WorldWideScience

Sample records for exposed pulps generate

  1. Biogas generation apple pulp.

    Science.gov (United States)

    Llaneza Coalla, H; Blanco Fernández, J M; Morís Morán, M A; López Bobo, M R

    2009-09-01

    In view of the pressing problem that appears in our region (Asturias, north of Spain) with the residues from the cider production, it was decided to test this kind of material as a co-substrate joint with slaughterhouse waste in a laboratory unit. The anaerobic digestion of apple pulp was investigated for biogas production. This paper presents the results where apple pulp was co-digested with slaughterhouse waste (pig intestine and bovine stomach content) in a biogas laboratory unit (10 l CSTR reactor). The production of biogas has reached very satisfactory values during the whole test (0.8m(3)kg(-1)OTS), verifying that the process is kept in stable conditions of pH (near 8.0), and the volatile fatty acids was always underneath 3000 mg/l, when the pulp amount was lower than 100g in mesophilic conditions. The fat concentration into the digester remained always below the value that causes inhibition of the methanogenic bacteria, 500 mg/l. Finally, methane concentration (77-80%) and H(2)S concentration (400 ppm) in the biogas, they were similar to those obtained when the test was run out in the absence of apple pulp. The process efficiency with respect to COD removal was high, near 80% of the total COD. Finally, inhibitory effects of methanogenic bacteria were observed when pulp concentration was around 10% in the input material.

  2. Design of a Turbulence Generator of Medium Consistency Pulp Pumps

    Directory of Open Access Journals (Sweden)

    Hong Li

    2012-01-01

    Full Text Available The turbulence generator is a key component of medium consistency centrifugal pulp pumps, with functions to fluidize the medium consistency pulp and to separate gas from the liquid. Structure sizes of the generator affect the hydraulic performance. The radius and the blade laying angle are two important structural sizes of a turbulence generator. Starting with the research on the flow inside and shearing characteristics of the MC pulp, a simple mathematical model at the flow section of the shearing chamber is built, and the formula and procedure to calculate the radius of the turbulence generator are established. The blade laying angle is referenced from the turbine agitator which has the similar shape with the turbulence generator, and the CFD simulation is applied to study the different flow fields with different blade laying angles. Then the recommended blade laying angle of the turbulence generator is formed to be between 60° and 75°.

  3. Gene expression fingerprints of largemouth bass (Micropterus salmoides) exposed to pulp and paper mill effluents.

    Science.gov (United States)

    Denslow, Nancy D; Kocerha, Jannet; Sepúlveda, Maria S; Gross, Timothy; Holm, Stewart E

    2004-08-18

    Effluents from pulp and paper mills that historically have used elemental chlorine in the bleaching process have been implicated in inhibiting reproduction in fish. Compounds with estrogenic and androgenic binding affinities have been found in these effluents, suggesting that the impairment of reproduction is through an endocrine-related mode of action. To date, a great deal of attention has been paid to phytoestrogens and resin acids that are present in mill process streams as a result of pulping trees. Estrogen and estrogen mimics interact directly with the estrogen receptor and have near immediate effects on gene transcription by turning on the expression of a unique set of genes. Using differential display (DD) RT-PCR, we examined changes in gene expression induced by exposure to paper mill effluents. Largemouth bass were exposed to 0, 10, 20, 40, and 80% paper mill effluent concentrations in large flow-through tanks for varied periods of time including 7, 28 or 56 days. Plasma hormone levels in males and females and plasma vitellogenin (Vtg) in females decreased with dose and time. Measurements of changes in gene expression using DD RT-PCR suggest that the gene expression patterns of male fish do not change much with exposure, except for the induction of a few genes including CYP 1A, a protein that is induced through the action of the Ah receptor in response to dioxin and similar polyaromatic hydrocarbons. However, in the case of females, exposure to these effluents resulted in an up-regulation of CYP 1A that was accompanied by a generalized down-regulation of genes normally expressed during the reproductive season. These antiestrogenic changes are in agreement with previous studies in bass exposed to these effluents, and could result in decreased reproductive success in affected populations.

  4. Risk factors for respiratory work disability in a cohort of pulp mill workers exposed to irritant gases

    Directory of Open Access Journals (Sweden)

    Torén Kjell

    2011-09-01

    Full Text Available Abstract Background The association between chronic respiratory diseases and work disability has been demonstrated a number of times over the past 20 years, but still little is known about work disability in occupational cohorts of workers exposed to respiratory irritants. This study investigated job or task changes due to respiratory problems as an indicator of work disability in pulp mill workers occupationally exposed to irritants. Methods Data about respiratory symptoms and disease diagnoses, socio-demographic variables, occupational exposures, gassing episodes, and reported work changes due to respiratory problems were collected using a questionnaire answered by 3226 pulp mill workers. Information about work history and departments was obtained from personnel files. Incidence and hazard ratios for respiratory work disability were calculated with 95% confidence intervals (CI. Results The incidence of respiratory work disability among these pulp mill workers was 1.6/1000 person-years. The hazard ratios for respiratory work disability were increased for workers reporting gassings (HR 5.3, 95% CI 2.7-10.5 and for those reporting physician-diagnosed asthma, chronic bronchitis, and chronic rhinitis, when analyzed in the same model. Conclusions This cohort study of pulp mill workers found that irritant peak exposure during gassing episodes was a strong predictor of changing work due to respiratory problems, even after adjustment for asthma, chronic bronchitis, and chronic rhinitis.

  5. Recovery of ovary size, follicle cell apoptosis, and HSP70 expression in fish exposed to bleached pulp mill effluent

    Energy Technology Data Exchange (ETDEWEB)

    Janz, D. M.; Weber, L. P. [Oklahoma State Univ., Stillwater, OK (United States); McMaster, M. E.; Munkittrrick, K. R. [Environment Canada, Burlington, ON (Canada); Van Der Kraak, G. [Guelph Univ., Dept. of Zoology, ON (Canada)

    2001-03-01

    Apoptosis of granulosa cells that provide hormonal support for the oocyte is the normal mechanism by which atresia ( reduced ovarian size, decreased fecundity, delayed sexual maturation, alterations in plasma sex steroid levels, etc) occurs in mammals, birds and possibly fish. The objective of this study is to determine ovarian cell apoptosis, gonadosomatic index (GSI) and heat shock protein (HSP70) expression during the growth stage of ovarian development in white sucker fish in order to compare samples of fish collected upstream and downstream of a bleached kraft pulp mill in Ontario. Fish for the study were collected in two different years, before and after the pulp mill undertook a number of improvements to eliminate the release of process chemicals. Results showed a 3.4-fold increase in ovarian cell apoptosis in growing white sucker collected four km downstream of the bleached kraft pulp mill in 1996 (before the improvements) compared to fish collected from upstream sources. The elevated ovarian cell apoptosis was associated with significant reduction in gonadosomatic index in fish collected downstream. There were no differences in ovarian cell apoptosis or gonadosomatic index between fish collected upstream and four km downstream of the mill in September 1998 (after the improvements.) Based on the results, it may be concluded that chronic stimulation of ovarian cell apoptosis by certain components of bleached kraft pulp mill effluents represents an important cellular mechanism for reducing the size of ovaries and other related reproductive responses in female fish exposed to these effluents. Although the specific effluent components are not known, the improvements undertaken between 1996 and 1998 resulted in significant enough recovery of these responses to justify the belief in a cause-effect relationship. 32 refs., 1 tab., 2 figs.

  6. Generation of Hydrogen, Lignin and Sodium Hydroxide from Pulping Black Liquor by Electrolysis

    Directory of Open Access Journals (Sweden)

    Guangzai Nong

    2015-12-01

    Full Text Available Black liquor is generated in Kraft pulping of wood or non-wood raw material in pulp mills, and regarded as a renewable resource. The objective of this paper was to develop an effective means to remove the water pollutants by recovery of both lignin and sodium hydroxide from black liquor, based on electrolysis. The treatment of a 1000 mL of black liquor (122 g/L solid contents consumed 345.6 kJ of electric energy, and led to the generation of 30.7 g of sodium hydroxide, 0.82 g of hydrogen gas and 52.1 g of biomass solids. Therefore, the recovery ratios of elemental sodium and biomass solids are 80.4% and 76%, respectively. Treating black liquor by electrolysis is an environmentally friendly technology that can, in particular, be an alternative process in addressing the environmental issues of pulping waste liquor to the small-scale mills without black liquor recovery.

  7. Use of coffee (Coffea arabica pulp for the production of briquettes and pellets for heat generation

    Directory of Open Access Journals (Sweden)

    Robert Cubero-Abarca

    2014-10-01

    Full Text Available Coffee bean (Coffea arabica processing generates high amount of residues that are sources of environmental pollution. Therefore, an appropriate solution is needed. The objective of this study was to determine the potential of coffee pulp to produce briquettes and pellets. The study included pulp drying (using air, solar and hot air methods; the production of briquettes and pellets; the evaluation of their energy, physical and mechanical properties; and the evaluation of pellet quality using X-ray densitometry. The results showed that the pulp presented an initial moisture content of 90%, resulting in drying times of 699, 308 and 55 hours for air, solar and hot air drying, respectively, and the calorific values of the pellets and briquettes were 12,501 kJ kg-1 and 11,591 kJ kg-1, respectively. The ash content was 8.68% for the briquettes and 6.74% for the pellets. The density of the briquettes was 1,110 kg m-3, compared with 1,300 kg m-3 for the pellets. The apparent densities were 1,000 kg m-3 and 600 kg m-3 for the briquettes and pellets, respectively, and the water absorptions by the briquettes were 7.90% and 8.10% by the pellets. The maximum horizontal compression effort was 26.86 kg cm-2, measured in the pellets, compared with 4.52 kg cm-2 in the briquettes. The maximum horizontal load was 93.24 kg, measured in the briquettes, compared with 33.50 kg in the pellets. The value of the pellet durability test was 75.54%. X-ray densitometry showed that the pellet was uniform and a few cracks were observed on the pellet surface.

  8. Functionalized scaffolds to control dental pulp stem cell fate

    Science.gov (United States)

    Piva, Evandro; Silva, Adriana F.; Nör, Jacques E.

    2014-01-01

    Emerging understanding about interactions between stem cells, scaffolds and morphogenic factors has accelerated translational research in the field of dental pulp tissue engineering. Dental pulp stem cells constitute a sub-population of cells endowed with self-renewal and multipotency. Dental pulp stem cells seeded in biodegradable scaffolds and exposed to dentin-derived morphogenic signals give rise to a pulp-like tissue capable of generating new dentin. Notably, dentin-derived proteins are sufficient to induce dental pulp stem cell differentiation into odontoblasts. Ongoing work is focused on developing ways of mobilizing dentin-derived proteins and disinfecting the root canal of necrotic teeth without compromising the morphogenic potential of these signaling molecules. On the other hand, dentin by itself does not appear to be capable of inducing endothelial differentiation of dental pulp stem cells, despite the well known presence of angiogenic factors in dentin. This is particularly relevant in the context of dental pulp tissue engineering in full root canals, where access to blood supply is limited to the apical foramina. To address this challenge, scientists are looking at ways to use the scaffold as a controlled release device for angiogenic factors. The aim of this manuscript is to present and discuss current strategies to functionalize injectable scaffolds and customize them for dental pulp tissue engineering. The long-term goal of this work is to develop stem cell-based therapies that enable the engineering of functional dental pulps capable of generating new tubular dentin in humans. PMID:24698691

  9. Breeding Strategy To Generate Robust Yeast Starter Cultures for Cocoa Pulp Fermentations

    Science.gov (United States)

    Meersman, Esther; Steensels, Jan; Paulus, Tinneke; Struyf, Nore; Saels, Veerle; Mathawan, Melissa; Koffi, Jean; Vrancken, Gino

    2015-01-01

    Cocoa pulp fermentation is a spontaneous process during which the natural microbiota present at cocoa farms is allowed to ferment the pulp surrounding cocoa beans. Because such spontaneous fermentations are inconsistent and contribute to product variability, there is growing interest in a microbial starter culture that could be used to inoculate cocoa pulp fermentations. Previous studies have revealed that many different fungi are recovered from different batches of spontaneous cocoa pulp fermentations, whereas the variation in the prokaryotic microbiome is much more limited. In this study, therefore, we aimed to develop a suitable yeast starter culture that is able to outcompete wild contaminants and consistently produce high-quality chocolate. Starting from specifically selected Saccharomyces cerevisiae strains, we developed robust hybrids with characteristics that allow them to efficiently ferment cocoa pulp, including improved temperature tolerance and fermentation capacity. We conducted several laboratory and field trials to show that these new hybrids often outperform their parental strains and are able to dominate spontaneous pilot scale fermentations, which results in much more consistent microbial profiles. Moreover, analysis of the resulting chocolate showed that some of the cocoa batches that were fermented with specific starter cultures yielded superior chocolate. Taken together, these results describe the development of robust yeast starter cultures for cocoa pulp fermentations that can contribute to improving the consistency and quality of commercial chocolate production. PMID:26150457

  10. Breeding Strategy To Generate Robust Yeast Starter Cultures for Cocoa Pulp Fermentations.

    Science.gov (United States)

    Meersman, Esther; Steensels, Jan; Paulus, Tinneke; Struyf, Nore; Saels, Veerle; Mathawan, Melissa; Koffi, Jean; Vrancken, Gino; Verstrepen, Kevin J

    2015-09-01

    Cocoa pulp fermentation is a spontaneous process during which the natural microbiota present at cocoa farms is allowed to ferment the pulp surrounding cocoa beans. Because such spontaneous fermentations are inconsistent and contribute to product variability, there is growing interest in a microbial starter culture that could be used to inoculate cocoa pulp fermentations. Previous studies have revealed that many different fungi are recovered from different batches of spontaneous cocoa pulp fermentations, whereas the variation in the prokaryotic microbiome is much more limited. In this study, therefore, we aimed to develop a suitable yeast starter culture that is able to outcompete wild contaminants and consistently produce high-quality chocolate. Starting from specifically selected Saccharomyces cerevisiae strains, we developed robust hybrids with characteristics that allow them to efficiently ferment cocoa pulp, including improved temperature tolerance and fermentation capacity. We conducted several laboratory and field trials to show that these new hybrids often outperform their parental strains and are able to dominate spontaneous pilot scale fermentations, which results in much more consistent microbial profiles. Moreover, analysis of the resulting chocolate showed that some of the cocoa batches that were fermented with specific starter cultures yielded superior chocolate. Taken together, these results describe the development of robust yeast starter cultures for cocoa pulp fermentations that can contribute to improving the consistency and quality of commercial chocolate production. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  11. Estrogenicity and intersex in juvenile rainbow trout (Oncorhynchus mykiss) exposed to Pine/Eucalyptus pulp and paper production effluent in Chile

    International Nuclear Information System (INIS)

    Chiang, Gustavo; Barra, Ricardo; Díaz-Jaramillo, Mauricio; Rivas, Meyling; Bahamonde, Paulina; Munkittrick, Kelly R.

    2015-01-01

    Highlights: • Juvenile rainbow were exposed to Pine and Eucalyptus PPME along with an in situ bioassay downstream of the combined discharge. • Fish exposed to PPME showed induced levels of plasma vitellogenin and female gonad maturation. • Male fish showed intersex characteristics in laboratory and in situ assays. • Tertiary treated PPME from Eucalyptus production have stronger estrogenic effects on juvenile fish. - Abstract: Pulp and paper mill effluents (PPMEs) have been shown to increase gonad size, cause early maturation, and disrupt hormone functions in native and non-native Chilean fish. In this study, we assessed reproductive (plasma vitellogenin; VTG, gonad development) and metabolic (ethoxyresorufin-O-deethylase activity; EROD) end points, relative liver size (LSI) and condition factor (K) of juvenile female and male rainbow trout exposed to effluents. Unlike previous studies, which have focus either on the specific effects of effluent on fish in laboratory exposures or biotic population statuses downstream of discharge sites, we simultaneously assessed the impacts of PPMES on trout using two approaches: (1) laboratory exposures of tertiary treated PPME produced from processing Eucalyptus globulus or Pinus radiata; and (2) in situ bioassay downstream of the combined discharge of the same pulp mill. Despite an increase in the average gonadosomatic index (GSI) in exposed fish, no statistical differences in gonad size between exposed and unexposed individuals was detected. However, both female and male fish exposed to effluents showed significantly higher concentrations of plasma VTG, so more in fish exposed to Eucalyptus-based effluent when compared to Pinus PPME. In addition, male fish showed intersex characteristics in all exposure assays (Eucaliptus and Pinus) and, despite the low concentration of effluent in the river (<1% [v/v]), similar responses were observed in the caged fish. Finally, EROD activity was induced in both in situ exposures and

  12. Estrogenicity and intersex in juvenile rainbow trout (Oncorhynchus mykiss) exposed to Pine/Eucalyptus pulp and paper production effluent in Chile

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, Gustavo, E-mail: gchiang@centromeri.cl [Canadian Rivers Institute and Department of Biology, University of New Brunswick, Saint John, NB E2L 4L5 (Canada); Barra, Ricardo [Aquatic Systems Research Unit, EULA–Chile Environmental Sciences Centre, University of Concepción, Concepcion (Chile); Díaz-Jaramillo, Mauricio [Laboratorio de Ecotoxicología y Contaminación Ambiental (ECoA), IIMyC-CONICET-UNMdP, Mar del Plata (Argentina); Rivas, Meyling [Department of Zoology, Faculty of Natural and Oceanographic Sciences, University of Concepcion, Concepcion (Chile); Bahamonde, Paulina; Munkittrick, Kelly R. [Canadian Rivers Institute and Department of Biology, University of New Brunswick, Saint John, NB E2L 4L5 (Canada)

    2015-07-15

    Highlights: • Juvenile rainbow were exposed to Pine and Eucalyptus PPME along with an in situ bioassay downstream of the combined discharge. • Fish exposed to PPME showed induced levels of plasma vitellogenin and female gonad maturation. • Male fish showed intersex characteristics in laboratory and in situ assays. • Tertiary treated PPME from Eucalyptus production have stronger estrogenic effects on juvenile fish. - Abstract: Pulp and paper mill effluents (PPMEs) have been shown to increase gonad size, cause early maturation, and disrupt hormone functions in native and non-native Chilean fish. In this study, we assessed reproductive (plasma vitellogenin; VTG, gonad development) and metabolic (ethoxyresorufin-O-deethylase activity; EROD) end points, relative liver size (LSI) and condition factor (K) of juvenile female and male rainbow trout exposed to effluents. Unlike previous studies, which have focus either on the specific effects of effluent on fish in laboratory exposures or biotic population statuses downstream of discharge sites, we simultaneously assessed the impacts of PPMES on trout using two approaches: (1) laboratory exposures of tertiary treated PPME produced from processing Eucalyptus globulus or Pinus radiata; and (2) in situ bioassay downstream of the combined discharge of the same pulp mill. Despite an increase in the average gonadosomatic index (GSI) in exposed fish, no statistical differences in gonad size between exposed and unexposed individuals was detected. However, both female and male fish exposed to effluents showed significantly higher concentrations of plasma VTG, so more in fish exposed to Eucalyptus-based effluent when compared to Pinus PPME. In addition, male fish showed intersex characteristics in all exposure assays (Eucaliptus and Pinus) and, despite the low concentration of effluent in the river (<1% [v/v]), similar responses were observed in the caged fish. Finally, EROD activity was induced in both in situ exposures and

  13. Comparison of the Amount of Temperature Rise in the Pulp Chamber of Teeth Treated With QTH, Second and Third Generation LED Light Curing Units: An In Vitro Study.

    Science.gov (United States)

    Mahant, Rajesh Harivadanbhai; Chokshi, Shraddha; Vaidya, Rupal; Patel, Pruthvi; Vora, Asima; Mahant, Priyanka

    2016-01-01

    Introduction: This in vitro study was designed to measure and compare the amount of temperature rise in the pulp chamber of the teeth exposed to different light curing units (LCU), which are being used for curing composite restorations. Methods: The study was performed in two settings; first, an in vitro and second was mimicking an in vivo situation. In the first setup of the study, three groups were formed according to the respective three light curing sources. i.e. quartz-tungsten-halogen (QTH) unit and two light-emitting diode (LED) units (second and third generations). In the in vitro setting, direct thermal emission from three light sources at 3 mm and 6 mm distances, was measured with a k-type thermocouple, and connected to a digital thermometer. For a simulation of an in vivo situation, 30 premolar teeth were used. Class I Occlusal cavity of all the teeth were prepared and they were restored with incremental curing of composite, after bonding agent application. While curing the bonding agent and composite in layers, the intrapulpal temperature rise was simultaneously measured with a k-type thermocouple. Results: The first setting of the study showed that the heat produced by irradiation with LCU was significantly less at 6 mm distance when compared to 3 mm distance. The second setting of the study showed that the rise of intrapulpal temperature was significantly less with third generation LED light cure units than with second generation LED and QTH light cure units. Conclusion: As the distance from the light source increases, less irradiation heat is produced. Third generation LED lights cause the least temperature change in the pulp chamber of single rooted teeth.

  14. Generation of biogas from coffee-pulp and cow-dung co-digestion: Infrared studies of postcombustion emissions

    International Nuclear Information System (INIS)

    Corro, Grisel; Paniagua, Laura; Pal, Umapada; Bañuelos, Fortino; Rosas, Minerva

    2013-01-01

    Graphical abstract: Batch digester with coffee pulp/cow dung produced high amounts of methane for 8 months. The FTIR gas spectroscopy analysis revealed the presence of over 70 chemical compounds in biogas generated after 4 months of coffee pulp and cow dung mixture co-digestion, several being hazardous to environment and human and animal health (e.g. isocyanic acid, bromomethane). Biogas produced was burned in a laboratory combustor. The FTIR gas spectroscopy analysis showed that combustion emissions contained: CH 4 , C 3 H 8 , CO, SO 2 , HI, and probably Br 2 which are strongly harmful to human and animal health. - Highlights: • Batch digester with coffee pulp/cow dung produced high amounts of methane for 8 months. • Biogas from coffee pulp/cow dung codigestion contained 60% methane and 20% propane. • Biogas FTIR analysis revealed the presence of isocyanic acid and bromomethane. • Biogas FTIR analysis showed also the presence of HI. • Biogas combustion emissions contained CH 4 , HI, SO 2 and probably Br 2 . - Abstract: Biogas could be produced by the co-digestion of coffee-pulp and cow-dung mixture under solar radiation. Gas chromatography and FTIR spectroscopy were used to analyze the chemical compositions of the generated biogas and its postcombustion emissions. From the first month of co-digestion at mesophylic conditions, methane content in the biogas attains 50% of the yield. This content increased up to 60% and remained almost constant for at least 8 months of further digestion. The FTIR gas spectroscopy analysis revealed the presence of over 70 chemical compounds in the biogas generated after 4 months of co-digestion along with several compounds hazardous to environment and animal health like isocyanic acid, and bromomethane. Combustion emission of the biogas contained several components like CH 4 , C 3 H 8 , CO, SO 2 , HI, and probably Br 2 which are strongly harmful to human and animal health. Results presented in this work indicate that if the

  15. Gene expression change in human dental pulp cells exposed to a low-level toxic concentration of triethylene glycol dimethacrylate: an RNA-seq analysis.

    Science.gov (United States)

    Cho, Sung-Geun; Lee, Jin-Woo; Heo, Jung Sun; Kim, Sun-Young

    2014-09-01

    Dental composite resin restoration for defective tooth may lead unpolymerized resin monomers to be leached into dental pulp tissue. The aim of this study was to investigate the early gene expression change over time of human dental pulp cells (HDPCs) treated with a low-level toxic concentration of Triethylene Glycol Dimethacrylate (TEGDMA), a common dental resin monomer, by adopting the novel high-throughput transcriptome analysis of RNA-seq. The low-level toxic concentration of TEGDMA was determined through MTT assays with serially diluted concentrations. After the HDPCs were exposed to TEGDMA for 6, 12, 24 or 48 hr, the total RNA of the samples was prepared for RNA-seq. qRT-PCR for several genes was performed for validation of RNA-seq results. In the treated group, 1280 genes were differentially expressed compared with the control group. Five patterns of time-series gene expression profiles were identified through k-means clustering analysis. Angiogenesis, cell adhesion and migration, extracellular matrix organization, response to extracellular stimulus, inflammatory response and mineralization-related process were major gene ontology terms in functional annotation clustering. HMOX1, OSGIN1, SMN2, SRXN1 AKR1C1, SPP1 and TOMM40L were highly up-regulated genes, and WRAP53 and CCL2 were highly down-regulated genes over time. qRT-PCR for several genes exhibited a high level of agreement with RNA-seq. TEGDMA induced the HDPCs to show massive and dynamic gene expression changes over time. The previously suggested toxic mechanism of TEGDMA was not only verified, but new genes whose functions have yet to be determined were also found. © 2014 Nordic Association for the Publication of BCPT (former Nordic Pharmacological Society).

  16. The potential for generating a surplus of biomass fuel in the pulp and paper industry

    Energy Technology Data Exchange (ETDEWEB)

    Wising, U.

    2001-06-01

    The conditions under which the pulp and paper industry is working are changing. New technology and new environmental objectives lead to changes: system closure (less water is used); processes are introduced and modified; new, more energy efficient processes are applied. Many of these changes affect the energy system in a mill and can also result in new potential for energy savings. Here a method is described and applied to six modern and/or future green field kraft market pulp model mills. The basic configuration for these model mills is designed according to best available technology today and consists of commercially available equipment in conventionally designed mills. These basic configurations are process integrated using Pinch Technology to ensure that the model mills are as energy efficient as possible with existing processes. Then by allowing process and system modifications, the model mills are made even more energy efficient. From the process integration study streams that could produce usable excess heat below the Pinch temperature are identified. In a pulp mill, necessary cooling is performed while producing warm and hot water. In modern mills there is usually a surplus of warm and hot water. It is herein presented that by designing the secondary heat system differently such that only necessary warm and hot water is produced, excess heat at a higher temperature than traditionally can be made available. The excess heat made available can be used for several applications; in this work it is used for evaporation. In order to use the excess heat for evaporation the evaporation plant has to be designed non-conventionally, with more than one level where heat is supplied, and a lower temperature in the surface condenser than what is typically used. A reasonable level of the extra investment cost for the novel system compared to the reference system is then calculated and a payback period is estimated. This payback period varies between approximately 3.5 and 6

  17. The use of biomass energy in the pulp and paper industry and the prospects for black liquor gasification combined cycle generation

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, L J [Department of Environmental and Energy Systems Studies, Lund University, Lund (Sweden)

    1995-12-01

    The world production of paper and paperboard products, which increased 3.3% per year since 1980, reached 243 million tonnes in 1991 and is expected to continue to grow by about 2.5% per year over the next decade. Consumption levels in 1990 ranged from 2.8 kg per capita in India to 313 kg per capita in the United States. The biggest producers of pulp are the United States, Canada and the Scandinavian countries, but much of the expansion of pulp production capacity is taking place in countries such as Brazil, Chile and Indonesia. The pulp and paper industry has always relied on biomass as a fuel source to meet process energy demands. Kraft pulping is the most common process accounting for about two thirds of world wood pulp production. Energy recovered from burning black liquor, a lignin-rich by-product, in a chemicals recovery boiler typically provides most of the on-site demand for heat and electricity in a modem kraft pulp mill. Another important fuel source is bark and wood waste generated at the mill. Aging recovery boilers in industrialized countries and increasing electricity/heat demand ratios are stimulating interest in alternative co-generation technologies. Most of the interest in new biomass and black liquor co-generation technologies focuses on those that would utilize gas turbines rather than steam turbines. Gas turbines are generally characterized by higher electricity/heat ratios than steam turbines, as well as lower unit capital costs. With the black liquor and biomass gasification technologies that are now being developed and demonstrated, the energy needs of an energy-efficient kraft pulp mill could be met and 40-50 MW of baseload power would be available for export. Using, in addition, currently unused logging residues for fuel would increase that potential. The pulp and paper industry is likely to be an important early market for advanced biomass-based cogeneration technology owing to its access to biomass fuels and the potential for co-generation

  18. The use of biomass energy in the pulp and paper industry and the prospects for black liquor gasification combined cycle generation

    International Nuclear Information System (INIS)

    Nilsson, L.J.

    1995-01-01

    The world production of paper and paperboard products, which increased 3.3% per year since 1980, reached 243 million tonnes in 1991 and is expected to continue to grow by about 2.5% per year over the next decade. Consumption levels in 1990 ranged from 2.8 kg per capita in India to 313 kg per capita in the United States. The biggest producers of pulp are the United States, Canada and the Scandinavian countries, but much of the expansion of pulp production capacity is taking place in countries such as Brazil, Chile and Indonesia. The pulp and paper industry has always relied on biomass as a fuel source to meet process energy demands. Kraft pulping is the most common process accounting for about two thirds of world wood pulp production. Energy recovered from burning black liquor, a lignin-rich by-product, in a chemicals recovery boiler typically provides most of the on-site demand for heat and electricity in a modem kraft pulp mill. Another important fuel source is bark and wood waste generated at the mill. Aging recovery boilers in industrialized countries and increasing electricity/heat demand ratios are stimulating interest in alternative co-generation technologies. Most of the interest in new biomass and black liquor co-generation technologies focuses on those that would utilize gas turbines rather than steam turbines. Gas turbines are generally characterized by higher electricity/heat ratios than steam turbines, as well as lower unit capital costs. With the black liquor and biomass gasification technologies that are now being developed and demonstrated, the energy needs of an energy-efficient kraft pulp mill could be met and 40-50 MW of baseload power would be available for export. Using, in addition, currently unused logging residues for fuel would increase that potential. The pulp and paper industry is likely to be an important early market for advanced biomass-based cogeneration technology owing to its access to biomass fuels and the potential for co-generation

  19. Kraft pulping of industrial wood waste

    Science.gov (United States)

    Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

    1998-01-01

    Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

  20. Genetic and demographic responses of mosquitofish (Gambusia holbrooki) populations exposed to mercury for multiple generations

    Energy Technology Data Exchange (ETDEWEB)

    Tatara, C.P.; Mulvey, M.; Newman, M.C.

    1999-12-01

    Genetic and demographic responses of mosquitofish were examined after multiple generations of exposure to mercury. Previous studies of acute lethal exposures of mosquitofish to either mercury or arsenic demonstrated a consistent correlation between time to death and genotype at the glucosephosphate isomerase-2 (Gpi-2) locus. A mesocosm study involving mosquitofish populations exposed to mercury for 111 d showed significant female sexual selection and fecundity selection at the Gpi-2 locus. Here the mesocosm study was extended to populations exposed to mercury for several (approx. four) generations. After 2 years, control and mercury-exposed populations met Hardy-Weinberg expectations and showed no evidence of genetic bottlenecks. The mean number of heterozygous loci did not differ significantly between the mercury-exposed and control populations. Significant differences in allele frequencies at the Gpi-2 locus were observed between the mercury-exposed and control populations. Relative to the initial and control allele frequencies, the GPI-2{sup 100} allele frequency was lower, the Gpi-2{sup 66} allele frequency increased, but the Gpi-2{sup 38} allele frequency did not change in mercury-exposed populations. No significant differences were found in standard length, weight, sex ratio, or age class ratio between the control and mercury-exposed populations. Allele frequency changes at the Gpi-2 locus suggest population-level response to chronic mercury exposure. Changes in allele frequency may be useful as indicators of population response to contaminants, provided that the population in question is well understood.

  1. The induction of dentin bridge-like structures by constructs of subcultured dental pulp-derived cells and porous HA/TCP in porcine teeth.

    Science.gov (United States)

    Ando, Yusuke; Honda, Masaki J; Ohshima, Hayato; Tonomura, Akiko; Ohara, Takayuki; Itaya, Toshimitsu; Kagami, Hideaki; Ueda, Minoru

    2009-02-01

    The purpose of this study was to investigate dentin-bridge formation in teeth following the transplantation of dental pulp-derived cells seeded on hydroxyapatite/tricalcium phosphate (HA/TCP) scaffolds. The dental pulp tissues were removed from the extracted first molar teeth of miniature pigs and single cell populations were subcultured. Second-passage cells that had alkaline phosphatase activity were combined with scaffolds. Cell-scaffold constructs were placed in contact with the exposed pulp tissue. The dimensions of the exposed pulp site were approximately 1-2.5 mm in diameter and 2-3 mm in depth from the tooth surface. After placing the constructs, the tooth was restored with composite resin. Six weeks after transplantation, hard tissue formation was observed on the pulp tissue in histology. Dentinal tubule-like structures were observed in most of the hard tissue generated, and columnar cells, which showed positive immunoreactions with dentin sialoprotein (DSP) and heat shock protein (HSP)-25, were aligned beneath the hard tissues. When only scaffolds were placed on the pulp tissues, particles of hard tissue were formed, however dentinal tubule-like structures and odontoblasts were not observed despite the formation of hard tissue. In conclusion, the implantation of dental pulp constructs into pulp exposed stimulates the formation of calcified dentin-like structures.

  2. Transcriptome comparison of human neurons generated using induced pluripotent stem cells derived from dental pulp and skin fibroblasts.

    Science.gov (United States)

    Chen, Jian; Lin, Mingyan; Foxe, John J; Pedrosa, Erika; Hrabovsky, Anastasia; Carroll, Reed; Zheng, Deyou; Lachman, Herbert M

    2013-01-01

    Induced pluripotent stem cell (iPSC) technology is providing an opportunity to study neuropsychiatric disorders through the capacity to grow patient-specific neurons in vitro. Skin fibroblasts obtained by biopsy have been the most reliable source of cells for reprogramming. However, using other somatic cells obtained by less invasive means would be ideal, especially in children with autism spectrum disorders (ASD) and other neurodevelopmental conditions. In addition to fibroblasts, iPSCs have been developed from cord blood, lymphocytes, hair keratinocytes, and dental pulp from deciduous teeth. Of these, dental pulp would be a good source for neurodevelopmental disorders in children because obtaining material is non-invasive. We investigated its suitability for disease modeling by carrying out gene expression profiling, using RNA-seq, on differentiated neurons derived from iPSCs made from dental pulp extracted from deciduous teeth (T-iPSCs) and fibroblasts (F-iPSCs). This is the first RNA-seq analysis comparing gene expression profiles in neurons derived from iPSCs made from different somatic cells. For the most part, gene expression profiles were quite similar with only 329 genes showing differential expression at a nominally significant p-value (pdisease-modeling neuropsychiatric disorder and may have some advantages over those derived from F-iPSCs.

  3. Radiation modification of cellulose pulps. Preparation of cellulose derivatives

    International Nuclear Information System (INIS)

    Iller, E.; Zimek, Z.; Stupinska, H.; Mikolajczyk, W; Starostka, P.

    2005-01-01

    One of the most common methods of cellulose pulp modification (activation) applied in the production process of cellulose derivatives is the treatment of the pulp with NaOH solutions leading to the formation of alkalicellulose. The product then undergoes a prolonged process of maturation by its storage under specific conditions. The goal of the process is lowering of the molecular weight of cellulose down to the level resulting from various technological requirements. The process is time-consuming and costly; besides, it requires usage of large-capacity technological vessels and produces considerable amounts of liquid waste. Therefore, many attempts have been made to limit or altogether eliminate the highly disadvantageous stage of cellulose treatment with lye. One of the alternatives proposed so far is the radiation treatment of the cellulose pulp. In the pulp exposed to an electron beam, the bonds between molecules of D-antihydroglucopiranoses loosen and the local crystalline lattice becomes destroyed. This facilitates the access of chemical reagents to the inner structure of the cellulose and, in consequence, eliminates the need for the prolonged maturation of alkalicellulose, thus reducing the consumption of chemicals by the whole process. Research aimed at the application of radiation treatment of cellulose pulp for the production of cellulose derivatives has been conducted by a number of scientific institutions including the Institute of Nuclear Chemistry and Technology, Institute of Biopolymers and Chemical Fibres, and Pulp and Paper Research Institute. For the investigations and assessment of the molecular, hypermolecular, morphologic properties and the chemical reactivity, cellulose pulps used for chemical processing, namely Alicell, Borregaard and Ketchikan, as well as paper pulps made from pine and birch wood were selected. The selected cellulose pulps were exposed to an electron beam with an energy of 10 MeV generated in a linear electron accelerator

  4. [Vital pulp therapy of damaged dental pulp].

    Science.gov (United States)

    Xuedong, Zhou; Dingming, Huang; Jianguo, Liu; Zhengwei, Huang; Xin, Wei; Deqin, Yang; Jin, Zhao; Liming, Chen; Lin, Zhu; Yanhong, Li; Jiyao, Li

    2017-08-01

    The development of an expert consensus on vital pulp therapy can provide practical guidance for the improvement of pulp damage care in China. Dental pulp disease is a major type of illness that adversely affects human oral health. Pulp capping and pulpotomy are currently the main methods for vital pulp therapy. Along with the development of minimal invasion cosmetic dentistry, using different treatment technologies and materials reasonably, preserving healthy tooth tissue, and extending tooth save time have become urgent problems that call for immediate solution in dental clinics. This paper summarizes the experiences and knowledge of endodontic experts. We develop a clinical path of vital pulp therapy for clinical work by utilizing the nature, approach, and degree of pulp damage as references, defense and self-repairing ability of pulp as guidance, and modern technologies of diagnosis and treatment as means.

  5. Adaptive response of Chironomus riparius populations exposed to uranium contaminated sediments during consecutive generations

    International Nuclear Information System (INIS)

    Dias, V.

    2010-01-01

    The intensity of selection on populations caused by polluted environment often exceeds which is caused by an unpolluted environment. Therefore, micro evolution can occur in response to this anthropic-directional force over a short period. In this context, this thesis focused on studying phenotypic changes in Chironomus riparius populations exposed during several consecutive generations to uranium-contaminated sediments. In laboratory-controlled conditions experiments were conducted with same origin populations exposed to a range of uranium concentration inducing toxic effects. Over eight-generations of exposure, life-history traits measures revealed micro evolution in exposed populations, including increase of adult reproductive success. Other experiments (acute toxicity test, common garden experiment) performed in parallel enabled to link these micro evolution with a tolerance induction, as a consequence of genetic adaptation. Nonetheless this adaptation also induced cost in terms of fitness and genetic diversity for pre-exposed populations. These results lead to the hypothesis of a selection by uranium that acted sequentially on populations. They also underline the need to better-understand the adaptive mechanisms to better assess the ecological consequences of chronic exposure of populations to a pollutant. (author)

  6. Modeling, simulation, and analysis of a reactor system for the generation of white liquor of a pulp and paper industry

    Directory of Open Access Journals (Sweden)

    Ricardo Andreola

    2011-02-01

    Full Text Available An industrial system for the production of white liquor of a pulp and paper industry, Klabin Paraná Papéis, formed by ten reactors was modeled, simulated, and analyzed. The developed model considered possible water losses by the evaporation and reaction, in addition to variations in the volumetric flow of lime mud across the reactors due to the composition variations. The model predictions agreed well with the process measurements at the plant and the results showed that the slaking reaction was nearly complete at the third causticizing reactor, while causticizing ends by the seventh reactor. Water loss due to slaking reaction and evaporation occurred more pronouncedly in the slaker reactor than in the final causticizing reactors; nevertheless, the lime mud flow remained nearly constant across the reactors.

  7. Reproductive gene expression in a coral reef fish exposed to increasing temperature across generations

    KAUST Repository

    Veilleux, Heather D; Donelson, Jennifer M; Munday, Philip L

    2017-01-01

    Reproduction in marine fish is generally tightly linked with water temperature. Consequently, when adults are exposed to projected future ocean temperatures, reproductive output of many species declines precipitously. Recent research has shown that in the common reef fish, Acanthochromis polyacanthus, step-wise exposure to higher temperatures over two generations (parents: +1.5°C, offspring: +3.0°C) can improve reproductive output in the F2 generation compared to F2 fish that have experienced the same high temperatures over two generations (F1 parents: +3.0°C, F2 offspring: +3.0°C). To investigate how a step-wise increase in temperature between generations improved reproductive capacity, we tested the expression of well-known teleost reproductive genes in the brain and gonads of F2 fish using quantitative reverse transcription PCR and compared it among control (+0.0°C for two generations), developmental (+3.0°C in second generation only), step (+1.5°C in first generation and +3.0°C in second generation), and transgenerational (+3.0°C for two generations) treatments. We found that levels of gonadotropin receptor gene expression (Fshr and Lhcgr) in the testes were reduced in developmental and transgenerational temperature treatments, but were similar to control levels in the step treatment. This suggests Fshr and Lhcgr may be involved in regulating male reproductive capacity in A. polyacanthus. In addition, lower Fshb expression in the brain of females in all temperature treatments compared to control, suggests that Fshb expression, which is involved in vitellogenesis, is sensitive to high temperatures. Our results help elucidate key genes that facilitate successful reproduction in reef fishes when they experience a gradual increase in temperature across generations consistent with the trajectory of climate change.

  8. Reproductive gene expression in a coral reef fish exposed to increasing temperature across generations.

    Science.gov (United States)

    Veilleux, Heather D; Donelson, Jennifer M; Munday, Philip L

    2018-01-01

    Reproduction in marine fish is generally tightly linked with water temperature. Consequently, when adults are exposed to projected future ocean temperatures, reproductive output of many species declines precipitously. Recent research has shown that in the common reef fish, Acanthochromis polyacanthus , step-wise exposure to higher temperatures over two generations (parents: +1.5°C, offspring: +3.0°C) can improve reproductive output in the F2 generation compared to F2 fish that have experienced the same high temperatures over two generations (F1 parents: +3.0°C, F2 offspring: +3.0°C). To investigate how a step-wise increase in temperature between generations improved reproductive capacity, we tested the expression of well-known teleost reproductive genes in the brain and gonads of F2 fish using quantitative reverse transcription PCR and compared it among control (+0.0°C for two generations), developmental (+3.0°C in second generation only), step (+1.5°C in first generation and +3.0°C in second generation), and transgenerational (+3.0°C for two generations) treatments. We found that levels of gonadotropin receptor gene expression ( Fshr and Lhcgr ) in the testes were reduced in developmental and transgenerational temperature treatments, but were similar to control levels in the step treatment. This suggests Fshr and Lhcgr may be involved in regulating male reproductive capacity in A. polyacanthus . In addition, lower Fshb expression in the brain of females in all temperature treatments compared to control, suggests that Fshb expression, which is involved in vitellogenesis, is sensitive to high temperatures. Our results help elucidate key genes that facilitate successful reproduction in reef fishes when they experience a gradual increase in temperature across generations consistent with the trajectory of climate change.

  9. Reproductive gene expression in a coral reef fish exposed to increasing temperature across generations

    KAUST Repository

    Veilleux, Heather D

    2017-12-07

    Reproduction in marine fish is generally tightly linked with water temperature. Consequently, when adults are exposed to projected future ocean temperatures, reproductive output of many species declines precipitously. Recent research has shown that in the common reef fish, Acanthochromis polyacanthus, step-wise exposure to higher temperatures over two generations (parents: +1.5°C, offspring: +3.0°C) can improve reproductive output in the F2 generation compared to F2 fish that have experienced the same high temperatures over two generations (F1 parents: +3.0°C, F2 offspring: +3.0°C). To investigate how a step-wise increase in temperature between generations improved reproductive capacity, we tested the expression of well-known teleost reproductive genes in the brain and gonads of F2 fish using quantitative reverse transcription PCR and compared it among control (+0.0°C for two generations), developmental (+3.0°C in second generation only), step (+1.5°C in first generation and +3.0°C in second generation), and transgenerational (+3.0°C for two generations) treatments. We found that levels of gonadotropin receptor gene expression (Fshr and Lhcgr) in the testes were reduced in developmental and transgenerational temperature treatments, but were similar to control levels in the step treatment. This suggests Fshr and Lhcgr may be involved in regulating male reproductive capacity in A. polyacanthus. In addition, lower Fshb expression in the brain of females in all temperature treatments compared to control, suggests that Fshb expression, which is involved in vitellogenesis, is sensitive to high temperatures. Our results help elucidate key genes that facilitate successful reproduction in reef fishes when they experience a gradual increase in temperature across generations consistent with the trajectory of climate change.

  10. Evaluation of lignins from side-streams generated in an olive tree pruning-based biorefinery: Bioethanol production and alkaline pulping.

    Science.gov (United States)

    Santos, José I; Fillat, Úrsula; Martín-Sampedro, Raquel; Eugenio, María E; Negro, María J; Ballesteros, Ignacio; Rodríguez, Alejandro; Ibarra, David

    2017-12-01

    In modern lignocellulosic-based biorefineries, carbohydrates can be transformed into biofuels and pulp and paper, whereas lignin is burned to obtain energy. However, a part of lignin could be converted into value-added products including bio-based aromatic chemicals, as well as building blocks for materials. Then, a good knowledge of lignin is necessary to define its valorisation procedure. This study characterized different lignins from side-streams produced from olive tree pruning bioethanol production (lignins collected from steam explosion pretreatment with water or phosphoric acid as catalysts, followed by simultaneous saccharification and fermentation process) and alkaline pulping (lignins recovered from kraft and soda-AQ black liquors). Together with the chemical composition, the structure of lignins was investigated by FTIR, 13 C NMR, and 2D NMR. Bioethanol lignins had clearly distinct characteristics compared to pulping lignins; a certain number of side-chain linkages (mostly alkyl-aryl ether and resinol) accompanied with lower phenolic hydroxyls content. Bioethanol lignins also showed a significant amount of carbohydrates, mainly glucose and protein impurities. By contrast, pulping lignins revealed xylose together with a dramatical reduction of side-chains (some resinol linkages survive) and thereby higher phenol content, indicating rather severe lignin degradation during alkaline pulping processes. All lignins showed a predominance of syringyl units. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. A Histopathological Study of Direct Pulp Capping with Adhesive Resins

    Directory of Open Access Journals (Sweden)

    J. Salhenejad

    2004-12-01

    Full Text Available Statement of Problem: Recently, it has been proposed that different adhesive materials can be used for direct pulp capping. Previous studies have demonstrated that multi steps dentin adhesives could form reparative dentin similar to calcium hydroxide (CH.Purpose: The aim of this study was to evaluate the histological pulp response of ninety mechanically exposed cat pulps to two adhesive resins (Scotch Bond MP and Single Bond 3M were compared with a calcium hydroxide cement (Dycal, Dentsply.Materials and Methods : Class V facial cavities with similar pulpal exposures were prepared in canines. In the experimental groups phosphoric acid was used to etch the enamel and dentin and pulp exposure, and after it dentin adhesives was applied. The exposure point of the control group was capped with Dycal then the remainder of the cavities was etched and a dentin adhesive (single bond was applied. All of the cavities were restored with a composite resin (Z 100 in usual manner. The animals were scarified after 7, 30 and 60 days (n=30, and the pulp evaluated histologically, statistical analysis was carried out with Kruskal- Wallis test (a=0.05.Results: The data showed that most of the cases had mild inflammation of pulp tissue.There was no significant difference in inflammatory reaction of pulp by Dycal and two adhesive systems, severe inflammatory reaction of pulp was observed only in most of the 30- day Single Bond group. Soft tissue organization of dentin bridge was less than ScotchBond and Dycal groups, the differentiation of dentin bridge was less than Scotch Bond group after 7 days.Conclusion: Slight inflammatory cell infiltration was the main reaction of exposed pulp when two commercially available adhesive resins were placed directly on the exposed pulp.There was no significant difference in inflammatory reaction of pulp between Dycal and two adhesive systems after 7 days and 60 days. After 7 days most of the specimens showed an amount of predentin

  12. Generation and reactivity of ketyl radicals with lignin related structures. On the importance of the ketyl pathway in the photoyellowing of lignin containing pulps and papers.

    Science.gov (United States)

    Fabbri, Claudia; Bietti, Massimo; Lanzalunga, Osvaldo

    2005-04-01

    [reaction: see text] Ketyl radicals with lignin related structures have been generated by means of radiation chemical and photochemical techniques. In the former studies ketyl radicals are produced by reaction of alpha-carbonyl-beta-aryl ether lignin models with the solvated electron produced by pulse radiolysis of an aqueous solution at pH 6.0. The UV-vis spectra of ketyl radicals are characterized by three main absorption bands. The shape and position of these bands slightly change when the spectra are recorded in alkaline solution (pH 11.0) being now assigned to the ketyl radical anions and a pKa = 9.5 is determined for the 1-(3,4,5-trimethoxyphenyl)-2-phenoxyethanol-1-yl radical. Decay rates of ketyl radicals are found to be dose dependent and, at low doses, lie in the range (1.7-2.7) x 10(3) s(-1). In the presence of oxygen a fast decay of the ketyl radicals is observed (k2 = 1.8-2.7 x 10(9) M(-1) s(-1)) that is accompanied by the formation of stable products, i.e., the starting ketones. In the photochemical studies ketyl radicals have been produced by charge-transfer (CT) photoactivation of the electron donor-acceptor salts of methyl viologen (MV2+) with alpha-hydroxy-alpha-phenoxymethyl-aryl acetates. This process leads to the instantaneous formation of the reduced acceptor (methyl viologen radical cation, MV+*), as is clearly shown in a laser flash photolysis experiment by the two absorption bands centered at 390 and 605 nm, and an acyloxyl radical [ArC(CO2*))(OH)CH2(OC6H5)], which undergoes a very fast decarboxylation with formation of the ketyl radicals. Steady-state photoirradiation of the CT ion pairs indicates that 1-aryl-2-phenoxyethanones are formed as primary photoproducts by oxidation of ketyl radicals by MV2+ (under argon) or by molecular oxygen. Small amounts of acetophenones are formed by further photolysis of 1-aryl-2-phenoxyethanones and not by beta-fragmentation of the ketyl radicals. The high reactivity of ketyl radicals with oxygen coupled

  13. Dental pulp stem cells

    DEFF Research Database (Denmark)

    Ashri, N. Y.; Ajlan, S. A.; Aldahmash, Abdullah M.

    2015-01-01

    scaffold, and guided through signaling molecules. Dental pulp stem cells have been used in an increasing number of studies in dental tissue engineering. Those cells show mesenchymal (stromal) stem cell-like properties including self-renewal and multilineage differentiation potentials, aside from...... an updated review on dental pulp stem cells and their applications in periodontal regeneration, in combination with different scaffolds and growth factors....

  14. Competitiveness of wood pulp production in different Brazilian states

    Directory of Open Access Journals (Sweden)

    Naisy Silva Soares

    2013-06-01

    Full Text Available This work aimed to analyze the competitiveness of wood pulp production in different Brazilian states, in May, 2008 (Minas Gerais, São Paulo, Espírito Santo and Bahia, using the Policy Analysis Matrix (PAM. The results obtained indicated that the private and social profitability of wood pulp production and commercialization was positive and greater in Bahia. The Brazilian companies were penalized by public policies adopted for the sector; the wood pulp production in São Paulo and Bahia were more competitive and less exposed to the negative effects of public policies that reduce the national company profits.

  15. Gamma ray induced chromophore modification of softwood thermomechanical pulp

    International Nuclear Information System (INIS)

    Robert, S.; Daneault, C.; Viel, C.; Lepine, F.

    1992-01-01

    This study focuses on bleaching a softwood (black spruce, balsam fur) thermomechanical pulp with gamma rays. Gamma rays are known for their enormous penetrating power, along with their ionizing properties. They can generate highly energetic radicals capable of oxidizing lignin chromophores. The authors studied the influence of isopropyl alcohol, sodium borohydride, oxygen, hydrogen peroxide, nitrogen dioxide and water along with gamma ray irradiation of the pulps. The authors measured the optimal dose and dose rate, along with the influence of the radical scavengers like oxygen on the bleaching effect of gamma irradiated pulps. They observe various degrees of bleaching of these pulps. Evidence relates this bleaching to the generation of perhydroxyl anions upon irradiation of water. Also, they were able to pinpoint the influence of the dose rate on the rate of formation and disappearance of these perhydroxyl anions and their influence on bleaching kinetics. Stability toward photoyellowing, and photoyellowing's kinetic of papers from these pulps was also studied

  16. Differential cardiac effects in rats exposed to atmospheric smog generated from isoprene versus toluene

    Science.gov (United States)

    The results of this study demonstrate that atmospheric smog generated from both isoprene and toluene cause cardiac effects in rats. In addition, it appears that smog from toluene is more toxic in terms of cardiac arrhythmogenicity. Smog, which is a comple...

  17. Dental pulp stem cells in regenerative dentistry.

    Science.gov (United States)

    Casagrande, Luciano; Cordeiro, Mabel M; Nör, Silvia A; Nör, Jacques E

    2011-01-01

    Stem cells constitute the source of differentiated cells for the generation of tissues during development, and for regeneration of tissues that are diseased or injured postnatally. In recent years, stem cell research has grown exponentially owing to the recognition that stem cell-based therapies have the potential to improve the life of patients with conditions that span from Alzheimer's disease to cardiac ischemia to bone or tooth loss. Growing evidence demonstrates that stem cells are primarily found in niches and that certain tissues contain more stem cells than others. Among these tissues, the dental pulp is considered a rich source of mesenchymal stem cells that are suitable for tissue engineering applications. It is known that dental pulp stem cells have the potential to differentiate into several cell types, including odontoblasts, neural progenitors, osteoblasts, chondrocytes, and adipocytes. The dental pulp stem cells are highly proliferative. This characteristic facilitates ex vivo expansion and enhances the translational potential of these cells. Notably, the dental pulp is arguably the most accessible source of postnatal stem cells. Collectively, the multipotency, high proliferation rates, and accessibility make the dental pulp an attractive source of mesenchymal stem cells for tissue regeneration. This review discusses fundamental concepts of stem cell biology and tissue engineering within the context of regenerative dentistry.

  18. Characterization of Coronal Pulp Cells and Radicular Pulp Cells in Human Teeth.

    Science.gov (United States)

    Honda, Masaki; Sato, Momoko; Toriumi, Taku

    2017-09-01

    Dental pulp has garnered much attention as an easily accessible postnatal tissue source of high-quality mesenchymal stem cells (MSCs). Since the discovery of dental pulp stem cells (DPSCs) in permanent third molars, stem cells from human exfoliated deciduous teeth and from supernumerary teeth (mesiodentes) have been identified as a population distinct from DPSCs. Dental pulp is divided into 2 parts based on the developing stage: the coronal pulp and the radicular pulp. Root formation begins after the crown part is completed. We performed a sequential study to examine the differences between the characteristics of coronal pulp cells (CPCs) and radicular pulp cells (RPCs) from permanent teeth, mesiodentes, and deciduous teeth. Interestingly, although we have not obtained any data on the difference between CPCs and RPCs in permanent teeth, there are some differences between the characteristics of CPCs and RPCs from mesiodentes and deciduous teeth. The MSC characteristics differed between the RPCs and CPCs, and the reprogramming efficiency for the generation of induced pluripotent stem cells was greater in RPCs than in CPCs from deciduous teeth. The proportion of CD105 + cells in CPCs versus that in RPCs varied in mesiodentes but not in permanent teeth. The results indicate that the proportion of CD105 + cells is an effective means of characterizing dental pulp cells in mesiodentes. Taken together, the stem cells in deciduous and supernumerary teeth share many characteristics, such as a high proliferation rate and an immunophenotype similar to that of DPSCs. Thus, mesiodentes accidentally encountered on radiographs by the general dental practitioner might be useful for stem cell therapy. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  19. Microvascular pressure responses of second-generation rats chronically exposed to 2 g centrifugation

    Science.gov (United States)

    Richardson, D. R.; Knapp, C. F.

    1977-01-01

    Preliminary results are presented for a study aimed at a quantitative comparison of microvascular dynamics in second-generation rats reared in a 2-g force field produced by centrifugation with similar data from animals reared in a centrifuge that produced only a 1-g force. It is shown that the pressure distribution in the mesenteric microvasculature of the second generation of rats reared in a 2-g environment, as well as the animals' blood pressure response to epinephrine, are significantly different compared to their 1-g counterparts. In particular, 1-g and 2-g chronic centrifugation enhances the arterial blood pressure, and the 2-g force field attenuates the pressor effects of norepinephrine.

  20. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Lei Hu

    2017-01-01

    Full Text Available Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

  1. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration.

    Science.gov (United States)

    Hu, Lei; Gao, Zhenhua; Xu, Junji; Zhu, Zhao; Fan, Zhipeng; Zhang, Chunmei; Wang, Jinsong; Wang, Songlin

    2017-01-01

    Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM) is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental pulp ECM from swine and evaluated whether it could mediate pulp regeneration. Dental pulps were acquired from the mandible anterior teeth of swine 12 months of age and decellularized with 10% sodium dodecyl sulfate (SDS) combined with Triton X-100. Pulp regeneration was conducted by seeding human dental pulp stem cells into decellularized pulp and transplanted subcutaneously into nude mice for 8 weeks. The decellularized pulp demonstrated preserved natural shape and structure without any cellular components. Histological analysis showed excellent ECM preservation and pulp-like tissue, and newly formed mineralized tissues were regenerated after being transplanted in vivo. In conclusion, decellularized swine dental pulp maintains ECM components favoring stem cell proliferation and differentiation, thus representing a suitable scaffold for improving clinical outcomes and functions of teeth with dental pulp diseases.

  2. Using renewable sources in the pulp and paper mills

    International Nuclear Information System (INIS)

    Hazi, Aneta; Hazi, Gheorghe

    2007-01-01

    The pulp and paper industry is a major consumer of natural sources (wood) and energy (fossil fuels, electricity) and a significant contributor of pollutant discharges to the environment. In this paper there are presented pulp and paper making process and steam and power generation using renewable sources. This paper includes also an exergy analysis of the steam and power generation process for a pulp and paper mill. Based on the analysis, two sustainability indicators were calculated: the exergetic efficiency and the exergy renewability. (authors)

  3. Biomechanical pulping of kenaf

    Science.gov (United States)

    Aziz Ahmed; Masood Akhtar; Gary C. Myers; Gary M. Scott

    1999-01-01

    The objective of this study was to investigate the effect of fungal pretreatment of whole kenaf prior to refining on refiner electrical energy consumption, paper strength, and optical properties. We also explored the suitability of whole kenaf biomechanical pulp for making newsprint in terms of ISO brightness and strength properties. Kenaf was sterilized by autoclaving...

  4. Infection and Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Sahng G. Kim

    2016-03-01

    Full Text Available The regeneration of the pulp-dentin complex has been a great challenge to both scientists and clinicians. Previous work has shown that the presence of prior infection may influence the characteristics of tissues formed in the root canal space after regenerative endodontic treatment. The formation of ectopic tissues such as periodontal ligament, bone, and cementum has been observed in the root canal space of immature necrotic teeth with apical periodontitis, while the regeneration of dentin and pulp has been identified in previously non-infected teeth. The current regenerative endodontic therapy utilizes disinfection protocols, which heavily rely on chemical irrigation using conventional disinfectants. From a microbiological point of view, the current protocols may not allow a sufficiently clean root canal microenvironment, which is critical for dentin and pulp regeneration. In this article, the significance of root canal disinfection in regenerating the pulp-dentin complex, the limitations of the current regenerative endodontic disinfection protocols, and advanced disinfection techniques designed to reduce the microorganisms and biofilms in chronic infection are discussed.

  5. HYDROGEN PEROXIDE BLEACHING OF CMP PULP USING MAGNESIUM HYDROXIDE

    Directory of Open Access Journals (Sweden)

    Farhad Zeinaly

    2009-11-01

    Full Text Available Conventional bleaching of hardwood CMP pulp with magnesium hydroxide (Mg(OH2 show significant benefits over bleaching with sodium hydroxide (NaOH under various conditions. Magnesium hydroxide bleaching generate higher optical properties, higher pulp yield and lower effluent COD at the same chemical charge, but the physical properties were found to be similar for both processes. The initial freeness of the bleached pulps and refining value to reach a target freeness (about 350 ml. CSF were more for the Mg(OH2-based process. The residual peroxide of filtrate from the Mg(OH2-based process was very high as compared to conventional bleaching.

  6. Enzyme Enhanced Protein Recovery from Green Biomass Pulp

    DEFF Research Database (Denmark)

    Dotsenko, Gleb; Lange, Lene

    2017-01-01

    of local protein resources based on upgrade from e.g. green plant biomass. In present work we consider different strategies for protein recovery from white clover and ryegrass screw press pulps, using aqueous extraction, as well as carbohydrases and proteases enhanced extraction. Protein recovery...... in these studies was determined as a yield of solubilized protein with regard to the total protein in a screw press pulp. Aqueous extraction at pH 8.0 resulted in approx. 40 % protein recovery, while proteases application (Savinase 16.0L, Novozymes) enabled twice higher protein yield. Application of plant cell...... pulp proteolyzates, generated by Savinase 16.0L protease....

  7. Radiosensitivity of apricot budsticks exposed to acute gamma rays and nursery observations on the second vegetative generation from irradiated buds

    International Nuclear Information System (INIS)

    Legave, J.M.; Garcia, G.

    1988-01-01

    Varietal improvement is essential if a new impetus is to be given to the French apricot crop. We have accordingly started a mutation breeding programme by bud irradiation. Because of the scarcity of bibliographical data, the first step was to study the budwood radiosensitivity of the apricot cultivars used as starting material. Budsticks of various cultivars were exposed to increasing doses of acute gamma rays. The physiological effects induced by irradiation were evaluated from bud survival and growth. These results allowed us, in the first instance, to fix the optimal dose range for dormant buds irradiated at 6 to 7 Gy/mm. Observations in the nursery on scions from the second vegetative generation (V2) already showed the limits of bud irradiation. Further observations in the orchard are need to estimate the value of this method for apricot breeding [fr

  8. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration

    OpenAIRE

    Keller, Laetitia; Offner, Damien; Schwint?, Pascale; Morand, David; Wagner, Quentin; Gros, Catherine; Bornert, Fabien; Bahi, Sophie; Musset, Anne-Marie; Benkirane-Jessel, Nadia; Fioretti, Florence

    2015-01-01

    The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be p...

  9. Tritium in organic compounds of brain of rats exposed to tritiated water or tritiated food during three successive generations

    International Nuclear Information System (INIS)

    Major, Z.

    1987-01-01

    The study was performed on Wistar rats which were chronically exposed to tritiated water (HTO, 37.0 kBq/ml) or to tritiated food (48.1 kBq/g). The tritium exposure of the rats was started before mating and was continued up to delivery of the F 3 generation. The incorporation of organically bound tritium (OBT) was determined in whole brain and in some organic components of rats at various ages. The specific activity of OBT in whole brain and in its organic components with the exception of proteins significantly increased in the F 1 +F 2 generations of rats in comparison with F 0 females. The contribution of OBT to the total dose rate was about 6 per cent in HTO group and 9 per cent in T-food group. The contribution of lipids and proteins to the dose rate from OBT was similar in both treatment groups, being 60 and 20 per cent, respectively. 20 refs. (author)

  10. Dentin and pulp sense cold stimulus.

    Science.gov (United States)

    Tokuda, Masayuki; Tatsuyama, Shoko; Fujisawa, Mari; Morimoto-Yamashita, Yoko; Kawakami, Yoshiko; Shibukawa, Yoshiyuki; Torii, Mistuso

    2015-05-01

    Dentin hypersensitivity is a common symptom, and recent convergent evidences have reported transient receptor potential (TRP) channels in odontoblasts act as mechanical and thermal molecular sensor, which detect stimulation applied on the exposed dentin surface, to drive multiple odontoblastic cellular functions, such as sensory transduction and/or dentin formation. In the present study, we confirmed expression of TRP melastatin subfamily member-8 (TRPM8) channels in primary cultured cells derived from human dental pulp cells (HPCs) and mouse odontoblast-lineage cells (OLCs) as well as in dentin matrix protein-1 (DMP-1) and dentin sialoprotein (DSP) positive acutely isolated rat odontoblasts from dental pulp tissue slice culture by immunohistochemical analyses. In addition, we detected TRPM8 channel expression on HPCs and OLCs by RT-PCR and Western blotting analyses. These results indicated that both odontoblasts and dental pulp cells express TRPM8 channels in rat, mouse and human, and therefore we hypothesize they may contribute as cold sensor in tooth. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Rubidium uptake by mouse pancreatic islets exposed to 6-hydroxydopamine, ninhydrin, or other generators of hydroxyl radicals

    Energy Technology Data Exchange (ETDEWEB)

    Grankvist, K.; Sehlin, J.; Taeljedal, I.-B.

    1986-01-01

    The purpose was to study the toxicity of drugs known to generate free radicals on isolated pancreatic islets. The accumulation of /sup 86/Rb/sup +/ by mouse pancreatic islets was measured in vitro. Exposing the islets to 6-hydroxydopamine, minhydrin, or phenazine methosulphate + NADH inhibited the Rb/sup +/ uptake, whereas paraquat or acetylphenylhydrazine had no effect. This effect of 6-hydroxydopamine was prevented by either of the hydroxyl radical scavengers, sodium benzoate and mannitol, but not by the non-scavenger urea; ninhydrin was partially protected against by mannitol but not by benzoate. Protection against 6-hydroxydopamine was also afforded by D-glucose but not by L-glucose or 3-O-methyl-D-glucose; none of the sugars protected against ninhydrin. In damaging islet beta-cells and in being protected against by D-glucose, 6-hydroxydopamine closely resembles the diabetogenic drug, alloxan. It is suggested that protection against alloxan may involve both glucose metabolism and the interaction of glucose with its membrane-located carrier, while protection against 6-hydroxydopamine appears to be unrelated to the hexose carrier mechanism.

  12. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration.

    Science.gov (United States)

    Keller, Laetitia; Offner, Damien; Schwinté, Pascale; Morand, David; Wagner, Quentin; Gros, Catherine; Bornert, Fabien; Bahi, Sophie; Musset, Anne-Marie; Benkirane-Jessel, Nadia; Fioretti, Florence

    2015-11-05

    The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

  13. Active Nanomaterials to Meet the Challenge of Dental Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Laetitia Keller

    2015-11-01

    Full Text Available The vitality of the pulp is fundamental to the functional life of the tooth. For this aim, active and living biomaterials are required to avoid the current drastic treatment, which is the removal of all the cellular and molecular content regardless of its regenerative potential. The regeneration of the pulp tissue is the dream of many generations of dental surgeons and will revolutionize clinical practices. Recently, the potential of the regenerative medicine field suggests that it would be possible to achieve such complex regeneration. Indeed, three crucial steps are needed: the control of infection and inflammation and the regeneration of lost pulp tissues. For regenerative medicine, in particular for dental pulp regeneration, the use of nano-structured biomaterials becomes decisive. Nano-designed materials allow the concentration of many different functions in a small volume, the increase in the quality of targeting, as well as the control of cost and delivery of active molecules. Nanomaterials based on extracellular mimetic nanostructure and functionalized with multi-active therapeutics appear essential to reverse infection and inflammation and concomitantly to orchestrate pulp cell colonization and differentiation. This novel generation of nanomaterials seems very promising to meet the challenge of the complex dental pulp regeneration.

  14. Temperature variation in pulp chamber during dental bleaching in presence or absence of light activation

    OpenAIRE

    Mollica, Fernanda Brandão; Rocha, Daniel Maranha da; Travassos, Alessandro Caldas; Valera, Marcia Carneiro; Araujo, Maria Amélia Maximo de

    2010-01-01

    PURPOSE: In addition to the chemical damage due to bleaching gels penetration into the pulp during pulp vitality dental bleaching, another possible aggressive factor could be the heat generated by the exothermal oxidation reaction of the bleaching gel, which may also be aggravated by the use of light activation. This study assessed the temperature variation in the pulp chamber in human teeth, using three different bleaching gels with or without LED light activation. METHODS: Thirty human pre-...

  15. Obtaining value prior to pulping with diethyl oxalate and oxalic acid

    Science.gov (United States)

    W.R. Kenealy; E. Horn; C.J. Houtman; J. Laplaza; T.W. Jeffries

    2007-01-01

    Pulp and paper are converted to paper products with yields of paper dependent on the wood and the process used. Even with high yield pulps there are conversion losses and with chemical pulps the yields approach 50%. The portions of the wood that do not provide product are either combusted to generate power and steam or incur a cost in waste water treatment. Value prior...

  16. Caracterização tecnológica, para produção de celulose, da nova geração de clones de Eucalyptus do Brasil Technological characterization of the new generation of Eucalyptus clones in Brazil for kraft pulp production

    Directory of Open Access Journals (Sweden)

    José Lívio Gomide

    2005-02-01

    Full Text Available Foram analisados clones de Eucalyptus de última geração, pertencentes às principais empresas brasileiras de celulose. Os estudos consistiram numa caracterização tecnológica detalhada da qualidade das madeiras utilizadas no processamento fabril das empresas. Foram realizadas análise químicas detalhadas das madeiras e cozimentos kraft, simulando-se uma das modernas técnica de digestor contínuo. Os resultados indicaram a alta qualidade dos clones de Eucalyptus atualmente plantados no Brasil para produção de celulose.Last generation of Eucalyptus clones pulped by the main Brazilian kraft pulp mills were used for this study. Detailed chemical analysis of the woods were carried out to establish the wood quality. Laboratory simulation of a modern continuous digester technique was used for pulp production. Results demonstrated the high quality of Eucalyptus clones wood that are being planted in Brazil for kraft pulp production.

