WorldWideScience

Sample records for extraction cssx unit

  1. Cesium Removal from Savannah River Site Radioactive Waste Using the Caustic Side Solvent Extraction (CSSX) Process

    International Nuclear Information System (INIS)

    WALKER, DARREL

    2004-01-01

    Researchers at the Savannah River Technology Center (SRTC) successfully demonstrated the Caustic-Side Solvent Extraction (CSSX) process flow sheet using a 33-stage, 2-cm centrifugal contactor apparatus in two 24-hour tests using actual high level waste. Previously, we demonstrated the solvent extraction process with actual SRS HLW supernatant solution using a non-optimized solvent formulation. Following that test, the solvent system was optimized to enhance extractant solubility in the diluent by increasing the modifier concentration. We now report results of two tests with the new and optimized solvent

  2. Examination of Organic Carryover from 2-cm Contactors to Support the Modular CSSX Unit

    International Nuclear Information System (INIS)

    Nash, Charles A.; Norato, Michael A.; Walker; D. Douglas; Pierce, Robert A.; Eubanks, Ronnye A.; Clark, James D.; Smith, Wilson M. Jr.; Crump, Stephen L.; Nelson, D. Zane; Fink, Samuel D.; Peters, Thomas B.; May, Cecil G.; Herman, David T.; Bolton, Henry L.

    2005-01-01

    A bank of four 2-cm centrifugal contactors was operated in countercurrent fashion to help address questions about organic carryover for the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). The contactors, having weirs sized for strip operation, were used to examine carryover for both strip effluent (SE) and decontaminated salt solution (DSS). Since only one bank of contactors was available in the short time frame of this work, the organic phase and only one aqueous phase were present in the flow loops at a time. Personnel maintained flowsheet-typical organic phase to aqueous phase (O:A) flow ratios when varying flow rates. Solvent from two different batches were tested with strip solution. In addition, potential mitigations of pH adjustment and coalescing media were examined. The experiment found that organic carryover after decanting averaged 220 ppm by mass with a range of 74 to 417 ppm of Isopar(reg s ign) L for strip effluent (SE)/organic solvent contacts. These values are based on measured modifier. Values were bounded by a value of 95 ppm based upon Isopar(reg s ign) L values as reported. The higher modifier-based numbers are considered more reliable at this time. Carryover of Isopar(reg s ign) L in DSS simulant averaged 77 ppm by mass with a range of 70 to 88 ppm of Isopar(reg s ign) L based on modifier content. The carryover was bounded by a value of 19 ppm based upon Isopar(reg s ign) L values as reported. More work is needed to resolve the discrepancy between modifier and Isopar(reg s ign) L values. The work did not detect organic droplets greater than 18 microns in SE. Strip output contained droplets down to 0.5 micron in size. Droplets in DSS were almost monodisperse by comparison, having a size range 4.7 +/- 1.6 micron in one test and 5.2 +/- 0.8 micron in the second demonstration. Optical microscopy provided qualitative results confirming the integrity of droplet size measurements in this work. Acidic or basic adjustments of aqueous strip

  3. Examination of Organic Carryover from 2-cm Contactors to Support the Modular CSSX Unit

    Energy Technology Data Exchange (ETDEWEB)

    Nash, Charles A.; Norato, Michael A.; Walker; D. Douglas; Pierce, Robert A.; Eubanks, Ronnye A.; Clark, James D.; Smith, Wilson M. Jr.; Crump, Stephen L.; Nelson, D. Zane; Fink, Samuel D.; Peters, Thomas B.; May, Cecil G.; Herman, David T.; Bolton, Henry L.

    2005-04-29

    A bank of four 2-cm centrifugal contactors was operated in countercurrent fashion to help address questions about organic carryover for the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). The contactors, having weirs sized for strip operation, were used to examine carryover for both strip effluent (SE) and decontaminated salt solution (DSS). Since only one bank of contactors was available in the short time frame of this work, the organic phase and only one aqueous phase were present in the flow loops at a time. Personnel maintained flowsheet-typical organic phase to aqueous phase (O:A) flow ratios when varying flow rates. Solvent from two different batches were tested with strip solution. In addition, potential mitigations of pH adjustment and coalescing media were examined. The experiment found that organic carryover after decanting averaged 220 ppm by mass with a range of 74 to 417 ppm of Isopar{reg_sign} L for strip effluent (SE)/organic solvent contacts. These values are based on measured modifier. Values were bounded by a value of 95 ppm based upon Isopar{reg_sign} L values as reported. The higher modifier-based numbers are considered more reliable at this time. Carryover of Isopar{reg_sign} L in DSS simulant averaged 77 ppm by mass with a range of 70 to 88 ppm of Isopar{reg_sign} L based on modifier content. The carryover was bounded by a value of 19 ppm based upon Isopar{reg_sign} L values as reported. More work is needed to resolve the discrepancy between modifier and Isopar{reg_sign} L values. The work did not detect organic droplets greater than 18 microns in SE. Strip output contained droplets down to 0.5 micron in size. Droplets in DSS were almost monodisperse by comparison, having a size range 4.7 +/- 1.6 micron in one test and 5.2 +/- 0.8 micron in the second demonstration. Optical microscopy provided qualitative results confirming the integrity of droplet size measurements in this work. Acidic or basic adjustments of aqueous strip solution

  4. Life Extension Program for the Modular Caustic Side Solvent Extraction Unit at Savannah River Site - 13179

    International Nuclear Information System (INIS)

    Samadi, Azadeh

    2013-01-01

    Caustic Side Solvent Extraction (CSSX) is currently used at the U.S. Department of Energy (DOE) Savannah River Site (SRS) for removal of cesium from the high-level salt-wastes stored in underground tanks. Currently, the Actinide Removal Process (ARP) and the CSSX process are deployed in the (ARP)/Modular CSSX Unit (MCU), to process salt waste for permanent disposition. The CSSX technology utilizes a multi-component organic solvent and annular centrifugal contactors to extract cesium from alkaline salt waste. The original plant was permitted for a three year design life; however, given the successful operation of the plant, a life extension program was completed to continue operations. The program included detailed engineering analyses of the life-expectancy of passive and active components, resulting in component replacement and/or maintenance and monitoring program improvements. The program also included a review of the operations and resulted in a series of operational improvements. Since the improvements have been made, an accelerated processing rate has been demonstrated. In addition, plans for instituting a next-generation solvent are in place and will enhance the decontamination factors. (author)

  5. Density Changes in the Optimized CSSX Solvent System

    Energy Technology Data Exchange (ETDEWEB)

    Lee, D.D.

    2002-11-25

    Density increases in caustic-side solvent extraction (CSSX) solvent have been observed in separate experimental programs performed by different groups of researchers. Such changes indicate a change in chemical composition. Increased density adversely affects separation of solvent from denser aqueous solutions present in the CSSX process. Identification and control of factors affecting solvent density are essential for design and operation of the centrifugal contactors. The goals of this research were to identify the factors affecting solvent density (composition) and to develop correlations between easily measured solvent properties (density and viscosity) and the chemical composition of the solvent, which will permit real-time determination and adjustment of the solvent composition. In evaporation experiments, virgin solvent was subjected to evaporation under quiescent conditions at 25, 35, and 45 C with continuously flowing dry air passing over the surface of the solvent. Density and viscosity were measured periodically, and chemical analysis was performed on the solvent samples. Chemical interaction tests were completed to determine if any chemical reaction takes place over extended contact time that changes the composition and/or physical properties. Solvent and simulant, solvent and strip solution, and solvent and wash solution were contacted continuously in agitated flasks. They were periodically sampled and the density measured (viscosity was also measured on some samples) and then submitted to the Chemical Sciences Division of Oak Ridge National Laboratory for analysis by nuclear magnetic resonance (NMR) spectrometry and high-performance liquid chromatography (HPLC) using the virgin solvent as the baseline. Chemical interaction tests showed that solvent densities and viscosities did not change appreciably during contact with simulant, strip, or wash solution. No effects on density and viscosity and no chemical changes in the solvent were noted within

  6. Analysis of cesium extracting solvent using GCMS and HPLC

    International Nuclear Information System (INIS)

    White, T.L.; Herman, C.C.; Crump, S.L.; Marinik, A.R.; Lambert, D.P.; Eibling, R.E.

    2007-01-01

    A high-level waste (HLW) remediation process scheduled to begin in 2007 at the Savannah River Site is the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). The MCU will use a hydrocarbon solvent (diluent) containing a cesium extractant, a calix[4]arene compound, to extract radioactive cesium from caustic HLW. The resulting decontaminated HLW waste or raffinate will be processed into grout at the Saltstone Production Facility (SPF). The cesium containing CSSX stream will undergo washing with dilute nitric acid followed by stripping of the cesium nitrate into a very dilute nitric acid or the strip effluent stream and the CSSX solvent will be recycled. The Defense Waste Processing Facility (DWPF) will receive the strip effluent stream and immobilize the cesium into borosilicate glass. Excess CSSX solvent carryover from the MCU creates a potential flammability problem during DWPF processing. Bench-scale DWPF process testing was performed with simulated waste to determine the fate of the CSSX solvent components. A simple high performance liquid chromatography (HPLC) method was developed to identify the modifier (which is used to increase Cs extraction and extractant solubility) and extractant within the DWPF process. The diluent and trioctylamine (which is used to suppress impurity effect and ion-pair disassociation) were determined using gas chromatography mass spectroscopy (GCMS). To close the organic balance, two types of sample preparation methods were needed. One involved extracting aqueous samples with methylene chloride or hexane, and the second was capturing the off gas of the DWPF process using carbon tubes and rinsing the tubes with carbon disulfide for analysis. This paper addresses the development of the analytical methods and the bench-scale simulated waste study results. (author)

  7. DEMONSTRATION OF THE NEXT-GENERATION CAUSTIC-SIDE SOLVENT EXTRACTION SOLVENT WITH 2-CM CENTRIGUGAL CONTRACTORS USING TANK 49H WASTE AND WASTE SIMULANT

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, R.; Peters, T.; Crowder, M.; Pak, D.; Fink, S.; Blessing, R.; Washington, A.; Caldwell, T.

    2011-11-29

    Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet using MaxCalix for the decontamination of high level waste (HLW). The demonstration was completed using a 12-stage, 2-cm centrifugal contactor apparatus at the Savannah River National Laboratory (SRNL). This represents the first CSSX process demonstration of the MaxCalix solvent system with Savannah River Site (SRS) HLW. Two tests lasting 24 and 27 hours processed non-radioactive simulated Tank 49H waste and actual Tank 49H HLW, respectively. A solvent extraction system for removal of cesium from alkaline solutions was developed utilizing a novel solvent invented at the Oak Ridge National Laboratory (ORNL). This solvent consists of a calix[4]arene-crown-6 extractant dissolved in an inert hydrocarbon matrix. A modifier is added to the solvent to enhance the extraction power of the calixarene and to prevent the formation of a third phase. An additional additive is used to improve stripping performance and to mitigate the effects of any surfactants present in the feed stream. The process that deploys this solvent system is known as Caustic Side Solvent Extraction (CSSX). The solvent system has been deployed at the Savannah River Site (SRS) in the Modular CSSX Unit (MCU) since 2008.

  8. MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT (MCU) GAMMA MONITORS SYSTEM FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Casella, V

    2005-12-15

    The Department of Energy (DOE) selected Caustic-Side Solvent Extraction (CSSX) as the preferred technology for the removal of radioactive cesium from High-Level Waste (HLW) at the Savannah River Site (SRS). Before the full-scale Salt Waste Processing Facility (SWPF) becomes operational, the Closure Business Unit (CBU) plans to process a portion of dissolved saltcake waste through a Modular CSSX Unit (MCU). This work was derived from Technical Task Request SP-TTR-2004-00013, ''Gamma Monitor for MCU''. The deliverables for this task are the hardware and software for the gamma monitors and a report summarizing the testing and acceptance of this equipment for use in the MCU. Gamma-ray monitors are required to: (1) Measure the Cs-137 concentration in the decontaminated salt solution before entering the DSS (Decontaminated Salt Solution) Hold Tank, (2) Measure the Cs-137 concentration in the strip effluent before entering the Strip Effluent Hold Tank, (3) Verify proper operation of the solvent extraction system by verifying material balance within the process (The DSS Hold Tank Cs-137 concentration will be very low and the Cs-137 concentration in the Strip Effluent Hold Tank will be fifteen times higher than the Cs-137 concentration in the Feed Tank.) Sodium iodide monitors are used to measure the Cs-137 concentration in the piping before the DSS Hold tank, while GM monitors are used for Cs-137 measurements before the Strip Effluent Hold Tank. Tungsten shields were designed using Monte Carlo calculations and fabricated to reduce the process background radiation at the detector positions. These monitors were calibrated with NIST traceable standards that were specially made to be the same as the piping being monitored. Since this gamma ray monitoring system is unique, specially designed software was written and acceptance tested by Savannah River National Laboratory personnel. The software is a LabView-based application that serves as a unified

  9. MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT (MCU) GAMMA MONITORS SYSTEM FINAL REPORT

    International Nuclear Information System (INIS)

    Casella, V

    2005-01-01

    The Department of Energy (DOE) selected Caustic-Side Solvent Extraction (CSSX) as the preferred technology for the removal of radioactive cesium from High-Level Waste (HLW) at the Savannah River Site (SRS). Before the full-scale Salt Waste Processing Facility (SWPF) becomes operational, the Closure Business Unit (CBU) plans to process a portion of dissolved saltcake waste through a Modular CSSX Unit (MCU). This work was derived from Technical Task Request SP-TTR-2004-00013, ''Gamma Monitor for MCU''. The deliverables for this task are the hardware and software for the gamma monitors and a report summarizing the testing and acceptance of this equipment for use in the MCU. Gamma-ray monitors are required to: (1) Measure the Cs-137 concentration in the decontaminated salt solution before entering the DSS (Decontaminated Salt Solution) Hold Tank, (2) Measure the Cs-137 concentration in the strip effluent before entering the Strip Effluent Hold Tank, (3) Verify proper operation of the solvent extraction system by verifying material balance within the process (The DSS Hold Tank Cs-137 concentration will be very low and the Cs-137 concentration in the Strip Effluent Hold Tank will be fifteen times higher than the Cs-137 concentration in the Feed Tank.) Sodium iodide monitors are used to measure the Cs-137 concentration in the piping before the DSS Hold tank, while GM monitors are used for Cs-137 measurements before the Strip Effluent Hold Tank. Tungsten shields were designed using Monte Carlo calculations and fabricated to reduce the process background radiation at the detector positions. These monitors were calibrated with NIST traceable standards that were specially made to be the same as the piping being monitored. Since this gamma ray monitoring system is unique, specially designed software was written and acceptance tested by Savannah River National Laboratory personnel. The software is a LabView-based application that serves as a unified interface for controlling

  10. Evaluation of the Hydraulic Performance and Mass Transfer Efficiency of the CSSX Process with the Optimized Solvent in a Single Stage of 5.5-Cm Diameter Centrifugal Contactor

    International Nuclear Information System (INIS)

    Law, J.D.; Tillotson, R.D.; Todd, T.A.

    2002-01-01

    The Caustic-Side Solvent Extraction (CSSX) process has been selected for the separation of cesium from Savannah River Site high-level waste. The solvent composition used in the CSSX process was recently optimized so that the solvent is no longer supersaturated with respect to the calixarene crown ether extractant. Hydraulic performance and mass transfer efficiency testing of a single stage of 5.5-cm ORNL-designed centrifugal contactor has been performed for the CSSX process with the optimized solvent. Maximum throughputs of the 5.5-cm centrifugal contactor, as a function of contactor rotor speed, have been measured for the extraction, scrub, strip, and wash sections of the CSSX flowsheet at the baseline organic/aqueous flow ratios (O/A) of the process, as well as at O/A's 20% higher and 20% lower than the baseline. Maximum throughputs are comparable to the design throughput of the contactor, as well as with throughputs obtained previously in a 5-cm centrifugal contactor with the non-optimized CSSX solvent formulation. The 20% variation in O/A had minimal effect on contactor throughput. Additionally, mass transfer efficiencies have been determined for the extraction and strip sections of the flowsheet. Efficiencies were lower than the process goal of greater than or equal to 80%, ranging from 72 to 75% for the extraction section and from 36 to 60% in the strip section. Increasing the mixing intensity and/or the solution level in the mixing zone of the centrifugal contactor (residence time) could potentially increase efficiencies. Several methods are available to accomplish this including (1) increasing the size of the opening in the bottom of the rotor, resulting in a contactor which is partially pumping instead of fully pumping, (2) decreasing the number of vanes in the contactor, (3) increasing the vane height, or (4) adding vanes on the rotor and baffles on the housing of the contactor. The low efficiency results obtained stress the importance of proper design of

  11. Defense Waste Processing Facility (DWPF), Modular CSSX Unit (CSSX), and Waste Transfer Line System of Salt Processing Program (U)

    International Nuclear Information System (INIS)

    CHANG, ROBERT

    2006-01-01

    All of the waste streams from ARP, MCU, and SWPF processes will be sent to DWPF for vitrification. The impact these new waste streams will have on DWPF's ability to meet its canister production goal and its ability to support the Salt Processing Program (ARP, MCU, and SWPF) throughput needed to be evaluated. DWPF Engineering and Operations requested OBU Systems Engineering to evaluate DWPF operations and determine how the process could be optimized. The ultimate goal will be to evaluate all of the Liquid Radioactive Waste (LRW) System by developing process modules to cover all facilities/projects which are relevant to the LRW Program and to link the modules together to: (1) study the interfaces issues, (2) identify bottlenecks, and (3) determine the most cost effective way to eliminate them. The results from the evaluation can be used to assist DWPF in identifying improvement opportunities, to assist CBU in LRW strategic planning/tank space management, and to determine the project completion date for the Salt Processing Program

  12. Inline Monitors for Measuring Cs-137 in the SRS Caustic Side Solvent Extraction Process

    Energy Technology Data Exchange (ETDEWEB)

    Casella, V

    2006-04-24

    The Department of Energy (DOE) selected Caustic-Side Solvent Extraction (CSSX) as the preferred technology for the removal of radioactive cesium from High-Level Waste (HLW) at the Savannah River Site (SRS). Before the full-scale Salt Waste Processing Facility (SWPF) becomes operational, a portion of dissolved saltcake waste will be processed through a Modular CSSX Unit (MCU). The MCU employs the CSSX process, a continuous process that uses a novel solvent to extract cesium from waste and concentrate it in dilute nitric acid. Of primary concern is Cs-137 which makes the solution highly radioactive. Since the MCU does not have the capacity to wait for sample results while continuing to operate, the Waste Acceptance Strategy is to perform inline analyses. Gamma-ray monitors are used to: measure the Cs-137 concentration in the decontaminated salt solution (DSS) before entering the DSS Hold Tank; measure the Cs-137 concentration in the strip effluent (SE) before entering the SE Hold Tank; and verify proper operation of the solvent extraction system by verifying material balance within the process. Since this gamma ray monitoring system application is unique, specially designed shielding was developed and software was written and acceptance tested by Savannah River National Laboratory (SRNL) personnel. The software is a LabView-based application that serves as a unified interface for controlling the monitor hardware and communicating with the host Distributed Control System. This paper presents the design, fabrication and implementation of this monitoring system.

  13. Next Generation Solvent - Materials Compatibility With Polymer Components Within Modular Caustic-Side Solvent Extraction Unit (Final Report)

    International Nuclear Information System (INIS)

    Fondeur, F.; Peters, T.; Fink, S.

    2012-01-01

    The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. The technical effort is collaboration between Oak Ridge National Laboratory (ORNL), Savannah River National Laboratory (SRNL), and Argonne National Laboratory. The first deployment target for the technology is within the Modular Caustic-Side Solvent Extraction Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the facility. This report provides the data from exposing these polymers to the Next Generation Solvent (NGS). The test was conducted over six months. An assessment of the dimensional stability of polymers present in MCU (i.e., PEEK, Grafoil, Tefzel and Isolast) in the modified NGS (where the concentration of LIX(reg s ign)79 and MaxCalix was varied systematically) showed that LIX(reg s ign)79 selectively affected Tefzel and its different grades (by an increase in size and lowering its density). The copolymer structure of Tefzel and possibly its porosity allows for the easier diffusion of LIX(reg s ign)79. Tefzel is used as the seat material in some of the valves at MCU. Long term exposure to LIX(reg s ign)79, may make the valves hard to operate over time due to the seat material (Tefzel) increasing in size. However, since the physical changes of Tefzel in the improved solvent are comparable to the changes in the CSSX baseline solvent, no design changes are needed with respect to the Tefzel seating material. PEEK, Grafoil and Isolast were not affected by LIX(reg s ign)79 and MaxCalix within six months of exposure. The initial rapid weight gain observed in every polymer is assigned to the finite and

  14. NEXT GENERATION SOLVENT-MATERIALS COMPATIBILITY WITH POLYMER COMPONENTS WITHIN MODULAR CAUSTIC-SIDE SOLVENT EXTRACTION UNIT (FINAL REPORT)

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F.; Peters, T.; Fink, S.

    2012-01-17

    The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. The technical effort is collaboration between Oak Ridge National Laboratory (ORNL), Savannah River National Laboratory (SRNL), and Argonne National Laboratory. The first deployment target for the technology is within the Modular Caustic-Side Solvent Extraction Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the facility. This report provides the data from exposing these polymers to the Next Generation Solvent (NGS). The test was conducted over six months. An assessment of the dimensional stability of polymers present in MCU (i.e., PEEK, Grafoil, Tefzel and Isolast) in the modified NGS (where the concentration of LIX{reg_sign}79 and MaxCalix was varied systematically) showed that LIX{reg_sign}79 selectively affected Tefzel and its different grades (by an increase in size and lowering its density). The copolymer structure of Tefzel and possibly its porosity allows for the easier diffusion of LIX{reg_sign}79. Tefzel is used as the seat material in some of the valves at MCU. Long term exposure to LIX{reg_sign}79, may make the valves hard to operate over time due to the seat material (Tefzel) increasing in size. However, since the physical changes of Tefzel in the improved solvent are comparable to the changes in the CSSX baseline solvent, no design changes are needed with respect to the Tefzel seating material. PEEK, Grafoil and Isolast were not affected by LIX{reg_sign}79 and MaxCalix within six months of exposure. The initial rapid weight gain observed in every polymer is assigned to the finite and

  15. Demonstration of Caustic-Side Solvent Extraction with Savannah River Site High Level Waste

    International Nuclear Information System (INIS)

    Walker, D.D.

    2001-01-01

    Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet for the decontamination of high level waste using a 33-stage, 2-cm centrifugal contactor apparatus at the Savannah River Technology Center. This represents the first CSSX process demonstration using Savannah River Site (SRS) high level waste. Three tests lasting 6, 12, and 48 hours processed simulated average SRS waste, simulated Tank 37H/44F composite waste, and Tank 37H/44F high level waste, respectively

  16. Next Generation Solvent Development for Caustic-Side Solvent Extraction of Cesium

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, Bruce A. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Birdwell, Joseph F. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Bonnesen, Peter V. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)

    2014-03-01

    This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modular Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Inter laboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.

  17. Next Generation Solvent (NGS): Development for Caustic-Side Solvent Extraction of Cesium

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Birdwell, Jr, Joseph F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bonnesen, Peter V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Delmau, Laetitia Helene [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Duncan, Nathan C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ensor, Dale [Tennessee Technological Univ., Cookeville, TN (United States); Hill, Talon G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lee, Denise L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Rajbanshi, Arbin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Roach, Benjamin D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Szczygiel, Patricia L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sloop, Jr., Frederick V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stoner, Erica L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Williams, Neil J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-03-01

    This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modular Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Interlaboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.

  18. Follicular unit extraction as a therapeutic option for Vitiligo

    Directory of Open Access Journals (Sweden)

    S Sacchidanand

    2013-01-01

    Full Text Available Follicular unit extraction (FUE is a surgical procedure, which can be used to transplant follicular units into vitiliginous areas. Such follicular unit transplant has been recently used to repigment stable vitiligo patches. FUE was done for a 12-year-old female with a stable vitiligo patch with leukotrichia on the eyebrow. Repigmentation was noted in 6 weeks and complete pigmentation seen at 12 weeks. Leukotrichia resolved over a period of 6 months. No recurrence was noted at the end of 6 months follow-up with excellent colour match. This case is presented to highlight the simplicity, safety and effectiveness of FUE in stable vitiligo patches with leukotrichia.

  19. Direct hair transplantation: A modified follicular unit extraction technique

    Directory of Open Access Journals (Sweden)

    Pradeep Sethi

    2013-01-01

    Full Text Available Background: In hair transplantation, the survival rate of harvested grafts depends upon many factors like maintenance of hydration, cold temperature, reduced mechanical handling and asepsis. All these factors are favourably improved if time out of body is reduced significantly. We have tried a modification called direct hair transplantation in the existing follicular unit extraction technique, in which the follicular unit grafts are implanted as soon as they are harvested. In this article, we have described the detailed methodology and a series of 29 patients who underwent direct hair transplantation. Aim: To evaluate the efficacy and feasibility of direct hair transplantation. Subjects and Methods: The patients willing to undergo hair transplantation by the technique of follicular unit extraction were enrolled for the surgery. After administration of local anaesthesia, the recipient sites were created. Thereafter, the processes of scoring the skin with a motorized punch, graft extraction and implantation were performed simultaneously. These patients were followed up to look for the time period of initiation of hair growth, the growth achieved at the end of 6-8 months and any adverse events. The results of patients with noticeable improvement in the photographs and reduction in baldness grade were taken as ′good′, whereas, in other patients, it was classified as ′poor′. Results: All patients were males with age ranging from 21 to 66 years (median 30 years. Twenty-six patients had androgenetic alopecia, 1 patient had traction alopecia and 2 patients had scarring alopecia. Twenty-seven patients showed ′good′ results, whereas 2 patients showed ′poor′ results. Conclusion: Direct hair transplantation is a simple and feasible modification in the follicular unit extraction technique. It is an efficacious surgical treatment modality for baldness.

  20. Exploring support for shale gas extraction in the United Kingdom

    International Nuclear Information System (INIS)

    Andersson-Hudson, Jessica; Knight, William; Humphrey, Mathew; O’Hara, Sarah

    2016-01-01

    The development of shale gas in the United Kingdom (UK) using hydraulic fracturing, more commonly known as ‘fracking’, remains in its infancy. Yet understanding public attitudes for this fledgling industry is important for future policy considerations, decision-making and for industry stakeholders. This study uses data collected from the University of Nottingham, UK nationwide online survey (n=3823) conducted in September 2014, to consider ten hypothesises about the UK public's attitudes towards shale gas. From the survey data we can see that 43.11% of respondents support shale gas extraction in the UK. Furthermore, our results show that women, class DE respondents, non-Conservative party supporters, and respondents who positively associate shale gas with water contamination or earthquakes are less likely to support the extraction of shale gas in the UK. We also discuss potential policy implications for the UK government arising from these findings. - Highlights: • September 2014 survey of British attitudes towards allowing shale gas extraction. • Over 75% or respondents correctly identify shale gas. • 43.11% of respondents support shale gas extraction in the UK.

  1. Caustic-Side Solvent Extraction Chemical and Physical Properties Progress in FY 2000 and FY 2001.

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, BA

    2002-04-17

    The purpose of this work was to provide chemical- and physical-property data addressing the technical risks of the Caustic-Side Solvent Extraction (CSSX) process as applied specifically to the removal of cesium from alkaline high-level salt waste stored at the US Department of Energy Savannah River Site. As part of the overall Salt Processing Project, this effort supported decision-making in regards to selecting a preferred technology among three alternatives: (1) CSSX, (2) nonelutable ion-exchange with an inorganic silicotitanate material and (3) precipitation with tetraphenylborate. High risks, innate to CSSX, that needed specific attention included: (1) chemical stability of the solvent matrix, (2) radiolytic stability of the solvent matrix, (3) proof-of-concept performance of the proposed process flowsheet with simulated waste, and (4) performance of the CSSX flowsheet with actual SRS high-level waste. This body of work directly addressed the chemical-stability risk and additionally provided supporting information that served to plan, carry out, and evaluate experiments conducted by other CSSX investigators addressing the other high risks. Information on cesium distribution in extraction, scrubbing, and stripping served as input for flowsheet design, provided a baseline for evaluating solvent performance under numerous stresses, and contributed to a broad understanding of the effects of expected process variables. In parallel, other measurements were directed toward learning how other system components distribute in the flowsheet. Such components include the solvent components themselves, constituents of the waste, and solvent-degradation products. Upon understanding which components influence flowsheet performance, it was then possible to address in a rational fashion how to clean up the solvent and maintain its stable function.

  2. Partitioning of Tank Waste Sludge in a 5-cm Centrifugal Contactor Under Caustic-Side Solvent Extraction Conditions

    International Nuclear Information System (INIS)

    Birdwell, Jr. J.F.

    2001-01-01

    A test program has been performed to evaluate the effect of solids on the hydraulic performance of a 5-cm centrifugal contactor under conditions present in the extraction section of the Caustic-Side Solvent Extraction (CSSX) process. In addition to determining if the ability to separate the aqueous and organic phases is affected by the presence of solids in a feed solution, the extent to which solids are accumulated in the contactor was also assessed. The reported task was motivated by the need to determine if removal of cesium from Savannah River Site tank waste can be performed using a contactor-based CSSX process without first removing sludge that is suspended in the feed solution. The ability to pass solids through the CSSX process could facilitate placement of CSSX upstream of a process in which alpha-decaying actinides and strontium are removed from the waste stream by precipitation with monosodium titanate (MST). This relative placement of the CSSX and MST processes is desirable because removal of cesium would greatly reduce the activity level of the feed stream to the MST process, thereby reducing the level of shielding needed and mitigating remote maintenance design features of MST equipment. Both results would significantly reduce the cost of the Salt Processing Project. Test results indicate conclusively that a large fraction of suspended sludge that enters the centrifugal contactor remains inside. It is expected that extended operation would result in continued accumulation of solids and that hydraulic performance would be adversely affected. Results also indicate that a fraction of the solids partitions to the phase boundary and could affect phase separation as contactor operations progress

  3. Eyelash Transplantation Using Leg Hair by Follicular Unit Extraction

    Directory of Open Access Journals (Sweden)

    Sanusi Umar, MD

    2015-03-01

    Full Text Available Summary: Fine hairs of the head and nape areas have been used as donor sources in eyelash transplantation but are straight, coarse, and grow rapidly, requiring frequent eyelash maintenance. This is the first reported case of eyelash transplantation by follicular unit extraction using leg hair as a donor source; findings were compared with that of another patient who underwent a similar procedure with donor hairs from the nape area. Although both patients reported marked improvement in fullness of eyelashes within 3 months postsurgery, the transplanted leg hair eyelashes required less frequent trimming (every 5–6 weeks compared with nape hair eyelashes (every 2–3 weeks. Additionally, in leg hair eyelashes, the need for perming to sustain a natural looking eyelash curl was eliminated. Eyelash transplantation using leg donor hair in hirsute women may result in good cosmetic outcomes and require less maintenance compared with nape donor hair.

  4. Follicular Unit Extraction Hair Transplantation with Micromotor: Eight Years Experience.

    Science.gov (United States)

    Ors, Safvet; Ozkose, Mehmet; Ors, Sevgi

    2015-08-01

    Follicular unit extraction (FUE) has been performed for over a decade. Our experience in the patients who underwent hair transplantation using only the FUE method was included in this study. A total of 1000 patients had hair transplantation using the FUE method between 2005 and 2014 in our clinic. Manual punch was used in 32 and micromotor was used in 968 patients for graft harvesting. During the time that manual punch was used for graft harvesting, 1000-2000 grafts were transplanted in one session in 6-8 h. Following micromotor use, the average graft count was increased to 2500 and the operation time remained unchanged. Graft take was difficult in 11.1 %, easy in 52.2 %, and very easy in 36.7 % of our patients. The main purpose of hair transplantation is to restore the hair loss. During the process, obtaining a natural appearance and adequate hair intensity is important. In the FUE method, grafts can be taken without changing their natural structure, there is no need for magnification, and the grafts can be transplanted directly without using any other processes. Because there is no suture in the FUE method, patients do not experience these incision site problems and scar formation. The FUE method enables us to achieve a natural appearance with less morbidity.

  5. Combined Extraction of Cesium, Strontium, and Actinides from Alkaline Media: An Extension of the Caustic-Side Solvent Extraction (CSSX) Process Technology

    International Nuclear Information System (INIS)

    Kenneth Raymond

    2004-01-01

    The wastes present at DOE long-term storage sites are usually highly alkaline, and because of this, much of the actinides in these wastes are in the sludge phase. Enough actinide materials still remain in the supernatant liquid that they require separation followed by long-term storage in a geological repository. The removal of these metals from the liquid waste stream would permit their disposal as low-level waste and dramatically reduce the volume of high-level wastes

  6. Caustic-Side Solvent-Extraction Modeling for Hanford Interim Pretreatment System

    International Nuclear Information System (INIS)

    Moyer, B.A.; Birdwell, J.F.; Delmau, L. H.; McFarlane, J.

    2008-01-01

    The purpose of this work is to examine the applicability of the Caustic-Side Solvent Extraction (CSSX) process for the removal of cesium from Hanford tank-waste supernatant solutions in support of the Hanford Interim Pretreatment System (IPS). The Hanford waste types are more challenging than those at the Savannah River Site (SRS) in that they contain significantly higher levels of potassium, the chief competing ion in the extraction of cesium. It was confirmed by use of the CSSX model that the higher levels of potassium depress the cesium distribution ratio (DCs), as validated by measurement of DCs values for four of eight specified Hanford waste-simulant compositions. The model predictions were good to an apparent standard error of ±11%. It is concluded from batch distribution experiments, physical-property measurements, equilibrium modeling, flowsheet calculations, and contactor sizing that the CSSX process as currently employed for cesium removal from alkaline salt waste at the SRS is capable of treating similar Hanford tank feeds. For the most challenging waste composition, 41 stages would be required to provide a cesium decontamination factor (DF) of 5000 and a concentration factor (CF) of 5. Commercial contacting equipment with rotor diameters of 10 in. for extraction and 5 in. for stripping should have the capacity to meet throughput requirements, but testing will be required to confirm that the needed efficiency and hydraulic performance are actually obtainable. Markedly improved flowsheet performance was calculated for a new solvent formulation employing the more soluble cesium extractant BEHBCalixC6 used with alternative scrub and strip solutions, respectively 0.1 M NaOH and 10 mM boric acid. The improved system can meet minimum requirements (DF = 5000 and CF = 5) with 17 stages or more ambitious goals (DF = 40,000 and CF = 15) with 19 stages. Potential benefits of further research and development are identified that would lead to reduced costs, greater

  7. Application of ion-exchange unit in uranium extraction process in China (to be continued)

    International Nuclear Information System (INIS)

    Gong Chuanwen

    2004-01-01

    The application conditions of five different ion exchange units in uranium milling plant and wastewater treatment plant of uranium mine in China are introduced, including working parameters, existing problems and improvements. The advantages and disadvantages of these units are reviewed briefly. The procedure points to be followed in selecting ion exchange unit are recommended in the engineering design. The primary views are presented upon the application prospects of some ion exchange units in uranium extraction process in China

  8. Results of testing the frontal AK-3 extraction unit

    Energy Technology Data Exchange (ETDEWEB)

    Yakovlev, N I; Dolinskii, A M; Kolesnikov, M A

    1978-10-01

    From August to November 1970, on site testing of a protype frontal AK excavating rig developed by Giprouglemesh for use on gentle sloping seams was conducted in the Novaya mine of the Kuzbass Ugol Consolidated. The AK-3 consists of a cutting assembly in the form of a ring frontal slicer with two drives, hydraulic operated sectionalized support timbers of the enclosed lift type, conjugated timbering with ventilation and conveyor shafts, personnel elevator and hydraulic and electrical ancillary equipment. The production capacity of the rig in longwalls is 2.2 times greater on the average than by using drillhole blasting methods. Tests demonstrated that the main advantage of the Ak-3 was the single operation, continuous flow mode of coal extraction and remote frontal movement of timber sections, which ensured high capacity loading at the face and the capability of automating all procedures and eliminating all workers from the extraction face.

  9. Specification of an Expert system for the control of extraction units in reprocessing plants

    International Nuclear Information System (INIS)

    Jorda, A.; Charon, E.; Coppens, P.; Romet, J.L.

    1986-01-01

    Industrial operation of extraction units in reprocessing plants is very complex because the great number of chemical and hydraulic parameters to take into account. This complexity associated to the impossibility to see inside the active enclosures make difficult the operation processes, diagnosis and corrections. Management of parameters by an expert system will increase productivity and safety of solvent extraction in pulsed columns [fr

  10. Exploring support for shale gas extraction in the United Kingdom

    OpenAIRE

    Andersson-Hudson, Jessica; Knight, Wil; Humphrey, Mathew; O'Hara, Sarah

    2016-01-01

    The development of shale gas in the United Kingdom (UK) using hydraulic fracturing, more commonly known as ‘fracking’, remains in its infancy. Yet understanding public attitudes for this fledgling industry is important for future policy considerations, decision-making and for industry stakeholders. This study uses data collected from the University of Nottingham UK nationwide online survey (n=3,823) conducted in September 2014, to consider ten hypothesises about the UK public’s attitudes towa...

  11. The science and art of eyebrow transplantation by follicular unit extraction

    Directory of Open Access Journals (Sweden)

    Jyoti Gupta

    2017-01-01

    Full Text Available Eyebrows constitute a very important and prominent feature of the face. With growing information, eyebrow transplant has become a popular procedure. However, though it is a small area it requires a lot of precision and knowledge regarding anatomy, designing of brows, extraction and implantation technique. This article gives a comprehensive view regarding eyebrow transplant with special emphasis on follicular unit extraction technique, which has become the most popular technique.

  12. The Science and Art of Eyebrow Transplantation by Follicular Unit Extraction

    Science.gov (United States)

    Gupta, Jyoti; Kumar, Amrendra; Chouhan, Kavish; Ariganesh, C; Nandal, Vinay

    2017-01-01

    Eyebrows constitute a very important and prominent feature of the face. With growing information, eyebrow transplant has become a popular procedure. However, though it is a small area it requires a lot of precision and knowledge regarding anatomy, designing of brows, extraction and implantation technique. This article gives a comprehensive view regarding eyebrow transplant with special emphasis on follicular unit extraction technique, which has become the most popular technique. PMID:28852290

  13. Development and validation of an automated unit for the extraction of radiocaesium from seawater

    International Nuclear Information System (INIS)

    Bokor, Ilonka; Sdraulig, Sandra; Jenkinson, Peter; Madamperuma, Janaka; Martin, Paul

    2016-01-01

    An automated unit was developed for the in-situ extraction of radiocaesium ( 137 Cs and 134 Cs) from large volumes of seawater to achieve very low detection limits. The unit was designed for monitoring of Australian ocean and coastal waters, including at ports visited by nuclear-powered warships. The unit is housed within a robust case, and is easily transported and operated. It contains four filter cartridges connected in series. The first two cartridges are used to remove any suspended material that may be present in the seawater, while the last two cartridges are coated with potassium copper hexacyanoferrate for caesium extraction. Once the extraction is completed the coated cartridges are ashed. The ash is transferred to a small petri dish for counting of 137 Cs and 134 Cs by high resolution gamma spectrometry for a minimum of 24 h. The extraction method was validated for the following criteria: selectivity, trueness, precision, linearity, limit of detection and traceability. The validation showed the unit to be fit for purpose with the method capable of achieving low detection limits required for environmental samples. The results for the environmental measurements in Australian seawater correlate well with those reported in the Worldwide Marine Radioactivity Study (WOMARS). The cost of preparation and running the system is low and waste generation is minimal. - Highlights: • Automated unit for in-situ extraction of 137 Cs and 134 Cs from 1000 L of seawater. • Unit is robust, and easily transported and operated. • Cs extraction uses cartridges coated with potassium copper hexacyanoferrate. • Validated for selectivity, trueness, precision, linearity, LOD and traceability. • System fit for purpose for monitoring of Australian coastal and ocean waters.

  14. Updated United Nations Framework Classification for reserves and resources of extractive industries

    Science.gov (United States)

    Ahlbrandt, T.S.; Blaise, J.R.; Blystad, P.; Kelter, D.; Gabrielyants, G.; Heiberg, S.; Martinez, A.; Ross, J.G.; Slavov, S.; Subelj, A.; Young, E.D.

    2004-01-01

    The United Nations have studied how the oil and gas resource classification developed jointly by the SPE, the World Petroleum Congress (WPC) and the American Association of Petroleum Geologists (AAPG) could be harmonized with the United Nations Framework Classification (UNFC) for Solid Fuel and Mineral Resources (1). The United Nations has continued to build on this and other works, with support from many relevant international organizations, with the objective of updating the UNFC to apply to the extractive industries. The result is the United Nations Framework Classification for Energy and Mineral Resources (2) that this paper will present. Reserves and resources are categorized with respect to three sets of criteria: ??? Economic and commercial viability ??? Field project status and feasibility ??? The level of geologic knowledge The field project status criteria are readily recognized as the ones highlighted in the SPE/WPC/AAPG classification system of 2000. The geologic criteria absorb the rich traditions that form the primary basis for the Russian classification system, and the ones used to delimit, in part, proved reserves. Economic and commercial criteria facilitate the use of the classification in general, and reflect the commercial considerations used to delimit proved reserves in particular. The classification system will help to develop a common understanding of reserves and resources for all the extractive industries and will assist: ??? International and national resources management to secure supplies; ??? Industries' management of business processes to achieve efficiency in exploration and production; and ??? An appropriate basis for documenting the value of reserves and resources in financial statements.

  15. Effect of concentration of the height of a transfer unit in a liquid/liquid solvent-extraction system

    International Nuclear Information System (INIS)

    Chamberlain, D.B.

    1981-05-01

    Pulsed, sieve-plate extraction columns were used to examine the effect of solute concentration on extraction efficiency. Cerium was extracted from an aqueous coprocessing solution, simulating reprocessing wastes produced at the Idaho Chemical Processing Plant. The organic extractant used in this process was dihexyl-N, N-diethylcarbamylmethylene phosphonate. Subsequently, cerium was stripped from the organic phase with 0.05 M nitric acid. The Heights of a Transfer Unit were calculated from the extraction and stripping column operating data. Both interstage and overall transfer units were calculated. Nine extraction and nine stripping tests were performed. Three extraction feed concentrations, each repeated at three different pulse frequencies were used to study the affect of concentration on height of a transfer unit. The stripping column was operated simultaneously with the extraction column. Both columns were operated at pulse amplitudes of 2.5 cm. Data based upon the overall extraction column showed a slight decrease in the height of a transfer unit as the solute concentration decreased. Based upon the overall stripping column data, a decrease in solute concentration resulted in a very slight increase in the height of a transfer unit. However, interstage transfer unit calculations for both columns indicated solute concentration had no significant effect on the height of a transfer unit. Based on the experimental tests, it was concluded that solute concentration caused only slight changes in extraction efficiency for the concentration range studied. Other factors such as pulse frequency, aqueous/organic flow ratio, and possibly the dispersed phase bubble size had a much greater effect on the extraction efficiency for the system studied

  16. Extraction, Scrub, and Strip Test Results for the Salt Waste Processing Facility Caustic Side Solvent Extraction Solvent Sample

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-10-06

    An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 12.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges. This revision was created to correct an error. The previous revision used an incorrect set of temperature correction coefficients which resulted in slight deviations from the correct D(Cs) results.

  17. Extraction, scrub, and strip test results for the salt waste processing facility caustic side solvent extraction solvent example

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-08-01

    An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 12.9, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.

  18. SpecOp: Optimal Extraction Software for Integral Field Unit Spectrographs

    Science.gov (United States)

    McCarron, Adam; Ciardullo, Robin; Eracleous, Michael

    2018-01-01

    The Hobby-Eberly Telescope’s new low resolution integral field spectrographs, LRS2-B and LRS2-R, each cover a 12”x6” area on the sky with 280 fibers and generate spectra with resolutions between R=1100 and R=1900. To extract 1-D spectra from the instrument’s 3D data cubes, a program is needed that is flexible enough to work for a wide variety of targets, including continuum point sources, emission line sources, and compact sources embedded in complex backgrounds. We therefore introduce SpecOp, a user-friendly python program for optimally extracting spectra from integral-field unit spectrographs. As input, SpecOp takes a sky-subtracted data cube consisting of images at each wavelength increment set by the instrument’s spectral resolution, and an error file for each count measurement. All of these files are generated by the current LRS2 reduction pipeline. The program then collapses the cube in the image plane using the optimal extraction algorithm detailed by Keith Horne (1986). The various user-selected options include the fraction of the total signal enclosed in a contour-defined region, the wavelength range to analyze, and the precision of the spatial profile calculation. SpecOp can output the weighted counts and errors at each wavelength in various table formats using python’s astropy package. We outline the algorithm used for extraction and explain how the software can be used to easily obtain high-quality 1-D spectra. We demonstrate the utility of the program by applying it to spectra of a variety of quasars and AGNs. In some of these targets, we extract the spectrum of a nuclear point source that is superposed on a spatially extended galaxy.

  19. THERMAL AND SPECTROSCOPIC ANALYSES OF CAUSTIC SIDE SOLVENT EXTRACTION SOLVENT CONTACTED WITH 16 MOLAR AND 8 MOLAR NITRIC ACID

    International Nuclear Information System (INIS)

    Fondeur, F; David Hobbs, D; Samuel Fink, S

    2007-01-01

    Thermal and spectroscopic analyses were performed on multiple layers formed from contacting Caustic Side Solvent Extraction (CSSX) solvent with 1 M or 3 M nitric acid. A slow chemical reaction occurs (i.e., over several weeks) between the solvent and 1 M or 3 M nitric acid as evidenced by color changes and the detection of nitro groups in the infrared spectrum of the aged samples. Thermal analysis revealed that decomposition of the resulting mixture does not meet the definition of explosive or deflagrating material

  20. Combining Follicular Unit Extraction and Scalp Micropigmentation for the Cosmetic Treatment of Alopecias

    Directory of Open Access Journals (Sweden)

    William Rassman, MD

    2017-11-01

    Full Text Available Two relatively new modalities, follicular unit extraction (FUE and scalp micropigmentation have changed the treatment of hair loss, to reduce the number of procedures and the total costs of the hair restoration process. These 2 modalities augment each other when treating patients with thinning hair and balding. The explosion of FUE procedures (which reflected 52.6% of the hair transplant procedures performed in 2016, up from 48.5% and the appearance of more and more new physicians offering hair restoration technologies employing FUE have caused a 20% annual growth in this industry over the past few years. This article reviews the use of FUE and scalp micropigmentation when used in combination.

  1. EXTRACT

    DEFF Research Database (Denmark)

    Pafilis, Evangelos; Buttigieg, Pier Luigi; Ferrell, Barbra

    2016-01-01

    The microbial and molecular ecology research communities have made substantial progress on developing standards for annotating samples with environment metadata. However, sample manual annotation is a highly labor intensive process and requires familiarity with the terminologies used. We have the...... and text-mining-assisted curation revealed that EXTRACT speeds up annotation by 15-25% and helps curators to detect terms that would otherwise have been missed.Database URL: https://extract.hcmr.gr/......., organism, tissue and disease terms. The evaluators in the BioCreative V Interactive Annotation Task found the system to be intuitive, useful, well documented and sufficiently accurate to be helpful in spotting relevant text passages and extracting organism and environment terms. Comparison of fully manual...

  2. Extraction, scrub, and strip test results for the solvent transfer to salt waste processing facility

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-09-07

    The Savannah River National Laboratory (SRNL) prepared approximately 240 gallons of Caustic-Side Solvent Extraction (CSSX) solvent for use at the Salt Waste Processing Facility (SWPF). An Extraction, Scrub, and Strip (ESS) test was performed on a sample of the prepared solvent using a salt solution prepared by Parsons to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams. This data will be used by Parsons to help qualify the solvent for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(Cs) measured 15.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.

  3. Solvent Extraction Batch Distribution Coefficients with Savannah River Site Dissolved Salt Cake

    International Nuclear Information System (INIS)

    Walker, D.D.

    2002-01-01

    Researchers characterized high-level waste derived from dissolved salt cake from the Savannah River Site (SRS) tank farm and measured the cesium distribution coefficients (DCs) for extraction, scrub, and stripping steps of the caustic-side solvent extraction (CSSX) flowsheet. The measurements used two SRS high-level waste samples derived entirely or in part from salt cake. The chemical compositions of both samples are reported. Dissolved salt cake waste contained less Cs-137 and more dianions than is typical of supernate samples. Extraction and scrub DCs values for both samples exceeded process requirements and agreed well with model predictions. Strip DCs values for the Tank 46F sample also met process requirements. However, strip DCs values could not be calculated for the Tank 38H sample due to the poor material balance for Cs-137. Potential explanations for the poor material balance are discussed and additional work to determine the cause is described

  4. Design Analysis of Power Extracting Unit of an Onshore OWC Based Wave Energy Power Plant using Numerical Simulation

    Directory of Open Access Journals (Sweden)

    Zahid Suleman

    2011-07-01

    Full Text Available This research paper describes design and analysis of power extracting unit of an onshore OWC (Oscillating Water Column based wave energy power plant of capacity about 100 kilowatts. The OWC is modeled as solid piston of a reciprocating pump. The power extracting unit is designed analytically by using the theory of reciprocating pumps and principles of fluid mechanics. Pro-E and ANSYS workbench softwares are used to verify the analytical design. The analytical results of the flow velocity in the turbine duct are compared with the simulation results. The results are found to be in good agreement with each other. The results achieved by this research would finally assist in the overall design of the power plant which is the ultimate goal of this research work.

  5. The Effect of One Session Low Level Laser Therapy of Extracted Follicular Units on the Outcome of Hair Transplantation

    OpenAIRE

    Tabaie, Seyed Mehdi; Berenji Ardestani, Hoda; Azizjalali, Mir Hadi

    2016-01-01

    Introduction: Photobiostimulation with low level laser (LLL) has been used in medicine for a long time and its effects have been shown in many diseases. Some studies have evaluated the effect of LLL on androgenic alopecia. One of the most important limitations of the use of LLL in the treatment of alopecia is the requirement for multiple sessions, which is hardly accepted by patients. This study was conducted to evaluate the effect of the irradiation of extracted follicular hair units by LLL ...

  6. Caustic-Side Solvent Extraction: Chemical and Physical Properties of the Optimized Solvent

    Energy Technology Data Exchange (ETDEWEB)

    Delmau, L.H.

    2002-10-08

    This work was undertaken to optimize the solvent used in the Caustic Side Solvent Extraction (CSSX) process and to measure key chemical and physical properties related to its performance in the removal of cesium from the alkaline high-level salt waste stored in tanks at the Savannah River Site. The need to adjust the solvent composition arose from the prior discovery that the previous baseline solvent was supersaturated with respect to the calixarene extractant. The following solvent-component concentrations in Isopar{reg_sign} L diluent are recommended: 0.007 M calix[4]arene-bis(tert-octylbenzo-crown-6) (BOBCalixC6) extractant, 0.75 M 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol (Cs-7SB) phase modifier, and 0.003 M tri-n-octylamine (TOA) stripping aid. Criteria for this selection included BOBCalixC6 solubility, batch cesium distribution ratios (D{sub Cs}), calculated flowsheet robustness, third-phase formation, coalescence rate (dispersion numbers), and solvent density. Although minor compromises within acceptable limits were made in flowsheet robustness and solvent density, significant benefits were gained in lower risk of third-phase formation and lower solvent cost. Data are also reported for the optimized solvent regarding the temperature dependence of D{sub Cs} in extraction, scrubbing, and stripping (ESS); ESS performance on recycle; partitioning of BOBCalixC6, Cs-7SB, and TOA to aqueous process solutions; partitioning of organic anions; distribution of metals; solvent phase separation at low temperatures; solvent stability to elevated temperatures; and solvent density and viscosity. Overall, the technical risk of the CSSX process has been reduced by resolving previously identified issues and raising no new issues.

  7. Caustic-Side Solvent Extraction: Prediction of Cesium Extraction from Actual Wastes and Actual Waste Simulants

    International Nuclear Information System (INIS)

    Delmau, L.H.; Haverlock, T.J.; Sloop, F.V. Jr.; Moyer, B.A.

