WorldWideScience

Sample records for fine powder-like solid

  1. A New Fine Damping Method for Solid ESG Rotor

    Institute of Scientific and Technical Information of China (English)

    LIU Chun-ning; TIAN Wei-feng; JIN Zhi-hua

    2006-01-01

    For the electrostatically suspended gyro(ESG) with solid rotor, because the equatorial photoelectric sensor won't sense the equatorial marking line and output the correct damping control information when the nutation angle is small, the active damping with equatorial marking line will bring considerable error. The passive damping method by applying strong DC magnetic field requires too much time. So an active damping method by longitude marking lines is proposed to fulfill the fine damping for solid ESG rotor. The shape of rotor marking lines and the principle of fine damping are introduced. The simulation results prove that this fine damping method can effectively solve the problem of damping error introduced by active damping with equatorial marking line. The estimating results for damping time indicate that the fine damping time is less than 10 percent of passive damping time.

  2. Characterization of Ultra Fine Solids(BS) in Athabasca Bitumen

    Institute of Scientific and Technical Information of China (English)

    LI Zai-Feng(李再峰); Judy KUNG; TU Yun(涂云); Luba S.KOTLYAR; Keng H.CHUNG

    2004-01-01

    The ultra fine (<200 nm) inorganic solids (BS) were separated from bitumen which was washed by toluene and centrifugated at 2000 rpm.The result of PAS FTIR and image of TEM showed that the structure of BS particles was smiliar to that of kaolinite clay.On the surface of BS,both toluene insoluble organic matter and structural OH group are detected at the same time.The surface characteristics imparted a bi-wettable nature to the BS.As a result,the BS is able to stabilize fine water emulsion in the bitumen phase.The organic matter associated with BS is a possible factor of the fouling on catalyst and equipment.

  3. Dynamics of fine particles in liquid-solid fluidized beds

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    On the basis of the Local Equilibrium Model (LEM), fine particles with large Richardson-Zaki exponent n show, under certain conditions during bed expansion and collapse, different dynamic behavior from particles with small n. For an expansion process there may be a concentration discontinuity propagating upward from the distributor, and, on the contrary, for a collapse process there may be a progressively broadening and upward-propagating continuous transition zone instead of discontinuity. The predictions of the bed height variation and the discontinuity trace have been validated experimentally.

  4. Preparation of semi-solid slurry containing fine and globular particles for wrought aluminum alloy 2024

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The semi-solid slurry of wrought aluminum alloy 2024 was prepared by a well developed rheocasting process, low superheat pouring with shearing field(LSPSF). The appreciate combination of pouring temperature and rotation speed of barrel, can give rise to a transition of the growth morphology of primary α(Al) from coarse-dendritic to coarse-particle-like and further to fine-globular. The combined effects of both localized rapid cooling and vigorous mixing during the initial stage of solidification can enhance wall nucleation and nuclei survival, which leads to the formation of fine-globular primary α(Al). By using semi-solid slurry prepared by LSPSF, direct squeeze cast cup-shaped component with improved mechanical properties such as yield strength of 198MPa, ultimate tensile strength of 306 MPa and elongation of 10.4%, can be obtained.

  5. Experimental study on the interaction of fine water mist with solid pool fires

    Institute of Scientific and Technical Information of China (English)

    LIU; Jianghong; (刘江虹); LIAO; Guangxuan; (廖光煊); LI; Peide; (厉培德); QIN; Jun; (秦俊); LU; Xiyun; (陆夕云)

    2003-01-01

    This paper describes experimental study of the interaction of fine water mists with solid pool fires. Fine water mist was generated by a single pressure nozzle and solid pool fires were produced from solid red pine or polymethyl methacrylate(PMMA). The LDV/APV system was employed to determine the water mist characteristics. The water mist droplet sizes and velocities from the nozzle were measured under varying conditions and at different locations. The effects of solid type, water flow rate, and nozzle distance from the sample surface on extinguishments time were examined. At a given water flow rate, the extinguishment time is much longer for PMMA fires than for solid pine fires. The extinguishment time was found to decrease with increasing water flow rate. At very low water flow, the extinguishment time decreases when the nozzle is positioned further from the sample surface. On the contrary, at high water flow, the extinguishment time appears to be independent of the distance between the nozzle and the sample surface. The experimental results show that flame extinguishments is due primarily to fuel surface cooling and wetting.

  6. Solid hydrocarbon: a migration-of-fines problem in carbonate reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Lomando, A.J.

    1986-05-01

    The most familiar example of a migration-of-fines problem is authigenic kaolinite, which can detach, migrate through a pore system, and bridge pore throats, thus reducing permeability. under certain conditions, a similar problem is caused by solid hydrocarbon, independent of a mode of origin, which has precipitated in carbonate pore systems. Cores from several reservoirs in the Lower Cretaceous of east Texas were used as the data base in this study. Three morphotypes of solid hydrocarbon have been identified from thin-section and scanning electron microscope observations: droplets, peanut brittle, and carpets. Droplets are small, individual, rounded particles scattered on pore walls. Peanut brittle ranges from a continuous to discontinuous thin coating with random rounded lumps that probably have droplet precursors. Carpets are thick, continuous coatings and, at the extreme, can effectively occlude whole pores. Initially, solid hydrocarbon reduces permeability without necessarily decreasing porosity significantly. Likewise, solid hydrocarbon cannot be detected directly from wireline logs. Acidizing to enhance communication to the well bore is a common completion procedure in limestone and calcareous sandstone reservoirs. In reservoirs containing solid hydrocarbon, acid etches the substrate and releases solid hydrocarbon, which migrates in the pore system and bridges pore throats. Differential well-bore pressure also may cause solid hydrocarbon to migrate. Therefore, wettability, which controls hydrocarbon adhesion to the pore walls, and the dominant morphotype are important factors in the extent of reservoir damage.

  7. Formation of Splats from Suspension Particles with Solid Inclusions Finely Dispersed in a Melted Metal Matrix

    Science.gov (United States)

    Solonenko, O. P.

    2012-12-01

    A theoretical model has been developed to describe the splats formation from composite particles of several tens of micrometers in size whose liquid metal binder contains a high volume concentration of ultra-fine refractory solid inclusions uniformly distributed in the binder. A theoretical solution was derived, enabling evaluation of splat thickness and diameter, and also the contact temperature at the particle-substrate interface, under complete control of key physical parameters (KPPs) of the spray process (impact velocity, temperature, and size of the particle, and substrate temperature) versus the concentration of solid inclusions suspended in the metal-binder melt. Using the solution obtained, the calculations performed demonstrate the possibility of formulating adequate requirements on the KPPs of particle-substrate interaction providing a deposition of ceramic-metal coatings with predictable splat thickness and degree of particle flattening on the substrate, and also with desired contact temperature during the formation of the first coating monolayer.

  8. Fine grain separation for the production of biomass fuel from mixed municipal solid waste.

    Science.gov (United States)

    Giani, H; Borchers, B; Kaufeld, S; Feil, A; Pretz, T

    2016-01-01

    The main goal of the project MARSS (Material Advanced Sustainable Systems) is to build a demonstration plant in order to recover a renewable biomass fuel suitable for the use in biomass power plants out of mixed municipal solid waste (MMSW). The demonstration plant was constructed in Mertesdorf (Germany), working alongside an existing mechanical-biological treatment plant, where the MMSW is biological dried under aerobe conditions in rotting boxes. The focus of the presented sorting campaign was set on the processing of fine grain particles minor than 11.5mm which have the highest mass content and biogenic energy potential of the utilized grain size fractions. The objective was to produce a biomass fuel with a high calorific value and a low content of fossil (plastic, synthetic) materials while maximizing the mass recovery. Therefore, the biogenic components of the dried MMSW are separated from inert and fossil components through various classification and sifting processes. In three experimental process setups of different processing depths, the grain size fraction 4-11.5mm was sifted by the use of air sifters and air tables.

  9. Colloidal interactions between Langmuir-Blodgett bitumen films and fine solid particles.

    Science.gov (United States)

    Long, Jun; Zhang, Liyan; Xu, Zhenghe; Masliyah, Jacob H

    2006-10-10

    In oil sand processing, accumulation of surface-active compounds at various interfaces imposes a significant impact on bitumen recovery and bitumen froth cleaning (i.e., froth treatment) by altering the interfacial properties and colloidal interactions among various oil sand components. In the present study, bitumen films were prepared at toluene/water interfaces using a Langmuir-Blodgett (LB) upstroke deposition technique. The surface of the prepared LB bitumen films was found to be hydrophobic, comprised of wormlike aggregates containing a relatively high content of oxygen, sulfur, and nitrogen, indicating an accumulation of surface-active compounds in the films. Using an atomic force microscope, colloidal interactions between the LB bitumen films and fine solids (model silica particles and clay particles chosen directly from an oil sand tailing stream) were measured in industrial plant process water and compared with those measured in simple electrolyte solutions of controlled pH and divalent cation concentrations. The results show a stronger long-range repulsive force and weaker adhesion force in solutions of higher pH and lower divalent cation concentration. In plant process water, a moderate long-range repulsive force and weak adhesion were measured despite its high electrolyte content. These findings provide more insight into the mechanisms of bitumen extraction and froth treatment.

  10. Amorphous solid dispersion of cyclosporine A prepared with fine droplet drying process: Physicochemical and pharmacokinetic characterization.

    Science.gov (United States)

    Suzuki, Hiroki; Moritani, Tatsuru; Morinaga, Tadahiko; Seto, Yoshiki; Sato, Hideyuki; Onoue, Satomi

    2017-03-15

    The present study aimed to develop an amorphous solid dispersion (ASD) of cyclosporine A (CsA) by a fine droplet drying (FDD) process for improvement in oral absorption of CsA. CsA and hydroxypropyl cellulose-SSL were dissolved in 1,4-dioxane, and the solution was powdered by the FDD process to obtain the ASD formulation of CsA (ASD/CsA). The ASD/CsA was characterized in terms of morphology, particle size distribution, crystallinity, dissolution behavior, physicochemical stability, and pharmacokinetic behavior in rats. The ASD/CsA was obtained in the form of uniform spherical particles, and the span factor was calculated to be ca. 0.4. CsA in the formulation existed in an amorphous state. The ASD/CsA exhibited a higher dissolution behavior of CsA than amorphous CsA, whereas storage of the ASD/CsA under accelerated conditions led to impairment in the dissolution behavior. The constant release of CsA from non-aged ASD/CsA was observed during dissolution testing. After oral administration of CsA samples (10mg-CsA/kg) in rats, the ASD/CsA showed a high and sustained plasma concentration of CsA as evidenced by a 18-fold increase in the oral bioavailability of CsA compared with amorphous CsA. From these findings, the FDD process might be an efficacious option for the ASD formulation of CsA with enhanced biopharmaceutics properties. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Insights into metals in individual fine particles from municipal solid waste using synchrotron radiation-based micro-analytical techniques

    Institute of Scientific and Technical Information of China (English)

    Yumin Zhu; Hua Zhang; Liming Shao; Pinjing He

    2015-01-01

    Excessive inter-contamination with heavy metals hampers the application of biological treatment products derived from mixed or mechanically-sorted municipal solid waste (MSW).In this study,we investigated fine particles of <2 mm,which are small fractions in MSW but constitute a significant component of the total heavy metal content,using bulk detection techniques.A total of 17 individual fine particles were evaluated using synchrotron radiation-based micro-X-ray fluorescence and micro-X-ray diffraction.We also discussed the association,speciation and source apportionment of heavy metals.Metals were found to exist in a diffuse distribution with heterogeneous intensities and intense hot-spots of <10 μm within the fine particles.Zn-Cu,Pb-Fe and Fe-Mn-Cr had significant correlations in terms of spatial distribution.The overlapped enrichment,spatial association,and the mineral phases of metals revealed the potential sources of fine particles from size-reduced waste fractions (such as scraps of organic wastes or ceramics) or from the importation of other particles.The diverse sources of heavy metal pollutants within the fine particles suggested that separate collection and treatment of the biodegradable waste fraction (such as food waste) is a preferable means of facilitating the beneficial utilization of the stabilized products.

  12. Insights into metals in individual fine particles from municipal solid waste using synchrotron radiation-based micro-analytical techniques.

    Science.gov (United States)

    Zhu, Yumin; Zhang, Hua; Shao, Liming; He, Pinjing

    2015-01-01

    Excessive inter-contamination with heavy metals hampers the application of biological treatment products derived from mixed or mechanically-sorted municipal solid waste (MSW). In this study, we investigated fine particles of radiation-based micro-X-ray fluorescence and micro-X-ray diffraction. We also discussed the association, speciation and source apportionment of heavy metals. Metals were found to exist in a diffuse distribution with heterogeneous intensities and intense hot-spots of waste fractions (such as scraps of organic wastes or ceramics) or from the importation of other particles. The diverse sources of heavy metal pollutants within the fine particles suggested that separate collection and treatment of the biodegradable waste fraction (such as food waste) is a preferable means of facilitating the beneficial utilization of the stabilized products.

  13. Contrast-enhanced harmonic endoscopic ultrasound-guided fine-needle aspiration in the diagnosis of solid pancreatic lesions: a retrospective study.

    Science.gov (United States)

    Hou, Xiaojia; Jin, Zhendong; Xu, Can; Zhang, Minmin; Zhu, Jianwei; Jiang, Fei; Li, Zhaoshen

    2015-01-01

    The negative predictive value of endoscopic ultrasonography-guided fine needle aspiration for the diagnosis of solid pancreatic lesions remains low, and the biopsy specimens are sometimes inadequate for appropriate pathological diagnosis. To evaluate the usefulness of a novel method of contrast-enhanced harmonic endoscopic ultrasonography-guided fine-needle aspiration for the differential diagnosis and adequate sampling of solid pancreatic lesions. Patients with a diagnosis of solid pancreatic lesions who underwent fine-needle aspiration guided by contrast-enhanced harmonic endoscopic ultrasonography or by endoscopic ultrasonography from October 2010 to July 2013 were retrospectively identified and classified into the CH-EUS or EUS group, respectively. Surgical pathology and/or follow-up results were defined as the final diagnosis. Operating characteristics and adequacy of biopsy specimens by fine-needle aspiration were compared between the two groups. Operating characteristics for contrast-enhanced harmonic endoscopic ultrasonography-guided fine-needle aspiration in solid pancreatic lesions were as follows: area under the curve = 0.908, sensitivity = 81.6%, specificity = 100%, positive predictive value = 100%, negative predictive value = 74.1%, and accuracy = 87.9%. The percentage of adequate biopsy specimens in the CH-EUS group (96.6%) was greater than that in the EUS group (86.7%). Simultaneous contrast-enhanced harmonic endoscopic ultrasonography during fine-needle aspiration is useful for improving the diagnostic yield and adequate sampling of solid pancreatic lesions.

  14. Effect of fine solid particles on absorption rate of gaseous CO2

    Institute of Scientific and Technical Information of China (English)

    Sumin LU; Youguang MA; Shuhua SHEN; Chunying ZHU

    2008-01-01

    The influence of the properties of solid particles in slurry on the absorption of CO2 in the slurry was inves-tigated in a stirred thermostatic reactor. The absorption experiments were carried out in three different slurries con-sisting of water, cyclohexane and soybean oil, respectively, and three kinds of solid particles (active carbon, active alu-mina and silica gel) were incorporated into each of the above mentioned slurries separately. The experimental results show that the active carbon particles could enhance the absorption rate of gaseous CO2 in the aqueous slurry, while in the cyclohexane slurry, active carbon particles indi-cated no the absorption enhancement effect. However, it was observed that the active alumina and silica gel particles could enhance the absorption rate of CO2 in the cyclohex-ane slurry. These phenomena indicate that the solid part-icles, which could enhance the gaseous CO2 absorption rate, should possess two properties simultaneously, i.e. they rejected the solvent and had higher adsorption capacity for the solute. The experimental results also show that, as for those solid particles which could enhance the gas absorption rate, the enhancement increased quickly with the increase of solid concentration in slurry at first, and then reached a constant value gradually. It was also found that the enhancement factor was related to the coverage fraction of solid particles on the gas-liquid interface, and due to the reduction of surface fraction with increasing stirred speed, the enhancement factor decreased.

  15. Comparing endoscopic ultrasound (EUS)-guided fine needle aspiration (FNA) versus fine needle biopsy (FNB) in the diagnosis of solid lesions: study protocol for a randomized controlled trial.

    Science.gov (United States)

    Wang, Jinlin; Wu, Xiaoli; Yin, Ping; Guo, Qiaozhen; Hou, Wei; Li, Yawen; Wang, Yun; Cheng, Bin

    2016-04-12

    Linear endoscopic ultrasonography (EUS) allows the visualization, identification, and characterization of the extent of lesions of the gastrointestinal (GI) tract and adjacent structures. EUS-guided fine-needle aspiration (EUS-FNA) facilitates a more accurate diagnosis of mediastinal, intra-abdominal, and pancreatic lesions through the collection of the cytological material under direct visualization. Recent reports suggest that histological samples can be obtained by EUS-FNA with a reverse, bevel-tipped needle (the ProCore needle) to collect the core samples (fine needle biopsy, FNB), thereby adding a new dimension to the diagnostic usefulness of this technique. Certain neoplasms, such as lymphoma and stromal tumors, can be assessed by EUS-FNB to confirm the diagnosis. Here, we aimed to carry out a prospective, multicenter, single-blind, randomized, controlled trial to compare EUS-FNB and EUS-FNA. A total of 408 patients will be enrolled from five endoscopic centers. Patients will be divided into two groups: (1) group A, which is the EUS regular needle group (EUS-FNA) and (2) group B, which is the EUS ProCore needle group (EUS-FNB). Patients in group A will be examined with a 22G EchoTip Ultra needle, and patients in group B, with a 22G EchoTip ProCore needle. For all included patients, four EUS-guided passes will be made in each lesion. In the first and second pass, a slow-pull suction method of the stylet will be done. The third and fourth pass will use manual suction of 5 cc. The primary objective is to compare the diagnostic yield of malignancy by EUS-FNA versus EUS-FNB. The trial will compare samples obtained by EUS-FNA versus EUS-FNB for the diagnostic yield of solid lesions. The efficacy of these two sampling methods will be assessed on various lesions, which may provide insights into developing practice guidelines for their future indications. Clinical Trials.gov, NCT02327065 .

  16. Slow pull versus suction in endoscopic ultrasound-guided fine-needle aspiration of pancreatic solid masses.

    Science.gov (United States)

    Nakai, Yousuke; Isayama, Hiroyuki; Chang, Kenneth J; Yamamoto, Natsuyo; Hamada, Tsuyoshi; Uchino, Rie; Mizuno, Suguru; Miyabayashi, Koji; Yamamoto, Keisuke; Kawakubo, Kazumichi; Kogure, Hirofumi; Sasaki, Takashi; Hirano, Kenji; Tanaka, Mariko; Tada, Minoru; Fukayama, Masashi; Koike, Kazuhiko

    2014-07-01

    Endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) of pancreatic masses is an established procedure for obtaining a pathological specimen. However, application of suction during EUS-FNA is still controversial and the efficacy of the slow-pull technique was recently reported for new core biopsy needles. The purpose of this study was to compare the suction and slow-pull techniques using regular FNA needles. The diagnostic yield of the suction and slow-pull techniques was retrospectively studied for patients who underwent EUS-FNA for pancreatic solid lesions. A total of 367 passes (181 by suction and 186 by the slow-pull technique) were performed during 97 EUS-FNA procedures for 93 patients with pancreatic solid lesions. The slow-pull technique resulted in lower scores for cellularity (≥2 for 37.5 % vs. 76.7 %) but scores for contamination with blood were lower (≥2 for 25.0 % vs. 66.7 %) and sensitivity of diagnosis of malignancy was higher (90.0 % vs. 67.9 %) when a 25-gauge FNA needle was used. There were no significant differences between the two techniques when a 22-gauge needle was used. In multivariate analysis of 82 cases with malignancy, the slow-pull technique (odds ratio (OR) 1.92, P = 0.028), tumor size ≥25 mm (OR 4.64, P suction technique in EUS-FNA of pancreatic solid masses, especially with a 25-gauge FNA needle.

  17. Removal of MBBR Biofilm Solids by Salsnes Filter Fine Mesh Sieves

    OpenAIRE

    Ng, HuaQin

    2012-01-01

    Biological wastewater treatment is often used in conjunction with primary treatment to reduce the constituents in wastewater. It is normally necessary to separate the biomass from the treated wastewater in order to meet the effluent discharge standards. Moving Bed Biofilm Reactor (MBBR) is a biofilm process where plastic carriers carrying the biomass are moving along with the wastewater and typically operating with low concentration of suspended solids in pure biofilm systems. Salsnes Filters...

  18. Fine refinement of solid state structure of racemic form of phospho-tyrosine employing NMR Crystallography approach.

    Science.gov (United States)

    Paluch, Piotr; Pawlak, Tomasz; Oszajca, Marcin; Lasocha, Wieslaw; Potrzebowski, Marek J

    2015-02-01

    We present step by step facets important in NMR Crystallography strategy employing O-phospho-dl-tyrosine as model sample. The significance of three major techniques being components of this approach: solid state NMR (SS NMR), X-ray diffraction of powdered sample (PXRD) and theoretical calculations (Gauge Invariant Projector Augmented Wave; GIPAW) is discussed. Each experimental technique provides different set of structural constraints. From the PXRD measurement the size of the unit cell, space group and roughly refined molecular structure are established. SS NMR provides information about content of crystallographic asymmetric unit, local geometry, molecular motion in the crystal lattice and hydrogen bonding pattern. GIPAW calculations are employed for validation of quality of elucidation and fine refinement of structure. Crystal and molecular structure of O-phospho-dl-tyrosine solved by NMR Crystallography is deposited at Cambridge Crystallographic Data Center under number CCDC 1005924.

  19. EUS-guided 22-gauge fine-needle aspiration versus core biopsy needle in the evaluation of solid pancreatic neoplasms.

    Science.gov (United States)

    Strand, Daniel S; Jeffus, Susanne K; Sauer, Bryan G; Wang, Andrew Y; Stelow, Edward B; Shami, Vanessa M

    2014-09-01

    Endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) is widely used for diagnosis of pancreatic lesions. The Echotip Procore Needle (Wilson-Cook Medical) is a new 22G fine biopsy needle (FNB) for obtaining core biopsy material at time of EUS. This study aimed to compare the technical and diagnostic performance of conventional FNA and FNB. Thirty-two patients met the design criteria for this prospective paired cohort study. All lesions sampled were solid (non-cystic) pancreatic masses by EUS appearance. Patients were randomized to receive FNA or FNB by first attempt. A cytopathologist performed on-site evaluations. Samples were assessed for accuracy of diagnosis, cellularity, contamination, and sufficiency for ancillary studies. Technical and diagnostic performances were compared. Compared to FNA, there was a statistically significant decreased ability of FNB to achieve a diagnosis (FNA 93.8%, FNB 28.1%, P needle. Regarding operator perceived ease-of-use, FNA outperformed FNB (P biopsy needle was not apparent in our series. Additional studies are needed before routine adoption of 22G FNB can be recommended. Copyright © 2014 Wiley Periodicals, Inc.

  20. A LOW COST AND HIGH QUALITY SOLID FUEL FROM BIOMASS AND COAL FINES

    Energy Technology Data Exchange (ETDEWEB)

    John T. Kelly; George Miller; Mehdi Namazian

    2001-07-01

    Use of biomass wastes as fuels in existing boilers would reduce greenhouse gas emissions, SO2 and NOx emissions, while beneficially utilizing wastes. However, the use of biomass has been limited by its low energy content and density, high moisture content, inconsistent configuration and decay characteristics. If biomass is upgraded by conventional methods, the cost of the fuel becomes prohibitive. Altex has identified a process, called the Altex Fuel Pellet (AFP) process, that utilizes a mixture of biomass wastes, including municipal biosolids, and some coal fines, to produce a strong, high energy content, good burning and weather resistant fuel pellet, that is lower in cost than coal. This cost benefit is primarily derived from fees that are collected for accepting municipal biosolids. Besides low cost, the process is also flexible and can incorporate several biomass materials of interest The work reported on herein showed the technical and economic feasibility of the AFP process. Low-cost sawdust wood waste and light fractions of municipal wastes were selected as key biomass wastes to be combined with biosolids and coal fines to produce AFP pellets. The process combines steps of dewatering, pellet extrusion, drying and weatherizing. Prior to pilot-scale tests, bench-scale test equipment was used to produce limited quantities of pellets for characterization. These tests showed which pellet formulations had a high potential. Pilot-scale tests then showed that extremely robust pellets could be produced that have high energy content, good density and adequate weatherability. It was concluded that these pellets could be handled, stored and transported using equipment similar to that used for coal. Tests showed that AFP pellets have a high combustion rate when burned in a stoker type systems. While NOx emissions under stoker type firing conditions was high, a simple air staging approach reduced emissions to below that for coal. In pulverized-fuel-fired tests it was

  1. Coupled fluid and solid mechanics study for improved permeability estimation of fines' invaded porous materials

    Science.gov (United States)

    Mirabolghasemi, M.; Prodanovic, M.

    2012-12-01

    The problem of fine particle infiltration is seen in fields from subsurface transport, to drug delivery to industrial slurry flows. Sediment filtration and pathogen retention are well-known subsurface engineering problems that have been extensively studied through different macroscopic, microscopic and experimental modeling techniques Due to heterogeneity, standard constitutive relationships and models yield poor predictions for flow (e.g. permeability) and rock properties (e.g. elastic moduli) of the invaded (damaged) porous media. This severely reduces our ability to, for instance, predict retention, pressure build-up, newly formed flow pathways or porous medium mechanical behavior. We chose a coupled computational fluid dynamics (CFD) - discrete element modeling (DEM) approach to simulate the particulate flow through porous media represented by sphere packings. In order to minimize the uncertainty involved in estimating the flow properties of porous media on Darcy scale and address the dynamic nature of filtration process, this microscopic approach is adapted as a robust method that can incorporate particle interaction physics as well as the heterogeneity of the porous medium.. The coupled simulation was done in open-source packages which has both CFD (openFOAM) and DEM components (LIGGGHTS). We ran several sensitivity analyses over different parameters such as particle/grain size ratio, fluid viscosity, flow rate and sphere packing porosity in order to investigate their effects on the depth of invasion and damaged porous medium permeability. The response of the system to the variation of different parameters is reflected through different clogging mechanism; for instance, bridging is the dominant mechanism of pore-throat clogging when larger particles penetrate into the packing, whereas, in case of fine particles which are much smaller than porous medium grains (1/20 in diameter), this mechanism is not very effective due to the frequent formation and

  2. Study on Finite Element Analysis of Fine Solid Lines by Flexographic Printing in Printed Antennas for RFID Transponder

    Directory of Open Access Journals (Sweden)

    M. I. Maksud

    2012-12-01

    Full Text Available Printing is offering the feasibility of producing mass quantities of a wide variety of electronic components and devices quickly and at lower cost. Flexography is mainly used for packaging applications, but is also poses a potential method for the micro manufacture of electronic devices, smart packaging and RFID. The flexographic printing process poses as an attractive candidate for printing electronics for its high speed printing capabilities where such volume and large active areas need to be printed. Therefore an investigation for its potential usage in printing electronics are highly in demand hence a research for suitable conductive ink related to this process is vital. Multiple fine solid lines of high quality are essential to enable printing of ink tracks for electronic applications. A step by step approach by printing multiple solid lines, measurements of printing plates and printed images and finite element analysis (FEA need to be carried out in advance to help comprehending this process that is influenced by many interacting parameters. Plate characteristics are among a number of process parameters that will influence print line quality, which will affect the electrical performance of printed tracks. Printing trials have also been carried out in comparison various ink to check the compatibility and the suitability of the ink developed for printing RFID antennas.

  3. Effects of fining on phenolic compounds and colour of red wine obtained with addition of increased amounts of grape solid phase in pomace

    Directory of Open Access Journals (Sweden)

    Puškaš Vladimir S.

    2012-01-01

    Full Text Available The purpose of this work is to study the effect of grape pomace enrichment in solid phase (stems and seeds on phenolic compounds and colour stability of obtained red wines, before and after use of different fining agents. Results have shown increase in total phenols and flavan-3-ols content after grape solid phase addition. On the other hand, decrease in anthocyanins content has generally been recorded in all wine samples except in wines obtained with addition of 40 g/l of seeds during maceration. Stems addition caused decrease in colour intensity while addition of seeds has increased this colour parameter. The use of four fining agents (albumin, gelatine, bentonite and PVPP has been investigated and compared, especially in terms of their influence on potential stabilization effect of grape solid phase on wine colour. Fined wines tended to have considerably lower anthocyanin and flavan-3-ol levels, especially in the case of gelatine and PVPP treatment (decrease up to 60 and 70%, respectively. In the case of chromatic parameters, used fining agents caused colour intensity decrease but it is important to emphasize that their values, after fining, are still as high as expected from red wine. This can be explained by the stabilization effect of increased flavan-3-ols content.

  4. Fine particulate speciation profile and emission factor of municipal solid waste incinerator established by dilution sampling method.

    Science.gov (United States)

    Yang, Hsi-Hsien; Luo, Shao-Wei; Lee, Kuei-Ting; Wu, Jhin-Yan; Chang, Chun Wei; Chu, Pei Feng

    2016-08-01

    In this study, fine particulate matter (PM2.5) emitted from a municipal solid waste incinerator (MSWI) was collected using dilution sampling method. Chemical compositions of the collected PM2.5 samples, including carbon content, metal elements, and water-soluble ions, were analyzed. Traditional in-stack hot sampling was simultaneously conducted to compare the influences of dilution on PM2.5 emissions and the characteristics of the bonded chemical species. The results, established by a dilution sampling method, show that PM2.5 and total particulate matter (TPM) emission factors were 61.6 ± 4.52 and 66.1 ± 5.27 g ton-waste(-1), respectively. The average ratio of PM2.5/TPM is 0.93, indicating that more than 90% of PM emission from the MSWI was fine particulate. The major chemical species in PM2.5 included organic carbon (OC), Cl(-), NH4(+), elemental carbon (EC) and Si, which account for 69.7% of PM2.5 mass. OC was from the unburned carbon in the exhaust, which adsorbed onto the particulate during the cooling process. High Cl(-) emission is primarily attributable to wastes containing plastic bags made of polyvinyl chloride, salt in kitchen refuse and waste biomass, and so on. Minor species that account for 0.01-1% of PM2.5 mass included SO4(2-), K(+), Na, K, NO3(-), Al, Ca(2+), Zn, Ca, Cu, Fe, Pb, and Mg. The mean ratio of dilution method/in-stack hot method was 0.454. The contents of water-soluble ions (Cl(-), SO4(2-), NO3(-)) were significantly enriched in PM2.5 via gas-to-particle conversion in the dilution process. Results indicate that in-stack hot sampling would underestimate levels of these species in PM2.5. PM2.5 samples from a municipal solid waste incinerator (MSWI) were collected simultaneously by a dilution sampling technique and a traditional in-stack method. PM2.5 emission factors and chemical speciation profiles were established. Dilution sampling provides more reliable data than in-stack hot sampling. The results can be applied to estimate the PM2

  5. Concurrent fine needle aspirations and core needle biopsies: a comparative study of substrates for next-generation sequencing in solid organ malignancies.

    Science.gov (United States)

    Roy-Chowdhuri, Sinchita; Chen, Hui; Singh, Rajesh R; Krishnamurthy, Savitri; Patel, Keyur P; Routbort, Mark J; Manekia, Jawad; Barkoh, Bedia A; Yao, Hui; Sabir, Sharjeel; Broaddus, Russell R; Medeiros, L Jeffrey; Staerkel, Gregg; Stewart, John; Luthra, Rajyalakshmi

    2017-01-13

    Minimally invasive procedures, such as fine needle aspiration and core needle biopsy, are commonly used for the diagnosis in solid organ malignancies. In the era of targeted therapy, it is crucial for molecular testing to be performed on these limited volume specimens. Although several recent studies have demonstrated the utility of small biopsy specimens for molecular testing, there remains debate as to whether core needle biopsy specimens are more reliable than fine needle aspiration for molecular studies. In this study, we reviewed concurrently acquired fine needle aspiration and core needle biopsy samples (n=24), and compared overall cellularity, tumor fraction, and the results of next-generation sequencing. All somatic mutations detected in core needle biopsy samples were also detected in fine needle aspiration samples. The estimated tumor fraction was significantly higher in fine needle aspiration smears than core needle biopsy samples (P=0.003), whereas the overall DNA yield from smears was significantly lower than that obtained from the core needle biopsy specimens (P=0.01). The normalized average amplicon coverage for the genes analyzed was significantly higher in cytology smears than paired core needle biopsy samples, with lower numbers of failed amplicons and higher overall mutation allelic frequencies seen in the former. We further evaluated 100 malignant fine needle aspiration and core needle biopsy samples, acquired concurrently, for overall cellularity and tumor fraction. Overall cellularity and tumor fraction of fine needle aspiration samples was significantly higher than concurrently acquired core needle biopsy samples (Pcore needle biopsy samples. Cytologic specimens, therefore, should be better integrated into routine molecular diagnostics workflow to maximize limited tissues for clinically relevant genomic testing.Modern Pathology advance online publication, 13 January 2017; doi:10.1038/modpathol.2016.228.

  6. A prospective randomized study comparing 25-G and 22-G needles of a new platform for endoscopic ultrasound-guided fine needle aspiration of solid masses.

    Science.gov (United States)

    Carrara, Silvia; Anderloni, Andrea; Jovani, Manol; Di Tommaso, Luca; Rahal, Daoud; Hassan, Cesare; Ridola, Lorenzo; Federico, Davide; Loriga, Alessandra; Repici, Alessandro

    2016-01-01

    A new needle platform for endoscopic ultrasound-guided fine-needle aspiration biopsy has been developed that allows interchangeability of all needle sizes. To prospectively compare the efficacy of the new 25-G needles and 22-G needles for obtaining an adequate aspirate of solid masses. Randomized controlled trial of 144 patients referred for endoscopic ultrasound-guided fine-needle aspiration of solid pancreatic masses, intraparietal tumours, or lymph-nodes, randomized to the 25-G or 22-G needle arms. An adequate specimen was obtained from 74.3% of cases. The sample tended to be more adequate in the 25-G compared to the 22-G group (81% vs. 68%; p=0.09). Crossover was required in 14 (19%) and 12 (17%) cases in the 22-G and in the 25-G groups, respectively (p=0.7). The overall rate of adequacy improved from 74% before crossover to 90% after crossover (pneedle was superior to the 22-G needle for endoscopic ultrasound-guided fine-needle aspiration biopsy. The adequacy and diagnostic accuracy improved after crossover, reaching 90%. Copyright © 2015 Editrice Gastroenterologica Italiana S.r.l. Published by Elsevier Ltd. All rights reserved.

  7. Comparing Endoscopic Ultrasound-Fine-needle Aspiration and Endoscopic Ultrasound-Fine-needle Biopsy for Solid Lesions: A Multicenter, Randomized Trial-The New York Endoscopic Research Outcomes Group (NYERO).

    Science.gov (United States)

    Nagula, Satish; Pourmand, Kamron; Aslanian, Harry; Bucobo, Juan Carlos; Gonda, Tamas; Gonzalez, Susana; Goodman, Adam; Gross, Seth A; Ho, Sammy; DiMaio, Christopher J; Kim, Michelle; Pais, Shireen; Poneros, John; Robbins, David; Schnoll-Sussman, Felice; Sethi, Amrita; Buscaglia, Jonathan M

    2017-06-15

    Endoscopic ultrasound with fine-needle aspiration (FNA) is the standard of care for tissue sampling of solid lesions adjacent to the gastrointestinal tract. Fine-needle biopsy (FNB) may provide higher diagnostic yield with fewer needle passes. The aim of this study was to assess the difference in diagnostic yield between FNA and FNB. This is a multicenter, prospective randomized clinical trial from 6 large tertiary care centers. Patients referred for tissue sampling of solid lesions were randomized to either FNA or FNB of the target lesion. Demographics, size, location, number of needle passes, and final diagnosis were recorded. After enrollment, 135 patients were randomized to FNA (49.3%), and 139 patients were randomized to FNB (50.7%).The following lesions were sampled: mass (n = 210, 76.6%), lymph nodes (n = 46, 16.8%), and submucosal tumors (n = 18, 6.6%). Final diagnosis was malignancy (n = 192, 70.1%), reactive lymphadenopathy (n = 30, 11.0%), and spindle cell tumors (n = 24, 8.8%). FNA had a diagnostic yield of 91.1% compared with 88.5% for FNB (P = .48). There was no difference between FNA and FNB when stratified by the presence of on-site cytopathology or by type of lesion sampled. A median of 1 needle pass was needed to obtain a diagnostic sample for both needles. FNA and FNB obtained a similar diagnostic yield with a comparable number of needle passes. On the basis of these results, there is no significant difference in the performance of FNA compared with FNB in the cytologic diagnosis of solid lesions adjacent to the gastrointestinal tract. ClinicalTrials.gov identifier: NCT01698190. Copyright © 2017 AGA Institute. Published by Elsevier Inc. All rights reserved.

  8. Formation of CoAl2O4 Nanoparticles via Low-Temperature Solid-State Reaction of Fine Gibbsite and Cobalt Precursor

    OpenAIRE

    Natpakan Srisawad; Wasu Chaitree; Okorn Mekasuwandumrong; Piyasan Praserthdam; Joongjai Panpranot

    2012-01-01

    Nanocrystalline cobalt aluminate (CoAl2O4) was synthesized by the solid-state reaction method with cobalt chloride hexahydrate (CoCl2 · 6H2O) as the source of Co and gibbsite (Al(OH)3) as the source of Al, respectively. The effects of particle size of the starting fine gibbsite (0.6 and 13 μm) and calcination temperatures (450, 550, and 650°C) on the properties of CoAl2O4 were investigated by means of X-ray diffraction (XRD), thermogravimetry analysis and differential thermal analysis (TG/DT...

  9. Formation of fine particles in co-combustion of coal and solid recovered fuel in a pulverized coal-fired power station

    DEFF Research Database (Denmark)

    Wu, Hao; Pedersen, Anne Juul; Glarborg, Peter

    2011-01-01

    Fine particles formed from combustion of a bituminous coal and co-combustion of coal with 7 th% (thermal percentage) solid recovered fuel (SRF) in a pulverized coal-fired power plant were sampled and characterized in this study. The particles from dedicated coal combustion and co-combustion both...... appear to be an important formation mechanism. The elemental composition of the particles from coal combustion showed that S and Ca were significantly enriched in ultrafine particles and P was also enriched considerably. However, compared with supermicron particles, the contents of Al, Si and K were...

  10. Preparation of ultra-fine powders from polysaccharide-coated solid lipid nanoparticles and nanostructured lipid carriers by innovative nano spray drying technology.

    Science.gov (United States)

    Wang, Taoran; Hu, Qiaobin; Zhou, Mingyong; Xue, Jingyi; Luo, Yangchao

    2016-09-10

    In this study, five polysaccharides were applied as natural polymeric coating materials to prepare solid lipid nanoparticles (SLN) and nanostructure lipid carriers (NLC), and then the obtained lipid colloidal particles were transformed to solid powders by the innovative nano spray drying technology. The feasibility and suitability of this new technology to generate ultra-fine lipid powder particles were evaluated and the formulation was optimized. The spray dried SLN powder exhibited the aggregated and irregular shape and dimension, but small, uniform, well-separated spherical powder particles of was obtained from NLC. The optimal formulation of NLC was prepared by a 20-30% oleic acid content with carrageenan or pectin as coating material. Therefore, nano spray drying technology has a potential application to produce uniform, spherical, and sub-microscale lipid powder particles when the formulation of lipid delivery system is appropriately designed. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Harmonic Contrast-Enhanced Endoscopic Ultrasonography for the Guidance of Fine-Needle Aspiration in Solid Pancreatic Masses

    DEFF Research Database (Denmark)

    Seicean, A; Badea, R; Moldovan-Pop, A;

    2015-01-01

    Purpose: The global accuracy of fine-needle aspiration guided by endoscopic ultrasound (EUS-FNA) for pancreatic adenocarcinoma is about 85 %. The use of contrast agents during EUS to highlight vessels and the necrotic parts of pancreatic masses may improve biopsy guidance. Our aim was to assess w...

  12. Formation of CoAl2O4 Nanoparticles via Low-Temperature Solid-State Reaction of Fine Gibbsite and Cobalt Precursor

    Directory of Open Access Journals (Sweden)

    Natpakan Srisawad

    2012-01-01

    Full Text Available Nanocrystalline cobalt aluminate (CoAl2O4 was synthesized by the solid-state reaction method with cobalt chloride hexahydrate (CoCl2 · 6H2O as the source of Co and gibbsite (Al(OH3 as the source of Al, respectively. The effects of particle size of the starting fine gibbsite (0.6 and 13 μm and calcination temperatures (450, 550, and 650°C on the properties of CoAl2O4 were investigated by means of X-ray diffraction (XRD, thermogravimetry analysis and differential thermal analysis (TG/DTA, X-ray photoelectron spectroscopy (XPS, UV-visible absorption spectroscopy (UV-Vis, scanning electron microscopy (SEM, and transmission electron microscopy (TEM. Increasing of calcination temperature promoted the insertion amounts of Co2+ in alumina matrix in CoAl2O4 structure, which resulted in the brighter blue particles and increasing of UV spectra band. The lowest temperature for the formation of nanocrystalline CoAl2O4 particles was 550°C for the solid-state reaction of cobalt chloride and 0.6 μm fine gibbsite.

  13. COMPORTEMENT D’UN COMPOSITE FINE MINERALE - CIMENT - BOIS ELABORE A L’AIDE DE DECHETS INDUSTRIELS SOLIDES

    Directory of Open Access Journals (Sweden)

    M.L BENMALEK

    2000-06-01

    Full Text Available Cinq fines minérales de différentes natures minéralogiques et de limites granulaires comparables, provenant de résidus de carrières, ont été traitées pour former le squelette de bétons légers d'isolation. L'allégement et le pouvoir isolant de ces bétons sont obtenus par incorporation de granulats de bois dans la matrice constituée de la fine minérale et de ciment CPA. Dans une première partie, sont présentés les principales caractéristiques de ces fines: minéralogie par diffraction des rayons X, granulométrie laser, conductivité thermique à la sonde TPS, densité sèche par  pycnomètrie à eau et morphologie au MEB. La seconde partie est consacrée à l'étude de l'effet des caractéristiques de ces fines sur le comportement hygrothermique et mécanique de ces bétons élaborés avec une même formulation et un même état de consistance au moulage. Les résultats de ces investigations sont comparés entre eux et  à ceux de matériaux usuels classés par la RILEM.

  14. Comparison of Ultrasound-Guided Core Needle Biopsy and Endoscopic Ultrasound-Guided Fine-Needle Aspiration for Solid Pancreatic Lesions.

    Science.gov (United States)

    Sur, Young Keun; Kim, Young Chul; Kim, Jai Keun; Lee, Jei Hee; Yoo, Byung Moo; Kim, Young Bae

    2015-12-01

    The objective of our study was to compare the diagnostic yield of endoscopic ultrasound (EUS)-guided fine-needle aspiration (FNA) using a 25-gauge needle and ultrasound (US)-guided core needle biopsy (CNB) using an 18-gauge core needle for diagnosis of solid pancreatic lesions. This retrospective study was approved by our Institutional Review Board, and the requirement for informed consent was waived. Patients who underwent either EUS-guided FNA or US-guided CNB for a solid pancreatic lesion from January 2008 to December 2012 were included and reviewed. Fine-needle aspirations and CNBs were performed by experienced endoscopists and radiologists. The diagnostic yield, accuracy, technical failure rate, sensitivity, and specificity for malignancy were calculated and compared. A total of 106 biopsy attempts were undertaken in 89 patients (EUS-guided FNA, n = 70; US-guided CNB, n = 36). Biopsy specimens were successfully obtained in 98 biopsy attempts (EUS-guided FNA, n = 63; US-guided CNB, n = 35). The accuracy, technical failure rate, sensitivity, and specificity of EUS-guided FNA for malignancy (73.02%, 10.00%, 77.78%, and 44.44%, respectively) was not significantly different from those of US-guided CNB (88.57%, 2.78%, 87.10%, and 100%, respectively; P ≥ .089). Diagnostic performance did not differ between the modalities according to the size and the location of the lesion in the pancreas. However, the diagnostic yield of US-guided CNB (86.11%) was higher than that of EUS-guided FNA (65.71%, P = .035). The diagnostic yield of US-guided CNB for solid pancreatic lesions is superior to that of EUS-guided FNA. © 2015 by the American Institute of Ultrasound in Medicine.

  15. Synergistic Utilization of Coal Fines and Municipal Solid Waste in Coal-Fired Boilers. Phase I Final Report

    Energy Technology Data Exchange (ETDEWEB)

    V. Zamansky; P. Maly; M. Klosky

    1998-06-12

    A feasibility study was performed on a novel concept: to synergistically utilize a blend of waste coal fines with so-called E-fuel for cofiring and reburning in utility and industrial boilers. The E-fuel is produced from MSW by the patented EnerTech's slurry carbonization process. The slurry carbonization technology economically converts MSW to a uniform, low-ash, low-sulfur, and essentially chlorine-free fuel with energy content of about 14,800 Btu/lb.

  16. Endoscopic ultrasound-guided fine-needle aspiration cytology diagnosis of solid pseudopapillary tumor of the pancreas:A case report and literature review

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    We describe the clinical, imaging and cytopathological features of solid pseudopapillary tumor of the pancreas (SPTP) diagnosed by endoscopic ultrasoundguided (EUS-guided) fine-needle aspiration (FNA). A 17-year-old woman was admitted to our hospital with complaints of an unexplained episodic abdominal pain for 2 mo and a short history of hypertension in the endocrinology clinic. Clinical laboratory examinations revealed polycystic ovary syndrome, splenomegaly and low serum amylase and carcinoembryonic antigen (CEA)levels. Computed tomography (CT) analysis revealed a mass of the pancreatic tail with solid and cystic consistency. EUS confirmed the mass, both in body and tail of the pancreas, with distinct borders, which caused dilation of the peripheral part of the pancreatic duct (major diameter 3.7 mm). The patient underwent EUS-FNA. EUS-FNA cytology specimens consisted of single cells and aggregates of uniform malignant cells,forming microadenoid structures, branching, papillary clusters with delicate fibrovascular cores and nuclear overlapping. Naked capillaries were also seen. The nuclei of malignant cells were round or oval, eccentric with fine granular chromatin, small nucleoli and nuclear grooves in some of them. The malignant cells were periodic acid Schiff (PAS)-Alcian blue (+) and immunocytochemically they were vimentin (+), CA 19.9 (+), synaptophysin (+), chromogranin (-), neuro-specific enolase (-), a1-antitrypsin and a1-antichymotrypsin focal positive.Cytologic findings were strongly suggestive of SPTP.Biopsy confirmed the above cytologic diagnosis. EUS-guided FNA diagnosis of SPTP is accurate. EUS findings,cytomorphologic features and immunostains of cell block help distinguish SPTP from pancreatic endocrine tumors,acinar cell carcinoma and papillary mucinous carcinoma.

  17. Fine refinement of solid-state molecular structures of Leu- and Met-enkephalins by NMR crystallography.

    Science.gov (United States)

    Pawlak, Tomasz; Potrzebowski, Marek J

    2014-03-27

    This paper presents a methodology that allows the fine refinement of the crystal and molecular structure for compounds for which the data deposited in the crystallographic bases are of poor quality. Such species belong to the group of samples with molecular disorder. In the Cambridge Crystallographic Data Center (CCDC), there are approximately 22,000 deposited structures with an R-factor over 10. The powerful methodology we present employs crystal data for Leu-enkephalin (two crystallographic forms) with R-factor values of 14.0 and 8.9 and for Met-enkephalin (one form) with an R-factor of 10.5. NMR crystallography was employed in testing the X-ray data and the quality of the structure refinement. The GIPAW (gauge invariant projector augmented wave) method was used to optimize the coordinates of the enkephalins and to compute NMR parameters. As we reveal, this complementary approach makes it possible to generate a reasonable set of new coordinates that better correlate to real samples. This methodology is general and can be employed in the study of each compound possessing magnetically active nuclei.

  18. Comparison of two different size needles in endoscopic ultrasound-guided fine-needle aspiration for diagnosing solid pancreatic lesions

    Science.gov (United States)

    Xu, Mei-Mei; Jia, Hong-Yu; Yan, Li-Li; Li, Shan-Shan; Zheng, Yue

    2017-01-01

    Abstract Background: This meta-analysis aimed to provide a pooled analysis of prospective controlled trials comparing the diagnostic accuracy of 22-G and 25-G needles on endoscopic ultrasonography (EUS-FNA) of the solid pancreatic mass. Methods: We established a rigorous study protocol according to Cochrane Collaboration recommendations. We systematically searched the PubMed and Embase databases to identify articles to include in the meta-analysis. Sensitivity, specificity, and corresponding 95% confidence intervals were calculated for 22-G and 25-G needles of individual studies from the contingency tables. Results: Eleven prospective controlled trials included a total of 837 patients (412 with 22-G vs 425 with 25-G). Our outcomes revealed that 25-G needles (92% [95% CI, 89%–95%]) have higher sensitivity than 22-G needles (88% [95% CI, 84%–91%]) on solid pancreatic mass EUS-FNA (P = 0.046). However, there were no significant differences between the 2 groups in overall diagnostic specificity (P = 0.842). The pooled positive and negative likelihood ratio of the 22-G needle were 12.61 (95% CI, 5.65–28.14) and 0.16 (95% CI, 0.12–0.21), respectively. The pooled positive likelihood ratio was 12.61 (95% CI, 5.65–28.14), and the negative likelihood ratio was 0.16 (95% CI, 0.12–0.21) for the 22-G needle. The pooled positive likelihood ratio was 8.44 (95% CI, 3.87–18.42), and the negative likelihood ratio was 0.13 (95% CI, 0.09–0.18) for the 25-G needle. The area under the summary receiver operating characteristic curve was 0.97 for the 22-G needle and 0.96 for the 25-G needle. Conclusion: Compared to the study of 22-G EUS-FNA needles, our study showed that 25-G needles have superior sensitivity in the evaluation of solid pancreatic lesions by EUS–FNA. PMID:28151856

  19. Cell-block procedure in endoscopic ultrasound-guided-fine-needle-aspiration of gastrointestinal solid neoplastic lesions

    Institute of Scientific and Technical Information of China (English)

    Antonio; Ieni; Valeria; Barresi; Paolo; Todaro; Rosario; Alberto; Caruso; Giovanni; Tuccari

    2015-01-01

    In the present review we have analyzed the clinical applications of endoscopic ultrasound-guided-fineneedle-aspiration(EUS-FNA) and the methodological aspects obtained by cell-block procedure(CBP) in the diagnostic approach to the gastrointestinal neoplastic pathology. CBP showed numerous advantages in comparison to the cytologic routine smears; in particular, better preservation of cell architecture, achievement of routine haematoxylin-eosin staining equivalent to histological slides and possibility to perform immunohistochemistry or molecular analyses represented the most evident reasons to choose this method. Moreover, by this approach, the differential diagnosis of solid gastrointestinal neoplasias may be more easily achieved and the background of contaminant nonneoplastic gastrointestinal avoided. Finally, biological samples collected by EUS-FNA CBP-assisted should be investigated in order to identify and quantify further potential molecular markers.

  20. Diagnostic efficacy of liquid-based cytology for solid pancreatic lesion samples obtained with endoscopic ultrasound-guided fine-needle aspiration: Propensity score-matched analysis.

    Science.gov (United States)

    Hashimoto, Shinichi; Taguchi, Hiroki; Higashi, Michiyo; Hatanaka, Kazuhito; Fujita, Toshihiro; Iwaya, Hiromichi; Nakazawa, Junichi; Arima, Shiho; Iwashita, Yuji; Sasaki, Fumisato; Nasu, Yuichiro; Kanmura, Shuji; Ido, Akio

    2017-07-01

    There is a paucity of data on the diagnostic efficacy of liquid-based cytology (LBC) for pancreatic samples obtained by endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA). Using propensity score matching, we retrospectively analyzed the additional diagnostic value of LBC compared to a conventional Papanicolaou smear (CPS) for samples of solid pancreatic lesions obtained by EUS-FNA. This cohort study included 126 matched patients who underwent initial EUS-FNA for solid pancreatic lesions between January 2009 and August 2014. CPS was used for cytology of EUS-FNA samples obtained until May 2012 (63 patients). Subsequently, LBC was used for cytological analysis (63 patients). Diagnostic yields of CPS and LBC for malignancy were compared. Risk factors for cytological misdiagnosis with LBC were investigated. Overall rate of malignancy was 86% after matching. LBC had higher diagnostic sensitivity and accuracy than CPS (96.6% vs 84.0%, P = 0.03; and 96.8% vs 87.3%, P = 0.05). LBC was significantly more sensitive for diagnosing pancreatic head lesions (96.4% vs 78.1%, P = 0.04). The sensitivity for pancreatic ductal adenocarcinoma (PDAC) with LBC was higher (98.1% vs 83.0%, P = 0.009). Multivariate analysis revealed that malignant tumors other than PDAC (P = 0.004) and lesion size ≤20 mm (P = 0.046) were risk factors for LBC misdiagnosis in all participants. For solid pancreatic lesions, LBC of EUS-FNA samples contributes to the diagnosis of malignancy. Malignant tumors other than PDAC and small tumors are difficult to diagnose using EUS-FNA and LBC. © 2017 Japan Gastroenterological Endoscopy Society.

  1. SOLIDS CIRCULATION RATE OF ULTRA-FINE POWDERS IN SPOUTED BED WITH DRAFT TUBE%超细粉在导向管喷动床中的固体循环速率

    Institute of Scientific and Technical Information of China (English)

    周勇; 马兰; 石炎福

    2004-01-01

    Ultra-fine powders are difficult to be fluidized due to the strong particle to particle cohesiveness.However, the authors' experiments showed that the ultra-fine powder CaCO3 could be stably fluidized in a spouted bed with a draft tube. The effects of geometric and operating parameters on solid circulation rate of ultra-fine powder CaCO3 were investigated in a 120 mm diameter transparent semicircular spouted bed with a draft tube. Three draft tubes with different sizes were used in this study. It was found that the solids circulation rate was mainly dependent on the drawing rate of the gas jet from the nozzle, then on the gas transport capacity in the draft tube. With increasing gas feed rate, distance between the nozzle and the draft tube inlet and draft tube diameter, the solids circulation rate could be increased. Based on the jet theory, a quantitative correlation was proposed for predicting the solid circulation rate of ultra-fine powders in a spouted bed with a draft tube by taking into account the gas transport capacity in the draft tube.

  2. Fine coal particles separation by air-solid magnetic fluidization%气固磁场流态化分选细粒煤

    Institute of Scientific and Technical Information of China (English)

    宋树磊; 赵跃民; 骆振福; 唐利刚; 杨旭亮

    2012-01-01

    利用研制的横流式气固磁稳定流化床,以0.074~0.045 mm粒级磁铁矿粉和磁珠作为高密度和低密度分选介质,对6.0~0.5 mm细粒煤进行连续分选试验。结果表明:当处于稳定流化时,磁场气固流化床比普通气固流化床具有更宽的稳定操作气速范围;外加磁场使磁性颗粒沿磁力线形成平行磁链,增大了床层空隙率,形成了分布均匀的通道,气体通过时不会产生气泡,由此形成了稳定的散式气固磁场流化床;高密度分选和低密度分选的可能偏差分别为0.085,0.075 g/cm3。%Continuous separation tests of fine coal particles of 6. 0-0. 5 mm were done by a crossflow air-solid magneti- cally stabilized fluidized bed ( MSFB ), which used 0. 074-0. 045 mm magnetite powder and magnetite beads as medi- um of high and low density separation respectively. The results show that the range of steadily operational air velocity in air-solid magnetically fluidized beds is broader than that in standard air-solid fluidized beds when they are at stable fluidization. External magnetic field compels the magnetic grains to form parallel magnetic chains following the magnet- ic induction lines, which enlarge the bed voidage and form the uniform air channels. Air bubbles cannot be produced when the air flows through the channels, thus stable and particulate air-solid magnetically fluidized beds coming into being. The possible deviation of high and low density separation are 0. 085 and 0. 075 g/cm3 respectively.