  17. Effects on circulating steroid hormones and gene expression along the hypothalamus–pituitary–gonadal axis in adult Japanese quail exposed to 17β-trenbolone across multiple generations

    Science.gov (United States)

    Karouna-Renier, Natalie K.; Chen, Yu; Henry, Paula F.; Maddox, Catherine M.; Sprague, Dan

    2017-01-01

    We investigated the effects of the androgenic growth promoter 17β-trenbolone (17βTB) on adult Japanese quail (Coturnix japonica) exposed across three generations. The F0 generation was exposed after sexual maturity to 0, 1, 5, 10, 20, and 40 ppm through feed. The F1 generation was exposed in ovo by maternal transfer and through feed at the same doses as their parents. The F2 generation was exposed in ovo only. Levels of plasma sex steroids, gonadal Cytochrome P450 aromatase (CYP19A1) mRNA and select brain neuroendocrine peptide mRNAs were measured. In males, testosterone levels did not differ in any generation from those in controls. Estradiol was significantly elevated in 17βTB treated F0 and F1 males. In F0 and F1 females, testosterone was suppressed by 17βTB, whereas estradiol was significantly higher at 40 ppm in F0 and at 10 ppm in F1 females. CYP19A1 expression in F1 males and females increased suggesting a compensatory response to the androgenic effects of 17βTB. Few significant effects were observed in the F2 birds indicating that in ovo exposure had limited effects on the monitored endpoints. Overall, our results confirmed endocrine disrupting effects of dietary 17βTB in Japanese quail but the response was dependent on sex, developmental stage at initiation of exposure, and dose.

  18. Is Pulp Inflammation a Prerequisite for Pulp Healing and Regeneration?

    Directory of Open Access Journals (Sweden)

    Michel Goldberg

    2015-01-01

    Full Text Available The importance of inflammation has been underestimated in pulpal healing, and in the past, it has been considered only as an undesirable effect. Associated with moderate inflammation, necrosis includes pyroptosis, apoptosis, and nemosis. There are now evidences that inflammation is a prerequisite for pulp healing, with series of events ahead of regeneration. Immunocompetent cells are recruited in the apical part. They slide along the root and migrate toward the crown. Due to the high alkalinity of the capping agent, pulp cells display mild inflammation, proliferate, and increase in number and size and initiate mineralization. Pulp fibroblasts become odontoblast-like cells producing type I collagen, alkaline phosphatase, and SPARC/osteonectin. Molecules of the SIBLING family, matrix metalloproteinases, and vascular and nerve mediators are also implicated in the formation of a reparative dentinal bridge, osteo/orthodentin closing the pulp exposure. Beneath a calciotraumatic line, a thin layer identified as reactionary dentin underlines the periphery of the pulp chamber. Inflammatory and/or noninflammatory processes contribute to produce a reparative dentinal bridge closing the pulp exposure, with minute canaliculi and large tunnel defects. Depending on the form and severity of the inflammatory and noninflammatory processes, and according to the capping agent, pulp reactions are induced specifically.

  19. A substitute model of two-dimensional dry friction exposed to dither generated by rolling contact of wheel and rail

    Science.gov (United States)

    Piotrowski, Jerzy

    2012-10-01

    Dither generated by rolling contact of wheel and rail smoothes dry friction damping provided by the primary suspension dampers of freight wagons and it should be taken into account in numerical simulations. But numerically the problem is non-smooth and this leads to long execution time during simulation, especially when the vehicle with friction dampers is modelled in the environment of an multi-body system simulation program, whose solver has to cope with many strong non-linearities. The other difficulty is the necessity of handling within the code a number of big volume files of recorded dither sampled with high frequency. To avoid these difficulties, a substitute model of two-dimensional dry friction exposed to dither is proposed that does not need application of dither during simulation, but it behaves as if dither were applied. Due to this property of the model, the excitation of the vehicle model by track irregularities may be supplied as low-frequency input, which allows fast execution and, the necessity of handling high-volume files of recorded dither is avoided. The substitute model is numerically effective. To identify parameters of the substitute model, a pre-processing employing a sample of the realistic dither is carried-out on a simple two-degrees-of-freedom system. The substitute model is anisotropic, describing anisotropic properties of the two-dimensional friction arising in the presence of one-dimensional dither. The model may be applied in other branches of engineering, for example, in mechatronics and robotics, where application of dither may improve the accuracy of positioning devices.

  20. Pulp-dentin Regeneration: Current State and Future Prospects.

    Science.gov (United States)

    Cao, Y; Song, M; Kim, E; Shon, W; Chugal, N; Bogen, G; Lin, L; Kim, R H; Park, N-H; Kang, M K

    2015-11-01

    The goal of regenerative endodontics is to reinstate normal pulp function in necrotic and infected teeth that would result in reestablishment of protective functions, including innate pulp immunity, pulp repair through mineralization, and pulp sensibility. In the unique microenvironment of the dental pulp, the triad of tissue engineering would require infection control, biomaterials, and stem cells. Although revascularization is successful in resolving apical periodontitis, multiple studies suggest that it alone does not support pulp-dentin regeneration. More recently, cell-based approaches in endodontic regeneration based on pulpal mesenchymal stem cells (MSCs) have demonstrated promising results in terms of pulp-dentin regeneration in vivo through autologous transplantation. Although pulpal regeneration requires the cell-based approach, several challenges in clinical translation must be overcome-including aging-associated phenotypic changes in pulpal MSCs, availability of tissue sources, and safety and regulation involved with expansion of MSCs in laboratories. Allotransplantation of MSCs may alleviate some of these obstacles, although the long-term stability of MSCs and efficacy in pulp-dentin regeneration demand further investigation. For an alternative source of MSCs, our laboratory developed induced MSCs (iMSCs) from primary human keratinocytes through epithelial-mesenchymal transition by modulating the epithelial plasticity genes. Initially, we showed that overexpression of ΔNp63α, a major isoform of the p63 gene, led to epithelial-mesenchymal transition and acquisition of stem characteristics. More recently, iMSCs were generated by transient knockdown of all p63 isoforms through siRNA, further simplifying the protocol and resolving the potential safety issues of viral vectors. These cells may be useful for patients who lack tissue sources for endogenous MSCs. Further research will elucidate the level of potency of these iMSCs and assess their

  1. Depth and activity of carious lesions as indicators for the regenerative potential of dental pulp after intervention

    DEFF Research Database (Denmark)

    Bjørndal, Lars; Pedersen, Sune Demant Nørgaard; Dabelsteen, Sally

    2014-01-01

    that the typical reason for performing endodontic treatment is deep caries. The biological concept of vital pulp therapy associated with deep caries takes the treatment and evaluation of the unexposed as well as the exposed pulp into account. Interestingly, the clinical diagnosis is typically the same. Deep caries...

  2. Chapter 6: Prehydrolysis Pulping with Fermentation Coproducts

    Science.gov (United States)

    T.H. Wegner; C.J. Houtman; A.W. Rudie; B.L. Illman; P.J. Ince; E.M. Bilek; T.W. Jeffries

    2013-01-01

    Although the term “integrateed biorefinery” is new, the concept has long been familiar to the pulp and paper industry, where processes include biomass boilers providing combined heat and power, and byproducts of pulping include turpentine, fatty acids and resin acids. In the dominant kraft (or sulfate) pulping process, dissolved lignin and chemicals from the pulp...

  3. Decellularized Swine Dental Pulp as a Bioscaffold for Pulp Regeneration

    OpenAIRE

    Hu, Lei; Gao, Zhenhua; Xu, Junji; Zhu, Zhao; Fan, Zhipeng; Zhang, Chunmei; Wang, Jinsong; Wang, Songlin

    2017-01-01

    Endodontic regeneration shows promise in treating dental pulp diseases; however, no suitable scaffolds exist for pulp regeneration. Acellular natural extracellular matrix (ECM) is a favorable scaffold for tissue regeneration since the anatomical structure and ECM of the natural tissues or organs are well-preserved. Xenogeneic ECM is superior to autologous or allogeneic ECM in tissue engineering for its unlimited resources. This study investigated the characteristics of decellularized dental p...

  4. CD146 positive human dental pulp stem cells promote regeneration of dentin/pulp-like structures.

    Science.gov (United States)

    Matsui, Mikiko; Kobayashi, Tomoko; Tsutsui, Takeo W

    2018-04-01

    CD146 and STRO-1 are endothelial biomarkers that are co-expressed on the cellular membranes of blood vessels within human dental pulp tissue. This study characterized the percentage of dentin-like structures produced by CD146-positive (CD146 + ) human dental pulp stem cells (DPSCs), compared with their CD146-negative (CD146 - ) counterparts. DPSC populations were enriched using magnetic-activated cell sorting (MACS), yielding CD146 + and CD146 - cells, as well as mixtures composed of 25% CD146 + cells and 75% CD146 - cells (CD146 +/- ). Cell growth assays indicated that CD146 + cells exhibit an approximate 3-4 h difference in doubling time, compared with CD146 - cells. Cell cycle distributions were determined by flow cytometry analysis. The low percentage of CD146 + cells' DNA content in G 0 /G 1 phase were compared with CD146 - and non-separated cells. In contrast to CD146 - and non-separated cells, prompt mineralization was observed in CD146 + cells. Subsequently, qRT-PCR revealed high mRNA expression of CD146 and Alkaline phosphatase in mineralization-induced CD146 + cells. CD146 + cells were also observed high adipogenic ability by Oil red O staining. Histological examinations revealed an increased area of dentin/pulp-like structures in transplanted CD146 + cells, compared with CD146 - and CD146 +/- cells. Immunohistochemical studies detected dentin matrix protein-1 (DMP1) and dentin sialophosphoprotein (DSPP), as well as human mitochondria, in transplanted DPSCs. Co-expression of CD146 and GFP indicated that CD146 was expressed in transplanted CD146 + cells. CD146 + cells may promote mineralization and generate dentin/pulp-like structures, suggesting a role in self-renewal of stem cells and dental pulp regenerative therapy.

  5. Effects of bleaching agents and adhesive systems in dental pulp: a literature review

    OpenAIRE

    Oliveira, Maria Antonieta Veloso Carvalho de; Quagliatto, Paulo Sérgio; Magalhães, Denildo; Biffi, João Carlos Gabrielli

    2012-01-01

    The dental pulp may be exposed to several irritants that are potentially noxious to the health and functions of this tissue. Each type of irritant or injury has different effects on the pulp, which are generally characterized by acute inflammation, chronic inflammation or necrosis. Common examples of irritants are dental caries, cavity preparation procedures, traumatic injuries, and chemical substances like bleaching agents and adhesive systems. The present study aimed to review the current k...

  6. Selection of Corymbia citriodora for pulp productivity | Brawner ...

    African Journals Online (AJOL)

    Evaluation of a series of spotted gum (Corymbia citirodora) progeny trials, established in the subtropical region of Queensland, Australia, was undertaken to provide information for the development of advanced-generation breeding populations suitable for pulp production. Measurements of growth at two ages were ...

  7. MOLYBDENUM CATALYZED ACID PEROXIDE BLEACHING OF EUCALYPTUS KRAFT PULP

    Directory of Open Access Journals (Sweden)

    Marcos S. Rabelo

    2008-08-01

    Full Text Available Molybdenum catalyzed peroxide bleaching (PMo Stage consists of pulp treatment with hydrogen peroxide under acidic conditions in the presence of a molybdenum catalyst. Molybdenum is applied in catalytic doses (50-200 mg/kg pulp and may originate from various sources, including (NH46Mo7O24.4H2O, Na2MoO4.2H2O, siliconmolybdate, etc. This work is aimed at optimizing the PMo stage and evaluating its industrial application in the OAZDP sequence. Optimum PMo stage conditions for bleaching eucalyptus pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/adt Mo and 5 kg/adt H2O2. The PMo stage was more efficient to remove pulp hexenuronic acids than lignin. Its efficiency decreased with increasing pH in the range of 1.5-5.5, while it increased with increasing temperature and peroxide and molybdenum doses. The application of the PMo stage as replacement for the A-stage of the AZDP sequence significantly decreased chlorine dioxide demand. The PMo stage caused a decrease of 20-30% in the generation of organically bound chlorine. The quality parameters of the pulp produced during the PMo stage mill trial were comparable to those obtained with the reference A-stage.

  8. C-myb Regulates Autophagy for Pulp Vitality in Glucose Oxidative Stress.

    Science.gov (United States)

    Lee, Y H; Kim, H S; Kim, J S; Yu, M K; Cho, S D; Jeon, J G; Yi, H K

    2016-04-01

    Diabetes mellitus is closely related to oral-complicated diseases by oxidative stress. This study investigates whether cellular myeloblastosis (c-myb) could protect human dental pulp cells against glucose oxidative stress and regulate autophagy activity for pulp vitality. Diabetes mellitus was induced by streptozotocin in Sprague-Dawley rats, and their pulp tissue in teeth was analyzed in terms of pulp cavity and molecules by hematoxylin and eosin and immunohistochemistry staining. Human dental pulp cells were serially subcultured and treated with glucose oxidase in the presence of elevated glucose to generate glucose oxidative stress. The replication-deficient adenovirus c-myb and small interfering RNA c-myb were introduced for c-myb expression. The pulp tissue from the diabetic rats was structurally different from normal tissue in terms of narrow pulp capacity, reduced c-myb, and dentinogenesis molecules. Glucose oxidase treatment decreased c-myb and dentinogenesis molecules (bone morphogenetic protein 2 and 7, dentin matrix protein 1, and dentin sialophosphoprotein) in human dental pulp cells. However, overexpression of c-myb by adenovirus c-myb increased dentinogenesis, autophagy molecules (autophagy protein 5, microtubule-associated protein 1A/1B-light chain 3, and Beclin-1), and cell survival via p-AMPK/AKT signaling even with glucose oxidative stress. In contrast, the lack of c-myb decreased the above molecules and cell survival by downregulating p-AMPK/AKT signaling. The results indicate that diabetes leads to irreversible damage to dental pulp, which is related to downexpression of autophagy via the p-AMPK/AKT pathway by decline of c-myb. The findings of this study provide a new insight that c-myb could ameliorate autophagy activity and that it is applicable for monitoring complicated diseases of dental pulp. The involvement of c-myb in pulp pathology could serve a therapeutic target in oral-complicated diseases. © International & American Associations

  9. Evaluation of a value prior to pulping-thermomechanical pulp business concept. Part 2.

    Science.gov (United States)

    Ted Bilek; Carl Houtman; Peter Ince

    2011-01-01

    Value Prior to Pulping (VPP) is a novel biorefining concept for pulp mills that includes hydrolysis extraction of hemicellulose wood sugars and acetic acid from pulpwood prior to pulping. The concept involves conversion of wood sugars via fermentation to fuel ethanol or other chemicals and the use of remaining solid wood material in the pulping process. This paper...

  10. Preventive endodontics by direct pulp capping with restorative dentin substitute-biodentine: A series of fifteen cases

    Directory of Open Access Journals (Sweden)

    Kavita Dube

    2018-01-01

    Full Text Available Introduction: Treatment of mechanical exposure of the pulp during caries excavation presents a clinical challenge. In this case series of 15 patients, with a follow-up period of over a year, the outcome of direct pulp capping with Biodentine (septodont after mechanical pulp exposure was assessed. Aim of Study: The aim of this study is to evaluate the outcome of direct pulp capping with Biodentine in deeply carious teeth when pulp was mechanically exposed during caries excavation and cavity preparation. Vital pulps exposed during caries excavation in molar teeth were treated with 3% sodium hypochlorite for 2 min. If adequate hemostasis was achieved, the pulp tissue was capped with Biodentine, which covered the entire pulpal floor. This was followed by the placement of a layer of resin-modified glass ionomer cement and a final layer of composite resin (Filtek Z350-3M to complete the restoration. The patients were recalled periodically and evaluated for any evidence of pulpal/periapical pathology. Results: In the follow-up period that ranged from 12 to 24 months, all teeth were asymptomatic. Conclusion: Biodentine appears to be a suitable material for direct pulp capping under clinical conditions. However, long-term follow-up studies and controlled trials involving a large sample size are warranted.

  11. Improved pulp bleaching potential of Bacillus subtilis WB800 through overexpression of three lignolytic enzymes from various bacteria.

    Science.gov (United States)

    Ozer, Aysegul; Uzuner, Ugur; Guler, Halil Ibrahim; Ay Sal, Fulya; Belduz, Ali Osman; Deniz, Ilhan; Canakci, Sabriye

    2017-12-29

    A chemical bleaching process of paper pulps gives off excessive amount of chlorinated organic wastes mostly released to environment without exposing complete bioremediaton. Recent alternative and eco-friendly approaches toward pulp bleaching appear more responsive to environmental awareness. Here we report, direct use of a recombinant Bacillus subtilis bacterium for pulp bleaching, endowed with three ligninolytic enzymes from various bacteria. In addition, efficient bleaching performance from glutathione-S-transferase (GST) biocatalyst tested for the first time in pulp bleaching applications was also achieved. Simultaneous and extracellular overproduction of highly active GST, laccase, and lignin peroxidase catalysts were also performed by Bacillus cells. Both enhanced bleaching success and improved delignification rates were identified when enzyme combinations tested on both pine kraft and waste paper pulps, ranging from 69.75% to 79.18% and 60.89% to 74.65%, respectively. Furthermore, when triple enzyme combination applied onto the papers from pine kraft and waste pulps, the best ISO brightness values were identified as 66.45% and 64.67%, respectively. The delignification rates of pulp fibers exposed to various enzymatic bleaching sequences were comparatively examined under SEM. In conclusion, the current study points out that in near future, a more fined-tuned engineering of pulp-colonizing bacteria may become a cost-effective and environmentally friendly alternative to chemical bleaching. © 2017 International Union of Biochemistry and Molecular Biology, Inc.

  12. Simultaneous production of bio-ethanol and bleached pulp from red algae.

    Science.gov (United States)

    Yoon, Min Ho; Lee, Yoon Woo; Lee, Chun Han; Seo, Yung Bum

    2012-12-01

    The red algae, Gelidium corneum, was used to produce bleached pulp for papermaking and ethanol. Aqueous extracts obtained at 100-140 °C were subjected to saccharification, purification, fermentation, and distillation to produce ethanol. The solid remnants were bleached with chlorine dioxide and peroxide to make pulp. In the extraction process, sulfuric acid and sodium thiosulfate were added to increase the extract yield and to improve de-polymerization of the extracts, as well as to generate high-quality pulp. An extraction process incorporating 5% sodium thiosulfate by dry weight of the algae provided optimal production conditions for the production of both strong pulp and a high ethanol yield. These results suggest that it might be possible to utilize algae instead of trees and starch for pulp and ethanol production, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Transient pulse analysis of ionized electronics exposed to γ-radiation generated from a relativistic electron beam

    Science.gov (United States)

    Min, Sun-Hong; Kwon, Ohjoon; Sattorov, Matlabjon; Baek, In-Keun; Kim, Seontae; Hong, Dongpyo; Jeong, Jin-Young; Jang, Jungmin; Bera, Anirban; Barik, Ranjan Kumar; Bhattacharya, Ranajoy; Cho, Ilsung; Kim, Byungsu; Park, Chawon; Jung, Wongyun; Park, Seunghyuk; Park, Gun-Sik

    2018-02-01

    When a semiconductor element is irradiated with radiation in the form of a transient pulse emitted from a nuclear explosion, a large amount of charge is generated in a short time in the device. A photocurrent amplified in a certain direction by these types of charges cause the device to break down and malfunction or in extreme cases causes them to burn out. In this study, a pulse-type γ-ray generator based on a relativistic electron beam accelerator (γ=2.2, β=0.89) which functions by means of tungsten impingement was constructed and tested in an effort to investigate the process and effects of the photocurrent formed by electron hole pairs (EHP) generated in a pMOSFET device when a transient radiation pulse is incident in the device. The pulse-type γ-ray irradiating device used here to generate the electron beam current in a short time was devised to allow an increase in the irradiation dose. A precise signal processing circuit was constructed to measure the photocurrent of the small signal generated by the pMOSFET due to the electron beam accelerator pulse signal from the large noise stemming from the electromagnetic field around the relativistic electron beam accelerator. The pulse-type γ-ray generator was installed to meet the requirements of relativistic electron beam accelerators, and beam irradiation was conducted after a beam commissioning step.

  14. Comparative pulping of sunflower stalks

    Directory of Open Access Journals (Sweden)

    Valerii Barbash

    2016-03-01

    Full Text Available The procedure of holocellulose content determination in non-wood plant raw materials was developed. The strength properties of pulp obtained from sunflower stalks by neutral-sulphite, soda, alkaline sulphite-anthraquinone-ethanol and peracetic methods of delignification were studied. Methodology of comparison of plant materials delignification methods using new lignin-carbohydrate diagram was proposed. It was shown, that the alkaline sulphite-anthraquinone-ethanol method of pulping is characterized by the highest delignification degree and is the most efficient among the studied methods

  15. PEMUTIHAN PULP DENGAN HIDROGEN PEROKSIDA

    Directory of Open Access Journals (Sweden)

    Ahmad M. Fuadi

    2012-01-01

    Full Text Available The use of bleaching agent has increased as the result of increasing of paper consumption. The conventional bleaching agent that commonly used is material containing of chlorine. This material is not environmentally friendly and should be replaced by environmentally benign chemical, such as H2O2. About 40 gram of dry Akasia pulp was mixed with 600 ml of distilled water was put into plastic bag heated in a water bath. When the temperature reached 630C, a solution of 4 % of H2O2 and distilled water was added to obtain 5 % consistency. This mixture was put into water bath and was heated for 2 hours. The same procedure was conducted with various concentration of H2O2, time and pH. At the end of the process, the pulp was dewatered and washed. The filtrate obtained from the initial dewatering was used to determine the residual of H2O2. The pulp was analyzed to determine brightness, fiber strength and kappa number. The maximum achievement of brightness was 62,1 % ISO, 6.86 of kappa number and 1.02 kg/15 mm of fiber strength, which are reached at16 % of the use of H2O2, pH 11 and 5 hours of bleaching time. This achievement is similar to bleaching result by the additional of 4% H2O2. Inefficient usage of H2O2 was caused by some metal ions in the pulp which facilitate the decomposition of H2O2 to produce oxygen and water which has not effect on increasing the brightness. To improve the bleach ability of H2O2, initial treatment to remove metal ions from pulp should be done. Seiring dengan meningkatnya kebutuhan kertas, kebutuhan bahan pemutih juga mengalami kenaikan. Saat ini bahan pemutih yang banyak digunakan adalah senyawa yang mengandung khlor. Senyawa ini sangat tidak ramah lingkungan, oleh karena itu, perlu dicari bahan yang ramah lingkungan untuk menggantikannya. Salah satunya adalah hidrogen peroksida. Pulp dari pohon akasia sebanyak 40 gram kering dicampur dengan 600 ml aquadest dimasukkan dalam kantung plastik dipanaskan dalam water bath

  16. EPR detection of hydroxyl radical generation and its interaction with antioxidant system in Carassius auratus exposed to pentachlorophenol

    Energy Technology Data Exchange (ETDEWEB)

    Luo Yi [Key Laboratory of Pollution Processes and Environmental Criteria (Nankai University), Ministry of Education, College of Environmental Sciences and Engineering, Nankai University, Tianjin 300071 (China); Wang Xiaorong, E-mail: yiyluo@gmail.com [State Key Laboratory of Pollution Control and Resources Reuse, School of Environment, Nanjing University, Nanjing 210093 (China); Ji Liangliang; Su Yan [State Key Laboratory of Pollution Control and Resources Reuse, School of Environment, Nanjing University, Nanjing 210093 (China)

    2009-11-15

    In the present study, direct evidence of hydroxyl radical production in livers of Carassius auratus exposed to pentachlorophenol (PCP) was provided using electron paramagnetic resonance (EPR) with spin-trapping. A dose-effect relationship was obtained between hydroxyl radical intensities and PCP exposure. It was observed that hydroxyl radical was significantly induced by 0.001 mg l{sup -1} (below the criteria for Chinese fishery water quality) of PCP exposure. A strong positive correlation (r = 0.9581, p < 0.001) was observed between PCP liver concentrations and hydroxyl radical intensities within 7 d of PCP exposure, which suggests that hydroxyl radical are mainly produced from PCP itself. However, no correlation was observed between PCP liver concentrations and hydroxyl radical intensities after 7 d, and a higher intensity of hydroxyl radical could still be observed when the PCP liver concentrations decreased to a lower level, which suggests that other mechanisms may possibly contribute to hydroxyl radical production after 7 d. The glutathione/oxidized glutathione (GSH/GSSG) ratio decreased below that of the control level during the entire period of PCP exposure (0.05 mg l{sup -1}), which suggested oxidative stress occurred.

  17. RBS analysis of ions implanted in light substrates exposed to hot plasmas laser-generated at PALS

    Czech Academy of Sciences Publication Activity Database

    Torrisi, L.; Gammino, S.; Picciotto, A.; Wolowski, J.; Krása, Josef; Láska, Leoš; Calcagnile, L.; Quarta, G.

    2005-01-01

    Roč. 160, 10-12 (2005), s. 685-695 ISSN 1042-0150. [Workshop PIBHI 2005 /2./. Giardini Naxos, 08.06.06-11.06.06] R&D Projects: GA MŠk(CZ) LC528 Institutional research plan: CEZ:AV0Z10100523 Keywords : RBS analysis * ion implantation * plasma-generated by lasers Subject RIV: BH - Optics, Masers, Lasers Impact factor: 0.353, year: 2005

  18. Alkaline pulping of some eucalypts from Sudan.

    Science.gov (United States)

    Khristova, P; Kordsachia, O; Patt, R; Dafaalla, S

    2006-03-01

    Four eucalypts (Eucalyptus camaldulensis, Eucalyptus microtheca, Eucalyptus tereticornis and Eucalyptus citriodora) grown in Sudan were examined for their suitability for pulping and papermaking with different alkaline methods. Their physical, morphological and chemical characteristics are reported. The pulping trials with E. citriodora and E. tereticornis were carried out using the kraft-AQ, soda-AQ, modified AS/AQ (ASA), ASAM and kraft methods. For the other two species, only the ASAM and the kraft process were applied. ASAM pulping gave the best results in terms of yield, degree of delignification, mechanical and optical pulp properties. The best pulps, obtained in kraft and ASAM cooking of E. citriodora, were bleached to 88% ISO brightness in a totally chlorine free bleaching sequence (OQ1O/PQ2P). The bleached pulps, especially the ASAM pulp, showed good papermaking properties and would be suitable for manufacture of writing and printing grades of paper.

  19. Chronic radiation exposure: possibility of studying mutation process in generations based on the established DNA bank of exposed individuals and their offspring

    International Nuclear Information System (INIS)

    Rusinova, Galina G.; Adamova, Galina V.; Dudchenko, Natalya N.; Azizova, Tamara V.; Kurbatov, Andrey V.

    2002-01-01

    Data were summarized on the DNA Bank establishment for workers of the Mayak nuclear facility in Southern Ural, who were exposed to different doses of chronic radiation from γ -rays during the first years of the enterprise operations (1948-1958) and their families. Some workers were exposed to combined radiation (external + internal radiation from incorporated 239 Pu). The DNA Bank was established to store the unique genetic material from these individuals and their offspring for future risk estimation of the late consequences of radiation exposure using modern molecular-genetic technologies. Today, DNA Bank contains genetic material from 1,500 individuals and 218 families. The computer database was generated for the DNA Bank. It included individual medical-demographic, occupational descriptions and doses, quantitative and qualitative DNA data. Literature data on radiation-induced genome instability (variability of hypervariable areas) were also analyzed. Prospects of the DNA Bank establishment are also presented. The work is carried out on extension of the DNA Bank of exposed individuals and their offspring

  20. Effect of organosolv and soda pulping processes on the metals content of non-woody pulps.

    Science.gov (United States)

    González, M; Cantón, L; Rodríguez, A; Labidi, J

    2008-09-01

    In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).

  1. Pulp regeneration: Current approaches and future challenges

    Directory of Open Access Journals (Sweden)

    Jingwen eYANG

    2016-03-01

    Full Text Available Regenerative endodontics aims to replace inflamed/necrotic pulp tissues with regenerated pulp-like tissues to revitalize teeth and improve life quality. Pulp revascularization case reports, which showed successful clinical and radiographic outcomes, indicated the possible clinical application of pulp regeneration via cell homing strategy. From a clinical point of view, functional pulp-like tissues should be regenerated with the characterization of vascularization, re-innervation, and dentin deposition with a regulated rate similar to that of normal pulp. Efficient root canal disinfection and proper size of the apical foramen are the two requisite preconditions for pulp regeneration. Progress has been made on pulp regeneration via cell homing strategies. This review focused on the requisite preconditions and cell homing strategies for pulp regeneration. In addition to the traditionally used mechanical preparation and irrigation, antibiotics, irrigation assisted with EndoVac apical negative-pressure system, and ultrasonic and laser irradiation are now being used in root canal disinfection. In addition, pulp-like tissues could be formed with the apical foramen less than 1 mm, although more studies are needed to determine the appropriate size. Moreover, signaling molecules including stromal cell derived factor (SDF-1α, basic Fibroblast Growth Factor (bFGF, Platelet Derived Growth Factor (PDGF, stem cell factor (SCF, and Granulocyte Colony-Stimulating Factor (G-CSF were used to achieve pulp-like tissue formation via a cell homing strategy. Studies on the cell sources of pulp regeneration might give some indications on the signaling molecular selection. The active recruitment of endogenous cells into root canals to regenerate pulp-like tissues is a novel concept that may offer an unprecedented opportunity for the near-term clinical translation of current biology-based therapies for dental pulp regeneration.

  2. Data storage on Russian pesticide producers exposed to dioxin. Sex ratios of third generation of Russian cohort

    Energy Technology Data Exchange (ETDEWEB)

    Amirova, Z.; Kruglov, E. [Environmental Research and Protection Center, Ufa (Russian Federation); Dardynskaia, I. [Univ. of Illinois, School of Public Health, Chicago (United States)

    2004-09-15

    A cohort of Russian workers who produced 2,4,5-T and 2,4,5-TrCP at a chemical factory in Ufa was brought to light in the papers of A. Schecter, J. Ryan and O. Papke. Dioxin exposure was experimentally confirmed by PCDD/Fs determination in blood samples first for a small group of workers and their children. This study permitted to connect the information of medical institutions about chloracne from which a group of young 2,4,5-T workers suffered in 1965-67 with exposure to dioxin. This report presents the results of the detailed study of the third generation of the Russian cohort (247 workers, 314 children and 260 grandchildren). We also present the data on the sex ratio of the second generation for the initial group enlarged by 25% as compared with the group of workers analyzed by J. Ryan et al. (198 workers and 227 children). Besides, as skewed sex ratio had earlier been stated only for paternal descendants, genealogical branches of the cohort representatives were studied.

  3. Pre-treatment and ethanol fermentation potential of olive pulp at different dry matter concentrations

    DEFF Research Database (Denmark)

    Haagensen, Frank Drøscher; Skiadas, Ioannis V.; Gavala, Hariklia N.

    2009-01-01

    potential of the olive pulp, which is the semi solid residue generated from the two-phase processing of the olives for olive oil production. Wet oxidation and enzymatic hydrolysis have been applied aiming at the enhancement of carbohydrates' bioavailability. Different concentrations of enzymes and enzymatic......, implying that wet oxidation is not a recommended pre-treatment process for olive pulp at the conditions tested. It was also showed that increased dry matter concentration did not have a negative effect on the release of sugars, indicating that the cellulose and xylan content of the olive pulp is relatively...

  4. Purified Human Dental Pulp Stem Cells Promote Osteogenic Regeneration.

    Science.gov (United States)

    Yasui, T; Mabuchi, Y; Toriumi, H; Ebine, T; Niibe, K; Houlihan, D D; Morikawa, S; Onizawa, K; Kawana, H; Akazawa, C; Suzuki, N; Nakagawa, T; Okano, H; Matsuzaki, Y

    2016-02-01

    Human dental pulp stem/progenitor cells (hDPSCs) are attractive candidates for regenerative therapy because they can be easily expanded to generate colony-forming unit-fibroblasts (CFU-Fs) on plastic and the large cell numbers required for transplantation. However, isolation based on adherence to plastic inevitably changes the surface marker expression and biological properties of the cells. Consequently, little is currently known about the original phenotypes of tissue precursor cells that give rise to plastic-adherent CFU-Fs. To better understand the in vivo functions and translational therapeutic potential of hDPSCs and other stem cells, selective cell markers must be identified in the progenitor cells. Here, we identified a dental pulp tissue-specific cell population based on the expression profiles of 2 cell-surface markers LNGFR (CD271) and THY-1 (CD90). Prospectively isolated, dental pulp-derived LNGFR(Low+)THY-1(High+) cells represent a highly enriched population of clonogenic cells--notably, the isolated cells exhibited long-term proliferation and multilineage differentiation potential in vitro. The cells also expressed known mesenchymal cell markers and promoted new bone formation to heal critical-size calvarial defects in vivo. These findings suggest that LNGFR(Low+)THY-1(High+) dental pulp-derived cells provide an excellent source of material for bone regenerative strategies. © International & American Associations for Dental Research 2015.

  5. Drying kinetics of atemoya pulp

    Directory of Open Access Journals (Sweden)

    Plúvia O. Galdino

    Full Text Available ABSTRACT This study was conducted in order to obtain drying curves of whole atemoya pulp through the foam-mat drying method. The suspension was prepared with whole atemoya pulp mixed with 2% of Emustab® and 2% of Super Liga Neutra® with mixing time of 20 min, and dried in a forced-air oven at different temperatures (60; 70 and 80 °C and thicknesses of the foam layer (0.5, 1.0 and 1.5 cm. The drying rate curves were plotted against the water content ratio and the semi-theoretical models of Henderson & Pabis, Page and Midilli were used. All tested models showed coefficient of determination (R2 above 0.993, and the Midilli model showed the best fit for all conditions. Drying curves were affected by temperature and layer thickness.

  6. Assessing the value of pulp mill biomass savings in a climate change conscious economy

    International Nuclear Information System (INIS)

    Adahl, Anders; Harvey, Simon; Berntsson, Thore

    2006-01-01

    Pulp mills use significant amounts of biofuels, both internal and purchased. Biofuels could contribute to reach greenhouse gas emission targets at competitive costs. Implementing process integration measures at a pulp mill in order to achieve pulp production with less use of energy (biofuels) has not only on-site consequences but also off-site consequences, such as substitution of fossil fuels elsewhere by the saved pulp mill biofuels, and less on-site electric power generation. In this paper a method, a linking model, is suggested to analyse pulp mill biofuel saving measures when carbon dioxide (CO 2 ) external costs are internalised. The linking model is based on equilibrium economics and links information from CO 2 constrained energy market future scenarios with process integration measures. Pulp mill economics and marginal energy market CO 2 response are identified. In an applied study, four process integration measures at a Swedish pulp mill were analysed using five energy market future scenarios emanating from a Nordic energy model. The investigated investment alternatives for biofuel savings all result in positive net annual savings, irrespectively of the scenario used. However, CO 2 emissions may increase or decrease depending on the future development of the Nordic energy market

  7. Effects of the bleaching sequence on the optical brighteners action in eucalyptus kraft pulp

    Directory of Open Access Journals (Sweden)

    Mauro Manfredi

    2014-06-01

    Full Text Available During the bleaching process the pulp is treated with chemical reagents that can be retained in the pulp and interfere in the action of the optical brighteners. Different bleaching sequences can produce pulps at the same brightness but with different potential to whiteness increase when treated with optical brighteners. The objective of this study was to evaluate the influence of the bleaching sequence on the efficiency of disulphonated and tetrasulphonated optical brighteners. Eucalyptus kraft pulp was bleached using four different bleaching sequences. For each pulp three brightness targets were aimeds. For each bleaching sequence mathematical model was generated for predicting the final pulp whiteness according to the initial brightness and the optical brightener charge applied. The presence of organochlorine residues in the pulp reduced the effectiveness of the optical brighteners. Therefore, bleaching sequences that use low chlorine dioxide charge favors for greater gains in whiteness with the application of optical brighteners. The replacement of the final chlorine dioxide bleaching stage with a hydrogen peroxide one in the sequence increased the efficiency of the optical brightening agents.

  8. [Daily practice and pulp diseases].

    Science.gov (United States)

    Calmein, S; Claisse, A

    1990-09-01

    Constructive or destructive processes of pulp tissue depend on many factors: anatomic topography, particular physiology, or intensity and duration of infectious, mechanical and chemical aggression. Also irritation of the pulpo-dentinal complex induce histologic and physiologic changes. The positive diagnosis of hyperemia, acute or chronic pulpitis, pulpal necrosis and acute or chronic apical abscess is performed by clinical investigations which allow a differential diagnosis with other dental or extra-dental diseases. These multiple steps lead to an adapted and appropriate treatment.

  9. A new method to extract dental pulp DNA: application to universal detection of bacteria.

    Directory of Open Access Journals (Sweden)

    Lam Tran-Hung

    Full Text Available BACKGROUND: Dental pulp is used for PCR-based detection of DNA derived from host and bacteremic microorganims. Current protocols require odontology expertise for proper recovery of the dental pulp. Dental pulp specimen exposed to laboratory environment yields contaminants detected using universal 16S rDNA-based detection of bacteria. METHODOLOGY/PRINCIPAL FINDINGS: We developed a new protocol by encasing decontaminated tooth into sterile resin, extracting DNA into the dental pulp chamber itself and decontaminating PCR reagents by filtration and double restriction enzyme digestion. Application to 16S rDNA-based detection of bacteria in 144 teeth collected in 86 healthy people yielded a unique sequence in only 14 teeth (9.7% from 12 individuals (14%. Each individual yielded a unique 16S rDNA sequence in 1-2 teeth per individual. Negative controls remained negative. Bacterial identifications were all confirmed by amplification and sequencing of specific rpoB sequence. CONCLUSIONS/SIGNIFICANCE: The new protocol prevented laboratory contamination of the dental pulp. It allowed the detection of bacteria responsible for dental pulp colonization from blood and periodontal tissue. Only 10% such samples contained 16S rDNA. It provides a new tool for the retrospective diagnostic of bacteremia by allowing the universal detection of bacterial DNA in animal and human, contemporary or ancient tooth. It could be further applied to identification of host DNA in forensic medicine and anthropology.

  10. Properties of cellulose derivatives produced from radiation-Modified cellulose pulps

    International Nuclear Information System (INIS)

    Iller, Edward; Stupinska, Halina; Starostka, Pawel

    2007-01-01

    The aim of project was elaboration of radiation methods for properties modification of cellulose pulps using for derivatives production. The selected cellulose pulps were exposed to an electron beam with energy 10 MeV in a linear accelerator. After irradiation pulps underwent the structural and physico-chemical investigations. The laboratory test for manufacturing carboxymethylocellulose (CMC), cellulose carbamate (CC) and cellulose acetate (CA) with cellulose pulps irradiated dose 10 and 15 kGy have been performed. Irradiation of the pulp influenced its depolimerisation degree and resulted in the drop of viscosity of CMC. However, the expected level of cellulose activation expressed as a rise of the substitution degree or increase of the active substance content in the CMC sodium salt was not observed. In the case of cellulose esters (CC, CA) formation, the action of ionising radiation on cellulose pulps with the dose 10 and 15 kGy enables obtaiment of the average values of polimerisation degree as required for CC soluble in aqueous sodium hydroxide solution. The properties of derivatives prepared by means of radiation and classic methods were compared

  11. EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

    OpenAIRE

    Ahmad Azizi Mossello; Jalaluddin Harun; Rushdan Ibrahim; Hossien Resalati; Seyed Rashid Fallah Shamsi; Paridah Md Tahir; Mohd Nor Mohad Yusoff

    2010-01-01

    Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ) pulp of kenaf fibers versus old corrugated container (OCC) and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the h...

  12. Absent in melanoma 2 (AIM2) in rat dental pulp mediates the inflammatory response during pulpitis.

    Science.gov (United States)

    Wang, Yafei; Zhai, Shafei; Wang, Haijing; Jia, Qian; Jiang, Wenkai; Zhang, Xiao; Zhang, Ansheng; Liu, Jun; Ni, Longxing

    2013-11-01

    In recent years, the inflammasome has been determined to play an important role in inflammatory diseases. However, the role of the inflammasome in pulpitis remains unclear. Absent in melanoma 2 (AIM2) is a type of inflammasome that recognizes cytosolic double stranded DNA and forms a caspase-1-activating inflammasome with apoptosis-associated speck-like protein containing a caspase activating recruiting domain. In this study, we determined whether AIM2 was expressed in pulp cells and defined the role of AIM2 in the initiation of inflammation within the dental pulp. In the in vivo study, the right maxillary molars from male adult Sprague-Dawley rats (250-350 g) were exposed to the pulp. In the in vitro study, the pulp cells isolated from the mandibular incisors of the Sprague-Dawley rats (2 weeks) were conventionally cultured. Immunofluorescence staining was used to determine the expression and distribution of AIM2 in the rat dental pulp tissues and cells in the presence or absence of inflammatory stimulation. Western blotting and real-time polymerase chain reaction were performed to determine whether there was a correlation between AIM2 expression levels and inflammation both in vivo and in vitro. In healthy dental pulp tissues and cells, AIM2 was only detected in the odontoblast layer. Stimulation significantly increased AIM2 expression in both the dental pulp tissues and cultured cells. The mRNA and protein levels of AIM2 were significantly up-regulated in response to inflammatory stimulation in a dose-dependent manner. Moreover, we also found that AIM2 expression correlated with interleukin-1 levels. These results reveal a direct relationship between the AIM2 inflammasome and pulpitis. Our study demonstrates that AIM2 is expressed in dental pulp tissues and mediates the inflammatory response during pulpitis. Therapeutic interventions aimed at reducing AIM2 expression may be beneficial in the treatment of pulpitis. Copyright © 2013 American Association of

  13. Diabetes induces metabolic alterations in dental pulp.

    Science.gov (United States)

    Leite, Mariana Ferreira; Ganzerla, Emily; Marques, Márcia Martins; Nicolau, José

    2008-10-01

    Diabetes can interfere in tissue nutrition and can impair dental pulp metabolism. This disease causes oxidative stress in cells and tissues. However, little is known about the antioxidant system in the dental pulp of diabetics. Thus, it would be of importance to study this system in this tissue in order to verify possible alterations indicative of oxidative stress. The aim of this study was to evaluate some parameters of antioxidant system of the dental pulp of healthy (n = 8) and diabetic rats (n = 8). Diabetes was induced by streptozotocin in rats. Six weeks after diabetes induction, a pool of the dental pulp of the 4 incisors of each rat (healthy and diabetic) was used for the determination of total protein and sialic acid concentrations and catalase and peroxidase activities. Data were compared by a Student t test (p pulps from both groups presented similar total protein concentrations and peroxidase activity. Dental pulps of diabetic rats exhibited significantly lower free, conjugated, and total sialic acid concentrations than those of control tissues. Catalase activity in diabetic dental pulps was significantly enhanced in comparison with that of control pulps. The result of the present study is indicative of oxidative stress in the dental pulp caused by diabetes. The increase of catalase activity and the reduction of sialic acid could be resultant of reactive oxygen species production.

  14. PRODUCTION OF DISSOLVING GRADE PULP FROM ALFA

    Directory of Open Access Journals (Sweden)

    Baya Bouiri

    2010-02-01

    Full Text Available Alfa, also known as Stipa tenacissimaI or “halfa”, is grown in North Africa and south Spain. Due to its short fiber length, paper made from alfa pulp retains bulk and takes block letters well. In this study alfa was evaluated for bleached pulp production. Two cellulose pulps with different chemical compositions were pulped by a conventional kraft process. One sample was taken from the original alfa material and another from alfa that had been pretreated by diluted acid. The pulp produced from the pretreated alfa was bleached by the elemental-chlorine-free sequences DEPD and DEDP. The yield, Kappa number, brightness, and α- cellulose content of bleached and unbleached pulps were evaluated. The results showed that during the chemical pulping process, treated alfa cooked more easily than the original alfa. The treated alfa pulp also showed very good bleaching, reaching a brightness level of 94.8% ISO with a yield of 93.6% at an α-cellulose content 96.8(% with a DEDP bleaching sequence, compared to 83.2% ISO brightness level, 92.8% yield, and 95.1% α-cellulose content for bleached pulp with a DEPD bleaching sequence. Therefore, this alfa material could be considered as a worthwhile choice for cellulosic fiber supply.

  15. Eucalyptus kraft pulp production: Thermogravimetry monitoring

    International Nuclear Information System (INIS)

    Barneto, Agustin G.; Vila, Carlos; Ariza, Jose

    2011-01-01

    Highlights: → Thermogravimetric analysis can be used to monitor the pulping process in a pulp mill. → ECF bleaching process affects the crystalline cellulose volatilization. → The fibre size has an influence on composition and thermal behavior of pulp. - Abstract: Under oxidative environment the thermal degradation of lignocellulosic materials like wood or pulp is sensitive to slight composition changes. For this, in order to complement the chemical and X-ray diffraction results, thermogravimetric analyses (TGA) were used to monitor pulp production in a modern pulp mill. Runs were carried out on crude, oxygen delignified and bleached pulps from three eucalyptus woods from different species and geographical origins. Moreover, with the modeling of thermogravimetric data, it was possible to obtain an approximate composition of samples which includes crystalline and amorphous cellulose. TGA results show that pulping has an intensive effect on bulk lignin and hemicellulose, but it has limited influence on the removal of these substances when they are linked to cellulose microfibril. The stages of oxygen delignification and bleaching, based in chlorine dioxide and hydrogen peroxide, increase the crystalline cellulose volatilization rate. These changes are compatible with a more crystalline microfibril. The influence of the fibre size on pulp composition, crystallinity and thermal degradation behavior was observed.

  16. Organo mercurials in pulp and paper industry

    Energy Technology Data Exchange (ETDEWEB)

    Bouveng, H O

    1967-01-01

    Today phenyl mercury acetate (PMA) is used in the paper and pulp industry for two purposes: slime control in paper machine systems and impregnation of wet mechanical pulp. PMA is a commonly used slimicide. It is used for slime control in such a way that a minor part (5-20% depending on mill operation) will reach the watercourse with the waste water and contaminate aquatic life. PMA used for impregnation concerns wet mechanical pulp produced for export as raw material, mostly for newsprint. Treatment of this pulp with PMA is necessary to avoid changes caused by molds and rot fungi.

  17. Pulp and paper production from Spruce wood with kraft and ...

    African Journals Online (AJOL)

    STORAGESEVER

    2010-03-15

    Mar 15, 2010 ... optical properties of resultant paper were included to determine the properties of these pulp samples. ... pulping compounds in the kraft method are Na2S and .... Scanning electron microscope (SEM) measurement of pulp.

  18. Dental pulp stone formation during orthodontic treatment: A ...

    African Journals Online (AJOL)

    2015-06-21

    Jun 21, 2015 ... the presence of dental pulp stone, gender, age, tooth type and arches. Results: Dental pulp ... primary and permanent dentition.[1] Dental pulp stones .... interpretation provided training to familiarize the other observer with the ...

  19. Catalase activity in healthy and inflamed pulp tissues of permanent ...

    African Journals Online (AJOL)

    2015-11-02

    Nov 2, 2015 ... pulps, which is due to pulpitis in comparison to healthy dental pulp. Key words: .... human dental pulp cells by Porphyromonas endodontalis lipopolysaccharide. J Endod ... Biology of disease: Free radicals and tissue injury.

  20. Energy conservation in the pulp and paper industry. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-05-01

    Almost 40 specific research and development ideas were formulated by the 67 participants at this workshop. Projects were assessed with the following criteria in mind: potential energy savings, cost, risk, Federal role, time frame, and priority. Data are tabulated on the projects followed by six topics discussed by panel members: waste and recycling, energy management in the mill, papermaking, pulping and bleaching, power generation in the mill, and coating and conversion. Three summary speeches are included. (MCW)

  1. Alternative Technologies for Biofuels Production in Kraft Pulp Mills—Potential and Prospects

    Directory of Open Access Journals (Sweden)

    Esa Vakkilainen

    2012-07-01

    Full Text Available The current global conditions provide the pulp mill new opportunities beyond the traditional production of cellulose. Due to stricter environmental regulations, volatility of oil price, energy policies and also the global competitiveness, the challenges for the pulp industry are many. They range from replacing fossil fuels with renewable energy sources to the export of biofuels, chemicals and biomaterials through the implementation of biorefineries. In spite of the enhanced maturity of various bio and thermo-chemical conversion processes, the economic viability becomes an impediment when considering the effective implementation on an industrial scale. In the case of kraft pulp mills, favorable conditions for biofuels production can be created due to the availability of wood residues and generation of black liquor. The objective of this article is to give an overview of the technologies related to the production of alternative biofuels in the kraft pulp mills and discuss their potential and prospects in the present and future scenario.

  2. In vitro penetration of bleaching agents into the pulp chamber

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Valera, M C; Mancini, M N G

    2004-01-01

    To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures.......To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures....

  3. Modeling the kinetics nonenzymatic browning reactions and rheological behavior in the termal process of fruit juices and pulps

    Directory of Open Access Journals (Sweden)

    Damian Manayay

    2010-06-01

    Full Text Available In the manufacture of fruit juices and pulps, is of paramount importance to refer to non-enzymatic browning and rheological behavior. The non-enzymatic browning is a phenomenon of darkening of a purely chemical (Braverman, 1980, is characterized by the presence of brown polymers called melanoidins, generated by the Maillard reaction or condensation of melanoidins, the caramelization and degradation of acid ascorbic, while the rheological behavior is define as the proportion deformation of the material when exposed to shear stress (σ caused by a rheometer (Muller, 1978; Ibarz, 2005. Modeling studies of colour formation and definition of rheological behavior, considered in this review, aimed at the conclusion of the existence of a zero kinetic and first order respectively, and the most influential factors with the reactions are mainly Maillard, temperature, amino acids presence, water activity and pH, while the rheological behavior is affected by temperature, solid concentration and particles size that make up the suspension in the specific case of the pulps.

  4. Histological transformations of the dental pulp as possible indicator of post mortem interval: a pilot study.

    Science.gov (United States)

    Carrasco, Patricio A; Brizuela, Claudia I; Rodriguez, Ismael A; Muñoz, Samuel; Godoy, Marianela E; Inostroza, Carolina

    2017-10-01

    The correct estimation of the post mortem interval (PMI) can be crucial on the success of a forensic investigation. Diverse methods have been used to estimate PMI, considering physical changes that occur after death, such as mortis algor, livor mortis, among others. Degradation after death of dental pulp is a complex process that has not yet been studied thoroughly. It has been described that pulp RNA degradation could be an indicator of PMI, however this study is limited to 6 days. The tooth is the hardest organ of the human body, and within is confined dental pulp. The pulp morphology is defined as a lax conjunctive tissue with great sensory innervation, abundant microcirculation and great presence of groups of cell types. The aim of this study is to describe the potential use of pulp post mortem alterations to estimate PMI, using a new methodology that will allow obtainment of pulp tissue to be used for histomorphological analysis. The current study will identify potential histological indicators in dental pulp tissue to estimate PMI in time intervals of 24h, 1 month, 3 months and 6 months. This study used 26 teeth from individuals with known PMI of 24h, 1 month, 3 months or 6 months. All samples were manipulated with the new methodology (Carrasco, P. and Inostroza C. inventors; Universidad de los Andes, assignee. Forensic identification, post mortem interval estimation and cause of death determination by recovery of dental tissue. United State patent US 61/826,558 23.05.2013) to extract pulp tissue without the destruction of the tooth. The dental pulp tissues obtained were fixed in formalin for the subsequent generation of histological sections, stained with Hematoxylin Eosin and Masson's Trichrome. All sections were observed under an optical microscope using magnifications of 10× and 40×. The microscopic analysis of the samples showed a progressive transformation of the cellular components and fibers of dental pulp along PMI. These results allowed creating a

  5. Steam System Opportunity Assessment for the Pulp and Paper, Chemical Manufacturing, and Petroleum Refining Industries: Main Report

    Energy Technology Data Exchange (ETDEWEB)

    2002-10-01

    This report assesses steam generation and use in the pulp and paper, chemical, and petroleum refining industries, and estimates the potential for energy savings from implementation of steam system performance and efficiency improvements.

  6. Steam system opportunity assessment for the pulp and paper, chemical manufacturing, and petroleum refining industries: Main report

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2002-10-01

    This report assesses steam generation and use in the pulp and paper, chemical, and petroleum refining industries, and estimates the potential for energy savings from implementation of steam system performance and efficiency improvements.

  7. PULP DEMAND IN THE INTERNATIONAL MARKET

    Directory of Open Access Journals (Sweden)

    Edmilson Santos Cruz

    2003-01-01

    Full Text Available This study aimed at analyzing the international pulp market, taking into account themain exporting countries and importing regions, with the objective of estimating, for each market, theown-price and cross-price elasticity in relation to the demand of the pulp, differentiated for country oforigin. The model considers that imports are differentiated by origin; therefore they are not perfect substitutes. The demand from Europe, North America and the Rest of the World for the pulp from theUnited States,Canada, Sweden, Finland, Portugal and Brazil was inelastic. The Asian demand for thissome pulp was elastic. Europe and the Rest of the World showed negative cross-price elasticity, i. e.,and the imported pulp from other countries are complementary products. North America and Asiashowed positive crow-price elasticity, i. e., they consider the pulp produced in other countries assubstitute products. The net effect of the variation on the price of pulp in a country h, over the amountof pulp that goes to the region i depends on the matching of values related to the elasticity ofsubstitution and the price elasticity of the total demand.

  8. Characterization of sugar beet pulp derived oligosaccharides

    NARCIS (Netherlands)

    Leijdekkers, M.

    2015-01-01

    Abstract

    This thesis aimed at characterizing complex mixtures of sugar beet pulp derived oligosaccharides, in order to be able to monitor and optimize the enzymatic saccharification of sugar beet pulp.

    Hydrophilic interaction chromatography with on-line evaporative

  9. Pulp quality from small-diameter trees.

    Science.gov (United States)

    G.C. Myers; S. Kumar; R.R. Gustafson; R.J. Barbour; S.M. Abubakr

    1997-01-01

    Kraft and thermomechanical (TMP) pulps were prepared and evaluated from lodgepole pine and mixed Douglas-fir/western larch sawmill residue chips; lodgepole pine, Douglas-fir, and western larch submerchantable logs; and lodgepole pine, Douglas-fir, and western larch small trees and tops. Kraft pulp from small trees and tops was identical to that from submerchantable...

  10. Enzymes improve ECF bleaching of pulp

    Directory of Open Access Journals (Sweden)

    Lachenal, D.

    2006-07-01

    Full Text Available The delignification efficiency of different laccase enzymes was examined on the eucalyptus Kraft pulp. The laccase enzyme from Trametes versicolor showing the highest delignification efficiency was selected and used in the elemental chlorine-free bleaching sequence for improving the pulp bleachability. An appreciable reduction in chlorine dioxide consumption was also obtained. Further reduction in chlorine dioxide consumption was obtained when the same laccase treated pulp was subjected to an acid treatment after the extraction stage followed by the DEPD sequence. Elemental-chlorine free bleaching was also performed using the xylanase-laccase treated pulp. Xylanase treatment was incorporated to the laccase mediator system in the elemental-chlorine free bleaching both sequentially and simultaneously. The bleaching sequence DEPD followed and in both the cases, the reduction in chlorine dioxide consumption was greater in comparison to the control. The chlorine dioxide consumption was reduced further when xylanase-laccase treated pulp was given an additional acid treatment. The final pulp properties of the treated pulps were comparable to the control pulp.

  11. Energy conservation in pulp and paper industry: some thoughts

    Energy Technology Data Exchange (ETDEWEB)

    Sadawarte, N. S.; Prasad, A. K.; Khanolkar, V. D.; Shenoy, S. C.

    1980-03-15

    The pulp and paper industry is highly energy intensive. In view of the spiralling fuel prices and rising power costs, there is an urgent need to conserve energy through better management of various operations in the industry, from the optimal utilization of the forest residues to the shipment of the final product. The total energy concept, e.g., energy generation, distribution and utilization in Indian paper industry is discussed. The need for an energy audit is emphasized and the formats of energy reporting forms are included. Short and long term measures to be enforced to achieve energy savings in the pulp and paper mills are outlined. Some important energy conservation approaches are also discussed. Factors affecting energy efficiency in a pulp and paper mill are reviewed. Some areas where sustained R and D efforts should be focused to make the paper industry nearly self-sufficient in energy generation and utilization are also given. It is essential to have a National Energy Policy clearly defining achievable targets of energy conservation for industry. The Indian paper industry could advantageously form its own committee to review the operation of the various mills in the country and come out with concrete solutions for higher energy efficiency and more effective conservation of energy.

  12. Perspectives for Cell-homing Approaches to Engineer Dental Pulp.

    Science.gov (United States)

    Galler, Kerstin M; Widbiller, Matthias

    2017-09-01

    Sufficient proof is available today to demonstrate that dental pulp tissue engineering is possible. The body of evidence was generated mainly on cell transplantation; however, because of several severe problems afflicted with this approach, it might not be feasible for a clinical setting in the near future. More recently, cell homing has been proposed as a viable alternative. We suggest a modification of the tissue engineering paradigm, where resident cells are attracted by endogenous, dentin-derived growth factors that further induce cell proliferation and differentiation and a bioactive scaffold material laden with these growth factors that serves as a template for tissue formation. This article highlights the latest developments regarding scaffold materials, stem cells, and dentin-derived growth factors specifically for a cell-homing approach to engineer dental pulp and summarizes new ideas. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  13. Trans-generational study of DNA alterations and their consequences on life history traits and energy budget of Daphnia magna exposed to depleted uranium

    International Nuclear Information System (INIS)

    Plaire, Delphine

    2013-01-01

    Understanding how toxicants affect species at various levels of biological organization is a major research goal in both ecotoxicology and radioecology. As part of IRSN program ENVIRHOM, which aims to assess environmental risks related to the presence of radionuclides in the environment, this PhD work explored how depleted uranium alters DNA and affects life history traits (survival, growth and reproduction) of an aquatic invertebrate, Daphnia magna. To answer to this problematic, an experimental approach and a modeling approach are conducted. An experimental study is performed to evaluate DNA accumulation and transmission during an uranium exposure (0; 2; 9.9; 22.2 and 50 μg.L -1 ) over two successive generations (F0 and F1). Different exposures scenarios (continuous, post-hatching and embryo exposure) are achieved to test the specific sensitivity of several life stages to uranium. Genotoxic effects are estimated using random amplified DNA technique combined with PCR (PCR-RAPD). In continuous and post-hatching exposure scenarios, results highlighted an accumulation and a transmission of DNA damage across generations with an increase in effect severity. DNA alterations are reported at hatching of the F1 generation at a concentration as low as 2 μg.L -1 . Effects on growth and reproduction are stronger when the embryo stage is exposed and remain visible at 9.9 μg.L -1 despite a return in a clean medium at hatching. Results suggest that DNA damage could be used as early indicators of future effects on life history traits. A mechanistic analysis of experimental results is conducted using a DEBtox model (dynamic energy budget applied to toxicology) to better understand the causes of the increase in effect severity across generations. A model with two stress factors (one correlated to external concentration and another correlated to a damage level) is developed. Results of fits suggest the involvement of one second mode of action to explain immediate effects of

  14. Reactions of human dental pulp cells to capping agents in the presence or absence of bacterial exposure.

    Science.gov (United States)

    Cai, Shiwei; Zhang, Wenjian; Tribble, Gena; Chen, Wei

    2017-01-01

    An ideal pulp-capping agent needs to have good biocompatibility and promote reparative dentinogenesis. Although the effects of capping agents on healthy pulp are known, limited data regarding their effects on bacterial contaminated pulp are available. This study aimed to evaluate the reaction of contaminated pulps to various capping agents to assist clinicians in making informed decisions. Human dental pulp (HDP) cell cultures were developed from extracted human molars. The cells were exposed to a bacterial cocktail comprising Porphyromonas gingivalis, Prevotella intermedia, and Streptococcus gordonii before being cocultured with capping agents such as mineral trioxide aggregate (MTA) Portland cement (PC), and Dycal. HDP cell proliferation was assayed by MTS colorimetric cell proliferation assay, and its differentiation was evaluated by real-time PCR for detecting alkaline phosphatase, dentin sialophosphoprotein, and osteocalcin expressions. MTA and PC had no apparent effect, whereas Dycal inhibited HDP cell proliferation. PC stimulated HDP cell differentiation, particularly when they were exposed to bacteria. MTA and Dycal inhibited differentiation, regardless of bacterial infection. In conclusion, PC was the most favorable agent, followed by MTA, and Dycal was the least favorable agent for supporting the functions of bacterial compromised pulp cells.

  15. Biomimetic extracellular matrix mediated somatic stem cell differentiation: applications in dental pulp tissue regeneration

    Science.gov (United States)

    Ravindran, Sriram; George, Anne

    2015-01-01

    Dental caries is one of the most widely prevalent infectious diseases in the world. It affects more than half of the world's population. The current treatment for necrotic dental pulp tissue arising from dental caries is root canal therapy. This treatment results in loss of tooth sensitivity and vitality making it prone for secondary infections. Over the past decade, several tissue-engineering approaches have attempted regeneration of the dental pulp tissue. Although several studies have highlighted the potential of dental stem cells, none have transitioned into a clinical setting owing to limited availability of dental stem cells and the need for growth factor delivery systems. Our strategy is to utilize the intact ECM of pulp cells to drive lineage specific differentiation of bone marrow derived mesenchymal stem cells. From a clinical perspective, pulp ECM scaffolds can be generated using cell lines and patient specific somatic stem cells can be used for regeneration. Our published results have shown the feasibility of using pulp ECM scaffolds for odontogenic differentiation of non-dental mesenchymal cells. This focused review discusses the issues surrounding dental pulp tissue regeneration and the potential of our strategy to overcome these issues. PMID:25954205

  16. Characterization of Human Dental Pulp Tissue Under Oscillatory Shear and Compression.

    Science.gov (United States)

    Ozcan, Burak; Bayrak, Ece; Erisken, Cevat

    2016-06-01

    Availability of material as well as biological properties of native tissues is critical for biomaterial design and synthesis for regenerative engineering. Until recently, selection of biomaterials and biomolecule carriers for dental pulp regeneration has been done randomly or based on experience mainly due to the absence of benchmark data for dental pulp tissue. This study, for the first time, characterizes the linear viscoelastic material functions and compressive properties of human dental pulp tissue harvested from wisdom teeth, under oscillatory shear and compression. The results revealed a gel-like behavior of the pulp tissue over the frequency range of 0.1-100 rps. Uniaxial compression tests generated peak normal stress and compressive modulus values of 39.1 ± 20.4 kPa and 5.5 ± 2.8 kPa, respectively. Taken collectively, the linear viscoelastic and uniaxial compressive properties of the human dental pulp tissue reported here should enable the better tailoring of biomaterials or biomolecule carriers to be employed in dental pulp regeneration.

  17. Mineral Trioxide Aggregate and Portland Cement for Direct Pulp Capping in Dog: A Histopathological Evaluation

    Directory of Open Access Journals (Sweden)

    Maryam Bidar

    2014-09-01

    Full Text Available Background and aims. Mineral trioxide aggregate and calcium hydroxide are considered the gold standard pulp-capping materials. Recently, Portland cement has been introduced with properties similar to those of mineral trioxide aggregate. His-topathological effects of direct pulp capping using mineral trioxide aggregate and Portland cements on dog dental pulp tis-sue were evaluated in the present study. Materials and methods. This histopatological study was carried out on 64 dog premolars. First, the pulp was exposedwith a sterile bur. Then, the exposed pulp was capped with white or gray mineral trioxide aggregates and white or gray Port-land cements in each quadrant and sealed with glass-ionomer. The specimens were evaluated under a light microscope after 6 months. Statistical analysis was carried out using Kruskal-Wallis test. Statistical significance was defined at α=5%. Results. There was no acute inflammation in any of the specimens. Chronic inflammation in white and gray mineral triox-ide aggregates and white and gray Portland cements was reported to be 45.5%, 27.3%, 57.1% and 34.1%, respectively. Al-though the differences were not statistically significant, severe inflammation was observed mostly adjacent to white mineral trioxide aggregate. The largest extent of increased vascularization (45% and the least increase in fibrous tissue were ob-served adjacent to white mineral trioxide aggregate, with no significant differences. In addition, the least calcified tissue formed adjacent to white mineral trioxide aggregate, although the difference was not significant. Conclusion. The materials used in this study were equally effective as pulp protection materials following direct pulp cap-ping in dog teeth.

  18. Pulping Variables, Storage Time and Pitch Deposit | Ogunwusi ...

    African Journals Online (AJOL)

    Pulp resin is also influenced by effective alkali concentration of the pulping medium. With increase in effective alkali concentration from 13% to 15%, pulp pitch is reduced. The interaction effect of storage and effective alkali concentration was not significant indicating that reduction in pulp pitch caused by effective alkali ...

  19. Pulp mill as an energy producer

    International Nuclear Information System (INIS)

    Kaulamo, O.

    1998-01-01

    The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

  20. High-yield pulping effluent treatment technologies

    International Nuclear Information System (INIS)

    Su, W.X.; Hsieh, J.S.

    1993-03-01

    The objective of this report is to examine the high-yield (mechanical) pulp processes with respect to environmental issues affected by the discharge of their waste streams. Various statistics are given that support the view that high-yield pulping processes will have major growth in the US regions where pulp mills are located, and sites for projects in the development phase are indicated. Conventional and innovative effluent-treatment technologies applicable to these processes are reviewed. The different types of mechanical pulping or high-yield processes are explained, and the chemical additives are discussed. The important relationship between pulp yield and measure of BOD in the effluent is graphically presented. Effluent contaminants are identified, along with other important characteristics of the streams. Current and proposed environmental limitations specifically related to mechanical pulp production are reviewed. Conventional and innovative effluent-treatment technologies are discussed, along with their principle applications, uses, advantages, and disadvantages. Sludge management and disposal techniques become an intimate part of the treatment of waste streams. The conclusion is made that conventional technologies can successfully treat effluent streams under current waste-water discharge limitations, but these systems may not be adequate when stricter standards are imposed. At present, the most important issue in the treatment of pulp-mill waste is the management and disposal of the resultant sludge

  1. Recruitment of dental pulp cells by dentine and pulp extracellular matrix components.

    Science.gov (United States)

    Smith, J G; Smith, A J; Shelton, R M; Cooper, P R

    2012-11-01

    The present study aimed to determine whether dentine tissue and preparations of extracellular matrix (ECM) from pulp (pECM) and dentine (dECM), and breakdown products, influenced pulp cell migration. Chemotaxis transwell and agarose spot assays demonstrated that both dentine and pulp ECM molecules acted as chemoattractants for primary pulp cells. Chemoattractant activities of dECM and pECM were enhanced when subjected to acid and enzymatic breakdown, respectively. This enhanced activity following physiologically relevant breakdown may be pertinent to the disease environment. Pulp cell migration in response to dental ECMs was dependent on an active rho pathway. Recruited cells exhibited increased stem cell marker expression indicating that dental ECMs and their breakdown products selectively attract progenitor cells that contribute to repair processes. In conclusion, combined these results indicate that ECM molecules contribute to cell recruitment necessary for regeneration of the dentine-pulp complex after injury. Copyright © 2012 Elsevier Inc. All rights reserved.

  2. Vital Pulp Therapy—Current Progress of Dental Pulp Regeneration and Revascularization

    Directory of Open Access Journals (Sweden)

    Weibo Zhang

    2010-01-01

    Full Text Available Pulp vitality is extremely important for the tooth viability, since it provides nutrition and acts as biosensor to detect pathogenic stimuli. In the dental clinic, most dental pulp infections are irreversible due to its anatomical position and organization. It is difficult for the body to eliminate the infection, which subsequently persists and worsens. The widely used strategy currently in the clinic is to partly or fully remove the contaminated pulp tissue, and fill and seal the void space with synthetic material. Over time, the pulpless tooth, now lacking proper blood supply and nervous system, becomes more vulnerable to injury. Recently, potential for successful pulp regeneration and revascularization therapies is increasing due to accumulated knowledge of stem cells, especially dental pulp stem cells. This paper will review current progress and feasible strategies for dental pulp regeneration and revascularization.

  3. Optimization of pulping conditions of abaca. An alternative raw material for producing cellulose pulp.

    Science.gov (United States)

    Jiménez, L; Ramos, E; Rodríguez, A; De la Torre, M J; Ferrer, J L

    2005-06-01

    The influence of temperature (150-170 degrees C), pulping time (15-45 min) and soda concentration (5-10%) in the pulping of abaca on the yield, kappa, viscosity, breaking length, stretch and tear index of pulp and paper sheets, was studied. Using a factorial design to identify the optimum operating conditions, equations relating the dependent variables to the operational variables of the pulping process were derived that reproduced the former with errors lower than 25%. Using a high temperature, and a medium time and soda concentration, led to pulp that was difficult to bleach (kappa 28.34) but provided acceptable strength-related properties (breaking length 4728 m; stretch 4.76%; tear index 18.25 mN m2/g), with good yield (77.33%) and potential savings on capital equipment costs. Obtaining pulp amenable to bleaching would entail using more drastic conditions than those employed in this work.