    2003-01-01

    This report presents the work that followed the CSSX model development completed in FY2002. The developed cesium and potassium extraction model was based on extraction data obtained from simple aqueous media. It was tested to ensure the validity of the prediction for the cesium extraction from actual waste. Compositions of the actual tank waste were obtained from the Savannah River Site personnel and were used to prepare defined simulants and to predict cesium distribution ratios using the model. It was therefore possible to compare the cesium distribution ratios obtained from the actual waste, the simulant, and the predicted values. It was determined that the predicted values agree with the measured values for the simulants. Predicted values also agreed, with three exceptions, with measured values for the tank wastes. Discrepancies were attributed in part to the uncertainty in the cation/anion balance in the actual waste composition, but likely more so to the uncertainty in the potassium concentration in the waste, given the demonstrated large competing effect of this metal on cesium extraction. It was demonstrated that the upper limit for the potassium concentration in the feed ought to not exceed 0.05 M in order to maintain suitable cesium distribution ratios

  8. The Effect of One Session Low Level Laser Therapy of Extracted Follicular Units on the Outcome of Hair Transplantation.

    Science.gov (United States)

    Tabaie, Seyed Mehdi; Berenji Ardestani, Hoda; Azizjalali, Mir Hadi

    2016-01-01

    Photobiostimulation with low level laser (LLL) has been used in medicine for a long time and its effects have been shown in many diseases. Some studies have evaluated the effect of LLL on androgenic alopecia. One of the most important limitations of the use of LLL in the treatment of alopecia is the requirement for multiple sessions, which is hardly accepted by patients. This study was conducted to evaluate the effect of the irradiation of extracted follicular hair units by LLL on the outcome of hair transplantation. We enrolled 10 patients with androgenic alopecia and after screening tests for infections and other diseases, we extracted hair follicular units. The hair units were divided in two groups. One group was irradiated by LLL 20 minutes before transplantation (660 nm, 80 Hz, 100 mW) and the other one was used as control. The containing plates were labeled as A and B and sent to the operation room. The surgeon was unaware of the therapy assigned to the plates and transplanted them randomly on the right or left side of the head. One hundred follicular units on each sides of the scalp were transplanted symmetrically. The follicles on both sides were evaluated at 3 and 6 months of transplantation for hair growth rate by another physician, blinded to the treatment assigned to each side. Ten patient with androgenic alopecia and mean (SD) age of 31.5 (6.6) years (range 25-45 years) completed the study. All patients had 100% hair growth at 3 and 6 months follow-up except one who had hair growth of 20% at three months of transplantation, which changed to 100% at sixth months. There was no significant difference between the groups regarding hair growth (P > 0.8). One session of LLL irradiation has no significant effect on the outcome of transplanted hair follicles. Studies with larger sample size are needed to draw a definite conclusion.

  9. The effect of recording site on extracted features of motor unit action potential.

    Science.gov (United States)

    Artuğ, N Tuğrul; Goker, Imran; Bolat, Bülent; Osman, Onur; Kocasoy Orhan, Elif; Baslo, M Baris

    2016-06-01

    Motor unit action potential (MUAP), which consists of individual muscle fiber action potentials (MFAPs), represents the electrical activity of the motor unit. The values of the MUAP features are changed by denervation and reinnervation in neurogenic involvement as well as muscle fiber loss with increased diameter variability in myopathic diseases. The present study is designed to investigate how increased muscle fiber diameter variability affects MUAP parameters in simulated motor units. In order to detect this variation, simulated MUAPs were calculated both at the innervation zone where the MFAPs are more synchronized, and near the tendon, where they show increased temporal dispersion. Reinnervation in neurogenic state increases MUAP amplitude for the recordings at both the innervation zone and near the tendon. However, MUAP duration and the number of peaks significantly increased in a case of myopathy for recordings near the tendon. Furthermore, of the new features, "number of peaks×spike duration" was found as the strongest indicator of MFAP dispersion in myopathy. MUAPs were also recorded from healthy participants in order to investigate the biological counterpart of the simulation data. MUAPs which were recorded near to tendon revealed significantly prolonged duration and decreased amplitude. Although the number of peaks was increased by moving the needle near to tendon, this was not significant. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  10. Efficient Statistical Extraction of the Per-Unit-Length Capacitance and Inductance Matrices of Cables with Random Parameters

    Directory of Open Access Journals (Sweden)

    P. Manfredi

    2015-05-01

    Full Text Available Cable bundles often exhibit random parameter variations due to uncertain or uncontrollable physical properties and wire positioning. Efficient tools, based on the so-called polynomial chaos, exist to rapidly assess the impact of such variations on the per-unit-length capacitance and inductance matrices, and on the pertinent cable response. Nevertheless, the state-of-the-art method for the statistical extraction of the per-unit-length capacitance and inductance matrices of cables suffers from several inefficiencies that hinder its applicability to large problems, in terms of number of random parameters and/or conductors. This paper presents an improved methodology that overcomes the aforementioned limitations by exploiting a recently-published, alternative approach to generate the pertinent polynomial chaos system of equations. A sparse and decoupled system is obtained that provides remarkable benefits in terms of speed, memory consumption and problem size that can be dealt with. The technique is thoroughly validated through the statistical analysis of two canonical structures, i.e. a ribbon cable and a shielded cable with random geometry and position.

  11. UNEP (United Nations Environment Program) discussed the environmental impacts of extraction, transportation, and utilization of fossil fuels

    Energy Technology Data Exchange (ETDEWEB)

    1978-07-01

    The UNEP (United Nations Environment Program) discussed the environmental impacts of extraction, transportation, and utilization of fossil fuels at a meeting in Warsaw, the first in a series of UNEP undertakings, to be followed by studies on nuclear energy and renewable energy sources. The major issues examined at the meeting were human health effects of atmospheric emissions, especially SO/sub 2/; effects of SO/sub 2/ on vegetation and bodies of fresh water; long-term ecologic effects of oil spills in the sea; and potential effects on climate from atmospheric CO/sub 2/ arising from fossil fuel combustion. A doubling of the atmospheric CO/sub 2/ concentration would cause an estimated 1.5/sup 0/-3.0/sup 0/C increase in the surface air temperature. With an amount of CO/sub 2/ equivalent to 0.5 x 10/sup 10/ tonnes of carbon annually injected into the atmosphere from fossil fuels, of which only 0.27 x 10/sup 10/ tonnes are removed by some exchange processes with ocean or land. A 17% increase in atmospheric CO/sub 2/ over the 1976 concentration of 332 ppm is expected by the year 2000.

  12. Results Of The Extraction-Scrub-Strip Testing Using An Improved Solvent Formulation And Salt Waste Processing Facility Simulated Waste

    International Nuclear Information System (INIS)

    Peters, T.; Washington, A.; Fink, S.

    2012-01-01

    The Office of Waste Processing, within the Office of Technology Innovation and Development, is funding the development of an enhanced solvent - also known as the next generation solvent (NGS) - for deployment at the Savannah River Site to remove cesium from High Level Waste. The technical effort is a collaborative effort between Oak Ridge National Laboratory (ORNL) and Savannah River National Laboratory (SRNL). As part of the program, the Savannah River National Laboratory (SRNL) has performed a number of Extraction-Scrub-Strip (ESS) tests. These batch contact tests serve as first indicators of the cesium mass transfer solvent performance with actual or simulated waste. The test detailed in this report used simulated Tank 49H material, with the addition of extra potassium. The potassium was added at 1677 mg/L, the maximum projected (i.e., a worst case feed scenario) value for the Salt Waste Processing Facility (SWPF). The results of the test gave favorable results given that the potassium concentration was elevated (1677 mg/L compared to the current 513 mg/L). The cesium distribution value, DCs, for extraction was 57.1. As a comparison, a typical D Cs in an ESS test, using the baseline solvent formulation and the typical waste feed, is ∼15. The Modular Caustic Side Solvent Extraction Unit (MCU) uses the Caustic-Side Solvent Extraction (CSSX) process to remove cesium (Cs) from alkaline waste. This process involves the use of an organic extractant, BoBCalixC6, in an organic matrix to selectively remove cesium from the caustic waste. The organic solvent mixture flows counter-current to the caustic aqueous waste stream within centrifugal contactors. After extracting the cesium, the loaded solvent is stripped of cesium by contact with dilute nitric acid and the cesium concentrate is transferred to the Defense Waste Processing Facility (DWPF), while the organic solvent is cleaned and recycled for further use. The Salt Waste Processing Facility (SWPF), under

  13. Caustic-Side Solvent Extraction: Anti-Caking Surfactants Found to be Cause of Apparent Effect of High Nitrite Concentration on Cesium Stripping

    Energy Technology Data Exchange (ETDEWEB)

    Delmau, L.H.

    2002-06-13

    Experiments conducted in FY01 previously indicated a potential cesium stripping problem in the CSSX process due to the presence of nitrite in the waste simulant. The stripping issue seemed all the more important as the nitrite concentration increased. Experiments presented in this work have demonstrated that the true reason for the cesium stripping problem was in fact the presence of an anti-caking agent in the,sodium nitrite. used for the preparation of the simulants. The anti-caking agent is actually a mixture of well-known surfactants, sodium mono- and di-methyl naphthalene sulfonate that can partition into the organic-phase on extraction, then retain cesium upon stripping. The effect was demonstrated by adding known amounts of the anti-caking agent to clean systems. Data suggest that rejuvenation of the solvent can be obtained by a caustic wash following the stripping stage.

  14. State space model extraction of thermohydraulic systems – Part II: A linear graph approach applied to a Brayton cycle-based power conversion unit

    International Nuclear Information System (INIS)

    Uren, Kenneth Richard; Schoor, George van

    2013-01-01

    This second paper in a two part series presents the application of a developed state space model extraction methodology applied to a Brayton cycle-based PCU (power conversion unit) of a PBMR (pebble bed modular reactor). The goal is to investigate if the state space extraction methodology can cope with larger and more complex thermohydraulic systems. In Part I the state space model extraction methodology for the purpose of control was described in detail and a state space representation was extracted for a U-tube system to illustrate the concept. In this paper a 25th order nonlinear state space representation in terms of the different energy domains is extracted. This state space representation is solved and the responses of a number of important states are compared with results obtained from a PBMR PCU Flownex ® model. Flownex ® is a validated thermo fluid simulation software package. The results show that the state space model closely resembles the dynamics of the PBMR PCU. This kind of model may be used for nonlinear MIMO (multi-input, multi-output) type of control strategies. However, there is still a need for linear state space models since many control system design and analysis techniques require a linear state space model. This issue is also addressed in this paper by showing how a linear state space model can be derived from the extracted nonlinear state space model. The linearised state space model is also validated by comparing the state space model to an existing linear Simulink ® model of the PBMR PCU system. - Highlights: • State space model extraction of a pebble bed modular reactor PCU (power conversion unit). • A 25th order nonlinear time varying state space model is obtained. • Linearisation of a nonlinear state space model for use in power output control. • Non-minimum phase characteristic that is challenging in terms of control. • Models derived are useful for MIMO control strategies

  15. Placement of replace select Ti-Unite-coated type implants using a combination of immediate and submerge techniques after tooth extraction

    Directory of Open Access Journals (Sweden)

    Coen Pramono D

    2006-06-01

    Full Text Available The high success rate of immediate implant placement both in the anterior and posterior regions were reported by many authors, therefore applying this techniques can be considered as a safe surgical procedure and minimizing the dental office visit for patient satisfaction. This paper reports the outcome of immediate placement of implants following extraction of anterior maxillary teeth. Combination technique of immediate and submerge implant placements including bone grafting procedure were used. Four implants with TiUnite surface type were placed immediately in two patients with the short-term result indicated that this technique may serve as a simple and safe procedure for immediate implant placement. It was concluded that immediate implant placement technique combined with TiUnite implant surface was successful in treating region directly after tooth extraction therefore this technique can be use as an alternative surgical method for dental implant rehabilitation.

  16. Follicular unit extraction hair transplant automation: options in overcoming challenges of the latest technology in hair restoration with the goal of avoiding the line scar.

    Science.gov (United States)

    Rashid, Rashid M; Morgan Bicknell, Lindsay T

    2012-09-15

    Follicular unit extraction (FUE) provides many advantages over the strip surgical method of harvesting hair grafts for hair restoration. However, FUE also has its shortcomings because it is a more time intensive approach that results in increased costs and is technically a more challenging technique of hair transplantation. In this manuscript, we seek to share approaches used at our center to help minimize and/or improve on some of the challenges of FUE.

  17. Integrated sampling and analysis unit for the determination of sexual pheromones in environmental air using fabric phase sorptive extraction and headspace-gas chromatography-mass spectrometry.

    Science.gov (United States)

    Alcudia-León, M Carmen; Lucena, Rafael; Cárdenas, Soledad; Valcárcel, Miguel; Kabir, Abuzar; Furton, Kenneth G

    2017-03-10

    This article presents a novel unit that integrates for the first time air sampling and preconcentration based on the use of fabric phase sorptive extraction principles. The determination of Tuta absoluta sexual pheromone traces in environmental air has been selected as analytical problem. For this aim, a novel laboratory-built unit made up of commercial brass elements as holder of the sol-gel coated fabric extracting phase has been designed and optimized. The performance of the integrated unit was evaluated analyzing environmental air sampled in tomato crops. The unit can work under sampling and analysis mode which eliminates any need for sorptive phase manipulation prior to instrumental analysis. In the sampling mode, the unit can be connected to a sampling pump to pass the air through the sorptive phase at a controlled flow-rate. In the analysis mode, it is placed in the gas chromatograph autosampler without any instrumental modification. It also diminishes the risk of cross contamination between sampling and analysis. The performance of the new unit has been evaluated using the main components of the sexual pheromone of Tuta absoluta [(3E,8Z,11Z)-tetradecatrien-1-yl acetate and (3E,8Z)-tetradecadien-1-yl acetate] as model analytes. The limits of detection for both compounds resulted to be 1.6μg and 0.8μg, respectively, while the precision (expressed as relative standard deviation) was better than 3.7%. Finally, the unit has been deployed in the field to analyze a number of real life samples, some of them were found positive. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Characterization of Solids Deposited on the Modular Caustic-Side Solvent Extraction Unit (MCU) Strip Effluent (SE) Coalescer Media Removed in April 2015

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-06-13

    On June 2015, Savannah River National Laboratory (SRNL) received a Strip Effluent (SE) coalescer (FLT-304) from MCU. That coalescer was first installed at MCU in late October 2014 and removed in April 2015. While processing approximately 48,700 gallons of strip solution, the pressure drop steadily increased linearly from 1 psi to near 16 psi (the administrative limit is 17 psi) with the total filtrate volume (2.1E-4 psi/gal of filtrate). The linear behavior is due to the combined effect of a constant deposition of material that starts from the closed-end to the mid-section of the coalescer reducing the available surface area of the coalescer for fluid passage (linearly with filtrate volume) and the formation of a secondary emulsion (water in NG-CSSX) on the fibers of the coalescer media. Both effects reduced the coalescer porosity by at least 13% (after processing 48,700 gallons). Before the coalescer was removed, it was flushed with a 10 mM boric acid solution to reduce the dose level. To determine the nature of the deposited material, a physical and chemical analysis of the coalescer was conducted. Characterization of this coalescer revealed the adsorption of organic containing amines (secondary amides and primary amines), TiDG, degraded modifier (with no hydroxyl group), MaxCalix, and oxidized hydrocarbon (possibly from Isopar™L or from lubricant used at MCU) onto the coalescer media. The amide and amines are possibly from the decomposition of the suppressor (TiDG). The modifier and MaxCalix were the largest components of the deposited organic material, as determined from leaching the coalescer with dichloromethane. Both the Fourier-Transformed Infrared (FTIR) and Fourier-Transformed Hydrogen Nuclear Magnetic Resonance (FT-HNMR) results indicated that some of the modifier was degraded (missing their OH groups). The modifier was observed everywhere in the examined coalescer pieces (FTIR), while the TiDG and its decomposition products were observed at the

  19. Next Generation Extractants for Cesium Separation from High-Level Waste: From Fundamental Concepts to Site Implementation

    International Nuclear Information System (INIS)

    Moyer, Bruce A.; Bazelaire, Eve; Bonnesen, Peter V.; Bryan, Jeffrey C.; Delmau, Latitia H.; Engle, Nancy L.; Gorbunova, Maryna G.; Keever, Tamara J.; Levitskaia, Tatiana G.; Sachleben, Richard A.; Tomkins, Bruce A.; Bartsch, Richard A.

    2004-01-01

    General project objectives. This project seeks a fundamental understanding and major improvement in cesium separation from high-level waste by cesium-selective calixcrown extractants. Systems of particular interest involve novel solvent-extraction systems containing specific members of the calix[4]arene-crown-6 family, alcohol solvating agents, and alkylamines. Questions being addressed pertain to cesium binding strength, extraction selectivity, cesium stripping, and extractant solubility. Enhanced properties in this regard will specifically benefit cleanup projects funded by the USDOE Office of Environmental Management to treat and dispose of high-level radioactive wastes currently stored in underground tanks at the Savannah River Site (SRS), the Hanford site, and the Idaho National Environmental and Engineering Laboratory.1 The most direct beneficiary will be the SRS Salt Processing Project, which has recently identified the Caustic-Side Solvent Extraction (CSSX) process employing a calixcrown as its preferred technology for cesium removal from SRS high level tank waste.2 This technology owes its development in part to fundamental results obtained in this program

  20. Next Generation Extractants for Cesium Separation from High-Level Waste: From Fundamental Concepts to Site Implementation

    International Nuclear Information System (INIS)

    Moyer, Bruce A; Bazelaire, Eve; Bonnesen, Peter V.; Bryan, Jeffrey C.; Delmau, Laetitia H.; Engle, Nancy L.; Gorbunova, Maryna G.; Keever, Tamara J.; Levitskaia, Tatiana G.; Sachleben, Richard A.; Tomkins, Bruce A.; Bartsch, Richard A.; Talanov, Vladimir S.; Gibson, Harry W.; Jones, Jason W.; Hay, Benjamin P.

    2003-01-01

    This project seeks a fundamental understanding and major improvement in cesium separation from high-level waste by cesium-selective calixcrown extractants. Systems of particular interest involve novel solvent-extraction systems containing specific members of the calix[4]arene-crown-6 family, alcohol solvating agents, and alkylamines. Questions being addressed pertain to cesium binding strength, extraction selectivity, cesium stripping, and extractant solubility. Enhanced properties in this regard will specifically benefit cleanup projects funded by the USDOE Office of Environmental Management to treat and dispose of high-level radioactive wastes currently stored in underground tanks at the Savannah River Site (SRS), the Hanford site, and the Idaho National Environmental and Engineering Laboratory.1 The most direct beneficiary will be the SRS Salt Processing Project, which has recently identified the Caustic-Side Solvent Extraction (CSSX) process employing a calixcrown as its preferred technology for cesium removal from SRS high-level tank waste.2 This technology owes its development in part to fundamental results obtained in this program

  1. Increase in 4-coumaryl alcohol units during lignification in alfalfa (Medicago sativa) alters the extractability and molecular weight of lignin.

    Science.gov (United States)

    Ziebell, Angela; Gracom, Kristen; Katahira, Rui; Chen, Fang; Pu, Yunqiao; Ragauskas, Art; Dixon, Richard A; Davis, Mark

    2010-12-10

    The lignin content of biomass can impact the ease and cost of biomass processing. Lignin reduction through breeding and genetic modification therefore has potential to reduce costs in biomass-processing industries (e.g. pulp and paper, forage, and lignocellulosic ethanol). We investigated compositional changes in two low-lignin alfalfa (Medicago sativa) lines with antisense down-regulation of p-coumarate 3-hydroxylase (C3H) or hydroxycinnamoyl-CoA:shikimate hydroxycinnamoyltransferase (HCT). We investigated whether the difference in reactivity during lignification of 4-coumaryl alcohol (H) monomers versus the naturally dominant sinapyl alcohol and coniferyl alcohol lignin monomers alters the lignin structure. Sequential base extraction readily reduced the H monomer content of the transgenic lines, leaving a residual lignin greatly enriched in H subunits; the extraction profile highlighted the difference between the control and transgenic lines. Gel permeation chromatography of isolated ball-milled lignin indicated significant changes in the weight average molecular weight distribution of the control versus transgenic lines (CTR1a, 6000; C3H4a, 5500; C3H9a, 4000; and HCT30a, 4000).

  2. The Budget of the United States Government. Department of Defense Extract for Fiscal Years 1990 and 1991

    Science.gov (United States)

    1988-01-01

    8217110) pO : 1 0) @! lp C0)" cQ. cJ clj(% (% CZ.J c ’) m ’. c ’ (" Cv . 00 C=) c’) c" C4 J * n C" 0 OR CR D (’ Rcp .4 Ile V! C’J a: U) @0 C’ ’t cr 46 L...corrections; (3) a special outlier policy SEC. [808,7] S061!. Not to exceed $35.000,000 of the funds available for children’s hospitals and neonatal ...Continental United States, including design, architecture, and engi- 20580 (June 3, 1988); (4) a refinement to the DRGs for neonatal nearing services

  3. Massively Parallel Signal Processing using the Graphics Processing Unit for Real-Time Brain-Computer Interface Feature Extraction.

    Science.gov (United States)

    Wilson, J Adam; Williams, Justin C

    2009-01-01

    The clock speeds of modern computer processors have nearly plateaued in the past 5 years. Consequently, neural prosthetic systems that rely on processing large quantities of data in a short period of time face a bottleneck, in that it may not be possible to process all of the data recorded from an electrode array with high channel counts and bandwidth, such as electrocorticographic grids or other implantable systems. Therefore, in this study a method of using the processing capabilities of a graphics card [graphics processing unit (GPU)] was developed for real-time neural signal processing of a brain-computer interface (BCI). The NVIDIA CUDA system was used to offload processing to the GPU, which is capable of running many operations in parallel, potentially greatly increasing the speed of existing algorithms. The BCI system records many channels of data, which are processed and translated into a control signal, such as the movement of a computer cursor. This signal processing chain involves computing a matrix-matrix multiplication (i.e., a spatial filter), followed by calculating the power spectral density on every channel using an auto-regressive method, and finally classifying appropriate features for control. In this study, the first two computationally intensive steps were implemented on the GPU, and the speed was compared to both the current implementation and a central processing unit-based implementation that uses multi-threading. Significant performance gains were obtained with GPU processing: the current implementation processed 1000 channels of 250 ms in 933 ms, while the new GPU method took only 27 ms, an improvement of nearly 35 times.

  4. Characterization of solids deposited on the modular caustic-side solvent extraction unit (MCU) coalescer media removed in May and October 2014

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-01

    During routine maintenance, the coalescers utilized in the Modular Caustic-Side Solvent Extraction Unit (MCU) processing of Salt Batch 6 and a portion of Salt Batch 7 were sampled and submitted to the Savannah River National Laboratory (SRNL) for characterization, for the purpose of identifying solid phase constituents that may be accumulating in these coalescers. Specifically, two samples were received and characterized: A decontaminated salt solution (DSS) coalescer sample and a strip effluent (SE) coalescer sample. Aliquots of the samples were analyzed by XRD, Fourier Transform Infrared (FTIR) Spectroscopy, SEM, and EDS. Other aliquots of the samples were leached in acid solution, and the leachates were analyzed by ICP-AES. In addition, modeling was performed to provide a basis for comparison of the analytical results.

  5. Advanced scale conditioning agent and consolidated deposit extraction planning, application experience, and results at Comanche Peak Unit 2 and industrial super critical water oxidation waste reduction

    Energy Technology Data Exchange (ETDEWEB)

    Forney, M.; Ramaley, D. [Westinghouse Electric Company, Cranberry Township, PA (United States); Bryant, W. [Luminant Energy, Comanche Peak Nuclear Power Plant, Dallas, TX (United States)

    2015-07-01

    Advance Scale Conditioning Agent (ASCA) technology has been applied more than forty times worldwide since its inception in 2000. This technology has continually grown in popularity since its development due to the combination of several process benefits and minimal outage impacts. Comanche Peak Unit 2 applied a Top of Tubesheet (TTS) ASCA in 2014 for partial dissolution and softening of consolidated TTS collars. In addition to the ASCA application, a Consolidated Deposit Extraction (CODE) step was applied to the TTS. CODE is a chemical treatment technology that effectively targets and dissolves 'binding species' such as those containing aluminum and silicon from steam generator deposits. Since magnetite dissolution technologies are not wholly effective in removing consolidated TTS 'collars' CODE technology was developed to address this need in the industry. This paper will discuss both the Westinghouse and utility perspective on TTS ASCA/CODE application planning, site execution, and process results. (author)

  6. SALTSTONE VAULT CLASSIFICATION SAMPLES MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT/ACTINIDE REMOVAL PROCESS WASTE STREAM APRIL 2011

    Energy Technology Data Exchange (ETDEWEB)

    Eibling, R.

    2011-09-28

    Savannah River National Laboratory (SRNL) was asked to prepare saltstone from samples of Tank 50H obtained by SRNL on April 5, 2011 (Tank 50H sampling occurred on April 4, 2011) during 2QCY11 to determine the non-hazardous nature of the grout and for additional vault classification analyses. The samples were cured and shipped to Babcock & Wilcox Technical Services Group-Radioisotope and Analytical Chemistry Laboratory (B&W TSG-RACL) to perform the Toxic Characteristic Leaching Procedure (TCLP) and subsequent extract analysis on saltstone samples for the analytes required for the quarterly analysis saltstone sample. In addition to the eight toxic metals - arsenic, barium, cadmium, chromium, mercury, lead, selenium and silver - analytes included the underlying hazardous constituents (UHC) antimony, beryllium, nickel, and thallium which could not be eliminated from analysis by process knowledge. Additional inorganic species determined by B&W TSG-RACL include aluminum, boron, chloride, cobalt, copper, fluoride, iron, lithium, manganese, molybdenum, nitrate/nitrite as Nitrogen, strontium, sulfate, uranium, and zinc and the following radionuclides: gross alpha, gross beta/gamma, 3H, 60Co, 90Sr, 99Tc, 106Ru, 106Rh, 125Sb, 137Cs, 137mBa, 154Eu, 238Pu, 239/240Pu, 241Pu, 241Am, 242Cm, and 243/244Cm. B&W TSG-RACL provided subsamples to GEL Laboratories, LLC for analysis for the VOCs benzene, toluene, and 1-butanol. GEL also determines phenol (total) and the following radionuclides: 147Pm, 226Ra and 228Ra. Preparation of the 2QCY11 saltstone samples for the quarterly analysis and for vault classification purposes and the subsequent TCLP analyses of these samples showed that: (1) The saltstone waste form disposed of in the Saltstone Disposal Facility in 2QCY11 was not characteristically hazardous for toxicity. (2) The concentrations of the eight RCRA metals and UHCs identified as possible in the saltstone waste form were present at levels below the UTS. (3) Most of the

  7. Separation processes for the pretreatment of high-level nuclear wastes at the Savannah River site - 59291

    International Nuclear Information System (INIS)

    Hobbs, David; Peters, Thomas; Taylor-Pashow, Kathryn; Fondeur, Fernando; Nash, Charles; Fink, Samuel; Herman, David; Marra, Jim

    2012-01-01

    Document available in abstract form only. Full text of publication follows: Separation methods for the pretreatment of the high-level nuclear wastes (HLW) at the Savannah River Site (SRS) include the Caustic Side Solvent Extraction (CSSX) process for cesium and adsorption/ion exchange for the removal of cesium, strontium and alpha-emitting actinides. The CSSX process uses a calixarene extractant in combination with phase modifiers in a hydrocarbon diluent. Monosodium titanate (MST), a hydrous metal oxide, is the baseline material for the removal of strontium and alpha-emitting radionuclides (principally Pu-238, Pu-239, Pu-240 and Np-237). Two pretreatment facilities, the Modular Caustic Side Solvent Extraction Unit (MCU) and the Actinide Removal Process (ARP) facility began radioactive operations at SRS in 2008. Together these facilities can treat approximately 4 million liters of waste per year. The same separation processes are also planned for the much larger Salt Waste Processing Facility (SWPF). The SWPF, which has a design throughput of about 27 million liters per year, is under construction and scheduled to begin radioactive operations in 2014. Current R and D activities for the CSSX process are focused on implementing a new solvent system and stripping flowsheet that offers enhanced extraction and stripping of cesium. This next generation solvent system features a different calixarene extractant, uses caustic instead of nitric acid

  8. Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation.

    Science.gov (United States)

    Gharwade, Chandrakant Rambhau

    2016-01-01

    Follicular unit extraction (FUE) is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant). Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs). The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°-15°) of emergent hair from scalp skin, higher variance angle (15°-35°) between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions.

  9. Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation

    Directory of Open Access Journals (Sweden)

    Chandrakant Rambhau Gharwade

    2016-01-01

    Full Text Available Follicular unit extraction (FUE is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant. Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs. The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°–15° of emergent hair from scalp skin, higher variance angle (15°–35° between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions.

  10. The effect of plasma rich in growth factors combined with follicular unit extraction surgery for the treatment of hair loss: A pilot study.

    Science.gov (United States)

    Navarro, Roge M; Pino, Ander; Martinez-Andres, Asunción; Molina, Consuelo; Martinez, Ana María; Martinez, Nahikari; Orive, Gorka; Anitua, Eduardo

    2017-10-26

    Hair transplant surgery using follicular unit extraction technique (FUE) is a common surgical procedure for the treatment of severe hair loss. Blood-derived autologous growth factors have also proved to promote hair regeneration in patients with different types of alopecia. The aim of this study was to evaluate the safety and clinical efficacy of plasma rich in growth factors (PRGF) technology as an adjuvant therapy for FUE surgery in hair loss affected patients. The biologic potential of PRGF was firstly in vitro evaluated over follicular germinal matrix and dermal papilla cells. Afterward, fifteen patients were subjected to routine FUE procedure while 15 patients underwent FUE+PRGF therapy. PRGF group included intradermal injections of growth factors and follicular transfer unit (FTU) preservation in an autologous fibrin clot. Postsurgical patient satisfaction and clinical improvement were evaluated, and PRGF or saline-preserved hair grafts were histomorphometrically analyzed. Follicular cell proliferation and migration was induced after autologous growth factors treatment. PRGF-preserved FTUs presented higher bioactivity signals and improved integrity of perifollicular structures and extracellular matrix proteins such as collagen and elastic fibers. PRGF not only reduced the postsurgical crust healing and hair fixation period, but also decreased the inflammatory pain and itching sensation. This preliminary data demonstrate that PRGF is able to minimize the postsurgical follicle loss and potentiate the performance of grafted hairs. The fibrin clot not only acts as a protective barrier against environmental factors, but also provides a biologically active scaffold that induces resident cell proliferation and maintains an optimal integrity of the grafted hair. © 2017 Wiley Periodicals, Inc.

  11. Development of Effective Solvent Modifiers for the Solvent Extraction of Cesium from Alkaline High-Level Tank Waste

    International Nuclear Information System (INIS)

    Bonnesen, Peter V.; Delmau, Laetitia H.; Moyer, Bruce A.; Lumetta, Gregg J.

    2003-01-01

    A series of novel alkylphenoxy fluorinated alcohols were prepared and investigated for their effectiveness as modifiers in solvents containing calix(4)arene-bis-(tert-octylbenzo)-crown-6 for extracting cesium from alkaline nitrate media. A modifier that contained a terminal 1,1,2,2-tetrafluoroethoxy group was found to decompose following long-term exposure to warm alkaline solutions. However, replacement of the tetrafluoroethoxy group with a 2,2,3,3-tetrafluoropropoxy group led to a series of modifiers that possessed the alkaline stability required for a solvent extraction process. Within this series of modifiers, the structure of the alkyl substituent (tert-octyl, tert-butyl, tert-amyl, and sec-butyl) of the alkylphenoxy moiety was found to have a profound impact on the phase behavior of the solvent in liquid-liquid contacting experiments, and hence on the overall suitability of the modifier for a solvent extraction process. The sec-butyl derivative(1-(2,2,3,3-tetrafluoropropoxy)-3- (4-sec-butylphenoxy)-2-propanol) (Cs-7SB) was found to possess the best overall balance of properties with respect to third phase and coalescence behavior, cleanup following degradation, resistance to solids formation, and cesium distribution behavior. Accordingly, this modifier was selected for use as a component of the solvent employed in the Caustic-Side Solvent Extraction (CSSX) process for removing cesium from high level nuclear waste (HLW) at the U.S. Department of Energy's (DOE) Savannah River Site. In batch equilibrium experiments, this solvent has also been successfully shown to extract cesium from both simulated and actual solutions generated from caustic leaching of HLW tank sludge stored in tank B-110 at the DOE's Hanford Site.

  12. DWPF Flowsheet Studies with Simulants to Determine Modular Caustic Side Solvent Extraction Unit Solvent Partitioning and Verify Actinide Removal Process Incorporation Strategy

    International Nuclear Information System (INIS)

    Herman, C

    2006-01-01

    The Actinide Removal Process (ARP) facility and the Modular Caustic Side Solvent Extraction Unit (MCU) are scheduled to begin processing salt waste in fiscal year 2007. A portion of the streams generated in the salt processing facilities will be transferred to the Defense Waste Processing Facility (DWPF) to be incorporated in the glass matrix. Before the streams are introduced, a combination of impact analyses and research and development studies must be performed to quantify the impacts on DWPF processing. The Process Science and Engineering (PS and E) section of the Savannah River National Laboratory (SRNL) was requested via Technical Task Request (TTR) HLW/DWPF/TTR-2004-0031 to evaluate the impacts on DWPF processing. Simulant Chemical Process Cell (CPC) flowsheet studies have been performed using previous composition and projected volume estimates for the ARP sludge/monosodium titanate (MST) stream. Due to changes in the flammability control strategy for DWPF for salt processing, the incorporation strategy for ARP has changed and additional ARP flowsheet tests were necessary to validate the new processing strategy. The last round of ARP testing included the incorporation of the MCU stream and identified potential processing issues with the MCU solvent. The identified issues included the potential carry-over and accumulation of the MCU solvent components in the CPC condensers and in the recycle stream to the Tank Farm. Therefore, DWPF requested SRNL to perform additional MCU flowsheet studies to better quantify the organic distribution in the CPC vessels. The previous MCU testing used a Sludge Batch 4 (SB4) simulant since it was anticipated that both of these facilities would begin salt processing during SB4 processing. The same sludge simulant recipe was used in this round of ARP and MCU testing to minimize the number of changes between the two phases of testing so a better comparison could be made. ARP and MCU stream simulants were made for this phase of

  13. Demonstration and validation of automated agricultural field extraction from multi-temporal Landsat data for the majority of United States harvested cropland

    Science.gov (United States)

    Yan, L.; Roy, D. P.

    2014-12-01

    The spatial distribution of agricultural fields is a fundamental description of rural landscapes and the location and extent of fields is important to establish the area of land utilized for agricultural yield prediction, resource allocation, and for economic planning, and may be indicative of the degree of agricultural capital investment, mechanization, and labor intensity. To date, field objects have not been extracted from satellite data over large areas because of computational constraints, the complexity of the extraction task, and because consistently processed appropriate resolution data have not been available or affordable. A recently published automated methodology to extract agricultural crop fields from weekly 30 m Web Enabled Landsat data (WELD) time series was refined and applied to 14 states that cover 70% of harvested U.S. cropland (USDA 2012 Census). The methodology was applied to 2010 combined weekly Landsat 5 and 7 WELD data. The field extraction and quantitative validation results are presented for the following 14 states: Iowa, North Dakota, Illinois, Kansas, Minnesota, Nebraska, Texas, South Dakota, Missouri, Indiana, Ohio, Wisconsin, Oklahoma and Michigan (sorted by area of harvested cropland). These states include the top 11 U.S states by harvested cropland area. Implications and recommendations for systematic application to global coverage Landsat data are discussed.

  14. Extraction spectrophotometric analyzer

    International Nuclear Information System (INIS)

    Batik, J.; Vitha, F.

    1985-01-01

    Automation is discussed of extraction spectrophotometric determination of uranium in a solution. Uranium is extracted from accompanying elements in an HCl medium with a solution of tributyl phosphate in benzene. The determination is performed by measuring absorbance at 655 nm in a single-phase ethanol-water-benzene-tributyl phosphate medium. The design is described of an analyzer consisting of an analytical unit and a control unit. The analyzer performance promises increased productivity of labour, improved operating and hygiene conditions, and mainly more accurate results of analyses. (J.C.)

  15. Analytical Methods Development in Support of the Caustic Side Solvent Extraction System

    International Nuclear Information System (INIS)

    Maskarinec, M.P.

    2001-01-01

    The goal of the project reported herein was to develop and apply methods for the analysis of the major components of the solvent system used in the Caustic-Side Solvent Extraction Process (CSSX). These include the calix(4)arene, the modifier, 1-(2,2,3,3- tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol and tri-n-octylamine. In addition, it was an objective to develop methods that would allow visualization of other components under process conditions. These analyses would include quantitative laboratory methods for each of the components, quantitative analysis of expected breakdown products (4-see-butylphenol and di-n-octylamine), and qualitative investigations of possible additional breakdown products under a variety of process extremes. These methods would also provide a framework for process analysis should a pilot facility be developed. Two methods were implemented for sample preparation of aqueous phases. The first involves solid-phase extraction and produces quantitative recovery of the solvent components and degradation products from the various aqueous streams. This method can be automated and is suitable for use in radiation shielded facilities. The second is a variation of an established EPA liquid-liquid extraction procedure. This method is also quantitative and results in a final extract amenable to virtually any instrumental analysis. Two HPLC methods were developed for quantitative analysis. The first is a reverse-phase system with variable wavelength W detection. This method is excellent from a quantitative point of view. The second method is a size-exclusion method coupled with dual UV and evaporative light scattering detectors. This method is much faster than the reverse-phase method and allows for qualitative analysis of other components of the waste. For tri-n-octylamine and other degradation products, a GC method was developed and subsequently extended to GUMS. All methods have precision better than 5%. The combination of these methods

  16. Extraction process

    International Nuclear Information System (INIS)

    Rendall, J.S.; Cahalan, M.J.

    1979-01-01

    A process is described for extracting at least two desired constituents from a mineral, using a liquid reagent which produces the constituents, or compounds thereof, in separable form and independently extracting those constituents, or compounds. The process is especially valuable for the extraction of phosphoric acid and metal values from acidulated phosphate rock, the slurry being contacted with selective extractants for phosphoric acid and metal (e.g. uranium) values. In an example, uranium values are oxidized to uranyl form and extracted using an ion exchange resin. (U.K.)

  17. DEMONSTRATION OF THE NEXT-GENERATION CAUSTIC-SIDE SOLVENT EXTRACTION SOLVENT WITH 2-CM CENTRIFUGAL CONTRACTORS USING TANK 49H WASTE AND WASTE SIMULANT

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, R.; Peters, T.; Crowder, M.; Caldwell, T.; Pak, D; Fink, S.; Blessing, R.; Washington, A.

    2011-09-27

    Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet using MaxCalix for the decontamination of high level waste (HLW). The demonstration was completed using a 12-stage, 2-cm centrifugal contactor apparatus at the Savannah River National Laboratory (SRNL). This represents the first CSSX process demonstration of the MaxCalix solvent system with Savannah River Site (SRS) HLW. Two tests lasting 24 and 27 hours processed non-radioactive simulated Tank 49H waste and actual Tank 49H HLW, respectively. Conclusions from this work include the following. The CSSX process is capable of reducing {sup 137}Cs in high level radioactive waste by a factor of more than 40,000 using five extraction, two scrub, and five strip stages. Tests demonstrated extraction and strip section stage efficiencies of greater than 93% for the Tank 49H waste test and greater than 88% for the simulant waste test. During a test with HLW, researchers processed 39 liters of Tank 49H solution and the waste raffinate had an average decontamination factor (DF) of 6.78E+04, with a maximum of 1.08E+05. A simulant waste solution ({approx}34.5 liters) with an initial Cs concentration of 83.1 mg/L was processed and had an average DF greater than 5.9E+03, with a maximum DF of greater than 6.6E+03. The difference may be attributable to differences in contactor stage efficiencies. Test results showed the solvent can be stripped of cesium and recycled for {approx}25 solvent turnovers without the occurrence of any measurable solvent degradation or negative effects from minor components. Based on the performance of the 12-stage 2-cm apparatus with the Tank 49H HLW, the projected DF for MCU with seven extraction, two scrub, and seven strip stages operating at a nominal efficiency of 90% is {approx}388,000. At 95% stage efficiency, the DF in MCU would be {approx}3.2 million. Carryover of organic solvent in aqueous streams (and aqueous in organic

  18. Through wall degradation problem of the turbine extraction steam drain piping due to liquid drop impingement and measures taken for this problem at Fukushima Dai-ichi Nuclear Power Plant Unit 6

    International Nuclear Information System (INIS)

    Inagaki, Takeyuki; Kobayashi, Teruaki; Shimada, Shigeru; Inoue, Ryousuke; Usuba, Satoshi; Kimura, Takeo

    2011-01-01

    Through wall degradation was found on the extraction steam drain piping of Unit 6 of Fukushima Dai-ichi Nuclear Power Plant owned by Tokyo Electric Power Company after replacement of the turbine rotors with those of higher thermal efficiency. The mechanism of this degradation was loss of material due to liquid drop impingement. Since the estimated life time of the piping based on wall thickness measurements before the replacement was at least 9 years, the rapid wall thinning occurred after the replacement. This paper describes a summary of the phenomenon, its degradation mechanism and root cause, a temporary measurement taken for an immediate action and permanent measures taken during the next refueling outage. (author)

  19. Solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, D.M.; Latimer, E.G.

    1988-01-05

    It is an object of this invention to provide for the demetallization and general upgrading of heavy oil via a solvent extracton process, and to improve the efficiency of solvent extraction operations. The yield and demetallization of product oil form heavy high-metal content oil is maximized by solvent extractions which employ either or all of the following techniques: premixing of a minor amount of the solvent with feed and using countercurrent flow for the remaining solvent; use of certain solvent/free ratios; use of segmental baffle tray extraction column internals and the proper extraction column residence time. The solvent premix/countercurrent flow feature of the invention substantially improves extractions where temperatures and pressures above the critical point of the solvent are used. By using this technique, a greater yield of extract oil can be obtained at the same metals content or a lower metals-containing extract oil product can be obtained at the same yield. Furthermore, the premixing of part of the solvent with the feed before countercurrent extraction gives high extract oil yields and high quality demetallization. The solvent/feed ratio features of the invention substanially lower the captial and operating costs for such processes while not suffering a loss in selectivity for metals rejection. The column internals and rsidence time features of the invention further improve the extractor metals rejection at a constant yield or allow for an increase in extract oil yield at a constant extract oil metals content. 13 figs., 3 tabs.

  20. Uranium refining by solvent extraction

    International Nuclear Information System (INIS)

    Kraikaew, J.

    1996-01-01

    The yellow cake refining was studied in both laboratory and semi-pilot scales. The process units mainly consist of dissolution and filtration, solvent extraction, and precipitation and filtration. Effect of flow ratio (organic flow rate/ aqueous flow rate) on working efficiencies of solvent extraction process was studied. Detailed studies were carried out on extraction, scrubbing and stripping processes. Purity of yellow cake product obtained is high as 90.32% U 3 O 8

  1. Extraction method

    International Nuclear Information System (INIS)

    Stary, J.; Kyrs, M.; Navratil, J.; Havelka, S.; Hala, J.

    1975-01-01

    Definitions of the basic terms and of relations are given and the knowledge is described of the possibilities of the extraction of elements, oxides, covalent-bound halogenides and heteropolyacids. Greatest attention is devoted to the detailed analysis of the extraction of chelates and ion associates using diverse agents. For both types of compounds detailed conditions are given of the separation and the effects of the individual factors are listed. Attention is also devoted to extractions using mixtures of organic agents, the synergic effects thereof, and to extractions in non-aqueous solvents. The effects of radiation on extraction and the main types of apparatus used for extractions carried out in the laboratory are described. (L.K.)

  2. Vacuum extraction

    DEFF Research Database (Denmark)

    Maagaard, Mathilde; Oestergaard, Jeanett; Johansen, Marianne

    2012-01-01

    Objectives. To develop and validate an Objective Structured Assessment of Technical Skills (OSATS) scale for vacuum extraction. Design. Two-part study design: Primarily, development of a procedure-specific checklist for vacuum extraction. Hereafter, validation of the developed OSATS scale for vac...

  3. Electromembrane extraction

    DEFF Research Database (Denmark)

    Huang, Chuixiu; Chen, Zhiliang; Gjelstad, Astrid

    2017-01-01

    Electromembrane extraction (EME) was inspired by solid-phase microextraction and developed from hollow fiber liquid-phase microextraction in 2006 by applying an electric field over the supported liquid membrane (SLM). EME provides rapid extraction, efficient sample clean-up and selectivity based...

  4. Passive vapor extraction feasibility study

    International Nuclear Information System (INIS)

    Rohay, V.J.

    1994-01-01

    Demonstration of a passive vapor extraction remediation system is planned for sites in the 200 West Area used in the past for the disposal of waste liquids containing carbon tetrachloride. The passive vapor extraction units will consist of a 4-in.-diameter pipe, a check valve, a canister filled with granular activated carbon, and a wind turbine. The check valve will prevent inflow of air that otherwise would dilute the soil gas and make its subsequent extraction less efficient. The granular activated carbon is used to adsorb the carbon tetrachloride from the air. The wind turbine enhances extraction rates on windy days. Passive vapor extraction units will be designed and operated to meet all applicable or relevant and appropriate requirements. Based on a cost analysis, passive vapor extraction was found to be a cost-effective method for remediation of soils containing lower concentrations of volatile contaminants. Passive vapor extraction used on wells that average 10-stdft 3 /min air flow rates was found to be more cost effective than active vapor extraction for concentrations below 500 parts per million by volume (ppm) of carbon tetrachloride. For wells that average 5-stdft 3 /min air flow rates, passive vapor extraction is more cost effective below 100 ppm

  5. Bevalac extraction

    International Nuclear Information System (INIS)

    Kalnins, J.G.; Krebs, G.; Tekawa, M.; Cowles, D.; Byrne, T.

    1992-02-01

    This report will describe some of the general features of the Bevatron extraction system, primarily the dependence of the beam parameters and extraction magnet currents on the Bevalac field. The extraction magnets considered are: PFW, XPl, XP2, XS1, XS2, XM1, XM2, XM3, XQ3A and X03B. This study is based on 84 past tunes (from 1987 to the present) of various ions (p,He,O,Ne,Si,S,Ar,Ca,Ti,Fe,Nb,La,Au and U), for Bevalac fields from 1.749 to 12.575 kG, where all tunes included a complete set of beam line wire chamber pictures. The circulating beam intensity inside the Bevalac is measured with Beam Induction Electrodes (BIE) in the South Tangent Tank. The extracted beam intensity is usually measured with the Secondary Emission Monitor (SEM) in the F1-Box. For most of the tunes the extraction efficiency, as given by the SEM/BIE ratio, was not recorded in the MCR Log Book, but plotting the available Log Book data as a function of the Bevalac field, see Fig.9, we find that the extraction efficiency is typically between 30->60% with feedback spill

  6. EXPANDING EXTRACTIONS

    NARCIS (Netherlands)

    Dietzenbacher, Erik; Lahr, Michael L.

    2013-01-01

    In this paper, we generalize hypothetical extraction techniques. We suggest that the effect of certain economic phenomena can be measured by removing them from an input-output (I-O) table and by rebalancing the set of I-O accounts. The difference between the two sets of accounts yields the

  7. OPERATIONS REVIEW OF THE SAVANNAH RIVER SITE INTEGRATED SALT DISPOSITION PROCESS - 11327

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T.; Poirier, M.; Fondeur, F.; Fink, S.; Brown, S.; Geeting, M.

    2011-02-07

    The Savannah River Site (SRS) is removing liquid radioactive waste from its Tank Farm. To treat waste streams that are low in Cs-137, Sr-90, and actinides, SRS developed the Actinide Removal Process and implemented the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). The Actinide Removal Process contacts salt solution with monosodium titanate to sorb strontium and select actinides. After monosodium titanate contact, the resulting slurry is filtered to remove the monosodium titanate (and sorbed strontium and actinides) and entrained sludge. The filtrate is transferred to the MCU for further treatment to remove cesium. The solid particulates removed by the filter are concentrated to {approx} 5 wt %, washed to reduce the sodium concentration, and transferred to the Defense Waste Processing Facility for vitrification. The CSSX process extracts the cesium from the radioactive waste using a customized solvent to produce a Decontaminated Salt Solution (DSS), and strips and concentrates the cesium from the solvent with dilute nitric acid. The DSS is incorporated in grout while the strip acid solution is transferred to the Defense Waste Processing Facility for vitrification. The facilities began radiological processing in April 2008 and started processing of the third campaign ('MarcoBatch 3') of waste in June 2010. Campaigns to date have processed {approx}1.2 million gallons of dissolved saltcake. Savannah River National Laboratory (SRNL) personnel performed tests using actual radioactive samples for each waste batch prior to processing. Testing included monosodium titanate sorption of strontium and actinides followed by CSSX batch contact tests to verify expected cesium mass transfer. This paper describes the tests conducted and compares results from facility operations. The results include strontium, plutonium, and cesium removal, cesium concentration, and organic entrainment and recovery data. Additionally, the poster describes lessons learned during

  8. Mineral extraction and transport device

    Energy Technology Data Exchange (ETDEWEB)

    Plaga, K.

    1991-08-21

    A device for the extraction and transport of stratified mineral deposits notably coal, having a transport run with lengths of transport troughing, an extraction run with lengths of extraction troughing, and a power-driven traction chain guided round return devices and carrying extraction bodies together with optional transport units. The transport and extraction troughing have guide members on which the extraction bodies and the transport units are guided with the aid of guide formations. Each extraction body consists of a headpiece having two laterally protruding guide formations, and an endpiece having two laterally protruding guide formations and a centrepiece. The headpiece and the endpiece are swivellably linked to the centrepiece through an axis running substantially at right angles to the traction axis of the traction chain and substantially at right angles to the floor of the lengths of transport troughing in the transport run. The centrepiece has an additional articulation about an axis substantially orthogonal to the swivel axis of the headpiece and the endpiece. Guide members are additionally provided in the vicinity of the return devices whereby the guide formations on each headpiece and endpiece receive continued guidance.

  9. Uranium chemistry research unit

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    The initial field of research of this Unit, established in 1973, was the basic co-ordination chemistry of uranium, thorium, copper, cobalt and nickel. Subsequently the interest of the Unit extended to extractive metallurgy relating to these metals. Under the term 'co-ordination chemistry' is understood the interaction of the central transition metal ion with surrounding atoms in its immediate vicinity (within bonding distance) and the influence they have on each other - for example, structural studies for determining the number and arrangement of co-ordinated atoms and spectrophotometric studies to establish how the f electron energy levels of uranium are influenced by the environment. New types of uranium compounds have been synthesized and studied, and the behaviour of uranium ions in non-aqueous systems has also received attention. This work can be applied to the development and study of extractants and new extractive processes for uranium

  10. Antibacterial activities of the crude ethanol extracts of medicinal ...

    African Journals Online (AJOL)

    STORAGESEVER

    2010-07-05

    Jul 5, 2010 ... extract. On the other hand, the antimicrobial activity was mainly a function of their chemical ... determine antibacterial properties of these plants extracts .... vancomycin (30 µg); PEN= penicillin G (10 unit); AMP = ampicillin (5.

  11. Extracting oils

    Energy Technology Data Exchange (ETDEWEB)

    Patart, G

    1926-03-15

    In the hydrogenation or extraction of by-products from organic substances at high temperatures and pressures, the gases or liquids, or both, used are those which are already heated and compressed during industrial operations such as exothermic synthesizing reactions such as the production of methanol from hydrogen and carbon monoxide in a catalytic process. Gases from this reaction may be passed upwardly through a digester packed with pine wood while liquid from the same catalytic process is passed downwardly through the material. The issuing liquid contains methanol, pine oil, acetone, isopropyl alcohol, and acetic acid. The gases contain additional hydrogen, carbon monoxide, methane, ethylene, and its homologs which are condensed upon the catalyser to liquid hydrocarbons. Petroleum oils and coal may be treated similarly.

  12. Interface unit

    NARCIS (Netherlands)

    Keyson, D.V.; Freudenthal, A.; De Hoogh, M.P.A.; Dekoven, E.A.M.

