Remote Excavation System technology evaluation report: Buried Waste Robotics Program

International Nuclear Information System (INIS)

1993-09-01

This document describes the results from the Remote Excavation System demonstration and testing conducted at the Idaho National Engineering Laboratory during June and July 1993. The purpose of the demonstration was to ascertain the feasibility of the system for skimming soil and removing various types of buried waste in a safe manner and within all regulatory requirements, and to compare the performances of manual and remote operation of a backhoe. The procedures and goals of the demonstration were previously defined in The Remote Excavation System Test Plan, which served as a guideline for evaluating the various components of the system and discussed the procedures used to conduct the tests

Research on Trajectory Planning and Autodig of Hydraulic Excavator

Directory of Open Access Journals (Sweden)

Bin Zhang

2017-01-01

Full Text Available As the advances in computer control technology keep emerging, robotic hydraulic excavator becomes imperative. It can improve excavation accuracy and greatly reduce the operator’s labor intensity. The 12-ton backhoe bucket excavator has been utilized in this research work where this type of excavator is commonly used in engineering work. The kinematics model of operation device (boom, arm, bucket, and swing in excavator is established in both Denavit-Hartenberg coordinates for easy programming and geometric space for avoiding blind spot. The control approach is based on trajectory tracing method with displacements and velocities feedbacks. The trajectory planning and autodig program is written by Visual C++. By setting the bucket teeth’s trajectory, the program can automatically plan the velocity and acceleration of each hydraulic cylinder and motor. The results are displayed through a 3D entity simulation environment which can present real-time movements of excavator kinematics. Object-Oriented Graphics Rendering Engine and skeletal animation are used to give accurate parametric control and feedback. The simulation result shows that a stable linear autodig can be achieved. The errors between trajectory planning command and simulation model are analyzed.

OPTIMIZING UPPER EXCAVATOR

Directory of Open Access Journals (Sweden)

Dragos Vasile VÎGA

2016-05-01

Full Text Available An essential element when establishing the balance of a bucket wheel excavator is the determination of the barycentre, the best results being thus obtained by weighting after having installed all the components. The lack of correct balance for bucket wheel excavators determines their operation in an inadequate dynamic mode, or in extreme cases, there is the danger of losing stability by tilting over the excavator respectively suffering huge material and human loss. It is compulsory to verify for the correctness of the position and mass value of balance because there might be substantial error sources leading to compromise the operation. One of the most popular methods is that of weighting the entire equipment from the superior platform of the excavator. The weighting process implies the lifting of the excavators in three spots with hydraulic cylinders, the measurement of the forces, as well as the measurement of pressure inside the cylinders and of the stroke of each cylinder. The data measurement and rehashing installation is destined to determine the dimensions that finally define the weighting process of excavators or other operating machineries to which the balancing and control of stability is imposed.

Excavating and loading equipment for peat mining

Science.gov (United States)

Mikhailov, A. V.; Zhigulskaya, A. I.; Yakonovskaya, T. B.

2017-10-01

Recently, the issues of sustainable development of Russian regions, related to ensuring energy security, are more urgent than ever. To achieve sustainable development, an integrated approach to the use of local natural resources is needed. Practically in all north regions of the Russian Federation, peat as a local natural resource is widespread, which has a practical application in the area of housing services. The paper presents the evaluation of technologies for open-pit peat mining, as well as analysis of technological equipment for peat production. Special attention is paid to a question of peat materials excavating and loading. The problem of equipment selection in a peat surface mine is complex. Many features, restrictions and criteria need to be considered. Use of low and ultra-low ground pressure excavators and low ground pressure front-end loaders with full-range tires to provide the necessary floatation in the peat bog environment is offered.

Principles of Mechanical Excavation

International Nuclear Information System (INIS)

Lislerud, A.

1997-12-01

Mechanical excavation of rock today includes several methods such as tunnel boring, raiseboring, roadheading and various continuous mining systems. Of these raiseboring is one potential technique for excavating shafts in the repository for spent nuclear fuel and dry blind boring is promising technique for excavation of deposition holes, as demonstrated in the Research Tunnel at Olkiluoto. In addition, there is potential for use of other mechanical excavation techniques in different parts of the repository. One of the main objectives of this study was to analyze the factors which affect the feasibility of mechanical rock excavation in hard rock conditions and to enhance the understanding of factors which affect rock cutting so as to provide an improved basis for excavator performance prediction modeling. The study included the following four main topics: (a) phenomenological model based on similarity analysis for roller disk cutting, (b) rock mass properties which affect rock cuttability and tool life, (c) principles for linear and field cutting tests and performance prediction modeling and (d) cutter head lacing design procedures and principles. As a conclusion of this study, a test rig was constructed, field tests were planned and started up. The results of the study can be used to improve the performance prediction models used to assess the feasibility of different mechanical excavation techniques at various repository investigation sites. (orig.)

Principles of Mechanical Excavation

Energy Technology Data Exchange (ETDEWEB)

Lislerud, A. [Tamrock Corp., Tampere (Finland)

1997-12-01

Mechanical excavation of rock today includes several methods such as tunnel boring, raiseboring, roadheading and various continuous mining systems. Of these raiseboring is one potential technique for excavating shafts in the repository for spent nuclear fuel and dry blind boring is promising technique for excavation of deposition holes, as demonstrated in the Research Tunnel at Olkiluoto. In addition, there is potential for use of other mechanical excavation techniques in different parts of the repository. One of the main objectives of this study was to analyze the factors which affect the feasibility of mechanical rock excavation in hard rock conditions and to enhance the understanding of factors which affect rock cutting so as to provide an improved basis for excavator performance prediction modeling. The study included the following four main topics: (a) phenomenological model based on similarity analysis for roller disk cutting, (b) rock mass properties which affect rock cuttability and tool life, (c) principles for linear and field cutting tests and performance prediction modeling and (d) cutter head lacing design procedures and principles. As a conclusion of this study, a test rig was constructed, field tests were planned and started up. The results of the study can be used to improve the performance prediction models used to assess the feasibility of different mechanical excavation techniques at various repository investigation sites. (orig.). 21 refs.

Long-range terrain characterization for productive regolith excavation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The proposed research will develop long-range terrain characterization technologies for autonomous excavation in planetary environments. This work will develop a...

The Montana ALE (Autonomous Lunar Excavator) Systems Engineering Report

Science.gov (United States)

Hull, Bethanne J.

2012-01-01

On May 2 1-26, 20 12, the third annual NASA Lunabotics Mining Competition will be held at the Kennedy Space Center in Florida. This event brings together student teams from universities around the world to compete in an engineering challenge. Each team must design, build and operate a robotic excavator that can collect artificial lunar soil and deposit it at a target location. Montana State University, Bozeman, is one of the institutions selected to field a team this year. This paper will summarize the goals of MSU's lunar excavator project, known as the Autonomous Lunar Explorer (ALE), along with the engineering process that the MSU team is using to fulfill these goals, according to NASA's systems engineering guidelines.

Safety excavation; Seguranca em escavacoes

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Walter Manoel [TRANSPETRO - PETROBRAS Transporte S.A., Rio de Janeiro, RJ (Brazil)

2003-07-01

In the construction and maintenance services of buried pipelines, the excavation is the activity that contains larger risk, could cause serious accidents. Norms, procedures and technical articles, national and international goods, should be followed for legal and technical aspects. This paper - Safety in Excavations - has purpose to gather all the technical concepts and of safety in a document denominated Procedure of Safety Excavation, serving as instrument to systematize and control the execution of excavation services in construction civil, assembly and pipelines repairs, seeking the people, facilities and the environment's safety. (author)

A remotely operated excavator [HAZ-TRAK

International Nuclear Information System (INIS)

Anon.

1992-01-01

HAZ-TRAK is a remotely operated excavator and material handling system for nuclear waste site characterization, waste site remediation, and the decommissioning of nuclear facilities. HAZ-TRAK combines the power and mobility of a commercial excavator, with the dexterity and controllability of a force feedback manipulator system: when operating HAZ-TRAK as an excavator, the operator can feel buried objects. A master/slave control method enables the operator to intuitively control all the excavator arm functions with one hand. The main features of the excavator are described in this article. (author)

Lightweight Bulldozer Attachment for Construction and Excavation on the Lunar Surface

Science.gov (United States)

Mueller, Robert; Wilkinson, R. Allen; Gallo, Christopher A.; Nick, Andrew J.; Schuler, Jason M.; King, Robert H.

2009-01-01

A lightweight bulldozer blade prototype has been designed and built to be used as an excavation implement in conjunction with the NASA Chariot lunar mobility platform prototype. The combined system was then used in a variety of field tests in order to characterize structural loads, excavation performance and learn about the operational behavior of lunar excavation in geotechnical lunar simulants. The purpose of this effort was to evaluate the feasibility of lunar excavation for site preparation at a planned NASA lunar outpost. Once the feasibility has been determined then the technology will become available as a candidate element in the NASA Lunar Surface Systems Architecture. In addition to NASA experimental testing of the LANCE blade, NASA engineers completed analytical work on the expected draft forces using classical soil mechanics methods. The Colorado School of Mines (CSM) team utilized finite element analysis (FEA) to study the interaction between the cutting edge of the LANCE blade and the surface of soil. FEA was also used to examine various load cases and their effect on the lightweight structure of the LANCE blade. Overall it has been determined that a lunar bulldozer blade is a viable technology for lunar outpost site preparation, but further work is required to characterize the behavior in 1/6th G and actual lunar regolith in a vacuum lunar environment.

Choice of rock excavation methods for the Swedish deep repository for spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Baeckblom, Goeran [Conrox, Stockholm (Sweden); Christiansson, Rolf [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Lagerstedt, Leif [SwedPower AB, Stockholm (Sweden)

2004-09-01

Choice of rock excavation methods will or may have implications for a number of issues like repository layout, long term and operational safety, environmental impact, design of and operation of transport vehicles and methodology for backfilling the repository before closure as well as effects on costs and schedules. To fully analyse the issues at hand related to selection of excavation methods, SKB organized a project with the objectives: To investigate and compare principal technical solutions for rock excavation, both methods that are used at present but also methods that may be feasible 10 years from now; To assess how the selection of excavation method influences the design and operation of the deep repository; To present a definition of the Excavation Damaged/Disturbed Zone and practical methods for measurements of EDZ; To present advantages and disadvantages with different excavation methods for the various tunnels and underground openings as a basis for selection of preferred excavation methods; To present the Design Justification Statement for the selection of particular excavation methods for the different tunnels and openings in the deep repository to underpin a decision on excavation method; and To present background data that may be required for the evaluation of the long term safety of the deep repository. Main alternatives studied are very smooth blasting, excavation with a tunnel-boring machine (TBM) and excavation with horizontal pull-reaming using more or less conventional raise-boring equipment. The detailed studies were carried through in co-operation with major suppliers and end-users of the technology. An observation in this study is that all excavation technologies are mature; no major breakthroughs are foreseen within a 10 year period but it is likely that for any technology selected, SKB would specifically fine-tune the design of the equipment and work procedures in view of requirements and site specific conditions. Excavation methods have

Choice of rock excavation methods for the Swedish deep repository for spent nuclear fuel

International Nuclear Information System (INIS)

Baeckblom, Goeran; Christiansson, Rolf; Lagerstedt, Leif

2004-09-01

Choice of rock excavation methods will or may have implications for a number of issues like repository layout, long term and operational safety, environmental impact, design of and operation of transport vehicles and methodology for backfilling the repository before closure as well as effects on costs and schedules. To fully analyse the issues at hand related to selection of excavation methods, SKB organized a project with the objectives: To investigate and compare principal technical solutions for rock excavation, both methods that are used at present but also methods that may be feasible 10 years from now; To assess how the selection of excavation method influences the design and operation of the deep repository; To present a definition of the Excavation Damaged/Disturbed Zone and practical methods for measurements of EDZ; To present advantages and disadvantages with different excavation methods for the various tunnels and underground openings as a basis for selection of preferred excavation methods; To present the Design Justification Statement for the selection of particular excavation methods for the different tunnels and openings in the deep repository to underpin a decision on excavation method; and To present background data that may be required for the evaluation of the long term safety of the deep repository. Main alternatives studied are very smooth blasting, excavation with a tunnel-boring machine (TBM) and excavation with horizontal pull-reaming using more or less conventional raise-boring equipment. The detailed studies were carried through in co-operation with major suppliers and end-users of the technology. An observation in this study is that all excavation technologies are mature; no major breakthroughs are foreseen within a 10 year period but it is likely that for any technology selected, SKB would specifically fine-tune the design of the equipment and work procedures in view of requirements and site specific conditions. Excavation methods have

Exploration and excavation of shipwrecks in Goa and adjoining waters 2004-2005

Digital Repository Service at National Institute of Oceanography (India)

Anon

As a part of the Institutional Project, 'Application of geological and geophysical methods in marine archaeology and underwater explorations' (STS 0004), exploration and excavation of shipwrecks have been carried out from Nov 24-Dec 02, 2005 for 06...

Exploration and excavation of shipwrecks in Goa and adjoining waters 2005-2006

Digital Repository Service at National Institute of Oceanography (India)

As a part of the institutional project, 'Application of Geological and Geophysical methods in Marine Archaeology and Underwater Explorations, (OLP 0008)', exploration and excavation of shipwrecks have been carried out from 23 Jan 2006 to 21 Feb 2006...

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

Energy Technology Data Exchange (ETDEWEB)

Massmann, Jobst

2009-07-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation induced

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

International Nuclear Information System (INIS)

Massmann, Jobst

2009-01-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation induced

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

Energy Technology Data Exchange (ETDEWEB)

Massmann, Jobst

2009-07-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation

Performance prediction of mechanical excavators from linear cutter tests on Yucca Mountain welded tuffs

International Nuclear Information System (INIS)

Gertsch, R.; Ozdemir, L.

1992-09-01

The performances of mechanical excavators are predicted for excavations in welded tuff. Emphasis is given to tunnel boring machine evaluations based on linear cutting machine test data obtained on samples of Topopah Spring welded tuff. The tests involve measurement of forces as cutters are applied to the rock surface at certain spacing and penetrations. Two disc and two point-attack cutters representing currently available technology are thus evaluated. The performance predictions based on these direct experimental measurements are believed to be more accurate than any previous values for mechanical excavation of welded tuff. The calculations of performance are predicated on minimizing the amount of energy required to excavate the welded tuff. Specific energy decreases with increasing spacing and penetration, and reaches its lowest at the widest spacing and deepest penetration used in this test program. Using the force, spacing, and penetration data from this experimental program, the thrust, torque, power, and rate of penetration are calculated for several types of mechanical excavators. The results of this study show that the candidate excavators will require higher torque and power than heretofore estimated

Lightweight Robotic Excavation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Robust, lightweight, power-efficient excavation robots are mission enablers for lunar outposts and surface systems. Lunar excavators of this type cost-effectively...

Excavation/Fill/Soil Disturbance, Self-Study #31419

Energy Technology Data Exchange (ETDEWEB)

Grogin, Phillip W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-02-06

This course, Excavation/Fill/Soil Disturbance Self-Study (#31419), presents an overview of the hazards, controls, and requirements that affect safe excavations at Los Alamos National Laboratory (LANL). An overview of the LANL excavation/fill/soil disturbance permit (EXID permit) approval process is also presented, along with potholing requirements for planning and performing excavations at LANL.

Effect of excavation method on rock mass displacement

International Nuclear Information System (INIS)

Sato, Toshinori; Kikuchi, Tadashi; Sugihara, Kozo

1998-01-01

Rock mass displacement measurements have been performed to understand rock mass behavior and its dependence on excavation method during drift excavation at the Tono mine. Rock mass displacements of 1.46 mm and 0.67 mm have been measured at one meter (0.33D: blasting, 0.42D: machine, D: width of drift) from the walls of drifts excavated by the drill and blasting method and machine, respectively. Numerical analysis of rock mass displacements with Finite Element Method has been performed assuming an excavation disturbed zone. Measured and analysed rock mass displacements are consistent with each other for the drift excavation by the drill and blasting method. The excavation disturbed zone was narrower for the drift excavated by machine than for the drift excavated by the drill and blasting method. (author)

The essence of excavators

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

Competition is hotting-up between rope shovel and hydraulic excavator manufacturers as demand mounts for surface loading equipment. The article gives an overview of major players and gives details of their popular models of excavators and rope shovels. It compares surface loading equipment from P & H, Bucyrus, THYI, OMZ, Komatsu, Hirachi, O & K and Liebherr. 4 tabs., 3 photos.

Excavating wide inclines in weak strata

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, N N [Ukrspetsstroiproekt (USSR)

1990-09-01

Discusses schemes for excavation of transport inclines in surface mines under conditions of weak, unstable rocks characterized by a high water content. The schemes are aimed at maximum reduction of excavation operations without infringing the safety of personnel. Use of walking draglines (the EhSh-20/90, EhSh-100/100 and EhSh-10/70) is evaluated. Optimum schemes for incline excavation and determining optimum slope inclination are described on the example of the Berezovsk brown coal surface mine in the USSR. Efficiency of optimum schemes is analyzed: range of excavation, safety degree, landslide hazards, water influx rate, accident rate, etc.

Customized excavators beat the odds

Energy Technology Data Exchange (ETDEWEB)

1991-10-01

Blackstone Mining, launched in 1983, is based in eastern Ohio, near Cadiz and specializes in stripping small properties for Ohio Edison. Specially modified hydraulic excavators and an efficient mining technique allow the mining of marginal coal deposits. In 1986 Ken McBeth, the company's founder begun using a Cat 245 hydraulic excavator to cleanly and efficiently load coal and also remove overburden. Modifications include: a mass excavator boom 5 feet longer to better reach over the sides of haul trucks and load from higher benches; and larger hydraulic cylinders to maintain earthmoving production. McBeth also devised a fast economical technique for extracting coal from the thin, narrow seams. Soft cover material is removed by excavator; the remaining sand and limestone are blasted to within 2 feet of the seam; the remaining material is removed by an agricultural tractor with a blade; an excavator loads the coal into haul trucks starting at the toe of the face and working backwards. Haul trucks are not placed directly on the seam. This prevents contamination, reducing the price of the coal. There is no wash plant; the coal is hauled direct to the utility. 4 photos.

GPS-Based Excavation Encroachment Notification

Science.gov (United States)

2011-10-31

Excavation damage is the primary threat to the integrity of the natural gas distribution system. According to the Common Ground Alliance, the two primary root causes of excavation damage are failure to notify the one-call center and careless excavati...

Mechanical tunnel excavation in welded tuff

International Nuclear Information System (INIS)

Sperry, P.E.

1991-01-01

The Technical Review Board for the US high-level radioactive waste facility at Yucca Mountain has recommended maximum use of open-quotes the most modern mechanical excavation techniques...in order to reduce disturbance to the rock walls and to achieve greater economy of time and cost.close quotes Tunnels for the waste repository at Yucca Mountain can be economically constructed with mechanical excavation equipment. This paper presents the results of mechanical excavation of a tunnel in welded tuff, similar to the tuffs of Yucca Mountain. These results are projected to excavation of emplacement drifts in Yucca Mountain using a current state-of-the-art tunnel boring machine (TBM)

ROCK MASS DAMAGED ZONE CAUSED BY BLASTING DURING TUNNEL EXCAVATION

Directory of Open Access Journals (Sweden)

Hrvoje Antičević

2012-07-01

Full Text Available Design of underground spaces, including tunnels, and repositories for radioactive waste include the application of the same or similar technologies. Tunnel excavation by blasting inevitably results in the damage in the rock mass around the excavation profile. The damage in the rock mass immediately next to the tunnel profile emerges as the expanding of the existing cracks and the appearance of new cracks, i.e. as the change of the physical and-mechanical properties of the rock mass. Concerning the design of deep geological repositories, requirements in terms of damaged rock are the same or more rigorous than for the design of tunnel. The aforementioned research is directed towards determining the depth of damage zone caused by blasting. The depth of the damage zone is determined by measuring the changes of physical and-mechanical properties of the rock mass around the tunnel excavation profile. By this research the drilling and blasting parameters were correlated with the depth and size of the damage zone (the paper is published in Croatian.

AECL's excavation stability study - summary of observations

International Nuclear Information System (INIS)

Read, R.S.; Chandler, N.A.

1996-05-01

The Excavation Stability Study (ESS) was conducted at the 420 Level of the Underground Research Laboratory (URL) to evaluate stability and the extent of excavation damage in tunnels as a function of tunnel geometry and orientation, geology, and excavation method. A series of ovaloid and circular openings were used to achieve different boundary stress levels and near-field stress distributions to assess the effect of tunnel geometry on damage development. Several of these openings had sections in both granite and granodiorite lithology, providing a comparison of damage in rock types with different strength characteristics. Damage around circular tunnels (one excavated by drill-and-blast, the other by mechanical means) was also investigated. The study.showed that mechanically stable openings can be excavated in the most adverse stress conditions at the 420 Level of the URL. In addition, it was shown that tunnel stability is sensitive to tunnel shape, variations in geology, and to some extent, the excavation method. Findings of the study are relevant in developing design criteria, and in assessing the feasibility of constructing large ovaloid openings in adverse stress conditions. This report summarizes the preliminary observations related to tunnel stability and excavation damage. (author). 8 refs., 7 tabs., 23 figs

Feature Extraction for Digging Operation of Excavator Based on Data-Driven Skill-Based PID Controller

Directory of Open Access Journals (Sweden)

Kazushige Koiwai

2017-11-01

Full Text Available Improvement of the work efficiency is demanded by aging and reducing of the working population in the construction field, so that some automation technologies are applied to construction equipment, such as bulldozers and excavators. However, not only the automation technologies but also expert skills are necessary to improve the work efficiency. In this paper, the human skill evaluation is proposed by the data-driven skill-based PID controller. The proposed method is applied to the excavator digging operation. As the result, the difference between the novice operation and the skilled operation is extracted. Moreover, the numerical difference is clarified based on the result.

End effectors and attachments for buried waste excavation equipment

International Nuclear Information System (INIS)

King, R.H.

1993-09-01

The Buried Waste Integrated Demonstration (BWID) supports the applied research, development, demonstration, and evaluation of a suite of advanced technologies that form a comprehensive remediation system for the effective and efficient remediation of buried waste. Their efforts are identified and coordinated in support of the U.S. Department of Energy (DOE), Environmental Restoration and Waste Management (ER ampersand WM) Department's needs and objectives. The present focus of BWID is to support retrieval and ex-situ treatment configuration options. Future activities will explore and support containment, and stabilization efforts in addition to the retrieval/ex situ treatment options. This report presents a literature search on the state-of-the-art in end effectors and attachments in support of excavator of buried transuranic waste. Included in the report are excavator platforms and a discussion of the various attachments. Also included is it list of vendors and specifications

The underground research laboratory room 209 excavation response test

International Nuclear Information System (INIS)

Simmons, G.R.

1992-02-01

The response of the rock mass to excavation is an important factor in the design and performance of underground excavations and installations. This is particularly true in the excavation of vaults for the disposal of nuclear fuel waste, where the conditions in the rock mass around the disposal areas may affect the performance of engineered sealing systems installed to isolate the waste. The factors influencing, and mechanisms controlling, rock mass response to excavation must be understood in order to accommodate excavation response effects in disposal vault design and construction

Overview of the excavation disturbance experiment at the Kamaishi mine

International Nuclear Information System (INIS)

Matsui, Hiroya; Sato, Toshinori; Sugihara, Kozo; Kikuchi, Tadashi

1999-01-01

Excavation of an underground drift disturbs the rock mass around the opening by each of the following processes: Fracturing in the vicinity of opening induced by the excavation work and stress concentration. Changes in the apertures of existing fractures due to stress redistribution. Changes in water pressure around the opening due to water inflow and chemical changes due to the increased oxygen supply to the rock and such phenomena as degassing of groundwater. All of these mechanical, hydrological, and chemical changes to the rock mass are termed excavation disturbance and the affected area is called the 'Excavation Disturbed Zone (EDZ)'. The portion of the EDZ in which the rock mass is fractured due to excavation is called the Excavation Damaged Zone'. This experiment is focused on the mechanical and hydrological property changes caused by excavation, the degree and extend of which is important for the design, excavation and support of underground openings. The relevance of the EDZ for the geological isolation of nuclear waste disposal may be summarized as: 1) Relevance to near-field performance assessment. The EDZ is of importance for near-field performance assessment, as the development of new fractures and the opening of existing fractures due to excavation may create preferential pathways for mass transport from the engineered barrier system to natural transmissive flowpaths. 2) Relevance to the design, excavation and sealing of a repository. The excavation method affects the properties and the extend of the excavation damaged zone. The shape and the scale of the underground opening, and whether the underground opening is backfilled after excavation, will affect the final stress state. It is important to understand the EDZ for the design, excavation and sealing of a repository. 3) Initial and boundary conditions of in situ experiments. Information about the EDZ is necessary for the design and interpretation of certain in situ experiments. (author)

FROM EXCAVATIONS TO WEB: A GIS FOR ARCHAEOLOGY

Directory of Open Access Journals (Sweden)

M. G. D'Urso

2017-05-01

Full Text Available The study and the protection of Cultural Heritage in recent years have undergone a revolution about the search tools and the reference disciplines. The technological approach to the problem of the collection, organization and publication of archaeological data using GIS software has completely changed the essence of the traditional methods of investigation, paving the way to the development of several application areas, up to the Cultural Resource Management. A relatively recent specific sector of development for archaeological GIS development sector is dedicated to the intra - site analyses aimed to recording, processing and display information obtained during the excavations. The case - study of the archaeological site located in the south - east of San Pietro Vetere plateau in Aquino, in the Southern Lazio, is concerned with the illustration of a procedure describing the complete digital workflow relative to an intra-site analysis of an archaeological dig. The GIS project implementation and its publication on the web, thanks to several softwares, particularly the FOSS (Free Open Source Software Quantum - GIS, are an opportunity to reflect on the strengths and the critical nature of this particular application of the GIS technology. For future developments in research it is of fundamental importance the identification of a digital protocol for processing of excavations (from the acquisition, cataloguing, up data insertion, also on account of a possible future Open Project on medieval Aquino.

Аsymmetry of Structural Institutional and Technological Changes in Economy

Directory of Open Access Journals (Sweden)

Katkovа Marina Andreevna

2014-12-01

Full Text Available The article is devoted to the research on interrelation between institutional and technological changes. The authors provide the convincing argument in favor of the thesis on asymmetry of structural, institutional and technological changes. The complex of analytic methods is used in the work – comparative statics, static analysis, dynamic analysis. The analysis results in the conclusion on strengthening the heterogeneity, instability and uncertainty of the social and economic phenomena and processes. The authors comprehend structural changes as the changes in ratios and proportions of economic structure. They point to the emergence of new integrated characteristics and describe the synergetic effect of the general development. The use of the theory of technological modes allowed allocating radical and local shifts. The particular emphasis is placed on the analysis of reversible and irreversible structural and technological shifts as a special form of structural and technological changes. The application of the method of institutional statics and dynamics is effective in the analysis of technological and institutional symmetry / asymmetry. The emergence of negative institutional changes is explained by insufficient, inadequate or fragmentary assimilation of market institutes. The institutes interfering the innovative development stand against the institutes of innovative development. The institutional traps of structural and technological transformations are subdivided by authors into the traps of micro- and macrolevel. The authors point to the difficulty of assessing the institutes of microlevel by means of statistical data. They suggest using the phenomena which are under the control of authorities and subject to regulation as indicators. To define the opportunities of institutional management and the borders of government intervention the authors investigate in detail the institutional traps. They include moral and psychological unreadiness

Characterization of the emissions impacts of hybrid excavators with a portable emissions measurement system (PEMS)-based methodology.

Science.gov (United States)

Cao, Tanfeng; Russell, Robert L; Durbin, Thomas D; Cocker, David R; Burnette, Andrew; Calavita, Joseph; Maldonado, Hector; Johnson, Kent C

2018-04-13

Hybrid engine technology is a potentially important strategy for reduction of tailpipe greenhouse gas (GHG) emissions and other pollutants that is now being implemented for off-road construction equipment. The goal of this study was to evaluate the emissions and fuel consumption impacts of electric-hybrid excavators using a Portable Emissions Measurement System (PEMS)-based methodology. In this study, three hybrid and four conventional excavators were studied for both real world activity patterns and tailpipe emissions. Activity data was obtained using engine control module (ECM) and global positioning system (GPS) logged data, coupled with interviews, historical records, and video. This activity data was used to develop a test cycle with seven modes representing different types of excavator work. Emissions data were collected over this test cycle using a PEMS. The results indicated the HB215 hybrid excavator provided a significant reduction in tailpipe carbon dioxide (CO 2 ) emissions (from -13 to -26%), but increased diesel particulate matter (PM) (+26 to +27%) when compared to a similar model conventional excavator over the same duty cycle. Copyright © 2018 Elsevier B.V. All rights reserved.

Heart rot hotel: fungal communities in red-cockaded woodpecker excavations

Science.gov (United States)

Michelle A. Jusino; Daniel L. Lindner; Mark T. Banik; Jeffrey R. Walters

2015-01-01

Tree-cavity excavators such as woodpeckers are ecosystem engineers that have potentially complex but poorly documented associations with wood decay fungi. Fungi facilitate cavity excavation by preparing and modifying excavation sites for cavity excavators. Associations between fungi and endangered red-cockaded woodpeckers (RCWs) are particularly interesting because...

Institutions, Technological Change and Economic Growth

Directory of Open Access Journals (Sweden)

David Corderí Novoa

2005-01-01

Full Text Available Theories of economic growth try to explain variations in per capita income across countries by differences in capital accumulation and productivity. However, many scholars consider that integrating institutions into economic theory and economic history is an essential step in improving explanations of why some societies are richer than others. This paper develops the empirical and theoretical case that differences in institutions are the fundamental cause of differences in technological change (productivity, hence in economic growth. First, I give a definition of institutions and how they influence economic performance, from a New Institutional Economics point of view. Then, I introduce the theoretical framework based on the economics of ideas and endogenous growth models. Finally, I argue that R&D expenditures -a proxy for technological change- will vary across countries depending on some measures of institutional quality. In the end, this paper finds that stronger institutions (measured by an aggregate of institutional quality encourage greater R&D expenditures. At a disaggregate level, the rule of law is positively correlated and the regulatory burden is negatively correlated with R&D expenditures. Human capital level (measured by the tertiary and primary school enrolment rates has also a significant positive impact in R&D expenditures.

Summary report of soil removal preliminary excavations

International Nuclear Information System (INIS)

Wickland, C.E.

1975-01-01

This report discusses a proposed technique to remove small areas, less than 2,000 m 2 , of contaminated soil and the results of an actual excavation. Based on the results of a trial excavation in uncontaminated soil and an excavation of two trenches in contaminated soil, it is concluded that the techniques described are a satisfactory means of contaminated soil removal. It can be done safely with a release of airborne plutonium a factor of 10 or more below the Environmental Protection Administration (EPA) limit

A Prototype Bucket Wheel Excavator for the Moon, Mars and Phobos

Science.gov (United States)

Muff, T.; Johnson, L.; King, R.; Duke, M. B.

2004-02-01

Excavation of surface regolith material is the first step in processes to extract volatile materials from planetary surface regolith for the production of propellant and life support consumables. Typically, concentrations of volatiles are low, so relatively large amounts of material must be excavated. A bucket wheel excavator is proposed, which has the capability of continuous excavation, which is readily adapted to granular regolith materials as found on the Moon, in drift deposits on Mars, and probably on the surface of asteroids and satellites, such as Phobos. The bucket wheel excavator is relatively simple, compared to machines such as front end loaders. It also has the advantage that excavation forces are principally horizontal rather than vertical, which minimizes the need for excavator mass and suits it to operations in reduced gravity fields. A prototype small bucket wheel excavator has been built at approximately the scale of the rovers that are carried to Mars on the Mars Exploration Rover Mission. The prototype allows the collection of data on forces exerted and power requirements for excavation and will provide data on which more efficient designs can be based. At excavation rates in the vicinity of one rover mass of material excavated per hour, tests of the prototype demonstrate that the power required is largely that needed to operate the excavator hardware and not related strongly to the amount of material excavated. This suggests that the excavation rate can be much larger for the same excavation system mass. Work on this prototype is continuing on the details of transfer of material from the bucket wheel to an internal conveyor mechanism, which testing demonstrated to be problematic in the current design.

Home and Away: The Use of Institutional and Non-Institutional Technologies to Support Learning and Teaching

Science.gov (United States)

Flavin, Michael

2016-01-01

This paper examines the usage of institutional and non-institutional technologies to support learning and teaching in UK higher education. Previous work on disruptive technology and disruptive innovation has argued that users prefer simple and convenient technologies, and often repurpose technologies from designers' intentions; this paper…

Study on dynamic behavior of a shaft excavation through a faulted crystalline rock mass

International Nuclear Information System (INIS)

Hashizume, Shigeru; Matsui, Hiroya; Horiuchi, Yasuharu; Hata, Koji; Akiyoshi, Kenji; Sato, Shin; Shibata, Chihoko; Niunoya, Sumio; Noda, Masaru

2013-01-01

The 'Mizunami Underground Research Laboratory' has been studying and developing engineering technology for deep underground applications. These applications are multifaceted and are categorized as development of design and construction planning technology, development construction technology, development of countermeasure technology, and development of technology for construction and operation security. In this report, the dynamic behavior of shaft and the surrounding rock mass has been studied with respect to rock mass displacement and stress, the effect of using a concrete liner and excavating through faulted crystalline rock. (author)

Nuclear Human Resource Development in Tokyo Institute of Technology

International Nuclear Information System (INIS)

Satio, Masaki; Igashira, Masayuki; Obara, Toru; Kikura, Hironari; Kawahara, Akira; Ujita, Hiroshi

2012-01-01

Nuclear engineering education has been initiated in 1957 at the graduate school of Tokyo Institute of Technology. Higher Educational activities have been conducted for more than half century. More than 1000 Master students and 200 Doctoral students graduated from the Department of Nuclear Engineering in Tokyo Institute if Technology. Many of them are working in nuclear industries and institutes. International course of nuclear engineering was initiated in 1994, and 130 students from 20 overseas countries have graduated from Master and Doctoral Programs. In the present paper, the current nuclear educational activities in Tokyo Institute of Technology are summarized

100 area excavation treatability test plan

International Nuclear Information System (INIS)

1993-05-01

This test plan documents the requirements for a treatability study on field radionuclide analysis and dust control techniques. These systems will be used during remedial actions involving excavation. The data from this treatability study will be used to support the feasibility study (FS) process. Development and screening of remedial alternatives for the 100 Area, using existing data, have been completed and are documented in the 100 Area Feasibility Study, Phases 1 and 2 (DOE-RL 1992a). Based on the results of the FS, the Treatability Study Program Plan (DOE-RL 1992b) identifies and prioritizes treatability studies for the 100 Area. The data from the treatability study program support future focused FS, interim remedial measures (IRM) selection, operable unit final remedy selection, remedial design, and remedial actions. Excavation is one of the high-priority, near-term, treatability study needs identified in the program plan (DOE-RL 1992b). Excavation of contaminated soils and buried solid wastes is included in several of the alternatives identified in the 100 Area FS. Although a common activity, excavation has only been used occasionally at the Hanford Site for waste removal applications

Development of excavator training simulator using leap motion controller

Science.gov (United States)

Fahmi, F.; Nainggolan, F.; Andayani, U.; Siregar, B.

2018-03-01

Excavator is a heavy machinery that is used for many industries purposes. Controlling the excavator is not easy. Its operator has to be trained well in many skills to make sure it is safe, effective, and efficient while using the excavator. In this research, we proposed a virtual reality excavator simulator supported by a device called Leap Motion Controller that supports finger and hand motions as an input. This prototype will be developed than in the virtual reality environment to give a more real sensing to the user.

The Origin of the ‘Chicago Method’ Excavation Techniques: Contributions of William Nickerson and Frederick Starr

Directory of Open Access Journals (Sweden)

David Browman

2013-09-01

Full Text Available What were the origins of the ‘Chicago method’ of scientific excavation? What is it and how did it get that name? Does its origin predate its popular employment at excavations in the USA during the 1930s and 1940s, and go back to institutional competition between Frederic Ward Putnam of the Field Museum and Frederick Starr of the University of Chicago? Or was it the result of the fieldwork of avocational archaeologist and one of Putnam’s first students, William Baker Nickerson, who implemented it as the basis of his fieldwork, and proved its efficacy, for many years before he retired in 1921? Nickerson’s detailed notes on the results of his thorough stratigraphic excavation techniques, used at many archaeological sites in Iowa, Illinois, Ohio and Minnesota, were passed on to the first University of Chicago field party doing archaeological work in Illinois, that consequently became the foundations of the later ‘Chicago method’.

The Application of Foundation Pit Monitoring Technology to the Excavation

Directory of Open Access Journals (Sweden)

Qiu Jin

2015-01-01

Full Text Available The foundation pit monitoring plays an important role in the foundation pit supporting projects especially in those deep foundation pit projects. Through the whole monitoring of the foundation pit construction from the excavation to the backfill, we can learn about the forcing and deforming process of the foundation pit supporting system, and grasp the impact of external condition changes on the foundation pit. This paper takes a project in Jinan as an example to establish a specific monitoring program, and then conducts the analysis and evaluation of the monitoring data; the real-time grasp of the foundation pit deformation and internal force changes can help to further ensure the security status of the foundation pit, thus better guiding the construction.

Indian Institute of Technology, Guwahat

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 10; Issue 1. Refresher Course in Experimental Physics – Indian Institute of Technology, ... Information and Announcements Volume 10 Issue 1 January 2005 pp 96-96 ...

Outline and results of study on excavation response of rock mass around shaft in shaft excavation effects project

International Nuclear Information System (INIS)

Sugihara, Kozo; Matsui, Hiroya; Sato, Toshinori

1993-01-01

A shaft, with a diameter of 6 m and a depth of 150 m, has been newly excavated in sedimentary rock and excavation response of rock mass around the shaft has been measured and analyzed. Excavation response has been evaluated based on the results of measurement of rock mass movement, such as displacement and strain, and change of rock property, such as deformability and permeability. This study indicates that rock property has been changed with in about 1 m from the shaft wall, and rock mass movement and property change has been influenced by rock facies, fracture and re-distributed stress. The relation between property change and these factors is remained to be evaluated in future study. (author)

Real-time support for precision excavation of radionuclide-contaminated soils

International Nuclear Information System (INIS)

Durham, L. A.; Johnson, R. L.

2003-01-01

Traditional approaches to excavation design for sites with radionuclide-contaminated soils generally involve work plans with fixed excavation footprints and post-excavation verification sampling. Recent advancements in real-time data collection systems, combined with data loggers, location control systems, and secure project-support Web sites, allow for an alternative, more precise approach to excavation design and implementation. In this mode, traditional work plans are replaced with dynamic work plans. Excavation efforts are organized by lift, with real-time dig face screening performed and the data for each lift analyzed, before excavation continues. Rather than specifying excavation footprints, dynamic work plans identify the decision logic that will be used to determine footprints based on real-time data collection. The level of investment in excavation support data collection can be balanced against potential cost savings realized through waste stream minimization. Secure project support Web sites ensure that data sets generated during the remediation process are readily accessible to all who need to see them, whether they are on site or not. These include regulators, program managers, and technical support staff. This type of Web site allows for quick problem resolution, increased transparency in field decision making, and more efficient allocation of expensive technical staff time

The Avaldsnes Royal Manor Project’s Research Plan and Excavation Objectives

OpenAIRE

Skre, Dagfinn

2017-01-01

This chapter provides an outline of the scholarly problems that the Avaldsnes Royal Manor Project was designed to address, the central theme explored being the political institutions and processes in the first millennium AD. The research plan was developed during the 2007–9 pilot project phase, and was adjusted and supplemented during the 2011–12 excavations and the research and publication phase in the subsequent years. The first of the research plan’s two sections, the results of which are ...

Radon in an underground excavation site in Helsinki

International Nuclear Information System (INIS)

Venelampi, E.

2004-01-01

The paper reports on radon measurements and actions taken in a large underground excavation site in Helsinki, where a coal store was excavated underneath an existing power plant. The measurements were carried out by taking grab samples using Lucas type scintillation cells. Large variations in radon concentrations were observed during the three-year study. The reasons for variations are discussed and recommendations are given for radon monitoring procedures in underground excavation sites. The importance of ventilation to reduce the radon level is stressed. (P.A.)

Identifying the cutting tool type used in excavations using neural networks

Energy Technology Data Exchange (ETDEWEB)

Jonak, J.; Gajewski, J. [Lublin University of Technology, Lublin (Poland). Faculty of Mechanical Engineering

2006-03-15

The paper presents results of preliminary research on utilising neural networks to identify excavating cutting tool's type used in multi-tool excavating heads of mechanical coal miners. Such research is necessary to identify rock excavating process with a given head, and construct adaptation systems for control of excavating process with such a head.

Finite-element modelling of geomechanical and hydraulic responses to the room 209 heading extension excavation response experiment 2: post-excavation analysis of experimental results

Energy Technology Data Exchange (ETDEWEB)

Chan, T; Griffith, P; Nakka, B W; Khair, K R

1993-07-01

An in situ excavation response test was conducted at the 240 Level of the Underground Research Laboratory (URL) in conjunction with the excavation of a tunnel (Room 209) through a narrow, near-vertical, water-bearing fracture oriented almost perpendicular to the tunnel axis. This report presents a post-excavation analysis of the predicted mechanical response of the granitic rock mass to the tunnel excavation and the near-field hydraulic response of the fracture zone, compares the numerical modelling predictions with the actual measured response, provides information on the rock mass and fracture from back-analysis of the responses, and makes recommendations for future experiments. Results indicate that displacements and stress changes were reasonably well predicted. Pressure drops at hydrology boreholes and inflow to the tunnel were overpredicted, and fracture permeability changes were underpredicted. The permeability change is considered too large to be solely stress-induced. The back-calculated deformation modulus indicated nonlinear softening of the rock within 3.5 m of the tunnel wall. This is likely due to both excavation damage and the confining stress dependence of the modulus. For future excavation experiments it is recommended that mechanical excavation should replace the drill-and-blast technique; excavation damage should be incorporated into mechanical models; an improved hydraulic fracture model should be developed; and a coupled geomechanical-hydraulic analysis of fracture flow should be developed. (author). 16 refs., 15 tabs., 156 figs.

Finite-element modelling of geomechanical and hydraulic responses to the room 209 heading extension excavation response experiment 2: post-excavation analysis of experimental results

International Nuclear Information System (INIS)

Chan, T.; Griffith, P.; Nakka, B.W.; Khair, K.R.

1993-07-01

An in situ excavation response test was conducted at the 240 Level of the Underground Research Laboratory (URL) in conjunction with the excavation of a tunnel (Room 209) through a narrow, near-vertical, water-bearing fracture oriented almost perpendicular to the tunnel axis. This report presents a post-excavation analysis of the predicted mechanical response of the granitic rock mass to the tunnel excavation and the near-field hydraulic response of the fracture zone, compares the numerical modelling predictions with the actual measured response, provides information on the rock mass and fracture from back-analysis of the responses, and makes recommendations for future experiments. Results indicate that displacements and stress changes were reasonably well predicted. Pressure drops at hydrology boreholes and inflow to the tunnel were overpredicted, and fracture permeability changes were underpredicted. The permeability change is considered too large to be solely stress-induced. The back-calculated deformation modulus indicated nonlinear softening of the rock within 3.5 m of the tunnel wall. This is likely due to both excavation damage and the confining stress dependence of the modulus. For future excavation experiments it is recommended that mechanical excavation should replace the drill-and-blast technique; excavation damage should be incorporated into mechanical models; an improved hydraulic fracture model should be developed; and a coupled geomechanical-hydraulic analysis of fracture flow should be developed. (author). 16 refs., 15 tabs., 156 figs

Choroidal Excavation in Eye with Normal Tension Glaucoma

Directory of Open Access Journals (Sweden)

Kazunobu Asao

2014-05-01

Full Text Available Purpose: To report the case of an eye with normal tension glaucoma and a choroidal excavation. Methods: This is an observational case report. Results: A 59-year-old woman with normal tension glaucoma had a choroidal excavation in the left eye. Her best-corrected visual acuity and intraocular pressure were within normal limits and had been stable for 5 years. Fundus examination showed a small white lesion inferior to the macula and a nerve fiber layer defect at the inferior edge of the optic disc. Humphrey Field Analyzer (HFA showed visual field defects corresponding to the nerve fiber layer defect with C30-2, and a central scotoma superior to the macula with C10-2. Optical coherence tomography (OCT showed a 150-µm deep choroidal excavation. Disruptions of the IS/OS line were detected only in the area inferior to the choroidal excavation. During the 5 months of follow-up, her best-corrected visual acuity remained at 1.0 and the IOP ranged from 12 to 14 mm Hg in the left eye. The fundus and OCT images did not deteriorate and the choroidal excavation did not enlarge. Conclusions: The disruption of the inner/outer segment (IS/OS line was detected only at the area surrounding the choroidal excavation. OCT examinations are useful in assessing the area of the residual IS/OS line, and HFA can be used to estimate the residual central visual field.

Massachusetts Institute of Technology / Andres Sevtshuk

Index Scriptorium Estoniae

Sevtshuk, Andres, 1981-

2006-01-01

A. Sevtshuk oma magistritööst "The Self-aware City / Enesest teadlik linn". Juhendaja William J. Mitchell. Koolist Massachusetts Institute of Technology, selle arhitektuuriosakonnast, arhitektuuri teadusmagistrantuurist

A STRUCTURAL MODEL OF AN EXCAVATOR WORKFLOW CONTROL SYSTEM

Directory of Open Access Journals (Sweden)

A. Gurko

2016-12-01

Full Text Available Earthwork improving is connected with excavators automation. In this paper, on the basis of the analysis of problems that a hydraulic excavator control system have to solve, the hierarchical structure of a control system have been proposed. The decomposition of the control process had been executed that allowed to develop the structural model which reflects the characteristics of a multilevel space-distributed control system of an excavator workflow.

Influence of hole depth on output when excavating veins by small cuts to the course with the use of monorail stope equipment complexes

International Nuclear Information System (INIS)

Galchenko, Y.P.; Dadakuziev, B.M.; Saifutdinov, Y.N.

1986-01-01

A new comprehensive mechanization technology is discussed that uses monorail equipment installed along the course of the ore body. Trials of this machinery confirmed its efficiency, and a government commission has recommended the new technology for broad introduction in mines. The stope equipment complex with monorail advance has been recommended for mass production. It was noted that methods for determining the efficient parameters of the stope must be developed, especially a technique for estimating the breadth of the excavation cut as the principal indicator determining the cost-effectiveness and quality of stope excavation of veins worked to the course. An expression is presented that makes it possible to estimate the upper limit of the variation of hole depth that provides for the maximum excavation of the pay reserves

Analysis of technological, institutional and socioeconomic factors ...

African Journals Online (AJOL)

Analysis of technological, institutional and socioeconomic factors that influences poor reading culture among secondary school students in Nigeria. ... Proliferation and availability of smart phones, chatting culture and social media were identified as technological factors influencing poor reading culture among secondary ...

Greenhouse Gas Emissions from Excavation on Residential Construction Sites

Directory of Open Access Journals (Sweden)

Perry Forsythe

2014-12-01

Full Text Available Despite considerable research concerning the manifestation of greenhouse gases in the usage of buildings, little has been done concerning emissions arising from the construction process itself. This paper specifically examines emissions arising from cut and fill excavation on residential construction sites. Even though such excavation is often seen as being economical in terms of providing a flat base for concrete raft slab construction, the environmental consequences of this approach need to be considered more fully in terms of impact on the environment. This is particularly important when steeply sloping sites are involved and for different soil types. The paper undertakes a study that quantitatively assesses the cumulative greenhouse gas emissions caused by cut and fill excavation on 52 residential projects in Australia for a range of slope and soil types. The paper presents results from the study and concludes that greenhouse gas emissions increase as site slope increases; the building footprint area (as distinct from Gross Floor Area, exposes the need to reduce the area of the building to reduce greenhouse gas emissions; excavation of rock soils creates higher emissions than other soil types; and cut and fill excavation on steeply slope sites increase emissions. Potential alternative construction includes suspended floor construction systems which involve less excavation.

