Experimental investigation of adsorption of NO and SO2 on modified activated carbon sorbent from flue gases

International Nuclear Information System (INIS)

Zhu, J.L.; Wang, Y.H.; Zhang, J.C.; Ma, R.Y.

2005-01-01

It is indicated that modified carbon is a practical sorbent for removal of NO and SO 2 from waste gases by the adsorption method. The ideal compositions for the prepared sorbent were 4.0 wt.% and 2.5 wt.% Na 2 CO 3 and KOH at the experimental conditions, respectively, shortened as ACNaK 2.5 . Experimental investigation showed that the sorbent had a comparatively high breakthrough adsorption capacity of NO and SO 2 , about 5.8 g (NO + SO 2 )/100 g sorbent. It is indicated that a relatively high adsorption temperature would benefit the sorbent adsorption capacities on NO and SO 2 at a certain space velocity and pressure. Further study revealed that the ACNaK 2.5 sorbent had good regenerability at the experimental conditions, which implied that the ACNaK 2.5 sorbent would be a useful sorbent for simultaneous removal of NO and SO 2 from waste gases by adsorption

Experimental study on removals of SO2 and NO(x) using adsorption of activated carbon/microwave desorption.

Science.gov (United States)

Ma, Shuang-Chen; Yao, Juan-Juan; Gao, Li; Ma, Xiao-Ying; Zhao, Yi

2012-09-01

Experimental studies on desulfurization and denitrification were carried out using activated carbon irradiated by microwave. The influences of the concentrations of nitric oxide (NO) and sulfur dioxide (SO2), the flue gas coexisting compositions, on adsorption properties of activated carbon and efficiencies of desulfurization and denitrification were investigated. The results show that adsorption capacity and removal efficiency of NO decrease with the increasing of SO2 concentrations in flue gas; adsorption capacity of NO increases slightly first and drops to 12.79 mg/g, and desulfurization efficiency descends with the increasing SO2 concentrations. Adsorption capacity of SO2 declines with the increasing of O2 content in flue gas, but adsorption capacity of NO increases, and removal efficiencies of NO and SO2 could be larger than 99%. Adsorption capacity of NO declines with the increase of moisture in the flue gas, but adsorption capacity of SO2 increases and removal efficiencies of NO and SO2 would be relatively stable. Adsorption capacities of both NO and SO2 decrease with the increasing of CO2 content; efficiencies of desulfurization and denitrification augment at the beginning stage, then start to fall when CO2 content exceeds 12.4%. The mechanisms of this process are also discussed. The prominent SO2 and NOx treatment techniques in power plants are wet flue gas desulfurization (FGD) and the catalytic decomposition method like selective catalytic reduction (SCR) or nonselective catalytic reduction (NSCR). However, these processes would have some difficulties in commercial application due to their high investment, requirement of expensive catalysts and large-scale equipment, and so on. A simple SO2 and NOx reduction utilizing decomposition by microwave energy method can be used. The pollutants control of flue gas in the power plants by the method of microwave-induced decomposition using adsorption of activated carbon/microwave desorption can meet the

Experimental investigation of a small-scale thermally driven pressurized adsorption chiller

KAUST Repository

Loh, Waisoong; Ismail, Azhar Bin; Ng, Kim Choon; Chun, Wongee

2015-01-01

This paper describes the successful operation of an adsorption cycle in a miniaturized adsorption chiller (AD). The experiments show that the bench-scale pressurized adsorption chiller (PAC) has been successfully designed, commissioned, and tested. Experimental results at various heat fl uxes, half-cycle operation time intervals, and a cooling load of up to 24 W are also presented. A COP ranging from 0.05 to 0.15 is achieved depending on the parameters of the experimental conditions. Most importantly, the cooling performance of the PAC is achieved at a low encasement temperature that is below ambient. Besides having a high cooling density, the PAC has almost no major moving parts except for the fan of the condenser and it permits quiet operation as compared to other active coolers.

Adsorption studies of iron(III)

Indian Academy of Sciences (India)

Adsorption of ferric ions by chitin was studied by the batch equilibration method. The influence of particle size and dosage of the adsorbant, contact time, initial concentration of the adsorbate and temperature were experimentally verified. The effect of anions like chloride, nitrate and sulphate and also of cations like zinc, ...

Molecular structure-adsorption study on current textile dyes.

Science.gov (United States)

Örücü, E; Tugcu, G; Saçan, M T

2014-01-01

This study was performed to investigate the adsorption of a diverse set of textile dyes onto granulated activated carbon (GAC). The adsorption experiments were carried out in a batch system. The Langmuir and Freundlich isotherm models were applied to experimental data and the isotherm constants were calculated for 33 anthraquinone and azo dyes. The adsorption equilibrium data fitted more adequately to the Langmuir isotherm model than the Freundlich isotherm model. Added to a qualitative analysis of experimental results, multiple linear regression (MLR), support vector regression (SVR) and back propagation neural network (BPNN) methods were used to develop quantitative structure-property relationship (QSPR) models with the novel adsorption data. The data were divided randomly into training and test sets. The predictive ability of all models was evaluated using the test set. Descriptors were selected with a genetic algorithm (GA) using QSARINS software. Results related to QSPR models on the adsorption capacity of GAC showed that molecular structure of dyes was represented by ionization potential based on two-dimensional topological distances, chromophoric features and a property filter index. Comparison of the performance of the models demonstrated the superiority of the BPNN over GA-MLR and SVR models.

Adsorption of cellulases onto sugar beet shreds and modeling of the experimental data

Directory of Open Access Journals (Sweden)

Ivetić Darjana Ž.

2014-01-01

Full Text Available This study investigated the adsorption of cellulases onto sugar beet shreds. The experiments were carried out using untreated, as well as dried and not dried dilute acid and steam pretreated sugar beet shreds at different initial enzyme loads. Both dilute acid and steam pretreatment were beneficial in respect of cellulases adsorption providing 8 and 9 times higher amounts of adsorbed proteins, respectively, in comparison to the results obtained with the untreated substrate. Although the use of higher solids load enabled by drying of pretreated substrates, could be beneficial for process productivity, at the same time it decreases the adsorption of enzymes. The obtained experimental data were fitted to five adsorption models, and the Langmuir model having the lowest residual sum of squares was used for the determination of adsorption parameters which were used to calculate the strength of cellulases binding to the substrates.[Projekat Ministarstva nauke Republike Srbije, br. TR 31002

Adsorption of saturated fatty acid in urea complexation: Kinetics and equilibrium studies

Science.gov (United States)

Setyawardhani, Dwi Ardiana; Sulistyo, Hary; Sediawan, Wahyudi Budi; Fahrurrozi, Mohammad

2018-02-01

Urea complexation is fractionation process for concentrating poly-unsaturated fatty acids (PUFAs) from vegetable oil or animal fats. For process design and optimization in commercial industries, it is necessary to provide kinetics and equilibrium data. Urea inclusion compounds (UICs) as the product is a unique complex form which one molecule (guest) is enclosed within another molecule (host). In urea complexation, the guest-host bonding exists between saturated fatty acids (SFAs) and crystalline urea. This research studied the complexation is analogous to an adsorption process. The Batch adsorption process was developed to obtain the experimental data. The ethanolic urea solution was mixed with SFA in certain compositions and adsorption times. The mixture was heated until it formed homogenous and clear solution, then it cooled very slowly until the first numerous crystal appeared. Adsorption times for the kinetic data were determined since the crystal formed. The temperature was maintained constant at room temperature. Experimental sets of data were observed with adsorption kinetics and equilibrium models. High concentration of saturated fatty acid (SFA) was used to represent adsorption kinetics and equilibrium parameters. Kinetic data were examined with pseudo first-order, pseudo second-order and intra particle diffusion models. Linier, Freundlich and Langmuir isotherm were used to study the equilibrium model of this adsorption. The experimental data showed that SFA adsorption in urea crystal followed pseudo second-order model. The compatibility of the data with Langmuir isotherm showed that urea complexation was a monolayer adsorption.

Adsorption of U(VI) onto kaolin studied by batch method

International Nuclear Information System (INIS)

Hongxia Zhang; Zhi Liu; Peizhuo Hu; Tonghuan Liu; Wangsuo Wu

2013-01-01

Adsorption of U(VI) on purified kaolin was studied by batch methods under ambient conditions, including contact time, pH, fulvic acid, etc. Three kinetic models were used to model the kinetic adsorption which was very well described by the pseudo-second-order rate equation, and the activation energy of adsorption was 52.20 kJ/mol. The Freundlich and Dubinin-Radushkevich models fitted the experimental data better than the Langmuir model for the adsorption and desorption isotherms. The thermodynamic parameters indicated that the adsorption of U(VI) on kaolin was an endothermic and spontaneous process. (author)

Experimental Adsorption Isotherm of Methane onto Activated Carbon at Sub- and Supercritical Temperatures

KAUST Repository

Rahman, Kazi Afzalur

2010-11-11

This paper presents the experimentally measured adsorption isotherm data for methane onto the pitch-based activated carbon type Maxsorb III for temperatures ranging from (120 to 220) K and pressures up to 1.4 MPa. These data are useful to study adsorbed natural gas (ANG) storage systems when the low temperature natural gas regasified from the liquid phase is considered to charge in the storage chamber. Adsorption parameters were evaluated from the isotherm data using the Tóth and Dubinin-Astakhov models. The isosteric heat of adsorption, which is concentration- and temperature-dependent, is extracted from the data. The Henry\\'s law coefficients for the methane/Maxsorb III pairs are evaluated at various temperatures. © 2010 American Chemical Society.

Thermodynamic study on the adsorption of strontium on polyantimonic acid exchanger

International Nuclear Information System (INIS)

Li Mingyu; Chen Jing; Wang Jianchen; Zhao Jing

2007-01-01

The adsorption of strontium on the polyantimonic acid adsorbent was studied. The equilibrium data for the adsorption of strontium on polyantimonic acid exchanger from aqueous solutions were obtained and correlated with Langmuir-type and Freundlich-type isotherm equation within the temperature range of 293-323 K and the experimental concentration range. Freundlich adsorption isotherms and the isosteric enthalpy indicate that the adsorption of strontium on polyantimonic acid is an endothermic process from aqueous solutions. The enthalpy, free energy, and entropy of adsorption were calculated. The results indicate that the adsorption process is a complex interaction of physical and chemical processes. The adsorption behaviors were reasonably explained. (authors)

Study on adsorption behavior of radioiodine gas using incense stick aerosol

International Nuclear Information System (INIS)

Murata, Mikio; Noguchi, Hiroshi; Kato, Shohei; Kokubu, Morinobu

1987-01-01

Adsorption of radioactive elemental iodine gas ( 131 I 2 ) on incense stick aerosol particles has been studied to provide basic data for a realistic and precise assessment of dose to the public due to radioiodine released from nuclear facilities. A mixture of iodine gas and aerosol was passed once through a glass vessel to cause the adsorption reaction. The adsorption was studied at different reaction times, initial I 2 gas concentrations and particle number concentrations. The results showed that the adsorption reached an equilibrium in about 2 min at the initial I 2 gas concentration of 10 -10 g/cm 3 . The proportion of iodine adsorbed by the aerosol particles was almost constant, about 25 % at the initial I 2 gas concentrations below 10 -11 g/cm 3 and at the reaction time of 1 min, and decreased with increase of the initial concentration over 10 -11 g/cm 3 . The adsorption isotherm of the aerosol for the gas was obtained from the experimental data. The semi-empirical equations to explain the adsorption reaction were also obtained based on the experimental data and the FUCHS's equation relating to vaporization of a droplet. The sticking probability in the equations was estimated to be 7.6 x 10 -3 . The calculated results using the equations were in good agreement with the experimental ones. (author)

Adsorptive desulfurization with CPO-27/MOF-74: an experimental and computational investigation.

Science.gov (United States)

Van de Voorde, Ben; Hezinová, Markéta; Lannoeye, Jeroen; Vandekerkhove, Annelies; Marszalek, Bartosz; Gil, Barbara; Beurroies, Isabelle; Nachtigall, Petr; De Vos, Dirk

2015-04-28

By combining experimental adsorption isotherms, microcalorimetric data, infrared spectroscopy and quantum chemical calculations the adsorption behaviour of the CPO-27/MOF-74 series (Ni, Co, Mg, Cu, and Zn) in the desulfurization of fuels is evaluated. The results show a clear influence of the metal ion on the adsorption capacity and affinity for S-heterocyclic compounds, with CPO-27(Ni) being the best performing material both in terms of capacity and affinity. The microcalorimetric data and infrared spectroscopy confirm the high affinity of CPO-27(Ni) for thiophene and similar compounds, while the computational data reveal that the origin of this outstanding adsorption performance is the strong sulfur-metal interaction.

Experimental Adsorption Isotherm of Methane onto Activated Carbon at Sub- and Supercritical Temperatures

KAUST Repository

Rahman, Kazi Afzalur; Loh, Wai Soong; Yanagi, Hideharu; Chakraborty, Anutosh; Saha, Bidyut Baran; Chun, Won Gee; Ng, Kim Choon

2010-01-01

This paper presents the experimentally measured adsorption isotherm data for methane onto the pitch-based activated carbon type Maxsorb III for temperatures ranging from (120 to 220) K and pressures up to 1.4 MPa. These data are useful to study

Selective adsorption of volatile organic compounds in micropore aluminum methylphosphonate-alpha: a combined molecular simulation-experimental approach.

Science.gov (United States)

Herdes, Carmelo; Valente, Anabela; Lin, Zhi; Rocha, João; Coutinho, João A P; Medina, Francisco; Vega, Lourdes F

2007-06-19

Results concerning the adsorption capacity of aluminum methylphosphonate polymorph alpha (AlMePO-alpha) for pure ethyl chloride and vinyl chloride by measured individual adsorption isotherms of these pure compounds are presented and discussed here. The experimental data supports the idea of using these materials as selective adsorbents for separating these compounds in mixtures. To explore this possibility further, we have performed grand canonical Monte Carlo simulations using a recently proposed molecular simulation framework for gas adsorption on AlMePO, and the results are presented here. The molecular model of the material was used in a purely transferable manner from a previous work (Herdes, C.; Lin, Z.; Valente, A.; Coutinho, J. A. P.; Vega, L. F. Langmuir 2006, 22, 3097). Regarding the molecular model of the fluids, an existing model for ethyl chloride was improved to capture the experimental dipole value better; an equivalent force field for the vinyl chloride molecule was also developed for simulation purposes. Simulations of the pure compounds were found to be in excellent agreement with the measured experimental data at the three studied temperatures. Simulations were also carried out in a purely predictive manner as a tool to find the optimal conditions for the selective adsorption of these compounds prior experimental measurements are carried out. The influence of the temperature and the bulk composition on the adsorption selectivity was also investigated. Results support the use of AlMePO-alpha as an appropriate adsorbent for the purification process of vinyl chloride, upholding the selective adsorption of ethyl chloride.

Adsorption of uranium composites onto saltrock oxides - experimental and theoretical study.

Science.gov (United States)

Ivanova, Bojidarka; Spiteller, Michael

2014-09-01

The study encompassed experimental mass spectrometric and theoretical quantum chemical studies on adsorption of uranium species in different oxidation states of the metal ion, and oxides of UxOy(n+) type, where x = 1 or 3, y = 2 or 8, and n = 0, 1 or 2 onto nanosize-particles of saltrock oxides MO (M = Mg(II), Ca(II), Ni(II), Co(II), Sr(II) or Ba(II)), M2Oy (M = Au(III) or Ag(I), y = 3 or 1) silicates 3Al2O3.2SiO2, natural kaolinite (Al2O2·2SiO2·2H2O), illite (K0.78Ca0.02Na0.02(Mg0.34Al1.69Fe(III)0.02)[Si3.35Al0.65]O10(OH)2·nH2O), CaSiO3, 3MgO·4SiO2,H2O, and M(1)M(2)(SiO4)X2 (M(1) = M(2) = Al or M(1) = K, M(2) = Al, X = F or Cl), respectively. The UV-MALDI-Orbitrap mass spectrometry was utilized in solid-state and semi-liquid colloidal state, involving the laser ablation at λex = 337.2 nm. The theoretical modeling and experimental design was based on chemical-, physico-chemical, physical and biological processes involving uranium species under environmental conditions. Therefore, the results reported are crucial for quality control and monitoring programs for assessment of radionuclide migration. They impact significantly the methodology for evaluation of human health risk from radioactive contamination. The study has importance for understanding the coordination and red-ox chemistry of uranium compounds as well. Due to the double nature of uranium between rare element and superconductivity like materials as well as variety of oxidation states ∈ (+1)-(+6), the there remain challenging areas for theoretical and experimental research, which are of significant importance for management of nuclear fuel cycles and waste storage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Adsorption studies of iron(III) on chitin

Indian Academy of Sciences (India)

Unknown

of particle size and dosage of the adsorbant, contact time, initial concentration of the adsorbate and tem- perature were experimentally ... Adsorption; chitin; variable parameters; fraction of adsorption; temperature effect. 1. Introduction. Iron is one of the ... about the presence of iron in drinking water is its ob- jectionable taste.

Study on adsorption mechanism of ammonia nitrogen in wastewater by natural heulandite

Directory of Open Access Journals (Sweden)

Xuekai JIN

2018-02-01

Full Text Available In order to explore the adsorption mechanism and optimal regeneration method of natural heulandite to high ammonia nitrogen wastewater, the natural heulandite from Hebei Province is selected as the research object. The adsorption kinetics, adsorption isotherms and adsorption thermodynamics are studied by single factor test. The results show that the adsorption process of ammonia nitrogen on heulandite with particle size range of 50~600 μm complies with the quasi-second order kinetic equation with ammonia nitrogen concentration of 500 mg/L at temperature of 25 ℃. Particle diffusion and liquid film diffusion are the dominated process of the adsorption. The adsorption capacity of heulandite is 7.81 mg/g at temperature of 45 ℃. The adsorption isotherm of ammonia nitrogen on the experimental heulandite is fitted well with Freundlich model. Gibbs free energy ΔG is calculated to be less than zero, indicating that the adsorption of ammonia nitrogen on the experimental heulandite is a spontaneous endothermic reaction. Additionally, the adsorption capacity of heulandite increases with appropriate increaseing in temperature. The optimal regeneration solvent of the saturated heulandite is 0.1 mol/L of NaCl, with which the desorption rate increases to 79%, and the times of elution and regeneration are more than 5. The results of this study can improve the economic benefits and environmental value of heulandite in the treatment of ammonia nitrogen wastewater. It can be seen that heulandite in the industrial wastewater treatment has broad prospects for application.

Study on Shale Adsorption Equation Based on Monolayer Adsorption, Multilayer Adsorption, and Capillary Condensation

Directory of Open Access Journals (Sweden)

Qing Chen

2017-01-01

Full Text Available Shale gas is an effective gas resource all over the world. The evaluation of pore structure plays a critical role in exploring shale gas efficiently. Nitrogen adsorption experiment is one of the significant approaches to analyze pore size structure of shale. Shale is extremely heterogeneous due to component diversity and structure complexity. Therefore, adsorption isotherms for homogeneous adsorbents and empirical isotherms may not apply to shale. The shape of adsorption-desorption curve indicates that nitrogen adsorption on shale includes monolayer adsorption, multilayer adsorption, and capillary condensation. Usually, Langmuir isotherm is a monolayer adsorption model for ideal interfaces; BET (Brunauer, Emmett, Teller adsorption isotherm is a multilayer adsorption model based on specific assumptions; Freundlich isotherm is an empirical equation widely applied in liquid phase adsorption. In this study, a new nitrogen adsorption isotherm is applied to simultaneously depict monolayer adsorption, multilayer adsorption, and capillary condensation, which provides more real and accurate representation of nitrogen adsorption on shale. In addition, parameters are discussed in relation to heat of adsorption which is relevant to the shape of the adsorption isotherm curve. The curve fitting results indicate that our new nitrogen adsorption isotherm can appropriately describe the whole process of nitrogen adsorption on shale.

Mathematical modeling and experimental breakthrough curves of carbon dioxide adsorption on metal organic framework CPM-5.

Science.gov (United States)

Sabouni, Rana; Kazemian, Hossein; Rohani, Sohrab

2013-08-20

It is essential to capture carbon dioxide from flue gas because it is considered one of the main causes of global warming. Several materials and different methods have been reported for CO2 capturing including adsorption onto zeolites and porous membranes, as well as absorption in amine solutions. All such methods require high energy input and high cost. A new class of porous materials called Metal Organic Frameworks (MOFs) exhibited excellent performance in extracting carbon dioxide from a gas mixture. In this study, the breakthrough curves for the adsorption of carbon dioxide on CPM-5 (crystalline porous materials) were obtained experimentally and theoretically using a laboratory-scale fixed-bed column at different experimental conditions such as feed flow rate, adsorption temperature, and feed concentration. It was found that the CPM-5 has a dynamic CO2 adsorption capacity of 11.9 wt % (2.7 mmol/g) (corresponding to 8 mL/min, 298 K, and 25% v/v CO2). The tested CPM-5 showed an outstanding adsorption equilibrium capacity (e.g., 2.3 mmol/g (10.2 wt %) at 298 K) compared to other adsorbents, which can be considered as an attractive adsorbent for separation of CO2 from flue gas.

Adsorption study of Ammonia Nitrogen by watermelon rind

Science.gov (United States)

Ibrahim, A.; Yusof, L.; Beddu, N. S.; Galasin, N.; Lee, P. Y.; Lee, R. N. S.; Zahrim, A. Y.

2016-06-01

The utilization of fruit waste for low-cost adsorbents as a replacement for costly conventional methods of removing ammonia nitrogen from wastewater has been reviewed. The adsorption studies were conducted as a function of contact time and adsorbent dosage and it were carried out on four different adsorbents; fresh watermelon rind and modified watermelon rind with sodium hydroxide (NaOH), potassium hydroxide (KOH) and sulphuric acid (H2SO4). Adsorbents were tested for characterization by using zeta potential test and all samples shows negative values thus makes it favourable for the adsorption process. The batch experimental result showed that adsorption process is rapid and equilibrium was established within 40 minutes of contact time. The ammonia nitrogen removal rate amounted in range of 96% to 99%, and the adsorption capacities were in range of 1.21 to 1.24 mg/g for all four different types of adsorbents used.

A Study on Astrazon Black AFDL Dye Adsorption onto Vietnamese Diatomite

Directory of Open Access Journals (Sweden)

Bui Hai Dang Son

2016-01-01

Full Text Available In the present paper, the adsorption of Astrazon Black AFDL dye onto Vietnamese diatomite has been demonstrated. The diatomite was characterized by XRD, SEM, TEM, EDS, and nitrogen adsorption/desorption isotherms. The results show that diatomite mainly constituted centric type frustules characterized by pores as discs or as cylindrical shapes. The adsorption kinetics and isotherms of dye onto Vietnam diatomite were investigated. The experimental data were fitted well to both Freundlich and Langmuir in the initial concentration range of 400–1400 mg L−1. The average value of maximum adsorption capacity, qm, calculated from Freundlich equation is statistically similar to the average value of maximum monolayer adsorption capacity calculated from Langmuir equation. The thermodynamic parameters evaluated from the temperature dependent on adsorption isotherms in the range of 303–343 K show that the adsorption process was spontaneous and endothermic. The Webber and pseudo-first/second-order kinetic models were used to analyze the mechanism of adsorption. The piecewise linear regression and Akaike’s Information Criterion were used to analyze experimental data. The results show that the dye adsorption onto diatomite was film diffusion controlled and the goodness of fit of experimental data for kinetics modes was dependent on the initial concentration.

Experimental study on improved two-bed silica gel-water adsorption chiller

Energy Technology Data Exchange (ETDEWEB)

Xia Zaizhong [Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200030 (China)], E-mail: xzz@sjtu.edu.cn; Wang Dechang; Zhang Jincui [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China)

2008-06-15

A novel silica gel-water adsorption chiller with two chambers has been built in Shanghai Jiao Tong University (SJTU). This chiller combines two single bed systems (basic system) without any vacuum valves. One adsorber, one condenser and one evaporator are housed in the same chamber to constitute one adsorption/desorption unit. In this work, the chiller is developed and improved. The improved chiller is composed of three vacuum chambers: two adsorption/desorption vacuum chambers (the same structure as the former chiller) and one heat pipe working vacuum chamber. The evaporators of these two adsorption/desorption units are combined by a heat pipe. So, no valves are installed in the chilled water sub system and one vacuum valve connects the two adsorption/desorption chambers together to improve its performance. The performance of the chiller is tested. As the results, the refrigerating capacity and the COP of the chiller are, respectively, 8.69 kW and 0.388 for the heat source temperature of 82.5 deg. C, the cooling water temperature of 30.4 deg. C and the chilled water outlet temperature of 11.9 deg. C. For a chilled water outlet temperature of 16.5 deg. C, the COP reaches 0.432, while the refrigerating capacity is near 11 kW. There is an improvement of at least 12% for the COP compared with the former chillers.

Experimental study on improved two-bed silica gel-water adsorption chiller

Energy Technology Data Exchange (ETDEWEB)

Xia, Zaizhong [Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200030 (China); Wang, Dechang; Zhang, Jincui [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China)

2008-06-15

A novel silica gel-water adsorption chiller with two chambers has been built in Shanghai Jiao Tong University (SJTU). This chiller combines two single bed systems (basic system) without any vacuum valves. One adsorber, one condenser and one evaporator are housed in the same chamber to constitute one adsorption/desorption unit. In this work, the chiller is developed and improved. The improved chiller is composed of three vacuum chambers: two adsorption/desorption vacuum chambers (the same structure as the former chiller) and one heat pipe working vacuum chamber. The evaporators of these two adsorption/desorption units are combined by a heat pipe. So, no valves are installed in the chilled water sub system and one vacuum valve connects the two adsorption/desorption chambers together to improve its performance. The performance of the chiller is tested. As the results, the refrigerating capacity and the COP of the chiller are, respectively, 8.69 kW and 0.388 for the heat source temperature of 82.5 C, the cooling water temperature of 30.4 C and the chilled water outlet temperature of 11.9 C. For a chilled water outlet temperature of 16.5 C, the COP reaches 0.432, while the refrigerating capacity is near 11 kW. There is an improvement of at least 12% for the COP compared with the former chillers. (author)

Reservoir capacity estimates in shale plays based on experimental adsorption data

Science.gov (United States)

Ngo, Tan

from different measurement techniques using representative fluids (such as CH4 and CO2) at elevated pressures, and the adsorbed density can range anywhere between the liquid and the solid state of the adsorbate. Whether these discrepancies are associated with the inherent heterogeneity of mudrocks and/or with poor data quality requires more experiments under well-controlled conditions. Nevertheless, it has been found in this study that methane GIP estimates can vary between 10-45% and 10-30%, respectively, depending on whether the free or the total amount of gas is considered. Accordingly, CO2 storage estimates range between 30-90% and 15-50%, due to the larger adsorption capacity and gas density at similar pressure and temperature conditions. A manometric system has been designed and built that allows measuring the adsorption of supercritical fluids in microporous materials. Preliminary adsorption tests have been performed using a microporous 13X zeolite and CO 2 as an adsorbing gas at a temperature of 25oC and 35oC and at pressures up to 500 psi. Under these conditions, adsorption is quantified with a precision of +/- 3%. However, relative differences up to 15-20% have been observed with respect to data published in the literature on the same adsorbent and at similar experimental conditions. While it cannot be fully explained with uncertainty analysis, this discrepancy can be reduced by improving experiment practice, thus including the application of a higher adsorbent's regeneration temperature, of longer equilibrium times and of a careful flushing of the system between the various experimental steps. Based on the results on 13X zeolite, virtual tests have been conducted to predict the performance of the manometric system to measure adsorption on less adsorbing materials, such as mudrocks. The results show that uncertainties in the estimated adsorbed amount are much more significant in shale material and they increase with increasing pressure. In fact, relative

Humidity adsorption and transfer in hygroscopic materials. Percolation-type approach and experimentation

International Nuclear Information System (INIS)

Quenard, Daniel

1989-01-01

Water vapor adsorption and transfer in microporous media are studied by using a 3 level hierarchical approach. At the microscopic level (pore size), we describe the basic phenomena (adsorption/desorption, capillary condensation, molecular and Knudsen diffusion, Hagen-Poiseuille flow) that occur during the isotherm water vapor transport in a single cylindrical pore, at the steady state. The transport through a condensed pore is taken into account by its 'vapor equivalent flow' and we underline that capillary condensation may cause vapor flow amplification of several orders of magnitude. We suggest to use an electrical analogy between a cylindrical pore and a Zener diode. Then at the mesoscopic level (material size), we introduce pore networks to provide use with a simplified description of the microstructure. Three types of networks are studied: square, triangular and honeycomb. By using a random distribution of the single cylindrical pores on the 2D networks, we are able to estimate the sorption isotherms and the water vapor permeability which are the two essential characteristics to understand the behaviour of materials towards humidity. To develop this approach we refer to the percolation concept and we use most of its principal results. To estimate the adsorption isotherms we introduce a surface adsorption model and we use the KELVIN-LAPLACE equation. Hysteresis appears naturally thanks to the 'ink-bottle' phenomenon and it is all the more important since the network is ill-connected. The water vapor permeability is calculated thanks to the electrical analogy (cylindrical pore-Zener diode). We emphasize an important amplification of the equivalent permeability when the relative humidity reaches a threshold value. This phenomenon provides use with a possible explanation of numerous experimental results. The respective effects of pore size distribution and temperature, on sorption isotherms and permeability, are presented. We present several

Experimental investigation on the optimal performance of Zeolite-water adsorption chiller

KAUST Repository

Myat, Aung

2013-02-01

This paper presents the performance testing of Zeolite adsorption cooling system driven by low grade waste heat source extracted from prime mover\\'s exhaust, power plant\\'s exhaust and the solar energy. The adsorbent FAM Z01 is used as an adsorbent in the adsorption chiller facility. Owing to its large equilibrium pore volume, it has the high affinity for the water vapor adsorbate. The key advantages of the Zeolite adsorption cooling system are: (i) it has no moving parts rendering less maintenance, (ii) the energy efficient means of cooling by the adsorption process with a low temperature heat source, (iii) the use of vapor pipes are replaced by self actuating vapor valves rendering smaller footprint area and (iv) it is environmental friendly with low carbon footprint. The experimental investigations were carried out for Zeolite adsorption chiller at different key operating conditions namely (i) heat source temperature, (ii) the cycle time and (iii) the heat recovery time. It is investigated that performance of coefficient (COP) of this system could be as high as 0.48 while the waste heat source temperature is applicable as low as 55 °C. © 2012.

Equilibrium and Thermodynamic Studies of Methane Adsorption on Multi-Walled Carbon Nanotube

OpenAIRE

Sanaz. Monemtabary; Mojtaba Shariati Niasar; Mohsen Jahanshahi; Ali Asghar Ghoreyshi

2013-01-01

In this work, The adsorption of methane onto multi-walled carbon nanotubes (MWCNTs) was studied, in which the influences of temperatureand pressure were investigated. The physical properties of the MWCNT were systematically characterised by Scanning Electron Microscopy (SEM) and Brunauere-Emmette-Teller (BET) surface area measurements. The equilibrium adsorption data were analyzed using threecommon adsorption models: Langmuir, Freundlich and Sips. All of the models fit the experimental result...

Dynamics of arsenic adsorption in the targeted arsenic-safe aquifers in Matlab, south-eastern Bangladesh: Insight from experimental studies

International Nuclear Information System (INIS)

Robinson, Clare; Broemssen, Mattias von; Bhattacharya, Prosun; Haeller, Sara; Biven, Annelie; Hossain, Mohammed; Jacks, Gunnar; Ahmed, Kazi Matin; Hasan, M. Aziz; Thunvik, Roger

2011-01-01

Research highlights: → Adsorption behaviour of shallow oxidized sediments from Matlab Region in SE Bangladesh is investigated. → Oxidized sediments have a high capacity to adsorb arsenic. → Adsorption capacity will be reduced by high concentration of reactive organic C. → Monitoring of groundwater quality over 5 year period shows relatively stable water chemistry. - Abstract: Targeting shallow low-As aquifers based on sediment colour may be a viable solution for supplying As-safe drinking water to rural communities in some regions of Bangladesh and West Bengal in India. The sustainability of this solution with regard to the long-term risk of As-safe oxidized aquifers becoming enriched with As needs to be assessed. This study focuses on the adsorption behaviour of shallow oxidized sediments from Matlab Region, Bangladesh, and their capacity to attenuate As if cross-contamination of the oxidized aquifers occurs. Water quality analyses of samples collected from 20 tube-wells in the region indicate that while there may be some seasonal variability, the groundwater chemistry in the reduced and oxidized aquifers was relatively stable from 2004 to 2009. Although sediment extractions indicate a relatively low amount of As in the oxidized sediments, below 2.5 mg kg -1 , batch isotherm experiments show that the sediments have a high capacity to adsorb As. Simulations using a surface complexation model that considers adsorption to amorphous Fe(III) oxide minerals only, under-predict the experimental isotherms. This suggests that a large proportion of the adsorption sites in the oxidized sediments may be associated with crystalline Fe(III) oxides, Mn(IV) and Al(III) oxides, and clay minerals. Replicate breakthrough column experiments conducted with lactose added to the influent solution demonstrate that the high adsorption capacity of the oxidized sediments may be reduced if water drawn down into the oxidized aquifers contains high levels of electron donors such as

Water adsorption on goethite: Application of multilayer adsorption models

Science.gov (United States)

Hatch, C. D.; Tumminello, R.; Meredith, R.

2016-12-01

Adsorbed water on the surface of atmospheric mineral dust has recently been shown to significantly affect the ability of mineral dust aerosol to act as cloud condensation nuclei. We have studied water adsorption as a function of relative humidity (RH) on goethite (α-FeO(OH)), a common component of atmospheric mineral dust. The goethite surface area and particle size was determined using BET analysis and with N2 as an adsorbate and scanning electron microscopy, respectively. Water adsorption on the sample was monitored using horizontal attenuated total reflectance Fourier transform infrared (HATR-FTIR) spectroscopy equipped with a flow cell. Water content was determined using Beer's law and the optical constants for bulk water. The results were analyzed using Type II adsorption isotherms to model multilayer adsorption, including BET (Brunauer, Emmet and Teller), FHH (Frenkel, Halsey and Hill) and Freundlich. BET fits to experimental data provide parameters of monolayer coverage, while the FHH and Freundlich isotherms provide insights into multilayer adsorption mechanisms. Results indicate that goethite contains 5% H2O by mass at 50% RH, which increases to 12% by mass at 90% RH. Adsorption parameters and experimental results will be presented.

Study of 63Ni adsorption on NKF-6 zeolite

International Nuclear Information System (INIS)

Zhang Hui; Yu Xianjin; Chen Lei; Jing Yongjie; Ge Zhiwei

2010-01-01

The adsorption of 63 Ni from aqueous solutions using NKF-6 zeolite was investigated by a batch technique under ambient conditions. The adsorption was investigated as a function of contact time, pH, ionic strength, foreign ions, humic substances (FA/HA) and temperature. The kinetic adsorption was well described by the pseudo-second-order rate equation. The adsorption of 63 Ni on NKF-6 zeolite was strongly dependent on pH and ionic strength, and the adsorption of 63 Ni increased with increasing NKF-6 zeolite content. At low pH values, the presence of FA enhanced the adsorption of 63 Ni on NKF-6 zeolite, but the presence of HA had no drastic effect. At high pH values, the presence of FA or HA decreased the adsorption of 63 Ni on NKF-6 zeolite. The adsorption isotherms were well represented by the Langmuir model. The thermodynamic parameters (i.e., ΔH 0 , ΔS 0 and ΔG 0 ) for the adsorption of 63 Ni were determined from the temperature dependent isotherms at 293.15, 313.15 and 333.15 o K, respectively, and the results indicate that the adsorption reaction was favored at high temperature. The results suggest that the adsorption process of 63 Ni on NKF-6 zeolite is spontaneous and endothermic. - Research highlights: → As an economical and efficient method, adsorption technique has been widely applied in the disposal of wastewaters. The study of 63 Ni on NKF-6 zeolite, especially the thermodynamic data of 63 Ni adsorption on NKF-6 zeolite and the effect of humic substances on 63 Ni uptake to humic-zeolite hybrids, is still scarce. In this paper, the sorption of 63 Ni on NKF-6 zeolite is studied as a function of various environmental conditions such as contact time, pH, ionic strength, foreign ions, humic substances and temperature. Based on the obtained experimental results, the adsorption mechanism of 63 Ni on NKF-6 zeolite is stated in detail. This study will have an important reference value in evaluating the physiochemical behavior of radionuclide 63 Ni.

Water on TiO2 studied by work function change: adsorption in cycles

International Nuclear Information System (INIS)

Bundaleski, Nenad; Silva, Ana G; Jean-Shaw, Bobbie; Teodoro, Orlando; Moutinho, Augusto

2013-01-01

The nature of water adsorption on TiO 2 (110) rutile surface attracts a lot of attention for quite some time. In spite of the considerable experimental and theoretical efforts a lot of details remain unclear. We have been using work function study to follow the adsorption of water on TiO 2 at room temperature, and interpreted the results in terms of fast dissociative adsorption on bridging oxygen vacancies (BOV) and much slower non-dissociative adsorption on Ti 5f rows. Additionally, we concluded that water from Ti 5f rows efficiently desorbs at room temperature which is not the case for BOV adsorption sites. Here we propose a novel experimental approach which consists of monitoring in real-time the work function change during cycles of water adsorption. Since desorption at BOVs does not take place at room temperature, this method allows us to resolve the adsorption dynamics on the two adsorption sites. The first results changed our understanding of the phenomenon: we show that both, adsorption on BOVs and Ti 5f are both very fast. Additionally, slow exponential decay of the work function is observed, which is not directly related to water adsorption. The possible explanation of the third slow contribution could be related to the migration of hydrogen atoms along the bridging oxygen rows.

Mechanical and experimental study on freeze proof solar powered adsorption cooling tube using active carbon/methanol working pair

International Nuclear Information System (INIS)

Zhao Huizhong; Zhang Min; Liu Zhenyan; Liu Yanling; Ma Xiaodong

2008-01-01

The freeze proof solar cooling tube, which can produce cooling capacity with the refrigerant temperature below 0 deg. C using solar light as energy and active carbon-methanol as working pair, was firstly designed and made in this research. This paper focused on mechanical and experimental study on a freeze proof solar powered adsorption cooling tube. The following experimental results could be concluded: at the solar radiation value between 15.3 and 17.1 MJ m -2 , the highest adsorbent bed temperature is below 110 deg. C. The freeze proof solar cooling tube's cooling capacity was about 87-99 kJ, and the coefficient of performance (COP) was more than 0.11 when the evaporation temperature was about -4 deg. C

The adsorption of mercury on tungsten (100) studied by ultra-violet photoelectron spectroscopy

International Nuclear Information System (INIS)

Egelhoff, W.F. Jr.; Perry, D.L.; Linnett, J.W.

1976-01-01

In recent years, photoelectron spectroscopy has been applied to the study of adsorption on several metal surfaces. A popular choice of substrate has been the 100 face of single crystal tungsten, since adsorption on this surface has been well-characterised by a wide variety of experimental techniques. In this letter a study of the adsorption of mercury on W(100) by ultra-violet photoelectron spectroscopy (UPS) is reported. These results, seen in the context of previous UPS studies of chemisorption, show a number of interesting features. (Auth.)

Experimental design based response surface methodology optimization of ultrasonic assisted adsorption of safaranin O by tin sulfide nanoparticle loaded on activated carbon

Science.gov (United States)

Roosta, M.; Ghaedi, M.; Daneshfar, A.; Sahraei, R.

2014-03-01

In this research, the adsorption rate of safranine O (SO) onto tin sulfide nanoparticle loaded on activated carbon (SnS-NPAC) was accelerated by the ultrasound. SnS-NP-AC was characterized by different techniques such as SEM, XRD and UV-Vis measurements. The present results confirm that the ultrasound assisted adsorption method has remarkable ability to improve the adsorption efficiency. The influence of parameters such as the sonication time, adsorbent dosage, pH and initial SO concentration was examined and evaluated by central composite design (CCD) combined with response surface methodology (RSM) and desirability function (DF). Conducting adsorption experiments at optimal conditions set as 4 min of sonication time, 0.024 g of adsorbent, pH 7 and 18 mg L-1 SO make admit to achieve high removal percentage (98%) and high adsorption capacity (50.25 mg g-1). A good agreement between experimental and predicted data in this study was observed. The experimental equilibrium data fitting to Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show that the Langmuir model is a good and suitable model for evaluation and the actual behavior of adsorption. Kinetic evaluation of experimental data showed that the adsorption processes followed well pseudo-second-order and intraparticle diffusion models.

Modeling studies: Adsorption of aniline blue by using Prosopis Juliflora carbon/Ca/alginate polymer composite beads.

Science.gov (United States)

Kumar, M; Tamilarasan, R

2013-02-15

The research article describes the experimental and modeling study for the adsorptive removal of aniline blue dye (AB dye) from aqueous matrices using a Prosopis Juliflora modified carbon/Ca/alginate polymer bead as a low cost and eco-friendly adsorbent. The rate of adsorption was investigated under various experimental parameters such as contact time, adsorbent dose, dye concentration, pH and temperature. The kinetics, equilibrium and thermodynamic studies were assessed to find out the efficiency of the adsorption process. The equilibrium uptake capacity of the adsorption process was found with Freundlich and Langmuir adsorption isotherm equations and it was evaluated by dimensionless separation factor (R(L)). The dynamics of adsorption was predicted by pseudo-first order, pseudo-second order Lagergren's equation and intra particle diffusion model. Adsorption feasibility was assessed with thermodynamic parameters such as isosteric heat of adsorption (ΔH°), standard entropy (ΔS°) and Gibbs free energy (ΔG°) using VantHoff plot. The alginate bead was characterized with FTIR spectroscopy and Scanning Electron Microscopy (SEM). Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Dynamics of arsenic adsorption in the targeted arsenic-safe aquifers in Matlab, south-eastern Bangladesh: Insight from experimental studies

Energy Technology Data Exchange (ETDEWEB)

Robinson, Clare, E-mail: crobinson@eng.uwo.ca [Department of Civil and Environmental Engineering, University of Western Ontario, London, N6A 5B9 (Canada)] [NGO Forum for Drinking Water Supply and Sanitation, Lalmatia, Dhaka 1207 (Bangladesh); Broemssen, Mattias von [KTH-International Groundwater Arsenic Research Group, Department of Land and Water Resources Engineering, Royal Institute of Technology, SE-100 44 Stockholm (Sweden)] [Ramboell Sweden AB, Box 4205, SE-102 65 Stockholm (Sweden); Bhattacharya, Prosun; Haeller, Sara; Biven, Annelie [KTH-International Groundwater Arsenic Research Group, Department of Land and Water Resources Engineering, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Hossain, Mohammed [NGO Forum for Drinking Water Supply and Sanitation, Lalmatia, Dhaka 1207 (Bangladesh)] [KTH-International Groundwater Arsenic Research Group, Department of Land and Water Resources Engineering, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Jacks, Gunnar [KTH-International Groundwater Arsenic Research Group, Department of Land and Water Resources Engineering, Royal Institute of Technology, SE-100 44 Stockholm (Sweden); Ahmed, Kazi Matin; Hasan, M. Aziz [Department of Geology, University of Dhaka, Dhaka 1000 (Bangladesh); Thunvik, Roger [KTH-International Groundwater Arsenic Research Group, Department of Land and Water Resources Engineering, Royal Institute of Technology, SE-100 44 Stockholm (Sweden)

2011-04-15

Research highlights: {yields} Adsorption behaviour of shallow oxidized sediments from Matlab Region in SE Bangladesh is investigated. {yields} Oxidized sediments have a high capacity to adsorb arsenic. {yields} Adsorption capacity will be reduced by high concentration of reactive organic C. {yields} Monitoring of groundwater quality over 5 year period shows relatively stable water chemistry. - Abstract: Targeting shallow low-As aquifers based on sediment colour may be a viable solution for supplying As-safe drinking water to rural communities in some regions of Bangladesh and West Bengal in India. The sustainability of this solution with regard to the long-term risk of As-safe oxidized aquifers becoming enriched with As needs to be assessed. This study focuses on the adsorption behaviour of shallow oxidized sediments from Matlab Region, Bangladesh, and their capacity to attenuate As if cross-contamination of the oxidized aquifers occurs. Water quality analyses of samples collected from 20 tube-wells in the region indicate that while there may be some seasonal variability, the groundwater chemistry in the reduced and oxidized aquifers was relatively stable from 2004 to 2009. Although sediment extractions indicate a relatively low amount of As in the oxidized sediments, below 2.5 mg kg{sup -1}, batch isotherm experiments show that the sediments have a high capacity to adsorb As. Simulations using a surface complexation model that considers adsorption to amorphous Fe(III) oxide minerals only, under-predict the experimental isotherms. This suggests that a large proportion of the adsorption sites in the oxidized sediments may be associated with crystalline Fe(III) oxides, Mn(IV) and Al(III) oxides, and clay minerals. Replicate breakthrough column experiments conducted with lactose added to the influent solution demonstrate that the high adsorption capacity of the oxidized sediments may be reduced if water drawn down into the oxidized aquifers contains high levels of

Experimental Study On Thermal Wave Type Adsorption Refrigeration System Working On A Pair Of Activated Carbon And Methanol

Directory of Open Access Journals (Sweden)

Grzebielec Andrzej

2015-12-01

Full Text Available The aim of the study was to examine the efficiency of the thermal wave type adsorption refrigerating equipment working on a pair of activated carbon and methanol. Adsorption units can work in trigeneration systems and in applications driven by waste heat. They can be built also as a part of hybrid sorption-compressor systems, and they are very popular in solar refrigeration systems and energy storage units. The device examined in this study operates in a special mode called thermal wave. This mode allows to achieve higher efficiency rates than the normal mode of operation, as a significant contributor to transport heat from one to the other adsorber. To carry out the experiment a test bench was built, consisting of two cylindrical adsorbers filled with activated carbon, condenser, evaporator, oil heater and two oil coolers. Thermal oil circulation was responsible for providing and receiving heat from adsorbers. In order to perform the correct action a special control algorithm device was developed and implemented to keep the temperature in the evaporator at a preset level. The experimental results show the operating parameters changes in both adsorbers. Obtained COP (coefficient of performance for the cycle was 0.13.

Studies of surface adsorption on LiAlO2

International Nuclear Information System (INIS)

Fischer, A.K.; Johnson, C.E.; McDaniel, J.A.

1986-01-01

Computational and experimental approaches are being taken to understanding surface adsorption/desorption effects on tritium inventory and release. The computational survey integrates a thermodynamic treatment of surface adsorption and bulk phase effects such as solubility and gas phase composition. The system T 2 O:T 2 :LiAlO 2 was examined. The calculations indicate that surface adsorption can be expected to contribute most to tritium inventory under the conditions of lower temperatures and higher oxygen activities. Higher temperature and lower oxygen activity favor lower surface inventory. In the experimental work, a high temperature gas chromatograph was constructed in order to measure the H 2 O:H 2 surface adsorption isotherms and the solubility of hydroxide in LiAlO 2 . Preliminary data indicate that at 478 K approximately 15% of the surface is coverred for a partial pressure of H 2 O of approximately 52 Pa. Calculated values can be obtained that are in reasonable agreement with this. (orig.)

Studies of surface adsorption on LiAlO2

International Nuclear Information System (INIS)

Fischer, A.K.; McDaniel, J.A.; Johnson, C.E.

1986-01-01

Computational and experimental approaches are being taken to understanding surface adsorption/desorption effects on tritium inventory and release. The computational survey integrates a thermodynamic treatment of surface adsorption and bulk phase effects such as solubility and gas phase composition. The system T 2 O:T 2 :LiAlO 2 was examined. The calculations indicate that surface adsorption can be expected to contribute most to tritium inventory under the conditions of lower temperatures and higher oxygen activities. Higher temperature and lower oxygen activity favor lower surface inventory. In the experimental work, a high temperature gas chromatograph was constructed in order to measure the H 2 O:H 2 surface adsorption isotherms and the solubility of hydroxide in LiAlO 2 . Preliminary data indicate that at 478K approximately 15% of the surface is covered for a partial pressure of H 2 O of approximately 52 Pa. Calculated values can be obtained that are in reasonable agreement with this

Study of cesium and strontium adsorption on slovak bentonite

International Nuclear Information System (INIS)

Galambos, M.

2010-01-01

Bentonite is a natural clay and one of the most promising candidates for use as a buffer material in the geological disposal systems for high-level radioactive waste and spent nuclear fuel. It is intended to isolate metal canisters with highly radioactive waste products from the surrounding rocks because of its ability to retard the movement of radionuclides by adsorption. Slovak Republic avails of many significant deposits of bentonite. Adsorption of Cs and Sr on five Slovak bentonite of deposits (Jelsovy potok, Kopernica, Lieskovec, Lastovce and Dolna Ves) and montmorillonite K10 (Sigma-Aldrich) has been studied with the using batch of radiometric techniques. Natural, irradiated and natrified samples, in three different kinds of grain size: 15, 45 and 250 μm have been used in the experiments. The adsorptions of Cs and Sr on bentonite under various experimental conditions, such as contact time, adsorbent and adsorbate concentrations, pH after adsorption and effect of pH change, chemical modification, competitive ions and organic agents on the adsorption have been studied. The K d have been determined for adsorbent-Cs/Sr solution system as a function of contact time and adsorbate and adsorbent concentration. The data have been interpreted in terms of Langmuir isotherm. The adsorption of Cs and Sr has increased with increasing metal concentrations. Adsorption of Cs and Sr has been suppressed by presence of organic agents; and of bivalent cations more than univalent cations. By adsorption on natrified samples colloidal particles and pH value increase have been formed. Adsorption experiments carried out show that the most suitable materials intended for use as barriers surrounding a canister of spent nuclear fuel are bentonite of the Jelsovy potok and Kopernica deposits. (author)

Equilibrium, kinetic and thermodynamic studies of adsorption of Th(IV) from aqueous solution onto kaolin

International Nuclear Information System (INIS)

Hongxia Zhang; Zhiwei Niu; Zhi Liu; Zhaodong Wen; Weiping Li; Xiaoyun Wang; Wangsuo Wu

2015-01-01

The kinetics and thermodynamics of the adsorption of Th(IV) on the kaolin were studied by using batch method. In addition, the experimental data were studied by dynamic and thermodynamic models. The results showed that the adsorption capacity of the adsorbent increased with increasing temperature and solid liquid ratio, but decreased with increasing initial Th(IV) ion concentration, and the best fit was obtained for the pseudo-second-order kinetics model. The calculated activation energy for adsorption was about 45 kJ/mol, which indicated the adsorption process to be chemisorption. The adsorption isotherm data could be well described by the Langmuir as well as Dubinin-Radushkevich model. The mean free energy (E) of adsorption was calculated to be about 15 kJ/mol. The thermodynamic data calculated showed that the adsorption was spontaneous and enhanced at higher temperature. Considering kinetics and equilibrium studies, the adsorption on the sites was the rate-limiting step and that adsorption was mainly a chemisorption process through cation exchange. (author)

Experimental determination of fission gas adsorption coefficients

International Nuclear Information System (INIS)

Lovell, R.; Underhill, D.W.

1979-01-01

Large charcoal beds have been used for a number of years for the holdup and decay of radioactive isotopes of krypton and xenon. Reliable design of these beds depends on an accurate knowledge of the adsorption coefficient of krypton and xenon on the adsorbents used in these beds. It is somewhat surprising that there is no standard procedure of determining the adsorption coefficient for krypton and xenon. Fundamental information needed to establish a standardized reproducible test procedure is given emphasizing the breakthrough curves commonly used to analyze dynamic adsorption data can lead to serious systematic errors and the fact that the adsorption coefficient, if calculated from the arithmetic holding time, is independent of geometric factors such as the shape of the adsorption bed and the irregular shape of the adsorbent

A batch adsorption study on bentonite clay Pertinence to transport modeling?

Science.gov (United States)

BOURG, I.; BOURG, A. C.; SPOSITO, G.

2001-12-01

Bentonite clay is often used as a component of engineered barriers for the isolation of high-level toxic wastes. This swelling clay is used for its physical (impermeability, self-healing) but also for its chemical properties, mostly a high cation exchange capacity (CEC). The adsorbed cations being temporarily immobilized, this should slow down the release of cations from the waste to the surrounding environment. In order to assess the performance of the engineered barrier, the partitioning of solutes between the liquid and solid phases needs to be quantified for use in transport models. The usual method for characterizing the adsorption is through batch adsorption experiments on dispersed suspensions of the solid, yielding an adsorption isotherm (adsorbed concentration vs. dissolved concentration). This isotherm however should be a function of various environmental variables (e.g., pH, ionic strength, concentrations of various ligands and competing adsorbents), so that extrapolation of lab data to performance assessment in the field is problematic. We present results from a study of the adsorption of cesium, strontium, cadmium and lead on dispersed suspensions of the standard BX-80 bentonite. Through a wide range of experimental parameters (pH, ionic strength, reaction time, reactor open or closed to the atmosphere, study of a range of cations of differing properties), we seek a mechanistic interpretation of the results instead of an empirical determination of adsorption parameters. Depending on the mechanisms that control the adsorption in different experimental ranges, we discuss the degree to which the partitioning coefficient (Kd) obtained in the lab can be extrapolated to a transport model through compacted bentonite in a natural environment.

