.

Kinetic model for the formation of acrylamide during the finish-frying of commercial french fries.

Science.gov (United States)

Parker, Jane K; Balagiannis, Dimitrios P; Higley, Jeremy; Smith, Gordon; Wedzicha, Bronislaw L; Mottram, Donald S

2012-09-12

Acrylamide is formed from reducing sugars and asparagine during the preparation of French fries. The commercial preparation of French fries is a multistage process involving the preparation of frozen, par-fried potato strips for distribution to catering outlets, where they are finish-fried. The initial blanching, treatment in glucose solution, and par-frying steps are crucial because they determine the levels of precursors present at the beginning of the finish-frying process. To minimize the quantities of acrylamide in cooked fries, it is important to understand the impact of each stage on the formation of acrylamide. Acrylamide, amino acids, sugars, moisture, fat, and color were monitored at time intervals during the frying of potato strips that had been dipped in various concentrations of glucose and fructose during a typical pretreatment. A mathematical model based on the fundamental chemical reaction pathways of the finish-frying was developed, incorporating moisture and temperature gradients in the fries. This showed the contribution of both glucose and fructose to the generation of acrylamide and accurately predicted the acrylamide content of the final fries.

DIRECT DISMANTLING OF REPROCESSING PLANT CELLS THE EUREX PLANT EXPERIENCEe2d12c

International Nuclear Information System (INIS)

Gili, M.; Troiani, F.; Risoluti, P.

2003-01-01

After finishing the reprocessing campaigns in 1970-1983, the EUREX pilot reprocessing plant of ENEA Saluggia Research Center started into a new phase, aiming to materials and irradiated fuel systemation and radioactive wastes conditioning. In 1997 the project ''CORA'' for a vitrification plant for the high and intermediate liquid radioactive wastes started. The ''CORA'' plant will be hosted in some dismantled cells of the EUREX plant, reusing many of the EUREX plant auxiliary systems, duly refurbished, saving money and construction time and avoiding a new nuclear building in the site. Two of the cells that will be reused were part of the EUREX chemical process (solvent recovery and 2nd extraction cycle) and the components were obviously internally contaminated. In 2000 the direct (hands-on) dismantling of one of them started and has been completed in summer 2002; the second one will be dismantled in the next year and then the ''CORA'' plant will be assembled inside the cells. Special care w as taken to avoid spread of contamination in the cells, where ''CORA'' installation activities will start in the next years, during the dismantling process The analysis of data and results collected during the dismantling of the first cell shows that direct dismantling can be achieved with careful choice of tools, procedures and techniques, to reduce volumes of wastes to be disposed and radiological burden

Evaluation of Kola-Pod Husk Meal in Broiler Finisher Diets ...

African Journals Online (AJOL)

Nigeria is the world's largest producer of kola nut. The pod husk, which constitutes over 50% of the kola fruit, has been a farm waste to date. Its crude protein content which is similar to that of maize suggests that it is possible to partially replace maize with pod husk meal (KPHM) in broiler finisher diets. In this study, KPHM ...

46 CFR 116.422 - Ceilings, linings, trim, interior finish and decorations.

Science.gov (United States)

2010-10-01

... specified by the Commandant; or (2) Listed by Underwriters Laboratories, does not exceed 2 millimeters (.075...) or UL 723 by an independent laboratory. (c) Bulkheads, linings, and ceilings in high risk... reasonable number of coats of paint or with a marine finish meeting the requirements of § 164.012 in...

Development of antibiotic resistance and up-regulation of the antimutator gene pfpI in mutator Pseudomonas aeruginosa due to inactivation of two DNA oxidative repair genes (mutY, mutM)

DEFF Research Database (Denmark)

Mandsberg, Lotte Frigaard; Macia, Maria D.; Bergmann, Kirsten R.