  4. Electrothermal debracketing: patient acceptance and effects on the dental pulp.

    Science.gov (United States)

    Dovgan, J S; Walton, R E; Bishara, S E

    1995-09-01

    Adhesives bond ceramic brackets so effectively that their removal by mechanical forces can fracture the brackets and may damage the tooth surface. Electrothermal debracketers have been developed to facilitate removal; whether the heat generated will damage the underlying pulp is unclear. In our experiment, a prototype device with a high heat tip was used to remove brackets from premolars in patients. The following parameters were evaluated: (1) time required for removal, (2) patient acceptance, and (3) histologic effect on the pulp. Forty-eight experimental teeth planned for orthodontic extraction were bonded by a filled Bis-GMA composite resin and a monocrystalline sapphire bracket. After the chemically cured composite set, debracketing was performed according to the manufacturer's recommendations. Seventeen premolars were not etched or bracketed and served as controls. The interval between heat application and removal of the bracket was timed. Patients were questioned as to sensations during debracketing. Teeth were extracted at 5 to 7 or 28 to 32 days and histologically prepared. Pulps were evaluated for alterations. Brackets were removed in an average of 2.1 seconds, usually at the bracket/composite interface. Patient acceptance was generally positive. Pulpal necrosis was not observed but, in a number of specimens, slight inflammation and odontoblastic disruption occurred at both observation periods.

  5. Physicochemical and functional characteristics of residual pulp of potato

    Directory of Open Access Journals (Sweden)

    Webber Tavares de CARVALHO

    Full Text Available Abstract Starch-rich liquid effluent is generated after peeling, cutting and washing of tubers during the fries processing. After sedimentation of this effluent is recovered a wet residual pulp, and after drying is obtained dry residual pulp or simply named in this study residual pulp of potato (RPP. In order to convert the effluent into a material easy to store for long periods (such as the potato starch, which would make it suitable for various applications. The aim of this study was to evaluate the effect of the drying conditions, specifically variables temperature and air flow on the drying time and water activity, pH, titratable acidity, instrumental colour parameters, water absorption index, water solubility index and oil absorption capacity of dry RPP. Central Composite Design was used, with temperature levels from 50.0 to 70.0 °C and air flow from 0.06 to 0.092 m3 m–2 s–1. Temperature and airflow affected the study characteristics, except for lightness (L*, water solubility index and oil absorption capacity. It was concluded that milder conditions (lower temperatures and intermediate air flow resulted in higher-quality final products (lighter, less acidic, although requiring higher drying time. Therefore, depending on the product application, different drying conditions can be used.

  6. The relationship between pulp calcifications and salivary gland calcifications

    OpenAIRE

    Kaswan, Sumita; Patil, Santosh; Maheshwari, Sneha; Rahman, Farzan; Khandelwal, Suneet

    2014-01-01

    Aim: Pulp stones are discrete calcified bodies found in the dental pulp. Sialolithasis is the most common salivary gland disease. The aim of the present study was to determine the relationship between the pulp stones and salivary gland stones. Material and Methods: 196 patients were randomly selected from the out patient department for the study. The periapical radiographs for all patients were evaluated for the presence or absence of the narrowing of dental pulp chambers and pulp canals. The...

  7. Low Temperature Soda-Oxygen Pulping of Bagasse

    OpenAIRE

    Fengxia Yue; Ke-Li Chen; Fachuang Lu

    2016-01-01

    Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum coo...

  8. 21 CFR 872.1720 - Pulp tester.

    Science.gov (United States)

    2010-04-01

    ... battery powered device intended to evaluate the pulpal vitality of teeth by employing high frequency current transmitted by an electrode to stimulate the nerve tissue in the dental pulp. (b) Classification...

  9. Development of a Direct Pulp-capping Model for the Evaluation of Pulpal Wound Healing and Reparative Dentin Formation in Mice.

    Science.gov (United States)

    Song, Minju; Kim, Sol; Kim, Terresa; Park, Sil; Shin, Ki-Hyuk; Kang, Mo; Park, No-Hee; Kim, Reuben

    2017-01-12

    Dental pulp is a vital organ of a tooth fully protected by enamel and dentin. When the pulp is exposed due to cariogenic or iatrogenic injuries, it is often capped with biocompatible materials in order to expedite pulpal wound healing. The ultimate goal is to regenerate reparative dentin, a physical barrier that functions as a "biological seal" and protects the underlying pulp tissue. Although this direct pulp-capping procedure has long been used in dentistry, the underlying molecular mechanism of pulpal wound healing and reparative dentin formation is still poorly understood. To induce reparative dentin, pulp capping has been performed experimentally in large animals, but less so in mice, presumably due to their small sizes and the ensuing technical difficulties. Here, we present a detailed, step-by-step method of performing a pulp-capping procedure in mice, including the preparation of a Class-I-like cavity, the placement of pulp-capping materials, and the restoration procedure using dental composite. Our pulp-capping mouse model will be instrumental in investigating the fundamental molecular mechanisms of pulpal wound healing in the context of reparative dentin in vivo by enabling the use of transgenic or knockout mice that are widely available in the research community.

  10. A novel role for Twist-1 in pulp homeostasis.

    Science.gov (United States)

    Galler, K M; Yasue, A; Cavender, A C; Bialek, P; Karsenty, G; D'Souza, R N

    2007-10-01

    The molecular mechanisms that maintain the equilibrium of odontoblast progenitor cells in dental pulp are unknown. Here we tested whether homeostasis in dental pulp is modulated by Twist-1, a nuclear protein that partners with Runx2 during osteoblast differentiation. Our analysis of Twist-1(+/-) mice revealed phenotypic changes that involved an earlier onset of dentin matrix formation, increased alkaline phosphatase activity, and pulp stones within the pulp. RT-PCR analyses revealed Twist-1 expression in several adult organs, including pulp. Decreased levels of Twist-1 led to higher levels of type I collagen and Dspp gene expression in perivascular cells associated with the pulp stones. In mice heterozygous for both Twist-1 and Runx2 inactivation, the phenotype of pulp stones appeared completely rescued. These findings suggest that Twist-1 plays a key role in restraining odontoblast differentiation, thus maintaining homeostasis in dental pulp. Furthermore, Twist-1 functions in dental pulp are dependent on its interaction with Runx2.

  11. Low Temperature Soda-Oxygen Pulping of Bagasse.

    Science.gov (United States)

    Yue, Fengxia; Chen, Ke-Li; Lu, Fachuang

    2016-01-13

    Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today's pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm³/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115-125 °C), this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

  12. Low Temperature Soda-Oxygen Pulping of Bagasse

    Directory of Open Access Journals (Sweden)

    Fengxia Yue

    2016-01-01

    Full Text Available Wood shortages, environmental pollution and high energy consumption remain major obstacles hindering the development of today’s pulp and paper industry. Energy-saving and environmental friendly pulping processes are still needed, especially for non-woody materials. In this study, soda-oxygen pulping of bagasse was investigated and a successful soda-oxygen pulping process for bagasse at 100 °C was established. The pulping parameters of choice were under active alkali charge of 23%, maximum cooking temperature 100 °C, time hold at maximum temperature 180 min, initial pressure of oxygen 0.6 MPa, MgSO4 charge 0.5%, and de-pithed bagasse consistency 12%. Properties of the resultant pulp were screened yield 60.9%, Kappa number 14, viscosity 766 dm3/kg, and brightness 63.7% ISO. Similar pulps were also obtained at 110 °C or 105 °C with a cooking time of 90 min. Compared with pulps obtained at higher temperatures (115–125 °C, this pulp had higher screened yield, brightness, and acceptable viscosity, while the delignification degree was moderate. These results indicated that soda-oxygen pulping at 100 °C, the lowest cooking temperature reported so far for soda-oxygen pulping, is a suitable process for making chemical pulp from bagasse. Pulping at lower temperature and using oxygen make it an environmental friendly and energy-saving pulping process.

  13. Effects of the concentration and composition of in-office bleaching gels on hydrogen peroxide penetration into the pulp chamber.

    Science.gov (United States)

    Mena-Serrano, A P; Parreiras, S O; do Nascimento, E M S; Borges, C P F; Berger, S B; Loguercio, A D; Reis, A

    2015-01-01

    In tooth whitening, the hydrogen peroxide (HP) diffuses in the enamel and dentin, reaching the pulp. This in vitro study aimed to quantify the penetration of HP in the pulp chamber in teeth submitted to bleaching agents of different concentrations of HP without calcium (HP 20% [20CF], HP 35% [35CF]) and with calcium (HP 20% [20CC], HP 35% [35CC]). Fifty human premolars were sectioned 3 mm from the cemento-enamel junction and the pulp tissue was removed. The teeth were divided into five groups according to treatment and with a control group (n=10). An acetate buffer solution was placed in the pulp chamber of all teeth. The control group was exposed only to distilled water, while the other groups were treated with a bleaching procedure, according to the manufacturer's recommendations. After treatment, the acetate buffer solution was transferred to a glass tube in which leuco-crystal violet and peroxidase solutions were added, resulting in a blue solution. The optical density of this blue solution was determined spectrophotometrically and converted into micrograms equivalent to the HP. Data were analyzed using analysis of variance and Tukey tests (α=0.05). The HP concentration did not affect the HP inside the pulp chamber, but the presence of calcium significantly reduced it (p<0.0001). The amount of HP that reaches the pulp chamber depends on the bleaching protocol and the product employed, and it seems to be less affected by HP concentration.

  14. Hydrothermal carbonization of autoclaved municipal solid waste pulp and anaerobically treated pulp digestate

    Science.gov (United States)

    In this study, the autoclaved organic fraction of municipal solid waste pulp (OFMSW) and the digestate from OFMSW pulp after anaerobic digestion (AD) were processed by hydrothermal carbonization (HTC) at 200, 250, and 300 °C for 30 min and 2 h. The focus of this work was to evaluate the potential fo...

  15. Extracellular matrix of dental pulp stem cells: Applications in pulp tissue engineering using somatic MSCs

    Directory of Open Access Journals (Sweden)

    Sriram eRavindran

    2014-01-01

    Full Text Available Dental Caries affects approximately 90% of the world’s population. At present, the clinical treatment for dental caries is root canal therapy. This treatment results in loss of tooth sensitivity and vitality. Tissue engineering can potentially solve this problem by enabling regeneration of a functional pulp tissue. Dental pulp stem cells (DPSCs have been shown to be an excellent source for pulp regeneration. However, limited availability of these cells hinders its potential for clinical translation. We have investigated the possibility of using somatic mesenchymal stem cells from other sources for dental pulp tissue regeneration using a biomimetic dental pulp extracellular matrix (ECM incorporated scaffold. Human periodontal ligament stem cells (PDLSCs and human bone marrow stromal cells (HMSCs were investigated for their ability to differentiate towards an odontogenic lineage. In vitro real-time PCR results coupled with histological and immunohistochemical examination of the explanted tissues confirmed the ability of PDLSCs and HMSCs to form a vascularized pulp-like tissue. These findings indicate that the dental pulp stem derived ECM scaffold stimulated odontogenic differentiation of PDLSCs and HMSCs without the need for exogenous addition of growth and differentiation factors. This study represents a translational perspective toward possible therapeutic application of using a combination of somatic stem cells and extracellular matrix for pulp regeneration.

  16. EVALUATION OF LINERBOARD PROPERTIES FROM MALAYSIAN CULTIVATED KENAF SODA-ANTHRAQUINONE PULPS VERSUS COMMERCIAL PULPS

    Directory of Open Access Journals (Sweden)

    Ahmad Azizi Mossello

    2010-06-01

    Full Text Available Malaysian cultivated kenaf has been identified as a suitable raw material for linerboard production. This study examines the soda-antraquinone (soda-AQ pulp of kenaf fibers versus old corrugated container (OCC and unbleached softwood kraft pulps as the main sources for linerboard production. The results showed significant differences among the pulp properties. The unbleached kraft pulp with very high freeness required high beating to reach an optimized freeness and produced paper with the highest strength properties, except for tear resistance. The OCC gave paper with the lowest strength properties. In the case of kenaf fractions, bast pulp with high freeness needed less beating than softwood and produced paper with high tear resistance. Core fiber, which had the lowest freeness and highest drainage time, led to paper with high strength but very low tear resistance. Kenaf whole stem pulp showed intermediate properties between core and bast and close to those of unbleached softwood pulp, but with very lower beating requirement. Finally, kenaf whole stem, due to its strength properties, moderate separation cost, and simple pulping process, was judged to be more suitable for commercialization for linerboard production in Malaysia.

  17. REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

    Directory of Open Access Journals (Sweden)

    Guanglei Zhao

    2010-06-01

    Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

  18. Bioceramic/Poly (glycolic-poly (lactic acid composite induces mineralized barrier after direct capping of rat tooth pulp tissue

    Directory of Open Access Journals (Sweden)

    Alfonso Gala-Garcia

    2010-03-01

    Full Text Available The aim of this study was to observe the histopathological pulp response following direct pulp capping of mechanically exposed teeth in rats with a composite of beta-tricalcium phosphate-hydroxyapatite bioceramic (BC and poly (glycolic-poly (lactic acid (PLGA material or a calcium hydroxide [Ca(OH2] material, compared to BC alone and a negative control of water. Pulp of the maxillary molars was exposed, followed by capping with the experimental material. The pulpal tissue response was assessed post-operatively at 1, 7, 14 and 30 d, followed by histological analysis. The Ca(OH2 group exhibited severe acute inflammatory cell infiltration at day 14. However after 30 d, a new hard tissue with macro porous obliteration of the pulp chamber and a characteristic necrotic area had appeared. BC and Ca(OH2 capping were associated with moderate inflammation and dentinal bridge similar. Meanwhile, in the BC/PLGA composite group, there was moderate inflammatory infiltrate and formation of a dense and complete dentinal bridge. In conclusion, the BC/PLGA composite material showed a large zone of tertiary dentin, and effectively reorganized the dentin-pulp complex.

  19. PULP OBTAINING METHOD FOR PACKAGE PRODUCTION

    Directory of Open Access Journals (Sweden)

    V. V. Kuzmich

    2015-01-01

    Full Text Available The paper presents a new method for obtaining pulp which is used for production of cardboard, paper and package while using carbon dioxide and hydrazine hydrate and neutral-sulfite  shive cooking. Output increase of  the desired product can be explained by reduction in destruction of plant raw material carbohydrates during its cooking process. Quality improvement of the desired product (improvement in bleaching and output is attributed to the fact that usage of carbon dioxide and hydrazine contributes to provision of polysaccharide chain resistance to destruction due to the presence of  end links having structure of metasaccharinic and aldonic acids.The author has developed a new method for pulp obtaining on the basis of the executed investigations  and literature data.  СО2 and hydrazine hydrate have been used for obtaining pulp. Method invention concerns pulp obtaining and it can be used for paper and cardboard package manufacturing in pulp and paper industry.The method is to be carried in the following way: pulp-containing plant raw material is loaded into an autoclave and then aqua solution of sodium monosulfite containing hydrazine hydrate that constitutes 4–5 % of absolute dry pulp-containing raw material mass with liquid module 1:6–1:8 is supplied into the autoclave. The autoclave is closed for operation under pressure and the solution is carbonated under pressure which constitutes 5–8 % of absolute dry plant raw material (shover. Temperature is subsequently raised up to 180 °С in the space of 2 hours and cooking is carried out in the course of 4 hours. Usage of  the proposed method for shover cooking makes it possible to reduce monosulfite cooking process and improve qualitative characteristics and output of the desired product.  In addition to above mentioned fact there is a possibility to improve bleaching and final product output. 

  20. Final chlorine dioxide stage at near-neutral pH for bleaching eucalypt pulp

    Directory of Open Access Journals (Sweden)

    Robisnéa A. Ribeiro

    2014-01-01

    Full Text Available It is well known that pH is an important parameter for controlling the eucalyptus pulp bleaching when using the final chlorine dioxide stage, since it affects the effectiveness of the process. Recommendations found in the literature for operating are in the 3.5 to 4.0 range. However, in this paper it was shown that final chlorine dioxide has better performance, with significant brightness gain while also preserving pulp quality, when it is operated at near neutral pH. This result can be explained by the generation of sodium bicarbonate in situ upon adding carbon dioxide at this stage.

  1. The Potential of Coffee Husk and Pulp as an Alternative Source of ...

    African Journals Online (AJOL)

    In Ethiopia enormous amounts of coffee husk and pulp are generated anually from coffee processing industries. However, they have been poorly utilized or left to decompose or otherwise dumped in the environment. Therefore, this research was conducted at Teppi and Limu coffee farms in Ethiopia to produce briquettes ...

  2. A multi-criteria decision analysis of management alternatives for anaerobically digested kraft pulp mill sludge.

    Directory of Open Access Journals (Sweden)

    Martijn Eikelboom

    Full Text Available The Multi-Criteria Decision Analysis (MCDA procedure was used to compare waste management options for kraft pulp mill sludge following its anaerobic digestion. Anaerobic digestion of sludge is advantageous because it produces biogas that may be used to generate electricity, heat and biofuels. However, adequate management of the digested sludge is essential. Landfill disposal is a non-sustainable waste management alternative. Kraft pulp mill digested sludge applied to land may pose risks to the environment and public health if the sludge has not been properly treated. This study is aimed to compare several recycling alternatives for anaerobically digested sludge from kraft pulp mills: land application, landfill disposal, composting, incineration, pyrolysis/gasification, and biofuel production by algae. The MCDA procedure considered nine criteria into three domains to compare digested sludge recycling alternatives in a kraft pulp mill: environmental (CO2 emission, exposure to pathogens, risk of pollution, material and energy recovery, economic (overall costs, value of products and technical (maintenance and operation, feasibility of implementation. The most suitable management options for digested sludge from kraft pulp mills were found to be composting and incineration (when the latter was coupled with recycling ash to the cement industry. Landfill disposal was the worst option, presenting low performance in feasibility of implementation, risk of pollution, material and energy recovery.

  3. A multi-criteria decision analysis of management alternatives for anaerobically digested kraft pulp mill sludge

    Science.gov (United States)

    Eikelboom, Martijn; Lopes, Alice do Carmo Precci; Silva, Claudio Mudadu; Rodrigues, Fábio de Ávila; Zanuncio, José Cola

    2018-01-01

    The Multi-Criteria Decision Analysis (MCDA) procedure was used to compare waste management options for kraft pulp mill sludge following its anaerobic digestion. Anaerobic digestion of sludge is advantageous because it produces biogas that may be used to generate electricity, heat and biofuels. However, adequate management of the digested sludge is essential. Landfill disposal is a non-sustainable waste management alternative. Kraft pulp mill digested sludge applied to land may pose risks to the environment and public health if the sludge has not been properly treated. This study is aimed to compare several recycling alternatives for anaerobically digested sludge from kraft pulp mills: land application, landfill disposal, composting, incineration, pyrolysis/gasification, and biofuel production by algae. The MCDA procedure considered nine criteria into three domains to compare digested sludge recycling alternatives in a kraft pulp mill: environmental (CO2 emission, exposure to pathogens, risk of pollution, material and energy recovery), economic (overall costs, value of products) and technical (maintenance and operation, feasibility of implementation). The most suitable management options for digested sludge from kraft pulp mills were found to be composting and incineration (when the latter was coupled with recycling ash to the cement industry). Landfill disposal was the worst option, presenting low performance in feasibility of implementation, risk of pollution, material and energy recovery. PMID:29298296

  4. Suitability of Different Natural and Synthetic Biomaterials for Dental Pulp Tissue Engineering.

    Science.gov (United States)

    Galler, Kerstin M; Brandl, Ferdinand P; Kirchhof, Susanne; Widbiller, Matthias; Eidt, Andreas; Buchalla, Wolfgang; Göpferich, Achim; Schmalz, Gottfried

    2018-02-01

    Dental pulp tissue engineering is possible after insertion of pulpal stem cells combined with a scaffold into empty root canals. Commonly used biomaterials are collagen or poly(lactic) acid, which are either difficult to modify or to insert into such a narrow space. New hydrogel scaffolds with bioactive, specifically tailored functions could optimize the conditions for this approach. Different synthetic and natural hydrogels were tested for their suitability to engineer dental pulp. Two functionalized modifications of polyethylene glycol were developed in this study and compared to a self-assembling peptide, as well as to collagen and fibrin. Cell viability of dental pulp stem cells in test materials was assessed over two weeks. Cells in selected test materials laden with dentin-derived growth factors were inserted into human tooth roots and implanted subcutaneously into immunocompromised mice. In vitro cell culture exhibited distinct differences between scaffold types, where viability was significantly higher in natural compared to synthetic materials. In vivo experiments showed considerable differences regarding scaffold degradation, soft tissue formation, vascularization, and odontoblast-like cell differentiation. Fibrin appeared most suitable to enable generation of a pulp-like tissue and differentiation of cells into odontoblasts at the cell-dentin interface. In conclusion, natural materials, especially fibrin, proved to be superior compared to synthetic scaffolds regarding cell viability and dental pulp-like tissue formation.

  5. Cogeneration of electric energy: The case of pulp and paper mills

    International Nuclear Information System (INIS)

    Harberger, A.C.

    1993-01-01

    Applied welfare economics are utilized to analyze the phenomenon of cogeneration of electricity in the pulp and paper sector. Optimum levels of energy use (and of cogeneration) are defined, and the efficiency costs of various possible deviations from the optimum are shown. An economic analysis is presented of the effects of cost of electricity for the pulp and paper industry, and the impact that cogeneration can have on these costs. The social welfare impacts of cogeneration and electricity subsidies are discussed, together with the issue of crosshauling. It is shown that in Canada a policy focusing on cogeneration without crosshauling leads to optimal results. An added argument against crosshauling involves the implicit transfers involved. These transfers generate benefits for the pulp and paper mills at the expense of the electricity utility and its paying customers or taxpaying public. A strong argument is proposed against allowing of crosshauling

  6. Dens invaginatus with necrotic pulp in a right maxillary lateral incisor with preserved vitality.

    Science.gov (United States)

    Alessandro, Lanza; Fabrizio, Di Francesco; Gennaro, De Marco; Dario, Di Stasio; Eugenio, Guidetti; Letizia, Perillo; Luigi, Femiano; Felice, Femiano

    2018-01-01

    Dens invaginatus (DI) is a dental malformation occurring in several morphologic types. Consequently, treatment of teeth affected by DI can get complicated because of the complex root canal anatomy. The aim is to describe how to manage a rare report of a DI with necrotic pulp held within the vital pulp of a maxillary lateral incisor. Oral fistula was found on the buccal mucosa of the apex of the vital maxillary lateral incisor with a DI having necrotic pulp. Endodontic treatment of the maxillary lateral incisor and of the tract canal of DI was realized. Clinical disappearance of oral sinus tract was observed after 10 days. On the contrary, the disappearance of radiolucent area occurred after 6 months. A proper and prompt diagnosis is necessary to carry out effective prevention protocols or prevent consequences generating nonrecoverable endo-perio diseases.

  7. Epigenetic regulation in dental pulp inflammation

    Science.gov (United States)

    Hui, T; Wang, C; Chen, D; Zheng, L; Huang, D; Ye, L

    2016-01-01

    Dental caries, trauma, and other possible factors could lead to injury of the dental pulp. Dental infection could result in immune and inflammatory responses mediated by molecular and cellular events and tissue breakdown. The inflammatory response of dental pulp could be regulated by genetic and epigenetic events. Epigenetic modifications play a fundamental role in gene expression. The epigenetic events might play critical roles in the inflammatory process of dental pulp injury. Major epigenetic events include methylation and acetylation of histones and regulatory factors, DNA methylation, and small non-coding RNAs. Infections and other environmental factors have profound effects on epigenetic modifications and trigger diseases. Despite growing evidences of literatures addressing the role of epigenetics in the field of medicine and biology, very little is known about the epigenetic pathways involved in dental pulp inflammation. This review summarized the current knowledge about epigenetic mechanisms during dental pulp inflammation. Progress in studies of epigenetic alterations during inflammatory response would provide opportunities for the development of efficient medications of epigenetic therapy for pulpitis. PMID:26901577

  8. BLEACHING EUCALYPTUS PULPS WITH SHORT SEQUENCES

    Directory of Open Access Journals (Sweden)

    Flaviana Reis Milagres

    2011-03-01

    Full Text Available Eucalyptus spp kraft pulp, due to its high content of hexenuronic acids, is quite easy to bleach. Therefore, investigations have been made attempting to decrease the number of stages in the bleaching process in order to minimize capital costs. This study focused on the evaluation of short ECF (Elemental Chlorine Free and TCF (Totally Chlorine Free sequences for bleaching oxygen delignified Eucalyptus spp kraft pulp to 90% ISO brightness: PMoDP (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, PMoD/P (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, without washing PMoD(PO (Molybdenum catalyzed acid peroxide, chlorine dioxide and pressurized peroxide, D(EPODP (chlorine dioxide, extraction oxidative with oxygen and peroxide, chlorine dioxide and hydrogen peroxide, PMoQ(PO (Molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide, and XPMoQ(PO (Enzyme, molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide. Uncommon pulp treatments, such as molybdenum catalyzed acid peroxide (PMo and xylanase (X bleaching stages, were used. Among the ECF alternatives, the two-stage PMoD/P sequence proved highly cost-effective without affecting pulp quality in relation to the traditional D(EPODP sequence and produced better quality effluent in relation to the reference. However, a four stage sequence, XPMoQ(PO, was required to achieve full brightness using the TCF technology. This sequence was highly cost-effective although it only produced pulp of acceptable quality.

  9. Exposing diversity

    DEFF Research Database (Denmark)

    Nørtoft, Kamilla; Nordentoft, Helle Merete

    professionals´ meetings with patients and relatives. In the paper we draw data from focus group discussions with interdisciplinary groups of health care professionals working in the area of care for older people. The video narratives used to initiate discussions are developed through ethnographic fieldwork...... in the homes of older people and in pedagogical institutions targeting older people. In the paper we look at the potentials and challenges in working with ethnographic video narratives as a pedagogical tool. Our findings indicate that the use of video narratives has the potential to expose the diversity...... focus on their own professional discipline and its tasks 2) stimulates collaborative learning when they discuss their different interpretations of the ethnographic video narratives and achieve a deeper understanding of each other’s work and their clients’ lifeworlds, which might lead to a better...

  10. Sex ratio of the offspring of Sprague-Dawley rats exposed to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) in utero and lactationally in a three-generation study

    International Nuclear Information System (INIS)

    Rowlands, J.C.; Budinsky, R.A.; Aylward, L.L.; Faqi, A.S.; Carney, E.W.

    2006-01-01

    Reports of a decreased male/female sex ratio in children born to males exposed to TCDD in Seveso, Italy, at a young age have sparked examinations of this endpoint in other populations exposed to TCDD or related compounds. Overall, the male/female sex ratio results reported in these studies, with slightly different age-exposed male populations, have shown mixed results. Experimental studies of the effects of in utero exposure to TCDD in laboratory animals have reported no effect on the f 1 sex ratio and mixed results for the sex ratio of the f 2 generation. In order to better understand the potential effects of TCDD on second generation sex ratio, we retrieved archived data from a comprehensive three-generation feeding study of TCDD in rats that was conducted and published in the 1970s, but which did not publish data on sex ratio of the offspring [Murray, F.J., Smith, F.A., Nitschke, K.D., Humiston, C.G., Kociba, R.J., Schwetz, B.A., 1979. Three-generation reproduction study of rats given 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) in the diet. Toxicol. Appl. Pharmacol. 50, 241-252]. A re-examination of the original Murray et al. data found no statistically significant treatment-related changes in postnatal day 1 sex ratio in any generation of treated animals, consistent with one other relatively large study reporting on this endpoint. We discuss mechanistic data underlying a potential effect of TCDD on this endpoint. We conclude that the inconsistency in findings on sex ratio of the offspring of male rats exposed to TCDD in utero is likely due to random variation associated with a relatively small sample size, although differences between studies in strain of rat, dose regimen, and day of ascertainment of sex ratio cannot be ruled out

  11. Histological evaluation of direct pulp capping of rat pulp with experimentally developed low-viscosity adhesives containing reparative dentin-promoting agents.

    Science.gov (United States)

    Suzuki, Masaya; Taira, Yoshihisa; Kato, Chikage; Shinkai, Koichi; Katoh, Yoshiroh

    2016-01-01

    This study examines the wound healing process in exposed rat pulp when capped with experimental adhesive resin systems. Experimental adhesive resin system for direct pulp capping was composed of primer-I (PI), -II (PII), and -III (PIII) and an experimental bonding agent (EBA). PI was Clearfil(®) SE Bond(®)/Primer (CSP) containing 5.0 wt% CaCl2, PII was PI containing 10 wt% nanofiller (Aerosil(®) 380), and PIII was CSP containing 5.0 wt% of compounds of equal moles of synthetic peptides (pA and pB) derived from dentin matrix protein 1. EBA was Clearfil(®) SE Bond(®)/Bond (CSB) containing 10 wt% hydroxyapatite powders. Three experimental groups were designed. PI was assigned to experimental Groups 1 and 3. PII was assigned to experimental Groups 2 and 3. PIII and EBA were assigned to all experimental adhesive groups. Control teeth were capped with calcium hydroxide preparation (Dycal(®)), and CSP and CSB were applied to the cavity. The rats were sacrificed after each observation period (14, 28, 56, and 112 days). The following parameters were evaluated: pulp tissue disorganization, inflammatory cell infiltration, reparative dentin formation (RDF), and bacterial penetration. There were no significant differences among all the groups for all parameters and all observation periods (p>0.05, Kruskal-Wallis test). All groups showed initial RDF at 14 days postoperatively and extensive RDF until 112 days postoperatively. Groups 2 and 3 demonstrated higher quantity of mineralized dentin bridge formation compared with Group 1. Addition of nanofillers to the primer was effective in promoting high-density RDF. Experimentally developed adhesive resin systems induce the exposed pulp to produce almost the same quantity of reparative dentin as calcium hydroxide. However, we need further studies to elucidate whether the same results could be obtained in humans. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Enzymatic pulp upgrade for producing high-value cellulose out of a Kraft paper pulp.

    Science.gov (United States)

    Hutterer, Christian; Kliba, Gerhard; Punz, Manuel; Fackler, Karin; Potthast, Antje

    2017-07-01

    The high-yield separation of polymeric parts from wood-derived lignocellulosic material is indispensable in biorefinery concepts. For the separation of cellulose and xylan from hardwood paper pulps to obtain pulps of high cellulose contents, simple alkaline extractions were found to be the most suitable technology, although having certain limitations. These are embodied by residual alkali resistant xylan incorporated in the pulp matrix. Further purification in order to produce pure cellulose with a low uniformity could be achieved selectively degrading residual xylan and depolymerizing the cellulose macromolecules by xylanase and cellulase. The latter help to adjust cellulose chain lengths for certain dissolving pulp grades while reducing the demand for ozone in subsequent TCF bleaching. Experiments applying different commercially available enzyme preparations revealed the dependency of xylanase performance on the residual xylan content in pulps being stimulated by additional cellulase usage. The action of the latter strongly depends on the cellulose allomorphy confirming the impact of the pulp morphology. Hence, the combined application of both types of enzymes offers a high potential for upgrading pulps in order to produce a pure and high-value cellulose product. Copyright © 2017 Elsevier Inc. All rights reserved.

  13. Comparison of Calcium Hydroxide and Bioactive Glass after Direct Pulp Capping in Primary Teeth

    Directory of Open Access Journals (Sweden)

    R. Haghgoo

    2007-12-01

    Full Text Available Objective: Bioactive glass is often used as a filler material for repair of dental bone defects.In different studies osteogenic potential of this material was proved, but its dentinogenesisproperty is in doubt. The purpose of this study was to evaluate the histological pulp responses of Calcium hydroxide and Bioactive glass placed directly on exposed pulp tissues.Materials and Methods: Twenty teeth to be extracted due to orthodontic reasons were selected. These teeth were divided into two groups and treated with direct pulp capping.Calcium hydroxide was used for 10 teeth and Bioactive glass for 10 teeth. After 60 daysthe teeth were extracted and prepared for histological evaluation. Finally the data was analyzed with exact Fisher test.Results: All teeth treated with Calcium hydroxide showed inflammation. Internal resorption was seen in six teeth, abscess in five teeth and dentinal bridge in two teeth. Inflammationwas seen in three Bioactive glass samples and dentinal bridge in seven teeth, but internal resorption and abscess were not seen.Conclusion: Bioactive glass appears to be superior to Calcium hydroxide as a pulp capping agent in primary teeth.

  14. Innervated boomerang flap for finger pulp reconstruction.

    Science.gov (United States)

    Chen, Shao-Liang; Chiou, Tai-Fung

    2007-11-01

    The boomerang flap originates from the dorsolateral aspect of the proximal phalanx of an adjacent digit and is supplied by the retrograde blood flow through the vascular arcades between the dorsal and palmar digital arteries. To provide sensation of the boomerang flap for finger pulp reconstruction, the dorsal sensory branch of the proper digital nerve and the superficial sensory branch of the corresponding radial or ulnar nerve are included within the skin flap. After transfer of the flap to the injured site, epineural neurorrhaphies are done between the digital nerves of the pulp and the sensory branches of the flap. We used this sensory flap in five patients, with more than 1 year follow-up, and all patients achieved measurable two-points discrimination. The boomerang flap not only preserves the proper palmar digital artery but also provides an extended and innervated skin paddle. It seems to be an alternative choice for one-stage reconstruction of major pulp defect.

  15. Integrated chemical plants at the pulp mill

    Energy Technology Data Exchange (ETDEWEB)

    Ehtonen, P.; Hurme, M.; Jaervelaeinen, M.

    1995-12-31

    The goal of this paper is to present how the chemical plants can be integrated to the pulp mill. The integration renders possible to balance the chemical consumptions. The total mass balance of a pulp mill with the incoming fuel material and the outgoing waste and flue gases are discussed. The balance figures are presented for the chemicals of the modern fibre line, which will produce fully bleached softwood pulp with an improved effluent quality. The main benefits are lower chemical and transportation costs. The principal over-all plant process block diagrams and process descriptions are presented. The presented info system provides real time information on process and production status at overall mill and department levels. (author)

  16. Sisal organosolv pulp as reinforcement for cement based composites

    OpenAIRE

    Joaquim, Ana Paula; Tonoli, Gustavo Henrique Denzin; Santos, Sérgio Francisco Dos; Savastano Junior, Holmer

    2009-01-01

    The present work describes non-conventional sisal (Agave sisalana) chemical (organosolv) pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP) fibres were produced by the slurry de-watering and pressin...

  17. Mesenchymal Stem Cells Derived from Dental Pulp: A Review

    Directory of Open Access Journals (Sweden)

    Edgar Ledesma-Martínez

    2016-01-01

    Full Text Available The mesenchymal stem cells of dental pulp (DPSCs were isolated and characterized for the first time more than a decade ago as highly clonogenic cells that were able to generate densely calcified colonies. Now, DPSCs are considered to have potential as stem cell source for orthopedic and oral maxillofacial reconstruction, and it has been suggested that they may have applications beyond the scope of the stomatognathic system. To date, most studies have shown that, regardless of their origin in third molars, incisors, or exfoliated deciduous teeth, DPSCs can generate mineralized tissue, an extracellular matrix and structures type dentin, periodontal ligament, and dental pulp, as well as other structures. Different groups worldwide have designed and evaluated new efficient protocols for the isolation, expansion, and maintenance of clinically safe human DPSCs in sufficient numbers for various therapeutics protocols and have discussed the most appropriate route of administration, the possible contraindications to their clinical use, and the parameters to be considered for monitoring their clinical efficacy and proper biological source. At present, DPSC-based therapy is promising but because most of the available evidence was obtained using nonhuman xenotransplants, it is not a mature technology.

  18. Arundo donax L. reed: new perspectives for pulping and bleaching. Part 4. Peroxide bleaching of organosolv pulps.

    Science.gov (United States)

    Shatalov, A A; Pereira, H

    2005-05-01

    A comparative study on TCF (totally chlorine-free) bleachability of organosolv pulps from the annual fibre crop Arundo donax L. (giant reed) was carried out using a simple three-stage peroxide bleaching sequence without oxygen pre-bleaching. ASAM (alkali-sulfite-anthraquinone-methanol), Organocell (alkali-anthraquinone-methanol) and ethanol-soda organosolv pulps were bleached and compared with kraft pulp, as a reference. The final brightness of 76-78% ISO was attained for all tested pulps. The chemical charge required to reach this level of brightness varied for different pulps (despite the equal initial content of the residual lignin) and directly related to starting brightness values. No direct correlation between brightness improvement and lignin removal during bleaching was found, indicating the influence of the specific pulp properties introduced by pulping process on bleaching chemistry. The general higher bleaching response of organosolv pulps from A. donax was noted in comparison with kraft.

  19. Effects of transportation time after extraction on the magnetic cryopreservation of pulp cells of rat dental pulp

    Directory of Open Access Journals (Sweden)

    Mao-Suan Huang

    2011-03-01

    Conclusions: The freezing technique used in this animal study provided positive effects on pulp cell storage. In addition, the storage time before the freezing procedure is an important issue for cryopreserving pulp cells in intact teeth.

  20. Ranking mechanical pulps for their potential to photoyellow

    Science.gov (United States)

    Umesh P. Agarwal

    2000-01-01

    Recently found experimental evidence has provided strong support for an alternative photoyellowing mechanism that suggests that pulp- photoyellowing occurs due to direct photooxidation of hydroquinones (present in mechanical pulps) top-quinones. Because hydroquinones were found to be present in pulps, it may be possible to quantify them. Quantification of mechanical-...

  1. 78 FR 31315 - Kraft Pulp Mills NSPS Review

    Science.gov (United States)

    2013-05-23

    ... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

  2. Comparative study of percentage yield of pulp from various Nigerian ...

    African Journals Online (AJOL)

    user

    also other applications like in the chemical industry. (Biermann, 1993). Therefore pulp is a very .... digester was maintained at an operating condition of. 170°C, pressure of 2 bars, with liquor to wood ratio of 4:1. Cooking ... The effects of different concentrations of pulping liquor on the yield of pulp from the wood species are ...

  3. Organosolv pulping and test paper characterization of fiber hemp

    NARCIS (Netherlands)

    Zomers, F.H.A.; Gosselink, R.J.A.; Dam, van J.E.G.; Tjeerdsma, B.F.

    1995-01-01

    The autocatalyzed ethanol pulping of hemp to produce chemical-grade pulp was examined. Batch delignification conditions were developed for hemp core, hemp bast, and hemp whole stem. Although successful pulping of both hemp core and bast fibre is possible, further research is necessary.

  4. Betatron activation analysis of cupriferous flotation pulp

    International Nuclear Information System (INIS)

    Kaminski, R.; Matenko, J.; Mencel, J.; Janiczek, J.; Kielsznia, J.

    1974-01-01

    A method of copper determination in cupriferous flotation pulp by photo-activation analysis using betatron and another equipments of existent ''analytical line'' intended for copper determination in dry samples has been described. An activation has been achieved with 14.9 MeV γ-photons. The excitation activity was investigated by using two scintillation detectors and a fast coincidence circuit with resolution time 80 ns. The precision of method was determined as +- 4.25% in 0.95 confidence level for pulp with concentration 5% Cu and +- 24% for 0.06% Cu. (author)

  5. Kraft pulping and ECF bleaching of Eucalyptus globulus pretreated by the white-rot fungus Ceriporiopsis subvermispora - doi: 10.4025/actascitechnol.v34i3.12410

    Directory of Open Access Journals (Sweden)

    Claudio Salazar

    2012-05-01

    Full Text Available Eucalyptus globulus wood chips were decayed by the lignin-degrading fungus Ceriporiopsis subvermispora as a pretreatment step before kraft pulping. Weight and component losses of wood after the biotreatment were the following: weight (5%, glucans (1.5%, xylans (4.3%, lignin (5.7% and extractives (57.5%. The residual amount of lignin (expressed by the kappa number in pulps from biotreated wood chips was lower than that of pulps from the undecayed control. Depending on the delignification degree, kraft biopulps presented similar or up to 4% increase in pulp yield and 20% less hexenuronic acids (HexA than control pulps. The extended delignification with O2 decreases approximately 50% of the kappa number of the pulps and increases brightness, but had no effect in HexA reduction. The bleaching steps with chlorine dioxide (D0ED1 sequence decreased the kappa number up to 97%, increased pulp brightness up to 84% ISO and decreased HexA amount up to 91%. The use of C. subvermispora in biopulping of E. globulus generated important benefits during the production of kraft pulps that are reflected in a high pulp yield, low residual lignin content, low HexA amount, high brightness and viscosity of the biopulps as compared with pulps produced from untreated wood chips.

  6. Decellularized Human Dental Pulp as a Scaffold for Regenerative Endodontics.

    Science.gov (United States)

    Song, J S; Takimoto, K; Jeon, M; Vadakekalam, J; Ruparel, N B; Diogenes, A

    2017-06-01

    Teeth undergo postnatal organogenesis relatively late in life and only complete full maturation a few years after the crown first erupts in the oral cavity. At this stage, development can be arrested if the tooth organ is damaged by either trauma or caries. Regenerative endodontic procedures (REPs) are a treatment alternative to conventional root canal treatment for immature teeth. These procedures rely on the transfer of apically positioned stem cells, including stem cells of the apical papilla (SCAP), into the root canal system. Although clinical success has been reported for these procedures, the predictability of expected outcomes and the organization of the newly formed tissues are affected by the lack of an available suitable scaffold that mimics the complexity of the dental pulp extracellular matrix (ECM). In this study, we evaluated 3 methods of decellularization of human dental pulp to be used as a potential autograft scaffold. Tooth slices of human healthy extracted third molars were decellularized by 3 different methods. One of the methods generated the maximum observed decellularization with minimal impact on the ECM composition and organization. Furthermore, recellularization of the scaffold supported the proliferation of SCAP throughout the scaffold with differentiation into odontoblast-like cells near the dentinal walls. Thus, this study reports that human dental pulp from healthy extracted teeth can be successfully decellularized, and the resulting scaffold supports the proliferation and differentiation of SCAP. The future application of this form of an autograft in REPs can fulfill a yet unmet need for a suitable scaffold, potentially improving clinical outcomes and ultimately promoting the survival and function of teeth with otherwise poor prognosis.

  7. Ectopic Hard Tissue Formation by Odonto/Osteogenically In Vitro Differentiated Human Deciduous Teeth Pulp Stem Cells.

    Science.gov (United States)

    Kim, Seunghye; Song, Je Seon; Jeon, Mijeong; Shin, Dong Min; Kim, Seong-Oh; Lee, Jae Ho

    2015-07-01

    There have been many attempts to use the pulp tissue from human deciduous teeth for dentin or bone regeneration. The objective of this study was to determine the effects of odonto/osteogenic in vitro differentiation of deciduous teeth pulp stem cells (DTSCs) on their in vivo hard tissue-forming potential. DTSCs were isolated from extracted deciduous teeth using the outgrowth method. These cells were exposed to odonto/osteogenic stimuli for 4 and 8 days (Day 4 and Day 8 groups, respectively), while cells in the control group were cultured in normal medium. The in vitro differentiated DTSCs and the control DTSCs were transplanted subcutaneously into immunocompromised mice with macroporous biphasic calcium phosphate and sacrificed at 8 weeks post-implantation. The effect of odonto/osteogenic in vitro differentiation was evaluated using alkaline phosphatase (ALP) staining and quantitative reverse transcription polymerase chain reaction (RT-PCR). The in vivo effect was evaluated by qualitative RT-PCR, assessment of ALP activity, histologic analysis, and immunohistochemical staining. The amount of hard tissue was greater in Day 4 group than Day 8 group (p = 0.014). However, Day 8 group generated lamellar bone-like structure, which was immunonegative to anti-human dentin sialoprotein with significantly low expression level of DSPP compared with the control group (p = 0.008). This study demonstrates that odonto/osteogenic in vitro differentiation of DTSCs enhances the formation of bone-like tissue, instead of dentin-like tissue, when transplanted subcutaneously using MBCP as a carrier. The odonto/osteogenic in vitro differentiation of DTSCs may be an effective modification that enhances in vivo bone formation by DTSCs.

  8. Effects of Soda-Anthraquinone Pulping Variables on the Durian Rind Pulp and Paper Characteristics: A Preliminary Test

    Science.gov (United States)

    Rizal Masrol, Shaiful; Irwan Ibrahim, Mohd Halim; Adnan, Sharmiza; Rahmad Talib, Mohd; Sian, Lau Lee

    2017-08-01

    Good combination of pulping variables is required to obtain the quality pulp and paper characteristics. Thus, in this preliminary work, naturally dried durian rind were pulped under Soda-Anthraquinone (Soda-AQ) pulping process with 18% to 22% alkali charge, 0% to 0.1% Anthraquinone (AQ) charge, 90 minutes to 150 minutes of cooking time and 150°C to 170°C to investigate the effect of pulping variables on the characteristics of the pulp and paper. Pulping condition with 0% of AQ charge was also conducted for comparison. Results indicated that the best screen yield percentage, reject yield percentage, freeness, drainage time, tear index, number of folds and optical properties were shown by the pulp produced with combination of the highest active alkali (22%), AQ charge (0.1%), cooking time (150 minutes) and cooking temperature (170°C) except apparent density, tensile index and burst index. This preliminary result shows that the optimum quality of durian rind pulp as a potential papermaking raw material pulp could be produced by selecting the good combination of pulping variables which influences the pulp and paper characteristics.

  9. Transforming growth factor-β-induced gene product-h3 inhibits odontoblastic differentiation of dental pulp cells.

    Science.gov (United States)

    Serita, Suguru; Tomokiyo, Atsushi; Hasegawa, Daigaku; Hamano, Sayuri; Sugii, Hideki; Yoshida, Shinichiro; Mizumachi, Hiroyuki; Mitarai, Hiromi; Monnouchi, Satoshi; Wada, Naohisa; Maeda, Hidefumi

    2017-06-01

    The aim of this study was to investigate transforming growth factor-β-induced gene product-h3 (βig-h3) expression in dental pulp tissue and its effects on odontoblastic differentiation of dental pulp cells (DPCs). A rat direct pulp capping model was prepared using perforated rat upper first molars capped with mineral trioxide aggregate cement. Human DPCs (HDPCs) were isolated from extracted teeth. βig-h3 expression in rat dental pulp tissue and HDPCs was assessed by immunostaining. Mineralization of HDPCs was assessed by Alizarin red-S staining. Odontoblast-related gene expression in HDPCs was analyzed by quantitative RT-PCR. Expression of βig-h3 was detected in rat dental pulp tissue, and attenuated by direct pulp capping, while expression of interleukin-1β and tumor necrosis factor-α was increased in exposed pulp tissue. βig-h3 expression was also detected in HDPCs, with reduced expression during odontoblastic differentiation. The above cytokines reduced βig-h3 expression in HDPCs, and promoted their mineralization. Recombinant βig-h3 inhibited the expression of odontoblast-related genes and mineralization of HDPCs, while knockdown of βig-h3 gene expression promoted the expression of odontoblast-related genes in HDPCs. The present findings suggest that βig-h3 in DPCs may be involved in reparative dentin formation and that its expression is likely to negatively regulate this process. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Method for rapidly determining a pulp kappa number using spectrophotometry

    Science.gov (United States)

    Chai, Xin-Sheng; Zhu, Jun Yong

    2002-01-01

    A system and method for rapidly determining the pulp kappa number through direct measurement of the potassium permanganate concentration in a pulp-permanganate solution using spectrophotometry. Specifically, the present invention uses strong acidification to carry out the pulp-permanganate oxidation reaction in the pulp-permanganate solution to prevent the precipitation of manganese dioxide (MnO.sub.2). Consequently, spectral interference from the precipitated MnO.sub.2 is eliminated and the oxidation reaction becomes dominant. The spectral intensity of the oxidation reaction is then analyzed to determine the pulp kappa number.

  11. Effect of Urea Addition on Soda Pulping of Oak Wood

    OpenAIRE

    Cho, Nam-Seok; Matsumoto, Yuji; Cho, Hee-Yeon; Shin, Soo-Jeong; Oga, Shoji

    2008-01-01

    Many studies have been conducted to find a sulfur-free additive for alkaline pulping liquors that would have an effect similar to that of sulfide in kraft pulping. Some reagents that partially fulfill this role have been found, but they are too expensive to be used in the quantities required to make them effective. As an alternative method to solve air pollution problem and difficulty of pulp bleaching of kraft pulping process, NaOH-Urea pulping was applied. The properties of NaOH-Urea pul...

  12. Pulp and paper from oil palm fronds: Wavelet neural networks modeling of soda-ethanol pulping

    OpenAIRE

    Zarita Zainuddin; Wan Rosli Wan Daud; Pauline Ong; Amran Shafie

    2012-01-01

    Wavelet neural networks (WNNs) were used to investigate the influence of operational variables in the soda-ethanol pulping of oil palm fronds (viz. NaOH concentration (10-30%), ethanol concentration (15-75%), cooking temperature (150-190 ºC), and time (60-180 min)) on the resulting pulp and paper properties (viz. screened yield, kappa number, tensile index, and tear index). Performance assessments demonstrated the predictive capability of WNNs, in that the experimental results of the dependen...

  13. Fungal biomass production from coffee pulp juice

    Energy Technology Data Exchange (ETDEWEB)

    De Leon, R.; Calzada, F.; Herrera, R.; Rolz, C.

    1980-01-01

    Coffee pulp or skin represents about 40% of the weight of the fresh coffee fruit. It is currently a waste and its improper handling creates serious pollution problems for coffee producing countries. Mechanical pressing of the pulp will produce two fractions: coffee pulp juice (CPJ) and pressed pulp. Aspergillus oryzae, Trichoderma harzianum, Penicillium crustosum and Gliocladium deliquescens grew well in supplemented CPJ. At shake flask level the optimum initial C/N ratio was found to be in the range of 8 to 14. At this scale, biomass values of up to 50 g/l were obtained in 24 hours. Biomass production and total sugar consumption were not significantly different to all fungal species tested at the bench-scale level, even when the initial C/N ratio was varied. Best nitrogen consumption values were obtained when the initial C/N ratio was 12. Maximum specific growth rates occurred between 4-12 hours for all fungal species tested. (Refs. 8).

  14. Enrichment of coal pulps by selective flocculation

    Energy Technology Data Exchange (ETDEWEB)

    Blaschke, Z

    1977-01-01

    The results are presented of selective flocculation of coal pulps using different reagents. In some tests the coal particles were flocculated, and in others the coal remained in suspension and the dirt was flocculated. Selective flocculation makes it possible to obtain coal concentrates with a very low ash content from slurries with a high ash content. (In Polish)

  15. Enrichment of coal pulps by selective flocculation

    Energy Technology Data Exchange (ETDEWEB)

    Blaschke, Z

    1977-01-01

    The results are presented of selective flocculation of coal pulps using different reagents. In some tests the coal particles were flocculated, and in others the coal remained in suspension and the dirt was flocculated. Selective flocculation makes it possible to obtain coal concentrates with a very low ash content from slurries with a high ash content.

  16. Pulp-Capping with Mineral Trioxide Aggregate

    Directory of Open Access Journals (Sweden)

    Peycheva Kalina

    2015-11-01

    Full Text Available There are two considerations for direct pulp capping - accidental mechanical pulp exposure and exposure caused by caries. Mineral trioxide aggregate (MTA was used as pulp-capping material to preserve the vitality of the pulpal tissues. Follow-up examinations revealed that treatment was successful in preserving pulpal vitality and continued development of the tooth. On the basis of available information, it appears that MTA is the material of choice for some clinical applications. Material and methods: Cases 18 - 8 teeth with grey MTA, 10 teeth with white MTA; diagnose: Pulpitis chronica ulcerosa, Electro pulpal test (EOD - 30-35 μA, pre-clinical X-ray - without changes in the structures, follow ups for 4 years. Successful treatments: without clinical symptoms and changes in the X-rays: 5 teeth with grey MTA, 8 teeth with white MTA for period of 4 years. Unsuccessful treatments: Clinical symptoms and sometimes changes in the X-ray: 3 with grey MTA, 2 with white MTA. MTA is an appropriate material for pulp-capping and follow-up examinations revealed that the treatment was successful in preserving pulpal vitality.

  17. Waste management from pulp and paper production in the European Union

    International Nuclear Information System (INIS)

    Monte, M.C.; Fuente, E.; Blanco, A.; Negro, C.

    2009-01-01

    Eleven million tonnes of waste are produced yearly by the European pulp and paper industry, of which 70% originates from the production of deinked recycled paper. Wastes are very diverse in composition and consist of rejects, different types of sludges and ashes in mills having on-site incineration treatment. The production of pulp and paper from virgin pulp generates less waste but the waste has similar properties to waste from the production of deinked pulp, although with less inorganics. Due to legislation and increased taxes, landfills are quickly being eliminated as a final destination for wastes in Europe, and incineration with energy recovery is becoming the main waste recovery method. Other options such as pyrolysis, gasification, land spreading, composting and reuse as building material are being applied, although research is still needed for optimization of the processes. Due to the large volumes of waste generated, the high moisture content of the waste and the changing waste composition as a result of process conditions, recovery methods are usually expensive and their environmental impact is still uncertain. For this reason, it is necessary to continue research on different applications of wastes, while taking into account the environmental and economic factors of these waste treatments

  18. Pulp regeneration by transplantation of dental pulp stem cells in pulpitis: a pilot clinical study.

    Science.gov (United States)

    Nakashima, Misako; Iohara, Koichiro; Murakami, Masashi; Nakamura, Hiroshi; Sato, Yayoi; Ariji, Yoshiko; Matsushita, Kenji

    2017-03-09

    Experiments have previously demonstrated the therapeutic potential of mobilized dental pulp stem cells (MDPSCs) for complete pulp regeneration. The aim of the present pilot clinical study is to assess the safety, potential efficacy, and feasibility of autologous transplantation of MDPSCs in pulpectomized teeth. Five patients with irreversible pulpitis were enrolled and monitored for up to 24 weeks following MDPSC transplantation. The MDPSCs were isolated from discarded teeth and expanded based on good manufacturing practice (GMP). The quality of the MDPSCs at passages 9 or 10 was ascertained by karyotype analyses. The MDPSCs were transplanted with granulocyte colony-stimulating factor (G-CSF) in atelocollagen into pulpectomized teeth. The clinical and laboratory evaluations demonstrated no adverse events or toxicity. The electric pulp test (EPT) of the pulp at 4 weeks demonstrated a robust positive response. The signal intensity of magnetic resonance imaging (MRI) of the regenerated tissue in the root canal after 24 weeks was similar to that of normal dental pulp in the untreated control. Finally, cone beam computed tomography demonstrated functional dentin formation in three of the five patients. Human MDPSCs are safe and efficacious for complete pulp regeneration in humans in this pilot clinical study.

  19. Radiation -adsorption treatment of pesticides by using wood pulp and bagasse pulp

    International Nuclear Information System (INIS)

    Abd El-Aal, S.E.; Sokker, S.S.; Dessooki, A.M.

    2005-01-01

    Alkaline pulping of pulp wood and bagasse using sodium hydroxide resulted in the reduction of lignin from the wood and bagasse fibers and consequently increase adsorption of the pesticide pollutants to these fibers. Three different types of pesticides were used in this study namely, metalaxyl, dicloran and arelon. which were irradiated at a dose of 4 kGy before adsorption treatment.The results show that moderate adsorption was observed for all pesticides when adsorption was carried out without alkaline pulping and irradiation. This is due to the presence of lignin which retard the adsorption process. Batch sorption experiments at different pH values (3, 7, 9) for the retention of these pesticides by pulp wood and pulp bagasse fibers indicated that sorption is governed by the interaction of the ionized form of these compounds with the polyhydroxyl structure of cellulose. The study shows that alkaline pulping of pulpwood and bagasse improves its ability towards adsorption of the radiation degraded pesticide molecules

  20. Potassium hydroxide pulping of rice straw in biorefinery initiatives.

    Science.gov (United States)

    Jahan, M Sarwar; Haris, Fahmida; Rahman, M Mostafizur; Samaddar, Purabi Rani; Sutradhar, Shrikanta

    2016-11-01

    Rice straw is supposed to be one of the most important lignocellulosic raw materials for pulp mill in Asian countries. The major problem in rice straw pulping is silica. The present research is focused on the separation of silica from the black liquor of rice straw pulping by potassium hydroxide (KOH) and pulp evaluation. Optimum KOH pulping conditions of rice straw were alkali charge 12% as NaOH, cooking temperature 150°C for 2h and material to liquor ratio, 1:6. At this condition pulp yield was 42.4% with kappa number 10.3. KOH pulp bleached to 85% brightness by D0EpD1 bleaching sequences with ClO2 consumption of 25kg/ton of pulp. Silica and lignin were separated from the black liquor of KOH pulping. The amount of recovered silica, lignin and hemicelluloses were 10.4%, 8.4% and 13.0%. The papermaking properties of KOH pulp from rice straw were slightly better than those of corresponding NaOH pulp. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Pulp stem cells: implication in reparative dentin formation.

    Science.gov (United States)

    Dimitrova-Nakov, Sasha; Baudry, Anne; Harichane, Yassine; Kellermann, Odile; Goldberg, Michel

    2014-04-01

    Many dental pulp stem cells are neural crest derivatives essential for lifelong maintenance of tooth functions and homeostasis as well as tooth repair. These cells may be directly implicated in the healing process or indirectly involved in cell-to-cell diffusion of paracrine messages to resident (pulpoblasts) or nonresident cells (migrating mesenchymal cells). The identity of the pulp progenitors and the mechanisms sustaining their regenerative capacity remain largely unknown. Taking advantage of the A4 cell line, a multipotent stem cell derived from the molar pulp of mouse embryo, we investigated the capacity of these pulp-derived precursors to induce in vivo the formation of a reparative dentin-like structure upon implantation within the pulp of a rodent incisor or a first maxillary molar after surgical exposure. One month after the pulp injury alone, a nonmineralized fibrous matrix filled the mesial part of the coronal pulp chamber. Upon A4 cell implantation, a mineralized osteodentin was formed in the implantation site without affecting the structure and vitality of the residual pulp in the central and distal parts of the pulp chamber. These results show that dental pulp stem cells can induce the formation of reparative dentin and therefore constitute a useful tool for pulp therapies. Finally, reparative dentin was also built up when A4 progenitors were performed by alginate beads, suggesting that alginate is a suitable carrier for cell implantation in teeth. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  2. Adhesion to pulp chamber dentin: Effect of ethanol-wet bonding technique and proanthocyanidins application

    Directory of Open Access Journals (Sweden)

    Pallavi Sharma

    2015-01-01

    Full Text Available Aim: To evaluate the microleakage of a simplified etch-and-rinse adhesive bonded to pulp chamber dentin with water-wet bonding (WWB or ethanol-wet bonding (EWB with and without proanthocyanidins (PA application. Materials and Methods: Total 88 non-carious extracted human molar teeth were sectioned horizontally to expose the pulp chambers 1.5 mm coronal to the cemento-enamel junction. After the pulp tissue extirpation, canal orifices were enlarged and the root ends were sealed. The samples were randomly divided equally into following four groups according to the four bonding techniques performed using Adper Single Bond 2 [SB] adhesive (1 WWB; (2 EWB; (3 WWB and PA application [WWB + PA]; (4 EWB and PA application [EWB + PA]. Composite resin restorations were performed in all the pulp chambers. Total 20 samples from each group were subjected to microleakage evaluation, and two samples per group were assessed under scanning electron microscope for interfacial micromorphology. Results: The least microleakage score was observed in group 2 (EWB with similar results seen in group 4 (EWB + PA (P = 0.918. Group 2 (EWB showed significantly less microleakage than group 1 (WWB; P = 0.002 and group 3 (WWB + PA; P = 0.009. Group 4 (EWB + PA also depicted significantly reduced microleakage as compared with group 1 (WWB; P = 0.001 and group 3 (WWB + PA; P = 0.003. Conclusion: The use of EWB technique in a clinically relevant simplified dehydration protocol significantly reduced microleakage in simplified etch-and-rinse adhesive, Adper Single Bond 2, bonded to pulp chamber dentin. Application of PA had no significant effect on the microleakage of the adhesive bonded with either WWB or EWB.

  3. High levels of hydrogen peroxide in overnight tooth-whitening formulas: effects on enamel and pulp.

    Science.gov (United States)

    Pugh, George; Zaidel, Lynette; Lin, Nora; Stranick, Michael; Bagley, Daniel

    2005-01-01

    Limited data are available to assess the safety of high levels of hydrogen peroxide in overnight tooth-whitening formulas. The purpose of this study was to assess the effects of hydrogen peroxide on enamel microhardness, pulp penetration, and enamel morphology. Colgate Platinum Professional Overnight Whitening System (Colgate Oral Pharmaceuticals, Inc., Canton, MA, USA) (10% carbamide peroxide, equivalent to 3.5% hydrogen peroxide) was compared with two prototype formulations containing either 7.0% or 12.0% hydrogen peroxide. In the pulp chamber studies, human extracted teeth were exposed to 3.5%, 7.0%, or 12.0% hydrogen peroxide for 30 minutes, 4 hours, or 7 hours. Microhardness, electron spectroscopy for chemical analysis, and atomic force microscopy evaluations were made from enamel blocks cut from human extracted molars. The enamel blocks were evaluated following 14 7-hour treatments (98 h total). At 7 hours' post-treatment, hydrogen peroxide penetrated the pulp chamber at 23.12 +/- 10.09, 24.58 +/- 6.90, and 26.39 +/- 5.43 microg for 3.5%, 7.0%, and 12.0% hydrogen peroxide, respectively. With regard to enamel morphology, pulp penetration, microhardness, and elemental composition, no statistically significant differences were observed between treatment groups following 98 hours of treatment. Hydrogen peroxide does not adversely affect enamel morphology or microhardness. The levels recovered in pulp indicate that hydrogen peroxide is not expected to inhibit pulpal enzymes. Overnight tray products containing levels of hydrogen peroxide of 3.5%, 7.0%, and 12.0% are not expected to adversely affect the enamel or pulpal enzymes. Additional safety studies are needed to assess the potential for tooth sensitivity and gingival irritation.

  4. Characterization and Degradation of Pectic Polysaccharides in Cocoa Pulp.

    Science.gov (United States)

    Meersman, Esther; Struyf, Nore; Kyomugasho, Clare; Jamsazzadeh Kermani, Zahra; Santiago, Jihan Santanina; Baert, Eline; Hemdane, Sami; Vrancken, Gino; Verstrepen, Kevin J; Courtin, Christophe M; Hendrickx, Marc; Steensels, Jan

    2017-11-08

    Microbial fermentation of the viscous pulp surrounding cocoa beans is a crucial step in chocolate production. During this process, the pulp is degraded, after which the beans are dried and shipped to factories for further processing. Despite its central role in chocolate production, pulp degradation, which is assumed to be a result of pectin breakdown, has not been thoroughly investigated. Therefore, this study provides a comprehensive physicochemical analysis of cocoa pulp, focusing on pectic polysaccharides, and the factors influencing its degradation. Detailed analysis reveals that pectin in cocoa pulp largely consists of weakly bound substances, and that both temperature and enzyme activity play a role in its degradation. Furthermore, this study shows that pulp degradation by an indigenous yeast fully relies on the presence of a single gene (PGU1), encoding for an endopolygalacturonase. Apart from their basic scientific value, these new insights could propel the selection of microbial starter cultures for more efficient pulp degradation.

  5. Nanofibrillated cellulose as paper additive in Eucalyptus pulps

    Directory of Open Access Journals (Sweden)

    Israel González

    2012-11-01

    Full Text Available In this work, the physical and mechanical properties of bleached Eucalyptus pulp reinforced with nanofibrillated cellulose (NFC are compared with those of traditional beaten pulp used in the making of writing/printing and offset printing papers. For this purpose, three different types of hardwood slurries were prepared: beaten pulps, unbeaten pulps reinforced with NFC, and slightly beaten pulps also reinforced with NFC. Physical and mechanical tests were performed on handsheets from these different slurries. The results showed that adding NFC to unbeaten pulps results in physical and mechanical properties similar to those in pulps used for printing/writing papers. Nevertheless, the best results were obtained in slurries previously beaten at slight conditions and subsequently reinforced with NFC. These results demonstrate that the addition of NFC allows a reduction in beating intensity without decreasing the desired mechanical properties for this specific purpose.

  6. TESTING OF PULP VITALITY BY PULSOXIMETRY

    Directory of Open Access Journals (Sweden)

    Gabriela CIOBANU

    2012-06-01

    Full Text Available The methods applied for diagnosing the health condition of the pulp tissue are numerous, however, nowadays, an increasingly higher number of conventional tests are replaced by some objective, non-invasive, painless and reliable tests. Among them, pulse oximetry is a method for the investigation of pulp vitality based on oxygen saturation (SaO2 of the hemoglobin from the blood present in the pulp vascular bed, as a means of differentiating among the vital and the non-vital teeth. In the present study, registrations were made on a group of 120 frontal maxillary teeth, in patients with ages between 20 and 40 years, on using a digital sensor modified by the pulse oximeter with which the pulse and the values of oxygen saturation were measured at the level of both teeth and right hand finger. The mean SaO2 value in the pulp blood of the vital teeth was of 83.30% for the central incisor, of 78.51% for the lateral one and of 84.56%, respectively, for the canine; the value recorded at finger level was of 97%. In the non-vital teeth, the SaO2 value measured on the pulse oximeter was of 0%. Pulse registration showed mean values of 70.56 beatings/min at tooth level and of 70.88 beatings/min, respectively, at finger level. The results of the present study may confirm that pulse oximetry represents a simple, non-traumatic, efficient and objective method for testing the vitality condition of the dental pulp.

  7. Contribution of Histidine and Lysine to the Generation of Volatile Compounds in Jinhua Ham Exposed to Ripening Conditions Via Maillard Reaction.

    Science.gov (United States)

    Zhu, Chao-Zhi; Zhao, Jing-Li; Tian, Wei; Liu, Yan-Xia; Li, Miao-Yun; Zhao, Gai-Ming

    2018-01-01

    To evaluate the role of Maillard reactions in the generation of flavor compounds in Jinhua ham, the reactions of glucose and ethanal with histidine and lysine, respectively, were studied by simulating the ripening conditions of Jinhua ham. The volatile products produced were analyzed using solid phase microextraction-gas chromatography/mass spectrometry. The results showed that 8 volatile compounds were generated by the reaction of glucose and histidine and 10 volatile compounds were generated by the reaction of glucose and lysine. Reactions of ethanal with lysine and with histidine both generated 31 volatile compounds that contributed to the flavor of Jinhua ham. This indicates that histidine and lysine related to Maillard reactions possibly play important roles in the generation of the unique flavor compounds in Jinhua ham. This research demonstrates that free amino acids participate in the generation of volatile compounds from Jinhua ham via the Maillard reaction and provides a basic mechanism to explain flavor formation in Jinhua ham. Jinhua ham is a well-known traditional Chinese dry-cured meat product. However, the formation of the compounds comprising its special flavor is not well understood. Our results indicate that Maillard reactions occur in Jinhua ham under ripening conditions. This work illustrates the contribution of Maillard reactions to the flavor of Jinhua ham. © 2017 Institute of Food Technologists®.

  8. Nutritional variation in baobab (Adansonia digitata L.) fruit pulp and seeds based on Africa geographical regions.

    Science.gov (United States)

    Muthai, Kinuthia U; Karori, Mbuthia S; Muchugi, Alice; Indieka, Abwao S; Dembele, Catherine; Mng'omba, Simon; Jamnadass, Ramni

    2017-11-01

    Baobab ( Adansonia digitata L.) is an indigenous fruit tree associated with the Savannah drylands of sub-Saharan Africa. Local communities mainly utilize the leaves, pulp, and seeds of baobab as a source of food and for income generation. The present study was conducted to determine the nutritive attributes of baobab fruit pulp and seeds across provenances in east, west, and southern Africa and to determine whether the nutrient content varied with the provenance of origin. Pulp and seed proximate composition and mineral element concentration were determined using the AOAC 1984 methods and inductively coupled plasma atomic emission spectroscopy (ICP-AES), respectively. The results showed that there exist significant variation ( p  < .05) in pulp moisture, protein, fiber, ash, and elemental content among provenances. The highest mean pulp crude fiber (8.68 g 100 g -1 dw) was recorded in Kenya. At country level, Malawi had the highest mean pulp potassium (22.2 mg g -1 ), calcium (4,300 mg kg -1 ), magnesium (2,300 mg kg -1 ), sodium (1,000 mg kg -1 ), and phosphorus (1,100 mg kg -1 ) levels. Kenya had the highest mean pulp iron (57.4 μg g -1 ) and manganese (27.2 μg g -1 ) content, while Mali had the lowest iron (13.1 μg g -1 ) and manganese (8.6 μg g -1 ). At country level, the mean seed calcium content was highest (3,200 mg kg -1 ) in Malawi and lowest (2,000 mg kg -1 ) in Kenya. The highest mean iron content of 63.7 μg g -1 was recorded in seeds from Kenya, while the lowest (25.8 μg g -1 ) was in Mali. Baobab seed mineral and proximate content varied significantly ( p  < .001) among the selected countries. Overall, baobab fruit pulp and seeds contain significant amounts of nutritionally essential minerals and proximate components but the amounts varied significantly among the selected countries. This variation offers opportunities for selecting provenances to concentrate on during germplasm collection for conservation and

  9. Human dental pulp stem cells with highly angiogenic and neurogenic potential for possible use in pulp regeneration.

    Science.gov (United States)

    Nakashima, Misako; Iohara, Koichiro; Sugiyama, Masahiko

    2009-01-01

    Dental caries is a common public health problem, causing early loss of dental pulp and resultant tooth loss. Dental pulp has important functions to sustain teeth providing nutrient and oxygen supply, innervation, reactionary/reparative dentin formation and immune response. Regeneration of pulp is an unmet need in endodontic therapy, and angiogenesis/vasculogenesis and neurogenesis are critical for pulp regeneration. Permanent and deciduous pulp tissue is easily available from teeth after extraction without ethical issues and has potential for clinical use. In this review, we introduce some stem cell subfractions, CD31(-)/CD146(-) SP cells and CD105(+) cells with high angiogenic and neurogenic potential, derived from human adult dental pulp tissue. Potential utility of these cells is addressed as a source of cells for treatment of cerebral and limb ischemia and pulp inflammation complete with angiogenesis and vasculogenesis.