Greenhouse Gas Emissions from Excavation on Residential Construction Sites

Directory of Open Access Journals (Sweden)

Perry Forsythe

2014-12-01

Full Text Available Despite considerable research concerning the manifestation of greenhouse gases in the usage of buildings, little has been done concerning emissions arising from the construction process itself. This paper specifically examines emissions arising from cut and fill excavation on residential construction sites. Even though such excavation is often seen as being economical in terms of providing a flat base for concrete raft slab construction, the environmental consequences of this approach need to be considered more fully in terms of impact on the environment. This is particularly important when steeply sloping sites are involved and for different soil types. The paper undertakes a study that quantitatively assesses the cumulative greenhouse gas emissions caused by cut and fill excavation on 52 residential projects in Australia for a range of slope and soil types. The paper presents results from the study and concludes that greenhouse gas emissions increase as site slope increases; the building footprint area (as distinct from Gross Floor Area, exposes the need to reduce the area of the building to reduce greenhouse gas emissions; excavation of rock soils creates higher emissions than other soil types; and cut and fill excavation on steeply slope sites increase emissions. Potential alternative construction includes suspended floor construction systems which involve less excavation. 

Mechanical excavator performance in Yucca Mountain tuffs

International Nuclear Information System (INIS)

Ozdemir, L.; Hansen, F.D.

1991-01-01

A research effort of four phases is in progress at the Colorado School of Mines. The overall program will evaluate the cutability of welded tuff and other lithologies likely to be excavated at Yucca Mountain in the site characterization process. Several mechanical systems are considered with emphasis given to the tunnel boring machine. The research comprises laboratory testing, linear drag bit and disc cutter tests and potentially large-scale laboratory demonstrations to support potential use of a tunnel boring machine in welded tuff. Preliminary estimates of mechanical excavator performance in Yucca Mountain tuff are presented here. As phases of the research project are completed, well quantified estimates will be made of performance of mechanical excavators in the Yucca Mountain tuffs. 3 refs., 2 tabs

Mechanical excavator performance in Yucca Mountain tuffs

International Nuclear Information System (INIS)

Ozdemir, L.; Hansen, F.D.

1991-01-01

A research effort of four phases is in progress at the Colorado School of Mines. The overall program will evaluate the cutability of welded tuff and other lithologies likely to be excavated at Yucca Mountain in the site characterization process. Several mechanical systems are considered with emphasis given to the tunnel boring machine. The research comprises laboratory testing, linear drag bit and disc cutter tests, and potentially large-scale lab. demonstrations to support potential use of a tunnel boring machine in welded tuff. Preliminary estimates of mechanical excavator performance in Yucca Mountain tuff are presented here. As phases of the research project are completed, well-quantified estimates will be made of performance of mechanical excavators in the Yucca Mountain tuffs

Bringing Technology and Meaning into Institutional Work

DEFF Research Database (Denmark)

Raviola, Elena; Nörbäck, Maria

2013-01-01

In this article we investigate the role of technology and meaning in the institutional work of newsmakers. By analysing ethnographic data from an Italian business newspaper undertaking a project integrating the print and online newsrooms, we show how technology makes certain actions possible...

Strategic Planning in Ireland's Institutes of Technology

Science.gov (United States)

Elwood, Larry; Rainnie, Al

2012-01-01

This article focuses upon Ireland's institute of technology sector, which has been transformed from a 1970s technical orientation to its broader current role of research and higher education provision. The transformational shifts experienced by institutes over the previous three decades have been profound: increased autonomy, new managerial and…

Excavation of LSS1

CERN Multimedia

CERN PhotoLab

1972-01-01

Excavation of the long straight-section LSS1 by an Alpine boring machine. View of the connection chamber, in the background, the roofs of the enlarged sections (8.5 m and 6 m). On the right, the access tunnel to PP1.

Impact of Drill and Blast Excavation on Repository Performance Confirmation

International Nuclear Information System (INIS)

Keller, R.; Francis, N.; Houseworth, J.; Kramer, N.

2000-01-01

There has been considerable work accomplished internationally examining the effects of drill and blast excavation on rock masses surrounding emplacement openings of proposed nuclear waste repositories. However, there has been limited discussion tying the previous work to performance confirmation models such as those proposed for Yucca Mountain, Nevada. This paper addresses a possible approach to joining the available information on drill and blast excavation and performance confirmation. The method for coupling rock damage data from drill and blast models to performance assessment models for fracture flow requires a correlation representing the functional relationship between the peak particle velocity (PPV) vibration levels and the potential properties that govern water flow rates in the host rock. Fracture aperture and frequency are the rock properties which may be most influenced by drill and blast induced vibration. If it can be shown (using an appropriate blasting model simulation) that the effect of blasting is far removed from the waste package in an emplacement drift, then disturbance to the host rock induced in the process of drill and blast excavation may be reasonably ignored in performance assessment calculations. This paper proposes that the CANMET (Canada Center for Mineral and Energy Technology) Criterion, based on properties that determine rock strength, may be used to define a minimum PPV. This PPV can be used to delineate the extent of blast induced damage. Initial applications have demonstrated that blasting models can successfully be coupled with this criterion to predict blast damage surrounding underground openings. The Exploratory Studies Facility at Yucca Mountain has used a blasting model to generate meaningful estimates of near-field vibration levels and damage envelopes correlating to data collected from pre-existing studies conducted. Further work is underway to expand this application over a statistical distribution of geologic

Telerobotic Excavator Designed to Compete in NASA's Lunabotics Mining Competition

Science.gov (United States)

Nash, Rodney; Santin, Cara; Yousef, Ahmed; Nguyen, Thien; Helferty, John; Pillapakkam, Shriram

2011-01-01

The second annual NASA Lunabotics Mining competition is to be held in May 23-28, 2011. The goal of the competition is for teams of university level students to design, build, test and compete with a fully integrated lunar excavator on a simulated lunar surface. Our team, named Lunar Solutions I, will be representing Temple University's College of Engineering in the competition. The team's main goal was to build a robot which is able to compete with other teams, and ultimately win the competition. The main challenge of the competition was to build a wireless robot that can excavate and collect a minimum of 10 kilograms of the regolith material within 15 minutes. The robot must also be designed to operate in conditions similar to those found on the lunar surface. The design of the lunar excavator is constrained by a set of requirements determined by NASA and detailed in the competition's rulebook. The excavator must have the ability to communicate with the "main base" wirelessly, and over a Wi-Fi network. Human operators are located at a remote site approximately 60 meters away from the simulated lunar surface upon which the robot must excavate the lunar regolith surface. During the competition, the robot will operate in a separate area from the control room in an area referred to as the "Lunarena." From the control room, the operators will have to control the robot using visual feedback from cameras placed both within the arena and on the robot. Using this visual feedback the human operators control the robots movement using both keyboard and joystick commands. In order to place in the competition, a minimum of 10 kg of regolith material has to be excavated, collected, and dumped into a specific location. For that reason, the robot must be provided with an effective and powerful excavation system. Our excavator uses tracks for the drive system. After performing extensive research and trade studies, we concluded that tracks would be the most effective method for

Historical photogrammetry: Bird's Paluxy River dinosaur chase sequence digitally reconstructed as it was prior to excavation 70 years ago.

Science.gov (United States)

Falkingham, Peter L; Bates, Karl T; Farlow, James O

2014-01-01

It is inevitable that some important specimens will become lost or damaged over time, conservation is therefore of vital importance. The Paluxy River dinosaur tracksite is among the most famous in the world. In 1940, Roland T. Bird described and excavated a portion of the site containing associated theropod and sauropod trackways. This excavated trackway was split up and housed in different institutions, and during the process a portion was lost or destroyed. We applied photogrammetric techniques to photographs taken by Bird over 70 years ago, before the trackway was removed, to digitally reconstruct the site as it was prior to excavation. The 3D digital model offers the opportunity to corroborate maps drawn by R.T. Bird when the tracksite was first described. More broadly, this work demonstrates the exciting potential for digitally recreating palaeontological, geological, or archaeological specimens that have been lost to science, but for which photographic documentation exists.

Digital technologies in Day-care institutions

DEFF Research Database (Denmark)

Schrøder, Vibeke; Søndergaard, Steen

Digital technologies are gaining an ever increasing access into the activities in Danish and Nordic day-care institutions. The traditional critical viewpoint of technologies as being opposed to the well-being of children is challenged in part by substantial access to digital tools in infant life......, in part by new technologies designed with an intuitive and inviting user interface. In a one-year research project ’Digital tools in day-care-institutions’ (2015) financed by The Danish Agency for Digitisation and The Ministry of Education we have investigated the role of digital technologies in relation...... in performances of dominant cultural ways of acting and thinking. Also, most often the pedagogues’ use of technologies follow the immediate possibilities offered by the technologies. From the videos of these activities it appears that the children follow two tracks of participation. Either the children work...

Three-Dimensional Laser Scanning for Geometry Documentation and Construction Management of Highway Tunnels during Excavation

Science.gov (United States)

Gikas, Vassilis

2012-01-01

Driven by progress in sensor technology, computer software and data processing capabilities, terrestrial laser scanning has recently proved a revolutionary technique for high accuracy, 3D mapping and documentation of physical scenarios and man-made structures. Particularly, this is of great importance in the underground space and tunnel construction environment as surveying engineering operations have a great impact on both technical and economic aspects of a project. This paper discusses the use and explores the potential of laser scanning technology to accurately track excavation and construction activities of highway tunnels. It provides a detailed overview of the static laser scanning method, its principles of operation and applications for tunnel construction operations. Also, it discusses the planning, execution, data processing and analysis phases of laser scanning activities, with emphasis given on geo-referencing, mesh model generation and cross-section extraction. Specific case studies are considered based on two construction sites in Greece. Particularly, the potential of the method is examined for checking the tunnel profile, producing volume computations and validating the smoothness/thickness of shotcrete layers at an excavation stage and during the completion of excavation support and primary lining. An additional example of the use of the method in the geometric documentation of the concrete lining formwork is examined and comparisons against dimensional tolerances are examined. Experimental comparisons and analyses of the laser scanning method against conventional surveying techniques are also considered. PMID:23112655

CERN Central Library : 2000 year old technology transfer. Two fragments of columns from a Roman building discovered during excavations for the PS in 1956 have prominent places in the Library where they can be enjoyed by all

CERN Multimedia

Laurent Guiraud

2001-01-01

CERN Central Library : 2000 year old technology transfer. Two fragments of columns from a Roman building discovered during excavations for the PS in 1956 have prominent places in the Library where they can be enjoyed by all

Annual report 2015 of the Institute for Nuclear and Energy Technologies

Energy Technology Data Exchange (ETDEWEB)

Schulenberg, Thomas

2016-07-01

The annual report of the Institute for Nuclear and Energy Technologies of KIT summarizes its research activities and provides some highlights of each working group, like thermal-hydraulic analyses for nuclear fusion reactors, accident analyses for light water reactors, and research on innovative energy technologies: liquid metal technologies for energy conversion, hydrogen technologies and geothermal power plants. The institute has been engaged in education and training in energy technologies.

Institutional Educational Technology Policy and Strategy Documents: An Inequality Gaze

Science.gov (United States)

Czerniewicz, Laura; Rother, Kyle

2018-01-01

Issues of inequality in higher education have received considerable attention in recent decades, but the intersection of inequality and educational technology at an institutional level has received little attention. This study aims to provide a perspective on institutional educational technology policy informed by current understandings of…

Development of a teleoperated backhoe for buried waste excavation

International Nuclear Information System (INIS)

Burks, B.L.; Killough, S.M.; Thompson, D.H.

1992-01-01

For nearly five decades the United States (US) Department of Energy (DOE) and its predecessor agencies have engaged in broad-based research and development activities as well as nuclear weapons component production. As a by-product of these activities, large quantities of waste materials have been granted. One of the most common approaches used for solid waste storage was to bury waste containers in pits and trenches. With the current emphasis on environmental restoration, DOE now plans to either retrieve much of the legacy of buried waste or stabilize the waste in place via in situ vitrification or other means. Because of the variety of materials that have been buried over the years, the hazards of retrieval are significant if performed using conventional manned operations. The potential hazards, in addition to radiation exposure, include pyrophorics, toxic chemicals, and explosives. Although manifests exist for much of the buried waste, these records are often incomplete compared to today's requirements. Because of the potential hazards and uncertainty about waste contents and container integrity, it is highly desirable to excavate these wastes using remotely operated equipment. In this paper the authors describe the development of a teleoperated military tractor called the Small Emplacement Excavator (SEE). Development of the SEE is being funded jointly by both DOE and the US Army. The DOE sponsor is the Office of Technology Development (OTD) Robotics Program. The US Army sponsor is the Program Manager for Ammunition Logistics, Picatinny Arsenal. The primary interest for DOE is in the application to remote excavation of buried waste, while the primary emphasis for the US Army is in the remote retrieval of unexploded ordnance. Technical requirements for these two tasks are very similar and, therefore, justify a joint development project. 1 ref

Determination of near field excavation disturbance in crystalline rock

International Nuclear Information System (INIS)

Koopmans, R.; Hughes, R.W.

1986-01-01

The computerized dilatometer system has rapidly and economically provided deformation moduli of low and high modulus rock, determined the extent of excavation disturbance surrounding an underground opening and located open fracture within a rock mass. Results from both test sites indicate that the moduli obtained were influenced by the in situ tangential stress field. It has been shown that the near field excavation disturbance is kept to a minimum through the use of careful excavation techniques such as the tunnel boring machine. In turn, the in situ tangential stress levels and deformation moduli are maximized while the corresponding permeability is minimized

Radiant Research. Institute for Energy Technology 1948-98

International Nuclear Information System (INIS)

Njoelstad, Olav

1999-01-01

Institutt for Atomenergi (IFA), or Institute for Atomic Energy, at Kjeller, Norway, was founded in 1948. The history of the institute as given in this book was published in 1999 on the occasion of the institute's 50th anniversary. The scope of the institute was to do research and development as a foundation for peaceful application of nuclear energy and radioactive substances in Norway. The book tells the story of how Norway in 1951 became the first country after the four superpowers and Canada to have its own research reactor. After the completion of the reactor, the institute experienced a long and successful period and became the biggest scientific and technological research institute in Norway. Three more reactors were built, one in Halden and two at Kjeller. Plans were developed to build nuclear powered ships and nuclear power stations. It became clear, however, in the 1970s, that there was no longer political support for nuclear power in Norway, and it was necessary for the institute to change its research profile. In 1980, the institute changed its name to Institutt for energiteknikk (IFE), or Institute for energy technology, to signal the broadened scope. The book describes this painful but successful readjustment and shows how IFE in the 1980s and 1990s succeeded in using its special competence from the nuclear field to establish special competence in new research fields with great commercial potential

Archaeological Excavation and Deep Mapping in Historic Rural Communities

Directory of Open Access Journals (Sweden)

Carenza Lewis

2015-09-01

Full Text Available This paper reviews the results of more than a hundred small archaeological “test pit” excavations carried out in 2013 within four rural communities in eastern England. Each excavation used standardized protocols in a different location within the host village, with the finds dated and mapped to create a series of maps spanning more than 3500 years, in order to advance understanding of the spatial development of settlements and landscapes over time. The excavations were all carried out by local volunteers working physically within their own communities, supported and advised by professional archaeologists, with most test pits sited in volunteers’ own gardens or those of their friends, family or neighbors. Site-by-site, the results provided glimpses of the use made by humans of each of the excavated sites spanning prehistory to the present day; while in aggregate the mapped data show how settlement and land-use developed and changed over time. Feedback from participants also demonstrates the diverse positive impacts the project had on individuals and communities. The results are presented and reviewed here in order to highlight the contribution archaeological test pit excavation can make to deep mapping, and the contribution that deep mapping can make to rural communities.

Mobile technologies and the spatiotemporal configurations of institutional practice

DEFF Research Database (Denmark)

Shklovski, Irina; Troshynski, Emily; Dourish, Paul

2015-01-01

are specifically concerned with what happens to institutional roles, power relationships, and decision-making processes when a particular type of information—that of spatiotemporal location of people—is made into a technologically tradable object through the use of location-based systems. We examine...... in which broad adoption of location-based and mobile technologies has the capacity to radically reconfigure the spatiotemporal arrangement of institutional processes. The presence of digital location traces creates new forms of institutional accountability, facilitates a shift in the understood relation...... between location and action, and necessitates new models of interpretation and sense making in practice....

BILATERAL CHOROIDAL EXCAVATION IN JUVENILE LOCALIZED SCLERODERMA.

Science.gov (United States)

Franklin, Mackenzie L; Day, Shelley

2018-01-01

To describe a case of bilateral choroidal excavation in a patient with juvenile localized scleroderma. Case report. An asymptomatic 12-year-old boy with localized scleroderma presented for examination and was found to have bilateral areas of choroidal excavation temporal to the fovea. Previous reports of ocular complications of localized scleroderma have primarily described adnexal and anterior segment changes. This is the second report of choroidal changes in a patient with localized scleroderma, and the first in a pediatric patient.

MATHEMATICAL MODEL OF ATTITUDE CONTROL BUCKET‐WHEEL EXCAVATOR

Directory of Open Access Journals (Sweden)

Ivana ONDERKOVÁ

2013-07-01

Full Text Available This lecture deals with the application problems of convertibility GPS system at paddle excavator K 800. The claims of the modern operating surface mining of the excavators requires a lot of information for monitoring of mining process, capacity mining, selective extraction etc. The utilization of monitoring the excavator setting by GPS system proved to be the only one proper because the receivers are resistant to the vibration, dust, temperature divergence and weather changeable. Only the direct contact with communications satellite is required. It means that they can´t be located in a metal construction space (shadow caused by construction elements, influence of electrical high voltage cables even they can´t be located close to the paddle wheel on the paddle boom (shadow possibility caused by cuttinng edge created during lower gangplanks mining. This is the reason that GPS receivers are set uppermost on the metal construction excavator and the mathematical formulation is required for determination of paddle wheel petting. The relations for calculation of the paddle wheel coordinate were defined mathematically and after that the mathematical model was composed.

Utilization of thin-layer chromatography for confirmational sampling during remedial excavation

International Nuclear Information System (INIS)

Burton, P.J.

1996-01-01

Thin-layer chromatography (TLC) is a simple, efficient, inexpensive, and accurate method of chemical analysis. This method is applicable to field testing for confirming the limits of excavation during excavation of petroleum, oil, and/or lubricant (POL) contamination. Traditionally, excavation at contaminated sites suffers from a time delay due to the need to obtain laboratory confirmation of the limits of excavation. All suspected contaminated material is removed for stockpiling or remediation. The remaining soils need to be sampled to confirm that no contaminated material remains in the excavation. The site scientist collects samples and sends them out for analysis at a certified laboratory. The laboratory requires, even for a rush order, several days to analyze the samples. This time delay interferes with the efficiency of the operation. The excavations either have to be left open (which is a safety hazard) or reopened if additional material must be excavated. TLC samples can be collected and analyzed in several hours allowing for a short turnaround time for analytical results. The TLC method can be easily performed by a technician. Results of a case study from a subarctic Alaskan site will be reported. Simple operational TLC procedures will be shared. The equipment required for TLC analysis will be outlined. Correlation data between TLC and laboratory analysis will be presented

Shaft Boring Machine: A method of mechanized vertical shaft excavation

International Nuclear Information System (INIS)

Goodell, T.M.

1991-01-01

The Shaft Boring Machine (SBM) is a vertical application of proven rock boring technology. The machine applies a rotating cutter wheel with disk cutters for shaft excavation. The wheel is thrust against the rock by hydraulic cylinders and slews about the shaft bottom as it rotates. Cuttings are removed by a clam shell device similar to conventional shaft mucking and the muck is hoisted by buckets. The entire machine moves down (and up) the shaft through the use of a system of grippers thrust against the shaft wall. These grippers and their associated cylinders also provide the means to maintain verticality and stability of the machine. The machine applies the same principles as tunnel boring machines but in a vertical mode. Other shaft construction activities such as rock bolting, utility installation and shaft concrete lining can be accomplished concurrent with shaft boring. The method is comparable in cost to conventional sinking to a depth of about 460 meters (1500 feet) beyond which the SBM has a clear host advantage. The SBM has a greater advantage in productivity in that it can excavate significantly faster than drill and blast methods

Institute for safety technology

International Nuclear Information System (INIS)

1991-01-01

In the area of nuclear reactor safety studies, the Institute for Safety Technology (STI) concentrated its efforts in analysing experimentally and numerically phenomena which characterize highly-improbable but very severe accidents either for light water or for sodium cooled reactors. In the STI nuclear isle, three new laboratories for waste (PETRA), fusion (ETHEL) and safeguards, (PERLA) activities are approaching completion and have made substantial progress in their licensing procedure. The Institute started activities in the non-nuclear safety research area only a few years ago and has been able this year to present its first significant experimental and theoretical results in the areas of runaway reactions, accidental release of products and their deflagration/detonation. Concerning Reference Methods for the Evaluation of Structure Reliability a better understanding was gained of the nonlinear cyclic and dynamic behaviour of materials and structures by performing experiments and developing constitutive and structural member models leading to the computer simulation of complete structures

Heathrow Terminal 5 Excavation Archive (Data Paper

Directory of Open Access Journals (Sweden)

Framework Archaeology

2014-06-01

Full Text Available Framework Archaeology is a Joint Venture agreement between Oxford Archaeology (OA and Wessex Archaeology (WA to provide archaeological services to BAA (formerly British Airports Authority, now Heathrow Airport Holdings Ltd. Given the potential scale of some of BAA's projects, the joint venture enables Framework Archaeology to draw on the full resources of both OA and WA, including site staff, specialist managers, administrative support, and technical facilities. In 1993, BAA plc and Heathrow Airport Limited submitted a joint planning application to develop an additional passenger terminal complex (Terminal 5, together with the provision of aircraft aprons and taxiways, and include the realignment of rivers and landscaping. The resulting archaeological excavations were undertaken as three main phases of work. Excavations in 1996 by the Museum of London Archaeology Service of approximately 4 ha of sludge stockpile areas (site code POK96. Between 1999-2000 Framework Archaeology excavated approximately 21 ha in the Perry Oaks sludge works and adjacent areas (WPR98. Framework Archaeology also undertook excavations between 2002-2007 as part of the construction of Terminal 5 (PSH02, TEC05 covering a further 50 hectares. Importantly the aim of the Terminal 5 archaeological programme was to move beyond the description and recovery of archaeological remains and to arrive at an understanding of the history of human inhabitation and the practical ways in which people established their presence in the material, social and political conditions of their day.

Determining the productivity of frontal-selective excavation equipment

Energy Technology Data Exchange (ETDEWEB)

Baikenzhin, A E; Ermekov, T E

1979-01-01

The engineering parameters of the VMF-2 frontal-selective excavation machine are given. Calculation formulae are given for determining the feed speed of the working tool relative to the difference in the motion of the arm of the working tool and the feed speed of the hydraulic jack lifter. A methodology is developed for calculating the productivity of the excavator depending on various engineering conditions, accounting for modifications in its design.

Institute for Energy Technology, Annual Report 1981

International Nuclear Information System (INIS)

1982-03-01

The annual report gives a brief account of the activities of Institute for Energy Technology and presents a fairly comprehensive anasis of the budgetary dispositions in 1981 and, for comparison, 1980. (RF)

National financial institutions and technological development

Energy Technology Data Exchange (ETDEWEB)

Ramesh, J

1979-12-01

The impact of technological policies on non-technological institutions is examined to see what some of the side effects are and how they can serve the needs of the local financial and productive sector. The interrelationships of the national financial systems with government departments, local infrastructure, local private sector, and international financing agencies are examined in the historical context of several development projects. The wrong emphasis is shown to be used by many technological planners, whose first consideration should be to build a loca planning and investment capability and to train local human resources to assume a decision-making role. The neglect seen in India, Brazil, and other countries is traced to the motivation of the industrial enterprises. A more-suitable technological policy could introduce the concepts of loan evaluation on the basis of technological criteria and fiscal incentives. 24 references, 1 figure, 4 tables. (DCK)

Pajarito Plateau archaeological surveys and excavations. II

Energy Technology Data Exchange (ETDEWEB)

Steen, C R

1982-04-01

Los Alamos National Laboratory continues its archaeological program of data gathering and salvage excavations. Sites recently added to the archaeological survey are described, as well as the results of five excavations. Among the more interesting and important discoveries are (1) the apparently well-established local use of anhydrous lime, and (2) a late pre-Columbian use of earlier house sites and middens for garden plots. Evidence indicated that the local puebloan population was the result of an expansion of upper Rio Grande peoples, not an influx of migrants.

Room 209 excavation response test in the underground research laboratory

International Nuclear Information System (INIS)

Lang, P.A.

1989-01-01

An in situ excavation response test was conducted at the Canadian Underground Research Laboratory (URL) in conjunction with excavation of a tunnel (Room 209) through a near-vertical water-bearing fracture oriented perpendicular to the tunnel axis. Encountering a fracture with such desirable characteristics provided a unique opportunity during construction of the URL to try out instrumentation and analytical methods for use in the Excavation Response Experiment (ERE) planned as one of the major URL experiments. The test has produced a valuable data set for validating numerical models. Four modelling groups predicted the response that would be monitored by the instruments. The predictions of the mechanical response were generally good. However, the predictions of the permeability and hydraulic pressure changes in the fracture, and the water flows into the tunnel, were poor. It is concluded that we may not understand the mechanisms that occur in the fracture in response to excavation. Laboratory testing, and development of a contracting joint code, has been initiated to further investigate this phenomenon. Preliminary results indicate that the excavation damaged zone in the walls and crown is less than 0.5 m thick and has relatively low permeability. The damaged zone in the floor is at least 1 m thick and has relatively high permeability. The damage in the floor could be reduced in future excavations by using controlled blasting methods similar to those used for the walls and crown

A study experiment of auto idle application in the excavator engine performance

Energy Technology Data Exchange (ETDEWEB)

Purwanto, Wawan, E-mail: wawan5527@gmail.com; Maksum, Hasan; Putra, Dwi Sudarno, E-mail: dwisudarnoputra@ft.unp.ac.id; Wahyudi, Retno [State University of Padang, West Sumatera (Indonesia); Azmi, Meri, E-mail: meriazmi@gmail.com [State Polytechnic of Padang, West Sumatera (Indonesia)

2016-03-29

The purpose of this study was to analyze the effect of applying auto idle to excavator engine performance, such as machine unitization and fuel consumption in Excavator. Steps to be done are to modify the system JA 44 and 67 in Vehicle Electronic Control Unit (V-ECU). The modifications will be obtained from the pattern of the engine speed. If the excavator attachment is not operated, the engine speed will return to the idle speed automatically. From the experiment results the auto idle reduces fuel consumption in excavator engine.

Excavated rock materials from tunnels for sprayed concrete

OpenAIRE

Luong, Judy Yuen Wah; Aarstad, Kari; De Weerdt, Klaartje; Bjøntegaard, Øyvind

2017-01-01

Sand extracted from natural resources is widely used in concrete production nowadays. The increase in demand for concrete production has resulted in shortage of natural sand resources, especially in terms of suitable materials for concrete production. At the same time, large amounts of excavated rock materials are and have been generated from tunnelling projects and discarded. Hence, there is an opportunity to use these excavated rock materials as aggregates for concrete production. The chall...

Summary of nuclear-excavation applications

International Nuclear Information System (INIS)

Toman, John

1970-01-01

Although many nuclear-excavation applications have been proposed, few have been seriously considered and none have been brought to fruition. This paper summarizes and discusses specific examples of a canal, a harbor, a highway cut and a nuclear quarry, all of which have been studied in some detail. It is believed that useful demonstration projects - such as a deep-water harbor and a nuclear quarry - can be safely accomplished with existing technology. Current assessments of the feasibility of constructing a sea-level canal in either Panama or Colombia appear to be favorable from a technical viewpoint. The concept of close spacing in row-charge designs has made it possible to greatly reduce the estimated required salvo yields for both proposed canals. Salvo yields have been reduced from 35 Mt to 13 Mt in Colombia and 11 Mt in Panama. As a result, the seismic motions predicted for large cities in these countries are similar to motions produced in populated areas in the United States by nuclear tests and earthquakes in which no real damage to residential or high-rise structures was noted. (author)

Summary of nuclear-excavation applications

Energy Technology Data Exchange (ETDEWEB)

Toman, John [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

1970-05-01

Although many nuclear-excavation applications have been proposed, few have been seriously considered and none have been brought to fruition. This paper summarizes and discusses specific examples of a canal, a harbor, a highway cut and a nuclear quarry, all of which have been studied in some detail. It is believed that useful demonstration projects - such as a deep-water harbor and a nuclear quarry - can be safely accomplished with existing technology. Current assessments of the feasibility of constructing a sea-level canal in either Panama or Colombia appear to be favorable from a technical viewpoint. The concept of close spacing in row-charge designs has made it possible to greatly reduce the estimated required salvo yields for both proposed canals. Salvo yields have been reduced from 35 Mt to 13 Mt in Colombia and 11 Mt in Panama. As a result, the seismic motions predicted for large cities in these countries are similar to motions produced in populated areas in the United States by nuclear tests and earthquakes in which no real damage to residential or high-rise structures was noted. (author)

SLOPE STABILITY EVALUATION AND EQUIPMENT SETBACK DISTANCES FOR BURIAL GROUND EXCAVATIONS

Energy Technology Data Exchange (ETDEWEB)

MCSHANE DS

2010-03-25

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examines the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38{sup o} or 1.28 horizontal to 1 vertical. Setback distances are measured from the top edge of the slope to the wheels/tracks of the vehicles and heavy equipment being utilized. The computer program utilized in the calculation uses the center of the wheel or track load for the analysis and this difference is accounted for in this evaluation.

Slope Stability Evaluation And Equipment Setback Distances For Burial Ground Excavations

International Nuclear Information System (INIS)

Mcshane, D.S.

2010-01-01

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examines the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38 o or 1.28 horizontal to 1 vertical. Setback distances are measured from the top edge of the slope to the wheels/tracks of the vehicles and heavy equipment being utilized. The computer program utilized in the calculation uses the center of the wheel or track load for the analysis and this difference is accounted for in this evaluation.

The Use of Ground Penetrating Radar to extend the Results of Archaeological Excavation

Science.gov (United States)

Utsi, E.

2009-04-01

The condition of the Romano-British archaeological site in Wortley, Gloucestershire, UK is typical of sites of the period in that it has been heavily robbed out since it first fell into disuse. Building materials taken from the site have been re-used over the centuries to construct other local buildings. This makes both preservation of the extant remains and interpretation of the excavation problematic. Following the accidental discovery of the site in the 1980s, a programme of excavation was set in place. This excavation was run as a practical archaeological training school and, as a result, a wide range of archaeological and geophysical techniques were applied to the site. This included the introduction of Ground Penetrating Radar (GPR). The preliminary results of the first GPR used on site were not entirely satisfactory which led to the development of a new radar in the early 1990s, specifically developed for use on archaeological sites. The excavation and GPR results were published in a series of excavation reports [1] [2]. It was not possible to excavate fully for two reasons. Firstly the site crossed present day ownership boundaries and secondly the ownership of the excavation area changed. At this point the excavation was summarily terminated. In 2007, permission was given by the owner of an adjacent property to carry out a GPR survey over their land in order to derive additional information, if possible. An area survey was carried out in May 2007 with reduced transect spacing [3]. The radar data showed similar patterning to that of the original investigation i.e. substantial remains which had been subject to a high degree of post-occupational attrition. Time slices from the radar survey were matched to the principal excavation plans. It proved possible to deduce the full extent of certain partially excavated features, notably the courtyard and bath house. It was also possible to demonstrate that one part of the adjacent property did not contain similar

Study on Excavation of Particular Part of Underground Cavern for Hydropower Station

Science.gov (United States)

Yang, Yang; Zhang, Feng; Shang, Qin; Zheng, Huakang

2018-01-01

In the present study, regarding four particular parts of underground cavern for hydropower station, i.e., crown, high sidewall, the intersection between high sidewall and tunnel and tailrace tunnel, by summarizing the previous construction experience, we have proposed the excavation approach based on “middle first and edge later, soft first and hard later”, “layered construction by excavating the thin layer first and supporting as the layer advances”, “tunnel first and wall later, small tunnels into large ones” and “excavating tunnels supported by separation piers”. In addition, the proposed excavation approach has been analyzed and verified with finite element numerical simulation. The result has indicated that the proposed special approach is reasonable and effective to reduce the turbulence on surrounding rocks, lower the influence of unloading during excavating and enhance the local and global stability of caverns and surrounding rocks.

Activities of the work efficiency institute`s department of forestry; Tyoetehoseuran metsaeosaston toiminta

Energy Technology Data Exchange (ETDEWEB)

Maekelae, J

1997-12-31

In accordance with the demarcation of tasks among Finnish forest-engineering research institutions, the Work Efficiency Institute`s Department of Forestry is the only one specialising in research and development focusing on forestry work involving low capital investments and done by landowners on their own estate or on a part-time basis outside their estates. This activity also includes the small-scale utilisation of wood and peat in heating. This bulletin presents a review of our recent research and development work. A significant stepping up of the utilisation of bioenerqy is one of the objectives of the Finnish Government. This has been noted in the Work Efficiency Institute`s Department of Forestry`s work programme in recent years by increasing the role of research and development promoting the consumption of bioenergy. As one of the participants in the National Bioenergy research programme (1993-1998), we are looking into the harvesting of small-diameter wood and wood residues, technology employed in the production of wood chips and fuelwood, cost calculations in fuelwood harvesting, energy entrepreneurship, and the development of fireplaces. Other recent topics of research engaged in by the Department of Forestry include possibilities in the mechanisation of tending of young stands, excavator-loaders in timber harvesting, and promoting self-reliance among landowners in carrying out of forestry work. On-going studies include comparison of pruning methods, a survey of co-operation among landowners at the local community level, and a study looking into the quality of wood produced for delivery sales. (orig.)

Institutional Distance and Partner Selection in International Technological Alliances

NARCIS (Netherlands)

Krammer, Marius

2013-01-01

This study posits that institutional distance has a negative influence on partner selection in international technological alliances. Empirical results based on a dataset of firms in the global tire industry confirm that firms prefer technological partners from closer cognitive, normative and

Investigations of Archaeological Glass Bracelets and Perfume Bottles Excavated in Ancient Ainos (Enez) by Multiple Analytical Techniques

Science.gov (United States)

Celik, S.; Akyuz, T.; Akyuz, S.; Ozel, A. E.; Kecel-Gunduz, S.; Basaran, S.

2018-03-01

Fragments of two perfume bottles belonging to the Hellenistic and Roman periods, and five bracelets belonging to the Roman, Byzantine, and Ottoman periods, excavated in the archaeological site of Enez during the excavations in 2000, have been investigated. The samples were analyzed using micro-Raman, FTIR, and energy dispersive X-ray fluorescence techniques, in order to study the ancient technology of glass production and to determine chemical compositions of the basic components and coloring elements of the glassware. All the investigated glasses can be characterized as low-magnesia-soda-lime silicate glasses, whose colors are induced by metal ions. The melting points of the investigated glasses are estimated to be quite close to each other and around 1000°C.

Prediction of permeability changes in an excavation response zone

International Nuclear Information System (INIS)

Kinoshita, Naoto; Ishii, Takashi; Kuroda, Hidetaka; Tada, Hiroyuki

1992-01-01

In geologic disposal of radioactive wastes, stress changes due to cavern excavation may expand the existing fractures and create possible bypasses for groundwater. This paper proposes a simple method for predicting permeability changes in the excavation response zones. Numerical analyses using this method predict that the response zones created by cavern excavation would differ greatly in thickness and permeability depending on the depth of the cavern site and the initial in-situ stress, that when the cavern site is deeper, response zones would expand more and permeability would increases more, and that if the ratio of horizontal to vertical in-situ stress is small, extensive permeable zones at the crown and the bottom would occur, whereas if the ratio is large, extensive permeable zones would occur in the side walls. (orig.)

On Cultivation of Characteristic Talents in Law in Institutes of Technology

Science.gov (United States)

Li, Hong

2011-01-01

For the time being, professional education of law offered by institutes of technology has become an important component of cultivation of professional talents in law in China. Only if institutes of technology face up with their disadvantages, make full use of their resource advantages and cultivate characteristic talents in law, are they able to…

Design of the human computer interface on the telerobotic small emplacement excavator

International Nuclear Information System (INIS)

Thompson, D.H.; Killough, S.M.; Burks, B.L.; Draper, J.V.

1995-01-01

The small emplacement excavator (SEE) is a ruggedized military vehicle with backhoe and front loader used by the U.S. Army for explosive ordinance disposal (EOD) and general utility excavation activities. This project resulted from a joint need in the U.S. Department of Energy (DOE) for a remote controlled excavator for buried waste operations and the U.S. Department of Defense for remote EOD operations. To evaluate the feasibility of removing personnel from the SEE vehicle during high-risk excavation tasks, a development and demonstration project was initiated. Development of a telerobotic SEE (TSEE) was performed by the Oak Ridge National Laboratory in a project funded jointly by the U.S. Army and the DOE. The TSEE features teleoperated driving, a telerobotic backhoe with four degrees of freedom, and a teleoperated front loader with two degrees of freedom on the bucket. Remote capabilities include driving (forward, reverse, brake, steering), power takeoff shifting to enable digging modes, deploying stabilizers, excavation, and computer system booting

Effect of blasting on output increase of bucket wheel excavators

Energy Technology Data Exchange (ETDEWEB)

Musil, P.

1987-12-01

In brown coal surface mines, consolidated sediments become a problem as mining operations advance into greater depth below the original terrain. Owing to higher digging resistance, the output of bucket wheel excavators drops. This problem may be solved by blasting technology and using drilling machines with higher digging force. This paper describes the blasting operations at the Nastup Mines in Tusmice, Czechoslovakia. About 60% of blasting explosives used is a simple mixture of ammonium nitrate and fuel (ANFO), the rest falls on classic blasting gelatines and blasting explosives plasticized by slurry. It is found that blasting improves output by 30% while electric energy consumption is reduced.

New Design Concept for an Excavator Arms by Using Composite Material

Science.gov (United States)

Solazzi, L.; Assi, A.; Ceresoli, F.

2018-06-01

The purpose of the present paper is to lightweight design an excavator arms, by using a different materials and in particular composite material. Specifically, the research is based on the study of a commercial excavator, by determining its geometry and analyzing the load conditions to which it is exposed. These are determined in relation to either the load diagram of the machine or the possible utilities of the excavator, such as the rotation of the machine. The materials used and implemented in the different analytical and numerical elaborations are classic construction steel S 355 (UNI EN 10025-3), high-resistance steel S 890 (UNI EN 10025-6), aluminum Al 6063 T6 (UNI EN 573-3) and the composite material made by carbon fiber and epoxy resin. The adopted constraints for the design of new arms with different materials, non-conventional for these applications, are numerous. The new solutions must present a safety factor either with respect to the yield tensile strength or to the critical load of buckling greater than or equal to the one determined for the excavator in its original geometrical conformation. Another criterion, which has heavily conditioned the geometry of the arms, was given by the fact that the developed solutions must present a very similar value of the maximum displacement in the different load conditions analyzed. A new geometry for arms made by composite material was developed. It was an elliptical conic section, instead of the classic rectangular section, in order to use the filament winding technological process. As for the adoption of the composite material, we focused on the study and the design of this material as long as the interaction with the extremities (made of aluminum) which are interfaced either with the link between the arms or with the elements of the hydraulic plant which serves for the arms movement. From the results developed, it emerges that the solution developed by adopting composite materials is the one that permits the

The Advanced Technology Environmental Education Center Summer Fellows Institute.

Science.gov (United States)

Depken, Diane E.; Zeman, Catherine L.; Lensch, Ellen Kabat; Brown, Edward J.

2002-01-01

Describes the background, activities, and outcomes of the Advanced Technology Environmental Education Center (ATEEC) and its Summer Fellows Institutes as a model for disciplinary and cross-disciplinary infusion of environmental science and technology content, curriculum, and methods into the classroom. Presents experiences, themes, and activities…

Institute of Nuclear Chemistry and Technology annual report 1995

International Nuclear Information System (INIS)

1996-01-01

The report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology (INCT), Warsaw, in 1995. The papers are gathered in several branches as follows: radiation chemistry and physics (15); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (23); radiobiology (7); nuclear technologies and methods (21); nucleonic control systems (5). The Annual Report of INCT - 1995 contains also a general information about the staff and organization of the Institute, the full list of scientific publications and patents, conferences organized by INCT, thesis and list of projects granted by Polish and international organizations

Institute of Nuclear Chemistry and Technology annual report 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

The report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology (INCT), Warsaw, in 1995. The papers are gathered in several branches as follows: radiation chemistry and physics (15); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (23); radiobiology (7); nuclear technologies and methods (21); nucleonic control systems (5). The Annual Report of INCT - 1995 contains also a general information about the staff and organization of the Institute, the full list of scientific publications and patents, conferences organized by INCT, thesis and list of projects granted by Polish and international organizations.

Institute of Nuclear Chemistry and Technology annual report 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology (INCT), Warsaw, in 1995. The papers are gathered in several branches as follows: radiation chemistry and physics (15); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (23); radiobiology (7); nuclear technologies and methods (21); nucleonic control systems (5). The Annual Report of INCT - 1995 contains also a general information about the staff and organization of the Institute, the full list of scientific publications and patents, conferences organized by INCT, thesis and list of projects granted by Polish and international organizations.

Application of Strategic Institutional-Information Technology Alignment Model in Four-Year Institutions of Higher Education

Science.gov (United States)

Lach-Smith, Barbara

2010-01-01

This study examined an existing corporate model of business-information technology alignment for application in higher education and tested the findings by surveying executive and technology leaders in higher education. The purpose of this study was to gain a better understanding of the factors that impact alignment between institutional strategic…

Energy substrate used by workers of leaf-cutting ants during nest excavation

Directory of Open Access Journals (Sweden)

Roberto S. Camargo

2013-12-01

Full Text Available Energy substrate used by workers of leaf-cutting ants during nest excavation. In this study we aimed to ascertain whether leaf-cutting ant workers lose body reserves (fat or sugars as a function of nest excavation. For each treatment, we isolated 10 workers of Atta sexdens into two experimental groups, Control (C- without excavation and Soil (S- with excavation, which were kept for different time intervals (0, 24, 48 or 72 hours, totaling 700 tested workers. We then determined the concentration of soluble carbohydrates and total lipid content in them. The total carbohydrates were determined colorimetrically, based on the reaction between carbohydrates and sulfuric acid-phenol. For determination of lipids, the insects were immersed in organic solvent until they reached a constant weight. Our results showed that carbohydrates are consumed during nest excavation activities. In the experimental groups S24, S48 and S72, there was an average reduction of 5.82 (20.42%, 14.31 (44.96% and 13.27 (43.96% µ.mg-1 in soluble sugar when compared with the experimental groups that did not excavate. Furthermore, the lipids were not used during this activity. With respect to dry mass of the workers, their values were C0 = 8%, C24 = 10.4%, C48 = 9.2%, C72 = 10%, S24 = 9.2%, S48 = 8.7% and S72 = 8.5%. Our results show experimentally that the source of energy for nest excavation is carbohydrates, whereas lipids are conserved for other activities.

Excavations at Kainapirina (SAC), Watom Island, Papua New Guinea

International Nuclear Information System (INIS)

Green, R.C.; Anson, D.

1998-01-01

This paper is the final report on excavations in 1985 at the locality of Kainapirina (site SAC), situated on the Reber mission station adjacent to Rakival village on Watom Island. It backgrounds previous investigations there, the objectives of the 1985 endeavours, and the excavation strategies undertaken to achieve them. The occupation sequence based on stratigraphy, dating, and associated structural features is described and illustrated. Aspects of the human skeletal remains recovered are briefly reviewed; the economic evidence is discussed in detail. Analyses are provided of the various portable artefacts from these Lapita contexts, particularly stone adzes. obsidian, and pottery. These document an 'exotic to Watom' exchange component among the local manufactures. It is concluded that these 1985 excavations at SAC currently best enable an understanding of the significance of the entire Reber-Rakival Lapita site. (author)

Countermeasures planned for reducing water inflow into deep shafts at the Mizunami Underground Research Laboratory. Research for post-excavation grouting

International Nuclear Information System (INIS)

Kuji, Masayoshi; Matsui, Hiroya; Hara, Masato; Mikake, Shinichiro; Takeuchi, Shinji; Asai, Hideaki; Minamide, Masashi; Sato, Toshinori

2009-01-01

A large amount of water inflow is frequently occurs during the excavation of an underground cavern, such as road and railway tunnels, and underground electric facilities etc. The reduction of water inflow is sometimes quite important for the cost reduction for the water treatment and pumping during the construction of an underground cavern. The Mizunami Underground Research Laboratory (MIU) is currently being constructed by Japan Atomic Energy Agency. During its excavation, a large amount of water inflow into the shafts has been increasing and affecting the project progress. Therefore, a field experiment of post-excavation grouting around the Ventilation Shaft in a sedimentary formation carried out to confirm the effect of existing grouting technology for sedimentary formations in MIU project. The result shows that the applied methods in this field experiment are effective to prevent water inflow. This report describes the summary of the field experiment and the knowledge obtained through the experiment. (author)

Institute of Nuclear Chemistry and Technology annual report 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

This annual report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology, Warsaw, Poland in 1994. The papers are gathered into several branches as follows: radiation chemistry and physics (16 papers); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (17 papers); radiobiology (6 papers); nuclear technologies and methods (30 papers). The annual report of INCT-1994 contains also a general information about the Institute, the full list of papers published in 1994, information about Nukleonika - the International Journal of Nuclear Research being edited in INCT, the list of patent granted and patent applications in 1994, information about conferences organized by the Institute, the list of Ph.D. and D.Sc. finished in 1994 as well as the list of research projects and contracts being realized in INCT during 1994.

Institute of Nuclear Chemistry and Technology annual report 1994

International Nuclear Information System (INIS)

1995-01-01

This annual report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology, Warsaw, Poland in 1994. The papers are gathered into several branches as follows: radiation chemistry and physics (16 papers); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (17 papers); radiobiology (6 papers); nuclear technologies and methods (30 papers). The annual report of INCT-1994 contains also a general information about the Institute, the full list of papers published in 1994, information about Nukleonika - the International Journal of Nuclear Research being edited in INCT, the list of patent granted and patent applications in 1994, information about conferences organized by the Institute, the list of Ph.D. and D.Sc. finished in 1994 as well as the list of research projects and contracts being realized in INCT during 1994

Institute of Nuclear Chemistry and Technology annual report 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

This annual report is a collection of short communications being a review of scientific activity of the Institute of Nuclear Chemistry and Technology, Warsaw, Poland in 1994. The papers are gathered into several branches as follows: radiation chemistry and physics (16 papers); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (17 papers); radiobiology (6 papers); nuclear technologies and methods (30 papers). The annual report of INCT-1994 contains also a general information about the Institute, the full list of papers published in 1994, information about Nukleonika - the International Journal of Nuclear Research being edited in INCT, the list of patent granted and patent applications in 1994, information about conferences organized by the Institute, the list of Ph.D. and D.Sc. finished in 1994 as well as the list of research projects and contracts being realized in INCT during 1994.