2011-01-01

showed only a fivefold increase, whereas the single mutant PAOMMgm (mutM) showed a nonsignificant increase in MR compared with PAO1 and the single mutants. Mutations in the regulator nfxB leading to hyperexpression of MexCD-OprJ efflux pump were found as the mechanism of resistance to ciprofloxacin....... In this study, we constructed a double mutant in mutY and mutM (PAOMY-Mgm) and characterized the phenotype and the gene expression profile using microarray and RT-PCR. PAOMY-Mgm presented 28-fold increases in MR compared with wild-type reference strain PAO1. In comparison, the PAOMYgm (mutY) single mutant...... in the double mutant. A better fitness of the mutator compared with PAO1 was found in growth competition experiments in the presence of ciprofloxacin at concentrations just below minimal inhibitory concentration. Up-regulation of the antimutator gene pfpI, that has been shown to provide protection to oxidative...

Conservation of filtering in manufacturing systems with unreliable machines and finished goods buffers

Directory of Open Access Journals (Sweden)

Jingshan Li

2006-01-01

nature of manufacturing systems, this law offers a tool for selecting the smallest, that is, lean, finished goods buffering, which is necessary and sufficient to ensure the desired level ofcustomer demand satisfaction.

The performance of broiler finisher birds fed varying levels of feather ...

African Journals Online (AJOL)

The performance of broiler finisher birds fed varying levels of feather meal as replacement for soya bean meal. ... meal increased, feed cost/ kg weight gain increased and both differed significantly (P<0.05) between treatment means, while the birds tolerated feather meal up to 7.5% inclusion level, 2.5% was the optimal.

Gait-related intrinsic risk factors for patellofemoral pain in novice recreational runners.

Science.gov (United States)

Thijs, Y; De Clercq, D; Roosen, P; Witvrouw, E

2008-06-01

To determine prospectively gait-related intrinsic risk factors for patellofemoral pain (PFP) in a population of novice recreational runners. Prospective cohort study. 102 novice recreational runners (89 women) with no history of knee or lower leg complaints. The standing foot posture of the subjects was examined and plantar pressure measurements during running were collected. The subjects then participated in a 10-week "start to run" programme. During this period all sports injuries were registered by a sports medicine physician. The relationship between the standing foot posture and PFP was investigated and gait-related intrinsic risk factors for PFP were determined. The 17 runners who developed PFP exerted a significantly higher vertical peak force underneath the lateral heel and metatarsals 2 and 3. Logistic regression analysis showed that a significantly higher vertical peak force underneath the second metatarsal and shorter time to the vertical peak force underneath the lateral heel were predictors for PFP. No significant evidence was found for an association between an excessively pronated or supinated foot posture and the development of PFP. The findings suggest that an excessive impact shock during heel strike and at the propulsion phase of running may contribute to an increased risk of developing PFP. The hypothesis that persons at risk for PFP show an altered static foot posture in comparison with non-afflicted persons is not supported by the results of this study.

40 CFR Table 2 to Subpart Tttt of... - Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 2 Table 2 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in § 63.5450, you must meet...

Effect finishing and polishing procedures on the surface roughness of IPS Empress 2 ceramic.

Science.gov (United States)

Boaventura, Juliana Maria Capelozza; Nishida, Rodrigo; Elossais, André Afif; Lima, Darlon Martins; Reis, José Mauricio Santos Nunes; Campos, Edson Alves; de Andrade, Marcelo Ferrarezi

2013-01-01

To evaluate the surface roughness of IPS Empress 2 ceramic when treated with different finishing/polishing protocols. Sixteen specimens of IPS Empress 2 ceramic were made from wax patterns obtained using a stainless steel split mold. The specimens were glazed (Stage 0-S0, control) and divided into two groups. The specimens in Group 1 (G1) were finished/polished with a KG Sorensen diamond point (S1), followed by KG Sorensen siliconized points (S2) and final polishing with diamond polish paste (S3). In Group 2 (G2), the specimens were finished/polished using a Shofu diamond point (S1), as well as Shofu siliconized points (S2) and final polishing was performed using Porcelize paste (S3). After glazing (S0) and following each polishing procedure (S1, S2 or S3), the surface roughness was measured using TALYSURF Series 2. The average surface roughness results were analyzed using ANOVA followed by Tukey post-hoc tests (α = 0.01) RESULTS: All of the polishing procedures yielded higher surface roughness values when compared to the control group (S0). S3 yielded lower surface roughness values when compared to S1 and S2. The proposed treatments negatively affected the surface roughness of the glazed IPS Empress 2 ceramic.

