WorldWideScience

Sample records for experimental thermochemical study

  1. Biomass thermochemical gasification: Experimental studies and modeling

    Science.gov (United States)

    Kumar, Ajay

    The overall goals of this research were to study the biomass thermochemical gasification using experimental and modeling techniques, and to evaluate the cost of industrial gas production and combined heat and power generation. This dissertation includes an extensive review of progresses in biomass thermochemical gasification. Product gases from biomass gasification can be converted to biopower, biofuels and chemicals. However, for its viable commercial applications, the study summarizes the technical challenges in the gasification and downstream processing of product gas. Corn stover and dried distillers grains with solubles (DDGS), a non-fermentable byproduct of ethanol production, were used as the biomass feedstocks. One of the objectives was to determine selected physical and chemical properties of corn stover related to thermochemical conversion. The parameters of the reaction kinetics for weight loss were obtained. The next objective was to investigate the effects of temperature, steam to biomass ratio and equivalence ratio on gas composition and efficiencies. DDGS gasification was performed on a lab-scale fluidized-bed gasifier with steam and air as fluidizing and oxidizing agents. Increasing the temperature resulted in increases in hydrogen and methane contents and efficiencies. A model was developed to simulate the performance of a lab-scale gasifier using Aspen Plus(TM) software. Mass balance, energy balance and minimization of Gibbs free energy were applied for the gasification to determine the product gas composition. The final objective was to optimize the process by maximizing the net energy efficiency, and to estimate the cost of industrial gas, and combined heat and power (CHP) at a biomass feedrate of 2000 kg/h. The selling price of gas was estimated to be 11.49/GJ for corn stover, and 13.08/GJ for DDGS. For CHP generation, the electrical and net efficiencies were 37 and 86%, respectively for corn stover, and 34 and 78%, respectively for DDGS. For

  2. Experimental and thermodynamic study of Co-Fe and Mn-Fe based mixed metal oxides for thermochemical energy storage application

    Science.gov (United States)

    André, Laurie; Abanades, Stéphane; Cassayre, Laurent

    2017-06-01

    Metal oxides are potential materials for thermochemical heat storage, and among them, cobalt oxide and manganese oxide are attracting attention. Furthermore, studies on mixed oxides are ongoing, as the synthesis of mixed oxides could be a way to answer the drawbacks of pure metal oxides, such as slow reaction kinetics, loss-in-capacity over cycles or sintering, selected for thermochemical heat storage application. The addition of iron oxide is under investigation and the obtained results are presented. This work proposes a comparison of thermodynamic modelling with experimental data in order to identify the impact of iron oxide addition to cobalt oxide and manganese oxide. Fe addition decreased the redox activity and energy storage capacity of Co3O4, whereas the cycling stability of Mn2O3 was significantly improved with added Fe amounts above 20 mol% while the energy storage capacity was unchanged. The thermodynamic modelling method to predict the behavior of the Mn-Fe-O and Co-Fe-O systems was validated, and the possibility to identify other mixed oxides becomes conceivable, by enabling the selection of transition metals additives for metal oxides destined for thermochemical energy storage applications.

  3. CFD Studies on Biomass Thermochemical Conversion

    Science.gov (United States)

    Wang, Yiqun; Yan, Lifeng

    2008-01-01

    Thermochemical conversion of biomass offers an efficient and economically process to provide gaseous, liquid and solid fuels and prepare chemicals derived from biomass. Computational fluid dynamic (CFD) modeling applications on biomass thermochemical processes help to optimize the design and operation of thermochemical reactors. Recent progression in numerical techniques and computing efficacy has advanced CFD as a widely used approach to provide efficient design solutions in industry. This paper introduces the fundamentals involved in developing a CFD solution. Mathematical equations governing the fluid flow, heat and mass transfer and chemical reactions in thermochemical systems are described and sub-models for individual processes are presented. It provides a review of various applications of CFD in the biomass thermochemical process field. PMID:19325848

  4. CFD Studies on Biomass Thermochemical Conversion

    Directory of Open Access Journals (Sweden)

    Lifeng Yan

    2008-06-01

    Full Text Available Thermochemical conversion of biomass offers an efficient and economically process to provide gaseous, liquid and solid fuels and prepare chemicals derived from biomass. Computational fluid dynamic (CFD modeling applications on biomass thermochemical processes help to optimize the design and operation of thermochemical reactors. Recent progression in numerical techniques and computing efficacy has advanced CFD as a widely used approach to provide efficient design solutions in industry. This paper introduces the fundamentals involved in developing a CFD solution. Mathematical equations governing the fluid flow, heat and mass transfer and chemical reactions in thermochemical systems are described and sub-models for individual processes are presented. It provides a review of various applications of CFD in the biomass thermochemical process field.

  5. Experimental proof of concept of a pilot-scale thermochemical storage unit

    Science.gov (United States)

    Tescari, Stefania; Singh, Abhishek; de Oliveira, Lamark; Breuer, Stefan; Agrafiotis, Christos; Roeb, Martin; Sattler, Christian; Marcher, Johnny; Pagkoura, Chrysa; Karagiannakis, George; Konstandopoulos, Athanasios G.

    2017-06-01

    The present study presents installation and operation of the first pilot scale thermal storage unit based on thermochemical redox-cycles. The reactive core is composed of a honeycomb ceramic substrate, coated with cobalt oxide. This concept, already analyzed and presented at lab-scale, is now implemented at a larger scale: a total of 280 kg of storage material including 90 kg of cobalt oxide. The storage block was implemented inside an existing solar facility and connected to the complete experimental set-up. This experimental set-up is presented, with focus on the measurement system and the possible improvement for a next campaign. Start-up and operation of the system is described during the first complete charge-discharge cycle. The effect of the chemical reaction on the stored capacity is clearly detected by analysis of the temperature distribution data obtained during the experiments. Furthermore two consecutive cycles show no evident loss of reactivity inside the material. The system is cycled between 650°C and 1000°C. In this temperature range, the total energy stored was about 50 kWh, corresponding to an energy density of 630 kJ/kg. In conclusion, the concept feasibility was successfully shown, together with a first calculation on the system performance.

  6. Benzoic acid derivatives: Evaluation of thermochemical properties with complementary experimental and computational methods

    Energy Technology Data Exchange (ETDEWEB)

    Verevkin, Sergey P., E-mail: sergey.verevkin@uni-rostock.de [Department of Physical Chemistry and Department “Science and Technology of Life, Light and Matter”, University of Rostock, D-18059 Rostock (Germany); Department of Physical Chemistry, Kazan Federal University, 420008 Kazan (Russian Federation); Zaitsau, Dzmitry H. [Department of Physical Chemistry, Kazan Federal University, 420008 Kazan (Russian Federation); Emeĺyanenko, Vladimir N. [Department of Physical Chemistry and Department “Science and Technology of Life, Light and Matter”, University of Rostock, D-18059 Rostock (Germany); Stepurko, Elena N. [Chemistry Faculty and Research Institute for Physical Chemical Problems, Belarusian State University, 220030 Minsk (Belarus); Zherikova, Kseniya V. [Nikolaev Institute of Inorganic Chemistry of Siberian Branch of Russian Academy of Sciences, 630090 Novosibirsk (Russian Federation)

    2015-12-20

    Highlights: • Vapor pressures of benzoic acid derivatives were measured. • Sublimation enthalpies were derived and compared with the literature. • Thermochemical data tested for consistency using additivity rules and computations. • Contradiction between available enthalpies of sublimation was resolved. • Pairwise interactions of substituents on the benzene ring were derived. - Abstract: Molar sublimation enthalpies of the methyl- and methoxybenzoic acids were derived from the transpiration method, static method, and TGA. Thermochemical data available in the literature were collected, evaluated, and combined with own experimental results. This collection together with the new experimental results reported here has helped to resolve contradictions in the available enthalpy data and to recommend sets of sublimation and formation enthalpies for the benzoic acid derivatives. Gas-phase enthalpies of formation calculated with the G4 quantum-chemical method were in agreement with the experiment. Pairwise interactions of the methyl, methoxy, and carboxyl substituents on the benzene ring were derived and used for the development of simple group-additivity procedures for estimation of the vaporization enthalpies, gas-phase, and liquid-phase enthalpies of formation of substituted benzenes.

  7. Materials study supporting thermochemical hydrogen cycle sulfuric acid decomposer design

    Science.gov (United States)

    Peck, Michael S.

    Increasing global climate change has been driven by greenhouse gases emissions originating from the combustion of fossil fuels. Clean burning hydrogen has the potential to replace much of the fossil fuels used today reducing the amount of greenhouse gases released into the atmosphere. The sulfur iodine and hybrid sulfur thermochemical cycles coupled with high temperature heat from advanced nuclear reactors have shown promise for economical large-scale hydrogen fuel stock production. Both of these cycles employ a step to decompose sulfuric acid to sulfur dioxide. This decomposition step occurs at high temperatures in the range of 825°C to 926°C dependent on the catalysis used. Successful commercial implementation of these technologies is dependent upon the development of suitable materials for use in the highly corrosive environments created by the decomposition products. Boron treated diamond film was a potential candidate for use in decomposer process equipment based on earlier studies concluding good oxidation resistance at elevated temperatures. However, little information was available relating the interactions of diamond and diamond films with sulfuric acid at temperatures greater than 350°C. A laboratory scale sulfuric acid decomposer simulator was constructed at the Nuclear Science and Engineering Institute at the University of Missouri-Columbia. The simulator was capable of producing the temperatures and corrosive environments that process equipment would be exposed to for industrialization of the sulfur iodide or hybrid sulfur thermochemical cycles. A series of boron treated synthetic diamonds were tested in the simulator to determine corrosion resistances and suitability for use in thermochemical process equipment. These studies were performed at twenty four hour durations at temperatures between 600°C to 926°C. Other materials, including natural diamond, synthetic diamond treated with titanium, silicon carbide, quartz, aluminum nitride, and Inconel

  8. Thermochemical stability of Li-Cu-O ternary compounds stable at room temperature analyzed by experimental and theoretical methods

    Energy Technology Data Exchange (ETDEWEB)

    Lepple, Maren [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Applied Materials - Applied Materials Physics; Technische Univ. Darmstadt (Germany). Eduard-Zintl-Inst. of Inorganic and Physical Chemistry; Rohrer, Jochen; Albe, Karsten [Technische Univ. Darmstadt (Germany). Fachgebiet Materialmodellierung; Adam, Robert; Rafaja, David [Technical Univ. Freiberg (Germany). Inst. of Materials Science; Cupid, Damian M. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Applied Materials - Applied Materials Physics; Austrian Institute of Technology GmbH, Vienna (Austria). Center for Low-Emission Transport TECHbase; Seifert, Hans J. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Applied Materials - Applied Materials Physics

    2017-11-15

    Compounds in the Li-Cu-O system are of technological interest due to their electrochemical properties which make them attractive as electrode materials, i.e., in future lithium ion batteries. In order to select promising compositions for such applications reliable thermochemical data are a prerequisite. Although various groups have investigated individual ternary phases using different experimental setups, up to now, no systematic study of all relevant phases is available in the literature. In this study, we combine drop solution calorimetry with density function theory calculations to systematically investigate the thermodynamic properties of ternary Li-Cu-O phases. In particular, we present a consistently determined set of enthalpies of formation, Gibbs energies and heat capacities for LiCuO, Li{sub 2}CuO{sub 2} and LiCu{sub 2}O{sub 2} and compare our results with existing literature.

  9. An experimental test plan for the characterization of molten salt thermochemical properties in heat transport systems

    Energy Technology Data Exchange (ETDEWEB)

    Pattrick Calderoni

    2010-09-01

    Molten salts are considered within the Very High Temperature Reactor program as heat transfer media because of their intrinsically favorable thermo-physical properties at temperatures starting from 300 C and extending up to 1200 C. In this context two main applications of molten salt are considered, both involving fluoride-based materials: as primary coolants for a heterogeneous fuel reactor core and as secondary heat transport medium to a helium power cycle for electricity generation or other processing plants, such as hydrogen production. The reference design concept here considered is the Advanced High Temperature Reactor (AHTR), which is a large passively safe reactor that uses solid graphite-matrix coated-particle fuel (similar to that used in gas-cooled reactors) and a molten salt primary and secondary coolant with peak temperatures between 700 and 1000 C, depending upon the application. However, the considerations included in this report apply to any high temperature system employing fluoride salts as heat transfer fluid, including intermediate heat exchangers for gas-cooled reactor concepts and homogenous molten salt concepts, and extending also to fast reactors, accelerator-driven systems and fusion energy systems. The purpose of this report is to identify the technical issues related to the thermo-physical and thermo-chemical properties of the molten salts that would require experimental characterization in order to proceed with a credible design of heat transfer systems and their subsequent safety evaluation and licensing. In particular, the report outlines an experimental R&D test plan that would have to be incorporated as part of the design and operation of an engineering scaled facility aimed at validating molten salt heat transfer components, such as Intermediate Heat Exchangers. This report builds on a previous review of thermo-physical properties and thermo-chemical characteristics of candidate molten salt coolants that was generated as part of the

  10. Thermochemical study of the system Fe-As-S

    Science.gov (United States)

    Barton, P.B.

    1969-01-01

    The results of Toulmin and Barton (1964) for the Fe-S system have been combined with a series of new measurements on As-bearing assemblages in the 500??-850??C temperature range to derive data on the free energies, enthalpies, and entropies of formation for arsenopyrite, loellingite, orpiment, realgar, FeAs, and Fe2As. The enthalpies and free energies of formation of orpiment and realgar are only approximately one-half as large as indicated in recent compilations of thermochemical data (Wagman et al., 1965). Data are also presented for the covariation of activity of S2(g) with temperature and composition of the sulfur-arsenic liquid. ?? 1969.

  11. Experimental results of a 3 k Wh thermochemical heat storage module for space heating application

    NARCIS (Netherlands)

    Finck, C.J.; Henquet, E.M.R.; Soest, C.F.L. van; Oversloot, H.P.; Jong, A.J. de; Cuypers, R.; Spijker, J.C. van 't

    2014-01-01

    A 3 kWh thermochemical heat storage (TCS) module was built as part of an all-in house system implementation focusing on space heating application at a temperature level of 40 ºC and a temperature lift of 20 K. It has been tested and measurements showed a maximum water circuit temperature span

  12. Experimental investigation on thermochemical sulfate reduction by H2S initiation

    Science.gov (United States)

    Zhang, T.; Amrani, A.; Ellis, G.S.; Ma, Q.; Tang, Y.

    2008-01-01

    Hydrogen sulfide (H2S) is known to catalyze thermochemical sulfate reduction (TSR) by hydrocarbons (HC), but the reaction mechanism remains unclear. To understand the mechanism of this catalytic reaction, a series of isothermal gold-tube hydrous pyrolysis experiments were conducted at 330 ??C for 24 h under a constant confining pressure of 24.1 MPa. The reactants used were saturated HC (sulfur-free) and CaSO4 in the presence of variable H2S partial pressures at three different pH conditions. The experimental results showed that the in-situ pH of the aqueous solution (herein, in-situ pH refers to the calculated pH of aqueous solution under the experimental conditions) can significantly affect the rate of the TSR reaction. A substantial increase in the TSR reaction rate was recorded with a decrease in the in-situ pH value of the aqueous solution involved. A positive correlation between the rate of TSR and the initial partial pressure of H2S occurred under acidic conditions (at pH ???3-3.5). However, sulfate reduction at pH ???5.0 was undetectable even at high initial H2S concentrations. To investigate whether the reaction of H2S(aq) and HSO4- occurs at pH ???3, an additional series of isothermal hydrous pyrolysis experiments was conducted with CaSO4 and variable H2S partial pressures in the absence of HC at the same experimental temperature and pressure conditions. CaSO4 reduction was not measurable in the absence of paraffin even with high H2S pressure and acidic conditions. These experimental observations indicate that the formation of organosulfur intermediates from H2S reacting with hydrocarbons may play a significant role in sulfate reduction under our experimental conditions rather than the formation of elemental sulfur from H2S reacting with sulfate as has been suggested previously (Toland W. G. (1960) Oxidation of organic compounds with aqueous sulphate. J. Am. Chem. Soc. 82, 1911-1916). Quantification of labile organosulfur compounds (LSC), such as thiols

  13. Study of thermochemical sulfate reduction mechanism using compound specific sulfur isotope analysis

    Science.gov (United States)

    Meshoulam, Alexander; Ellis, Geoffrey S.; Ahmad, Ward Said; Deev, Andrei; Sessions, Alex L.; Tang, Yongchun; Adkins, Jess F.; Liu, Jinzhong; Gilhooly, William P.; Aizenshtat, Zeev; Amrani, Alon

    2016-01-01

    The sulfur isotopic fractionation associated with the formation of organic sulfur compounds (OSCs) during thermochemical sulfate reduction (TSR) was studied using gold-tube pyrolysis experiments to simulate TSR. The reactants used included n-hexadecane (n-C16) as a model organic compound with sulfate, sulfite, or elemental sulfur as the sulfur source. At the end of each experiment, the S-isotopic composition and concentration of remaining sulfate, H2S, benzothiophene, dibenzothiophene, and 2-phenylthiophene (PT) were measured. The observed S-isotopic fractionations between sulfate and BT, DBT, and H2S in experimental simulations of TSR correlate well with a multi-stage model of the overall TSR process. Large kinetic isotope fractionations occur during the first, uncatalyzed stage of TSR, 12.4‰ for H2S and as much as 22.2‰ for BT. The fractionations decrease as the H2S concentration increases and the reaction enters the second, catalyzed stage. Once all of the oxidizable hydrocarbons have been consumed, sulfate reduction ceases and equilibrium partitioning then dictates the fractionation between H2S and sulfate (∼17‰).

  14. Study of thermochemical sulfate reduction mechanism using compound specific sulfur isotope analysis

    Science.gov (United States)

    Meshoulam, Alexander; Ellis, Geoffrey S.; Said Ahmad, Ward; Deev, Andrei; Sessions, Alex L.; Tang, Yongchun; Adkins, Jess F.; Liu, Jinzhong; Gilhooly, William P.; Aizenshtat, Zeev; Amrani, Alon

    2016-09-01

    The sulfur isotopic fractionation associated with the formation of organic sulfur compounds (OSCs) during thermochemical sulfate reduction (TSR) was studied using gold-tube pyrolysis experiments to simulate TSR. The reactants used included n-hexadecane (n-C16) as a model organic compound with sulfate, sulfite, or elemental sulfur as the sulfur source. At the end of each experiment, the S-isotopic composition and concentration of remaining sulfate, H2S, benzothiophene, dibenzothiophene, and 2-phenylthiophene (PT) were measured. The observed S-isotopic fractionations between sulfate and BT, DBT, and H2S in experimental simulations of TSR correlate well with a multi-stage model of the overall TSR process. Large kinetic isotope fractionations occur during the first, uncatalyzed stage of TSR, 12.4‰ for H2S and as much as 22.2‰ for BT. The fractionations decrease as the H2S concentration increases and the reaction enters the second, catalyzed stage. Once all of the oxidizable hydrocarbons have been consumed, sulfate reduction ceases and equilibrium partitioning then dictates the fractionation between H2S and sulfate (∼17‰). Experiments involving sparingly soluble CaSO4 show that during the second catalytic phase of TSR the rate of sulfate reduction exceeds that of sulfate dissolution. In this case, there is no apparent isotopic fractionation between source sulfate and generated H2S, as all of the available sulfate is effectively reduced at all reaction times. When CaSO4 is replaced with fully soluble Na2SO4, sulfate dissolution is no longer rate limiting and significant S-isotopic fractionation is observed. This supports the notion that CaSO4 dissolution can lead to the apparent lack of fractionation between H2S and sulfate produced by TSR in nature. The S-isotopic composition of individual OSCs record information related to geochemical reactions that cannot be discerned from the δ34S values obtained from bulk phases such as H2S, oil, and sulfate minerals, and

  15. Novel carbazole–pyridine copolymers by an economical method: synthesis, spectroscopic and thermochemical studies

    Directory of Open Access Journals (Sweden)

    Shahid Ameen Samra

    2011-05-01

    Full Text Available The synthesis, as well as spectroscopic and thermochemical studies of a novel class of carbazole-4-phenylpyridine co-polymers are described. The synthesis was carried out by a simple and cheaper method compared to the lengthy methods usually adopted for the preparation of carbazole–pyridine copolymers which involve costly catalysts. Thus, two series of polymers were synthesized by a modified Chichibabin reaction, i.e., by the condensation of diacetylated N-alkylcarbazoles with 3-substituted benzaldehydes in the presence of ammonium acetate in refluxing acetic acid. All the polymers were characterized by FTIR, 1H NMR, 13C NMR, UV–vis spectroscopy, fluorimetry, TGA and DSC. The weight average molecular masses (Mw of the polymers were estimated by the laser light scattering (LLS technique.

  16. Conceptual design study FY 1981: synfuels from fusion - using the tandem mirror reactor and a thermochemical cycle to produce hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Krikorian, O.H. (ed.)

    1982-02-09

    This report represents the second year's effort of a scoping and conceptual design study being conducted for the express purpose of evaluating the engineering potential of producing hydrogen by thermochemical cycles using a tandem mirror fusion driver. The hydrogen thus produced may then be used as a feedstock to produce fuels such as methane, methanol, or gasoline. The main objective of this second year's study has been to obtain some approximate cost figures for hydrogen production through a conceptual design study.

  17. Petroleum alteration by thermochemical sulfate reduction - A comprehensive molecular study of aromatic hydrocarbons and polar compounds

    Science.gov (United States)

    Walters, Clifford C.; Wang, Frank C.; Qian, Kuangnan; Wu, Chunping; Mennito, Anthony S.; Wei, Zhibin

    2015-03-01

    Thermochemical sulfate reduction (TSR) alters petroleum composition as it proceeds towards the complete oxidation of hydrocarbons to CO2. The effects of TSR on the molecular and isotopic composition of volatile species are well known; however, the non-volatile higher molecular weight aromatic and polar species have not been well documented. To address this deficiency, a suite of onshore Gulf coast oils and condensates generated from and accumulating in Smackover carbonates was assembled to include samples that experienced varying levels of TSR alteration and in reservoir thermal cracking. The entire molecular composition of aromatic hydrocarbons and NSO species were characterized and semi-quantified using comprehensive GC × GC (FID and CSD) and APPI-FTICR-MS. The concentration of thiadiamondoids is a reliable indicator of the extent of TSR alteration. Once generated by TSR, thiadiamondoids remain thermally stable in all but the most extreme reservoir temperatures (>180 °C). Hydrocarbon concentrations and distributions are influenced by thermal cracking and TSR. With increasing TSR alteration, oils become enriched in monoaromatic hydrocarbons and the distribution of high molecular weight aromatic hydrocarbons shifts towards more condensed species with a decrease in the number of alkyl carbons. Organosulfur compounds are created by the TSR process. In addition to the increase in benzothiophenes and dibenzothiophenes noted in previous studies, TSR generates condensed species containing one or more sulfur atoms that likely are composed of a single or multiple thiophenic cores. We hypothesize that these species are generated from the partial oxidation of PAHs and dealkylation reactions, followed by sulfur incorporation and condensation reactions. The organosulfur species remaining in the TSR altered oils are "proto-solid bitumen" moieties that upon further condensation, oxidation or sulfur incorporation result in highly sulfur enriched solid bitumen, which is

  18. Innovative solar thermochemical water splitting.

    Energy Technology Data Exchange (ETDEWEB)

    Hogan, Roy E. Jr.; Siegel, Nathan P.; Evans, Lindsey R.; Moss, Timothy A.; Stuecker, John Nicholas (Robocasting Enterprises, Albuquerque, NM); Diver, Richard B., Jr.; Miller, James Edward; Allendorf, Mark D. (Sandia National Laboratories, Livermore, CA); James, Darryl L. (Texas Tech University, Lubbock, TX)

    2008-02-01

    Sandia National Laboratories (SNL) is evaluating the potential of an innovative approach for splitting water into hydrogen and oxygen using two-step thermochemical cycles. Thermochemical cycles are heat engines that utilize high-temperature heat to produce chemical work. Like their mechanical work-producing counterparts, their efficiency depends on operating temperature and on the irreversibility of their internal processes. With this in mind, we have invented innovative design concepts for two-step solar-driven thermochemical heat engines based on iron oxide and iron oxide mixed with other metal oxides (ferrites). The design concepts utilize two sets of moving beds of ferrite reactant material in close proximity and moving in opposite directions to overcome a major impediment to achieving high efficiency--thermal recuperation between solids in efficient counter-current arrangements. They also provide inherent separation of the product hydrogen and oxygen and are an excellent match with high-concentration solar flux. However, they also impose unique requirements on the ferrite reactants and materials of construction as well as an understanding of the chemical and cycle thermodynamics. In this report the Counter-Rotating-Ring Receiver/Reactor/Recuperator (CR5) solar thermochemical heat engine and its basic operating principals are described. Preliminary thermal efficiency estimates are presented and discussed. Our ferrite reactant material development activities, thermodynamic studies, test results, and prototype hardware development are also presented.

  19. Thermochemical treatment of sewage sludge ashes for phosphorus recovery.

    Science.gov (United States)

    Adam, C; Peplinski, B; Michaelis, M; Kley, G; Simon, F-G

    2009-03-01

    Phosphorus (P) is an essential element for all living organisms and cannot be replaced. Municipal sewage sludge is a carrier of phosphorus, but also contains organic pollutants and heavy metals. A two-step thermal treatment is suggested, including mono-incineration of sewage sludge and subsequent thermochemical treatment of the ashes. Organic pollutants are completely destroyed by mono-incineration. The resulting sewage sludge ashes contain P, but also heavy metals. P in the ashes exhibits low bioavailability, a disadvantage in farming. Therefore, in a second thermochemical step, P is transferred into mineral phases available for plants, and heavy metals are removed as well. The thermochemical treatment was investigated in a laboratory-scale rotary furnace by treating seven different sewage sludge ashes under systematic variation of operational parameters. Heavy metal removal and the increase of the P-bioavailability were the focus of the investigation. The present experimental study shows that these objectives have been achieved with the proposed process. The P-bioavailability was significantly increased due to the formation of new mineral phases such as chlorapatite, farringtonite and stanfieldite during thermochemical treatment.

  20. Thermochemical Process Development Unit

    Data.gov (United States)

    Federal Laboratory Consortium — This facility is used to demonstrate and evaluate the thermochemical conversion of biomass to produce syngas or pyrolysis oil that can be further converted to fuels...

  1. Multiscale modeling and experimental interpretation of perovskite oxide materials in thermochemical energy storage and conversion for application in concentrating solar power

    Science.gov (United States)

    Albrecht, Kevin J.

    Decarbonization of the electric grid is fundamentally limited by the intermittency of renewable resources such as wind and solar. Therefore, energy storage will play a significant role in the future of grid-scale energy generation to overcome the intermittency issues. For this reason, concentrating solar power (CSP) plants have been a renewable energy generation technology of interest due to their ability to participate in cost effective and efficient thermal energy storage. However, the ability to dynamically dispatch a CSP plant to meet energy demands is currently limited by the large quantities of sensible thermal energy storage material needed in a molten salt plant. Perovskite oxides have been suggested as a thermochemical energy storage material to enhance the energy storage capabilities of particle-based CSP plants, which combine sensible and chemical modes of energy storage. In this dissertation, computational models are used to establish the thermochemical energy storage potential of select perovskite compositions, identify system configurations that promote high values of energy storage and solar-to-electric efficiency, assess the kinetic and transport limitation of the chemical mode of energy storage, and create receiver and reoxidation reactor models capable of aiding in component design. A methodology for determining perovskite thermochemical energy storage potential is developed based on point defect models to represent perovskite non-stoichiometry as a function of temperature and gas phase oxygen partial pressure. The thermodynamic parameters necessary for the model are extracted from non-stoichiometry measurements by fitting the model using an optimization routine. The procedure is demonstrated for Ca0.9Sr0.1MnO 3-d which displayed combined energy storage values of 705.7 kJ/kg -1 by cycling between 773 K and 0.21 bar oxygen to 1173 K and 10 -4 bar oxygen. Thermodynamic system-level models capable of exploiting perovskite redox chemistry for energy

  2. Thermochemical Stability Study of Alkyl-Tethered Quaternary Ammonium Cations for Anion Exchange Membrane Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Mohanty, Angela D.; Tignor, Steven E.; Sturgeon, Matthew R.; Long, Hai; Pivovar, Bryan S.; Bae, Chulsung

    2017-01-01

    The increased interest in the use of anion exchange membranes (AEMs) for applications in electrochemical devices has prompted significant efforts in designing materials with robust stability in alkaline media. Most reported AEMs suffer from polymer backbone degradation as well as cation functional group degradation. In this report, we provide comprehensive experimental investigations for the analysis of cation functional group stability under alkaline media. A silver oxide-mediated ion exchange method and an accelerated stability test in aqueous KOH solutions at elevated temperatures using a Parr reactor were used to evaluate a broad scope of quaternary ammonium (QA) cationic model compound structures, particularly focusing on alkyl-tethered cations. Additionally, byproduct analysis was employed to gain better understanding of degradation pathways and trends of alkaline stability. Experimental results under different conditions gave consistent trends in the order of cation stability of various QA small molecule model compounds. Overall, cations that are benzyl-substituted or that are near to electronegative atoms (such as oxygen) degrade faster in alkaline media in comparison to alkyl-tethered QAs. These comprehensive model compound stability studies provide valuable information regarding the relative stability of various cation structures and can help guide researchers towards designing new and promising candidates for AEM materials.

  3. H2-assisted CO2 thermochemical reduction on La0.9Ca0.1FeO3-δ membranes: a kinetics study

    KAUST Repository

    Wu, Xiao-Yu

    2017-11-04

    Kinetics data for CO2 thermochemical reduction in an isothermal membrane reactor is required to identify the rate-limiting steps. Here, we report a detailed reaction kinetics study on this process supported by an La0.9Ca0.1FeO3-δ (LCF-91) membrane. The dependence of CO2 reduction rate on various operating conditions is examined such as CO2 concentration on the feed side, fuel concentrations on the sweep side and temperatures. CO2 reduction rate is proportional to the oxygen flux across the membrane, and the measured maximum fluxes are 0.191 and 0.164 μmol cm-2 s-1 with 9.5% H2 and 11.6% CO on the sweep side at 990oC, respectively. Fuel is used to maintain the chemical potential gradient across the membrane and CO is used by construction to derive the surface reaction kinetics. This membrane also exhibits stable performances for 106 hours. A resistance-network model is developed to describe the oxygen transport process and the kinetics data are parameterized using the experimental values. The model shows a transition of the rate limiting step between the surface reactions on the feed side and the sweep side depending on the operating conditions.

  4. A hydrophobic gel phantom for study of thermochemical ablation: initial results using a weak acid and weak base.

    Science.gov (United States)

    Misselt, Andrew J; Edelman, Theresa L; Choi, Jeung H; Bischof, John C; Cressman, Erik N K

    2009-10-01

    To develop a model for study of exothermic chemical reactions potentially useful for tissue ablation. Seven gelatins ranging from 0.5% to 30% wt/vol with and without 15% or 30% caps and several commercial gels were evaluated. Baseline temperature measurements were taken. Acetic acid and ammonium hydroxide were sequentially injected over periods of 10-15 seconds in 1-mL aliquots, forming a discrete aqueous reaction chamber. Congo red pH indicator was included to assess the reaction. A thermocouple allowed data collection at completion of injection and every 15 seconds for 5 minutes. Injections were performed in triplicate, and average temperatures for each time point were reported. Gelatins fractured or refluxed even at the lowest concentrations tested. Most commercial gels proved too viscous and likewise led to reflux along the needle tract. A mineral oil-based gel was selected because of its ability to form a chamber without reflux or fracture and its clear colorless character, hydrophobic nature, chemical stability, viscosity, specific gravity, and cost. Temperatures during the first 60 seconds of the neutralization reaction showed an immediate increase that correlated well with concentration. The oil gel phantom is a safe, useful, readily available, inexpensive model to study mixing behaviors and maximum heating potentials for reactions that may prove useful in thermochemical tissue ablation for oncologic interventions. Measurable temperature changes occurred even at the lowest concentrations, and higher concentrations produced a greater release of heat energy.

  5. Thermochemical surface engineering of steels

    DEFF Research Database (Denmark)

    Thermochemical Surface Engineering of Steels provides a comprehensive scientific overview of the principles and different techniques involved in thermochemical surface engineering, including thermodynamics, kinetics principles, process technologies and techniques for enhanced performance of steels...

  6. Thermochemical and phase diagram studies of the Bi-Ni-Sn system

    Energy Technology Data Exchange (ETDEWEB)

    Milcheva, N. [Faculty of Chemistry, University of Plovdiv, 24 Tsar Asen str., 4000 Plovdiv (Bulgaria); Broz, P. [Masaryk University, Faculty of Science, Kotlarska 2, 61137 Brno (Czech Republic); Masaryk University, Central European Institute of Technology, CEITEC, Kamenice 753/5, 625 00, Brno (Czech Republic); Bursik, J. [Institute of Physics of Materials, Academy of Sciences, Zizkova 22, 61662 Brno (Czech Republic); Vassilev, G.P., E-mail: gpvassilev@uni.plovdiv.bg [Faculty of Chemistry, University of Plovdiv, 24 Tsar Asen str., 4000 Plovdiv (Bulgaria)

    2012-04-20

    Highlights: Black-Right-Pointing-Pointer We study the phase diagram Bi-Ni-Sn by using scanning electron microscopy and differential scanning calorimetry. Black-Right-Pointing-Pointer The samples are positioned in 3 isopleths with constant Ni contents of 0.05, 0.10 and 0.15 mol fraction. Black-Right-Pointing-Pointer It has been confirmed that a ternary eutectic reaction appears at around 116-129 Degree-Sign C. Black-Right-Pointing-Pointer Experimental liquidus temperatures were obtained and compared to calculated ones. Black-Right-Pointing-Pointer Six groups of thermal arrests were registered (except the eutectic and liquidus related peaks). - Abstract: The phase diagram Bi-Ni-Sn was studied by means of SEM (scanning electron microscopy)/EDS (energy-dispersive solid state spectrometry), by DSC (differential scanning calorimetry) and RT-XRD (room temperature X-Ray diffraction) in order to attain more information about this ternary phase diagram. The samples were positioned in three isopleths with nickel contents of: 0.05 (section 1), 0.10 (section 2) and 0.15 (section 3) mole fractions, respectively. The mole fractions of Sn corresponding to the particular sections were as follows: from 0.19 to 0.76 (section 1), from 0.18 to 0.72 (section 2); from 0.17 to 0.68 (section 3). Mixtures of pure metals were sealed under vacuum in amorphous silica ampoules and annealed at 350 Degree-Sign C. A binary Bi-Sn eutectic sample was synthesized and used as internal standard. The existence of a previously reported ternary eutectic reaction was confirmed. Liquidus temperatures were identified and the results were compared to CALPHAD-type calculations. It was found that ternary samples' liquidus temperatures were higher than the calculated ones. Six more groups of thermal arrests were registered except the eutectic and liquidus related peaks.

  7. EERA Bioenergy. Thermochemical Processing

    Energy Technology Data Exchange (ETDEWEB)

    Sipilaa, K.; Wilen, C. [VTT Technical Research Centre of Finland, Laskut (Finland); Kiel, J. [ECN Biomass, Coal and Environmental Research, Petten (Netherlands); Girio, F. [Laboratorio Nacional de Energia e Geologia LNEG, Lisboa (Portugal); Pilegaard, K. [Risoe, Roskilde (Denmark); Gabrielle, B. [Environment and Arable Crops Research Unit, Institut National de la Recherche Agronomique INRA, Thiverval-Grignon (France); Van Bree, B. [ECN Policy Studies, Energy research Centre of the Netherlands ECN, Petten (Netherlands)

    2011-04-15

    One of the joint programmes within EERA (European Energy Research Alliance) concerns bioenergy. In this presentation background information is given on the EERA, focusing on the bioenergy programme. And more in particular on the bioenergy sub-programme thermochemical processes. The current focus of EERA Bioenergy is on biofuels.

  8. Comparative studies on thermochemical characterization of corn stover pretreated by white-rot and brown-rot fungi.

    Science.gov (United States)

    Zeng, Yelin; Yang, Xuewei; Yu, Hongbo; Zhang, Xiaoyu; Ma, Fuying

    2011-09-28

    The effects of white-rot and brown-rot fungal pretreatment on the chemical composition and thermochemical conversion of corn stover were investigated. Fungus-pretreated corn stover was analyzed by Fourier transform infrared spectroscopy and X-ray diffraction analysis to characterize the changes in chemical composition. Differences in thermochemical conversion of corn stover after fungal pretreatment were investigated using thermogravimetric and pyrolysis analysis. The results indicated that the white-rot fungus Irpex lacteus CD2 has great lignin-degrading ability, whereas the brown-rot fungus Fomitopsis sp. IMER2 preferentially degrades the amorphous regions of the cellulose. The biopretreatment favors thermal decomposition of corn stover. The weight loss of IMER2-treated acid detergent fiber became greater, and the oil yield increased from 32.7 to 50.8%. After CD2 biopretreatment, 58% weight loss of acid detergent lignin was achieved and the oil yield increased from 16.8 to 26.8%.

  9. Thermochemical and phase diagram studies of the Sn-Zn-Ni system

    Energy Technology Data Exchange (ETDEWEB)

    Gandova, V.D. [Faculty of Chemistry, University of Plovdiv, 24 Tsar Asen Str., 4000 Plovdiv (Bulgaria); Broz, P. [Masaryk University, Faculty of Science, Department of Chemistry, Kotlarska 2, 61137 Brno (Czech Republic); Bursik, J. [Institute of Physics of Materials, Academy of Sciences, Zizkova 22, 61662, Brno (Czech Republic); Vassilev, G.P., E-mail: gpvassilev@excite.com [Faculty of Chemistry, University of Plovdiv, 24 Tsar Asen Str., 4000 Plovdiv (Bulgaria)

    2011-09-20

    Highlights: {yields} Sn-Zn-Ni phase diagram in the vicinity of the Sn-Zn system. {yields} Unidentified compositions (UX1-UX4) are repeatedly observed. {yields} This indicates up to 6 ternary compounds in the system. {yields} A ternary eutectic reaction at around 190 {sup o}C is found. - Abstract: The phase diagram Sn-Zn-Ni was studied by means of DSC and electron microprobe analysis. The samples were positioned in three isopleth sections with nickel contents of 0.04 (section 1), 0.08 (section 2) and 0.12 (section 3) mole fractions. The mole fractions of Sn corresponding to the particular sections were as follows: from 0.230 to 0.768 (section 1), from 0.230 to 0.736 (section 2); from 0.220 to 0.704 (section 3). Mixtures of pure metals were sealed under vacuum in quartz ampoules and annealed at 350 {sup o}C. The solid phases identified in the samples were: {gamma}-(i.e. Ni{sub 5}Zn{sub 21}), (Zn) and the ternary phase T1. Unidentified compositions were observed. One of them: UX1 (X{sub Ni} = 0.071 {+-} 0.005, X{sub Sn} = 0.439 {+-} 0.009 and X{sub Zn} = 0.490 {+-} 0.010) might indicate another (stable or metastable) ternary compound (T3) in the system Sn-Zn-Ni. Considering the data obtained by combining DSC with microstructure observations, the studied alloys could be divided in two groups (A and B). A ternary eutectic reaction at around 190 {sup o}C is common for the A-group alloys. The phases taking part in this reaction are, probably, Ni{sub 5}Zn{sub 21}, (Zn), ({beta}Sn) and liquid. B-group samples do not show ternary eutectic reaction and are also characterized by the presence of the ternary compound T1 (absent in the A-group alloys). Four other groups of thermal arrests were registered (TA{sub 1}-TA{sub 4}). It was found that TA{sub 2} peaks were characteristic for most of the A-group samples, while TA{sub 1} peaks were registered with all B-group samples.

  10. Pyrolysis kinetics study of three biomass solid wastes for thermochemical conversion into liquid fuels

    Science.gov (United States)

    Tuly, S. S.; Parveen, M.; Islam, M. R.; Rahman, M. S.; Haniu, H.

    2017-06-01

    Pyrolysis has been considered as the most efficient way of producing liquid fuel from biomass and its wastes. In this study the thermal degradation characteristics and pyrolysis kinetics of three selected biomass samples of Jute stick (Corchorus capsularis), Japanese cedar wood (Cryptomeria japonica) and Tamarind seed (Tamarindus indica) have been investigated in a nitrogen atmosphere at heating rates of 10°C/min and 60°C/min over a temperature range of 30°C to 800°C. The weight loss region for the three biomass solid wastes has shifted to a higher temperature range and the weight loss rate has increased with increasing heating rate. In this case, the three biomass samples have represented the similar behavior. The initial reaction temperature has decreased with increasing heating rate but the reaction range and reaction rate have increased. The percentage of total weight loss is higher for cedar wood than jute stick and tamarind seed. For the three biomass wastes, the overall rate equation has been modeled properly by one simplified equation and from here it is possible to determine kinetic parameters of unreacted materials based on Arrhenious form. The calculated rate equation compares thoroughly well with the measured TG and DTG data.

  11. Thermochemical study of vaporization of ceramic breeding materials by Knudsen effusion mass spectrometry

    Science.gov (United States)

    Yamawaki, Michio; Yamaguchi, Kenji; Yasumoto, Masaru

    1991-03-01

    In order to evaluate the applicability of Li 2SnO 3 as a tritium breeding blanket material of a fusion reactor, a thermodynamic study of the vaporization of solid Li 2SnO 3 was performed by Knudsen effusion mass spectrometry. Partial vapor pressures of Li(g), O 2(g), LiO(g), Li 2O(g) and SnO(g) were determined over Li 2SnO 3. The measured partial pressure of Li(g) over Li 2SnO 3 is relatively high and ranks between those of Li 2SiO 3 and Li 2TiO 3. The Gibbs energy of formation of Li 2SnO 3 was obtained in the temperature range of 1455 to 1590 K. Computer calculations by use of the SOLGASMIX code proved that Li 2SnO 3 can show excellent performance as a breeder material with regard to tritium recovery and compatibility with stainless steel.

  12. Study on a lab-scale hydrogen production by closed cycle thermo-chemical iodine-sulfur process

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, P.; Chen, S.Z.; Wang, L.J.; Yao, T.Y.; Xu, J.M. [Institute of Nuclear and New Energy Technology, Tsinghua University, P.O. Box 1021, Beijing (China)

    2010-10-15

    The Iodine-Sulfur (IS) thermo-chemical process for the production of hydrogen is one of the most promising approaches for use of the high temperature process heat supplied by high temperature reactor, which was developed in the Institute of nuclear and new energy technology (INET) of Tsinghua University, China, and INET initiated the fundamental studies on IS cycle since 2005. Based on the experiment results obtained by fundamental researches, a lab-scaled closed cycle loop (IS-10), which featured in electro-electrodialysis (EED) for hydriodic acid (HI) concentration, was designed and built at INET. The loop was composed of three sections, i.e., Bunsen section, HI section and sulfuric acid section. The closed cycle experiment on the loop was successfully carried out recently. In HI section, HI{sub x} produced by Bunsen reaction was continuously purified through reverse Bunsen reaction, concentrated by EED, and then HI solution was obtained by distillation. Finally HI was catalytically decomposed to H{sub 2} and I{sub 2} with the conversion of 20%. In sulfuric acid section, sulfuric acid was continuously purified, concentrated by distillation, and catalytically decomposed to SO{sub 2}, O{sub 2} and H{sub 2}O with the conversion of 75%. In Bunsen section, water, including recycled water, reacted with I{sub 2} and SO{sub 2} recycled from HI section and sulfuric acid section to form two separated acids phases, thus to form a closed cycle. The closed cycle experiment lasted for 7 h with the hydrogen production rate of 10 NL/h, with Pt loaded on activated carbon and copper chromite used as the catalysts for HI and sulfuric acid decomposition, respectively. This paper summarizes the main features of IS-10 and the main results of the closed cycle experiment. So far IS-10 is the second reported facility on which closed experiment was carried out, and the first one with EED embedded to perform a closed cycle operation. (author)

  13. Advanced Electrochemical Technologies for Hydrogen Production by Alternative Thermochemical Cycles

    Energy Technology Data Exchange (ETDEWEB)

    Lvov, Serguei; Chung, Mike; Fedkin, Mark; Lewis, Michele; Balashov, Victor; Chalkova, Elena; Akinfiev, Nikolay; Stork, Carol; Davis, Thomas; Gadala-Maria, Francis; Stanford, Thomas; Weidner, John; Law, Victor; Prindle, John

    2011-01-06

    Hydrogen fuel is a potentially major solution to the problem of climate change, as well as addressing urban air pollution issues. But a key future challenge for hydrogen as a clean energy carrier is a sustainable, low-cost method of producing it in large capacities. Most of the world's hydrogen is currently derived from fossil fuels through some type of reforming processes. Nuclear hydrogen production is an emerging and promising alternative to the reforming processes for carbon-free hydrogen production in the future. This report presents the main results of a research program carried out by a NERI Consortium, which consisted of Penn State University (PSU) (lead), University of South Carolina (USC), Tulane University (TU), and Argonne National Laboratory (ANL). Thermochemical water decomposition is an emerging technology for large-scale production of hydrogen. Typically using two or more intermediate compounds, a sequence of chemical and physical processes split water into hydrogen and oxygen, without releasing any pollutants externally to the atmosphere. These intermediate compounds are recycled internally within a closed loop. While previous studies have identified over 200 possible thermochemical cycles, only a few have progressed beyond theoretical calculations to working experimental demonstrations that establish scientific and practical feasibility of the thermochemical processes. The Cu-Cl cycle has a significant advantage over other cycles due to lower temperature requirements – around 530 °C and below. As a result, it can be eventually linked with the Generation IV thermal power stations. Advantages of the Cu-Cl cycle over others include lower operating temperatures, ability to utilize low-grade waste heat to improve energy efficiency, and potentially lower cost materials. Another significant advantage is a relatively low voltage required for the electrochemical step (thus low electricity input). Other advantages include common chemical agents and

  14. Thermochemical Storage of Middle Temperature Wasted Heat by Functionalized C/Mg(OH2 Hybrid Materials

    Directory of Open Access Journals (Sweden)

    Emanuela Mastronardo

    2017-01-01

    Full Text Available For the thermochemical performance implementation of Mg(OH2 as a heat storage medium, several hybrid materials have been investigated. For this study, high-performance hybrid materials have been developed by exploiting the authors’ previous findings. Expanded graphite (EG/carbon nanotubes (CNTs-Mg(OH2 hybrid materials have been prepared through Mg(OH2 deposition-precipitation over functionalized, i.e., oxidized, or un-functionalized EG or CNTs. The heat storage performances of the carbon-based hybrid materials have been investigated through a laboratory-scale experimental simulation of the heat storage/release cycles, carried out by a thermogravimetric apparatus. This study offers a critical evaluation of the thermochemical performances of developed materials through their comparison in terms of heat storage and output capacities per mass and volume unit. It was demonstrated that both EG and CNTs improves the thermochemical performances of the storage medium in terms of reaction rate and conversion with respect to pure Mg(OH2. With functionalized EG/CNTs-Mg(OH2, (i the potential heat storage and output capacities per mass unit of Mg(OH2 have been completely exploited; and (ii higher heat storage and output capacities per volume unit were obtained. That means, for technological applications, as smaller volume at equal stored/released heat.

  15. LASL thermochemical hydrogen status on September 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Cox, K.E.

    1979-01-01

    The work described in this report was accomplished during the period October 1, 1978 to September 30, 1979. Most of the effort was applied to a study of the Los Alamos Scientific Laboratory (LASL) hybrid bismuth sulfate cycle. The work included a conceptual design of the cycle and experimental work to verify the design conditions. Key findings were: a 50.8% efficiency was obtained when an improved cycle design was coupled to a fusion energy source at 1500 K; experimental results showed an endothermic heat requirement of +172 kJ/mol for the decomposition of Bi/sub 2/O/sub 3/.2SO/sub 3/ to Bi/sub 2/O/sub 3/.SO/sub 3/, and SO/sub 3/; reaction times for bismuth sulfate decomposition were determined as a function of temperature. At 1240 K, < 1.5 min were required for the first two stages of decomposition from Bi/sub 2/O/sub 3/.3SO/sub 3/ to Bi/sub 2/O/sub 3/; tests made to determine the feasibility of decomposing Bi/sub 2/O/sub 3/.2SO/sub 3/ in a 1 inch diameter rotary kiln showed that Bi/sub 2/O/sub 3/.2SO/sub 3/ could be decomposed continuously. In related work, support was given to the DOE Thermochemical Cycle Evaluation Panel (Funk). The Second Annual International Energy Agency (IEA) Workshop on Thermochemical Hydrogen Production from Water met on September 24 to 27, 1979 at Los Alamos.

  16. Thermochemical destruction of asbestos-containing roofing slate and the feasibility of using recycled waste sulfuric acid

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Seong-Nam, E-mail: namsn76@gmail.com [Engineering Research Institute, Seoul National University, Daehak-dong, Gwanak-gu 151-744 (Korea, Republic of); Jeong, Seongkyeong [Environmental Resource Recirculation Division, National Institute of Environmental Research, Environmental Research Complex, Kyeongseo-dong, Seo-gu, Incheon 404-708 (Korea, Republic of); Lim, Hojoo [Indoor Environment and Noise Division, National Institute of Environmental Research, Environmental Research Complex, Kyeongseo-dong, Seo-gu, Incheon 404-708 (Korea, Republic of)

    2014-01-30

    Highlights: • Asbestos-containing roofing slates (ACS) were thermochemically treated. • 5 N H{sub 2}SO{sub 4} with 100 °C heating for 10–24 h showed complete disappearance. • Asbestiform of ACS was changed to non-asbestiform after treatment. • Favorable destruction was occurred at the Mg(OH){sub 2} layer rather than SiO{sub 2} sheet. • Equivalent treatability of waste acid brightened the feasibility of this approach. -- Abstract: In this study, we have investigated the feasibility of using a thermochemical technique on ∼17% chrysotile-containing roofing sheet or slate (ACS), in which 5 N sulfuric acid-digestive destruction was incorporated with 10–24-h heating at 100 °C. The X-ray diffraction (XRD) and the polarized light microscopy (PLM) results have clearly shown that raw chrysotile asbestos was converted to non-asbestiform material with no crystallinity by the low temperature thermochemical treatment. As an alternative to the use of pricey sulfuric acid, waste sulfuric acid discharged from a semiconductor manufacturing process was reused for the asbestos-fracturing purpose, and it was found that similar removals could be obtained under the same experimental conditions, promising the practical applicability of thermochemical treatment of ACWs. A thermodynamic understanding based on the extraction rates of magnesium and silica from a chrysotile structure has revealed that the destruction of chrysotile by acid-digestion is greatly influenced by the reaction temperatures, showing a 80.3-fold increase in the reaction rate by raising the temperature by 30–100 °C. The overall destruction is dependent upon the breaking-up of the silicon-oxide layer – a rate-limiting step. This study is meaningful in showing that the low temperature thermochemical treatment is feasible as an ACW-treatment method.

  17. Experimental investigation and model validation of a CaO/Ca(OH)2 fluidized bed reactor for thermochemical energy storage applications

    OpenAIRE

    Álvarez Criado, Yolanda; Huille, Alfred; Rougé, Sylvie; Abanades García, Juan Carlos

    2016-01-01

    The CaO/Ca(OH)2 hydration/dehydration chemical loop has long been recognized as a potential candidate for application in energy storage systems for concentrated solar plants. However, the technology still remains at a conceptual level because little information has been published on the performance of the key reactors in the system. In this work, we experimentally investigate the hydration and dehydration reactors in a 5.5 kWth batch fluidized bed reactor, in conditions relevant to larger sys...

  18. Thermochemical pretreatments for enhancing succinic acid production from industrial hemp (Cannabis sativa L.)

    DEFF Research Database (Denmark)

    Gunnarsson, Ingólfur Bragi; Kuglarz, Mariusz; Karakashev, Dimitar Borisov

    2015-01-01

    The aim of this study was to develop an efficient thermochemical method for treatment of industrial hemp biomass, in order to increase its bioconversion to succinic acid. Industrial hemp was subjected to various thermochemical pretreatments using 0-3% H2SO4, NaOH or H2O2 at 121-180°C prior...

  19. Capabilities to Support Thermochemical Hydrogen Production Technology Development

    Energy Technology Data Exchange (ETDEWEB)

    Daniel M. Ginosar

    2009-05-01

    This report presents the results of a study to determine if Idaho National Laboratory (INL) has the skilled staff, instrumentation, specialized equipment, and facilities required to take on work in thermochemical research, development, and demonstration currently being performed by the Nuclear Hydrogen Initiative (NHI). This study outlines the beneficial collaborations between INL and other national laboratories, universities, and industries to strengthen INL's thermochemical efforts, which should be developed to achieve the goals of the NHI in the most expeditious, cost effective manner. Taking on this work supports INL's long-term strategy to maintain leadership in thermochemical cycle development. This report suggests a logical path forward to accomplish this transition.

  20. Thermochemical conversion of biomass to synthetic fuels in a large experimental facility. Gasification Research on Wood (GROW) Project, April 1981-March 1982

    Energy Technology Data Exchange (ETDEWEB)

    Flanigan, V.J.; Findley, M.E.; Sineath, H.H.

    1982-01-01

    A description of the Phase II segment of the GROW project is presented. In Phase II, operational experimentation of the 40-inch diameter, fluidized bed reactor at the University of Missouri-Rolla was continued. Recycle gas and catalyst and carbon dioxide scrubbing were used in an attempt to improve the quality of the gas. A description of the operation and the results of the tests with wood feed material and the conclusions drawn from the results are discussed. In general, recycling produced little improvement over air-blown gasification. The low temperatures caused by the heat consumption of the recycle gas and dilution of the oxygen appeared to be responsible. Both of these effects required a greater amount of air to maintain a given reactor temperature. With few exceptions, use of recycle gas in the operation of the reactor was adequate and safe. The effect of stripping carbon dioxide from the recycle gas was what was anticipated. The hydrogen content of the gas increased, and the carbon monoxide content decreased when recycle gas was used. Greater changes in the hydrogen and carbon monoxide occurred when potassium carbonate and a wood ash catalyst were used. However, use of the catalyst tended to cause fusing of the bed.

  1. Hybrid Thermochemical/Biological Processing

    Science.gov (United States)

    Brown, Robert C.

    The conventional view of biorefineries is that lignocellulosic plant material will be fractionated into cellulose, hemicellulose, lignin, and terpenes before these components are biochemically converted into market products. Occasionally, these plants include a thermochemical step at the end of the process to convert recalcitrant plant components or mixed waste streams into heat to meet thermal energy demands elsewhere in the facility. However, another possibility for converting high-fiber plant materials is to start by thermochemically processing it into a uniform intermediate product that can be biologically converted into a bio-based product. This alternative route to bio-based products is known as hybrid thermochemical/biological processing. There are two distinct approaches to hybrid processing: (a) gasification followed by fermentation of the resulting gaseous mixture of carbon monoxide (CO), hydrogen (H2), and carbon dioxide (CO2) and (b) fast pyrolysis followed by hydrolysis and/or fermentation of the anhydrosugars found in the resulting bio-oil. This article explores this "cart before the horse" approach to biorefineries.

  2. Recent Developments in Factsage Thermochemical Software and Databases

    Science.gov (United States)

    Bale, Christopher W.; Bélisle, E.; Chartrand, P.; Decterov, S. A.; Eriksson, G.; Gheribi, A.; Hack, K.; Jung, I.-H.; Melançon, J.; Pelton, A. D.; Petersen, S.; Robelin, C.

    The FactSage® package consists of a series of information, database and calculation modules that enable one to access pure substances and solution databases and perform thermochemical equilibrium calculations. FactSage was originally founded by process pyrometallurgists and has since expanded its applications to include hydrometallurgy, electrometallurgy, corrosion, glass technology, combustion, ceramics, geology, environmental studies, etc. With the various modules one can perform a wide variety of thermochemical calculations and generate tables and graphs of complex chemical equilibria and phase diagrams for multicomponent systems.

  3. Experimental and Numerical Study on Shock Layer Radiation for Planetary Entry Flights

    OpenAIRE

    山田, 剛治; 吾郷, 祥太; 久保, 優斗; 松野, 隆; 川添, 博光; Yamada, Gouji; Ago, Shota; Kubo, Yuto; Matsuno, Takashi; Kawazoe, Hiromitsu

    2013-01-01

    In this study, shock layer radiation is investigated by experimental and numerical approach. Radiation profiles of N2, N2(+), and N are observed in two test conditions of initial pressure and velocity by time-resolved emission spectroscopy. Flow properties behind shock front are computed by the CFD code with two-temperature thermochemical model. The results are used as inputs for the radiation analysis code “SPRADIAN 2” to derive the radiation profiles behind shock front along the line of sig...

  4. Probabilistic thermo-chemical analysis of a pultruded composite rod

    NARCIS (Netherlands)

    Baran, Ismet; Tutum, Cem C.; Hattel, Jesper H.

    2012-01-01

    In the present study the deterministic thermo-chemical pultrusion simulation of a composite rod taken from the literature [7] is used as a validation case. The predicted centerline temperature and cure degree profiles of the rod match well with those in the literature [7]. Following the validation

  5. Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-10

    Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

  6. Effects of coal-derived trace species on the performance of molten carbonate fuel cells. Topical report on thermochemical studies

    Energy Technology Data Exchange (ETDEWEB)

    Pigeaud, A.

    1991-10-01

    The overall objective of the present study was to determine in detail the interaction effects of 10 simultaneously present, coal-gas contaminants, both on each other and on components of the Carbonate Fuel Cell. The primary goal was to assess underlying chemistries and reaction mechanisms which may cause decay in fuel cell performance or endurance as a result of both physics-chemical and/or mechanical interactions with the cell components and internal fuel cell parts. It was found, both from theory and cell test evidence, that trace contaminant interactions may occur with: Fuel-cell Electrodes (e.g., in this study with the Ni-anode), Lithium/Potassium Carbonate Electrolyte, Nickel and SS-Hardware, and by Mechanical Obstruction of Gas Flow in the Anode Plenum.

  7. Biomass Thermochemical Conversion Program: 1986 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

    1987-01-01

    Wood and crop residues constitute a vast majority of the biomass feedstocks available for conversion, and thermochemical processes are well suited for conversion of these materials. Thermochemical conversion processes can generate a variety of products such as gasoline hydrocarbon fuels, natural gas substitutes, or heat energy for electric power generation. The US Department of Energy is sponsoring research on biomass conversion technologies through its Biomass Thermochemical Conversion Program. Pacific Northwest Laboratory has been designated the Technical Field Management Office for the Biomass Thermochemical Conversion Program with overall responsibility for the Program. This report briefly describes the Thermochemical Conversion Program structure and summarizes the activities and major accomplishments during fiscal year 1986. 88 refs., 31 figs., 5 tabs.

  8. Kinetic and thermochemical studies of the ClO + ClO + M ↔ Cl2O2 + M reaction

    Science.gov (United States)

    Ferracci, V.; Rowley, D. M.

    2009-12-01

    ller, F. Stroh, Atmospheric Chemistry and Physics, 2007, 7, 3055 2. S. L. Nickolaisen, R. R. Friedl, S. P. Sander, Journal of Physical Chemistry, 1994, 98, 155 3. S. P. Sander, R. R. Friedl, D. M. Golden, M. J. Kurylo, R. E. Huie, V. L. Orkin, G. K. Moortgat, A. R. Ravishankara, C. E. Kolb, M. J. Molina, B. J. Finlayson-Pitts, Chemical Kinetics and Photochemical Data for use in Atmospheric Studies, Evaluation No. 14, JPL Publication 02-25, NASA Jet Propulsion Laboratory, Pasadena CA, 2003

  9. Quantitative Thermochemical Measurements in High-Pressure Gaseous Combustion

    Science.gov (United States)

    Kojima, Jun J.; Fischer, David G.

    2012-01-01

    We present our strategic experiment and thermochemical analyses on combustion flow using a subframe burst gating (SBG) Raman spectroscopy. This unconventional laser diagnostic technique has promising ability to enhance accuracy of the quantitative scalar measurements in a point-wise single-shot fashion. In the presentation, we briefly describe an experimental methodology that generates transferable calibration standard for the routine implementation of the diagnostics in hydrocarbon flames. The diagnostic technology was applied to simultaneous measurements of temperature and chemical species in a swirl-stabilized turbulent flame with gaseous methane fuel at elevated pressure (17 atm). Statistical analyses of the space-/time-resolved thermochemical data provide insights into the nature of the mixing process and it impact on the subsequent combustion process in the model combustor.

  10. Thermochemical properties of some alkaline-earth silicates and zirconates. Fission product behaviour during molten core-concrete interactions

    Energy Technology Data Exchange (ETDEWEB)

    Huntelaar, M.E.

    1996-06-19

    This thesis aims to make a contribution to a better understanding of the chemical processes occurring during an ex-vessel MCCI accident with a western-type of nuclear reactor. Chosen is for a detailed thermochemical study of the silicates and zirconates of barium and strontium. In Chapter one a short introduction in the history of (research in) nuclear safety is given, followed by the state-of-the-art of molten core-concrete interactions in Chapter two. In both Chapters the role of chemical thermodynamics on this particular subject is dealt with. The experimental work on the silicates and zirconates of barium and strontium performed for this thesis, is described in the Chapters three, four, five, six, and parts of eight. In Chapter three the basis for all thermochemical measurements, the sample preparation is given. Because the sample preparation effects the accuracy of the thermodynamic measurements, a great deal of effort is spent in optimizing the synthesis of the silicates which resulted in the TEOS-method widely employed here. In the next Chapters the different thermochemical techniques used, are described: The low-temperature heat capacity measurements and the enthalpy increment measurements in Chapter four, the enthalpy-of-solution measurements in Chapter five, and measurements to determine the crystal structures in Chapter six. (orig.).

  11. Biomass thermochemical conversion program. 1985 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

    1986-01-01

    Wood and crop residues constitute a vast majority of the biomass feedstocks available for conversion, and thermochemical processes are well suited for conversion of these materials. The US Department of Energy (DOE) is sponsoring research on this conversion technology for renewable energy through its Biomass Thermochemical Conversion Program. The Program is part of DOE's Biofuels and Municipal Waste Technology Division, Office of Renewable Technologies. This report briefly describes the Thermochemical Conversion Program structure and summarizes the activities and major accomplishments during fiscal year 1985. 32 figs., 4 tabs.

  12. Biomass thermochemical conversion program: 1987 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

    1988-01-01

    The objective of the Biomass Thermochemical Conversion Program is to generate a base of scientific data and conversion process information that will lead to establishment of cost-effective processes for conversion of biomass resources into clean fuels. To accomplish this objective, in fiscal year 1987 the Thermochemical Conversion Program sponsored research activities in the following four areas: Liquid Hydrocarbon Fuels Technology; Gasification Technology; Direct Combustion Technology; Program Support Activities. In this report an overview of the Thermochemical Conversion Program is presented. Specific research projects are then described. Major accomplishments for 1987 are summarized.

  13. Kinetics of thermochemical gas-solid reactions important in the Venus sulfur cycle

    Science.gov (United States)

    Fegley, Bruce, Jr.

    1988-01-01

    The thermochemical net reaction CaCO3 + SO2 yields CaSO4 + CO is predicted to be an important sink for incorporation of SO2 into the Venus crust. The reaction rate law was established to understand the dependence of rate on experimental variables such as temperature and partial pressure of SO2, CO2, and O2. The experimental approach was a variant of the thermogravimetric method often employed to study the kinetics of thermochemical gas-solid reactions. Clear calcite crystals were heated at constant temperature in SO2-bearing gas streams for varying time periods. Reaction rate was determined by three independent methods. A weighted linear least squares fit to all rate data yielded a rate equation. Based on the Venera 13, 14 and Vega 2 observations of CaO content of the Venus atmosphere, SO2 at the calculated rate would be removed from the Venus atmosphere in about 1,900,00 years. The most plausible endogenic source of the sulfur needed to replenish atmospheric SO2 is volcanism. The annual amount of erupted material needed for the replenishment depends on sulfur content; three ratios are used to calculate rates ranging from 0.4 to 11 cu km/year. This geochemically derived volcanism rate can be used to test if geophysically derived rates are correct. The work also suggests that Venus is less volcanically active than the Earth.

  14. Life cycle assessment of microalgae to biofuel: Thermochemical processing through hydrothermal liquefaction or pyrolysis

    Science.gov (United States)

    Bennion, Edward P.

    Microalgae are currently being investigated as a renewable transportation fuel feedstock based on various advantages that include high annual yields, utilization of poor quality land, does not compete with food, and can be integrated with various waste streams. This study focuses on directly assessing the impact of two different thermochemical conversion technologies on the microalgae-to-biofuel process through life cycle assessment. A system boundary of a "well to pump" (WTP) is defined and includes sub-process models of the growth, dewatering, thermochemical bio-oil recovery, bio-oil stabilization, conversion to renewable diesel, and transport to the pump. Models were validated with experimental and literature data and are representative of an industrial-scale microalgae-to-biofuel process. Two different thermochemical bio-oil conversion systems are modeled and compared on a systems level, hydrothermal liquefaction (HTL) and pyrolysis. The environmental impact of the two pathways were quantified on the metrics of net energy ratio (NER), defined here as energy consumed over energy produced, and greenhouse gas (GHG) emissions. Results for WTP biofuel production through the HTL pathway were determined to be 1.23 for the NER and GHG emissions of -11.4 g CO2 eq (MJ renewable diesel)-1. WTP biofuel production through the pyrolysis pathway results in a NER of 2.27 and GHG emissions of 210 g CO2 eq (MJ renewable diesel)-1. The large environmental impact associated with the pyrolysis pathway is attributed to feedstock drying requirements and combustion of co-products to improve system energetics. Discussion focuses on a detailed breakdown of the overall process energetics and GHGs, impact of modeling at laboratory-scale compared to industrial-scale, environmental impact sensitivity to engineering systems input parameters for future focused research and development, and a comparison of results to literature.

  15. EXPERIMENTAL STUDY IN NATURAL CONVECTION

    African Journals Online (AJOL)

    PROF. BARTH EKWEME

    The study of thermal and ventilation parameters, obtained in a transient, laminar solar chimney of reduced dimensions, (1 < m <3) m with a square collector (side = 2m) is presented. Experimental measurements has been made to determine the temperature of the absorber and the fluid in the collector, it is shown that at the ...

  16. Valorization of agroindustrial solid residues and residues from biofuel production chains by thermochemical conversion: a review, citing Brazil as a case study

    Directory of Open Access Journals (Sweden)

    E. Virmond

    2013-06-01

    Full Text Available Besides high industrial development, Brazil is also an agribusiness country. Each year about 330 million metrics tons (Mg of biomass residues are generated, requiring tremendous effort to develop biomass systems in which production, conversion and utilization of bio-based products are carried out efficiently and under environmentally sustainable conditions. For the production of biofuels, organic chemicals and materials, it is envisaged to follow a biorefinery model which includes modern and proven green chemical technologies such as bioprocessing, pyrolysis, gasification, Fischer-Tropsch synthesis and other catalytic processes in order to make more complex molecules and materials on which a future sustainable society will be based. This paper presents promising options for valorization of Brazilian agroindustrial biomass sources and residues originating from the biofuel production chains as renewable energy sources and addresses the main aspects of the thermochemical technologies which have been applied.