  10. BACTERIAL PROFILE OF NECROTIC PULPS IN CHEETAH (ACINONYX JUBATUS) CANINE TEETH.

    Science.gov (United States)

    Almansa Ruiz, José C; Bosman, Anna-Mari; Steenkamp, Gerhard

    2016-03-01

    The role of microbes and their antimicrobial susceptibilities in both acute and chronic infections of the dental pulp in humans has been well studied. Presently, no data are available on endodontic pathogens in cheetahs (Acinonyx jubatus). The aim of this study was to isolate and identify the bacteria found in the canine teeth of cheetahs, where the pulp was necrotic and exposed due to a complicated crown fracture. Thirty-six microbiologic samples were taken from root canals (RCs) of the canine teeth of 19 cheetahs: one pulp sample was taken from 10 cheetahs, four samples from 2 cheetahs, two samples from 3 cheetahs, and three samples from 4 cheetahs. Exposed pulps were cultured for aerobic and anaerobic bacteria; an additional screening with a 16S rRNA-specific polymerase chain reaction (PCR) was used for the last six samples. Antimicrobial susceptibility of isolates was determined by use of the Kirby-Bauer diffusion test. In total, 59 cultivable isolates belonging to 19 microbial species and 13 genera were recovered from the 36 RCs sampled. Only two samples yielded no cultivable bacteria. Thirty-two (54.49%) of the cultivable isolates were Gram positive and 27 (45.71%) were Gram negative. The maximum number of isolates cultivated from an individual RC was six. Facultative anaerobes (62.72%) were the most common bacteria of the RCs that yielded cultivable bacteria. Of the isolates, 28.81% were aerobic and 8.47% were strict anaerobes. The antimicrobials that showed the greatest efficacy in vitro against the different bacteria isolates were amikacin and gentamicin. The more common bacterial species isolated by PCR were anaerobes (60.8%), facultative anaerobes (30.2%), and aerobes (8.6%).

  11. Integration of the Mini-Sulfide Sulfite Anthraquinone (MSS-AQ) Pulping Process and Black Liquor Gasification in a Pulp Mill

    Energy Technology Data Exchange (ETDEWEB)

    Hasan Jameel, North Carolina State University; Adrianna Kirkman, North Carolina State University; Ravi Chandran,Thermochem Recovery International Brian Turk Research Triangle Institute; Brian Green, Research Triangle Institute

    2010-01-27

    As many of the recovery boilers and other pieces of large capital equipment of U.S. pulp mills are nearing the end of their useful life, the pulp and paper industry will soon need to make long-term investments in new technologies. The ability to install integrated, complete systems that are highly efficient will impact the industry’s energy use for decades to come. Developing a process for these new systems is key to the adoption of state-of-the-art technologies in the Forest Products industry. This project defined an integrated process model that combines mini-sulfide sulfite anthraquinone (MSS-AQ) pulping and black liquor gasification with a proprietary desulfurization process developed by the Research Triangle Institute. Black liquor gasification is an emerging technology that enables the use of MSS-AQ pulping, which results in higher yield, lower bleaching cost, lower sulfur emissions, and the elimination of causticization requirements. The recently developed gas cleanup/absorber technology can clean the product gas to a state suitable for use in a gas turbine and also regenerate the pulping chemicals needed to for the MSS-AQ pulping process. The combination of three advanced technologies into an integrated design will enable the pulping industry to achieve a new level of efficiency, environmental performance, and cost savings. Because the three technologies are complimentary, their adoption as a streamlined package will ensure their ability to deliver maximum energy and cost savings benefits. The process models developed by this project will enable the successful integration of new technologies into the next generation of chemical pulping mills. When compared to the Kraft reference pulp, the MSS-AQ procedures produced pulps with a 10-15 % yield benefit and the ISO brightness was 1.5-2 times greater. The pulp refined little easier and had a slightly lower apparent sheet density (In both the cases). At similar levels of tear index the MSS-AQ pulps also

  12. Viscoelastic Properties of Dental Pulp Tissue and Ramifications on Biomaterial Development for Pulp Regeneration.

    Science.gov (United States)

    Erisken, Cevat; Kalyon, Dilhan M; Zhou, Jian; Kim, Sahng G; Mao, Jeremy J

    2015-10-01

    A critical step in biomaterial selection effort is the determination of material as well as the biological properties of the target tissue. Previously, the selection of biomaterials and carriers for dental pulp regeneration has been solely based on empirical experience. In this study, first, the linear viscoelastic material functions and compressive properties of miniature pig dental pulp were characterized using small-amplitude oscillatory shear and uniaxial compression at a constant rate. They were then compared with the properties of hydrogels (ie, agarose, alginate, and collagen) that are widely used in tissue regeneration. The comparisons of the linear viscoelastic material functions of the native pulp tissue with those of the 3 hydrogels revealed the gel-like behavior of the pulp tissue over a relatively large range of time scales (ie, over the frequency range of 0.1-100 rps). At the constant gelation agent concentration of 2%, the dynamic properties (ie, storage and loss moduli and the tanδ) of the collagen-based gel approached those of the native tissue. Under uniaxial compression, the peak normal stresses and compressive moduli of the agarose gel were similar to those of the native tissue, whereas alginate and collagen exhibited significantly lower compressive properties. The linear viscoelastic and uniaxial compressive properties of the dental pulp tissue reported here should enable the more appropriate selection of biogels for dental pulp regeneration via the better tailoring of gelation agents and their concentrations to better mimic the dynamic and compressive properties of native pulp tissue. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  13. Immunolocalization of bone-resorptive cytokines in rat pulp and periapical lesions following surgical pulp exposure.

    Science.gov (United States)

    Tani-Ishii, N; Wang, C Y; Stashenko, P

    1995-08-01

    The bone-resorptive cytokines interleukin 1 (IL-1) and tumor necrosis factor (TNF) have been implicated in the pathogenesis of many chronic inflammatory diseases, including pulpitis and apical periodontitis.To further elucidate their role in these disorders, we have identified cells that express IL-1 alpha and TNF alpha in infected pulps and in developing rat periapical lesions after surgical pulp exposure. As detected by immunohistochemistry, IL-1 alpha- and TNF alpha-positive cells were present as early as 2 days after pulp exposure in both the pulp and periapical region. The numbers of cytokine-expressing cells increased up to day 4 in the pulp and up to day 30 in the periapex. In contrast, cells expressing IL-1 beta and TNF beta, the homologous forms of these mediators, were not found in pulp or periapical lesions during this period. Cells expressing IL-1 alpha and TNF alpha were identified primarily as macrophages and fibroblasts, with occasional staining of polymorphonuclear leukocytes. Osteoblasts and osteoclasts were also positive, whereas lymphocytes were negative. In general, cytokine-expressing cells were located proximal to abscesses and the root apex. These findings demonstrate that cells that express bone-resorptive cytokines IL-1 alpha and TNF alpha are present immediately after pulp exposure in this model, which supports the hypothesis that these mediators play a key role in pulpal and periapical pathogenesis, including the concomitant bone destruction. They also indicate that both resident connective tissue cells as well as infiltrating cells express bone-resorptive cytokines in response to infection in these lesions.

  14. Durability of pulp fiber-cement composites

    Science.gov (United States)

    Mohr, Benjamin J.

    Wood pulp fibers are a unique reinforcing material as they are non-hazardous, renewable, and readily available at relatively low cost compared to other commercially available fibers. Today, pulp fiber-cement composites can be found in products such as extruded non-pressure pipes and non-structural building materials, mainly thin-sheet products. Although natural fibers have been used historically to reinforce various building materials, little scientific effort has been devoted to the examination of natural fibers to reinforce engineering materials until recently. The need for this type of fundamental research has been emphasized by widespread awareness of moisture-related failures of some engineered materials; these failures have led to the filing of national- and state-level class action lawsuits against several manufacturers. Thus, if pulp fiber-cement composites are to be used for exterior structural applications, the effects of cyclical wet/dry (rain/heat) exposure on performance must be known. Pulp fiber-cement composites have been tested in flexure to examine the progression of strength and toughness degradation. Based on scanning electron microscopy (SEM), environmental scanning electron microscopy (ESEM), energy dispersive spectroscopy (EDS), a three-part model describing the mechanisms of progressive degradation has been proposed: (1) initial fiber-cement/fiber interlayer debonding, (2) reprecipitation of crystalline and amorphous ettringite within the void space at the former fiber-cement interface, and (3) fiber embrittlement due to reprecipitation of calcium hydroxide filling the spaces within the fiber cell wall structure. Finally, as a means to mitigate kraft pulp fiber-cement composite degradation, the effects of partial portland cement replacement with various supplementary cementitious materials (SCMs) has been investigated for their effect on mitigating kraft pulp fiber-cement composite mechanical property degradation (i.e., strength and toughness

  15. Evaluation of bleachability on pine and eucalyptus kraft pulps

    Directory of Open Access Journals (Sweden)

    Marcela Freitas Andrade

    2013-09-01

    Full Text Available In recent decades, the pulp industry has been changing and improving its manufacturing processes in order to enhance production capacity, product quality and environmental performance. The aim of this study was to evaluate the bleachability effect on the efficient washing and alkaline leaching in eucalyptus and pine Kraft pulps using three different bleaching sequences: AD(EPD, A/D(EPDP and DHT(EPDP. This study was carried out in two stages. In the first part, the optimum conditions for pulp bleaching in order to achieve a brightness of 90% ISO were established. The second step was a comparative study between the pulps that received alkaline leaching and efficient washing with reference pulp (without treatment. The brightness, viscosity, kappa number and HexA in pulp were analyzed. The three sequences studied reached the desired brightness, but the sequence AD(EPD produced a lower reagent consumption for the same brightness. In the three sequences studied, the efficient washing of the pulp after oxygen delignification has contributed significantly to the removal of dissolved organic and inorganic materials in the pulp and the alkaline leaching decreased significantly the pulp kappa number due to a higher pulp delignification and bleachability.

  16. Evaluating pulp stiffness from fibre bundles by ultrasound

    Science.gov (United States)

    Karppinen, Timo; Montonen, Risto; Määttänen, Marjo; Ekman, Axel; Myllys, Markko; Timonen, Jussi; Hæggström, Edward

    2012-06-01

    A non-destructive ultrasonic tester was developed to measure the stiffness of pulp bundles. The mechanical properties of pulp are important when estimating the behaviour of paper under stress. Currently available pulp tests are tedious and alter the fibres structurally and mechanically. The developed tester employs (933 ± 15) kHz tweezer-like ultrasonic transducers and time-of-flight measurement through (9.0 ± 2.5) mm long and (0.8 ± 0.1) mm thick fibre bundles kept at (19.1 ± 0.4) °C and (62 ± 1)% RH. We determined the stiffness of soft wood pulps produced by three kraft pulping modifications: standard kraft pulp, (5.2 ± 0.4) GPa, prehydrolysis kraft pulp, (4.3 ± 0.4) GPa, and alkali extracted prehydrolysis kraft pulp, (3.3 ± 0.4) GPa. Prehydrolysis and alkali extraction processes mainly lowered the hemicellulose content of the pulps, which essentially decreased the fibre-wall stiffness hence impairing the stiffness of the fibre networks. Our results indicate that the method allows ranking of pulps according to their stiffness determined from bundle-like samples taken at an early phase of the papermaking process.

  17. Performance of Schizolobium amazonicum Wood in Bleached Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    Camila Sarto

    2015-05-01

    Full Text Available This study aimed to evaluate the characteristics of Schizolobium amazonicum wood, specifically its performance in bleached kraft pulp production and the characteristics of its pulp. Chips of Schizolobium amazonicum and Eucalyptus grandis x Eucalyptus urophylla (reference were used. The following parameters were evaluated in the wood: basic density, total extractives, total lignin, holocellulose, and fiber morphology. The pulping simulations were carried out in a laboratory digester, with parameters set to obtain pulp with kappa number 19 ± 0.5. Both pulps were bleached in a PFI mill and submitted to physical-mechanical tests. The results showed that S. amazonicum wood has low basic density and higher content of extractives when compared to E. grandis x E. urophylla wood. For pulping, S. amazonicum required higher alkali charge and H factor to achieve the same delignification level of E. grandis x E. urophylla, resulting in a lower yield, pulp with lower viscosity, and higher wood specific consumption. During bleaching, the brightness gain and final viscosity of S. amazonicum pulp were lower than E. grandis x E. urophylla pulp. Moreover, S. amazonicum pulp had worse physical-mechanical characteristics than E. grandis x E. urophylla.

  18. Pulp and paper from blue agave waste from tequila production.

    Science.gov (United States)

    Idarraga, G; Ramos, J; Zuñiga, V; Sahin, T; Young, R A

    1999-10-01

    Pulping of blue agave waste, from the production of tequila, was evaluated by both chemical and biomechanical pulping processes. Two conventional and two organosolv systems were used to pulp the agave waste under a standard set of conditions. The soda-ethanol process was superior in terms of delignification and pulp properties in comparison to the soda and ethanol organosolv processes for pulping of agave waste; however, the kraft process gave the best strength properties. In general, the strength of the agave waste pulps was rather poor in comparison to wood and other agro-based pulps; however, the tear strength was relatively high. This result is typical of poorly bonded sheets and may be due to the coarseness of the agave fibers and/or loss of hemicelluloses in the steaming process for the tequila production. Fungal treatment of the agave waste with Ceriporiopsis subvermispora reduced the energy consumption for mechanical refining but gave biomechanical pulps with inferior strength properties. The blue agave chemical pulps should be suitable for blending with softwood kraft pulps for publication grade paper.

  19. Simultaneous Saccharification and Fermentation of Sugar Beet Pulp for Efficient Bioethanol Production

    Science.gov (United States)

    Berłowska, Joanna; Balcerek, Maria; Dziekońska-Kubczak, Urszula; Patelski, Piotr; Dziugan, Piotr

    2016-01-01

    Sugar beet pulp, a byproduct of sugar beet processing, can be used as a feedstock in second-generation ethanol production. The objective of this study was to investigate the effects of pretreatment, of the dosage of cellulase and hemicellulase enzyme preparations used, and of aeration on the release of fermentable sugars and ethanol yield during simultaneous saccharification and fermentation (SSF) of sugar beet pulp-based worts. Pressure-thermal pretreatment was applied to sugar beet pulp suspended in 2% w/w sulphuric acid solution at a ratio providing 12% dry matter. Enzymatic hydrolysis was conducted using Viscozyme and Ultraflo Max (Novozymes) enzyme preparations (0.015–0.02 mL/g dry matter). Two yeast strains were used for fermentation: Ethanol Red (S. cerevisiae) (1 g/L) and Pichia stipitis (0.5 g/L), applied sequentially. The results show that efficient simultaneous saccharification and fermentation of sugar beet pulp was achieved. A 6 h interval for enzymatic activation between the application of enzyme preparations and inoculation with Ethanol Red further improved the fermentation performance, with the highest ethanol concentration reaching 26.9 ± 1.2 g/L and 86.5 ± 2.1% fermentation efficiency relative to the theoretical yield. PMID:27722169

  20. Integrated Bioethanol Fermentation/Anaerobic Digestion for Valorization of Sugar Beet Pulp

    Directory of Open Access Journals (Sweden)

    Joanna Berlowska

    2017-08-01

    Full Text Available Large amounts of waste biomass are generated in sugar factories from the processing of sugar beets. After diffusion with hot water to draw the sugar from the beet pieces, a wet material remains called pulp. In this study, waste sugar beet pulp biomass was enzymatically depolymerized, and the obtained hydrolyzates were subjected to fermentation processes. Bioethanol, biomethane, and biohydrogen were produced directly from the substrate or in combined mode. Stillage, a distillery by-product, was used as a feedstock for anaerobic digestion. During biosynthesis of ethanol, most of the carbohydrates released from the sugar beet pulp were utilized by a co-culture of Saccharomyces cerevisiae Ethanol Red, and Scheffersomyces stipitis LOCK0047 giving 12.6 g/L of ethanol. Stillage containing unfermented sugars (mainly arabinose, galactose and raffinose was found to be a good substrate for methane production (444 dm3 CH4/kg volatile solids (VS. Better results were achieved with this medium than with enzymatic saccharified biomass. Thermal pre-treatment and adjusting the pH of the inoculum resulted in higher hydrogen production. The largest (p < 0.05 hydrogen yield (252 dm3 H2/kg VS was achieved with sugar beet stillage (SBS. In contrast, without pre-treatment the same medium yielded 35 dm3 H2/kg VS. However, dark fermentation of biohydrogen was more efficient when sugar beet pulp hydrolyzate was used.

  1. Simultaneous Saccharification and Fermentation of Sugar Beet Pulp for Efficient Bioethanol Production.

    Science.gov (United States)

    Berłowska, Joanna; Pielech-Przybylska, Katarzyna; Balcerek, Maria; Dziekońska-Kubczak, Urszula; Patelski, Piotr; Dziugan, Piotr; Kręgiel, Dorota

    2016-01-01

    Sugar beet pulp, a byproduct of sugar beet processing, can be used as a feedstock in second-generation ethanol production. The objective of this study was to investigate the effects of pretreatment, of the dosage of cellulase and hemicellulase enzyme preparations used, and of aeration on the release of fermentable sugars and ethanol yield during simultaneous saccharification and fermentation (SSF) of sugar beet pulp-based worts. Pressure-thermal pretreatment was applied to sugar beet pulp suspended in 2% w/w sulphuric acid solution at a ratio providing 12% dry matter. Enzymatic hydrolysis was conducted using Viscozyme and Ultraflo Max (Novozymes) enzyme preparations (0.015-0.02 mL/g dry matter). Two yeast strains were used for fermentation: Ethanol Red ( S. cerevisiae ) (1 g/L) and Pichia stipitis (0.5 g/L), applied sequentially. The results show that efficient simultaneous saccharification and fermentation of sugar beet pulp was achieved. A 6 h interval for enzymatic activation between the application of enzyme preparations and inoculation with Ethanol Red further improved the fermentation performance, with the highest ethanol concentration reaching 26.9 ± 1.2 g/L and 86.5 ± 2.1% fermentation efficiency relative to the theoretical yield.

  2. Activated carbon prepared from coffee pulp: potential adsorbent of organic contaminants in aqueous solution.

    Science.gov (United States)

    Gonçalves, Maraisa; Guerreiro, Mário César; Ramos, Paulize Honorato; de Oliveira, Luiz Carlos Alves; Sapag, Karim

    2013-01-01

    The processing of coffee beans generates large amounts of solid and liquid residues. The solid residues (pulp, husk and parchment) represent a serious environmental problem and do not have an adequate disposal mechanism. In this work, activated carbons (ACs) for adsorption of organic compounds were prepared from coffee pulp by controlled temperature at different pulp/Na2HPO4 ratios (4:1, 2:1, 5:4 and 1:1). The N2 adsorption/desorption isotherms showed ACs with high quantities of mesopores and micropores and specific surface areas of 140, 150, 450 and 440 m(2)g(-1) for AC 4:1, AC 2:1, AC 5:4 and AC 1:1, respectively. The prepared material AC 5:4 showed a higher removal capacity of the organic contaminants methylene blue (MB), direct red (DR) and phenol than did a Merck AC. The maximum capacities for this AC are approximately 150, 120 and 120 mg g(-1) for MB, DR and phenol, respectively. Thus, a good adsorbent was obtained from coffee pulp, an abundant Brazilian residue.

  3. Transcriptomic analysis reveals key genes related to betalain biosynthesis in pulp coloration of Hylocereus polyrhizus

    Directory of Open Access Journals (Sweden)

    Hua eQingzhu

    2016-01-01

    Full Text Available Betalains have high nutritional value and bioactivities. Red pulp pitaya (Hylocereus polyrhizus is the only fruit containing abundant betalains for consumer. However, no information is available about genes involved in betalain biosynthesis in H. polyrhizus. Herein, two cDNA libraries of pitaya pulps with two different coloration stages (white and red pulp stages of Guanhuahong (H. polyrhizus were constructed. A total of about 12 Gb raw RNA-Seq data was generated and was de novo assembled into 122,677 transcripts with an average length of 1,183 bp and an N50 value of 2008. Approximately 99.99% of all transcripts were annotated based on seven public databases. A total of 8,871 transcripts were significantly regulated. Thirty-three candidate transcripts related to betalain biosynthesis were obtained from the transcriptome data. Transcripts encoding enzymes involved in betalain biosynthesis were analyzed using RT-qPCR at the whole pulp coloration stages of H. Polyrhizus (7-1 and H. Undatus (132-4. Nine key transcripts of betalain biosynthesis were identified. They were assigned to four kinds of genes in betalain biosynthetic pathway, including tyrosinase, 4, 5-DOPA dioxygenase extradiol, cytochrome P450 and glucosyltransferase. Ultimately, a preliminary betalain biosynthetic pathway for pitaya was proposed based on betalain analyses and gene expression profiles.

  4. Shift in aggregation, ROS generation, antioxidative defense, lysozyme and acetylcholinesterase activities in the cells of an Indian freshwater sponge exposed to washing soda (sodium carbonate).

    Science.gov (United States)

    Mukherjee, Soumalya; Ray, Mitali; Ray, Sajal

    2016-09-01

    Washing soda, chemically identified as anhydrous sodium carbonate, is a popular cleaning agent among the rural and urban populations of India which often contaminates the freshwater ponds and lakes, the natural habitat of sponge Eunapius carteri. Present investigation deals with estimation of cellular aggregation, generation of ROS and activities of antioxidant enzymes, lysozyme and acetylcholinesterase in the cells of E. carteri under the environmentally realistic concentrations of washing soda. Prolonged treatment of washing soda inhibited the degree of cellular aggregation. Experimental exposure of 8 and 16mg/l of sodium carbonate for 48h elevated the physiological level of reactive oxygen species (ROS) generation in the agranulocytes, semigranulocytes and granulocytes of E. carteri, whereas, treatment of 192h inhibited the ROS generation in three cellular morphotypes. Activities of superoxide dismutase, catalase and glutathione-S-transferase were recorded to be inhibited under prolonged exposure of washing soda. Washing soda mediated inhibition of ROS generation and depletion in the activities of antioxidant enzymes were indicative to an undesirable shift in cytotoxic status and antioxidative defense in E. carteri. Inhibition in the activity of lysozyme under the treatment of sodium carbonate was suggestive to a severe impairment of the innate immunological efficiency of E. carteri distributed in the washing soda contaminated habitat. Washing soda mediated inhibition in the activity of acetylcholinesterase indicated its neurotoxicity in E. carteri. Washing soda, a reported environmental contaminant, affected adversely the immunophysiological status of E. carteri with reference to cellular aggregation, oxidative stress, antioxidative defense, lysozyme and acetylcholinesterase activity. Copyright © 2016 Elsevier Inc. All rights reserved.

  5. Extended One-Generation Reproductive Toxicity Test in Rats Exposed to 3-Nitro-1,2,4 Triazol-5-One (NTO), October 2013-March 2014

    Science.gov (United States)

    2016-04-01

    Protection and Enhancement . http://www.apd.army.mil/pdffiles/r200_1.pdf. 2007. 3. DA, Regulation 40-5, Preventive Medicine. http://www.apd.army.mil...maturation. Any abnormalities of genital organs, such as persistent vaginal thread, hypospadia or cleft penis , will be noted. Body weight will be...consistency and precision is not greatly enhanced ” (ICH 2005). Examining all pups in each litter in the F1 generation will enhance the ability to detect effects

  6. Expression of high mobility group box 1 in inflamed dental pulp and its chemotactic effect on dental pulp cells

    International Nuclear Information System (INIS)

    Zhang, Xufang; Jiang, Hongwei; Gong, Qimei; Fan, Chen; Huang, Yihua; Ling, Junqi

    2014-01-01

    Highlights: • HMGB1 translocated from nucleus to cytoplasm during dental pulp inflammation. • HMGB1and its receptor RAGE were up-regulated in hDPCs under LPS stimulation. • HMGB1 enhanced hDPCs migration and induces cytoskeleton reorganization. • HMGB1 may play a critical role in dental pulp repair during inflamed state. - Abstract: High mobility group box 1 protein (HMGB1) is a chromatin protein which can be released extracellularly, eliciting a pro-inflammatory response and promoting tissue repair process. This study aimed to examine the expression and distribution of HMGB1 and its receptor RAGE in inflamed dental pulp tissues, and to assess its effects on proliferation, migration and cytoskeleton of cultured human dental pulp cells (DPCs). Our data demonstrated that cytoplasmic expression of HMGB1 was observed in inflamed pulp tissues, while HMGB1 expression was confined in the nuclei in healthy dental pulp. The mRNA expression of HMGB1 and RAGE were significantly increased in inflamed pulps. In in vitro cultured DPCs, expression of HMGB1 in both protein and mRNA level was up-regulated after treated with lipopolysaccharide (LPS). Exogenous HMGB1 enhanced DPCs migration in a dose-dependent manner and induced the reorganization of f-actin in DPCs. Our results suggests that HMGB1 are not only involved in the process of dental pulp inflammation, but also play an important role in the recruitment of dental pulp stem cells, promoting pulp repair and regeneration

  7. Expression of high mobility group box 1 in inflamed dental pulp and its chemotactic effect on dental pulp cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xufang, E-mail: xufang.zhang@student.qut.edu.au [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Institute of Health and Biomedical Innovation, Queensland University of Technology, Brisbane, QLD 4059 (Australia); Jiang, Hongwei, E-mail: jianghw@163.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Gong, Qimei, E-mail: gongqmei@gmail.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Fan, Chen, E-mail: c3.fan@student.qut.edu.au [Institute of Health and Biomedical Innovation, Queensland University of Technology, Brisbane, QLD 4059 (Australia); Huang, Yihua, E-mail: enu0701@163.com [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Ling, Junqi, E-mail: lingjq@mail.sysu.edu.cn [Department of Operative Dentistry and Endodontics, Guanghua School of Stomatology, Guangdong Province Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China)

    2014-08-08

    Highlights: • HMGB1 translocated from nucleus to cytoplasm during dental pulp inflammation. • HMGB1and its receptor RAGE were up-regulated in hDPCs under LPS stimulation. • HMGB1 enhanced hDPCs migration and induces cytoskeleton reorganization. • HMGB1 may play a critical role in dental pulp repair during inflamed state. - Abstract: High mobility group box 1 protein (HMGB1) is a chromatin protein which can be released extracellularly, eliciting a pro-inflammatory response and promoting tissue repair process. This study aimed to examine the expression and distribution of HMGB1 and its receptor RAGE in inflamed dental pulp tissues, and to assess its effects on proliferation, migration and cytoskeleton of cultured human dental pulp cells (DPCs). Our data demonstrated that cytoplasmic expression of HMGB1 was observed in inflamed pulp tissues, while HMGB1 expression was confined in the nuclei in healthy dental pulp. The mRNA expression of HMGB1 and RAGE were significantly increased in inflamed pulps. In in vitro cultured DPCs, expression of HMGB1 in both protein and mRNA level was up-regulated after treated with lipopolysaccharide (LPS). Exogenous HMGB1 enhanced DPCs migration in a dose-dependent manner and induced the reorganization of f-actin in DPCs. Our results suggests that HMGB1 are not only involved in the process of dental pulp inflammation, but also play an important role in the recruitment of dental pulp stem cells, promoting pulp repair and regeneration.

  8. Pembuatan Pulp dari Alang-alang

    OpenAIRE

    Ivan Wibisono Aylianawati

    2011-01-01

    Alang-alang merupakan tanaman gulma yang jumlahnya cukup besar di Indonesia. Hingga saat ini pemanfaatan dalam jumlah yang besar terhadap alang-alang di Indonesia belum ada. Alang-alang mempunyai kandungan selulosa yang cukup tinggi. Pada penelitian pendahuluan terhadap bahan baku alang-alang mengandung kadar alfa selulosa sekitar 41,7% dan mempunyai bilangan Kappa sebesar 37,1886. Maka alang-alang bisa dijadikan sebagai bahan dari pulp untuk pembuatan kertas. Tujuan penelitian ini adalah ...

  9. Potential for biohydrogen and methane production from olive pulp

    DEFF Research Database (Denmark)

    Gavala, Hariklia N.; Skiadas, Ioannis V.; Ahring, Birgitte Kiær

    2005-01-01

    The present study investigates the potential for thermophilic biohydrogen and methane production from olive pulp, which is the semi-solid residue coming from the two-phase processing of olives. It focussed on: a) production of methane from the raw olive pulp, b) anaerobic bio-production of hydrogen...... from the olive pulp, and c) subsequent anaerobic treatment of the hydrogen-effluent with the simultaneous production of methane. Both continuous and batch experiments were performed. The hydrogen potential of the olive pulp amounted to 1.6 mmole H-2 per g TS. The methane potential of the raw olive pulp...... and hydrogen-effluent was as high as 19 mmole CH4 per g TS. This suggests that olive pulp is an ideal substrate for methane production and it shows that biohydrogen production can be very efficiently coupled with a subsequent step for methane production....

  10. Dental Pulp Defence and Repair Mechanisms in Dental Caries

    OpenAIRE

    Farges, Jean-Christophe; Alliot-Licht, Brigitte; Renard, Emmanuelle; Ducret, Maxime; Gaudin, Alexis; Smith, Anthony J.; Cooper, Paul R.

    2015-01-01

    Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and red...

  11. Association between dental pulp stones and calcifying nanoparticles.

    Science.gov (United States)

    Zeng, Jinfeng; Yang, Fang; Zhang, Wei; Gong, Qimei; Du, Yu; Ling, Junqi

    2011-01-07

    The etiology of dental pulp stones, one type of extraskeletal calcification disease, remains elusive to date. Calcifying nanoparticles (CNPs), formerly referred to as nanobacteria, were reported to be one etiological factor in a number of extraskeletal calcification diseases. We hypothesized that CNPs are involved in the calcification of the dental pulp tissue, and therefore investigated the link between CNPs and dental pulp stones. Sixty-five freshly collected dental pulp stones, each from a different patient, were analyzed. Thirteen of the pulp stones were examined for the existence of CNPs in situ by immunohistochemical staining (IHS), indirect immunofluorescence staining (IIFS), and transmission electron microscope (TEM). The remaining 52 pulp stones were used for isolation and cultivation of CNPs; the cultured CNPs were identified and confirmed via their shape and growth characteristics. Among the dental pulp stones examined in situ, 84.6% of the tissue samples staines positive for CNPs antigen by IHS; the corresponding rate by IIFS was 92.3 %. In 88.2% of the cultured samples, CNPs were isolated and cultivated successfully. The CNPs were visible under TEM as 200-400 nm diameter spherical particles surrounded by a compact crust. CNPs could be detected and isolated from a high percentage of dental pulp stones, suggesting that CNPs might play an important role in the calcification of dental pulp.

  12. The caries process and its effect on the pulp

    DEFF Research Database (Denmark)

    Bjørndal, Lars

    2008-01-01

    The understanding of the caries process and its effect on the pulp is presented in the context that caries does develop in various rates of progression. Early in the caries process, the pulp reflects changes within lesion activity. Thus, the early pulp response is reversible. Later, the rate...... of caries progression is reflected by the quality of the tertiary dentin. Slowly progressing lesions create tertiary dentin resembling normal tubular dentin. Rapidly progressing lesions lead to the production of a tubular dentin or complete absence of tertiary dentin, as well as pulp necrosis and apical...

  13. A modified efficient method for dental pulp stem cell isolation.

    Science.gov (United States)

    Raoof, Maryam; Yaghoobi, Mohammad Mehdi; Derakhshani, Ali; Kamal-Abadi, Ali Mohammadi; Ebrahimi, Behnam; Abbasnejad, Mehdi; Shokouhinejad, Noushin

    2014-03-01

    Dental pulp stem cells can be used in regenerative endodontic therapy. The aim of this study was to introduce an efficient method for dental pulp stem cells isolation. In this in-vitro study, 60 extracted human third molars were split and pulp tissue was extracted. Dental pulp stem cells were isolated by the following three different methods: (1) digestion of pulp by collagenase/dispase enzyme and culture of the released cells; (2) outgrowth of the cells by culture of undigested pulp pieces; (3) digestion of pulp tissue pieces and fixing them. The cells were cultured in minimum essential medium alpha modification (αMEM) medium supplemented with 20% fetal bovine serum(FBS) in humid 37°C incubator with 5% CO 2. The markers of stem cells were studied by reverse transcriptase polymerase chain reaction (PCR). The student t-test was used for comparing the means of independent groups. P third method, we obtained stem cells successfully with about 60% efficiency after 2 days. The results of RT-PCR suggested the expression of Nanog, Oct-4, and Nucleostemin markers in the isolated cells from dental pulps. This study proposes a new method with high efficacy to obtain dental pulp stem cells in a short time.

  14. Method of increasing efficiency of uranium sorption from acid pulp

    International Nuclear Information System (INIS)

    Parobek, P.; Hinterholzinger, O.; Baloun, S.; Homolka, V.; Vanek, J.; Vebr, Z.

    1989-01-01

    Acid pulp containing uranium is adjusted to pH 2.5 to 4 with alkaline agents, such as alkaline pulp, lime milk, finely ground limestone or soda, or a combination thereof. The treated pulp is put into contact with an ion exchanger whose pH has been adjuste to a range of 2.5 to 4. Partial pulp neutralization causes the hydrolysis of the iron present and an overall reduction in salt contents and a significant increase in the ion exchanger sorptio capacity and thus the overall sorption efficiency. The quality o the eluate and of the uranium concentrate improves. (B.S.)

  15. Kinetic modeling of formic acid pulping of bagasse.

    Science.gov (United States)

    Tu, Qiliang; Fu, Shiyu; Zhan, Huaiyu; Chai, Xinsheng; Lucia, Lucian A

    2008-05-14

    Organic solvent or organosolv pulping processes are alternatives to soda or kraft pulping to delignify lignocellulosic materials for the production of paper pulp. Formic acid, a typical organosolv system, has been presently examined under atmospheric pressure to pulp bagasse fibers. It was shown that efficient bagasse pulping was achieved when the formic acid concentration was limited to 90% (v/v). A statistical kinetic model based on the experimental results for the delignification of bagasse during formic acid pulping was developed that can be described as follows: D (delignification) = 0.747 x C(formicacid) (1.688) x (1 - e(-0.05171t)), an equation that can be used to predict the lignin content in formic acid during the pulping process. The delignification of bagasse by 90% formic acid was almost completed after approximately 80 min, while extended pulping did not improve the delignification but tended to degrade the carbohydrates in bagasse, especially the hemicelluloses, which were rapidly hydrolyzed at the onset of pulping.

  16. Pulping and paper properties of Palmyra palm fruit fibers

    Directory of Open Access Journals (Sweden)

    Waranyou Sridach

    2010-05-01

    Full Text Available Palmyra palm fruit fibers have the properties to be used as an alternative raw material of cellulosic pulps for papermaking.Acid and alkali pulping were investigated by using nitric acid and caustic soda on a laboratory scale, with the purpose of producing printing or writing grade pulp. The chemical composition of fiber strands from palmyra palm fruits were examined, such as holocellulose, cellulose, pentosan, lignin and extractives. The yields of acid and soda pulps were below 40%. The main physical and mechanical properties of hand sheets produced from acid and soda processes were evaluated on 80 g/m2 test sheets as functions of the following parameters: tensile index, tear index, and brightness. The mechanical properties of soda pulps were developed by twin-roll press while it was not necessary to fibrillate acidic pulps through the beating step. The soda pulp sheets presented a lower brightness than that of acidic pulp sheets. The mechanicaland physical properties of the acidic and alkaline pulps verified that they were of an acceptable quality for papermaking.

  17. Proteomic analysis of human tooth pulp: proteomics of human tooth.

    Science.gov (United States)

    Eckhardt, Adam; Jágr, Michal; Pataridis, Statis; Mikšík, Ivan

    2014-12-01

    The unique pulp-dentin complex demonstrates strong regenerative potential, which enables it to respond to disease and traumatic injury. Identifying the proteins of the pulp-dentin complex is crucial to understanding the mechanisms of regeneration, tissue calcification, defense processes, and the reparation of dentin by dental pulp. The lack of knowledge of these proteins limits the development of more efficient therapies. The proteomic profile of human tooth pulp was investigated and compared with the proteome of human dentin and blood. The samples of tooth pulp were obtained from 5 sound permanent human third molars of 5 adults (n = 5). The extracted proteins were separated by 2-dimensional gel electrophoresis, analyzed by nano-liquid chromatography tandem mass spectrometry, and identified by correlating mass spectra to the proteomic databases. A total of 342 proteins were identified with high confidence, and 2 proteins were detected for the first time in an actual human sample. The identified tooth pulp proteins have a variety of functions: structural, catalytic, transporter, protease activity, immune response, and many others. In a comparison with dentin and blood plasma, 140 (pulp/dentin) shared proteins were identified, 37 of which were not observed in plasma. It can be suggested that they might participate in the unique pulp-dentin complex. This proteomic investigation of human tooth pulp, together with the previously published study of human dentin, is one of the most comprehensive proteome lists of human teeth to date. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  18. Improvement in rice straw pulp bleaching effluent quality by incorporating oxygen delignification stage prior to elemental chlorine-free bleaching.

    Science.gov (United States)

    Kaur, Daljeet; Bhardwaj, Nishi K; Lohchab, Rajesh Kumar

    2017-10-01

    Environmental degradation by industrial and other developmental activities is alarming for imperative environmental management by process advancements of production. Pulp and paper mills are now focusing on using nonwood-based raw materials to protect forest resources. In present study, rice straw was utilized for pulp production as it is easily and abundantly available as well as rich in carbohydrates (cellulose and hemicelluloses). Soda-anthraquinone method was used for pulp production as it is widely accepted for agro residues. Bleaching process during paper production is the chief source of wastewater generation. The chlorophenolic compounds generated during bleaching are highly toxic, mutagenic, and bioaccumulative in nature. The objectives of study were to use oxygen delignification (ODL) stage prior to elemental chlorine-free (ECF) bleaching to reduce wastewater load and to study its impact on bleached pulp characteristics. ODL stage prior to ECF bleaching improved the optical properties of pulp in comparison to only ECF bleaching. When ODL stage was incorporated prior to bleaching, the tensile index and folding endurance of the pulp were found to be 56.6 ± 1.5 Nm/g and 140, respectively, very high in comparison to ECF alone. A potential reduction of 51, 57, 43, and 53% in BOD 3 , COD, color, and AOX, respectively was observed on adding the ODL stage compared to ECF only. Generation of chlorophenolic compounds was reduced significantly. Incorporation of ODL stage prior to bleaching was found to be highly promising for reducing the toxicity of bleaching effluents and may lead to better management of nearby water resources. Graphical abstract ᅟ.

  19. Final Technical Report Steam Cycle Washer for Unbleached Pulp

    Energy Technology Data Exchange (ETDEWEB)

    Starkey, Yvonne; Salminen, Reijo; Karlsnes, Andy

    2008-09-22

    Project Abstract for “Steam Cycle Washer for Unbleached Pulp” When completed, the patented SC Washer will provide an innovative, energy efficient demonstration project to wash unbleached pulp using a pressure vessel charged with steam. The Port Townsend Paper Corporation’s pulp mill in Port Townsend, WA was initially selected as the host site for conducting the demonstration of the SCW. Due to 2006 and 2007 delays in the project caused by issues with 21st Century Pulp & Paper, the developer of the SCW, and the 2007 bankruptcy proceedings and subsequent restructuring at Port Townsend Paper, the mill can no longer serve as a host site. An alternate host site is now being sought to complete the commercial demonstration of the Steam Cycle Washer for Unbleached Pulp. Additionally, estimated costs to complete the project have more than doubled since the initial estimates for the project were completed in 2002. Additional grant funding from DOE was sought and in July, 2008 the additional DOE funds were procured under a new DOE award, DE-PS36-08GO98014 issued to INL. Once the new host site is secured the completion of the project will begin under the management of INL. Future progress reports and milestone tracking will be completed under requirements of new DOE Award Number DE-PS36-08GO98014. The following are excerpts from the project Peer Review completed in 2006. They describe the project in some detail. Additional information can be found by reviewing DOE Award Number: DE-PS36-08GO98014. 5. Statement of Problem and Technical Barriers: The chemical pulping industry is one of the major users of fresh water in the United States. On average the industry uses over 80 tons of water to produce one ton of pulp, some states use up to 50% more (Washington 120 and Wisconsin 140). In order to process one ton of pulp using 80 tons of process water, a large amount of: • energy is used in process heat and • power is required for pumping the large volume of pulp slurries

  20. Hydrogen production from carrot pulp by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana

    NARCIS (Netherlands)

    Vrije, de G.J.; Budde, M.A.W.; Lips, S.J.J.; Bakker, R.R.; Mars, A.E.; Claassen, P.A.M.

    2010-01-01

    Hydrogen was produced from carrot pulp hydrolysate, untreated carrot pulp and (mixtures of) glucose and fructose by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana in pH-controlled bioreactors. Carrot pulp hydrolysate was obtained after enzymatic hydrolysis

  1. [State of the reproductive systemin in male rats of 1st generation obtained from irradiated parents and exposed to electromagnetic radiation (897 MHz) during embryogenesis and postnatal development].

    Science.gov (United States)

    Vereshchako, G G; Chueshova, N V; Gorokh, G A; Naumov, A D

    2014-01-01

    The consequences of prolonged exposure to electromagnetic radiation from cellular phone (897 MHz, daily 8 h/day) in male rats of the 1st generation obtained from irradiated parents and subjected to prolonged exposure to electromagnetic radiation of the range of mobile communications during ontogeny and postnatal development were studied. It has been found that irradiation causes a decrease in the number of births of animals, changing the sex ratio towards the increase in the number of males. It had a significant impact on the reproductive system of males, accelerating their sexual development, revealed at the age of two months. Radiation from cell phones led to significant disproportions in the cell number at different stages of spermatogenesis. It increased the number of mature spermatozoa which decreased viability.

  2. Sexual crossing of thermophilic fungus Myceliophthora heterothallica improved enzymatic degradation of sugar beet pulp.

    Science.gov (United States)

    Aguilar-Pontes, Maria Victoria; Zhou, Miaomiao; van der Horst, Sjors; Theelen, Bart; de Vries, Ronald P; van den Brink, Joost

    2016-01-01

    Enzymatic degradation of plant biomass requires a complex mixture of many different enzymes. Like most fungi, thermophilic Myceliophthora species therefore have a large set of enzymes targeting different linkages in plant polysaccharides. The majority of these enzymes have not been functionally characterized, and their role in plant biomass degradation is unknown. The biotechnological challenge is to select the right set of enzymes to efficiently degrade a particular biomass. This study describes a strategy using sexual crossing and screening with the thermophilic fungus Myceliophthora heterothallica to identify specific enzymes associated with improved sugar beet pulp saccharification. Two genetically diverse M. heterothallica strains CBS 203.75 and CBS 663.74 were used to generate progenies with improved growth on sugar beet pulp. One progeny, named SBP.F1.2.11, had a different genetic pattern from the parental strains and had improved saccharification activity after the growth on 3 % sugar beet pulp. The improved SBP saccharification was not explained by altered activities of the major (hemi-)cellulases. Exo-proteome analysis of progeny and parental strains after 7-day growth on sugar beet pulp showed that only 17 of the 133 secreted CAZy enzymes were more abundant in progeny SBP.F1.2.11. Particularly one enzyme belonging to the carbohydrate esterase family 5 (CE5) was more abundant in SBP.F1.2.11. This CE5-CBM1 enzyme, named as Axe1, was phylogenetically related to acetyl xylan esterases. Biochemical characterization of Axe1 confirmed de-acetylation activity with optimal activities at 75-85 °C and pH 5.5-6.0. Supplementing Axe1 to CBS 203.75 enzyme set improved release of xylose and glucose from sugar beet pulp. This study identified beneficial enzymes for sugar beet pulp saccharification by selecting progeny with improved growth on this particular substrate. Saccharification of sugar beet pulp was improved by supplementing enzyme mixtures with a previously

  3. Analysis of gene expression during odontogenic differentiation of cultured human dental pulp cells

    Directory of Open Access Journals (Sweden)

    Min-Seock Seo

    2012-08-01

    Full Text Available Objectives We analyzed gene-expression profiles after 14 day odontogenic induction of human dental pulp cells (DPCs using a DNA microarray and sought candidate genes possibly associated with mineralization. Materials and Methods Induced human dental pulp cells were obtained by culturing DPCs in odontogenic induction medium (OM for 14 day. Cells exposed to normal culture medium were used as controls. Total RNA was extracted from cells and analyzed by microarray analysis and the key results were confirmed selectively by reverse-transcriptase polymerase chain reaction (RT-PCR. We also performed a gene set enrichment analysis (GSEA of the microarray data. Results Six hundred and five genes among the 47,320 probes on the BeadChip differed by a factor of more than two-fold in the induced cells. Of these, 217 genes were upregulated, and 388 were down-regulated. GSEA revealed that in the induced cells, genes implicated in Apoptosis and Signaling by wingless MMTV integration (Wnt were significantly upregulated. Conclusions Genes implicated in Apoptosis and Signaling by Wnt are highly connected to the differentiation of dental pulp cells into odontoblast.

  4. Use of Residual Solids from Pulp and Paper Mills for Enhancing Strength and Durability of Ready-Mixed Concrete

    Energy Technology Data Exchange (ETDEWEB)

    Tarun R. Naik; Yoon-moon Chun; Rudolph N. Kraus

    2003-09-18

    This research was conducted to establish mixture proportioning and production technologies for ready-mixed concrete containing pulp and paper mill residual solids and to study technical, economical, and performance benefits of using the residual solids in the concrete. Fibrous residuals generated from pulp and paper mills were used, and concrete mixture proportions and productions technologies were first optimized under controlled laboratory conditions. Based on the mixture proportions established in the laboratory, prototype field concrete mixtures were manufactured at a ready-mixed concrete plant. Afterward, a field construction demonstration was held to demonstrate the production and placement of structural-grade cold-weather-resistant concrete containing residual solids.

  5. Potential of hot water extraction of birch wood to produce high-purity dissolving pulp after alkaline pulping.

    Science.gov (United States)

    Borrega, Marc; Tolonen, Lasse K; Bardot, Fanny; Testova, Lidia; Sixta, Herbert

    2013-05-01

    The potential of hot water extraction of birch wood to produce highly purified dissolving pulp in a subsequent soda-anthraquinone pulping process was evaluated. After intermediate extraction intensities, pulps with low xylan content (3-5%) and high cellulose yield were successfully produced. Increasing extraction intensity further decreased the xylan content in pulp. However, below a xylan content of 3%, the cellulose yield dramatically decreased. This is believed to be due to cleavage of glycosidic bonds in cellulose during severe hot water extractions, followed by peeling reactions during alkaline pulping. Addition of sodium borohydride as well as increased anthraquinone concentration in the pulping liquor increased the cellulose yield, but had no clear effects on pulp purity and viscosity. The low intrinsic viscosity of pulps produced after severe extraction intensities and soda-anthraquinone pulping corresponded to the viscosity at the leveling-off degree of polymerization, suggesting that nearly all amorphous cellulose had been degraded. Copyright © 2012 Elsevier Ltd. All rights reserved.

  6. Pemanfaatan Limbah Pulp Buah Semangka (Citrullus vulgaris, Schard) Untuk Pembuatan Nata De Watermelon Pulp Dengan Menggunakan Bakteri Acetobacter xylinum

    OpenAIRE

    Mawaddah

    2011-01-01

    This research done to know can or not the waste of watermelon pulp use to produce nata and how the effect of mass variation using to nata’s quality. This research was done with mass variation of watermelon pulp that is 10 g, 20 g, 30 g, 40 g, 50 g, 60 g, and watermelon pulp without adding sugar as control. Statistical analysis count the thickness, water content, ash content, fiber content and organoleptic test of texture, color, aroma, and taste of nata de watermelon pulp. The result show...

  7. Direct pulp capping after a carious exposure versus root canal treatment: a cost-effectiveness analysis.

    Science.gov (United States)

    Schwendicke, Falk; Stolpe, Michael

    2014-11-01

    Excavation of deep caries often leads to pulpal exposure even in teeth with sensible, nonsymptomatic pulps. Although direct pulp capping (DPC) aims to maintain pulpal health, it frequently requires follow-up treatments like root canal treatment (RCT), which could have been performed immediately after the exposure, with possibly improved outcomes. We quantified and compared the long-term cost-effectiveness of both strategies. A Markov model was constructed following a molar with an occlusally located exposure of a sensible, nonsymptomatic pulp in a 20-year-old male patient over his lifetime. Transition probabilities or hazard functions were estimated based on systematically and nonsystematically assessed literature. Costs were estimated based on German health care, and cost-effectiveness was analyzed using Monte Carlo microsimulations. Despite requiring follow-up treatments significantly earlier, teeth treated by DPC were retained for long periods of time (52 years) at significantly reduced lifetime costs (545 vs 701 Euro) compared with teeth treated by RCT. For teeth with proximal instead of occlusal exposures or teeth in patients >50 years of age, this cost-effectiveness ranking was reversed. Although sensitivity analyses found substantial uncertainty regarding the effectiveness of both strategies, DPC was usually found to be less costly than RCT. We found both DPC and RCT suitable to treat exposed vital, nonsymptomatic pulps. DPC was more cost-effective in younger patients and for occlusal exposure sites, whereas RCT was more effective in older patients or teeth with proximal exposures. These findings might change depending on the health care system and underlying literature-based probabilities. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  8. EPR detection of hydroxyl radical generation and oxidative perturbations in lead-exposed earthworms (Eisenia fetida) in the presence of decabromodiphenyl ether.

    Science.gov (United States)

    Liu, Kou; Chen, Lin; Zhang, Wei; Lin, Kuangfei; Zhao, Li

    2015-03-01

    Lead (Pb) and decabromodiphenyl ether (BDE209) are the main contaminants at e-waste recycling sites, and their potential toxicological effects on terrestrial organisms have received extensive attention. However, the impacts on the oxidative perturbations and hydroxyl radical (·OH) generation in earthworms of exposure to the two chemicals remain almost unknown. Therefore, indoor incubation tests were performed on control and contaminated soil samples to determine the effects of Pb in earthworms Eisenia fetida in the presence of BDE209 through the use of several biomarkers in microcosms. The results have demonstrated that the addition of BDE209 (1 or 10 mg kg(-1)) decreased the enzymatic activities [superoxide dismutase, catalase (CAT), peroxidase] and total antioxidant capacity (T-AOC) compared with exposure to BDE209 alone (50, 250 or 500 mg kg(-1)). Electron paramagnetic resonance spectra indicated that ·OH radicals in earthworms were significantly induced by Pb in the presence of BDE209. The changing pattern of malondialdehyde (MDA) contents was accordant with that of ·OH intensity suggested that reactive oxygen species might lead to cellular lipid peroxidation. Furthermore, CAT exhibited more sensitive response to single Pb exposure than the other biomarkers, while T-AOC, ·OH and MDA might be three most sensitive biomarkers in earthworms after simultaneous exposure to Pb and BDE209. The results of these observations suggested that oxidative stress appeared in E. fetida, and it may play an important role in inducing the Pb and BDE209 toxicity to earthworms.

  9. Free toe pulp flap for finger pulp and volar defect reconstruction

    Directory of Open Access Journals (Sweden)

    Jyoshid R Balan

    2016-01-01

    Full Text Available Background: Fingertip injury requiring flap cover is very common in the modern era. The ideal cover should fulfill both functional and aesthetic improvement. Materials and Methods: From June 2015 to April 2016, we performed seven free toe pulp flaps for finger defect reconstruction. All patients were males. Five flaps were done in emergency post-traumatic cases, and two were done in elective set up. The cases included reconstruction of three thumbs, one index and one ring finger in an emergency set up and two ring fingers in the elective. Thumb reconstruction was done with great toe lateral pulp and the other digits reconstructed with second toe pulp flap. Follow-up evaluation included both functional and aesthetic assessment. Results: Five flaps survived completely, one suffered partial loss, and one flap failed completely. The median follow-up period was 9 months. The median duration of surgery was 255 min (range 210 to 300 min. The median two-point discrimination was 6.5 mm (range 4–8 mm. There was the return of temperature sensation in all patients; two had cold intolerance. The Semmes-Weinstein monofilament score varied from 3.61 to 5.07 (median filament index value 4.31/pressure value of 2 g/mm2. Three patients had delayed donor site wound healing. Conclusions: The free toe pulp flap is an efficient choice for fingertip and volar finger defects reconstruction with an excellent tissue match.

  10. Cell-derived micro-environment helps dental pulp stem cells promote dental pulp regeneration.

    Science.gov (United States)

    Zhang, Xuexin; Li, Hui; Sun, Jingjing; Luo, Xiangyou; Yang, Hefeng; Xie, Li; Yang, Bo; Guo, Weihua; Tian, Weidong

    2017-10-01

    The function of the dental pulp is closely connected to the extracellular matrix (ECM) structure, and ECM has received significant attention due to its biological functions for regulating cells. As such, the interaction between the ECM niche and cells is worth exploring for potential clinical uses. In this study, dental pulp stem cell (DPSC)-derived ECM (DPM) was prepared through cell culture and decellularization to function as the cell niche, and changes in DPSC behaviour and histological analysis of dental pulp tissue regeneration were evaluated following the DPM culture. DPM promoted the replication of DPSCs and exhibited retention of their mineralization. Then, the DPM-based culture strategy under odontogenic culture medium was further investigated, and the mineralization-related markers showed that DPSCs were regulated towards odontogenic differentiation. Dental pulp-like tissue with well-arranged ECM was harvested after a 2-month subcutaneous implantation in nude mice with DPM application. Additionally, DPSCs cultured on the plastic culture surface showed the up-regulation of mineralization makers in vitro, but there was a disorder in matrix formation and mineralization when the cells were cultured in vivo. DPM-based cultivation could serve as a cell niche and modulate DPSC behaviour, and this method also provided an alternative to harvest tissue-specific ECM and provided a strategy for ECM-cell interaction. © 2017 John Wiley & Sons Ltd.

  11. Application of resin in pulp technique for ion exchange separation of uranium from alkaline leachate

    International Nuclear Information System (INIS)

    Sreenivas, T.; Rajan, K.; Chakravorty, J.

    2014-01-01

    The hydrometallurgical process for the recovery of uranium from different ores uses ion exchange (IX) technique for the separation of dissolved uranium values. Conventionally, the IX process is carried out on leach solution obtained after the filtration or counter-current decantation of the leach slurries. Amongst the two types of leach pulps generated in uranium ore processing, viz acidic and alkaline, the latter one consists of predominantly fine-size pulps of higher viscosity, thus making the solid-liquid separation an arduous task. Sustained research for improvising the efficiency of various unit operations in the uranium process flowsheet have resulted in advent of new generation resins which are mechanically re-silent, posses higher exchange capacity thereby enabling separation of dissolved uranium ions from the leach pulps directly. Some of the prominent low-grade uranium ore deposits in India are hosted in acid consuming gangue matrix. These ore deposits necessitate fine grinding as well as application of alkaline leaching for the dissolution of uranium values. The leach pulps analyse 500 – 600 mg/l of U3O8 and contain total dissolved solutes (TDS) to the extent of about 50 g/l. Analysis of the characteristics of the leach pulp indicated suitability of resin-in-pulp technique for the separation of uranyl carbonate anions from the leachate. This paper describes the results of the RIP test work on alkaline leach slurry using various commercially available strong base anionic exchange resins. Parametric variation studies were conducted to establish the adsorption isotherm and sorption kinetics followed by elution of loaded uranium. Based on these results semi-continuous experiments on “carousel” mode were carried out. The results indicate superiority of gel type polystyrene based resins grafted with quaternary ammonium ion in comparison to the macro-porous resins. Semi-continuous counter-current extraction and elution tests indicated that about 98% of

  12. Interappointment emergencies in teeth with necrotic pulps.

    Science.gov (United States)

    Alaçam, Tayfun; Tinaz, Ali Cemal

    2002-05-01

    The incidence of interappointment emergencies in symptomatic and asymptomatic teeth with necrotic pulps was evaluated, and severity of flare-ups was determined by a quantitative method using a flare-up index. There were no significant differences in the incidence of flare-ups attributable to gender, age, diameter of lesion, taking analgesics, placebos, or no medication, or preoperative symptomatic or asymptomatic tooth diagnoses (p > 0.05). There were significantly more painful flare-ups in mandibular teeth than in maxillary (p < 0.05).

  13. Influence of moderate to severe chronic periodontitis on dental pulp.

    Science.gov (United States)

    Fatemi, K; Disfani, R; Zare, R; Moeintaghavi, A; Ali, Saadat A; Boostani, H R

    2012-10-01

    The relationship between periodontal disease and dental pulp changes is controversial and has been debated for many years. This human study was performed to evaluate the possible effects of moderate to advanced periodontal disease on the different aspect of dental pulp structure. Twenty hopeless permanent teeth were extracted from systemically healthy adults because of moderate to advanced chronic periodontitis, with a bone loss of >6 mm and a mobility of grade 2 or 3. Upon extraction, the apical 2 to 3 mm of the roots were immediately sectioned. Four to five sections were mounted on each slide, and every third slide was stained with hematoxylin and eosin. The specimens were histologically processed and examined by an oral pathologist. Non-inflamed pulp, with partial or complete necrosis in some sections and several non-necrotic sections, was found in only 6.3% of teeth. Most teeth (58.3%) displayed edematous pulps. Slightly fibrotic pulps were seen in 52.1% of sections. Odontoblastic integrity was seen in 31.3% of teeth. Most teeth (77.1%) displayed no pulp stones. In 43.8% of teeth, the pulp vessels displayed dilatation. Moderate to advanced periodontal disease can affect the dental pulp. Careful consideration of diagnostic and treatment planing in patients with endodontic-periodontal involvement is therefore recommended.

  14. Influence of moderate to severe chronic periodontitis on dental pulp

    Science.gov (United States)

    Fatemi, K; Disfani, R; Zare, R; Moeintaghavi, A; Ali, Saadat A.; Boostani, H. R

    2012-01-01

    Background: The relationship between periodontal disease and dental pulp changes is controversial and has been debated for many years. This human study was performed to evaluate the possible effects of moderate to advanced periodontal disease on the different aspect of dental pulp structure. Materials and Methods: Twenty hopeless permanent teeth were extracted from systemically healthy adults because of moderate to advanced chronic periodontitis, with a bone loss of >6 mm and a mobility of grade 2 or 3. Upon extraction, the apical 2 to 3 mm of the roots were immediately sectioned. Four to five sections were mounted on each slide, and every third slide was stained with hematoxylin and eosin. The specimens were histologically processed and examined by an oral pathologist. Results: Non-inflamed pulp, with partial or complete necrosis in some sections and several non-necrotic sections, was found in only 6.3% of teeth. Most teeth (58.3%) displayed edematous pulps. Slightly fibrotic pulps were seen in 52.1% of sections. Odontoblastic integrity was seen in 31.3% of teeth. Most teeth (77.1%) displayed no pulp stones. In 43.8% of teeth, the pulp vessels displayed dilatation. Conclusions: Moderate to advanced periodontal disease can affect the dental pulp. Careful consideration of diagnostic and treatment planing in patients with endodontic-periodontal involvement is therefore recommended. PMID:23493524

  15. Differentiation ability of rat postnatal dental pulp cells in vitro.

    NARCIS (Netherlands)

    Zhang, W.; Walboomers, X.F.; Wolke, J.G.C.; Bian, Z.; Fan, M.W.; Jansen, J.A.

    2005-01-01

    The current rapid progression in stem cell research has enhanced our knowledge of dental tissue regeneration. In this study, rat dental pulp cells were isolated and their differentiation ability was evaluated. First, dental pulp cells were obtained from maxillary incisors of male Wistar rats.

  16. 78 FR 38877 - Kraft Pulp Mills NSPS Review

    Science.gov (United States)

    2013-06-28

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

  17. Eggshells – assisted hydrolysis of banana pulp for biogas production

    African Journals Online (AJOL)

    KARAKANA

    In this study, pretreatment of banana pulp using eggshells in both calcined and un-calcined forms to examine the ... Key words: Anaerobic digestion, banana pulp hydrolysis biogas, eggshells. .... obtain fine powder. ..... using pig waste and cassava peels. ... from bioethanol waste: the effect of pH and urea addition to biogas.

  18. Pulpal blood flow recorded from exposed dentine with a laser Doppler flow meter using red or infrared light.

    Science.gov (United States)

    Kijsamanmith, Kanittha; Vongsavan, Noppakun; Matthews, Bruce

    2018-03-01

    To determine the percentage of the blood flow signal that is derived from dental pulp when recording from exposed dentine in a human premolar. Recordings were made from 7 healthy teeth in 5 subjects (aged 22-33 yr.) with a laser Doppler flow meter (Periflux 4001) using either a red (635 nm) or an infrared (780 nm) laser. After exposing dentine above the buccal pulpal horn (cavity diam. 1.6 mm, depth 3 mm) and isolating the crown with opaque rubber dam, blood flow was recorded alternately with infrared or red light from the exposed dentine under four conditions: before and after injecting local anaesthetic (3% Mepivacaine without vasoconstrictor) (LA) over the apex of the root of the tooth; after exposing the pulp by cutting a buccal, class V cavity in the tooth; and after sectioning the coronal pulp transversely through the exposure. There was no significant change in mean blood flow recorded with either light source when the tooth was anaesthetized or when the pulp was exposed. After the pulp had been sectioned, the blood flow recorded with infrared light fell by 67.8% and with red light, by 68.4%. The difference between these effects was not significant. When recording blood flow from exposed coronal dentine with either infrared or red light in a tooth isolated with opaque rubber dam, about 68% to the signal was contributed by the pulp. The signal:noise ratio was better with infrared than red light, and when recording from dentine than enamel. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. National design environment for pulp mills; Kansallinen paperitehtaan suunnitteluympaeristoe - PMST 03

    Energy Technology Data Exchange (ETDEWEB)

    Kaijaluoto, S [VTT Energy, Jyvaeskylae (Finland)

    1999-12-31

    The research to be done in the CACTUS research programme produces new process models and generates new knowledge about the influence of various contaminants on the runnability and the quality of paper. The generated information calls for an environment where it can be analysed and utilised. The goal of the project is to build a design environment for papermaking processes. The environment will be composed of a number of tools, all integrated together, that can be used in process design from preliminary concept screening through detailed simulation studies to the design and tuning of control systems. The design environment is based on the Balas and APMS simulation programmes developed at VTT. Balas is a general steady-state simulation package for chemical processes with emphasis on pulp and paper. Recent applications include the analysis of the influence of new drying techniques on the energy and water management of a paper mill and the evaluation of new paper machine and water treatment concepts. APMS (Advanced Pulp and Paper Mill Simulator) is a new flexible tool intended for fast modelling and efficient simulation of the dynamic performance the various unit processes in pulp and paper mill, or even of the whole integrated mill. (orig.)

  20. National design environment for pulp mills; Kansallinen paperitehtaan suunnitteluympaeristoe - PMST 03

    Energy Technology Data Exchange (ETDEWEB)

    Kaijaluoto, S. [VTT Energy, Jyvaeskylae (Finland)

    1998-12-31

    The research to be done in the CACTUS research programme produces new process models and generates new knowledge about the influence of various contaminants on the runnability and the quality of paper. The generated information calls for an environment where it can be analysed and utilised. The goal of the project is to build a design environment for papermaking processes. The environment will be composed of a number of tools, all integrated together, that can be used in process design from preliminary concept screening through detailed simulation studies to the design and tuning of control systems. The design environment is based on the Balas and APMS simulation programmes developed at VTT. Balas is a general steady-state simulation package for chemical processes with emphasis on pulp and paper. Recent applications include the analysis of the influence of new drying techniques on the energy and water management of a paper mill and the evaluation of new paper machine and water treatment concepts. APMS (Advanced Pulp and Paper Mill Simulator) is a new flexible tool intended for fast modelling and efficient simulation of the dynamic performance the various unit processes in pulp and paper mill, or even of the whole integrated mill. (orig.)

  1. Nemesia root hair response to paper pulp substrate for micropropagation.

    Science.gov (United States)

    Labrousse, Pascal; Delmail, David; Decou, Raphaël; Carlué, Michel; Lhernould, Sabine; Krausz, Pierre

    2012-01-01

    Agar substrates for in vitro culture are well adapted to plant micropropagation, but not to plant rooting and acclimatization. Conversely, paper-pulp-based substrates appear as potentially well adapted for in vitro culture and functional root production. To reinforce this hypothesis, this study compares in vitro development of nemesia on several substrates. Strong differences between nemesia roots growing in agar or in paper-pulp substrates were evidenced through scanning electron microscopy. Roots developed in agar have shorter hairs, larger rhizodermal cells, and less organized root caps than those growing on paper pulp. In conclusion, it should be noted that in this study, in vitro microporous substrates such as paper pulp lead to the production of similar root hairs to those found in greenhouse peat substrates. Consequently, if agar could be used for micropropagation, rooting, and plant acclimatization, enhancement could be achieved if rooting stage was performed on micro-porous substrates such as paper pulp.

  2. Path analysis for selection of feijoa with greater pulp weight

    Directory of Open Access Journals (Sweden)

    Joel Donazzolo

    Full Text Available ABSTRACT: The objective of this paper was to identify the direct and indirect effects of feijoa fruits (Acca sellowiana traitson pulp weight, in order to use these traits in indirect genotypes selection. Fruits of five feijoa plants were collected in Rio Grande do Sul, in the years of 2009, 2010 and 2011. Six traits were evaluated: diameter, length, total weight, pulp weight, peel thickness and number of seeds per fruit. In the path analysis, with or without ridge regression, pulp weight was considered as the basic variable, and the other traits were considered as explanatory variables. Total weight and fruit diameter had high direct effect, and are the main traits associated with pulp weight. These traits may serve as criteria for indirect selection to increase feijoa pulp weight, since they are easy to be measured.

  3. Holdup time measurement by radioactive tracers in pulp production

    International Nuclear Information System (INIS)

    Roetzer, H.; Donhoffer, D.

    1988-12-01

    A batch of pulp was to be labelled before passing two bleaching towers of a pulp plant. Activated glass fibres were used as a tracer, which contained 24-Na with a half-life of 15 hours. It was shown in laboratory tests, that the glass fibres were suitable for transport studies of wood pulp. For use in the tests the fibres were activated and suspended in water. Due to the small diameter of the fibres (2-5 micrometers) this suspension shows physical properties very similar to the pulp. For detection six scintillation probes were mounted at different positions outside the bleaching tower. Radiation protection during the test was very easy due to the low total activity of the tracer material. Residence time distributions for both towers were measured. The successful tracer experiments show, that the method of labelling is suited for investigations of material transport in the pulp and paper industry. 3 figs., 11 refs., 2 tabs. (Author)

  4. Questioning Conventional Wisdom Regarding the Most Suitable Sequence of Enzyme Usage in Pulp Bleaching

    Directory of Open Access Journals (Sweden)

    Avdhesh Kumar Gangwar

    2015-11-01

    Full Text Available Increased public scrutiny and governmental legislation towards the pulp and paper industries have motivated industrialists and researchers to seek improved bleaching sequences having the potential to minimize pollutants in bleach effluent generated during manufacturing of paper. Discovery of toxic chlorinated organics and their components in bleach effluents has focused people’s attention towards finding alternative ways of bleaching pulp. Use of enzymes at industrial scale has become well known, but still it is not clear whether the sequence of enzymatic treatment most often employed in industrial applications represents the best overall practice. The point of enzyme addition is critically important to maximize benefits. Many publications describe the use of an enzyme treatment stage before the use of chemicals in a bleaching process. Insufficient attention has been paid to the alternatives of adding an enzyme in between chemical bleaching agents (intermediate or at the end of the bleaching process.

  5. Influence of crude oil and pulp and paper mill effluent on mixed infections of Trichodina cottidarium and T. saintjohnsi (Ciliophora) parasitizing Myoxocephalus octodecemspinosus and M. scorpius

    International Nuclear Information System (INIS)

    Khan, R.A.; Barker, D.E.; Williams-Ryan, K.; Hooper, R.G.