    2001-01-01

    The invention relates to an interface unit comprising at least a display unit for communication with a user, which is designed for being coupled with a control unit for at least one or more parameters in a living or working environment, such as the temperature setting in a house, which control unit

  13. Uranium extraction technology

    International Nuclear Information System (INIS)

    1993-01-01

    In 1983 the Nuclear Energy Agency of the Organisation for Economic Co-operation and Development (OECD/NEA) and the IAEA jointly published a book on Uranium Extraction Technology. A primary objective of this report was to document the significant technological developments that took place during the 1970s. The purpose of this present publication is to update and expand the original book. It includes background information about the principle of the unit operations used in uranium ore processing and summarizes the current state of the art. The publication also seeks to preserve the technology and the operating 'know-how' developed over the past ten years. This publication is one of a series of Technical Reports on uranium ore processing that have been prepared by the Division of Nuclear Fuel Cycle and Waste Management at the IAEA. A complete list of these reports is included as an addendum. Refs, figs and tabs

  14. Solvent Carryover Characterization and Recovery for a 10-inch Single Stage Centrifugal Contactor

    International Nuclear Information System (INIS)

    Lentsch, R.D.; Stephens, A.B.; Leung, D.T.; Baffling, K.E.; Harmon, H.D.; Suggs, P.C.

    2006-01-01

    A test program has been performed to characterize the organic solvent carryover and recovery from centrifugal contactors in the Caustic-side Solvent Extraction (CSSX) process. CSSX is the baseline design for removing cesium from salt solutions for Department of Energy (DOE) Savannah River Site's Salt Waste Processing Facility. CSSX uses a custom solvent to extract cesium from the salt solution in a series of single stage centrifugal contactors. Meeting the Waste Acceptance Criteria at the Defense Waste Processing Facility and Saltstone, as well as plant economics, dictate that solvent loss should be kept to a minimum. Solvent droplet size distribution in the aqueous outlet streams of the CSSX contactors is of particular importance to the design of solvent recovery equipment. Because insufficient solvent droplet size data existed to form a basis for the recovery system design, DOE funded the CSSX Solvent Carryover Characterization and Recovery Test (SCCRT). This paper presents the droplet size distribution of solvent and concentration in the contactor aqueous outlet streams as a function of rotor speed, bottom plate type, and flow rate. It also presents the performance data of a prototype coalescer. (authors)

  15. Extractive {sup 90}Y generator

    Energy Technology Data Exchange (ETDEWEB)

    Kodina, G.E. [State Scientific Center, Moscow (Russian Federation). Institute of Giophysics; Korpusov, G.V.; Filyanin, A.T. [Russian Academy of Sciences, Moscow (Russian Federation). Institute of Physical Chemistry

    1997-10-01

    The generator for {sup 90}Y production is made up of two units - an extractive unit and a unit for deep purification. Contrary to the well-known methods of {sup 90}Y separation two mineral acids are used in the developed technology. The solutions of nitric acid are used for preliminary separation of {sup 90}Y and the solutions of hydrochloric acid are used for the deep purification of {sup 90}Y from {sup 90}Sr and stripping. The optimum conditions for carrying out this technology were found. The following results are reported: the carry-over of the stationary phase is excluded in this generator; the separation time is 30-60 minutes; the yield of the final product is not less than 95%; impurity of {sup 90}Sr is not more than 10{sup -9-}-{sup -10}%; the content of the chemical (nonactive) impurities is not more than the allowed one for radiopharmaceuticals 4 refs., 4 tabs., 5 figs.

  16. Method of gentle extraction and subsequent concentration at low temperature of natural compounds in the extract from plants

    DEFF Research Database (Denmark)

    Norddahl, Birgir; Christensen, Knud Villy

    2007-01-01

    A unit performing a simple and effective way to extract active phytochemicals from the plant specimens has been developed. The unit is mobile enabling operation near the place of collection of plant specimens reducing waste of potential valuable phytochemicals. The design is based on counter...... as solid/liquid extraction is developed on the basis similar to sugar extraction from sugar beets, albeit in a much more compact form. The equipment has been tested on extraction of ethereal oils from dried, stored oregano and extraction of natural compounds from freshly harvested Artemesia with 96% Et......OH as the solvent. Preliminary results from a continuous oregano extraction show efficiency between 55% and 85% of a more ideal laboratory batch extraction of a marker compound like carvacrol, which is most abundant in the ethereal oil. The operation can be repeated with another liquid in order to extract compounds...

  17. Generating Units

    Data.gov (United States)

    Department of Homeland Security — Generating Units are any combination of physically connected generators, reactors, boilers, combustion turbines, and other prime movers operated together to produce...

  18. Sterically hindered solvent extractants

    International Nuclear Information System (INIS)

    Solka, J.L.; Reis, A.H. Jr.; Mason, G.W.; Lewey, S.M.; Peppard, D.F.

    1978-01-01

    Di-t-pentylphosphinic acid, [C(CH 3 ) 2 (CH 2 CH 3 )] 2 PO(OH), H[Dt-PeP], has been shown by single-crystal X-ray diffraction data to be dimeric in the solid state. H[Dt-PeP] crystallizes in the centro-symmetric orthorhombic space group, Cmca, with unit cell parameters, a = 17.694(7), b = 11.021(4), and c = 13.073(5) A, and Z = 8, indicating that the molecule must conform to a crystallographic mirror plane or 2-fold axis. A measured density of 1.088 g/cm 3 is in good agreement with a calculated value of 1.074 g/cm 3 for a unit cell volume of 2549.3(A) 3 and a formula weight of 206.25 g. A total of 646 three-dimensional X-ray data were collected on an automated XRD-490 G.E. diffractometer. The structure was solved using a combination of direct methods, Patterson, Fourier, and least-squares refinement techniques. Refinement of the data indicates that H[Dt-PeP] is dimeric, and contains a mirror plane in which the hydrogen-bonded, eight-membered ring lies. A structural disorder involving principally the ethylene carbon but affecting the methyl carbons as well precluded a precise determination of the carbon positions and severely reduced the precision of the final refinement. In the liquid-liquid extraction system consisting of a solution of H[Dt-PeP] in benzene vs an acidic aqueous chloride phase, the extraction of UO 2 2+ follows the stoichiometry: UO 2 sub(A) 2+ + 2(HY) 2 subO = UO 2 (HY 2 ) 2 sub(O) + 2Hsub(A) + where (HY) 2 represents the dimer of H[Dt-PeP] and A and O represent the mutually equilibrated aqueous and organic phases. The expression for the distribution ratio, k, for UO 2 2+ is given. (author)

  19. Extract of Acanthospermum hispidum

    African Journals Online (AJOL)

    Administrator

    quantitatively. Acute toxicity study of the extract was conducted, and diabetic rats induced using alloxan (80 mg/kg ... Type 2 diabetes is one of the leading causes of mortality and ..... (2011): Phytochemical screening and extraction - A review.

  20. Extracts against Various Pathogens

    Directory of Open Access Journals (Sweden)

    Ritika Chauhan

    2013-07-01

    The present study shows that tested lichen Parmotrema sp. extracts demonstrated a strong antimicrobial effect. That suggests the active components from methanol extracts of the investigated lichen Parmotrema sp. can be used as natural antimicrobial agent against pathogens.

  1. using Supercritical Fluid Extraction

    African Journals Online (AJOL)

    Methods: Supercritical CO2 extraction technology was adopted in this experiment to study the process of extraction of volatile oil from Polygonatum odoratum while gas chromatograph-mass spectrometer ..... Saponin rich fractions from.

  2. Unit Manning

    National Research Council Canada - National Science Library

    McGinniss, Mike

    2003-01-01

    .... This decision combines two crucial initiatives: first, transforming the Army from an individual soldier replacement system to a unit manning system that enhances cohesion and keeps trained soldiers, leaders, and commanders together longer, thereby...

  3. Detector Unit

    CERN Multimedia

    1960-01-01

    Original detector unit of the Instituut voor Kernfysisch Onderzoek (IKO) BOL project. This detector unit shows that silicon detectors for nuclear physics particle detection were already developed and in use in the 1960's in Amsterdam. Also the idea of putting 'strips' onto the silicon for high spatial resolution of a particle's impact on the detector were implemented in the BOL project which used 64 of these detector units. The IKO BOL project with its silicon particle detectors was designed, built and operated from 1965 to roughly 1977. Detector Unit of the BOL project: These detectors, notably the ‘checkerboard detector’, were developed during the years 1964-1968 in Amsterdam, The Netherlands, by the Natuurkundig Laboratorium of the N.V. Philips Gloeilampen Fabrieken. This was done in close collaboration with the Instituut voor Kernfysisch Onderzoek (IKO) where the read-out electronics for their use in the BOL Project was developed and produced.

  4. Drilling unit

    Energy Technology Data Exchange (ETDEWEB)

    Umanchik, N P; Demin, A V; Khrustalev, N N; Linnik, G N; Lovchev, S V; Rozin, M M; Sidorov, R V; Sokolov, S I; Tsaregradskiy, Yu P

    1981-01-01

    A drilling unit is proposed which includes a hydraulic lifter, hydraulic multiple-cylinder pump with valve distribution and sectional drilling pump with separators of the working and flushing fluid. In order to reduce metal consumption and the overall dimensions of the drilling unit, the working cavity of each cylinder of the hydraulic multiple-cylinder pump is equipped with suction and injection valves and is hydraulically connected to the working cavity by one of the sections of the drilling pump.

  5. Information extraction system

    Science.gov (United States)

    Lemmond, Tracy D; Hanley, William G; Guensche, Joseph Wendell; Perry, Nathan C; Nitao, John J; Kidwell, Paul Brandon; Boakye, Kofi Agyeman; Glaser, Ron E; Prenger, Ryan James

    2014-05-13

    An information extraction system and methods of operating the system are provided. In particular, an information extraction system for performing meta-extraction of named entities of people, organizations, and locations as well as relationships and events from text documents are described herein.

  6. SOLVENT FIRE BY-PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D; Samuel Fink, S

    2006-05-22

    Southwest Research Institute (SwRI) conducted a burn test of the Caustic-Side Solvent Extraction (CSSX) solvent to determine the combustion products. The testing showed hydrogen fluoride gas is not a combustion product from a solvent fire when up to 70% of the solvent is consumed. The absence of HF in the combustion gases may reflect concentration of the modifier containing the fluoride groups in the unburned portion. SwRI reported results for other gases (CO, HCN, NOx, formaldehyde, and hydrocarbons). The results, with other supporting information, can be used for evaluating the consequences of a facility fire involving the CSSX solvent inventory.

  7. Early uranium mining in the United States

    International Nuclear Information System (INIS)

    Hahne, F.J.

    1990-01-01

    Uranium mining in the United States is closer to 100 years old than to the 200 years since the discovery of the element. Even then, for much of this time the rock was brought out of the ground for reasons other than its uranium content. The history of the US uranium industry is divided into five periods which follow roughly chronologically upon one another, although there is some overlap. The periods cover: uranium use in glass and ceramics; radium extraction; vanadium extraction; government uranium extraction and commercial extraction. (author)

  8. Full scale solvent extraction remedial results

    International Nuclear Information System (INIS)

    Cash, A.B.

    1992-01-01

    Sevenson Extraction Technology, Inc. has completed the development of the Soil Restoration Unit (initially developed by Terra-Kleen Corporation), a mobile, totally enclosed solvent extraction treatment facility for the removal of organic contaminated media is greater by a closed loop, counter current process that recycles all solvents. The solvents used are selected for the individual site dependant upon the contaminants, such as PCB's, oil, etc. and the soil conditions. A mixture of up to fourteen non-toxic solvents can be used for complicated sites. The full scale unit has been used to treat one superfund site, the Traband Site in Tulsa, Oklahoma, and is currently treating another superfund site, the Pinette's Salvage Yard Site in Washburn, Maine. The full scale Soil Restoration Unit has also been used at a non-superfund site, as part of a TSCA Research and Development permit. The results from these sites will be discussed in brief herein, and in more detail in the full paper

  9. [Conservation Units.

    Science.gov (United States)

    Texas Education Agency, Austin.

    Each of the six instructional units deals with one aspect of conservation: forests, water, rangeland, minerals (petroleum), and soil. The area of the elementary school curriculum with which each correlates is indicated. Lists of general and specific objectives are followed by suggested teaching procedures, including ideas for introducing the…

  10. Extractability of Thevetia peruviana glycosides with alcohol mixture

    African Journals Online (AJOL)

    SERVER

    2007-09-19

    Sep 19, 2007 ... Nitrogen extraction of defatted rapeseed with particular reference to United Kingdom rapeseed meal. J. Sci. Food Agric. 36: 520–530. Finnigan TJA, Lewis MJ (1988). Ethanolic Extraction of Commercial. Rapeseed Meal in the Production of Protein Concentrate of Reduced. Glucosinolate Content. J. Sci.

  11. Extraction with supercritical gases

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, G M; Wilke, G; Stahl, E

    1980-01-01

    The contents of this book derives from a symposium on the 5th and 6th of June 1978 in the ''Haus der Technik'' in Essen. Contributions were made to separation with supercritical gases, fluid extraction of hops, spices and tobacco, physicochemical principles of extraction, phase equilibria and critical curves of binary ammonia-hydrocarbon mixtures, a quick method for the microanalytical evaluation of the dissolving power of supercritical gases, chromatography with supercritical fluids, the separation of nonvolatile substances by means of compressed gases in countercurrent processes, large-scale industrial plant for extraction with supercritical gases, development and design of plant for high-pressure extraction of natural products.

  12. Exhaustive extraction of peptides by electromembrane extraction

    DEFF Research Database (Denmark)

    Huang, Chuixiu; Gjelstad, Astrid; Pedersen-Bjergaard, Stig

    2015-01-01

    trifluoroacetate, and leu-enkephalin were extracted from 600 μL of 25 mM phosphate buffer (pH 3.5), through a supported liquid membrane (SLM) containing di-(2-ethylhexyl)-phosphate (DEHP) dissolved in an organic solvent, and into 600 μL of an acidified aqueous acceptor solution using a thin flat membrane-based EME...

  13. Plant extraction process

    DEFF Research Database (Denmark)

    2006-01-01

    A method for producing a plant extract comprises incubating a plant material with an enzyme composition comprising a lipolytic enzyme.......A method for producing a plant extract comprises incubating a plant material with an enzyme composition comprising a lipolytic enzyme....

  14. AGS slow extraction improvements

    International Nuclear Information System (INIS)

    Glenn, J.W.; Smith, G.A.; Sandberg, J.N.; Repeta, L.; Weisberg, H.

    1979-01-01

    Improvement of the straightness of the F5 copper septum increased the AGS slow extraction efficiency from approx. 80% to approx. 90%. Installation of an electrostatic septum at H2O, 24 betatron wavelengths upstream of F5, further improved the extraction efficiency to approx. 97%

  15. Extraction of metal values

    Energy Technology Data Exchange (ETDEWEB)

    Dalton, R F

    1988-10-19

    Metal values (especially uranium values) are extracted from aqueous solutions of metal oxyions in the absence of halogen ion using an imidazole of defined formula. Especially preferred extractants are 1-alkyl imidazoles and benzimidazoles having from 7 to 25 carbon atoms in the alkyl group.

  16. (Lamiaceae) root extracts

    African Journals Online (AJOL)

    Purpose: To evaluate the larvicidal, nematicidal, antifeedant, and antifungal effects of 10 solvent extracts of Mentha spicata root. Methods: Ten solvent extracts were investigated for their total flavonoid and phenolic content and screened for larvicidal, nematicidal, antifeedant, and antifungal activities. The total phenolic ...

  17. Depleted uranium processing and fluorine extraction

    International Nuclear Information System (INIS)

    Laflin, S.T.

    2010-01-01

    Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds (730 million kilograms) of DUF_6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF_6 tails management. (author)

  18. Catalog solvent extraction: anticipate process adjustments

    International Nuclear Information System (INIS)

    Campbell, S.G.; Brass, E.A.; Brown, S.J.; Geeting, M.W.

    2008-01-01

    The Modular Caustic-Side Solvent Extraction Unit (MCU) utilizes commercially available centrifugal contactors to facilitate removal of radioactive cesium from highly alkaline salt solutions. During the fabrication of the contactor assembly, demonstrations revealed a higher propensity for foaming than was initially expected. A task team performed a series of single-phase experiments that revealed that the shape of the bottom vanes and the outer diameter of those vanes are key to the successful deployment of commercial contactors in the Caustic-Side Solvent Extraction Process. (authors)

  19. Microcontroller Unit

    International Nuclear Information System (INIS)

    Tulaev, A.B.

    1994-01-01

    The general purpose micro controller unit based on 8-bit single-chip microcomputer of the MCS-51 family is described. The controller has the data and program memories, a serial interface and an external bus for functional I/O extensions. The controller consists of a microcomputer chip, up to 4 ROM-RAM chips and 10 SSI and MSI chips, and it measures 160x120 mm. Both hardware and software micro system debugging tools are described. (author). 8 refs., 1 fig., 1 tab

  20. Assembly of contactors-separators in an extraction unit

    International Nuclear Information System (INIS)

    Beaujard, Jean; Menes, J.-C.; Ravoire, Jean.

    1977-01-01

    A description is given of an assembly of contactors-separators of an installation in which a transfer of mass or an isotope exchange occurs between two non miscible phases, characterized in that the contactors-separators are associated in m lines and n columns, one of the phases issuing from a contactor-separator being sent directly to the next contactor-separator of the same line, whilst the other phase, issuing from the same contactor-separator is sent directly to the next contactor-separator of the same column, each of the m lines and n columns being provided with one only pumping facility, the instantaneous flow rate of each phase, at the intake and outlet of each contactor-separator being appreciably identical [fr

  1. Extraction chromatography of actinides

    International Nuclear Information System (INIS)

    Muller, W.

    1978-01-01

    Extraction chromatography of actinides in the oxidation state from 2 to 6 is reviewed. Data on using neutral (tbp), basic (substituted ammonium salts) and acidic [di-(2-ethylhexyl)-phosphoric acid (D2EHPA)] extracting agents ketones, esters, alcohols and β-diketones in this method are given. Using the example of actinide separation using D2EHPA, discussed are factors influencing the efficiency of their chromatography separation (nature and particle size of the carrier materials, extracting agents amount on the carrier, temperature and elution rate)

  2. Multimedia Information Extraction

    CERN Document Server

    Maybury, Mark T

    2012-01-01

    The advent of increasingly large consumer collections of audio (e.g., iTunes), imagery (e.g., Flickr), and video (e.g., YouTube) is driving a need not only for multimedia retrieval but also information extraction from and across media. Furthermore, industrial and government collections fuel requirements for stock media access, media preservation, broadcast news retrieval, identity management, and video surveillance.  While significant advances have been made in language processing for information extraction from unstructured multilingual text and extraction of objects from imagery and vid

  3. The organophosphorus extractants

    International Nuclear Information System (INIS)

    Zaoul, B.; Attou, M.; Azzouz, A.

    1989-07-01

    This work consists in a bibliographic review dealing with phosphorus and organophosphorus compounds chemistry and especially with the main extracting agents used in uranium ore treatment. In this context, a special interest is devoted to TBP, D 2 EHPA and TOPO. The content of this work is based on a large bibliography including cca. One hundred references related to many aspects concerning as well the nomenclature, the classification and the chemical structures of the organophosphorus compounds as synthesis methods, purification and analysis of the main extracting agents used in uranium extraction

  4. Substoichiometric extraction of phosphorus

    International Nuclear Information System (INIS)

    Shigematsu, T.; Kudo, K.

    1981-01-01

    A study of the substoichiometric extraction of phosphorus is described. Phosphorus was extracted in the form of ternary compounds such as ammonium phosphomolybdate, 8-hydroxyquinolinium phosphomolybdate, tetraphenylarsonium phosphomolybdate and tri-n-octylamine phosphomolybdate. Consequently, phosphorus was extracted substoichiometrically by the addition of a substoichiometric amount of molybdenum for the four phosphomolybdate compounds. On the other hand, phosphorus could be separated substoichiometrically with a substoichiometric amount of tetraphenylarsonium chloride or tri-n-octylamine. Stoichiometric ratios of these ternary compounds obtained substoichiometrically were 1:12:3 for phosphorus, molybdenum and organic reagent. The applicability of these compounds to phosphorus determination is also discussed. (author)

  5. Solar unit

    Energy Technology Data Exchange (ETDEWEB)

    Sukhanov, A M; Trushevskiy, S N; Tveryanovich, E V

    1982-01-01

    A solar unit is proposed which contains an inclined solar collector with supply and outlet pipelines, the first of which is connected to the source of a heat carrier, while the second is connected through the valve to the tank for collecting heated heat carrier equipped with a device for recovery. In order to improve the effectiveness of heating the heat carrier, it additionally contains a concentrator of solar radiation and a device for maintaining a level of the heat carrier in the collector in the zone of the focal spot of the concentrator, while the heat pipeline is connected to the source of the heat carrier with the help of a device for maintaining the level of the heat carrier.

  6. Hydroalcohol Fruit Peel Extract

    African Journals Online (AJOL)

    L) fruit peel using 80 % ethanol-induced gastric ulcer model in rats. Methods: Male ... Conclusion: The study shows indicates the antiulcer properties of the methanol extracts of north white ... experimentation, Cimetidine was obtained from.

  7. CARICA PAPAYA EXTRACTS

    African Journals Online (AJOL)

    DR. AMINU

    2Department of Science Laboratory Technology, Hussaini Adamu Federal Polytechnic, Kazaure ... Powdered leaves of Carica papaya (L.) were extracted with ethanol and partitioned in .... about 15 minutes indicated the presence of saponins.

  8. Comparison of mentha extracts obtained by different extraction methods

    Directory of Open Access Journals (Sweden)

    Milić Slavica

    2006-01-01

    Full Text Available The different methods of mentha extraction, such as steam distillation, extraction by methylene chloride (Soxhlet extraction and supercritical fluid extraction (SFE by carbon dioxide (CO J were investigated. SFE by CO, was performed at pressure of 100 bar and temperature of40°C. The extraction yield, as well as qualitative and quantitative composition of obtained extracts, determined by GC-MS method, were compared.

  9. Gold mineralogy and extraction

    Energy Technology Data Exchange (ETDEWEB)

    Cashion, J.D.; Brown, L.J. [Monash University, Physics Department (Australia)

    1998-12-15

    Several examples are examined in which Moessbauer spectroscopic analysis of gold mineral samples, treated concentrates and extracted species has provided information not obtainable by competing techniques. Descriptions are given of current work on bacterial oxidation of pyritic ores and on the adsorbed species from gold extracted from cyanide and chloride solutions onto activated carbon and polyurethane foams. The potential benefits for the gold mining industry from Moessbauer studies and some limitations on the use of the technique are also discussed.

  10. Gold mineralogy and extraction

    International Nuclear Information System (INIS)

    Cashion, J.D.; Brown, L.J.

    1998-01-01

    Several examples are examined in which Moessbauer spectroscopic analysis of gold mineral samples, treated concentrates and extracted species has provided information not obtainable by competing techniques. Descriptions are given of current work on bacterial oxidation of pyritic ores and on the adsorbed species from gold extracted from cyanide and chloride solutions onto activated carbon and polyurethane foams. The potential benefits for the gold mining industry from Moessbauer studies and some limitations on the use of the technique are also discussed

  11. Beam Extraction and Transport

    CERN Document Server

    Kalvas, T.

    2013-12-16

    This chapter gives an introduction to low-energy beam transport systems, and discusses the typically used magnetostatic elements (solenoid, dipoles and quadrupoles) and electrostatic elements (einzel lens, dipoles and quadrupoles). The ion beam emittance, beam space-charge effects and the physics of ion source extraction are introduced. Typical computer codes for analysing and designing ion optical systems are mentioned, and the trajectory tracking method most often used for extraction simulations is described in more detail.

  12. 77 FR 40893 - U.S. Extractive Industries Transparency Initiative Final Stakeholder Assessment and Multi...

    Science.gov (United States)

    2012-07-11

    ... DEPARTMENT OF THE INTERIOR [Docket No. ONRR-2012-0003] U.S. Extractive Industries Transparency... of the U.S. Extractive Industries Transparency Initiative (USEITI) implementation process. On July 11... United States' commitment to participate in the Extractive Industries Transparency Initiative. EITI is a...

  13. Termination unit

    Science.gov (United States)

    Traeholt, Chresten [Frederiksberg, DK; Willen, Dag [Klagshamn, SE; Roden, Mark [Newnan, GA; Tolbert, Jerry C [Carrollton, GA; Lindsay, David [Carrollton, GA; Fisher, Paul W [Heiskell, TN; Nielsen, Carsten Thidemann [Jaegerspris, DK

    2014-01-07

    This invention relates to a termination unit comprising an end-section of a cable. The end section of the cable defines a central longitudinal axis and comprising end-parts of N electrical phases, an end-part of a neutral conductor and a surrounding thermally insulation envelope adapted to comprising a cooling fluid. The end-parts of the N electrical phases and the end-part of the neutral conductor each comprising at least one electrical conductor and being arranged in the cable concentrically around a core former with a phase 1 located relatively innermost, and phase N relatively outermost in the cable, phase N being surrounded by the neutral conductor, electrical insulation being arrange between neighboring electrical phases and between phase N and the neutral conductor, and wherein the end-parts of the neutral conductor and the electrical phases each comprise a contacting surface electrically connected to at least one branch current lead to provide an electrical connection: The contacting surfaces each having a longitudinal extension, and being located sequentially along the longitudinal extension of the end-section of the cable. The branch current leads being individually insulated from said thermally insulation envelope by individual electrical insulators.

  14. Termination unit

    Energy Technology Data Exchange (ETDEWEB)

    Traeholt, Chresten; Willen, Dag; Roden, Mark; Tolbert, Jerry C.; Lindsay, David; Fisher, Paul W.; Nielsen, Carsten Thidemann

    2016-05-03

    Cable end section comprises end-parts of N electrical phases/neutral, and a thermally-insulation envelope comprising cooling fluid. The end-parts each comprises a conductor and are arranged with phase 1 innermost, N outermost surrounded by the neutral, electrical insulation being between phases and N and neutral. The end-parts comprise contacting surfaces located sequentially along the longitudinal extension of the end-section. A termination unit has an insulating envelope connected to a cryostat, special parts at both ends comprising an adapter piece at the cable interface and a closing end-piece terminating the envelope in the end-section. The special parts houses an inlet and/or outlet for cooling fluid. The space between an inner wall of the envelope and a central opening of the cable is filled with cooling fluid. The special part at the end connecting to the cryostat houses an inlet or outlet, splitting cooling flow into cable annular flow and termination annular flow.

  15. Decommissioning Unit Cost Data

    International Nuclear Information System (INIS)

    Sanford, P. C.; Stevens, J. L.; Brandt, R.

    2002-01-01

    The Rocky Flats Closure Site (Site) is in the process of stabilizing residual nuclear materials, decommissioning nuclear facilities, and remediating environmental media. A number of contaminated facilities have been decommissioned, including one building, Building 779, that contained gloveboxes used for plutonium process development but did little actual plutonium processing. The actual costs incurred to decommission this facility formed much of the basis or standards used to estimate the decommissioning of the remaining plutonium-processing buildings. Recent decommissioning activities in the first actual production facility, Building 771, implemented a number of process and procedural improvements. These include methods for handling plutonium contaminated equipment, including size reduction, decontamination, and waste packaging, as well as management improvements to streamline planning and work control. These improvements resulted in a safer working environment and reduced project cost, as demonstrated in the overall project efficiency. The topic of this paper is the analysis of how this improved efficiency is reflected in recent unit costs for activities specific to the decommissioning of plutonium facilities. This analysis will allow the Site to quantify the impacts on future Rocky Flats decommissioning activities, and to develop data for planning and cost estimating the decommissioning of future facilities. The paper discusses the methods used to collect and arrange the project data from the individual work areas within Building 771. Regression and data correlation techniques were used to quantify values for different types of decommissioning activities. The discussion includes the approach to identify and allocate overall project support, waste management, and Site support costs based on the overall Site and project costs to provide a ''burdened'' unit cost. The paper ultimately provides a unit cost basis that can be used to support cost estimates for

  16. Tevatron extraction microcomputer

    International Nuclear Information System (INIS)

    Chapman, L.; Finley, D.A.; Harrison, M.; Merz, W.; Batavia, IL)

    1985-01-01

    Extraction in the Fermilab Tevatron is controlled by a multi-processor Multibus microcomputer system called QXR (Quad eXtraction Regulator). QXR monitors several analog beam signals and controls three sets of power supplies: the ''bucker'' and ''pulse'' magnets at a rate of 5760 Hz, and the ''QXR'' magnets at 720 Hz. QXR supports multiple slow spills (up to a total of 35 seconds) with multiple fast pulses intermixed. It linearizes the slow spill and bucks out the high frequency components. Fast extraction is done by outputting a variable pulse waveform. Closed loop learning techniques are used to improve performance from cycle to cycle for both slow and fast extraction. The system is connected to the Tevatron clock system so that it can track the machine cycle. QXR is also connected to the rest of the Fermilab control system, ACNET. Through ACNET, human operators and central computers can monitor and control extraction through communications with QXR. The controls hardware and software both employ some standard and some specialized components. This paper gives an overview of QXR as a control system; another paper (1) summarizes performance

  17. Tevatron extraction microcomputer

    International Nuclear Information System (INIS)

    Chapman, L.; Finley, D.A.; Harrison, M.; Merz, W.

    1985-06-01

    Extraction in the Fermilab Tevatron is controlled by a multi-processor Multibus microcomputer system called QXR (Quad eXtraction Regulator). QXR monitors several analog beam signals and controls three sets of power supplies: the ''bucker'' and ''pulse'' magnets at a rate of 5760 Hz, and the ''QXR'' magnets at 720 Hz. QXR supports multiple slow spills (up to a total of 35 seconds) with multiple fast pulses intermixed. It linearizes the slow spill and bucks out the high frequency components. Fast extraction is done by outputting a variable pulse waveform. Closed loop learning techniques are used to improve performance from cycle to cycle for both slow and fast extraction. The system is connected to the Tevatron clock system so that it can track the machine cycle. QXR is also connected to the rest of the Fermilab control system, ACNET. Through ACNET, human operators and central computers can monitor and control extraction through communications with QXR. The controls hardware and software both employ some standard and some specialized components. This paper gives an overview of QXR as a control system; another paper summarizes performance

  18. Isoflavones hydrolisis and extraction

    Directory of Open Access Journals (Sweden)

    Jozilene Fernandes Farias dos Santos

    2012-12-01

    Full Text Available Isoflavones are found in leguminous species and are used as phytoestrogens widely used by industry for its beneficial effects as estrogens mimicked, antioxidant action and anti-cancer activity. The identification and quantification of isoflavones in plants is a need due to the high demand of industry. Several methods are used for its extraction, using organic solvents (methanol, ethanol and acetonitrile. Samples from five legumes species from Instituto de Zootecnia (IZ, Forage Gene Bank were tested. All seeds received a hydrothermic treatment immersed in pure water at 50°C for 12 hours. Seeds were then oven-dryed. In this work we tested the extraction using only the hydrothermic treatment and hyfrothermic treatment allied to methanol extaction protocol. Seeds were grinded and half of the samples were ressuspended in PBS (phosphate Buffer and the other half were submited to 4 mL of methanol and 1% of acetic acid, soaked for 5 hours, shaked every 15 minutes, at room temperature. The five legume species that we quantify isoflavones by enzyme immunoassay (EIA were: Calopogonium mucunoides, Bauhinia sp., Cajanus cajan, Galactia martii, Leucaena leucocephala. The extraction procedure is a recomendation of AOAC (Association of Official Analytical Chemists for isoflavone quantification. Ours results show an increase of extraction using methanol 80% plus acetic acid 1% and was obtained using solvent extraction in comparison to hydrothermic procedure alone (figure 1.

  19. Ultrasound-Assisted Extraction: Effect of Extraction Time and Solvent ...

    African Journals Online (AJOL)

    Purpose: To investigate the influence of extraction conditions assisted by ultrasound on the quality of extracts obtained from Mesembryanthemum edule shoots. Methods: The extraction procedure was carried out in an ultrasonic bath. The effect of two solvents (methanol and ethanol) and two extraction times (5 and 10 min) ...

  20. Substoichiometric extraction of chromium

    International Nuclear Information System (INIS)

    Shigematsu, T.; Kudo, K.

    1980-01-01

    Substoichiometric extraction of chromium with tetraphenylarsonium chloride (TPACl), tri-n-octylamine (TNOA), diethylammonium diethyldithiocarbamate (DDDC) and ammonium pyrrolidinedithiocarbamate (APDC) was examined in detail. Chromium can be extracted substoichiometrically in a pH range, which is 1.1-2.6 for the TPACl compound, 0.6-2.3 for the TNOA compound, 5.1-6.4 for the DDDC chelate and 3.9-4.9 for the APDC chelate. Chromium in high-purity calcium carbonate, Orchard Leaves (NBS SRM-1571) and Brewers Yeast (NBS SRM-1569) was determined by neutron activation analysis combined with substoichiometric extraction by DDDC and APDC. The values of 2.0+-0.02 ppm and 2.6+-0.2 ppm were obtained for Brewers Yeast and Orchard Leaves, respectively. These values were in good agreement with those reported by NBS. The reaction mechanism and the reaction ratio between hexavalent chromium and dithiocarbamate are also discussed. (author)

  1. Using GC-FID to Quantify the Removal of 4-sec-Butylphenol from NGS Solvent by NaOH

    Energy Technology Data Exchange (ETDEWEB)

    Sloop, Jr., Frederick V. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moyer, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-12-01

    A caustic wash of the solvent used in the Next-Generation Caustic-Side Solvent Extraction (NG-CSSX) process was found to remove the modifier breakdown product 4-sec-butylphenol (SBP) with varying efficiency depending on the aqueous NaOH concentration. Recent efforts at ORNL have aimed at characterizing the flowsheet chemistry and reducing the technical uncertainties of the NG-CSSX process. One technical uncertainty has been the efficacy of caustic washing of the solvent for the removal of lipophilic anions, in particular, the efficient removal of SBP, an important degradation product of the solvent modifier, Cs-7SB. In order to make this determination, it was necessary to develop a sensitive and reliable analytical technique for the detection and quantitation of SBP. This report recounts the development of a GC-FID-based (Gas Chromatography Flame Ionization Detection) technique for analyzing SBP and the utilization of the technique to subsequently confirm the ability of the caustic wash to efficiently remove SBP from the Next Generation Solvent (NGS) used in NG-CSSX. In particular, the developed technique was used to monitor the amount of SBP removed from a simple solvent and the full NGS by contact with sodium hydroxide wash solutions over a range of concentrations. The results show that caustic washing removes SBP with effectively the same efficiency as it did in the original Caustic-Side Solvent Extraction (CSSX) process.

  2. Genotoxicity of plant extracts

    Directory of Open Access Journals (Sweden)

    Vera M. F. Vargas

    1991-01-01

    Full Text Available Aqueous extracts of seven species used in Brazilian popular medicine (Achyrocline satureoides, Iodina rhombifolia, Desmodium incanum, Baccharis anomala, Tibouchina asperior, Luehea divaricata, Maytenus ilicifolia were screened to the presence of mutagenic activity in the Ames test (Salmonella/microsome. Positive results were obtained for A. satureoides, B anomala and L. divaricata with microsomal activation. As shown elsewhere (Vargas et al., 1990 the metabolites of A. satureoides extract also show the capacity to induce prophage and/or SOS response in microscreen phage induction assay and SOS spot chromotest.

  3. Nano-electromembrane extraction

    DEFF Research Database (Denmark)

    Payán, María D Ramos; Li, Bin; Petersen, Nickolaj J.

    2013-01-01

    as extraction selectivity. Compared with conventional EME, the acceptor phase volume in nano-EME was down-scaled by a factor of more than 1000. This resulted in a very high enrichment capacity. With loperamide as an example, an enrichment factor exceeding 500 was obtained in only 5 min of extraction...... electrophoresis (CE). In that way the sample preparation performed by nano-EME was coupled directly with a CE separation. Separation performance of 42,000-193,000 theoretical plates could easily be obtained by this direct sample preparation and injection technique that both provided enrichment as well...

  4. Uranium extraction at Rossing

    International Nuclear Information System (INIS)

    Kesler, S.B.; Fahrbach, D.O.E.

    1982-01-01

    Rossing Uranium Ltd. operates a large open pit uranium mine and extraction plant at a remote site in the Namib desert. Production started at the plant in 1978. A ferric leach process was introduced later, and the new leach plant began commissioning in October 1981. The process has proved to be reliable and easily controlled. Ferric iron is supplied through recovery from the acid plant calcine, and levels can be maintained above the design levels. Leach extractions were increased more than expected when this process was adopted, and the throughput has been considerably reduced, allowing cost savings in mining and milling

  5. Extraction Methods, Variability Encountered in

    NARCIS (Netherlands)

    Bodelier, P.L.E.; Nelson, K.E.

    2014-01-01

    Synonyms Bias in DNA extractions methods; Variation in DNA extraction methods Definition The variability in extraction methods is defined as differences in quality and quantity of DNA observed using various extraction protocols, leading to differences in outcome of microbial community composition

  6. Grape Seed Extract

    Science.gov (United States)

    ... Greece people have used grapes, grape leaves, and sap for health purposes. Grape seed extract was developed ... sharing research results, and educating the public. Its resources include publications (such as Dietary ... Department of Health & Human Services, National Institutes of Health, National Center for ...

  7. SPS slow extraction septa

    CERN Multimedia

    CERN PhotoLab

    1979-01-01

    SPS long straight section (LSS) with a series of 5 septum tanks for slow extraction (view in the direction of the proton beam). There are 2 of these: in LSS2, towards the N-Area; in LSS6 towards the W-Area. See also Annual Report 1975, p.175.

  8. SPS extraction systems

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    One of the 3-m long electrostatics septa. The septum itself consists of 0.15 mm thick molybdenum wires with a 1.5 mm pitch. Each of the two SPS extraction systems will contain four of these electrostatic septa.

  9. LEAR: antiproton extraction lines

    CERN Multimedia

    Photographic Service

    1992-01-01

    Antiprotons, decelerated in LEAR to a momentum of 100 MeV/c (kinetic energy of 5.3 MeV), were delivered to the experiments in an "Ultra-Slow Extraction", dispensing some 1E9 antiprotons over times counted in hours. Beam-splitters and a multitude of beam-lines allowed several users to be supplied simultaneously.

  10. Concepts for immobilized extractants

    International Nuclear Information System (INIS)

    Paine, R.T.

    1993-01-01

    This paper addresses the problem of cleaning actinides from geomedia. In the past actinides were often released to the ground because of their tendency to bind tightly to forms of geomedia, and in addition spills have occurred over time. To remediate these areas involves finding ways to either guarantee the retention of the actinides in the geomedia, or finding ways to extract them and leave the soils clean. One possible way to clean soils is to wash them, which in order to extract actinides means the use of ligands which bind competitively with actinides in the presence of soil fractions. An array of organic ligands is known which bind with actinides, but the larger problem of handling these ligands in a manner which allows concentration of the actinides is still open. The author addresses work to bind such ligands to different types of matrices which can then be used in packed extraction columns to remove actindes from flow streams, and finally concentrated, by using minimal volume backflushing to extract the actinides from the column

  11. Uranium extraction from phosphoric acid

    International Nuclear Information System (INIS)

    Araujo Figueiredo, C. de

    1984-01-01

    The recovery of uranium from phosphoric liquor by two extraction process is studied. First, uranium is reduced to tetravalent condition and is extracted by dioctypyrophosphoric acid. The re-extraction is made by concentrated phosphoric acid with an oxidizing agent. The re-extract is submitted to the second process and uranium is extracted by di-ethylhexilphosphoric acid and trioctylphosphine oxide. (M.A.C.) [pt

  12. Fracking in the United States

    International Nuclear Information System (INIS)

    Cho, Renee

    2015-01-01

    Over the last decade, advances in technology have made it profitable to extract natural gas from shale, leading to a boom in shale gas development in the United States. Hydraulic fracturing, or fracking, the controversial method for extracting natural gas, offers numerous benefits: relatively cheap energy, enhanced energy security, job creation, tax revenues and decreased dependence on dirty coal. Fracking, however, can also increase greenhouse gas emissions, pollute the air and result in health effects, consume huge quantities of water, and cause earthquakes. While some areas welcome fracking for the economic benefits it brings, other communities are attempting to ban fracking altogether. This article examines the benefits and risks of fracking in the U.S

  13. Refining of yellow cake by solvent extraction. Pakistan status report

    International Nuclear Information System (INIS)

    Yunus, M.; Muzaffar, A.; Qureshi, M.T.; Qazi, N.K.; Khan, J.R.; Chughtai, N.A.; Zaidi, S.M.H.

    1980-01-01

    The paper describes the pilot-plant studies made at the Pakistan Institute of Nuclear Science and Technology, Rawalpindi, on refining yellow cake. The process units mainly consist of digestion and filtration, solvent extraction, precipitation and filtration, and calcining and reduction. Extraction parameters, such as free acidity in terms of nitrate ion concentration, throughputs and AF index, have been studied in some detail. Product of satisfactory chemical purity, as confirmed by spectrochemical analysis, was produced by this method. (author)

  14. United Nations Environment Programme. Annual Review 1981.

    Science.gov (United States)

    United Nations Environment Programme, Nairobi (Kenya).

    This edition of the United Nations Environment Programme (UNEP) annual report is structured in three parts. Part 1 focuses on three contemporary problems (ground water, toxic chemicals and human food chains and environmental economics) and attempts to solve them. Also included is a modified extract of "The Annual State of the Environment…

  15. Experimental Investigation of Double Effect Evaporative Cooling Unit

    Directory of Open Access Journals (Sweden)

    Ahmed Abd Mohammad Saleh

    2018-03-01

    Full Text Available This work presents the experimental investigation of double effect evaporative cooling unit with approximate capacity 7 kW. The unit consisted of two stages, the sensible heat exchanger and the cooling tower composing the external indirect regenerative evaporative cooling stage where a direct evaporative cooler represent the second stage. Testing results showed a maximum capacity and lowest supplied air temperature when the water flow rate in heat exchanger was 0.1 L/s. The experiment recorded the unit daily readings at two airflow rates (0.425 m3/s, 0.48 m3/s. The reading shows that unit inlet DBT is effect positively on unit wet bulb effectiveness and unit COP at constant humidity ratio. The air extraction ratio effected positively on the unit wet bulb effectiveness within a certain limit where maximum COP recorded 11.4 when the extraction ratio equal to 40%.

  16. Economic and process optimization of ethanol production by extractive fermentation

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    This report demonstrates by computer simulation the economic advantages of extractive fermentation on an industrial scale compared to the best alternative technology currently available. The simulations were based on a plant capacity of 100 x 10 6 L/y of azeotropic ethanol. The simulation results were verified with a fully integrated, computer controlled extractive fermentation process demonstration unit based around a 7 L fermentor operated with a synthetic glucose medium and using Saccharomyces cerevisiae. The system was also operated with natural substrates (blackstrap molasses and grain hydrolyzate). Preliminary tests with the organism Zymomonas mobilis were also carried out under extractive fermentation conditions.

  17. Centrifugal contractors for laboratory-scale solvent extraction tests

    International Nuclear Information System (INIS)

    Leonard, R.A.; Chamberlain, D.B.; Conner, C.

    1995-01-01

    A 2-cm contactor (minicontactor) was developed and used at Argonne National Laboratory for laboratory-scale testing of solvent extraction flowsheets. This new contactor requires only 1 L of simulated waste feed, which is significantly less than the 10 L required for the 4-cm unit that had previously been used. In addition, the volume requirements for the other aqueous and organic feeds are reduced correspondingly. This paper (1) discusses the design of the minicontactor, (2) describes results from having applied the minicontactor to testing various solvent extraction flowsheets, and (3) compares the minicontactor with the 4-cm contactor as a device for testing solvent extraction flowsheets on a laboratory scale

  18. Automated Water Extraction Index

    DEFF Research Database (Denmark)

    Feyisa, Gudina Legese; Meilby, Henrik; Fensholt, Rasmus

    2014-01-01

    Classifying surface cover types and analyzing changes are among the most common applications of remote sensing. One of the most basic classification tasks is to distinguish water bodies from dry land surfaces. Landsat imagery is among the most widely used sources of data in remote sensing of water...... resources; and although several techniques of surface water extraction using Landsat data are described in the literature, their application is constrained by low accuracy in various situations. Besides, with the use of techniques such as single band thresholding and two-band indices, identifying...... an appropriate threshold yielding the highest possible accuracy is a challenging and time consuming task, as threshold values vary with location and time of image acquisition. The purpose of this study was therefore to devise an index that consistently improves water extraction accuracy in the presence...

  19. Extractable Work from Correlations

    Directory of Open Access Journals (Sweden)

    Martí Perarnau-Llobet

    2015-10-01

    Full Text Available Work and quantum correlations are two fundamental resources in thermodynamics and quantum information theory. In this work, we study how to use correlations among quantum systems to optimally store work. We analyze this question for isolated quantum ensembles, where the work can be naturally divided into two contributions: a local contribution from each system and a global contribution originating from correlations among systems. We focus on the latter and consider quantum systems that are locally thermal, thus from which any extractable work can only come from correlations. We compute the maximum extractable work for general entangled states, separable states, and states with fixed entropy. Our results show that while entanglement gives an advantage for small quantum ensembles, this gain vanishes for a large number of systems.

  20. Apparatus for extracting petroleum

    Energy Technology Data Exchange (ETDEWEB)

    Coogan, J

    1921-01-18

    An apparatus for extracting petroleum from petroleum bearing sand or shale is described comprising a container for liquids, the container being divided into a plurality of compartments, an agitator mounted within the container and below the liquid level and having its forward end opening into one of the compartments, means for delivering sand or shale to the forward end of the agitator, means for subjecting the sand or shale to the action of a solvent for the petroleum while the sand or shale is being agitated and is submerged, the first-mentioned compartment being adapted to receive the extracted petroleum and means for removing the treated sand or shale from adjacent the rear end of the agitator.

  1. HOUSING UNITS Units in Structure for Occupied Units NMSD 2000

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — The 2006 Second Edition TIGER/Line files are an extract of selected geographic and cartographic information from the Census TIGER database. The geographic coverage...

  2. HOUSING UNITS Units in Structure for Occupied Units NMHD 2000

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — The 2006 Second Edition TIGER/Line files are an extract of selected geographic and cartographic information from the Census TIGER database. The geographic coverage...

  3. Solid phase extraction membrane

    Science.gov (United States)

    Carlson, Kurt C [Nashville, TN; Langer, Roger L [Hudson, WI

    2002-11-05

    A wet-laid, porous solid phase extraction sheet material that contains both active particles and binder and that possesses excellent wet strength is described. The binder is present in a relatively small amount while the particles are present in a relatively large amount. The sheet material is sufficiently strong and flexible so as to be pleatable so that, for example, it can be used in a cartridge device.

  4. Gold and uranium extraction

    International Nuclear Information System (INIS)

    James, G.S.; Davidson, R.J.

    1977-01-01

    A process for extracting gold and uranium from an ore containing them both comprising the steps of pulping the finely comminuted ore with a suitable cyanide solution at an alkaline pH, acidifying the pulp for uranium dissolution, adding carbon activated for gold recovery to the pulp at a suitable stage, separating the loaded activated carbon from the pulp, and recovering gold from the activated carbon and uranium from solution

  5. Extractive metallurgy. Recent advances

    International Nuclear Information System (INIS)

    Stevenson, E.J.

    1977-01-01

    Detailed technical information derived from patents issued since 1975 on extractive metallurgy is presented. In part one, concerning copper, the major areas covered are: smelting and roasting; acid leaching; ammonia leach processes; cuprous chloride and ferric chloride; and recovery of copper values from solution. Part two covers other metals, including: nickel and cobalt; ocean floor nodules; lead, zinc, molybdenum and manganese; precious metals; and uranium titanium, tantalum, rhenium, gallium, and other metals

  6. Solvent extraction columns

    International Nuclear Information System (INIS)

    Middleton, P.; Smith, J.R.

    1979-01-01

    In pulsed columns for use in solvent extraction processes, e.g. the reprocessing of nuclear fuel, the horizontal perforated plates inside the column are separated by interplate spacers manufactured from metallic neutron absorbing material. The spacer may be in the form of a spiral or concentric circles separated by radial limbs, or may be of egg-box construction. Suitable neutron absorbing materials include stainless steel containing boron or gadolinium, hafnium metal or alloys of hafnium. (UK)

  7. Influence of Extraction Parameters on Hydroalcohol Extracts of the ...

    African Journals Online (AJOL)

    The parameter that had the greatest influence on extraction process was alcohol concentration ... rules and processing steps [2]. As part .... Table 1: Extractive batch nnumbers with the respective factors and levels studied in the factorial design.

  8. Plant extracts as radioprotectors

    Energy Technology Data Exchange (ETDEWEB)

    Baydoun, S; Al-Oudat, M [Atomic Energy Commission, Department of Radiation Protection and Nuclear Safety, Damascus (Syrian Arab Republic); Al-Achkar, W [Atomic Energy Commission, Department of Radiobiology and Health, Damascus (Syrian Arab Republic)

    1996-09-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author) 16 refs., 2 tabs., 4 figs.

  9. Plant extracts as radioprotectors

    International Nuclear Information System (INIS)

    Baydoun, S.; Al-Oudat, M.; Al-Achkar, W.

    1996-09-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author) 16 refs., 2 tabs., 4 figs

  10. Plant extracts as radioprotectors

    International Nuclear Information System (INIS)

    Baydoun, S.; Al-Oudat, M.; Al-Achkar, W.

    1997-01-01

    Several studies show that the extracts of some plants, namely containing vitamins or sulfide components, have radioprotection properties against the effects of ionizing radiation. In Syria, many of hates plants are available. This experiment was conducted in order to test the ability of ten different plants to protect against the radiation damages. These plants are Daucus carota L., Brassica oleracea L, Aloe vera L., Opuntia ficus-indica, Allium cepa L., Capsicum annuum L., Scilla maritima L., Allium sativum L., Rubus sanctus L. and Rosa canina L.Their effects on the protection of E. Coli growth after the exposure to L.D 50 of gamma radiation (100 Gy) were investigated . Two concentrations to each plant extract were tested, both were than 1%. Our results are indicating that the protection depend on plant. The radioprotection factors were ranged between 1.42 to 2.39. The best results were obtained by using the extract of Allium sativum L. (2.01), Opuntia ficus-indica (2.14) and Capsiucum annuum L. (2.39). (author)

  11. Solvent extraction of zirconium

    International Nuclear Information System (INIS)

    Kim, S.S.; Yoon, J.H.

    1981-01-01

    The extraction of zirconium(VI) from an aqueous solution of constant ionic strength with versatic acid-10 dissolved in benzen was studied as a function of pH and the concentration of zirconium(VI) and organic acid. The effects of sulphate and chlorine ions on the extraction of the zirconium(VI) were briefly examined. It was revealed that (ZrOR 2 .2RH) is the predominant species of extracted zirconium(VI) in the versatic acid-10. The chemical equation and the apparent equilibrium constants thereof have been determined as follows. (ZrOsup(2+))aq+ 2(R 2 H 2 )sub(org) = (ZrOR 2 .2RH)sub(org)+2(H + )aq Ksub(Zr) = (ZrOR 2 .2RH)sub(org)(H + ) 2 /(ZrOsup(2+))sub(aq)(R 2 H 2 )sup(2)sub(org) = 3.3 x 10 -7 . The synergistic effects of TBP and D2EHPA were also studied. In the mixed solvent with 0.1M TBP, the synergistic effect was observed, while the mixed solvent with D2EHPA showed the antisynergistic effect. (Author)

  12. Hanford Site Waste Managements Units reports

    International Nuclear Information System (INIS)

    1992-01-01

    The Hanford Site Waste Management Units Report (HSWMUR) was originated to provide information responsive to Section 3004(u) of the Hazardous and Solid Waste Amendments (HSWA) of the 1984 United States Code (USC 1984). This report provides a comprehensive inventory of all types of waste management units at the Hanford Site, including a description of the units and the waste they contain. Waste management units in this report include: (1) Resource Conservation and Recovery Act of 1976 (RCRA) disposal units, (2) Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) disposal units, (3) unplanned releases, (4) inactive contaminated structures, (5) RCRA treatment, storage, and disposal (TSD) units, and (6) other storage areas. Because of the comprehensive nature of this report, the listing of sites is more extensive than required by Section 3004(u) of HSWA. The information in this report is extracted from the Waste Information Data System (WIDS). The WIDS provides additional information concerning the waste management units contained in this report and is maintained current with changes to these units. This report is updated annually if determined necessary per the Hanford Federal Facility Agreement and Consent Order Order (commonly referred to as the Tri-Party Agreement, Ecology et al. 1990). This report identifies 1,414 waste management units. Of these, 1,015 units are identified as solid waste management units (SWMU), and 342 are RCRA treatment, storage, and disposal units. The remaining 399 are comprised mainly of one-time spills to the environment, sanitary waste disposal facilities (i.e., septic tanks), and surplus facilities awaiting decontamination and decommissioning

  13. EXTRACTION OF MONOAZO DYES BY HYDROPHILIC EXTRACTANTS FROM AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    Y. I. Korenman

    2012-01-01

    Full Text Available The extraction of mono azo dyes E102, E122, E110, E124, E129 from aqueous solutions with hydrophilic solvents (alcohols, esters, ketones and polymers (poly-N-vinylamides, polyethylene glycol was studied. The main regularities of extraction are established. The distribution coefficients and degree of extraction of dyes was estimate. The influence of the nature of solvents and polymers on the extraction of dyes from aqueous solutions are established.