  17. Thermochemical parameters of caffeine, theophylline, and xanthine

    Energy Technology Data Exchange (ETDEWEB)

    Ngo Tuan Cuong; Truong Ba Tai [Department of Chemistry, and Mathematical Modeling and Computational Science Center (LMCC), Katholieke Universiteit Leuven, B-3001 Leuven (Belgium); Vu Thi Thu Ha [Institute of Chemistry, Vietnam Academy of Science and Technology, Hanoi (Viet Nam); Minh Tho Nguyen, E-mail: minh.nguyen@chem.kuleuven.b [Department of Chemistry, and Mathematical Modeling and Computational Science Center (LMCC), Katholieke Universiteit Leuven, B-3001 Leuven (Belgium)

    2010-04-15

    Thermochemical parameters of caffeine 1, theophylline 2, xanthine 3, uracil, and imidazole derivatives are determined by quantum chemical calculations. Using the composite G3B3 method, the standard heat of formation of caffeine in the gaseous phase amounts to DELTA{sub f}H{sub g}{sup 0}(1)=-243+-8kJ.mol{sup -1}, which lends a support for the recent experimental value of -237.0 +- 2.5 kcal . mol{sup -1}. We also obtain DELTA{sub f}H{sub g}{sup 0}(2)=-232+-8kJ.mol{sup -1}andDELTA{sub f}H{sub g}{sup 0}(3)=-209+-8kJ.mol{sup -1}. The adiabatic ionization energies are IE{sub a}(1) = 7.9 eV, IE{sub a}(2) = 8.1 eV, and IE{sub a}(3) = 8.5 eV using B3LYP calculations. The enhanced ability of caffeine to eject electron, as compared to the parent compounds and cyclic components, is of interest with regard to its potential use as a corrosion inhibitor.

  18. Salt impregnated desiccant matrices for ‘open’ thermochemical energy conversion and storage: improving energy density utilisation through hygrodynamic & thermodynamic reactor design

    OpenAIRE

    Casey, Sean P.; AYDIN, Devrim; Elvins, Jon; Riffat, Saffa

    2017-01-01

    In this study, the performance of three nano-composite energy storage absorbents; Vermiculite-CaCl2 (SIM-3a), Vermiculite-CaCl2-LiNO3 (SIM-3f), and the desiccant Zeolite 13X were experimentally investigated for suitability to domestic scale thermal energy storage. A novel 3 kWh open thermochemical reactor consisting of new meshed tube air diffusers was built to experimentally examine performance. The results were compared to those obtained using a previously developed flatbed experimental rea...

  19. Interaction of stress and phase transformations during thermochemical surface engineering

    DEFF Research Database (Denmark)

    Jespersen, Freja Nygaard

    and diffusion kinetics to simulate the evolution of composition-depth and stress-depth profiles resulting from nitriding of austenitic stainless steel. The model takes into account a composition-dependent diffusion coefficient of nitrogen in expanded austenite, short range ordering (trapping) of nitrogen atoms...... examined. The effect of pre-stressing the sample was also tested, to investigate the effects of a residual stress-state that might be present from processing of the metal specimen. Controlled thermochemical treatment of austenitic stainless steel was investigated experimentally by in-diffusion of nitrogen...... from a gaseous environment. Measurements of diffusion coefficient were conducted using thermogravimetry....

  20. Experimental study of vortex diffusers

    Energy Technology Data Exchange (ETDEWEB)

    Shakerin, S.; Miller, P.L. [National Renewable Energy Lab., Golden, CO (United States)

    1995-11-01

    This report documents experimental research performed on vortex diffusers used in ventilation and air-conditioning systems. The main objectives of the research were (1) to study the flow characteristics of isothermal jets issuing from vortex diffusers, (2) to compare the vortex diffuser`s performance with that of a conventional diffuser, and (3) to prepare a report that disseminates the results to the designers of ventilation and air-conditioning systems. The researchers considered three diffusers: a conventional round ceiling diffuser and two different styles of vortex diffusers. Overall, the vortex diffusers create slightly more induction of ambient air in comparison to the conventional diffuser.

  1. Experimental and DFT studies of solvent effects on molecular structure and physical properties of Dipyridylamine pyridine based ligand

    Science.gov (United States)

    Bilkan, Mustafa Tuğfan; Şahin, Onur; Yurdakul, Şenay

    2017-04-01

    The solvent effects on molecular structure, electronic, vibrational and thermochemical properties of 2,2‧-Dipyridylamine were investigated by using experimental and theoretical methods. 2,2‧-Dipyridylamine molecule was selected for this study intentionally because it has two pyridyl rings connected by amine bridge. This allows to change the stable equilibrium geometry, even the slightest effects. Dichloromethane was chosen as solvent. The reason for this selection is to examine whether the chlorine atoms make hydrogen bonds with the ligand atoms. For this purpose, firstly 2,2‧-Dipyridylamine solution was prepared and characterized by FT-IR and FT-Raman spectroscopy. Secondly, crystal structure of 2,2‧-Dipyridylamine was obtained to compare with the calculated geometric parameters. The crystal structure was analyzed by Single Crystal X-Ray diffraction methods. Density Functional Theory calculations were conducted with B3LYP functional and 6-31G(d) basis set. The theoretical vibrational properties of optimized geometric structure were computed in vapor and solvation phases. Two different theoretical approaches were discussed, based on the experimental results. It can be seen from the experimental and theoretical studies that the structural, vibrational, thermochemical and electronic properties are dependent on the solvent effects for selected structure. Furthermore, the chlorine atoms of Dichloromethane do not make hydrogen bonds with the ligand atoms.

  2. The Effect of Water Chemistry on Thermochemical Sulfate Reduction: A Case Study from the Ordovician in the Tazhong Area, Northwest China

    Directory of Open Access Journals (Sweden)

    Hongxia Li

    2017-01-01

    Full Text Available Formation water chemistry, sulfate sulfur isotopes, and associated H2S contents and sulfur isotopes were measured from the Ordovician in Tazhong area, Tarim Basin. The aim is to elucidate the effects of geochemical composition of formation water on thermochemical sulfate reduction (TSR and potential usage of SO4/Cl ratios as a new proxy for TSR extents in areas, where H2S and thiaadamantanes (TAs data are not available. The formation water has SO4/Cl ratios from 0.0002 to 0.016, significantly lower than 0.04 to 0.05 from 3 to 7 times evapoconcentrated seawater. Thus, the low values are explained to result from TSR. Furthermore, the SO4/Cl ratios show negative correlation relationships to TAs and H2S concentrations, indicating that TSR occurred in a relatively closed system and SO4/Cl ratio can be used to indicate TSR extents in this area. Extensive TSR in the Cambrian in the Tazhong area, represented by low SO4/Cl ratios and high H2S and TAs concentrations, is accompanied by formation water with high TDS and Mg concentrations, indicating the effects of water chemistry on TSR under a realistic geological background. In contrast, the low TSR extent in the Ordovician may have resulted from limited TSR reaction duration and total contribution of aqueous SO42-.

  3. Biomass Thermochemical Conversion Program. 1983 Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

    1984-08-01

    Highlights of progress achieved in the program of thermochemical conversion of biomass into clean fuels during 1983 are summarized. Gasification research projects include: production of a medium-Btu gas without using purified oxygen at Battelle-Columbus Laboratories; high pressure (up to 500 psia) steam-oxygen gasification of biomass in a fluidized bed reactor at IGT; producing synthesis gas via catalytic gasification at PNL; indirect reactor heating methods at the Univ. of Missouri-Rolla and Texas Tech Univ.; improving the reliability, performance, and acceptability of small air-blown gasifiers at Univ. of Florida-Gainesville, Rocky Creek Farm Gasogens, and Cal Recovery Systems. Liquefaction projects include: determination of individual sequential pyrolysis mechanisms at SERI; research at SERI on a unique entrained, ablative fast pyrolysis reactor for supplying the heat fluxes required for fast pyrolysis; work at BNL on rapid pyrolysis of biomass in an atmosphere of methane to increase the yields of olefin and BTX products; research at the Georgia Inst. of Tech. on an entrained rapid pyrolysis reactor to produce higher yields of pyrolysis oil; research on an advanced concept to liquefy very concentrated biomass slurries in an integrated extruder/static mixer reactor at the Univ. of Arizona; and research at PNL on the characterization and upgrading of direct liquefaction oils including research to lower oxygen content and viscosity of the product. Combustion projects include: research on a directly fired wood combustor/gas turbine system at Aerospace Research Corp.; adaptation of Stirling engine external combustion systems to biomass fuels at United Stirling, Inc.; and theoretical modeling and experimental verification of biomass combustion behavior at JPL to increase biomass combustion efficiency and examine the effects of additives on combustion rates. 26 figures, 1 table.

  4. Experimental study of snow friction

    Science.gov (United States)

    Cohen, Caroline; Canale, Luca; Siria, Alessandro; Quere, David; Bocquet, Lyderic; Clanet, Christophe

    2017-11-01

    Snow friction results from the interplay of different physical processes: solid friction of granular material, phase change and lubrication, heat transport, capillarity, elasticity and plasticity. The multiple conditions of temperature, humidity and density of the snow result in different regimes of friction. In particular, there is an optimal amount of melted water to lubricate the contact between the ski sole and the snow grains. The thickness of the water layer depends on temperature, speed... A huge variety of waxes have been empirically developed to adapt the amount of water to the conditions of skiing, but remain mysterious. In these study, we investigate experimentally the mechanisms of snow friction at different scales: first, the friction of a ski on snow is measured on a test bench, depending on the snow characteristics and for different waxes. Then microscopic experiments are led in order to understand the friction at the ice crystals scale.

  5. Thermochemical storage for CSP via redox structured reactors/heat exchangers: The RESTRUCTURE project

    Science.gov (United States)

    Karagiannakis, George; Pagkoura, Chrysoula; Konstandopoulos, Athanasios G.; Tescari, Stefania; Singh, Abhishek; Roeb, Martin; Lange, Matthias; Marcher, Johnny; Jové, Aleix; Prieto, Cristina; Rattenbury, Michael; Chasiotis, Andreas

    2017-06-01

    The present work provides an overview of activities performed in the framework of the EU-funded collaborative project RESTRUCTURE, the main goal of which was to develop and validate a compact structured reactor/heat exchanger for thermochemical storage driven by 2-step high temperature redox metal oxide cycles. The starting point of development path included redox materials qualification via both theoretical and lab-scale experimental studies. Most favorable compositions were cobalt oxide/alumina composites. Preparation of small-scale structured bodies included various approaches, ranging from perforated pellets to more sophisticated honeycomb geometries, fabricated by extrusion and coating. Proof-of-concept of the proposed novel reactor/heat exchanger was successfully validated in small-scale structures and the next step included scaling up of redox honeycombs production. Significant challenges were identified for the case of extruded full-size bodies and the final qualified approach related to preparation of cordierite substrates coated with cobalt oxide. The successful experimental evaluation of the pilot reactor/heat exchanger system constructed motivated the preliminary techno-economic evaluation of the proposed novel thermochemical energy storage concept. Taking into account experimental results, available technologies and standard design aspects a model for a 70.5 MWe CSP plant was defined. Estimated LCOE costs were calculated to be in the range of reference values for Combined Cycle Power Plants operated by natural gas. One of main cost contributors was the storage system itself, partially due to relatively high cost of cobalt oxide. This highlighted the need to identify less costly and equally efficient to cobalt oxide redox materials.

  6. New applications with time-dependent thermochemical simulation

    Energy Technology Data Exchange (ETDEWEB)

    Koukkari, P. [VTT Chemical Technology, Espoo (Finland); Laukkanen, L. [VTT Automation, Espoo (Finland); Penttilae, K. [Kemira Engineering Oy, Helsinki (Finland)

    1996-12-31

    A new method (RATEMIX) to calculate multicomponent chemical reaction mixtures as a series of sequential thermochemical states was recently introduced. The procedure combines multicomponent thermodynamics with chemical kinetics and may be used to simulate the multicomponent reactors as a thermochemical natural process. The method combines the desired reaction rates sequentially with constrained Gibbs energy minimization. The reactant concentrations are determined by the experimental (Arrhenius) rate laws. During the course of the given reaction the subsequent side reactions are supposed to occur reversibly. At every sequential stage of the given reaction the temperature and composition of the reaction mixture are calculated by a thermodynamic subroutine, which minimizes the Gibbs energy of the system and takes into account the heat transfer between the system and its surroundings. The extents of reaction are included as algorithmic constraints in the Gibbs energy minimization procedure. Initially, the reactants are introduced to the system as inert copies to match both the mass and energy balance of the reactive system. During the calculation the copies are sequentially interchanged to the actual reactants which allows one to simulate the time-dependent reaction route by using the thermochemical procedure. For each intermediate stage, the temperature and composition are calculated and as well numerical estimates of the thermodynamic functions are obtained. The method is applicable in processes where the core thermodynamic and kinetic data of the system are known and the time-dependent heat transfer data can either be measured or estimated by calculation. The method has been used to simulate e.g. high temperature flame reactions, zinc vapour oxidation and a counter-current rotary drum with chemical reactions. The procedure has today been tested with SOLGASMIX, CHEMSAGE and HSC programs. (author)

  7. Thermochemical heat storage - system design issues

    NARCIS (Netherlands)

    Jong, A.J. de; Trausel, F.; Finck, C.J.; Vliet, L.D. van; Cuypers, R.

    2014-01-01

    Thermochemical materials (TCMs) are a promising solution for seasonal heat storage, providing the possibility to store excess solar energy from the warm season for later use during the cold season, and with that all year long sustainable energy. With our fixed bed, vacuum reactors using zeolite as

  8. Some Aspects of Thermochemical Decomposition of Peat

    Directory of Open Access Journals (Sweden)

    Y. A. Losiuk

    2008-01-01

    Full Text Available The paper considers peculiar features of thermochemical decomposition of peat as a result of quick pyrolysis. Evaluation of energy and economic expediency of the preliminary peat decomposition process for obtaining liquid and gaseous products has been made in the paper. The paper reveals prospects pertaining to application of the given technology while generating electric power and heat.

  9. 2009 Thermochemical Conversion Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Thermochemical Conversion platform review meeting, held on April 14-16, 2009, at the Sheraton Denver Downtown, Denver, Colorado.

  10. Biomass for thermochemical conversion: targets and challenges

    Directory of Open Access Journals (Sweden)

    Paul eTanger

    2013-07-01

    Full Text Available Bioenergy will be one component of a suite of alternatives to fossil fuels. Effective conversion of biomass to energy will require the careful pairing of advanced conversion technologies with biomass feedstocks optimized for the purpose. Lignocellulosic biomass can be converted to useful energy products via two distinct pathways: enzymatic or thermochemical conversion. The thermochemical pathways are reviewed and potential biotechnology or breeding targets to improve feedstocks for pyrolysis, gasification, and combustion are identified. Biomass traits influencing the effectiveness of the thermochemical process (cell wall composition, mineral and moisture content differ from those important for enzymatic conversion and so properties are discussed in the language of biologists (biochemical analysis as well as that of engineers (proximate and ultimate analysis. We discuss the genetic control, potential environmental influence, and consequences of modification of these traits. Improving feedstocks for thermochemical conversion can be accomplished by the optimization of lignin levels, and the reduction of ash and moisture content. We suggest that ultimate analysis and associated properties such as H:C, O:C, and heating value might be more amenable than traditional biochemical analysis to the high-throughput necessary for the phenotyping of large plant populations. Expanding our knowledge of these biomass traits will play a critical role in the utilization of biomass for energy production globally, and add to our understanding of how plants tailor their composition with their environment.

  11. High-temperature thermochemical energy storage based on redox reactions using Co-Fe and Mn-Fe mixed metal oxides

    Science.gov (United States)

    André, Laurie; Abanades, Stéphane; Cassayre, Laurent

    2017-09-01

    Metal oxides are potential materials for thermochemical heat storage via reversible endothermal/exothermal redox reactions, and among them, cobalt oxide and manganese oxide are attracting attention. The synthesis of mixed oxides is considered as a way to answer the drawbacks of pure metal oxides, such as slow reaction kinetics, loss-in-capacity over cycles or sintering issues, and the materials potential for thermochemical heat storage application needs to be assessed. This work proposes a study combining thermodynamic calculations and experimental measurements by simultaneous thermogravimetric analysis and calorimetry, in order to identify the impact of iron oxide addition to Co and Mn-based oxides. Fe addition decreased the redox activity and energy storage capacity of Co3O4/CoO, whereas the reaction rate, reversibility and cycling stability of Mn2O3/Mn3O4 was significantly enhanced with added Fe amounts above 15 mol%, and the energy storage capacity was slightly improved. The formation of a reactive cubic spinel explained the improved re-oxidation yield of Mn-based oxides that could be cycled between bixbyite and cubic spinel phases, whereas a low reactive tetragonal spinel phase showing poor re-oxidation was formed below 15 mol% Fe. Thermodynamic equilibrium calculations predict accurately the behavior of both systems. The possibility to identify other suitable mixed oxides becomes conceivable, by enabling the selection of transition metal additives for tuning the redox properties of mixed metal oxides destined for thermochemical energy storage applications.

  12. Numerical modelling of a 100-Wh lab-scale thermochemical heat storage system for concentrating solar power plants

    Science.gov (United States)

    de Miguel, Sandra Álvarez; Bellan, Selvan; de María, J. M. García; González-Aguilar, José; Romero, Manuel

    2016-05-01

    Dispatchable electricity generation on demand is a fundamental issue for commercial deployment of Concentrated Solar Power (CSP) plants. One of the promising routes to overcome the intermittence of the solar resource is the use of thermochemical energy storage systems based on redox reactions of metal oxides. Different metal oxides might potential candidates as storing material depending on the foreseen working temperature range. In the framework of the FP7 European project TCSPower, a particle-based reactor is used to analyze this type of materials. The lab-scale thermochemical reactor is initially tested using an inert material (alumina particles) instead of reactants in order to study its thermal performance. Thermocouples installed inside the system at various positions monitor the experiments. A three dimensional numerical model is developed to investigate the flow and heat transfer in the reactor. The governing equations - mass, momentum and energy conservation - are solved by the finite element method in the commercial software COMSOL Multiphysics. Simulations are performed for the experimental conditions. Experimentally measured and numerically predicted temperature profiles at various locations inside the system are compared and presented in this paper.

  13. Experimental Infrasound Studies in Nevada

    Science.gov (United States)

    Herrin, E. T.; Negraru, P. T.; Golden, P.; Williams, A.

    2009-12-01

    An experimental propagation study was carried out in Nevada in June 2009 on Julian days 173-177. During this field experiment we deployed 16 single channel digital infrasound recorders to monitor the munitions disposal activities near Hawthorne, NV. The sensors were deployed in a single line and placed approximately 12 km apart at distances ranging from 2 to 177 km. A four element semi-permanent infrasound array named FNIAR was installed approximately 154 km north of the detonation site in line with the individual temporary recorders. Tropospheric arrivals were observed during all days of the experiment, but during day 176 the observed arrivals had very large amplitudes. A large signal was observed at 58 km from the detonation site with amplitude as large as 4 Pascals, while at 94 km no signal was observed. At FNIAR the amplitude of the tropospheric arrival was 1 Pascal. During this day meteorological data acquired in the propagation path showed a strong jet stream to the north. On day 177 we were not able to identify tropospheric arrivals beyond 34 km, but at stations beyond 152 km we observed stratospheric arrivals. Continuous monitoring of these signals at FNIAR shows that stratospheric arrivals are the most numerous. In a two month period, from 06/15/2009 to 08/15/2009 there were 35 operational days at the Hawthorne disposal facility resulting in 212 explosions with known origin times. Based on the celerity values there were 115 explosions that have only stratospheric arrivals (celerities of 300-275 m/s), 72 explosions with both tropospheric (celerities above 330 m/s) and stratospheric arrivals, 20 explosions that were not detected and five explosions that have only tropospheric arrivals.

  14. EXPERIMENTAL STUDY IN NATURAL CONVECTION

    African Journals Online (AJOL)

    PROF. BARTH EKWEME

    climatic conditions are favorable for the development of solar chimneys for the production of electrical energy or the drying of agro-food products. 1.1 Experimental models. The first prototype tower was built in Manzanares in. 1981, thanks to the team of Professor Schlaich, Haaf et al., (1983); Haaf et al., (1984), in Spain.

  15. Thermochemical valorization and characterization of household biowaste.

    Science.gov (United States)

    Vakalis, S; Sotiropoulos, A; Moustakas, K; Malamis, D; Vekkos, K; Baratieri, M

    2017-12-01

    Valorization of municipal solid waste (MSW), by means of energy and material recovery, is considered to be a crucial step for sustainable waste management. A significant fraction of MSW is comprised from food waste, the treatment of which is still a challenge. Therefore, the conventional disposal of food waste in landfills is being gradually replaced by recycling aerobic treatment, anaerobic digestion and waste-to-energy. In principle, thermal processes like combustion and gasification are preferred for the recovery of energy due to the higher electrical efficiency and the significantly less time required for the process to be completed when compared to biological process, i.e. composting, anaerobic digestion and transesterification. Nonetheless, the high water content and the molecular structure of biowaste are constraining factors in regard to the application of thermal conversion pathways. Investigating alternative solutions for the pre-treatment and more energy efficient handling of this waste fraction may provide pathways for the optimization of the whole process. In this study, by means of utilizing drying/milling as an intermediate step, thermal treatment of household biowaste has become possible. Household biowaste has been thermally processed in a bench scale reactor by means of torrefaction, carbonization and high temperature pyrolysis. According to the operational conditions, fluctuating fractions of biochar, bio-oil (tar) and syngas were recovered. The thermochemical properties of the feedstock and products were analyzed by means of Simultaneous Thermal Analysis (STA), Ultimate and Proximate analysis and Attenuated Total Reflectance (ATR). The analysis of the products shows that torrefaction of dried household biowaste produces an energy dense fuel and high temperature pyrolysis produces a graphite-like material with relatively high yield. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Preliminary experimental results of barium chloride-ammonia reaction for using in a solar thermochemical cooling cycle; Resultados experimentales preliminares de la reaccion entre el cloruro de bario y el amoniaco para su utilizacion en un ciclo de refrigeracion solar termoquimico

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, C. O. B.; Mendez, E. R.; Pilatowsky, L. F.; Rivera, W. G.

    2004-07-01

    An experimental intermittent thermochemical refrigeration system operating with barium chloride-ammonia reaction is described. The barium chloride is used as absorbent and ammonia as refrigerant. The equipment components and the experimental preliminary results are also presented. The temperature range of the thermal fluid from 70 C to 95 C was established. The main results showed that the generation temperature oscillated from 53 C to 56 C for a condensation temperature of 23 C. The generation pressure range was from 10 to 11 bar. In the evaporating-absorption process, the evaporating temperature range was between 10 C and 0 C for a saturation pressure of 2.4 bar. The results showed also, the technical feasibility to operate this refrigeration system with low cost solar flat plate collectors in remote areas. (Author) CIEMAT (Centro de Investigaciones Energeticas, Mediambientales y Tecnologicas). The LCA is an environmental management methodology with which the environmental impacts associate to a system, process product are detected. The ISO standard 14040: 1997 contain the procedure to follow. life cycle of the plant is divided in 4 stages: extraction and transformation of raw materials; transport and installation; completion of the system to operate like a steam generator maintenance, and dismantling. As result, some improvements are recommended, mainly related to changes in the types of materials and the treatment of the emissions. (Author)

  17. A web service infrastructure for thermochemical data.

    Science.gov (United States)

    Paolini, Christopher P; Bhattacharjee, Subrata

    2008-07-01

    W3C standardized Web Services are becoming an increasingly popular middleware technology used to facilitate the open exchange of chemical data. While several projects in existence use Web Services to wrap existing commercial and open-source tools that mine chemical structure data, no Web Service infrastructure has yet been developed to compute thermochemical properties of substances. This work presents an infrastructure of Web Services for thermochemical data retrieval. Several examples are presented to demonstrate how our Web Services can be called from Java, through JavaScript using an AJAX methodology, and within commonly used commercial applications such as Microsoft Excel and MATLAB for use in computational work. We illustrate how a JANAF table, widely used by chemists and engineers, can be quickly reproduced through our Web Service infrastructure.

  18. THERMOCHEMICAL CONVERSION BEHAVIOUR OF DIFFERENT BIOMASS FEEDSTOCKS: PYROLYSIS AND GASIFICATION

    Directory of Open Access Journals (Sweden)

    Işıl Gülsaç

    2016-11-01

    Full Text Available n this study, a bench-scale bubbling fluidized bed (BFB gasifier and thermogravimetric analyzer (TGA were applied for the determination of the thermochemical conversion reactivity of biomass fuels under both gasification and pyrolysis conditions. Six different biomass feedstocks, namely; straw pellet (SP, softwood pellet (WP, torrefied wood chips (TWC, pyrolysis char (PC, miled sunflower seed (MSS and dried distillers’ grains and solubles (DDGS were investigated. TGA of biomass feedstocks were carried out under pyrolysis conditions at four different heating rates (2-15 °C/min. Raw data obtained from the experiments were used to calculate the kinetic parameters (A, Ea of the samples by using two different models; Coats-Redfern and Isoconversional Method. TGA analysis showed that pyrolysis char was the only sample having decomposition temperature above 800 K since it was the pre-pyrolized sample before the gasification. According to DTG profiles, two peaks and two shoulders at around 450-650 K were observed for DDGS whereas no peaks were detected for pyrolysis char as the indication of absence of volatiles/cellulosic components. It was seen that the highest devolatization rates and devolatization temperatures (associated mainly with cellulose decomposition were obtained for softwood and torrefied wood samples, which had the least char yields among the other biomass feedstocks. It was seen that WP was more reactive for thermochemical conversion and less prone to agglomeration. Furthermore high ash content and agglomeration index of MSS were the potential drawbacks in front of its utilization via thermochemical conversion. During the air gasification of these feedstocks (except DDGS, the product syngas was characterized in terms of main gas composition, tar and sulfur compounds. It was shown that the highest cold gas efficiency, carbon conversion and calorific value were obtained for the gasification of SP. On the other hand, SP had some

  19. Computational Modeling of Thermochemical Evolution of Aluminum Smelter Crust

    Science.gov (United States)

    Zhang, Qinsong; Taylor, Mark P.; Chen, John J. J.

    2015-02-01

    In an aluminum reduction cell, crushed anode cover at room temperature is added onto the exposed bulk electrolyte surface around newly positioned anodes and is heated by high heat flux from this liquid electrolyte. Liquid electrolyte penetrates inside the porous anode cover. Solid cryolite and alumina crystallize from the liquid electrolyte due to the temperature gradient in the anode cover. A solidified crust forms at the bottom part of the anode cover during the heating up period. A thermochemical model which takes into account both the liquid electrolyte penetration and phase transformations has been developed to simulate the temperature evolution, chemical composition development, and liquid front penetration and content in the anode cover. The model is tested against experimental data obtained from industrial cells and laboratory experiments in this paper.

  20. Benchmark Thermochemistry for Biologically Relevant Adenine and Cytosine. A Combined Experimental and Theoretical Study.

    Science.gov (United States)

    Emel'yanenko, Vladimir N; Zaitsau, Dzmitry H; Shoifet, Evgeni; Meurer, Florian; Verevkin, Sergey P; Schick, Christoph; Held, Christoph

    2015-09-17

    The thermochemical properties available in the literature for adenine and cytosine are in disarray. A new condensed phase standard (p° = 0.1 MPa) molar enthalpy of formation at T = 298.15 K was measured by using combustion calorimetry. New molar enthalpies of sublimation were derived from the temperature dependence of vapor pressure measured by transpiration and by the quarz-crystal microbalance technique. The heat capacities of crystalline adenine and cytosine were measured by temperature-modulated DSC. Thermodynamic data on adenine and cytosine available in the literature were collected, evaluated, and combined with our experimental results. Thus, the evaluated collection of data together with the new experimental results reported here has helped to resolve contradictions in the available enthalpies of formation. A set of reliable thermochemical data is recommended for adenine and cytosine for further thermochemical calculations. Quantum-chemical calculations of the gas phase molar enthalpies of formation of adenine and cytosine have been performed by using the G4 method and results were in excellent agreement with the recommended experimental data. The standard molar entropies of formation and the standard molar Gibbs functions of formation in crystal and gas state have been calculated. Experimental vapor-pressure data measured in this work were used to estimate pure-component PC-SAFT parameters. This allowed modeling solubility of adenine and cytosine in water over the temperature interval 278-310 K.

  1. Experimental study of potential neutron moderator materials

    Science.gov (United States)

    Mocko, M.; Daemen, L. L.; Hartl, M. A.; Huegle, Th.; Muhrer, G.

    2010-12-01

    We present an experimental investigation of thermal neutron energy spectra produced by lead and bismuth hydroxides (Pb(OH) 2, and Bi(OH) 3). The experimental energy spectra are compared with a thermal neutron energy spectrum produced by water measured in the same geometry. We developed an MCNPX geometry model designed to help with the interpretation of the experimental data. We demonstrate a very good reproduction of the experimental thermal neutron energy spectrum produced by the water moderator in our tightly coupled geometry. We study our experimental results for Pb(OH) 2 and Bi(OH) 3 using thermal neutron scattering kernels for hydrogen, bismuth, and lead.

  2. Kinetics of Thermochemical Reactions Important in the Venus Atmospheric Sulfur Cycle

    Science.gov (United States)

    Fegley, Bruce, Jr.

    1997-01-01

    The purpose of this project was to experimentally measure the rates of several thermochemical gas-solid reactions between sulfur gases in the Venus atmosphere and reactive minerals on the hot Venus surface. Despite the great importance of these reactions for the maintenance of significant amounts of sulfur gases (and thus for the maintenance of the global cloud cover) in the atmosphere of Venus, essentially no kinetic data are currently available for them.

  3. Experimental studies of neutrino oscillations

    CERN Document Server

    Kajita, Takaaki

    2016-01-01

    The 2015 Nobel Prize in physics has been awarded to Takaaki Kajita and Arthur McDonald "for the discovery of neutrino oscillations, which shows that neutrinos have mass". Takaaki Kajita of Tokyo University is a Japanese physicist, known for neutrino experiments at the Kamiokande and its successor, Super-Kamiokande. This volume of collected works of Kajita on neutrino oscillations provides a good glimpse into as well as a record of the rise and the role of Asian research in the frontiers of neutrino physics. Japan is now a major force in the study of the 3 families of neutrinos. Much remains to be done to clarify the Dirac vs. Majorana nature of the neutrino, and the cosmological implications of the neutrino. The collected works of Kajita and his Super-Kamiokande group will leave an indelible foot-print in the history of big and better science.

  4. Thermo-chemical simultion of a composite offshore vertical axis wind turbine blade

    NARCIS (Netherlands)

    Baran, Ismet; Tutum, Cem Celal; Hattel, Jesper Henri

    2012-01-01

    In the present study three dimensional steady state thermo-chemical simulation of a pultrusion process is investigated by using the finite element/nodal control volume (FE/NCV) technique. Pultrusion simulation of a composite having a C-shaped cross section is performed as a validation case. The

  5. Improving Students' Chemical Literacy Levels on Thermochemical and Thermodynamics Concepts through a Context-Based Approach

    Science.gov (United States)

    Cigdemoglu, Ceyhan; Geban, Omer

    2015-01-01

    The aim of this study was to delve into the effect of context-based approach (CBA) over traditional instruction (TI) on students' chemical literacy level related to thermochemical and thermodynamics concepts. Four eleventh-grade classes with 118 students in total taught by two teachers from a public high school in 2012 fall semester were enrolled…

  6. CREATIVE DISCLOSURE: AN EXPERIMENTAL STUDY

    Directory of Open Access Journals (Sweden)

    Cuzdriorean Dan Dacian

    2012-07-01

    Full Text Available This empirical study extends the study conducted by Vladu, Grosanu and Cuzdriorean (2012 and reached similar conclusions. This particular research was conducted with the scope of assessing the impact of: positive bias, persuasive language, creative visual manipulation and performance comparisons over the unsophisticated users of accounting opinion. We have chosen this particular category since retail investors have been identified as relying on the information provided in corporate annual reports for decision making (Wills, 2008. Based on their relative inexperience and limited knowledge of these investors it is plausible that they can be mislead easily comparing to more sophisticated users of accounting information, as financial analysts. The main argument for conducting such a research is the fact that little research was conducted so far and the effects of creative disclosure on investment decision cannot be assessed so far. Based on this, we conducted a laboratory experiment where participants where provided with an informational set of financial data and required to make an investment decision. Our results document that the users perceptions is strongly affected by creative disclosure, contradictory with previous results documented in the literature, that their opinion cannot be influenced since they relay mostly on numerical information and less on the narrative segments of the financial statements. Even if our sample compressed few participants, we consider the results conclusive. A further research can extend the sample and test if our research hypothesis can be validated. Another possible spring of research can deal with the assessing of the opinion of the users of accounting information that are not considered unsophisticated, as financial analysts.

  7. Screening analysis of solar thermochemical hydrogen concepts.

    Energy Technology Data Exchange (ETDEWEB)

    Diver, Richard B., Jr.; Kolb, Gregory J.

    2008-03-01

    A screening analysis was performed to identify concentrating solar power (CSP) concepts that produce hydrogen with the highest efficiency. Several CSP concepts were identified that have the potential to be much more efficient than today's low-temperature electrolysis technology. They combine a central receiver or dish with either a thermochemical cycle or high-temperature electrolyzer that operate at temperatures >600 C. The solar-to-hydrogen efficiencies of the best central receiver concepts exceed 20%, significantly better than the 14% value predicted for low-temperature electrolysis.

  8. The application of vacuum heat and thermo-chemical treatment to improve strength of different heavily loaded machine parts and engineering instruments

    Directory of Open Access Journals (Sweden)

    A. E. Smirnov

    2014-01-01

    Full Text Available The paper was analyzes an application of vacuum equipment for heat and thermo-chemical treatment of aviation gear wheals, small bearings for aircraft equipment parts, and high strength stamps.The generalization of designed vacuum technologies of heat and thermo-chemical treatment results compared with traditional processes is accepted as objective of the paper.The practical use of vacuum processes (low pressure ones has been first discussed in the specific context of the problem solution to design hardening technologies for critical parts from complex alloyed steels with exclusive operational properties. To solve this problem by traditional methods is impossible.The research techniques included the complex combination of experimental studies conducted using an industrial universal vacuum furnace of SECO/WARWICK S.A. company (Poland, and of metallographic exams and mechanic tests as well as of numerical simulations accomplished by original vacuum carburizing (nitrocarburizing models.The study objects were as follows:a steels containing chromium, nickel, molybdenum, tungsten and vanadium, which were used for gear wheals. In particular, a precipitation-hardening steel 13Kh3N3M2VFB was for the first time applied at carburized (nitrocarburized condition;b Steel 8Kh4V9F2, which was used for bearing rings;c Steel Kh12MF, which was used for stamps.The following operation properties are critical for gears: high contact fatigue endurance on the pitch circle; high bending fatigue endurance on the gears tooth-root; wear resistance on entire surface. Designing the technological operating conditions is complicated due to need to combine high values of all these properties, which stipulate the little-compatible requirements for physical and phase composition of the diffusion layers. Due to the advantages of thermo-chemical vacuum processes in oxygen-free atmosphere, namely technological flexibility and high reproducibility, the aperiodic cycles of

  9. Experimental and kinetic modeling study of 3-methylheptane in a jet-stirred reactor

    KAUST Repository

    Karsenty, Florent

    2012-08-16

    Improving the combustion of conventional and alternative fuels in practical applications requires the fundamental understanding of large hydrocarbon combustion chemistry. The focus of the present study is on a high-molecular-weight branched alkane, namely, 3-methylheptane, oxidized in a jet-stirred reactor. This fuel, along with 2-methylheptane, 2,5-dimethylhexane, and n-octane, are candidate surrogate components for conventional diesel fuels derived from petroleum, synthetic Fischer-Tropsch diesel and jet fuels derived from coal, natural gas, and/or biomass, and renewable diesel and jet fuels derived from the thermochemical treatment of bioderived fats and oils. This study presents new experimental results along with a low- and high-temperature chemical kinetic model for the oxidation of 3-methylheptane. The proposed model is validated against these new experimental data from a jet-stirred reactor operated at 10 atm, over the temperature range of 530-1220 K, and for equivalence ratios of 0.5, 1, and 2. Significant effort is placed on the understanding of the effects of methyl substitution on important combustion properties, such as fuel reactivity and species formation. It was found that 3-methylheptane reacts more slowly than 2-methylheptane at both low and high temperatures in the jet-stirred reactor. © 2012 American Chemical Society.

  10. TEA: A CODE CALCULATING THERMOCHEMICAL EQUILIBRIUM ABUNDANCES

    Energy Technology Data Exchange (ETDEWEB)

    Blecic, Jasmina; Harrington, Joseph; Bowman, M. Oliver, E-mail: jasmina@physics.ucf.edu [Planetary Sciences Group, Department of Physics, University of Central Florida, Orlando, FL 32816-2385 (United States)

    2016-07-01

    We present an open-source Thermochemical Equilibrium Abundances (TEA) code that calculates the abundances of gaseous molecular species. The code is based on the methodology of White et al. and Eriksson. It applies Gibbs free-energy minimization using an iterative, Lagrangian optimization scheme. Given elemental abundances, TEA calculates molecular abundances for a particular temperature and pressure or a list of temperature–pressure pairs. We tested the code against the method of Burrows and Sharp, the free thermochemical equilibrium code Chemical Equilibrium with Applications (CEA), and the example given by Burrows and Sharp. Using their thermodynamic data, TEA reproduces their final abundances, but with higher precision. We also applied the TEA abundance calculations to models of several hot-Jupiter exoplanets, producing expected results. TEA is written in Python in a modular format. There is a start guide, a user manual, and a code document in addition to this theory paper. TEA is available under a reproducible-research, open-source license via https://github.com/dzesmin/TEA.

  11. CHEETAH: A next generation thermochemical code

    Energy Technology Data Exchange (ETDEWEB)

    Fried, L.; Souers, P.

    1994-11-01

    CHEETAH is an effort to bring the TIGER thermochemical code into the 1990s. A wide variety of improvements have been made in Version 1.0. We have improved the robustness and ease of use of TIGER. All of TIGER`s solvers have been replaced by new algorithms. We find that CHEETAH solves a wider variety of problems with no user intervention (e.g. no guesses for the C-J state) than TIGER did. CHEETAH has been made simpler to use than TIGER; typical use of the code occurs with the new standard run command. CHEETAH will make the use of thermochemical codes more attractive to practical explosive formulators. We have also made an extensive effort to improve over the results of TIGER. CHEETAH`s version of the BKW equation of state (BKWC) is able to accurately reproduce energies from cylinder tests; something that other BKW parameter sets have been unable to do. Calculations performed with BKWC execute very quickly; typical run times are under 10 seconds on a workstation. In the future we plan to improve the underlying science in CHEETAH. More accurate equations of state will be used in the gas and the condensed phase. A kinetics capability will be added to the code that will predict reaction zone thickness. Further ease of use features will eventually be added; an automatic formulator that adjusts concentrations to match desired properties is planned.

  12. Thermodynamic properties of isomeric iso-butoxybenzoic acids: Experimental and theoretical study

    Energy Technology Data Exchange (ETDEWEB)

    Jakubczyk, Michał; Sporzyński, Andrzej [Faculty of Chemistry, Warsaw University of Technology, 00-664 Warszawa (Poland); Emel’yanenko, Vladimir N.; Varfolomeev, Mikhail A. [Department of Physical Chemistry, Kazan Federal University, 420008 Kazan (Russian Federation); Verevkin, Sergey P., E-mail: sergey.verevkin@uni-rostock.de [Department of Physical Chemistry, Kazan Federal University, 420008 Kazan (Russian Federation); Department of Physical Chemistry and Department, Science and Technology of Life, Light and Matter, University of Rostock, D-18059 Rostock (Germany)

    2015-09-10

    Highlights: • Vapor pressures of butoxy benzoic acid derivatives were measured. • Vaporization, sublimation and fusion enthalpies were derived. • Molar enthalpies of formation were measured by calorimetry. • Thermochemical data tested for consistency using additivity rules and computations. • Simple additivity method suggested for prediction thermochemical properties. - Abstract: Standard (p° = 0.1 MPa) molar enthalpies of formation at the temperature T = 298.15 K of the 2-, 3-, and 4-iso-butoxybenzoic acids were measured using the combustion calorimetry. Standard molar enthalpies of vaporization and sublimation were derived from the vapor pressure temperature dependencies measured by the transpiration method. Molar enthalpies of the solid state phase transitions were measured by the DSC. Thermodynamic data on alkoxy substituted benzoic acids available in the literature were collected and combined with own experimental results. This data set on alkoxybenzoic acids was evaluated by using quantum-chemical and group-additivity methods.

  13. Experimental Studies on the Hypolipidemic and Haematological ...

    African Journals Online (AJOL)

    Uche

    2011-01-14

    Jan 14, 2011 ... Experimental Studies on the Hypolipidemic and. Haematological Properties of Aqueous ... lipid and haematological profile of serum and blood samples collected were determined respectively. Results: Treatment with simvastatin (10 ..... pathway for cholesterol homeostasis. Science. (Washington, DC) 1986 ...

  14. Solar Thermochemical Hydrogen Production Research (STCH)

    Energy Technology Data Exchange (ETDEWEB)

    Perret, Robert [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2011-05-01

    Eight cycles in a coordinated set of projects for Solar Thermochemical Cycles for Hydrogen production (STCH) were self-evaluated for the DOE-EERE Fuel Cell Technologies Program at a Working Group Meeting on October 8 and 9, 2008. This document reports the initial selection process for development investment in STCH projects, the evaluation process meant to reduce the number of projects as a means to focus resources on development of a few most-likely-to-succeed efforts, the obstacles encountered in project inventory reduction and the outcomes of the evaluation process. Summary technical status of the projects under evaluation is reported and recommendations identified to improve future project planning and selection activities.

  15. EXPERIMENTAL STUDY OF THE PRODUCTION OF SOLAR ...

    African Journals Online (AJOL)

    2010-06-30

    Jun 30, 2010 ... could supply enough hydrogen to operate a fuel cell vehicle. In our study [23] an experimental study is done in the Center of Development of the Renewable Energy,. Algiers, Algeria; hydrogen is produced using a Proton Exchange Membrane (PEM) electrolyser supplied by PV panel; when an electric ...

  16. 2011 Biomass Program Platform Peer Review. Thermochemical Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Grabowski, Paul E. [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Thermochemical Conversion Platform Review meeting.

  17. Collision induced dissociation study of azobenzene and its derivatives: computational and experimental results

    Science.gov (United States)

    Rezaee, Mohammadreza; Compton, Robert

    2015-03-01

    Experimental and computational investigation have been performed in order to study the bond dissociation energy of azobenzene and its derivatives using collision induced dissociation method as well as other energy and structural characteristics. The results have been verified by comparing with results obtained from computational quantum chemistry. We used different density functional methods as well as the Möller-Plesset perturbation theory and the coupled cluster methods to explore geometric, electronic and the spectral properties of the sample molecules. Geometries were calculated and optimized using the 6-311 + + G(2d,2p) basis set and the B3LYP level of theory and these optimized structures have been subjected to the frequency calculations to obtain thermochemical properties by means of different density functional, Möller-Plesset, and coupled cluster theories to obtain a high accuracy estimation of the bond dissociation energy value. The results from experiments and the results obtained from computational thermochemistry are in close agreement. Physics and Astronomy Department

  18. Initial Screening of Thermochemical Water-Splitting Cycles for High Efficiency Generation of Hydrogen Fuels Using Nuclear Power

    Energy Technology Data Exchange (ETDEWEB)

    Brown, L.C.; Funk, J.F.; Showalter, S.K.

    1999-12-15

    OAK B188 Initial Screening of Thermochemical Water-Splitting Cycles for High Efficiency Generation of Hydrogen Fuels Using Nuclear Power There is currently no large scale, cost-effective, environmentally attractive hydrogen production process, nor is such a process available for commercialization. Hydrogen is a promising energy carrier, which potentially could replace the fossil fuels used in the transportation sector of our economy. Fossil fuels are polluting and carbon dioxide emissions from their combustion are thought to be responsible for global warming. The purpose of this work is to determine the potential for efficient, cost-effective, large-scale production of hydrogen utilizing high temperature heat from an advanced nuclear power station. Almost 800 literature references were located which pertain to thermochemical production of hydrogen from water and over 100 thermochemical watersplitting cycles were examined. Using defined criteria and quantifiable metrics, 25 cycles have been selected for more detailed study.

  19. Chemical characterization of sulphur-iodine thermochemical cycle flowstreams by Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Liberatore, Raffaele; Falconieri, Mauro; Lanchi, Michela; Spadoni, Annarita [ENEA CR, Casaccia (Italy)

    2010-07-01

    The Sulphur-Iodine (S-I) thermochemical cycle for hydrogen production from water is one of the widest investigated cycles in the world. Considered the complexity of the S-I process scheme, the focus on chemical characterization of the flowstreams in the loop plant is crucial in order to fully understand chemical equilibriums involved at varying hydriodic acid: (HI:I{sub 2}) ratio in the mixtures and to determine HI and I{sub 2} contents as well. Raman spectroscopy has been widely used to investigate iodine solutions, however few works deals with I{sub 2} in HI aqueous mixtures. The aim of the present study is to use Raman spectroscopy for a rapid qualitative and quantitative characterization of the HI-H{sub 2}O-I{sub 2} mixtures involved in the S-I process. At this purpose, Raman spectra of solutions with known HI and I{sub 2} concentration have been recorded at varying I{sub 2} and HI compositions. It has been found that the chemistry of these solutions is highly dependant on HI:I{sub 2} molar ratio. For ratio up to 1:1, the dominant iodine compounds are I{sub 3}{sup -} and its corresponding ion pair HI{sub 3}. At higher values, close to those of the hydriodic phase HIx of the Bunsen reaction, there is experimental evidence of the formation of higher polyiodine and polyiodides compounds. (orig.)

  20. Laparoscopic ureterocalicostomy in pigs - experimental study

    OpenAIRE

    Caldas, Paulo Fernando de Oliveira; Rocha, Luiz Carlos de Almeida; Oliveira, Marília Teresa de; Ataíde, Michelli Westphal de; Spagnolo, Julio David; Feranti, João Pedro Scussel; Souza, Fernando Wiecheteck de; Silva, Marco Augusto Machado; Brun, Maurício Veloso

    2015-01-01

    This study aimed to evaluated laparoscopic ureterocalicostomy as treatment of experimental ureteropelvic junction (UPJ) obstruction in pigs. Ten male Large White pigs weighting approximately 28.4 (±1.43) kg were used in the current study. The UPJ obstruction was created laparoscopically by double-clipping of the left ureter. After 14 days the animals underwent laparoscopic ureterocalicostomy f The animals were sacrificed for subsequent retrograde pyelography in order to assess the anastomotic...

  1. THERMOCHEMICAL HEAT STORAGE FOR CONCENTRATED SOLAR POWER

    Energy Technology Data Exchange (ETDEWEB)

    PROJECT STAFF

    2011-10-31

    Thermal energy storage (TES) is an integral part of a concentrated solar power (CSP) system. It enables plant operators to generate electricity beyond on sun hours and supply power to the grid to meet peak demand. Current CSP sensible heat storage systems employ molten salts as both the heat transfer fluid and the heat storage media. These systems have an upper operating temperature limit of around 400 C. Future TES systems are expected to operate at temperatures between 600 C to 1000 C for higher thermal efficiencies which should result in lower electricity cost. To meet future operating temperature and electricity cost requirements, a TES concept utilizing thermochemical cycles (TCs) based on multivalent solid oxides was proposed. The system employs a pair of reduction and oxidation (REDOX) reactions to store and release heat. In the storage step, hot air from the solar receiver is used to reduce the oxidation state of an oxide cation, e.g. Fe3+ to Fe2+. Heat energy is thus stored as chemical bonds and the oxide is charged. To discharge the stored energy, the reduced oxide is re-oxidized in air and heat is released. Air is used as both the heat transfer fluid and reactant and no storage of fluid is needed. This project investigated the engineering and economic feasibility of this proposed TES concept. The DOE storage cost and LCOE targets are $15/kWh and $0.09/kWh respectively. Sixteen pure oxide cycles were identified through thermodynamic calculations and literature information. Data showed the kinetics of re-oxidation of the various oxides to be a key barrier to implementing the proposed concept. A down selection was carried out based on operating temperature, materials costs and preliminary laboratory measurements. Cobalt oxide, manganese oxide and barium oxide were selected for developmental studies to improve their REDOX reaction kinetics. A novel approach utilizing mixed oxides to improve the REDOX kinetics of the selected oxides was proposed. It partially

  2. Experimental and computational study of thaumasite structure

    Energy Technology Data Exchange (ETDEWEB)

    Scholtzová, Eva, E-mail: Eva.Scholtzova@savba.sk [Institute of Inorganic Chemistry, Slovak Academy of Sciences, Dúbravská cesta 9, 845 36 Bratislava (Slovakia); Kucková, Lenka; Kožíšek, Jozef [Department of Physical Chemistry, Institute of Physical Chemistry and Chemical Physics, Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Radlinského 9, 812 37 Bratislava (Slovakia); Pálková, Helena [Institute of Inorganic Chemistry, Slovak Academy of Sciences, Dúbravská cesta 9, 845 36 Bratislava (Slovakia); Tunega, Daniel [Institute of Inorganic Chemistry, Slovak Academy of Sciences, Dúbravská cesta 9, 845 36 Bratislava (Slovakia); Institute for Soil Science, University of Natural Resources and Life Sciences, Peter-Jordanstrasse 82, A-1190 Wien (Austria)

    2014-05-01

    The structure of thaumasite has been studied experimentally by means of a single crystal X-ray diffraction and FTIR methods, and theoretically using density functional theory (DFT) method. Very good agreement was achieved between calculated and experimental structural parameters. In addition, calculations offered the refinement of the positions of the hydrogen atoms. The detailed analysis of the hydrogen bonds existing in the thaumasite structure has been performed. Several types of hydrogen bonds have been classified. The water molecules coordinating Ca{sup 2+} cation act as proton donors in moderate O-H···O hydrogen bonds formed with CO₃⁻²and SO₄⁻² anions. The multiple O-H···O hydrogen bonds exist among water molecules themselves. Finally, relatively weak hydrogen bonds form water molecules with the OH groups from the coordination sphere of the Si(OH)₆⁻² anion. Further, calculated vibrational spectrum allowed complete assignment of all vibrational modes which are not available from the experimental spectrum that has a complex structure with overlapped bands, especially below 1500 cm⁻¹. Highlights: • The thaumasite structure was studied experimentally and using DFT method. • We used DFT method for the refinement of the positions of hydrogen atoms. • A detailed analysis of the hydrogen bonds was done. • A complete assignment of all bands to particular types of vibrations was done.

  3. Testing of an advanced thermochemical conversion reactor system

    Energy Technology Data Exchange (ETDEWEB)

    1990-01-01

    This report presents the results of work conducted by MTCI to verify and confirm experimentally the ability of the MTCI gasification process to effectively generate a high-quality, medium-Btu gas from a wider variety of feedstock and waste than that attainable in air-blown, direct gasification systems. The system's overall simplicity, due to the compact nature of the pulse combustor, and the high heat transfer rates attainable within the pulsating flow resonance tubes, provide a decided and near-term potential economic advantage for the MTCI indirect gasification system. The primary objective of this project was the design, construction, and testing of a Process Design Verification System for an indirectly heated, thermochemical fluid-bed reactor and a pulse combustor an an integrated system that can process alternative renewable sources of energy such as biomass, black liquor, municipal solid waste and waste hydrocarbons, including heavy oils into a useful product gas. The test objectives for the biomass portion of this program were to establish definitive performance data on biomass feedstocks covering a wide range of feedstock qualities and characteristics. The test objectives for the black liquor portion of this program were to verify the operation of the indirect gasifier on commercial black liquor containing 65 percent solids at several temperature levels and to characterize the bed carbon content, bed solids particle size and sulfur distribution as a function of gasification conditions. 6 refs., 59 figs., 29 tabs.

  4. Experimental Study on Permeability of Concrete

    Science.gov (United States)

    Yang, Honglu; Liu, Rentai; Zheng, Zhuo; Liu, Haojie; Gao, Yan; Liu, Yankai

    2018-01-01

    To study the influencing factors on permeability of pervious concrete, by adding inorganic organic composite materials obtained experimental results show that different aggregate size, aggregate cement ratio of different, different water cement ratio on the permeability performance. The permeability of the concrete was tested by using the self - made permeable device. The experimental results showed that the permeation coefficient of the experiment was obtained and the factors influencing the permeability of the concrete were compared and analyzed. At the same time, the porosity of pervious concrete was measured, the influence of various variables on porosity was studied, and the influence of various factors on the permeability of voids was found. Finally, through comprehensive analysis of a variety of factors, the optimal water cement ratio is 0.28. At this time, the pervious performance of concrete is optimal.

  5. Experimental studies on transitional separated boundary layers

    OpenAIRE

    Serna Serrano, José

    2013-01-01

    Separated transitional boundary layers appear on key aeronautical processes such as the flow around wings or turbomachinery blades. The aim of this thesis is the study of these flows in representative scenarios of technological applications, gaining knowledge about phenomenology and physical processes that occur there and, developing a simple model for scaling them. To achieve this goal, experimental measurements have been carried out in a low speed facility, ensuring the flow homogeneity and...

  6. An experimental study on the thermal valorization of municipal and animal wastes

    Energy Technology Data Exchange (ETDEWEB)

    Vamvuka, Despina; Sfakiotakis, Stelios [Department of Mineral Resources Engineering, Technical University of Crete, Crete (Greece); Panopoulos, Kyriakos D. [Centre for Research and Technology Hellas / Institute for Solid Fuels Technology and Applications (CERTH/ISFTA), 4th klm. Nat. Rd. Ptolemais-Kozani-P.O. box 95 – GR 50200 Ptolemais (Greece)

    2013-07-01

    Poultry wastes and refused derived fuel disposal through thermochemical processes, such as combustion, has been proposed. These fuels have calorific values that in many cases exceed 20MJ kg-1. An extensive analysis has been performed of pyrolysis and combustion results obtained by thermal analysis measurements. The weight loss data were recorded continuously, under dynamic conditions, in the range 25-1300 deg C. A first order parallel reactions model and a power low model fitted the experimental results accurately for pyrolysis and combustion, respectively. The pyrolysis of poultry waste was a complex process, occurring up to 1300 deg C with high activation energies.

  7. Synfuels from fusion: producing hydrogen with the tandem mirror reactor and thermochemical cycles

    Energy Technology Data Exchange (ETDEWEB)

    Ribe, F.L.; Werner, R.W.

    1981-01-21

    This report examines, for technical merit, the combination of a fusion reactor driver and a thermochemical plant as a means for producing synthetic fuel in the basic form of hydrogen. We studied: (1) one reactor type - the Tandem Mirror Reactor - wishing to use to advantage its simple central cell geometry and its direct electrical output; (2) two reactor blanket module types - a liquid metal cauldron design and a flowing Li/sub 2/O solid microsphere pellet design so as to compare the technology, the thermal-hydraulics, neutronics and tritium control in a high-temperature operating mode (approx. 1200 K); (3) three thermochemical cycles - processes in which water is used as a feedstock along with a high-temperature heat source to produce H/sub 2/ and O/sub 2/.

  8. Thermochemical pretreatments for enhancing succinic acid production from industrial hemp (Cannabis sativa L.).

    Science.gov (United States)

    Gunnarsson, Ingólfur B; Kuglarz, Mariusz; Karakashev, Dimitar; Angelidaki, Irini

    2015-04-01

    The aim of this study was to develop an efficient thermochemical method for treatment of industrial hemp biomass, in order to increase its bioconversion to succinic acid. Industrial hemp was subjected to various thermochemical pretreatments using 0-3% H2SO4, NaOH or H2O2 at 121-180°C prior to enzymatic hydrolysis. The influence of the different pretreatments on hydrolysis and succinic acid production by Actinobacillus succinogenes 130Z was investigated in batch mode, using anaerobic bottles and bioreactors. Enzymatic hydrolysis and fermentation of hemp material pretreated with 3% H2O2 resulted in the highest overall sugar yield (73.5%), maximum succinic acid titer (21.9 g L(-1)), as well as the highest succinic acid yield (83%). Results obtained clearly demonstrated the impact of different pretreatments on the bioconversion efficiency of industrial hemp into succinic acid. Copyright © 2015. Published by Elsevier Ltd.

  9. Fully Bayesian Experimental Design for Pharmacokinetic Studies

    Directory of Open Access Journals (Sweden)

    Elizabeth G. Ryan

    2015-03-01

    Full Text Available Utility functions in Bayesian experimental design are usually based on the posterior distribution. When the posterior is found by simulation, it must be sampled from for each future dataset drawn from the prior predictive distribution. Many thousands of posterior distributions are often required. A popular technique in the Bayesian experimental design literature, which rapidly obtains samples from the posterior, is importance sampling, using the prior as the importance distribution. However, importance sampling from the prior will tend to break down if there is a reasonable number of experimental observations. In this paper, we explore the use of Laplace approximations in the design setting to overcome this drawback. Furthermore, we consider using the Laplace approximation to form the importance distribution to obtain a more efficient importance distribution than the prior. The methodology is motivated by a pharmacokinetic study, which investigates the effect of extracorporeal membrane oxygenation on the pharmacokinetics of antibiotics in sheep. The design problem is to find 10 near optimal plasma sampling times that produce precise estimates of pharmacokinetic model parameters/measures of interest. We consider several different utility functions of interest in these studies, which involve the posterior distribution of parameter functions.

  10. Experimental study of natural circulation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Lemos, Wanderley F.; Su, Jian, E-mail: wlemos@lasme.coppe.ufrj.br, E-mail: sujian@lasme.coppe.ufrj.br [Coordenacao dos Programas de Pos-Graduacao de Engenharia (LASME/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Simulacao e Metodos Numericos; Faccini, Jose L.H., E-mail: faccini@ien.gov.br [Instituto de Engenharia Nuclear (LTE/IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Lab. de Termo-Hidraulica Experimental

    2011-07-01

    This work presents an experimental study about fluid flows behavior in natural circulation, under conditions of single-phase flow. The experiment was performed through experimental thermal-hydraulic circuit built at IEN. This test equipment has performance similar to passive system of residual heat removal present in Advanced Pressurized Water Reactors (APWR). This experimental study aims to observing and analyzing the natural circulation phenomenon, using this experimental circuit that was dimensioned and built based on concepts of similarity and scale. This philosophy allows the analysis of natural circulation behavior in single-phase flow conditions proportionally to the functioning real conditions of a nuclear reactor. The experiment was performed through procedures to initialization of hydraulic feeding of primary and secondary circuits and electrical energizing of resistors installed inside heater. Power controller has availability to adjust values of electrical power to feeding resistors, in order to portray several conditions of energy decay of nuclear reactor in a steady state. Data acquisition system allows the measurement and monitoring of the evolution of the temperature in various points through thermocouples installed in strategic points along hydraulic circuit. The behavior of the natural circulation phenomenon was monitored by graphical interface on computer screen, showing the temperature evolutions of measuring points and results stored in digital spreadsheets. The results stored in digital spreadsheets allowed the getting of data to graphic construction and discussion about natural circulation phenomenon. Finally, the calculus of Reynolds number allowed the establishment for a correlation of friction in function of geometric scales of length, heights and cross section of tubing, considering a natural circulation flow throughout in the region of hot leg. (author)

  11. Experimental study on partial coherence source

    CERN Document Server

    Zhao Xue Qing; Yuan Xiao; LiuJingRu; Wang Long Hua; Tang Ying; Huang, Kerson

    2002-01-01

    Partial coherence source is a key part in the laser system using echelon-free introduced spatial incoherence beam smoothing technique. Different kinds of partial coherence sources have been studied experimentally for improving the uniformity of laser intensity distribution. It is found that the source produced by excimer laser scattering on the surface of a teflon plate is ideal. The properties of this kind of source are studied. As a result, the uniformity of source beam intensity distribution, the beam spatial coherence and energy transfer efficiency of the source are obtained

  12. Comprehensive Mechanisms for Combustion Chemistry: An Experimental and Numerical Study with Emphasis on Applied Sensitivity Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Dryer, Frederick L.

    2009-04-10

    This project was an integrated experimental/numerical effort to study pyrolysis and oxidation reactions and mechanisms for small-molecule hydrocarbon structures under conditions representative of combustion environments. The experimental aspects of the work were conducted in large-diameter flow reactors, at 0.3 to 18 atm pressure, 500 to 1100 K temperature, and 10-2 to 2 seconds reaction time. Experiments were also conducted to determine reference laminar flame speeds using a premixed laminar stagnation flame experiment and particle image velocimetry, as well as pressurized bomb experiments. Flow reactor data for oxidation experiments include: (1)adiabatic/isothermal species time-histories of a reaction under fixed initial pressure, temperature, and composition; to determine the species present after a fixed reaction time, initial pressure; (2)species distributions with varying initial reaction temperature; (3)perturbations of a well-defined reaction systems (e.g. CO/H2/O2 or H2/O2)by the addition of small amounts of an additive species. Radical scavenging techniques are applied to determine unimolecular decomposition rates from pyrolysis experiments. Laminar flame speed measurements are determined as a function of equivalence ratio, dilution, and unburned gas temperature at 1 atm pressure. Hierarchical, comprehensive mechanistic construction methods were applied to develop detailed kinetic mechanisms which describe the measurements and literature kinetic data. Modeling using well-defined and validated mechanisms for the CO/H2/Oxidant systems and perturbations of oxidation experiments by small amounts of additives were also used to derive absolute reaction rates and to investigate the compatibility of published elementary kinetic and thermochemical information. Numerical tools were developed and applied to assess the importance of individual elementary reactions to the predictive performance of the

  13. Membranes for H2 generation from nuclear powered thermochemical cycles.

    Energy Technology Data Exchange (ETDEWEB)

    Nenoff, Tina Maria; Ambrosini, Andrea; Garino, Terry J.; Gelbard, Fred; Leung, Kevin; Navrotsky, Alexandra (University of California, Davis, CA); Iyer, Ratnasabapathy G. (University of California, Davis, CA); Axness, Marlene

    2006-11-01

    In an effort to produce hydrogen without the unwanted greenhouse gas byproducts, high-temperature thermochemical cycles driven by heat from solar energy or next-generation nuclear power plants are being explored. The process being developed is the thermochemical production of Hydrogen. The Sulfur-Iodide (SI) cycle was deemed to be one of the most promising cycles to explore. The first step of the SI cycle involves the decomposition of H{sub 2}SO{sub 4} into O{sub 2}, SO{sub 2}, and H{sub 2}O at temperatures around 850 C. In-situ removal of O{sub 2} from this reaction pushes the equilibrium towards dissociation, thus increasing the overall efficiency of the decomposition reaction. A membrane is required for this oxygen separation step that is capable of withstanding the high temperatures and corrosive conditions inherent in this process. Mixed ionic-electronic perovskites and perovskite-related structures are potential materials for oxygen separation membranes owing to their robustness, ability to form dense ceramics, capacity to stabilize oxygen nonstoichiometry, and mixed ionic/electronic conductivity. Two oxide families with promising results were studied: the double-substituted perovskite A{sub x}Sr{sub 1-x}Co{sub 1-y}B{sub y}O{sub 3-{delta}} (A=La, Y; B=Cr-Ni), in particular the family La{sub x}Sr{sub 1-x}Co{sub 1-y}Mn{sub y}O{sub 3-{delta}} (LSCM), and doped La{sub 2}Ni{sub 1-x}M{sub x}O{sub 4} (M = Cu, Zn). Materials and membranes were synthesized by solid state methods and characterized by X-ray and neutron diffraction, SEM, thermal analyses, calorimetry and conductivity. Furthermore, we were able to leverage our program with a DOE/NE sponsored H{sub 2}SO{sub 4} decomposition reactor study (at Sandia), in which our membranes were tested in the actual H{sub 2}SO{sub 4} decomposition step.

  14. Reuse of microalgae grown in full-scale wastewater treatment ponds: Thermochemical pretreatment and biogas production.

    Science.gov (United States)

    Passos, Fabiana; Felix, Leonardo; Rocha, Hemyle; Pereira, Jackson de Oliveira; de Aquino, Sérgio

    2016-06-01

    This study assessed thermochemical pretreatment of microalgae harvested from a full-scale wastewater treatment pond prior to its anaerobic digestion using acid and alkaline chemical doses combined with thermal pretreatment at 80°C. Results indicated that alkaline and thermal pretreatment contributed mostly to glycoprotein and pectin solubilisation; whilst acid pretreatment solubilised mostly hemicellulose, with lower effectiveness for proteins. Regarding the anaerobic biodegradability, biochemical methane potential (BMP) tests showed that final methane yield was enhanced after almost all pretreatment conditions when compared to non-pretreated microalgae, with the highest increase for thermochemical pretreatment at the lowest dose (0.5%), i.e. 82% and 86% increase for alkaline and acid, respectively. At higher doses, salt toxicity was revealed by K(+) concentrations over 5000mg/L. All BMP data from pretreated biomass was successfully described by the modified Gompertz model and optimal condition (thermochemical 0.5% HCl) showed an increase in final methane yield and the process kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. EXPERIMENTAL STUDIES ON EUPHORBIA PROSTATA W. AIT

    OpenAIRE

    Shrama, Gopal Dutt; Tripathi, S. N.

    1983-01-01

    SUMMARY Water soluble fraction of total alcoholic in the treatment of bronchial asthma 1.2. The same fraction is studied here on frog heart and on blood pressure and respiration of dog, to screen its action on cardio vascular and respiratory systems experimentally. The paper deals with the above experiments with their observations and results. In nut shell the drug is found to have cardiac depresent action an isolated frog heart as well as on frog heart in situ. The drug also possesses potent...

  16. Organ models in wound ballistics: experimental study.

    Science.gov (United States)

    Ozer, Mustafa Tahir; Oğünç, Gökhan; Eryilmaz, Mehmet; Yiğit, Taner; Menteş, Mustafa Oner; Dakak, Mehmet; Uzar, Ali Ihsan; Oner, Köksal

    2007-01-01

    Effects of various types and diameters of guns and related treatment principles are different. Our study was performed to experimentally demonstrate the effects of different gunshots in body tissues. 9x19 mm hand-gun and 7.62x51 mm G-3 infantry rifle were used in the study. Injury models were created through hand-gun and rifle shootings at isolated soft tissue, lower extremity, liver and intestine tissue simulants made of ballistic candle. High-speed cameras were used to capture 1000 frames per second. Images were examined and wound mechanisms were evaluated. It was observed that the colon content distributed more within the surrounding tissues by the rifle shootings comparing with hand-gun shootings and could be an infection source due to the large size of the cavity in the colon. Especially when the bullets hitting the bone were investigated, it was seen that much more tissue injury occurs with high speed bullets due to bullet deformation and fragmentation. However, no significant difference was found between the effect of hand-gun and rifle bullets passing through the extremity without hitting the bone. To know the type of the gun that caused the injury and its characteristics will allow to estimate severity and size of the injury before the treatment and to focus on different alternatives of treatment. Therefore, use of appropriate models is required in experimental studies.