40 CFR Table 1 to Subpart Tttt of... - Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 1 Table 1 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in §§ 63.5305 and 63.5340(b...

The potential of three different PCR-related approaches for the authentication of mixtures of herbal substances and finished herbal medicinal products.

Science.gov (United States)

Doganay-Knapp, Kirsten; Orland, Annika; König, Gabriele M; Knöss, Werner

2018-04-01

Herbal substances and preparations thereof play an important role in healthcare systems worldwide. Due to the variety of these products regarding origin, composition and processing procedures, appropriate methodologies for quality assessment need to be considered. A majority of herbal substances is administered as multicomponent mixtures, especially in the field of Traditional Chinese Medicine and ayurvedic medicine, but also in finished medicinal products. Quality assessment of complex mixtures of herbal substances with conventional methods is challenging. Thus, emphasis of the present work was directed on the development of complementary methods to elucidate the composition of mixtures of herbal substances and finished herbal medicinal products. An indispensable prerequisite for the safe and effective use of herbal medicines is the unequivocal authentication of the medicinal plants used therein. In this context, we investigated the potential of three different PCR-related methods in the characterization and authentication of herbal substances. A multiplex PCR assay and a quantitative PCR (qPCR) assay were established to analyze defined mixtures of the herbal substances Quercus cortex, Juglandis folium, Aristolochiae herba, Matricariae flos and Salviae miltiorrhizae radix et rhizoma and a finished herbal medicinal product. Furthermore, a standard cloning approach using universal primers targeting the ITS region was established in order to allow the investigation of herbal mixtures with unknown content. The cloning approach had some limitations regarding the detection/recovery of the components in defined mixtures of herbal substances, but the complementary use of two sets of universal primer pairs increased the detection of components out of the mixture. While the multiplex PCR did not retrace all components in the defined mixtures of herbal substances, the established qPCR resulted in simultaneous and specific detection of the five target sequences in all defined

Factors affecting the daily feed intake and feed conversion ratio of pigs in grow-finishing units: the case of a company.

Science.gov (United States)

Pierozan, C R; Agostini, P S; Gasa, J; Novais, A K; Dias, C P; Santos, R S K; Pereira, M; Nagi, J G; Alves, J B; Silva, C A

2016-01-01

The aim of this study was to use mathematical modeling to identify and quantify the main factors that affect daily feed intake (DFI) and feed conversion ratio (FCR) in grow-finishing (GF) pig units. We evaluated the production records of 93 GF farms between 2010 and 2013, linked to a company, working in a cooperative system, located in western Paraná State, Brazil. A total of 683 batches, consisting of approximately 495,000 animals, were used. Forty production factors related to the management, health, plant and equipment, nutrition, genetics and environment were considered. The number of pigs per pen, type of feeder, origin and sex (the last two variables were combined in the models) of the animals and initial and final body weights were included in the final models to predict DFI and FCR (dependent variables). Additionally, the duration of the GF phase was included for the parameter FCR. All factors included in the final models had significant effects for both dependent variables. There was a reduction in DFI (0.04 kg) (P units specialized for producing piglets (SPU) had higher DFI (approximately 0.02 kg) (P < 0.01) than batches of females and batches of mixed animals from SPU, and batches of mixed animals from farms not specialized for piglet production (farrow-to-finish farms). Batches of females from SPU and mixed batches from SPU had better FCR (5.0 and 3.0 points respectively) (P < 0.001 and P < 0.001, respectively) than batches of piglets originating from farrow-to-finish farms. The variables selected for the final models explained approximately 50 and 64 % of the total variance in DFI and FCR, respectively. The models are tools for the interpretation of the factors related to the evaluated parameters, aiding in the identification of critical aspects of production. The main parameters affecting DFI and FCR in this company during the GF period were the number of pigs per pen, the type of feeder used and the combination origin-sex of the

Microgel-based surface modifying system for stimuli-responsive functional finishing of cotton

NARCIS (Netherlands)

Kulkarni, A.N.; Tourrette, A.; Warmoeskerken, Marinus; Jocic, D.