    1994-01-01

    Samples of longhorn sculpin (Myoxocephalus octodecemspinosus) were exposed to sediment contaminated with crude oil or pulp and paper mill effluent for periods up to 13 months in the laboratory. Other samples were collected at sites where crude oil or effluent from a pulp and paper mill are discharged. The intensity of gill infections of Trichodina spp. on exposed fish was significantly higher than on controls 5, 9, and 13 months after exposure. The intensity of the ciliates was also greater on sculpins collected near an oil-receiving terminal than on those sampled 5 km from the polluted site. Field collections of longhorn and shorthorn (Myoxocephalus scorpius) sculpins at and distant from a pulp and paper mill had high and low intensities of the ciliates, respectively. Similarly, the intensity of trichodinid ciliates was also significantly greater in longhorn sculpins exposed to effluent-contaminated sediment than in controls 5 months after exposure. The results suggest that the intensity of gill-inhibiting species such as trichodinids in susceptible fish hosts increases after chronic exposure to crude oil and to pulp and paper mill effluent, and the parasites may serve as indicators of pollution. 24 refs., 4 figs., 1 tab

  6. Investigation of pulping and paper making potential of weeds

    Directory of Open Access Journals (Sweden)

    omid Ghaffarzadeh Mollabashi

    2017-08-01

    Full Text Available Increasing use of wood products accompanying with resource constraint has revealed the importance of nonwood based material. In this study, pulping and papermaking potential of three varieties of weeds including Xanthium spinosum, Carthamus tinctorius and Cyperus papyrus have been considered. At first, chemical components of the samples i.e. cellulose, lignin and extractives have been measured following TAPPI standard test methods. Afterwards, pulping process based as soda and Kraft has been carried out and the pulp properties i.e. screen yield and reject, kappa number, caliper, bust index, tear index, brightness have been considered. According to the results, the amount cellulose, lignin and extractives have been measured for the Xanthium spinosum %38.15, %13.5 and 4.72, respectively. Theses parameters have been estimated about %38.25, %10.3 and % 2.95 for Carthamus tinctorius and %38.8, %19.2 and 4.4 in case of papyrus. The yield of soda and Kraft pulp of the papyrus was more than Xanthium spinosum and Carthamus tinctorius. Among all treatments, the highest screen yield related to soda pulping of Cyperus papyrus by %39.8 which has been obtained by 175 centigrade as a maximum temperature, L/W: 6/1, active alkaline: %30 and 90 minutes as the time at temperature. The lowest and highest amounts of the tear index were related to soda pulp sample of the Carthamus tinctorius and Kraft pulp sample of Xanthium spinosum by 2.49 and 8.1, respectively. In addition, the lowest and highest amounts of the bursting index were related to soda pulp sample of the Cyperus papyrus and Kraft pulp sample of Xanthium spinosum by 0.61and 2.48, respectively. Meanwhile, soda pulp sample of the Cyperus papyrus showed the highest amount of brightness with %45 ISO.

  7. Isolation and Characterization of Human Dental Pulp Stem Cells from Cryopreserved Pulp Tissues Obtained from Teeth with Irreversible Pulpitis.

    Science.gov (United States)

    Malekfar, Azin; Valli, Kusum S; Kanafi, Mohammad Mahboob; Bhonde, Ramesh R

    2016-01-01

    Human dental pulp stem cells (DPSCs) are becoming an attractive target for therapeutic purposes because of their neural crest origin and propensity. Although DPSCs can be successfully cryopreserved, there are hardly any reports on cryopreservation of dental pulp tissues obtained from teeth diagnosed with symptomatic irreversible pulpitis during endodontic treatment and isolation and characterization of DPSCs from such cryopreserved pulp. The aim of this study was to cryopreserve the said pulp tissues to propagate and characterize isolated DPSCs. A medium consisting of 90% fetal bovine serum and 10% dimethyl sulfoxide was used for cryopreservation of pulp tissues. DPSCs were isolated from fresh and cryopreserved pulp tissues using an enzymatic method. Cell viability and proliferation were determined using the MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay. DPSC migration and interaction were analyzed with the wound healing assay. Mesenchymal characteristics of DPSCs were verified by flow cytometric analysis of cell surface CD markers. The osteogenic and adipogenic potential of DPSCs was shown by von Kossa and oil red O staining methods, respectively, and the polymerase chain reaction method. We found no significant difference in CD marker expression and osteogenic and adipogenic differentiation potential of DPSCs obtained from fresh and cryopreserved dental pulp tissue. Our study shows that dental pulp can be successfully cryopreserved without losing normal characteristics and differentiation potential of their DPSCs, thus making them suitable for dental banking and future therapeutic purposes. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  8. Hygroscopic behavior of lyophilized acerola pulp powder

    Directory of Open Access Journals (Sweden)

    Luciana C. Ribeiro

    2016-03-01

    Full Text Available ABSTRACT Powder products are characterized by their practicality and long life. However, fruit powders have high hygroscopicity and tend to agglomerate due to its hydrophilic nature. The isotherms of equilibrium moisture content apply to the study of dehydrated food preservation potential. Acerola is a nutritionally rich fruit, with great economic and industrial potential. The objective of this study was to analyse acerola powder adsorption isotherms obtained by lyophilization and characterize the powder obtained from lyophilized acerola pulp. Analysis of hygroscopicity, solubility and degree of caking were performed. Isotherms were represented by the mathematical models of GAB, BET, Henderson and Oswin, at temperatures of 25, 35 and 45 °C. According to the results, the obtained powder showed hygroscopicity of 5.96 g of absorbed water 100g-1 of solids, solubility of 95.08% and caking of 14.12%. The BET model showed the best fit to the adsorption isotherms of the acerola pulp powder obtained by lyophilization. The obtained isotherm was of type III, with a "J" shape. There was an inversion of the effect of temperature on the isotherms of acerola powders.

  9. Pulp and paper mill effluent treatments have differential endocrine-disrupting effects on rainbow trout.

    Science.gov (United States)

    Orrego, Rodrigo; Guchardi, John; Hernandez, Victor; Krause, Rachelle; Roti, Lucia; Armour, Jeffrey; Ganeshakumar, Mathumai; Holdway, Douglas

    2009-01-01

    Endocrine disruption (ED) effects due to pulp and paper mill effluents extracts involving different industrial procedures and effluent treatments (nontreated, primary, and secondary treated) were evaluated using immature triploid rainbow trout in a pulse-exposure toxicity experiment. The protocol involved the use of intraperitoneal injection of mill extracts (solid-phase extraction [SPE]) corrected for individual fish weight and included several laboratory standards (steroidal hormones and phytosterols). Biological endpoints at two different levels of biological organization were analyzed (molecular and individual organism). Results indicated that nonsignificant changes were observed in the individual physiological indices represented by condition factor, liver somatic index, and gonad somatic index during the experiment. Significant induction of liver ethoxyresorufin-O-deethylase activity was observed between different effluent treatments and experimental controls. Significant endocrine-disrupting effects at the reproductive level were observed in all effluent treatments involving significant increments in plasma vitellogenin (VTG) levels. Fish exposed to untreated effluent extracts had significantly higher VTG levels compared to fish exposed to primary and secondary treatment effluent extracts, indicating a decrease of the estrogenic effect due to the effluent treatment. The present study has shown that for the Chilean pulp and paper mill SPE extracts evaluated, an endocrine disruption effect was induced in immature triploid rainbow, reaffirming the significant estrogenic effects demonstrated previously in laboratory and field experiments.

  10. Development of hemicelluloses biorefineries for integration into kraft pulp mills

    Science.gov (United States)

    Ajao, Olumoye Abiodun

    The development and wide spread acceptance of production facilities for biofuels, biochemicals and biomaterials is an important condition for reducing reliance on limited fossil resources and transitioning towards a global biobased economy. Pulp and paper mills in North America are confronted with high energy prices, high production costs and intense competition from emerging economies and low demand for traditional products. Integrated forest biorefineries (IFBR) have been proposed as a mean to diversify their product streams, increase their revenue and become more sustainable. This is feasible because they have access to forest biomass, an established feedstock supply chain and wood processing experience. In addition, the integration of a biorefinery process that can share existing infrastructure and utilities on the site of pulp mill would significantly lower investment cost and associated risks. Kraft pulping mills are promising receptor processes for a biorefinery because they either possess a prehydrolysis step for extracting hemicelluloses sugars prior to wood pulping or it can be added by retrofit. The extracted hemicelluloses could be subsequently transformed into a wide range of value added products for the receptor mill. To successfully implement hemicelluloses biorefinery, novel processes that are technically and economically feasible are required. It is necessary to identify products that would be profitable, develop processes that are energy efficient and the receptor mill should be able to supply the energy, chemicals and material demands of the biorefinery unit. The objective of this thesis is to develop energy efficient and economically viable hemicelluloses biorefineries for integration into a Kraft pulping process. A dissolving pulp mill was the reference case study. The transformation of hemicellulosic sugars via a chemical and biochemical conversion pathway, with furfural and ethanol as representative products for each pathway was studied. In

  11. Nano-hydroxyapatite and calcium-enriched mixture for pulp capping of sound primary teeth: a randomized clinical trial.

    Science.gov (United States)

    Haghgoo, Roza; Asgary, Saeed; Mashhadi Abbas, Fatemeh; Montazeri Hedeshi, Roshanak

    2015-01-01

    Nano-hydroxyapatite (NHA) has been used for regeneration of osseous defects. Calcium-enriched mixture (CEM) cement is also used for various dental treatments. This trial compared the efficacy of NHA and CEM cement for direct pulp capping (DPC) of sound primary teeth. In this randomized clinical trial with split-mouth design, after attaining informed consent, 20 sound primary canines scheduled for orthodontic extraction, were selected. After mechanical pulp exposure, the exposed site was capped with either NHA or CEM cement and then immediately restored with glass-ionomer and resin composite. The teeth were extracted after two months and examined histologically. Parameters of hard tissue bridge (HTB) formation, its type and quality as well as pulpal inflammation scores were compared between the two experimental groups. The data were analyzed using the Mann Whitney U and Fisher's exact test. The level of significance was set at 0.001. All CEM specimens showed inflammation score of 0 (less than 10%). However, in NHA group, inflammation scores of 0 (less than 10%), 1 (10%-30%) and 2 (30%-50%) were observed in 2 (20%), 4 (40%) and 4 (40%) specimens, respectively (P<0.001). HTB was formed in all CEM specimens while it was developed in 2 specimens of NHA (20%; P<0.001). All CEM specimens showed normal pulp; only two cases in NHA group (20%) demonstrated uninflamed normal pulp. CEM cement was superior to NHA as a DPC agent in terms of HTB formation and pulp inflammation scores. It is a suitable material for the DPC of primary teeth.

  12. Performance of a Horizontal Triple Cylinder Type Pulping Machine

    Directory of Open Access Journals (Sweden)

    Sukrisno Widyotomo

    2011-05-01

    Full Text Available Pulping is one important step in wet coffee processing method. Pulping process usually uses a machine which constructed by wood or metal materials. A horizontal single cylinder type of fresh coffee cherries pulping machine is the most popular machine in coffee processing. One of the weaknesses of a horizontal single cylinder type of fresh coffee cherries pulping machine is higher in broken beans. Broken bean is one of mayor aspects in defect system that contribute to low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type of fresh coffee cherries pulping machine which resulted in 12.6—21.4% of broken beans. To reduce percentage of broken beans, Indonesian Coffee and Cocoa Research Institute has developed and tested a horizontal triple cylinder type of fresh coffee cherries pulping machine. Material tested was fresh mature Robusta coffee cherries, 60—65% (wet basis moisture content; has classified on 3 levels i.e. unsorted, small and medium, and clean from metal and foreign materials. The result showed that the machine produced 6,340 kg/h in optimal capacity for operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 55.5% whole parchment coffee, 3.66% broken beans, and 1% beans in wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

  13. Dental Pulp Defence and Repair Mechanisms in Dental Caries.

    Science.gov (United States)

    Farges, Jean-Christophe; Alliot-Licht, Brigitte; Renard, Emmanuelle; Ducret, Maxime; Gaudin, Alexis; Smith, Anthony J; Cooper, Paul R

    2015-01-01

    Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

  14. Dental Pulp Defence and Repair Mechanisms in Dental Caries

    Directory of Open Access Journals (Sweden)

    Jean-Christophe Farges

    2015-01-01

    Full Text Available Dental caries is a chronic infectious disease resulting from the penetration of oral bacteria into the enamel and dentin. Microorganisms subsequently trigger inflammatory responses in the dental pulp. These events can lead to pulp healing if the infection is not too severe following the removal of diseased enamel and dentin tissues and clinical restoration of the tooth. However, chronic inflammation often persists in the pulp despite treatment, inducing permanent loss of normal tissue and reducing innate repair capacities. For complete tooth healing the formation of a reactionary/reparative dentin barrier to distance and protect the pulp from infectious agents and restorative materials is required. Clinical and in vitro experimental data clearly indicate that dentin barrier formation only occurs when pulp inflammation and infection are minimised, thus enabling reestablishment of tissue homeostasis and health. Therefore, promoting the resolution of pulp inflammation may provide a valuable therapeutic opportunity to ensure the sustainability of dental treatments. This paper focusses on key cellular and molecular mechanisms involved in pulp responses to bacteria and in the pulpal transition between caries-induced inflammation and dentinogenic-based repair. We report, using selected examples, different strategies potentially used by odontoblasts and specialized immune cells to combat dentin-invading bacteria in vivo.

  15. Sisal organosolv pulp as reinforcement for cement based composites

    Directory of Open Access Journals (Sweden)

    Ana Paula Joaquim

    2009-09-01

    Full Text Available The present work describes non-conventional sisal (Agave sisalana chemical (organosolv pulp from residues of cordage as reinforcement to cement based materials. Sisal organosolv pulp was produced in a 1:1 ethanol/water mixture and post chemically and physically characterized in order to compare its properties with sisal kraft pulp. Cement based composites reinforced with organosolv or kraft pulps and combined with polypropylene (PP fibres were produced by the slurry de-watering and pressing method as a crude simulation of the Hatschek process. Composites were evaluated at 28 days of age, after exposition to accelerated carbonation and after 100 soak/dry cycles. Composites containing organosolv pulp presented lower mechanical strength, water absorption and apparent porosity than composites reinforced with kraft pulp. The best mechanical performance after ageing was also achieved by samples reinforced with kraft pulp. The addition of PP fibres favoured the maintenance of toughness after ageing. Accelerated carbonation promoted the densification of the composites reinforced with sisal organosolv + PP fibres.

  16. Scaffolds to Control Inflammation and Facilitate Dental Pulp Regeneration

    Science.gov (United States)

    Colombo, John S.; Moore, Amanda N.; Hartgerink, Jeffrey D.; D’Souza, Rena N.

    2014-01-01

    In dentistry, the maintenance of a vital dental pulp is of paramount importance, as teeth devitalized by root canal treatment may become more brittle and prone to structural failure over time. Advanced carious lesions can irreversibly damage the dental pulp by propagating a sustained inflammatory response throughout the tissue. While the inflammatory response initially drives tissue repair, sustained inflammation has an enormously destructive effect on the vital pulp, eventually leading to total necrosis of the tissue and necessitating its removal. The implications of tooth devitalization have driven significant interest in the development of bioactive materials that facilitate the regeneration of damaged pulp tissues by harnessing the capacity of the dental pulp for self-repair. In considering the process by which pulpitis drives tissue destruction, it is clear that an important step in supporting the regeneration of pulpal tissues is the attenuation of inflammation. Macrophages, key mediators of the immune response, may play a critical role in the resolution of pulpitis due to their ability to switch to a pro-resolution phenotype. This process can be driven by the resolvins, a family of molecules derived from fatty acids that show great promise as therapeutic agents. In this review, we outline the importance of preserving the capacity of the dental pulp to self-repair through the rapid attenuation of inflammation. Potential treatment modalities, such as shifting macrophages to a pro-resolving phenotype with resolvins are described, and a range of materials known to support the regeneration of dental pulp are presented. PMID:24698696

  17. Microarray expression profiling of human dental pulp from single subject.

    Science.gov (United States)

    Tete, Stefano; Mastrangelo, Filiberto; Scioletti, Anna Paola; Tranasi, Michelangelo; Raicu, Florina; Paolantonio, Michele; Stuppia, Liborio; Vinci, Raffaele; Gherlone, Enrico; Ciampoli, Cristian; Sberna, Maria Teresa; Conti, Pio

    2008-01-01

    Microarray is a recently developed simultaneous analysis of expression patterns of thousand of genes. The aim of this research was to evaluate the expression profile of human healthy dental pulp in order to find the presence of genes activated and encoding for proteins involved in the physiological process of human dental pulp. We report data obtained by analyzing expression profiles of human tooth pulp from single subjects, using an approach based on the amplification of the total RNA. Experiments were performed on a high-density array able to analyse about 21,000 oligonucleotide sequences of about 70 bases in duplicate, using an approach based on the amplification of the total RNA from the pulp of a single tooth. Obtained data were analyzed using the S.A.M. system (Significance Analysis of Microarray) and genes were merged according to their molecular functions and biological process by the Onto-Express software. The microarray analysis revealed 362 genes with specific pulp expression. Genes showing significant high expression were classified in genes involved in tooth development, protoncogenes, genes of collagen, DNAse, Metallopeptidases and Growth factors. We report a microarray analysis, carried out by extraction of total RNA from specimens of healthy human dental pulp tissue. This approach represents a powerful tool in the study of human normal and pathological pulp, allowing minimization of the genetic variability due to the pooling of samples from different individuals.

  18. A modified efficient method for dental pulp stem cell isolation

    Directory of Open Access Journals (Sweden)

    Maryam Raoof

    2014-01-01

    Full Text Available Background: Dental pulp stem cells can be used in regenerative endodontic therapy. The aim of this study was to introduce an efficient method for dental pulp stem cells isolation. Materials and Methods: In this in-vitro study, 60 extracted human third molars were split and pulp tissue was extracted. Dental pulp stem cells were isolated by the following three different methods: (1 digestion of pulp by collagenase/dispase enzyme and culture of the released cells; (2 outgrowth of the cells by culture of undigested pulp pieces; (3 digestion of pulp tissue pieces and fixing them. The cells were cultured in minimum essential medium alpha modification (αMEM medium supplemented with 20% fetal bovine serum(FBS in humid 37°C incubator with 5% CO 2 . The markers of stem cells were studied by reverse transcriptase polymerase chain reaction (PCR. The student t-test was used for comparing the means of independent groups. P <0.05 was considered as significant. Results: The results indicated that by the first method a few cell colonies with homogenous morphology were detectable after 4 days, while in the outgrowth method more time was needed (10-12 days to allow sufficient numbers of heterogeneous phenotype stem cells to migrate out of tissue. Interestingly, with the improved third method, we obtained stem cells successfully with about 60% efficiency after 2 days. The results of RT-PCR suggested the expression of Nanog, Oct-4, and Nucleostemin markers in the isolated cells from dental pulps. Conclusion: This study proposes a new method with high efficacy to obtain dental pulp stem cells in a short time.

  19. Basic effects of pulp refining on fiber properties--a review.

    Science.gov (United States)

    Gharehkhani, Samira; Sadeghinezhad, Emad; Kazi, Salim Newaz; Yarmand, Hooman; Badarudin, Ahmad; Safaei, Mohammad Reza; Zubir, Mohd Nashrul Mohd

    2015-01-22

    The requirement for high quality pulps which are widely used in paper industries has increased the demand for pulp refining (beating) process. Pulp refining is a promising approach to improve the pulp quality by changing the fiber characteristics. The diversity of research on the effect of refining on fiber properties which is due to the different pulp sources, pulp consistency and refining equipment has interested us to provide a review on the studies over the last decade. In this article, the influence of pulp refining on structural properties i.e., fibrillations, fine formation, fiber length, fiber curl, crystallinity and distribution of surface chemical compositions is reviewed. The effect of pulp refining on electrokinetic properties of fiber e.g., surface and total charges of pulps is discussed. In addition, an overview of different refining theories, refiners as well as some tests for assessing the pulp refining is presented. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Lauryl Amine as heavy metal collector of boiler ash from pulp and paper mill waste

    Science.gov (United States)

    Sembiring, M. P.; Kaban, J.; Bangun, N.; Saputra, E.

    2018-04-01

    Theincreasing of demand of pulp and paper products, will following with the growing the pulp and paper industryand generate significant mill waste. The total waste reached 1/3 of the amount raw materials used and ash boiler is the waste with the largest percentage of 52%. For that it takes effort to manage the existing waste. The boiler ash contained the chemical elements, it can be utilized such as fertilizer, because it also contains transition metals in form of heavy metal such as Cadmium (Cd), Cobalt (Co), Chrome (Cr), Cupprum (Cu), Ferrum (Fe), Nickel (Ni), and Zinc (Zn), the use of boiler ash must follow the threshold specified by the Government. Several studies have been undertaken to reduce and extract heavy metals from ash and sand of the boiler by using carbon dioxide as its ligand. Eelectrochemical method was used to remove and recovery of heavy metals from the incenerator. This study focused on removal of heavy metals using Lauryl Amine as collector and three solvents namely Dichloromethane, Ethanol and n-Hexane. The treatmentswas able to extract the heavy metal and generally reduce the heavy metal content of ash boiler pulp and paper mill waste. The combination treatment used toreduce the heavy metal content of 5 gram Lauryl Amine collector in Dichloromethane solvent for 4 hours process time.

  1. Impact of pulp and paper mill effluents and solid wastes on soil mineralogical and physicochemical properties.

    Science.gov (United States)

    Adhikari, Gopi; Bhattacharyya, Krishna G

    2015-03-01

    The present study was carried out to evaluate the impact of the effluents and the solid wastes generated by a giant pulp and paper mill in the northeastern part of India on soil mineralogy of the area. The impacts were monitored by analysis of soil samples from seven sites located in the potential impact zone and a control site where any kind of effluent discharge or solid waste dumping was absent. The soil belonged to medium texture type (sandy clay loam, sandy loam, loamy sand, and silt loam), and the soil aggregate analysis indicated higher levels of organic carbon, pH, electrical conductivity, effective cation exchange capacity, and mean weight diameter at sites receiving effluents and solid wastes from the pulp and paper mill. Depletion in soil silica level and in feldspar and quartz contents and rise in iron and calcium contents at the sites receiving effluents from the pulp and paper mill indicated significant influence on soil mineralogy. The soil contained a mixture of minerals consisting of tectosilicates (with silicate frameworks as in quartz or feldspar), phylosilicates (layered clays like kaolinite, smectite, chlorite, illite, etc.), and carbonates. Absence of pure clay minerals indicated a state of heterogeneous intermediate soil clay transformation. The significance of the mixed mineralogy in relation to the disposal of effluents and dumping of solid wastes is discussed in details.

  2. Kinetics of pulp mill effluent treatment by ozone-based processes

    International Nuclear Information System (INIS)

    Ko, Chun-Han; Hsieh, Po-Hung; Chang, Meng-Wen; Chern, Jia-Ming; Chiang, Shih-Min; Tzeng, Chewn-Jeng

    2009-01-01

    The wastewaters generated from wood pulping and paper production processes are traditionally treated by biological and physicochemical processes. In order to reduce chemical oxygen demand (COD) and color to meet increasingly strict discharge standards, advanced oxidation processes (AOPs) are being adapted as polishing treatment units. Various ozone-based processes were used in this study to treat simulated wastewaters prepared from black liquor from a hardwood Kraft pulp mill in Taiwan. The experimental results showed that the COD and color were primarily removed by direct ozone oxidation and activated carbon adsorption. While the addition of activated carbon could enhance the COD and color removal during ozonation, the addition of hydrogen peroxide improved the color removal only. For the various ozone-based treatment processes, kinetic models were developed to satisfactorily predict the COD and color removal rates. According to the kinetic parameters obtained from the various ozone-based processes, the enhanced COD and color removal of ozonation in the presence of activated carbon was attributed to the regeneration of the activated carbon by ozonation. These kinetic models can be used for reactor design and process design to treat pulping wastewater using ozone-based processes.

  3. ON THE RECOVERY OF HEMICELLULOSE BEFORE KRAFT PULPING

    Directory of Open Access Journals (Sweden)

    Carlos Vila,

    2012-07-01

    Full Text Available To assess the feasibility of implementing hemicellulose recovery stages in kraft mills, Eucalyptus globulus wood samples were subjected to aqueous treatments with hot, compressed water (autohydrolysis processing to achieve partial dissolution of xylan. Autohydrolyzed solids were subjected to kraft pulping under selected conditions to yield a pulp of low kappa number, and to an optimized TCF bleaching sequence made up of three stages (alkaline oxygen delignification, chelating, and pressurized hydrogen peroxide, with minimized additions of pulping and bleaching chemicals. The final product had a relatively low kappa number (1.4, 641 mL/g ISO intrinsic viscosity, and 86.4% brightness.

  4. Optimization of Dithionite Bleaching of High Yield Bagasse Pulp

    International Nuclear Information System (INIS)

    Mohamed, E.

    2005-01-01

    High yield bagasse pulp was prepared by soaking bagasse in 10 % cold sodium hydroxide for 24 hours and then refluxing for two hours at 95 degree C. Optimization of dithionite bleaching was attained by investigation of different parameters as consistency, temperature, time and ph. Effect of additives as chelating agent (EDTA) or stabilizing of bleaching solution (Zn compound and hexamethylene tetramine) was considered. The effect of air content was also studied. One and two stages bleaching of the pulp were investigated by using sodium dithionite (D) as a sole bleaching agent or after application of one stage bleaching by hydrogen peroxide to attain high brightness for high yield pulp

  5. Chemi-thermomechanical pulping of para rubber waste wood

    Energy Technology Data Exchange (ETDEWEB)

    Kubo, T.; Hosokawa, J.; Kobayashi, T.; Kobayashi, Y.

    1981-01-01

    The addition of NaOH to Na/sub 2/SO/sub 3/-treated waste wood chips (Hevea brasiliensis) increased long fiber fraction, Klason lignin content and bulk density, improved breaking length and tear factor, and decreased energy consumption in refining and brightness of resulting chemithermomechanical pulp. Lowering in brightness by alkali treatment was recovered by H/sub 2/O/sub 2/ bleaching, and bleaching with 8% H/sub 2/O/sub 2/ on pulp gave pulp with 61.3% brightness.

  6. Method and apparatus for assaying wood pulp fibers

    Science.gov (United States)

    Gustafson, Richard [Bellevue, WA; Callis, James B [Seattle, WA; Mathews, Jeffrey D [Neenah, WI; Robinson, John [Issaquah, WA; Bruckner, Carsten A [San Mateo, CA; Suvamakich, Kuntinee [Seattle, WA

    2009-05-26

    Paper pulp is added to a stain solution. The stain solution and pulp fibers are mixed to form a slurry. Samples are removed from the slurry and are admixed with dilution water and a bleach. Then, the fibers are moved into a flow cell where they are subjected to a light source adapted to stimulate fluorescence from the stained pulp fiber. Before the fiber slurry enters the flow cell it is mixed with a dilution water of bleach to reduce background fluorescence. The fluorescent light is collimated and directed through a dichroic filter onto a fluorescence splitting dichroic filter.

  7. Authors's reply to 'Generation of surface degraded layer on austenitic stainless steel piping exposed to flowing sodium in a loop: inter comparison of long term exposure data', by S. Rajendran Pillai

    International Nuclear Information System (INIS)

    Ganesan, Vaidehi; Ganesan, V.; Borgstedt, H.U.

    2004-01-01

    This is an elaborate author's reply to a comment 'Generation of surface degraded layer on austenitic steel piping exposed to flowing sodium in a loop: inter comparison of long term exposure data' by S. Rajendran Pillai appearing in this proceedings. The basic misunderstanding as seen in the above comment about the mass loss due to sodium exposure, which is reflected throughout the above comment, has been explained in detail in this reply for better understanding of the phenomenon. It is precisely mentioned and understood that Thorley and Tyzack model deals with complete mass loss and not mere degradation. The total mass loss corresponds to mass loss due to wall thinning and that due to degraded layer formation. Though Thorley and Tyzack model is the most pioneering model in the field of sodium corrosion, the inadequacies of this model for materials without molybdenum such as SS 304 with very long exposure in sodium is clearly brought out in this paper. This model has been successfully applied to calculate life of clad tubes, which have relatively short stay in reactor core. Yoshida models are highlighted and compared with our experimental results. Yoshida models are not valid below certain durations owing to the empirical nature of such expressions. Thorley and Tyzack model can be used for SS 316 LN as this alloy contains molybdenum and nitrogen both of which imparts corrosion resistance in sodium. What is required is that one needs to establish the extent to which this model can be applied for materials exposed to high temperatures and very long durations. The details are discussed in this reply

  8. Buildings exposed to fire

    International Nuclear Information System (INIS)

    1987-01-01

    The 24 lectures presented to the colloquium cover the following subject fields: (1) Behaviour of structural components exposed to fire; (2) Behaviour of building materials exposed to fire; (3) Thermal processes; (4) Safety related, theoretical studies. (PW) [de

  9. Can Acceptable Pulp be Obtained from Eucalyptus globulus Wood Chips after Hemicellulose Extraction?

    OpenAIRE

    Francisco López; M. Trinidad García; Vicente Mena; J. Mauricio Loaiza; Minerva A. M. Zamudio; Juan C. García

    2014-01-01

    This study investigates the operating conditions used in the soda-anthraquinone pulping of Eucalyptus globulus wood after autohydrolysis pretreatment on the yield, kappa number, and brightness of the resulting unbleached pulp. Moreover, strength-related properties of the resulting handsheets was examined to identify the best pulping conditions and compare the outcome with that of a conventional soda-anthraquinone pulping process. The paper strength properties of the pulp were similar to or be...

  10. Ecotoxicological studies with newly hatched larvae of Concholepas concholepas (Mollusca, Gastropoda): bioassay with secondary-treated kraft pulp mill effluents.

    Science.gov (United States)

    Manríquez, Patricio H; Llanos-Rivera, Alejandra; Galaz, Sylvana; Camaño, Andrés

    2013-12-01

    The Chilean abalone or "loco" (Concholepas concholepas, Bruguière 1789) represent the most economically important marine recourse exploited from inner inshore Management and Exploitation Areas for Benthic Resources along the Chilean coast. In this study, newly-hatched larvae of C. concholepas were investigated as a potential model species for marine ecotoxicological studies. The study developed a behavioral standard protocol for assessing the impact that kraft pulp mill effluents after secondary treatment have on C. concholepas larvae. Under controlled laboratory conditions, newly-hatched larvae were exposed to a series of different concentrations of kraft pulp mill effluents with secondary treatment (Pinus spp. and Eucalyptus spp.), potassium dichromate as standard reference toxicant and effluent-free control conditions. Regardless of the type of effluent the results indicated that diluted kraft pulp effluent with secondary treatment had reduced effect on larval survival. Low larval survivals were only recorded when they were exposed to high concentrations of the reference toxicant. This suggests that C. concholepas larval bioassay is a simple method for monitoring the effects of kraft pulp mill effluents with secondary treatment discharged into the sea. The results indicated that dilution of ca. 1% of the effluent with an elemental chlorine free (ECF) secondary treatment is appropriate for achieving low larval mortalities, such as those obtained under control conditions with filtered seawater, and to minimize their impact on early ontogenetic stages of marine invertebrates such as newly-hatched larvae of C. concholepas. The methodological aspects of toxicological testing and behavioral responses described here with newly-hatched larvae of C. concholepas can be used to evaluate in the future the potential effects of other stressful conditions as other pollutants or changes in seawater pH associated with ocean acidification. © 2013 Elsevier Inc. All rights

  11. Nutrient contents of the fresh pulps and dried pulp cakes of vitellaria paradoxa of Gulu District, Uganda

    DEFF Research Database (Denmark)

    Oryema, Christine; Oryem-Origa, Hannington; Roos, Nanna

    2016-01-01

    Vitellaria paradoxa Gaertn locally known as ‘Yaa’ in Acholi is a valuable edible indigenous wild fruit in Gulu District, northern Uganda. It is a multipurpose fruit tree and highly favoured by the inhabitants of this district. Its fruit pulps are eaten when fresh and/or made into cakes and dried....... This study determined the nutrient compositions of the fresh pulps and dried pulp cakes of V. paradoxa. Laboratory analyses were undertaken to determine the micro and macro nutrients in the samples on fresh (FM) and dry matter (DM) basis following standard procedures and protocols. The potassium, sodium...

  12. Pulp Stone, Haemodialysis, End-stage Renal Disease, Carotid Atherosclerosis

    OpenAIRE

    Patil, Santosh; Sinha, Nidhi

    2013-01-01

    Objectives: The aim of this study was to determine the relationship between the presence of pulp calcification and carotid artery calcification on the dental panoramic radiographs in End Stage Renal Disease (ESRD) patients who were on haemodialysis.

  13. UTILIZATION OF Prosopis afiicana PULP FOR RABBIT FEEDING: 2

    African Journals Online (AJOL)

    IBB

    The formulated diets contained similar crude protein content of 18%. The apparent ... These results indicate that Prosopis africana pulp can completely replace maize in the diets of ... serum albumin were determined by Biuret reactions. (Bush ...

  14. Processing pineapple pulp into dietary fibre supplement | Ackom ...

    African Journals Online (AJOL)

    Processing pineapple pulp into dietary fibre supplement. ... The pasting characteristics or properties of wheat flour fortified with the product up to 20 ... of some popular foods to help increase the fibre intake and health of the general population.

  15. Effects of feeding cassava pulp fermented with Acremonium ...

    African Journals Online (AJOL)

    Acer

    2017-01-27

    #, T. .... Briefly, 10 kg steamed cassava pulp (87.5% DM) was soaked with sterile water (1 : 1). .... The data on digestibility and retention of broilers are presented in Table 3. .... Taken together, the antioxidant capacity of A.

  16. Partial pulp necrosis caused by excessive orthodontic force

    Directory of Open Access Journals (Sweden)

    Min-Young Kim

    2011-03-01

    Full Text Available As the dental pulp is encased with a rigid, noncompliant shell, changes in pulpal blood flow or vascular tissue pressure can have serious implication for the health of pulp. Numerous studies have demonstrated that orthodontic force application may influence both blood flow and cellular metabolism, leading degenerative and/or inflammatory responses in the dental pulp. The aim of this case report is to present a case about tooth with chronic periapical abscess which showed normal vital responses. Excessive orthodontic force is thought to be the prime cause of partial pulp necrosis. Owing to remaining vital tissue, wrong dianosis can be made, and tooth falsely diagnosed as vital may be left untreated, causing the necrotic tissue to destroy the supporting tissuses. Clinician should be able to utilize various diagnostic tools for the precise diagnosis, and be aware of the endodontic-orthodontic inter-relationship.

  17. Proximate and Mineral Composition of the Pulp of Chrysophyllum ...

    African Journals Online (AJOL)

    MBI

    2014-11-13

    Nov 13, 2014 ... The results showed that the fruit pulp of Chrysophyllum albidum contained essential ... seed of the plant is a good source of oil which is ... Sample Collection and Treatment ... AAS machine due to its good precision and.

  18. NIRS Characterization of Paper Pulps to Predict Kappa Number

    Directory of Open Access Journals (Sweden)

    Ana Moral

    2015-01-01

    Full Text Available Rice is one of the most abundant food crops in the world and its straw stands as an important source of fibres both from an economic and an environmental point of view. Pulp characterization is of special relevance in works involving alternative raw materials, since pulp properties are closely linked to the quality of the final product. One of the analytical techniques that can be used in pulp characterization is near-infrared spectroscopy (NIRS. The use of NIRS has economic and technical advantages over conventional techniques. This paper aims to discuss the convenience of using NIRS to predict Kappa number in rice straw pulps produced under different conditions. We found that the resulting Kappa number can be acceptably estimated by NIRS, as the errors obtained with that method are similar to those found for other techniques.

  19. Factors influencing cassava - pulp fermentation period for gari ...

    African Journals Online (AJOL)

    Factors influencing cassava - pulp fermentation period for gari processing among ... Result of probit model analysis at 5% significance level shows an R value ... Marital status (2.236**) and respondents' cultural influences (1.960**) were ...

  20. Claustral single cell reactions to tooth pulp stimulation in cats.

    Science.gov (United States)

    Jastreboff, P; Sikora, M; Frydrychowski, A; Słoniewski, P

    1983-01-01

    Single unit activity in the central region of the claustrum, evoked by electrical stimulation of tooth pulp or paws was studied on cats under chloralose anesthesia. The majority of cells responded in similar manner to stimulation of tooth pulp or paws, but there were cells with clear preference to a given type of stimulation. Latencies of reactions evoked by tooth pulp stimulation were significantly shorter than those for limb stimulation. In the former case latencies as short as 8 rns were observed. It is postulated that the central region of the claustrum receives a projection from the tooth pulp, and that in those cases with very short latency the projection is direct and does not involve the cerebral cortex.

  1. Prevalence and Analysis of Factors Related to Occurrence of Pulp ...

    African Journals Online (AJOL)

    Uche

    between pulp stone and pristine posterior teeth, chronic periodontitis and posterior teeth ... Conclusion: It is recommended that researchers should pay special care in case selections, and ... (1982) reported a PS prevalence rate of 20.7 % in.

  2. STUDIES ON HIBISCUS CANNABINUS, HIBISCUS SABDARIFFA, AND CANNABINUS SATIVA PULP TO BE A SUBSTITUTE FOR SOFTWOOD PULP- PART 1: AS-AQ DELIGNIFICATION PROCESS

    OpenAIRE

    Dharm Dutt; J. S. Upadhyaya; C. H. Tyagi

    2010-01-01

    Hibiscus cannabinus, Hibiscus sabdariffa, and Cannabinus sativa, which are renewable non-woody fiber resources having characteristics similar to that of softwood (bast fibers), when used together with hardwood (core fibers), gave higher pulp yield with good mechanical strength properties when using an alkaline sulphite-anthraquinone (AS-AQ) pulping process rather than a conventional kraft pulping process and bleached more readily than kraft and soda pulps with a CEHH bleaching sequence. A com...

  3. Timing of pulp extirpation for replanted avulsed teeth.

    LENUS (Irish Health Repository)

    Stewart, Chris

    2009-01-01

    A search was performed (April 2004) across four databases, namely Ovid Medline, Cochrane Library, PubMed and Web of Science, relevant to the proposed PICO ( Patient or problem, Intervention, Comparison, Outcome) question: (P) for a replanted avulsed permanent tooth, (I) is early pulp extirpation within 10-14 days of replantation, (C) compared with delayed pulp extirpation, (O) associated an increased likelihood of successful periodontal healing after tooth replantation. Only articles published in the English language were considered.

  4. Pectin methyl esterase activity in apple and orange pulps

    International Nuclear Information System (INIS)

    Abdullaev, A.; Djumaev, B.B.; Djumaev, N.B.; Mukhidinov, Z.K.

    2008-01-01

    The results of pectin methyl esterase activity from apple, orange pulp and orange peel depending of ph and temperature are discussed. It's shown that the methyl esterase activity form apple and orange pulps higher in range of temperatures from +37...+60 d ig C . The analysis of dependence of its activity from ph has shown that in both case the enzyme activity increase with increase of ph

  5. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    Energy Technology Data Exchange (ETDEWEB)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J., E-mail: rosemarymj@lifecarehll.com

    2016-04-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  6. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    International Nuclear Information System (INIS)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J.

    2016-01-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  7. Pulp fictions of medieval England: Essays in popular romance

    OpenAIRE

    McDonald, Nicola

    2004-01-01

    Middle English popular romance is the most audacious and compendious testimony to the imaginary world of the English Middle Ages. Yet, with few exceptions, it remains under read and under studied. Pulp fictions of medieval England demonstrates that popular romance merits and rewards serious critical attention and that it is crucial to our understanding of the complex and conflicted world of medieval England. Pulp fictions of medieval England comprises ten essays on individual romances that, w...

  8. Future CO2 removal from pulp mills - Process integration consequences

    International Nuclear Information System (INIS)

    Hektor, Erik; Berntsson, Thore

    2007-01-01

    Earlier work has shown that capturing the CO 2 from flue gases in the recovery boiler at a pulp mill can be a cost-effective way of reducing mill CO 2 emissions. However, the CO 2 capture cost is very dependent on the fuel price. In this paper, the potential for reducing the need for external fuel and thereby the possibility to reduce the cost for capturing the CO 2 are investigated. The reduction is achieved by using thermal process integration. In alternative 1, the mill processes are integrated and a steam surplus made available for CO 2 capture, but still there is a need for external fuel. In alternative 2, the integration is taken one step further, the reboiler is fed with MP steam, and the heat of absorption from the absorption unit is used for generation of LP steam needed at the mill. The avoidance costs are in both cases lower than before the process integration. The avoidance cost in alternative 1 varies between 25.4 and 30.7 EUR/tonne CO 2 depending on the energy market parameters. For alternative 2, the cost varies between 22.5 and 27.2 EUR/tonne CO 2 . With tough CO 2 reduction targets and correspondingly high CO 2 emission costs, the annual earnings can be substantial, 18.6 MEUR with alternative 1 and 21.2 MEUR with alternative 2

  9. Effects of washed platelets vs platelet-rich plasma on the proliferation and mineralization of rat dental pulp cells.

    Science.gov (United States)

    Zhang, L; Xie, Y H; Lin, B R

    2015-08-14

    We examined the effects of washed platelets (WPLTs) and platelet-rich plasma (PRP) on the proliferation and mineralization of rat dental pulp cells. Rat dental pulp cells were separated, cultured, and identified. Medium containing 1, 10, 100, or 500 mL/L PRP or WPLTs was added to 4th generation cells. The MTS method was used to determine cell proliferation. Alizarin red staining was used to observe the formation of mineralized nodules after cell mineralization and induction for 10 and 20 days under different culture conditions, and the areas of the mineralized nodules formed 20 days after induction were computed. The addition of 1, 10, and 100 mL/L WPLTs or PRP significantly promoted rat dental pulp cell proliferation (P 0.05). Under the same concentrations, no significant differences on cell proliferation were observed between WPLT and PRP treatments (P > 0.05 in all groups). After 10 days mineralization and culture, the 100 and 500 mL/L WPLT and PRP group positive nodule rates were significantly higher than those of the low concentration and the control groups (P < 0.05). After 20 days, the areas of the mineralized nodules formed in the 100 and 500 mL/L WPLT and PRP groups were significantly larger than those in the control group (P < 0.05). These results demonstrate that both WPLTs and PRP are equally able to significantly promote the proliferation and calcification of rat dental pulp cells under a certain range of concentrations.

  10. Sugar, acid and furfural quantification in a sulphite pulp mill: Feedstock, product and hydrolysate analysis by HPLC/RID.

    Science.gov (United States)

    Llano, Tamara; Quijorna, Natalia; Andrés, Ana; Coz, Alberto

    2017-09-01

    Waste from pulp and paper mills consist of sugar-rich fractions comprising hemicellulose derivatives and cellulose by-products. A complete characterisation of the waste streams is necessary to study the possibilities of an existing mill. In this work, four chromatographic methods have been developed to obtain the most suitable chromatographic method conditions for measuring woody feedstocks, lignocellulosic hydrolysates and cellulose pulp in sulphite pulping processes. The analysis of major and minor monosaccharides, aliphatic carboxylic acids and furfurals has been optimised. An important drawback of the spent liquors generated after sulphite pulping is their acidic nature, high viscosity and adhesive properties that interfere in the column lifetime. This work recommends both a CHO-782Pb column for the sugar analysis and an SH-1011 resin-based cross-linked gel column to separate low-molecular-weight chain acids, alcohols and furfurals. Such columns resulted in a good separation with long lifetime, wide pH operating range and low fouling issues.

  11. Seeking optimality in fruit pulping schedules: A case study*

    Directory of Open Access Journals (Sweden)

    J.H. Van Vuuren

    2014-01-01

    Full Text Available The process of scheduling fruit pulping for the production of fruit juices is of great importance in the beverage industry. Decisions have to be made regarding available processing time, the disposal of fruit that will not be pulped before stock loss due to spoilage, the fulfilment of customer demand and an optimal financial position. Sheduling depends on the capacity of the work force, pulping machine limitations and delivery deadlines. However, the situation is often encountered where the plant manager has to decide which fruit batches (usually from stock piles of overwhelming proportions during the harvesting season are to be pulped in order to minimize losses due to fruit deterioration. Such decisions are usually done manually, based on intuition and experience. A mathematical model is presented here which constructs a pulping strategy while minimising cascading financial losses associated with fruit grade drops within the stock pile. It is shown in particular that a minimisation of fruit losses is not a good criterion for optimality, and that substantial financial gains may be accomplished when minimising financial losses in stead of fruit losses, which is currently standard practice at most fruit pulping plants.

  12. Water requirements of the pulp and paper industry

    Science.gov (United States)

    Mussey, Orville D.

    1955-01-01

    Water, of varied qualities, is used for several purposes in the manufacture of pulp and paper, as a vehicle for transporting the constituents of paper in the paper machines; as process water for cooking wood chips to make pulp; as a medium for heat transfer; and for washing the pulpwood, the woodpulp, and the machines that handle the pulp. About 3,200 million gallons of water was withdrawn from surface- and ground-water sources each day during 1950 for the use of the pulp and paper industry. This is about 4 percent of the total estimated industrial withdrawal of water in the Nation The paper industry in the United States has been growing at a rapid rate. It has increased about tenfold in the last 50 years and has doubled every 15 years. The 1950 production of paper was about 24 million tons, which amounts to about 85 percent of the domestic consumption. In 1950, the pulp mills of the country produced more than 14 million tons of woodpulp, which supplied about 85 percent of the demand by the paper mills and other industries. The remainder of the fiber for paper manufacture was obtained from imported woodpulp, from reclaimed wastepaper, and from other fibers including rags and straw. The nationwide paper consumption for 1955 has been estimated at 31,700,000 tons. Woodpulp is classified according to the process by which it is made. Every woodpulp has characteristics that are carried over into the many and diverse grades of paper. Groundwood pulp is manufactured by simply grinding up wood and refining the resulting product. Soda, sulfite, and sulfate pulps are manufactured by chemically breaking down the lignin that cements the cellulose of the wood together and removing, cleaning, and sometimes bleaching the resulting fibers. Some woodpulp is produced by other methods. Sulfate-pulp mills are increasing in number and in rated daily capacity and are manufacturing more than half of the present domestic production of woodpulp. Most of the newer and larger woodpulp mills

  13. The Kraft Pulp And Paper Properties of Sweet Sorghum Bagasse (Sorghum bicolor L Moench

    Directory of Open Access Journals (Sweden)

    Widya Fatriasari

    2015-05-01

    Full Text Available This study investigated the potency of sweet sorghum (Sorghum bicolor bagasse as raw material for pulp and paper using kraft pulping. The effects of alkali and sulfidity loading on kraft pulp and paper properties were also investigated. The pulping condition of the kraft pulp consisted of three levels of alkali loading (17, 19 and 22% and sulfidity loading (20, 22 and 24%. The maximum cooking temperature was 170°C for 4 h with a liquid to wood ratio of 10:1. Kraft pulping of this Numbu bagasse produced good pulp indicated by high screen yield and delignification selectivity with a low Kappa number (< 10. The unbleached pulp sheet produced a superior brightness level and a high burst index. The increase of active alkali loading tended to produce a negative effect on the pulp yield, Kappa number and paper sheet properties. Therefore, it is suggested to use a lower active alkaline concentration.

  14. Repair Responses of Dental Pulp to Tooth Injury and Biological Properties of Dentin-pulp Complex

    OpenAIRE

    大島, 勇人; Ohshima, Hayato

    2004-01-01

    Regeneration-the creation of a new tissue after the original one has been lost-is the fundamental biological capability in an organism. Numerous organs are considered to contain stem cells referred to as adult stem cells, even in the adult. Adult stem cells can give rise to a limited set of adult tissue types. In the field of clinical dentistry, it is well-known that the dentin-pulp complex is capable of repair after tooth injuries such as tooth replantation/transplantation or restorative pro...

  15. Pulp tissue inflammation and angiogenesis after pulp capping with transforming growth factor β1

    Directory of Open Access Journals (Sweden)

    Sri Kunarti

    2008-06-01

    Full Text Available In Restorative dentistry the opportunity to develop biomemitic approaches has been signalled by the possible use of various biological macromolecules in direct pulp capping reparation. The presence of growth factors in dentin matrix and the putative role indicating odontoblast differentiation during embryogenesis has led to the examination on the effect of endogenous TGF-β1. TGF-β1 is one of the Growth Factors that plays an important role in pulp healing. The application of exogenous TGF-β1 in direct pulp capping treatment should be experimented in fibroblast tissue in-vivo to see the responses of inflammatory cells and development of new blood vessels. The increase in food supplies always occurs in the process of inflammation therefore the development of angiogenesis is required to fulfil the requirement. This in-vivo study done on orthodontic patients indicated for premolar extraction between 10–15 years of age. A class V cavity preparation was created in the buccal aspect 1 mm above gingival margin to pulp exposure. The cavity was slowly irrigated with saline solution and dried using a sterile small cotton pellet. The sterile absorbable collagen membrane was applied and soaked in 5 ml TGF-β1. It was covered by a Teflon pledge to separate from Glass Ionomer Cement restoration. Evaluation was performed on day 7; 14; and 21. All samples were histopathologycally examined and data was statistically analysed using one way ANOVA and Dunnet T3.There were no inflammatory symptoms in clinical examination on both Ca(OH2 and TGF-β1, but they increased the infiltration of inflammatory cells on histopathological examination. There were no significant differences (p > 0.05 between Ca(OH2 and TGF-β1 in inflammation cell and significant differences (p < 0.05 in angiogenesis on day 7 and 14. There were no significant differences (p > 0.05 in inflammation cell with in TGF-β1 groups and significant differences (p < 0.05 with in Ca(OH2 groups on day 7

  16. Dry Kraft Pulping at Ambient Pressure for Cost Effective Energy Saving and Pollution Deduction

    Energy Technology Data Exchange (ETDEWEB)

    Yulin Deng; Art Ragauskas

    2012-08-28

    Sponsored by the DOE Industrial Energy Efficiency Grand Challenge program, our research team at the Georgia Institute of Technology conducted laboratory studies and confirmed the concept of making wood pulp using a dry pulping technology. This technology is a new process different from any prior pulping technology used in Kraft and CTMP pulping. Three different kinds of dry pulping methods were investigated. (a) Dry Pulping at Atmospheric Pressure: The first one is to dry and bake the pretreated woodchips in a conventional oven at atmospheric pressure without the use of a catalyst. (b) Dry Pulping at Reduced Pressure: The second method is to dry the pretreated woodchips first in a vacuum oven in the presence of anthraquinone (AQ) as a pulping catalyst, followed by baking at elevated temperature. (c) Liquid Free Chemical Pulping, LFCP. The third method is to first remove the free water of pretreated woodchips, followed by dry pulping using a conventional Kraft pulping digester with AQ and triton as additives. Method one: Experimental results indicated that Dry Pulping at Atmospheric Pressure could produce pulp with higher brightness and lower bulk than conventional Kraft pulp. However, tensile strength of the acquired pulp is much lower than traditional Kraft pulp, and their Kappa number and energy consumption are higher than conventional Kraft pulp. By fully analyzing the results, we concluded that wood fibers might be damaged during the drying process at elevated temperature. The main reason for wood fiber damage is that a long drying time was used during evaporation of water from the woodchips. This resulted in an un-uniform reaction condition on the woodchips: the outside layer of the woodchips was over reacted while inside the woodchips did not reacted at all. To solve this problem, dry pulping at reduced pressure was investigated. Method two: To achieve uniform reaction throughout the entire reaction system, the water inside the pretreated woodchips was

  17. Understanding about the classification of pulp inflammation

    Directory of Open Access Journals (Sweden)

    Trijoedani Widodo

    2007-03-01

    Full Text Available Since most authors use the reversible pulpitis and irreversible pulpitis classification, however, many dentists still do not implement these new classifications. Research was made using a descriptive method by proposing questionnaire to dentists from various dental clinics. The numbers of the dentists participating in this research are 22 dentists. All respondents use the diagnosis sheet during their examinations on patients. Nonetheless, it can't be known what diagnosis card used and most of the dentists are still using the old classification. Concerning responses given towards the new classification: a the new classification had been heard, however, it was not clear (36.3%; b the new classification has never been heard at all (63.6%. Then, responses concerning whether a new development is important to be followed-up or not: a there are those who think that information concerning new development is very important (27.2%; b those who feel that it is important to have new information (68.3%; c those who think that new information is not important (8%. It concluded that information concerning the development of classification of pulp inflammation did not reach the dentists.

  18. Bacterial infections of pulp and periodontal origin.

    Science.gov (United States)

    González-Moles, Miguel Angel; González, Nabila M

    2004-01-01

    The anatomical and structural characteristics of the pulp make this structure prone to altering as a result of, for instance, periodontal conditions (proximity), iatrogenic alterations, infections and involvement of vascular and nerve structures (it is surrounded by hard tissues that prevent expansion), to name just a few. Pulpitis is a process that courses with pain of varying intensity that allows us to determine the location of the lesion in clinical terms. Its evolution varies and may even progress to pulpar necrosis that in turn, produces neuritis-like pain. Diagnosis is established by means of clinical symptomatology and supported by X-rays, palpation of tissues at painful sites, application of electrical stimuli, heat, etc. Periodontitis is a bacterial infection originating in the apex. The most important form is the so-called acute apical periodontitis that arises as a result of a prior episode of pulpitis. It is characterized by acute pain located in the tooth, accompanied by the feeling of having a long-tooth. The patient refers being unable to chew on that side; there may be painful mobility of the tooth and an outflow of pus that alleviates symptoms. X-rays do not provide a lot of information, but may attest to a widening of the apical space. This pathology may disseminate to surrounding tissues, leading to conditions of considerable severity.

  19. Prospect of trema orientalis as a pulping raw material in bangladesh

    International Nuclear Information System (INIS)

    Jahan, M.S.

    2013-01-01

    The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

  20. Research on Wheat Straw Pulping with Ionic Liquid 1-Ethyl-3-Methylimidazole Bromide

    Directory of Open Access Journals (Sweden)

    Wei Song

    2016-12-01

    Full Text Available In this paper, the pulping process of wheat straw using ionic liquid 1-ethyl-3-methylimidazolium bromide ([Emim]Br as the digestion liquor is presented. The influence of pulping conditions on the pulp yield are analysed by single-factor and orthogonal experiments, and optimum pulping conditions are obtained. The average pulp yield reaches 44 %, and the average recovery rate of ionic liquid is 93.5 %. The XRD pattern shows no obvious change in the crystal structure of the wheat straw cellulose. Additionally, the SEM image illustrates that there are many fine fibres in the pulp and the spaces between the fibres are large.

  1. The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

    Directory of Open Access Journals (Sweden)

    Kátia Maria Morais Eiras

    2009-01-01

    Full Text Available Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxide in sequences ending with a chlorine dioxide stage but similarly in sequences ending with a final peroxide stage. The use of secondary condensate for pulp washing decreases reversion.

  2. Cynara cardunculus L. alkaline pulps: alternatives fibres for paper and paperboard production.

    Science.gov (United States)

    Abrantes, S; Amaral, M E; Costa, A P; Duarte, A P

    2007-11-01

    The pulping of Cynara cardunculus L. (cardoon) was performed under conditions for kraft, kraft-AQ and soda-AQ processes. The best results in terms of delignification degree, expressed as kappa number, pulp viscosity and screened yield, were obtained for the kraft-AQ process with 0.20% of anthraquinone (AQ). The papermaking potential of the selected pulp was studied attending to biometric fibre characterisation, refining aptitude, optical and strength properties. All properties were compared against a Eucalyptus globulus pulp at different refining degrees. The cardoon pulp was also evaluated concerning its potential to board manufacture, alone and in mixtures with pine pulp, giving rise to promising results for liner manufacture.

  3. Long term effects of bioactive glass particulates on dental pulp stem cells in vitro

    Directory of Open Access Journals (Sweden)

    Gholami Sanaz

    2017-12-01

    Full Text Available Bioactive glasses (BG are known for their ability to induce bone formation by the action of their dissolution products. Glasses can deliver active ions at a sustained rate, determined by their composition and surface area. Nanoporous sol-gel derived BGs can biodegrade rapidly, which can lead to a detrimental burst release of ions and a pHrise. The addition of phosphate into the glass can buffer the pH during dissolution. Here, dissolution of BG with composition 60 mol% SiO2, 28 mol% CaO and 12 mol% P2O5 at 600 μg/ml were investigated. Initially, the dissolution and apatite formation of the BG particulates were examined in simulated body fluid using FTIR and XRD. BG particulates were indirectly exposed to dental pulp stem cells, and the effect of 14 days continuous ion release on human dental pulp stem cells (hDPSC viability and differentiation was evaluated. Alamar blue assay showed that cell proliferation was not inhibited by the continuous release of Ca, P and soluble silica. In fact, hDPSC in the presence of BG particulate displayed a higher density of mineralized nodules than untreated cells, as assessed by Alizarin red. The results will have a great contribution to the in vivo application of this particular BG.

  4. The effects of wood storage on the chemical composition and indigenous microflora of eucalyptus species used in the pulping industry

    CSIR Research Space (South Africa)

    Ramnath, L

    2018-02-01

    Full Text Available Lipophilic extractives naturally occurring in wood tend to coalesce during pulping to form pitch deposits, which have particularly undesirable effects on the pulping process and quality of pulp produced. A chemical characterization of different...

  5. Modified silk fibroin scaffolds with collagen/decellularized pulp for bone tissue engineering in cleft palate: Morphological structures and biofunctionalities

    International Nuclear Information System (INIS)

    Sangkert, Supaporn; Meesane, Jirut; Kamonmattayakul, Suttatip; Chai, Wen Lin

    2016-01-01

    Cleft palate is a congenital malformation that generates a maxillofacial bone defect around the mouth area. The creation of performance scaffolds for bone tissue engineering in cleft palate is an issue that was proposed in this research. Because of its good biocompatibility, high stability, and non-toxicity, silk fibroin was selected as the scaffold of choice in this research. Silk fibroin scaffolds were prepared by freeze-drying before immerging in a solution of collagen, decellularized pulp, and collagen/decellularized pulp. Then, the immersed scaffolds were freeze-dried. Structural organization in solution was observed by Atomic Force Microscope (AFM). The molecular organization of the solutions and crystal structure of the scaffolds were characterized by Fourier transform infrared (FT-IR) and X-ray diffraction (XRD), respectively. The weight increase of the modified scaffolds and the pore size were determined. The morphology was observed by a scanning electron microscope (SEM). Mechanical properties were tested. Biofunctionalities were considered by seeding osteoblasts in silk fibroin scaffolds before analysis of the cell proliferation, viability, total protein assay, and histological analysis. The results demonstrated that dendrite structure of the fibrils occurred in those solutions. Molecular organization of the components in solution arranged themselves into an irregular structure. The fibrils were deposited in the pores of the modified silk fibroin scaffolds. The modified scaffolds showed a beta-sheet structure. The morphological structure affected the mechanical properties of the silk fibroin scaffolds with and without modification. Following assessment of the biofunctionalities, the modified silk fibroin scaffolds could induce cell proliferation, viability, and total protein particularly in modified silk fibroin with collagen/decellularized pulp. Furthermore, the histological analysis indicated that the cells could adhere in modified silk fibroin

  6. Scaffold-free Prevascularized Microtissue Spheroids for Pulp Regeneration.

    Science.gov (United States)

    Dissanayaka, W L; Zhu, L; Hargreaves, K M; Jin, L; Zhang, C

    2014-12-01

    Creating an optimal microenvironment that mimics the extracellular matrix (ECM) of natural pulp and securing an adequate blood supply for the survival of cell transplants are major hurdles that need to be overcome in dental pulp regeneration. However, many currently available scaffolds fail to mimic essential functions of natural ECM. The present study investigated a novel approach involving the use of scaffold-free microtissue spheroids of dental pulp stem cells (DPSCs) prevascularized by human umbilical vein endothelial cells (HUVECs) in pulp regeneration. In vitro-fabricated microtissue spheroids were inserted into the canal space of tooth-root slices and were implanted subcutaneously into immunodeficient mice. Histological examination revealed that, after four-week implantation, tooth-root slices containing microtissue spheroids resulted in well-vascularized and cellular pulp-like tissues, compared with empty tooth-root slices, which were filled with only subcutaneous fat tissue. Immunohistochemical staining indicated that the tissue found in the tooth-root slices was of human origin, as characterized by the expression of human mitochondria, and contained odontoblast-like cells organized along the dentin, as assessed by immunostaining for nestin and dentin sialoprotein (DSP). Vascular structures formed by HUVECs in vitro were successfully anastomosed with the host vasculature upon transplantation in vivo, as shown by immunostaining for human CD31. Collectively, these findings demonstrate that prevascularized, scaffold-free, microtissue spheroids can successfully regenerate vascular dental pulp-like tissue and also highlight the significance of the microtissue microenvironment as an optimal environment for successful pulp-regeneration strategies. © International & American Associations for Dental Research.

  7. Distal C terminus of CaV1.2 channels plays a crucial role in the neural differentiation of dental pulp stem cells.

    Directory of Open Access Journals (Sweden)

    Jianping Ge

    Full Text Available L-type voltage-dependent CaV1.2 channels play an important role in the maintenance of intracellular calcium homeostasis, and influence multiple cellular processes. C-terminal cleavage of CaV1.2 channels was reported in several types of excitable cells, but its expression and possible roles in non-excitable cells is still not clear. The aim of this study was to determine whether distal C-terminal fragment of CaV1.2 channels is present in rat dental pulp stem cells and its possible role in the neural differentiation of rat dental pulp stem cells. We generated stable CaV1.2 knockdown cells via short hairpin RNA (shRNA. Rat dental pulp stem cells with deleted distal C-terminal of CaV1.2 channels lost the potential of differentiation to neural cells. Re-expression of distal C-terminal of CaV1.2 rescued the effect of knocking down the endogenous CaV1.2 on the neural differentiation of rat dental pulp stem cells, indicating that the distal C-terminal of CaV1.2 is required for neural differentiation of rat dental pulp stem cells. These results provide new insights into the role of voltage-gated Ca(2+ channels in stem cells during differentiation.

  8. Use of Coffee Pulp and Minerals for Natural Soil Ameliorant

    Directory of Open Access Journals (Sweden)

    Pujiyanto Pujiyanto

    2007-05-01

    Full Text Available In coffee plantation, solid waste of coffee pulp is usually collected as heap nearby processing facilities for several months prior being used as compost. The practice is leading to the formation of odor and liquid which contaminate the environment. Experiments to evaluate the effect of natural soil ameliorant derived from coffee pulp and minerals were conducted at The Indonesian Coffee and Cocoa Research Institute in Jember, East Java. The experiments were intended to optimize the use of coffee pulp to support farming sustainability and minimize negative impacts of solid waste disposal originated from coffee cherry processing. Prior to applications, coffee pulp was hulled to organic paste. The paste was then mixed with 10% minerals (b/b. Composition of the minerals was 50% zeolite and 50% rock phosphate powder. The ameliorant was characterized for their physical and chemical properties. Agronomic tests were conducted on coffee and cocoa seedling. The experiments were arranged according to Randomized Completely Design with 2 factors, consisted of natural ameliorant and inorganic fertilizer respectively. Natural ameliorant derived from coffee pulp was applied at 6 levels: 0, 30, 60, 90, 120 and 150 g dry ameliorant/seedling of 3 kg soil, equivalent to 0, 1, 2, 3, 4 and 5% (b/b of ameliorant respectively. Inorganic fertilizer was applied at 2 levels: 0 and 2 g fertilizer/application of N-P-K compound fertilizer of 15-15-15 respectively. The inorganic fertilizer was applied 4 times during nursery of coffee and cocoa. The result of the experiment indicated that coffee pulp may be used as natural soil ameliorant. Composition of ameliorant of 90% coffee pulp and 10% of minerals has good physical and chemical characteristics for soil amelioration. The composition has high water holding capacity; cations exchange capacity, organic carbon and phosphorus contents which are favorable to increase soil capacity to support plant growth. Application of

  9. Characterization of Cypress Wood for Kraft Pulp Production

    Directory of Open Access Journals (Sweden)

    António J. A. Santos

    2014-06-01

    Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

  10. Paleoproteomics of the Dental Pulp: The plague paradigm.

    Science.gov (United States)

    Barbieri, Rémi; Mekni, Rania; Levasseur, Anthony; Chabrière, Eric; Signoli, Michel; Tzortzis, Stéfan; Aboudharam, Gérard; Drancourt, Michel

    2017-01-01

    Chemical decomposition and fragmentation may limit the detection of ancient host and microbial DNA while some proteins can be detected for extended periods of time. We applied paleoproteomics on 300-year-old dental pulp specimens recovered from 16 individuals in two archeological funeral sites in France, comprising one documented plague site and one documented plague-negative site. The dental pulp paleoproteome of the 16 teeth comprised 439 peptides representative of 30 proteins of human origin and 211 peptides representative of 27 proteins of non-human origin. Human proteins consisted of conjunctive tissue and blood proteins including IgA immunoglobulins. Four peptides were indicative of three presumable Yersinia pestis proteins detected in 3/8 dental pulp specimens from the plague-positive site but not in the eight dental pulp specimens collected in the plague-negative site. Paleoproteomics applied to the dental pulp is a new and innovative approach to screen ancient individuals for the detection of blood-borne pathogens and host inflammatory response.

  11. Mesta/Kenaf as raw material for Kraft pulping

    Energy Technology Data Exchange (ETDEWEB)

    Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

    1980-03-15

    In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

  12. Pulp tissue in sex determination: A fluorescent microscopic study

    Science.gov (United States)

    Nayar, Amit; Singh, Harkanwal Preet; Leekha, Swati

    2014-01-01

    Aims: To determine and compare the reliability of pulp tissue in determination of sex and to analyze whether caries have any effect on fluorescent body test. Materials and Methods: This study was carried on 50 maxillary and mandibular teeth (25 male teeth and 25 female teeth), which were indicated for extraction. The teeth are categorized into 5 groups, 10 each (5 from males and 5 from females) on the basis of caries progression. The pulp cells are stained with quinacrine hydrochloride and observed with fluorescent microscope for fluorescent body. Gender is determined by identification of Y chromosome fluorescence in dental pulp. Results: Fluorescent bodies were found to be more in sound teeth in males as the caries increase the mean percentage of fluorescent bodies observed decreases in males. We also observed the fluorescent spots in females, and the value of the spot increases in female as the caries progresses, thereby giving false positive results in females. Conclusion: Sex determination by fluorescent staining of the Y chromosome is a reliable technique in teeth with healthy pulps or caries with enamel or up to half way of dentin. Teeth with caries involving pulp cannot be used for sex determination. PMID:25125912

  13. Rice straw pulp obtained by using various methods.

    Science.gov (United States)

    Rodríguez, Alejandro; Moral, Ana; Serrano, Luis; Labidi, Jalel; Jiménez, Luis

    2008-05-01

    Rice straw was used as an alternative raw material to obtain cellulosics pulps. Pulping was done by using classics reagents as soda (with anthraquinone and parabenzoquinone as aditives), potassium hydroxide and Kraft process. The holocellulose, alpha-cellulose and lignin contents of rice straw (viz. 60.7, 41.2 and 21.9 wt%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using soda, soda and anthraquinone at 1 wt%, soda and parabenzoquinone at 1 wt%, potassium hydroxide and sodium sulphate (Kraft process) under two different sets of operating conditions, namely: (a) a 10 wt% reagent concentration, 170 degrees C and 60 min; and (b) 15 wt% reagent, 180 degrees C and 90 min. The solid/liquid ratio was 6 in both cases. Paper sheets made from pulp extracted by cooking with soda (15 wt%) and AQ (1 wt%) at 180 degrees C and 90 min pulp exhibit the best drainage index, breaking length, stretch and burst index (viz. 23 degrees SR, 3494 m, 3.34% and 2.51 kN/g, respectively).

  14. Characterization of active paper packaging incorporated with ginger pulp oleoresin

    Science.gov (United States)

    Wiastuti, T.; Khasanah, L. U.; Atmaka Kawiji, W.; Manuhara, G. J.; Utami, R.

    2016-02-01

    Utilization of ginger pulp waste from herbal medicine and instant drinks industry in Indonesia currently used for fertilizer and fuel, whereas the ginger pulp still contains high oleoresin. Active paper packaging were developed incorporated with ginger pulp oleoresin (0%, 2%, 4%, and 6% w/w). Physical (thickness, tensile strength, and folding endurance, moisture content), sensory characteristics and antimicrobial activity of the active paper were evaluated. Selected active paper then were chemically characterized (functional groups). The additional of ginger pulp oleoresin levels are reduced tensile strength, folding endurance and sensory characteristic (color, texture and overall) and increased antimicrobial activity. Due to physical, sensory characteristic and antimicrobial activity, active paper with 2% ginger pulp oleoresin incorporation was selected. Characteristics of selected paper were 9.93% of water content; 0.81 mm of thickness; 0.54 N / mm of tensile strength; 0.30 of folding endurance; 8.43 mm inhibits the growth of Pseudomonas fluorescence and 27.86 mm inhibits the growth of Aspergillus niger (antimicrobial activity) and neutral preference response for sensory properties. For chemical characteristic, selected paper had OH functional group of ginger in 3422.83 cm-1 of wave number and indicated contain red ginger active compounds.