  17. Systematic validation of non-equilibrium thermochemical models using Bayesian inference

    KAUST Repository

    Miki, Kenji

    2015-10-01

    © 2015 Elsevier Inc. The validation process proposed by Babuška et al. [1] is applied to thermochemical models describing post-shock flow conditions. In this validation approach, experimental data is involved only in the calibration of the models, and the decision process is based on quantities of interest (QoIs) predicted on scenarios that are not necessarily amenable experimentally. Moreover, uncertainties present in the experimental data, as well as those resulting from an incomplete physical model description, are propagated to the QoIs. We investigate four commonly used thermochemical models: a one-temperature model (which assumes thermal equilibrium among all inner modes), and two-temperature models developed by Macheret et al. [2], Marrone and Treanor [3], and Park [4]. Up to 16 uncertain parameters are estimated using Bayesian updating based on the latest absolute volumetric radiance data collected at the Electric Arc Shock Tube (EAST) installed inside the NASA Ames Research Center. Following the solution of the inverse problems, the forward problems are solved in order to predict the radiative heat flux, QoI, and examine the validity of these models. Our results show that all four models are invalid, but for different reasons: the one-temperature model simply fails to reproduce the data while the two-temperature models exhibit unacceptably large uncertainties in the QoI predictions.

  18. Radiation thermo-chemical models of protoplanetary discs - III. Impact of inner rims on spectral energy distributions

    NARCIS (Netherlands)

    Thi, W. -F.; Woitke, P.; Kamp, I.

    We study the hydrostatic density structure of the inner disc rim around Herbig Ae stars using the thermo-chemical hydrostatic code prodimo. We compare the spectral energy distributions (SEDs) and images from our hydrostatic disc models to that from prescribed density structure discs. The 2D

  19. Experimental study of rf pulsed heating

    CERN Document Server

    Laurent, L; Nantista, C; Dolgashev, V; Higashi, Y; Aicheler, M; Tantawi, S; Wuensch, W

    2011-01-01

    Cyclic thermal stresses produced by rf pulsed heating can be the limiting factor on the attainable reliable gradients for room temperature linear accelerators. This is especially true for structures that have complicated features for wakefield damping. These limits could be pushed higher by using special types of copper, copper alloys, or other conducting metals in constructing partial or complete accelerator structures. Here we present an experimental study aimed at determining the potential of these materials for tolerating cyclic thermal fatigue due to rf magnetic fields. A special cavity that has no electric field on the surface was employed in these studies. The cavity shape concentrates the magnetic field on one flat surface where the test material is placed. The materials tested in this study have included oxygen free electronic grade copper, copper zirconium, copper chromium, hot isostatically pressed copper, single crystal copper, electroplated copper, Glidcop (R), copper silver, and silver plated co...

  20. Rules of Thumb (Empirical Rules) for the Biomass Utilization by Thermochemical Conversion

    National Research Council Canada - National Science Library

    ANTAL, Jr, Michael J; HELSEN, Lieve M; KOUZU, Masato; LÉDÉ, Jacques; MATSUMURA, Yukihiko

    2014-01-01

    The rules of thumb for developing thermochemical conversion technology are introduced together with the fundamental rules of thumb for thermochemical conversion, which is the basic idea for these technologies...

  1. Thermochemical Conversion: Using Heat and Catalysts to Make Biofuels and Bioproducts

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-07-29

    This fact sheet discusses the Bioenergy Technologies Office's thermochemical conversion critical technology goal. And, how through the application of heat, robust thermochemical processes can efficiently convert a broad range of biomass.

  2. An Experimental Study of Soft Lubrication

    Science.gov (United States)

    Wu, Qianhong; Gacka, Thomas; Nathan, Rungun; Wu, Li-Zhu; Cbmss Team

    2012-11-01

    Lift generation in soft porous media, as a planing surface glides over it, is a new topic in porous media flow with superior potential for lubrication and squeeze damping. This paper presents the first experimental study of this phenomenon. The experimental setup consists of a running conveyer belt covered with a soft porous sheet, and a stationary instrumented inclined planar upper board. Twelve pressure transducers mounted on the upper board captured the pore pressure generation, while a load cell was used to capture the total lifting force, arising from both the pore pressure and the compression of the solid fibers. One finds that the pore pressure distribution is consistent with theoretical predictions (Feng and Weinbaum, JFM, 2000; Wu et al., MSSE, 2006, 2011), and depends on the running belt velocity, U, the mechanical properties of the porous material, and the compression ratios of the porous layer. For a typical trial (h2/h1=5,h2/h0=1, U=3.8 m/s, where h2, h1, and h0 are the leading edge, trailing edge, and undeformed porous layer thicknesses, respectively), 68% of the lifting force was generated by the pore pressure. It conclusively demonstrates the validity of using soft porous materials for super lubrication. applications. Villanova Cellular Biomechanics and Sports Science Laboratory.

  3. Experimental Study of Separate Type Thermosyphon

    Science.gov (United States)

    Hirashima, Masao; Kawahata, Kenya; Negishi, Kanji

    The passages of vapor flow and the returning liquid flow are perfectly partitioned in a separate type thermosyphon. Therefore the flooding limit can be eliminated and practicability based on its construction is highly evaluated. The carry-over of the liquid into the condensing section accompanied with the rising vapor flow should be avoided in the separate type thermosyphon, since it causes to decrease the heat transfer coefficient on the heat transfer surface in the condenser. In the present work, the effect of liquid level, the heat input into the evaporating section, the charging rate of the liquid, and the dimension of the adiabatic section supposed on the generation of carry-over were studied experimentally. The frequency of the bumping and the velocity of the vapor in the adiabatic section were examined as the function of the termination of the carry-over. The experimental correlation representing the relation among the elapsed time, the liquid temperature and the charging rate of the liquid were also derived.

  4. Evaluation of wastewater treatment requirements for thermochemical biomass liquefaction

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, D C [Pacific Northwest Lab., Richland, WA (United States)

    1992-04-01

    Biomass can provide a substantial energy source. Liquids are preferred for use as transportation fuels because of their high energy density and handling ease and safety. Liquid fuel production from biomass can be accomplished by any of several different processes including hydrolysis and fermentation of the carbohydrates to alcohol fuels, thermal gasification and synthesis of alcohol or hydrocarbon fuels, direct extraction of biologically produced hydrocarbons such as seed oils or algae lipids, or direct thermochemical conversion of the biomass to liquids and catalytic upgrading to hydrocarbon fuels. This report discusses direct thermochemical conversion to achieve biomass liquefaction and the requirements for wastewater treatment inherent in such processing. 21 refs.

  5. Metabolic Desynchronization in Critical Conditions: Experimental Study

    Directory of Open Access Journals (Sweden)

    G. V. Livanov

    2006-01-01

    Full Text Available Objective. To conduct an experimental study of the impact of the time of administration of succinic acid preparations on central nervous system (CNS function and gas exchange while simulating metabolic therapy for severe poisoning by ethyl alcohol. The study was performed on 74 male albino rats weighing 140—180 g. Acute severe and very severe intoxication was simulated, by intraabdominally administering 30% ethanol to the rats. Cytoflavin was used to simulate experimental therapy. The rate of gas exchange was estimated by the oxygen uptake determined by the closed chamber method in a Regnault apparatus (Germany. Spontaneous bioelectrical activity was recorded in the frontooccipital lead by the routine procedure. External pain stimulation and rhythmical photostimulation were employed to evaluate cerebral responsiveness. Heterodirectional EEG changes in the «early» and «late» administration of succinate were not followed by the similar alterations of gas exchange: oxygen consumption in both the «early» and «late» administration of succinate remained significantly lower than in the control animals. With the late administration of succinate to the animals with mixed (toxic and hypoxic coma, the so-called discrepancy between the noticeably increased energy production and brutally diminished metabolism occurred. It may be just the pathological mechanism that was the basis for higher mortality in the late succinate administration group. The findings and their analysis make it possible to advance a hypothesis that succinate may cause metabolic desynchronization if activation of metabolic processes takes place under severe tissue respiratory tissue depression. In these cases, there is a severe damage to tissue and chiefly the brain. This manifests itself as EEG epileptiform activity splashes preceding the animals’ death. Therefore, resuscitation aimed at restoring the transport of oxygen and its involvement in tissue energy processes should

  6. Contribution to the experimental study of the hydraulic jump in ...

    African Journals Online (AJOL)

    The purpose of this study is to study experimentally the hydraulic jump evolving in a symmetric trapezoidal channel with a positive slope, requires the use of an experimental protocol, and to find experimental relations linking the characteristics of the formed projection. The experimental study investigated the variation of the ...

  7. A thermochemically derived global reaction mechanism for detonation application

    Science.gov (United States)

    Zhu, Y.; Yang, J.; Sun, M.

    2012-07-01

    A 4-species 4-step global reaction mechanism for detonation calculations is derived from detailed chemistry through thermochemical approach. Reaction species involved in the mechanism and their corresponding molecular weight and enthalpy data are derived from the real equilibrium properties. By substituting these global species into the results of constant volume explosion and examining the evolution process of these global species under varied conditions, reaction paths and corresponding rates are summarized and formulated. The proposed mechanism is first validated to the original chemistry through calculations of the CJ detonation wave, adiabatic constant volume explosion, and the steady reaction structure after a strong shock wave. Good agreement in both reaction scales and averaged thermodynamic properties has been achieved. Two sets of reaction rates based on different detailed chemistry are then examined and applied for numerical simulations of two-dimensional cellular detonations. Preliminary results and a brief comparison between the two mechanisms are presented. The proposed global mechanism is found to be economic in computation and also competent in description of the overall characteristics of detonation wave. Though only stoichiometric acetylene-oxygen mixture is investigated in this study, the method to derive such a global reaction mechanism possesses a certain generality for premixed reactions of most lean hydrocarbon mixtures.

  8. Optimization of thermo-chemical hydrolysis of kitchen wastes.

    Science.gov (United States)

    Vavouraki, Aikaterini Ioannis; Angelis, Evangelos Michael; Kornaros, Michael

    2013-03-01

    Municipal Solid Wastes (MSWs) in Greece consist mainly of fermentable organic material such as food scraps (∼50%) and paper residuals (∼20%). The aim of this work was to study the thermo-chemical pretreatment of the kitchen waste (KW) fraction of MSW focusing on biotechnological exploitation of pretreated wastes for biofuel production. A representative sample of municipal food residues was derived by combining weighted amounts of each individual type of residue recognized in daily samples obtained from the University of Patras' students restaurant located at the Students Residence Hall (Greece). Chemical pretreatment experiments of the representative KW sample were performed using several types of chemical solutions (i.e. H2SO4, HCl, NaOH, H2SO3) of different solute concentration (0.7%, 1.5%, 3%) at three temperatures (50, 75, 120°C) and a range of residence times (30-120min). Optimized results proved that chemical pretreatment of KW, using either 1.12% HCl for 94min or 1.17% HCl for 86min (at 100°C), increased soluble sugars concentration by 120% compared to untreated KW. The increase of soluble sugars was mainly attributed to the mono-sugars glucose and fructose. Copyright © 2012 Elsevier Ltd. All rights reserved.

  9. Thermochemical hydrogen generation of indium oxide thin films

    Directory of Open Access Journals (Sweden)

    Taekyung Lim

    2017-03-01

    Full Text Available Development of alternative energy resources is an urgent requirement to alleviate current energy constraints. As such, hydrogen gas is gaining attention as a future alternative energy source to address existing issues related to limited energy resources and air pollution. In this study, hydrogen generation by a thermochemical water-splitting process using two types of In2O3 thin films was investigated. The two In2O3 thin films prepared by chemical vapor deposition (CVD and sputtering deposition systems contained different numbers of oxygen vacancies, which were directly related to hydrogen generation. The as-grown In2O3 thin film prepared by CVD generated a large amount of hydrogen because of its abundant oxygen vacancies, while that prepared by sputtering had few oxygen vacancies, resulting in low hydrogen generation. Increasing the temperature of the In2O3 thin film in the reaction chamber caused an increase in hydrogen generation. The oxygen-vacancy-rich In2O3 thin film is expected to provide a highly effective production of hydrogen as a sustainable and efficient energy source.

  10. Thermochemical liquefaction characteristics of microalgae in sub- and supercritical ethanol

    Energy Technology Data Exchange (ETDEWEB)

    You, Qiao; Chen, Liang [College of Environmental Science and Engineering, Hunan University, Changsha (China); Key Laboratory of Environment Biology and Pollution Control, Ministry of Education, Changsha (China)

    2011-01-15

    Thermochemical liquefaction characteristics of Spirulina, a kind of high-protein microalgae, were investigated with the sub- and supercritical ethanol as solvent in a 1000 mL autoclave. The influences of various liquefaction parameters on the yields of products (bio-oil and residue) from the liquefaction of Spirulina were studied, such as the reaction temperature (T), the S/L ratio (R{sub 1}, solid: Spirulina, liquid: ethanol), the solvent filling ratio (R{sub 2}) and the type and dosage of catalyst. Without catalyst, the bio-oil yields were in the range of 35.4 wt.% and 45.3 wt.% depending on the changes of T, R{sub 1} and R{sub 2}. And the bio-oil yields increased generally with increasing T and R{sub 2}, while the bio-oil yields reduced with increasing R{sub 1}. The FeS catalyst was certified to be an ideal catalyst for the liquefaction of Spirulina microalgae for its advantages on promoting bio-oil production and suppressing the formation of residue. The optimal dosage of catalyst (FeS) was ranging from 5-7 wt.%. The elemental analyses and FT-IR and GC-MS measurements for the bio-oils revealed that the liquid products have much higher heating values than the crude Spirulina sample and fatty acid ethyl ester compounds were dominant in the bio-oils, irrespective of whether catalyst was used. (author)

  11. Assessment of thermochemical data on steel deoxidation

    Directory of Open Access Journals (Sweden)

    Gómez, P.

    2009-08-01

    Full Text Available It is proposed to develop a method to judge the certainty on the information regarding to deoxidation equilibria of iron melts. To accomplish this objective, thermochemical data was collated and then evaluated. The basic knowledge on deoxidation conditions are framed by the non-ideal Henrian behaviour of diluted solutions of both deoxidizer and oxygen in liquid iron in equilibrium with a pure oxide. Conventional deoxidation reactions were considered at 1,873 K such that in their equilibrium constants, only first order interaction coefficients were considered. The criteria in selecting the most appropriated free energy equation was based on evaluating them under two critical composition points: 1 where they satisfy an oxygen to deoxidizer ratio dictated by its stoichiometry and 2 where oxygen contents at a given amount of deoxidizer reaches a minimum value. These data were plotted on logarithmic scales to appreciate the effects of deoxidizer’s valences. Once such information was classified, under restrictions 1 and 2, previous compositions were related to deoxidizer´s electronegativities.

    El presente artículo propone desarrollar un método para juzgar la certidumbre de la información pertinente al equilibrio de desoxidación de fundidos de hierro. Para lograr este objetivo, se recolectaron y evaluaron datos termoquímicos existentes. Las teorías sobre desoxidación se describen mediante el comportamiento Henriano de soluciones diluidas del agente desoxidante y el hierro fundido en equilibrio con un óxido. En este estudio, solo se consideran reacciones convencionales a 1.873 K, de forma tal que se consideraron las constantes de equilibrio y coeficientes de interacción de primer orden. El criterio empleado para utilizar la expresión más adecuada de la energía libre se basó en evaluar dos puntos críticos: uno, donde se satisface una relación oxígeno/desoxidante dictada por la estequiometría y dos,cuando el contenido de ox

  12. [Endodontics in horses. An experimental study].

    Science.gov (United States)

    Garcia, F; Sanromán, F; Llorens, M P

    1990-04-01

    A total of 44 experimental endodontic treatments were performed in incisors of eight horses of different ages. Four different endodontic pastes were used: Cloropercha, AH26 De Trey, Eugenol-Endometasone, and Universal N2. Gutta-percha points were also included in the last two treatments. Access to the pulp cavity of incisors was gained through their vestibular and occlusal faces. Holes drilled in vestibular faces were sealed with composite and those drilled in occlusal faces were sealed with Amalgama. Animals were observed during eighteen months at least after endodontics. Radiographic controls were done just after surgery and before slaughtering. Treated incisors and alveoli were studied histopathologically. During the experiment all animals were in good condition. They ate apparently without trouble, and neither clinical nor radiological signs were present.

  13. An experimental study of reactive turbulent mixing

    Science.gov (United States)

    Cooper, L. P.; Marek, C. J.; Strehlow, R. A.

    1977-01-01

    An experimental study of the turbulent mixing of two coaxial gas streams, which react very rapidly (pseudo-hypergolic chemical kinetics), was performed to investigate the mixing characteristics of turbulent flow fields. The center stream consisted of a CO-N2 mixture and the outer annular stream consisted of air vitiated by H2 combustion. The streams were at equal velocity (50 m/sec) and temperature (1280 K). Turbulence measurements were obtained using hot film anemometry. A sampling probe was used to obtain time averaged gas compositions. Six different turbulence generators were placed in the annular passage to alter the flow field mixing characteristics. The turbulence generators affected the bulk mixing of the streams and the extent of CO conversion to different degrees. The effects can be related to the average eddy size and the bulk mixing. Higher extents of conversion of CO to CO2 were found by increasing the bulk mixing and decreasing the average eddy size.

  14. Experimental and theoretical study of reflux condensation

    Energy Technology Data Exchange (ETDEWEB)

    Bakke, Knut

    1997-12-31

    This thesis studies the separation of gas mixtures in a reflux condenser. also called a dephlegmator. Reflux condensation is separation of a gas mixture, in reflux flow with condensing liquid, under continuous heat removal. A numerical model of a dephlegmator for binary mixtures was developed. The model may readily be extended to multi-component mixtures, as the solution method is based on a matrix solver. Separation of a binary mixture in a reflux condenser test rig is demonstrated. The test facility contains a single-tube test section that was designed and built as part of the project. Test mixtures of propane and n-butane were used, and a total of 15 experiments are reported. Limited degree of separation was achieved due to limited heat transfer area and narrow boiling point range of the test mixture. The numerical model reproduces the experimental data within reasonable accuracy. Deviation between calculated and measured properties is less than 6% of the measured temperature and less than 5% of the measured flow rate. The model is based on mechanistic models of physical processes and is not calibrated or tuned to fit the experimental data. The numerical model is applied to a number of separation processes. These case studies show that the required heat transfer area increases rapidly with increments in top product composition (light component). Flooding limits the amount of reflux liquid. The dephlegmator is suitable for separation of feed mixtures that are rich in light components. The gliding temperature in the dephlegmation process enables utilization of top product as refrigerant, with subsequent energy saving as a result. 61 refs., 50 figs., 34 tabs.

  15. Experimental Study on Dry Torrefaction of Beech Wood

    NARCIS (Netherlands)

    Gucho, Eyerusalem Merin; Shahzad, K.; Bramer, Eduard A.; Akhtar, N.A.; Brem, Gerrit

    2015-01-01

    Torrefaction is a thermochemical pre-treatment process for upgrading the properties of biomass to resemble those of fossil fuels such as coal. Biomass properties of particular interest are chemical composition, physical property and combustion characteristics. In this work, torrefaction of beech

  16. Experimental studies of ongoing conscious experience.

    Science.gov (United States)

    Singer, J L

    1993-01-01

    A research programme designed to find ways of applying a variety of methods in psychological science to studying the seemingly ephemeral phenomena of the human stream of consciousness and its manifestations in daydreams, interior monologues, imagery and related private experiences is described. Approaches include psychometric studies to establish normative information on daydreaming and experimental studies using signal-detection paradigms to capture the ongoing stream of thought. Recent experiments involve thought-sampling methods for identifying the determinants of the content of the stream of thought in adolescents or the ways in which self-beliefs and emotions are manifested in a group of cocaine and heroin abusers. Children's pretend play is studied as a possible forerunner of adult consciousness. It is proposed that the human condition involves a continuing tension between processing information generated from the physical and social milieu and the continuous operation of centrally generated material from long-term memory in the form of reminiscences, wishes, current concerns, expectancies and fantasies. This concept has implications for personality variation, affective arousal and adaptive behaviour.

  17. Coupled thermochemical, isotopic evolution and heat transfer simulations in highly irradiated UO2 nuclear fuel

    Science.gov (United States)

    Piro, M. H. A.; Banfield, J.; Clarno, K. T.; Simunovic, S.; Besmann, T. M.; Lewis, B. J.; Thompson, W. T.

    2013-10-01

    Predictive capabilities for simulating irradiated nuclear fuel behavior are enhanced in the current work by coupling thermochemistry, isotopic evolution and heat transfer. Thermodynamic models that are incorporated into this framework not only predict the departure from stoichiometry of UO2, but also consider dissolved fission and activation products in the fluorite oxide phase, noble metal inclusions, secondary oxides including uranates, zirconates, molybdates and the gas phase. Thermochemical computations utilize the spatial and temporal evolution of the fission and activation product inventory in the pellet, which is typically neglected in nuclear fuel performance simulations. Isotopic computations encompass the depletion, decay and transmutation of more than 2000 isotopes that are calculated at every point in space and time. These computations take into consideration neutron flux depression and the increased production of fissile plutonium near the fuel pellet periphery (i.e., the so-called “rim effect”). Thermochemical and isotopic predictions are in very good agreement with reported experimental measurements of highly irradiated UO2 fuel with an average burnup of 102 GW d t(U)-1. Simulation results demonstrate that predictions are considerably enhanced when coupling thermochemical and isotopic computations in comparison to empirical correlations. Notice: This manuscript has been authored by UT-Battelle, LLC, under Contract No. DE-AC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes.

  18. Experimental Study of Alluvial Fan Formation

    Science.gov (United States)

    Delorme, P.; Devauchelle, O.; Barrier, L.; Métivier, F.

    2015-12-01

    At the outlet of mountain ranges, rivers flow onto flatter lowlands. The associated change of slope causes sediment deposition. As the river is free to move laterally, it builds conical sedimentary structures called alluvial fans. Their location at the interface between erosional and depositional areas makes them valuable sedimentary archives. To decipher these sedimentary records, we need to understand the dynamics of their growth. Most natural fans are built by braided streams. However, to avoid the complexity of braided rivers, we develop a small-scale experiment in which an alluvial fan is formed by a single channel. We use a mixture of water and glycerol to produce a laminar river. The fluid is mixed with corindon sand (~ 300 μm) in a tilted channel and left free to form a fan around its outlet. The sediment and water discharges are constant during an experimental run. We record the fan progradation and the channel morphology with top-view pictures. We also generate an elevation map with an optical method based on the deformation of a moiré pattern. We observe that, to leading order, the fan remains self-affine as it grows, with a constant slope. We compare two recent studies about the formation of one-dimensionnal fan [Guerit et al. 2014] and threshold rivers [Seizilles et al. 2013] to our experimental findings. In particular, we propose a theory witch relates the fan morphology to the control parameters ( fluid and sediment discharges, grain size). Our observation accord with the predictions, suggesting that the fan is built near the threshold of sediment motion. Finally, we intend to expand our interpretation to alluvial fans build by single-thread channels ( Okavango, Bostwana; Taquari and Paraguay, Brasil; Pastaza, Peru).

  19. Hot forming of composite prepreg : Experimental study

    Science.gov (United States)

    Tardif, Xavier; Duthille, Bertrand; Bechtel, Stephane; le Pinru, Louis; Campagne, Benjamin; Destombes, Gautier; Deshors, Antoine; Marchand, Christophe; Azzouzi, Khalid El; Moro, Tanguy

    2017-10-01

    The hot forming of thermoset prepreg consists in bending an uncured composite part by applying a mechanical constrain on the hot laminate. Most of the time, the mold is inserted in a vacuum box and the mechanical constrain is applied on the composite laminate by a single membrane or a double-membrane. But the performance improvement products resulted in forming increasingly complex parts with advanced materials having a less formability. These new complex parts require a finer comprehension of the process and an optimization of the key parameters to get acceptable quality. In this work, an experimental study has been carried out to identify the process conditions that do not lead to unacceptable defaults: undulations of fibers. In the present study, downward-bending has been evaluated with an original light mechanical forming concept, for a given stacking sequence. The influence of the part's temperature and the part's bending speed are investigated. To carry this study out, a hot forming test bench has been designed and manufactured to have a precise supervision of the process conditions. It is able to bend parts of 1500 mm length x 600 mm width x 20 mm thick.

  20. Experimental study of rf pulsed heating

    Directory of Open Access Journals (Sweden)

    Lisa Laurent

    2011-04-01

    Full Text Available Cyclic thermal stresses produced by rf pulsed heating can be the limiting factor on the attainable reliable gradients for room temperature linear accelerators. This is especially true for structures that have complicated features for wakefield damping. These limits could be pushed higher by using special types of copper, copper alloys, or other conducting metals in constructing partial or complete accelerator structures. Here we present an experimental study aimed at determining the potential of these materials for tolerating cyclic thermal fatigue due to rf magnetic fields. A special cavity that has no electric field on the surface was employed in these studies. The cavity shape concentrates the magnetic field on one flat surface where the test material is placed. The materials tested in this study have included oxygen free electronic grade copper, copper zirconium, copper chromium, hot isostatically pressed copper, single crystal copper, electroplated copper, Glidcop®, copper silver, and silver plated copper. The samples were exposed to different machining and heat treatment processes prior to rf processing. Each sample was tested to a peak pulsed heating temperature of approximately 110°C and remained at this temperature for approximately 10×10^{6} rf pulses. In general, the results showed the possibility of pushing the gradient limits due to pulsed heating fatigue by the use of copper zirconium and copper chromium alloys.

  1. Theoretical and experimental studies on the foundation theoretical and experimental studies on the foundation of mesomechanics

    Science.gov (United States)

    Chudnovsky, A.; Wu, S.

    1992-06-01

    The report summarizes a closely coupled experimental and theoretical investigation of various stages of Fracture Process: (1) accumulation of 'damage' on submicroscopical and microscopical scales leading to crack initiation; (2) slow (subcritical) crack growth and an evolution of the damage zone; (3) transition to dynamic crack growth and the catastrophic failure. The experimental part of the program is focused on the observation and quantitative characterization of damage preceding and accompanying crack initiation and growth. A special experimental setup for studying the fracture process under variable stress field is reported in Chapter 2. A leading role of crack-damage interaction in fracture process is well documented. A new formalism for solution of crack-microcrack array interaction problem and its successful implementation in the evaluation of crack layer driving forces is presented in Chapter 3. A new model of the process zone, which generalizes the well-known Dagdale-Barenblatt model is presented in Chapter 4. A new measure for material toughness and the prediction of R-curve behavior illustrate the practical application of our model. Experimental examinations of our model under various test conditions are reported in Chapters 4, 5 and 6. The development of the constitutive equations for Crack Layer evolution and their experimental examinations under stress relaxation, fatigue and creep conditions are reported in Chapters 5 and 6. An accelerated test procedure and the formulation of crack layer instability criteria as a substitution for the conventional fracture toughness parameters are also discussed in Chapter 6.

  2. Experimental studies of herbicide drift characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Renne, D.S.; Wolf, M.A.

    1976-05-20

    A knowledge of the drift characteristics of herbicides and pesticides released from ground and aerial rigs is important in forestry and agricultural applications so that methods for minimizing damage to downwind systems sensitive to these chamicals can be developed. A field experiment was undertaken on the Hanford Reservation in eastern Washington State during 1975 to study techniques for maximizing herbicide applications from a spray airplane on the intended area and minimizing drift. Several early morning experiments comparing drift characteristics of a fixed with a test application for various nozzle systems and herbicide concentrations were made. The results of these experiments have shown that the initial drift and drift deposit components varied by only a factor of two or so, depending on the production of smaller droplets, as various techniques were used to put the herbicides down from the aircraft. Meteorological conditions become increasingly important at greater downwind distances from the source. Furthermore, drift reduction was most effective under conditions of high relative humidities and cool temperatures. At large distances from the source, ground level drift was higher on stable than on unstable days. Comments on methods for improving the experimental design, and applications of studies such as these to forestry will be made.

  3. Renewable hydrogen production via thermochemical/electrochemical coupling

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosini, Andrea [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Babiniec, Sean Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, James E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-10-01

    A coupled electrochemical/thermochemical cycle was investigated to produce hydrogen from renewable resources. Like a conventional thermochemical cycle, this cycle leverages chemical energy stored in a thermochemical working material that is reduced thermally by solar energy. However, in this concept, the stored chemical energy only needs to be partially, but not fully, capable of splitting steam to produce hydrogen. To complete the process, a proton-conducting membrane is driven to separate hydrogen as it is produced, thus shifting the thermodynamics toward further hydrogen production. This novel coupled-cycle concept provides several benefits. First, the required oxidation enthalpy of the reversible thermochemical material is reduced, enabling the process to occur at lower temperatures. Second, removing the requirement for spontaneous steam-splitting widens the scope of materials compositions, allowing for less expensive/more abundant elements to be used. Lastly, thermodynamics calculations suggest that this concept can potentially reach higher efficiencies than photovoltaic-to-electrolysis hydrogen production methods. This Exploratory Express LDRD involved assessing the practical feasibility of the proposed coupled cycle. A test stand was designed and constructed and proton-conducting membranes were synthesized. While the full proof of concept was not achieved, the individual components of the experiment were validated and new capabilities that can be leveraged by a variety of programs were developed.

  4. Fuel cell efficiency in a combined electrochemical-thermochemical process

    Science.gov (United States)

    Balko, E. N.; Avery, W.

    The thermodynamics of an H2/Cl2 fuel cell combined with a thermochemical hydrogen chloride oxidation stage are considered. Such a cycle is superior to the phosphoric acid H2/O2 systems but does not better the efficiency demonstrated in more advanced H2/O2 fuel cell systems.

  5. Biomass Program 2007 Program Peer Review - Thermochemical Conversion Platform Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biomass Program Peer Review for the Thermochemical Platform, held on July 9th and 10th in Golden, Colorado.

  6. Thermochemical characteristics of cellulose acetates with different degrees of acetylation

    Science.gov (United States)

    Larina, V. N.; Ur'yash, V. F.; Kushch, D. S.

    2012-12-01

    The standard enthalpies of combustion and formation of cellulose acetates with different degrees of acetylation are determined. It is established that there is a proportional dependence of these thermochemical characteristics vs. the degree of acetylation, weight fraction of bonded acetic acid, and molar mass of the repeating unit of cellulose acetates.

  7. Thermo-chemical sequestration of naphthalene using Borassus ...

    African Journals Online (AJOL)

    admin

    2016-11-30

    Nov 30, 2016 ... characterization thoroughly suggests the efficacy of B. flabellifer shell to efficiently sequester naphthalene from aqueous solution. Key words: Naphthalene, Borassus flabellifer, thermo-chemical, activated carbon, adsorption. ..... Nickel treatment in the Electroplating effluent with Activated carbon prepared ...

  8. Thermochemical Surface Engineering: A Playground for Science and Innovation

    DEFF Research Database (Denmark)

    Christiansen, Thomas Lundin; Dahl, Kristian Vinter; Jellesen, Morten Stendahl

    2017-01-01

    at the surface. Current research and innovation activities are used to exemplify thermochemical surface engineering and the interplay of science and innovation. The examples given encompass aspects of the synthesis of extremely porous materials, low temperature surface hardening of stainless steel, surface...

  9. Cascading pressure reactor and method for solar-thermochemical reactions

    Energy Technology Data Exchange (ETDEWEB)

    Ermanoski, Ivan

    2017-11-14

    Reactors and methods for solar thermochemical reactions are disclosed. The reactors and methods include a cascade of reduction chambers at successively lower pressures that leads to over an order of magnitude pressure decrease compared to a single-chambered design. The resulting efficiency gains are substantial, and represent an important step toward practical and efficient solar fuel production on a large scale.

  10. Carbonate thermochemical cycle for the production of hydrogen

    Science.gov (United States)

    Collins, Jack L [Knoxville, TN; Dole, Leslie R [Knoxville, TN; Ferrada, Juan J [Knoxville, TN; Forsberg, Charles W [Oak Ridge, TN; Haire, Marvin J [Oak Ridge, TN; Hunt, Rodney D [Oak Ridge, TN; Lewis, Jr, Benjamin E [Knoxville, TN; Wymer, Raymond G [Oak Ridge, TN

    2010-02-23

    The present invention is directed to a thermochemical method for the production of hydrogen from water. The method includes reacting a multi-valent metal oxide, water and a carbonate to produce an alkali metal-multi-valent metal oxide compound, carbon dioxide, and hydrogen.

  11. Thermochemically Driven Gas-Dynamic Fracturing (TDGF)

    Energy Technology Data Exchange (ETDEWEB)

    Michael Goodwin

    2008-12-31

    This report concerns efforts to increase oil well productivity and efficiency via a method of heating the oil-bearing rock of the well, a technique known as Thermochemical Gas-Dynamic Fracturing (TGDF). The technique uses either a chemical reaction or a combustion event to raise the temperature of the rock of the well, thereby increasing oil velocity, and oil pumping rate. Such technology has shown promise for future application to both older wellheads and also new sites. The need for such technologies in the oil extraction field, along with the merits of the TGDF technology is examined in Chapter 1. The theoretical basis underpinning applications of TGDF is explained in Chapter 2. It is shown that productivity of depleted well can be increased by one order of magnitude after heating a reservoir region of radius 15-20 m around the well by 100 degrees 1-2 times per year. Two variants of thermal stimulation are considered: uniform heating and optimal temperature distribution in the formation region around the perforation zone. It is demonstrated that the well productivity attained by using equal amounts of thermal energy is higher by a factor of 3 to 4 in the case of optimal temperature distribution as compared to uniform distribution. Following this theoretical basis, two practical approaches to applying TDGF are considered. Chapter 3 looks at the use of chemical intiators to raise the rock temperature in the well via an exothermic chemical reaction. The requirements for such a delivery device are discussed, and several novel fuel-oxidizing mixtures (FOM) are investigated in conditions simulating those at oil-extracting depths. Such FOM mixtures, particularly ones containing nitric acid and a chemical initiator, are shown to dramatically increase the temperature of the oil-bearing rock, and thus the productivity of the well. Such tests are substantiated by preliminary fieldwork in Russian oil fields. A second, more cost effective approach to TGDF is considered in

  12. Experimental studies of fiber concrete creep

    Directory of Open Access Journals (Sweden)

    Korneeva Irina

    2017-01-01

    Full Text Available The results of two-stage experimental studies of the strength and deformation characteristics of fibrous concrete reinforced with steel fiber. In the experiments we used steel fiber with bent ends, which practically does not form "hedgehogs", which allows to achieve an even distribution of the fiber by volume. At the first stage, the cube and prismatic strength, deformability at central compression, a number of special characteristics are determined: water absorption, frost resistance, abrasion; the optimal percentage of fiber reinforcement and the maximum size of the coarse aggregate fraction were selected. Fiber reinforcement led to an increase in the strength of concrete at compression by 1,35 times and an increase in the tensile strength at bending by 3,4 times. At the second stage, the creep of fibrous concrete and plain concrete of similar composition at different stress levels was researched. Creep curves are plotted. It is shown that the use of fiber reinforcement leads to a decrease in creep strain by 21 to 30 percent, depending on the stress level.

  13. Experimental study of finite Larmor radius effects

    Energy Technology Data Exchange (ETDEWEB)

    Struve, K.W.

    1980-08-01

    Linear Z-pinches in Ar, Kr, Xe, N/sub 2/, and He are experimentally studied in regimes where strong finite Larmor radius effects could provide a significant stabilizing effect. Scaling arguments show that for deuterium such a pinch has an electron line density of order 2 x 10/sup 15//cm. For higher Z plasmas a higher line density is allowed, the exact value of which depends on the average ion charge. The pinch is formed by puffing gas axially through the cathode towards the anode of an evacuated pinch chamber. When the gas reaches the anode, the pinch bank is fired. The pinch current rises in 2 to 3 ..mu..sec to a maximum of 100 to 200 kA. The pinch bank capacitance is 900 ..mu..F, and the external inductance is 100 nH. Additionally, the bank is fused to increase dI/dt. The primary diagnostics are a framing camera, a spatially resolved Mach-Zehnder interferometer, and X-ray absorption.

  14. The experimental studies of thermoacoustic cooler.

    Science.gov (United States)

    Sakamoto, Shin-ichi; Watanabe, Yoshiaki

    2004-04-01

    The experimental studies of thermoacoustic cooler consisting of acoustic loop-tube were carried out. The loop-tube was filled with the mixture of air and helium gas or air at atmospheric pressure. The dimensions of the loop-tube were 3.3 m of length, 44 mm of inner diameter and 4 mm of thickness. A pair of stacks (stack 1 and stack 2) which were sandwiched between two heat exchangers was placed symmetrically in the loop-tube. Stack 1 was employed as a prime mover and stack 2 as a heat pump. The self-sustained sound generated by the thermoacoustic effect and the cooling phenomena at the stack 2 were observed. The distribution of the sound pressures and the waveforms in the loop-tube were measured, and the frequency component of the self-sustained sound was investigated at the starting phase. The fundamental frequency component was confirmed and it was developing as the sound pressure increasing. The higher harmonics frequency components were generated and they were also developing.

  15. Experimental study of trimethyl aluminum decomposition

    Science.gov (United States)

    Zhang, Zhi; Pan, Yang; Yang, Jiuzhong; Jiang, Zhiming; Fang, Haisheng

    2017-09-01

    Trimethyl aluminum (TMA) is an important precursor used for metal-organic chemical vapor deposition (MOCVD) of most Al-containing structures, in particular of nitride structures. The reaction mechanism of TMA with ammonia is neither clear nor certain due to its complexity. Pyrolysis of trimethyl metal is the start of series of reactions, thus significantly affecting the growth. Experimental study of TMA pyrolysis, however, has not yet been conducted in detail. In this paper, a reflectron time-of-flight mass spectrometer is adopted to measure the TMA decomposition from room temperature to 800 °C in a special pyrolysis furnace, activated by soft X-ray from the synchrotron radiation. The results show that generation of methyl, ethane and monomethyl aluminum (MMA) indicates the start of the pyrolysis process. In the low temperature range from 25 °C to 700 °C, the main product is dimethyl aluminum (DMA) from decomposition of TMA. For temperatures larger than 700 °C, the main products are MMA, DMA, methyl and ethane.

  16. Learning, forecasting and optimizing : An experimental study

    NARCIS (Netherlands)

    Bao, Te; Duffy, John; Hommes, Cars

    Rational Expectations (RE) models have two crucial dimensions: (i) agents on average correctly forecast future prices given all available information, and (ii) given expectations, agents solve optimization problems and these solutions in turn determine actual price realizations. Experimental tests

  17. Evapotranspiration studies for protective barriers: Experimental plans

    Energy Technology Data Exchange (ETDEWEB)

    Link, S.O.; Waugh, W.J.

    1989-11-01

    This document describes a general theory and experimental plans for predicting evapotranspiration in support of the Protective Barrier Program. Evapotranspiration is the combined loss of water from plants and soil surfaces to the atmosphere. 45 refs., 1 fig., 4 tabs.

  18. Experimental and computational studies of nanofluids

    Science.gov (United States)

    Vajjha, Ravikanth S.

    The goals of this dissertation were (i) to experimentally investigate the fluid dynamic and heat transfer performance of nanofluids in a circular tube, (ii) to study the influence of temperature and particle volumetric concentration of nanofluids on thermophysical properties, heat transfer and pumping power, (iii) to measure the rheological properties of various nanofluids and (iv) to investigate using a computational fluid dynamic (CFD) technique the performance of nanofluids in the flat tube of a radiator. Nanofluids are a new class of fluids prepared by dispersing nanoparticles with average sizes of less than 100 nm in traditional heat transfer fluids such as water, oil, ethylene glycol and propylene glycol. In cold regions of the world, the choice of base fluid for heat transfer applications is an ethylene glycol or propylene glycol mixed with water in different proportions. In the present research, a 60% ethylene glycol (EG) or propylene glycol (PG) and 40% water (W) by mass fluid mixture (60:40 EG/W or 60:40 PG/W) was used as a base fluid, which provides freeze protection to a very low level of temperature. Experiments were conducted to measure the convective heat transfer coefficient and pressure loss of nanofluids flowing in a circular tube in the fully developed turbulent regime. The experimental measurements were carried out for aluminum oxide (Al2O3), copper oxide (CuO) and silicon dioxide (SiO2) nanoparticles dispersed in 60:40 EG/W base fluid. Experiments revealed that the heat transfer coefficient of nanofluids showed an increase with the particle volumetric concentration. Pressure loss was also observed to increase with the nanoparticle volumetric concentration. New correlations for the Nusselt number and the friction factor were developed. The effects of temperature and particle volumetric concentration on different thermophysical properties (e.g. viscosity, thermal conductivity, specific heat and density) and subsequently on the Prandtl number

  19. Ovine and Caprine Toxoplasmosis: Experimental Study

    Directory of Open Access Journals (Sweden)

    Shawkat Q. Lafi

    2014-01-01

    Full Text Available Eighteen mature ewes of the Mytilene breed and 18 mature Local- Damascus crossbred goats, seronegative for Toxoplasma gondii (T. gondii by ELISA were used. All animals were mated after synchronization of estrus. On day 90 of pregnancy, animals were randomly assigned to 3 experimental groups; 6 ewes (S1 and 6 goats (G1 were orally inoculated by stomach tube with 1000 oocysts; 6 ewes (S2 and 6 goats (G2 were orally inoculated with a non-infected control inoculum. On day 140+2 of pregnancy, the remaining 6 ewes (S3 and 6 goats (G3 were inoculated by stomach tube with 3000 oocysts. Positive T. godii DNA was detected in 94% of fetal and maternal blood, 95% fetal tissue, 89% pre-colostral udder secretions and 12.5% milk samples using Polymerase Chain Reaction (PCR. Infected animals and their live newborns was seropositive (ELISA until the end of the study. PCR was able to detect T. gondii DNA in maternal blood of infected animals 3-5 days before abortion occurred. This time period may be used to implement preventive and therapeutic measure to reduce abortion rate and associated economic losses. Since milk and milk products are important food sources in rural areas and in many cases it is used unpasteurized before consumption. The T. gondii DNA, detected by PCR in milk samples of infected animals, increases the possibility that the parasite is transmitted through consumption of unpasteurized milk which is a highly relevant result for public health considerations and providing valuable information for future research.

  20. Computatonal and experimental study of laminar flames

    Energy Technology Data Exchange (ETDEWEB)

    Smooke, M.D.; Long, M.B. [Yale Univ., New Haven, CT (United States)

    1993-12-01

    This research has centered on an investigation of the effects of complex chemistry and detailed transport on the structure and extinction of hydrocarbon flames in counterflow, cylindrical and coflowing axisymmetric configurations. The authors have pursued both computational and experimental aspects of the research in parallel. The computational work has focused on the application of accurate and efficient numerical methods for the solution of the one and two-dimensional nonlinear boundary value problems describing the various reacting systems. Detailed experimental measurements were performed on axisymmetric coflow flames using two-dimensional imaging techniques. In particular, spontaneous Raman scattering and laser induced fluorescence were used to measure the temperature, major and minor species profiles.

  1. Low Temperature Combustion with Thermo-Chemical Recuperation to Maximize In-Use Engine Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Nigel N. Clark; Francisco Posada; Clinton Bedick; John Pratapas; Aleksandr Kozlov; Martin Linck; Dmitri Boulanov

    2009-03-30

    The key to overcome Low Temperature Combustion (LTC) load range limitations in reciprocating engines is based on proper control over the thermo-chemical properties of the in-cylinder charge. The studied alternative to achieve the required control of LTC is the use of two separate fuel streams to regulate timing and heat release at specific operational points, where the secondary fuel is a reformed product of the primary fuel in the tank. It is proposed in this report that the secondary fuel can be produced using exhaust heat and Thermo-Chemical Recuperation (TCR). TCR for reciprocating engines is a system that employs high efficiency recovery of sensible heat from engine exhaust gas and uses this energy to transform fuel composition. The recuperated sensible heat is returned to the engine as chemical energy. Chemical conversions are accomplished through catalytic and endothermic reactions in a specially designed reforming reactor. An equilibrium model developed by Gas Technology Institute (GTI) for heptane steam reforming was applied to estimate reformed fuel composition at different reforming temperatures. Laboratory results, at a steam/heptane mole ratio less than 2:1, confirm that low temperature reforming reactions, in the range of 550 K to 650 K, can produce 10-30% hydrogen (by volume, wet) in the product stream. Also, the effect of trading low mean effective pressure for displacement to achieve power output and energy efficiency has been explored by WVU. A zerodimensional model of LTC using heptane as fuel and a diesel Compression Ignition (CI) combustion model were employed to estimate pressure, temperature and total heat release as inputs for a mechanical and thermal loss model. The model results show that the total cooling burden on an LTC engine with lower power density and higher displacement was 14.3% lower than the diesel engine for the same amount of energy addition in the case of high load (43.57mg fuel/cycle). These preliminary modeling and

  2. Experimental Study of a Thermoelectric Generation System

    DEFF Research Database (Denmark)

    Zhu, Junpeng; Gao, Junling; Chen, Min

    2011-01-01

    A flat wall-like thermoelectric generation system is developed for applications in exhaust heat of kilns. The design of the whole experimental setup is presented. The essential performance of the thermoelectric generation system is tested, including open-circuit voltage, output power, and system ...

  3. Economic principles in communication: An experimental study

    NARCIS (Netherlands)

    De Jaegher, K.; Rosenkranz, S.; Weitzel, G.U.

    2014-01-01

    This paper experimentally investigates how economic principles affect communication. In a simple sender–receiver game with common interests over payoffs, the sender can send a signal without a pre-given meaning in an infrequent or frequent state of the world. When the signal is costly, several

  4. Blast mitigation experimental and numerical studies

    CERN Document Server

    2013-01-01

    Presents experimental methods of material and structural response to dynamic blast loads Includes computational analysis of material and structural response to dynamic blast loads Offers mitigation measures for structures in various environments Relates lab experiments to larger field tests Features more than 150 illustrations

  5. An experimental study of passive regenerator geometries

    DEFF Research Database (Denmark)

    Engelbrecht, Kurt; Nielsen, Kaspar Kirstein; Pryds, Nini

    2011-01-01

    experimental uncertainty associated with magnetocaloric material properties, all regenerators are made of aluminum. The performance of corrugated plates and dimpled plates are compared to traditional flat plate regenerators for a range of cycle times and utilizations. Each regenerator is built using 18...

  6. Thermochemical sulphate reduction can improve carbonate petroleum reservoir quality

    Science.gov (United States)

    Jiang, Lei; Worden, Richard H.; Yang, Changbing

    2018-02-01

    Interest in the creation of secondary pore spaces in petroleum reservoirs has increased because of a need to understand deeper and more complex reservoirs. The creation of new secondary porosity that enhances overall reservoir quality in deeply buried carbonate reservoirs is controversial and some recent studies have concluded it is not an important phenomenon. Here we present petrography, geochemistry, fluid inclusion data, and fluid-rock interaction reaction modeling results from Triassic Feixianguan Formation, Sichuan Basin, China, core samples and explore the relative importance of secondary porosity due to thermochemical sulphate reduction (TSR) during deep burial diagenesis. We find that new secondary pores result from the dissolution of anhydrite and possibly from dissolution of the matrix dolomite. Assuming porosity before TSR was 16% and the percentage of anhydrite was 6%, modelling shows that, due to TSR, 1.6% additional porosity was created that led to permeability increasing from 110 mD (range 72-168 mD within a 95% confidence interval) to 264 mD (range 162-432 mD within a 95% confidence interval). Secondary porosity results from the density differences between reactant anhydrite and product calcite, the addition of new water during TSR, and the generation of acidity during the reaction of new H2S with the siderite component in pre-existing dolomite in the reservoir. Fluid pressure was high during TSR, and approached lithostatic pressure in some samples; this transient overpressure may have led to the maintenance of porosity due to the inhibition of compactional processes. An additional 1.6% porosity is significant for reserve calculations, especially considering that it occurs in conjunction with elevated permeability that results in faster flow rates to the production wells.

  7. EXPERIMENTAL AND THEORETICAL NMR STUDY OF 4-(1 ...

    African Journals Online (AJOL)

    Preferred Customer

    experimental and theoretical data have showed that the molecular geometry and the ... 1D and 2D hetero- and homonuclear NMR methods enable to ... The essence of this study is briefly to report experimental and theoretical NMR features of.

  8. Model refinement for offshore platforms: Experimental study

    Science.gov (United States)

    Zhang, Min; Chen, Zongli; Wu, Yanjian

    2017-08-01

    Offshore jacket platforms are widely used in offshore oil and gas exploitation. Finite element models of such structures need to have many degrees of freedom (DOFs) to represent the geometrical detail of complex structures, thereby leading to incompatibility in the number of DOFs of experimental models. To bring them both to the same order while ensuring that the essential eigen- properties of the refined model match those of experimental models, an extended model refinement procedure is presented in this paper. Vibration testing of an offshore jacket platform model is performed to validate the applicability of the proposed approach. A full-order finite element model of the platform is established and then tuned to meet the measured modal properties identified from the acceleration signals. Both model reduction and modal expansion methods are investigated, as well as various scenarios of sensor arrangements. Upon completion of the refinement, the updated jacket platform model matches the natural frequencies of the measured model well.

  9. Experimental studies of Steel Corrugated Constructions

    Directory of Open Access Journals (Sweden)

    Lazarev Yuriy

    2016-01-01

    Full Text Available The purpose of this particular article is to assess existing calculations of steel corrugated constructions. Steel Corrugated Construction is a perspective type of constructions, which is exhibiting numerous advantages in comparison with one that currently applied in automobile and railroad networks (reinforced concrete water-throughput pipes, reinforced concrete frame bridges. The evaluation of experimental data on models of constructions of this particular type has been carried out in order to improve calculations of Steel Corrugated Constructions.

  10. Thermochemical ablation therapy of VX2 tumor using a permeable oil-packed liquid alkali metal.

    Directory of Open Access Journals (Sweden)

    Ziyi Guo

    Full Text Available Alkali metal appears to be a promising tool in thermochemical ablation, but, it requires additional data on safety is required. The objective of this study was to explore the effectiveness of permeable oil-packed liquid alkali metal in the thermochemical ablation of tumors.Permeable oil-packed sodium-potassium (NaK was prepared using ultrasonic mixing of different ratios of metal to oil. The thermal effect of the mixture during ablation of muscle tissue ex vivo was evaluated using the Fluke Ti400 Thermal Imager. The thermochemical effect of the NaK-oil mixture on VX2 tumors was evaluated by performing perfusion CT scans both before and after treatment in 10 VX2 rabbit model tumors. VX2 tumors were harvested from two rabbits immediately after treatment to assess their viability using trypan blue and hematoxylin and eosin (H.E. staining.The injection of the NaK-oil mixture resulted in significantly higher heat in the ablation areas. The permeable oil controlled the rate of heat released during the NaK reaction with water in the living tissue. Perfusion computed tomography and its parameter map confirmed that the NaK-oil mixture had curative effects on VX2 tumors. Both trypan blue and H.E. staining showed partial necrosis of the VX2 tumors.The NaK-oil mixture may be used successfully to ablate tumor tissue in vivo. With reference to the controlled thermal and chemical lethal injury to tumors, using a liquid alkali in ablation is potentially an effective and safe method to treat malignant tumors.

  11. Fuel cell efficiency in a combined electrochemical-thermochemical process

    Energy Technology Data Exchange (ETDEWEB)

    Balko, E.N.; Avery, W.

    1981-01-01

    The thermodynamics of a H/sub 2//Cl/sub 2/ fuel cell combined with a thermochemical hydrogen chloride oxidation stage are considered. Such a cycle is superior to the phosphoric acid H/sub 2//O/sub 2/ systems but does not better the efficiency demonstrated in more advanced H/sub 2//O/sub 2/ fuel cell systems. 8 refs.

  12. Observations of Circumstellar Thermochemical Equilibrium: The Case of Phosphorus

    Science.gov (United States)

    Milam, Stefanie N.; Charnley, Steven B.

    2011-01-01

    We will present observations of phosphorus-bearing species in circumstellar envelopes, including carbon- and oxygen-rich shells 1. New models of thermochemical equilibrium chemistry have been developed to interpret, and constrained by these data. These calculations will also be presented and compared to the numerous P-bearing species already observed in evolved stars. Predictions for other viable species will be made for observations with Herschel and ALMA.

  13. SolarSyngas: Results from a virtual institute developing materials and key components for solar thermochemical fuel production

    Science.gov (United States)

    Roeb, Martin; Steinfeld, Aldo; Borchardt, Günter; Feldmann, Claus; Schmücker, Martin; Sattler, Christian; Pitz-Paal, Robert

    2016-05-01

    The Helmholtz Virtual Institute (VI) SolarSynGas brings together expertise from solar energy research and materials science to develop metal oxide based redox materials and to integrate them in a suitable way into related process technologies for two-step thermochemical production of hydrogen and carbon monoxide from water and CO2. One of the foci of experimental investigation was exploring the impact of doping on the feasibility of ceria-based materials - mainly by Zr-doping. The results indicate that a certain Zr-content enhances the reducibility and therefore the splitting performance. Increasing the Zr-content to x = 0.15 improved the specific CO2-splitting performance by 50% compared to pure ceria. This finding agrees with theoretical studies attributing the improvements to lattice modification caused by the introduction of Zr4+. Thermogravimetric relaxation experiments and equilibrium oxygen isotope exchange experiments with subsequent depth profiling analysis were carried out on ceria. As a result the reduction reaction of even dense samples of pure ceria with a grain size of about 20 µm is surface reaction controlled. The structure of the derived expression for the apparent activation energy suggests that the chemical surface exchange coefficient should show only a very weak dependence on temperature for ceria doped with lower valence cations. A solar receiver reactor exhibiting a foam-type reticulated porous ceramics made of ceria was tested. It could be shown that applying dual-scale porosity to those foams with mm-size pores for effective radiative heat transfer during reduction and μm-size pores within its struts for enhanced kinetics during oxidation allows enhancing the performance of the reactor significantly. Also a particle process concept applying solid-solid heat recovery from redox particles in a high temperature solar thermochemical process was analysed that uses ceramic spheres as solid heat transfer medium. This concept can be implemented

  14. Experimental study of the nucleon spin structure

    Energy Technology Data Exchange (ETDEWEB)

    Litmaath, M.F.

    1996-05-07

    After introducing the theoretical framework, which includes DIS, the Quark Parton Model (QPM) and QCD, we describe the implementation of the experiment. The SMC uses a beam of 190 GeV naturally polarized muons, scattering off nucleons in a large cryogenic target containing protons or deuterons that are polarized through Dynamic Nuclear Polarization (DNP). The target material is located in two cells in a row, with opposite polarizations. Every 5 hours the polarizations of both cells are reversed. The target polarization is measured by an NMR system. The polarization of the beam is measured in a polarimeter, located downstream of the main experimental setup. (orig.).

  15. Experimental Studies of Coaxial Plasma Gun Current

    Science.gov (United States)

    1988-09-01

    insertion into experimental systems (117-133), fueling for proposed thermonuclear reactors (134-138], breeding fissionable material [139, 140] and...Center Top Level Linear Exponential Yield Current Current Extrap . Extrap . (MA) (MA) Current Current (MA) (MA) 02901 2.8106 0.18 0.05 D3001 1.2x107...Exponential Yield Current Current Extrap . Extrap . (MA) (MA) Current Current (MA) (MA) 30703 1.610 8 1.57 0.64 0.54 0.59 J0706 4.040O 1.46 0.85 0.80 0.82 J

  16. Feasibility study of the AOSTA experimental campaign

    Directory of Open Access Journals (Sweden)

    Carta M.

    2016-01-01

    Full Text Available The reduction of the nuclear waste is one of the most important nuclear issues. The high radiotoxicity of the spent fuel is due to plutonium and some minor actinides (MAs such as neptunium, americium and curium, above all. One way to reduce their hazard is to destroy by fission MAs in appropriate nuclear reactors. To allow the MAs destruction an important effort have been done on the nuclear data due to the poor knowledge in this field. In the framework of one of the NEA Expert Group on Integral Experiments for Minor Actinide Management an analysis of the feasibility of MAs irradiation campaign in the TAPIRO fast research reactor is carried out. This paper provides preliminary results obtained by calculations modelling the irradiation, in different TAPIRO irradiation channels, of some CEA samples coming from the French experimental campaign OSMOSE, loaded with different contents of MAs, in order to access, through particular peak spectrometry, to their capture cross section. On the basis of neutron transport calculation results, obtained by both deterministic and Monte Carlo methods, an estimate of the irradiated samples counting levels from the AOSTA (Activation of OSMOSE Samples in TAPIRO experimental campaign is provided.

  17. Heterogeneous Thermochemical Decomposition Under Direct Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Lipinski, W.; Steinfeld, A. [PSI and ETH Zuerich(Switzerland)

    2005-03-01

    Radiative heat transfer in a chemical reacting system directly exposed to an external source of high-flux radiation is considered. The endothermic decomposition of CaCO{sub 3}(s) into CaO(s) and CO{sub 2}(g) is selected as the model heterogeneous reaction. Experimentation using an Ar arc as the radiation source was carried out in which powder samples were subjected to radiative power fluxes in the range 400-930 kW/m{sup 2}. A 3D transient heat transfer model that links conduction-convection-radiation heat transfer to the chemical kinetics is formulated using wavelength and chemical composition dependent material properties. Monte-Carlo ray tracing and the Rosseland diffusion approximation are employed to obtain the radiative transport. The unsteady energy equation is solved by finite volume technique. The model is validated by com-paring the computed reaction extent variation with time to the values experimentally measured. (author)

  18. Experimental study of external fuel vaporization

    Science.gov (United States)

    Szetela, E. J.; Tevelde, J. A.

    1982-01-01

    The fuel properties used in the design of a flash vaporization system for aircraft gas turbine engines were evaluated in experiments using a flowing system to determine critical temperature and pressure, boiling points, dew points, heat transfer coefficients, deposit formation rates, and deposit removal. Three fuels were included in the experiments: Jet-A, an experimental referree broad specification fuel, and a premium No. 2 diesel fuel. Engine conditions representing a NASA Energy Efficient Engine at sea-level take-off, cruise, and idle were simulated in the vaporization system and it was found that single phase flow was maintained in the heat exchanger and downstream of the throttle. Deposits encountered in the heat exchanger represented a thermal resistance as high as 1300 sq M K/watt and a deposit formation rate over 1000 gC/sq cm hr.

  19. Experimental Study of the Sampled Labyrinth Chaos

    Directory of Open Access Journals (Sweden)

    J. Petrzela

    2011-12-01

    Full Text Available In this paper, some new numerical as well as experimental results connected with the so-called labyrinth chaos are presented. This very unusual chaotic motion can be generated by mathematical model involving the scalar goniometrical functions which makes a three-dimensional autonomous dynamical system strongly nonlinear. Final circuitry implementation with analog core and digital parts can be used for modeling Brownian motion. From the viewpoint of generating chaotic motion by some electronic circuit, first step is to solve problems associated with the two-port nonlinear transfer functions synthesis. In the case of labyrinth chaos the finite dynamical range of the input variables introduced by the used active elements usually limits the performance greatly, similarly as it holds for the multi-grid spiral attractors. This paper shows an elegant way how to remove these obstacles by using uni-versal multiple-port with internal digital signal processing.

  20. Experimental Study of Pollutant Transfer within Dwellings

    CERN Document Server

    Koffi, Juslin; Allard, Francis; Husaunndee, Ahmad

    2010-01-01

    A mechanical ventilation principle used in French residential buildings was tested in the experimental house of the CSTB research centre. The experiments dealt with pollutant removal efficiency of this ventilation principle, mainly with air tightness and the influence of internal doors. Tracer gas constant injection method was used to simulate the pollution source in the living room. SF6 concentrations were measured in several rooms. The results showed that the air flow routes were in agreement with the theory as long as internal doors were closed. When doors were open, the air pattern was disturbed a lot; a great quantity of the emitted pollutant was measured in the bedrooms. Besides, stack effect promotes the pollutant moving towards the bedrooms under higher indoor-outdoor air temperature differences. In addition, the results showed that if the opening of the bedroom window increases the air change rate, it does not guarantee a good indoor air quality.

  1. Computational and experimental study of laminar flames

    Energy Technology Data Exchange (ETDEWEB)

    Smooke, Mitchell [Yale Univ., New Haven, CT (United States)

    2015-05-29

    During the past three years, our research has centered on an investigation of the effects of complex chemistry and detailed transport on the structure and extinction of hydrocarbon flames in coflowing axisymmetric configurations. We have pursued both computational and experimental aspects of the research in parallel on both steady-state and time-dependent systems. The computational work has focused on the application of accurate and efficient numerical methods for the solution of the steady-state and time-dependent boundary value problems describing the various reacting systems. Detailed experimental measurements were performed on axisymmetric coflow flames using two-dimensional imaging techniques. Previously, spontaneous Raman scattering, chemiluminescence, and laser-induced fluorescence were used to measure the temperature, major and minor species profiles. Particle image velocimetry (PIV) has been used to investigate velocity distributions and for calibration of time-varying flames. Laser-induced incandescence (LII) with an extinction calibration was used to determine soot volume fractions, while soot surface temperatures were measured with three-color optical pyrometry using a color digital camera. A blackbody calibration of the camera allows for determination of soot volume fraction as well, which can be compared with the LII measurements. More recently, we have concentrated on a detailed characterization of soot using a variety of techniques including time-resolved LII (TiRe-LII) for soot primary particles sizes, multi-angle light scattering (MALS) for soot radius of gyration, and spectrally-resolved line of sight attenuation (spec-LOSA). Combining the information from all of these soot measurements can be used to determine the soot optical properties, which are observed to vary significantly depending on spatial location and fuel dilution. Our goal has been to obtain a more fundamental understanding of the important fluid dynamic and chemical interactions in

  2. Thermochemical Conversion of Biomass to Fuels and Chemicals - Pyrolysis and Gasification

    OpenAIRE

    Mante, Nii Ofei

    2011-01-01

    The development of advance thermochemical technologies is critical for sustainable production of affordable biofuel, biopower and bioproduct from biomass. Thermochemical conversion processes are flexible and independent of feedstock. Currently, pyrolysis and gasification are promising thermochemical conversion processes that use heat and chemistry to produce bio-oil, syngas, bio-char and chemicals from a wide spectrum of biomass feedstocks, varying from woody and herbaceous biomass to ...

  3. Thermochemical analysis of intermolecular interactions between N-acetylglycine and polyols in aqueous solutions

    Science.gov (United States)

    Mezhevoi, I. N.; Badelin, V. G.

    2017-05-01

    The integral enthalpies of dissolution Δsol H m for N-acetylglycine in aqueous solutions of glycerol, ethylene glycol and 1,2-propylene glycol are measured via solution calorimetry. The standard enthalpies of dissolution (Δsol H 0) and transfer (Δtr H 0) for N-acetylglycine from water to aqueous solutions of polyhydric alcohols are calculated from experimental data. Positive values of enthalpy coefficients of pair interactions h xy for amino acids and polyol molecules are calculated using the McMillan-Mayer theory. The results are discussed using an approach for evaluating different types of interactions in ternary systems and the effect the structural features of interacting biomolecules have on the thermochemical characteristics of N-acetylglycine dissolution.

  4. Synthesis and design of optimal biorefinery using an expanded network with thermochemical and biochemical biomass conversion platforms

    DEFF Research Database (Denmark)

    Cheali, Peam; Gernaey, Krist; Sin, Gürkan

    2013-01-01

    This study presents the development of an expanded biorefinery processing network for producing biofuels that combines biochemical and thermochemical conversion platforms. The expanded network is coupled to a framework that uses a superstructure based optimization approach to generate and compare...... of 72 processing intervals . This superstructure was integrated with an earlier developed superstructure for biochemical conversion routes thereby forming a formidable number of biorefinery alternatives. The expanded network was demonstrated to be versatile and useful as a decision support tool...

  5. Dehydrogenation of N{sub 2}H{sub X} (X = 2 − 4) by nitrogen atoms: Thermochemical and kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Spada, Rene Felipe Keidel; Araujo Ferrão, Luiz Fernando de [Departamento de Química, Instituto Tecnológico de Aeronáutica, São José dos Campos 12.228-900, São Paulo (Brazil); Departamento de Física, Instituto Tecnológico de Aeronáutica, São José dos Campos 12.228-900, São Paulo (Brazil); Roberto-Neto, Orlando [Divisão de Aerotermodinâmica e Hipersônica, Instituto de Estudos Avançados, São José dos Campos 12.229-840, São Paulo (Brazil); Machado, Francisco Bolivar Correto, E-mail: fmachado@ita.br [Departamento de Química, Instituto Tecnológico de Aeronáutica, São José dos Campos 12.228-900, São Paulo (Brazil)

    2013-11-21

    Thermochemical and kinetics of sequential hydrogen abstraction reactions from hydrazine by nitrogen atoms were studied. The dehydrogenation was divided in three steps, N{sub 2}H{sub 4} + N, N{sub 2}H{sub 3} + N, and N{sub 2}H{sub 2} + N. The thermal rate constants were calculated within the framework of canonical variational theory, with zero and small curvature multidimensional tunnelling corrections. The reaction paths were computed with the BB1K/aug-cc-pVTZ method and the thermochemical properties were improved with the CCSD(T)/CBS//BB1K/aug-cc-pVTZ approach. The first dehydrogenation step presents the lowest rate constants, equal to 1.22 × 10{sup −20} cm{sup 3} molecule{sup −1} s{sup −1} at 298 K.

  6. Experimental study on HVAC sound parameters

    Science.gov (United States)

    Bujoreanu, C.; Benchea, M.

    2016-08-01

    HVAC system represent major source of buildings internal noise and therefore they are designed to provide a human acoustic comfort besides the thermal and air quality requirements. The paper experimentally investigates three types of commercial air handler units (AHU) with different ducts cross-section sizes and inlet-outlet configuration. The measurements are performed in an anechoic room. The measurements are carried out at different fan's speeds, ranging the power-charge from 30-100% while the duct air flow is slowly adjusted from full open to full closed, between 0-500 Pa. The sound pressure levels of the radiant units are rated using NR curves. Also, the supply and the outdoor ducts sound levels are compared in order to point the frequencies where the noise must be reduced. Third-octave band analysis of random noise of an air handling unit from a HVAC system is realized, using measurement procedures that agrees the requirements of the ISO 3744:2011 and ISO 5136:2010 standards. The comparatively results highlight the effects of the geometry, air flow pressure and power-charging dependencies upon the sound level. This is the start for a noise reduction strategy.

  7. Experimental study of asymmetric heart valve prototype

    Science.gov (United States)

    Vukicevic, M.; Fortini, S.; Querzoli, G.; Cenedese, A.; Pedrizzetti, G.

    2011-11-01

    The mechanical heart valves (MHVs) are extremely important medical devices, commonly used for diseased heart valves replacement. Despite the long term of use and constant design refinement, the MHVs are very far from ideal and their performance is very diverse from that of the native ones. It has been approved that small variations in geometry of valvular leaflets influence the significant change in the intraventricular vortical flow, known as one of the most important factors for the overall functionality of the heart. We have experimentally examined the home-made heart valve prototypes, exclusively modeled for the mitral valve replacement. The performance and energetic properties of the prototypes have been compared with those in the presence of standard MHVs. The analysis was based on the testing of intraventricular fluid dynamics, usually missing criteria for the quality of the valve performance. It has been shown that the asymmetric prototype, with unequal leaflets and D-shaped orifice produces flow patterns and energetic properties close to those found in the healthy subjects. Thus, the break of symmetry in the standard bi-leaflet MHV prosthesis, at least from the fluid dynamics point of view, is worthwhile to be considered for the design of MHVs for the mitral valve replacement.