  14. Understanding extractive bleed : wood extractives: distribution, properties, and classes

    Science.gov (United States)

    Edward Burke; Norm Slavik; Tony Bonura; Dennis Connelly; Tom Faris; Arnie Nebelsick; Brent Stuart; Sam Williams; Alex C. Wiedenhoeft

    2010-01-01

    Color, odor, and natural durability of heartwood are characteristics imparted by a class of chemicals in wood known collectively extractives. Wood is converted by the tree from sapwood to heartwood by the deposition of extractives, typically many years after the growth ring undergoing this change was formed by the tree. Extractives are thus not a part of the wood...

  15. ACTIVITIES OF ACACIA NILOTICA EXTRACTS

    African Journals Online (AJOL)

    DR. AMINU

    sensitivity tests of crude extract fractions of the plant extracts using ethanol, chloroform, methanol, petroleum ether, water and ethyl acetate were investigated on nine bacterial isolates. .... These were obtained by punching the filter paper with.

  16. Dynamics of Agricultural Groundwater Extraction

    NARCIS (Netherlands)

    Hellegers, P.J.G.J.; Zilberman, D.; Ierland, van E.C.

    2001-01-01

    Agricultural shallow groundwater extraction can result in desiccation of neighbouring nature reserves and degradation of groundwater quality in the Netherlands, whereas both externalities are often not considered when agricultural groundwater extraction patterns are being determined. A model is

  17. Improvements in solvent extraction columns

    International Nuclear Information System (INIS)

    Aughwane, K.R.

    1987-01-01

    Solvent extraction columns are used in the reprocessing of irradiated nuclear fuel. For an effective reprocessing operation a solvent extraction column is required which is capable of distributing the feed over most of the column. The patent describes improvements in solvent extractions columns which allows the feed to be distributed over an increased length of column than was previously possible. (U.K.)

  18. AGRICULTURAL USES OF SEAWEEDS EXTRACTS

    Directory of Open Access Journals (Sweden)

    Monica Popescu

    2013-12-01

    Full Text Available Marine bioactive substances extracted from seaweed are currently used in food, animal feed, as a raw material in the industry and have therapeutic applications. Most of the products based on marine algae are extracted from Brown algae Ascophyllum nodosum. The use of extracts of seaweed in agriculture is beneficial because the amount of chemical fertilizers and obtaining organic yield.

  19. On extraction reagents for hydrometallurgy

    International Nuclear Information System (INIS)

    Zolotov, Yu.A.

    1975-01-01

    Fundamental requirements to the extractants are considered. Ways of obtaining selective extractants are discussed in particular on the basis of coordination chemistry achivements. Attention is drawn to expediency of study (as extractants) of flotation reagents, additions to the oil, pesticides, accelerators of caoutchouc vulcanization

  20. Challenges in Managing Information Extraction

    Science.gov (United States)

    Shen, Warren H.

    2009-01-01

    This dissertation studies information extraction (IE), the problem of extracting structured information from unstructured data. Example IE tasks include extracting person names from news articles, product information from e-commerce Web pages, street addresses from emails, and names of emerging music bands from blogs. IE is all increasingly…

  1. Extracting Tag Hierarchies

    Science.gov (United States)

    Tibély, Gergely; Pollner, Péter; Vicsek, Tamás; Palla, Gergely

    2013-01-01

    Tagging items with descriptive annotations or keywords is a very natural way to compress and highlight information about the properties of the given entity. Over the years several methods have been proposed for extracting a hierarchy between the tags for systems with a "flat", egalitarian organization of the tags, which is very common when the tags correspond to free words given by numerous independent people. Here we present a complete framework for automated tag hierarchy extraction based on tag occurrence statistics. Along with proposing new algorithms, we are also introducing different quality measures enabling the detailed comparison of competing approaches from different aspects. Furthermore, we set up a synthetic, computer generated benchmark providing a versatile tool for testing, with a couple of tunable parameters capable of generating a wide range of test beds. Beside the computer generated input we also use real data in our studies, including a biological example with a pre-defined hierarchy between the tags. The encouraging similarity between the pre-defined and reconstructed hierarchy, as well as the seemingly meaningful hierarchies obtained for other real systems indicate that tag hierarchy extraction is a very promising direction for further research with a great potential for practical applications. Tags have become very prevalent nowadays in various online platforms ranging from blogs through scientific publications to protein databases. Furthermore, tagging systems dedicated for voluntary tagging of photos, films, books, etc. with free words are also becoming popular. The emerging large collections of tags associated with different objects are often referred to as folksonomies, highlighting their collaborative origin and the “flat” organization of the tags opposed to traditional hierarchical categorization. Adding a tag hierarchy corresponding to a given folksonomy can very effectively help narrowing or broadening the scope of search

  2. Extracting tag hierarchies.

    Directory of Open Access Journals (Sweden)

    Gergely Tibély

    Full Text Available Tagging items with descriptive annotations or keywords is a very natural way to compress and highlight information about the properties of the given entity. Over the years several methods have been proposed for extracting a hierarchy between the tags for systems with a "flat", egalitarian organization of the tags, which is very common when the tags correspond to free words given by numerous independent people. Here we present a complete framework for automated tag hierarchy extraction based on tag occurrence statistics. Along with proposing new algorithms, we are also introducing different quality measures enabling the detailed comparison of competing approaches from different aspects. Furthermore, we set up a synthetic, computer generated benchmark providing a versatile tool for testing, with a couple of tunable parameters capable of generating a wide range of test beds. Beside the computer generated input we also use real data in our studies, including a biological example with a pre-defined hierarchy between the tags. The encouraging similarity between the pre-defined and reconstructed hierarchy, as well as the seemingly meaningful hierarchies obtained for other real systems indicate that tag hierarchy extraction is a very promising direction for further research with a great potential for practical applications. Tags have become very prevalent nowadays in various online platforms ranging from blogs through scientific publications to protein databases. Furthermore, tagging systems dedicated for voluntary tagging of photos, films, books, etc. with free words are also becoming popular. The emerging large collections of tags associated with different objects are often referred to as folksonomies, highlighting their collaborative origin and the "flat" organization of the tags opposed to traditional hierarchical categorization. Adding a tag hierarchy corresponding to a given folksonomy can very effectively help narrowing or broadening the scope of

  3. Extracting tag hierarchies.

    Science.gov (United States)

    Tibély, Gergely; Pollner, Péter; Vicsek, Tamás; Palla, Gergely

    2013-01-01

    Tagging items with descriptive annotations or keywords is a very natural way to compress and highlight information about the properties of the given entity. Over the years several methods have been proposed for extracting a hierarchy between the tags for systems with a "flat", egalitarian organization of the tags, which is very common when the tags correspond to free words given by numerous independent people. Here we present a complete framework for automated tag hierarchy extraction based on tag occurrence statistics. Along with proposing new algorithms, we are also introducing different quality measures enabling the detailed comparison of competing approaches from different aspects. Furthermore, we set up a synthetic, computer generated benchmark providing a versatile tool for testing, with a couple of tunable parameters capable of generating a wide range of test beds. Beside the computer generated input we also use real data in our studies, including a biological example with a pre-defined hierarchy between the tags. The encouraging similarity between the pre-defined and reconstructed hierarchy, as well as the seemingly meaningful hierarchies obtained for other real systems indicate that tag hierarchy extraction is a very promising direction for further research with a great potential for practical applications. Tags have become very prevalent nowadays in various online platforms ranging from blogs through scientific publications to protein databases. Furthermore, tagging systems dedicated for voluntary tagging of photos, films, books, etc. with free words are also becoming popular. The emerging large collections of tags associated with different objects are often referred to as folksonomies, highlighting their collaborative origin and the "flat" organization of the tags opposed to traditional hierarchical categorization. Adding a tag hierarchy corresponding to a given folksonomy can very effectively help narrowing or broadening the scope of search. Moreover

  4. Resinous constituent extracting process

    Energy Technology Data Exchange (ETDEWEB)

    Sayer, W F

    1947-10-07

    The method of recovering oily constituents from coal or oil shale comprising the saturation of coal or oil shale in a sealed vessel with an organic solution having a boiling point at atmospheric pressure of not exceeding 220/sup 0/C, elevating the temperature within the vessel to a temperature below the cracking temperature of the constituents and maintaining the pressure within the vessel below 51 pounds, to extract the oily material from the coal or oil shale and subsequently separating the solvent from the oily material.

  5. Microbiological metal extraction processes

    International Nuclear Information System (INIS)

    Torma, A.E.

    1991-01-01

    Application of biotechnological principles in the mineral processing, especially in hydrometallurgy, has created new opportunities and challenges for these industries. During the 1950's and 60's, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes for copper and uranium. The interest in bio-leaching processes is the consequence of economic advantages associated with these techniques. For example, copper can be produced from mining wastes for about 1/3 to 1/2 of the costs of copper production by the conventional smelting process from high-grade sulfide concentrates. The economic viability of bio leaching technology lead to its world wide acceptance by the extractive industries. During 1970's this technology grew into a more structured discipline called 'bio hydrometallurgy'. Currently, bio leaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, precious metals and for the desulfurization of high-sulfur content pyritic coals. As a developing technology, the microbiological leaching of the less common and rare metals has yet to reach commercial maturity. However, the research in this area is very active. In addition, in a foreseeable future the biotechnological methods may be applied also for the treatment of high-grade ores and mineral concentrates using adapted native and/or genetically engineered microorganisms. (author)

  6. Carcinogenicity of soil extracts

    Energy Technology Data Exchange (ETDEWEB)

    Shcherbak, N P

    1970-01-01

    A total of 270 3-mo-old mice, hybrids of the C57BL and CBA strains which are highly susceptible to carcinogens, were painted on the skin (2-3 admin./week) with 3-4 drops of (1) a concentrated benzene extract of soil taken near a petroleum refinery with a 3,4 benzpyrene (BP) content of 0.22%; (2) a 0.22% soln of pure BP in benzene; (3) a concentrated benzene extract of soil taken from an old residential area of Moscow (BP content 0.0004%); (4) a 0.0004% BP soln in benzene; and (5) pure benzene. Only mice in the first 2 groups developed tumors. In group (1), 8 mice had papillomas, 46 had skin cancer, 1 had a sarcoma and 2 had plasmocytomas. In group (2) all 60 animals had skin cancer. Lung metastases were present at autopsy in 5 mice in group (1) and in 10 mice in group (2); in some cases, these tumors were multiple. Lymph node metastases were found in 6 mice in group (1) and in 10 mice in group (2). Tumors developed more slowly in group (1) than in group (2).

  7. Remaining useful life estimation based on discriminating shapelet extraction

    International Nuclear Information System (INIS)

    Malinowski, Simon; Chebel-Morello, Brigitte; Zerhouni, Noureddine

    2015-01-01

    In the Prognostics and Health Management domain, estimating the remaining useful life (RUL) of critical machinery is a challenging task. Various research topics including data acquisition, fusion, diagnostics and prognostics are involved in this domain. This paper presents an approach, based on shapelet extraction, to estimate the RUL of equipment. This approach extracts, in an offline step, discriminative rul-shapelets from an history of run-to-failure data. These rul-shapelets are patterns that are selected for their correlation with the remaining useful life of the equipment. In other words, every selected rul-shapelet conveys its own information about the RUL of the equipment. In an online step, these rul-shapelets are compared to testing units and the ones that match these units are used to estimate their RULs. Therefore, RUL estimation is based on patterns that have been selected for their high correlation with the RUL. This approach is different from classical similarity-based approaches that attempt to match complete testing units (or only late instants of testing units) with training ones to estimate the RUL. The performance of our approach is evaluated on a case study on the remaining useful life estimation of turbofan engines and performance is compared with other similarity-based approaches. - Highlights: • A data-driven RUL estimation technique based on pattern extraction is proposed. • Patterns are extracted for their correlation with the RUL. • The proposed method shows good performance compared to other techniques

  8. Effect of propolis extract on angelfish larval performance and transport

    Directory of Open Access Journals (Sweden)

    Douglas da Cruz Mattos

    2017-06-01

    Full Text Available This study aimed to evaluate the influence propolis extract inclusion to the feed mixture for juvenile angelfish (Pterophyllum scalare on larval performance and transport. Levels of propolis extract inclusion consisted of 0, 300, 600, 900, and 1200 mg.kg-1 of feed. After 14 days of hatching, unmetamorphosed larvae with a total length of 18.4 mm and 0.11 g initial weight were used. Six-hundred larvae were divided into 20 experimental units, totalizing 30 larvae each. Experimental units consisted of polythene containers with independent water input and output and a level controller. Each unit was controlled for maintenance of 40 L water within a recirculation system. After offering feed containing propolis extract, five fish from each experimental unit were packed in bags for transportation only with atmospheric air, without pure oxygen addition. The bags were filled with 300 mL water on a 2:1 basis of air and water respectively. The total transport time was considered until the death of the third fish in package. At the end of the experiment, data underwent statistical analysis through Statistical Analysis System (SAS, 2001. Results showed there was no significant difference (P < 0.05 neither for any of the studied zootechnical variables (standard length, total length, height, and weight nor for the transport of juveniles. In conclusion, propolis extract addition to angelfish feed was ineffective for larval performance and for transportation of juveniles, at the levels tested here.

  9. 7 CFR 51.1179 - Method of juice extraction.

    Science.gov (United States)

    2010-01-01

    ... STANDARDS) United States Standards for Grades of Florida Oranges and Tangelos Standards for Internal Quality... 7 Agriculture 2 2010-01-01 2010-01-01 false Method of juice extraction. 51.1179 Section 51.1179 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards...

  10. Extraction and determination of organosulfur compounds in water

    African Journals Online (AJOL)

    Preferred Customer

    predominant odorants from bioindustry emissions [5]. ... The International Labor Organization of the United Nations reports that some ... are typically chlorinated solvents such as chlorobenzene, chloroform and carbon tetrachloride, ... one imposes rather stringent restrictions on the choice of the DLLME-SFO extraction ...

  11. 200-BP-5 operable unit treatability test report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    The 200-BP-5 Operable Unit was established in response to recommendations presented in the 200 East Groundwater Aggregate Area Management Study Report (AAMSR) (DOE-RL 1993a). Recognizing different approaches to remediation, the groundwater AAMSR recommended separating groundwater from source and vadose zone operable units and subdividing 200 East Area groundwater into two operable units. The division between the 200-BP-5 and 200-PO-1 Operable Units was based principally on source operable unit boundaries and distribution of groundwater plumes derived from either B Plant or Plutonium/Uranium Extraction (PUREX) Plant liquid waste disposal sites.

  12. 200-BP-5 operable unit treatability test report

    International Nuclear Information System (INIS)

    1996-04-01

    The 200-BP-5 Operable Unit was established in response to recommendations presented in the 200 East Groundwater Aggregate Area Management Study Report (AAMSR) (DOE-RL 1993a). Recognizing different approaches to remediation, the groundwater AAMSR recommended separating groundwater from source and vadose zone operable units and subdividing 200 East Area groundwater into two operable units. The division between the 200-BP-5 and 200-PO-1 Operable Units was based principally on source operable unit boundaries and distribution of groundwater plumes derived from either B Plant or Plutonium/Uranium Extraction (PUREX) Plant liquid waste disposal sites

  13. Counter current extraction for the partitioning of actinides from PFBR-SHLW using TODGA

    International Nuclear Information System (INIS)

    Ansari, S.A.; Gujar, R.B.; Kumar, Mithilesh; Seshagiri, T.K.; Godbole, S.V.; Manchanda, V.K.; Rajeswari, S.; Antony, M.P.; Srinivasan, T.G.

    2009-01-01

    Counter current extraction for the partitioning of actinides from simulated HLW of PFBR origin was demonstrated with 0.1M TODGA + 0.5M DHOA dissolved in NPH using a 16 stage mixer-settler unit. Results demonstrated that all lanthanides could be quantitatively extracted from the feed solution and quantitatively stripped from the loaded organic phase with 0.2M HNO 3 . The extracted lanthanides are not scrubbed with 0.2M oxalic acid at 5M HNO 3 in the scrubbing cycle. Elements such as Ba, Cd and Sn were not extracted. However, Pd was partially extracted but was scrubbed quantitatively. (author)

  14. Supercritical fluid extraction of hops

    Directory of Open Access Journals (Sweden)

    ZORAN ZEKOVIC

    2007-01-01

    Full Text Available Five cultivars of hop were extracted by the method of supercritical fluid extraction using carbon dioxide (SFE–CO2 as extractant. The extraction (50 g of hop sample using a CO2 flow rate of 97.725 L/h was done in the two steps: 1. extraction at 150 bar and 40°C for 2.5 h (sample of series A was obtained and, after that, the same sample of hop was extracted in the second step: 2. extraction at 300 bar and 40 °C for 2.5 h (sample of series B was obtained. The Magnum cultivar was chosen for the investigation of the extraction kinetics. For the qualitative and quantitative analysis of the obtained hop extracts, the GC-MS method was used. Two of four themost common compounds of hop aroma (a-humulene and b-caryophyllene were detected in samples of series A. In addition, isomerized a-acids and a high content of b-acids were detected. The a-acids content in the samples of series B was the highest in the extract of the Magnum cultivar (it is a bitter variety of hop. The low contents of a-acids in all the other hop samples resulted in extracts with low a-acids content, i.e., that contents were under the prescribed a-acids content.

  15. Economic evaluation of in situ extraction for copper, gold, and uranium

    International Nuclear Information System (INIS)

    Lewis, F.M.; Chase, C.K.; Bhappu, R.B.

    1976-01-01

    In situ extraction for copper, gold, and uranium, generally involves several common alternative processes and techniques. These include dump leaching, heap leaching, leaching of fractured ore in-place or bore hole mining and unit operations such as cementation, solvent extraction, ion-exchange, or carbon-in-pulp. Since the metallurgical effectiveness and economics of such processes and unit operations are well established, it would be possible to select the optimum alternative for extracting either copper, gold, or uranium from their ores using in situ extraction technology. Efforts made to provide metallurgical evaluation as well as capital and operating costs for the various processes and unit operations are reported. These costs are used in preparing feasibility studies for in situ extraction of these metals

  16. Oxygen Extraction from Minerals

    Science.gov (United States)

    Muscatello, Tony

    2017-01-01

    Oxygen, whether used as part of rocket bipropellant or for astronaut life support, is a key consumable for space exploration and commercialization. In Situ Resource Utilization (ISRU) has been proposed many times as a method for making space exploration more cost effective and sustainable. On planetary and asteroid surfaces the presence of minerals in the regolith that contain oxygen is very common, making them a potential oxygen resource. The majority of research and development for oxygen extraction from minerals has been for lunar regolith although this work would generally be applicable to regolith at other locations in space. This presentation will briefly survey the major methods investigated for oxygen extraction from regolith with a focus on the current status of those methods and possible future development pathways. The major oxygen production methods are (1) extraction from lunar ilmenite (FeTiO3) with either hydrogen or carbon monoxide, (2) carbothermal reduction of iron oxides and silicates with methane, and (3) molten regolith electrolysis (MRE) of silicates. Methods (1) and (2) have also been investigated in a two-step process using CO reduction and carbon deposition followed by carbothermal reduction. All three processes have byproducts that could also be used as resources. Hydrogen or carbon monoxide reduction produce iron metal in small amounts that could potentially be used as construction material. Carbothermal reduction also makes iron metal along with silicon metal and a glass with possible applications. MRE produces iron, silicon, aluminum, titanium, and glass, with higher silicon yields than carbothermal reduction. On Mars and possibly on some moons and asteroids, water is present in the form of mineral hydrates, hydroxyl (-OH) groups on minerals, andor water adsorbed on mineral surfaces. Heating of the minerals can liberate the water which can be electrolyzed to provide a source of oxygen as well. The chemistry of these processes, some key

  17. SI units in radiology

    Energy Technology Data Exchange (ETDEWEB)

    Iyer, P S [Bhabha Atomic Research Centre, Bombay (India). Div. of Radiation Protection

    1978-11-01

    The proposal of the International Commission on Radiation Units and Measurements that the special units of radiation and radioactivity-roentgen, rad, rem and curie-be replaced by the International System (SI) of Units has been accepted by international bodies. This paper reviews the resons for introducing the new units and their features. The relation between the special units and the corresponding SI units is discussed with examples. In spite of anticipated difficulties, the commission recommends a smooth and efficient changeover to the SI units in ten years.

  18. Lithium extractive metallurgy

    International Nuclear Information System (INIS)

    Josa, J.M.; Merino, J.L.

    1985-01-01

    The Nuclear Fusion National Program depends on lithium supplies. Extractive metallurgy development is subordinate to the localization and evaluation of ore resources. Nowadays lithium raw materials usable with present technology consist of pegmatite ore and brine. The Instituto Geologico y Minero Espanol (IGME) found lepidolite, ambligonite and spodrimene in pegmatite ores in different areas of Spain. However, an evaluation of resources has not been made. Different Spanish surface and underground brines are to be sampled and analyzed. If none of these contain significant levels of lithium, the Junta de Energia Nuclear (JEN) will try an agreement with IGME for ENUSA (Empresa Nacional del Uranio, S.A.) to explore pegmatite-ore bodies from different locations. Different work stages, laboratory tests, pilots plants tests and commercial plant, are foreseen, if the deposits are found. (author)

  19. Influence of Extraction Parameters on Hydroalcohol Extracts of the ...

    African Journals Online (AJOL)

    ... the influence of alcohol concentration (50, 70 and 90 % v/v), extraction time (2, 6 and 10 h), and particle size of the herbal drug (0.25, 0.5 and 1.0 mm) on the pH, dry residue and myrsinoic acid B (MAB) content of hydroalcoholic extracts by high performance liquid chromatography (HPLC) method. Results: For the extracts, ...

  20. Supercritical carbon dioxide hop extraction

    Directory of Open Access Journals (Sweden)

    Pfaf-Šovljanski Ivana I.

    2005-01-01

    Full Text Available The hop of Magnum cultivar was extracted using supercritical carbon dioxide (SFE-as extractant. Extraction was carried out in the two steps: the first one being carried out at 150 bar and 40°C for 2.5 h (Extract A, and the second was the extraction of the same hop sample at 300 bar and 40°C for 2.5 h (Extract B. Extraction kinetics of the system hop-SFE-CO2 was investigated. Two of four most common compounds of hop aroma (α-humulene and β-caryophyllene were detected in Extract A. Isomerised α-acids and β-acids were detected too. a-Acid content in Extract B was high (that means it is a bitter variety of hop. Mathematical modeling using empirical model characteristic time model and simple single sphere model has been performed on Magnum cultivar extraction experimental results. Characteristic time model equations, best fitted experimental results. Empirical model equation, fitted results well, while simple single sphere model equation poorly approximated the results.

  1. Functional Analysis of Kori Unit 1

    International Nuclear Information System (INIS)

    Choi, Seong Soo; Han, Jeong Hyun; Heo, Tae Young

    2009-07-01

    Function Analysis of Kori Unit 1 has been performed as a part of independent human factors review tasks for control room renovation of the plant. The top level goal defined for the scope of function analysis is 'Generate Electricity'. Through this function analysis of Kori Unit 1, the detailed sub-functions extracted from the existing design documents and procedures, functional relationships among the high level functions, functional classification of each hierarchical level, and tree diagrams of the hierarchical function structures of the plant were developed and identified as the result of the project. In addition, we investigated and compiled the specifications of MMIS devices used in Ulchin Nuclear Power Plant Unit 5,6 in accordance with the request from KAERI. The results of those researches will be used as basis data for independent review of the control room MMIS design of the Kori Unit 1

  2. Membrane extraction instead of solvent extraction - what does it give

    International Nuclear Information System (INIS)

    Macasek, F.

    1989-01-01

    Membrane extraction, i.e. separation in double-emulsion systems, is analyzed theoretically as a three-phase distribution process. Its efficiency is evaluated from the point of view of chemical equilibria and diffusion transport kinetics. The main advantages of membrane extraction as compared with solvent extraction are in higher yields (for preconcentration) and higher capacity for recovery of solutes. A pertraction factor and multiplication factor were defined. They are convenient parameters for numerical characterization of solute distribution, system capacity, process economics, and separation kinetics (both at a linear and non-linear extraction isotherm). 17 refs.; 4 figs

  3. Construction of a supercritical fluid extraction (SFE equipment: validation using annatto and fennel and extract analysis by thin layer chromatography coupled to image

    Directory of Open Access Journals (Sweden)

    Júlio Cezar Flores JOHNER

    2016-01-01

    Full Text Available Abstract The present work describes setting up a laboratory unit for supercritical fluid extraction. In addition to its construction, a survey of cost was done to compare the cost of the homemade unit with that of commercial units. The equipment was validated using an extraction of annatto seeds’ oil, and the extraction and fractionation of fennel oil were used to validate the two separators; for both systems, the solvent was carbon dioxide. The chemical profiles of annatto and fennel extracts were assessed using thin layer chromatography; the images of the chromatographic plates were processed using the free ImageJ software. The cost survey showed that the homemade equipment has a very low cost (~US$ 16,000 compared to commercial equipment. The extraction curves of annatto were similar to those obtained in the literature (yield of 3.8% oil. The separators were validated, producing both a 2.5% fraction of fennel seed extract rich in essential oils and another extract fraction composed mainly of oleoresins. The ImageJ software proved to be a low-cost tool for obtaining an initial evaluation of the chemical profile of the extracts.

  4. Producing ashless coal extracts by microwave irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Ozgur Sonmez; Elife Sultan Giray [Mersin University, Mersin (Turkey). Department of Chemistry

    2011-06-15

    To produce ashless coal extracts, three Turkish coals were extracted with N-methyl-2-pyrrolidinone (NMP), NMP/ethylenediamine (EDA) (17/1, vol/vol) mixture and NMP/tetralin (9/1, vol/vol) mixture through thermal extraction and microwave extraction. Solvent extraction by microwave irradiation (MI) was found to be more effective than that by thermal extraction. Extraction yield of coals in NMP enhanced by addition of a little EDA, but tetralin addition showed variances according to extraction method used. While tetralin addition caused a decrease in the thermal extraction yield, it increased the yield of the extraction by MI. Following the extraction, the solid extracts were produced with ash content ranging from 0.11% to 1.1%. Ash content of solid extract obtained from microwave extraction are less than ash contents of solid extracts obtained from thermal extraction. 34 refs., 7 figs., 5 tabs.

  5. Effet des opérations unitaires d'extraction sur le rendement et la ...

    African Journals Online (AJOL)

    SARAH

    28 févr. 2015 ... J. Appl. Biosci. Effet des opérations unitaires d'extraction sur le rendement et la qualité du beurre de Pentadesma butyracea produit en milieu traditionnel au Bénin. 7977. Effect of unit operations on the extraction yield and quality of the Pentadesma butyracea butter produced in traditional areas of Benin.

  6. On the Optimal Taxation of an Exhaustible Resource Under Monopolistic Extraction

    NARCIS (Netherlands)

    Daubanes, J.

    2007-01-01

    In a simple model of resource depletion (isoelastic demand and constant unit extraction cost), we fully characterize the set of linear effiency-inducing tax/subsidy schemes. We show that this set is infinite and all the larger as the cost of extraction is low. Depending on the magnitude of the

  7. Uranium extraction in phosphoric acid

    International Nuclear Information System (INIS)

    Araujo Figueiredo, C. de

    1984-01-01

    Uranium is recovered from the phosphoric liquor produced from the concentrate obtained from phosphorus-uraniferous mineral from Itataia mines (CE, Brazil). The proposed process consists of two extraction cycles. In the first one, uranium is reduced to its tetravalent state and then extracted by dioctylpyrophosphoric acid, diluted in Kerosene. Re-extraction is carried out with concentrated phosphoric acid containing an oxidising agent to convert uranium to its hexavalent state. This extract (from the first cycle) is submitted to the second cycle where uranium is extracted with DEPA-TOPO (di-2-hexylphosphoric acid/tri-n-octyl phosphine oxide) in Kerosene. The extract is then washed and uranium is backextracted and precipitated as commercial concentrate. The organic phase is recovered. Results from discontinuous tests were satisfactory, enabling to establish operational conditions for the performance of a continuous test in a micro-pilot plant. (Author) [pt

  8. Unsymmetrical phosphate as extractant for the extraction of nitric acid

    International Nuclear Information System (INIS)

    Gaikwad, R.H.; Jayaram, R.V.

    2016-01-01

    Tri-n-butyl phosphate (TBP) was first used as an extractant in 1944, during Manhattan project for the separation of actinides and further explored by Warf in 1949 for the extraction of Ce(IV) from aqueous nitric acid. TBP was further used as an extractant in the Plutonium Uranium Recovery by Extraction (PUREX) process. To meet the stringent requirements of the nuclear industry TBP has been extensively investigated. In spite of its wide applicability, TBP suffers from various disadvantages such as high aqueous solubility, third phase formation, chemical and radiation degradation leading to the formation of undesired products. It also suffers from incomplete decontamination of the actinides from fission products. Various attempts have been made to overcome the problems associated with TBP by way of using higher homologues of TBP such as Tri-iso amyl phosphate (TiAP), Tri-secondary butyl phosphate (TsBP), Tri amyl phosphate (TAP). It was found that in some cases the results were considerably better than those obtained with TBP for uranium/thorium extraction. The extraction of nitric acid by TBP and its higher homologues which are symmetrical are well documented. However, no solvent has emerged clearly superior than TBP. Here in we report the extraction of nitric acid with neutral unsymmetrical phosphates and study them as extractants for the extraction of nitric acid. Dibutyl secbutyl phosphate, dibutyl pentyl phosphate and dibutyl heptyl phosphate were synthesised for this purpose and the extraction of nitric acid was studied in n-dodecane. The results indicate that the substitution of one of the alkyl groups of the symmetrical phosphate adjacent to the phosphoryl (P=O) group of the phosphate does not have any pronounced effect on the extraction capacity of nitric acid. (author)

  9. Peptide Extracts from Cultures of Certain Lactobacilli Inhibit Helicobacter pylori.

    Science.gov (United States)

    De Vuyst, Luc; Vincent, Pascal; Makras, Eleftherios; Leroy, Frédéric; Pot, Bruno

    2010-03-01

    Helicobacter pylori inhibition by probiotic lactobacilli has been observed in vitro and in vivo. Carefully selected probiotic Lactobacillus strains could therefore play an important role in the treatment of H. pylori infection and eradication. However, the underlying mechanism for this inhibition is not clear. The aim of this study was to examine if peptide extracts, containing bacteriocins or other antibacterial peptides, from six Lactobacillus cultures (Lactobacillus acidophilus La1, Lactobacillus amylovorus DCE 471, Lactobacillus casei YIT 9029, Lactobacillus gasseri K7, Lactobacillus johnsonii La1, and Lactobacillus rhamnosus GG) contribute to the inhibition of H. pylori. Peptide extracts from cultures of Lact. amylovorus DCE 471 and Lact. johnsonii La1 were most active, reducing the viability of H. pylori ATCC 43504 with more than 2 log units within 4 h of incubation (P < 0.001). The four other extracts were less or not active. When six clinical isolates of H. pylori were tested for their susceptibility towards five inhibitory peptide extracts, similar observations were made. Again, the peptide extracts from Lact. amylovorus DCE 471 and Lact. johnsonii La1 were the most inhibitory, while the three other extracts resulted in a much lower inhibition of H. pylori. Protease-treated extracts were inactive towards H. pylori, confirming the proteinaceous nature of the inhibitory substance.

  10. New extraction technique for alkaloids

    Directory of Open Access Journals (Sweden)

    Djilani Abdelouaheb

    2006-01-01

    Full Text Available A method of extraction of natural products has been developed. Compared with existing methods, the new technique is rapid, more efficient and consumes less solvent. Extraction of alkaloids from natural products such as Hyoscyamus muticus, Datura stramonium and Ruta graveolens consists of the use of a sonicated solution containing a surfactant as extracting agent. The alkaloids are precipitated by Mayer reagent, dissolved in an alkaline solution, and then extracted with chloroform. This article compares the results obtained with other methods showing clearly the advantages of the new method.

  11. ANTHOCYANINS ALIPHATIC ALCOHOLS EXTRACTION FEATURES

    Directory of Open Access Journals (Sweden)

    P. N. Savvin

    2015-01-01

    Full Text Available Anthocyanins red pigments that give color a wide range of fruits, berries and flowers. In the food industry it is widely known as a dye a food additive E163. To extract from natural vegetable raw materials traditionally used ethanol or acidified water, but in same technologies it’s unacceptable. In order to expand the use of anthocyanins as colorants and antioxidants were explored extracting pigments alcohols with different structures of the carbon skeleton, and the position and number of hydroxyl groups. For the isolation anthocyanins raw materials were extracted sequentially twice with t = 60 C for 1.5 hours. The evaluation was performed using extracts of classical spectrophotometric methods and modern express chromaticity. Color black currant extracts depends on the length of the carbon skeleton and position of the hydroxyl group, with the alcohols of normal structure have higher alcohols compared to the isomeric structure of the optical density and index of the red color component. This is due to the different ability to form hydrogen bonds when allocating anthocyanins and other intermolecular interactions. During storage blackcurrant extracts are significant structural changes recoverable pigments, which leads to a significant change in color. In this variation, the stronger the higher the length of the carbon skeleton and branched molecules extractant. Extraction polyols (ethyleneglycol, glycerol are less effective than the corresponding monohydric alcohols. However these extracts saved significantly higher because of their reducing ability at interacting with polyphenolic compounds.

  12. Supercritical fluid extraction of uranium

    International Nuclear Information System (INIS)

    Kumar, Pradeep

    2017-01-01

    Uranium being strategic material, its separation and purification is of utmost importance in nuclear industry, for which solvent extraction is being employed. During solvent extraction significant quantity of radioactive liquid waste gets generated which is of environmental concern. In recent decades supercritical fluid extraction (SFE) has emerged as promising alternative to solvent extraction owing to its inherent advantage of reduction in liquid waste generation and simplification of process. In this paper a brief overview of research work carried out so far on SFE of uranium by BARC has been given

  13. Plutonium and americium extraction studies with bifunctional organophosphorus extractants

    International Nuclear Information System (INIS)

    Navratil, J.D.

    1985-01-01

    Neutral bifunctional organophosphorus extractants, such as octylphenyl-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) and dihexyl-N,N-diethylcarbamoylmethylphosphonate (CMP), are under study at the Rocky Flats Plant (RFP) to remove plutonium and americium from the 7M nitric acid waste. These compounds extract trivalent actinides from strong nitric acid, a property which distinguishes them from monofunctional organiphosphorus reagents. Furthermore, the reagents extract hydroytic plutonium (IV) polymer which is present in the acid waste stream. The compounds extract trivalent actinides with a 3:1 stoichiometry, whereas tetra- and hexavalent actinides extract with a stoichiometry of 2:1. Preliminary studies indicate that the extracted plutonium polymer complex contains one to two molecules of CMP per plutonium ion and the plutonium(IV) maintains a polymeric structure. Recent studies by Horwitz and co-workers conclude that the CMPO and CMP reagents behave as monodentate ligands. At RFP, three techniques are being tested for using CMP and CMPO to remove plutonium and americium from nitric acid waste streams. The different techniques are liquid-liquid extraction, extraction chromatography, and solid-supported liquid membranes. Recent tests of the last two techniques will be briefly described. In all the experiments, CMP was an 84% pure material from Bray Oil Co. and CMPO was 98% pure from M and T Chemicals

  14. determination of lipophilic extractives in ionic liquid extracts

    African Journals Online (AJOL)

    dell

    Chem. 9: 63-69. Freire CSR, Pinto PCR, Santiago AS,. Silvestre AJD, Evtuquin DV and Neto. CP 2006a Comparative study of lipophilic extractives of hardwoods and corresponding ECF bleached kraft pulps. BioResources. 1: 3-17. Freire CSR, Silvestre AJD and Neto CP. 2005. Lipophilic extractives in. Eucalyptus globulus.

  15. Hepatoprotective Activity of Easter Lily (Lilium longiflorum Thunb.) Bulb Extracts.

    Science.gov (United States)

    Tang, Wenping; Munafo, John P; Palatini, Kimberly; Esposito, Debora; Huang, Mou-Tuan; Komarnytsky, Slavko; Ho, Chi-Tang; Gianfagna, Thomas J

    2015-11-11

    The hepatoprotective activities of two different extracts, a hydroethanolic crude bulb extract (CB) and a steroidal glycoside-rich 1-butanol extract (BuOH), prepared from the bulbs of Easter lily (Lilium longiflorum Thunb.), were evaluated in a 24 week study in the female KK.Cg-A(y)/J Type 2 diabetic mouse model. Animals were divided into six groups (n = 16): control mice received Easter lily bulb extract-free drinking water together with a low- or high-fat diet (diabetic control); drinking water for the remaining groups was supplemented with CB extract (1%), BuOH extract (0.1 or 0.2%), and reference drug Metformin (0.001%), together with a high-fat diet. Both CB and BuOH extract treatment groups exhibited significantly improved liver function based on comparisons of triglycerides [diabetic 219 ± 34 mg/dL, CB 131 ± 27 mg/dL, BuOH(0.2%) 114 ± 35 mg/dL], CB total cholesterol (TC) (diabetic 196 ± 12 mg/dL, CB 159 ± 5 mg/dL), average liver mass [diabetic 2.96 ± 0.13 g, CB 2.58 ± 0.08 g, BuOH(0.1%) 2.48 ± 0.13 g], alanine transferase [diabetic 74 ± 5 units/L, CB 25 ± 1 units/L, BuOH(0.1%) 45 ± 1 units/L], and histological examinations. Glucose metabolism was improved only in CB, which was confirmed by oral glucose tolerance tests (OGTT) in diet-induced obese C57BL/6J mice exposed to CB extract. These data suggest that steroidal glycosides 1-5 might play a role in the hepatoprotective activity of the BuOH extracts, while the results of the TC measurements and OGTT study indicate that other constituents present in the CB extract are responsible for its hypocholesterolemic and hypoglycemic activity.

  16. Extraction by means of emulsified liquid membranes; Extraction par membranes liquides emulsionnees (MLE)

    Energy Technology Data Exchange (ETDEWEB)

    Pareau, D.; Stambouli, M. [Ecole Centrale de Paris, 75 (France)

    2006-12-15

    It is an alternative of the liquid-liquid extraction process where extraction and stripping are simultaneously carried out. The stripping solution is dispersed in the solvent in micro-droplets. This emulsion, stabilised by a surface-active agent, is then dispersed in the liquid to be treated and, during that step, the metal is transferred to the stripping solution, moving through the solvent which operates as an organic membrane. The paper describes in detail the mechanism of the process, its advantages and its disadvantages. Its field of applications is wide, but only a few units are now industrially in operation, most of them exists only at the pilot scale. It is particularly adapted for the treatment of effluents with a very low content in metallic impurities. As examples, the paper describes the recovery of zinc from viscose plant effluents (Lenzing plant, Austria) and the removal of free cyanide ions and cyanide metallic complexes (pilot scale). (authors)

  17. Nonlocal Intracranial Cavity Extraction

    Science.gov (United States)

    Manjón, José V.; Eskildsen, Simon F.; Coupé, Pierrick; Romero, José E.; Collins, D. Louis; Robles, Montserrat

    2014-01-01

    Automatic and accurate methods to estimate normalized regional brain volumes from MRI data are valuable tools which may help to obtain an objective diagnosis and followup of many neurological diseases. To estimate such regional brain volumes, the intracranial cavity volume (ICV) is often used for normalization. However, the high variability of brain shape and size due to normal intersubject variability, normal changes occurring over the lifespan, and abnormal changes due to disease makes the ICV estimation problem challenging. In this paper, we present a new approach to perform ICV extraction based on the use of a library of prelabeled brain images to capture the large variability of brain shapes. To this end, an improved nonlocal label fusion scheme based on BEaST technique is proposed to increase the accuracy of the ICV estimation. The proposed method is compared with recent state-of-the-art methods and the results demonstrate an improved performance both in terms of accuracy and reproducibility while maintaining a reduced computational burden. PMID:25328511

  18. Nonlocal Intracranial Cavity Extraction

    Directory of Open Access Journals (Sweden)

    José V. Manjón

    2014-01-01

    Full Text Available Automatic and accurate methods to estimate normalized regional brain volumes from MRI data are valuable tools which may help to obtain an objective diagnosis and followup of many neurological diseases. To estimate such regional brain volumes, the intracranial cavity volume (ICV is often used for normalization. However, the high variability of brain shape and size due to normal intersubject variability, normal changes occurring over the lifespan, and abnormal changes due to disease makes the ICV estimation problem challenging. In this paper, we present a new approach to perform ICV extraction based on the use of a library of prelabeled brain images to capture the large variability of brain shapes. To this end, an improved nonlocal label fusion scheme based on BEaST technique is proposed to increase the accuracy of the ICV estimation. The proposed method is compared with recent state-of-the-art methods and the results demonstrate an improved performance both in terms of accuracy and reproducibility while maintaining a reduced computational burden.

  19. Study on the extraction kinetics of U(IV) extraction with neutral phosphoric extractant

    International Nuclear Information System (INIS)

    Lin Zhou; Liao Shishu; Li Zhou

    1995-04-01

    The extraction kinetics of U(IV) in the diisooctyl isobutylphosphonate system has been studied by using the single drop method. The effects of the concentrations of U(IV), HCl and extractant on the extraction rate have been examined. In a certain HCl concentration, the extraction rate equation has been acquired and in the condition of various HCl concentration the extraction rate of U(IV) is proportional to [HCl 1.51 . The effect of operation temperature was also examined, and the calculated apparent activation energy is equal to 23.24 kJ/mol. From the experimental results, the extraction reaction process and the rate-controlling step have been deduced. (4 figs., 5 tabs.)

  20. Unit Cost Compendium Calculations

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Unit Cost Compendium (UCC) Calculations raw data set was designed to provide for greater accuracy and consistency in the use of unit costs across the USEPA...

  1. United States housing, 2012

    Science.gov (United States)

    Delton Alderman

    2013-01-01

    Provides current and historical information on housing market in the United States. Information includes trends for housing permits and starts, housing completions for single and multifamily units, and sales and construction. This report will be updated annually.

  2. United Cerebral Palsy

    Science.gov (United States)

    ... your local affiliate Find your local affiliate United Cerebral Palsy United Cerebral Palsy (UCP) is a trusted resource for individuals with Cerebral Palsy and other disabilities and their networks. Individuals with ...

  3. Malaria Treatment (United States)

    Science.gov (United States)

    ... Providers, Emergency Consultations, and General Public. Contact Us Malaria Treatment (United States) Recommend on Facebook Tweet Share Compartir Treatment of Malaria: Guidelines For Clinicians (United States) Download PDF version ...

  4. Standard Operation Procedure of Gaharu Oil Extraction Process

    International Nuclear Information System (INIS)

    Peng, C.S.; Mohd Fajri Osman; Norella Bahari; Rusli Zakaria

    2015-01-01

    Gaharu oil extraction system developed by Nuclear Malaysia is a hydro-distillation system innovated from the tradition method and improvised with science and technology to enhance the process efficiency and safety. The main component of gaharu oil extraction system included the extraction vessel, condenser and collection decanter. Apart from the extraction unit, the gaharu oil extraction process also incorporated two major supporting systems. These systems are the liquefied petroleum gas (LPG) system and the water cooling system. The LPG system is solely used for heating the vessel, which contains a mixture of treated and grind gaharu bark and fluid, to produce steam. Meanwhile the water cooling system is used to supply the necessary cool water into the condenser unit and facilitate in the transformation of the mentioned steam into gaharu oil and distilled water. The dissipate water from this process will be channeled back into the water cooling ponds to let excess heat to be removed and allow the cool water to reuse again by the process. (author)

  5. Effect of soybean extract after tooth extraction on osteoblast numbers

    Directory of Open Access Journals (Sweden)

    Rosa Sharon Suhono

    2011-06-01

    Full Text Available Background: Many researches were done to find natural materials that may increase and promote bone healing processes after trauma and surgery. One of natural material that had been studied was soybean extract which contains phytoestrogen, a non-steroidal compounds found in plants that may binds to estrogen receptors and have estrogen-like activity. Purpose: The aim of this study was to investigate the effect of soybean extract feeding on the number of osteoblast cells in alveolar bone socket after mandibular tooth extraction. Methods: This study was studied on male Rattus norvegicus strain Wistar. Seventeen rats divided into three groups were used in this study. Group 1 fed with carboxy methyl cellulose (CMC solution 0,2% for seven days, and the left mandibular central incisivus was extracted; group 2 fed with soybean extract for seven days and the left mandibular central incisives was extracted; group 3 received the left mandibular central incisives extraction followed by soybean extract feeding for seven days after the extraction. All groups were sacrificed on the seventh day post-extraction, and the alveolar bone sockets were taken for histopathological observation. The tissues were processed and stained using hematoxylin and eosin to identify the amount of osteoblast cells. The number of osteoblast cells was counted using an Image Tool program. The data was analyzed statistically using the One-Way ANOVA test. Results: Significant differences were found on the number of osteoblast cells in alveolar bone after tooth extraction between groups. Group 2 (fed with soybean extract is higher than group 1 (fed with CMC and group 3 (fed with soybean extract after extraction. Conclusion: Soybean extract feeding that given for seven days pre-tooth extraction can increase the number of osteoblast cells compared with the group that were not given soybean extract feeding and also with the group that were given soybean extract feeding for seven days post

  6. Extraction systems of the SPS

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    A pair of prototype septum magnets for the extraction systems of the SPS. Each of the two extraction systems will contain eighteen of these septum magnets (eight with a 4 mm septum and ten with a 16 mm septum) mounted in pairs in nine vacuum tanks.

  7. [Endoscopic extraction of gallbladder calculi].

    Science.gov (United States)

    Kühner, W; Frimberger, E; Ottenjann, R

    1984-06-29

    Endoscopic extraction of gallbladder stones were performed, as far as we know for the first time, in three patients with combined choledochocystolithiasis. Following endoscopic papillotomy (EPT) and subsequent mechanical lithotripsy of multiple choledochal concrements measuring up to 3 cm the gallbladder stones were successfully extracted with a Dormia basket through the cystic duct. The patients have remained free of complications after the endoscopic intervention.

  8. Extractive separation of tellurium(4)

    International Nuclear Information System (INIS)

    Gawali, S.B.; Shinde, V.M.

    1977-01-01

    A method is described for the extraction of tellurium (4) from hydrobromic acid media using 4-methyl-2-pentanol as an extractant. The method affords the determination of tellurium after its separation from Se, Au, Cu, Pb, Fe, Os, V and Al. (author)

  9. Solids recycling in solvent extraction

    International Nuclear Information System (INIS)

    Robinson, L.F.

    1980-01-01

    In an extraction process for extracting values from a first stream into a substantially immiscible second stream using a multi-compartmental rotary contactor, unwanted solids formed in the contactor and discharged at least partly with the the first stream are separated and re-entered into the contactor intermediate the points at which the streams are discharged. (author)

  10. Sample Results from the Interim Salt Disposition Program Macrobatch 8 Tank 21H Qualification Samples

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Washington, A. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-01-01

    Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Macrobatch (Salt Batch) 8 for the Interim Salt Disposition Program (ISDP). An Actinide Removal Process (ARP) and several Extraction-Scrub- Strip (ESS) tests were also performed. This document reports characterization data on the samples of Tank 21H as well as simulated performance of ARP and the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). No issues with the projected Salt Batch 8 strategy are identified. A demonstration of the monosodium titanate (MST) (0.2 g/L) removal of strontium and actinides provided acceptable average decontamination factors for plutonium of 2.62 (4 hour) and 2.90 (8 hour); and average strontium decontamination factors of 21.7 (4 hour) and 21.3 (8 hour). These values are consistent with results from previous salt batch ARP tests. The two ESS tests also showed acceptable performance with extraction distribution ratios (D(Cs)) values of 52.5 and 50.4 for the Next Generation Solvent (NGS) blend (from MCU) and NGS (lab prepared), respectively. These values are consistent with results from previous salt batch ESS tests. Even though the performance is acceptable, SRNL recommends that a model for predicting extraction behavior for cesium removal for the blended solvent and NGS be developed in order to improve our predictive capabilities for the ESS tests.

  11. Sample results from the Interim Salt Disposition Program Macrobatch 8 Tank 21H qualification samples

    Energy Technology Data Exchange (ETDEWEB)

    Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Washington, II, A. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-01-13

    Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Macrobatch (Salt Batch) 8 for the Interim Salt Disposition Program (ISDP). An Actinide Removal Process (ARP) and several Extraction-Scrub-Strip (ESS) tests were also performed. This document reports characterization data on the samples of Tank 21H as well as simulated performance of ARP and the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU). No issues with the projected Salt Batch 8 strategy are identified. A demonstration of the monosodium titanate (MST) (0.2 g/L) removal of strontium and actinides provided acceptable average decontamination factors for plutonium of 2.62 (4 hour) and 2.90 (8 hour); and average strontium decontamination factors of 21.7 (4 hour) and 21.3 (8 hour). These values are consistent with results from previous salt batch ARP tests. The two ESS tests also showed acceptable performance with extraction distribution ratios (D(Cs)) values of 52.5 and 50.4 for the Next Generation Solvent (NGS) blend (from MCU) and NGS (lab prepared), respectively. These values are consistent with results from previous salt batch ESS tests. Even though the performance is acceptable, SRNL recommends that a model for predicting extraction behavior for cesium removal for the blended solvent and NGS be developed in order to improve our predictive capabilities for the ESS tests.

  12. Development of blood extraction system for health monitoring system

    Science.gov (United States)

    Tsuchiya, Kazuyoshi; Nakanishi, Naoyuki; Nakamachi, Eiji

    2004-03-01

    The purpose of this research is to develop the compact human blood sampling device applied for a health monitoring system(HMS), which is called "Mobile Hospital". The HMS consists of (1) a micro electrical pumping system for blood extraction, (2) a bio-sensor to detect and evaluate an amount of Glucose, Cholesterol and Urea in extracted blood, by using enzyme such as Glucoseoxidase (GOD), Cholesteroloxidase and Urease. The mechanical design elements of the device are bio-compatible microneedle, indentation unit using a shape memory alloy(SMA) actuator and pumping unit using a piezoelectric microactuator. The design concept is the biomimetic micromachine of female mosquito"s blood sampling mechanism. The performances of the main mechanical elements such as indentation force of the microneedle, actual stroke of the indentation unit using a SMA actuator and liquid sampling ability of the pumping unit using PZT piezoelectric microactuator were measured. The 3 mm stroke of the indentation load generated by SMA actuator was 0.8mN. The amount of imitation blood extracted by using bimorph PZT actuators was about 0.5 microliters for 10 sec. A 60-micrometer outer diameter and 25-micrometer inner diameter Titanium microneedle, which size is same as female mosquito"s labium, was produced by sputter deposition.

  13. Process for producing fuel grade ethanol by continuous fermentation, solvent extraction and alcohol separation

    Science.gov (United States)

    Tedder, Daniel W.

    1985-05-14

    Alcohol substantially free of water is prepared by continuously fermenting a fermentable biomass feedstock in a fermentation unit, thereby forming an aqueous fermentation liquor containing alcohol and microorganisms. Continuously extracting a portion of alcohol from said fermentation liquor with an organic solvent system containing an extractant for said alcohol, thereby forming an alcohol-organic solvent extract phase and an aqueous raffinate. Said alcohol is separated from said alcohol-organic solvent phase. A raffinate comprising microorganisms and unextracted alcohol is returned to the fermentation unit.

  14. Parallel artificial liquid membrane extraction

    DEFF Research Database (Denmark)

    Gjelstad, Astrid; Rasmussen, Knut Einar; Parmer, Marthe Petrine

    2013-01-01

    This paper reports development of a new approach towards analytical liquid-liquid-liquid membrane extraction termed parallel artificial liquid membrane extraction. A donor plate and acceptor plate create a sandwich, in which each sample (human plasma) and acceptor solution is separated by an arti......This paper reports development of a new approach towards analytical liquid-liquid-liquid membrane extraction termed parallel artificial liquid membrane extraction. A donor plate and acceptor plate create a sandwich, in which each sample (human plasma) and acceptor solution is separated...... by an artificial liquid membrane. Parallel artificial liquid membrane extraction is a modification of hollow-fiber liquid-phase microextraction, where the hollow fibers are replaced by flat membranes in a 96-well plate format....