  15. Secretoneurin and PE-11 immunoreactivity in the human dental pulp.

    Science.gov (United States)

    Steiner, René; Fischer-Colbrie, Reiner; Bletsa, Athanasia; Laimer, Johannes; Troger, Josef

    2018-02-01

    To explore whether there are differences in the concentration of the secretogranin II-derived peptide secretoneurin and the chromogranin B-derived peptide PE-11 between the healthy and inflamed human dental pulps. Furthermore, colocalization studies with calcitonin gene-related peptide were performed to confirm the sensory origin of the peptidergic nerves in the dental pulp. The concentrations of secretoneurin and PE-11 were determined by highly sensitive radioimmunoassays in extracts of dental pulps, the molecular form of secretoneurin immunoreactivities by RP-HPLC with subsequent radioimmunoassay and colocalization studies with calcitonin gene-related peptide were performed by double immunofluorescence. Only secretoneurin but not PE-11 was detectable by radioimmunoassays whereas nerve fibers could be made visible for both secretoneurin and PE-11. Furthermore, there was a full colocalization of secretoneurin and PE-11 with calcitonin gene-related peptide in immunohistochemical experiments. There were no differences in the concentration of secretoneurin between the healthy and inflamed human dental pulp and moreover, the characterization of the secretoneurin immunoreactivities revealed that only authentic secretoneurin was detected with the secretoneurin antibody. There is unequivocal evidence that secretoneurin and PE-11 are constituents of the sensory innervation of the human dental pulp and although not exclusively but are yet present in unmyelinated C-fibers which transmit predominantly nociceptive impulses. Secretoneurin might be involved in local effector functions as well, particularly in neurogenic inflammation, given that this is the case despite of unaltered levels in inflamed tissue. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Dentin and dental pulp regeneration by the patient's endogenous cells.

    Science.gov (United States)

    Kim, Sahng G; Zheng, Ying; Zhou, Jian; Chen, Mo; Embree, Mildred C; Song, Karen; Jiang, Nan; Mao, Jeremy J

    2013-03-01

    The goal of regenerative endodontics is to restore the functions of the dental pulp-dentin complex. Two approaches are being applied toward dental pulp-dentin regeneration: cell transplantation and cell homing. The majority of previous approaches are based on cell transplantation by delivering ex vivo cultivated cells toward dental pulp or dentin regeneration. Many hurdles limit the clinical translation of cell transplantation such as the difficulty of acquiring and isolating viable cells, uncertainty of what cells or what fractions of cells to use, excessive cost of cell manipulation and transportation, and the risk of immune rejection, pathogen transmission, and tumorigenesis in associated with ex vivo cell manipulation. In contrast, cell homing relies on induced chemotaxis of endogenous cells and therefore circumvents many of the difficulties that are associated with cell transplantation. An array of proteins, peptides, and chemical compounds that are yet to be identified may orchestrate endogenous cells to regenerate dental pulp-dentin complex. Both cell transplantation and cell homing are scientifically valid approaches; however, cell homing offers a number of advantages that are compatible with the development of clinical therapies for dental pulp-dentin regeneration.

  17. The annual frequency of root fillings, tooth extractions and pulp-related procedures in Danish adults during 1977-2003

    DEFF Research Database (Denmark)

    Bjørndal, L.; Reit, C.

    2004-01-01

    endodontic epidemiology, frequency of root fillings, pulp capping, stepwise excavation, tooth extractions......endodontic epidemiology, frequency of root fillings, pulp capping, stepwise excavation, tooth extractions...

  18. Amino acid derivative-mediated detoxification and functionalization of dual cure dental restorative material for dental pulp cell mineralization.

    Science.gov (United States)

    Minamikawa, Hajime; Yamada, Masahiro; Iwasa, Fuminori; Ueno, Takeshi; Deyama, Yoshiaki; Suzuki, Kuniaki; Yawaka, Yasutaka; Ogawa, Takahiro

    2010-10-01

    Current dental restorative materials are only used to fill the defect of hard tissues, such as dentin and enamel, because of their cytotoxicity. Therefore, exposed dental pulp tissues in deep cavities must be first covered by a pulp capping material like calcium hydroxide to form a layer of mineralized tissue. However, this tissue mineralization is based on pathological reaction and triggers long-lasting inflammation, often causing clinical problems. This study tested the ability of N-acetyl cysteine (NAC), amino acid derivative, to reduce cytotoxicity and induce mineralized tissue conductivity in resin-modified glass ionomer (RMGI), a widely used dental restorative material having dual cure mechanism. Rat dental pulp cells were cultured on untreated or NAC-supplemented RMGI. NAC supplementation substantially increased the percentage of viable cells from 46.7 to 73.3% after 24-h incubation. Cell attachment, spreading, proliferative activity, and odontoblast-related gene and protein expressions increased significantly on NAC-supplemented RMGI. The mineralization capability of cells, which was nearly suppressed on untreated RMGI, was induced on NAC-supplemented RMGI. These improved behaviors and functions of dental pulp cells on NAC-supplemented RMGI were associated with a considerable reduction in the production of intracellular reactive oxygen species and with the increased level of intracellular glutathione reserves. These results demonstrated that NAC could detoxify and functionalize RMGIs via two different mechanisms involving in situ material detoxification and antioxidant cell protection. We believe that this study provides a new approach for developing dental restorative materials that enables mineralized tissue regeneration.

  19. The prevalence and distribution of radiopaque, calcified pulp stones: A cone-beam computed tomography study in a northern Taiwanese population

    Directory of Open Access Journals (Sweden)

    Chen-Yu Hsieh

    2018-06-01

    Conclusion: Pulp stones are more frequent in maxillary teeth compared to mandibular teeth. Pulp stones in molar teeth were significantly more common than premolars and incisors. CBCT could be a sensitive tool to detect pulp stones, especially simplifying identification of pulp stones in radicular pulp. Knowledge of pulp stones distribution can aid dentists in clinical endodontic treatment.

  20. Characterization of Irreversible Fouling after Ultrafiltration of Thermomechanical Pulp Mill Process Water

    DEFF Research Database (Denmark)

    Thuvander, Johan; Zarebska, Agata; Hélix-Nielsen, Claus

    2018-01-01

    process streams is fouling of the membranes. Fouling not only increases operating costs but also reduces the operating time of the membrane plant. When optimizing the membrane cleaning method, it is important to know which compounds cause the fouling. In this work fouling of an ultrafiltration membrane...... was studied. The fouling propensity of untreated process water and microfiltrated process water was compared. Fouled membranes were analyzed using scanning electron microscopy and attenuated total reflection Fourier transform infrared spectrometry. Acid hydrolysis of membranes exposed to untreated process......Large volumes of wastewater with dissolved wood components are treated in wastewater treatment plants at thermomechanical pulp mills. It has been shown previously that hemicelluloses in these wastewater streams can be recovered by membrane filtration. A serious obstacle when treating lignocellulose...

  1. Wood Pulp Digetster Wall Corrosion Investigation

    Energy Technology Data Exchange (ETDEWEB)

    Giles, GE

    2003-09-18

    The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

  2. Application of thermoalkalophilic xylanase from Arthrobacter sp. MTCC 5214 in biobleaching of kraft pulp

    Digital Repository Service at National Institute of Oceanography (India)

    Khandeparker, R.; Bhosle, N.B.

    released by enzyme treatment showed a characteristic peak at 280 nm indicating the presence of lignin in the released coloring matter. Enzymatic prebleaching of kraft pulp showed 20 % reduction in kappa number of the pulp without much change in viscosity...

  3. Nutritional composition of Annona crassiflora pulp and acceptability of bakery products prepared with its flour

    Directory of Open Access Journals (Sweden)

    Paula Villela

    2013-09-01

    Full Text Available Annona crassiflora offers an edible fruit native to the Savanna. This study aimed to develop a flour meal from Annona crassiflora pulp; analyze the chemical composition of the fresh pulp and its flour; develop and verify the acceptance of formulations with different concentrations of the flour of Annona crassiflora pulp. Fruit used were selected and processed. The pulp was dried in an oven at 60-65 ºC/48h. We analyzed the chemical composition, and two formulations of breads were prepared with 10 and 20% Annona crassiflora pulp. The results showed that the drying of Annona crassiflora pulp enriched its nutritional value. The Annona crassiflora pulp showed important chemical components, as insoluble fibers (pulp and flour, minerals (potassium, calcium, manganese and others and antioxidant compounds. The formulations were well-accepted in a sensory point of view and proved to be a good alternative to the exploitation of the fruit.

  4. Advanced Scaffolds for Dental Pulp and Periodontal Regeneration.

    Science.gov (United States)

    Bottino, Marco C; Pankajakshan, Divya; Nör, Jacques E

    2017-10-01

    No current therapy promotes root canal disinfection and regeneration of the pulp-dentin complex in cases of pulp necrosis. Antibiotic pastes used to eradicate canal infection negatively affect stem cell survival. Three-dimensional easy-to-fit antibiotic-eluting nanofibers, combined with injectable scaffolds, enriched or not with stem cells and/or growth factors, may increase the likelihood of achieving predictable dental pulp regeneration. Periodontitis is an aggressive disease that impairs the integrity of tooth-supporting structures and may lead to tooth loss. The latest advances in membrane biomodification to endow needed functionalities and technologies to engineer patient-specific membranes/constructs to amplify periodontal regeneration are presented. Copyright © 2017 Elsevier Inc. All rights reserved.

  5. Electron treatment of wood pulp for the viscose process

    Science.gov (United States)

    Stepanik, T. M.; Ewing, D. E.; Whitehouse, R.

    2000-03-01

    Electron processing is currently being evaluated by several viscose producers for integration into their process. The viscose industry converts dissolving wood pulp into products such as staple fibre, filament, cord, film, packaging, and non-edible sausage casings. These materials are used in the clothing, drapery, hygiene, automobile, food, and packaging industries. Viscose producers are facing increasingly high production costs and stringent environmental regulations that have forced some plants to close. Electron treatment of wood pulp can significantly reduce the amounts of chemicals used for producing viscose and the production of hazardous pollutants. Acsion Industries has worked with companies worldwide to demonstrate the benefits of using electron treated pulp for producing viscose (rayon). This paper describes the viscose process, the benefits of using electron treatment in the viscose process, and Acsion's efforts in developing this technology.

  6. Magnet options for sensors for the pulp and paper industry

    International Nuclear Information System (INIS)

    Green, M.A.; Barale, P.J.; Fong, C.G.; Luft, P.A.; Reimer, J.A.; Yahnke, M.S.

    2001-01-01

    The Lawrence Berkeley National Laboratory (LBNL) has been developing sensors for the pulp and paper industry that uses a magnetic field. The applications for magnetic sensors that have studied include (1) sensors for the measurement of the water and ice content of wood chips entering the pulping mill, (2) sensors for measuring the water content and other constituents of the black liquor leaving the paper digester, and (3) sensors for measuring paper thickness and water content as the paper is being processed. These tasks can be done using nuclear magnetic resonance (NMR). The magnetic field used for doing the NMR can come from either permanent magnets or superconducting magnets. The choice of the magnet is dependent on a number of factors, which include the size of the sample and field strength needed to do the sensing task at hand. This paper describes some superconducting magnet options that can be used in the pulp and paper industry.

  7. Engineering structural integrity issues in the pulp and paper industry

    International Nuclear Information System (INIS)

    Garner, A.; Singbeil, D.

    2002-01-01

    ESI issues for Pulp and Paper (P and P) plant are reviewed. Five typical processes are covered, namely: Chemical Pulping, Bleaching, Chemical Recovery, Mechanical Pulping and Papermaking. Equipment, chemical environments and failure modes are summarized with examples from each process. Pressure, temperature, corrosion and rotation are typical sources of risk, which is managed by appropriate inspection. The nature of the P and P Industry and its technology supply is summarized: current trends are consolidation and outsourcing. Three examples are presented to illustrate typical ESI issues: deaerator cracking where the P and P Industry alerted others to this serious cross-industry problem; pressure vessel safety factors and inconsistent international codes; and caustic cracking in continuous kraft digesters, which required rapid and concerted action to diagnose and control. In the future better predictability, data-bases, more formal risk based inspection and fitness-for-service assessments are envisaged. (author)

  8. Outcomes of Different Vital Pulp Therapy Techniques on Symptomatic Permanent Teeth: A Case Series

    OpenAIRE

    Asgary, Saeed; Fazlyab, Mahta; Sabbagh, Sedigheh; Eghbal, Mohammad Jafar

    2014-01-01

    In modern endodontics, vital pulp therapy (VPT) has been considered an ultra-conservative treatment modality. Based on the level of pulp preservation, VPT includes stepwise excavation, indirect pulp capping (IDPC), direct pulp capping (DPC), miniature pulpotomy (MP), partial/Cvek pulpotomy and coronal/complete pulpotomy (CP). The present article reviews the treatment outcomes of 94 permanent teeth with irreversible pulpitis treated with either IDPC (n=28), DPC (n=28), MP (n=29) or CP (n=9) us...

  9. Anthraquinone-A Review of the Rise and Fall of a Pulping Catalyst

    Science.gov (United States)

    Peter W. Hart; Alan W. Rudie

    2014-01-01

    The application of anthraquinone (AQ) as a pulping catalyst has been well documented in scientific studies and mill applications. AQ is known to increase the rate of delignification, enabling a reduction in pulping time, temperature, or chemical charge and an increase in pulp yield. Specific details of AQ use are not extensively reviewed in this work. The review...

  10. Studies of lignin transformation in polyoxometalate (POM) bleaching of kraft pulp

    Science.gov (United States)

    Biljana Bujanovic; Richard S. Reiner; Kolby C. Hirth; Sally A. Ralph; Rajai H. Atalla

    2005-01-01

    In order to elucidate changes occurring in lignin during polyoxometalate delignification of kraft pulp, residual lignins of a series of POM- delignified kraft pulps of decreasing kappa number were isolated and characterized. Oxidative treatment of commercial unbleached kraft pulp was performed using complex POM solutions containing the active [SiVW11O40]anion. For...

  11. Alkaline Pulping and Bleaching of Acacia auriculiformis Grown in Bangladesh

    OpenAIRE

    JAHAN, M. Sarwar; SABINA, Rowshan; RUBAIYAT, Arjumand

    2014-01-01

    The physical, chemical, and morphological characteristics of Acacia auriculiformis were evaluated in terms of its suitability for papermaking. The fiber length (1.1 mm) of A. auriculiformis in this study was within the range of tropical hardwoods. The lignin content in A. auriculiformis was 19.4% and a-cellulose 44.1%, which was within the range of other acacias, but that of extractives was higher. Soda, soda-AQ, and kraft processes were studied in pulping. Screened pulp yield was increased w...

  12. Pre-treatment and ethanol fermentation potential of olive pulp at different dry matter concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Haagensen, Frank [Bioprocess Science and Technology group, Biocentrum-DTU, Building 227, Technical University of Denmark, 2800 Lyngby (Denmark); Skiadas, Ioannis V.; Gavala, Hariklia N.; Ahring, Birgitte K. [Bioprocess Science and Technology group, Biocentrum-DTU, Building 227, Technical University of Denmark, 2800 Lyngby (Denmark); Copenhagen Institute of Technology (Aalborg University Copenhagen), Section for Sustainable Biotechnology, Department of Biotechnology, Chemistry and Environmental Engineering, Lautrupvang 15, DK 2750 Ballerup (Denmark)

    2009-11-15

    Renewable energy sources have received increased interest from the international community with biomass being one of the oldest and the most promising ones. In the concept of exploitation of agro-industrial residues, the present study investigates the pre-treatment and ethanol fermentation potential of the olive pulp, which is the semi solid residue generated from the two-phase processing of the olives for olive oil production. Wet oxidation and enzymatic hydrolysis have been applied aiming at the enhancement of carbohydrates' bioavailability. Different concentrations of enzymes and enzymatic durations have been tested. Both wet oxidation and enzymic treatment were evaluated based on the ethanol obtained in a subsequent fermentation step by Saccharomyces cerevisiae and Thermoanaerobacter mathranii. It was found that a four-day hydrolysis time was adequate for a satisfactory release of glucose and xylose. The combination of wet oxidation and enzymatic hydrolysis resulted in the glucose and xylose concentration increase of 138 and 444%, respectively, compared to 33 and 15% with only enzymes added. However, the highest ethanol production was obtained when only enzymic pre-treatment was applied, implying that wet oxidation is not a recommended pre-treatment process for olive pulp at the conditions tested. It was also showed that increased dry matter concentration did not have a negative effect on the release of sugars, indicating that the cellulose and xylan content of the olive pulp is relatively easily available. The results of the experiments in batch processes clearly emphasize that the simultaneous saccharification and fermentation (SSF) mode is advantageous in comparison with the separate hydrolysis and fermentation (SHF) mode concerning process contamination. (author)

  13. Nutritional Value of Tamarindus Indica Fruit Pulp

    International Nuclear Information System (INIS)

    Chiteva, R.; Kitui, J.L

    2007-01-01

    In Kenya Tamarindus Indica (Tamarind) fruits are not fully utilized despite their abundance in Nyanza, Rift Valley and Eastern provinces. This study determined the nutritional composition of the edible fruit pulp to enhance utilization. The edible portion of Tamarindus indica fruit ('Ukwaju' in Kiswahili) was analysed for it's chemical and nutritional composition. The fruit was sampled from Kitui, Mwingi and Makueni districts of Ukambani, with an assumption that they could be climatically different. The analysis carried out included moisture content, sulphated ash, Vitamin C content, crude protein and minerals namely Na, Ca, Mg, Fe, Zn, Cu and Mn. The energy contents were determined and total carbohydrates calculated. The results showed very low protein content of 0.01% for Kvisuni and Makindu divisions, while Katse and Kyanundu in Mwingi and TARDA in Makueni districts gave the highest value of 0.02% . This is a fairly low protein content compared with other indigenous fruits like Andasonia digitata (Baobab) with a value of 2.9%. The fat content was also low, especially for Makueni that had a value of 0.04% for the unripe fruits while Mwingi gave 0.04% for those fruits that were ripe. Vitamin C content was similar for the fruit from the three districts (8mg100g-1 ) sample. The fruits also contained an appreciable high internal energy level with Mbitini recording highest at 2.94 kcal. All samples had levels of Fe above 1mg100g-1 . Sodium was also available in all samples with TARDA sample having the highest (0.8mg/100g-1 ) . Potassium values were over 200 mg100g-1 s ample for all samples with TARDA leading (1050 mg100g-1 ) . Calcium in all samples was over 20 mg100g-1 w hile mg was 30 mg100g-1 w ith Makindu having the highest value of 75.2mg100g-1 . This fruit, therefore has the potential of providing nutrients and can be used as a food supplement

  14. Microarray evaluation of gene expression profiles in inflamed and healthy human dental pulp: the role of IL1beta and CD40 in pulp inflammation.

    Science.gov (United States)

    Gatta, V; Zizzari, V L; Dd ' Amico, V; Salini, L; D' Aurora, M; Franchi, S; Antonucci, I; Sberna, M T; Gherlone, E; Stuppia, L; Tetè, S

    2012-01-01

    Dental pulp undergoes a number of changes passing from healthy status to inflammation due to deep decay. These changes are regulated by several genes resulting differently expressed in inflamed and healthy dental pulp, and the knowledge of the processes underlying this differential expression is of great relevance in the identification of the pathogenesis of the disease. In this study, the gene expression profile of inflamed and healthy dental pulps were compared by microarray analysis, and data obtained were analyzed by Ingenuity Pathway Analysis (IPA) software. This analysis allows to focus on a variety of genes, typically expressed in inflamed tissues. The comparison analysis showed an increased expression of several genes in inflamed pulp, among which IL1β and CD40 resulted of particular interest. These results indicate that gene expression profile of human dental pulp in different physiological and pathological conditions may become an useful tool for improving our knowledge about processes regulating pulp inflammation.

  15. Papaya pulp gelling: is it premature ripening or problems of water accumulation in the apoplast?

    Directory of Open Access Journals (Sweden)

    Jurandi Gonçalves de Oliveira

    Full Text Available Gelled aspect in papaya fruit is typically confused with premature ripening. This research reports the characterization of this physiological disorder in the pulp of papaya fruit by measuring electrolyte leakage, Pi content, lipid peroxidation, pulp firmness, mineral contents (Ca, Mg and K - in pulp and seed tissues, and histological analysis of pulp tissue. The results showed that the gelled aspect of the papaya fruit pulp is not associated with tissue premature ripening. Data indicate a reduction of the vacuole water intake as the principal cause of the loss of cellular turgor; while the waterlogged aspect of the tissue may be due to water accumulation in the apoplast.

  16. Vital pulp therapy in symptomatic immature permanent molars: Report of 3 cases

    Directory of Open Access Journals (Sweden)

    SheikhRezaie MS.

    2009-11-01

    Full Text Available "nEndodontic treatment of immature permanent teeth accompanies with several issues. The primary goal when treating such teeth is to maintain pulp vitality so that root development can occur normally. Indications and requirements for vital pulp therapy include asymptomatic and reversible pulpitis. Also there are controversial opinions regarding the ultimate clinical treatment of the vital pulp therapy techniques. In this manuscript we report 3 cases of immature symptomatic permanent molars with irreversible pulpitis caused by caries exposure of the pulp that have been undergone vital pulp therapy successfully.

  17. Recuperation of uranium and gold in mineral pulps by adsorption

    International Nuclear Information System (INIS)

    Bruno, J.B.; Amorim, L.O.

    1985-06-01

    The technological routes for the treatment of the gold and uranium ores are presented. The results obtained during the continuous tests with the uraniferous Ores of Wabo in Somalia are presented. The utilization of 99% of the uranium content in the alkaline pulp is obtained. (C.B.) [pt

  18. Pequi pulp ( Caryocar brasiliense Cambess): Drying kinetics and ...

    African Journals Online (AJOL)

    The entropy values found were -251.01, -250.38 and -250.05 (J.Mol-1K-1) for the same temperatures. The values obtained from the Gibbs free energy for the drying of Pequi pulp increased with increasing temperature. The obtained data were consistent to the drying process, and the mathematical equations were effective ...

  19. Incidence and Distribution of Pulp Stones Found in Radiographic ...

    African Journals Online (AJOL)

    or more in a single tooth, their size varying from minute particles to large masses ... between pulp stones and sex, tooth type, dental arch, side and .... attended Kırıkkale University Dental School (KUDS).Caution .... Beside these disadvantages,.

  20. Comparison of various pulping characteristic of Fraxinus angustifolia ...

    African Journals Online (AJOL)

    Handsheets made from different pulping methods were compared with each other for strength and optical properties. Strength properties were found to be higher for kraft and kraft + anthraquinone processes, while optical properties were found to be higher for cold soda and NSSC processes. Key words: Ash, Fraxinus ...

  1. Enzymatic modification of pectic polysaccharides obtained from sugar beet pulp

    NARCIS (Netherlands)

    Oosterveld, A.; Beldman, G.; Voragen, A.G.J.

    2002-01-01

    Rhamnogalacturonans and arabinans, purified from an autoclave extract of sugar beet pulp, as well as an acid extracted beet pectin (ABP) were treated with enzymes in order to modify their physico-chemical properties. The enzymes used were arabinofuranosidase B (AF), endo-arabinanase plus

  2. 21 CFR 176.260 - Pulp from reclaimed fiber.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Pulp from reclaimed fiber. 176.260 Section 176.260 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS Substances...

  3. Fourier Transform Infrared Imaging analysis of dental pulp inflammatory diseases.

    Science.gov (United States)

    Giorgini, E; Sabbatini, S; Conti, C; Rubini, C; Rocchetti, R; Fioroni, M; Memè, L; Orilisi, G

    2017-05-01

    Fourier Transform Infrared microspectroscopy let characterize the macromolecular composition and distribution of tissues and cells, by studying the interaction between infrared radiation and matter. Therefore, we hypothesize to exploit this analytical tool in the analysis of inflamed pulps, to detect the different biochemical features related to various degrees of inflammation. IR maps of 13 irreversible and 12 hyperplastic pulpitis, together with 10 normal pulps, were acquired, compared with histological findings and submitted to multivariate (HCA, PCA, SIMCA) and statistical (one-way ANOVA) analysis. The fit of convoluted bands let calculate meaningful band area ratios (means ± s.d., P < 0.05). The infrared imaging analysis pin-pointed higher amounts of water and lower quantities of type I collagen in all inflamed pulps. Specific vibrational markers were defined for irreversible pulpitis (Lipids/Total Biomass, PhII/Total Biomass, CH 2 /CH 3 , and Ty/AII) and hyperplastic ones (OH/Total Biomass, Collagen/Total Biomass, and CH 3 Collagen/Total Biomass). The study confirmed that FTIR microspectroscopy let discriminate tissues' biological features. The infrared imaging analysis evidenced, in inflamed pulps, alterations in tissues' structure and composition. Changes in lipid metabolism, increasing amounts of tyrosine, and the occurrence of phosphorylative processes were highlighted in irreversible pulpitis, while high amounts of water and low quantities of type I collagen were detected in hyperplastic samples. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Relaxant effect of Lagenaria breviflora Roberty fruit pulp and seeds ...

    African Journals Online (AJOL)

    Lagenaria breviflora roberty is used in West Africa as traditional remedy for treatment of gastrointestinal disorders, particularly diarrhoea. This study was aimed at assessing the effect of the pulp and seed extract of L. breviflora on the contractile activity of isolated rabbit ileum. Rabbits of both sexes were used for the study ...

  5. Mechanical pulping with a sequential velocity refiner- a new concept

    Science.gov (United States)

    C.W. McMillin

    1978-01-01

    In previous research with refiner mechanical pulps, a theoretical stress analysis indicated that longitudinal tracheids of Pinus taeda L. fail while under torsional stress and unwind into ribbonlike elements that provide the coherence necessary for strength development. When macerated tracheids of loblolly pine were individually stressed in torsion...

  6. Catalase activity in healthy and inflamed pulp tissues of permanent ...

    African Journals Online (AJOL)

    Aim: To evaluate catalase (CAT, EC 1.11.1.6) activity in healthy and inflamed dental pulp of young patient's teeth and to investigate if an active defense system oxidizing agents is present as a response to bacterial invasion. Materials and Methods: Twenty young patients between 15 and 25 ages, who were diagnosed to be ...

  7. Antimicrobial screening and effect of the pulp extracts of Zizyphus ...

    African Journals Online (AJOL)

    Groups of rats were orally administered 200mg/kg, 400mg/kg and 800mg/kg body weight of extracts daily for three (3) weeks. The animals were sacrificed by decapitation and blood collected for biochemical analysis. The pulp aqueous extract showed more susceptibility on E. coli, P. aeruginosa and C. albicans which is a ...

  8. Assessment of Antioxidant Properties of Tamarind Fruit Pulp and its ...

    African Journals Online (AJOL)

    Both seed dhal and flour treated with tamarind fruit pulp had lower mean TBA values ranging from 2.80 to 4.12 ppm Malonaldehyde as against 4.55 to 4.91 ppm for untreated samples. Tamarind fruit can thus be further studied for possible exploitation as a natural antioxidant for use in food, drug and cosmetic products.

  9. Incidence and Distribution of Pulp Stones Found in Radiographic ...

    African Journals Online (AJOL)

    The overall incidence of pulp stones in the patients and their correlations between female and male patients and between the right‑side and left‑side occurrences were analyzed by computer program, SPSS 15. (SPSS Inc. Chicago, USA) with using the χ2 test. Differences were considered as significant when P < 0.05.

  10. Sequenced anaerobic - aerobic treatment of hemp pulping wastewaters

    NARCIS (Netherlands)

    Kortekaas, S.

    1998-01-01

    Biological treatment is an indispensable instrument for water management of non-wood pulp mills, either as internal measure to enable progressive closure of water cycles, or as end of pipe treatment. In this thesis, the sequenced anaerobic-aerobic treatment of hemp ( Cannabis

  11. Allogenic banking of dental pulp stem cells for innovative therapeutics.

    Science.gov (United States)

    Collart-Dutilleul, Pierre-Yves; Chaubron, Franck; De Vos, John; Cuisinier, Frédéric J

    2015-08-26

    Medical research in regenerative medicine and cell-based therapy has brought encouraging perspectives for the use of stem cells in clinical trials. Multiple types of stem cells, from progenitors to pluripotent stem cells, have been investigated. Among these, dental pulp stem cells (DPSCs) are mesenchymal multipotent cells coming from the dental pulp, which is the soft tissue within teeth. They represent an interesting adult stem cell source because they are recovered in large amount in dental pulps with non-invasive techniques compared to other adult stem cell sources. DPSCs can be obtained from discarded teeth, especially wisdom teeth extracted for orthodontic reasons. To shift from promising preclinical results to therapeutic applications to human, DPSCs must be prepared in clinical grade lots and transformed into advanced therapy medicinal products (ATMP). As the production of patient-specific stem cells is costly and time-consuming, allogenic biobanking of clinical grade human leukocyte antigen (HLA)-typed DPSC lines provides efficient innovative therapeutic products. DPSC biobanks represent industrial and therapeutic innovations by using discarded biological tissues (dental pulps) as a source of mesenchymal stem cells to produce and store, in good manufacturing practice (GMP) conditions, DPSC therapeutic batches. In this review, we discuss about the challenges to transfer biological samples from a donor to HLA-typed DPSC therapeutic lots, following regulations, GMP guidelines and ethical principles. We also present some clinical applications, for which there is no efficient therapeutics so far, but that DPSCs-based ATMP could potentially treat.

  12. Measurement of cellulose content, Kraft pulp yield and basic density ...

    African Journals Online (AJOL)

    Previous descriptions of multisite and multispecies near infra-red (NIR) spectroscopic calibrations for predicting cellulose content (CC) and Kraft pulp yield (KPY) in eucalypt woodmeal demonstrated that large, single calibrations provide precise predictions for a wide range of sites and species. These have since been used ...

  13. Natural and recombinant fungal laccases for paper pulp bleaching

    NARCIS (Netherlands)

    Sigoillot, C.; Record, E.; Belle, V.; Robert, J.L.; Levasseur, A.; Punt, P.J.; Hondel, C.A.M.J.J. van den; Fournel, A.; Sigoillot, J.C.; Asther, M.

    2004-01-01

    Three laccases, a natural form and two recombinant forms obtained from two different expression hosts, were characterized and compared for paper pulp bleaching. Laccase from Pycnoporus cinnabarinus, a well known lignolytic fungus, was selected as a reference for this study. The corresponding

  14. Possible mechanism for anthraquinone species diffusion in alkaline pulping

    Science.gov (United States)

    X.-S. Chai; J. Samp; Q.X. Hou; S.-H Yoon; J.Y. Zhu

    2007-01-01

    An analysis of the effectiveness of anthraquinone (AQ) in kraft-AQ pulping in terms of its mechanism of transport has been conducted. Our previous work showed that caustic solutions of wood lignin can decrease the membrane exclusion for anthraquinones, i.e., the presence of wood lignin enhances the ability of AQ to pass through a membrane when a reducing agent is...

  15. CD44 is involved in mineralization of dental pulp cells.

    Science.gov (United States)

    Chen, Kuan-Liang; Huang, Yu-Yuan; Lung, Jrhau; Yeh, Ying-Yi; Yuan, Kuo

    2013-03-01

    CD44 is a transmembrane glycoprotein with various biological functions. Histologic studies have shown that CD44 is strongly expressed in odontoblasts at the appositional stage of tooth development. We investigated whether CD44 is involved in the mineralization of dental pulp cells. Ten human third molars with incomplete root formation were collected and processed for immunohistochemistry of CD44. Dental pulp cells isolated from another 5 human third molars were assayed for their viability, alkaline phosphatase activity, and alizarin red staining in vitro after silencing stably their expression of CD44 by using the short hairpin RNA technique. The CD44 knockdown cells were cultured on a collagen sponge and transplanted subcutaneously into the dorsal surfaces of immunocompromised mice. After 6 weeks, the subcutaneous tissues were processed for alizarin red staining and immunohistochemistry of human specific antigen. The dental pulp cells transduced with control short hairpin RNA were used as the control in all assays. CD44 is expressed in odontogenic cells with active mineral deposition during tooth development. Odontoblasts in the root ends of immature teeth express a stronger CD44 signal compared with those in the crown portion. When CD44 expression was stably suppressed in dental pulp cells, their mineralization activities were substantially decreased in both in vitro and in vivo assays. CD44 may play a crucial role in the initial mineralization of tooth-associated structures. However, further studies are required to clarify the underlying mechanisms. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  16. Pulp antioxidant activities, mineral contents and juice nutritional ...

    African Journals Online (AJOL)

    Statistical differences among the citrus pulps were established for the contents of phenols, flavonoids and carotenoids, the quantification of bioactive compounds revealed distinct contents amongst the analysed materials. Phenolic and flavonoid contents presented a value between 3108.78 and 4046.20 mg gallic acid/100 g ...

  17. Fatty acids profile of pulp and nuts of Brazilian fruits

    Directory of Open Access Journals (Sweden)

    Paulo Afonso da Costa

    2011-12-01

    Full Text Available Fruits and nuts from the North and Northeast regions of Brazil were collected to determine the fatty acid profile of their oils. The species studied were Brazil (Bertholletia excelsa H.B.K., Mucajá (Couma rigida M., Inajá (Maximiliana maripa D., Jenipapo (Genipa Americana L., and Buriti (Mauritia flexuosa L. nuts. Fatty acid methyl esters were analyzed by gas chromatography with flame ionization detection (GC-FID. Brazil nut major fatty acid was 18:3n-3 (α-linolenic acid, and Buriti nut had approximately 23 times more 18:3n-3 than the pulp. Mucajá nut presented high content of 12:0 (lauric acid and 16:0 (palmitic acid, and Mucajá pulp showed significant levels of 18:2n-6 (linoleic acid. Considering the PUFA (polyunsaturated fatty acid sum values, almost all fruits and nuts analyzed presented very high levels of these compounds. Regarding n-6/n-3 ratio, only Brazil Nut, Buriti Nut, Inajá pulp, and Jenipapo pulp corresponded to the desired profile. These Brazilian fruits and nuts could be of potential interest due to their high nutritive value and lipid content.

  18. RE-UTILIZATION OF INORGANIC SOLID WASTE (LIME MUD AS FOREST ROAD STABILIZER FROM THE CHEMICAL RECOVERY PROCESS IN KRAFT PULP MILL

    Directory of Open Access Journals (Sweden)

    Habip Eroğlu

    2005-04-01

    Full Text Available Waste handling is a concern in all pulp and paper mills. Best available techniques for reducing waste is to minimize the generation of solid waste and/or reuse these materials, wherever practicable. One of the most important solid wastes is lime mud which is generated from the kraft pulping in its chemical recovery process. This paper explores the composition of lime mud resulting from the chemical recovery unite of kraft pulp mill and investigation of this waste for re-using beneficially on sub grade and pavement of forest road as a alternative disposal method. Lime mud obtained from the re-causticising process in SEKA pulp mill that utilizes wheat straw and reed as the principal raw material was supplied with % 47 water content and its chemical and physical characterisations was performed according to standard methods. Dried waste to environmental condition was mixed with certain amount to composite cement for using on pavement and sandy clay, loamy clay and clay soils for enriching forest road sub grade properties. In order to investigate the lime mud addition on pavement and sub grade properties necessary physical tests were performed. As a consequence this study reveals that while waste of lime mud causes environmental and economical problem with conventional disposal techniques and/or abandoning to environment, this waste can be used as good stabilisation materials on forest road sub-grade and pavement without any environmental problem.

  19. Determining the minimum conditions for soda-anthraquinone pulping of kenaf bast, core, and whole stalk fibers

    Science.gov (United States)

    James S. Han; Thomas A. Rymsza

    1999-01-01

    Chemical pulping of kenaf fiber is comparatively new. In this study, bast, core, and whole stalk kenaf fibers were pulped using a soda-AQ pulping process and various pulping conditions. Handsheets were evaluated for density, Canadian standard freeness, brightness, opacity, smoothness, and tensile, burst, and tear indexes and strength. The results indicate that...

  20. Swedish Pulp Mill Biorefineries. A vision of future possibilities

    Energy Technology Data Exchange (ETDEWEB)

    Berntsson, Thore (Chamers Univ. of Technology, Goeteborg (Sweden)); Axegaard, Peter; Backlund, Birgit; Samuelsson, Aasa; Berglin, Niklas; Lindgren, Karin (STFI-Packforsk, Stockholm (Sweden))

    2008-07-01

    Today, modern science could make it possible to develop techniques for refining almost the whole wood-matter, pulp mill side streams and bark compounds into platform chemicals, electricity, high quality fuels and structured feed-stock for chemicals and materials. The major challenge is to convert the state of basic scientific knowledge into industrial practise. Our definition of an integrated biorefinery is: 'Full utilization of the incoming biomass and other raw materials for simultaneous and economically optimized production of fibres, chemicals and energy'. Examples of products from a pulp mill biorefinery are: Chemicals and Materials (Phenols, adhesives, carbon fibres, activated carbon, binders, barriers, adhesives, antioxidants, surfactants, chelants, solvents, adhesives surfactants, descaling agents, specialty polymers, pharmaceuticals, nutraceuticals, cosmetics etc., Biofuels (pellets, lignin fuel, methanol, DME, ethanol etc), Electricity (BLGCC, condensing power etc.). The new or increased amounts of traditional products can be made from internal and/or external biomass. Three different levels can be identified: A high degree of energy saving in future mills, especially chemical pulp mills, will lead to large amounts of excess internal biomass which can be transferred to products mentioned above, Components in e.g. the black liquor, forest residues and bark can be upgraded to more valuable ones and the energy balance of the mill is kept through fuel import, wholly or partly depending on the level of mill energy efficiency. This imported fuel can be biomass or other types. External (imported) biomass (in some cases together with excess internal biomass) can be upgraded using synergy effects of docking this upgrading to a pulp mill. Electricity has been included as one of the possible biorefinery products. The electricity production in a mill can be increased in several ways which cannot be directly considered as biorefineries, e.g. recovery boiler

  1. Assessment of oxygen saturation in dental pulp of permanent teeth with periodontal disease.

    Science.gov (United States)

    Giovanella, Larissa Bergesch; Barletta, Fernando Branco; Felippe, Wilson Tadeu; Bruno, Kely Firmino; de Alencar, Ana Helena Gonçalves; Estrela, Carlos

    2014-12-01

    In individuals with periodontal disease, dental pulp status should be determined before a treatment plan is made. Pulse oximeters are promising diagnostic tools to evaluate pulp vascularization. This study used pulse oximetry to determine the level of oxygen saturation in dental pulp of intact permanent teeth with periodontal attachment loss (PAL) and gingival recession (GR) and to evaluate the correlation between periodontal disease and level of oxygen saturation in the pulp. This study included 67 anterior teeth of 35 patients; all teeth showed intact crowns, PAL, a periodontal pocket (PP), and GR. The teeth underwent periodontal examination, cold and electric pulp testing, and pulse oximetry measurements. The Pearson correlation coefficient and a linear regression coefficient were calculated to evaluate the degree of correlation between periodontal disease markers (PAL, PP, and GR) and the level of oxygen saturation in dental pulp. These tests also evaluated possible associations between oxygen saturation and cold and electric pulp testing. PAL, PP, and GR had negative correlations with oxygen saturation in dental pulp. Conversely, no statistically significant association was found between oxygen saturation in dental pulp and the response to electric sensibility testing. Oxygen saturation was lower in the pulp of permanent teeth with PAL, PP, and GR, indicating that periodontal disease correlates with the level of oxygen saturation in the pulp. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  2. Idiopathic dental pulp calcifications in a tertiary care setting in South India.

    Science.gov (United States)

    Satheeshkumar, P S; Mohan, Minu P; Saji, Sweta; Sadanandan, Sudheesh; George, Giju

    2013-01-01

    Dental pulp calcifications are unique and represent the dental pulp regenerative process. Dental pulp calcifications are sometimes routine findings in oral radiographs and may later serve as an important diagnostic criterion for a hidden aspect of systemic illness. The purpose of this study was to assess the patterns and prevalence of idiopathic dental pulp calcifications in a tertiary care setting in South India. A total of 227 patients were included in the study fulfilling the inclusion criteria. Age range of the study population was from 15 to 70 years. Teeth were examined under digital panoramic radiograph. The presence or absence of pulp stones was recorded. The presence of pulp stone were categorized according to the types classified as Type I, Type IA, Type II, Type IIA, Type II B, and Type III. The frequency of occurrence of pulp stones with sex, tooth type, dental arches, and types were compared with the types of calcification. Total no. of patients with pulpal calcification were 227 [females 133 (58.59%) and males 94 (41.40%)]. The most common type between both sexes was Type I (48%). Total no. of teeth with calcification was 697; maxilla (48%), mandible (52%). The prevalence of pulp stone was found to be higher in the molars in both the arches. Most no. of pulp stones are reported at the third and fourth decade of life. Idiopathic dental pulp calcifications are incidental radiographic findings of the pulp tissue and also may be an indicator of underlying disease.

  3. Human tooth pulp anatomy visualization by 3D magnetic resonance microscopy

    International Nuclear Information System (INIS)

    Sustercic, Dusan; Sersa, Igor

    2012-01-01

    Precise assessment of dental pulp anatomy is of an extreme importance for a successful endodontic treatment. As standard radiographs of teeth provide very limited information on dental pulp anatomy, more capable methods are highly appreciated. One of these is 3D magnetic resonance (MR) microscopy of which diagnostic capabilities in terms of a better dental pulp anatomy assessment were evaluated in the study. Twenty extracted human teeth were scanned on a 2.35 T MRI system for MR microscopy using the 3D spin-echo method that enabled image acquisition with isotropic resolution of 100 μm. The 3D images were then post processed by ImageJ program (NIH) to obtain advanced volume rendered views of dental pulps. MR microscopy at 2.35 T provided accurate data on dental pulp anatomy in vitro. The data were presented as a sequence of thin 2D slices through the pulp in various orientations or as volume rendered 3D images reconstructed form arbitrary view-points. Sequential 2D images enabled only an approximate assessment of the pulp, while volume rendered 3D images were more precise in visualization of pulp anatomy and clearly showed pulp diverticles, number of pulp canals and root canal anastomosis. This in vitro study demonstrated that MR microscopy could provide very accurate 3D visualization of dental pulp anatomy. A possible future application of the method in vivo may be of a great importance for the endodontic treatment

  4. The effects of high energy radiation on the pulping properties of Pinus radiation and Eucalyptus regnans

    International Nuclear Information System (INIS)

    McLaren, K.G.; Garland, C.P.; Higgins, H.G.

    1976-01-01

    Studies have been made of the effects of high energy radiation on the pulping behaviour of Eucalyptus regnans and Pinus radiata. Pre-irradiation of wood chips with small doses of 60 Co gamma radiation (up to about 0.2 Mrad) caused little degradation of the cellulose, and had only minor effects on the kraft pulping properties of both wood species. Pulp yield, Kappa number and strength properties of the pulps showed little change. There was also little effect on the bisulphite cooking of Pinus radiata. As the dose was increased to 1 Mrad, degradation of cellulose (as indicated by degree of polymerisation measurements) became significant, and Kraft pulp yields from both woods showed small reductions. The Kappa number and physical properties of these pulps were little affected at this dose level. A gamma radiation dose of 10 Mrad produced marked depolymerisation of the cellulose, and big reductions in kraft and neutral sulphite semi-chemical pulp yields. The kraft pulps showed a much higher lignin content. Some low dose (0.15 Mrad) irradiations on thin chips were carried out with a 1 MeV electron accelerator. In contrast to comparable gamma irradiations, this treatment produced discernible changes in kraft pulping behaviour. The pulp yield, under the same cooking conditions, appears to be slightly higher, but the Lignin content of the pulp was increased. (Author)

  5. Tropical Fruit Pulps: Processing, Product Standardization and Main Control Parameters for Quality Assurance

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo de Farias Silva

    2017-05-01

    Full Text Available ABSTRACT Fruit pulp is the most basic food product obtained from fresh fruit processing. Fruit pulps can be cold stored for long periods of time, but they also can be used to fabricate juices, ice creams, sweets, jellies and yogurts. The exploitation of tropical fruits has leveraged the entire Brazilian fruit pulp sector due mainly to the high acceptance of their organoleptic properties and remarkable nutritional facts. However, several works published in the last decades have pointed out unfavorable conditions regarding the consumption of tropical fruit pulps. This negative scenario has been associated with unsatisfactory physico-chemical and microbiological parameters of fruits pulps as outcomes of little knowledge and improper management within the fruit pulp industry. There are protocols for delineating specific identity and quality standards (IQSs and standardized good manufacturing practices (GMP for fruit pulps, which also embrace standard operating procedures (SOPs and hazard analysis and critical control points (HACCP, although this latter is not considered mandatory by the Brazilian legislation. Unfortunately, the lack of skilled labor, along with failures in complying established protocols have impaired quality of fruit pulps. It has been necessary to collect all information available with the aim to identify the most important hazards within fruit pulp processing lines. Standardizing methods and practices within the Brazilian fruit pulp industry would assurance high quality status to tropical fruit pulps and the commercial growth of this vegetal product towards international markets.

  6. EFFECTS OF ALKALINE PRE-IMPREGNATION AND PULPING ON MALAYSIA CULTIVATED KENAF (HIBISCUS CANNABINUS

    Directory of Open Access Journals (Sweden)

    Lin Suan Ang

    2010-05-01

    Full Text Available This study was carried out to identify an appropriate alkaline pulping condition for Malaysia cultivated kenaf (Hibiscus cannabinus L.. The chemical composition of the kenaf bast and core fibers, and also whole stalk with different growing time were examined prior to pulping attempts. The results of various soda-AQ pulping showed that the degree of carbohydrate degradation and delignification increased with the increase of active alkali and cooking temperature, but decreased with the increase of liquor to material (L:M ratio. The most satisfactory properties of pulp and handsheets from bast could be attained by employing soda-AQ pulping with 19.4% active alkali, 0.10% AQ, and L:M ratio of 7:1 cooked for 2 hours at 160˚C. Besides, it was also found that a mild alkaline pre-impregnation prior pulping improved the pulp viscosity and handsheets’ strength properties, especially the tensile index and folding endurance effectively. Moreover, among the three alkaline pulping processes—kraft, kraft-AQ, and soda-AQ—the results of pulp and handsheet properties showed that the soda-AQ pulp was comparable or even slightly of higher quality than the kraft pulps. Between the unbeaten bast and core soda-AQ handsheets, the strength properties of the core were higher than the bast, as the thin-walled core fibers exhibited much better conformability than the thick-walled bast fibers.

  7. Properties of Enzyme Pretreated Wikstroemia sikokiana and Broussonetia papyrifera Bast Fiber Pulps

    Directory of Open Access Journals (Sweden)

    Lang-Dong Lin

    2015-04-01

    Full Text Available Xylanase, pectinase complex, and BL11 pectinase were employed for the pretreatment of gampi and paper mulberry bast fiber pulps prior to chlorine dioxide bleaching. The bleaching efficiencies of the pulps with different enzymatic pretreatments were investigated. Accelerated aging by heat-humidity treatment was also conducted to evaluate yellowing phenomena and to estimate the prevention of brightness reversion (brightness retention by enzymatic pretreatment. The order of active chlorine required with respect to pretreatment was pectinase complex > xylanase > BL11 pectinase for soda and soda/oxalate gampi pulps and pectinase complex > BL11 pectinase > xylanase for soda and soda/oxalate paper mulberry pulps. Higher brightness retention values were observed for soda/oxalate pulps compared to soda pulps. The brightness retention levels for gampi pulps and mulberry pulps after ClO2 bleaching with enzymatic pretreatment were higher than the levels of ClO2 and NaClO bleaching pulps. Enzymatic treatments were thus able to reduce the usage of ClO2 and to assist in producing photo-stable paper materials for art and artifact-repairing applications. Thus, enzymatic pretreatment of the pulp has the potential to meet world trends and environmental sustainability for pulp and paper industries.

  8. Microwave-assisted deposition of silver nanoparticles on bamboo pulp fabric through dopamine functionalization

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Linghui [College of Light Industry, Textile and Food Engineering, Sichuan University, No.24 South Section 1, Yihuan Road, Chengdu (China); Guo, Ronghui, E-mail: ronghuiguo214@126.com [College of Light Industry, Textile and Food Engineering, Sichuan University, No.24 South Section 1, Yihuan Road, Chengdu (China); Lan, Jianwu [College of Light Industry, Textile and Food Engineering, Sichuan University, No.24 South Section 1, Yihuan Road, Chengdu (China); Jiang, Shouxiang [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China); Lin, Shaojian [Institute for Technical and Macromolecular Chemistry, University of Hamburg Bundesstrasse 45, D-20146 Hamburg (Germany)

    2016-11-15

    Highlights: • Silver nanoparticles were synthesized on bamboo pulp fabric using dopamine as an adhesive and reducing agent under microwave radiation. • Silver coated bamboo pulp fabric modified with dopamine has good UV protection and hydrophobic property. • Silver nanoparticles can be strongly fixed on dopamine modified bamboo pulp fabric. - Abstract: Silver nanoparticles were synthesized on bamboo pulp fabric with dopamine as the adhesive and reducing agent under microwave radiation. The silver nanoparticle coated bamboo pulp fabrics were characterized by X-ray photoelectron spectroscopy, scanning electron microscope and X-ray diffraction. Ultraviolet (UV) protection, color and water contact angles of the silver nanoparticle coated bamboo pulp fabrics were evaluated. In addition, the influences of concentrations of dopamine and treatment time on color strength (K/S values) of the silver nanoparticle coated fabric were investigated. Fastness to washing was employed to evaluate the adhesive strength between the silver coating and the bamboo pulp fabric modified with dopamine. The results show that the dopamine modified bamboo pulp fabric is evenly covered with silver nanoparticles. The silver nanoparticle coated bamboo pulp fabric modified with dopamine shows the excellent UV protection with an ultraviolet protection factor of 157.75 and the hydrophobicity with a water contact angle of 132.4°. In addition, the adhesive strength between the silver nanoparticles and bamboo pulp fabric is significantly improved. Silver nanoparticles coating on bamboo pulp fabric modified with dopamine is environmentally friendly, easy to carry out and highly efficient.

  9. Original Article. Toxic effect of sodium fluoride on hydroxyproline level and expression of collagen-1 gene in rat bone and its amelioration by Tamrindus indica L. fruit pulp extract

    Directory of Open Access Journals (Sweden)

    Gupta Amit Raj

    2016-03-01

    Full Text Available Excessive fluoride intoxication plays an important role in the development of dental, skeletal and non-skeletal fluorosis. The aim of this study was to ascertain the toxic effect of excessive fluoride ingestion on the level of hydroxyproline and expression of type 1 collagen gene in rat bone and its amelioration by supplementation with Tamarindus indica fruit pulp extract. Forty albino rats were randomly assigned to four groups. The first group served as control and received only tap water. The second group received sodium fluoride (200 ppm through drinking water. The third group received T. indica fruit pulp extract (200 mg/kg body weight alone and the fourth group received the T. indica fruit pulp extract (200 mg/kg body weight along with fluorinated drinking water (200 ppm daily by gavage for a period of 90 days. The level of hydroxyproline and expression of type 1 collagen gene using quantitative real time PCR in the tibia bone decreased significantly with continuous exposure to sodium fluoride. Co-administration of T. indica fruit pulp extract during exposure to fluoride through drinking water restored the level of calcium, phosphorus and alkaline phosphatase in serum and the concentration of hydroxyproline in urine. It increased the level of hydroxyproline and expression of type 1 collagen gene in the tibia as compared to untreated fluoride-exposed rats. It is concluded that T. indica fruit pulp extract has an ameliorative potential to protect the bone from fluoride induced collagen damage.

  10. Relationship between lignin structure and delignification degree in Pinus pinaster kraft pulps.

    Science.gov (United States)

    Baptista, C; Robert, D; Duarte, A P

    2008-05-01

    This study examines the structure of residual and dissolved lignins from Pinus pinaster pulps obtained at different degrees of delignification by laboratory conventional kraft pulping. The cooking H factor was varied from 85 to 8049. The residual and dissolved lignin samples were characterised by elemental analysis, residual carbohydrate content, permanganate oxidation and 13C NMR spectroscopy. The reflectance factor of the pulps was also determined in order to tentatively correlate the delignification degree and residual lignin structure with the pulp colour. The obtained results confirmed that the delignification degree increases the condensation of the lignin structure, which might have an influence upon the observed increased pulp colour. The lack of selectivity of kraft pulping process in the case of more delignified pulps was also shown.

  11. Isolation and characterization of pulp from sugarcane bagasse and rice straw

    International Nuclear Information System (INIS)

    Saiful Azhari, S.; Suhardy, D.; Kasim, F.H; Nazry Saleh, M.

    2007-01-01

    The amount of sugarcane bagasse and rice straw in the state of Perlis (Malaysia) is abundant while its utilization is still limited. One of the alternatives for the bagasse and straw utilization is as pulp raw material. This paper reviews on pulp from sugarcane bagasse and rice straw and its suitability for paper production. In this study, the pulp was extracted by the Soxhlet extraction method. The objective of this study was to investigate the cellulose, lignin and silica content of the pulp from sugarcane bagasse and rice straw. For rice straw, the presence of large amount of pentosanes in the pulp and black liquors, which also contain silica were decreased the using of straw in the paper industry. Therefore, formic acid pulping and NaOH treatment are studied to reduce or prevent silica. The isolated pulp samples were further characterized by Scanning Electron Microscope (SEM) to investigate their fiber dimensions. (Author)

  12. Positive and negative aspects of soda/anthraquinone pulping of hardwoods.

    Science.gov (United States)

    Francis, R C; Bolton, T S; Abdoulmoumine, N; Lavrykova, N; Bose, S K

    2008-11-01

    The positive aspects of the non-sulfur soda/anthraquinone (SAQ) process are mostly tied to improved energy efficiency while lower pulp brightness after bleaching is its most significant drawback. A credible method that quantifies bleachability as well as an approach that solves the problem for SAQ pulps from hardwoods will be described. A straight line correlation (R2=0.904) was obtained between O2 kappa number and final light absorption coefficient (LAC) value after standardized OD0EpD1 bleaching of nine hardwood kraft pulps from three laboratories and one pulp mill. The bleachability of pulps from four different soda processes catalyzed by anthraquinone (AQ) and 2-methylanthraquinone (MAQ) was compared to that of conventional kraft pulps by comparing O2 kappa number decrease and final LAC values. It was observed that a mild hot water pre-hydrolysis improved the bleachability of SAQ pulps to a level equal to that of kraft.

  13. Platelet-rich Preparation may serve as a Powerful Tool for Therapeutic Dental Pulp Regeneration

    Directory of Open Access Journals (Sweden)

    Hai-Hua Sun

    2011-09-01

    Full Text Available Introduction: Regeneration of dental pulp tissues presents one of the most challenging issues in regenerative dentistry due to their extremely poor intrinsic ability for self-healing and re-growth.The hypothesis: We hypothes-ize that patient-derived platelet-rich preparation can be used in clinical endodontic regenerative procedure, serving as a powerful tool for therapeutic dental pulp regeneration.Evaluation of the hypothesis: The cell transplantation does not always obtain the good result because of the low survival rate of transplanted cells. In addition, the use of ex vivo manipulated cell products faces many translational hurdles in treating non-vital disease. Recently, the body cells are focused as a potential source for therapeutics. Some researchers have demonstrated that endogenous stem cells may be recruited to a desired anatomic site pharma-cologically. This is spurring interest in developing new generation of biomaterials that incorporate and release selected powerful extracellular influences in a near-physiological fashion, and subsequently capture endogenous stem cells and influence their fates for regene-ration. The use of patient-derived products such as platelet-rich preparations that contain a multitude of endogenous growth factors and proteins is a clinically translatable biotechnology for this proposes. These simple and cost efficient procedures may have a potential impact in reducing the economic costs for standard medical treatments in regenerative endodontics.

  14. Biological fermentative hydrogen production from olive pulp at 35 degrees C

    Energy Technology Data Exchange (ETDEWEB)

    Koutrouli, E.C.; Gavala, H.N.; Skiadas, I.V.; Lyberatos, G. [Patras Univ., Patras (Greece). Dept. of Chemical Engineering

    2004-07-01

    In response to energy security and environmental concerns, there is renewed interest in the use of hydrogen gas as a renewable energy source. However, many processes for generating hydrogen are extremely energy intensive and costly. This study focused on biological production of hydrogen from wastewater or other biomass. Photosynthetic and fermentation processes were outlined, but the main focus of this paper was on continuous anaerobic fermentation of low cost substrates such as olive pulp at 35 degrees C. This process is linked to the acidogenic stage of anaerobic digestion where carbohydrates are the preferred carbon source. Volatile fatty acids and alcohols are produced simultaneously with the hydrogen gas. An added advantage is that the effluent from the fermentation process can be further used by methanogenesis due to its rich organic acids content. Batch experiments with olive pulp resulted in 2.5 mmole of hydrogen per gram of total carbohydrates. It was noted that more research is required to maximize hydrogen production in a continuous process. It was suggested that hydrogen production could be optimized through hydrolysis of the non-soluble carbohydrates. This could be accomplished through physicochemical or biological pretreatments. 7 refs., 3 tabs., 1 fig.

  15. Ionizing radiation induces senescence and differentiation of human dental pulp stem cells.

    Science.gov (United States)

    Havelek, R; Soukup, T; Ćmielová, J; Seifrtová, M; Suchánek, J; Vávrová, J; Mokrý, J; Muthná, D; Řezáčová, M

    2013-01-01

    Head and neck cancer is one of the most common cancers in Europe. Many current anti-cancer treatments, including ionizing radiation, induce apoptosis via DNA damage. Unfortunately, such treatments are non-selective to cancer cells and produce similar toxicity in normal cells, including adult stem cells. One of the fundamental properties of an adult stem cell is that it does not have any tissue-specific structures that allow it to perform specialized functions. However, under certain stimuli, unspecialized adult stem cells can give rise to specialized cells to generate replacements for cells that are lost during one's life or due to injury or disease. Nevertheless, specialization of stem cells must be controlled by specific milieu and also initiated at the proper time, making the entire process beneficial for tissue recovery and maintaining it for a long time. In this paper we assess whether irradiated dental pulp stem cells have maintained open their options to mature into specialized cells, or whether they have lost their unspecialized (immature) state following irradiation. Our findings showed radiation-induced premature differentiation of dental pulp stem cells towards odonto-/osteoblast lineages in vitro. Matrix calcification was visualized from Day 6 or Day 9 following irradiation of cells expressing low or high levels of CD146, respectively.

  16. Odontoblasts: Specialized hard-tissue-forming cells in the dentin-pulp complex.

    Science.gov (United States)

    Kawashima, Nobuyuki; Okiji, Takashi

    2016-07-01

    Odontoblasts are specialized cells that produce dentin and exhibit unique morphological characteristics; i.e., they extend cytoplasmic processes into dentinal tubules. While osteoblasts, which are typical hard-tissue-forming cells, are generated from mesenchymal stem cells during normal and pathological bone metabolism, the induction of odontoblasts only occurs once during tooth development, and odontoblasts survive throughout the lives of healthy teeth. During the differentiation of odontoblasts, signaling molecules from the inner enamel epithelium are considered necessary for the differentiation of odontoblast precursors, i.e., peripheral dental papilla cells. If odontoblasts are destroyed by severe external stimuli, such as deep caries, the differentiation of dental pulp stem cells into odontoblast-like cells is induced. Various bioactive molecules, such as non-collagenous proteins, might be involved in this process, although the precise mechanisms responsible for odontoblast differentiation have not been fully elucidated. Recently, our knowledge about the other functional activities of odontoblasts (apart from dentin formation) has increased. For example, it has been suggested that odontoblasts might act as nociceptive receptors, and surveillance cells that detect the invasion of exogenous pathogens. The regeneration of the dentin-pulp complex has recently gained much attention as a promising future treatment modality that could increase the longevity of pulpless teeth. Finally, congenital dentin anomalies, which are concerned with the disturbance of odontoblast functions, are summarized. © 2016 Japanese Teratology Society.

  17. TET1 knockdown inhibits the odontogenic differentiation potential of human dental pulp cells.

    Science.gov (United States)

    Rao, Li-Jia; Yi, Bai-Cheng; Li, Qi-Meng; Xu, Qiong

    2016-06-30

    Human dental pulp cells (hDPCs) possess the capacity to differentiate into odontoblast-like cells and generate reparative dentin in response to exogenous stimuli or injury. Ten-eleven translocation 1 (TET1) is a novel DNA methyldioxygenase that plays an important role in the promotion of DNA demethylation and transcriptional regulation in several cell lines. However, the role of TET1 in the biological functions of hDPCs is unknown. To investigate the effect of TET1 on the proliferation and odontogenic differentiation potential of hDPCs, a recombinant shRNA lentiviral vector was used to knock down TET1 expression in hDPCs. Following TET1 knockdown, TET1 was significantly downregulated at both the mRNA and protein levels. Proliferation of the hDPCs was suppressed in the TET1 knockdown groups. Alkaline phosphatase activity, the formation of mineralized nodules, and the expression levels of DSPP and DMP1 were all reduced in the TET1-knockdown hDPCs undergoing odontogenic differentiation. Based on these results, we concluded that TET1 knockdown can prevent the proliferation and odontogenic differentiation of hDPCs, which suggests that TET1 may play an important role in dental pulp repair and regeneration.

  18. Optical and Physical Properties of ONP Deinked Pulp

    Directory of Open Access Journals (Sweden)

    Iman Akbarpoor

    2012-01-01

    Full Text Available Enzymes are protein molecules with complex structures that accelerate the biochemical reactions. Activity of these chemical compounds is accomplished at limited range of pH, temperature and concentration. In this study, the effects of different concentrations of cellulose enzyme were investigated on deinking of old newsprint. Old newsprint (ONP was repulped at 5% consistency for 10 minutes in disintegrator with total revolution number of 26500. Enzymatic treatments of recycled ONP pulp were done under constant conditions (10% consistency,treatment time of 15 minutes, pH range of 5-5.5 at different cellulose concentrations of 0.025, 0.05, 0.1 and 0.2% (based on oven-dry waste paper. The optical and physical properties of the standard paper (60g/m2 made at different concentrations of cellulose were evaluated in comparison with control pulp (untreated ONP pulp with cellulase. Overall, the results achieved by comparison the optical properties of the paper produced indicated that using cellulase in deinking of ONP led to increase the brightness and the yellowness and decrease the opacity. The brightness was improved to a maximum level of 47.5 ISO %, but the yellowness was decreased to a minimum level of 11.3 ISO %, while the brightness reduced and the yellowness increased at higher concentrations than 0.05% cellulase. The highest opacity of 99.3 ISO % was achieved using 0.1% cellulase even higher than control pulp. The results gained by comparison the physical properties of the paper showed that using cellulase resulted in decrease of paper calliper, air resistance and density and improve the freeness of pulp

  19. EVALUATION OF CONDITION OF THE PULP BY PULSE OXIMETRY.

    Directory of Open Access Journals (Sweden)

    Dimitar Kosturkov

    2015-12-01

    Full Text Available Purpose: To conduct pulse oximetry (PO and electric pulp test (EPT on intact frontal teeth in clinically healthy patients aged between 18 and 25 years who do not have periodontal disease. Material/Methods: To achieve the aim 1058 teeth of 31 patients were studied. The following inclusion criteria for the study were set: 1. Age – 18-25 years. 2. Clinically healthy patient, who does not have any systemic diseases, do not take any medicine systematically. 3. Intact frontal teeth – without carious lesions, restorations or root canal treatment. 4. Lack of periodontal disease. Research was conducted with a pulse oximeter Contec™ - CMS60D and a custom made probe holder. Results: Average values obtained by pulse oximetry in upper jaw vary between 83% and 85%. In lower jaw – between 82% and 85%. 99% is the maximum and 48% is the minimum registered value. The average value of the measurement of all the teeth is 84%. The average saturation measured on the small finger of the right hand of the patient is 98%. The average value of EPT for all teeth is 4 μA. The maximum measured value is 20 μA, and the minimum - 1 μA. Conclusions: 1. Adequate study of the pulp includes two complementary methods – electric pulp test (evaluation of innervation and pulse oximetry (assessment of pulp microcirculation. 2. Teeth that are larger in size have larger values of PO and EPT, which is in direct relation to the size of their pulp chamber. 3. The total saturation, measured in the little finger of the right hand is greater than the one of the teeth.

  20. Review on Bamboo Utilization as Biocomposites, Pulp and Bioenergy

    Science.gov (United States)

    Yusuf, Sulaeman; Syamani, F. A.; Fatriasari, W.; Subyakto

    2018-03-01

    One of potential non wood bioresources utilized in industrial application is bamboos. Bamboos are include in graminae family which have high biomass productivity, easy and rapid production, wide avability and high holocellulose content. Indonesia has a huge potential of bamboos, more than 162 bamboo species are found however only some of them are planted that have a high economic value. Bamboos have some advantages such as can be harvested at 3 years, straight culm, high strength, easy to be processed, and relatively cheap. Research Center for Biomaterials has developed utilization of bamboo culm for ply bamboo product as alternative of plywood since 1995, using gombong bamboo, tali bamboo, sembilang bamboo, andong bamboo with PF resin as adhesive. Other biocomposite products from bamboos include particle board, cement board and polymer-bamboo fiber composites. In term of processing technique and final product quality, bamboo composites from ply bamboo are the most prospectable material to be utilized in industrial application. Yellow bamboo and betung bamboo have also been developed as pulp and paper. Biopulping using soda and kraft pulping after biological pretreatment using white rot fungi to remove lignin was used as pulping method in this conversion. Biokraft pulping with Trametes versicolor for 45 days with inoculum loading of 10% resulted better pulp quality compared to the other fungi. Betung bamboo had good morphological characteristics and chemical component content to be converted into bioenergy such as bioethanol. Several pretreatment methods have been developed in order to result high sugar yield. Microwave assisted acid hydrolysis was preferedin producing higher yield from the pretreated bamboo compared to enzymatic hydrolysis. By using this method, the bamboo pretreated by biological-microwave pretreatment results higher improvement to increase sugar yield.

  1. Isolation of Mesenchymal Stem Cells from Human Deciduous Teeth Pulp

    Directory of Open Access Journals (Sweden)

    Aileen I. Tsai

    2017-01-01

    Full Text Available This study aimed to identify predictors of success rate of mesenchymal stem cell (MSC isolation from human deciduous teeth pulp. A total of 161 deciduous teeth were extracted at the dental clinic of Chang Gung Memorial Hospital. The MSCs were isolated from dental pulps using a standard protocol. In total, 128 colonies of MSCs were obtained and the success rate was 79.5%. Compared to teeth not yielding MSCs successfully, those successfully yielding MSCs were found to have less severe dental caries (no/mild-to-moderate/severe: 63.3/24.2/12.5% versus 12.5/42.4/42.4%, P<0.001 and less frequent pulpitis (no/yes: 95.3/4.7% versus 51.5/48.5%, P<0.001. In a multivariate regression model, it was confirmed that the absence of dental caries (OR = 4.741, 95% CI = 1.564–14.371, P=0.006 and pulpitis (OR = 9.111, 95% CI = 2.921–28.420, P<0.001 was significant determinants of the successful procurement of MSCs. MSCs derived from pulps with pulpitis expressed longer colony doubling time than pulps without pulpitis. Furthermore, there were higher expressions of proinflammatory cytokines, interleukin- (IL- 6 and monocyte chemoattractant protein- (MCP- 1, P<0.01, and innate immune response [toll-like receptor 1 (TLR1 and TLR8, P<0.05; TLR2, TLR3, and TLR6, P<0.01] in the inflamed than noninflamed pulps. Therefore, a carious deciduous tooth or tooth with pulpitis was relatively unsuitable for MSC processing and isolation.

  2. Semaphorin 3A Induces Odontoblastic Phenotype in Dental Pulp Stem Cells.

    Science.gov (United States)

    Yoshida, S; Wada, N; Hasegawa, D; Miyaji, H; Mitarai, H; Tomokiyo, A; Hamano, S; Maeda, H

    2016-10-01

    In cases of pulp exposure due to deep dental caries or severe traumatic injuries, existing pulp-capping materials have a limited ability to reconstruct dentin-pulp complexes and can result in pulpectomy because of their low potentials to accelerate dental pulp cell activities, such as migration, proliferation, and differentiation. Therefore, the development of more effective therapeutic agents has been anticipated for direct pulp capping. Dental pulp tissues are enriched with dental pulp stem cells (DPSCs). Here, the authors investigated the effects of semaphorin 3A (Sema3A) on various functions of human DPSCs in vitro and reparative dentin formation in vivo in a rat dental pulp exposure model. Immunofluorescence staining revealed expression of Sema3A and its receptor Nrp1 (neuropilin 1) in rat dental pulp tissue and human DPSC clones. Sema3A induced cell migration, chemotaxis, proliferation, and odontoblastic differentiation of DPSC clones. In addition, Sema3A treatment of DPSC clones increased β-catenin nuclear accumulation, upregulated expression of the FARP2 gene (FERM, RhoGEF, and pleckstrin domain protein 2), and activated Rac1 in DPSC clones. Furthermore, in the rat dental pulp exposure model, Sema3A promoted reparative dentin formation with dentin tubules and a well-aligned odontoblast-like cell layer at the dental pulp exposure site and with novel reparative dentin almost completely covering pulp tissue at 4 wk after direct pulp capping. These findings suggest that Sema3A could play an important role in dentin regeneration via canonical Wnt/β-catenin signaling. Sema3A might be an alternative agent for direct pulp capping, which requires further study. © International & American Associations for Dental Research 2016.