  8. Production of activated carbon by waste tire thermochemical degradation with CO2.

    Science.gov (United States)

    Betancur, Mariluz; Martínez, Juan Daniel; Murillo, Ramón

    2009-09-15

    The thermochemical degradation of waste tires in a CO(2) atmosphere without previous treatment of devolatilization (pyrolysis) in order to obtain activated carbons with good textural properties such as surface area and porosity was studied. The operating variables studied were CO(2) flow rate (50 and 150 mL/min), temperature (800 and 900 degrees C) and reaction time (1, 1.5, 2, 2.5 and 3h). Results show a considerable effect of the temperature and the reaction time in the porosity development. Kinetic measurements showed that the reactions involved in the thermochemical degradation of waste tire with CO(2), are similar to those developed in the pyrolysis process carried out under N(2) atmosphere and temperatures below 760 degrees C, for particles sizes of 500 microm and heating rate of 5 degrees C/min. For temperatures higher than 760 degrees C the CO(2) starts to oxidize the remaining carbon black. Activated carbon with a 414-m(2)/g surface area at 900 degrees C of temperature, 150 mL/min of CO(2) volumetric flow and 180 min of reaction time was obtained. In this work it is considering the no reactivity of CO(2) for devolatilization of the tires (up to 760 degrees C), and also the partial oxidation of residual char at high temperature for activation (>760 degrees C). It is confirmed that there are two consecutive stages (devolatilization and activation) developed from the same process.

  9. Economic principles in communication: an experimental study.

    Science.gov (United States)

    De Jaegher, Kris; Rosenkranz, Stephanie; Weitzel, Utz

    2014-12-21

    This paper experimentally investigates how economic principles affect communication. In a simple sender-receiver game with common interests over payoffs, the sender can send a signal without a pre-given meaning in an infrequent or frequent state of the world. When the signal is costly, several theories (focal point theory, the intuitive criterion, evolutionary game theory) predict an efficient separating equilibrium, where the signal is sent in the infrequent state of the world (also referred to as Horn׳s rule). To analyze whether Horn׳s rule applies, and if so, which theory best explains it, we develop and test variants of the sender-receiver game where the theories generate discriminatory hypotheses. In costly signaling variants, our participants follow Horn׳s rule most of the time, in a manner that is best explained by focal point theory. In costless signaling variants, evolutionary game theory best explains our results. Here participants coordinate significantly more (less) often on a separating equilibrium where the signal is sent in the frequent state if they are primed to associate the absence of a signal with the infrequent (frequent) state of the world. We also find indications that a similar priming effect applies to costly signals. Thus, while the frequency with which participants follow Horn׳s rule in costly signaling variants is best explained by Horn׳s rule, the priming effect shows that some of our participants׳ behavior is best explained by evolutionary game theory even when signals are costly. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Theoretical & Experimental Studies of Elementary Particles

    Energy Technology Data Exchange (ETDEWEB)

    McFarland, Kevin [Univ. of Rochester, NY (United States)

    2012-10-04

    Abstract High energy physics has been one of the signature research programs at the University of Rochester for over 60 years. The group has made leading contributions to experimental discoveries at accelerators and in cosmic rays and has played major roles in developing the theoretical framework that gives us our ``standard model'' of fundamental interactions today. This award from the Department of Energy funded a major portion of that research for more than 20 years. During this time, highlights of the supported work included the discovery of the top quark at the Fermilab Tevatron, the completion of a broad program of physics measurements that verified the electroweak unified theory, the measurement of three generations of neutrino flavor oscillations, and the first observation of a ``Higgs like'' boson at the Large Hadron Collider. The work has resulted in more than 2000 publications over the period of the grant. The principal investigators supported on this grant have been recognized as leaders in the field of elementary particle physics by their peers through numerous awards and leadership positions. Most notable among them is the APS W.K.H. Panofsky Prize awarded to Arie Bodek in 2004, the J.J. Sakurai Prizes awarded to Susumu Okubo and C. Richard Hagen in 2005 and 2010, respectively, the Wigner medal awarded to Susumu Okubo in 2006, and five principal investigators (Das, Demina, McFarland, Orr, Tipton) who received Department of Energy Outstanding Junior Investigator awards during the period of this grant. The University of Rochester Department of Physics and Astronomy, which houses the research group, provides primary salary support for the faculty and has waived most tuition costs for graduate students during the period of this grant. The group also benefits significantly from technical support and infrastructure available at the University which supports the work. The research work of the group has provided educational opportunities

  11. Characterisation of agroindustrial solid residues as biofuels and potential application in thermochemical processes.

    Science.gov (United States)

    Virmond, Elaine; De Sena, Rennio F; Albrecht, Waldir; Althoff, Christine A; Moreira, Regina F P M; José, Humberto J

    2012-10-01

    In the present work, selected agroindustrial solid residues from Brazil - biosolids from meat processing wastewater treatment and mixture of sawdust with these biosolids; residues from apple and orange juice industries; sugarcane bagasse; açaí kernels (Euterpe oleracea) and rice husk - were characterised as solid fuels and an evaluation of their properties, including proximate and ultimate composition, energy content, thermal behaviour, composition and fusibility of the ashes was performed. The lower heating value of the biomasses ranged from 14.31 MJkg(-1) to 29.14 MJkg(-1), on a dry and ash free basis (daf), all presenting high volatile matter content, varying between 70.57 wt.% and 85.36 wt.% (daf) what improves the thermochemical conversion of the solids. The fouling and slagging tendency of the ashes was predicted based on the fuel ash composition and on the ash fusibility correlations proposed in the literature, which is important to the project and operation of biomass conversion systems. The potential for application of the Brazilian agroindustrial solid residues studied as alternative energy sources in thermochemical processes has been identified, especially concerning direct combustion for steam generation. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. Effect of thermal, chemical and thermo-chemical pre-treatments to enhance methane production

    Energy Technology Data Exchange (ETDEWEB)

    Rafique, Rashad; Nizami, Abdul-Sattar; Murphy, Jerry D.; Kiely, Gerard [Department of Civil and Environmental Engineering, University College Cork (Ireland); Poulsen, Tjalfe Gorm [Department of Biotechnology, Chemistry and Environmental Engineering, Aalborg University (Denmark); Asam, Zaki-ul-Zaman [Department of Civil Engineering, National University of Ireland Galway (Ireland)

    2010-12-15

    The rise in oil price triggered the exploration and enhancement of various renewable energy sources. Producing biogas from organic waste is not only providing a clean sustainable indigenous fuel to the number of on-farm digesters in Europe, but also reducing the ecological and environmental deterioration. The lignocellulosic substrates are not completely biodegraded in anaerobic digesters operating at commercial scale due to their complex physical and chemical structure, which result in meager energy recovery in terms of methane yield. The focus of this study is to investigate the effect of pre-treatments: thermal, thermo-chemical and chemical pre-treatments on the biogas and methane potential of dewatered pig manure. A laboratory scale batch digester is used for these pre-treatments at different temperature range (25 C-150 C). Results showed that thermo-chemical pretreatment has high effect on biogas and methane potential in the temperature range (25-100 C). Maximum enhancement is observed at 70 C with increase of 78% biogas and 60% methane production. Thermal pretreatment also showed enhancement in the temperature range (50-10 C), with maximum enhancement at 100 C having 28% biogas and 25% methane increase. (author)

  13. Ab Initio Computations and Active Thermochemical Tables Hand in Hand: Heats of Formation of Core Combustion Species.

    Science.gov (United States)

    Klippenstein, Stephen J; Harding, Lawrence B; Ruscic, Branko

    2017-09-07

    The fidelity of combustion simulations is strongly dependent on the accuracy of the underlying thermochemical properties for the core combustion species that arise as intermediates and products in the chemical conversion of most fuels. High level theoretical evaluations are coupled with a wide-ranging implementation of the Active Thermochemical Tables (ATcT) approach to obtain well-validated high fidelity predictions for the 0 K heat of formation for a large set of core combustion species. In particular, high level ab initio electronic structure based predictions are obtained for a set of 348 C, N, O, and H containing species, which corresponds to essentially all core combustion species with 34 or fewer electrons. The theoretical analyses incorporate various high level corrections to base CCSD(T)/cc-pVnZ analyses (n = T or Q) using H2, CH4, H2O, and NH3 as references. Corrections for the complete-basis-set limit, higher-order excitations, anharmonic zero-point energy, core-valence, relativistic, and diagonal Born-Oppenheimer effects are ordered in decreasing importance. Independent ATcT values are presented for a subset of 150 species. The accuracy of the theoretical predictions is explored through (i) examination of the magnitude of the various corrections, (ii) comparisons with other high level calculations, and (iii) through comparison with the ATcT values. The estimated 2σ uncertainties of the three methods devised here, ANL0, ANL0-F12, and ANL1, are in the range of ±1.0-1.5 kJ/mol for single-reference and moderately multireference species, for which the calculated higher order excitations are 5 kJ/mol or less. In addition to providing valuable references for combustion simulations, the subsequent inclusion of the current theoretical results into the ATcT thermochemical network is expected to significantly improve the thermochemical knowledge base for less-well studied species.

  14. EXPERIMENTAL STUDY OF CARRYING CAPACITY GLULAM BEAMS, REINFORCED SPECIAL WAY

    Directory of Open Access Journals (Sweden)

    O. M. Ustarkhanov

    2013-01-01

    Full Text Available The paper deals a new structural solution of reinforced glued wooden beam and results ofexperimental studies of the bearing capacity of reinforced beams in a special way. We presentthedesign parameters ofprototypebeams, description ofthe experimental setup, results of experimental studies and comparative analysis ofthe stresses anddeflectionsdepending on how the pinching inclined armature.

  15. Experimental studies of auroral arc generators

    Energy Technology Data Exchange (ETDEWEB)

    Suszcynsky, D.M.; Borovsky, J.E.; Thomsen, M.F. [and others

    1997-08-01

    This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). An all-sky video camera system was deployed in Eagle, Alaska at the foot of the magnetic field line that threads geosynchronous satellite 1989-046 as part of a campaign to study correlations of ground-based auroral activity with satellite-based plasma and energetic particle measurements. The overall intent of the project was to study magnetosphere-ionosphere coupling as it relates to the aurora, and, in particular, to look for signatures that may help to identify various auroral generator mechanism(s). During this study, our efforts were primarily directed towards identifying the generator mechanism(s) for pulsating aurora. Our data, though not conclusive, are found to support theories that propose a cyclotron resonance mechanism for the generation of auroral pulsations.

  16. Experimental studies of actinides in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Reavis, J.G.

    1985-06-01

    This review stresses techniques used in studies of molten salts containing multigram amounts of actinides exhibiting intense alpha activity but little or no penetrating gamma radiation. The preponderance of studies have used halides because oxygen-containing actinide compounds (other than oxides) are generally unstable at high temperatures. Topics discussed here include special enclosures, materials problems, preparation and purification of actinide elements and compounds, and measurements of various properties of the molten volts. Property measurements discussed are phase relationships, vapor pressure, density, viscosity, absorption spectra, electromotive force, and conductance. 188 refs., 17 figs., 6 tabs.

  17. Thermochemical micro imprinting of single-crystal diamond surface using a nickel mold under high-pressure conditions

    Energy Technology Data Exchange (ETDEWEB)

    Imoto, Yuji; Yan, Jiwang, E-mail: yan@mech.keio.ac.jp

    2017-05-15

    Graphical abstract: A Ni mold and thermochemically imprinted microstructures on diamond. - Highlights: • A thermochemical method for micro machining/patterning of diamond is proposed. • Various kinds of microstructures were imprinted on diamond using a Ni mold. • A graphite layer is formed during imprinting which can be removed by acid. • The processing depth depends strongly on pressure and temperature. - Abstract: Single-crystal diamond is an important material for cutting tools, micro electro mechanical systems, optical devices, and semiconductor substrates. However, the techniques for producing microstructures on diamond surface with high efficiency and accuracy have not been established. This paper proposes a thermochemical imprinting method for transferring microstructures from a nickel (Ni) mold onto single-crystal diamond surface. The Ni mold was micro-structured by a nanoindenter and then pressed against the diamond surface under high temperature and pressure in argon atmosphere. Results show that microstructures on the Ni mold were successfully transferred onto the diamond surface, and their depth increased with both pressure and temperature. Laser micro-Raman spectroscopy, transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS) analyses indicate that a graphite layer was formed over the contact area between diamond and Ni during pressing, and after washing by a mixed acid, the graphite layer could be completely removed. This study demonstrated the feasibility of a cost-efficient fabrication method for large-area microstructures on single-crystal diamond.

  18. Experimental Study on Gastric Juice Secretion by ...

    African Journals Online (AJOL)

    管理平台

    2012-05-29

    May 29, 2012 ... reduced (P < 0.05) when acupuncture at zusanli was applied after treatment with cimetidine. Therefore, our study shows that when electroacupuncture at zusanli is applied, the gastric electrical frequency increased and gastric electrical amplitude reduced, while the flux of gastric juice secretion increased.

  19. Experimental and computational studies of polar solvation

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    Many articles and papers were published; a few are still in preparation or will be published. The solvation dynamics studies will be extended to ionic solutions. Computer simulations were also performed. A new line of research was begun on excited-state proton-transfer reactions catalyzed by alcohol solvents. (DLC)

  20. Experimental study of highly viscous impinging jets

    Energy Technology Data Exchange (ETDEWEB)

    Gomon, M. [Univ. of Texas, Austin, TX (United States). Dept. of Mechanical Engineering

    1998-12-01

    The objective of this research is to study the behavior of highly viscous gravity-driven jets filling a container. Matters of interest are the formation of voids in the fluid pool during the filling process and the unstable behavior of the fluid in the landing region which manifests itself as an oscillating motion. The working fluids used in this research are intended to simulate the flow behavior of molten glass. Qualitative and quantitative results are obtained in a parametric study. The fraction of voids present in the fluid pool after the filling of the container is measured for different parameter values of viscosity and mass flow rate. Likewise, frequencies of the oscillating jet are measured. Results are inconclusive with regard to a correlation between parameter settings and void fractions. As for frequencies, power law correlations are established.

  1. Experimental Study of Flow in a Bifurcation

    Science.gov (United States)

    Fresconi, Frank; Prasad, Ajay

    2003-11-01

    An instability known as the Dean vortex occurs in curved pipes with a longitudinal pressure gradient. A similar effect is manifest in the flow in a converging or diverging bifurcation, such as those found in the human respiratory airways. The goal of this study is to characterize secondary flows in a bifurcation. Particle image velocimetry (PIV) and laser-induced fluorescence (LIF) experiments were performed in a clear, plastic model. Results show the strength and migration of secondary vortices. Primary velocity features are also presented along with dispersion patterns from dye visualization. Unsteadiness, associated with a hairpin vortex, was also found at higher Re. This work can be used to assess the dispersion of particles in the lung. Medical delivery systems and pollution effect studies would profit from such an understanding.

  2. Experimental studies in non-equilibrium physics

    Science.gov (United States)

    Cressman, John Robert, Jr.

    This work is a collection of three experiments aimed at studying different facets of non-equilibrium dynamics. Chapter I concerns strongly compressible turbulence, which turns out to be very different from incompressible turbulence. The focus is on the dispersion of contaminants in such a flow. This type of turbulence can be studied, at very low mach number, by measuring the velocity fields of particles that float on a turbulently stirred body of water. It turns out that in the absence of incompressibility, the turbulence causes particles to cluster rather than to disperse. The implications of the observations are far reaching and include the transport of pollutants on the oceans surface, phytoplankton growth, as well as industrial applications. Chapter II deals with the effects of polymer additives on drag reduction and turbulent suppression, a well-known phenomenon that is not yet understood. In an attempt to simplify the problem, the effects of a polymer additive were investigated in a vortex street formed in a flowing soap film. Measurements suggest that an increase in elongational viscosity is responsible for a substantial reduction in periodic velocity fluctuations. This study also helps to illuminate the mechanism responsible for vortex separation in the wake of a bluff body. Chapter III describes an experiment designed to test a theoretical approach aimed at generalizing the classical fluctuation dissipation theorem (FDT). This theorem applies to systems driven only slightly away from thermal equilibrium, whereas ours, a liquid crystal under-going electroconvection, is so strongly driven, that the FDT does not apply. Both theory and experiment focus on the flux in global power fluctuations. Physical limitations did not permit a direct test of the theory, however it was possible to establish several interesting characteristics of the system: the source of the fluctuations is the transient defect structures that are generated when the system is driven hard

  3. An experimental study of rip channel flow

    DEFF Research Database (Denmark)

    Drønen, Nils Kjetil; Karunarathna, H.; Fredsøe, Jørgen

    2002-01-01

    A laboratory study of the flow over a bar with a single rip channel has been performed. First, the well-known pattern of a bar circulation cell with a strong offshore-directed current out through the rip channel and a weaker onshore-directed return flow over the bar is documented. Then measurements...... of the three-dimensional structure of the flow in the area where the rip channel, the bar and the trough meet and well inside the rip channel are presented. These measurements reveal that 3D effects play an important role, and that a depth-integrated viewpoint may not always be sufficient for predicting...

  4. Experimental Study of Methane Hydrates in Coal

    Directory of Open Access Journals (Sweden)

    Smirnov Vyacheslav

    2017-01-01

    Full Text Available The possibility of gas hydrate formation in porous space of coal has been studied. The experiments conducted have proven the possibility of methane gas hydrate formation in moist coal. It has been demonstrated that the decomposition points of methane gas hydrates in coal are near to the phase equilibrium curve for bulk methane hydrate. Only part of water absorbed by coal can be involved in the methane gas hydrate formation. With the increase in gas pressure increases the amount of gas hydrate formed in natural coal. For formation of hydrates at a positive temperature, the pressure in the system has to be at least 2 MPa. At the same time the speed of formation and decomposition of gas hydrates in coal is big enough.

  5. Experimental techniques for cement hydration studies

    Directory of Open Access Journals (Sweden)

    Andreas Luttge

    2011-10-01

    Full Text Available Cement hydration kinetics is a complex problem of dissolution, nucleation and growth that is still not well understood, particularly in a quantitative way. While cement systems are unique in certain aspects they are also comparable to natural mineral systems. Therefore, geochemistry and particularly the study of mineral dissolution and growth may be able to provide insight and methods that can be utilized in cement hydration research. Here, we review mainly what is not known or what is currently used and applied in a problematic way. Examples are the typical Avrami approach, the application of Transition State Theory (TST to overall reaction kinetics and the problem of reactive surface area. Finally, we suggest an integrated approach that combines vertical scanning interferometry (VSI with other sophisticated analytical techniques such as atomic force microscopy (AFM and theoretical model calculations based on a stochastic treatment.

  6. ESP Teaching for Tourism. An Experimental Study

    Directory of Open Access Journals (Sweden)

    Buzarna-Tihenea (Gălbează Alina

    2017-01-01

    Full Text Available This paper is focused on those teaching and learning methods and techniques which can improve the practical use of English for work-related purposes, this giving the students the opportunity to develop their language skills by means of attractive, motivating and useful learning activities. The paper aims at providing an in-depth knowledge about ways of studying and applying English for Specific Purposes in the Tourism field, as well as types of activities to be used in the classroom in order to assist learners overcome language difficulties. It is of great importance to emphasize the specific tasks and strategies used while teaching ESP for Tourism classes, strategies that differ from the ones used in a traditional English language classroom. The main purpose of all these ESP methods and approaches is to prepare students for their future jobs so that they can perform effectively in their area of work.

  7. Experimental Study of Liquid Fuel Spray Combustion

    DEFF Research Database (Denmark)

    Westlye, Fredrik Ree

    by the Danish Council for Strategic Research. Other supporters of the project have been MAN Diesel & Turbo A/S, DTU Mechanical Engineering, DTU Chemical Engineering, Sandia National Laboratories USA, Norwegian University of Science & Technology (NTNU) and University of Nottingham, Malaysia Campus....... The continuing stringency of emission regulations for marine diesel engines forces a deeper understanding of the complex physical processes occurring inside the engine cylinder. A deeper understanding can lead to higher accuracy of predictive numerical models, thereby enabling evaluation of multiple engine...... the specific physical quantities needed in CFD validation of these types of flames. This work is a testament to that fact. The first part of this thesis is an extensive study of optical combustion diagnostics applied to complex transient sprayflames in a high temperature and pressure environment...

  8. Flapless implant surgery: an experimental study.

    Science.gov (United States)

    Jeong, Seung-Mi; Choi, Byung-Ho; Li, Jingxu; Kim, Han-Sung; Ko, Chang-Yong; Jung, Jae-Hyung; Lee, Hyeon-Jung; Lee, Seoung-Ho; Engelke, Wilfried

    2007-07-01

    The purpose of this study was to examine the effect of flapless implant surgery on crestal bone loss and osseointegration in a canine mandible model. In 6 mongrel dogs, bilateral, edentulated, flat alveolar ridges were created in the mandible. After 3 months of healing, 2 implants in each side were placed by either flap or flapless procedures. After a healing period of 8 weeks, microcomputerized tomography at the implantation site was performed. Osseointegration was calculated as percentage of implant surface in contact with bone. Additionally, bone height was measured in the peri-implant bone. The mean osseointegration was greater at flapless sites (70.4%) than at sites with flaps (59.5%) (P flapless sites (10.1 mm) than at sites with flaps (9.0 mm) (P Flapless surgery can achieve results superior to surgery with reflected flaps. The specific improvements of this technique include enhanced osseointegration of dental implants and increased bone height.

  9. Preliminary experimental studies of waste coal gasification

    Energy Technology Data Exchange (ETDEWEB)

    Su, S.; Jin, Y.G.; Yu, X.X.; Worrall, R. [CSIRO, Brisbane, QLD (Australia). Advanced Coal Technology

    2013-07-01

    Coal mining is one of Australia's most important industries. It was estimated that coal washery rejects from black coal mining was approximately 1.82 billion tonnes from 1960 to 2009 in Australia, and is projected to produce another one billion tonnes by 2018 at the current production rate. To ensure sustainability of the Australian coal industry, we have explored a new potential pathway to create value from the coal waste through production of liquid fuels or power generation using produced syngas from waste coal gasification. Consequently, environmental and community impacts of the solid waste could be minimized. However, the development of an effective waste coal gasification process is a key to the new pathway. An Australian mine site with a large reserve of waste coal was selected for the study, where raw waste coal samples including coarse rejects and tailings were collected. After investigating the initial raw waste coal samples, float/sink testing was conducted to achieve a desired ash target for laboratory-scale steam gasification testing and performance evaluation. The preliminary gasification test results show that carbon conversions of waste coal gradually increase as the reaction proceeds, which indicates that waste coal can be gasified by a steam gasification process. However, the carbon conversion rates are relatively low, only reaching to 20-30%. Furthermore, the reactivity of waste coal samples with a variety of ash contents under N{sub 2}/air atmosphere have been studied by a home-made thermogravimetric analysis (TGA) apparatus that can make the sample reach the reaction temperature instantly.

  10. Experimental and clinical studies with intraoperative radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Sindelar, W.F.; Kinsella, T.; Tepper, J.; Travis, E.L.; Rosenberg, S.A.; Glatstein, E.

    1983-09-01

    Studies of normal tissue tolerance to intraoperative radiotherapy were done upon 65 dogs subjected to laparotomy and 11 million electron volt electron irradiation in doses ranging from zero to 5,000 rads. Results of studies indicated that intact aorta and vena cava tolerate up to 5,000 rads without loss of structural integrity. Ureteral fibrosis and stenosis develop at doses of 3,000 rads or more. Arterial anastomoses heal after doses of 4,500 rads, but fibrosis can lead to occlusion. Intestinal suture lines heal after doses of 4,500 rads. Bile duct fibrosis and stenosis develop at doses of 2,000 rads or more. Biliary-enteric anastomoses fail to heal at any dose level. A clinical trial of intraoperative radiotherapy combined with radical surgery was performed upon 20 patients with advanced malignant tumors which were considered unlikely to be cured by conventional therapies and which included carcinomas of the stomach, carcinomas of the pancreas, carcinomas involving the hilus of the liver, retroperitoneal sarcomas and osteosarcomas of the pelvis. All patients underwent resection of gross tumor, followed by intraoperative irradiation of the tumor bed and regional nodal basins. Some patients received additional postoperative external beam radiotherapy. Treatment mortality for combined operation and radiotherapy occurred in four of 20 patients. Postoperative complications occurred in four of the 16 surviving patients. Local tumor control was achieved in 11 of the 16 surviving patients, with an over-all median follow-up period of 18 months. The clinical trial suggested that intraoperative radiotherapy is a feasible adjunct to resection in locally advanced tumors, that the resulting mortality and morbidity is similar to that expected from operation alone and that local tumor control may be improved.

  11. Experimental study of forearm compartmental pressures.

    Science.gov (United States)

    Ardolino, Antonella; Zeineh, Nedal; O'Connor, David

    2010-10-01

    Chronic compartment syndrome is well recognized, although it is rare in the forearm. Diagnosis is based on history, clinical examination, and compartment pressure readings. Existing normal pressure ranges for the forearm are based on lower limb measurements. This study aimed to establish normal pre- and post-exercise forearm compartment pressures. Using a Stryker intracompartmental pressure monitor (Stryker, Kalamazoo, MI), 41 volunteers had pressure measurements of the extensor and flexor forearm compartments before and after exercise. Normal ranges were established for pre-exercise extensor compartment (2-27 mm Hg; upper confidence interval [CI] 18.8-25.2 mm Hg), post-exercise extensor compartment (2-24 mm Hg; upper CI 16.8-22.8 mm Hg), pre-exercise flexor compartment (1-19 mm Hg; upper CI 13.3-17.4 mm Hg), and post-exercise flexor compartment (0-19 mm Hg; upper CI 16-21.4 mm Hg) pressures. No significant difference was found between pressures before and after exercise. There was no correlation between whether pressures increased or decreased following exercise. There was a significant gender difference. Normal ranges were 0 to 25.2 mm Hg for the extensor compartment and 0 to 21.4 mm Hg for the flexor compartment. This study has shown a significant difference in normal forearm compartment pressures between genders. A normal reference range of flexor and extensor forearm compartment pressures to aid diagnosis of chronic compartment syndrome has been determined. This might also prove useful in aiding the diagnosis of acute forearm compartment syndrome. Copyright © 2010 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

  12. Methane-methanol cycle for the thermochemical production of hydrogen

    Science.gov (United States)

    Dreyfuss, Robert M.; Hickman, Robert G.

    1976-01-01

    A thermochemical reaction cycle for the generation of hydrogen from water comprising the following sequence of reactions wherein M represents a metal: CH.sub.4 + H.sub.2 O .fwdarw. CO + 3H.sub.2 (1) co + 2h.sub.2 .fwdarw. ch.sub.3 oh (2) ch.sub.3 oh + so.sub.2 + mo .fwdarw. mso.sub.4 + ch.sub.4 (3) mso.sub.4 .fwdarw. mo + so.sub.2 + 1/2o.sub.2 (4) the net reaction is the decomposition of water into hydrogen and oxygen.

  13. Preparation of different carbon materials by thermochemical conversion of Lignin

    Directory of Open Access Journals (Sweden)

    Juana Maria Rosas

    2014-12-01

    Full Text Available Lignin valorization plays a crucial role within the modern biorefinery scheme from both the economic and environmental points of view; and the structure and composition of lignin becomes it an ideal precursor for the preparation of advanced carbon materials with high added-value. This review provides an overview of the different carbonaceous materials obtained by thermochemical conversion of lignin, such as activated carbons, carbon fibers, template carbons; high ordered carbons; giving information about the new strategies in terms of the preparation method and their possible applications.

  14. Preparation of different carbon materials by thermochemical conversion of Lignin

    Science.gov (United States)

    Rosas, Juana; Berenguer, Raul; Valero-Romero, Maria; Rodriguez-Mirasol, Jose; Cordero, Tomás

    2014-12-01

    Lignin valorization plays a crucial role within the modern biorefinery scheme from both the economic and environmental points of view; and the structure and composition of lignin becomes it an ideal precursor for the preparation of advanced carbon materials with high added-value. This review provides an overview of the different carbonaceous materials obtained by thermochemical conversion of lignin, such as activated carbons, carbon fibers, template carbons; high ordered carbons; giving information about the new strategies in terms of the preparation method and their possible applications.

  15. High Efficiency Solar Thermochemical Reactor for Hydrogen Production.

    Energy Technology Data Exchange (ETDEWEB)

    McDaniel, Anthony H. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2017-09-30

    This research and development project is focused on the advancement of a technology that produces hydrogen at a cost that is competitive with fossil-based fuels for transportation. A twostep, solar-driven WS thermochemical cycle is theoretically capable of achieving an STH conversion ratio that exceeds the DOE target of 26% at a scale large enough to support an industrialized economy [1]. The challenge is to transition this technology from the laboratory to the marketplace and produce hydrogen at a cost that meets or exceeds DOE targets.

  16. Stage efficiency in the analysis of thermochemical water decomposition processes

    Science.gov (United States)

    Conger, W. L.; Funk, J. E.; Carty, R. H.; Soliman, M. A.; Cox, K. E.

    1976-01-01

    The procedure for analyzing thermochemical water-splitting processes using the figure of merit is expanded to include individual stage efficiencies and loss coefficients. The use of these quantities to establish the thermodynamic insufficiencies of each stage is shown. A number of processes are used to illustrate these concepts and procedures and to demonstrate the facility with which process steps contributing most to the cycle efficiency are found. The procedure allows attention to be directed to those steps of the process where the greatest increase in total cycle efficiency can be obtained.

  17. Experimental study of flow through compressor Cascade

    Directory of Open Access Journals (Sweden)

    Satyam Panchal

    2017-09-01

    Full Text Available The objective of this research work is to study the behaviour of flow at the inlet, within the blade passage and at the exit of a compressor cascade. For this purpose, a cascade with six numbers of aerofoil blades was designed and constructed. The cascade was fitted on the cascade test tunnel. Out of six blades two were instrumented for measuring the pressure distribution on the pressure and suction surface. The blades had a parabolic camber line, with a maximum camber position at 40% of the chord from the leading edge of the blade. The profile of the blade was C4, height of the blade was 160 mm, chord length was 80 mm, camber angle was 45° and stagger angle was 30°. Similarly, the length of the cascade was 300 mm, span was 160 mm, pitch was 60 mm, the actual chord of the cascade was 80 mm, the axial chord of the cascade was 70 mm, the stagger angle of the cascade was 30° and the pitch-chord ratio was 0.75. The data was taken and analyzed at −500% of the axial chord before the cascade, −25% of the axial chord before the leading edge, 25%, 50%, 75% and 150% of the axial chord from the leading edge of the blade. The readings were taken from the cascade wall to the mid span position along the pitch wise direction. The angle of incidence was also changed during the experiment and varied from i=−50°, −30°, −10° to 5°.

  18. Medical waste to energy: experimental study.

    Science.gov (United States)

    Arcuri, C; Luciani, F; Piva, P; Bartuli, F N; Ottria, L; Mecheri, B; Licoccia, S

    2013-04-01

    Although waste is traditionally assessed as a pollutant which needs to be reduced or lessened, its management is certainly necessary. Nowadays, biological fuel cells, through the direct conversion of organic matter to electricity using biocatalysts, represent a technology able to produce sustainable energy by means of waste treatment. This study aims to propose a mean to generate energy from blood and saliva, that are common risk-infectious medical waste. Material employed (purchased by Sigma-Aldrich) were: Glucose oxidase (GOx), Nafion perfluorinated resin solution at 5% in a mixture of lower aliphatic alcohols and water, Polyethylene oxide. Stock solutions of D (+) glucose were prepared in a 0.1 M phosphate buffer solution and stored at 4 °C for at least 24 h before use. Carbon cloth electrode ELAT HT 140 E-W with a platinum loading of 5 gm-2 was purchased by E-Tek. Electrospun Nafion fibers were obtained as follows. Scanning electron microscopy was used to characterize the electrode morphologies. In order to develop an effective immobilization strategy of GOx on the electrode surface, Nafion fibers (a fully fluorinated ion conducting polymer used as a membrane material in enzymatic fuel cells - EFC) were selected as immobilizing polymer matrix. In this work, exploiting the nafion fibers capability of being able to cathalize Gox activity, we have tried to produce an enzymatic fuel cell which could produce energy from the blood and the saliva within medical-dental waste. Medical waste refers to all those materials produced by the interaction among doctor and patient, such as blood and saliva. During our research we will try to complete an EFC prototype able to produce energy from blood and saliva inside the risk-infectious medical waste in order to contribute to the energy requirements of a consulting room.

  19. EXPERIMENTAL STUDY OF A HORSE ANTIPOLIOMYELITIC SERUM.

    Science.gov (United States)

    Rhoads, C P

    1931-01-01

    Through the kindness of Dr. W. H. Park we have been enabled to study a horse antipoliomyelitic serum. This preparation has been supplied us in three forms: citrated blood plasma, serum, and globulin concentrate. We have tested these preparations in vitro and in vivo for inactivating or neutralizing or, to use perhaps a better term, antiviral effects against a constant, potent, filtrate virus of poliomyelitis. The preparations exhibited these effects when combined in vitro. Their action in this respect appears to be greater and more constant than that found by Stewart and Haselbauer for the Pettit antipoliomyelitic horse serum. On the other hand, in vivo tests carried out by us were less successful. In comparison with the constancy of action, under given conditions, of convalescent monkey and human sera, the antipoliomyelitic horse serum displayed striking irregularity, and certain preparations were devoid of protective power. The precise nature of the inactivating substances in the horse antiserum and their relation to the corresponding substances in convalescent sera have still, to be determined. As far as one absorption test carried out by us indicates, precipitin does not play a major rôle in the inactivating process. When an active globulin concentrate was filtered through Berkefeld candles, it lost its in vitro inactivating power. This is not true of convalescent sera in the native state. No tests have, however, been made with globulin concentrates from such sera. The experiments described in this paper raise the question whether, therapeutically considered, the antipoliomyelitic horse serum should be regarded as an exact equivalent of, and hence employed as a perfect substitute for, convalescent serum. This question can only be answered by further experiment and observation.

  20. Markets and morals: an experimental survey study.

    Directory of Open Access Journals (Sweden)

    Julio J Elias

    Full Text Available Most societies prohibit some market transactions based on moral concerns, even when the exchanges would benefit the parties involved and would not create negative externalities. A prominent example is given by payments for human organs for transplantation, banned virtually everywhere despite long waiting lists and many deaths of patients who cannot find a donor. Recent research, however, has shown that individuals significantly increase their stated support for a regulated market for human organs when provided with information about the organ shortage and the potential beneficial effects a price mechanism. In this study we focused on payments for human organs and on another "repugnant" transaction, indoor prostitution, to address two questions: (A Does providing general information on the welfare properties of prices and markets modify attitudes toward repugnant trades? (B Does additional knowledge on the benefits of a price mechanism in a specific context affect attitudes toward price-based transactions in another context? By answering these questions, we can assess whether eliciting a market-oriented approach may lead to a relaxation of moral opposition to markets, and whether there is a cross-effect of information, in particular for morally controversial activities that, although different, share a reference to the "commercialization" of the human body. Relying on an online survey experiment with 5,324 U.S. residents, we found no effect of general information about market efficiency, consistent with morally controversial markets being accepted only when they are seen as a solution to a specific problem. We also found some cross-effects of information about a transaction on the acceptance of the other; however, the responses were mediated by the gender and (to a lesser extent religiosity of the respondent--in particular, women exposed to information about legalizing prostitution reduced their stated support for regulated organ payments. We

  1. Injury Based on Its Study in Experimental Models

    Directory of Open Access Journals (Sweden)

    M. Mendes-Braz

    2012-01-01

    Full Text Available The present review focuses on the numerous experimental models used to study the complexity of hepatic ischemia/reperfusion (I/R injury. Although experimental models of hepatic I/R injury represent a compromise between the clinical reality and experimental simplification, the clinical transfer of experimental results is problematic because of anatomical and physiological differences and the inevitable simplification of experimental work. In this review, the strengths and limitations of the various models of hepatic I/R are discussed. Several strategies to protect the liver from I/R injury have been developed in animal models and, some of these, might find their way into clinical practice. We also attempt to highlight the fact that the mechanisms responsible for hepatic I/R injury depend on the experimental model used, and therefore the therapeutic strategies also differ according to the model used. Thus, the choice of model must therefore be adapted to the clinical question being answered.

  2. Effects of thermo-chemical pre-treatment on anaerobic biodegradability and hydrolysis of lignocellulosic biomass

    NARCIS (Netherlands)

    Fernandes, T.; Klaasse Bos, G.J.; Zeeman, G.; Sanders, J.P.M.; Lier, van J.B.

    2009-01-01

    The effects of different thermo-chemical pre-treatment methods were determined on the biodegradability and hydrolysis rate of lignocellulosic biomass. Three plant species, hay, straw and bracken were thermo-chemically pre-treated with calcium hydroxide, ammonium carbonate and maleic acid. After

  3. Multi-scale visualization and characterization of lignocellulosic plant cell wall deconstruction during thermochemical pretreatment

    Science.gov (United States)

    Shishir P. S. Chundawat; Bryon S. Donohoe; Leonardo da Costa Sousa; Thomas Elder; Umesh P. Agarwal; Fachuang Lu; John Ralph; Michael E. Himmel; Venkatesh Balan; Bruce E. Dale

    2011-01-01

    Deconstruction of lignocellulosic plant cell walls to fermentable sugars by thermochemical and/or biological means is impeded by several poorly understood ultrastructural and chemical barriers. A promising thermochemical pretreatment called ammonia fiber expansion (AFEX) overcomes the native recalcitrance of cell walls through subtle morphological and physicochemical...

  4. An experimental study on pump clogging

    Science.gov (United States)

    Isono, M.; Nohmi, M.; Uchida, H.; Kawai, M.; Kudo, H.; Kawahara, T.; Miyagawa, K.; Saito, S.

    2014-03-01

    For sewage pump that various foreign substance is flowed into, anti-clogging performance is a factor as important as pump efficiency in order to avoid clogging trouble by foreign substance. Many investigations about pump inner flow and pump efficiency estimation have been carried out conventionally in order to realize coexistence with anti-clogging performance and pump performance. And these results have been reflected in construction of the running water section design method. As a index of anti-clogging performance, "impeller passage diameter" which is diameter of spherical solid that can pass through the pump is used widely. And there are various type of the sewage pump which have large impeller passage diameter. However real cause of clog is not a solid, and it is fibrous material such as towel and clothes, vinyl and paper diaper. In most case these material accumulate in the pump, so that clog is occurred. In this study, for the purpose of quantification of anti-clogging performance against fibrous materials, the factor that affect to clogging of pump was investigated by pump model test using a string. The test is done based on Taguchi method. In this test, type of the pump model, diameter of the string, material of the string, length of the string and flow rate are selected for the factor, and the effect that they have on the clogging of the pump was investigated. As a result of this test, it was made clear that length of the string has a strong influence on the clogging of the pump. And from the result of this test, evaluation method of anti-clogging performance of the pump against fibrous material by using string was considered. According to the result of above test based on Taguchi method, it was assumed that quantification of anti-clogging performance against fibrous materials is possible by flowing plural strings into the pump and calculating the probability of passing. Plurality sewage pumps of different types were evaluated based on this assumption

  5. Experimental Study of Rectangular Labyrinth Weir

    Directory of Open Access Journals (Sweden)

    M. Rezaee

    2016-09-01

    Full Text Available Introduction: Labyrinth weirs compare with straight weirs had required less freeboard in upstream so they are more appropriate for the irrigation networks. So they could maked more space to sotrage water and restrained foold with higher discharge. Labyrinths weirs have three generally form triangles, trapezoidal and rectangular that Tullis et al. (15 presented formula (3 for discharge coefficient of labyrinth weirs (triangles and rectangular and a few studiescarried out on rectangular shape and its hydraulic characteristics are not specified.Therefore main aim of this paper study and characterized hydraulic characteristics of rectangular labyrinth weirs by using laboratory data. Materials and Methods: In this study rectangular labyrinth weir discharge and coefficient discharge relationships used dimensional analysis and experiment on hydraulic modeling, constant coefficient was defined. Laboratory flume is shown in Figure 2 (0.5 m wide x 12 m long x 0.8 m deep. Models was made from clear plexiglass plate with 10 cm thickness thatcuted using leaserdevice and the crest manualy shaped quadrant with radius 10 cm, all models using silicon glue install in the flume. The upstream depth readership by point gauge that installed in upstream of models. Discharge calcutaed byupsterm depth of triangular weir that installed in down stream of flume.Data were analyzed by SPSS software and to compare relationships with each other used two parameter root mean square error and correlation coefficient and charts darw in Excel Results and Discussion: discharge coefficient formula (11 carried out by using SPSS software that compared with formula (3. Results showed (Tables 2 and 3 that the correlation coefficient of formula (11 was more than a formula (3 and formula (11 RSME was less than formula (3 RSME except in first and fifth hydraulic model (rectengular1 and 5 that they were almost equal. So the formula (11 was more accurate than a formula (3 to peredict

  6. Theoretical and Experimental Studies in Accelerator Physics

    Energy Technology Data Exchange (ETDEWEB)

    Rosenzweig, James [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy

    2017-03-08

    . We note also that PBPL graduates remain as close elaborators for the program after leaving UCLA. The UCLA PBPL program is a foremost developer of on-campus facilities, such as the Neptune and Pegasus Laboratories, providing a uniquely strong environment for student-based research. In addition, the PBPL is a strong user of off-campus national lab facilities, such as SLAC FACET and NLCTA, and the BNL ATF. UCLA has also vigorously participated in the development of these facilities. The dual emphases on off- and on-campus opportunities permit the PBPL to address in an agile way a wide selection of cutting-edge research topics. The topics embraced by this proposal illustrate this program aspect well. These include: GV/m dielectric wakefield acceleration/coherent Cerenkov radiation experiments at FACET (E-201) and the ATF; synergistic laser-excited dielectric accelerator and light source development; plasma wakefield (PWFA) experiments on “Trojan horse” ionization injection (FACET E-210), quasi-nonlinear PWFA at BNL and the production at Neptune high transformer ratio plasma wakes; the inauguration of a new type of RF photoinjector termed “hybrid” at UCLA, and application to PWFA; space-charge dominated beam and cathode/near cathode physics; the study of advanced IFEL systems, for very high energy gain and utilization of novel OAM modes; the physcis of inverse Compton scattering (ICS), with applications to e+ production and γγ colliders; electron diffraction; and advanced beam diagnostics using coherent imaging techniques. These subjects are addressed under the leadership of PBPL director Prof. James Rosenzweig in Task A, and Prof. Pietro Musumeci in Task J, which was initiated following his OHEP Outstanding Junior Investigator award.

  7. The experimental study of seed dispersal by fish (ichthyochory)

    NARCIS (Netherlands)

    Pollux, B.J.A.

    2011-01-01

    1.The last few years have seen an increased interest in the experimental study of seed dispersal by fish (ichthyochory). This paper reviews such experiments, aiming to determine what functional aspects of ichthyochory have been investigated, what experimental designs have been used and what the

  8. Bibliographic Review about Solar Hydrogen Production Through Thermochemical Cycles; Revision Bibliografica sobre la Produccion de Hidrogeno Solar Mediante Ciclos Termoquimicos

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez Saavedra, R.

    2008-08-06

    This report presents a summary of the different thermical processes used to obtain hydrogen through solar energy, paying more attention to the production of hydrogen from water through thermochemical cycles. In this aspect, it is briefly y described the most interesting thermochemical cycles, focusing on thermochemical cycles based on oxides. (Author) 25 refs.

  9. Bibliographic Review about Solar Hydrogen Production Through Thermochemical Cycles; Revision Bibliografica sobre la Produccion de Hidrogeno Solar Mediante Ciclos Termoquimicos

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez Saavedra, R.

    2007-12-28

    This report presents a summary of the different thermical processes used to obtain hydrogen through solar energy, paying more attention to the production of hydrogen from water through thermochemical cycles. In this aspect, it is briefly described the most interesting thermochemical cycles, focusing on thermochemical cycles based on oxides. (Author) 25 refs.

  10. Inner detached frequency response curves: an experimental study

    Science.gov (United States)

    Gatti, Gianluca; Brennan, Michael J.

    2017-05-01

    Certain nonlinear vibrating systems have frequency response curves (FRCs), in which isolated detached curves exist inside the main continuous FRC. The behavior of these systems has hitherto been studied analytically and numerically, but to the authors' knowledge, there is no record of an inner detached FRC being detected experimentally. These curves may be hidden by numerical or experimental analysis, particularly when a system is subject to swept or stepped-sine excitation. Their existence may thus lead to unexpected dramatic changes in the amplitude of the system response. This paper presents an experimental study that involves the design, construction and testing of a specific system that has an isolated detached FRC inside the main continuous FRC. The experimental design of the test rig is supported by multibody dynamic simulations, and in the experimental tests the existence of a detached FRC was verified.

  11. First thermochemical property of Seaborgium determined

    Energy Technology Data Exchange (ETDEWEB)

    Tuerler, A. for a LBNL Berkeley - Univ. Bern - FLNR Dubna -GSI Darmstadt - TU Dresden - Chalmers Univ. of Technology Goeteborg - GH Kassel - ITS and LLNL Livermore - Univ. Mainz - Univ. Oslo - FZ Rossendorf - JAERI Tokai - PSI Villigen collaboration

    1997-09-01

    The chemical properties of SgO{sub 2}Cl{sub 2} (element 106 = Seaborgium, Sg) were successfully studied using the On-line Gas Chromatography Apparatus (OLGA III). After chemical separation of Sg the nuclides {sup 265}Sg and {sup 266}Sg were unambiguously identified and their half-lives were determined for the first time. The Sg nuclides were produced from the {sup 248}Cm({sup 22}Ne,4,5n){sup 266,265}Sg reaction at the GSI Darmstadt UNILAC accelerator. Simultaneously, short-lived W nuclides were produced from a small admixture of {sup 152}Gd to the Cm target material. As predicted by relativistic calculations and by extrapolations of chemical properties, it was demonstrated that Sg oxychlorides are indeed less volatile than their lighter homologue Mo- and equally or less volatile than W-oxychlorides. (author) 1 fig., 1 tab., 4 refs.

  12. Numerical Modeling of Deep Mantle Flow: Thermochemical Convection and Entrainment

    Science.gov (United States)

    Mulyukova, Elvira; Steinberger, Bernhard; Dabrowski, Marcin; Sobolev, Stephan

    2013-04-01

    ) upwelling of the ambient material in the vicinity of the dense material (mechanism of selective withdrawal (Lister, 1989)), and (iii) cold downwellings sliding along the bottom boundary, and forcing the dense material upwards. The objective of this study is to compare the efficiency of entrainment by each of these mechanisms, and its dependence on the density and viscosity anomaly of the dense material with respect to the ambient mantle. To perform this study, we have developed a two-dimensional FEM code to model thermal convection in a hollow cylinder domain with presence of chemical heterogeneities, and using a realistic viscosity profile. We present the results of the simulations that demonstrate the entrainment mechanisms described above. In addition, we perfom numerical experiments in a Cartesian box domain, where the bottom right boundary of the box is deformed to resemble the geometry of an LLSVP edge. In some of the experiments, the bottom left part of the boundary is moving towards the right boundary, simulating a slab sliding along the core-mantle boundary towards an LLSVP. These experiments allow a detailed study of the process of entrainment, and its role in the thermochemical evolution of the Earth.

  13. Thermochemical conversion of microalgal biomass into biofuels: a review.

    Science.gov (United States)

    Chen, Wei-Hsin; Lin, Bo-Jhih; Huang, Ming-Yueh; Chang, Jo-Shu

    2015-05-01

    Following first-generation and second-generation biofuels produced from food and non-food crops, respectively, algal biomass has become an important feedstock for the production of third-generation biofuels. Microalgal biomass is characterized by rapid growth and high carbon fixing efficiency when they grow. On account of potential of mass production and greenhouse gas uptake, microalgae are promising feedstocks for biofuels development. Thermochemical conversion is an effective process for biofuel production from biomass. The technology mainly includes torrefaction, liquefaction, pyrolysis, and gasification. Through these conversion technologies, solid, liquid, and gaseous biofuels are produced from microalgae for heat and power generation. The liquid bio-oils can further be upgraded for chemicals, while the synthesis gas can be synthesized into liquid fuels. This paper aims to provide a state-of-the-art review of the thermochemical conversion technologies of microalgal biomass into fuels. Detailed conversion processes and their outcome are also addressed. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Evaluation of wastewater treatment requirements for thermochemical biomass liquefaction

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, D.C.

    1992-05-01

    The broad range of processing conditions involved in direct biomass liquefaction lead to a variety of product properties. The aqueous byproduct streams have received limited analyses because priority has been placed on analysis of the complex organic liquid product. The range of organic contaminants carried in the aqueous byproducts directly correlates with the quantity and quality of contaminants in the liquid oil product. The data in the literature gives a general indication of the types and amounts of components expected in biomass liquefaction wastewater; however, the data is insufficient to prepare a general model that predicts the wastewater composition from any given liquefaction process. Such a model would be useful in predicting the amount of water that would be soluble in a given oil and the level of dissolved water at which a second aqueous-rich phase would separate from the oil. Both biological and thermochemical processes have proposed for wastewater treatment, but no treatment process has been tested. Aerobic and anaerobic biological systems as well as oxidative and catalytic reforming thermochemical systems should be considered.

  15. Ability of thermochemical calculation to treat organic peroxides

    Science.gov (United States)

    Osmont, Antoine; Baudin, Gérard; Genetier, Marc

    2017-06-01

    Since 3 years, the CEA Gramat is developing a new thermochemical code, called SIAME, funded by DGA to help French defense industry at conceiving new explosives compositions. It enables the calculation of CJ detonation and deflagration points and combustion of explosives. The accuracy of the code has been checked on several compositions containing PETN, RDX, HMX, TNT, NTO. The error on the velocity of detonation is 3%. To enlarge the domain of validity of the code, organic peroxides have been considered. It is known that thermochemical simulation is in failure regarding compounds as simple as hydrogen peroxide. The computed velocity of detonation is 5720 m/s when shock planar impact gives 6150 m/s. The same discrepancy is found for TATP, with a calculated value at 5870 m/s when 5290 has been measured. Detonation velocity of TATP has been measured at two different densities. These velocities agree with other published values. A closer look at the enthalpy of formation of TATP has revealed that it comes from an article of 1932. Ab initio computations have given a totally different value, leading to better agreement with experiment.

  16. Techno-economic Analysis for the Thermochemical Conversion of Biomass to Liquid Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Yunhua; Tjokro Rahardjo, Sandra A.; Valkenburt, Corinne; Snowden-Swan, Lesley J.; Jones, Susanne B.; Machinal, Michelle A.

    2011-06-01

    ). This study is part of an ongoing effort within the Department of Energy to meet the renewable energy goals for liquid transportation fuels. The objective of this report is to present a techno-economic evaluation of the performance and cost of various biomass based thermochemical fuel production. This report also documents the economics that were originally developed for the report entitled “Biofuels in Oregon and Washington: A Business Case Analysis of Opportunities and Challenges” (Stiles et al. 2008). Although the resource assessments were specific to the Pacific Northwest, the production economics presented in this report are not regionally limited. This study uses a consistent technical and economic analysis approach and assumptions to gasification and liquefaction based fuel production technologies. The end fuels studied are methanol, ethanol, DME, SNG, gasoline and diesel.

  17. Studies on pathogenesis and treatment of experimental immune complex glomerulonephrtis.

    NARCIS (Netherlands)

    Fleuren, Gerard Johannes Maria

    1976-01-01

    Chapter 1. In this thesis an investigation into pathogenetic mechanisms of epimembranous immune complex depostion in the glomeruli was described. For this study we used two related models of experimental immune complex glemerulonephritis: the heterologous and the autologous immune complex

  18. Experimental study of convective flows in the freezer

    Directory of Open Access Journals (Sweden)

    Krasnoshlykov Alexander

    2014-01-01

    Full Text Available The article discusses an experimental study of convective heat transfer in the amount of air and water in the freezer, under various operating conditions of the refrigeration unit.

  19. Experimental geothermal research facilities study (Phase 0). Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    1974-01-01

    The study comprises Phase 0 of a project for Experimental Geothermal Research Facilities. The study focuses on identification of a representative liquid-dominated geothermal reservoir of moderate temperature and salinity, preliminary engineering design of an appropriate energy conversion system, identification of critical technology, and planning for implementation of experimental facilities. The objectives included development of liaison with the industrial sector, to ensure responsiveness to their views in facility requirements and planning, and incorporation of environmental and socioeconomic factors. This Phase 0 report covers problem definition and systems requirements. Facilities will incorporate capability for research in component, system, and materials technology and a nominal 10 MWe experimental, binary cycle, power generating plant.

  20. Coupled thermochemical, isotopic evolution and heat transfer simulations in highly irradiated UO{sub 2} nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Piro, M.H.A., E-mail: markuspiro@gmail.com [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Banfield, J. [Nuclear Engineering Department, University of Tennessee, Knoxville, TN (United States); Clarno, K.T., E-mail: clarnokt@ornl.gov [Reactor and Nuclear Systems Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Simunovic, S. [Computer Science and Mathematics Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Besmann, T.M. [Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Lewis, B.J.; Thompson, W.T. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, ON (Canada)

    2013-10-15

    Predictive capabilities for simulating irradiated nuclear fuel behavior are enhanced in the current work by coupling thermochemistry, isotopic evolution and heat transfer. Thermodynamic models that are incorporated into this framework not only predict the departure from stoichiometry of UO{sub 2}, but also consider dissolved fission and activation products in the fluorite oxide phase, noble metal inclusions, secondary oxides including uranates, zirconates, molybdates and the gas phase. Thermochemical computations utilize the spatial and temporal evolution of the fission and activation product inventory in the pellet, which is typically neglected in nuclear fuel performance simulations. Isotopic computations encompass the depletion, decay and transmutation of more than 2000 isotopes that are calculated at every point in space and time. These computations take into consideration neutron flux depression and the increased production of fissile plutonium near the fuel pellet periphery (i.e., the so-called “rim effect”). Thermochemical and isotopic predictions are in very good agreement with reported experimental measurements of highly irradiated UO{sub 2} fuel with an average burnup of 102 GW d t(U){sup −1}. Simulation results demonstrate that predictions are considerably enhanced when coupling thermochemical and isotopic computations in comparison to empirical correlations. Notice: This manuscript has been authored by UT-Battelle, LLC, under Contract No. DE-AC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes.

  1. Thermo-chemical evolution of magmatic systems at mid-crustal level: the role of chaotic advection

    Science.gov (United States)

    Petrelli, Maurizio; El Omari, Kamal; Le Guer, Yves; Perugini, Diego

    2016-04-01

    Unravelling the dynamics occurring during the thermo-chemical evolution of igneous bodies is of crucial importance in both petrology and volcanology. This is particularly true in subduction related systems where large amounts of magma start, and sometimes end, their differentiation histories at mid and lower crust levels. These magmas play a fundamental role in the evolution of both plutonic and volcanic systems but several key questions are still open about their thermal and chemical evolution: 1) what are the dynamics governing the development of these magmatic systems, 2) what are the timescales of cooling, crystallization and chemical differentiation; 4) how these systems contribute to the evolution of shallower magmatic systems? Recent woks shed light on the mechanisms acting during the growing of new magmatic bodies and it is now accepted that large crustal igneous bodies result from the accretion and/or amalgamation of smaller ones. What is lacking now is how fluid dynamics of magma bodies can influence the evolution of these igneous systems. In this contribution we focus on the thermo-chemical evolution of a subduction related magmatic system at pressure conditions corresponding to mid-crustal levels (0.7 GPa, 20-25 km). In order to develop a robust model and address the Non-Newtonian behavior of crystal bearing magmas, we link the numerical formulation of the problem to experimental results and rheological modeling. We define quantitatively the thermo-chemical evolution of the system and address the timing required to reach the maximum packing fraction. We will show that the development of chaotic dynamics significantly speed up the crystallization process decreasing the time needed to reach the maximum packing fraction. Our results have important implications for both the rheological history of the magmatic body and the refilling of shallower magmatic systems.

  2. Experimental Study on the Langlee Wave Energy Converter

    DEFF Research Database (Denmark)

    Lavelle, John; Kofoed, Jens Peter

    This report concerns the experimental study of the 1:20 scale model of the Langlee Wave Energy Converter (WEC) carried out at Aalborg University’s wave basin during the summer of 2010.......This report concerns the experimental study of the 1:20 scale model of the Langlee Wave Energy Converter (WEC) carried out at Aalborg University’s wave basin during the summer of 2010....

  3. The role of labile sulfur compounds in thermochemical sulfate reduction

    Science.gov (United States)

    Amrani, Alon; Zhang, Tongwei; Ma, Qisheng; Ellis, Geoffrey S.; Tang, Yongchun

    2008-06-01

    The reduction of sulfate to sulfide coupled with the oxidation of hydrocarbons to carbon dioxide, commonly referred to as thermochemical sulfate reduction (TSR), is an important abiotic alteration process that most commonly occurs in hot carbonate petroleum reservoirs. In the present study we focus on the role that organic labile sulfur compounds play in increasing the rate of TSR. A series of gold-tube hydrous pyrolysis experiments were conducted with n-octane and CaSO4 in the presence of reduced sulfur (e.g. H2S, S°, organic S) at temperatures of 330 and 356 °C under a constant confining pressure. The in-situ pH was buffered to 3.5 (∼6.3 at room temperature) with talc and silica. For comparison, three types of oil with different total S and labile S contents were reacted under similar conditions. The results show that the initial presence of organic or inorganic sulfur compounds increases the rate of TSR. However, organic sulfur compounds, such as 1-pentanethiol or diethyldisulfide, were significantly more effective in increasing the rate of TSR than H2S or elemental sulfur (on a mole S basis). The increase in rate is achieved at relatively low concentrations of 1-pentanethiol, less than 1 wt% of the total n-octane, which is comparable to the concentration of organic S that is common in many oils (∼0.3 wt%). We examined several potential reaction mechanisms to explain the observed reactivity of organic LSC. First, the release of H2S from the thermal degradation of thiols was discounted as an important mechanism due to the significantly greater reactivity of thiol compared to an equivalent amount of H2S. Second, we considered the generation of olefines in association with the elimination of H2S during thermal degradation of thiols because olefines are much more reactive than n-alkanes during TSR. In our experiments, olefines increased the rate of TSR, but were less effective than 1-pentanethiol and other organic LSC. Third, the thermal decomposition of

  4. The role of labile sulfur compounds in thermochemical sulfate reduction

    Science.gov (United States)

    Amrani, A.; Zhang, T.; Ma, Q.; Ellis, G.S.; Tang, Y.

    2008-01-01

    The reduction of sulfate to sulfide coupled with the oxidation of hydrocarbons to carbon dioxide, commonly referred to as thermochemical sulfate reduction (TSR), is an important abiotic alteration process that most commonly occurs in hot carbonate petroleum reservoirs. In the present study we focus on the role that organic labile sulfur compounds play in increasing the rate of TSR. A series of gold-tube hydrous pyrolysis experiments were conducted with n-octane and CaSO4 in the presence of reduced sulfur (e.g. H2S, S??, organic S) at temperatures of 330 and 356 ??C under a constant confining pressure. The in-situ pH was buffered to 3.5 (???6.3 at room temperature) with talc and silica. For comparison, three types of oil with different total S and labile S contents were reacted under similar conditions. The results show that the initial presence of organic or inorganic sulfur compounds increases the rate of TSR. However, organic sulfur compounds, such as 1-pentanethiol or diethyldisulfide, were significantly more effective in increasing the rate of TSR than H2S or elemental sulfur (on a mole S basis). The increase in rate is achieved at relatively low concentrations of 1-pentanethiol, less than 1 wt% of the total n-octane, which is comparable to the concentration of organic S that is common in many oils (???0.3 wt%). We examined several potential reaction mechanisms to explain the observed reactivity of organic LSC. First, the release of H2S from the thermal degradation of thiols was discounted as an important mechanism due to the significantly greater reactivity of thiol compared to an equivalent amount of H2S. Second, we considered the generation of olefines in association with the elimination of H2S during thermal degradation of thiols because olefines are much more reactive than n-alkanes during TSR. In our experiments, olefines increased the rate of TSR, but were less effective than 1-pentanethiol and other organic LSC. Third, the thermal decomposition of

  5. Entropy Analysis of Solar Two-Step Thermochemical Cycles for Water and Carbon Dioxide Splitting

    Directory of Open Access Journals (Sweden)

    Matthias Lange

    2016-01-01

    Full Text Available The present study provides a thermodynamic analysis of solar thermochemical cycles for splitting of H2O or CO2. Such cycles, powered by concentrated solar energy, have the potential to produce fuels in a sustainable way. We extend a previous study on the thermodynamics of water splitting by also taking into account CO2 splitting and the influence of the solar absorption efficiency. Based on this purely thermodynamic approach, efficiency trends are discussed. The comprehensive and vivid representation in T-S diagrams provides researchers in this field with the required theoretical background to improve process development. Furthermore, results about the required entropy change in the used redox materials can be used as a guideline for material developers. The results show that CO2 splitting is advantageous at higher temperature levels, while water splitting is more feasible at lower temperature levels, as it benefits from a great entropy change during the splitting step.

  6. Global thermochemical imaging of the lithosphere using satellite and terrestrial observations

    Science.gov (United States)

    Fullea, Javier; Lebedev, Sergei; Martinec, Zdenek; Celli, Nicolas

    2017-04-01

    Conventional methods of seismic tomography, topography, gravity and electromagnetic data analysis and geodynamic modelling constrain distributions of seismic velocity, density, electrical conductivity, and viscosity at depth, all depending on temperature and composition of the rocks within the Earth. However, modelling and interpretation of multiple data sets provide a multifaceted image of the true thermochemical structure of the Earth that needs to be appropriately and consistently integrated. A simple combination of gravity, electromagnetic, geodynamics, petrological and seismic models alone is insufficient due to the non-uniqueness and different sensitivities of these models, and the internal consistency relationships that must connect all the intermediate parameters describing the Earth involved. Thermodynamic and petrological links between seismic velocities, density, electrical conductivity, viscosity, melt, water, temperature, pressure and composition within the Earth can now be modelled accurately using new methods of computational petrology and data from laboratory experiments. The growth of very large terrestrial and satellite (e.g., Swarm and GOCE ESA missions) geophysical data sets over the last few years, together with the advancement of petrological and geophysical modelling techniques, now present an opportunity for global, thermochemical and deformation 3D imaging of the lithosphere and underlying upper mantle with unprecedented resolution. This project combines state-of-the-art seismic waveform tomography (using both surface and body waves), newly available global gravity satellite data (geoid and gravity anomalies and new gradiometric measurements from ESA's GOCE mission) and surface heat flow and elevation within a self-consistent thermodynamic framework. The aim is to develop a method for detailed and robust global thermochemical image of the lithosphere and underlying upper mantle. In a preliminary study, we convert a state-of-the-art global

  7. A theoretical and experimental study of coplanar waveguide shunt stubs

    Science.gov (United States)

    Dib, Nihad I.; Ponchak, George E.; Katehi, Linda P. B.

    1993-01-01

    A comprehensive theoretical and experimental study of straight and bent coplanar waveguide (CPW) shunt stubs is presented. In the theoretical analysis, the CPW is assumed to be inside a cavity while, the experiments are performed on open structures. For the analysis of CPW discontinuities with air-bridges, a hybrid technique was developed which was validated through extensive theoretical and experimental comparisons. The effect of the cavity resonances on the behavior of the stubs with and without air-bridges is investigated. In addition, the encountered radiation loss due to the discontinuities is evaluated experimentally.

  8. Experimental study of the robust global synchronization of Brockett oscillators

    Science.gov (United States)

    Ahmed, Hafiz; Ushirobira, Rosane; Efimov, Denis

    2017-12-01

    This article studies the experimental synchronization of a family of a recently proposed oscillator model, i.e. the Brockett oscillator [R. Brockett, Synchronization without periodicity, in Mathematical Systems Theory, A Volume in Honor of U. Helmke, edited by K. Huper, J. Trumpf (CreateSpace, Seattle, USA, 2013), pp. 65-74]. Due to its structural property, Brockett oscillator can be considered as a promising benchmark nonlinear model for investigating synchronization and the consensus phenomena. Our experimental setup consists of analog circuit realizations of a network of Brockett oscillators. Experimental results obtained in this work correspond to the prior theoretical findings.

  9. Using an experimental model for the study of therapeutic touch.

    Science.gov (United States)

    dos Santos, Daniella Soares; Marta, Ilda Estéfani Ribeiro; Cárnio, Evelin Capellari; de Quadros, Andreza Urba; Cunha, Thiago Mattar; de Carvalho, Emilia Campos

    2013-02-01

    to verify whether the Paw Edema Model can be used in investigations about the effects of Therapeutic Touch on inflammation by measuring the variables pain, edema and neutrophil migration. this is a pilot and experimental study, involving ten male mice of the same genetic strain and divided into experimental and control group, submitted to the chemical induction of local inflammation in the right back paw. The experimental group received a daily administration of Therapeutic Touch for 15 minutes during three days. the data showed statistically significant differences in the nociceptive threshold and in the paw circumference of the animals from the experimental group on the second day of the experiment. the experiment model involving animals can contribute to study the effects of Therapeutic Touch on inflammation, and adjustments are suggested in the treatment duration, number of sessions and experiment duration.

  10. Oxidation of metal sulfites by iodine for use in thermochemical hydrogen cycles

    Science.gov (United States)

    Mason, C. F. V.; Bowman, M. G.

    1981-09-01

    It is noted that thermochemical hydrogen cycles involving metal sulfates offer an alternative to sulfuric acid which is corrosive and has high energy requirements for drying prior to its thermal decomposition. The formation of such metal sulfates in conjunction with a low temperature hydrogen formation step is discussed. The following reaction was studied: MgSO3(c) + MgO(c) + I2(g) yields MgSO4(c) + MgI2(c). Although magnesium sulfite appears promising for this oxidation, a search was conducted for alternative metal sulfites which fit the following criteria for use: (1) sulfate must decompose in the temperature range available ( 1400 K); (2) iodide must hydrolyze easily; and (3) salts must not be rare, toxic, or expensive. Lanthanum and titanium fit these criteria.

  11. A general model for techno-economic analysis of CSP plants with thermochemical energy storage systems

    Science.gov (United States)

    Peng, Xinyue; Maravelias, Christos T.; Root, Thatcher W.

    2017-06-01

    Thermochemical energy storage (TCES), with high energy density and wide operating temperature range, presents a potential solution for CSP plant energy storage. We develop a general optimization based process model for CSP plants employing a wide range of TCES systems which allows us to assess the plant economic feasibility and energy efficiency. The proposed model is applied to a 100 MW CSP plant employing ammonia or methane TCES systems. The methane TCES system with underground gas storage appears to be the most promising option, achieving a 14% LCOE reduction over the current two-tank molten-salt CSP plants. For general TCES systems, gas storage is identified as the main cost driver, while the main energy driver is the compressor electricity consumption. The impacts of separation and different reaction parameters are also analyzed. This study demonstrates that the realization of TCES systems for CSP plants is contingent upon low storage cost and a reversible reaction with proper reaction properties.