Technology of silicon charged-particle detectors developed at the Institute of Electron Technology (ITE)

Science.gov (United States)

Wegrzecka, Iwona; Panas, Andrzej; Bar, Jan; Budzyński, Tadeusz; Grabiec, Piotr; Kozłowski, Roman; Sarnecki, Jerzy; Słysz, Wojciech; Szmigiel, Dariusz; Wegrzecki, Maciej; Zaborowski, Michał

2013-07-01

The paper discusses the technology of silicon charged-particle detectors developed at the Institute of Electron Technology (ITE). The developed technology enables the fabrication of both planar and epiplanar p+-ν-n+ detector structures with an active area of up to 50 cm2. The starting material for epiplanar structures are silicon wafers with a high-resistivity n-type epitaxial layer ( ν layer - ρ < 3 kΩcm) deposited on a highly doped n+-type substrate (ρ< 0,02Ωcm) developed and fabricated at the Institute of Electronic Materials Technology. Active layer thickness of the epiplanar detectors (νlayer) may range from 10 μm to 150 μm. Imported silicon with min. 5 kΩcm resistivity is used to fabricate planar detectors. Active layer thickness of the planar detectors (ν) layer) may range from 200 μm to 1 mm. This technology enables the fabrication of both discrete and multi-junction detectors (monolithic detector arrays), such as single-sided strip detectors (epiplanar and planar) and double-sided strip detectors (planar). Examples of process diagrams for fabrication of the epiplanar and planar detectors are presented in the paper, and selected technological processes are discussed.

Institut čistých technologií

Czech Academy of Sciences Publication Activity Database

Šňupárek, Richard

2014-01-01

Roč. 2014, č. 6 (2014), s. 28-29 ISSN 1210-9525 R&D Projects: GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : clean technologies * research project * energetical materials Subject RIV: JQ - Machines ; Tools http://abicko.avcr.cz/2014/06/09/index.html

Investigation of Hexavalent Chromium Flux to Groundwater at the 100-C-7:1 Excavation Site

Energy Technology Data Exchange (ETDEWEB)

Truex, Michael J.; Vermeul, Vincent R.; Fritz, Brad G.; Mackley, Rob D.; Horner, Jacob A.; Johnson, Christian D.; Newcomer, Darrell R.

2012-11-16

Deep excavation of soil has been conducted at the 100-C-7 and 100-C-7:1 waste sites within the 100-BC Operable Unit at the Department of Energy (DOE) Hanford Site to remove hexavalent chromium (Cr(VI)) contamination with the excavations reaching to near the water table. Soil sampling showed that Cr(VI) contamination was still present at the bottom of the 100-C-7:1 excavation. In addition, Cr(VI) concentrations in a downgradient monitoring well have shown a transient spike of increased Cr(VI) concentration following initiation of excavation. Potentially, the increased Cr(VI) concentrations in the downgradient monitoring well are due to Cr(VI) from the excavation site. However, data were needed to evaluate this possibility and to quantify the overall impact of the 100-C-7:1 excavation site on groundwater. Data collected from a network of aquifer tubes installed across the floor of the 100-C-7:1 excavation and from temporary wells installed at the bottom of the entrance ramp to the excavation were used to evaluate Cr(VI) releases into the aquifer and to estimate local-scale hydraulic properties and groundwater flow velocity.

Fifty years experiences in nuclear engineering education at Tokyo Institute of Technology

International Nuclear Information System (INIS)

Fujii, Yasuhiko; Saito, Masaki; Aritomi, Masanori

2008-01-01

Nuclear engineering education has been initiated in 1957 at the graduate school of Tokyo Institute of Technology. Educational activities have been conducted for fifty years under the support of the Research Laboratory for Nuclear Reactors. In the past fifty years, about 1000 Master students and 200 Doctoral students and 200 Doctoral students graduated from our Nuclear Engineering Department at Tokyo Institute of Technology. Many of them found their jobs in nuclear industries and institutes. International course of nuclear engineering was initiated in 1994, and so far about 90 students from 15 overseas countries have graduated from our Master and Doctoral Programs. In 2003, our proposal of 'Innovative Nuclear Energy System for the Sustainable World' was adopted as the Center of Excellent Program sponsored by Ministry of Education, Science and Technology. Recently a collaborative education network has been developed among Kanazawa University, Fukui University, Ibaraki University, Okayama University, Tokyo Institute of Technology and Japan Atomic Energy Agency. (author)

A Basic Robotic Excavator (the Glenn Digger): Description, Design, and Initial Operation

Science.gov (United States)

Bauman, Steve; Newman, Paul; Izadnegahdar, Alain; Johnson, Kyle; Abel, Phillip

2016-01-01

This paper describes the design, commercial part selections, fabrication, assembly, installation, and initial operation of a two degree of freedom robotic excavator. Colloquially referred to as "the NASA Glenn Digger," it was designed specifically to be mounted onto, and to operate with, the then newly developed Centaur 2 robotic mobility base. The excavator, when mounted to Centaur 2, is designed to scoop loose regolith from the terrain, raise its loaded bucket up and dump the load into a hopper of at least a 1-m-height. The hopper represents the input to a machine that would process the raw material, such as to produce oxygen from lunar regolith as would be required for long-term lunar habitation. This equipment debuted at the annual Research and Technology Studies ("Desert RATS", Ref. 1) event held north of Flagstaff, Arizona, in September of 2010, when the Digger was successfully joined to Centaur 2 and the shoveling articulation was demonstrated. During 2011, the hardware was modified for added strength, strain gauges were added to measure loads, and the controls were improved in preparation for the 2011 Desert RATS event, where additional "field operations" experience was gained.

Bucket wheel excavators for open-cast mining all over the world

Energy Technology Data Exchange (ETDEWEB)

Durst, W.

1979-04-01

A report is given on the use of bucket wheel excavators, spreaders and tripper cars in open-cast mining of brown coal, oilsand and other minerals in Australia, Canada, India, Spain, USA and Yugoslavia as well as on the use of bucket wheel excavators for land reclamation in Singapore.

Estimating RMR Values for Underground Excavations in a Rock Mass

Directory of Open Access Journals (Sweden)

Vítor Santos

2018-02-01

Full Text Available During underground excavations for civil or mining engineering purposes, the variations in rock mass quality are important, especially for the design of the most suitable support to be applied to ensure stability. The aim of this investigation is to model the expected behavior of the ground, and thus to predict the scenarios indicating potential variations in the quality of the rock mass during underground excavation. When considering the rock mass rating (RMR values observed at the excavation face in six study cases, which together total more than 27 km in length of underground excavation by drilling and blasting (D&B, and based on the observed RMR values at the face, the most probable value (1–100 is estimate for the RMR index at the five subsequent front advances. It is concluded that, up to about 20 m ahead of the current face, the quality of the rock mass for the next advances is close to the quality observed at the present face, and that, with increasing distance, there is a greater deviation of RMR values with respect to the quality observed at the current face.

The performing interaction between institutions and technology in the French electronuclear industry

International Nuclear Information System (INIS)

Finon, D.; Staropoli, C.

2000-10-01

Among the various traditional ''grands programmes'' typical of the French public intervention in high-tech industries, the nuclear programme is often considered as one of the major successes. However in recent years, the French national nuclear system, as composed of the whole set of institutions and relations between organisations in this sector, is affected by different exogenous shocks. In disorder those shocks are the European power markets liberalization legislation, the persistence of the world-wide nuclear market depression, the competition of a new power generation technology (gas turbine), and the globalization and concentration of the world-wide electromechanical industry. So, in the power industry of many OECD countries, the social acceptance crisis of nuclear technology as well as the emergence of the much less capital-intensive gas turbine relax the co-determination and open up the institutional choice. Conversely, in France, the performances of the nuclear program help to maintain the nuclear option, thus justifying the preservation of the existing industrial organisation and institutional scheme. In order to characterise the joint institutional and technological dynamics of the French electricity supply industry two stages are distinguished and discussed: first the efficient adaptation of institutions and industrial relationships to the nuclear as a new technology, and second the influence of technological features on the industry structures changes. (A.L.B.)

The performing interaction between institutions and technology in the French electronuclear industry

Energy Technology Data Exchange (ETDEWEB)

Finon, D.; Staropoli, C

2000-10-01

Among the various traditional ''grands programmes'' typical of the French public intervention in high-tech industries, the nuclear programme is often considered as one of the major successes. However in recent years, the French national nuclear system, as composed of the whole set of institutions and relations between organisations in this sector, is affected by different exogenous shocks. In disorder those shocks are the European power markets liberalization legislation, the persistence of the world-wide nuclear market depression, the competition of a new power generation technology (gas turbine), and the globalization and concentration of the world-wide electromechanical industry. So, in the power industry of many OECD countries, the social acceptance crisis of nuclear technology as well as the emergence of the much less capital-intensive gas turbine relax the co-determination and open up the institutional choice. Conversely, in France, the performances of the nuclear program help to maintain the nuclear option, thus justifying the preservation of the existing industrial organisation and institutional scheme. In order to characterise the joint institutional and technological dynamics of the French electricity supply industry two stages are distinguished and discussed: first the efficient adaptation of institutions and industrial relationships to the nuclear as a new technology, and second the influence of technological features on the industry structures changes. (A.L.B.)

Dig-face monitoring during excavation of a radioactive plume at Mound Laboratory, Ohio

International Nuclear Information System (INIS)

Josten, N.E.; Gehrke, R.J.; Carpenter, M.V.

1995-12-01

A dig-face monitoring system consists of onsite hardware for collecting information on changing chemical, radiological, and physical conditions in the subsurface soil during the hazardous site excavation. A prototype dig-face system was take to Mount Laboratory for a first trial. Mound Area 7 was the site of historical disposals of 232 Th, 227 Ac, and assorted debris. The system was used to monitor a deep excavation aimed at removing 227 Ac-contaminated soils. Radiological, geophysical, and topographic sensors were used to scan across the excavation dig-face at four successive depths as soil was removed. A 3-D image of the contamination plumes was developed; the radiation sensor data indicated that only a small portion of the excavated soil volume was contaminated. The spatial information produced by the dig-face system was used to direct the excavation activities into the area containing the 227 Ac and to evaluate options for handling the separate 232 Th plume

Numerical study on lateral wall displacement of deep excavation supported by IPS earth retention system

Directory of Open Access Journals (Sweden)

Tugen Feng

2017-12-01

Full Text Available The objective of this study is to investigate the 3D behavior characteristics of an excavation supported by an innovative prestressed support (IPS earth retention system. A numerical simulation was conducted in order to provide insight into the IPS system behavior by using the FLAC3D package. Prior to the parametric study, validation work was conducted by means of a comparison of the deformation between the field test data and numerical analysis results, and strong agreement was obtained. The reasonable excavation location, layered excavation thickness, and blocked excavation sequence are presented according to variable parameter analysis. In view of the previous findings, certain measurements are proposed in order to control the foundation pit deformation. The results indicate that prestress compensation has a significant effect on the IPS system behavior, while an optimized excavation sequence slightly improves its behavior. With the conclusion proposed based on the numerical results, the aim is to provide reference data for optimization design and the construction sequence. Keywords: FLAC3D, IPS system, Prestress compensation, Layered excavation, Blocked excavation, Deformation control

Controlled drill ampersand blast excavation at AECL's Underground Research Laboratory

International Nuclear Information System (INIS)

Kuzyk, G.W.; Onagi, D.P.; Thompson, P.M.

1996-01-01

A controlled drill and blast method has been developed and used to excavate the Underground Research Laboratory, a geotechnical facility constructed by Atomic Energy of Canada Limited (AECL) in crystalline rock. It has been demonstrated that the method can effectively reduce the excavation disturbed zone (EDZ) and is suitable for the construction of a used fuel disposal vault in the plutonic rock of the Canadian Shield

Silica exposure to excavation workers during the excavation of a low level radiological waste pit and tritium disposal shafts

International Nuclear Information System (INIS)

Wilson, K.M.

1995-01-01

This study evaluated the task-length average (TLA) respirable dust and respirable silica airborne concentrations to which construction workers excavating volcanic tuff at Los Alamos National Laboratory (LANL) were exposed. These workers were excavating a low level radiological waste disposal pit of final dimensions 720 feet long, 132 feet wide and 60 feet deep. The objectives of this study were as follows: (1) evaluate exposures; (2) determine if the type of machinery used affects the respirable dust concentration in the breathing zone of the worker; (3) evaluate the efficacy of wetting the pit to reduce the respirable dust exposure; and (4) determine if exposure increases with increasing depth of pit due to the walls of the pit blocking the cross wind ventilation

Study on construction technology for repository

International Nuclear Information System (INIS)

Tanai, Kenji; Iwasa, Kengo; Hasegawa, Hiroshi; Miura, Kazuhiko; Okutsu, Kazuo; Kobayashi, Masaaki

1999-11-01

For the construction of underground facilities comprising access tunnels, connecting tunnels, main tunnels and disposal tunnels, a large number of tunnels will be excavated in deep rock formations. These excavations will extend hundreds kilometers in total length. Therefore, special attention must be paid, to transporting large volume of debris, ventilation, emergency escape routes in case of accident, and other factors. In addition, special attention must also paid to potential accidents which might in underground excavations, including unstable facing phenomena (such as collapse and swelling of facing at weak layer sections), spring water flow resulting collapse of rock, gas eruption, and rock burst. While considering these factors to be emphasized during the construction of geological disposal facilities, the investigation reviewed the existing working methods on individual construction technologies of access tunnels, main tunnels, connecting tunnels, disposal tunnels, and disposal pit, based on the recognition that the present state deals with a wide range of geological environments, and conducted investigation about the construction methods for each tunnel on the basis current technologies, and described the outline of these methods. Furthermore, for the items to be particularly emphasized on site characterization and siting data such as ground pressure and spring water, the investigation reviewed the current countermeasure works, and made survey on the phenomena appeared during actual tunnel construction works and their countermeasures, and carried out a study on effectiveness of these countermeasures. This constructing of disposal site in deep geological formations is basically possible by applying, or confirming, current excavation technologies for tunnels and underground facilities. A systematic construction system combines separate technologies relating to construction, (excavation technology, tunnel support work method, etc.). Such systems can be

ORGANISATIONAL-TECHNOLOGICAL CHARACTERISTICS OF BLASTING WORKS ON THE GRIČ TUNNEL

Directory of Open Access Journals (Sweden)

Zvonimir Deković

2005-12-01

Full Text Available The paper describes organisational-technological characteristics of blasting works during the excavation of the Grič Tunnel. The significance of blasting works during the excavation of the tunnel is shown through adjustment of blasting parameters taking into consideration the dynamics of the works, cost-effectiveness and influence of geological circumstances. Successfulness of blasting directly influences the subsequent tunnel excavation cycle both in terms of duration as well as eventually in terms of influence on the entire tunnel investment. Comparison of changes of basic blasting parameters during tunnel excavation ensured optimal excavation progress with minimal price per meter of tunnel progress.

29 CFR 1926.913 - Blasting in excavation work under compressed air.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Blasting in excavation work under compressed air. 1926.913... Use of Explosives § 1926.913 Blasting in excavation work under compressed air. (a) Detonators and... connecting wires are connected up. (b) When detonators or explosives are brought into an air lock, no...

Annual report of Institute of Nuclear Chemistry and Technology 1996

International Nuclear Information System (INIS)

1997-06-01

The report is a collection of short communications being a review of the scientific activities of the Institute of Nuclear Chemistry and Technology, Warsaw in 1996. The papers are gathered in several branches as follows: radiation chemistry and physics (17); Radiochemistry, stable isotopes, nuclear analytical methods,chemistry in general (20); radiobiology (9); nuclear technologies and methods (28).The last and biggest chapter has been divided in four smaller groups; process engineering; material engineering,structural studies,diagnostics; radiation technologies; nucleonic control systems. The annual report of INCT-1996 contains also a general information of Institute, the full list of scientific publications and patents, conferences organized by INCT, Ph.D. and D.Sc. thesis, a list of projects granted by Polish Committee of Scientific Research and other organizations

Annual report of Institute of Nuclear Chemistry and Technology 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The report is a collection of short communications being a review of the scientific activities of the Institute of Nuclear Chemistry and Technology, Warsaw in 1996. The papers are gathered in several branches as follows: radiation chemistry and physics (17); Radiochemistry, stable isotopes, nuclear analytical methods,chemistry in general (20); radiobiology (9); nuclear technologies and methods (28).The last and biggest chapter has been divided in four smaller groups; process engineering; material engineering,structural studies,diagnostics; radiation technologies; nucleonic control systems. The annual report of INCT-1996 contains also a general information of Institute, the full list of scientific publications and patents, conferences organized by INCT, Ph.D. and D.Sc. thesis, a list of projects granted by Polish Committee of Scientific Research and other organizations.

Electron beam facilities and technologies developed in the Institute of Nuclear Chemistry and Technology

International Nuclear Information System (INIS)

Chmielewski, A.G.; Walis, L.; Zimek, Z.

1992-01-01

The operation of the first electron accelerator has been started at Institute /former Institute for Nuclear Research/ in 1971. This LAE-13/9 accelerator is a two-section lineac with adjustable energy of electrons: 5 to 13 MeV and the beam power up to 9 kW. The main technologies developed on the basis of LAE-13/9 are: sterilization, manufacturing of thermoshrinkable materials and modification of semiconductors. The accelerator is operated 4000 hours per year and used for small scale production and services in these fields. The other problems investigated in laboratory scale are: food preservation and hygenization, hygenization of municipal sewage sludge, and bio-conversion of pig-farm wastes into animal fodder. The laboratory experiments are basis for pilot construction and other industrial applications. The mentioned technology of thermoshrinkable tube production was implemented in industrial scale at ZWUT Czluchow which factory is equipped in the accelerator ILU-6 /20 kW, 2 MeV/. On the basis of similar unit a technological installation was built at Institute. The plant is furnished with a conveyer and the rewinding machines for tubes and tapes manufacturing. This allows continuous production of these materials. The plant will start operation next year and linear accelerator /10 MeV, 15 kW/ for this purpose is already delivered. The pilot plant for food preservation and hygenization has been built. It is equipped in small pilot accelerator 10 MeV, 1 kW and will be furnished with 10 MeV, 10 kW lineac this year. Beside of this technological lines Institute is furnished in Van de Graff accelerator /2, MeV, 100 μA/ and another laboratory unit LAE-10 /10 MeV, 10-100 ns 2 us/ is under construction. (J.P.N.)

Stepwise excavation in a permanent molar

DEFF Research Database (Denmark)

Lima, Fernanda Ferruzzi; Pascotto, Renata Corrêa; Benetti, Ana Raquel

2010-01-01

with zinc oxide cement were performed to minimize the risk of pulp exposure during excavation. After 45 days, the remaining carious tissue was removed and a restoration with glass-ionomer lining (Vitrebond) and resin composite (P-50) was performed. Satisfactory morphology and function of the restoration...

Implementation of the e-learning method for technological research institutes utilization

International Nuclear Information System (INIS)

Pinheiro, Valderes Fernandes; Silva, Aucyone Augusto da; Rogero, Jose Roberto

2002-01-01

The e-learning is a subject that is attracting all teaching institution at the present because the number of interested student is growing in the same proportion of communication technology facilities is getting more easy and low cost to be used. Most of universities and colleges are adapting their classes to on-line and a new market is growing very fast all around the world. Of course that these institutions are also worried about the quality of the online teaching materials and also methodologies used to delivery them. This paper will explore some models that are being used in online classes and also will present the contribution of this research in developing a new teaching model that will applied in the technological research institutions like IPEN/CNEN-SP. This model should be technical and economical self-sufficient and it is emphasized in the customers technological needs. The model's variables are interactivity levels with the technology, use of internet tools (chat, forum, discussion list), teacher and student relationship, knowledge evaluation, etc. (author)

Integration of learning technologies into teaching within Fijian Polytechnic Institutions

Directory of Open Access Journals (Sweden)

Shalendra Kumar

2016-11-01

Full Text Available Abstract In the 21st century, learning technologies have increasingly become pervasive within various forms of learning environments. Institutions of higher education are increasingly turning to these technologies to resource and support their teaching and learning environments under distributed circumstances, face-to-face or blended. Recently, the Fijian Ministry of Education systematically introduced learning technologies into Fiji’s technical colleges to support teaching and learning. However, prior to the widespread deployment of these technologies, little information was available on educators’ perception of the value of these technologies, and the extent to which this could influence adoption. The purpose of this study was to gain a better understanding of lecturers’ perceptions of the value of learning technologies and factors likely to influence their decisions to adopt and integrate these technologies into teaching as well as challenges they are likely to face. A survey was administered to fifty five self-selected lecturers involved in teaching within three Polytechnics in Fiji. Although overall findings suggested that lecturers strongly valued the contribution of learning technologies in enhancing student learning, a number of factors likely to influence the rapid adoption of these technologies were identified. These included attitude towards technology and perceived usefulness of technology in teaching, the institutional cultural environment, as well as resources available to support uptake. This research contributes to the growing significance of individual, contextual and cultural influences in the adoption of learning technologies into teaching.

Hard rock excavation at the CSM/OCRD test site using Swedish blast design techniques

International Nuclear Information System (INIS)

Holmberg, R.

1983-09-01

This report is the third in a series describing research conducted by the Colorado School of Mines for the Office of Crystalline Repository Development (OCRD) to determine the extent of blast damage in rock surrounding an underground opening. A special room, called the CSM/OCRD room, was excavated at the CSM experimental mine for the purpose of assessing blast damage in the rock around the room. Even though this mine is not proposed as a nuclear waste repository site, the instrumentation and methods of blast damage assessment developed in this project are applicable to proposed repository sites. This report describes the application of Swedish blasting technology for the excavation of the test room. The design of the blasting patterns including the selection of explosives, hole sizes and location, explosive loading densities, and delay intervals is based upon the theories of Langefors and Kihlstrom in combination with methods used at the Swedish Detonic Research Foundation for minimizing unwanted rock damage. The practical application of the design procedures to seven rounds and the achieved results is discussed

Calculation of the Chilling Requirement for Air Conditioning in the Excavation Roadway

Directory of Open Access Journals (Sweden)

Yueping Qin

2015-10-01

Full Text Available To effectively improve the climate conditions of the excavation roadway in coal mine, the calculation of the chilling requirement taking air conditioning measures is extremely necessary. The temperature field of the surrounding rock with moving boundary in the excavation roadway was numerically simulated by using finite volume method. The unstable heat transfer coefficient between the surrounding rock and air flow was obtained via the previous calculation. According to the coupling effects of the air flow inside and outside air duct, the differential calculation mathematical model of air flow temperature in the excavation roadway was established. The chilling requirement was calculated with the selfdeveloped computer program for forecasting the required cooling capacity of the excavation roadway. A good air conditioning effect had been observed after applying the calculated results to field trial, which indicated that the prediction method and calculation procedure were reliable.

Energy-saving analysis of hydraulic hybrid excavator based on common pressure rail.

Science.gov (United States)

Shen, Wei; Jiang, Jihai; Su, Xiaoyu; Karimi, Hamid Reza

2013-01-01

Energy-saving research of excavators is becoming one hot topic due to the increasing energy crisis and environmental deterioration recently. Hydraulic hybrid excavator based on common pressure rail (HHEC) provides an alternative with electric hybrid excavator because it has high power density and environment friendly and easy to modify based on the existing manufacture process. This paper is focused on the fuel consumption of HHEC and the actuator dynamic response to assure that the new system can save energy without sacrificing performance. Firstly, we introduce the basic principle of HHEC; then, the sizing process is presented; furthermore, the modeling period which combined mathematical analysis and experiment identification is listed. Finally, simulation results show that HHEC has a fast dynamic response which can be accepted in engineering and the fuel consumption can be reduced 21% to compare the original LS excavator and even 32% after adopting another smaller engine.

The Role of Technology and Institutions for Growth

DEFF Research Database (Denmark)

Henriksen, Ingrid; Lampe, Markus; Sharp, Paul

We consider the relative contributions of changing technology and institutions for economic growth through the investigation of a natural experiment in history: the almost simultaneous introduction of the automatic cream separator and the cooperative ownership form in the Danish dairy industry fr...

Nest enlargement in leaf-cutting ants: relocated brood and fungus trigger the excavation of new chambers.

Directory of Open Access Journals (Sweden)

Daniela Römer

Full Text Available During colony growth, leaf-cutting ants enlarge their nests by excavating tunnels and chambers housing their fungus gardens and brood. Workers are expected to excavate new nest chambers at locations across the soil profile that offer suitable environmental conditions for brood and fungus rearing. It is an open question whether new chambers are excavated in advance, or will emerge around brood or fungus initially relocated to a suitable site in a previously-excavated tunnel. In the laboratory, we investigated the mechanisms underlying the excavation of new nest chambers in the leaf-cutting ant Acromyrmex lundi. Specifically, we asked whether workers relocate brood and fungus to suitable nest locations, and to what extent the relocated items trigger the excavation of a nest chamber and influence its shape. When brood and fungus were exposed to unfavorable environmental conditions, either low temperatures or low humidity, both were relocated, but ants clearly preferred to relocate the brood first. Workers relocated fungus to places containing brood, demonstrating that subsequent fungus relocation spatially follows the brood deposition. In addition, more ants aggregated at sites containing brood. When presented with a choice between two otherwise identical digging sites, but one containing brood, ants' excavation activity was higher at this site, and the shape of the excavated cavity was more rounded and chamber-like. The presence of fungus also led to the excavation of rounder shapes, with higher excavation activity at the site that also contained brood. We argue that during colony growth, workers preferentially relocate brood to suitable locations along a tunnel, and that relocated brood spatially guides fungus relocation and leads to increased digging activity around them. We suggest that nest chambers are not excavated in advance, but emerge through a self-organized process resulting from the aggregation of workers and their density

Report on surveys and researches to excavate international joint researches related to industrial technologies; Sangyo gijutsu ni kansuru kokusai kyodo kenkyu hakkutsu no tame no chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Five themes were taken up for a project of the 'surveys and researches to excavate international joint researches related to industrial technologies'. Investigation groups were organized and dispatched for each theme toperform domestic and overseas surveys. Discussions were given on eachtheme for the possibilities of structuring international joint researches. The five themes are as follows: 'wearable information network related technologies', wherein technologies to micronize information devices have been advanced rapidly, and the technologies are entering the age from personalizing and mobilizing the information into the wearable computing; this theme is intended to develop systems to unify these technologies by means of international joint researches: 'surveys on using unutilized animal oils and fats as chemical raw materials', which are intended to make clear possibilities and problems in utilizing animal oils and fats as raw materials for the chemical industry that can substitute fossil resources: 'international joint researches on new glasses' and 'processes to manufacture semiconductors using glassy carbon' to develop glassy carbon having excellent chemical resistance substituting quartz: and 'international joint researches on the Russian project which places environment and energy in its center'. (NEDO)

Studies on engineering technologies in the Mizunami Underground Research Laboratory. FY 2007 (Contract research)

International Nuclear Information System (INIS)

Noda, Masaru; Suyama, Yasuhiro; Nobuto, Jun; Ijiri, Yuji; Mikake, Shinichiro; Matsui, Hiroya

2009-07-01

The Mizunami Underground Research Laboratory (MIU) of the Japan Atomic Energy Agency is a major site for geoscientific research to advance the scientific and technological basis for geological disposal of high-level radioactive waste in crystalline rock. Studies on relevant engineering technologies in the MIU consist of a) research on design and construction technology for very deep underground applications, and b) research on engineering technology as a basis of geological disposal. In the Second Phase of the MIU project (the construction phase), engineering studies have focused on research into design and construction technologies for deep underground. The main subjects in the study of very deep underground structures consist of the following: 'Demonstration of the design methodology', 'Demonstration of existing and supplementary excavation methods', 'Demonstration of countermeasures during excavation' and 'Demonstration of safe construction'. In the FY 2007 studies, identification and evaluation of the subjects for study of engineering technologies in the construction phase were carried out to optimize future research work. Specific studies included: validation of the existing design methodology based on data obtained during construction; validation of existing and supplementary rock excavation methods for very deep shafts; estimation of rock stability under high differential water pressures, methodology on long-term maintenance of underground excavations and risk management systems for construction of underground structures have been performed. Based on these studies, future research focused on the four subject areas, which are 'Demonstration of the design methodology', 'Demonstration of existing and supplementary excavation methods', 'Demonstration of countermeasures during excavation' and 'Demonstration of safe construction', has been identified. The design methodology in the first phase of the MIU Project (surface-based investigation phase) was verified to

Radiological safety research for nuclear excavation projects - Interoceanic canal studies

Energy Technology Data Exchange (ETDEWEB)

Klement, Jr, A W [U.S. Atomic Energy Commission, Las Vegas, NV (United States)

1969-07-01

The general radiological problems encountered in nuclear cratering and nuclear excavation projects are discussed. Procedures for assessing radiological problems in such projects are outlined. Included in the discussions are source term, meteorology, fallout prediction and ecological factors. Continuing research requirements as well as pre- and post-excavation studies are important considerations. The procedures followed in the current interoceanic canal feasibility studies provide examples of radiological safety problems, current solutions and needed research. (author)

Radiological safety research for nuclear excavation projects - Interoceanic canal studies

International Nuclear Information System (INIS)

Klement, A.W. Jr.

1969-01-01

The general radiological problems encountered in nuclear cratering and nuclear excavation projects are discussed. Procedures for assessing radiological problems in such projects are outlined. Included in the discussions are source term, meteorology, fallout prediction and ecological factors. Continuing research requirements as well as pre- and post-excavation studies are important considerations. The procedures followed in the current interoceanic canal feasibility studies provide examples of radiological safety problems, current solutions and needed research. (author)

Study on engineering technologies in the Mizunami Underground Research Laboratory (FY 2015). Development of design and construction planning and countermeasure technologies (Contract research)

International Nuclear Information System (INIS)

Toguri, Satohito; Kobayashi, Shinji; Tsuji, Masakuni; Yahagi, Ryoji; Yamada, Toshiko; Matsui, Hiroya; Mikake, Shinichiro; Aoyagi, Yoshiaki; Sato, Toshinori

2017-03-01

The study on engineering technology in the Mizunami Underground Research Laboratory (MIU) project roughly consists of (1)development of design and construction planning technologies, (2)development of construction technology, (3)development of countermeasure technology, (4)development of technology for security, and (5) development of technologies regarding restoration and mitigating of the excavation effect. So far, the verification of the initial design based on the data obtained during excavation was mainly conducted as a research in the Construction Phase, also the countermeasure technologies to control groundwater inflow were examined as a research in the Operation Phase. In FY2015, as a part of the important issues on the research program, “Development of countermeasure technologies for reducing groundwater inflow” in the Japan Atomic Energy Agency 3rd Midterm Plan, water-tight grouting method has been developed. Grouting methods utilized in the MIU were evaluated and the post-excavation grouting at the -500m Access/Research Gallery-South was planned based on these evaluation results. Also, technology development from the viewpoint of geological disposal was summarized, and information on the alternative method to the grouting method was collected and organized. (author)

How and Why Higher Education Institutions Use Technology in Developmental Education Programming. A CAPR Working Paper

Science.gov (United States)

Natow, Rebecca S.; Reddy, Vikash; Grant, Markeisha

2017-01-01

As postsecondary institutions increasingly integrate technology into developmental education, it becomes important to understand how technology is used in these programs, what challenges institutions have encountered relating to the technology, and what considerations institutional leaders take into account when deciding whether and how to…

Summary report of soil removal preliminary excavations. (Report No. ES-389-75-171)

International Nuclear Information System (INIS)

Wickland, C.E.

1975-07-01

A proposed technique to remove small areas, 2 , of contaminated soil is discussed along with the results of an actual excavation. Based on the results of a trial excavation in uncontaminated soil and an excavation of two trenches in contaminated soil, it is concluded that the techniques described are a satisfactory means of contaminated soil removal. It can be done safely with a release of airborne plutonium a factor of 10 or more below the Environmental Protection Administration (EPA) limit

Supplier strategies and responses to institutional drivers for an emerging energy technology

International Nuclear Information System (INIS)

Strachan, N.; Dowlatabadi, H.

2004-01-01

This paper investigates the role of suppliers of a new energy technology, when the market for that technology continues to be in a state of flux, and is characterised by continued regulatory and institutional developments. This paper first summarises the institutional drivers resulting in the widely divergent diffusion of distributed generation (DG) based on natural gas engines in the Netherlands and the UK. Then, supplier responses to this institutionally driven market are discussed. Under regulatory support, supply firms were able to implement innovative operational and ownership arrangements, hugely growing the market while positioning themselves for new R and D and market developments. Under regulatory restrictions, supply firms fought to survive, with resultant implications for the reputation and longer term prospects for this new energy technology. The paper concludes by discussing how continuing institutional instability can limit the supplier strategies based on spillovers from successful regulatory experiments, Thus, the establishment of a viable energy supply industry is delayed under continuing regulatory uncertainty. (author)

Excavating a transfer tunnel

CERN Multimedia

Laurent Guiraud

2000-01-01

The transfer tunnel being dug here will take the 450 GeV beam from the SPS and inject it into the LHC where the beam energies will be increased to 7 TeV. In order to transfer this beam from the SPS to the LHC, two transfer tunnels are used to circulate the beams in opposite directions. When excavated, the accelerator components, including magnets, beam pipes and cryogenics will be installed and connected to both the SPS and LHC ready for operation to begin in 2008.

Numerical simulation of excavation and supporting of pit slope of the pump room in XNPC

International Nuclear Information System (INIS)

Hu Mengqian; Zhu Xiuyun; Ji Zhonghua; Lu Yu; Sun Feng

2014-01-01

The research simulates the excavation and supporting of pit slope of the pump room in XNPC. According to the designing of excavation and supporting plan of slope, the numerical simulation of excavation and supporting of pit slope is conducted using the ANSYS finite element numerical simulation software. The simulation results show that, the displacement and stress caused by the excavation of above stage slope and pit slope are both small after taking some measures, including deep mixing pile reinforcement, retaining piles and prestressed anchor cable. Thus the slope is steady. (authors)

Technological capabilities, institutions and firm productivity: a multilevel study

Czech Academy of Sciences Publication Activity Database

Goedhuys, M.; Srholec, Martin

2015-01-01

Roč. 27, č. 1 (2015), s. 122-139 ISSN 0957-8811 Institutional support: PRVOUK-P23 Keywords : productivity * innovation * technological capability Subject RIV: AH - Economics Impact factor: 0.720, year: 2015

Chip shape and secondary fragmentation through TBM excavation

International Nuclear Information System (INIS)

Tsusaka, Kimikazu; Tanimoto, Chikaosa; Ueno, Takaaki; Koizumi, Yu; Nakane, Tatsuto

2008-01-01

The chips through TBM tunneling are well-known for one of useful indices to reflect the geological conditions. The flat and elongated chips whose width are equal to the spacing of cutter trace indicate the cutting face with less joints and good practice of TBM excavation with less secondary fragmentation rate. Through a case history in granitic rock, the authors proposed the new index, which is the ratio of length of major axis to thickness. Also the authors studied the relationship between the index and the excavation efficiencies. In conclusion, it was clarified that chips with the new index over 3.5 were generally observed when a TBM drove with less than 30% the secondary fragmentation rate. (author)

Modeling and stability of electro-hydraulic servo of hydraulic excavator

Science.gov (United States)

Jia, Wenhua; Yin, Chenbo; Li, Guo; Sun, Menghui

2017-11-01

The condition of the hydraulic excavator is complicated and the working environment is bad. The safety and stability of the control system is influenced by the external factors. This paper selects hydraulic excavator electro-hydraulic servo system as the research object. A mathematical model and simulation model using AMESIM of servo system is established. Then the pressure and flow characteristics are analyzed. The design and optimization of electro-hydraulic servo system and its application in engineering machinery is provided.

Deformations and damage to buildings adjacent to deep excavations in soft soils

NARCIS (Netherlands)

Korff, M.

2009-01-01

The objective of this study is to gain insight into mechanisms of soil-structure interaction for buildings adjacent to deep excavations and to find a reliable method to design and monitor deep excavations in urban areas with soft soil conditions. The research focuses on typical Dutch conditions. The

The huge ATLAS cavern now fully excavated

CERN Multimedia

2002-01-01

Excavation of the ATLAS cavern is now complete! At the end of two years' work involving a tremendous technical challenge, the civil engineering contractors have succeeded in digging out one of the biggest experimental caverns in the world. Bravo!

Excavated pulmonary nodules: an unusual clinical presentation of lung metastasis in two cases

Directory of Open Access Journals (Sweden)

Lalya Issam

2010-06-01

Full Text Available Abstract Background Excavated pulmonary metastasis are rare. We present two cases of excavated pulmonary nodules proved to be metastases from osteosarcoma and gallblader lymphoma. Case presentation The first one is 39-year-old man in whom cholecystectomy made the diagnosis of primary non-Hodgkin's lymphoma of the gallbladder. He presented in chest CT scan excavated nodules that had been biopsied and confirmed the diagnosis of non hodgkin lymphoma. He underwent 8 courses of chemotherapy CHOP 21 with complete remission. The second one is an 21 years old man who presented a right leg osteoblastic osteosarcoma with only excavated pulmonary nodules in extension assessment. He had 3 courses of polychemotherapy API (doxorubicin, platinum, and ifosfamide with partial response. Unfortunately, he died following a septic shock. Review of the literature shows that excavated pulmonary nodules as metastasis are rare but we should consider this diagnosis every time we are in front of a cancer. Chest computed tomography is the best diagnosis imaging that could make this diagnosis. Differential diagnosis between benign and malignant bullous lesions is important because surgical excision affects survival in some malignancies. Conclusions Although pulmonary nodules are the most common cancer metastasis, a differential diagnosis of a concurrent primary malignancy should always be considered every time we have excavated lesions, even in patients with known malignant disease. Thorough chest evaluation is important, as multiple primary malignancies may occur concomitantly.

Touch Screen Technology Adoption and Utilisation by Educators in Early Childhood Educational Institutions

DEFF Research Database (Denmark)

Plumb, Melinda; Kautz, Karlheinz; Tootell, Holly

2013-01-01

The adoption of information and communication technology (ICT) in early childhood educational settings, in particular touch screen technology such as interactive whiteboards and tablet computing devices has potential for use within early childhood educational institutions. We conducted a literature...... that can support the successful implementation of touch screen technology within early childhood educational institutions....... in regards to touch screen technology in early childhood, particularly from a process perspective, and suggest that further research is required to understand the interplay between individual actions and organisational structural influences. This will contribute to the development of an understanding...

Detailed measurements of deformation in the excavation disturbed zone

International Nuclear Information System (INIS)

Thompson, P.M.; Martino, J.B.; Spinney, M.H.

1993-01-01

An excavation damage extensometer (EDEX) is described. It was designed to enable detailed small-scale deformation measurements to be made in the excavation disturbed zone (EDZ) around a tunnel opening in stressed rock. Its use in the Mine-by Experiment in unfractured granitic rock at the Underground Research Laboratory (Manitoba) is described. The results obtained from an array of eight EDEX installations are presented. These demonstrate how the EDEX can be used to provide data on the EDZ which is supplementary to that obtained by larger scale borehole extensometers and a acoustic emission/micro-seismic monitoring system. (4 figures, 5 references) (UK)

Report on Excavations at Sedgeford, Norfolk 1996

Directory of Open Access Journals (Sweden)

Nick Cook

1997-11-01

Full Text Available Excavations were undertaken as part of the ongoing work of the Sedgeford Hall Archaeological Research Project, which was set up in 1995 with the aim of investigating the archaeological history of the parish of Sedgeford, west Norfolk.

Field Observation of Soil Displacements Resulting Due Unsupported Excavation and Its Effects on Proposed Adjacent Piles

Directory of Open Access Journals (Sweden)

Ala Nasir Al-Jorany

2016-06-01

Full Text Available Soil movement resulting due unsupported excavation nearby axially loaded piles imposes significant structural troubles on geotechnical engineers especially for piles that are not designed to account for loss of lateral confinement. In this study the field excavation works of 7.0 m deep open tunnel was continuously followed up by the authors. The work is related to the project of developing the Army canal in the east of Baghdad city in Iraq. A number of selected points around the field excavation are installed on the ground surface at different horizontal distance. The elevation and coordinates of points are recorded during 23 days with excavation progress period. The field excavation process was numerically simulated by using the finite element package PLAXIS 3D foundation. The obtained analysis results regarding the displacements of the selected points are compared with the field observation for verification purpose. Moreover, finite element analysis of axially loaded piles that are presumed to be existed at the locations of the observation points is carried out to study the effect of excavation on full scale piles behaviors. The field observation monitored an upward movement and positive lateral ground movement for shallow excavation depth. Later on and as the excavation process went deeper, a downward movement and negative lateral ground movement are noticed. The analyses results are in general well agreed with the monitored values of soil displacements at the selected points. It is found also that there are obvious effects of the nearby excavation on the presumed piles in terms of displacements and bending moments.

Safety analysis of autonomous excavator functionality

International Nuclear Information System (INIS)

Seward, D.; Pace, C.; Morrey, R.; Sommerville, I.

2000-01-01

This paper presents an account of carrying out a hazard analysis to define the safety requirements for an autonomous robotic excavator. The work is also relevant to the growing generic class of heavy automated mobile machinery. An overview of the excavator design is provided and the concept of a safety manager is introduced. The safety manager is an autonomous module responsible for all aspects of system operational safety, and is central to the control system's architecture. Each stage of the hazard analysis is described, i.e. system model creation, hazard definition and hazard analysis. Analysis at an early stage of the design process, and on a system that interfaces directly to an unstructured environment, exposes certain issues relevant to the application of current hazard analysis methods. The approach taken in the analysis is described. Finally, it is explained how the results of the hazard analysis have influenced system design, in particular, safety manager specifications. Conclusions are then drawn about the applicability of hazard analysis of requirements in general, and suggestions are made as to how the approach can be taken further

77 FR 27436 - Stevens Institute of Technology, et al.; Notice of Consolidated Decision on Applications for Duty...

Science.gov (United States)

2012-05-10

... Number: 12-014. Applicant: California Institute of Technology, Pasadena, CA 91125. Instrument: Nova Nano... DEPARTMENT OF COMMERCE International Trade Administration Stevens Institute of Technology, et al... Constitution Avenue NW, Washington, DC Docket Number: 12-008. Applicant: Stevens Institute of Technology...

Archeological Excavations at the Wanapum Cache Site

International Nuclear Information System (INIS)

T. E. Marceau

2000-01-01

This report was prepared to document the actions taken to locate and excavate an abandoned Wanapum cache located east of the 100-H Reactor area. Evidence (i.e., glass, ceramics, metal, and wood) obtained from shovel and backhoe excavations at the Wanapum cache site indicate that the storage caches were found. The highly fragmented condition of these materials argues that the contents of the caches were collected or destroyed prior to the caches being burned and buried by mechanical equipment. While the fiber nets would have been destroyed by fire, the specialized stone weights would have remained behind. The fact that the site might have been gleaned of desirable artifacts prior to its demolition is consistent with the account by Riddell (1948) for a contemporary village site. Unfortunately, fishing equipment, owned by and used on behalf of the village, that might have returned to productive use has been irretrievably lost

Dilmun revisited: excavations at Saar, Bahrain

Directory of Open Access Journals (Sweden)

Harriet Crawford

1997-11-01

Full Text Available About 2000 BC the island of Bahrain was at the centre of a prosperous trading community - the Early Dilmun civilization - that stretched from Mesopotamia to the Indus Valley. Excavations at the site of Saar have, since 1989, recovered much new information about the layout of the settlement and its local economy and social system.

Features of state industrial policy under imperfect technological and institutional environment

Directory of Open Access Journals (Sweden)

Denisov Igor Vladimirovich

2011-07-01

Full Text Available For all countries with imperfect technology and the institutional environment (low culture and organization of production, high levels of corruption, the small middle class, not necessarily the execution of laws, etc., even such strong measures to support the economy like a direct financing of firms and territories, protectionism, stimulation of demand, etc. does not give significant effect. For Russia, which objectively have to be attributed to such countries, extremely relevant management system development, capable of overcoming difficulties, starting with the knees and the resistance of the imperfect (bad technological and institutional environment. Several theoretical solutions recently obtained through the development of the theory of economic-technological development of civilization, can create the mechanism and conditions of such a system.

Characterization of enameled glass excavated from Laem Pho, southern Thailand

Science.gov (United States)

Dhanmanonda, W.; Won-in, K.; Tancharakorn, S.; Tantanuch, W.; Thongleurm, C.; Kamwanna, T.; Dararutana, P.

2012-07-01

Laem Pho in Surat Thani, southern province of Thailand is one of the most important historic site on the eastern shore of the Gulf of Thailand. In this work, the enameled glass fragments which looked-like Islamic glass mainly excavated from this site were analyzed using SEM-EDS, PIXE and μ-XRF, in order to understand the chemical composition by comparing the archaeological data and topology. The structure of the enameled decoration was also studied. The resulting data indicated that high-magnesia alkali-lime silicate glass was produced. The presence of transition metals such as copper, iron and manganese were affected on the glass colorations. Typological classifications, technological observations and comparative studies serve to clarify the development and cultural inter-relationships of various glass objects along the trade and exchange networks in ancient maritime.

Characterization of enameled glass excavated from Laem Pho, southern Thailand

International Nuclear Information System (INIS)

Dhanmanonda, W; Won-in, K; Tancharakorn, S; Tantanuch, W; Thongleurm, C; Kamwanna, T; Dararutana, P

2012-01-01

Laem Pho in Surat Thani, southern province of Thailand is one of the most important historic site on the eastern shore of the Gulf of Thailand. In this work, the enameled glass fragments which looked-like Islamic glass mainly excavated from this site were analyzed using SEM-EDS, PIXE and μ-XRF, in order to understand the chemical composition by comparing the archaeological data and topology. The structure of the enameled decoration was also studied. The resulting data indicated that high-magnesia alkali-lime silicate glass was produced. The presence of transition metals such as copper, iron and manganese were affected on the glass colorations. Typological classifications, technological observations and comparative studies serve to clarify the development and cultural inter-relationships of various glass objects along the trade and exchange networks in ancient maritime.

Characteristics of the Institute of Technology 'Prof. Jorge A. Sabato'

International Nuclear Information System (INIS)

Galvele, Jose R.

2001-01-01

A historical survey is made of the educational and training activities in metallurgy and material sciences carried out by the CNEA since 1962, that were the origin of the 'Prof. Jorge A. Sabato' Institute. Today the Institute, created by the CNEA in association with the National University of General San Martin, is preparing Engineers in Material Sciences and Masters and Ph. D. in Material Sciences and Technology (Mention in Physics and Material). The curricula of the studies are described in detail. The Information Center annexed to the Institute is also described

Fuzzy mathematics method for theoretical analysis of ground movements due to underground excavation

Energy Technology Data Exchange (ETDEWEB)

Li Wenxiu (Changsa Research Institute of Mining and Metallurgy, Changsa (China))

1991-07-01

The analysis of the rock mass movements due to excavation operations is one of the many important problems of rock mass mechanics. It is difficult to calculate the ground movements due to underground excavation accurately because of the complexity of the problem. In this paper, the application is described of the fuzzy probability measures to the analysis of ground movements. Based on the definition of the fuzzy probability measure, the theories for both the two-dimensional and three-dimensional problems are developed and are applied to the analysis of ground movements due to underground excavation. 31 refs., 5 figs.

Excavations at Pukearuhe (N99/49), North Taranaki, 1968

International Nuclear Information System (INIS)

Lawrence, J.; Prickett, N.