  15. Uranium extraction from phosphoric acid

    International Nuclear Information System (INIS)

    Lounis, A.

    1983-05-01

    A study has been carried out for the extraction of uranium from phosphoric acid produced in Algeria. First of all, the Algerian phosphoric acid produced in Algeria by SONATRACH has been characterised. This study helped us to synthesize a phosphoric acid that enabled us to pass from laboratory tests to pilot scale tests. We have then examined extraction and stripping parameters: diluent, DZEPHA/TOPO ratio and oxidising agent. The laboratory experiments enabled us to set the optimum condition for the choice of diluent, extractant concentration, ratio of the synergic mixture, oxidant concentration, redox potential. The equilibrium isotherms lead to the determination of the number of theoretical stages for the uranium extraction and stripping of uranium, then the extraction from phosphoric acid has been verified on a pilot scale (using a mixer-settler)

  16. Improving IUE High Dispersion Extraction

    Science.gov (United States)

    Lawton, Patricia J.; VanSteenberg, M. E.; Massa, D.

    2007-01-01

    We present a different method to extract high dispersion International Ultraviolet Explorer (IUE) spectra from the New Spectral Image Processing System (NEWSIPS) geometrically and photometrically corrected (SI HI) images of the echellogram. The new algorithm corrects many of the deficiencies that exist in the NEWSIPS high dispersion (SIHI) spectra . Specifically, it does a much better job of accounting for the overlap of the higher echelle orders, it eliminates a significant time dependency in the extracted spectra (which can be traced to the background model used in the NEWSIPS extractions), and it can extract spectra from echellogram images that are more highly distorted than the NEWSIPS extraction routines can handle. Together, these improvements yield a set of IUE high dispersion spectra whose scientific integrity is sign ificantly better than the NEWSIPS products. This work has been supported by NASA ADP grants.

  17. Extraction of toxic and valuable metals from foundry sands

    International Nuclear Information System (INIS)

    Vite T, J.

    1996-01-01

    There were extracted valuable metals from foundry sands such as: gold, platinum, silver, cobalt, germanium, nickel and zinc among others, as well as highly toxic metals such as chromium, lead, vanadium and arsenic. The extraction efficiency was up to 100% in some cases. For this reason there were obtained two patents at the United States, patent number 5,356,601, in October 1994, given for the developed process and patent number 5,376,000, in December 1994, obtained for the equipment employed. Therefore, the preliminary parameters for the installation of a pilot plant have also been developed. (Author)

  18. Selectivity in extraction of copper and indium with chelate extractants

    International Nuclear Information System (INIS)

    Zivkovic, D.

    2003-01-01

    Simultaneous extraction of copper and indium with chelate extractants (LIX84 and D2E11PA) was described. Stechiometry of metal-organic complexes examined using the method of equimolar ratios resulted in CuR 2 and InR 3 forms of hydrophobic extracting species. A linear correlation was obtained between logarithm of distribution coefficients and chelate agents and pH, respectively. Selectivity is generally higher with higher concentrations of chelate agents in the organic phase, and is decreased with increase of concentration of hydrogen ions in feeding phase. (Original)

  19. Selective extraction of natural bitumen

    International Nuclear Information System (INIS)

    Starshov, M.; Starshov, I.

    1991-01-01

    The work performed in the field of natural bitumen extraction is aimed at maximum separation of organic phase. On treating bituminous rocks with solvents, the associated metals are extracted together with the organic phase and may further exert a negative effect on refining of natural bitumen. the authors propose a simplified two stage technique for the extraction of bitumen which enables to utilize V and Ni contained in the concentrate of the second stage extraction (Table). At the first stage, negative bitumen is extracted with the summary content of metals not exceeding 0.005%. This allows to avoid de metallization of native bitumen and subject it to treatment by catalytic cracking. during this stage gasoline and kerosene fractions, different oil distillates and condensates can be used as solvents. at the second stage, aromatic and halo id compounds bearing wastes and by-products, i.e. cheap and non deficient reagents, serve as solvents. The technology was tested under laboratory conditions using Tatar bituminous sands. It is also possible to use one solvent only, however, on condition that at first the oil product with the summary metal content below 0.005%, and then the remaining product is extracted. The proposed technology has proved so universal that it can be applied to refining any type of raw material to be found in the territory of the Tatar republic, using surface extraction complexes. (author). 9 refs., tab

  20. Selective solvent extraction of oils

    Energy Technology Data Exchange (ETDEWEB)

    1938-04-09

    In the selective solvent extraction of naphthenic base oils, the solvent used consists of the extract obtained by treating a paraffinic base oil with a selective solvent. The extract, or partially spent solvent is less selective than the solvent itself. Selective solvents specified for the extraction of the paraffinic base oil are phenol, sulphur dioxide, cresylic acid, nitrobenzene, B:B/sup 1/-dichlorethyl ether, furfural, nitroaniline and benzaldehyde. Oils treated are Coastal lubricating oils, or naphthenic oils from the cracking, or destructive hydrogenation of coal, tar, lignite, peat, shale, bitumen, or petroleum. The extraction may be effected by a batch or counter-current method, and in the presence of (1) liquefied propane, or butane, or naphtha, or (2) agents which modify the solvent power such as, water, ammonia, acetonitrile, glycerine, glycol, caustic soda or potash. Treatment (2) may form a post-treatment effected on the extract phase. In counter-current treatment in a tower some pure selective solvent may be introduced near the raffinate outlet to wash out any extract therefrom.

  1. Analysis of human muscle extracts by proton NMR

    International Nuclear Information System (INIS)

    Venkatasubramanian, P.N.; Barany, M.; Arus, C.

    1986-01-01

    Perchloric acid extracts were prepared from pooled human muscle biopsies from patients diagnosed with scoliosis (SCOL) and cerebral palsy (CP). After neutralization with KOH and removal of perchlorate, the extracts were concentrated by freeze drying and dissolved in 2 H 2 O to contain 120 O.D. units at 280 nm per 0.5 ml. 1 H NMR spectroscopy was performed with the 5 mm probe of a Varian XL300 instrument. Creatine, lactate, carnosine, and choline were the major resonances in the one-dimensional spectra of both extracts. With creatine as reference, 2.5-fold more lactate was found in SCOL than in CP, and a much smaller difference was also found in their carnosine content. Two-dimensional COSY comparison revealed several differences between the two extracts. Taurine, N-acetyl glutamate, glycerophosphoryl choline (or phosphoryl choline) and an unidentified spot were present only in the extract from SCOL but not in that from CP. On the other hand, aspartate, hydroxy-proline, carnitine and glycerophosphoryl ethanolamine were only present in CP but absent in SCOL. Alanine, cysteine, lysine and arginine appeared in both extracts without an apparent intensity difference

  2. Manufacture of electrostatic septum for extracting particle beam

    International Nuclear Information System (INIS)

    Tokumoto, Shuichi

    1979-01-01

    In the main ring of National Laboratory for High Energy Physics, fast and slow extractions of accelerated proton beam are carried out by using electrostatic septa. The electrostatic septum is an apparatus to deflect beam by an electrostatic field, basically composed of a couple of parallel plate electrodes installed in a vacuum chamber. The electrostatic septum is required to satisfy the following two conditions: it must be very thin and flat to reduce the loss of extracted beam, and sufficiently high electric field must be generated to deflect beam in a limited length. The structure and manufacture of electrostatic septa are described. The manufacturing is explained by dividing a septum into an anode and a cathode, terminals introducing high voltage, a vacuum chamber, and high voltage circuit. The performance is also described on the experiments for no-beam condition and beam extraction. Beam extraction has been carried out over 1500 hours thus far, the average beam intensity being 1 x 10 12 ppp, and extraction efficiency more than 90%. There have been no serious failure to affect the performance nor metal wire breakage. They have satisfied their purposes, being used for both fast and slow extractions. Presently, lengthening of the electrostatic field region is being planned to increase the length of the septa to 1.5 m per unit. (Wakatsuki, Y.)

  3. Age of patient at the extraction of the third molar.

    Science.gov (United States)

    Kautto, A; Vehkalahti, M M; Ventä, I

    2018-04-13

    The purpose of this study was to assess the age of patients at the time of extraction of third molars. Our data included all routine and surgical extractions of third molars (n=8199 teeth) performed by general and specialist dentists of the public oral health services of the city of Helsinki over the period 2013-2014. Measurements included patient's age, gender, the identified third molar, the type of anaesthesia, the method of extraction, and the diagnosis at extraction. Patients' ages ranged from 10 to 99years. We found significant differences between younger and older age groups: third molar extractions occurred more often for women than for men below the age of 30years (Page of 40years, but the corresponding prevalences reversed after the age of 40years. Diagnoses at extraction differed between younger and older patients. We conclude that the treatment pattern of third molars at public health services varies greatly over a lifetime, and that a greater variety exists than had been reported previously from oral and maxillofacial units. Copyright © 2018 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  4. Extraction of uranium with emulsion membrane process use tributylphosphate extractant

    International Nuclear Information System (INIS)

    Basuki, K.T.; Sudibyo, R.; Bambang EHB; Muhadi, A.W.

    1996-01-01

    To increase the effectiveness of extraction process with so for to occur, it was tried the extraction with a couple of extraction and stripping process. This couple process was called liquid membrane emulsion. As membrane was used mix surfactant (Span-80), tributylphosphate in kerosene, natrium carbonate, while as a feeder was uranium solution with 500 concentration ppm in 0.5 - 3 M nitrate acid. In this experiment the variable investigated were % surfactant (1 - 5 %), rotary speed for membrane making (2,500 - 10.000 rpm). The optimal condition result of experiment were 5 % surfactant, 3 M nitrate acid, rotary speed 10.000 rpm and (Kd eksU ) 57 %, and (Kd strippU ) 87 %, Kd eksU at liquid-liquid extraction is 44 %. (author)

  5. Evaluation of extractants and chelating resins in polishing actinide-contaminated waste streams

    International Nuclear Information System (INIS)

    Schreiber, S.B.; Dunn, S.L.; Yarbro, S.L.

    1991-06-01

    At the Los Alamos National Laboratory Plutonium Facility, anion exchange is used for recovering plutonium from nitric acid solutions. Although this approach recovers >99%, the trace amounts of plutonium and other actinides remaining in the effluent require additional processing. We are doing research to develop a secondary unit operation that can directly polish the effluent so that actinide levels are reduced to below the maximum allowed for facility discharge. We selected solvent extraction, the only unit operation that can meet the stringent process requirements imposed; several carbonyl and phosphoryl extractants were evaluated and their performance characterized. We also investigated various engineering approaches for solvent extraction; the most promising was a chelating resin loaded with extractant. Our research now focuses on the synthesis of malonamides, and our goal is to bond these extractants to a resin matrix. 7 refs., 12 figs., 1 tab

  6. CONVERSION EXTRACTION DESULFURIZATION (CED) PHASE III

    Energy Technology Data Exchange (ETDEWEB)

    James Boltz

    2005-03-01

    This project was undertaken to refine the Conversion Extraction Desulfurization (CED) technology to efficiently and economically remove sulfur from diesel fuel to levels below 15-ppm. CED is considered a generic term covering all desulfurization processes that involve oxidation and extraction. The CED process first extracts a fraction of the sulfur from the diesel, then selectively oxidizes the remaining sulfur compounds, and finally extracts these oxidized materials. The Department of Energy (DOE) awarded Petro Star Inc. a contract to fund Phase III of the CED process development. Phase III consisted of testing a continuous-flow process, optimization of the process steps, design of a pilot plant, and completion of a market study for licensing the process. Petro Star and the Degussa Corporation in coordination with Koch Modular Process Systems (KMPS) tested six key process steps in a 7.6-centimeter (cm) (3.0-inch) inside diameter (ID) column at gas oil feed rates of 7.8 to 93.3 liters per hour (l/h) (2.1 to 24.6 gallons per hour). The team verified the technical feasibility with respect to hydraulics for each unit operation tested and successfully demonstrated pre-extraction and solvent recovery distillation. Test operations conducted at KMPS demonstrated that the oxidation reaction converted a maximum of 97% of the thiophenes. The CED Process Development Team demonstrated that CED technology is capable of reducing the sulfur content of light atmospheric gas oil from 5,000-ppm to less than 15-ppm within the laboratory scale. In continuous flow trials, the CED process consistently produced fuel with approximately 20-ppm of sulfur. The process economics study calculated an estimated process cost of $5.70 per product barrel. The Kline Company performed a marketing study to evaluate the possibility of licensing the CED technology. Kline concluded that only 13 refineries harbored opportunity for the CED process. The Kline study and the research team's discussions

  7. Actinides complexes in solvent extraction. The amide type of extractants

    International Nuclear Information System (INIS)

    Musikas, C.; Condamines, N.; Charbonnel, M.C.; Hubert, H.

    1989-01-01

    The N,N-dialkylamides and the N,N'-tetraalkyl. 2-alkyl 1,3-diamide propane are two promising classes of extractants which could replace advantageously the organophosphorus molecules for the separations of the actinide. The main advantages of the amides lie in their complete incinerability and the small interference of their radiolytic and hydrolytic degradation products for the processes. The actinide extraction chemistry with various amides is reviewed in this paper

  8. Adult orthodontic therapy: extraction versus non-extraction.

    Science.gov (United States)

    Baumrind, S

    1998-11-01

    This study addresses the problem of randomization of subjects with respect to an irreversible aspect of treatment strategy, namely, the extraction of teeth. The investigation includes both prospective and retrospective components. The data presented focus on clinician decision-making. Of the 1321 potential subjects for whom records were taken, 250 met the inclusion criteria. Of these subjects, 82 declined to participate and 20 were dropped because of difficulty in obtaining five independent evaluations of their records within a reasonable time frame. Thus, the final sample contained 148 subjects. Approximately one-third of the subjects in the sample are adult, somewhat more than half are female, and Class I malocclusions outnumber Class II malocclusions by a count of 95 to 53. Patterns of agreement and disagreement among five clinicians include: a) agreement/disagreement on the primary decision whether or not to extract: the data reveal a strong tendency towards consensus among the clinicians; b) agreement/disagreement on extraction pattern in patients in whom the clinician believes that extraction is indicated: the clinicians tended strongly to agree on extraction pattern; c) agreement/disagreement on the need for adjunctive orthognathic surgery: decisions favoring surgery were more common and more 'definite' than 'probable' in the adult cohort than in the adolescent cohort but this tendency was not as strong as had been anticipated; d) agreement/disagreement concerning Angle classification: disagreements were more common than had been anticipated; and e) differences among the individual clinicians as to their ratios of extraction/non-extraction decisions: overall, clinicians opted for extraction less frequently in the adolescent cohort than in the adult cohort (55 vs. 66%). Because the data are drawn from actual clinical experience, the conclusions involve a number of assumptions and their generalizability should be evaluated.

  9. Antimycobacterial Efficacy of Andrographis paniculata Leaf Extracts Under Intracellular and Hypoxic Conditions.

    Science.gov (United States)

    Bhatter, Purva; Gupta, Pooja; Daswani, Poonam; Tetali, Pundarikakshudu; Birdi, Tannaz

    2015-01-01

    The inhibition of the growth of Mycobacterium tuberculosis by the extracts of Andrographis paniculata has been studied using intracellular and axenic hypoxic conditions. The inhibition (confirmed using the gold standard colony forming unit assay) was found to increase with "double stimuli" or higher concentration of the extract. Organic solvent extracts were found to inhibit bacterial growth more than the aqueous extracts under microaerophilic conditions mimicked through axenic and intracellular assays. This could be further explored to evaluate the potential of the plant to be used against nonreplicating/dormant bacilli. © The Author(s) 2014.

  10. Geochemical Modeling of ILAW Lysimeter Water Extracts

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-12-22

    Geochemical modeling results of water extracts from simulated immobilized low-activity waste (ILAW) glasses, placed in lysimeters for eight years suggest that the secondary phase reaction network developed using product consistency test (PCT) results at 90°C may need to be modified for field conditions. For sediment samples that had been collected from near the glass samples, the impact of glass corrosion could be readily observed based upon the pH of their water extracts. For unimpacted sediments the pH ranged from 7.88 to 8.11 with an average of 8.04. Sediments that had observable impacts from glass corrosion exhibited elevated pH values (as high as 9.97). For lysimeter sediment samples that appear to have been impacted by glass corrosion to the greatest extent, saturation indices determined for analcime, calcite, and chalcedony in the 1:1 water extracts were near equilibrium and were consistent with the secondary phase reaction network developed using PCT results at 90°C. Fe(OH)3(s) also appears to be essentially at equilibrium in extracts impacted by glass corrosion, but with a solubility product (log Ksp) that is approximately 2.13 units lower than that used in the secondary phase reaction network developed using PCT results at 90°C. The solubilities of TiO2(am) and ZrO2(am) also appear to be much lower than that assumed in the secondary phase reaction network developed using PCT results at 90°C. The extent that the solubility of TiO2(am) and ZrO2(am) were reduced relative to that assumed in the secondary phase reaction network developed using PCT results at 90°C could not be quantified because the concentrations of Ti and Zr in the extracts were below the estimated quantification limit. Gibbsite was consistently highly oversaturated in the extract while dawsonite was at or near equilibrium. This suggests that dawsonite might be a more suitable phase for the secondary phase reaction network

  11. Kinetic study on Iranian furfural extract hydrocracking

    Energy Technology Data Exchange (ETDEWEB)

    Zarkesh, J.; Akbarnejad, M. M. [NIOC Research Institute of Petroleum Industry, Tehran (Iran, Islamic Republic of); Khorasheh, F. [Sharif Univ. of Technology, Tehran (Iran, Islamic Republic of); Badakhshan, A. [Calgary Univ., AB (Canada)

    1998-05-01

    Upgrading heavy crude oil to light crude oil is one of the most important refining processes. Familiarity with the kinetics and related kinetic models is one of the important aspects of developing expertise in this field. This joint study between the NIOC Institute of Research of the Petroleum Industry and Sharif University was undertaken to determine the most appropriate upgrading process for Iranian heavy feed stock and to predict the conversion and product distribution in commercial hydrocracking units. The study involved the evaluation of stoichiometry of the hydrocracking process, focusing on the catalytic hydrocracking of furfural extract (a by-product of the lubricating oil plant) of the Tehran refinery. A pilot plant reactor was used. Good correspondence between model predictions and theoretical values was obtained.

  12. Novel Fluorinated Tensioactive Extractant Combined with Flotation for Decontamination of Extractant Residual during Solvent Extraction

    Science.gov (United States)

    Wu, Xue; Chang, Zhidong; Liu, Yao; Choe, Chol Ryong

    2017-12-01

    Solvent-extraction is widely used in chemical industry. Due to the amphiphilic character, a large amount of extractant remains in water phase, which causes not only loss of reagent, but also secondary contamination in water phase. Novel fluorinated extractants with ultra-low solubility in water were regarded as effective choice to reduce extractant loss in aqueous phase. However, trace amount of extractant still remained in water. Based on the high tensioactive aptitude of fluorinated solvent, flotation was applied to separate fluorinated extractant remaining in raffinate. According to the data of surface tension measurement, the surface tension of solution was obviously decreased with the addition of fluorinated extractant tris(2,2,3,3,4,4,5,5-octafluoropentyl) phosphate (FTAP). After flotation, the FTAP dissolved in water can be removed as much as 70%, which proved the feasibility of this key idea. The effects of operation time, gas velocity, pH and salinity of bulk solution on flotation performance were discussed. The optimum operating parameters were determined as gas velocity of 12ml/min, operating time of 15min, pH of 8.7, and NaCl volume concentration of 1.5%, respectively. Moreover, adsorption process of FTAP on bubble surface was simulated by ANSYS VOF model using SIMPLE algorithm. The dynamic mechanism of flotation was also theoretically investigated, which can be considered as supplement to the experimental results.

  13. TSCA Inventory Data Extraction Tool

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data extraction tool contains the non confidential identities of chemical substances submitted under the Toxic Substances Control Act (TSCA). TSCA was enacted...

  14. Combined keratoplasty and cataract extraction.

    Science.gov (United States)

    Demeler, U; Hinzpeter, E N

    1977-04-01

    A short film showing our technique of combined penetrating keratoplasty and intracapsular cataract extraction was shown, and the postoperative results in 72 eyes after an average of 3 years were reported.

  15. Extractive spectrophotometric determination of thorium

    International Nuclear Information System (INIS)

    Venkatesan, M.; Gopalakrishnan, V.; Ramanujam, A.; Nadkarni, M.N.

    1981-01-01

    An extractive spectrophotometric method has been standardized for the analysis of 0.2 to 1.6 milligrams of thorium present in nitric acid solutions. The method involves the extraction of thorium from nitric acid solutions into 0.5 M thenoyl trifluoro acetone (HTTA) in benzene and its direct estimation from the organic extract by spectrophotometry as Thoron colour complex. In this method, interference due to iron upto 5 milligrams can be suppressed by adding ascorbic acid in the ratio of 1:2 prior to HTTA extraction. Uranium(VI) does not interefere even when present in 2000 times the amount of thorium. Plutonium and cerium do not interfere at one milligram level whereas zirconium interferes in this method. The overall error variation and precision of this method has been determined to be +- 3.5%. (author)

  16. Extraction chromatography of fission products

    International Nuclear Information System (INIS)

    Bonnevie-Svendsen, M.; Goon, K.

    1978-01-01

    Various cases of using extraction chromatography during analysis of fission products are reviewed. The use of the extraction chromatography method is considered while analysing reprocessed products of nuclear fuel for quantitative radiochemical analysis and control of fission product and actinoide separation during extraction and their chemical state in production solutions. The method is used to obtain pure fractions of typical burnup monitors (neodymium, molybdenum, cerium, cesium, europium, lanthanides) during determination of nuclear fuel burnup degree. While studying the nature of nuclear reactions the method is used to separate quickly short-life isotopes, to purify β-radiator fractions before measuring their half-life periods, to enrich isotopes forming with low output during fission. Examples of using extraction chromatography are given to separate long half-life or stable fission products from spent solutions, to control environment object contamination

  17. Coil for LEAR extraction septum

    CERN Multimedia

    CERN PhotoLab

    1982-01-01

    Which way does the current flow ? This intriguing object is the coil for the LEAR extraction septum. There were two septa, first a thin one, then this one, not so thin, somewhat on the borderline between septum and bending magnet.

  18. Scenario Customization for Information Extraction

    National Research Council Canada - National Science Library

    Yangarber, Roman

    2001-01-01

    Information Extraction (IE) is an emerging NLP technology, whose function is to process unstructured, natural language text, to locate specific pieces of information, or facts, in the text, and to use these facts to fill a database...

  19. VT Mineral Resources - MRDS Extract

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) MRDSVT is an extract from the Mineral Resources Data System (MRDS) covering the State of Vermont only. MRDS database contains the records provided...

  20. Process for extracting oil shale

    Energy Technology Data Exchange (ETDEWEB)

    1920-08-22

    A process is described for recovering bituminous material from oil shale, characterized in that the oil shale is extracted with wood spirits oil (byproduct of woodspirit rectification), if necessary in admixture with other solvents in the cold or the hot.

  1. aqueous root extract on spermatogenesis

    African Journals Online (AJOL)

    Four groups were gavaged with the whole plant or root aqueous extract in low or high doses. The male ... motility and morphology as well as chromatin integrity were evaluated. Results: Serum ... Treatment of disease began long ago with the.

  2. Bio technologies in extractive metallurgy

    International Nuclear Information System (INIS)

    Morin, D.

    1995-01-01

    The bio technologies processes used (or used in the future) in extractive metallurgy are presented. The most advanced one is the degradation of the metals sulfides (bacteria catalyzing the sulfides oxidation of Au, Cu, U). Two other applications outside the extractive metallurgy are also described: metals fixation by living or dead organic matter and the biological destruction of organic reactants such as cyanides. (A.B.)

  3. Advanced integrated solvent extraction systems

    Energy Technology Data Exchange (ETDEWEB)

    Horwitz, E.P.; Dietz, M.L.; Leonard, R.A. [Argonne National Lab., IL (United States)

    1997-10-01

    Advanced integrated solvent extraction systems are a series of novel solvent extraction (SX) processes that will remove and recover all of the major radioisotopes from acidic-dissolved sludge or other acidic high-level wastes. The major focus of this effort during the last 2 years has been the development of a combined cesium-strontium extraction/recovery process, the Combined CSEX-SREX Process. The Combined CSEX-SREX Process relies on a mixture of a strontium-selective macrocyclic polyether and a novel cesium-selective extractant based on dibenzo 18-crown-6. The process offers several potential advantages over possible alternatives in a chemical processing scheme for high-level waste treatment. First, if the process is applied as the first step in chemical pretreatment, the radiation level for all subsequent processing steps (e.g., transuranic extraction/recovery, or TRUEX) will be significantly reduced. Thus, less costly shielding would be required. The second advantage of the Combined CSEX-SREX Process is that the recovered Cs-Sr fraction is non-transuranic, and therefore will decay to low-level waste after only a few hundred years. Finally, combining individual processes into a single process will reduce the amount of equipment required to pretreat the waste and therefore reduce the size and cost of the waste processing facility. In an ongoing collaboration with Lockheed Martin Idaho Technology Company (LMITCO), the authors have successfully tested various segments of the Advanced Integrated Solvent Extraction Systems. Eichrom Industries, Inc. (Darien, IL) synthesizes and markets the Sr extractant and can supply the Cs extractant on a limited basis. Plans are under way to perform a test of the Combined CSEX-SREX Process with real waste at LMITCO in the near future.

  4. Uranium refining by solvent extraction

    International Nuclear Information System (INIS)

    Kraikaew, J.; Srinuttrakul, W.

    2014-01-01

    The solvent extraction process to produce higher purity uranium from yellowcake was studied in laboratory scale. Yellowcake, which the uranium purity is around 70% and the main impurity is thorium, was obtained from monazite processing pilot plant of Rare Earth Research and Development Center in Thailand. For uranium re-extraction process, the extractant chosen was Tributylphosphate (TBP) in kerosene. It was found that the optimum concentration of TBP was 10% in kerosene and the optimum nitric acid concentration in uranyl nitrate feed solution was 4 N. An increase in concentrations of uranium and thorium in feed solution resulted in a decrease in the distribution of both components in the extractant. However, the distribution of uranium into the extractant was found to be more than that of thorium. The equilibration study of the extraction system, UO_2(NO_3)/4N HNO_3 – 10%TBP/Kerosene, was also investigated. Two extraction stages were calculated graphically from 100,000 ppm uranium concentration in feed solution input with 90% extraction efficiency and the flow ratio of aqueous phase to organic phase was adjusted to 1.0. For thorium impurity scrubbing process, 10% TBP in kerosene was loaded with uranium and minor thorium from uranyl nitrate solution prepared from yellowcake and was scrubbed with different low concentration nitric acid. The results showed that at nitric acid normality was lower than 1 N, uranium distributed well to aqueous phase. As conclusion, optimum nitric acid concentration for scrubbing process should not less than 1 N and diluted nitric acid or de-ionized water should be applied to strip uranium from organic phase in the final refining process. (author)

  5. Extracting useful information from images

    DEFF Research Database (Denmark)

    Kucheryavskiy, Sergey

    2011-01-01

    The paper presents an overview of methods for extracting useful information from digital images. It covers various approaches that utilized different properties of images, like intensity distribution, spatial frequencies content and several others. A few case studies including isotropic and heter......The paper presents an overview of methods for extracting useful information from digital images. It covers various approaches that utilized different properties of images, like intensity distribution, spatial frequencies content and several others. A few case studies including isotropic...

  6. Extractive Summarisation of Medical Documents

    OpenAIRE

    Abeed Sarker; Diego Molla; Cecile Paris

    2012-01-01

    Background Evidence Based Medicine (EBM) practice requires practitioners to extract evidence from published medical research when answering clinical queries. Due to the time-consuming nature of this practice, there is a strong motivation for systems that can automatically summarise medical documents and help practitioners find relevant information. Aim The aim of this work is to propose an automatic query-focused, extractive summarisation approach that selects informative sentences from medic...

  7. Unconventional oil and gas extraction and animal health.

    Science.gov (United States)

    Bamberger, M; Oswald, R E

    2014-08-01

    The extraction of hydrocarbons from shale formations using horizontal drilling with high volume hydraulic fracturing (unconventional shale gas and tight oil extraction), while derived from methods that have been used for decades, is a relatively new innovation that was introduced first in the United States and has more recently spread worldwide. Although this has led to the availability of new sources of fossil fuels for domestic consumption and export, important issues have been raised concerning the safety of the process relative to public health, animal health, and our food supply. Because of the multiple toxicants used and generated, and because of the complexity of the drilling, hydraulic fracturing, and completion processes including associated infrastructure such as pipelines, compressor stations and processing plants, impacts on the health of humans and animals are difficult to assess definitively. We discuss here findings concerning the safety of unconventional oil and gas extraction from the perspectives of public health, veterinary medicine, and food safety.

  8. Scale-up of mixer-settler for uranium extraction

    International Nuclear Information System (INIS)

    Santana, A.O. de.

    1990-05-01

    The aim of this work was to obtain scale-up relations for a box type mixer-settler used in uranium extraction process for chloridric leaches. Three box type units with different sizes and with the same geometry were used for scale-up of the mixer. The correlation between extraction rate and specific power input, D/T ratio (stirrer diameter/mixer length) and residence time were experimentally obtained. The results showed that the extraction increases with power input for a constant value of D/T equal to 1/3, remaining however independent from mixer sizes for a specific value of power input. This behavior was observed for power input values ranging from 100 to 750 w/m 9 . (author). 23 refs, 22 figs, 23 tabs

  9. Extraction of Aromatics from Heavy Naphtha Using Different Solvents

    International Nuclear Information System (INIS)

    EI-Bassuoni, A.A.; Esmael, K.K.

    2004-01-01

    Aromatic hydrocarbons are very important to the petrochemical industry. Among these are benzene, toluene and xylene (BTX), which are basic raw materials for the production of a number of important petrochemicals. There are many processes used to separate aromatic from non aromatic such as fractionation, azeotropic distillation and liquid I liquid extraction, etc. Liquid - liquid extraction is unique, efficiently used for heat sensitive, close boiling components and for separation of components not possible by other unit operations and it could be done at ambient temperature makes it more energy efficient. The choice of solvent depends on the properties and boiling range of the feedstock. Through the years, a lot of selective solvents has been proposed and selected for the physical separation of aromatics in liquid liquid extraction. Among the selection criteria are the stability,. chemical compatibility, availability, environmental hazards and price of the solvent. But the basic solvent properties that make it efficient are selectivity and capacity

  10. A multiplicity logic unit

    International Nuclear Information System (INIS)

    Bialkowski, J.; Moszynski, M.; Zagorski, A.

    1981-01-01

    The logic diagram principle of operation and some details of the design of the multiplicity logic unit are presented. This unit was specially designed to fulfil the requirements of a multidetector arrangement for gamma-ray multiplicity measurements. The unit is equipped with 16 inputs controlled by a common coincidence gate. It delivers a linear output pulse with the height proportional to the multiplicity of coincidences and logic pulses corresponding to 0, 1, ... up to >= 5-fold coincidences. These last outputs are used to steer the routing unit working with the multichannel analyser. (orig.)

  11. ENERGY STAR Unit Reports

    Data.gov (United States)

    Department of Housing and Urban Development — These quarterly Federal Fiscal Year performance reports track the ENERGY STAR qualified HOME units that Participating Jurisdictions record in HUD's Integrated...

  12. Phoenix I energy extraction experiment

    International Nuclear Information System (INIS)

    Hoffman, J.M.; Patterson, E.L.; Tisone, G.C.; Moreno, J.B.

    1980-07-01

    Energy extraction experiments are reported for the Phoenix I amplifier driven by a discharge-initiated oscillator-preamplifier system operating on mixtures of either SF 6 -HI or SF 6 -C 2 H 6 and an electron-beam-initiated intermediate amplifer (lambda-3) fueled with H 2 and F 2 mixtures. When the oscillator-preamplifier system operated with mixtures of SF 6 -HI the input spectrum to the Phoenix I amplifier contained approx. 28 P-branch vibrational-rotational lines which were almost identical to the input spectrum from the H 2 -F 2 fueled oscillator. In this case the energy extraction measurements were essentially the same as the results obtained with the spectrum produced using H 2 and F 2 mixtures. For an input intensity of 10 7 W/cm 2 , 170 J were extracted from the amplifier. With the SF 6 -C 2 H 6 spectrum, extraction was only obtained from the first three excited vibrational levels. This result indicates that most of the energy in the amplifier could be extracted on the first three excited vibrational levels. It is shown that the extraction results can be fit with a simple two level model. The radius of curvature of the beam was estimated using a lateral shearing interferometer. It was found that the Phoenix I amplifier altered the radius of curvature

  13. Screening for antibiofilm and antioxidant potential of turmeric (Curcuma longa) extracts.

    Science.gov (United States)

    Hayat, Sumreen; Sabri, Anjum Nasim

    2016-07-01

    The antibiofilm and antioxidant activities associated with turmeric were the main focus of the study. Antibacterial activity was explored against bacteria isolated from dental plaques and dental unit water lines exhibiting resistance against antibiotics and biocides respectively. This study provides a comparison of the natural plant extract against synthetic mouthwash, chemicals and commonly prescribed antibiotics. Methanol extract was more effective as compared to other extracts. Minimum inhibitory concentrations (MIC) ranged from 2.5-10mg/ml. Time based killing kinetic assay showed a significant reduction of bacterial load with increasing concentration of turmeric. Micro titer plate assay indicated significant inhibition of biofilm formation in cells treated with turmeric extract. Phytochemical screening of plant extracts showed the presence of vital secondary metabolites. Flavonoid content and total phenolic content varied among extracts, phenolic content for methanolic extract was 61.669 mg GAE/ gm dry extract and flavonoid content was 3.119mg quercitin/gm dry extract. The values of ferric reducing power were in the range of 5.55- 15.55 mmol of FeSO4 equivalent/ liter of the extract. Antioxidant activities and total phenolic content of the turmeric extracts had significant positive correlation. On the basis of these results turmeric may confidently be recommended as natural antibiofilm and antioxidant agent.

  14. Process optimisation of microwave-assisted extraction of peony ( Paeonia suffruticosa Andr .) seed oil using hexane-ethanol mixture and its characterisation

    Science.gov (United States)

    Xiaoli Sun; Wengang Li; Jian Li; Yuangang Zu; Chung-Yun Hse; Jiulong Xie; Xiuhua Zhao

    2016-01-01

    Ethanol and hexane mixture agent microwave-assisted extraction (MAE) method was conducted to extract peony (Paeonia suffruticosa Andr.) seed oil (PSO). The aim of the study was to optimise the extraction for both yield and energy consumption in mixture agent MAE. The highest oil yield (34.49%) and lowest unit energy consumption (14 125.4 J g -1)...

  15. The method for simultaneous extraction and back extraction in liquid three-phase system and equipment for simultaneous extraction and back extraction in liquid three-phase system

    International Nuclear Information System (INIS)

    Palyska, W.; Chmielewski, A.G.

    1992-01-01

    The method for simultaneous extraction and back extraction in liquid three-phase system has been worked out. The equipment designed for that process has been also subject of the patent. The interesting component is extracted first to intermediate phase consists of magnetic solvent keeping two extracting phases separately. The intermediate magnetic liquid has been kept in its position using a stable magnet maintained on the surface of the extraction vessel. Then the component pass from intermediate phase to the third phase as a result of back extraction. Mixing in the extraction and back extraction zones is organized by means of rotating shaft going along the whole apparatus. The extraction and back extraction processes occur simultaneously as a result of continuous flow of solvent in their zones. The single extraction back extraction facilities can be joined in larger batteries. 3 figs

  16. Impact of Strontium Nitrate and Sodium Permanganate Addition on Solid-Liquid Separation of SRS High Level Waste

    International Nuclear Information System (INIS)

    Poirier, M.R.

    2002-01-01

    As a pretreatment step for the caustic side solvent extraction (CSSX) flowsheet, the process contacts the incoming salt solution containing entrained sludge with monosodium titanate (MST) to adsorb strontium and actinides. An operation filters the resulting slurry to remove the sludge and MST. Previous work for the River Protection Program at Hanford suggests that addition of strontium nitrate and sodium permanganate for strontium and actinide removal, rather than MST, improves the filtration rate for comparable waste streams

  17. 31 CFR 515.321 - United States; continental United States.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 515.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof, including the Trust Territory of...

  18. 31 CFR 500.321 - United States; continental United States.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 500.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof, including U.S. trust territories...

  19. 31 CFR 535.321 - United States; continental United States.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 535.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof including the Trust Territory of...

  20. What Constitutes a Unit of Analysis in Language?

    Directory of Open Access Journals (Sweden)

    Danielsson, Pernilla

    2007-01-01

    Full Text Available Over the last decade, the study of multi-word units has become increasingly popular and now these units seem to have reached a status where they cannot be ignored. This paper should be seen as a recapituation of the discussion around multi-word units, especially focusing on corpus evidence of such units and what is perceived to be relevant findings. An unsupervised method for extracting multi-word units from corpora is presented and the findings examined. However, rather than evaluating the results, this article will raise the question of what constitutes a 'good' multi-word unit? The article does not claim to give any conclusive answers but perhaps instead posing a few relevant questions.

  1. Establishment of a New Drug Code for Marihuana Extract. Final rule.

    Science.gov (United States)

    2016-12-14

    The Drug Enforcement Administration is creating a new Administration Controlled Substances Code Number for "Marihuana Extract." This code number will allow DEA and DEA-registered entities to track quantities of this material separately from quantities of marihuana. This, in turn, will aid in complying with relevant treaty provisions. Under international drug control treaties administered by the United Nations, some differences exist between the regulatory controls pertaining to marihuana extract versus those for marihuana and tetrahydrocannabinols. The DEA has previously established separate code numbers for marihuana and for tetrahydrocannabinols, but not for marihuana extract. To better track these materials and comply with treaty provisions, DEA is creating a separate code number for marihuana extract with the following definition: "Meaning an extract containing one or more cannabinoids that has been derived from any plant of the genus Cannabis, other than the separated resin (whether crude or purified) obtained from the plant." Extracts of marihuana will continue to be treated as Schedule I controlled substances.

  2. Neighbors United for Health

    Science.gov (United States)

    Westhoff, Wayne W.; Corvin, Jaime; Virella, Irmarie

    2009-01-01

    Modeled upon the ecclesiastic community group concept of Latin America to unite and strengthen the bond between the Church and neighborhoods, a community-based organization created Vecinos Unidos por la Salud (Neighbors United for Health) to bring health messages into urban Latino neighborhoods. The model is based on five tenants, and incorporates…

  3. Smart Rocking Armour Units

    NARCIS (Netherlands)

    Hofland, B.; Arefin, Syed Shamsil; van der Lem, Cock; van gent, Marcel

    2018-01-01

    This paper describes a method to measure the rocking motion of lab-scale armour units. Sensors as found in mobile phones are used. These sensors, data-storage and battery are all embedded in the model units, such that they can be applied without wires attached to them. The technique is applied to

  4. METRIC context unit architecture

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, R.O.

    1988-01-01

    METRIC is an architecture for a simple but powerful Reduced Instruction Set Computer (RISC). Its speed comes from the simultaneous processing of several instruction streams, with instructions from the various streams being dispatched into METRIC's execution pipeline as they become available for execution. The pipeline is thus kept full, with a mix of instructions for several contexts in execution at the same time. True parallel programming is supported within a single execution unit, the METRIC Context Unit. METRIC's architecture provides for expansion through the addition of multiple Context Units and of specialized Functional Units. The architecture thus spans a range of size and performance from a single-chip microcomputer up through large and powerful multiprocessors. This research concentrates on the specification of the METRIC Context Unit at the architectural level. Performance tradeoffs made during METRIC's design are discussed, and projections of METRIC's performance are made based on simulation studies.

  5. Extraction and characterization of galactomannan extracted from Prosopis juliflora seeds

    International Nuclear Information System (INIS)

    Rodrigues, Delane da C.; Cunha, Arcelina P.; Oliveira, Williara Q. de; Gallao, Maria Izabel; Azeredo, Henriette M. C de

    2015-01-01

    Different seeds are rich in polysaccharides, which are widely used in research and in industry. The objective was to extract galactomannan from mesquite seeds (Prosopis juliflora) and evaluate their chemical properties for future application in edible films. To test the feasibility of using the polysaccharide, the yield was obtained and the material analyzed by Thermal Analysis (TGA-Thermogravimetric Analysis and Calorimetry Differential Scanning-DSC), Spectroscopy Infrared Region Fourier Transform (FTIR) and Nuclear Magnetic Resonance (NMR). According to the results, the galactomannan was equivalent with the polysaccharides extracted from other sources except for the low yield (6.6%). (author)

  6. Treatment of wastewater containing dissolved metals by extraction-flotation

    International Nuclear Information System (INIS)

    Puget, Flavia Pereira

    2002-02-01

    In this work an alternative process for treating a wastewater containing dissolved metals (uranium and zirconium) is considered. In order to develop this work, a continuous separation unit, characterized by the association of solvent extraction and liquid-liquid flotation is used. Alamina 336 (a mixture of tri-octyl and tri-decyl amines) is used as extractant in the the extraction process, carried out inward the ejector. The splitting of the amine-water emulsion formed is carried out in a continuously operated flotation column (of approximately 2.5 L volume). The solvent extraction results showed that it is possible to reach an efficiency of about 95% for the uranium and zirconium extraction, for a metal in the feed concentration of 10 ppm and for a Q fa /Q fo ratio around 200. An efficiency of about 80% is reached in the flotation column when the liquid flowrate is equal 0.05 Lmin -1 and the air flowrate is equal 3.3 Lmin -1 . (author)

  7. Valorization of Tomato Processing Waste for Lycopene Extraction

    Directory of Open Access Journals (Sweden)

    Rim Driouich

    2016-11-01

    Full Text Available Lycopene is one of the most powerful antioxidants and singlet oxygen quenching agents. It has been found to be of great medical importance with various anti cancer effects, cardiovascular diseases effective agent and with its ability to be an important carotenoid in preventive medicine. In Tunisia, we note a real consumption of tomato paste. With 28 production units for double and triple concentrated tomato, noting a significant production of waste (approximately 30000 Tonne/year consisting of skins pulp and seeds, which could be an important source of lycopene. Our study is concerned with three solid-phase extraction process: assisted by ultrasonic, by microwave and by homogenizer heating at moderate temperature. Their efficiency for the extraction of lycopene contained in the tomato waste was elaborated. The effect of the main process variables (including solvent polarity, solid-to-liquid ratio, temperature and time on lycopene recovery have been investigated. The yield of the isolated lycopene was determined using UV-Visible spectrophotometry and UPLC-DAD quantification methods. Lycopene-rich extract was obtained from the dried and milled tomatoes waste using ethanol as a food grade extraction solvent and employing microwave assisted extraction process. The optimum conditions were 30 min total extraction time at 50°C temperature and 1bar pressure. The degradation of extracted lycopene through air oxidation and day light effect were also tested. Lycopene is stable when mixed with olive oil as a natural antioxidant. Up to 80% of lycopene degradated when exposed for one month to day light at 25°C.

  8. Stand tests of the grader unit AKD-2

    Energy Technology Data Exchange (ETDEWEB)

    Kocheskhov, S.M.; Bagley, A.V.; Shalkov, A.V.

    1982-01-01

    Results are presented of stand tests of a static operating grader designed for unmanned extraction of deep beds with programmed control of the unit AKD-2 according to hypsometry of the seam occurrence. Malfunctions in a number of grader assemblies are revealed and eliminated. Parameters are defined which characterize the kinematics and dynamics of the grader mechanism.

  9. NMR investigation of coal extracts

    Energy Technology Data Exchange (ETDEWEB)

    Lang, I; Sebor, G [Ceskoslovenska Akademie Ved, Prague. Hornicky Ustav; Sebor, G Jr; Hajek, M; Mostecky, J [Vysoka Skola Chemicko-Technologicka, Prague (Czechoslovakia)

    1978-07-01

    Proton NMR spectroscopy was used for the evaluation of 10% coal extract solutions in deuterated pyridine. Four types of Czechoslovak coal were analyzed. Agreement was found between the aromaticity of coal extracts calculated from /sup 1/H NMR data using Brown's method and Ladner's and Williams' method and the characterization of an average molecule of the coal extract by the number of non-bridge carbon atoms of aromatic rings, by the overall number of aromatic ring carbon atoms and the number of aromatic rings, determined by the Williams and Ferris methods. The methods for calculating carbon distribution from /sup 1/H NMR data, however, contain some constants theoretically estimated or experimentally found using the method which still remain to be verified.

  10. Indium recovery by solvent extraction

    International Nuclear Information System (INIS)

    Fortes, Marilia Camargos Botelho

    1999-04-01

    Indium has been recovered as a byproduct from residues generated from the sulfuric acid leaching circuits in mineral plants for zinc recovery. Once its recovery comes from the slags of other metals recovery, it is necessary to separate it from the other elements which usually are present in high concentrations. Many works have been approaching this separation and indicate the solvent extraction process as the main technique used. In Brazilian case, indium recovery depends on the knowledge of this technique and its development. This paper describes the solvent extraction knowledge for the indium recovery from aqueous solutions generated in mineral plants. The results for determination of the best experimental conditions to obtain a high indium concentration solution and minimum iron poisoning by solvent extraction with di (2-ethylhexyl)-phosphoric acid (D2EHPA) solubilized in isoparafin and exxsol has been presented. (author)

  11. Salt effects in electromembrane extraction

    DEFF Research Database (Denmark)

    Seip, Knut Fredrik; Jensen, Henrik; Kieu, Thanh Elisabeth

    2014-01-01

    Electromembrane extraction (EME) was performed on samples containing substantial amounts of NaCl to investigate how the presence of salts affected the recovery, repeatability, and membrane current in the extraction system. A group of 17 non-polar basic drugs with various physical chemical...... this loss and the physical chemical properties of these substances was seen. The recovery loss was hypothesized to be caused by ion pairing in the SLM, and a mathematical model for the extraction recovery in the presence of salts was made according to the experimental observations. Some variations...... to the EME system reduced this recovery loss, such as changing the SLM solvent from NPOE to 6-undecanone, or by using a different EME setup with more favorable volume ratios. This was in line with the ion pairing hypothesis and the mathematical model. This thorough investigation of how salts affect EME...

  12. Solvent extraction: the coordination chemistry behind extractive metallurgy.

    Science.gov (United States)

    Wilson, A Matthew; Bailey, Phillip J; Tasker, Peter A; Turkington, Jennifer R; Grant, Richard A; Love, Jason B

    2014-01-07

    The modes of action of the commercial solvent extractants used in extractive hydrometallurgy are classified according to whether the recovery process involves the transport of metal cations, M(n+), metalate anions, MXx(n-), or metal salts, MXx into a water-immiscible solvent. Well-established principles of coordination chemistry provide an explanation for the remarkable strengths and selectivities shown by most of these extractants. Reagents which achieve high selectivity when transporting metal cations or metal salts into a water-immiscible solvent usually operate in the inner coordination sphere of the metal and provide donor atom types or dispositions which favour the formation of particularly stable neutral complexes that have high solubility in the hydrocarbons commonly used in recovery processes. In the extraction of metalates, the structures of the neutral assemblies formed in the water-immiscible phase are usually not well defined and the cationic reagents can be assumed to operate in the outer coordination spheres. The formation of secondary bonds in the outer sphere using, for example, electrostatic or H-bonding interactions are favoured by the low polarity of the water-immiscible solvents.

  13. Decision unit program

    International Nuclear Information System (INIS)

    Madjar, N.; Pastor, C.; Chambon, B.; Drain, D.; Giorni, A.; Dauchy, A.

    1981-01-01

    A decision unit has been built to simplify the electronic logic set-up in multi-detectors experiments. This unit, designed with fast memories used as decision making tables, replaces conventional logic modules. Nine inputs are provided for receiving the fast detector signals (charged particles, gammas, neutrons, ...). Fifteen independent outputs allow the identification of the choosen events among the 2 9 possible events. A CAMAC interface between the unit and the computer, or a manual control auxiliary module, is used to load, in the memory, the pattern of the choosen events [fr

  14. Smart Rocking Armour Units

    OpenAIRE

    Hofland, B.; Arefin, Syed Shamsil; van der Lem, Cock; van gent, Marcel

    2018-01-01

    This paper describes a method to measure the rocking motion of lab-scale armour units. Sensors as found in mobile phones are used. These sensors, data-storage and battery are all embedded in the model units, such that they can be applied without wires attached to them. The technique is applied to double-layer units in order to compare the results to the existing knowledge for this type of armour layers. In contrast to previous research, the gyroscope reading is used to determine the (rocking)...

  15. Allocating multiple units

    DEFF Research Database (Denmark)

    Tranæs, Torben; Krishna, Kala

    2002-01-01

    This paper studies the allocation and rent distribution in multi-unit, combinatorial-bid auctions under complete information. We focus on the natural multi-unit analogue of the first-price auction, where buyers bid total payments, pay their bids, and where the seller allocates goods to maximize his...... auction, which is the multi unit analogue of a second-price auction. Furthermore, we characterize these equilibria when valuations take a number of different forms: diminishing marginal valuations, increasing average valuations, and marginal valuations with single turning points...

  16. Ocean Thermal Extractable Energy Visualization

    Energy Technology Data Exchange (ETDEWEB)

    Ascari, Matthew [Lockheed Martin Corporation, Bethesda, MD (United States)

    2012-10-28

    The Ocean Thermal Extractable Energy Visualization (OTEEV) project focuses on assessing the Maximum Practicably Extractable Energy (MPEE) from the world’s ocean thermal resources. MPEE is defined as being sustainable and technically feasible, given today’s state-of-the-art ocean energy technology. Under this project the OTEEV team developed a comprehensive Geospatial Information System (GIS) dataset and software tool, and used the tool to provide a meaningful assessment of MPEE from the global and domestic U.S. ocean thermal resources.

  17. Photochemical separation and extraction device

    International Nuclear Information System (INIS)

    Wada, Yukio; Morimoto, Kyoichi.

    1998-01-01

    The present invention concerns a device for separating neptunium and plutonium from highly radioactive liquid wastes, in which valance control by irradiation of UV rays and extraction operation by using an organic solvent can be conducted simultaneously in the same reaction vessel. Namely, a step of irradiating UV rays to the liquid in the reaction vessel to control the valence of predetermined materials and a step of separating the materials by conducting solvent-extraction while stirring with a solvent are conducted simultaneously or successively. Then, facilities for the separation method can be reduced and the operation steps can be simplified. (N.H.)

  18. 75 FR 81949 - Disclosure of Cochineal Extract and Carmine in the Labeling of Wines, Distilled Spirits, and Malt...

    Science.gov (United States)

    2010-12-29

    ... Extract and Carmine in the Labeling of Wines, Distilled Spirits, and Malt Beverages; Comment Period... Extract and Carmine in the Labeling of Wines, Distilled Spirits, and Malt Beverages, a notice of proposed... attorney Lynne J. Omlie on behalf of the Distilled Spirits Council of the United States, Inc. (DISCUS), a...

  19. 78 FR 50437 - U.S. Extractive Industries Transparency Initiative Multi-Stakeholder Group (USEITI MSG) Advisory...

    Science.gov (United States)

    2013-08-19

    ... DEPARTMENT OF THE INTERIOR Office of the Secretary [Docket No. ONRR-2012-0003; DS63600000 DR2PS0000.PX8000 134D0102R2] U.S. Extractive Industries Transparency Initiative Multi- Stakeholder Group...: This notice announces the next three meetings of the United States Extractive Industries Transparency...

  20. 78 FR 60304 - U.S. Extractive Industries Transparency Initiative Multi-Stakeholder Group (USEITI MSG) Advisory...

    Science.gov (United States)

    2013-10-01

    ... DEPARTMENT OF THE INTERIOR Office of the Secretary [Docket No. ONRR-2012-0003; DS63600000 DR2PS0000.PX8000 134D0102R2] U.S. Extractive Industries Transparency Initiative Multi- Stakeholder Group...: This notice announces the meeting date change of the United States Extractive Industries Transparency...

  1. 78 FR 18624 - U.S. Extractive Industries Transparency Initiative Multi-Stakeholder Group (USEITI MSG) Advisory...

    Science.gov (United States)

    2013-03-27

    ... DEPARTMENT OF THE INTERIOR Office of the Secretary [Docket No. ONRR-2012-0003] U.S. Extractive Industries Transparency Initiative Multi- Stakeholder Group (USEITI MSG) Advisory Committee AGENCY: Policy..., teleconference and the May 1-2, 2013, meeting of the United States Extractive Industries Transparency Initiative...