  3. Accuracy of diagnosis of solid pseudopapillary tumor of the pancreas on fine needle aspiration: A multi-institution experience of ten cases

    Directory of Open Access Journals (Sweden)

    Sidra Jahangir

    2015-01-01

    Full Text Available Introduction: Solid pseudopapillary tumor of the pancreas (SPTP is a neoplasm of uncertain origin and indolent biologic behavior with distinctive morphological features occurring predominantly in young women. This tumor has an excellent prognosis compared to neuroendocrine and acinar cell carcinoma, which are close differential diagnoses based on morphology, hence making it crucial to diagnose SPTP correctly. Objectives: To discuss the cytomorphological features of 10 cases of SPTP reported in two institutions and to evaluate the diagnostic accuracy of endoscopic ultrasound (EUS guided fine needle aspiration (FNA cytology in establishing the diagnosis of SPTP. Methods: Ten diagnosed cases of SPTP were retrieved from the computerized endoscopy and pathology databases of our two tertiary care institutions. Nine patients had subsequent histological follow-up available. Eight patients underwent EUS-FNA while one patient each had ultrasound and computed tomography-guided FNA. The rapid on-site evaluation was carried out in all 10 cases, and additional material was retained for cell block preparation. Immunohistochemical (IHC stains ranging from synaptophysin, progesterone receptor, chromogranin, β-catenin, CD10, and NSE were applied on cell blocks. Histological sections of all resected specimens were reviewed, and findings were correlated with those obtained by FNA. Results: Adequate material was obtained in all ten cases. IHC stains helped to confirm the cytological impression of SPTP. Histological examination of resection specimens, available in 9/10 cases, confirmed the cytological diagnosis. Conclusions: FNA particularly that obtained with EUS guidance is an effective tool in the accurate diagnosis of SPTP.

  4. Ultrasound-guided fine-needle aspiration for solid thyroid nodules larger than 10 mm: correlation between sonographic characteristics at the needle tip and nondiagnostic results.

    Science.gov (United States)

    Wu, Hongxun; Zhang, Bingjie; Zang, Yaping; Wang, Jun; Zhu, Beilin; Cao, Yuelong; Liu, Qianyun

    2014-06-01

    The objective of this study was to investigate the effect of the ultrasonographic (US) characteristics and ultrasound elastography (UE) patterns on the probability of a nondiagnostic result when performing ultrasound-guided fine-needle aspiration (UG-FNA) cytological sampling of solid thyroid nodules larger than 10 mm, to determine the efficacy of needle tip localization in UG-FNA. We retrospectively reviewed the cytological results of 710 samples from 355 patients. We compared the US characteristics and UE patterns between nodules with nondiagnostic and diagnostic results, using univariate and multivariate analyses. Among the 710 samples, 81 samples (11.4 %) from 41 patients had nondiagnostic results. According to multivariate analysis, the combinations of hypoechogenicity with avascularity [odds ratio (OR) = 2.42; 95 % confidence interval (CI) 1.37-3.72; p hypoechogenicity with the "hard pattern" (OR = 2.12; 95 % CI 1.58-4.59; p hypoechogenicity with avascularity and the hard pattern (OR = 2.61; 95 % CI 1.40-5.21; p hypoechogenicity and avascularity in US and the hard pattern in UE.

  5. Vanadium fine-structure K-shell electron impact ionization cross sections for fast-electron diagnostic in laser–solid experiments

    Energy Technology Data Exchange (ETDEWEB)

    Palmeri, P., E-mail: patrick.palmeri@umons.ac.be [Astrophysique et Spectroscopie, Université de Mons - UMONS, B-7000 Mons (Belgium); Quinet, P., E-mail: pascal.quinet@umons.ac.be [Astrophysique et Spectroscopie, Université de Mons - UMONS, B-7000 Mons (Belgium); IPNAS, Université de Liège, B-4000 Liège (Belgium); Batani, D., E-mail: batani@celia.u-bordeaux1.fr [CELIA, Université de Bordeaux, F-33400 Talence (France)

    2015-09-15

    The K-shell electron impact ionization (EII) cross section, along with the K-shell fluorescence yield, is one of the key atomic parameters for fast-electron diagnostic in laser–solid experiments through the K-shell emission cross section. In addition, in a campaign dedicated to the modeling of the K lines of astrophysical interest (Palmeri et al. (2012)), the K-shell fluorescence yields for the K-vacancy fine-structure atomic levels of all the vanadium isonuclear ions have been calculated. In this study, the K-shell EII cross sections connecting the ground and the metastable levels of the parent vanadium ions to the daughter ions K-vacancy levels considered in Palmeri et al. (2012) have been determined. The relativistic distorted-wave (DW) approximation implemented in the FAC atomic code has been used for the incident electron kinetic energies up to 20 times the K-shell threshold energies. Moreover, the resulting DW cross sections have been extrapolated at higher energies using the asymptotic behavior of the modified relativistic binary encounter Bethe model (MRBEB) of Guerra et al. (2012) with the density-effect correction proposed by Davies et al. (2013)

  6. Diagnostic accuracies of endoscopic ultrasound-guided fine-needle aspiration with distinct negative pressure suction techniques in solid lesions: A retrospective study

    Science.gov (United States)

    Wang, Ronghua; Wang, Jinlin; Li, Yawen; Duan, Yaqi; Wu, Xiaoli; Cheng, Bin

    2017-01-01

    Endoscopic ultrasound (EUS)-guided fine-needle aspiration (EUS-FNA) is highly accurate in obtaining specific diagnoses for various diseases. The present study aimed to evaluate the diagnostic yields, accuracies and sampling adequacies, of slow-pull, 5 ml suction and 10 ml suction techniques in EUS-FNA of solid lesions. The present study was a retrospective comparative study, which was performed in tertiary academic centers, recognized for their expertise in EUS and EUS-guided FNA. The present study involved 149 patients who underwent EUS-FNA of solid masses. A total of 34 (22.8%), 37 (24.8%) and 78 (52.4%) patients underwent EUS-FNA with slow-pull, 5 ml suction and 10 ml suction techniques, respectively. The EUS-FNA cytology and histology results were compared with those from the gold standard of surgical histopathology [hematoxylin-eosin staining; immunohistochemical test of cluster of differentiation (CD) 79a, CD20 and flow cytometry test] or long-term clinical follow-up. The present retrospective comparative study demonstrated that the diagnostic yields and accuracies of EUS-FNA with slow-pull (86.1%) were significantly superior to those achieved with 5 ml suction (83.3%) or 10 ml suction (69.9%; Psuction group were adequate for histological diagnosis. By contrast, 70.6 (24/34) and 85.9% (67/78) of samples from the slow-pull and 10 ml suction groups were adequate for histological diagnosis, respectively. The samples obtained using 10 ml suction contained more blood compared with those obtained via slow-pull and 5 ml suction (P=0.0056; χ2 test). No complications were noted in any of the three groups. The samples that were obtained for histopathological diagnosis using 5 ml suction were superior to those obtained using slow-pull or 10 ml suction. Additional multi-central prospective studies in which EUS-FNA is performed with variable negative pressures are required to improve the defining of the diagnostic roles of those techniques. PMID:28521473

  7. Slow-pull and different conventional suction techniques in endoscopic ultrasound-guided fine-needle aspiration of pancreatic solid lesions using 22-gauge needles.

    Science.gov (United States)

    Chen, Jia-Ying; Ding, Qing-Yu; Lv, Yang; Guo, Wen; Zhi, Fa-Chao; Liu, Si-De; Cheng, Tian-Ming

    2016-10-21

    To evaluate the cytological diagnostic capacity and sample quality of the slow-pull technique and compare them with different suction techniques. From July 2010 to December 2015, 102 patients with pancreatic solid lesions who underwent endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) with 22-gauge needles were retrospectively evaluated. EUS-FNA diagnosis was based on a cytological examination, and final diagnosis was based on a comprehensive standard of cytological diagnosis, surgical pathology and clinical or imaging follow-up. Cytological specimens were characterized for cellularity and blood contamination. The cytological diagnostic capacity and sample quality of the slow-pull technique and suction techniques with 5-mL/10-mL/20-mL syringes were analyzed. Of all of the EUS-FNA procedures, the slow-pull technique and suction techniques with 5-mL/10-mL/20-mL syringes were used in 31, 19, 34 and 18 procedures, respectively. There were significant differences between these four suction techniques in terms of cytological diagnostic accuracy (90.3% vs 63.2% vs 58.8% vs 55.6%, P = 0.019), sensitivity (88.2% vs 41.7% vs 40.0% vs 36.4%, P = 0.009) and blood contamination (score ≥ 2 for 29.0% vs 52.6% vs 70.6% vs 72.2%, P = 0.003). The accuracy and sensitivity of the slow-pull technique were significantly higher than those of the suction techniques using 5-mL (P = 0.03, P = 0.014), 10-mL (P = 0.005; P = 0.006) and 20-mL syringes (P = 0.01, P = 0.01). Blood contamination was significantly lower in the slow-pull technique than in the suction techniques with 10-mL (P = 0.001) and 20-mL syringes (P = 0.007). The slow-pull technique may increase the cytological diagnostic accuracy and sensitivity with slight blood contamination during EUS-FNA when using 22-gauge needles for solid pancreatic masses.

  8. Anne Fine

    Directory of Open Access Journals (Sweden)

    Philip Gaydon

    2015-04-01

    Full Text Available An interview with Anne Fine with an introduction and aside on the role of children’s literature in our lives and development, and our adult perceptions of the suitability of childhood reading material.Since graduating from Warwick in 1968 with a BA in Politics and History, Anne Fine has written over fifty books for children and eight for adults, won the Carnegie Medal twice (for Goggle-Eyes in 1989 and Flour Babies in 1992, been a highly commended runner-up three times (for Bill’s New Frock in 1989, The Tulip Touch in 1996, and Up on Cloud Nine in 2002, been shortlisted for the Hans Christian Andersen Award (the highest recognition available to a writer or illustrator of children’s books, 1998, undertaken the positon of Children’s Laureate (2001-2003, and been awarded an OBE for her services to literature (2003. Warwick presented Fine with an Honorary Doctorate in 2005.Philip Gaydon’s interview with Anne Fine was recorded as part of the ‘Voices of the University’ oral history project, co-ordinated by Warwick’s Institute of Advanced Study.

  9. Fine de novo sequencing of a fungal genome using only SOLiD short read data: verification on Aspergillus oryzae RIB40.

    Directory of Open Access Journals (Sweden)

    Myco Umemura

    Full Text Available The development of next-generation sequencing (NGS technologies has dramatically increased the throughput, speed, and efficiency of genome sequencing. The short read data generated from NGS platforms, such as SOLiD and Illumina, are quite useful for mapping analysis. However, the SOLiD read data with lengths of <60 bp have been considered to be too short for de novo genome sequencing. Here, to investigate whether de novo sequencing of fungal genomes is possible using only SOLiD short read sequence data, we performed de novo assembly of the Aspergillus oryzae RIB40 genome using only SOLiD read data of 50 bp generated from mate-paired libraries with 2.8- or 1.9-kb insert sizes. The assembled scaffolds showed an N50 value of 1.6 Mb, a 22-fold increase than those obtained using only SOLiD short read in other published reports. In addition, almost 99% of the reference genome was accurately aligned by the assembled scaffold fragments in long lengths. The sequences of secondary metabolite biosynthetic genes and clusters, whose products are of considerable interest in fungal studies due to their potential medicinal, agricultural, and cosmetic properties, were also highly reconstructed in the assembled scaffolds. Based on these findings, we concluded that de novo genome sequencing using only SOLiD short reads is feasible and practical for molecular biological study of fungi. We also investigated the effect of filtering low quality data, library insert size, and k-mer size on the assembly performance, and recommend for the assembly use of mild filtered read data where the N50 was not so degraded and the library has an insert size of ∼2.0 kb, and k-mer size 33.

  10. Local structures of mechanically alloyed Fe100—xCux solid soulutions studied by X—ray absorption fine structure

    Institute of Scientific and Technical Information of China (English)

    WenshengYan; YuzhiLi; 等

    2001-01-01

    The local structures of the immiscible Fe100-xCux alloys(x=0,10,20,40,60,80and100)produced by mechanical alloying have been investigated by XAFS.For the Fe100-xCux(x≥40) solid solutions,the local structures around Fe atoms change from bcc structure to fcc one and the Cu atoms maintain the original coordination geometry after milling for 160 hours.On the contrary,the local structures around Cu atoms in both of Fe80Cu20 and Fe90 Cu10 alloys appear a transition from fcc to bcc structure.We found that the Debye-waller factor σof fcc Fe-Cu phase is larger than that of bcc F-Cu phase,and the σ(0.099A°)around Fe atoms is larger than that (0.089A°) of Cu in the Fe100-xCux(x≥40)solid solutions,This suggests that the mechanically alloyed Fe100-xCux supersaturated solid solution is not a homogeneous alloy,and consists of Fe-rich and Cu-rich regions for various compositions.A possible mechanism for bcc-to-fcc and fcc-to-bcc changes in Fe100-xCux solid solutions is discussed in relation to the interdiffusion and transition induced by the ball milling.

  11. Proposal for a European standard dealing with measuring methods for fine particulate emissions of solid-fuel fired furnaces; Vorschlag einer europaeischen Staubmessnorm fuer Feststoff-Feuerstaetten - Ausarbeitung und Untersuchung eines Typenpruef-Messverfahrens fuer Staubemissionen

    Energy Technology Data Exchange (ETDEWEB)

    Gaegauf, Ch. [Oekozentrum, Langenbruck (Switzerland); Griffin, T. [Fachhochschule Nordwestschweiz/ITFE, Muttenz (Switzerland)

    2007-10-15

    The European standards for type testing of solid fuel burning appliances require only the measurement of carbon monoxide emissions. Many European countries urge the standardisation committees to establish standards for the regulation of fine particulate emissions from flue gases since they face exceeding threshold values of particulate matter in the ambient air. The Technical Committee CEN/TC 295 for the standardisation of solid fuel burning appliances assigned the Centre for Appropriate Technology in Langenbruck, Switzerland with the development of a European Technical Specification (CEN TS) for the determination of particulate emission. The new draft of the TS is based on constant volume sampling (CVS) of the entire flue gas flow in a dilution tunnel. The scientific research has been done in the Swiss test laboratory for solid fuel burning appliances and boilers at the University of Applied Sciences, in Basle. The TS is designed in such a way that it can be integrated into the test cycles required by various European standards. The investigation covered work on parameters such as dilution factor, sampling temperature and isokinetics. Tests with a wood log burning appliance and a pellet stove showed that emissions in the dilution tunnel were between 7% and 26% for the pellet stove and from 40% up to 160% higher if they were sampled directly from the stack using heated gravimetric filters. It was demonstrated that the differences between the emissions seen in the dilution tunnel and those from the stack increased along with increasing levels of incomplete combustion. (author)

  12. Fine-sized LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders prepared by combined process of gas-phase reaction and solid-state reaction methods

    Science.gov (United States)

    Ju, Seo Hee; Kang, Yun Chan

    The Ni-rich precursor powders with spherical shape and filled morphologies were prepared by spray pyrolysis from the spray solution with citric acid, ethylene glycol and a drying control chemical additive. The precursor powders with controlled morphologies formed the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders with spherical shape and fine size by solid-state reaction with lithium hydroxide. However, the cathode powders prepared from the spray solution without additives had irregular morphologies and were large in size. The precursor powders with hollow and porous morphologies formed cathode powders with irregular and aggregated morphologies. The composition ratios of the nickel, cobalt and manganese components were maintained in the as-prepared, precursor and cathode powders. The initial discharge capacity of the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders with spherical shape and fine size tested at a temperature of 55 °C under a constant current density of 0.5 C was 215 mAh g -1. The discharge capacity of the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders decreased to 81% of the initial value after 30 cycles.

  13. Fine-tuned characterization at the solid/solution interface of organotin compounds grafted onto cross-linked polystyrene by using high-resolution MAS NMR spectroscopy.

    Science.gov (United States)

    Martins, José C; Mercier, Frédéric A G; Vandervelden, Alexander; Biesemans, Monique; Wieruszeski, Jean-Michel; Humpfer, Eberhard; Willem, Rudolph; Lippens, Guy

    2002-08-02

    The structural characterization of organotin compounds that are grafted onto insoluble cross-linked polymers has necessarily been limited to elemental analysis, infrared spectroscopy, and in a few instances, solid-state NMR spectroscopy. This important bottleneck in the development of such grafted systems has been addressed by using high-resolution magic angle spinning (hr-MAS) NMR spectroscopy. The great potential of this technique is demonstrated through the structural characterization of diphenylbutyl-(3,4) and dichlorobutylstannanes (5,6), grafted onto divinylbenzene cross-linked polystyrene by means of a suitable linker (1, 2). First, conditions suitable for the application of hr-MAS NMR spectroscopy were identified by characterizing the (1)H resonance line widths of the grafted organotin moiety following swelling of the functionalized beads in eight representative solvents. The presence of clearly identifiable tin coupling patterns in both the 1D (13)C and 2D (1)H-(13)C HSQC spectra, and the incorporation of (119)Sn chemical shift and connectivity information from hr-MAS 1D (119)Sn and 2D (1)H-(119)Sn HMQC spectra, provide an unprecedented level of characterization of grafted organotins directly at the solid/liquid interface. In addition, the use of hr-MAS (119)Sn NMR for reaction monitoring, impurity detection, and quantification and assessment of the extent of coordination reveals its promise as a novel tool for the investigation of polymer-grafted organotin compounds. The approach described here should be sufficiently general for extension to a variety of other nuclei of interest in polymer-supported organometallic chemistry.

  14. Ultrasonography-guided Fine-needle Aspiration for Solid Thyroid Nodules Less than 5 mm in the Largest Diameter: Comparison in Diagnostic Adequacy and Accuracy According to Nodule Size

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jang Hee; Kim, Dong Wook; Baek, Seung Hun [Busan Paik Hospital, Inje University College of Medicine, Busan (Korea, Republic of)

    2012-03-15

    This study assessed the adequacy and accuracy of ultrasonography (US)-guided fine-needle aspiration (US-FNA) of solid thyroid nodules, less than 5 mm in maximum diameter. From January to December 2009, US-FNA was performed for small solid thyroid nodules in 201 patients. Each thyroid nodule was classified into group A and B according to the largest diameter (1 mm {<=} group A < 3 mm and 3 mm {<=} group B < 5 mm). The adequacy and accuracy of US-FNA in two groups were compared using the histopathological results as a reference standard. Of the 227 thyroid nodules in 201 patients, the inadequacy of US-FNA in group A and B was 24.3% (18/74) and 13.1% (20/153), respectively, showing a statistically significant difference between the two groups (p = 0.0333, chi-square test). Eighty nodules were removed surgically in 72 patients, from which papillary thyroid carcinoma (n = 52), follicular thyroid carcinoma (n = 1), nodular hyperplasia (n = 26), and pseudonodule related to thyroiditis (n = 1) were confirmed. Based on the histopathological results of the 80 surgical nodules, the sensitivity, specificity, positive predictive value, negative predictive value and accuracy of US-FNA in group A and B were 55.0% and 79.4%, 81.8% and 100%, 84.6% and 100%, 50% and 68.2%, and 64.5% and 85.7%, respectively. The adequacy and accuracy of US-FNA for solid thyroid nodules, {>=} 3 mm in the largest diameter, were higher than those of US-FNA for very small nodules, < 3 mm in the largest diameter

  15. Performance of K-ras mutation analysis plus endoscopic ultrasound-guided fine-needle aspiration for differentiating diagnosis of pancreatic solid mass: a meta-analysis

    Institute of Scientific and Technical Information of China (English)

    Xu Ying; Hu Duanmin; Zhu Qi; Sun Yunwei

    2014-01-01

    Background Difficulties persist in differentiating pancreatic ductal adenocarcinomas (PDAC) from pancreatic inflammatory masses (PIM).Auxiliary diagnostic techniques which enhance the endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) diagnostic yield have been attempted,for example,K-ras mutation analysis.We aimed to evaluate the accuracy of K-ras mutation analysis combined with EUS-FNA for the differential diagnosis of PDAC and PIM by pooling data of existing trials.Methods We systematically searched the Medline,PubMed,Web of Science,Embase,and Cochrane Central Trials databases for relevant published studies.Meta-analysis was performed.Pooling was conducted in fixed-effect model or random-effect model.Results In total eight studies,with 696 cases of PDAC and 138 cases of PIM,met our inclusion criteria.The pooled sensitivity,specificity,positive likely ratio and negative likely ratio of K-ras mutation analysis combined with cytopathology for diagnosis of PDAC versus PIM were 90%,95%,13.45,and 0.13,respectively.Especially,among total 123 patients whose EUS-FNA results were inconclusive or negative,fifty-nine had K-ras mutations and were finally diagnosed with PDAC (48%,59/123).Publication bias was not present.Conclusions Combining K-ras mutation analysis with routine cytology moderately improves the ability of EUS-FNA to differentially diagnose between PDAC and PIM,especially for patients with suspected PDAC yet inconclusive EUS-FNA findings,and may prove to be a valuable supplemental method to EUS-FNA.

  16. Extremely fine structured cathode for solid oxide fuel cells using Sr-doped LaMnO3 and Y2O3-stabilized ZrO2 nano-composite powder synthesized by spray pyrolysis

    Science.gov (United States)

    Shimada, Hiroyuki; Yamaguchi, Toshiaki; Sumi, Hirofumi; Nomura, Katsuhiro; Yamaguchi, Yuki; Fujishiro, Yoshinobu

    2017-02-01

    A solid oxide fuel cell (SOFC) for high power density operation was developed with a microstructure-controlled cathode using a nano-composite powder of Sr-doped LaMnO3 (LSM) and Y2O3-stabilized ZrO2 (YSZ) synthesized by spray pyrolysis. The individual LSM-YSZ nano-composite particles, formed by crystalline and amorphous nano-size LSM and YSZ particles, showed spherical morphology with uniform particle size. The use of this powder for cathode material led to an extremely fine microstructure, in which all the LSM and YSZ grains (approximately 100-200 nm) were highly dispersed and formed their own network structures. This microstructure was due to the two phase electrode structure control using the powder, namely, nano-order level in each particle and micro-order level between particles. An anode-supported SOFC with the LSM-YSZ cathode using humidified H2 as fuel and ambient air as oxidant exhibited high power densities, such as 1.29 W cm-2 under a voltage of 0.75 V and a maximum power density of 2.65 W cm-2 at 800 °C. Also, the SOFC could be stably operated for 250 h with no degradation, even at a high temperature of 800 °C.

  17. Field assisted sintering of fine-grained Li7-3xLa3Zr2AlxO12 solid electrolyte and the influence of the microstructure on the electrochemical performance

    Science.gov (United States)

    Botros, Miriam; Djenadic, Ruzica; Clemens, Oliver; Möller, Matthias; Hahn, Horst

    2016-03-01

    The synthesis and processing of fine-grained Li7-3xLa3Zr2AlxO12 (x = 0.15, 0.17, 0.20) solid electrolyte (LLZO) is performed for the first time using a combination of nebulized spray pyrolysis (NSP) and field assisted sintering technique (FAST). Using FAST, the grain growth is suppressed and highly dense ceramics with 93% of the theoretical density are obtained. A tetragonal lattice distortion is observed after the sintering process. Although this structural modification has been reported to have lower Li-ion mobility compared to the cubic modification, the total conductivity of the sample at room temperature is found to be 0.33 mS cm-1, i.e. comparable to phase-pure cubic LLZO. The activation energy of 0.38 eV is also comparable to the literature values. Galvanostatic cycling of a symmetrical cell Li|LLZO|Li shows a good cycling stability over 100 h. The interfacial resistance in contact with Li-metal is determined using alternating current impedance spectroscopy to be 76 Ω cm2 and 69 Ω cm2 before and after cycling at different current densities, respectively.

  18. Contribution to the study of the production and properties of finely divided solids, prepared in a flame reactor (1960); Contribution a l'etude de procedes d'obtention et des proprietes des solides finement divises elabores dans un reacteur a flamme (1960)

    Energy Technology Data Exchange (ETDEWEB)

    Cuer, J.P. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1960-04-15

    Sufficiently fine particles cannot be obtained by the grinding of crystals. It is therefore logical to adopt a method whereby the solid is formed from a compound in the vapour phase notable amongst such compounds, volatile at moderate temperatures, are certain organic derivatives of metals and the metallic halides. Formation of the solid from its gaseous derivative should be possible by hydrolysis or oxidation without the dispersion of the reaction medium being modified. The simplest method seems to be to obtain the reaction in an oxy-hydrogen blow-pipe. When the gases in the blow-pipe contain a volatile metallic compound, precipitation of finely divided solid in the form of oxide is produced in the flame at high temperature. Aluminium, titanium, iron and zirconium oxides and silica, the particles of which are spherical and very homogeneous in diameter, have been prepared in this way. The specific surfaces calculated from the diameters on electron microscope photographs are in agreement with those measured by adsorption of nitrogen at 195 deg. C. The oxides thus prepared are therefore not intensely porous. The properties and size of the oxide particles are studied as a function of various operational parameters, such as flame temperature and concentration of volatile metal derivative in the reactive gases. When the blow-pipe is supplied with oxide particles of small diameter, a very marked increase in size is observed. The properties of these preparations are also examined. (author) [French] Les procedes de broyage des cristaux ne conduisent pas a des particules suffisamment fines. Aussi, il est logique de s'adresser a un procede de formation du solide a partir d'un compose se trouvant en phase vapeur. De tels composes, volatils a des temperatures moderees, sont notamment certains derives organiques des metaux et les halogenures metalliques. La formation du solide a partir de son derive gazeux doit pouvoir etre effectuee par l'hydrolyse ou l

  19. Prospective evaluation of the optimal number of 25-gauge needle passes for endoscopic ultrasound-guided fine-needle aspiration biopsy of solid pancreatic lesions in the absence of an onsite cytopathologist.

    Science.gov (United States)

    Suzuki, Rei; Irisawa, Atsushi; Bhutani, Manoop S; Hikichi, Takuto; Takagi, Tadayuki; Sato, Ai; Sato, Masaki; Ikeda, Tsunehiko; Watanabe, Ko; Nakamura, Jun; Tasaki, Kazuhiro; Obara, Katsutoshi; Ohira, Hiromasa

    2012-11-01

    A prior study with 22-gauge needles recommended more than seven needle passes for endoscopic ultrasound-guided fine-needle aspiration biopsy (EUS-FNA) of solid pancreatic lesions (SPL) without onsite cytopathology for optimal acquisition of cytopathological diagnosis. The feasibility of this recommendation should be re-evaluated considering the later development and popularity of 25-gauge EUS-FNA needles. We aimed to determine the optimal number of needle passes for cytopathological specimen acquisition with 25-gauge needles for EUS-FNA of SPL. A preliminary prospective study of 22 patients with an onsite cytopathology technician showed a sensitivity of 93.3% and a specificity of 100% with four needle passes that was not statistically different from five needle passes. Based on our preliminary study, we fixed the number of needle passes to four (Group A). As a control group, we carried out sampling in consecutive patients using 25-gauge needles with an onsite cytopathologist (Group B). Sampling rate, diagnostic value and complications were evaluated. We enrolled 20 patients in each group. Sampling rate was higher in Group B (20/20, 100%) than in Group A (19/20, 95%), but there was no statistical difference between them (P-value = 0.31). In Group A, sensitivity, specificity and accuracy were 100% among 19. In Group B, sensitivity was 94.1%, specificity 100%, accuracy 95%. There were also no statistical differences between the groups. No complications were seen. Our study suggests that four needle passes using a 25-gauge needle may be sufficient for EUS-FNA of SPL where onsite cytology is not available. © 2012 The Authors. Digestive Endoscopy © 2012 Japan Gastroenterological Endoscopy Society.

  20. INTERACTIONS BETWEEN CATIONIC POLYELECTROLYTE AND PULP FINES

    Directory of Open Access Journals (Sweden)

    Elina Orblin

    2011-05-01

    Full Text Available Papermaking pulps are a mixture of fibres, fibre fragments, and small cells (parenchyma or ray cells, usually called pulp fines. The interactions between pulp fines and a cationic copolymer of acrylamide and acryloxyethyltrimethyl ammonium chloride were investigated based on solid-liquid isotherms prepared under different turbulence, and subsequent advanced surface characterization using X-ray photoelectron spectroscopy (XPS and time-of-flight secondary ion mass spectrometry (ToF-SIMS. The surface charge and surface area of pulp fine substrates were measured by methylene blue sorption-XPS analysis and nitrogen adsorption combined with mercury porosimetry, respectively. The driving force behind polyelectrolyte adsorption was the amount of the surface anionic charge, whereas surface area appeared to be of less importance. Based on a comparison of solid-liquid and XPS sorption isotherms, different polyelectrolyte conformations were suggested, depending on the types of fines: A flatter conformation and partial cell-wall penetration of polyelectrolytes on kraft fines from freshly prepared pulp, and a more free conformation with extended loops and tails on lignocellulosic fines from recycled pulp. Additionally, ToF-SIMS imaging proved that recycled pulp fines contained residual de-inking chemicals (primarily palmitic acid salts that possibly hinder the electrostatic interactions with polyelectrolytes.

  1. Punção aspirativa por agulha fina no diagnóstico de linfadenopatias e tumores sólidos em crianças e adolescentes Fine needle aspiration biopsy in the diagnosis of lymphadenopathies and solid tumors in children and adolescents

    Directory of Open Access Journals (Sweden)

    Wallace Acioli Freire de Gois

    2008-02-01

    Full Text Available OBJETIVO: Avaliar a importância diagnóstica da punção aspirativa por agulha fina (PAAF em crianças e adolescentes portadores de linfadenopatias e tumores sólidos. MÉTODOS: Análise retrospectiva dos pacientes com idade igual ou inferior a 18 anos, atendidos no Centro de Pediatria Cirúrgica do Hospital Universitário de Brasília, Universidade de Brasília, no período de julho de 2000 a julho de 2005. Foram calculados: sensibilidade, especificidade, precisão (acurácia diagnóstica, valor preditivo positivo e valor preditivo negativo. RESULTADOS: Em 50 pacientes estudados, os resultados da PAAF mostraram sensibilidade de 90,9%; especificidade de 100%, precisão diagnóstica de 95% e valores preditivos positivo e negativo de 100% e 90%, respectivamente. CONCLUSÃO: Em nossa experiência, a PAAF é um método preciso, simples e seguro, útil no diagnóstico de linfadenopatias e tumores sólidos em crianças e adolescentes.BACKGROUND: To evaluate the diagnostic value of the fine needle aspiration biopsy in children and adolescents with solid tumors or lymphadenopathy. METHODS: 18 years old or less patients were observed since July 2000 to July 2005. We observed: sensibility, specificity, diagnostic accuracy and predictive value. RESULTS: In 50 studied patients the fine needle aspiration biopsy we found 90.9% sensibility, 100% specificity, 95% diagnostic accuracy, 100% positive predictive value and 90% negative predictive value. CONCLUSION: The fine needle aspiration biopsy is a easy, safe and accurate diagnostic method for solid tumors and lymphadenopathies.

  2. Fine Arts Database (FAD)

    Data.gov (United States)

    General Services Administration — The Fine Arts Database records information on federally owned art in the control of the GSA; this includes the location, current condition and information on artists.

  3. Fine Needle Aspiration

    Science.gov (United States)

    ... FNA), also called fine needle biopsy, is a type of biopsy that can be used to diagnose many types ... in which case another FNA or a different type of biopsy procedure may needed. Because the needle is so ...

  4. Analyses of fine paste ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Sabloff, J A [ed.

    1980-01-01

    Four chapters are included: history of Brookhaven fine paste ceramics project, chemical and mathematical procedures employed in Mayan fine paste ceramics project, and compositional and archaeological perspectives on the Mayan fine paste ceramics. (DLC)

  5. Transport of reservoir fines

    DEFF Research Database (Denmark)

    Yuan, Hao; Shapiro, Alexander; Stenby, Erling Halfdan

    Modeling transport of reservoir fines is of great importance for evaluating the damage of production wells and infectivity decline. The conventional methodology accounts for neither the formation heterogeneity around the wells nor the reservoir fines’ heterogeneity. We have developed an integral...... dispersion equation in modeling the transport and the deposition of reservoir fines. It successfully predicts the unsymmetrical concentration profiles and the hyperexponential deposition in experiments....

  6. A Prospective Randomized Controlled Study Comparing EUS Sonopsy CY(R) and 22-gauge Biopsy Needles for Endoscopic Ultrasound-guided Fine-Needle Aspiration of Solid Pancreatic Mass Lesions.

    Science.gov (United States)

    Mizukawa, Sho; Kato, Hironari; Muro, Shinichiro; Akimoto, Yutaka; Uchida, Daisuke; Tomoda, Takeshi; Matsumoto, Kazuyuki; Yamamoto, Naoki; Horiguchi, Shigeru; Tsutsumi, Koichiro; Okada, Hiroyuki; Inoue, Hirofumi; Tanaka, Noriyuki

    2016-10-01

    Endoscopic ultrasound-guided fine needle aspiration (EUS-FNA) is a standard procedure for precise histological diagnosis of pancreas tumors, but it is sometimes difficult to obtain adequate specimens. EUS Sonopsy CY® is a newly designed needle with original features. This randomized study will compare the tissue collection rate of EUS Sonopsy CY® to that of a conventional needle in EUS-FNA. The major eligibility criteria are as follows: Patients with a pancreatic mass referred for EUSFNA; age 20 years, and performance status<4. The primary outcome is the tissue collection rate. This study will elucidate the efficacy of EUS Sonopsy CY®.

  7. Which fine-tuning arguments are fine?

    CERN Document Server

    Grinbaum, Alexei

    2009-01-01

    The argument from naturalness is widely employed in contemporary quantum field theory. Essentially a formalized aesthetic criterion, it received a meaning in the debate on the Higgs mechanism, which goes beyond aesthetics. We follow the history of technical definitions of fine tuning at the scale of electroweak symmetry breaking. It is argued that they give rise to a special interpretation of probability, which we call Gedankenfrequency. By extension of its original meaning, the argument from naturalness is used to compare different models beyond the Standard Model. We show that in this case naturalness cannot be defined objectively. Rather, it functions as socio-historical heuristics in particle physics and it contributes to the advent of a probabilistic version of Popper's falsificationism.

  8. AQUEOUS BIPHASE EXTRACTION FOR PROCESSING OF FINE COAL

    Energy Technology Data Exchange (ETDEWEB)

    K. Osseo-Asare; X. Zeng

    2002-01-01

    The objective of this research project is to develop an aqueous biphase extraction process for the treatment of fine coals. Aqueous biphase extraction is an advanced separation technology that relies on the ability of an aqueous system consisting of a water-soluble polymer and another component, e.g., another polymer, an inorganic salt, or a nonionic surfactant, to separate into two immiscible aqueous phases. The principle behind the partition of solid particles in aqueous biphase systems is the physicochemical interaction between the solid surface and the surrounding liquid solution. In order to remove sulfur and mineral matter from fine coal with aqueous biphasic extraction, it is necessary to know the partitioning behavior of coal, as well as the inorganic mineral components. Therefore, in this research emphasis was placed on the partitioning behavior of fine coal particles as well as model fine inorganic particles in aqueous biphase systems.

  9. Fine 5 lavastab Venemaal

    Index Scriptorium Estoniae

    2013-01-01

    Tantsuteatru Fine 5 koreograafid Tiina Ollesk ja Rene Nõmmik toovad Jekaterinburgis välja lavastuse "... and Red", esitajaks Venemaa nimekas nüüdistantsutrupp Provintsialnõje Tantsõ. Lavastuses kõlab Taavo Remmeli kontrabassiimprovisatsioon "12.12.2006"

  10. A fine art

    Energy Technology Data Exchange (ETDEWEB)

    Schnabel, G.; Raaff, T. [Andritz AG (Austria)

    2006-07-15

    The paper describes a new dewatering system for coal fines which challenges established processes by using screenbowl centrifuge and hyperbaric filter combinations. Company acquisitions over the past three to four years enabled Andritz AG to develop a new system combining two technologies. The article describes the benefits of the combination process and explains the basic operation of these machines. 4 figs.

  11. The Fine Dutch Tradition

    NARCIS (Netherlands)

    Hooimeijer, F.L.

    2012-01-01

    Publication of the exhibition and symposium on water adaptive urban planning and architecture in Bangkok. The Urban Fine Dutch Tradition is a dynamic tradition of making urban designs using the parameters of the natural system – incorperating in an efficient way the hydrological cycle, the soil and

  12. Imeilus Fine 5

    Index Scriptorium Estoniae

    2017-01-01

    Vaba Lava teatrikeskuse laval esineb Fine 5 oma lavastusega "Imeilus". Tiina Ollesk ja Renee Nõmmik, tantsulavastuse autorid on koreograafid, õppejõud, lavastajad ja kogemustega tantsijad. 29. jaanuaril korraldavad Tiina Ollesk ja Renee Nõmmik Tallinna Ülikoolis kaasaegse liikumismõtlemise töötoa, mis on pühendatud lavastusele "Imeilus"

  13. Fine 5 lavastab Venemaal

    Index Scriptorium Estoniae

    2013-01-01

    Tantsuteatru Fine 5 koreograafid Tiina Ollesk ja Rene Nõmmik toovad Jekaterinburgis välja lavastuse "... and Red", esitajaks Venemaa nimekas nüüdistantsutrupp Provintsialnõje Tantsõ. Lavastuses kõlab Taavo Remmeli kontrabassiimprovisatsioon "12.12.2006"

  14. Computer Models Simulate Fine Particle Dispersion

    Science.gov (United States)

    2010-01-01

    Through a NASA Seed Fund partnership with DEM Solutions Inc., of Lebanon, New Hampshire, scientists at Kennedy Space Center refined existing software to study the electrostatic phenomena of granular and bulk materials as they apply to planetary surfaces. The software, EDEM, allows users to import particles and obtain accurate representations of their shapes for modeling purposes, such as simulating bulk solids behavior, and was enhanced to be able to more accurately model fine, abrasive, cohesive particles. These new EDEM capabilities can be applied in many industries unrelated to space exploration and have been adopted by several prominent U.S. companies, including John Deere, Pfizer, and Procter & Gamble.

  15. Very fine Twilights

    Science.gov (United States)

    Boico, Vladimir

    1992-04-01

    The author is describing a very fine twilight on 3 January 1992 at 17 h25 m LT (The Sunset was at 16h48m LT) of red - terracotta color. The author is relating this twilight with the volcanic erruption of Pinatubo on the Philipines islands from June 1991. The author is describing the following phenomena related with Volcanic erruption: twilights, the greenish of the Moon's surface, a change in the color of Day Sky to white, Haloes around the Sun. The author is pointing out, that the phenomena mentioned could prolonge in time 2 or 3 years.

  16. Characterization of DPOAE fine structure

    DEFF Research Database (Denmark)

    Reuter, Karen; Hammershøi, Dorte

    2005-01-01

    , and has recently been demonstrated to exist in low level equal-loudness contours. The character of the DPOAE fine structure depends on several parameters, i.e., level, frequencies, and frequency of the two primaries, but also level and character of the noise floor. The prevalence and character of the fine......The distortion product otoacoustic emission (DPOAE) fine structure is revealed, when measuring DPOAE with a very fine frequency resolution. It is characterized by consistent maxima and minima with notches of up to 20 dB depth. The fine structure is known also from absolute hearing thresholds...... structures are highly individual, and till now no standardized method has been suggested for a consistent categorization. In the present paper a method developed for the categorization of fine structures is presented. The method has been used in two previous studies on the prevalence of fine structures, 1...

  17. Granulation of fine powder

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ching-Fong

    2016-08-09

    A mixture of fine powder including thorium oxide was converted to granulated powder by forming a first-green-body and heat treating the first-green-body at a high temperature to strengthen the first-green-body followed by granulation by crushing or milling the heat-treated first-green-body. The granulated powder was achieved by screening through a combination of sieves to achieve the desired granule size distribution. The granulated powder relies on the thermal bonding to maintain its shape and structure. The granulated powder contains no organic binder and can be stored in a radioactive or other extreme environment. The granulated powder was pressed and sintered to form a dense compact with a higher density and more uniform pore size distribution.

  18. A Fine Example

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    After 10 years of bidding, Tulou, the unique residential architecture in southeast China’s coastal province of Fujian, has finally made it onto the World Heritage List. This success makes it easierand smoother to protect the centuries-old houses and maintain theancient civilization of the Hakka people, of which they are an inte-gral part.There are around 23,000 Tulous in Fujian. The unique Chineserammed earth buildings come in various shapes and are both aliving and working environment. When the gate is shut, a Tulou becomes a solid fort to defend against enemy invasion. The 46Tulous that have been listed as world heritage sites are just afraction of the total number that dot Fujian’s mountains.

  19. Properties of Industrial Slag as Fine Aggregate in Concrete

    Directory of Open Access Journals (Sweden)

    A. Ananthi

    2015-04-01

    Full Text Available The main objective of this paper is to use the industrial waste such as bottom ash and Weld Slag (WS as the partial replacement for fine aggregates in concrete. This paper presents the chemical analysis and strength properties of industrial solid waste such as bottom ash, weld slag 1 (WS 1 and weld slag 2 (WS 2. Their chemical compositions were identified by X-ray powder diffraction (XRD analysis. The qualitative and quantitative elemental analysis of the bottom ash and weld slag was recognized by energy dispersive X-ray analysis and their morphology were studied by Scanning Electron Microscope (SEM. The compressive strength of concrete with 10% replacement of fine aggregate to the industrial waste shows higher strength than the normal concrete and hence this industrial waste can be used as fine aggregate in concrete.

  20. Pressure flotation of nitrocellulose fines: Hydrodynamics and interfacial chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Grasso, D.; Hu, H.L. [Univ. of Connecticut, Storrs, CT (United States); LaFrance, P. [CH2M Hill, Denver, CO (United States); Kim, B.J. [Army Construction Engineering Lab., Champaign, IL (United States)

    1996-11-01

    The production of nitrocellulose (NC) creates large quantities of waste NC fines in wash water streams. Current processing techniques attempt to remove these fines by cross-flow microfiltration, pressure flotation, settling, centrifugation, and lime precipitation. Pressure flotation, or dissolved air flotation (DAF), is a solid/liquid separation process first developed in the ore processing industry. DAF has since found many applications in the environmental engineering field including: drinking water clarification, sludge thickening, and the clarification of wastewater from a variety of industrial and municipal processes. The work presented herein is part of a larger effort to explore techniques to recover and reuse nitrocellulose (NC) fines resulting from propellant manufacturing processes. Previous papers investigated NC particle stability and interfacial thermodynamics and developed a flotation trajectory model. This paper builds on that work and presents a sensitivity analysis of the flotation trajectory model. The sensitivity analysis explores both operational and parameter estimation uncertainty.

  1. Nitramine Drying & Fine Grinding Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Nitramine Drying and Fine Grinding Facility provides TACOM-ARDEC with a state-of-the-art facility capable of drying and grinding high explosives (e.g., RDX and...

  2. Fine 5 kolib Kumu lavale

    Index Scriptorium Estoniae

    2006-01-01

    Kumu kunstimuuseumi auditooriumis toimub 21. veebruaril Fine 5 kaasaegse tantsu etendus "Panus". Esinevad Tiina Ollesk, Irina Pähn, žonglöör Dimitri Kruus, disainer Rain Saukas ja muusik Mattias Siitan

  3. Briquetting anthracite fines for recycle

    Energy Technology Data Exchange (ETDEWEB)

    Guzman, S.; Price, J.J.

    1993-01-01

    A laboratory study of the briquetting of anthracite fines (recovered from a dryer) with pitch is reported, and a proposed plant flowsheet is discussed. The briquettes would be used with the coarser anthracite in electric furnace smelting of ilmenite.

  4. Fine 5 kolib Kumu lavale

    Index Scriptorium Estoniae

    2006-01-01

    Kumu kunstimuuseumi auditooriumis toimub 21. veebruaril Fine 5 kaasaegse tantsu etendus "Panus". Esinevad Tiina Ollesk, Irina Pähn, žonglöör Dimitri Kruus, disainer Rain Saukas ja muusik Mattias Siitan

  5. Solid propellants.

    Science.gov (United States)

    Marsh, H. E., Jr.; Hutchison, J. J.

    1972-01-01

    The basic principles underlying propulsion by rocket motor are examined together with the configuration of a solid propellant motor. Solid propellants and their preparation are discussed, giving attention to homogeneous propellants, composite propellants, energetic considerations in choosing a solid propellant, the processing of composite propellants, and some examples of new developments. The performance of solid propellants is investigated, taking into account characteristics velocity, the specific impulse, and performance calculations. Aspects of propellant development considered include nonperformance requirements for solid propellants, the approach to development, propellant mechanical properties, and future trends.

  6. The Fine-Tuning Argument

    CERN Document Server

    Landsman, Klaas

    2015-01-01

    Our laws of nature and our cosmos appear to be delicately fine-tuned for life to emerge, in way that seems hard to attribute to chance. In view of this, some have taken the opportunity to revive the scholastic Argument from Design, whereas others have felt the need to explain this apparent fine-tuning of the clockwork of the Universe by proposing the existence of a `Multiverse'. We analyze this issue from a sober perspective. Having reviewed the literature and having added several observations of our own, we conclude that cosmic fine-tuning supports neither Design nor a Multiverse, since both of these fail at an explanatory level as well as in a more quantitative context of Bayesian confirmation theory (although there might be other reasons to believe in these ideas, to be found in religion and in inflation and/or string theory, respectively). In fact, fine-tuning and Design even seem to be at odds with each other, whereas the inference from fine-tuning to a Multiverse only works if the latter is underwritten...

  7. 34 CFR 668.84 - Fine proceedings.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 3 2010-07-01 2010-07-01 false Fine proceedings. 668.84 Section 668.84 Education... Proceedings § 668.84 Fine proceedings. (a) Scope and consequences. (1) The Secretary may impose a fine of up... any institution that contracts with the servicer. (2) If the Secretary begins a fine...

  8. The care of fine books

    CERN Document Server

    Greenfield, Jane; Basbanes, Nicholas A

    2014-01-01

    The Care of Fine Books is a thorough, readable guide to caring for books of value. From a discussion of the various techniques and materials used in bookbinding to advice on handling and storage, Jane Greenfield has created a succinct yet complete resource for anyone who wants to preserve and protect their fine books. Whether you are a collector, a librarian, or a conservation professional, you will benefit from this expert advice. Learn about appropriate levels of light, temperature, relative humidity, and pollution; how to secure a collection against fire, insect infestation, flood, and theft; and methods for cleaning and repairing books that have already been damaged. Always practical and amply illustrated, this is a must-have reference for anyone who loves fine books.

  9. Solid lubricants

    Science.gov (United States)

    Sliney, Harold E.

    1993-01-01

    The state of knowledge of solid lubricants is reviewed. The results of research on solid lubricants from the 1940's to the present are presented from a historical perspective. Emphasis is placed largely, but not exclusively, on work performed at NASA Lewis Research Center with a natural focus on aerospace applications. However, because of the generic nature of the research, the information presented in this review is applicable to most areas where solid lubricant technology is useful.

  10. Solid Matter

    CERN Document Server

    Angelo, Joseph A

    2011-01-01

    Supported by a generous quantity of full-color illustrations and interesting sidebars, Solid Matter introduces the basic characteristics and properties of solid matter. It briefly describes the cosmic connection of the elements, leading readers through several key events in human pre-history that resulted in more advanced uses of matter in the solid state. Chapters include:. -Solid Matter: An Initial Perspective. -Physical Behavior of Matter. -The Gravity of Matter. -Fundamentals of Materials Science. -Rocks and Minerals. -Metals. -Building Materials. -Carbon Earth's Most Versatile Element. -S

  11. Recovery bituminous coal fines: a discussion on the production of coal-water slurry fuels and its relationship to fine coal cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Morrison, J.L.; Scaroni, A.W.; Battista, J.J. [Pennsylvania State University, University Park, PA (United States)

    1998-12-31

    The recovery of bituminous coal fines from slurry impoundments and fine coal cleaning circuits has received considerable attention over the last decade from both coal suppliers and coal-fired utilities. Several coal-fired utilities are presently determining whether a low-solids, low viscosity coal-water slurry fuel (CWSF) produced from fine coal can be co-fired with their normal coal feedstock in order to lower their fuel cost and reduce their NO{sub x} emissions. One of the most visible CWSF demonstration programs in the United States is being conducted by GPU Generating, Inc. (GPU Genco). GPU Genco has conducted intermittent demonstration co-fire testing at their 218 MWe-Seward Station since 1993. These tests successfully demonstrate that a low-solids CWSF can be co-fired with pulverized coal in wall-and tangentially-fired boilers. The majority of the CWSF tested at Seward has been prepared from impounded coal fines cleaned via froth flotation and, on a more limited basis, a CWSF prepared from coal fines concentrated from a screen-bowl centrifuge effluent. The production of alow-solids CWSF from wet, fine coal provides an alternative to dewatering. This paper summarizes several fine coal recovery and utilization programs conducted by Pennsylvania State University (Penn State) and GPU Genco during the last five years. These programs range from performing bench-to-pilot-scale cleanability and pilot-scale combustion testing to full-scale utility demonstration tests. All of these successful programs have a common thread of integrating and addressing the issues of fine coal characterization, cleaning handling, and the combustion performance of the CWSF. 8 refs., 1 fig., 1 tab.

  12. Fine bubble generator and method

    Energy Technology Data Exchange (ETDEWEB)

    Bhagat, P.M.; Koros, R.M.

    1990-10-09

    This patent describes a method of forming fine gaseous bubbles in a liquid ambient. It comprises: forcing a gas through orifices located in the liquid ambient while simultaneously forcing a liquid through liquid orifices at a velocity sufficient to form jet streams of liquid, the liquid orifices being equal in number to the gas orifices and so oriented that each jet stream of liquid intersects the gas forced through each gas orifice and creates sufficient turbulence where the gas and jet stream of liquid intersect, whereby fine gaseous bubbles are formed.

  13. Pressure characteristics of a hydrocyclone for fine particle separation

    Institute of Scientific and Technical Information of China (English)

    ZHAO Li-xin; JIANG Ming-hu; SUN De-zhi; BELAIDI A; THEW M

    2006-01-01

    Solid-liquid hydrocyclones are mainly used to separate large particles, such as the particles of drilling fluid in petroleum industry, and large mineral particles. Till now the hydrocyclonic separation for fine particles is still a big problem. Basic separation principle of hydrocyclones and experimental research facility are simply introduced. The difficulty of separating fine particle is analyzed. Based on a solid-liquid hydrocyclone used for separating fine particles, relationships of dimensionless pressure characteristic parameters, i.e. Euler number and pressure drop ratio, with several main dimensionless parameters, such as split ratio, swirl number and gas-liquid ratio, were experimentally studied in detail. The research was carried out by using the hydrocyclonic separation experimental rig at the University of Bradford. It is shown that the less the size of particle, the less the value of radius of the balance orbit occupied by the particle, and then the more difficult for the particle to be separated. Experiments indicate that Euler number of the tested hydrocyclone increases with the rise of Reynolds number, split ratio, swirl number and gas-liquid ratio respectively, and the pressure drop ratio falls with the increase of Reynolds number, split ratio and swirl number respectively. It is concluded that the most effective way to decrease the unit energy dissipation of hydrocyclone is to reduce swirl number or gas-liquid ratio of the mixed media.

  14. Solid consistency

    Science.gov (United States)

    Bordin, Lorenzo; Creminelli, Paolo; Mirbabayi, Mehrdad; Noreña, Jorge

    2017-03-01

    We argue that isotropic scalar fluctuations in solid inflation are adiabatic in the super-horizon limit. During the solid phase this adiabatic mode has peculiar features: constant energy-density slices and comoving slices do not coincide, and their curvatures, parameterized respectively by ζ and Script R, both evolve in time. The existence of this adiabatic mode implies that Maldacena's squeezed limit consistency relation holds after angular average over the long mode. The correlation functions of a long-wavelength spherical scalar mode with several short scalar or tensor modes is fixed by the scaling behavior of the correlators of short modes, independently of the solid inflation action or dynamics of reheating.

  15. Effects of Solid-Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy

    Science.gov (United States)

    Guo, H. M.; Wang, L. J.; Wang, Q.; Yang, X. J.

    2014-08-01

    The desired starting material for semi-solid processing is the semi-solid slurry in which the solid phase is present as fine and globular particles. A modified solid-liquid mixing (SLM) is reported wherein semi-solid slurry can be produced by mixing a solid alloy block into a liquid alloy, and mechanical vibration is utilized to enhance the mixing. Effects such as liquid alloy temperature, mass ratio, and mixing intensity on the microstructure and the cooling curves during SLM were evaluated. 2D and 3D microstructure analysis of treated A356 aluminum alloy shows that microstructure can be refined significantly with a considerable morphology change in primary Al phase. It is critical that the temperature of mixture after mixing is lower than its liquidus temperature to obtain a valid SLM process. Specially, mixing intensity is identified as a primary factor for a favorable microstructure of semi-solid slurry.

  16. Compressive behavior of fine sand.

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

    2010-04-01

    The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

  17. Observations of substorm fine structure

    Directory of Open Access Journals (Sweden)

    L. L. Lazutin

    Full Text Available Particle and magnetic field measurements on the CRRES satellite were used, together with geosynchronous satellites and ground-based observations, to investigate the fine structure of a magnetospheric substorm on February 9, 1991. Using the variations in the electron fluxes, the substorm activity was divided into several intensifications lasting about 3–15 minutes each. The two main features of the data were: (1 the intensifications showed internal fine structure in the time scale of about 2 minutes or less. We call these shorter periods activations. Energetic electrons and protons at the closest geosynchronous spacecraft (1990 095 were found to have comparable activation structure. (2 The energetic (>69 keV proton injections were delayed with respect to electron injections, and actually coincided in time with the end of the intensifications and partial returns to locally more stretched field line configuration. We propose that the energetic protons could be able to control the dynamics of the system locally be quenching the ongoing intensification and possibly preparing the final large-scale poleward movement of the activity. It was also shown that these protons originated from the same intensification as the preceeding electrons. Therefore, the substorm instability responsible for the intensifications could introduce a negative feedback loop into the system, creating the observed fine structure with the intensification time scales.

    Key words. Magnetospheric Physics (Storms and substorms.

  18. Supercritical fluid molecular spray thin films and fine powders

    Science.gov (United States)

    Smith, Richard D.

    1988-01-01

    Solid films are deposited, or fine powders formed, by dissolving a solid material into a supercritical fluid solution at an elevated pressure and then rapidly expanding the solution through a short orifice into a region of relatively low pressure. This produces a molecular spray which is directed against a substrate to deposit a solid thin film thereon, or discharged into a collection chamber to collect a fine powder. The solvent is vaporized and pumped away. Solution pressure is varied to determine, together with flow rate, the rate of deposition and to control in part whether a film or powder is produced and the granularity of each. Solution temperature is varied in relation to formation of a two-phase system during expansion to control porosity of the film or powder. A wide variety of film textures and powder shapes are produced of both organic and inorganic compounds. Films are produced with regular textural feature dimensions of 1.0-2.0 .mu.m down to a range of 0.01 to 0.1 .mu.m. Powders are formed in very narrow size distributions, with average sizes in the range of 0.02 to 5 .mu.m.