  12. Non-equilibrium thermochemical heat storage in porous media

    DEFF Research Database (Denmark)

    Nagel, T.; Shao, H.; Singh, Ashok

    2013-01-01

    compressible gas flow through a porous solid is presented along with its finite element implementation where solid-gas reactions occur and both phases have individual temperature fields. The model is embedded in the Theory of Porous Media and the derivation is based on the evaluation of the Clausius...... determine reaction kinetics. To advance this technology beyond the laboratory stage requires a thorough theoretical understanding of the multiphysics phenomena and their quantification on a scale relevant to engineering analyses. Here, the theoretical derivation of a macroscopic model for multicomponent......Thermochemical energy storage can play an important role in the establishment of a reliable renewable energy supply and can increase the efficiency of industrial processes. The application of directly permeated reactive beds leads to strongly coupled mass and heat transport processes that also...

  13. Thermochemical treatment of biogas digestate solids to produce organic fertilisers

    DEFF Research Database (Denmark)

    Pantelopoulos, Athanasios

    digestate nitrogen content (Paper I), ii) determine their C and N dynamics after soil incorporation (Paper II) and iii) assess the plant N and P uptake of ryegrass amended with different thermochemical treatments of the solids (Paper III). For a more mechanistic understanding of the processes involved......Anaerobic digestion of animal manures has been proposed as a process with twofold advantage. The production of biogas, a renewable source of energy, and the treatment of animal manures to increase their agronomic value and reduce their environmental impact. However, the residual of anaerobic...... digestion, called digestate, may need a combination of treatments to improve its manageability, reduce its environmental impact and facilitate the exportation of excessive nutrients to other areas. Often, mechanical separation, is implemented as a first treatment of the digestate. The resulting solids from...

  14. Thermochemical structure of the Earth's mantle and continental crust

    DEFF Research Database (Denmark)

    Guerri, Mattia

    elastic properties and chemical composition taking into account the thermal and pressure effects. I found that even small amounts of H2O have an extremely high impact on the elastic properties of crustal rock. In addition, I show the potential that modifications in the stable mineralogical assemblage have...... be therefore used as a constraint regarding the mantle thermo-chemical structure. In the thesis I highlight the fact that the modelling of the isostatic component of topography is affected by uncertainties large enough to hamper a clear detection of the dynamic effects. Furthermore, residual topography maps...... (obtained as the difference between observed topography and computed isostatic component) and dynamic topography maps (computed through mantle flow modelling), that theoretically should both represent the effect of mantle convection on surface topography, present instead a low correlation coefficient. I...

  15. THERMOCHEMICAL CALCULATIONS USING SERVICEORIENTED ARCHITECTURE IN THE WEB SERVICE FORM

    Directory of Open Access Journals (Sweden)

    Pavel Horovčák

    2018-02-01

    Full Text Available The subject of this article is the service-oriented architecture utilization in the design and implementation of a web service that is intended to perform selected thermochemical calculations for chemical reactions. Computing functions allow the chemical reaction calculations, such as molar heat capacity, enthalpy, entropy and Gibbs free energy. In the next part, there is a description of each function, the method of service calling in the client application and the structure specification of outputs and error states of the service. In addition to computing functions, the web service also has a group of three information functions that characterize the purpose of the web service and its parameters, provide in tabular form a list of all web service functions and a list of all error states of the web service. The final section describes the presentation web service application with a demonstration of the specific calculations, the possibilities of using the service, and a further solution treatment.

  16. Environmental impact comparison of steam methane reformation and thermochemical processes of hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Naterer, G.F.; Jaber, O.; Dincer, I. [Ontario Univ., Oshawa, ON (Canada). Inst. of Technology

    2010-07-01

    This paper compares the environmental impact of various processes of hydrogen production, particularly steam methane reforming (SMR) and the copper-chlorine (Cu-Cl) and modified sulfur-iodine (S-I) thermochemical cycles. Natural gas is used as the energy source for each of the different methods. Also, an integrated Cu-Cl and SMR plant is examined to show the reduction of greenhouse gas emissions by modifying existing SMR plants with thermochemical processes. The analysis shows that the thermochemical Cu-Cl cycle outperforms the other conventional methods of hydrogen production, with lower fuel requirements and carbon dioxide emissions. (orig.)

  17. Estimation of thermochemical behavior of spallation products in mercury target

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Kaoru; Kaminaga, Masanori; Haga, Katsuhiro; Kinoshita, Hidetaka; Aso, Tomokazu; Teshigawara, Makoto; Hino, Ryutaro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2002-02-01

    In order to examine the radiation safety of a spallation mercury target system, especially source term evaluation, it is necessary to clarify the chemical forms of spallation products generated by spallation reaction with proton beam. As for the chemical forms of spallation products in mercury that involves large amounts of spallation products, these forms were estimated by using the binary phase diagrams and the thermochemical equilibrium calculation based on the amounts of spallation product. Calculation results showed that the mercury would dissolve Al, As, B, Be, Bi, C, Co, Cr, Fe, Ga, Ge, Ir, Mo, Nb, Os, Re, Ru, Sb, Si, Ta, Tc, V and W in the element state, and Ag, Au, Ba, Br, Ca, Cd, Ce, Cl, Cs, Cu, Dy, Er, Eu, F, Gd, Hf, Ho, I, In, K, La, Li, Lu, Mg, Mn, Na, Nd, Ni, O, Pb, Pd, Pr, Pt, Rb, Rh, S, Sc, Se, Sm, Sn, Sr, Tb, Te, Ti, Tl, Tm, Y, Yb, Zn and Zr in the form of inorganic mercury compounds. As for As, Be, Co, Cr, Fe, Ge, Ir, Mo, Nb, Os, Pt, Re, Ru, Se, Ta, V, W and Zr, precipitation could be occurred when increasing the amounts of spallation products with operation time of the spallation target system. On the other hand, beryllium-7 (Be-7), which is produced by spallation reaction of oxygen in the cooling water of a safety hull, becomes the main factor of the external exposure to maintain the cooling loop. Based on the thermochemical equilibrium calculation to Be-H{sub 2}O binary system, the chemical forms of Be in the cooling water were estimated. Then the Be could exist in the form of cations such as BeOH{sup +}, BeO{sup +} and Be{sup 2+} under the condition of less than 10{sup -8} of the Be mole fraction in the cooling water. (author)

  18. Enhancing anaerobic digestibility and phosphorus recovery of dairy manure through microwave-based thermochemical pretreatment.

    Science.gov (United States)

    Jin, Ying; Hu, Zhenhu; Wen, Zhiyou

    2009-08-01

    Anaerobic digestion and struvite precipitation are two effective ways of treating dairy manure for recovering biogas and phosphorus. Anaerobic digestion of dairy manure is commonly limited by slow fiber degradation, while struvite precipitation is limited by the availability of orthophosphate. The aim of this work is to study the possibility of using microwave-based thermochemical pretreatment to simultaneously enhance manure anaerobic digestibility (through fiber degradation) and struvite precipitation (through phosphorus solubilization). Microwave heating combined with different chemicals (NaOH, CaO, H(2)SO(4), or HCl) enhanced solubilization of manure and degradation of glucan/xylan in dairy manure. However, sulfuric acid-based pretreatment resulted in a low anaerobic digestibility, probably due to the sulfur inhibition and Maillard side reaction. The pretreatments released 20-40% soluble phosphorus and 9-14% ammonium. However, CaO-based pretreatment resulted in lower orthophosphate releases and struvite precipitation efficiency as calcium interferes with phosphate to form calcium phosphate. Collectively, microwave heating combined with NaOH or HCl led to a high anaerobic digestibility and phosphorus recovery. Using these two chemicals, the performance of microwave- and conventional-heating in thermochemical pretreatment was further compared. The microwave heating resulted in a better performance in terms of COD solubilization, glucan/xylan reduction, phosphorus solubilization and anaerobic digestibility. Lastly, temperature and heating time used in microwave treatment were optimized. The optimal values of temperature and heating time were 147 degrees C and 25.3 min for methane production, and 135 degrees C and 26 min for orthophosphate release, respectively.

  19. Nutrient digestion and performance by lambs and steers fed thermochemically treated crop residues.

    Science.gov (United States)

    Sewell, J R; Berger, L L; Nash, T G; Cecava, M J; Doane, P H; Dunn, J L; Dyer, M K; Pyatt, N A

    2009-03-01

    Five studies were conducted to determine nutrient digestibility and performance of lambs and steers fed thermochemically treated crop residues and distillers dried grains with solubles (DDGS) as a corn replacement pellet (CRP; 75% residue:25% DDGS, DM basis). Fifteen Hampshire, Suffolk, or Dorset wethers (BW 33.3 +/- 5.0 kg) were utilized to evaluate nutrient digestibility of the unprocessed native (NAT) and CRP [Exp. 1: wheat straw (WS); Exp. 2: corn stover (CS); Exp. 3: switchgrass (SWG) and corn fiber:wheat chaff (CFWC)] when limit fed (Exp. 1 and 2: 1.8% of BW daily; Exp. 3: 2.5% of BW daily) compared with a 60% corn diet. In Exp. 4, 56 individually fed Dorset-cross wether lambs (BW 32.0 +/- 1.4 kg) were utilized to compare performance and digestibility of WS, wheat chaff (WC), corn fiber (CF), a 3:1 blend of corn fiber:wheat straw (CFWS), a 3:1 blend of CFWC, and SWG-CRP fed for ad libitum intake compared with a 45% corn diet. In Exp. 5, 32 individually fed Holstein steers (BW 185.2 +/- 0.9 kg) were used to evaluate performance and digestibility of diets containing corn, WS-CRP, CFWC-CRP, or NAT-WS fed for ad libitum intake. Crop residues were processed with 5% calcium oxide (DM basis) and 35% water in a double-shaft enclosed mixer (Readco Kurimoto Continuous Processor, York, PA) and subsequently pelleted with DDGS to form CRP. Feeding lambs WS-CRP (Exp. 1) or CS-CRP (Exp. 2) increased digestion of DM, NDF, and ADF compared with NAT (P crop residues are thermochemically processed. Processed crop residues may be fed in combination with DDGS to partially replace corn in ruminant diets.

  20. Bioenergy co-products derived from microalgae biomass via thermochemical conversion--life cycle energy balances and CO2 emissions.

    Science.gov (United States)

    Khoo, H H; Koh, C Y; Shaik, M S; Sharratt, P N

    2013-09-01

    An investigation of the potential to efficiently convert lipid-depleted residual microalgae biomass using thermochemical (gasification at 850 °C, pyrolysis at 550 °C, and torrefaction at 300 °C) processes to produce bioenergy derivatives was made. Energy indicators are established to account for the amount of energy inputs that have to be supplied to the system in order to gain 1 MJ of bio-energy output. The paper seeks to address the difference between net energy input-output balances based on a life cycle approach, from "cradle-to-bioenergy co-products", vs. thermochemical processes alone. The experimental results showed the lowest results of Net Energy Balances (NEB) to be 0.57 MJ/MJ bio-oil via pyrolysis, and highest, 6.48 MJ/MJ for gas derived via torrefaction. With the complete life cycle process chain factored in, the energy balances of NEBLCA increased to 1.67 MJ/MJ (bio-oil) and 7.01 MJ/MJ (gas). Energy efficiencies and the life cycle CO2 emissions were also calculated. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Experimental study of mechanical properties of friction welded AISI ...

    Indian Academy of Sciences (India)

    Friction welding is widely used as a mass production method in various industries. In the present study, an experimental set-up was designed in order to achieve friction welding of plastically deformed AISI 1021 steels. In this study, low alloy steel (AISI 1021) was welded under different welding parameters and afterwards ...

  2. Experimental study of mechanical properties of friction welded AISI ...

    Indian Academy of Sciences (India)

    Abstract. Friction welding is widely used as a mass production method in vari- ous industries. In the present study, an experimental set-up was designed in order to achieve friction welding of plastically deformed AISI 1021 steels. In this study, low alloy steel (AISI 1021) was welded under different welding parameters and ...

  3. Infections in orthopaedic surgery : clinical and experimental studies

    NARCIS (Netherlands)

    Vogely, Henri Charles

    2000-01-01

    The diagnostic difficulties, variability in outcome and the heterogeinity of the problem of orthopaedic infections stimulated the author to a study of the literature, and several clinical and experimental studies. The diagnosis prosthesis-related infection can only be reached with an acceptable

  4. Systematic review of experimental studies on intestinal anastomosis

    NARCIS (Netherlands)

    Yauw, S.T.K.; Wever, K.E.; Hoesseini, A.; Ritskes-Hoitinga, M.; Goor, H. van

    2015-01-01

    BACKGROUND: The contribution of animal research to a reduction in clinical intestinal anastomotic leakage is unknown, despite numerous experimental studies. In view of the current societal call to replace, reduce and refine animal experiments, this study examined the quality of animal research

  5. What Shapes the Intention to Study Abroad? An Experimental Approach

    Science.gov (United States)

    Petzold, Knut; Moog, Petra

    2018-01-01

    In contrast to previous studies, this investigation aims to get deeper insights into the causes of the intention to study abroad by using an experimental approach. Although international experience is often considered as important, many students at German universities do not even consider abroad. Referring to the Theory of Rational Choice (RCT)…

  6. Experimental Study of the Production of Solar Hydrogen in Algeria ...

    African Journals Online (AJOL)

    Hydrogen is a sustainable fuel option and one of the potential solutions for the current energy and environmental problems. In this study hydrogen is produced using a hydrogen generator with a Proton Exchange Membrane (PEM) electrolyser. An experimental study is done in the Center of Development of the Renewable ...

  7. Experimental Studies on Electronic Portfolios in Turkey: A Literature Review

    Science.gov (United States)

    Alan, Selahattin; Sünbül, Ali Murat

    2015-01-01

    In this study, a literature review was conducted about an individual's selected efforts, products stored in electronic format, and electronic portfolios that reflect the development and capacity of multimedia systems. In this context, relevant experimental studies performed in Turkey are collected to show e-portfolio application forms, their…

  8. Diffusion in liquids a theoretical and experimental study

    CERN Document Server

    Tyrrell, H J V

    1984-01-01

    Diffusion in Liquids: A Theoretical and Experimental Study aims to discuss the principles, applications, and advances in the field of diffusion, thermal diffusion, and thermal conduction in liquid systems. The book covers topics such as the principles of non-equilibrium thermodynamics; diffusion in binary and multicompetent systems; and experimental methods of studying diffusion processes in liquids. Also covered in the book are topics such as the theoretical interpretations of diffusion coefficients; hydrodynamic and kinetic theories; and diffusion in electrolyte systems. The text is recommen

  9. Analytical and Experimental Study of Residual Stresses in CFRP

    Directory of Open Access Journals (Sweden)

    Chia-Chin Chiang

    2013-01-01

    Full Text Available Fiber Bragg Grating sensors (FBGs have been utilized in various engineering and photoelectric fields because of their good environment tolerance. In this research, residual stresses of carbon fiber reinforced polymer composites (CFRP were studied using both experimental and analytical approach. The FBGs were embedded inside middle layers of CFRP to study the formation of residual stress during curing process. Finite element analysis was performed using ABAQUS software to simulate the CFRP curing process. Both experimental and simulation results showed that the residual stress appeared during cooling process and the residual stresses could be released when the CFRP was machined to a different shape.

  10. Third millenium ideal gas and condensed phase thermochemical database for combustion (with update from active thermochemical tables).

    Energy Technology Data Exchange (ETDEWEB)

    Burcat, A.; Ruscic, B.; Chemistry; Technion - Israel Inst. of Tech.

    2005-07-29

    The thermochemical database of species involved in combustion processes is and has been available for free use for over 25 years. It was first published in print in 1984, approximately 8 years after it was first assembled, and contained 215 species at the time. This is the 7th printed edition and most likely will be the last one in print in the present format, which involves substantial manual labor. The database currently contains more than 1300 species, specifically organic molecules and radicals, but also inorganic species connected to combustion and air pollution. Since 1991 this database is freely available on the internet, at the Technion-IIT ftp server, and it is continuously expanded and corrected. The database is mirrored daily at an official mirror site, and at random at about a dozen unofficial mirror and 'finger' sites. The present edition contains numerous corrections and many recalculations of data of provisory type by the G3//B3LYP method, a high-accuracy composite ab initio calculation. About 300 species are newly calculated and are not yet published elsewhere. In anticipation of the full coupling, which is under development, the database started incorporating the available (as yet unpublished) values from Active Thermochemical Tables. The electronic version now also contains an XML file of the main database to allow transfer to other formats and ease finding specific information of interest. The database is used by scientists, educators, engineers and students at all levels, dealing primarily with combustion and air pollution, jet engines, rocket propulsion, fireworks, but also by researchers involved in upper atmosphere kinetics, astrophysics, abrasion metallurgy, etc. This introductory article contains explanations of the database and the means to use it, its sources, ways of calculation, and assessments of the accuracy of data.

  11. Experimental study of lithium target under high power load

    Energy Technology Data Exchange (ETDEWEB)

    Khripunov, B.I. E-mail: boris@nfi.kiae.ru; Petrov, V.B.; Shapkin, V.V.; Pleshakov, A.S.; Rupyshev, A.S.; Antonov, N.V.; Litnovsky, A.M.; Romanov, P.V.; Shpansky, Yu.S.; Evtikhin, V.A.; Lyublinsky, I.E.; Vertkov, A.V

    2001-03-01

    This paper presents experimental research on simulation of a free liquid lithium surface under high heat flux impact for divertor application. Capillary porous structure (CPS) was taken to form the free liquid metal surface imitating divertor target plate. Experiments were performed in the SPRUT-4 linear plasma device with electron beam as power source. Lithium-filled targets were investigated at 1-50 MW/m{sup 2} heat loads in steady state. Lithium evaporation, energy and mass balance, surface temperature, vapor ionization, lithium plasma parameters and radiation were studied. Detailed thermal analysis was made to study heat flows in the target and their correspondence with experimental observations. Durable operation of the setup was possible in the range 1-20 MW/m{sup 2} without damage of the structure. The relevance of the experimental performance to divertor condition is analyzed.

  12. Conversion of eugenol to methyleugenol: Computational study and experimental

    Science.gov (United States)

    Kurniawan, Muhammad Arsyik; Matsjeh, Sabirin; Triono, Sugeng

    2017-03-01

    This study provides comprehensive benchmark calculations for the computational study and experimental research on conversion of eugenol to methyleugenol with different pathway of the transition state compounds. First-principle calculation (DFT) were used to generate the structure optimization, energies of species. The calculation parameter are used to predict reactant, product and transition state species as guide to predict the experimental development of chemical characterization method including NMR and IR. The calculation showed significant effect of NaOH in formation of transition state in reaction. Experimentally, the step was nucleophilic substitution reaction of eugenolate ion to dimethylsulfate compound, it was obtained methyleugenol compound with purity of 90.73 %, which analyzed by Infrared and H-NMR spectrometer.

  13. Radiation thermo-chemical models of protoplanetary disks I. Hydrostatic disk structure and inner rim

    NARCIS (Netherlands)

    Woitke, P.; Kamp, I.; Thi, W. -F.

    Context. Emission lines from protoplanetary disks originate mainly in the irradiated surface layers, where the gas is generally warmer than the dust. Therefore, interpreting emission lines requires detailed thermo-chemical models, which are essential to converting line observations into

  14. Enhanced anaerobic digestion of corn stover by thermo-chemical pretreatment

    National Research Council Canada - National Science Library

    Wang Fang; Niu Weisheng; Zhang Andong; Yi Weiming

    2015-01-01

      In order to solve the problem of lignocellulose degraded speedily and efficiently in anaerobic digestion, the thermo-chemical pretreatment was applied to enhance biogas production from corn stover...

  15. Synfuels from fusion: producing hydrogen with the Tandem Mirror Reactor and thermochemical cycles

    Energy Technology Data Exchange (ETDEWEB)

    Werner, R.W.; Ribe, F.L.

    1981-01-21

    This volume contains the following sections: (1) the Tandem Mirror fusion driver, (2) the Cauldron blanket module, (3) the flowing microsphere, (4) coupling the reactor to the process, (5) the thermochemical cycles, and (6) chemical reactors and process units. (MOW)

  16. Experimental study of hole cleaning performance in underbalanced

    African Journals Online (AJOL)

    ADEBOYE

    factors affecting cost, time and drilling quality can be significantly hindered due to poor hole cleaning performance. Experimental study of hole cleaning performance in underbalanced drilling at downhole temperatures260C, 400C and 600C and water influx of 0.25m3/s in a simulated vertical well using gasified mud was ...

  17. An experimental study on effect of process parameters in deep ...

    African Journals Online (AJOL)

    DR OKE

    The effects of various deep drawing process parameters were determined by experimental study with the use of Taguchi fractional factorial .... have used Taguchi method to optimize the turning operation of S45C steel bars using tungsten carbide cutting tools and reported .... The Nd:YAG laser with oxygen cutting gas were.

  18. It Pays to Compare: An Experimental Study on Computational Estimation

    Science.gov (United States)

    Star, Jon R.; Rittle-Johnson, Bethany

    2009-01-01

    Comparing and contrasting examples is a core cognitive process that supports learning in children and adults across a variety of topics. In this experimental study, we evaluated the benefits of supporting comparison in a classroom context for children learning about computational estimation. Fifth- and sixth-grade students (N = 157) learned about…

  19. Experimental studies of the transient fluctuation theorem using liquid ...

    Indian Academy of Sciences (India)

    Home; Journals; Pramana – Journal of Physics; Volume 72; Issue 5. Experimental studies of the transient ... Recently a fluctuation theorem, known as the transient fluctuation theorem (TFT), which generalizes the second law of thermodynamics to small systems has been proposed. This theorem has been tested in small ...

  20. Premium auctions and risk preferences: an experimental study

    NARCIS (Netherlands)

    Brunner, C.; Hu, A.; Oechssler, J.

    2014-01-01

    In premium auctions, the highest losing bidder receives a reward from the seller. This paper studies the private value English premium auction (EPA) for different risk attitudes of bidders. We explicitly derive the symmetric equilibrium for bidders with CARA utilities and conduct an experimental

  1. Sciara as an experimental model for studies on the evolutionary ...

    Indian Academy of Sciences (India)

    Sciara as an experimental model for studies on the evolutionary relationships between the zygotic, maternal and environmental primary signals for sexual development. Lucas Sánchez. Review Article Volume ... Lucas Sánchez1. Centro de Investigaciones Biol´ogicas (C. S. I. C.), Ramiro de Maeztu 9, 28040 Madrid, Spain ...

  2. Experimental Study of Cloud Formation from Rapidly Opened Containers

    Energy Technology Data Exchange (ETDEWEB)

    Wooldridge, C.E. [Stanford Research Institute; Amaro, A.J. [Stanford Research Institute; Kier, R.J. [Stanford Research Institute

    1969-08-01

    This report presents the results of an experimental study of droplet size emanating from a rapidly-opened container of volatile liquid, of the internal dynamics of the cavitation process inside such a container, & of the evaporation time of propane drops.

  3. Experimental study in natural convection | Ousmane | Global Journal ...

    African Journals Online (AJOL)

    The study of thermal and ventilation parameters, obtained in a transient, laminar solar chimney of reduced dimensions, (1 < m <3) m with a square collector (side = 2m) is presented. Experimental measurements has been made to determine the temperature of the absorber and the fluid in the collector, it is shown that at the ...

  4. Synthesis, experimental and theoretical studies of two cocrystals in 1 ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Chemical Sciences; Volume 127; Issue 11. Synthesis, experimental and theoretical studies of two cocrystals in 1:1 stoichiometric ratio from 4,4'-bithiazole-2,2'-diamine with two hydrogen acceptor molecules. Zohreh Rashidi Ranjbar Ali Morsali. Articles Volume 127 Issue 11 November 2015 pp ...

  5. Experimental studies on an indigenous coconut shell based ...

    Indian Academy of Sciences (India)

    Satyabrata Sahoo

    Abstract. Experimental studies are carried out to characterize an indigenous, coconut shell based, activated carbon suitable for storage of natural gas. Properties such as BET surface area, micropore volume, average pore diameter and pore size distribution are obtained by using suitable instruments and techniques.

  6. Experimental Study on a Rotor for WEPTOS Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter; Marchalot, Tanguy

    This report presents the results of an experimental study of the power conversion capabilities of one single rotor of the WEPTOS wave energy converter. The investigation focuses mainly on defining the optimal weight distribution in the rotor in order to improve the hydraulic performance through...

  7. Real versus Simulated Mobile Phone Exposures in Experimental Studies

    Directory of Open Access Journals (Sweden)

    Dimitris J. Panagopoulos

    2015-01-01

    Full Text Available We examined whether exposures to mobile phone radiation in biological/clinical experiments should be performed with real-life Electromagnetic Fields (EMFs emitted by commercially available mobile phone handsets, instead of simulated EMFs emitted by generators or test phones. Real mobile phone emissions are constantly and unpredictably varying and thus are very different from simulated emissions which employ fixed parameters and no variability. This variability is an important parameter that makes real emissions more bioactive. Living organisms seem to have decreased defense against environmental stressors of high variability. While experimental studies employing simulated EMF-emissions present a strong inconsistency among their results with less than 50% of them reporting effects, studies employing real mobile phone exposures demonstrate an almost 100% consistency in showing adverse effects. This consistency is in agreement with studies showing association with brain tumors, symptoms of unwellness, and declines in animal populations. Average dosimetry in studies with real emissions can be reliable with increased number of field measurements, and variation in experimental outcomes due to exposure variability becomes less significant with increased number of experimental replications. We conclude that, in order for experimental findings to reflect reality, it is crucially important that exposures be performed by commercially available mobile phone handsets.

  8. Chemometric Optimization Studies in Catalysis Employing High-Throughput Experimentation

    NARCIS (Netherlands)

    Pereira, S.R.M.

    2008-01-01

    The main topic of this thesis is the investigation of the synergies between High-Throughput Experimentation (HTE) and Chemometric Optimization methodologies in Catalysis research and of the use of such methodologies to maximize the advantages of using HTE methods. Several case studies were analysed

  9. Experimental and modeling studies of mass transfer in ...

    African Journals Online (AJOL)

    Gaining a better understanding of mass transfer problems in encapsulated cell systems and in tissue engineering requires both experimental investigations and mathematical modelling. Specific mass transfer studies are reviewed including oxygen transfer in immobilised animal cell culture systems, modelling of ...

  10. Experimental study of buoyancy driven natural ventilation through horizontal openings

    DEFF Research Database (Denmark)

    Heiselberg, Per; Li, Zhigang

    2007-01-01

    An experimental study of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. Measurements were made for opening ratios L/D range from 0.027 to 4.455, where L and D are the length and the diameter of the opening, respectiv...

  11. An experimental study on effect of process parameters in deep ...

    African Journals Online (AJOL)

    The effects of various deep drawing process parameters were determined by experimental study with the use of Taguchi fractional factorial design and analysis of variance for AA6111 Aluminum alloy. The optimum process parameters were determined based on their influence on the thickness variation at different regions ...

  12. Experimental study on imaging spectrometer focusing formula in orbit

    Science.gov (United States)

    Ma, Hong-tao; Jin, Hui

    2015-02-01

    Experimental verification for a focusing mechanism of imaging spectrometer is studied. The mechanism uses stepper motor driven precision harmonic drive. Wave generator is composed of elliptical cam and a flexible bearing. The output end is connected with the ball screw rotary motion into linear motion, which drives the focusing lens linear guide reciprocating motion. In view of the practical application of the mechanism in the imaging spectrometer, the thermal optical experimental imaging spectrometer has been focusing the formula. Data show that the focus formula ensures linear relationship between the focal plane position and temperature. The linear relationship shows that the imaging spectrometer onboard the variation with temperature and automatic focusing is very important.

  13. Experimental study on beam for composite CES structural system

    Science.gov (United States)

    Matsui, Tomoya

    2017-10-01

    Development study on Concrete Encase Steel (CES) composite structure system has been continuously conducted toward the practical use. CES structure is composed of steel and fiber reinforced concrete. In previous study, it was found that CES structure has good seismic performance from experimental study of columns, beam - column joints, shear walls and a two story two span frame. However, as fundamental study on CES beam could be lacking, it is necessary to understand the structural performance of CES beam. In this study, static loading tests of CES beams were conducted with experimental valuable of steel size, the presence or absence of slab and thickness of slab. And restoring characteristics, failure behavior, deformation behavior, and strength evaluation method of CES beam were investigated. As the results, it was found that CES beam showed stable hysteresis behavior. Furthermore it was found that the flexural strength of the CES beam could be evaluated by superposition strength theory.

  14. Experimental and numerical study on condensation in transonic steam flow

    Directory of Open Access Journals (Sweden)

    Majkut Mirosław

    2015-09-01

    Full Text Available The present paper describes an experimental and numerical study of steam condensing flow in a linear cascade of turbine stator blades. The experimental research was performed on the facility of a small scale steam power plant located at Silesian University of Technology in Gliwice, Poland. The test rig of the facility allows us to perform the tests of steam transonic flows for the conditions corresponding to these which prevail in the low-pressure (LP condensing steam turbine stages. The experimental data of steam condensing flow through the blade-to- blade stator channel were compared with numerical results obtained using the in-house CFD numerical code TraCoFlow. Obtained results confirmed a good quality of the performed experiment and numerical calculations.

  15. Mechanical properties of jennite: A theoretical and experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Juhyuk, E-mail: juhyuk.moon@stonybrook.edu [Civil Engineering Program, Department of Mechanical Engineering, Stony Brook University, NY 11794 (United States); Yoon, Seyoon [School of Engineering, Kings College, University of Aberdeen, Aberdeen AB24 3UE (United Kingdom); Monteiro, Paulo J.M. [Department of Civil and Environmental Engineering, University of California, Berkeley, CA 94720 (United States)

    2015-05-15

    The objective of this study is to determine the mechanical properties of jennite. To date, several hypotheses have been proposed to predict the structural properties of jennite. For the first time as reported herein, the isothermal bulk modulus of jennite was measured experimentally. Synchrotron-based high-pressure x-ray diffraction experiments were performed to observe the variation of lattice parameters under pressure. First-principles calculations were applied to compare with the experimental results and predict additional structural properties. Accurately measured isothermal bulk modulus herein (K{sub 0} = 64(2) GPa) and the statistical assessment on experimental and theoretical results suggest reliable mechanical properties of shear and Young's modulus, Poisson's ratio, and elastic tensor coefficients. Determination of these fundamental structural properties is the first step toward greater understanding of calcium–silicate–hydrate, as well as provides a sound foundation for forthcoming atomic level simulations.

  16. Pseudoepitheliomatous hyperplasia after diode laser oral surgery. An experimental study

    Science.gov (United States)

    Seoane, Juan; González-Mosquera, Antonio; García-Martín, José-Manuel; García-Caballero, Lucía; Varela-Centelles, Pablo

    2015-01-01

    Background To examine the process of epithelial reparation in a surgical wound caused by diode laser. Material and Methods An experimental study with 27 Sprage-Dawley rats was undertaken. The animals were randomly allocated to two experimental groups, whose individuals underwent glossectomy by means of a diode laser at different wattages, and a control group treated using a number 15 scalpel blade. The animals were slaughtered at the 2nd, 7th, and 14th day after glossectomy. The specimens were independently studied by two pathologists (blinded for the specimens’ group). Results At the 7th day, re-epithelisation was slightly faster for the control group (conventional scalpel) (p=0.011). At the 14th day, complete re-epithelization was observed for all groups. The experimental groups displayed a pseudoepitheliomatous hyperplasia. Conclusions It is concluded that, considering the limitations of this kind of experimental studies, early re-epithelisation occurs slightly faster when a conventional scalpel is used for incision, although re-epithelisation is completed in two weeks no matter the instrument used. In addition, pseudoepitheliomatous hyperplasia is a potential event after oral mucosa surgery with diode laser. Knowledge about this phenomenon (not previously described) may prevent diagnostic mistakes and inadequate treatment approaches, particularly when dealing with potentially malignant oral lesions. Key words:Diode laser, animal model, oral biopsy, oral cancer, oral precancer, pseudoepitheliomatous hyperplasia. PMID:26116841

  17. Energetic and environmental assessment of thermochemical and biochemical ways for producing energy from agricultural solid residues: Coffee Cut-Stems case.

    Science.gov (United States)

    García, Carlos A; Peña, Álvaro; Betancourt, Ramiro; Cardona, Carlos A

    2017-04-24

    Forest residues are an important source of biomass. Among these, Coffee Cut-Stems (CCS) are an abundant wood waste in Colombia obtained from coffee crops renovation. However, only low quantities of these residues are used directly in combustion processes for heating and cooking in coffee farms where their energy efficiency is very low. In the present work, an energy and environmental assessment of two bioenergy production processes (ethanol fermentation and gasification) using CCS as raw material was performed. Biomass gasification seems to be the most promising thermochemical method for bioenergy production whereas, ethanol fermentation is a widely studied biochemical method to produce biofuels. Experimental runs of the CCS gasification were carried out and the synthesis gas composition was monitored. Prior to the fermentation process, a treatment of the CCS is required from which sugar content was determined and then, in the fermentation process, the ethanol yield was calculated. Both processes were simulated in order to obtain the mass and energy balance that are used to assess the energy efficiency and the potential environmental impact (PEI). Moderate high energy efficiency and low environmental impacts were obtained from the CCS gasification. In contrast, high environmental impacts in different categories and low energy efficiencies were calculated from the ethanolic fermentation. Biomass gasification seems to be the most promising technology for the use of Coffee Cut-Stems with high energy yields and low environmental issues. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Novel two-step SnO{sub 2}/SnO water-splitting cycle for solar thermochemical production of hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Abanades, Stephane; Charvin, Patrice; Flamant, Gilles [Processes, Materials, and Solar Energy laboratory (PROMES-CNRS, UPR 8521), 7 Rue du Four Solaire, 66120 Font-Romeu (France); Lemont, Florent [Commissariat a l' Energie Atomique (CEA), Rhone Valley Research Center BP17171, 30207 Bagnols-Sur-Ceze Cedex (France)

    2008-11-15

    The production of hydrogen from a novel two-step thermochemical cycle based on SnO{sub 2}/SnO redox reactions is presented. This process targets CO{sub 2}-free hydrogen production by using renewable solar energy and water in a high-temperature water-splitting cycle. The cycle consists of a solar endothermic reduction of SnO{sub 2} into SnO(g) and O{sub 2} followed by a non-solar exothermic hydrolysis of SnO(s) to form H{sub 2} and SnO{sub 2}(s). The objective of this study was to demonstrate this innovative concept for H{sub 2} production and to establish the potential of cycle implementation in an integrated solar chemical process. The reduction and hydrolysis reactions were experimentally tested in order to define optimal operating conditions, chemical conversion and hydrogen yield. The thermal reduction occurs under atmospheric pressure at about 1600 C and over. The solar step encompasses the formation of SnO nanoparticles that can be hydrolysed efficiently in the temperature range 500-600 C with a H{sub 2} yield over 90%. A preliminary process design is also proposed for cycle integration in solar chemical plants. (author)

  19. Accurate fit and thermochemical analysis of the adsorption isotherms of methane in zeolite 13X

    Energy Technology Data Exchange (ETDEWEB)

    Llano-Restrepo, M. [University of Valle, Valle (Colombia). School of Chemical Engineering

    2010-07-01

    The recovery of methane from landfill gases and coal mines has become of the utmost importance because methane has a global-climate warming potential much higher than that of carbon dioxide. Zeolite 13X is widely used for the separation of methane and carbon dioxide from such sources. Accurate fits of the adsorption isotherms of methane in zeolite 13X are required for the rigorous simulation of that separation. In this work, a generalized statistical thermodynamic adsorption (GSTA) model has been used to obtain a very accurate correlation of a published set of adsorption isotherms of methane in zeolite 13X that were measured from 120 K to 273 K over the pressure range 0.07 Pa to 12.2 MPa. In contrast, none of five traditional adsorption models was capable of fitting these isotherms. A thermochemical interpretation of the correlation is provided and predictions for the isosteric heat of adsorption are made, which turn out to be in excellent agreement with the available experimental data.

  20. Experimental Study on Volume for Fly Ash of Building Block

    OpenAIRE

    Ling Wang; He Sun; Zhihui Sun; Enqing Ma

    2013-01-01

    Fly ash is a waste substance from thermal power plants, steel mills, etc. That is found in abundance in the world. It has polluted the environment, wasting the cultivated land. This study introduces an experimental research on fly ash being reused effectively, the study introduces raw materials of fly ash brick, production process and product inspection, fly ash content could be amounted to 40%~75%. High doping fly ash bricks are manufactured, which selects wet fly ash from the power plants, ...

  1. Experimental and Analytical Studies of Solar System Chemistry

    Science.gov (United States)

    Burnett, Donald S.

    2003-01-01

    The cosmochemistry research funded by this grant resulted in the publications given in the attached Publication List. The research focused in three areas: (1) Experimental studies of trace element partitioning. (2) Studies of the minor element chemistry and O isotopic compositions of MgAlO4 spinels from Ca-Al-Rich Inclusions in carbonaceous chondrite meteorites, and (3) The abundances and chemical fractionations of Th and U in chondritic meteorites.

  2. Experimental Studies of the Transport Parameters of Warm Dense Matter

    Energy Technology Data Exchange (ETDEWEB)

    Chouffani, Khalid [Idaho State Univ., Pocatello, ID (United States)

    2014-12-01

    There is a need to establish fundamental properties of matter and energy under extreme physical conditions. Although high energy density physics (HEDP) research spans a wide range of plasma conditions, there is one unifying regime that is of particular importance and complexity: that of warm dense matter, the transitional state between solid state condensed matter and energetic plasmas. Most laboratory experimental conditions, including inertial confinement implosion, fall into this regime. Because all aspects of laboratory-created high-energy-density plasmas transition through the warm dense matter regime, understanding the fundamental properties to determine how matter and energy interact in this regime is an important aspect of major research efforts in HEDP. Improved understanding of warm dense matter would have significant and wide-ranging impact on HEDP science, from helping to explain wire initiation studies on the Sandia Z machine to increasing the predictive power of inertial confinement fusion modeling. The central goal or objective of our proposed research is to experimentally determine the electrical resistivity, temperature, density, and average ionization state of a variety of materials in the warm dense matter regime, without the use of theoretical calculations. Since the lack of an accurate energy of state (EOS) model is primarily due to the lack of experimental data, we propose an experimental study of the transport coefficients of warm dense matter.

  3. Holistic analysis of thermochemical processes by using solid biomass for fuel production in Germany; Ganzheitliche Analyse thermochemischer Verfahren bei der Nutzung fester Biomasse zur Kraftstoffproduktion in Deutschland

    Energy Technology Data Exchange (ETDEWEB)

    Henssler, Martin

    2015-04-28

    According to the German act ''Biokraftstoff-Nachhaltigkeitsverordnung'', biofuels must show a CO{sub 2eq}-reduction compared to the fossil reference fuel (83.8 g CO{sub 2eq}/MJ{sub fuel} /Richtlinie 98/70/EG/) of 35 % beginning with 2011. In new plants, which go into operation after the 31.12.2016 the CO{sub 2eq}-savings must be higher than 50 % in 2017 and higher than 60 % in 2018 /Biokraft-NachV/. The biofuels (methyl ester of rapeseed, bioethanol and biomethane) considered in this study do not meet these requirements for new plants. To comply with these rules new processes must be deployed. Alternative thermochemical generated fuels could be an option. The aim of this work is to evaluate through a technical, ecological and economic analysis (Well-to-Wheel) whether and under what conditions the thermochemical production of Fischer-Tropsch-diesel or -gasoline, hydrogen (H{sub 2}) and Substitute Natural Gas (SNG) complies with the targets. Four different processes are considered (fast pyrolysis and torrefaction with entrained flow gasifier, CHOREN Carbo-V {sup registered} -gasifier, Absorption Enhanced Reforming (AER-) gasifier). Beside residues such as winter wheat straw and residual forest wood, wood from short-rotation plantations is taken into account. The technical analysis showed that at present status (2010) two and in 2050 six plants can be operated energy-self-sufficient. The overall efficiency of the processes is in the range of 41.5 (Fischer-Tropsch-diesel or -gasoline) and 59.4 % (H{sub 2}). Furthermore, it was found that for 2010, all thermochemical produced fuels except the H{sub 2}-production from wood from short-rotation plantations in decentralised or central fast pyrolysis and in decentralised torrefactions with entrained flow gasifier keep the required CO{sub 2eq}-saving of 60 %. In 2050, all thermochemical produced fuels will reach these limits. The CO{sub 2eq}-saving is between 72 (H{sub 2}) and 95 % (Fischer

  4. Experimental and Theoretical Studies in Hydrogen-Bonding Organocatalysis

    Directory of Open Access Journals (Sweden)

    Matej Žabka

    2015-08-01

    Full Text Available Chiral thioureas and squaramides are among the most prominent hydrogen-bond bifunctional organocatalysts now extensively used for various transformations, including aldol, Michael, Mannich and Diels-Alder reactions. More importantly, the experimental and computational study of the mode of activation has begun to attract considerable attention. Various experimental, spectroscopic and calculation methods are now frequently used, often as an integrated approach, to establish the reaction mechanism, the mode of activation or explain the stereochemical outcome of the reaction. This article comprises several case studies, sorted according to the method used in their study. The aim of this review is to give the investigators an overview of the methods currently utilized for mechanistic investigations in hydrogen-bonding organocatalysis.

  5. Optimization of Thermochemical, Kinetic, and Electrochemical Factors Governing Partitioning of Radionuclides During Melt Decontamination of Radioactively Contaminated Stainless Steel

    Energy Technology Data Exchange (ETDEWEB)

    VAN DEN AVYLE,JAMES A.; MALGAARD,DAVID; MOLECKE,MARTIN; PAL,UDAY B.; WILLIAMSON,RODNEY L.; ZHIDKOV,VASILY V.

    1999-06-15

    The Research Objectives of this project are to characterize and optimize the use of molten slags to melt decontaminate radioactive stainless steel scrap metal. The major focus is on optimizing the electroslag remelting (ESR) process, a widely used industrial process for stainless steels and other alloys, which can produce high quality ingots directly suitable for forging, rolling, and parts fabrication. It is our goal to have a melting process ready for a DOE D and D demonstration at the end of the third year of EMSP sponsorship, and this technology could be applied to effective stainless steel scrap recycle for internal DOE applications. It also has potential international applications. The technical approach has several elements: (1) characterize the thermodynamics and kinetics of slag/metal/contaminate reactions by models and experiments, (2) determine the capacity of slags for radioactive containment, (3) characterize the minimum levels of residual slags and contaminates in processed metal, and (4) create an experimental and model-based database on achievable levels of decontamination to support recycle applications. Much of the experimental work on this project is necessarily focused on reactions of slags with surrogate compounds which behave similar to radioactive transuranic and actinide species. This work is being conducted at three locations. At Boston University, Prof. Uday Pal's group conducts fundamental studies on electrochemical and thermochemical reactions among slags, metal, and surrogate contaminate compounds. The purpose of this work is to develop a detailed understanding of reactions in slags through small laboratory scale experiments and modeling. At Sandia, this fundamental information is applied to the design of electroslag melting experiments with surrogates to produce and characterize metal ingots. In addition, ESR furnace conditions are characterized, and both thermodynamic and ESR process models are utilized to optimize the process

  6. Solar Thermochemical Hydrogen Production via Terbium Oxide Based Redox Reactions

    Directory of Open Access Journals (Sweden)

    Rahul Bhosale

    2016-01-01

    Full Text Available The computational thermodynamic modeling of the terbium oxide based two-step solar thermochemical water splitting (Tb-WS cycle is reported. The 1st step of the Tb-WS cycle involves thermal reduction of TbO2 into Tb and O2, whereas the 2nd step corresponds to the production of H2 through Tb oxidation by water splitting reaction. Equilibrium compositions associated with the thermal reduction and water splitting steps were determined via HSC simulations. Influence of oxygen partial pressure in the inert gas on thermal reduction of TbO2 and effect of water splitting temperature (TL on Gibbs free energy related to the H2 production step were examined in detail. The cycle (ηcycle and solar-to-fuel energy conversion (ηsolar-to-fuel efficiency of the Tb-WS cycle were determined by performing the second-law thermodynamic analysis. Results obtained indicate that ηcycle and ηsolar-to-fuel increase with the decrease in oxygen partial pressure in the inert flushing gas and thermal reduction temperature (TH. It was also realized that the recuperation of the heat released by the water splitting reactor and quench unit further enhances the solar reactor efficiency. At TH=2280 K, by applying 60% heat recuperation, maximum ηcycle of 39.0% and ηsolar-to-fuel of 47.1% for the Tb-WS cycle can be attained.

  7. Magnetic reversal frequency scaling in dynamos with thermochemical convection

    Science.gov (United States)

    Olson, Peter; Amit, Hagay

    2014-05-01

    Scaling relationships are derived for the frequency of magnetic polarity reversals in numerical dynamos powered by thermochemical convection. We show that the average number of reversals per unit of time scales with the local Rossby number Rol of the convection. With uniform core-mantle boundary (CMB) heat flux, polarity reversals are absent below a critical value Rol_crit ~ 0.05, beyond which reversal frequency increases approximately linearly with Rol. The relative standard deviation of the dipole intensity fluctuations increases with reversal frequency and Rol. With heterogeneous CMB heat flux that models the large-scale seismic heterogeneity in Earth's lower mantle, reversal frequency also exhibits linear dependence on Rol, and increases approximately as the square root of the amplitude of the CMB heterogeneity. Applied to the history of the geodynamo, these results imply that outer core convection was relatively weak with low CMB heat flux and RolRol_crit during magnetic superchrons and relatively vigorous with higher, more heterogeneous CMB heat flux and Rol>Rol_crit when geomagnetic reversals were frequent. They also suggest that polarity reversals may have been commonplace in the early history of other terrestrial planets. We find that zonal heterogeneity in CMB heat flux produces special effects. Close to Rol_crit, enhanced equatorial cooling at the CMB increases reversal frequency by concentrating magnetic field at low latitudes, whereas far beyond Rol_crit, enhanced polar cooling at the CMB increases reversal frequency by amplifying outer core convection.

  8. Numerical and Experimental Case Study of Blasting Works Effect

    Science.gov (United States)

    Papán, Daniel; Valašková, Veronika; Drusa, Marian

    2016-10-01

    This article introduces the theoretical and experimental case study of dynamic monitoring of the geological environment above constructed highway tunnel. The monitored structure is in this case a very important water supply pipeline, which crosses the tunnel and was made from steel tubes with a diameter of 800 mm. The basic dynamic parameters had been monitored during blasting works, and were compared with the FEM (Finite Element Method) calculations and checked by the Slovak standard limits. A calibrated FEM model based on the experimental measurement data results was created and used in order to receive more realistic results in further predictions, time and space extrapolations. This case study was required and demanded by the general contractor company and also by the owner of water pipeline, and it was an answer of public safety evaluation of risks during tunnel construction.

  9. Lung Morphological Changes in Closed Chest Injury (an experimental study

    Directory of Open Access Journals (Sweden)

    A. M. Golubev

    2012-01-01

    Full Text Available Objective: to study lung morphological changes in a closed chest injury model in laboratory animals. Material and methods. Experiments were carried out in 30 male albino nonbred rats weighing 350—380 g. Closed chest injury was simulated, by exposing the chest of anesthetized rats to a 300-g metal cylinder falling from a height of 30 cm. The observation periods were 1, 3, 6, and 24 hours. Results. The signs of evident perivenular edema that was uncharas-teristic to acute respiratory distress syndrome induced by other causes are an important peculiarity of lung morphological changes in this experimental model of closed chest injury. Conclusion. The experimental studies clarified the pattern of lung morphological changes in the early period after closed chest injury. Key words: closed chest injury, pulmonary edema.

  10. Comparative study of experimental signals for multipactor and breakdown.

    CERN Document Server

    Dehler, Micha; Wuensch, Walter; Faus-Golfe, Angeles; Gimeno Martinez, Benito; Kovermann, Jan; Boria, Vicente; Raboso, David

    2012-01-01

    Performance limiting high-power rf phenomenon occur in both transmitter systems in satellites and high-gradient accelerating structures in particle accelerators. In satellites the predominant effect is multipactor while in accelerators it is breakdown. Both communities have studied their respective phenomena extensively and developed particular simulation tools and experimental techniques. A series of experiments to directly compare measurements made under multipactor and breakdown conditions has been initiated with the objective to crosscheck and compare the physics, simulation tools and measurement techniques.

  11. Experimental and theoretical study of horizontal-axis wind turbines

    OpenAIRE

    Anderson, Michael Broughton

    1981-01-01

    An experimental and theoretical study of horizontal-axis wind turbines is undertaken. The theoretical analyses cover the four major areas of aerodynamics, turbulence. aeroelasticity and blade optimisation. EXisting aerodynamic theories based on blade-element theory for predicting the loads on a wind turbine blade are reviewed and extended to include non-uniform flow, tip losses and the 'turbulent wake' state. A theoretical model based on a free vortex representation of a ...

  12. Composition of intraocular foreign bodies: experimental study of ultrasonographic presentation

    OpenAIRE

    Márcio Augusto Nogueira Costa; Patrícia Novita Garcia; Letícia Fernandes Barroso; Marco Antonio Ferreira; Érika Araki Okuda; Norma Allemann

    2013-01-01

    PURPOSE: To investigate the reliability of ultrasound in determining the size and identify the sonographic features and artifacts generated by intraocular foreign bodies of different materials. METHODS: Experimental study using 36 enucleated porcine eyes. Fragments of nine different compositions (wood, glass, plastic, cardboard, iron, aluminum, lead, powder and concrete) and similar dimensions (4 mm) were implanted via scleral incision into the vitreous cavity of 36 porcine eyes, four eyes we...

  13. Respecifying lab ethnography an ethnomethodological study of experimental physics

    CERN Document Server

    Sormani, Philippe

    2014-01-01

    Respecifying Lab Ethnography delivers the first ethnomethodological study of current experimental physics in action, describing the disciplinary orientation of lab work and exploring the discipline in its social order, formal stringency and skilful performance - in situ and in vivo. In bringing together two major strands of ethnomethodological inquiry, reflexive ethnography and video analysis, which have hitherto existed in parallel, Respecifying Lab Ethnography introduces a practice-based video analysis. In doing so, the book recasts conventional distinctions to shed fresh light on methodolog

  14. Experimental study on durability of small wind turbine

    Science.gov (United States)

    Bao, Daorina; Shang, Wei; Wang, Huan

    2017-06-01

    Through the basic theory of durability test technology for small and medium sized wind power generation units, and the durability of 3KW wind turbine, this paper analyzed the test method of time available rate of unit and studied the power generation capability of the wind turbine. No power attenuation trend has been found, and a lot of experimental data and rich experience in engineering practice has been obtained with the success of experiments.

  15. Experimental studies toward the characterization of Inmetro's circulating water channel

    Science.gov (United States)

    Santos, A. M.; Alho, A. T. P.; Garcia, D. A.; Farias, M. H.; Massari, P. L.; Silva, V. V. S.

    2016-07-01

    Circulating water channels are facilities which can be used for conducting environmental, metrological and engineering studies. The Brazilian National Institute of Metrology-INMETRO has a water channel of innovative design, and the present work deals with the prior experimental investigation of its hydrodynamics performance. By using the optical technique PIV - Particle Image Velocimetry, under certain conditions, the velocity profile behavior in a region inside the channel was analyzed in order to evaluate the scope of applicability of such bench.

  16. Kinetics of uncatalyzed thermochemical sulfate reduction by sulfur-free paraffin

    Science.gov (United States)

    Zhang, Tongwei; Ellis, Geoffrey S.; Ma, Qisheng; Amrani, Alon; Tang, Yongchun

    2012-01-01

    To determine kinetic parameters of sulfate reduction by hydrocarbons (HC) without the initial presence of low valence sulfur, we carried out a series of isothermal gold-tube hydrous-pyrolysis experiments at 320, 340, and 360 °C under a constant confined pressure of 24.1 MPa. The reactants used consisted of saturated HC (sulfur-free) and CaSO4 in an aqueous solution buffered to three different pH conditions without the addition of elemental sulfur (S8) or H2S as initiators. H2S produced in the course of reaction was proportional to the extent of the reduction of CaSO4 that was initially the only sulfur-containing reactant. Our results show that the in situ pH of the aqueous solution (herein, in situ pH refers to the calculated pH value of the aqueous solution at certain experimental conditions) can significantly affect the rate of the thermochemical sulfate reduction (TSR) reaction. A substantial increase in the TSR reaction rate was observed with a decrease in the in situ pH. Our experimental results show that uncatalyzed TSR is a first-order reaction. The temperature dependence of experimentally measured H2S yields from sulfate reduction was fit with the Arrhenius equation. The determined activation energy for HC (sulfur-free) reacting with View the MathML sourceHSO4− in our experiments is 246.6 kJ/mol at pH values ranging from 3.0 to 3.5, which is slightly higher than the theoretical value of 227.0 kJ/mol using ab initio quantum chemical calculations on a similar reaction. Although the availability of reactive sulfate significantly affects the rate of reaction, a consistent rate constant was determined by accounting for the HSO4− ion concentration. Our experimental and theoretical approach to the determination of the kinetics of TSR is further validated by a reevaluation of several published experimental TSR datasets without the initial presence of native sulfur or H2S. When the effect of reactive sulfate concentration is appropriately accounted for, the

  17. Influence of ultrasonic pretreatment on the yield of bio-oil prepared by thermo-chemical conversion of rice husk in hot-compressed water.

    Science.gov (United States)

    Shi, Wen; Jia, Jingfu; Gao, Yahui; Zhao, Yaping

    2013-10-01

    The aim of the current study is to investigate the feasibility of thermo-chemical conversion of rice husk in hot-compressed water via ultrasonic pretreatment to increase the bio-oil yield. The results show that ultrasonic pretreatment remarkably changes the structures of the rice husk, such as enhancing swelling and surface area, eroding lignin structure, and resulting in more exposure of the cellulose and hemicellulose. The highest bio-oil yield of 42.8% was obtained from the thermo-chemical conversion at 300 °C and 0 min of the residence time for the 1 h pretreated rice husk. GC-MS analysis indicates that the relative contents of phenols, 5-Hydroxymethylfurfural, and lactic acid are higher in bio-oils obtained from the pretreated rice husks than that from the raw rice husk. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Survey and Down-Selection of Acid Gas Removal Systems for the Thermochemical Conversion of Biomass to Ethanol with a Detailed Analysis of an MDEA System

    Energy Technology Data Exchange (ETDEWEB)

    Nexant, Inc., San Francisco, California

    2011-05-01

    The first section (Task 1) of this report by Nexant includes a survey and screening of various acid gas removal processes in order to evaluate their capability to meet the specific design requirements for thermochemical ethanol synthesis in NREL's thermochemical ethanol design report (Phillips et al. 2007, NREL/TP-510-41168). MDEA and selexol were short-listed as the most promising acid-gas removal agents based on work described in Task 1. The second report section (Task 2) describes a detailed design of an MDEA (methyl diethanol amine) based acid gas removal system for removing CO2 and H2S from biomass-derived syngas. Only MDEA was chosen for detailed study because of the available resources.

  19. Experimental and numerical studies of two arterial wall delamination modes.

    Science.gov (United States)

    Leng, Xiaochang; Zhou, Boran; Deng, Xiaomin; Davis, Lindsey; Lessner, Susan M; Sutton, Michael A; Shazly, Tarek

    2017-09-19

    Arterial wall dissection, which results from various pathophysiological processes, can lead to the occurrence of large area delamination in the aortic wall that can potentially block blood flow and lead to deleterious clinical conditions. Despite its critical clinical relevance, few studies have focused on investigating the failure mode of delamination in the arterial wall. In this study, we quantify the energy release rate of the medial layer of a porcine abdominal aorta via two delamination experiments: the mixed-mode delamination experiment and the "T"-shaped delamination experiment. A cohesive zone model (CZM) is applied to simulate the arterial wall delamination and Holzapfel-Gasser-Ogden (HGO) material model is used to capture the bulk arterial material behavior. A set of parameter values for the HGO and CZM models are identified through matching simulation predictions of the load vs. load-point displacement curve with experimental measurements. Then the parameter values and critical energy release rates obtained from experiments are used as input data for simulation predictions for two arterial wall delamination experiments. The simulation predictions show that the delamination front matches well with experimental measurements. Moreover, the mixed-mode delamination experiment reveals a shear mode-dominated failure event, whereas the "T"-shaped delamination experiment is an opening failure process. The integration of experimental data and numerical predictions of arterial delamination events provides a comprehensive description of distinct failure modes and aids in the prediction of aortic dissection. Copyright © 2017. Published by Elsevier Ltd.

  20. Analytical and experimental studies of wakes behind circularly capped bubbles

    Science.gov (United States)

    Bessler, W. F.

    The wakes behind circularly capped bubbles are examined by means of an experimental and analytical study. A single two-inch diameter bubble is injected into a six by three foot fluid column, one half inch thick, producing an essentially two-dimensional flow. Aspirin powder placed in the fluid column just prior to bubble release highlights the structure of the flow field before dissolving. High speed film and sequenced photographs are taken to document the observed results. Pressure-time measurements are made with sensitive capacitive transducers mounted in the rear column wall and are synchronized with photographs using a high speed clock. Experimental fluids, prepared by mixing water and glycerine in varying proportions, are used to study the effects of viscosity on bubble shape and wake structure. Testing is performed over a range of Reynolds numbers from 14 to 29,655 which includes the transition from circularly capped to ellipsoidal bubble shape. Experimental data is reduced and summarized in convenient dimensionless form to permit comparison with analytical predictions.

  1. An experimental study on recovering heat from domestic drain water

    Science.gov (United States)

    Ramadan, Mohamad; Al Shaer, Ali; Haddad, Ahmad; Khaled, Mahmoud

    2016-07-01

    This paper concerns an experimental study on a system of heat recovery applied to domestic drain water pipes. The concept suggested consists of using the heat still present in the drain water as a preheating/heating source to the cold water supply of the building. To proceed, an appropriate experimental setup is developed and a coil heat exchanger is used as heat transfer device in the recovery system. Several scenarios are simulated and corresponding parameters are recorded and analyzed. It was shown that the suggested recovery concept can considerably preheat the cold water supply and then decrease the energy consumption. Particularly, up to 8.6 kW of heat were recovered when the cold water supply is initially at 3 °C.

  2. Experimental and theoretical study of metal combustion in oxygen flows

    CERN Document Server

    El-Rabii, Hazem; Muller, Maryse

    2016-01-01

    The effects of oxygen flow speed and pressure on the iron and mild steel combustion are investigated experimentally and theoretically. The studied specimens are vertical cylindrical rods subjected to an axial oxygen flow and ignited at the upper end by laser irradiation. Three main stages of the combustion process have been identified experimentally: (1) Induction period, during which the rod is heated until an intensive metal oxidation begins at its upper end; (2) Static combustion, during which a laminar liquid "cap" slowly grows on the upper rod end; and, after the liquid cap detachment from the sample, (3) Dynamic combustion, which is characterized by a rapid metal consumption and turbulent liquid motions. An analytical description of these stages is given. In particular, a model of the dynamic combustion is constructed based on the turbulent oxygen transport through the liquid metal-oxide flow. This model yields a simple expression for the fraction of metal burned in the process, and allows one to calcul...

  3. Experimental study of effect of stenosis geometry on flow parameters

    Directory of Open Access Journals (Sweden)

    Veselý Ondřej

    2015-01-01

    Full Text Available A stenosis is a narrowing in a tubular organ or structure. In medicine, vessel stenosis poses health risks for people. In this work, experimental investigations of pressure loss coefficient for varying stenosis eccentricity and shape were performed. Five models of different geometry were studied; all models were stenosis of 75 % area reduction. The flow conditions approximate physiological flow. The measuring range of Reynolds number was from 130 to 2730, measured values of pressure loss coefficient were from 12 to 20. The steady experimental results indicated that static pressure loss coefficient is affected by the shape of stenosis, but it was affected more significantly by the eccentricity. Visualization experiments have been performed in Polycarbonate models.

  4. Experimental study of hydronic panels system and its environment

    Energy Technology Data Exchange (ETDEWEB)

    Diaz, Nestor Fonseca [University of Liege Belgium, Thermodynamics Laboratory, Campus du Sart Tilman, Bat: B49 - P33, B-4000 Liege (Belgium); Universidad Tecnologica de Pereira, Facultad de Ingenieria Mecanica (Colombia)

    2011-01-15

    An experimental analysis of hydronic cooling or heating ceiling panels coupled to the building is present in this investigation as a part of the commissioning study of this system. Two test chambers are adapted in a way to reproduce the interaction of the system to the building (windows, internal thermal loads distribution, building structure and ventilation). A series of experimental tests were performed in which the main objective is to observe the influence of parameters such as the water mass flow rate, supply water temperature, thermal load distribution, window and ventilation system effects on the hydronic ceiling capacity and comfort conditions. Test results show that the influence of asymmetric surfaces temperatures inside the room, especially the window effect is not negligible. Then, it is clear that the cooling hydronic ceiling must be evaluated coupled to the building systems and structure. (author)

  5. Experimental study of hydronic panels system and its environment

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca Diaz, Nestor, E-mail: nestorfonseca5@hotmail.co [University of Liege Belgium, Thermodynamics Laboratory, Campus du Sart Tilman, Bat: B49 - P33, B-4000 Liege (Belgium); Universidad Tecnologica de Pereira, Facultad de Ingenieria Mecanica (Colombia)

    2011-01-15

    An experimental analysis of hydronic cooling or heating ceiling panels coupled to the building is present in this investigation as a part of the commissioning study of this system. Two test chambers are adapted in a way to reproduce the interaction of the system to the building (windows, internal thermal loads distribution, building structure and ventilation). A series of experimental tests were performed in which the main objective is to observe the influence of parameters such as the water mass flow rate, supply water temperature, thermal load distribution, window and ventilation system effects on the hydronic ceiling capacity and comfort conditions. Test results show that the influence of asymmetric surfaces temperatures inside the room, especially the window effect is not negligible. Then, it is clear that the cooling hydronic ceiling must be evaluated coupled to the building systems and structure.

  6. Experimental study of heat transfer to falling liquid films

    Science.gov (United States)

    Fagerholm, N. E.; Kivioja, K.; Ghazanfari, A. R.; Jaervinen, E.

    1985-12-01

    This project was initiated in order to obtain more knowledge about thermal design of falling film heat exchangers and to find methods to improve heat transfer in film flow. A short literature survey of film flow characteristics and heat transfer is presented. An experimental apparatus designed and built for studying falling film evaporation is described. The first experiments were made with smooth Cu tube 25/22 mm and refrigerant R114 as evaporating liquid. A significant amount of droplet entrainment was observed during the tests. The measured average heat transfer coefficient varied from 1000 to 1800 W/m K when Re=1300 to 11000 respectively and when the transfer mode is surface evaporation. This could be predicted accurately with the experimental correlation of Chun and Seban. When nucleate boiling is dominant the heat transfer could be predicted well with pool boiling correlation of VDI-84.

  7. Dynamics and structure of thermo-chemical mantle plumes: Are numerical models consistent with observations?

    Science.gov (United States)

    Dannberg, J.; Sobolev, S. V.

    2013-12-01

    According to widely accepted models, plumes ascend from the core-mantle boundary and cause massive melting when they reach the base of the lithosphere. Most of these models consider plumes as purely thermal and predict flattening of the plume head to a disk-like structure, thin plume tails with a radius on the scale of 100 km and kilometer-scale topographic uplift before and during the eruption of flood basalts. However, several paleogeographic and paleotectonic field studies indicate significantly smaller surface uplift during the development of many LIPs, and seismic imaging reveals thicker plume tails as well as a more complex plume structure in the upper mantle including broad low-velocity anomalies up to 400 km depth and elongated low-velocity fingers. Moreover, geochemical data indicate a plume composition that differs from that of the average mantle and recent geodynamic models of plumes in the upper mantle show that plumes containing a large fraction of eclogite and therefore having very low buoyancy can explain the observations much better. Nevertheless, the question remains how such a low-buoyancy plume can rise through the whole mantle and how this ascent affects its dynamics. We perform numerical experiments in 2D axisymmetric geometry to systematically study the dynamics of the plume ascent as well as 2D and 3D models with prescribed velocity at the upper boundary to investigate the interaction between plume- and plate-driven flow. For that purpose, we use modified versions of the finite-element codes Citcom and Aspect. Our models employ complex material properties incorporating phase transitions with the accompanying density changes, Clapeyron slopes and latent heat effects for the peridotite and eclogite phase, mantle compressibility and a highly temperature- and depth-dependent viscosity. We study under which conditions (excess temperature, plume volume and eclogite content) thermo-chemical plumes can ascend through the whole mantle and what

  8. Experimental Study on the WavePiston Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter; Angelelli, E.

    This report presents the results of an experimental study of the power performance of the WavePiston wave energy converter. It focuses mainly on evaluating the power generating capabilities of the device and the effect of the following issues: Scaling ratios PTO loading Wave height and wave period...... dependency Oblique incoming waves Distance between plates During the study, the model supplied by the client, WavePiston, has been rigorously tested as all the anticipated tests have been done thoroughly and during all tests, good quality data has been obtained from all the sensors....