  2. 77 FR 51041 - 30-Day Extension of Call for Nominations for the U.S. Extractive Industries Transparency...

    Science.gov (United States)

    2012-08-23

    ... DEPARTMENT OF THE INTERIOR Office of the Secretary [Docket No. ONRR-2012-0003] 30-Day Extension of Call for Nominations for the U.S. Extractive Industries Transparency Initiative Advisory Committee... the United States Extractive Industries Transparency Initiative (USEITI) Multi- Stakeholder Group (MSG...

  3. 11. Russian Conference on Extraction. Abstracts

    International Nuclear Information System (INIS)

    Zolotov, Yu.A.

    1998-01-01

    Results of fundamental and applied investigations in the region of chemistry of extraction, technology and analytical chemistry are presented. Modern state of theoretical and experimental investigations in the region of thermodynamics and kinetics of extraction by organic phosphorus compounds, organic nitrogen compounds and their mixtures are described. Date on mass exchange, extraction process simulation, extraction apparatuses are given

  4. Tax Unit Boundaries

    Data.gov (United States)

    Kansas Data Access and Support Center — The Statewide GIS Tax Unit boundary file was created through a collaborative partnership between the State of Kansas Department of Revenue Property Valuation...

  5. Insects: An Interdisciplinary Unit

    Science.gov (United States)

    Leger, Heather

    2007-01-01

    The author talks about an interdisciplinary unit on insects, and presents activities that can help students practice communication skills (interpersonal, interpretive, and presentational) and learn about insects with hands-on activities.

  6. UnitedHealth Group

    Science.gov (United States)

    UnitedHealth Group provides accessible and affordable services, improved quality of care, coordinated health care efforts, and a supportive environment for shared decision making between patients and their physicians.

  7. Operable Unit Boundaries

    Data.gov (United States)

    U.S. Environmental Protection Agency — This dataset consists of operable unit data from multiple Superfund sites in U.S. EPA Region 8. These data were acquired from multiple sources at different times and...

  8. Flywheel and power unit

    Energy Technology Data Exchange (ETDEWEB)

    Seeley, R.W.

    1992-10-28

    A power unit, e.g. for an electrically driven vehicle, incorporates a flywheel for storing kinetic energy and a battery for storing electrical energy. The battery is incorporated as a substantial part of the rotating mass of the flywheel. Preferably the unit further includes an electrical machine being a motor or generator or machine operable either as a motor or a generator for transferring energy between the battery and the flywheel and/or for the input or output of rotary energy therefrom or thereto. The motor may be used for powering the flywheel and may also operate in a regenerative mode for recharging the unit on de-acceleration of the vehicle. The unit of the invention may also be utilized as an electrical stored power source, e.g. wind or water driven. (author)

  9. Does size matter? Animal units and animal unit months

    Science.gov (United States)

    Lamar Smith; Joe Hicks; Scott Lusk; Mike Hemmovich; Shane Green; Sarah McCord; Mike Pellant; John Mitchell; Judith Dyess; Jim Sprinkle; Amanda Gearhart; Sherm Karl; Mike Hannemann; Ken Spaeth; Jason Karl; Matt Reeves; Dave Pyke; Jordan Spaak; Andrew Brischke; Del Despain; Matt Phillippi; Dave Weixelmann; Alan Bass; Jessie Page; Lori Metz; David Toledo; Emily Kachergis

    2017-01-01

    The concepts of animal units, animal unit months, and animal unit equivalents have long been used as standards for range management planning, estimating stocking rates, reporting actual use, assessing grazing fees, ranch appraisal, and other purposes. Increasing size of cattle on rangelands has led some to suggest that the definition of animal units and animal unit...

  10. Extraction of copper zinc and iron from hydrochloric acid solutions by means of different extractants

    Energy Technology Data Exchange (ETDEWEB)

    Zhivkova, Svetlana [Institute of Chemical Engineering - Bulgarian Academy of Sciences, Sofia (Bulgaria)

    2011-07-01

    The extraction of copper, zinc and iron from hydrochloric acid solutions has been studied. The experiments have been carried out using various solvents, involving different extraction mechanisms – solvating, anion-exchange, cation-exchange, bifunctional . Mixtures of these extractants have been also used. The extraction properties of these extractant mixtures toward copper, zinc and iron, the effect of used modifiers and diluents have been also investigated. Key words: Copper, Zinc, Iron, Extraction, Extractant, Modifier, Diluent.

  11. Analytical Methods for Cs-137 and Other Radionuclides in Solvent Samples

    International Nuclear Information System (INIS)

    Pennebaker, F.M.

    2002-01-01

    Accurate characterization of individual waste components is critical to ensure design and operation of effective treatment processes and compliance with waste acceptance criteria. Current elemental analysis of organic matrices consists of conversion of the organic sample to aqueous by digesting the sample, which is inadequate in many cases. Direct analysis of the organic would increase sensitivity and decrease contamination and analysis time. For this project, we evaluated an Aridus membrane-desolvation sample introduction system for the direct analysis of organic solvents by Inductively Coupled Plasma - Mass Spectrometry (ICP-MS). The desolvator-ICP-MS successfully analyzed solvent from the caustic-side solvent extraction (CSSX) process and tri-butyl phosphate (TBP) organic tank waste from F-canyon for a variety of elements. Detection limits for most elements were determined in the part per trillion (ppt) range. This technology should increase accuracy in support of SRTC activities involving CSSX and other site processes involving organic compounds

  12. A method for real-time implementation of HOG feature extraction

    Science.gov (United States)

    Luo, Hai-bo; Yu, Xin-rong; Liu, Hong-mei; Ding, Qing-hai

    2011-08-01

    Histogram of oriented gradient (HOG) is an efficient feature extraction scheme, and HOG descriptors are feature descriptors which is widely used in computer vision and image processing for the purpose of biometrics, target tracking, automatic target detection(ATD) and automatic target recognition(ATR) etc. However, computation of HOG feature extraction is unsuitable for hardware implementation since it includes complicated operations. In this paper, the optimal design method and theory frame for real-time HOG feature extraction based on FPGA were proposed. The main principle is as follows: firstly, the parallel gradient computing unit circuit based on parallel pipeline structure was designed. Secondly, the calculation of arctangent and square root operation was simplified. Finally, a histogram generator based on parallel pipeline structure was designed to calculate the histogram of each sub-region. Experimental results showed that the HOG extraction can be implemented in a pixel period by these computing units.

  13. UniTed

    OpenAIRE

    Harma, Eero

    2010-01-01

    UniTed on Teddy boy- tyylistä inspiroitunut kevät/kesä mallisto naisille.Mallistossa yhdistyy perinteinen teddy boy- vaatetus ja klassinen feminiinisyys, sekä menneisyys ja nykyisyys. Suunnittelun lähtökohtia olivat naisellisuus, tyylikkyys ja pyrkimys luoda nykyaikaista suunnittelua menneisyydestä lainaillen. United is a teddy boy- style inspired spring/summer collection for women. The collection combines traditional Teddy boy style with classical feminity and past with the present. The b...

  14. Noble metal extraction and sorption concentrating

    International Nuclear Information System (INIS)

    Petrukhin, O.M.; Malofeeva, G.I.

    1985-01-01

    Works performed in the USSR Academy of Sciences GEOCHI laboratory of extraction methods and devoted to selectivity problems of extraction and sorption methods of platinum metal, cadmium and indium concentrating in analytical chemistry are discussed. On choosing complexino. reagent main attention is paid to the selectivity variation based on different stability of metal complexes. Platinum metals are extracted in the form of ion associates when usinq hard, mainly oxyqen-containing, extractants. Coordination-solvated metal complexes are extracted white usinq extractants containing sulfur, trivalent phosphorus and aromatic nitroqen as donor anions. Selectivity is maximum for sulfur- and nitroren-containinq extractants and sorbents. In case of the group extraction of platinum metals sorption is preferable and in case of selective extraction of individual metals, especially, in case of need of relative concentratinq extraction is preferable

  15. Freestanding midwifery unit versus obstetric unit

    DEFF Research Database (Denmark)

    Overgaard, Charlotte; Møller, Anna Margrethe; Fenger-Grøn, Morten

    2011-01-01

    low-risk women intending FMU birth and a matched control group of 839 low-risk women intending OU birth were included at the start of care in labour. OU women were individually chosen to match selected obstetric/socio-economic characteristics of FMU women. Analysis was by intention to treat. Main......Objective To compare perinatal and maternal morbidity and birth interventions in low-risk women giving birth in two freestanding midwifery units (FMUs) and two obstetric units (OUs). Design A cohort study with a matched control group. Setting The region of North Jutland, Denmark. Participants 839...... women were significantly less likely to experience an abnormal fetal heart rate (RR: 0.3, 95% CI 0.2 to 0.5), fetal–pelvic complications (0.2, 0.05 to 0.6), shoulder dystocia (0.3, 0.1 to 0.9), occipital–posterior presentation (0.5, 0.3 to 0.9) and postpartum haemorrhage >500 ml (0.4, 0.3 to 0...

  16. Uranium extraction from underground deposits

    International Nuclear Information System (INIS)

    Wolfe, C.R.

    1982-01-01

    Uranium is extracted from underground deposits by passing an aqueous oxidizing solution of carbon dioxide over the ore in the presence of calcium ions. Complex uranium carbonate or bicarbonate ions are formed which enter the solution. The solution is forced to the surface and the uranium removed from it

  17. Feature extraction using fractal codes

    NARCIS (Netherlands)

    B.A.M. Ben Schouten; Paul M. de Zeeuw

    1999-01-01

    Fast and successful searching for an object in a multimedia database is a highly desirable functionality. Several approaches to content based retrieval for multimedia databases can be found in the literature [9,10,12,14,17]. The approach we consider is feature extraction. A feature can be seen as a

  18. Feature Extraction Using Fractal Codes

    NARCIS (Netherlands)

    B.A.M. Schouten (Ben); P.M. de Zeeuw (Paul)

    1999-01-01

    htmlabstractFast and successful searching for an object in a multimedia database is a highly desirable functionality. Several approaches to content based retrieval for multimedia databases can be found in the literature [9,10,12,14,17]. The approach we consider is feature extraction. A feature can

  19. Extraction of Proteins with ABS

    NARCIS (Netherlands)

    Desai, R.K.; Streefland, M.; Wijffels, R.H.; Eppink, M.H.M.

    2016-01-01

    Over the past years, there has been an increasing trend in research on the extraction and purification of proteins using aqueous biphasic systems (ABS) formed by polymers, e.g., polyethylene glycol (PEG). In general, when dealing with protein purification processes, it is essential to maintain their

  20. Extractive Summarisation of Medical Documents

    Directory of Open Access Journals (Sweden)

    Abeed Sarker

    2012-09-01

    Full Text Available Background Evidence Based Medicine (EBM practice requires practitioners to extract evidence from published medical research when answering clinical queries. Due to the time-consuming nature of this practice, there is a strong motivation for systems that can automatically summarise medical documents and help practitioners find relevant information. Aim The aim of this work is to propose an automatic query-focused, extractive summarisation approach that selects informative sentences from medical documents. MethodWe use a corpus that is specifically designed for summarisation in the EBM domain. We use approximately half the corpus for deriving important statistics associated with the best possible extractive summaries. We take into account factors such as sentence position, length, sentence content, and the type of the query posed. Using the statistics from the first set, we evaluate our approach on a separate set. Evaluation of the qualities of the generated summaries is performed automatically using ROUGE, which is a popular tool for evaluating automatic summaries. Results Our summarisation approach outperforms all baselines (best baseline score: 0.1594; our score 0.1653. Further improvements are achieved when query types are taken into account. Conclusion The quality of extractive summarisation in the medical domain can be significantly improved by incorporating domain knowledge and statistics derived from a specialised corpus. Such techniques can therefore be applied for content selection in end-to-end summarisation systems.

  1. DNA Extraction and Primer Selection

    DEFF Research Database (Denmark)

    Karst, Søren Michael; Nielsen, Per Halkjær; Albertsen, Mads

    Talk regarding pitfalls in DNA extraction and 16S amplicon primer choice when performing community analysis of complex microbial communities. The talk was a part of Workshop 2 "Principles, Potential, and Limitations of Novel Molecular Methods in Water Engineering; from Amplicon Sequencing to -omics...

  2. Butterfly extracts show antibacterial activity

    Science.gov (United States)

    Extracts of several British butterfly species were tested and shown to possess powerful bactericidal activity against the gram-positive bacteria Staphylococcus aureus (S. aureus). The active compounds were identified as hydroxylated pyrrolizidine alkaloids (PAs) related to loline with nitrogen at C-...

  3. Development of new natural extracts.

    Science.gov (United States)

    Lavoine-Hanneguelle, Sophie; Périchet, Christine; Schnaebele, Nicolas; Humbert, Marina

    2014-11-01

    For over the past 20 years, a remarkable development in the study and search of natural products has been observed. This is linked to a new market trend towards ecology and also due to new regulations. This could be a rupture, but also a real booster for creativity. Usually, in the flavor and fragrance field, creativity was boosted by the arrival of new synthetic molecules. Naturals remained the traditional, century-old products, protected by secrecy and specific know-how from each company. Regulatory restrictions or eco-friendly certification constraints like hexane-free processes triggered an important brainstorming in the industry. As a result, we developed new eco-friendly processes including supercritical CO2 extraction, allowing fresh plants to be used to obtain industrial flower extracts (Jasmine Grandiflorum, Jasmine Sambac, Orange blossom). These extracts are analyzed by GC, GC/MS, GCO, and HPTLC techniques. New or unusual raw materials can also be explored, but the resulting extracts have to be tested for safety reasons. Some examples are described. Copyright © 2014 Verlag Helvetica Chimica Acta AG, Zürich.

  4. Miscibility Evaluation Of The Next Generation Solvent With Polymers Currently Used At DWPF, MCU, And Saltstone

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F. F.

    2013-04-17

    The Office of Waste Processing, within the Office of Technology Innovation and Development, funded the development of an enhanced Caustic-Side Solvent Extraction (CSSX) solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. This effort lead to the development of the Next Generation Solvent (NGS) with Tris (3,7-dimethyl octyl) guanidine (TiDG). The first deployment target for the NGS solvent is within the Modular CSSX Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the new chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the affected facility. This report provides the calculated data from exposing these polymers to the Next Generation Solvent. An assessment of the dimensional stability of polymers known to be used or present in the MCU, Defense Waste Processing Facility (DWPF), and Saltstone facilities that will be exposed to the NGS showed that TiDG could selectively affect the elastomers and some thermoplastics to varying extents, but the typical use of these polymers in a confined geometry will likely prevent the NGS from impacting component performance. The polymers identified as of primary concern include Grafoil® (flexible graphite), Tefzel®, Isolast®, ethylene-propylene-diene monomer (EPDM) rubber, nitrile-butadiene rubber (NBR), styrene-butadiene rubber (SBR), ultra high molecular weight polyethylene (UHMWPE), and fluorocarbon rubber (FKM). Certain polymers like NBR and EPDM were found to interact mildly with NGS but their calculated swelling and the confined geometry will impede interaction with NGS. In addition, it was found that Vellumoid (cellulose fibers-reinforced glycerin and protein) may leach protein and Polyvinyl Chloride (PVC) may leach plasticizer (such as Bis-Ethylhexyl-Phthalates) into the NGS solvent. Either case

  5. Repeated extraction of DNA from FTA cards

    DEFF Research Database (Denmark)

    Stangegaard, Michael; Ferrero, Laura; Børsting, Claus

    2011-01-01

    Extraction of DNA using magnetic bead based techniques on automated DNA extraction instruments provides a fast, reliable and reproducible method for DNA extraction from various matrices. However, the yield of extracted DNA from FTA-cards is typically low. Here, we demonstrate that it is possible...... to repeatedly extract DNA from the processed FTA-disk. The method increases the yield from the nanogram range to the microgram range....

  6. Supercritical fluid extraction behaviour of polymer matrices

    International Nuclear Information System (INIS)

    Sujatha, K.; Kumar, R.; Sivaraman, N.; Srinivasan, T.G.; Vasudeva Rao, P.R.

    2007-01-01

    Organic compounds present in polymeric matrices such as neoprene, surgical gloves and PVC were co-extracted during the removal of uranium using supercritical fluid extraction (SFE) technique. Hence SFE studies of these matrices were carried out to establish the extracted species using HPLC, IR and mass spectrometry techniques. The initial study indicated that uranium present in the extract could be purified from the co-extracted organic species. (author)

  7. Data report: western United States

    International Nuclear Information System (INIS)

    Cook, J.R.; Fay, W.M.

    1982-04-01

    This abbreviated summary data report, presents results of ground water and stream surface sediment reconnaissance in the western United States. Surface sediment samples were collected at 67,741 sites, at a target sampling density of one site per 13 square kilometers. Ground water samples were collected at 13,979 sites, and surface water samples were collected at 2,958 sites. Neutron activaton analysis results are given for uranium and 16 other elements in sediments, and for uranium and 9 other elements in waters. Mass spectrometry results are given for helium in ground waters. Supplemental analyses of the sediments for extractable uranium and 22 other elements are given where they are available. Supplemental analyses of water samples for 33 additional elements are also reported where they are available. Analytical data and field measurements are presented in tables on microfiche. Data from ground water sites (on microfiche in pocket) include (1) water chemistry measurements (pH, conductivity, and alkalinity), (2) physical measurements where applicable (water temperature, well description, and scintillometer reading), and (3) elemental analyses (U, Al, Br Cl, Dy, F, Mg, Mn, Na, and V by neutron activation and Ag, Al, As, B, Ba, Be, Ca, Ce, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Nb, Ni, P, Sc, Se, Si, Sr, Th, Ti, V, Y, Zn, and Zr by spectrophotometry). Helium analyses are given for ground water

  8. Chromatographic analysis of wheatgrass extracts

    Directory of Open Access Journals (Sweden)

    Masood Shah Khan

    2015-01-01

    Full Text Available Aim: Wheatgrass (WG is the shoot of Triticum aestivum Linn. belongs to the family Gramineae, and possess high chlorophyll content and essential vitamins, minerals, vital enzymes, amino acids, dietary fibers etc., It has been shown to possess anti-cancer, anti-ulcer, antioxidant, and anti-arthritic activity due to the presence of biologically active compounds, and minerals. Therefore, in the present study, high-performance thin layer chromatography (HPTLC, and high-performance liquid chromatography (HPLC methods for qualitative and quantitative analysis have been proposed, which will help in quality evaluation of wheat grass extract. Materials and Methods: Samples for analysis were prepared in methanol and water simply by sonication. These were applied on pre-coated silica plate and chromatograms were developed using toluene: Ethyl acetate: Formic acid. HPLC analysis was done on Waters HPLC system using water, methanol, and acetonitrile as mobile phase. Merck C18 column has been used. Results: HPTLC finger printing of alcoholic extracts of WG was carried out and found 10–11 spots at different wavelengths 254, 366, and 435 nm. HPLC fingerprinting produced 22 peaks at 256 nm. Quantitative HPTLC analysis was done to determine the gallic acid content, and was found to be 0.077% w/w in aqueous extract. By HPLC, the content of gallic acid and rutin was found to be 0.07%, and 0.04% w/w in aqueous extract of WG. Conclusion: The developed HPLC and HPTLC fingerprinting method can be used for the quality control, and standardization of WG and its extracts used as nutritional supplement.

  9. Coding visual features extracted from video sequences.

    Science.gov (United States)

    Baroffio, Luca; Cesana, Matteo; Redondi, Alessandro; Tagliasacchi, Marco; Tubaro, Stefano

    2014-05-01

    Visual features are successfully exploited in several applications (e.g., visual search, object recognition and tracking, etc.) due to their ability to efficiently represent image content. Several visual analysis tasks require features to be transmitted over a bandwidth-limited network, thus calling for coding techniques to reduce the required bit budget, while attaining a target level of efficiency. In this paper, we propose, for the first time, a coding architecture designed for local features (e.g., SIFT, SURF) extracted from video sequences. To achieve high coding efficiency, we exploit both spatial and temporal redundancy by means of intraframe and interframe coding modes. In addition, we propose a coding mode decision based on rate-distortion optimization. The proposed coding scheme can be conveniently adopted to implement the analyze-then-compress (ATC) paradigm in the context of visual sensor networks. That is, sets of visual features are extracted from video frames, encoded at remote nodes, and finally transmitted to a central controller that performs visual analysis. This is in contrast to the traditional compress-then-analyze (CTA) paradigm, in which video sequences acquired at a node are compressed and then sent to a central unit for further processing. In this paper, we compare these coding paradigms using metrics that are routinely adopted to evaluate the suitability of visual features in the context of content-based retrieval, object recognition, and tracking. Experimental results demonstrate that, thanks to the significant coding gains achieved by the proposed coding scheme, ATC outperforms CTA with respect to all evaluation metrics.

  10. Rapanos v. United States & Carabell v. United States

    Science.gov (United States)

    Documents associated with guidance for implementing the definition of waters of the United States under the Clean Water Act following the Rapanos v. United States, and Carabell v. United States Supreme Court decision.

  11. In Vitro efficacy of antimicrobial extracts against the atypical ruminant pathogen Mycoplasma mycoides subsp. capri

    Directory of Open Access Journals (Sweden)

    Arjoon Amanda V

    2012-10-01

    Full Text Available Abstract Background Mycoplasmosis is a common infection in human and veterinary medicine, and is associated with chronic inflammation and high morbidity. Mycoplasma species are often intrinsically resistant to many conventional antimicrobial therapies, and the resistance patterns of pathogenic mycoplasmas to commonly used medicinal (antimicrobial plant extracts are currently unknown. Methods Aqueous extracts, ethanol extracts, or oils of the targeted plant species and colloidal silver were prepared or purchased. Activity against the wall-less bacterial pathogen Mycoplasma mycoides subsp. capri was determined and compared to activities measured against Escherichia coli and Bacillus subtilis. Antimicrobial susceptibility testing was performed by broth microdilution assays. The lethal or inhibitory nature of each extract was determined by subculture into neat growth medium. Results Growth of M. mycoides capri, E. coli, and B. subtilis was inhibited by elderberry extract, oregano oil, ethanol extract of oregano leaves, and ethanol extract of goldenseal root. No inhibition was seen with aqueous extract of astragalus or calendula oil. Growth of M. mycoides capri and B. subtilis was inhibited by ethanol extract of astragalus, whereas growth of E. coli was not. Similarly, M. mycoides capri and E. coli were inhibited by aqueous extract of thyme, but B. subtilis was unaffected. Only B. subtilis was inhibited by colloidal silver. Measured MICs ranged from 0.0003 mg/mL to 3.8 mg/mL. Bacteriostatic and bactericidal effects differed by species and extract. Conclusions The atypical pathogen M. mycoides capri was sensitive to extracts from many medicinal plants commonly used as antimicrobials in states of preparation and concentrations currently available for purchase in the United States and Europe. Variation in bacteriostatic and bactericidal activities between species and extracts indicates that multiple effecter compounds are present in these plant species.

  12. In Vitro efficacy of antimicrobial extracts against the atypical ruminant pathogen Mycoplasma mycoides subsp. capri.

    Science.gov (United States)

    Arjoon, Amanda V; Saylor, Charlotte V; May, Meghan

    2012-10-02

    Mycoplasmosis is a common infection in human and veterinary medicine, and is associated with chronic inflammation and high morbidity. Mycoplasma species are often intrinsically resistant to many conventional antimicrobial therapies, and the resistance patterns of pathogenic mycoplasmas to commonly used medicinal (antimicrobial) plant extracts are currently unknown. Aqueous extracts, ethanol extracts, or oils of the targeted plant species and colloidal silver were prepared or purchased. Activity against the wall-less bacterial pathogen Mycoplasma mycoides subsp. capri was determined and compared to activities measured against Escherichia coli and Bacillus subtilis. Antimicrobial susceptibility testing was performed by broth microdilution assays. The lethal or inhibitory nature of each extract was determined by subculture into neat growth medium. Growth of M. mycoides capri, E. coli, and B. subtilis was inhibited by elderberry extract, oregano oil, ethanol extract of oregano leaves, and ethanol extract of goldenseal root. No inhibition was seen with aqueous extract of astragalus or calendula oil. Growth of M. mycoides capri and B. subtilis was inhibited by ethanol extract of astragalus, whereas growth of E. coli was not. Similarly, M. mycoides capri and E. coli were inhibited by aqueous extract of thyme, but B. subtilis was unaffected. Only B. subtilis was inhibited by colloidal silver. Measured MICs ranged from 0.0003 mg/mL to 3.8 mg/mL. Bacteriostatic and bactericidal effects differed by species and extract. The atypical pathogen M. mycoides capri was sensitive to extracts from many medicinal plants commonly used as antimicrobials in states of preparation and concentrations currently available for purchase in the United States and Europe. Variation in bacteriostatic and bactericidal activities between species and extracts indicates that multiple effecter compounds are present in these plant species.

  13. Solvent extraction of aurocyanide by extractant CTMAB and TBP

    International Nuclear Information System (INIS)

    Yan Wenfei; Zhang Tianxi; Wu Jinguang

    2000-01-01

    A novel extraction system using KAu(CN) 2 -CTMAB as aqueous phase and 30% TBP-dodecane as organic phase is studied by 198 Au radioactive tracer and FT-IR spectroscopy. The results show that the organic phase separates into two phases, when the gold concentration is bigger than 20 g/L. From the analysis of FT-IR it is seen that the most of gold is in the lower organic phase

  14. Recent trends in metals extraction

    Directory of Open Access Journals (Sweden)

    Regel-Rosocka, M.

    2013-08-01

    Full Text Available After near 70 years of practical usage, solvent extraction is a perfectly mastered technique of separation, widely used on an industrial scale for the separation of metals mainly from raw materials. However, currently, in the era of depleting natural resources and increasingly less accessible deposits, environmental restrictions, etc., an increasing interest, both from social and economical constrains, is being directed at the extraction of metals from the secondary sources (such as batteries, electronic scrap. In many cases, solvent extraction, due to its operational characteristics, can be considered as the Best Available Technology for the purpose of separating multielemental metal solutions. This paper provides a brief overview of past achievements and present scenario of solvent extraction investigations and developments, describing some recently commissioned solvent extraction plants, whereas the Skorpion Zinc plant (Namibia for zinc extraction from raw materials and caesium removal from radioactive High Level Wastes (HLWs are told over in detail as case studies. The paper also presents some proposals for the use of liquid-liquid extraction to separate metal ions from secondary sources (e.g. cobalt from industrial waste streams. The review highlights the emerging use of ionic liquids as new extractants for metals, providing an insight into this exciting research field. Despite its detractors, solvent extraction has entered in force into XXI century as a leading separation technology for metals.Después de casi 70 años de uso práctico, la extracción líquido-líquido o extracción con disolventes es una técnica de separación muy evolucionada, utilizándose a escala industrial en el beneficio de metales obtenidos de diversas materias primas. Sin embargo, con el agotamiento de los recursos naturales y el aumento de depósitos minerales de más difícil acceso, restricciones medio ambientales, etc., ha aumentado el interés, tanto desde

  15. Extraction of pectin from apple pomace

    Directory of Open Access Journals (Sweden)

    Maria Helene Canteri-Schemin

    2005-03-01

    Full Text Available As apple-processing units are now in expansion in Brazil, industrial by-products like pomace play an important role in pectin manufacture. The objective of this article was to determine a pratical follow-up to the extraction of pectin from apple pomace and to characterize it in a laboratory, on a small scale, aiming at establishing the optimum conditions for acid extraction. The highest yields were obtained when [1]apple pomace was dried and ground to obtain an apple flour to be used as raw material, [2] citric or nitric acids were used and [3] when the citric acid concentration was 6.2 g/100 ml and the time of reaction was 153 minutes. The apple variety in itself was not significant in pectin yield. The degree of esterification (DE = 68.84 % of the product obtained, as well as its physical looks, show the success of pectin extraction.No aproveitamento de resíduos das indústrias processadoras de maçã, em expansão no Brasil, a pectina alimentícia surge como importante subproduto. Os objetivos deste trabalho foram os seguintes: extração e caracterização da pectina de bagaço de maçã em bancada, em que as condições para maior rendimento de obtenção em relação ao tipo de ácido, ao tamanho das partículas e à variedade de maçã foram estabelecidas. Objetivou-se também a otimização da produção, levando-se em conta o tempo e a concentração do ácido cítrico. Foram considerados métodos de extração mais eficientes quanto ao rendimento: [1] acidificação com ácido cítrico ou ácido nítrico, [2] cominuição do bagaço, usando a farinha como matéria-prima, com partículas retidas no tamis de 106 µm, [3] concentração de ácido de 6,2 g% e tempo de extração de 153 minutos. A variedade da maçã não interferiu significativamente no rendimento. A alta metoxilação (DE= 68,84% das pectinas produzidas em bancada confirma o grau de maturidade das matérias-primas usadas nos experimentos.

  16. Application of molecular sieves in the fractionation of lemongrass oil from high-pressure carbon dioxide extraction

    Directory of Open Access Journals (Sweden)

    L. Paviani

    2006-06-01

    Full Text Available The aim of this work was to study the feasibility of simultaneous process of high-pressure extraction and fractionation of lemongrass essential oil using molecular sieves. For this purpose, a high-pressure laboratory-scale extraction unit coupled with a column with four different stationary phases for fractionation: ZSM5 zeolite, MCM-41 mesoporous material, alumina and silica was employed. Additionally, the effect of carbon dioxide extraction variables on the global yield and chemical composition of the essential oil was also studied in a temperature range of 293 to 313 K and a pressure range of 100 to 200 bar. The volatile organic compounds of the extracts were identified by a gas chromatograph coupled with a mass spectrometer detector (GC/MS. The results indicated that the extraction process variables and the stationary phase exerted an effect on both the extraction yield and the chemical composition of the extracts.

  17. A comparative study of Averrhoabilimbi extraction method

    Science.gov (United States)

    Zulhaimi, H. I.; Rosli, I. R.; Kasim, K. F.; Akmal, H. Muhammad; Nuradibah, M. A.; Sam, S. T.

    2017-09-01

    In recent year, bioactive compound in plant has become a limelight in the food and pharmaceutical market, leading to research interest to implement effective technologies for extracting bioactive substance. Therefore, this study is focusing on extraction of Averrhoabilimbi by different extraction technique namely, maceration and ultrasound-assisted extraction. Fewplant partsof Averrhoabilimbiweretaken as extraction samples which are fruits, leaves and twig. Different solvents such as methanol, ethanol and distilled water were utilized in the process. Fruit extractsresult in highest extraction yield compared to other plant parts. Ethanol and distilled water have significant role compared to methanol in all parts and both extraction technique. The result also shows that ultrasound-assisted extraction gave comparable result with maceration. Besides, the shorter period on extraction process gives useful in term of implementation to industries.

  18. Characterization of in vivo anti-rotavirus activities of saponin extracts from Quillaja Saponaria Molina

    Science.gov (United States)

    Tam, Ka Ian; Roner, Michael R.

    2011-01-01

    Rotavirus is the leading cause of severe diarrhea disease in newborns and young children worldwide with approximately 300,000 pre-adolescent deaths each year. Quillaja saponins are a natural aqueous extract obtained from the Chilean soapbark tree. The extract is approved for use in humans by the FDA for use in beverages as a food addictive. We have demonstrated that Quillaja extracts have strong antiviral activities in vitro against six different viruses. In this study, we evaluated the in vivo antiviral activity of these extracts against rhesus rotavirus (RRV) using a mouse model. We established that at a dosage of 0.015 mg/mouse of saponin extract, RRV induced diarrhea can be significantly reduced from 79% to 11% when mice are exposed to 500 plaque-forming-units (PFU) for each of five consecutive days. Additionally, while a reduction of RRV induced diarrhea depended both on the concentration of virus introduced and on the amount of Quillaja extract given to each mouse, the severity and interval of diarrhea under a variety of conditions tested, in all the treated mice were greatly reduced when compared to those that did not receive the Quillaja extracts. Mechanistically, there is strong evidence that the Quillaja extracts are able to “block” rotavirus infection by inhibiting virus-host attachment through disruption of cellular membrane proteins and/or virus receptors. We believe that Quillaja extracts have promise as antivirals to reduce rotavirus infection and the severity of the disease in humans. PMID:21549151

  19. Music video shot segmentation using independent component analysis and keyframe extraction based on image complexity

    Science.gov (United States)

    Li, Wei; Chen, Ting; Zhang, Wenjun; Shi, Yunyu; Li, Jun

    2012-04-01

    In recent years, Music video data is increasing at an astonishing speed. Shot segmentation and keyframe extraction constitute a fundamental unit in organizing, indexing, retrieving video content. In this paper a unified framework is proposed to detect the shot boundaries and extract the keyframe of a shot. Music video is first segmented to shots by illumination-invariant chromaticity histogram in independent component (IC) analysis feature space .Then we presents a new metric, image complexity, to extract keyframe in a shot which is computed by ICs. Experimental results show the framework is effective and has a good performance.

  20. Simple, Safe, and Cost-Effective Technique for Resected Stomach Extraction in Laparoscopic Sleeve Gastrectomy.

    Science.gov (United States)

    Derici, Serhan; Atila, Koray; Bora, Seymen; Yener, Serkan

    2016-01-01

    Background. Laparoscopic sleeve gastrectomy (LSG) has become a popular operation during the recent years. This procedure requires resection of 80-90% of the stomach. Extraction of gastric specimen is known to be a challenging and costly stage of the operation. In this paper, we report results of a simple and cost-effective specimen extraction technique which was applied to 137 consecutive LSG patients. Methods. Between October 2013 and October 2015, 137 laparoscopic sleeve gastrectomy surgeries were performed at Dokuz Eylul University General Surgery Department, Upper Gastrointestinal Surgery Unit. All specimens were extracted through a 15 mm trocar site without using any special device. Results. We noticed one superficial incisional surgical site infection and treated this patient with oral antibiotics. No cases of trocar site hernia were observed. Conclusion. Different techniques have been described for specimen extraction. This simple technique allows extraction of specimen safely in a short time and does not require any special device.

  1. Enhancing polyphenol extraction from unripe apples by carbohydrate-hydrolyzing enzymes.

    Science.gov (United States)

    Zheng, Hu-zhe; Hwang, In-Wook; Chung, Shin-Kyo

    2009-12-01

    The effects of process variables such as enzyme types, enzyme ratio, reaction temperature, pH, time, and ethanol concentration on the extraction of unripe apple polyphenol were investigated. The results indicated that Viscozyme L had the strongest effect on polyphenols extraction and was selected to study the polyphenol composition. The ratio of enzyme (Viscozyme L) to substrate (2 fungal beta-glucanase units (FBG)) at 0.02, reaction at pH 3.7, 50 degrees C for 12 h, and ethanol concentration of 70% were chosen as the most favorable extraction condition. Total phenolic content (TPC), reducing sugar content (RSC), and extraction yield increased by about 3, 1.5, and 2 times, respectively, compared with control. The contents of p-coumaric acid, ferulic acid, and caffeic acid increased to 8, 4, and 32 times, respectively. The enzyme-aided polyphenol extraction process from unripe apples might be applied to food industry for enhancing bioactive compound production.

  2. Gas-centrifuge unit

    International Nuclear Information System (INIS)

    Stark, T.M.

    1977-01-01

    An isotope-enrichment unit is described for separating a gaseous mixture feedstock including a compound of a light nuclear isotope at a predetermined concentration and a compound of a heavy nuclear isotope at a predetermined concentration into at least two unit-output fractions including a waste fraction depleted in the light isotope to a predetermined concentration and a product fraction enriched in the light isotope to a predetermined concentration. The unit comprises a first group of cascades of gas centrifuges, each cascade having an enriching stage, a stripping stage, an input, a light-fraction output, and a heavy-fraction output for separating the gaseous-mixture feed stock into light and heavy gaseous-mixture fractions; and an auxillary cascade

  3. Mechanical strainer unit

    International Nuclear Information System (INIS)

    Kraeling, J.B.; Netkowicz, R.J.; Schnall, I.H.

    1983-01-01

    The mechanical strainer unit is connected to a flanged conduit which originates in and extends out of a suppression chamber in a nuclear reactor. The strainer includes a plurality of centrally apertured plates positioned along a common central axis and in parallel and spaced relationship. The plates have a plurality of bores radially spaced about the central axis. Spacer means such as washers are positioned between adjacent plates to maintain the plates is spaced relationship and form communicating passages of a predetermined size to the central apertures. Connecting means such as bolts or studs extend through the aligned bores to maintain the unit in assembled relationship and secure the unit to the pipe. By employing perforated plates and blocking off certain of the communicating passages, a dual straining effect can be achieved

  4. Extracting messages masked by chaos

    International Nuclear Information System (INIS)

    Perez, G.; Cerdeira, H.A.

    1995-01-01

    We show how to extract messages that are masked by a chaotic signal in a system of two Lorenz oscillators. This mask removal is done for two different modes of transmission, a digital one where a parameter of the sender is switched between two values, and an analog mode, where a small amplitude message is added to the carrier signal. We achieve this without using a second Lorenz oscillator as receiver, and without doing a full reconstruction of the dynamics. This method is robust with respect to transformations that impede the unmasking using a Lorenz receiver, and is not affected by the broad-band noise that is inherent to the synchronization process. We also discuss the limitations of this way of extraction for messages in high frequency bands. (author). 12 refs, 4 figs

  5. The extraction neptunium by trilaurylamine

    International Nuclear Information System (INIS)

    Champion, J.; Chesne, A.

    1964-01-01

    The extraction by trilaurylamine of neptunium (IV) from nitric acid and sulfuric acid-nitric acid media has been studied with the aim of developing a purification process for this element. Relative to the plutonium-neptunium separation, conditions are given for the oxidation of neptunium (IV) in sulfuric acid-nitric acid medium and data are presented on the stabilisation of the + 4 oxidation state by the organic solvent. Two procedures have been developed for the simultaneous purification of the two actinides. Both are based on the trilaurylamine extraction of the tetravalent nitrate species. The first utilises a constant redox potential fixed by Fe +++ /Fe ++ couple, while in the second, valencies are determined by successive addition of nitrite and ferrous ions. Gram quantities of neptunium 237 has been recovered from plutonium process solution. Alternate procedures are suggested for the chemical processing of irradiated Np 237 . (authors) [fr

  6. Amine synergism in uranium extraction

    International Nuclear Information System (INIS)

    Rinelli, G.; Abbruzzese, C.

    1977-01-01

    Commercial products based on C 8 to C 12 tertiary amine mixtures are now widely used in the solvent extraction of uranium from sulphuric pregnant solutions. The satisfactory results generally obtained have never required an analysis of the synergistic effects of amine combinations similar to that carried out for the organo-phosphorus compounds. In the research described the increase in the extraction power of an organic phase composed of an amine binary mixture was studied with regard to an aqueous solution from the sulphuric acid treatment of uranium ore. On the basis of the experimental results obtained, it is possible to select the best composition of the amine mixture to ensure a percentage increase in uranium recovery. Bearing in mind the tendency for the yellow-cake price to rise, the study is considered to be a useful contribution in the context of commercial products currently available on the market. (author)

  7. Biopolymer chitin: extraction and characterization

    International Nuclear Information System (INIS)

    Andrade, Sania M.B. de; Ladchumananandasivam, Rasiah

    2011-01-01

    The biopolymers are materials made from renewable sources such as soybean, corn, cane sugar, cellulose and chitin. Chitin is the most abundant biopolymer found in nature, after cellulose. The chemical structure of chitin is distinguished by the hydroxyl group, of structure from cellulose, located at position C-2, which in the chitin is replaced by acetamine group. The objective of this study was to develop the chitin from exoskeletons of Litopenaeus vannamei shrimp, which are discarded as waste, causing pollutions, environmental problems and thus obtain better utilization of these raw materials. It also, show the extraction process and deacetylation of chitosan. The extraction of chitin followed steps of demineralization, desproteinization and deodorization. Chitin and chitosan were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and the thermals properties were analyzed by thermogravimetry (TG/DTG). (author)

  8. Mobile emergency response unit

    International Nuclear Information System (INIS)

    Kadi, W.J.; Trolan, R.T.; Becker, J.F.

    1979-01-01

    The Hotspot quick-response unit was the solution to a requirement to find, identify, and control areas of radioactive contamination at the scene of a nuclear weapons accident. The unit consists of two trucks and two trailers, and is designed to be transported by one U.S. Air Force C-141. One truck (generator truck) carries a 40 kW generator-heater-air conditioner combination, spare tires, and accessories. The other (water truck) carries supplies and a 250-gal water tank. One trailer (counting trailer) contains detecting, counting, and recording equipment. The other (decontaminating trailer) contains a shower, sink, 30-gal hot water tank, and supplies

  9. Extractive metallurgy of the beryllium

    International Nuclear Information System (INIS)

    Alonso, Neusa; Capocchi, Jose Deodoro Trani

    1995-01-01

    A bibliographic review is performed on the beryllium extractive metallurgy. The work describes the main type of ores and processes applied to the metallic beryllium production, beryllium oxide production using fluoride, sulfide and direct chlorination. The thermodynamic consideration are made on beryllium reduction processes, discussing the viability of the beryllium oxide and hallide reduction processes. Under the technological viewpoint, the Cu-Be alloys main production processes are discussed, and the main toxicity problems related with beryllium are mentioned

  10. Metals extraction from sea water

    International Nuclear Information System (INIS)

    Chryssostomidis, C.; Larue, G.J.; Morgan, D.T.

    1981-01-01

    A method and system for continuously extracting metals from sea water by deploying adsorber sheets in a suitable current of sea water, recovering the adsorber sheets after they become loaded with metal and eluting the metal from the recovered sheets. The system involves the use of hollow, perforated bobbins on which the sheets are rolled as they are recovered and through which elutant is introduced

  11. Electrostatic septa for SPS extraction

    CERN Multimedia

    1975-01-01

    The extraction system for the N-Area is located in LSS2 (another one for the W-Area, now abandoned, was in LSS6). The electrostatic septum consists of 4 parts, each 3 m long. It is made of W-wires, 0.12 mm thick. The nominal electric field is 100 kV/cm. See also Annual Report 1975, p.175.

  12. Extraction of sulfuric acid with TOPO

    International Nuclear Information System (INIS)

    Shuyun, Xue; Yonghui, Yang; Yanzhao, Yang; Sixiu, Sun; Borong, Bao

    1998-01-01

    A study on solvent extraction of sulfuric acid by tri-octylphosphine oxide (TOPO) in n-heptane has been made. Extraction coefficients of H 2 SO 4 as a function of H 2 SO 4 concentration in aqueous phase, and extractant concentrations in organic phase have been studied. The composition of extracted species, equilibrium constants of extraction reaction have been evaluated. These results are important for interpreting extraction equilibrium data of uranium(VI) or other metal ions with TOPO in sulfuric acid media. (author)

  13. Extraction of substances assisted by ultrasound (UAE)

    International Nuclear Information System (INIS)

    Azuola, Rocio; Vargas, Pedro

    2007-01-01

    Different compounds present in vegetables with functional or technological properties, have gained great importance in food, pharmaceutical and cosmetic markets. Efficient methods, economical and environment friendly are sought for the extraction of these substances. A literature review has been performanced of recent publications on different extraction methods and their comparison to the ultrasound assisted extraction (UAE) to assess their effectiveness and industrial viability. The ultrasound assisted extraction (UAE) has been found to be more efficient than traditional mining methods, and cheaper and easier than non-traditional extraction methods such as microwave-assisted extraction, so it checks its industrial viability. (author) [es

  14. Pressurized Hot Water Extraction of anthocyanins from red onion: A study on extraction and degradation rates

    Energy Technology Data Exchange (ETDEWEB)

    Petersson, Erik V.; Liu Jiayin; Sjoeberg, Per J.R.; Danielsson, Rolf [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden); Turner, Charlotta, E-mail: Charlotta.Turner@kemi.uu.se [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden)

    2010-03-17

    Pressurized Hot Water Extraction (PHWE) is a quick, efficient and environmentally friendly technique for extractions. However, when using PHWE to extract thermally unstable analytes, extraction and degradation effects occur at the same time, and thereby compete. At first, the extraction effect dominates, but degradation effects soon take over. In this paper, extraction and degradation rates of anthocyanins from red onion were studied with experiments in a static batch reactor at 110 deg. C. A total extraction curve was calculated with data from the actual extraction and degradation curves, showing that more anthocyanins, 21-36% depending on the species, could be extracted if no degradation occurred, but then longer extraction times would be required than those needed to reach the peak level in the apparent extraction curves. The results give information about the different kinetic processes competing during an extraction procedure.

  15. Beam optics of the AmPS extraction line

    International Nuclear Information System (INIS)

    Hoekstra, R.

    1991-01-01

    The design of the Amsterdam Pulse Stretcher includes a feasibility study of part of the extraction trajectory. The latter includes some proposed curves projected through the hall of the beam switch yard. Since extraction is performed in the north line of the ring and the connection to the trajectory of the spectrometers is planned in a trajectory parallel to the east line of the ring the curves contain bending magnets for bending 90 degrees either by only two magnets or by making use of ring bending magnets in the same way as the ring curves are constructed. The bending through 90 degrees has optimal imaging properties of a unit cell much the same as the curves in the ring. This one-to-one (or one-to-minus-one) property is intended to shift the known required beam dimensions stream upwards from a defined point in the trajectory of the spectrometers to be able to create the dimensions at this shifted point by means of a so called beam transformer, placed in between the extraction point and this position. This report deals with the further developments with respect to the extraction trajectory. (author). 5 refs.; 9 figs.; 3 tabs

  16. Ethanol production by extractive fermentation - Process development and technology transfer

    International Nuclear Information System (INIS)

    Daugulis, A.J.; Axford, D.B.; Mau, T.K.

    1991-01-01

    Extractive Fermentation is an ethanol processing strategy in which the operations of fermentation and product recovery are integrated and undertaken simultaneously in a single step. In this process an inert and biocompatible organic solvent is introduced directly into the fermentation vessel to selectively extract the ethanol product. The ethanol is readily recovered from the solvent at high concentration by means of flash vaporization, and the solvent is recycled in a closed loop back to the fermentor. This process is characterized by a high productivity (since ethanol does not build up to inhibitory levels), continuous operation, significantly reduced water consumption, and lower product recovery costs. The technical advantages of this processing strategy have been extensively demonstrated by means of a continuous, fully integrated and computer-controlled Process Demonstration Unit in the authors' laboratory. Numerous features of this technology have been protected by US patent. A thorough economic comparison of Extractive Fermentation relative to modern ethanol technology (continuous with cell recycle) has been completed for both new plants and retrofitting of existing facilities for a capacity of 100 million liters of ethanol per year. Substantial cost savings are possible with Extractive Fermentation ranging, depending on the process configuration, from 5 cents to 16 cents per liter. Activities are under way to transfer this proprietary technology to the private sector

  17. Hierarchical extraction of urban objects from mobile laser scanning data

    Science.gov (United States)

    Yang, Bisheng; Dong, Zhen; Zhao, Gang; Dai, Wenxia

    2015-01-01

    Point clouds collected in urban scenes contain a huge number of points (e.g., billions), numerous objects with significant size variability, complex and incomplete structures, and variable point densities, raising great challenges for the automated extraction of urban objects in the field of photogrammetry, computer vision, and robotics. This paper addresses these challenges by proposing an automated method to extract urban objects robustly and efficiently. The proposed method generates multi-scale supervoxels from 3D point clouds using the point attributes (e.g., colors, intensities) and spatial distances between points, and then segments the supervoxels rather than individual points by combining graph based segmentation with multiple cues (e.g., principal direction, colors) of the supervoxels. The proposed method defines a set of rules for merging segments into meaningful units according to types of urban objects and forms the semantic knowledge of urban objects for the classification of objects. Finally, the proposed method extracts and classifies urban objects in a hierarchical order ranked by the saliency of the segments. Experiments show that the proposed method is efficient and robust for extracting buildings, streetlamps, trees, telegraph poles, traffic signs, cars, and enclosures from mobile laser scanning (MLS) point clouds, with an overall accuracy of 92.3%.

  18. DNA extraction from herbarium specimens.

    Science.gov (United States)

    Drábková, Lenka Záveská

    2014-01-01

    With the expansion of molecular techniques, the historical collections have become widely used. Studying plant DNA using modern molecular techniques such as DNA sequencing plays an important role in understanding evolutionary relationships, identification through DNA barcoding, conservation status, and many other aspects of plant biology. Enormous herbarium collections are an important source of material especially for specimens from areas difficult to access or from taxa that are now extinct. The ability to utilize these specimens greatly enhances the research. However, the process of extracting DNA from herbarium specimens is often fraught with difficulty related to such variables as plant chemistry, drying method of the specimen, and chemical treatment of the specimen. Although many methods have been developed for extraction of DNA from herbarium specimens, the most frequently used are modified CTAB and DNeasy Plant Mini Kit protocols. Nine selected protocols in this chapter have been successfully used for high-quality DNA extraction from different kinds of plant herbarium tissues. These methods differ primarily with respect to their requirements for input material (from algae to vascular plants), type of the plant tissue (leaves with incrustations, sclerenchyma strands, mucilaginous tissues, needles, seeds), and further possible applications (PCR-based methods or microsatellites, AFLP).

  19. Sequence complexity and work extraction

    International Nuclear Information System (INIS)

    Merhav, Neri

    2015-01-01

    We consider a simplified version of a solvable model by Mandal and Jarzynski, which constructively demonstrates the interplay between work extraction and the increase of the Shannon entropy of an information reservoir which is in contact with a physical system. We extend Mandal and Jarzynski’s main findings in several directions: first, we allow sequences of correlated bits rather than just independent bits. Secondly, at least for the case of binary information, we show that, in fact, the Shannon entropy is only one measure of complexity of the information that must increase in order for work to be extracted. The extracted work can also be upper bounded in terms of the increase in other quantities that measure complexity, like the predictability of future bits from past ones. Third, we provide an extension to the case of non-binary information (i.e. a larger alphabet), and finally, we extend the scope to the case where the incoming bits (before the interaction) form an individual sequence, rather than a random one. In this case, the entropy before the interaction can be replaced by the Lempel–Ziv (LZ) complexity of the incoming sequence, a fact that gives rise to an entropic meaning of the LZ complexity, not only in information theory, but also in physics. (paper)

  20. Extractive reserves in Brazilian Amazonia

    Energy Technology Data Exchange (ETDEWEB)

    Fearnside, P.M (National Institute for Research in the Amazon, Manaus-Amazonas (Brazil))

    1989-06-01

    In 1985 an opportunity arose for maintaining tracts of Amazonian forest under sustainable use. Brazil's National Council of Rubber Tappers and the Rural Worker's Union proposed the creation of a set of reserves of a new type, called extractive reserves. The first six are being established in one of the Brazilian states most threatened by deforestatation. The creation of extractive reserves grants legal protection to forest land traditionally used by rubber tappers, Brazil-nut gatherers, and other extractivists. The term extrativismo (extractivism) in Brazil refers to removing nontimber forest products, such as latex, resins, and nuts, without felling the trees. Approximately 30 products are collected for commercial sale. Many more types of forest materials are gathered, for example as food and medicines, for the extractivists' own use. The reserve proposal is attractive for several reasons related to social problems. It allows the rubber tappers to continue their livelihood rather than be expelled by deforestation. However, it is unlikely that sufficient land will be set aside as extractive reserves to employ all the tappers. Displaced rubber tappers already swell the ranks of urban slum dwellers in Brazil's Amazonian cities, and they have become refugees to continue their profession in the forests of neighboring countries, such as Bolivia.

  1. Stability of extraction space closure.

    Science.gov (United States)

    Garib, Daniela Gamba; Bressane, Larissa Borges; Janson, Guilherme; Gribel, Bruno Frazão

    2016-01-01

    The objectives of this study were to evaluate the prevalence and long-term behavior of extraction space reopening in patients with Class I malocclusion and to identify some associated factors. A sample of 43 patients met the inclusion criteria. Dental casts at the onset of treatment, after treatment, and 1 and 5 years after debonding were used. Initial and final cephalometric radiographs were used to measure the amount of incisor retraction. Cochran tests were used to compare the numbers of open and closed extraction spaces after treatment and at 1 and 5 years after debonding (P space reopening with t tests. Of the sample, 30.23% had extraction space reopening. The frequency of open spaces significantly increased between the final and the 1-year posttreatment dental casts and decreased between the casts at 1 and 5 years posttreatment. Patients with space reopening had less initial anterior crowding and greater amounts of mandibular incisor retraction during treatment. There was a high prevalence of space reopening 1 year after treatment. However, these spaces tended to decrease by 5 years after treatment. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  2. Titanium metal: extraction to application

    Energy Technology Data Exchange (ETDEWEB)

    Gambogi, Joseph (USGS, Reston, VA); Gerdemann, Stephen J.