  19. CDC WONDER: Daily Fine Particulate Matter

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Daily Fine Particulate Matter data available on CDC WONDER are geographically aggregated daily measures of fine particulate matter in the outdoor air, spanning...

  20. CDC WONDER: Daily Fine Particulate Matter

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Daily Fine Particulate Matter data available on CDC WONDER are geographically aggregated daily measures of fine particulate matter in the outdoor air, spanning...

  1. Fine Spectra of Symmetric Toeplitz Operators

    Directory of Open Access Journals (Sweden)

    Muhammed Altun

    2012-01-01

    Full Text Available The fine spectra of 2-banded and 3-banded infinite Toeplitz matrices were examined by several authors. The fine spectra of n-banded triangular Toeplitz matrices and tridiagonal symmetric matrices were computed in the following papers: Altun, “On the fine spectra of triangular toeplitz operators” (2011 and Altun, “Fine spectra of tridiagonal symmetric matrices” (2011. Here, we generalize those results to the (2+1-banded symmetric Toeplitz matrix operators for arbitrary positive integer .

  2. Fine coal measurement needs for improved control

    Energy Technology Data Exchange (ETDEWEB)

    Firth, B.; O' Brien, M. [CSIRO, Brisbane, Qld. (Australia). Division of Energy Technology

    2010-07-01

    The monitoring and management of fine coal circuits in coal preparation plants is limited in current practice. As part of the Australian Coal Association Research Program (ACARP) Intelligent Plant Project (C11069), the relationships between the main operational and control factors for the unit operations and the circuit and the performance indicators have been identified. The unit operations examined included desliming (hydrocyclones and sieve bends), small coal cleaning (spirals and hydraulic separators), flotation, and dewatering (vacuum filters, centrifuges, and thickeners). These relationships were then used to assist in the identification of the important parameters to be measured and the preferred level of accuracy required to be useful. An important issue was the interconnection between the various unit operations and the potential impact of an upstream problem on the subsequent performance of downstream units. Analysis with the relationships showed that the flow rate of respective feed slurries and the solids content were found to be significant variables. This article will discuss this analysis and provide some case studies.

  3. Considering Fine Art and Picture Books

    Science.gov (United States)

    Serafini, Frank

    2015-01-01

    There has been a close association between picturebook illustrations and works of fine art since the picturebook was first conceived, and many ways these associations among works of fine art and picturebook illustrations and design play out. To make sense of all the various ways picturebook illustrations are associated with works of fine art,…

  4. 36 CFR 910.35 - Fine arts.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Fine arts. 910.35 Section 910... DEVELOPMENT AREA Standards Uniformly Applicable to the Development Area § 910.35 Fine arts. Fine arts... of art which are appropriate for the development. For information and guidance, a...

  5. Southern Fine Particulate Monitoring Project

    Energy Technology Data Exchange (ETDEWEB)

    Ashley Williamson

    2003-05-31

    This final project report presents experimental details, results and analysis of continuous onsite ambient fine particulate data at the North Birmingham sampling site during the October, 2001-September, 2002 study period.The host site for these measurement activities is the North Birmingham PM monitoring station by the Jefferson County Health Department in Birmingham, AL.The continuous data include PM{sub 2.5} mass concentrations measured by TEOM, particle sulfate using the R&P 8400S monitor, particle size distributions measured by SMPS and APS monitors, and PM{sub 2.5} light scattering extinction coefficient as measured by nephelometer. During the course of the project, measurement intercomparison data were developed for these instruments and several complementary measurements at the site. The report details the instrument set and operating procedures and describes the resulting data. Report subsections present an overview summary of the data, followed by detailed description of the systematic time behavior of PM{sub 2.5} and other specific particulate size fractions. Specific subsections are included for particle size distribution, light scattering, and particle sulfate data. The final subsection addresses application of the measurements to the practical questions of fine PM generation and transport, source attribution, and PM{sub 2.5} management strategies.

  6. Effect of Fine Steel Slag Powder on the Early Hydration Process of Portland Cement

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Hydration heat evolution, non-evaporative water, setting time and SEM tests were performed to investigate the effect of fine steel slag powder on the hydration process of Portland cement and its mechanism.The results show that the effect of fine steel slag powder on the hydration process of Portland cement is closely related to its chemical composition, mineral phases, fineness, etc.Fine steel slag powder retards the hydration of portland cement at early age.The major reason for this phenomenon is the relative high content of MgO , MnO2, P2 O5in steel slag, and MgO solid solved in C3 S contained in steel slag.

  7. FLUIDIZATION OF FINE POWDERS IN FLUIDIZED BEDS WITH AN UPWARD OR A DOWNWARD AIR JET

    Institute of Scientific and Technical Information of China (English)

    Ruoyu Hong; Jianmin Ding; Hongzhong Li

    2005-01-01

    The hydrodynamic behavior of fine powders in jet-fluidized beds was studied numerically and experimentally. The starting point of numerical simulation was the generalized Navier-Stokes (N-S) equations for the gas and solids phases. The κ-εturbulence model was used for high-speed gas jets in fluidized beds. Computation shows that a suitable turbulence model is necessary to obtain agreement between the simulation and literature experimental data for a high-speed gas jet. The model was applied to simulating the fluidization of fine powders in fluidized beds with an upward or a downward air jet. An empirical cohesion model was obtained by correlating the cohesive force between fine particles using a cohetester. The cohesion model was embedded into the two-fluid model to simulate the fluidization of fine powders in two-dimensional (2-D) beds. To study the fluidization behavior of fine and cohesive powders with a downward jet,experiments were performed in a 2-D bed. Agreement between the computed time-averaged porosity and measured data was obtained. With an upward jet in the bed center, the measured and computed porosities show a dilute central core, especially at very high jet velocities. Based on our experiments and computations, a downward jet located inside the bed is recommended to achieve better mixing and contacting of gas and solids.

  8. Advanced Fine Particulate Characterization Methods

    Energy Technology Data Exchange (ETDEWEB)

    Steven Benson; Lingbu Kong; Alexander Azenkeng; Jason Laumb; Robert Jensen; Edwin Olson; Jill MacKenzie; A.M. Rokanuzzaman

    2007-01-31

    The characterization and control of emissions from combustion sources are of significant importance in improving local and regional air quality. Such emissions include fine particulate matter, organic carbon compounds, and NO{sub x} and SO{sub 2} gases, along with mercury and other toxic metals. This project involved four activities including Further Development of Analytical Techniques for PM{sub 10} and PM{sub 2.5} Characterization and Source Apportionment and Management, Organic Carbonaceous Particulate and Metal Speciation for Source Apportionment Studies, Quantum Modeling, and High-Potassium Carbon Production with Biomass-Coal Blending. The key accomplishments included the development of improved automated methods to characterize the inorganic and organic components particulate matter. The methods involved the use of scanning electron microscopy and x-ray microanalysis for the inorganic fraction and a combination of extractive methods combined with near-edge x-ray absorption fine structure to characterize the organic fraction. These methods have direction application for source apportionment studies of PM because they provide detailed inorganic analysis along with total organic and elemental carbon (OC/EC) quantification. Quantum modeling using density functional theory (DFT) calculations was used to further elucidate a recently developed mechanistic model for mercury speciation in coal combustion systems and interactions on activated carbon. Reaction energies, enthalpies, free energies and binding energies of Hg species to the prototype molecules were derived from the data obtained in these calculations. Bimolecular rate constants for the various elementary steps in the mechanism have been estimated using the hard-sphere collision theory approximation, and the results seem to indicate that extremely fast kinetics could be involved in these surface reactions. Activated carbon was produced from a blend of lignite coal from the Center Mine in North Dakota and

  9. Nanostructured Mg-Al hydrotalcite as catalyst for fine chemical synthesis.

    Science.gov (United States)

    Basahel, Sulaiman N; Al-Thabaiti, Shaeel A; Narasimharao, Katabathini; Ahmed, Nesreen S; Mokhtar, Mohamed

    2014-02-01

    This paper reviews the recent research of nanostructured Mg-Al hydrotalcite (Mg-Al HT) and its application as an efficient solid base catalyst for the synthesis of fine chemicals. Mg-Al HT has many beneficial features, such as low cost, selectivity, catalytic properties, and wide range of preparation and modification methods. They hold promise for providing sought-after, environmentally friendly technologies for the 21st century. Replacement of currently used homogeneous alkaline bases for the synthesis of fine chemicals by a solid catalyst can result in catalyst re-use and waste stream reduction. We introduce briefly the structure, properties and characterization of the nanostructured Mg-Al HT. The efficacy and benign applications of Mg-Al HT as an alternative solid base to homogenous catalysts in the synthesis of fine chemicals are then reviewed. The challenges for the future applications of Mg-Al HT in the synthesis of fine chemicals in terms of green protocol processes are discussed.

  10. Muon Calibration at SoLid

    CERN Document Server

    Saunders, Daniel

    2016-01-01

    The SoLid experiment aims to make a measurement of very short distance neutrino oscillations using reactor antineutrinos. Key to its sensitivity are the experiments high spatial and energy resolution, combined with a very suitable reactor source and efficient background rejection. The fine segmentation of the detector (cubes of side 5cm), and ability to resolve signals in space and time, gives SoLid the capability to track cosmic muons. In principle a source of background, these turn into a valuable calibration source if they can be cleanly identified. This work presents the first energy calibration results, using cosmic muons, of the 288kg SoLid prototype SM1. This includes the methodology of tracking at SoLid, cosmic ray angular analyses at the reactor site, estimates of the time resolution, and calibrations at the cube level.

  11. SOUTHERN FINE PARTICULATE MONITORING PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2002-04-01

    This quarterly report presents results and analysis of continuous onsite ambient fine particulate data at the North Birmingham sampling site during the January-March, 2002 study period. The continuous data include PM{sub 2.5} mass concentrations measured by TEOM, particle sulfate using the R&P 8400S monitor, particle size distributions measured by SMPS and APS monitors, and PM{sub 2.5} light scattering extinction coefficient as measured by nephelometer. Some instrumental issues were noted with the upgrade of the APS model 3320 are described in the report, as well as preliminary performance indications for the upgraded instrument. During the quarter preliminary data analysis and modeling studies were conducted to test the potential of the North Birmingham site data for source attribution analyses. Our initial assessment has continued to be optimistic in this regard due to the location of the site relative to several important classes of local and midrange emission sources. We anticipate that these analyses will provide good separations of the effects of major source classes and spatial source clusters, and will provide useful information relevant to PM{sub 2.5} implementation strategies.

  12. Fine needle aspiration cytology of rectal masses.

    Science.gov (United States)

    Kochhar, R; Rajwanshi, A; Wig, J D; Gupta, N M; Kesiezie, V; Bhasin, D K; Malik, A K; Gupta, S K; Mehta, S K

    1990-01-01

    This paper describes the results of transproctoscopic fine needle aspiration cytology in the diagnosis of rectal lesions. Fifty one consecutive patients referred with a presumptive diagnosis of rectal mass were subjected to proctoscopic examination when fine needle aspiration cytology, brush cytology and biopsy samples were taken. Of the 30 patients of malignancy of rectum in whom all the three sampling techniques were applied, the biopsy was positive in 27 (90%), brush cytology in 25 (83.3%) and fine needle aspiration cytology in 29 (96.6%). A combination of fine needle aspiration cytology with brush cytology gave a positive yield in 96.6% while that fine needle aspiration cytology with brush cytology gave a yield of 100%. Fine needle aspiration cytology was most helpful in infiltrative tumours. All 10 patients with secondaries in the pouch of Douglas or rectovesical pouch, and the single patient with submucosal rectal carcinoma were correctly diagnosed at fine needle aspiration cytology. There were no false positive results with fine needle aspiration cytology and no complications were encountered with the procedure. Images Figure 1 Figure 2 Figure 3 PMID:2323600

  13. 47 CFR 76.943 - Fines.

    Science.gov (United States)

    2010-10-01

    ... TELEVISION SERVICE Cable Rate Regulation § 76.943 Fines. (a) A franchising authority may impose fines or... specifically at the cable operator, provided the franchising authority has such power under state or local laws. (b) If a cable operator willfully fails to comply with the terms of any franchising authority's...

  14. Characterization of Flow Behavior of Semi-Solid Slurries with Low Solid Fractions

    Science.gov (United States)

    Chucheep, Thiensak; Wannasin, Jessada; Canyook, Rungsinee; Rattanochaikul, Tanate; Janudom, Somjai; Wisutmethangoon, Sirikul; Flemings, Merton C.

    2013-10-01

    Semi-solid slurry casting is a metal-forming process that involves transforming liquid metal into slurry having a low solid fraction and then forming the slurry into solid parts. To successfully apply this slurry-forming process, it is necessary to fully understand the flow behavior of semi-solid slurries. This present work applied the rapid quenching method and the modified gravity fluidity casting to investigate the flow behavior, which involves characterizations of the initial solid fraction, fluidity, and microstructure of semi-solid slurries. Three commercial aluminum alloys were used in this study: 383 (Al-Si11Cu), 356 (Al-Si7MgFe), and 7075 (Al-Zn6MgCu) alloys. The results show that the initial solid fractions can be controlled by varying the rheocasting time. The rapid quenching mold can be used to determine the initial solid fractions. In this method, it is important to apply the correcting procedure to account for growth during quenching and to include all the solid phases. Results from the fluidity study of semi-solid slurries show that the fluidity decreases as the initial solid fraction increases. The decrease is relatively rapid near the low end of the initial solid fraction curves, but is quite slow near the high end of the curves. All the three alloys follow this trend. The results also demonstrate that the slurries that contain high solid fractions of up to 30 pct can still flow well. The microstructure characterization results show that the solid particles in the slurries flow uniformly in the channel. A uniform and fine microstructure with limited phase segregation is observed in the slurry cast samples.

  15. Magnetofluidization of fine magnetite powder.

    Science.gov (United States)

    Valverde, J M; Espin, M J; Quintanilla, M A S; Castellanos, A

    2009-03-01

    The behavior of a fluidized bed of fine magnetite particles as affected by a cross-flow magnetic field is investigated. A distinct feature of this naturally cohesive powder, as compared to noncohesive magnetic grains usually employed in magnetofluidized beds, is that the fluidized bed displays a range of stable fluidization even in the absence of an external magnetic field. Upon application of the magnetic field, the interval of stable fluidization is extended to higher gas velocities and bed expansion is enhanced. We have measured the tensile strength as affected by application of the external magnetic field according to two different operation modes. In the H off-on operation mode, the bed is driven to bubbling in the absence of external magnetic field. Once the gas velocity is decreased below the bubbling onset and the bed has returned to stable fluidization due to natural cohesive forces, the field is applied. In the H on-on mode, the field is maintained during the whole process of bubbling and return to stable fluidization. It is found that the tensile strength of the naturally stabilized bed is not essentially changed by application of the field ( H off-on) since the magnetic field cannot alter the bed structure once the particles are jammed in the stable fluidization state. Magnetic forces within the bulk of the jammed bed are partially canceled as a result of the anisotropic nature of the dipole-dipole interaction between the particles, which gives rise to just a small increment of the tensile strength. On the other hand, when the field is held on during bubbling and transition to stable fluidization ( H on-on mode), the tensile strength is appreciably increased. This suggests the formation of particle chains when the particles are not constrained due to the dipole-dipole attractive interaction which affects the mechanical strength of the stably fluidized bed. Experimental data are analyzed in the light of theoretical models on magnetic surface stresses.

  16. A comparative overview of coal-water slurry fuels produced from waste coal fines for utility-scale co-firing applications

    Energy Technology Data Exchange (ETDEWEB)

    Morrison, J.L.; Miller, B.G.; Scaroni, A.W. [Pennsylvania State Univ., University Park, PA (United States)] [and others

    1997-07-01

    The recovery and utilization of coal fines, both impounded and in cleaning plant effluent streams, have received close attention from both coal producers and coal-fixed utilities during the last few years. Many coal producers view impounded fines as an environmental liability and the discarded fines in plant effluent streams as contributing to a loss in Btu recovery. In addition, the rejected coal fines increase the quantity and cost of refuse disposal. The handleability of fine coal has always been a problem. Dewatering cleaned fine coal is costly. Excessive fugitive dust emissions are commonly associated with handling dry fine coal. Wet fine coal sticks to conveyor belts, blocks fuel chutes, and may limit pulverizer capacity. The preparation of coal water slurry fuel (CWSF) from wet coal fines alleviates the necessity of drying while at the same time eliminates the flow problems that wet fine coal poses to the end user. Furthermore, the utilization of CWSF as an opportunity fuel converts coal fines into a revenue source rather than a liability. Several utilities are evaluating the co-firing of low solids, low viscosity CWSF with their normal coal feedstock in an effort to lower fuel cost and/or as a NO{sub x} reduction technique. The utilization of this opportunity fuel is being driven by a changing electric industry in which utilities continually strive to reduce plant emissions while simultaneously reducing their operating costs to become more competitive as the generation side of the industry prepares for deregulation.

  17. Fine Art Fair Held in September

    Institute of Scientific and Technical Information of China (English)

    Guo Yan

    2011-01-01

    "Ihe Art Beijing 2011· Fine Art Fair was held at the National Agricultural Exhibition Center in Beijing from September 15 to 18, 2011. Bringing together over 40 galleries and art institutions, this year's Fine Art Beijing offers a strong lineup. It presented an extraordinary exhibition of both classical and modem art from West and East. Compared with previous fairs, the exhibits at the Fine Art Beijing 2011 are richer in form and more diversified in style. Attending the fair,

  18. Dairy manure resource recovery utilizing two-stage anaerobic digestion - Implications of solids fractionation.

    Science.gov (United States)

    Stowe, Edmond J; Coats, Erik R; Brinkman, Cynthia K

    2015-12-01

    Dairy manure management is increasingly becoming an environmental challenge. In this regard, manure anaerobic digestion (AD) can be applied to address environmental concerns; however, dairy manure AD remains economically uncompetitive. Ongoing research is focused on enhanced resource recovery from manure, including maximizing AD methane yield through a novel multi-stage AD configuration. Research presented herein centered on the hypothesis that separately digesting fine and coarse solids from fermented dairy manure would improve methane production; the hypothesis was disproven. While maximum methane concentration was realized on fine solids, combined solids AD yielded enhanced VS destruction. The diverse combined-solids substrate enriched for a more heterogeneous bacterial/archaeal consortium that balanced fermentation and methanogenesis to yield maximum product (methane). However, results suggest that targeted AD of the fat-rich fine solids could be a more optimal approach for processing manure; alternate (non-AD) methods could then be applied to extract value from the fibrous fraction.

  19. Clustering Dynamics of Ultra-fine Particulate Systems

    Science.gov (United States)

    Dutt, Meenakshi; Elliott, James

    2008-03-01

    Length scales of particles and their surrounding medium strongly determines the nature of their interactions with one another and their responses to external fields. We are interested in systems of ultrafine particles (0.1 - 1.0 micron) such as volcanic ash, solid aerosols, or fine powders for pharmaceutical ihalation applications. We develop a numerical model for these systems using the Derjaguin-Muller-Toporov (DMT) adhesion theory along with the van der Waals attraction between the particles and their contact mechanical interactions. We study the dynamics of these systems in the absence and presence of gravity by controlling the particle size, and thereby, the surface properties of the particles. The high surface energies of these particles causes them to agglomerate as they gravitationally settle. We explore their internal structure as a function of their particle size.

  20. Characterisation of mechanical pulp fines from alkaline peroxide pulping of EFB

    Science.gov (United States)

    Kamaludin, Nurul Hasanah; Ghazali, Arniza; Daud, Wan Rosli Wan

    2012-09-01

    EFB (empty fruit bunch) was subjected to alkaline peroxide pulping for generation of fibrous mass as raw material for the making of pulp-based products. During refining, co-produced fines were collected by fractionation on square-mesh screens of 200-, 250-, 300- and 400- mesh sizes, placed at the refining discharge by order of increasing mesh. Each set of the produced paper was incorporated with 12% fines for microscopic analysis. It appears that sheared vessel elements and fibrils were predominant and they make up the mass rendering collapsibility of cell wall for good product formation. The study acknowledged the form of fines functioning as natural filler in pulp network and worthy of utilization for reduction of total suspended solid.

  1. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.

  2. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    Nebera; A.; Markusbkin; Yu.; Azarov; V.; Ermolaev; N.

    2005-01-01

    Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.……

  3. DESIGN INFORMATION ON FINE PORE AERATION SYSTEMS

    Science.gov (United States)

    Field studies were conducted over several years at municipal wastewater treatment plants employing line pore diffused aeration systems. These studies were designed to produce reliable information on the performance and operational requirements of fine pore devices under process ...

  4. NEW RSW & Wall Fine Fully Tetrahedral Grid

    Data.gov (United States)

    National Aeronautics and Space Administration — NEW RSW Fine Fully Tetrahedral Grid with Viscous Wind Tunnel wall at the root. This grid is for a node-based unstructured solver. Note that the CGNS file is very...

  5. NEW RSW & Wall Fine Mixed Element Grid

    Data.gov (United States)

    National Aeronautics and Space Administration — RSW Fine Mixed Element Grid with viscous root wind tunnel wall. This grid is for a node-based unstructured solver. Quad Surface Faces= 38016 Tria Surface Faces=...

  6. Immobilization of Rocky Flats Graphite Fines Residue

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, T.S.

    1999-04-06

    The development of the immobilization process for graphite fines has proceeded through a series of experimental programs. The experimental procedures and results from each series of experiments are discussed in this report.

  7. Fine 5 Eesti tantsuväljal / Iiris Viirpalu

    Index Scriptorium Estoniae

    Viirpalu, Iiris, 1992-

    2017-01-01

    Nüüdistantsuteatril Fine 5 täitub tänavu 25. tegutsemisaasta. Fine 5 käekirjast. Vestlusest Fine 5 tantsuteatri ja -kooli kauaaegsete kunstiliste juhtide Renee Nõmmiku ja Tiina Olleskiga Eesti tantsukunstist

  8. Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid

    Science.gov (United States)

    ... Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid An ultrasound-guided thyroid biopsy uses sound waves ... Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid? During a fine needle aspiration biopsy of the ...

  9. Morphological study of Sr2CeO4 blue phosphor with fine particles

    Directory of Open Access Journals (Sweden)

    Janaína Gomes

    2004-10-01

    Full Text Available Morphological and spectroscopic studies of Sr2CeO4 blue phosphor in the form of fine particles prepared from a powdered multi-component precursor, via a combustion method, are reported. Samples were also prepared through a solid-state reaction and from a polymeric precursor for comparison. Citric acid or glycine as fuels in the combustion method lead to a mixture which is heated at 950 ºC for 4 h, resulting in spheroidal particles with a diameter between 250-550 nm. Samples from the polymeric precursor result in spheroidal particles (350-550 nm and from the solid-state reaction in irregular particles (~ 5 mum. Therefore, the combustion method is adequate for preparation of Sr2CeO4 in the form of spherical fine particles.

  10. Modeling of Fine-Particle Formation in Turbulent Flames

    Science.gov (United States)

    Raman, Venkat; Fox, Rodney O.

    2016-01-01

    The generation of nanostructured particles in high-temperature flames is important both for the control of emissions from combustion devices and for the synthesis of high-value chemicals for a variety of applications. The physiochemical processes that lead to the production of fine particles in turbulent flames are highly sensitive to the flow physics and, in particular, the history of thermochemical compositions and turbulent features they encounter. Consequently, it is possible to change the characteristic size, structure, composition, and yield of the fine particles by altering the flow configuration. This review describes the complex multiscale interactions among turbulent fluid flow, gas-phase chemical reactions, and solid-phase particle evolution. The focus is on modeling the generation of soot particles, an unwanted pollutant from automobile and aircraft engines, as well as metal oxides, a class of high-value chemicals sought for specialized applications, including emissions control. Issues arising due to the numerical methods used to approximate the particle number density function, the modeling of turbulence-chemistry interactions, and model validation are also discussed.

  11. Magnetic properties of lanthanum orthoferrite fine powders prepared by different chemical routes

    Indian Academy of Sciences (India)

    Benedict Ita; P Murugavel; V Ponnambalam; A R Raju

    2003-10-01

    Fine powders of lanthanum iron oxide, LaFeO3, have been prepared by solid state reaction as well as sol-gel synthesis and nebulized spray pyrolysis. Structures, morphologies and magnetic susceptibility measurements of these powders have been examined. The powders prepared by all the three low-temperature routes contain nearly spherical particles with an average diameter of 40 nm. These samples show a lower Neel temperature than the powder prepared by solid state reaction besides showing much lower magnetic susceptibility at low temperatures.

  12. Modeling the injection of gas-liquid jets into fluidized bed of fine particles

    Energy Technology Data Exchange (ETDEWEB)

    Aryiapadi, S.; Berutti, F.; Briens, C.; Hulet, C. [Western Ontario University, Dept. of Chemical and Biochemical Engineeering, London, ON (Canada); Griffith, P. [Massachussetts Institute of Technology, Dept. of Mechanical Engineering, Cambridge, MA (United States)

    2003-08-01

    A simplified momentum-based approach to calculate the solid entrainment rate into a gas-liquid jet injected into a fluidized bed is described. The model is verified by a recently developed experimental technique. The paper also addresses correction factors to the initial momentum calculated from the homogenous model. The solids entrainment rates predicted by the model were found to be very close to experimentally obtained values. It is suggested that the model can be usefully employed in characterizing the behaviour of gas-liquid jets injected into fluidized beds of fine particles. 21 refs., 8 figs.

  13. Mass, energy and material balances of SRF production process. Part 3: solid recovered fuel produced from municipal solid waste.

    Science.gov (United States)

    Nasrullah, Muhammad; Vainikka, Pasi; Hannula, Janne; Hurme, Markku; Kärki, Janne

    2015-02-01

    This is the third and final part of the three-part article written to describe the mass, energy and material balances of the solid recovered fuel production process produced from various types of waste streams through mechanical treatment. This article focused the production of solid recovered fuel from municipal solid waste. The stream of municipal solid waste used here as an input waste material to produce solid recovered fuel is energy waste collected from households of municipality. This article presents the mass, energy and material balances of the solid recovered fuel production process. These balances are based on the proximate as well as the ultimate analysis and the composition determination of various streams of material produced in a solid recovered fuel production plant. All the process streams are sampled and treated according to CEN standard methods for solid recovered fuel. The results of the mass balance of the solid recovered fuel production process showed that 72% of the input waste material was recovered in the form of solid recovered fuel; 2.6% as ferrous metal, 0.4% as non-ferrous metal, 11% was sorted as rejects material, 12% as fine faction and 2% as heavy fraction. The energy balance of the solid recovered fuel production process showed that 86% of the total input energy content of input waste material was recovered in the form of solid recovered fuel. The remaining percentage (14%) of the input energy was split into the streams of reject material, fine fraction and heavy fraction. The material balances of this process showed that mass fraction of paper and cardboard, plastic (soft) and wood recovered in the solid recovered fuel stream was 88%, 85% and 90%, respectively, of their input mass. A high mass fraction of rubber material, plastic (PVC-plastic) and inert (stone/rock and glass particles) was found in the reject material stream. © The Author(s) 2014.

  14. Revisiting fine-tuning in the MSSM

    Science.gov (United States)

    Ross, Graham G.; Schmidt-Hoberg, Kai; Staub, Florian

    2017-03-01

    We evaluate the amount of fine-tuning in constrained versions of the minimal supersymmetric standard model (MSSM), with different boundary conditions at the GUT scale. Specifically we study the fully constrained version as well as the cases of non-universal Higgs and gaugino masses. We allow for the presence of additional non-holomorphic soft-terms which we show further relax the fine-tuning. Of particular importance is the possibility of a Higgsino mass term and we discuss possible origins for such a term in UV complete models. We point out that loop corrections typically lead to a reduction in the fine-tuning by a factor of about two compared to the estimate at tree-level, which has been overlooked in many recent works. Taking these loop corrections into account, we discuss the impact of current limits from SUSY searches and dark matter on the fine-tuning. Contrary to common lore, we find that the MSSM fine-tuning can be as small as 10 while remaining consistent with all experimental constraints. If, in addition, the dark matter abundance is fully explained by the neutralino LSP, the fine-tuning can still be as low as ˜ 20 in the presence of additional non-holomorphic soft-terms. We also discuss future prospects of these models and find that the MSSM will remain natural even in the case of a non-discovery in the foreseeable future.

  15. Pelletization of fine coals. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, K.V.S.

    1995-12-31

    Coal is one of the most abundant energy resources in the US with nearly 800 million tons of it being mined annually. Process and environmental demands for low-ash, low-sulfur coals and economic constraints for high productivity are leading the coal industry to use such modern mining methods as longwall mining and such newer coal processing techniques as froth flotation, oil agglomeration, chemical cleaning and synthetic fuel production. All these processes are faced with one common problem area--fine coals. Dealing effectively with these fine coals during handling, storage, transportation, and/or processing continues to be a challenge facing the industry. Agglomeration by the unit operation of pelletization consists of tumbling moist fines in drums or discs. Past experimental work and limited commercial practice have shown that pelletization can alleviate the problems associated with fine coals. However, it was recognized that there exists a serious need for delineating the fundamental principles of fine coal pelletization. Accordingly, a research program has been carried involving four specific topics: (i) experimental investigation of coal pelletization kinetics, (ii) understanding the surface principles of coal pelletization, (iii) modeling of coal pelletization processes, and (iv) simulation of fine coal pelletization circuits. This report summarizes the major findings and provides relevant details of the research effort.

  16. An enhanced-gravity method to recover ultra-fine coal from tailings: Falcon concentrator

    Energy Technology Data Exchange (ETDEWEB)

    Filiz Oruc; Selcuk Ozgen; Eyup Sabah [Afyon Kocatepe University, Afyonkarahisar (Turkey). Department of Mining Engineering

    2010-09-15

    The Falcon concentrator is an enhanced-gravity separator used for the concentration of fine and ultra-fine minerals. This study was conducted to evaluate the effects of different process variables on the performance of the Falcon SB-40 concentrator for beneficiation of tailings to recover ultra-fine coal. Various operating and design conditions such as bowl speed (G force), water pressure, pulp solid ratio and pulp feed rate were investigated. A hydrocyclone was used for pre-enrichment with the Falcon concentrator. Operation parameters of the hydrocyclone, namely feed solids, inlet pressure, vortex finder and apex diameters were investigated. In order to produce fine coal concentrates, regression equations were derived by applying the least squares method using Minitab 15 software. Response functions were produced for the ash content and the recovery of the clean coal concentrates for the performance of the hydrocyclone and Falcon concentrator under different operating conditions. Predicted values were found with the experimental values giving R{sup 2} values of between 0.73 and 0.58 for ash content and between 0.65 and 0.39 for recovery of the clean coal. It was shown that under optimized conditions the Falcon concentrator can produce a clean coal with an ash value of 36% from a feed coal of about 66% ash. 19 refs., 7 figs., 5 tabs.

  17. Improvement in SOFC anode performance by finely-structured Ni/YSZ cermet prepared via heterocoagulation.

    Science.gov (United States)

    Sunagawa, Yoji; Yamamoto, Katsutoshi; Muramatsu, Atsushi

    2006-03-30

    A novel preparation technique for a nanostructured anode for a solid oxide fuel cell is investigated. By mixing nanometer-sized NiO and YSZ powders in a pH-controlled aqueous media, a fine mixture of nanoparticles is successfully obtained through heterocoagulation. The anode prepared from thus prepared mixture has a large triple phase boundary and shows a great improvement in the anode performance by increasing the electric conductivity and effective surface area.

  18. Statics of deformable solids

    CERN Document Server

    Bisplinghoff, Raymond L; Pian, Theodore HH

    2014-01-01

    Profusely illustrated exposition of fundamentals of solid mechanics and principles of mechanics, statics, and simple statically indeterminate systems. Covers strain and stress in three-dimensional solids, elementary elasticity, energy principles in solid continuum, and more. 1965 edition.

  19. Transition metals in coarse, fine, very fine and ultra-fine particles from an interstate highway transect near Detroit

    Science.gov (United States)

    Cahill, Thomas A.; Barnes, David E.; Lawton, Jonathan A.; Miller, Roger; Spada, Nicholas; Willis, Robert D.; Kimbrough, Sue

    2016-11-01

    As one component of a study investigating the impact of vehicle emissions on near-road air quality, human exposures, and potential health effects, particles were measured from September 21 to October 30, 2010 on both sides of a major roadway (Interstate-96) in Detroit. Traffic moved freely on this 12 lane freeway with a mean velocity of 69 mi/hr. with little braking and acceleration. The UC Davis DELTA Group rotating drum (DRUM) impactors were used to collect particles in 8 size ranges at sites nominally 100 m south, 10 m north, 100 m north, and 300 m north of the highway. Ultra-fine particles were continuously collected at the 10 m north and 100 m north sites. Samples were analyzed every 3 h for mass (soft beta ray transmission), 42 elements (synchrotron-induced x-ray fluorescence) and optical attenuation (350-800 nm spectroscopy). A three day period of steady southerly winds along the array allowed direct measurement of freeway emission rates for coarse (10 > Dp > 1.0 μm), PM2.5, very fine (0.26 > Dp > 0.09 μm), and ultra-fine (Dp car and truck emission rates of 1973, this value would have been about 16 μg/m3, corrected down from the 19 μg/m3 PM5.0 using measured roadway dust contributions. This would have included 2.7 μg/m3 of lead, versus the 0.0033 μg/m3 measured. Very fine particles were distributed across the array with a relatively weak falloff versus distance. For the ultra-fine particles, emissions of soot and metals seen in vehicular braking studies correlated with traffic at the 10 m site, but only the soot was statistically significant at the 100 m north site. Otherwise, the 10 m north and 100 m north sites were essentially identical in mean concentration and highly correlated in time for most of the 5 week study. This result supports earlier publications showing the ability of very fine and ultra-fine particles to transport to sites well removed from the freeway sources. The concentrations of very fine and ultra-fine metals from brake wear and

  20. Platonic solids back in the sky: Icosahedral inflation

    CERN Document Server

    Kang, Jonghee

    2015-01-01

    We generalize the model of solid inflation to an anisotropic cosmic solid. Barring fine tunings, the observed isotropy of the cosmological background and of the scalar two-point function isolate the icosahedral group as the only possible symmetry group of such a solid. In such a case, higher-point correlation functions---starting with the three-point one---are naturally maximally anisotropic, which makes the standard detection strategies highly inefficient and calls for a dedicated analysis of CMB data. The tensor two-point function can also be highly anisotropic, but only in the presence of sizable higher-derivative couplings.

  1. Charge neutrality of fine particle (dusty) plasmas and fine particle cloud under gravity

    Science.gov (United States)

    Totsuji, Hiroo

    2017-03-01

    The enhancement of the charge neutrality due to the existence of fine particles is shown to occur generally under microgravity and in one-dimensional structures under gravity. As an application of the latter, the size and position of fine particle clouds relative to surrounding plasmas are determined under gravity.

  2. 76 FR 31307 - Commission of Fine Arts; Notice of Meeting

    Science.gov (United States)

    2011-05-31

    ... From the Federal Register Online via the Government Publishing Office COMMISSION OF FINE ARTS Commission of Fine Arts; Notice of Meeting The next meeting of the U.S. Commission of Fine Arts is scheduled... oral statements should be addressed to Thomas Luebke, Secretary, U.S. Commission of Fine Arts, at...

  3. Towards gloss control in fine art reproduction

    Science.gov (United States)

    Baar, Teun; Brettel, Hans; Ortiz Segovia, Maria V.

    2015-03-01

    The studies regarding fine art reproduction mainly focus on the accuracy of colour and the recreation of surface texture properties. Since reflection properties other than colour are neglected, important details of the artwork are lost. For instance, gloss properties, often characteristic to painters and particular movements in the history of art, are not well reproduced. The inadequate reproduction of the different gloss levels of a piece of fine art leads to a specular reflection mismatch in printed copies with respect to the original works that affects the perceptual quality of the printout. We used different print parameters of a 3D high resolution printing setup to control the gloss level on a printout locally. Our method can be used to control gloss automatically and in crucial applications such as fine art reproduction.

  4. The fluidity of boulder debris flows is affected by fine sediment in the pore water

    Science.gov (United States)

    Hotta, Norifumi; Kaneko, Takahiro; Iwata, Tomoyuki; Nishimoto, Haruo

    2013-04-01

    Basic equations for debris flows are frequently derived using the simple assumption of monogranular particles. However, actual debris flows include a great diversity of grain sizes, resulting in inherent features such as inverse grading, particle size segregation, and liquefaction of fine sediment. The liquefaction of fine sediment affects the fluidity of debris flows, although the behavior and influence of fine sediment in debris flows have not been examined sufficiently. This study used flume tests to detect the effect of fine sediment on the characteristics of laboratory debris flows consisting of particles with two diameters: one diameter was fixed at a large particle size, while the small diameters were varied with the experimental conditions. From the experiments, the greatest sediment concentration and flow depth were observed in the debris flows mixed with finer sediment, indicating increased flow resistance. Then, the experimental friction coefficient was compared with the theoretical friction coefficient derived by substituting the experimental values into the constitutive equations for debris flow. The theoretical friction coefficient was obtained from two models with different fine-sediment treatments: one assuming that all of the fine sediments were solid particles and the other that the particles consisted of a fluid phase involving pore water liquefaction. A discriminant index was introduced to clarify which contribution from the two models could better explain the experimental results. The comparison of the friction coefficients detected a fully liquefied state for the finest particle mixture with sediment. However, even with the same particle size, the debris flows could be regarded as a liquefied state, a solid state, or a partially liquefied transition state depending on the experimental conditions other than the sediment particle size. These results infer that the liquefaction of fine sediment in debris flows was induced not only by the

  5. Solid lubricants and surfaces

    CERN Document Server

    Braithwaite, E R

    1964-01-01

    Solid Lubricants and Surfaces deals with the theory and use of solid lubricants, particularly in colloidal form. Portions of this book are devoted to graphite and molybdenum disulfides, which are widely used solid lubricants in colloidal form. An extensive literature on the laboratory examination of hundreds of solids as potential lubricants is also provided in this text. Other topics discussed include the metals and solid lubricants; techniques for examining surfaces; other solid lubricants; metal shaping; and industrial uses of solid-lubricant dispersions. This publication is beneficial to e

  6. Fine-grained concrete with organomineral additive

    Directory of Open Access Journals (Sweden)

    Solovyov Vitaly

    2016-01-01

    Full Text Available The article deals with the issues concerning the formation of the structure and properties of fine-grained concrete with organomineral additive produced through mechanochemical activation of thermal power plant fly ash together with superplasticizer. The additive is produced in a high-speed activator at the collision particles’ speed of about 80 m/s. The use of the additive in fine-grained concrete in the amounts of 0.5-1% increased the strength by 30-50% and reduced the size and volume of pores. The cement consumption in such concrete is close to the cement consumption in common concrete of equal resistance.

  7. Dewatering of fine coal using hyperbaric centrifugation

    Energy Technology Data Exchange (ETDEWEB)

    Ramazan Asmatulu; Gerald H. Luttrell; Roe-Hoan Yoon [Virginia Polytechnic Institute and State University, Blacksburg, VA (US). Center for Advanced Separation Technologies

    2005-09-01

    Many coal preparation plants are forced to discard their fine coal because of the inability of existing technologies to reduce the moisture content of this product to an acceptable level. In an effort to overcome this problem, a new mechanical dewatering method has been developed that combines centrifugation with pressure filtration. The process, which may be referred to as hyperbaric centrifugation, is capable of producing a drier product than can be achieved using either filtration or centrifugation alone. The test data obtained from batch experiments show that the new method can reduce cake moisture to 10% or below for many fine coal product streams.

  8. [Combustion temperature measurement of solid propellant and the effect of organic compound on combustion temperature].

    Science.gov (United States)

    Zhou, Xue-tie; Li, Yan; Chen, Zuo-ru; Wang, Jun-de

    2003-06-01

    The FTIR emission spectra in the spectral range of 4,500-300 cm-1 for the solid propellants were measured by a remote sensing FTIR system. The P-branch of fine structure of HCl fundamental band lying at 3.46 microns was used for precise combustion temperature measurement of the solid propellant. The effect of the organic compound in the solid propellant on the combustion temperature was discussed.

  9. Organic chemistry on solid surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Zhen; Zaera, Francisco [Department of Chemistry, University of California, Riverside, CA 92521 (United States)

    2006-07-15

    Chemistry on solid surfaces is central to many areas of practical interest such as heterogeneous catalysis, tribology, electrochemistry, and materials processing. With the development of many surface-sensitive analytical techniques in the past decades, great advances have been possible in our understanding of such surface chemistry at the molecular level. Earlier studies with model systems, single crystals in particular, have provided rich information about the adsorption and reaction kinetics of simple inorganic molecules. More recently, the same approach has been expanded to the study of the surface chemistry of relatively complex organic molecules, in large measure in connection with the selective synthesis of fine chemicals and pharmaceuticals. In this report, the chemical reactions of organic molecules and fragments on solid surfaces, mainly on single crystals of metals but also on crystals of metal oxides, carbides, nitrides, phosphides, sulfides and semiconductors as well as on more complex models such as bimetallics, alloys, and supported particles, are reviewed. A scheme borrowed from the organometallic and organic chemistry literature is followed in which key examples of representative reactions are cited first, and general reactivity trends in terms of both the reactants and the nature of the surface are then identified to highlight important mechanistic details. An attempt has been made to emphasize recent advances, but key earlier examples are cited as needed. Finally, correlations between surface and organometallic and organic chemistry, the relevance of surface reactions to applied catalysis and materials functionalization, and some promising future directions in this area are briefly discussed. (author)

  10. Pollution Standards, Costly Monitoring and Fines

    NARCIS (Netherlands)

    Arguedas, C.

    2005-01-01

    We investigate the features of optimal regulatory policies composed of pollution standards and probabilities of inspection, where fines for non-compliance depend not only on the degree of violation but alson on nongravity factors.We show that optimal policies can induce either compliance or noncompl

  11. Testing with fine fragrances in eczema patients

    DEFF Research Database (Denmark)

    Johansen, J D; Frosch, Peter J; Rastogi, Suresh Chandra

    2001-01-01

    The frequencies of contact allergic reactions to 2 fine fragrances were studied by patch testing. Further, a comparison was made of test results before and after evaporation of the solvent. A total of 480 consecutive eczema patients were included, 100 in the Dortmund clinic and 380 in the Gentoft...

  12. The fine structure of the ionosphere

    DEFF Research Database (Denmark)

    D'Angelo, N.; Michelsen, Poul

    1967-01-01

    We consider in this note the excitation of ion-acoustic waves by vertical gradients of density in the ionosphere. The conclusion is reached that the fine structure of the ionosphere is probably affected by the resulting instability, as comparison with observations seems to indicate. Recently, Liu...

  13. Alkaline Hydrolysis Conversion of Nitrocellulose Fines

    Science.gov (United States)

    1997-10-01

    The conversion of 1,125,000 pounds of bone-dry nitrocellulose fines into a liquid fertilizer was documented. Alkaline hydrolysis was the conversion... fertilizer . Fertilizer nutrient value was 1.3% nitrogen (N), 8.0% potassium (K2O) and 0.9% phosphorus (P2O5). Conversion met all applicable federal and state safety and environmental regulations.

  14. Pollution Standards, Costly Monitoring and Fines

    NARCIS (Netherlands)

    Arguedas, C.

    2005-01-01

    We investigate the features of optimal regulatory policies composed of pollution standards and probabilities of inspection, where fines for non-compliance depend not only on the degree of violation but alson on nongravity factors.We show that optimal policies can induce either compliance or

  15. Fine fuel heating by radiant flux

    Science.gov (United States)

    David Frankman; Brent W. Webb; Bret W. Butler; Don J. Latham

    2010-01-01

    Experiments were conducted wherein wood shavings and Ponderosa pine needles in quiescent air were subjected to a steady radiation heat flux from a planar ceramic burner. The internal temperature of these particles was measured using fine diameter (0.076mm diameter) type K thermocouples. A narrow angle radiometer was used to determine the emissive power generated by the...

  16. The fine structure constant and habitable planets

    DEFF Research Database (Denmark)

    Sandora, McCullen

    2016-01-01

    © 2016 IOP Publishing Ltd and Sissa Medialab srl .We use the existence of habitable planets to impose anthropic requirements on the fine structure constant, α. To this effect, we present two considerations that restrict its value to be very near the one observed. The first, that the end product...

  17. Facilities Guidelines for Fine Arts Programs.

    Science.gov (United States)

    Maryland State Dept. of Education, Baltimore.

    This manual of facility guidelines examines the planning process and design features and considerations for public school fine arts programs in Maryland. Planning concepts and trends are highlighted followed by planning guidelines for dance, music, theater, visual arts, general education, and performance spaces. General design considerations…

  18. Approximation properties of fine hyperbolic graphs

    Indian Academy of Sciences (India)

    Benyin Fu

    2016-05-01

    In this paper, we propose a definition of approximation property which is called the metric invariant translation approximation property for a countable discrete metric space. Moreover, we use the techniques of Ozawa’s to prove that a fine hyperbolic graph has the metric invariant translation approximation property.

  19. Development of an Ultra-fine Coal Dewatering Technology and an Integrated Flotation-Dewatering System for Coal Preparation Plants

    Energy Technology Data Exchange (ETDEWEB)

    Wu Zhang; David Yang; Amar Amarnath; Iftikhar Huq; Scott O' Brien; Jim Williams

    2006-12-22

    The project proposal was approved for only the phase I period. The goal for this Phase I project was to develop an industrial model that can perform continuous and efficient dewatering of fine coal slurries of the previous flotation process to fine coal cake of {approx}15% water content from 50-70%. The feasibility of this model should be demonstrated experimentally using a lab scale setup. The Phase I project was originally for one year, from May 2005 to May 2006. With DOE approval, the project was extended to Dec. 2006 without additional cost from DOE to accomplish the work. Water has been used in mining for a number of purposes such as a carrier, washing liquid, dust-catching media, fire-retardation media, temperature-control media, and solvent. When coal is cleaned in wet-processing circuits, waste streams containing water, fine coal, and noncombustible particles (ash-forming minerals) are produced. In many coal preparation plants, the fine waste stream is fed into a series of selection processes where fine coal particles are recovered from the mixture to form diluted coal fine slurries. A dewatering process is then needed to reduce the water content to about 15%-20% so that the product is marketable. However, in the dewatering process currently used in coal preparation plants, coal fines smaller than 45 micrometers are lost, and in many other plants, coal fines up to 100 micrometers are also wasted. These not-recovered coal fines are mixed with water and mineral particles of the similar particle size range and discharged to impoundment. The wasted water from coal preparation plants containing unrecoverable coal fine and mineral particles are called tailings. With time the amount of wastewater accumulates occupying vast land space while it appears as threat to the environment. This project developed a special extruder and demonstrated its application in solid-liquid separation of coal slurry, tailings containing coal fines mostly less than 50 micron. The

  20. Fine root production at drained peatland sites

    Energy Technology Data Exchange (ETDEWEB)

    Finer, L. [Finnish Forest Research Inst. (Finland). Joensuu Research Station; Laine, J. [Helsinki Univ. (Finland). Dept. of Forest Ecology

    1996-12-31

    The preliminary results of the Finnish project `Carbon balance of peatlands and climate change` show that fine roots play an important role in carbon cycling on peat soils. After drainage the roots of mire species are gradually replaced by the roots of trees and other forest species. Pine fine root biomass reaches a maximum level by the time of crown closure, some 20 years after drainage on pine mire. The aim of this study is to compare the results of the sequential coring method and the ingrowth bag method used for estimating fine root production on three drained peatland sites of different fertility. The results are preliminary and continuation to the work done in the study Pine root production on drained peatlands, which is part of the Finnish project `Carbon cycling on peatlands and climate change`. In this study the fine root biomass was greater on the poor site than on the rich sites. Pine fine root production increased with the decrease in fertility. Root turnover and the production of field layer species were greater on the rich sites than on the poor site. The results suggested that the in growth bag method measured more root activity than the magnitude of production. More than two growing seasons would have been needed to balance the root dynamics in the in growth bags with the surrounding soil. That time would probably have been longer on the poor site than on the rich ones and longer for pine and field layer consisting of dwarf shrubs than for field layer consisting of sedge like species and birch. (11 refs.)

  1. CONTACT STRENGTH OF MECHANOACTIVATED FINE CONCRETES FROM GRANULATED BLAST-FURNACE SLAGS

    Directory of Open Access Journals (Sweden)

    V. I. Bolshakov

    2014-10-01

    rotary mixer-activator on the value of the contact strength of cement and aggregates got further development. Practical value. Strengthening of contact area of fine concrete in the exercise of the combined machining of all concrete mix components in the mixer-activator is achieved owing to increment of hydration degree of raw concrete components; creation of conditions for solid-phase chemical reactions between its components; structure improvement of the received material. It promotes significant increase of mechanical strength of mechanoactivated fine concretes (around 5 times in comparison with concretes, made from a non-activated mix, which makes it possible to decrease the cement consumption when manufacturing 1 m3 of concrete up to 59 %.

  2. Synthesis of LiBOB Fine Powder to Increase Solubility

    Directory of Open Access Journals (Sweden)

    Etty Marti Wigayati

    2017-04-01

    Full Text Available Lithium bis (oxalate borate or LiBOB compound has captured interest of researchers, because it is potentially viable to be used as electrolyte salt in lithium-ion battery system. This compound is easy to synthesize and considered to be more environmentally friendly compared to conventional electrolyte salt because LiBOB does not contain halogen element. This research focused on the synthesis of LiBOB fine powder, which main purpose is improving LiBOB salt solubility in liquid electrolyte solution. This will aid the ion transfer between electrodes which in turn will increase the electrolyte performance. Solid state reaction was employed in this experiment. Synthesis of LiBOB compound was performed by reacting oxalic acid dihydrate, lithium hydroxide monohydrate, and boric acid. The resulting powder was then processed into fine powder using ball milling technique with varying milling time (0, 6, 10, and 13 hour. Microstructure of the sample was then analyzed to obtain information regarding phase formation, functional groups, grain surface morphology, surface area, pore volume, solubility, and ionic conductivity. The analysis shown that LiBOB and LiBOB hydrate phase was formed during the reaction, there was no changed in existing phase during milling process, crystallinity index was shifted to lower value but there was no difference in functional groups. Highest value in surface area was found to be 83.11 m2/g, with pore volume of 1.21311e+02 A at 10 hours milling. Smaller powder size resulted in higher solubility, unfortunately the ionic conductivity was found to be decreased.

  3. Sample Results from MCU Solids Outage

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T.; Washington, A.; Oji, L.; Coleman, C.; Poirier, M.

    2014-09-22

    Savannah River National Laboratory (SRNL) has received several solid and liquid samples from MCU in an effort to understand and recover from the system outage starting on April 6, 2014. SRNL concludes that the presence of solids in the Salt Solution Feed Tank (SSFT) is the likely root cause for the outage, based upon the following discoveries: A solids sample from the extraction contactor #1 proved to be mostly sodium oxalate; A solids sample from the scrub contactor#1 proved to be mostly sodium oxalate; A solids sample from the Salt Solution Feed Tank (SSFT) proved to be mostly sodium oxalate; An archived sample from Tank 49H taken last year was shown to contain a fine precipitate of sodium oxalate; A solids sample from ; A liquid sample from the SSFT was shown to have elevated levels of oxalate anion compared to the expected concentration in the feed. Visual inspection of the SSFT indicated the presence of precipitated or transferred solids, which were likely also in the Salt Solution Receipt Tank (SSRT). The presence of the solids coupled with agitation performed to maintain feed temperature resulted in oxalate solids migration through the MCU system and caused hydraulic issues that resulted in unplanned phase carryover from the extraction into the scrub, and ultimately the strip contactors. Not only did this carryover result in the Strip Effluent (SE) being pushed out of waste acceptance specification, but it resulted in the deposition of solids into several of the contactors. At the same time, extensive deposits of aluminosilicates were found in the drain tube in the extraction contactor #1. However it is not known at this time how the aluminosilicate solids are related to the oxalate solids. The solids were successfully cleaned out of the MCU system. However, future consideration must be given to the exclusion of oxalate solids into the MCU system. There were 53 recommendations for improving operations recently identified. Some additional considerations or

  4. Solid state physics

    CERN Document Server

    Burns, Gerald

    2013-01-01

    Solid State Physics, International Edition covers the fundamentals and the advanced concepts of solid state physics. The book is comprised of 18 chapters that tackle a specific aspect of solid state physics. Chapters 1 to 3 discuss the symmetry aspects of crystalline solids, while Chapter 4 covers the application of X-rays in solid state science. Chapter 5 deals with the anisotropic character of crystals. Chapters 6 to 8 talk about the five common types of bonding in solids, while Chapters 9 and 10 cover the free electron theory and band theory. Chapters 11 and 12 discuss the effects of moveme

  5. Theoretical solid state physics

    CERN Document Server

    Haug, Albert

    2013-01-01

    Theoretical Solid State Physics, Volume 1 focuses on the study of solid state physics. The volume first takes a look at the basic concepts and structures of solid state physics, including potential energies of solids, concept and classification of solids, and crystal structure. The book then explains single-electron approximation wherein the methods for calculating energy bands; electron in the field of crystal atoms; laws of motion of the electrons in solids; and electron statistics are discussed. The text describes general forms of solutions and relationships, including collective electron i

  6. Coagulation settling characteristics and eliminating pollution analysis of fine-grind natural zeolite in static and turbulent flow.

    Science.gov (United States)

    Zhu, Ruirui; Zhu, Jianzhong; Chen, Liang

    2014-05-01

    The phenomenon of coagulation settling in liquid suspensions has a variety of applications, including mineral processing, treatment of industrial effluents, and municipal sewage sludge purification. This study was to investigate the coagulation settling characteristics of fine-grind natural zeolite and evaluate the removal efficiency of contaminants simultaneously in static and turbulent flow. A series of column experiments were conducted to pattern the characteristics of spatial and temporal variation of coagulation settling and removal contaminants in static and turbulent flow. The results indicated that the suspended solid concentration presented an apparent exponential decay with coagulation settling time in static flow (R (2)  > 0.99), coagulation settling rate of the fine zeolite-suspended solid in static flow was between 0.005 and 0.05 cm/s obtained from the repeat depth suction method. The relation between average C/C 0 of pollutants and suspended solid concentration was exponential before the settlement for 24 h and that was the line after the settlement for 24 h. Several various models were presented to highlight the coagulation settling characteristics of fine-grind natural zeolite in static and turbulent flow. Compared to hydrostatic settling experiments, zeolite-suspended solid presented better removal efficiency of pollutants and greater removal rate of pollutants in turbulent flow.

  7. What Are Solid Fats?

    Science.gov (United States)

    ... fatty acids. Most solid fats are high in saturated fats and/or trans fats and have less monounsaturated ... Animal products containing solid fats also contain cholesterol. Saturated fats and trans fats tend to raise "bad" (LDL) ...

  8. Tetraphenylborate Solids Stability Tests

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D.D. [Westinghouse Savannah River Company, AIKEN, SC (United States)

    1997-06-25

    Tetraphenylborate solids are a potentially large source of benzene in the slurries produced in the In-Tank Precipitation (ITP) process. The stability of the solids is an important consideration in the safety analysis of the process and we desire an understanding of the factors that influence the rate of conversion of the solids to benzene. This report discusses current testing of the stability of tetraphenylborate solids.