1984-01-01

The 1968 salvage excavations at Pukearuhe (N99/49), north Taranaki, are reported. Pukearuhe was for long a Ngati Tama fortification; in the period 1865-1885 it was occupied by european forces, firstly, imperial troops and Taranaki military settlers, later, armed constabulary. Ngati Tama and european occupation was based on the powerful strategic situation of Pukearuhe at the northern gateway into Taranaki. Excavations revealed evidence of the Maori and European occupation. Radiocarbon dates were obtained for Maori occupation. European material adds to the knowledge of sites relating to the period of military conflict in Taranaki which extended from 1860 to the early 1880s

Geotechnical characterization and construction methods for SSC tunnel excavation

International Nuclear Information System (INIS)

Nelson, P.P.; Lundin, T.K.

1990-06-01

The site for the Superconducting Super Collider (SSC) facility was selected in 1988 after a nationwide proposal competition. The selected site is located in Ellis County, Texas, surrounding the town of Waxahachie which is about 30 miles (48 km) south of the City of Dallas central business district. This paper will describe the geotechnical conditions anticipated for excavation at the SSC site. A general geologic and geomechanical description of the rock present will be followed by a summary of the site-specific conceptual design for the tunneled components of the SSC machine. The Supercollider project will include about 70 miles (113) km of tunnel excavation

Alternative cytoskeletal landscapes: cytoskeletal novelty and evolution in basal excavate protists

Science.gov (United States)

Dawson, Scott C.; Paredez, Alexander R.

2016-01-01

Microbial eukaryotes encompass the majority of eukaryotic evolutionary and cytoskeletal diversity. The cytoskeletal complexity observed in multicellular organisms appears to be an expansion of components present in genomes of diverse microbial eukaryotes such as the basal lineage of flagellates, the Excavata. Excavate protists have complex and diverse cytoskeletal architectures and life cycles – essentially alternative cytoskeletal “landscapes” – yet still possess conserved microtubule- and actin-associated proteins. Comparative genomic analyses have revealed that a subset of excavates, however, lack many canonical actin-binding proteins central to actin cytoskeleton function in other eukaryotes. Overall, excavates possess numerous uncharacterized and “hypothetical” genes, and may represent an undiscovered reservoir of novel cytoskeletal genes and cytoskeletal mechanisms. The continued development of molecular genetic tools in these complex microbial eukaryotes will undoubtedly contribute to our overall understanding of cytoskeletal diversity and evolution. PMID:23312067

Horonobe Underground Research Laboratory project. Plans of investigations during shaft and drift excavation (Construction of underground facilities: Phase II)

International Nuclear Information System (INIS)

2005-06-01

Horonobe Underground Research Laboratory Project is planned for over 20 years to establish the scientific and technical basis for the underground disposal of high-level radioactive wastes in Japan. The investigations are conducted by JNC in three phases, from the surface (Phase I), during the construction of the underground facilities (Phase II), and using the facilities (Phase III). This report concerns the investigation plans for Phase II. During excavation of shafts and drifts, detailed geological and borehole investigation will be conducted and the geological model constructed in Phase I is evaluated and revised by newly acquired data of geophysical and geological environment. Detailed in-situ experiments, as well as the effects of shaft excavation, are also done to study long-term changes, rock properties, groundwater flow and chemistry to ensure the reliability of repository technology and establish safety assessment methodology. (S. Ohno)

CASTLE3D - A Computer Aided System for Labelling Archaeological Excavations in 3D

Science.gov (United States)

Houshiar, H.; Borrmann, D.; Elseberg, J.; Nüchter, A.; Näth, F.; Winkler, S.

2015-08-01

Documentation of archaeological excavation sites with conventional methods and tools such as hand drawings, measuring tape and archaeological notes is time consuming. This process is prone to human errors and the quality of the documentation depends on the qualification of the archaeologist on site. Use of modern technology and methods in 3D surveying and 3D robotics facilitate and improve this process. Computer-aided systems and databases improve the documentation quality and increase the speed of data acquisition. 3D laser scanning is the state of the art in modelling archaeological excavation sites, historical sites and even entire cities or landscapes. Modern laser scanners are capable of data acquisition of up to 1 million points per second. This provides a very detailed 3D point cloud of the environment. 3D point clouds and 3D models of an excavation site provide a better representation of the environment for the archaeologist and for documentation. The point cloud can be used both for further studies on the excavation and for the presentation of results. This paper introduces a Computer aided system for labelling archaeological excavations in 3D (CASTLE3D). Consisting of a set of tools for recording and georeferencing the 3D data from an excavation site, CASTLE3D is a novel documentation approach in industrial archaeology. It provides a 2D and 3D visualisation of the data and an easy-to-use interface that enables the archaeologist to select regions of interest and to interact with the data in both representations. The 2D visualisation and a 3D orthogonal view of the data provide cuts of the environment that resemble the traditional hand drawings. The 3D perspective view gives a realistic view of the environment. CASTLE3D is designed as an easy-to-use on-site semantic mapping tool for archaeologists. Each project contains a predefined set of semantic information that can be used to label findings in the data. Multiple regions of interest can be joined under

118-B-1 excavation treatability test plan

International Nuclear Information System (INIS)

1994-07-01

The Hanford 118-B-1 Burial Ground Treatability Study has been required by milestone change request number-sign M-15-93-04, dated September 30, 1993. The change request requires that a treatability test be conducted at the 100-B Area to obtain additional engineering information for remedial design of burial grounds receiving waste from 100 Area removal actions. This treatability study has two purposes: (1) to support development of the Proposed Plan (PP) and Record of Decision (ROD), which will identify the approach to be used for burial ground remediation, and (2) to provide specific engineering information for receiving waste generated from the 100 Area removal actions. Data generated from this test also will provide critical performance and cost information necessary for remedy evaluation in the detailed analysis of alternatives during preparation of the focused feasibility study (FFS). This treatability testing supports the following 100 Area alternatives: (1) excavation and disposal, and (2) excavation, sorting, (treatment), and disposal

Waterford Institute of Technology, Tourism and Leisure Building

Directory of Open Access Journals (Sweden)

Chris Croly

2012-04-01

Full Text Available The Tourism and Leisure Building at Waterford Institute of Technology contains all of the passive design elements that would be expected in a landmark environmentally-conscious educational development. The design however also addresses energy conservation in complex, high-energy kitchen systems in an innovative way, bringing a new level of environmental performance to catering in Ireland.

Technological capabilities, institutions and firm productivity: a multilevel study

Czech Academy of Sciences Publication Activity Database

Goedhuys, M.; Srholec, Martin

2015-01-01

Roč. 27, č. 1 (2015), s. 122-139 ISSN 0957-8811 R&D Projects: GA ČR(CZ) GAP402/10/2310 Institutional support: RVO:67985998 Keywords : productivity * innovation * technological capability Subject RIV: AH - Economics Impact factor: 0.720, year: 2015

Case Studies and Monitoring of Deep Excavations

NARCIS (Netherlands)

Korff, M.

2017-01-01

Several case histories from Dutch underground deep excavation projects are presented in this paper, including the lessons learned and the learning processes involved. The focus of the paper is on how the learning takes places and how it is documented. It is necessary to learn in a systematic and

Geological mappability of bored versus drill and blast excavations for radioactive waste repositories

International Nuclear Information System (INIS)

Nilsen, B.; Ozdemir, L.

1992-01-01

The issue of accurate geological mappability has been subject of intense debate in the selection of bored versus drill and blast excavation for radioactive waste repositories. This paper is intended to provide an assessment of the problems usually encountered in mappability on the basis of field experience from a large number of completed tunnels, mainly as part of the Norwegian hydropower projects. The main conclusion is that mapping in a mechanically excavated underground opening, with very few exceptions, reflects the in-situ conditions more accurately than mapping in a drill and blast tunnel. This is due to the overbreak effects of drill and blast excavation, primarily

Technical summary of AECL's Mine-by Experiment phase I: Excavation response

International Nuclear Information System (INIS)

Read, R.S.; Martin, C.D.

1996-02-01

The first phase of the Mine-by Experiment was conducted at the 420 Level of the Underground Research Laboratory (URL) to investigate the response induced in the rock mass by excavating a 3.5-m-diameter circular tunnel using a non-explosive technique. The main objective of the experiment was to study the processes involved in progressive failure and the development of excavation-induced damage around underground openings. To this end, state-of-the-art geomechanical and geophysical instrumentation was used to monitor the excavation of the 46-m-long Mine-by Experiment test tunnel. The results from the experiment show that progressive failure in compressive regions around the tunnel initiates at stresses about 50% of the rock strength measured in uniaxial compression tests in the laboratory. The difference between the laboratory and in situ behaviour is attributed to complex stress changes that occur during excavation of the tunnel, especially in the vicinity of the advancing face. These effects are not simulated in standard laboratory tests. Numerical modelling and in situ characterization studies were conducted to establish the extent and characteristics of the damaged zone around the test tunnel. As part of this study, in situ stresses and material properties were established through back analysis of measured displacements and strains. Using these boundary conditions, it was shown that the damaged zone was limited to within 1 m of the original tunnel perimeter. The characteristics of the damaged zone, however, were found to be highly variable around the tunnel, and were dependent on the nature of the stress concentrations, geology, stress magnitudes and orientations and, to a lesser extent, the excavation method and sequence. (author) 136 refs., 14 tabs., 103 figs

Excavation damage and organic growth in a 1.2m diameter borehole

International Nuclear Information System (INIS)

Everitt, R.A.; Gann, P.; Brown, D.A.; Boychuk, D.M.

1994-01-01

A 1.24m diameter borehole was drilled 5m into the floor of a typical drill-and-blast tunnel in unfractured granite, at AECL's Underground Research Laboratory. Three generations of excavation damage, characteristic of what may be encountered in boreholes excavated for in-hole emplacement of used fuel wastes was observed. These include: (1) damage related to the initial excavation of the room, (2) damage caused by the drilling of the borehole itself, and (3) damage due to subsequent stress-induced spalling of the borehole walls. A biofilm containing a variety of microorganisms has developed where seepage issues from the concrete-granite interface. The biota were introduced from surface water used for mining and drilling. Their growth has been stimulated by residues from blasting and drilling, which have concentrated iron and silicon by passive sorption and energy metabolism. Ferrous iron has been oxidized and precipitated as ferrihydrite/hematite to give an orange/brown colouration on the biofilm interface black. These observations, significant to the understanding and monitoring of excavation damage, highlight the importance of thorough, in situ, multi-disciplinary characterization for vault design

Dam geology and basic treatment(2). Adit substitution technique and measures against landslide involved in excavation

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Kin' ichi [Kinki Geological Center, Co. Ltd., Kyoto, Japan (JP)

1988-12-25

This paper discusses the adit substitution technique which is a method for special treatment of dams and measures against landslide involved in excavation. The adit substitution technique consists of excavating an adit in the natural ground, excavating another adit which is in contact with the first adit and is at a level higher than the first adit, placing concrete from the upper adit to the lower adit to fill first adit completely with concrete, excavating a third adit, filling the second adit with concrete similarly, and proceeding with this process to construct a water barrier within the natural ground until the water barrier reaches the required height. The paper explains examples of this technique used on four dams. It also explains examples of measures against excavation-induced landslide adopted on three dams. 13 refs., 8 figs., 2 tabs.

Developing an Astronomy Program at the Crownpoint Institute of Technology

Science.gov (United States)

Gino, M. C.

2004-12-01

The Crownpoint Institute of Technology (CIT) is a tribal college located on the eastern edge of the Navajo Nation in northwestern New Mexico. Historically CIT is a technical college which grants AAS degrees and certificates in a number of vocational and technical fields. CIT is in the process of seeking higher learning articulation and accreditation, and has received "Candidacy Status" from the North Central Association of Colleges and Schools Commission on Institutions of Higher Education. To meet the demands placed upon the college as it steps into its role as an institution of higher learning, CIT is dedicated to broadening its curriculum with programs that encourage math, science and technology, and to increasing the number of courses that advance knowledge in both Navajo and Western society by enhancing both laboratory and educational technologies. The introduction of astronomy into the science curriculum advances CIT's goals in all of these areas, and presents a unique opportunity to incorporate traditional Navajo scientific knowledge into a technically advanced science program. In this poster we outline the development of the astronomy program, which has started with the inclusion of the first astronomy course into the science curriculum and the acquisition of two small telescope systems for K-14 student use and public outreach, and will continue through the construction of a campus observatory capable of supporting an undergraduate research program. It is our expectation that through the introduction of astronomy into the curriculum, CIT will advance its goals of increasing science and technology educational opportunities for its students and training the next generation of Navajo science and technology professionals, while maintaining an awareness of the needs of the Navajo Nation and a sensitivity to Navajo cultural values and protocols.

National Institute for Technology in Liberal Education: An Assessment. White Paper

Science.gov (United States)

Brodeur, Jason; Daniels, Morgan; Johnson, Annie; Nicholls, Natsuko; Pickle, Sarah; Waraksa, Elizabeth A.

2016-01-01

In 2001, the National Institute for Technology in Liberal Education (NITLE) was created to "stimulate collaboration between selected liberal arts colleges and to act as a catalyst for the effective integration of emerging and newer digital technologies into teaching, learning, scholarship, and information management." In July 2015, NITLE…

Zedex - an in-situ study of the importance of the excavation disturbed zone to repository performance

International Nuclear Information System (INIS)

Olsson, O.; Slimane K.B.; Davies, N.

1995-01-01

The excavation of shafts and tunnels in a waste repository will cause a disturbance to the surrounding rock mass with possible alterations to rock mass stability and hydraulic properties. The properties and extent of the disturbed zone must be considered in the design of a repository and in the assessment of its long-term safety. In addition, the data collected in drifts, which will be used for detailed characterization of the repository, will be affected by excavation effects. ANDRA, UK Nirex, and SKB have jointly set up the ZEDEX Project at the Aespoe Hard Rock Laboratory, Sweden, in order to improve understanding of the properties and extent the Excavation Disturbed Zone (EDZ). The main objective is to study the mechanical behavior of the EDZ with respect to its origin, character, magnitude of property change, extent, and its dependence of excavation method. The project will also provide a test of equipment and methodology for quantifying the EDZ. The ZEDEX Project includes tests of open-quote normal close-quote excavation by drill and blast, a smooth blasting procedure based on low shock explosives, and excavation by tunnel boring. The ZEDEX Project is still in progress and results have not been fully analyzed. The preliminary analysis of the results indicates that the measurable changes in properties induced by tunnel excavation are comparatively small

Hydraulic tests for the Excavation Disturbed Zone in NATM drift of North Extension

International Nuclear Information System (INIS)

Matsuoka, Eiken

1997-03-01

Investigation for characterization of rock properties of the Excavation Disturbed Zone (EDZ) were carried out in NATM drift of North Extension in the Tono Mine. As a part of this investigation, hydraulic tests were performed by means of the hydraulic measuring instrument, which had been developed by PNC Tono Geoscience Center. The purpose of this tests is to characterize the change in hydraulic properties of the EDZ caused by drift excavation using machine (boom header). The hydraulic tests were performed in the burials MH-1,2,3, in which hydraulic tests had been performed before the drift excavation in 1994. The test results indicate that the measured values of pore water pressure have decreased after excavation of the drift. The values ranged from -0.037 kgf/cm 2 to 0.039 kgf/cm 2 . The measured hydraulic conductivities ranged from 2.2*10 -11 cm/s to 9.1*10 -11 cm/s for mud stone and from 2.8*10 -9 cm/s to 2.4*10 -7 cm/s for conglomerate. The measured hydraulic conductivities for mud stone are below the lower limit of the instrument, and the change in the hydraulic conductivities for conglomerate is little. The hydraulic conductivities for conglomerate and mad stone (reference values) are interpreted. The change in hydraulic conductivities measured before and after excavation of the drift is insignificant. (author)

Bonding experiences with Ecuadorian society from the attention to diversity in the Bolivarian Technological Institute of Technology

Directory of Open Access Journals (Sweden)

Wendy Roxana Cortés-Guerrero

2016-09-01

Full Text Available This work aims to systematize the results obtained with the Institutional implemented in the Bolivarian Technological Institute of Technology in the city of Guayaquil in the Republic of Ecuador Program Linking with Society “COMMUNITY HEALTH”. From his humanistic approach and attention to diversity, is extended permanently services to society, to articulate academia-research community, comes in this way to the most vulnerable populations of the city and surrounding counties. The indicators evaluated, allow to high light a successful evolution of the program, to encourage the improvement and expansion of services provided by students and professional teachers in different branches.

Annual Report of Institute of Nuclear Chemistry and Technology 1999

International Nuclear Information System (INIS)

2000-06-01

The INCT 1999 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology, Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics and nucleonic control systems and accelerators

Annual Report of Institute of Nuclear Chemistry and Technology 2002

International Nuclear Information System (INIS)

2003-06-01

The INCT 2002 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology, Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators

Annual Report of Institute of Nuclear Chemistry and Technology 2002

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-06-01

The INCT 2002 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology, Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators.

Annual Report of Institute of Nuclear Chemistry and Technology 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

The INCT 1999 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology, Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics and nucleonic control systems and accelerators.

Mine-by experiment committee report phase 1: excavation response summary and implications

International Nuclear Information System (INIS)

Martin, C.D.; Kaiser, P.K.

1996-05-01

The first phase of the Mine-by Experiment, i.e., excavation of a 3.5-m-diameter tunnel, was carried out at the 420 Level of the Underground Research Laboratory to investigate rock mass damage and progressive failure around a circular opening in brittle unfractitred Lac du Bonnet granite. The tunnel was excavated without explosives, and state-of-the-art instrumentation comprising both geomechanical and geophysical instruments was used to monitor the failure process. The experiment showed that rock mass damage begins once the deviatoric stress (0'1 - 0'3) near the advancing face of the tunnel exceeds a critical level. Crack propagation can lead to progressive failure around the tunnel; however, it is limited to a region, referred to as the excavation damaged zone, of less than one tunnel radius. Within the damaged zone, stabbing (a typical form of brittle failure) began at stress levels equivalent to about 50% of the short-term laboratory unconfined compressive strength. This reduction in strength between laboratory and in situ conditions occurs because the in situ loading path is far more complex than the monotonic loading path used to test laboratory samples. There is no evidence to suggest that the stabbing failure process would extend beyond the depth of damage defined by the deviatoric stress criterion. The stabbing process stops when the tunnel face has advanced sufficiently (approximately 2 tunnel diameters) such that the rock mass is no longer subjected to excavation-induced stress changes. The strength of the rock mass in the damaged zone must be back-calculated from in situ tests, because the loading path cannot be duplicated readily in the laboratory. Thus, the back-calculated damaged strength must be used to evaluate the stability of the excavation. Sealing systems to reduce the permeability in the axial direction of a tunnel must be keyed into the rock mass beyond the radial extent of the damaged zone. The shape of the seals must be designed so as to

A low-cost approach for the documentation and monitoring of an archaeological excavation site

Science.gov (United States)

Hoffmeister, Dirk; Orrin, Joel; Richter, Jürgen

2016-04-01

The documentation of archaeological excavations and in particular a constant monitoring is often time-consuming and depending on humańs capabilities. Thus, remote sensing methods, which allow an objective reproduction of the current state of an excavation and additional information are of interest. Therefore, a low-cost approach was tested on an open-air excavation site for two days in September 2015. The Magdalenian excavation site of Bad Kösen-Lengefeld, Germany is one important site in a system of about 100 sites in the area of the small rivers Saale and Unstrut. The whole site and the surrounding area (200 by 200 m) was first observed by a GoPro Hero 3+ mounted on a DJI-Phantom 2 UAV. Ground control points were set-up in a regular grid covering the whole area. The achieved accuracy is 20 mm with a ground resolution of 45 mm. As a test, the GoPro Hero 3+ camera was additionally mounted on a small, extendable pole. With this second low-cost, easy to apply monitoring approach, pictures were automatically taken every second in a stop-and-go mode. In order to capture the excavation pit (7 by 4 m), two different angles were used for holding the pole, which focused on the middle and on the border of the pit. This procedure was repeated on the following day in order to document the excavation process. For the registration of the images, the already existing and measured excavation nails were used, which are equally distributed over the whole site in a 1 m grid. Thus, a high accurate registration of the images was possible (>10 mm). In order to approve the accuracy of the already derived data, the whole site was also observed by a Faro Focus 3D LS 120 laser scanner. The measurements of this device were registered by spherical targets, which were measured in the same reference system. The accuracy of the registration and the ground resolution for the image based approach for both days was about 4 mm. From these two measurements the process of the excavation was easily

29 CFR 1926.651 - Specific excavation requirements.

Science.gov (United States)

2010-07-01

...) Exposure to vehicular traffic. Employees exposed to public vehicular traffic shall be provided with, and... containing a concentration of a flammable gas in excess of 20 percent of the lower flammable limit of the gas... ensure proper operation. (3) If excavation work interrupts the natural drainage of surface water (such as...

Information actions in science and technology: institutionalities, agencies and subjects

Directory of Open Access Journals (Sweden)

Rodrigo Rabello

Full Text Available Considering the influence of new agency forms - intervention and interaction among subjects - in the context of information intermediation, we aim to approach information actions in Science and Technology (S&T taking into consideration the institutionalities involved. For such, we assume there is an influence of a theoretical model emerging in Information Science (IS regarding current inventive and interactive form propitiated by the Web. The text is structured in two central topics bringing: i theoretical and epistemic constructions of the "information action" concept; and ii a certain interpretation oriented by the "informational action in S&T" construct, taking as its object the actions performed by IBICT (Brazilian Institute for Information in Science and Technology, directed towards excellence in information. Finally, we discuss how limitations of the "systemic model" propitiate the construction of new study objects in the model emerging in IS from theoretical innovations and counterpoints thoughts facing the diverse forms of information action, considering, for instance, the action of subjects on what concerns the validation of information in the current scenery of institutional intermediation.

Support system, excavation arrangement, and process of supporting an object

Science.gov (United States)

Arnold, Bill W.

2017-08-01

A support system, an excavation arrangement, and a process of supporting an object are disclosed. The support system includes a weight-bearing device and a camming mechanism positioned below the weight-bearing device. A downward force on the weight-bearing device at least partially secures the camming mechanism to opposing surfaces. The excavation arrangement includes a borehole, a support system positioned within and secured to the borehole, and an object positioned on and supported by the support system. The process includes positioning and securing the support system and positioning the object on the weight-bearing device.

Excavation induced damage evolution during a mine-by experiment in Opalinus Clay

International Nuclear Information System (INIS)

Vietor, T.; Armand, G.; Nyonoya, S.; Schuster, K.; Wieczorek, K.

2010-01-01

Document available in extended abstract form only. In Switzerland Opalinus Clay, a potential host rock formation for a nuclear waste repository, is intensively studied in the Mont Terri Underground Rock Laboratory (URL) in North-Western Switzerland. During the 2008 extension of the URL, the construction works were repeatedly interrupted to implement monitoring systems for a mine-by experiment. The future position of a 24 m long tunnel was instrumented with 36 different monitoring systems comprising approximately 200 sensors. Key features of this tunnel were chosen similar to the current Swiss concept for emplacement tunnels for High Level Radioactive Waste: circular section, full-face excavation following the geological bedding, support by a thin layer of shotcrete and 6 anchors every 1.3 m. For a mine-by experiment 26 boreholes were equipped with 7 multipoint extensometers, two multi segment inclinometer chains and 26 pore pressure chambers. The data acquisition system recorded 12 data sets per hour. For seismic transmission and acoustic emission monitoring, 8 piezo-electric emitters and 15 piezo-electric receivers were installed in 5 boreholes. The excavation of the instrumented tunnel took place in October/November 2008. The activities on the site were monitored with a web cam to separate spontaneous and excavation induced rock mass reactions. Daily mappings of the tunnel face and the sidewalls revealed the fracture pattern that was generated ahead of the advancing excavation. Three sets of excavation activated discontinuities could be clearly identified. These three sets develop within the framework of the pre-existing tectonic micro-faults that generally have a half-meter spacing. Where their density is high the intensity of excavation induced new slip planes apparently drops. Despite the presence of micro-faults the deformation monitoring around the advancing tunnel face showed a remarkably homogenous response to the excavation. Inclinometer chain segments

Biofuel or excavation? - Life cycle assessment (LCA) of soil remediation options

Energy Technology Data Exchange (ETDEWEB)

Suer, Pascal; Andersson-Skoeld, Yvonne [Swedish Geotechnical Institute, 58193 Linkoeping (Sweden)

2011-02-15

The environmental consequences of soil remediation through biofuel or through dig-and-dump were compared using life cycle assessment (LCA). Willow (Salix viminalis) was actually grown in-situ on a discontinued oil depot, as a phytoremediation treatment. These data were used for the biofuel remediation, while excavation-and-refill data were estimated from experience. The biofuel remediation had great environmental advantages compared to the ex situ excavation remediation. With the ReCiPe impact assessment method, which included biodiversity, the net environmental effect was even positive, in spite of the fact that the wood harvest was not utilised for biofuel production, but left on the contaminated site. Impact from the Salix viminalis cultivation was mainly through land use for the short rotation coppice, and through journeys of control personnel. The latter may be reduced when familiarity with biofuel as a soil treatment method increases. The excavation-and-refill remediation was dominated by the landfill and the transport of contaminated soil and backfill. (author)

Differences in technology innovation R&D performance creation behavior between for-profit institutions and not-for-profit institutions.

Science.gov (United States)

Park, Sungmin

2016-01-01

The present study compares the performance creation behavior between for-profit institutions and not-for-profit institutions within a national technology innovation research and development (R&D) program. Based on the stepwise performance creation chain structure of typical R&D logic models, a series of successive binary logistic regression models is newly proposed. Using the models, a sample of n = 2076 completed government-sponsored R&D projects was analyzed. For each institution type, its distinctive behavior is diagnosed, and relevant implications are suggested for improving the R&D performance.

Annual Report of Institute of Nuclear Chemistry and Technology 2001

International Nuclear Information System (INIS)

2002-06-01

The INCT 2001 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology in Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators and nuclear analytical methods

Annual Report 2004 of Institute of Nuclear Chemistry and Technology

International Nuclear Information System (INIS)

Michalik, J.; Smulek, W.; Godlewska-Para, E.

2005-06-01

The INCT 2004 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators, radiobiology and nuclear analytical methods

Annual Report 2004 of Institute of Nuclear Chemistry and Technology

Energy Technology Data Exchange (ETDEWEB)

Michalik, J; Smulek, W; Godlewska-Para, E [eds.

2005-06-01

The INCT 2004 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators, radiobiology and nuclear analytical methods.

Annual Report of Institute of Nuclear Chemistry and Technology 2001

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-06-01

The INCT 2001 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology in Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics, nucleonic control systems and accelerators and nuclear analytical methods.

Electronic Commerce: Canadian Community Colleges and Institutes of Technology.

Science.gov (United States)

Association of Canadian Community Colleges.

This paper reports on the Canadian college system's collaboration with industry and community services in the development and delivery of non-credit e-commerce courses offered through continuing education departments at community colleges and institutes of technology. The paper argues that, in today's changing economy, the accelerated need for…

In Appreciation of Claude Warren and Susan Rose's "William Pengelly's Techniques of Archaeological Excavation"

Directory of Open Access Journals (Sweden)

David L. Browman

1997-11-01

Full Text Available The short (40 pages pamphlet by Warren and Rose (1994 provides the answer to a complex question regarding credit for an important archaeological methodology, stratigraphic excavation. Let me set the stage for this appreciation. Continuing research on the beginnings of stratigraphic excavations in North America (Browman and Givens 1996, I sought the origins of the idea of actually excavating by strata, rather than post-facto interpretation, seen in North American as early as 1895 in the work of Henry Chapman Mercer, but not really introduced into the repertoire of American techniques until the work of Gamio, Kidder and Nelson between 1911 and 1914. The roots of the latter three seemed to lie with individuals such as Reisner, Boas, Uhle, who in turn seemed to rely on Hugo Obennaier, Gabriel de Mortillet, Marcellin Boule, and perhaps Pitt-Rivers, while Mercer's work could be traced to Boule and Albert Gaudry. Doggedly following back the roots, I found that Chapman (1989 could make a reasonable case that Pitt-Rivers had actually learned of the idea of strati­graphic excavation from Evans, Prestwich, and Lubbock, from the British scientists working with the Upper and Middle Paleolithic excavations during 1858-1868.

Designing institutions for climate change: Why rational design involves technology

Energy Technology Data Exchange (ETDEWEB)

Coninck, H. de [Energy Research Centre of the Netherlands, Petten (Netherlands)

2008-09-30

This paper aims to explore how to augment the institutional solutions offered by current political theory for addressing the unprecedented problem of climate change. Although steering directly at emission reductions in an international treaty has benefits in terms of cost-effectiveness, the paper arrives at the conclusion that considerations around technological development should be drawn into the treaty equation in order to generate sufficient reciprocity to have a politically feasible international regime. It then argues that the benefits of technology agreements for climate change mitigation may be larger than commonly assumed, as they - if properly designed - could lead to real emission reductions and provide more flexibility to reach agreement in post-2012 negotiations than proposals modelled exclusively on the Kyoto Protocol or other types of absolute emission targets. Based on rational design of international institutions for environmental governance, and attempting to take into account considerations of technological dynamics and the 'sociotechnical system', contours of a possible environmentally effective and politically feasible international climate change agreements are sketched.

Public Action and Innovationsupport Institutions in New Technological Agglomerations

DEFF Research Database (Denmark)

Borras, Susana; Bacaria, Jordi; Fernandez-Ribas, Andrea

2002-01-01

In all industrial and technological agglomerations several types of public and semi-public actors coexist. The same happens with the levels of government. Consequently, the daily reality of agglomerations is characterized by a wide diversity of innovation-support institutions more or less actively...... on the major efforts of different public actors in the territory since the 1980s, mainly through the establishment and enhancement of innovation-support institutions, and analyses succinctly their effects through selected successful and failed cases. Two normative statements are suggested from the analysis....... The first is that policy strategies should not try to be hegemonic. Instead, they should be elaborated seeking complementarity and coexistence. A second normative conclusion is the necessity of fostering the learning processes within and across institutions, by mobilizing collectively the assets of the area...

Physico-chemical properties of excavated plastic from landfill mining and current recycling routes.

Science.gov (United States)

Canopoli, L; Fidalgo, B; Coulon, F; Wagland, S T

2018-06-01

In Europe over 5.25 billion tonnes of waste has been landfilled between 1995 and 2015. Among this large amount of waste, plastic represents typically 5-25 wt% which is significant and has the potential to be recycled and reintroduced into the circular economy. To date there is still however little information available of the opportunities and challenges in recovering plastics from landfill sites. In this review, the impacts of landfill chemistry on the degradation and/or contamination of excavated plastic waste are analysed. The feasibility of using excavated plastic waste as feedstock for upcycling to valuable chemicals or liquid fuels through thermochemical conversion is also critically discussed. The limited degradation that is experienced by many plastics in landfills (>20 years) which guarantee that large amount is still available is largely due to thermooxidative degradation and the anaerobic conditions. However, excavated plastic waste cannot be conventionally recycled due to high level of ash, impurities and heavy metals. Recent studies demonstrated that pyrolysis offers a cost effective alternative option to conventional recycling. The produced pyrolysis oil is expected to have similar characteristics to petroleum diesel oil. The production of valuable product from excavated plastic waste will also increase the feasibility of enhanced landfill mining projects. However, further studies are needed to investigate the uncertainties about the contamination level and degradation of excavated plastic waste and address their viability for being processed through pyrolysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

An agent-based model of centralized institutions, social network technology, and revolution.

Science.gov (United States)

Makowsky, Michael D; Rubin, Jared

2013-01-01

This paper sheds light on the general mechanisms underlying large-scale social and institutional change. We employ an agent-based model to test the impact of authority centralization and social network technology on preference falsification and institutional change. We find that preference falsification is increasing with centralization and decreasing with social network range. This leads to greater cascades of preference revelation and thus more institutional change in highly centralized societies and this effect is exacerbated at greater social network ranges. An empirical analysis confirms the connections that we find between institutional centralization, social radius, preference falsification, and institutional change.

Impact-Actuated Digging Tool for Lunar Excavation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Honeybee Robotics proposes to develop a vacuum compatible, impact-actuated digging tool for the excavation of frozen and compacted regolith on the lunar surface and...

A new bee species that excavates sandstone nests

Science.gov (United States)

Many wonder why animals act in seemingly injurious ways. Understanding the behavior of pollinators such as bees is especially important because of the necessary ecosystem service they provide. The new species Anthophora pueblo, discovered excavating sandstone nests, provides a model system for addre...

Air Quality and Microclimatic Parameters During Excavation of Mala Kapela Tunnel

Directory of Open Access Journals (Sweden)

Mario Klanfar

2015-06-01

Full Text Available During excavation of the Mala Kapela tunnel, measurements of harmful gases concentration, ventilation parameters and microclimatic parameters were performed. Measurements were done in 17 occasions during period of 16 months, along the advance of the tunnel excavation. Consequently, large amount of data was obtained, in different tunnel chainages, ventilation ducts length, and in different work operations during the excavation. Main sources of harmful gases during tunnel excavation are explosives and diesel equipment. The concentration of the same mainly depends on explosive charge and overall diesel equipment power, present at the excavation face of the tunnel. Continuous measurements of the concentration of carbon monoxide (CO and dioxide (CO2, and nitrogen oxide (NO and dioxide (NO2 was performed during drilling, blasting, and loading and haulage operations. Measurements were done in 45 cases in total. Recorded data was analysed, where peak concentrations were joined to corresponding operation and the tunnel chainage. Regulations on threshold limit values were used to determine if concentrations rise above the permissible ones. In case they do, the time required for dilution of gases below permissible concentration was noted. Typically, concentrations of all measured gases rise rapidly after blasting. Afterwards, ventilation system acts to dilute them and maintain them relatively constant until the end of loading and haulage. According to measurements in this research, highest concentrations and longest time of dilution were found after blasting. At the same time, concentration of all measured gases exceeds permissible values. Carbon monoxide is found to exceed permissible values during all work operations. It shows most frequent transgression above the limit (in 33 to 100% of cases and highest time of dilution (up to 40 min. Air supply to the excavation face was measured in 25 cases. It was correlated to the length of ventilation ducts, as

Production technology readiness assessment of surfactant in the research center for Chemistry-Indonesian Institute of Sciences

Science.gov (United States)

Setiawan, Arief Ameir Rahman; Sulaswatty, Anny

2017-11-01

The common problem faced by the institution working on research, innovation and technology development is lack of quantitative measures to determine the technology readiness of research. No common communication language between R & D Institutions and industry about the level of preparedness of a research resulting a barrier to technology diffusion interaction. This lack of connection between R & D institutes with industry may lead to "sluggishness" occurs in innovating. For such circumstance, assessing technology readiness of research is very important. One of wide spread methods for the assessment is Technology Readiness Level (TRL, also known as Technometer), which is introduced by NASA (National Aeronautics and Space Administration). TRL is a general guide that provides an overview of maturity level of a technology. This study aims to identify and demonstrate the implementation of TRL to assess a number of surfactant researches in the Research Center for Chemistry, Indonesian Institute of Sciences. According to the assessment, it has been obtained the surfactant recommended for further development towards commercialization of R & D results, i.e. Glycerol Mono Stearate (GMS), which has reached the level of TRL 7.

78 FR 12065 - National Institute for Occupational Safety and Health Personal Protective Technology for...

Science.gov (United States)

2013-02-21

... Institute for Occupational Safety and Health Personal Protective Technology for Pesticide Handlers: Stakeholder Meeting AGENCY: The National Institute for Occupational Safety and Health (NIOSH) of the Centers...: Notice of public meeting. SUMMARY: The National Institute for Occupational Safety and Health (NIOSH) of...

EM-54 Technology Development In Situ Remediation Integrated Program

International Nuclear Information System (INIS)

1993-08-01

The Department of Energy (DOE) established the Office of Technology Development (EM-50) as an element of Environmental Restoration and Waste Management (EM) in November 1989. EM manages remediation of all DOE sites as well as wastes from current operations. The goal of the EM program is to minimize risks to human health, safety and the environment, and to bring all DOE sites into compliance with Federal, state, and local regulations by 2019. EM-50 is charged with developing new technologies that are safer, more effective and less expensive than current methods. The In Situ Remediation Integrated Program (the subject of this report) is part of EM-541, the Environmental Restoration Research and Development Division of EM-54. The In Situ Remediation Integrated Program (ISR IP) was instituted out of recognition that in situ remediation could fulfill three important criteria: Significant cost reduction of cleanup by eliminating or minimizing excavation, transportation, and disposal of wastes; reduced health impacts on workers and the public by minimizing exposure to wastes during excavation and processing; and remediation of inaccessible sites, including: deep subsurfaces; in, under, and around buildings. Buried waste, contaminated soils and groundwater, and containerized wastes are all candidates for in situ remediation. Contaminants include radioactive wastes, volatile and non-volatile organics, heavy metals, nitrates, and explosive materials. The ISR IP tends to facilitate development of in situ remediation technologies for hazardous, radioactive, and mixed wastes in soils, groundwater, and storage tanks. Near-term focus is on containment of the wastes, with treatment receiving greater effort in future years

A method of modeling time-dependent rock damage surrounding underground excavations in multiphase groundwater flow

International Nuclear Information System (INIS)

Christian-Frear, T.; Freeze, G.

1997-01-01

Underground excavations produce damaged zones surrounding the excavations which have disturbed hydrologic and geomechanical properties. Prediction of fluid flow in these zones must consider both the mechanical and fluid flow processes. Presented here is a methodology which utilizes a mechanical model to predict damage and disturbed rock zone (DRZ) development around the excavation and then uses the predictions to develop time-dependent DRZ porosity relationships. These relationships are then used to adjust the porosity of the DRZ in the fluid flow model based upon the time and distance from the edge of the excavation. The application of this methodology is presented using a site-specific example from the Waste Isolation Pilot Plant, a US Department of Energy facility in bedded salts being evaluated for demonstration of the safe underground disposal of transuranic waste from US defense-related activities

Detecting defects in diaphragm walls prior to excavation

NARCIS (Netherlands)

Spruit, R.; Hopman, V.; Van Tol, A.F.; Broere, W.

2011-01-01

Recent incidents with leaking diaphragm walls during construction of subway lines in Amsterdam and Rotterdam (Netherlands) have led to reconsideration of the diaphragm wall as a retaining wall construction for deep excavations. In our opinion the joints between the panels are the weak spot. During

Annual Report of Institute of Nuclear Chemistry and Technology 1998

International Nuclear Information System (INIS)

1999-04-01

Actual edition of Annual Report is a full review of scientific activities of the Institute of Nuclear Chemistry and Technology (INCT), Warsaw, in 1998. The abstracts are presented in the following group of subjects: radiation chemistry and physics, radiation technologies (26); radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general (25); radiobiology (11); nuclear technologies and methods - process engineering (5); material engineering, structural studies and diagnostics (9); nucleonic control systems (7). The edition also included the list of INCT scientific publications and patents as well as information on conferences organized or co-organized by the INCT in 1998

Annual Report 2003 of the Institute of Nuclear Chemistry and Technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The INCT 2003 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies, nucleonic control systems and accelerators.

Annual Report 2003 of the Institute of Nuclear Chemistry and Technology

International Nuclear Information System (INIS)

2004-01-01

The INCT 2003 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies, nucleonic control systems and accelerators

The material of the social: the mutual shaping of institutions by irrigation technology and society in Seguia Khrichfa, Morocco

Directory of Open Access Journals (Sweden)

Saskia van der Kooij

2015-03-01

Full Text Available In this paper we draw attention to the important role technology plays in co-mediating institutions, opening up some courses of action and closing off others. Irrigation studies generally recognize the importance of institutions in making technologies work, but tend to take the precise functioning of institutions for granted. Studies that analyse institutions often do not pay enough attention to the mediating role of technology in allocating benefits, risks and burdens. We show in this paper that (irrigation institutions are moulded by and come about through the interactions between the technical and the social in dynamic and often contested processes of adaptation to changing environments. We argue that a critical understanding of what institutions do requires more explicit and detailed attention to technologies. We base this argument on a detailed historical analysis of the functioning of Seguia Khrichfa, a farmer managed irrigation scheme in Morocco. Through time, irrigation institutions in the Seguia Khrichfa have undergone transformations to match the changing demands of a heterogeneous and growing group of irrigators, an increased command area and changing cropping patterns, and the introduction of new technologies such as drip irrigation. These institutional transformations consisted of recursive cycles of modifications in technological infrastructure and the rules of allocation and distribution. Technical adaptations prompt alterations in the water rotation schedule and vice versa. We anchor our case in descriptions of a specific technology that played a crucial role in co-steering institutional change: the introduction of open/closed gates. Our analysis of the co-evolution of society and technology in shaping institutions in the Seguia Khrichfa shows how technologies become enrolled in (sometimes implicit processes of re-negotiating relations of authority and responsibility while obscuring institutional politics.

Ghana Space Science and Technology Institute (GSSTI) - Annual Report 2015

International Nuclear Information System (INIS)

2015-01-01

The Ghana Space Science and Technology Institute (GSSTI) of the Ghana Atomic Energy Commission was established to exploit space science and technology for socio-economic development of Ghana. The report gives the structure of GSSTI and the detailed activities of the year. Various activities include: training and seminars, projects and workshops. Publications and their abstracts are also listed. The report also highlights some of the challenges, provides some recommendations and points to some expectation for the following year.

The adoption of mechanized excavation techniques for the Superconducting Super Collider

International Nuclear Information System (INIS)

Laughton, C.; Nelson, P.; Lundin, T.

1991-01-01

The Superconducting Super Collider (SSC) is the latest and largest in a line of high-energy physics accelerator projects. The five increasingly energetic accelerators which make up the physics laboratory complex are to be housed almost entirely in subsurface structures, which will include over 100 km of small-diameter tunnel. Among other reasons, the Texas SSC site was chosen from a set of state proposals because of the suitability of the host rock materials for the performance of rapid and efficient excavation work. This site bedrock units are relatively soft and homogeneous and should allow for a maximum use of mechanical excavation plant for the various underground openings. This paper will review the site conditions and describe the developed understanding of geologic material behavior. With completion of planned large-scale in-situ studies of the ground behavior to provide acquisition of early site-specific excavation data, final design and construction detail of critical structures can be undertaken with the necessary degree of confidence to satisfy the stringent performance requirements. 5 refs., 4 figs., 6 tabs

A study on excavation of rock mass by lasers. Researching the possibility of utilizing low-power lasers

Energy Technology Data Exchange (ETDEWEB)

Ito, Fumio [Taisei Corporation, Technology Research Center, Yokohama, Kanagawa (Japan)

2000-03-01

The object of this research is to develop the techniques of rock-mass excavation by laser irradiation. This rock-mass excavation technique by lasers has a characteristic of extremely little effect to the surroundings of an excavation site no matter how the target rock mass is with regard to geological aspects and given physical property. Moreover, it could be utilized in excavation of waste dump facilities, which need to be re-buried, and applied to excavation of long piles and tunnels, which are drilled through different kinds of strata, and to improvement of rock mass and ground. Lasers have a characteristic of concentrating the energy into a limited point and not only discontinue or cut a large area with a small output like sharp scissors but also block up the cracks deep inside the rock mass by fusing vitrification for its improvement. It leads to restrain the loss of energy, minimization of the effected environment, effective utilization of resources and energy, environmental restoration, and improvement of the working environment. In the field of nuclear fuel, which includes excavating dump pits, dismantling a furnace, and taking appropriate steps of mine remains, excavating, cutting, and fusing could be required to do within a limited space of rock mass or concrete. Up to the present, those things have been done mainly by large machines, but it is too scarce in possibility for them to improve their large size, heavy weight, difficulty in unmanned operation, limited shapes of cutting, and stabilization of waste. In this research the concrete system images have been examined, doing the fundamental researches about higher-power lasers, smaller sizing, transmitting by fibers to find our the breakthrough to realization of laser excavation, This year, as the summary of examining the laser excavation techniques, utilizing a low-power laser, which is thought to be highly effective in rock-mass improvement, will be examined, considering application of the technique

3D Numerical Modeling of Pile Group Responses to Excavation-Induced Stress Release in Silty Clay

Directory of Open Access Journals (Sweden)

M. A. Soomro

2018-02-01

Full Text Available Development of underground transportation systems consists of tunnels, basement construction excavations and cut and cover tunnels which may encounter existing pile groups during their construction. Since many previous studies mainly focus on the effects of excavations on single piles, settlement and load transfer mechanism of a pile group subjected to excavation-induced stress release are not well investigated and understood. To address these two issues, three-dimensional coupled-consolidation numerical analysis is conducted by using a hypoplastic model which takes small-strain stiffness into account. A non-linear pile group settlement was induced. This may be attributed to reduction of shaft resistance due to excavation induced stress release, the pile had to settle substantially to further mobilise end-bearing. Compared to the Sp of the pile group, induced settlement of the single pile is larger with similar settlement characteristics. Due to the additional settlement of the pile group, factor of safety for the pile group can be regarded as decreasing from 3.0 to 1.4, based on a displacement-based failure load criterion. Owing to non-uniform stress release, pile group tilted towards the excavation with value of 0.14%. Due to excavation-induced stress release and dragload, head load of rear piles was reduced and transferred to rear piles. This load transfer can increase the axial force in front piles by 94%.

Measurement plan and observational construction program on drift excavation at the Horonobe Underground Research Laboratory project

International Nuclear Information System (INIS)

Yamasaki, Masanao; Yamaguchi, Takehiro; Funaki, Hironori; Fujikawa, Daisuke; Tsusaka, Kimikazu

2008-09-01

The Horonobe URL Project is being pursued by the Japan Atomic Energy Agency (JAEA) to enhance the reliability of relevant disposal technologies through investigations of the deep geological environment within the host sedimentary formations at Horonobe, northern Hokkaido. The project consists of two major research areas, 'Geoscientific Research' and 'R and D' on Geological Disposal', and proceeds in three overlapping phases, 'Phase I: Surface-based investigation', 'Phase II: Construction' and 'Phase III: Operation', over a period of 20 years. On the Horonobe URL Project, 'Phase 1' was finished in 2005FY and construction of the underground facility was started since then. Now, 'Phase 2' (investigations during construction of the underground facilities) is on-going. On the 'Development of engineering techniques for use in the deep underground environment' in Phase 1, based on the various types of data acquired on investigations from the surface, the design of underground facility in advance was planned. At the inception of the Phase II investigations, an investigation report titled 'Measurement Plan and Observational Construction Program on Shaft Excavation at the Horonobe URL Project' (hereinafter referred to as 'Observational Construction Program') was published. The Observational Construction Program summarizes followings from the Phase I investigations: measurements for safety/reasonable construction, measurements for R and D on enhancement of shaft design/construction technology, and measurements for verification of the deep geological environment model estimated before shaft excavation, and it is on-going. This report summarizes the measurement plan during construction of drifts based on the design in advance and the observational construction program for feedback measurements data into design and construction on subsequent steps. This report also describes about design and construction management program of underground facility and R and D program on

Apparatus and method of measuring fluctuations of excavated mud amount in a slurry line

International Nuclear Information System (INIS)

Yamazaki, H.; Kubota, R.; Uchida, Y.; Kasuya, T.; Seki, N.