    2002-09-01

    In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of rutile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium. In this paper, we discuss all aspects of the titanium industry from ore deposits through extraction to present and future applications. The methods of both primary (mining of ore, extraction, and purification) and secondary (forming and machining) operations will be analyzed. The chemical and physical properties of titanium metal will be briefly examined. Present and future applications for titanium will be discussed. Finally, the economics of titanium metal production also are analyzed as well as the advantages and disadvantages of various alternative extraction methods.

  3. Experimental and numerical investigations of oscillations in extracted material parameters for finite Bragg stacks using the NRW method

    DEFF Research Database (Denmark)

    Clausen, Niels Christian Jerichau; Arslanagic, Samel; Breinbjerg, Olav

    2012-01-01

    A 1D dielectric finite Bragg stack situated in a rectangular waveguide and illuminated by the fundamental TE10 mode is examined analytically, numerically, and experimentally. Calculated as well as measured scattering parameters are used to extract the effective/equivalent material parameters...... for three specific configurations of its constituent unit cell. Particular attention is devoted to the absence/presence of certain oscillations in the extracted material parameters, depending on the unit cell configuration. The results for the finite Bragg stack are further verified to agree with those...... of an infinite Bragg stack, for which the dispersion equation is used in conjunction with the Floquet-Bloch harmonics expansion to extract the material parameters. It is shown that the extracted material parameters for the finite and infinite Bragg stacks agree for the symmetric unit cell configuration....

  4. [The role of occlusion and extraction in orthodontics. Historical overview].

    Science.gov (United States)

    Kucsera, Agnes; Struhár, Gabriella

    2012-03-01

    Occlusion is important in each unit of dentistry. The authors describe not only the meaning of normal occlusion and dysgnathy but also the historical background focusing on the most important orthodontists, their achievements and literary works. This article gives an overview of the development of orthodontics from the very beginning (ancient times) to nowadays. The most important figures of these periods are: P. Fauchard, F. C. Kneisel, E. H. Angle, C. Case (dark ages); C. F. Ballard, P. R. Begg, C. H. Tweed (golden ages); L. F. Andrews and R. H. Roth (contemporary period). Along these three eras development and changing of the extraction-principles are shown. Nowadays the orthodontists still use Angle's classification and orthodontic treatment with extraction is also accepted. However it is not a separate treatment method, but only used as complement treatment. The authors stress on the importance of normal occlusion, which should be result of every orthodontic, but also prothetic and gnathological treatment.

  5. Microfluidic process monitor for industrial solvent extraction system

    Science.gov (United States)

    Gelis, Artem; Pereira, Candido; Nichols, Kevin Paul Flood

    2016-01-12

    The present invention provides a system for solvent extraction utilizing a first electrode with a raised area formed on its surface, which defines a portion of a microfluidic channel; a second electrode with a flat surface, defining another portion of the microfluidic channel that opposes the raised area of the first electrode; a reversibly deformable substrate disposed between the first electrode and second electrode, adapted to accommodate the raised area of the first electrode and having a portion that extends beyond the raised area of the first electrode, that portion defining the remaining portions of the microfluidic channel; and an electrolyte of at least two immiscible liquids that flows through the microfluidic channel. Also provided is a system for performing multiple solvent extractions utilizing several microfluidic chips or unit operations connected in series.

  6. Allergen extracts for immunotherapy in Latin America

    Directory of Open Access Journals (Sweden)

    Ricardo Cardona-Villa

    2018-04-01

    Full Text Available Background: The Latin American Society of Allergy, Asthma, and Immunology (SLAAI presents a document about the use of immunotherapy (IT in Latin America, where administration patterns, indications and contraindications, effects on health, adverse events and socioeconomic impact are reviewed. Objective: To review publications analyzing the use of IT in Latin America. Methods: A literature review was carried out in order to identify works addressing IT in Latin America. This review was focused on practical scientific information available on IT in the region, and a parallel comparison was made with practices observed in the United States and European countries. Results: Of the 21 Latin American countries included, only 9 had original articles meeting the selection criteria; a total of 82 articles were selected, most of them from Brazil and Mexico. Most widely used allergenic extracts in Latin America tropical and subtropical regions were those of mites and pollen. Conclusion: Although it is true that there are huge challenges for the future of IT in Latin America, studies on subcutaneous IT and sublingual IT are increasing, but most of them are retrospective and some have design bias, and more prospective studies are therefore required, using internationally validated scales for clinical evaluation.

  7. Transfer of manufacturing units

    DEFF Research Database (Denmark)

    Madsen, Erik Skov; Riis, Jens Ove; Sørensen, Brian Vejrum

    2008-01-01

    The ongoing and unfolding relocation of activities is one of the major trends, that calls for attention in the domain of operations management. In particular, prescriptive models outlining: stages of the process, where to locate, and how to establish the new facilities have been studied, while...... and dilemmas to be addressed when transferring manufacturing units....

  8. United States Attorney Prosecutions

    Science.gov (United States)

    1993-10-01

    property of CocaCola Bottling Company, Fayetteville, North Carolina, of a value in excess of $100.00, in violation of Title 18 United States Code, Section...another, to-wit: a Cocacola soft drink machine, the amount of damage to said personal property being more than $200.00, in violation of North Carolina

  9. Planter unit test stand

    Science.gov (United States)

    A planter test stand was developed to evaluate individual row-crop metering units in early 2013. This test stand provided the ability to quantify actual seed metering in terms of population, seed spacing, skips, and multiples over a range of meter RPMs and vacuum pressures. Preliminary data has been...

  10. United Kingdom's experience

    International Nuclear Information System (INIS)

    Drummond, S.M.

    1994-01-01

    This is a presentation of the United Kingdom's experience with power transmission open access. The topics of the presentation include the objectives of changing, commercial arrangements and economic drivers, long term effects, the effects of moving to a more competitive environment, and factors affecting open access such as political climate and market regulation

  11. Whale Teaching Unit.

    Science.gov (United States)

    Peninsula Humane Society, San Mateo, CA.

    Materials in this teaching unit are designed to foster an interest in whale preservation among intermediate grade and junior high school students. Several readings provide background information on various types of whales and the economic value of whales. Student activities include a true and false game, a crossword, and a mobile. A resource list…

  12. Multifunctional centrifugal grinding unit

    Science.gov (United States)

    Sevostyanov, V. S.; Uralskij, V. I.; Uralskij, A. V.; Sinitsa, E. V.

    2018-03-01

    The article presents scientific and engineering developments of multifunctional centrifugal grinding unit in which the selective effect of grinding bodies on the crushing material is realized, depending on its physical and mechanical characteristics and various schemes for organizing the technological process

  13. United in change

    NARCIS (Netherlands)

    Hanneke Posthumus; Josje den Ridder; Joep de Hart

    2014-01-01

    Original title: Verenigd in verandering The importance of citizens who unite in civil society organisations is broadly recognised. Organisations bind people to each other, to the community and to the political system. How are civil-society organisations in the Netherlands faring? Is there

  14. Unit III: International Conflict.

    Science.gov (United States)

    Maxey, Phyllis

    1983-01-01

    This lesson helps students understand the global network involved in international events. Students have an opportunity to examine the impact of international law and the role of international organizations, national governments, and private individuals in the effort to secure the release of United States hostages in Iran. (AM)

  15. Unit 16 - Output

    OpenAIRE

    Unit 16, CC in GIS; Star, Jeffrey L.

    1990-01-01

    This unit discusses issues related to GIS output, including the different types of output possible and the hardware for producing each. It describes text, graphic and digital data that can be generated by a GIS as well as line printers, dot matrix printers/plotters, pen plotters, optical scanners and cathode ray tubes (CRTs) as technologies for generating the output.

  16. Defining line replaceable units

    NARCIS (Netherlands)

    Parada Puig, J. E.; Basten, R. J I

    2015-01-01

    Defective capital assets may be quickly restored to their operational condition by replacing the item that has failed. The item that is replaced is called the Line Replaceable Unit (LRU), and the so-called LRU definition problem is the problem of deciding on which item to replace upon each type of

  17. Urgency in energy justice : contestation and time in prospective shale extraction in the United States and United Kingdom

    OpenAIRE

    Partridge, Tristan

    2018-01-01

    Changes to the material and social systems that underpin energy infrastructures are inextricably linked to energy justice concerns, and the timeframes of those changes significantly affect their outcomes. Temporal aspects of energy initiatives and their impacts are thus an important site for examining emergent public views on new energy proposals, inequality, and energy justice. We propose urgency is a particularly rich concept through which to study (i) the justice and socioenvironmental imp...

  18. Improving the extraction-and-loading process in the open mining operations

    Directory of Open Access Journals (Sweden)

    Cheban A. Yu.

    2017-09-01

    Full Text Available Using the explosions is the main way to prepare solid rocks for the excavation, and that results in the formation of a rock mass of uneven granulometric composition, which makes it impossible to use a conveyor quarry transport without the preliminary large crushing of the rock mass obtained during the explosion. A way to achieve the greatest technical and economic effect is the full conveyorization of quarry transport, what, in this case, ensures the sequenced-flow of transport operations, automation of management and high labor productivity. The extraction-and-loading machines are the determining factor in the performance of mining and transport machines in the technological flow of the quarry. When extracting a blasted rock mass with single-bucket excavators or loaders working in combination with bottom-hole conveyors, one uses self-propelled crushing and reloading units of various designs to grind large individual parts to fractions of conditioning size. The presence of a crushing and reloading unit in the pit-face along with the excavator requires an additional space for its placement, complicates the maneuvering of the equipment in the pit-face, and increases the number of personnel and the cost of maintaining the extraction-and-reloading operations. The article proposes an improved method for carrying out the extraction-and-loading process, as well as the design of extraction-and-grinding unit based on a quarry hydraulic excavator. The design of the proposed unit makes it possible to convert the cyclic process of scooping the rock mass into the continuous process of its loading on the bottom-hole conveyor. Using the extraction-and-grinding unit allows one to combine the processes of excavation, preliminary crushing and loading of the rock mass, which ensures an increase in the efficiency of mining operations.

  19. Digital extraction of interference fringe contours

    International Nuclear Information System (INIS)

    Mastin, G.A.; Ghiglia, D.C.

    1985-01-01

    Two basic techniques for extracting interferogram contours have been discussed. The first is a global contour extracton technique based on the fast Fourier transform. The second extracts individual contours with a thinning algorithm using logical neighborhood transformations

  20. CANINE ECTOPIC TREATMENT WITH FIRST MOLAR EXTRACTION

    Directory of Open Access Journals (Sweden)

    Angelica Margo

    2015-06-01

    Full Text Available Decision to extract or not and the type of tooth must be analyzed carefully in orthodontic treatment. Preferable tooth to be extracted was the tooth with large caries or restoration. Usually the type of tooth to be extracted was second molar (if the third molar appears, incisor, first molar, and combination of several teeth. Orthodontic treatment with molar extraction is more difficult to treat and the result is usually compromise. There are several considerations in extracting first molar such as tooth with large caries or restoration, hypoplasia, periapical disease, large discrepancy, high maxilla-mandibular plane angle, and cases with anterior open bite. Nowadays, orthodontic cases with molar extraction do not prolong the treatment time compared to premolar extraction case, but the anchorage system must be considered carefully. The present case was treated with extraction of first molar to solve anterior crowding with maximum anchorage at the upper jaw and using Nance Holding Appliance.

  1. Portulaca oleracea Linn seed extract ameliorates hydrogen ...

    African Journals Online (AJOL)

    Portulaca oleracea Linn seed extract ameliorates hydrogen ... induced cell death by inhibiting oxidative stress and ROS generation. Keywords: ... culture medium; therefore the stock solutions of ... acetic acid (1 %) and ethanol (50 %) to extract.

  2. EVALUATION OF EXTRACTS FROM Tapinanthus dodone ...

    African Journals Online (AJOL)

    userpc

    flavonoids, tannins, saponins, glycosides ethanolic leaf extract from ... of Chemistry, Kano University of Science and Technology, Wudil. P.M.B. 3244, Kano ... ethanolic leaf extract from Tapinanthus dodoneifolius grown ee. Results obtained for ...

  3. Inflation of Unreefed and Reefed Extraction Parachutes

    Science.gov (United States)

    Ray, Eric S.; Varela, Jose G.

    2015-01-01

    Data from the Orion and several other test programs have been used to reconstruct inflation parameters for 28 ft Do extraction parachutes as well as the parent aircraft pitch response during extraction. The inflation force generated by extraction parachutes is recorded directly during tow tests but is usually inferred from the payload accelerometer during Low Velocity Airdrop Delivery (LVAD) flight test extractions. Inflation parameters are dependent on the type of parent aircraft, number of canopies, and standard vs. high altitude extraction conditions. For standard altitudes, single canopy inflations are modeled as infinite mass, but the non-symmetric inflations in a cluster are modeled as finite mass. High altitude extractions have necessitated reefing the extraction parachutes, which are best modeled as infinite mass for those conditions. Distributions of aircraft pitch profiles and inflation parameters have been generated for use in Monte Carlo simulations of payload extractions.

  4. Transductive Pattern Learning for Information Extraction

    National Research Council Canada - National Science Library

    McLernon, Brian; Kushmerick, Nicholas

    2006-01-01

    .... We present TPLEX, a semi-supervised learning algorithm for information extraction that can acquire extraction patterns from a small amount of labelled text in conjunction with a large amount of unlabelled text...

  5. Development of blood extraction system designed by female mosquito's blood sampling mechanism for bio-MEMS

    Science.gov (United States)

    Tsuchiya, Kazuyoshi; Nakanishi, Naoyuki; Nakamachi, Eiji

    2005-02-01

    A compact and wearable wristwatch type Bio-MEMS such as a health monitoring system (HMS) to detect blood sugar level for diabetic patient, was newly developed. The HMS consists of (1) a indentation unit with a microneedle to generate the skin penetration force using a shape memory alloy(SMA) actuator, (2) a pumping unit using a bimorph PZT piezoelectric actuator to extract the blood and (3) a gold (Au) electrode as a biosensor immobilized GOx and attached to the gate electrode of MOSFET to detect the amount of Glucose in extracted blood. GOx was immobilized on a self assembled spacer combined with an Au electrode by the cross-link method using BSA as an additional bonding material. The device can extract blood in a few microliter through a painless microneedle with the negative pressure by deflection of the bimorph PZT piezoelectric actuator produced in the blood chamber, by the similar way the female mosquito extracts human blood with muscle motion to flex or relax. The performances of the liquid sampling ability of the pumping unit through a microneedle (3.8mm length, 100μm internal diameter) using the bimorph PZT piezoelectric microactuator were measured. The blood extraction micro device could extract human blood at the speed of 2μl/min, and it is enough volume to measure a glucose level, compared to the amount of commercial based glucose level monitor. The electrode embedded in the blood extraction device chamber could detect electrons generated by the hydrolysis of hydrogen peroxide produced by the reaction between GOx and glucose in a few microliter extracted blood, using the constant electric current measurement system of the MOSFET type hybrid biosensor. The output voltage for the glucose diluted in the chamber was increased lineally with increase of the glucose concentration.

  6. Enzymatic Extraction of Hydroxycinnamic Acids from Coffee Pulp

    Directory of Open Access Journals (Sweden)

    Ernesto Favela-Torres

    2011-01-01

    Full Text Available Ferulic, caffeic, p-coumaric and chlorogenic acids are classified as hydroxycinnamic acids, presenting anticarcinogenic, anti-inflammatory and antioxidant properties. In this work, enzymatic extraction has been studied in order to extract high value-added products like hydroxycinnamic acids from coffee pulp. A commercial pectinase and enzyme extract produced by Rhizomucor pusillus strain 23aIV in solid-state fermentation using olive oil or coffee pulp (CP as an inducer of the feruloyl esterase activity were evaluated separately and mixed. The total content (covalently linked and free of ferulic, caffeic, p-coumaric and chlorogenic acids was 5276 mg per kg of coffee pulp. Distribution was as follows (in %: chlorogenic acid 58.7, caffeic acid 37.6, ferulic acid 2.1 and p-coumaric acid 1.5. Most of the hydroxycinnamic acids were covalently bound to the cell wall (in %: p-coumaric acid 97.2, caffeic acid 94.4, chlorogenic acid 76.9 and ferulic acid 73.4. The content of covalently linked hydroxycinnamic acid was used to calculate the enzyme extraction yield. The maximum carbon dioxide rate for the solid-state fermentation using olive oil as an inducer was higher and it was reached in a short cultivation time. Nevertheless, the feruloyl esterase (FAE activity (units per mg of protein obtained in the fermentation using CP as an inducer was 31.8 % higher in comparison with that obtained in the fermentation using olive oil as the inducer. To our knowledge, this is the first report indicating the composition of both esterified and free ferulic, caffeic, p-coumaric and chlorogenic acids in coffee pulp. The highest yield of extraction of hydroxycinnamic acids was obtained by mixing the produced enzyme extract using coffee pulp as an inducer and a commercial pectinase. Extraction yields were as follows (in %: chlorogenic acid 54.4, ferulic acid 19.8, p-coumaric acid 7.2 and caffeic acid 2.3. An important increase in the added value of coffee pulp was mainly

  7. Uranium extraction from gold-uranium ores

    Energy Technology Data Exchange (ETDEWEB)

    Laskorin, B.N.; Golynko, Z.Sh.

    1981-01-01

    The process of uranium extraction from gold-uranium ores in the South Africa is considered. Flowsheets of reprocessing gold-uranium conglomerates, pile processing and uranium extraction from the ores are presented. Continuous counter flow ion-exchange process of uranium extraction using strong-active or weak-active resins is noted to be the most perspective and economical one. The ion-exchange uranium separation with the succeeding extraction is also the perspective one.

  8. Solvent extraction studies of RERTR silicide fuels

    International Nuclear Information System (INIS)

    Gouge, Anthony P.

    1983-01-01

    Uranium silicide fuels, which are candidate RERTR fuel compositions, may require special considerations in solvent extraction reprocessing. Since Savannah River Plant may be reprocessing RERTR fuels as early as 1985, studies have been conducted at Savannah River Laboratory to demonstrate the solvent extraction behavior of this fuel. Results of solvent extraction studies with both unirradiated and irradiated fuel are presented along with the preliminary RERTR solvent extraction reprocessing flow sheet for Savannah River Plant. (author)

  9. Equipment for extracting and conveying stratified minerals

    Energy Technology Data Exchange (ETDEWEB)

    Blumenthal, G.; Kunzer, H.; Plaga, K.

    1991-08-14

    This invention relates to equipment for extracting stratified minerals and conveying the said minerals along the working face, comprising a trough shaped conveyor run assembled from lengths, a troughed extraction run in lengths matching the lengths of conveyor troughing, which is linked to the top edge of the working face side of the conveyor troughing with freedom to swivel vertically, and a positively guided chain carrying extraction tools and scrapers along the conveyor and extraction runs.

  10. Accelerated Solvent Extraction: An Innovative Sample Extraction Technique for Natural Products

    International Nuclear Information System (INIS)

    Hazlina Ahmad Hassali; Azfar Hanif Abd Aziz; Rosniza Razali

    2015-01-01

    Accelerated solvent extraction (ASE) is one of the novel techniques that have been developed for the extraction of phytochemicals from plants in order to shorten the extraction time, decrease the solvent consumption, increase the extraction yield and enhance the quality of extracts. This technique combines elevated temperatures and pressure with liquid solvents. This paper gives a brief overview of accelerated solvent extraction technique for sample preparation and its application to the extraction of natural products. Through practical examples, the effects of operational parameters such as temperature, volume of solvent used, extraction time and extraction yields on the performance of ASE are discussed. It is demonstrated that ASE technique allows reduced solvent consumption and shorter extraction time, while the extraction yields are even higher than those obtained with conventional methods. (author)

  11. Extraction chromatogrpahy of actinides, ch. 7

    International Nuclear Information System (INIS)

    Mueller, W.

    1975-01-01

    This review on extraction chromatography of actinides emphasizes the important usage of neutral (Tributylphosphate), basic (substituted ammonium salts), and acidic (HDEHP) extractants, and their application to separations of actinides in the di-to hexavalent oxidation state. Furthermore, the actinide extraction by ketones, ethers, alcohols and β-diketones is discussed

  12. Surfactant enhanced non-classical extraction

    International Nuclear Information System (INIS)

    Szymanowski, J.

    2000-01-01

    Surfactant enhanced non-classical extractions are presented and discussed. They include micellar enhanced ultrafiltration and cloud point extraction. The ideas of the processes are given and the main features are presented. They are compared to the classical solvent extraction. The fundamental of micellar solutions and their solubilisation abilities are also discussed. (author)

  13. COMPARISONS OF SOXHLET EXTRACTION, PRESSURIZED LIQUID EXTRACTION, SUPERCRITICAL FLUID EXTRACTION, AND SUBCRITICAL WATER EXTRACTION FOR ENVIRONMENTAL SOLIDS: RECOVERY, SELECTIVITY, AND EFFECTS ON SAMPLE MATRIX. (R825394)

    Science.gov (United States)

    Extractions of a polycyclic aromatic hydrocarbon (PAH)-contaminated soil from a former manufactured gas plant site were performed with a Soxhlet apparatus (18 h), by pressurized liquid extraction (PLE) (50 min at 100°C), supercritical fluid extraction (SFE) (1 h at 150°...

  14. Determining efficient extraction procedure of phytochemicals from ...

    African Journals Online (AJOL)

    Determining efficient extraction procedure of phytochemicals from the fruit paste of Ziziphus abyssinica and Tamarindus indica . ... Methodology and results: The methods used included cold and soxhlet extraction using methanol as the solvent and hot extraction using distilled water. To determine the efficiency in which ...

  15. Surfactant enhanced non-classical extraction

    International Nuclear Information System (INIS)

    Szymanowski, J.

    1999-01-01

    Surfactant enhanced non-classical extractions are presented and discussed. They include micellar enhanced ultrafiltration and cloud point extraction. The ideas of the processes are given and the main features are presented. They are compared to the classical solvent extraction. The fundamental of micellar solutions and their solubilization abilities are also discussed. (author)

  16. An extraction machine for the passage of a chamber

    Energy Technology Data Exchange (ETDEWEB)

    Ponomarev, B Ia; Krupnik, V S; Krut, V S; Nenakhov, D F; Niugai, M V; Sagatov, B S

    1980-05-18

    The subject of the invention is the extraction machine for the passage of a chamber with a direct path of a narrow face and the reverse path of a wide face, comprising an actuation unit, a drive reducer, a shield and hydraulic jack for the control brush, is characterized in that for the purpose of insuring the effectiveness of the overlapping, the zones for the loading of the brushes are equipped with chains, whose one end is reinforced on it in a hinge-like fashion, and the other, on the reducer, with which one of the chains is connected to the hydraulic jack by the control brush.

  17. Organization of extracting molecules of the diamide type: link with the extracting properties?

    International Nuclear Information System (INIS)

    Meridiano, Y.

    2009-02-01

    The aim of these studies is to establish a link between the different organizations of diamide extractants (used in the DIAMEX process) and their extracting properties. The effects of the key parameters leading the liquid-liquid extraction (concentration of extractant, nature of solute, activity of the aqueous phase, nature of the diluent and temperature) are studied: 1) at the supramolecular scale, with the characterization of the extractant organizations by vapor-pressure osmometry (VPO) and small angle neutron and X-ray scattering (SANS/SAXS) experiments; 2) at the molecular scale, with the quantification of the extracted solutes (water, nitric acid, metal nitrate) and the determination of extracted complexes stoichiometries by electro-spray mass spectrometry (ESI-MS) experiments. The DMDOHEMA molecule acts as a classical surfactant and forms aggregates of the reverse micelle type. Taking into account the established supramolecular diagrams, a quantitative link between the extractants structures and their extracting properties has been brought to light. To model the europium nitrate extraction, two approaches have been developed: - an approach based on mass action laws. Extractions equilibria have been proposed taking into account the supramolecular speciation; - an innovative approach considering the extracted ions as adsorbed on a specific surface of the extractant molecule which depends on the extractant organization state. The ion extraction can be considered as a sum of isotherms corresponding to the different states of organization. This approach allows to compare the extraction efficiency of an extracting molecule as a function of its organization state. (author)

  18. [Evaluation of the total biological activity and allergenic composition of allergenic extracts].

    Science.gov (United States)

    Lombardero, M; González, R; Duffort, O; Juan, F; Ayuso, R; Ventas, P; Cortés, C; Carreira, J

    1986-01-01

    In the present study, a complete procedure is presented in order to standardize allergenic extracts, the meaning of which is the measurement of the total allergenic activity and the determination of the allergenic composition. The measurement of the biological activity comprises 2 steps: Preparation of Reference Extracts and determination of their "in vivo" activity. Evaluation of the total allergenic activity of extracts for clinical use. Reference extracts were prepared from the main allergens and their "in vivo" biological activity was determined by a quantitative skin prick test in a sample of at least 30 allergic patients. By definition, the protein concentration of Reference Extract that produces, in the allergic population, a geometric mean wheal of 75 mm.2 has an activity of 100 biological units (BUs). The determination of the biological activity of a problem extract is made by RAST inhibition. The sample is compared with the corresponding Reference Extract by this technique and, from this comparison, it is possible to quantify the activity of the problem extract in biologic units (BUs) with clinical significance. Likewise, different techniques have been used to determine the allergenic composition of extracts. These techniques comprise 2 steps: Separation of the components of the extract. Identification of the components that bind specific human IgE. The separation of the components of the extract has been carried out by isoelectric focusing (IEF) and electrophoresis in the presence of sodium dodecyl sulphate (SDS-PAGE). In order to identify the allergenic components, an immunoblotting technique has been employed. The separated components in the IEF gel or SDS-PAGE gel are transferred to a nitrocellulose sheet and later on, this membrane is overlaid with a serum pool from allergic patients and a mouse monoclonal anti-human IgE, labelled with 125I. Finally, the autoradiography of the nitrocellulose membrane is obtained. In this way it is possible to compare

  19. Hybrid Model of Content Extraction

    DEFF Research Database (Denmark)

    Qureshi, Pir Abdul Rasool; Memon, Nasrullah

    2012-01-01

    We present a hybrid model for content extraction from HTML documents. The model operates on Document Object Model (DOM) tree of the corresponding HTML document. It evaluates each tree node and associated statistical features like link density and text distribution across the node to predict...... significance of the node towards overall content provided by the document. Once significance of the nodes is determined, the formatting characteristics like fonts, styles and the position of the nodes are evaluated to identify the nodes with similar formatting as compared to the significant nodes. The proposed...

  20. The extractive metallurgy of gold

    Energy Technology Data Exchange (ETDEWEB)

    Kongolo, K.; Mwema, M.D. [University of Lubumbashi, Zaire, Gecamines Metallurgical Research Centre, Likasi, Zaire, c/o Gecamines Brussels (Belgium)

    1998-12-15

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied.

  1. PSR extraction kicker system improvements

    International Nuclear Information System (INIS)

    Hardek, T.W.

    1991-01-01

    A program to improve the reliability of hardware required to operate the Los Alamos Proton Storage Ring has been under way for the past three years. The extraction kicker system for the PSR was identified as one candidate for improvement. Pulse modulators produce 50kV pulses 360 nsec in length at up to 24-Hz pulse repetition rate and drive two 4-meter-long stripline electrodes. Sources of difficulty with this system included short width switch tube lifetime, drive cable electrical breakdown, high-voltage connector failure, and occasional electrode breakdown. This paper discusses modifications completed on this system to correct these difficulties. 2 refs., 3 figs

  2. The extractive metallurgy of gold

    Science.gov (United States)

    Kongolo, K.; Mwema, M. D.

    1998-12-01

    Mössbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Mössbauer spectroscopy could be applied.

  3. The extractive metallurgy of gold

    International Nuclear Information System (INIS)

    Kongolo, K.; Mwema, M.D.

    1998-01-01

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied

  4. Keyword extraction by nonextensivity measure.

    Science.gov (United States)

    Mehri, Ali; Darooneh, Amir H

    2011-05-01

    The presence of a long-range correlation in the spatial distribution of a relevant word type, in spite of random occurrences of an irrelevant word type, is an important feature of human-written texts. We classify the correlation between the occurrences of words by nonextensive statistical mechanics for the word-ranking process. In particular, we look at the nonextensivity parameter as an alternative metric to measure the spatial correlation in the text, from which the words may be ranked in terms of this measure. Finally, we compare different methods for keyword extraction. © 2011 American Physical Society

  5. ENTREPRENEURIAL OPPORTUNITIES IN FOOD PROCESSING UNITS (WITH SPECIAL REFERENCES TO BYADGI RED CHILLI COLD STORAGE UNITS IN THE KARNATAKA STATE

    Directory of Open Access Journals (Sweden)

    P. ISHWARA

    2010-01-01

    expertise, power and finance. To conclude, at present many oleoresin extracting units are located at Kerala, Tamil Nadu, West Bengal and in other Countries. Byadgi has got good infrastructure facility which is essential to oleoresin extraction units. Hence, recently an oleoresin extraction unit is established in Byadgi. And also it is necessary to open more oleoresin extraction units. This will increase the demand for the Cold Storages in the study area.

  6. Antimicrobial effects of herbal extracts on Streptococcus mutans and normal oral streptococci.

    Science.gov (United States)

    Lee, Sung-Hoon

    2013-08-01

    Streptococcus mutans is associated with dental caries. A cariogenic biofilm, in particular, has been studied extensively for its role in the formation of dental caries. Herbal extracts such as Cudrania tricuspidata, Sophora flavescens, Ginkgo biloba, and Betula Schmidtii have been used as a folk remedy for treating diseases. The purpose of this study was to evaluate and compare the antibacterial activity of herbal extracts against normal oral streptococci, planktonic and biofilm of S. mutans. Streptococcus gordonii, Streptococcus oralis, Streptococcus salivarius, Streptococcus sanguinis, and S. mutans were cultivated with brain heart infusion broth and susceptibility assay for the herbal extracts was performed according to the protocol of Clinical and Laboratory Standard Institute. Also, S. mutans biofilm was formed on a polystyrene 12-well plate and 8-well chamber glass slip using BHI broth containing 2% sucrose and 1% mannose after conditioning the plate and the glass slip with unstimulated saliva. The biofilm was treated with the herbal extracts in various concentrations and inoculated on Mitis-Salivarius bacitracin agar plate for enumeration of viable S. mutans by counting colony forming units. Planktonic S. mutans showed susceptibility to all of the extracts and S. mutans biofilm exhibited the highest level of sensitivity for the extracts of S. flavescens. The normal oral streptococci exhibited a weak susceptibility in comparison to S. mutans. S. oralis, however, was resistant to all of the extracts. In conclusion, the extract of S. flavescens may be a potential candidate for prevention and management of dental caries.

  7. Contamination analysis unit

    International Nuclear Information System (INIS)

    Gregg, H.R.; Meltzer, M.P.

    1996-01-01

    The portable Contamination Analysis Unit (CAU) measures trace quantities of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surfaces by measuring residual hazardous surface contamination, such as tritium and trace organics. It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings. 1 fig

  8. Combustion strategy : United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, D. [Heriot-Watt Univ., Edingburgh, Scotland (United Kingdom). School of Engineering and Physical Sciences

    2009-07-01

    The United Kingdom's combustion strategy was briefly presented. Government funding sources for universities were listed. The United Kingdom Research Councils that were listed included the Arts and Humanities Research Council (AHRC) and the Biotechnology and Biological Sciences Research Council (BBSRC); the Engineering and Physical Sciences Research Council (EPSRC); the Economic and Social Research Council; the Medical Research Council; the Natural Environment Research Council; and the Science and Technology Facilities Council. The EPSRC supported 65 grants worth 30.5 million pounds. The combustion industry was noted to be dominated by three main players of which one was by far the largest. The 3 key players were Rolls-Royce; Jaguar Land Rover; and Doosan Babcock. Industry and government involvement was also discussed for the BIS Technology Strategy Board, strategy technology areas, and strategy application areas.

  9. Laser color recording unit

    Science.gov (United States)

    Jung, E.

    1984-05-01

    A color recording unit was designed for output and control of digitized picture data within computer controlled reproduction and picture processing systems. In order to get a color proof picture of high quality similar to a color print, together with reduced time and material consumption, a photographic color film material was exposed pixelwise by modulated laser beams of three wavelengths for red, green and blue light. Components of different manufacturers for lasers, acousto-optic modulators and polygon mirrors were tested, also different recording methods as (continuous tone mode or screened mode and with a drum or flatbed recording principle). Besides the application for the graphic arts - the proof recorder CPR 403 with continuous tone color recording with a drum scanner - such a color hardcopy peripheral unit with large picture formats and high resolution can be used in medicine, communication, and satellite picture processing.

  10. PERFORMANCE OF A PACKED LIQUID-LIQUID EXTRACTION COLUMN

    Directory of Open Access Journals (Sweden)

    İ. Metin HASDEMİR

    1999-03-01

    Full Text Available The influence of feed ratios ((LE/LR on the performance of a packed liquid-liquid extraction column, with a diameter of 5.86 cm and a column height of 132 cm was investigated. The column is made of borosilicate glass and packed with 10 x 10 mm glass Raschig rings. In this study, a ternary system composed of water + propionic acid + trichloroethylene was used. The data used to triangular diagram were obtained experimentally. The overall mass transfer coefficients, the numbers of overall mass transfer units, the heights of mass transfer units, the numbers of theoretical stages and height equivalent to a theoretical stage (H. E. T. S. values were calculated and compared with each other.

  11. Model analysis of mechanisms controlling pneumatic soil vapor extraction

    DEFF Research Database (Denmark)

    Høier, Camilla Kruse; Sonnenborg, Torben Obel; Jensen, Karsten Høgh

    2009-01-01

    of heterogeneous soils by enforcing large fluctuating pressure fronts through the contaminated area. Laboratory experiments have suggested that pneumatic SVE considerably improves the recovery rate from low-permeable units. We have analyzed the experimental results using a numerical code and quantified......The efficiency of traditional soil venting or soil vapor extraction (SVE) highly depends on the architecture of the subsurface because imposed advective air flow tends to bypass low-permeable contaminated areas. Pneumatic SVE is a technique developed to enhance remediation efficiency...... level the pneumatic venting technology is superior to the traditional technique, and that the method is particularly efficient in cases where large permeability contrasts exist between soil units in the subsurface....

  12. Optimally Locating MARFORRES Units

    OpenAIRE

    Salmeron, Javier; Dell, Rob

    2015-01-01

    Javier Salmeron and Rob Dell The U.S. Marine Forces Reserve (USMCR, MARFORRES) is conducting realignment studies where discretionary changes may benefit from formal mathematical analysis. This study has developed an optimization tool to guide and/or support Commander, MARFORRES (CMFR) decisions. A prototype of the optimization tool has been tested with data from the units and Reserve Training Centers (RTCs) in the San Francisco, CA and Sacramento, CA areas. Prepared for: MARFORRES, POC:...

  13. LIDAR COMBINED SCANNING UNIT

    Directory of Open Access Journals (Sweden)

    V. V. Elizarov

    2016-11-01

    Full Text Available Subject of Research. The results of lidar combined scanning unit development for locating leaks of hydrocarbons are presented The unit enables to perform high-speed scanning of the investigated space in wide and narrow angle fields. Method. Scanning in a wide angular field is produced by one-line scanning path by means of the movable aluminum mirror with a frequency of 20Hz and amplitude of 20 degrees of swing. Narrowband scanning is performed along a spiral path by the deflector. The deflection of the beam is done by rotation of the optical wedges forming part of the deflector at an angle of ±50. The control function of the scanning node is performed by a specialized software product written in C# programming language. Main Results. This scanning unit allows scanning the investigated area at a distance of 50-100 m with spatial resolution at the level of 3 cm. The positioning accuracy of the laser beam in space is 15'. The developed scanning unit gives the possibility to browse the entire investigated area for the time not more than 1 ms at a rotation frequency of each wedge from 50 to 200 Hz. The problem of unambiguous definition of the beam geographical coordinates in space is solved at the software level according to the rotation angles of the mirrors and optical wedges. Lidar system coordinates are determined by means of GPS. Practical Relevance. Development results open the possibility for increasing the spatial resolution of scanning systems of a wide range of lidars and can provide high positioning accuracy of the laser beam in space.

  14. Radiation quantities and units

    International Nuclear Information System (INIS)

    1980-01-01

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

  15. United States rejoin ITER

    International Nuclear Information System (INIS)

    Roberts, M.

    2003-01-01

    Upon pressure from the United States Congress, the US Department of Energy had to withdraw from further American participation in the ITER Engineering Design Activities after the end of its commitment to the EDA in July 1998. In the years since that time, changes have taken place in both the ITER activity and the US fusion community's position on burning plasma physics. Reflecting the interest in the United States in pursuing burning plasma physics, the DOE's Office of Science commissioned three studies as part of its examination of the option of entering the Negotiations on the Agreement on the Establishment of the International Fusion Energy Organization for the Joint Implementation of the ITER Project. These were a National Academy Review Panel Report supporting the burning plasma mission; a Fusion Energy Sciences Advisory Committee (FESAC) report confirming the role of ITER in achieving fusion power production, and The Lehman Review of the ITER project costing and project management processes (for the latter one, see ITER CTA Newsletter, no. 15, December 2002). All three studies have endorsed the US return to the ITER activities. This historical decision was announced by DOE Secretary Abraham during his remarks to employees of the Department's Princeton Plasma Physics Laboratory. The United States will be working with the other Participants in the ITER Negotiations on the Agreement and is preparing to participate in the ITA

  16. United States advanced technologies

    International Nuclear Information System (INIS)

    Longenecker, J.R.

    1985-01-01

    In the United States, the advanced technologies have been applied to uranium enrichment as a means by which it can be assured that nuclear fuel cost will remain competitive in the future. The United States is strongly committed to the development of advanced enrichment technology, and has brought both advanced gas centrifuge (AGC) and atomic vapor laser isotope separation (AVLIS) programs to a point of significant technical refinement. The ability to deploy advanced technologies is the basis for the confidence in competitive future price. Unfortunately, the development of advanced technologies is capital intensive. The year 1985 is the key year for advanced technology development in the United States, since the decision on the primary enrichment technology for the future, AGC or AVLIS, will be made shortly. The background on the technology selection process, the highlights of AGC and AVLIS programs and the way to proceed after the process selection are described. The key objective is to maximize the sales volume and minimize the operating cost. This will help the utilities in other countries supply low cost energy on a reliable, long term basis. (Kako, I.)

  17. Primary metals extraction by liquid membranes

    International Nuclear Information System (INIS)

    Subramanian, K.N.

    1980-01-01

    The extraction of copper and uranium by liquid membranes is presented. The recovery of uranium from wet process phosphoric acid is described. The development of this process has progressed through three stages, firstly the chemistry of uranium extraction as it pertains to liquid membrane systems. This was followed by continuous extraction tests on fresh black acid and on aged acid. Results on a 1 litre/minute pilot plant demonstrated that the process could be operated with a minimum of feed pretreatment and about 90% of uranium could be extracted. The extraction of copper from copper leach liquors is also described. (U.K.)

  18. Extraction of uranyl sulfate with primary amine

    International Nuclear Information System (INIS)

    Mrnka, M.; Bizek, V.; Nekovar, P.; Cizevska, S.; Schroetterova, D.

    1984-01-01

    PRIMENE JM-T was used for extraction. Its composition was found to approach the general formula C 21 H 43 NH 2 . It was found that the extraction of uranyl sulfate is lower in case of a higher steady-state concentration of sulfuric acid in the aqueous phase. Extraction is accompanied with coextraction of water. The results obtained showed that uranyl sulfate passes into the organic phase by two mechanisms: extraction with amine sulfate and extraction with free amine. A mathematical description of the process was made based on the obtained results. (E.S.)

  19. Major dams of the United States, Geographic NAD83, USGS (2006) [dams00x020_USGS_2006

    Data.gov (United States)

    Louisiana Geographic Information Center — This map layer portrays major dams of the United States, including Puerto Rico and the U.S. Virgin Islands. The map layer was created by extracting dams 50 feet or...

  20. Wind Extraction for Natural Ventilation

    Science.gov (United States)

    Fagundes, Tadeu; Yaghoobian, Neda; Kumar, Rajan; Ordonez, Juan

    2017-11-01

    Due to the depletion of energy resources and the environmental impact of pollution and unsustainable energy resources, energy consumption has become one of the main concerns in our rapidly growing world. Natural ventilation, a traditional method to remove anthropogenic and solar heat gains, proved to be a cost-effective, alternative method to mechanical ventilation. However, while natural ventilation is simple in theory, its detailed design can be a challenge, particularly for wind-driven ventilation, which its performance highly involves the buildings' form, surrounding topography, turbulent flow characteristics, and climate. One of the main challenges with wind-driven natural ventilation schemes is due to the turbulent and unpredictable nature of the wind around the building that impose complex pressure loads on the structure. In practice, these challenges have resulted in founding the natural ventilation mainly on buoyancy (rather than the wind), as the primary force. This study is the initial step for investigating the physical principals of wind extraction over building walls and investigating strategies to reduce the dependence of the wind extraction on the incoming flow characteristics and the target building form.

  1. Injection and extraction for cyclotrons

    International Nuclear Information System (INIS)

    Heikkinen, P.

    1994-01-01

    External ion sources for cyclotrons are needed for polarised and heavy ions. This calls for injection systems, either radial or axial. Radial injection is also needed when a cyclotron works as a booster after another cyclotron or a linear accelerator (usually tandem). Requirements for injection differ from separated sector cyclotrons where there is plenty of room to house inflectors and/or strippers, to superconducting cyclotrons where the space is limited by a small magnet gap, and high magnetic field puts other limitations to the inflectors. Several extraction schemes are used in cyclotrons. Stripping injection is used for H - and also for heavy ions where the q/m ratio is usually doubled. For other cases, electric and magnetic deflection has to be used. To increase the turn separation before the first deflector, both resonant and non-resonant schemes are used. In this lecture, external injection systems are surveyed and some rules to thumb for injection parameters are given. Extraction schemes are also reviewed. (orig.)

  2. Solar Filament Extraction and Characterizing

    Science.gov (United States)

    Yuan, Yuan; Shih, F. Y.; Jing, J.; Wang, H.

    2010-05-01

    This paper presents a new method to extract and characterize solar filaments from H-alpha full-disk images produced by Big Bear Solar Observatory. A cascading Hough Transform method is designed to identify solar disk center location and radius. Solar disks are segmented from the background, and unbalanced illumination on the surface of solar disks is removed using polynomial surface fitting. And then a localized adaptive thresholding is employed to extract solar filament candidates. After the removal of small solar filament candidates, the remaining larger candidates are used as the seeds of region growing. The procedure of region growing not only connects broken filaments but also generate complete shape for each filament. Mathematical morphology thinning is adopted to produce the skeleton of each filament, and graph theory is used to prune branches and barbs to get the main skeleton. The length and the location of the main skeleton is characterized. The proposed method can help scientists and researches study the evolution of solar filament, for instance, to detect solar filament eruption. The presented method has already been used by Space Weather Research Lab of New Jersey Institute of Technology (http://swrl.njit.edu) to generate the solar filament online catalog using H-alpha full-disk images of Global H-alpha Network (http://swrl.njit.edu/ghn_web/).

  3. DESIGNING AN EVENT EXTRACTION SYSTEM

    Directory of Open Access Journals (Sweden)

    Botond BENEDEK

    2017-06-01

    Full Text Available In the Internet world, the amount of information available reaches very high quotas. In order to find specific information, some tools were created that automatically scroll through the existing web pages and update their databases with the latest information on the Internet. In order to systematize the search and achieve a result in a concrete form, another step is needed for processing the information returned by the search engine and generating the response in a more organized form. Centralizing events of a certain type is useful first of all for creating a news service. Through this system we are pursuing a knowledge - events from the Internet documents - extraction system. The system will recognize events of a certain type (weather, sports, politics, text data mining, etc. depending on how it will be trained (the concept it has in the dictionary. These events can be provided to the user, or it can also extract the context in which the event occurred, to indicate the initial form in which the event was embedded.

  4. 30 CFR 947.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 947.702 Section 947.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  5. 30 CFR 933.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 933.702 Section 933.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  6. 30 CFR 939.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 939.702 Section 939.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  7. 30 CFR 903.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 903.702 Section 903.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  8. 30 CFR 912.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 912.702 Section 912.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  9. 30 CFR 937.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 937.702 Section 937.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  10. 30 CFR 921.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 921.702 Section 921.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of the chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  11. 30 CFR 905.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 905.702 Section 905.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  12. 30 CFR 942.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 942.702 Section 942.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  13. 30 CFR 910.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 910.702 Section 910.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  14. 30 CFR 922.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 922.702 Section 922.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of Other...

  15. 30 CFR 941.702 - Exemption for coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Exemption for coal extraction incidental to the extraction of other minerals. 941.702 Section 941.702 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... other minerals. Part 702 of this chapter, Exemption for Coal Extraction Incidental to the Extraction of...

  16. 30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

  17. Supercritical fluid extraction of uranium from tissue paper matrix using organic extractants

    International Nuclear Information System (INIS)

    Kanekar, A.S.; Bhattacharyya, A.; Pathak, P.N.; Mohapatra, P.K.; Manchanda, V.K.

    2009-01-01

    Direct extraction of dried uranyl nitrate from tissue paper matrix was carried out using supercritical carbon dioxide modified with methanol solutions of extractants such as tri-n-butyl phosphate (TBP) and di-n-hexyl octanamide (DHOA)). The effects of temperature, pressure, extractant and nitric acid concentration on the extraction of uranyl ion were investigated. (author)

  18. Technical note: New applications for on-line automated solid phase extraction

    OpenAIRE

    MacFarlane, John D.

    1997-01-01

    This technical note explains the disadvantages of manual solid phase extraction (SPE) techniques and the benefits to be gained with automatic systems. The note reports on a number of general and highly specific applications using the Sample Preparation Unit OSP-2A.

  19. Dynamics and control of a heat pump assisted extractive dividing-wall column for bioethanol dehydration

    NARCIS (Netherlands)

    Patraşcu, Iulian; Bildea, Costin Sorin; Kiss, Anton A.

    Recently, a novel heat-pump-assisted extractive distillation process taking place in a dividing-wall column was proposed for bioethanol dehydration. This integrated design combines three distillation columns into a single unit that allows over 40% energy savings and low specific energy requirements

  20. 1/6TH SCALE STRIP EFFLUENT FEED TANK-MIXING RESULTS USING MCU SOLVENT

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, E

    2006-02-01

    The purpose of this task was to determine if mixing was an issue for the entrainment and dispersion of the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) solvent in the Defense Waste Processing Facility (DWPF) Strip Effluent Feed Tank (SEFT). The MCU strip effluent stream containing the Cs removed during salt processing will be transferred to the DWPF for immobilization in HLW glass. In lab-scale DWPF chemical process cell testing, mixing of the solvent in the dilute nitric acid solution proved problematic, and the Savannah River National Laboratory (SRNL) was requested to perform scaled SEFT mixing tests to evaluate whether the problem was symptomatic of the lab-scale set-up or of the solvent. The solvent levels tested were 228 and 235 ppm, which represented levels near the estimated DWPF solvent limit of 239 ppm in 0.001M HNO{sub 3} solution. The 239 ppm limit was calculated by Norato in X-CLC-S-00141. The general approach for the mixing investigation was to: (1) Investigate the use of fluorescent dyes to aid in observing the mixing behavior. Evaluate and compare the physical properties of the fluorescent dyed MCU solvents to the baseline Oak Ridge CSSX solvent. Based on the data, use the dyed MCU solvent that best approximates the physical properties. (2) Use approximately a 1/6th linear scale of the SEFT to replicate the internal configuration for DWPF mixing. (3) Determine agitator speed(s) for scaled testing based on the DWPF SEFT mixing speed. (4) Perform mixing tests using the 1/6th SEFT and determine any mixing issues (entrainment/dispersion, accumulation, adhesion) through visual observations and by pulling samples to assess uniformity. The mixing tests used MCU solvent fabricated at SRNL blended with Risk Reactor DFSB-K43 fluorescent dye. This dyed SRNL MCU solvent had equivalent physical properties important to mixing as compared to the Oak Ridge baseline solvent, blended easily with the MCU solvent, and provided an excellent visual aid.

  1. [Study on condition for extraction of arctiin from fruits of Arctium lappa using supercritical fluid extraction].

    Science.gov (United States)

    Dong, Wen-hong; Liu, Ben

    2006-08-01

    To study the feasibility of supercritical fluid extraction (SFE) for arctiin from the fruits of Arctium lappa. The extracts were analyzed by HPLC, optimum extraction conditions were studied by orthogonal tests. The optimal extraction conditions were: pressure 40 MPa, temperature 70 degrees C, using methanol as modifier carrier at the rate of 0.55 mL x min(-1), static extraction time 5 min, dynamic extraction 30 min, flow rate of CO2 2 L x min(-1). SFE has the superiority of adjustable polarity, and has the ability of extracting arctiin.

  2. Clinical evaluation of postradiation dental extraction

    International Nuclear Information System (INIS)

    Kusukawa, Jingo; Ohisi, Shinichiro; Kameyama, Tadamitsu; Yoshizumi, Munehiro; Hayabuchi, Naofumi

    1996-01-01

    Twenty-one patients who had undergone postradiation dental extraction were evaluated clinically. All patients had received irradiation for primary head and neck malignancies at doses ranging from 8 to 60 Gy (mean, 51.6 Gy). Time to dental extraction after irradiation ranged from 8 to 156 months (mean, 57.9 months). Of the 21 patients (80 teeth extracted, including 33 maxillary teeth and 47 mandibular teeth), one had delayed healing after wisdom tooth extraction due to postextraction irradiation. Thus, osteoradionecrosis after dental extraction did not develop. These results suggest that dental extraction after radiation is not contraindicated. To prevent complications, patients who have received radiation and require extractions should be cared for by oral and maxillofacial surgeons in close association with radiation oncologists. (author)

  3. Solvent extraction of noble metals by formazans

    International Nuclear Information System (INIS)

    Grote, M.; Hueppe, U.; Kettrup, A.

    1984-01-01

    The extraction properties of ion-pairs composed of quaternary ammonium cations and a sulphonated formazan were compared with those of an unsulphonated formazan, for various solvent media. In dichloromethane the combined system behaves as a 'coloured anion-exchanger', with displacement of the sulphonated formazan, whereas in toluene Pd(II) and Ag(I) are extracted as the metal formazan chelates from aqueous medium. The rates of extraction are remarkably higher than with the simple extractants. Because of the higher stability only the simple chelating extraction systems afford satisfactory separation of Pd(II) from excess of Pt(IV) and of Ag(I) from Cu(II). The extracted metals can be stripped and the extractant regenerated. (author)

  4. Extraction of some acids using aliphatic amines

    International Nuclear Information System (INIS)

    Matutano, L.

    1964-06-01

    Hydrochloric, nitric, sulphuric, perchloric, phosphoric, acetic and formic acids in aqueous solution (0.05 to 10 M) are extracted by amberlite LA2 and trilaurylamine in solution, 5 per cent by volume, in kerosene and xylene respectively. The extraction process consists of: neutralization of the amine salt; a 'molecular extraction', i.e. an extraction using an excess of acid with respect to the stoichiometry of the amine salt. According to the behaviour of the acid during the extraction, three groups may be distinguished: completely dissociated acids, carboxylic acids, phosphoric acid. This classification is also valid for the extraction of the water which occurs simultaneously with that of the acid. An extraction mechanism is put forward for formic acid and the formation constant of its amine salt is calculated. (author) [fr

  5. Inhibition of aluminum corrosion using Opuntia extract

    International Nuclear Information System (INIS)

    El-Etre, A.Y.

    2003-01-01

    The inhibitive action of the mucilage extracted from the modified stems of prickly pears, toward acid corrosion of aluminum, is tested using weight loss, thermometry, hydrogen evolution and polarization techniques. It was found that the extract acts as a good corrosion inhibitor for aluminum corrosion in 2.0 M HCl solution. The inhibition action of the extract was discussed in view of Langmuir adsorption isotherm. It was found that the adsorption of the extract on aluminum surface is a spontaneous process. The inhibition efficiency (IE) increases as the extract concentration is increased. The effect of temperature on the IE was studied. It was found that the presence of extract increases the activation energy of the corrosion reaction. Moreover, the thermodynamic parameters of the adsorption process were calculated. It was found also that the Opuntia extract provides a good protection to aluminum against pitting corrosion in chloride ion containing solutions

  6. The extraction of uranium from wet process phosphoric acid using a liquid surfactant membrane system

    International Nuclear Information System (INIS)

    Dickens, N.; Davies, G.A.