  9. Laser cooling of solids

    Energy Technology Data Exchange (ETDEWEB)

    Epstein, Richard I [Los Alamos National Laboratory; Sheik-bahae, Mansoor [UNM

    2008-01-01

    We present an overview of solid-state optical refrigeration also known as laser cooling in solids by fluorescence upconversion. The idea of cooling a solid-state optical material by simply shining a laser beam onto it may sound counter intuitive but is rapidly becoming a promising technology for future cryocooler. We chart the evolution of this science in rare-earth doped solids and semiconductors.

  10. Dewatering studies of fine clean coal

    Energy Technology Data Exchange (ETDEWEB)

    Parekh, B.K.

    1991-01-01

    Physical cleaning of ultra-fine coal using an advanced froth flotation technique provides a low ash product, however, the amount of water associated with clean coal is high. Economic removal of water from the froth will be important for commercial applicability of advanced froth flotation processes. The main objective of the present research program is to study and understand the dewatering characteristics of ultra-fine clean coal and to develop the process parameters to effectively reduce the moisture to less than 20 percent in the clean coal product. The research approach under investigation utilizes synergistic effects of metal ions and surfactant to lower the moisture of clean coal using a conventional vacuum dewatering technique. During the last year's effort, it was reported that a combination of metal ion and surfactant provided a 22 percent moisture filter cake.

  11. Interaction between Escherichia coli and lunar fines

    Science.gov (United States)

    Johansson, K. R.

    1983-01-01

    A sample of mature lunar fines (10084.151) was solubilized to a high degree (about 17 percent) by the chelating agent salicylic acid (0.01. M). The neutralized (pH adjusted to 7.0) leachate was found to inhibit the growth of Escherichia coli (ATCC 259922) in a minimial mineral salts glucose medium; however, the inhibition was somewhat less than that caused by neutralized salicylic acid alone. The presence of lunar fines in the minimal medium was highly stimulatory to growth of E. coli following an early inhibitory response. The bacterium survived less well in the lunar leachate than in distilled water, no doubt because of the salicylate. It was concluded that the sample of lunar soil tested has nutritional value to E. coli and that certain products of fermentation helped to solubilize the lunar soil.

  12. Customizing digital printing for fine art practice

    Science.gov (United States)

    Parraman, Carinna E.; Thirkell, Paul; Hoskins, Steve; Wang, Hong Qiang; Laidler, Paul

    2005-01-01

    The presentation will demonstrate how through alternative methods of digital print production the Centre for Fine Print Research (CFPR) is developing methodologies for digital printing that attempt to move beyond standard reproductive print methods. Profiling is used for input and output hardware, along with bespoke profiling for fine art printmaking papers. Examples of artist's work, and examples from the Perpetual Portfolio are included - an artist in residence scheme for selected artists wanting to work at the Centre and to make a large-format digital print. Colour is an important issue: colour fidelity, colour density on paper, colour that can be achieved through multiple-pass printing. Research is also underway to test colour shortfalls in the current inkjet ink range, and to extend colour through the use of traditional printing inks.

  13. Solid State Physics Principles and Modern Applications

    CERN Document Server

    Quinn, John J

    2009-01-01

    Intended for a two semester advanced undergraduate or graduate course in Solid State Physics, this treatment offers modern coverage of the theory and related experiments, including the group theoretical approach to band structures, Moessbauer recoil free fraction, semi-classical electron theory, magnetoconductivity, electron self-energy and Landau theory of Fermi liquid, and both quantum and fractional quantum Hall effects. Integrated throughout are developments from the newest semiconductor devices, e.g. space charge layers, quantum wells and superlattices. The first half includes all material usually covered in the introductory course, but in greater depth than most introductory textbooks. The second half includes most of the important developments in solid-state researches of the past half century, addressing e.g. optical and electronic properties such as collective bulk and surface modes and spectral function of a quasiparticle, which is a basic concept for understanding LEED intensities, X ray fine struc...

  14. Drop Impact on a Solid Surface

    KAUST Repository

    Josserand, C.

    2015-09-22

    © Copyright 2016 by Annual Reviews. All rights reserved. A drop hitting a solid surface can deposit, bounce, or splash. Splashing arises from the breakup of a fine liquid sheet that is ejected radially along the substrate. Bouncing and deposition depend crucially on the wetting properties of the substrate. In this review, we focus on recent experimental and theoretical studies, which aim at unraveling the underlying physics, characterized by the delicate interplay of not only liquid inertia, viscosity, and surface tension, but also the surrounding gas. The gas cushions the initial contact; it is entrapped in a central microbubble on the substrate; and it promotes the so-called corona splash, by lifting the lamella away from the solid. Particular attention is paid to the influence of surface roughness, natural or engineered to enhance repellency, relevant in many applications.

  15. Solid State Division

    Energy Technology Data Exchange (ETDEWEB)

    Green, P.H.; Watson, D.M. (eds.)

    1989-08-01

    This report contains brief discussions on work done in the Solid State Division of Oak Ridge National Laboratory. The topics covered are: Theoretical Solid State Physics; Neutron scattering; Physical properties of materials; The synthesis and characterization of materials; Ion beam and laser processing; and Structure of solids and surfaces. (LSP)

  16. Fractal aggregation and breakup of fine particles

    Directory of Open Access Journals (Sweden)

    Li Bingru

    2016-01-01

    Full Text Available Breakup may exert a controlling influence on particle size distributions and particles either are fractured or are eroded particle-by-particle through shear. The shear-induced breakage of fine particles in turbulent conditions is investigated using Taylor-expansion moment method. Their equations have been derived in continuous form in terms of the number density function with particle volume. It suitable for future implementation in computational fluid dynamics modeling.

  17. Process for treating moisture laden coal fines

    Science.gov (United States)

    Davis, Burl E.; Henry, Raymond M.; Trivett, Gordon S.; Albaugh, Edgar W.

    1993-01-01

    A process is provided for making a free flowing granular product from moisture laden caked coal fines, such as wet cake, by mixing a water immiscible substance, such as oil, with the caked coal, preferably under low shear forces for a period of time sufficient to produce a plurality of free flowing granules. Each granule is preferably comprised of a dry appearing admixture of one or more coal particle, 2-50% by weight water and the water immiscible substance.

  18. Alternate Methods for Disposal of Nitrocellulose Fines

    Science.gov (United States)

    1985-07-22

    edition$ are obsolete. UNLSSFE UNCLASSIFIED SECURITY CLASSIPICATION OP THIS PAGE recycled; and, being ubituitous in nature , are not considered...Matrix xomparison of technologies ................. 22 3.4 Ranking and seleccion of technologies ............. 26 4. CONCLUSIONS AND RECOMMENDATIONS 4.1...ubiquitous in nature , are not considered pollutants anyway. There are several "ready technologies" that appear to be capable of removing NC fines more

  19. On a time varying fine structure constant

    CERN Document Server

    Berman, M S; Berman, Marcelo S.; Trevisan, Luis A.

    2001-01-01

    By employing Dirac LNH, and a further generalization by Berman (GLNH), we estimate how should vary the total number of nucleons, the energy density, Newton Gravitational constant, the cosmological constant, the magnetic permeability and electric permitivity, of the Universe,in order to account for the experimentally observed time variation of the fine structure constant. As a bonus,we find an acceptable value for the deceleration parameter of the present Universe, compatible with the Supernovae observations.

  20. Corrosion of surface defects in fine wires.

    Science.gov (United States)

    Rentler, R M; Greene, N D

    1975-11-01

    Defects were observed on the surfaces of various fine diameter wires commonly used in biomedical applications. These surface irregularities were viewed at high magnifications using a scanning electron microscope which has a much greater depth of field than normal light microscopy. Defects include scratches, pits, and crevices, which are the result of commercial wire drawing practices. Corrosion test results show that imperfections can serve as sites for localized corrosion attack which could lead to premature failures.

  1. Mutagenic potential of fine wastes from dimension stone industry.

    Science.gov (United States)

    Aguiar, Luara Louzada; Tonon, Camila Bruschi; Nunes, Erika Takagi; Braga, Adriane Cristina Araújo; Neves, Mirna Aparecida; de Oliveira David, José Augusto

    2016-03-01

    The industrial treatment of dimension stones, such as marbles and granites, includes a stage of plate polishing, in which resins and abrasives are used, producing a fine grained waste with high moisture content. These wastes pass through decantation tanks in order to separate the solid and liquid phases. Until now, there is no knowledge about the mutagenic effects that this effluent can cause to organisms exposed to it. Thus, this study evaluated the mutagenic potential of dimension stone polishing wastes in onion root cells and fish erythrocytes. The onion seeds were germinated in Petri dishes with filter paper moistened in the liquid phase of the effluent. After germination, the onion roots were prepared for analysis of chromosomal aberrations in meristematic cells. The fishes were exposed during 72h to the solid phase of the effluent diluted in pure groundwater. Blood samples were used for counting of micronucleus and nuclear abnormalities. The onion seeds had similar germination and mitotic index in all treatments. However, it was observed in the seeds exposed to the polishing waste, numbers significantly higher of micronucleus, nuclear buds and other chromosomal aberrations when compared with the negative control. The fishes exposed to the waste showed numbers significantly higher of micronucleus when compared with the negative control. The fishes from all treatments showed significant increase in nuclear abnormalities when compared to the negative control. We concluded that the analysed wastes have mutagenic potential at the studied conditions; this effect can be related to the high content of phenolic compounds identified in the samples.

  2. ELECTROSTATICALLY SUPPORTED MIXING OF FINE GRAINED PARTICLES

    Institute of Scientific and Technical Information of China (English)

    K.-E.; Wirth; M.; Linsenbühler

    2005-01-01

    The processing of fine-grained particles with diameters between 1 and 10 microns is difficult due to strong van-der-Waals attraction forces. In order to improve the handling properties, the fine-grained particles, i.e. host-particles,are coated with various nanoparticles, i.e. guest-particles. The mixing of fine-grained powders is influenced by particle-particle interactions. If these forces are distinctively used, both interactive and ordered mixtures can be produced.These particle mixtures consist of composite-particles that have new physical properties. These modified properties d epend strongly on the coating process, the diameter- and mass-relationship of the guest- and the host-particles. The properties of the composite-particles can systematically be adjusted to the requirements of industrial applications. For example, a laboratory bubbling fluidized bed can be used to describe the conveying behavior of the functionalized host-particles. Applications for the functionalized particles are in the pharmaceutical and the powder coating industries,e.g. enhanced dry powder inhalers and thin lacquer films. The present research compares three different mixing/coating processes. The composite-particles are characterized by TEM, SEM and with their fluidization characteristics. The coating process itself is monitored by the electrostatic charge of the particles.

  3. Variation of the fine structure constant

    CERN Document Server

    Lipovka, Anton A

    2016-01-01

    In present paper we evaluate the fine structure constant variation which should take place as the Universe is expanded and its curvature is changed adiabatically. This changing of the fine structure constant is attributed to the energy lost by physical system (consist of baryonic component and electromagnetic field) due to expansion of our Universe. Obtained ratio (d alpha)/alpha = 1. 10{-18} (per second) is only five times smaller than actually reported experimental limit on this value. For this reason this variation can probably be measured within a couple of years. To argue the correctness of our approach we calculate the Planck constant as adiabatic invariant of electromagnetic field, from geometry of our Universe in the framework of the pseudo- Riemannian geometry. Finally we discuss the double clock experiment based on Al+ and Hg+ clocks carried out by T. Rosenband et al. (Science 2008). We show that in this particular case there is an error in method and this way the fine structure constant variation c...

  4. Defending The Fallacy of Fine-Tuning

    CERN Document Server

    Stenger, Victor J

    2012-01-01

    In 2011, I published a popular-level book, The Fallacy of Fine-Tuning: Why the Universe is Not Designed for Us. It investigated a common claim found in contemporary religious literature that the parameters of physics and cosmology are so delicately balanced, so "fine-tuned," that any slight change and life in the universe would have been impossible. I concluded that while the precise form of life we find on Earth would not exist with slight changes in these parameters, some form of life could have evolved over a parameter range that is not infinitesimal, as often claimed. Postdoctoral fellow Luke Barnes has written a lengthy, highly technical review [arXiv:1112.4647] of the scientific literature on the fine-tuning problem. I have no significant disagreement with that literature and no prominent physicist or cosmologist has disputed my basic conclusions. Barnes does not invalidate these conclusions and misunderstands and misrepresents much of what is in the book.

  5. Comparison of polymer applications to treatment of oil sands fine tailings

    Energy Technology Data Exchange (ETDEWEB)

    Li, H.; Zhou, J.; Chow, R. [Alberta Research Council, Edmonton, AB (Canada)

    2008-07-01

    Oil sands tailings are disposed of into large ponds where the coarse particles settle out, and fine particles settle down very slowly to form a stable suspension called mature fine tailings (MFTs). Many oil sands projects are not meeting tailings management targets. Polymer applications are being designed to create agglomerated particles. This presentation discussed a study that compared 3 types of polymers in solids dewatering processes: (1) polyacrylamide (PAM); a aluminum PAM hybrid (Al-PAM) and a thermal-sensitive poly(N-isopropyl acrylamide (PNIPAM). The aim of the study was to determine the optimal polymeric facilitation. Oil sands tailings from lab flotation tests were used. The effect on the initial settling rate of the tailings using the polymers was studied. Inter-particle forces were also compared, as well as the effects of temperature on polymer transitions in aqueous solutions. The effects of the polymers on silica settling and consolidation were examined. Dewatering performance was also compared. Multi-function polymers (MFP) were used to enhance water recovery from settling, consolidation and filtration. Synergetic-effect polymers (SEP) were used to enhance bitumen and water recovery. Results of the study showed that PAM effectively induced solids flocculation, but flocculants were irregular in shape. Al-PAM induced stronger flocculation of particles with dense spherical flocculants. PNIPAM enhanced dewatering in both settling and consolidation. It was concluded that PNIPAM manipulated inter-particle forces with the help of external stimuli conditions to obtain solids sediment with less volume. tabs., figs.

  6. NUMERICAL SIMULATION OF FINE PARTICLE SEPARATION IN A ROTATIONAL TUBE SEPARATOR

    Institute of Scientific and Technical Information of China (English)

    Jinyu Jiao; Ying Zheng; Guogang Sun

    2005-01-01

    This paper presents a numerical analysis of gas-solid separation in a rotational tube separator. This separator which collects fine particles from gas in laminar flow is effective for fine particle separation. The separation efficiency and critical particle diameter of the separator were simulated using CFD package (FLUENT 6.0). The simulation showed that separation efficiency can be significantly decreased due to the presence of turbulence. The simulation also showed that the Saffman lift force has little effect on the efficiency of this separator. The critical particle diameter of this tube separator was also calculated theoretically. Some experimental data were provided to validate the simulation results. Comparison between experimental results and simulation predictions on separation efficiency showed satisfactory agreement.

  7. RSW Fully Tet Cell-Centered Fine Mesh

    Data.gov (United States)

    National Aeronautics and Space Administration — This is the RSW dataset for a fine fully tetrahedral grid designed for a cell-centered unstructured solver. UG3 : Grid File Name = rsw_fine_tetcc.b8.ugrid UG3 : Quad...

  8. Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid

    Science.gov (United States)

    ... News Physician Resources Professions Site Index A-Z Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid ... Needle Aspiration Biopsy of the Thyroid? What is Ultrasound-Guided Fine Needle Aspiration Biopsy of the Thyroid? ...

  9. INVESTIGATIONS INTO BIOFOULING PHENOMENA IN FINE PORE AERATION DEVICES

    Science.gov (United States)

    Microbiologically-based procedures were used to describe biofouling phenomena on fine pore aeration devices and to determine whether biofilm characteristics could be related to diffuser process performance parameters. Fine pore diffusers were obtained from five municipal wastewa...

  10. Identifying fine sediment sources to alleviate flood risk caused by fine sediments through catchment connectivity analysis

    Science.gov (United States)

    Twohig, Sarah; Pattison, Ian; Sander, Graham

    2017-04-01

    Fine sediment poses a significant threat to UK river systems in terms of vegetation, aquatic habitats and morphology. Deposition of fine sediment onto the river bed reduces channel capacity resulting in decreased volume to contain high flow events. Once the in channel problem has been identified managers are under pressure to sustainably mitigate flood risk. With climate change and land use adaptations increasing future pressures on river catchments it is important to consider the connectivity of fine sediment throughout the river catchment and its influence on channel capacity, particularly in systems experiencing long term aggradation. Fine sediment erosion is a continuing concern in the River Eye, Leicestershire. The predominately rural catchment has a history of flooding within the town of Melton Mowbray. Fine sediment from agricultural fields has been identified as a major contributor of sediment delivery into the channel. Current mitigation measures are not sustainable or successful in preventing the continuum of sediment throughout the catchment. Identifying the potential sources and connections of fine sediment would provide insight into targeted catchment management. 'Sensitive Catchment Integrated Modelling Analysis Platforms' (SCIMAP) is a tool often used by UK catchment managers to identify potential sources and routes of sediment within a catchment. SCIMAP is a risk based model that combines hydrological (rainfall) and geomorphic controls (slope, land cover) to identify the risk of fine sediment being transported from source into the channel. A desktop version of SCIMAP was run for the River Eye at a catchment scale using 5m terrain, rainfall and land cover data. A series of SCIMAP model runs were conducted changing individual parameters to determine the sensitivity of the model. Climate Change prediction data for the catchment was used to identify potential areas of future connectivity and erosion risk for catchment managers. The results have been

  11. Solid expellant plasma generator

    Science.gov (United States)

    Stone, Nobie H. (Inventor); Poe, Garrett D. (Inventor); Rood, Robert (Inventor)

    2010-01-01

    An improved solid expellant plasma generator has been developed. The plasma generator includes a support housing, an electrode rod located in the central portion of the housing, and a mass of solid expellant material that surrounds the electrode rod within the support housing. The electrode rod and the solid expellant material are made of separate materials that are selected so that the electrode and the solid expellant material decompose at the same rate when the plasma generator is ignited. This maintains a point of discharge of the plasma at the interface between the electrode and the solid expellant material.

  12. Solid state phenomena

    CERN Document Server

    Lawrance, R

    1972-01-01

    Solid State Phenomena explores the fundamentals of the structure and their influence on the properties of solids. This book is composed of five chapters that focus on the electrical and thermal conductivities of crystalline solids. Chapter 1 describes the nature of solids, particularly metals and crystalline materials. This chapter also presents a model to evaluate crystal structure, the forces between atom pairs, and the mechanism of plastic and elastic deformation. Chapter 2 demonstrates random vibrations of atoms in a solid using a one-dimensional array, while Chapter 3 examines the resista

  13. CHARACTERIZATION OF SOLID CONES

    Institute of Scientific and Technical Information of China (English)

    Qiu Jinghui

    2008-01-01

    The author gives a dual characterization of solid cones in locally convex spaces.From this the author obtains some criteria for judging convex cones to be solid in various inds of locally convex spaces. Using a general expression of the interior of a solid cone,the author obtains a number of necessary and sufficient conditions for convex cones to be solid in the framework of Banach spaces. In particular, the author gives a dual relationship between solid cones and generalized sharp cones. The related known results are improved and extended.

  14. Fine particle emissions from residential wood combustion

    Energy Technology Data Exchange (ETDEWEB)

    Tissari, J.

    2008-07-01

    Residential wood combustion (RWC) appliances have the high probability of incomplete combustion, producing e.g. fine particles and hazardous organic compounds. In this thesis, the fine particle number and mass emissions, particle composition and morphology, and gas emissions were investigated from the modern (MMH) and conventional masonry heaters (CMH), sauna stoves (SS) and pellet burner. The investigation was based on laboratory and field experiments applying extensive and unique particle sampling methods. The appliance type, fuel and operational practices were found to affect clearly the fine particle emissions. In good combustion conditions (e.g. in pellet combustion), the fine particle mass (PM{sub 1}) emission factors were low, typically below 0.3 g kg-1, and over 90% of the PM{sub 1} consisted of inorganic compounds (i.e fine ash). From the CMH the typical PM{sub 1} values were 1.6-1.8 g kg-1, and from the SS 2.7-5.0 g kg-1, but were strongly dependent on operational practices. The smouldering combustion in CMH increased PM{sub 1} emission up to 10 g kg-1. The good secondary combustion in the MMH reduced the particle organic matter (POM) and gaseous emissions, but not substantially the elemental carbon (EC, i.e. soot) emission, and the typical PM{sub 1} values were 0.7-0.8 g kg-1. The particle number emissions were high, and did not correspond with the completition of combustion. The particle number distributions were mainly dominated by ultrafine (<100 nm) particles, but varied dependent on combustion conditions. The electronmicroscopy analyses showed that ultrafine particles were composed mainly of K, S and Zn. From the smouldering combustion, particles were composed mainly of carbon compounds and they had a closed sinteredlike structure, due to organic matter on the particles. Controlling the gasification rate via the primary air supply, log and batch size, as well as fuel moisture content, is important for the reduction of emissions in batch combustion

  15. Influence of fine sediment on the fluidity of debris flows

    OpenAIRE

    HOTTA, Norifumi; Kaneko, Takahiro; Iwata, Tomoyuki; Nishimoto, Haruo

    2013-01-01

    Debris flows include a great diversity of grain sizes with inherent features such as inverse grading, particle size segregation, and liquefaction of fine sediment. The liquefaction of fine sediment affects the fluidity of debris flows, although the behavior and influence of fine sediment in debris flows have not been examined sufficiently. This study used flume tests to detect the effect of fine sediment on the fluidity of laboratory debris flows consisting of particles with various diameters...

  16. Solids fluidizer-injector

    Science.gov (United States)

    Bulicz, T.R.

    1990-04-17

    An apparatus and process are described for fluidizing solid particles by causing rotary motion of the solid particles in a fluidizing chamber by a plurality of rotating projections extending from a rotatable cylinder end wall interacting with a plurality of fixed projections extending from an opposite fixed end wall and passing the solid particles through a radial feed orifice open to the solids fluidizing chamber on one side and a solid particle utilization device on the other side. The apparatus and process are particularly suited for obtaining intermittent feeding with continual solids supply to the fluidizing chamber. The apparatus and process are suitable for injecting solid particles, such as coal, to an internal combustion engine. 3 figs.

  17. Solid Base Catalysis

    CERN Document Server

    Ono, Yoshio

    2011-01-01

    The importance of solid base catalysts has come to be recognized for their environmentally benign qualities, and much significant progress has been made over the past two decades in catalytic materials and solid base-catalyzed reactions. The book is focused on the solid base. Because of the advantages over liquid bases, the use of solid base catalysts in organic synthesis is expanding. Solid bases are easier to dispose than liquid bases, separation and recovery of products, catalysts and solvents are less difficult, and they are non-corrosive. Furthermore, base-catalyzed reactions can be performed without using solvents and even in the gas phase, opening up more possibilities for discovering novel reaction systems. Using numerous examples, the present volume describes the remarkable role solid base catalysis can play, given the ever increasing worldwide importance of "green" chemistry. The reader will obtain an overall view of solid base catalysis and gain insight into the versatility of the reactions to whic...

  18. The theory of granular packings for fine soils

    Science.gov (United States)

    Yanqui, Calixtro

    2017-06-01

    Fine soils are substances made of tiny particles, for which, besides their geometrical assemblage, the electrochemical forces are important. But the broad experience in Soil Mechanics has shown that, excluding the time, they behave like granular materials. By using the scanning electron microscopy, it has been shown by several authors that clay assemblages are structures of the second order, made of solid particles grouped in clusters. Applying the theory of packings of spheres in contact to the intra-cluster structure as well as to the entire mass of soil, a fundamental equation is obtained. The plastic limit is found to be a constant for a geological formation, because it is obtained by eliminating the capillary water and transforming the clay mass into a first order structure. The liquid limit is a inherently property of the second order, due to the development of clusters. Consequently, there is a linear relationship between the plasticity index and the liquid limit, with a slope of unity, as can be deduced from the abundant data reported by several authors around the world.

  19. The theory of granular packings for fine soils

    Directory of Open Access Journals (Sweden)

    Yanqui Calixtro

    2017-01-01

    Full Text Available Fine soils are substances made of tiny particles, for which, besides their geometrical assemblage, the electrochemical forces are important. But the broad experience in Soil Mechanics has shown that, excluding the time, they behave like granular materials. By using the scanning electron microscopy, it has been shown by several authors that clay assemblages are structures of the second order, made of solid particles grouped in clusters. Applying the theory of packings of spheres in contact to the intra-cluster structure as well as to the entire mass of soil, a fundamental equation is obtained. The plastic limit is found to be a constant for a geological formation, because it is obtained by eliminating the capillary water and transforming the clay mass into a first order structure. The liquid limit is a inherently property of the second order, due to the development of clusters. Consequently, there is a linear relationship between the plasticity index and the liquid limit, with a slope of unity, as can be deduced from the abundant data reported by several authors around the world.

  20. Toward improving fine needle aspiration cytology by applying Raman microspectroscopy

    Science.gov (United States)

    Becker-Putsche, Melanie; Bocklitz, Thomas; Clement, Joachim; Rösch, Petra; Popp, Jürgen

    2013-04-01

    Medical diagnosis of biopsies performed by fine needle aspiration has to be very reliable. Therefore, pathologists/cytologists need additional biochemical information on single cancer cells for an accurate diagnosis. Accordingly, we applied three different classification models for discriminating various features of six breast cancer cell lines by analyzing Raman microspectroscopic data. The statistical evaluations are implemented by linear discriminant analysis (LDA) and support vector machines (SVM). For the first model, a total of 61,580 Raman spectra from 110 single cells are discriminated at the cell-line level with an accuracy of 99.52% using an SVM. The LDA classification based on Raman data achieved an accuracy of 94.04% by discriminating cell lines by their origin (solid tumor versus pleural effusion). In the third model, Raman cell spectra are classified by their cancer subtypes. LDA results show an accuracy of 97.45% and specificities of 97.78%, 99.11%, and 98.97% for the subtypes basal-like, HER2+/ER-, and luminal, respectively. These subtypes are confirmed by gene expression patterns, which are important prognostic features in diagnosis. This work shows the applicability of Raman spectroscopy and statistical data handling in analyzing cancer-relevant biochemical information for advanced medical diagnosis on the single-cell level.

  1. Impact of ozonation on particle aggregation in mature fine tailings.

    Science.gov (United States)

    Liang, Jiaming; Tumpa, Fahmida; Pérez Estrada, Leonidas; Gamal El-Din, Mohamed; Liu, Yang

    2014-12-15

    The extraction of bitumen from the oil sands in Canada generates tonnes of mature fine tailings (MFT), consisting of a mineral matrix of sand, clay, and water, which without treatment requires thousands of years to fully consolidate. We assessed the performance of a novel ozonation method designed to enhance the settling of MFT and explored the mechanisms involved. The solid content of MFT obtained from oil sands tailings was adjusted to 1, 3, 5 wt % with water before applying 15, 30, and 60 min of ozonation. MFT settled after a short (15 min) ozonation treatment, resulting in a sample with clear released water on the top and condensed sludge at the bottom. The water chemistry characteristics, particles' surface charge and chemical bonding were measured. Ozonation led to the increased organic acids concentrations in MFT suspension through converting of organic matter from high to low molecular weight, and detaching organic coating on MFT particles. The pH and the concentrations of ions in the MFT suspension were changed significantly, an association of metal ions with MFT particles was promoted, and the surface charges of MFT particles were neutralized. Consequently, the MFT suspension was destabilized and MFT particle precipitation was observed.

  2. Development of fine motor skills in preterm infants

    NARCIS (Netherlands)

    Bos, Arend F.; Van Braeckel, Koenraad N. J. A.; Hitzert, Marrit M.; Tanis, Jozien C.; Roze, Elise

    2013-01-01

    Fine motor skills are related to functioning in daily life and at school. We reviewed the status of knowledge, in preterm children, on the development of fine motor skills, the relation with gross motor skills, and risk factors for impaired fine motor skills. We searched the past 15 years in PubMed,

  3. Extended X-ray absorption fine structure investigation of nitrogen stabilized expanded austenite

    DEFF Research Database (Denmark)

    Oddershede, Jette; Christiansen, Thomas; Ståhl, Kenny

    2010-01-01

    As-delivered austenitic stainless steel and nitrogen stabilized expanded austenite, both fully nitrided and denitrided (in H2), were investigated with Cr, Fe and Ni extended X-ray absorption fine structure. The data shows pronounced short-range ordering of Cr and N. For the denitrided specimen...... the N atoms remaining in the solid state after H2-reduction are trapped by Cr atoms. Quantitative interpretation in terms of the local distortions around Cr atoms and their N coordination number reveals that no Cr–N clusters or CrN platelets are present....

  4. Hydrophobic Dewatering of Fine Coal. Topical report, March 1, 1995-March 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, R.; Sohn, S.; Luttrell, J.; Phillips, D.

    1997-12-31

    Many advanced fine coal cleaning technologies have been developed in recent years under the auspices of the U.S. Department of Energy. However, they are not as widely deployed in industry as originally anticipated. An important reason for this problem is that the cleaned coal product is difficult to dewater because of the large surface area associated with fine particles. Typically, mechanical dewatering, such as vacuum filtration and centrifugation, can reduce the moisture to 20-35% level, while thermal drying is costly. To address this important industrial problem, Virginia Tech has developed a novel dewatering process, in which water is displaced from the surface of fine particulate materials by liquid butane. Since the process is driven by the hydrophobic interaction between coal and liquid butane, it was referred to as hydrophobic dewatering (HD). A fine coal sample with 21.4 pm median size was subjected to a series of bench-scale HD tests. It was a mid-vol bituminous coal obtained from the Microcel flotation columns operating at the Middle Fork coal preparation plant, Virginia. All of the test results showed that the HD process can reduce the moisture to substantially less than 10%. The process is sensitive to the amount of liquid butane used in the process relative to the solids concentration in the feed stream. Neither the intensity nor the time of agitation is critical for the process. Also, the process does not require long time for phase separation. Under optimal operating conditions, the moisture of the fine coal can be reduced to 1% by weight of coal.

  5. Coal-sand attrition system and its importance in fine coal cleaning. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, R.K.; Zhu, Qinsheng

    1993-08-01

    It is known that ultra-fine coals are prerequisite for the deep cleaning of most US coal seams if environmental pollution arising from the use of such coals is to be minimized. Therefore, the production of finely liberated coal particles in conjunction with reduced heavy metal contaminants at low costs is desirable, if not mandatory. The liberation of intimately disseminated impurities from the coal matrix therefore, demands that the material be ground to a high degree of fineness. Similarily, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as severe product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality. The use of natural quartz sand as grinding media in the comminution of industrial minerals in stirred ball mills has been indicated. The advantages of natural sand compared to steel media include low specific energy inputs, elimination of heavy metal contaminants and low media costs. In this work, the effect of rotor speed, solids concentration and feed-size are studied on four coals in conjunction with silica sand and steel shot. The results obtained are used to evaluate the suitability of silica sands as an alternative grinding media. for coal. Coal-sand and coal-steel systems are compared in terms of specific energy consumption, product fineness, media/wear contaminationanalysis and calorific values, liberation spectrum and particle shape characteristics. In general cleaner flotation concentrate was obtained from coals when they were ground with sand media. The zeta potential of coals was found to be different and lower when they ground with sand.

  6. Development of a semi-solid metal processing technique for aluminium casting applications

    OpenAIRE

    Sangop Thanabumrungkul; Jessada Wannasin

    2008-01-01

    A semi-solid metal processing technique has been invented and is being developed for aluminium casting applications in Thailand. The technique uses fine gas bubbles to create convection necessary for modifying grain structure. Semi-solid metal processing of three aluminium alloys, A356, Al-4.4%Cu, and ADC12, was investigated. Results show that the novel technique successfully modified A356 and Al-4.4%Cu to become semi-solid slurry with solid fractions up to about 50%. Current developments sho...

  7. Fine structure of synapses on dendritic spines

    Directory of Open Access Journals (Sweden)

    Michael eFrotscher

    2014-09-01

    Full Text Available Camillo Golgi’s Reazione Nera led to the discovery of dendritic spines, small appendages originating from dendritic shafts. With the advent of electron microscopy (EM they were identified as sites of synaptic contact. Later it was found that changes in synaptic strength were associated with changes in the shape of dendritic spines. While live-cell imaging was advantageous in monitoring the time course of such changes in spine structure, EM is still the best method for the simultaneous visualization of all cellular components, including actual synaptic contacts, at high resolution. Immunogold labeling for EM reveals the precise localization of molecules in relation to synaptic structures. Previous EM studies of spines and synapses were performed in tissue subjected to aldehyde fixation and dehydration in ethanol, which is associated with protein denaturation and tissue shrinkage. It has remained an issue to what extent fine structural details are preserved when subjecting the tissue to these procedures. In the present review, we report recent studies on the fine structure of spines and synapses using high-pressure freezing (HPF, which avoids protein denaturation by aldehydes and results in an excellent preservation of ultrastructural detail. In these studies, HPF was used to monitor subtle fine-structural changes in spine shape associated with chemically induced long-term potentiation (cLTP at identified hippocampal mossy fiber synapses. Changes in spine shape result from reorganization of the actin cytoskeleton. We report that cLTP was associated with decreased immunogold labeling for phosphorylated cofilin (p-cofilin, an actin-depolymerizing protein. Phosphorylation of cofilin renders it unable to depolymerize F-actin, which stabilizes the actin cytoskeleton. Decreased levels of p-cofilin, in turn, suggest increased actin turnover, possibly underlying the changes in spine shape associated with cLTP. The findings reviewed here establish HPF as

  8. Increasing the sludge energy potential of wastewater treatment plants by introducing fine mesh sieves for primary treatment.

    Science.gov (United States)

    Paulsrud, Bjarne; Rusten, Bjørn; Aas, Bjørn

    2014-01-01

    The objective of this study was to compare some basic characteristics of sludge from fine mesh sieves (sieve sludge) with sludge from primary clarifiers (primary sludge) regarding their energy potential with a focus on anaerobic digestion and/or incineration. Nineteen samples of sludge from fine mesh sieve plants (most of them without fine screens and grit chambers as pre-treatment) and 10 samples of primary sludge were analysed for the content of dry solids (DS), volatile solids (VS), chemical oxygen demand (COD), calorific value and methane potential. The results demonstrated that the sieve sludges have significantly higher VS content and higher methane potential than primary sludges, clearly indicating an increased sludge energy potential if fine mesh sieves are used for primary treatment instead of primary clarifiers at wastewater treatment plants with anaerobic digesters. If the sludges from primary treatment are to be incinerated or used as fuel in cement kilns, there is no significant difference in energy potential (given as calorific values) for the two types of primary treatment.

  9. Dark energy with fine redshift sampling

    Science.gov (United States)

    Linder, Eric V.

    2007-03-01

    The cosmological constant and many other possible origins for acceleration of the cosmic expansion possess variations in the dark energy properties slow on the Hubble time scale. Given that models with more rapid variation, or even phase transitions, are possible though, we examine the fineness in redshift with which cosmological probes can realistically be employed, and what constraints this could impose on dark energy behavior. In particular, we discuss various aspects of baryon acoustic oscillations, and their use to measure the Hubble parameter H(z). We find that currently considered cosmological probes have an innate resolution no finer than Δz≈0.2 0.3.

  10. Leeuwpan fine coal dense medium plant

    CSIR Research Space (South Africa)

    Lundt, M

    2010-11-01

    Full Text Available availability to treat the higher grade coal (the bottom layer of coal) from the no. 2 Seam for a local and export metallurgical market. Following the path of evolution, in 2007, Leeuwpan commissioned the first double stage ultra-fines dense medium cyclone... plant in the coal industry, to form part of its overall DMS plant. It replaced the spirals to treat the -1 mm material. Spirals are still the most commonly and accepted method used by the industry, but it seems as if the pioneering cyclone process...

  11. Fine Structure Constant: Theme With Variations

    CERN Document Server

    Bezerra, V B; Muniz, C R; Tahim, M O; Vieira, H S

    2016-01-01

    In this paper, we study the spatial variation of the fine structure constant $\\alpha$ due to the presence of a static and spherically symmetric gravitational source. The procedure consists of calculating the solution including the energy eigenvalues of a massive scalar field around that source, considering the weak-field regimen, which yields the gravitational analog of the atomic Bohr levels. From this result, we obtain several values for the effective $\\alpha$ by considering some scenarios of semi-classical and quantum gravities. Constraints on the parameters of the involved theories are calculated from astrophysical observations of the white dwarf emission spectra. Such constraints are compared with those ones obtained in the literature.

  12. Dewatering studies of fine clean coal

    Energy Technology Data Exchange (ETDEWEB)

    Parekh, B.K.

    1991-01-01

    The main objective of the present research program is to study and understand dewatering characteristics of ultrafine clean coal obtained using the advanced column flotation technique from the Kerr-McGee's Galatia preparation plant fine coal waste stream. It is also the objective of the research program to utilize the basic study results, i.e., surface chemical, particle shape particle size distribution, etc., in developing a cost-effective dewatering method. The ultimate objective is to develop process criteria to obtain a dewatered clean coal product containing less that 20 percent moisture, using the conventional vacuum dewatering equipment. (VC)

  13. Planck scale operators, inflation and fine tuning

    CERN Document Server

    Marunovic, Anja

    2016-01-01

    Ultraviolet completion of the standard model plus gravity at and beyond the Planck scale is a daunting problem to which no generally accepted solution exists. Principal obstacles include (a) lack of data at the Planck scale (b) nonrenormalizability of gravity and (c) unitarity problem. Here we make a simple observation that, if one treats all Planck scale operators of equal canonical dimension democratically, one can tame some of the undesirable features of these models. With a reasonable amount of fine tuning one can satisfy slow roll conditions required in viable inflationary models. That remains true even when the number of such operators becomes very large.

  14. A cyclic universe approach to fine tuning

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, Stephon, E-mail: stephon.alexander@dartmouth.edu [Department of Physics and Astronomy, Dartmouth College, Hanover, NH 03755 (United States); Department of Physics, Brown University, Providence, RI 02906 (United States); Cormack, Sam, E-mail: samuel.c.cormack.gr@dartmouth.edu [Department of Physics and Astronomy, Dartmouth College, Hanover, NH 03755 (United States); Gleiser, Marcelo, E-mail: marcelo.gleiser@dartmouth.edu [Department of Physics and Astronomy, Dartmouth College, Hanover, NH 03755 (United States)

    2016-06-10

    We present a closed bouncing universe model where the value of coupling constants is set by the dynamics of a ghost-like dilatonic scalar field. We show that adding a periodic potential for the scalar field leads to a cyclic Friedmann universe where the values of the couplings vary randomly from one cycle to the next. While the shuffling of values for the couplings happens during the bounce, within each cycle their time-dependence remains safely within present observational bounds for physically-motivated values of the model parameters. Our model presents an alternative to solutions of the fine tuning problem based on string landscape scenarios.

  15. The Fine Structure Constant and Habitable Planets

    CERN Document Server

    Sandora, McCullen

    2016-01-01

    We use the existence of habitable planets to impose anthropic requirements on the fine structure constant, $\\alpha$. To this effect, we present two considerations that restrict its value to be very near the one observed. The first, that the end product of stellar fusion is iron and not one of its neighboring elements, restricts $\\alpha^{-1}$ to be $145\\pm 50$. The second, that radiogenic heat in the Earth's interior remains adequately productive for billions of years, restricts it to be $145\\pm9$. A connection with the grand unified theory window is discussed, effectively providing a route to probe ultra-high energy physics with upcoming advances in planetary science.

  16. The fine structure constant and habitable planets

    Science.gov (United States)

    Sandora, McCullen

    2016-08-01

    We use the existence of habitable planets to impose anthropic requirements on the fine structure constant, α. To this effect, we present two considerations that restrict its value to be very near the one observed. The first, that the end product of stellar fusion is iron and not one of its neighboring elements, restricts α-1 to be 145± 50. The second, that radiogenic heat in the Earth's interior remains adequately productive for billions of years, restricts it to be 145±9. A connection with the grand unified theory window is discussed, effectively providing a route to probe ultra-high energy physics with upcoming advances in planetary science.

  17. The fine structure constant and habitable planets

    DEFF Research Database (Denmark)

    Sandora, McCullen

    2016-01-01

    © 2016 IOP Publishing Ltd and Sissa Medialab srl .We use the existence of habitable planets to impose anthropic requirements on the fine structure constant, α. To this effect, we present two considerations that restrict its value to be very near the one observed. The first, that the end product...... of stellar fusion is iron and not one of its neighboring elements, restricts α-1 to be 145± 50. The second, that radiogenic heat in the Earth's interior remains adequately productive for billions of years, restricts it to be 145±9. A connection with the grand unified theory window is discussed, effectively...

  18. Haptic rendering for simulation of fine manipulation

    CERN Document Server

    Wang, Dangxiao; Zhang, Yuru

    2014-01-01

    This book introduces the latest progress in six degrees of freedom (6-DoF) haptic rendering with the focus on a new approach for simulating force/torque feedback in performing tasks that require dexterous manipulation skills. One of the major challenges in 6-DoF haptic rendering is to resolve the conflict between high speed and high fidelity requirements, especially in simulating a tool interacting with both rigid and deformable objects in a narrow space and with fine features. The book presents a configuration-based optimization approach to tackle this challenge. Addressing a key issue in man

  19. Pre - big bang inflation requires fine tuning

    Energy Technology Data Exchange (ETDEWEB)

    Turner, Michael S. [Fermi National Accelerator Laboratory (FNAL), Batavia, IL (United States); Weinberg, Erick J. [Fermi National Accelerator Laboratory (FNAL), Batavia, IL (United States)

    1997-10-01

    The pre-big-bang cosmology inspired by superstring theories has been suggested as an alternative to slow-roll inflation. We analyze, in both the Jordan and Einstein frames, the effect of spatial curvature on this scenario and show that too much curvature --- of either sign --- reduces the duration of the inflationary era to such an extent that the flatness and horizon problems are not solved. Hence, a fine-tuning of initial conditions is required to obtain enough inflation to solve the cosmological problems.

  20. Method for producing dustless graphite spheres from waste graphite fines

    Science.gov (United States)

    Pappano, Peter J [Oak Ridge, TN; Rogers, Michael R [Clinton, TN

    2012-05-08

    A method for producing graphite spheres from graphite fines by charging a quantity of spherical media into a rotatable cylindrical overcoater, charging a quantity of graphite fines into the overcoater thereby forming a first mixture of spherical media and graphite fines, rotating the overcoater at a speed such that the first mixture climbs the wall of the overcoater before rolling back down to the bottom thereby forming a second mixture of spherical media, graphite fines, and graphite spheres, removing the second mixture from the overcoater, sieving the second mixture to separate graphite spheres, charging the first mixture back into the overcoater, charging an additional quantity of graphite fines into the overcoater, adjusting processing parameters like overcoater dimensions, graphite fines charge, overcoater rotation speed, overcoater angle of rotation, and overcoater time of rotation, before repeating the steps until graphite fines are converted to graphite spheres.

  1. Solid state video cameras

    CERN Document Server

    Cristol, Y

    2013-01-01

    Solid State Video Cameras reviews the state of the art in the field of solid-state television cameras as compiled from patent literature. Organized into 10 chapters, the book begins with the basic array types of solid-state imagers and appropriate read-out circuits and methods. Documents relating to improvement of picture quality, such as spurious signal suppression, uniformity correction, or resolution enhancement, are also cited. The last part considerssolid-state color cameras.

  2. Solid propellant rocket motor

    Science.gov (United States)

    Dowler, W. L.; Shafer, J. I.; Behm, J. W.; Strand, L. D. (Inventor)

    1973-01-01

    The characteristics of a solid propellant rocket engine with a controlled rate of thrust buildup to a desired thrust level are discussed. The engine uses a regressive burning controlled flow solid propellant igniter and a progressive burning main solid propellant charge. The igniter is capable of operating in a vacuum and sustains the burning of the propellant below its normal combustion limit until the burning propellant surface and combustion chamber pressure have increased sufficiently to provide a stable chamber pressure.

  3. Understanding solid state physics

    CERN Document Server

    Holgate, Sharon Ann

    2009-01-01

    Where Sharon Ann Holgate has succeeded in this book is in packing it with examples of the application of solid state physics to technology. … All the basic elements of solid state physics are covered … . The range of materials is good, including as it does polymers and glasses as well as crystalline solids. In general, the style makes for easy reading. … Overall this book succeeds in showing the relevance of solid state physics to the modern world … .-Contemporary Physics, Vol. 52, No. 2, 2011I was indeed amused and inspired by the wonderful images throughout the book, carefully selected by th

  4. Molecular Eigensolution Symmetry Analysis and Fine Structure

    Directory of Open Access Journals (Sweden)

    William G. Harter

    2013-01-01

    Full Text Available Spectra of high-symmetry molecules contain fine and superfine level cluster structure related to J-tunneling between hills and valleys on rovibronic energy surfaces (RES. Such graphic visualizations help disentangle multi-level dynamics, selection rules, and state mixing effects including widespread violation of nuclear spin symmetry species. A review of RES analysis compares it to that of potential energy surfaces (PES used in Born-Oppenheimer approximations. Both take advantage of adiabatic coupling in order to visualize Hamiltonian eigensolutions. RES of symmetric and D2 asymmetric top rank-2-tensor Hamiltonians are compared with Oh spherical top rank-4-tensor fine-structure clusters of 6-fold and 8-fold tunneling multiplets. Then extreme 12-fold and 24-fold multiplets are analyzed by RES plots of higher rank tensor Hamiltonians. Such extreme clustering is rare in fundamental bands but prevalent in hot bands, and analysis of its superfine structure requires more efficient labeling and a more powerful group theory. This is introduced using elementary examples involving two groups of order-6 (C6 and D3~C3v, then applied to families of Oh clusters in SF6 spectra and to extreme clusters.

  5. Unitary Evolution and Cosmological Fine-Tuning

    CERN Document Server

    Carroll, Sean M

    2010-01-01

    Inflationary cosmology attempts to provide a natural explanation for the flatness and homogeneity of the observable universe. In the context of reversible (unitary) evolution, this goal is difficult to satisfy, as Liouville's theorem implies that no dynamical process can evolve a large number of initial states into a small number of final states. We use the invariant measure on solutions to Einstein's equation to quantify the problems of cosmological fine-tuning. The most natural interpretation of the measure is the flatness problem does not exist; almost all Robertson-Walker cosmologies are spatially flat. The homogeneity of the early universe, however, does represent a substantial fine-tuning; the horizon problem is real. When perturbations are taken into account, inflation only occurs in a negligibly small fraction of cosmological histories, less than $10^{-6.6\\times 10^7}$. We argue that while inflation does not affect the number of initial conditions that evolve into a late universe like our own, it neve...

  6. Communication Optimizations for Fine-Grained UPCApplications

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wei-Yu; Iancu, Costin; Yelick, Katherine

    2005-07-08

    Global address space languages like UPC exhibit high performance and portability on a broad class of shared and distributed memory parallel architectures. The most scalable applications use bulk memory copies rather than individual reads and writes to the shared space, but finer-grained sharing can be useful for scenarios such as dynamic load balancing, event signaling, and distributed hash tables. In this paper we present three optimization techniques for global address space programs with fine-grained communication: redundancy elimination, use of split-phase communication, and communication coalescing. Parallel UPC programs are analyzed using static single assignment form and a data flow graph, which are extended to handle the various shared and private pointer types that are available in UPC. The optimizations also take advantage of UPC's relaxed memory consistency model, which reduces the need for cross thread analysis. We demonstrate the effectiveness of the analysis and optimizations using several benchmarks, which were chosen to reflect the kinds of fine-grained, communication-intensive phases that exist in some larger applications. The optimizations show speedups of up to 70 percent on three parallel systems, which represent three different types of cluster network technologies.

  7. Suspended solid abatement in a conical fluidized bed flocculator

    Institute of Scientific and Technical Information of China (English)

    Dandan ZHOU; Shuangshi DONG; Keyu LI; Huizhong JIANG; Dandan SHANG

    2013-01-01

    With the random movement of silica gel beads in a conical fluidized bed, micro-vortices resulting from the fluidization promoted the collision and aggregation of suspended fine kaolin powders. The abatement efficiencies of the suspended fine solids under several hydrodynamic conditions were studied, and a suitable control strategy for operating the conical fluidized bed flocculators was identified. The suspended solids abatement efficiency was found to increase with increasing Camp Number and flocculation time (T), but decreased with the increase of velocity gradient (G) within the range studied in this research (165.1-189.6s-1). The abatement efficiencies were all more than 60% at the range of G = 165-180 s 1 and T = 15-33 s at an initial kaolin solid concentration of 150mg·L-1, polymer aluminum chloride dosage of 60 mg· L -1 and sedimentation time of 20 min. However, the formation of flocs was influenced by the liquid back- mixing. Excessive backmixing caused the breakup of ftocs and resulted in difficulty for the fine powders to aggregate and sediment to the reactor bottom. The results of the calculated fractal dimension and measured free sedimenta- tion velocity of flocs obtained at different runs showed similar flocs properties, and indicated an easy control strategy for sedimentation of the flocs.

  8. Fining of glass melts: what we know about fining processes today

    NARCIS (Netherlands)

    Beerkens, R.G.C.

    2009-01-01

    The paper addresses the mechanisms of fining (removal of gases from melt) and the effect of batch composition, oxidation state of the melt and furnace atmosphere on bubble removal processes for commercial glass types, such as float glass and container glass compositions. The mechanisms of the

  9. Fining of glass melts: what we know about fining processes today

    NARCIS (Netherlands)

    Beerkens, R.G.C.

    2009-01-01

    The paper addresses the mechanisms of fining (removal of gases from melt) and the effect of batch composition, oxidation state of the melt and furnace atmosphere on bubble removal processes for commercial glass types, such as float glass and container glass compositions. The mechanisms of the differ

  10. Acclimation of fine root respiration to soil warming involves starch deposition in very fine and fine roots: a case study in Fagus sylvatica saplings.

    Science.gov (United States)

    Di Iorio, Antonino; Giacomuzzi, Valentino; Chiatante, Donato

    2016-03-01

    Root activities in terms of respiration and non-structural carbohydrates (NSC) storage and mobilization have been suggested as major physiological roles in fine root lifespan. As more frequent heat waves and drought periods within the next decades are expected, to what extent does thermal acclimation in fine roots represent a mechanism to cope with such upcoming climatic conditions? In this study, the possible changes in very fine (diameter Fagus sylvatica saplings subjected to a simulated long-lasting heat wave event and to co-occurring soil drying. For both very fine and fine roots, soil temperature (ST) resulted inversely correlated with specific root length, respiration rates and SSs concentration, but directly correlated with root mass, root tissue density and starch concentration. In particular, starch concentration increased under 28 °C for successively decreasing under 21 °C ST. These findings showed that thermal acclimation in very fine and fine roots due to 24 days exposure to high ST (∼ 28 °C), induced starch accumulation. Such 'carbon-savings strategy' should bear the maintenance costs associated to the recovery process in case of restored favorable environmental conditions, such as those occurring at the end of a heat wave event. Drought condition seems to affect the fine root vitality much more under moderate than high temperature condition, making the temporary exposure to high ST less threatening to root vitality than expected.

  11. Dispersal of fine sediment in nearshore coastal waters

    Science.gov (United States)

    Warrick, Jonathan A.

    2013-01-01

    Fine sediment (silt and clay) plays an important role in the physical, ecological, and environmental conditions of coastal systems, yet little is known about the dispersal and fate of fine sediment across coastal margin settings outside of river mouths. Here I provide simple physical scaling and detailed monitoring of a beach nourishment project near Imperial Beach, California, with a high portion of fines (40% silt and clay by weight). These results provide insights into the pathways and residence times of fine sediment transport across a wave-dominated coastal margin. Monitoring of the project used physical, optical, acoustic, and remote sensing techniques to track the fine portion of the nourishment sediment. The initial transport of fine sediment from the beach was influenced strongly by longshore currents of the surf zone that were established in response to the approach angles of the waves. The mean residence time of fine sediment in the surf zone—once it was suspended—was approximately 1 hour, and rapid decreases in surf zone fine sediment concentrations along the beach resulted from mixing and offshore transport in turbid rip heads. For example, during a day with oblique wave directions and surf zone longshore currents of approximately 25 cm/s, the offshore losses of fine sediment in rips resulted in a 95% reduction in alongshore surf zone fine sediment flux within 1 km of the nourishment site. However, because of the direct placement of nourishment sediment on the beach, fine suspended-sediment concentrations in the swash zone remained elevated for several days after nourishment, while fine sediment was winnowed from the beach. Once offshore of the surf zone, fine sediment settled downward in the water column and was observed to transport along and across the inner shelf. Vertically sheared currents influenced the directions and rates of fine sediment transport on the shelf. Sedimentation of fine sediment was greatest on the seafloor directly offshore

  12. Plasma Nanoscience: from Nano-Solids in Plasmas to Nano-Plasmas in Solids

    CERN Document Server

    Ostrikov, K; Meyyappan, M

    2013-01-01

    The unique plasma-specific features and physical phenomena in the organization of nanoscale solid-state systems in a broad range of elemental composition, structure, and dimensionality are critically reviewed. These effects lead to the possibility to localize and control energy and matter at nanoscales and to produce self-organized nano-solids with highly unusual and superior properties. A unifying conceptual framework based on the control of production, transport, and self-organization of precursor species is introduced and a variety of plasma-specific non-equilibrium and kinetics-driven phenomena across the many temporal and spatial scales is explained. When the plasma is localized to micrometer and nanometer dimensions, new emergent phenomena arise. The examples range from semiconducting quantum dots and nanowires, chirality control of single-walled carbon nanotubes, ultra-fine manipulation of graphenes, nano-diamond, and organic matter, to nano-plasma effects and nano-plasmas of different states of matter...

  13. Basic research needs and opportunities at the solid-solid interface - Diffusion

    Science.gov (United States)

    Balluffi, R. W.; Duke, C. B.; Kazmerski, L. L.; Mitchell, K. W.; Reifenberger, R.; Wood, R. F.

    1982-04-01

    The generic problems associated with solar materials solid-solid (S-S) interfaces are reviewed, and goals and techniques for ameliorating the deficiencies are outlined. Photovoltaic, photothermal, and photochemical devices considered are flat plate collectors, thin film Si cells, concentrator systems and compound cells, and polycrystalline systems. Exposure to thermal stresses, electric and radiation fields, chemicals and abrasives during the lifetime of solar cells is expected to create electric, optical, and thermal property changes in the material. Diffusion may also occur in S-S interfacial areas, and determination of the effects on the cells can presently be done using electron microscopy for examining the fine structure, diffraction pattern analysis for the interface structure, and scanning transmission electron microscopy to trace the chemical composition. Additional studies are needed to define the atomic and chemical exchange rates to establish the economic feasibility of low cost cells.

  14. Managing Fine Sediment in Regulated Rivers

    Science.gov (United States)

    Schmidt, J. C.

    2015-12-01

    A paradigm useful in managing dams and diversions is that the combined effects of changing flow regime and sediment supply perturb regulated rivers into sediment deficit or sediment surplus. In the U.S. Southwest, large dams constructed on interregional rivers typically create sediment deficit segments >100 km long. Further downstream, sediment surplus may occur if desert tributaries deliver sufficient amounts of fine sediment, such as parts of the Rio Grande, lower Green River, and Colorado River delta. Sediment surplus also occurs on most smaller regional rivers. The protocols for managing rivers perturbed into sediment deficit have been refined for the Colorado River downstream from Glen Canyon Dam but are nonetheless challenged by externally determined water-supply agreements that require annual water deliveries that sometimes occur when there has been little tributary resupply. Virtually all of the naturally supplied sand to the depleted, 100-km long Marble Canyon comes from the Paria River. The sand delivery rate since 2012 was sufficiently large to trigger short-duration controlled floods under the High Flow Experiment (HFE) Protocol. The sand mass balance of Marble Canyon since 2012 when the HFE Protocol was adopted was positive due to the combination of relatively large sand delivery from the Paria River and average total annual flows. Large total annual flows have the potential to export large amounts of sand and create a negative sand mass balance. Despite the challenge of managing a scarce and highly variable sand supply and occasional years of large reservoir releases, the long-term (2006-2015) sand mass balance for the upstream half of Marble Canyon is indeterminant and is positive for the downstream half of Marble Canyon. The apparent success of managing sand in Grand Canyon under deficit conditions suggests that fine sediment management protocols might be developed for other regulated rivers. Implementation would require establishment of networks of

  15. Endoscopic ultrasound-guided fine needle aspiration and biopsy using a 22-gauge needle with side fenestration in pancreatic cystic lesions.