Adsorptive removal of Auramine-O: Kinetic and equilibrium study

International Nuclear Information System (INIS)

Mall, Indra Deo; Srivastava, Vimal Chandra; Agarwal, Nitin Kumar

2007-01-01

Present study deals with the adsorption of Auramine-O (AO) dye by bagasse fly ash (BFA) and activated carbon-commercial grade (ACC) and laboratory grade (ACL). BFA is a solid waste obtained from the particulate collection equipment attached to the flue gas line of the bagasse fired boilers of cane sugar mills. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH 0 ), contact time, adsorbent dose and initial concentration (C 0 ) for the removal of AO. Optimum conditions for AO removal were found to be pH 0 ∼ 7.0 and equilibrium time ∼30 min for BFA and ∼120 min for activated carbons. Optimum BFA, ACC and ACL dosages were found to be 1, 20 and 2 g/l, respectively. Adsorption of AO followed pseudo-second order kinetics with the initial sorption rate for adsorption on BFA being the highest followed by those on ACL and ACC. The sorption process was found to be controlled by both film and pore diffusion with film diffusion at the earlier stages followed by pore diffusion at the later stages. Equilibrium isotherms for the adsorption of AO on BFA, ACC and ACL were analyzed by Freundlich, Langmuir, Dubinin-Radushkevich, and Temkin isotherm equations using linear correlation coefficient. Langmuir isotherm gave the best correlation of adsorption for all the adsorbents studied. Thermodynamic study showed that adsorption of AO on ACC (with a more negative Gibbs free energy value) is more favoured. BFA which was used without any pretreatment showed high surface area, pore volume and pore size exhibiting its potential to be used as an adsorbent for the removal of AO

The Study of Cr3+ Adsorption Wukirsari Pumice

International Nuclear Information System (INIS)

Samin; Susanna TS

2002-01-01

As an alternative to solve an environmental problem of Cr 3+ , the use of Wukirsari pumice has been studied. Before used as an adsorbent. 100-200 mesh of Wukirsari pumice was washed and calcinate. The elements composition of adsorbent was analyzed using Atomic Adsorption Spectrophotometer (AAS) method and presented as their oxides. After calcination, the pumice was saturated by NaCI and then converted to its ceramic. The mineral composition of pumice and its ceramic was determined using XRD method. Experimental results show optimum temperature for calcination was 500 o C and 5 hours duration of contact time was found from adsorption of Na + , with the value of 505 mg/g pumice. The other results show that pH of the solution influence the adsorption. The ion exchange between Na + and Cr 3+ did not follow ideal solution, and one ion Cr 3+ could replace only one ion Na + hence optimum adsorption of Cr 3+ was 1141.47 mg/g pumice. The data XRD shows that mineral composition of the pumice was magnetite, anorthite, and montmorilonite, while composition of its ceramic was feldspar and cristobalite. (author)

Adsorption of gas mixtures on heterogeneous solid surfaces

Energy Technology Data Exchange (ETDEWEB)

Jaroniec, M; Rudzinski, W

1977-01-01

A review of theoretical studies on the physical adsorption from gas mixtures on heterogeneous solid surfaces, mainly by Jaroniec and coworkers, covers the vector notation used in the calculations; adsorption isotherms for multicomponent gases; the generalized integral equation for adsorption of gas mixtures, its numerical and analytical solutions, applied, (e.g., to interpret the experimental adsorption isotherms of ethane/ethylene on Nuxit-AL); thermodynamic relations, applied, (e.g., to calculating isosteric adsorption heats from experimental parameters for the adsorption of propylene from propane/propylene mixtures on Nuxit-AL); and the derivation and use of a simplified integral equation for describing the adsorption from gas mixtures on heterogeneous surfaces. 75 references.

Adsorption of CO2 on amine-functionalised MCM-41: experimental and theoretical studies.

Science.gov (United States)

dos Santos, Thiago Custódio; Bourrelly, Sandrine; Llewellyn, Philip L; Carneiro, José Walkimar de M; Ronconi, Célia Machado

2015-04-28

Adsorption of CO2 on MCM-41 functionalised with [3-(2-aminoethylamino)propyl]trimethoxysilane (MCM-41-N2), N(1)-(3-trimethoxysilylpropyl)diethylenetriamine (MCM-41-N3), 4-aminopyridine (MCM-41-aminopyridine), 4-(methylamino)pyridine (MCM-41-methylaminopyridine) and 1,5,7-triazabicyclo[4.4.0]dec-5-ene (MCM-41-guanidine) was investigated. The amine-functionalised materials were characterised by (29)Si and (13)C solid-state nuclear magnetic resonance, N2 adsorption/desorption isotherms, X-ray diffraction and transmission electron microscopy. CO2 adsorption at 1.0 bar and 30 °C showed that the amount of CO2 (nads/mmol g(-1)) adsorbed on MCM-41-N2 and MCM-41-N3 is approximately twice the amount adsorbed on MCM-41. For MCM-41-aminopyridine, MCM-41-methylaminopyridine and MCM-41-guanidine, the CO2 adsorption capacity was smaller than that of MCM-41 at the same conditions. The proton affinity (computed with wB97x-D/6-311++G(d,p)) of the secondary amino groups is higher than that of the primary amino groups; however, the relative stabilities of the primary and secondary carbamates are similar. The differential heat of adsorption decreases as the number of secondary amino groups increases.

Study of algae's adsorption to uranium ion in water solution

International Nuclear Information System (INIS)

Du Yang; Qiu Yongmei; Dan Guiping; Zhang Dong; Lei Jiarong

2007-01-01

The adsorption efficiencies of the algae to uranium ion were determined at various pH, uranium ion concentrations, adsorption temperatures and the species of coexisted metal ions, and the effect of coexisted metal ion on the adsorption efficiency was researched. The experimental results at pH= 5-8 are as follows. 1) the adsorption capacity is a constant to be about 1.40 μg/g for the Yantai red alga and the sea spinach, and is changeable in the range of 1.03-2.23 μg/g with pH for the sea edible fungus; 2) for the algae the adsorption efficiency and adsorption capacity are related to uranium ion concentration, and the maximum adsorption efficiency and capacity is 95.8% and 65.4 μg/g, respectively; 3) the adsorption process for 24 h is not dependent on the temperature; 4) the effect of the species of coexisted metal ions on the adsorption capacity of uranium ion is various with the time during adsorption process. (authors)

Experimental research on novel adsorption chiller driven by low grade heat source

International Nuclear Information System (INIS)

Wang, D.C.; Shi, Z.X.; Yang, Q.R.; Tian, X.L.; Zhang, J.C.; Wu, J.Y.

2007-01-01

A novel silica gel-water adsorption chiller is developed. This chiller consists of three vacuum chambers: two adsorption/desorption (or evaporation/condensation) vacuum chambers and one heat pipe working vacuum chamber. In this chiller, only one vacuum valve is installed between the two adsorption/desorption vacuum chambers to improve its performance when it is driven by a low temperature heat source. The operational reliability of the chiller is highly improved because of fewer moving parts. In this work, the performance of the chiller is experimentally tested under a low grade heat source, such as 55-67 o C. The test results show that the performance of this chiller is satisfying when it is driven by a low grade heat source, such as 65 o C, and the cooling capacity (or refrigeration capacity) will reach about 5 kW when the hot water temperature is 65 o C, the cooling water temperature is 30.5 o C and the chilled water inlet temperature is 15.1 o C. The test results confirm that this kind of adsorption chiller can be effectively driven by a low grade heat source

A Simple Adsorption Experiment

Science.gov (United States)

Guirado, Gonzalo; Ayllon, Jose A.

2011-01-01

The study of adsorption phenomenon is one of the most relevant and traditional physical chemistry experiments performed by chemistry undergraduate students in laboratory courses. In this article, we describe an easy, inexpensive, and straightforward way to experimentally determine adsorption isotherms using pieces of filter paper as the adsorbent…

Fundamentals of high pressure adsorption

Energy Technology Data Exchange (ETDEWEB)

Zhou, Y.P.; Zhou, L. [Tianjin University, Tianjin (China). High Pressure Adsorption Laboratory

2009-12-15

High-pressure adsorption attracts research interests following the world's attention to alternative fuels, and it exerts essential effect on the study of hydrogen/methane storage and the development of novel materials addressing to the storage. However, theoretical puzzles in high-pressure adsorption hindered the progress of application studies. Therefore, the present paper addresses the major theoretical problems that challenged researchers: i.e., how to model the isotherms with maximum observed in high-pressure adsorption; what is the adsorption mechanism at high pressures; how do we determine the quantity of absolute adsorption based on experimental data. Ideology and methods to tackle these problems are elucidated, which lead to new insights into the nature of high-pressure adsorption and progress in application studies, for example, in modeling multicomponent adsorption, hydrogen storage, natural gas storage, and coalbed methane enrichment, was achieved.

Equilibrium and kinetic study for the adsorption of p-nitrophenol from wastewater using olive cake based activated carbon

International Nuclear Information System (INIS)

Abdel-Ghani, N. T.; Rawash, E. S. A.; El-Chaghaby, G. A.

2016-01-01

The present work was carried out to evaluate the removal of p-nitrophenol by adsorption onto olive cake based activated carbon having a BET surface area of 672 m²/g. The batch adsorption experimental results indicated that the equilibrium time for nitrophenol adsorption by olive cake-based activated carbon was 120 minutes. The adsorption data was modeled by equilibrium and kinetic models. The pseudo- first and second order as well as the Elovichkinetic models were applied to fit the experimental data and the intra particle diffusion model was assessed for describing the mechanism of adsorption. The data were found to be best fitted to the pseudo-second order model with a correlation coefficient (R2=0.986). The intra particle diffusion mechanism also showed a good fit to the experimental data, showing two distinct linear parts assuming that more than one step could be involved in the adsorption of nitrophenol by the activated carbon. The equilibrium study was performed using three models including Langmuir, Freundlich and Temkin. The results revealed that the Temkin equilibrium model is the best model fitting the experimental data (R2=0.944). The results of the present study proved the efficiency of using olive cake based activated carbon as a novel adsorbent for the removal of nitrophenol from aqueous solution.

Kinetic and equilibrium study of adsorption of di-azo dyes on commercial activated carbon

International Nuclear Information System (INIS)

Hyali, E.A.S.A.; Abady, T.G.A.

2013-01-01

This research work is concerned with studying the adsorption of a number of di-azo dyes on commercial activated carbon (CAC). The synthesized dyes vary in their structures by the central parts. which are either ortho, meta or para phenvlene diamine. This variation affects the linearity of molecules, their spatial arrangement and electron movement throughout the molecule by resonance. Factors a fleeting adsorption process, such as the efiect of contact time, initial concentration, p1-I of the adsorption medium, adsorbent dose, effect of solvent and temperature were studied. The results indicated that, the adsorption process is fast in the first 10 mm, then gradually decreased with time and approaches maximum within 70-80 min for all the studied dyes. The increase of initial concentration and temperature decreased the adsorption efficiency. The results also shows that, the adsorption is found to be more efficient at low Ph value. The increase of the adsorbent dose increases the adsorption efficiency and decreases its capacity. The variation of solvent (ethanol-water ratio) indicates that the decrease of dielectric constant lowers the adsorption efficiency. The study included application of three adsorption isotherms, Freundlich, Langmuir and Tempkin on the experimental data of the studied systems. The results indicated that, Freundlich isotherm fits better the adsorption data. Kinetic analysis of the adsorption data was also conducted by employing 4 kinetic models; pseudo first order and pseudo second order, Elovich and intra particle diffusion equations. The results obtained conclude that, the studied systems follow the Pseudo second order model. (author)

Adsorption of petroleum resins and asphaltenes onto reservoir rock sands studied by near infrared (NIR) spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Syunyaev, R.Z.; Balabin, R.M. [Russian State Univ. of Oil and Gas, Moscow (Russian Federation). Dept. of Physics; Akhatov, I.S. [North Dakota State Univ., Fargo, ND (United States). Dept. of Mechanical Engineering and Center for Nanoscale Science and Engineering

2008-07-01

The presence of asphaltene and resin in crude oil is known to cause well bore plugging and pipeline deposition; stabilization of water/oil emulsions; sedimentation and plugging during crude oil storage; adsorption on refining equipment and coke formation. Kinetic and thermodynamic parameters of adsorption are also known to influence wettability and the capillary number. In this study, adsorption parameters of petroleum resins and asphaltenes were evaluated by Near Infrared (NIR) spectroscopy. Fractioned quartz, dolomite, mica and kaolinite sands were used as adsorbent. The particle size distribution was evaluated using an optical microscope. Porosity and permeability of each fraction were designed and benzene was used as the solvent. Various approaches for calibrating NIR spectra-macromolecules concentration were discussed. In this study, the partial least squares (PLS) regression method was used and the Langmuir model was chosen for experimental data fitting. Kinetic and isothermic data was used to evaluate the maximal adsorbed mass density, the equilibrium constant of adsorption, and the rate constants of adsorption and desorption. The rate constants of resins adsorption and desorption depended on the concentration. A numerical algorithm was developed to estimate the diffusion coefficient and relaxation time from the experimental data.

Adsorptive removal of phthalate ester (Di-ethyl phthalate) from aqueous phase by activated carbon: a kinetic study.

Science.gov (United States)

Venkata Mohan, S; Shailaja, S; Rama Krishna, M; Sarma, P N

2007-07-19

Adsorptive studies were carried out on Di-ethyl phthalate (DEP) removal from aqueous phase onto activated carbon. Batch sorption studies were performed and the results revealed that activated carbon demonstrated ability to adsorb DEP. Influence of varying experimental conditions such as DEP concentration, pH of aqueous solution, and dosage of adsorbent were investigated on the adsorption process. Sorption interaction of DEP onto activated carbon obeyed the pseudo second order rate equation. Experimental data showed good fit with both the Langmuir and Freundlich adsorption isotherm models. DEP sorption was found to be dependent on the aqueous phase pH and the uptake was observed to be greater at acidic pH.

Stepwise adsorption of phenanthrene at the fly ash-water interface as affected by solution chemistry: experimental and modeling studies.

Science.gov (United States)

An, Chunjiang; Huang, Guohe

2012-11-20

Fly ash (FA) is predominantly generated from coal-fired power plants. Contamination during disposal of FA can cause significant environmental problems. Knowledge about the interaction of FA and hydrophobic organic pollutants in the environment is very limited. This study investigated the adsorption of phenanthrene at the interface of FA and water. The performance of phenanthrene adsorption on FA and the effects of various aqueous chemistry conditions were evaluated. The adsorption isotherms exhibited an increasing trend in the adsorbed amounts of phenanthrene, while a stepwise pattern was apparent. A stepwise multisite Langmuir model was developed to simulate the stepwise adsorption process. The adsorption of phenanthrene onto FA was noted to be spontaneous at all temperatures. The thermodynamic results indicated that the adsorption was an exothermic process. The adsorption capacity gradually decreased as pH increased from 4 to 8; however, this trend became less significant when pH was changed from 8 to 10. The binding affinity of phenanthrene to FA increased after the addition of humic acid (HA). The pH variation was also responsible for the changes of phenanthrene adsorption on FA in the presence of HA. High ionic strength corresponded to low mobility of phenanthrene in the FA-water system. Results of this study can help reveal the migration patterns of organic contaminants in the FA-water system and facilitate environmental risk assessment at FA disposal sites.

Adsorption of simple molecules on clean metal surfaces

International Nuclear Information System (INIS)

Na Lamphun, O.-A.

1980-06-01

The adsorption of nitric oxide, oxygen, krypton and xenon on evaporated tungsten, nickel and iron films is studied. The theoretical and experimental aspects of adsorption are reviewed, a preliminary study of adsorption by the volumetric method is presented, surface potential and sticking probability studies of adsorption using ion gauges are investigated and an analysis of residual gases, sticking probability and surface potential studies using quadrupole mass spectrometry, given. (author)

Adsorption of guanidinium collectors on aluminosilicate minerals - a density functional study.

Science.gov (United States)

Nulakani, Naga Venkateswara Rao; Baskar, Prathab; Patra, Abhay Shankar; Subramanian, Venkatesan

2015-10-07

In this density functional theory based investigation, we have modelled and studied the adsorption behaviour of guanidinium cations and substituted (phenyl, methoxy phenyl, nitro phenyl and di-nitro phenyl) guanidinium cationic collectors on the basal surfaces of kaolinite and goethite. The adsorption behaviour is assessed in three different media, such as gas, explicit water and pH medium, to understand the affinity of GC collectors to the SiO4 tetrahedral and AlO6 octahedral surfaces of kaolinite. The tetrahedral siloxane surface possesses a larger binding affinity to GC collectors than the octahedral sites due to the presence of surface exposed oxygen atoms that are active in the intermolecular interactions. Furthermore, the inductive electronic effects of substituted guanidinium cations also play a key role in the adsorption mechanism. Highly positive cations result in a stronger electrostatic interaction and preferential adsorption with the kaolinite surfaces than low positive cations. Computed interaction energies and electron densities at the bond critical points suggest that the adsorption of guanidinium cations on the surfaces of kaolinite and goethite is due to the formation of intra/inter hydrogen bonding networks. Also, the electrostatic interaction favours the high adsorption ability of GC collectors in the pH medium than gas phase and water medium. The structures and energies of GC collectors pave an intuitive view for future experimental studies on mineral flotation.

Study on the adsorption of H2O and CO2 from the carrier gas of high-temperature gas-cooled reactor

International Nuclear Information System (INIS)

Liao Cuiping; Zheng Zhenhong; Shi Fuen; Zhou Dasen

1998-01-01

The author is focused on the experimental studies of the adsorption of moisture and carbon dioxide from the carrier gas of high-temperature gas-cooled reactor (HTGR). A suitable adsorbent--5A type molecular sieve spherical particles with an average diameter of 3 mm is chosen to purify the carrier gas with impurities of moisture and carbon dioxide. Experimental data at different concentration, flow rate, adsorptive temperature, pressure and bed depth are obtained from isothermal adsorption tests in order to examine the effects of these parameters on adsorption dynamic and for the optimal parameters selection of adsorption process. Experimental breakthrough curves, dynamic single component and multicomponent adsorption curves are obtained. The outlet concentration of H 2 O and CO 2 can reach below 1.0 x 10 -5 , so this purification system can meet the demands of HTGR

Adsorption of butyl acetate in air over silver-loaded Y and ZSM-5 zeolites: experimental and modelling studies.

Science.gov (United States)

Bhatia, Subhash; Abdullah, Ahmad Zuhairi; Wong, Cheng Teng

2009-04-15

Adsorption behaviours of butyl acetate in air have been studied over silver-loaded Y (Si/Al=40) and ZSM-5 (Si/Al=140) zeolites. The silver metal was loaded into the zeolites by ion exchange (IE) and impregnation (IM) methods. The adsorption study was mainly conducted at a gas hourly space velocity (GHSV) of 13,000 h(-1) with the organic concentration of 1000 ppm while the desorption step was carried out at a GHSV of 5000 h(-1). The impregnated silver-loaded adsorbents showed lower uptake capacity and shorter breakthrough time by about 10 min, attributed to changes in the pore characteristics and available surface for adsorption. Silver exchanged Y (AgY(IE)) with lower hydrophobicity showed higher uptake capacity of up to 35%, longer adsorbent service time and easier desorption compared to AgZSM-5(IE). The presence of water vapour in the feed suppressed the butyl acetate adsorption of AgY(IE) by 42% due to the competitive adsorption of water on the surface and the effect was more pronounced at lower GHSV. Conversely, the adsorption capacity of AgZSM-5(IE) was minimally affected, attributed to the higher hydrophobicity of the material. A mathematical model is proposed to simulate the adsorption behaviour of butyl acetate over AgY(IE) and AgZSM-5(IE). The model parameters were successfully evaluated and used to accurately predict the breakthrough curves under various process conditions with root square mean errors of between 0.05 and 0.07.

Adsorption of trace elements on a bentonite sample: experimental study and modelling; Retention d'elements trace sur une bentonite: etude experimentale et modelisation

Energy Technology Data Exchange (ETDEWEB)

Hurel, Ch

2002-12-15

Radioactive waste storage in deep underground is studied in France. The alteration of the radioactive waste can mobilize the elements that can migrate to the geosphere. Clays (bentonite) are investigated as major materials constituting the barriers because of their low permeability and high retention capacity. A thermodynamic surface complexation model, based on the component additivity principle was investigated, in order to predict the adsorption behaviour of pollutants in contact with clay. This principle allows an independent determination of each parameter of the model, limiting the fitting procedure of correlated data, and it allows the use of an adsorption thermodynamic database for a solid. The predictions obtained were in good accordance with experimental data. The model could then be applied successfully in performance assessment. (author)

Adsorption of polyvinylalcohol on paraffin-water interfaces and the properties of paraffin-in-water emulsions stabilized by polyvinylalcohol : an experimental study

NARCIS (Netherlands)

Lankveld, J.M.G.

1970-01-01

The adsorption of polyvinylalcohol (PVA) on the paraffin-water interface has been studied by interfacial tension measurements and by direct measurement of the adsorption with emulsions. The aim of the study was to provide more insight into the factors which influence the adsorption of polymers

Comparative Study on Adsorption of Mn(II from Aqueous Solutions on Various Activated Carbons

Directory of Open Access Journals (Sweden)

K. A. Emmanuel

2009-01-01

Full Text Available The adsorption of Mn(II on indigenously prepared activated carbons (IPAC from Bombax malabaricum, Pithecelobium dulse, Ipomea batatas and Peltaforum ferraginium have been studied. The effects of various experimental parameters have been investigated using batch adsorption technique. The extent of Mn(II removal increased with decrease in initial concentration of the Mn(II, particle size of the adsorbent and increased with increase in contact time, amount of adsorbent used and the initial pH of the solution. Adsorption data were modeled using Freundlich and Langmuir adsorption isotherms and first order kinetic equations. The kinetics of adsorption was found to be first order with regard to intra-particle diffusion rate. The results indicate that such carbons could be employed as low cost adsorbents in waste water treatment for the removal of Mn(II.

A new apparatus for the determination of adsorption isotherms and adsorption enthalpies on microporous and meso-porous media

International Nuclear Information System (INIS)

Mouahid, A.

2010-01-01

A specific thermostated experimental device comprising a differential heat flow calorimeter coupled with a home built manometric system has been built for the simultaneous determination of adsorption isotherms and adsorption enthalpies. The differential heat flow calorimeter is a Tian Calvet Setaram C80 model which measures the heat flux of a gas and can be operated isothermally, the manometric system is a stainless steel homemade apparatus. This coupled apparatus allows measurements for pressure up to 2.5 MPa and temperature up to 423.15 K. On the one hand, the apparatus and the experimental procedures are described. On the second hand the reliability and reproducibility were established by measuring adsorption isotherms on a benchmark (Filtrasorb F400) at 318.15 K. The gravimetric method has been used at higher pressure at various temperatures. These devices allowed us to study the adsorption of supercritical fluid (nitrogen N 2 , methane CH 4 , carbon dioxide CO 2 ) in activated carbons and microporous or meso-porous silica. The adsorption of methane on a rock of type (TGR) was also studied. These experimental results are used for the study of the interactions fluid / solid that must be taken into account in molecular simulations or DFT theory. (author)

Kinetic studies of uranyl ion adsorption on acrylonitrile (AN)/polyethylene glycol (PEG) interpenetrating networks (IPN)

International Nuclear Information System (INIS)

Aycik, G.A.; Gurellier, R.

2004-01-01

Full text: The kinetics of the adsorption of uranyl ions on amidoximated acrylonitrile (AN)/ polyethylene glycol (PEG) interpenetrating network (IPNs) from aqueous solutions was studied as a function of time and temperature. The IPNs were prepared by irradiation initiated gamma polymerisation using Co-60 gamma source. Adsorption capacities were performed for definite uranyl ion concentrations of 1x10 -2 M and at four different temperatures as 290K, 298K, 308K and 318K by gamma spectrometer. Adsorption time was increased from zero to 48 hours. The results indicate that adsorption capacity increases linearly with increasing temperature. Temperature and agitation hardly influence equilibrium and kinetics and decreasing of temperature results in a slightly greater time to reach equilibrium. The adsorption of uranyl ions has been studied in a multi step mechanism processes thus comparing chemical sorption and diffusion sorption processes. The experimental data was analysed using various kinetic models to determine the best-fit equation for the adsorption mechanisms. However, it was shown that all models, in general according to the reaction time and uranyl ion concentration in the solution, could describe the adsorption of uranyl ion onto amidoximated IPN, the adsorption kinetics was best described by zeroth order and intraparticle diffusion model whereas that of in increasing time by pseudo first and pseudo second order response respectively. External-intraparticle diffusion and zeroth order process in the IPN structure is proposed as a mass transfer mechanism and the results indicate a diffusion-controlled process. The Mean Activation Energy Of Uranyl Ions Adsorption Was Found As 4,1 Kj/Mole By Using Arrhenius Equation. The Rate Constant, The Equilibrium Adsorption Capacity And The Initial Adsorption Rate Were Calculated For All Models At Each Temperature. Kinetic Parameters Of All Models And The Normalized Standard Deviations Between The Measured And Predicted

Experimental investigation and modeling of adsorption of water and ethanol on cornmeal in an ethanol-water binary vapor system

Energy Technology Data Exchange (ETDEWEB)

Chang, H.; Yuan, X.G.; Tian, H.; Zeng, A.W. [State Key Laboratory of Chemical Engineering, Tianjin University, Tianjin 300072 (China)

2006-04-15

The adsorption capacity of water and ethanol on cornmeal in an ethanol-water binary vapor system was investigated in a fixed-bed apparatus for ethanol dehydration. Experiments were performed at temperatures of 82-100 C for different relative humidities of ethanol-water vapor. Adsorption equilibrium models, including those based on the adsorption potential theory of Polanyi and Sircar's model, have been used to fit the experimental data for water adsorption on cornmeal, and all gave good fits. For ethanol adsorption, pseudo-equilibrium was defined as the mass adsorbed on the cornmeal within the time needed for the equilibrium for water on the same adsorbent. Based on this limiting condition, adsorption behaviors and mechanisms were analyzed. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Study of high-pressure adsorption from supercritical fluids by the potential theory

DEFF Research Database (Denmark)

Monsalvo, Matias Alfonso; Shapiro, Alexander

2009-01-01

The multicomponent potential theory of adsorption (MPTA), which has been previously used to study low-pressure adsorption of subcritical fluids, is extended to adsorption equilibria from supercritical fluids up to high pressures. The MPTA describes an adsorbed phase as an inhomogeneous fluid...... the adsorbed and the gas phases. We have also evaluated the performance of the classical Soave-Redlich-Kwong (SRK) EoS. The fluid-solid interactions are described by simple Dubinin-Radushkevich-Astakhov (DRA) potentials. In addition, we test the performance of the 10-4-3 Steele potential. It is shown...... that application of sPC-SAFT slightly improves the performance of the MPTA and that in spite of its simplicity, the DRA model can be considered as an accurate potential, especially, for mixture adsorption. We show that, for the sets of experimental data considered in this work, the MPTA is capable of predicting...

A density functional study on adsorption and dissociation of O 2 on Ir(1 0 0) surface

Science.gov (United States)

Erikat, I. A.; Hamad, B. A.; Khalifeh, J. M.

2011-06-01

The adsorption and the reaction barrier for the dissociation of O 2 on Ir(1 0 0) surface are studied using periodic self-consistent density functional theory (DFT) calculations. Dissociative adsorption is found to be energetically more favorable compared to molecular adsorption. Parallel approaches Prl1 and Prl2 on a hollow site with the same adsorption energy of -3.93 eV for both of them are found to have the most energetically preferred sites of adsorptions among all the studied cases. Hybridization between p-O 2 and d-metal orbitals is responsible for the dissociative adsorption. The minimum energy path is determined by using the nudge elastic band method (NEB). We found that the dissociation occurs immediately and very early in the dissociation path with a small activation barrier (0.26 eV), which means that molecular adsorption of O 2 on Ir(1 0 0) surface occurs at very low temperatures; this is consistent with previous experimental and theoretical studies on Ir surfaces.

Kinetic and thermodynamic studies on the adsorption of anionic surfactant on quaternary ammonium cationic cellulose.

Science.gov (United States)

Zhang, Yuanzhang; Shi, Wenjian; Zhou, Hualan; Fu, Xing; Chen, Xuan

2010-06-01

Removal of anionic surfactants from aqueous solutions by adsorption onto quaternary ammonium cationic cellulose (QACC) was investigated. The effects of solution acidity, initial concentration, adsorption time, and temperature on the adsorption of sodium dodecyl-benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS) were studied. The kinetic experimental data fit well with the pseudo-second-order model; the rate constant of the adsorption increased with temperature. The values of apparent activation energy for the adsorption were calculated as ranging from 10.2 to 17.4 kJ/ mol. The adsorption isotherm can be described by the Langmuir isotherm. The values of thermodynamic parameters (deltaH0, deltaS0, and deltaG0) for the adsorption indicated that this process was spontaneous and endothermic. At 318 K, the saturated adsorption capacities of QACC for SDBS, SLS, and SDS were 1.75, 1.53, and 1.39 mmol/g, respectively. The adsorption process was mainly chemisorption and partially physisorption. The results show that QACC is effective for the removal of anionic surfactants.

Adsorption of n-butane on graphene/Ru(0001)—A molecular beam scattering study

Energy Technology Data Exchange (ETDEWEB)

Sivapragasam, Nilushni; Nayakasinghe, Mindika T.; Burghaus, Uwe, E-mail: uwe.burghaus@ndsu.edu [Department of Chemistry and Biochemistry, North Dakota State University, Fargo, North Dakota 58108 (United States)

2016-07-15

Adsorption kinetics/dynamics of n-butane on graphene, physical vapor deposited on Ru(0001) (hereafter G/Ru), and bare Ru(0001) (hereafter Ru) are discussed. The chemical activity of the supported-graphene as well as the support was probed by thermal desorption spectroscopy (adsorption kinetics). In addition and to the best of our knowledge, for the first time, molecular beam scattering data of larger molecules were collected for graphene (probing the adsorption dynamics). Furthermore, samples were inspected by x-ray photoelectron spectroscopy and Auger electron spectroscopy. At the measuring conditions used here, n-butane adsorption kinetics/dynamics are molecular and nonactivated. Binding energies of butane on Ru and G/Ru are indistinguishable within experimental uncertainty. Thus, G/Ru is “kinetically transparent.” Initial adsorption probabilities, S{sub 0}, of n-butane decrease with increasing impact energy (0.76–1.72 eV) and are adsorption temperature independent for both Ru and G/Ru, again consistent with molecular adsorption. Also, S{sub 0} of Ru and G/Ru are indistinguishable within experimental uncertainty. Thus, G/Ru is “dynamically transparent.” Coverage dependent adsorption probabilities indicate precursor effects for graphene/Ru.

Adsorption of n-butane on graphene/Ru(0001)—A molecular beam scattering study

International Nuclear Information System (INIS)

Sivapragasam, Nilushni; Nayakasinghe, Mindika T.; Burghaus, Uwe

2016-01-01

Adsorption kinetics/dynamics of n-butane on graphene, physical vapor deposited on Ru(0001) (hereafter G/Ru), and bare Ru(0001) (hereafter Ru) are discussed. The chemical activity of the supported-graphene as well as the support was probed by thermal desorption spectroscopy (adsorption kinetics). In addition and to the best of our knowledge, for the first time, molecular beam scattering data of larger molecules were collected for graphene (probing the adsorption dynamics). Furthermore, samples were inspected by x-ray photoelectron spectroscopy and Auger electron spectroscopy. At the measuring conditions used here, n-butane adsorption kinetics/dynamics are molecular and nonactivated. Binding energies of butane on Ru and G/Ru are indistinguishable within experimental uncertainty. Thus, G/Ru is “kinetically transparent.” Initial adsorption probabilities, S 0 , of n-butane decrease with increasing impact energy (0.76–1.72 eV) and are adsorption temperature independent for both Ru and G/Ru, again consistent with molecular adsorption. Also, S 0 of Ru and G/Ru are indistinguishable within experimental uncertainty. Thus, G/Ru is “dynamically transparent.” Coverage dependent adsorption probabilities indicate precursor effects for graphene/Ru.

Hydrogen-Induced Adsorption of Carbon Monoxide on the Gold Dimer Cation: A Joint Experimental and DFT Investigation.

Science.gov (United States)

Vojkovic, Marin; Rayane, Driss; Antoine, Rodolphe; Broyer, Michel; Allouche, Abdul-Rahman; Mignon, Pierre; Dugourd, Philippe

2017-06-15

It is demonstrated, using tandem mass spectrometry and radio frequency ion trap, that the adsorption of a H atom on the gold dimer cation, Au 2 H + , prevents its dissociation and allows for adsorption of CO. Reaction kinetics are measured by employing a radio frequency ion trap, where Au 2 + and CO interact for a given reaction time. The effect of a hydrogen atom is evaluated by comparing reaction rate constants measured for Au 2 + and Au 2 H + . The theoretical results for the adsorption of CO molecules and their reaction characteristics with Au 2 + and Au 2 H + are found to agree with the experimental findings. The joint investigations provide insights into hydrogen atom adsorption effects and consequent reaction mechanisms.

Experimental System of Solar Adsorption Refrigeration with Concentrated Collector.

Science.gov (United States)

Yuan, Z X; Li, Y X; Du, C X

2017-10-18

To improve the performance of solar adsorption refrigeration, an experimental system with a solar concentration collector was set up and investigated. The main components of the system were the adsorbent bed, the condenser, the evaporator, the cooling sub-system, and the solar collector. In the first step of the experiment, the vapor-saturated bed was heated by the solar radiation under closed conditions, which caused the bed temperature and pressure to increase. When the bed pressure became high enough, the bed was switched to connect to the condenser, thus water vapor flowed continually from the bed to the condenser to be liquefied. Next, the bed needed to cool down after the desorption. In the solar-shielded condition, achieved by aluminum foil, the circulating water loop was opened to the bed. With the water continually circulating in the bed, the stored heat in the bed was took out and the bed pressure decreased accordingly. When the bed pressure dropped below the saturation pressure at the evaporation temperature, the valve to the evaporator was opened. A mass of water vapor rushed into the bed and was adsorbed by the zeolite material. With the massive vaporization of the water in the evaporator, the refrigeration effect was generated finally. The experimental result has revealed that both the COP (coefficient of the performance of the system) and the SCP (specific cooling power of the system) of the SAPO-34 zeolite was greater than that of the ZSM-5 zeolite, no matter whether the adsorption time was longer or shorter. The system of the SAPO-34 zeolite generated a maximum COP of 0.169.

Adsorption of Pb(II) from fish sauce using carboxylated cellulose nanocrystal: Isotherm, kinetics, and thermodynamic studies.

Science.gov (United States)

Wang, Nan; Jin, Ru-Na; Omer, A M; Ouyang, Xiao-Kun

2017-09-01

In the present study, a new adsorbent based on carboxylated cellulose nanocrystal (CCN) was developed for the adsorption of Pb(II) from fish sauce. The prepared adsorbent material was characterized by zeta potential, FT-IR, XRD, and XPS tools. The changes in the morphological structure of the developed CCN surface were evidenced by SEM and TEM. The favorable adsorption conditions were selected by studying the contact time, initial concentration, temperature, and concentration of the used glutamic acid and NaCl. The results indicated that the Langmuir isotherm model agrees very well with experimental adsorption data (R 2 =0.9962) with a maximum adsorption capacity 232.56mg/g of Pb(II) at 293.2K. Additionally, data of the adsorption kinetics follow the pseudo-second-order kinetics (R 2 >0.9990). On the other hand, the thermodynamics studies show that the adsorption process is spontaneous and endothermic. Furthermore, the developed CCN could be regenerated using acid treatment with a good reusability for Pb(II) adsorption. The results clearly indicated that the synthesized CCN could be effectively applied as a new material for Pb(II) adsorption from fish sauce solutions. Copyright © 2017 Elsevier B.V. All rights reserved.

Adsorption studies on Pt(111)

International Nuclear Information System (INIS)

Hopster, H.

1977-06-01

The adsorption of O 2 , CO, and C 2 H 2 as well as the CO oxidation on Pt(111) were studied by high-resolution electron spectroscopy. Using a platinum monocrystal sample with a contonuous stage density, the adhesion coefficient for O 2 and the reaction probability for CO were determined as a function of stage density and oxygen cover by measuring the oxygen cover and its time behaviour. The study of vibrations of adsorbed CO showed that CO is bound in linear form on two different adsorption sites. The adsorption of acetylene was studied at 140 K and 300 K. The frequencies of the C-H stretching and flexural vibrations as well as the C-C-H bonding angle were determined. (orig./GSC) [de

Study of HKUST (Copper benzene-1,3,5-tricarboxylate, Cu-BTC MOF)-1 metal organic frameworks for CH4 adsorption: An experimental Investigation with GCMC (grand canonical Monte-carlo) simulation

International Nuclear Information System (INIS)

Sun, Baichuan; Kayal, Sibnath; Chakraborty, Anutosh

2014-01-01

We have measured the methane uptakes on HKUST (Copper benzene-1,3,5-tricarboxylate, Cu-BTC MOF)-1 MOF (metal organic framework) for the temperatures ranging from 120 K to 300 K and pressures up to 10 bar. The experimentally measured HKUST-1 + CH 4 isotherms data are compared with uptakes of various adsorbents and methane systems. We have also simulated the methane uptakes and its density distribution on HKUST-1 employing GCMC (grand canonical Monte-carlo) simulation and compare with experimental data. In this article, we also present an extensive study on characterization and property evaluation of HKUST-1 MOF for CH 4 adsorption characteristics employing XRD (X-ray diffraction), SEM (scanning electron microscope) and TGA (thermo gravimetric analysis). Employing GCMC and the thermodynamic property fields of HKUST-1 + CH 4 system, the isosteric heat of adsorption (Q st ) is calculated and Q st is presented in a T-s (temperature-entropy) diagram. - Highlights: • Characterization of HKUST-1 MOFs by XRD, SEM, N 2 adsorption and TGA. • Measurement of CH 4 uptakes on HKUST-1 by volumetric methods. • GCMC simulation of methane uptakes and its density distribution on HKUST-1. • Isosteric heat of adsorption in a T-s (temperature-entropy) diagram

Adsorptive Removal of Methylene Blue onto ZnCl2 Activated Carbon from Wood Apple Outer Shell: Kinetics and Equilibrium Studies

Directory of Open Access Journals (Sweden)

N. Bhadusha

2011-01-01

Full Text Available Methylene blue dye removal from aqueous solution was investigated using ZnCl2 activated carbon prepared from wood apple outer shell (Limonia acidissima, biomass waste. Influence of agitation time, adsorbent dose, dye concentration, pH and temperature were explored. Two theoretical adsorption isotherms namely Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Qo was found to be 35.1 mg/g and the equilibrium parameter (RL values indicate favourable adsorption. The experimental data were well fitted with Langmuir isotherm model and pseudo second order kinetic model. Desorption studies showed that ion exchange mechanism might be involved in the adsorption process.

Selective adsorption behavior of Cd(II) ion imprinted polymers synthesized by microwave-assisted inverse emulsion polymerization: Adsorption performance and mechanism

International Nuclear Information System (INIS)

Zhu, Fang; Li, Luwei; Xing, Junde

2017-01-01

Highlights: • Microwave assisted inverse emulsion polymerization was applied to prepare Cd(II) imprinted polymers. • The adsorption capacity was evaluated by static adsorption experiments. • Pseudo-second-order model and Langmuir adsorption isotherm model had the best agreement with the experimental data. • The adsorption was a spontaneous and endothermic process. • Cd(II) imprinted polymers have specific identification for Cd(II). - Abstract: Microwave-assisted inverse emulsion polymerization method was used to prepare Cd(II) imprinted polymer (IIP) by using β-cyclodextrin (β-CD) and acrylamide (AM) as functional monomer, epichlorohydrin (ECH) as crossing-linking agent, ammonium persulfate as initiator. The Cd(II) imprinted polymer was characterized by SEM, FTIR and TGA. The influences of initial concentration of Cd(II), pH values, temperature, time and competitive ions on adsorption capacity and recognition properties are investigated. Under the optimal conditions, the adsorption capacity could reach 107 mg/g. Furthermore, pseudo first order kinetic model, pseudo second order kinetic model and intra-particular diffusion model were used to describe the adsorption kinetic behavior. Results showed that the pseudo-second-order model (R"2 0.9928–0.9961) had the best agreement with the experimental data. Langmuir adsorption isotherm model described the experimental data well, which indicated that adsorption was mainly monolayer absorption. Moreover, the study of adsorption thermodynamics (ΔG"0 0, ΔS"0 > 0) suggested that the adsorption process was a spontaneous and endothermic process. Competitive selectivity experiment revealed that imprinted polymer could selectively recognize Cd(II). It provides a new idea for removing Cd(II) from aqueous solution.

Study of Adsorption Mechanism of Congo Red on Graphene Oxide/PAMAM Nanocomposite

Science.gov (United States)

Rafi, Mohammad; Samiey, Babak; Cheng, Chil-Hung

2018-01-01

Graphene oxide/poly(amidoamine) (GO/PAMAM) nanocomposite adsorbed high quantities of congo red (CR) anionic dye in 0.1 M NaCl solution, with the maximum adsorption capacity of 198 mg·g−1. The kinetics and thermodynamics of adsorption were investigated to elucidate the effects of pH, temperature, shaking rate, ionic strength, and contact time. Kinetic data were analyzed by the KASRA model and the KASRA, ISO, and pore-diffusion equations. Adsorption adsorption isotherms were studied by the ARIAN model and the Henry, Langmuir, and Temkin equations. It was shown that adsorption sites of GO/PAMAM at experimental conditions were phenolic hydroxyl groups of GO sheets and terminal amine groups of PAMAM dendrimer. Analysis of kinetic data indicated that amine sites were located on the surface, and that hydroxyl sites were placed in the pores of adsorbent. CR molecules interacted with the adsorption sites via hydrogen bonds. The molecules were adsorbed firstly on the amine sites, and then on the internal hydroxyl sites. Adsorption kinetic parameters indicated that the interaction of CR to the –NH3+ sites was the rate-controlling step of adsorption of CR on this site and adsorption activation energies calculated for different parts of this step. On the other hand, kinetic parameters showed that the intraparticle diffusion was the rate-controlling step during the interaction of CR molecules to –OH sites and activation energy of this step was not calculable. Finally, the used GO/PAMAM was completely regenerated by using ethylenediamine. PMID:29587463

Study of Adsorption Mechanism of Congo Red on Graphene Oxide/PAMAM Nanocomposite

Directory of Open Access Journals (Sweden)

Mohammad Rafi

2018-03-01

Full Text Available Graphene oxide/poly(amidoamine (GO/PAMAM nanocomposite adsorbed high quantities of congo red (CR anionic dye in 0.1 M NaCl solution, with the maximum adsorption capacity of 198 mg·g−1. The kinetics and thermodynamics of adsorption were investigated to elucidate the effects of pH, temperature, shaking rate, ionic strength, and contact time. Kinetic data were analyzed by the KASRA model and the KASRA, ISO, and pore-diffusion equations. Adsorption adsorption isotherms were studied by the ARIAN model and the Henry, Langmuir, and Temkin equations. It was shown that adsorption sites of GO/PAMAM at experimental conditions were phenolic hydroxyl groups of GO sheets and terminal amine groups of PAMAM dendrimer. Analysis of kinetic data indicated that amine sites were located on the surface, and that hydroxyl sites were placed in the pores of adsorbent. CR molecules interacted with the adsorption sites via hydrogen bonds. The molecules were adsorbed firstly on the amine sites, and then on the internal hydroxyl sites. Adsorption kinetic parameters indicated that the interaction of CR to the –NH3+ sites was the rate-controlling step of adsorption of CR on this site and adsorption activation energies calculated for different parts of this step. On the other hand, kinetic parameters showed that the intraparticle diffusion was the rate-controlling step during the interaction of CR molecules to –OH sites and activation energy of this step was not calculable. Finally, the used GO/PAMAM was completely regenerated by using ethylenediamine.

Adsorption and activation of methane and methanol on Pt(100) surface: a density functional study

International Nuclear Information System (INIS)

Moussounda, P.S.

2006-11-01

The activation of methane (CH 4 ) and methanol (CH 3 OH) on Pt(100) surface has been investigated using density functional theory calculations based on plane-wave basis and pseudo-potential. We optimised CH 4 /Pt(100) system. The calculated adsorption energies over the top, bridge and hollow sites are small, weakly dependent on the molecular orientation. The nature of the CH 4 -Pt interaction was examined through the electronic structure changes. The adsorption of methyl (CH 3 ) and hydrogen (H) and the co-adsorption of CH 3 +H were also calculated. From these results, we examined the dissociation of CH 4 to CH 3 +H, and the activation energies found are in good agreement with the experimental and theoretical values. The activation of CH 3 OH/Pt(100) has been studied. All the sites have almost the same adsorption energy. The adsorption of oxygen (O) and the co-adsorption of CH 4 and O were also examined. In addition, the formation of CH 3 OH assuming a one-step mechanism step via the co-adsorption of CH 4 +O has been studied and the barrier height was found to be high. (authors)

The adsorption of oleate on powellite and fluorapatite: A joint experimental and theoretical simulation study

Science.gov (United States)

Zhen, Wang

2017-07-01

Flotation and adsorption performance of sodium oleate(NaOl)on powellite and fluorapatite were investigated in this work through micro-flotation tests, work of adhesion calculations, molecular dynamics simulation, micro-topography studies and FTIR measurements. The micro-flotation results show a similar flotation behaviors of powellite and fluorapatite under alkaline conditions, but a considerable difference in mineral recoveries in the pH range 2-7, which demonstrates the possibilities for separating powillite from fluorapatite under acidic conditions. The great difference in mineral recovery displays a good accordance with the obvious difference in the work of adhesion of powellite and fluorapatite at NaOl dosage range of 40-80 mg/L, obtained from flotation and contact angle measurements, respectively. The more negative interaction energy (ΔE) between NaOl and powellite/water interface from molecular dynamics simulation reveals a more easily adsorption of NaOl onto powellite than onto fluorapatite, which excellently matches with the results of flotation and work of adhesion. The results of micro-topography study shows that the adsorption of NaOl on powellite is mainly ascribed to the chemisorption of oleate ions with Ca2+ on powellite lattice or the precipitation of calcium dioleate agglomerates on powellite surface when it was in the solution without or with Ca2+, respectively. The FTIR measurements further confirm the chemisorption of oleate ions with Ca2+ active sites on powellite surface.

Adsorption characteristics of brilliant green dye on kaolin

International Nuclear Information System (INIS)

Nandi, B.K.; Goswami, A.; Purkait, M.K.

2009-01-01

Experimental investigations were carried out to adsorb toxic brilliant green dye from aqueous medium using kaolin as an adsorbent. Characterization of kaolin is done by measuring: (i) particle size distribution using particle size analyzer, (ii) BET surface area using BET surface analyzer, and (iii) structural analysis using X-ray diffractometer. The effects of initial dye concentration, contact time, kaolin dose, stirring speed, pH and temperature were studied for the adsorption of brilliant green in batch mode. Adsorption experiments indicate that the extent of adsorption is strongly dependent on pH of solution. Free energy of adsorption (ΔG 0 ), enthalpy (ΔH 0 ) and entropy (ΔS 0 ) changes are calculated to know the nature of adsorption. The calculated values of ΔG 0 at 299 K and 323 K indicate that the adsorption process is spontaneous. The estimated values of ΔH 0 and ΔS 0 both show the negative sign, which indicate that the adsorption process is exothermic and the dye molecules are organized on the kaolin surface in less randomly fashion than in solution. The adsorption kinetic has been described by first-order, pseudo-second-order and intra-particle-diffusion models. It was observed that the rate of dye adsorption follows pseudo-second-order model for the dye concentration range studied in the present case. Standard adsorption isotherms were used to fit the experimental equilibrium data. It was found that the adsorption of brilliant green on kaolin follows the Langmuir adsorption isotherm

Adsorption of dyes onto activated carbon cloth: using QSPRs as tools to approach adsorption mechanisms.

Science.gov (United States)

Metivier-Pignon, Hélène; Faur, Catherine; Le Cloirec, Pierre

2007-01-01

The present study aimed to investigate the adsorption of dyes onto activated carbon cloths. Kinetics and isotherms were studied based on results of batch reactors to constitute databases for the adsorption rates and capacities of 22 commercial dyes. Added to a qualitative analysis of experimental results, quantitative structure property relationships (QSPRs) were used to determine the structural features that influence most adsorption processes. QSPRs consisted of multiple linear regressions correlating adsorption parameters with molecular connectivity indices (MCIs) as molecular descriptors. Results related to adsorption kinetics showed that the size of molecules was the significant feature, the high order MCIs involved in QSPRs indicating the influence of a critical size on adsorption rate. Improved statistical fits were obtained when the database was divided according to the chemical classes of dyes. As regards to adsorption isotherms, their particular form led to the use of saturation capacity as the adsorption parameter. By contrast with adsorption kinetics, molecular overcrowding seemed to be of less influence on adsorption equilibrium. In this case, MCIs included in the QSPR were more related to details of the molecular structure. The robustness of the QSPR assessed for azo dyes was studied for the other dyes. Although the small size of the database limited predictive ability, features relevant to the influence of the database composition on QSPRs have been highlighted.

Neutron reflectivity study of critical adsorption. Application to the understanding of environmental mechanisms

International Nuclear Information System (INIS)

Jestin, Jacques

2001-01-01

This study is within the scope of fundamental knowledge transfer to a field case-study, i.e. the understanding of the adsorption properties of binary mixtures against a wall in the case of soil pollution by liquid hydrocarbons. From the theoretical study of critical adsorption, which has been well described in the literature, we carried out experiments on model systems by using neutron techniques. Neutron reflectivity was then applied to the liquid-vapor interface of three different binary mixtures: perfluorohexane-hexane, deuterated methanol-cyclohexane and methanol-deuterated cyclohexane. The experimental data were analysed according to the theoretical prediction of Fisher and De Gennes, along with Liu and Fisher that suggested a power law decrease of the concentration profile (with an exponent equal to 0.52) followed by an exponential function. The characteristic exponent and the amplitude ratios for the methanol-cyclohexane mixtures were found fitted well with theoretical values for the three systems. Only the perfluorohexane-hexane mixture exhibited a particular behavior in the adsorption process that affected the power law amplitude value. This step allowed us to study non critical adsorption and to apply neutrons techniques, e.g. reflectivity and small angles neutrons scattering, to a water-2,5 dimethylpyridine mixture against silica, which is a model system for soils polluted by water/hydrocarbon mixtures. These experiments highlighted new experimental difficulties, which were not fully solved over this study, together with some problems in the analysis that would require specific modelling. Nevertheless, this study shows the capabilities of neutrons techniques to investigate some environmental mechanisms. Moreover, some of the results reported here can be used as a basis for future experiments. (author)

Experimental investigation of a solar adsorption chiller used for grain depot cooling

International Nuclear Information System (INIS)

Luo, H.L.; Dai, Y.J.; Wang, R.Z.; Wu, J.Y.; Xu, Y.X.; Shen, J.M.

2006-01-01

The solar cooling technology is attractive since cooling load of building is roughly in phase with solar energy availability. In this study, a solar adsorption chiller was built and tested with aim of developing an alternative refrigeration system used for grain cooling storage. This solar adsorption chiller consists of four subsystems, namely, a solar water heating unit with 49.4 m 2 solar collecting area, a silica gel-water adsorption chiller, a cooling tower and a fan coil unit. In order to achieve continuous refrigeration, two adsorption units are operated out-of-phase with mass recovery cycle in the adsorption chiller. Field test results show that, under the climatic conditions of daily solar radiation being about 16-21 MJ/m 2 , this solar adsorption chiller can furnish 14-22 deg. C chilled air with an average cooling output ranging from about 3.2-4.4 kW, its daily solar cooling COP (coefficient of performance) is about 0.1-0.13

Response surface modeling of boron adsorption from aqueous solution by vermiculite using different adsorption agents: Box-Behnken experimental design.

Science.gov (United States)

Demirçivi, Pelin; Saygılı, Gülhayat Nasün

2017-07-01

In this study, a different method was applied for boron removal by using vermiculite as the adsorbent. Vermiculite, which was used in the experiments, was not modified with adsorption agents before boron adsorption using a separate process. Hexadecyltrimethylammonium bromide (HDTMA) and Gallic acid (GA) were used as adsorption agents for vermiculite by maintaining the solid/liquid ratio at 12.5 g/L. HDTMA/GA concentration, contact time, pH, initial boron concentration, inert electrolyte and temperature effects on boron adsorption were analyzed. A three-factor, three-level Box-Behnken design model combined with response surface method (RSM) was employed to examine and optimize process variables for boron adsorption from aqueous solution by vermiculite using HDTMA and GA. Solution pH (2-12), temperature (25-60 °C) and initial boron concentration (50-8,000 mg/L) were chosen as independent variables and coded x 1 , x 2 and x 3 at three levels (-1, 0 and 1). Analysis of variance was used to test the significance of variables and their interactions with 95% confidence limit (α = 0.05). According to the regression coefficients, a second-order empirical equation was evaluated between the adsorption capacity (q i ) and the coded variables tested (x i ). Optimum values of the variables were also evaluated for maximum boron adsorption by vermiculite-HDTMA (HDTMA-Verm) and vermiculite-GA (GA-Verm).

Experimental study on solar-powered adsorption refrigeration cycle with activated alumina and activated carbon as adsorbent

Directory of Open Access Journals (Sweden)

Himsar Ambarita

2016-03-01

Full Text Available Typical adsorbent applied in solar-powered adsorption refrigeration cycle is activated carbon. It is known that activated alumina shows a higher adsorption capacity when it is tested in the laboratory using a constant radiation heat flux. In this study, solar-powered adsorption refrigeration cycle with generator filled by different adsorbents has been tested by exposing to solar radiation in Medan city of Indonesia. The generator is heated using a flat-plate type solar collector with a dimension of 0.5 m×0.5 m. Four cases experiments of solar-powered adsorption cycle were carried out, they are with generator filled by 100% activated alumina (named as 100AA, by a mixed of 75% activated alumina and 25% activated carbon (75AA, by a mixed of 25% activated alumina and 75% activated carbon (25AA, and filled by 100% activated carbon. Each case was tested for three days. The temperature and pressure history and the performance have been presented and analyzed. The results show that the average COP of 100AA, 75AA, 25AA, and 100AC is 0.054, 0.056, 0.06, and 0.074, respectively. The main conclusion can be drawn is that for Indonesian condition and flat-plate type solar collector the pair of activated carbon and methanol is the better than activated alumina.

Development and experimental testing of a hybrid Stirling engine-adsorption chiller auxiliary power unit for heavy trucks

International Nuclear Information System (INIS)

Flannery, Barry; Lattin, Robert; Finckh, Oliver; Berresheim, Harald; Monaghan, Rory F.D.

2017-01-01

Highlights: • Free-piston Stirling engine for truck APU. • Waste heat driven adsorption chiller for cab air conditioning. • Reduced-order model comparing proposed system to existing technology. • Experimental test data from prototype test rig. - Abstract: This paper identifies the key technical requirements for a heavy truck auxiliary power unit (APU) and explores a potential alternative technology for use in a next-generation APU which could eliminate key problems related to emissions, noise and maintenance experienced today by conventional diesel engine-vapour compression APUs. The potential performance of a novel hybrid Stirling engine-adsorption chiller concept is investigated and benchmarked against the incumbent technology using a reduced-order model based on experimental data. Experimental results from a Stirling-adsorption system (SAS) prototype test rig are also presented which highlight system integration dynamics and overall performance. The adsorption chiller achieved an average COP of 0.42 ± 0.06 and 2.3 ± 0.1 kW_t of cooling capacity at the baseline test condition. The prototype SAS test rig demonstrates that there appear to be no major technology barriers remaining that would prevent adoption of the SAS concept in a next-generation APU. Such a system could offer a reduction of exhaust emissions, greenhouse gases (GHG), ozone-depleting substances, noise, low maintenance and the potential for fuel flexibility and higher reliability. Preliminary modelling results indicate that the proposed system could offer superior overall electrical and cooling efficiencies compared to incumbent APUs and demonstrate a payback period of 4.6 years.