1976-01-01

An apparatus and method for measuring fluctuations in amount of soil in slurry or soil-containing fluid line is described. Each system of feeding the slurry typically to tunneling face and draining it therefrom in the slurry line is provided with gamma-ray densimeter and electromagnetic flow-meter to obtain respective amounts of soil only (dry-soil amounts) in the slurry flowing through each of said systems from respective outputs of these meters in each system, so that actually excavated amount through ground layer of a shielded excavator at the tunneling face can be measured by the difference between the respective dry-soil amounts. The excavator will be advanced depending on this measured amount

Excavation damage and disturbance in crystalline rock - results from experiments and analyses

International Nuclear Information System (INIS)

Baeckblom, Goeran

2008-11-01

SKB plans to submit the application to site and construct the final repository for spent nuclear fuel in 2010. One important basis for the application is the results of the safety assessments, for which one particular dataset is the axial hydraulic properties along the underground openings used to calculate the transport resistance for radionuclide transport in the event that the canister is impaired. SKB initiated a project (Zuse) to be run over the period 2007-2009 to: - establish the current knowledge base on excavation damage and disturbance with particular focus on the axial hydraulic properties along the underground openings; - provide a basis for the requirements and compliance criteria for the excavation damaged and disturbed zone; - devise methods and instruments to infer or measure the excavation damage and disturbance at different times during the repository construction and operation before closure; - propose demonstration tests for which the methods are used in situ to qualify appropriate data for use in the safety reports. This report presents the results of the first stage of the Zuse project. Previous major experiments and studies in Canada, Finland, Japan, Sweden and Switzerland on spalling, excavation damage and disturbance was compiled and evaluated to provide the SR-Site report with a defendable database on the properties for the excavation damage and disturbance. In preparation for the SR-Site report, a number of sensitivity studies were conducted in which reasonable ranges of values for spalling and damage were selected in combination with an impaired backfill. The report here describes the construction of the repository in eleven steps and for each of these steps, the potential evolution of THMCB (Thermal, Mechanical, Hydraulic and Chemical/ Biological) processes are reviewed. In this work it was found that descriptions of the chemical and microbiological evolution connected with excavation damage and disturbance was lacking. The preliminary

Physical soil properties and slope treatments effects on hydraulic excavator productivity for forest road construction.

Science.gov (United States)

Parsakho, Aidin; Hosseini, Seyed Ataollah; Jalilvand, Hamid; Lotfalian, Majid

2008-06-01

Effects of moisture, porosity and soil bulk density properties, grubbing time and terrain side slopes on pc 220 komatsu hydraulic excavator productivity were investigated in Miana forests road construction project which located in the northern forest of Iran. Soil moisture and porosity determined by samples were taken from undisturbed soil. The elements of daily works were measured with a digital stop watch and video camera in 14 observations (days). The road length and cross section profiles after each 20 m were selected to estimate earthworks volume. Results showed that the mean production rates for the pc 220 komatsu excavators were 60.13 m3 h(-1) and earthwork 14.76 m h(-1) when the mean depth of excavation or cutting was 4.27 m3 m(-1), respectively. There was no significant effects (p = 0.5288) from the slope classes' treatments on productivity, whereas grubbing time, soil moisture, bulk density and porosity had significantly affected on excavator earthworks volume (p < 0.0001). Clear difference was showed between the earthwork length by slope classes (p = 0.0060). Grubbing time (p = 0.2180), soil moisture (p = 0.1622), bulk density (p = 0.2490) and porosity (p = 0.2159) had no significant effect on the excavator earthworks length.

福建福鼎市太姥山宋代国兴寺遗址的发掘%Excavation of the Guoxingsi Temple-site of the Song Period at Tailaoshan in Fuding City,Fujian

Institute of Scientific and Technical Information of China (English)

福建博物院; 福鼎市文体局; 福鼎市旅游局; 太姥山风景区管理局

2003-01-01

In September-November 2001,the Fujian Provincial Museum and other institutions excavated the site of Guoxingsi Temple at Tailaoshan in Fuding City.They revealed the vestiges of pavilions,side rooms,passages,small yards and a stupa in this Song period temple and dug out large quantities of ceramic articles,structural members and inscribed steles.The excavation indicates that the temple was first built in the fourth year of the Qianfu reign,Tang Dynasty,and reached its prosperity atthe turn from the Northern Song to the Southern Song period.The unearthed material contributes to studying the history of architecture and Buddhism in ancient China.

Annual Report of Institute of Nuclear Chemistry and Technology 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

The report is the collection of short communications being the review of the scientific activity of Institute of Nuclear Chemistry and Technology - Warsaw in 1997. The papers are gathered in several branches as follows: radiation chemistry and physics; radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general; radiobiology; nuclear technologies and methods. The annual report of INCT-1997 contains also the general information about INCT as well as the full list of scientific papers being published by the staff in 1997

Annual Report of Institute of Nuclear Chemistry and Technology 1997

International Nuclear Information System (INIS)

1998-06-01

The report is the collection of short communications being the review of the scientific activity of Institute of Nuclear Chemistry and Technology - Warsaw in 1997. The papers are gathered in several branches as follows: radiation chemistry and physics; radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general; radiobiology; nuclear technologies and methods. The annual report of INCT-1997 contains also the general information about INCT as well as the full list of scientific papers being published by the staff in 1997

Annual Report of the Institute of Nuclear Chemistry and Technology 2000

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The INCT 2000 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics and nucleonic control systems and accelerators.

Annual Report of the Institute of Nuclear Chemistry and Technology 2000

International Nuclear Information System (INIS)

2001-06-01

The INCT 2000 Annual Report is the review of scientific activities in all branches being developed in the Institute of Nuclear Chemistry and Technology Warsaw. The studies are connected in general with the following fields: radiation chemistry and physics, radiation technologies, radiochemistry, stable isotopes, nuclear analytical methods, chemistry in general, radiobiology, process engineering, material engineering, structural studies and diagnostics and nucleonic control systems and accelerators

Harbin Institute of Technology collaborative base project at APS of Argonne

Science.gov (United States)

Liu, H.; Liu, L. L.

2013-05-01

In this paper, the progress of Harbin Institute of Technology (HIT) collaborative base project, which was launched at Argonne National Laboratory in 2010, will be presented. The staff and students from HIT involved in advanced technological developments, which included tomography, high energy PDF, diffraction and scattering, and inelastic scattering techniques in APS to study structures changes of minerals and materials under high pressure conditions.

The investigative training of teachers: an imperative for higher technological institute Ecuador

Directory of Open Access Journals (Sweden)

Belinda Marta Lema-Cachinell

2016-05-01

Full Text Available In work addresses some theoretical considerations - related methodological pedagogical and psychological research training budgets of teachers of technical and technological institutes, its foundations, characterizing the research training and how they are defined from educational policy , its components and features for the development of research skills in the process of training of technicians and technologists in the Commercial Institute of Technology and Vocational Training Administration and the importance to comprehensive training, as part of the changes that are experienced in higher education currently in the Ecuador , which must be analyzed in a broader dimension , not disjointed from the changes occurring in the world and the region.

Petroleum Science and Technology Institute with the TeXas Earth and Space Science (TXESS) Revolution

Science.gov (United States)

Olson, H. C.; Olson, J. E.; Bryant, S. L.; Lake, L. W.; Bommer, P.; Torres-Verdin, C.; Jablonowski, C.; Willis, M.

2009-12-01

The TeXas Earth and Space Science (TXESS) Revolution, a professional development program for 8th- thru 12th-grade Earth Science teachers, presented a one-week Petroleum Science and Technology Institute at The University of Texas at Austin campus. The summer program was a joint effort between the Jackson School of Geosciences and the Department of Petroleum and Geosystems Engineering. The goal of the institute was to focus on the STEM components involved in the petroleum industry and to introduce teachers to the larger energy resources theme. The institute kicked off with a welcoming event and tour of a green, energy-efficient home (LEED Platinum certified) owned by one of the petroleum engineering faculty. Tours of the home included an introduction to rainwater harvesting, solar energy, sustainable building materials and other topics on energy efficiency. Classroom topics included drilling technology (including a simulator lab and an overview of the history of the technology), energy use and petroleum geology, well-logging technology and interpretation, reservoir engineering and volumetrics (including numerous labs combining chemistry and physics), risk assessment and economics, carbon capture and storage (CO2 sequestration technology) and hydraulic fracturing. A mid-week field trip included visiting the Ocean Star offshore platform in Galveston, the Weiss Energy Hall at the Houston Museum of Science and Schlumberger (to view 3-D visualization technology) in Houston. Teachers remarked that they really appreciated the focused nature of the institute and especially found the increased use of mathematics both a tool for professional growth, as well as a challenge for them to use more math in their science classes. STEM integration was an important feature of the summer institute, and teachers found the integration of science (earth sciences, geophysics), technology, engineering (petroleum, chemical and reservoir) and mathematics particularly valuable. Pre

Excavation damage and disturbance in crystalline rock - results from experiments and analyses

Energy Technology Data Exchange (ETDEWEB)

Baeckblom, Goeran (Conrox AB, Stockholm (Sweden))

2008-11-15

SKB plans to submit the application to site and construct the final repository for spent nuclear fuel in 2010. One important basis for the application is the results of the safety assessments, for which one particular dataset is the axial hydraulic properties along the underground openings used to calculate the transport resistance for radionuclide transport in the event that the canister is impaired. SKB initiated a project (Zuse) to be run over the period 2007-2009 to: - establish the current knowledge base on excavation damage and disturbance with particular focus on the axial hydraulic properties along the underground openings; - provide a basis for the requirements and compliance criteria for the excavation damaged and disturbed zone; - devise methods and instruments to infer or measure the excavation damage and disturbance at different times during the repository construction and operation before closure; - propose demonstration tests for which the methods are used in situ to qualify appropriate data for use in the safety reports. This report presents the results of the first stage of the Zuse project. Previous major experiments and studies in Canada, Finland, Japan, Sweden and Switzerland on spalling, excavation damage and disturbance was compiled and evaluated to provide the SR-Site report with a defendable database on the properties for the excavation damage and disturbance. In preparation for the SR-Site report, a number of sensitivity studies were conducted in which reasonable ranges of values for spalling and damage were selected in combination with an impaired backfill. The report here describes the construction of the repository in eleven steps and for each of these steps, the potential evolution of THMCB (Thermal, Mechanical, Hydraulic and Chemical/ Biological) processes are reviewed. In this work it was found that descriptions of the chemical and microbiological evolution connected with excavation damage and disturbance was lacking. The preliminary

Stability calculation method of slope reinforced by prestressed anchor in process of excavation.

Science.gov (United States)

Li, Zhong; Wei, Jia; Yang, Jun

2014-01-01

This paper takes the effect of supporting structure and anchor on the slope stability of the excavation process into consideration; the stability calculation model is presented for the slope reinforced by prestressed anchor and grillage beam, and the dynamic search model of the critical slip surface also is put forward. The calculation model of the optimal stability solution of each anchor tension of the whole process is also given out, through which the real-time analysis and checking of slope stability in the process of excavation can be realized. The calculation examples indicate that the slope stability is changed with the dynamic change of the design parameters of anchor and grillage beam. So it is relatively more accurate and reasonable by using dynamic search model to determine the critical slip surface of the slope reinforced by prestressed anchor and grillage beam. Through the relationships of each anchor layout and the slope height of various stages of excavation, and the optimal stability solution of prestressed bolt tension design value in various excavation stages can be obtained. The arrangement of its prestressed anchor force reflects that the layout of the lower part of bolt and the calculation of slope reinforcement is in line with the actual. These indicate that the method is reasonable and practical.

Teaching Beliefs and Practice, Institutional Context, and the Uptake of Web-Based Technology

Science.gov (United States)

Lawrence, Belinda; Lentle-Keenan, Samantha

2013-01-01

This research examines the relationship between teaching beliefs and practice, institutional constraints, and the uptake of Web-based technology for teaching in higher education. Semistructured interviews were conducted with six teachers at a New Zealand tertiary institution. Using inductive analysis and cultural historical activity theory, themes…

Acoustic emission and ultrasonic-velocity methods used to characterise the excavation disturbance associated with deep tunnels in hard rock

Science.gov (United States)

Falls, Stephen D.; Young, R. Paul

1998-04-01

Acoustic emission (AE) and ultrasonic-velocity monitoring studies have been undertaken at both the Atomic Energy of Canada Limited (AECL) Underground Research Laboratory (URL) and at the Swedish Nuclear Fuel Waste Management Company (SKB) Hard Rock Laboratory (HRL). At both locations the excavations were tunnels in granitic material at approximately 420 m depth. However, the stress regime was more severe at the URL Mine-by tunnel site than the HRL ZEDEX tunnel. Different parts of the ZEDEX tunnel were created using different excavation techniques. Using AE and ultrasonic techniques to study these tunnels we have been able to examine the nature of the excavation-disturbed zone around the tunnel, as well as examining the effects of different stress regimes and excavation techniques. Studies were undertaken both during and after the Mine-by tunnel excavation and during excavation in the ZEDEX tunnel. AE monitoring in the wall of the Mine-by tunnel during excavation showed that some activity occurred in the sidewall regions, but the spatial density of AE hypocentres increased toward the regions in the floor and roof of the tunnel where breakout notches formed. This sidewall activity was clustered primarily within 0.5 m of the tunnel wall. AE monitoring in the floor of the tunnel showed that small numbers of AE continued to occur in the notch region in the floor of the tunnel over 2 years after excavation was completed. This activity became more acute as the rock was heated, imposing thermally induced stresses on the volume. Ultrasonic-velocity studies both in the floor and the wall of the tunnel showed that the velocity is strongly anisotropic with the direction of slowest velocity orthogonal to the tunnel surface. The velocity increased with distance into the rock from the tunnel surface. In the floor, this effect was seen up to 2 m from the tunnel surface. Most of the change occurred within the first 0.5 m from the tunnel perimeter. At the lower-stress HRL, most of

The SNL/NM Classified Waste Landfill Excavation: Lessons Learned Moving from Planning to Implementation

International Nuclear Information System (INIS)

Galloway, Robert B; Slavin, Paula

1999-01-01

The Sandia National Laboratories/New Mexico (SNL/NM) Environmental Restoration Project is halfway through excavating the Classified Waste Landfill in Technical Area II, a disposal area for weapon components for approximately 40 years. While the planning phase of any project is important, it is only a means of getting to the field implementation phase where reality quickly sinks in. Documents outlining the general processes are developed, heavy equipment, supply needs, requisite skills, and staffing levels are anticipated, and contingencies for waste management are put in place. However, the nature of landfill excavation dictates that even the most detailed plans will probably change. This project is proving that trying to account for undefined variables and predicting the total cost of landfill remediation is very difficult if the contents are not well known. In landfill excavation, contingency cannot be minimized. During development of the waste management plan, it was recognized that even the best forecasting could not formulate the perfect cradle-to-grave processes because waste streams are rarely definable before excavation begins. Typically, as excavation progresses and waste streams are generated, new characterization information allows further definition of disposal options which, in turn, modify the generation/management process. A general plan combined with close involvement of waste management personnel to resolve characterization and packaging questions during generation has worked very well. And, as expected, each new pit excavated creates new waste management challenges. The material excavated consists primarily of classified weapon assemblies and related components, so disposition must include demilitarization and sanitization. The demilitarization task at the start of the project was provided by an SNL/NM group that has since lost their funding and operational capability. This project is having to take on the task of disassembly, destruction, and

Excavation-drier method of energy-peat extraction reduces long-term climatic impact

Energy Technology Data Exchange (ETDEWEB)

Silvan, N.; Silvan, K.; Laine, J. [Finnish Forest Research Inst., Parkano (Finland)], e-mail: niko.silvan@metla.fi; Vaisanen, S.; Soukka, R. [Lappeenranta Univ.of Techology (Finland)

2012-11-01

Climatic impacts of energy-peat extraction are of increasing concern due to EU emissions trading requirements. A new excavation-drier peat extraction method has been developed to reduce the climatic impact and increase the efficiency of peat extraction. To quantify and compare the soil GHG fluxes of the excavation drier and the traditional milling methods, as well as the areas from which the energy peat is planned to be extracted in the future (extraction reserve area types), soil CO{sub 2}, CH{sub 4} and N{sub 2}O fluxes were measured during 2006-2007 at three sites in Finland. Within each site, fluxes were measured from drained extraction reserve areas, extraction fields and stockpiles of both methods and additionally from the biomass driers of the excavation-drier method. The Life Cycle Assessment (LCA), described at a principal level in ISO Standards 14040:2006 and 14044:2006, was used to assess the long-term (100 years) climatic impact from peatland utilisation with respect to land use and energy production chains where utilisation of coal was replaced with peat. Coal was used as a reference since in many cases peat and coal can replace each other in same power plants. According to this study, the peat extraction method used was of lesser significance than the extraction reserve area type in regards to the climatic impact. However, the excavation-drier method seems to cause a slightly reduced climatic impact as compared with the prevailing milling method. (orig.)

Experimental research data on stress state of salt rock mass around an underground excavation

Science.gov (United States)

Baryshnikov, VD; Baryshnikov, DV

2018-03-01

The paper presents the experimental stress state data obtained in surrounding salt rock mass around an excavation in Mir Mine, ALROSA. The deformation characteristics and the values of stresses in the adjacent rock mass are determined. Using the method of drilling a pair of parallel holes in a stressed area, the authors construct linear relationship for the radial displacements of the stress measurement hole boundaries under the short-term loading of the perturbing hole. The resultant elasticity moduli of rocks are comparable with the laboratory core test data. Pre-estimates of actual stresses point at the presence of a plasticity zone in the vicinity of the underground excavation. The stress state behavior at a distance from the excavation boundary disagrees with the Dinnik–Geim hypothesis.

System for the dissemination of innovative technological solutions at an R&D institute

Directory of Open Access Journals (Sweden)

Marzena Walasik

2013-06-01

Full Text Available The changes in the global market and the emphasis on the commercialization of R&D results, boost competitiveness and decide on the necessity to implement a marketing approach towards the organization and management of the business activity, including that of research institutions, which being treated as a unique kind of enterprises, make the results of their research commercially available. An important factor supporting effective commercialisation of research results is a proper preparation and execution of promotion activities, which based on the rules of marketing, increase the likelihood of success of implementation of innovative solutions on the market. The dissemination activities comprise all activities aimed at raising the interest of the public (i. e. users, enterprises, institutions in the results of R&D works, and focused on presenting the possibilities and benefits of their practical application. In order for the innovations to be diffused, target markets need to be specified, media most relevant for a given sector of the market need to be selected together with the most effective ways of reaching out to the target groups identified in the market segmentation process, and an effective marketing campaign needs to be launched. The system for the dissemination of innovative solutions developed and implemented at the Institute for Sustainable Technologies – National Research Institute in Radom (Poland (ITeE – PIB, supports the management of R&D results and stimulates networking between the Institute and entities involved in the practical implementation of innovations. It also enables the execution of system tasks concerning promotion of innovative product and process technologies developed at the ITeE – PIB. As a result of its application, business projects, which improve the technology commercialization process resulting in new products or technologies being brought to the market, are proposed.

Hydraulic tests for the Excavation Disturbed Zone in deep rock mass

International Nuclear Information System (INIS)

Matsuoka, Eiken

1998-03-01

Investigation for characterization of rock properties of the Excavation Disturbed Zone (EDZ) were carried out in 250 m level drift of KAMAISHI Mine. As a part of this investigation, hydraulic tests in the two different sections which were excavated by normal and smooth blasting method respectively, were performed in the vicinity of a drift wall and floor. The test results are as follows, 1) The distribution of pore water pressure in two sections was different. 2) In this investigation, hydraulic test was performed at the different depth in the horizontal and vertical down hole. The variation of measured permeability with depth from the drift wall and floor showed different character. 3) The measured permeability in horizontal hole has no change with depth from drift wall, but in vertical down hole, the measured permeability in nearest part from the floor indicated the higher value compared to the permeability in deeper part. 4) In horizontal holes in two sections there was no difference of the measured permeabilities dependent on the excavation method. The higher permeability was obtained in the vertical hole in smooth blasting section compared to normal blasting section. (author)

Alternatives to Industrial Work Placement at Dublin Institute of Technology

Science.gov (United States)

Bates, Catherine; Gamble, Elena

2011-01-01

In the current economic crisis, higher education graduates need transferable professional skills more than ever. They need resourcefulness, an ability to work reflectively, a sense of civic awareness and an impressive curriculum vitae. This case study analyses how Dublin Institute of Technology's Programme for Students Learning With Communities…

Selection of Excavators for Earth Work on the Basis of their Performance

Science.gov (United States)

Vondráčková, Terezie; Voštová, Věra

2017-10-01

For the specific construction of the reconstruction of the railway section Ostrov nad Oslavou and Žďár nad Sázavou will be done removed the railway superstructure and the partial adjustment of the substructure including drainage. For the earthwork will be used excavators of the company Komatsu, with the possibility of adjustment of parameters of the working tool - the length of the bracket and the volume of the shovel. The determined value will be purely indicative, as it does not affect how the operator of the excavator handles the discharge of cargo means.

The effect of deep excavation-induced lateral soil movements on the behavior of strip footing supported on reinforced sand

Directory of Open Access Journals (Sweden)

Mostafa El Sawwaf

2012-10-01

Full Text Available This paper presents the results of laboratory model tests on the influence of deep excavation-induced lateral soil movements on the behavior of a model strip footing adjacent to the excavation and supported on reinforced granular soil. Initially, the response of the strip footings supported on un-reinforced sand and subjected to vertical loads (which were constant during the test due to adjacent deep excavation-induced lateral soil movement were obtained. Then, the effects of the inclusion of geosynthetic reinforcement in supporting soil on the model footing behavior under the same conditions were investigated. The studied factors include the value of the sustained footing loads, the location of footing relative to the excavation, the affected depth of soil due to deep excavation, and the relative density of sand. Test results indicate that the inclusion of soil reinforcement in the supporting sand significantly decreases both vertical settlements and the tilts of the footings due to the nearby excavation. However, the improvements in the footing behavior were found to be very dependent on the location of the footing relative to excavation. Based on the test results, the variation of the footing measured vertical settlements with different parameters are presented and discussed.

Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

Technology selection for remediation of lead and hydrocarbon contaminated soil

International Nuclear Information System (INIS)

Richardson, K.E.; Sparks, G.M.

1993-01-01

This paper presents a methodology for selection of a technology for remediation of 70,000 tons of lead and hydrocarbon impacted soil resulting from an excavation at the Mobil Torrance Refinery. This methodology resulted from over two years of extensive research and technology evaluation. Twelve technologies and combination of technologies were evaluated, which often included bench scale testing, to determine the most cost effective and technically feasible remediation option. The results of the studies for each technology are discussed and presented in tabular form. The technologies investigated include: fixation/stabilization, soil washing, solvent washing, heap leach extraction, froth flotation, bioremediation, thermal desorption, electrokinetic extraction, asphalt incorporation, vitrification, off-site treatment, and off-site disposal. The associated costs and technical feasibility of each of the remediation options evaluated are presented. Laboratory analyses of the excavated soil indicate hydrocarbons range from non-detect to 11,000 ppm with an average of 2,600 ppm, soluble lead (CA test-not TCLP) range from 1.4 ppm to 100 ppm with an average of 29 ppm, and low levels of organic lead are present. Average grain size of the soil ranges from number-sign 200 to number-sign 120 mesh, and permeability averages 10--4 cm/sec. Significant odors, likely caused by hydrogen sulfide and thiophenes, were detected when the soil was excavated and control of odors during the remediation phase is a critical concern

MPED: An ISRU Bucket Ladder Excavator Demonstrator System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The proposed innovation is a planetary surface tool called the Multi Purpose Excavation Demonstrator (MPED), which is intended to both extract Lunar Soil to feed an...

Drill, baby, drill: the influence of woodpeckers on post-fire vertebrate communities through cavity excavation

Science.gov (United States)

Gina L. Tarbill; Patricia N. Manley; Angela M. White

2015-01-01

Several studies have addressed the importance of woodpeckers as ecological engineers in forests due to their excavation of cavities. Although research in green, unburned forests has identified the influence of different excavators on secondary use by cavity-dependent species, little is known about the relative importance of cavities created by woodpeckers in recently...

The Method of Validity Evaluation of Hard Coal Excavation in Residual Seam Parts

Science.gov (United States)

Wodarski, Krzysztof; Bijańska, Jolanta; Gumiński, Adam

2017-12-01

The excavation of residual seam parts should be justified by positive assessment of the purposefulness, technical feasibility and economic effectiveness. The results of the profitability evaluation are crucial in a decision making process. The excavation of residual seam parts, even if it is possible from a technical point of view, should not be implemented if it is economically inefficient or when accompanied by a very high risk of non-recovery of invested capital resources. The article presents the evaluation method of possibilities of excavating hard coal from residual seam parts, and the example of its use in one of collieries in the Upper Silesian Coal Basin. Working in line with the developed method, allows to indicate the variant of residual seam part exploitation, which is feasible to implement from a technical point of view, and which is characterized by the highest economic effectiveness and lowest risk.

Archaeological excavation of T10/993 at Matarangi

International Nuclear Information System (INIS)

Furey, L.

1999-01-01

This report describes the excavation of a small midden site, T10/993, representative of a number of like sites in the sand dunes at Matarangi on the east coast of the Coromandel Peninsula. Few sites of this type have been investigated archaeologically yet they are the remains of a very important part of the Maori economic cycle. The sites could be termed shellfish processing sites. The excavation was a condition imposed by Historic Places Trust on the granting of an authority to modify sites T10/993 and 994 (HPT Authority no. 1997/42), prior to destruction of the sites (Furey 1998). Matarangi Beach Estates commissioned the author to undertake an archaeological site survey of a grassed area at Matarangi Beach which was to be Stage 14 of the urban housing development. The area was in excess of 13 hectares. Two sites were found, T10/993 and 994, and recommendations made for monitoring of the dunes as the topsoil was removed (Furey 1997a). (author). 15 refs., 6 figs., 2 tabs

Joint ANDRA/Nirex/SKB zone of excavation disturbance experiment (ZEDEX) at the Aspo hard rock laboratory

International Nuclear Information System (INIS)

Hooper, A.J.; Olsson, O.

1995-01-01

The excavation of access shafts and tunnels and of the disposal areas of a waste repository will cause a disturbance in the surrounding rock mass with possible alterations to rock mass stability and hydraulic properties. For a number of disposal concepts this disturbance may be important for the operational and/or post-closure safety of the repository. Furthermore the disturbance may extend over time as a consequence of processes such as stress relaxation. The sponsors of ZEDEX, namely ANDRA, Nirex and SKB, are interested in developing the ability to produce reliable models of the disturbed zone that will develop around large cross-section excavations in fractured hard rock masses that are initially water saturated. Various models have been developed to calculate the important characteristics of the disturbed zone in such rock masses as a function of parameters related to the rock mass quality and the geometric description of the excavation. ZEDEX was initiated in the Aspo Hard Rock Laboratory in April 1994 with drilling and instrumentation of boreholes running alongside the planned extension of the spiral access ramp and a planned parallel experimental tunnel. ZEDEX has been designed to generate information for alternative methods of excavation. The extension to the spiral ramp is to be made by tunnel boring whereas the parallel experimental tunnel will be excavated in part by ''normal'' basting and in part by smooth blasting. The objective is to build confidence in the modelling of the disturbed zone to support the selection of excavation methods for repository construction. (authors). 3 figs

Numerical Simulation of Rock Mass Damage Evolution During Deep-Buried Tunnel Excavation by Drill and Blast

Science.gov (United States)

Yang, Jianhua; Lu, Wenbo; Hu, Yingguo; Chen, Ming; Yan, Peng

2015-09-01

Presence of an excavation damage zone (EDZ) around a tunnel perimeter is of significant concern with regard to safety, stability, costs and overall performance of the tunnel. For deep-buried tunnel excavation by drill and blast, it is generally accepted that a combination of effects of stress redistribution and blasting is mainly responsible for development of the EDZ. However, few open literatures can be found to use numerical methods to investigate the behavior of rock damage induced by the combined effects, and it is still far from full understanding how, when and to what degree the blasting affects the behavior of the EDZ during excavation. By implementing a statistical damage evolution law based on stress criterion into the commercial software LS-DYNA through its user-subroutines, this paper presents a 3D numerical simulation of the rock damage evolution of a deep-buried tunnel excavation, with a special emphasis on the combined effects of the stress redistribution of surrounding rock masses and the blasting-induced damage. Influence of repeated blast loadings on the damage extension for practical millisecond delay blasting is investigated in the present analysis. Accompanying explosive detonation and secession of rock fragments from their initial locations, in situ stress in the immediate vicinity of the excavation face is suddenly released. The transient characteristics of the in situ stress release and induced dynamic responses in the surrounding rock masses are also highlighted. From the simulation results, some instructive conclusions are drawn with respect to the rock damage mechanism and evolution during deep-buried tunnel excavation by drill and blast.

Optics and communication technology major of physics undergraduate degree at King Mongkut's Institute of Technology Ladkrabang

Science.gov (United States)

Buranasiri, Prathan

2014-09-01

A physics undergraduate degree major in optics and communication technology has been offered at King Mongkut's Institute of Technology Ladkrabang (KMITL), Bangkok, Thailand. There are nine required three credit hour courses including two laboratory courses plus a number of selections in optics and communication based technology courses. For independent thinking and industrial working skills, nine credit hours of research project, practical training or overseas studies are included for selection in the final semester. Students are encouraged to participate in international conferences and professional organizations. Recently the program, with support from SPIE and OSA, has organized its first international conference on photonic solutions 2013 (ICPS 2013).

On the Cutting Edge: Movements and Institutional Examples of Technological Disruption

Science.gov (United States)

Leon, Marjorie Roth; Price, Todd Alan

2016-01-01

This chapter describes technological disruptions in higher education that pose challenges and offer opportunities to college and university students, faculty, and administrators. It provides examples of innovative responses being explored by 2-year and 4-year higher education institutions.

The Excavation and Remediation of the Sandia National Laboratories Chemical Waste Landfill

International Nuclear Information System (INIS)

KWIECINSKI, DANIEL ALBERT; METHVIN, RHONDA KAY; SCHOFIELD, DONALD P.; YOUNG, SHARISSA G.

1999-01-01

The Chemical Waste Landfill (CWL) at Sandia National Laboratories/New Mexico (SNL/NM) is a 1.9-acre disposal site that was used for the disposal of chemical wastes generated by many of SNL/NM research laboratories from 1962 until 1985. These laboratories were primarily involved in the design, research and development of non-nuclear components of nuclear weapons and the waste generated by these labs included small quantities of a wide assortment of chemical products. A Resource Conservation and Recovery Act (RCRA) Closure Plan for the Chemical Waste Landfill was approved by the New Mexico Environment Department (NMED) in 1992. Subsequent site characterization activities identified the presence of significant amounts of chromium in the soil as far as 80 feet below ground surface (fbgs) and the delineation of a solvent plume in the vadose zone that extends to groundwater approximately 500 fbgs. Trichloroethylene (TCE) was detected in some groundwater samples at concentrations slightly above the drinking water limit of 5 parts per billion. In 1997 an active vapor extraction system reduced the size of the TCE vapor plume and for the last six quarterly sampling events groundwater samples have not detected TCE above the drinking water standard. A source term removal, being conducted as a Voluntary Corrective Measure (VCM), began in September 1998 and is expected to take up to two years. Four distinct disposal areas were identified from historical data and the contents of disposal pits and trenches in these areas, in addition to much of the highly contaminated soil surrounding the disposal cells, are currently being excavated. Buried waste and debris are expected to extend to a depth of 12 to 15 fbgs. Excavation will focus on the removal of buried debris and contaminated soil in a sequential, area by area manner and will proceed to whatever depth is required in order to remove all pit contents. Up to 50,000 cubic yards of soil and debris will be removed and managed during

Transition of the Course Programs in the 40 Years History of Hitachi Institute of Technology

Science.gov (United States)

Miura, Osamu; Katsura, Koyo; Takahashi, Masahiko

In 2010, the Hitachi Institute of Technology reached the 40th anniversary. In the beginning, the institute stood at the product-out-oriented view point and carried out extensive technical education from basis to advanced technology. After the 1990s, transition of the business environment with the globalization caused that the needs of the engineer education required by the business sections have been transformed. As the result, the changes of needs have been reflected for course program of the institute. Nowadays, in addition to the conventional course programs, the engineer education programs for the business competency and human skill have also been focused.

Modelling bucket excavation by finite element

Science.gov (United States)

Pecingina, O. M.

2015-11-01

Changes in geological components of the layers from lignite pits have an impact on the sustainability of the cup path elements and under the action of excavation force appear efforts leading to deformation of the entire assembly. Application of finite element method in the optimization of components leads to economic growth, to increase the reliability and durability of the studied machine parts thus the machine. It is obvious usefulness of knowledge the state of mechanical tensions that the designed piece or the assembly not to break under the action of tensions that must cope during operation. In the course of excavation work on all bucket cutting force components, the first coming into contact with the material being excavated cutting edge. Therefore in the study with finite element analysis is retained only cutting edge. To study the field of stress and strain on the cutting edge will be created geometric patterns for each type of cup this will be subject to static analysis. The geometric design retains the cutting edge shape and on this on the tooth cassette location will apply an areal force on the abutment tooth. The cutting edge real pattern is subjected to finite element study for the worst case of rock cutting by symmetrical and asymmetrical cups whose profile is different. The purpose of this paper is to determine the displacement and tensions field for both profiles considering the maximum force applied on the cutting edge and the depth of the cutting is equal with the width of the cutting edge of the tooth. It will consider the worst case when on the structure will act both the tangential force and radial force on the bucket profile. For determination of stress and strain field on the form design of cutting edge profile will apply maximum force assuming uniform distribution and on the edge surface force will apply a radial force. After geometric patterns discretization on the cutting knives and determining stress field, can be seen that at the

Predictive modelling of an excavation test in indurated clay

International Nuclear Information System (INIS)

Garitte, B.; Vaunat, J.; Gens, A.; Vietor, T.

2010-01-01

Document available in extended abstract form only. This Abstract presents the predictive hydro-mechanical (HM) modelling of an excavation performed in Opalinus clay in the Mont Terri underground laboratory. Niche 2 was excavated in the shaly facies of Opalinus clay from gallery 08. The area surrounding the gallery was intensively instrumented. The geology of Mont Terri is described in Thury and Bosssart (1999) and the parameters used in the analysis were taken from Bock (2009). The stress state is derived from Martin and Lanyion (2003). Gallery 08 is horseshoe shaped and has a mean radius of 2.25 m. It was excavated with a road header at a mean velocity of 1 m/day starting on January 30, 2008 (Gallery chainage 43.8) and ending on June 30, 2008 (Gallery chainage 123.8) with a stop from March 18, to April 24, to instrument the area of niche 2. Niche 2 was excavated by successive blastings 1.3 m deep until reaching a distance of 24 m from the gallery 08 wall. Advance was continuous from October 13, to November 7 with the exception of three stops of 3, 5 and 4 days. The niche has an average diameter of 4.5 m and has a slight upward slope of 0.98%. The excavation of gallery 08 from chainage 43.8 to chainage 123.8 and of the niche was simulated by relaxing the normal total stress and water pressure from the value before excavation to 0. The gallery advance rate was simulated in an approximate manner by applying successively the excavation procedure to 9 m long gallery sections. In the case of the niche, the blasting scheme and the application of the shotcrete was closely reproduced. The three dimensional geometry used in the simulation is shown. The coupled hydro-mechanical formulation used for the analysis is based on the simultaneous solution of the balance equation for solid mass, water mass and momentum (equilibrium). In accordance with field observations, it has been assumed that the medium remains saturated throughout. The formulation was completed with a number of

Remote Excavation of Heavily Contaminated UXO Sites. The Range Master

National Research Council Canada - National Science Library

Crandall, Alan L

2007-01-01

USA Environmental, Inc., and Timberline Environmental Services, Inc., developed the Range Master, a remote controlled scraper with an integrated power screen, to excavate and sift the top 12 inches of heavily contaminated UXO sites...

Archaeological Studies of the Ancient Turkestan Site: results of 2011-2012 excavations

Directory of Open Access Journals (Sweden)

Smagulov Yerbulat A.

2013-03-01

Full Text Available The results of the 2011-12 excavations on the Eski-Turkestan site conducted by the Turkestani archaeological expedition (Institute of archaeology named after A. Margulan are presented. The site contains the remains of the ancient town of Yasy (modern town of Turkestan, South Kazakhstan oblast. The aim of the excavations was to study the earliest layers of the settlement, the primary stages of the city formation, and to identify construction elements of the ancient citadel in particular. It has been established that the most ancient nucleus of the city was located under Kultobe hill on the eastern edge of the settlement. The oldest architectural object of the citadel is a cruciform construction with powerful rammed clay defensive walls having narrow loopholes, preserved to a height of over 3 m. The three rooms were connected by arched doorways. In the second construction horizon, a building with long narrow rooms around a small open courtyard had been added to this "castle". During this period, around the perimeter of the citadel powerful rammed clay and mud-brick defensive walls had been erected, with the space between them and the extended castle being just partially built up. These two periods can be dated to the 1st–3rd centuries AD. This stage comes to an end with defeat and a fire. In the fire layer, numerous ceramic vessels in disassembling have been found. Individual unique finds have been made, and alabaster idols are of special interest. The restoration of the fortification wall and a new stage of the citadel development refer to the 9th-11th centuries. At the base of the new wall, pots with sacrificial food have been discovered, one of them bearing a runic inscription.

Robotic excavator trajectory control using an improved GA based PID controller

Science.gov (United States)

Feng, Hao; Yin, Chen-Bo; Weng, Wen-wen; Ma, Wei; Zhou, Jun-jing; Jia, Wen-hua; Zhang, Zi-li

2018-05-01

In order to achieve excellent trajectory tracking performances, an improved genetic algorithm (IGA) is presented to search for the optimal proportional-integral-derivative (PID) controller parameters for the robotic excavator. Firstly, the mathematical model of kinematic and electro-hydraulic proportional control system of the excavator are analyzed based on the mechanism modeling method. On this basis, the actual model of the electro-hydraulic proportional system are established by the identification experiment. Furthermore, the population, the fitness function, the crossover probability and mutation probability of the SGA are improved: the initial PID parameters are calculated by the Ziegler-Nichols (Z-N) tuning method and the initial population is generated near it; the fitness function is transformed to maintain the diversity of the population; the probability of crossover and mutation are adjusted automatically to avoid premature convergence. Moreover, a simulation study is carried out to evaluate the time response performance of the proposed controller, i.e., IGA based PID against the SGA and Z-N based PID controllers with a step signal. It was shown from the simulation study that the proposed controller provides the least rise time and settling time of 1.23 s and 1.81 s, respectively against the other tested controllers. Finally, two types of trajectories are designed to validate the performances of the control algorithms, and experiments are performed on the excavator trajectory control experimental platform. It was demonstrated from the experimental work that the proposed IGA based PID controller improves the trajectory accuracy of the horizontal line and slope line trajectories by 23.98% and 23.64%, respectively in comparison to the SGA tuned PID controller. The results further indicate that the proposed IGA tuning based PID controller is effective for improving the tracking accuracy, which may be employed in the trajectory control of an actual excavator.

Characteristics of the excavation response zone as applied to shaft sealing

International Nuclear Information System (INIS)

Jakubick, A.T.; Klein, R.; Gray, M.N.; Keil, L.D.

1989-01-01

Effective sealing of an underground repository requires high quality seals. Clay-based backfills in combination with cement plugs are the possible candidates. An important component of the shaft sealing program is the development of techniques to predict and monitor the flow in the excavation response zone (ERZ) and at the seal-rock interface. The mechanical and hydraulic performance of the seal and backfill and the flow characteristics of the ERZ under in situ conditions will be tested in three experimental shafts to be excavated in the URL. The use of the vacuum permeability technique for characterization of the hydraulic properties and of the permeability distribution in the ERZ under various geomechanical conditions is discussed

Interaction Deep Excavation Adjacent Structure Numerical Two and Three Dimensional Modeling

International Nuclear Information System (INIS)

Abdallah, M.; Chehade, F. H.; Chehade, W.; Fawaz, A.

2011-01-01

Urban development often requires the construction of deep excavations near to buildings or other structures. We have to study complex material structure interactions where we should take into consideration several particularities. In this paper, we perform a numerical modeling with the finite element method, using PLAXIS software, of the interaction deep excavation-diaphragm wall-soil-structure in the case of non linear soil behavior. We focus our study on a comparison of the results given respectively by two and three dimensional modelings. This allows us to give some recommendations concerning the validity of twodimensional study. We perform a parametric study according to the initial loading on the structure and the struts number. (author)

CLASSIFICATION OF THE MGR SUBSURFACE EXCAVATION SYSTEM

International Nuclear Information System (INIS)

R. Garrett

1999-01-01

The purpose of this analysis is to document the Quality Assurance (QA) classification of the Monitored Geologic Repository (MGR) subsurface excavation system structures, systems and components (SSCs) performed by the MGR Safety Assurance Department. This analysis also provides the basis for revision of YMP/90-55Q, Q-List (YMP 1998). The Q-List identifies those MGR SSCs subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description'' (QARD) (DOE 1998)

A Comparative Evaluation of the Efficacy of Different Caries Excavation Techniques in reducing the Cariogenic Flora: An in vivo Study.

Science.gov (United States)

Hassan, Afrah Fatima; Yadav, Gunjan; Tripathi, Abhay Mani; Mehrotra, Mridul; Saha, Sonali; Garg, Nishita

2016-01-01

Caries excavation is a noninvasive technique of caries removal with maximum preservation of healthy tooth structure. To compare the efficacy of three different caries excavation techniques in reducing the count of cariogenic flora. Sixty healthy primary molars were selected from 26 healthy children with occlusal carious lesions without pulpal involvement and divided into three groups in which caries excavation was done with the help of (1) carbide bur; (2) polymer bur using slow-speed handpiece; and (3) ultrasonic tip with ultrasonic machine. Samples were collected before and after caries excavation for microbiological analysis with the help of sterile sharp spoon excavator. Samples were inoculated on blood agar plate and incubated at 37°C for 48 hours. After bacterial cultivation, the bacterial count of Streptococcus mutans was obtained. All statistical analysis was performed using SPSS 13 statistical software version. Kruskal-Wallis analysis of variance, Wilcoxon matched pairs test, and Z test were performed to reveal the statistical significance. The decrease in bacterial count of S. mutans before and after caries excavation was significant (p flora, while ultrasonic tip showed almost comparable results, while polymer bur showed least reduction in cariogenic flora after caries excavation. Hassan AF, Yadav G, Tripathi AM, Mehrotra M, Saha S, Garg N. A Comparative Evaluation of the Efficacy of Different Caries Excavation Techniques in reducing the Cariogenic Flora: An in vivo Study. Int J Clin Pediatr Dent 2016;9(3):214-217.

The influence of cathode excavation of cathodic arc evaporator on thickness uniformity and erosion products angle distribution

Directory of Open Access Journals (Sweden)

D. V. Duhopel'nikov

2014-01-01

Full Text Available Cathodic arc evaporators are used for coating with functional films. Prolonged or buttend evaporators may be used for this purposes. In butt-end evaporator the cathode spots move continuously on the cathode work surface and evaporate cathode material. High depth excavation profile forms on the cathode work surface while the thick coating precipitation (tens or hundreds of microns. The cathode excavation profile is shaped like a “cup” with high walls for electrostatic discharge stabilization systems with axial magnetic fields. Cathode spots move on the bottom of the “cup”. It is very likely that high “cup” walls are formed as a result of lasting work time influence on the uniformity of precipitated films.In the present work the influence of excavation profile walls height on the uniformity of precipitated coating was carried out. The high profile walls are formed due to lasting work of DC vacuum arc evaporator. The cathode material used for tests was 3003 aluminum alloy. The extended substrate was placed parallel to the cathode work surface. Thickness distribution along the substrate length with the new cathode was obtained after 6 hours and after 12 hours of continuous operation.The thickness distribution of precipitated coating showed that the cathode excavation has an influence on the angular distribution of the matter escaping the cathode. It can be clearly seen from the normalized dependence coating thickness vs the distance from the substrate center. Also the angular distribution of the matter flow from the cathode depending on the cathode working time was obtained. It was shown that matter flow from the cathode differs from the LambertKnudsen law. The more the cathode excavation the more this difference.So, cathode excavation profile has an influence on the uniformity of precipitated coating and it is necessary to take in account the cathode excavation profile while coating the thick films.

The Historically Black Colleges and Universities/Minority Institutions Environmental Technology Consortium annual report 1994--1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The HBCU/MI ET Consortium was established in January 1990, through a Memorandum of Understanding (MOU) among its member institutions. This group of research oriented Historically Black Colleges and Universities and Minority Institutions (HBCU/MIs) agreed to work together to initiate or revise education programs, develop research partnerships with public and private sector organizations, and promote technology development to address the nation`s critical environmental contamination problems. The Consortium`s Research, Education and Technology Transfer (RETT) Plan became the working agenda. The Consortium is a resource for collaboration among the member institutions and with federal an state agencies, national and federal laboratories, industries, (including small businesses), majority universities, and two and four-year technical colleges. As a group of 17 institutions geographically located in the southern US, the Consortium is well positioned to reach a diverse group of women and minority populations of African Americans, Hispanics and American Indians. This Report provides a status update on activities and achievements in environmental curriculum development, outreach at the K--12 level, undergraduate and graduate education, research and development, and technology transfer.

The modern water-saving agricultural technology: Progress and focus

African Journals Online (AJOL)

GREGORY

2010-09-13

Sep 13, 2010 ... DEVELOPING TENDENCY OF MODERN WATER-. SAVING AGRICULTURAL TECHNOLOGY. Excavation of the own water-saving potential using biotechnology. The biological water-saving technology that uses crop physiology control and modern breeding techniques to increase production and water ...

Evolution of technology convergence networks in Korea: Characteristics of temporal changes in R&D according to institution type

Science.gov (United States)

Choi, Jae Young; Jeong, Seongkyoon

2018-01-01

This study investigates the temporal changes in development of technology convergence networks by institution type, i.e., public research institute (PRI), university and industry. Using the co-classification of technological domains of patents, we identified technology convergence of Korean patents, which were filed at Korea Intellectual Properties Office (KIPO) from 1997 to 2011. We conducted a network analysis at the technology level to search for the key technology fields and frequent instances of technology convergence. The results show that technology convergence networks have grown significantly in the recent period regardless of the institution type. While industries started to conspicuously engage in technology convergence in the late 1990s, universities or PRIs did not do so until the mid-2000s. This discrepancy in the phase of technology convergence is attributed to the temporal difference in R&D stage (e.g., basic research and commercial product development). Our findings imply that corporal and governmental R&D management decision on promising technology fields will be more effective if the decision makers carefully consider the type of R&D entity in analyzing technological landscapes. PMID:29420574

Evolution of technology convergence networks in Korea: Characteristics of temporal changes in R&D according to institution type.

Science.gov (United States)

Choi, Jae Young; Jeong, Seongkyoon; Jung, Jung-Kyu

2018-01-01

This study investigates the temporal changes in development of technology convergence networks by institution type, i.e., public research institute (PRI), university and industry. Using the co-classification of technological domains of patents, we identified technology convergence of Korean patents, which were filed at Korea Intellectual Properties Office (KIPO) from 1997 to 2011. We conducted a network analysis at the technology level to search for the key technology fields and frequent instances of technology convergence. The results show that technology convergence networks have grown significantly in the recent period regardless of the institution type. While industries started to conspicuously engage in technology convergence in the late 1990s, universities or PRIs did not do so until the mid-2000s. This discrepancy in the phase of technology convergence is attributed to the temporal difference in R&D stage (e.g., basic research and commercial product development). Our findings imply that corporal and governmental R&D management decision on promising technology fields will be more effective if the decision makers carefully consider the type of R&D entity in analyzing technological landscapes.

Review of excavation methods and their implications for the near-field barrier of a deep underground repository

International Nuclear Information System (INIS)

Young, D.K.