    Science.gov (United States)

    Barresi, Luca; Tarantino, Ilaria; Traina, Mario; Granata, Antonino; Curcio, Gabriele; Azzopardi, Neville; Baccarini, Paola; Liotta, Rosa; Fornelli, Adele; Maimone, Antonella; Jovine, Elio; Cennamo, Vincenzo; Fabbri, Carlo

    2014-01-01

    Cytologic diagnosis by endoscopic ultrasound-guided fine needle aspiration is associated with low sensitivity and adequacy. A newly designed endoscopic ultrasound-guided fine needle biopsy device, endowed with a side fenestration, is now available. We carried out a study with the aim of evaluating the feasibility, safety, and diagnostic yield of the 22-gauge needle with side fenestration for endoscopic ultrasound fine needle aspiration and biopsy of pancreatic cystic lesions. 58 patients with 60 pancreatic cystic lesions consecutively referred for endoscopic ultrasound guided-fine needle aspiration were enrolled in a prospective, dual centre study, and underwent fine needle aspiration and biopsy with the 22-gauge needle with side fenestration. Fine needle aspiration and biopsy was technically feasible in all cases. In 39/60 (65%) pancreatic cystic lesions, the specimens were adequate for cyto-histologic assessment. In lesions with solid components, and in malignant lesions, adequacy was 94.4% (p = 0.0149) and 100% (p = 0.0069), respectively. Samples were adequate for histologic evaluation in 18/39 (46.1%) cases. There were only 2 (3.3%) mild complications. Fine needle aspiration and biopsy with the 22-gauge needle with side fenestration is feasible, and superior to conventional endoscopic ultrasound-guided fine needle aspiration cytology from cystic fluid, particularly in pancreatic cystic lesions with solid component or malignancy, with a higher diagnostic yield and with no increase in complication rate. Copyright © 2013 Editrice Gastroenterologica Italiana S.r.l. Published by Elsevier Ltd. All rights reserved.

  16. Numerical Model for Ultra-fine Particles in the Absence and Presence of Gravity

    Science.gov (United States)

    Dutt, Meenakshi; Elliott, James A.

    2009-06-01

    Length scales of particles and their surrounding medium strongly determines the nature of their interactions with one another and their responses to external fields. We are interested in systems of ultra-fine particles (0.1-1.0 micron) such as volcanic ash, soot from forest fires, solid aerosols, or fine powders for pharmaceutical inhalation applications. We have a developed a numerical model which captures the dominant physical interactions which control the behavior of these systems. The adhesive interactions between the particles use the Derjaguin-Muller-Toporov (DMT) adhesion theory along with the van der Waals attraction. The elastic restoring forces are modeled by the Hertz's contact model, and require details of material properties such as the Young's modulus and Poisson ratio. Commencing with a three dimensional gas of ultra-fine particles, the absence of gravity does not produce any noticeable clustering. The presence of gravity initially generates a large population of clusters with small number of particles, as the particles settle. The initial population of small clusters or single particles which have settled decrease with time as more particles, or clusters, agglomerate with one another. Our final results show clusters containing 10 to 100 particles, with a larger population of small clusters. We present details of the model, and some preliminary results which demonstrate the influence of the particle surface properties on the clustering dynamics of these systems, in the absence and presence of gravity (M. Dutt, J. A. Elliott, et al. in press).

  17. Fine needle aspiration biopsy to reestablish cell culture in an animal model of uveal melanoma.

    Science.gov (United States)

    Correa, Zelia Maria da Silva; Marshall, Jean-Claude; Souza Filho, João Pessoa; Odashiro, Alexandre Nakao; Burnier Jr, Miguel Noel

    2009-01-01

    To access the reliability of fine-needle aspiration biopsy in harvesting a sufficient amount of viable melanoma cells to establish a cell culture and maintain a melanoma cell line from an animal model of uveal melanoma. For this study, fifteen male New Zealand albino rabbits had their right eye surgically inoculated with uveal melanoma cell line 92.1. The animals were immunosupressed with cyclosporine A using a dose schedule previously published. The animals were followed for 12 weeks. Intraocular tumor growth was monitored weekly by indirect ophthalmoscopy. After the fourth week, one animal was sacrificed per week preceded by fine-needle aspiration biopsy using a sharp 25-gauge, 1-inch long needle. Two separate aspirates were made from different areas of the tumor. Each aspirate was flushed to a separate cell culture media and sent for cell culture. The cells were frozen after two weeks when there were at least 1 million cells, which is enough to maintain a cell line. Cells were defrosted for HMB-45 immuno-stains to confirm the melanoma origin. Cell growth was observed from the samples harvested from 11 out of the 15 animals inoculated with uveal melanoma. All cell cultures, after defrost, immunoassayed positive for HMB-45. Fine needle aspiration biopsy seems to be a reliable method to harvest cells from solid intraocular melanomas in an animal model, to establish cell culture and to maintain a melanoma cell line.

  18. Applied mechanics of solids

    CERN Document Server

    Bower, Allan F

    2009-01-01

    Modern computer simulations make stress analysis easy. As they continue to replace classical mathematical methods of analysis, these software programs require users to have a solid understanding of the fundamental principles on which they are based. Develop Intuitive Ability to Identify and Avoid Physically Meaningless Predictions Applied Mechanics of Solids is a powerful tool for understanding how to take advantage of these revolutionary computer advances in the field of solid mechanics. Beginning with a description of the physical and mathematical laws that govern deformation in solids, the text presents modern constitutive equations, as well as analytical and computational methods of stress analysis and fracture mechanics. It also addresses the nonlinear theory of deformable rods, membranes, plates, and shells, and solutions to important boundary and initial value problems in solid mechanics. The author uses the step-by-step manner of a blackboard lecture to explain problem solving methods, often providing...

  19. Cathodic stripping voltammetry of cysteine using silver and copper solid amalgam electrodes.

    Science.gov (United States)

    Yosypchuk, B; Novotný, L

    2002-04-01

    Silver and copper solid amalgam electrodes (modified with mercury meniscus and based on amalgamation of fine metallic powder) have been successfully tested for cathodic stripping voltammetry of cysteine. In the case of the silver solid amalgam electrode AgSAE the relative standard deviation (RSD) and the detection limit (3 SD) reached +/-2.3% and 3x10(-9) mol l(-1) cysteine, respectively.

  20. Coagulation of fines in fluorite froth flotation; Coagulacion de finos en la flotacion de la fluorita

    Energy Technology Data Exchange (ETDEWEB)

    Sarquis, P. E.; Gonzalez, M.; Moyano, A.; Bazan, V.

    2011-07-01

    Fluorite, a valuable mineral in the metallurgical industry, can be found together with silicates, carbonates and oxides in ore deposits. Commercial concentrates with more than 95 % of CaF{sub 2} are obtained processing the mineral in flotation plants and using oleic acid as fluorite collector. Depressor reagents such as sodium silicate, tannin and sodium carbonate are commonly employed to allow the oleic acid selective performance. These reagents cause a dispersant effect separating the solid-liquid solution on tailing plants. Fine particles in the recovered water enter the circuit and affect the flotation efficiency. The effect of coagulant ions was studied as a method to clarify the returned water. The problem of the presence of these ions is related to its reactions with the collector by the formation of compounds and possibly on the selectivity. Variable quantities of Al{sup 3}+, Fe{sup 3}+ and Ca{sup 2}+ ions were added to the flotation to evaluate its effect on the fluorite recovery, in the selectivity and in solids content in recirculation water. Results show that some ions fail to improve water quality and are detrimental to flotation. On the contrary, some ions contribute to reduce fine content in suspension. Therefore, although there is a recovery reduction, such effect can be counteracted increasing the collector consumption a little. (Author) 21 refs.

  1. Fine tuning of cytosolic Ca 2+ oscillations

    Science.gov (United States)

    Dupont, Geneviève; Combettes, Laurent

    2016-01-01

    Ca 2+ oscillations, a widespread mode of cell signaling, were reported in non-excitable cells for the first time more than 25 years ago. Their fundamental mechanism, based on the periodic Ca 2+ exchange between the endoplasmic reticulum and the cytoplasm, has been well characterized. However, how the kinetics of cytosolic Ca 2+ changes are related to the extent of a physiological response remains poorly understood. Here, we review data suggesting that the downstream targets of Ca 2+ are controlled not only by the frequency of Ca 2+ oscillations but also by the detailed characteristics of the oscillations, such as their duration, shape, or baseline level. Involvement of non-endoplasmic reticulum Ca 2+ stores, mainly mitochondria and the extracellular medium, participates in this fine tuning of Ca 2+ oscillations. The main characteristics of the Ca 2+ exchange fluxes with these compartments are also reviewed. PMID:27630768

  2. The composition of fine fragrances is changing

    DEFF Research Database (Denmark)

    Rastogi, Suresh Chandra; Menné, Torkil; Johansen, Jeanne Duus

    2003-01-01

    . The products with the highest concentrations of allergens have been shown to be prestige perfumes intended for women. This investigation explores the possible development in formulation of prestige perfumes, with regard to their content of the chemically defined ingredients of the diagnostic patch test...... material, the fragrance mix (FM). 10 fine fragrances were subjected to chemical analysis: 5 of these had been launched years ago (1921-1990) and 5 were the latest launches by the same companies, introduced 2 months to 4 years before purchase. The analysis revealed that the 5 old perfumes contained a mean...... of 5 of the 7 target allergens of the FM, while the new perfumes contained a mean of 2.8 of the allergens. The mean concentrations of the target allergens were 2.6 times higher in the old perfumes than in the new perfumes, range 2.2-337. It is concluded that the old perfumes, which are still popular...

  3. Magnetic Tension of Sunspot Fine Structures

    CERN Document Server

    Venkatakrishnan, P

    2010-01-01

    The equilibrium structure of sunspots depends critically on its magnetic topology and is dominated by magnetic forces. Tension force is one component of the Lorentz force which balances the gradient of magnetic pressure in force-free configurations. We employ the tension term of the Lorentz force to clarify the structure of sunspot features like penumbral filaments, umbral light bridges and outer penumbral fine structures. We compute vertical component of tension term of Lorentz force over two active regions namely NOAA AR 10933 and NOAA AR 10930 observed on 05 January 2007 and 12 December 2006 respectively. The former is a simple while latter is a complex active region with highly sheared polarity inversion line (PIL). The vector magnetograms used are obtained from Hinode(SOT/SP). We find an inhomogeneous distribution of tension with both positive and negative signs in various features of the sunspots. The existence of positive tension at locations of lower field strength and higher inclination is compatible...

  4. [Fine needle aspiration cytology of mammography screening

    DEFF Research Database (Denmark)

    Engvad, B.; Laenkholm, A.V.; Schwartz, Thue W.

    2009-01-01

    INTRODUCTION: In the year 2000 a quality assurance programme for the preoperative breast diagnostics was introduced in Denmark. The programme was based on the "European guidelines for quality assurance in breast cancer screening and diagnosis" where - among other measures - five cytological...... diagnostic classes were introduced. The aim of this study was to evaluate the quality assurance programme in a screening population to determine whether fine needle aspiration cytology (FNAC) as first choice remains a useful tool in the preoperative diagnostics, or if needle core biopsy should be the first...... of 66% of the 783 FNACs had a malignant cytology diagnosis, which in 99% of the cases turned out to be the correct diagnosis. Four lesions were false positives all of which represented benign proliferative breast diseases. The surgical procedures in these cases were either excisional biopsy...

  5. The fine structure constant and numerical alchemy

    CERN Document Server

    Dattoli, Giuseppe

    2010-01-01

    We comment on past and more recent efforts to derive a formula yielding the fine structure constant in terms of integers and transcendent numbers. We analyse these "exoteric" attitudes and describe the myths regarding {\\alpha}, which seems to have very ancient roots, tracing back to Cabbala and to medieval alchemic conceptions. We discuss the obsession for this constant developed by Pauli and the cultural "environment" in which such an "obsession" grew. We also derive a simple formula for {\\alpha} in terms of two numbers {\\pi} and 137 only. The formula we propose reproduces the experimental values up to the last significant digit, it has not any physical motivation and is the result of an alchemic combination of numbers. We make a comparison with other existing formulae, discuss the relevant limits of validity by comparison with the experimental values and discuss a criterion to recover a physical meaning, if existing, from their mathematical properties.

  6. Fine needle aspiration biopsy of ophthalmic tumors☆

    Science.gov (United States)

    Singh, Arun D.; Biscotti, Charles V.

    2012-01-01

    A majority of intraocular tumors can be diagnosed based on clinical examination and ocular imaging studies, which obviate the need for diagnostic ophthalmic fine needle aspiration biopsy (FNAB). Overall, diagnostic accuracy of ophthalmic FNAB is high but limited cellularity can compromise the diagnostic potential of ophthalmic aspirate samples. The role of ophthalmic FNAB is limited in retinal tumors. Orbital FNAB should be considered in the evaluation of lacrimal gland tumors, orbital metastasis, and lymphoproliferative lesions. Negative cytologic diagnosis of malignancy should not be considered unequivocal proof that an intraocular malignancy does not exist. With improved understanding of genetic prognostic factors of uveal melanoma, ophthalmic FNAB is gaining popularity for prognostic purposes in combination with eye conserving treatment of the primary tumor. In special clinical indications, ancillary studies such as immunohistochemistry and FISH can be performed on ophthalmic FNAB samples. Assistance of an experienced cytopathologist cannot be overemphasized. PMID:23960981

  7. Some characteristics of fine beryllium particle combustion

    Science.gov (United States)

    Davydov, D. A.; Kholopova, O. V.; Kolbasov, B. N.

    2007-08-01

    Beryllium dust will be produced under plasma interaction with beryllium armor of the first wall in ITER. Exothermal reaction of this dust with water steam or air, which can leak into the reactor vacuum chamber in some accidents, gives concern in respect to reactor safety. Results of studies devoted to combustion of fine beryllium particles are reviewed in the paper. A chemically active medium and elevated temperature are prerequisite to the combustion of beryllium particles. Their ignition is hampered by oxide films, which form a diffusion barrier on the particle surface as a result of pre-flame oxidation. The temperature to initiate combustion of particles depends on flame temperature, particle size, composition of combustible mixture, heating rate and other factors. In mixtures enriched with combustible, the flame temperature necessary to ignite individual particles approaches the beryllium boiling temperature.

  8. Subset Feature Learning for Fine-Grained Category Classification

    OpenAIRE

    Ge, Zongyuan; McCool, Christopher; Sanderson, Conrad; Corke, Peter

    2015-01-01

    Fine-grained categorisation has been a challenging problem due to small inter-class variation, large intra-class variation and low number of training images. We propose a learning system which first clusters visually similar classes and then learns deep convolutional neural network features specific to each subset. Experiments on the popular fine-grained Caltech-UCSD bird dataset show that the proposed method outperforms recent fine-grained categorisation methods under the most difficult sett...

  9. A case study on fine weather in Western Antarctic Peninsula

    Institute of Scientific and Technical Information of China (English)

    黄耀荣; 许淙; 尹涛; 张海影

    2001-01-01

    Great Wall Station, the local fine weather was studied. Pressure, temperature and humidity field, and aerological stratification were analyzed synoptically. Two kinds of fine weather with different physical characteristics were found; one was caused by the spreading of subtropical high with high temerature and high humidity, and another was connected with polar highwith low temperature and low humidity. The research provide a synoptic background for the local fine weather forecast.

  10. Fine structure of charge exchange lines observed in laboratory plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Ida, K.; Nishimura, S. [National Inst. for Fusion Science, Nagoya (Japan); Kondo, K.

    1997-01-01

    The influence of the fine structure of charge exchange lines appears only at the plasma edge or in the recombining phase where the ion temperature is low enough. The observed spectra in Li III and C VI are consistent with the sum of fine-structure components populated by statistical weights (assuming complete l-mixing) not by direct charge exchange cross sections. Some discrepancy was observed in the intensity ratio of fine-structure components between the observation and calculation for C VI in the recombining phase. The fine-structure of charge exchange lines gives an apparent Doppler shift in plasma rotation velocity measurement using charge exchange spectroscopy. (author)

  11. An Einstein-Cartan Fine Structure Constant Definition

    Directory of Open Access Journals (Sweden)

    Stone R. A. Jr.

    2010-01-01

    Full Text Available The fine structure constant definition given in Stone R.A. Jr. Progress in Physics, 2010, v.1, 11-13 is compared to an Einstein-Cartan fine structure constant definition. It is shown that the Einstein-Cartan definition produces the correct pure theory value, just not the measure value. To produce the measured value, the pure theory Einstein-Cartan fine structure constant requires only the new variables and spin coupling of the fine structure constant definition in [1].

  12. Implications of a Time-Varying Fine Structure Constant

    CERN Document Server

    Alfonso-Faus, A

    2002-01-01

    Much work has been done after the possibility of a fine structure constant being time-varying. It has been taken as an indication of a time-varying speed of light. Here we prove that this is not the case. We prove that the speed of light may or may not vary with time, independently of the fine structure constant being constant or not. Time variations of the speed of light, if present, have to be derived by some other means and not from the fine structure constant. No implications based on the possible variations of the fine structure constant can be imposed on the speed of light.

  13. Cell fine structure and function - Past and present

    Science.gov (United States)

    Fernandez-Moran, H.

    1970-01-01

    Electron microscopic studies of nerve membrane fine structure, discussing cell membrane multienzyme and macromolecular energy and information transduction, protein synthesis and nucleic acids interrelations

  14. Multifunctional solid/solid phononic crystal

    Science.gov (United States)

    Swinteck, N.; Vasseur, J. O.; Hladky-Hennion, A. C.; Croënne, C.; Bringuier, S.; Deymier, P. A.

    2012-07-01

    A two-dimensional, solid/solid phononic crystal (PC) comprised a square array of steel cylinders in epoxy is shown to perform a variety of spectral, wave vector, and phase-space functions. Over a range of operating frequencies, the PC's elastic band structure shows uniquely shaped equifrequency contours that are only accessible to excitations of longitudinal polarization. Under this condition, the PC is shown to behave as (1) an acoustic wave collimator, (2) a defect-less wave guide, (3) a directional source for elastic waves, (4) an acoustic beam splitter, (5) a phase-control device, and (6) a k-space multiplexer. Wave vector diagrams and finite-difference time-domain simulations are employed to authenticate the above mentioned capabilities.

  15. Quad-plane stereoscopic PIV for fine-scale structure measurements in turbulence

    Science.gov (United States)

    Naka, Y.; Tomita, K.; Shimura, M.; Fukushima, N.; Tanahashi, M.; Miyauchi, T.

    2016-05-01

    The fine-scale structure in turbulence is investigated by quad-plane stereoscopic particle image velocimetry (QPSPIV). The quad-plane consists of two each of different polarizations and wavelengths, and it provides three velocity components at four independent parallel planes. Measurements have been undertaken in the developed region of a turbulent round jet with a spatial resolution sufficient to capture the small-scale structures. The advantage of the QPSPIV is presented in terms of the spectral response in the evaluation of the out-of-plane velocity gradient. The full velocity gradient tensor is computed with a fourth-order finite difference scheme in the out-of-plane direction as well as the in-plane directions. The turbulence quantities, such as the vorticity components, the energy dissipation rate and the second and third invariants of the velocity gradient tensor, are computed according to their faithful definitions. The coherent fine-scale eddies are extracted from the present QPSPIV data. The probability density functions of the diameter and the maximum azimuthal velocity of the extracted eddies exhibit their peak at approximately 8η and 1.5u_k, respectively, where η and u_k are the Kolmogorov length and velocity. These values agree well with the data in the literature. The phase-averaged distributions of turbulence quantities around the coherent fine-scale eddy indicate an apparent elliptic feature around the axis. Furthermore, the state of the strain rate exerting the eddy is quantified from the phase-averaged distributions of eigenvalues of the strain rate tensor and the alignment of the corresponding eigenvectors against the axis. The present study gives a solid experimental support of the coherent fine-scale structures in turbulence, and the technique can be applied to various flow fields and to the higher Reynolds number condition.

  16. An Overview of Pickering Emulsions: Solid-Particle Materials, Classification, Morphology, and Applications

    Directory of Open Access Journals (Sweden)

    Yunqi Yang

    2017-05-01

    Full Text Available Pickering emulsion, a kind of emulsion stabilized only by solid particles locating at oil–water interface, has been discovered a century ago, while being extensively studied in recent decades. Substituting solid particles for traditional surfactants, Pickering emulsions are more stable against coalescence and can obtain many useful properties. Besides, they are more biocompatible when solid particles employed are relatively safe in vivo. Pickering emulsions can be applied in a wide range of fields, such as biomedicine, food, fine chemical synthesis, cosmetics, and so on, by properly tuning types and properties of solid emulsifiers. In this article, we give an overview of Pickering emulsions, focusing on some kinds of solid particles commonly serving as emulsifiers, three main types of products from Pickering emulsions, morphology of solid particles and as-prepared materials, as well as applications in different fields.

  17. Low-Dimensional Solids

    CERN Document Server

    Bruce, Duncan W; O'Hare, Dermot

    2010-01-01

    With physical properties that often may not be described by the transposition of physical laws from 3D space across to 2D or even 1D space, low-dimensional solids exhibit a high degree of anisotropy in the spatial distribution of their chemical bonds. This means that they can demonstrate new phenomena such as charge-density waves and can display nanoparticulate (0D), fibrous (1D) and lamellar (2D) morphologies. Low-Dimensional Solids presents some of the most recent research into the synthesis and properties of these solids and covers: Metal Oxide Nanoparticles; Inorganic Nanotubes and Nanowir

  18. Applications in solid mechanics

    DEFF Research Database (Denmark)

    Ølgaard, Kristian Breum; Wells, Garth N.

    2012-01-01

    Problems in solid mechanics constitute perhaps the largest field of application of finite element methods. The vast majority of solid mechanics problems involve the standard momentum balance equation, posed in a Lagrangian setting, with different models distinguished by the choice of nonlinear...... or linearized kinematics, and the constitutive model for determining the stress. For some common models, the constitutive relationships are rather complex. This chapter addresses a number of canonical solid mechanics models in the context of automated modeling, and focuses on some pertinent issues that arise...

  19. Solid propellant motor

    Science.gov (United States)

    Shafer, J. I.; Marsh, H. E., Jr. (Inventor)

    1978-01-01

    A case bonded end burning solid propellant rocket motor is described. A propellant with sufficiently low modulus to avoid chamber buckling on cooling from cure and sufficiently high elongation to sustain the stresses induced without cracking is used. The propellant is zone cured within the motor case at high pressures equal to or approaching the pressure at which the motor will operate during combustion. A solid propellant motor with a burning time long enough that its spacecraft would be limited to a maximum acceleration of less than 1 g is provided by one version of the case bonded end burning solid propellant motor of the invention.

  20. The solid state maser

    CERN Document Server

    Orton, J W; Walling, J C; Ter Haar, D

    1970-01-01

    The Solid State Maser presents readings related to solid state maser amplifier from the first tentative theoretical proposals that appeared in the early 1950s to the successful realization of practical devices and their application to satellite communications and radio astronomy almost exactly 10 years later. The book discusses a historical account of the early developments (including that of the ammonia maser) of solid state maser; the properties of paramagnetic ions in crystals; the development of practical low noise amplifiers; and the characteristics of maser devices designed for communica

  1. Laser cooling of solids

    OpenAIRE

    Nemova, Galina

    2009-01-01

    Parallel to advances in laser cooling of atoms and ions in dilute gas phase, which has progressed immensely, resulting in physics Nobel prizes in 1997 and 2001, major progress has recently been made in laser cooling of solids. I compare the physical nature of the laser cooling of atoms and ions with that of the laser cooling of solids. I point out all advantages of this new and very promising area of laser physics. Laser cooling of solids (optical refrigeration) at the present time can be lar...

  2. Landfill Mining - Wet mechanical treatment of fine MSW with a wet jigger.

    Science.gov (United States)

    Wanka, Sebastian; Münnich, Kai; Fricke, Klaus

    2017-01-01

    The motives for landfill mining are various. In the last couple of years Enhanced Landfill Mining (ELFM) has become increasingly important in academic discourse and practical implementation. The main goal of ELFM is to recover as much material as possible from deposited municipal solid waste (MSW). In most of the projects carried out so far, the main focus has been set on coarse materials such as plastics, woods, papers and metals. These fractions can be separated easily by sieving in combination with magnetic separation. In these projects most of the fine materials, which might represent as much as 60-70% of the total mass of the landfill body, had to be deposited again. A further treatment aiming at reducing the masses of these fine materials, which are still a conglomerate of soil, calorific fractions, metals, minerals and residues, usually did not take place. One topic in the framework of the landfill mining project TÖNSLM, in addition to the separation of the calorific fraction and metals has been the treatment of fine materials with the goal to re-use these e.g. for construction purposes. This paper shows the results obtained after the wet mechanical treatment of fine MSW 10-60mm with a wet jigger. The physical principle of this process is the separation of the mass flux due to the different densities of the waste constituents. As a result, three main waste fluxes are obtained: Dense inert and dense fine fraction with a high content of minerals and a lightweight fraction with a high calorific value between 16 and 20MJ/kg. An additional positive effect of wet mechanical treatment is the removal of the finest particles from the surface of the waste material, thus increasing the quality of the generated waste fluxes. The mass fluxes of the different fractions and their qualities as well as possible recovery paths are described below. An economical and ecological consideration of the treatment of the fine materials does not take place within the framework of

  3. Hydrogen Reduction of Hematite Ore Fines to Magnetite Ore Fines at Low Temperatures

    Directory of Open Access Journals (Sweden)

    Wenguang Du

    2017-01-01

    Full Text Available Surplus coke oven gases (COGs and low grade hematite ores are abundant in Shanxi, China. Our group proposes a new process that could simultaneously enrich CH4 from COG and produce separated magnetite from low grade hematite. In this work, low-temperature hydrogen reduction of hematite ore fines was performed in a fixed-bed reactor with a stirring apparatus, and a laboratory Davis magnetic tube was used for the magnetic separation of the resulting magnetite ore fines. The properties of the raw hematite ore, reduced products, and magnetic concentrate were analyzed and characterized by a chemical analysis method, X-ray diffraction, optical microscopy, and scanning electron microscopy. The experimental results indicated that, at temperatures lower than 400°C, the rate of reduction of the hematite ore fines was controlled by the interfacial reaction on the core surface. However, at temperatures higher than 450°C, the reaction was controlled by product layer diffusion. With increasing reduction temperature, the average utilization of hydrogen initially increased and tended to a constant value thereafter. The conversion of Fe2O3 in the hematite ore played an important role in the total iron recovery and grade of the concentrate. The grade of the concentrate decreased, whereas the total iron recovery increased with the increasing Fe2O3 conversion.

  4. Solid-liquid separation in the mining industry

    CERN Document Server

    Concha A , Fernando

    2014-01-01

    This book covers virtually all of the engineering science and technological aspects of separating water from particulate solids in the mining industry. It starts with an introduction to the field of mineral processing and the importance of water in mineral concentrators. The consumption of water in the various stages of concentration is discussed, as is the necessity of recovering the majority of that water for recycling. The book presents the fundamentals under which processes of solid-liquid separation are studied, approaching mixtures of discrete finely divided solid particles in water as a basis for dealing with sedimentation in particulate systems. Suspensions, treated as continuous media, provide the basis of sedimentation, flows through porous media and filtration. The book also considers particle aggregations, and thickening is analyzed in depth. Lastly, two chapters cover the fundamentals and application of rheology and the transport of suspensions.  This work is suitable for researchers and profess...

  5. Physical limitations to the spatial resolution of solid-state detectors

    CERN Document Server

    Boronat, M; Frey, A; Garcia, I; Schwenker, B; Vos, M; Wilk, F

    2015-01-01

    In this paper we explore the effect of -ray emission and fluctuations in the signal deposition on the detection of charged particles in silicon-based detectors. We show that these two effects ultimately limit the resolution that can be achieved by interpolation of the signal in finely segmented position-sensitive solid-state devices.

  6. Solid Waste Treatment Technology

    Science.gov (United States)

    Hershaft, Alex

    1972-01-01

    Advances in research and commercial solid waste handling are offering many more processing choices. This survey discusses techniques of storage and removal, fragmentation and sorting, bulk reduction, conversion, reclamation, mining and mineral processing, and disposal. (BL)

  7. Solids Accumulation Scouting Studies

    Energy Technology Data Exchange (ETDEWEB)

    Duignan, M. R.; Steeper, T. J.; Steimke, J. L.

    2012-09-26

    The objective of Solids Accumulation activities was to perform scaled testing to understand the behavior of remaining solids in a Double Shell Tank (DST), specifically AW-105, at Hanford during multiple fill, mix, and transfer operations. It is important to know if fissionable materials can concentrate when waste is transferred from staging tanks prior to feeding waste treatment plants. Specifically, there is a concern that large, dense particles containing plutonium could accumulate in poorly mixed regions of a blend tank heel for tanks that employ mixing jet pumps. At the request of the DOE Hanford Tank Operations Contractor, Washington River Protection Solutions, the Engineering Development Laboratory of the Savannah River National Laboratory performed a scouting study in a 1/22-scale model of a waste staging tank to investigate this concern and to develop measurement techniques that could be applied in a more extensive study at a larger scale. Simulated waste tank solids: Gibbsite, Zirconia, Sand, and Stainless Steel, with stainless steel particles representing the heavier particles, e.g., plutonium, and supernatant were charged to the test tank and rotating liquid jets were used to mix most of the solids while the simulant was pumped out. Subsequently, the volume and shape of the mounds of residual solids and the spatial concentration profiles for the surrogate for heavier particles were measured. Several techniques were developed and equipment designed to accomplish the measurements needed and they included: 1. Magnetic particle separator to remove simulant stainless steel solids. A device was designed and built to capture these solids, which represent the heavier solids during a waste transfer from a staging tank. 2. Photographic equipment to determine the volume of the solids mounds. The mounds were photographed as they were exposed at different tank waste levels to develop a composite of topographical areas. 3. Laser rangefinders to determine the volume of

  8. Solid Earth: Introduction

    Science.gov (United States)

    Rummel, R.

    1991-10-01

    The principles of the solid Earth program are introduced. When considering the study of solid Earth from space, satellites are used as beacons, inertial references, free fall probes and carrying platforms. The phenomenon measured by these satellites and the processes which can be studied as a result of these measurements are tabulated. The NASA solid Earth program focusses on research into surface kinematics, Earth rotation, land, ice, and ocean monitoring. The ESA solid Earth program identifies as its priority the Aristoteles mission for determining the gravity and magnetic field globally, with high spatial resolution and high accuracy. The Aristoteles mission characteristics and goals are listed. The benefits of the improved gravity information that will be provided by this mission are highlighted. This information will help in the following research: geodesy, orbit mechanics, geodynamics, oceanography, climate sea level, and the atmosphere.

  9. Solid Waste Management Districts

    Data.gov (United States)

    Vermont Center for Geographic Information — The Solid waste management districts layer is part of a dataset that contains administrative boundaries for Vermont's Agency of Natural Resources. This dataset...

  10. Gases, liquids and solids

    CERN Document Server

    Tabor, David

    1969-01-01

    It has been tradional to treat gases, liquids and solids as if they were completely unrelated material. However, this book shows that many of their bulk properties can been explained in terms of intermolecular forces.

  11. Study on Behaviour of Concrete Mix Replaceing Fine Aggregate With Steel Slag At Different Properties

    Directory of Open Access Journals (Sweden)

    P.Sateesh Kumar

    2015-11-01

    Full Text Available This paper aims to study experimentally, the effect of partial replacement of fine aggregate by steel slag (ss, on the various strength and durability properties of concrete by using the mix designs .the optimum percentage of replacement of fine aggregate by steel slag is found. Workability of concrete gradually decreases, as the percentage of replacement increases which is found using slump test. Compressive strength, tensile strength, flexural strength and durability tests such as acid resistant’s, using HCL,H2SO4 and rapid chloride penetration, are experimentally investigated. The results indicate that for conventional concrete, partial replacement of concrete by steel slag improves the compressive, tensile, flexural strength. The mass loss in cubes after immersion in acids is found to be very low. Deflection in the RCC beams gradually increases, as the load on the beam increases, for the replacement. The degree of fluoride ion penetrability is assessed based on the limits given in ASTM C 1202. The viability of use of steel slag in concrete is found. Waste management is one of the most common and challenging problems in the world. The steel making industry has generated substantially solid waste. Steel slag is a residue obtained in steel making operation. This paper deals with the implementation of steel slag as an effective replacement for sand. Steel slag ,which is consider as the solid waste pollutant, can be used for road construction ,clinker raw materials, filling materials etc. In this work, steel slag used as replacement for sand, which is also major component concrete mixture. This method can be implement for producing hallow blocks, solid blocks, paver blocks, concrete structures etc. Accordingly, advantages can be achieved by using steel slag instead of natural aggregates this will also encourage other researchers to find another field of using steel slag.

  12. Solid model design simplification

    Energy Technology Data Exchange (ETDEWEB)

    Ames, A.L.; Rivera, J.J.; Webb, A.J.; Hensinger, D.M.

    1997-12-01

    This paper documents an investigation of approaches to improving the quality of Pro/Engineer-created solid model data for use by downstream applications. The investigation identified a number of sources of problems caused by deficiencies in Pro/Engineer`s geometric engine, and developed prototype software capable of detecting many of these problems and guiding users towards simplified, useable models. The prototype software was tested using Sandia production solid models, and provided significant leverage in attacking the simplification problem.

  13. Organic Molecular Solids

    CERN Document Server

    Schwoerer, Marcus

    2007-01-01

    This is the first comprehensive textbook on the physical aspects of organic solids. All phenomena which are necessary in order to understand modern technical applications are being dealt with in a way which makes the concepts of the topics accessible for students. The chapters - from the basics, production and characterization of organic solids and layers to organic semiconductors, superconductors and opto-electronical applications - have been arranged in a logical and well thought-out order.

  14. Solid State Research

    Science.gov (United States)

    1993-01-31

    intermediate-field Meissner region, and high-field Bean model . The solid line is a fit of RsM = a + b(f,T)Hrf 2 to the results in the Meissner region...model the results: low-field weak links, intermediate-field Meissner region, and high-field Bean model The solid line is a fit of R1 M-- a + b (f T) Hff

  15. Measurements of Ultra-fine and Fine Aerosol Particles over Siberia: Large-scale Airborne Campaigns

    Science.gov (United States)

    Arshinov, Mikhail; Paris, Jean-Daniel; Stohl, Andreas; Belan, Boris; Ciais, Philippe; Nédélec, Philippe

    2010-05-01

    In this paper we discuss the results of in-situ measurements of ultra-fine and fine aerosol particles carried out in the troposphere from 500 to 7000 m in the framework of several International and Russian State Projects. Number concentrations of ultra-fine and fine aerosol particles measured during intensive airborne campaigns are presented. Measurements carried over a great part of Siberia were focused on particles with diameters from 3 to 21 nm to study new particle formation in the free/upper troposphere over middle and high latitudes of Asia, which is the most unexplored region of the Northern Hemisphere. Joint International airborne surveys were performed along the following routes: Novosibirsk-Salekhard-Khatanga-Chokurdakh-Pevek-Yakutsk-Mirny-Novosibirsk (YAK-AEROSIB/PLARCAT2008 Project) and Novosibirsk-Mirny-Yakutsk-Lensk-Bratsk-Novosibirsk (YAK-AEROSIB Project). The flights over Lake Baikal was conducted under Russian State contract. Concentrations of ultra-fine and fine particles were measured with automated diffusion battery (ADB, designed by ICKC SB RAS, Novosibirsk, Russia) modified for airborne applications. The airborne ADB coupled with CPC has an additional aspiration unit to compensate ambient pressure and changing flow rate. It enabled to classify nanoparticles in three size ranges: 3-6 nm, 6-21 nm, and 21-200 nm. To identify new particle formation events we used similar specific criteria as Young et al. (2007): (1) N3-6nm >10 cm-3, (2) R1=N3-6/N621 >1 and R2=N321/N21200 >0.5. So when one of the ratios R1 or R2 tends to decrease to the above limits the new particle formation is weakened. It is very important to notice that space scale where new particle formation was observed is rather large. All the events revealed in the FT occurred under clean air conditions (low CO mixing ratios). Measurements carried out in the atmospheric boundary layer over Baikal Lake did not reveal any event of new particle formation. Concentrations of ultra-fine

  16. Lyophilization -Solid Waste Treatment

    Science.gov (United States)

    Litwiller, Eric; Flynn, Michael; Fisher, John; Reinhard, Martin

    2004-01-01

    This paper discusses the development of a solid waste treatment system that has been designed for a Mars transit exploration mission. The technology described is an energy-efficient lyophilization technique that is designed to recover water from spacecraft solid wastes. Candidate wastes include feces, concentrated brines from water processors, and other solid wastes that contain free water. The system is designed to operate as a stand-alone process or to be integrated into the International Space Station Waste Collection System. In the lyophilization process, water in an aqueous waste is frozen and then sublimed, separating the waste into a dried solid material and liquid water. The sublimed water is then condensed in a solid ice phase and then melted to generate a liquid product. In the subject system the waste solids are contained within a 0.2 micron bio-guard bag and after drying are removed from the system and stored in a secondary container. This technology is ideally suited to applications such as the Mars Reference Mission, where water recovery rates approaching 100% are desirable but production of CO2 is not. The system is designed to minimize power consumption through the use of thermoelectric heat pumps. The results of preliminary testing of a prototype system and testing of the final configuration are provided. A mathematical model of the system is also described.

  17. Solid Mathematical Marbling.

    Science.gov (United States)

    Lu, Shufang; Jin, Xiaogang; Jaffer, Aubrey; Gao, Fei; Mao, Xiaoyang

    2016-05-25

    Years of research have been devoted to computer-generated two-dimensional marbling. However, three-dimensional marbling has yet to be explored. In this paper, we present mathematical marbling of three-dimensional solids which supports a compact random-access vector representation. Our solid marbling textures are created by composing closed-form 3D pattern tool functions. These tool functions are an injection function and five deformation functions. The injection function is used to generate basic patterns, and the deformation functions are responsible for transforming the basic pattern into complex marbling effects. The resulting representation is feature preserving and resolution-independent. Our approach can render high-quality images preserving both the sharp features and the smooth color variations of a solid texture. When implemented on the GPU, our representation enables efficient color evaluation during the real-time solid marbling texture mapping. The color of a point in the volume space is computed by the 3D pattern tool functions from its coordinates. Our method consumes very little memory because only the mathematical functions and their corresponding parameters are stored. In addition, we develop an intuitive user interface and a genetic algorithm to facilitate the solid marbling texture authoring process. We demonstrate the effectiveness of our approach through various solid marbling textures and 3D objects carved from them.

  18. Solid iron compressed up to 560 GPa.

    Science.gov (United States)

    Ping, Y; Coppari, F; Hicks, D G; Yaakobi, B; Fratanduono, D E; Hamel, S; Eggert, J H; Rygg, J R; Smith, R F; Swift, D C; Braun, D G; Boehly, T R; Collins, G W

    2013-08-09

    Dynamic compression by multiple shocks is used to compress iron up to 560 GPa (5.6 Mbar), the highest solid-state pressure yet attained for iron in the laboratory. Extended x-ray absorption fine structure (EXAFS) spectroscopy offers simultaneous density, temperature, and local-structure measurements for the compressed iron. The data show that the close-packed structure of iron is stable up to 560 GPa, the temperature at peak compression is significantly higher than expected from pure compressive work, and the dynamic strength of iron is many times greater than the static strength based on lower pressure data. The results provide the first constraint on the melting line of iron above 400 GPa.

  19. Carbon burnout project-coal fineness effects

    Energy Technology Data Exchange (ETDEWEB)

    Mike Celechin [Powergen UK plc, Nottingham (United Kingdom)

    2004-02-01

    The aim of this DTI project is to establish good quality plant and rig data to demonstrate the effect of changing coal fineness on carbon burnout in a controlled manner, which can then be used to support computational fluid dynamics (CFD) and engineering models of the process. The modelling elements of the project were completed by Mitsui Babcock Energy Ltd., and validated using the data produced by the other partners. The full scale plant trials were successfully completed at Powergen's Kingsnorth Power Station and a full set of tests were also completed on Powergen's CTF. During these test both carbon-in-ash and NOx levels were seen to increase with increasing fuel particle size. Laboratory analysis of fly ash produced during the plant and rig trials revealed that only small differences in char morphology and reactivity could be detected in samples produced under significantly different operating conditions. Thermo Gravimetric Analysis was also undertaken on a range of PF size fractions collected form mills operating at different conditions. 3 refs., 13 figs., 1 tab.

  20. Plant practices in fine coal column flotation

    Energy Technology Data Exchange (ETDEWEB)

    Davis, V.L. Jr.; Bethell, P.J.; Stanley, F.L. [Pittston Coal Management Co., Lebanon, VA (United States); Luttrell, G.H. [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States). Dept. of Mining and Minerals Engineering

    1995-10-01

    Five 3 m (10 ft) diameter Microcel{trademark} flotation columns were installed at Clinchfield Coal Company`s Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1.5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 {micro}m fraction while spirals are used to upgrade the plus 150 {micro}m material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery wa increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

  1. The Fine Structure of the Parathyroid Gland

    Science.gov (United States)

    Trier, Jerry Steven

    1958-01-01

    The fine structure of the parathyroid of the macaque is described, and is correlated with classical parathyroid cytology as seen in the light microscope. The two parenchymal cell types, the chief cells and the oxyphil cells, have been recognized in electron micrographs. The chief cells contain within their cytoplasm mitochondria, endoplasmic reticulum, and Golgi bodies similar to those found in other endocrine tissues as well as frequent PAS-positive granules. The juxtanuclear body of the light microscopists is identified with stacks of parallel lamellar elements of the endoplasmic reticulum of the ergastoplasmic or granular type. Oxyphil cells are characterized by juxtanuclear bodies and by numerous mitochondria found throughout their cytoplasm. Puzzling lamellar whorls are described in the cytoplasm of some oxyphil cells. The endothelium of parathyroid capillaries is extremely thin in some areas and contains numerous fenestrations as well as an extensive system of vesicles. The possible significance of these structures is discussed. The connective tissue elements found in the perivascular spaces of macaque parathyroid are described. PMID:13502423

  2. Space Telescope Fine Guidance Sensor Bearing Anomaly

    Science.gov (United States)

    Loewenthal, S.; Esper, J.; Pan, J.; Decker, J.

    1996-01-01

    Early in 1993, a servo motor within one of three Fine Guidance Sensors (FGS) aboard the Hubble Space Telescope (HST) reached stall torque levels on several occasions. Little time was left to plan replacement during the first servicing mission, scheduled at the end of '93. Accelerated bearing life tests confirmed that a small angle rocking motion, known as Coarse Track (CT), accelerated bearing degradation. Saturation torque levels were reached after approximately 20 million test cycles, similar to the flight bearings. Reduction in CT operation, implemented in flight software, extended FGS life well beyond the first servicing mission. However in recent years, bearing torques have resumed upward trends and together with a second, recent bearing torque anomaly has necessitated a scheduled FGS replacement during the upcoming second servicing mission in '97. The results from two series of life tests to quantify FGS bearing remaining life, discussion of bearing on-orbit performance, and future plans to service the FGS servos are presented in this paper.

  3. The fine art of ‘sourcery’

    CERN Multimedia

    2009-01-01

    The commissioning of the new Linac4 source – first element of the new acceleration chain for the upgrade of the LHC (sLHC) – started at the beginning of July. After years of preparation but after only a few hours of fine-tuning of the numerous parameters involved, the source has delivered its first negative ions. The civil engineering work for the new Linac4 going on near Restaurant 2.While the LHC is preparing for restart, teams of experts involved in the sLHC project are also working on the new facilities that will allow the LHC to run at higher luminosity. The beginning of the new chain of accelerators is Linac4, whose excavation works started October last year. "The particle source that we are commissioning now will be installed at the beginning of the path", explains Maurizio Vretenar, Linac4 project leader. "It is a critical element of the chain as all protons that will circulate in the CERN accelerators will originate from it." The Linac 4 source is differ...

  4. Fine needle aspiration cytology in leprosy

    Directory of Open Access Journals (Sweden)

    Prasad PVS

    2008-01-01

    Full Text Available Background: Laboratory diagnosis of leprosy by slit skin smear and skin biopsy is simple but both techniques have their own limitations. Slit skin smear is negative in paucibacillary cases whereas skin biopsy is an invasive technique. Fine needle aspiration cytology (FNAC from skin lesions in leprosy with subsequent staining with May-Grunwald-Giemsa (MGG stain has been found useful. Aim: To evaluate the possible role of cytology in classifying leprosy patients. Methods: Seventy-five untreated cases of leprosy attending the outpatient department were evaluated. Smears were taken from their skin lesions and stained using the MGG technique. Skin biopsy was also done from the lesions, which was compared with cytology smears. Results: A correlation of clinical features with FNAC was noticed in 87.5% of TT, 92.1% of BT, 81% of BL, and 66% of LL cases. Correlation of clinical with histopathological diagnoses revealed 12.5% specificity in TT leprosy, 55.3% in BT, 52.4% in BL and 50% in LL, and 100% in neuritic and histoid leprosy cases. Both correlations were found to be statistically significant by paired t test analysis. Thus, it was possible to distinguish the tuberculoid types by the presence of epithelioid cells and the lepromatous types by the presence of lymphocytes and foamy macrophages. Conclusion: FNAC may be used to categorize the patients into paucibacillary and multibacillary types, but is not a very sensitive tool to classify the patients across the Ridley-Jopling spectrum.

  5. Fine Sediment Resuspension Dynamics in Moreton Bay

    Institute of Scientific and Technical Information of China (English)

    YOU Zai-jin; YIN Bao-shu

    2007-01-01

    A comprehensive field study has been undertaken to investigate sediment resuspension dynamics in the Moreton Bay, a large semi-enclosed bay situated in South East Queensland, Australia. An instrumented tripod, which housed three current meters, three OBS sensors and one underwater video camera, was used to collect the field data on tides, currents, waves and suspended sediment concentrations at four sites (Sites 1, 2, 4, and 5) in the bay. Site 1 was located at the main entrance, Site 2 at the central bay in deep water, and Sites 4 and 5 at two small bays in shallow water. The bed sediment was fine sand (d50=0.2 mm) at Site 1, and cohesive sediment at the other three sites. Based on the collected field data, it is found that the dominant driving forces for sediment resuspension are a combination of ocean swell and tidal currents at Site 1, tidal currents at Site 2, and wind-waves at Sites 4 and 5. The critical bed shear stress for cohesive sediment resuspension is determined as 0.079 Pa in unidirectional flow at Site 2, and 0.076 Pa in wave-induced oscillatory flow at Site 5.

  6. Percutaneous transhepatic cholangiography using fine needle

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Kyoo Byung; Kim, Yun Hwan; Lee, Nam Joon; Suh, Won Hyuck [College of Medicine, Korea University, Seoul (Korea, Republic of)

    1980-12-15

    In recent years, percutaneous transhepatic cholangiography (PTC) using fine needle has become widely employed as the procedure of choice for direct opacification of the biliary trees because of its high success rate, easy performance and relative low complication rate. Authors present the clinical and PTC findings of experienced cases during last four years, from May 1976 to June 1980, at the Department of Radiology, Korea University Hospital. We tried to study of PTC in 44 cases, 32 males and 12 females, and succeeded in visualization of bile ducts in 41 cases, but the other three cases were failed to visualize the bile ducts. Final confirmative diagnosis was achieved in 29 cases by operation, laparoscopy and other clinical methods. The PTC diagnosis was correct in 24 of 29 cases, and the others were incorrect. The 29 final diagnosis was including 13 cases of biliary stones, 6 cases of biliary cancer, 3 cases of pancreatic cancer, 3 cases of clonorchiasis, one case of CBD ascariasis and 3 cases of others. Incorrect PTC diagnosis was made in five cases. They were one case of nonvisualized intrahepatic stones, one case of hepatoma PTC diagnosed as cholangiocarcinoma, one case of pancreatic cancer diagnosed as cholangiocarcinoma, one case of clonorchiasis diagnosed as biliary stones and one case of normal CBD which was diagnosed as distal CBD cancer. And we experienced one case of bile peritonitis as complication, who was 35 year-old female patient with multiple CBD stones, and aspirated about 500ml of bile stained ascites during operation.

  7. Cosmological Constant, Fine Structure Constant and Beyond

    CERN Document Server

    Wei, Hao; Li, Hong-Yu; Xue, Dong-Ze

    2016-01-01

    In this work, we consider the cosmological constant model $\\Lambda\\propto\\alpha^{-6}$, which is well motivated from three independent approaches. As is well known, the evidence of varying fine structure constant $\\alpha$ was found in 1998. If $\\Lambda\\propto\\alpha^{-6}$ is right, it means that the cosmological constant $\\Lambda$ should be also varying. In this work, we try to develop a suitable framework to model this varying cosmological constant $\\Lambda\\propto\\alpha^{-6}$, in which we view it from an interacting vacuum energy perspective. We propose two types of models to describe the evolutions of $\\Lambda$ and $\\alpha$. Then, we consider the observational constraints on these models, by using the 293 $\\Delta\\alpha/\\alpha$ data from the absorption systems in the spectra of distant quasars, and the data of type Ia supernovae (SNIa), cosmic microwave background (CMB), baryon acoustic oscillation (BAO). We find that the model parameters can be tightly constrained to the narrow ranges of ${\\cal O}(10^{-5})$ t...

  8. Granular mechanics of normally consolidated fine soils

    Science.gov (United States)

    Yanqui, Calixtro

    2017-06-01

    In this paper, duality is demonstrated to be one of the inherent properties of granular packings, by mapping the stress-strain curve into the diagram that relates the pore ratio and the localization of the contact point. In this way, it is demonstrated that critical state is not related to the maximum void ratio, but to a unique value related to two different angles of packing, one limiting the domain of the dense state, and other limiting the domain of the loose state. As a consequence, packings can be dilative or contractive, as mutually exclusive states, except by the critical state point, where equations for both granular packings are equally valid. Further analysis shows that stresses, in a dilative packing, are transmitted by chains of contact forces, and, in a contractive packing, by shear forces. So that, stresses, for the first case, depend on the initial void ratio, and, for the second case, are independent. As it is known, normally consolidated and lightly overconsolidated fine soils are in loose state, and, hence, their strength is constant, because it does not depend on their initial void ratio; except at the critical state, for which, the consolidated-drained angle of friction is related to the plasticity index or the liquid limit. In this fashion, experimental results reported by several authors around the world are confronted with the theory, showing a good agreement.

  9. Fine needle aspiration cytology of dermal cylindroma

    Directory of Open Access Journals (Sweden)

    Parikshaa Gupta

    2014-01-01

    Full Text Available In this paper, we have described fine needle aspiration cytology (FNAC of a rare case of dermal cylindroma. A 40-year-old female presented with a lateral mid-cervical swelling fixed to the skin. FNAC smears showed multiple clusters of small, round to oval cells with hyperchromatic nuclei, inconspicuous nucleoli and scant cytoplasm. In addition, the background showed deposits of basement membrane type material. This was dark magenta colored pinkish globular material. The globules were occasionally surrounded by the basal type of cells. Occasional cells with elongated nuclei were also noted. Cytological diagnosis of skin adnexal tumor possibly cylindroma was offered. Subsequent histopathology of the swelling showed sheets and clusters of cells in a jigsaw puzzle-like fashion. Deposition of abundant basement membrane-like material was noted in between the tumor cells. A diagnosis of cylindorma was offered. FNAC along with the subcutaneous location of the tumor and absence of primary salivary gland tumor may help to diagnose such rare case.

  10. FINE AND COARSE PARTICLES: CONCENTRATION RELATIONSHIPS RELEVANT TO EPIDEMIOLOGICAL STUDIES

    Science.gov (United States)

    Fine particles and coarse particles are defined in terms of the modal structure of particle size distributions typically observed in the atmosphere. Differences among the various modes are discussed. The fractions of fine and coarse particles collected in specific size ranges, ...

  11. Shrinkage and swelling properties of flocculated mature fine tailings

    NARCIS (Netherlands)

    Yao, Y.; Van Tol, A.F.; Van Paassen, L.A.; Vardon, P.J.

    2014-01-01

    In the atmospheric fines drying technique, mature fine tailings (MFT) are treated with polymers and deposited in thin layers on a sloped surface for sub-aerial drying. During the whole drying period, the tailings deposits can experience rewetting during periods of rainy weather or as result of the

  12. Helping Preschoolers Prepare for Writing: Developing Fine Motor Skills

    Science.gov (United States)

    Huffman, J. Michelle; Fortenberry, Callie

    2011-01-01

    Early childhood is the most intensive period for the development of physical skills. Writing progress depends largely on the development of fine motor skills involving small muscle movements of the hand. Young children need to participate in a variety of developmentally appropriate activities intentionally designed to promote fine motor control.…

  13. Subjugated in the Creative Industries The Fine Arts in Singapore

    DEFF Research Database (Denmark)

    Ooi, Can-Seng

    2011-01-01

    to economic value. Fine arts practices will not be as lucrative or popular as their counterparts in the other creative businesses; they will remain poor cousins in the creative industries. Essentially, the fine arts are being subjugated in the creative industries and the Singaporean art world is being changed....

  14. RSW Mixed Element Cell-Centered Fine Mesh

    Data.gov (United States)

    National Aeronautics and Space Administration — This is a RSW mixed-element unstructured fine mesh for cell-centered solvers. UG3 : Grid File Name = rsw_fine_mixedcc.b8.ugrid UG3 : Quad Surface Faces= 28968 UG3 :...

  15. A STUDY OF FINE PRECIPITATES IN ALLOYS BY POSITRON ANNIHILATION

    Institute of Scientific and Technical Information of China (English)

    王景成; 尤富强; 殷俊林; 高国华; 梁玲; 段勇

    2001-01-01

    Measurements were performed using the positron annihilation technique associated with physical metallurgical techniques for several engineering alloys containing fine precipitates. It is shown that positron annihilation is an effective method to detect fine precipitates, providing a sound basis for a further intense research of these.

  16. 7 CFR 400.454 - Disqualification and civil fines.

    Science.gov (United States)

    2010-01-01

    ... disqualification and civil fines will be imposed against: (i) Participants and other persons, except insurance... provision affects the approved insurance provider's responsibilities with respect to the service of existing... 7 Agriculture 6 2010-01-01 2010-01-01 false Disqualification and civil fines. 400.454 Section...

  17. Selective separation of fine particles by a new flotation approach

    NARCIS (Netherlands)

    Mulleneers, H.A.E.; Koopal, L.K.; Bruning, H.; Rulkens, W.H.

    2002-01-01

    Fine particles often create problems in flotation applications. In this article a new laboratory flotation system for the selective separation of small particles was designed and tested. The device contains an active counter current sedimentation that should prevent entrainment of the fine

  18. Deformation of fine-grained synthetic peridotite under wet conditions

    NARCIS (Netherlands)

    McDonnell, R.D.