Adsorption of Nile Blue A from Wastewater Using Magnetic Multi-Walled Carbon Nanotubes: Kinetics and Equilibrium Studies

Directory of Open Access Journals (Sweden)

Mehrnaz Ghoochian

2016-04-01

Full Text Available Background: Synthetic dyes are serious pollutants and wide ranges of methods have been employed for their removal from aquatic systems. We studied the adsorption of "Nile blue A" (NBA, an anionic dye, from aqueous solution by oxidized multi-walled carbon nanotubes (MWCNTs. Methods: Scanning electron microscope and Fourier transform infrared spectroscopy were used to characterize function groups produced at MWCNTs surface. Kinetics and adsorption isotherms of NBA, the effect of temperature, pH, contact time and initial dosage of nanotubes on the adsorption capacity were also assessed. The experimental data were analyzed by Langmuir and Freundlich models. Results: Most of the dye was removed in the first 5 min and best adsorption percentage was at pH 7.0. The equilibrium reached at 45 min. The experimental data were analyzed by Langmuir and Freundlich models and the results fitted well with the Freundlich model. The adsorption kinetic data were analyzed using first-order and the pseudo-second order model and the adsorption kinetic data of NBA dye onto MWCNTs fitted the pseudo-second order model. The maximum adsorption capacity was obtained as 169.49 mg g-1. Conclusion: Freundlich model suggested that the adsorption process followed heterogeneous distribution onto MWCNTs and pseudo-second model of adsorption implied that chemical processes controlled the rate-controlling step. Oxidized MWCNTs could be used as an effective adsorbent for the removal of "Nile Blue A" dye. Oxidization of MWCNTs by nitric acid, improves the efficiency of NBA removal due to increases in functional groups and total number of adsorption sites.

Equilibrium, kinetic and thermodynamic studies for adsorption of BTEX onto Ordered Mesoporous Carbon (OMC).

Science.gov (United States)

Konggidinata, Mas Iwan; Chao, Bing; Lian, Qiyu; Subramaniam, Ramalingam; Zappi, Mark; Gang, Daniel Dianchen

2017-08-15

Chemical and petrochemical industries produce substantial amounts of wastewater everyday. This wastewater contains organic pollutants such as benzene, toluene, ethylbenzene and xylenes (BTEX) that are toxic to human and aquatic life. Ordered Mesoporous Carbon (OMC), the adsorbent that possesses the characteristics of an ideal adsorbent was investigated to understand its properties and suitability for BTEX removal. Adsorption isotherms, adsorption kinetics, the effects of initial BTEX concentrations and temperatures on the adsorption process were studied. The OMCs were characterized using surface area and pore size analyzer, transmission electron microscopy (TEM), elemental analysis, thermogravimetric analysis (TGA) and fourier transform infrared spectroscopy (FTIR). The results suggested that the Langmuir Isotherm and Pseudo-Second-Order Models described the experimental data well. The thermodynamic parameters, Gibbs free energy (ΔG°), the enthalpy change (ΔH°) and the entropy change (ΔS°) of adsorption indicated that the adsorption processes were physical, endothermic, and spontaneous. In addition, OMC had 27% higher overall adsorption capacities compared to granular activated carbon (GAC). Copyright © 2017 Elsevier B.V. All rights reserved.

Kinetic and equilibrium studies of cesium adsorption on ceiling tiles from aqueous solutions.

Science.gov (United States)

Miah, Muhammed Yusuf; Volchek, Konstantin; Kuang, Wenxing; Tezel, F Handan

2010-11-15

A series of experiments were performed to quantify the adsorption of cesium on ceiling tiles as a representative of urban construction materials. Adsorption was carried out from solutions to mimic wet environmental conditions. Non-radioactive cesium chloride was used as a surrogate of the radioactive (137)Cs. The experiments were performed in the range of initial cesium concentrations of 0.114-23.9 mg L(-1) at room temperature (21°C) around three weeks. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). The quantity of adsorbed Cs was calculated by mass balance as a function of time. Two kinetic and three equilibrium models were employed to interpret the test results. Determination of kinetic parameters for adsorption was carried out using the first-order reaction model and the intra-particle diffusion model. Adsorption equilibrium was studied using Langmuir, Freundlich and three-parameter Langmuir-Freundlich adsorption isotherm models. A satisfactory correlation between the experimental and the predicted values was observed. Crown Copyright © 2010. Published by Elsevier B.V. All rights reserved.

Kinetic and equilibrium studies of cesium adsorption on ceiling tiles from aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Volchek, Konstantin, E-mail: Konstantin.Volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Kuang, Wenxing [SAIC Canada, 335 River Road, Ottawa, Ontario, K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, K1N 6N5 (Canada)

2010-11-15

A series of experiments were performed to quantify the adsorption of cesium on ceiling tiles as a representative of urban construction materials. Adsorption was carried out from solutions to mimic wet environmental conditions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. The experiments were performed in the range of initial cesium concentrations of 0.114-23.9 mg L{sup -1} at room temperature (21 deg. C) around three weeks. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). The quantity of adsorbed Cs was calculated by mass balance as a function of time. Two kinetic and three equilibrium models were employed to interpret the test results. Determination of kinetic parameters for adsorption was carried out using the first-order reaction model and the intra-particle diffusion model. Adsorption equilibrium was studied using Langmuir, Freundlich and three-parameter Langmuir-Freundlich adsorption isotherm models. A satisfactory correlation between the experimental and the predicted values was observed.

Modelling phosphate adsorption to the soil: Application of the non-ideal competitive adsorption model

International Nuclear Information System (INIS)

Abou Nohra, Joumana S.; Madramootoo, Chandra A.; Hendershot, William H.

2007-01-01

Phosphorus (P) transport in subsurface runoff has increased despite the limited mobility of P in soils. This study investigated the ability of the non-ideal competitive adsorption (NICA) model to describe phosphate (PO 4 ) adsorption for soils in southern Quebec (Canada). We measured the surface charge and PO 4 adsorption capacity for 11 agricultural soils. Using the experimental data and a nonlinear fitting function, we derived the NICA model parameters. We found that the NICA model described accurately the surface charge of these soils with a mean R 2 > 0.99, and described the adsorption data with a mean R 2 = 0.96. We also found that the variable surface charge was distributed over the two binding sites with the low pH sites demonstrating a stronger binding energy for hydroxyl and PO 4 ions. We established that the NICA model is able to describe P adsorption for the soils considered in this study. - The NICA model accurately described the adsorption of phosphate to some southern Quebec soils

Adsorption performance of silver-loaded activated carbon fibers

Directory of Open Access Journals (Sweden)

Yan Xue-Feng

2018-01-01

Full Text Available Silver-loaded activated carbon fiber is prepared, and its adsorption performance is studied experimentally using five methylene blue solutions with different concentrations under three different temperature conditions. The adsorption tests show that fibers adsorption increase as the increase of temperature, and there is an optimal value for solution concentration, beyond which its adsorption will de-crease. Fibers isothermal adsorption to methylene blue is different from those by the monolayer adsorption by Langmuir model and the multilayer adsorption by Freundlich model. Through the analysis of thermodynamic parameters, Gibbs free energy, standard entropy, and standard enthalpy, it is found that the fibers adsorption to methylene blue is an exothermic process of physical adsorption.

Adsorption of gold onto γ-aminopropyltriethoxysilane grafted coconut pith

International Nuclear Information System (INIS)

Usman, M.; Akhtar, J.

2017-01-01

This study was carried out to investigate adsorption kinetic and adsorption thermodynamics of Au(III) ions onto γ-aminopropyltriethoxysilane grafted coconut pith. The results from equilibrium adsorption were fitted in various adsorption isotherm models such as Langmuir, Freundlich, Temkin and Dubinin-Radushkevich and the best fit for the experimental data was Langmuir isotherm. The maximum adsorption capacity for virgin coconut pith (VCP) and the grafted coconut pith (GCP) were 256.41 and 285.59 mg/g, respectively. The kinetic data was verified using pseudo-first-order, pseudo-second-order, elovich equation and intraparticle diffusion model. The correlation results suggested that the pseudo-second-order model fits the experimental data well. A thermodynamic study revealed the endothermic nature of reaction due to positive enthalpy (?Ho) values and negative values of Gibbs free energy (?Go) describes the spontaneity of adsorption process. The regenerability of VCP and GCP adsorbents were investigated with NaOH (1.0 M).

STUDY OF GAS SEPARATION PROCESS BY DYNAMIC ADSORPTION IN FIXED BED

Directory of Open Access Journals (Sweden)

Ioan Solomon

2010-10-01

Full Text Available An experimental study of mass transfer at gas separation by dynamic adsorption in fixed bed of impregnated silica gel is presented in this work. By means of a mathematical model based on constants and coefficient easy to evaluate, the distributions of adsorbate concentration in gas and solid phases were determined as a function of time and throughout the height of the fixed bed, under isothermal conditions.With this aim, water vapors from air were adsorbed in a fixed bed of impregnated silica gel. The values of the volumetric mass transfer coefficient, Kv, were determined experimentally at several values of air superficial velocity, an air relative humidity of 69�20at 38 °C. The influence of the gas flow velocity and initial water concentration in adsorbent on the distribution of water concentration in both phases was established as a function of time and throughout the height of the fixed bed. The results obtained allow one to determination of the local adsorption rate.

Selective adsorption behavior of Cd(II) ion imprinted polymers synthesized by microwave-assisted inverse emulsion polymerization: Adsorption performance and mechanism

Energy Technology Data Exchange (ETDEWEB)

Zhu, Fang, E-mail: zhufang@tyut.edu.cn [College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan, Shanxi, 030024 (China); Li, Luwei [College of Environmental Science and Engineering, Taiyuan University of Technology, Taiyuan, Shanxi, 030024 (China); Xing, Junde [College of Chemistry and Chemical Engineering, Taiyuan University of Technology, Taiyuan, Shanxi, 030024 (China)

2017-01-05

Highlights: • Microwave assisted inverse emulsion polymerization was applied to prepare Cd(II) imprinted polymers. • The adsorption capacity was evaluated by static adsorption experiments. • Pseudo-second-order model and Langmuir adsorption isotherm model had the best agreement with the experimental data. • The adsorption was a spontaneous and endothermic process. • Cd(II) imprinted polymers have specific identification for Cd(II). - Abstract: Microwave-assisted inverse emulsion polymerization method was used to prepare Cd(II) imprinted polymer (IIP) by using β-cyclodextrin (β-CD) and acrylamide (AM) as functional monomer, epichlorohydrin (ECH) as crossing-linking agent, ammonium persulfate as initiator. The Cd(II) imprinted polymer was characterized by SEM, FTIR and TGA. The influences of initial concentration of Cd(II), pH values, temperature, time and competitive ions on adsorption capacity and recognition properties are investigated. Under the optimal conditions, the adsorption capacity could reach 107 mg/g. Furthermore, pseudo first order kinetic model, pseudo second order kinetic model and intra-particular diffusion model were used to describe the adsorption kinetic behavior. Results showed that the pseudo-second-order model (R{sup 2} 0.9928–0.9961) had the best agreement with the experimental data. Langmuir adsorption isotherm model described the experimental data well, which indicated that adsorption was mainly monolayer absorption. Moreover, the study of adsorption thermodynamics (ΔG{sup 0} < 0, ΔH{sup 0} > 0, ΔS{sup 0} > 0) suggested that the adsorption process was a spontaneous and endothermic process. Competitive selectivity experiment revealed that imprinted polymer could selectively recognize Cd(II). It provides a new idea for removing Cd(II) from aqueous solution.

Adsorption-desorption and hysteresis phenomenon of tebuconazole in Colombian agricultural soils: Experimental assays and mathematical approaches.

Science.gov (United States)

Mosquera-Vivas, Carmen S; Martinez, María J; García-Santos, Glenda; Guerrero-Dallos, Jairo A

2018-01-01

The adsorption-desorption, hysteresis phenomenon, and leachability of tebuconazole were studied for Inceptisol and Histosol soils at the surface (0-10 cm) and in the subsurface (40-50 cm) of an agricultural region from Colombia by the batch-equilibrium method and mathematical approaches. The experimental K fa and K d (L kg -1 ) values (7.9-289.2) decreased with depth for the two Inceptisols and increased with depth for the Histosol due to the organic carbon content, aryl and carbonyl carbon types. Single-point and desorption isotherms depended on adsorption reversibility and suggested that tebuconazole showed hysteresis; which can be adequately evaluated with the single-point desorption isotherm and the linear model using the hysteresis index HI. The most suitable mathematical approach to estimate the adsorption isotherms of tebuconazole at the surface and in the subsurface was that considering the combination of the n-octanol-water partition coefficient, pesticide solubility, and the mass-balance concept. Tebuconazole had similar moderate mobility potential as compared with the values of other studies conducted in temperate amended and unamended soils, but the risk of the fungicide to pollute groundwater sources increased when the pesticide reached subsurface soil layers, particularly in the Inceptisols. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental Study on Treatment of Dyeing Wastewater by Activated Carbon Adsorption, Coagulation and Fenton Oxidation

Science.gov (United States)

Xiaoxu, SUN; Jin, XU; Xingyu, LI

2017-12-01

In this paper dyeing waste water was simulated by reactive brilliant blue XBR, activated carbon adsorption process, coagulation process and chemical oxidation process were used to treat dyeing waste water. In activated carbon adsorption process and coagulation process, the water absorbance values were measured. The CODcr value of water was determined in Fenton chemical oxidation process. Then, the decolorization rate and COD removal rate were calculated respectively. The results showed that the optimum conditions of activated carbon adsorption process were as follows: pH=2, the dosage of activated carbon was 1.2g/L, the adsorption reaction time was 60 min, and the average decolorization rate of the three parallel experiments was 85.30%. The optimum conditions of coagulation experiment were as follows: pH=8~9, PAC dosage was 70mg/L, stirring time was 20min, standing time was 45min, the average decolorization rate of the three parallel experiments was 74.48%. The optimum conditions for Fenton oxidation were Fe2+ 0.05g/L, H2O2 (30%) 14mL/L, pH=3, reaction time 40min. The average CODcr removal rate was 69.35% in three parallel experiments. It can be seen that in the three methods the activated carbon adsorption treatment of dyeing wastewater was the best one.

Oxygen adsorption on the Al9Co2(001) surface: first-principles and STM study

International Nuclear Information System (INIS)

Villaseca, S Alarcón; Loli, L N Serkovic; Ledieu, J; Fournée, V; Dubois, J-M; Gaudry, É; Gille, P

2013-01-01

Atomic oxygen adsorption on a pure aluminum terminated Al 9 Co 2 (001) surface is studied by first-principle calculations coupled with STM measurements. Relative adsorption energies of oxygen atoms have been calculated on different surface sites along with the associated STM images. The local electronic structure of the most favourable adsorption site is described. The preferential adsorption site is identified as a ‘bridge’ type site between the cluster entities exposed at the (001) surface termination. The Al–O bonding between the adsorbate and the substrate presents a covalent character, with s–p hybridization occurring between the states of the adsorbed oxygen atom and the aluminum atoms of the surface. The simulated STM image of the preferential adsorption site is in agreement with experimental observations. This work shows that oxygen adsorption generates important atomic relaxations of the topmost surface layer and that sub-surface cobalt atoms strongly influence the values of the adsorption energies. The calculated Al–O distances are in agreement with those reported in Al 2 O and Al 2 O 3 oxides and for oxygen adsorption on Al(111). (paper)

Solar powered adsorption refrigerator with CPC collection system: Collector design and experimental test

International Nuclear Information System (INIS)

Gonzalez, Manuel I.; Rodriguez, Luis R.

2007-01-01

Solar adsorption cooling systems are usually based on the flat plate collector, whereas little attention has been paid to concentrating collectors. Compound parabolic concentrators (CPC) are a versatile class of solar collectors that can be adapted to a large variety of applications and geometries. This work presents a CPC collector whose tubular receiver contains the sorption bed and where only a portion of the receiver is exposed to sunlight. Geometric characteristics of the proposed CPC, such as the profile, the length and the height of the reflective sheet are given. A prototype of a solar adsorption chiller using this type of collector and the activated carbon-methanol working pair is described, and typical experimental results are reported. In particular, the measured solar COP ranges from 0.078 to 0.096

Adsorption Studies for Arsenic Removal Using Activated Moringa oleifera

OpenAIRE

T. Sumathi; G. Alagumuthu

2014-01-01

A new low cost adsorbent, activated Moringa oleifera has been developed for aqueous arsenic removal. Batch experiments were revealed that As removal was up to 71.3% using activated Moringa oleifera. Kinetics studies revealed that Langmuir isotherm was followed with a better correlation than the Freundlich isotherm. The thermodynamic parameters such as ΔH, ΔS, and ΔG were computed from the experimental data. These values show that the adsorption is endothermic and spontaneous in nature. Thus, ...

Adsorption of cationic dye from aqueous solution by clay as an adsorbent: thermodynamic and kinetic studies

International Nuclear Information System (INIS)

Fil, B.A.; Ozmetn, C.

2012-01-01

In the study, montmorillonite was used as an adsorbent for the removal of methylene blue (MB) from aqueous solutions. Batch studies were performed to address various experimental parameters like contact time, pH, temperature, stirring speed, ionic strength, adsorbent dosage and initial concentration for the removal of this dye. Adsorption rate increased with the increase in initial dye concentration, ionic strength, stirring speed, pH and temperature. Kinetic study showed that the adsorption of dye on montmorillonite was a gradual process. Quasi-equilibrium reached in 3 h. Pseudo-first-order, pseudo-second-order, Elovich, Bangham, mass transfer and intra-particle particle diffusion models were used to fit the experimental data. Pseudo-second-order rate equation was able to provide realistic description of adsorption kinetics. Intra-particle diffusion process was identified as the main mechanism controlling the rate of the dye sorption. The diffusion coefficient, D, was found to increase when the stirring speed, ionic strength and temperature were raised. Thermodynamic activation parameters such as delt G, delt S and del H were also calculated. (author)

Pulse gas chromatographic study of adsorption of substituted aromatics and heterocyclic molecules on MIL-47 at zero coverage.

Science.gov (United States)

Duerinck, Tim; Couck, Sarah; Vermoortele, Frederik; De Vos, Dirk E; Baron, Gino V; Denayer, Joeri F M

2012-10-02

The low coverage adsorptive properties of the MIL-47 metal organic framework toward aromatic and heterocyclic molecules are reported in this paper. The effect of molecular functionality and size on Henry adsorption constants and adsorption enthalpies of alkyl and heteroatom functionalized benzene derivates and heterocyclic molecules was studied using pulse gas chromatography. By means of statistical analysis, experimental data was analyzed and modeled using principal component analysis and partial least-squares regression. Structure-property relationships were established, revealing and confirming several trends. Among the molecular properties governing the adsorption process, vapor pressure, mean polarizability, and dipole moment play a determining role.

Hydrogen Adsorption on Ga2O3 Surface: A Combined Experimental and Computational Study

Energy Technology Data Exchange (ETDEWEB)

Pan, Yun-xiang; Mei, Donghai; Liu, Chang-jun; Ge, Qingfeng

2011-05-03

In the present work, hydrogen adsorption on the Ga2O3 surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) measurements and periodic density functional theory (DFT) calculations. Both the FTIR and DFT studies suggest that H2 dissociates on the Ga2O3 surfaces, producing OH and GaH species. The FTIR bands at 3730, 3700, 3630 and 3600 cm-1 are attributed to the vibration of the OH species whereas those at 2070 and 1990 cm-1 to the GaH species. The structures of the species detected in experiments are established through a comparison with the DFT calculated stretching frequencies. The O atom of the experimentally detected OH species is believed to originate from the surface O3c atom. On the other hand, the H atom that binds the coordinately unsaturated Ga atom results in the experimentally detected GaH species. Dissociation of H2 on the perfect Ga2O3 surface, with the formation of both OH and GaH species, is endothermic and has an energy barrier of 0.90 eV. In contrast, H2 dissociation on the defective Ga2O3 surface with oxygen vacancies, which mainly produces GaH species, is exothermic, with an energy barrier of 0.61 eV. Accordingly, presence of the oxygen vacancies promotes H2 dissociation and production of GaH species on the Ga2O3 surfaces. Higher temperatures are expected to favor oxygen vacancy creation on the Ga2O3 surfaces, and thereby benefit the production of GaH species. This analysis is consistent with the FTIR results that the bands assigned to GaH species become stronger at higher temperatures. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy.

Novel in situ radiotracer methods for the direct and indirect study of chromate adsorption on alumina

International Nuclear Information System (INIS)

Gancs, L.; Nemeth, Z.; Horanyi, G.

2002-01-01

Radiotracer methods, particularly the radiotracer thin foil method, provide unique possibility of in situ monitoring of chromate adsorption on powdered adsorbents. Two different versions of the thin foil method can be distinguished. In the direct method, the species to be studied is labelled and the radiation measured gives direct information on the adsorption of this species. In the indirect method, a different labelled indicator species is added to the system and the adsorption of this species is followed and the adsorption of the species to be studied is determined based on analysis of the competitive adsorption processes. Both methods were used in the present study. In the in situ methods, the radiation measured consists of two main parts, one coming from the solution background, the other originating from the adsorption layer. In the case of the thin foil method using isotopes emitting soft β - radiation or low energy X-ray the solution background is governed and minimised by self-absorption of the radiation. In the direct study we applied an experimental methodology based on the energy selective measurement of the characteristic K α,β X-radiation emitted by the 51 Cr-labelled chromate species, whereas 35 S-labelled sulphate ions were used as the indicator species in the indirect study. (P.A.)

Non-equilibrium dynamics of single polymer adsorption to solid surfaces

NARCIS (Netherlands)

Panja, D.; Barkema, G.T.; Kolomeisky, A.B.

2009-01-01

The adsorption of polymers to surfaces is crucial for understanding many fundamental processes in nature. Recent experimental studies indicate that the adsorption dynamics is dominated by non-equilibrium effects. We investigate the adsorption of a single polymer of length N to a planar solid surface

Experimental study on cryogenic adsorption of methane by activated carbon for helium coolant purification of High-Temperature Gas-cooled Reactor

International Nuclear Information System (INIS)

Chang, Hua; Wu, Zong-Xin; Jia, Hai-Jun

2017-01-01

Highlights: • The cryogenic CH 4 adsorption on activated carbon was studied for design of HTGR. • The breakthrough curves at different conditions were analyzed by the MTZ model. • The CH 4 adsorption isotherm was fitted well by the Toth model and the D-R model. • The work provides valuable reference data for helium coolant purification of HTGR. - Abstract: The cryogenic adsorption behavior of methane on activated carbon was investigated for helium coolant purification of high-temperature gas-cooled reactor by using dynamic column breakthrough method. With helium as carrier gas, experiments were performed at −196 °C and low methane partial pressure range of 0–120 Pa. The breakthrough curves at different superficial velocities and different feed concentrations were measured and analyzed by the mass-transfer zone model. The methane single-component adsorption isotherm was obtained and fitted well by the Toth model and the Dubinin-Radushkevich model. The adsorption heat of methane on activated carbon was estimated. The cryogenic adsorption process of methane on activated carbon has been verified to be effective for helium coolant purification of high-temperature gas-cooled reactor.

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste.

Science.gov (United States)

Namasivayam, C; Sangeetha, D

2005-09-01

The adsorption of thiocyanate onto ZnCl2 activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q0) was found to be 16.2 mg g(-1) of the adsorbent. The per cent adsorption was maximum in the pH range 3.0-7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as DeltaG0, DeltaH0 and DeltaS0 for the adsorption were evaluated. The negative values of DeltaH0 confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.

Adsorption of gases on heterogeneous surfaces

CERN Document Server

Rudzinski, W

1991-01-01

All real solid surfaces are heterogeneous to a greater or lesser extent and this book provides a broad yet detailed survey of the present state of gas adsorption. Coverage is comprehensive and extends from basic principles to computer simulation of adsorption. Underlying concepts are clarified and the strengths and weaknesses of the various methods described are discussed.Key Features* Adsorption isotherm equations for various types of heterogeneous solid surfaces* Methods of determining the nature of surface heterogeneity and porosity from experimental data* Studies of pha

Malachite Green Adsorption by Spent Coffee Grounds

Science.gov (United States)

Syamimie Atirah Mat, Siti; Zati Hanani Syed Zuber, Sharifah; Rahim, Siti Kartini Enche Ab; Sohaimi, Khairunissa Syairah Ahmad; Halim, Noor Amirah Abdul; Fauziah Zainudin, Nor; Aida Yusoff, Nor; Munirah Rohaizad, Nor; Hidayah Ishak, Noor; Anuar, Adilah; Sarip, Mohd Sharizan Md

2018-03-01

In this work, the ability of spent coffee grounds (SCG) as a low-cost adsorbent to remove malachite green (MG) from aqueous solutions was studied. Batch adsorption tests were carried out to observe the effect of various experimental parameters such as contact time, initial concentration of malachite green and adsorbent dosage on the removal of dye. The results obtained show that the percentage of dye removal will decreased with the increased of initial concentration of dye in the range of 50 mg/L to 250 mg/L. Besides, percentage removal of dye was also found to be increased as the contact time increased until it reached equilibrium condition. The results also showed that the adsorbent dosage in range of 0.2 g to 1.0 g is proportional to the percentage removal of malachite green dye. Study on the kinetic adsorption and isotherm adsorption has also been investigated. The adsorption isotherm data were described by Langmuir isotherm with high-correlation coefficients while the experimental data showed the pseudo-second-order kinetics model was the best model for the adsorption of MG by SCG with the coefficients of correlation R2 > 0.9978.

First-principles study of the pentacene/Cu(1 1 1) interface: Adsorption states and vacuum level shifts

International Nuclear Information System (INIS)

Toyoda, Kenji; Nakano, Yosuke; Hamada, Ikutaro; Lee, Kyuho; Yanagisawa, Susumu; Morikawa, Yoshitada

2009-01-01

We have studied the interaction of pentacene with a Cu(1 1 1) surface using density functional theory (DFT) within a generalized gradient approximation (GGA) and the van der Waals density functional [vdW-DF, M. Dion, H. Rydberg, E. Schroeder, D.C. Langreth, B.I. Lundqvist, Phys. Rev. Lett. 92 (2004) 246401]. The adsorption energy is accurately predicted by vdW-DF, while the equilibrium distances between pentacene and the metal substrate (Z C ) are overestimated by both GGA and vdW-DF. The work function changes depend significantly on Z C . The experimental work function change can be successfully reproduced by GGA if the experimentally reported adsorption geometry is used, whereas the magnitude of the work function change is underestimated if calculated adsorption geometries are applied. We examined the IDIS model [H. Vazquez, R. Qszwaldowski, P. Pou, J. Ortega, R. Perez, F. Flores, A. Kahn, Europhys. Lett. 65 (2004) 802] to compare it with the GGA results. The interface dipoles estimated by the IDIS model fairly agree with the GGA results, provided that the adsorption distance is large. On the other hand, they tend to deviate from the GGA results as the adsorption distance becomes smaller, where back donation from the metal surface to the adsorbate occurs. Our analysis reveals that at experimentally reported metal-organic distance, back donation is significant enough to induce polarization of pentacene molecules perpendicular to the surface, which leads to a reduction of the work function. Thus, at the experimentally reported metal-organic distance, the work function change estimated by a simple IDIS model deviates from that calculated by self-consistent GGA calculations. We also found that at the experimentally reported metal-organic distance, the transferred electrons create weak chemical bonds between pentacene and the Cu(1 1 1) surface, illustrating the reactive nature of pentacene.

Arsenic Adsorption Equilibrium Concentration and Adsorption Rate of Activated Carbon Coated with Ferric-Aluminum Hydroxides

Science.gov (United States)

Zhang, M.; Sugita, H.; Oguma, T.; Hara, J.; Takahashi, S.

2015-12-01

In some areas of developing countries, ground or well water contaminated with arsenic has been reluctantly used as drinking water. It is highly desirable that effective and inexpensive arsenic removal agents should be developed and provided to reduce the potential health risk. Previous studies demonstrated that activated carbon coated with ferric-aluminum hydroxides (Fe-Al-C) has high adsorptive potential for removal of arsenic. In this study, a series of experiments using Fe-Al-C were carried to discuss adsorption equilibrium time, adsorption equilibrium concentration and adsorption rate of arsenic for Fe-Al-C. Fe-Al-C used in this study was provided by Astec Co., Ltd. Powder reagent of disodium hydrogen arsenate heptahydrate was dissolved into ion-exchanged water. The solution was then further diluted with ion-exchanged water to be 1 and 10 mg/L as arsenic concentration. The pH of the solution was adjusted to be around 7 by adding HCl and/or NaOH. The solution was used as artificial arsenic contaminated water in two types of experiments (arsenic adsorption equilibrium and arsenic adsorption rate tests). The results of the arsenic equilibrium tests were showed that a time period of about 3 days to reach apparent adsorption equilibrium for arsenic. The apparent adsorption equilibrium concentration and adsorbed amount of arsenic on Fe-Al-C adsorbent could be estimated by application of various adsorption isotherms, but the distribution coefficient of arsenic between solid and liquid varies with experimental conditions such as initial concentration of arsenic and addition concentration of adsorbent. An adsorption rate equation that takes into account the reduction in the number of effective adsorption sites on the adsorbent caused by the arsenic adsorption reaction was derived based on the data obtained from the arsenic adsorption rate tests.

Preparation of methacrylic acid-modified rice husk improved by an experimental design and application for paraquat adsorption

International Nuclear Information System (INIS)

Hsu, Shih-Tong; Chen, Lung-Chuan; Lee, Cheng-Chieh; Pan, Ting-Chung; You, Bing-Xuan; Yan, Qi-Feng

2009-01-01

Methacrylic acid (MAA) grafted rice husk was synthesized using graft copolymerization with Fenton's reagent as the redox initiator and applied to the adsorption of paraquat. The highest grafting percentage of 44.3% was obtained using the traditional kinetic method. However, a maximum grafting percentage of 65.3% was calculated using the central composite design. Experimental results based on the recipes predicted from the statistical analysis are consistent with theoretical calculations. A representative polymethacrylic acid-g-rice husk (PMAA-g-rice husk) copolymer was hydrolyzed to a salt type and applied to the adsorption of paraquat. The adsorption equilibrium data correlate more closely with the Langmuir isotherm than with the Freundlich equation. The maximum adsorption capacity of modified rice husk is 292.5 mg/g-adsorbent. This value exceeds those for Fuller's earth and activated carbon, which are the most common binding agents used for paraquat. The samples at various stages were characterized by solid-state 13 C NMR spectroscopy.

Preparation of methacrylic acid-modified rice husk improved by an experimental design and application for paraquat adsorption

Energy Technology Data Exchange (ETDEWEB)

Hsu, Shih-Tong, E-mail: shihtong@mail.ksu.edu.tw [Department of Polymer Materials, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City, Tainan Hsien, Taiwan (China); Chen, Lung-Chuan, E-mail: lcchen@mail.ksu.edu.tw [Department of Polymer Materials, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City, Tainan Hsien, Taiwan (China); Lee, Cheng-Chieh, E-mail: etmediagoing@yahoo.com.tw [Department of Environmental Engineering, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City 710, Tainan Hsien, Taiwan (China); Pan, Ting-Chung, E-mail: tcpan@mail.ksu.edutw [Department of Environmental Engineering, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City 710, Tainan Hsien, Taiwan (China); You, Bing-Xuan, E-mail: kp2681@yahoo.com.tw [Department of Polymer Materials, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City, Tainan Hsien, Taiwan (China); Yan, Qi-Feng, E-mail: rsrs0938@yahoo.com.tw [Department of Polymer Materials, Kun Shan University, No. 949 Da-Wan Rd., Yung-Kang City, Tainan Hsien, Taiwan (China)

2009-11-15

Methacrylic acid (MAA) grafted rice husk was synthesized using graft copolymerization with Fenton's reagent as the redox initiator and applied to the adsorption of paraquat. The highest grafting percentage of 44.3% was obtained using the traditional kinetic method. However, a maximum grafting percentage of 65.3% was calculated using the central composite design. Experimental results based on the recipes predicted from the statistical analysis are consistent with theoretical calculations. A representative polymethacrylic acid-g-rice husk (PMAA-g-rice husk) copolymer was hydrolyzed to a salt type and applied to the adsorption of paraquat. The adsorption equilibrium data correlate more closely with the Langmuir isotherm than with the Freundlich equation. The maximum adsorption capacity of modified rice husk is 292.5 mg/g-adsorbent. This value exceeds those for Fuller's earth and activated carbon, which are the most common binding agents used for paraquat. The samples at various stages were characterized by solid-state {sup 13}C NMR spectroscopy.

Preparation of methacrylic acid-modified rice husk improved by an experimental design and application for paraquat adsorption.

Science.gov (United States)

Hsu, Shih-Tong; Chen, Lung-Chuan; Lee, Cheng-Chieh; Pan, Ting-Chung; You, Bing-Xuan; Yan, Qi-Feng

2009-11-15

Methacrylic acid (MAA) grafted rice husk was synthesized using graft copolymerization with Fenton's reagent as the redox initiator and applied to the adsorption of paraquat. The highest grafting percentage of 44.3% was obtained using the traditional kinetic method. However, a maximum grafting percentage of 65.3% was calculated using the central composite design. Experimental results based on the recipes predicted from the statistical analysis are consistent with theoretical calculations. A representative polymethacrylic acid-g-rice husk (PMAA-g-rice husk) copolymer was hydrolyzed to a salt type and applied to the adsorption of paraquat. The adsorption equilibrium data correlate more closely with the Langmuir isotherm than with the Freundlich equation. The maximum adsorption capacity of modified rice husk is 292.5mg/g-adsorbent. This value exceeds those for Fuller's earth and activated carbon, which are the most common binding agents used for paraquat. The samples at various stages were characterized by solid-state (13)C NMR spectroscopy.

Adsorption of surfactants on sand surface in enhanced oil recovery: Isotherms, kinetics and thermodynamic studies

Energy Technology Data Exchange (ETDEWEB)

Bera, Achinta; Kumar, T.; Ojha, Keka; Mandal, Ajay, E-mail: mandal_ajay@hotmail.com

2013-11-01

Adsorption of surfactants onto reservoir rock surface may result in the loss and reduction of their concentrations in surfactant flooding, which may render them less efficient or ineffective in practical applications of enhanced oil recovery (EOR) techniques. Surfactant flooding for EOR received attraction due to its ability to increase the displacement efficiency by lowering the interfacial tension between oil and water and mobilizing the residual oil. This article highlights the adsorption of surfactants onto sand surface with variation of different influencing factors. It has been experimentally found that adsorption of cationic surfactant on sand surface is more and less for anionic surfactant, while non-ionic surfactant shows intermediate behaviour. X-ray diffraction (XRD) study of clean sand particles has been made to determine the main component present in the sand particles. The interaction between sand particles and surfactant has been studied by Fourier Transform Infrared (FTIR) Spectroscopy of the sand particles before and after aging with surfactant. Salinity plays an important role in adsorption of anionic surfactant. Batch experiments were also performed to understand the effects of pH and adsorbent dose on the sorption efficiency. The sand particles exhibited high adsorption efficiency at low pH for anionic and nonionic surfactants. But opposite trend was found for cationic surfactant. Adsorption data were analyzed by fitting with Langmuir, Freundlich, Redlich-Peterson, and Sips isotherm models. Results show that the Langmuir isotherm and pseudo-second order kinetics models suit the equilibrium and kinetics of adsorption on sand surface. Thermodynamics feasibility of the adsorption process was also studied to verify the spontaneity of the process.

Adsorption behavior of Am(III) on granite

International Nuclear Information System (INIS)

Zhang Yingjie; Feng Xiaogui; Liang Junfu; Chen Jing; Su Rui; Wang Ju; Liu Chunli

2009-01-01

The adsorption behavior of Am(III) on granite (sampled from drilling well BS01 at Beishan (BS) area--a potential candidate site for China's high-level radioactive waste repository, the granite sample's depth about 300 m) was studied in BS03 well groundwater by a batch technique at (25±1) degree C. The influences of pH, sulphate ion, total carbonate ion, humic acid, and concentration of the Am(III) on the adsorption behavior were also studied, and the possible adsorption mechanism was discussed. Experimental results show that the adsorption distribution rate of Am(III) on granite increases with increasing pH of aqueous phase. The chemical composition of the groundwater is the main factor which influences the species of Am(III) and adsorption behavior. The adsorption mechanism of Am(III) on granite is surface complexation. The adsorption isotherm of Am(III) on granite can be described by Freundlich's equation. (authors)

Experimental study and computerized simulation of the elements fixation in trace on mineral oxides. Contribution to the study of natural solids adsorption properties

International Nuclear Information System (INIS)

Marmier, N.

1994-12-01

The aim of this work is to identify some natural or synthetical materials allowing the nuclear wastes confinement in underground geological sites by adsorption of radioelements. The materials composition variety which can be used is very large it is then necessary to make use of models able to predict solid complexes behaviour towards the adsorption from known properties of parent constituents. This type of model still does not exist and its focusing requires the demonstration of mineral complexes parent constituents intrinsic properties additivity. The oxides as aluminium or silicon oxides being parent constituents, the author has demonstrated their properties additivity in an aluminium-silicon oxides physical mixture and in an aluminium silicate : the kaolinite. These surface properties have been determined for different quantities of aluminium and silicon oxides in a 0,1 M sodium nitrate. This study has been realized following the steps below : choice of a theoretical concept describing the adsorption adapted to the studied solid-solution system : the surface complexation model at constant capacitance; the focusing of a surface chemical and physical parameters determination method; the verification of these properties additivity on the aluminium-silicon oxides mixture and on the kaolinite. The studied cation for the adsorption on these materials is the ytterbium trivalent ion because the behaviour of the trivalent ions towards the adsorption is not very well known and because the lanthanides are considered as compounds similar to some fission products present in radioactive wastes. The method used for this work is applicable to all the other ions. (O.L.). 73 refs., 91 figs., 14 tabs

Investigation of adsorption performance deterioration in silica gel–water adsorption refrigeration

International Nuclear Information System (INIS)

Wang Dechang; Zhang Jipeng; Xia Yanzhi; Han Yanpei; Wang Shuwei

2012-01-01

Highlights: ► Adsorption deterioration of silica gel in refrigeration systems is verified. ► Possible factors to cause such deterioration are analyzed. ► Specific surface area, silanol content and adsorption capacity are tested. ► The pollution is the primary factor to decline the adsorption capacity. ► Deteriorated samples are partly restored after being processed by acid solution. - Abstract: Silica gel acts as a key role in adsorption refrigeration systems. The adsorption deterioration must greatly impact the performance of the silica gel–water adsorption refrigeration system. In order to investigate the adsorption deterioration of silica gel, many different silica gel samples were prepared according to the application surroundings of silica gel in adsorption refrigeration systems after the likely factors to cause such deterioration were analyzed. The specific surface area, silanol content, adsorption capacity and pore size distribution of those samples were tested and the corresponding adsorption isotherms were achieved. In terms of the experimental data comparisons, it could be found that there are many factors to affect the adsorption performance of silica gel, but the pollution was the primary one to decline the adsorption capacity. In addition, the adsorption performance of the deteriorated samples after being processed by acid solution was explored in order to find the possible methods to restore its adsorption performance.

Study of water vapour adsorption kinetics on aluminium oxide materials

Science.gov (United States)

Livanova, Alesya; Meshcheryakov, Evgeniy; Reshetnikov, Sergey; Kurzina, Irina

2017-11-01

Adsorbents on the basis of active aluminum oxide are still of demand on the adsorbent-driers market. Despite comprehensive research of alumina adsorbents, and currently is an urgent task to improve their various characteristics, and especially the task of increasing the sorption capacity. In the present work kinetics of the processes of water vapours' adsorption at room temperature on the surface of desiccant samples has been studied. It was obtained on the basis of bayerite and pseudoboehmite experimentally. The samples of pseudoboehmite modified with sodium and potassium ions were taken as study objects. The influence of an adsorbent's grain size on the kinetics of water vapours' adsorption was studied. The 0.125-0.25 mm and 0.5-1.0 mm fractions of this sample were used. It has been revealed that the saturation water vapor fine powder (0.125-0.25 mm) is almost twofold faster in comparison with the sample of fraction 0.5-1.0 mm due to the decrease in diffusion resistance in the pores of the samples when moving from the sample of larger fraction to the fine-dispersed sample. It has been established that the adsorption capacity of the pseudoboehmite samples, modified by alkaline ions, is higher by ˜40 %, than for the original samples on the basis of bayerite and pseudoboehmite.

Physical adsorption and molecular dynamics

International Nuclear Information System (INIS)

Cohan, N.V.

1981-01-01

Some aspects of noble gases adsorption (except He) on graphite substracts are reviewed. Experimental results from this adsorption are analyzed and compared with molecular dynamics calculations. (L.C.) [pt

First principles study of dissolved oxygen water adsorption on Fe (001 surfaces

Directory of Open Access Journals (Sweden)

Dong ZHANG

2018-02-01

Full Text Available In order to study the mechanism of dissolved oxygen content on the surface corrosion behavior of Fe-based heat transfer, the first principle is used to study the adsorption of O2 monomolecular, H2O monolayer and dissolved oxygen system on Fe-based heat transfer surface. The GGA/PBE approximation is used to calculate the adsorption energy, state density and population change during the adsorption process. Calculations prove that when the dissolved oxygen is adsorbed on the Fe-based surface, the water molecule tends to adsorb at the top sites, and the oxygen molecule tends to adsorb at Griffiths. When the H2O molecule adsorbs and interacts on the Fe (001 surface, the charge distribution of the interfacial double electric layer changes to cause the Fe atoms to lose electrons, resulting in the change of the surface potential. When the O2 molecule adsorbs on the Fe (001 crystal surfaces, the electrons on the Fe (001 surface are lost and the surface potential increases. O2 molecule and the surface of the Fe atoms are prone to electron transfer, in which O atom's 2p orbit for the adsorption of O2 molecule on Fe (001 crystal surface play a major role. With the increase of the proportion of O2 molecule in the dissolved oxygen water, the absolute value of the adsorption energy increases, and the interaction of the Fe-based heat transfer surface is stronger. This study explores the influence law of different dissolved oxygen on the Fe base heat exchange surface corrosion, and the base metal corrosion mechanism for experimental study provides a theoretical reference.

Determination of adsorption parameters in numerical simulation for polymer flooding

Science.gov (United States)

Bao, Pengyu; Li, Aifen; Luo, Shuai; Dang, Xu

2018-02-01

A study on the determination of adsorption parameters for polymer flooding simulation was carried out. The study mainly includes polymer static adsorption and dynamic adsorption. The law of adsorption amount changing with polymer concentration and core permeability was presented, and the one-dimensional numerical model of CMG was established under the support of a large number of experimental data. The adsorption laws of adsorption experiments were applied to the one-dimensional numerical model to compare the influence of two adsorption laws on the historical matching results. The results show that the static adsorption and dynamic adsorption abide by different rules, and differ greatly in adsorption. If the static adsorption results were directly applied to the numerical model, the difficulty of the historical matching will increase. Therefore, dynamic adsorption tests in the porous medium are necessary before the process of parameter adjustment in order to achieve the ideal history matching result.

Evaluation of a Mathematical Model for Single Component Adsorption Equilibria with Reference to the Prediction of Multicomponent Adsorption Equilibria

DEFF Research Database (Denmark)

Krøll, Annette Elisabeth; Marcussen, Lis

1997-01-01

An equilibrium equation for pure component adsorption is compared to experiments and to the vacancy solution theory. The investigated equilibrium equation is a special case of a model for prediction of multicomponent adsorption equilibria.The vacancy solution theory for multicomponent systems...... requires binary experimental data for determining the interaction parameters of the Wilson equation; thus a large number of experiments are needed. The multicomponent equilibria model which is investigated for single component systems in this work is based on pure component data only. This means...... that the requirement for experimental data is reduced significantly.The two adsorption models are compared, using experimental pure gas adsorption data found in literature. The results obtained by the models are in close agreement for pure component equilibria and they give a good description of the experimental data...

A computational study of adsorption of divalent metal ions on graphene oxide

Directory of Open Access Journals (Sweden)

Somphob Thompho

2017-12-01

Full Text Available Adsorption of divalent metal ions (Pb2+,Cd2+, Zn2+,Cu2+ on graphene oxide (GO was studied using density functional theory (DFT. Adsorption geometries and energies, as well as the nature of the binding energy, were calculated for the interaction of divalent metal ions with oxygen-containing groups on the surface of GO. The configurations of the complexes were modeled by placing the divalent metal ions above the center and perpendicular to the surface. Binding of Cu2+ to the GO sheet was predicted to be much stronger than that for other divalent metal ions. Calculated results show good agreement with experimental observations and provide useful information for environmental pollution cleanup.

ADSORPTION OF GIBBERELLIC ACID ONTO NATURAL KAOLIN FROM TATAKAN, SOUTH KALIMANTAN

Directory of Open Access Journals (Sweden)

Sunardi Sunardi

2010-06-01

Full Text Available Adsorption of gibberellic acid (GA3 onto raw and purified kaolin from Tatakan, South Kalimantan was investigated in this study. Purification process was done by sedimentation to obtain relative pure kaolinite. Raw and purified kaolin samples were characterized by Fourier transformed infrared (FTIR spectroscopy and X-ray diffractometer (XRD. The adsorption process was carried out in a batch system and the effect of pH, contact time and GA3 concentration were experimentally studied to evaluate the adsorption capacity. The amount of GA3 adsorbed was determined by UV spectrophotometer. The result showed that the raw kaolin from South Kalimantan consist of 53.36% kaolinite, 29.47% halloysite, 4.47% chlorite, 11.32% quartz and 1.38% christobalite and the purified kaolin consist of 73.03% kaolinite, 22.6% halloysite, 0.77% chlorite, 1.37% quartz and 2.23% christobalite Adsorption experimental indicate that the optimum adsorption took place at pH 7 and contact time for 4 h. Adsorption of GA3 was described by the Langmuir adsorption isotherm model with adsorption capacity of 8.91 mg/g on raw kaolin and 10.38 mg/g on purified kaolin.   Keywords: kaolin, gibberellic acid, adsorption

Inhibition of mild steel corrosion in acid solution by Pheniramine drug: Experimental and theoretical study

International Nuclear Information System (INIS)

Ahamad, Ishtiaque; Prasad, Rajendra; Quraishi, M.A.

2010-01-01

Inhibition of mild steel corrosion in 1 M HCl solution by Pheniramine drug was studied using weight loss, electrochemical impedance spectroscopy, linear polarization resistance, and potentiodynamic polarization measurements. The values of activation energy (E a ) and different thermodynamic parameters such as adsorption equilibrium constant (K ads ), free energy of adsorption (ΔG ads o ), adsorption enthalpy (ΔH ads o ) and adsorption entropy (ΔS ads o ) were calculated and discussed. The adsorption process of studied drug on mild steel surface obeys the Langmuir adsorption isotherm. Potentiodynamic polarization measurements showed that Pheniramine is mixed-type inhibitor. Further, theoretical calculations were carried out and relations between computed parameters and experimental inhibition efficiency were discussed.

Potential Theory of Multicomponent Adsorption

DEFF Research Database (Denmark)

Shapiro, Alexander; Stenby, Erling Halfdan

1998-01-01

We developed a theory of multicomponent adsorption on the basis of the potential concept originally suggested by Polanyi. The mixture is considered as a heterogeneous substance segregated in the external field emitted by the adsorbent. The same standard equation of state, with no additional fitting...... parameters, is used for the segregated and for the bulk phases. With this approach, few parameters are needed to correlate pure component adsorption isotherms. These parameters may be used to predict adsorption equilibria of multicomponent mixtures without additional adjustment. A connection between...... the potential theory and the spreading pressure concept is established, and problems of the theory consistency are studied. Numerical algorithms are suggested for evaluation of the segregated state of the mixture in the potential field of adsorption forces. Comparison with experimental data shows good agreement...

Adsorption of ammonium ion by coconut shell-activated carbon from aqueous solution: kinetic, isotherm, and thermodynamic studies.

Science.gov (United States)

Boopathy, Ramasamy; Karthikeyan, Sekar; Mandal, Asit Baran; Sekaran, Ganesan

2013-01-01

Ammonium ions are one of the most encountered nitrogen species in polluted water bodies. High level of ammonium ion in aqueous solution imparts unpleasant taste and odor problems, which can interfere with the life of aquatics and human population when discharged. Many chemical methods are developed and being used for removal of ammonium ion from aqueous solution. Among various techniques, adsorption was found to be the most feasible and environmentally friendly with the use of natural-activated adsorbents. Hence, in this study, coconut shell-activated carbon (CSAC) was prepared and used for the removal of ammonium ion by adsorption techniques. Ammonium chloride (analytical grade) was purchased from Merck Chemicals for adsorption studies. The CSAC was used to adsorb ammonium ions under stirring at 100 rpm, using orbital shaker in batch experiments. The concentration of ammonium ion was estimated by ammonia distillate, using a Buchi distillation unit. The influence of process parameters such as pH, temperature, and contact time was studied for adsorption of ammonium ion, and kinetic, isotherm models were validated to understand the mechanism of adsorption of ammonium ion by CSAC. Thermodynamic properties such as ∆G, ∆H, and ∆S were determined for the ammonium adsorption, using van't Hoff equation. Further, the adsorption of ammonium ion was confirmed through instrumental analyses such as SEM, XRD, and FTIR. The optimum conditions for the effective adsorption of ammonium ion onto CSAC were found to be pH 9.0, temperature 283 K, and contact time 120 min. The experimental data was best followed by pseudosecond order equation, and the adsorption isotherm model obeyed the Freundlich isotherm. This explains the ammonium ion adsorption onto CSAC which was a multilayer adsorption with intraparticle diffusion. Negative enthalpy confirmed that this adsorption process was exothermic. The instrumental analyses confirmed the adsorption of ammonium ion onto CSAC.

Novel experimental methodology for the characterization of thermodynamic performance of advanced working pairs for adsorptive heat transformers

International Nuclear Information System (INIS)

Frazzica, Andrea; Sapienza, Alessio; Freni, Angelo

2014-01-01

This paper presents a novel experimental protocol for the evaluation of the thermodynamic performance of working pairs for application in adsorption heat pumps and chillers. The proposed approach is based on the experimental measurements of the main thermo-physical parameters of adsorbent pairs, by means of a DSC/TG apparatus modified to work under saturated vapour conditions, able to measure the ads-/desorption isobars and heat flux as well as the adsorbent specific heat under real boundary conditions. Such kind of activity allows to characterize the thermodynamic performance of an adsorbent pair allowing the estimation of the thermal Coefficient Of Performance (COP) both for heating and cooling applications, only relying on experimental values. The experimental uncertainty of the method has been estimated to be around 2%, for the COP evaluation. In order to validate the proposed procedure, a first test campaign has been carried out on the commercial adsorbent material, AQSOA-Z02, produced by MPI (Mitsubishi Plastics Inc.), while water was used as refrigerant. The proposed experimental methodology will be applied on several other adsorbent materials, either already on the market or still under investigation, in order to get an easy and reliable method to compare thermodynamic performance of adsorptive working pairs

Study on Shale Adsorption Equation Based on Monolayer Adsorption, Multilayer Adsorption, and Capillary Condensation

OpenAIRE

Chen, Qing; Tian, Yuanyuan; Li, Peng; Yan, Changhui; Pang, Yu; Zheng, Li; Deng, Hucheng; Zhou, Wen; Meng, Xianghao

2017-01-01

Shale gas is an effective gas resource all over the world. The evaluation of pore structure plays a critical role in exploring shale gas efficiently. Nitrogen adsorption experiment is one of the significant approaches to analyze pore size structure of shale. Shale is extremely heterogeneous due to component diversity and structure complexity. Therefore, adsorption isotherms for homogeneous adsorbents and empirical isotherms may not apply to shale. The shape of adsorption-desorption curve indi...

Adsorption dynamics and equilibrium studies of Zn (II)

Indian Academy of Sciences (India)

Batch equilibration studies are conducted to determine the nature of adsorption of zinc (II) over chitosan. The factors affecting the adsorption process like particle size, contact time, dosage, pH, effects of chloride and nitrate are identified. The influence of temperature and co-ions on the adsorption process is verified.

Comparative Study of Textural Characteristics on Methane Adsorption for Carbon Spheres Produced by CO2 Activation

Directory of Open Access Journals (Sweden)

Wen Yang

2014-01-01

Full Text Available Resorcinol-formaldehyde resin polymer was used as raw material for preparation of carbon spheres. Samples were treated with CO2 flow at 850°C by varying activation times. The CO2 activation granted better pore development of pore structure. The experimental data of CH4 adsorption as a function of equilibrium pressure was fitted by Langmuir and Dubinin-Astakhov (D-A models. It was concluded that the high surface area and micropore volume of carbon spheres did unequivocally determine methane capacities. In addition, a thermodynamic study of the heat of adsorption of CH4 on the carbon spheres was carried out. Adsorption of CH4 on carbon spheres showed a decrease in the adsorption heat with CH4 occupancy, and the heat of adsorption fell from 20.51 to 12.50 kJ/mol at 298 K and then increased to a little higher values at a very high loading (>0.70, indicating that CH4/CH4 interactions within the adsorption layer became significant.

Column Adsorption Studies for the Removal of Cr(VI Ions by Ethylamine Modified Chitosan Carbonized Rice Husk Composite Beads with Modelling and Optimization

Directory of Open Access Journals (Sweden)

S. Sugashini

2013-01-01

Full Text Available The objective of this present study is the optimization of process parameters in adsorption of Cr(VI ions by ethylamine modified chitosan carbonized rice husk composite beads (EAM-CCRCBs using response surface methodology (RSM and continuous adsorption studies of Cr(VI ions by ethylamine modified chitosan carbonized rice husk composite beads (EAM-CCRCBs. The effect of process variables such as initial metal ion concentration, adsorbent dosage and pH were optimized using RSM in order to ensure high adsorption capacity at low adsorbent dosage and high initial metal ion concentration of Cr(VI in batch process. The optimum condition suggested by the model for the process variable such as adsorbent dosage, pH and initial metal ion concentration was 0.14 g, 300 mg/L and pH2 with maximum removal of 99.8% and adsorption capacity of 52.7 mg/g respectively. Continuous adsorption studies were conducted under optimized initial metal ion concentration and pH for the removal of Cr(VI ions using EAM-CCRCBs. The breakthrough curve analysis was determined using the experimental data obtained from the continuous adsorption. Continuous adsorption modelling such as bed depth service model and Thomson model were established by fitting it with experimental data.

Hydrogen adsorption on bimetallic PdAu(111) surface alloys

DEFF Research Database (Denmark)

Takehiro, Naoki; Liu, Ping; Bergbreiter, Andreas

2014-01-01

The adsorption of hydrogen on structurally well defined PdAu-Pd(111) monolayer surface alloys was investigated in a combined experimental and theoretical study, aiming at a quantitative understanding of the adsorption and desorption properties of individual PdAu nanostructures. Combining...... the structural information obtained by high resolution scanning tunneling microscopy (STM), in particular on the abundance of specific adsorption ensembles at different Pd surface concentrations, with information on the adsorption properties derived from temperature programmed desorption (TPD) spectroscopy...... and high resolution electron energy loss spectroscopy (HREELS) provides conclusions on the minimum ensemble size for dissociative adsorption of hydrogen and on the adsorption energies on different sites active for adsorption. Density functional theory (DFT) based calculations give detailed insight...