  9. Game theory and experimental games the study of strategic interaction

    CERN Document Server

    Colman, Andrew M

    1982-01-01

    Game Theory and Experimental Games: The Study of Strategic Interaction is a critical survey of the essential ideas of game theory and the findings of empirical research on strategic interaction. Some experiments using lifelike simulations of familiar kinds of strategic interactions are presented, and applications of game theory to the study of voting, the theory of evolution, and moral philosophy are discussed.Comprised of 13 chapters, this volume begins with an informal definition of game theory and an outline of the types of social situations to which it applies. Games of skill, games of cha

  10. Experimental Study of Axially Tension Cold Formed Steel Channel Members

    Science.gov (United States)

    Apriani, Widya; Lubis, Fadrizal; Angraini, Muthia

    2017-12-01

    Experimental testing is commonly used as one of the steps to determine the cause of the collapse of a building structure. The collapse of structures can be due to low quality materials. Although material samples have passed laboratory tests and the existing technical specifications have been met but there may be undetected defects and known material after failure. In this paper will be presented Experimental Testing of Axially Tension Cold Formed Steel Channel Members to determine the cause of the collapse of a building roof truss x in Pekanbaru. Test of tensile strength material cold formed channel sections was performed to obtain the main characteristics of Cold Formed steel material, namely ultimate tensile strength loads that can be held by members and the yield stress possessed by channel sections used in construction. Analysis of axially tension cold formed steel channel section presents in this paper was conducted through experimental study based on specificationsAnnualBook of ASTM Standards: Metal Test methods and Analitical Procedures, Section 3 (1991). The result of capacity loads experimental test was compared with design based on SNI 03-7971-2013standard of Indonesia for the design of cold formed steel structural members. The results of the yield stress of the material will be seen against the minimum allowable allowable stress range. After the test, the percentace of ultimate axial tension capacity theory has a result that is 16.46% larger than the ultimate axial tension capacity experimental. When compared with the load that must be borne 5.673 kN/m it can be concluded that 2 specimens do not meet. Yield stress of member has fulfilled requirement that wass bigger than 550 MPa. Based on the curve obtained ultimate axial tension capacity theory, results greater than experimental. The greatest voltage value (fu) is achieved under the same conditions as its yield stress. For this specimen with a melting voltage value fy = 571.5068 MPa has fulfilled the

  11. Manipulation of pain catastrophizing: An experimental study of healthy participants

    Directory of Open Access Journals (Sweden)

    Joel E Bialosky

    2008-11-01

    Full Text Available Joel E Bialosky1*, Adam T Hirsh2,3, Michael E Robinson2,3, Steven Z George1,3*1Department of Physical Therapy; 2Department of Clinical and Health Psychology; 3Center for Pain Research and Behavioral Health, University of Florida, Gainesville, Florida, USAAbstract: Pain catastrophizing is associated with the pain experience; however, causation has not been established. Studies which specifically manipulate catastrophizing are necessary to establish causation. The present study enrolled 100 healthy individuals. Participants were randomly assigned to repeat a positive, neutral, or one of three catastrophizing statements during a cold pressor task (CPT. Outcome measures of pain tolerance and pain intensity were recorded. No change was noted in catastrophizing immediately following the CPT (F(1,84 = 0.10, p = 0.75, partial η2 < 0.01 independent of group assignment (F(4,84 = 0.78, p = 0.54, partial η2 = 0.04. Pain tolerance (F(4 = 0.67, p = 0.62, partial η2 = 0.03 and pain intensity (F(4 = 0.73, p = 0.58, partial η2 = 0.03 did not differ by group. This study suggests catastrophizing may be difficult to manipulate through experimental pain procedures and repetition of specific catastrophizing statements was not sufficient to change levels of catastrophizing. Additionally, pain tolerance and pain intensity did not differ by group assignment. This study has implications for future studies attempting to experimentally manipulate pain catastrophizing.Keywords: pain, catastrophizing, experimental, cold pressor task, pain catastrophizing scale

  12. Thermal tests of a multi-tubular reactor for hydrogen production by using mixed ferrites thermochemical cycle

    Science.gov (United States)

    Gonzalez-Pardo, Aurelio; Denk, Thorsten; Vidal, Alfonso

    2017-06-01

    The SolH2 project is an INNPACTO initiative of the Spanish Ministry of Economy and Competitiveness, with the main goal to demonstrate the technological feasibility of solar thermochemical water splitting cycles as one of the most promising options to produce H2 from renewable sources in an emission-free way. A multi-tubular solar reactor was designed and build to evaluate a ferrite thermochemical cycle. At the end of this project, the ownership of this plant was transferred to CIEMAT. This paper reviews some additional tests with this pilot plant performed in the Plataforma Solar de Almería with the main goal to assess the thermal behavior of the reactor, evaluating the evolution of the temperatures inside the cavity and the relation between supplied power and reached temperatures. Previous experience with alumina tubes showed that they are very sensitive to temperature and flux gradients, what leads to elaborate an aiming strategy for the heliostat field to achieve a uniform distribution of the radiation inside the cavity. Additionally, the passing of clouds is a phenomenon that importantly affects all the CSP facilities by reducing their efficiency. The behavior of the reactor under these conditions has been studied.

  13. Numerical and experimental study in piping system dead legs

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, E.; Barcouda, M.; Rousset, J.L. [Electricite de France (EDF), 78 - Chatou (France). Lab. National d`Hydraulique; Mallez, C.

    1997-12-31

    This paper deals with an experimental and numerical study of the isothermal flow at the junction of a zero flow-rate pipe connected to high Reynolds number piping system. The motivation is to understand and model the hydraulic behaviour of various auxiliary lines connected to the primary circuit of Pressurised Water Reactors. Experimental data have been obtained on a hydraulic mock-up using flow visualisation method and particle image velocimetry (PIV). These qualitative results show an helicoidal flow extending along the auxiliary pipe. Numerical calculations performed with the 3D ESTET code are presented and contrast the performance of the k-epsilon eddy viscosity model and a second moment closure turbulence model. Fine (1 500 000) mesh were used. The numerical results obtained using the second moment closure turbulence model confirm the swirl flow structure into the dead leg observed on the mock-up. On the other hand the k-epsilon eddy viscosity model is not able to predict the vortex penetration along the auxiliary pipe. These results illustrate the necessity to use second moment closure turbulence model to simulate flows in piping system dead legs. Unfortunately the powerful of the vortex is very sensitive to geometric details of the junction and gives difficulties for quantitative comparisons of the numerical results with experimental data. (author)

  14. Nonlocal Regularized Algebraic Reconstruction Techniques for MRI: An Experimental Study

    Directory of Open Access Journals (Sweden)

    Xin Li

    2013-01-01

    Full Text Available We attempt to revitalize researchers' interest in algebraic reconstruction techniques (ART by expanding their capabilities and demonstrating their potential in speeding up the process of MRI acquisition. Using a continuous-to-discrete model, we experimentally study the application of ART into MRI reconstruction which unifies previous nonuniform-fast-Fourier-transform- (NUFFT- based and gridding-based approaches. Under the framework of ART, we advocate the use of nonlocal regularization techniques which are leveraged from our previous research on modeling photographic images. It is experimentally shown that nonlocal regularization ART (NR-ART can often outperform their local counterparts in terms of both subjective and objective qualities of reconstructed images. On one real-world k-space data set, we find that nonlocal regularization can achieve satisfactory reconstruction from as few as one-third of samples. We also address an issue related to image reconstruction from real-world k-space data but overlooked in the open literature: the consistency of reconstructed images across different resolutions. A resolution-consistent extension of NR-ART is developed and shown to effectively suppress the artifacts arising from frequency extrapolation. Both source codes and experimental results of this work are made fully reproducible.

  15. Experimental Method For Studying Habitual Behavior In Food Consumption

    Directory of Open Access Journals (Sweden)

    Naziha Kasraoui

    2015-03-01

    Full Text Available Abstract To investigate the process of habit formation in everyday life a sample of 126 participants students chooses an eating and drinking for three periods weeks. They completed the self-report habit each period and we have recorded their choices. All participants provided sufficient data for analysis and collected experimental data were examined over the study periods 3 weeks. Experimental analysis was used to examine the persistence of habit formation process in the behavior of participants. The game is carried out with 126 students and repeated for three periods. Using experimental laboratory data approach and economic analysis elasticity results show that into the presence of labor income and for 126 students of whom approximately 70 showed that habit formation process is persist in their behaviors along the three periods. The rest 30 of them who dont present habit formation in their behavior for the three periods did not materially affect our conclusion about the assumption of habit formation process. Participants to the game persistently spend too much in early periods they learn rapidly from their own experience to consume the same choice of meals and drinks. Their spending is closely linked to optimal consumption non conditional on earlier spending and they choose the same basket of goods in the future horizon which shows that theres a habit formation in the behaviors of participants.

  16. The Experimental Study Of Effects Of Irradiation On Osseointegration

    Energy Technology Data Exchange (ETDEWEB)

    Park, Kwan Soo; Lee, Sang Rae; Hwang, Eui Hwan [Dept. of Oral and Maxillofacial Radiology, College of Dentistry, Kyunghee University, Seoul (Korea, Republic of)

    1999-02-15

    The purpose of this study was to investigate the effects of the Co-60 gamma irradiation on the osseointegration. 2.0 mm titanium alloy screw implants were placed in the tibial metaphysics of the rabbits, bilaterally. The mean length of the implants was 6.0 mm. The right tibia was irradiated with a single dose of 15 Gy from 6{sup 0C}o teletherapic machine at 5th postoperative day. The experimental group was irradiated tibia. The control group was non-irradiated tibia. To observe the phase of bone formation, the bone labeling by intramuscular injection of 20 mg/Kg of Tetracycline, Calcein, Alizarin red S, was performed. The rabbits were sacrificed on the 1st, 2nd, 4th, 6th, 8th week and the tibia including implants were taken, and then the specimens were examined by the microradiography, light microscopy, and fluorescent microscopy.The obtained results were as follows; 1. There were connective tissue between bone and titanium at 1st week, in both group. Especially, the many empty lacunae without nucleus and obscure cytoplasm in experimental group, were observed. 2. The osteons were observed at 4th week in control group, and at 6th week in experimental group. The bone formation in experimental group was retarded as compared to the control group. 3. In fluorescent microscopy, bone labelling band was observed as linear, arc or concentric shape. Occasionary interrupted labelling band was observed, which is demonstrated bone remodeling. 4. In microradiographic examination, the radiolucent image was found between bone and implant with widening of bone marrow spaces as compared to the control group.

  17. Study on analyses of experimental data at DCA

    Energy Technology Data Exchange (ETDEWEB)

    Min, Byung Joo; Suk, Ho Chun; Hazama, T. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-11-01

    In this report, the lattice characteristics of DCA are calculated to validate WIMS-AECL code for the lattice analysis of CANDU core by using experimental data of DCA and JNC. These results are compared with those of WIMS-ATR code. Analytical studies of some critical experiments had been performed to analyze the effects of fuel composition and lattice pitch. Different items of reactor physics such as local power peaking factor (LPF), effective multiplication factor (Keff) and coolant void reactivity were calculated for two coolant void fractions (0% and 100%). LPFs calculated by WIMS-ATR code are in close agreement with the experimental results. LPFs calculated by WIMS-AECL code with WINFRITH and ENDF/B-V libraries have similar values for both libraries but the differences between experimental data and results of WIMS-AECL code are larger than those of WIMS-ATR code. The maximum difference between the values calculated by WIMS-ATR and experimental values of LPFs are within 1.3%. LPF of Pu fuel cluster is found to be higher than that of the uranium fuel cluster. The coupled code systems WIMS-ATR and CITATION used in this analysis predict Keff within 1% {delta}K and coolant void reactivity within 4%{delta}K/K in all cases. The coolant void reactivity of uranium fuel is found to be positive for two lattice pitches (25.0 and 28.3 cm). Presence of plutonium fuel makes it more negative compare to uranium fuel. To validate WIMS-AECL code, the core characteristics of DCA shall be calculated by WIMS-AECL and CITATION codes in the future. 8 refs., 8 figs., 12 tabs. (Author)

  18. A thermochemical-biochemical hybrid processing of lignocellulosic biomass for producing fuels and chemicals.

    Science.gov (United States)

    Shen, Yanwen; Jarboe, Laura; Brown, Robert; Wen, Zhiyou

    2015-12-01

    Thermochemical-biological hybrid processing uses thermochemical decomposition of lignocellulosic biomass to produce a variety of intermediate compounds that can be converted into fuels and chemicals through microbial fermentation. It represents a unique opportunity for biomass conversion as it mitigates some of the deficiencies of conventional biochemical (pretreatment-hydrolysis-fermentation) and thermochemical (pyrolysis or gasification) processing. Thermochemical-biological hybrid processing includes two pathways: (i) pyrolysis/pyrolytic substrate fermentation, and (ii) gasification/syngas fermentation. This paper provides a comprehensive review of these two hybrid processing pathways, including the characteristics of fermentative substrates produced in the thermochemical stage and microbial utilization of these compounds in the fermentation stage. The current challenges of these two biomass conversion pathways include toxicity of the crude pyrolytic substrates, the inhibition of raw syngas contaminants, and the mass-transfer limitations in syngas fermentation. Possible approaches for mitigating substrate toxicities are discussed. The review also provides a summary of the current efforts to commercialize hybrid processing. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. Review of the direct thermochemical conversion of lignocellulosic biomass for liquid fuels

    Directory of Open Access Journals (Sweden)

    Jianchun JIANG,Junming XU,Zhanqian SONG

    2015-03-01

    Full Text Available Increased demand for liquid transportation fuels, environmental concerns and depletion of petroleum resources requires the development of efficient conversion technologies for production of second-generation biofuels from non-food resources. Thermochemical approaches hold great potential for conversion of lignocellulosic biomass into liquid fuels. Direct thermochemical processes convert biomass into liquid fuels in one step using heat and catalysts and have many advantages over indirect and biological processes, such as greater feedstock flexibility, integrated conversion of whole biomass, and lower operation costs. Several direct thermochemical processes are employed in the production of liquid biofuels depending on the nature of the feedstock properties: such as fast pyrolysis/liquefaction of lignocellulosic biomass for bio-oil, including upgrading methods, such as catalytic cracking and hydrogenation. Owing to the substantial amount of liquid fuels consumed by vehicular transport, converting biomass into drop-in liquid fuels may reduce the dependence of the fuel market on petroleum-based fuel products. In this review, we also summarize recent progress in technologies for large-scale equipment for direct thermochemical conversion. We focus on the technical aspects critical to commercialization of the technologies for production of liquid fuels from biomass, including feedstock type, cracking catalysts, catalytic cracking mechanisms, catalytic reactors, and biofuel properties. We also discuss future prospects for direct thermochemical conversion in biorefineries for the production of high grade biofuels.

  20. Ceria based inverse opals for thermochemical fuel production: Quantification and prediction of high temperature behavior

    Science.gov (United States)

    Casillas, Danielle Courtney

    Solar energy has the potential to supply more than enough energy to meet humanity's energy demands. Here, a method for thermochemical solar energy storage through fuel production is presented. A porous non-stoichiometric oxide, ceria, undergoes partial thermal reduction and oxidation with concentrated solar energy as a heat source, and water as an oxidant. The resulting yields for hydrogen fuel and oxygen are produced in two discrete steps, while the starting material maintains its original phase. Ordered porosity has been shown superior to random porosity for thermochemical fuel production applications, but stability limits for these structures are currently undefined. Ceria-based inverse opals are currently being investigated to assess the architectural influence on thermochemical hydrogen production. Low tortuosity and continuous interconnected pore network allow for facile gas transport and improved reaction kinetics. Ceria-based ordered materials have recently been shown to increase maximum hydrogen production over non-ordered porous ceria. Thermal stability of ordered porosity was quantified using quantitative image analysis. Fourier analysis was applied to SEM images of the material. The algorithm results in an order parameter gamma that describes the degree of long range order maintained by these structures, where gamma>4 signifies ordered porosity. According to this metric, a minimum zirconium content of 20 atomic percent (at%) is necessary for these architectures to survive aggressive annealing up to 1000°C. Zirconium substituted ceria (ZSC) with Zr loadings in excess of 20at% developed undesired tetragonal phases. Through gamma, we were able to find a balance between the benefit of zirconium additions on structural stability and its negative impact on phase. This work demonstrates the stability of seemingly delicate architectures, and the operational limit for ceria based inverse opals to be 1000°C for 1microm pore size. Inverse opals having sub

  1. Biomass thermochemical conversion - overview of results; Biomassan jalostus - tutkimusalueen katsaus

    Energy Technology Data Exchange (ETDEWEB)

    Sipilae, K. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1995-12-31

    In this Bioenergy research program the thermochemical conversion activities are mainly concentrated in three fields (1) flash pyrolysis and the use of wood oil in boilers and engines (2) biomass gasification for gas engine power plants and finally (3) conversion of black liquor and extractives in a pulp mill to various liquid fuels. Parallel to activities in Finland also significant work has been done in EU-Joule and Apas projects and in the IEA Bioenergy Agreement. In the area of flash pyrolysis technology, three new laboratory and PDU-units have been installed to VTT in order to produce various qualities of bio oils from wood and straw. The quality of pyrolysis oils have been characterized by physical and chemical methods supported by EU and IEA networks. Several companies are carrying out pyrolysis activities as well: Neste Oy is testing the wood oil in a 200 kW boiler, Waertsilae Diesel Oy is testing Canadian wood oil in a 1.5 MWe diesel power plant engine and Vapo Oy is carrying out investigations to produce pyrolysis oils in Finland. The biomass gasification coupled to a gas engine is an interesting alternative for small scale power production parallel to existing fluid bed boiler technology. VTT has installed a circulating fluid bed gasifier with advanced gas cleaning system to test various technologies in order to feed the gas to an engine. In order to produce liquid fuels at a pulp mill, the laboratory work has continued using crude soap as a raw material for high pressure liquid phase treatment and atmospheric pyrolysis process. The quality of the oil is like light fuel oil or diesel fuel, possibilities to use it as a lubricant will be investigated

  2. Experimental studies of pion-nucleus interactions at intermediate energies

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-31

    This report summarizes the work on experimental research in intermediate energy nuclear physics carried out at New Mexico State University in 1991 under a great from the US Department of Energy. Most of these studies have involved investigations of various pion-nucleus interactions. The work has been carried out both with the LAMPF accelerator at the Los Alamos National Laboratory and with the cyclotron at the Paul Scherrer Institute (PSI) near Zurich, Switzerland. Part of the experimental work involves measurements of new data on double-charge-exchange scattering, using facilities at LAMPF which we helped modify, and on pion absorption, using a new detector system at PSI that covers nearly the full solid-angle region which we helped construct. Other work involved preparation for future experiments using polarized nuclear targets and a new high-resolution spectrometer system for detecting {pi}{sup 0} mesons. We also presented several proposals for works to be done in future years, involving studies related to pi-mesonic atoms, fundamental pion-nucleon interactions, studies of the difference between charged and neutral pion interactions with the nucleon, studies of the isospin structure of pion-nucleus interactions, and pion scattering from polarized {sup 3}He targets. This work is aimed at improving our understanding of the pion-nucleon interaction, of the pion-nucleus interaction mechanism, and of nuclear structure.

  3. Numerical Analysis on Thermochemical Characteristics of a Hydrogen Iodine Decomposer in Sulfur-Iodine cycle

    Energy Technology Data Exchange (ETDEWEB)

    Lee, T. H.; Lee, K. Y.; Shin, Y. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Choi, J. S.; Choi, J. H. [Korea Maritime and Ocean University, Busan (Korea, Republic of)

    2015-05-15

    In this study, to develop optimum decomposition reactor of HI to apply hydrogen process in thermochemical VHTR-SI cycle, operating characteristics of the HI decomposition reaction were investigated using the CFD code as a commercial program. Several factors, such as hydrogen production, heat of reaction, and temperature distribution, were studied to compare the device performance with that expected for device development. The CFD analysis for HI decomposition simulation was performed by applying the actual operation conditions and HI decomposer design. The hydrogen production depended on the STV ratio. In this study, predicted hydrogen production was 1.12, 1.99, and 3.10 mol/h for STV ratios of 0.3, 0.4, and 0.5, respectively. The hydrogen production at an STV ratio of 0.5 was higher than that at 0.3 by 2 mol/h. The inner temperature of the HI decomposer was studied in the form of contour images at ITC 1-5.

  4. Experimental study of microtabs in smart blades for wind turbines

    OpenAIRE

    Senosiain Suescun, David; Morales Goicoechea, Joseba

    2013-01-01

    The goal of this thesis is to carry out an experimental study of the performance of smart blades reducing extreme and/or cyclic loads for their use in wind turbines. First of all, theoretical research about wind turbines and smart blades was done. Some of this information is explained in the thesis in order to set the background and make it more readable and understandable (Chapters 1 to 3). The next step was to choose a blade profile that would fit well the requirements of ...

  5. Experimental study of temperature effects on air gun signatures

    Energy Technology Data Exchange (ETDEWEB)

    Langhammer, J.; Landroe, M.

    1992-01-01

    The effect of varying the water temperature between 5[sup o]C and 46[sup o]C upon seismic air gun signatures has been studied experimentally. The experiments were carried out in a 850 litres water tank. Increasing the water temperature from 5[sup o]C to 29[sup o]C leads to 10% increase in the primary to bubble ratio, given that the signatures are filtered with a 0-128 Hz high cut filter. The bubble time period increases with 1 ms, or 4 % within the same temperature range. 7 refs., 28 figs., 3 tabs.

  6. A numerical and experimental study of confined swirling jets

    Science.gov (United States)

    Nikjooy, M.; Mongia, H. C.; Samuelsen, G. S.; Mcdonell, V. G.

    1989-01-01

    A numerical and experimental study of a confined strong swirling flow is presented. Detailed velocity measurements are made using a two-component laser Doppler velocimeter (LDV) technique. Computations are performed using a differential second-moment (DSM) closure. The effect of inlet dissipation rate on calculated mean and turbulence fields is investigated. Various model constants are employed in the pressure-strain model to demonstrate their influences on the predicted results. Finally, comparison of the DSM calculations with the algebraic second-monent (ASM) closure results shows that the DSM is better suited for complex swirling flow analysis.

  7. Experimental studies of ionospheric irregularities and related plasma processes

    Science.gov (United States)

    Baker, Kay D.

    1992-01-01

    Utah State University (USU) continued its program of measuring and interpreting electron density and its variations in a variety of ionospheric conditions with the Experimental Studies of Ionospheric Irregularities and Related Plasma Processes program. The program represented a nearly ten year effort to provide key measurements of electron density and its fluctuations using sounding rockets. The program also involved the joint interpretation of the results in terms of ionospheric processes. A complete campaign summary and a brief description of the major rocket campaigns are also included.

  8. Experimental study of flapping jets in a soap film

    Science.gov (United States)

    Lee, Julia; Kim, Ildoo; Mandre, Shreyas

    2015-11-01

    Plateau and Rayleigh's observation and explanation on jet instability have inspired us over the years and there has been a significant advance in understanding the jet dynamics. Here, we present a quasi-two-dimensional experimental study of flapping jets in a soap film. Newtonian and non-Newtonian solutions are injected in a flowing soap film. Thinning, break-ups, and beads-on-a-string of the jets, and axisymmetric vortices shredded from the flapping jets are visualized. We employ PIV of the flow motion around the jets to gain an understanding of the roles of instabilities in the flow.

  9. Experimental study of dynamic stall on Darrieus wind turbine blades

    Science.gov (United States)

    Brochier, G.; Fraunie, P.; Beguier, C.; Paraschivoiu, I.

    1985-12-01

    An experimental study of periodic vortex phenomena was performed on a model of a two straight-bladed Darrieus wind turbine under controlled-rotation conditions in the IMST water tunnel. The main focus of interest was the tip-speed ratios at which dynamic stall appears. Observations of this phenomenon from dye emission and the formation of hydrogen bubbles were made in the form of photographs, film and video recordings. Velocity measurements were obtained using the Laser-Doppler Velocimeter and components of velocity fluctuations could be determined quantitatively.

  10. Experimental and theoretical study on the electrospinning nanoporous fibers process

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jianghui; Si, Na [National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou (China); Xu, Lan, E-mail: lanxu@suda.edu.cn [National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou (China); Nantong Textile Institute of Soochow University, Nantong (China); Tang, Xiaopeng; Song, Yanhua; Sun, Zhaoyang [National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou (China)

    2016-02-15

    Porous materials can be prepared by sol–gel method, hydrothermal synthesis method, electrospinning and other methods. In this paper, electrospun porous nanofibers were prepared by adjusting electrospinning parameters. And the properties of obtained porous nanofiber mats were investigated. Theoretical analysis and experiment research were carried out to research mechanical mechanism of electrospun porous nanofibers, and could be used to optimize and control the porous structure. The theoretical analysis results were further verified according to the experimental data. In addition, Bernoulli equation was used to study the electrospinning “splaying” process. We found the ratio of pore width to pore length was varied along with the variation of the internal pressure of the jet, and the internal pressure of the jet increases with the velocity of the charged jet decreases. - Highlights: • Mechanical mechanism of electrospun porous nanofibers process was studied. • A simplifying gas–liquid two-phase flow model was established. • Bernoulli equation was used to study the electrospinning “splaying” process. • The theoretical results were in good agreement with the experimental data. • The electrospinning parameters affected the surface morphology of charged jet.

  11. EXPERIMENTAL STUDY OF THE PRODUCTION OF SOLAR HYDROGEN IN ALGERIA

    Directory of Open Access Journals (Sweden)

    W. Bendaikha

    2015-08-01

    Full Text Available Hydrogen is a sustainable fuel option and one of the potential solutions for the current energy and environmental problems. In this study hydrogen is produced using a hydrogen generator with a Proton Exchange Membrane (PEM electrolyser. An experimental study is done in the Center of Development of the Renewable Energy, Algiers, Algeria.The experimental device contains essentially a photovoltaic module, a PEM electrolyser, a gasometer and the devices of measures of characteristics of the PEM electrolyser as well as two pyranometers for the horizontal and diffuse global radiance registration. This system in pilots scale is permitted on the one hand, to measured and analyzed the characteristics: of the PEM electrolyser for two different pressures of working (Patm and P=3 bar, on the other hand, to study the volume of hydrogen produces in the time with different sources of electrical power (generator, photovoltaic module, fluorescent lamp, the efficiency for every case is calculated and compared. We present in this paper the variation of the solar hydrogen flow rate produced according to the global radiance and according to the time for a typical day’s of August.

  12. EXPERIMENTAL STUDY OF INFORMAL NORMS OF URBAN COLORISTICS

    Directory of Open Access Journals (Sweden)

    Yulia Alexandrowna Griber

    2017-02-01

    Full Text Available The objective of the study was informal social norms of urban culture. The paper contains the detailed description of the experimental situation and the main steps of the field research, focused on the observance of informal social norms in the sphere of urban coloristics. The experiment was conducted in three districts of Smolensk (Russia – Leninskiy, Zadneprovskiy and Promyshlennyy. Particular attention was paid to the analysis of the results of the field research, including evaluation of reaction of participants (residents of multi-storied houses, breakers of informal norms of urban coloristics (experimenters and casual experiment witnesses (neighbors and passersby. In addition, the accuracy of results “forecasting”, done before the beginning of the experiment, is analyzed. The research was conducted using the methodology of breaking experiment that is one of the most provocative ways of studying informal norms in sociology and social psychology. The experiment allowed to draw a number of important conclusions. It showed that urban coloristics is regulated by strict informal norms, that are not noticed by citizens until a violation occurs. The power of informal norms is significantly underestimated by citizens, and their break causes a negative reaction and protest. The most important contribution to the study of informal norms of urban culture was the comparison of the reaction degree by men and women, by the residents of different districts (central, residential or blue-collar neighborhoods, by different age groups.

  13. Experimental studies of electron-phonon interactions in gallium nitride

    CERN Document Server

    Stanton, N M

    2001-01-01

    This thesis presents an experimental investigation of the electron-phonon interaction in GaN. Bulk epilayers, grown by MBE, and AIGaN/GaN heterostructure grown by MOCVD, have been studied. The energy relaxation rate for hot electrons has been measured over a wide range of temperatures, allowing both acoustic and optic phonon emission to be studied in GaN epilayers. Direct phonon measurements, both studying the emission and absorption processes, have been performed. Detection of phonons emitted when hot electrons relax their excess energy complements the measurements of relaxation rates. Absorption of acoustic phonons by the epilayers, using both fixed and extended metal film phonon sources, allowed investigation into the effectiveness of the 2k sub F cutoff in the low mobility layers. The experimental findings are compared with the predictions of theory. AIGaN/GaN heterostructures were characterised and measurements of the energy relaxation rate in the temperature range 4K-40K obtained. Excellent agreement wi...

  14. Experimental study of friction in aluminium bolted joints

    Directory of Open Access Journals (Sweden)

    Vincenzi N.

    2010-06-01

    Full Text Available This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces versus sixth tightening (spoiled surfaces. The study considers M8x1.25 8.8 galvanized screws.

  15. Catalyst and feedstock effects in the thermochemical conversion of biomass to liquid transportation fuels

    Energy Technology Data Exchange (ETDEWEB)

    Rejai, B.; Agblevor, F.A.; Evans, R.J.; Wang, D.

    1992-05-01

    The thermochemical conversion of biomass feedstocks to liquid transportation fuels can be accomplished by three processes, namely gasification, high-pressure liquefaction, and pyrolysis. In this study, the pyrolysis option is selected which is followed by the catalytic upgrading of pyrolysis vapors to aromatic and olefinic hydrocarbons (PYROCAT process). The aromatics constitute a high-octane gasoline blend, while the olefins can be utilized as feedstocks for various chemicals. The PYROCAT process has been studied in a laboratory-scale fixed-bed catalytic reactor. Consecutive biomass samples were pyrolyzed rapidly in steam at 550{degree}C and atmospheric pressure, and then the pyrolysis vapors were passed over a zeolite catalyst. The catalytic upgrading products were monitored in real-time using molecular-beam mass-spectrometry (MBMS). The yields of major products were estimated from mass-spectral data. Several zeolite catalysts were screened in the upgrading process and promising catalysts with high yields were identified. Feedstocks studied included: the woody biomass species aspen (Populus tremuloides), basswood (Tilia americana), and willow (Salix alba); the three isolated components of wood lignin, xylan and cellulose; and the herbaceous species bagasse (Saccharum spp. hybrid), wheat straw (Triticum aestivum), and Sericea lespedeza (Lespedeza cuneata). 17 refs.

  16. Coupling SPH and thermochemical models of planets: Methodology and example of a Mars-sized body

    Science.gov (United States)

    Golabek, G. J.; Emsenhuber, A.; Jutzi, M.; Asphaug, E. I.; Gerya, T. V.

    2018-02-01

    Giant impacts have been suggested to explain various characteristics of terrestrial planets and their moons. However, so far in most models only the immediate effects of the collisions have been considered, while the long-term interior evolution of the impacted planets was not studied. Here we present a new approach, combining 3-D shock physics collision calculations with 3-D thermochemical interior evolution models. We apply the combined methods to a demonstration example of a giant impact on a Mars-sized body, using typical collisional parameters from previous studies. While the material parameters (equation of state, rheology model) used in the impact simulations can have some effect on the long-term evolution, we find that the impact angle is the most crucial parameter for the resulting spatial distribution of the newly formed crust. The results indicate that a dichotomous crustal pattern can form after a head-on collision, while this is not the case when considering a more likely grazing collision. Our results underline that end-to-end 3-D calculations of the entire process are required to study in the future the effects of large-scale impacts on the evolution of planetary interiors.

  17. Experimental Studies of Phase Equilibria of Meteorites and Planetary Bodies

    Science.gov (United States)

    Stolper, Edward M.

    2005-01-01

    The primary theme of this project was the application of experimental petrology and geochemistry to a variety of problems in meteoritics and planetary geology. The studies were designed to help develop constraints on the histories of primitive meteorites and their components, the environments in which they formed and evolved, and to understand quantitatively the processes involved in the evolution of igneous rocks on the earth and other planetary bodies. We undertook several projects relating to the origin of CAIs and chondrules. Systematics in the thermodynamic properties of CAI-like liquids were investigated and used to elucidate speciation of multi-valent cations and sulfide capacity of silicate melts and to constrain redox conditions and the vapor pressures of volatile species over molten chondrules. We experimentally determined vanadium speciation in meteoritic pyroxenes and in pyroxenes crystallized from CAI-like melts under very reducing conditions. We also found that bulk oxygen isotope compositions of chondrules in the moderately unequilibrated LL chondrites are related to the relative timing of plagioclase crystallization. We completed an experimental study on the vaporization of beta-SiC and SiO2 (glass or cristobalite) in reducing gases and established the conditions under which these presolar grains could have survived in the solar nebula. We expanded our technique for determining the thermodynamic properties of minerals and liquids to iron-bearing systems. We determined activity-composition relationships in Pt-Fe, Pt-Cr and Pt-Fe-Cr alloys. Results were used to determine the thermodynamic properties of chromite-picrochromite spinels including the free energy of formation of end-member FeCr2O4. We also established a new approach for evaluating Pt-Fe saturation experiments. We calculated the T-fO2 relationships in equilibrated ordinary chondrites and thereby constrained the conditions of metamorphism in their parent bodies.

  18. Immunotoxicology of arc welding fume: worker and experimental animal studies.

    Science.gov (United States)

    Zeidler-Erdely, Patti C; Erdely, Aaron; Antonini, James M

    2012-01-01

    Arc welding processes generate complex aerosols composed of potentially hazardous metal fumes and gases. Millions of workers worldwide are exposed to welding aerosols daily. A health effect of welding that is of concern to the occupational health community is the development of immune system dysfunction. Increased severity, frequency, and duration of upper and lower respiratory tract infections have been reported among welders. Specifically, multiple studies have observed an excess mortality from pneumonia in welders and workers exposed to metal fumes. Although several welder cohort and experimental animal studies investigating the adverse effects of welding fume exposure on immune function have been performed, the potential mechanisms responsible for these effects are limited. The objective of this report was to review both human and animal studies that have examined the effect of welding fume pulmonary exposure on local and systemic immune responses.

  19. Experimental and trial-based study of Resilient Packet Ring

    Science.gov (United States)

    Ramnath, Vasudha; Cheng, Heng Seng; Ngoh, Lek Heng

    2002-08-01

    An experimental study of the Resilient Packet Ring (RPR) media access control (MAC) technology that is optimized for IP traffic in the metropolitan-area-network (MAN) environment is described. The study involved the deployment and trials of a RPR testbed encompassing a public optical fiber infrastructure in which Cisco Systems' Dynamic Packet Transport (DPT) Ring Technology - a prestandard RPR implementation - was used. We focus on a number of important RPR protocol features that are vital to the future success of RPR as a MAN/wide-area-network (WAN) network technology. Related research on RPR/DPT has been done so far through simulation studies only. Standardization of RPR is currently being performed by the Institute of Electrical and Electronics Engineers (IEEE) 802.17 working group and is expected to be completed in 2003. Also, we present and discuss the experiments and tests performed to investigate the key features of RPR, along with the results obtained.

  20. Immunotoxicology of arc welding fume: Worker and experimental animal studies

    Science.gov (United States)

    Zeidler-Erdely, Patti C.; Erdely, Aaron; Antonini, James M.

    2015-01-01

    Arc welding processes generate complex aerosols composed of potentially hazardous metal fumes and gases. Millions of workers worldwide are exposed to welding aerosols daily. A health effect of welding that is of concern to the occupational health community is the development of immune system dysfunction. Increased severity, frequency, and duration of upper and lower respiratory tract infections have been reported among welders. Specifically, multiple studies have observed an excess mortality from pneumonia in welders and workers exposed to metal fumes. Although several welder cohort and experimental animal studies investigating the adverse effects of welding fume exposure on immune function have been performed, the potential mechanisms responsible for these effects are limited. The objective of this report was to review both human and animal studies that have examined the effect of welding fume pulmonary exposure on local and systemic immune responses. PMID:22734811

  1. Design of an experimental set up for convective drying: experimental studies at different drying temperature

    Science.gov (United States)

    Mohan, V. P. Chandra; Talukdar, Prabal

    2013-01-01

    An experimental setup is designed to investigate the convective drying of moist object experimentally. All the design data, components of setup, materials and specifications are presented. Transient moisture content of a rectangular shaped potato slice (4 × 2 × 2 cm) is measured at different air temperatures of 40, 50, 60 and 70 °C with an air velocity of 2 m/s. Two different drying rate periods are observed. Results are compared with available results from literature.

  2. Biofouling in forward osmosis systems: An experimental and numerical study

    KAUST Repository

    Bucs, Szilard

    2016-09-20

    This study evaluates with numerical simulations supported by experimental data the impact of biofouling on membrane performance in a cross-flow forward osmosis (FO) system. The two-dimensional numerical model couples liquid flow with solute transport in the FO feed and draw channels, in the FO membrane support layer and in the biofilm developed on one or both sides of the membrane. The developed model was tested against experimental measurements at various osmotic pressure differences and in batch operation without and with the presence of biofilm on the membrane active layer. Numerical studies explored the effect of biofilm properties (thickness, hydraulic permeability and porosity), biofilm membrane surface coverage, and biofilm location on salt external concentration polarization and on the permeation flux. The numerical simulations revealed that (i) when biofouling occurs, external concentration polarization became important, (ii) the biofilm hydraulic permeability and membrane surface coverage have the highest impact on water flux, and (iii) the biofilm formed in the draw channel impacts the process performance more than when formed in the feed channel. The proposed mathematical model helps to understand the impact of biofouling in FO membrane systems and to develop possible strategies to reduce and control biofouling. © 2016 Elsevier Ltd

  3. Experimental and numerical studies of rotating drum grate furnace

    Directory of Open Access Journals (Sweden)

    Basista Grzegorz

    2017-01-01

    Full Text Available Waste material from the meat industry can be taken into account as a biofuel. Studies confirm, that calorific value is higher and ash content is lower comparing to some conventional fuels. EU directives regulate details of thermal disposal of the waste material from the meat industry - especially in range of the process temperature and time of the particle presence in area of the combustion zone. The paper describes design of the rotating drum grate stove, dedicated to thermal disposal of the meat wastes as well as solid biomass (pellet, small bricket, wood chips combustion. Device has been developed in frames of cooperation between AGH University of Science and Technology (Krakow, Poland and producer focused on technologies of energy utilization of biomass in distributed generation. Results of measurements of selected operational parameters performed during startup of the furnace have been presented and discussed. Furthermore, numerical model of the combustion process has been developed to complement experimental results in range of the temperature and oxygen distribution in the area of the combustion chamber. ANSYS CFX solver has been applied to perform simulations including rotational domain related with specifics of operation of the device. Results of numerical modelling and experimental studies have been summarized and compared.

  4. Experimental studies of irradiated and hydrogen implantation damaged reactor steels

    Energy Technology Data Exchange (ETDEWEB)

    Slugeň, Vladimír, E-mail: vladimir.slugen@stuba.sk; Pecko, Stanislav; Sojak, Stanislav

    2016-01-15

    Radiation degradation of nuclear materials can be experimentally simulated via ion implantation. In our case, German reactor pressure vessel (RPV) steels were studied by positron annihilation lifetime spectroscopy (PALS). This unique non-destructive method can be effectively applied for the evaluation of microstructural changes and for the analysis of degradation of reactor steels due to neutron irradiation and proton implantation. Studied specimens of German reactor pressure vessel steels are originally from CARINA/CARISMA program. Eight specimens were measured in as-received state and two specimens were irradiated by neutrons in German experimental reactor VAK (Versuchsatomkraftwerk Kahl) in the 1980s. One of the specimens which was in as-received and neutron irradiated condition was also used for simulation of neutron damage by hydrogen nuclei implantation. Defects with the size of about 1–2 vacancies with relatively small contribution (with intensity on the level of 20–40 %) were observed in “as-received” steels. A significant increase in the size of the induced defects due to neutron damage was observed in the irradiated specimens resulting in 2–3 vacancies. The size and intensity of defects reached a similar level as in the specimens irradiated in the nuclear reactor due to the implantation of hydrogen ions with energies of 100 keV (up to the depth <500 nm).

  5. Experimental Study of a Pulse Detonation Engine Driven Ejector

    Science.gov (United States)

    Santoro, Robert J.; Pal, Sibtosh; Shehadeh, R.; Saretto, S.; Lee, S.-Y.

    2005-01-01

    Results of an experimental effort on pulse detonation driven ejectors are presented and discussed. The experiments were conducted using a pulse detonation engine (PDE)/ejector setup that was specifically designed for the study. The results of various experiments designed to probe different aspects of the PDE/ejector setup are reported. The baseline PDE was operated using ethylene (C2H4) as the fuel and an oxygen/nitrogen (O2 + N2) mixture at an equivalence ratio of one. The PDE only experiments included propellant mixture characterization using a laser absorption technique, high fidelity thrust measurements using an integrated spring-damper system, and shadowgraph imaging of the detonation/shock wave structure emanating from the tube. The baseline PDE thrust measurement results are in excellent agreement with experimental and modeling results reported in the literature. These PDE setup results were then used as a basis for quantifying thrust augmentation for various PDE/ejector setups with constant diameter ejector tubes and various detonation tube/ejector tube overlap distances. The results show that for the geometries studied here, a maximum thrust augmentation of 24% is achieved. Further increases are possible by tailoring the ejector geometry based on CFD predictions conducted elsewhere. The thrust augmentation results are complemented by shadowgraph imaging of the flowfield in the ejector tube inlet area and high frequency pressure transducer measurements along the length of the ejector tube.

  6. Experimental and analytical studies on pedestrian induced footbridge vibrations

    DEFF Research Database (Denmark)

    Gudmundsson, Gudmundur Valur; Ingólfsson, Einar Thór; Einarsson, Baldvin

    2007-01-01

    This paper presents results from experimental study on human-induced vibrations of three lively footbridges in Reykjavik. The project was funded by the Icelandic Public Roads Administration with two main focus areas; validating the FE-models used at the design stage in terms of dynamic characteri......This paper presents results from experimental study on human-induced vibrations of three lively footbridges in Reykjavik. The project was funded by the Icelandic Public Roads Administration with two main focus areas; validating the FE-models used at the design stage in terms of dynamic...... with two equal spans crossing the same highway and was built in 2000. A commercially available finite element program (SAP2000) was used in the design phase to model the bridges. The FE-models were updated after the initial tests in order to have the frequencies and damping of the fundamental vibration...... modes corresponding to the measured values. The models were subsequently used to calculate the predicted acceleration according to the preliminary version of the Eurocode (ENV 1992-2: Concrete bridges) using time-history analysis with a moving load as representative for a single pedestrian. The load...

  7. Biofouling in forward osmosis systems: An experimental and numerical study.

    Science.gov (United States)

    Bucs, Szilárd S; Valladares Linares, Rodrigo; Vrouwenvelder, Johannes S; Picioreanu, Cristian

    2016-12-01

    This study evaluates with numerical simulations supported by experimental data the impact of biofouling on membrane performance in a cross-flow forward osmosis (FO) system. The two-dimensional numerical model couples liquid flow with solute transport in the FO feed and draw channels, in the FO membrane support layer and in the biofilm developed on one or both sides of the membrane. The developed model was tested against experimental measurements at various osmotic pressure differences and in batch operation without and with the presence of biofilm on the membrane active layer. Numerical studies explored the effect of biofilm properties (thickness, hydraulic permeability and porosity), biofilm membrane surface coverage, and biofilm location on salt external concentration polarization and on the permeation flux. The numerical simulations revealed that (i) when biofouling occurs, external concentration polarization became important, (ii) the biofilm hydraulic permeability and membrane surface coverage have the highest impact on water flux, and (iii) the biofilm formed in the draw channel impacts the process performance more than when formed in the feed channel. The proposed mathematical model helps to understand the impact of biofouling in FO membrane systems and to develop possible strategies to reduce and control biofouling. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Thermodynamic and experimental study of UC powders ignition

    Energy Technology Data Exchange (ETDEWEB)

    Le Guyadec, F., E-mail: fabienne.leguyadec@cea.f [Commissariat a l' Energie Atomique CEA-MARCOULE, DEN/DTEC/SDTC/Laboratoire d' Etude des Materiaux en Environnement, BP 17171, 30207 Bagnols sur Ceze (France); Rado, C.; Joffre, S.; Coullomb, S. [Commissariat a l' Energie Atomique CEA-MARCOULE, DEN/DTEC/SDTC/Laboratoire d' Etude des Materiaux en Environnement, BP 17171, 30207 Bagnols sur Ceze (France); Chatillon, C.; Blanquet, E. [SIMAP, Sciences et Ingenierie des Materiaux et Procedes, INPG-CNRS-UJF ENSEEG, BP 75, 38402 St Martin-d' Heres (France)

    2009-09-01

    Mixed plutonium and uranium carbide (UPuC) is considered as a possible fuel material for future nuclear reactors. However, UPuC is pyrophoric and fine powders of UPuC are subject to temperature increase due to oxidation with air and possible ignition during conditioning and handling. In a first approach and to allow easier experimental conditions, this study was undertaken on uranium monocarbide (UC) with the aim to determine safe handling conditions for the production and reprocessing of uranium carbide fuels. The reactivity of uranium monocarbide in oxidizing atmosphere was studied in order to analyze the ignition process. Experimental thermogravimetric analysis (TGA) and differential thermal analysis (DTA) revealed that UC powder obtained by arc melting and milling is highly reactive in air at about 200 deg. C. The phases formed at the various observed stages of the oxidation process were analyzed by X-ray diffraction. At the same time, ignition was analyzed thermodynamically along isothermal sections of the U-C-O ternary diagram and the pressure of the gas produced by the UC + O{sub 2} reaction was calculated. Two possible oxidation schemes were identified on the U-C-O phase diagram and assumptions are proposed concerning the overall oxidation and ignition paths. It is particularly important to understand the mechanisms involved since temperatures as high as 2500 deg. C could be reached, leading to CO(g) production and possibly to a blast effect.

  9. Thermodynamic and experimental study of UC powders ignition

    Science.gov (United States)

    Le Guyadec, F.; Rado, C.; Joffre, S.; Coullomb, S.; Chatillon, C.; Blanquet, E.

    2009-09-01

    Mixed plutonium and uranium carbide (UPuC) is considered as a possible fuel material for future nuclear reactors. However, UPuC is pyrophoric and fine powders of UPuC are subject to temperature increase due to oxidation with air and possible ignition during conditioning and handling. In a first approach and to allow easier experimental conditions, this study was undertaken on uranium monocarbide (UC) with the aim to determine safe handling conditions for the production and reprocessing of uranium carbide fuels. The reactivity of uranium monocarbide in oxidizing atmosphere was studied in order to analyze the ignition process. Experimental thermogravimetric analysis (TGA) and differential thermal analysis (DTA) revealed that UC powder obtained by arc melting and milling is highly reactive in air at about 200 °C. The phases formed at the various observed stages of the oxidation process were analyzed by X-ray diffraction. At the same time, ignition was analyzed thermodynamically along isothermal sections of the U-C-O ternary diagram and the pressure of the gas produced by the UC + O 2 reaction was calculated. Two possible oxidation schemes were identified on the U-C-O phase diagram and assumptions are proposed concerning the overall oxidation and ignition paths. It is particularly important to understand the mechanisms involved since temperatures as high as 2500 °C could be reached, leading to CO(g) production and possibly to a blast effect.

  10. Experimental studies of irradiated and hydrogen implantation damaged reactor steels

    Science.gov (United States)

    Slugeň, Vladimír; Pecko, Stanislav; Sojak, Stanislav

    2016-01-01

    Radiation degradation of nuclear materials can be experimentally simulated via ion implantation. In our case, German reactor pressure vessel (RPV) steels were studied by positron annihilation lifetime spectroscopy (PALS). This unique non-destructive method can be effectively applied for the evaluation of microstructural changes and for the analysis of degradation of reactor steels due to neutron irradiation and proton implantation. Studied specimens of German reactor pressure vessel steels are originally from CARINA/CARISMA program. Eight specimens were measured in as-received state and two specimens were irradiated by neutrons in German experimental reactor VAK (Versuchsatomkraftwerk Kahl) in the 1980s. One of the specimens which was in as-received and neutron irradiated condition was also used for simulation of neutron damage by hydrogen nuclei implantation. Defects with the size of about 1-2 vacancies with relatively small contribution (with intensity on the level of 20-40 %) were observed in "as-received" steels. A significant increase in the size of the induced defects due to neutron damage was observed in the irradiated specimens resulting in 2-3 vacancies. The size and intensity of defects reached a similar level as in the specimens irradiated in the nuclear reactor due to the implantation of hydrogen ions with energies of 100 keV (up to the depth <500 nm).

  11. Constraints on core-mantle boundary topography from models of thermal and thermochemical convection

    Science.gov (United States)

    Deschamps, Frédéric; Rogister, Yves; Tackley, Paul J.

    2018-01-01

    Mantle flow induces dynamic topography at the core-mantle boundary (CMB), with distribution and amplitude that depend on details of the flow. To assess whether observations of CMB topography can give constraints on deep mantle structure, we determine CMB dynamic topography associated with different models of mantle convection, including thermochemical and purely thermal models. We investigate the influence of key controlling parameters, specifically the thermal viscosity ratio (ΔηT) and, for thermochemical models, the density contrast (ΔρC) and viscosity ratio (ΔηC) between primordial and regular materials. In purely thermal models, plume clusters induce positive topography with an amplitude that decreases with increasing ΔηT. In thermochemical models with moderate density contrasts, around 100-200 kg m-3, reservoirs of dense material induce depressions in CMB topography, surrounded by a ridge of positive topography. The average depression depth and ridge height increase with increasing ΔρC and ΔηC, but decrease with increasing ΔηT. We find that for purely thermal models or thermochemical models with ΔρC ˜ 90 kg m-3 and less, the long-wavelength (spherical harmonic degrees up to l = 4) dynamic topography and shear wave velocity anomalies predicted by thermochemical distributions anticorrelate. By contrast, for models with ΔρC ≥ 100 kg m-3 and ΔηC > 1, long-wavelength dynamic topography and shear wave velocity anomalies correlate well. This potentially provides a test to infer the nature, that is, either purely or mostly thermal (ΔρC ≤ 100 kg m-3 m-3) or strongly thermochemical (ΔρC ≥ 100 kg m-3), of the low shear wave velocity provinces observed by global tomographic images. The presence of post-perovskite, provided that its viscosity is similar to that of bridgmanite, does not alter these conclusions.

  12. Experimental study on neon refrigeration system using commercial helium compressor

    Science.gov (United States)

    Ko, Junseok; Kim, Hyobong; Hong, Yong-Ju; Yeom, Hankil; Koh, Deuk-Yong; Park, Seong-Je

    2012-06-01

    In this study, we developed neon refrigeration system using commercial helium compressor which was originally designed for GM cryocooler. We performed this research as precedent study before developing neon refrigeration system for small-scale hydrogen liquefaction system. The developed system is based on precooled Linde-Hampson system with liquid nitrogen as precoolant. Design parameters of heat exchangers are determined from thermodynamic cycle analysis with operating pressure of 2 MPa and 0.4 MPa. Heat exchangers have concentric-tube heat exchanger configuration and orifice is used as Joule- Thomson expansion device. In experiments, pressure, temperature, mass flow rate and compressor input power are measured as charging pressure. With experimental results, the characteristics of heat exchanger, Joule-Thomson expansion and refrigeration effect are discussed. The developed neon refrigeration system shows the lowest temperature of 43.9 K.

  13. Experimental study on a natural circulation driven HPLWR

    Energy Technology Data Exchange (ETDEWEB)

    T' Joen, C.; Rohde, M. [Delft Univ. of Tech., Delft (Netherlands)

    2011-07-01

    The large density change through the core of a supercritical water reactor could be used as the driving force for circulating the coolant. To study such a natural circulation system, a scaled experimental setup was developed using Freon R23. This paper presents the first power-flow measurements for single core heating as well as 3 core heating (HPLWR power distribution) indicating that natural circulation occurs. A numerical model was developed to further study the impact of geometric and system parameters. This model shows good qualitative agreement with the experiment. By further refining the proposed model to include the pressure drop over the heat exchanger, a better quantitative agreement could be obtained. (author)

  14. Reverse running pumps analytical, experimental and computational study: A review

    Energy Technology Data Exchange (ETDEWEB)

    Nautiyal, Himanshu; Varun; Kumar, Anoop [Department of Mechanical Engineering, National Institute of Technology, Hamirpur (India)

    2010-09-15

    A pump can be used as turbine and has good application in micro-hydropower schemes. Pump as turbine (PAT) is one of the best alternatives for fulfilling the energy demands and providing the electricity in remote and rural areas. In this study a review on the work done in the area of pump working as turbine has been explained. Based upon the literature survey, analytical, experimental and computational works on pump as turbine have been discussed. Several methods for predicting the behaviour of pumps in turbine mode have been developed but no method is appropriate for the entire range of specific speeds. Computational fluid dynamics (CFD) is also used to study the reverse operation of centrifugal pumps, but still results are not yet acceptable. (author)

  15. Experimental studies with low transition energy optics in the SPS

    CERN Document Server

    Bartosik, H; Bohl, T; Cettour Cave, S; Esteban Muller, J; Cornelis, K; Papaphilippou, Y; Rumolo, G; Salvant, B; Shaposhnikova, E; Wenninger, J

    2011-01-01

    The optics of the SPS can be tuned to lower transition energy such that the slippage factor at injection is raised by a factor of almost 3. From theory, an increase of the intensity thresholds for transverse mode coupling, longitudinal coupled bunch and longitudinal instabilities due to the loss of Landau damping can be expected. In this paper, experimental studies in the SPS with single bunches of protons with intensities of up to 3.5e11 p/b on the flat bottom and at 450 GeV/c are presented. Longitudinal instabilities were studied with LHC-type beams with 50 ns spacing and injected intensities up to 1.8e11 p/b. The measurements address the increase of intensity thresholds and the achievable transverse emittances in the new low gamma transition optics with respect to the nominal SPS optics. The obtained results are compared with numerical simulations.

  16. Experimental study of rectenna coupling at low power level

    Science.gov (United States)

    Douyère, A.; Alicalapa, F.; Rivière, S.; Luk, J.-D. Lan Sun

    2013-04-01

    The experimental results presented in this paper focus on the performance of a rectenna array by studying the effect of mutual coupling between two rectennas. The measurements in several planes of the space are investigated and used to help us to define the minimum distance for future rectenna arrays that can be used at a low power density level. The single element chosen for the array is composed of a rectifier circuit and a CSPA (Circular Slot Patch Antenna). This study shows that at a distance greater than 6cm (λ/2) between two rectennas in reception, we observe that the DC received voltage is constant in the Y plane, while in the X plane, the DC received voltage remains constant whatever the distance. We deduce that these rectennas are uncoupled in this case. We can consider each rectenna like an independent system.

  17. An experimental study of laser supported hydrogen plasmas

    Science.gov (United States)

    Vanzandt, D. M.; Mccay, T. D.; Eskridge, R. H.

    1984-01-01

    The rudiments of a rocket thruster which receives its enthalpy from an energy source which is remotely beamed from a laser is described. An experimental study now partially complete is discussed which will eventually provide a detailed understanding of the physics for assessing the feasibility of using hydrogen plasmas for accepting and converting this energy to enthalpy. A plasma ignition scheme which uses a pulsed CO2 laser has been developed and the properties of the ignition spark documented, including breakdown intensities in hydrogen. A complete diagnostic system capable of determining plasma temperature and the plasma absorptivity for subsequent steady state absorption of a high power CO2 laser beam are developed and demonstrative use is discussed for the preliminary case study, a two atmosphere laser supported argon plasma.

  18. Experimental Study of the WEPTOS Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter; Marchalot, Tanguy

    This report presents the results of an experimental study on the power conversion capabilities and structural loads of the WEPTOS wave energy converter. The investigation focuses mainly at identifying the performance of the WEPTOS prototype in a wide range of production wave states...... and at the mooring forces and structural bending moments in extreme wave conditions, in order to estimate the performance and structural loads of larger WEPTOS machines being located at various offshore locations of interest. The following aspects were the main subjects of investigation: Performance of the prototype...... under a constant and linear PTO loading, the opening angle of the device, the effect of alterations to the wave conditions, and mooring forces and structural bending moments in production and extreme wave states. During the study, a highly realistic scale model was supplied by the client, WEPTOS, which...

  19. Experimental Study on the Langlee Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter; Weisz, A.

    This report presents the results of an experimental study of the wave energy converting abilities of the Langlee wave energy converter (WEC). It focused mainly on evaluating the power generating capabilities of the device, including investigations of the following issues: Scaling ratiosPTO loadingWave...... height and wave period dependencyOblique incoming waves and directional spreading of waves (3D waves)Damping platesMooring forces and fixed structure setupPitch, surge and heave motion During the study the model supplied by the client (Langlee Wave Power AS) has been heavily instrumented - up to 23...... different instruments was deployed to measure and record data. Tests were performed at scales of 1:30 and 1:20 based on the realized reference wave states....

  20. Experimental Study of the Weptos Wave Energy Converter

    DEFF Research Database (Denmark)

    Pecher, Arthur; Kofoed, Jens Peter; Larsen, Tommy

    2012-01-01

    This paper presents the power performance results of the experimental study of the WEPTOS wave energy converter (WEC). This novel device combines an established and efficient wave energy absorbing mechanism with an adjustable structure that can regulate the amount of incoming wave energy and reduce...... loads in extreme wave conditions. This A-shaped floating structure absorbs the energy in the waves through a multitude of rotors, the shape of which is based on the renowned Salter’s Duck. These rotors pivot around a common axle, one for each leg of the structure, to which the rotors transfer...... the absorbed wave energy and which is connected to a common power take off system (one for each leg). The study investigates the performance of the device in a large range of wave states and estimates the performance in terms of mechanical power available to the power take off system of the WEPTOS WEC for two...

  1. Dynamic transport of suspended sediment by solitary wave: Experimental study

    Science.gov (United States)

    cho, JaeNam; Kim, DongHyun; Hwang, KyuNam; Lee, SeungOh

    2016-04-01

    Solitary waves are able to transport a large amount of suspended sediment when approaching on the beach, which sometimes causes - serious beach erosion, especially in the east and south coastal lines in Korea. But it has rarely been known about the method how to evaluate or estimate the amount of beach erosion caused by solitary waves. Experimental assessment is necessary to comprehend the process of sediment transport on a slope. The prismatic rectangular channel is 12 m long, 0.8 m wide, and 0.75 m high. A sluice gate is applied at prismatic channel in order to produce the solitary waves. Upstream water depth is more than channel water depth and the sluice gate is suddenly opened to simulate conditions of solitary waves. A sand slope with a 1/6 and a sediment thickness is 0.03 m. The experimental sediments are used anthracite (d_50=1.547 mm ,C_u=1.38) and Jumoonjin sand (d_50=0.627 mm ,C_u=1.68). Specific laboratory equipment are designed to collect suspended sediment samples at the same time along the wave propagation at 5 points with evenly space. Each amount of sampling is approximately 25 ml and they are completely dried in oven over 24 hours according to the USGS (Guideline and standard techniques and method 3-C4). Two video cameras (Model No. : Sony, HDR-XR550) are mounted for capturing images at top and side-view when the processes of solitary wave and run up/down on slope. Also, this study are analyzed the correlation between Suspended sediment concentration and turbidity. Also, this study are analyzed the correlation between suspended sediment concentration and turbidity. Turbidity is used to verify suspended sediment concentration. Dimensionless analyses of experimental results carried out in this study. One dimensionless parameter is expressed with pressure of solitary wave on a slope to suspended sediment concentration, which is concerned about lifting force. The other is relate to drag force presenting with run up/down velocity on a slope and

  2. Experimental Study of Current-Driven Turbulence During Magnetic Reconnection

    Energy Technology Data Exchange (ETDEWEB)

    Porkolab, Miklos; Egedal-Pedersen, Jan; Fox, William

    2010-08-31

    CMPD Final Report Experimental Study of Current-Driven Turbulence During Magnetic Reconnection Miklos Porkolab, PI, Jan Egedal, co-PI, William Fox, graduate student. This is the final report for Grant DE-FC02-04ER54786, MIT Participation in the Center for Multiscale Plasma Dynamics, which was active from 8/1/2004 to 7/31/2010. This Grant supported the thesis work of one MIT graduate student, William Fox, The thesis research consisted of an experimental study of the fluctuations arising during magnetic reconnection in plasmas on the Versatile Toroidal Facility (VTF) at MIT Plasma Science and Fusion Center (PSFC). The thesis was submitted and accepted by the MIT physics Department,. Fox, Experimental Study of Current-Driven Turbulence During Magnetic Reconnection, Ph.D. Thesis, MIT (2009). In the VTF experiment reconnection and current-sheet formation is driven by quickly changing currents in a specially arranged set of internal conductors. Previous work on this device [Egedal, et al, PRL 98, 015003, (2007)] identified a spontaneous reconnection regime. In this work fluctuations were studied using impedance-matched, high-bandwidth Langmuir probes. Strong, broadband fluctuations, with frequencies extending from near the lower-hybrid frequency [fLH = (fcefci)1/2] to the electron cyclotron frequency fce were found to arise during the reconnection events. Based on frequency and wavelength measurements, lower-hybrid waves and Trivelpiece-Gould waves were identified. The lower-hybrid waves are easiest to drive with strong perpendicular drifts or gradients which arise due to the reconnection events; an appealing possibility is strong temperature gradients. The Trivelpiece-Gould modes can result from kinetic, bump-on-tail instability of a runaway electron population energized by the reconnection events. We also observed that the turbulence is often spiky, consisting of discrete positive-potential spikes, which were identified as electron phase-space holes, a class of

  3. Approximate thermochemical tables for some C-H and C-H-O species

    Science.gov (United States)

    Bahn, G. S.

    1973-01-01

    Approximate thermochemical tables are presented for some C-H and C-H-O species and for some ionized species, supplementing the JANAF Thermochemical Tables for application to finite-chemical-kinetics calculations. The approximate tables were prepared by interpolation and extrapolation of limited available data, especially by interpolations over chemical families of species. Original estimations have been smoothed by use of a modification for the CDC-6600 computer of the Lewis Research Center PACl Program which was originally prepared for the IBM-7094 computer Summary graphs for various families show reasonably consistent curvefit values, anchored by properties of existing species in the JANAF tables.

  4. Importance of the ligand basis set in ab initio thermochemical calculations of transition metal species

    Science.gov (United States)

    Plascencia, Cesar; Wang, Jiaqi; Wilson, Angela K.

    2017-10-01

    The impact of basis set choice has been considered for a series of transition metal (TM) species. The need for higher level correlation consistent basis sets on both the metal and ligand has been investigated, and permutations in the pairings of basis set used for TM's and basis set used for ligands can lead to effective routes to complete basis set (CBS) limit extrapolations of thermochemical energetics with little change in thermochemical predictions as compared to those resulting from the use of traditional basis set pairings, while enabling computational cost savings. Basis set superposition errors (BSSE) that can arise have also been considered.

  5. Experimental study of visual training effects in shooting initiation.

    Science.gov (United States)

    Quevedo, Lluïsa; Solé, Joan; Palmi, Joan; Planas, Antoni; Soana, Carlos

    1999-01-01

    INTRODUCTION: The present study was conducted to investigate the influence of specific visual training in shooting initiation performance. METHODS: Seventy-one first-year university students were divided randomly into two groups. The experimental group followed a nine-session shooting training program that included technical, physical and psychological components, along with specific visual exercises. The control group followed the same program with one difference: this group received theoretical lectures on psychological training techniques instead of doing visual exercises. Pre- and post-test results were obtained for shooting, concentration, saccades and visual acuity. RESULTS: Statistical analysis indicated significant gains in the four mentioned variables for the experimental group. The control group also showed significant differences in the three first variables but no significant improvement in visual acuity. No significant differences in shooting performance were observed between groups. CONCLUSIONS: The effect of vision training on sports initiation performance is still not clear. It cannot be assumed that the improvement is transferable to the performance of precision shooting at the stage of sports initiation.

  6. Experimental Study of Hysteretic Steel Damper for Energy Dissipation Capacity

    Directory of Open Access Journals (Sweden)

    Daniel R. Teruna

    2015-01-01

    Full Text Available This study aims to evaluate energy absorption capacity of hysteretic steel damper for earthquake protection of structures. These types of steel dampers are fabricated from mild steel plate with different geometrical shapes on the side part, namely, straight, concave, and convex shapes. The performance of the proposed device was verified experimentally by a series of tests under increasing in-plane cyclic load. The overall test results indicated that the proposed steel dampers have similar hysteretic curves, but the specimen with convex-shaped side not only showed stable hysteretic behavior but also showed excellent energy dissipation capabilities and ductility factor. Furthermore, the load-deformation relation of these steel dampers can be decomposed into three parts, namely, skeleton curve, Bauschinger part, and elastic unloading part. The skeleton curve is commonly used to obtain the main parameters, which describe the behavior of steel damper, namely, yield strength, elastic stiffness, and postyield stiffness ratio. Moreover, the effective stiffness, effective damping ratio, cumulative plastic strain energy, and cumulative ductility factor were also derived from the results. Finally, an approximation trilinear hysteretic model was developed based on skeleton curve obtained from experimental results.

  7. Experimental Vertical Stability Studies for ITER Performance and Design Guidance

    Energy Technology Data Exchange (ETDEWEB)

    Humphreys, D A; Casper, T A; Eidietis, N; Ferrera, M; Gates, D A; Hutchinson, I H; Jackson, G L; Kolemen, E; Leuer, J A; Lister, J; LoDestro, L L; Meyer, W H; Pearlstein, L D; Sartori, F; Walker, M L; Welander, A S; Wolfe, S M

    2008-10-13

    Operating experimental devices have provided key inputs to the design process for ITER axisymmetric control. In particular, experiments have quantified controllability and robustness requirements in the presence of realistic noise and disturbance environments, which are difficult or impossible to characterize with modeling and simulation alone. This kind of information is particularly critical for ITER vertical control, which poses some of the highest demands on poloidal field system performance, since the consequences of loss of vertical control can be very severe. The present work describes results of multi-machine studies performed under a joint ITPA experiment on fundamental vertical control performance and controllability limits. We present experimental results from Alcator C-Mod, DIII-D, NSTX, TCV, and JET, along with analysis of these data to provide vertical control performance guidance to ITER. Useful metrics to quantify this control performance include the stability margin and maximum controllable vertical displacement. Theoretical analysis of the maximum controllable vertical displacement suggests effective approaches to improving performance in terms of this metric, with implications for ITER design modifications. Typical levels of noise in the vertical position measurement which can challenge the vertical control loop are assessed and analyzed.

  8. SOLAR VACUUM TUBE INTEGRATED SEAWATER DISTILLATION - AN EXPERIMENTAL STUDY

    Directory of Open Access Journals (Sweden)

    Selcuk Selimli

    2016-04-01

    Full Text Available The subject of this study is the seawater distillation process enhancement through integration of the solar vacuum tube into the system. Positive effects on the rate of distillated freshwater achieved by means of the enhanced system have been investigated experimentally. Experiments were done in the Turkish city of Samsun in the Black Sea region. A distillation pond setup having the volume of 0.015m3 and a water surface area of 0.24m2 was constructed. The distillation pond is covered with a condensation glass and also equipped with a 0.15m solar vacuum tube that is inclined at an angle of 30o to the ground, a feed water tank connected with a ball cock, and distillated fresh water tank. Experimental results have shown that the rate of distilled fresh water was enhanced for about 62.5% by integrating the solar vacuum tube and the natural distillation pond. Isolation of the condensation glass not only prevents the light transmission to the pond but also heat loss from the pond; hence the rate of the distillated fresh water is increased for about 137.5% due to the natural distillation.

  9. Scintigraphic and Radiographic Study of the Experimental Periapical Lesions

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Youn Sik; Park, Tae Won [Dept. of Oral Radiology, College of Dentistry, Seoul National University, Seoul (Korea, Republic of)

    1989-11-15

    The purpose of this study was to clarify that scintigram was a more effective method than radiogram in the early detection of periapical lesion. Periapical lesions were produced artificially by the opening of the pulp chambers of the lower right 3rd and 4th premolars in 6 dogs. The serial bone scintigrams using 99m-Tc-MDP and periapical radiograms were taken weekly. The uptake counts of the 99-Tc-MDP in the experimental side were compared with those in the control side. The periapical radiograms were interpreted with the joint evaluation by three dental radiologists. The following results were obtained.; 1. The radioactivity in the experimental side was increased at the 1st week except one animal in which the radioactivity was increased at the 2nd week. 2. It was observed that increasing amount of radioactivity per week was prominent from the 1st day of experiment to the 1st week, and the 3rd week to the 4th week. 3. The radiographic evidence of the periapical lesions was observed at the 3rd week and became more apparent at the 4th week. 4. Histologically, proliferation of blood vessels and infiltration of chronic inflammatory cells were observed at the 1st week and osteoblasts were found after the 3rd week.

  10. A comprehensive experimental and modeling study of 2-methylbutanol combustion

    KAUST Repository

    Park, Sungwoo

    2015-05-01

    2-Methylbutanol (2-methyl-1-butanol) is one of several next-generation biofuels that can be used as an alternative fuel or blending component for combustion engines. This paper presents new experimental data for 2-methylbutanol, including ignition delay times in a high-pressure shock tube and premixed laminar flame speeds in a constant volume combustion vessel. Shock tube ignition delay times were measured for 2-methylbutanol/air mixtures at three equivalence ratios, temperatures ranging from 750 to 1250. K, and at nominal pressures near 20 and 40. bar. Laminar flame speed data were obtained using the spherically propagating premixed flame configuration at pressures of 1, 2, and 5. bar. A detailed chemical kinetic model for 2-methylbutanol oxidation was developed including high- and low-temperature chemistry based on previous modeling studies on butanol and pentanol isomers. The proposed model was tested against new and existing experimental data at pressures of 1-40. atm, temperatures of 740-1636. K, equivalence ratios of 0.25-2.0. Reaction path and sensitivity analyses were conducted for identifying key reactions at various combustion conditions, and to obtain better understanding of the combustion characteristics of larger alcohols.