2010-01-01

An innovative strategy for functional finishing of textile materials is based on the incorporation of a thin layer of surface modifying systems (SMS) in the form of stimuli-sensitive microgels or hydrogels. Since the copolymerization of poly(N-isopropylacrylamide) with an ionizable polymer, such as

A parametric study on the use of passive fire protection in FPSO topside module

Directory of Open Access Journals (Sweden)

Martin Friebe

2014-12-01

Full Text Available Fire is a continuous threat to FPSO topside modules as large amounts of oil and gas are passing through the modules. As a conventional measure to mitigate structural failure under fire, passive fire protection (PFP coatings are widely used on main structural members. However, an excessive use of PFP coatings can cause considerable cost for material purchase, installation, inspection and maintenance. Long installation time can be a risk since the work should be done nearly at the last fabrication stage. Thus, the minimal use of PFP can be beneficial to the reduction of construction cost and the avoidance of schedule delay. This paper presents a few case studies on how different applications of PFP have influence on collapse time of a FPSO module structure. A series of heat analysis and thermal elasto-plastic FE analysis are performed for different PFP coatings and the resultant collapse time and the amount of PFP coatings are compared with each other.

Comparison of vitality states of finishers and withdrawers in trail running: An enactive and phenomenological perspective.

Directory of Open Access Journals (Sweden)

Nadège Rochat

Full Text Available Studies on ultra-endurance suggest that during the races, athletes typically experience three vitality states (i.e., preservation, loss, and revival at the phenomenological level. Nevertheless, how these states contribute to the management and outcome of performance remains unclear. The aim of this study was to determine whether and how the vitality states experienced by runners and their evolution during a trail race can be used to distinguish finishers from withdrawers. From an enactive and phenomenological framework, we processed enactive interviews and blog posts of race narratives. We distinguished units of meaning, which were grouped into sequences of experience; each sequence was then categorized as one of the three vitality states: state of vitality preservation (SVP, state of vitality loss (SVL or state of vitality revival (SVR. We analyzed the distribution of these vitality states and their temporal organization at the beginning, in the second and third quarters, and at the end of the races, and we qualitatively characterized runners' adaptations to SVL. Results showed that finishers completed the race in SVP, with overall significantly more sequences in SVP and significantly fewer sequences in SVL than withdrawers. SVR did not discriminate finishers from withdrawers. The temporal organization of the vitality states showed a significant difference in the emergence of SVP from the second quarter of the race, as well as a significant difference in the emergence of SVL from the third quarter of the race. The analysis of adaptations to SVL confirmed that finishers were more capable of exiting SVL by enacting a preservation world when they felt physical or psychological alerts, whereas withdrawers remained in SVL. Our results showed that finishers and withdrawers did not enact the same phenomenological worlds in the race situation, especially in the organization of vitality adaptations and their relationships to difficulties; the cumulative

Appearance of anodised aluminium: Effect of alloy composition and prior surface finish

DEFF Research Database (Denmark)

Aggerbeck, Martin; Canulescu, Stela; Dirscherl, Kai

2014-01-01

Effect of alloy composition and prior surface finish on the optical appearance of the anodised layer on aluminium alloys was investigated. Four commercial alloys namely AA1050, Peraluman 706, AA5754, and AA6082 were used for the investigation. Microstructure and surface morphology of the substrat...