The adsorption of oleate on powellite and fluorapatite: A joint experimental and theoretical simulation study

Energy Technology Data Exchange (ETDEWEB)

Zhen, Wang, E-mail: 544590553@qq.com

2017-07-01

Highlights: • Flotation of powellite from fluorapatite at pH 2–7 using 50–80 mg/L sodium oleate can be achieved. • Oleate chemisorbs on powellite by interaction of carboxylate group with lattice Ca atoms. • Calcium dioleate precipitates can also adsorb on powellite surface. - Abstract: Flotation and adsorption performance of sodium oleate(NaOl)on powellite and fluorapatite were investigated in this work through micro-flotation tests, work of adhesion calculations, molecular dynamics simulation, micro-topography studies and FTIR measurements. The micro-flotation results show a similar flotation behaviors of powellite and fluorapatite under alkaline conditions, but a considerable difference in mineral recoveries in the pH range 2–7, which demonstrates the possibilities for separating powillite from fluorapatite under acidic conditions. The great difference in mineral recovery displays a good accordance with the obvious difference in the work of adhesion of powellite and fluorapatite at NaOl dosage range of 40–80 mg/L, obtained from flotation and contact angle measurements, respectively. The more negative interaction energy (ΔE) between NaOl and powellite/water interface from molecular dynamics simulation reveals a more easily adsorption of NaOl onto powellite than onto fluorapatite, which excellently matches with the results of flotation and work of adhesion. The results of micro-topography study shows that the adsorption of NaOl on powellite is mainly ascribed to the chemisorption of oleate ions with Ca{sup 2+} on powellite lattice or the precipitation of calcium dioleate agglomerates on powellite surface when it was in the solution without or with Ca{sup 2+}, respectively. The FTIR measurements further confirm the chemisorption of oleate ions with Ca{sup 2+} active sites on powellite surface.

The adsorption of oleate on powellite and fluorapatite: A joint experimental and theoretical simulation study

International Nuclear Information System (INIS)

Zhen, Wang

2017-01-01

Highlights: • Flotation of powellite from fluorapatite at pH 2–7 using 50–80 mg/L sodium oleate can be achieved. • Oleate chemisorbs on powellite by interaction of carboxylate group with lattice Ca atoms. • Calcium dioleate precipitates can also adsorb on powellite surface. - Abstract: Flotation and adsorption performance of sodium oleate(NaOl)on powellite and fluorapatite were investigated in this work through micro-flotation tests, work of adhesion calculations, molecular dynamics simulation, micro-topography studies and FTIR measurements. The micro-flotation results show a similar flotation behaviors of powellite and fluorapatite under alkaline conditions, but a considerable difference in mineral recoveries in the pH range 2–7, which demonstrates the possibilities for separating powillite from fluorapatite under acidic conditions. The great difference in mineral recovery displays a good accordance with the obvious difference in the work of adhesion of powellite and fluorapatite at NaOl dosage range of 40–80 mg/L, obtained from flotation and contact angle measurements, respectively. The more negative interaction energy (ΔE) between NaOl and powellite/water interface from molecular dynamics simulation reveals a more easily adsorption of NaOl onto powellite than onto fluorapatite, which excellently matches with the results of flotation and work of adhesion. The results of micro-topography study shows that the adsorption of NaOl on powellite is mainly ascribed to the chemisorption of oleate ions with Ca"2"+ on powellite lattice or the precipitation of calcium dioleate agglomerates on powellite surface when it was in the solution without or with Ca"2"+, respectively. The FTIR measurements further confirm the chemisorption of oleate ions with Ca"2"+ active sites on powellite surface.

Water-Stable Metal-Organic Framework with Three Hydrogen-Bond Acceptors: Versatile Theoretical and Experimental Insights into Adsorption Ability and Thermo-Hydrolytic Stability.

Science.gov (United States)

Roztocki, Kornel; Lupa, Magdalena; Sławek, Andrzej; Makowski, Wacław; Senkovska, Irena; Kaskel, Stefan; Matoga, Dariusz

2018-03-19

A new microporous cadmium metal-organic framework was synthesized both mechanochemically and in solution by using a sulfonyl-functionalized dicarboxylate linker and an acylhydrazone colinker. The three-dimensional framework is highly stable upon heating to 300 °C as well as in aqueous solutions at elevated temperatures or acidic conditions. The thermally activated material exhibits steep water vapor uptake at low relative pressures at 298 K and excellent recyclability up to 260 °C as confirmed by both quasi-equilibrated temperature-programmed desorption and adsorption (QE-TPDA) method as well as adsorption isotherm measurements. Reversible isotherms and hysteretic isobars recorded for the desorption-adsorption cycles indicate the maximum uptake of 0.19 g/g (at 298 K, up to p/p 0 = 1) or 0.18 g/g (at 1 bar, within 295-375 K range), respectively. The experimental isosteric heat of adsorption (48.9 kJ/mol) indicates noncoordinative interactions of water molecules with the framework. Exchange of the solvent molecules in the as-made material with water, performed in the single-crystal to single-crystal manner, allows direct comparison of both X-ray crystal structures. The single-crystal X-ray diffraction for the water-loaded framework demonstrates the orientation of water clusters in the framework cavities and reveals their strong hydrogen bonding with sulfonyl, acyl, and carboxylate groups of the two linkers. The grand canonical Monte Carlo (GCMC) simulations of H 2 O adsorption corroborate the experimental findings and reveal preferable locations of guest molecules in the framework voids at various pressures. Additionally, both experimental and GCMC simulation insights into the adsorption of CO 2 (at 195 K) on the activated framework are presented.

[Treatment of organic waste gas by adsorption rotor].

Science.gov (United States)

Zhu, Run-Ye; Zheng, Liang-Wei; Mao, Yu-Bo; Wang, Jia-De

2013-12-01

The adsorption rotor is applicable to treating organic waste gases with low concentration and high air volume. The performance of adsorption rotor for purifying organic waste gases was investigated in this paper. Toluene was selected as the simulative gaseous pollutant and the adsorption rotor was packed with honeycomb modified 13X molecular sieves (M-13X). Experimental results of the fixed adsorption and the rotor adsorption were analyzed and compared. The results indicated that some information on the fixed adsorption was useful for the rotor adsorption. Integrating the characteristics of the adsorbents, waste gases and the structures of the rotor adsorption, the formulas on optimal rotor speed and cycle removal efficiency of the adsorption rotor were deduced, based on the mass and heat balances of the adsorbing process. The numerical results were in good agreement with the experimental data, which meant that the formulas on optimal rotor speed and cycle removal efficiency could be effectively applied in design and operation of the adsorption rotor.

Numerical evaluation of Cs adsorption in PB column by extended Langmuir formula and one-dimensional adsorption model

International Nuclear Information System (INIS)

Hiroshi Ogawa; Akiko Kitajima; Hisashi Tanaka; Tohru Kawamoto

2015-01-01

Adsorption property of granulated Prussian blue adsorbent on radioactive cesium was evaluated for efficient decontamination in Fukushima area. The adsorbent was found to show an inflective adsorption isotherm, which was expressed by extended Langmuir formula with three adsorption sites. Adsorption speeds of each site were evaluated by time-dependent batch experiment. The simulation using derived parameters and one-dimensional adsorption model successfully reproduced the experimental data of cesium decontamination by small and large columns. (author)

Inhibition of mild steel corrosion in acid solution by Pheniramine drug: Experimental and theoretical study

Energy Technology Data Exchange (ETDEWEB)

Ahamad, Ishtiaque [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221 005 (India); Prasad, Rajendra [Department of Chemistry, SGB Amravati University, Amravati 444 602 (India); Quraishi, M.A., E-mail: maquraishi@rediffmail.co [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221 005 (India)

2010-09-15

Inhibition of mild steel corrosion in 1 M HCl solution by Pheniramine drug was studied using weight loss, electrochemical impedance spectroscopy, linear polarization resistance, and potentiodynamic polarization measurements. The values of activation energy (E{sub a}) and different thermodynamic parameters such as adsorption equilibrium constant (K{sub ads}), free energy of adsorption ({Delta}G{sub ads}{sup o}), adsorption enthalpy ({Delta}H{sub ads}{sup o}) and adsorption entropy ({Delta}S{sub ads}{sup o}) were calculated and discussed. The adsorption process of studied drug on mild steel surface obeys the Langmuir adsorption isotherm. Potentiodynamic polarization measurements showed that Pheniramine is mixed-type inhibitor. Further, theoretical calculations were carried out and relations between computed parameters and experimental inhibition efficiency were discussed.

Measurement and analysis of adsorption isotherms of CO_2 on activated carbon

International Nuclear Information System (INIS)

Singh, Vinod Kumar; Anil Kumar, E.

2016-01-01

In the present work CO_2 adsorption isotherms of a commercially available activated carbon, Norit Darco type obtained from lignite granular material, were measured. Adsorption isotherms were measured at different temperatures 298 K, 308 K, 318 K and 338 K and over a pressure range of 0–45 bar using Sievert's type experimental setup. Experimental data of CO_2 adsorption isotherms were modelled using Langmuir and Dubinin–Astakhov (D–A) isotherm models. Based on coefficient of correlation and normalized standard deviation it was found that D–A isotherm model was well suited with the experimental data of CO_2 adsorption isotherms. The important thermodynamic properties viz., limiting heat of adsorption at zero coverage, entropy, Gibbs free energy and isosteric heat of adsorption as a function of surface coverage were evaluated using van't Hoff and Clausius–Clapeyron equations. These thermodynamic properties were indicating that CO_2 uptake by activated carbon is a physisorption phenomenon. The adsorption isotherms data and the thermodynamic parameters estimated in the present study are useful for designing of an adsorption based gas storage systems.

Simulations and experimental investigations of the competitive adsorption of CH4 and CO2 on low-rank coal vitrinite.

Science.gov (United States)

Yu, Song; Bo, Jiang; Jiahong, Li

2017-09-16

The mechanism for the competitive adsorption of CH 4 and CO 2 on coal vitrinite (DV-8, maximum vitrinite reflectance R o,max  = 0.58%) was revealed through simulation and experimental methods. A saturated state was reached after absorbing 17 CH 4 or 22 CO 2 molecules per DV-8 molecule. The functional groups (FGs) on the surface of the vitrinite can be ranked in order of decreasing CH 4 and CO 2 adsorption ability as follows: [-CH 3 ] > [-C=O] > [-C-O-C-] > [-COOH] and [-C-O-C-] > [-C=O] > [-CH 3 ] > [-COOH]. CH 4 and CO 2 distributed as aggregations and they were both adsorbed at the same sites on vitrinite, indicating that CO 2 can replace CH 4 by occupying the main adsorption sites for CH 4 -vitrinite. High temperatures are not conducive to the adsorption of CH 4 and CO 2 on vitrinite. According to the results of density functional theory (DFT) and grand canonical Monte Carlo (GCMC) calculations, vitrinite has a higher adsorption capacity for CO 2 than for CH 4 , regardless of whether a single-component or binary adsorbate is considered. The equivalent adsorption heat (EAH) of CO 2 -vitrinite (23.02-23.17) is higher than that of CH 4 -vitrinite (9.04-9.40 kJ/mol). The EAH of CO 2 -vitrinite decreases more rapidly with increasing temperature than the EAH of CH 4 -vitrinite does, indicating in turn that the CO 2 -vitrinite bond weakens more quickly with increasing temperature than the CH 4 -vitrinite bond does. Simulation data were found to be in good accord with the corresponding experimental results.

Laboratory studies on the adsorption kinetics of 137Cs in sediment

International Nuclear Information System (INIS)

Jaison, T.J.; Patra, A.K.; Ravi, P.M.; Sarkar, P.K.

2012-01-01

During the operation of a nuclear reactor, extreme care is taken to minimize the release of radionuclides to the environment. Low level radioactive liquid waste generated is treated and released to the nearest water body after monitoring to ensure that the activity levels are well within the regulatory limits. Environmental Survey Laboratories (ESL) attached to power plants carry out a systematic environmental monitoring and impact assessment to ensure that the dose to the member of public is well within the limits. This paper presents the results of a systematic laboratory study carried out at ESL, Kakrapar Atomic Power Station (KAPS) on the adsorption kinetics of 137 Cs in sediment. The study is to evaluate the sorption kinetics of 137 Cs + onto site specific sediment. Sets of adsorption experiments were conducted at specific time intervals for two different 137 Cs + concentrations, keeping other experimental conditions same. The kinetics of 137 Cs + adsorption on sediment is analyzed using pseudo first order, pseudo second order, and intra-particle diffusion kinetic models. The pseudo-second order kinetic model is better correlated with the kinetics data compared with the pseudo first-order model. This indicates 137 Cs + ions can be involved in chemical bonding during the adsorption process to the analysed sediment. This chemi-sorption processes show a good compliance with the pseudo-second order kinetic model. It is also evident that lower concentration exhibits greater adsorption rate (k 2 value is 1.85 x 10 -5 Bq g -1 min -1 for 1245 Bq sets and 1.05 x 10 -5 Bq g -1 min -1 for 2456 Bq sets) from the pseudo second order model. Intra-particle diffusion rate constants (K id ) were also obtained by two different models for both the concentrations and found to be higher for higher concentration. (author)

Study on the adsorption performance of composite adsorbent of CaCl2 and expanded graphite with ammonia as adsorbate

International Nuclear Information System (INIS)

Li, S.L.; Wu, J.Y.; Xia, Z.Z.; Wang, R.Z.

2009-01-01

A novel constant volume test unit was built to study the adsorption performance of a new type composite adsorbent. This test unit can measure the adsorption isosteres of the working pairs. The adsorption isosteres are the curves of the adsorption pressure variation with the adsorption temperatures at constant adsorption quantities. Compared to the former test results of isothermals and isobars, the isosteres are better for the calculation of the adsorption heat, desorption heat and the selection the adsorption working pairs. Three experimental results were obtained: the first result was that the expanded graphite powders were superior to the expandable graphite powders to facilitate the transportation of working fluid in the composite adsorbent. The second one was that the composite adsorbent treated by solution is more homogeneous than the simple mixed composite adsorbent and the treated composite adsorbent has a better mass transfer performance. The last one was that the adsorption isosteres was the same one not only in the heating process but also in the cooling process and this performance was not relevant to the homogeneity of the composite adsorbent

Adsorption kinetics, isotherm, and thermodynamics studies of acetyl-11-keto-β-boswellic acids (AKBA) from Boswellia serrata extract using macroporous resin.

Science.gov (United States)

Niphadkar, Sonali S; Rathod, Virendra K

2017-09-14

An acetyl-11-keto-β-boswellic acid (AKBA) is potent anti-inflammatory agent found in Boswellia serrata oleogum resin. Adsorption characteristics of AKBA from B. serrata were studied using macroporous adsorbent resin to understand separation and adsorption mechanism of targeted molecules. Different macroporous resins were screened for adsorption and desorption of AKBA and Indion 830 was screened as it showed higher adsorption capacity. The kinetic equations were studied and results showed that the adsorption of AKBA on Indion 830 was well fitted to the pseudo first-order kinetic model. The influence of two parameters such as temperature (298, 303, and 308 K) and pH (5-8) on the adsorption process was also studied. The experimental data was further investigated using Langmuir, Freundlich, and Temkin isotherm models. It was observed that Langmuir isotherm model was found to be the best fit for AKBA adsorption by Indion 830 and highest adsorption capacity (50.34 mg/g) was obtained at temperature of 303 K. The values of thermodynamic parameters such as the change of Gibbs free energy (ΔG*), entropy (ΔS*), and enthalpy (ΔH*), indicated that the process of adsorption was spontaneous, favourable, and exothermic.

First-principles study of the alkali earth metal atoms adsorption on graphene

International Nuclear Information System (INIS)

Sun, Minglei; Tang, Wencheng; Ren, Qingqiang; Wang, Sake; JinYu; Du, Yanhui; Zhang, Yajun

2015-01-01

Graphical abstract: - Highlights: • The adsorption of Be and Mg adatoms on graphene is physisorption. • Ca, Sr, and Ba adatoms bond ionically to graphene and the most stable adsorption site for them is hollow site. • The zero band gap semiconductor graphene becomes metallic and magnetic after the adsorption of Ca, Sr, and Ba adatoms. - Abstract: Geometries, electronic structures, and magnetic properties for alkali earth metal atoms absorbed graphene have been studied by first-principle calculations. For Be and Mg atoms, the interactions between the adatom and graphene are weak van der Waals interactions. In comparison, Ca, Sr and Ba atoms adsorption on graphene exhibits strong ionic bonding with graphene. We found that these atoms bond to graphene at the hollow site with a significant binding energy and large electron transfer. It is intriguing that these adatoms may induce important changes in both the electronic and magnetic properties of graphene. Semimetal graphene becomes metallic and magnetic due to n-type doping. Detailed analysis shows that the s orbitals of these adatoms should be responsible for the arising of the magnetic moment. We believe that our results are suitable for experimental exploration and useful for graphene-based nanoelectronic and data storage.

First-principles study of the alkali earth metal atoms adsorption on graphene

Energy Technology Data Exchange (ETDEWEB)

Sun, Minglei [School of Mechanical Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Tang, Wencheng, E-mail: 101000185@seu.edu.cn [School of Mechanical Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Ren, Qingqiang [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, Hunan (China); Wang, Sake [Department of Physics, Southeast University, Nanjing 210096, Jiangsu (China); JinYu [School of Materials Science and Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Jiangsu Key Laboratory of Advanced Metallic Materials, Southeast University, Nanjing 211189, Jiangsu (China); Du, Yanhui [School of Mechanical Engineering, Southeast University, Nanjing 211189, Jiangsu (China); Zhang, Yajun [Department of Engineering Mechanics, School of Aeronautics and Astronautics, Zhejiang University, Hangzhou 310027, Zhejiang (China)

2015-11-30

Graphical abstract: - Highlights: • The adsorption of Be and Mg adatoms on graphene is physisorption. • Ca, Sr, and Ba adatoms bond ionically to graphene and the most stable adsorption site for them is hollow site. • The zero band gap semiconductor graphene becomes metallic and magnetic after the adsorption of Ca, Sr, and Ba adatoms. - Abstract: Geometries, electronic structures, and magnetic properties for alkali earth metal atoms absorbed graphene have been studied by first-principle calculations. For Be and Mg atoms, the interactions between the adatom and graphene are weak van der Waals interactions. In comparison, Ca, Sr and Ba atoms adsorption on graphene exhibits strong ionic bonding with graphene. We found that these atoms bond to graphene at the hollow site with a significant binding energy and large electron transfer. It is intriguing that these adatoms may induce important changes in both the electronic and magnetic properties of graphene. Semimetal graphene becomes metallic and magnetic due to n-type doping. Detailed analysis shows that the s orbitals of these adatoms should be responsible for the arising of the magnetic moment. We believe that our results are suitable for experimental exploration and useful for graphene-based nanoelectronic and data storage.

Glycolate adsorption at gold and platinum electrodes: A theoretical and in situ spectroelectrochemical study

International Nuclear Information System (INIS)

Delgado, Jose Manuel; Blanco, Raquel; Orts, Jose Manuel; Perez, Juan Manuel; Rodes, Antonio

2010-01-01

The adsorption of glycolate anions at sputtered gold thin-film electrodes was studied in perchloric acid solutions by cyclic voltammetry experiments combined with in situ Surface Enhanced Raman Scattering (SERS) and Surface Enhanced Infrared Reflection Absorption Spectroscopy under attenuated total reflection conditions (ATR-SEIRAS). Theoretical harmonic vibrational frequencies and band intensities obtained from B3LYP/LANL2DZ,6-31+G(d) calculations for glycolate species adsorbed on Au clusters with (1 1 1) orientation were used to interpret the experimental spectra. Vibrational data confirm the bidentate bonding of glycolate anions through the oxygen atoms of the carboxylate group, in a bridge configuration with the OCO plane perpendicular to the metal surface. The DFT calculations show no significant effect of the total charge of the metal cluster-adsorbate adduct on the vibrational frequencies of adsorbed glycolate species. The infrared experimental study is extended to platinum films electrochemically deposited onto sputtered gold thin-film electrodes showing the potential-dependent formation of adsorbed CO upon dissociative adsorption of glycolate anions. As in the case of gold, the reversible adsorption of glycolate anions takes place in a bidentate configuration as predicted by DFT calculations for glycolate adsorbed on Pt(1 1 1) clusters. At low glycolic acid concentration, the in situ ATR-SEIRA spectra evidence the formation of adsorbed oxalate as reaction intermediate.

Adsorption Behavior of Uranium and Mechanism Analysis on Banyan Leaves

International Nuclear Information System (INIS)

Xia Liangshu; Tan Kaixuan; Wang Xiao; Zheng Weina

2010-01-01

The adsorption behavior of uranium on banyan leaves was studied with static experiments. The adsorption process was analyzed in terms of thermodynamics and kinetics, and the adsorption mechanism was analyzed with FTIR and SEM. In the studied condition, the equilibrium adsorption data fit to Freundlich isotherms, with a relation coefficient greater than 0.99. The adsorption of uranium on banyan leaves is an endothermic process. Kinetic analysis shows that the adsorption rate is mainly controlled by surface adsorption. The process of adsorption can be described by an equation of Pseudo 2nd-order model. The calculation data are in good agreement with the experimental data,and the relation coefficient is 0.9998. The thermodynamic data indicate that the synergistic uranium biosorption by banyan leaves is a spontaneous and endothermal adsorption process. The adsorption of uranium on banyan leaves changes the cell's surface form of banyan leaves.In the adsorption process, UO 2 2+ mainly chelates with -OH,C=O,P-O and Si=O etc. on the cell's surface and forms the complexes. The adsorption of uranium should be of surface coordination. (authors)

Experimental probe into adsorption of Sr, Cs in the Soil

International Nuclear Information System (INIS)

Yuan Guangyu; Bai Qingzhong

1987-12-01

There are some obstacles in researching on the adsorption patterns of Sr and Cs in soil. One of them is that it is difficult to compare and to consult between various results and data for different types and sizes of soil. For this reason, it is neccesary to do further research into adsorption patterns of Sr and Cs in single particles of soil. By using scanning electromicroscope, the microcosmic phenomena of nuclides adsorption is observed, and a possible mechanism is proposed. A certain amount of diluvial soil from Shanxi Province and a certain amount of alluvial soil from western Beijing suburban were chosen as detected samples. After determining the distributions of adsorbed Sr and Cs in varied mineral particles, it is pointed out that the defference of chemical components of various size soils effects Kd value of Sr and Cs obviously. The method for calculating Kd value of mixing samples according to the particle distribution coefficients are derived under the condition of surface adsorption as main. The authors expound that it is favourable for accuracy to select and control the particle sizes in static adsorptional experiment

A DFT study on benzene adsorption over tungsten sulfides: surface model and adsorption geometries

NARCIS (Netherlands)

Koide, R.; Hensen, E.J.M.; Paul, J.F.; Cristol, S.; Payen, E.; Nakamura, H.; Santen, van R.A.

2007-01-01

Benzene adsorption on a WS2(100) surface was studied by ab initio periodic DFT computations. Benzene adsorption is facile on the bridge site of the bare W edge via ¿2 or ¿3 coordination. Taking into account the stable configuration at the W edge under typical hydrotreating reaction conditions (623

STUDIES OF ACTIVATION OF GALENA BY COPPER AND XANTHATE (PIPX SYNTHESIZED COLLECTORS ADSORPTION

Directory of Open Access Journals (Sweden)

Z. NEDJAR

2015-07-01

Full Text Available In this study, we suggest proceeding to an experimental study concerning the synthesis of new organo metallic product xanthate (PIPX by intermittent method and their use in the processes of sulphides flotation. Flotation of sulphide minerals and their activation and modification have been investigated for many years. In this work the influence of sulphite on xanthate-induced flotation of copper-activated galena has been studied been investigated. The adsorption of potassium isopropyl xanthate (PIPX 3⋅10-3M on galena has been also studied using electrochemical potential, FTIR spectra and SEM. Galena activated with copper sulfate (10-4 M have been investigated at pH = 9. Surface species have been identified and correlated with SEM. After copper sulfate activation, copper xanthate exists on all of the minerals studied. Basic pH is most favorable for potassium isopropyl xanthate adsorption on activated minerals.

Experimental study and modelling of competitive adsorption equilibria of aromatics in liquid phase on X and Y faujasites; Etude experimentale et modelisation des equilibres d'adsorption competitive d'aromatiques en phase liquide sur des faujasites X et Y

Energy Technology Data Exchange (ETDEWEB)

Tournier, H.

2000-10-13

The separation of p-xylene from C{sub 8} aromatics is performed industrially by selective adsorption on zeolitic molecular sieves. The aim of this work is to study and model adsorption equilibria of C{sub 8} and C{sub 10} aromatics on X and Y zeolites. The experimental data are obtained by an entirely automated equipment allowing to work in a large range of temperature (50 deg. C - 250 deg. C). With this equipment, we can follow the evolution of the composition of the liquid phase and determine the composition of the adsorbed phase at equilibrium by a mass balance calculation and with an inert component. Two analytical techniques are used to determine the composition of the liquid phase: (1) a classical method using a gas chromatograph (GC) allowed to measure selectivities in the concentration range (3%-97%) in a component; (2) an original method based on the use and on the measure of {sup 13}C labelled xylenes was developed to investigate the ranges of strongly contrasting concentrations [0-3%] and [97%-100%] in a component, which are representative of high purity domains. Lastly, three thermodynamic models are used to describe the adsorption equilibria: the Langmuir-Freundlich model, the quasi-chemical model and the statistical model. The last model is the more interesting, because it is based on physical considerations. A new statistical model has been developed with taking into account some observations coming from adsorption phenomenon in zeolites. (author)

WATER ADSORPTION AND DESORPTION ISOTHERMS ON MILK POWDER: II. WHOLE MILK

Directory of Open Access Journals (Sweden)

Edgar M. Soteras

2014-03-01

Full Text Available The aim of this research was the determination of adsorption and desorption isotherms of cow whole milk powder. The experiments have been carried out at 15, 25 and 40 ºC, in ranges of moisture and water activity characteristic of normal conditions in which the processes of drying, packaging and storage are developed. By studying the influence of the temperature on the experimental plots, the isosteric adsorption heat was determined. Experimental data were correlated to the referential model of Guggenheim, Anderson and Boer (GAB. For both, adsorption and desorption, a good model fit was observed. The isotherms showed very similar shapes between them and, by comparing adsorption and desorption isotherms, the phenomenon of hysteresis was confirmed.

Multicomponent Adsorption Model for Polar and Associating Mixtures

DEFF Research Database (Denmark)

Nesterov, Igor; Shapiro, Alexander; Kontogeorgis, Georgios M.

2015-01-01

of these problems could be due to the fact that the original MPTA assumes that a given adsorbent has the same adsorption capacity (for example, porous volume) for all the adsorbed substances and is adjusted simultaneously to many data. This is a simplified picture, as experimental data indicate that the adsorption......-Radushkevich-Astakhov potentials and the potentials directly restored from experimental data by solving the inverse problem. Application of the latter potentials Clearly demonstrates the importance of the difference in adsorption capacities. However, the quality of prediction of binary adsorption is similar for both potentials...

Adsorption Studies for Arsenic Removal Using Activated Moringa oleifera

Directory of Open Access Journals (Sweden)

T. Sumathi

2014-01-01

Full Text Available A new low cost adsorbent, activated Moringa oleifera has been developed for aqueous arsenic removal. Batch experiments were revealed that As removal was up to 71.3% using activated Moringa oleifera. Kinetics studies revealed that Langmuir isotherm was followed with a better correlation than the Freundlich isotherm. The thermodynamic parameters such as ΔH, ΔS, and ΔG were computed from the experimental data. These values show that the adsorption is endothermic and spontaneous in nature. Thus, this recently developed cost-effective novel biosorbent, activated Moringa oleifera can be used as household level to mitigate the arsenic problem.

MODELLING OF KINETICS OF FLUORINE ADSORPTION ONTO MODIFIED DIATOMITE

Directory of Open Access Journals (Sweden)

VEACESLAV ZELENTSOV

2017-03-01

Full Text Available The paper presents kinetics modelling of adsorption of fluorine onto modified diatomite, its fundamental characteristics and mathematical derivations. Three models of defluoridation kinetics were used to fit the experimental results on adsorption fluorine onto diatomite: the pseudo-first order model Lagergren, the pseudo-second order model G. McKay and H.S. Ho and intraparticle diffusion model of W.J. Weber and J.C. Morris. Kinetics studies revealed that the adsorption of fluorine followed second-order rate model, complimented by intraparticle diffusion kinetics. The adsorption mechanism of fluorine involved three stages – external surface adsorption, intraparticle diffusion and the stage of equilibrium.

Kinetics and equilibrium study for the adsorption of textile dyes on coconut shell activated carbon

Directory of Open Access Journals (Sweden)

Aseel M. Aljeboree

2017-05-01

Full Text Available The preparation of activated carbon from coconut husk with H2SO4 activation (CSAC and its ability to remove textile dyes (maxilon blue GRL, and direct yellow DY 12, from aqueous solutions were reported in this study. The adsorbent was characterized with Fourier transform infrared spectrophotometer (FT-IR, and scanning electron microscope (SEM. Various physiochemical parameters such as, contact time, initial dye concentration, adsorbent dosage, particle size, pH of dye solution and temperature were investigated in a batch-adsorption technique. Result showed that the adsorption of both GRL and DY 12 dyes was favorable at acidic pH. The adsorption uptake was found to increase with increase in initial dye concentration, and contact time but decreases with the amount of adsorbent, particle size, and temperature of the system. The chemisorption, intra-particle diffuse, pseudo-first-order and pseudo-second-order kinetic models were applied to test the experimental data. The pseudo-second order exhibited the best fit for the kinetic studies, which indicates that adsorption of (GRL, and DY 12 is limited by chemisorption process. The equilibrium data were evaluated using Langmuir, Freundlich, Temkin and Fritz–Schlunder isotherms. The Fritz–Schlunder model best describes the uptake of (GRL and DY 12 dye, which implies that the adsorption of textiles dyes in this study onto coconut husk activated carbon is heterogeneous with multi-layers. Thermodynamic parameters such as Gibbs free energy, enthalpy and entropy were determined. It was found that (GRL and DY 12 dye adsorption was spontaneous and endothermic.

Kinetics of a gas adsorption compressor

Science.gov (United States)

Chan, C. K.; Tward, E.; Elleman, D. D.

1984-01-01

Chan (1981) has suggested that a process based on gas adsorption could be used as a means to drive a Joule-Thomson (J-T) device. The resulting system has several advantages. It is heat powered, it has no sealing, there are no mechanical moving parts, and no active control is required. In the present investigation, a two-phase model is used to analyze the transients of a gas adsorption compressor. The modeling of the adsorption process is based on a consideration of complete thermal and mechanical equilibrium between the gaseous phase and the adsorbed gas phase. The experimental arrangement for two sets of kinetic tests is discussed, and data regarding the experimental results are presented in graphs. For a theoretical study, a two-phase model was developed to predict the transient behavior of the compressor. A computer code was written to solve the governing equations with the aid of a standard forward marching predictor-corrector method.

CO2 adsorption using TiO2 composite polymeric membranes: A kinetic study.

Science.gov (United States)

Hafeez, Sarah; Fan, X; Hussain, Arshad; Martín, C F

2015-09-01

CO2 is the main greenhouse gas which causes global climatic changes on larger scale. Many techniques have been utilised to capture CO2. Membrane gas separation is a fast growing CO2 capture technique, particularly gas separation by composite membranes. The separation of CO2 by a membrane is not just a process to physically sieve out of CO2 through the controlled membrane pore size. It mainly depends upon diffusion and solubility of gases, particularly for composite dense membranes. The blended components in composite membranes have a high capability to adsorb CO2. The adsorption kinetics of the gases may directly affect diffusion and solubility. In this study, we have investigated the adsorption behaviour of CO2 in pure and composite membranes to explore the complete understanding of diffusion and solubility of CO2 through membranes. Pure cellulose acetate (CA) and cellulose acetate-titania nanoparticle (CA-TiO2) composite membranes were fabricated and characterised using SEM and FTIR analysis. The results indicated that the blended CA-TiO2 membrane adsorbed more quantity of CO2 gas as compared to pure CA membrane. The high CO2 adsorption capacity may enhance the diffusion and solubility of CO2 in the CA-TiO2 composite membrane, which results in a better CO2 separation. The experimental data was modelled by Pseudo first-order, pseudo second order and intra particle diffusion models. According to correlation factor R(2), the Pseudo second order model was fitted well with experimental data. The intra particle diffusion model revealed that adsorption in dense membranes was not solely consisting of intra particle diffusion. Copyright © 2015. Published by Elsevier B.V.

Experimental tests for FE(2.) and M(2.) removal from contaminated groundwater by adsorption: a comparison between activated carbon and pine bark

International Nuclear Information System (INIS)

Boni, M.R.; Sbaffoni, S.; Tedesco, P.

2009-01-01

In this paper a study on the adsorption process by activated carbon and pine bark is presented; the experimental activity aimed at comparing the performances of these two reactive materials in terms of removal efficiency and adsorption capacity. Moreover, the environmental compatibility of both materials was checked for their possible use as reactive media in a permeable reactive barrier for the in situ treatment of contaminated groundwater. Thus batch tests were carried out with a liquid-to-solid ratio equal to 10 1 kg; three different iron and manganese, alone and mixed, concentrations (100, 1000 e 10000 μg l-1) and different particle size distributions ( [it

Removal of phenol from aqueous solutions by adsorption onto organomodified Tirebolu bentonite: Equilibrium, kinetic and thermodynamic study

Energy Technology Data Exchange (ETDEWEB)

Senturk, Hasan Basri; Ozdes, Duygu; Gundogdu, Ali; Duran, Celal [Department of Chemistry, Karadeniz Technical University, Faculty of Arts and Sciences, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Department of Chemistry, Erciyes University, Faculty of Arts and Sciences, 38039 Kayseri (Turkey)

2009-12-15

A natural bentonite modified with a cationic surfactant, cetyl trimethylammonium bromide (CTAB), was used as an adsorbent for removal of phenol from aqueous solutions. The natural and modified bentonites (organobentonite) were characterized with some instrumental techniques (FTIR, XRD and SEM). Adsorption studies were performed in a batch system, and the effects of various experimental parameters such as solution pH, contact time, initial phenol concentration, organobentonite concentration, and temperature, etc. were evaluated upon the phenol adsorption onto organobentonite. Maximum phenol removal was observed at pH 9.0. Equilibrium was attained after contact of 1 h only. The adsorption isotherms were described by Langmuir and Freundlich isotherm models, and both model fitted well. The monolayer adsorption capacity of organobentonite was found to be 333 mg g{sup -1}. Desorption of phenol from the loaded adsorbent was achieved by using 20% acetone solution. The kinetic studies indicated that the adsorption process was best described by the pseudo-second-order kinetics (R{sup 2} > 0.99). Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) were also calculated. These parameters indicated that adsorption of phenol onto organobentonite was feasible, spontaneous and exothermic in the temperature range of 0-40 {sup o}C.

Removal of phenol from aqueous solutions by adsorption onto organomodified Tirebolu bentonite: Equilibrium, kinetic and thermodynamic study

International Nuclear Information System (INIS)

Senturk, Hasan Basri; Ozdes, Duygu; Gundogdu, Ali; Duran, Celal; Soylak, Mustafa

2009-01-01

A natural bentonite modified with a cationic surfactant, cetyl trimethylammonium bromide (CTAB), was used as an adsorbent for removal of phenol from aqueous solutions. The natural and modified bentonites (organobentonite) were characterized with some instrumental techniques (FTIR, XRD and SEM). Adsorption studies were performed in a batch system, and the effects of various experimental parameters such as solution pH, contact time, initial phenol concentration, organobentonite concentration, and temperature, etc. were evaluated upon the phenol adsorption onto organobentonite. Maximum phenol removal was observed at pH 9.0. Equilibrium was attained after contact of 1 h only. The adsorption isotherms were described by Langmuir and Freundlich isotherm models, and both model fitted well. The monolayer adsorption capacity of organobentonite was found to be 333 mg g -1 . Desorption of phenol from the loaded adsorbent was achieved by using 20% acetone solution. The kinetic studies indicated that the adsorption process was best described by the pseudo-second-order kinetics (R 2 > 0.99). Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) were also calculated. These parameters indicated that adsorption of phenol onto organobentonite was feasible, spontaneous and exothermic in the temperature range of 0-40 o C.

Critical analysis of adsorption data statistically

Science.gov (United States)

Kaushal, Achla; Singh, S. K.

2017-10-01

Experimental data can be presented, computed, and critically analysed in a different way using statistics. A variety of statistical tests are used to make decisions about the significance and validity of the experimental data. In the present study, adsorption was carried out to remove zinc ions from contaminated aqueous solution using mango leaf powder. The experimental data was analysed statistically by hypothesis testing applying t test, paired t test and Chi-square test to (a) test the optimum value of the process pH, (b) verify the success of experiment and (c) study the effect of adsorbent dose in zinc ion removal from aqueous solutions. Comparison of calculated and tabulated values of t and χ 2 showed the results in favour of the data collected from the experiment and this has been shown on probability charts. K value for Langmuir isotherm was 0.8582 and m value for Freundlich adsorption isotherm obtained was 0.725, both are mango leaf powder.

Adsorption Studies of Radish Leaf Powder

Directory of Open Access Journals (Sweden)

Ankita

2016-01-01

Full Text Available Radish leaves (Raphanus sativus powder fractions was subjected to moisture adsorption isotherms at different isothermal temperature conditions from 15-45°C with an equal interval of 10°C. The sorption data obtained in gravimetric static method under 0.11–0.90 water activity conditions were subjected for sorption isotherms and found to be typical sigmoid trend. Experimental data were assessed for the applicability in the prediction through sorption models fitting and found that Polynomial and GAB equations performed well over all fitted models in describing equilibrium moisture content – equilibrium relative humidity (EMC–ERH relationships for shelf stable dehydrated radish leaf powder, over the entire range of temperatures condition under study. The net isosteric heat of sorption, differential entropy and free energy were determined at different temperatures and their dependence was seen with respect to equilibrium moisture content.

Ni adsorption and Ni-Al LDH precipitation in a sandy aquifer: An experimental and mechanistic modeling study

NARCIS (Netherlands)

Regelink, I.C.; Temminghoff, E.J.M.

2011-01-01

Mining activities and industries have created nickel (Ni) contaminations in many parts of the world. The objective of this study is to increase our understanding of Ni adsorption and Nickel-Aluminium Layered Double Hydroxide (Ni-Al LDH) precipitation to reduce Ni mobility in a sandy soil aquifer. At

Current state in adsorption from multicomponent solutions of nonelectrolytes on solids

International Nuclear Information System (INIS)

Borowko, M.; Jaroniec, M.

1983-01-01

This paper surveys the research carried out on the adsorption from multicomponent liquid mixtures of nonelectrolytes on solids with emphasis on the work performed by the authors. The consistent theoretical treatment of adsorption from concentrated and dilute multicomponent solutions and its application to the liquid adsorption chromatography with the mixed mobile phase are presented. This treatment involved nonideality of the bulk and surface phases, energetic heterogeneity of the adsorbent surface and it may be extended to multilayer adsorption from solutions. The multicomponent liquid/solid adsorption systems, studied experimentally, are reviewed. Many of them have been examined by means of the equations derived for liquid adsorption on heterogeneous surfaces. These studies are summarized in this paper. Moreover, the model studies illustrating the influence of solution nonideality and adsorbent heterogeneity on the excess adsorption isotherms and the distribution coefficient are discussed. (orig.)

Equilibrium curve determination of HF adsorption by activated carbon

International Nuclear Information System (INIS)

Bahrami, H.; Safdari, S. J.; Mousavian, S. M. A.

2010-01-01

One of the byproducts of uranium enrichment industry is hydrogen fluoride gas. Due to the toxicity and corrosivity of the molecule, it has adverse effects on the environment and the process. Therefore, it must be removed by adsorption towers. The activated carbon is one of the proposed sorbent for the adsorption. Hydrogen fluoride adsorption equilibrium curve gives important information for designing the adsorption towers. In this article, the hydrogen fluoride adsorption and adsorption factors were determined experimentally, and four different types of carbon have been used. The operating pressure in all tests was less than 30 mbar. Comparison between the obtained experimental equilibrium curves shows that the first, second and fourth types of activated carbon are suitable for the adsorption of hydrogen fluoride. The experimental data were fitted using mathematical models of Langmuir, Freundlich, Toth and Henry. The results show that Toth mathematical model is more suitable than other models. Also, the absolute error were predicted by the model of Toth for the first, second and fourth types of the activated carbon were 12.9, 16.5 and 34 percent, respectively.

Competitive adsorption behaviors of carbon dioxide and n-dodecane mixtures in 13X molecular sieve

Science.gov (United States)

Zhu, Chaofan; Dong, Mingzhe; Gong, Houjian

2018-01-01

The CO2 cyclic injection has been proven to be effective to enhance tight oil recovery under constant reservoir temperature and down hole pressure conditions. However, the enhance tight oil recovery mechanism was unclear, especially the adsorption of the CO2 and alkane in the surface. Therefore, it is great important to study the adsorption mechanism of CO2 and alkane mixtures in tight oil. In this study, a new experimental method and apparatus have been designed to test the change of the mole fraction of CO2 and n-C12 before and after the adsorption equilibrium. Then, the adsorption amount of CO2 and n-C12 was obtained by a mathematical method. Moreover, the adsorption character of CO2 and n-C12 mixtures in 13X molecular sieve and the effect of pressure on the adsorption and amount were studied. The results show that the adsorption of CO2 and the desorption of n-C12 follow the Langmuir adsorption. This study provides a straightforward method to experimentally determine the adsorption properties of the tight oil, which can be used to evaluate enhanced tight oil recovery by CO2 injection.

Comparison of adsorption equilibrium models and error functions for the study of sulfate removal by calcium hydroxyapatite microfibrillated cellulose composite.

Science.gov (United States)

Hokkanen, Sanna; Bhatnagar, Amit; Koistinen, Ari; Kangas, Teija; Lassi, Ulla; Sillanpää, Mika

2018-04-01

In the present study, the adsorption of sulfates of sodium sulfate (Na 2 SO 4 ) and sodium lauryl sulfate (SLS) by calcium hydroxyapatite-modified microfibrillated cellulose was studied in the aqueous solution. The adsorbent was characterized using elemental analysis, Fourier transform infrared, scanning electron microscope and elemental analysis in order to gain the information on its structure and physico-chemical properties. The adsorption studies were conducted in batch mode. The effects of solution pH, contact time, the initial concentration of sulfate and the effect of competing anions were studied on the performance of synthesized adsorbent for sulfate removal. Adsorption kinetics indicated very fast adsorption rate for sulfate of both sources (Na 2 SO 4 and SLS) and the adsorption process was well described by the pseudo-second-order kinetic model. Experimental maximum adsorption capacities were found to be 34.53 mg g -1 for sulfates of SLS and 7.35 mg g -1 for sulfates of Na 2 SO 4. The equilibrium data were described by the Langmuir, Sips, Freundlich, Toth and Redlich-Peterson isotherm models using five different error functions.

An experimental study of furan adsorption and decomposition on vicinal palladium surfaces using scanning tunneling microscopy

Science.gov (United States)

Loui, A.; Chiang, S.

2018-04-01

The intact adsorption and decomposition of furan (C4H4O) on vicinal palladium surfaces with (111)-oriented terraces has been studied by scanning tunneling microscopy (STM) over a range of temperatures. STM images at 225 K show that furan molecules lie flat and prefer to adsorb at upper step edges. At 225 K, furan molecules adsorbed on "narrow" terraces of 20 to 45 Å in width appear to diffuse more readily than those adsorbed on "wide" terraces of 160 to 220 Å. A distinct population of smaller features appears in STM images on "narrow" terraces at 288 K and on "wide" terraces at 415 K and is identified with the C3H3 decomposition product, agreeing with prior studies which demonstrated that furan dissociates on Pd(111) to yield carbon monoxide (CO) and a C3H3 moiety in the 280 to 320 K range. Based on our direct visualization of this reaction using STM, we propose a spatial mechanism in which adsorption of furan at upper step edges allows catalysis of the dissociation, followed by diffusion of the product to lower step edges.

The removal of fluoride from aqueous solution by a lateritic soil adsorption: Kinetic and equilibrium studies.

Science.gov (United States)

Iriel, Analia; Bruneel, Stijn P; Schenone, Nahuel; Cirelli, Alicia Fernández

2018-03-01

The use of natural sorbents to remove fluoride from drinking water is a promising alternative because of its low-cost and easy implementation. In this article, fluoride adsorption on a latosol soil from Misiones province (Argentina) was studied regarding kinetic and equilibrium aspects. Experiments were conducted in batch at room temperature under controlled conditions of pH 4-8) and ionic strength (1-10mM KNO 3 ). Experimental data indicated that adsorption processes followed a PSO kinetic where initial rates have showed to be influenced by pH solution. The necessary time to reach an equilibrium state had resulted approximately 30min. Equilibrium adsorption studies were performed at pH 8 which is similar to the natural groundwater. For that, fluoride adsorption data were successfully adjusted to Dubinin-Ataskhov model determining that the fluoride adsorption onto soil particles mainly followed a physical mechanism with a removal capacity of 0.48mgg -1 . Finally, a natural groundwater was tested with laterite obtaining a reduction close to 30% from initial concentration and without changing significantly the physicochemical properties of the natural water. Therefore, it was concluded that the use of lateritic soils for fluoride removal is very promising on a domestic scale. Copyright © 2017 Elsevier Inc. All rights reserved.

Thermodynamic and topochemical aspects of the adsorption of some gaseous fluorides and solid fluorides

International Nuclear Information System (INIS)

Le Gressus, Claude

1968-01-01

This research thesis addresses the study of chemical adsorption. Such an adsorption is limited to a mono-molecular layer. As the Order Disorder Theory (ODT) allows adsorption isotherms to be calculated while taking interaction between adsorbed molecules into account, this research reports a comparison between the shape of experimental isotherms and that of theoretical isotherms. The knowledge of the involved phenomena is completed by the measurement of adsorption differential heats. After some generalities and a brief presentation of the ODT, the author presents experimental installations and techniques (micro-calorimeter, Mac-Bain balance), describes the adsorbent pre-treatment, reports the analysis performed by micro-sublimation, reports the study of the adsorption of hydrofluoric acid on CaF 2 , highlights the existence of different cases of energies increasing with the overlay rate, reports the detailed study of adsorption isotherms of ClF 3 and UF 6 on various solid fluorides. Results are finally interpreted and discussed

High pressure adsorption isotherms of nitrogen onto granular activated carbon for a single bed pressure swing adsorption refrigeration system

Science.gov (United States)

Palodkar, Avinash V.; Anupam, Kumar; Roy, Zunipa; Saha, B. B.; Halder, G. N.

2017-10-01

Adsorption characteristics of nitrogen onto granular activated carbon for the wide range of temperature (303-323 K) and pressure (0.2027-2.0265 MPa) have been reported for a single bed pressure swing adsorption refrigeration system. The experimental data were fitted to Langmuir, Dubinin-Astakhov and Dubinin-Radushkevich (D-R) isotherms. The Langmuir and D-R isotherm models were found appropriate in correlating experimental adsorption data with an average relative error of ±2.0541% and ±0.6659% respectively. The isosteric heat of adsorption data were estimated as a function of surface coverage of nitrogen and temperature using D-R isotherm. The heat of adsorption was observed to decrease from 12.65 to 6.98 kJ.mol-1 with an increase in surface concentration at 303 K and it followed the same pattern for other temperatures. It was found that an increase in temperature enhances the magnitude of the heat of adsorption.

Gas-phase formaldehyde adsorption isotherm studies on activated carbon: correlations of adsorption capacity to surface functional group density.

Science.gov (United States)

Carter, Ellison M; Katz, Lynn E; Speitel, Gerald E; Ramirez, David

2011-08-01

Formaldehyde (HCHO) adsorption isotherms were developed for the first time on three activated carbons representing one activated carbon fiber (ACF) cloth, one all-purpose granular activated carbon (GAC), and one GAC commercially promoted for gas-phase HCHO removal. The three activated carbons were evaluated for HCHO removal in the low-ppm(v) range and for water vapor adsorption from relative pressures of 0.1-0.9 at 26 °C where, according to the IUPAC isotherm classification system, the adsorption isotherms observed exhibited Type V behavior. A Type V adsorption isotherm model recently proposed by Qi and LeVan (Q-L) was selected to model the observed adsorption behavior because it reduces to a finite, nonzero limit at low partial pressures and it describes the entire range of adsorption considered in this study. The Q-L model was applied to a polar organic adsorbate to fit HCHO adsorption isotherms for the three activated carbons. The physical and chemical characteristics of the activated carbon surfaces were characterized using nitrogen adsorption isotherms, X-ray photoelectron spectroscopy (XPS), and Boehm titrations. At low concentrations, HCHO adsorption capacity was most strongly related to the density of basic surface functional groups (SFGs), while water vapor adsorption was most strongly influenced by the density of acidic SFGs.

Adsorption from solutions of non-electrolytes

CERN Document Server

Kipling, J J

1965-01-01

Adsorption from Solutions of Non-Electrolytes provides a general discussion of the subject, which has so far been given little or no attention in current textbooks of physical chemistry. A general view of the subject is particularly needed at a time when we wish to see how far it will be possible to use theories of solutions to explain the phenomena of adsorption. The book opens with an introductory chapter on the types of interface, aspects of adsorption from solution, types of adsorption, and classification of systems. This is followed by separate chapters on experimental methods, adsorption

Study on the adsorption of 233Pa in glass

International Nuclear Information System (INIS)

Natsumi, R.R.; Saiki, M.; Lima, F.W. de.

1982-08-01

It is intended to examine the adsorption of protactinium on glass in relation to pH, presence of complexing agents concentration and type of electrolytes. The study was made by using carrier-free 233 Pa solution and Pyrex glass tube was selected as adsorbent glass material surface. The adsorption curve of protactinium on glass surface as a function of the pH of the tracer solution showed the existence of two pronounced adsorption regions. It was found that this adsorption can be reduced by using electrolytes or complexing agents. Desorption of protactinium previously adsorbed on the Pyrex glass tube was also studied. Hidrochloric, oxalic and hydrofluoric acid solutions were used for the desorption experiments. (Author) [pt

Corrosion Inhibition and Adsorption Behavior of Clove Oil on Iron in Acidic Medium

Directory of Open Access Journals (Sweden)

Archana Saxena

2012-01-01

Full Text Available Corrosion behavior of iron in hydrochloric acid solution was studied using weight loss as well Scanning electron microscopy study without and with clove oil. The percentage inhibition efficiency increases with increasing clove oil concentration. All the data revel that the oil acts as an excellent inhibitor for the corrosion of iron in HCl solution. Thermodynamic, kinetic parameters and equilibrium constant for adsorption process were calculated from the experimental data. The adsorption of clove oil on experimental metals was found to follow the Langmuir adsorption isotherm at all the concentration studies. Scanning electron microscope (SEM, investigations also indicate that clove oil greatly lowers the dissolution currents.

Adsorption characteristics of green 5-arylaminomethylene pyrimidine-2,4,6-triones on mild steel surface in acidic medium: Experimental and computational approach

Science.gov (United States)

Verma, Chandrabhan; Olasunkanmi, Lukman O.; Ebenso, Eno E.; Quraishi, M. A.

2018-03-01

The effect of electron withdrawing nitro (-NO2) and electron releasing hydroxyl (-OH) groups on corrosion inhibition potentials of 5-arylaminomethylenepyrimidine-2,4,6-trione (AMP) had been studied. Four AMPs tagged AMP-1, AMP-2, AMP-3 and AMP-4 were studied for their ability to inhibit mild steel corrosion in 1 M HCl using experimental and theoretical methods. Gravimetric results showed that inhibition efficiency of the studied inhibitors increases with increasing concentration. The results further revealed that that electron withdrawing nitro (-NO2) group decreases the inhibition efficiency of AMP, while electron donating hydroxyl (-OH) group increases the inhibition efficiency of AMP. SEM and AFM studies showed that the studied compounds inhibit mild steel corrosion by adsorbing at the metal/electrolyte interface and their adsorption obeyed the Temkin adsorption isotherm. Potentiodynamic polarization study revealed that studied inhibitors act as mixed type inhibitors with predominant effect on cathodic reaction. The inhibitive strength of the compounds might have direct relationship electron donating ability of the molecules as revealed by quantum chemical parameters. The order of interaction energies derived from Monte Carlo simulations is AMP-4 > AMP-3 > AMP-2 > AMP-1, which is in agreement with the order of inhibition efficiencies obtained from experimental measurements.

Competitive Protein Adsorption - Multilayer Adsorption and Surface Induced Protein Aggregation

DEFF Research Database (Denmark)

Holmberg, Maria; Hou, Xiaolin

2009-01-01

In this study, competitive adsorption of albumin and IgG (immunoglobulin G) from human serum solutions and protein mixtures onto polymer surfaces is studied by means of radioactive labeling. By using two different radiolabels (125I and 131I), albumin and IgG adsorption to polymer surfaces...... is monitored simultaneously and the influence from the presence of other human serum proteins on albumin and IgG adsorption, as well as their mutual influence during adsorption processes, is investigated. Exploring protein adsorption by combining analysis of competitive adsorption from complex solutions...... of high concentration with investigation of single protein adsorption and interdependent adsorption between two specific proteins enables us to map protein adsorption sequences during competitive protein adsorption. Our study shows that proteins can adsorb in a multilayer fashion onto the polymer surfaces...

Silver-capped silicon nanopillar platforms for adsorption studies of folic acid using surface enhanced Raman spectroscopy and density functional theory

DEFF Research Database (Denmark)

Castillo, Jaime; Rindzevicius, Tomas; Wu, Kaiyu

2015-01-01

The study of the interactions of folic acid (FA) with surface enhanced Raman scattering substrates is relevant for understanding its adsorption mechanismand for fabricating analytical devices for detection ofmalignant cells over-expressing folate receptors. This paper presents a study of the adso......The study of the interactions of folic acid (FA) with surface enhanced Raman scattering substrates is relevant for understanding its adsorption mechanismand for fabricating analytical devices for detection ofmalignant cells over-expressing folate receptors. This paper presents a study...... of the adsorption of FA on silver-capped silicon nanopillar substrates employing surface enhanced Raman scattering spectroscopy and density functional theory calculations. The experimentally observed vibrations from free FA and FA bound to the Ag surface display different vibrational spectra indicating chemical...

Experimental analysis of an adsorptive cooling system with heat-regeneration; Analyse experimentale d'une machine frigorifique a adsorption a regeneration de chaleur

Energy Technology Data Exchange (ETDEWEB)

Szarzynski, St.