1993-01-01

The report reviews excavation techniques for use in the construction of deep underground radioactive waste repositories, gives a summary of responses of the host rock to excavation and the means of measuring that response and discusses techniques for predicting that response. The review of excavation techniques included technical developments and current practice. To this end an extensive database was developed reviewing major excavations in rock types relevant to disposal and the techniques employed. Creation of an underground opening alters the properties of the rock mass around it. This study identifies stress, displacement, rock mass deformability and permeability as key parameters and reviews how they may be determined. Finally the report discusses the techniques available for predicting the behaviour of the near-field host rock. This concentrates on methods of numerical analysis since existing empirical or analytical methods are not considered suitable. (author)

MARSAME Radiological Release Report for Archaeological Artifacts Excavated from Area L

Energy Technology Data Exchange (ETDEWEB)

Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Whicker, Jeffrey Jay [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gillis, Jessica Mcdonnel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-03

In 1991 Los Alamos National Laboratory’s (LANL’s) cultural resources team excavated archaeological site LA 4618 located at Technical Area 54, within Material Disposal Area L (MDA L). MDA L received non-radioactive chemical waste from the early 1960s until 1985. Further development of the MDA required excavation of several cultural sites under National Historic Preservation Act requirements; artifacts from these sites have been subsequently stored at LANL. The LANL cultural resources group would now like to release these artifacts to the Museum of Indian Arts and Culture in Santa Fe for curation. The history of disposal at Area L suggests that the artifact pool is unlikely to be chemically contaminated and LANL staff washed each artifact at least once following excavation. Thus, it is unlikely that the artifacts present a chemical hazard. LANL’s Environmental Stewardship group (EPC-ES) has evaluated the radiological survey results for the Area L artifact pool and found that the items described in this report meet the criteria for unrestricted radiological release under Department of Energy (DOE) Order 458.1 Radiation Protection of the Public and the Environment and are candidates for release without restriction from LANL control. This conclusion is based on the known history of MDA L and on radiation survey data.

DEM modeling of failure mechanisms induced by excavations on the Moon

Science.gov (United States)

jiang, mingjing; shen, zhifu; Utili, Stefano

2013-04-01

2D Discrete Element Method (DEM) analyses were performed for excavations supported by retaining walls in lunar environment. The lunar terrain is made of a layer of sand (regolith) which differs from terrestrial sands for two main features: the presence of adhesive attractive forces due to van der Waals interactions and grains being very irregular in shape leading to high interlocking. A simplified contact model based on linear elasticity and perfect plasticity was employed. The contact model includes a moment - relative rotation law to account for high interlocking among grains and a normal adhesion law to account for the van der Waals interactions. Analyses of the excavations were run under both lunar and terrestrial environments. Under lunar environment, gravity is approximately one sixth than the value on Earth and adhesion forces between grains of lunar regolith due to van der Waals interactions are not negligible. From the DEM simulations it emerged that van der Waals interactions may significantly increase the bending moment and deflection of the retaining wall, and the ground displacements. Hence this study indicates that an unsafe estimate of the wall response to an excavation on the Moon would be obtained from physical experiments performed in a terrestrial environment, i.e., considering the effect of gravity but neglecting the van der Waals interactions.

Long-term monitoring of rock mass properties in the underground excavation

Science.gov (United States)

Vilhelm, Jan; Jirků, Jaroslav; Slavík, Lubomír; Bárta, Jaroslav

2015-04-01

It is generally agreed today that hazardous waste should be placed in repositories hundreds of meters below the Earth's surface. In our research we deal with the long-term monitoring of the underground excavation by seismic and electrical resistivity measurements. Permanent measuring system was developed and installed at the Bedřichov gallery test site (northern Bohemia). The gallery was excavated using TBM (Tunnel Boring Machine) in granitic rocks. Realized repeated measurements include ultrasonic time of flight measurement and electrical resistivity tomography (ERT). The seismic measurements are performed by pulse-transmission technique directly on the rock wall using one seismic source and three receivers in the distances of 1, 2 and 3 m. The main emphasis is devoted to P-waves; however, recording of full waveform enables analyzing of S- waves and other types of waves as well. The comparison of repeated measurements is used for an assessment of changes in seismic velocities with very high-accuracy. The repetition rate of measurements can be selected from seconds; however such fast changes in the rock mass are unexpected. The ERT measurement is performed on the same rock wall using 48 electrodes. The spacing between electrodes is 20 centimeters. The conductivity of undisturbed granitic rocks is extremely low. Therefore the observed local increase of conductivity can be associated with joints and fractures saturated with water, resulting in their ionic conductivity. Repeated ERT measurement can reveal some changes in the rock mass. Due to time requirements of ERT measurement the repetition rate can be about three hours. The data collected by measuring system is transferred by means of computer network and can be accessed via internet. This contribution deals with preliminary results gained so far during the testing of developed monitoring system. Acknowledgments: This work was partially supported by the Technology Agency of the Czech Republic, project No. TA

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

Toxic hazards of underground excavation

International Nuclear Information System (INIS)

Smith, R.; Chitnis, V.; Damasian, M.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards

Toxic hazards of underground excavation

Energy Technology Data Exchange (ETDEWEB)

Smith, R.; Chitnis, V.; Damasian, M.; Lemm, M.; Popplesdorf, N.; Ryan, T.; Saban, C.; Cohen, J.; Smith, C.; Ciminesi, F.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards.

Critical Success in E-learning: An Examination of Technological and Institutional Support Factors

Directory of Open Access Journals (Sweden)

Maslin Masrom

2008-12-01

Full Text Available In recent years, information technology (IT becomes prominent to support teaching and learning activities. IT tools allow us to create, collect, store and use the information and knowledge. E-learning was one of IT tools introduced at College of Science and Technology (CST, University Technology Malaysia (UTM Kuala Lumpur since 2001. It has enabled a paradigm shift from institutio n-centered instruction to anywhere, anytime and anybody learning models. In CST the e-learning technology was used for accessing the syllabus and course content, submitting assignments, and taking class quizzes. This paper focuses on issues relating to the e-learning critical success factors (CSFs from university students’ perspective. In this study, two main factors related to the e-learning CSFs within a university environment included technological and institutional support factors were examined. Confirmatory factor modeling approach was used to assess the criticality of the measures included in each factor. The results indicated that the most critical measures for technological factor in terms of ease of access and infrastructure are the browser efficiency, course website ease of use and computer network reliability. Meanwhile, for institutional support factor, the most critical measure is the availability of technical support or help desk.

Grimsel test site. Excavation disturbed zone experiment (EDZ)

International Nuclear Information System (INIS)

Frieg, B.; Blaser, P. C.; Adams, J.; Dollinger, H.; Kuhlmann, U.; Lanyon, G. W.

2012-07-01

The ‘Excavation Disturbed Zone (EDZ) Experiment’ was conducted at the Grimsel Test Site (GTS) in the framework of safety analysis of deep geological repositories for radioactive wastes. It concentrated on investigating the hydraulic regime of the near-field of drilled tunnel sections under fully saturated conditions, with the aim of contributing to the development of methods for measuring and modelling axial water flow along tunnels and caverns. The studies focused on the mechanical and hydraulic properties of the rock mass in the direct vicinity of the tunnel wall. The EDZ is defined as the zone around the tunnel where excavation has altered the rock properties. The selected test location was a tunnel section where mechanical stressing of the rock and some breakouts had been observed. In-situ stress measurements were performed in order to record the actual stress redistribution in the tunnel near-field induced by excavation of the tunnel. A small stress increase and microfissures could be identified in the tunnel near-field. The stress measurements and the results of the geological mapping formed the basis for the rock mechanical modelling of the EDZ. Two different models of the development and geometry of the EDZ were used: (a) the regional 3D stress field modelling indicated that the topography has a significant influence on the primary stress field; a good agreement between the measured and calculated stresses in the GTS was achieved by applying an additional far-field tectonic stress component; (b) with the local 2D numerical disturbed zone modelling of the tunnel section itself, stress redistributions, possible plastifications and joint behaviour were investigated; all displacements of the rock matrix and the shear displacements of the discontinuities seem to be the result of the tunnel excavation; maximum shear deformations of 2 - 5 mm occur at the tunnel wall. Prior to the hydraulic test phase, the test location was decoupled from the normal GTS tunnel

A research on the excavation, support, and environment control of large scale underground space

Energy Technology Data Exchange (ETDEWEB)

Kang, Pil Chong; Kwon, Kwang Soo; Jeong, So Keul [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

With the growing necessity of the underground space due to the deficiency of above-ground space, the size and shape of underground structures tend to be complex and diverse. This complexity and variety force the development of new techniques for rock mass classification, excavation and supporting of underground space, monitoring and control of underground environment. All these techniques should be applied together to make the underground space comfortable. To achieve this, efforts have been made on 5 different areas; research on the underground space design and stability analysis, research on the techniques for excavation of rock by controlled blasting, research on the development of monitoring system to forecast the rock behaviour of underground space, research on the environment inspection system in closed space, and research on dynamic analysis of the airflow and environmental control in the large geos-spaces. The 5 main achievements are improvement of the existing structure analysis program(EXCRACK) to consider the deformation and failure characteristics of rock joints, development of new blasting design (SK-cut), prediction of ground vibration through the newly proposed wave propagation equation, development and In-Situ application of rock mass deformation monitoring system and data acquisition software, and trial manufacture of the environment inspection system in closed space. Should these techniques be applied to the development of underground space, prevention of industrial disaster, cut down of construction cost, domestication of monitoring system, improvement of tunnel stability, curtailment of royalty, upgrade of domestic technologies will be brought forth. (Abstract Truncated)

Results of research and development activities in 1989 of the Institute for Neutron Physics and Reactor Technology

International Nuclear Information System (INIS)

1990-03-01

The Institute for Neutron Physics and Reactor Technology treats research problems of nuclear engineering, mainly those that are related to the development of sodium-cooled fast breeder reactors and fusion reactor technology. The activities are in approximately equal parts of an experimental and theoretical nature. A great part of the research activities is performed in co-operation with other institutes and industrial groups in the framework of projects. For the Fast Breeder Reactor Project the Institute works on reactor physical design and safety problems by the core of large-scale fast breeder reactors. Questions concerning the consequences of accidents in light water reactors upon the environment and the population are treated as part of the Nuclear Safety Project. The Institute contributes to the Reprocessing Project with theoretical investigations on the physics of the fuel cycle and by developing control devices for a reprocessing plant. In the framework of the Fusion Project the Institute is concerned with neutron physical and technological questions of the breeder blanket. (orig.) [de

ZEDEX - A study of damage and disturbance from tunnel excavation by blasting and tunnel boring

International Nuclear Information System (INIS)

Emsley, S.; Olsson, Olle; Stenberg, L.; Alheid, H.J.; Falls, S.

1997-12-01

The objectives of the ZEDEX project were to understand the mechanical behaviour of the excavation disturbed zone (EDZ) with respect to its origin, character, magnitude of property change, extent and its dependence on excavation method. Excavation with normal smooth blasting, blasting with low shock explosives and tunnel boring were studied. The drifts are located at Aespoe at a depth of 420 m, the profiles are circular and 5 m in diameter. The results have shown that there is a damaged zone, close to the drift wall dominated by changes in rock properties which are irreversible, and that there is a disturbed zone beyond the damaged zone that is dominated by changes in stress state and mainly reversible. There is no distinct boundary between the two zones. The results from ZEDEX indicate that the role of the EDZ as a preferential pathway to radionuclide transport is limited to the damaged zone. The extent of the damaged zone can be limited through application of appropriate excavation methods. By limiting the extent of the damaged zone it should also be feasible to block pathways in the damaged zone by plugs placed at strategic locations

Endoscopic excavation for the treatment of small esophageal subepithelial tumors originating from the muscularis propria.

Science.gov (United States)

Ye, Li-ping; Zhu, Lin-hong; Zhou, Xian-bin; Mao, Xin-li; Zhang, Yu

2015-01-01

This study was designed to evaluate the safety and efficacy of endoscopic excavation for esophageal subepithelial tumors originating from the muscularis propria. Forty-five patients with esophageal subepithelial tumors originating from the muscularis propria were treated with endoscopic excavation between January 2010 and June 2012. The key steps were: (1) making several dots around the tumor; (2) incising the mucosa along with the marker dots, and then seperating the tumor from the muscularis propria by using a hook knife or an insulated-tip knife; (3) closing the artificial ulcer with clips after the tumor was removed. The mean tumor diameter was 1.1 ± 0.6 cm. Endoscopic excavation was successfully performed in 43 out of 45 cases (95.6%), the other 2 cases were ligated with nylon rope. During the procedure perforation occurred in 4 (8.9%) patients, who recovered after conservative treatment. No massive bleeding or delayed bleeding occurred. Histologic diagnosis was obtained from 43 (95.6%) patients. Pathological diagnoses of these tumors were leiomyomas (38/43) and gastrointestinal stromal tumors (5/43). Endoscopic excavation is a safe and effective method for the treatment of small esophageal subepithelial tumors originating from the muscularis propria.

ZEDEX - A study of damage and disturbance from tunnel excavation by blasting and tunnel boring

Energy Technology Data Exchange (ETDEWEB)

Emsley, S [Golder Associates, Maidenhead (United Kingdom); Olsson, Olle; Stenberg, L [Swedish Nuclear Fuel and Waste Co., Figeholm (Sweden); Alheid, H J [Federal Inst. for Geosciences and Natural Resources, Hannover (Germany); Falls, S [Queens Univ., Kingston, ON (Canada)

1997-12-01

The objectives of the ZEDEX project were to understand the mechanical behaviour of the excavation disturbed zone (EDZ) with respect to its origin, character, magnitude of property change, extent and its dependence on excavation method. Excavation with normal smooth blasting, blasting with low shock explosives and tunnel boring were studied. The drifts are located at Aespoe at a depth of 420 m, the profiles are circular and 5 m in diameter. The results have shown that there is a damaged zone, close to the drift wall dominated by changes in rock properties which are irreversible, and that there is a disturbed zone beyond the damaged zone that is dominated by changes in stress state and mainly reversible. There is no distinct boundary between the two zones. The results from ZEDEX indicate that the role of the EDZ as a preferential pathway to radionuclide transport is limited to the damaged zone. The extent of the damaged zone can be limited through application of appropriate excavation methods. By limiting the extent of the damaged zone it should also be feasible to block pathways in the damaged zone by plugs placed at strategic locations 68 refs, 92 figs, 31 tabs

Archaeological Excavation Report for Proposed Well 199-K-131 in Support of the 100-KR-4 Pump-and-Treat Project

Energy Technology Data Exchange (ETDEWEB)

Woody, Dave M.; Prendergast-Kennedy, Ellen L.

2004-06-22

An archaeological excavation was conducted at the site of proposed groundwater monitoring well 199-K-131 in support of the 100-KR-4 Pump-and-Treat Project between June 2 and 3, 2004. Excavations confirmed that there were no intact cultural deposits at the proposed well location. This report was prepared to document the findings of the test excavation.

Fate of excavated polluted soils, treated off site. Regulations and field enforcement status in various European countries. Synthesis

International Nuclear Information System (INIS)

Leroy, P.

2003-11-01

Most industrialized countries have to cope with problems of polluted soils that have their roots in past or present anthropic activities. The treatment and the management of contaminated soils is a fast-moving domain, both from a technological point of view and at the level of regulations. In this respect the future European 'soil directive' should reinforce legislations within the Members States, while harmonizing practices. The fate of excavated soils depends on multiple parameters. In some cases, materials are disposed of at landfills. In other cases, they are recovered and re-used according to specific modes. RE.CO.R.D. wishes to learn more about situations in various European countries, concerning the disposal as well as the re-use/recycling of excavated polluted soils treated off site. This study is in the continuation of the former study number 99-0506/1A performed by Adit in 1999 and 2000. This work reports on the state of legislations as well as their respective implementations in five European States (France, Belgium, The Netherlands, Italy and Germany). The aim of this analysis is to establish a comparative study of the regulations in force through selected countries

Appraising the Cost Efficiency of Higher Technological and Vocational Education Institutions in Taiwan Using the Metafrontier Cost-Function Model

Science.gov (United States)

Lu, Yung-Hsiang; Chen, Ku-Hsieh

2013-01-01

This paper aims at appraising the cost efficiency and technology of institutions of higher technological and vocational education. Differing from conventional literature, it considers the potential influence of inherent discrepancies in output quality and characteristics of school systems for institutes of technology (ITs) and universities of…

Excavation of the Surikamigawa dam diversion tunnel. Surikamigawa dam karihaisui tunnel kantsu

Energy Technology Data Exchange (ETDEWEB)

Ikeda, T.; Konno, T. (Ministry of Construction, Tokyo (Japan))

1994-04-01

A bypass tunnel construction has been completed at the Surikamigawa dam (Japan). This paper describes the summary of the construction. The full-swing dam construction work is scheduled to begin in 1995. The soils distributed near the dam site consist of lapillus tuff containing andesite-based light stones and tuff-based conglomerates containing large gravels. Excavation of the dam diversion tunnel has used a blasting method, and the tunnel construction has adopted an automatic tunnel cross section marking system and a non-electric explosion method. This marking system is a system to irradiate a laser beam onto the facing to depict excavation lines that realizes labor saving and high-accuracy excavation. The error at the tunnel completion was found 20 mm. The non-electric explosion method ignites a coated explosive layer with an impact wave, which is electrostatically safe, and reduces blasting vibration. Electric detonators have also been used because of using ANFO explosives. The result obtained from measurements of inner space displacement necessary for the blasting process has indicated that the area near the dam site consists of stable mountains. 6 figs., 4 tabs.

Predictive hydro-mechanical excavation simulation of a mine-by test at the Mont Terri rock laboratory

International Nuclear Information System (INIS)

Krug, St.; Shao, H.; Hesser, J.; Nowak, T.; Kunz, H.; Vietor, T.

2010-01-01

Document available in extended abstract form only. The Mont Terri rock laboratory was extended from mid October 2007 to end 2008 with the goal to allow the project partners to continue their cooperative research on the long term. The extension of the underground laboratory by the excavation of an additional 165 metres long access tunnel (Gallery 08) with four niches was taken as opportunity to conduct an instrumented mine-by test in one of the niches (Niche 2/Niche MB). The measurements during the bedding parallel excavation provided a large amount of data as a basis to understand the hydro-mechanical (HM) coupled behaviour of Opalinus Clay around the excavated niche. BGR was involved in the in-situ investigations (seismic measurements) as a member of the experiment team consisting of five organisations (incl. NAGRA, ANDRA, GRS, Obayashi). An important issue for BGR is the application of the numerical code RockFlow (RF) for HM coupled simulations in order to understand the behaviour of Opalinus Clay by the use of the gained measuring data for validation. Under the management of NAGRA a blind prediction was carried out for a group of modelers belonging to some of the experiment team organisations. After a first comparison between the numerical results of different HM coupled models during the prediction meeting of the teams in June 2009 the measurement data are provided by NAGRA in order to validate the numerical models. Basically the model predictions have already shown the correct tendencies and ranges of observed deformation and pore water pressure evolution besides some under- or overestimations. The future RF validation results after having done some slight parameter adjustments are intended to be presented in the paper. The excavation of Niche 2 was done from 13 October to 7 November 2008 with a constant excavation rate of 1.30 m per day. The orientation of the niche follows the bedding strike, which amounts 60 deg.. The bedding planes have an average dip of

Post-excavation analysis of a revised hydraulic model of the Room 209 fracture, URL, Manitoba, Canada

International Nuclear Information System (INIS)

Winberg, A.; Tin Chan; Griffiths, P.; Nakka, B.

1989-10-01

An excavation response test was conducted in the Room 209 on the 240 m level of the AECL Underground Research Laboratory. Model predictions prior to excavation were made of the geomechanical response of the rock mass and the hydraulic response of an intercepted fracture. The model results were compared with excavation response data collected in a comprehensive instrument array. The work performed has addressed discrepancies between calculated and in-situ measured hydraulic response as part of a post-test analysis. Already existing hydraulic conceptual models of the fracture were revised and any available information was included in the new model. The model reproduced the pre-excavation hydraulic head distribution and hydraulic test results in terms of normalized flow rate within 5% and 75%, respectively. It was also found that the model reproduced the results of cross-hole hydraulic interference tests at least from a qualitative standpoint. The next stage of the modelling addressed the response of the model to a simulation of the excavated pilot tunnel. The preliminary results suggested the presence of a skin of different permeability in a thin zone around the periphery of the tunnel. By altering the permeability in the floor and along the walls and roof of the periphery, a better correspondence between calculated and measured drawdown was obtained. The same also applied for measured groundwater inflow in quantity, though not for the actual distribution on inflow. As probable causes for the interpreted positive skin in the crown and wall, temporary partial unsaturation and propulsion of debris into the fracture were suggested. The negative skin in the floor was interpreted as an effect of the dense and high energy charges used in the excavation process. (authors)

PROSPECTS OF THE DEVELOPMENT OF THE MODERN EDUCATIONAL INSTITUTIONS' LEARNING AND RESEARCH ENVIRONMENT: TO THE 15TH ANNIVERSARY OF THE INSTITUTE OF INFORMATION TECHNOLOGIES AND LEARNING TOOLS OF NAPS OF UKRAINE

Directory of Open Access Journals (Sweden)

M. P. Shyshkina

2014-05-01

Full Text Available During 15 years the Institute of Information technology and training of NAPS of Ukraine carries out research work aimed at solving actual problems of the creation, implementation and use of ICT in education, construction and development of computer-based learning environment of open education and e-learning, electronic educational resources, managing and supporting of the researches, technologies of cloud computing. The article considers the main activities of the Institute of Information Technologies and Learning Tools of NAPS of Ukraine. The experience of actual pedagogical issues developing, cooperation among research institutions and universities within activities of joint research laboratories, are reflected. The prospective research directions that will contribute to the modernization and further development of modern learning and scientific environment of educational institutions of Ukraine, in particular, the introduction of cloud oriented tools and technologies, the learning e-resources quality assurance, are outlined. The aim of the paper is to outline the main activities of the Institute of Information technology and training of NAPS of Ukraine during last 15 years and reflect the experience and perspectives of scientific and pedagogical cooperation of national research institutions and universities.

Information technologies in carrying out monitoring comparisons of pedagogical higher education institutions

Directory of Open Access Journals (Sweden)

Вадим Валерьевич Гриншкун

2014-12-01

Full Text Available In article various approaches to use of information technologies when carrying out monitoring researches of higher educational institutions are described. Results of researches are considered on the example of indicators of pedagogical university.

The forecast of mining-induced seismicity and the consequent risk of damage to the excavation in the area of seismic event

Directory of Open Access Journals (Sweden)

Jan Drzewiecki

2017-01-01

Full Text Available The Central Mining Institute has developed a method for forecasting the amount of seismic energy created by tremors induced by mining operations. The results of geophysical measurements of S wave velocity anomalies in a rock mass or the results of analytic calculations of the values of pressure on the horizon of the elastic layers are used in the process of calculating the energy. The calculation program which has been developed and adopted has been modified over recent years and it now enables not only the prediction of the energy of dynamic phenomena induced by mining but also the forecasting of the devastating range of seismic shock. The results obtained from this calculation, usually presented in a more readable graphic form, are useful for the macroscopic evaluation of locations that are potential sources of seismic energy. Forecasting of the maximum energy of seismic shock without prior knowledge of the location of the shock's source, does not allow shock attenuation that results from, for example, a distance of tremor source from the excavation which will be affected by seismic energy, to be taken into consideration. The phenomena of energy dissipation, which is taken into account in the forecasts, create a new quality of assessment of threat to the excavation. The paper presents the principle of a method of forecasting the seismic energy of a shock and the risk of damage to the excavation as a result of the impact of its energy wave. The solution assumes that the source of the energy shock is a resilient layer in which the sum of the gravitational stresses, resulting from natural disturbances and those induced by the conducted or planned mining exploitation, is estimated. The proposed solution assumes a spherical model for the tremor source, for which seismic energy is forecasted as a function of the longwall advance and the elementary value of seismic energy destroying the excavation. Subsequently, the following are calculated for the

A Top Pilot Tunnel Preconditioning Method for the Prevention of Extremely Intense Rockbursts in Deep Tunnels Excavated by TBMs

Science.gov (United States)

Zhang, Chuanqing; Feng, Xiating; Zhou, Hui; Qiu, Shili; Wu, Wenping

2012-05-01

The headrace tunnels at the Jinping II Hydropower Station cross the Jinping Mountain with a maximum overburden depth of 2,525 m, where 80% of the strata along the tunnels consist of marble. A number of extremely intense rockbursts occurred during the excavation of the auxiliary tunnels and the drainage tunnel. In particular, a tunnel boring machine (TBM) was destroyed by an extremely intense rockburst in a 7.2-m-diameter drainage tunnel. Two of the four subsequent 12.4-m-diameter headrace tunnels will be excavated with larger size TBMs, where a high risk of extremely intense rockbursts exists. Herein, a top pilot tunnel preconditioning method is proposed to minimize this risk, in which a drilling and blasting method is first recommended for the top pilot tunnel excavation and support, and then the TBM excavation of the main tunnel is conducted. In order to evaluate the mechanical effectiveness of this method, numerical simulation analyses using the failure approaching index, energy release rate, and excess shear stress indices are carried out. Its construction feasibility is discussed as well. Moreover, a microseismic monitoring technique is used in the experimental tunnel section for the real-time monitoring of the microseismic activities of the rock mass in TBM excavation and for assessing the effect of the top pilot tunnel excavation in reducing the risk of rockbursts. This method is applied to two tunnel sections prone to extremely intense rockbursts and leads to a reduction in the risk of rockbursts in TBM excavation.

Logs of Paleoseismic Excavations Across the Central Range Fault, Trinidad

Science.gov (United States)

Crosby, Christopher J.; Prentice, Carol S.; Weber, John; Ragona, Daniel

2009-01-01

This publication makes available maps and trench logs associated with studies of the Central Range Fault, part of the South American-Caribbean plate boundary in Trinidad. Our studies were conducted in 2001 and 2002. We mapped geomorphic features indicative of active faulting along the right-lateral, Central Range Fault, part of the South American-Caribbean plate boundary in Trinidad. We excavated trenches at two sites, the Samlalsingh and Tabaquite sites. At the Samlalsingh site, sediments deposited after the most recent fault movement bury the fault, and the exact location of the fault was unknown until we exposed it in our excavations. At this site, we excavated a total of eleven trenches, six of which exposed the fault. The trenches exposed fluvial sediments deposited over a strath terrace developed on Miocene bedrock units. We cleaned the walls of the excavations, gridded the walls with either 1 m X 1 m or 1 m X 0.5 m nail and string grid, and logged the walls in detail at a scale of 1:20. Additionally, we described the different sedimentary units in the field, incorporating these descriptions into our trench logs. We mapped the locations of the trenches using a tape and compass. Our field logs were scanned, and unit contacts were traced in Adobe Illustrator. The final drafted logs of all the trenches are presented here, along with photographs showing important relations among faults and Holocene sedimentary deposits. Logs of south walls were reversed in Illustrator, so that all logs are drafted with the view direction to the north. We collected samples of various materials exposed in the trench walls, including charcoal samples for radiocarbon dating from both faulted and unfaulted deposits. The locations of all samples collected are shown on the logs. The ages of seventeen of the charcoal samples submitted for radiocarbon analysis at the University of Arizona Accelerator Mass Spectrometry Laboratory in Tucson, Ariz., are given in Table 1. Samples found in

Optimization design of foundation excavation for Xiluodu super-high arch dam in China

Directory of Open Access Journals (Sweden)

Qixiang Fan

2015-04-01

Full Text Available With better understanding of the quality and physico-mechanical properties of rocks of dam foundation, and the physico-mechanical properties and structure design of arch dam in association with the foundation excavation of Xiluodu arch dam, the excavation optimization design was proposed for the foundation surface on the basis of feasibility study. Common analysis and numerical analysis results demonstrated the feasibility of using the weakly weathered rocks III1 and III2 as the foundation surface of super-high arch dam. In view of changes in the geological conditions at the dam foundation along the riverbed direction, the design of extending foundation surface excavation area and using consolidating grouting and optimizing structure of dam bottom was introduced, allowing for harmonization of the arch dam and foundation. Three-dimensional (3D geomechanics model test and finite element analysis results indicated that the dam body and foundation have good overload stability and high bearing capacity. The monitoring data showed that the behaviors of dam and foundation correspond with the designed patterns in the construction period and the initial operation period.

Preliminary results of excavations at Lincoln Cave, Sterkfontein, South Africa

CSIR Research Space (South Africa)

Reynolds, SC

2003-05-01

Full Text Available , sandwiched between two flowstone layers which could be dated using uranium series methods. The excavation furthermore yielded good indications that a portion of an older breccia has been eroded and that fauna and artefacts from this older, reworked breccia...

Numerical Simulation of Blast Vibration and Crack Forming Effect of Rock-Anchored Beam Excavation in Deep Underground Caverns

Directory of Open Access Journals (Sweden)

XinPing Li

2017-01-01

Full Text Available Aiming at surrounding rock damage induced by dynamic disturbance from blasting excavation of rock-anchored beam in rock mass at moderate or far distance in underground cavern, numerical model of different linear charging density and crustal stress in underground cavern is established by adopting dynamic finite element software based on borehole layout, charging, and rock parameter of the actual situation of a certain hydropower station. Through comparison in vibration velocity, contour surface of rock mass excavation, and the crushing extent of excavated rock mass between calculation result and field monitoring, optimum linear charging density of blast hole is determined. Studies are also conducted on rock mass vibration in moderate or far distance to blasting source, the damage of surrounding rock in near-field to blasting source, and crushing degree of excavated rock mass under various in situ stress conditions. Results indicate that, within certain range of in situ stress, the blasting vibration is independent of in situ stress, while when in situ stress is increasing above certain value, the blasting vibration velocity will be increasing and the damage of surrounding rock and the crushing degree of excavated rock mass will be decreasing.

Design and construction of earth retaining walls with anchors employed in excavation works at Oi Nuclear Power Plant

International Nuclear Information System (INIS)

Saino, Susumu; Aoshima, Ken-ichiro; Kamide, Atsushi.

1990-01-01

In Oi Nuclear Power Station, Kansai Electric Power Co., Inc., No.3 and No.4 plants of each 1180 MWe output are additionally installed, neighboring existing No.1 and No.2 plants of each 1175 MWe output in operation. The start of operation is expected in December, 1991 in No.3 plant, and in February, 1993 in No.4 plant. The total quantity of earth excavated for this additional installation works is about 3.3 million m 3 . The main works are, subsequently to the preparation of the site, the excavation for the foundations of reactor buildings and others, and the construction of the foundations for the seawater system facilities for cooling condensers and reactor auxiliary machines, and the works were begun in May, 1987. The excavation by using anchors was carried out in seven places. The vertical excavation on large scale was carried out by using the earth retaining walls of concrete-sprayed anchor structure in drain pits. In this report, the outline of the geological features, the outline of the excavation works, the design of the earth retaining walls, the execution of concrete spraying, the planning and result of measurement are described. (K.I.)

Spacecraft computer technology at Southwest Research Institute

Science.gov (United States)

Shirley, D. J.

1993-01-01

Southwest Research Institute (SwRI) has developed and delivered spacecraft computers for a number of different near-Earth-orbit spacecraft including shuttle experiments and SDIO free-flyer experiments. We describe the evolution of the basic SwRI spacecraft computer design from those weighing in at 20 to 25 lb and using 20 to 30 W to newer models weighing less than 5 lb and using only about 5 W, yet delivering twice the processing throughput. Because of their reduced size, weight, and power, these newer designs are especially applicable to planetary instrument requirements. The basis of our design evolution has been the availability of more powerful processor chip sets and the development of higher density packaging technology, coupled with more aggressive design strategies in incorporating high-density FPGA technology and use of high-density memory chips. In addition to reductions in size, weight, and power, the newer designs also address the necessity of survival in the harsh radiation environment of space. Spurred by participation in such programs as MSTI, LACE, RME, Delta 181, Delta Star, and RADARSAT, our designs have evolved in response to program demands to be small, low-powered units, radiation tolerant enough to be suitable for both Earth-orbit microsats and for planetary instruments. Present designs already include MIL-STD-1750 and Multi-Chip Module (MCM) technology with near-term plans to include RISC processors and higher-density MCM's. Long term plans include development of whole-core processors on one or two MCM's.

Underground excavation methods for a high-level waste repository

International Nuclear Information System (INIS)

Peshel, J.; Gupta, D.; Nataraja, M.

1990-01-01

This paper reports on rock excavation methods for a High-Level Waste repository that should be selected to limit the potential for creating preferential pathways for groundwater to travel to the waste packages or for radionuclides to migrate to the accessible environment. The use of water and other foreign substances should be controlled so that the repository performance is not compromised. The excavated openings should remain stable so that operations can be carried out safely and the retrievability option maintained. As per the current conceptual designs presented by the Department of Energy, the exploratory shaft facility becomes a part of the repository if the Yucca Mountain site is found suitable for repository development. Therefore, the methods of constructing the underground openings should be compatible with the performance requirements for the repository. Also, the degree of damage to the rock surrounding the openings and the extent of the damage zone should not preclude adequate site characterization. The ESf construction and operation should be compatible with the site data gathering activities, such as geological, thermomechanical, hydrological and geochemical testing

Activities of the All-Union Institute for Heat Technology in suppression of nitrogen oxide emission by technological methods

Energy Technology Data Exchange (ETDEWEB)

Enyakin, Yu.P.; Kotler, V.R.; Babii, V.I.; Shtal' man, S.G.; Shcherbachenko, S.I. (Vsesoyuznyi Teplotekhnicheskii Institut (USSR))

1991-06-01

Evaluates research programs of the All-Union Institute for Heat Technology in the USSR from 1970 to 1991. Research and development programs, developed technologies or equipment types, their tests and use on a commercial scale are discussed. Power plants in the USSR which use the technologies are listed. The following technologies are comparatively evaluated: recirculation of flue gases to a combustion system (reduces emission of nitrogen oxides by about 2 times), two-stage coal combustion (reduces emission by 40-50%), three-stage combustion (reduces emission by 40-50%), use of special types of burners (reduces emission by 25-30%), adapting temperature of air supplied to the combustion zone (reduces emission by 20-30%). 10 refs.

Geohydromechanical Processes in the Excavation Damaged Zone in Crystalline Rock, Rock Salt, and Indurated and Plastic Clays

International Nuclear Information System (INIS)

Tsang, Chin-Fu; Bernier, Frederic; Davies, Christophe

2004-01-01

The creation of an excavation disturbed zone or excavation damaged zone is expected around all man-made openings in geologic formations. Macro- and micro-fracturing, and in general a redistribution of in situ stresses and rearrangement of rock structures, will occur in this zone, resulting in drastic changes of permeability to flow, mainly through the fractures and cracks induced by excavation. Such an EDZ may have significant implications for the operation and long-term performance of an underground nuclear waste repository. Various issues of concern need to be evaluated, such as processes creating fractures in the excavation damaged zone, the degree of permeability increase, and the potential for sealing or healing (with permeability reduction) in the zone. In recent years, efforts along these lines have been made for a potential repository in four rock types-crystalline rock, salt, indurated clay, and plastic clay-and these efforts have involved field, laboratory, and theoretical studies. The present work involves a synthesis of the ideas and issues that emerged from presentations and discussions on EDZ in these four rock types at a CLUSTER Conference and Workshop held in Luxembourg in November, 2003. First, definitions of excavation disturbed and excavation damaged zones are proposed. Then, an approach is suggested for the synthesis and intercomparison of geohydromechanical processes in the EDZ for the four rock types (crystalline rock, salt, indurated clay, and plastic clay). Comparison tables of relevant processes, associated factors, and modeling and testing techniques are developed. A discussion of the general state-of-the-art and outstanding issues are also presented. A substantial bibliography of relevant papers on the subject is supplied at the end of the paper

Developing the mechatronics and robotics at Nizhny Tagil Technological Institute of Ural Federal University

Science.gov (United States)

Goman, V. V.; Fedoreev, S. A.

2018-02-01

This report concerns the development trends of education in the field of the Mechatronics and Robotics at Nizhny Tagil Technological Institute (branch of Ural Federal University). The paper considers new teaching technologies, experience in upgrade of the laboratory facilities and some results of development Mechatronics and Robotics educational courses.

Comparative assessment of agricultural technology generating practices in universities and research institutes in north central zone of Nigeria

Directory of Open Access Journals (Sweden)

Gbolagade Benjamin Adesiji

2017-06-01

Full Text Available To understand the technology generating practices among universities and research institutes in north central zone of Nigeria, this study examined sources of funds for technology generating activities, compared agro-technology generating practices and identified constraining factors hindering technology generating practices. One hundred and fifty-two academic staff were randomly selected from universities and one hundred and thirty-six respondents were drawn from research institutes. Validated questionnaires with reliability coefficient of r = 0.92 were used to elicit data. Data were analyzed using descriptive statistics, Likert-scale, T-test and Factor analysis. Majority (93.4% of universities’ respondents used their personal funds to generate new technology compared to their counterparts in research institutes. The most widely employed mechanism for generating agricultural technologies was joint radio programmes (mean = 3.38 while the least was biotechnology (mean = 2.57. Major areas of differences in technology generation between the two institutions were the physical distance (t = 13.54; P < 0.05, farmers participation in field research trials (t = 8.50; P < 0.05, farmers co-finance of adaptive research trials (t = 3.77; P < 0.05 and adequate research facilities and incentives to workers (t = 2.05; P < 0.05. Factors constraining technology generation for universities were poor access to knowledge and information on new innovation (r = 0.815 while for research institutes it was limited physical resources (ICT, Telephone (r = 0.801. It was recommended therefore that respondents should look into options of writing alternate fund proposals and submitting to a wider range of funding bodies. Governance of innovation could be strengthened through the formation of a formal technological linkage advisory council.

Relic excavated in western India is probably of Georgian Queen Ketevan.

Science.gov (United States)

Rai, Niraj; Taher, Nizamuddin; Singh, Manvendra; Chaubey, Gyaneshwer; Jha, Aditya Nath; Singh, Lalji; Thangaraj, Kumarasamy

2014-01-01

History has well documented the execution of Queen Ketevan of Georgia by the Persian Emperor of modern day Iran. Based on historical records, in 1624 two Augustinian friars unearthed the queen's remains and one of them brought the relic to the St. Augustine convent in Goa, India. We carried out ancient DNA analysis on the human bone remains excavated from the St. Augustine convent by sequencing and genotyping of the mitochondrial DNA. The investigations of the remains revealed a unique mtDNA haplogroup U1b, which is absent in India, but present in Georgia and surrounding regions. Since our genetic analysis corroborates archaeological and literary evidence, it is likely that the excavated bone belongs to Queen Ketevan of Georgia. Copyright © 2013 Elsevier B.V. All rights reserved.

Development of digital photogrammetry for measurements of displacements in underground excavation

International Nuclear Information System (INIS)

Ohnishi, Yuzo; Ohtsu, Hiroyasu; Nishiyama, Satoshi; Ono, Tetsu; Matsui, Hiroya

2002-03-01

Because deformations are important indicators of the degree of stability during construction of rock structures, monitoring of deformation is a key element of construction of tunnels and structures for the underground research laboratory. Especially in the construction and maintenance of underground excavation, monitoring of deformations is needed for obtaining useful information to control its stability. We have been developing the application of digital photogrammetry to monitoring techniques in rock structures. Photogrammetric process has undergone a remarkable evolution with its transformation into digital photogrammetry. Photogrammetry has the advantage of measuring deformation of an object by some photos with easy measurements and excellent cost performance. In this paper, we present that the digital photogrammetry can monitor the displacements of the underground excavation accurately along with a capability of real-time measurement. (author)

Successful Implementation of Soil Segregation Technology at the Painesville FUSRAP Site - 12281

Energy Technology Data Exchange (ETDEWEB)

Buechi, Stephen P.; Andrews, Shawn M. [U.S. Army Corps of Engineers, Buffalo District, Buffalo, New York (United States); Lombardo, Andrew J. [Safety and Ecology Corporation, Beaver, Pennsylvania (United States); Lively, Jeffrey W. [AMEC Environment and Infrastructure, Grand Junction, Colorado (United States)

2012-07-01

Typically the highest cost component of the radiological soils remediation of Formerly Utilized Sites Remedial Action Program (FUSRAP) sites is the cost to transport and dispose of the excavated soils, typically contaminated with naturally occurring isotopes of uranium, thorium and radium, at an appropriately permitted off-site disposal facility. The heterogeneous nature of the contamination encountered at these sites makes it difficult to accurately delineate the extent of contaminated soil using the limited, discrete sampling data collected during the investigation phases; and difficult to precisely excavate only the contaminated soil that is above the established cleanup limits using standard in-field scanning and guiding methodologies. This usually results in a conservative guided excavation to ensure cleanup criteria are met, with the attendant transportation and disposal costs for the larger volumes of soil excavated. To address this issue during the remediation of the Painesville FUSRAP Site, located in Painesville, Ohio, the Buffalo District of the U.S. Army Corps of Engineers, and its contractor, Safety and Ecology Corporation (SEC), employed automatic soil segregation technology provided by MACTEC (now AMEC) to reduce the potential for transportation and disposal of soils that met the cleanup limits. This waste minimization technology utilized gamma spectroscopy of conveyor-fed soils to automatically segregate the material into above and below criteria discharge piles. Use of the soil segregation system resulted in cost savings through the significant reduction of the volume of excavated soil that required off-site transportation and disposal, and the reduction of the amount of imported clean backfill required via reuse of 'below criteria' segregated soil as place back material in restoring the excavations. Measurements taken by the soil segregation system, as well as results of quality control sampling of segregated soils, confirmed that soils

KBS-3H - Excavation of two horizontal drifts at the Aespoe Hard Rock Laboratory during year 2004-2005. Work description, summary of results and experience

International Nuclear Information System (INIS)

Baeckblom, Goeran; Lindgren, Erik

2005-10-01

SKB and Posiva Oy in Finland jointly study the possibility to develop a variant of the KBS-3 method for final disposal of spent nuclear fuel. The idea is to make serial deposition of canisters in long horizontal drifts instead of vertical deposition of single canisters in the deposition hole. The studies concerning the horizontal deposition alternative are conducted within the framework of a KBS-3H project, where certain demonstration activities are implemented. A key issue of the running project is to test the ability to excavate the horizontal deposition drifts. The objectives for this work are as follows: To show the feasibility of meeting the geometrical and other requirements; To construct two deposition drifts needed for the later project stages. One drift is needed to demonstrate that heavy load can be transported into the drift. One drift is needed to demonstrate that a plug (bulkhead) can be constructed by low-pH shotcrete; To evaluate the applicability of selected excavation methodologies for realistic repository conditions, and based on the experience in the project define need for technical developments/improvements. To meet the objectives, two deposition drifts were excavated at the Aespoe Hard Rock Laboratory during the period October 2004 to February 2005. One horizontal drift was 15 m in length and one 95 m in length. Both drifts were excavated to the diameter 1.85 m using horizontal push-reaming technology by adapting conventional raise-drilling equipment. The drifts were excavated in good rock conditions where no rock support or grouting was needed for feasible excavation or are needed to operate the drifts. SKB and Posiva have stringent geometrical requirements for the excavated drifts and the conclusions concerning compliance with the requirements are: Length: The project met this target. Two drifts were excavated, 15 m and 95 m respectively in accordance with the initial plan. Diameter: Actually it was not easy to measure the diameters of the

KBS-3H - Excavation of two horizontal drifts at the Aespoe Hard Rock Laboratory during year 2004-2005. Work description, summary of results and experience

Energy Technology Data Exchange (ETDEWEB)

Baeckblom, Goeran [Conrox AB, Stockholm (Sweden); Lindgren, Erik [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2005-10-15

SKB and Posiva Oy in Finland jointly study the possibility to develop a variant of the KBS-3 method for final disposal of spent nuclear fuel. The idea is to make serial deposition of canisters in long horizontal drifts instead of vertical deposition of single canisters in the deposition hole. The studies concerning the horizontal deposition alternative are conducted within the framework of a KBS-3H project, where certain demonstration activities are implemented. A key issue of the running project is to test the ability to excavate the horizontal deposition drifts. The objectives for this work are as follows: To show the feasibility of meeting the geometrical and other requirements; To construct two deposition drifts needed for the later project stages. One drift is needed to demonstrate that heavy load can be transported into the drift. One drift is needed to demonstrate that a plug (bulkhead) can be constructed by low-pH shotcrete; To evaluate the applicability of selected excavation methodologies for realistic repository conditions, and based on the experience in the project define need for technical developments/improvements. To meet the objectives, two deposition drifts were excavated at the Aespoe Hard Rock Laboratory during the period October 2004 to February 2005. One horizontal drift was 15 m in length and one 95 m in length. Both drifts were excavated to the diameter 1.85 m using horizontal push-reaming technology by adapting conventional raise-drilling equipment. The drifts were excavated in good rock conditions where no rock support or grouting was needed for feasible excavation or are needed to operate the drifts. SKB and Posiva have stringent geometrical requirements for the excavated drifts and the conclusions concerning compliance with the requirements are: Length: The project met this target. Two drifts were excavated, 15 m and 95 m respectively in accordance with the initial plan. Diameter: Actually it was not easy to measure the diameters of the

The Use of Interactive Learning Technology in Institutions of Higher Learning

Science.gov (United States)

Abykanova, Bakytgul; Nugumanova, Samal; Yelezhanova, Shynar; Kabylkhamit, Zhanargul; Sabirova, Zhanylsyn

2016-01-01

This paper is linked to a study aiming to provide a theoretical rationale for the methodological foundations of the use of interactive learning technology in institutions of higher learning and undertakes to describe the process of practical implementation of this approach and analyze the outcomes. The authors examine the views expressed by…

Factors Related to the Adoption of IT Emerging Technologies by Research and Non-Research Based Higher Education Institutions

Science.gov (United States)

Then, Keri Ann; Amaria, Pesi

2013-01-01

This study examined the adoption of information technology (IT) emerging technology by higher education institutions with a focus on non-research and research based institutions categorized by Carnegie Mellon classifications that are members of EDUCAUSE, a higher education non-profit organization, whose mission is the use of IT in higher…

Modelling of excavation depth and fractures in rock caused by tool indentation

International Nuclear Information System (INIS)

Kou Shaoquan; Tan Xiangchun; Lindqvist, P.A.