  3. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.E.J.; Soetens, F.

    2005-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical

  4. Application of Induced Pluripotent Stem Cells Reprogrammed from Dental Pulp Cells: a Novel Approach for Tooth Regeneration

    Directory of Open Access Journals (Sweden)

    Xiaoyan Zhou

    2011-03-01

    Full Text Available Introduction: Candidate human dental stem/progenitor cells have been isolated and charac-terized from dental tissues and shown to hold the capability to differentiate into tooth-generating cells. However, ad-vances in engineering a whole tooth by these stem cells are hindered by various factors, such as the poor availability of human primitive tooth bud stem cells, difficulties in isolating and purifying dental mesenchymal stem cells and ethical controversies when using embryonic oral epithelium. As a result it is meaningful to find other autologous dental cells for the purpose of reconstructing a tooth.The hypothesis: Previous studies demonstrated that somatic cells can be reprogrammed into induced pluripotent stem cells by ex-ogenous expression Oct-4 and Sox-2. On the basis of these findings we can reasonably hypothesize that when transfected with specific transcription factors Oct-4 and Sox-2, dental pulp cells, the main cell in pulp, could also be reprogrammed into induced pluripotent stem cells, which are considered to be of best potential to regenerate a whole tooth. Evaluation of the hypothesis: After transfection with Oct-4 and Sox-2 into human dental pulp cells, the positive colonies are isolated and then identified according to the characteristics of iPS cells. These cells are further investigated the capability in differentiating into ameloblasts and odontoblasts and finally seeded onto the sur-face of a tooth-shaped biodegradable polymer scaffold to detect the ability of constructing a bioengineered tooth.

  5. Predicting Bacillus coagulans spores inactivation in tomato pulp under nonisothermal heat treatments.

    Science.gov (United States)

    Zimmermann, Morgana; Longhi, Daniel A; Schaffner, Donald W; Aragão, Gláucia M F

    2014-05-01

    The knowledge and understanding of Bacillus coagulans inactivation during a thermal treatment in tomato pulp, as well as the influence of temperature variation during thermal processes are essential for design, calculation, and optimization of the process. The aims of this work were to predict B. coagulans spores inactivation in tomato pulp under varying time-temperature profiles with Gompertz-inspired inactivation model and to validate the model's predictions by comparing the predicted values with experimental data. B. coagulans spores in pH 4.3 tomato pulp at 4 °Brix were sealed in capillary glass tubes and heated in thermostatically controlled circulating oil baths. Seven different nonisothermal profiles in the range from 95 to 105 °C were studied. Predicted inactivation kinetics showed similar behavior to experimentally observed inactivation curves when the samples were exposed to temperatures in the upper range of this study (99 to 105 °C). Profiles that resulted in less accurate predictions were those where the range of temperatures analyzed were comparatively lower (inactivation profiles starting at 95 °C). The link between fail prediction and both lower starting temperature and magnitude of the temperature shift suggests some chemical or biological mechanism at work. Statistical analysis showed that overall model predictions were acceptable, with bias factors from 0.781 to 1.012, and accuracy factors from 1.049 to 1.351, and confirm that the models used were adequate to estimate B. coagulans spores inactivation under fluctuating temperature conditions in the range from 95 to 105 °C. How can we estimate Bacillus coagulans inactivation during sudden temperature shifts in heat processing? This article provides a validated model that can be used to predict B. coagulans under changing temperature conditions. B. coagulans is a spore-forming bacillus that spoils acidified food products. The mathematical model developed here can be used to predict the spoilage

  6. Indirect pulp capping in primary molar using glass ionomer cements

    Directory of Open Access Journals (Sweden)

    Murtia Metalita

    2014-12-01

    Full Text Available Background: Indirect pulp capping in primary teeth, however, is more rarely conducted than permanent teeth, since it thought to have low impact and most suggestion is for taking caries lesion aggressively on primary teeth. Purpose: The study was aimed to evaluate the subjective complaint, clinical symptom, and radiographic appearance of indirect pulp capping treatment using glass ionomers cements in primary molar. Methods: Sixteen children in range of age 6 to 8 years old, who visited Clinic of Pediatric Dentistry Universitas Airlangga Dental Hospital, Surabaya Indonesia, were the subject of study. They had one occlusal dental caries on one side of maxillary or mandibular primary molar with the diagnose of pulpitis reversible. The experimental group, had indirect pulp capping treatment with glass ionomer cements (GC Fuji VII®, while the control group, had indirect pulp capping treatment with calcium hydroxide (Metapaste. Each group was filled with GC Fuji IX® as permanent restoration. After one week, one month, and three months later, the observations were made on subjective complaint, clinical symptom, and radiographic appearance. Results: The results showed no subjective complaint such as pain or problem on mastication; no negative clinical symptoms such as pain on palpation, gingivitis or periodontitis, and abnormal tooth mobility; no negative radiographic appearance such as pathological apical radioluscency, internal or external resorbtion, and change of ligament periodontal widthafter the treatment. Conclusion: The study suggested that indirect pulp capping treatment using glass ionomer cement materials on primary teeth might be considered to be the treatment choice.Latar belakang: Indirect pulp capping pada gigi sulung lebih jarang dilakukan dibandingkan gigi permanen, karena dianggap memiliki dampak yang rendah dan sebagian besar menyarankan untuk mengambil lesi karies secara agresif pada gigi sulung. Tujuan: Penelitian ini bertujuan

  7. IGCC power plant integrated to a Finnish pulp and paper mill. IEA Bioenergy. Techno-economic analysis activity

    Energy Technology Data Exchange (ETDEWEB)

    Koljonen, T.; Solantausta, Y. [VTT Energy, Espoo (Finland). New Energy Technologies; Salo, K.; Horvath, A. [Carbona Inc. (Finland)

    1999-11-01

    In Finland, the pulp and paper industry is the largest consumer of energy among the industries and its power demand will increase due to economical and strict environ- mental requirements. The ageing of oil and biomass boilers in Finland also represents a window of opportunity for the introduction of new environmentally sound technology with a high efficiency in power production, e.g., in biomass gasification. This site-specific study describes the technical and economic feasibility of a biomass gasification combined cycle producing heat and power for a typical Finnish pulp and paper mill. The mill produces SC (super calantered) paper 500 000 ADt/a. The paper mill employs sulphate pulp and GW (ground wood) pulp. The capacity of the pulp mill is 400 000 ADt/a (air dry ton/year) of which 120 000 ADt/a is used at the site. The heat demand of the integrate is covered by a recovery boiler and a bark boiler. A condensing steam turbine with two extractions generates electricity for the mill. The aim is to replace an old bark boiler by an IGCC (Integrated Gasification Combined Cycle) to enhance the economy and environmental performance of the power plant. The IGCC feasibility study is conducted for an pulp and paper integrate because of its suitable infrastructure for IGCC and a large amount of wood waste available at the site. For comparison, the feasibility of an IGCC integrated to a pulp mill is also assessed. The IGCC concept described is based on research and development work performed by Carbona, Inc., who acquired the rights for know-how of Enviropower, Inc. The operation and design of the IGCC concept is based on a 20 MWe gas turbine (MW151). The heat of gas turbine exhaust gas is utilised in a HRSG (Heat Recovery Steam Generator) of two pressure levels to generate steam for the pulp and paper mill and the steam turbine. The MCC power plant operates in condensing mode. The total investment cost of the IGCC plant is estimated at FIM 417 million (USD 83.4 million

  8. IGCC power plant integrated to a Finnish pulp and paper mill. IEA Bioenergy. Techno-economic analysis activity

    International Nuclear Information System (INIS)

    Koljonen, T.; Solantausta, Y.

    1999-01-01

    In Finland, the pulp and paper industry is the largest consumer of energy among the industries and its power demand will increase due to economical and strict environ- mental requirements. The ageing of oil and biomass boilers in Finland also represents a window of opportunity for the introduction of new environmentally sound technology with a high efficiency in power production, e.g., in biomass gasification. This site-specific study describes the technical and economic feasibility of a biomass gasification combined cycle producing heat and power for a typical Finnish pulp and paper mill. The mill produces SC (super calantered) paper 500 000 ADt/a. The paper mill employs sulphate pulp and GW (ground wood) pulp. The capacity of the pulp mill is 400 000 ADt/a (air dry ton/year) of which 120 000 ADt/a is used at the site. The heat demand of the integrate is covered by a recovery boiler and a bark boiler. A condensing steam turbine with two extractions generates electricity for the mill. The aim is to replace an old bark boiler by an IGCC (Integrated Gasification Combined Cycle) to enhance the economy and environmental performance of the power plant. The IGCC feasibility study is conducted for an pulp and paper integrate because of its suitable infrastructure for IGCC and a large amount of wood waste available at the site. For comparison, the feasibility of an IGCC integrated to a pulp mill is also assessed. The IGCC concept described is based on research and development work performed by Carbona, Inc., who acquired the rights for know-how of Enviropower, Inc. The operation and design of the IGCC concept is based on a 20 MWe gas turbine (MW151). The heat of gas turbine exhaust gas is utilised in a HRSG (Heat Recovery Steam Generator) of two pressure levels to generate steam for the pulp and paper mill and the steam turbine. The MCC power plant operates in condensing mode. The total investment cost of the IGCC plant is estimated at FIM 417 million (USD 83.4 million

  9. Citrus pulp pellets as an additive for orange bagasse silage

    Directory of Open Access Journals (Sweden)

    R. K. Grizotto

    2017-03-01

    Full Text Available This study evaluated the fermentation profile of orange bagasse ensiled with three levels of dry matter (DM using citrus pulp pellets as a moisture-absorbing additive. Thirty experimental silos (3 treatments, 5 storage times, 2 replicates were prepared using 25-liter plastic buckets containing orange bagasse and three levels of pelleted citrus pulp (0, 6% and 20% as additive. A completely randomized design with repeated measures over time was used. The periods of anaerobic storage were 3, 7, 14, 28 and 56 days. Natural orange bagasse contained 13.9% DM, which increased to 19.1% and 25.5% with the inclusion of 6% and 20% citrus pulp pellets, respectively. The apparent density was inversely correlated with DM content and a higher level of compaction (982 kg/m3 was observed in the mass ensiled with the lowest DM level (13.9%. Additionally, lower compaction (910 kg/m3 was found in the mass ensiled with the additive. The chemical composition of the mass ensiled with or without citrus pulp pellets did not differ significantly in terms of protein, ether extract, neutral detergent fiber, lignin or in vitro DM digestibility (P≥0.05, as expected. Thus, it was possible to analyze only the effect of the inclusion of citrus pulp pellets on the increase in DM content. The inclusion of 20% of the additive reduced (P<0.01 losses due to effluent (98% less and gas production (81% less compared to the control treatment at the end of the anaerobic storage period. In this treatment, a higher (P≤0.05 log number of lactic acid bacteria (4.61 log CFU/g was also observed compared to the other treatments, indicating that the increase in DM favored the growth of these bacteria. In addition, the low yeast count (about 1 log CFU/g sample and the pH below 4.0, which were probably due to the production of lactic and acetic acids, show that the orange bagasse is rich in fermentable soluble carbohydrates and is indicated for ensiling. In conclusion, orange bagasse can be

  10. Enzymatic Extraction of Hydroxycinnamic Acids from Coffee Pulp

    Directory of Open Access Journals (Sweden)

    Ernesto Favela-Torres

    2011-01-01

    Full Text Available Ferulic, caffeic, p-coumaric and chlorogenic acids are classified as hydroxycinnamic acids, presenting anticarcinogenic, anti-inflammatory and antioxidant properties. In this work, enzymatic extraction has been studied in order to extract high value-added products like hydroxycinnamic acids from coffee pulp. A commercial pectinase and enzyme extract produced by Rhizomucor pusillus strain 23aIV in solid-state fermentation using olive oil or coffee pulp (CP as an inducer of the feruloyl esterase activity were evaluated separately and mixed. The total content (covalently linked and free of ferulic, caffeic, p-coumaric and chlorogenic acids was 5276 mg per kg of coffee pulp. Distribution was as follows (in %: chlorogenic acid 58.7, caffeic acid 37.6, ferulic acid 2.1 and p-coumaric acid 1.5. Most of the hydroxycinnamic acids were covalently bound to the cell wall (in %: p-coumaric acid 97.2, caffeic acid 94.4, chlorogenic acid 76.9 and ferulic acid 73.4. The content of covalently linked hydroxycinnamic acid was used to calculate the enzyme extraction yield. The maximum carbon dioxide rate for the solid-state fermentation using olive oil as an inducer was higher and it was reached in a short cultivation time. Nevertheless, the feruloyl esterase (FAE activity (units per mg of protein obtained in the fermentation using CP as an inducer was 31.8 % higher in comparison with that obtained in the fermentation using olive oil as the inducer. To our knowledge, this is the first report indicating the composition of both esterified and free ferulic, caffeic, p-coumaric and chlorogenic acids in coffee pulp. The highest yield of extraction of hydroxycinnamic acids was obtained by mixing the produced enzyme extract using coffee pulp as an inducer and a commercial pectinase. Extraction yields were as follows (in %: chlorogenic acid 54.4, ferulic acid 19.8, p-coumaric acid 7.2 and caffeic acid 2.3. An important increase in the added value of coffee pulp was mainly

  11. Avoiding total reduced sulfur (TRS) emissions from sodium sulfite pulping recovery processes

    International Nuclear Information System (INIS)

    Norman, J.C.; Sell, N.J.; Ciriacks, J.C.

    1990-01-01

    This paper reports that one of the current trends in paper-making with cellulose pulping is the use of high-yield processes. With yields greater than 65%, these processes include mechanical pulps (groundwood and thermomechanical pulps or TMP), and semichemical types (chemi-TMP or CTMP). Groundwood and TMP make up about 10% of North American pulp production. Semichemical pulp makes up about 7% and is mostly used for corrugating medium. High-yield pulping for linerboard, particularly using the alkaline sulfite process, is also likely to be used in the future. High-yield pulping is based primarily on the sulfite process using mostly sodium-based chemicals. A disadvantage of this process is the unavailability of a recovery system for the inorganic pulping chemicals. Generally, mills have not accepted any particular recovery system for this process. For this and other reasons, sulfite processes constitute only 3-4% of the total North American pulp production. If high-yield processes continue to increase in popularity, a sodium sulfite chemical recovery system will be needed. A number of chemical recovery systems have been developed in the past 30 years for sodium-based sulfite pulping processes, with most of the mills successfully using this process located in Scandinavia

  12. Catalase activity in healthy and inflamed pulp tissues of permanent teeth in young people.

    Science.gov (United States)

    Topcu, Kmc; Kırıcı, D Ö; Evcil, M S

    2016-01-01

    To evaluate catalase (CAT, EC 1.11.1.6) activity in healthy and inflamed dental pulp of young patient's teeth and to investigate if an active defense system oxidizing agents is present as a response to bacterial invasion. Twenty young patients between 15 and 25 ages, who were diagnosed to be healthy, were the source of the pulp tissue. The situation of the dental pulps was evaluated using clinical and radiographic assessments. The patients were divided two groups from healthy, and inflamed pulp tissues were obtained; each participant provided one pulp tissue specimens. The specimens were collected during endodontic treatment or by longitudinally grooving and splitting the teeth (if extracted). Catalase activity was determined through spectrophotometric methods and an independent sample t-test assessed the significance of differences between the groups. There was statistically a difference between healthy pulp tissue and inflamed pulp tissue (P catalase activity of healthy group was significantly lower than inflamed pulp groups. The present study has shown that a significant increase in catalase activity is determined in inflamed dental pulps, which is due to pulpitis in comparison to healthy dental pulp.

  13. The impact of kappa number composition on eucalyptus kraft pulp bleachability

    Directory of Open Access Journals (Sweden)

    M. M. Costa

    2007-03-01

    Full Text Available Consumption of chemicals during ECF bleaching of kraft pulp correlates reasonably well with kappa number, which measures with KMnO4 the total amount of oxidizable material in the pulp. However, the method does not distinguish between the oxidizable material in residual lignin and other structures susceptible to oxidation, such as hexenuronic acids (HexAs, extractives and carbonyl groups in the pulp. In this study an attempt is made to separate the main contributors to the kappa number in oxygen - delignified eucalyptus Kraft pulps and evaluate how these fractions behave during ECF bleaching using chlorine dioxide as the sole oxidant (DEDD sequence. Residual lignin and HexAs proved to be the main fractions contributing to the kappa number and chlorine dioxide consumption in ECF bleaching. Pulp bleachability with chlorine dioxide increases with increasing HexAs content of the pulp but chlorine dioxide per se does not react with HexAs. Reduction of pulp with sodium borohydride under conditions for removing carbonyl groups has no impact on bleachability. No correlation was found between the pulp of the extractive content and pulp bleachability. The removal of HexAs prior to ECF bleaching significantly decreases the formation of chlorinated organics in the pulp (OX and filtrates (AOX as well as of oxalic acids in the filtrates.

  14. Isolation and characterization of lignocellulose nanofibers from different wheat straw pulps.

    Science.gov (United States)

    Sánchez, Rafael; Espinosa, Eduardo; Domínguez-Robles, Juan; Loaiza, Javier Mauricio; Rodríguez, Alejandro

    2016-11-01

    Wheat straw was cooked under different pulping processes: Soda (100°C, 7% NaOH, 150min), Kraft (170°C, 16% alkalinity, 25% sulfidity, 40min) and Organosolv (210°C, 60% ethanol, 60min). Once the pulps were obtained, lignocellulose nanofibers (LCNF) were isolated by mechanical process and TEMPO-mediated oxidation followed by a high pressure homogenization. After pulping process, the different pulps were characterized and its chemical composition was determined. The pulps characterization indicates that the Soda process is the process that, despite producing less delignification, retains much of the hemicelluloses in the pulp, being this content a key factor in the nanofibrillation process. Regarding the LCNF obtained by mechanical process, those nanofibers isolated from Organosolv wheat pulp (OWP) and Kraft wheat pulp (KWP) show low values for nanofibrillation yield, specific surface area and greater diameter. However, those nanofibers isolated from Soda wheat pulp (SWP) reach much higher values for these parameters and presents a diameter of 14nm, smaller than those obtained by TEMPO-mediated oxidation from OWP. Smaller diameters are generally obtained in TEMPO-oxidized LCNF. This work concludes that the lignin content does not affect greatly to obtain LCNF as does the hemicellulose content, so it is accurate to use a soft pulping process. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Comparative Genome Analysis of Lactobacillus rhamnosus Clinical Isolates from Initial Stages of Dental Pulp Infection: Identification of a New Exopolysaccharide Cluster

    Science.gov (United States)

    Nadkarni, Mangala A.; Chen, Zhiliang; Wilkins, Marc R.; Hunter, Neil

    2014-01-01

    The human oral microbiome has a major role in oral diseases including dental caries. Our studies on progression of caries infection through dentin and more recently, the invasion of vital dental pulp, detected Lactobacillus rhamnosus in the initial stages of infection of vital pulp tissue. In this study employing current high-throughput next generation sequencing technology we sought to obtain insight into genomic traits of tissue invasive L. rhamnosus, to recognise biomarkers that could provide an understanding of pathogenic potential of lactobacilli, generally regarded as safe. Roche GS FLX+ technology was used to generate whole genome sequences of two clinical isolates of L. rhamnosus infecting vital pulp. Detailed genome-wide comparison of the genetic profiles of tissue invasive L. rhamnosus with probiotic L. rhamnosus was performed to test the hypothesis that specific strains of L. rhamnosus possessing a unique gene complement are selected for the capacity to invade vital pulp tissue. Analysis identified 264 and 258 genes respectively, from dental pulp-invasive L. rhamnosus strains LRHMDP2 and LRHMDP3 isolated from two different subjects that were not present in the reference probiotic L. rhamnosus strain ATCC 53103 (GG). Distinct genome signatures identified included the presence of a modified exopolysaccharide cluster, a characteristic confirmed in a further six clinical isolates. Additional features of LRHMDP2 and LRHMDP3 were altered transcriptional regulators from RpoN, NtrC, MutR, ArsR and zinc-binding Cro/CI families, as well as changes in the two-component sensor kinase response regulator and ABC transporters for ferric iron. Both clinical isolates of L. rhamnosus contained a single SpaFED cluster, as in L. rhamnosus Lc705, instead of the two Spa clusters (SpaCBA and SpaFED) identified in L. rhamnosus ATCC 53103 (GG). Genomic distance analysis and SNP divergence confirmed a close relationship of the clinical isolates but segregation from the reference

  16. PRODUCTION OF PRINTING AND WRITING PAPER GRADE PULP FROM ELEPHANT GRASS

    Directory of Open Access Journals (Sweden)

    Marcela Freitas Andrade

    2016-09-01

    Full Text Available The main goal of this study was to characterize chemically and morphologically elephant grass (Pennisetum purpureum, and evaluate the potential of its fibers for production of printing and writing paper grade pulp. The elephant grass was chemically and morphologically characterized and cooked by the soda process to two different degrees of delignification (kappa 17.5 and 10.6. The resulting pulps were fully bleached by the O-D*-(EP-D sequence and characterized for their beatability, drainability and physical-mechanical properties. The lignin content (20.2% was low, indicating that this grass should be easier to pulp. The morphological analyses of the elephant grass indicated a short fiber material, similar to hardwoods. The soda pulp from elephant grass cooked to kappa number 17.5 presented higher screened yield than 10.6 kappa pulp, with alkali demands of 15.0% and 20.0%, respectively. The total active chlorine required by the 17.5 and 10.6 kappa pulps, were 42.1 and 35.1 kg/odt pulp, respectively, to achieve an ISO brightness of approximately 90.0%. The bleached soda pulps cooked to 17.5 and 10.6 kappa number showed similar refinability and resistance to drainage, but the tensile and burst index were highest for the 17.5 kappa pulp at beating energy consumptions in the range of 0-6 Wh. It was concluded that both 10.6 and 17.5 kappa pulps from elephant grass are suitable for the production of printing and writing paper grade pulps, but the highest kappa 17.5 pulp is more economically attractive given its highest pulping yield, despite the significantly increased of chemical demand for bleaching A produção de papel para impressão e escrita Grau de celulose a partir de capim-elefante.

  17. A prospective study of the incidence of asymptomatic pulp necrosis following crown preparation.

    Science.gov (United States)

    Kontakiotis, E G; Filippatos, C G; Stefopoulos, S; Tzanetakis, G N

    2015-06-01

    To determine the incidence of asymptomatic pulp necrosis following crown preparation as well as the positive predictive value of the electric pulp testing. A total of 120 teeth with healthy pulps scheduled to receive fixed crowns (experimental teeth) were included. Teeth were divided into two groups according to the preoperative crown condition (intact teeth and teeth with preoperative caries, restorations or crowns) and into four groups according to tooth type (maxillary anterior teeth, maxillary posterior teeth, mandibular anterior teeth and mandibular posterior teeth). Experimental and control teeth were submitted to electric pulp testing on three different occasions before treatment commencement (stage 0), at the impression making session (stage 1) and just before the final cementation of the crown (stage 2). Teeth that were considered to contain necrotic pulps were submitted to root canal treatment. Upon access, absence of bleeding was considered as a confirmation of pulp necrosis. Data were analysed using bivariate (chi-square) and multivariate analysis (logistic regression). All reported probability values (P-values) were based on two-sided tests and compared to a significance level of 5%. The overall incidence of pulp necrosis was 9%. Intact teeth had a significantly lower incidence of pulp necrosis (5%) compared with preoperatively structurally compromised teeth (13%) [(OR: 9.113, P = 0.035)]. No significant differences were found amongst the four groups with regard to tooth type (P = 0.923). The positive predictive value of the electric pulp testing was 1.00. The incidence of asymptomatic pulp necrosis of teeth following crown preparation is noteworthy. The presence of preoperative caries, restorations or crowns of experimental teeth correlated with a significantly higher incidence of pulp necrosis. Electric pulp testing remains a useful diagnostic instrument for determining the pulp condition. © 2014 International Endodontic Journal. Published by

  18. Challenges of stem cell-based pulp and dentin regeneration: a clinical perspective.

    Science.gov (United States)

    Huang, George T-J; Al-Habib, Mey; Gauthier, Philippe

    2013-03-01

    There are two types of approaches to regenerate tissues: cell-based and cell-free. The former approach is to introduce exogenous cells into the host to regenerate tissues, and the latter is to use materials other than cells in an attempt to regenerate tissues. There has been a significant advancement in stem cell-based pulp and dentin regeneration research in the past few years. Studies in small and large animals have demonstrated that pulp/dentin-like tissues can be regenerated partially or completely in the root canal space with apical openings of 0.7-3.0 mm using dental pulp stem cells, including stem cells from apical papilla (SCAP) and subpopulations of pulp stem cells. Bone marrow mesenchymal stem cells (BMMSCs) and adipose tissue-derived MSCs (ADMSCs) have also been shown to regenerate pulp-like tissue. In contrast, the cell-free approach has not produced convincing evidence on pulp regeneration. However, one crucial concept has not been considered nor defined in the field of pulp/dentin regeneration and that is the critical size defect of dentin and pulp. Without such consideration and definition, it is difficult to predict or anticipate the extent of cell-free pulp regeneration that would occur. By reasoning, cell-free therapy is unlikely to regenerate an organ/tissue after total loss. Similarly, after a total loss of pulp, it is unlikely to regenerate without using exogenously introduced cells. A cell homing approach may provide a limited amount of tissue regeneration. Although stem cell-based pulp/dentin regeneration has shown great promise, clinical trials are difficult to launch at present. This article will address several issues that challenge and hinder the clinical applications of pulp/dentin regeneration which need to be overcome before stem cell-based pulp/dentin regeneration can occur in the clinic.

  19. Environmental performance of straw-based pulp making: A life cycle perspective.

    Science.gov (United States)

    Sun, Mingxing; Wang, Yutao; Shi, Lei

    2018-03-01

    Agricultural straw-based pulp making plays a vital role in pulp and paper industry, especially in forest deficient countries such as China. However, the environmental performance of straw-based pulp has scarcely been studied. A life cycle assessment on wheat straw-based pulp making in China was conducted to fill of the gaps in comprehensive environmental assessments of agricultural straw-based pulp making. On average, the global warming potential (GWP), GWP excluding biogenic carbon, acidification potential and eutrophication potential of wheat straw based pulp making are 2299kg CO 2 -eq, 4550kg CO 2 -eq, 16.43kg SO 2 -eq and 2.56kg Phosphate-eq respectively. The dominant factors contributing to environmental impacts are coal consumption, electricity consumption, and chemical (NaOH, ClO 2 ) input. Chemical input decrease and energy recovery increase reduce the total environmental impacts dramatically. Compared with wood-based and recycled pulp making, wheat straw-based pulp making has higher environmental impacts, which are mainly due to higher energy and chemical requirements. However, the environmental impacts of wheat straw-based pulp making are lower than hemp and flax based pulp making from previous studies. It is also noteworthy that biogenic carbon emission is significant in bio industries. If carbon sequestration is taken into account in pulp making industry, wheat straw-based pulp making is a net emitter rather than a net absorber of carbon dioxide. Since wheat straw-based pulp making provides an alternative for agricultural residue management, its evaluation framework should be expanded to further reveal its environmental benefits. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Wheat Bread with Pumpkin (Cucurbita maxima L. Pulp as a Functional Food Product

    Directory of Open Access Journals (Sweden)

    Renata Różyło

    2014-01-01

    Full Text Available In this study, a new application of pumpkin pulp in bread production is shown. The aim of this work is to determine the influence of the addition of fresh pumpkin pulp directly into wheat flour on physical, sensorial and biological properties of bread. The bioaccessibility of active compounds was also studied. An increase in the addition of pumpkin pulp from 5 to 20 % (converted to dry matter caused a decrease of bread volume and increase of crumb hardness and cohesiveness. The sensory characteristics of the bread showed that a partial replacement of wheat fl our with up to 10 % of pumpkin pulp gave satisfactory results. The taste, aroma and overall acceptability of control bread and bread containing 5 or 10 % of pulp had the highest degree of liking. The addition of higher levels of pumpkin pulp caused an unpleasant aroma and taste. Pumpkin pulp is a good material to complement the bread with potentially bioaccessible phenolics (including flavonoids and, especially, with peptides. The highest antioxidant activity was observed, in most cases, of the samples with added 10 and 15 % of pumpkin pulp. The addition of the pulp significantly enriched the bread with potentially bioaccessible angiotensin-converting enzyme (ACE inhibitors. The highest activity was determined in the bread with 15 and 20 % pumpkin pulp. ACE inhibitors from the tested bread were highly bioaccessible in vitro. Pumpkin pulp seems to be a valuable source of active compounds to complement the wheat bread. Adding the pulp directly to the wheat flour gives satisfactory baking results and reduces the cost of production. Additionally, pumpkin pulp is sometimes treated as waste material after the acquisition of seeds, thus using it as bread supplement also has environmental and economic benefi ts.

  1. Multivariate Analysis of Hemicelluloses in Bleached Kraft Pulp Using Infrared Spectroscopy.

    Science.gov (United States)

    Chen, Zhiwen; Hu, Thomas Q; Jang, Ho Fan; Grant, Edward

    2016-12-01

    The hemicellulose composition of a pulp significantly affects its chemical and physical properties and thus represents an important process control variable. However, complicated steps of sample preparation make standard methods for the carbohydrate analysis of pulp samples, such as high performance liquid chromatography (HPLC), expensive and time-consuming. In contrast, pulp analysis by attenuated total internal reflection Fourier transform infrared spectroscopy (ATR FT-IR) requires little sample preparation. Here we show that ATR FT-IR with discrete wavelet transform (DWT) and standard normal variate (SNV) spectral preprocessing offers a convenient means for the qualitative and quantitative analysis of hemicelluloses in bleached kraft pulp and alkaline treated kraft pulp. The pulp samples investigated include bleached softwood kraft pulps, bleached hardwood kraft pulps, and their mixtures, as obtained from Canadian industry mills or blended in a lab, and bleached kraft pulp samples treated with 0-6% NaOH solutions. In the principal component analysis (PCA) of these spectra, we find the potential both to differentiate all pulps on the basis of hemicellulose compositions and to distinguish bleached hardwood pulps by species. Partial least squares (PLS) multivariate analysis gives a 0.442 wt% root mean square errors of prediction (RMSEP) for the prediction of xylan content and 0.233 wt% RMSEP for the prediction of mannan content. These data all support the idea that ATR FT-IR has a great potential to rapidly and accurately predict the content of xylan and mannan for bleached kraft pulps (softwood, hardwood, and their mixtures) in industry. However, the prediction of xylan and mannan concentrations presented a difficulty for pulp samples with modified cellulose crystalline structure. © The Author(s) 2016.

  2. Effect of Bagasse Chemical Pulping and Coupling Agent on the Physical - Mechanical Properties of Composites Based on Bagasse pulp/Low density polyethylene

    Directory of Open Access Journals (Sweden)

    maryam allahdadi

    2016-12-01

    Full Text Available In this research, effect of reinforcing bagasse pulp and raw bagasse fibers and applying coupling agent MAPE (Maleic Anhydride Polyethylene on physical-mechanical properties of low density polyethylene (LDPE composites were studided. Fresh bagasse were collected from an experimental field in Khuzestan and after investigating anatomy and chemical properties of Different pulp fibers including monoethanolamine (MEA bagasse pulp, alkaline sulfite-anthraquinone (AS bagasse pulp, bleached soda (BS bagasse pulp, unbleached soda (UNS bagasse pulp and raw bagasse fibers (B were prepared. Then, composites with 30wt.% fiber content were manufactured by twin-screw extrusion followed by compression molding processing. The mechanical and physical properties of these composites were analyzed and compared. Results revealed that the chemical pulping dissolved a fraction of lignin and hemicelluloses so that the linkage potential and aspect ratio of bagasse fibers was improved and consequently, as compared with the raw bagasse fibers, bagasse pulp fibers have better reinforcing capability. The best overall properties were achieved with MEA and AS/AQ fibers. Addition of 5% (wt/wt of coupling agent MAPE resulted in a significant enhancement in the tensile strength, tensile modulus and impact strength in line with the improvement of the fiber-matrix interfacial adhesion making more effective the transfer of stress from the matrix to the rigid reinforcement.

  3. Influence of Soda Pulping Variables on Properties of Pineapple (Ananas comosus Merr. Leaf Pulp and Paper Studied by Face-Centered Composite Experimental Design

    Directory of Open Access Journals (Sweden)

    Jantharat Wutisatwongkul

    2016-01-01

    Full Text Available Face-centered composite design (FCC was used to study the effect of pulping variables: soda concentration (4-5 wt%, temperature (90–130°C, and pulping time (20–60 min on the properties of pineapple leaf pulp and paper employing soda pulping. Studied pulp responses were screened yield and lignin content (kappa number. Paper properties, which include tensile index, burst index, and tear index, were also investigated. Effects of the pulping variables on the properties were statistically analyzed using Minitab 16. The optimum conditions to obtain the maximum tensile index were soda concentration of 4 wt%, pulping temperature of 105°C, and pulping time of 20 min. The predicted optimum conditions provided tensile index, burst index, tear index, screened yield, and kappa number of 44.13 kN·m/kg, 1.76 kPa·m2, 1.68 N·m2/kg, 21.29 wt%, and 28.12, respectively, and were experimentally confirmed.

  4. Regenerative medicine using dental pulp stem cells for liver diseases.

    Science.gov (United States)

    Ohkoshi, Shogo; Hara, Hajime; Hirono, Haruka; Watanabe, Kazuhiko; Hasegawa, Katsuhiko

    2017-02-06

    Acute liver failure is a refractory disease and its prognosis, if not treated using liver transplantation, is extremely poor. It is a good candidate for regenerative medicine, where stem cell-based therapies play a central role. Mesenchymal stem cells (MSCs) are known to differentiate into multiple cell lineages including hepatocytes. Autologous cell transplant without any foreign gene induction is feasible using MSCs, thereby avoiding possible risks of tumorigenesis and immune rejection. Dental pulp also contains an MSC population that differentiates into hepatocytes. A point worthy of special mention is that dental pulp can be obtained from deciduous teeth during childhood and can be subsequently harvested when necessary after deposition in a tooth bank. MSCs have not only a regenerative capacity but also act in an anti-inflammatory manner via paracrine mechanisms. Promising efficacies and difficulties with the use of MSC derived from teeth are summarized in this review.

  5. Kraft pulp bleaching with molybdenum activated acid peroxide (PMo stage)

    International Nuclear Information System (INIS)

    Rabelo, Marcos Sousa

    2009-01-01

    Optimum conditions to run the P Mo stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H 2 O 2 . The P Mo stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P Mo stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

  6. Pulp tissue from primary teeth: new source of stem cells

    Directory of Open Access Journals (Sweden)

    Paloma Dias Telles

    2011-06-01

    Full Text Available SHED (stem cells from human exfoliated deciduous teeth represent a population of postnatal stem cells capable of extensive proliferation and multipotential differentiation. Primary teeth may be an ideal source of postnatal stem cells to regenerate tooth structures and bone, and possibly to treat neural tissue injury or degenerative diseases. SHED are highly proliferative cells derived from an accessible tissue source, and therefore hold potential for providing enough cells for clinical applications. In this review, we describe the current knowledge about dental pulp stem cells and discuss tissue engineering approaches that use SHED to replace irreversibly inflamed or necrotic pulps with a healthy and functionally competent tissue that is capable of forming new dentin.

  7. Preservation of mango and mango pulp by radiation

    International Nuclear Information System (INIS)

    Swailam, H.M.H.

    1998-01-01

    This study was carried out to investigate the following points: I- Effect of ionizing radiation alone (0-2 kGy) or in combination with hot water dip treatment (55 C/5 min.) on the shelf-life extension, chemical, microbiological, rheological and organoleptic properties of mango fruits (at mature green stage) stored at 12± 1 C. II - Effect of gamma radiation alone (0 -2 kGy) or with steam treatment (for 12 min.) on the chemical, microbiological, rheological and organoleptic properties of mango pulp stored at 3 ± 1 C. III- isolation , purification and identification of moulds associated with peel surface of mango fruits and yeasts associated with mango pulp as well as toxin production from some identified moulds

  8. Characterization of solid wastes from kraft pulp industry for ceramic materials development purposes

    International Nuclear Information System (INIS)

    Rodrigues, L.R.; Francisco, M.A.C.O.; Sagrillo, V.P.D.; Louzada, D.M.; Entringer, J.M.S.

    2016-01-01

    The Kraft pulp industry generates a large amount of solid wastes. Due this large quantity, the target of this study is characterize inorganic solid wastes, dregs, grits and lime mud, from the step of reagents recovery of Kraft process, aiming evaluate the potentiality of their use as alternative raw material on development of ceramic materials. Initially, the wastes were dried and ground, then they were subjected to the following characterization techniques: pH analysis, particle size analysis, X ray fluorescence, X ray diffraction, differential thermal analysis and thermogravimetric analysis and scanning electron microscopy. According to the results, it may be concluded that these wastes could be used as raw material in production of red ceramic and luting materials. (author)

  9. Moulded Pulp Manufacturing: Overview and Prospects for the Process Technology

    DEFF Research Database (Denmark)

    Didone, Mattia; Saxena, Prateek; Meijer, Ellen Brilhuis

    2017-01-01

    Eco-friendly packaging such as moulded pulp products have gained commercial importance in the recent years. However, it remains a greatly under-researched area, and there is an arising need to consolidate the best practices from research and industry in order to increase its implementation....... Moreover, based on the latest research in the field, an innovative drying technique that utilizes concepts derived from impulse drying is presented, and the implementation of this process technology is discussed....

  10. Bioconversion of sugar beet pulps and by-products

    Energy Technology Data Exchange (ETDEWEB)

    Lescure, J.P.; Bourlet, P.

    A new technology for biogas and energy supply by anaerobic digestion of wet vegetal substrats was studied. It was a two step anaerobic process, each resulting from numerous fermentative reactions. About 88% of the pulp substrat can be converted into gas and a volumic load of 7 kg.m/sup 3/ of dry solids was converted in 24 hours. Many technological problems were encountered with beet trash digestion. It was not tested with high loads, but bioconversion rate was about 75%.

  11. Microfibrillated cellulose from bamboo pulp and its properties

    International Nuclear Information System (INIS)

    Zhang, Junhua; Song, Hainong; Lin, Lu; Zhuang, Junping; Pang, Chunsheng; Liu, Shijie

    2012-01-01

    Microfibrillated cellulose (MFC) was obtained by disintegrating bleached kraft bamboo (Phyllostachys pubescens) pulp with a procedure of chemical pretreatment and high-pressure homogenization. The influences of sodium hydroxide dosage and homogenization times were evaluated by water retention value (WRV) of MFC. The properties, such as the surface morphology, rheological property and carboxyl acid content of MFC were also characterized using scanning electron microscope (SEM), rheometer and headspace gas chromatography (HS-GC) separately.

  12. The pulping of esparto grass by sodium monosulfite

    OpenAIRE

    Akchiche, Omar; Messaoud, Boureghda

    2007-01-01

    Traditionally, the esparto's limbs, in the manufacturing process of the cellulosic pulps, are delignified according to the process chlorinates alkaline which alternate the action of caustic's soda and chlorine; the reason is that these sheets cannot be free from the silica which they contain that only in strongly alkaline medium. In spite of the relative simplicity of implementation of this process, it does not remain free from grievance about it: low yield, an excessive consumption of bleach...

  13. Proteomic Analysis of Human Tooth Pulp: Proteomics of Human Tooth

    Czech Academy of Sciences Publication Activity Database

    Eckhardt, Adam; Jágr, Michal; Pataridis, Statis; Mikšík, Ivan

    2014-01-01

    Roč. 40, č. 12 (2014), s. 1961-1966 ISSN 0099-2399 R&D Projects: GA ČR(CZ) GA13-17224S; GA ČR(CZ) GAP206/12/0453; GA MZd(CZ) NT14324 Institutional support: RVO:67985823 Keywords : dentin * human pulp * tandem mass spectrometry * tooth proteome * 2-dimensional gel electrophoresis Subject RIV: FF - HEENT, Dentistry Impact factor: 3.375, year: 2014

  14. Bibliographic update work. Dental pulp sensory function. Pain.

    OpenAIRE

    Gomez, Natanael

    2011-01-01

    Dental pulp is a soft connective tissue type that thanks to its components can fulfill a number of vital functions to the tooth. Within these, the sensory function is of great interest since there is a close relationship between histomolecular tissue changes and clinical manifestations of odontogenic pain. To think about the painful history that the patient reports, knowing the tissue level events, helps to arrive to a correct diagnosis, treatment plan and prognosis. The aim of thi...

  15. Rapid determination of fluorine in the pulp process

    International Nuclear Information System (INIS)

    Ivanenko, V.V.; Kustov, V.N.; Levitskaya, O.N.

    1994-01-01

    The control of enrichment of mineral raw materials in order to increase the yield of enriched minerals is an important problem of modern industry. A possible solution is an automatic control system (ACS), which makes possible the monitoring and optimization of the enrichment. In terms of future applications, the nuclear-physical analysis, which is based on the use of a radionuclide source of neutrons, is a promising method. The advantages of this method (high rate, the possibility of performing the analysis directly in the flow, high accuracy, and high sensitivity) make themselves evident in the determination of short-lived isotopes, such as F, Ag, Si, Al, V, etc. Both an instrumental complex and a method for the rapid neutron activation determination (RNAD) of fluorine in the pulp flow of the enrichment process of raw materials were developed at the Institute of Chemistry, Far East Division, Russian Academy of Sciences. The analytical complex for RNAD comprises an activator; a densitometer; a pump; a pulp-feed system; a gamma-ray detector; a data acquisition apparatus; and a computer for processing the input/output data and controlling the analysis. The authors found that the RNAD of fluorine using radionuclide Pu-Be sources allows the determination in a 6-L pulp under recirculation conditions with an error of less than 1% in 3-5 minutes. The method allows the routine monitoring of the enrichment process of mineral raw materials

  16. ANTHRAQUINONE ADDITION IN THE ALKALINE PULPING OF Eucalyptus saligna

    Directory of Open Access Journals (Sweden)

    Lúcia Helena Jerônimo

    2009-10-01

    Full Text Available The present work evaluated different alkaline pulping conditions for Eucalyptus saligna wood. The objective was to evaluate the influence of the anthraquinone (AQ on the reduction of the total reduced sulfur (TRS in the aerial emissions, by reducing the sulfidity. The experiment consisted of 8 cooking with active alkali varying from  19 to 21%, sulfidity from  0 to 20% and anthraquinone from 0 to 0.1%, aiming to obtain  kappa numbers in the range 15.5±1.5. The H factor was used to control the relation time/temperature along cooking. The addition of anthraquinone increased the delignification rate allowing sulfidity reduction. The kraft/AQ pulping with sulfidities of 5 and 10% presented satisfactory results, making it possible the replacement of conventional kraft cooking, giving a reduction in process sulfidity without harms in pulping. In spite of a slightly lower performance, the soda/AQ cooking has potential to be used where the smell is a critical problem in the industrial operation.

  17. Strategies for characterizing compositions of industrial pulp and paper sludge

    Science.gov (United States)

    Aslanzadeh, Solmaz; Kemal, Rahmat A.; Pribowo, Amadeus Y.

    2018-01-01

    The large quantities of waste sludge produced by the pulp and paper industry present significant environmental challenges. In order to minimize the amounts of waste, the pulp sludge should be utilized for productive applications. In order to find feasible solutions, the sludge need to be characterized. In this study, the potential of using acid pretreatment and ashing method to determine the chemical compositions of the sludge is investigated. This study shows that acid pretreatment could be used to dissolve and determine the composition of CaCO3 in the pulp sludge. CaCO3 removal also facilitates the measurement of fiber and ash (clay) contents by using the ashing method. The optimum acid concentration used to completely dissolve CaCO3 was determined using a titration method. Using this method, the measurement of the chemical composition of the sludge sample revealed that it consisted primarily of CaCO3 (55% w/w), clay (25%, w/w), and fibers (18%, w/w). Based on these chemical compositions, potential utilization for the sludge could be determined.

  18. Dental Pulp: Correspondences and Contradictions between Clinical and Histological Diagnosis

    Science.gov (United States)

    Giuroiu, Cristian Levente; Căruntu, Irina-Draga; Lozneanu, Ludmila; Melian, Anca; Vataman, Maria; Andrian, Sorin

    2015-01-01

    Dental pulp represents a specialized connective tissue enclosed by dentin and enamel, the most highly mineralized tissues of the body. Consequently, the direct examination as well as pathological evaluation of dental pulp is difficult. Within this anatomical context, our study aimed to evaluate the correlation between dental pulp lesions and clinical diagnosis. Pulpectomies were performed for 54 patients with acute and chronic irreversible pulpitides and for 5 patients (control group) with orthodontic extractions. The morphological features were semiquantitatively assessed by specific score values. The clinical and morphological correspondence was noted for 35 cases (68.62%), whereas inconsistency was recorded for 16 cases (31.38%). The results of the statistical analysis revealed the correlations between clinically and pathologically diagnosed acute/chronic pulpitides. No significant differences were established between the score values for inflammatory infiltrate intensity, collagen depositions, calcifications and necrosis, and acute, respectively chronic pulpitides. We also obtained significant differences between acute pulpitides and inflammatory infiltrate and calcifications and between chronic pulpitides and inflammatory infiltrate, collagen deposition, and calcifications. On the basis of the predominant pathological aspects, namely, acute and chronic pulpitis, we consider that the classification schemes can be simplified by adequately reducing the number of clinical entities. PMID:26078972

  19. Preparation of lumen-loaded kenaf pulp with magnetite (Fe3O4)

    International Nuclear Information System (INIS)

    Zakaria, S.; Ong, B.H.; Ahmad, S.H.; Abdullah, M.; Yamauchi, T.

    2005-01-01

    Magnetic pulps were prepared from unbleached kenaf (hibiscus cannabinus L.) kraft pulps. Fe 3 O 4 or magnetite powder was used to load into the pulp's lumen and pit. Aluminum sulphate [Al 2 (SO 4 ) 3 ] (alum) and polyethylenimine (PEI), both mainly function as retention aid were used throughout the experiment and found to be beneficial in the preparation of this magnetic pulps. The ash content method was used to determine the amount of magnetite retained in the lumen and pit. The utilization of PEI up to 2% per pulp fibres was found to be the best result on lumen loading. The deposition of magnetite powder in lumen and pit is found decrease as the addition of PEI used is more than 2% per pulp fibres. Scanning electron microscope (SEM) clearly shows the distribution of magnetite deposited in the lumen. Tensile index and folding endurance of the loaded fibre decreased slightly as the percentage of loading pigment increased

  20. Factors affecting the optimal performance of a high-yield pulping operation

    Energy Technology Data Exchange (ETDEWEB)

    Broderick, G [Noranda Technology Centre, Pointe-Claire, PQ (Canada); Paris, J [Ecole Polytechnique, Montreal, PQ (Canada); Valada, J L [Quebec Univ., Trois-Rivieres, PQ (Canada)

    1995-06-01

    Strategies for operating a chemical-mechanical pulp mill were investigated from data based on process models from some one hundred pilot scale pulping runs. Optimal values for 55 process and pulp quality variables have been calculated by applying a genetic algorithm search to a fuzzy model of the overall system. Best pulp quality was achieved and maintained when the chemical pretreatment was conducted at moderately low temperatures using a high SO{sub 2} concentration, which produced high sulphonation and high yield at the same time. By characterizing the quality of the pulp at the fibre level, optimization results were said to be more easily transferable to other high yield pulping systems. 19 refs., 6 tabs.

  1. Recycling cellulase towards industrial application of enzyme treatment on hardwood kraft-based dissolving pulp.

    Science.gov (United States)

    Wang, Qiang; Liu, Shanshan; Yang, Guihua; Chen, Jiachuan; Ji, Xingxiang; Ni, Yonghao

    2016-07-01

    Cost-effectiveness is vital for enzymatic treatment of dissolving pulp towards industrial application. The strategy of cellulase recycling with fresh cellulase addition was demonstrated in this work to activate the dissolving pulp, i.e. decreasing viscosity and increasing Fock reactivity. Results showed that 48.8-35.1% of cellulase activity can be recovered from the filtered liquor in five recycle rounds, which can be reused for enzymatic treatment of dissolving pulp. As a result, the recycling cellulase with addition fresh cellulase of 1mg/g led to the pulp of viscosity 470mL/g and Fock reactivity 80%, which is comparable with cellulase charge of 2mg/g. Other pulp properties such as alpha-cellulose, alkaline solubility and molecular weight distribution were also determined. Additionally, a zero-release of recycling cellulase treatment was proposed to integrate into the dissolving pulp production process. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Alkaline pulping with additives of date palm rachis and leaves from Sudan.

    Science.gov (United States)

    Khristova, P; Kordsachia, O; Khider, T

    2005-01-01

    Soda-anthraquinone (soda-AQ), alkaline sulphite-anthraquinone (AS-AQ) and alkaline sulphite-anthraquinone-methanol (ASAM) pulping of date palm rachis and leaves from Sudan was carried under different conditions, and pulps with variable yields and mechanical properties were obtained. The date palm rachis gave best yields and mechanical properties with the AS-AQ or the ASAM process, while the leaves were best pulped with the soda method with low yield, but very good strength properties. Blending with 10% and 30% kenaf bark pulp was beneficial, especially for the AS-AQ pulps. Totally chlorine free (TCF) bleached rachis pulps were obtained of high brightness and strength properties suitable for use in writing and printing papers.

  3. Steam drying compared to drum drying markedly increases early phase rumen fermentability of sugar beet pulp

    DEFF Research Database (Denmark)

    Nielsen, Mette Olaf; Larsen, Kasper; Jensen, Arne Sloth

    2017-01-01

    Freshly pressed and dried sugar beet pulp was sampled from 2 different factories located within a distance of 30 km and on 4 different dates. One factory was equipped with a steam dryer and the other with a drum dryer. A recognized in vitro technique was used to establish, how the drying process...... affected rumen fermentability of the pulp, since fibrous feeds (such as sugar beet pulp) rely on microbial fermentation in the rumen to be digestible to the cow. Steam dried pulp had a remarkable >60% higher fermentability compared to drum dried pulp during the first 12(-15) hours of fermentation...... (such as pectin) and small particles as low as 6.7-13.3 hours. Future feeding trials are needed to establish exactly how much the feeding value is increased in steam dried sugar beet pulp....

  4. De-pulping and Seed Separation from Tumba ( Citrullus colocynthis) Fruit

    Science.gov (United States)

    Mudgal, Vishvambhar Dayal

    2017-09-01

    Tumba ( Citrullus colocynthis) contains spongy pulp in which seeds are embedded unevenly. Seeds contain about 26% fats and 13% protein. The process of seed separation is highly time consuming and labour intensive. Two weeks are required to separate its seeds with traditional methods. The developed prototype, for separating tumba seeds, mainly consists of chopper, de-pulping screw, barrel assembly and seed separation unit. The de-pulping screw and barrel assembly was divided in two sections i.e. conveying (feeding zone) and compression sections (de-pulping zone). The performance of developed machine was evaluated at different screw speed in the range of 40-100 rpm. Maximum pulp removal efficiency of 78.1% was achieved with screw speed of 60 rpm. Seed separation from the pulp was carried out by adding different chemicals. Use of sodium hydroxide and potassium hydroxide produced seed separation up to 99%.

  5. Raw data used to generate figures 2 through 6 in Biological Responses of Raw 264.7 Macrophage Exposed to Two Strains of Stachybotrys chartarum Spores Grown on Four Different Wallboard Types manuscript.

    Data.gov (United States)

    U.S. Environmental Protection Agency — Excel files containing raw data used to generate figures throughout manuscript. This dataset is associated with the following publication: Dean , T., D. Betancourt ,...

  6. Selective degradation of lignin and elimination of HO radicals in pulps by O3 and UV laser flash irradiation

    Institute of Scientific and Technical Information of China (English)

    林鹿; 周贤涛; 邱玉桂

    2002-01-01

    HO radical is an aggressive reagent to abstract hydrogen from diverse substitutes and lead them to degradation, however, in reaction of active oxygen species with lignins, complex phenolic polymers, in dispersed lignocellulose such as pulp for environment-benign delignification, HO radicals should be eliminated as more as possible to prevent cellulose from unfavorably concomitant degradation. A reaction system of O3 is constructed under UV laser flash irradiation, and HO radicals are controlled efficiently by it. A new mechanism is proposed, for the first time, that O radicals generated from reaction of O3 with UV laser flash irradiation might be the contributor to scavenge HO radicals.

  7. Sugar, acid and furfural quantification in a sulphite pulp mill: Feedstock, product and hydrolysate analysis by HPLC/RID

    Directory of Open Access Journals (Sweden)

    Tamara Llano

    2017-09-01

    The analysis of major and minor monosaccharides, aliphatic carboxylic acids and furfurals has been optimised. An important drawback of the spent liquors generated after sulphite pulping is their acidic nature, high viscosity and adhesive properties that interfere in the column lifetime. This work recommends both a CHO-782Pb column for the sugar analysis and an SH-1011 resin-based cross-linked gel column to separate low-molecular-weight chain acids, alcohols and furfurals. Such columns resulted in a good separation with long lifetime, wide pH operating range and low fouling issues.

  8. Wheat Bread with Pumpkin (Cucurbita maxima L.) Pulp as a Functional Food Product

    OpenAIRE

    Renata Różyło; Dariusz Dziki; Anna Jakubczyk; Monika Karaś; Urszula Gawlik-Dziki; Krzysztof Różyło

    2014-01-01

    In this study, a new application of pumpkin pulp in bread production is shown. The aim of this work is to determine the influence of the addition of fresh pumpkin pulp directly into wheat flour on physical, sensorial and biological properties of bread. The bioaccessibility of active compounds was also studied. An increase in the addition of pumpkin pulp from 5 to 20 % (converted to dry matter) caused a decrease of bread volume and increase of crumb hardness and cohesiveness. The sensory chara...

  9. Understanding the Nature and Reactivity of Residual Lignin for Improved Pulping and Bleaching Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Yuan-Zong Lai

    2001-11-30

    One of the most formidable challenges in kraft pulping to produce bleached chemical pulps is how to effectively remove the last 5-10% of lignin while maintaining the fiber quality. To avoid a severe fiber degradation, kraft pulping is usually terminated in the 25-30 kappa number range and then followed by an elementally chlorine free (ECF) or a totally chlorine free (TCF) bleaching sequence to reduce the environmental impacts.

  10. Understanding the Nature and Reactivity of Residual Lignin for Improved Pulping and Bleaching Efficiency; FINAL

    International Nuclear Information System (INIS)

    Yuan-Zong Lai

    2001-01-01

    One of the most formidable challenges in kraft pulping to produce bleached chemical pulps is how to effectively remove the last 5-10% of lignin while maintaining the fiber quality. To avoid a severe fiber degradation, kraft pulping is usually terminated in the 25-30 kappa number range and then followed by an elementally chlorine free (ECF) or a totally chlorine free (TCF) bleaching sequence to reduce the environmental impacts

  11. Process parameters affecting the delignification of eucalyptus kraft pulp with peroxyacetic acid

    Directory of Open Access Journals (Sweden)

    Chandranupap, P.

    2004-11-01

    Full Text Available Various process parameters affecting eucalyptus kraft pulp delignification with peroxyacetic acid were investigated. The results showed that pH was an important factor. The delignification rate increased with increasing pH to the value of 6. High delignification rate was obtained when the pulp was chelated with Na4-EDTA prior to the peroxyacetic acid stage. Therefore, delignification reaction rate depends on peroxyacid charge, temperature, pH and metal content of pulp.

  12. EFFECTS OF ALKALINE PRE-IMPREGNATION AND PULPING ON MALAYSIA CULTIVATED KENAF (HIBISCUS CANNABINUS

    OpenAIRE

    Lin Suan Ang; Cheu Peng Leh; Chong Chat Lee

    2010-01-01

    This study was carried out to identify an appropriate alkaline pulping condition for Malaysia cultivated kenaf (Hibiscus cannabinus L.). The chemical composition of the kenaf bast and core fibers, and also whole stalk with different growing time were examined prior to pulping attempts. The results of various soda-AQ pulping showed that the degree of carbohydrate degradation and delignification increased with the increase of active alkali and cooking temperature, but decreased with the increas...

  13. Distinctive genetic activity pattern of the human dental pulp between deciduous and permanent teeth.

    Directory of Open Access Journals (Sweden)

    Ji-Hee Kim

    Full Text Available Human deciduous and permanent teeth exhibit different developmental processes, morphologies, histological characteristics and life cycles. In addition, their pulp tissues react differently to external stimuli, such as the pulp sensitivity test, dental trauma and pulp therapy materials. These suggest differences in gene expression and regulation, and in this study we compared gene-expression profiles of the human dental pulp from deciduous and permanent teeth. Pulp tissues from permanent premolars and deciduous molars aged 11-14 years were extirpated and mRNA was isolated for cDNA microarray analysis, and quantitative real-time PCR (qPCR. Other teeth were used for immunohistochemical analysis (IHC. Microarray analysis identified 263 genes with a twofold or greater difference in expression level between the two types of pulp tissue, 43 and 220 of which were more abundant in deciduous and permanent pulp tissues, respectively. qPCR analysis was conducted for eight randomly selected genes, and the findings were consistent with the cDNA microarray results. IHC confirmed that insulin-like growth factor 2 mRNA-binding protein 1 (IGF2BP1 was broadly expressed in deciduous dental pulp tissue, but minimally expressed in permanent dental pulp tissue. Immunohistochemical analysis showed that calbindin 1 (CALB1, leucine-rich repeat-containing G-protein-coupled receptor 5 (LGR5, and gamma-aminobutyric acid A receptor beta 1 (GABRB1 were abundantly expressed in permanent predentin/odontoblasts, but only minimally expressed in deciduous dental pulp tissue. These results show that deciduous and permanent pulp tissues have different characteristics and gene expression, suggesting that they may have different functions and responses to therapies focused on pulp or dentin regeneration.

  14. Distinctive genetic activity pattern of the human dental pulp between deciduous and permanent teeth.

    Science.gov (United States)

    Kim, Ji-Hee; Jeon, Mijeong; Song, Je-Seon; Lee, Jae-Ho; Choi, Byung-Jai; Jung, Han-Sung; Moon, Seok Jun; DenBesten, Pamela K; Kim, Seong-Oh

    2014-01-01

    Human deciduous and permanent teeth exhibit different developmental processes, morphologies, histological characteristics and life cycles. In addition, their pulp tissues react differently to external stimuli, such as the pulp sensitivity test, dental trauma and pulp therapy materials. These suggest differences in gene expression and regulation, and in this study we compared gene-expression profiles of the human dental pulp from deciduous and permanent teeth. Pulp tissues from permanent premolars and deciduous molars aged 11-14 years were extirpated and mRNA was isolated for cDNA microarray analysis, and quantitative real-time PCR (qPCR). Other teeth were used for immunohistochemical analysis (IHC). Microarray analysis identified 263 genes with a twofold or greater difference in expression level between the two types of pulp tissue, 43 and 220 of which were more abundant in deciduous and permanent pulp tissues, respectively. qPCR analysis was conducted for eight randomly selected genes, and the findings were consistent with the cDNA microarray results. IHC confirmed that insulin-like growth factor 2 mRNA-binding protein 1 (IGF2BP1) was broadly expressed in deciduous dental pulp tissue, but minimally expressed in permanent dental pulp tissue. Immunohistochemical analysis showed that calbindin 1 (CALB1), leucine-rich repeat-containing G-protein-coupled receptor 5 (LGR5), and gamma-aminobutyric acid A receptor beta 1 (GABRB1) were abundantly expressed in permanent predentin/odontoblasts, but only minimally expressed in deciduous dental pulp tissue. These results show that deciduous and permanent pulp tissues have different characteristics and gene expression, suggesting that they may have different functions and responses to therapies focused on pulp or dentin regeneration.

  15. The expressions of NF-kb and TGFb-1 on odontoblast-like cells of human dental pulp injected with propolis extracts

    Directory of Open Access Journals (Sweden)

    Ira Widjiastuti

    2014-03-01

    Full Text Available Background: Propolis is known to have beneficial effects, namely anti- bacterial, anti-viral, anti-inflammatory, antioxidant, and immunomodulatory. Propolis extracts with anti-inflammatory properties are expected to be useful in treating inflamed pulp tissue with a diagnosis of reversible pulpitis. The inflammation of pulp tissue is caused by bacteria, namely Lactobacillus acidophilus. This research used odontoblast like cells derived from pulp tissue of human third molars. Odontoblast like cells exposed to Lactobacillus achidophilus were used as a model of proinflammatory cytokine signaling. This research examined the effects of propolis extracts on odontoblast like cells exposed to Lactobacillus acidophilus. Purpose: This research was aimed to determine the effectiveness of propolis extracts on the activities of odontoblast-like cells exposed to Lactobacillus acidophillus by measuring the expressions of NFkb and TGF- b1. Methods: First, pulp odontoblast cultures were derived from human dental pulp tissues of impacted third molars removed by using digestion method. Next, odontoblast-like cells exposed to inactive Lactobacillus acidophilus bacteria were given propolis extract. Finally, the activities of odontoblast-like cells were monitored by measuring the expressions of NF-kb and TGFb-1 with immunocytochemistry technique. Results: A decline NF-kb expression and on increase of TGFb-1 expression on odontoblast like cells exposed to inactive Lactobacillus acidophilus. Conclusion: Propolis extracts inhibit the expression of NF-kb, and increase the expression of TGF-b1 in pulp odontoblast-like cells exposed to inactive Lactobacillus acidophillus.Latar belakang: Propolis dilaporkan mempunyai efek menguntungkan yaitu bersifat anti bakteri, anti virus, anti inflamasi, anti oksidan, dan imunomodulator. Ekstrak propolis dengan sifat anti inflamasi diharapkan bermanfaat untuk mengobati jaringan pulpa yang mengalami inflamasi dengan diagnosis pulpitis

  16. PROCESS FOR THE PRODUCTION OF DISSOLVING PULP FROM TREMA ORIENTALIS (NALITA) BY PREHYDROLYSIS KRAFT AND SODA-ETHYLENEDIAMINE (EDA) PROCESS

    OpenAIRE

    M. A. Quaiyyum; A. Noori; Labooni Ahsan; M. Sarwar Jahan

    2008-01-01

    This paper presents a preliminary study for the production of dissolving pulp from Trema orientalis (Nalita). Water prehydrolysis kraft and soda-ethylenediamine (EDA) pulping for the production of dissolving pulp from T. orientalis was investigated. Prehydrolysis at 150 and 170 oC did not produce pulp with high α-cellulose content when using the kraft process. But addition of 0.25 % H2SO4 in prehydrolysis liquor increased the purity of the pulp with the sacrifice of pulp yield and viscosity. ...

  17. Characteristics and utilization of non-wood pulp and paper; Himokuzai pulp / kami no tokucho to sono riyo

    Energy Technology Data Exchange (ETDEWEB)

    Hara, H. [Mishima Paper Co. Ltd., Shizuoka (Japan)

    1998-09-01

    The reasons, difficulty in the usage, and the methods of use of non-wood papers are discussed. Non-wood papers sold in Japan are arranged basing on published data. The type of non-wood paper classified as special printing paper makes up the majority, and there are a variety of other products such as printing board, coated paper, thin paper, wrapping paper, functional paper, and watercolor paper. Kenaf and cotton are used in large quantities as non-wood plants for paper production, and use of bagasse and bamboo is increasing. Non-wood paper are used in consideration of environmental and resources problems and for utilizing the special features of non-wood fiber, and the characteristics of non-wood pulp and the effect of non-wood paper are discussed in this report. It is expected that papers utilizing the characteristics of non-wood paper will be developed. Non-wood papers are substitutions for various papers produced from wood pulp, and the fundamental point is the method of improving the original quality and paper quality by combining with non-wood pulp. 11 refs., 4 figs., 3 tabs.

  18. Effect of Flotation Time on the Deinking Process and Properties of Deinked Pulp

    Directory of Open Access Journals (Sweden)

    Sami İmamoğlu

    2012-11-01

    Full Text Available This paper discusses the influence of flotation time on the ink removal and physical properties of resulting deinked pulp. Flotation deinking of high quality office paper, printed in a digital duplicating machine based on screen-printing system, was studied using a laboratory cell with a nominal capacity of 10 L. Formamidine sulfinic acid was used in a pulper and pulping conditions such as temperature, retention time, chemical dosage and consistency were held constant prior to flotation process. During the flotation process while pulp consistency, agitation speed, air flow rate and other conditions keeping constant, only flotation time were analyzed in terms of physical properties of resulting pulp quality, pulp yield, filler and fibre balance and waste water quality aspects at 0, 3, 6, 9, 12 and 15 minutes. Increased flotation time substantially affected optical properties of pulp up to some point then became steady. Yield losses increased as might be expected with increasing flotation time by the 9th minute as flotation sludge skimmed off on top of the flotation cell. Filler content of flotation sludge increased with increasing flotation time while fibre content was decreasing to a certain extent. Thanks to removal of ink and filler materials from pulp physical properties of evaluated handsheets enhanced. The overall results demonstrate that increasing flotation time increased physical and optical properties of resulting pulp. On the other hand flotation time should be increased up to critical point. Exceeding critical point increased yield losses, consumed time and energy without gaining significant pulp qualities.

  19. Effect of Partial Pre-Extraction of Hemicelluloses on the Properties of Pinus radiata Chemimechanical Pulps

    Directory of Open Access Journals (Sweden)

    Pablo Reyes

    2015-09-01

    Full Text Available Extraction of hemicelluloses prior to pulping and conversion of the extracted hemicelluloses to other bioproducts could provide additional revenue to traditional pulp and paper industries. The effect of hemicelluloses pre-extraction with a hydrothermal (HT process on Pinus radiata chemimechanical pulp (CMP properties was investigated in this study. The HT extraction resulted in a release of 7% to 58% of the initial amount of hemicelluloses from the wood. The extraction yield increased with temperature and extraction time. This hemicellulosic fraction was in the form of low molar mass oligomers with molecular weights varying from 1.5 to 100 kDa. Compared with the control (unextracted CMP pulp, the HT pre-extraction significantly reduced the refining energy to obtain a given fibrillation degree (freeness. The pulp yield with the HT/CMP process was in the range of 56% to 75%. Fiber properties of the pulps from pre-extracted wood, such as fiber length, were reduced, while increases in fiber width, fines content, fiber coarseness, and kink index were observed in comparison with the control pulps. The strength properties of CMP pulps decreased with increasing amounts of hemicellulose removal during the stage prior to pulping.

  20. Nutritional composition of Annona crassiflora pulp and acceptability of bakery products prepared with its flour

    OpenAIRE

    Villela,Paula; Batista,Ângela Giovana; Dessimoni-Pinto,Nísia Andrade Villela

    2013-01-01

    Annona crassiflora offers an edible fruit native to the Savanna. This study aimed to develop a flour meal from Annona crassiflora pulp; analyze the chemical composition of the fresh pulp and its flour; develop and verify the acceptance of formulations with different concentrations of the flour of Annona crassiflora pulp. Fruit used were selected and processed. The pulp was dried in an oven at 60-65 ºC/48h. We analyzed the chemical composition, and two formulations of breads were prepared with...

  1. Substance P and CGRP expression in dental pulps with irreversible pulpitis.

    Science.gov (United States)

    Sattari, Mandana; Mozayeni, Mohammad Ali; Matloob, Arash; Mozayeni, Maryam; Javaheri, Homan H

    2010-08-01

    The purpose of this study was to compare substance P (SP) and calcitonin gene-related peptide (CGRP) expression in pulp tissue with clinically diagnosed symptomatic and asymptomatic irreversible pulpitis. Healthy pulps acted as controls. Five normal pulps and 40 with irreversible pulpitis (20 symptomatic and 20 asymptomatic) were obtained from 45 different patients. SP and CGRP expression was determined by competition binding assays using enzyme immunoassay. anova and Mann-Whitney tests were used to ascertain if there were statistically significant differences between the groups. The results showed that neuropeptides were found in all pulp samples. The highest and the lowest expressions for SP and CGRP were found in symptomatic irreversible pulpitis and healthy pulps groups, respectively. The differences between healthy pulps and the groups of pulps having irreversible pulpitis were significant (P pulpitis groups (P pulpitis groups were not significant. This study demonstrated that the expression of CGRP and SP is significantly higher in pulps with irreversible pulpitis compared with healthy pulps.