  11. Experimental study of moving throat plug in a shock tunnel

    Science.gov (United States)

    Lee, J. K.; Park, C.; Kwon, O. J.

    2015-07-01

    An experimental study has been carried out to investigate the flow in the KAIST shock tunnel with two moving throat plugs at a primary shock velocity of 1.19 km/s. The nozzle reservoir pressure and the Pitot pressure at the exit of the nozzle were measured to examine the influence of the moving throat plugs on the shock tunnel flow. To assess the present experimental results, comparisons with previous work using a stationary throat plug were made. The mechanism for closing the moving throat plug was developed and verified. The source of the force to move the plug was the pressure generated when the primary shock was reflected at the bottom of the plug. It was observed that the two plugs terminated the shock tunnel flow after the steady flow. .The time for the plugs to terminate the flow showed good agreement with the calculation of the proposed simple analytic solution. There was a negligible difference in flow values such as the reflected pressure and the Pitot pressure between the moving and the stationary plugs.

  12. Geochemical signatures of thermochemical sulfate reduction in controlled hydrous pyrolysis experiments

    Science.gov (United States)

    Zhang, T.; Ellis, G.S.; Walters, C.C.; Kelemen, S.R.; Wang, K.-s.; Tang, Y.

    2008-01-01

    A series of gold tube hydrous pyrolysis experiments was conducted in order to investigate the effect of thermochemical sulfate reduction (TSR) on gas generation, residual saturated hydrocarbon compositional alteration, and solid pyrobitumen formation. The intensity of TSR significantly depends on the H2O/MgSO4 mole ratio, the smaller the ratio, the stronger the oxidizing conditions. Under highly oxidizing conditions (MgSO4/hydrocarbon wt/wt 20/1 and hydrocarbon/H2O wt/wt 1/1), large amounts of H2S and CO2 are generated indicating that hydrocarbon oxidation coupled with sulfate reduction is the dominant reaction. Starting with a mixture of C21-C35 n-alkanes, these hydrocarbons are consumed totally at temperatures below the onset of hydrocarbon thermal cracking in the absence of TSR (400 ??C). Moreover, once the longer chain length hydrocarbons are oxidized, secondarily formed hydrocarbons, even methane, are oxidized to CO2. Using whole crude oils as the starting reactants, the TSR reaction dramatically lowers the stability of hydrocarbons leading to increases in gas dryness and gas/oil ratio. While their concentrations decrease, the relative distributions of n-alkanes do not change appreciably from the original composition, and consequently, are non-diagnostic for TSR. However, distinct molecular changes related to TSR are observed, Pr/n-C17 and Ph/n-C18 ratios decrease at a faster rate under TSR compared to thermal chemical alteration (TCA) alone. TSR promotes aromatization and the incorporation of sulfur and oxygen into hydrocarbons leading to a decrease in the saturate to aromatic ratio in the residual oil and in the generation of sulfur and oxygen rich pyrobitumen. These experimental findings could provide useful geochemical signatures to identify TSR in settings where TSR has occurred in natural systems. ?? 2008 Elsevier Ltd. All rights reserved.

  13. Compositional and stable carbon isotopic fractionation during non-autocatalytic thermochemical sulfate reduction by gaseous hydrocarbons

    Science.gov (United States)

    Xia, Xinyu; Ellis, Geoffrey S.; Ma, Qisheng; Tang, Yongchun

    2014-01-01

    The possibility of autocatalysis during thermochemical sulfate reduction (TSR) by gaseous hydrocarbons was investigated by examination of previously reported laboratory and field data. This reaction was found to be a kinetically controlled non-autocatalytic process, and the apparent lack of autocatalysis is thought to be due to the absence of the required intermediate species. Kinetic parameters for chemical and carbon isotopic fractionations of gaseous hydrocarbons affected by TSR were calculated and found to be consistent with experimentally derived values for TSR involving long-chain hydrocarbons. Model predictions based on these kinetic values indicate that TSR by gaseous hydrocarbon requires high-temperature conditions. The oxidation of C2–5 hydrocarbons by sulfate reduction is accompanied by carbon isotopic fractionation with the residual C2–5 hydrocarbons becoming more enriched in 13C. Kinetic parameters were calculated for the stable carbon isotopic fractionation of gaseous hydrocarbons that have experienced TSR. Model predictions based on these kinetics indicate that it may be difficult to distinguish the effects of TSR from those of thermal maturation at lower levels of hydrocarbon oxidation; however, unusually heavy δ13C2+ values (>−10‰) can be diagnostic of high levels of conversion (>50%). Stoichiometric and stable carbon isotopic data show that methane is stable under the investigated reaction conditions and is likely a product of TSR by other gaseous hydrocarbons rather than a significant reactant. These results indicate that the overall TSR reaction mechanism for oxidation of organic substrates containing long-chain hydrocarbons involves three distinct phases as follows: (1) an initial slow and non-autocatalytic stage characterized by the reduction of reactive sulfate by long-chain saturated hydrocarbons; (2) a second autocatalytic reaction phase dominated by reactions involving reduced sulfur species and partially oxidized hydrocarbons; (3

  14. Thermochemical Stability and Friction Properties of Soft Organosilica Networks for Solid Lubrication

    Directory of Open Access Journals (Sweden)

    Pablo Gonzalez Rodriguez

    2018-01-01

    Full Text Available In view of their possible application as high temperature solid lubricants, the tribological and thermochemical properties of several organosilica networks were investigated over a range of temperatures between 25 and 580 °C. Organosilica networks, obtained from monomers with terminal and bridging organic groups, were synthesized by a sol-gel process. The influence of carbon content, crosslink density, rotational freedom of incorporated hydrocarbon groups, and network connectivity on the high temperature friction properties of the polymer was studied for condensed materials from silicon alkoxide precursors with terminating organic groups, i.e., methyltrimethoxysilane, propyltrimethoxysilane, diisopropyldimethoxysilane, cyclohexyltrimethoxysilane, phenyltrimethoxysilane and 4-biphenylyltriethoxysilane networks, as well as precursors with organic bridging groups between Si centers, i.e., 1,4-bis(triethoxysilylbenzene and 4,4′-bis(triethoxysilyl-1,1′-biphenyl. Pin-on-disc measurements were performed using all selected solid lubricants. It was found that materials obtained from phenyltrimethoxysilane and cyclohexyltrimethoxysilane precursors showed softening above 120 °C and performed best in terms of friction reduction, reaching friction coefficients as low as 0.01. This value is lower than that of graphite films (0.050 ± 0.005, a common bench mark for solid lubricants.

  15. Thermochemical Stability and Friction Properties of Soft Organosilica Networks for Solid Lubrication.

    Science.gov (United States)

    Gonzalez Rodriguez, Pablo; Dral, A Petra; van den Nieuwenhuijzen, Karin J H; Lette, Walter; Schipper, Dik J; Ten Elshof, Johan E

    2018-01-24

    In view of their possible application as high temperature solid lubricants, the tribological and thermochemical properties of several organosilica networks were investigated over a range of temperatures between 25 and 580 °C. Organosilica networks, obtained from monomers with terminal and bridging organic groups, were synthesized by a sol-gel process. The influence of carbon content, crosslink density, rotational freedom of incorporated hydrocarbon groups, and network connectivity on the high temperature friction properties of the polymer was studied for condensed materials from silicon alkoxide precursors with terminating organic groups, i.e., methyltrimethoxysilane, propyltrimethoxysilane, diisopropyldimethoxysilane, cyclohexyltrimethoxysilane, phenyltrimethoxysilane and 4-biphenylyltriethoxysilane networks, as well as precursors with organic bridging groups between Si centers, i.e., 1,4-bis(triethoxysilyl)benzene and 4,4'-bis(triethoxysilyl)-1,1'-biphenyl. Pin-on-disc measurements were performed using all selected solid lubricants. It was found that materials obtained from phenyltrimethoxysilane and cyclohexyltrimethoxysilane precursors showed softening above 120 °C and performed best in terms of friction reduction, reaching friction coefficients as low as 0.01. This value is lower than that of graphite films (0.050 ± 0.005), a common bench mark for solid lubricants.

  16. Thermochemical Equilibrium Model of Synthetic Natural Gas Production from Coal Gasification Using Aspen Plus

    Directory of Open Access Journals (Sweden)

    Rolando Barrera

    2014-01-01

    Full Text Available The production of synthetic or substitute natural gas (SNG from coal is a process of interest in Colombia where the reserves-to-production ratio (R/P for natural gas is expected to be between 7 and 10 years, while the R/P for coal is forecasted to be around 90 years. In this work, the process to produce SNG by means of coal-entrained flow gasifiers is modeled under thermochemical equilibrium with the Gibbs free energy approach. The model was developed using a complete and comprehensive Aspen Plus model. Two typical technologies used in entrained flow gasifiers such as coal dry and coal slurry are modeled and simulated. Emphasis is put on interactions between the fuel feeding technology and selected energy output parameters of coal-SNG process, that is, energy efficiencies, power, and SNG quality. It was found that coal rank does not significantly affect energy indicators such as cold gas, process, and global efficiencies. However, feeding technology clearly has an effect on the process due to the gasifying agent. Simulations results are compared against available technical data with good accuracy. Thus, the proposed model is considered as a versatile and useful computational tool to study and optimize the coal to SNG process.

  17. Thermochemical Characterizations of Novel Vermiculite-LiCl Composite Sorbents for Low-Temperature Heat Storage

    Directory of Open Access Journals (Sweden)

    Yannan Zhang

    2016-10-01

    Full Text Available To store low-temperature heat below 100 °C, novel composite sorbents were developed by impregnating LiCl into expanded vermiculite (EVM in this study. Five kinds of composite sorbents were prepared using different salt concentrations, and the optimal sorbent for application was selected by comparing both the sorption characteristics and energy storage density. Textural properties of composite sorbents were obtained by extreme-resolution field emission scanning electron microscopy (ER-SEM and an automatic mercury porosimeter. After excluding two composite sorbents which would possibly exhibit solution leakage in practical thermal energy storage (TES system, thermochemical characterizations were implemented through simulative sorption experiments at 30 °C and 60% RH. Analyses of thermogravimetric analysis/differential scanning calorimetry (TGA/DSC curves indicate that water uptake of EVM/LiCl composite sorbents is divided into three parts: physical adsorption of EVM, chemical adsorption of LiCl crystal, and liquid–gas absorption of LiCl solution. Energy storage potential was evaluated by theoretical calculation based on TGA/DSC curves. Overall, EVMLiCl20 was selected as the optimal composite sorbent with water uptake of 1.41 g/g, mass energy storage density of 1.21 kWh/kg, and volume energy storage density of 171.61 kWh/m3.

  18. Thermochemical pretreatments of organic fraction of municipal solid waste from a mechanical-biological treatment plant.

    Science.gov (United States)

    Álvarez-Gallego, Carlos José; Fdez-Güelfo, Luis Alberto; de los Ángeles Romero Aguilar, María; Romero García, Luis Isidoro

    2015-02-09

    The organic fraction of municipal solid waste (OFMSW) usually contains high lignocellulosic and fatty fractions. These fractions are well-known to be a hard biodegradable substrate for biological treatments and its presence involves limitations on the performance of anaerobic processes. To avoid this, thermochemical pretreatments have been applied on the OFMSW coming from a full-scale mechanical-biological treatment (MBT) plant, in order to pre-hydrolyze the waste and improve the organic matter solubilisation. To study the solubilisation yield, the increments of soluble organic matter have been measured in terms of dissolved organic carbon (DOC), soluble chemical oxygen demand (sCOD), total volatile fatty acids (TVFA) and acidogenic substrate as carbon (ASC). The process variables analyzed were temperature, pressure and NaOH dosage. The levels of work for each variable were three: 160-180-200 °C, 3.5-5.0-6.5 bar and 2-3-4 g NaOH/L. In addition, the pretreatment time was also modified among 15 and 120 min. The best conditions for organic matter solubilisation were 160 °C, 3 g NaOH/L, 6.5 bar and 30 min, with yields in terms of DOC, sCOD, TVFA and ASC of 176%, 123%, 119% and 178% respectively. Thus, predictably the application of this pretreatment in these optimum conditions could improve the H2 production during the subsequent Dark Fermentation process.

  19. Thermochemical Pretreatments of Organic Fraction of Municipal Solid Waste from a Mechanical-Biological Treatment Plant

    Directory of Open Access Journals (Sweden)

    Carlos José Alvarez-Gallego

    2015-02-01

    Full Text Available The organic fraction of municipal solid waste (OFMSW usually contains high lignocellulosic and fatty fractions. These fractions are well-known to be a hard biodegradable substrate for biological treatments and its presence involves limitations on the performance of anaerobic processes. To avoid this, thermochemical pretreatments have been applied on the OFMSW coming from a full-scale mechanical-biological treatment (MBT plant, in order to pre-hydrolyze the waste and improve the organic matter solubilisation. To study the solubilisation yield, the increments of soluble organic matter have been measured in terms of dissolved organic carbon (DOC, soluble chemical oxygen demand (sCOD, total volatile fatty acids (TVFA and acidogenic substrate as carbon (ASC. The process variables analyzed were temperature, pressure and NaOH dosage. The levels of work for each variable were three: 160–180–200 °C, 3.5–5.0–6.5 bar and 2–3–4 g NaOH/L. In addition, the pretreatment time was also modified among 15 and 120 min. The best conditions for organic matter solubilisation were 160 °C, 3 g NaOH/L, 6.5 bar and 30 min, with yields in terms of DOC, sCOD, TVFA and ASC of 176%, 123%, 119% and 178% respectively. Thus, predictably the application of this pretreatment in these optimum conditions could improve the H2 production during the subsequent Dark Fermentation process.

  20. Thermochemical Nonequilibrium 2D Modeling of Nitrogen Inductively Coupled Plasma Flow

    Science.gov (United States)

    Yu, Minghao; Yusuke, Takahashi; Hisashi, Kihara; Ken-ichi, Abe; Kazuhiko, Yamada; Takashi, Abe; Satoshi, Miyatani

    2015-09-01

    Two-dimensional (2D) numerical simulations of thermochemical nonequilibrium inductively coupled plasma (ICP) flows inside a 10-kW inductively coupled plasma wind tunnel (ICPWT) were carried out with nitrogen as the working gas. Compressible axisymmetric Navier-Stokes (N-S) equations coupled with magnetic vector potential equations were solved. A four-temperature model including an improved electron-vibration relaxation time was used to model the internal energy exchange between electron and heavy particles. The third-order accuracy electron transport properties (3rd AETP) were applied to the simulations. A hybrid chemical kinetic model was adopted to model the chemical nonequilibrium process. The flow characteristics such as thermal nonequilibrium, inductive discharge, effects of Lorentz force were made clear through the present study. It was clarified that the thermal nonequilibrium model played an important role in properly predicting the temperature field. The prediction accuracy can be improved by applying the 3rd AETP to the simulation for this ICPWT. supported by Grant-in-Aid for Scientific Research (No. 23560954), sponsored by the Japan Society for the Promotion of Science

  1. Biomass thermochemical conversion. Overview of results; Biomassan jalostus. Tutkimusalueen katsaus

    Energy Technology Data Exchange (ETDEWEB)

    Sipilae, K. [VTT Energy, Jyvaeskylae (Finland)

    1997-12-01

    The BIOENERGY Programme comprised two research institute projects, one enterprise project and two demonstration projects in 1996. The studies focused on the development of flash pyrolysis technology for biomass, and on the study of the storage stability of imported wood oils and of their suitability for use in oil-fired boilers and diesel power plants. Development of biomass gasification/gas engine concepts suitable for diesel power plants was also initiated. In addition to techno-economic assessments, experimental work was carried out focusing on the cleaning of gasification gas for engine use. Conversion of by-products from the pulping industry, in particular crude soap, into liquid fuels was studied by laboratory tests. Results obtained within IEA Bioenergy Agreement are also surveyed and a new three-year work plan is presented in the overview. (orig.)

  2. An Experimental Study to Control Scour at River Confluence

    Science.gov (United States)

    Wuppukondur, A.; Chandra, V.

    2015-12-01

    The aim of present study is finding a method to control sediment erosion at river confluence. The confluences are mixture of two different flows and are common occurrences along the river. River confluences are sites of natural scour phenomenon and also influence reservoir sedimentation. The river confluence is associated with a separation zone, stagnation zone and a mixing layer along which the scour hole is observed. The eroded sediment creates potential problems by depositing at unwanted downstream locations such as barrages, weirs, check dams, reservoirs etc. As per the literature, the storage capacity of major reservoirs in India is going to be reduced nearly half of the storage capacity by 2020. Hence, an experimental study has been conducted on mobile bed (d50=0.28 mm) with a confluence angle of 90o for a discharge ratio (Qr) of 0.5, where, Qr is defined as the ratio between lateral flow discharge (Ql) and main flow discharge (Qm). Circular shape pile models of same diameter are arranged in a systematic manner with constant spacing (5 cm, 10 cm and 15 cm) to change the flow pattern for reducing scour at the confluence. Two types of pile models (8 mm ϕ and 12 mm ϕ) are used to conduct the experiments. The experimental results show that maximum scour depth at confluence is reduced by 60%. In addition, the bed profile modifications are also reported. Keywords: Reservoir sedimentation, River confluence, Mobile bed, Scour, Vanes. References:1. Borghei, S. M., and Sahebari, A. J. (2010). "Local Scour at Open-Channel Junctions", Journal of Hydraulic Research, 48(4), 37 - 41. 2. Kothyari, U. C. (1996). "Methods for Estimation Sediment Yield from Catchments", Proc., Int. Sem. On Civil Engg. Practices in Twenty First Century, Roorkee, India, 1071-1086. 3. Mosley, M. P. (1976) "An Experimental Study of Channel Confluences". The Journal of Geology, 84(55), 532-562. 4. Ouyang, H. T. (2009). "Investigation on the dimensions and shape of a submerged vane for sediment

  3. Geodynamic modelling of low-buoyancy thermo-chemical plumes

    Science.gov (United States)

    Dannberg, Juliane; Sobolev, Stephan

    2015-04-01

    The Earth's biggest magmatic events that form Large Igneous Provinces are believed to originate from massive melting when hot mantle plumes rising from the lowermost mantle reach the base of the lithosphere. Classical models of thermal mantle plumes predict a flattening of the plume head to a disk-like structure, a kilometer-scale surface uplift just before the initiation of LIPs and thin plume tails. However, there are seismic observations and paleo-topography data that are difficult to explain with this classical approach. Here, using numerical models, we show that the issue can be resolved if major mantle plumes are thermo-chemical rather than purely thermal. It has been suggested a long time ago that subducted oceanic crust could be recycled by mantle plumes; and based on geochemical data, they may contain up to 15-20% of this recycled material in the form of dense eclogite, which drastically decreases their buoyancy and makes it depth-dependent. We perform numerical experiments in a 3D spherical shell geometry to investigate the dynamics of the plume ascent, the interaction between plume- and plate-driven flow and the dynamics of melting in a plume head. For this purpose, we use the finite-element code ASPECT, which allows for complex temperature-, pressure- and composition-dependent material properties. Moreover, our models incorporate phase transitions (including melting) with the accompanying rheological and density changes, Clapeyron slopes and latent heat effects for both peridotite and eclogite, mantle compressibility and a strong temperature- and depth-dependent viscosity. We demonstrate that despite their low buoyancy, such plumes can rise through the whole mantle causing only negligible surface uplift. Conditions for this ascent are high plume volume and moderate lower mantle subadiabaticity. While high plume buoyancy results in plumes directly advancing to the base of the lithosphere, plumes with slightly lower buoyancy pond in a depth of 300-400 km

  4. Experimental techniques for deflection and radiation studies with bent crystals

    CERN Document Server

    Hasan, Said

    2011-01-01

    What happens when a high energy charged particle crosses an amorphous material? It loses energy by ionization and its trajectory is affected by the multiple Coulomb scattering, being these phenomena originated by uncorrelated collisions with the atoms. If the atoms of the target were distributed according to an ordered scheme, the uncorrelated collisions would turn into a coherent interaction with the whole atomic structure. This is the case of an aligned crystal that, depending on the orientation, is seen as a set of atomic planes or strings by the impinging particles. Planes and strings produce potential wells able to confine the charged particles in a transversal region of the crystal, in the so called channeling condition, so that, bending the crystal, particles are forced to follow the curvature, being deflected. This simple and powerful idea, dating 1979, is at the basis of many theoretical and experimental studies that have proven bent crystals effectiveness, described their possible applications and ...

  5. A Transmission Electron Microscope Study of Experimentally Shocked Pregraphitic Carbon

    Science.gov (United States)

    Rietmeijer, Frans J. M.

    1995-01-01

    A transmission electron microscope study of experimental shock metamorphism in natural pre-graphitic carbon simulates the response of the most common natural carbons to increased shock pressure. The d-spacings of this carbon are insensitive to the shock pressure and have no apparent diagnostic value, but progressive comminution occurs in response to increased shock pressure up to 59.6 GPa. The function, P = 869.1 x (size(sub minimum )(exp -0.83), describes the relationship between the minimum root-mean-square subgrain size (nm) and shock pressure (GPa). While a subgrain texture of natural pregraphitic carbons carries little information when pre-shock textures are unknown, this texture may go unnoticed as a shock metamorphic feature.

  6. Experimental study of coherent betatron resonances with a Paul trap

    Directory of Open Access Journals (Sweden)

    S. Ohtsubo

    2010-04-01

    Full Text Available Linear and nonlinear resonant instabilities of charged-particle beams traveling in periodic quadrupole focusing channels are studied experimentally with a compact non-neutral plasma trap. The present experiments are based on the idea that the collective motion of a beam in an accelerator is physically similar to that of a one-component plasma in a trap. A linear Paul trap system named “S-POD” (simulator for particle orbit dynamics was developed to explore a variety of space-charge-induced phenomena. To emulate lattice-dependent effects, periodic perturbations are applied to quadrupole electrodes, which gives rise to additional resonance stop bands that shift depending on the plasma density. It is confirmed that an mth-order resonance takes place when the corresponding tune of an mth-order collective mode Ω_{m} is close to a half integer.

  7. Modular hybrid total hip arthroplasty. Experimental study in dogs

    Directory of Open Access Journals (Sweden)

    Ranzani José JT

    2011-07-01

    Full Text Available Abstract Background This prospective experimental study evaluated the surgical procedure and results of modular hybrid total hip arthroplasty in dogs. Methods Ten skeletally mature healthy mongrel dogs with weights varying between 19 and 27 kg were used. Cemented modular femoral stems and uncemented porous-coated acetabular cups were employed. Clinical and radiographic evaluations were performed before surgery and at 30, 60, 90, 120, 180 and 360 days post-operation. Results Excellent weight bearing was noticed in the operated limb in seven dogs. Dislocation followed by loosening of the prosthesis was noticed in two dogs, which were therefore properly treated with a femoral head osteotomy. Femoral fracture occurred in one dog, which was promptly treated with full implant removal and femoral osteosynthesis. Conclusions The canine modular hybrid total hip arthroplasty provided excellent functionality of the operated limb.

  8. An experimental study of rotor-filter pump performance

    Energy Technology Data Exchange (ETDEWEB)

    Marshek, K.M.; Naja, M.R.

    1982-09-01

    The performance of a rotor-filter pump has been studied experimentally. To develop an understanding of pump performance, and in particular to discern the mechanism of hydraulic pulsing, flow visualization in the rotor, vibration analyses of the pump, frequency analysis of the pump hydraulic pressure pulsation, and analyses of flow characteristics for different pick-up tubes in combination with different impellers and cover plates were conducted. The frequencies of the pump's hydraulic pulsation is shown to be a function of the number of pick-up arms and the motor speed. The pump vibration and its pulsation amplitude were reduced by increasing the number of pick-up arms or by adding a radial impeller. These actions increased the lowest frequency of pulsation and decreased the chance of excitation of the pump system parts.

  9. Numerical and Experimental Study of Friction Loss in Hydrostatic Motor

    DEFF Research Database (Denmark)

    Sørensen, Rasmus Mørk; Hansen, Michael R.; Mouritsen, Ole Ø.

    2012-01-01

    This paper presents a numerical and experimental study of the losses in a hydrostatic motor principle. The motor is designed so that the structural de ections and lubricating regimes between moving surfaces and, subsequently, the leakage and friction losses, can be controlled during operation....... This is done by means of additional pressure volumes that in uence the stator de ection. These pressures are referred to as compensation pressures and the main emphasis is on friction or torque loss modeling of the motor as a function of the compensation pressures and the high and low pressures related...... to the load torque. The torque loss modeling is identied as a Stribeck curve which depends on gap height. The asperity friction is decreasing exponentially with an increase in gap height. The parameters of the torque loss model are based on prototype measurements that include the structural de ections...

  10. Experimental study of equilibrium in a bumpy torus

    Energy Technology Data Exchange (ETDEWEB)

    Hiroe, S.; Cobble, J.A.; Colchin, R.J.; Chen, G.L.; Connor, K.A.; Goyer, J.R.; Solensten, L.

    1986-06-01

    Plasma equilibrium in the ELMO Bumpy Torus (EBT) was studied experimentally by measurements of the electrostatic potential structure. Before an electron tail population is formed, the electric field is found, roughly speaking, to be in the vertical direction. The appearance of a high-energy electron tail signals the formation of a negative potential well, and the potential contours start to nest. The potential contours are shifted inward with respect to the center of the conducting wall. The electric field between the plasma and the conducting wall forces the plasma inward, balancing the outward expansion force. This force balance provides a horizontal electric field that cancels the concentric radial electric field locally at the separatrix of the potential contour and leads to convective energy loss.

  11. Experimental study of a rotating packed bed distillation column

    Directory of Open Access Journals (Sweden)

    J. V. S. Nascimento

    2009-03-01

    Full Text Available The purpose of this work was to study the mass transfer performance of rotating packed beds applying the "Higee" process. The operations were carried out with the n-hexane/n-heptane distilling system at atmospheric pressure and under total reflux conditions. The rotating speed could be varied between 300 and 2500 rpm, which provided centrifugal forces from 5 to 316 times the Earth's gravity. The effects of concentration, vapor velocity, rotating speed and packing type (two different Raschig ring sizes and structured wire mesh packing on mass transfer behavior were analyzed. Experimental results showed that the mass transfer coefficient depends on the liquid flow rates and rotating speed. The equipment had high separation efficiency in a reduced bed volume.

  12. Numerical and Experimental Study of Pump Sump Flows

    Directory of Open Access Journals (Sweden)

    Wei-Liang Chuang

    2014-01-01

    Full Text Available The present study analyzes pump sump flows with various discharges and gate submergence. Investigations using a three-dimensional large eddy simulation model and an acoustic Doppler velocimeter are performed. Flow patterns and velocity profiles in the approaching flow are shown to describe the flow features caused by various discharges and gate submergence. The variation of a large-scale spanwise vortex behind a sluice gate is examined and discussed. The suction effect on approaching flow near the pipe column is examined using numerical modeling. To gain more understanding of the vortices variation, a comparison between time-averaged and instantaneous flow patterns is numerically conducted. Additionally, swirl angle, a widely used index for evaluating pump efficiency, is experimentally and numerically examined under various flow conditions. The results indicate that the pump becomes less efficient with increasing discharge and gate submergence. The fluctuation of the free surface over the pump sump is also discussed.

  13. Experimental Study of a 45-MHz Array for Radio Astronomy

    Science.gov (United States)

    Alvarez, H.; Aparici, J.; May, J.; Olmos, F.

    1994-09-01

    The University of Chile transit radiotelescope is a 528-dipole array operating at 45 MHz. We present a comparison of an experimental study of the antenna radiation pattern with the basic theoretical pattern in three dimensions. We concentrate in the meridian plane diagram since this is particularly difficult to measure for an array like ours. The comparison shows excellent agreement. We have measured several important antenna parameters like the effective area as a function of zenith distance, the orientation of the plane of the array and the pointing accuracy. We include a detailed treatment of these subjects since not much information related to low frequency arrays for radio astronomy can be found in the literature. We discuss the importance of knowing these parameters in the preparation of the 45-MHz Sky Survey under way at the University of Chile Radio Observatory.

  14. Numerical simulation and experimental study of explosive projectile devices

    Science.gov (United States)

    Selivanov, V. V.; Gryaznov, E. F.; Goldenko, N. A.; Sudomoev, A. D.; Feldstein, V. A.

    2017-06-01

    A study of explosive-throwing device (ETD) was undertaken to simulate the hypervelocity impact of space debris fragments (SDF) and meteoroids with spacecrafts. The principle of operation of an ETD is based on the cumulative effect in combination with the cut-off head of the cumulative jet, which enables one to simulate a compact particle, such as a meteoroid or a fragment of space debris. Different design schemes of ETD with different composition explosive charge initiation schemes with notably low speeds of the jet cut-off are explored, and a method to control the particle velocity is proposed. Numerical simulation of device modes and basic technical characteristics of experimental testing are investigated.

  15. Experimental and simulated study of a composite structure metamaterial absorber

    Science.gov (United States)

    Li, Shengyong; Ai, Xiaochuan; Wu, Ronghua; Chen, Jiajun

    2017-11-01

    In this paper, a high performance metamaterial absorber is designed and experimental studied. Measured results indicate that a perfect absorption band and a short-wavelength absorption peak are achieved in the near-infrared spectrum. Current strength distributions reveal that the absorption band is excited by the cavity resonance. And electric field distributions show that the short-wavelength absorption peak is excited by the horizontal coupled of localized surface plasmon (LSP) modes near hole edges. On the one hand, the absorption property of the measured metamaterial absorber can be enhanced through optimizing the structural parameters (a, w, and H). On the other hand, the absorption property is sensitive to the change of refractive index of environmental medias. A sensing scheme is proposed for refractive index detecting based on the figure of merit (FOM) value. Measured results indicate that the proposed sensing scheme can achieve high FOM value with different environmental medias (water, glucose solution).

  16. An experimental and modeling study of n-octanol combustion

    KAUST Repository

    Cai, Liming

    2015-01-01

    This study presents the first investigation on the combustion chemistry of n-octanol, a long chain alcohol. Ignition delay times were determined experimentally in a high-pressure shock tube, and stable species concentration profiles were obtained in a jet stirred reactor for a range of initial conditions. A detailed kinetic model was developed to describe the oxidation of n-octanol at both low and high temperatures, and the model shows good agreement with the present dataset. The fuel\\'s combustion characteristics are compared to those of n-alkanes and to short chain alcohols to illustrate the effects of the hydroxyl moiety and the carbon chain length on important combustion properties. Finally, the results are discussed in detail. © 2014 The Combustion Institute.

  17. Experimental study of infrared filaments under different initial conditions

    Science.gov (United States)

    Mirell, Daniel Joseph

    In 1964, four years after the first working laser was constructed, long skinny damage tracks and fluorescence trails were seen inside of certain transparent media that were excited by intense light pulses [1]. What was so remarkable about these features was the narrowness of the spatial profile and their long propagation length in the beam in concert with the very high intensity of the light that would be necessary to produce them. A purely linear model of light propagation through such media was insufficient to explain the results of these experiments and hence a new area of nonlinear optics, latex coined filamentation (to describe the length, slimness, and intensity of the light field), was born. Filament studies begin with a medium that has a nonlinear index of refraction, n¯2, that interacts with an intense beam of light so as to cause it to self-focus. The n¯2 of liquid and solid transparent media is much higher than the n¯ 2 of gases and therefore a much higher intensity of laser source would need to be invented to begin the study of filaments in air. With the advent of the Ti-Sapphire Kerr-lens modelocked laser [2], working in combination with the development of the chirped pulse amplifier system in the mid-1990's, light intensities sufficient to produce filaments in air was realized. Since that time much experimental and theoretical work has been done to better understand some of the additional complexities that arise specifically in the filamentation of light in air using several different wavelengths (UV to IR) and pulsewidths (femto- to pico-seconds). Many theoretical models exist each with a different emphasis on the various physical mechanisms that may produce the features experimentally observed in filaments. The experimental work has sought to give the theoretician better data on some of the properties of filaments such as the: (a) spatial and temporal structure of the beam and of the produced plasma (that arises due to the high intensity light

  18. Experimental study of drag reduction in flumes and spillway tunnels

    Directory of Open Access Journals (Sweden)

    Ying-kui Wang

    2010-06-01

    Full Text Available Experiments in an open flume model and spillway tunnel model were carried out using drag reduction techniques. Two drag reduction techniques were adopted in the experiments: polymer addition and coating. The drag reduction effect of a polyacrylamide (PAM solution and dimethyl silicone oil coating were studied in the flume model experiments, and the results were analyzed. Experiments were then carried out with a model of the Xiluodu Hydropower Station, the second largest dam in China. In order to reduce the resistance, the spillway tunnels were internally coated with dimethyl silicone oil. This is the first time that these drag reduction techniques have been applied to so large a hydraulic model. The experimental results show that the coating technique can effectively increase flood discharge. The outlet velocity and the jet trajectory distance are also increased, which enhances the energy dissipation of the spillway tunnel.

  19. An experimental study on improvement of Savonius rotor performance

    Directory of Open Access Journals (Sweden)

    N.H. Mahmoud

    2012-03-01

    In this work different geometries of Savonius wind turbine are experimentally studied in order to determine the most effective operation parameters. It was found that, the two blades rotor is more efficient than three and four ones. The rotor with end plates gives higher efficiency than those of without end plates. Double stage rotors have higher performance compared to single stage rotors. The rotors without overlap ratio (β are better in operation than those with overlap. The results show also that the power coefficient increases with rising the aspect ratio (α. The conclusions from the measurements of the static torque for each rotor at different wind speeds verify the above summarized results of this work.

  20. Perceptions of unfairness in price increases: an experimental study

    Directory of Open Access Journals (Sweden)

    Verônica Feder Mayer

    2014-09-01

    Full Text Available This experimental study investigates antecedents and consequences of perceptions of price unfairness in a price increase situation. The proposed theoretical model states that consumer dependence on the service provider as well as the relevance the consumer attributes to the service (for the consumer's life will affect his/her degree of (a unfairness price perception, (b anger, and (c intention to complain and retaliate. The results support all the hypotheses specified in the model. The findings not only indicate that some situations of unfairness price perception lead to stronger emotions and more dramatic reactions from consumers, but also allow us to predict which situations of perceived unfairness offer greater risks and have greater potential for conflict.

  1. The role of bibliotherapy in health anxiety: an experimental study.

    Science.gov (United States)

    Jones, Freda A

    2002-10-01

    Despite its high prevalence and implications for health care resources, health anxiety is generally considered difficult and expensive to manage. Structured self-help materials (bibliotherapy) using a cognitive behaviour therapy (CBT) treatment approach have been shown to be clinically effective. This experimental study investigated the effects of bibliotherapy on patients who had been identified as demonstrating health concerns. The 40 participants (patients drawn from GP surgeries) were randomly allocated to two groups, one receiving bibliotherapy and the other not. Half the patients had a medically diagnosed problem. Anxiety was assessed before and after the bibliotherapy intervention, which took the form of a cognitive-behavioural self-help booklet for health anxiety sufferers. Patients in the bibliotherapy group showed reduced levels of anxiety at post-test, even when they also had an identifiable physical problem. These results are consistent with the idea that self-help materials can be an effective and accessible intervention in CBT, although further research is recommended.

  2. Simulation and experimental study of resin flow in fibre fabrics

    Science.gov (United States)

    Yan, Fei; Yan, Shilin; Li, Yongjing

    2017-06-01

    Liquid Composite Moulding (LCM) is gradually becoming the most competitive manufacturing technology for producing large composite parts with complex geometry with high quality and low cost. These parts include those for airplanes, wind turbine blades and automobile components. Fibre fabrics in liquid composite moulding can be considered as dual-scale porous media. In different gap scales, an unsaturated flow is produced during the mould filling process. This particular flow behaviour deviates from the traditional Darcy’s law, which is used to calculate the filling pressure and will cause errors. According to sink theory, the unsaturated flow characteristics of this dual-scale porous media were studied in this paper, and a FEM solution program was developed. The results showed that the pressure curves against the position which simulated by sink functions were departure from the position of traditional theory. In addition, the simulation results of partially-saturated region were consistent with the experimental data.

  3. An experimental study on particle effects in liquid sheets

    Directory of Open Access Journals (Sweden)

    Sauret Alban

    2017-01-01

    Full Text Available Many industrial processes, such as surface coating or liquid transport in tubes, involve liquid sheets or thin films of suspensions. In these situations, the thickness of the liquid film becomes comparable to the particle size, which leads to unexpected dynamics. In addition, the classical constitutive rheological law for suspensions cannot be applied as the continuum approximation is no longer valid. Here, we consider experimentally a transient particle-laden liquid sheet that expands radially. We characterize the influence of the particles on the shape of the liquid film and the atomization process. We highlight that the presence of particles modifies the thickness and stability of the liquid sheet. Our study suggests that the influence of particles through capillary effects can modify significantly the dynamics of processes that involve suspensions and particles confined in liquid films.

  4. Theoretical and experimental study of 15N NMR protonation shifts.

    Science.gov (United States)

    Semenov, Valentin A; Samultsev, Dmitry O; Krivdin, Leonid B

    2015-06-01

    A combined theoretical and experimental study revealed that the nature of the upfield (shielding) protonation effect in 15N NMR originates in the change of the contribution of the sp(2)-hybridized nitrogen lone pair on protonation resulting in a marked shielding of nitrogen of about 100 ppm. On the contrary, for amine-type nitrogen, protonation of the nitrogen lone pair results in the deshielding protonation effect of about 25 ppm, so that the total deshielding protonation effect of about 10 ppm is due to the interplay of the contributions of adjacent natural bond orbitals. A versatile computational scheme for the calculation of 15N NMR chemical shifts of protonated nitrogen species and their neutral precursors is proposed at the density functional theory level taking into account solvent effects within the supermolecule solvation model. Copyright © 2015 John Wiley & Sons, Ltd.

  5. Experimental study on silicon micro-heat pipe arrays

    Energy Technology Data Exchange (ETDEWEB)

    Launay, S.; Sartre, V.; Lallemand, M. [Institut National des Sciences Appliquees, Villeurbanne (France). Centre de Thermique

    2004-02-01

    In this study, micro-heat pipe arrays etched into silicon wafers have been investigated for electronic cooling purposes. Micro-heat pipes of triangular cross-section and with liquid arteries were fabricated by wet anisotropic etching with a KOH solution. The microchannels (230 {mu}m wide) are closed by molecular bonding of a plain wafer with the grooved one. A test bench was developed for the micro-heat pipe filling and the thermal characterisation. The temperature profile on the silicon surface is deduced from experimental measurements. The results show that with the artery micro-heat pipe array, filled with methanol, the effective thermal conductivity of the silicon wafer is significantly improved compared to massive silicon. (author)

  6. [Pathomorphological studies of experimental thiazole-80 poisoning in sheep].

    Science.gov (United States)

    Petkov, P

    1979-01-01

    Investigations on the pathomorphological changes occurring in the organisms of 4 sheep poisoned experimentally by varying Thiazole-80 doses applied orally were made. It was established macroscopically that after opening the rumen a smell of sulfuric hydrogen is felt. The abomasum was with rusty brown haemorrhages and liver distrophy as well as enlarged gall bladder were observed. The histological studies of parenchymal organs revealed vascular disturbances, hyperemia, oedema and intervascular haemolysis. A heavy diffuse nephrosis, hyaline and protein cylinders were found in the kidney cortex, while in the ganglial cells of medula oblongata were evident degenerative changes. Histochemically, in sheep poisoned by thiazole-80, a well expressed reaction to iron in the lungs, leptomeniges and distrophic hepatocytes were established. Glycogen quantity in the liver was considerably reduced.

  7. BIOLOGICAL EFFECTS OF PULSED SHORT WAVE TREATMENT. AN EXPERIMENTAL STUDY

    Directory of Open Access Journals (Sweden)

    Dogaru Gabriela

    2015-02-01

    Full Text Available Pulsed short waves are short electromagnetic waves emitted as intermittent trains with a fixed duration, separated by free intervals of variable duration. The biological effects of pulsed short waves could be explained according to most of the authors by an activation of cellular enzymatic reactions, a stimulation of energy metabolism, a stimulation of liver function, of adrenal gland function and of the reticulocyte system, changes in cell permeability, by an increase of peripheral blood flow through the enhancement of local vascularization. This research aimed to investigate the biological effects of exposure to pulsed short waves at different doses on the adrenal glands of experimental animals, by structural and ultrastructural studies. The study included 35 animals assigned to 4 groups. Group I included 10 experimental animals exposed to radiation at a dose of 1/80 impulses/sec, group II, 10 animals exposed to a dose of 4/400 impulses/sec, group III, 10 animals exposed to a dose of 6/600 impulses/sec, for 10 min/day, and the control group consisted of 5 unexposed animals. Structural and ultrastructural changes of adrenal glands induced by the dose of 4/400 impulses/sec, compared to the unexposed control group and the dose of 1/80 impulses/sec, include an intensification of protein synthesis processes, an enhancement of energy metabolism in providing the energy required for an increased production of hormones, an intensification of collagen fiber synthesis processes in the capsule, necessary for healing. It was demonstrated that this dose induced an intensification of hormone synthesis and secretion, a stimulation of adrenal function. At the dose of 6/600 cycles/sec, a slight diminution of hormone synthesis and secretion activity was found, which was not below the limits existing in the unexposed control group, but was comparable to group II. This dose is probably too strong for experimental animals, inducing them a state of stress. The

  8. Experimental plan for the Single-Family Study

    Energy Technology Data Exchange (ETDEWEB)

    Berry, L.G.; Brown, M.A.; Wright, T.; White, D.L.

    1991-09-01

    The national evaluation of the Weatherization Assistance Program (WAP) consists of five separate studies. The Single-Family Study is one of three studies that will estimate program energy savings and cost effectiveness in principal WAP submarkets. This report presents the experimental plan for the Single-Family Study, which will be implemented over the next three years (1991--1993). The Single-Family Study will directly estimate energy savings for a nationally representative sample of single-family and small multifamily homes weatherized in the 1989 program year. Savings will be estimated from gas and electric utility billing records using the Princeton Scorekeeping Method (PRISM). The study will also assess nonenergy impacts (e.g., health, comfort, safety, and housing affordability), estimate cost effectiveness, and analyze factors influencing these outcomes. For homes using fuels such as wood, coal, fuel oil, kerosene, and propane as the primary source of space conditioning, energy savings will be studied indirectly. The study will assemble a large nationally representative data base. A cluster sampling approach will be used, in which about 400 subgrantees are selected in a first stage and weatherized homes are selected in a second range. To ensure that the Single-Family Study is able to identify promising opportunities for future program development, two purposively selected groups of subgrantees will be included: (1) subgrantees that install cooling measures (such as more efficient air conditioning equipment or radiant barriers), and (2) exemplary subgrantees that use state-of-the-art technologies and service delivery procedures (such as advanced audit techniques, blower door tests, infrared scanners, extensive client education, etc.). These two groups of subgrantees will be analyzed to identify the most effective program elements in specific circumstances. 14 refs., 4 figs., 3 tabs.

  9. Biomass-powered Solid Oxide Fuel Cells : Experimental and Modeling Studies for System Integrations

    NARCIS (Netherlands)

    Liu, M.

    2013-01-01

    Biomass is a sustainable energy source which, through thermo-chemical processes of biomass gasification, is able to be converted from a solid biomass fuel into a gas mixture, known as syngas or biosyngas. A solid oxide fuel cell (SOFC) is a power generation device that directly converts the chemical

  10. Experimental studies and modeling on concentration polarization in forward osmosis.

    Science.gov (United States)

    Qin, Jian-Jun; Chen, Sijie; Oo, Maung Htun; Kekre, Kiran A; Cornelissen, Emile R; Ruiken, Chris J

    2010-01-01

    Concentration polarization (CP) is an important issue in forward osmosis (FO) processes and it is believed that the coupled effect of dilutive internal CP (DICP) and concentrative external CP (CECP) limits FO flux. The objective of this study was to distinguish individual contribution of different types of DICP and CECP via modeling and to validate it by pilot studies. The influence of DICP/CECP on FO flux has been investigated in this study. The CP model presented in this work was derived from a previous study and evaluated by bench-scale FO experiments. Experiments were conducted with drinking water as the feed and NaCl/MgSO(4) as draw solutions at different concentrations and velocities. Modeling results indicated that DICP contributed to a flux reduction by 99.9% for 0.5 M NaCl as a draw solution although the flow pattern of both feed and draw solutions was turbulent. DICP could be improved via selection of the draw solution. The modeling results were well fit with the experimental data. It was concluded that the model could be used for selection of the draw solution and prediction of water flux under similar situation. A draw solution with greater diffusion coefficient or a thinner substrate of an asymmetric FO membrane resulted in a higher flux.

  11. A Novel Approach to Experimental Studies of Mineral Dissolution Kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Chen Zhu; William E. Seyfried

    2005-01-01

    Currently, DOE is conducting pilot CO{sub 2} injection tests to evaluate the concept of geological sequestration. One strategy that potentially enhances CO{sub 2} solubility and reduces the risk of CO{sub 2} leak back to the surface is dissolution of indigenous minerals in the geological formation and precipitation of secondary carbonate phases, which increases the brine pH and immobilizes CO{sub 2}. Clearly, the rates at which these dissolution and precipitation reactions occur directly determine the efficiency of this strategy. However, one of the fundamental problems in modern geochemistry is the persistent two to five orders of magnitude discrepancy between laboratory-measured and field derived feldspar dissolution rates. To date, there is no real guidance as to how to predict silicate reaction rates for use in quantitative models. Current models for assessment of geological carbon sequestration have generally opted to use laboratory rates, in spite of the dearth of such data for compositionally complex systems, and the persistent disconnect between lab and field applications. Therefore, a firm scientific basis for predicting silicate reaction kinetics in CO{sub 2} injected geological formations is urgently needed to assure the reliability of the geochemical models used for the assessments of carbon sequestration strategies. The funded experimental and theoretical study attempts to resolve this outstanding scientific issue by novel experimental design and theoretical interpretation to measure silicate dissolution rates and iron carbonate precipitation rates at conditions pertinent to geological carbon sequestration. In the first year of the project, we have successfully developed a sample preparation method and completed three batch feldspar dissolution experiments at 200 C and 300 bars. The changes of solution chemistry as dissolution experiments progressed were monitored with on-line sampling of the aqueous phase at the constant temperature and pressure

  12. Experimental studies of light emission phenomena in superconducting RF cavities

    Energy Technology Data Exchange (ETDEWEB)

    Anthony, P.L. [SLAC National Accelerator Laboratory, Menlo Park, CA 94025 (United States); Delayen, J.R. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport, News, VA 23606 (United States); Center for Accelerator Science, Old Dominion University, Norfolk, VA, 23529 (United States); Fryberger, D., E-mail: fryberger@slac.stanford.ed [SLAC National Accelerator Laboratory, Menlo Park, CA 94025 (United States); Goree, W.S. [2G Enterprises, Pacific Grove, CA 93950 (United States); Mammosser, J. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport, News, VA 23606 (United States); Szalata, Z.M.; Weisend, J.G. [SLAC National Accelerator Laboratory, Menlo Park, CA 94025 (United States)

    2009-12-21

    Experimental studies of light emission phenomena in superconducting RF cavities, which we categorize under the general heading of cavity lights, are described. The cavity lights data, which were obtained using a small CCD video camera, were collected in a series of nine experimental runs ranging from approx1/2 to approx2 h in duration. The video data were recorded on a standard VHS tape. As the runs progressed, additional instrumentation was added. For the last three runs a LabVIEW-controlled data acquisition system was included. These runs furnish evidence for several, possibly related, light emission phenomena. The most intriguing of these is what appear to be small luminous objects <=1.5 mm in size, freely moving about in the vacuum space, generally without wall contact, as verified by reflections of the tracks in the cavity walls. In addition, on a number of occasions, these objects were observed to bounce off of the cavity walls. The wall-bounce aspect of most of these events was clearly confirmed by pre-bounce and post-bounce reflections concurrent with the tracks. In one of the later runs, a mode of behavior was observed that was qualitatively different from anything observed in the earlier runs. Perhaps the most perplexing aspect of this new mode was the observation of as many as seven luminous objects arrayed in what might be described as a macromolecular formation, coherently moving about in the interior of the cavity for extended periods of time, evidently without any wall contact. It is suggested that these mobile luminous objects are without explanation within the realm of established physics. Some remarks about more exotic theoretical possibilities are made, and future plans are discussed.

  13. Overview: Experimental studies of crystal nucleation: Metals and colloids

    Science.gov (United States)

    Herlach, Dieter M.; Palberg, Thomas; Klassen, Ina; Klein, Stefan; Kobold, Raphael

    2016-12-01

    Crystallization is one of the most important phase transformations of first order. In the case of metals and alloys, the liquid phase is the parent phase of materials production. The conditions of the crystallization process control the as-solidified material in its chemical and physical properties. Nucleation initiates the crystallization of a liquid. It selects the crystallographic phase, stable or meta-stable. Its detailed knowledge is therefore mandatory for the design of materials. We present techniques of containerless processing for nucleation studies of metals and alloys. Experimental results demonstrate the power of these methods not only for crystal nucleation of stable solids but in particular also for investigations of crystal nucleation of metastable solids at extreme undercooling. This concerns the physical nature of heterogeneous versus homogeneous nucleation and nucleation of phases nucleated under non-equilibrium conditions. The results are analyzed within classical nucleation theory that defines the activation energy of homogeneous nucleation in terms of the interfacial energy and the difference of Gibbs free energies of solid and liquid. The interfacial energy acts as barrier for the nucleation process. Its experimental determination is difficult in the case of metals. In the second part of this work we therefore explore the potential of colloidal suspensions as model systems for the crystallization process. The nucleation process of colloids is observed in situ by optical observation and ultra-small angle X-ray diffraction using high intensity synchrotron radiation. It allows an unambiguous discrimination of homogeneous and heterogeneous nucleation as well as the determination of the interfacial free energy of the solid-liquid interface. Our results are used to construct Turnbull plots of colloids, which are discussed in relation to Turnbull plots of metals and support the hypothesis that colloids are useful model systems to investigate crystal

  14. Experimental Studies of Light Emission Phenomena in Superconducting RF Cavitites

    Energy Technology Data Exchange (ETDEWEB)

    Anthony, P.L.; /SLAC; Delayen, J.R.; /Jefferson Lab; Fryberger, D.; /SLAC; Goree, W.S.; Mammosser, J.; /Jefferson Lab /SNS Project, Oak Ridge; Szalata, Z.M.; II, J.G.Weisend /SLAC

    2009-08-04

    Experimental studies of light emission phenomena in superconducting RF cavities, which we categorize under the general heading of cavity lights, are described. The cavity lights data, which were obtained using a small CCD video camera, were collected in a series of nine experimental runs ranging from {approx} 1/2 to {approx} 2 h in duration. The video data were recorded on a standard VHS tape. As the runs progressed, additional instrumentation was added. For the last three runs a LabVIEW controlled data acquisition system was included. These runs furnish evidence for several, possibly related, light emission phenomena. The most intriguing of these is what appear to be small luminous objects {le} 1.5 mm in size, freely moving about in the vacuum space, generally without wall contact, as verified by reflections of the tracks in the cavity walls. In addition, on a number of occasions, these objects were observed to bounce off of the cavity walls. The wall-bounce aspect of most of these events was clearly confirmed by pre-bounce and post-bounce reflections concurrent with the tracks. In one of the later runs, a mode of behavior was observed that was qualitatively different from anything observed in the earlier runs. Perhaps the most perplexing aspect of this new mode was the observation of as many as seven luminous objects arrayed in what might be described as a macromolecular formation, coherently moving about in the interior of the cavity for extended periods of time, evidently without any wall contact. It is suggested that these mobile luminous objects are without explanation within the realm of established physics. Some remarks about more exotic theoretical possibilities are made, and future plans are discussed.

  15. Experimental study of vortex breakdown in a cylindrical, swirling flow

    Science.gov (United States)

    Stevens, J. L.; Celik, Z. Z.; Cantwell, B. J.; Lopez, J. M.

    1996-01-01

    The stability of a steady, vortical flow in a cylindrical container with one rotating endwall has been experimentally examined to gain insight into the process of vortex breakdowwn. The dynamics of the flow are governed by the Reynolds number (Re) and the aspect ratio of the cylinder. Re is given by Omega R(sup 2)/nu, where Omega is the speed of rotation of the endwall, R is the cylinder radius, and nu is the kinematic viscosity of the fluid filling the cylinder. The aspect ratio is H/R, where H is the height of the cylinder. Numerical simulation studies disagree whether or not the steady breakdown is stable beyond a critical Reynolds number, Re(sub c). Previous experimental researches have considered the steady and unsteady flows near Re(sub c), but have not explored the stability of the steady breakdown structures beyond this value. In this investigation, laser induced fluorescence was utilized to observe both steady and unsteady vortex breakdown at a fixed H/R of 2.5 with Re varying around Re(sub c). When the Re of a steady flow was slowly increased beyond Re(sub c), the breakdown structure remained steady even though unsteadiness was possible. In addition, a number of hysteresis events involving the oscillation periods of the unsteady flow were noted. The results show that both steady and unsteady vortex breakdown occur for a limited range of Re above Re(sub c). Also, with increasing Re, complex flow transformations take place that alter the period at which the unsteady flow oscillates.

  16. Epidural blood patch: A study on an experimental model

    Directory of Open Access Journals (Sweden)

    S K Sengupta

    2013-01-01

    Full Text Available Aim: Epidural blood patch has been used to treat spinal headache with varying success. An experimental model was designed to ascertain whether an epidural blood patch can be used to seal the needle puncture sites in dural repair. Materials and Methods: Bovine dura was secured to the lower end of an open-ended calibrated plastic cylinder. Multiple interrupted stitches were applied over a 02 cm length of the dura without any incision. The cylinder was filled with colored saline gradually with the dura placed in a dependent position. Height of the water column at which sutured dura leaked was recorded. A layer of fresh blood was laid over the dura and allowed to clot. The test was repeated and the hydrostatic pressure at which leak took place was noted again. The test was repeated three times. Similar studies were done with two specimens with 02-cm dural incisions repaired with interrupted stitches of 4-0 silk in one specimen and 4-0 prolene in another, and three specimens with 3-mm unsutured dural rent in one and dural punctures made with 23-G and 26-G spinal needles in the other two. Results: All the dural preparations leaked, at a very low hydrostatic pressure (<30 mm of H 2 O. By covering the needle puncture sites with clotted blood, a watertight closure could be achieved, that can withstand a much higher hydrostatic pressure (mean of 180 mm of H 2 O. Conclusion : The experimental findings indicate that an epidural blood patch does enhance the ability of a dural closure to prevent a leak; however, its utility in clinical setting is questionable.

  17. Experimental study of a single channel alluvial fan

    Science.gov (United States)

    Delorme, Pauline; Devauchelle, Olivier; Barrier, Laurie; Métivier, François

    2016-04-01

    At the outlet of mountain ranges, rivers reach a flat plain and start to depose their sediment load into a conical sedimentary structure called alluvial fan. To decipher these sedimentary records, we need to understand the dynamics of their growth. Most natural fans are built by braided streams. However, to avoid the complexity of braided rivers, we develop a small-scale experiment in which an alluvial fan is formed by a single channel. We use a mixture of water and glycerol to produce a laminar river. The fluid is mixed with corindon sand (~ 300 μm) in a tilted channel and left free to form a fan around its outlet. The sediment and water discharges are constant during an experimental run. We record the fan progradation and the channel morphology with top-view pictures. We also generate an elevation map with an optical method based on the deformation of a moiré pattern. We observe that, to leading order, the fan remains self-affine as it grows, with a constant slope. We compare two recent studies about the formation of one-dimensionnal fan [Guerit et al. 2014] and threshold rivers [Seizilles et al. 2013] to our experimental findings. In particular, we propose a theory witch relates the fan morphology to the control parameters (fluid and sediment discharges, grain size). Our observations accord with the predictions, suggesting that the fan is built near the threshold of sediment motion. At the first order, the fan profile is linear and control by the water discharge. The downstream decrease in sediment discharge add a curvature to this profile. Finally, we intend to expand our interpretation to alluvial fans build by single-thread channels ( Okavango, Bostwana; Taquari and Paraguay, Brasil).

  18. Thermochemical analysis and kinetics aspects for a chemical model for camphene ozonolysis.

    Science.gov (United States)

    Oliveira, R C de M; Bauerfeldt, G F

    2012-10-07

    In this work, a chemical model for the camphene ozonolysis, leading to carbonyl final products, is proposed and discussed on the basis of the thermochemical properties and kinetic data obtained at density functional theory levels of calculation. The mechanism is initiated by the electrophilic attack of ozone to the double bond in camphene leading to a 1,2,3-trioxolane intermediate, which decomposes to peroxy radicals and carbonyl compounds in a total of 10 elementary reactions. The thermodynamic properties (enthalpy and entropies differences) are calculated at 298 K. For the thermochemical evaluation, theoretical calculations are performed with the B3LYP, MPW1PW91, and mPW1K density functionals and the basis sets 6-31G(d), 6-31G(2d,2p), 6-31+G(d,p), and 6-31+G(2d,2p). Eventually, single point calculations adopting the 6-311++G(2d,2p) basis set are performed in order to improve the electronic energies. The enthalpy profiles suggest highly exothermic reactions for the individual steps, with a global enthalpy difference of -179.18 kcal mol(-1), determined at the B3LYP∕6-31+G(2d,2p) level. The Gibbs free energy differences for each step, at 298 K, calculated at the B3LYP∕6-311++G(2d,2p)∕∕B3LYP∕6-31+G(2d,2p) level, are used to estimate the composition of a final product mixture under equilibrium conditions as 58% of camphenilone and 42% of 6,6-dimethyl-ɛ-caprolactone-2,5-methylene. For the reaction kinetics, the bimolecular O(3) + camphene step is assumed to be rate determining in the global mechanism. A saddle point for the ozone addition to the double bond is located and rate constants are determined on the basis of the transition state theory. This saddle point is well represented by a loosely bound structure and corrections for the basis set superposition error (BSSE) are calculated, either by considering the effect over the geometry optimization procedure (here referred as CP1 procedure), or the effect of the BSSE over the electronic energy of a

  19. Proteomic Studies on Human and Experimental Cerebral Malaria

    KAUST Repository

    Moussa, Ehab

    2012-07-01

    Cerebral malaria (CM) is a severe neurological complication of malaria infection that results from interrelated pathologies. Despite extensive research efforts, the mechanism of the disease is not completely understood. Clinical studies, postmortem analysis, and animal models have been the main research arenas in CM. In this thesis, shotgun proteomics approach was used to further understand the pathology of human and experimental CM. The mechanism by which CM turns fatal is yet to be identified. A clinical proteomics study was conducted on pooled plasma samples from children with reversible or fatal CM from the Gambia. The results show that depletion of coagulation factors and increased levels of circulating proteasomes are associated with fatal pediatric CM. This data suggests that the ongoing coagulation during CM might be a disseminated intravascular coagulation state that eventually causes depletion of the coagulation factors leading to petechial hemorrhages. In addition, the mechanism(s) by which blood transfusion benefits CM in children was investigated. To that end, the concentration and multimerization pattern of von-willebrand factor, and the concentration of haptoglobin in the plasma of children with CM who received blood transfusions were measured. In addition to clinical studies, experimental cerebral malaria (ECM) in mice has been long used as a model for the disease. A shotgun proteomics workflow was optimized to identify the proteomic signature of the brain tissue of mice with ECM.Because of the utmost importance of membrane proteins in the pathology of the disease, sample fractionation and filter aided sample preparation were used to recover them. The proteomic signature of the brains of mice infected with P. berghei ANKA that developed neurological syndrome, mice infected with P. berghei NK56 that developed severe malaria but without neurological signs, and non-infected mice, were compared to identify CM specific proteins. Among the differentially

  20. [Crystalline lens photodisruption using femtosecond laser: experimental study].

    Science.gov (United States)

    Chatoux, O; Touboul, D; Buestel, C; Balcou, P; Colin, J

    2010-09-01

    The aim of this study was to analyze the interactions during femtosecond (fs) laser photodisruption in ex vivo porcine crystalline lenses and to study the parameters for laser interaction optimization. An experimental femtosecond laser was used. The laser characteristics were: 1030 nm wavelength; pulse duration, 400 fs; and numerical aperture, 0.13. Specific software was created to custom and monitor any type of photoablation pattern for treatment purposes. Porcine crystalline lenses were placed in an open sky holder filled with physiological liquid (BSS) covered by a glass plate. A numerical camera was associated with metrological software in order to magnify and quantify the results. Transmission electron microscopy (TEM) was performed on some samples to identify the microscopic plasma interactions with the lens. The optimization of parameters was investigated in terms of the optical breakdown threshold, the sizing of interactions, and the best pattern for alignments. More than 150 crystalline lenses of freshly enucleated pigs were treated. The optical breakdown threshold (OBT) was defined as the minimal energy level per pulse necessary to observe a physical interaction. In our study, the OBT varied according to the following parameters: the crystalline lens itself, varying from 4.2 to 7.6 μJ (mean, 5.1 μJ), and the depth of laser focus, varying up to 1 μJ, increasing in the depth of the tissue. Analyzing the distance between impacts, we observed that the closer the impacts were the less power was needed to create a clear well-drawn defect pattern (lines), i.e., with a 4-μJ optimized OBT, when the impacts were placed every 2 μm for the x,y directions and 60 μm for the z direction. Coalescent bubbles created by plasma formation always disappeared in less than 24h. The nonthermal effect of plasma and the innocuousness on surrounding tissues were proven by the TEM results. The crystalline lens photodisruption by the femtosecond laser seems an innovative

  1. Experimental study on mechanical properties of aircraft honeycomb sandwich structures

    Directory of Open Access Journals (Sweden)

    Talebi Mazraehshahi H.

    2010-06-01

    Full Text Available Mechanical behaviour of sandwich panels under different conditions have been exprimentally studied in this research to increase the knowledge of aircraft sandwich panel structures and facilitate design criteria for aircraft structures. Tests were concentrated on the honeycomb sandwich structures under different loads including flexural, insert shear, flat wise tension and compression loads. Furthermore, effect of core density and face material on mechanical behavior of different samples were investigated and compared with analytical and FEM method. Effects of skin thickness on strength of honycomb sandwhich panels under shear pull out and moments have also been considerd in this study. According to this investigation, insert strength and flexural test under different load conditions is strongly affected by face thickness, but compression and tearoff (falt wise tensile properties of a sandwich panel depends on core material. The study concludes that the correlation between experimental results and the analytical predictions will enable the designer to predict the mechanical behaviour and strength of a sandwich beam; however, applied formula may lead engineers to unreliable results for shear modulus.

  2. Designing Awe in Virtual Reality: An Experimental Study

    Directory of Open Access Journals (Sweden)

    Alice Chirico

    2018-01-01

    Full Text Available Awe is a little-studied emotion with a great transformative potential. Therefore, the interest toward the study of awe’s underlying mechanisms has been increased. Specifically, researchers have been interested in how to reproduce intense feelings of awe within laboratory conditions. It has been proposed that the use of virtual reality (VR could be an effective way to induce awe in controlled experimental settings, thanks to its ability of providing participants with a sense of “presence,” that is, the subjective feeling of being displaced in another physical or imaginary place. However, the potential of VR as awe-inducing medium has not been fully tested yet. In the present study, we provided an evidence-based design and a validation of four immersive virtual environments (VEs involving 36 participants in a within-subject design. Of these, three VEs were designed to induce awe, whereas the fourth VE was targeted as an emotionally neutral stimulus. Participants self-reported the extent to which they felt awe, general affect and sense of presence related to each environment. As expected, results showed that awe-VEs could induce significantly higher levels of awe and presence as compared to the neutral VE. Furthermore, these VEs induced significantly more positive than negative affect. These findings supported the potential of immersive VR for inducing awe and provide useful indications for the design of awe-inspiring virtual environments.

  3. Theoretical and experimental study of fiber-optic fluorescence immunosensors

    Science.gov (United States)

    Cao, He

    This dissertation investigates the optical detection of antigens (in this case, food pathogens such as Salmonella) with fiber-optic immunosensors. The major techniques used for this optical detection include: (1)Linking the antigens to some physical tracers that can be optically detected; (2)Collecting and transmitting the optical signal to an optical detector. From an optical point of view, the problem is a nonimaging-optics problem to collect a fluorescent signal from an extended Lambertian source and deliver it to an optical detection system with maximum energy transfer and distinct wavelength separation. A raytrace model of the optical detection system was used for numerical simulations to analyze and optimize the optical design. The result leads to an improvement of the optical detection. Related physical problems such as magnetic focusing effect, fluorescence detection, and wavelength separation have also been studied in detail. With the adoption of a single-step immunomagnetic assay, experimental studies have been conducted for the detection of Salmonella, with a dual- fiber optical probe and tapered tubular waveguide probes. The test results have shown that the detection system gives detection limit of approximately 106 CFU/ml with dual-fiber optical probes, and 105 CFU/ml with improved tubular waveguide probes. The system developed for this research project is designed as a cost-effective portable instrument that may be used for field-testing. Rapid and on-site detection, low cost instrumentation and a reusable optical probe have been emphasized throughout the study.

  4. Studies on experimental models used for nutritional and biological ...

    African Journals Online (AJOL)

    The anatomical location for a successful implantation in order to reduce complications to the hearest minimum has been suggested . The maintenance of the implanted cannulae for the purpose of keeping the modified experimental model in perfect health is discussed. Key Words: Experimental Models, Nutritional Biological ...

  5. An Experimental Study on Wall Thickness Distribution in Thermoforming

    Directory of Open Access Journals (Sweden)

    Sencer Süreyya Karabeyoglu

    2017-09-01

    Full Text Available In this work, Polystyrene (PS sheets were thermoformed in predetermined conditions. Wall thickness distributions obtained by experimental method in PS thermoformed products. Then same thickness distributions were predicted by using Geometric Element Analysis (GEA. The thickness results which obtained experimentally, compared to thickness distributions which were predicted by GEA. It has been found that GEA does not reveal thickness distributions precisely.