1997-10-01

The hydraulic regime after excavation in the near-field rock around deposition holes and deposition tunnels in a spent nuclear fuel repository is of concern for prediction of the saturation process of bentonite buffer and tunnel backfill. The hydraulic condition of main interest in this context is a result of the fracture network that is caused by the excavation. Modelling of the excavation disturbed zone in hard rocks caused by mechanical excavation has been carried out in the Division of Mining Engineering since 1993. This report contains an overview of the work conducted. The mechanical excavation is reasonably simplified as an indentation process of the interaction between rigid indenters and rocks. A large number of experiments have been carried out in the laboratory, and the results used for identifying crushed zones and fracture systems in rock under indentation are presented based on these experiments. The indentation causes crushing and damage of the rock and results in a crushed zone and a cracked zone. The indenter penetrates the rock with a certain depth when the force is over a threshold value relevant to the rock and tool. Outside the cracked zone there are basically three systems of cracks: median cracks, radial cracks, and side cracks. Fully developed radial cracks on each side of the indented area can connect with each other and join with median crack. This forms the so-called radial/median crack system. The influence of the mechanical properties of the rock is discussed based on our conceptual model, and the main factors governing the indentation event are summarised. The cracked zone is dealt with by an analytical fracture model. The side crack is simulated by applying the boundary element method coupled with fracture mechanics. Functional relationships are established relating either the indentation depth or the length of radial/median cracks to the various quantities characterising the physical event, namely the shape and the size of the

Modelling of excavation depth and fractures in rock caused by tool indentation

Energy Technology Data Exchange (ETDEWEB)

Kou Shaoquan; Tan Xiangchun; Lindqvist, P.A. [Luleaa Univ. of Technology (Sweden)

1997-10-01

The hydraulic regime after excavation in the near-field rock around deposition holes and deposition tunnels in a spent nuclear fuel repository is of concern for prediction of the saturation process of bentonite buffer and tunnel backfill. The hydraulic condition of main interest in this context is a result of the fracture network that is caused by the excavation. Modelling of the excavation disturbed zone in hard rocks caused by mechanical excavation has been carried out in the Division of Mining Engineering since 1993. This report contains an overview of the work conducted. The mechanical excavation is reasonably simplified as an indentation process of the interaction between rigid indenters and rocks. A large number of experiments have been carried out in the laboratory, and the results used for identifying crushed zones and fracture systems in rock under indentation are presented based on these experiments. The indentation causes crushing and damage of the rock and results in a crushed zone and a cracked zone. The indenter penetrates the rock with a certain depth when the force is over a threshold value relevant to the rock and tool. Outside the cracked zone there are basically three systems of cracks: median cracks, radial cracks, and side cracks. Fully developed radial cracks on each side of the indented area can connect with each other and join with median crack. This forms the so-called radial/median crack system. The influence of the mechanical properties of the rock is discussed based on our conceptual model, and the main factors governing the indentation event are summarised. The cracked zone is dealt with by an analytical fracture model. The side crack is simulated by applying the boundary element method coupled with fracture mechanics. Functional relationships are established relating either the indentation depth or the length of radial/median cracks to the various quantities characterising the physical event, namely the shape and the size of the

Magnetic fusion energy technology fellowship: Report on survey of institutional coordinators

International Nuclear Information System (INIS)

1993-02-01

In 1980, the Magnetic Fusion Energy Technology (MFET) Fellowship program was established by the US Department of Energy, Office of Fusion Energy, to encourage outstanding students interested in fusion energy technology to continue their education at a qualified graduate school. The basic objective of the MFET Fellowship program is to ensure an adequate supply of scientists in this field by supporting graduate study, training, and research in magnetic fusion energy technology. The program also supports the broader objective of advancing fusion toward the realization of commercially viable energy systems through the research by MFET fellows. The MFET Fellowship program is administered by the Science/Engineering Education Division of Oak Ridge Institute for Science and Education. Guidance for program administration is provided by an academic advisory committee

Evaluation of excavation experience: Pierre shale. Final report

International Nuclear Information System (INIS)

Abel, J.F. Jr.; Gentry, D.W.

1975-01-01

Pierre shale and its stratigraphic equivalents represent a potentially favorable geologic environment for underground storage of hazardous waste products. These rock formations cover great areal and vertical extents, and represent some of the least permeable rock formations within the continental United States. There are, however, several engineering problems associated with constructing underground openings in Pierre shale. This formation is relatively weak and tends to deteriorate rather rapidly if not protected from the mine environment. It will be necessary to place all underground openings below the surficially weathered upper 50 to 70 feet of Pierre shale which contains groundwater moving on fracture permeability. The optimum site for disposal of hazardous waste in Pierre shale, or its stratigraphic equivalents, would be a seismically stable platform bounded on all sides by faults. The optimum size of individual openings would be the minimum necessary for access, storage, and retrieval of waste components. Underground excavations in Pierre shale must be made with care, must be of limited dimensions, must be widely spaced, must be protected from prolonged contact with the mine environment, must be supported immediately after excavation, and must be sited to avoid areas of faulting and(or) intense jointing. Underground openings constructed with boring machines and supported with wet shotcrete are recommended

Parametric Optimization and Prediction Tool for Excavation and Prospecting Tasks, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Honeybee Robotics therefore proposed to develop a software tool for facilitating prospecting and excavation system trades in support of selecting an optimal...

CAD-based strength analysis of EK-18 excavator bucket construction for mounting of anti-adhesive devices

Science.gov (United States)

Zenkov, S. A.; Lobanov, D. V.

2018-03-01

3D rigid-body model of a bucket of power shovel EK-18 was built using modern CAD-software. Tetrahedral grid with 10-node second-order elements was chosen, and the given model was imported to APM WinMachine - model preparation preprocessor for finite element analysis. The finite element model was based on the geometrical model, imported from KOMPAS-3D to APM Studio. Calculation of stressed-strained state of the bucket was carried out under the forces emerging while digging with “back hoe” equipment. Shift, deformation and tension charts were planned and the most and the least strained areas were pointed out. Wet coherent soil excavation deals with soil adhesion to working bodies of power shovels and leads to reduced performance. The performance decrease is caused by a reduction of useful bucket capacity and partial unloading, increased front resistance to cutting (digging) caused by wet soil adhesion to a working body, increased bucket entry resistance, increased idle time caused by necessity to clean working bodies. Also energy losses increase and quality of work drops because friction forces go up. Friction force occurs while digging and levelling account for 30…70 percent of total digging resistance while performance decreases 1.2…2 times and more. Vibrothermal exposure creates new technological effect which involves a wider humidity range of efficient application and a reduction of friction forces. Disintegrating adhesion bonds with heating requires less driving force from the vibrator. Vibration boosts up heating of the contact layer, which reduces thermal energy losses. However, the question of piezoelectric ceramic actuators location on the excavator bucket needs to be dealt with. The most suitable spots for mounting piezoelectric ceramic devices for reducing soil adhesion to the excavator bucket were defined. Their efficiency is derived from combined (vibrothermal) methods of exposure. Such devices eliminates soil adhesion to the bucket and increases

A study of feasibility, design and cost of excavations for underground siting of nuclear power plants

International Nuclear Information System (INIS)

1976-02-01

A study conducted for the State Power Board on underground siting of nuclear power plants is presented. The report is divided into two chapters, both concerning the technical aspects of large underground openings. The first chapter gives a brief general survey of the problems involved, and the second outlines the technical aspects of a PWR project at a specific site. Details are given in 8 appendices and arrangement drawings. The project differs from conventional hydroelectric excavation schemes mainly in the fact that the spherical reactor containment requires a vault of 60m free span, and the turbine hall a cylindrical vault of 45m span, both of which exceed any span hitherto built for similar purposes. This requires a comparatively wide extrapolation of tested and available experience in underground excavations for permanent civil use. To what extent and under what circumstances such extrapolation is tenable must be tested in practice, preferably in a specially controlled prototype test. However the study indicates that conventional nuclear power plants can be sited underground when the topography and rock conditions are suitable. A 1000-2000 MW conventional plant adapted for underground siting will require large span caverns, tunnels and shafts, totalling about 1.0 mill. cubic metres of underground excavation. In addition access and cooling water tunnels, depending on the location, will require 0.2-0.5 mill. cubic metres of tunnel excavations. The excavations and support work can be completed within a construction time of about 2 1/2 years at an estimated total cost of 215 mill. Norwegian kroner (1975 value). (JIW)

Establishment of a Quantitative Medical Technology Evaluation System and Indicators within Medical Institutions.

Science.gov (United States)

Wu, Suo-Wei; Chen, Tong; Pan, Qi; Wei, Liang-Yu; Wang, Qin; Li, Chao; Song, Jing-Chen; Luo, Ji

2018-06-05

The development and application of medical technologies reflect the medical quality and clinical capacity of a hospital. It is also an effective approach in upgrading medical service and core competitiveness among medical institutions. This study aimed to build a quantitative medical technology evaluation system through questionnaire survey within medical institutions to perform an assessment to medical technologies more objectively and accurately, and promote the management of medical quality technologies and ensure the medical safety of various operations among the hospitals. A two-leveled quantitative medical technology evaluation system was built through a two-round questionnaire survey of chosen experts. The Delphi method was applied in identifying the structure of evaluation system and indicators. The judgment of the experts on the indicators was adopted in building the matrix so that the weight coefficient and maximum eigenvalue (λ max), consistency index (CI), and random consistency ratio (CR) could be obtained and collected. The results were verified through consistency tests, and the index weight coefficient of each indicator was conducted and calculated through analytical hierarchy process. Twenty-six experts of different medical fields were involved in the questionnaire survey, 25 of whom successfully responded to the two-round research. Altogether, 4 primary indicators (safety, effectiveness, innovativeness, and benefits), as well as 13 secondary indicators, were included in the evaluation system. The matrix is built to conduct the λ max, CI, and CR of each expert in the survey, and the index weight coefficients of primary indicators were 0.33, 0.28, 0.27, and 0.12, respectively, and the index weight coefficients of secondary indicators were conducted and calculated accordingly. As the two-round questionnaire survey of experts and statistical analysis were performed and credibility of the results was verified through consistency evaluation test, the

Endoscopic excavation for gastric heterotopic pancreas: an analysis of 42 cases from a tertiary center.

Science.gov (United States)

Zhang, Yu; Huang, Qin; Zhu, Lin-hong; Zhou, Xian-bin; Ye, Li-ping; Mao, Xin-li

2014-09-01

Because of the difficulty associated with making an accurate diagnosis of gastric heterotopic pancreas (HP) before surgery, surgical resection is usually performed in suspected cases. However, this is an invasive procedure and prone to certain surgical complications. This study was designed to evaluate the feasibility of endoscopic excavation for gastric HP, as well as the value of endoscopic ultrasonography (EUS) in diagnosing gastric HP. Between January 2007 and January 2013, 42 consecutive patients with gastric HP were enrolled in this retrospective study. Key steps: (1) Injection of a solution (100 ml saline + 2 ml indigo carmine + 1 ml epinephrine) into the submucosal layer after making several dots around the lesion; (2) Incision of the mucosa outside the marker dots with a needle-knife, and then circumferential excavation until complete resection of the lesion; (3) Closure of the artificial ulcer with several clips after tumor removal. In this study, 18 cases (42.9%) were suspected as gastric HP (assessed by two experienced endoscopists before endoscopic excavation), 8 (19.0%) were suspected as gastrointestinal stromal tumors, 7 (16.7%) as gastric polyp, and the remaining 9 cases (21.4%) were still unknown. The mean procedure duration was 28.6 min. En bloc resection by endoscopic excavation was achieved in 40 cases (95.2%), and no massive bleeding, delayed bleeding, perforation, or other severe complication occurred in these patients. Among the 42 lesions, a tube echo could be detected in 11 cases by EUS. Those 11 cases were diagnosed as gastric HP by histopathology. Endoscopic excavation appears to be a safe and feasible procedure for accurate histopathologic evaluation and curative treatment in gastric HP. Use of EUS has some value in the diagnosis of gastric HP before the procedure

Probabilistic analysis of soil : Diaphragm wall friction used for value engineering of deep excavation, north/south metro Amsterdam

NARCIS (Netherlands)

Buykx, S.M.; Delfgaauw, S.; Bosch, J.W.

2009-01-01

The excavation of deep building pits often requires a check against failure by uplift of low permeability ground layers below excavation level. Whenever the weight of these soil layers is less than the pore-water pressure underneath, measures to resist buoyancy are to be considered. The measures

Nuclear and Energy Research Institute (1956-2000). A case study under the science, technology and brazilian culture history

International Nuclear Information System (INIS)

Gordon, Ana Maria Pinho Leite

2003-01-01

We analysed a period of the contemporary Brazilian history with the aim to discuss the inter-relationship between science, technology (S and T) and culture in a developing country, showing as a background for a case of study the history of the 'Instituto de Pesquisas Energeticas e Nucleares'. The history of Science and Technology, as a result of the human brain ability of innovate using the resources offered by nature, it is not only the description of successive findings carried out by talented men. It is a reflex of determined age of history as a consequence of accumulated knowledge connected also to human and cultural relationships, which together leads to the scientific and technological progress. In fact, the human brain and society march along together and can not be separated in this journey. In our study we recovered the initial steps of IPEN's outbreak; inserted its achievements in the context of the national policy for nuclear technology and evaluated how this policy was a reply of the governmental organizations to the worldwide situation. Finally, we spread the scientific ideas and technological findings of this institution, who has translate much of the life style and culture of our society. For this purposes, we analysed internal technical report series elaborated by several researchers and few testimonies. The Institution developed the fuel cycle technology, supplied radioisotopes for medical diagnosis and treatment purposes, generating economic resources for our country. The nuclear techniques are a relevant tool for researchers of this Institution applied for several purposes, including the assessment of the radioactivity levels in the environment, radioprotection, etc. Besides those applications, other techniques including the laser technology, the fuel cell, corrosion studies, etc, were implemented as a result of the improved capabilities and skills acquired during the almost 50 years of the Institute's existence. We make evident two strong

Present situation of unused uranium fuel in Tokyo Institute of Technology

International Nuclear Information System (INIS)

Obara, T.; Ogawa, M.

2008-01-01

Present situation of unused enriched uranium fuel in Tokyo Institute of Technology is described. The fuels were for sub-critical experiments. There is no special facility for transportation in the site. But there is no technical problem for it. One of the important issues to be done is a duty by national regulation against nuclear disaster. (author)

Internacionalização dos Institutos de Pesquisas Tecnológicas Internationalization of the Technological Research Institutes

Directory of Open Access Journals (Sweden)

Fabiano Manfio

2012-04-01

Full Text Available O estudo da internacionalização das organizações emerge do processo de interação e troca entre organizações de diferentes países, em especial nas organizações comerciais e industriais. O foco deste estudo é a internacionalização dos Institutos de Pesquisas Tecnológicas - IPTs. Os estudos de caso foram realizados em três instituições: Instituto Brasileiro de Tecnologia do Couro, Calçado e Artefatos - IBTeC -, Instituto de Tecnologia para o Desenvolvimento - LACTEC e Instituto de Pesquisa Tecnológica do Estado de São Paulo - IPT®. A operacionalização da pesquisa ocorreu por meio de entrevistas semiestruturadas realizadas com diretores e pesquisadores, análise documental com material institucional de divulgação, relatórios de gestão, relatórios técnicos e outros documentos administrativos e observação direta por ocasião das visitas às instituições. As análises mostraram que as principais ações de internacionalização dos Institutos de Pesquisas Tecnológicas - IPTs -pesquisados ocorrem a partir das relações pessoais de seus pesquisadores. A internacionalização acontece principalmente em atividades de qualificação técnica, ficando as parcerias formais e a venda de serviços em segundo plano. Os resultados revelaram também uma grande diversidade de atividades internacionais desenvolvidas, contudo essas atividades caracterizam-se como de "baixa intensidade" quando comparadas com as atividades desenvolvidas pelos IPTs no país.The study of the internationalization of organizations emerges from the interaction and exchange process between organizations of different countries. However, until now the study of this process has focused on commercial and industrial organizations. With this in mind, this study had as a main objective the desire to research the activities of the internationalization of the technological research institutes. The research was carried out primarily through the use of qualitative

Technologies of polytechnic education in global benchmark higher education institutions

Science.gov (United States)

Kurushina, V. A.; Kurushina, E. V.; Zemenkova, M. Y.

2018-05-01

The Russian polytechnic education is going through the sequence of transformations started with introduction of bachelor and master degrees in the higher education instead of the previous “specialists”. The next stage of reformation in the Russian polytechnic education should imply the growth in quality of teaching and learning experience that is possible to achieve by accumulating the best education practices of the world-class universities using the benchmarking method. This paper gives an overview of some major distinctive features of the foreign benchmark higher education institution and the Russian university of polytechnic profile. The parameters that allowed the authors to select the foreign institution for comparison include the scope of educational profile, industrial specialization, connections with the leading regional corporations, size of the city and number of students. When considering the possibilities of using relevant higher education practices of the world level, the authors emphasize the importance of formation of a new mentality of an engineer, the role of computer technologies in engineering education, the provision of licensed software for the educational process which exceeds the level of a regional Russian university, and successful staff technologies (e.g., inviting “guest” lecturers or having 2-3 lecturers per course).

The material of the social: the mutual shaping of institutions by irrigation technology and society in Seguia Khrichfa, Morocco

NARCIS (Netherlands)

Kooij, van der S.; Zwarteveen, M.Z.; Kuper, M.

2015-01-01

In this paper we draw attention to the important role technology plays in co-mediating institutions, opening up some courses of action and closing off others. Irrigation studies generally recognize the importance of institutions in making technologies work, but tend to take the precise functioning

The material of the social: the mutual shaping of institutions by irrigation technology and society in Sequia Krichfa, Morocco

NARCIS (Netherlands)

van der Kooij, S.; Zwarteveen, M.; Kuper, M.

2015-01-01

In this paper we draw attention to the important role technology plays in co-mediating institutions, opening up some courses of action and closing off others. Irrigation studies generally recognize the importance of institutions in making technologies work, but tend to take the precise functioning

Reconstruction of measurable three-dimensional point cloud model based on large-scene archaeological excavation sites

Science.gov (United States)

Zhang, Chun-Sen; Zhang, Meng-Meng; Zhang, Wei-Xing

2017-01-01

This paper outlines a low-cost, user-friendly photogrammetric technique with nonmetric cameras to obtain excavation site digital sequence images, based on photogrammetry and computer vision. Digital camera calibration, automatic aerial triangulation, image feature extraction, image sequence matching, and dense digital differential rectification are used, combined with a certain number of global control points of the excavation site, to reconstruct the high precision of measured three-dimensional (3-D) models. Using the acrobatic figurines in the Qin Shi Huang mausoleum excavation as an example, our method solves the problems of little base-to-height ratio, high inclination, unstable altitudes, and significant ground elevation changes affecting image matching. Compared to 3-D laser scanning, the 3-D color point cloud obtained by this method can maintain the same visual result and has advantages of low project cost, simple data processing, and high accuracy. Structure-from-motion (SfM) is often used to reconstruct 3-D models of large scenes and has lower accuracy if it is a reconstructed 3-D model of a small scene at close range. Results indicate that this method quickly achieves 3-D reconstruction of large archaeological sites and produces heritage site distribution of orthophotos providing a scientific basis for accurate location of cultural relics, archaeological excavations, investigation, and site protection planning. This proposed method has a comprehensive application value.

UK Higher Education Institutions' Technology-Enhanced Learning Strategies from the Perspective of Disruptive Innovation

Science.gov (United States)

Flavin, Michael; Quintero, Valentina

2018-01-01

The publication of institutional strategies for learning, teaching and assessment in UK higher education is practically ubiquitous. Strategies for technology-enhanced learning are also widespread. This article examines 44 publicly available UK university strategies for technology-enhanced learning, aiming to assess the extent to which…

Perfect Power Prototype for Illinois Institute of Technology

Energy Technology Data Exchange (ETDEWEB)

Shahidehpour, Mohammad [Illinois Inst. Of Technology, Chicago, IL (United States)

2014-09-30

Starting in October 2008, Illinois Institute of Technology (IIT), in collaboration with over 20 participating members, led an extensive effort to develop, demonstrate, promote, and commercialize a microgrid system and offer supporting technologies that will achieve Perfect Power at the main campus of IIT. A Perfect Power system, as defined by the Galvin Electricity Initiative (GEI), is a system that cannot fail to meet the electric needs of the individual end-user. The Principle Investigator of this Perfect Power project was Dr. Mohammad Shahidehpour, Director of the Robert W. Galvin Center for Electricity Innovation at IIT. There were six overall objectives of the Perfect Power project: (1) Demonstrate the higher reliability introduced by the microgrid system at IIT; (2) Demonstrate the economics of microgrid operations; (3) Allow for a decrease of fifty percent (50%) of grid electricity load; (4) Create a permanent twenty percent (20%) decrease in peak load from 2007 level; (5) Defer planned substation through load reduction; (6) Offer a distribution system design that can be replicated in urban communities.

NASA's Solar System Exploration Research Virtual Institute: Science and Technology for Lunar Exploration

Science.gov (United States)

Schmidt, Greg; Bailey, Brad; Gibbs, Kristina

2015-01-01

The NASA Solar System Exploration Research Virtual Institute (SSERVI) is a virtual institute focused on research at the intersection of science and exploration, training the next generation of lunar scientists, and development and support of the international community. As part of its mission, SSERVI acts as a hub for opportunities that engage the larger scientific and exploration communities in order to form new interdisciplinary, research-focused collaborations. The nine domestic SSERVI teams that comprise the U.S. complement of the Institute engage with the international science and exploration communities through workshops, conferences, online seminars and classes, student exchange programs and internships. SSERVI represents a close collaboration between science, technology and exploration enabling a deeper, integrated understanding of the Moon and other airless bodies as human exploration moves beyond low Earth orbit. SSERVI centers on the scientific aspects of exploration as they pertain to the Moon, Near Earth Asteroids (NEAs) and the moons of Mars, with additional aspects of related technology development, including a major focus on human exploration-enabling efforts such as resolving Strategic Knowledge Gaps (SKGs). The Institute focuses on interdisciplinary, exploration-related science focused on airless bodies targeted as potential human destinations. Areas of study represent the broad spectrum of lunar, NEA, and Martian moon sciences encompassing investigations of the surface, interior, exosphere, and near-space environments as well as science uniquely enabled from these bodies. This research profile integrates investigations of plasma physics, geology/geochemistry, technology integration, solar system origins/evolution, regolith geotechnical properties, analogues, volatiles, ISRU and exploration potential of the target bodies. New opportunities for both domestic and international partnerships are continually generated through these research and

KBTAC [Knowledge-Based Technology Application Center] - The EPRI [Electric Power Research Institute]-sponsored knowledge-based technology application center

International Nuclear Information System (INIS)

Meyer, W.; Wood, R.M.; Scherer, J.

1990-01-01

The Electric Power Research Institute (EPRI) has announced the establishment of the Knowledge-Based Technology Application Center (KBTAC), whose goal is to assist member utilities with expert system technology and applications. The center, established November 7, 1989, is located on the campus of Syracuse University, Syracuse, New York, and will be operated jointly by Kaman Sciences Corporation and the university. The mission of the KBTAC is to assist EPRI member utilities to develop, test, and transfer expert systems into nuclear power plant operations, maintenance, and administration

3D Documentation of Archaeological Excavations Using Image-Based Point Cloud

Directory of Open Access Journals (Sweden)

Umut Ovalı

2017-03-01

Full Text Available Rapid progress in digital technology enables us to create three-dimensional models using digital images. Low cost, time efficiency and accurate results of this method put to question if this technique can be an alternative to conventional documentation techniques, which generally are 2D orthogonal drawings. Accurate and detailed 3D models of archaeological features have potential for many other purposes besides geometric documentation. This study presents a recent image-based three-dimensional registration technique employed in 2013 at one of the ancient city in Turkey, using “Structure from Motion” (SfM algorithms. A commercial software is applied to investigate whether this method can be used as an alternative to other techniques. Mesh model of the some section of the excavation section of the site were produced using point clouds were produced from the digital photographs. Accuracy assessment of the produced model was realized using the comparison of the directly measured coordinates of the ground control points with produced from model. Obtained results presented that the accuracy is around 1.3 cm.

IMPORTANCE OF COMPUTER TECHNOLOGY IN REALIZATION OF CULTURAL AND EDUCATIONAL TASKS OF PRESCHOOL INSTITUTIONS

Directory of Open Access Journals (Sweden)

Zvezdan Arsić

2016-06-01

Full Text Available The rapid scientific and technological development imposes numerous changes in all spheres of life and work. In such circumstances, a computer has become a part of all aspects of life: economy, education, free time, family. Since children in contemporary society increasingly acquire knowledge before the school age, the question is how to prepare them for the world in which we live, bearing in mind how significantly different it is from the world in which the previous generations grew up. The research was aimed at examining the attitudes of preschool teachers about the importance of computers in the realization of educational activities in preschool institutions. The study included 54 teachers from Kosovo and Metohija: Kosovska Mitrovica, Donja Gušterica and Ropotovo. The research results indicate that digital technology is a very important and a useful didactic tool in the realization of educational activities in preschool institutions and that preschool teachers have the required competence to implement the technology. However, they are not satisfied with the quality of their ICT education and training during their studies; they also feel that their institutions do not provide adequate working conditions for the use of computers in the realization of educational tasks.

The evolution of competitive settlement strategies in Fijian prehistory : results of excavations and radiometric dating

International Nuclear Information System (INIS)

Field, J.S.

2003-01-01

A series of excavations were completed between June 2001 and March 2002 in the Fiji Islands. The goal of this research was to investigate the evolution of competitive settlement strategies in Fijian prehistory from an archaeological and evolutionary ecological perspective. Twelve sites were excavated and mapped in the Sigatoka Valley, located in the southwestern corner of the main island of Viti Levu. Excavations were focused on determining the chronology of fortifications in the region, and the collected samples were compared to expectations based on GIS-based analyses of land productivity and historical documents pertaining to late-period warfare. Over four hundred archaeological sites have been identified in the Sigatoka Valley, and of these roughly one-third are purely defensive in configuration, with no immediate access to water or arable land. The Waikato Archaeological Dating Fund provided four radiometric dates for three defensive sites, and one site associated with a production area. (author). 6 refs., 1 fig

Our experience with the full-profile excavation of exploratory for tunnel pipes

Directory of Open Access Journals (Sweden)

Edita Lazarová

2006-12-01

Full Text Available The economic development of Slovakia places an emphasis on increasing the quality of transport infrastructure, which requires its modernization residing in building the transport network of international level and improving its efficiency and travel speed. The development of transport in Slovakia has been passing major changes related to the economic and political processes in the country. Regarding the geographical character of the land, the tunnel excavation is an inseparable feature of the road communications modernization. Approximately thirty kilometres of highway tunnels are planned for construction in Slovakia until 2020 and road tunnels should be constructed as well. The first modern highway tunnel Branisko, the longest one (4975 m in Slovakia was put into operation in 2003 with a preceding excavation of the Branisko exploratory gallery in the course of designed tunnel pipe. The tunnelling works on the exploratory gallery of Višňové tunnel started in January 1999 and finished in the late summer of 2002 due to unfavorable geological conditions. The excavation of a final profile of the Višňové tunnel is planned for 2007. The Horelica tunnel (605 m near Čadca was finished and put into operation in 2004. The tunnels Lučivná (250 m, Bôrik (999 m and Sitina (1440 m are in construction at present.

From Server to Desktop: Capital and Institutional Planning for Client/Server Technology.

Science.gov (United States)

Mullig, Richard M.; Frey, Keith W.

1994-01-01

Beginning with a request for an enhanced system for decision/strategic planning support, the University of Chicago's biological sciences division has developed a range of administrative client/server tools, instituted a capital replacement plan for desktop technology, and created a planning and staffing approach enabling rapid introduction of new…

An Institutional Framework to Explain the University-Industry Technology Transfer in a Public University of Mexico

Directory of Open Access Journals (Sweden)

Lizbeth Magdalena Puerta Sierra

2017-04-01

Full Text Available In the last years, studies and modifications to the science and technology regulatory framework in Mexico show the increase in the attention to transfer the research results of professors and researchers from higher education institutions, towards the productive sector with the purpose of generating regional, national and international growth and development. This study has conducted to the search of the factors that determine the increase of linkage activities and technology transfer. Based on the literature review, this study develops a framework integrated with the factors considered that have a significantly impact in the university-industry linkage and technology transfer. The proposed independent variables are the following: Institutional Factors, Academic Profile, and Innovation.

Excavations and chronology at the Redcliffs Flat site, Canterbury, New Zealand

International Nuclear Information System (INIS)

Jacomb, C.

2009-01-01

The Redcliffs Flat site is one of a number of early Maori archaeological sites that cluster near the mouth of the estuary of the Avon and Heathcote rivers. Although several have been the subject of archaeological investigations, the chronology and extent of the Redcliffs Flat site remain poorly understood. Recent excavations associated with the redevelopment of a suburban section allow some progress to be made on both fronts. A small excavation here yielded a surprising amount of faunal, lithic and stratigraphic information. The site is shown to have extended to close to the edge of the estuary at the time of occupation and a radiocarbon date on a fragment of moa eggshell confirms the fourteenth to early fifteenth century status of the site. The radiocarbon chronology of the sites of the wider Redcliffs area is reviewed in light of this result. (author). 41 refs., 6 figs., 3 tabs.

Apparatus and method for large tunnel excavation in soft and incompetent rock or ground

International Nuclear Information System (INIS)

Altseimer, J.H.; Hanold, R.J.

1975-01-01

A tunneling machine is described for producing large tunnels in soft rock or wet, clayey, unconsolidated or bouldery earth by simultaneously detaching the tunnel core by thermal melting a boundary kerf into the tunnel face and forming a supporting excavation wall liner by deflecting the molten materials against the excavation walls to provide, when solidified, a continuous wall supporting liner, and detaching the tunnel face circumscribed by the kerf with powered mechanical earth detachment means and in which the heat required for melting the kerf and liner material is provided by a compact nuclear reactor. (U.S.)

Plan for the testing of radiation measurement instrumentation intended for use at an excavation site

International Nuclear Information System (INIS)

Gehrke, R.J.

1994-11-01

This plan describes performance tests to be made with ionizing radiation measurement instrumentation designed and built for in-field assay at an excavation site. One instrument measures gross gamma-ray and neutron fields and the other identifies gamma-ray emitting radionuclides and also is capable of assaying for selected hazardous materials. These instruments will be operationally tested to verify that original specifications have been met and performance tested to establish and verify that they have the potential to function as intended at an excavation site

Progress Twining Program at Shibaura Institute of Technology

Science.gov (United States)

Komeda, Takashi

The Shibaura Institute of Technology (SIT) conducts two Twinning Programs. One is Malaysian Twinning Program, which is conducted in cooperation with 15 Japanese universities, and has SIT as its organizing member. The other is Hybrid Twinning Program, which is conducted with partner foreign universities, and is a graduate study program combining Masters and Doctoral programs. Two important reasons for conducting these twinning programs are to increase the number of foreign students studying in Japan and to promote friendly relations with various Asian countries. Twinning program is effective in enrolling students early and in lowering the cost of foreign study. Japanese students benefit too from good influence of interaction with students having a different culture and customs.

Investigation of the impact of excavation (reinforced) on the seismic ...

African Journals Online (AJOL)

Every year, as a result of earthquake, abundant losses may be created as result of roof motion and sliding and rupture. Under normal conditions, the ground and soils forming the ground tolerate and transfer the existing stresses and any kind of action like excavation and release of trench and applying dynamic load could ...

[Conceptual foundations of creation of branch database of technology and intellectual property rights owned by scientific institutions, organizations, higher medical educational institutions and enterprises of healthcare sphere of Ukraine].

Science.gov (United States)

Horban', A Ie

2013-09-01

The question of implementation of the state policy in the field of technology transfer in the medical branch to implement the law of Ukraine of 02.10.2012 No 5407-VI "On Amendments to the law of Ukraine" "On state regulation of activity in the field of technology transfers", namely to ensure the formation of branch database on technology and intellectual property rights owned by scientific institutions, organizations, higher medical education institutions and enterprises of healthcare sphere of Ukraine and established by budget are considered. Analysis of international and domestic experience in the processing of information about intellectual property rights and systems implementation support transfer of new technologies are made. The main conceptual principles of creation of this branch database of technology transfer and branch technology transfer network are defined.

The Impact of the Information and Communication Technologies (ICT) to the management of the higher education institutions

CERN Document Server

Ganev, P

1998-01-01

The paper is aiming to consider the benefits of the using of the newest ICT , that follow for the management of the higher education. The main theme of the forum is directed to the fact that the Higher Education Institutions should be open to innovation and should express a willing to learn. One of the most innovative area is the area of the Information and Communication Technologies. Almost every month is announced a new ICT that facilitates the effectiveness of the management and of the performed business and educational activities at all. That is why the Higher Education Institutions must be open to the innovation and in the field of ICT, because this technology requires special skills and every one that would like to profit from this technology must have a willing to learn. Definitely the higher education institutions should synchronize with the rhythm of the changing technologies, including ICT. They have to consider the changing of the market, they have to meet the business needs. It is obvious that tod...

Supplement analysis for paleontological excavation at the National Ignition Facility at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

1997-01-01

On December 15, 1997, contractor workers supporting the National Ignition Facility (NIF) construction uncovered bones suspected to be of paleontological importance. The NIF workers were excavating a utility trench near the southwest corner of the NIF footprint area, located at the northeast corner of the Lawrence Livermore National Laboratory (LLNL) Livermore Site, and were excavating at a depth of approximately 30 feet. Upon the discovery of bone fragments, the excavation in the immediate vicinity was halted and the LLNL archaeologist was notified. The archaeologist determined that there was no indication of cultural resources. Mark Goodwin, Senior Curator for the University of California Museum of Paleontology at the University of California, Berkeley, was then contacted. Mr. Goodwin visited the site on December 16th and confirmed that the bones consisted of a section of the skull, a portion of the mandible, several teeth, upper palate, and possibly the vertebrae of a mammoth, genus Mammuthus columbi. This supplement analysis evaluates the potential for adverse impacts of excavating skeletal remains, an activity that was only generally assessed by the NIF Project-Specific Analysis in the Final Programmatic Environmental impact Statement for Stockpile Stewardship and Management (SS and M PEIS) published in September 1996 (DOE/EIS-0236) and its Record of Decision published on December 19, 1996. This supplement analysis has been prepared pursuant to the DOE regulations implementing the National Environmental Policy Act (10 CFR 1021.314)

Sequential Subterranean Transport of Excavated Sand and Foraged Seeds in Nests of the Harvester Ant, Pogonomyrmex badius.

Directory of Open Access Journals (Sweden)

Walter R Tschinkel

Full Text Available During their approximately annual nest relocations, Florida harvester ants (Pogonomyrmex badius excavate large and architecturally-distinct subterranean nests. Aspects of this process were studied by planting a harvester ant colony in the field in a soil column composed of layers of 12 different colors of sand. Quantifying the colors of excavated sand dumped on the surface by the ants revealed the progress of nest deepening to 2 m and enlargement to 8 L in volume. Most of the excavation was completed within about 2 weeks, but the nest was doubled in volume after a winter lull. After 7 months, we excavated the nest and mapped its structure, revealing colored sand deposited in non-host colored layers, especially in the upper 30 to 40 cm of the nest. In all, about 2.5% of the excavated sediment was deposited below ground, a fact of importance to sediment dating by optically-stimulated luminescence (OSL. Upward transport of excavated sand is carried out in stages, probably by different groups of ants, through deposition, re-transport, incorporation into the nest walls and floors and remobilization from these. This results in considerable mixing of sand from different depths, as indicated in the multiple sand colors even within single sand pellets brought to the surface. Just as sand is transported upward by stages, incoming seeds are transported downward to seed chambers. Foragers collect seeds and deposit them only in the topmost nest chambers from which a separate group of workers rapidly transports them downward in increments detectable as a "wave" of seeds that eventually ends in the seed chambers, 20 to 80 cm below the surface. The upward and downward transport is an example of task-partitioning in a series-parallel organization of work carried out by a highly redundant work force in which each worker usually completes only part of a multi-step process.

Evolution of mud-capped dredge pits following excavation: sediment trapping and slope instability

Science.gov (United States)

Obelcz, J.; Xu, K.; Bentley, S. J.; Li, C.; Miner, M. D.; O'Connor, M. C.; Wang, J.

2016-02-01

Many fluvial channels incised the Northern Gulf of Mexico inner continental shelf during the late Quaternary. Mud-capped dredge pits (MCDPs), which are generally elongate and deep (8-10 m) excavations, target sandy fluvial channel deposits for coastal restoration projects. The morphological evolution of dredge excavations in noncohesive sandy substrate is well studied, but MCDPs have up to a several-meter-thick veneer of Holocene shelf mud overlying sandy channel deposits. This stratigraphy is hypothesized to result in more complex post-dredge morphology than pit walls simply slumping to the angle of repose shortly after excavation. Numerical modeling of MCDP post-dredge response conducted prior to excavation indicates pit walls may retrogressively fail, which is accounted for in pit design by assigning no-dredge setback buffers from pipelines or cultural and environmental resources. To validate model results and test effectiveness of setback buffers, a geophysical survey of the Sandy Point MCDP (20 km west of the Mississippi River Delta in 10m deep water), where 1.7 million m3 of sandy sediment was excavated in 2012, was conducted May 2015. A total of 84 line-km of high-resolution chirp subbottom and a 27 km2 grid of swath bathymetry and sidescan sonar were collected. The data indicate the dredge pit walls are differentially slumping, with the western pit wall in a more active state of failure than the eastern wall. The western failures morphologically resemble features observed along the muddy Mississippi River Delta Front at water depths of 20-100 m, including bowl-shaped collapse failures and retrogressive stair-stepped slumps; these failures may play a key role in evaluating the distance of setback buffer zone to pipelines. These features indicate the cohesive mud overlying the sandy infill has a prominent role in pit wall stability. A 0.5-1 m thick acoustically transparent package overlies the entire pit floor (interpreted as a possible fluid mud layer

Radioactive waste management in Centre for nuclear technologies and investigations, Institute VINCA

International Nuclear Information System (INIS)

Avramovic, I.

2007-01-01

Responsible radioactive waste management requires the implementation of measures that will afford protection of human health and the environment. Radioactive waste management system was improved in Center for Nuclear Technology and Research, Institute VINCA, during 2006 and 2007 regarding the activities of spent fuel removal and R-A research reactor decommissioning [sr

Aeronautical education and research at the Swiss Institute of Technology in Zurich

Science.gov (United States)

Karner, L; Ackeret, J

1931-01-01

Progress in the scientific and practical fields of aviation has caused the Swiss Institute of Technology to organize lectures and practical training courses in all three branches of aeronautics and to found centers of scientific research, laboratories, etc., in order to supply the government and industries with scientifically and technically trained engineers.

Management information system of research institute supported by ministry of science and technology

International Nuclear Information System (INIS)

1992-12-01

This book mentions development strategy of MIS. This book contains development strategy of MIS research institute supported by government, computerization of administrative work of research institute, library computer system, methodology on system development, LAN build of ministry science and technology, ocean data base energy data base, computerization of research data management case of construction and analysis for chemical DB, information system of life science, electronic data interchange, queueing theory, biotechnology and computer, comprehensive weather information system, special equipment of data and data processing of oil-hunt operation.

Management information system of research institute supported by ministry of science and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-12-15

This book mentions development strategy of MIS. This book contains development strategy of MIS research institute supported by government, computerization of administrative work of research institute, library computer system, methodology on system development, LAN build of ministry science and technology, ocean data base energy data base, computerization of research data management case of construction and analysis for chemical DB, information system of life science, electronic data interchange, queueing theory, biotechnology and computer, comprehensive weather information system, special equipment of data and data processing of oil-hunt operation.

Hydrogeologic characterization and evolution of the 'excavation damaged zone' by statistical analyses of pressure signals: application to galleries excavated at the clay-stone sites of Mont Terri (Ga98) and Tournemire (Ga03)

International Nuclear Information System (INIS)

Fatmi, H.; Ababou, R.; Matray, J.M.; Joly, C.

2010-01-01

Document available in extended abstract form only. This paper presents methods of statistical analysis and interpretation of hydrogeological signals in clayey formations, e.g., pore water pressure and atmospheric pressure. The purpose of these analyses is to characterize the hydraulic behaviour of this type of formation in the case of a deep repository of Mid- Level/High-Level and Long-lived radioactive wastes, and to study the evolution of the geologic formation and its EDZ (Excavation Damaged Zone) during the excavation of galleries. We focus on galleries Ga98 and Ga03 in the sites of Mont Terri (Jura, Switzerland) and Tournemire (France, Aveyron), through data collected in the BPP- 1 and PH2 boreholes, respectively. The Mont Terri site, crossing the Aalenian Opalinus clay-stone, is an underground laboratory managed by an international consortium, namely the Mont Terri project (Switzerland). The Tournemire site, crossing the Toarcian clay-stone, is an Underground Research facility managed by IRSN (France). We have analysed pore water and atmospheric pressure signals at these sites, sometimes in correlation with other data. The methods of analysis are based on the theory of stationary random signals (correlation functions, Fourier spectra, transfer functions, envelopes), and on multi-resolution wavelet analysis (adapted to nonstationary and evolutionary signals). These methods are also combined with filtering techniques, and they can be used for single signals as well as pairs of signals (cross-analyses). The objective of this work is to exploit pressure measurements in selected boreholes from the two compacted clay sites, in order to: - evaluate phenomena affecting the measurements (earth tides, barometric pressures..); - estimate hydraulic properties (specific storage..) of the clay-stones prior to excavation works and compare them with those estimated by pulse or slug tests on shorter time scales; - analyze the effects of drift excavation on pore pressures

The 2010-2011 excavation season at Al Zubarah, north-west Qatar

DEFF Research Database (Denmark)

Richter, Tobias; al-Naimi, Faisal; Yeomans, Lisa

2012-01-01

This paper briefly summarizes the results of the 2010–2011 archaeological fieldwork at the late eighteenth–twentieth-century abandoned city of al-Zubarah in north-west Qatar. The excavations in five areas inside the town, covering courtyard houses, a suq, a palatial compound, and a midden...

Excavation and aggregation as organizing factors in de novo construction by mound-building termites.

Science.gov (United States)

Green, Ben; Bardunias, Paul; Turner, J Scott; Nagpal, Radhika; Werfel, Justin

2017-06-14

Termites construct complex mounds that are orders of magnitude larger than any individual and fulfil a variety of functional roles. Yet the processes through which these mounds are built, and by which the insects organize their efforts, remain poorly understood. The traditional understanding focuses on stigmergy, a form of indirect communication in which actions that change the environment provide cues that influence future work. Termite construction has long been thought to be organized via a putative 'cement pheromone': a chemical added to deposited soil that stimulates further deposition in the same area, thus creating a positive feedback loop whereby coherent structures are built up. To investigate the detailed mechanisms and behaviours through which termites self-organize the early stages of mound construction, we tracked the motion and behaviour of major workers from two Macrotermes species in experimental arenas. Rather than a construction process focused on accumulation of depositions, as models based on cement pheromone would suggest, our results indicated that the primary organizing mechanisms were based on excavation. Digging activity was focused on a small number of excavation sites, which in turn provided templates for soil deposition. This behaviour was mediated by a mechanism of aggregation, with termites being more likely to join in the work at an excavation site as the number of termites presently working at that site increased. Statistical analyses showed that this aggregation mechanism was a response to active digging, distinct from and unrelated to putative chemical cues that stimulate deposition. Agent-based simulations quantitatively supported the interpretation that the early stage of de novo construction is primarily organized by excavation and aggregation activity rather than by stigmergic deposition. © 2017 The Author(s).

Excavating silences and tensions of agency|passivity in science education reform

Science.gov (United States)

Rivera Maulucci, Maria S.

2010-12-01

I reflect on studies by Rodriguez and Carlone, Haun-Frank, and Kimmel to emphasize the ways in which they excavate silences in the science education literature related to linguistic and cultural diversity and situating the problem of reform in teachers rather than contextual factors, such as traditional schooling discourses and forces that serve to marginalize science. I propose that the current push for top-down reform and accountability diminishes opportunities for receptivity, learning with and from students in order to transform teachers' practices and promote equity in science education. I discuss tensions of agency and passivity in science education reform and argue that attention to authentic caring constitutes another silence in the science education literature. I conclude that the current policy context positions teachers and science education researchers as tempered radicals struggling against opp(reg)ressive reforms and that there is a need for more studies to excavate these and other silences.

Endoscopic en bloc resection of an exophytic gastrointestinal stromal tumor with suction excavation technique

Science.gov (United States)

Choi, Hyuk Soon; Chun, Hoon Jai; Kim, Kyoung-Oh; Kim, Eun Sun; Keum, Bora; Jeen, Yoon-Tae; Lee, Hong Sik; Kim, Chang Duck

2016-01-01

Here, we report the first successful endoscopic resection of an exophytic gastrointestinal stromal tumor (GIST) using a novel perforation-free suction excavation technique. A 49-year-old woman presented for further management of a gastric subepithelial tumor on the lesser curvature of the lower body, originally detected via routine upper gastrointestinal endoscopy. Abdominal computed tomography and endoscopic ultrasound showed a 4-cm extraluminally protruding mass originating from the muscularis propria layer. The patient firmly refused surgical resection owing to potential cardiac problems, and informed consent was obtained for endoscopic removal. Careful dissection and suction of the tumor was repeated until successful extraction was achieved without serosal injury. We named this procedure the suction excavation technique. The tumor’s dimensions were 3.5 cm × 2.8 cm × 2.5 cm. The tumor was positive for C-KIT and CD34 by immunohistochemical staining. The mitotic count was 6/50 high-power fields. The patient was followed for 5 years without tumor recurrence. This case demonstrated the use of endoscopic resection of an exophytic GIST using the suction excavation technique as a potential therapy without surgical resection. PMID:27340363

Field observations and failure analysis of an excavation damaged zone in the Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Aoyagi, Kazuhei; Ishii, Eiichi; Ishida, Tsuyoshi

2017-01-01

In the construction of a deep underground facility, the hydromechanical properties of the rock mass around an underground opening are changed significantly due to stress redistribution. This zone is called an excavation damaged zone (EDZ). In high-level radioactive waste disposal, EDZs can provide a shortcut for the escape of radionuclides to the surface environment. Therefore, it is important to develop a method for predicting the detailed characteristics of EDZs. For prediction of the EDZ in the Horonobe Underground Research Laboratory of Japan, we conducted borehole televiewer surveys, rock core analyses, and repeated hydraulic conductivity measurements. We observed that niche excavation resulted in the formation of extension fractures within 0.2 to 1.0 m into the niche wall, i.e., the extent of the EDZ is within 0.2 to 1.0 m into the niche wall. These results are largely consistent with the results of a finite element analysis implemented with the failure criteria considering failure mode. The hydraulic conductivity in the EDZ was increased by 3 to 5 orders of magnitude compared with the outer zone. The hydraulic conductivity in and around the EDZ has not changed significantly in the two years following excavation of the niche. These results show that short-term unloading due to excavation of the niche created a highly permeable EDZ. (author)

Satellite tracking of radioactive shipments - High technology solution to tough institutional problems

International Nuclear Information System (INIS)

Harmon, L.H.; Grimm, P.D.

1987-01-01

Three troublesome institutional issues face every large-quantity radioactive materials shipment. They are routing, pre-notification, and emergency response. The Transportation Communications System (TRANSCOM), under development by DOE, is based on a rapidly developing technology to determine geographical location using geo-positioning satellite systems. This technology will be used to track unclassified radioactive materials shipments in real-time. It puts those charged with monitoring transportation status on top of very shipment. Besides its practical benefits in the areas of logistics planning and execution, it demonstrates emergency preparedness has indeed been considered and close monitoring is possible. This paper describes TRANSCOM in its technical detail and DOE plans and policy for its implementation. The state of satellite positioning technology and its business future is also discussed

Imagine Astronomy at the Rochester Institute of Technology

Science.gov (United States)

Rapson, Valerie; Almeyda, T.; Freeman, M.; Lena, D.; Principe, D.; Punzi, K.; Sargent, B. A.; Vaddi, S.; Vazquez, B.; Vorobiev, D.

2014-01-01

The Imagine RIT Innovation and Creativity Festival is an annual free event held each year on the campus of the Rochester Institute of Technology (RIT). The purpose of the festival is to showcase the work and research conducted by students and faculty at RIT, and get the public excited about science and technology. For the past three years, graduate students, post-docs and faculty in the Astrophysical Sciences and Technology graduate program at RIT have participated in the festival by showcasing their astronomy research in a fun, interactive and hands on way. We have presented work conducted with various telescopes in the fields of star formation and galaxy evolution. Here, we present our three unique exhibits and the public’s reception to each exhibit. We found that interactive games such as astro-trivia, and hands on activities such as building a scale model of the Hubble Space Telescope were the most exciting for visitors. Interactive pieces of the exhibit in general acquired the most attention, whereas posters and videos, despite their pictorial nature, were not as well received. The most successful piece of our exhibit each year has been solar observing through eclipse glasses and telescopes. Most people who observed the sun at our exhibit were left awe-struck because this was their first experience viewing an astronomical object through a telescope. We plan to improve upon our exhibit by introducing more hands-on activities that will engage the public in current astronomy research at RIT.