Pulsed-field profile diversities of Salmonella Enteritidis, S. Infantis, and S. Corvallis in Japan

Directory of Open Access Journals (Sweden)

Koichi Murakami

2017-10-01

Full Text Available The diversity of pulsed-field profiles (PFPs within non-typhoidal Salmonella subtypes influences epidemiological analyses of Salmonella outbreaks. Therefore, determining the PFP diversity of each Salmonella serovar is important when evaluating current circulating strains. This study examined the PFP diversity of three important public health Salmonella enterica subspecies enterica serovars, S. Enteritidis (n=177, S. Infantis (n=205, and S. Corvallis (n=90, using pulsed-field gel electrophoresis. Isolates were collected from several sources, primarily from chicken-derived samples, in the Kyushu-Okinawa region of Japan between 1989 and 2005. S. Enteritidis isolates displayed 51 distinct PFPs (E-PFPs, with 92 (52.0% and 32 (18.1% isolates displaying types EPFP1 and E-PFP10, respectively. The 205 S. Infantis isolates showed 54 distinct PFPs (I-PFPs, with 87 (42.4% and 36 (17.6% isolates being I-PFP4 and I-PFP2, respectively. I-PFP18 was the dominant I-PFP of layer chicken isolates across a 5-year period. Fourteen distinct S. Corvallis PFPs were detected. Simpson’s index results for the genetic diversities of S. Enteritidis, S. Infantis, and S. Corvallis isolates were 0.70, 0.79, and 0.78, respectively. None of the EPFPs or I-PFPs of layer chicken isolates overlapped with those of broiler chicken isolates, and the dominant clonal lines existed for >10 years. In conclusion, limited PFP diversities were detected amongst S. Enteritidis, S. Infantis, and S. Corvallis isolates of primarily chicken-derived origins in the Kyushu-Okinawa region of Japan. Therefore, it is important to take into account these limitations in PFP diversities in epidemiological analyses of Salmonella outbreaks.

Finishing of the cold mass assembly

CERN Multimedia

Maximilien Brice

2001-01-01

Photo 1 The connection-side end of the active part assembly. This view shows the electrical connections between the poles and the curved bus ended with flanges for the connection with the protection diode. Photo 2 The connection-side end of the active part assembly. This view shows the electrical connections between the poles, the auxiliary bus bars and the instrumentation wires. Photo 3 Lyre-side end of the active part assembly. One can see the mechanical support of the corretor magnets that are to be installed around the cold bore tubes. Photo 4 General view of the finishing station showing the special supporting structures (blue and yellow structures) needed for the geometric measurements and for the alignment operations. Around the magnet, there are datum points (on the tripodes) needed to build up the coordinates system for the measurements.

Optimizing Organophosphorus Fire Resistant Finish for Cotton Fabric Using Box-Behnken Design

International Nuclear Information System (INIS)

Sohail, Y.; Parag, B.; Nemeshwaree, B.; Giorgio, R.

2016-01-01

N-methylol dimethyl phosphono propionamide (MDPA) is one of the most utilized fire resistant (FR) finishes for cotton fabrics, utilized as part of a formulation with trimethylol melamine (TMM) to acquire better crosslinking and enhanced FR properties. The system parameters of the finishing treatment were upgraded for better FR properties and low mechanical loss to the fabric by the response surface methodology utilizing Box-Behnken statistical designed experimental strategy. The impacts of concentration on the cotton fabric’s properties (fire resistance and mechanical properties) were assessed with the regression equations. The optimum conditions by predicting the FR reagents focusing intact mechanical properties of the fabric were additionally studied. It was found that the parameters of crosslinking agents in the FR formulation have a prime role in the general FR properties of the cotton fabrics. The R-squared estimations of the considerable number of responses were above 92%, demonstrating the level of relationship between the predicted values by the Box-Behnken frameworks and the real test results.

ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

Directory of Open Access Journals (Sweden)

Nyembwe, K.

2012-11-01

Full Text Available In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP sand moulds is undertaken. A case study from a local tool room, dealing with the manufacturing of an aluminium die for the lost wax process, is employed. Modern techniques, including surface roughness analysis and three dimensional scanning, are used to determine and understand how each manufacturing step influences the final quality of the cast tool. The best surface finish obtained for the cast die had arithmetic average roughness (Ra and mean average roughness (Rz respectively equal to 3.23m and 11.38m. In terms of dimensional accuracy, 82% of cast-die points coincided with the Computer Aided Design (CAD data, which is within the typical tolerances of sand cast products. The investigation shows that mould coating contributes slightly to the improvement of the cast tool surface finish. The study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. These findings indicate that machining will always be required to improve the surface finish and the dimensional accuracy of cast tools in RP sand moulds.