    1984-01-01

    A liquid membrane extraction process is examined for the extraction of uranium from wet process phosphoric acid. Uranium is present in the acid in concentrations up to 100 ppm which in principle makes it ideal for treatment with a membrane process. The membrane system studied is based on extraction using DEHPA-TOPO reagents which are contained within the organic phase of a water in oil emulsion. Formulations of the emulsion membrane system have been studied, the limitations of acid temperature, P 2 O 5 concentration and solid dispersed impurities in the acid have been studied in laboratory batch experiments and in a continuous pilot plant unit capable of treating 5l of concentrated acid per minute. Data from the pilot plant work has been used to develop a flowsheet for a commercial unit based on this process. (author)

  7. Extraction efficiency of hydrophilic and lipophilic antioxidants from lyophilized foods using pressurized liquid extraction and manual extraction.

    Science.gov (United States)

    Watanabe, Jun; Oki, Tomoyuki; Takebayashi, Jun; Takano-Ishikawa, Yuko

    2014-09-01

    The efficient extraction of antioxidants from food samples is necessary in order to accurately measure their antioxidant capacities. α-Tocopherol and gallic acid were spiked into samples of 5 lyophilized and pulverized vegetables and fruits (onion, cabbage, Satsuma mandarin orange, pumpkin, and spinach). The lipophilic and hydrophilic antioxidants in the samples were sequentially extracted with a mixed solvent of n-hexane and dichloromethane, and then with acetic acid-acidified aqueous methanol. Duplicate samples were extracted: one set was extracted using an automated pressurized liquid extraction apparatus, and the other set was extracted manually. Spiked α-tocopherol and gallic acid were recovered almost quantitatively in the extracted lipophilic and hydrophilic fractions, respectively, especially when pressurized liquid extraction was used. The expected increase in lipophilic oxygen radical absorbance capacity (L-ORAC) due to spiking with α-tocopherol, and the expected increase in 2,2-diphenyl-1-picrylhydrazyl radical scavenging activities and total polyphenol content due to spiking with gallic acid, were all recovered in high yield. Relatively low recoveries, as reflected in the hydrophilic ORAC (H-ORAC) value, were obtained following spiking with gallic acid, suggesting an interaction between gallic acid and endogenous antioxidants. The H-ORAC values of gallic acid-spiked samples were almost the same as those of postadded (spiked) samples. These results clearly indicate that lipophilic and hydrophilic antioxidants are effectively extracted from lyophilized food, especially when pressurized liquid extraction is used. © 2014 Institute of Food Technologists®

  8. Quality Parameters of Curcuma Longa L. Extracts by Supercritical Fluid Extraction (SFE) and Ultrasonic Assisted Extraction (UAE)

    International Nuclear Information System (INIS)

    Zaibunnisa Abdul Haiyee; Siti Hafsah Mohd Shah; Khudzir Ismail; Nooraain Hashim; Wan Iryani Wan Ismail

    2016-01-01

    Turmeric is one of the prominently use herbal plants due to its diverse beneficial effects especially in Indian medicine. The rhizome part of the turmeric contains valuable compounds which have been said to owe its antimicrobial effects, anti-cancer, anti-inflammatory and enhance wound healing. Due to its short-life span and perishable properties, the conversion of the rhizome into turmeric extract is desirable. Several methods have been used for extraction such as Soxhlet extraction and pressurized liquid extraction (PLE). However, these techniques are tedious, laborious, time consuming and involves the usage of toxic organic solvent, of which safeness of the end product is doubtful. In this study, a rapid, reliable and green extraction method of supercritical fluid extraction (SFE) and ultrasonic assisted extraction (UAE) were used. SFE without modifier has resulted in 0.0006 mg/ 100 g of curcuminoids concentration and 5.62 % of yield (dry weight basis). UAE using ethanol was able to produce significantly the highest yield (6.40 %, dry weight basis) and the highest curcuminoids concentration (0.1020 mg/ 100 g). However, SFE was able to produce extract that contain significantly higher major volatile compounds; tumerone, ar-turmerone and curlone. Therefore, this study proves that both extraction methods were able to produce high quality turmeric extract. (author)

  9. Chemical Profiling of Acalypha Indica Obtained from Supercritical Carbon Dioxide Extraction and Soxhlet Extraction Methods

    OpenAIRE

    Surangkana Chaichoowong; Jan Bernd Bol; Pornprapa Bol; Thomas Gamse; Malinee Sriariyanun

    2017-01-01

    Acalypha indica is a weed that grows in South-East Asia. It contains several valuable compounds that can be used for curing various diseases such as rheumatism, skin infection and blood dysentery. Here, the extraction of A. indica using Soxhlet extraction with two different solvents and supercritical CO2 extraction (SCE) with two different temperatures (40 and 60°C) was performed. In Soxhlet extraction, ethanol solvent provided the highest extraction yield of 34.36%. For SCE, the increased te...

  10. Extraction and Quantitative HPLC Analysis of Coumarin in Hydroalcoholic Extracts of Mikania glomerata Spreng: ("guaco" Leaves

    Directory of Open Access Journals (Sweden)

    Celeghini Renata M. S.

    2001-01-01

    Full Text Available Methods for preparation of hydroalcoholic extracts of "guaco" (Mikania glomerata Spreng. leaves were compared: maceration, maceration under sonication, infusion and supercritical fluid extraction. Evaluation of these methods showed that maceration under sonication had the best results, when considering the ratio extraction yield/extraction time. A high performance liquid chromatography (HPLC procedure for the determination of coumarin in these hydroalcoholic extracts of "guaco" leaves is described. The HPLC method is shown to be sensitive and reproducible.

  11. Inhibitory Effects of Pterodon emarginatus Bean Oil and Extract on Staphylococcus aureus.

    Science.gov (United States)

    Mendes, V S; Sant'Anna, J B; Oliveira, S C C; Maldonade, Iriani Rodrigues; Machado, Eleuza Rodrigues

    2017-01-01

    Pterodon emarginatus is a tree of the Brazilian Savannah. The beans of this tree are used in folk medicine as anti-inflammatory preparations, especially for infections caused by Staphylococcus aureus . These bacteria can cause simple infections or serious illnesses such as pneumonia, meningitis, endocarditis, toxic shock syndrome, septicemia, and others. This study had the goal of verifying the effect of the essential oil (OE) from P. emarginatus on the inhibition of S. aureus in culture medium, i.e., " in vitro " tests. The vegetable material was cut and crushed with a press. The OE was obtained by extraction using hexane, alcohol, and water. The P. emarginatus extracts obtained were used to evaluate the antimicrobial effect on S. aureus (ATCC 25923) by tests of well diffusion, disc diffusion, and microdilution. The strain used in the assays was maintained in brain heart infusion broth and nutrient agar until testing. Afterward, the bacteria were spread on agar plates with Mueller-Hinton agar medium. In the wells and on the paper discs, the OE suspensions were placed in the following volumes: 10, 15, 20, 25, 30, 40, and 80 μL and subsequently they were incubated at 35°C ± 2°C. After 24 h, the number of colony-forming unit was determined. Pure OE and hydroalcoholic extract inhibited the growth of S. aureus , while aqueous extract had no effect on bacterial growth in all microbial methods used. Thus, the present study showed the potential of sucupira-based extracts against S. aureus growth, opening new perspectives for the evaluation of these bioactive compounds as phytopharmaceutical products. Plant extract act as antimicrobials to prevent and reduce bacterial contaminationBeans of Pterodon emarginatus has antibacterial propertiesExtraction with different solvents might implicate on the rate of bacterial deathThe effect of different microbiological methods (well diffusion, disc diffusion and microdilution) was evaluated on reducing CFUThe results showed by MBC

  12. Changing perspectives on resource extraction.

    Science.gov (United States)

    Gibson, Hazel; Stewart, Iain; Pahl, Sabine; Stokes, Alison

    2015-04-01

    Over the last century, resource extraction in the UK has changed immeasurably; from relatively small-scale, manually-operated facilities to the larger technological advanced sites that exist today. The communities that live near these sites have also changed, from housing workers that were as much of a resource as the geological material, to local residents who are environmentally literate and strongly value their landscape. Nowadays great pressure is put on the extractive industry to work in both environmentally sustainable and socially ethical ways, but how does this impact upon the local population? How do communities perceive the resource extraction that neighbours them? And is this perception rooted in a general understanding of geology and the subsurface? To explore resident's perceptions of the geological environment, three villages in the southwest of England have been investigated, using a mixed-methods mental models approach. The villages were selected as each has a different geological setting, both commercially and culturally. The first village has a strong historical geological identity, but little current geological activity. The second village has a large tungsten mine in the process of beginning production. The third village has no obvious cultural or commercial relationships with geology and acts as the control site. A broad sample from each of the three villages was qualitatively interviewed, the results of which were analyzed using an emergent thematic coding scheme. These qualitative results were then modelled using Morgan et al's mental models method (2002) and tested using a quantitative questionnaire. The results of this mixed method approach reveals the principal perceptions (or mental models) of residents in these three villages. The villages each present a different general perception of resource exploitation, which appears to be culturally driven, with the first village having the most positive correlations. These mental models are

  13. The Military Emergency Unit

    International Nuclear Information System (INIS)

    Gonzalez Requena, J. M.

    2007-01-01

    One of the most justified and pressing demands that society makes of the State, requiring a fast, forceful and effective response, is that it guarantees the safety of people and their assets when a disaster seriously endangers them. At the proposal of the President of the Government, the Cabinet of Ministers, in its meeting held on October 7, 2005, agreed to create the Military Emergency Unit, known since the as the UME. Its mission is to intervene anywhere in the national territory when the President of the Government, or the Minister to whom he delegates, so decides in order to assure the safety and welfare of citizens in cases of serious risk, disaster, catastrophe or any other public need. The UME is organically incorporated into the Ministry of Defense and its actions may be supported with all the available human and material needs of the Armed Forces. Availability and effectiveness, with calmness and humility, have characterized the early actions of the Military Emergency Unit and are the guidelines for future action. The first steps of this military unit have focused on a clear goal: collaboration and participation in situations whose seriousness requires the coordination of different forces in order to immediately respond to them. The UME is the States tool to join forces and, with other administration and institutions, help to rapidly and effectively deal with emergencies. It has taken its first step and achieved the capacity specified in the UME Operations Order for 2007. The 150 men and women per battalion, plus the 80 in the Gando detachment, are on active duty and have sufficient material means to deploy, if necessary and when requested by the regions, town councils an other administrative bodies, to help in the extinction of forest fires. (Author)

  14. Unit for air decontamination

    International Nuclear Information System (INIS)

    Mariano H, E.

    1991-02-01

    To fulfill the applicable requirements of safety to the ventilation systems in nuclear facilities, it is necessary to make a cleaning of the air that hurtles to the atmosphere. For that which was designed and it manufactured an unit for decontamination of the air for the Pilot plant of production of Nuclear Fuel that this built one with national parts, uses Hepa national filters and the design can adapt for different dimensions of filters, also can be added a lodging for a prefilter or to adopt two Hepa filters. (Author)

  15. Waste Water Treatment Unit

    International Nuclear Information System (INIS)

    Ramadan, A.E.K.

    2004-01-01

    A wastewater treatment plant to treat both the sanitary and industrial effluent originated from process, utilities and off site units of the refinery is described. The purpose is to obtain at the end of the treatment plant, a water quality that is in compliance with contractual requirements and relevant environmental regulations. first treatment (pretreatment). Primary de-oiling, Equalization, Neutralization, Secondary de-oiling. Second treatment (Biological), The mechanism of BOD removal, Biological flocculation, Nutrient requirements, Nitrification, De-nitrification, Effect of temperature, Effect of ph, Toxicity

  16. Applied Meteorology Unit (AMU)

    Science.gov (United States)

    Bauman, William; Crawford, Winifred; Barrett, Joe; Watson, Leela; Wheeler, Mark

    2010-01-01

    This report summarizes the Applied Meteorology Unit (AMU) activities for the first quarter of Fiscal Year 2010 (October - December 2009). A detailed project schedule is included in the Appendix. Included tasks are: (1) Peak Wind Tool for User Launch Commit Criteria (LCC), (2) Objective Lightning Probability Tool, Phase III, (3) Peak Wind Tool for General Forecasting, Phase II, (4) Upgrade Summer Severe Weather Tool in Meteorological Interactive Data Display System (MIDDS), (5) Advanced Regional Prediction System (ARPS) Data Analysis System (ADAS) Update and Maintainability, (5) Verify 12-km resolution North American Model (MesoNAM) Performance, and (5) Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) Graphical User Interface.

  17. Extracting information from multiplex networks

    Science.gov (United States)

    Iacovacci, Jacopo; Bianconi, Ginestra

    2016-06-01

    Multiplex networks are generalized network structures that are able to describe networks in which the same set of nodes are connected by links that have different connotations. Multiplex networks are ubiquitous since they describe social, financial, engineering, and biological networks as well. Extending our ability to analyze complex networks to multiplex network structures increases greatly the level of information that is possible to extract from big data. For these reasons, characterizing the centrality of nodes in multiplex networks and finding new ways to solve challenging inference problems defined on multiplex networks are fundamental questions of network science. In this paper, we discuss the relevance of the Multiplex PageRank algorithm for measuring the centrality of nodes in multilayer networks and we characterize the utility of the recently introduced indicator function Θ ˜ S for describing their mesoscale organization and community structure. As working examples for studying these measures, we consider three multiplex network datasets coming for social science.

  18. Adaptive web data extraction policies

    Directory of Open Access Journals (Sweden)

    Provetti, Alessandro

    2008-12-01

    Full Text Available Web data extraction is concerned, among other things, with routine data accessing and downloading from continuously-updated dynamic Web pages. There is a relevant trade-off between the rate at which the external Web sites are accessed and the computational burden on the accessing client. We address the problem by proposing a predictive model, typical of the Operating Systems literature, of the rate-of-update of each Web source. The presented model has been implemented into a new version of the Dynamo project: a middleware that assists in generating informative RSS feeds out of traditional HTML Web sites. To be effective, i.e., make RSS feeds be timely and informative and to be scalable, Dynamo needs a careful tuning and customization of its polling policies, which are described in detail.

  19. Nickel extraction from nickel matte

    Science.gov (United States)

    Subagja, R.

    2018-01-01

    In present work, the results of research activities to make nickel metal from nickel matte are presented. The research activities were covering a) nickel matte characterization using Inductively Couple plasma (ICP), Electron Probe Micro Analyzer (EPMA) and X-Ray Diffraction (XRD), b) nickel matte dissolution process to dissolve nickel from nickel matte into the spent electrolyte solutions that contains hydrochloric acid, c) purification of nickel chloride leach solution by copper cementation process to remove copper using nickel matte, selective precipitation process to remove iron, solvent extraction using Tri normal octyl amine to separate cobalt from nickel chloride solutions and d) Nickel electro winning process to precipitate nickel into the cathode surface from purified nickel chloride solution by using direct current. The research activities created 99, 72 % pure nickel metal as the final product of the process.

  20. Incremental Observer Relative Data Extraction

    DEFF Research Database (Denmark)

    Bukauskas, Linas; Bøhlen, Michael Hanspeter

    2004-01-01

    The visual exploration of large databases calls for a tight coupling of database and visualization systems. Current visualization systems typically fetch all the data and organize it in a scene tree that is then used to render the visible data. For immersive data explorations in a Cave...... or a Panorama, where an observer is data space this approach is far from optimal. A more scalable approach is to make the observer-aware database system and to restrict the communication between the database and visualization systems to the relevant data. In this paper VR-tree, an extension of the R......-tree, is used to index visibility ranges of objects. We introduce a new operator for incremental Observer Relative data Extraction (iORDE). We propose the Volatile Access STructure (VAST), a lightweight main memory structure that is created on the fly and is maintained during visual data explorations. VAST...

  1. Clinical utility of curcumin extract.

    Science.gov (United States)

    Asher, Gary N; Spelman, Kevin

    2013-01-01

    Turmeric root has been used medicinally in China and India for thousands of years. The active components are thought to be the curcuminoids, primarily curcumin, which is commonly available worldwide as a standardized extract. This article reviews the pharmacology of curcuminoids, their use and efficacy, potential adverse effects, and dosage and standardization. Preclinical studies point to mechanisms of action that are predominantly anti-inflammatory and antineoplastic, while early human clinical trials suggest beneficial effects for dyspepsia, peptic ulcer, inflammatory bowel disease, rheumatoid arthritis, osteoarthritis, uveitis, orbital pseudotumor, and pancreatic cancer. Curcumin is well-tolerated; the most common side effects are nausea and diarrhea. Theoretical interactions exist due to purported effects on metabolic enzymes and transport proteins, but clinical reports do not support any meaningful interactions. Nonetheless, caution, especially with chemotherapy agents, is advised. Late-phase clinical trials are still needed to confirm most beneficial effects.

  2. Topic extraction from adverbial clauses

    Directory of Open Access Journals (Sweden)

    Carlos Rubio Alcalá

    2016-06-01

    Full Text Available This paper offers new data to support findings about Topic extraction from adverbial clauses. Since such clauses are strong islands, they should not allow extraction of any kind, but we show here that if the appropriate conditions are met, Topics of the CLLD kind in Romance can move out of them. We propose that two conditions must be met for such movement to be possible: the first is that the adverbial clause must have undergone topicalisation in the first place; the second is that the adverbial clause is inherently topical from a semantic viewpoint. Contrast with other language families (Germanic, Quechua and Japanese is provided and the semantic implications of the proposal are briefly discussed. Keywords: topicalisation; Clitic Left Dislocation; syntactic islands; adverbial clauses Este artículo ofrece nuevos datos sobre la extracción de Tópicos desde oraciones subordinadas adverbiales. Dado que dichas oraciones son islas fuertes, no deberían permitir extracción de ningún tipo, pero mostramos que si se dan las condiciones apropiadas, los Tópicos del tipo CLLD en lenguas románicas pueden desplazarse fuera de ellas. Proponemos que se deben cumplir dos condiciones para que ese movimiento sea posible: la primera es que la propia subordinada adverbial se haya topicalizado en primer lugar; la segunda es que la subordinada adverbial sea inherentemente un Tópico desde el punto de vista semántico. Proporcionamos también algunos contrastes con otras familias lingüísticas (germánica, quechua y japonés y se discuten brevemente las implicaciones semánticas de la propuesta. Palabras clave: topicalización; dislocación a la izquierda con clítico; islas sintácticas; oraciones adverbiales

  3. Extraction of uranium from seawater

    International Nuclear Information System (INIS)

    Kanno, M.

    1977-01-01

    The nuclear power generation is thought to be very important in Japan. However, known domestic uranium resources in Japan are very rare. So, extraction of uranium from sea water have been carried out since 1962 at Japan Tobacco and Salt Public Corporation. There are a number of results obtained also by Kyoto University, Shikoku Govenment Industrial Research Institute, Tokyo University and others. In order to investigate the technical and economical feasibility of extraction of uranium and other resources from sea water, a research program was started in fiscal 1975, sponsored by the Ministry of International Trade and Industry with the budget of about $440,000. In this program, the conceptional design of two types of model plants, the ''column type'' and the ''tidal type'' was drawn on the design bases set up with available information. It was found that there has been several problems waiting solution, but there were no technically fatal problems. Adsorption tests were carried out with adsorbents of more than eleven types, including titanium hydroxide, and it was found that titanium hydroxide made by titanyl surphate and urea had the largest adsorption capacity of uranium among them. Elution experiments were performed only with ammonium carbonate and the efficiency at the temperature of 60 0 C showed three times higher than that of 20 0 C. A few long term column operation was conducted, mainly with the adsorbent of granulated titanium hydroxide for 15-60 days. The maximum yield of uranium throughout the adsorption and elution operation was over 20% and macimum concentration of uranium in eluate was 7 ppm

  4. Solvent extraction of Southern US tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Penney, W.R.

    1990-01-01

    The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

  5. Application of enzymatic methods for chia (Salvia hispanica L oil extraction

    Directory of Open Access Journals (Sweden)

    Norma Ciau-Solís

    2016-07-01

    Full Text Available Aim. The aim was to evaluate the use of different enzymatic treatments on the oil extraction yield from Chia (Salvia hispanica L. seeds Methods. Enzymatic extraction was performed by treating of whole and degummed chia flours with different conditions of enzyme concentration, pH and temperature. Commercial enzymes were employed: Viscozyme LTM (endo-1,3 (4-betaglucanase derived from Aspergillus aculeatus, with 100 FBG g (Beta Glucanase-unit Fungal and Neutrase0.8LTM, neutral protease with 0.8 AU-NH/g of activity, derived from Bacillus amyloliquefaciens. Results. All treatments of enzymatic oil extraction were different (P <0.05 and the maximum oil yield obtained was 9.35%. Conclusion. Oil extraction using enzymatic methods is not a viable for chia seed

  6. Gallbladder shape extraction from ultrasound images using active contour models.

    Science.gov (United States)

    Ciecholewski, Marcin; Chochołowicz, Jakub

    2013-12-01

    Gallbladder function is routinely assessed using ultrasonographic (USG) examinations. In clinical practice, doctors very often analyse the gallbladder shape when diagnosing selected disorders, e.g. if there are turns or folds of the gallbladder, so extracting its shape from USG images using supporting software can simplify a diagnosis that is often difficult to make. The paper describes two active contour models: the edge-based model and the region-based model making use of a morphological approach, both designed for extracting the gallbladder shape from USG images. The active contour models were applied to USG images without lesions and to those showing specific disease units, namely, anatomical changes like folds and turns of the gallbladder as well as polyps and gallstones. This paper also presents modifications of the edge-based model, such as the method for removing self-crossings and loops or the method of dampening the inflation force which moves nodes if they approach the edge being determined. The user is also able to add a fragment of the approximated edge beyond which neither active contour model will move if this edge is incomplete in the USG image. The modifications of the edge-based model presented here allow more precise results to be obtained when extracting the shape of the gallbladder from USG images than if the morphological model is used. © 2013 Elsevier Ltd. Published by Elsevier Ltd. All rights reserved.

  7. Hemimorphite Ores: A Review of Processing Technologies for Zinc Extraction

    Science.gov (United States)

    Chen, Ailiang; Li, Mengchun; Qian, Zhen; Ma, Yutian; Che, Jianyong; Ma, Yalin

    2016-10-01

    With the gradual depletion of zinc sulfide ores, exploration of zinc oxide ores is becoming more and more important. Hemimorphite is a major zinc oxide ore, attracting much attention in the field of zinc metallurgy although it is not the major zinc mineral. This paper presents a critical review of the treatment for extraction of zinc with emphasis on flotation, pyrometallurgical and hydrometallurgical methods based on the properties of hemimorphite. The three-dimensional framework structure of hemimorphite with complex linkage of its structural units lead to difficult desilicification before extracting zinc in the many metallurgical technologies. It is found that the flotation method is generally effective in enriching zinc minerals from hemimorphite ores into a high-grade concentrate for recovery of zinc. Pure zinc can be produced from hemimorphite or/and willemite with a reducing reagent, like methane or carbon. Leaching reagents, such as acid and alkali, can break the complex structure of hemimorphite to release zinc in the leached solution without generation of silica gel in the hydrometallurgical process. For optimal zinc extraction, combing flotation with pyrometallurgical or hydrometallurgical methods may be required.

  8. Bioactivity of Neem (Azadirachta indica) callus extract

    International Nuclear Information System (INIS)

    Ahmed, I.M.

    2008-04-01

    This study was conducted in order to explore the possibility of utilizing plant tissue culture techniques for production of secondary metabolites from callus culture of Azadirachta indica (Neem) and to investigate the bioactivity of the established callus extract in comparison with the extract from the intact leaves. The presence of secondary metabolites in the extracts was detected by Thin Layer Chromatography (TLC). Both the callus and leaf extracts eluted five fraction of compounds and it were observed that callus extract had a good resolution. various extract concentration (5.10. and 20 mg/ml) were determined for the rate and extent of inhibition kinetics against staphylococcus aureus. Escherichia coli, and candida albicans. Results showed that callus extract of A. indica wiped out all viable cells of C. albicans within 18 hours and the subsequent concentration 5 and 10 mg/ m1 retard the growth after 24 h. A higher concentration of 20 mg/ ml had the same effect on S. aureus after 6 h and the E. coli cells were completely inhibited by the extracts after 24 h. Similar kinetics were showed by leaf extract but in slight rate as compared to the callus extract. In general both extract posses antimicrobial activity with notable efficient rates. For assaying of the inhibitory effect on some phyto pathogens the effect of different concentrations of the callus and leaf extracts on the radial growth of Drechslera rostrata. Fusarium oxysporum and Alterneria alternata were in vitro assessed. Obvious inhibitory effect was observed on the mycelia radial growth of the three treated fungi. The level of inhibition increased with the increase of te extract concentration. The maximum inhibitory effect (84%) was recorded with Drechslera rostrata when inoculated in media contain 20 mg/ ml of callus while the inhibition rate of mycelia growth of the same species reaches 61% when inoculated in a medium contain the same concentration of the neem leaf extract. The subsequent

  9. Mechanical Extraction of Power From Ocean Currents and Tides

    Science.gov (United States)

    Jones, Jack; Chao, Yi

    2010-01-01

    time of high power demand. Multiple submerged turbine/pump units could be positioned across a channel to extract more power than could be extracted by a single unit. In that case, the pressurized flows in their output pipes would be combined, via check valves, into a wider pipe that would deliver the combined flow to a power-generating or pumped-storage facility.

  10. The Hydrometallurgical Extraction and Recovery of High-Purity Silver

    Science.gov (United States)

    Hoffmann, James E.

    2012-06-01

    With the continuous reduction in the availability of extractive metallurgical curricula in colleges and universities, the concern has in part been from where will the next generation of extractive metallurgists come? One objective of this article is to emphasize the fact that extractive metallurgy is, in fact, one of many areas of chemical engineering technology. Thus, although the extractive metallurgist may have disappeared in name, its activity is alive and well, subsumed in the field of chemical engineering. One goal of this lecture is to demonstrate the applicability of chemical engineering principles to what is typically considered "the field of extractive metallurgy." Two processes will be described that have supplanted typical pyrometallurgical fire refining of precious metals, particularly silver. The origins of fire refining can be traced back to biblical times. There are numerous references to it in the old testament: Ezekiel 22:20, "As men gather silver and bronze and iron and lead and tin into a furnace to blow the fire upon it in order melt it"; Jeremiah 6:29, "The bellows blow fiercely; the lead is consumed by the fire; in vain the refining goes on"; and Malachi 3:2 (The Oxford Annotated Bible with the Apocrypha), "For he is like a refiners fire." Many references to it will also be found in "De Re Metallurgica" and as well in Lazarus Ercker's 1574 Manual "Treatise on Ores and Refining." Today, fire refining has been improved greatly by innovative furnace design, new fluxing technologies, and the improved use of oxygen. However, fundamentally, the process chemistry has not changed much in the last millennium. Illustrations of hydrometallurgical processing of silver-bearing inputs will be provided by the treatment of sulfated silver-bearing materials and chlorinated slimes. The first of these technologies will be described briefly as practiced by the Phelps Dodge Refining Corporation for several years. The second, the treatment of silver chloride

  11. An ISOLDE target unit

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    A good dozen different targets are available for ISOLDE, made of different materials and equipped with different kinds of ion-sources, according to the needs of the experiments. Each separator (GPS: general purpose; HRS: high resolution) has its own target. Because of the high radiation levels, robots effect the target changes, about 80 times per year. In the standard unit shown in picture _01, the target is the cylindrical object in the front. It contains uranium-carbide kept at a temperature of 2200 deg C, necessary for the isotopes to be able to escape. At either end, one sees the heater current leads, carrying 700 A. The Booster beam, some 3E13 protons per pulse, enters the target from left. The evaporated isotope atoms enter a hot-plasma ion source (the black object behind the target). The whole unit sits at 60 kV potential (pulsed in synchronism with the arrival of the Booster beam) which accelerates the ions (away from the viewer) towards one of the 2 separators.

  12. The United Kingdom

    International Nuclear Information System (INIS)

    Jones, P.M.S.

    1987-01-01

    The history of nuclear development in the United Kingdom is traced, together with the factors (eg electricity demand, fossil fuel prices, political policy) that have influenced policy choices. Many of the research establishments and the fissile material production plants were established in the late 1940s. In these early years the civil and military development programmes were not separate. The initial growth period was in the 1950s when the plan was to build twelve reactors in three groups of four over ten years. The first were to be Magnox type reactors. This was trebled in 1957 and the advanced gas cooled reactor was developed. The Windscale fire in 1957 affected confidence in the nuclear programme. However, five AGR twin-reactor stations were ordered in 1964. These ran into construction problems and delay and it was not until 1980 that more new units were contemplated. The plan then was to build a pressurized water reactor at Sizewell-B. A delay to allow for the public inquiry put back the start of this until 1987 with commissioning planned for 1994. A list of the UK nuclear power stations is given and their operating performance discussed. The present situation and future prospects for nuclear power are reviewed. (U.K.)

  13. Modeling and prediction of extraction profile for microwave-assisted extraction based on absorbed microwave energy.

    Science.gov (United States)

    Chan, Chung-Hung; Yusoff, Rozita; Ngoh, Gek-Cheng

    2013-09-01

    A modeling technique based on absorbed microwave energy was proposed to model microwave-assisted extraction (MAE) of antioxidant compounds from cocoa (Theobroma cacao L.) leaves. By adapting suitable extraction model at the basis of microwave energy absorbed during extraction, the model can be developed to predict extraction profile of MAE at various microwave irradiation power (100-600 W) and solvent loading (100-300 ml). Verification with experimental data confirmed that the prediction was accurate in capturing the extraction profile of MAE (R-square value greater than 0.87). Besides, the predicted yields from the model showed good agreement with the experimental results with less than 10% deviation observed. Furthermore, suitable extraction times to ensure high extraction yield at various MAE conditions can be estimated based on absorbed microwave energy. The estimation is feasible as more than 85% of active compounds can be extracted when compared with the conventional extraction technique. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Extraction of functional ingredients from spinach (Spinacia oleracea L.) using liquid solvent and supercritical CO₂ extraction.

    Science.gov (United States)

    Jaime, Laura; Vázquez, Erika; Fornari, Tiziana; López-Hazas, María del Carmen; García-Risco, Mónica R; Santoyo, Susana; Reglero, Guillermo

    2015-03-15

    In this work three different techniques were applied to extract dry leaves of spinach (Spinacia oleracea): solid-liquid extraction (SLE), pressurised liquid extraction (PLE) and supercritical fluid extraction (SFE) to investigate the influence of extraction solvent and technique on extracts composition and antioxidant activity. Moreover, the influence of carotenoids and phenolic compounds on the antioxidant and anti-inflammatory activities of spinach extracts was also studied. The higher concentrations of carotenoids and the lower content of phenolic compounds were observed in the supercritical CO₂ extracts; whereas water and/or ethanol PLE extracts presented low amounts of carotenoids and the higher concentrations of phenolic compounds. PLE extract with the highest content of phenolic compounds showed the highest antioxidant activity, although SFE carotenoid rich extract also showed a high antioxidant activity. Moreover, both extracts presented an important anti-inflammatory activity. PLE seems to be a good technique for the extraction of antioxidant and anti-inflammatory compounds from spinach leaves. Moreover, spinach phenolic compounds and carotenoids present a high antioxidant activity, whereas spinach carotenoids seem to show a higher anti-inflammatory activity than phenolic compounds. It is worth noting that of our knowledge this is the first time the anti-inflammatory activity of lipophilic extracts from spinach leaves is reported. © 2014 Society of Chemical Industry.

  15. Development of polysulfonic composite beads for extraction and separation of rare earths

    International Nuclear Information System (INIS)

    Yadav, K.K.; Singh, D.K.; Singh, H.; Varshney, L.

    2012-01-01

    Solvent extraction technology has been extensively applied to the practical separation of rare earth metals. Among the extractants commonly employed at present, di(2-ethylhexyl) hydrogen phosphate (D2EHPA) and 2-ethylhexyl hydrogen 2-ethylhexylphosphonate (PC-88A) are known to have advantages of high separation efficiency for rate earth metals and of low solubility in water. However, separation via solvent extraction requires multistage cycles of extraction and back extraction in order to attain favorable separation. Novel adsorbents such as solvent impregnated resins (SIRS), metal-imprinted polymers and microcapsules containing extractants might have wide applicability due to their characteristics having respective advantages of solvent extraction and the ion-exchange technique. In the present work, polymeric composite material impregnating extractants such as D2EHPA, PC88A and DNPPA were prepared and tested for rare earths recovery from chloride medium. Exploratory tests were conducted with Yttrium (taking as representative of rare earths) to evaluate the suitability of the composite beads having D2EHPA, PC88A and DNPPA. Preparation of beads comprises of following steps. Initially, a polymer solutions containing suitable amount of polymer (5 to 15% with 1% water soluble additive) in N-methyl pyrrolidone (NMP) was prepared. The above prepared solutions were then mixed with organophosphorus type of extractant namely D2EHPA, PC88A and di nonyl phenyl phosphoric acid (DNPPA). This polymer solution was gradually dropped drop wise into the water bath through a syringe needle. In the preparation, the temperature of the water was kept constant using a thermostatic unit. As as polymeric drop comes in contact with water due to phase inversion, polysulfonic microcapsules impregnated with the extractant were obtained, these microcapsules were immersed and stabilized in the water bath for 24 h

  16. A hybrid approach for robust multilingual toponym extraction and disambiguation

    NARCIS (Netherlands)

    Habib, Mena Badieh; van Keulen, Maurice

    Toponym extraction and disambiguation are key topics recently addressed by fields of Information Extraction and Geographical Information Retrieval. Toponym extraction and disambiguation are highly dependent processes. Not only toponym extraction effectiveness affects disambiguation, but also

  17. Caffeine adsorption of montmorillonite in coffee extracts.

    Science.gov (United States)

    Shiono, Takashi; Yamamoto, Kenichiro; Yotsumoto, Yuko; Yoshida, Aruto

    2017-08-01

    The growth in health-conscious consumers continues to drive the demand for a wide variety of decaffeinated beverages. We previously developed a new technology using montmorillonite (MMT) in selective decaffeination of tea extract. This study evaluated and compared decaffeination of coffee extract using MMT and activated carbon (AC). MMT adsorbed caffeine without significant adsorption of caffeoylquinic acids (CQAs), feruloylquinic acids (FQAs), dicaffeoylquinic acids (di-CQAs), or caffeoylquinic lactones (CQLs). AC adsorbed caffeine, chlorogenic acids (CGAs) and CQLs simultaneously. The results suggested that the adsorption selectivity for caffeine in coffee extract is higher in MMT than AC. The caffeine adsorption isotherms of MMT in coffee extract fitted well to the Langmuir adsorption model. The adsorption properties in coffee extracts from the same species were comparable, regardless of roasting level and locality of growth. Our findings suggest that MMT is a useful adsorbent in the decaffeination of a wide range of coffee extracts.

  18. New extraction chromatographic material for rhenium separation

    International Nuclear Information System (INIS)

    Lucanikova, M.; Czech Technical University, Prague; Kucera, J.; Czech Technical University, Prague; Sebesta, F.

    2008-01-01

    Three types of the extraction chromatographic materials, composed from Aliquat R 336 deposited in the polyacrylonitrile (PAN) beads and prepared by different procedures, were compared for extraction of rhenium. The best properties were exhibited when the solid extractant was prepared by impregnation of the ready-made PAN beads. Solid extractant prepared by direct coagulation of the beads from the suspension of Aliquat R 336 in solution of PAN in nitric acid differs only by lower capacity in dynamic conditions. Material prepared from the PAN solution in dimethylsulfoxide was the worst because Aliquat R 336 was washed out from the beads during coagulation of the polymer and the extraction capacity was low. As it is shown, the first two solid extractants are fully comparable with the commercial TEVA Resin. (author)

  19. Extraction of scandium by organic substance melts

    International Nuclear Information System (INIS)

    Gladyshev, V.P.; Lobanov, F.I.; Zebreva, A.I.; Andreeva, N.N.; Manuilova, O.A.; Il'yukevich, Yu.A.

    1984-01-01

    Regularities of scandium extraction by the melts of octadecanicoic acid, n-carbonic acids of C 17 -C 20 commerical fraction and mixtures of tributylphosphate (TBP) with paraffin at (70+-1) deg C have been studied. The optimum conditions for scandium extraction in the melt of organic substances are determined. A scheme of the extraction by the melts of higher carbonic acids at ninitial metal concentrations of 10 -5 to 10 -3 mol/l has been suggested. The scandium compound has been isolated in solid form, its composition having been determined. The main advantages of extraction by melts are as follows: a possibility to attain high distribution coefficients, distinct separation of phases after extraction, the absence of emulsions, elimination of employing inflammable and toxic solvents, a possibility of rapid X-ray fluorescence determinatinon of scandium directly in solid extract

  20. Extraction of fluoride metal complexes by octanols

    International Nuclear Information System (INIS)

    Baklanova, I.V.; Nikolaev, A.I.; Il'in, E.G.; Majorov, V.G.

    2005-01-01

    The extraction of niobium(V) and tantalum(V) by octanols, including 1-octanol, 2-octanol, and iso-octanol (2-ethylhexanol), was studied. The composition of the octanols and their solubility in various aqueous solutions were evaluated. The capacity of the octanols for tantalum(V) and niobium(V), the extraction properties of the octanols, the viscosity of extracts under conditions of metal fluoride extraction, and the temperature dependence of the viscosity of the octanols were studied. The composition of the extracted complexes was studied by IR and NMR spectroscopy and chemical analysis, and the hydration-solvation mechanism of the extraction of tantalum(V) and niobium(V) was supported [ru

  1. Functional unit for a processor

    NARCIS (Netherlands)

    Rohani, A.; Kerkhoff, Hans G.

    2013-01-01

    The invention relates to a functional unit for a processor, such as a Very Large Instruction Word Processor. The invention further relates to a processor comprising at least one such functional unit. The invention further relates to a functional unit and processor capable of mitigating the effect of

  2. Design of hydraulic recuperation unit

    Directory of Open Access Journals (Sweden)

    Jandourek Pavel

    2016-01-01

    Full Text Available This article deals with design and measurement of hydraulic recuperation unit. Recuperation unit consist of radial turbine and axial pump, which are coupled on the same shaft. Speed of shaft with impellers are 6000 1/min. For economic reasons, is design of recuperation unit performed using commercially manufactured propellers.

  3. Snakes: An Integrated Unit Plan.

    Science.gov (United States)

    Lawrence, Lisa

    This document presents an integrated unit plan on snakes targeting second grade students. Objectives of the unit include developing concepts of living things, understanding the contribution and importance of snakes to the environment, and making connections between different disciplines. The unit integrates the topic of snakes into the areas of…

  4. Inlet Geomorphology Evolution Work Unit

    Science.gov (United States)

    2015-10-30

    Coastal Inlets Research Program Inlet Geomorphology Evolution Work Unit The Inlet Geomorphology Evolution work unit of the CIRP develops methods...morphologic response. Presently, the primary tool of the Inlet Geomorphology Evolution work unit is the Sediment Mobility Tool (SMT), which allows the user

  5. Synthesis and evaluation structure/extracting and complexing properties of new bi-topic ligands for group actinides extraction

    International Nuclear Information System (INIS)

    Bisson, J.

    2011-01-01

    The aim of this project is to design and study new extractants for spent nuclear fuel reprocessing. To decrease the long-term radiotoxicity of the waste, the GANEX process is an option to homogeneously recycle actinides. All actinides (U, Np, Pu, Am, Cm) would be extracted together from a highly acidic media and separated from fission products (especially from lanthanides). In this context, fourteen new bi-topic ligands constituted of a nitrogen poly-aromatic unit from the dipyridyl-phenanthroline and dipyridyl-1,3,5-triazine families and functionalized by amid groups were synthesized. Extraction studies performed with some of these ligands confirmed their interest to selectively separate actinides at different oxidation states from an aqueous solution 3M HNO 3 . To determine the influence of ligands structure on cation complexation, a study in a homogenous media (MeOH/H 2 O) has been carried out. Electro-spray ionization mass spectrometry have been used to characterize the complexes stoichiometries formed with several cations (Eu 3+ , Nd 3+ , Am 3+ , Pu 4+ and NpO 2 + ). Stability constants, evaluated by UV-Visible spectrophotometry, confirm the selectivity of these ligands toward actinides. Lanthanides and actinides complexes have also been characterized in the solid state by infra-red spectroscopy and X-Ray diffraction. Associated to nuclear magnetic resonance experiments and DFT calculations (Density Functional Theory), a better knowledge of their coordination mode was achieved. (author) [fr

  6. Determination of Terpenoid Content in Pine by Organic Solvent Extraction and Fast-GC Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Harman-Ware, Anne E., E-mail: anne.ware@nrel.gov; Sykes, Robert [National Bioenergy Center, National Renewable Energy Laboratory, Golden, CO (United States); Peter, Gary F. [School of Forest Resources and Conservation, University of Florida, Gainesville, FL (United States); Davis, Mark [National Bioenergy Center, National Renewable Energy Laboratory, Golden, CO (United States)

    2016-01-25

    Terpenoids, naturally occurring compounds derived from isoprene units present in pine oleoresin, are a valuable source of chemicals used in solvents, fragrances, flavors, and have shown potential use as a biofuel. This paper describes a method to extract and analyze the terpenoids present in loblolly pine saplings and pine lighter wood. Various extraction solvents were tested over different times and temperatures. Samples were analyzed by pyrolysis-molecular beam mass spectrometry before and after extractions to monitor the extraction efficiency. The pyrolysis studies indicated that the optimal extraction method used a 1:1 hexane/acetone solvent system at 22°C for 1 h. Extracts from the hexane/acetone experiments were analyzed using a low thermal mass modular accelerated column heater for fast-GC/FID analysis. The most abundant terpenoids from the pine samples were quantified, using standard curves, and included the monoterpenes, α- and β-pinene, camphene, and δ-carene. Sesquiterpenes analyzed included caryophyllene, humulene, and α-bisabolene. Diterpenoid resin acids were quantified in derivatized extractions, including pimaric, isopimaric, levopimaric, palustric, dehydroabietic, abietic, and neoabietic acids.

  7. Technique of calculating specific capital investments in the fuel extracting sectors of industry

    Energy Technology Data Exchange (ETDEWEB)

    Bugrov, V.A.; Filey, I.A.

    1980-01-01

    An analysis is made of the existing methods of calculating specific capital investments in the fuel extracting sectors of industry. Their shortcomings are shown. It is suggested that specific capital investments for extraction of coal and gas be defined as the ratio of capital investments to the conditional increase in extraction. Coal extraction should take int consideration all the capital investments associated with the input of new facilities, and the maintenance of the attained level of extraction and reconstruction of the enterprise, as well as all the newly introduced facilities both at the new and at the active enterprises associated with an increase in coal extraction and with maintenance of the facilities. The suggested technique completely corresponds to the ''Standard Technique for Developing a Technical-Industrial-Financial Plan,'' which stipulates determination of specific capital investments per unit of introduced facilities with only the difference that it takes into consideration the specific features of the fuel extracting sectors of industry.

  8. Enzymatic extraction of star gooseberry (Phyllanthus acidus) juice with high antioxidant level

    Science.gov (United States)

    Loan, Do Thi Thanh; Tra, Tran Thi Thu; Nguyet, Ton Nu Minh; Man, Le Van Viet

    2017-09-01

    Ascorbic acid and phenolic compounds are main antioxidants in star gooseberry (Phyllanthus acidus) fruit. In this study, Pectinex Ultra SP-L preparation with pectinase activity was used in the extraction of star gooseberry juice. The effects of pectinase concentration and biocatalytic time on the content of ascorbic acid, phenolic compounds and antioxidant activity of the fruit juice were firstly investigated. Response surface methodology was then used to optimize the conditions of enzymatic extraction for maximizing the antioxidant activity of the star gooseberry juice. The optimal pectinase concentration and biocatalytic time were 19 polygalacturonase units per 100g pulp dry weight and 67 min, respectively under which the maximal antioxidant activity achieved 5595±6 µmol Trolox equivalent per 100g juice dry weight. On the basis of kinetic model of second-order extraction, the extraction rate constant of ascorbic acid and phenolic compounds in the enzymatic extraction increased approximately 21% and 157%, respectively in comparison with that in the conventional extraction. Application of pectinase preparation to the fruit juice extraction was therefore potential for improvement in antioxidant level of the product.

  9. Determination of Terpenoid Content in Pine by Organic Solvent Extraction and Fast-GC Analysis

    International Nuclear Information System (INIS)

    Harman-Ware, Anne E.; Sykes, Robert; Peter, Gary F.; Davis, Mark

    2016-01-01

    Terpenoids, naturally occurring compounds derived from isoprene units present in pine oleoresin, are a valuable source of chemicals used in solvents, fragrances, flavors, and have shown potential use as a biofuel. This paper describes a method to extract and analyze the terpenoids present in loblolly pine saplings and pine lighter wood. Various extraction solvents were tested over different times and temperatures. Samples were analyzed by pyrolysis-molecular beam mass spectrometry before and after extractions to monitor the extraction efficiency. The pyrolysis studies indicated that the optimal extraction method used a 1:1 hexane/acetone solvent system at 22°C for 1 h. Extracts from the hexane/acetone experiments were analyzed using a low thermal mass modular accelerated column heater for fast-GC/FID analysis. The most abundant terpenoids from the pine samples were quantified, using standard curves, and included the monoterpenes, α- and β-pinene, camphene, and δ-carene. Sesquiterpenes analyzed included caryophyllene, humulene, and α-bisabolene. Diterpenoid resin acids were quantified in derivatized extractions, including pimaric, isopimaric, levopimaric, palustric, dehydroabietic, abietic, and neoabietic acids.

  10. Antibacterial activity of ethanolic extract of Myrtus communis. L leaves against salivary Mutans streptococci

    International Nuclear Information System (INIS)

    AlAnbori, Dalia K.A; AlNimer, Marwan S.M; AlWeheb, Athraa M

    2008-01-01

    The aim of this study was to evaluate the efficacy of ethanolic extract of Myrtus communis (myrtle) leaves in the selective reduction of Mutans streptococci count in saliva compared to chlorhexidine through in vitro and in vivo experiments. Ethanolic extract (2%) was prepared and screened by UV-visible spectrophotometer to detect peaks of active compounds. The minimum inhibitory concentrations (MICs) of myrtle extract as well as chlorhexidine (0.12%) were determined against Mutans streptococci isolated from human saliva and identified bacteriologically in vivo experiments, the effect of single mouth rinse of myrtle extract or chlorhexidine was investigated against the number of colony forming unit (CFU) of Mutans streptococci for two hours after rinse. The results showed the presence of one large peak at λ266.5 nm and a small one at λ672 of the extract in UV-visible spectra suggesting the presence of flavanoid. The MIC of myrtle was 106.6 μg/mL compared with 3.3 μg/mL of chlorhexidine. Single mouth rinse of myrtle extract significantly reduced the number of CFU of salivary Mutans streptococci but its effect was significantly less than that of chlorhexidine. It was concluded that the antibacterial effect of myrtle on Mutans streptococci was due to its flavanoid content. Therefore, ethanolic extract of myrtle could be a potential remedy for the prevention of colonization by Mutans streptococci thereby preventing or retarding development of dental caries. (author)

  11. Recent solvent extraction experience at Savannah River

    International Nuclear Information System (INIS)

    Gray, L.W.; Burney, G.A.; Gray, J.H.; Hodges, M.E.; Holt, D.L.; Macafee, I.M.; Reif, D.J.; Shook, H.E.

    1986-01-01

    Tributyl phosphate-based solvent extraction processes have been used at Savannah River for more than 30 years to separate and purify thorium, uranium, neptunium, plutonium, americium, and curium isotopes. This report summarizes the advancement of solvent extraction technology at Savannah River during the 1980's. Topics that are discussed include equipment improvements, solvent treatment, waste reduction, and an improved understanding of the various chemistries in the process streams entering, within, and leaving the solvent extraction processes

  12. Extraction of scandium by aromatic carboxylic acids

    International Nuclear Information System (INIS)

    Kamenev, V.F.; Fadeeva, V.I.

    1977-01-01

    Extraction of complex compounds af scandium with salicylic, phenyl- and diphenylacetic acids with chloroform solutions of tetraethyldiamideheptylphosphate as a donor-active additive in relation to the pH and reagent concentration has been studied. Extraction of salicylates of some elements (Ta, Nb, Zr, Hf, Mo) by solutions of tetraethyldiamideheptylphosphate in chloroform has been investigated, and the possibility of their extraction separation from scandium is shown

  13. Resource Extraction in a Political Economy Framework

    OpenAIRE

    Ryszka, Karolina

    2013-01-01

    We analyze resource extraction in a political economy setting by introducing a political leader who optimizes both his own and the society's welfare function. We find that accounting for the private utility of a political elite, its higher discount rate and a different time horizon generally speeds up extraction. The higher than optimal resource extraction is not only relevant in welfare terms, but also regarding possible consequences with respect to climate change. The effect of higher extra...

  14. Extraction chromatography of lanthanides, ch. 8

    International Nuclear Information System (INIS)

    Siekierski, S.; Fidelis, I.

    1975-01-01

    The extraction of lanthanides by chelate formation with acidic organophosphorous extractants, by solvation of salts, and in the form of ion pairs is reviewed. The double-double effect and its significance for the lanthanide as well as the actinide separation is discussed. A short survey of the existing data on the enthalpies of lanthanide extraction and on the influence of temperature on their separation factor is given. The resolution ability of columns used for the separation of lanthanides is briefly surveyed

  15. Supercritical solvent extraction of oil sand bitumen

    Science.gov (United States)

    Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

    2017-08-01

    The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

  16. Investigations on bark extracts of Picea abies

    Energy Technology Data Exchange (ETDEWEB)

    Weissmann, G

    1981-01-01

    Successive extraction of the bark with solvents of increasing polarity yielded about 60% of soluble material. The alcohol and water extracts contained principally simple polyphenols and their glycosides, tannins, mono-and disaccharides, soluble hemicelluloses and pectins. Hot water extracts are suitable for production of adhesives by reaction with formaldehyde, but their polyphenol content is only 50%. The polyphenols and their glycosides, and glucosides of hydroxystilbenes, were investigated in detail.

  17. Combined transuranic-strontium extraction process

    Science.gov (United States)

    Horwitz, E. Philip; Dietz, Mark L.

    1992-01-01

    The transuranic (TRU) elements neptunium, plutonium and americium can be separated together with strontium from nitric acid waste solutions in a single process. An extractant solution of a crown ether and an alkyl(phenyl)-N,N-dialkylcarbanylmethylphosphine oxide in an appropriate diluent will extract the TRU's together with strontium, uranium and technetium. The TRU's and the strontium can then be selectively stripped from the extractant for disposal.

  18. Biosynthesis of silver nanoparticles using Stevia extracts

    International Nuclear Information System (INIS)

    Laguta, I.V.; Fesenko, T.V.; Stavinskaya, O.N.; Shpak, L.M.; Dzyuba, O.I.

    2015-01-01

    Silver nanoparticles are synthesized using Stevia rebaudiana extracts. It is shown that the rate of nanoparticles formation is affected by plant cultivation conditions. It is found that, in the presence of the extract from callus, the formation of nanoparticles occurs faster than in the presence of extracts from plants grown under conditions of ex situ and in vitro. The synthesized silver nanoparticles were studied by UV and IR spectroscopies

  19. Binary Solvent Extraction System and Extraction Time Effects on Phenolic Antioxidants from Kenaf Seeds (Hibiscus cannabinus L.) Extracted by a Pulsed Ultrasonic-Assisted Extraction

    OpenAIRE

    Yu Hua Wong; Hwee Wen Lau; Chin Ping Tan; Kamariah Long; Kar Lin Nyam

    2014-01-01

    The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β -carotene bleaching inhibition assay, and ferric reducing antioxi...

  20. Extraction and Characterization of Cottonseed (Gossypium) Oil

    OpenAIRE

    Efomah Andrew Ndudi; Orhevba Bosede Adelola

    2012-01-01

    This study investigated the extraction and characterization of cottonseed oil using solvent extraction method. Normal hexane was used as solvent in the extraction process. The AOAC method of Analysis was employed in the determination of the chemical, physical and proximate compositions of the oil. The chemical properties of the oil determined include the saponification value, free fatty acid, iodine value, peroxide value and acid value. The physical properties of the oil determined are viscos...