  2. Biodegradation behaviors and color change of composites based on type of bagasse pulp/polylactic acid

    Directory of Open Access Journals (Sweden)

    maryam allahdadi

    2017-05-01

    Full Text Available In this research, appearance quality and decay resistance of polylactic acid (PLA based green composites made from monoethanolamine (MEA bagasse pulp, alkaline sulfite-anthraquinone (AS bagasse pulp, bleached soda (B S bagasse pulp, unbleached soda (UN S bagasse pulp (UN S bagasse pulp and raw bagasse fibers (B were investigated. For the investigation of biodegradation behaviors, effect of the white rot fungi (Coriolus versicolor on the neat PLA and composites with natural fibers during 30 and 60 days were studied. It is found that when the bagasse fibers were incorporated into composites matrix, percentage weight reduction and stiffness of samples have been increased. Also, the rate of loss mentioned of the composites made from bagasse pulp fibers were superior to the relevant raw bagase fibers. This can be explained by the removal of non-cellulosic components such as lignin and hemicelluloses from the fibers by pulping process. Also, the results indicates the inferior of surface qualities of fabricated composites regarding to neat PLA. Depending on the fiber type, different reductions of the surface qualities were attained. However, the degree of color change of the composites with any type of bagasse pulp fibers were lower compared with composite with raw bagasse fiber. Finally, as compared with the raw bagasse fibers, bagasse pulp fibers have better reinforcing capability.

  3. Local myogenic pulp-derived cell injection enhances craniofacial muscle regeneration in vivo.

    Science.gov (United States)

    Jung, J E; Song, M J; Shin, S; Choi, Y J; Kim, K H; Chung, C J

    2017-02-01

    To enhance myogenic differentiation in pulp cells isolated from extracted premolars by epigenetic modification using a DNA demethylation agent, 5-aza-2'-deoxycytidine (5-Aza), and to evaluate the potent stimulatory effect of 5-Aza-treated pulp cell injection for craniofacial muscle regeneration in vivo. Pulp cells were isolated from premolars extracted for orthodontic purposes from four adults (age range, 18-22.1 years). Levels of myogenic differentiation and functional contraction response in vitro were compared between pulp cells with or without pre-treatment of 5-Aza. Changes in muscle regeneration in response to green fluorescent protein (GFP)-labelled myogenic pulp cell injection in vivo were evaluated using a cardiotoxin (CTX)-induced muscle injury model of the gastrocnemius as well as the masseter muscle in mice. Pre-treatment of 5-Aza in pulp cells stimulated myotube formation, myogenic differentiation in terms of desmin and myogenin expression, and the level of collagen gel contraction. The local injection of 5-Aza pre-treated myogenic pulp cells was engrafted into the host tissue and indicated signs of enhanced muscle regeneration in both the gastrocnemius and the masseter muscles. The epigenetic modification of pulp cells from extracted premolars and the local injection of myogenic pulp cells may stimulate craniofacial muscles regeneration in vivo. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Efficient energy conversion in the pulp and paper industry: application to a sulfite wood pulping process

    Energy Technology Data Exchange (ETDEWEB)

    Marechal, F.

    2007-07-01

    This report measures the actions performed in 2006 and the actions planned for 2007 within the framework of the project Efficient Energy Conversion in the Pulp and Paper Industry. In addition to the data reconciliation models of the steam and condensate networks and of the process of Borregaard Schweiz AG, process models have been developed with the goal of defining the heat requirements of the process. The combination of utility system data reconciliation with the process models allows to considerably reduce the need for detailed process modelling and for on-site data collection and measurement. A systematic definition of the hot and cold streams in the process has been developed in order to compute the minimum energy requirement of the process. The process requirements have been defined using the dual representation concept where the energy requirement of the process unit operations are systematically analysed from their thermodynamic requirement and the way they are satisfied by the technology that implements the operation. Corresponding to the same energy requirement but realised with different temperature allows on one hand to define the exergy efficiency of the heat transfer system in each of the process unit operations and to identify possible energy savings by heat exchange in the system. The analysis has been completed by the definition of the possible energy recovery from waste streams. The minimum energy requirement of the process using the different requirement representation has been realised and the analysis of the energy savings opportunities is now under preparation. This new step will first concern the definition of the utility system integration and the systematic analysis of the energy savings opportunities followed by the techno-economic evaluation of the most profitable energy savings options in the process. The national and international collaborations constitute also an important part of this project. The project is done in close

  5. Biological response of pulps submitted to different capping materials Resposta biológica de polpas submetidas a diferentes materiais capeadores

    Directory of Open Access Journals (Sweden)

    André Luiz Fraga Briso

    2006-09-01

    Full Text Available Pulp capping is a procedure that comprises adequate protection of the pulp tissue exposed to the oral environment, aiming at the preservation of its vitality and functions. This study evaluated the response of the dental pulps of dog teeth to capping with mineral trioxide aggregate (MTA or calcium hydroxide P.A. For that purpose, 37 teeth were divided into two groups, according to the capping material employed. Two dogs were anesthetized and, after placement of a rubber dam, their pulps were exposed in a standardized manner and protected with the experimental capping materials. The cavities were then sealed with resin-modified glass ionomer cement and restored with composite resin. After sixty days, the animals were killed and the specimens were processed in order to be analyzed with optic microscopy. It was observed that MTA presented a higher success rate compared to calcium hydroxide, presenting a lower occurrence of infection and pulp necrosis.O capeamento pulpar é um procedimento que consiste na adequada proteção do tecido pulpar exposto ao meio oral, objetivando a preservação de sua vitalidade e suas funções. O objetivo deste trabalho foi observar a resposta da polpa dental de cães ao capeamento com o agregado de trióxido mineral (MTA ou hidróxido de cálcio P.A. Para tanto, 37 dentes foram divididos em dois grupos, de acordo com o material capeador utilizado. Dois cães foram anestesiados e após o isolamento absoluto do campo operatório, realizou-se exposição padronizada da polpa, proteção com os materiais capeadores testados e selamento das cavidades com cimento modificado de ionômero de vidro. Os dentes foram então restaurados com resina composta. Após sessenta dias, os animais foram sacrificados e as peças foram processadas para a análise microscópica dos dentes. Observou-se que o MTA apresentou maior índice de sucesso em relação ao hidróxido de cálcio, evidenciando menor ocorrência de infecção e necrose

  6. MTA and calcium hydroxide for pulp capping MTA e hidróxido de cálcio para proteção pulpar direta

    Directory of Open Access Journals (Sweden)

    Alexandra Mussolino de Queiroz

    2005-06-01

    Full Text Available This study evaluated the biocompatibility of mineral trioxide aggregate (MTA after direct capping of exposed pulp tissue in dog's teeth. Class I cavities were prepared in 26 teeth from 3 adult dogs. MTA was applied over the exposed pulp in 13 teeth and paste of calcium hydroxide plus distilled water (control was applied in the remaining 13 teeth. After 90 days, the animals were killed; the maxilla and mandible were dissected and sectioned to obtain individual roots. The samples were processed histologically. The pulp and periapical response observed with the use of MTA was similar to that of calcium hydroxide paste. In all specimens, there was a dentin bridge obliterating the exposure, an intact odontoblastic layer, no inflammatory cells, normal connective pulp tissue, normal apical and periapical regions and no bone tissue changes. Similar to calcium hydroxide, MTA presented excellent response when used for direct pulp capping.O objetivo deste trabalho foi avaliar a biocompatibilidade do agregado de trióxido mineral (MTA, após proteção pulpar direta em dentes de cães. Foram preparadas cavidades de Classe I, em 26 dentes de 3 cães adultos. O MTA foi aplicado sobre 13 dentes e a pasta de hidróxido de cálcio (grupo controle foi aplicada sobre os 13 dentes remanescentes. Após 90 dias, os animais foram mortos, a maxila e a mandíbula foram dissecadas e os dentes foram seccionados para obtenção de raízes individualizadas. Os espécimes foram processados histologicamente. A resposta do tecido pulpar e periapical foi semelhante para o MTA e o hidróxido de cálcio. Em todos os espécimes havia ponte de dentina obliterando o local da exposição pulpar, camada odontoblástica íntegra, ausência de células inflamatórias, tecido pulpar normal, e ausência de alterações na região periapical e óssea. Da mesma maneira que o hidróxido de cálcio, o MTA apresentou excelente biocompatibilidade quando usado para proteção pulpar direta.

  7. Proliferation and mineralization ability of dental pulp cells derived from primary and permanent teeth

    Directory of Open Access Journals (Sweden)

    Suttatip Kamolmatyakul

    2011-04-01

    Full Text Available The aims of this study were to compare the proliferation and mineralization ability of CFU-F selected dental pulp cellsderived from primary and permanent teeth. Those cells were isolated by enzyme digestion and analyzed for their colonyformingcapacity. The cell proliferation was measured by the MTT assay on day 1, day 7, and day14. Alizarin Red S stainingwas used to detect mineralized nodule formation of the cells on day 7, 14, 21, and 28. Proliferation of CFU-F selected pulpcells from primary teeth was significantly higher than that of CFU-F selected pulp cells from permanent teeth in all periods ofthe experiment. Upon cultured cells in mineralization inducing media, the mineralized nodules appeared as early as day 14 inCFU-F selected pulp cells from primary teeth and MG-63, whereas those of CFU-F selected pulp cells from permanent teethcan be found at day 21. On day 21 and day 28, the mineralized nodules of the CFU-F selected pulp cells from the primaryteeth group were more than those in the CFU-F selected pulp cells from the permanent teeth group. Mineralized noduleformation in the CFU-F selected pulp cells from the permanent teeth group appeared later and were less than those ofCFU-F selected pulp cells from primary teeth. However, mineralized nodules in CFU-F selected pulp cells from the permanentteeth group increased very fast after their appearance. Those results suggest that CFU-F selected pulp cells from primaryteeth had a higher proliferation rate and mineralization rate when compared to CFU-F selected pulp cells from permanentteeth.

  8. Characterization of stem and progenitor cells in the dental pulp of erupted and unerupted murine molars

    Science.gov (United States)

    Balic, Anamaria; Aguila, H. Leonardo; Caimano, Melissa J.; Francone, Victor P.; Mina, Mina

    2010-01-01

    In the past few years there have been significant advances in the identification of putative stem cells also referred to as “mesenchymal stem cells” (MSC) in dental tissues including the dental pulp. It is thought that MSC in dental pulp share certain similarities with MSC isolated from other tissues. However, cells in dental pulp are still poorly characterized. This study focused on the characterization of progenitor and stem cells in dental pulps of erupted and unerupted mice molars. Our study showed that dental pulps from unerupted molars contain a significant number of cells expressing CD90+/CD45-, CD117+/CD45-, Sca-1+/CD45- and little if any CD45+ cells. Our in vitro functional studies showed that dental pulp cells from unerupted molars displayed extensive osteo-dentinogenic potential but were unable to differentiate into chondrocytes and adipocytes. Dental pulp from erupted molars displayed a reduced number of cells, contained higher percentage of CD45+ and lower percentage of cells expressing CD90+/CD45-, CD117+/CD45- as compared to unerupted molars. In vitro functional assays demonstrated the ability of a small fraction of cells to differentiate into odontoblasts, osteoblasts, adipocytes and chondrocytes. There was a significant reduction in the osteo-dentinogenic potential of the pulp cells derived from erupted molars compared to unerupted molars. Furthermore, the adipogenic and chondrogenic differentiation of pulp cells from erupted molars was dependent on a long induction period and infrequent. Based on these findings we propose that the dental pulp of the erupted molars contain a small population of multipotent cells, whereas the dental pulp of the unerupted molars does not contain multipotent cells but is enriched in osteo-dentinogenic progenitors engaged in the formation of coronal and radicular odontoblasts. PMID:20193787

  9. Quality evaluation of dissolving pulp fabricated from banana plant stem and its potential for biorefinery.

    Science.gov (United States)

    Das, Atanu Kumar; Nakagawa-Izumi, Akiko; Ohi, Hiroshi

    2016-08-20

    The study was conducted to evaluate the quality of dissolving pulp of Musa sapientum L. (banana) plant stem and its potential for biorefinery. Introduction of pre-hydrolysis prior to any alkaline pulping process helps to reduce the content of hemicellulose and consequently produce acceptably high content of cellulose pulp. Water pre-hydrolysis was done at 150°C for 90min. The amount of lignin, xylan and glucan in the extracted pre-hydrolysis liquor (PHL) was 1.6, 4.9 and 1.6%, respectively. Pulping of pre-extracted chips was done following soda-AQ, alkaline sulfite and kraft process. The ratio of chip to liquor was 1:7 for both pre-hydrolysis and pulping. The kraft pulping process with 20% active alkali and 25% sulfidity at 150°C for 90min showed the best result. The lowest kappa number was 26.2 with a considerable pulp yield of 32.7%. The pulp was bleached by acidic NaClO2 and the consistency was 10% based on air-dried pulp. The lowest amount of 7% NaClO2 was used for the bleaching sequence of D0ED1ED2. After D0ED1ED2 bleaching, the pulp showed that α-cellulose, brightness and ash were 91.9, 77.9 and 1.6% respectively. The viscosity was 19.9cP. Hence, there is a possibility to use banana plant stem as a raw material for dissolving grade pulp and other bioproducts. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Characterization of neurons from immortalized dental pulp stem cells for the study of neurogenetic disorders

    Directory of Open Access Journals (Sweden)

    Nora Urraca

    2015-11-01

    Full Text Available A major challenge to the study and treatment of neurogenetic syndromes is accessing live neurons for study from affected individuals. Although several sources of stem cells are currently available, acquiring these involve invasive procedures, may be difficult or expensive to generate and are limited in number. Dental pulp stem cells (DPSCs are multipotent stem cells that reside deep the pulp of shed teeth. To investigate the characteristics of DPSCs that make them a valuable resource for translational research, we performed a set of viability, senescence, immortalization and gene expression studies on control DPSC and derived neurons. We investigated the basic transport conditions and maximum passage number for primary DPSCs. We immortalized control DPSCs using human telomerase reverse transcriptase (hTERT and evaluated neuronal differentiation potential and global gene expression changes by RNA-seq. We show that neurons from immortalized DPSCs share morphological and electrophysiological properties with non-immortalized DPSCs. We also show that differentiation of DPSCs into neurons significantly alters gene expression for 1305 transcripts. Here we show that these changes in gene expression are concurrent with changes in protein levels of the transcriptional repressor REST/NRSF, which is known to be involved in neuronal differentiation. Immortalization significantly altered the expression of 183 genes after neuronal differentiation, 94 of which also changed during differentiation. Our studies indicate that viable DPSCs can be obtained from teeth stored for ≥72 h, these can then be immortalized and still produce functional neurons for in vitro studies, but that constitutive hTERT immortalization is not be the best approach for long term use of patient derived DPSCs for the study of disease.

  11. Characterization of neurons from immortalized dental pulp stem cells for the study of neurogenetic disorders.

    Science.gov (United States)

    Urraca, Nora; Memon, Rawaha; El-Iyachi, Ikbale; Goorha, Sarita; Valdez, Colleen; Tran, Quynh T; Scroggs, Reese; Miranda-Carboni, Gustavo A; Donaldson, Martin; Bridges, Dave; Reiter, Lawrence T

    2015-11-01

    A major challenge to the study and treatment of neurogenetic syndromes is accessing live neurons for study from affected individuals. Although several sources of stem cells are currently available, acquiring these involve invasive procedures, may be difficult or expensive to generate and are limited in number. Dental pulp stem cells (DPSCs) are multipotent stem cells that reside deep the pulp of shed teeth. To investigate the characteristics of DPSCs that make them a valuable resource for translational research, we performed a set of viability, senescence, immortalization and gene expression studies on control DPSC and derived neurons. We investigated the basic transport conditions and maximum passage number for primary DPSCs. We immortalized control DPSCs using human telomerase reverse transcriptase (hTERT) and evaluated neuronal differentiation potential and global gene expression changes by RNA-seq. We show that neurons from immortalized DPSCs share morphological and electrophysiological properties with non-immortalized DPSCs. We also show that differentiation of DPSCs into neurons significantly alters gene expression for 1305 transcripts. Here we show that these changes in gene expression are concurrent with changes in protein levels of the transcriptional repressor REST/NRSF, which is known to be involved in neuronal differentiation. Immortalization significantly altered the expression of 183 genes after neuronal differentiation, 94 of which also changed during differentiation. Our studies indicate that viable DPSCs can be obtained from teeth stored for ≥72 h, these can then be immortalized and still produce functional neurons for in vitro studies, but that constitutive hTERT immortalization is not be the best approach for long term use of patient derived DPSCs for the study of disease. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

  12. Differentiation potential of STRO-1+ dental pulp stem cells changes during cell passaging

    Directory of Open Access Journals (Sweden)

    Wang Ruoning

    2010-05-01

    Full Text Available Abstract Background Dental pulp stem cells (DPSCs can be driven into odontoblast, osteoblast, and chondrocyte lineages in different inductive media. However, the differentiation potential of naive DPSCs after serial passaging in the routine culture system has not been fully elucidated. Results DPSCs were isolated from human/rat dental pulps by the magnetic activated cell sorting based on STRO-1 expression, cultured and passaged in the conventional culture media. The biological features of STRO-1+ DPSCs at the 1st and 9th passages were investigated. During the long-term passage, the proliferation ability of human STRO-1+ DPSCs was downregulated as indicated by the growth kinetics. When compared with STRO-1+ DPSCs at the 1st passage (DPSC-P1, the expression of mature osteoblast-specific genes/proteins (alkaline phosphatase, bone sialoprotein, osterix, and osteopontin, odontoblast-specific gene/protein (dentin sialophosphoprotein and dentin sialoprotein, and chondrocyte-specific gene/protein (type II collagen was significantly upregulated in human STRO-1+ DPSCs at the 9th passage (DPSC-P9. Furthermore, human DPSC-P9 cells in the mineralization-inducing media presented higher levels of alkaline phosphatase at day 3 and day 7 respectively, and produced more mineralized matrix than DPSC-P9 cells at day 14. In vivo transplantation results showed that rat DPSC-P1 cell pellets developed into dentin, bone and cartilage structures respectively, while DPSC-P9 cells can only generate bone tissues. Conclusions These findings suggest that STRO-1+ DPSCs consist of several interrelated subpopulations which can spontaneously differentiate into odontoblasts, osteoblasts, and chondrocytes. The differentiation capacity of these DPSCs changes during cell passaging, and DPSCs at the 9th passage restrict their differentiation potential to the osteoblast lineage in vivo.

  13. Kinetic study of mesophilic anaerobic digestion of pulp and paper sludge

    International Nuclear Information System (INIS)

    Lin, Yunqin; Wang, Dehan; Li, Qing; Huang, Lijian

    2011-01-01

    Anaerobic digestion of pulp and paper sludge (PPS) and monosodium glutamate waste liquor (MGWL) was studied in completely stirred tank reactors (CSTR) at 37 ± 2 °C. This work focused on the effect of increased organic loading rate (OLR) on the methane production in long-term experiments. For OLR in the range of (1.5–5.0) kg m −3 d −1 based on VS fed, VFA and SCOD concentrations decreased for the first 10 days and then kept stable at about 2.3 kg m −3 and 4.0 kg m −3 respectively until to the critical OLR of 5.0 kg m −3 d −1 ; and the methane generation rate enhanced to 0.838 m 3 m −3 d −1 during this period until to the reactor failure. Additionally, reaction rate constant k and sludge retention time (SRT) are described on the basis of a mass balance in a CSTR followed a first order kinetic equation. In the present study, values for y m and k were obtained as 0.733 m 3 kg −1 of removed VS and 0.07 d −1 , respectively. The simple model can apply for dimensioning a CSTR digesting of organic wastes from pulp and paper industries, food processing industries, sewage treatment plants or biogas crops. -- Highlights: ► Evaluating methane yields for semi-continuous anaerobic co-digestion of PPS and MGWL. ► Determining the critical OLR for semi-continuous co-digestion. ► Developing the kinetic model for co-digestion of PPFS and MGWL in CSTR. ► Dimensioning CSTR by the model equations for organic wastes digestion.

  14. Pulp polyp - A periapical lesion: Radiographic observational study

    Directory of Open Access Journals (Sweden)

    Kandagal V Suresh

    2015-01-01

    Full Text Available Introduction: Pulp polyp (PP is a chronic hyperplastic condition resulting in formation of granulation tissue and proliferative mass. The radiographic appearance of PP has innumerable presentations. Diagnosing and treatment planning of periapical lesions, heavily relies on the radiographic changes surrounding the root structures. Objective: To evaluate different radiographic periapical changes in clinically detected PP patients. Materials and Methods: Patients reporting to Department of Oral Medicine and Radiology and who were clinically diagnosed with PP by an oral diagnostician were subjected to radiographic examination. Digital intraoral periapical radiographs of 50 patients with PP were taken. Various periapical changes in the digital radiographs were recorded by a skilled oral radiologist. The data obtained was subjected to statistical analysis using SPSS ver 17.0 and P-value was set at <0.05 as significant. Result: Periapical changes like periodontal space widening (PDLW, loss of lamina dura, periapical abscess, periapical granuloma, hypercementosis, condensing osteitis and root resorption were noted. Periodontal space widening was seen in all patients (100%, loss of lamina dura was noted in 72%, periapical rarefying osteitis in 56%, condensing osteitis in 8%, hypercementosis, periapical granuloma, and root resorption were seen in 4% of PP patients. Majority of PP were asymptomatic (66%. Pulp polyp was commonly seen in mandibular first molar followed by mandibular second molar and maxillary first molar. Statistically significant difference was noticed between periapical changes in PP patients (P value <0.0001. All PP patients showed definite periapical changes suggesting it to be a periapical lesion. Conclusion: Pulp polyp is confined to the pulpal portion of the tooth which, may or may not cause changes in periapical region. The results of the present study showed that majority of the PP patients were associated with definite periapical

  15. Expression profiling and gene ontology analysis in fathead minnow (Pimephales promelas) liver following exposure to pulp and paper mill effluents

    Energy Technology Data Exchange (ETDEWEB)

    Costigan, Shannon L.; Werner, Julieta; Ouellet, Jacob D.; Hill, Lauren G. [Department of Biology, Lakehead University, 955 Oliver Road, Ontario P7B 5E1, (Canada); Law, R. David, E-mail: dlaw@lakeheadu.ca [Department of Biology, Lakehead University, 955 Oliver Road, Ontario P7B 5E1, (Canada)

    2012-10-15

    Many studies link pulp and paper mill effluent (PPME) exposure to adverse effects in fish populations present in the mill receiving environments. These impacts are often characteristic of endocrine disruption and may include impaired reproduction, development and survival. While these physiological endpoints are well-characterized, the molecular mechanisms causing them are not yet understood. To investigate changes in gene transcription induced by exposure to a PPME at several stages of treatment, male and female fathead minnows (FHMs) were exposed for 6 days to 25% (v/v) secondary (biologically) treated kraft effluent (TK) or 100% (v/v) combined mill outfall (CMO) from a mill producing both kraft pulp and newsprint. The gene expression changes in the livers of these fish were analyzed using a 22 K oligonucleotide microarray. Exposure to TK or CMO resulted in significant changes in the expression levels of 105 and 238 targets in male FHMs and 296 and 133 targets in females, respectively. Targets were then functionally analyzed using gene ontology tools to identify the biological processes in fish hepatocytes that were affected by exposure to PPME after its secondary treatment. Proteolysis was affected in female FHMs exposed to both TK and CMO. In male FHMs, no processes were affected by TK exposure, while sterol, isoprenoid, steroid and cholesterol biosynthesis and electron transport were up-regulated by CMO exposure. The results presented in this study indicate that short-term exposure to PPMEs affects the expression of reproduction-related genes in the livers of both male and female FHMs, and that secondary treatment of PPMEs may not neutralize all of their metabolic effects in fish. Gene ontology analysis of microarray data may enable identification of biological processes altered by toxicant exposure and thus provide an additional tool for monitoring the impact of PPMEs on fish populations.

  16. Expression profiling and gene ontology analysis in fathead minnow (Pimephales promelas) liver following exposure to pulp and paper mill effluents

    International Nuclear Information System (INIS)

    Costigan, Shannon L.; Werner, Julieta; Ouellet, Jacob D.; Hill, Lauren G.; Law, R. David

    2012-01-01

    Many studies link pulp and paper mill effluent (PPME) exposure to adverse effects in fish populations present in the mill receiving environments. These impacts are often characteristic of endocrine disruption and may include impaired reproduction, development and survival. While these physiological endpoints are well-characterized, the molecular mechanisms causing them are not yet understood. To investigate changes in gene transcription induced by exposure to a PPME at several stages of treatment, male and female fathead minnows (FHMs) were exposed for 6 days to 25% (v/v) secondary (biologically) treated kraft effluent (TK) or 100% (v/v) combined mill outfall (CMO) from a mill producing both kraft pulp and newsprint. The gene expression changes in the livers of these fish were analyzed using a 22 K oligonucleotide microarray. Exposure to TK or CMO resulted in significant changes in the expression levels of 105 and 238 targets in male FHMs and 296 and 133 targets in females, respectively. Targets were then functionally analyzed using gene ontology tools to identify the biological processes in fish hepatocytes that were affected by exposure to PPME after its secondary treatment. Proteolysis was affected in female FHMs exposed to both TK and CMO. In male FHMs, no processes were affected by TK exposure, while sterol, isoprenoid, steroid and cholesterol biosynthesis and electron transport were up-regulated by CMO exposure. The results presented in this study indicate that short-term exposure to PPMEs affects the expression of reproduction-related genes in the livers of both male and female FHMs, and that secondary treatment of PPMEs may not neutralize all of their metabolic effects in fish. Gene ontology analysis of microarray data may enable identification of biological processes altered by toxicant exposure and thus provide an additional tool for monitoring the impact of PPMEs on fish populations.

  17. The exposed breast

    International Nuclear Information System (INIS)

    Ingman, Wendy

    2014-01-01

    The skin and lungs are two tissues that are frequently bombarded with cancer-initiating factors, such as ultraviolet rays from the sun and smoke and pollutants in the air we breathe. Yet breast cancer is the most common type of cancer in Australian women, affecting one in eight before the age of 85. It is more common than skin melanoma and lung cancer. Why, then, does the breast so commonly get cancer when it is not a tissue that is particularly exposed to the environmental agents that increase cancer risk in other major organs? Is there something unique about this tissue that makes it particularly susceptible? The breast undergoes cellular changes over the course of the monthly menstrual cycle, and and these changes affect cancer susceptibility. Rising levels of the hormones oestrogen and progesterone occur immediately after the egg is released from the ovary, and these hormones cause the breast cells to divide and change to accommodate further development if pregnancy occurs. If the woman becomes pregnant, the cells in the breast continue to develop and become the milk-producing structures required to feed a newborn baby. But if pregnancy does not occur there is a drop in progesterone, which triggers the death of the newly developed breast cells. This occurs at the same time women have their period. Then the cycle starts again, and continues every month until menopause, unless the woman becomes pregnant.

  18. Exposing the faults

    International Nuclear Information System (INIS)

    Richardson, P.J.

    1989-01-01

    UK NIREX, the body with responsibility for finding an acceptable strategy for deposition of radioactive waste has given the impression throughout its recent public consultation that the problem of nuclear waste is one of public and political acceptability, rather than one of a technical nature. However the results of the consultation process show that it has no mandate from the British public to develop a single, national, deep repository for the burial of radioactive waste. There is considerable opposition to this method of managing radioactive waste and suspicion of the claims by NIREX concerning the supposed integrity and safety of this deep burial option. This report gives substance to those suspicions and details the significant areas of uncertainty in the concept of effective geological containment of hazardous radioactive elements, which remain dangerous for tens of thousands of years. Because the science of geology is essentially retrospective rather than predictive, NIREX's plans for a single, national, deep 'repository' depend heavily upon a wide range of assumptions about the geological and hydrogeological regimes in certain areas of the UK. This report demonstrates that these assumptions are based on a limited understanding of UK geology and on unvalidated and simplistic theoretical models of geological processes, the performance of which can never be directly tested over the long time-scales involved. NIREX's proposals offer no guarantees for the safe and effective containment of radioactivity. They are deeply flawed. This report exposes the faults. (author)

  19. Transplantation of human dental pulp-derived stem cells protects against heatstroke in mice.

    Science.gov (United States)

    Tseng, Ling-Shu; Chen, Sheng-Hsien; Lin, Mao-Tsun; Lin, Ying-Chu

    2015-01-01

    Stem cells from human exfoliated deciduous tooth pulp (SHED) is a promising approach for the treatment of stroke and spinal cord injury. In this study, we investigated the therapeutic effects of SHED for the treatment of multiple organ (including brain, particularly hypothalamus) injury in heatstroke mice. ICR male mice were exposed to whole body heating (WBH; 41.2°C, relative humidity 50-55%, for 1 h) and then returned to normal room temperature (26°C). We observed that intravenous administration of SHED immediately post-WBH exhibited the following therapeutic benefits for recovery after heatstroke: (a) inhibition of WBH-induced neurologic and thermoregulatory deficits; (b) reduction of WBH-induced ischemia, hypoxia, and oxidative damage to the brain (particularly the hypothalamus); (c) attenuation of WBH-induced increased plasma levels of systemic inflammatory response molecules, such as tumor necrosis factor-α and intercellular adhesion molecule-1; (d) improvement of WBH-induced hypothalamo-pituitary-adrenocortical (HPA) axis activity (as reflected by enhanced plasma levels of both adrenocorticotrophic hormone and corticosterone); and (e) attenuation of WBH-induced multiple organ apoptosis as well as lethality. In conclusion, post-WBH treatment with SHED reduced induction of proinflammatory cytokines and oxidative radicals, enhanced plasma induction of both adrenocorticotrophic hormone and corticosterone, and improved lethality in mouse heatstroke. The protective effect of SHED may be related to a decreased inflammatory response, decreased oxidative stress, and an increased HPA axis activity following the WBH injury.

  20. Small Molecules Affect Human Dental Pulp Stem Cell Properties Via Multiple Signaling Pathways

    Science.gov (United States)

    Al-Habib, Mey; Yu, Zongdong

    2013-01-01

    One fundamental issue regarding stem cells for regenerative medicine is the maintenance of stem cell stemness. The purpose of the study was to test whether small molecules can enhance stem cell properties of mesenchymal stem cells (MSCs) derived from human dental pulp (hDPSCs), which have potential for multiple clinical applications. We identified the effects of small molecules (Pluripotin (SC1), 6-bromoindirubin-3-oxime and rapamycin) on the maintenance of hDPSC properties in vitro and the mechanisms involved in exerting the effects. Primary cultures of hDPSCs were exposed to optimal concentrations of these small molecules. Treated hDPSCs were analyzed for their proliferation, the expression levels of pluripotent and MSC markers, differentiation capacities, and intracellular signaling activations. We found that small molecule treatments decreased cell proliferation and increased the expression of STRO-1, NANOG, OCT4, and SOX2, while diminishing cell differentiation into odonto/osteogenic, adipogenic, and neurogenic lineages in vitro. These effects involved Ras-GAP-, ERK1/2-, and mTOR-signaling pathways, which may preserve the cell self-renewal capacity, while suppressing differentiation. We conclude that small molecules appear to enhance the immature state of hDPSCs in culture, which may be used as a strategy for adult stem cell maintenance and extend their capacity for regenerative applications. PMID:23573877

  1. The direct cytotoxic effects of medicaments used in endodontic regeneration on human dental pulp cells.

    Science.gov (United States)

    Labban, Nawaf; Yassen, Ghaeth H; Windsor, L Jack; Platt, Jeffrey A

    2014-12-01

    The purpose of this in vitro study was to evaluate the effects of intracanal medicaments commonly used in endodontic regeneration on the survival of human dental pulp cells (DPCs). DPCs were cultured and exposed to either no medicament treatment or low concentrations (0.3-5 mg ml(-1) ) of calcium hydroxide [Ca(OH)2 ], triple antibiotic paste (TAP), or double antibiotic paste (DAP) for 3 days. After that, toxicity to the DPCs was determined by lactate dehydrogenase activity assays (LDH) and cell proliferation was measured by colorimetric assays (WST-1). Two-way anova followed by Fisher's protected least significant differences was used for statistical analyses (α = 0.05). The group-by-concentration interactions were significant for the LDH and WST-1 assays (P medicaments tested in this study were not cytotoxic in cultured cells. However, these concentrations are much lower than the concentrations that have been advocated in endodontic regeneration. Furthermore, the negative effects of TAP on DPCs were detected at lower concentrations by using the WST-1 assays than by measuring the LDH release. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  2. Fermentation and chemical treatment of pulp and paper mill sludge

    Science.gov (United States)

    Lee, Yoon Y; Wang, Wei; Kang, Li

    2014-12-02

    A method of chemically treating partially de-ashed pulp and/or paper mill sludge to obtain products of value comprising taking a sample of primary sludge from a Kraft paper mill process, partially de-ashing the primary sludge by physical means, and further treating the primary sludge to obtain the products of value, including further treating the resulting sludge and using the resulting sludge as a substrate to produce cellulase in an efficient manner using the resulting sludge as the only carbon source and mixtures of inorganic salts as the primary nitrogen source, and including further treating the resulting sludge and using the resulting sludge to produce ethanol.

  3. Recovering gold from thiosulfate leach pulps via ion exchange

    Science.gov (United States)

    Nicol, Michael J.; O'Malley, Glen

    2002-10-01

    Increasing environmental and occupational safety concerns about the use of cyanide in gold processing has increased interest in more acceptable alternative lixiviants, the most promising of which is thiosulfate. However, the thiosulfate process lacks a proven inpulp method of recovering the dissolved gold because activated carbon is not effective for the absorption of the gold-thiosulfate complex. This paper describes work aimed at evaluating the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors and pulps.

  4. Cogeneration handbook for the pulp and paper industry. [Contains glossary

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, E.A.; Moore, N.L.; Fassbender, L.L.; Garrett-Price, B.A.; Fassbender, A.G.; Eakin, D.E.; Gorges, H.A.

    1984-03-01

    The decision of whether to cogenerate involves several considerations, including technical, economic, environmental, legal, and regulatory issues. Each of these issues is addressed separately in this handbook. In addition, a chapter is included on preparing a three-phase work statement, which is needed to guide the design of a cogeneration system. In addition, an annotated bibliography and a glossary of terminology are provided. Appendix A provides an energy-use profile of the pulp and paper industry. Appendices B and O provide specific information that will be called out in subsequent chapters.

  5. A New Technology for Treating Pulp Waste with Plasma

    International Nuclear Information System (INIS)

    Feng Xiaozhen; Tian Zhongyu

    2009-01-01

    New methods for both the treatment of pulp waste liquor called black liquor (BL) and the recovery of chemicals by using plasma, and the concentration of BL with the freezing technique were developed. The new methods aiming at the pilot plant scale are described and the experiments in a small-scale research facility for demonstration and test are presented. The energy consumption for treating waste liquid is 1 kg/kWh. Plasma processing can reduce the costs for treatment and eliminate pollution. (plasma technology)

  6. Optimal energy management in pulp and paper mills

    International Nuclear Information System (INIS)

    Sarimveis, H.K.; Angelou, A.S.; Retsina, T.R.; Rutherford, S.R.; Bafas, G.V.

    2003-01-01

    In this paper, we examine the utilization of mathematical programming tools for optimum energy management of the power plant in pulp and paper mills. The objective is the fulfillment of the total plant requirements in energy and steam with the minimum possible cost. The proposed methodology is based on the development of a detailed model of the power plant using mass and energy balances and a mathematical formulation of the electrical purchase contract, which can be translated into a rigorous mixed integer linear programming optimization problem. The results show that the method can be a very useful tool for the reduction of production cost due to minimization of the fuel and electricity costs

  7. Inter-laboratory comparisons of hexenuronic acid measurements in kraft eucalyptus pulps using a UV-Vis spectroscopic method

    Science.gov (United States)

    J.Y. Zhu; H.F Zhou; Chai X.S.; Donna Johannes; Richard Pope; Cristina Valls; M. Blanca Roncero

    2014-01-01

    An inter-laboratory comparison of a UV-Vis spectroscopic method (TAPPI T 282 om-13 “Hexeneuronic acid content of chemical pulp”) for hexeneuronic acid measurements was conducted using three eucalyptus kraft pulps. The pulp samples were produced in a laboratory at kappa numbers of approximately 14, 20, and 35. The hexeneuronic acid contents of the three pulps were...

  8. Evolution of Lignocellulosic Macrocomponents in the Wastewater Streams of a Sulfite Pulp Mill: A Preliminary Biorefining Approach

    Directory of Open Access Journals (Sweden)

    Tamara Llano

    2015-01-01

    Full Text Available The evolution of lignin, five- and six-carbon sugars, and other decomposition products derived from hemicelluloses and cellulose was monitored in a sulfite pulp mill. The wastewater streams were characterized and the mass balances throughout digestion and total chlorine free bleaching stages were determined. Summative analysis in conjunction with pulp parameters highlights some process guidelines and valorization alternatives towards the transformation of the traditional factory into a lignocellulosic biorefinery. The results showed a good separation of cellulose (99.64% during wood digestion, with 87.23% of hemicellulose and 98.47% lignin dissolved into the waste streams. The following steps should be carried out to increase the sugar content into the waste streams: (i optimization of the digestion conditions increasing hemicellulose depolymerization; (ii improvement of the ozonation and peroxide bleaching stages, avoiding deconstruction of the cellulose chains but maintaining impurity removal; (iii fractionation of the waste water streams, separating sugars from the rest of toxic inhibitors for 2nd generation biofuel production. A total of 0.173 L of second-generation ethanol can be obtained in the spent liquor per gram of dry wood. The proposed methodology can be usefully incorporated into other related industrial sectors.

  9. Stimulation of angiogenesis, neurogenesis and regeneration by side population cells from dental pulp.

    Science.gov (United States)

    Ishizaka, Ryo; Hayashi, Yuki; Iohara, Koichiro; Sugiyama, Masahiko; Murakami, Masashi; Yamamoto, Tsubasa; Fukuta, Osamu; Nakashima, Misako

    2013-03-01

    Mesenchymal stem cells (MSCs) have been used for cell therapy in various experimental disease models. However, the regenerative potential of MSCs from different tissue sources and the influence of the tissue niche have not been investigated. In this study, we compared the regenerative potential of dental pulp, bone marrow and adipose tissue-derived CD31(-) side population (SP) cells isolated from an individual porcine source. Pulp CD31(-) SP cells expressed the highest levels of angiogenic/neurotrophic factors and had the highest migration activity. Conditioned medium from pulp CD31(-) SP cells produced potent anti-apoptotic activity and neurite outgrowth, compared to those from bone marrow and adipose CD31(-) SP cells. Transplantation of pulp CD31(-) SP cells in a mouse hindlimb ischemia model produced higher blood flow and capillary density than transplantation of bone marrow and adipose CD31(-) SP cells. Motor function recovery and infarct size reduction were greater with pulp CD31(-) SP cells. Pulp CD31(-) SP cells induced maximal angiogenesis, neurogenesis and pulp regeneration in ectopic transplantation models compared to other tissue sources. These results demonstrate that pulp stem cells have higher angiogenic, neurogenic and regenerative potential and may therefore be superior to bone marrow and adipose stem cells for cell therapy. Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Maximal release of highly bifidogenic soluble dietary fibers from industrial potato pulp by minimal enzymatic treatment

    DEFF Research Database (Denmark)

    Thomassen, Lise Vestergaard; Vigsnæs, Louise Kristine; Licht, Tine Rask

    2011-01-01

    Potato pulp is a poorly utilized, high-volume co-processing product resulting from industrial potato starch manufacturing. Potato pulp mainly consists of the tuber plant cell wall material and is particularly rich in pectin, notably galactan branched rhamnogalacturonan I type pectin which has...

  11. Quality evaluation of frozen guava and yellow passion fruit pulps by NIR spectroscopy and chemometrics.

    Science.gov (United States)

    Alamar, Priscila D; Caramês, Elem T S; Poppi, Ronei J; Pallone, Juliana A L

    2016-07-01

    The present study investigated the application of near infrared spectroscopy as a green, quick, and efficient alternative to analytical methods currently used to evaluate the quality (moisture, total sugars, acidity, soluble solids, pH and ascorbic acid) of frozen guava and passion fruit pulps. Fifty samples were analyzed by near infrared spectroscopy (NIR) and reference methods. Partial least square regression (PLSR) was used to develop calibration models to relate the NIR spectra and the reference values. Reference methods indicated adulteration by water addition in 58% of guava pulp samples and 44% of yellow passion fruit pulp samples. The PLS models produced lower values of root mean squares error of calibration (RMSEC), root mean squares error of prediction (RMSEP), and coefficient of determination above 0.7. Moisture and total sugars presented the best calibration models (RMSEP of 0.240 and 0.269, respectively, for guava pulp; RMSEP of 0.401 and 0.413, respectively, for passion fruit pulp) which enables the application of these models to determine adulteration in guava and yellow passion fruit pulp by water or sugar addition. The models constructed for calibration of quality parameters of frozen fruit pulps in this study indicate that NIR spectroscopy coupled with the multivariate calibration technique could be applied to determine the quality of guava and yellow passion fruit pulp. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Effect of Baobab ( Adansonia digitata L.) Fruit Pulp Drink on Iron ...

    African Journals Online (AJOL)

    Objective: To determine the effect of consuming baobab fruit pulp drink with the diet on iron status of school children. Materials and Methods: Baobab fruit pulp was scrapped from the seeds and mixed with water in the ratio of 1:2 (w/v) to produce a refreshing drink. One hundred and forty two school children 6-8 yrs involved ...

  13. Changes in the composition of the pulp, alpha-amylase activity and ...

    African Journals Online (AJOL)

    The laboratory rotting of Egusi Fruits was completed in 120 hours. At this stage pulp became soft and the seeds were extracted easily with the fingers. The changes in the composition of the pulp, alpha-amylase activity and titratable acidity during the controlled rotting of egusi fruit (Colocynthis citrullus L.) for the harvesting of ...

  14. Evaluation of African black pear pulp and oil as ingredients in bread ...

    African Journals Online (AJOL)

    Bakery fat is important ingrredient that affects the rheological properties of bread crumb. In this work, African black peer pulp and pulp oil were used as substitutions to commercial bakery fat 0%, 25%,50%,75% and 100% levels of substitution. The results obtained show that significant difference (p>0.05) occur between the ...

  15. Hydrogen production from carrot pulp by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana

    Energy Technology Data Exchange (ETDEWEB)

    Vrije, Truus de; Budde, Miriam A.W.; Lips, Steef J.; Bakker, Robert R.; Mars, Astrid E.; Claassen, Pieternel A.M. [Wageningen UR, Food and Biobased Research, P.O. Box 17, 6700 AA Wageningen (Netherlands)

    2010-12-15

    Hydrogen was produced from carrot pulp hydrolysate, untreated carrot pulp and (mixtures of) glucose and fructose by the extreme thermophiles Caldicellulosiruptor saccharolyticus and Thermotoga neapolitana in pH-controlled bioreactors. Carrot pulp hydrolysate was obtained after enzymatic hydrolysis of the polysaccharide fraction in carrot pulp. The main sugars in the hydrolysate were glucose, fructose, and sucrose. In fermentations with glucose hydrogen yields and productivities were similar for both strains. With fructose the hydrogen yield of C. saccharolyticus was reduced which might be related to uptake of glucose and fructose by different types of transport systems. With T. neapolitana the fructose consumption rate and consequently the hydrogen productivity were low. The hydrogen yields of both thermophiles were 2.7-2.8 mol H{sub 2}/mol hexose with 10 g/L sugars from carrot pulp hydrolysate. With 20 g/L sugars the yield of T. neapolitana was 2.4 mol H{sub 2}/mol hexose while the yield of C. saccharolyticus was reduced to 1.3 mol H{sub 2}/mol hexose due to high lactate production in the stationary growth phase. C. saccharolyticus was able to grow on carrot pulp and utilized soluble sugars and, after adaptation, pectin and some (hemi)cellulose. No growth was observed with T. neapolitana when using carrot pulp in agitated fermentations. Enzymatic hydrolysis of the polysaccharide fraction prior to fermentation increased the hydrogen yield with almost 10% to 2.3 g/kg of hydrolyzed carrot pulp. (author)

  16. A LARCH BIOREFINERY: INFLUENCE OF WASHING AND PS CHARGE ON PRE-EXTRACTION PSAQ PULPING

    Directory of Open Access Journals (Sweden)

    Hanna S. Hörhammer

    2012-06-01

    Full Text Available This study deals with a biorefinery concept based on larch wood. Wood chips of Siberian larch (Larix sibirica Lebed. were treated with water before pulping at the optimal pre-extraction (PE condition of 150 °C and 90 minutes. Through PE, about 12.4% of the wood mass is dissolved, mainly from the arabinogalactan hemicellulose component. Fermentation of the hemicellulose-rich larch extract with Bacillus coagulans resulted in consumption of all C6 and C5 sugars and produced lactic acid in high yield. PE before pulping resulted in lower (4 to 5% pulp yield than for control kraft pulps. However, the pulp yield loss may be reduced by addition of polysulfide (PS and anthraquinone (AQ. The present study focuses on the effect of the degree of washing of the extracted chips and that of the PS charge in PSAQ pulping on the final properties of the pulp. Three different levels of washing and three different PS charges were tested. The characteristics of the extract, wash water, pulp, and black liquor samples were determined. The amount of sugars in the combined stream of collected extract and wash water obtained by mild washing was 10.2% on o.d. wood.

  17. Characterisation of Arabica Coffee Pulp - Hay from Kintamani - Bali as Prospective Biogas Feedstocks

    Directory of Open Access Journals (Sweden)

    Hendroko Setyobudi Roy

    2018-01-01

    Full Text Available The huge amount of coffee pulp waste is an environmental problem. Anaerobic fermentation is one of the alternative solutions. However, availability of coffee pulp does not appear for year-round, whereas biogas needs continuous feedstocks for digester stability. This research uses coffee pulp from Arabica Coffee Factory at Mengani, Kintamani, Bali–Indonesia. The coffee pulp was transformed into coffee pulp-hay product by sun drying for preservations to extend the raw materials through the year. Characterization of coffee pulp-hay was conducted after to keep for 15 mo for review the prospect as biogas feedstocks. Several parameters were analyzed such as C/N ratio, volatile solids, carbohydrate, protein, fat, lignocellulose content, macro-micro nutrients, and density. The review results indicated that coffee pulp-hay is prospective raw material for biogas feedstock. This well-proven preservation technology was able to fulfill the continuous supply. Furthermore, some problems were found in the recent preliminary experiment related to the density and fungi growth in the conventional laboratory digester. Further investigation was needed to implement the coffee pulp – hay as biogas feedstocks.

  18. Effects of Lactobacillus plantarum and hydrolytic enzymes on fermentation and ruminal degradability of orange pulp silage

    DEFF Research Database (Denmark)

    Taghizadeh, Akbar; Paya, Hamid; Lashkari, Saman

    2015-01-01

    The current study was carried out to examine the effect of inoculants, enzymes and mixtures of them on the fermentation, degradability and nutrient value of orange pulp silage. Orange pulp was treated with water (control), inoculant (Lactobacillus plantarum), enzymes (multiple enzyme) or inoculants...

  19. Fiber length and pulping characteristics of switchgrass, alfalfa stems, hybrid poplar and willow biomasses.

    Science.gov (United States)

    Ai, Jun; Tschirner, Ulrike

    2010-01-01

    Switchgrass (Panicum virgatum), alfalfa stems (Medicago sativa), second year growth hybrid poplar (Populus) and willow (Salix spp.) were examined to determine fiber characteristics, pulping behavior and paper properties. Alfalfa stems and switchgrass both showed length weighted average fiber length (LWW) of 0.78 mm, a very narrow fiber length distribution and high fines content. Willow and hybrid poplar have lower fines content but a very low average fiber length (0.42 and 0.48 mm LWW). In addition, the four biomass species showed distinctly different chemical compositions. Switchgrass was defibered successfully using Soda and Soda Anthraquinone (AQ) pulping and demonstrated good paper properties. Both fast-growing wood species pulped well using the Kraft process, and showed acceptable tensile strength, but low tear strength. Alfalfa stems reacted very poorly to Soda and Soda AQ pulping but responded well to Kraft and Kraft AQ. Pulps with tensile and tear strength considerably higher than those found for commercial aspen pulps were observed for alfalfa. All four biomass species examined demonstrated low pulp yield. The highest yields were obtained with poplar and switchgrass (around 43%). Considering the short fibers and low yields, all four biomass types will likely only be used in paper manufacturing if they offer considerable economic advantage over traditional pulp wood.

  20. An environmental systems analysis of the Kraft pulp industry in Thailand

    NARCIS (Netherlands)

    Warit, J.

    2006-01-01

    The pulp industry inThailandis of economic and social importance because of its production value, the revenues from export and the employment in this sector. The eucalyptus-based Kraft pulp industry plays an

  1. The lycopene content in pulp ad peel of five fresh tomato varieties

    NARCIS (Netherlands)

    Markovic, K.; Panjkota-Krbavcic, I.; Krpan, M.; Bicanic, D.D.; Vahcic, N.

    2010-01-01

    The lycopene content in pulp and peel of five fresh tomato cultivars, most common on Croatian market, was determined by spectrophotometry and the high-performance liquid chromatography (HPLC). Peels from the raw tomatoes contained more lycopene (expressed on a fresh basis) than the pulps: the ratio

  2. Improvement of Pulping Uniformity by Measurement of Single Fiber Kappa Number

    Energy Technology Data Exchange (ETDEWEB)

    Richard R. Gustafson; James B. Callis

    2001-11-20

    A method to measure the kappa of single fibers by staining with a fluorescent dye, Acridine Orange (AO), has been developed. This method is now applied to develop and automated flow-through instrument that permits routine kappa analysis on thousands of images of AO stained fibers to give the fiber kappa number distribution of a pulp sample in a few minutes. The design and operation of the instrument are similar to that of a flow cytometer but with the addition of extensive fiber imaging capability. Fluorescence measurements in the flow-through instrument are found to be consistent with those made with fluorescence microscope provided the signal processing in the flow-thou instrument is handled propertly. The kappa distributions of pulps that were analyzed by means of a density gradient column are compared to those measured with the flow-through instrument with good results. The kappa distributions of various laboratory pulps and commercial pulps have been measured. It has been found that all pulps are non-uniform but that ommercial pulps generally have broader kappa distributions thatn their laboratory counterparts. The effects of different pulping methods and chip pretreatments on pulp uniformity are discussed in the report. Finally, the application of flow-through fluorescence technology to other single fiber measurements are presented.

  3. Fabrication of microfibrillated cellulose gel from waste pulp sludge via mild maceration combined with mechanical shearing

    Science.gov (United States)

    Nusheng Chen; Junyong Zhu; Zhaohui Tong

    2016-01-01

    This article describes a facile route, which combines mild maceration of waste pulp sludge and a mechanical shearing process, to prepare microfibrillated cellulose (MFC) with a high storage modulus. In the maceration, the mixture of glacial acetic acid and hydrogen peroxide was used to extract cellulose from never-dried waste pulp sludge. Then, two different mechanical...

  4. Microarray evaluation of age-related changes in human dental pulp.

    Science.gov (United States)

    Tranasi, Michelangelo; Sberna, Maria Teresa; Zizzari, Vincenzo; D'Apolito, Giuseppe; Mastrangelo, Filiberto; Salini, Luisa; Stuppia, Liborio; Tetè, Stefano

    2009-09-01

    The dental pulp undergoes age-related changes that could be ascribed to physiological, defensive, or pathological irritant-induced changes. These changes are regulated by pulp cell activity and by a variety of extracellular matrix (ECM) macromolecules, playing important roles in growth regulation, tissue differentiation and organization, formation of calcified tissue, and defense mechanisms and reactions to inflammatory stimuli. The aim of this research was to better understand the genetic changes that underlie the histological modification of the dental pulp in aging. The gene expression profile of the human dental pulp in young and older subjects was compared by RNA microarray analysis that allowed to simultaneously analyze the expression levels of thousands of genes. Data were statistically analyzed by Significance Analysis of Microarrays (SAM) Ingenuity Pathway Analysis (IPA) software. Semiquantitative and real-time reverse-transcriptase polymerase chain reaction analyses were performed to confirm the results. Microarray analysis revealed several differentially expressed genes that were categorized in growth factors, transcription regulators, apoptosis regulators, and genes of the ECM. The comparison analysis showed a high expression level of the biological functions of cell and tissue differentiation, development, and proliferation and of the immune, lymphatic, and hematologic system in young dental pulp, whereas the pathway of apoptosis was highly expressed in older dental pulp. Expression profile analyses of human dental pulp represent a sensible and useful tool for the study of mechanisms involved in differentiation, growth and aging of human dental pulp in physiological and pathological conditions.

  5. Melatonin attenuates inflammation of acute pulpitis subjected to dental pulp injury

    Science.gov (United States)

    Li, Ji-Guo; Lin, Jia-Ji; Wang, Zhao-Ling; Cai, Wen-Ke; Wang, Pei-Na; Jia, Qian; Zhang, An-Sheng; Wu, Gao-Yi; Zhu, Guo-Xiong; Ni, Long-Xing

    2015-01-01

    Acute pulpitis (AP), one of the most common diseases in the endodontics, usually causes severe pain to the patients, which makes the search for therapeutic target of AP essential in clinic. Toll-like receptor 4 (TLR4) signaling is widely involved in the mechanism of pulp inflammation, while melatonin has been reported to have an inhibition for a various kinds of inflammation. We hereby studied whether melatonin can regulate the expression of TLR4/NF-ĸB signaling in the pulp tissue of AP and in human dental pulp cells (HDPCs). Two left dental pulps of the adult rat were drilled open to establish the AP model, and the serum levels of melatonin and pro-inflammatory cytokines, including interleukin 1β (IL-1β), interleukin 18 (IL-18) and tumor necrosis factor α (TNF-α), were assessed at 1, 3 and 5 d post injury. At the same time points, the expression of TLR4 signaling in the pulp was explored by quantitative real-time PCR and immunohistochemistry. The AP rats were administered an abdominal injection of melatonin to assess whether melatonin rescued AP and TLR4/NF-ĸB signaling. Dental pulp injury led to an approximately five-day period acute pulp inflammation and necrosis in the pulp and a significant up-regulation of IL-1β, IL-18 and TNF-α in the serum. ELISA results showed that the level of melatonin in the serum decreased due to AP, while an abdominal injection of melatonin suppressed the increase in serum cytokines and the percentage of necrosis at the 5 d of the injured pulp. Consistent with the inflammation in AP rats, TLR4, NF-ĸB, TNF-α and IL-1β in the pulp were increased post AP compared with the baseline expression. And melatonin showed an inhibition on TLR4/NF-ĸB signaling as well as IL-1β and TNF-α production in the pulp of AP rats. Furthermore, melatonin could also regulate the expression of TLR4/NF-ĸB signaling in LPS-stimulated HDPCs. These data suggested that dental pulp injury induced AP and reduced the serum level of melatonin and that

  6. The economy of chip, tree section and short wood methods in the procurement of a pulp mill; Hake-, puu- ja puutavaralajimenetelmien taloudellisuus massatehtaan kuitu- ja energiapuun hankinnassa

    Energy Technology Data Exchange (ETDEWEB)

    Imponen, V [Metsaeteho Oy, Helsinki (Finland)

    1997-12-01

    Regional forest management plans for Finland`s private, non-industrial forestry indicate that first thinnings account for 13 % of the felling potential in these forests. The majority of first thinnings focus on pine-dominated stands. First-thinnings wood represents 29 % of the allowable cut consisting of pine pulpwood. However, small-diameter pine has not enjoyed great demand as raw material by the chemical pulp industry due to the high associated production costs and due to its inferior fibre properties when compared to large-sized softwood logs. Consequently, research and development work has been focused on the procurement, handling and usage of small-diameter wood, and especially of first-thinning pine. Both defibration and use as fuel are options when considering how to exploit small-diameter softwood raw material. Integrated procurement of industrial wood and wood fuel have improved the profitability of wood from thinnings in pulp manufacture and in energy generation at the mill. These methods would appear to be economic in regard to both the wood procurement of the pulp mills even at the present prices paid for alternative fuels. Advances in combustion technology and increased generation of electric power improve the competitiveness of methods based on the harvesting tree sections in comparison with the shortwood system yielding delimbed roundwood. The adoption of longer timber lorry-trailer combination as recognised by EU directives will have the effect of reducing the transportation costs for non-delimbed and partially delimbed wood. (orig.)

  7. 76 FR 2145 - International Paper Company, Franklin Pulp & Paper Mill, Including On-Site Leased Workers From...

    Science.gov (United States)

    2011-01-12

    ... Company, Franklin Pulp & Paper Mill, Including On-Site Leased Workers From Railserve, Franklin, VA..., applicable to workers and former workers of International Paper Company, Franklin Pulp & Paper Mill, Franklin... follows: All workers International Paper Company, Franklin Pulp & Paper Mill, including on-site leased...

  8. 75 FR 26794 - International Paper Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From...

    Science.gov (United States)

    2010-05-12

    ... Company Franklin Pulp & Paper Mill Including On-Site Leased Workers From Railserve, Franklin, VA; Amended... workers of International Paper Company, Franklin Pulp & Paper Mill, Franklin, Virginia. The notice was... Pulp & Paper Mill. The Department has determined that these workers were sufficiently under the control...

  9. Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface

    Directory of Open Access Journals (Sweden)

    Stefanova Vessela P.

    2015-03-01

    Full Text Available Introduction: Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment.

  10. [Application of Fourier transform attenuated total reflection infrared spectroscopy in analysis of pulp and paper industry].

    Science.gov (United States)

    Zhang, Yong; Cao, Chun-yu; Feng, Wen-ying; Xu, Ming; Su, Zhen-hua; Liu, Xiao-meng; Lü, Wei-jun

    2011-03-01

    As one of the most powerful tools to investigate the compositions of raw materials and the property of pulp and paper, infrared spectroscopy has played an important role in pulp and paper industry. However, the traditional transmission infrared spectroscopy has not met the requirements of the producing processes because of its disadvantages of time consuming and sample destruction. New technique would be needed to be found. Fourier transform attenuated total reflection infrared spectroscopy (ATR-FTIR) is an advanced spectroscopic tool for nondestructive evaluation and could rapidly, accurately estimate the production properties of each process in pulp and paper industry. The present review describes the application of ATR-FTIR in analysis of pulp and paper industry. The analysis processes will include: pulping, papermaking, environmental protecting, special processing and paper identifying.

  11. Can dental pulp calcification predict the risk of ischemic cardiovascular disease?

    Science.gov (United States)

    Khojastepour, Leila; Bronoosh, Pegah; Khosropanah, Shahdad; Rahimi, Elham

    2013-09-01

    To report the association of pulp calcification with that of cardiovascular disease (CVD) using digital panoramic dental radiographs. Digital panoramic radiographs of patients referred from the angiography department were included if the patient was under 55 years old and had non-restored or minimally restored molars and canines. An oral and maxillofacial radiologist evaluated the images for pulpal calcifications in the selected teeth. The sensitivity, specificity, positive predictive value and negative predictive value of panoramic radiography in predicting CVD were calculated. Out of 122 patients who met the criteria, 68.2% of the patients with CVD had pulp chamber calcifications. Pulp calcification in panoramic radiography had a sensitivity of 68.9% to predict CVD. This study demonstrates that patients with CVD show an increased incidence of pulp calcification compared with healthy patients. The findings suggest that pulp calcification on panoramic radiography may have possibilities for use in CVD screening.

  12. Hard tissue deposition in dental pulp canal by {alpha}-tricalcium phosphate cement

    Energy Technology Data Exchange (ETDEWEB)

    Yoshikawa, M.; Toda, T. [Osaka Dental Univ. (Japan). Dept. of Endodontics; Mandai, Y. [Bio-Chemical Lab. of Nitta Gelatin Inc., Yao (Japan); Oonishi, H. [Osaka Minami National Hospital, Kawachi (Japan). Dept. of Orthopaedic Surgery

    2001-07-01

    Canal closure by hard tissue proliferation in the pulp canal and/or apical foramen is the most ideal healing after pulp removal. Generally, Ca(OH){sub 2} may induce secondary dentine or dentine-bridge on the amputated pulp surface. However, Ca(OH){sub 2} shows strong alkalinity and may cause severe inflammatory responses in the residual pulp. Moreover, completely formed dentine-bridge at the orifice will disturb further treatment of residual pulp because of the difficulty in localizing the pathway. The purpose of this study was to see hard tissue induction using newly developed {alpha}-tricalcium phosphate cement and to recognize the morphological difference of hard tissue from that of Ca(OH){sub 2}. (orig.)

  13. Effectiveness of sucrose during the frozen storage of arazá (Eugenia stipitata Mc. Vaugh pulp

    Directory of Open Access Journals (Sweden)

    Kelly Johanna Silva-Bustos

    2011-12-01

    Full Text Available The effects of sucrose on the quality of frozen arazá pulp were investigated. Five levels of sucrose (0, 5, 10, 20, and 30% were evaluated in combination with freezing at low speed, storage during one month, and thawing at two different speeds. Sensory quality and water loss after centrifugation (WLAC were evaluated in the samples. Before freezing sucrose addition (5-30% to the pulp did not affect the sensory quality of the samples, but a negative effect on WLAC at 5-10% sucrose was observed. Furthermore, addition of 20-30% sucrose to arazá pulp, in combination with low speed-freezing, frozen storage, and low-speed-thawing, can be a useful technique to preserve the texture of arazá pulp. The described treatment gave results comparable to those obtained for the fresh pulp and much better than those obtained when freezing was done at high speed

  14. The Fractionation of Loblolly Pine Woodchips Into Pulp For Making Paper Products

    Energy Technology Data Exchange (ETDEWEB)

    Kiran Kadam, PhD

    2006-11-30

    The overall goal of the project was to test the PureVision biomass fractionation technology for making pulp from loblolly pine. A specific goal was to produce a pulp product that is comparable to pulp produced from the kraft process, while reducing the environmental effects of the kraft process, known to be a highly pollutant process. The overall goal of the project was met by using the biomass fractionation concept for making pulp product. This proof-of-concept study, done with Southern pine pinchips as feedstock, evaluated NaOH concentration and residence time as variables in single-stage cocurrent pulping process. It can be concluded that 1% NaOH is adequate for effective delignification using the PureVision process; this is about 1/3 of that used in the kraft process. Also, the PureVision process does not use sulfur-based chemicals such as N2S and hence, is environmentally more benign.

  15. Application of thermophilic enzymes and water jet system to cassava pulp.

    Science.gov (United States)

    Chaikaew, Siriporn; Maeno, Yuka; Visessanguan, Wonnop; Ogura, Kota; Sugino, Gaku; Lee, Seung-Hwan; Ishikawa, Kazuhiko

    2012-12-01

    Co-production of fermentable sugars and nanofibrillated cellulose from cassava pulp was achieved by the combination of thermophilic enzymes (endoglucanase, β-glucosidase, and α-amylase) and a new atomization system (Star Burst System; SBS), which employs opposing water jets. The SBS represents a key technology for providing cellulose nanofibers and improving the enzymatic saccharification of cassava pulp. Depending on the enzymes used, the production of glucose from cassava pulp treated with the SBS was 1.2- to 2.5-fold higher than that from pulp not treated with the SBS. Nanofibrillated cellulose with the gel-like property in suspension was produced (yield was over 90%) by α-amylase treatment, which completely released trapped starch granules from the fibrous cell wall structure of cassava pulp pretreated with the SBS. The SBS provides an environmentally low-impact pretreatment system for processing biomass material into value-added products. Copyright © 2012 Elsevier Ltd. All rights reserved.

  16. Composition, texture and methane potential of cellulosic residues from Lewis acids organosolv pulping of wheat straw.

    Science.gov (United States)

    Constant, Sandra; Barakat, Abdellatif; Robitzer, Mike; Di Renzo, Francesco; Dumas, Claire; Quignard, Françoise

    2016-09-01

    Cellulosic pulps have been successfully isolated from wheat straw through a Lewis acids organosolv treatment. The use of Lewis acids with different hardness produced pulps with different delignification degrees. The cellulosic residue was characterised by chemical composition, X-ray diffraction, FT-IR spectroscopy, N2 physisorption, scanning electron microscopy and potential for anaerobic digestibility. Surface area and pore volume increased with the hardness of the Lewis acid, in correspondence with the decrease of the amount of lignin and hemicellulose in the pulp. The non linearity of the correlation between porosity and composition suggests that an agglomeration of cellulose fibrils occurs in the early stages of pulping. All organosolv pulps presented a significantly higher methane potential than the parent straw. A methane evolution of 295Ncm(3)/g OM was reached by a moderate improvement of the accessibility of the native straw. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Carcass characteristics and meat quality of heavy swine fed different citrus pulp levels

    Directory of Open Access Journals (Sweden)

    P.H. Watanabe

    2010-08-01

    Full Text Available An assay with 36 swine initially weighting 83.7±5.1kg body weight (BW was carried out to evaluate the effects of the use of different dietary citrus pulp levels, 0, 10%, 20%, and 30%, upon digestive organs weights, carcass characteristics, and meat quality of animals subjected to qualitative feed restriction program, and slaughtered at 130kg BW. Linear response (P0.05. Higher levels of citrus pulp neither decreased backfat thickness nor increased amount of lean meat, indicative that qualitative feed restriction was not efficient. Positive linear effect (P<0.05 on pH measured 24 hours after slaughter and negative linear effect (P<0.05 on color characteristics as function of citrus pulp dietary levels were verified. Citrus pulp addition in qualitative feed restriction program may not be effective. As no deleterious effects upon meat qualities were observed, citrus pulp can be used as an alternative feedstuff for finishing swine.

  18. Integration of water footprint accounting and costs for optimal pulp supply mix in paper industry

    DEFF Research Database (Denmark)

    Manzardo, Alessandro; Ren, Jingzheng; Piantella, Antonio

    2014-01-01

    studies have focused on these aspects, but there have been no previous reports on the integrated application of raw material water footprint accounting and costs in the definition of the optimal supply mix of chemical pulps from different countries. The current models that have been applied specifically...... that minimizes the water footprint accounting results and costs of chemical pulp, thereby facilitating the assessment of the water footprint by accounting for different chemical pulps purchased from various suppliers, with a focus on the efficiency of the production process. Water footprint accounting...... was adapted to better represent the efficiency of pulp and paper production. A multi-objective model for supply mix optimization was also developed using multi-criteria decision analysis (MCDA). Water footprint accounting confirmed the importance of the production efficiency of chemical pulp, which affected...

  19. High-alkali low-temperature polysulfide pulping (HALT) of Scots pine.

    Science.gov (United States)

    Paananen, Markus; Sixta, Herbert

    2015-10-01

    High-alkali low-temperature polysulfide pulping (HALT) was effectively utilised to prevent major polysaccharide losses while maintaining the delignification rate. A yield increase of 6.7 wt% on wood was observed for a HALT pulp compared to a conventionally produced kappa number 60 pulp with comparable viscosity. Approximately 70% of the yield increase was attributed to improved galactoglucomannan preservation and 30% to cellulose. A two-stage oxygen delignification sequence with inter-stage peroxymonosulphuric acid treatment was used to ensure delignification to a bleachable grade. In a comparison to conventional pulp, HALT pulp effectively maintained its yield advantage. Diafiltration trials indicate that purified black liquor can be directly recycled, as large lignin fractions and basically all dissolved polysaccharides were separated from the alkali-rich BL. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Materials for the pulp and paper industry. Section 1: Development of materials for black liquor recovery boilers

    Energy Technology Data Exchange (ETDEWEB)

    Keiser, J.R.; Hubbard, C.R.; Payzant, E.A. [Oak Ridge National Lab., TN (United States)] [and others

    1997-04-01

    Black liquor recovery boilers are essential components of kraft pulp and paper mills because they are a critical element of the system used to recover the pulping chemicals required in the kraft pulping process. In addition, the steam produced in these boilers is used to generate a significant portion of the electrical power used in the mill. Recovery boilers require the largest capital investment of any individual component of a paper mill, and these boilers are a major source of material problems in a mill. The walls and floors of these boilers are constructed of tube panels that circulate high pressure water. Molten salts (smelt) accumulate on the floor of recovery boilers, and leakage of water into the boiler can result in a violent explosion when the leaked water instantly vaporizes upon contacting the molten smelt. Because corrosion of the conventionally-used carbon steel tubing was found to be excessive in the lower section of recovery boilers, use of stainless steel/carbon steel co-extruded tubing was adopted for boiler walls to lessen corrosion and reduce the likelihood of smelt/water explosions. Eventually, this co-extruded or composite (as it is known in the industry) tubing was selected for use as a portion or all of the floor of recovery boilers, particularly those operating at pressures > 6.2 MPa (900 psi), because of the corrosion problems encountered in carbon steel floor tubes. Since neither the cause of the cracking nor an effective solution has been identified, this program was established to develop a thorough understanding of the degradation that occurs in the composite tubing used for walls and floors. This is being accomplished through a program that includes collection and review of technical reports, examination of unexposed and cracked tubes from boiler floors, computer modeling to predict residual stresses under operating conditions, and operation of laboratory tests to study corrosion, stress corrosion cracking, and thermal fatigue.