    1997-01-01

    Fine-grained hydrated peridotite mylonites have been proposed to play an important role in controlling the strength of the continental lithosphere during rifting. For this reason, the deformation behaviour of wet fine-grained forsterite and forsterite-enstatite materials and the underlying deformati

  19. Search for Possible Variation of the Fine Structure Constant

    OpenAIRE

    2003-01-01

    Determination of the fine structure constant alpha and search for its possible variation are considered. We focus on a role of the fine structure constant in modern physics and discuss precision tests of quantum electrodynamics. Different methods of a search for possible variations of fundamental constants are compared and those related to optical measurements are considered in detail.

  20. Whole Brain Learning: The Fine Arts with Students at Risk

    Science.gov (United States)

    Respress, Trinetia; Lutfi, Ghazwan

    2006-01-01

    Schools are searching for more effective strategies that will enable all students to thrive and succeed. Evidence indicates that the fine arts can provide a unique avenue for reaching challenging students with principles of brain-based learning. This article describes HEARTS, an after-school fine arts program which taps and develops the talents of…

  1. Fines Classification Based on Sensitivity to Pore-Fluid Chemistry

    KAUST Repository

    Jang, Junbong

    2015-12-28

    The 75-μm particle size is used to discriminate between fine and coarse grains. Further analysis of fine grains is typically based on the plasticity chart. Whereas pore-fluid-chemistry-dependent soil response is a salient and distinguishing characteristic of fine grains, pore-fluid chemistry is not addressed in current classification systems. Liquid limits obtained with electrically contrasting pore fluids (deionized water, 2-M NaCl brine, and kerosene) are combined to define the soil "electrical sensitivity." Liquid limit and electrical sensitivity can be effectively used to classify fine grains according to their fluid-soil response into no-, low-, intermediate-, or high-plasticity fine grains of low, intermediate, or high electrical sensitivity. The proposed methodology benefits from the accumulated experience with liquid limit in the field and addresses the needs of a broader range of geotechnical engineering problems. © ASCE.

  2. Advanced treatment of oil recovery wastewater from polymer flooding by UV/H2O2/O3 and fine filtration

    Institute of Scientific and Technical Information of China (English)

    REN Guang-meng; SUN De-zhi; Jong Shik CHUNK

    2006-01-01

    In order to purify oil recovery wastewater from polymer flooding (ORWPF) in tertiary oil recovery in oil fields, advanced treatment of UV/H2O2/O3 and fine filtration were investigated. The experimental results showed that polyacrylamide and oil remaining in ORWPF after the conventional treatment process could be effectively removed by UV/H2O2/O3 process. Fine filtration gave a high performance in eliminating suspended solids. The treated ORWPF can meet the quality requirement of the wastewater-bearing polymer injection in oilfield and be safely re-injected into oil reservoirs for oil recovery.

  3. Analysis of Fine-Needle Biopsy Versus Fine-Needle Aspiration in Diagnosis of Pancreatic and Abdominal Masses: A Prospective, Multicenter, Randomized Controlled Trial.

    Science.gov (United States)

    Cheng, Bin; Zhang, Yueming; Chen, Qian; Sun, Bo; Deng, Zhuang; Shan, Hongbo; Dou, Lizhou; Wang, Jinglin; Li, Yawen; Yang, Xiujiang; Jiang, Tianan; Xu, Guoliang; Wang, Guiqi

    2017-07-19

    Endoscopic ultrasound (EUS)-guided fine needles with side fenestrations are used to collected aspirates for cytology analysis and biopsy samples for histologic analysis. We conducted a large, multicenter study to compare the accuracy of diagnosis via specimens collected with fine-needle biopsy (FNB) versus fine-needle aspiration (FNA) for patients with pancreatic and nonpancreatic masses. We performed a prospective single-blind study at 5 tertiary care centers in China. The study comprised 408 patients undergoing EUS for a solid mass (>1 cm) in the pancreas, abdomen, mediastinum, or pelvic cavity, from December 2014 through January 2016. Patients were randomly assigned to groups (1:1) for assessment by FNA (n = 190) or FNB (n = 187). After lesions were identified by EUS, samples were collected in a total of 4 passes by each needle. All procedures were performed by experienced endosonographers; cytologists and pathologists were blinded to the sample collection method. Patients were followed for at least 48 weeks, and final diagnoses were obtained after surgery, imaging analysis, or resolution of lesion. The primary aim was to compare diagnostic yields of EUS-FNA with EUS-FNB for all solid masses, then separately as pancreatic and nonpancreatic masses. The secondary endpoint was the quality of histologic specimen. Findings from FNB analysis were accurate for 91.44% of all cases, compared with 80.00% for all FNA cases, based on final patient diagnoses (P = .0015). In patients with pancreatic masses (n = 249), findings from histologic analysis of FNBs were accurate for 92.68% of the cases, compared with 81.75% for FNAs (P = .0099). In cytology analysis of pancreatic masses, samples collected by FNB accurately identified 88.62% of all pancreatic lesions, whereas samples collected by FNA accurately identified 79.37% (P = .00468). Analyses of samples of nonpancreatic masses collected by FNA versus FNB produced similar diagnostic yields. In a prospective study of

  4. Pressure Effects on Solid State Phase Transformation of Aluminium Bronze in Cooling Process

    Institute of Scientific and Technical Information of China (English)

    WANG Hai-Yan; CHEN Yan; LIU Yu-Wen; LI Fei; LIU Jian-Hua; PENG Gui-Rong; WANG Wen-Kui

    2009-01-01

    Effects of high pressure (6 GPa) on the solid state phase transformation kinetic parameters of aluminum bronze during the cooling process are investigated, based on the measurement and calculation of its solid state phase transformation temperature, duration and activation energy and the observation of its microstructures. The results show that high pressure treatment can reduce the solid phase transformation temperature and activation energy in the cooling process and can shorten the phase transformation duration, which is favorable when forming fine-grained aluminum bronze.

  5. MOTORIC STIMULATION RELATED TO FINE MOTORIC DEVELOPMENT ON CHILD

    Directory of Open Access Journals (Sweden)

    Mira Triharini

    2017-07-01

    Full Text Available Introduction: Motor developmental stimulation is an activity undertaken to stimulate the children basic skills and so they can grow and develop optimally. Children who obtain a direct stimulus will grow faster than who get less stimulus. Mother’s behavior of stimulation is very important for children, it is considering as the basic needs of children and it must be fulfilled. Providing good stimulation could optimize fine motor development in children. The purpose of this study was to analyze mother’s behavior about motor stimulation with fine motor development in toddler age 4-5 years old. Method: Design have been  used in this study was cross sectional. Population were mothers and their toddler in Group A of Dharma Wanita Persatuan Driyorejo Gresik Preschool. Sample were 51 respondents recruited by using purposive sampling technique according to inclusion and exclusion criteria. The independent variable was mother’s behavior about motor stimulation whereas dependent variable was fine motor development in toddler. The data were collected using questionnaire and conducting observation on fine motor development based on Denver Development Screening Test (DDST. Data then analyzed using Spearman Rho (r test to find relation between mother’s behaviors about stimulation motor on their toddler fine motor development. Result: Results  of this study showed that there were correlations between mother’s knowledge and fine motor development in toddler (p=0.000, between mother’s attitude and fine motor development in toddler (p=0.000, and between mother’s actions and fine motor development in toddler (p=0.000. Analysis: In sort study found that there were relation between fine motor development and mother’s behavior. Discussion: Therefore mother’s behavior needed to be improved. Further research about stimulation motor and fine motor development aspects in toddler is required.

  6. Fine velocity structures collisional dissipation in plasmas

    Science.gov (United States)

    Pezzi, Oreste; Valentini, Francesco; Veltri, Pierluigi

    2016-04-01

    In a weakly collisional plasma, such as the solar wind, collisions are usually considered far too weak to produce any significant effect on the plasma dynamics [1]. However, the estimation of collisionality is often based on the restrictive assumption that the particle velocity distribution function (VDF) shape is close to Maxwellian [2]. On the other hand, in situ spacecraft measurements in the solar wind [3], as well as kinetic numerical experiments [4], indicate that marked non-Maxwellian features develop in the three-dimensional VDFs, (temperature anisotropies, generation of particle beams, ring-like modulations etc.) as a result of the kinetic turbulent cascade of energy towards short spatial scales. Therefore, since collisional effects are proportional to the velocity gradients of the VDF, the collisionless hypothesis may fail locally in velocity space. Here, the existence of several characteristic times during the collisional relaxation of fine velocity structures is investigated by means of Eulerian numerical simulations of a spatially homogeneous force-free weakly collisional plasma. The effect of smoothing out velocity gradients on the evolution of global quantities, such as temperature and entropy, is discussed, suggesting that plasma collisionality can increase locally due to the velocity space deformation of the particle velocity distribution. In particular, by means of Eulerian simulations of collisional relaxation of a spatially homogeneous force-free plasma, in which collisions among particles of the same species are modeled through the complete Landau operator, we show that the system entropy growth occurs over several time scales, inversely proportional to the steepness of the velocity gradients in the VDF. We report clear evidences that fine velocity structures are dissipated by collisions in a time much shorter than global non-Maxwellian features, like, for example, temperature anisotropies. Moreover we indicate that, if small-scale structures

  7. EDITORIAL: Cluster issue on fine particle magnetism

    Science.gov (United States)

    Fiorani, D.

    2008-07-01

    This Cluster issue of Journal of Physics D: Applied Physics arises from the 6th International Conference on Fine Particle Magnetism (ICFPM) held in Rome during 9-12 October 2007 at the headquarters of the National Research Council (NCR). It contains a collection of papers based on both invited and contributed presentations at the meeting. The ICFPM Conferences have previously been held in Rome, Italy (1991), Bangor, UK (1996), Barcelona, Spain (1999), Pittsburgh, USA (2002) and London, UK (2004). The aim of this series of Conferences is to bring together the experts in the field of nanoparticle magnetism at a single forum to discuss recent developments in both theoretical and experimental aspects, and technological applications. The Conference programme included sessions on: new materials, novel synthesis and processing techniques, with special emphasis on self-organized magnetic arrays; theory and modelling; surface and interface properties; transport properties; spin dynamics; magnetization reversal mechanisms; magnetic recording media and permanent magnets; biomedical applications and advanced investigation techniques. I would like to thank the European Physical Society and the Innovative Magnetic and Superconducting Materials and Devices Project of the Materials and Devices Department and the Institute of Structure of Matter (ISM) of CNR for their support. Thanks are also due to the members of the Programme Committee, to the local Organizing Committee, chaired by Elisabetta Agostinelli and to all the Conference participants. I am also indebted to the many scientists who contributed to assuring the high-quality of this Cluster by donating their time to reviewing the manuscripts contained herein. Finally, I'd like to dedicate this issue to the memories of Jean Louis Dormann, a great expert in nanoparticle magnetism, who was one of the promoters and first organizers of this series of Conferences, and of Grazia Ianni, the Conference secretary, who died before her

  8. SURFACE TENSION OF MOLTEN IF STEEL CONTAINING Ti AND ITS INTERFACIAL PROPERTIES WITH SOLID ALUMINA

    Institute of Scientific and Technical Information of China (English)

    L.C. Zhong; M. Zeze; K. Mukai

    2004-01-01

    Surface tension of molten IF steel containing Ti and contact angle between the liquid steel and solid alumina were measured with sessile droplet method under Ar gas atmosphere at 1500, 1575 and 1600℃. The results show that titanium decreases the surface tension of the molten IF steel and the contact angle. The interfacial tension between the molten IF steel containing Ti and solid alumina decreases with increase in titanium content. The work of adhesion between molten IF steel containing Ti and solid alumina decreases slightly at 1550℃, but increases at 1600℃ with increasing titanium content. It can be deduced that fine bubbles and fine alumina inclusions are easily entrapped in solidifying interface for IF steel containing Ti.

  9. Fine-grained representation learning in convolutional autoencoders

    Science.gov (United States)

    Luo, Chang; Wang, Jie

    2016-03-01

    Convolutional autoencoders (CAEs) have been widely used as unsupervised feature extractors for high-resolution images. As a key component in CAEs, pooling is a biologically inspired operation to achieve scale and shift invariances, and the pooled representation directly affects the CAEs' performance. Fine-grained pooling, which uses small and dense pooling regions, encodes fine-grained visual cues and enhances local characteristics. However, it tends to be sensitive to spatial rearrangements. In most previous works, pooled features were obtained by empirically modulating parameters in CAEs. We see the CAE as a whole and propose a fine-grained representation learning law to extract better fine-grained features. This representation learning law suggests two directions for improvement. First, we probabilistically evaluate the discrimination-invariance tradeoff with fine-grained granularity in the pooled feature maps, and suggest the proper filter scale in the convolutional layer and appropriate whitening parameters in preprocessing step. Second, pooling approaches are combined with the sparsity degree in pooling regions, and we propose the preferable pooling approach. Experimental results on two independent benchmark datasets demonstrate that our representation learning law could guide CAEs to extract better fine-grained features and performs better in multiclass classification task. This paper also provides guidance for selecting appropriate parameters to obtain better fine-grained representation in other convolutional neural networks.

  10. Reliability of fine needle aspiration biopsy in large thyroid nodules.

    Science.gov (United States)

    Bozbıyık, Osman; Öztürk, Şafak; Ünver, Mutlu; Erol, Varlık; Bayol, Ümit; Aydın, Cengiz

    2017-01-01

    Fine needle aspiration biopsy provides one of the most important data that determines the treatment algorithm of thyroid nodules. Nevertheless, the reliability of fine needle aspiration biopsy is controversial in large nodules. The aim of this study was to evaluate the adequacy of fine needle aspiration biopsy in thyroid nodules that are four cm or greater. We retrospectively examined 219 patients files who underwent thyroidectomy for thyroid nodules that were greater than four centimeter between May 2007 and December 2012. Seventy-four patients with hyperthyroidism, and 18 patients without preoperative fine needle aspiration cytology were excluded from the study. Histopathologic results after thyroidectomy were compared with preoperative cytology results, and sensitivity and specificity rates were calculated. False-negativity, sensitivity and specificity rates of fine needle aspiration biopsy of thyroid nodules were found to be 9.7%, 55.5%, and 85%, respectively. Within any nodule of the 127 patients, 28 (22.0%) had thyroid cancer. However, when only nodules of at least 4 cm were evaluated, thyroid cancer was detected in 22 (17.3%) patients. In this study, fine needle aspiration biopsy of large thyroid nodules was found to have a high false-negativity rate. The limitations of fine-needle aspiration biopsy should be taken into consideration in treatment planning of thyroid nodules larger than four centimeters.

  11. Solid electrolytic fuel cell

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, Masayasu; Yamauchi, Yasuhiro; Kamisaka, Mitsuo; Notomi, Kei.

    1989-04-21

    Concerning a solid electrolytic fuel cell with a gas permeable substrate pipe, a fuel electrode installed on this substrate pipe and an air electrode which is laminated on this fuel electrode with the electrolyte in between, the existing fuel cell of this kind uses crystals of CaMnO3, etc. for the material of the air electrode, but its electric resistance is big and in order to avert this, it is necessary to make the film thickness of the air electrode big. However, in such a case, the entry of the air into its inside worsens and the cell performance cannot develop satisfactorily. In view of the above, in order to obtain a high performance solid electrolytic fuel cell which can improve electric conductivity without damaging diffusion rate of the air, this invention proposes with regard to the aforementioned solid electrolytic fuel cell to install a heat resistant and conductive member inside the above air electrode. 6 figs.

  12. Randomized controlled trial of endoscopic ultrasound-guided fine-needle sampling with or without suction for better cytological diagnosis

    DEFF Research Database (Denmark)

    Puri, Rajesh; Vilmann, Peter; Saftoiu, Adrian

    2009-01-01

    two different techniques of EUS-guided sampling of solid masses, using either non-suction or suction with a 10-ml syringe. MATERIAL AND METHODS: Patients assessed during a 6-month period were randomized to three passes of EUS-guided sampling with suction (26 patients) or non-suction (26 patients....... RESULTS: EUS-guided fine-needle sampling with suction of solid masses increased the number of pathology slides (17.8+/-7.1 slides for suction as compared with 10.2+/-5.5 for non-suction, p=0.0001), without increasing the overall bloodiness of each sample. Sensitivity and the negative predictive values...... were higher when suction was applied, as compared to the non-suction group (85.7% as compared with 66.7%, p=0.05). CONCLUSIONS: This prospective randomized study showed that EUS-guided fine-needle sampling of solid masses using suction yields a higher number of slides without increasing bloodiness...

  13. Filtration efficiency validation of glass wool during thermal desorption-gas chromatography-mass spectrometer analysis of fine atmospheric particles.

    Science.gov (United States)

    Hao, Liang; Wu, Dapeng; Ding, Kun; Meng, Hu; Yan, Xiaohui; Guan, Yafeng

    2015-02-06

    Thermal desorption-gas chromatography-mass spectrometer (TD-GC-MS) technique has been widely used for analysis of semi-violate organic compounds on atmospheric aerosol. To prevent GC column from being damaged by fine solid particles during thermal desorption process, glass wool as filter mat is indispensible. However, the filtration efficiency has never been validated. In this paper, the most penetrating particle size and the minimum packing thickness of glass wool were calculated based on classical filtration theory. According to the calculation results, packing parameters of glass wool were optimized experimentally using silica particles. It is demonstrated that glass wool with a packing thickness of 30 mm, solidity of 0.039 can effectively block these fine solid particles from penetrating at normal thermal desorption conditions (T=300°C, u=0.4-4 cm/s). Finally, the filtration efficiency of glass wool was further confirmed with real PM2.5 samples. Under the validated filtration condition, TD-GC-MS was applied for the analysis of non-polar organic compounds on real PM2.5 samples, and very good results were obtained.

  14. Diagnostic utility of endoscopic ultrasound-guided fine-needle aspiration biopsy for glomus tumor of the stomach.

    Science.gov (United States)

    Kato, Shin; Kikuchi, Kaoru; Chinen, Kenji; Murakami, Takahiro; Kunishima, Fumihito

    2015-06-14

    A 52-year-old man was referred for further investigation of a gastric submucosal tumor on the greater curvature of the antrum. Endoscopic ultrasonography demonstrated a hypoechoic solid mass, which was primarily connected to the muscular layer of the stomach. We performed endoscopic ultrasound-guided fine-needle aspiration biopsy. The pathological examination showed proliferation of oval-shaped cells with nest formation, which stained strongly positive for muscle actin, and negative for c-kit, CD34, CD56, desmin, S-100, chromogranin, and neuron-specific enolase. Therefore, we performed laparoscopy and endoscopy cooperative surgery based on the preoperative diagnosis of glomus tumor of the stomach. The final histological diagnosis confirmed the preoperative diagnosis. Although preoperative diagnosis of glomus tumor of the stomach is difficult with conventional images and endoscopic biopsy, endoscopic ultrasound-guided fine-needle aspiration biopsy is an essential tool to gain histological evidence of glomus tumor of the stomach for early diagnosis.

  15. Thin lift dewatering of oil sand tailings: optimizing dewatering of fluid fine tailings by controlling polymer mixing

    Energy Technology Data Exchange (ETDEWEB)

    Demoz, A.; Munoz, V.; Mikula, R. [Natural Resources Canada, CanmetENERGY, Devon, Alberta (Canada)

    2011-07-01

    In the oil sands industry, dewatering of tailings is an important issue. Recent work has shown that the addition of polymer helps to enhance dewatering of fluid fine tailings. High molecular weight polymers are used to bind small solids which results in a higher floc strength with no significant effect on water chemistry. The problem of this technique is that polymers only achieve optimal performance within a narrow window. This paper aimed at assessing the effect of mixing on the dewatering performance of polymer treatment on mature fine tailings. Tests were performed with different impeller types, mixing speeds and durations. Results demonstrated that the flocculation process is critical in the dewatering process and that working at the optimal flocculation conditions presents considerable benefits. This paper investigated the importance of mixing on the dewatering process and highlighted that further work has to be undertaken to optimize this process.

  16. Solid phases of tenoxicam.

    Science.gov (United States)

    Cantera, Rodrigo G; Leza, María G; Bachiller, Carmen M

    2002-10-01

    In this report we describe the preparation and characterization of four polymorphic forms of tenoxicam; they are, three 1:1 stoichiometric solvates with acetonitrile, dioxane, and N,N-dimethylformamide, and an amorphous phase obtained by recrystallization in various solvents. Polymorph IV and solvates with dioxane and N,N-dimethylformamide are reported for the first time in this paper. In addition, three solvates were crystallized in acetone, ethyl acetate, and isopropyl alcohol. These solid forms were characterized by X-ray powder diffraction, differential scanning calorimetry, infrared spectroscopy, thermogravimetry, optical microscopy, and elemental analysis. Solid-state properties, intrinsic dissolution rate, and dissolution kinetics from formulated tablets are also provided.

  17. Photochemistry on solid surfaces

    CERN Document Server

    Matsuura, T

    1989-01-01

    The latest developments in photochemistry on solid surfaces, i.e. photochemistry in heterogeneous systems, including liquid crystallines, are brought together for the first time in a single volume. Distinguished photochemists from various fields have contributed to the book which covers a number of important applications: molecular photo-devices for super-memory, photochemical vapor deposition to produce thin-layered electronic semiconducting materials, sensitive optical media, the control of photochemical reactions pathways, etc. Photochemistry on solid surfaces is now a major field and this

  18. Optical properties of solids

    CERN Document Server

    Wooten, Frederick

    1972-01-01

    Optical Properties of Solids covers the important concepts of intrinsic optical properties and photoelectric emission. The book starts by providing an introduction to the fundamental optical spectra of solids. The text then discusses Maxwell's equations and the dielectric function; absorption and dispersion; and the theory of free-electron metals. The quantum mechanical theory of direct and indirect transitions between bands; the applications of dispersion relations; and the derivation of an expression for the dielectric function in the self-consistent field approximation are also encompassed.

  19. Solid-state circuits

    CERN Document Server

    Pridham, G J

    2013-01-01

    Solid-State Circuits provides an introduction to the theory and practice underlying solid-state circuits, laying particular emphasis on field effect transistors and integrated circuits. Topics range from construction and characteristics of semiconductor devices to rectification and power supplies, low-frequency amplifiers, sine- and square-wave oscillators, and high-frequency effects and circuits. Black-box equivalent circuits of bipolar transistors, physical equivalent circuits of bipolar transistors, and equivalent circuits of field effect transistors are also covered. This volume is divided

  20. Solid state theory

    CERN Document Server

    Harrison, Walter A

    2011-01-01

    ""A well-written text . . . should find a wide readership, especially among graduate students."" - Dr. J. I. Pankove, RCA.The field of solid state theory, including crystallography, semi-conductor physics, and various applications in chemistry and electrical engineering, is highly relevant to many areas of modern science and industry. Professor Harrison's well-known text offers an excellent one-year graduate course in this active and important area of research. While presenting a broad overview of the fundamental concepts and methods of solid state physics, including the basic quantum theory o

  1. Hybrid elastic solids

    KAUST Repository

    Lai, Yun

    2011-06-26

    Metamaterials can exhibit electromagnetic and elastic characteristics beyond those found in nature. In this work, we present a design of elastic metamaterial that exhibits multiple resonances in its building blocks. Band structure calculations show two negative dispersion bands, of which one supports only compressional waves and thereby blurs the distinction between a fluid and a solid over a finite frequency regime, whereas the other displays super anisotropy-in which compressional waves and shear waves can propagate only along different directions. Such unusual characteristics, well explained by the effective medium theory, have no comparable analogue in conventional solids and may lead to novel applications. © 2011 Macmillan Publishers Limited. All rights reserved.

  2. Proton tunneling in solids

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, J.

    1998-10-01

    The tunneling rate of the proton and its isotopes between interstitial sites in solids is studied theoretically. The phonons and/or the electrons in the solid have two effects on the tunneling phenomenon. First, they suppress the transfer integral between two neighbouring states. Second, they give rise to a finite lifetime of the proton state. Usually the second effect is large and the tunneling probability per unit time (tunneling rate) can be defined. In some cases, however, a coherent tunneling is expected and actually observed. (author)

  3. Local Solid Shape

    Directory of Open Access Journals (Sweden)

    Jan Koenderink

    2015-10-01

    Full Text Available Local solid shape applies to the surface curvature of small surface patches—essentially regions of approximately constant curvatures—of volumetric objects that are smooth volumetric regions in Euclidean 3-space. This should be distinguished from local shape in pictorial space. The difference is categorical. Although local solid shape has naturally been explored in haptics, results in vision are not forthcoming. We describe a simple experiment in which observers judge shape quality and magnitude of cinematographic presentations. Without prior training, observers readily use continuous shape index and Casorati curvature scales with reasonable resolution.

  4. Solid State Research

    Science.gov (United States)

    2010-08-26

    width at half-maximum measured at 4 K of GalnAsSb layers grown on GaSb substrates. Solid circles this work; open squares from [9]; open triangle from...Rowe N. R. Newbury A. Sanchez-Rubio C. A. Primmerman Bermuda Grass Smut Spores WhitET 0 12 3 4 5 6 Ratio (PMT1 / PMT2) Figure 1-4...measured at 4 K of GalnAsSb layers grown on GaSb sub- strates. Solid circles this work; open squares from [9]; open triangle from [10]. [9],[10

  5. Reactions at Solid Surfaces

    CERN Document Server

    Ertl, Gerhard

    2009-01-01

    Expanding on the ideas first presented in Gerhard Ertl's acclaimed Baker Lectures at Cornell University, Reactions at Solid Surfaces comprises an authoritative, self-contained, book-length introduction to surface reactions for both professional chemists and students alike. Outlining our present understanding of the fundamental processes underlying reactions at solid surfaces, the book provides the reader with a complete view of how chemistry works at surfaces, and how to understand and probe the dynamics of surface reactions. Comparing traditional surface probes with more modern ones, and brin

  6. SolidWorks : opetuspaketti

    OpenAIRE

    Myllymäki, Vesa

    2011-01-01

    Opinnäytetyössä tutkittiin mahdollisuuksia tehdä opetusvideoita SolidWorks -ohjelman käyttämisestä. Tähän tarkoitukseen löydettiin menetelmään sopiva ohjelma, CamStudio, jota sitten sovellettiin käytännössä. Camstudio ja SolidWorks ohjelmia hyödyntäen luotiin videoita kolmiulotteisista mallinnusprosesseista. Menetelmä toimi, mutta sen käyttökelpoisuuteen liittyi ongelmia. Videoden laatu on heikko, mutta sen parantaminen merkitsisi suurempaa tiedostokokoa, mikä voi tuottaa tietokantaongelmia. ...

  7. Rheo-diecasting Process for Semi-solid Aluminum Alloys

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A novel one-step semisolid processing technique, the rheo-diecasting (RDC) process, was developed, which adapts in situ creation of semisolid metal slurry with fine and spherical solid particles followed by direct shaping of the slurry into a near-net shape component using the existing cold chamber diecasting process. The RDC process was applied to process A356 and A380 aluminum alloys. The resulting microstructures and mechanical properties of RDC products under as-cast and various heat treatment conditions were analyzed. The experimental results show that the RDC samples have an extremely low porosity, a fine and uniform microstructure throughout entire casting, and consequently much improved strength and ductility in the as-cast condition. The strength of RDC A356 alloy can be substantially improved under T5 and T6 heat treatments without loss of ductility.

  8. Fine-Structured Plasma Flows in Prominences

    Science.gov (United States)

    Panasenco, O.; Velli, M.; Landi, S.

    2008-12-01

    Plasmas in prominences (filaments against the disk) exhibit a very wide spectrum of different kind of motions. Here we analyze the plasma motions inside prominences observed by Hinode/SOT during 2006-2007 with focus on two spectacular examples from 25 April 2007 in Halpha line and 30 November 2006 in CaH line and then carry out some simulations of the possible dynamics. Most filaments are composed of fine threads of similar dimensions rooted in the chromosphere/photosphere. Recent observations of counter-streaming motions together with oscillations along the threads provide strong evidence that the threads are field aligned. To more correctly interpret the nature of observed downward flows of dense and cool plasma as well as the upward dark flows of less dense plasma, we take into account the geometry of the prominence structures and the viewing angle. The dark upflows exhibit turbulent patterns such as vortex formation and shedding that are consistent with the motions predicted by instabilities of the interchange type. Sometimes an appearance of dark motions is generated by dark voids opened in the prominence sheet after initiation of nearby downflow streams, implying mass drainage in the downflows. Based on 304 A observations, there is more filament mass in prominences than is visible in either the Halpha or CaH lines. The source of the downward moving plasma may be located either higher above the visible upper edge of the prominence or on the far end of the prominence spine. The bright downward motions of the more cool and dense plasma may be partly due to the counter-streaming motion along the magnetic fields lines and also to the presence of Rayleigh-Taylor type or ballooning/interchange instabilities in the upper regions of the prominence. Transverse motions of filament threads caused by magnetic instabilities constantly provide the conditions for reconnection in the low part of the corona and the chromosphere. We suggest that the combination of flows along

  9. Electromyography of Swallowing with Fine Wire Intramuscular Electrodes in Healthy Human: Amplitude Difference of Selected Hyoid Muscles.

    Science.gov (United States)

    Inokuchi, Haruhi; González-Fernández, Marlís; Matsuo, Koichiro; Brodsky, Martin B; Yoda, Mitsumasa; Taniguchi, Hiroshige; Okazaki, Hideto; Hiraoka, Takashi; Palmer, Jeffrey B

    2016-02-01

    Few studies have examined the intensity of muscle activity during swallowing in healthy humans. We examined selected hyoid muscles using fine wire intramuscular electromyography (EMG) during swallowing of four food consistencies. Thirteen healthy adults were studied using videofluorography and EMG of the anterior belly of digastric (ABD), geniohyoid (GH), sternohyoid (SH), and masseter (MA; surface electrodes) while ingesting thin liquid (three trials) and solid food of three consistencies (banana, tofu, and cookie, three trials each). After rectification, integration, and normalization, peak EMG amplitudes for each muscle in each trial were measured. Hyoid displacements were measured in two dimensions. Data were analyzed using repeated measures ANOVA with Bonferroni correction. GH had the highest adjusted amplitude for both solids and liquid. For MA and ABD, amplitude was highest with triturated cookie. For ABD, amplitude was lowest with liquid. There were no significant food consistency effects for GH or SH. Hyoid displacements were greatest for cookie and the lowest for liquid. EMG amplitude varied with initial food consistency. The high peak EMG amplitude of GH is consistent with its essential role in opening the upper esophageal sphincter. High MA amplitude with hard solid foods is likely due to the higher tongue-palate pressure with triturated solids. The higher ABD amplitude with solid food is associated with greater hyoid displacement. These findings support the existence of a central pattern generator that modifies the level of muscle activity during pharyngeal swallowing in response to input from mechanoreceptors in the oral cavity.

  10. Solid state physics

    CERN Document Server

    Brewster, Hilary D

    2009-01-01

    Solid state physics is an exhaustive introductory text for the students of physics. Keeping in mind, this book has been prepared to present the subject-matter in an easily understandable way without sacrificing the essential details and principles an yet avoiding redundant matter and unnecessary complications. This book is expected to meet adequately the need of the students for whom it is meant.

  11. Solid Oxide Fuel Cell

    DEFF Research Database (Denmark)

    2010-01-01

    The solid oxide fuel cell comprising a metallic support material, an active anode layer consisting of a good hydrocarbon cracking catalyst, an electrolyte layer, an active cathode layer, and a transition layer consisting of preferably a mixture of LSM and a ferrite to the cathode current collector...

  12. Current Solid Mechanics Research

    DEFF Research Database (Denmark)

    Tvergaard, Viggo

    2016-01-01

    About thirty years ago James Lighthill wrote an essay on “What is Mechanics?” With that he also included some examples of the applications of mechanics. While his emphasis was on fluid mechanics, his own research area, he also included examples from research activities in solid mechanics....

  13. Solid-phase microextraction

    DEFF Research Database (Denmark)

    Nilsson, Torben

    The objective of this study has been to develop new analytical methods using the rapid, simple and solvent-free extraction technique solid-phase microextraction (SPME) for the quantitative analysis of organic pollutants at trace level in drinking water and environmental samples. The dynamics...

  14. Local solid shape

    NARCIS (Netherlands)

    Koenderink, Jan|info:eu-repo/dai/nl/070864543; van Doorn, A.J.; Wagemans, Johan

    2015-01-01

    Local solid shape applies to the surface curvature of small surface patches-essentially regions of approximately constant curvatures-of volumetric objects that are smooth volumetric regions in Euclidean 3-space. This should be distinguished from local shape in pictorial space. The difference is cate

  15. Solid-State Devices.

    Science.gov (United States)

    Sutliff, Ronald D.; And Others

    This self-study course is designed to familiarize Marine Corps enlisted personnel with the principles of solid-state devices and their functions. The course contains four study units. Each study unit begins with a general objective, which is a statement of what the student should learn from the unit. The study units are divided into numbered work…

  16. Solid Oxide Fuel Cell

    DEFF Research Database (Denmark)

    2010-01-01

    The solid oxide fuel cell comprising a metallic support material, an active anode layer consisting of a good hydrocarbon cracking catalyst, an electrolyte layer, an active cathode layer, and a transition layer consisting of preferably a mixture of LSM and a ferrite to the cathode current collector...

  17. Solid-Waste Management

    Science.gov (United States)

    Science Teacher, 1973

    1973-01-01

    Consists of excerpts from a forthcoming publication of the United States Environmental Protection Agency, Student's Guide to Solid-Waste Management.'' Discusses the sources of wastes from farms, mines, factories, and communities, the job of governments, ways to collect trash, methods of disposal, processing, and suggests possible student action.…

  18. Physical properties of solids

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, M. K.; Young, Jr, F. W.

    1977-10-01

    Research at ORNL into the physical properties of solids is described. Topics covered include: optical, electrical, and magnetic properties of magnesium oxide; ionic conductivity and superconductivity; surface physics and catalysis; defects and impurities in insulating crystals; photovoltaic conversion of solar energy; and fracture studies. (GHT)

  19. Resolving and Controlling Photoinduced Ultrafast Solvation in the Solid State.

    Science.gov (United States)

    Delor, Milan; McCarthy, Dannielle G; Cotts, Benjamin L; Roberts, Trevor D; Noriega, Rodrigo; Devore, David D; Mukhopadhyay, Sukrit; De Vries, Timothy S; Ginsberg, Naomi S

    2017-09-07

    Solid-state solvation (SSS) is a solid-state analogue of solvent-solute interactions in the liquid state. Although it could enable exceptionally fine control over the energetic properties of solid-state devices, its molecular mechanisms have remained largely unexplored. We use ultrafast transient absorption and optical Kerr effect spectroscopies to independently track and correlate both the excited-state dynamics of an organic emitter and the polarization anisotropy relaxation of a small polar dopant embedded in an amorphous polystyrene matrix. The results demonstrate that the dopants are able to rotationally reorient on ultrafast time scales following light-induced changes in the electronic configuration of the emitter, minimizing the system energy. The solid-state dopant-emitter dynamics are intrinsically analogous to liquid-state solvent-solute interactions. In addition, tuning the dopant/polymer pore ratio offers control over solvation dynamics by exploiting molecular-scale confinement of the dopants by the polymer matrix. Our findings will enable refined strategies for tuning optoelectronic material properties using SSS and offer new strategies to investigate mobility and disorder in heterogeneous solid and glassy materials.

  20. Application of ultra-flocculation for improving fine coal concentrate dewatering

    Energy Technology Data Exchange (ETDEWEB)

    N.N. Rulyov; B.Y. Korolyov; N.M. Kovalchuk [Ukrainian National Academy of Sciences, Kiev (Ukraine). Institute of Biocolloid Chemistry

    2006-01-15

    The possibility of significant improvements in vacuum filtration of fine coal suspensions through the application of ultra-flocculation was studied. It was shown theoretically that even when present in quantities of a few percent, the ultrafine particles (<10 microns) highly contributed to the hydraulic resistance of the filter cake. The experiments showed that short-term hydrodynamic treatment of the coal suspension at relatively high medium velocity gradients (750 s{sup -1}) performed immediately upon the introduction of the flocculant resulted in significant improvements in the filtration process due to the effect of specifically binding the finest particles. This treatment decreased the hydraulic resistance of the cake on the screen vacuum filter by roughly 1.6 times, decreased the solids content in the filtrate by 4 times and decreased the flocculant consumption by 2 times.

  1. Fine structures in Fe3Al alloy layer of a new hot dip aluminized steel

    Indian Academy of Sciences (India)

    Li Yajiang; Wang Juan; Zhang Yonglan; X Holly

    2002-12-01

    The fine structure in the Fe–Al alloy layer of a new hot dip aluminized steel (HDA) was examined by means of X-ray diffractometry (XRD), electron diffraction technique, etc. The test results indicated that the Fe–Al alloy layer of the new aluminized steel mainly composed of Fe3Al, FeAl and -Fe (Al) solid solution. There was no brittle phase containing higher aluminum content, such as FeAl3 (59.18% Al) and Fe2Al7 (62.93% Al). The tiny cracks and embrittlement, formerly caused by these brittle phases in the conventional aluminum-coated steel, were effectively eliminated. There was no microscopic defect (such as tiny cracks, pores or loose layer) in the coating. This is favourable to resist high temperature oxidation and corrosion of the aluminized steel.

  2. THE INFLUENCE OF CATIONIZED BIRCH XYLAN ON WET AND DRY STRENGTH OF FINE PAPER

    Directory of Open Access Journals (Sweden)

    Janne Kataja-aho,

    2012-02-01

    Full Text Available Cationized birch xylan was prepared and its use as a papermaking chemical was evaluated. The focus was on studying the effects of cationized birch xylan on the wet and dry strength of fine paper. The results of the laboratory experiments show that the addition of 3 percent of cationized birch xylan to birch kraft pulp improved the initial wet strength of the web by 30 percent compared to base stock at a solids content of 55%. Furthermore, the tensile stiffness of the wet web increased by approximately a third and the dry tensile strength improved by 26%, while the dry elastic modulus was not changed. The improvements in the strength properties were clear when compared to the base stock, but not as high as achieved with conventionally used cationized starch. The difference between the xylan and starch is most likely due to the shorter polymer chain length of the cationized xylan.

  3. Phase-field simulation of formation of cellular dendrites and fine cellular structures at high growth velocities during directional solidification of Ti56Al44 alloy

    Institute of Scientific and Technical Information of China (English)

    LI Xin-zhong; GUO Jing-jie; SU Yan-qing; WU Shi-ping; FU Heng-zhi

    2005-01-01

    A phase-field model whose free energy of the solidification system derived from the Calphad thermodynamic modeling of phase diagram was used to simulate formation of cellular dendrites and fine cellular structures of Ti56Al44 alloy during directional solidification at high growth velocities. The liquid-solid phase transition of L→β was chosen. The dynamics of breakdown of initially planar interfaces into cellular dendrites and fine cellular structures were shown firstly at two growth velocities. Then the unidirectional free growths of two initial nucleations evolving to fine cellular dendrites were investigated. The tip splitting phenomenon is observed and the negative temperature gradient in the liquid represents its supercooling directional solidification. The simulation results show the realistic evolution of interfaces and microstructures and they agree with experimental one.

  4. Block-to-Point Fine Registration in Terrestrial Laser Scanning

    Directory of Open Access Journals (Sweden)

    Jin Wang

    2013-12-01

    Full Text Available Fine registration of point clouds plays an important role in data analysis in Terrestrial Laser Scanning (TLS. This work proposes a block-to-point fine registration approach to correct the errors of point clouds from TLS and of geodetic networks observed using total stations. Based on a reference coordinate system, the block-to-point estimation is performed to obtain representative points. Then, fine registration with a six-parameter transformation is performed with the help of an Iterative Closest Point (ICP method. For comparisons, fine registration with a seven-parameter transformation is introduced by applying a Singular Value Decomposition (SVD algorithm. The proposed method not only corrects the registration errors between a geodetic network and the scans, but also considers the errors among the scans. The proposed method was tested on real TLS data of a dam surface, and the results showed that distance discrepancies of estimated representative points between scans were reduced by approximately 60%.

  5. Fine Particle Matter (PM2.5) Design Value

    Data.gov (United States)

    U.S. Environmental Protection Agency — Fine particulate matter or PM2.5 (total mass of particles below 2.5 micron is diameter) is known to cause adverse health effects in humans.See the following websites...

  6. Study on conglutination model for fine moist material during screening

    Institute of Scientific and Technical Information of China (English)

    陈惜明; 邓凡政; 赵跃民; 朱红; 高庆宇

    2002-01-01

    All coal preparation in which fine coal is handled depends to some extent on the wettability of coal surface by water. The content of external water in fine moist material plays significant role on screening. This article probed into the causations why fine moist materials adhere to the screen deck on common vibrator in the process of screening. Although the wetting that results from interactions between the coal surface and water molecules that are determined by the composition of coal matrix (interrelated with coal rank) and heterogeneous constituents such as oxygen function groups, mineral impurities and pores have something to do with adhering, we found that the effect of wettability is not the key causation to agglomeration, in other words, water bridges among particles are the key causation to the fine moist materials adhesion. This paper also shows how the capillary adhesive forces forms and how to calculate and measure these forces.

  7. Advanced Portable Fine Water Mist Fire Extinguisher for Spacecraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fine water mist (FWM) is a promising replacement technology for fire suppression on the next generation of manned spacecraft. It offers advantages in performance,...

  8. Fine Water Mist Fire Extinguisher for Spacecraft Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This three phase SBIR project from ADA Technologies Inc. (ADA) builds upon the experience of ADA in development of fine water mist (FWM) fire suppression technology....

  9. Fine 5 segab vett, liiva ja videot / Tiit Tuumalu

    Index Scriptorium Estoniae

    Tuumalu, Tiit, 1971-

    2000-01-01

    Tantsutrupi Five 5 lavastustest (trupp tegutseb 1992. a., on väja kasvanud tantsuteatrist Nordic Star), ka 1992. a. Fine 5 juurde loodud stuudio-koolist, kus on võimalik õppida modern- ja nüüdistantsu

  10. Fine 5 segab vett, liiva ja videot / Tiit Tuumalu

    Index Scriptorium Estoniae

    Tuumalu, Tiit, 1971-

    2000-01-01

    Tantsutrupi Five 5 lavastustest (trupp tegutseb 1992. a., on väja kasvanud tantsuteatrist Nordic Star), ka 1992. a. Fine 5 juurde loodud stuudio-koolist, kus on võimalik õppida modern- ja nüüdistantsu

  11. Fine Structure of Solar Acoustic Oscillations Due to Rotation

    Science.gov (United States)

    Goode, P. R.; Dziembowski, W.

    1984-01-01

    The nature of the fine structure of high order, low degree five minute period solar oscillations following from various postulated forms of spherical rotation is predicted. The first and second order effects of rotation are included.

  12. Fine 5 tantsib Bachi järgi

    Index Scriptorium Estoniae

    2016-01-01

    Tantsuteater Fine 5 toob lavale lavastuse "HTK ehk hästi treenitud klaviir". Teos on loodud J.S. Bachi "Hästitempereeritud klaviiri" (HTK) esimese osa muusikale. Koreograafid Tiina Ollesk ja Renee Nõmmik

  13. Fluidization of fine powders cohesive versus dynamical aggregation

    CERN Document Server

    Valverde Millán, José Manuel

    2012-01-01

    This book illustrates the rich phenomenology exhibited by fine powders when fluidized by a gas flow, describing novel processes to assist fluidization by helping the gas flow to mobilize and break cohesive aggregates, which help to homogenize fluidization.

  14. performance of concrete with partial replacement of fine aggregates ...

    African Journals Online (AJOL)

    user

    Key Words: compressive strength, concrete, crushed waste glass, flexural strength, setting time, water absorption and workability. ... powder as partial replacement of fine aggregates up to ... water in cement paste and reactive silica in the WG.

  15. Fine 5 tantsib Bachi järgi

    Index Scriptorium Estoniae

    2016-01-01

    Tantsuteater Fine 5 toob lavale lavastuse "HTK ehk hästi treenitud klaviir". Teos on loodud J.S. Bachi "Hästitempereeritud klaviiri" (HTK) esimese osa muusikale. Koreograafid Tiina Ollesk ja Renee Nõmmik

  16. Process for preparing fine grain silicon carbide powder

    Science.gov (United States)

    Wei, G.C.

    Method of producing fine-grain silicon carbide powder comprises combining methyltrimethoxysilane with a solution of phenolic resin, acetone and water or sugar and water, gelling the resulting mixture, and then drying and heating the obtained gel.

  17. Potential causes for obtaining non-diagnostic results from fine needle aspiration biopsy of thyroid nodules.

    Science.gov (United States)

    Özel, Deniz; Özel, Betül Duran; Özkan, Fuat

    2016-06-01

    The aim of this prospective study was to evaluate factors that could affect the diagnostic result success ratio of fine needle aspiration biopsy of thyroid nodules. 664 patients and 696 nodules were included in this study. Demographic features of age and gender and nodule features of macrocalcification (MC) and internal content (cystic or solid predominance) were evaluated. All biopsies were performed from 1 cm or larger nodules. Three different size needles were used for comparison (22, 23 and 25 G). The patients in each group had a similar number of nodules with MC, and cystic predominance to obtain comparable results. All procedures were performed by the same radiologist, who had 4 years of experience. Histologically adequate material criteria were identified. All pathological specimens were evaluated as diagnostic or non-diagnostic by the same pathology technician. Chi-square, student's t test and univariate analysis were used for statistical analysis. There were no statistically significant differences in demographic features and nodule properties from diagnostic results of fine needle aspiration biopsy of thyroid nodules. On the other hand, 23 G needles offered a better potential for obtaining adequate samples with a statistically significant difference. Obtaining adequate material in fine needle aspiration biopsy from thyroid nodules is a challenging issue and the results are controversial. Since we obtained the best ratio with 23 G needles, we recommend interventional radiologists to use 23 G needles as far as possible and not to consider needles thicker needles than 22 G or thinner than 25 G. Nodule features and demographic features did not have an effect on obtaining adequate cytological material.

  18. Luminescence and the solid state

    CERN Document Server

    Ropp, Richard C

    2013-01-01

    Since the discovery of the transistor in 1948, the study of the solid state has been burgeoning. Recently, cold fusion and the ceramic superconductor have given cause for excitement. There are two approaches possible to this area of science, namely, that of solid state physics and solid state chemistry, although both overlap extensively. The former is more concerned with electronic states in solids (including electromagnetics) whereas the latter is more concerned with interactions of atoms in solids. The area of solid state physics is well documented, however, there are very few texts which de

  19. M-Solidity Testing Systems

    Institute of Scientific and Technical Information of China (English)

    K. Denecke; S.L. Wismath

    2002-01-01

    A set S of hypersubstitutions is called an M-solidity testing system for a class of varieties if it is possible to determine all M-solid varieties in the class using only the hypersubstitutions from S. If S is a minimal such set, we will call it an M-solidity basis for the class. In this paper, we relate solidity testing systems to the Galois connection between hypersubstitutions and varieties, and present a number of examples of solidity testing systems for several different types of varieties, including examples of the existence of finite M-solidity bases for various classes.

  20. SolidWorks Administration Bible

    CERN Document Server

    Lombard, Matt

    2009-01-01

    What you need to prepare, install, and maintain SolidWorks. It's not enough to know how to use SolidWorks, if your job also requires you to install or maintain it, train new users, and implement standards. This in-depth guide was written for those of you who have to actually manage your company's SolidWorks system. From hardware selection to helping users to licensing and more, this is the everyday, bread-and-butter SolidWorks administration resource that IT and CAD managers have been seeking.:; SolidWorks is a powerful 3D solid modeling system that is popular with CAD users everywhere, but of

  1. Spatial variability of fine particles in Parisian streets

    OpenAIRE

    Duché, Sarah; Beltrando, Gérard

    2012-01-01

    International audience; To study the spatial variability of airborne particles and to evaluate the personal and tourist exposure to fine particles in Paris, measurements of fine particles (PM2.5) concentrations have been made in Parisian streets in different mode of transport (bus, bike and walking), using a portable sensor. We use also meteorological parameters sensor (temperature,humidity and wind speed), a camera to view traffic and a GPS to compare with particles levels. PM2.5 levels are ...

  2. A FINE GRANULAR JOINT SOURCE CHANNEL CODING METHOD

    Institute of Scientific and Technical Information of China (English)

    Zhuo Li; Shen Lansun; Zhu Qing

    2003-01-01

    An improved FGS (Fine Granular Scalability) coding method is proposed in this letter, which is based on human visual characteristics. This method adjusts FGS coding frame rate according to the evaluation of video sequences so as to improve the coding efficiency and subject perceived quality of reconstructed images. Finally, a fine granular joint source channel coding is proposed based on the source coding method, which not only utilizes the network resources efficiently, but guarantees the reliable transmission of video information.

  3. Global Talent on Exhibit at Fine Arts Design Festival

    Institute of Scientific and Technical Information of China (English)

    Susan

    2003-01-01

    Rising young designers from around the worid revealed the creative trends in their field at the """"""""New Resource 2002 Design Festival,"""""""" held this fall by the Central Academy of Fine Arts {CAFA) in Beijing, With the theme of """"""""artistic design with new resources in the global economy and multicultural era"""""""", the event attracted over 50 academies and colleges of fine arts both home and abroad,

  4. Tree species richness affecting fine root biomass in European forests

    Science.gov (United States)

    Finér, Leena; Domisch, Timo; Vesterdal, Lars; Dawud, Seid M.; Raulund-Rasmussen, Karsten

    2016-04-01

    Fine roots are an important factor in the forest carbon cycle, contributing significantly to below-ground biomass and soil carbon storage. Therefore it is essential to understand the role of the forest structure, indicated by tree species diversity in controlling below-ground biomass and managing the carbon pools of forest soils. We studied how tree species richness would affect fine root biomass and its distribution in the soil profile and biomass above- and below-ground allocation patterns of different tree species. Our main hypothesis was that increasing tree species richness would lead to below-ground niche differentiation and more efficient soil exploitation by the roots, resulting in a higher fine root biomass in the soil. We sampled fine roots of trees and understorey vegetation in six European forest types in Finland, Poland, Germany, Romania, Italy and Spain, representing boreal, temperate and Mediterranean forests, established within the FunDivEUROPE project for studying the effects of tree species diversity on forest functioning. After determining fine root biomasses, we identified the percentages of different tree species in the fine root samples using the near infrared reflectance spectroscopy (NIRS) method. Opposite to our hypothesis we did not find any general positive relationship between tree species richness and fine root biomass. A weak positive response found in Italy and Spain seemed to be related to dry environmental conditions during Mediterranean summers. At the Polish site where we could sample deeper soil layers (down to 40 cm), we found more tree fine roots in the deeper layers under species-rich forests, as compared to the monocultures, indicating the ability of trees to explore more resources and to increase soil carbon stocks. Tree species richness did not affect biomass allocation patterns between above- and below-ground parts of the trees.

  5. Fluidized reduction of oxides on fine metal powders without sintering

    Science.gov (United States)

    Hayashi, T.

    1985-01-01

    In the process of reducing extremely fine metal particles (av. particle size or = 1000 angstroms) covered with an oxide layer, the metal particles are fluidized by a gas flow contg. H, heated, and reduced. The method uniformly and easily reduces surface oxide layers of the extremely fine metal particles without causing sintering. The metal particles are useful for magnetic recording materials, conductive paste, powder metallurgy materials, chem. reagents, and catalysts.

  6. Anodic aluminum oxide with fine pore size control for selective and effective particulate matter filtering

    Science.gov (United States)

    Zhang, Su; Wang, Yang; Tan, Yingling; Zhu, Jianfeng; Liu, Kai; Zhu, Jia

    2016-07-01

    Air pollution is widely considered as one of the most pressing environmental health issues. Particularly, atmospheric particulate matters (PM), a complex mixture of solid or liquid matter suspended in the atmosphere, are a harmful form of air pollution due to its ability to penetrate deep into the lungs and blood streams, causing permanent damages such as DNA mutations and premature death. Therefore, porous materials which can effectively filter out particulate matters are highly desirable. Here, for the first time, we demonstrate that anodic aluminum oxide with fine pore size control fabricated through a scalable process can serve as effective and selective filtering materials for different types of particulate matters (such as PM2.5, PM10). Combining selective and dramatic filtering effect, fine pore size control and a scalable process, this type of anodic aluminum oxide templates can potentially serve as a novel selective filter for different kinds of particulate matters, and a promising and complementary solution to tackle this serious environmental issue.

  7. Enzymatic hydrolysis of anchovy fine powder at high and ambient pressure, and characterization of the hydrolyzates.

    Science.gov (United States)

    Kim, Namsoo; Son, So-Hee; Maeng, Jin-Soo; Cho, Yong-Jin; Kim, Chong-Tai

    2016-02-01

    At specific conditions of high pressure, the stability and activity of some enzymes are reportedly known to increase. The aim of this study was to apply pressure-tolerant proteases to hydrolyzing anchovy fine powder (AFP) and to determine product characteristics of the resultant hydrolyzates. Anchovy fine powder enzyme hydrolyzates (AFPEHs) were produced at 300 MPa and ambient pressure using combinations of Flavourzyme 500MG, Alcalase 2.4L, Marugoto E and Protamex. When the same protease combination was used for hydrolysis, the contents of total soluble solids, total water-soluble nitrogen and trichloroacetic acid-soluble nitrogen in the AFPEHs produced at 300 MPa were conspicuously higher than those in the AFPEHs produced at ambient pressure. This result and electrophoretic characteristics indicated that the high-pressure process of this study accelerates protein hydrolysis compared with the ambient-pressure counterpart. Most peptides in the hydrolyzates obtained at 300 MPa had molecular masses less than 5 kDa. Functionality, sensory characteristics and the content of total free amino acids of selected hydrolyzates were also determined. The high-pressure hydrolytic process utilizing pressure-tolerant proteases was found to be an efficient method for producing protein hydrolyzates with good product characteristics. © 2015 Society of Chemical Industry.

  8. Optimize Operating Conditions on Fine Particle Grinding Process with Vertically Stirred Media Mill

    Science.gov (United States)

    Yang, Yang; Rowson, Neil; Ingram, Andy

    2016-11-01

    Stirred media mill recently is commonly utilized among mining process due to its high stressing intensity and efficiency. However, the relationship between size reduction and flow pattern within the mixing pot is still not fully understand. Thus, this work investigates fine particle grinding process within vertically stirred media mills by altering stirrer geometry, tip speed and solids loading. Positron Emitting Particle Tracking (PEPT) technology is utilized to plot routine of particles velocity map. By tacking trajectory of a single particle movement within the mixing vessel, the overall flow pattern is possible to be plotted. Ground calcium carbonate, a main product of Imerys, is chosen as feeding material (feed size D80 30um) mixed with water to form high viscous suspension. To obtain fine size product (normally D80 approximately 2um), large amount of energy is drawn by grinding mill to break particles through impact, shear attrition or compression or a combination of them. The results indicate higher energy efficient is obtained with more dilute suspension. The optimized stirrer proves more energy-saving performance by altering the slurry circulate. Imerys Minerals Limited.

  9. Hydrogen Isotopic Composition of Water in the Martian Atmosphere and Released from Rocknest Fines

    Science.gov (United States)

    Leshin, L. A.; Webster, C. R.; Mahaffy, P. R.; Flesh, G. J.; Christensen, L. E.; Stern, J. C.; Franz, H. B.; McAdam, A. C.; Niles, P. B.; Archer, P. B., Jr.; Sutter, B.; Jones, J. H.; Ming, D. W.; Atreya, S. K.; Owen, T. C.; Conrad, P.