  6. A "self adhering" prosthesis for hernia repair: experimental study.

    Science.gov (United States)

    Champault, G; Polliand, C; Dufour, F; Ziol, M; Behr, L

    2009-02-01

    Prosthetic reinforcement is now routine in the management of inguinal and incisional hernia, and it significantly reduces the risk of recurrence. After surgery, chronic pain is often attributed to the characteristics of the mesh and to the method of fixation in the wound, with a potential risk of nerve or muscle injuries. To evaluate the properties of a new "self adhering" prosthesis in an experimental animal study. The self adhering prosthesis, a lightweight (40 mg/m(2)) polypropylene mesh coated with a synthetic glue on one side, was implanted laparoscopically in pigs. Removal of the prosthesis was performed at one day, one week and one month post operatively. A macroscopic and microscopic evaluation was performed. The results, using a quantitative score, were compared to those of a control group using the same polypropylene mesh without glue, but fixed by staples. The operative time was significantly lower in the self adhering group: 23 min (15-32) versus 31 min (21-40) (P = 0.01). The average time interval from the introduction of the mesh into the preperitoneal space until the appearance of the first tough adhesion was 3 min (2-4). In the control group, the mesh handling time was 8.3 min (5-14) (P = 0.01). At the time of implantation, the score was at a maximum value in all cases for the self adhering prostheses, especially concerning handling and adhesiveness. Upon removal, this score was noted to be good or very good in 90-100% of the cases. There was a good integration in the muscle confirmed histologically, and there was no shrinkage, no mobilisation and no migration. At one month, the thickness of the fibrosis at the limits of the meshes was significantly higher for the self adhering prostheses (P = 0.02). In this experimental study, the self adhering prosthesis demonstrated its adhesive properties and its ability to be well tolerated, with a good macroscopic and microscopic integration into the abdominal wound. This should allow us to perform a clinical

  7. Experimental and theoretical study of delayed ettringite damage in concrete

    Science.gov (United States)

    Ramadan, Elsaid Osman

    2000-12-01

    An experimental study is conducted to investigate the effect of a range of parameters on concrete expansion and premature deterioration associated with delayed ettringite formation (DEF). These parameters were identified from a comprehensive literature review; they include concrete curing conditions and cement chemistry. Specifically, the study investigated the effect of potassium and magnesium contents as well as the effect of water and steam curing conditions on concrete damage associated with DEF. An accelerated test method for DEF was evaluated and modifications are suggested. Concrete specimens were prepared with varying amounts of potassium and magnesium and subjected to different curing conditions. To accelerate any potential expansion, a beat cycle was employed. The change in length of the specimens was monitored for the duration of the study. Specimens were analyzed using the scanning electron microscope, x-ray dispersive analysis, and x-ray diffraction to determine the mechanism responsible for deterioration. Computed tomography x-ray was also employed as a non-destructive method for examining the internal crack patterns associated with expansion. The expansion data is fitted using the Kohnogorov-Avrami-Johenson-Mehl (KAJM) equation. This theory makes it possible to identify individual expansion processes and to identify the contribution of different expansion mechanisms. All concretes showed expansion following the beat cycle. Subjecting concrete to the heat cycle has a primary role in accelerating expansion. The age at which concrete is subjected to the beat cycle as well as the sample dimensions have a profound effect on the resulting expansion. The use of the concrete prisms as suggested in the modified test method offers a better alternative to cores suggested by Duggan. Increasing the potassium content has a deleterious effect on concrete expansion and premature deterioration and is also associated with dramatic reduction in compressive strength

  8. Thermochemical stability and friction properties of soft organosilica networks for solid lubrication

    NARCIS (Netherlands)

    Gonzalez Rodriguez, P.; Dral, A. Petra; van den Nieuwenhuijzen, Karin J.H.; Lette, Walter; Schipper, Dik J.; ten Elshof, Johan E.

    2018-01-01

    In view of their possible application as high temperature solid lubricants, the tribological and thermochemical properties of several organosilica networks were investigated over a range of temperatures between 25 and 580 °C. Organosilica networks, obtained from monomers with terminal and bridging

  9. Thermochemical hydrogen production via a cycle using barium and sulfur - Reaction between barium sulfide and water

    Science.gov (United States)

    Ota, K.; Conger, W. L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653-866 C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. An expression was derived for the rate of hydrogen formation.

  10. Low-buoyancy thermochemical plumes resolve controversy of classical mantle plume concept

    National Research Council Canada - National Science Library

    Dannberg, Juliane; Sobolev, Stephan V

    2015-01-01

    .... We demonstrate that, despite their low buoyancy, large enough thermochemical plumes can rise through the whole mantle causing only negligible surface uplift. Their tails are bulky (>200 km radius) and remain in the upper mantle for 100 millions of years....

  11. Evaluation energy efficiency of bioconversion knot rejects to ethanol in comparison to other thermochemically pretreated biomass

    Science.gov (United States)

    Zhaojiang Wang; Menghua Qin; J.Y. Zhu; Guoyu Tian; Zongquan. Li

    2013-01-01

    Rejects from sulfite pulp mill that otherwise would be disposed of by incineration were converted to ethanol by a combined physical–biological process that was comprised of physical refining and simultaneous saccharification and fermentation (SSF). The energy efficiency was evaluated with comparison to thermochemically pretreated biomass, such as those pretreated by...

  12. A review on the properties of salt hydrates for thermochemical storage

    NARCIS (Netherlands)

    Trausel, F.; Jong, A.J. de; Cuypers, R.

    2014-01-01

    Solar energy is capable of supplying enough energy to answer the total demand of energy in dwellings. However, because of the discrepancy between energy supply and energy demand, an efficient way of storing thermal energy is crucial. Thermochemical storage of heat in salt hydrates provides an

  13. Characterization of Thermochemically Surface-Hardened Titanium by Light Optical Microscopy

    DEFF Research Database (Denmark)

    Gammeltoft-Hansen, Niklas; Munch, Steffen S.; Jellesen, Morten Stendahl

    2017-01-01

    Thermochemically treated titanium grades 2 and 5 were investigated by light optical microscopy and hardness indentation. Gaseous oxidation in oxygen and N2O containing atmospheres resulted in a diffusion zone of oxygen in solid solution in titanium with a hardness up to 1000 HV. A surface scale...

  14. Theoretical and Experimental Study of Bimetal-Pipe Hydroforming.

    Science.gov (United States)

    Dezhi, Zeng; Kuanhai, Deng; Taihe, Shi; Yuanhua, Lin; Hongjun, Zhu; Tianlei, Li; Yongxing, Sun

    2014-12-01

    The corrosion of oil country tubular goods (OCTG) gets more and more serious especially in the acidic environment. So, it is very important to develop a perfect anticorrosion technology for exploring sour oil and gas fields economically and safely. Analysis indicates that the bimetal-pipe (BP) which consists of the base layer of low carbon steel and a corrosion resistant alloy (CRA) cladding layer is an economic and reliable anticorrosion technology and has broad application prospects in the transportation of acid medium. However, theoretical study of hydraulic expansion mechanism for BP is not enough. In this paper, the deformation compatibility condition of BP was obtained by studying the deformation rule of the (CRA) liner and the outer pipe of carbon steel in the forming process; the mechanical model which can compute the hydroforming pressure of BP has been established based on the nonlinear kinematic hardening characteristics of material; furthermore, based on the stress strain curve of inner pipe simultaneously, the calculation method of the plastic hardening stress has been proposed. Thus, the accurate method for computing the forming pressure was obtained. The experimental data show that results are consistent with results of the proposed model. It indicates that the model can be used to provide theoretical guidance for the design and production as well as use of BP.

  15. Laser Experimental Study of the Surface Vibrations of EMUS Sensor

    Science.gov (United States)

    Wilkie-Chancellier, N.; Wang, Y.; Martinez, L.; Roucaries, B.; Serfaty, S.

    In order to ensure a comprehensive monitoring of the material structuration in liquid phase, the traditional ultrasonic techniques require excitation in contact which is often inadequate for online tracking. To monitor the material evolution remotely, a new electromagnetic ultrasonic sensor (EMUS) was successfully developed in our laboratory. The EMUS transducer is based on a resonant thickness shear mode sensor (TSM) magnetically coupled to a high frequency antenna. The TSM resonator consists in a piezoelectric AT-cut quartz plate with metal electrodes on opposite sides. The application of a radio frequency electrical signal gives rise to the excitation of a shear mechanical resonance. The work presented here allows characterizing the acoustic behavior of the EMUS. A laser vibrometer is used to scan the surface of the TSM resonator and visualize the propagation of the generated surface waves. This study shows a good agreement between experimental and theoretical results which encourages the study of acoustic interaction between the TSM resonator and a material in contact with the quartz surface. They therefore suggest that this non-destructive technique can be used to extract the viscoelastic properties of materials.

  16. A Perspective on the Experimental Techniques for Studying Lamins

    Directory of Open Access Journals (Sweden)

    Ilaria Pecorari

    2017-10-01

    Full Text Available Lamins are type V intermediate filaments that collectively form a meshwork underneath the inner nuclear membrane, called nuclear lamina. Furthermore, they are also present in the nucleoplasm. Lamins are experiencing a growing interest, since a wide range of diseases are induced by mutations in the gene coding for A-type lamins, globally known as laminopathies. Moreover, it has been demonstrated that lamins are involved in other pathological conditions, like cancer. The role of lamins has been studied from several perspectives, exploiting different techniques and procedures. This multidisciplinary approach has contributed to resolving the unique features of lamins and has provided a thorough insight in their role in living organisms. Yet, there are still many unanswered questions, which constantly generate research in the field. The present work is aimed to review some interesting experimental techniques performed so far to study lamins. Scientists can take advantage of this collection for their novel investigations, being aware of the already pursued and consolidated methodologies. Hopefully, advances in these research directions will provide insights to achieve better diagnostic procedures and effective therapeutic options.

  17. [Muscular control of scapholunate instability. An experimental study].

    Science.gov (United States)

    León-López, M M; García-Elías, M; Salvà-Coll, G; Llusá-Perez, M; Lluch-Bergadà, A

    2014-01-01

    As long as the neuromuscular stabilizers are intact, a lesion of the scapholunate ligament may or may not progress to a carpal instability. The mechanisms by which the muscles compensate this defect are not very well known. We designed an experimental study with the aim of clarifying these mechanisms. Using 10 fresh wrists, with no pre-existing lesions, we studied the movements of the scaphoid, triquetrum and capitate produced by the isometrical loading of the muscles which move the wrist, each of them isolated or combined, before and after cutting off the scapholunate ligaments. To do this, we placed sensors in each of these bones and used the Fastrack system to record these movements. The simultaneous loading of the muscles of the wrist produce rotational movements in flexion and supination of the proximal carpal row. After cutting off the scapholunate ligaments, the scaphoid rotates in pronation and flexion, while the triquetrum rotates in pronation and extension. In this situation of a scapholunate lesion, the muscles that worsen the carpal dexasation are the extensor carpi ulnaris and flexor carpi ulnaris. On the other hand, the isolated loading of the radial muscles reduce the scapholunate diastasis, thus improving the carpal alignment. In dynamic scapholunate instabilities, isometric contraction of the ulnar carpal muscles must be avoided, as it promotes the scapholunate diastasis. The rest of the muscles have the opposite effect, stabilizing the carpus when primary stabilizers have failed. Copyright © 2013 SECOT. Published by Elsevier Espana. All rights reserved.

  18. A retrievable nitinol endobronchial stent : an experimental study in dog

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Sang Jin; Park, Sang Soo; Yoon, Hyun Ki; Sung, Kyu Bo; Song, Ho Young [Asan Medical Center, Ulsan Univ. College of Medicine, Seoul (Korea, Republic of); Kang, Sung Gwon [Inha Univ. College of Medicine, Inchon (Korea, Republic of)

    1999-06-01

    The purpose of this study was to evaluate the safety and the retrievability of a new covered retrievable nitinol tracheobronchial stent. Stents were knitted from 0.2mm nitinol wire, covered with polyurethane, and were 20-22mm in diameter and 2cm in length. Under fluoroscopic guidance, a stent was placed in the normal right bronchus intermedius of ten dogs. Using a retrieval hook, stent retrieval was attempted after 1 month(N=5) or 2 months(N=5). After removal, the dogs were sacrificed and their their tracheobronchial trees were examined grossly and histologically. Eleven stents were successfully placed in ten dogs. Migration and expectoration occurred in four of ten stents in nine dogs(40%). Five stents were successfully removed from six dogs(83%). Without significant difference between the two groups, mild to moderate mucosal hyperplasia was noted at the sites of stents as well as above and below them. On microscopy, three of five dogs showed pneumonia in the right middle lobes, but none of the stents was covered with epithelium. Temporary placement of a covered expandable nitinol stent in the tracheobronchial tree is feasible, but to establish its efficacy, further experimental studies are needed.

  19. Cold-formed steel pallet rack connection: an experimental study

    Science.gov (United States)

    Mohan, Vimal; Prabha, P.; Rajasankar, J.; Iyer, Nagesh R.; Raviswaran, N.; Nagendiran, V.; Kamalakannan, S. S.

    2015-03-01

    Industrial pallet rack systems are made up of three-dimensional structural arrangement using cold-formed steel members. The rack columns (upright) have perforations at prescribed intervals to facilitate the assemblage of beams with end connections. The tabs are used as connections which are engaged into the perforations and are in particular, highly semi-rigid in nature. Due to the diversity of rack systems, connecting member's stiffness and strength, it is almost impossible to develop a generalised model for analytical predication of the connection stiffness. This paper describes the beam-column connection tests carried out on a commercially available pallet rack system by adopting single cantilever test set-up. Thirty-five sets of combinations are identified based on the variation in upright profile and thickness, depth of beam and the connector to study the connection stiffness. Three tests were performed for each set to bring in uniformity in the result taking the total number of tests to 105. A full range parametric study is carried out to understand the influence of above said parameters on moment-rotation behaviour and the joint stiffness. The experimental results showed that an improved performance of the joint connection is achieved using connectors with more number of tabs, greater thickness and improved profile of the upright and larger depth of the beam.

  20. Nab: precise experimental study of unpolarized neutron beta decay

    Science.gov (United States)

    Pocanic, Dinko; Nab Collaboration

    2014-09-01

    Nab, a program of experimental study of unpolarized neutron decays at the Spallation Neutron Source, Oak Ridge, TN, aims to determine a, the electron-neutrino correlation with precision of δa / a =10-3 , and b, the Fierz interference term, with uncertainty δb ~= 3 ×10-3 . Neutron beta decay's simple theoretical description in the Standard Model (SM) is overconstrained by the set of available observables, providing opportunities to search for evidence of SM extensions. Planned Nab results will lead to a new precise determination of the ratio λ =GA /GV , and to significant reductions in the allowed limits for both right- and left-handed scalar and tensor currents. Alternatively, the experiment may detect a discrepancy from SM predictions consistent with certain realizations of supersymmetry. An optimized, asymmetric spectrometer has been designed to achieve the narrow proton momentum response function required to meet the physics goals of the experiment. The apparatus is to be used in a follow-up measurement (ABba) of asymmetry observables A and B in polarized neutron decay. Nab is funded, now in the construction stage, with planned beam readiness in 2016. We discuss the experiment's motivation, expected reach, design and method. Nab, a program of experimental study of unpolarized neutron decays at the Spallation Neutron Source, Oak Ridge, TN, aims to determine a, the electron-neutrino correlation with precision of δa / a =10-3 , and b, the Fierz interference term, with uncertainty δb ~= 3 ×10-3 . Neutron beta decay's simple theoretical description in the Standard Model (SM) is overconstrained by the set of available observables, providing opportunities to search for evidence of SM extensions. Planned Nab results will lead to a new precise determination of the ratio λ =GA /GV , and to significant reductions in the allowed limits for both right- and left-handed scalar and tensor currents. Alternatively, the experiment may detect a discrepancy from SM

  1. Experimental and numeric study of aluminum wire explosion in vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Tkachenko, S.I.; Khattatov, T.A.; Tilikin, I.N. [MIPT, Dolgoprudny, Moscow Region (Russian Federation); Romanova, V.M.; Mingaleev, A.R.; Ter-Oganesyan, A.E.; Shelkovenko, T.A.; Pikuz, S.A. [P.N. Lebedev Physical Institute RAS, Moscow (Russian Federation); Olhovskaya, O.G.; Krukovskij, A.Y.; Gasilov, V.A.; Novikov, V.G. [IMM RAS, Moscow (Russian Federation)

    2011-07-01

    Full text of publication follows: Distribution of matter in the discharge channel formed upon a nanosecond electrical explosion of Al wire in vacuum was studied experimentally and theoretically. Several series of experiments with 25 {mu}m diameter 12 mm long wires were performed; the charging voltage, the current amplitude and current rise rate were U{sub 0} = 20 kV, Imax {approx} 10 kA and dI/dt = 50 A/ns, respectively [1]. 'Shadow and Schlieren' images of the discharge channel were obtained using optical probing at the second harmonic of a YAG: Nd{sup +3} laser ({lambda} = 0.532 {mu}m, {tau} {approx} 70 ps). Simultaneous use of optical and UV diagnostics made it possible to distinguish qualitatively different regions of the discharge channel, such as the current-carrying plasma layers and the region occupied by a weakly conducting cold matter. The simulations were performed using a program containing the Braginsky two temperature magnetic gas-dynamic model: Lagrange-Euler code RAZRYAD-2.5 [2] on the basis of homogeneous, conservative and implicit differences of MHD schemes. Radiation energy exchange is accounted for in a multi-group (from the spectrum) approximation, using a radiation diffusion model. Heat- and electro- conductivity anisotropy in magnetic field is taken into account. Tables of thermal-physical and optical properties of aluminum were used in calculations in the present work [3]. The influence of radiation on the distribution of the parameters of matter (temperature, density) and current density in the discharge channel was studied. Several variants with differing amounts of radiation of spectral groups were evaluated. The obtained results are compared with experimental data. This work was supported in part by the RFBR 08-08-00688, 09-02-01532, and the ESC FIAN.; [1]. S.I. Tkachenko et. al., Plasma Physics Reports, 2009, Vol. 35, No. 9, pp. 734-753; [2]. V.A. Gasilov et. al., Mathematical Modelling, 2003, v. 15, No 9, pp. 107-124; [3]. A

  2. Numerical and experimental studies of droplet-gas flow

    Energy Technology Data Exchange (ETDEWEB)

    Joesang, Aage Ingebret

    2002-07-01

    This thesis considers droplet-gas flow by the use of numerical methods and experimental verification. A commercial vane separator was studied both numerical and by experiment. In addition some efforts are put into the numerical analysis of cyclones. The experimental part contains detailed measurements of the flow field between a pair of vanes in a vane separator and droplet size measurements. LDA (Laser Doppler Anemometry) was used to measure the velocity in two dimensions and corresponding turbulence quantities. The results from the LDA measurements are considered to be of high quality and are compared to numerical results obtained from a CFD (Computational Fluid Dynamics) analysis. The simulation showed good agreement between the numerical and experimental results. Combinations of different turbulence models; the standard k-epsilon model and the Reynold Stress Mode, different schemes; first order and higher order scheme and different near wall treatment of the turbulence; the Law of the wall and the Two-Layer Zonal model were used in the simulations. The Reynold Stress Model together with a higher order scheme performed rather poorly. The recirculation in parts of the separator was overpredicted in this case. For the other cases the overall predictions are satisfactory. PDA (Phase Doppler Anemometry) measurements were used to study the changes in the droplet size distribution through the vane separator. The PDA measurements show that smaller droplets are found at the outlet than present at the inlet. In the literature there exists different mechanisms for explaining the re-entrainment and generation of new droplets. The re-entrainments mechanisms are divided into four groups where droplet-droplet interaction, droplet break-up, splashing of impinging droplet and re-entrainment from the film are defined as the groups of re-entrainment mechanisms. Models for these groups are found in the literature and these models are tested for re-entrainment using the operational

  3. 2D Numerical Modelling of the Resin Injection Pultrusion Process Including Experimental Resin Kinetics and Temperature Validation

    DEFF Research Database (Denmark)

    Rasmussen, Filip Salling; Sonne, Mads Rostgaard; Larsen, Martin

    2017-01-01

    In the present study, a two-dimensional (2D) transient Eulerian thermo-chemical analysis of a carbon fibre epoxy thermosetting Resin Injection Pultrusion (RIP) process is carried out. The numerical model is implemented using the well known unconditionally stable Alternating Direction Implicit (ADI......) scheme. The total heat of reaction and the cure kinetics of the epoxy thermosetting are determined using Differential Scanning Calorimetry (DSC). A very good agreement is observed between the fitted cure kinetic model and the experimental measurements. The numerical steady state temperature predictions...

  4. On the role of delocalization in benzene: Theoretical and experimental investigation of the effects of strained ring fusion

    Energy Technology Data Exchange (ETDEWEB)

    Faust, Rudiger [Univ. of California, Berkeley, CA (United States)

    1993-04-01

    When an important compound`s discovery dates back as far as 1825, one would imagine that every facet of its chemical and physical properties has been illuminated in the meantime. Benzene, however, has not ceased to challenge the chemist`s notion of structure and bonding since its first isolation by Michael Faraday. This report is divided into the following six chapters: 1. Aromaticity -- Criteria, manifestations, structural limitations; 2. The role of delocalization in benzene; 3. The thermochemical properties of benzocyclobutadienologs; 4. Ab initio study of benzenes fused to four-membered rings; 5. Non-planar polycyclic aromatic hydrocarbons; and 6. Experimental details and input decks. 210 Refs.

  5. Temperature-Dependent Effects of FeS2 Thin Film Synthesized by Thermochemical Spraying: An Optical and Physicochemical Investigation

    Science.gov (United States)

    Kao, Chia-Tze; Shi, Jen-Bin; Lee, Hsuan-Wei; Cheng, Fu-Chou; Liu, Hung-Hsin; Lee, Ming-Way; Chan, Chih-Chieh; Huang, Chien-Wei; Lin, Hsien-Sheng; Wu, Po-Feng; Chen, Chin-Yi; Kao, Ming-Cheng; Young, San-Lin; Lin, Cheng-Li

    2016-02-01

    FeS2 pyrite films are used in a variety of applications including solar cells and, the potential scope for their utilization is increasing as their synthetic methods become more economical while maintaining or enhancing their high light absorption coefficients. The glass substrate temperature dependence on the formation of FeS2 pyrite films was investigated with respect to their optical and physicochemical properties. During the thermochemical spraying process the temperature was varied in the range of 190-290 °C. FeS2 nanocrystalline (40-70 nm) films, formed as a result of atmospheric spraying with glass substrate temperatures above 260 °C, were observed by SEM. Opto-electronic studies revealed that the nanocrystalline films had a direct band gap (1.3-1.6 eV) with a high light absorption coefficient (α > 7 × 104 cm-1 for λ application as high light-absorbing solar energy absorbers.

  6. Significance of vapor phase chemical reactions on CVD rates predicted by chemically frozen and local thermochemical equilibrium boundary layer theories

    Science.gov (United States)

    Gokoglu, Suleyman A.

    1988-01-01

    This paper investigates the role played by vapor-phase chemical reactions on CVD rates by comparing the results of two extreme theories developed to predict CVD mass transport rates in the absence of interfacial kinetic barrier: one based on chemically frozen boundary layer and the other based on local thermochemical equilibrium. Both theories consider laminar convective-diffusion boundary layers at high Reynolds numbers and include thermal (Soret) diffusion and variable property effects. As an example, Na2SO4 deposition was studied. It was found that gas phase reactions have no important role on Na2SO4 deposition rates and on the predictions of the theories. The implications of the predictions of the two theories to other CVD systems are discussed.

  7. Sustaining a Global Social Network: a quasi-experimental study.

    Science.gov (United States)

    Benton, D C; Ferguson, S L

    2017-03-01

    To examine the longer term impact on the social network of participating nurses in the Global Nursing Leadership Institute (GNLI2013) through using differing frequencies of follow-up to assess impact on maintenance of network cohesion. Social network analysis is increasingly been used by nurse researchers, however, studies tend to use single point-in-time descriptive methods. This study utilizes a repeated measures, block group, control-intervention, quasi-experimental design. Twenty-eight nurse leaders, competitively selected through a double-blind peer review process, were allocated to five action learning-based learning groups. Network architecture, measures of cohesion and node degree frequency were all used to assess programme impact. The programme initiated and sustained connections between nurse leaders drawn from a geographically dispersed heterogeneous group. Modest inputs of two to three e-mails over a 6-month period seem sufficient to maintain connectivity as indicated by measures of network density, diameter and path length. Due to the teaching methodology used, the study sample was relatively small and the follow-up data collection took place after a relatively short time. Replication and further cohort data collection would be advantageous. In an era where many policy solutions are being debated and initiated at the global level, action learning leadership development that utilizes new technology follow-up appears to show significant impact and is worthy of wider application. The approach warrants further inquiry and testing as to its longer term effects on nursing's influence on policy formulation and implementation. © 2016 International Council of Nurses.

  8. Influence of Radial Stress Gradient on Strainbursts: An Experimental Study

    Science.gov (United States)

    Su, Guoshao; Zhai, Shaobin; Jiang, Jianqing; Zhang, Gangliang; Yan, Liubin

    2017-10-01

    Strainbursts, which are violent disasters that are accompanied by the ejection failure of rocks, usually occur in hard brittle rocks around highly stressed underground openings. The release of the radial stress at excavation boundaries is one of the major inducing factors for strainbursts in tunnels. After excavation, the radial stress usually exhibits different but apparent gradient variations along the radial direction near the boundary within a certain depth under different in situ stress conditions. In this study, the influence of the radial stress gradient on strainbursts of granite was investigated using an improved true-triaxial rockburst testing system, which was equipped with an acoustic emission monitoring system. The stress state and boundary conditions (i.e., one face free, other faces loaded and increasing tangential stress) of the representative rock element in the vicinity of the excavation boundary were simulated. High-speed cameras were used to capture the ejection failure processes during strainbursts, and the kinetic energy of ejected fragments was quantitatively estimated by analyzing the recorded videos. The experimental results indicate that with an increasing radial stress gradient, the strength increases, the apparent yield platform prior to the peak stress on the stress-strain curves decreases, the failure mode changes from strainburst characterized by tensile splitting to strainburst characterized by shear rupture, and the kinetic energy of ejected fragments during strainbursts significantly increases.

  9. Experimental Liquefaction Study of Southern Yogyakarta Using Shaking Table

    Directory of Open Access Journals (Sweden)

    Lindung Zalbuin Mase

    2017-04-01

    Full Text Available An experimental study using shaking table was conducted to learn liquefaction. Samples used were sandy soils from South of Yogyakarta Special Region Province. Analysis of liquefaction potential was performed by considering several factors, i.e. peak ground acceleration (PGA of 0.3 g to 0.4 g, vibrational frequency of 1.8 Hz, and vibration duration of 8, 16, and 32 seconds which reflect earthquake magnitudes of 5, 6, and 7. The pore water pressure was measured by using a pressure transducer. Liquefaction potential was determined by using the parameter of excess pore water pressure ratio (ru. Liquefaction potentially occurred when ru > 1, whereas ru < 1 indicated liquefaction didn’t occur. The results of test showed that liquefaction potentially occur in each applied dynamic load, that maximum excess pore wate pressure (ru max measured was equal to or larger than 1. The larger peak ground acceleration applied, the faster beginning time of liquefaction. The bigger peak ground acceleration applied, the slower dissipation time of pore water pressure. The duration of liquefaction become longer, along with the increase of applied peak ground acceleration. The bigger applied peak ground acceleration, the larger maximum excess pore water pressure.

  10. Experimental Study of Fast Neutron Irradiation on Si Transistor

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Sung Ho; Sun, Gwang Min; Baek, Ha ni; Jin, Seong Bok; Hoang, Sy Minh Tuan [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Bipolar junction transistors (BJTs) are applied in many industrial fields. BJT is a three-terminal device with an important feature in that the current through two terminals can be controlled by small changes we make in the current or voltage at the third terminal. This control feature allows us to amplify small AC signals or to switch the device from an on state and off state and back. These two operations, amplification and switching, are the basis of a host of electronic functions. This study will investigate the electrical characteristics of a p-n-p BJT, such as the base current and collector current for fast neutron irradiation. Fast neutron irradiation can cause displacement damage in the Si bulk. In this paper, the electrical characteristics of a p-n-p BJT such as a base current and collector current are investigated for fast neutron irradiation. The experimental results show that the base current is increased and the collector current is decreased after fast neutron irradiation. These results indicate that the displacement damage caused by fast neutron irradiation increases the recombination rate of minority carriers and resistors.

  11. Experimental study of two-phase natural circulation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Lemos, Wanderley Freitas; Su, Jian, E-mail: wlemos@lasme.coppe.ufrj.br, E-mail: sujian@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Faccini, Jose Luiz Horacio, E-mail: faccini@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), RIo de Janeiro, RJ (Brazil). Lab. de Termo-Hidraulica Experimental

    2012-07-01

    This paper reports an experimental study on the behavior of fluid flow in natural circulation under single-and two-phase flow conditions. The natural circulation circuit was designed based on concepts of similarity and scale in proportion to the actual operating conditions of a nuclear reactor. This test equipment has similar performance to the passive system for removal of residual heat presents in Advanced Pressurized Water Reactors (A PWR). The experiment was carried out by supplying water to primary and secondary circuits, as well as electrical power resistors installed inside the heater. Power controller has available to adjust the values for supply of electrical power resistors, in order to simulate conditions of decay of power from the nuclear reactor in steady state. Data acquisition system allows the measurement and control of the temperature at different points by means of thermocouples installed at several points along the circuit. The behavior of the phenomenon of natural circulation was monitored by a software with graphical interface, showing the evolution of temperature measurement points and the results stored in digital format spreadsheets. Besides, the natural circulation flow rate was measured by a flowmeter installed on the hot leg. A flow visualization technique was used the for identifying vertical flow regimes of two-phase natural circulation. Finally, the Reynolds Number was calculated for the establishment of a friction factor correlation dependent on the scale geometrical length, height and diameter of the pipe. (author)

  12. A molecular machine biosensor: construction, predictive models and experimental studies.

    Science.gov (United States)

    Moradi-Monfared, Sahar; Krishnamurthy, Vikram; Cornell, Bruce

    2012-04-15

    This paper describes the construction, operation and predictive modeling of a molecular machine, functioning as a high sensitivity biosensor. Embedded gramicidin A (gA) ionchannels in a self-assembled tethered lipid bilayer act as biological switches in response to target molecules and provide a signal amplification mechanism that results in high sensitivity molecular detection. The biosensor can be used as a rapid and sensitive point of care diagnostic device in different media such as human serum, plasma and whole blood without the need for pre and post processing steps required in an enzyme-linked immunosorbent assay. The electrical reader of the device provides the added advantage of objective measurement. Novel ideas in the construction of the molecular machine, including fabrication of biochip arrays, and experimental studies of its ability to detect analyte molecules over a wide range of concentrations are presented. Remarkably, despite the complexity of the device, it is shown that the response can be predicted by modeling the analyte fluid flow and surface chemical reactions. The derived predictive models for the sensing dynamics also facilitate determining important variables in the design of a molecular machine such as the ion channel lifetime and diffusion dynamics within the bilayer lipid membrane as well as the bio-molecular interaction rate constants. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Experimental study on behavior of steel channel strengthened with CFRP

    Directory of Open Access Journals (Sweden)

    Tang Hongyuan

    2017-11-01

    Full Text Available This paper describes the behaviour of axially loaded long and eccentrically loaded short thin-walled steel channels, strengthened with transversely bonded carbon fibre reinforced polymer (CFRP sheets. Seven long members, each 1400 mm long, and seven short members, each 750mmlong, were tested. The main parameters were the number of CFRP plies (one or two and the clear spacing between the CFRP strips (50, 100 or 150 mm. The effect of CFRP sheet layer and clear spacing was studied. All the ultimate load capacity of the reinforced members was improved in different extent. A maximum strength gain of 9.13% was achieved for long members with two CFRP layers and 50 mm spacing of CFRP strips. The experimental results show that the global buckling happens to all the long specimens. For short members, the maximum strength gain of 12.1% was achieved with two CFRP layers and 50 mm spacing of CFRP strips. With the exception of the most heavily reinforced (2 plies at 50 and 100 mm, local buckling was observed prior to global buckling for short members, which was completely opposite of the control specimens. Meanwhile, when the clear spacing of CFRP strips is greater than theweb height of steel channel, the transversely bonded CFRP does not have a significant improvement in buckling load capacity of the short- and long-channel components. While the clear spacing is less than the web height, the more number of CFRP layer, the more enhancement of buckling load capacity.

  14. Augmented reality in bone tumour resection: An experimental study.

    Science.gov (United States)

    Cho, H S; Park, Y K; Gupta, S; Yoon, C; Han, I; Kim, H-S; Choi, H; Hong, J

    2017-03-01

    We evaluated the accuracy of augmented reality (AR)-based navigation assistance through simulation of bone tumours in a pig femur model. We developed an AR-based navigation system for bone tumour resection, which could be used on a tablet PC. To simulate a bone tumour in the pig femur, a cortical window was made in the diaphysis and bone cement was inserted. A total of 133 pig femurs were used and tumour resection was simulated with AR-assisted resection (164 resection in 82 femurs, half by an orthropaedic oncology expert and half by an orthopaedic resident) and resection with the conventional method (82 resection in 41 femurs). In the conventional group, resection was performed after measuring the distance from the edge of the condyle to the expected resection margin with a ruler as per routine clinical practice. The mean error of 164 resections in 82 femurs in the AR group was 1.71 mm (0 to 6). The mean error of 82 resections in 41 femurs in the conventional resection group was 2.64 mm (0 to 11) (p Augmented reality in bone tumour resection: An experimental study. Bone Joint Res 2017;6:137-143. © 2017 Cho et al.

  15. Inflation of stressed cylindrical tubes: an experimental study

    Science.gov (United States)

    Guo, Zhiming; Wang, Shibin; Li, Linan; Ji, Hongwei; Wang, Zhiyong; Cai, Songbao

    2014-06-01

    The inflation of an initially stressed cylindrical shell provides a good illustration of the phenomenon of the initiation and propagation of an instability, which shares the same mathematical and mechanical features with a variety of other strain localization phenomena in engineering structures and materials. The high speed CCD camera and digital image processing system were used to measure the 3D shape of the inflated cylindrical tube. The localized bulge of a cylindrical tube with closed ends forms when the internal pressure reaches a critical value Pcr. As more air is filled into the tube, the pressure drops but the radius at the centre of the bulge will increase until it reaches a maximum value rmax. With continued inflation, the pressure stays at a constant value Pp. The purpose of this study is to investigate the critical and propagation pressures in the tubes and the profile outside when the shells under axial tension and internal pressure were inflating. We focus on the influence of the axial tension on the critical pressure. In this paper the problem is explored through experimental efforts. A series of experiments were conducted on commercially available natural rubber latex tubes involving different geometries and initial axial tensions, which were regarded as isotropic, homogeneous, incompressible and hyper-elastic materials.

  16. Experimental Study on Effect of Electrode Location on Ion Current

    Directory of Open Access Journals (Sweden)

    Xu Hanqing

    2017-01-01

    Full Text Available In an attempt to use ion current method on a suction flame holder for combustion diagnosis, the position of the detection electrode that has the significant effect on ion current, should be investigated. The objective of this study was to experimentally investigate the ion current distribution in different combustion zones by changing the electrode length and streamwise location. An ion current acquisition system was built on basis of the principle of Langmuir probe, and experiments were conducted under different fuel-air ratios ranging from 0.008~0.022. The results suggest that the ion current distribution obeys the same regulation at different fuel-air ratios. With the electrode length increasing, the ion current increases first, then decreases, and finally presents a unimodal curve. As the electrode streamwise location increases, the ion current demonstrates a linear decrease rule. The maximum ion current is obtained in the case that the electrode length and streamwise location equals 60mm and 0.75. Since the larger ion current provides the wider range for setting the misfire threshold, the position where the maximum ion current occurs can be a better choice for arranging the electrode.

  17. Experimental studies on power transformer model winding provided with MOVs

    Directory of Open Access Journals (Sweden)

    G.H. Kusumadevi

    2017-05-01

    Full Text Available Surge voltage distribution across a HV transformer winding due to appearance of very fast rise time (rise time of order 1 μs transient voltages is highly non-uniform along the length of the winding for initial time instant of occurrence of surge. In order to achieve nearly uniform initial time instant voltage distribution along the length of the HV winding, investigations have been carried out on transformer model winding. By connecting similar type of metal oxide varistors across sections of HV transformer model winding, it is possible to improve initial time instant surge voltage distribution across length of the HV transformer winding. Transformer windings with α values 5.3, 9.5 and 19 have been analyzed. The experimental studies have been carried out using high speed oscilloscope of good accuracy. The initial time instant voltage distribution across sections of winding with MOV remains nearly uniform along length of the winding. Also results of fault diagnostics carried out with and without connection of MOVs across sections of winding are reported.

  18. Bipolar mood disorder, creativity and schizotypy: an experimental study.

    Science.gov (United States)

    Rybakowski, Janusz K; Klonowska, Paulina

    2011-01-01

    Our purpose was to make an experimental assessment of the elements of creativity and the features of schizotypy in patients with bipolar disorder, compared with healthy control subjects and to investigate the effect of an acute affective episode (depressed or manic) and the features of schizotypy on the measurements of creativity. Forty patients with bipolar disorder, and 48 age- and gender-matched control subjects were studied. For the assessment of creativity the Revised Art Scale and the 'inventiveness' part of the Berlin Intelligence Structure Test (BIS) were used. The Oxford-Liverpool Inventory of Feelings and Experiences was applied for estimation of schizotypy. The bipolar patients did not differ on the RAS scale from the control subjects but obtained significantly higher scores on the BIS-total as well as on the verbal part of the test. Their scores on the BIS scale during depression were significantly lower than in remission. The bipolar patients obtained significantly higher scores on all dimensions of schizotypy compared with the controls. These results confirm previous data showing higher scores on some creativity scales in bipolar patients compared with healthy subjects. They also corroborate a relationship between the features of schizotypy and creativity scores in bipolar patients. Copyright © 2011 S. Karger AG, Basel.

  19. Attentional bias in snus users: an experimental study.

    Directory of Open Access Journals (Sweden)

    Rune Aune Mentzoni

    Full Text Available The use of nicotine in the form of "snus" is substantial and increasing in some geographic areas, in particular among young people. It has previously been suggested that addictions may operate through a mechanism of attentional bias, in which stimuli representative of the dependent substance increase in salience, thus increasing the addictive behavior. However, this hypothesis has not been tested for the case of snus. The current experiment used a modified Stroop task and a dot-probe task to investigate whether 40 snus users show an attentional bias towards snus-relevant stimuli, compared to 40 non-snus users. There were no significant differences between the two groups on reaction times or accuracy on either Stroop or dot-probe task, thus failing to show an attentional bias towards snus-relevant stimuli for snus users. This could imply that other mechanisms may contribute to maintenance of snus use than for other addictions. However, this is the first experimental study investigating attentional bias in snus users, and more research is warranted.

  20. Experimental study of drop impacts on soap films

    Science.gov (United States)

    Yawar, Ali; Basu, Saikat; Concha, Andres; Bandi, Mahesh

    2015-11-01

    Impinging drops on flowing and static soap films demonstrate at least three distinct types of impact regimes: (a) the drop bounces off the film surface, (b) it coalesces with the downstream flow for a moving film and for static films it gets assimilated within the film, and (c) it pierces through the film. The interaction presents a unique opportunity to explore the impact of a quasi one-dimensional object on a two-dimensional fluid, much like a comet impacting on a thin atmosphere. We present a detailed experimental study of droplet impacts on soap film flow, for a number of film inclination angles and falling heights of the drop. Imaging techniques employed include sodium lamp interferometry to measure film thickness fluctuations and particle tracking velocimetry to measure the velocity field. Film thickness measures approximately 10 microns and the drop diameter is 1 mm. We mostly observe the bouncing-off regime for smaller inclination angles. However, at higher impact angles, puncturing of the film becomes a more common occurrence. We show that when the drop bounces off the film, there is a momentum transfer leading to vortex dipole shedding, along with the generation of capillary waves; an impulsive regime that may share correspondence with the locomotion of water striders.

  1. Immunology and Homeopathy. 3. Experimental Studies on Animal Models

    Directory of Open Access Journals (Sweden)

    Paolo Bellavite

    2006-01-01

    Full Text Available A search of the literature and the experiments carried out by the authors of this review show that there are a number of animal models where the effect of homeopathic dilutions or the principles of homeopathic medicine have been tested. The results relate to the immunostimulation by ultralow doses of antigens, the immunological models of the ‘simile’, the regulation of acute or chronic inflammatory processes and the use of homeopathic medicines in farming. The models utilized by different research groups are extremely etherogeneous and differ as the test medicines, the dilutions and the outcomes are concerned. Some experimental lines, particularly those utilizing mice models of immunomodulation and anti-inflammatory effects of homeopathic complex formulations, give support to a real effect of homeopathic high dilutions in animals, but often these data are of preliminary nature and have not been independently replicated. The evidence emerging from animal models is supporting the traditional ‘simile’ rule, according to which ultralow doses of compounds, that in high doses are pathogenic, may have paradoxically a protective or curative effect. Despite a few encouraging observational studies, the effectiveness of the homeopathic prevention or therapy of infections in veterinary medicine is not sufficiently supported by randomized and controlled trials.

  2. Ileoanal anastomosis with proximal ileal reservoir: an experimental study.

    Science.gov (United States)

    Schraut, W H; Block, G E

    1982-03-01

    Endorectal ileoanal anastomosis with proximal interposition of an ileal reservoir was evaluated experimentally in dogs as an approach to retain sphincteric control of defecation after proctocolectomy. Two months after the operative procedure, eight animals with a reservoir had four to eight semisolid stools per day and were continent. In contrast, six animals with straight ileoanal anastomosis were incontinent with 10 to 14 evacuations per day. Motility studies demonstrated a reduction of propulsive peristalsis within the undistended reservoir, which is considered the responsible factor for increased intestinal transit time and reduced stool frequency. Filling of the reservoir to capacity elicited strong peristaltic contractions, which may assure a more complete evacuation of the reservoir during defecation. Reservoir capacity increased substantially (150% to 200%) within 2 months but only to a minor degree thereafter, indicating that the reservoir does not dilate progressively into an atonic viscus. Motility patterns remained unaltered as the reservoir became more complaint with time. Mucosal alterations (flattening of villi, submucosal inflammation) were detected in the reservoir but did not result in nutritional defects within an observation period of 1 year.

  3. Experimental study of liquid drop impact onto a powder surface

    KAUST Repository

    Marston, Jeremy

    2010-11-01

    The initial dynamics of liquid drop impact onto powder surfaces is studied experimentally using high-speed photography. For a range of bed packing fractions, φ, liquid physical properties and impact velocities, ui, we observe a variety of phenomena that can be representative of a hydrophobic surface, a rough surface or a porous medium. The solids packing fraction in the bed, 0.38≤φ≤0.65, and the impact Weber number, 3.5≤We=ρDui 2/φ≤750, (where ρ, D and φ are the drop density, diameter and surface tension respectively) are shown to be the critical parameters governing the outcome of an impact. For high packing fractions, φ≳0.5, we show that the observed spreading, rebound and splashing can be broadly characterised in terms of the Weber number while for looser packing fractions, φ≲0.5, we observe powder ejectas and provide a qualitative description of the granule nucleation at the centre of the impact sites. © 2010 Elsevier B.V.

  4. Experimental study on titanium wire drawing with ultrasonic vibration.

    Science.gov (United States)

    Liu, Shen; Shan, Xiaobiao; Guo, Kai; Yang, Yuancai; Xie, Tao

    2018-02-01

    Titanium and its alloys have been widely used in aerospace and biomedical industries, however, they are classified as difficult-to-machine materials. In this paper, ultrasonic vibration is imposed on the die to overcome the difficulties during conventional titanium wire drawing processes at the room temperature. Numerical simulations were performed to investigate the variation of axial stress within the contacting region and study the change of the drawing stress with several factors in terms of the longitudinal amplitude and frequency of the applied ultrasonic vibration, the diameter reduction ratio, and the drawing force. An experimental testing equipment was established to measure the drawing torque and rotational velocity of the coiler drum during the wire drawing process. The result indicates the drawing force increases with the growth of the drawing velocity and the reduction ratio, whether with or without vibrations. Application of either form of ultrasonic vibrations contributes to the further decrease of the drawing force, especially the longitudinal vibration with larger amplitude. SEM was employed to detect the surface morphology of the processed wires drawn under the three circumstances. The surface quality of the drawn wires with ultrasonic vibrations was apparently improved compared with those using conventional method. In addition, the longitudinal and torsional composite vibration was more effective for surface quality improvement than pure longitudinal vibration, however, at the cost of weakened drawing force reduction effect. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Experimental Study Of Fog Water Harvesting By Stainless Steel Mesh

    Directory of Open Access Journals (Sweden)

    Nikhil R. Pawar

    2017-06-01

    Full Text Available The collection of fog water is a simple and sustainable technology to get hold of fresh water for various purposes. In areas where a substantial amount of fog can be obtained it is feasible to set up a stainless steel as well as black double layer plastic mesh structure for fog water harvesting. The mesh structure is directly exposed to the weather and the fog containing air is pushed through the active mesh surface by the wind. Afterward fog droplets are deposited on the active mesh area which combines to form superior droplets and run down into a gutter to storage by gravity. Fog water harvesting rates show a discrepancy from site to site. The scope of this experimental work is to review fog collection at SCOE Pune campus and to examine factors of success. This study is to synthesize the understanding of fog water harvesting in the institutional era and to analyze its benefits and boundaries for future development. The rate of fog water harvesting depends on the science of fog physics chemistry and its starring role in the hydrological cycle. This technology runs on zero energy and zeroes pollution level with cost of the benefit. The collected or treated clear water mainly could be used for different purposes as per requirement. For further development this technology public as well as government participation is needed.

  6. Numerical and experimental study of bistable plates for morphing structures

    Science.gov (United States)

    Nicassio, F.; Scarselli, G.; Avanzini, G.; Del Core, G.

    2017-04-01

    This study is concerned with the activation energy threshold of bistable composite plates in order to tailor a bistable system for specific aeronautical applications. The aim is to explore potential configurations of the bistable plates and their dynamic behavior for designing novel morphing structure suitable for aerodynamic surfaces and, as a possible further application, for power harvesters. Bistable laminates have two stable mechanical shapes that can withstand aerodynamic loads without additional constraint forces or locking mechanisms. This kind of structures, when properly loaded, snap-through from one stable configuration to another, causing large strains that can also be used for power harvesting scopes. The transition between the stable states of the composite laminate can be triggered, in principle, simply by aerodynamic loads (pilot, disturbance or passive inputs) without the need of servo-activated control systems. Both numerical simulations based on Finite Element models and experimental testing based on different activating forcing spectra are used to validate this concept. The results show that dynamic activation of bistable plates depend on different parameters that need to be carefully managed for their use as aircraft passive wing flaps.

  7. Scale dependence of acoustic velocities. An experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Gotusso, Angelamaria Pillitteri

    2001-06-01

    Reservoir and overburden data (e.g. seismic, sonic log and core data) are collected at different stages of field development, at different scales, and under different measurement conditions. A more precise reservoir characterization could be obtained by combining all the collected data. Reliable data may also be obtained from drill cuttings. This methodology can give data in quasi-real time, it is easily applicable, and cheap. It is then important, to understand the relationship between results obtained from measurements at different scales. In this Thesis acoustic velocities measured at several different laboratory scales are presented. This experimental study was made in order to give the base for the development of a model aiming to use/combine appropriately the data collected at different scales. The two main aspects analyzed are the experimental limitations due to the decrease in sample size and the significance of measurements in relation to material heterogeneities. Plexiglas, an isotropic, non-dispersive artificial material, with no expected scale effect, was used to evaluate the robustness of the measurement techniques. The results emphasize the importance of the wavelength used with respect to the sample length. If the sample length (L) is at least 5 time bigger than wavelength used ({lambda}), then the measured velocities do not depend on sample size. Leca stone, an artificial isotropic material containing spherical grains was used to evaluate the combined effects of technique, heterogeneities and sample length. The ratio between the scale of the heterogeneities and the sample length has to be taken in to account. In this case velocities increase with decreasing sample length when the ratio L/{lambda} is smaller than 10-15 and at the same time the ratio between sample length and grain size is greater than 10. Measurements on natural rocks demonstrate additional influence of grain mineralogy, shape and orientation. Firenzuola sandstone shows scale and

  8. Extremal quantum correlations: Experimental study with two-qubit states

    Energy Technology Data Exchange (ETDEWEB)

    Chiuri, A.; Mataloni, P. [Dipartimento di Fisica, Sapienza Universita di Roma, Piazzale Aldo Moro 5, I-00185 Roma (Italy); Istituto Nazionale di Ottica (INO-CNR), L.go E. Fermi 6, I-50125 Firenze (Italy); Vallone, G. [Dipartimento di Fisica, Sapienza Universita di Roma, Piazzale Aldo Moro 5, I-00185 Roma (Italy); Museo Storico della Fisica e Centro Studi e Ricerche Enrico Fermi, Via Panisperna 89/A, Compendio del Viminale, I-00184 Roma (Italy); Paternostro, M. [Centre for Theoretical Atomic, Molecular, and Optical Physics, School of Mathematics and Physics, Queen' s University, Belfast BT7 1NN (United Kingdom)

    2011-08-15

    We explore experimentally the space of two-qubit quantum-correlated mixed states, including frontier states as defined by the use of quantum discord and von Neumann entropy. Our experimental setup is flexible enough to allow for high-quality generation of a vast variety of states. We address quantitatively the relation between quantum discord and a recently suggested alternative measure of quantum correlations.

  9. Bargaining Power in Relational Contracts: An Experimental Study

    OpenAIRE

    Cordero Salas, Paula

    2011-01-01

    This paper provides experimental evidence of the economic impact from shifting bargaining power in relational contracts. I implement an experimental design that adjusts the bargaining power of sellers (agents) and the enforceability of the contract. I find that the vast majority of contracts take the form of efficiency wage contracts instead of contingent performance contracts when enforcement is partially incomplete and sellers have more bargaining power than buyers. The total contracted and...

  10. Increasing the rate of recycled asphalt: an experimental study

    Directory of Open Access Journals (Sweden)

    Marjan TUŠAR

    2014-09-01

    Full Text Available Asphalt is material that can be recycled. In particular reclaimed asphalt (RA contains aged binder, which limits the reuse of RA. In this study the rate of recycled asphalt was increased by adding a rejuvenator containing paraffin. The authors investigated the effect of the rejuvenator in laboratory and in plant prepared samples of asphalt mixture. In laboratory samples with different percentage of RA (0%, 10%, 30%, 50% and rejuvenator were prepared. In asphalt plant only asphalt mixture with highest amount of RA and rejuvenator and control mixture without RA were prepared. On samples were conducted different tests, e.g. determining softening point, Fraass breaking point, penetration, indirect tensile strength. Results on extracted bitumen showed increase in softening point and decrease in Fraass breaking point with increasing percentage of RA and rejuvenator, meaning that service temperature of binders increased. Asphalt samples prepared in asphalt plant were laid on test field. Asphalt with RA and rejuvenator was built in at lower temperature (round 100 °C. Mixtures with RA and rejuvenator have better low temperature properties confirmed with Thermal Stress Restrained Specimen Test (TSRST method, but are less resistant to compaction and less sensitive to water than control mixture. For comparison of long term behaviour wheel tracking test was performed on mixtures built in test field. A week after paving, the control mixture showed better properties, but one year later the results were opposite, asphalt containing RA and rejuvenator was more resistant to rutting. From the results of this experimental study the following was concluded: the amount of RA can be increased by using rejuvenator and the quality of such asphalt mixture is in most cases equal or even better than asphalt mixture made of virgin materials. By using RA we preserve nature, reduce usage of virgin raw materials, but it is cost effective only if recycling degree is high

  11. Rheology of lava flows on Mercury: An analog experimental study

    Science.gov (United States)

    Sehlke, A.; Whittington, A. G.

    2015-11-01

    We experimentally determined the rheological evolution of three basaltic analog compositions appropriate to Mercury's surface, during cooling, and crystallization. Investigated compositions are an enstatite basalt, and two magnesian basalts representing the compositional end-members of the northern volcanic plains with 0.19 wt % (NVP) and 6.26 wt % Na2O (NVP-Na). The viscosity-strain rate dependence of lava was quantified using concentric cylinder viscometry. We measured the viscosities of the crystal-free liquids from 1600°C down to the first detection of crystals. Liquidus temperatures of the three compositions studied are around 1360°C, and all three compositions are more viscous than Hawaiian basalt at the same temperature. The onset of pseudoplastic behavior was observed at crystal fractions ~0.05 to 0.10, which is consistent with previous studies on mafic lavas. We show that all lavas develop detectable yield strengths at crystal fractions around 0.20, beyond which the two-phase suspensions are better described as Herschel-Bulkley fluids. By analogy with the viscosity-strain rate conditions at which the pahoehoe to `a`a transition occurs in Kilauea basalt, this transition is predicted to occur at ~1260 ± 10°C for the enstatite basalt, at ~1285 ± 20°C for the NVP, and at ~1240 ± 40°C for the NVP-Na lavas. Our results indicate that Mercury lavas are broadly similar to terrestrial ones, which suggests that the extensive smooth lava plains of Mercury could be due to large effusion rates (flood basalts) and not to unusually fluid lavas.

  12. U-stitching splenorraphy technique: experimental and clinical study.

    Science.gov (United States)

    Tsaroucha, Alexandra K; Pitiakoudis, Michail S; Chanos, Georgios; Chiotis, Anestis S; Argyropoulou, Paraskevi I; Prassopoulos, Panos; Simopoulos, Constantinos E

    2005-04-01

    The aim of the present study was to describe the laboratory development and the subsequent clinical utility of the U-stitching technique for splenorraphy over the recent years in a general non-trauma hospital. Patients with splenectomies and patients treated conservatively during the same time period, are also presented. In the 15-year period from September 1988 until September 2003, 65 patients were diagnosed with splenic injury following admission to 2nd Department of Surgery, Democritus University Hospital, after blunt abdominal trauma. During the first 3 years, 14 patients were admitted; one of them was treated conservatively and 13 had splenectomies. Because computed tomography (CT) was not available at that time, these 14 patients form a control group. During the remaining 12-year period, 51 patients (39 male and 12 female; age, 4-82 years; mean, 31.1 years; SD, 19.7 years) were treated conservatively or surgically, either with splenectomy or with splenorraphy. Splenorraphy was performed using the U-stitching technique. This alternative splenorraphy technique was first tested on experimental models at 2nd Department of Surgery, Democritus University Hospital, then followed by successful clinical application. The medical records for these patients were reviewed to extract the data for the present study. Thirty-six patients (70.6% of 51 patients) were treated surgically; of these, 21 (41.2% of 51 patients) had splenectomy and 15 (29.4% of 51 patients) had splenorraphy. Non-operative treatment was initially given to 15 patients (29.4% of 51 patients). Two of them had delayed rupture of the spleen and underwent splenectomy (at 8 and 40 days). The total number of preserved spleens was 28 of 51 (54.9%). None of the patients with conservative treatment or splenorraphy died. One patient with splenectomy died later from overwhelming sepsis. Splenic salvage is now a treatment goal. If the patient is haemodynamically unstable and splenorraphy is possible, the U

  13. Laser welding of biological tissue: experimental studies in ophthalmology

    Science.gov (United States)

    Pini, Roberto; Rossi, Francesca; Menabuoni, Luca

    2006-04-01

    In this paper we present an original approach to laser welding of ocular media. Attention is focused on laser welding of the cornea and lens capsule. The process is based on the interaction of near infrared diode laser radiation (at 810 nm) with tissue that was previously stained with an Indocyanine Green solution in sterile water. The topical application of the chromophore makes possible a selective heating of the tissue, which results in a homogenous welding effect with low thermal damage to the surrounding tissue. Experimental tests were performed ex vivo on both capsule and cornea, and in vivo (rabbits) only on the cornea, in order to characterize the process as a whole. Spectrophotometric, biomechanical, and thermal measurements were carried out in order to study the laser-tissue interaction, while morphological, histological and auto-florescence microscopy analyses made during a follow-up study provided information on the healing process in welded rabbit corneas. The welding procedure was set up according to the type of tissue, with the staining procedure and irradiation conditions being optimized in each case. Our test indicated that: 1) laser welding of corneal wounds, which is a non contact technique performed at low continuous wave laser power (12 W/cm2), can be proposed as a support to or substitute for the standard suturing technique in cataract surgery and in penetrating keratoplasty (in corneal transplants); 2) laser welding of the lens capsule requires a "contact irradiating technique" in order to be efficiently performed, since the tissue is in underwater conditions, with single spot pulses of about 100 J/cm2 fluence and pulse duration around 100 ms. In the latter case, laser welding was proposed as a tool for assisting closure of the lens capsule after the lens refilling procedure (Phaco-ersatz), or for repairing capsular breaks induced by accidental traumas or produced intraoperatively.

  14. Mechanisms of Osteoarthritic Pain. Studies in Humans and Experimental Models

    Directory of Open Access Journals (Sweden)

    Annett Eitner

    2017-11-01

    Full Text Available Pain due to osteoarthritis (OA is one of the most frequent causes of chronic pain. However, the mechanisms of OA pain are poorly understood. This review addresses the mechanisms which are thought to be involved in OA pain, derived from studies on pain mechanisms in humans and in experimental models of OA. Three areas will be considered, namely local processes in the joint associated with OA pain, neuronal mechanisms involved in OA pain, and general factors which influence OA pain. Except the cartilage all structures of the joints are innervated by nociceptors. Although the hallmark of OA is the degradation of the cartilage, OA joints show multiple structural alterations of cartilage, bone and synovial tissue. In particular synovitis and bone marrow lesions have been proposed to determine OA pain whereas the contribution of the other pathologies to pain generation has been studied less. Concerning the peripheral neuronal mechanisms of OA pain, peripheral nociceptive sensitization was shown, and neuropathic mechanisms may be involved at some stages. Structural changes of joint innervation such as local loss and/or sprouting of nerve fibers were shown. In addition, central sensitization, reduction of descending inhibition, descending excitation and cortical atrophies were observed in OA. The combination of different neuronal mechanisms may define the particular pain phenotype in an OA patient. Among mediators involved in OA pain, nerve growth factor (NGF is in the focus because antibodies against NGF significantly reduce OA pain. Several studies show that neutralization of interleukin-1β and TNF may reduce OA pain. Many patients with OA exhibit comorbidities such as obesity, low grade systemic inflammation and diabetes mellitus. These comorbidities can significantly influence the course of OA, and pain research just began to study the significance of such factors in pain generation. In addition, psychologic and socioeconomic factors may aggravate

  15. Early differentiation of the Moon: Experimental and modeling studies and experimental and modeling studies of massif anorthosites

    Science.gov (United States)

    Longhi, John

    1994-01-01

    NASA grant NAG9-329 was in effect from 3/1/89 to 8/31/94, the last 18 months being a no-cost extension. While the grant was in effect, the P.I., coworkers, and students gave 22 talks and poster sessions at professional meetings, published 12 articles in referred journals (one more is in press, and another is in review), and edited 2 workshop reports relevant to this project. Copies of all the publications are appended to this report. The major accomplishments during the grant period have derived from three quarters: 1) the application of quantitative models of fractional crystallization and partial melting to various problems in planetary science, such as the petrogenesis of picritic glasses and mare basalts and the implications of the SNC meteorites for martian evolution; 2) an experimental study of silicate liquid immiscibility relevant to early lunar differentiation and the petrogenesis of evolved highlands rocks; and 3) experimental studies of massif anorthosites and related rocks that provide terrestrial analogs for the proposed origin of lunar anorthosites by multistage processes. The low-pressure aspects of the quantitative models were developed by the P.I. in the 1980s with NASA support and culminated with a paper comparing the crystallization of terrestrial and lunar lavas. The basis for the high-pressure modifications to the quantitative models is a data set gleaned from high pressure melting experiments done at Lamont and is supplemented by published data from other labs that constrain the baric and compositional dependences of various liquidus phase boundaries such as olivine/orthopyroxene, relevant to the melting of the mantles of the terrestrial planets. With these models it is possible to predict not only the thermal and compositional evolution of magmatic liquids ranging in composition from lumar mare basalt to terrestrial calc-alkaline basalts, but also the small increments of fractional melting that are produced when mantle rises adiabatically

  16. Experimental study on anelasticty of polycrystalline material for seismological application

    Science.gov (United States)

    Takei, Y.; Karasawa, F.

    2012-12-01

    Due to the recent progress in seismology, we can obtain highly-resolved seismic velocity structures in the upper mantle. In order to interpret the velocity structures in terms of temperature heterogeneity, chemical heterogeneity, and fluid/melt distribution, it is important to assess the quantitative effects of temperature, chemical composition, and fluid/melt on Vp and Vs. Although these effects at the ultrasonic frequencies (anharmonic effect, poroelastic effect) have been measured and assessed quantitatively, these effects at the seismic frequencies are subject to large uncertainty due to the uncertainty in rock anelasticity, which additionally causes modulus relaxation at lower frequencies (anelastic effect). Previous studies have shown that anelasticity of polycrystalline materials follows the similarity rule in which frequency normalized to the Maxwell frequency, f/fM, can be used as a master variable (Morris & Jackson, 2009a; McCarthy et al, 2012). The general applicability of this Maxwell frequency scaling shows that the anelastic relaxation in those experiments is caused by diffusionally accommodated grain boundary sliding (GBS) (Gribb & Cooper, 1998; McCarthy et al, 2012). However, normalized frequency of the existing experimental data is usually considerably lower than the seismic frequencies normalized to the Maxwell frequency of the upper mantle (f/fM=106-1010). Therefore, in order to clarify the mechanism and scaling law applicable to the seismic waves, we have to measure anelasticity at higher normalized frequencies. Theoretical models (e.g., Raj, 1975; Morris & Jackson, 2009b) predict that at higher normalized frequencies, dominant GBS mechanism changes from diffusionally accommodated GBS to elastically accommodated GBS. However, the transition frequency and total relaxation strength associated with the elastically accommodated GBS, which are important in the application to seismology, have so far been difficult to constrain theoretically

  17. Experimental plan for the fuel-oil study

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, M.P.; Levins, W.P.; Brown, M.A.

    1992-01-01

    An up-to-date assessment of the Weatherization Assistance Program (WAP) is being performed by the US Department of Energy WAP Division and the Oak Ridge National Laboratory. Five studies form the evaluation. Major goals of the Fuel-Oil Study are to estimate the fuel oil saved by the WAP in the Northeast during the 1990 and 1991 program years, identify and quantify non-energy impacts of the WAP, assess the cost effectiveness of the WAP within this submarket, and assess factors which may cause savings and cost effectiveness to vary. The study will only analyze single-family houses in the nine states in the Northeast census region and will be carried out over two heating seasons (1990 and 1991 WAP program years). A split-winter, pre- and post-weatherization experimental design with a control group will be used. Houses will be monitored over one winter. Energy conservation measures will be installed in the weatherized houses in January of each winter by the local WAP subgrantee. One hundred twenty five weatherized houses and 75 control houses will be monitored over the 1990--1991 winter; a different set of 200 houses will be monitored over the 1991--1992 winter. The houses will be evenly distributed among 25 subgrantees. Space-heating fuel-oil consumption, indoor temperature, and outdoor temperature data will be collected for all houses. Fuel-oil delivery data will be collected for each house monitored over the 1990--1991 winter for at least a year before weatherization. The delivery data will be analyzed to determine if the accuracy of the study can be improved by collecting fuel-oil delivery data on a larger sample of houses over the 1991--1992 winter. Detailed survey information will be obtained on all the houses. This information includes descriptive details of the house and its mechanical systems, details on household size and other demographics, and occupant answers to questions regarding comfort, safety, and operation of their space-heating system and house.

  18. A solar receiver-storage modular cascade based on porous ceramic structures for hybrid sensible/thermochemical solar energy storage

    Science.gov (United States)

    Agrafiotis, Christos; de Oliveira, Lamark; Roeb, Martin; Sattler, Christian

    2016-05-01

    The current state-of-the-art solar heat storage concept in air-operated Solar Tower Power Plants is to store the solar energy provided during on-sun operation as sensible heat in porous solid materials that operate as recuperators during off-sun operation. The technology is operationally simple; however its storage capacity is limited to 1.5 hours. An idea for extending this capacity is to render this storage concept from "purely" sensible to "hybrid" sensible/ thermochemical one, via coating the porous heat exchange modules with oxides of multivalent metals for which their reduction/oxidation reactions are accompanied by significant heat effects, or by manufacturing them entirely of such oxides. In this way solar heat produced during on-sun operation can be used (in addition to sensibly heating the porous solid) to power the endothermic reduction of the oxide from its state with the higher metal valence to that of the lower; the thermal energy can be entirely recovered by the reverse exothermic oxidation reaction (in addition to sensible heat) during off-sun operation. Such sensible and thermochemical storage concepts were tested on a solar-irradiated receiver- heat storage module cascade for the first time. Parametric studies performed so far involved the comparison of three different SiC-based receivers with respect to their capability of supplying solar-heated air at temperatures sufficient for the reduction of the oxides, the effect of air flow rate on the temperatures achieved within the storage module, as well as the comparison of different porous storage media made of cordierite with respect to their sensible storage capacity.

  19. Experimental and numerical study of globe valve housing

    Directory of Open Access Journals (Sweden)

    Mitrovic Nenad R.

    2017-01-01

    Full Text Available Complex structure experimental analysis has always been a huge challenge for researchers. Conventional experimental methods (e.g., strain gauges give only limited data sets regarding measurement on critical areas with high geometrical discontinuities. A 3D Digital Image Correlation method is an optical method that overcomes the limitations of conventional methods and enables full-field displacement and strain measurement of geometrically complex structures. System Aramis, based on Digital Image Correlation method, is used for experimental analysis and numerical model verification in this paper. Investigated complex structure is sphere/cylinder junction on globe valve housing subjected to axial loading. The highest experimentally measured von Mises strain values around 0.15% are recorded on cylinder/sphere intersection. Von Mises strain values on cylindrical and spherical part are several times smaller than on intersection itself. It is important to emphasize that, to the authors’ best knowledge, this is the first paper showing experimental results of 3D full and strain field of geometrically complex structure (sphere/cylinder intersection on the intersection itself on pressure equipment. It is proven that 3D Digital Image Correlation method is fast and versatile method for recording strain during loading of complex structures. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. TR35031 and Grant no. TR35040

  20. A comprehensive experimental and modeling study of isobutene oxidation

    KAUST Repository

    Zhou, Chong-Wen

    2016-03-17

    Isobutene is an important intermediate in the pyrolysis and oxidation of higher-order branched alkanes, and it is also a component of commercial gasolines. To better understand its combustion characteristics, a series of ignition delay time (IDT) and laminar flame speed (LFS) measurements have been performed. In addition, flow reactor speciation data recorded for the pyrolysis and oxidation of isobutene is also reported. Predictions of an updated kinetic model described herein are compared with each of these data sets, as well as with existing jet-stirred reactor (JSR) species measurements. IDTs of isobutene oxidation were measured in four different shock tubes and in two rapid compression machines (RCMs) under conditions of relevance to practical combustors. The combination of shock tube and RCM data greatly expands the range of available validation data for isobutene oxidation models to pressures of 50 atm and temperatures in the range 666–1715 K. Isobutene flame speeds were measured experimentally at 1 atm and at unburned gas temperatures of 298–398 K over a wide range of equivalence ratios. For the flame speed results, there was good agreement between different facilities and the current model in the fuel-rich region. Ab initio chemical kinetics calculations were carried out to calculate rate constants for important reactions such as H-atom abstraction by hydroxyl and hydroperoxyl radicals and the decomposition of 2-methylallyl radicals. A comprehensive chemical kinetic mechanism has been developed to describe the combustion of isobutene and is validated by comparison to the presently considered experimental measurements. Important reactions, highlighted via flux and sensitivity analyses, include: (a) hydrogen atom abstraction from isobutene by hydroxyl and hydroperoxyl radicals, and molecular oxygen; (b) radical–radical recombination reactions, including 2-methylallyl radical self-recombination, the recombination of 2-methylallyl radicals with