1998-07-01

For ecological reasons, the solid sorption systems applied to refrigeration or air conditioning are in a favourable context for their development. The aim of this work is to perform the experimental analysis of an adsorption refrigerating machinery which is based on a heat regeneration process (non-uniform temperature). Having a strong thermal gradient along the adsorber allows to increase the internal heat exchange and the performances of the system. An experimental device has been designed which uses this process. It is characterized by a new adsorbing composite, inserts inside the tubes and the use of a non-classical evaporator. An experimental analysis is performed which shows heat recovery factors greater than 0.5. The COP remains close to 0.4 whatever the refrigerant flow rate and the cycle length while PSF is easily greater than 100 W.kg{sup -1} of zeolite. The performances are mainly reduced by the thermal losses and by the important inert thermal masses inside the adsorber. In order to understand the operation of the adsorber, a numerical model integrating the distribution of heat losses and inert masses inside the adsorber has been used. The parameters of the model have been adjusted in order to fit with the experimental results. This model has permitted to predict the performances of the machine when the limiting factors are reduced. An analysis of the experimental setup according to the second principle of thermodynamics complete this study and shows the distribution of the different irreversibilities responsible for the weakness of the experimental performances. (J.S.)

Theoretical study of adsorption of water vapor on surface of metallic uranium

CERN Document Server

Xiong Bi Tao; Xue Wei Dong; Zhu Zheng He; Jiang Gang; Wang Hong Yan; Gao Tao

2002-01-01

According to the experimental data, there is an intermediate substance that formed in the initial stage of oxidation reaction when water vapor is absorbed onto the metallic uranium. The minimum energy of UOH sub 2 witch C sub 2 subupsilon configuration is obtained in the state of sup 5 A sub 1 by B3LYP method of the density function theory (DFT), which is consistent with that by statics of atoms and molecules reaction (AMRS) and group theory. The results from calculations indicate that the adsorption of water vapor on the metallic uranium is an exothermic reaction and that the adsorbed amount decreases with the elevated temperatures. The adsorptive heat at 1 atm is -205.4747 kJ centre dot mol sup - sup 1 , which indicates a typical chemical adsorption

Lithium adsorption on amorphous aluminum hydroxides and gibbsite

Directory of Open Access Journals (Sweden)

Konstantinos P. Prodromou

2016-01-01

Full Text Available Lithium (Li adsorption on both amorphous aluminum hydroxides and gibbsite was studied. For the amorphous Al(OH3 the adsorption was found to be pH dependent. Generally, 1.6 times more Li was adsorbed at initial pH value 8.0 compared with pH value 6.50. Gibbsite adsorbed 11.6 to 45.5 times less Li quantities compared with amorphous Al(OH3. Lithium adsorption was not depended on equilibrium times. It remained stable for all equilibrium times used. Lithium quantities extracted with 1N CH3COONH4 pH 7 , represent the physical adsorption, while the remaining Li that was adsorbed on Al(OH3, represents the chemical adsorption. During the desorption process 19% of Li extracted with NH4+, represents the physical adsorption, while the remaining 81% of Li, which was adsorbed represents the chemical adsorption. In gibbsite, 9.6% of Li represents the physical adsorption and 90.4% the chemical one. The experimental data conformed well to Freundlich isotherm equation.

On sulfur core level binding energies in thiol self-assembly and alternative adsorption sites: An experimental and theoretical study

International Nuclear Information System (INIS)

Jia, Juanjuan; Kara, Abdelkader; Pasquali, Luca; Bendounan, Azzedine; Sirotti, Fausto; Esaulov, Vladimir A.

2015-01-01

Characteristic core level binding energies (CLBEs) are regularly used to infer the modes of molecular adsorption: orientation, organization, and dissociation processes. Here, we focus on a largely debated situation regarding CLBEs in the case of chalcogen atom bearing molecules. For a thiol, this concerns the case when the CLBE of a thiolate sulfur at an adsorption site can be interpreted alternatively as due to atomic adsorption of a S atom, resulting from dissociation. Results of an investigation of the characteristics of thiol self-assembled monolayers (SAMs) obtained by vacuum evaporative adsorption are presented along with core level binding energy calculations. Thiol ended SAMs of 1,4-benzenedimethanethiol (BDMT) obtained by evaporation on Au display an unconventional CLBE structure at about 161.25 eV, which is close to a known CLBE of a S atom on Au. Adsorption and CLBE calculations for sulfur atoms and BDMT molecules are reported and allow delineating trends as a function of chemisorption on hollow, bridge, and atop sites and including the presence of adatoms. These calculations suggest that the 161.25 eV peak is due to an alternative adsorption site, which could be associated to an atop configuration. Therefore, this may be an alternative interpretation, different from the one involving the adsorption of atomic sulfur resulting from the dissociation process of the S–C bond. Calculated differences in S(2p) CLBEs for free BDMT molecules, SH group sulfur on top of the SAM, and disulfide are also reported to clarify possible errors in assignments

On sulfur core level binding energies in thiol self-assembly and alternative adsorption sites: An experimental and theoretical study

Energy Technology Data Exchange (ETDEWEB)

Jia, Juanjuan [Institut des Sciences Moléculaires d’Orsay, Université-Paris Sud, 91405 Orsay (France); CNRS, UMR 8214, Institut des Sciences Moléculaires d’Orsay, Orsay ISMO, Bâtiment 351, Université Paris Sud, 91405 Orsay (France); Kara, Abdelkader, E-mail: abdelkader.kara@ucf.edu, E-mail: vladimir.esaulov@u-psud.fr [Department of Physics, University of Central Florida, Orlando, Florida 32816 (United States); Pasquali, Luca [Dipartimento di Ingegneria “E. Ferrari,” Università di Modena e Reggio Emilia, Via Vignolese 905, 41125 Modena (Italy); IOM-CNR, s.s. 14, Km. 163.5 in AREA Science Park, 34149 Basovizza, Trieste (Italy); Department of Physics, University of Johannesburg, P.O. Box 524, Auckland Park 2006 (South Africa); Bendounan, Azzedine; Sirotti, Fausto [Synchrotron SOLEIL, L’Orme des Merisiers, Saint-Aubin, BP 48, F-91192 Gif-sur-Yvette Cedex (France); Esaulov, Vladimir A., E-mail: abdelkader.kara@ucf.edu, E-mail: vladimir.esaulov@u-psud.fr [Institut des Sciences Moléculaires d’Orsay, Université-Paris Sud, 91405 Orsay (France); CNRS, UMR 8214, Institut des Sciences Moléculaires d’Orsay, Orsay ISMO, Bâtiment 351, Université Paris Sud, 91405 Orsay (France); IOM-CNR, s.s. 14, Km. 163.5 in AREA Science Park, 34149 Basovizza, Trieste (Italy)

2015-09-14

Characteristic core level binding energies (CLBEs) are regularly used to infer the modes of molecular adsorption: orientation, organization, and dissociation processes. Here, we focus on a largely debated situation regarding CLBEs in the case of chalcogen atom bearing molecules. For a thiol, this concerns the case when the CLBE of a thiolate sulfur at an adsorption site can be interpreted alternatively as due to atomic adsorption of a S atom, resulting from dissociation. Results of an investigation of the characteristics of thiol self-assembled monolayers (SAMs) obtained by vacuum evaporative adsorption are presented along with core level binding energy calculations. Thiol ended SAMs of 1,4-benzenedimethanethiol (BDMT) obtained by evaporation on Au display an unconventional CLBE structure at about 161.25 eV, which is close to a known CLBE of a S atom on Au. Adsorption and CLBE calculations for sulfur atoms and BDMT molecules are reported and allow delineating trends as a function of chemisorption on hollow, bridge, and atop sites and including the presence of adatoms. These calculations suggest that the 161.25 eV peak is due to an alternative adsorption site, which could be associated to an atop configuration. Therefore, this may be an alternative interpretation, different from the one involving the adsorption of atomic sulfur resulting from the dissociation process of the S–C bond. Calculated differences in S(2p) CLBEs for free BDMT molecules, SH group sulfur on top of the SAM, and disulfide are also reported to clarify possible errors in assignments.

Experimental and computational investigation of adsorption performance of TC-5A and PSA-5A for manned spacecraft

Directory of Open Access Journals (Sweden)

Liu Meng

2015-12-01

Full Text Available Two kinds of molecular sieve materials, TC-5A and PSA-5A, were produced to satisfy with special requirement of manned space flight. Their CO2 adsorption performances were investigated and compared through two experiments, the thermo gravimetric analysis (TGA experiment and packed bed column experiment. Besides, some kinetic equations were compared according to the TGA experimental data, and their errors were analyzed. Finally, the classic linear driving force (LDF model is improved to the new Avrami’s model, and two models are analyzed based on the packed bed data. The TGA data shows that the CO2 loading has an approximately linear relationship with the CO2 concentration, and the best fit adsorption temperature range is from 283 to 303 K. The packed bed column results show that water vapor in air can affect the CO2 adsorption performance badly. The new Avrami’s model is proved more suitable to reflect the complex adsorption mechanism for two molecular sieves. The materials are proved having much better adsorption capacity than the other adsorbents with room temperature and low CO2 concentration (⩽1.0% in volume, and they can meet the aerospace requirements. This work will benefit the optimal design and simulation of the air revitalization (AR system for Chinese manned spacecraft.

A first-principles study of oxygen adsorption on Ir(111) surface

Energy Technology Data Exchange (ETDEWEB)

Gao, Hengjiao, E-mail: gaohengjiao@163.com; Xiong, Yuqing, E-mail: xiongyq@hotmail.com; Liu, Xiaoli, E-mail: shantianzi@126.com; Zhao, Dongcai, E-mail: zhaodongc@163.com; Feng, Yudong, E-mail: yudong_feng@sina.com; Wang, Lanxi, E-mail: wanglanxi@live.com; Wang, Jinxiao, E-mail: coldwind716@gmail.com

2016-12-15

Highlights: • Adsorption of oxygen on Ir(111) surface was studied by density functional theory. • The most stable adsorption site was determined by adsorption energy calculation. • Adsorption of oxygen at bridge and top site on Ir surface was the most stable ones. • Interaction of O 2p and Ir 5d orbits is relatively strong and formed hybridization. - Abstract: In order to understand deposition mechanism of iridium thin film by atomic layer deposition, the adsorption of oxygen on Ir(111) surface was studied by use of density functional theory and a periodical slab model. By calculating the adsorption energy and structure of oxygen at four adsorption sites (top, bridge, fcc-hollow and hcp-hollow) on Ir(111) surface, the most stable adsorption site was determined. On this basis, the banding mechanism of O and Ir atoms was studied by density of states of oxygen and iridium atoms. Oxygen adsorbed at hcp(parallel) site on Ir(111) surface was the most stable one according to the adsorption energy calculation results. Orbital charge analysis indicate that charge transferred from 5p and 5d orbit to 2p orbit of adsorbed O atoms, and 6s orbit of iridium atoms. Meanwhile, density of state study indicated that adsorption of oxygen on Ir(111) surface is mainly due to the interaction between 2p orbit of O atoms and 5d orbit of iridium atoms.

Adsorption of oxazole and isoxazole on BNNT surface: A DFT study

Energy Technology Data Exchange (ETDEWEB)

Kaur, Jasleen, E-mail: jasleen.chem@gmail.com; Singla, Preeti, E-mail: preetisingla21@gmail.com; Goel, Neetu, E-mail: neetugoel@pu.ac.in

2015-02-15

Highlights: • The adsorption of oxazole and isoxazole over (6,0) and (5,5) BNNTs is studied. • The adsorption energies and structural changes are inductive of covalent adsorption. • The solvent plays an important role in improving the adsorption properties. • The adsorption witnesses substantial changes in electronic properties of the BNNT. • The functionalization of the BNNTs open up their applicability as drug carrier. - Abstract: The adsorption behavior of oxazole and isoxazole heterocycles over the (6,0) zigzag and (5,5) armchair boron nitride nanotube (BNNT) has been studied within the formalism of density functional theory (DFT). The adsorption energies, the frontier molecular orbital (FMO) analysis and the structural changes at the adsorption site are indicative of covalent adsorption on the zigzag BNNT surface, while the adsorption is physical in nature on the armchair BNNT surface. The role of solvent in improving the adsorption properties over the BNNT surface is elucidated by reoptimizing the structures in aqueous phase. The solvation energy is indicative of remarkable increase in the solubility of BNNTs after adsorption of heterocyclic rings. The Density of states (DOS) Plots, natural bond orbital (NBO) analysis and the quantum molecular descriptors (QMD) are witness to the substantial changes in the electronic properties of the BNNT systems following the attachment of these heterocycles with the tube surface. The study envisages the functionalization of the BNNT as well as its applicability as carrier of the drugs containing heterocyclic rings oxazole and isoxazole with marked sensitivity to the type of adsorbate and the adsorbent.

Functionalized mesoporous silica materials for molsidomine adsorption: Thermodynamic study

International Nuclear Information System (INIS)

Alyoshina, Nonna A.; Parfenyuk, Elena V.

2013-01-01

A series of unmodified and organically modified mesoporous silica materials was prepared. The unmodified mesoporous silica was synthesized via sol–gel synthesis in the presence of D-glucose as pore-forming agent. The functionalized by phenyl, aminopropyl and mercaptopropyl groups silica materials were prepared via grafting. The fabricated adsorbent materials were characterized by Fourier transform infrared spectroscopy (FTIR) analysis, N 2 adsorption/desorption and elemental analysis methods. Then their adsorption properties for mesoionic dug molsidomine were investigated at 290–313 K and physiological pH value. Thermodynamic parameters of molsidomine adsorption on the synthesized materials have been calculated. The obtained results showed that the adsorption process of molsidomine on the phenyl modified silica is the most quantitatively and energetically favorable. The unmodified and mercaptopropyl modified silica materials exhibit significantly higher adsorption capacities and energies for molsidomine than the aminopropyl modified sample. The effects are discussed from the viewpoint of nature of specific interactions responsible for the adsorption. - Graphical abstract: Comparative analysis of the thermodynamic characteristics of molsidomine adsorption showed that the adsorption process on mesoporous silica materials is controlled by chemical nature of surface functional groups. Molsidomine adsorption on the phenyl modified silica is the most quantitatively and energetically favorable. Taking into account ambiguous nature of mesoionic compounds, it was found that molsidomine is rather aromatic than dipolar. Display Omitted - Highlights: • Unmodified and organically modified mesoporous silica materials were prepared. • Molsidomine adsorption on the silica materials was studied. • Phenyl modified silica shows the highest adsorption capacity and favorable energy. • Molsidomine exhibits the lowest affinity to aminopropyl modified silica

Adsorption on smooth electrodes: A radiotracer study

International Nuclear Information System (INIS)

Rice-Jackson, L.M.

1990-01-01

Adsorption on solids is a complicated process and in most cases, occurs as the early stage of other more complicated processes, i.e. chemical reactions, electrooxidation, electroreduction. The research reported here combines the electroanalytical method, cyclic voltammetry, and the use of radio-labeled isotopes, soft beta emitters, to study adsorption processes at smooth electrodes. The in-situ radiotracer method is highly anion (molecule) specific and provides information on the structure and composition of the electric double layer. The emphasis of this research was on studying adsorption processes at smooth electrodes of copper, gold, and platinum. The application of the radiotracer method to these smooth surfaces have led to direct in-situ measurements from which surface coverage was determined; anions and molecules were identified; and weak interactions of adsorbates with the surface of the electrodes were readily monitored. 179 refs

Batch kinetics, isotherm and thermodynamic studies of adsorption of strontium from aqueous solutions onto low cost rice-straw based carbons.

Directory of Open Access Journals (Sweden)

S. M. Yakout

2010-09-01

Full Text Available Present study explored the feasibility of using waste rice-straw based carbons as adsorbent for the removal of strontium under different experimental conditions. The batch sorption is studied with respect to solute concentration (2.8 - 110 mg/L, contact time, adsorbent dose (2.5 - 20 g/L and solution temperature (25 - 55oC. The Langmuir and Dubinin-Radushkevich adsorption models were applied to experimental equilibrium data and isotherm constants were calculated using linear regression analysis. A comparison of kinetic models applied to the adsorption of strontium on rice-straw carbon was evaluated for the pseudo-second-order, Elovich, intraparticle diffusion and Bangham’s kinetics models. The experimental data fitted very well the pseudosecond-order kinetic model and also followed by intra-particle diffusion model, whereas diffusion is not only the rate-controlling step. The results show that the sorption capacity increases with an increase in solution temperature from 25 to 55 oC. The thermodynamics parameters were evaluated. The positive value of ΔH (40.93 kJ indicated that the adsorption of strontium onto RS1 carbon was endothermic, which result was supported by the increasing adsorption of strontium with temperature. The positive value of ΔS (121.8 kJ/mol reflects good affinity of strontium ions towards the rice-straw based carbons. The results have establishedgood potentiality for the carbons particles to be used as a sorbent for the removal of strontium from wastewater.

Theoretical insight of adsorption cooling

KAUST Repository

Chakraborty, Anutosh

2011-06-03

This letter proposes and presents a thermodynamic formulation to calculate the energetic performances of an adsorption cooler as a function of pore widths and volumes of solid adsorbents. The simulated results in terms of the coefficient of performance are validated with experimental data. It is found from the present analysis that the performance of an adsorption cooling device is influenced mainly by the physical characteristics of solid adsorbents, and the characteristics energy between the adsorbent-adsorbate systems. The present study confirms that there exists a special type of silicagel having optimal physical characteristics that allows us to obtain the best performance.

Theoretical insight of adsorption cooling

KAUST Repository

Chakraborty, Anutosh; Leong, Kai Choong; Thu, Kyaw; Saha, Bidyut Baran; Ng, Kim Choon

2011-01-01

This letter proposes and presents a thermodynamic formulation to calculate the energetic performances of an adsorption cooler as a function of pore widths and volumes of solid adsorbents. The simulated results in terms of the coefficient of performance are validated with experimental data. It is found from the present analysis that the performance of an adsorption cooling device is influenced mainly by the physical characteristics of solid adsorbents, and the characteristics energy between the adsorbent-adsorbate systems. The present study confirms that there exists a special type of silicagel having optimal physical characteristics that allows us to obtain the best performance.

Potential Theory of Multicomponent Adsorption

DEFF Research Database (Denmark)

Shapiro, Alexander; Stenby, Erling Halfdan

1998-01-01

We developed a theory of multicomponent adsorption on the basis of the potential concept originally suggested by Polanyi. The mixture is considered as a heterogeneous substance segregated in the external field emitted by the adsorbent. The same standard equation of state, with no additional fitting...... and high degree of predictability of the theory developed....... the potential theory and the spreading pressure concept is established, and problems of the theory consistency are studied. Numerical algorithms are suggested for evaluation of the segregated state of the mixture in the potential field of adsorption forces. Comparison with experimental data shows good agreement...

Transient behaviour of an adsorption refrigerator. Experimental study of the alcohol/activated carbon system; Comportement transitoire d`une machine frigorifique a absorption. Etude experimentale du systeme alcool / charbon actif

Energy Technology Data Exchange (ETDEWEB)

Luo, L. [Centre National de la Recherche Scientifique (CNRS), 54 - Nancy (France). Lab. des sciences du genie chimique; Feidt, M. [Nancy-1 Univ., 54 - Vandoeuvre-les-Nancy (France)

1997-03-01

The objective of this article is to present an experimental study of an adsorption refrigerator, accounting for the transient phenomena in each component of the machine, in particular in the adsorber. The couples adsorbate/adsorbent investigated (activated carbon/methanol or ethanol) have been chosen on the basis of an earlier comparative study. We have performed a full series of experiments to investigate the transient evolution of temperatures, pressures and the cycled mass, in a discontinuous cycle, and along the components of the refrigerating machine. The influence of various parameters is studies by varying one at a time: adsorbate/ adsorbent couple, alcohol load in adsorber, alcohol flowrate, heating power, initial desorption temperature. All these experimental observation are discussed and compared to transient models developed in a separate article. (authors) 12 refs.

Adsorption and desorption dynamics of citric acid anions in soil

KAUST Repository

Oburger, E.

2011-07-26

The functional role of organic acid anions in soil has been intensively investigated, with special focus on (i) microbial respiration and soil carbon dynamics, (ii) nutrient solubilization or (iii) metal detoxification and reduction of plant metal uptake. Little is known about the interaction dynamics of organic acid anions with the soil matrix and the potential impact of adsorption and desorption processes on the functional significance of these effects. The aim of this study was to characterize experimentally the adsorption and desorption dynamics of organic acid anions in five agricultural soils differing in iron and aluminium oxide contents and using citrate as a model carboxylate. Results showed that both adsorption and desorption processes were fast in all soils, reaching a steady state within approximately 1 hour. However, for a given total soil citrate concentration (ct) the steady state was critically dependent on the starting conditions of the experiment, whether most of the citrate was initially present in solution (cl) or held on the solid phase (cs). Specifically, desorption-led processes resulted in significantly smaller steady-state solution concentrations than adsorption-led processes, indicating that hysteresis occurred. As it is not possible to distinguish between different adsorption and desorption pools in soil experimentally, a new dynamic hysteresis model that relies only on measured soil solution concentrations was developed. The model satisfactorily explained experimental data and was able to predict dynamic adsorption and desorption behaviour. To demonstrate its use, we applied the model to two relevant situations involving exudation and microbial degradation. The study highlighted the complex nature of citrate adsorption and desorption dynamics in soil. We conclude that existing models need to incorporate both temporal and hysteresis components to describe realistically the role and fate of organic acids in soil processes. © 2011 The

Modeling of boldine alkaloid adsorption onto pure and propyl-sulfonic acid-modified mesoporous silicas. A comparative study

Energy Technology Data Exchange (ETDEWEB)

Geszke-Moritz, Małgorzata, E-mail: Malgorzata.Geszke-Moritz@amu.edu.pl [NanoBioMedical Centre, Adam Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Moritz, Michał, E-mail: michal.moritz@put.poznan.pl [Poznan University of Technology, Faculty of Chemical Technology, Institute of Chemistry and Technical Electrochemistry, Berdychowo 4, 60-965 Poznań (Poland)

2016-12-01

The present study deals with the adsorption of boldine onto pure and propyl-sulfonic acid-functionalized SBA-15, SBA-16 and mesocellular foam (MCF) materials. Siliceous adsorbents were characterized by nitrogen sorption analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy and thermogravimetric analysis. The equilibrium adsorption data were analyzed using the Langmuir, Freundlich, Redlich-Peterson, and Temkin isotherms. Moreover, the Dubinin-Radushkevich and Dubinin-Astakhov isotherm models based on the Polanyi adsorption potential were employed. The latter was calculated using two alternative formulas including solubility-normalized (S-model) and empirical C-model. In order to find the best-fit isotherm, both linear regression and nonlinear fitting analysis were carried out. The Dubinin-Astakhov (S-model) isotherm revealed the best fit to the experimental points for adsorption of boldine onto pure mesoporous materials using both linear and nonlinear fitting analysis. Meanwhile, the process of boldine sorption onto modified silicas was described the best by the Langmuir and Temkin isotherms using linear regression and nonlinear fitting analysis, respectively. The values of adsorption energy (below 8 kJ/mol) indicate the physical nature of boldine adsorption onto unmodified silicas whereas the ionic interactions seem to be the main force of alkaloid adsorption onto functionalized sorbents (energy of adsorption above 8 kJ/mol). - Graphical abstract: Modeling of boldine adsorption onto unmodified and propyl-sulfonic acid-modified mesoporous adsorbents. - Highlights: • The process of boldine adsorption onto SBA-15, SBA-16 and MCF silicas was examined. • Siliceous adsorbents were functionalized with propyl-sulfonic acid groups. • The equilibrium adsorption data were analyzed using several isotherm models. • Both linear regression and nonlinear fitting analysis were carried out. �

Functionalized mesoporous silica materials for molsidomine adsorption: Thermodynamic study

Energy Technology Data Exchange (ETDEWEB)

Alyoshina, Nonna A.; Parfenyuk, Elena V., E-mail: evp@iscras.ru

2013-09-15

A series of unmodified and organically modified mesoporous silica materials was prepared. The unmodified mesoporous silica was synthesized via sol–gel synthesis in the presence of D-glucose as pore-forming agent. The functionalized by phenyl, aminopropyl and mercaptopropyl groups silica materials were prepared via grafting. The fabricated adsorbent materials were characterized by Fourier transform infrared spectroscopy (FTIR) analysis, N{sub 2} adsorption/desorption and elemental analysis methods. Then their adsorption properties for mesoionic dug molsidomine were investigated at 290–313 K and physiological pH value. Thermodynamic parameters of molsidomine adsorption on the synthesized materials have been calculated. The obtained results showed that the adsorption process of molsidomine on the phenyl modified silica is the most quantitatively and energetically favorable. The unmodified and mercaptopropyl modified silica materials exhibit significantly higher adsorption capacities and energies for molsidomine than the aminopropyl modified sample. The effects are discussed from the viewpoint of nature of specific interactions responsible for the adsorption. - Graphical abstract: Comparative analysis of the thermodynamic characteristics of molsidomine adsorption showed that the adsorption process on mesoporous silica materials is controlled by chemical nature of surface functional groups. Molsidomine adsorption on the phenyl modified silica is the most quantitatively and energetically favorable. Taking into account ambiguous nature of mesoionic compounds, it was found that molsidomine is rather aromatic than dipolar. Display Omitted - Highlights: • Unmodified and organically modified mesoporous silica materials were prepared. • Molsidomine adsorption on the silica materials was studied. • Phenyl modified silica shows the highest adsorption capacity and favorable energy. • Molsidomine exhibits the lowest affinity to aminopropyl modified silica.

Chemical treatment effect on physi-sorption properties of nano-fibres: an experimental and theoretical study

Energy Technology Data Exchange (ETDEWEB)

Kayiran, S.B.; Darkrim, F.L.; Gicquel, A. [Paris-Nord Univ., Laboratoire d' Ingenierie des Materiaux et des Hautes Pressions UPR 1311, 93 - Villetaneuse (France); Bernier, P. [Groupe de Dynamique des Phases Condensees, UMR5581 UMII, 34 - Montpellier (France); Gadelle, P. [Universite Joseph Fourier ENSEEG, 38 - St Martin d' Heres (France); Levesque, D. [Paris-11 Univ., Laboratoire de Physique theorique UMR 8627, 91 - Orsay (France)

2003-09-01

In this work, we have realized experimental studies of gas adsorption in purified and raw graphitic nano-fibres (GNFs) obtained by CVD method, at a pressure of 20 MPa and a temperature of 293 K. The structural characterizations of these adsorbents have been evaluated by X-ray diffraction, transmission electronic microscopy, specific surface area measurements at 77 K, chemical analysis and Raman spectroscopy. We have also realized Monte Carlo simulations of hydrogen adsorption in GNF model. The results of the simulations, realized in the Grand Canonical ensemble, are compared to experimental data. (authors)

Study on a waste heat-driven adsorption cooling cum desalination cycle

KAUST Repository

Ng, Kim Choon

2012-05-01

This article presents the performance analysis of a waste heat-driven adsorption cycle. With the implementation of adsorption-desorption phenomena, the cycle simultaneously produces cooling energy and high-grade potable water. A mathematical model is developed using isotherm characteristics of the adsorbent/adsorbate pair (silica gel and water), energy and mass balances for the each component of the cycle. The cycle is analyzed using key performance parameters namely (i) specific cooling power (SCP), (ii) specific daily water production (SDWP), (iii) the coefficient of performance (COP) and (iv) the overall conversion ratio (OCR). The numerical results of the adsorption cycle are validated using experimental data. The parametric analysis using different hot and chilled water temperatures are reported. At 85°C hot water inlet temperature, the cycle generates 3.6 m 3 of potable water and 23 Rton of cooling at the produced chilled water temperature of 10°C. © 2012 Elsevier Ltd and IIR. All rights reserved.

Non-equilibrium dynamics of single polymer adsorption to solid surfaces

International Nuclear Information System (INIS)

Panja, Debabrata; Barkema, Gerard T; Kolomeisky, Anatoly B

2009-01-01

The adsorption of polymers to surfaces is crucial for understanding many fundamental processes in nature. Recent experimental studies indicate that the adsorption dynamics is dominated by non-equilibrium effects. We investigate the adsorption of a single polymer of length N to a planar solid surface in the absence of hydrodynamic interactions. We find that for weak adsorption energies the adsorption timescales ∼N (1+2ν)/(1+ν) , where ν is the Flory exponent for the polymer. We argue that in this regime the single chain adsorption is closely related to a field-driven polymer translocation through narrow pores. Surprisingly, for high adsorption energies the adsorption time becomes longer, as it scales as ∼N 1+ν , which is explained by strong stretching of the unadsorbed part of the polymer close to the adsorbing surface. These two dynamic regimes are separated by an energy scale that is characterized by non-equilibrium contributions during the adsorption process. (fast track communication)

Equilibrium and kinetics studies of metal ion adsorption on dyed ...

African Journals Online (AJOL)

Batch equilibration studies were conducted to determine the nature of adsorption of Zn (II) and Cu (II) onto dyed coconut pollens. The nature of adsorption of metal ions was explained using the Langmuir equation. The calculated values of equilibrium parameter indicated favourable adsorption by the adsorbents. Also the ...

Adsorption properties of fission gases Xe and Kr on pristine and doped graphene: A first principle DFT study

Energy Technology Data Exchange (ETDEWEB)

Vazhappilly, Tijo, E-mail: tijoj@barc.gov.in [Theoretical Chemistry Section, Chemistry Group, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Ghanty, Tapan K., E-mail: tapang@barc.gov.in [Theoretical Chemistry Section, Chemistry Group, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400094 (India); Jagatap, B.N. [Theoretical Chemistry Section, Chemistry Group, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2017-07-15

Graphene has excellent adsorption properties due to large surface area and has been used in applications related to gas sorption and separation. The separation of radioactive noble gases using graphene is an interesting area of research relevant to nuclear waste management. Radioactive noble gases Xe and Kr are present in the off-gas streams from nuclear fission reactors and spent nuclear fuel reprocessing plants. The entrapment of these volatile fission gases is important in the context of nuclear safety. The separation of Xe from Kr is extremely difficult, and energy intensive cryogenic distillation is generally employed. Physisorption based separation techniques using porous materials is a cost effective alternative to expensive cryogenic distillation. Thus, adsorption of noble gases on graphene is relevant for fundamental understanding of physisorption process. The properties of graphene can be tuned by doping and incorporation of defects. In this regard, we study the binding affinity of Xe and Kr in pristine and doped graphene sheets. We employ first principle calculations using density functional theory, corrected for dispersion interactions. The structural parameters obtained from the current study show excellent agreement with the available theoretical and experimental observations on similar systems. Noble gas adsorption energies on pristine graphene match very well with the available literature. Our results show that the binding energy of fission gases Xe and Kr on graphene can be considerably improved through doping the lattice with a heteroatom. - Graphical abstract: The adsorption of radioactive fission gases Xe and Kr on pristine/doped graphene is an interesting topic in the context of nuclear waste management. Previous experimental and computational studies about Xe/Kr adsorption on graphene were limited to only on pristine graphene. The doping by hetero atom changes the electronic properties of graphene and creates active sites in the lattice. Based

Adsorption of Zinc(II) on diatomite and manganese-oxide-modified diatomite: a kinetic and equilibrium study.

Science.gov (United States)

Caliskan, Necla; Kul, Ali Riza; Alkan, Salih; Sogut, Eda Gokirmak; Alacabey, Ihsan

2011-10-15

The removal of Zn(II) ions from aqueous solution was studied using natural and MnO(2) modified diatomite samples at different temperatures. The linear Langmuir, Freundlich and Dubinin-Radushkevich (D-R) adsorption equations were applied to describe the equilibrium isotherms. From the D-R model, the mean adsorption energy was calculated as >8 kJ mol(-1), indicating that the adsorption of Zn(II) onto diatomite and Mn-diatomite was physically carried out. In addition, the pseudo-first-order, pseudo-second-order and intraparticle diffusion models were used to determine the kinetic data. The experimental data were well fitted by the pseudo-second-order kinetic model. Thermodynamic parameters such as the enthalpy (ΔH(0)), Gibbs' free energy (ΔG(0)) and entropy (ΔS(0)) were calculated for natural and MnO(2) modified diatomite. These values showed that the adsorption of Zn(II) ions onto diatomite samples was controlled by a physical mechanism and occurred spontaneously. Copyright © 2011 Elsevier B.V. All rights reserved.

Probing adsorption sites of carbon dioxide in metal organic framework of [Zn(bdc)(dpds)]n: A molecular simulation study

Science.gov (United States)

Lu, Shih-I.; Liao, Jian-Min; Huang, Xiao-Zhuang; Lin, Chia-Hsun; Ke, Szu-Yu; Wang, Chih-Chieh

2017-11-01

We used force-field based grand-canonical Monte Carlo simulation method and density functional theory to study adsorption characteristics of carbon dioxide (CO2) molecules in a metal-organic framework (MOF) compound, [Zn(bdc)(dpds)]n. The studied MOF include a metal ion (Zn(II)), an anion organic linker (dianion of benzene dicarboxylicacid, bdc2-) and a neutral organic linker (4,4‧-dipyridyldisulfide, dpds). Results from calculated adsorption isotherms and enthalpies of adsorption agree with the experimental data. The interactions between the adsorbed CO2 and the organic linkers were examined in simulations. Calculated results show available absorption sites are surrounded by two dpds ligands in which an S-S bond as an N-N‧ spacer connect two pyridines. In contrast, the bdc2- ligand does not give a significant contribution to the substantial adsorption amount even though it contains the carboxylate group that provides available bonding site to CO2.

Using Adsorption Isotherm Studies to Determine Crosslinked Polymeric Adsorbent Performance in Heavy Metals Removal from Water

Directory of Open Access Journals (Sweden)

Nasrin Sheikh

2015-01-01

Full Text Available Polymeric adsorbents are useful tools for removing heavy metals from aqueous solutions. Adsorption models are efficient tools for accurate prediction and evaluation of the practical adsorption process in real situation. In this study, the two isotherms of Langmuir and Dubinin-Radushkevich models were employed to investigate the absorption performance of chitosan, PVA, and chitosan/PVA blend (with a weight ratio of 1:1 in the removal of Mn (II and Ni (II from aqueous solutions. The PVA adsorbent was crosslinked by both chemical and radiation methods while the others were crosslinked only chemically due to Chitosan’s lack of resistance to radiation. The results showed that the Langmuir model fitted the experimental data better than the Dubinin-Radushkevich one for both metals. The maximum adsorption capacity (qmax of the Langmuir model showed that the PVA/Chitosan adsorbent had the best adsorption compared to other adsorbents, with 52.63 mg/g for Ni and 30.30 mg/g for Mn (evidently more Ni was absorbed than Mn. Also, maximum adsorption by the chemically crosslinked PVA was 38.46 mg/g for Ni and 19.23 mg/g for Mn, which exhibits a higher level than adsorption by the radiation crosslinked PVA The results indicate that absorption capacity depends on the type of adsorbed metal, absorbent structure, and the crosslinking method employed.

Thermodynamic Study of Adsorption of Phenol, 4-Chlorophenol, and 4-Nitrophenol on Activated Carbon Obtained from Eucalyptus Seed

Directory of Open Access Journals (Sweden)

Nelson Giovanny Rincón-Silva

2015-01-01

Full Text Available Activated carbons from shell eucalyptus (Eucalyptus globulus were prepared by chemical activation through impregnation with solutions of two activators: sulfuric acid and sodium hydroxide, the surface areas for activated carbons with base were 780 and 670 m2 g−1 and the solids activated with acid were 150 and 80 m2 g−1. These were applying in adsorption of priority pollutants: phenol, 4-nitrophenol, and 4-chlorophenol from aqueous solution. Activated carbon with the highest adsorption capacity has values of 2.12, 2.57, and 3.89 on phenol, 4-nitrophenol, and 4-chlorophenol, respectively, and was activated with base. In general, all carbons adsorption capacity was given in the following order: 4-chlorophenol > 4-nitrophenol > phenol. Adsorption isotherms of phenols on activated carbons were fitted to the Langmuir, Freundlich, and Dubinin-Radusckevisch-Kanager models, finding great association between them and experimental data. A thermodynamic study was performed, the exothermic nature and spontaneous nature of the adsorption process were confirmed, and the favorability of adsorption on activated carbons with NaOH was confirmed by energy relations and concluded that the adsorption process of phenolic compounds from the activated carbon obtained is physical. The pH of solutions and pH at point of zero charge of the solid play an important role in the adsorption process.

WATER ADSORPTION AND DESORPTION ISOTHERMS ON MILK POWDER: II. WHOLE MILK

OpenAIRE

Edgar M. Soteras; Julio Gil; Paola Yacanto; Silvana Muratona; Clidia Abaca; María G. Sustersic

2014-01-01

The aim of this research was the determination of adsorption and desorption isotherms of cow whole milk powder. The experiments have been carried out at 15, 25 and 40 ºC, in ranges of moisture and water activity characteristic of normal conditions in which the processes of drying, packaging and storage are developed. By studying the influence of the temperature on the experimental plots, the isosteric adsorption heat was determined. Experimental data were correlated to the referential model ...

Competitive adsorption of arsenate and phosphate onto calcite; experimental results and modeling with CCM and CD-MUSIC

DEFF Research Database (Denmark)

Sø, Helle Ugilt; Postma, Dieke; Jakobsen, Rasmus

2012-01-01

The competitive adsorption of arsenate and phosphate onto calcite was studied in batch experiments using calcite-equilibrated solutions. The solutions had circum-neutral pH (7–8.3) and covered a wide span in the activity of Ca2+ and View the MathML source. The results show that the adsorption...... that adsorption of arsenate onto calcite is of minor importance in most groundwater aquifers, as phosphate is often present at concentration levels sufficient to significantly reduce arsenate adsorption. The CD-MUSIC model for calcite was used successfully to model adsorption of arsenate and phosphate separately...

Theoretical study of cisplatin adsorption on silica

Energy Technology Data Exchange (ETDEWEB)

Simonetti, S., E-mail: ssimonet@uns.edu.ar [Departamento de Fisica and IFISUR, Universidad Nacional del Sur-CONICET, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Departamentos de Ciencias Basicas e Ingenieria Mecanica, Universidad Tecnologica Nacional, 11 de Abril 461, 8000 Bahia Blanca (Argentina); Company, A. Diaz; Brizuela, G.; Juan, A. [Departamento de Fisica and IFISUR, Universidad Nacional del Sur-CONICET, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

2011-11-15

The adsorption of cisplatin and its complexes, cis-[PtCl(NH{sub 3}){sub 2}]{sup +} and cis-[Pt(NH{sub 3}){sub 2}]{sup 2+}, on a SiO{sub 2}(1 1 1) hydrated surface has been studied by the Atom Superposition and Electron Delocalization method. The adiabatic energy curves for the adsorption of the drug and its products on the delivery system were considered. The electronic structure and bonding analysis were also performed. The molecule-surface interactions are formed at expenses of the OH surface bonds. The more important interactions are the Cl-H bond for cis-[PtCl{sub 2}(NH{sub 3}){sub 2}] and cis-[PtCl(NH{sub 3}){sub 2}]{sup +} adsorptions, and the Pt-O interaction for cis-[Pt(NH{sub 3}){sub 2}]{sup 2+} adsorption. The Cl p orbitals and Pt s, p y d orbitals of the molecule and its complexes, and the s H orbital and, the s and p orbitals of the O atoms of the hydrated surface are the main contribution to the surface bonds.

Adsorption characteristics of siloxanes in landfill gas by the adsorption equilibrium test

International Nuclear Information System (INIS)

Nam, Sangchul; Namkoong, Wan; Kang, Jeong-Hee; Park, Jin-Kyu; Lee, Namhoon

2013-01-01

Highlights: • Equilibrium test was attempted to evaluate adsorption characteristics of siloxane. • L2 had higher removal efficiency in carbon compared to noncarbon adsorbents. • Total adsorption capacity of siloxane was 300 mg/g by coal activated carbon. • Adsorption characteristics rely on size of siloxane molecule and adsorbent pore. • Conversion of siloxane was caused by adsorption of noncarbon adsorbents. - Abstract: Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane

Adsorption characteristics of siloxanes in landfill gas by the adsorption equilibrium test

Energy Technology Data Exchange (ETDEWEB)

Nam, Sangchul; Namkoong, Wan [Department of Environmental Engineering, Konkuk University, Hwayang-Dong, Gwangjin-Gu, Seoul 143-701 (Korea, Republic of); Kang, Jeong-Hee; Park, Jin-Kyu [Department of Environmental Engineering, Anyang University, Anyang 5-Dong, Manan-Gu, Anyang-Si, Gyeonggi-Do 430-714 (Korea, Republic of); Lee, Namhoon, E-mail: nhlee@anyang.ac.kr [Department of Environmental Engineering, Anyang University, Anyang 5-Dong, Manan-Gu, Anyang-Si, Gyeonggi-Do 430-714 (Korea, Republic of)

2013-10-15

Highlights: • Equilibrium test was attempted to evaluate adsorption characteristics of siloxane. • L2 had higher removal efficiency in carbon compared to noncarbon adsorbents. • Total adsorption capacity of siloxane was 300 mg/g by coal activated carbon. • Adsorption characteristics rely on size of siloxane molecule and adsorbent pore. • Conversion of siloxane was caused by adsorption of noncarbon adsorbents. - Abstract: Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane.

Adsorption of Zinc(II) on diatomite and manganese-oxide-modified diatomite: A kinetic and equilibrium study

Energy Technology Data Exchange (ETDEWEB)

Caliskan, Necla, E-mail: ncaliskan7@hotmail.com [Department of Physical Chemistry, Faculty of Science, Yuezuencue Yil University, Van 65080 (Turkey); Kul, Ali Riza; Alkan, Salih; Sogut, Eda Gokirmak; Alacabey, Ihsan [Department of Physical Chemistry, Faculty of Science, Yuezuencue Yil University, Van 65080 (Turkey)

2011-10-15

Highlights: {center_dot}The removal of Zn(II) ions from aqueous solution was studied using natural and MnO{sub 2} modified diatomite samples at different temperatures. {center_dot} The sorption of Zn(II) on the natural and modified diatomite was an endothermic processes, controlled by physical mechanisms and spontaneously. {center_dot} Adsorption of zinc metal ion on diatomite samples is more or less a two step process. {center_dot} Adsorption of Zn(II) on natural and modified diatomite could be explained by the mechanism of pseudo-second-order. - Abstract: The removal of Zn(II) ions from aqueous solution was studied using natural and MnO{sub 2} modified diatomite samples at different temperatures. The linear Langmuir, Freundlich and Dubinin-Radushkevich (D-R) adsorption equations were applied to describe the equilibrium isotherms. From the D-R model, the mean adsorption energy was calculated as >8 kJ mol{sup -1}, indicating that the adsorption of Zn(II) onto diatomite and Mn-diatomite was physically carried out. In addition, the pseudo-first-order, pseudo-second-order and intraparticle diffusion models were used to determine the kinetic data. The experimental data were well fitted by the pseudo-second-order kinetic model. Thermodynamic parameters such as the enthalpy ({Delta}H{sup 0}), Gibbs' free energy ({Delta}G{sup 0}) and entropy ({Delta}S{sup 0}) were calculated for natural and MnO{sub 2} modified diatomite. These values showed that the adsorption of Zn(II) ions onto diatomite samples was controlled by a physical mechanism and occurred spontaneously.

Surface Complexation Modeling of Fluoride Adsorption by Soil and the Role of Dissolved Aluminum on Adsorption

Science.gov (United States)

Padhi, S.; Tokunaga, T.

2017-12-01

Adsorption of fluoride (F) on soil can control the mobility of F and subsequent contamination of groundwater. Hence, accurate evaluation of adsorption equilibrium is a prerequisite for understanding transport and fate of F in the subsurface. While there have been studies for the adsorption behavior of F with respect to single mineral constituents based on surface complexation models (SCM), F adsorption to natural soil in the presence of complexing agents needs much investigation. We evaluated the adsorption processes of F on a natural granitic soil from Tsukuba, Japan, as a function of initial F concentration, ionic strength, and initial pH. A SCM was developed to model F adsorption behavior. Four possible surface complexation reactions were postulated with and without including dissolved aluminum (Al) and Al-F complex sorption. Decrease in F adsorption with the increase in initial pH was observed in between the initial pH range of 4 to 9, and a decrease in the rate of the reduction of adsorbed F with respect to the increase in the initial pH was observed in the initial pH range of 5 to 7. Ionic strength variation in the range of 0 to 100mM had insignificant effect on F removal. Changes in solution pH were observed by comparing the solution before and after F adsorption experiments. At acidic pH, the solution pH increased, whereas at alkaline pH, the solution pH decreased after equilibrium. The SCM including dissolved Al and the adsorption of Al-F complex can simulate the experimental results quite successfully. Also, including dissolved Al and the adsorption of Al-F complex to the model explained the change in solution pH after F adsorption.

Adsorption studies of methylene blue and phenol onto vetiver roots activated carbon prepared by chemical activation.

Science.gov (United States)

Altenor, Sandro; Carene, Betty; Emmanuel, Evens; Lambert, Jacques; Ehrhardt, Jean-Jacques; Gaspard, Sarra

2009-06-15

Vetiver roots have been utilized for the preparation of activated carbon (AC) by chemical activation with different impregnation ratios of phosphoric acid, X(P) (gH(3)PO(4)/g precursor): 0.5:1; 1:1 and 1.5:1. Textural characterization, determined by nitrogen adsorption at 77K shows that mixed microporous and mesoporous structures activated carbons (ACs) with high surface area (>1000 m(2)/g) and high pore volume (up to 1.19 cm(3)/g) can be obtained. The surface chemical properties of these ACs were investigated by X-ray photoelectron spectroscopy (XPS) and Boehm titration. Their textural and chemical characteristics were compared to those of an AC sample obtained by steam activation of vetiver roots. Classical molecules used for characterizing liquid phase adsorption, phenol and methylene blue (MB), were used. Adsorption kinetics of MB and phenol have been studied using commonly used kinetic models, i.e., the pseudo-first-order model, the pseudo-second-order model, the intraparticle diffusion model and as well the fractal, BWS (Brouers, Weron and Sotolongo) kinetic equation. The correlation coefficients (R(2)) and the normalized standard deviation Deltaq (%) were determined showing globally, that the recently derived fractal kinetic equation could best describe the adsorption kinetics for the adsorbates tested here, indicating a complex adsorption mechanism. The experimental adsorption isotherms of these molecules on the activated carbon were as well analysed using four isotherms: the classical Freundlich, Langmuir, Redlich-Peterson equations, but as well the newly published deformed Weibull Brouers-Sotolongo isotherm. The results obtained from the application of the equations show that the best fits were achieved with the Brouers-Sotolongo equation and with the Redlich-Peterson equation. Influence of surface functional groups towards MB adsorption is as well studied using various ACs prepared from vetiver roots and sugar cane bagasse. Opposite effects governing MB

Theoretical and experimental studies on the corrosion inhibition potentials of some purines for aluminum in 0.1 M HCl.

Science.gov (United States)

Eddy, Nnabuk O; Momoh-Yahaya, H; Oguzie, Emeka E

2015-03-01

Experimental aspect of the corrosion inhibition potential of adenine (AD), guanine (GU) and, hypoxanthine (HYP) was carried out using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) methods while the theoretical aspect of the work was carried out by calculations of semi-empirical parameters (for AM1, MNDO, CNDO, PM3 and RM1 Hamiltonians), Fukui functions and inhibitor-metal interaction energies. Results obtained from the experimental studies were in good agreement and indicated that adenine (AD), guanine (GU) and hypoxanthine (HYP) are good adsorption inhibitors for the corrosion of aluminum in solutions of HCl. Data obtained from electrochemical experiment revealed that the studied purines functioned by adsorption on the aluminum/HCl interface and inhibited the cathodic half reaction to a greater extent and anodic half reaction to a lesser extent. The adsorption of the purines on the metal surface was found to be exothermic and spontaneous. Deviation of the adsorption characteristics of the studied purines from the Langmuir adsorption model was compensated by the fitness of Flory Huggins and El Awardy et al. adsorption models. Quantum chemical studies revealed that the experimental inhibition efficiencies of the studied purines are functions of some quantum chemical parameters including total energy of the molecules (TE), energy gap (E L-H), electronic energy of the molecule (EE), dipole moment and core-core repulsion energy (CCR). Fukui functions analysis through DFT and MP2 theories indicated slight complications and unphysical results. However, results obtained from calculated Huckel charges, molecular orbital and interaction energies, the adsorption of the inhibitors proceeded through the imine nitrogen (N5) in GU, emanine nitrogen (N7) in AD and the pyridine nitrogen (N5) in HPY.

Nitrotyrosine adsorption on carbon nanotube: a density functional theory study

Science.gov (United States)

Majidi, R.; Karami, A. R.

2014-05-01

We have studied the effect of nitrotyrosine on electronic properties of different single-wall carbon nanotubes by density functional theory. Optimal adsorption configurations of nitrotyrosine adsorbed on carbon nanotube have been determined by calculation of adsorption energy. Adsorption energies indicate that nitrotyrosine is chemisorbed on carbon nanotubes. It is found that the nitrotyrosine adsorption modifies the electronic properties of the semiconducting carbon nanotubes significantly and these nanotubes become n-type semiconductors, while the effect of nitrotyrosine on metallic carbon nanotubes is not considerable and these nanotubes remain metallic. Results clarify sensitivity of carbon nanotubes to nitrotyrosine adsorption and suggest the possibility of using carbon nanotubes as biosensor for nitrotyrosine detection.

Theoretical study of adsorption of lithium atom on carbon nanotube

OpenAIRE

Senami, Masato; Ikeda, Yuji; Fukushima, Akinori; Tachibana, Akitomo

2011-01-01

We investigate the adsorption of lithium atoms on the surface of the (12, 0) single wall carbon nanotube (SWCNT) by using ab initio quantum chemical calculations. The adsorption of one lithium atom on the inside of this SWCNT is favored compared to the outside. We check this feature by charge transfer and regional chemical potential density. The adsorption of multiple lithium atoms on the interior of the SWCNT is studied in terms of adsorption energy and charge transfer. We show that repulsiv...

Heavy metals adsorption by novel EDTA-modified chitosan-silica hybrid materials.

Science.gov (United States)

Repo, Eveliina; Warchoł, Jolanta K; Bhatnagar, Amit; Sillanpää, Mika

2011-06-01

Novel adsorbents were synthesized by functionalizing chitosan-silica hybrid materials with (ethylenediaminetetraacetic acid) EDTA ligands. The synthesized adsorbents were found to combine the advantages of both silica gel (high surface area, porosity, rigid structure) and chitosan (surface functionality). The Adsorption potential of hybrid materials was investigated using Co(II), Ni(II), Cd(II), and Pb(II) as target metals by varying experimental conditions such as pH, contact time, and initial metal concentration. The kinetic results revealed that the pore diffusion process played a key role in adsorption kinetics, which might be attributed to the porous structure of synthesized adsorbents. The obtained maximum adsorption capacities of the hybrid materials for the metal ions ranged from 0.25 to 0.63 mmol/g under the studied experimental conditions. The adsorbent with the highest chitosan content showed the best adsorption efficiency. Bi-Langmuir and Sips isotherm model fitting to experimental data suggested the surface heterogeneity of the prepared adsorbents. In multimetal solutions, the hybrid adsorbents showed the highest affinity toward Pb(II). Copyright © 2011 Elsevier Inc. All rights reserved.

Parametric and kinetic study of adsorptive removal of dyes from aqueous solutions using an agriculture waste

Science.gov (United States)

Bencheikh, imane; el hajjaji, souad; abourouh, imane; Kitane, Said; Dahchour, Abdelmalek; El M'Rabet, Mohammadine

2017-04-01

Wastewater treatment is the subject of several studies through decades. Interest is continuously oriented to provide cheaper and efficient methods of treatment. Several methods of treatment exit including coagulation flocculation, filtration, precipitation, ozonation, ion exchange, reverse osmosis, advanced oxidation process. The use of these methods proved limited because of their high investment and operational cost. Adsorption can be an efficient low-cost process to remove pollutants from wastewater. This method of treatment calls for an solid adsorbent which constitutes the purification tool. Agricultural wastes have been widely exploited in this case .As we know the agricultural wastes are an important source of water pollution once discharged into the aquatic environment (river, sea ...). The valorization of such wastes and their use allows the prevention of this problem with an economic and environment benefits. In this context our study aimed testing the wastewater treatment capacity by adsorption onto holocellulose resulting from the valorization of an agriculture waste. In this study, methylene blue (MB) and methyl orange (MO) are selected as models pollutants for evaluating the holocellulose adsorbent capacity. The kinetics of adsorption is performed using UV-visible spectroscopy. In order to study the effect of the main parameters for the adsorption process and their mutual interaction, a full factorial design (type nk) has been used.23 full factorial design analysis was performed to screen the parameters affecting dye removal efficiency. Using the experimental results, a linear mathematical model representing the influence of the different parameters and their interactions was obtained. The parametric study showed that efficiency of the adsorption system (Dyes/ Holocellulose) is mainly linked to pH variation. The best yields were observed for MB at pH=10 and for MO at pH=2.The kinetic data was analyzed using different models , namely , the pseudo

Interfacial adsorption of insulin - Conformational changes and reversibility of adsorption

NARCIS (Netherlands)

Mollmann, SH; Jorgensen, L; Bukrinsky, JT; Elofsson, U; Norde, W; Frokjaer, S

The adsorption of human insulin to Teflon particles was studied with respect to conformational changes and the reversibility of adsorption was examined by total internal reflection fluorescence (TIRF). Adsorption isotherms for the adsorption of human insulin indicated high affinity adsorption, even

Adsorption induced losses in interfacial cohesion

International Nuclear Information System (INIS)

Asaro, R.J.

1977-07-01

A model for interfacial cohesion is developed which describes the loss in the strength of an interface due to the segregation and adsorption of impurities on it. Distinctions are made between interface separations that occur too rapidly for any significant redistribution of adsorbing matter to take place and separations that are slow enough to allow full adsorption equilibrium. Expressions for the total work of complete decohesion are presented for both cases. The results are applied to well-known model adsorption isotherms and some experimental data for grain boundary adsorption of phosphorus in iron is analyzed with respect to the losses in intergranular cohesion

Adsorption and activation of methane and methanol on Pt(100) surface: a density functional study; Adsorption et activation du methane et du methanol sur la surface (100) du platine: une etude par la fonctionnelle de la densite

Energy Technology Data Exchange (ETDEWEB)

Moussounda, P.S

2006-11-15

The activation of methane (CH{sub 4}) and methanol (CH{sub 3}OH) on Pt(100) surface has been investigated using density functional theory calculations based on plane-wave basis and pseudo-potential. We optimised CH{sub 4}/Pt(100) system. The calculated adsorption energies over the top, bridge and hollow sites are small, weakly dependent on the molecular orientation. The nature of the CH{sub 4}-Pt interaction was examined through the electronic structure changes. The adsorption of methyl (CH{sub 3}) and hydrogen (H) and the co-adsorption of CH{sub 3}+H were also calculated. From these results, we examined the dissociation of CH{sub 4} to CH{sub 3}+H, and the activation energies found are in good agreement with the experimental and theoretical values. The activation of CH{sub 3}OH/Pt(100) has been studied. All the sites have almost the same adsorption energy. The adsorption of oxygen (O) and the co-adsorption of CH{sub 4} and O were also examined. In addition, the formation of CH{sub 3}OH assuming a one-step mechanism step via the co-adsorption of CH{sub 4}+O has been studied and the barrier height was found to be high. (authors)

Adsorption characteristics of siloxanes in landfill gas by the adsorption equilibrium test.