Construction of Industrial Electron Beam Plant for Wastewater Treatment

International Nuclear Information System (INIS)

Han, B.; Kim, J.; Kim, Y.; Kim, S.; Lee, M.; Choi, J.; Ahn, S.; Makarov, I.E.; Ponomarev, A.V.

2004-01-01

A pilot plant for treating 1,000 m3/day of dyeing wastewater with e-beam has been constructed and operated since 1998 in Daegu, Korea together with the biological treatment facility. The wastewater from various stages of the existing purification process has been treated with electron beam in this plant, and it gave rise to elaborate the optimal technology of the electron beam treatment of wastewater with increased reliability at instant changes in the composition of wastewater. Installation of the e-beam pilot plant resulted in decolorizing and destructive oxidation of organic impurities in wastewater, appreciable to reduction of chemical reagent consumption, in reduction of the treatment time, and in increase in flow rate limit of existing facilities by 30-40%. Industrial plant for treating 10,000 m3/day, based upon the pilot experimental result, is under construction and will be finished by 2005. This project is supported by the International Atomic Energy Agency (IAEA) and Korean Government

Inspection of panel paintings beneath gilded finishes using terahertz time-domain imaging

DEFF Research Database (Denmark)

Dandolo, Corinna Ludovica Koch; Cosentino, Antonino; Jepsen, Peter Uhd

2014-01-01

the transmission of electromagnetic waves through metallic films. Therefore, imaging of subsurface features below gilded finishes may be regarded as Very challenging. A small but non-negligible direct transmission through metal films occurs if the film thickness is of the order of the skin depth of the metal...

Effects of the truth FinishIt brand on tobacco outcomes.

Science.gov (United States)

Evans, W Douglas; Rath, Jessica M; Hair, Elizabeth C; Snider, Jeremy Williams; Pitzer, Lindsay; Greenberg, Marisa; Xiao, Haijun; Cantrell, Jennifer; Vallone, Donna

2018-03-01

Since 2000, the truth campaign has grown as a social marketing brand. Back then, truth employed branding to compete directly with the tobacco industry. In 2014, the launch of truth FinishIt reflected changes in the brand's strategy, the tobacco control environment, and youth/young adult behavior. Building on a previous validation study, the current study examined brand equity in truth FinishIt , as measured by validated multi-dimensional scales, and tobacco related attitudes, beliefs, and behavior based on two waves of the Truth Longitudinal Cohort data from 2015 and 2016. A fixed effects logistic regression was used to estimate the change in brand equity between panel survey waves 3 and 4 on past 30-day smoking among ever and current smokers. Additional models determined the effects of brand equity predicting tobacco attitudes/use at follow up among the full sample. All analyses controlled for demographic factors. A one-point increase in the brand equity scale between the two waves was associated with a 66% greater chance of not smoking among ever smokers (OR 1.66, CI 1.11-2.48, p  effects of brand equity on tobacco use and how tobacco control can optimize the use of branding in campaigns.

TECHNOLOGY FORMING PRICE DISTRIBUTION OF FINISHED GOODS OF LOGISTICS SYSTEM

Directory of Open Access Journals (Sweden)

Novikova T. V.

2015-12-01

Full Text Available Modern economics has developed a number of areas of the system for controlling the distribution of finished products. However, in domestic and foreign economic literature the mechanisms of logistics approach are not sufficient to provide higher sales of enterprise-producers, that have sales in remote areas. In this study, first, the importance of company-producers and end-users the methods of rational delivery of finished products is considered, and secondly, the approaches to defining the essence and content of the concept of «distribution» are given, in the third, the logistics processes of the distribution system ready products of a particular company-producer are described, fourthly, the technology of one price product delivery was developed and it was shown the economic efficiency (the possible results of the solution of the problem of distribution logistics of its application in the target company. The study showed that there is an opportunity, based on the development and implementation of technologies to reduce the final price of the goods, to develop the company and increase its competitiveness by minimizing costs and increasing return on investment. The results of research extend the knowledge of methodology of system logistics management in the enterprise.