    2013-01-01

    The Mars Science Laboratory Curiosity rover sampled the aeolian bedform called Rocknest as its first solid samples to be analyzed by the analytical instruments CheMin and SAM. The instruments ingested aliquots from a sieved sample of less than 150 micrometer grains. As discussed in other reports at this conference [e.g., 1], CheMin discovered many crystalline phases, almost all of which are igneous minerals, plus some 10s of percent of x-ray amorphous material. The SAM instrument is focused on understanding volatiles and possible organics in the fines, performing evolved gas analysis (EGA) with the SAM quadrapole mass spectrometer (QMS), isotope measurements using both the QMS and the tunable laser spectrometer (TLS), which is sensitive to CO2, water and methane, and organics with the gas chromatograph mass spectrometer (GCMS). As discussed in the abstract by Franz et al. [2] and others, EGA of Rocknest fines revealed the presence of significant amounts of H2O as well as O-, C- and S-bearing materials. SAM has also tasted the martian atmosphere several times, analyzing the volatiles in both the TLS and QMS [e.g., 3,4]. This abstract will focus on presentation of initial hydrogen isotopic data from the TLS for Rocknest soils and the atmosphere, and their interpretation. Data for CO2 isotopes and O isotopes in water are still being reduced, but should be available by at the conference.

  10. Finely tuning MOFs towards high-performance post-combustion CO2 capture materials.

    Science.gov (United States)

    Wang, Qian; Bai, Junfeng; Lu, Zhiyong; Pan, Yi; You, Xiaozeng

    2016-01-11

    CO2 capture science and technology, particularly for the post-combustion CO2 capture, has become one of very important research fields, due to great concern of global warming. Metal-organic frameworks (MOFs) with a unique feature of structural fine-tunability, unlike the traditional porous solid materials, can provide many and powerful platforms to explore high-performance adsorbents for post-combustion CO2 capture. Until now, several strategies for finely tuning MOF structures have been developed, in which either the larger quadrupole moment and polarizability of CO2 are considered: metal ion change (I), functional groups attachment (II) and functional group insertion (III), vary the electronic nature of the pore surface; or targeting the smaller kinetic diameter of CO2 over N2 is focused on: framework interpenetration (IV), ligand shortening (V) and coordination site shifting (VI) contract the pore size of frameworks to improve their CO2 capture properties. In this review, from the viewpoint of synthetic materials scientists/chemists, we would like to introduce and summarize these strategies based upon recent work published by other groups and ourselves.

  11. On the location of acid-hydrolysable carbon in lunar soil fines

    Science.gov (United States)

    Fallick, A. E.; Wright, I. P.; Pillinger, C. T.; Stephenson, A.; Morris, R. V.

    1982-01-01

    Soil fines exposed on the lunar surface accumulate small metallic iron particles and solar wind-derived carbon. In previous work, it has been suggested that an intimate association exists between one particular carbon phase, hydrolysable carbon, and very fine iron droplets, where the carbon is in solid solution in the iron. The earlier hypothesis of a constant carbon in iron concentration across a broad range of droplet sizes is testable by combining hydrolysable carbon determinations with a variety of magnetic measurements sensitive to different droplet diameters. New measurements of ferromagnetic resonance response on density and magnetic separates from size fractions of soil 12023 are interpreted as evidence that hydrolysable carbon is preferentially associated with the larger, magnetically stable single-domain iron particles rather than with the smaller superparamagnetic droplets. For the former, there is a quite uniform ratio of iron to carbon both within a series of separates from a single soil, and among soils of widely varying FeO content.

  12. Percutaneous Fine Needle Biopsy in Pancreatic Tumors: A Study of 42 Cases

    Directory of Open Access Journals (Sweden)

    Piotr Lewitowicz

    2012-01-01

    Full Text Available The technological progress within the range of methods of pancreas imaging and their more common accessibility selects a group of patients requiring a microscopic diagnosis. Percutaneous fine needle aspiration biopsy under the control of ultrasonography (PCFNA/USG is the method commonly used in determining the character of a focal pancreatic lesion. Aim of the Work. An assessment of the accessibility of PCFNA biopsy in the assessment of solid and cystic changes in a pancreas and the correlation of the results of imaging examination, cytological smear and concentration of a serous marker CA19-9. Material and Methodology. In our material we analysed 43 cases of tumors of the pancreas among the patients who were at the average age of 59 ± 10.4 (14 women, 28 men diagnosed by PCFNA biopsy. Results. In a group we are 23 cases of cancer, 12 cases of inflammation and 7 cases of cellular atypia for which 2 cases of IPMN were included. The sensitivity of the method was 92.5% but specificity was 68%. In our opinion PCFNA/USG is a method of the comparable sensitivity and specificity with fine needle aspiration biopsy with EUS control and its efficiency depends to a considerable degree on experience and interdisciplinary collaboration.

  13. Geochemistry of Fine-grained Sediments and Sedimentary Rocks

    Science.gov (United States)

    Sageman, B. B.; Lyons, T. W.

    2003-12-01

    , 1981; Berner et al., 1983; Kump et al., 2000), with a shifting emphasis toward sophisticated characterization of the linkages among solid Earth, oceans, biosphere, cryosphere, atmosphere, and climate, mediated by short- and long-term biogeochemical cycles. As a result, one of the primary objectives of current geological inquiry is improved understanding of the interconnectedness and associated feedback among the cycles of carbon, nitrogen, phosphorous, oxygen, and sulfur, and their relationship to the history of Earth's climate. This "Earth System" approach involves uniformitarian extrapolations of knowledge gained from modern environments to proxy-based interpretations of environmental change recorded in ancient strata. The strength of modern data lies with direct observations of pathways and products of physical, chemical, and biological processes, but available time-series are short relative to the response times of many of the biogeochemical systems under study. By contrast, stratigraphically constrained geological data offer time-series that encompass a much fuller range of system response. But with the enhanced breadth of temporal resolution and signal amplitude provided by ancient sedimentary records comes a caveat - we must account for the blurring of primary paleo-environmental signals by preservational artifacts and understand that proxy calibrations are extended from the modern world into a nonsubstantively uniformitarian geological past.Fortunately, detrital sedimentary rocks preserve records of multiple proxies (dependent and independent) that illuminate the processes and conditions of sediment formation, transport, deposition, and burial. An integrated multiproxy approach offers an effective tool for deconvolving the history of biogeochemical cycling of, among other things, carbon and sulfur, and for understanding the range of associated paleo-environmental conditions (e.g., levels of atmospheric oxygen and carbon dioxide, oceanic paleoredox, and

  14. Studies on manufacturing technology of materials for fine chemical and electronic industry use

    Energy Technology Data Exchange (ETDEWEB)

    Choi, S.K.; Kim, B.G.; Chung, H.S.; Lee, J.C. [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Fine natural crystalline graphite which is used as a source material of a high electrically conductive film and an addition of advanced high functional solid lubricant. For use high electrically conductive film and advanced high functional solid lubricant, add new and advanced high functional properties to fine graphite powder through surface modification with gas and organic materials. Surface modification methods: 1) Searching for suitable surfactant to improve dispersing characteristics in aqueous system. 2) Adsorption with oxygen on graphite surface to improve dispersing characteristics in oil. 3) Mechanochemical process using hybridization system is to shape control and spontaneous re-arrangement of the surface layer and interaction between the particle surface and extraneous molecules. In aqueous system, the optimum conditions for graphite to disperse is with 0.3-0.5% concentrations of surfactant Lomar D PWA-40 at pH range 10-11. In order to improve dispersing characteristics in oil, the optimum conditions to adsorb over 3.5% with oxygen on graphite surface are as follows: - Tip speed {yields} 3.9 m/sec, - Reaction time {yields} at least 30 min. at 120 deg.C - inert gas and pressure {yields} dried air, 1 kgf/cm{sup 2}. The oxygen contents acts critical point for dispersing graphite in oil system so needs to control oxygen contents by use of air pressure in reacting mill. Chemical methods for coating with Stearic acid and Paraffin need above 15 weight % to graphite powders. Mechanochemical process using hybridization system is to shape control and spontaneous re-arrangement of the surface layer and interaction between the particle surface and extraneous molecules. (author). 45 refs., 9 tabs., 23 figs.

  15. Seismic characterization of hydrates in faulted, fine-grained sediments of Krishna-Godavari basin: Unified imaging

    Digital Repository Service at National Institute of Oceanography (India)

    Jaiswal, P.; Dewangan, P.; Ramprasad, T.; Zelt, C.A.

    ; in coarse-grain sediments, they can reside in pore-spaces, support the sediment framework as load-bearing grains, or bind the sediment grains as cement; in fine-grained sediments, they can create or occupy veins and fractures; on or near the seafloor... of interest to communities investigating climate change (Svensen et al., 2004), energy resources (Collett, 2002), and seafloor stability (Rothwell et al., 1998). When buried below the base of the GHSZ, hydrates become unstable and dissociate from a solid...

  16. Vilfredo Pareto e la fine del Sociale

    Directory of Open Access Journals (Sweden)

    Francesco Antonelli

    2017-08-01

    Full Text Available Il mondo contemporaneo è profondamente segnato dal declino delle pratiche e delle teorie sulla Società (Busino 1981: lì dove la modernità industriale è stata caratterizzata dal dominio “organicistico” dell’homo sociologicus, inteso come un attore definito dai suoi ruoli, integrato da strutture impersonali e parte di un sistema conflittuale prevalentemente economico (Dahrendorf 2010; Touraine 2008, la seconda modernità post-industriale e globale mette al centro il primato e l’autonomia dell’individuo. Questa fine della Società come fonte della moralità e dell’individuazione, al vertice della quale vi era lo Stato-nazione, ha dato vita a tre discorsi teorici, sospesi tra l’euristico e il normativo: il primo discorso promuove l’idea di una società degli individui che si autogoverna e si autoregola nel quadro del mercato globale, vista come la principale istituzione in grado di realizzare un equilibrio tra efficienza e soggettivazione; questo mercato non può comunque essere lasciato completamente a se stesso ma abbisogna di strumenti regolativi in grado di salvaguardare quel equilibrio: gli ordoliberalisti e, più in generale, i neoliberisti condividono questa posizione (Comisso 2017; Felice 2008; Foucault 2005; Röpke 2004. Il secondo discorso mette al centro l’idea di un soggetto personale, definito in maniera giusnaturalistica, che si oppone ai processi manipolativi e di dominio del sistema globale di potere. Questa idea di soggetto è anche la pietra angolare di ricostruzione possibile di un nuovo mondo caratterizzato dall’“universalismo delle differenze”: tra gli altri, Alain Touraine (2013; 1988, Martha Nussbaum (2013 e Nadia Urbinati (2011 condividono questo orientamento liberal. Il secondo discorso Infine, il terzo discorso ruota intorno ad un’idea di Sé desiderante e creativo che, attraverso idee come quelle di “moltitudine” (in luogo della categoria moderna di “popolo” e di “comune” (al

  17. SHAPE ANALYSIS OF FINE AGGREGATES USED FOR CONCRETE

    Directory of Open Access Journals (Sweden)

    Huan He

    2016-12-01

    Full Text Available Fine aggregate is one of the essential components in concrete and significantly influences the material properties. As parts of natures, physical characteristics of fine aggregate are highly relevant to its behaviors in concrete. The most of previous studies are mainly focused on the physical properties of coarse aggregate due to the equipment limitations. In this paper, two typical fine aggregates, i.e. river sand and crushed rock, are selected for shape characterization. The new developed digital image analysis systems are employed as the main approaches for the purpose. Some other technical methods, e.g. sieve test, laser diffraction method are also used for the comparable references. Shape characteristics of fine aggregates with different origins but in similar size ranges are revealed by this study. Compared with coarse aggregate, fine grains of different origins generally have similar shape differences. These differences are more significant in surface texture properties, which can be easily identified by an advanced shape parameter: bluntness. The new image analysis method is then approved to be efficient for the shape characterization of fine aggregate in concrete.

  18. VERTICAL FLOW OF GAS-LIQUID-SOLID PARTICLES SYSTEM

    OpenAIRE

    幡手, 泰雄; 野村, 博; 碇, 醇; ハタテ, ヤスオ; ノムラ, ヒロシ; イカリ, アツシ; HATATE, Yasuo; Nomura, Hiroshi; IKARI, Atsushi

    1983-01-01

    It is significant to know the hydrodynamic characteristics of the system in the design and scale-up of reactors containing gas-liquid-solid particles system. As a fundamental study of such a three-phase flow, the gas holdup and the pressure drop were measured in the vertical tubes, through which various mixtures of air, water, and fine glass-sphere, particles were passed. Three kinds of glass particles were used the average sizes of which were 30, 60 and 90 μm. Two kinds of tubes, 15 an...

  19. Solid Phase Characterization of Solids Recovered from Failed Sluicer Arm

    Energy Technology Data Exchange (ETDEWEB)

    Cooke, Gary A. [Hanford Site (HNF), Richland, WA (United States)

    2015-03-09

    The Enclosure to this memo discusses the solid phase characterization of a solid sample that was retrieved from the single-shell Tank 241-C-111 extended reach sluicer #2. This sluicer, removed from riser #3 on September 25, 2014, was found to have approximately 0.4 gallons of solid tank waste adhering to the nozzle area.

  20. The plasma-solid transition

    CERN Document Server

    Celebonovic, V

    2001-01-01

    Using a criterion proposed by Salpeter and standard solid-state physics,we have determined conditions for the occurence of the plasma-solid transition.Possible astrophysical applications are discussed.

  1. Solid residues; Os residuos solidos

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This chapter gives a general overview on the general effects of the solid waste pollution, the principal pollutants emitted by the oil refineries, control actions for the solid waste emissions, the minimization actions, and the effluent treatment.

  2. Atmospheric Light Detection and Ranging (LiDAR) Coupled With Point Measurement Air Quality Samplers to Measure Fine Particulate Matter (PM) Emissions From Agricultural Operations: The Los Banos CA Fall 2007 Tillage Campaign.

    Science.gov (United States)

    Airborne particles, especially fine particulate matter 2.5 micrometers (μm) or less in aerodynamic diameter (PM2.5), are microscopic solids or liquid droplets that can cause serious health problems, including increased respiratory symptoms such as coughing or difficulty breathing...

  3. Statistical thermodynamics of aerosols and the gas-solid Joule-Thomson effect

    Science.gov (United States)

    Pierotti, Robert A.; Rybolt, Thomas R.

    1984-04-01

    Due to the adsorption of a gas by a solid, it is expected that an aerosol created by dispersing a fine powder in a gas would have unique thermodynamic properties not found in pure or mixed gases. The virial equation of state associated with an aerosol dusty gas is obtained from statistical thermodynamic considerations. In the theoretical model presented here, the aerosol is considered to be a two component fluid made up of solid particles and gas molecules. The aerosol virial equation of state is used to derive an expression for the Joule-Thomson effect associated with a gas-solid dispersion. The magnitude of the gas-solid Joule-Thomson effect is expressed in terms of gas and gas-solid virial coefficients. Previous adsorption data for an argon-porous carbon system is used to obtain gas-solid virial coefficients and to predict the magnitude of the gas-solid Joule-Thomson effect. A significant enhancement of the Joule-Thomson effect is predicted for gas-solid systems which display a strong interaction. For example, at a temperature of 300 K an argon-Saran 746 porous carbon aerosol system at a concentration of (0.4 g of powder/l of gas) is predicted to have a gas-solid Joule-Thomson coefficient of 3.6 K/atm which is ten times greater than the effect for pure argon.

  4. Some features of raman scattering by molecules adsorbed on metal crystal faces and a fine light structure

    Science.gov (United States)

    Polubotko, A. M.

    2013-07-01

    The paper analyzes some experiments on Raman scattering by molecules adsorbed on the face (111) of silver monocrystals performed by A. Campion et al. From the existence of the forbidden line A 2 u of benzene, the conclusion about existence of the surface field, caused by atomic structure of the surface is made. The relatively large intensity of this line allows to make a conclusion about large influence of the electromagnetic field spatial inhomogeneity in crystals on their optical properties. The difference between this field and a regular plane wave, which usually describes propagation of electromagnetic field in solids is named as a fine light structure. The influence of this structure on optical properties of solids is pointed out.

  5. Some Features of Raman Scattering by Molecules Adsorbed on Metal Crystal Faces and a Fine Light Structure

    CERN Document Server

    Polubotko, A M

    2013-01-01

    The paper analyzes some experiments on Raman scattering by molecules adsorbed on the face (111) of silver monocrystals performed by A. Campion et al. From the existence of the forbidden line of benzene, the conclusion about existence of the surface field, caused by atomic structure of the surface is made. The relatively large intensity of this line allows to make a conclusion about large influence of the electromagnetic field spatial inhomogeneity in crystals on their optical properties. The difference between this field and a regular plane wave, which usually describes propagation of electromagnetic field in solids is named as a fine light structure. The influence of this structure on optical properties of solids is pointed out.

  6. Electro-Discharge Fine Truing of Metal-Bonded Fine-Grain Diamond Wheel Based on Real-Time Monitoring

    Institute of Scientific and Technical Information of China (English)

    JIN Weidong; REN Chengzu; HUA Jinhai; WANG Taiyong

    2005-01-01

    A data acquisition system based on LabVIEW is designed and implemented, and electro-discharge(ED) fine truing of metal-bonded fine-grain diamond wheel based on real-time monitoring is researched. Real-time monitoring not only makes efficient impulse specification of ED truing easily obtained, but also is good for timely identifying no-load, avoiding short circuit and arc discharge phenomena and then for obtaining normal machining state. ED fine truing of the fine-grain wheel includes two steps: rough truing for high efficiency and fine truing for high precision. Final ED truing precision and efficiency not only depend on electric process specification, but also is concerned with electrode shape, insulated performance of operating fluid and vertical feed quantity value and frequency. Experiments indicate that ED fine truing based on real-time monitoring can improve the truing precision and efficiency. Average machining efficiency of W10 wheel is about 0.95 μm/min; the final run-out by ED truing is less than 2 μm.

  7. Acoustics of solids

    CERN Document Server

    Beltzer, Abraham I

    1988-01-01

    Technological developments in composite materials, non-destructive testing, and signal processing as well as biomedical applications, have stimulated wide-ranging engineering investigations of heterogeneous, anisotropic media and surface waves of different types. Wave propagation in solids is now of considerable importance in a variety of applications. The book presents many of the key results in this field and interprets them from a unified engineering viewpoint. The conceptual importance and relevance for applications were the prevailing criteria in selecting the topics. Included are body and surface waves in elastic, viscoelastic, and piezoelectric media and waveguides, with emphasis on the effects of inhomogeneity and anisotropy. The book differs in many aspects from the other monographs dealing with wave propagation in solids. It focuses on physically meaningful theoretical models, a broad spectrum of which is covered, and not on mathematical techniques. Some of the results, particularly those dealing wi...

  8. Edge remap for solids

    Energy Technology Data Exchange (ETDEWEB)

    Kamm, James R.; Love, Edward; Robinson, Allen C; Young, Joseph G.; Ridzal, Denis

    2013-12-01

    We review the edge element formulation for describing the kinematics of hyperelastic solids. This approach is used to frame the problem of remapping the inverse deformation gradient for Arbitrary Lagrangian-Eulerian (ALE) simulations of solid dynamics. For hyperelastic materials, the stress state is completely determined by the deformation gradient, so remapping this quantity effectively updates the stress state of the material. A method, inspired by the constrained transport remap in electromagnetics, is reviewed, according to which the zero-curl constraint on the inverse deformation gradient is implicitly satisfied. Open issues related to the accuracy of this approach are identified. An optimization-based approach is implemented to enforce positivity of the determinant of the deformation gradient. The efficacy of this approach is illustrated with numerical examples.

  9. Thin Solid Oxide Cell

    DEFF Research Database (Denmark)

    2010-01-01

    The present invention relates to a thin and in principle unsupported solid oxide cell, comprising at least a porous anode layer, an electrolyte layer and a porous cathode layer, wherein the anode layer and the cathode layer comprise an electrolyte material, at least one metal and a catalyst...... material, and wherein the overall thickness of the thin reversible cell is about 150 [mu]m or less, and to a method for producing same. The present invention also relates to a thin and in principle unsupported solid oxide cell, comprising at least a porous anode layer, an electrolyte layer and a porous...... cathode layer, wherein the anode layer and the cathode layer comprise an electrolyte material and a catalyst material, wherein the electrolyte material is doper zirconia, and wherein the overall thickness of the thin reversible cell is about 150 [mu]m or less, and to a method for producing same...

  10. Amorphous pharmaceutical solids.

    Science.gov (United States)

    Vranić, Edina

    2004-07-01

    Amorphous forms are, by definition, non-crystalline materials which possess no long-range order. Their structure can be thought of as being similar to that of a frozen liquid with the thermal fluctuations present in a liquid frozen out, leaving only "static" structural disorder. The amorphous solids have always been an essential part of pharmaceutical research, but the current interest has been raised by two developments: a growing attention to pharmaceutical solids in general, especially polymorphs and solvates and a revived interest in the science of glasses and the glass transition. Amorphous substances may be formed both intentionally and unintentionally during normal pharmaceutical manufacturing operations. The properties of amorphous materials can be exploited to improve the performance of pharmaceutical dosage forms, but these properties can also give rise to unwanted effects that need to be understood and managed in order for the systems to perform as required.

  11. Solid State Laser

    Science.gov (United States)

    1990-01-01

    The Titan-CW Ti:sapphire (titanium-doped sapphire) tunable laser is an innovation in solid-state laser technology jointly developed by the Research and Solid State Laser Divisions of Schwartz Electro-optics, Inc. (SEO). SEO is producing the laser for the commercial market, an outgrowth of a program sponsored by Langley Research Center to develop Ti:sapphire technology for space use. SEO's Titan-CW series of Ti:sapphire tunable lasers have applicability in analytical equipment designed for qualitative analysis of carbohydrates and proteins, structural analysis of water, starch/sugar analyses, and measurements of salt in meat. Further applications are expected in semiconductor manufacture, in medicine for diagnosis and therapy, and in biochemistry.

  12. Fracture of brittle solids

    CERN Document Server

    Lawn, Brian

    1993-01-01

    This is an advanced text for higher degree materials science students and researchers concerned with the strength of highly brittle covalent-ionic solids, principally ceramics. It is a reconstructed and greatly expanded edition of a book first published in 1975. The book presents a unified continuum, microstructural and atomistic treatment of modern day fracture mechanics from a materials perspective. Particular attention is directed to the basic elements of bonding and microstructure that govern the intrinsic toughness of ceramics. These elements hold the key to the future of ceramics as high-technology materials--to make brittle solids strong, we must first understand what makes them weak. The underlying theme of the book is the fundamental Griffith energy-balance concept of crack propagation. The early chapters develop fracture mechanics from the traditional continuum perspective, with attention to linear and nonlinear crack-tip fields, equilibrium and non-equilibrium crack states. It then describes the at...

  13. Thin Solid Oxide Cell

    DEFF Research Database (Denmark)

    2010-01-01

    The present invention relates to a thin and in principle unsupported solid oxide cell, comprising at least a porous anode layer, an electrolyte layer and a porous cathode layer, wherein the anode layer and the cathode layer comprise an electrolyte material, at least one metal and a catalyst...... material, and wherein the overall thickness of the thin reversible cell is about 150 [mu]m or less, and to a method for producing same. The present invention also relates to a thin and in principle unsupported solid oxide cell, comprising at least a porous anode layer, an electrolyte layer and a porous...... cathode layer, wherein the anode layer and the cathode layer comprise an electrolyte material and a catalyst material, wherein the electrolyte material is doper zirconia, and wherein the overall thickness of the thin reversible cell is about 150 [mu]m or less, and to a method for producing same...

  14. Amorphous Solid Water:

    DEFF Research Database (Denmark)

    Wenzel, Jack; Linderstrøm-Lang, C. U.; Rice, Stuart A.

    1975-01-01

    The structure factor of amorphous solid D2O deposited from the vapor at 10°K has been obtained by measuring the neutron diffraction spectrum in the wave vector transfer from 0.8 to 12.3 reciprocal angstroms. The results indicate that the phase investigated is amorphous and has a liquiid-like stru......The structure factor of amorphous solid D2O deposited from the vapor at 10°K has been obtained by measuring the neutron diffraction spectrum in the wave vector transfer from 0.8 to 12.3 reciprocal angstroms. The results indicate that the phase investigated is amorphous and has a liquiid...

  15. Municipal Solid Waste Resources

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-01

    Municipal solid waste (MSW) is a source of biomass material that can be utilized for bioenergy production with minimal additional inputs. MSW resources include mixed commercial and residential garbage such as yard trimmings, paper and paperboard, plastics, rubber, leather, textiles, and food wastes. Waste resources such as landfill gas, mill residues, and waste grease are already being utilized for cost-effective renewable energy generation. MSW for bioenergy also represents an opportunity to divert greater volumes of residential and commercial waste from landfills.

  16. Solid waste handling

    Energy Technology Data Exchange (ETDEWEB)

    Parazin, R.J.

    1995-05-31

    This study presents estimates of the solid radioactive waste quantities that will be generated in the Separations, Low-Level Waste Vitrification and High-Level Waste Vitrification facilities, collectively called the Tank Waste Remediation System Treatment Complex, over the life of these facilities. This study then considers previous estimates from other 200 Area generators and compares alternative methods of handling (segregation, packaging, assaying, shipping, etc.).

  17. Solid-state memcapacitor

    OpenAIRE

    Martinez, J; Di Ventra, M.; Pershin, Yu. V.

    2009-01-01

    We suggest a possible realization of a solid-state memory capacitive (memcapacitive) system. Our approach relies on the slow polarization rate of a medium between plates of a regular capacitor. To achieve this goal, we consider a multi-layer structure embedded in a capacitor. The multi-layer structure is formed by metallic layers separated by an insulator so that non-linear electronic transport (tunneling) between the layers can occur. The suggested memcapacitor shows hysteretic charge-voltag...

  18. Diffusion in nanocrystalline solids

    OpenAIRE

    Chadwick, Alan V.

    2016-01-01

    Enhanced atomic migration was an early observation from experimental studies into nanocrystalline solids. This contribution presents an overview of the available diffusion data for simple metals and ionic materials in nanocrystalline form. It will be shown that enhanced diffusion can be interpreted in terms of atomic transport along the interfaces, which are comparable to grain boundaries in coarse-grained analogues. However, the method of sample preparation is seen to play a major role in...

  19. Solid state magnetism

    CERN Document Server

    Crangle, John

    1991-01-01

    Solid state magnetism is important and attempts to understand magnetic properties have led to an increasingly deep insight into the fundamental make up of solids. Both experimental and theoretical research into magnetism continue to be very active, yet there is still much ground to cover before there can be a full understanding. There is a strong interplay between the developments of materials science and of magnetism. Hundreds of new materials have been dis­ covered, often with previously unobserved and puzzling magnetic prop­ erties. A large and growing technology exists that is based on the magnetic properties of materials. Very many devices used in everyday life involve magnetism and new applications are being invented all the time. Under­ standing the fundamental background to the applications is vital to using and developing them. The aim of this book is to provide a simple, up-to-date introduction to the study of solid state magnetism, both intrinsic and technical. It is designed to meet the needs a...

  20. Interstellar Solid Hydrogen

    CERN Document Server

    Lin, Ching Yeh; Walker, Mark A

    2011-01-01

    We consider the possibility that solid molecular hydrogen is present in interstellar space. If so cosmic-rays and energetic photons cause ionisation in the solid leading to the formation of H6+. This ion is not produced by gas-phase reactions and its radiative transitions therefore provide a signature of solid H2 in the astrophysical context. The vibrational transitions of H6+ are yet to be observed in the laboratory, but we have characterised them in a quantum-theoretical treatment of the molecule; our calculations include anharmonic corrections, which are large. Here we report on those calculations and compare our results with astronomical data. In addition to the H6+ isotopomer, we focus on the deuterated species (HD)3+ which is expected to dominate at low ionisation rates as a result of isotopic condensation reactions. We can reliably predict the frequencies of the fundamental bands for five modes of vibration. For (HD)3+ all of these are found to lie close to some of the strongest of the pervasive mid-in...

  1. Haggling over the fine-tuning price of LEP

    Science.gov (United States)

    Chankowski, Piotr H.; Ellis, John; Olechowski, Marek; Pokorski, Stefan

    1999-04-01

    We amplify previous discussions of the fine-tuning price to be paid by supersymmetric models in the light of LEP data. The whole range of tan β is discussed, including large values. In the minimal supergravity model with universal gaugino and scalar masses, a small fine-tuning price is possible only for intermediate values of tan β and for a small range of superpartner masses. Moreover, the fine-tuning price in this region is significantly higher if we require β-τ Yukawacoupling unification. We interpret the significant increase after LEP of the fine-tuning price in the minimal supergravity model as a message for theory and not for the experiment. For possible choices of low-energy parameters in the MSSM consistent with present experimental constraints and, optionally, with some other theoretical assumptions such as ifb-τ Yukawa-coupling unification, a measure of the amount of fine tuning becomes an interesting criterion for the naturalness of various theoretical models for mass terms in the MSSM Lagrangian. In particular, we emphasize that the fine-tuning price will depend on the actual solution to the μ problem. We illustrate the relevance of this fact by considering a simple ansatz of linear dependence of μ on M {1}/{2} or A0, showing that big price reductions are obtained in such cases. Significant price reductions are also obtained for large tan β if non-universal soft Higgs mass parameters are allowed. We also study input relations between MSSM parameters suggested in some interpretations of string theory: the price may depend significantly on these inputs, potentially providing guidance for building string models. However, in the available models the fine-tuning price may not be reduced significantly.

  2. Computer prediction system on solid/solid reaction kinetics

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A computer software system of kinetic predication of solid/solid reaction, KinPreSSR, was developed using Visual C++ and FoxPro. It includes two main modules, REACTION and DIFFUSION. KinPreSSR deals with the kinetics on the diffusion in solids as well as solid/solid reactions. The REACTION module in KinPreSSR was mainly described, which has organized the commonly recognized kinetic models, parameters, and employed both numerical and graphical methods for data analyses. The proper combination between the kinetic contents and the analytical methods enables users to use KinPreSSR for the evaluation and prediction of solid/solid reactions interested. As an example to show some of functions of KinPreSSR, the kinetics analysis for the reaction between SrCO3 and TiO2 powders to form SrTiO3 with a series of kinetic data from isothermal measurements was demonstrated.

  3. Studies on composite solid propellant with tri-modal ammonium perchlorate containing an ultrafine fraction

    Directory of Open Access Journals (Sweden)

    K.V. Suresh Babu

    2017-08-01

    Full Text Available Composite solid propellant is prepared using tri-modal Ammonium perchlorate (AP containing coarse, fine and ultrafine fractions of AP with average particle size (APS 340, 40 and 5 μm respectively, in various compositions and their rheological, mechanical and burn rate characteristics are evaluated. The optimum combination of AP coarse to fine to ultrafine weight fraction was obtained by testing of series of propellant samples by varying the AP fractions at fixed solid loading. The concentration of aluminium was maintained constant throughout the experiments for ballistics requirement. The propellant formulation prepared using AP with coarse to fine to ultrafine ratio of 67:24:9 has lowest viscosity for the propellant paste and highest tensile strength due to dense packing as supported by the literature. A minimum modulus value was also observed at 9 wt. % of ultrafine AP concentration indicates the maximum solids packing density at this ratio of AP fractions. The burn rate is evaluated at different pressures to obtain pressure exponent. Incorporation of ultrafine fraction of AP in propellant increased burn rate without adversely affecting the pressure exponent. Higher solid loading propellants are prepared by increased AP concentration from 67 to 71 wt. % using AP with coarse to fine to ultrafine ratio of 67:24:9. Higher solid content up to 89 wt. % was achieved and hence increased solid motor performance. The unloading viscosity showed a trend with increased AP content and the propellant couldn't able to cast beyond 71 wt. % of AP. Mechanical properties were also studied and from the experiments noticed that % elongation decreased with increased AP content from 67 to 71 wt.%, whereas tensile strength and modulus increased. Burn rate increased with increased AP content and observed that pressure exponent also increased and it is high for the propellant containing with 71 wt.% of AP due to increased oxidiser to fuel ratio. Catalysed

  4. Influence of fine threads and platform-switching on crestal bone stress around implant-a three-dimensional finite element analysis.

    Science.gov (United States)

    Khurana, Pardeep; Sharma, Arun; Sodhi, Kiranmeet Kaur

    2013-12-01

    The aims of this study were to investigate the effect of implant fine threads on crestal bone stress compared to a standard smooth implant collar and to analyze how different abutment diameters influenced the crestal bone stress level. Three-dimensional finite element imaging was used to create a cross-sectional model in SolidWorks 2007 software of an implant (5-mm platform and 10 mm in length) placed in the premolar region of the mandible. The implant model was created to resemble a commercially available fine thread implant. Abutments of different diameters (5.0 mm: standard, 4.5 mm, 4.0 mm, and 3.5 mm) were loaded with a force of 100 N at 90° vertical and 40° oblique angles. Finite element analysis was done in COSMOSWorks software, which was used to analyze the stress patterns in bone, especially in the crestal region. Upon loading, the fine thread implant model had greater stress at the crestal bone adjacent to the implant than the smooth neck implant in both vertical and oblique loading. When the abutment diameter decreased progressively from 5.0 mm to 4.5 mm to 4 mm and to 3.5 mm the thread model showed a reduction of stress at the crestal bone level from 23.2 MPa to 15.02 MPa for fine thread and from 22.7 to 13.5 MPa for smooth collar implant group after vertical loading and from 43.7 MPa to 33.1 MPa in fine thread model and from 36.9 to 20.5 MPa in smooth collar implant model after oblique loading. Fine threads increase crestal stress upon loading. Reduced abutment diameter that is platform switching resulted in less stress translated to the crestal bone in the fine thread and smooth neck.

  5. Strain effects in Nb3Al multifilamentary conductors prepared by phase transformation from bcc supersaturated-solid solution

    NARCIS (Netherlands)

    Takeuchi, T.; Iijima, Y.; Inoue, K.; Wada, H.; Haken, ten B.; Kate, ten H.H.J.; Fukuda, K.; Iwaki, G.; Sakai, S.; Moriai, H.

    1997-01-01

    Strain effects on critical current densities have been examined for conductors containing nearly stoichiometric Nb3Al filaments with fine grains. The Nb3Al phase in these multifilamentary conductors are prepared by phase transformation from supersaturated Nb(Al) bcc solid solution and show high-fiel

  6. Permeability of wood pellets in the presence of fines.

    Science.gov (United States)

    Yazdanpanah, F; Sokhansanj, S; Lau, A K; Lim, C J; Bi, X; Melin, S; Afzal, M

    2010-07-01

    Broken pellets and fines are produced when pellets are handled. The resistance to air flow was measured for clean pellets and for pellets mixed with 1-20% broken pellets (fines). A pellet diameter was 6mm. The lengths ranged from 6 to 12 mm. Clean pellets were defined as particles that remained on a 4mm screen. A typical sieve analysis showed 30% of the mass of particles that passed through the 4mm screen was smaller than 1mm. The airflow rates used in the experiment ranged from 0.004 to 0.357 ms(-1). The corresponding pressure drop ranged from 1.9 to 271 Pam(-1) for clean pellets, from 4.8 to 1100 Pam(-1) for 10% fines content, and from 7.9 to 1800 Pam(-1) for 20% fines content. Coefficients of Hukill and Ives' equation were estimated for clean pellets and a multiplier was defined to calculate pressure drop for pellets mixed with fines.

  7. Permeability of wood pellets in the presence of fines

    Energy Technology Data Exchange (ETDEWEB)

    Yazdanpanah, F. [University of British Columbia, Vancouver; Lau, A.K. [University of British Columbia, Vancouver; Sokhansanj, Shahabaddine [ORNL; Lim, C. Jim [University of British Columbia, Vancouver; Melin, Staffan [University of British Columbia, Vancouver; Bi, X.T. [University of British Columbia, Vancouver; Afzal, M [University of New Brunswick

    2010-03-01

    Broken pellets and fines are produced during mechanical handlings of wood pellets. The resistance to air flow was measured for clean pellets and for pellets mixed with 1 to 20% broken pellets (fines). A pellet diameter was 6 mm. The lengths ranged from from 6 to 12 mm. Clean pellets were defined as particles that remained on a 4 mm screen. A typical sieve analysis showed 30% of the mass of particles passed through the 4 mm screen were smaller than 1 mm. The airflow rates used in the experiment ranged from 0.004 to 0.357 ms-1. The corresponding pressure drop ranged from 1.9 Pa m-1 to 271 Pa m-1 for clean pellets and from 4.8 to 1100 Pa m 1 for pellets mixed with 10% fines. The pressure drop increased for pellets mixed with increasing fines content. Coefficients of Hukill and Ives equation were estimated for clean pellets and a multiplier was defined to calculate pressure drop for pellets mixed with fines.

  8. Stabilization of Black Cotton Soil Using Micro-fine Slag

    Science.gov (United States)

    Shukla, Rajesh Prasad; Parihar, Niraj Singh

    2016-09-01

    This work presents the results of laboratory tests conducted on black cotton soil mixed with micro-fine slag. Different proportions of micro-fine slag, i.e., 3, 6, 9, 12 and 15 % were mixed with the black cotton soil to improve soil characteristics. The improvement in the characteristics of stabilized soil was assessed by evaluating the changes in the physical and strength parameters of the soil, namely, the Atterberg limits, free swell, the California Bearing Ratio (CBR), compaction parameters and Unconfined Compressive Strength (UCS). The mixing of micro-fine slag decreases the liquid limit, plasticity index and Optimum Moisture Contents (OMC) of the soil. Micro-fine slag significantly increases the plastic limit, UCS and CBR of the soil up to 6-7 % mixing, but mixing of more slag led to decrease in the UCS and CBR of the soil. The unsoaked CBR increased by a substantial amount unlike soaked CBR value. The swell potential of the soil is reduced from medium to very low. The optimum amount of micro-fine slag is found to be approximately 6-7 % by the weight of the soil.

  9. Fine-grained sediment dispersal along the California coast

    Science.gov (United States)

    Warrick, Jonathan A.; Storlazzi, Curt D.

    2013-01-01

    Fine-grained sediment (silt and clay) enters coastal waters from rivers, eroding coastal bluffs, resuspension of seabed sediment, and human activities such as dredging and beach nourishment. The amount of sediment in coastal waters is an important factor in ocean ecosystem health, but little information exists on both the natural and human-driven magnitudes of fine-grained sediment delivery to the coastal zone, its residence time there, and its transport out of the system—information upon which to base environmental assessments. To help fill these information gaps, the U.S. Geological Survey has partnered with Federal, State, and local agencies to monitor fine-grained sediment dispersal patterns and fate in the coastal regions of California. Results of these studies suggest that the waves and currents of many of the nearshore coastal settings of California are adequately energetic to transport fine-grained sediment quickly through coastal systems. These findings will help with the management and regulation of fine-grained sediment along the U.S. west coast.

  10. Landscape and fine scale habitat associations of the Loggerhead Shrike

    Science.gov (United States)

    Michaels, H.L.; Cully, J.E.

    1998-01-01

    This study was conducted to determine landscape and fine-scale vegetative variables associated with breeding Loggerhead Shrikes (Lanius ludovicianus) on Fort Riley Military Reservation, Kansas. Because Fort Riley is an Army training site, the influences of training disturbance to the vegetation, and range management practices on bird habitat patterns were also investigated. Breeding birds were surveyed in 1995 and 1996 using point counts. Survey plots were identified, a priori, at the landscape scale as either grassland, savannah, or woodland edge according to cover by woody vegetation. In 1996, fine-scale habitat at survey points and at bird use sites was measured and a principal components analysis used to characterize the fine-scale herbaceous vegetation structure. A military disturbance index was developed to quantify the severity of vehicle disturbance to the vegetation at survey and bird use sites. Shrikes were associated with savannah habitat at the landscape scale. Sites used by Loggerhead Shrikes were characterized at the fine-scale by tall, sparse, structurally heterogeneous herbaceous vegetation with high standing dead plant cover and low litter cover. At the fine-scale, tree and shrub density did not differ between sites used and not used by shrikes. Used sites did not differ from survey sites with respect to military training disturbance, hay harvest, or the number of years since a site was last burned. Our results in this study suggest that the shifting mosaic of vegetation on Fort Riley resulting from training and range management practices maintains adequate habitat for breeding shrikes.

  11. Modeling downstream fining in sand-bed rivers. II: Application

    Science.gov (United States)

    Wright, S.; Parker, G.

    2005-01-01

    In this paper the model presented in the companion paper, Wright and Parker (2005) is applied to a generic river reach typical of a large, sand-bed river flowing into the ocean in order to investigate the mechanisms controlling longitudinal profile development and downstream fining. Three mechanisms which drive downstream fining are studied: a delta prograding into standing water, sea-level rise, and tectonic subsidence. Various rates of sea-level rise (typical of the late Holocene) and tectonic subsidence are modeled in order to quantify their effects on the degree of profile concavity and downstream fining. Also, several other physical mechanisms which may affect fining are studied, including the relative importance of the suspended versus bed load, the effect of the loss of sediment overbank, and the influence of the delta bottom slope. Finally, sensitivity analysis is used to show that the grain-size distribution at the interface between the active layer and substrate has a significant effect on downstream fining. ?? 2005 International Association of Hydraulic Engineering and Research.

  12. Transport of fine sediment over a coarse, immobile riverbed

    Science.gov (United States)

    Grams, Paul E.; Wilcock, Peter R.

    2014-01-01

    Sediment transport in cobble-boulder rivers consists mostly of fine sediment moving over a coarse, immobile bed. Transport rate depends on several interrelated factors: boundary shear stress, the grain size and volume of fine sediment, and the configuration of fine sediment into interstitial deposits and bed forms. Existing models do not incorporate all of these factors. Approaches that partition stress face a daunting challenge because most of the boundary shear is exerted on immobile grains. We present an alternative approach that divides the bed into sand patches and interstitial deposits and is well constrained by two clear end-member cases: full sand cover and absence of sand. Entrainment from sand patches is a function of their aerial coverage. Entrainment from interstices among immobile grains is a function of sand elevation relative to the size of the immobile grains. The bed-sand coverage function is used to predict the ratio of the rate of entrainment from a partially covered bed to the rate of entrainment from a completely sand-covered bed, which is determined using a standard sand transport model. We implement the bed-sand coverage function in a morphodynamic routing model and test it against observations of sand bed elevation and suspended sand concentration for conditions of nonuniform fine sediment transport in a large flume with steady uniform flow over immobile hemispheres. The results suggest that this approach may provide a simple and robust method for predicting the transport and migration of fine sediment through rivers with coarse, immobile beds.

  13. Measurements of solids concentration and axial solids velocity in gas-solid two-phase flows.

    NARCIS (Netherlands)

    Nieuwland, J.J.; Meijer, R.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    1996-01-01

    Several techniques reported in the literature for measuring solids concentration and solids velocity in (dense) gas-solid two-phase flow have been briefly reviewed. An optical measuring system, based on detection of light reflected by the suspended particles, has been developed to measure local soli

  14. Pulsed Power for Solid-State Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Gagnon, W; Albrecht, G; Trenholme, J; Newton, M

    2007-04-19

    Beginning in the early 1970s, a number of research and development efforts were undertaken at U.S. National Laboratories with a goal of developing high power lasers whose characteristics were suitable for investigating the feasibility of laser-driven fusion. A number of different laser systems were developed and tested at ever larger scale in pursuit of the optimum driver for laser fusion experiments. Each of these systems had associated with it a unique pulsed power option. A considerable amount of original and innovative engineering was carried out in support of these options. Ultimately, the Solid-state Laser approach was selected as the optimum driver for the application. Following this, the Laser Program at the Lawrence Livermore National Laboratory and the University of Rochester undertook aggressive efforts directed at developing the technology. In particular, at Lawrence Livermore National Laboratory, a series of laser systems beginning with the Cyclops laser and culminating in the present with the National Ignition Facility were developed and tested. As a result, a large amount of design information for solid-state laser pulsed power systems has been documented. Some of it is in the form of published papers, but most of it is buried in internal memoranda, engineering reports and LLNL annual reports. One of the goals of this book is to gather this information into a single useable format, such that it is easily accessed and understood by other engineers and physicists for use with future designs. It can also serve as a primer, which when seriously studied, makes the subsequent reading of original work and follow-up references considerably easier. While this book deals only with the solid-state laser pulsed power systems, in the bibliography we have included a representative cross section of papers and references from much of the very fine work carried out at other institutions in support of different laser approaches. Finally, in recent years, there has

  15. A 5-year-old girl with a congenital ganglioneuroma diagnosed by fine needle aspiration biopsy: a case report

    Directory of Open Access Journals (Sweden)

    Ponce-Camacho Marco

    2008-01-01

    Full Text Available Abstract Introduction Ganglioneuroma is a rare, benign, neuroblastic tumor arising mainly from the central or peripheral autonomic nervous system, especially the sympathetic system. The most affected anatomical sites are the posterior mediastinum, retroperitoneum, adrenal gland and head and neck soft tissue. In the current literature, reports of ganglioneuroma diagnosed by fine-needle aspiration and its cytological appearance are scarce. Case Presentation A 5-year-old girl presented with a mass in the cervical region since birth. Laboratory routine tests were within normal limits, ultrasonography demonstrated a solid and well-circumscribed lesion in the soft tissues of the cervical region. Fine needle aspiration biopsy was carried out, and the obtained smears showed a mixture of mature ganglion cells and groups of spindle cells suggestive of schwann cell origin. A diagnosis of ganglioneuroma was suggested. Core biopsy and surgical resection confirmed this diagnosis. Conclusion Congenital ganglioneuroma of the cervical region is an uncommon soft tissue benign neoplasm of neuroblastic origin, and it should be considered in the differential diagnosis of head and neck pediatric soft tissue tumors. Fine needle aspiration biopsy technique is a reliable method that can be used with confidence when dealing with pediatric soft tissue tumors.

  16. Fine Root Productivity and Dynamics on a Forested Floodplain in South Carolina

    Science.gov (United States)

    Terrell T. Baker; William Conner; H. B. Graeme Lockaby; John A. Stanturf; Marianne K. Burke

    2001-01-01

    The highly dynamic, fine root component of forested wetland ecosystems fine root dynamics is a challenging endeavor in any system, but the difficulties are particularly evident in forested floodplains where frequent hydrologic fluctuations directly influence fine root dynamics. Fine root (53 mm) biomass, production, and turnover were estimated for three soils...

  17. Establishing a molecular relationship between chondritic and cometary organic solids.

    Science.gov (United States)

    Cody, George D; Heying, Emily; Alexander, Conel M O; Nittler, Larry R; Kilcoyne, A L David; Sandford, Scott A; Stroud, Rhonda M

    2011-11-29

    Multidimensional solid-state NMR spectroscopy is used to refine the identification and abundance determination of functional groups in insoluble organic matter (IOM) isolated from a carbonaceous chondrite (Murchison, CM2). It is shown that IOM is composed primarily of highly substituted single ring aromatics, substituted furan/pyran moieties, highly branched oxygenated aliphatics, and carbonyl groups. A pathway for producing an IOM-like molecular structure through formaldehyde polymerization is proposed and tested experimentally. Solid-state (13)C NMR analysis of aqueously altered formaldehyde polymer reveals considerable similarity with chondritic IOM. Carbon X-ray absorption near edge structure spectroscopy of formaldehyde polymer reveals the presence of similar functional groups across certain Comet 81P/Wild 2 organic solids, interplanetary dust particles, and primitive IOM. Variation in functional group concentration amongst these extraterrestrial materials is understood to be a result of various degrees of processing in the parent bodies, in space, during atmospheric entry, etc. These results support the hypothesis that chondritic IOM and cometary refractory organic solids are related chemically and likely were derived from formaldehyde polymer. The fine-scale morphology of formaldehyde polymer produced in the experiment reveals abundant nanospherules that are similar in size and shape to organic nanoglobules that are ubiquitous in primitive chondrites.

  18. Recycling of PET bottles as fine aggregate in concrete.

    Science.gov (United States)

    Frigione, Mariaenrica

    2010-06-01

    An attempt to substitute in concrete the 5% by weight of fine aggregate (natural sand) with an equal weight of PET aggregates manufactured from the waste un-washed PET bottles (WPET), is presented. The WPET particles possessed a granulometry similar to that of the substituted sand. Specimens with different cement content and water/cement ratio were manufactured. Rheological characterization on fresh concrete and mechanical tests at the ages of 28 and 365days were performed on the WPET/concretes as well as on reference concretes containing only natural fine aggregate in order to investigate the influence of the substitution of WPET to the fine aggregate in concrete. It was found that the WPET concretes display similar workability characteristics, compressive strength and splitting tensile strength slightly lower that the reference concrete and a moderately higher ductility.

  19. Photoelectric Measurement of the Fineness of Raw Silk

    Institute of Scientific and Technical Information of China (English)

    Wan-chun FEI

    2010-01-01

    In order to precisely measure the diameters for obtaining the fineness of rolling raw silk, the physical features of raw silk are analyzed. By means of Fresnel principle, diffractions caused by different transparent raw silk filaments are analyzed and simulated. Image data of raw silk filament measured by digital CMOS camera are analyzed and processed for obtaining the precise diameters of the filament with the relative error of less than 1%. On the assumption of appropriate elliptic cross-section of the filament, the cross-section area is calculated as the fineness of the filament. Measurement experiments are carried out. Finally, some suggestions are proposed for photoelectric measuring the fineness of raw silk.

  20. Development of High Sensitivity Nuclear Emulsion and Fine Grained Emulsion

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, H.; Asada, T. [Department of Physics, Nagoya University, Nagoya 464-8602 (Japan); Naka, T. [Institute of Advanced Research, Nagoya University (Japan); Naganawa, N.; Kuwabara, K.; Nakamura, M. [Department of Physics, Nagoya University, Nagoya 464-8602 (Japan)

    2014-08-15

    Nuclear emulsion is a particle detector having high spacial resolution and angular resolution. It became useful for large statistics experiment thanks to the development of automatic scanning system. In 2010, a facility for emulsion production was introduced and R and D of nuclear emulsion began at Nagoya university. In this paper, we present results of development of the high sensitivity emulsion and fine grained emulsion for dark matter search experiment. Improvement of sensitivity is achieved by raising density of silver halide crystals and doping well-adjusted amount of chemicals. Production of fine grained emulsion was difficult because of unexpected crystal condensation. By mixing polyvinyl alcohol (PVA) to gelatin as a binder, we succeeded in making a stable fine grained emulsion.

  1. Magnetic phases in lunar fines - Metallic Fe or ferric oxides.

    Science.gov (United States)

    Tsay, F.-D.; Manatt, S. L.; Chan, S. I.

    1973-01-01

    The ferromagnetic resonance observed for the Apollo 11 and 12 lunar fines is characterized by an asymmetric lineshape with a narrower appearance on the high field side. This asymmetry together with an anisotropy energy which varies from +640 to +500 G over the temperature range of 80 to 298 K indicate that the ferromagnetic resonance arises from metallic Fe having the body-centered cubic structure and not from hematite, magnetite or other Fe(3+) ions in magnetite-like phases. The g-value, the lineshape asymmetry, and the temperature dependence of the linewidth for the Apollo 14 and 15 fines as reported by other workers are found to be essentially similar to those observed for the Apollo 11 and 12 fines.

  2. Manufacture of Fine-Pored Ceramics by the Gelcasting Method

    Directory of Open Access Journals (Sweden)

    Bronisław Psiuk

    2017-01-01

    Full Text Available The fine-pored materials represent a wide range of applications and searches are being continued to develop methods of their manufacturing. In the article, based on measurements on fine-grained powders of Al2O3, TiO2, and SiO2, it has been demonstrated that gelcasting can be relatively simple method of obtaining of nanoporous materials with high values of both specific surface area and open porosity. The powders were dispersed in silica sol, and the gelling initiator was NH4Cl. The usefulness of experiment design theory for developing of fine-pored materials with high porosity and specific surface area was also shown.

  3. Fine Tuning Mission to reach those influenced by Darwinism

    Directory of Open Access Journals (Sweden)

    Roger Tucker

    2014-01-01

    Full Text Available The scientifically aware section of the South African population is increasing. Many are being exposed to the concept of Darwinian evolution. Exposure has generated a religious sub �people group� who have problems with Christianity because they have been influenced by the naturalistic element in Darwinian philosophy. Christian antagonism towards evolution has often prejudiced them unfavourably towards the gospel. Recent discoveries concerning the fine-tuning of the universe have now presented a window of opportunity for overcoming this. It may enable the church to �fine-tune� its missionary approach to present them with the gospel in a more acceptable manner. It is suggested that Paul�s Areopagus speech provides a model for such cross-cultural evangelism. A section is included at the end, describing some objections that have been raised against the cosmological fine-tuning apologetic.

  4. Effects of cellular fine structure on scattered light pattern.

    Science.gov (United States)

    Liu, Caigen; Capjack, Clarence E

    2006-06-01

    Biological cells are complex in both morphological and biochemical structure. The effects of cellular fine structure on light scattered from cells are studied by employing a three-dimensional code named AETHER which solves the full set of Maxwell equations by using the finite-difference time-domain method. It is shown that changes in cellular fine structure can cause significant changes in the scattered light pattern over particular scattering angles. These changes potentially provide the possibility for distinguishability of cellular intrastructures. The effects that features of different intrastructure have on scattered light are discussed from the viewpoint of diagnosing cellular fine structure. Finally, we discuss scattered light patterns for lymphocyte-like cells and basophil-like cells.

  5. 3D WHOLE-PROMINENCE FINE STRUCTURE MODELING

    Energy Technology Data Exchange (ETDEWEB)

    Gunár, Stanislav; Mackay, Duncan H. [School of Mathematics and Statistics, University of St Andrews, North Haugh, St Andrews, KY16 9SS (United Kingdom)

    2015-04-20

    We present the first 3D whole-prominence fine structure model. The model combines a 3D magnetic field configuration of an entire prominence obtained from nonlinear force-free field simulations, with a detailed description of the prominence plasma. The plasma is located in magnetic dips in hydrostatic equilibrium and is distributed along multiple fine structures within the 3D magnetic model. Through the use of a novel radiative transfer visualization technique for the Hα line such plasma-loaded magnetic field model produces synthetic images of the modeled prominence comparable with high-resolution observations. This allows us for the first time to use a single technique to consistently study, in both emission on the limb and absorption against the solar disk, the fine structures of prominences/filaments produced by a magnetic field model.

  6. Helium 23P Fine Structure Measurement in a Discharge Cell

    Science.gov (United States)

    Zelevinsky, T.; Farkas, D.; Gabrielse, G.

    2005-12-01

    A precise measurement of helium 23P fine structure was carried out in a discharge cell using Doppler-free laser spectroscopy. It is the only known experiment to directly measure all three fine structure intervals at a 1 kHz level of accuracy. The 23P1 - 23P2 interval value agrees with other experiments but disagrees with theoretical predictions of two-electron QED. When this disagreement is resolved, the 23P0 - 23P1 interval measurement reported here will allow a determination of the fine structure constant to 14 parts in 109, surpassing the precision of the well known QED-independent quantum Hall effect and Josephson effect determinations. The discharge cell is shown to be advantageous in the study and correction of systematic frequency shifts related to light pressure, and the use of the cell ensures that the possible systematic errors are substantially different from those reported in other experiments.

  7. Theory of the fine structure of auroral kilometric radiation

    Science.gov (United States)

    Grabbe, C. L.

    1982-01-01

    Recent data from ISEE 1 show auroral kilometric radiation (AKR) with finely separated bands in frequency. The observation that the AKR fine structure frequency separation is about equal to the ion cyclotron frequency at the AKR source is strong evidence for the interaction of AKR and electrostatic ion cyclotron (EIC) waves in the source, as proposed by Grabbe et al. (1980) to explain the origin of AKR. It is pointed out that no other wave of frequency close to the band separation is known to exist in the auroral source region. The fine structure observed in the source region AKR is the first evidence for EIC waves in the lower source region (3000 - 5000 km attitude), as required in the theory of Grabbe et al.