Science.gov (United States)

Nam, Sangchul; Namkoong, Wan; Kang, Jeong-Hee; Park, Jin-Kyu; Lee, Namhoon

2013-10-01

Due to the increase in energy cost by constantly high oil prices and the obligation to reduce greenhouse effect gases, landfill gas is frequently used as an alternative energy source for producing heat and electricity. Most of landfill gas utility facilities, however, are experiencing problems controlling siloxanes from landfill gas as their catalytic oxidizers are becoming fouled by silicon dioxide dust. To evaluate adsorption characteristics of siloxanes, an adsorption equilibrium test was conducted and parameters in the Freundlich and Langmuir isotherms were analyzed. Coconut activated carbon (CA1), coal activated carbon (CA2), impregnated activated carbon (CA3), silicagel (NCA1), and activated alumina (NCA2) were used for the adsorption of the mixed siloxane which contained hexamethyldisiloxane (L2), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). L2 had higher removal efficiency in noncarbon adsorbents compared to carbon adsorbents. The application of Langmuir and Freundlich adsorption isotherm demonstrated that coconut based CA1 and CA3 provided higher adsorption capacity on L2. And CA2 and NCA1 provided higher adsorption capacity on D4 and D5. Based on the experimental results, L2, D4, and D5 were converted by adsorption and desorption in noncarbon adsorbents. Adsorption affinity of siloxane is considered to be affect by the pore size distribution of the adsorbents and by the molecular size of each siloxane. Copyright © 2013 Elsevier Ltd. All rights reserved.

Study of the secondary electron energy spectrum of clean aluminium modification during oxygen adsorption, hydrogen adsorption or carbon segregation

International Nuclear Information System (INIS)

Pellerin, Francois

1981-01-01

The first part of this work is a review of both theoretical and experimental aspects of the fine structure appearing in the Secondary Electron Spectrum (SES) and in the electron energy loss spectrum. In the second part, we report the results of a study of the SES and ELS spectra of clean and gas covered aluminium. The use of very low primary electron energies (E p ≤ 30 eV) enables the detection of previously unobserved peaks in the ELS spectra of clean and oxygen covered aluminium. They are attributed to single electron excitations. Furthermore, a very large peak appears in the SES spectrum during oxygen or carbon adsorption on aluminium. It is interpreted in terms of interaction of the background electrons with the valence electrons of the surface. Molecular hydrogen adsorption is observed on Ta, Pt, Al 2 O 3 , Si. It is responsible for an ELS peak located 13 eV below the elastic peak. Furthermore, on silicon, the chemisorbed hydrogen form can be distinguished from the molecular form with the help of ELS. Finally, some examples are given of the application of these results to surface imaging. (author) [fr

Ethanol mediated As(III) adsorption onto Zn-loaded pinecone biochar: Experimental investigation, modeling, and optimization using hybrid artificial neural network-genetic algorithm approach.

Science.gov (United States)

Zafar, Mohd; Van Vinh, N; Behera, Shishir Kumar; Park, Hung-Suck

2017-04-01

Organic matters (OMs) and their oxidization products often influence the fate and transport of heavy metals in the subsurface aqueous systems through interaction with the mineral surfaces. This study investigates the ethanol (EtOH)-mediated As(III) adsorption onto Zn-loaded pinecone (PC) biochar through batch experiments conducted under Box-Behnken design. The effect of EtOH on As(III) adsorption mechanism was quantitatively elucidated by fitting the experimental data using artificial neural network and quadratic modeling approaches. The quadratic model could describe the limiting nature of EtOH and pH on As(III) adsorption, whereas neural network revealed the stronger influence of EtOH (64.5%) followed by pH (20.75%) and As(III) concentration (14.75%) on the adsorption phenomena. Besides, the interaction among process variables indicated that EtOH enhances As(III) adsorption over a pH range of 2 to 7, possibly due to facilitation of ligand-metal(Zn) binding complexation mechanism. Eventually, hybrid response surface model-genetic algorithm (RSM-GA) approach predicted a better optimal solution than RSM, i.e., the adsorptive removal of As(III) (10.47μg/g) is facilitated at 30.22mg C/L of EtOH with initial As(III) concentration of 196.77μg/L at pH5.8. The implication of this investigation might help in understanding the application of biochar for removal of various As(III) species in the presence of OM. Copyright © 2016. Published by Elsevier B.V.

Adsorption Characteristics of Polyvinyl Alcohols in Solution on Expanded Graphite

Directory of Open Access Journals (Sweden)

Xiu-Yan Pang

2012-01-01

Full Text Available Expanded graphite (EG adsorbent was prepared with 50 mesh graphite as raw materials, potassium permanganate as oxidant, and vitriol as intercalation compound. Three kinds of polyvinyl alcohol (PVA with different degree of polymerization (DP in aqueous solution were used as adsorbates. We have studied the influence of initial PVA concentration, temperature and ionic strength on adsorption capacity. Langmuir constants and Gibbs free energy change (⊿G° were calculated according to experimental data respectively. Thermodynamic analysis indicates the equilibrium adsorbance of PVA on EG increase with the rise of SO42– concentration. Adsorption isotherms of PVA with different degree of polymerization are all types and we deduce PVA molecules lie flat on EG surface. Adsorption processes are all spontaneous. Kinetic studies show that the kinetic data can be described by pseudo second-order kinetic model. Second-order rate constants and the initial adsorption rate rise with the increasing of temperature and half-adsorption time decreases with the increasing of temperature. The adsorption activation energy of each PVA is less than 20 kJ•mol−1, physical adsorption is the major mode of the overall adsorption process.

Adsorption of sunset yellow FCF from aqueous solution by chitosan-modified diatomite.

Science.gov (United States)

Zhang, Y Z; Li, J; Li, W J; Li, Y

2015-01-01

Sunset yellow (SY) FCF is a hazardous azo dye pollutant found in food processing effluent. This study investigates the use of diatomaceous earth with chitosan (DE@C) as a modified adsorbent for the removal of SY from wastewater. Fourier transform infrared spectroscopy results indicate the importance of functional groups during the adsorption of SY. The obtained N2 adsorption-desorption isotherm values accord well with IUPAC type II. Our calculations determined a surface area of 69.68 m2 g(-1) for DE@C and an average pore diameter of 4.85 nm. Using response surface methodology, optimized conditions of process variables for dye adsorption were achieved. For the adsorption of SY onto DE@C, this study establishes mathematical models for the optimization of pH, contact time and initial dye concentration. Contact time plays a greater role in the adsorption process than either pH or initial dye concentration. According to the adjusted correlation coefficient (adj-R2>0.97), the models used here are suitable for illustration of the adsorption process. Theoretical experimental conditions included a pH of 2.40, initial dye concentration of 113 mg L(-1) and 30.37 minutes of contact time. Experimental values for the adsorption rate (92.54%) were close to the values predicted by the models (95.29%).

Adsorption of cellulase on cellulolytic enzyme lignin from lodgepole pine.

Science.gov (United States)

Tu, Maobing; Pan, Xuejun; Saddler, Jack N

2009-09-09

Enzymatic hydrolysis of lignocellulosic materials is significantly affected by cellulase adsorption onto the lignocellulosic substrates and lignin. The presence of lignin plays an important role in lignocellulosic hydrolysis and enzyme recycling. Three cellulase preparations (Celluclast, Spezyme CP, and MSUBC) were evaluated to determine their adsorption onto cellulolytic enzyme lignin (CEL) from steam-exploded Lodgepole pine (SELP) and ethanol (organosolv)-pretreated Lodgepole pine (EPLP). The adsorption affinity of cellulase (Celluclast) onto isolated lignin (CEL-EPLP and CEL-SELP) was slightly higher than that from corresponding EPLP and SELP substrates on the basis of the Langmuir constants. Effects of temperature, ionic strength, and surfactant on cellulase adsorption onto isolated lignin were also explored in this study. Thermodynamic analysis of enzyme adsorption onto isolated lignin (Gibbs free energy change DeltaG(0) approximately -30 kJ/mol) indicated this adsorption was a spontaneous process. The addition of surfactant (0.2% w/v) could reduce the adsorption of cellulase onto CEL-SELP by 60%. Two types of adsorption isotherm were compared for cellulase adsorption onto isolated lignin. A Langmuir adsorption isotherm showed better fit for the experimental data than a Freundlich adsorption isotherm.

Statistical mechanics of binary mixture adsorption in metal-organic frameworks in the osmotic ensemble

Science.gov (United States)

Dunne, Lawrence J.; Manos, George

2018-03-01

Although crucial for designing separation processes little is known experimentally about multi-component adsorption isotherms in comparison with pure single components. Very few binary mixture adsorption isotherms are to be found in the literature and information about isotherms over a wide range of gas-phase composition and mechanical pressures and temperature is lacking. Here, we present a quasi-one-dimensional statistical mechanical model of binary mixture adsorption in metal-organic frameworks (MOFs) treated exactly by a transfer matrix method in the osmotic ensemble. The experimental parameter space may be very complex and investigations into multi-component mixture adsorption may be guided by theoretical insights. The approach successfully models breathing structural transitions induced by adsorption giving a good account of the shape of adsorption isotherms of CO2 and CH4 adsorption in MIL-53(Al). Binary mixture isotherms and co-adsorption-phase diagrams are also calculated and found to give a good description of the experimental trends in these properties and because of the wide model parameter range which reproduces this behaviour suggests that this is generic to MOFs. Finally, a study is made of the influence of mechanical pressure on the shape of CO2 and CH4 adsorption isotherms in MIL-53(Al). Quite modest mechanical pressures can induce significant changes to isotherm shapes in MOFs with implications for binary mixture separation processes. This article is part of the theme issue `Modern theoretical chemistry'.

Study of neon adsorption on carbon nanocones using molecular dynamics simulation

International Nuclear Information System (INIS)

Majidi, R.; Ghafoori Tabrizi, K.

2010-01-01

We have used molecular dynamics simulation to study Ne adsorption on carbon nanocones. Adsorption isotherms were obtained at several temperatures between 22.67 and 49.82 K. Adsorption coverage, isosteric heat, and binding energy were calculated. Adsorption was observed both inside and outside of an individual carbon nanocone. The results indicate that the saturation coverage and saturation pressure depend on temperature. At saturation conditions, the maximum values of interior and exterior coverages are 0.17 and 0.39 neon per carbon, respectively. The results are compared to Ne adsorption on open-ended single-walled carbon nanotubes. It is found that adsorption coverages on carbon nanocones are greater than those on carbon nanotubes. The isosteric heat and binding energy of neon adsorption on nanocones indicate that nanocones and nanotubes have highly desirable characteristics as an adsorbent.

Study of neon adsorption on carbon nanocones using molecular dynamics simulation

Energy Technology Data Exchange (ETDEWEB)

Majidi, R. [Department of Physics, Shahid Beheshti University, G.C., Evin, Tehran 19839-63113 (Iran, Islamic Republic of); Ghafoori Tabrizi, K., E-mail: k-tabrizi@sbu.ac.i [Department of Physics, Shahid Beheshti University, G.C., Evin, Tehran 19839-63113 (Iran, Islamic Republic of)

2010-04-15

We have used molecular dynamics simulation to study Ne adsorption on carbon nanocones. Adsorption isotherms were obtained at several temperatures between 22.67 and 49.82 K. Adsorption coverage, isosteric heat, and binding energy were calculated. Adsorption was observed both inside and outside of an individual carbon nanocone. The results indicate that the saturation coverage and saturation pressure depend on temperature. At saturation conditions, the maximum values of interior and exterior coverages are 0.17 and 0.39 neon per carbon, respectively. The results are compared to Ne adsorption on open-ended single-walled carbon nanotubes. It is found that adsorption coverages on carbon nanocones are greater than those on carbon nanotubes. The isosteric heat and binding energy of neon adsorption on nanocones indicate that nanocones and nanotubes have highly desirable characteristics as an adsorbent.

Adsorption of heavy metal ions on activated carbon, (5)

International Nuclear Information System (INIS)

Yoshida, Hisayoshi; Kamegawa, Katsumi; Arita, Seiji

1978-01-01

The adsorption effect of heavy metal ions Cd 2+ , Zn 2+ and Hg 2+ on activated carbon by adding EDTA is reported, utilizing the experimental data. The activated carbons used for the experiment are mostly D, and B, C and F partly. As for the experimental procedure, the solutions of 100 ml which are composed of activated carbon, pH adjusting liquid, EDTA solution and solutions of heavy metals Cd, Zn and Hg, are shaken for 24 hours at 20 deg C, and after the activated carbon is centrifuged and separated for 15 minutes at 3000 rpm, the remaining heavy metal concentrations and pH in the supernatant are measured. The experimental results showed the useful effect on the adsorption of heavy metal ions of Cd, Zn and Hg by adding about 1 mol ratio of (EDTA/heavy metals). The individual experimental results are presented in detail. Concerning the adsorption quantity, 83% of Cd ions remained in the supernatant without addition of EDTA, but less than 1% with addition of about 1 to 5 mol ratio of (EDTA/Cd), and this adsorption effect was almost similar to Zn and Hg, i.e. 100% to 1% in Zn and 70% to 2 or 3% in Hg, under the condition written above. As for the influence of pH on Cd adsorption, the remaining Cd ratio is less than 10%, when pH is 7 to 10.5 at the mol ratio of 1 and 5.5 to 9 at the mol ratio of 10. The adsorption effect was different according to the kinds of activated carbon. The influencing factors for adsorption effect are the concentration of coexisting cations in the solution and the mixing time, etc. The effects of pH on Zn and Hg adsorption were almost similar to Cd. (Nakai, Y.)

Methylene blue adsorption from aqueous solution by dehydrated peanut hull

Energy Technology Data Exchange (ETDEWEB)

Ozer, Dursun [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey); Dursun, Guelbeyi [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)]. E-mail: gdursun@firat.edu.tr; Ozer, Ahmet [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)

2007-06-01

Dyes are colour organic compounds which can colorize the other substances. These substances usually presents in the effluent water of many industries, such as textiles, leather, paper, printing and cosmetics. To observe the potential feasibility of removing colour, peanut hull as an agricultural by-product was dehydrated with sulphuric acid (DPH) and used for adsorption of methylene blue (MB) from aqueous solution. The effects of various parameters such as initial methylene blue concentrations, temperatures and particle sizes were examined and optimal experimental conditions were determined. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich model as well. The adsorption process followed the pseudo-second order kinetic model. The mass transfer model as intraparticle diffusion was applied to the experimental data to examine the mechanisms of rate controlling step. It was found that at the higher initial MB concentration, intraparticle diffusion is becoming significant controlling step. The thermodynamic constants of the adsorption process were also evaluated by using the Langmuir constants related to the equilibrium of adsorption at different temperatures. The results in this study indicated that dehydrated peanut hull was a good adsorbent for removing methylene blue.

Theoretical study of hydrogen adsorption of graphene and carbon nanotubes decorated with palladium

International Nuclear Information System (INIS)

Lopez Corral, Ignacio; German, Estefania; Volpe, Maria A; Brizuela, Graciela; Juan, Alfredo

2008-01-01

Since their discovery in 1991, carbon nanotubes (CNT) have awakened great interest in materials science thanks to their extraordinary structural, electronic and mechanical properties which facilitate their application in many different areas. One of the most promising applications is the possibility of using CNT to store hydrogen for use in small scale fuel cells. Unfortunately, experimental studies performed some years ago have often led to controversial conclusions, causing a continuing debate that has still not been resolved. The most recent work suggests that the storage of hydrogen for practical purposes can be achieved with CNT decorated with transition metals, for example Pd. In this context, theoretical modeling methods have to be used for a detailed understanding of the influence and scope of this type of modification in the interaction of the nanotubes with atomic or molecular hydrogen. This work studied hydrogen adsorption in single-walled carbon nanotubes (SWCNT) doped with Pd atoms, using density functional theory (DFT) and semi-empirical methods. As a preliminary approximation to the system a graphene sheet was used, modeled with a 190 atom cluster of C in a hexagonal arrangement, on which a single Pd atom was placed in adsorption sites. Then C 190 clusters were used to simulate two different types of SWCNT: the zigzag SWCNT of quirality (10.0) and the armchair SWCNT of quirality (5.5), both decorated similarly on the graphene. Geometric optimization procedures for the system's different components were carried out with these models, and then the changes produced during the adsorption process in the electronic occupation of atomic orbitals and unions, for which crystal orbital overlap population (COOP) curves and overlap population (OP) values were evaluated. The results obtained with the graphene and nanotube approximations are in agreement and show that the SWCNT modified with Pd have more capacity to trap hydrogen than the non doped SWCNT. The

Adsorption of Pb(II) present in aqueous solution on calcium, strontium and barium hydroxy apatites

International Nuclear Information System (INIS)

Vilchis G, J.

2013-01-01

Calcium, strontium and barium hydroxy apatites were successfully synthesized by chemical precipitation method, the obtained powders were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (Sem), semi-quantitative elemental analysis (EDS), infrared spectroscopy (IR), and N 2 physisorption studies, complementary to these analytical techniques, was determined the surface fractal dimension (Df), and the amount of surface active sites of the materials, in order to know application as ceramic for water remediation. The ability of Pb(II) ion adsorption present in aqueous solution on the hydroxy apatites synthesized by batch type experiments was studied as a function of contact time, concentration of the adsorbate and temperature. The maximum lead adsorption efficiencies obtained were 0.31, 0.32 and 0.26 mg/g for calcium, strontium and barium hydroxy apatites respectively, achieved an equilibrium time of 20 minutes in the three solid-liquid systems studied. Experimental data were adequately adjusted at the adsorption kinetic model pseudo-second order, for the three cases. Moreover, experimental data of the strontium and calcium hydroxy apatites were adjusted to the Langmuir adsorption isotherm, indicating that the adsorption was through a monolayer, whereas barium hydroxyapatite was adjusted to the Freundlich adsorption isotherm, indicating a multilayer adsorption. The thermodynamic parameters obtained during adsorption studies as a function of temperature showed physisorption, exothermic and spontaneous processes respectively. The results showed that the calcium hydroxyapatite, strontium and barium are an alternative for the Pb(II) ion adsorption present in wastewaters. (Author)

Computational study of ibuprofen removal from water by adsorption in realistic activated carbons.

Science.gov (United States)

Bahamon, Daniel; Carro, Leticia; Guri, Sonia; Vega, Lourdes F

2017-07-15

Molecular simulations using the Grand Canonical Monte Carlo (GCMC) method have been performed in order to obtain physical insights on how the interaction between ibuprofen (IBP) and activated carbons (ACs) in aqueous mixtures affects IBP removal from water by ACs. A nanoporous carbon model based on units of polyaromatic molecules with different number of rings, defects and polar-oxygenated sites is described. Individual effects of factors such as porous features and chemical heterogeneities in the adsorbents are investigated and quantified. Results are in good agreement with experimental adsorption data, highlightening the ability of GCMC simulation to describe the macroscopic adsorption performance in drug removal applications, while also providing additional insights into the IBP/water adsorption mechanism. The simulation results allow finding the optimal type of activated carbon material for separating this pollutant in water treatment. Copyright © 2017 Elsevier Inc. All rights reserved.

Theoretical study of adsorption of lithium atom on carbon nanotube

Directory of Open Access Journals (Sweden)

Masato Senami

2011-12-01

Full Text Available We investigate the adsorption of lithium atoms on the surface of the (12,0 single wall carbon nanotube (SWCNT by using ab initio quantum chemical calculations. The adsorption of one lithium atom on the inside of this SWCNT is favored compared to the outside. We check this feature by charge transfer and regional chemical potential density. The adsorption of multiple lithium atoms on the interior of the SWCNT is studied in terms of adsorption energy and charge transfer. We show that repulsive force between lithium atoms destabilizes a system for the large number of lithium atoms.

Adsorption behavior of strontium on binary mineral mixtures of Montmorillonite and Kaolinite

Energy Technology Data Exchange (ETDEWEB)

Bascetin, Elvan [Cekmece Nuclear Research and Training Center, P.K.1 34149, Atatuerk Airport, Istanbul (Turkey); Atun, Guelten [Engineering Faculty, Chemistry Department, Istanbul University, 34850 Avcilar, Istanbul (Turkey)]. E-mail: gultena@istanbul.edu.tr

2006-08-15

The adsorption behavior of kaolinite and montmorillonite minerals and their mixtures in respect of Sr ion were studied by means of a batch method using {sup 90}Sr as a radio tracer. The effect of several parameters such as temperature, pH, Sr concentration and supporting electrolyte were investigated. Experimentally measured distribution coefficients showed a good agreement to within 98.5-99.7% with theoretically calculated values. The values of adsorption capacity of adsorbents and mean adsorption energy of adsorption were calculated by fitting the adsorption data to Dubinin-Radushkevich isotherm. The adsorption capacity of clay mixtures decreased as kaolinite fractions increased. The mean adsorption energy values of 8.0-9.5 kJ mol{sup -1} showed that adsorption was governed by ion exchange. The Freundlich parameters were used to characterize a site distribution function for binary exchange between Sr and Na.

Adsorption behavior of strontium on binary mineral mixtures of Montmorillonite and Kaolinite

International Nuclear Information System (INIS)

Bascetin, Elvan; Atun, Guelten

2006-01-01

The adsorption behavior of kaolinite and montmorillonite minerals and their mixtures in respect of Sr ion were studied by means of a batch method using 90 Sr as a radio tracer. The effect of several parameters such as temperature, pH, Sr concentration and supporting electrolyte were investigated. Experimentally measured distribution coefficients showed a good agreement to within 98.5-99.7% with theoretically calculated values. The values of adsorption capacity of adsorbents and mean adsorption energy of adsorption were calculated by fitting the adsorption data to Dubinin-Radushkevich isotherm. The adsorption capacity of clay mixtures decreased as kaolinite fractions increased. The mean adsorption energy values of 8.0-9.5 kJ mol -1 showed that adsorption was governed by ion exchange. The Freundlich parameters were used to characterize a site distribution function for binary exchange between Sr and Na

Feasibility study on the application of a heat-pipe type adsorption chiller

Energy Technology Data Exchange (ETDEWEB)

Ahn, Sang Hyeok; Chung, Jae Dong [Dept. of Mechanical Engineering, Sejong University, Seoul (Korea, Republic of); Kwon, Oh Kyung [Energy System R and D Group, Korea Institute of Industrial Technology, Cheonan (Korea, Republic of)

2017-01-15

A parametric study on a heat-pipe type adsorption chiller with SWS-1L (mesoporous silica gel impregnated with CaCl{sub 2}) and water pair was conducted using a numerical method in this research. A heat pipe that is in direct contact with the adsorbent is applied to the adsorption chiller to improve the heat transfer capacity of the adsorption bed. A feasibility study was performed on the heat-pipe type adsorption bed with a single layer. The Coefficient of performance (COP) and the Specific cooling power (SCP) were 0.231 and 844.8 W/kg, respectively. These values are lower than the system performance values of the existing fin-tube type adsorption bed. However, when the number of bed layers was increased to seven, the COP and SCP of the heat-pipe type adsorption bed were 0.520 and 752.4 W/kg, respectively. These values are 5.25 % and 39.8 % higher than the COP and SCP, respectively, of the fin-tube type adsorption bed. These findings indicate that the heat-pipe type adsorption bed can potentially address the disadvantage caused by the system size of the adsorption chiller. A parametric study was also conducted for six design parameters, namely, number of layers, heat pipe pitch, heat pipe radius, fin width, fin spacing, and hot water temperature.

Feasibility study on the application of a heat-pipe type adsorption chiller

International Nuclear Information System (INIS)

Ahn, Sang Hyeok; Chung, Jae Dong; Kwon, Oh Kyung

2017-01-01

A parametric study on a heat-pipe type adsorption chiller with SWS-1L (mesoporous silica gel impregnated with CaCl_2) and water pair was conducted using a numerical method in this research. A heat pipe that is in direct contact with the adsorbent is applied to the adsorption chiller to improve the heat transfer capacity of the adsorption bed. A feasibility study was performed on the heat-pipe type adsorption bed with a single layer. The Coefficient of performance (COP) and the Specific cooling power (SCP) were 0.231 and 844.8 W/kg, respectively. These values are lower than the system performance values of the existing fin-tube type adsorption bed. However, when the number of bed layers was increased to seven, the COP and SCP of the heat-pipe type adsorption bed were 0.520 and 752.4 W/kg, respectively. These values are 5.25 % and 39.8 % higher than the COP and SCP, respectively, of the fin-tube type adsorption bed. These findings indicate that the heat-pipe type adsorption bed can potentially address the disadvantage caused by the system size of the adsorption chiller. A parametric study was also conducted for six design parameters, namely, number of layers, heat pipe pitch, heat pipe radius, fin width, fin spacing, and hot water temperature

Liquid phase adsorption behavior of inulin-type fructan onto activated charcoal.

Science.gov (United States)

Li, Kecheng; Liu, Song; Xing, Ronge; Yu, Huahua; Qin, Yukun; Li, Pengcheng

2015-05-20

This study describes liquid phase adsorption characteristics of inulin-type fructan onto activated charcoal. Batch mode experiments were conducted to study the effects of pH, contact time, temperature and initial concentration of inulin. Nearly neutral solution (pH 6-8) was favorable to the adsorption and the equilibrium was attained after 40 min with the maximum adsorption Qmax 0.182 g/g (adsorbate/adsorbent) at 298 K. The experimental data analysis indicated that the adsorption process fitted well with the pseudo-second-order kinetic model (R(2) = 1) and Langmuir isotherms model (R(2) > 0.99). Thermodynamic parameters revealed that the adsorption process was spontaneous and exothermic with a physical nature. Inulin desorption could reach 95.9% using 50% ethanol solution and activated charcoal could be reused without significant losses in adsorption capacity. These results are of practical significance for the application of activated charcoal in the production and purification of inulin-type fructan. Copyright © 2015 Elsevier Ltd. All rights reserved.

Adsorption of methyl iodide on charcoal

International Nuclear Information System (INIS)

Hidajat, K.; Aracil, J.; Kenney, C.N.

1990-01-01

The adsorption of non-radioactive methyl iodide has been measured experimentally over a range of conditions of concentration, and temperature on an activated charcoal. This is of interest since methyl iodide is formed from iodine fission products in gas cooled nuclear reactors. A mathematical model has also been developed which describes the rate of adsorption, under isothermal and linear adsorption isotherm conditions in a recycle adsorber. This model takes into account the resistance to adsorption caused by the surface adsorption, as well as the external and internal mass transfer resistances. The solution to the model for the recycle adsorber was obtained using a semidiscretisation method to reduce the partial differential equations to a system of stiff ordinary differential equations, and the resulting differential equations solved by a standard numerical technique. (author)

CHROMIUM (III ADSORPTION FROM AQUEOUS SOLUTION BY Rhizophora apiculata TANNINS

Directory of Open Access Journals (Sweden)

C. W. Oo

2010-06-01

Full Text Available Adsorption of Cr3+ from aqueous solution by Rhizophora apiculata tannins was investigated in batch shaking experiments. Tannins extracted from R. apiculata mangrove barks was chemically modified with formaldehyde in the basic solution of sodium hydroxide. The performance of the produced adsorbent on the adsorption of Cr3+ was evaluated based on the effect of several parameters like initial pH, adsorbent dosage, initial Cr3+ concentration and contact time. Equilibrium adsorption data was analyzed by Langmuir, Freundlich, Sips and Dubinin-Raduskhevich (D-R isotherms. The fitness of the isotherms to the experimental data was determined by non-linear regression analysis. Adsorption capacity calculated from Langmuir isotherm was found to be 10.14 mg Cr3+/g of adsorbent at optimum adsorption pH of 4.5. Mean energy of adsorption with the value of 10.35 kJ/mol indicated that adsorption Cr3+ on Rhizophora apiculata tannins followed ion-exchange reaction. Kinetic study showed that the adsorption process followed the pseudo second-order kinetic model.   Keywords:  Rhizophora apiculata, tannins, isotherms, kinetic, chromium.

U(VI) adsorption on natural iron-coated sands: comparison of approaches for modeling adsorption on heterogeneous environmental materials

International Nuclear Information System (INIS)

Logue, Brian A.; Smith, Robert W.; Westall, John C.

2004-01-01

Adsorption of U(VI) on 6 samples of natural Fe-rich sands from Oyster, VA was studied over a range of U(VI) concentrations (0.1-100 μM), pH values (3-7.6), and dithionite-citrate-bicarbonate (DCB) extractable amounts of Fe (3.1-12.3 μmol/g). Four modeling approaches were applied to represent the U(VI) adsorption data. Model I was a two-site, diffuse double layer, surface complexation model based on data for synthetic ferrihydrite [Geochim. Cosmochim. Acta 58 (1994) 5465-5478]. Considering the magnitude of approximations necessary for application of the laboratory-based model to natural sands, Model I was surprisingly accurate, as determined by the goodness of fit parameter, χ 2 /N of 53.1-22.2. Model II was based on the reactions and diffuse double layer treatment of Model I, but was calibrated to a portion of U(VI) adsorption data for each sand, and then used to predict adsorption data for the same sand under different experimental conditions. Model II did not increase the accuracy of the predictions made with Model I, χ 2 /N of 42.4-27.6. Models III and IV were four-site affinity spectrum models, without an explicit electric double layer model or explicit surface hydrolysis reactions. Model III was based on a discrete log K spectrum approach, and Model IV was obtained from adjusting all surface stability constants and site concentrations for all surface sites. Models III and IV represented the U(VI) adsorption data with the greatest accuracy, χ 2 /N ranged from 13.8 to 4.4. Model I provides evidence supporting the practice of using pure phase thermodynamic reaction constants for describing the adsorption characteristics of environmentally important sorbents in certain simple cases. Yet, affinity spectrum approaches (Models III and IV) become increasingly important as more accurate interpolation of adsorption data is necessary, the sorbent becomes increasingly complex, or the range of experimental conditions expands

Adsorption studies of a water soluble dye, Reactive Red MF-3B, using sonication-surfactant-modified attapulgite clay

International Nuclear Information System (INIS)

Huang Jianhua; Liu Yuanfa; Jin Qingzhe; Wang Xingguo; Yang Jun

2007-01-01

The removal of water-soluble Reactive Red MF-3B from aqueous media by sonication-surfactant-modified attapulgite clay was studied in a batch system. The surfactant used was octodecyl trimethyl ammonium chloride (OTMAC). Adsorbent characterizations were investigated using X-ray diffraction, infrared spectroscopy, and surface area analysis. The effects of pH, contact time, initial solute concentration, adsorbent dose, and temperature on the adsorption of Reactive Red MF-3B onto modified clay were investigated. On the basis of kinetic studies, specific rate constants involved in the processes were calculated and second-order adsorption kinetics was observed in the case. Film diffusion was found to be the rate-limiting step. Reactive Red MF-3B adsorption was found to increase with increase temperature. The Reactive Red MF-3B equilibrium adsorption data were fitted to Freundlich and Langmuir isotherm models, the former being found to provide the better fit of the experimental data. Thermodynamic parameters were calculated. From the results it can be concluded that the surfactant-modified clay could be a good adsorbent for treating Reactive Red MF-3B-contaminated waters

Arsenic Removal from Water by Adsorption on Iron-Contaminated Cryptocrystalline Graphite

Science.gov (United States)

Yang, Qiang; Yang, Lang; Song, Shaoxian; Xia, Ling

This work aimed to study the feasibility of using iron-contaminated graphite as an adsorbent for As(V) removal from water. The adsorbent was prepared by grinding graphite concentrate with steel ball. The study was performed through the measurements of adsorption capacity, BET surface area and XPS analysis. The experimental results showed that the iron-contaminated graphite exhibited significantly high adsorption capacity of As(V). The higher the iron contaminated on the graphite surface, the higher the adsorption capacity of As(V) on the material obtained. It was suggested that the ion-contaminated graphite was a good adsorbent for As(V) removal.

Binary gas mixture adsorption-induced deformation of microporous carbons by Monte Carlo simulation.

Science.gov (United States)

Cornette, Valeria; de Oliveira, J C Alexandre; Yelpo, Víctor; Azevedo, Diana; López, Raúl H

2018-07-15

Considering the thermodynamic grand potential for more than one adsorbate in an isothermal system, we generalize the model of adsorption-induced deformation of microporous carbons developed by Kowalczyk et al. [1]. We report a comprehensive study of the effects of adsorption-induced deformation of carbonaceous amorphous porous materials due to adsorption of carbon dioxide, methane and their mixtures. The adsorption process is simulated by using the Grand Canonical Monte Carlo (GCMC) method and the calculations are then used to analyze experimental isotherms for the pure gases and mixtures with different molar fraction in the gas phase. The pore size distribution determined from an experimental isotherm is used for predicting the adsorption-induced deformation of both pure gases and their mixtures. The volumetric strain (ε) predictions from the GCMC method are compared against relevant experiments with good agreement found in the cases of pure gases. Copyright © 2018 Elsevier Inc. All rights reserved.

Doping as a means to probe the potential dependence of dopamine adsorption on carbon-based surfaces: A first-principles study

Science.gov (United States)

Aarva, Anja; Laurila, Tomi; Caro, Miguel A.

2017-06-01

In this work, we study the adsorption characteristics of dopamine (DA), ascorbic acid (AA), and dopaminequinone (DAox) on carbonaceous electrodes. Our goal is to obtain a better understanding of the adsorption behavior of these analytes in order to promote the development of new carbon-based electrode materials for sensitive and selective detection of dopamine in vivo. Here we employ density functional theory-based simulations to reach a level of detail that cannot be achieved experimentally. To get a broader understanding of carbonaceous surfaces with different morphological characteristics, we compare three materials: graphene, diamond, and amorphous carbon (a-C). Effects of solvation on adsorption characteristics are taken into account via a continuum solvent model. Potential changes that take place during electrochemical measurements, such as cyclic voltammetry, can also alter the adsorption behavior. In this study, we have utilized doping as an indirect method to simulate these changes by shifting the work function of the electrode material. We demonstrate that sp2- and sp3-rich materials, as well as a-C, respond markedly different to doping. Also the adsorption behavior of the molecules studied here differs depending on the surface material and the change in the surface potential. In all cases, adsorption is spontaneous, but covalent bonding is not detected in vacuum. The aqueous medium has a large effect on the adsorption behavior of DAox, which reaches its highest adsorption energy on diamond when the potential is shifted to more negative values. In all cases, inclusion of the solvent enhances the charge transfer between the slab and DAox. Largest differences in adsorption energy between DA and AA are obtained on graphene. Gaining better understanding of the behavior of the different forms of carbon when used as electrode materials provides a means to rationalize the observed complex phenomena taking place at the electrodes during electrochemical oxidation

Adsorptive removal of organics from aqueous phase by acid-activated coal fly ash: preparation, adsorption, and Fenton regenerative valorization of "spent" adsorbent.

Science.gov (United States)

Wang, Nannan; Hao, Linlin; Chen, Jiaqing; Zhao, Qiang; Xu, Han

2018-05-01

Raw coal fly ash was activated to an adsorbent by sulfuric acid impregnation. The activation condition, the adsorption capacity, and the regenerative valorization of the adsorbent were studied. The results show that the optimal preparation conditions of the adsorbent are [H 2 SO 4 ] = 1 mol L -1 , activation time = 30 min, the ratio of coal fly ash to acid = 1:20 (g:mL), calcination temperature = 100 °C. The adsorption of p-nitrophenol on the adsorbent accords with the pseudo-second-order kinetic equation and the adsorption rate constant is 0.089 g mg -1  min -1 . The adsorption on this adsorbent can be considered enough after 35 min, when the corresponding adsorption capacity is 1.07 mg g -1 (85.6% of p-nitrophenol removal). Compared with raw coal fly ash, the adsorbent has a stable adsorption performance at low pH range (pH = 1-6) and the adsorption of p-nitrophenol is an exothermic process. Ninety minutes is required for the regenerative valorization of saturated adsorbent by Fenton process. The regenerative valorization for this saturated adsorbent can reach 89% under the optimal proposed conditions (30 °C, pH = 3, [H 2 O 2 ] = 5.0 mmol L -1 , [Fe 2+ ] = 5.5 mmol L -1 ). Within 15 experimental runs, the adsorbent has a better and better stability with the increase of experimental runs. Finally, the mechanism of activating coal fly ash is proposed, being verified by the results of the SEM and BET test.

The mechanism of uranium adsorption on Resin 508 and isoelectric point of the resin

International Nuclear Information System (INIS)

Han Qingping; Lu Weichang; Su Huijuan; Hu Jinbo; Zhang Liqin; Chen Banglin

1990-01-01

The adsorption process of uranium by Resin 508 at the solid-liquid interface was investigated and the mechanism of uranium adsorption including adsorption dynamics, adsorption thermodynamics and isoelectric point of resin was studied. The results are as follows: The maximum of uranium adsorption is attained at pH5-7; Uranium adsorption isotherm by Resin 508 in experimental conditions agrees with Langmuir's adsorption isotherm, the maximum of uranium adsorbed (Vm) is 716 mg U/g-dried resin; The adsorption of uranium by Resin 508 is an endothermic reaction and ΔH = 16.87 kJ/mol; The exchange-adsorption rate is mainly controlled by liquid film diffusion; The isoelectric points of Resin 508 before and after uranium adsorption are found to be pH7.5 and pH5.7 respectively. It is a specific adsorption for uranium

Adsorption of volatile organic compounds by pecan shell- and almond shell-based granular activated carbons.

Science.gov (United States)

Bansode, R R; Losso, J N; Marshall, W E; Rao, R M; Portier, R J

2003-11-01

The objective of this research was to determine the effectiveness of using pecan and almond shell-based granular activated carbons (GACs) in the adsorption of volatile organic compounds (VOCs) of health concern and known toxic compounds (such as bromo-dichloromethane, benzene, carbon tetrachloride, 1,1,1-trichloromethane, chloroform, and 1,1-dichloromethane) compared to the adsorption efficiency of commercially used carbons (such as Filtrasorb 200, Calgon GRC-20, and Waterlinks 206C AW) in simulated test medium. The pecan shell-based GACs were activated using steam, carbon dioxide or phosphoric acid. An almond shell-based GAC was activated with phosphoric acid. Our results indicated that steam- or carbon dioxide-activated pecan shell carbons were superior in total VOC adsorption to phosphoric acid-activated pecan shell or almond shell carbons, inferring that the method of activation selected for the preparation of activated carbons affected the adsorption of VOCs and hence are factors to be considered in any adsorption process. The steam-activated, pecan shell carbon adsorbed more total VOCs than the other experimental carbons and had an adsorption profile similar to the two coconut shell-based commercial carbons, but had greater adsorption than the coal-based commercial carbon. All the carbons studied adsorbed benzene more effectively than the other organics. Pecan shell, steam-activated and acid-activated GACs showed higher adsorption of 1,1,1-trichloroethane than the other carbons studied. Multivariate analysis was conducted to group experimental carbons and commercial carbons based on their physical, chemical, and adsorptive properties. The results of the analysis conclude that steam-activated and acid-activated pecan shell carbons clustered together with coal-based and coconut shell-based commercial carbons, thus inferring that these experimental carbons could potentially be used as alternative sources for VOC adsorption in an aqueous environment.

Adsorption of lead from aqueous solutions by poly (methyl methacrylate)

International Nuclear Information System (INIS)

Din, M.; Hussain, R.

1992-01-01

The adsorption capability of commercially manufactured poly (methyl methacrylate) for lead in aqueous medium has been investigated. Percent adsorption and distribution coefficient values have been determined in relation to the shaking time, amount of adsorbent, pH effects and concentration of lead in the solution. The experimental results are compatible with Freundlich type of adsorption behavior. It is discernible from the experimental results that poly (methyl methacrylate) can be used for the removal of lead from slightly acidic aqueous solutions. (author)

Use of activated carbon adsorption in conjunction with radiation treatment processes

International Nuclear Information System (INIS)

Dickson, L.W.; Lopata, V.J.; Toft-Hall, A.; Kremers, W.; Singh, A.

1988-01-01

This report presents the results of an assessment of the potential applications of combined adsorption-irradiation treatment processes. The rationale for the study was to determine whether the cost of radiation treatment could be reduced by concentrating target species on an adsorbent in the radiation field. Several different studies on adsorption-irradiation treatment were identified in the literature, and experimental work was done on both the conversion of sulphur dioxide to elemental sulphur, and the removal of trihalomethanes from water by adsorption on activated carbon and subsequent irradiation. Adsorption-irradiation treatment would appear to be less costly than irradiation alone for radiolytic decomposition of target species at low concentration in liquid streams, in the presence of high-surface-area, electrically insulating adsorbents. 116 refs

Phosphate adsorption from wastewater using zirconium (IV) hydroxide: Kinetics, thermodynamics and membrane filtration adsorption hybrid system studies.

Science.gov (United States)

Johir, M A H; Pradhan, M; Loganathan, P; Kandasamy, J; Vigneswaran, S

2016-02-01

Excessive phosphate in wastewater should be removed to control eutrophication of water bodies. The potential of employing amorphous zirconium (Zr) hydroxide to remove phosphate from synthetic wastewater was studied in batch adsorption experiments and in a submerged membrane filtration adsorption hybrid (MFAH) reactor. The adsorption data satisfactorily fitted to Langmuir, pseudo-first order and pseudo-second order models. Langmuir adsorption maxima at 22 °C and pHs of 4.0, 7.1, and 10.0 were 30.40, 18.50, and 19.60 mg P/g, respectively. At pH 7.1 and temperatures of 40 °C and 60 °C, they were 43.80 and 54.60 mg P/g, respectively. The thermodynamic parameters, ΔG° and ΔS° were negative and ΔH° was positive. FTIR, zeta potential and competitive phosphate, sulphate and nitrate adsorption data showed that the mechanism of phosphate adsorption was inner-sphere complexation. In the submerged MFAH reactor experiment, when Zr hydroxide was added at doses of 1-5 g/L once only at the start of the experiment, the removal of phosphate from 3 L of wastewater containing 10 mg P/L declined after 5 h of operation. However, when Zr hydroxide was repeatedly added at 5 g/L dose every 24 h, satisfactory removal of phosphate was maintained for 3 days. Copyright © 2015 Elsevier Ltd. All rights reserved.

Nitrate Adsorption on Clay Kaolin: Batch Tests

Directory of Open Access Journals (Sweden)

Morteza Mohsenipour

2015-01-01

Full Text Available Soils possessing kaolin, gibbsite, goethite, and hematite particles have been found to have a natural capacity to attenuate pollution in aqueous phase. On the other hand, the hydroxyl group in soil increases anion exchange capacity under a low pH condition. The main objective of this paper was to evaluate effects of kaolin on nitrate reduction under acidic condition. In order to analyze the kaolin adsorption behaviour under various conditions, four different concentrations of nitrate, 45, 112.5, 225, and 450 mgNO3-/L, with a constant pH equal to 2, constant temperature equal to 25°C, and exposure period varying from 0 to 150 minutes were considered. The capacity of nitrate adsorption on kaolin has also been studied involving two well-known adsorption isotherm models, namely, Freundlich and Longmuir. The results revealed that approximately 25% of the nitrate present in the solution was adsorbed on clay kaolin. The laboratory experimental data revealed that Freundlich adsorption isotherm model was more accurate than Longmuir adsorption model in predicting of nitrate adsorption. Furthermore, the retardation factor of nitrate pollution in saturated zone has been found to be approximately 4 in presence of kaolin, which indicated that kaolin can be used for natural scavenger of pollution in the environment.

Adsorption of cationic dye on a biohybrid SiO2-alginate

International Nuclear Information System (INIS)

Barrón Zambrano, J A; Ávila Ortega, A; Muñoz Rodríguez, D; Carrera Figueiras, C; López-Pérez, A J

2013-01-01

In this work, a biohybrid material based on SiO 2 -alginate was obtained and its properties of adsorption evaluated using methylene blue as a model dye. The experimental results showed that the biohybrid SiO 2 -alginate has a higher adsorption ability compared to their base compounds (SiO 2 and alginate). Methylene blue adsorption is pH dependent, resulting in a maximum adsorption at pH = 8. The sorption kinetics rate is similar to SiO 2 . Kinetic data were fitted to a model of pseudosecond order. The experimental isotherms fit well the Langmuir model.

A density functional study on the adsorption of hydrogen molecule ...

Indian Academy of Sciences (India)

tive adsorption of H2 onto the minimum energy copper clusters by using the density ... theoretical study of molecular oxygen and atomic oxy- gen adsorption onto small ...... the values for all singlet spin states are zero, indicating that no ...

Characterization of ZSM-5 modified with niobium pentoxide: the study of thiophene adsorption

Energy Technology Data Exchange (ETDEWEB)

Cavalcanti, Rodrigo M.; Barros, Ivoneide de C.L., E-mail: ibarros@ufam.edu.br [Universidade Federal do Amazonas (UFAM), Manaus, AM (Brazil). Inst. de Ciencias Exatas; Dias, Jose A.; Dias, Silvia C.L. [Universidade de Brasilia (UnB), DF (Brazil). Inst. de Quimica

2013-01-15

ZSM-5 adsorbents impregnated with Nb{sub 2}O{sub 5} were applied in the sulfur removal in the form of thiophene, refractory substance of difficult removal of liquid fuels. For this purpose, a model fuel containing iso-octane contaminated with thiophene in concentrations of 877.5 to 1155 ppmw was prepared. The samples were characterized by X-ray diffractometry (XRD), Fourier transform infrared (FTIR) and Fourier transform-Raman (FT-Raman) spectroscopies for confirmation of the adsorbents, being prioritized the adsorption study with that containing 5 wt.% of niobium pentoxide, because it showed a greater capacity for removal of thiophene. The best results of adsorption were achieved at 353 K, a longer time to reach equilibrium was observed. Under these conditions, the best kinetic fitting was achieved using the equation of pseudo-second order, demonstrating the domain of the phenomenon of chemisorption. While under lower temperatures, the diffusion model presented a better approximation of the experimental results. Also, the increasing of temperature did enhance spontaneous processes. (author)

Characterization of Ag adsorption on TiC(001) substrate: an ab initio study

International Nuclear Information System (INIS)

Ma Shangyi; Wang Shaoqing

2008-01-01

Ag adsorptions at 0.25–3 monolayer (ML) coverage on a perfect TiC(001) surface and at 0.25 ML coverage on C vacancy are separately investigated by using the pseudopotential-based density functional theory. The preferential adsorption sites and the adsorption-induced modifications of electronic structures of both the substrate and adsorbate are analysed. Through the analyses of adsorption energy, ideal work of separation, interface distance, projected local density of states, and the difference electron density, the characteristic evolution of the adatom-surface bonding as a function of the amount of deposited silver is studied. The nature of the Ag/TiC bonding changes as the coverage increases from 0.25 to 3 MLs. Unlike physisorption in an Ag/MgO system, polar covalent component contributes to the Ag/TiC interfacial adhesion in most cases, however, for the case of 1–3 ML coverage, an additional electrostatic interaction between the absorption layer and the substrate should be taken into account. The value of ideal work of separation, 1.55 J/m 2 for a 3-ML-thick adlayer accords well with other calculations. The calculations predict that Ag does not wet TiC(001) surface and prefers a three-dimensional growth mode in the absence of kinetic factor. This work reports on a clear site and coverage dependence of the measurable physical parameters, which would benefit the understanding of Ag/TiC (001) interface and the analysis of experimental data. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Kinetic and Thermodynamic Studies on Adsorption of Sulphate from ...

African Journals Online (AJOL)

DELL USER

22, No. 1, 2017. 39. Kinetic and Thermodynamic Studies on Adsorption of Sulphate from Aqueous Solution by. Magnetite ... poison catalysts, and affect the .... C for 1 h in a stainless steel reactor placed in a furnace ... N2 gas for 30 min. 50 ml of ...... adsorption for designing and evaluating the ... is the equilibrium liquid-phase.

Contribution of Ash Content Related to Methane Adsorption Behaviors of Bituminous Coals

Directory of Open Access Journals (Sweden)

Yanyan Feng

2014-01-01

Full Text Available Methane adsorption isotherms on coals with varying ash contents were investigated. The textural properties were characterized by N2 adsorption/desorption isotherm at 77 K, and methane adsorption characteristics were measured at pressures up to 4.0 MPa at 298 K, 313 K, and 328 K, respectively. The Dubinin-Astakhov model and the Polanyi potential theory were employed to fit the experimental data. As a result, ash content correlated strongly to methane adsorption capacity. Over the ash range studied, 9.35% to 21.24%, the average increase in methane adsorption capacity was 0.021 mmol/g for each 1.0% rise in ash content. With the increasing ash content range of 21.24%~43.47%, a reduction in the maximum adsorption capacities of coals was observed. In addition, there was a positive correlation between the saturated adsorption capacity and the specific surface area and micropore volume of samples. Further, this study presented the heat of adsorption, the isosteric heat of adsorption, and the adsorbed phase specific heat capacity for methane adsorption on various coals. Employing the proposed thermodynamic approaches, the thermodynamic maps of the adsorption processes of coalbed methane were conducive to the understanding of the coal and gas simultaneous extraction.

Study of polyethyleneimine- and amidoxime-functionalized hybrid biomass of Spirulina (Arthrospira) platensis for adsorption of uranium (VI) ion.

Science.gov (United States)

Bayramoglu, Gulay; Akbulut, Aydin; Arica, M Yakup

2015-11-01

This study investigates the potential application of the polyethyleneimine- (PEI) and amidoxime-modified Spirulina (Arthrospira) platensis biomasses for the removal of uranium ion in batch mode using the native biomass as a control system. The uranium ion adsorption was also characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, zeta potential analysis, and surface area measurement studies. The effects of pH, biomass amount, contact time, initial uranium ion concentration, and ionic strength were evaluated by using native and modified algal biomass preparations. The uranium ion removal was rapid, with more than 70% of total adsorption taking place in 40 min, and equilibrium was established within 60 min. From the experimental data, it was found that the amount of adsorption uranium ion on the algal preparations decreased in the following series: amidoxime-modified algal biomass > PEI-modified algal biomass > native algal biomass. Maximum adsorption capacities of amidoxime- and PEI-modified, and native algal biomasses were found to be 366.8, 279.5, and 194.6 mg/g, respectively, in batchwise studies. The adsorption rate of U(VI) ion by amidoxime-modified algal biomass was higher than those of the native and PEI-modified counterparts. The adsorption processes on all the algal biomass preparations followed by the Dubinin-Radushkevitch (D-R) and Temkin isotherms and pseudo-second-order kinetic models. The thermodynamic parameters were determined at four different temperatures (i.e., 15, 25, 35, and 45 °C) using the thermodynamics constant of the Temkin isotherm model. The ΔH° and ΔG° values of U(VI) ion adsorption on algal preparations show endothermic heat of adsorption; higher temperatures favor the process. The native and modified algal biomass preparations were regenerated using 10 mM HNO3. These results show that amidoxime-modified algal biomass can be a potential candidate for effective removal of U(VI) ion from

Adsorption of water and butanol in silicalite-1 film studied with in situ attenuated total reflectance-Fourier transform infrared spectroscopy.

Science.gov (United States)

Farzaneh, Amirfarrokh; Zhou, Ming; Potapova, Elisaveta; Bacsik, Zoltán; Ohlin, Lindsay; Holmgren, Allan; Hedlund, Jonas; Grahn, Mattias

2015-05-05

Biobutanol produced by, e.g., acetone-butanol-ethanol (ABE) fermentation is a promising alternative to petroleum-based chemicals as, e.g., solvent and fuel. Recovery of butanol from dilute fermentation broths by hydrophobic membranes and adsorbents has been identified as a promising route. In this work, the adsorption of water and butanol vapor in a silicalite-1 film was studied using in situ attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy to better understand the adsorption properties of silicalite-1 membranes and adsorbents. Single-component adsorption isotherms were determined in the temperature range of 35-120 °C, and the Langmuir model was successfully fitted to the experimental data. The adsorption of butanol is very favorable compared to that of water. When the silicalite-1 film was exposed to a butanol/water vapor mixture with 15 mol % butanol (which is the vapor composition of an aqueous solution containing 2 wt % butanol, a typical concentration in an ABE fermentation broth, i.e., the composition of the gas obtained from gas stripping of an ABE broth) at 35 °C, the adsorption selectivity toward butanol was as high as 107. These results confirm that silicalite-1 quite selectively adsorbs hydrocarbons from vapor mixtures. To the best of our knowledge, this is the first comprehensive study on the adsorption of water and butanol in silicalite-1 from vapor phase.

Comparative study on adsorption of crude oil and spent engine oil from seawater and freshwater using algal biomass.

Science.gov (United States)

Boleydei, Hamid; Mirghaffari, Nourollah; Farhadian, Omidvar

2018-05-15

Efficiency of a biosorbent prepared from the green macroalga Enteromorpha intestinalis biomass for decontamination of seawater and freshwater polluted by crude oil and engine spent oil was compared. The effect of different experimental conditions including contact time, pH, particle size, initial oil concentration, and biosorbent dose on the oil biosorption was studied in the batch method. The biosorbent was characterized by CHNOS, FTIR, and SEM analysis. The experimental data were well fitted to the pseudo-second-order kinetic model and the Langmuir adsorption isotherm model. Based on the obtained results, the adsorption of spent oil with higher viscosity was better than crude oil. The biosorption of oil hydrocarbons from seawater was more efficient than freshwater. The algal biomasses which are abundantly available could be effectively used as a low-cost and environmentally friendly adsorbent for remediation of oil spill in the marine environments or in the water and wastewater treatment.

Albumin adsorption on oxide thin films studied by spectroscopic ellipsometry

Energy Technology Data Exchange (ETDEWEB)

Silva-Bermudez, P., E-mail: suriel21@yahoo.com [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior s/n, C.U., 04510, Mexico D.F. (Mexico); Unidad de Posgrado, Facultad de Odontologia, Universidad Nacional Autonoma de Mexico, CU, 04510, Mexico D.F. (Mexico); Rodil, S.E.; Muhl, S. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior s/n, C.U., 04510, Mexico D.F. (Mexico)

2011-12-15

Thin films of tantalum, niobium, zirconium and titanium oxides were deposited by reactive magnetron sputtering and their wettability and surface energy, optical properties, roughness, chemical composition and microstructure were characterized using contact angle measurements, spectroscopic ellipsometry, profilometry, X-ray photoelectron spectroscopy and X-ray diffraction, respectively. The purpose of the work was to correlate the surface properties of the films to the Bovine Serum Albumin (BSA) adsorption, as a first step into the development of an initial in vitro test of the films biocompatibility, based on standardized protein adsorption essays. The films were immersed into BSA solutions with different protein concentrations and protein adsorption was monitored in situ by dynamic ellipsometry; the adsorption-rate was dependent on the solution concentration and the immersion time. The overall BSA adsorption was studied in situ using spectroscopic ellipsometry and it was found to be influenced by the wettability of the films; larger BSA adsorption occurred on the more hydrophobic surface, the ZrO{sub 2} film. On the Ta{sub 2}O{sub 5}, Nb{sub 2}O{sub 5} and TiO{sub 2} films, hydrophilic surfaces, the overall BSA adsorption increased with the surface roughness or the polar component of the surface energy.

Study of adsorption properties on lithium doped activated carbon materials

International Nuclear Information System (INIS)

Los, S.; Daclaux, L.; Letellier, M.; Azais, P.

2005-01-01

A volumetric method was applied to study an adsorption coefficient of hydrogen molecules in a gas phase on super activated carbon surface. The investigations were focused on getting the best possible materials for the energy storage. Several treatments on raw samples were used to improve adsorption properties. The biggest capacities were obtain after high temperature treatment at reduced atmosphere. The adsorption coefficient at 77 K and 2 MPa amounts to 3.158 wt.%. The charge transfer between lithium and carbon surface groups via the doping reaction enhanced the energy of adsorption. It was also found that is a gradual decrease in the adsorbed amount of H 2 molecules due to occupation active sites by lithium ions. (author)

Kinetics study of antimony adsorption on Si(1 1 1)

International Nuclear Information System (INIS)

Lapena, L.; Mueller, P.; Quentel, G.; Guesmi, H.; Treglia, G.

2003-01-01

In this paper, we use mass spectrometry (MS) and reflection high-energy electron (RHEED) to study the kinetics of adsorption of Sb on Si(1 1 1) surface and its relation to the corresponding surface structure. At high temperature (T>800 deg. C) all the impinging Sb 4 molecules completely dissociate at the silicon surface and a 2D gas of Sb monomers reversibly adsorbs on the (1x1) surface. At low temperature (T 4 molecules act as precursors and can be partially reflected or desorbed while a 2D stable layer of Sb monomers irreversibly adsorbs. The surface continuously shifts from a blurred (7x7) surface to a (1x1) structure near completion of the 2D layer. In the intermediate range (600 deg. C< T<800 deg. C) provided that the coverage is large enough (θ ∼ 2/3) the condensation of the 2D gas leads to a 2D (5√3 x 5√3) reconstruction. We show that introducing the formation of a condensed phase in a kinetics model allows us to reproduce our experimental data. Finally, we determine the adsorption geometry from ab initio calculations: Sb is adsorbed on top positions, somewhat passivating the Si surface dangling bonds

Resorcinol adsorption from aqueous solution on activated carbon: Relation adsorption isotherm and immersion enthalpy

International Nuclear Information System (INIS)

Blanco, Diago A; Giraldo, Liliana; Moreno, Juan C.

2008-01-01

The resorcinol adsorption on a modified activated carbon, obtained from an activated commercial carbon Carbochem T M - PS30, CAG, modified by means of chemical treatment with HNO 3 7M oxidized activated carbon (CAO) and heat treatment under H 2 flow, reduced activated carbon (CAR) are studied. The influence of solution pH, the reduction and oxidation of the activated surface carbons in resorcinol aqueous solutions is determined. The interaction solid solution is characterized by adsorption isotherms analysis at 298 K and at pHs of 7.9 and 11 in order to evaluate the system on and below the value of resorcinol pKa. The adsorption capacity of carbons increases with diminishing solution pH. The amount retained increases in the reduced carbon at maximum adsorption pH and diminishes in the oxidized carbon. the experimental results of the adsorption isotherms are adjusted to the Freundlich and Langmuir models, obtaining values for the Q m ax parameter Langmuir model in the CAG of 179, 156 and 44 mgg - 1 For pH values of 7,9 and 11 respectively. In this case of modified carbons values of 233, 179 and 164 mgg - 1 Are obtained for CAR, CAG and CAO to pH 7 respectively, as general tendency the resorcinol adsorption increases in the following order CAR > CAG > CAO. Similar conclusions from immersion enthalpies are obtained, their values increase with the amount of solute retained. In the case of the CAG, immersion enthalpies between 25.8 to 40.9 Jg - 1, are obtained for resorcinol aqueous solutions in a range from 20 to 1500 mgL - 1

Removal of cobalt from lubricant oil by the use of bentonite: equilibrium, kinetic and adsorption preliminary studies

Energy Technology Data Exchange (ETDEWEB)

Cuccia, Valeria; Seles, Sandro R.N.; Ladeira, Ana Cláudia Queiroz, E-mail: vc@cdtn.br, E-mail: seless@cdtn.br, E-mail: acql@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-11-01

Radionuclides may contaminate lubricant oils in nuclear power plants. In Brazil, this kind of waste has been stored in the generator's facilities, awaiting treatment alternatives. This work intends to investigate a process to treat it for final deposition, using bentonite as sorbent material. This process will result in decontaminated oil, free from radiological control, and radioactive loaded sorbent, with considerable volume reduction of the radioactive waste. The study focuses in cobalt removal from a simulated oil waste (non-active). The production of the simulated waste is described. Bentonite was used for equilibrium time determination, kinetic and adsorption studies. Cobalt adsorption equilibrium was rapidly attained after 30 minutes. The data was used for modelling the system's kinetic, applying the pseudo first and pseudo second order equation models. Experimental data fitted to pseudo second order model, supporting the assumption that the adsorption is due to chemisorption. Batch sorption tests were conducted and the results fitted to Langmuir and Freundlich sorption models. Both isotherm models chosen for this work did not fit to the experimental data. Thus, these are preliminary results and the studies must be repeated to evaluate data variability and better statistical inference. Other isotherm models must be evaluated to choose the best fitted one and describe the sorption of cobalt on bentonite in oil matrix. Even though, bentonite has considerable potential as sorbent for the removal of cobalt from lubricant oil. Finally, the results might be extended to other kinds of radioactive oils and radioactive organic wastes. (author)

Adsorption of ions by colloids in electrolyte solutions

International Nuclear Information System (INIS)

Kallay, N.

1977-01-01

The adsorption isotherm for ionic adsorption by colloid particles was evaluated. The adsorption process was treated as the reaction between colloid particles and ions. The colloid particle has been here considered as a reaction entity. The possibility of the surface potential determination was presented. The analyses of the experimental data showed, that (at electrolyte concentration higher than the critical coagulation one) the surface potential reaches its zero value

Modeling adsorption of binary and ternary mixtures on microporous media

DEFF Research Database (Denmark)

Monsalvo, Matias Alfonso; Shapiro, Alexander

2007-01-01

it possible using the same equation of state to describe the thermodynamic properties of the segregated and the bulk phases. For comparison, we also used the ideal adsorbed solution theory (IAST) to describe adsorption equilibria. The main advantage of these two models is their capabilities to predict......The goal of this work is to analyze the adsorption of binary and ternary mixtures on the basis of the multicomponent potential theory of adsorption (MPTA). In the MPTA, the adsorbate is considered as a segregated mixture in the external potential field emitted by the solid adsorbent. This makes...... multicomponent adsorption equilibria on the basis of single-component adsorption data. We compare the MPTA and IAST models to a large set of experimental data, obtaining reasonable good agreement with experimental data and high degree of predictability. Some limitations of both models are also discussed....

Computational and variable-temperature infrared spectroscopic studies on carbon monoxide adsorption on zeolite Ca-A.

Science.gov (United States)

Pulido, Angeles; Nachtigall, Petr; Rodríguez Delgado, Montserrat; Otero Areán, Carlos

2009-05-11

Carbon monoxide adsorption on LTA (Linde type 5A) zeolite Ca-A is studied by using a combination of variable-temperature infrared spectroscopy and computational methods involving periodic density functional calculations and the correlation between stretching frequency and bond length of adsorbed CO species (nu(CO)/r(CO) correlation). Based on the agreement between calculated and experimental results, the main adsorption species can be identified as bridged Ca(2+)...CO...Ca(2+) complexes formed on dual-cation sites constituted by a pair of nearby Ca(2+) cations. Two types of such species can be formed: One of them has the two Ca(2+) ions located on six-membered rings of the zeolite framework and is characterized by a C-O stretching frequency in the range of 2174-2179 cm(-1) and an adsorption enthalpy of -31 to -33 kJ mol(-1), whereas the other bridged CO species is formed between a Ca(2+) ion located on an eight-membered ring and another one on a nearby six-membered ring and is characterized by nu(CO) in the range 2183-2188 cm(-1) and an adsorption enthalpy of -46 to -50 kJ mol(-1). Ca(2+)...CO monocarbonyl complexes are also identified, and at a relatively high CO equilibrium pressure, dicarbonyl species can also be formed.

Equilibrium, kinetic and thermodynamic studies of adsorption of Pb(II) from aqueous solution onto Turkish kaolinite clay

International Nuclear Information System (INIS)

Sari, Ahmet; Tuzen, Mustafa; Citak, Demirhan; Soylak, Mustafa

2007-01-01

The adsorption of Pb(II) onto Turkish (Bandirma region) kaolinite clay was examined in aqueous solution with respect to the pH, adsorbent dosage, contact time, and temperature. The linear Langmuir and Freundlich models were applied to describe equilibrium isotherms and both models fitted well. The monolayer adsorption capacity was found as 31.75 mg/g at pH 5 and 20 deg. C. Dubinin-Radushkevich (D-R) isotherm model was also applied to the equilibrium data. The mean free energy of adsorption (13.78 kJ/mol) indicated that the adsorption of Pb(II) onto kaolinite clay may be carried out via chemical ion-exchange mechanism. Thermodynamic parameters, free energy (ΔG o ), enthalpy (ΔH o ) and entropy (ΔS o ) of adsorption were also calculated. These parameters showed that the adsorption of Pb(II) onto kaolinite clay was feasible, spontaneous and exothermic process in nature. Furthermore, the Lagergren-first-order, pseudo-second-order and the intraparticle diffusion models were used to describe the kinetic data. The experimental data fitted well the pseudo-second-order kinetics

Adsorption and desorption study of 14C-Chloropyrifos in two Malaysian agricultural soils

International Nuclear Information System (INIS)

Halimah Muhammad; Nashriyah Mat; Tan Yew Ai; Ismail, B.S.

2004-01-01

The adsorption equilibrium time and effects of pH and concentration of 14 C-labeled chloropyrifos 0,0-diethyl 0-(3, 5, 6 tricloro-2-pyridyl)-phosphorothiote in soil were investigated. Two types of Malaysian soil under oil palm were used in this study; namely clay loam and clay soil obtained from the Sungai Sedu and Kuala Lumpur International Airport (KLIA) Estates, respectively. Equilibrium studies of chloropyrifos between the agricultural soil and the pesticide solution were conducted. Adsorption equilibrium time was achieved within 6 and 24 hours for clay loam and clay soil, respectively. It was found that chloropyrifos adsorbed by the soil samples was characterized by an initial rapid adsorption after which adsorption remained approximately constant. The percentage of 14 C-labeled chloropyrifos adsorption on soil was found to be higher in clay loam than in clay soils. Results of the study demonstrated that pH affected the adsorption of chloropyrifos on both clay loam and clay soils. The adsorption of chloropyrifos on both types of soil was higher at low pH with the adsorption reduced as the pH increased. Results also suggest that chloropyrifos sorption by soil is concentration dependent. (Author)

Adsorption Study on Moringa Oleifera Seeds and Musa Cavendish as Natural Water Purification Agents for Removal of Lead, Nickel and Cadmium from Drinking Water

Science.gov (United States)

Aziz, N. A. A.; Jayasuriya, N.; Fan, L.

2016-07-01

The effectiveness of plant based materials Moringa oleifera (Moringa) seeds and Musa cavendish (banana peel) for removing heavy metals namely lead (Pb), nickel (Ni) and cadmium (Cd) from contaminated groundwater was studied. Tests were carried out with individual and combined biomass at neutral pH condition on synthetic groundwater samples. The optimum biomass doses were determined as 200 mg/L for single biomass and 400 mg/L (in the ratio of 200 mg/L: 200 mg/L) for combined biomasses and used for adsorption isotherm studies with contact time of 30 minutes. Results showed that combined biomasses was able to met the Pb, Ni and Cd WHO standards from higher Pb, Ni and Cd initial concentrations which were up to 40 µg/L, 50 µg/L 9 µg/L, respectively compared to individual biomass of Moringa seed and banana peel. Moringa seeds exhibited the highest removal of Pb (81%) while the combined biomasses was most effective in removing Ni (74%) and Cd (97%) over wider their initial concentration ranges. The experimental data were linearized with Langmuir and Freundlich adsorption isotherm models. Freundlich model described the Pb adsorption better than the Langmuir model for all the tested biomasses. However, the Langmuir model fit better with the experimental data of Ni adsorption by Moringa seeds. Both models showed negligible differences in the coefficient of determination (R2) when applied for Ni and Cd adsorption on banana peel and combined biomasses, suggesting that there were multiple layers on the biomass interacting with the metals. Chemisorption is suggested to be involved in Pb adsorption for all tested biomasses as the value of nF calculated was lower than one. This type of adsorption could explain the phenomenon of different behavior of Pb removal and the higher Pb adsorption capacity (represented by KF values) compared to Ni and Cd. The study demonstrates that Moringa seeds, banana peel and their combination have the potential to be used as a natural alternative

Adsorption of the herbicides diquat and difenzoquat on polyurethane foam: Kinetic, equilibrium and computational studies.

Science.gov (United States)

Vinhal, Jonas O; Nege, Kassem K; Lage, Mateus R; de M Carneiro, José Walkimar; Lima, Claudio F; Cassella, Ricardo J

2017-11-01

This work reports a study about the adsorption of the herbicides diquat and difenzoquat from aqueous medium employing polyurethane foam (PUF) as the adsorbent and sodium dodecylsulfate (SDS) as the counter ion. The adsorption efficiency was shown to be dependent on the concentration of SDS in solution, since the formation of an ion-associate between cationic herbicides (diquat and difenzoquat) and anionic dodecylsulfate is a fundamental step of the process. A computational study was carried out to identify the possible structure of the ion-associates that are formed in solution. They are probably formed by three units of dodecylsulfate bound to one unit of diquat, and two units of dodecylsulfate bound to one unit of difenzoquat. The results obtained also showed that 95% of both herbicides present in 45mL of a solution containing 5.5mgL -1 could be retained by 300mg of PUF. The experimental data were well adjusted to the Freundlich isotherm (r 2 ≥ 0.95) and to the pseudo-second-order kinetic equation. Also, the application of Morris-Weber and Reichenberg equations indicated that an intraparticle diffusion process is active in the control of adsorption kinetics. Copyright © 2017 Elsevier Inc. All rights reserved.

Equilibrium, kinetic and thermodynamic studies on the adsorption of phenol onto graphene

Energy Technology Data Exchange (ETDEWEB)

Li, Yanhui, E-mail: liyanhui@tsinghua.org.cn [Laboratory of Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, College of Electromechanical Engineering, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Du, Qiuju; Liu, Tonghao; Sun, Jiankun; Jiao, Yuqin [Laboratory of Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, College of Electromechanical Engineering, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Xia, Yanzhi, E-mail: xiayzh@qdu.edu.cn [Laboratory of Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, College of Electromechanical Engineering, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Xia, Linhua; Wang, Zonghua [Laboratory of Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, College of Electromechanical Engineering, Qingdao University, 308 Ningxia Road, Qingdao 266071 (China); Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai [Key Laboratory for Advanced Manufacturing by Material Processing Technology, Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2012-08-15

Graphical abstract: The effect of temperature on phenol adsorbed by graphene shows that the equilibrium adsorption capacity of phenol increases with the increase in temperature from 285 to 333 K. Increasing adsorption capacities with temperature indicates that the adsorption of phenol is controlled by an endothermic reaction. Highlights: ► The graphene has high phenol adsorption capacity. ► The graphene has a high specific surface area of 305 m{sup 2}/g. ► The adsorption capacity is high at acidic pH range. ► The graphene has rapid phenol adsorption rate. ► Phenol adsorption is a spontaneous and endothermic process. -- Abstract: Graphene, a new member of carbon family, has been prepared, characterized and used as adsorbent to remove phenol from aqueous solution. The effect parameters including pH, dosage, contact time, and temperature on the adsorption properties of phenol onto graphene were investigated. The results showed that the maximum adsorption capacity can reach 28.26 mg/g at the conditions of initial phenol concentration of 50 mg/L, pH 6.3 and 285 K. Adsorption data were well described by both Freundlich and Langmuir models. The kinetic study illustrated that the adsorption of phenol onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of phenol onto graphene was endothermic and spontaneous.

Equilibrium, kinetic and thermodynamic studies on the adsorption of phenol onto graphene

International Nuclear Information System (INIS)

Li, Yanhui; Du, Qiuju; Liu, Tonghao; Sun, Jiankun; Jiao, Yuqin; Xia, Yanzhi; Xia, Linhua; Wang, Zonghua; Zhang, Wei; Wang, Kunlin; Zhu, Hongwei; Wu, Dehai

2012-01-01

Graphical abstract: The effect of temperature on phenol adsorbed by graphene shows that the equilibrium adsorption capacity of phenol increases with the increase in temperature from 285 to 333 K. Increasing adsorption capacities with temperature indicates that the adsorption of phenol is controlled by an endothermic reaction. Highlights: ► The graphene has high phenol adsorption capacity. ► The graphene has a high specific surface area of 305 m 2 /g. ► The adsorption capacity is high at acidic pH range. ► The graphene has rapid phenol adsorption rate. ► Phenol adsorption is a spontaneous and endothermic process. -- Abstract: Graphene, a new member of carbon family, has been prepared, characterized and used as adsorbent to remove phenol from aqueous solution. The effect parameters including pH, dosage, contact time, and temperature on the adsorption properties of phenol onto graphene were investigated. The results showed that the maximum adsorption capacity can reach 28.26 mg/g at the conditions of initial phenol concentration of 50 mg/L, pH 6.3 and 285 K. Adsorption data were well described by both Freundlich and Langmuir models. The kinetic study illustrated that the adsorption of phenol onto graphene fit the pseudo second-order model. The thermodynamic parameters indicated that the adsorption of phenol onto graphene was endothermic and spontaneous.

Evaluation of dyes adsorption properties of TiO2-alginate biohybrid material

International Nuclear Information System (INIS)

Barrón Zambrano, J A; Ávila Ortega, A; Muñoz Rodríguez, D; Carrera Figueiras, C; Sánchez Morales, G

2013-01-01

In this study a TiO 2 -alginate biohybrid material was obtained by the sol gel method and its adsorption properties were compared to those of its precursors using eosin B (anionic) as model dye. The results showed that the TiO 2 and biohybrid have a greater affinity for eosine B than alginate. The maximum adsorption capacity for the eosin B was obtained at pH = 10. Kinetic studies showed that the biohybrid has greater rate and adsorption capacity than its precursors. Kinetic data were fitted to a pseudo-second order kinetic model. The experimental isotherms were fitted to the Langmuir model.

Adsorption isotherm special study. Final report

International Nuclear Information System (INIS)

1993-05-01

The study was designed to identify methods to determine adsorption applicable to Uranium Mill Tailings Remedial Action (UMTRA) Project sites, and to determine how changes in aquifer conditions affect metal adsorption, resulting retardation factors, and estimated contaminant migration rates. EPA and ASTM procedures were used to estimate sediment sorption of U, As, and Mo under varying groundwater geochemical conditions. Aquifer matrix materials from three distinct locations at the DOE UMTRA Project site in Rifle, CO, were used as the adsorbents under different pH conditions; these conditions stimulated geochemical environments under the tailings, near the tailings, and downgradient from the tailings. Grain size, total surface area, bulk and clay mineralogy, and petrography of the sediments were characterized. U and Mo yielded linear isotherms, while As had nonlinear ones. U and Mo were adsorbed strongly on sediments acidified to levels similar to tailings leachate. Changes in pH had much less effect on As adsorption. Mo was adsorbed very little at pH 7-7.3, U was weakly sorbed, and As was moderately sorbed. Velocities were estimated for metal transport at different pHs. Results show that the aquifer materials must be characterized to estimate metal transport velocities in aquifers and to develop groundwater restoration strategies for the UMTRA project

Effects of chemical functional groups on elemental mercury adsorption on carbonaceous surfaces

Energy Technology Data Exchange (ETDEWEB)

Liu Jing, E-mail: liujing27@mail.hust.edu.cn [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan 430074 (China); Cheney, Marcos A. [Department of Natural Sciences, University of Maryland Eastern Shore, Princess Anne, MD 21853 (United States); Wu Fan; Li Meng [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan 430074 (China)

2011-02-15

A systematic theoretical study using density functional theory is performed to provide molecular-level understanding of the effects of chemical functional groups on mercury adsorption on carbonaceous surfaces. The zigzag and armchair edges were used in modeling the carbonaceous surfaces to simulate different adsorption sites. The edge atoms on the upper side of the models are unsaturated to simulate active sites. All calculations (optimizations, energies, and frequencies) were made at B3PW91 density functional theory level, using RCEP60VDZ basis set for mercury and 6-31G(d) pople basis set for other atoms. The results indicate that the embedding of halogen atom can increase the activity of its neighboring site which in turn increases the adsorption capacity of the carbonaceous surface for Hg{sup 0}. The adsorption belongs to chemisorptions, which is in good agreement with the experimental results. For the effects of oxygen functional groups, lactone, carbonyl and semiquinone favor Hg{sup 0} adsorption because they increase the neighboring site's activity for mercury adsorption. On the contrary, phenol and carboxyl functional groups show a physisorption of Hg{sup 0}, and reduce Hg capture. This result can explain the seemingly conflicting experimental results reported in the literature concerning the influence of oxygen functional groups on mercury adsorption on carbonaceous surface.

Study on the adsorption-desorption characteristics of 14C-pirimicarb in soils

International Nuclear Information System (INIS)

Guo Jiangfeng; Sun Jinhe; Li Xingming

1995-01-01

14 C-pirimicarb was used to study its adsorption-desorption behavior in 8 kinds of soils. The results indicated that there were significant differences in its adsorption with different kinds of soil. The lowest adsorption percentage was only 13.16% and the highest one was 87.75%. The amount of adsorption in the same kind of soil increased with the concentration of pesticide, but concentration had little influence on the adsorption within the certain range of concentrations. Multiple linear regression equation was developed for prediction of adsorption and determination of the relative importance of the soil parameters. It was significant that the key factors, soil pH and clay content were negatively and positively correlated with the adsorption respectively. The adsorption equilibrium of pirimicarb in soils could be well described by both the Freundlich isotherm and the Langmuir isotherm. The adsorbed 14 C-pirimicarb could disrobe from soil and its desorption was also influenced by soil properties described by multiple linear regression equation

Performance evaluation of Fe (III) adsorption onto brewers' spent grain

African Journals Online (AJOL)

Thereafter, batch adsorption technique was employed to evaluate the effects of adsorption variables such as pH, initial metal ion concentration, adsorbent dosage and contact time on the sorption efficiency of BSG. The maximum adsorption time was fixed at 120minutes with a stirring speed of 100rpm. Experimental data ...

Ultra Low Concentration Adsorption Equilibria

National Research Council Canada - National Science Library

Mahle, John J; Buettner, Leonard C; LeVan, M. D; Schindler, Bryan J

2006-01-01

.... Specifically this work focuses on novel experimental and modeling methods to characterize and predict at ultra-low chemical vapor concentrations the protection afforded by adsorption-based vapor filtration systems...

SeO{sub 2} adsorption on CaO surface: DFT study on the adsorption of a single SeO{sub 2} molecule

Energy Technology Data Exchange (ETDEWEB)

Fan, Yaming; Zhuo, Yuqun; Lou, Yu; Zhu, Zhenwu [Key Laboratory for Thermal Science and Power Engineering of Ministry of Education, Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China); Li, Liangliang [Key Laboratory of Advanced Materials, Department of Material Science and Engineering, Tsinghua University, Beijing 100084 (China)

2017-08-15

Highlights: • Adsorption mechanisms of SeO{sub 2} on CaO surface under O{sub 2} were firstly studied by DFT. • The adsorption energies, bond length and electron density maps were calculated. • The electronic structure changes upon adsorption were studied. - Abstract: Selenium is a hazardous element in coal. During coal combustion, most of the selenium will convert to SeO{sub 2} in the flue gas. Ca-based adsorbents, especially CaO, have been considered as a potential sorbent to adsorb SeO{sub 2} due to its low cost. In this paper, the adsorption mechanisms of single SeO{sub 2} on CaO surface were investigated by density functional theory (DFT) calculation. Both the physisorption and chemisorption structures were determined. It has been identified that the adsorption of SeO{sub 2} on CaO surface is primarily chemisorption, while physisorption takes effects at the initial stage of the process. Under O{sub 2} atmosphere, selenate is hard to form. Most of the adsorption products are selenite. Additionally, the electron density maps were obtained to reveal the surface active sites. The partial density of states (PDOS) was calculated for analyzing the electronic structural change of SeO{sub 2} and CaO surface during adsorption. The results provide fundamental information of the adsorption process, which could be meaningful for the development of new absorbents.

An adsorption of carbon dioxide on activated carbon controlled by temperature swing adsorption

Science.gov (United States)

Tomas, Korinek; Karel, Frana

2017-09-01

This work deals with a method of capturing carbon dioxide (CO2) in indoor air. Temperature Swing Adsorption (TSA) on solid adsorbent was chosen for CO2 capture. Commercial activated carbon (AC) in form of extruded pellets was used as a solid adsorbent. There was constructed a simple device to testing effectiveness of CO2 capture in a fixed bed with AC. The TSA cycle was also simulated using the open-source software OpenFOAM. There was a good agreement between results obtained from numerical simulations and experimental data for adsorption process.

Characteristics of Alcian-blue Dye Adsorption of Natural Biofilm Matrix

Science.gov (United States)

Kurniawan, A.; Yamamoto, T.; Sukandar; Guntur

2018-01-01

In this study, natural biofilm matrices formed on stones have been used for the adsorption of Alcian blue dye. Alcian blue is a member of polyvalent basic dyes that largely used from laboratory until industrial dying purposes. The adsorption of the dye onto the biofilm matrix has been carried out at different experimental conditions such as adsorption isotherm and kinetic of adsorption. The electric charge properties of biofilm matrix and its changes related to the adsorption of Alcian blue have been also investigated. Moreover, the results of Alcian blue adsorption to the biofilm were compared to those onto the acidic and neutral resin. The kinetics of adsorption result showed that the adsorption of the Alcian blue dye reached to a maximum adsorption amount within 60 minutes. The adsorption amount of Alcian blue to biofilm increased monotonously, and the maximum adsorption amount was greater compared to the resins. On the contrary, Alcian blue did not attach to the neutral resin having no electric charge. It seems that Alcian blue attached to the acidic resins due to electrostatic attractive force, and the same seems to be the case for adsorption of Alcian blue to biofilm. The adsorption of Alcian blue to the biofilm and acidic resins fitted to Langmuir type indicates that the binding of Alcian blue to the biofilm and acidic resins occurred in a monolayer like form. The maximum adsorption amount of Alcian blue on the biofilm (0.24 mmol/dry-g) was greater than those of acidic resin (0.025 mmol/dry-g). This indicates that the biofilm has many more sites for Alcian blue attachment than acidic resins. According to the result of this study, the biofilm matrix can be a good adsorbent for dye such as Alcian blue or other dyes that causing hazards in nature.

Kinetic and equilibrium studies of Pb(II and Cd(II adsorption on African wild mango (Irvingia gabonensis shell

Directory of Open Access Journals (Sweden)

F. A. Adekola

2016-08-01

Full Text Available The adsorption behavior of NaOH-activated African wild mango (Irvingia gabonensis shell with respect to Pb2+ and Cd2+ has been studied in order to consider its application to purify metal finishing waste water. The optimum conditions of adsorption were determined by investigating the initial metal ions concentration, contact time, adsorbent dose, pH value of aqueous solution and temperature. The extent of adsorption of metal ions was investigated by batch method using metal concentrations in solution ranging from 5-200 mg/L. The adsorption efficiencies were found to be pH dependent, with maximum metals uptake recorded at pH of 5. The equilibrium adsorption capacity for lead and cadmium ions were obtained from Freundlich, Langmuir, Temkin and DRK isotherms and the experimental data were found to fit best the Langmuir isotherm with values of 21.28 and 40.00 mg/g for Cd(II and Pb(II ions, respectively. The Pseudo-second order kinetics model had the best fitting for lead and cadmium adsorption kinetic data. The thermodynamic investigation showed that the adsorption processes of both metals are exothermic. An optimum concentration of 0.05 M HCl was found to be adequate for the regeneration of the spent adsorbent with recovery values of 78% and 71% for Pb2+ and Cd2+ respectively from the spent adsorbent. The results revealed that lead and cadmium are considerably adsorbed on the adsorbent and could be an economic method for the removal of these metals from aqueous solutions.

Combined quantum chemistry and Monte Carlo simulation of competitive adsorption of O{sub 2} and OH on Pt surfaces

Energy Technology Data Exchange (ETDEWEB)

Li, Rui, E-mail: ruililcu@gmail.com [Department of Chemistry, Liaocheng University, Liaocheng 252059 (China); Li, Haibo; Xu, Shuling [Department of Chemistry, Liaocheng University, Liaocheng 252059 (China); Liu, Jifeng, E-mail: liujifeng111@gmail.com [Key Laboratory of Food Nutrition and Safety, Ministry of Education of China, Tianjin University of Science and Technology, Tianjin 300457 (China)

2017-07-15

Highlights: • Competitive adsorption of O{sub 2} and OH on different Pt surfaces was theoretically studied. • The adsorption energies of O{sub 2} and OH depend on the Pt surfaces and the adsorption sites. • The order of O{sub 2} adsorption efficiency was characterized. - Abstract: To obtain a microscopic explanation on the difference of oxygen reduction reaction activity on different Pt low index surfaces, we simulated competitive adsorptions of O{sub 2} and OH on four Pt low index surfaces. Firstly, all possible chemical adsorption configurations of the O{sub 2} and OH molecules on the three surfaces were acquired through density functional theory. The distribution of these configurations on the different surfaces was collected from Monte Carlo simulations. Our results demonstrated that the adsorption energy order of O{sub 2} on different surfaces was (110)(1 × 2) > (110) > (100) > (111) and that the adsorption energy order of the OH molecules on Pt surfaces was the same. Considering the competitive adsorption of O{sub 2} and OH on Pt surfaces, the final O{sub 2} adsorption efficiencies order of three surfaces was (111) > (110) > (100) > (110)(1 × 2), which was consistent with the experimental activities of oxygen reduction. Our study provided theoretical references for previous experimental studies and had important significance for the understanding of oxygen adsorption on Pt surfaces.

Effect of surface acidic oxides of activated carbon on adsorption of ammonia.

Science.gov (United States)

Huang, Chen-Chia; Li, Hong-Song; Chen, Chien-Hung

2008-11-30

The influence of surface acidity of activated carbon (AC) was experimentally studied on adsorption of ammonia (NH(3)). Coconut shell-based AC was modified by various acids at different concentrations. There were five different acids employed to modified AC, which included nitric acid, sulfuric acid, hydrochloric acid, phosphoric acid, and acetic acid. Acidic functional groups on the surface of ACs were determined by a Fourier transform infrared spectrograph (FTIR) and by the Boehm titration method. Specific surface area and pore volume of the ACs were measured by a nitrogen adsorption apparatus. Adsorption amounts of NH(3) onto the ACs were measured by a dynamic adsorption system at room temperature according to the principle of the ASTM standard test method. The concentration of NH(3) in the effluent stream was monitored by a gas-detecting tube technique. Experimental results showed that adsorption amounts of NH(3) on the modified ACs were all enhanced. The ammonia adsorption amounts on various activated carbons modified by different acids are in the following order: nitric acid>sulfuric acid>acetic acid approximately phosphoric acid>hydrochloric acid. It is worth to note that the breakthrough capacity of NH(3) is linearly proportional to the amount of acidic functional groups of the ACs.

Adsorption of radioactive I2 gas onto atmospheric aerosol

International Nuclear Information System (INIS)

Noguchi, Hiroshi; Murata, Mikio; Suzuki, Katsumi.

1990-01-01

Laboratory scale experiments on the adsorption of radioactive elemental iodine (I 2 ) gas onto atmospheric aerosol showed that the adsorption reached an equilibrium state in about twelve minutes at high initial I 2 concentrations. The proportion of iodine which was adsorbed on the aerosol gradually decreased with increading initial I 2 concentration ranging over 10 -13 to 10 -9 g/cm 3 at a reaction time of 31 min but was almost constant at a reaction time of 2 min. A fraction of iodine desorbed from particulate iodine as mainly I 2 gas. An adsorption isotherm of atmospheric aerosol for I 2 gas was estimated from the experimental data of long reaction time and high I 2 concentrations. Using this adsorption isotherm, a theoretical equation, which was similar to our previous equation, was derived to explain the experimental results. A geometric mean and standard deviation of sticking probability in the equation were estimated to be 1.2 x 10 -2 and 2.7, respectively. Almost all experimental data were within ranges of calculated results considering the geometric standard deviation of sticking probability. (author)

Kinetics of hydrogen adsorption on MgH{sub 2}/CNT composite

Energy Technology Data Exchange (ETDEWEB)

Rather, Sami ullah, E-mail: rathersami@gmail.com; Taimoor, Aqeel Ahmad; Muhammad, Ayyaz; Alhamed, Yahia Abobakor; Zaman, Sharif Fakhruz; Ali, Arshid Mahmood

2016-05-15

Highlights: • Hydrogen adsorption comparisons of commercial, milled, and MgH{sub 2} composite. • Hydrogen adsorption capacity and kinetics improves tremendously by CNT embedding. • Unsteady state modeling and simulation of adsorption kinetics. - Abstract: Magnesium hydride (MgH{sub 2})–carbon nanotubes (CNT) composite has been prepared by high-energy ball milling method and their experimental and kinetic hydrogen adsorption studies was assessed. Hydrogen adsorption studies were performed by Sievert’s volumetric apparatus and kinetic evaluation was conducted by surface chemistry and Langmuir–Hinshelwood–Hougen–Watson (LHHW) type mode. Powder X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) were performed. Hydrogen adsorption capacity of commercial MgH{sub 2}, milled MgH{sub 2}, and MgH{sub 2}/CNT composite are found to be 0.04, 0.057, and 0.059 g (H{sub 2})/g (MgH{sub 2}) at 673 K and hydrogen pressure of 4.6 MPa. Addition of 5 wt% of CNTs to MgH{sub 2} proved to be very critical to enhance hydrogen adsorption as well as to improve its kinetics. It was observed that hydrogen adsorption is not in quasi-state equilibrium and is modeled using kinetic rate laws.

Magnetic vinylphenyl boronic acid microparticles for Cr(VI) adsorption: Kinetic, isotherm and thermodynamic studies

International Nuclear Information System (INIS)

Kara, Ali; Demirbel, Emel; Tekin, Nalan; Osman, Bilgen; Beşirli, Necati

2015-01-01

Highlights: • Cr(VI) can oxidize biological molecules and be one of the most harmful substance. • Magnetic seperation techniques are used on different applications in many fields. • Magnetic systems can be used for rapid and selective removal as a magnetic processor. • We investigate properties of both new material and other magnetic adsorbents reported in the literatures on the adsorption of Cr(VI) ions. • No researchments were reported on adsorption of Cr(VI) with magnetic vinylphenyl boronic acid microparticles. - Abstract: Magnetic vinylphenyl boronic acid microparticles, poly(ethylene glycol dimethacrylate(EG)–vinylphenyl boronic acid(VPBA)) [m-poly(EG–VPBA)], produced by suspension polymerization and characterized, was found to be an efficient solid polymer for Cr(VI) adsorption. The m-poly(EG–VPBA) microparticles were prepared by copolymerizing of ethylene glycol dimethylacrylate (EG) with 4-vinyl phenyl boronic acid (VPBA). The m-poly(EG–VPBA) microparticles were characterized by N 2 adsorption/desorption isotherms, electron spin resonance (ESR), X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA), elemental analysis, scanning electron microscope (SEM) and swelling studies. The m-poly(EG–VPBA) microparticles were used at adsorbent/Cr(VI) ion ratios. The influence of pH, Cr(VI) initial concentration, temperature of the removal process was investigated. The maximum removal of Cr(VI) was observed at pH 2. Langmuir isotherm and Dubinin–Radushkvich isotherm were found to better fit the experiment data rather than Fruendlich isotherm. The kinetics of the adsorption process of Cr(VI) on the m-poly(EG–VPBA) microparticles were investigated using the pseudo first-order, pseudo-second-order, Ritch-second-order and intraparticle diffusion models, results showed that the pseudo-second order equation model provided the best correlation with the experimental results. The thermodynamic

A comparative study of the adsorption of uranium on commercial and natural (Cypriot) sea sand samples

International Nuclear Information System (INIS)

Maria Efstathiou; Ioannis Pashalidis

2013-01-01

The adsorption of hexavalent uranium on two different types of sea sand [e.g. a local, Cypriot (N S S) and a commercially available marine sediment (C S S)] has been investigated as a function of pH, initial metal concentration, ionic strength and contact time under normal atmospheric conditions. Before carrying out the adsorption experiments, the sea sand samples have been characterized by XRD, XRF, N 2 -adsorption, acid/base titrations and FTIR spectroscopy. Sample characterization showed clearly that the two sea sand types differ significantly in their composition, particularly in their calcite and FeOOH content. According to experimental data obtained from acid/base titrations and adsorption batch experiments sea sand composition affects the acid/base and the adsorption properties of the adsorbents. The extraordinary high affinity of N S S for hexavalent uranium in the alkaline pH region can be attributed to the formation of mixed U(VI)-carbonato surface species on the FeOOH crystal phases present in N S S, which effectively compete the formation of U(VI)-carbonato complexes in solution. On the other hand, data obtained by adsorption experiments carried out in solution of different ionic strengths don't differ significantly from one another indicating the formation of inner-sphere complexes. Finally, the adsorption on sea sands is a relatively fast two-step process. (author)

Adsorption of Cr(III) from Aqueous Solution using Borax Sludge.

Science.gov (United States)

Senberber, Fatma Tugce; Yildirim, Meral; Mermer, Nevin Karamahmut; Derun, Emek Moroydor

2017-09-01

Borax sludge is the waste produced by a trommel sieve in the borax production process and is used as an adsorbent for Cr(III) removal. The effects of various parameters, including pH, initial Cr(III) concentration and contact time were investigated for batch adsorption of Cr(III). The experimental results obtained were applied to different adsorption isotherms and kinetic models. The results indicated that the Temkin isotherm (R2 = 0.9749) was most suitable to explain the adsorption characteristics of borax sludge, and the removal of Cr(III) was achieved by a physisorption process. The overall kinetic data fitted the pseudo-second order rate model (R2 = 0.9990). According to thermodynamic studies, which were carried out at different temperatures, changes in enthalpy (ΔH) and entropy (ΔS) values for Cr(III) adsorption by borax sludge were determined to be 69.395 kJ/mol and 0.276 kJ/mol K, respectively. The study implied that borax sludge could be used as an alternative adsorbent in the adsorption of Cr(III) from aqueous solutions.

Study of carbon dioxide adsorption on a Cu-nitroprusside polymorph

International Nuclear Information System (INIS)

Roque-Malherbe, R.; Lozano, C.; Polanco, R.; Marquez, F.; Lugo, F.; Hernandez-Maldonado, A.; Primera-Pedrozo, J.N.

2011-01-01

A careful structural characterization was carried out to unequivocally determine the structure of the synthesized material. The TGA, DRIFTS and a Pawley fitting of the XRD powder profiles indicate that the hydrated and in situ dehydrated polymorph crystallizes in the orthorhombic space group Pnma. Meanwhile, the CO 2 isosteric heat of adsorption appears to be independent of loading with an average value of 30 kJ/mol. This translates to a physisorption type interaction, where the adsorption energy corresponding to wall and lateral interactions are mutually compensated to produce, an apparently, homogeneous adsorption energy. The somewhat high adsorption energy is probably due to the confinement of the CO 2 molecules in the nitroprusside pores. Statistical Physics and the Dubinin theory for pore volume filling allowed model the CO 2 equilibrium adsorption process in Cu-nitroprusside. A DRIFTS test for the adsorbed CO 2 displayed a peak at about 2338 cm -1 that was assigned to a contribution due to physical adsorption of the molecule. Another peak found at 2362 cm -1 evidenced that this molecule interacts with the Cu 2+ , which appears to act as an electron accepting Lewis acid site. The aim of the present paper is to report a Pnma stable Cu-nitroprusside polymorph obtained by the precipitation method that can adsorb carbon dioxide. -- Graphical abstract: The adsorption space of a very well characterized Cu-nitroprusside polymorph, applying carbon dioxide as probe molecule, was studied. Display Omitted Highlights: → Accurate information about the geometry of the adsorption space was provided. → Truthful data about the interactions within the adsorption space was presented. → The structure of the tested Cu-NP polymorph was established. → Was evidenced adsorbed CO 2 molecules in the form of weakly bonded adducts. → Is proposed that adsorbed molecules could change the Cu-NP magnetic properties.

Adsorption of Remazol Black B dye on Activated Carbon Felt

Directory of Open Access Journals (Sweden)

Donnaperna Lucio

2008-11-01

Full Text Available The adsorption of Remazol Black B (anionic dye on a microporous activated carbon felt is investigated from its aqueous solution. The surface chemistry of activated carbon is studied using X-ray microanalysis, "Boehm" titrations and pH of PZC measurements which indicates that the surface oxygenated groups are mainly acidic in nature. The kinetics of Remazol Black B adsorption is observed to be pH dependent and governed by the diffusion of the dye molecules. The experimental data can be explained by "intra-particle diffusion model". For Remazol Black B, the Khan model is best suited to simulate the adsorption isotherms.

REMOVAL OF AN ACID DYE FROM AQUEOUS SOLUTIONS BY ADSORPTION ON A COMMERCIAL GRANULAR ACTIVATED CARBON: EQUILIBRIUM, KINETIC AND THERMODYNAMIC STUDY

Directory of Open Access Journals (Sweden)

Marius Sebastian Secula

2011-12-01

Full Text Available The present paper approaches the study of the adsorption of an acid dye on a commercial granular activated carbon (GAC. Batch experiments were conducted to study the equilibrium isotherms and kinetics of Indigo Carmine on GAC. The kinetic data were analyzed using the Lagargren, Ho, Elovich, Weber-Morris and Bangham models in order to establish the most adequate model that describes this process, and to investigate the rate of IC adsorption. Equilibrium data were fitted to Langmuir and Freundlich isotherms. Langmuir isotherm equilibrium model and Ho kinetic model fitted best the experimental data.The effects of temperature (25 – 45 °C, initial concentration of dye (7.5 – 150 mg•L−1, GAC dose (0.02 – 1 g•L-1, particle size (2 – 7 mm in diameter, solution pH (3 – 11 on GAC adsorption capacity were established. The adsorption process is found to be favored by a neutral pH, high values of temperature and small particle sizes. The highest adsorption capacity (133.8 mg•g-1 of the GAC is obtained at 45 °C. The removal efficiency increases with GAC dose at relatively low initial concentrations of dye. Thermodynamic parameters such as standard enthalpy (H, standard entropy (S and standard free energy (G were evaluated. The adsorption of Indigo Carmine onto GAC is an endothermic process.

Synthetic Textile Red Dye Removal From Aqueous Solution by Adsorption onto Pomegranate Peel

Directory of Open Access Journals (Sweden)

Sundus Saleh Nehaba

2017-07-01

Full Text Available This study is conducted to evaluate the ability of using pomegranate peel as low cost material for adsorption one of synthetic textile dye (C.I.Direct Red 89 dye. The removal of dye from aqueous solution is done by using pomegranate peel with two forms, as raw pomegranate peel (RPP and activated carbon prepared from pomegranate peel(ACPP. Some operational factors like contact time, pH, adsorbent dosage , and temperature were investigated in experimental work. Also the thermodynamic parameters ΔH, ΔG, and ΔS were calculated, the result shows that the adsorption process of dye onto two forms of adsorbents was spontaneous and endothermic in nature. Finally, the adsorption isotherm of experimental data we refitted for the Langmuir, and Freundlich equations

Study of adsorption states for lubricant molecule using hard X-ray photoemission spectroscopy

International Nuclear Information System (INIS)

Ikenaga, E.; Kobata, M.; Kim, J.J.; Wakabayashi, A.; Nishino, Y.; Tamasaku, K.; Sakane, Y.; Ishikawa, T.; Komiya, S.; Kobayashi, K.

2007-01-01

The adsorption states for lubricant molecules have been investigated using hard X-ray (hν = 7.95 keV) photoemission spectroscopy (HX-PES). This method has the advantage for the organic molecules to be able to measure damage few. Being aware of the fact that P atoms exist only in cyclotriphosphazene base, we measured the take-off angle dependence of the P1s spectra. Each spectrum consists from two peaks, that is, substrate NiP peak and cyclotriphosphazene P peak. The cyclotriphosphazene P peak rapidly disappears with increasing take-off angle. We have also measured C1s spectra. Combining these experimental results, we have found that the adsorption state of cyclotriphosphazene end group is undergoing

Adsorption treatment of oxide chemical mechanical polishing wastewater from a semiconductor manufacturing plant by electrocoagulation

Energy Technology Data Exchange (ETDEWEB)

Chou, Wei-Lung, E-mail: wlchou@sunrise.hk.edu.tw [Department of Safety, Health and Environmental Engineering, Hungkuang University, No. 34, Chung-Chie Road, Sha-Lu, Taichung 433, Taiwan (China); Wang, Chih-Ta [Department of Safety Health and Environmental Engineering, Chung Hwa University of Medical Technology, Tainan Hsien 717, Taiwan (China); Chang, Wen-Chun; Chang, Shih-Yu [Department of Safety, Health and Environmental Engineering, Hungkuang University, No. 34, Chung-Chie Road, Sha-Lu, Taichung 433, Taiwan (China)

2010-08-15

In this study, metal hydroxides generated during electrocoagulation (EC) were used to remove the chemical oxygen demand (COD) of oxide chemical mechanical polishing (oxide-CMP) wastewater from a semiconductor manufacturing plant by EC. Adsorption studies were conducted in a batch system for various current densities and temperatures. The COD concentration in the oxide-CMP wastewater was effectively removed and decreased by more than 90%, resulting in a final wastewater COD concentration that was below the Taiwan discharge standard (100 mg L{sup -1}). Since the processed wastewater quality exceeded the direct discharge standard, the effluent could be considered for reuse. The adsorption kinetic studies showed that the EC process was best described using the pseudo-second-order kinetic model at the various current densities and temperatures. The experimental data were also tested against different adsorption isotherm models to describe the EC process. The Freundlich adsorption isotherm model predictions matched satisfactorily with the experimental observations. Thermodynamic parameters, including the Gibbs free energy, enthalpy, and entropy, indicated that the COD adsorption of oxide-CMP wastewater on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

Adsorption treatment of oxide chemical mechanical polishing wastewater from a semiconductor manufacturing plant by electrocoagulation

International Nuclear Information System (INIS)

Chou, Wei-Lung; Wang, Chih-Ta; Chang, Wen-Chun; Chang, Shih-Yu

2010-01-01

In this study, metal hydroxides generated during electrocoagulation (EC) were used to remove the chemical oxygen demand (COD) of oxide chemical mechanical polishing (oxide-CMP) wastewater from a semiconductor manufacturing plant by EC. Adsorption studies were conducted in a batch system for various current densities and temperatures. The COD concentration in the oxide-CMP wastewater was effectively removed and decreased by more than 90%, resulting in a final wastewater COD concentration that was below the Taiwan discharge standard (100 mg L -1 ). Since the processed wastewater quality exceeded the direct discharge standard, the effluent could be considered for reuse. The adsorption kinetic studies showed that the EC process was best described using the pseudo-second-order kinetic model at the various current densities and temperatures. The experimental data were also tested against different adsorption isotherm models to describe the EC process. The Freundlich adsorption isotherm model predictions matched satisfactorily with the experimental observations. Thermodynamic parameters, including the Gibbs free energy, enthalpy, and entropy, indicated that the COD adsorption of oxide-CMP wastewater on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

Adsorption treatment of oxide chemical mechanical polishing wastewater from a semiconductor manufacturing plant by electrocoagulation.

Science.gov (United States)

Chou, Wei-Lung; Wang, Chih-Ta; Chang, Wen-Chun; Chang, Shih-Yu

2010-08-15

In this study, metal hydroxides generated during electrocoagulation (EC) were used to remove the chemical oxygen demand (COD) of oxide chemical mechanical polishing (oxide-CMP) wastewater from a semiconductor manufacturing plant by EC. Adsorption studies were conducted in a batch system for various current densities and temperatures. The COD concentration in the oxide-CMP wastewater was effectively removed and decreased by more than 90%, resulting in a final wastewater COD concentration that was below the Taiwan discharge standard (100 mg L(-1)). Since the processed wastewater quality exceeded the direct discharge standard, the effluent could be considered for reuse. The adsorption kinetic studies showed that the EC process was best described using the pseudo-second-order kinetic model at the various current densities and temperatures. The experimental data were also tested against different adsorption isotherm models to describe the EC process. The Freundlich adsorption isotherm model predictions matched satisfactorily with the experimental observations. Thermodynamic parameters, including the Gibbs free energy, enthalpy, and entropy, indicated that the COD adsorption of oxide-CMP wastewater on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K. Copyright 2010 Elsevier B.V. All rights reserved.

A Study on adsorption of Li from aqueous solution using various adsorbents

Energy Technology Data Exchange (ETDEWEB)

Ryoo, Keon Sang [Dept. of Applied Chemistry, Andong National University, Andon (Korea, Republic of); Kim, Dae Ik [School of Electrical, Electronic Communication, and Computer Engineering, Chonnam National University, Yeosu (Korea, Republic of)

2015-04-15

The aim of the present study is to explore the possibility of utilizing fly ash, loess and activated charcoal for the adsorption of Li in aqueous solution. Batch adsorption experiments were performed to evaluate the influences of various factors like initial concentration, contact time, and temperature. The adsorption data showed that fly ash and activated charcoal are not effective for the adsorption of Li. On the contrary, loess showed much higher adsorption capacity for Li. The adsorption of Li on loess was highly concentration dependent. It was found that the adsorption capacity of loess is favored at a lower Li concentration. At equilibrium, approximately 95% of adsorption was achieved by loess. The equilibrium data were fitted well to the Freundlich isotherm model. The pseudo-second-order kinetic model appeared to be the better-fitting model because it has higher R 2 compared to the pseudo-first-order kinetic models. The thermodynamic parameters such as free energy ΔG, the enthalpy ΔH, and the entropy ΔS were calculated.

Experimental and theoretical study of CO adsorption on the surface of single phase hexagonally plate ZnO

Energy Technology Data Exchange (ETDEWEB)

Akbari, Amin; Firooz, Azam Anaraki [Chemistry Department, Faculty of Sciences, Shahid Rajaee Teacher Training University, PO Box 16785-163, Tehran (Iran, Islamic Republic of); Beheshtian, Javad, E-mail: j.beheshtian@srttu.edu [Chemistry Department, Faculty of Sciences, Shahid Rajaee Teacher Training University, PO Box 16785-163, Tehran (Iran, Islamic Republic of); Khodadadi, Abbas Ali [Oil and Gas Processing Center of Excellence, School of Chemical Engineering, University of Tehran, 11155-4563 Tehran (Iran, Islamic Republic of)

2014-10-01

Highlights: • Hexagonally plate ZnO microstructure was synthesized by a simple hydrothermal method. • HRTEM images indicated a single crystal with a [0 0 1] direction growth. • DFT calculations were performed to reveal structure and electronic properties of ZnO. • The CO sensor response was close to obtained theoretical results. - Abstract: A simple low temperature hydrothermal method has been investigated for synthesis of single phase hexagonally plate ZnO microstructure. The synthesized ZnO was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) photoluminescence spectrum (PL) and ultraviolet and visible absorption spectroscopy (UV–vis) to investigate the surface morphology, crystallographic phase, optical properties and used as a sensor for detection of CO gas molecules. It was observed that the ZnO microstructures were uniform size, single phase and symmetrical, with a hexagonal shape and height of ∼250 nm. The optical band gap value of this sample was calculated to be about 3.22 eV, which show a red shift with theoretical method. High-resolution TEM images indicate that all the microstructures are single crystals with a [0 0 1] direction growth. We studied the gas response of this sample to 500 ppm CO over a temperature range of 200–400 °C and compared with theoretical results. Density functional theory (DFT) calculations were employed to investigate the structure and electronic properties of ZnO with simulating the adsorption process of CO gas on the ZnO (1 0 1) surface. The theoretical results were in good agreement with experimental results.

Experimental Study and Mathematical Modeling of Asphaltene Deposition Mechanism in Core Samples

Directory of Open Access Journals (Sweden)

Jafari Behbahani T.