  8. Research on rheological properties of micro-fine grouting cement

    Institute of Scientific and Technical Information of China (English)

    管学茂; 王雨利; 杨雷

    2003-01-01

    This article studies the influence of the fineness of cement, fly ash(FA), its composite admixture and the amount and way mixed with superplasticizer on the rheological properties of micro-fine cement(MC). By means of modern instruments and technologies (such as XRD, SEM, laser granulometer and superficial-potential apparatus etc.), the article studies the mineral compositions, the appearance character of grains, particle size distribution and superficial potential of FA and its composite materials. And through that, the reducing mechanism of FA is thoroughly analyzed. The study shows that FA and its composite admixture are excellent components which can effectively improve the rheological properties of micro-fine cement, and that the superplasticizer has a saturation point and the mixing way of it has a great influence on the rheological properties.

  9. Effects of slag fineness on durability of mortars

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In recent years, the usages of by-products and wastes in industry have become more important. The importance of the sustainable development is also of increasing. The utilizations of wastes, as mineral admixture or fine aggregate, reduce the consumption of the natural resources and improve the durability of concrete. In this study, the effect of the fineness on the high temperature and sulphate resistances of concrete mortar specimens, produced with ground granulated blast-furnace slag (GBFS)replacing cement, is investigated. The compressive and flexural strength test results for all series related to durability effects,exposing temperature and solutions, exposure times for these durability effects, slag content and fineness are discussed. Consequently, the optimum slag contents are determined for producing the sulphate and high temperature resistant mortars.

  10. Investigation on Fine Registration for SAR and Optical Image

    Directory of Open Access Journals (Sweden)

    You Hong-jian

    2014-02-01

    Full Text Available The registration of SAR and optical remote sensing image is the basise for fusing of multi-source image and comprehensive analysis. In this paper a new fine registration method for SAR and optical image is proposed. Firstly, three to four corresponding points are selected manually to realize a coarse registration that eliminates the differences in scale and rotation. Many characteristic points in the optical image are detected and the corresponding points in SAR image are extracted using normalized gradient correlations based on the different gradients by operators. An irregular triangle network is constructed using these corresponding points and each triangle region is finely registered. Finally SAR image and optical image are finely registered. Experiment and processed results demonstrate the feasibility of this method.

  11. Distortion product otoacoustic emission fine structure of symphony orchestra musicians

    DEFF Research Database (Denmark)

    Reuter, Karen; Hammershøi, Dorte

    2006-01-01

    Otoacoustic emissions (OAE) are sounds produced by the healthy inner ear. They can be measured as low-level signals in the ear canal and are used to monitor the functioning of outer hair cells. Many studies indicate that OAE might be a more sensitive measure to detect early noise-induced haring...... losses than pure-tone audiometry. The distortion product otoacoustic emission (DPOAE) fine structure is obtained when the ear is stiumulated by dual tone stimuli using a high frequency resolution. It is characterized by quasi-periodic variations across frequency, as it can be observed in the hearing...... threshold microstructure also. In this study the DPOAE fine structure is obtained for symphony orchestra musicians both for left and right ears and before and after the orchestra rehearsal. The DPOAE fine structure is analyzed in order to investigate, whether it contains more information about the state...

  12. Distortion product otoacoustic emission fine structure of symphony orchestra musicians

    DEFF Research Database (Denmark)

    Reuter, Karen; Hammershøi, Dorte

    Otoacoustic emissions (OAE) are sounds produced by the healthy inner ear. They can be measured as low-level signals in the ear canal and are used to monitor the functioning of outer hair cells.Several studies indicate that OAE might be a more sensitive measure to detect early noise-induced hearing...... losses than puretone audiometry. The distortion product otoacoustic emission (DPOAE) fine structure is obtained when the ear is stimulated by dual tone stimuli using a high frequency resolution. It is characterized by quasi-periodic variations across frequency, as it can be observed in the hearing...... threshold microstructure also. In this study DPOAE fine structures and hearing thresholds are obtained for symphony orchestra musicians both for left and right ears and before and after the orchestra rehearsal. DPOAE fine structures are analyzed with an automatic classification algorithm, which describes...

  13. An Improved Ductile Fracture Criterion for Fine-blanking Process

    Institute of Scientific and Technical Information of China (English)

    ZHAO Zhen; ZHUANG Xin-cun; XIE Xiao-long

    2008-01-01

    In order to accurately simnulate the fine-blanking process,a suitable ductile fracture is significant.So an evaluation strategy based on experimental and corresponding simulation results of tensile,compression,torsion and fine-blanking test is designed to evaluate five typical ductile fracture criteria,which are widely-used in metal forming process.The stress triaxiality and ductile damage of each test specimen are analyzed.The results show that none of these five criteria is sufficient for all tests.Furthermore,an improved fracture criterion based on Rice and Tracey model,taking the influence of both volume change and shape change of voids into account,is proposed.The characterization of this model for fine-blanking process is easily done by the tensile test and the prediction result shows good.

  14. Characterization of fine volcanic ash from explosive eruption from Sakurajima volcano, South Japan

    Science.gov (United States)

    Nanayama, F.; Furukawa, R.; Ishizuka, Y.; Yamamoto, T.; Geshi, N.; Oishi, M.

    2013-12-01

    Explosive volcanic eruptions can affect infrastructure and ecosystem by their dispersion of the volcanic particle. Characterization of volcanic particle expelled by explosive eruption is crucial for evaluating for quantitative hazard assessment by future volcanic eruption. Especially for fine volcanic ash less than 64 micron in diameter, it can disperse vast area from the source volcano and be easily remobilized by surface wind and precipitation after the deposition. As fine volcanic ash is not preserved well at the earth surface and in strata except for enormously large scale volcanic eruption. In order to quantify quantitative characteristics of fine volcanic ash particle, we sampled volcanic ash directly falling from the eruption cloud from Showa crater, the most active vent of Sakurajima volcano, just before landing on ground. We newly adopted high precision digital microscope and particle grain size analyzer to develop hazard evaluation method of fine volcanic ash particle. Field survey was performed 5 sequential days in January, 2013 to take tamper-proof volcanic ash samples directly obtained from the eruption cloud of the Sakurajima volcano using disposable paper dishes and plastic pails. Samples were taken twice a day with time-stamp in 40 localities from 2.5 km to 43 km distant from the volcano. Japan Meteorological Agency reported 16 explosive eruptions of vulcanian style occurred during our survey and we took 140 samples of volcanic ash. Grain size distribution of volcanic ash was measured by particle grain size analyzer (Mophologi G3S) detecting each grain with parameters of particle diameter (0.3 micron - 1 mm), perimeter, length, area, circularity, convexity, solidity, and intensity. Component of volcanic ash was analyzed by CCD optical microscope (VHX-2000) which can take high resolution optical image with magnifying power of 100-2500. We discriminated each volcanic ash particle by color, texture of surface, and internal structure. Grain size

  15. Theory of Solid Surfaces.

    Science.gov (United States)

    1976-05-01

    A~ —~ on 022 CAMBRIDGE UNIV (ENGLAND) CAVEND ISH LAB —. FIG 20/12 —“1THEORY OF SOLID SURFACES .(U) MAY 76 ~J C INKS ON, P W ANDERSON AF AFOSR...A~ D. ~ tLC .7~ ~~~~~~~ I In f or ~a t i oL O f f i c e r 111111 __________ ~~~~~~~~~~~~~~~ _________________ - -ii~ s ~~~~~~~~~~~~~ Abstract

  16. Atomic mechanics of solids

    CERN Document Server

    MacPherson, A K

    1990-01-01

    This volume brings together some of the presently available theoretical techniques which will be useful in the design of solid-state materials. At present, it is impossible to specify the atomic composition of a material and its macroscopic physical properties. However, the future possibilities for such a science are being laid today. This is coming about due to the development of fast, cheap computers which will be able to undertake the calculations which are necessary.Since this field of science is fairly new, it is not yet quite clear which direction of analysis will eventually prov

  17. Solid medical waste

    DEFF Research Database (Denmark)

    Udofia, Emilia Asuquo; Gulis, Gabriel; Fobil, Julius

    2017-01-01

    BACKGROUND: Solid medical waste (SMW) in households is perceived to pose minimal risks to the public compared to SMW generated from healthcare facilities. While waste from healthcare facilities is subject to recommended safety measures to minimize risks to human health and the environment, similar......-demographic characteristics, medication related practices, the belief that one is at risk of diseases associated with SMW, SMW disposal practices and reported harm associated with SMW at home and in the community. RESULTS: Eighty percent and 89% of respondents discarded unwanted medicines and sharps in household refuse bins...

  18. Physics of solids

    CERN Document Server

    Ketterson, John B

    2016-01-01

    This comprehensive text covers the basic physics of the solid state starting at an elementary level suitable for undergraduates but then advancing, in stages, to a graduate and advanced graduate level. In addition to treating the fundamental elastic, electrical, thermal, magnetic, structural, electronic, transport, optical, mechanical and compositional properties, we also discuss topics like superfluidity and superconductivity along with special topics such as strongly correlated systems, high-temperature superconductors, the quantum Hall effects, and graphene. Particular emphasis is given to so-called first principles calculations utilizing modern density functional theory which for many systems now allow accurate calculations of the electronic, magnetic, and thermal properties.

  19. Solid state physics

    CERN Document Server

    Grosso, Giuseppe

    2013-01-01

    Solid State Physics is a textbook for students of physics, material science, chemistry, and engineering. It is the state-of-the-art presentation of the theoretical foundations and application of the quantum structure of matter and materials. This second edition provides timely coverage of the most important scientific breakthroughs of the last decade (especially in low-dimensional systems and quantum transport). It helps build readers' understanding of the newest advances in condensed matter physics with rigorous yet clear mathematics. Examples are an integral part of the text, carefully de

  20. Solid Earth: The priorities

    Science.gov (United States)

    Paquet, P.

    1991-10-01

    The European Space Agency's strategy concerning the solid Earth program is reviewed. Improvement of current knowledge of the global geopotential fields, both gravity and magnetic, was stressed as the highest priority. It was agreed that the objectives and goals of the planned Aristoteles mission correspond to this priority, and the need to realize this part of the program was stated. The interdisciplinary links of the program were identified, and it was decided that this program could make substantial contributions to research of oceans, climate and global change, atmosphere, ice and land surfaces.

  1. Solid state physics

    CERN Document Server

    Burns, Gerald

    2013-01-01

    The objective of Solid State Physics is to introduce college seniors and first-year graduate students in physics, electrical engineering, materials science, chemistry, and related areas to this diverse and fascinating field. I have attempted to present this complex subject matter in a coherent, integrated manner, emphasizing fundamental scientific ideas to give the student a strong understanding and ""feel"" for the physics and the orders of magnitude involved. The subject is varied, covering many important, sophisticated, and practical areas, which, at first, may appear unrelated but which ar

  2. Solid phase transformations II

    CERN Document Server

    Čermák, J

    2009-01-01

    This topical volume includes ten invited papers that cover selected areas of the field of solid phase transformations. The first two contributions represent a burgeoning branch; that of the computer simulation of physical phenomena. The following three articles deal with the thermodynamics of phase transformations as a basic theory for describing the phenomenology of phase changes in matter. The next paper describes the interconnections between structural stability and the electronic structure of phases. Two further articles are devoted to displacive transformations; a field where there are ma

  3. Solid state devices

    Science.gov (United States)

    1991-01-01

    The Solid State Device research program is directed toward developing innovative devices for space remote and in-situ sensing, and for data processing. Innovative devices can result from the standard structures in innovative materials such as low and high temperature superconductors, strained layer superlattices, or diamond films. Innovative devices can also result from innovative structures achieved using electron tunneling or nanolithography in standard materials. A final step is to use both innovative structures and innovative materials. A new area of emphasis is the miniaturization of sensors and instruments molded by using the techniques of electronic device fabrication to micromachine silicon into micromechanical and electromechanical sensors and actuators.

  4. Laser Cooling of Solids

    Science.gov (United States)

    2009-01-01

    observed in a range of glasses and crystals doped with Yb3+ (ZBLANP [19–22], ZBLAN [23,24], CNBZn [9,25] BIG [25, 26], KGd(WO4)2 [9], KY(WO4)2 [9], YAG [27...Yb3+-doped fluorozirconate glass ZBLAN , Phys. Rev. B 75, 144302 (2007). [40] C. W. Hoyt, Laser Cooling in Thulium-doped Solids, Ph. D. Thesis...date, optical refrigeration research has been confined to glasses and crystals doped with rare- earth elements and direct-band semiconductors such as

  5. Solid State Research.

    Science.gov (United States)

    2014-09-26

    Diadiuk, M.C. Plonko. and D.L. Hovey (to be published in AppI . Phys. Lett., January 1985). 3. CA-f. Cox. III (unpublished). 4. D. Yap and L.M. Johnson... AppI . Opt. 23. 2991 (1984). 5. L.M. Johnson and D. Yap. AppI . Opt. 23. 2988 (1984). 6. Solid State Research Report. Lincoln Laboratory, M.I.T. (1983...drift current. 21. A. Carenco, L. Menegaux, and N.T. Lenh, Appi . Phys. Lett. 40, 653 (1982). 22. F.J. Leonberger, J.P. Donnelly, and C.O. Bozler

  6. Hopping transport in solids

    CERN Document Server

    Pollak, M

    1991-01-01

    The hopping process, which differs substantially from conventional transport processes in crystals, is the central process in the transport phenomena discussed in this book. Throughout the book the term ``hopping'' is defined as the inelastic tunneling transfer of an electron between two localized electronic states centered at different locations. Such processes do not occur in conventional electronic transport in solids, since localized states are not compatible with the translational symmetry of crystals.The rapid growth of interest in hopping transport has followed in the footsteps of the

  7. Solid phase transformations

    CERN Document Server

    Čermák, J

    2008-01-01

    This special-topic book, devoted to ""Solid Phase Transformations"" , covers a broad range of phenomena which are of importance in a number of technological processes. Most commercial alloys undergo thermal treatment after casting, with the aim of imparting desired compositions and/or optimal morphologies to the component phases. In spite of the fact that the topic has lain at the center of physical metallurgy for a long time, there are numerous aspects which are wide open to potential investigative breakthroughs. Materials with new structures also stimulate research in the field, as well as n

  8. Fine needle aspiration cytology of palpable supraclavicular lymph nodes

    Directory of Open Access Journals (Sweden)

    RC Adhikari

    2011-03-01

    Full Text Available Background: Fine needle aspiration cytology as a first line of investigation has assumed importance in diagnosing a variety of disease process. The aim of this study was to assess the diagnostic value of fine needle aspiration cytology in the evaluation of palpable supraclavicular lymph nodes. Materials and methods: This was a retrospective study of fine needle aspiration cytology of palpable supraclavicular lymph node done between January 1, 2007 and December 31, 2009. Fine needle aspiration cytology was performed on 149 patients (49 cases at Om Hospital & Research Centre and 100 cases at Tribhuvan University Teaching Hospital. Results: The right supraclavicular lymph node was enlarged in 55% cases, while the left supraclavicular lymph node alone was palpable in 40.3% cases and in 7 of 149 (4.7% cases, bilateral supraclavicular lymph nodes were palpable. Cytological diagnoses were categorized as reactive (8.7%, tuberculosis (41.6%, lymphoma (4.8% and metastasis (44.9%. Of a total of 74 cases of malignancy, 90.5% were non-lymphoid and 9.5% were lymphoid (5 Non-Hodgkin lymphoma and 2 Hodgkin lymphoma. Of the 67 cases of metastatic disease, three major types of malignancy found in supraclavicular lymph nodes were Squamous cell carcinoma (28 cases, adenocarcinoma (21 cases and others (small cell carcinoma, papillary thyroid carcinoma etc. Adenocarcinoma tended to metastasize to the left supraclavicular lymph node. Lung was the most common primary site (43.3%, followed by stomach, ovary, breast and larynx. However, in 28.4% cases, no primary site was found. Conclusion: The fine needle aspiration cytology can be used as a first line investigation in the evaluation of supraclavicular lymphadenopathy due to its low cost, simplicity and minimal invasiveness. Keywords: Supraclavicular lymph node; Fine needle aspiration cytology; Metastasis DOI: 10.3126/jpn.v1i1.4441 Journal of Pathology of Nepal (2011 Vol.1, 8-12  

  9. Enhancement of dissolution of Telmisartan through use of solid dispersion technique surface solid dispersion

    Directory of Open Access Journals (Sweden)

    Bhumika Patel

    2012-01-01

    Full Text Available The present study was aimed to increase the solubility of the poorly water soluble drug Telmisartan by using Surface solid dispersion (SSD made of polymers like Poloxamer 407, PEG 6000 by Solvent evaporation method. The drug was solubilized by surfactants and/or polymers then adsorbed onto the surface of extremely fine carriers to increase its surface area and to form the SSD which give the more Surface area for absorption of the drug. A 2 2 full factorial design was used to investigate for each carrier the joint influence of formulation variables: Amount of carrier and adsorbent. Saturation solubility studies shows the improvement in solubility of drug batch SSD 8 give more solubility improvement than the other batch, in-vitro dissolution of pure drug, physical mixtures and SSDs were carried out in that SSDs were found to be effective in increasing the dissolution rate of Telmisartan in form of SSD when compared to pure drug. Also FT-IR spectroscopy, differential scanning calorimetry and X-ray diffractometry studies were carried out in order to characterize the drug and Surface solid dispersion. Furthermore, both DSC and X-ray diffraction showed a decrease in the melting enthalpy and reduced drug crystallinity consequently in SSDs. However, infrared spectroscopy revealed no drug interactions with the carriers.

  10. Elemental balance of SRF production process: solid recovered fuel produced from municipal solid waste.

    Science.gov (United States)

    Nasrullah, Muhammad; Vainikka, Pasi; Hannula, Janne; Hurme, Markku; Oinas, Pekka

    2016-01-01

    In the production of solid recovered fuel (SRF), certain waste components have excessive influence on the quality of product. The proportion of rubber, plastic (hard) and certain textiles was found to be critical as to the elemental quality of SRF. The mass flow of rubber, plastic (hard) and textiles (to certain extent, especially synthetic textile) components from input waste stream into the output streams of SRF production was found to play the decisive role in defining the elemental quality of SRF. This paper presents the mass flow of polluting and potentially toxic elements (PTEs) in SRF production. The SRF was produced from municipal solid waste (MSW) through mechanical treatment (MT). The results showed that of the total input chlorine content to process, 55% was found in the SRF and 30% in reject material. Of the total input arsenic content, 30% was found in the SRF and 45% in fine fraction. In case of cadmium, lead and mercury, of their total input content to the process, 62%, 38% and 30%, respectively, was found in the SRF. Among the components of MSW, rubber material was identified as potential source of chlorine, containing 8.0 wt.% of chlorine. Plastic (hard) and textile components contained 1.6 and 1.1. wt.% of chlorine, respectively. Plastic (hard) contained higher lead and cadmium content compared with other waste components, i.e. 500 mg kg(-1) and 9.0 mg kg(-1), respectively.

  11. Semi-solid thixo casting structure of aluminum alloy and relevant assistant analysis with the help of computer simulation

    Institute of Scientific and Technical Information of China (English)

    Yi-tao YANG; Jian-fu WANG; Meng CHEN; Heng-hua ZHANG; Guang-jie SHAO

    2008-01-01

    The relationship between structure morphology of semi-solid aluminum alloy die-casting sample and filling condition was studied. By systematical structure analysis and computer simulation of the filling process, the quant-itative relationship between microscopic morphology (such as solid fraction, grain size and shape) and formation state was studied. The results showed that the billet microstruc-ture must have fine and round grains for the die-casting of complex shapes. It is necessary to optimize injection speeds to escape the non-uniform distribution of the solid fraction in complex and changeable mold cavity.

  12. Preparation of semi-solid billet of magnesium alloy and its thixoforming

    Institute of Scientific and Technical Information of China (English)

    JIANG Ju-fu; LUO Shou-jing

    2007-01-01

    Preparation of semi-solid billet of magnesium alloy and thixoforming was investigated by applying equal channel angular extrusion to magnesium alloy. The results show that mechanical properties of AZ91D alloy at room temperature, such as yield strength(YS), ultimate tensile strength(UTS) and elongation, are enhanced greatly by four-pass equal channel angular extrusion(ECAE) at 573 K and microstructure of AZ91D alloy is refined to the average grain size of 20 μm. Through using ECAE as strain induced step in SIMA and completing melt activated step by semi-solid isothermal treatment, semi-solid billet with fine spheroidal grains of 25 μm can be prepared successfully. Compared with common SIMA, thixoformed satellite angle frame components using semi-solid billet prepared by new SIMA have higher mechanical properties at room temperature and high temperature of 373 K.

  13. Development of a semi-solid metal processing technique for aluminium casting applications

    Directory of Open Access Journals (Sweden)

    Sangop Thanabumrungkul

    2008-03-01

    Full Text Available A semi-solid metal processing technique has been invented and is being developed for aluminium casting applications in Thailand. The technique uses fine gas bubbles to create convection necessary for modifying grain structure. Semi-solid metal processing of three aluminium alloys, A356, Al-4.4%Cu, and ADC12, was investigated. Results show that the novel technique successfully modified A356 and Al-4.4%Cu to become semi-solid slurry with solid fractions up to about 50%. Current developments show a feasibility of applying this technique with gravity casting and the capability to prepare semisolid slurry up to 2 kg of aluminium alloys for industrial production.

  14. Solids mixing in bubbling fluidized beds: CFD-based analysis of Bubble Dynamics and Time Scales

    Science.gov (United States)

    Bakshi, Akhilesh; Altantzis, Christos; Ghoniem, Ahmed

    2016-11-01

    In bubbling fluidized bed reactors, solids mixing is critical because it directly affects fuel segregation and residence time. However, there continues to be a lack of understanding because (a) most diagnostic techniques are only feasible in lab-scale setups and (b) the dynamics are sensitive to the operating conditions. Thus, quantitative estimates of mixing (e.g., dispersion coefficient, mixing indices) often span orders of magnitude although it is well accepted that the micro-mixing and gross circulation of solid particles is driven by bubble motion. To quantify this dependence, solids mixing is investigated using fine-grid 3D CFD simulations of a large 50 cm diameter fluidized bed. Detailed diagnostics of the computed flow-field data are performed using MS3DATA, a tool that we developed to detect and track bubbles, and the solids motion is correlated with the spatial and size distribution of bubbles. This study will be useful for quantifying mixing at commercial scales.

  15. Local Structure and Short-Range Order in a NiCoCr Solid Solution Alloy

    Science.gov (United States)

    Zhang, F. X.; Zhao, Shijun; Jin, Ke; Xue, H.; Velisa, G.; Bei, H.; Huang, R.; Ko, J. Y. P.; Pagan, D. C.; Neuefeind, J. C.; Weber, W. J.; Zhang, Yanwen

    2017-05-01

    Multielement solid solution alloys are intrinsically disordered on the atomic scale, and many of their advanced properties originate from the local structural characteristics. The local structure of a NiCoCr solid solution alloy is measured with x-ray or neutron total scattering and extended x-ray absorption fine structure (EXAFS) techniques. The atomic pair distribution function analysis does not exhibit an observable structural distortion. However, an EXAFS analysis suggests that the Cr atoms are favorably bonded with Ni and Co in the solid solution alloys. This short-range order (SRO) may make an important contribution to the low values of the electrical and thermal conductivities of the Cr-alloyed solid solutions. In addition, an EXAFS analysis of Ni ion irradiated samples reveals that the degree of SRO in NiCoCr alloys is enhanced after irradiation.

  16. Effect of yttrium on the microstructure of a semi-solid A356 Al alloy

    Institute of Scientific and Technical Information of China (English)

    LIU Zheng; HU Yongmei

    2008-01-01

    The semi-solid slurry of an A356 Al alloy,which was grain-freed by yttrium,was manufactured by low temperature pouring.The effects of grain-refining on the morphology and the grain size of the primary α phase in the semi-solid A356 Al alloy were researched.The results indicate that the semi-solid A356 Al alloy with particle-like and rosette-like primary α-Al can be prepared by low temperature pouring from a liquid grain-refined A356 alloy.The grain size and particle morphology of primary α-Al in the A356 Al alloy are markedly improved by the addition of 0.5 wt.% Y.The fining mechanism of Y on the morphology and grain size of the primary α-Al in the semi-solid A356 Al alloy was delved.

  17. Nanoporous oxidic solids: the confluence of heterogeneous and homogeneous catalysis.

    Science.gov (United States)

    Thomas, John Meurig; Hernandez-Garrido, Juan Carlos; Raja, Robert; Bell, Robert G

    2009-04-28

    The several factors that render certain kinds of nanoporous oxidic solids valuable for the design of a wide range of new heterogeneous catalysts are outlined and exemplified. These factors include: (i), their relative ease of preparation, when both mesoporous siliceous frameworks (ca. 20 to 250 A diameter pores) and microporous framework-substituted aluminophosphates (ca. 4 to 14 A diameter pores) can be tailored to suit particular catalytic needs according to whether regiospecific or enantio- or shape-selective conversions are the goal; (ii), the enormous internal (three-dimensional) areas that these nanoporous solids possess (typically 10(3) m(2) g(-1)) and the consequential ease of access of reactants through the internal pores of the solids; (iii), the ability, by judicious solid-state preparative methods to assemble spatially isolated, single-site active centres at the internal surfaces of these open-structure solids, thereby making the heterogeneous catalyst simulate the characteristic features of homogenous and enzymatic catalysts; (iv), the wide variety of in situ, time-resolved and ex situ experimental techniques, coupled with computational methods, that can pin-point the precise structure of the active site under operating conditions and facilitate the formulation of reaction intermediates and mechanisms. Varieties of catalysts are described for the synthesis (often under environmentally benign and solvent-free conditions) of a wide range of organic materials including commodity chemicals (such as adipic and terephthalic acid), fine and pharmaceutical chemicals (e.g. vitamin B(3)), alkenes, epoxides, and for the photocatalytic preferential destruction of carbon monoxide in the presence of hydrogen. Nanoporous oxidic solids are ideal materials to investigate the phenomenology of catalysis because, in many of them, little distinction exists between a model and a real catalyst.

  18. A hazard to health? Fine particles arouse worldwide interest

    Energy Technology Data Exchange (ETDEWEB)

    Karas, J.; Oesch, P.

    1998-07-01

    The most recent studies show that particles contained in the air that we breathe may have harmful effects on the health of asthmatics, children and old people in particular. Particle material found in ambient air is formed by emissions resulting from traffic, industry and other use of fuels. Nature`s own sources also have a significant effect on particle concentrations. The mechanisms by which fine particles may produce negative health effects are so far unknown. At present it is therefore impossible to assess the effects of emissions of fine particles resulting, for instance, from the use of fossil fuels

  19. Possibilities of raising the rate of fine coal flotation

    Energy Technology Data Exchange (ETDEWEB)

    Rubinstein, J.B.; Molchanov, A.E.; Chanturiya, V.A.; Guzenko, A.I. [Institute of Solid Fossil Fuels Preparation, Moscow (Russian Federation). Department of Flotation Equipment and Technological Processes Optimization

    1995-08-01

    The physical and chemical properties of coal particles change after fine grinding. A series of tests with narrow size fractions shows their floatability and the effect of fines content on the flotation response. Floatability distribution functions obtained using different reagents show that the flocculation-flotation method and flotation columns are highly efficient for upgrading coal. The methods include selective coagulation, selective flocculation, and oil agglomeration. For the flocculation-flotation process using latex (200-300 g/t), the concentrate ash was reduced by 2-3 percent, while tailings ash increased by 6-8 percent compared to conventional flotation. 11 refs., 7 figs., 2 tabs.

  20. Advanced froth flotation techniques for fine coal cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, R.H.; Luttrell, G.H. [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States)

    1994-12-31

    Advanced column flotation cells offer many potential advantages for the treatment of fine coal. The most important of these is the ability to achieve high separation efficiencies using only a single stage of processing. Unfortunately, industrial flotation columns often suffer from poor recovery, low throughput and high maintenance requirements as compared to mechanically-agitated conventional cells. These problems can usually be attributed to poorly-designed air sparging systems. This article examines the problems of air sparging in greater detail and offers useful guidelines for designing bubble generators for industrial flotation columns. The application of these principles in the design of a successful advanced fine coal flotation circuit is also presented.

  1. Le strutture ecclesiastiche a Firenze a fine Settecento

    Directory of Open Access Journals (Sweden)

    Pietro Domenico Giovannoni

    2014-04-01

    Full Text Available Il saggio ricostruisce il quadro generale delle strutture ecclesiastiche della città di Firenze alla fine del XVIII secolo: la rete parrocchiale, il ruolo del Capitolo del Duomo e quello della Basilica di San Lorenzo, la presenza di monasteri e conventi di regolari maschili e femminili ed infine le numerose compagnie laicali. Dall’analisi emerge come ancora a fine Settecento le istituzioni ecclesiastiche cittadine fossero fortemente legate alla struttura sociale della città, agli interessi ed alle strategie economiche e di prestigio sociale messe in opera dai diversi ceti, dalla aristocazia ai ceti produttivi degli artigiani.

  2. On the MSSM Higgsino mass and fine tuning

    CERN Document Server

    Ross, Graham G.

    2016-08-10

    It is often argued that low fine tuning in the MSSM necessarily requires a rather light Higgsino. In this note we show that this need not be the case when a more complete set of soft SUSY breaking mass terms are included. In particular an Higgsino mass term, that correlates the $\\mu-$term contribution with the soft SUSY-breaking Higgsino masses, significantly reduces the fine tuning even for Higgsinos in the TeV mass range where its relic abundance means it can make up all the dark matter.

  3. On the MSSM Higgsino mass and fine tuning

    Science.gov (United States)

    Ross, Graham G.; Schmidt-Hoberg, Kai; Staub, Florian

    2016-08-01

    It is often argued that low fine tuning in the MSSM necessarily requires a rather light Higgsino. In this note we show that this need not be the case when a more complete set of soft SUSY breaking mass terms are included. In particular an Higgsino mass term, that correlates the μ-term contribution with the soft SUSY-breaking Higgsino masses, significantly reduces the fine tuning even for Higgsinos in the TeV mass range where its relic abundance means it can make up all the dark matter.

  4. Fine Dust in Augmented Reality: Creating Public Service Announcement

    Directory of Open Access Journals (Sweden)

    Eugene Kim

    2014-11-01

    Full Text Available This study discusses how to create a public service announcement about fine dust using AR technology. „Aurasma,‟ a free mobile app, was used to produce the PSA. The PSA mainly consists of four parts, a trigger image, a short animation, an interactive menu, and other media which provide additional information about fine dust as users press the menu buttons. This study also surveys the user‟s preference on a PSA using AR technology and its educational effectiveness.

  5. Study of Biomass Calcite as Fine Aggregate of Concrete

    Institute of Scientific and Technical Information of China (English)

    WANG Jian; YU Yan

    2012-01-01

    The possibility of using crushed oyster shell to partly replace the fine aggregate of concrete was evaluated. The compressive strength and slump of concrete mixture with different amount of crushed oyster shell were tested and thus the appropriate dosage was determined. Additionally, the compatibility with super plasticizer and the stability in NazSO4 solution were also discussed to prove the feasibility of oyster shell as fine aggregate of concrete. The microstructure of concrete was observed with XRD and SEM techniques. This research provides the basis for the application of waste biomass calcite.

  6. Separation of Fine Particles by Using Colloidal Gas Aphrons

    Institute of Scientific and Technical Information of China (English)

    E.A.Mansur; 王运东; 戴猷元

    2004-01-01

    This paper presents a method of separation of fine particles, of the order of a few microns or less, from aqueous media by flotation using colloidal gas aphrons (CGAs) generated in aqueous solutions. More than 150 experiments were conducted to study the effects of surfactant type, surfactant concentration, CGAs flow rate, and particle concentration on the removal efficiency (fine particles of polystyrene were used as a target compound). The results indicate that CGAs, generated from cationic surfactant of hexdecyltrimethyl ammonicum bromide (HTAB) and anionic surfactant of sodium dodecylbenzne sulfonate (SDBS), are an effective method for the separation off ine particles of polystyrene from wastewater. The flotation yields are higher than 97%.

  7. A FINE GRANULAR JOINT SOURCE CHANNEL CODING METHOD

    Institute of Scientific and Technical Information of China (English)

    ZhuoLi; ShenLanusun

    2003-01-01

    An improved FGS (Fine Granular Scalability) coding method is proposed in this letter,which is based on human visual characteristics.This method adjusts FGS coding frame rate according to the evaluation of video sequences so as to improve the coding efficiency and subject perceived quality of reconstructed images.Finally,a fine granular joint source channel coding is proposed based on the source coding method,which not only utilizes the network resources efficiently,but guarantees the reliable transmission of video information.

  8. On the MSSM Higgsino mass and fine tuning

    Energy Technology Data Exchange (ETDEWEB)

    Ross, Graham G. [Oxford Univ. (United Kingdom). Rudof Peierls Centre for Theoretical Physics; Schmidt-Hoberg, Kai [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Staub, Florian [CERN, Geneva (Switzerland). Theoretical Physics Dept.

    2016-03-15

    It is often argued that low fine tuning in the MSSM necessarily requires a rather light Higgsino. In this note we show that this need not be the case when a more complete set of soft SUSY breaking mass terms are included. In particular an Higgsino mass term, that correlates the μ-term contribution with the soft SUSY-breaking Higgsino masses, significantly reduces the fine tuning even for Higgsinos in the TeV mass range where its relic abundance means it can make up all the dark matter.

  9. On the MSSM Higgsino mass and fine tuning

    Energy Technology Data Exchange (ETDEWEB)

    Ross, Graham G., E-mail: g.ross1@physics.ox.ac.uk [Rudolf Peierls Centre for Theoretical Physics, University of Oxford, 1 Keble Road, Oxford OX1 3NP (United Kingdom); Schmidt-Hoberg, Kai, E-mail: kai.schmidt-hoberg@desy.de [Deutsches Elektronen-Synchrotron DESY, Notkestraße 85, D-22607 Hamburg (Germany); Staub, Florian, E-mail: florian.staub@cern.ch [Theoretical Physics Department, CERN, Geneva (Switzerland)

    2016-08-10

    It is often argued that low fine tuning in the MSSM necessarily requires a rather light Higgsino. In this note we show that this need not be the case when a more complete set of soft SUSY breaking mass terms are included. In particular an Higgsino mass term, that correlates the μ-term contribution with the soft SUSY-breaking Higgsino masses, significantly reduces the fine tuning even for Higgsinos in the TeV mass range where its relic abundance means it can make up all the dark matter.

  10. Fine structure of fields in 2D photonic crystal waveguides

    DEFF Research Database (Denmark)

    Lavrinenko, Andrei; Volkov, V. S.; Bozhevolnyi, S. I.

    2006-01-01

    We resolve fine structure of fields in a single-row missing photonic crystal waveguide by finite-difference time-domain modelling and SNOM measurements. Both linear dispersion and slow-light regimes in proximity of the cutoff are addressed in the analysis.......We resolve fine structure of fields in a single-row missing photonic crystal waveguide by finite-difference time-domain modelling and SNOM measurements. Both linear dispersion and slow-light regimes in proximity of the cutoff are addressed in the analysis....

  11. Effects of processing parameters on microstructure of semi-solid magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    In this paper, the effects of pouring temperature of magnesium melt, preheating temperature of the barrel of the screw mixer, and shear rate on the solidified microstructures of semi-solid slurry were investigated by a mechanical stirring semi-solid process. The appropriate processing parameters of slurry preparation were obtained, and the mold filling ability of semi-solid slurry for thin-walled casting was examined. Results indicate that the solid volume fraction of non-dendritic microstructure increases with a decrease in pouring temperature of magnesium melt and the barrel preheating temperature of the screw mixer. Also the grain size of primary α-phase is reduced. Furthermore, the solid volume fraction of semi-solid nondendritic structure decreases with an increase of shear rate. The fine and round granular microstructure with 30 ~50 μm in size of semi-solid AZ91D magnesium alloy was presented. Finally, a 1.0 mm thin-walled casting with a clear contour and good soundness was successfully made by semi-solid rheo-diecasting.

  12. Effects of processing parameters on microstructure of semi-solid magnesium alloy

    Directory of Open Access Journals (Sweden)

    Shusen WU

    2004-08-01

    Full Text Available In this paper, the effects of pouring temperature of magnesium melt, preheating temperature of the barrel of the screw mixer, and shear rate on the solidified microstructures of semi-solid slurry were investigated by a mechanical stirring semi-solid process. The appropriate processing parameters of slurry preparation were obtained, and the mold filling ability of semi-solid slurry for thin-walled casting was examined. Results indicate that the solid volume fraction of non-dendritic mi-crostructure increases with a decrease in pouring temperature of magnesium melt and the barrel preheating temperature of the screw mixer. Also the grain size of primary a-phase is reduced. Furthermore, the solid volume fraction of semi-solid non-dendritic structure decreases with an increase of shear rate. The fine and round granular microstructure with 30一50 Nm insize of semi-solid AZ91D magnesium alloy was presented. Finally, a 1.0 mm thin-walled casting with a clear contour and good soundness was successfully made by semi-solid rheo-diecasting.

  13. SURFACE SIZING AND LOW SOLIDS CONTENT COATING TO IMPROVE QUALITY OF PAPER

    Institute of Scientific and Technical Information of China (English)

    Fei Yang; Chuanshan Zhao

    2004-01-01

    Surface sizing can improve the surface performances of paper. In this article we used surfacing sizing and ultra fine talcum powder to improve the quality of base paper. The results showed that the optimal formulation is: sodium hexametaphosphate 0.4 parts,PC-01 25 parts and 100 parts ultra fine talcum powder. The solids content of coating is 18%. Surface sizing and low solids coating can improve brightness,opacity, IGT Pick resistance, and breaking length which were improved by 3.4%, 6.5%, 2.07m/sec and 700m separately than uncoated paper respectively. K and N ink absorption value was reduced from 62.1 to 34.6. The method can be used to produce base paper for art paper and ultra low weight coated paper (ULWC). It can reduce the cost of art paper.

  14. Phase coexistence in ferroelectric solid solutions: Formation of monoclinic phase with enhanced piezoelectricity

    Directory of Open Access Journals (Sweden)

    Xiaoyan Lu

    2016-10-01

    Full Text Available Phase morphology and corresponding piezoelectricity in ferroelectric solid solutions were studied by using a phenomenological theory with the consideration of phase coexistence. Results have shown that phases with similar energy potentials can coexist, thus induce interfacial stresses which lead to the formation of adaptive monoclinic phases. A new tetragonal-like monoclinic to rhombohedral-like monoclinic phase transition was predicted in a shear stress state. Enhanced piezoelectricity can be achieved by manipulating the stress state close to a critical stress field. Phase coexistence is universal in ferroelectric solid solutions and may provide a way to optimize ultra-fine structures and proper stress states to achieve ultrahigh piezoelectricity.

  15. Researches on the Structure and Properties of Mullite Solid Solution Made from Industrial Waste

    Institute of Scientific and Technical Information of China (English)

    RUAN Yu-Zhong; YU Yan; WU Ren-Ping

    2006-01-01

    The waste slag from aluminum profile factory and silicon fine powder from ferroalloy factory were utilized as the main raw materials to synthesize mullite solid solution Al4+2xSi2-xO10-x/2, whose defect formation mechanism, crystalline phase composition, crystal cell parameters, microstructures and morphologies were characterized in detail by XRD and SEM. The results show that because of the ultrafine particle size of the materials, the content of mullite solid solution synthesized by this method is higher than that by regular method.

  16. Solid Pseudopapillary Neoplasm of the Pancreas in Young Male Patients: Three Case Reports

    Directory of Open Access Journals (Sweden)

    Akira Aso

    2017-01-01

    Full Text Available A preoperative diagnosis of solid pseudopapillary neoplasms (SPNs in young male patients is difficult to achieve using radiological images. We herein present three cases of young male patients with relatively small SPNs. Endoscopic ultrasound (EUS showed well-encapsulated, smooth-surfaced, heterogeneous solid lesions in all patients, and all preoperative diagnoses were achieved by EUS-guided fine needle aspiration (EUS-FNA. The final pathological diagnosis after surgery was an SPN with a Ki-67 labeling index of <2%. SPNs should be considered even in young male patients. EUS with EUS-FNA could be a useful diagnostic modality for SPNs even in young male patients.

  17. Distribution of Dechlorinating Bacteria between the Aqueous and Solid Phases

    Science.gov (United States)

    Cápiro, N. L.; Hatt, J. K.; Wang, Y.; Loeffler, F. E.; Pennell, K. D.

    2010-12-01

    Microbial monitoring of aquifers relies on nucleic acid biomarker analysis, which is typically performed with biomass recovered from groundwater samples; however, it is unclear what fraction of the target population(s) is associated with groundwater (i.e., planktonic cells) or is attached to solid phases (i.e., biofilms). Understanding how the titer of target organism(s) in groundwater correlates with the true cell titers of the target organism in the aquifer (i.e., planktonic plus attached cells) is critical for a meaningful interpretation of the data, the prediction of bioremediation performance, and the implementation of site management strategies. To evaluate the distribution of active cells between resident solid phase and the aqueous phase, one-dimensional columns were packed under water-saturated conditions with Bio-Dechlor INOCULUM, a PCE-to ethene-dechlorinating bacterial consortium containing both multiple Dehalococcoides (Dhc) strains and Geobacter lovleyi strain SZ (GeoSZ). The columns were packed with two distinct solid matrices: a low organic content sandy Federal Fine Ottawa soil or Appling soil with higher organic matter content. Influent reduced mineral salts medium supplied at a groundwater pore-water velocity of 0.3 m/day contained both 10 mM lactate as electron donor and 0.33 mM PCE as electron acceptor. Routine collection of biomass from column side ports and effluent samples measured the titers of target cells in the aqueous phase and determined when steady state conditions had been reached. A second set of column experiments evaluated delivery and filtration effects by the solid matrix (i.e., Federal Fine Ottawa sand versus Appling soil) under the same conditions except that electron donor or acceptor were omitted (no growth conditions). Quantitative real-time PCR (qPCR) analysis using Dhc and GeoSZ 16S rRNA gene-targeted primer and probe sets determined the planktonic cell counts, and destructive sampling of the columns allowed measurement

  18. Differential Profile of Ultrasound Findings Associated with Malignancy in Mixed and Solid Thyroid Nodules in an Elderly Female Population

    Directory of Open Access Journals (Sweden)

    María Inés Vera

    2014-01-01

    Full Text Available Objective. Ultrasonographic characteristics are associated with thyroid malignancy. Our aim was to compare the diagnostic value of ultrasound features in the detection of thyroid malignancy in both solid and mixed nodules. Methods. We prospectively studied female patients (≥50 years referred to ultrasound-guided fine needle aspiration biopsy. Ultrasound features considered suspicious were hypoechogenicity, microcalcifications, irregular margins, high anteroposterior (AP/axial-ratio, and absent halo. Associations were separately assessed in mixed and solid nodules. Results. In a group of 504 elderly female patients (age = 69±8 years, the frequency of malignant cytology was 6%. Thirty-one percent of nodules were mixed and 60% were solid. The rate of malignant cytology was similar for mixed and solid nodules (7.4 versus 5.8%, P: 0.56. While in mixed nodules none of the ultrasound characteristics were associated with malignant cytology, in solid nodules irregular margins and microcalcifications were significant (all P<0.05. The combination of irregular margins and/or microcalcifications significantly increased the association with malignant cytology only in solid nodules (OR: 2.76 (95% CI: 1.25–6.10, P: 0.012. Conclusions. Ultrasound features were of poor diagnostic value in mixed nodules, which harbored malignant lesions as often as solid nodules. Our findings challenge the recommended minimal size for ultrasound-guided fine needle aspiration biopsy in mixed nodules.

  19. Position sensitive solid state detectors

    Energy Technology Data Exchange (ETDEWEB)

    Schnatterly, S.E.; Husk, D.

    1986-05-15

    Solid state detectors have been used for years as high quantum efficiency detectors for visible light. In this paper the use of PDA and CCD, solid state detectors, in the X-ray region will be discussed. In particular examples of data in the soft X-ray region are presented. Finally the use of phosphor coatings to enhance the sensitivity of solid state detectors is described.

  20. Fine structure of fields in 2D photonic crystal waveguides

    DEFF Research Database (Denmark)

    Lavrinenko, Andrei; Volkov, V. S.; Bozhevolnyi, S. I.

    2006-01-01

    We resolve fine structure of fields in a single-row missing photonic crystal waveguide by finite-difference time-domain modelling and SNOM measurements. Both linear dispersion and slow-light regimes in proximity of the cutoff are addressed in the analysis....

  1. [Starting with camphor--the progress of Nippon Fine Chemical].

    Science.gov (United States)

    Kimura, Osamu

    2010-01-01

    In 1918, Nippon Fine Chemical Co., Ltd. (NFC) was founded under the name, Nippon Camphor Co., Ltd. for the purpose of unifying the camphor business throughout Japan. The company manufactured purified camphor as a government-monopolized good. Camphor was used as a plasticizer for nitrocellulose, as a moth repellent, as an antimicrobial substance, as a rust inhibitor, and as an active ingredient in medicine. It was also a very important good exported in order to obtain foreign currency. Later on, after World War II and the abolition of the camphor monopoly, the company started manufacturing products related to oils and fats, including higher fatty acids, and expanded its business by developing a new field of chemical industry. In 1971 the company changed its name to Nippon Fine Chemical Co., Ltd., and made a new start as a diversified fine chemicals company. Recently, the fine chemicals division of NFC has concentrated on rather complex molecules, such as active pharmaceutical ingredients, and other chemicals. Since 2000, NFC have started to supply "Presome", precursors of liposome DDS drugs. NFC is strengthening marketing strategies in foreign countries with unique technologies and products.

  2. SOURCE SAMPLING FINE PARTICULATE MATTER: WOOD-FIRED INDUSTRIAL BOILER

    Science.gov (United States)

    The report provides a profile for a wood-fired industrial boiler equipped with a multistage electrostatic precipitator control device. Along with the profile of emissions of fine particulate matter of aerodynamic diameter of 2.5 micrometers or less (PM-2.5), data are also provide...

  3. Fine5 tantsuteater võitis Vitebskis teise preemia

    Index Scriptorium Estoniae

    2006-01-01

    22. - 26. XI Valgevenes toimunud kaasaegse koreograafia konkursil "International Festival of Modern Choreography" võitsid Laura Kvelstein ja Dmitri Kruus lühiteostega "1 spot, 2 shadows" teise preemia. Konkursi raames toimunud meistriklasse juhendas Fine5 koreograaf Tiina Ollesk

  4. Fine Tuning in Quintessence Models with Exponential Potentials

    CERN Document Server

    Rosenfeld, R; Jr., Urbano Lopes Franca; Rosenfeld, Rogerio

    2002-01-01

    We show that there still are reasonable regions of the parameter space of the simple exponential potential model for quintessence that are allowed by observational constraints. We find that the level of fine tuning that is required in this model is not too stringent.

  5. Facilitating Fine Grained Data Provenance using Temporal Data Model

    NARCIS (Netherlands)

    Huq, M.R.; Wombacher, Andreas; Apers, Peter M.G.

    2010-01-01

    E-science applications use fine grained data provenance to maintain the reproducibility of scientific results, i.e., for each processed data tuple, the source data used to process the tuple as well as the used approach is documented. Since most of the e-science applications perform on-line

  6. Fining of Red Wine Monitored by Multiple Light Scattering.

    Science.gov (United States)

    Ferrentino, Giovanna; Ramezani, Mohsen; Morozova, Ksenia; Hafner, Daniela; Pedri, Ulrich; Pixner, Konrad; Scampicchio, Matteo

    2017-07-12

    This work describes a new approach based on multiple light scattering to study red wine clarification processes. The whole spectral signal (1933 backscattering points along the length of each sample vial) were fitted by a multivariate kinetic model that was built with a three-step mechanism, implying (1) adsorption of wine colloids to fining agents, (2) aggregation into larger particles, and (3) sedimentation. Each step is characterized by a reaction rate constant. According to the first reaction, the results showed that gelatin was the most efficient fining agent, concerning the main objective, which was the clarification of the wine, and consequently the increase in its limpidity. Such a trend was also discussed in relation to the results achieved by nephelometry, total phenols, ζ-potential, color, sensory, and electronic nose analyses. Also, higher concentrations of the fining agent (from 5 to 30 g/100 L) or higher temperatures (from 10 to 20 °C) sped up the process. Finally, the advantage of using the whole spectral signal vs classical univariate approaches was demonstrated by comparing the uncertainty associated with the rate constants of the proposed kinetic model. Overall, multiple light scattering technique showed a great potential for studying fining processes compared to classical univariate approaches.

  7. Longing for Clouds - Does Beautiful Weather have to be Fine?

    Directory of Open Access Journals (Sweden)

    Mădălina Diaconu

    2016-01-01

    Full Text Available Any attempt to outline a meteorological aesthetics centered on so-called beautiful weather has to overcome several difficulties: In everyday life, the appreciation of the weather is mostly related to practical interests or reduced to the ideal of stereotypical fine weather that is conceived according to blue-sky thinking irrespective of climate diversity. Also, an aesthetics of fine weather seems, strictly speaking, to be impossible given that such weather conditions usually allow humans to focus on aspects other than weather, which contradicts the autotelic character of beauty. The unreflective equation of beautiful weather with moderately sunny weather and a cloudless sky also collides with the psychological need for variation: even living in a “paradisal” climate would be condemned to end in monotony. Finally, whereas fine weather is related in modern realistic literature to cosmic harmony and a universal natural order, contemporary literary examples show that in the age of the climate change, fine weather may be deceitful and its passive contemplation, irresponsible. This implies the necessity of a reflective aesthetic attitude on weather, as influenced by art, literature, and science, which discovers the poetics of bad weather and the wonder that underlies average weather conditions.

  8. The Appropriation of Fine Art into Contemporary Narrative Picturebooks

    Science.gov (United States)

    Serafini, Frank

    2015-01-01

    Many picturebook artists have been formally trained in specific artistic styles, movements, and techniques. These artists appropriate and transform works of fine art to varying degrees to fit the themes and designs of the stories they illustrate and publish, and to increase the significance and impact of their illustrations. The…

  9. FINE PARTICLE EXPOSURE IS ASSOCIATED WITH ALTERED VENTRICULAR REPOLARIZATION

    Science.gov (United States)

    Exposure to fine airborne particulate matter (PM2.5) has previously been associated with cardiac events, especially in older people with cardiovascular disease and in diabetics. This study examined the cardiac effects of short-term exposures to ambient PM2.5 in a prospective pane...

  10. The Fine-Tuning of the Universe for Intelligent Life

    CERN Document Server

    Barnes, Luke A

    2011-01-01

    The fine-tuning of the universe for intelligent life has received a great deal of attention in recent years, both in the philosophical and scientific literature. The claim is that in the space of possible physical laws, parameters and initial conditions, the set that permits the evolution of intelligent life is very small. I present here a review of the scientific literature, outlining cases of fine-tuning in the classic works of Carter, Carr and Rees, and Barrow and Tipler, as well as more recent work. To sharpen the discussion, the role of the antagonist will be played by Victor Stenger's recent book The Fallacy of Fine-Tuning: Why the Universe is Not Designed for Us. Stenger claims that all known fine-tuning cases can be explained without the need for a multiverse. Many of Stenger's claims will be found to be highly problematic. We will touch on such issues as the logical necessity of the laws of nature; objectivity, invariance and symmetry; theoretical physics and possible universes; entropy in cosmology;...

  11. 28 CFR 0.171 - Judgments, fines, penalties, and forfeitures.

    Science.gov (United States)

    2010-07-01

    ... OF JUSTICE Authority To Compromise and Close Civil Claims and Responsibility for Judgments, Fines... that the division will assume such enforcement responsibilities. (b) Each U.S. Attorney shall designate... section that such division will assume responsibility for enforcement of a criminal monetary penalty,...

  12. A TEM Study on the Microstructure of Fine Flaky Graphite

    DEFF Research Database (Denmark)

    Moumeni, Elham; Tiedje, Niels Skat; Horsewell, Andy

    In this investigation the microstructure of the graphite flakes in titanium alloyed cast iron is studied using electron microscopy techniques. Based on this information, growth models for the platelets in the fine graphite flakes in cast iron are considered. Detailed crystallographic analysis of ...... of the defects observed such as multiple twin boundaries and possible spiral growth configurations are required...

  13. The Heck reaction in the production of fine chemicals

    NARCIS (Netherlands)

    Vries, Johannes G. de

    2001-01-01

    An overview is given of the use of the Heck reaction for the production of fine chemicals. Five commercial products have been identified that are produced on a scale in excess of 1 ton/year. The herbicide Prosulfuron™ is produced via a Matsuda reaction of 2-sulfonatobenzenediazonium on 3,3,3-trifluo

  14. Binding energy and fine structure of the He- ion

    Institute of Scientific and Technical Information of China (English)

    ZHUO; Lin; ZHU; Jing-jing; GOU; Bing-cong

    2007-01-01

    The variational method using a multiconfiguration wavefunction is carried out on the core-excited state 1s2s2p 4P0 for helium negative ion, including mass polarization and relativistic corrections. Binding energy and fine structure are reported. The results are compared with other theoretical and experimental date in the literature.

  15. Envisioning the Future: Working toward Sustainability in Fine Art Education

    Science.gov (United States)

    Clarke, Angela; Hulbert, Shane

    2016-01-01

    Fine art education provides students with opportunities to acquire knowledge and skills to respond creatively to their experience of society and culture. Fostering creative ways of knowing, thinking and doing requires studio learning conditions that promote the exploration of embodied perceptions, material sensibilities and conceptual ideas that…

  16. Multiscale physical processes of fine sediment in an estuary

    NARCIS (Netherlands)

    Wan, Y.

    2015-01-01

    This study presented in this book investigates micro- and macro- scale physical processes of a large-scale fine sediment estuarine system with a moderate tidal range as well as a highly seasonal-varying freshwater inflow. Based on a series measured, experimented and modeled results, the research hig

  17. Fine and Gross Motor Ability in Males with ADHD

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2003-09-01

    Full Text Available Both fine and gross motor abilities were evaluated in 10-year-old males with attention deficit hyperactivity disorder (ADHD and compared to a group of control children at the School of Psychology, Curtin University of Technology, Perth, Australia.

  18. Laser phase-detector and counter for fine displacement measurement

    Science.gov (United States)

    Row, R. T.; Wang, C. P.

    A simple technique for the measurement of fine displacement has been developed. With use of an HeNe laser, an optical phase-detector, and counter, a displacement accuracy of 300 nm has been demonstrated over a range of 2 cm.

  19. Revisioning Premodern Fine Art as Popular Visual Culture

    Science.gov (United States)

    Duncum, Paul

    2014-01-01

    Employing the concept of a rhetoric of emotions, European Premodern fine art is revisioned as popular culture. From ancient times, the rhetoric of emotion was one of the principle concepts informing the theory and practice of all forms of European cultural production, including the visual arts, until it was gradually displaced during the 1700s and…

  20. Probabilistic inference of fine-grained data provenance

    NARCIS (Netherlands)

    Huq, Mohammad Rezwanul; Apers, P.M.G.; Wombacher, A.

    2012-01-01

    Decision making, process control and e-science applications process stream data, mostly produced by sensors. To control and monitor these applications, reproducibility of result is a vital requirement. However, it requires massive amount of storage space to store fine-grained provenance data especia