2015-11-01

Full Text Available In this work, experimental studies were conducted to determine the effect of asphaltene deposition on the permeability reduction and porosity reduction of carbonate, sandstone and dolomite rock samples using an Iranian bottom hole live oil sample which is close to reservoir conditions, whereas in the majority of previous work, a mixture of recombined oil (a mixture of dead oil and associated gas was injected into a core sample which is far from reservoir conditions. The effect of the oil injection rate on asphaltene deposition and permeability reduction was studied. The experimental results showed that an increase in the oil injection flow rate can result in an increase in asphaltene deposition and permeability reduction. Also, it can be observed that at lower injection flow rates, a monotonic decrease in permeability of the rock samples can be attained upon increasing the injection flow rate, while at higher injection rates, after a decrease in rock permeability, an increasing trend is observed before a steady-state condition can be reached. The experimental results also showed that the rock type can affect the amount of asphaltene deposition, and the asphaltene deposition has different mechanisms in sandstone and carbonate core samples. It can be seen that the adsorption and plugging mechanisms have a more important role in asphaltene deposition in carbonate core samples than sandstone core samples. From the results, it can be observed that the pore volumes of the injected crude oil are higher for sandstone cores compared with the carbonate cores. Also, it can be inferred that three depositional types may take place during the crude oil injection, i.e., continuous deposition for low-permeability cores, slow, steady plugging for high-permeability cores and steady deposition for medium-permeability cores. It can be seen from the experimental results that damage to the core samples was found to increase when the production pressures were

Adsorption behavior of protein onto siloxane microspheres

International Nuclear Information System (INIS)

Liu Bailing; Cao Shunsheng; Deng Xiaobo; Li Songjun; Luo Rong

2006-01-01

The siloxane microspheres with core-shell structure (PMMA/PMPS) (MMA, methyl methacrylate; MPS, 3-methacryloxypropyl-trimethoxysilane) have been prepared by dispersion polymerization as described in our previous work. In this paper, the developed poly(MMA-MPS) microspheres, as a carrier, are used to investigate the adsorption behavior of bovine serum albumin (BSA) on them. The Langmuir and Freundlich models have been applied to describe the adsorption behavior. The experimental results indicated that the presence of PMPS evidently increases the adsorption rate and the amount of protein, and it also influences the interaction of BSA molecules. The adsorption of BSA on the poly(MMA-MPS) microspheres seems to be sensitive to pH and ionic strength. The fittings curves from Langmuir and Freundlich models showed that the adsorption was actually more complicated than ideal situation because one or more interactions were involved in the process. For understanding the electronic contribution, the Zeta potential was used to measure the reactive system before and after protein adsorption

Adsorption behavior of protein onto siloxane microspheres

Energy Technology Data Exchange (ETDEWEB)

Liu Bailing [Chengdu Institute of Organic Chemistry, Graduate School of CAS, Chinese Academy of Sciences, Chengdu 610041 (China)]. E-mail: Blliuchem@hotmail.com; Cao Shunsheng [Chengdu Institute of Organic Chemistry, Graduate School of CAS, Chinese Academy of Sciences, Chengdu 610041 (China); Deng Xiaobo [Chengdu Institute of Organic Chemistry, Graduate School of CAS, Chinese Academy of Sciences, Chengdu 610041 (China); Li Songjun [Chengdu Institute of Organic Chemistry, Graduate School of CAS, Chinese Academy of Sciences, Chengdu 610041 (China); Luo Rong [Chengdu Institute of Organic Chemistry, Graduate School of CAS, Chinese Academy of Sciences, Chengdu 610041 (China)

2006-09-15

The siloxane microspheres with core-shell structure (PMMA/PMPS) (MMA, methyl methacrylate; MPS, 3-methacryloxypropyl-trimethoxysilane) have been prepared by dispersion polymerization as described in our previous work. In this paper, the developed poly(MMA-MPS) microspheres, as a carrier, are used to investigate the adsorption behavior of bovine serum albumin (BSA) on them. The Langmuir and Freundlich models have been applied to describe the adsorption behavior. The experimental results indicated that the presence of PMPS evidently increases the adsorption rate and the amount of protein, and it also influences the interaction of BSA molecules. The adsorption of BSA on the poly(MMA-MPS) microspheres seems to be sensitive to pH and ionic strength. The fittings curves from Langmuir and Freundlich models showed that the adsorption was actually more complicated than ideal situation because one or more interactions were involved in the process. For understanding the electronic contribution, the Zeta potential was used to measure the reactive system before and after protein adsorption.

Electrochemical study of varenicline adsorptive behaviour and its interaction with DNA

Directory of Open Access Journals (Sweden)

Radulović Valentina

2012-01-01

Full Text Available The electrochemical behaviour of novel nicotinic α4β2 subtype receptor partial agonist varenicline (VAR which is used for smoking cessation, was investigated in Britton-Robinson buffers (pH 2.0-12.0 by cyclic, differential pulse and square wave voltammetry at a hanging mercury drop elctrode. The influence of pH, scan rate, concentration, accumulation potential and time on peak current and potential suggested that in alkaline media the redox process was adsorption controlled. Also, the experimental value of surface coverage, G = 1.03´10-10 mol cm-2, was used to determine the conditions when VAR was fully adsorbed at the electrode surface. Having in mind potential high toxicity of VAR due to the presence of quinoxaline structure, its interaction with DNA was postulated, and studied when both compounds were in the adsorbed state at modified HMDE. Using adsorptive transfer technique, the changes in potential and decrease in normalized peak currents were observed. The estimated value of the ratio of surface-binding constants indicated that the reduced form of VAR interacted with dsDNA more strongly than the oxidized form. Subtle DNA damage under conditions of direct DNA-VAR interaction at room temperature was observed. The proposed type of interaction was an intercalation. This study used simple electroanalytical methodology and showed the potential of DNA/HMDE biosensor for investigation of genotoxic effects.

Studies on the adsorption behavior of CO2-CH4 mixtures using activated carbon

Directory of Open Access Journals (Sweden)

R. B. Rios

2013-12-01

Full Text Available Separation of CO2 from CO2-CH4 mixtures is an important issue in natural gas and biogas purification. The design of such separation processes depends on the knowledge of the behavior of multicomponent adsorption, particularly that of CO2-CH4 mixtures. In this study, we present a series of experimental binary equilibrium isotherms for CO2-CH4 mixtures on an activated carbon at 293 K and compare them with predicted values using the Ideal Adsorption Solution Theory (IAST and the Extended Langmuir (EL model. Even at concentrations of ca. 20% for all binary isotherms, CO2 already presents higher adsorbed amounts with respect to CH4. A maximum selectivity of around 8.7 was observed for a nearly equimolar mixture at 0.1 MPa. The IAST in conjunction with the Toth equation showed slightly better results than IAST using the Langmuir equation and both showed better results than the EL model.

Application of superparamagnetic microspheres for affinity adsorption and purification of glutathione

International Nuclear Information System (INIS)

Wang Qiang; Guan Yueping; Yang Mingzhu

2012-01-01

The superparamagnetic poly-(MA–DVB) microspheres with micron size were synthesized by the modified suspension polymerization method. Adsorption of glutathione by magnetic poly-(MA–DVB) microspheres with IDA-copper was investigated. The effect of solution pH value, affinity adsorption and desorption of glutathione was studied. The results showed that the optimum pH value for glutathione adsorption was found at pH=3.5, the maximum capacity for glutathione of magnetic poly-(MA–DVB) microspheres was estimated at 42.4 mg/g by fitting the experimental data to the Langmuir equation. The adsorption equilibrium of glutathione was obtained in about 10 min and the adsorbed glutathione was desorbed from the magnetic microspheres in about 30 min using NaCl buffer solution. The magnetic microspheres could be repeatedly utilized for the affinity adsorption of glutathione. - Highlights: ► The magnetic microsphere with surface IDA–Cu groups was synthesized. ► The magnetic microspheres were applied for adsorption of GSH. ► The adsorption–desorption of glutathione was investigated. ► The maximum adsorption capacity of GSH was fitted at 42.4 mg/g.

Adsorption Removal of Glycidyl Esters from Palm Oil and Oil Model Solution by Using Acid-Washed Oil Palm Wood-Based Activated Carbon: Kinetic and Mechanism Study.

Science.gov (United States)

Cheng, Weiwei; Liu, Guoqin; Wang, Xuede; Han, Lipeng

2017-11-08

Acid-washed oil palm wood-based activated carbon (OPAC) has been investigated for its potential application as a promising adsorbent in the removal of glycidyl esters (GEs) from both palm oil and oil model (hexadecane) solution. It was observed that the removal rate of GEs in palm oil was up to >95%, which was significantly higher than other adsorbents used in this study. In batch adsorption system, the adsorption efficiency and performance of acid-washed OPAC were evaluated as a function of several experimental parameters such as contact time, initial glycidyl palmitate (PGE) concentration, adsorbent dose, and temperature. The Langmuir, Freundlich, and Dubinin-Radushkevich models were used to describe the adsorption equilibrium isotherm, and the equilibrium data were fitted best by the Langmuir model. The maximum adsorption capacity of acid-washed OPAC was found to be 36.23 mg/g by using the Langmuir model. The thermodynamic analysis indicated that the adsorption of PGE on acid-washed OPAC was an endothermic and physical process in nature. The experimental data were fitted by using pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. It was found that the kinetic of PGE adsorption onto acid-washed OPAC followed well the pseudo-second-order model for various initial PGE concentrations and the adsorption process was controlled by both film diffusion and intraparticle diffusion. The desorption test indicated the removal of GEs from palm oil was attributed to not only the adsorption of GEs on acid-washed OPAC, but also the degradation of GEs adsorbed at activated sites with acidic character. Furthermore, no significant difference between before and after PGE adsorption in oil quality was observed.

Isotherm, Kinetic and Thermodynamic Characteristics for Adsorption of Congo Red by Activated Carbon

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Jib [Kongju National University, Cheonan (Korea, Republic of)

2015-02-15

Batch experiment studies were carried out for adsorption of congo red using granular activated carbon with various parameters such as activated carbon dose, pH, initial dye concentration, temperature and contact time. Equilibrium experimental data are fitted to the Langmuir, Freundlich, Temkin and Dubin-Radushkevich isotherm equations. From Freundlich's separation factor (1/n) estimated, adsorption could be employed as effective treatment method for adsorption of congo red from aqueous solution. Base on Temkin constant (B) and Dubinin-Radushkevich constant (E), this adsorption process is physical adsorption. Adsorption kinetics has been tested using pseudo-first order and pseudo second order models. The results followed pseudo second order model with good correlation. Adsorption process of congo red on granular activated carbon was endothermic (ΔH=42.036 kJ/mol) and was accompanied by decrease in Gibbs free energy (ΔG=-2.414 to -4.596 kJ/mol) with increasing adsorption temperature.

Isotherm, Kinetic and Thermodynamic Characteristics for Adsorption of Congo Red by Activated Carbon

International Nuclear Information System (INIS)

Lee, Jong Jib

2015-01-01

Batch experiment studies were carried out for adsorption of congo red using granular activated carbon with various parameters such as activated carbon dose, pH, initial dye concentration, temperature and contact time. Equilibrium experimental data are fitted to the Langmuir, Freundlich, Temkin and Dubin-Radushkevich isotherm equations. From Freundlich's separation factor (1/n) estimated, adsorption could be employed as effective treatment method for adsorption of congo red from aqueous solution. Base on Temkin constant (B) and Dubinin-Radushkevich constant (E), this adsorption process is physical adsorption. Adsorption kinetics has been tested using pseudo-first order and pseudo second order models. The results followed pseudo second order model with good correlation. Adsorption process of congo red on granular activated carbon was endothermic (ΔH=42.036 kJ/mol) and was accompanied by decrease in Gibbs free energy (ΔG=-2.414 to -4.596 kJ/mol) with increasing adsorption temperature

A study of uranium adsorption to single-crystal tungsten

Energy Technology Data Exchange (ETDEWEB)

Samin, Adib; Hastings, Aaron; Zhang, Jinsuo, E-mail: jzhang@osu.edu

2015-12-15

In this study we explore the adsorption of uranium to the (110) plane of tungsten. Potential functions were constructed to describe the interaction of adsorbed uranium atoms with the tungsten surface and the lateral interaction between adsorbed uranium atoms. Next, the behavior of the uranium adlayer under different conditions was studied through a Monte Carlo simulation of the grand canonical Hamiltonian in an off-lattice model. Our results are consistent with available studies in the literature. The simulation results indicate that the temperature and dipole–dipole interactions play an important role in governing the adsorption process.

A study of uranium adsorption to single-crystal tungsten

International Nuclear Information System (INIS)

Samin, Adib; Hastings, Aaron; Zhang, Jinsuo

2015-01-01

In this study we explore the adsorption of uranium to the (110) plane of tungsten. Potential functions were constructed to describe the interaction of adsorbed uranium atoms with the tungsten surface and the lateral interaction between adsorbed uranium atoms. Next, the behavior of the uranium adlayer under different conditions was studied through a Monte Carlo simulation of the grand canonical Hamiltonian in an off-lattice model. Our results are consistent with available studies in the literature. The simulation results indicate that the temperature and dipole–dipole interactions play an important role in governing the adsorption process.

MSINDO quantum chemical modeling study of water molecule adsorption at nano-sized anatase TiO2 surfaces

International Nuclear Information System (INIS)

Wahab, Hilal S.; Bredow, Thomas; Aliwi, Salah M.

2008-01-01

In this work, we studied the adsorption of water molecule onto the (1 0 0), (0 1 0) and (0 0 1) surfaces of nano-sized anatase TiO 2 with semiempirical SCF MO method, MSINDO. The anatase TiO 2 particles are modeled with free clusters (TiO 2 ) n, where n = 20-80. Whereas, the surfaces have been modeled with two saturated clusters, Ti 21 O 58 H 32 and Ti 36 O 90 H 36 . The surface lattice fivefold coordinated titanium atoms (Ti 5C ), which represent the Lewis acid sites, are selected as adsorption centers. We also investigated the effect of TiO 2 cluster size on the computed band gap energy. Results reveal that the electronic properties of a cluster in the lowest excited state differ from that of the ground state. Furthermore, the MSINDO band gap energies of 3.68-3.77 eV for the anatase TiO 2 are in a fair accordance with other literature data. In agreement with other computational and experimental studies, the dissociated form of water molecule adsorption on anatase TiO 2 surfaces is always more stabilized than the molecular form

Characterization of trichloroethylene adsorption onto waste biocover soil in the presence of landfill gas.

Science.gov (United States)

He, Ruo; Su, Yao; Kong, Jiaoyan

2015-09-15

Waste biocover soils (WBS) have been demonstrated to have great potential in mitigating trichloroethylene (TCE) emission from landfills, due to the relatively high TCE-degrading capacity. In this study, the characteristics of TCE adsorption on WBS in the presence of the major landfill gas components (i.e., CH4 and CO2) were investigated in soil microcosms. The adsorption isotherm of TCE onto WBS was fitted well with linear model within the TCE concentrations of 7000 ppmv. The adsorption capacity of TCE onto WBS was affected by temperature, soil moisture content and particle size, of which, temperature was the dominant factor. The adsorption capacity of TCE onto the experimental materials increased with the increasing organic matter content. A significantly positive correlation was observed between the adsorption capacity of TCE and the organic matter content of experimental materials that had relatively higher organic content (r = 0.988, P = 0.044). To better understand WBS application in practice, response surface methodology was developed to predict TCE adsorption capacity and emissions through WBS in different landfills in China. These results indicated that WBS had high adsorption capacity of TCE in LFG and temperature should be paid more attention to manipulate WBS to reduce TCE emissions from landfills. Copyright © 2015 Elsevier B.V. All rights reserved.

Dyeing and Adsorption Studies of Madder (Rubia tinctorum on Wool Fibers

Directory of Open Access Journals (Sweden)

Mahmoud FEIZ

2015-03-01

Full Text Available In this study, the dyeing behavior of wool fabrics with madder has been studied. Three well-known types of adsorption isotherms i.e. the Nernst, Freundlich and Langmuir isotherms were used to fit the data. It was found that the adsorption isotherm of madder on wool fibers follows Freundlich type of adsorption. The exponent α in Freundlich isotherm equation (Cf = k.Csα was obtained 0.61 corresponding to 0.5 for the direct dyes on cellulosic fibers. The effect of salt and pH on dyeing of wool samples was investigated by the use of color characteristics measurements. The results showed that addition of salt and acid (pH 4.5 to the dyebath resulted in an increase of adsorption. DOI: http://dx.doi.org/10.5755/j01.ms.21.1.5150

Adsorption study of cadmium (II) and lead (II) on radish peels

International Nuclear Information System (INIS)

Anwar, J.; Shafique, U.; Salman, M.; Zaman, W.; Memoona, M.

2009-01-01

The removal efficiency of heavy metals like Cd(II) and Pb(II) from aqueous solutions by adsorption on Raphanus sativus (Radish peels) has been studied. The effects of time, pH, concentration of adsorbent and agitation speed on adsorption have been evaluated. It is found that radish peels powder has high removal efficiency for both the metals. Batch adsorption study has shown that Cd(II) and Pb(II) has been removed up to 88% and 86% respectively. Adsorption equilibriums for both metals have been described by the Langmuir isotherm. The maximum amount of heavy metals (Q ) adsorbed at max equilibrium were 7.5 and 1.23 mg/g for Cd(II) and Pb(II) respectively as evaluated by Langmuir isotherm. It is concluded that waste materials like radish peels can be used for removal of heavy metals from aqueous streams. (author)

Gallium adsorption on (0001) GaN surfaces

International Nuclear Information System (INIS)

Adelmann, Christoph; Brault, Julien; Mula, Guido; Daudin, Bruno; Lymperakis, Liverios; Neugebauer, Joerg

2003-01-01

We study the adsorption behavior of Ga on (0001) GaN surfaces combining experimental specular reflection high-energy electron diffraction with theoretical investigations in the framework of a kinetic model for adsorption and ab initio calculations of energy parameters. Based on the experimental results we find that for substrate temperatures and Ga fluxes typically used in molecular-beam epitaxy of GaN, finite equilibrium Ga surface coverages can be obtained. The measurement of a Ga/GaN adsorption isotherm allows the quantification of the equilibrium Ga surface coverage as a function of the impinging Ga flux. In particular, we show that a large range of Ga fluxes exists, where 2.5±0.2 monolayers (in terms of the GaN surface site density) of Ga are adsorbed on the GaN surface. We further demonstrate that the structure of this adsorbed Ga film is in good agreement with the laterally contracted Ga bilayer model predicted to be most stable for strongly Ga-rich surfaces [Northrup et al., Phys. Rev. B 61, 9932 (2000)]. For lower Ga fluxes, a discontinuous transition to Ga monolayer equilibrium coverage is found, followed by a continuous decrease towards zero coverage; for higher Ga fluxes, Ga droplet formation is found, similar to what has been observed during Ga-rich GaN growth. The boundary fluxes limiting the region of 2.5 monolayers equilibrium Ga adsorption have been measured as a function of the GaN substrate temperature giving rise to a Ga/GaN adsorption phase diagram. The temperature dependence is discussed within an ab initio based growth model for adsorption taking into account the nucleation of Ga clusters. This model consistently explains recent contradictory results of the activation energy describing the critical Ga flux for the onset of Ga droplet formation during Ga-rich GaN growth [Heying et al., J. Appl. Phys. 88, 1855 (2000); Adelmann et al., J. Appl. Phys. 91, 9638 (2002).

On thermodynamics of methane+carbonaceous materials adsorption

KAUST Repository

Rahman, Kazi Afzalur

2012-01-01

This study presents the theoretical frameworks for the thermodynamic quantities namely the heat of adsorption, specific heat capacity, entropy, and enthalpy for the adsorption of methane onto various carbonaceous materials. The proposed theoretical frameworks are developed from the rigor of thermodynamic property surfaces of a single component adsorbate-adsorbent system and by incorporating the micropore filling theory approach, where the effect of adsorbed phase volume is considered. The abovementioned thermodynamic properties are quantitatively evaluated from the experimental uptake data for methane adsorption onto activated carbons such as Maxsorb III at temperatures ranging from 120 to 350 K and pressures up to 25 bar. Employing the proposed thermodynamic approaches, this paper shows the thermodynamic maps of the charge and discharge processes of adsorbed natural gas (ANG) storage system for understanding the behaviors of natural gas in ANG vessel. © 2011 Elsevier Ltd. All rights reserved.

Study on the adsorption isosteres of the composite adsorbent CaCl2 and expanded graphite

International Nuclear Information System (INIS)

Li, S.L.; Wu, J.Y.; Xia, Z.Z.; Wang, R.Z.

2011-01-01

A test setup was built to study the adsorption performance of the composite adsorbent used in the adsorption system. The isovolume measurement method is adopted in the test setup to measure the adsorption isosteres of the composite adsorbent and ammonia working pair. The adsorption isosteres are the curves of the adsorption pressures variation with adsorption temperatures at constant adsorption quantity, which are convenient for the calculation of the adsorption heat and selection of the adsorption working pairs. The adsorption heats were calculated according to the adsorption isosteres, three clear crest values indicate that there were three types of reaction during the reaction processes of ammoniate calcium chloride and ammonia. The kinetic model of adsorption isosteres is obtained by the Temkin model, it is useful to estimate the adsorption performance of the working pairs and useful to guide the design of adsorption system.

Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): Fixed-bed column study

International Nuclear Information System (INIS)

Nguyen, T.A.H.; Ngo, H.H.; Guo, W.S.; Pham, T.Q.; Li, F.M.; Nguyen, T.V.; Bui, X.T.

2015-01-01

This study explores the potential of removing phosphorus from aqueous solutions and sewage by Zr(IV)-loaded okara (ZLO) in the fixed-bed column. Soybean residue (okara) was impregnated with 0.25 M Zr(IV) solution to prepare active binding sites for phosphate. The effect of several factors, including flow rate, bed height, initial phosphorus concentration, pH and adsorbent particle size on the performance of ZLO was examined. The maximum dynamic adsorption capacity of ZLO for phosphorus was estimated to be 16.43 mg/g. Breakthrough curve modeling indicated that Adams–Bohart model and Thomas model fitted the experimental data better than Yoon–Nelson model. After treatment with ZLO packed bed column, the effluent could meet the discharge standard for phosphorus in Australia. Successful desorption and regeneration were achieved with 0.2 NaOH and 0.1 HCl, respectively. The results prove that ZLO can be used as a promising phosphorus adsorbent in the dynamic adsorption system. - Highlights: • Dynamic adsorption of P from water and wastewater by Zr(IV)-loaded okara was tested. • Effects of column design parameters on the adsorption performance were investigated. • The dynamic adsorption capacity of Zr(IV)-loaded okara for P was reasonably high. • The spent column was effectively regenerated with 0.2 M NaOH followed by 0.1 M HCl. • Zr(IV)-loaded okara column was efficient in eliminating P from municipal sewage

Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): Fixed-bed column study

Energy Technology Data Exchange (ETDEWEB)

Nguyen, T.A.H. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Ngo, H.H., E-mail: ngohuuhao121@gmail.com [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Guo, W.S. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Pham, T.Q. [Faculty of Geography, University of Science, Vietnam National University, Hanoi (Viet Nam); Li, F.M. [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); Nguyen, T.V. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Bui, X.T. [Environmental Engineering and Management Research Group, Ton Duc Thang University, Ho Chi Minh City (Viet Nam); Faculty of Environment and Natural Resources, Ho Chi Minh City University of Technology-Vietnam National University, Ho Chi Minh City (Viet Nam)

2015-08-01

This study explores the potential of removing phosphorus from aqueous solutions and sewage by Zr(IV)-loaded okara (ZLO) in the fixed-bed column. Soybean residue (okara) was impregnated with 0.25 M Zr(IV) solution to prepare active binding sites for phosphate. The effect of several factors, including flow rate, bed height, initial phosphorus concentration, pH and adsorbent particle size on the performance of ZLO was examined. The maximum dynamic adsorption capacity of ZLO for phosphorus was estimated to be 16.43 mg/g. Breakthrough curve modeling indicated that Adams–Bohart model and Thomas model fitted the experimental data better than Yoon–Nelson model. After treatment with ZLO packed bed column, the effluent could meet the discharge standard for phosphorus in Australia. Successful desorption and regeneration were achieved with 0.2 NaOH and 0.1 HCl, respectively. The results prove that ZLO can be used as a promising phosphorus adsorbent in the dynamic adsorption system. - Highlights: • Dynamic adsorption of P from water and wastewater by Zr(IV)-loaded okara was tested. • Effects of column design parameters on the adsorption performance were investigated. • The dynamic adsorption capacity of Zr(IV)-loaded okara for P was reasonably high. • The spent column was effectively regenerated with 0.2 M NaOH followed by 0.1 M HCl. • Zr(IV)-loaded okara column was efficient in eliminating P from municipal sewage.

Perchlorate adsorption by granular activated carbon modified with cetyl trimethyl ammonium chloride

International Nuclear Information System (INIS)

Yin-Xian, P.; Lu, Z.; Cui-Yun, C.; Ming-Long, Z.; Yang, Z.; Chun-Du, W.

2012-01-01

To improve the adsorption of perchlorate (ClO/sub 4/ in contaminated water, granular activated carbon (GAC) was modified with cetyl trimethyl ammonium chloride (CTAC). To investigate the adsorption mechanism of perchlorate the structure of GAC-CTAC was characterized by scanning electron microscopy (SEM) and FTIR spectroscopy. Then the GAC-CTAC was used for the adsorption of perchlorate in water. The effects of the adsorption time, pH, initial ClO/sub 4/ concentration, and co-existed anions on perchlorate adsorbed by GAC-CTAC were studied. The results show that the GAC-CTAC could absorb perchlorate better in water. The adsorption capacity of perchlorate on GAC-CTAC decreases in the alkaline solution, and increases with increasing the - initial concentration. The competitive adsorption exists between co-existed anions and ClO/sub 4/ on GAC-CTAC. In addition, adsorption of ClO/sub 4/ on GAC-CTAC fits the Langmuir, Freundlich and Tempkin isothermal models in the range of the experimental concentration. The adsorption process follows pseudo-second order kinetics. (author)

Remediation of Groundwater Polluted by Aromatic Compounds by Means of Adsorption

Directory of Open Access Journals (Sweden)

Silvana Canzano

2014-07-01

Full Text Available In this work, an experimental and modeling analysis of the adsorption of four aromatic compounds (i.e., toluene, naphthalene, o-xylene and ethylbenzene onto a commercial activated carbon is carried out. The aim is to assess the suitability of the adsorption process for the treatment of polluted groundwater, also when a multiple contamination is detected. Batch adsorption tests from simulated polluted groundwater are performed in single-compound systems and in two binary systems (i.e., toluene + naphthalene and o-xylene + ethylbenzene, at constant temperature (20 °C and pH (7. Experimental results in single-compound systems reveal that all of the analytes are significantly adsorbed on the tested activated carbon. In particular, toluene and naphthalene adsorption capacities are the highest and of similar value, while for o-xylene and ethylbenzene, the performances are lower. The adsorption of these compounds seems to be influenced by a combined effect of several parameters, such as hydrophobicity, molecule size, structure of the molecule, etc. Experimental results in binary systems show a different behavior of the two systems, which confirms their complexity and explains the interest in these complex adsorption systems. In particular, toluene and naphthalene are mutually competitive, while in the case of o-xylene + ethylbenzene, only the former undergoes competitive effects. The analysis of the entire experimental data set is integrated with a dedicated modeling analysis using the extended Langmuir model. For both single-compound and binary systems, this model provides acceptable results, in particular for low equilibrium concentrations, like those more commonly found in groundwater, and for the compounds involved in adsorptive competitive effects.

Adsorption of toxic metal ion Cr(VI) from aqueous state by TiO2-MCM-41: equilibrium and kinetic studies.

Science.gov (United States)

Parida, Kulamani; Mishra, Krushna Gopal; Dash, Suresh Kumar

2012-11-30

This paper deals with the immobilization of various weight percentage of TiO(2) on mesoporous MCM-41, characterization of the materials by X-ray diffraction (XRD), nitrogen adsorption-desorption, Fourier Transform Infrared (FTIR) analysis, UV-vis diffuse reflectance spectroscopy (DRS) and evaluation of the adsorption capacity toward Cr(VI) removal. It is found that the MCM-41 structure retained after loading of TiO(2) but the surface area and pore diameter decreased due to pore blockage. Adsorption of Cr(VI) from aqueous state was investigated on TiO(2)-MCM-41 by changing various parameters such as pH, metal ion concentration, and the temperature. When TiO(2) loading was more than 20 wt.%, the adsorption activity (25)TiO(2)-MCM-41 reduced significantly due to considerable decrease in the surface area. It is also observed that TiO(2) and neat MCM-41 exhibits very less Cr(VI) adsorption compared to TiO(2)-MCM-41. The adsorption of Cr(VI) onto (20)TiO(2)-MCM-41 at pH~5.5 and temperature 323 K was 91% at 100mg/L Cr(VI) metal ion concentration in 80 min. The experimental data fitted well to Langmuir and Freundlich isotherms. The adsorption of Cr(VI) on TiO(2)-MCM-41 followed a second order kinetics with higher values of intra-particle diffusion rate. Thermodynamic parameters suggested that the adsorption process is endothermic in nature and desorption studies indicated a chemisorption mode. Copyright © 2012 Elsevier B.V. All rights reserved.

RPBE-vdW Description of Benzene Adsorption on Au(111)

DEFF Research Database (Denmark)

Pedersen, Jess Wellendorff; Kelkkanen, Kari André; Mortensen, Jens Jørgen

2010-01-01

Density functional theory has become a popular methodology for the analysis of molecular adsorption on surfaces. Despite this popularity, there exist adsorption systems for which commonly used exchange-correlation functionals fail miserably. Particularly those systems where binding is due to van...... der Waals interactions. The adsorption of benzene on Au(111) is an often mentioned such system where standard density functionals predict a very weak adsorption or even a repulsion, whereas a significant adsorption is observed experimentally. We show that a considerable improvement in the description...... of the adsorption of benzene on Au(111) is obtained when using the so-called RPBE-vdW functional....

Experimental Study and modelling of the Sorption of Selenite and Europium Onto Smectite and Illite Clays

Energy Technology Data Exchange (ETDEWEB)

Missana, T.; Alonso, U.; Garcia-Gutierrez, M.

2009-10-12

This study provides a large set of experimental selenite sorption data for pure smectite and illite. Similar sorption behavior existed in both clays: linear within a large range of the Se concentrations investigated and independent of ionic strength. Selenite sorption was also analysed in the illite/smectite system with the clays mixed in two different proportions. The objective of the study was to provide the simplest model possible to fit the experimental data, a model also capable of describing selenite sorption in binary illite/smectite clay systems. Selenite sorption data were modeled using both a one-and a two-site non-electrostatic model that took into account the formation of two complexes at the edge sites of the clay. The complexation constants obtained by fitting sorption data of the individual minerals were incorporated into a model to predict the adsorption of selenium in the illite/ smectite mixtures; the models predictions were consistent with the experimental adsorption data. (Author) 42 refs.

Experimental Study and modelling of the Sorption of Selenite and Europium Onto Smectite and Illite Clays

International Nuclear Information System (INIS)

Missana, T.; Alonso, U.; Garcia-Gutierrez, M.

2009-01-01

This study provides a large set of experimental selenite sorption data for pure smectite and illite. Similar sorption behavior existed in both clays: linear within a large range of the Se concentrations investigated and independent of ionic strength. Selenite sorption was also analysed in the illite/smectite system with the clays mixed in two different proportions. The objective of the study was to provide the simplest model possible to fit the experimental data, a model also capable of describing selenite sorption in binary illite/smectite clay systems. Selenite sorption data were modeled using both a one-and a two-site non-electrostatic model that took into account the formation of two complexes at the edge sites of the clay. The complexation constants obtained by fitting sorption data of the individual minerals were incorporated into a model to predict the adsorption of selenium in the illite/ smectite mixtures; the models predictions were consistent with the experimental adsorption data. (Author) 42 refs

Adsorption Properties of Doxorubicin Hydrochloride onto Graphene Oxide: Equilibrium, Kinetic and Thermodynamic Studies

Directory of Open Access Journals (Sweden)

Zonghua Wang

2013-05-01

Full Text Available Doxorubicin hydrochloride (DOX is an effective anticancer agent for leukemia chemotherapy, although its clinical use has been limited because of its side effects such as cardiotoxicity, alopecia, vomiting, and leucopenia. Attention has been focussed on developing new drug carriers with high adsorption capacity and rapid adsorption rate in order to minimize the side effects of DOX. Graphene oxide (GO, a new type of nanomaterial in the carbon family, was prepared by Hummers method and used as adsorbent for DOX from aqueous solution. The physico-chemical properties of GO were characterized by transmission electron microscope (TEM, Fourier transform infrared spectroscopy (FTIR, zeta potential, and element analysis. The adsorption properties of DOX on GO were studied as a function of contact time, adsorbent dosage, temperature and pH value. The results showed that GO had a maximum adsorption capacity of 1428.57 mg/g and the adsorption isotherm data fitted the Langmuir model. The kinetics of adsorption fits a pseudo-second-order model. The thermodynamic studies indicate that the adsorption of DOX on GO is spontaneous and endothermic in nature.

Dimethyl methylphosphonate adsorption and decomposition on MoO2 as studied by ambient pressure x-ray photoelectron spectroscopy and DFT calculations

Science.gov (United States)

Head, Ashley R.; Tsyshevsky, Roman; Trotochaud, Lena; Yu, Yi; Karslıoǧlu, Osman; Eichhorn, Bryan; Kuklja, Maija M.; Bluhm, Hendrik

2018-04-01

Organophosphonates range in their toxicity and are used as pesticides, herbicides, and chemical warfare agents (CWAs). Few laboratories are equipped to handle the most toxic molecules, thus simulants such as dimethyl methylphosphonate (DMMP), are used as a first step in studying adsorption and reactivity on materials. Benchmarked by combined experimental and theoretical studies of simulants, calculations offer an opportunity to understand how molecular interactions with a surface changes upon using a CWA. However, most calculations of DMMP and CWAs on surfaces are limited to adsorption studies on clusters of atoms, which may differ markedly from the behavior on bulk solid-state materials with extended surfaces. We have benchmarked our solid-state periodic calculations of DMMP adsorption and reactivity on MoO2 with ambient pressure x-ray photoelectron spectroscopy studies (APXPS). DMMP is found to interact strongly with a MoO2 film, a model system for the MoO x component in the ASZM-TEDA© gas filtration material. Density functional theory modeling of several adsorption and decomposition mechanisms assist the assignment of APXPS peaks. Our results show that some of the adsorbed DMMP decomposes, with all the products remaining on the surface. The rigorous calculations benchmarked with experiments pave a path to reliable and predictive theoretical studies of CWA interactions with surfaces.

Theoretical study of simultaneous water and VOCs adsorption and desorption in a silica gel rotor

DEFF Research Database (Denmark)

Zhang, G.; Zhang, Y.F.; Fang, Lei

2008-01-01

One-dimensional partial differential equations were used to model the simultaneous water and VOC (Volatile Organic Compound) adsorption and desorption in a silica gel rotor which was recommended for indoor air cleaning. The interaction among VOCs and moisture in the adsorption and desorption...... process was neglected in the model as the concentrations of VOC pollutants in typical indoor environment were much lower than that of moisture and the adsorbed VOCs occupied only a minor portion of adsorption capacity of the rotor. Consequently VOC transfer was coupled with heat and moisture transfer only...... by the temperatures of the rotor and the air stream. The VOC transfer equations were solved by discretizing them into explicit up-wind finite differential equations. The model was validated with experimental data. The calculated results suggested that the regeneration time designed for dehumidification may...

Phenomenological studies and modelling of the gaseous impurities oxidation and adsorption mechanisms in helium: application for the purification system optimization in gas cooled nuclear reactors

International Nuclear Information System (INIS)

Legros, F.

2008-01-01

In GEN IV studies on future fission nuclear reactors, two concepts using helium as a coolant have been selected: GFR and VHTR. Among radioactive impurities and dusts, helium can contain H 2 , CO, CH 4 , CO 2 , H 2 O, O 2 , as well as nitrogenous species. To optimize the reactor functioning and lifespan, it is necessary to control the coolant chemical composition using a dedicated purification system. A pilot designed at the CEA allows studying this purification system. Its design includes three unit operations: H 2 and CO oxidation on CuO, then two adsorption steps. This study aims at providing a detailed analysis of the first and second purification steps, which have both been widely studied experimentally at laboratory scale. A first modelling based on a macroscopic approach was developed to represent the behaviour of the reactor and has shown that the CuO fixed bed conversion is dependent on the chemistry (mass transfer is not an issue) and is complete. The results of the structural analysis of the solids allow considering the CuO as particles made of 200 nm diameter grains. Hence, a new model at grain scale is proposed. It is highlighted that the kinetic constants from these two models are related with a scale factor which depends on geometry. A competition between carbon monoxide and hydrogen oxidation has been shown. Activation energies are around 30 kJ.mol-1. Simulation of the simultaneous oxidations leads to consider CO preferential adsorption. A similar methodology has been applied for CO 2 and H 2 O adsorption. The experimental isotherms showed a Langmuir type adsorption. Using this model, experimental and theoretical results agree. (author) [fr

Studies on the adsorption characteristics of some heavy elements using Vermiculite

International Nuclear Information System (INIS)

Ezz El Deen, A.A.; Waly, S.A.; EL Adham, K.A.; Dakroury, A.M.; Shoukry, M.M

2012-01-01

The uncontrolled release of liquid wastes into the environment may lead to hazard to the human and the environment. There have been extensive studies for development of various technologies for removal of Cd 2+ and Co 2+ from wastes The removal of Cd 2+ and Co 2+ ions from aqueous solution by Vermiculite has been investigated. The Vermiculite was characterized by Particle size, Surface area, and chemical analysis. The adsorption behavior of Vermiculite has been studied as a function of the solution agitation time, ph, initial metal concentration in solution, particle size, and temperature. Kinetic studies were undertaken to show the mechanistic aspects of the process. It was showed that the process was first order reaction for the two metal ions. Sorption data have been correlated with both, Langmuir and Freundlich adsorption models. Thermodynamic parameters such as ΔH degree, ΔS degree, and ΔG degree were calculated from the slope and intercept of linear plot of lnK D against 1/T. The ΔH degree and ΔG degree values of metal ions adsorption on the two adsorbents show endothermic heat of adsorption. But there is a negative free energy value, indicating that the process of ions adsorption is favored at high temperatures.

Adsorption studies on bleaching of palm-kernel oil with activated ...

African Journals Online (AJOL)

Adsorption studies were performed on bleaching of palm-kernel oil (PKO) with different weight ratios of activated bentonite clay/PKO, ranging from 0.25% to 3% and at different temperatures of 70ºC, 80ºC, 90ºC and 100ºC. The equilibrium data generated were subsequently fitted with Langmuir and Freundlich adsorption ...

Study on adsorption refrigeration performance of MIL-101-isobutane working pair

International Nuclear Information System (INIS)

Ma, Liejun; Yang, Huan; Wu, Qi; Yin, Yu; Liu, Zongjian; Cui, Qun; Wang, Haiyan

2015-01-01

Rising concerns about pro-environment and energy conservation bring about the escalating interests in adsorption cooling systems using renewable energy. Adsorption chillers with common refrigerants (water, ethanol, methanol, etc.) face the problem that advanced technologies and intricate design considerations are required to maintain high vacuum. This paper aims at the parameters optimization of adsorption system being operated with the novel working pair, MIL-101-isobutane, under typical conditions of ice making and air-condition. Adsorption isotherms and dynamic of isobutane on MIL-101 are discussed simultaneously. When the hot water inlet temperature, cooling water temperature and desorption time are 95 °C, 30 °C and 30 min, respectively, the cooling capacity is 45.7 kJ/kg, which is 1.7 times as much as that of activated carbon–isobutane pair. Structural stability of MIL-101 subjected to 500 times adsorption/desorption cycles has been successfully verified by XRD (X-ray diffraction). - Highlights: • Adsorption isotherms and kinetic of isobutane on MIL-101 were studied. • A single bed adsorption chiller with MIL-101-isobutane pair was built. • System performed better than that using activated carbon–isobutane pair. • Stability of MIL-101 subjected to 500 ad/desorption cycles has been verified.

Fixed bed adsorption of hexavalent chromium onto natural zeolite from air stream

OpenAIRE

F. Golbabaei; E. Rahmanzadeh; G. R. Moussavi; A. Faghihi zarandi; M. R. Baneshi

2014-01-01

Introduction: Chromium (VI) is a known human carcinogenic agent which is used in numerous industrial processes such as electroplating, welding, textile, cement and steel fabrication. The aim of this study was to determine the effectiveness of natural zeolite on the fixed bed adsorption of Cr (VI) from air stream. . Material and Method: In this experimental study, chromium mists were generated by a nebulizer (3A model, Italy). Performance of natural zeolite in the Cr (VI) adsorption and ...

Equilibrium and Kinetics Study of Adsorption of Crystal Violet onto the Peel of Cucumis sativa Fruit from Aqueous Solution

Directory of Open Access Journals (Sweden)

T. Smitha

2012-01-01

Full Text Available The use of low-cost, locally available, high efficiency and eco-friendly adsorbents has been investigated as an ideal alternative to the current expensive methods of removing dyes from wastewater. This study investigates the potential use of the peel of Cucumis sativa fruit for the removal of crystal violet (CV dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH and contact time were investigated and optimal experimental conditions were ascertained. The results showed that as the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was determined as 7.0. The adsorption of crystal violet followed pseudo-second order rate equation and fit well Langmuir and Freundlich equations. The maximum removal of CV was obtained at pH 7 as 92.15% for adsorbent dose of 0.2 g/50 mL and 25 mg L-1 initial dye concentration at room temperature. The maximum adsorption capacity obtained from Langmuir equation was 34.24 mg g-1. Furthermore, adsorption kinetics of (CV was studied and the rate of adsorption was found to conform to pseudo-second order kinetics with a good correlation (R2 > 0.9739. The peel of Cucumis sativa fruit can be attractive options for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater show better removal percentage of (CV.

Theoretical and experimental study of redox processes combined with adsorption phenomena under conditions of square-wave voltammetry

OpenAIRE

Gulaboski, Rubin

2001-01-01

Theoretical models of four electrode reactions coupled with adsorption phenomena under conditions of square-wave voltammetry are developed: simple surface redox reaction, surface catalytic reaction, cathodic stripping reaction of I order, and cathodic stripping reaction of II order.

Surfactant-impregnated activated carbon for enhanced adsorptive removal of Ce(IV) radionuclides from aqueous solutions

International Nuclear Information System (INIS)

Mahmoud, Mamdoh R.; Sharaf El-deen, Gehan E.; Soliman, Mohamed A.

2014-01-01

Highlights: • Activated carbon (AC) was impregnated in this work with CTAB and NaLS surfactants. • The materials were evaluated as a sorbent for adsorption of Ce(IV) radionuclides. • Adsorption capacity of AC–NaLS for Ce(IV) is two-times the capacity of AC. • The kinetic and equilibrium data are fitted to pseudo-second-order and D–R models. • The results suggest the applicability of surface modified AC for waste treatment. - Abstract: The surfactants cetyltrimethylammonium bromide (CTAB) and sodium lauryl sulfate (NaLS) were utilized for modifying the activated carbon’s surface. The materials were characterized using BET–N 2 , scanning electron microscope, and Fourier transform infrared (FT-IR) spectroscopy. Adsorption of Ce(IV) radionuclides from aqueous solutions by activated carbon (AC) and surfactant-impregnated AC was studied. The obtained data showed that adsorption of Ce(IV) is strongly dependent on the solution pH and AC–NaLS exhibits the widest pH-range of maximum removal. The experimental adsorption capacity of AC–NaLS (0.069 mmol/g) for Ce(IV) is found to be nearly twice greater than that of AC (0.036 mmol/g). The adsorption kinetics of Ce(IV) onto AC and AC–NaLS were analyzed by linear and non-linear fittings to the pseudo-first-order, pseudo-second-order and Elovich kinetic models. Of these models, the pseudo-second-order is the best kinetic expression for describing the experimental data. The diffusion studies indicated that adsorption of Ce(IV) radionuclides on AC and AC–NaLS is controlled by film diffusion. Linear and non-linear fittings of the adsorption equilibrium data for Ce(IV) onto AC and AC–NaLS revealed that the Dubinin–Radushkevich (D–R) isotherm model fits the experimental data better than Freundlich and Langmuir models. The values of adsorption free energy, E, calculated from both linear and non-linear methods suggested that Ce(IV) radionuclides are physically adsorbed onto AC and AC–NaLS

Adsorption of trichloroethylene and benzene vapors onto hypercrosslinked polymeric resin

Energy Technology Data Exchange (ETDEWEB)

Liu Peng [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); Long Chao, E-mail: clong@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal and Resources Reuse, Nanjing 210046 (China); Jiangsu Engineering Research Center for Organic Pollution Control and Resources Reuse, Nanjing 210046 (China); Li Qifen [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); Qian Hongming [State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal and Resources Reuse, Nanjing 210046 (China); Jiangsu Engineering Research Center for Organic Pollution Control and Resources Reuse, Nanjing 210046 (China); Li Aimin; Zhang Quanxing [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210093 (China); State Environmental Protection Engineering Center for Organic Chemical Industrial Waste Water Disposal and Resources Reuse, Nanjing 210046 (China); Jiangsu Engineering Research Center for Organic Pollution Control and Resources Reuse, Nanjing 210046 (China)

2009-07-15

In this research, the adsorption equilibria of trichloroethylene (TCE) and benzene vapors onto hypercrosslinked polymeric resin (NDA201) were investigated by the column adsorption method in the temperature range from 303 to 333 K and pressures up to 8 kPa for TCE, 12 kPa for benzene. The Toth and Dubinin-Astakov (D-A) equations were tested to correlate experimental isotherms, and the experimental data were found to fit well by them. The good fits and characteristic curves of D-A equation provided evidence that a pore-filling phenomenon was involved during the adsorption of TCE and benzene onto NDA-201. Moreover, thermodynamic properties such as the Henry's constant and the isosteric enthalpy of adsorption were calculated. The isosteric enthalpy curves varied with the surface loading for each adsorbate, indicating that the hypercrosslinked polymeric resin has an energetically heterogeneous surface. In addition, a simple mathematic model developed by Yoon and Nelson was applied to investigate the breakthrough behavior on a hypercrosslinked polymeric resin column at 303 K and the calculated breakthrough curves were in high agreement with corresponding experimental data.

Adsorption of trichloroethylene and benzene vapors onto hypercrosslinked polymeric resin.

Science.gov (United States)

Liu, Peng; Long, Chao; Li, Qifen; Qian, Hongming; Li, Aimin; Zhang, Quanxing

2009-07-15

In this research, the adsorption equilibria of trichloroethylene (TCE) and benzene vapors onto hypercrosslinked polymeric resin (NDA201) were investigated by the column adsorption method in the temperature range from 303 to 333 K and pressures up to 8 kPa for TCE, 12 kPa for benzene. The Toth and Dubinin-Astakov (D-A) equations were tested to correlate experimental isotherms, and the experimental data were found to fit well by them. The good fits and characteristic curves of D-A equation provided evidence that a pore-filling phenomenon was involved during the adsorption of TCE and benzene onto NDA-201. Moreover, thermodynamic properties such as the Henry's constant and the isosteric enthalpy of adsorption were calculated. The isosteric enthalpy curves varied with the surface loading for each adsorbate, indicating that the hypercrosslinked polymeric resin has an energetically heterogeneous surface. In addition, a simple mathematic model developed by Yoon and Nelson was applied to investigate the breakthrough behavior on a hypercrosslinked polymeric resin column at 303 K and the calculated breakthrough curves were in high agreement with corresponding experimental data.

Adsorption of trichloroethylene and benzene vapors onto hypercrosslinked polymeric resin

International Nuclear Information System (INIS)

Liu Peng; Long Chao; Li Qifen; Qian Hongming; Li Aimin; Zhang Quanxing

2009-01-01

In this research, the adsorption equilibria of trichloroethylene (TCE) and benzene vapors onto hypercrosslinked polymeric resin (NDA201) were investigated by the column adsorption method in the temperature range from 303 to 333 K and pressures up to 8 kPa for TCE, 12 kPa for benzene. The Toth and Dubinin-Astakov (D-A) equations were tested to correlate experimental isotherms, and the experimental data were found to fit well by them. The good fits and characteristic curves of D-A equation provided evidence that a pore-filling phenomenon was involved during the adsorption of TCE and benzene onto NDA-201. Moreover, thermodynamic properties such as the Henry's constant and the isosteric enthalpy of adsorption were calculated. The isosteric enthalpy curves varied with the surface loading for each adsorbate, indicating that the hypercrosslinked polymeric resin has an energetically heterogeneous surface. In addition, a simple mathematic model developed by Yoon and Nelson was applied to investigate the breakthrough behavior on a hypercrosslinked polymeric resin column at 303 K and the calculated breakthrough curves were in high agreement with corresponding experimental data.

A comparative study for adsorption of lysozyme from aqueous samples onto Fe3O4 magnetic nanoparticles using different ionic liquids as modifier.

Science.gov (United States)

Kamran, Sedigheh; Absalan, Ghodratollah; Asadi, Mozaffar

2015-12-01

In this paper, nanoparticles of Fe3O4 as well as their modified forms with different ionic liquids (IL-Fe3O4) were prepared and used for adsorption of lysozyme. The mean size and the surface morphology of the nanoparticles were characterized by TEM, XRD and FTIR techniques. Adsorption studies of lysozyme were performed under different experimental conditions in batch system on different modified magnetic nanoparticles such as, lysozyme concentration, pH of the solution, and contact time. Experimental results were obtained under the optimum operational conditions of pH 9.0 and a contact time of 10 min when initial protein concentrations of 0.05-2.0 mg mL(-1) were used. The isotherm evaluations revealed that the Langmuir model attained better fits to the equilibrium data than the Freundlich model. The maximum obtained adsorption capacities were 370.4, 400.0 500.0 and 526.3 mg of lysozyme for adsorption onto Fe3O4 and modified magnetic nanoparticles by [C4MIM][Br], [C6MIM][Br] and [C8MIM][Br] per gram of adsorbent, respectively. The Langmuir adsorption constants were 0.004, 0.019, 0.024 and 0.012 L mg(-1) for adsorptions of lysozyme onto Fe3O4 and modified magnetic nanoparticles by [C4MIM][Br], [C6MIM][Br] and [C8MIM][Br], respectively. The adsorption capacity of lysozyme was found to be dependent on its chemical structure, pH of the solution, temperature and type of ionic liquid as modifier. The applicability of two kinetic models including pseudo-first order and pseudo-second order model was estimated. Furthermore, the thermodynamic parameters were calculated. Protein could desorb from IL-Fe3O4 nanoparticles by using NaCl solution at pH 9.5 and was reused.

Copper adsorption on magnetite-loaded chitosan microspheres: A kinetic and equilibrium study

Energy Technology Data Exchange (ETDEWEB)

Podzus, P.E., E-mail: ppodzus@gmail.com [Grupo de Aplicaciones de Materiales Biocompatibles, Departamento de Quimica, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, C1063ACV Buenos Aires (Argentina); Debandi, M.V. [Grupo de Aplicaciones de Materiales Biocompatibles, Departamento de Quimica, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, C1063ACV Buenos Aires (Argentina); Daraio, M.E., E-mail: medit@fi.uba.ar [Grupo de Aplicaciones de Materiales Biocompatibles, Departamento de Quimica, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, C1063ACV Buenos Aires (Argentina)

2012-08-15

A composite of Fe{sub 3}O{sub 4} nanoparticles and the biopolymer chitosan, chemically crosslinked, was prepared as microspheres and used to adsorb copper ions, which were chosen as a model of contaminant metal in water. The adsorption of copper on the magnetic microspheres was studied in a batch process, with different aqueous solutions of Cu (II) at concentrations ranging from 40 to 1100 ppm. Kinetic and equilibrium aspects of the adsorption process were studied. The time-dependent Cu (II) adsorption data were well described by a pseudo-second-order kinetic model. It was found that the equilibrium data follow the Langmuir isotherm, with a maximum adsorption capacity of around 500 mg Cu/g chitosan. The used microspheres were removed and after desorption the material was able to be reused as an adsorbent. The prepared microspheres proved efficient in the removal of copper ions through an adsorption process whose kinetic and equilibrium characteristics were analyzed.

Copper adsorption on magnetite-loaded chitosan microspheres: A kinetic and equilibrium study

International Nuclear Information System (INIS)

Podzus, P.E.; Debandi, M.V.; Daraio, M.E.

2012-01-01

A composite of Fe 3 O 4 nanoparticles and the biopolymer chitosan, chemically crosslinked, was prepared as microspheres and used to adsorb copper ions, which were chosen as a model of contaminant metal in water. The adsorption of copper on the magnetic microspheres was studied in a batch process, with different aqueous solutions of Cu (II) at concentrations ranging from 40 to 1100 ppm. Kinetic and equilibrium aspects of the adsorption process were studied. The time-dependent Cu (II) adsorption data were well described by a pseudo-second-order kinetic model. It was found that the equilibrium data follow the Langmuir isotherm, with a maximum adsorption capacity of around 500 mg Cu/g chitosan. The used microspheres were removed and after desorption the material was able to be reused as an adsorbent. The prepared microspheres proved efficient in the removal of copper ions through an adsorption process whose kinetic and equilibrium characteristics were analyzed.

Adsorption Characteristics of Water and Silica Gel System for Desalination Cycle

KAUST Repository

Cevallos, Oscar R.

2012-07-01

An adsorbent suitable for adsorption desalination cycles is essentially characterized by a hydrophilic and porous structure with high surface area where water molecules are adsorbed via hydrogen bonding mechanism. Silica gel type A++ possesses the highest surface area and exhibits the highest equilibrium uptake from all the silica gels available in the market, therefore being suitable for water desalination cycles; where adsorbent’s adsorption characteristics and water vapor uptake capacity are key parameters in the compactness of the system; translated as feasibility of water desalination through adsorption technologies. The adsorption characteristics of water vapor onto silica gel type A++ over a temperature range of 30 oC to 60 oC are investigated in this research. This is done using water vapor adsorption analyzer utilizing a constant volume and variable pressure method, namely the Hydrosorb-1000 instrument by Quantachrome. The experimental uptake data is studied using numerous isotherm models, i. e. the Langmuir, Tóth, generalized Dubinin-Astakhov (D-A), Dubinin-Astakhov based on pore size distribution (PSD) and Dubinin-Serpinski (D-Se) isotherm for the whole pressure range, and for a pressure range below 10 kPa, proper for desalination cycles; isotherms type V of the International Union of Pure and Applied Chemistry (IUPAC) classification were exhibited. It is observed that the D-A based on PSD and the D-Se isotherm models describe the best fitting of the experimental uptake data for desalination cycles within a regression error of 2% and 6% respectively. All isotherm models, except the D-A based on PSD, have failed to describe the obtained experimental uptake data; an empirical isotherm model is proposed by observing the behavior of Tóth and D-A isotherm models. The new empirical model describes the water adsorption onto silica gel type A++ within a regression error of 3%. This will aid to describe the advantages of silica gel type A++ for the design of

Adsorption separation of carbon dioxide from flue gas by a molecularly imprinted adsorbent.

Science.gov (United States)

Zhao, Yi; Shen, Yanmei; Ma, Guoyi; Hao, Rongjie

2014-01-01

CO2 separation by molecularly imprinted adsorbent from coal-fired flue gas after desulfurization system has been studied. The adsorbent was synthesized by molecular imprinted technique, using ethanedioic acid, acrylamide, and ethylene glycol dimethacrylate as the template, functional monomer, and cross-linker, respectively. According to the conditions of coal-fired flue gas, the influencing factors, including adsorption temperature, desorption temperature, gas flow rate, and concentrations of CO2, H2O, O2, SO2, and NO, were studied by fixed bed breakthrough experiments. The experimental conditions were optimized to gain the best adsorption performance and reduce unnecessary energy consumption in future practical use. The optimized adsorption temperature, desorption temperature, concentrations of CO2, and gas flow rate are 60 °C, 80 °C, 13%, and 170 mL/min, respectively, which correspond to conditions of practical flue gases to the most extent. The CO2 adsorption performance was nearly unaffected by H2O, O2, and NO in the flue gas, and was promoted by SO2 within the emission limit stipulated in the Chinese emission standards of air pollutants for a thermal power plant. The maximum CO2 adsorption capacity, 0.57 mmol/g, was obtained under the optimized experimental conditions, and the SO2 concentration was 150 mg/m(3). The influence mechanisms of H2O, O2, SO2, and NO on CO2 adsorption capacity were investigated by infrared spectroscopic analysis.

A one-dimensional stochastic approach to the study of cyclic voltammetry with adsorption effects

Energy Technology Data Exchange (ETDEWEB)

Samin, Adib J. [The Department of Mechanical and Aerospace Engineering, The Ohio State University, 201 W 19" t" h Avenue, Columbus, Ohio 43210 (United States)

2016-05-15