An integrated systems approach to remote retrieval of buried transuranic waste using a telerobotic transport vehicle, innovative end effector, and remote excavator

International Nuclear Information System (INIS)

Smith, A.M.; Rice, P.; Hyde, R.; Peterson, R.

1995-02-01

Between 1952 and 1970, over two million cubic feet of transuranic mixed waste was buried in shallow pits and trenches in the Subsurface Disposal Area at the Idaho National Engineering Laboratory Radioactive Waste Management Complex. Commingled with this two million cubic feet of waste is up to 10 million cubic feet of fill soil. The pits and trenches were constructed similarly to municipal landfills with both stacked and random dump waste forms such as barrels and boxes. The main contaminants are micron-sized particles of plutonium and americium oxides, chlorides, and hydroxides. Retrieval, treatment, and disposal is one of the options being considered for the waste. This report describes the results of a field demonstration conducted to evaluate technologies for excavating, and transporting buried transuranic wastes at the INEL, and other hazardous or radioactive waste sites throughout the US Department of Energy complex. The full-scale demonstration, conduced at RAHCO Internationals facilities in Spokane, Washington, in the summer of 1994, evaluated equipment performance and techniques for digging, dumping, and transporting buried waste. Three technologies were evaluated in the demonstration: an Innovative End Effector for dust free dumping, a Telerobotic Transport Vehicle to convey retrieved waste from the digface, and a Remote Operated Excavator to deploy the Innovative End Effector and perform waste retrieval operations. Data were gathered and analyzed to evaluate retrieval performance parameters such as retrieval rates, transportation rates, human factors, and the equipment's capability to control contamination spread

Summer Teacher Enhancement Institute for Science, Mathematics, and Technology Using the Problem-Based Learning Model

Science.gov (United States)

Petersen, Richard H.

1997-01-01

The objectives of the Institute were: (a) increase participants' content knowledge about aeronautics, science, mathematics, and technology, (b) model and promote the use of scientific inquiry through problem-based learning, (c) investigate the use of instructional technologies and their applications to curricula, and (d) encourage the dissemination of TEI experiences to colleagues, students, and parents.

Assessment of geomechanical properties, maximum depth and excavation damaged zone aspects - Expert report

International Nuclear Information System (INIS)

Amann, F.; Löw, S.; Perras, M.

2015-11-01

This comprehensive report published by the Swiss National Nuclear Safety Inspectorate ENSI discusses the expert report published on the need for the assessment of geomechanical properties and maximum depth of repositories for high, medium and low-activity nuclear wastes. Also, aspects concerning excavation damaged zones (EDZ) are considered. These are all criteria for the selection of sites as part of Phase 2 of the Swiss waste disposal project. Four questions are examined: are NAGRA’s documented basic considerations and calculations on Opalinus Clay comprehensive enough and correct, are the calculations on maximum depth correct, are the proposed storage perimeters correct with respect to depth and will NAGRA be able to take possible excavation damaged zones (EDZ) into account? Literature and references concerning the subject are quoted

Application of full-face round by the sequential blasting machine in tunnel excavation

Energy Technology Data Exchange (ETDEWEB)

Cho, Y.D.; Park, B.K.; Lee, S.E.; Lim, H.U.

1995-12-31

Many methods and techniques have been developed to reduce ground vibrations. Some of them are an adoption of electric millisecond detonators with a sequential blasting machine and an improvement of initiating system with an adequate number of delay intervals. To reduce the level of ground vibration in tunnel excavation, the sequential blasting machine (S.B.M.) with decisecond detonators was adopted. A total of 134 blasts was recorded at various sites and the results were analyzed. The distances blast-to-structures were ranged from 20.3 to 42.0 meter, where charge weights were varied from 0.25 to 0.75kg per delay. It is proved that the sequential blasting in tunnel excavation is very effective to control ground vibration.

National Science and Technology Institute for Translational Medicine (INCT-TM): advancing the field of translational medicine and mental health.

Science.gov (United States)

Hallak, Jaime E C; Crippa, José Alexandre S; Quevedo, João; Roesler, Rafael; Schröder, Nadja; Nardi, Antonio Egidio; Kapczinski, Flávio

2010-03-01

Translational medicine has been described as the integrated application of innovative pharmacology tools, biomarkers, clinical methods, clinical technologies and study designs to improve the understanding of medical disorders. In medicine, translational research offers an opportunity for applying the findings obtained from basic research to every-day clinical applications. The National Science and Technology Institute for Translational Medicine is comprised of six member institutions (Universidade Federal do Rio Grande do Sul, Universidade de São Paulo-Ribeirão Preto, Universidade Federal do Rio de Janeiro, Pontifícia Universidade Católica do Rio Grande do Sul, Universidade Estadual de Santa Catarina and a core facility that serves all centers). The objectives of the project are divided into four areas: Institutional, Research, Human Resources and Technology for the Community and Productive Sector. In this manuscript, we describe some of the approaches used to attain the main objectives of the National Science and Technology Institute for Translational Medicine, which include the development of 1) animal models for bipolar disorder; 2) strategies to investigate neurobehavioral function and cognitive dysfunction associated with brain disorders; 3) experimental models of brain function and behavior, neuropsychiatric disorders, cell proliferation, and cancer; 4) Simulated Public Speaking and 5) Virtual reality simulation for inducing panic disorder and agoraphobia. The main focus of the National Science and Technology Institute for Translational Medicine is the development of more useful methods that allow for a better application of basic research-based knowledge to the medical field.

Middle Stone Age stratigraphy and excavations at Die Kelders Cave 1 (Western Cape Province, South Africa): the 1992, 1993, and 1995 field seasons.

Science.gov (United States)

Marean, C W; Goldberg, P; Avery, G; Grine, F E; Klein, R G

2000-01-01

Die Kelders Cave 1, first excavated under the direction of Franz Schweitzer in 1969-1973, was re-excavated between 1992 and 1995 by a combined team from the South African Museum, SUNY at Stony Brook, and Stanford University. These renewed excavations enlarged the artefactual and faunal samples from the inadequately sampled and less intensively excavated lower Middle Stone Age (MSA) layers, increased our understanding of the complex site formation processes within the cave, enlarged the hominid sample from the MSA deposits, and generated ESR, TL, and OSL dates for the MSA layers. Importantly, these new excavations dramatically improved our comprehension of the vertical and lateral characteristics of the MSA stratigraphy. Surface plotting of the MSA layers has led to the identification of at least two major zones of subsidence that significantly warped the layers, draping some along the eroding surface contours of major blocks of fallen limestone roof rock. A third zone of subsidence is probably present in the older excavations. Dramatic roof falls of very large limestone blocks occurred at least twice-once in the middle of Layer 4/5 where the roof blocks were only slightly weathered after collapse, and at the top of Layer 6 where the blocks weathered heavily after collapse, producing a zone of decomposed rock around the blocks. Many of the sandy strata are cut by small and localized faults and slippages. All of the strata documented by Schweitzer's excavations are present throughout the exposed area to the west of his excavated area, where many of them thicken and become more complex. Layer 6, the thickest MSA layer, becomes less diagenetically altered and compressed to the west. Copyright 2000 Academic Press.

MBC model analysis for predicting the rock behavior in excavating the Mizunami Underground Research Laboratory

International Nuclear Information System (INIS)

Mori, Takayuki; Iwano, Keita; Nakajima, Makoto; Morikawa, Seiji; Tabei, Kazuto

2005-03-01

As a Phase 1 of MIU project (Mizunami Underground Research Laboratory project), through the laboratory and borehole in-situ tests, JNC Tono Geoscience Center plans to constitute the comprehensive geological model and predicts the rock behaviors in excavating the shaft and gallery. These model and results leads to be reflected by the next step research projects. So far, the Phase 1 of MIU project is coming to final stage, and the Phase 2 will start at next year in which the in-situ researches are planned through the excavation. In this study, the comprehensive geometrical model was drawn out through the Phase 1 data, and MBC model analysis was carried out to predict the rock mass behavior around the shaft and gallery. The following results are obtained. 1. With MIZ-1 borehole core, artificial joints, which are assumed to be produced by rock blasting, were formed through the Brazilian test. And through the rock shear test for these joints, these mechanical properties were obtained. 2. By examining the MIZ-1 borehole research data, Mizunami site was classified by mechanical and joint properties and the Geomechanical model were made up. 3. Through the MBC model, the shaft and gallery cases were analyzed which depend on the rock mass classification, Excavation Damaged Zone, and the direction of the galleries. These results showed that in most cases, the joint opening were little because of the rock stiffness, but by the existence of high inclined joints, the side wall of the galleries were damaged by the excavation. (author)

New policies for science and technology and the impacts on public research institutes: a case study in Brazil

Directory of Open Access Journals (Sweden)

Thales Haddad Novaes de Andrade

2013-08-01

Full Text Available This article aims to discuss how technological production has been affected by new organizational patterns of funding and evaluation, international transformations in terms of the reorganization of research centers, and changes in innovation practices. Researchers and scientists have had their activities redefined through new organizational formats that today are well-established. The purpose here is to verify the impacts that these tendencies have had on the scientific and technological production of Public Research Institutes. We analyzed the case of the Technological Research Institute (Instituto de Pesquisas Tecnológicas - IPT and found that from the 1990s onwards, research institutions in Brazil internalized organizational forms that enabled them to place themselves in the international agenda as reputational agents, and that the IPT internalized an international agenda, hiring new services and with new budgets. The institutions of scientific research tended to align their interests with hegemonic devices and to withdraw the participation of agents not able to make explicit the new formulas for recognition in the scientific field.

Rock samples from LEP/LHC tunnel excavation

CERN Multimedia

1985-01-01

Rock samples taken from 0 to 170 m below ground on the CERN site when the LEP (Large Electron Positron collider) pit number 6 was drilled in Bois-chatton (Versonnex). The challenges of LHC civil engineering: A mosaic of works, structures and workers of differents crafts and origins. Three consulting consortia for the engineering and the follow-up of the works. Four industrial consortia for doing the job. A young team of 25 CERN staff, 30 surface buildings, 32 caverns of all sizes, 170 000 m3 of concrete, 420 000 m3 excavated. 1998-2004 : six years of work and 340 millions Swiss Francs.

The Regional Research And Development Centre of the Asean Institute of Technology, Bangkok

OpenAIRE

anonymous anonymous

2017-01-01

The Asian Institure of Technology (AJT) is an autonomouse, International postgraduate Institute. It provides advanced education in engenering, science and allied fields through academic programme loading to Master's and Doctoral degree and Diplomat, and through research programmes are related  closely to the needs of Asia.

Hygienic evaluation of new technology for control of methane and dust in coal mines

Energy Technology Data Exchange (ETDEWEB)

Gadzhiev, G P; Deynega, V G; Sukhanov, V V; Levshina, I M; Yarym, N T; Petrenko, G A

1977-07-01

Exploitation of available new technology for mining is hindered by the dangers of gas evolution, and the need for maintenance of hygienic standards. The Moscow Mining Institute has developed, and proposed for industrial introduction, a new process for control of methane and dust in mine shafts; the method will help to raise significantly the productivity of excavating machines in high gas factor shafts. The process to combat methane and dust consists essentially in drilling boreholes from the side of the gallery, or from the outer surface, into the coal-bearing stratum. These boreholes are injected with a 24% solution of urea-formaldehyde resin (binder M/sub 2/), with 1% solution of ammonium chloride hardener. After several months this plastic is removed. The new technology involves the escape of toxic substances into the air, hence the need for hygienic testing. Additional study must estimate the danger of accidents, e.g., shaft fires, toxicity of combustion products of coal or binder. Study is also needed on pathologies which might occur to miners engaged in removal of the plastic with the new technology.

Methods to ensure the quality of excavated soil material from geogenically metalliferous sites

Science.gov (United States)

Liebhard, Peter; Sager, Manfred

2017-04-01

Soils at geogenically metalliferous sites might exceed heavy metal threshold levels with respect to agricultural use, apart from anthropogenic contamination sources. As a fundamental substrate for green plants and green plant production, soil is not easily renewable, its formation needs long time (e.g. 500 years for 20 mm). In Austria, about 10ha of soil get sealed every day, resulting in complete loss of its biological functions. Excavated soil material has been classified as waste from a legal point of view, which made 33 mill. tons resp. 48% of total waste in Austria in 2010. Recycling of excavated soil material for agricultural use will be an important task to reduce future waste and to enlarge agricultural substrate volumes, but methods to ensure proper qualities are needed to improve regulations. Within this investigation, the transfer of various metals from geogenically metalliferous soils to various crop plants will be investigated, and correlated with various simple soil test methods. Four excavated soil materials from the metalliferous schist zone within the Austrian province of Styria (Kraubath/Mur, Übelbach) and a low-metal reference sample have been taken as substrates to grow raygrass (lolium multiflorum) as a green cover, salad (Lactuca sativa) as a vegetable food item, oats (Avena sativa), maize (Zea mais) and stinging nettle (Urtica dioica) as a hyperaccumulating species. Results and recommendations will be presented.

Thermomechanical analysis of underground excavations in the vicinity of a nuclear waste isolation panel

International Nuclear Information System (INIS)

St John, C.M.

1987-06-01

This report summarizes the results of a series of analyses of excavations in the vicinity of waste emplacement panels. Specific consideration is given to the access drifts running between adjacent emplacement panels, the drift intersection at the entrance to the emplacement panels, and the waste emplacement excavations. Both horizontal and vertical emplacement models are considered, but greater emphasis is placed on the former. Three numerical modeling procedures were used in this study: a finite-element model was used for three-dimensional stress analysis of the tunnel intersection, a model based on the closed-form solution for point heat sources was used to predict temperatures and stresses in the vicinity of the emplacement panel, and simple two-dimensional boundary-element models were used to predict temperatures and stresses around excavations of various shapes. The results of two-dimensional stress analyses were postprocessed to determine the extent to which the strength of a rock mass, containing a set of vertical joints, was exceeded. The results presented in this report do not indicate that there will be any particular stability problems at the tunnel intersection investigated. Further, the effect of waste emplacement within the adjacent panels is to decrease the vertical rock stresses and increase the horizontal rock stresses at the intersection. These stress changes will tend to enhance the stability of larger-span excavations, including the tunnel intersection and the alcoves necessary for horizontal emplacement of waste canisters. The relatively high horizontal stresses experienced by the access were identified as a potential concern. However, evaluation of recent data on the thermomechanical properties of the rock mass modeled here has indicated that the stress changes will not be as severe as stated herein

Natural diet of coral-excavating sponges consists mainly of dissolved organic carbon (DOC).

Science.gov (United States)

Mueller, Benjamin; de Goeij, Jasper M; Vermeij, Mark J A; Mulders, Yannick; van der Ent, Esther; Ribes, Marta; van Duyl, Fleur C

2014-01-01

Coral-excavating sponges are the most important bioeroders on Caribbean reefs and increase in abundance throughout the region. This increase is commonly attributed to a concomitant increase in food availability due to eutrophication and pollution. We therefore investigated the uptake of organic matter by the two coral-excavating sponges Siphonodictyon sp. and Cliona delitrix and tested whether they are capable of consuming dissolved organic carbon (DOC) as part of their diet. A device for simultaneous sampling of water inhaled and exhaled by the sponges was used to directly measure the removal of DOC and bacteria in situ. During a single passage through their filtration system 14% and 13% respectively of the total organic carbon (TOC) in the inhaled water was removed by the sponges. 82% (Siphonodictyon sp.; mean ± SD; 13 ± 17 μmol L(-1)) and 76% (C. delitrix; 10 ± 12 μmol L(-1)) of the carbon removed was taken up in form of DOC, whereas the remainder was taken up in the form of particulate organic carbon (POC; bacteria and phytoplankton) despite high bacteria retention efficiency (72 ± 15% and 87 ± 10%). Siphonodictyon sp. and C. delitrix removed DOC at a rate of 461 ± 773 and 354 ± 562 μmol C h(-1) respectively. Bacteria removal was 1.8 ± 0.9 × 10(10) and 1.7 ± 0.6 × 10(10) cells h(-1), which equals a carbon uptake of 46.0 ± 21.2 and 42.5 ± 14.0 μmol C h(-1) respectively. Therefore, DOC represents 83 and 81% of the TOC taken up by Siphonodictyon sp. and C. delitrix per hour. These findings suggest that similar to various reef sponges coral-excavating sponges also mainly rely on DOC to meet their carbon demand. We hypothesize that excavating sponges may also benefit from an increasing production of more labile algal-derived DOC (as compared to coral-derived DOC) on reefs as a result of the ongoing coral-algal phase shift.

Natural diet of coral-excavating sponges consists mainly of dissolved organic carbon (DOC.

Directory of Open Access Journals (Sweden)

Benjamin Mueller

Full Text Available Coral-excavating sponges are the most important bioeroders on Caribbean reefs and increase in abundance throughout the region. This increase is commonly attributed to a concomitant increase in food availability due to eutrophication and pollution. We therefore investigated the uptake of organic matter by the two coral-excavating sponges Siphonodictyon sp. and Cliona delitrix and tested whether they are capable of consuming dissolved organic carbon (DOC as part of their diet. A device for simultaneous sampling of water inhaled and exhaled by the sponges was used to directly measure the removal of DOC and bacteria in situ. During a single passage through their filtration system 14% and 13% respectively of the total organic carbon (TOC in the inhaled water was removed by the sponges. 82% (Siphonodictyon sp.; mean ± SD; 13 ± 17 μmol L(-1 and 76% (C. delitrix; 10 ± 12 μmol L(-1 of the carbon removed was taken up in form of DOC, whereas the remainder was taken up in the form of particulate organic carbon (POC; bacteria and phytoplankton despite high bacteria retention efficiency (72 ± 15% and 87 ± 10%. Siphonodictyon sp. and C. delitrix removed DOC at a rate of 461 ± 773 and 354 ± 562 μmol C h(-1 respectively. Bacteria removal was 1.8 ± 0.9 × 10(10 and 1.7 ± 0.6 × 10(10 cells h(-1, which equals a carbon uptake of 46.0 ± 21.2 and 42.5 ± 14.0 μmol C h(-1 respectively. Therefore, DOC represents 83 and 81% of the TOC taken up by Siphonodictyon sp. and C. delitrix per hour. These findings suggest that similar to various reef sponges coral-excavating sponges also mainly rely on DOC to meet their carbon demand. We hypothesize that excavating sponges may also benefit from an increasing production of more labile algal-derived DOC (as compared to coral-derived DOC on reefs as a result of the ongoing coral-algal phase shift.

Re-Excavation of Seti First Tomb, Kv17, Luxor, Egypt

Directory of Open Access Journals (Sweden)

Ayman HAMED

2013-12-01

Full Text Available This article is discussing technical challenges within engineering works made during re-excavation of the 174 m long tunnel which was cut into bedrock of desert shale known as 'Esna shale'. Recent historical events, during the last decade, explained much of the tunnel deformations and dirt filling inside tunnel space "Debris", caused by multiple water runoff attack to king's valley. The author is also discussing the challenging work under severe financial regime; using non conventional solutions adopted with extraordinary actions in using junk yard equipment. Seti I tomb, is considered as the deepest opening in the valley, not mentioning the risk in re-excavation the tomb, harsh atmospheric conditions inside the tunnel, measured and monitored by author, needed a serious ventilation system to serve workers during removal of dirt. Through that, an interesting mathematical relation between atmospheric variables has been emphasized. Design of steel supporting system serving an inclined deep tunnel with irregular circumference, under strict condition of reversibility, has been performed as a remarkable topic, to solve and apply in such archaeological site. Finally, the article is considered as a scientific pattern for application of geo-engineering in conservation of underground archaeological sites.

Bringing robotics technology down to Earth

International Nuclear Information System (INIS)

Fuller, B.R.

1997-01-01

Robotics technology is successfully being transitioned from space to terrestrial applications. It is being modified and enhanced to help in the US DOE's Environmental Restoration and Waste Management Program. Some examples of these applications, ranging from large multijointed manipulators to autonomously navigated remote vehicles, are outlined in this article. They include the following: underground storage tank technology demonstration; light-duty utility arm system; remotely controlled material-handling system; remotely operated excavator; self-guided transfer vehicle. 10 figs

Coastal dune dynamics in response to excavated foredune notches

Science.gov (United States)

Ruessink, B. G.; Arens, S. M.; Kuipers, M.; Donker, J. J. A.

2018-04-01

Dune management along developed coasts has traditionally focussed on the suppression of the geomorphic dynamics of the foredune to improve its role in sea defence. Because a stabilized foredune acts as an almost total barrier to aeolian transport from the beach, the habitat diversity in the more landward dunes has degraded. With the overarching objective to mitigate this undesirable loss in biodiversity, dune management projects nowadays increasingly intend to restore aeolian dynamics by reconnecting the beach-dune system with notches excavated through the foredune. Here, we use repeat topographic survey data to examine the geomorphic response of a coastal dune system in the Dutch National Park Zuid-Kennemerland to five notches excavated in 2012-2013 within an 850-m stretch of the 20-m high established foredune. The notches were dug in a V-shape (viewed onshore), with a width between approximately 50 and 100 m at the top, a (cross-dune) length between 100 and 200 m, and excavation depths between 9 and 12.5 m. The 1 × 1 m digital terrain models, acquired with airborne Lidar and UAV photogrammetry, illustrate that during the 3-year survey period the notches developed into a U-shape because of wall deflation, and that up to 8-m thick and 150-m long depositional lobes formed landward of the notches. Sand budget computations showed that the sand volume of the entire study area increased by about 22,750 m3/year, which, given the 850-m width of the study area, corresponds to an aeolian input from the beach of approximately 26.5 m3/m/year. Between 2006 and 2012 all wind-blown beach sand deposited on the seaward side of the foredune; since 2013, the notches have caused 75% of the sand to be deposited landward of the foredune. This highlights that the notches are highly effective conduits for aeolian transport into the back dunes. Future monitoring is required to determine for how long the notches will stimulate aeolian dynamics and if (and when) vegetation eventually

Studying at the UCL Institute of Archaeology

Directory of Open Access Journals (Sweden)

Bill Sillar

2013-10-01

Full Text Available Ranked 1st in 'The Guardian' (2013 league table for studying archaeology Ranked 2nd in 'The Times' (2013 ‘Good University Guide’ 100% of Institute undergraduate finalists expressed satisfaction with our teaching and support in the UK National Student Surveys 2010 and 2011 Students at the UCL Institute of Archaeology discover the rich diversity of the human past, exploring societies from two million years ago to the present day, and asking questions of relevance to our shared global future. To address these questions students integrate the humanities and the sciences; using a wide range of approaches to collect, evaluate and interpret relevant evidence. At UCL and during survey and excavation projects students make life-long friends while developing teamwork, management and leadership skills. Studying archaeology demands energy and enthusiasm, it challenges expectations while developing the problem-solving and transferable skills which all employers are looking for. Graduates from the Institute go on to make wide-ranging contributions to society, including business, academia and archaeology.

Assessment of exposure to manganese in welding operations during the assembly of heavy excavation machinery accessories.

Science.gov (United States)

Smargiassi, A; Baldwin, M; Savard, S; Kennedy, G; Mergler, D; Zayed, J

2000-10-01

Welder exposure to metals in various industrial sectors is poorly characterized. We had the opportunity to carry out an exploratory study to characterize manganese exposure in welding operations in a recently established Quebec factory that assembled accessories for heavy excavation machinery. Ten workers were sampled for total manganese for at least two consecutive days out of three followed by two consecutive days for respirable manganese (with a size selective sampler with a median cut-off of 4 microns), during a typical week in the summer of 1998. Parts being welded were characterized as large or small. Small parts were those being welded on tables during subassembly. Workers were divided into two groups according to the parts they were welding. Seventy-eight percent of the total manganese exposure levels of welding operations during the assembly of large accessories of heavy excavation machinery exceeded the manganese American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 0.20 mg/m3 (GM 0.24 mg/m3, n = 14) while none exceeded the TLV during the assembly of small pieces (GM 0.06 mg/m3, n = 8). Welding operations during the assembly of large heavy excavation machinery accessories may pose a significant health hazard. Considering the importance of task-related variables affecting exposure among workers, further studies are needed to better characterize exposure determinants of welding operations during the assembly of heavy excavation machinery accessories.

Excavating Silences and Tensions of Agency|Passivity in Science Education Reform

Science.gov (United States)

Rivera Maulucci, Maria S.

2010-01-01

I reflect on studies by Rodriguez and Carlone, Haun-Frank, and Kimmel to emphasize the ways in which they excavate silences in the science education literature related to linguistic and cultural diversity and situating the problem of reform in teachers rather than contextual factors, such as traditional schooling discourses and forces that serve…

The Feasibility of a Continuous Learning Year Program at Fashion Institute of Technology.

Science.gov (United States)

Thomas, George Isaiah

This feasibility study provides the Fashion Institute of Technology with a number of continuous-learning-year calendar choices, along with several suggestions regarding implementation procedures. The nature of the implementation process and the issues confronting the college administrator who is willing to reschedule the college year to facilitate…

Integrating Social Sustainability in Engineering Education at the KTH Royal Institute of Technology

Science.gov (United States)

Björnberg, Karin Edvardsson; Skogh, Inga-Britt; Strömberg, Emma

2015-01-01

Purpose: The purpose of this paper is to investigate what are perceived to be the main challenges associated with the integration of social sustainability into engineering education at the KTH Royal Institute of Technology, Stockholm. Design/methodology/approach: Semi-structured interviews were conducted with programme leaders and teachers from…

Technology overview of mined repositories

International Nuclear Information System (INIS)

Gimera, R.; Thirumalai, K.

1982-01-01

Mined repositories present an environmentally viable option for permanent disposal of nuclear waste. This paper reviews the state-of-the-art mining technologies and identifies technological issues and developments necessary to mine a repository in basalt. The thermal loading, isolation, and retrieval requirements of a repository present unique technological challenges unknown to conventional mining practice. The technology issues and developments required in the areas of excavation, roof and ground support, equipment development, instrumentation development, and sealing are presented. Performance assessment methods must be developed to evaluate the adequacies of technologies developed to design, construct, operate, and decommission a repository. A stepwise test-and-development approach is used in the Basalt Waste Isolation Project to develop cost-effective technologies for a repository

Use of chemical explosives for emergency solar flare shelter construction and other excavations on the Martian surface

International Nuclear Information System (INIS)

Dick, R.D.; Blacic, J.D.; Pettitt, D.R.

1985-01-01

The necessity to shelter people on the Martian surface from solar flare particles at short notice and the need for long-term habitats with thick cosmic ray shielding suggests that explosives could be used effectively for excavation of such structures. Modern insensitive high explosives are safe, efficient, and reliable for rock breakage and excavation. Extensive Earth-bound experience leads us to propose several strategies for explosively-constructed shelters based on tunneling, cratering, and rock casting techniques

In Situ Remediation Integrated Program: Technology summary

International Nuclear Information System (INIS)

1994-02-01

The In Situ Remediation Integrated Program (ISR IP) was instituted out of recognition that in situ remediation could fulfill three important criteria: significant cost reduction of cleanup by eliminating or minimizing excavation, transportation, and disposal of wastes; reduced health impacts on workers and the public by minimizing exposure to wastes during excavation and processing; and remediation of inaccessible sites, including: deep subsurfaces, in, under, and around buildings. Buried waste, contaminated soils and groundwater, and containerized wastes are all candidates for in situ remediation. Contaminants include radioactive wastes, volatile and non-volatile organics, heavy metals, nitrates, and explosive materials. The ISR IP intends to facilitate development of in situ remediation technologies for hazardous, radioactive, and mixed wastes in soils, groundwater, and storage tanks. Near-term focus is on containment of the wastes, with treatment receiving greater effort in future years. ISR IP is an applied research and development program broadly addressing known DOE environmental restoration needs. Analysis of a sample of 334 representative sites by the Office of Environmental Restoration has shown how many sites are amenable to in situ remediation: containment--243 sites; manipulation--244 sites; bioremediation--154 sites; and physical/chemical methods--236 sites. This needs assessment is focused on near-term restoration problems (FY93--FY99). Many other remediations will be required in the next century. The major focus of the ISR EP is on the long term development of permanent solutions to these problems. Current needs for interim actions to protect human health and the environment are also being addressed

In Situ Remediation Integrated Program: Technology summary

Energy Technology Data Exchange (ETDEWEB)

1994-02-01

The In Situ Remediation Integrated Program (ISR IP) was instituted out of recognition that in situ remediation could fulfill three important criteria: significant cost reduction of cleanup by eliminating or minimizing excavation, transportation, and disposal of wastes; reduced health impacts on workers and the public by minimizing exposure to wastes during excavation and processing; and remediation of inaccessible sites, including: deep subsurfaces, in, under, and around buildings. Buried waste, contaminated soils and groundwater, and containerized wastes are all candidates for in situ remediation. Contaminants include radioactive wastes, volatile and non-volatile organics, heavy metals, nitrates, and explosive materials. The ISR IP intends to facilitate development of in situ remediation technologies for hazardous, radioactive, and mixed wastes in soils, groundwater, and storage tanks. Near-term focus is on containment of the wastes, with treatment receiving greater effort in future years. ISR IP is an applied research and development program broadly addressing known DOE environmental restoration needs. Analysis of a sample of 334 representative sites by the Office of Environmental Restoration has shown how many sites are amenable to in situ remediation: containment--243 sites; manipulation--244 sites; bioremediation--154 sites; and physical/chemical methods--236 sites. This needs assessment is focused on near-term restoration problems (FY93--FY99). Many other remediations will be required in the next century. The major focus of the ISR EP is on the long term development of permanent solutions to these problems. Current needs for interim actions to protect human health and the environment are also being addressed.

In situ measurements of rock salt permeability changes due to nearby excavation

International Nuclear Information System (INIS)

Stormont, J.C.; Howard, C.L.; Daemen, J.J.K.

1991-07-01

The Small-Scale Mine-By was an in situ experiment to measure changes in brine and gas permeability of rock salt as a result of nearby excavation. A series of small-volume pressurized brine- and gas-filled test intervals were established 8 m beneath the floor of Room L1 in the WIPP underground. The test intervals were isolated in the bottom of the 4.8-cm diameter monitoring boreholes with inflatable rubber packers, and are initially pressurized to about 2 MPa. Both brine- and gas-filled test intervals were located 1.25, 1.5, 2, 3, and 4 r from the center of a planned large-diameter hole, where r is the radius of the large-diameter hole. Prior to the drilling of the large-diameter borehole, the responses of both the brine- and gas-filled test intervals were consistent with the formation modeled as a very low permeability, low porosity porous medium with a significant pore (brine) pressure and no measurable gas permeability. The drilling of the mine-by borehole created a zone of dilated, partially saturated rock out to about 1.5 r. The formation pressure increases from near zero at 1.5 r to the pre-excavation value at 4 r. Injection tests reveal a gradient of brine permeabilities from 5 x 10 -18 m 2 at 1.25 r to about the pre-excavation value (10 -21 m 2 ) by 3 r. Gas-injection tests reveal measurable gas permeability is limited to within 1.5 r. 17 refs., 24 figs., 6 tabs

Quality Assurance Issues in Conducting Multi-Institutional Advanced Technology Clinical Trials

International Nuclear Information System (INIS)

Purdy, James A.

2008-01-01

The National Cancer Institute-sponsored Advanced Technology Quality Assurance (QA) Consortium, which consisted of the Image-Guided Therapy QA Center, Radiation Therapy Oncology Group, Radiological Physics Center, Quality Assurance Review Center, and Resource Center for Emerging Technologies, has pioneered the development of an infrastructure and QA method for advanced technology clinical trials that requires volumetric digital data submission of a protocol patient's treatment plan and verification data. In particular, the Image-Guided Therapy QA Center has nearly 15 years experience in facilitating QA review for Radiation Therapy Oncology Group advanced technology clinical trials. This QA process includes (1) a data integrity review for completeness of protocol required elements, the format of data, and possible data corruption, and recalculation of dose-volume histograms; (2) a review of compliance with target volume and organ-at-risk contours by study chairs; and (3) a review of dose prescription and dose heterogeneity compliance by the Radiation Therapy Oncology Group Headquarters Dosimetry Group or the Radiological Physics Center dosimetrists (for brachytherapy protocols). This report reviews the lessons learned and the QA challenges presented by the use of advanced treatment modalities in clinical trials requiring volumetric digital data submission

Single-charge craters excavated during subsurface high-explosive experiments at Big Black Test Site, Mississippi

International Nuclear Information System (INIS)

Woodruff, W.R.; Bryan, J.B.

1978-01-01

Single-charge and row-charge subsurface cratering experiments were performed to learn how close-spacing enhances single-crater dimensions. Our first experimental phase established cratering curves for 60-lb charges of the chemical explosive. For the second phase, to be described in a subsequent report, the Row-cratering experiments were designed and executed. This data report contains excavated dimensions and auxiliary data for the single-charge cratering experiments. The dimensions for the row-charge experiments will be in the other report. Significant changes in the soil's water content appeared to cause a variability in the excavated dimensions. This variability clouded the interpretation and application of the cratering curves obtained

Motivational Factors of Companies that Establish Cooperation with Institutes of Science and Technology

Directory of Open Access Journals (Sweden)

Bruno Giovanni Mazzola

2016-04-01

Full Text Available Technological innovation is deemed strategic for organizations and nations to achieve and sustain competitive advantage. One of the most effective means for companies to achieve these innovations is through the relationship with universities. Thus, this study aimed to identify the main factors that motivate companies to establish this partnership. Hence, a descriptive study was elaborated, in which respondents are companies that have some level of cooperation with universities and institutes of science and technology. The results obtained show that the main reasons are, according to their importance: (1 to strengthen the technology, (2 to search for new sources of creativity, (3 to obtain expertise in market-oriented technologies, (4 to acquire new technologies; (5 to reach skilled labor, (6 to train their human resources, and (7 to develop new products. Furthermore, this study found that the less important factors are related to social reasons; this finding deserves further investigation in future studies.

Self-healing of excavation-disturbed rocks in the near field of underground cavities - exemplary measurements in rock salt and interpretation of preliminary results

International Nuclear Information System (INIS)

Wieczorek, K.; Schwarzianeck, P.; Rothfuchs, T.

2001-01-01

Excavation disturbed zones develop in all kinds of rock as a consequence of the opening of cavities. Such zones are characterized by a change in hydraulic behaviour which can form a problem with regard to the sealing of waste disposal areas. Rocks showing a plastic behaviour, like rock salt, have the potential of healing when the stress state which was disturbed by excavation returns to an advantageous state. If healing can reliably be predicted, the excavation disturbed zone may not form a long-term safety issue in rock salt. Investigations of permeability and stress state around lined and open excavations have been performed in order to relate hydraulic behaviour to stress state. First results which are presented here are promising. (authors)

Excavations at the Buller River Site (K29/8), January 2004

International Nuclear Information System (INIS)

Jacomb, C.; Tucker, B.; Walter, R.

2004-01-01

The Buller River Site (K29/8) is located on the south (true left) bank of the Buller, or Kawatiri, River directly across from Westport and approximately one kilometre from the present shoreline. This report describes the excavations at Buller River in February 2004, outlines the results to date and canvasses options for future research. 12 refs., 11 figs

Remediating Contaminant Plumes in Groundwater with Shallow Excavations Containing Coarse Reactive Media.

Science.gov (United States)

Hudak, Paul F

2018-02-01

A groundwater flow and mass transport model tested the capability of shallow excavations filled with coarse, reactive media to remediate a hypothetical unconfined aquifer with a maximum saturated thickness of 5 m. Modeled as contaminant sinks, the rectangular excavations were 10 m downgradient of an initial contaminant plume originating from a source at the top of the aquifer. The initial plume was approximately 259 m long, 23 m wide, and 5 m thick, with a downgradient tip located approximately 100 m upgradient of the site boundary. The smallest trench capable of preventing offsite migration was 11 m long (measured perpendicular to groundwater flow), 4 m wide (measured parallel to groundwater flow), and 3 m deep. Results of this study suggest that shallow trenches filled with coarse filter media that partially penetrate unconfined aquifers may be a viable alternative for remediating contaminated groundwater at some sites.

Institutional Means for Ensuring the Technological Leadership of Germany in the EU Economic System

Directory of Open Access Journals (Sweden)

Dovgal Olеna A.

2017-09-01

Full Text Available The article focuses on the analysis of institutional means for ensuring the technological leadership of Germany in the economic system of the EU. The main idea of all the programs and strategies of the European Union is to ensure competitive and dynamic development. Germany occupies a leading position in many respects both in the European and global technology market, which is due to the country’s strong scientific potential and the high level of spending on R&D. The article compares the tasks of the national high-tech strategy of the FRG and the strategy of the EU Innovation Union. There generalized the functions of the main components of the system of scientific associations of the Federal Republic of Germany, which are an effective tool for implementing the state policy in the field of innovation investment. An approach to qualitative assessment of the level of information interaction of the subjects in the system of R&D institutes and the diffusion of technologies using the criterion of information communication is proposed. A prospect for further research on this issue is a comprehensive analysis of the main components of Germany’s innovation strategy in the EU economic system.

Crown Prince Regent's Resolution extending the authority of the Institute for Energy Technology regarding Kjeller and Halden

International Nuclear Information System (INIS)

1990-01-01

This Resolution extends the authority of the Institute for Energy Technology (IFE) to own and operate nuclear reactors to 31 December 1999. The Institute owns and operates the JEEP II research reactor and the Halden Boiling Water Reactor, a research reactor established as an OECD-sponsored international project. (NEA) [fr

Microseism Induced by Transient Release of In Situ Stress During Deep Rock Mass Excavation by Blasting

Science.gov (United States)

Yang, Jianhua; Lu, Wenbo; Chen, Ming; Yan, Peng; Zhou, Chuangbing

2013-07-01

During deep rock mass excavation with the method of drill and blast, accompanying the secession of rock fragments and the formation of a new free surface, in situ stress on this boundary is suddenly released within several milliseconds, which is termed the transient release of in situ stress. In this process, enormous strain energy around the excavation face is instantly released in the form of kinetic energy and it inevitably induces microseismic events in surrounding rock masses. Thus, blasting excavation-induced microseismic vibrations in high-stress rock masses are attributed to the combined action of explosion and the transient release of in situ stress. The intensity of stress release-induced microseisms, which depends mainly on the magnitude of the in situ stress and the dimension of the excavation face, is comparable to that of explosion-induced vibrations. With the methods of time-energy density analysis, amplitude spectrum analysis, and finite impulse response (FIR) digital filter, microseismic vibrations induced by the transient release of in situ stress were identified and separated from recorded microseismic signals during a blast of deep rock masses in the Pubugou Hydropower Station. The results show that the low-frequency component in the microseismic records results mainly from the transient release of in situ stress, while the high-frequency component originates primarily from explosion. In addition, a numerical simulation was conducted to demonstrate the occurrence of microseismic events by the transient release of in situ stress, and the results seem to have confirmed fairly well the separated vibrations from microseismic records.

Special course for global nuclear human resource development in cooperation with Hitachi-GE nuclear energy in Tokyo institute of technology

International Nuclear Information System (INIS)

Ujita, H.; Futami, T.; Saito, M.; Murata, F.; Shimizu, M.

2012-01-01

Many Asian countries are willing to learn Japanese nuclear power plants experiences, and are interested in introducing nuclear power generation to meet their future energy demand. Special course for Global Nuclear Human Resource Development was established in April, 2011 in the Department of Nuclear Engineering at Graduate School of Tokyo Institute of Technology in cooperation with Hitachi-GE Nuclear Energy. Purpose of the special course is to develop global nuclear engineers and researchers not only in the Tokyo Institute of Technology but also in the educational institutes of Southeast Asian countries

Development of opencast mining technology during the last decade. El desarrollo de la tecnologia de la mineria de superficie de la ultima decada

Energy Technology Data Exchange (ETDEWEB)

Van Leyen, H. (Rheinbraun Engineering und Wasser GmbH, Koeln (Germany). Departamento de Ingernieria Mecancia)

1992-03-01

This review only covers the development of equipment and technology and is limited to those projects involving bucket wheel excavators, including compact conveyors for use with bucket wheel excavators, main and intermediate conveyors, overburden stripping systems for continuous mining operations, cutting and trenching equipment, crushing and conveying systems for hard rock mining, aspects of excavator and dumper systems, surface winning machines, draglines and special developments in the field of materials handling and storage, blasting and other deep-mining operations. 24 refs., 19 figs., 1 tab.

25 October 2017 - Meeting on a South-East European International Institute for Sustainable Technologies

CERN Multimedia

Ordan, Julien Marius

2017-01-01

Meeting on a South-East European International Institute for Sustainable Technologies at CERN, organised by the Ministry of Science of Montenegro, followed by a lunch hosted by CERN Director-General F. Gianotti and a site visit to CMS counting room and S'Cool LAB.

Practical Education of Aerospace Field in Muroran Institute of Technology

Science.gov (United States)

Tanatsugu, Nobuhiro

Engineering study in the field of aerospace is an effective way to enhance the student motivation. The young students can be attracted by the research and development aiming at returning its results to the public society. The Muroran Institute of Technology is carrying out the practical education in the field of real research and development by the Aerospace Research Center. The projects of the center is being performed well in cooperation with the national research organization and the private companies and thereby the students have the good opportunity to find the actual situation of the real world.

Education program at the Massachusetts Institute of Technology research reactor for pre-college science teachers

International Nuclear Information System (INIS)

Hopkins, G.R.; Fecych, W.; Harling, O.K.

1989-01-01

A Pre-College Science Teacher (PCST) Seminar program has been in place at the Massachusetts Institute of Technology (MIT) Nuclear Reactor Laboratory for 4 yr. The purpose of the PCST program is to educate teachers in nuclear technology and to show teachers, and through them the community, the types of activities performed at research reactors. This paper describes the background, content, and results of the MIT PCST program

Environmental application research and future plans in plasma arc technology at the georgia institute of technology

International Nuclear Information System (INIS)

Nemeth, J.

1996-01-01

This paper summarizes the facilities and past, current, and future research efforts at the georgia institute of technology plasma Arc research facility established in 1992. This research facility was established specifically to develop and test applications related to waste management and various remediation concepts. The results of research programs in the vitrification of asbestos materials, municipal incinerator ash, and in situ testing programs, including soil remediation, waste to energy research, landfill remediation and capacity management. The presentation will also include conference and symposium announcements and invitations. 9 tabs

National Institute of Standards and Technology (NIST) cybersecurity risk management framework applied to modern vehicles

Science.gov (United States)

2014-10-01

The primary objective of the work described in this report is to review the National Institute of Science and Technology (NIST) guidelines and foundational publications from an automotive : cybersecurity risk management stand-point. The NIST approach...

Excavation of Site U14/1945, Oropi Valley, Tauranga

International Nuclear Information System (INIS)

Campbell, M.

2004-01-01

Site U14/1945 was originally recorded as two small terraces, with two probable kumara storage pits visible on the surface of the upper terrace, and shell midden visible on the surface of the lower terrace, on a low, approximately 4 m high, hill. The most unusual feature in the site, and my main purpose in writing this paper, was the oven scoop in Trench 1. This feature appeared rather unusual when excavated for a number of reasons. 6 refs., 6 figs., 1 tab

A Mobility-Aware Adaptive Duty Cycling Mechanism for Tracking Objects during Tunnel Excavation

Directory of Open Access Journals (Sweden)

Taesik Kim

2017-02-01

Full Text Available Tunnel construction workers face many dangers while working under dark conditions, with difficult access and egress, and many potential hazards. To enhance safety at tunnel construction sites, low latency tracking of mobile objects (e.g., heavy-duty equipment and construction workers is critical for managing the dangerous construction environment. Wireless Sensor Networks (WSNs are the basis for a widely used technology for monitoring the environment because of their energy-efficiency and scalability. However, their use involves an inherent point-to-point delay caused by duty cycling mechanisms that can result in a significant rise in the delivery latency for tracking mobile objects. To overcome this issue, we proposed a mobility-aware adaptive duty cycling mechanism for the WSNs based on object mobility. For the evaluation, we tested this mechanism for mobile object tracking at a tunnel excavation site. The evaluation results showed that the proposed mechanism could track mobile objects with low latency while they were moving, and could reduce energy consumption by increasing sleep time while the objects were immobile.

The radiation accident at Institute for Energy Technology Sept. 1982

International Nuclear Information System (INIS)

Berteig, L.; Flatby, J.

1983-01-01

On September 2, 1982 a radiation accident with overexposure of one person happened at the gamma irradiation plant at Institute for Energy Technology, Kjeller, Norway. This person died from the radiation injury 13 days later. In the report reference is made to the work of different groups and bodies in connection with the accident. An analysis of the causes of the accident is given. For admittance control to the irradiation area there were generally two independent door interlock systems, one irradiation source position related and the other radiation related. The latter was dismantled for repair at the time of the accident. A micro-switch failure left the source in an ushielded position, initiated a green light on the control panel and released the interlock system of the door. According to working instructions a mobile radiation monitor should have been checked for proper function and carried by anyone entering the irradiation room. This seems not to have been carried out correctly. The conditions set forth by the Norwegian Institute of Radiation Hygiene for the restarting of the irradiation plant are presented. (RF)

Regolith Advanced Surface Systems Operations Robot (RASSOR) Phase 2 and Smart Autonomous Sand-Swimming Excavator

Science.gov (United States)

Sandy, Michael

2015-01-01

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Phase 2 is an excavation robot for mining regolith on a planet like Mars. The robot is programmed using the Robotic Operating System (ROS) and it also uses a physical simulation program called Gazebo. This internship focused on various functions of the program in order to make it a more professional and efficient robot. During the internship another project called the Smart Autonomous Sand-Swimming Excavator was worked on. This is a robot that is designed to dig through sand and extract sample material. The intern worked on programming the Sand-Swimming robot, and designing the electrical system to power and control the robot.

Analysis of long-term closure in drifts excavated in Callovo-Oxfordian clay-stone: roles of anisotropy and hydro-mechanical couplings

International Nuclear Information System (INIS)

Guayacan Carrillo, Lina Maria

2016-01-01

The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian clay-stone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to principal stresses' directions. In each drift different sections have been instrumented to monitor the hydro-mechanical behavior of the rock mass formation. Continuous monitoring of the excavated zone around the drifts in the main level (-490 m) revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on the drift orientation regarding the in-situ stress field. Accordingly, the convergence measurements showed an anisotropic closure which depends also on the drifts' orientations. Moreover, marked overpressures and an anisotropic pore pressure field around the drifts have been also observed. The approach proposed in this work is mainly based on a direct analysis of the convergence measurements, for studying the anisotropic response of the rock formation during and after excavation. The convergence evolution is analyzed on the basis of the semi-empirical law proposed by Sulem et al. (1987) [Int J Rock Mech Min Sci Geomech Abstr 24: 145-154]. The monitoring and analysis of convergence data can provide a reliable approach of the interaction between rock mass and support. Therefore, the anisotropy and the variability of the closure are analyzed taking into account different field cases: drifts excavated in two different orientations (i.e. influence of the initial stress state), different methods, sizes and rates of excavation and

Interaction between groundwater and TBM (Tunnel Boring Machine) excavated tunnels

OpenAIRE

Font Capó, Jordi

2012-01-01

A number of problems, e.g. sudden inflows are encountered during tunneling under the piezometric level, especially when the excavation crosses high transmissivity areas. These inflows may drag materials when the tunnel crosses low competent layers, resulting in subsidence, chimney formation and collapses. Moreover, inflows can lead to a decrease in head level because of aquifer drainage. Tunnels can be drilled by a tunnel boring machine (TBM) to minimize inflows and groundwater impacts, restr...

EZG08 project: acoustic experiments to monitor the EDZ during the gallery excavation process in the Mont Terri Underground Research Laboratory (Switzerland)

International Nuclear Information System (INIS)

Le Gonidec, Y.; Kergosien, B.; Schubnel, A.; Gueguen, Y.; Wassermann, J.; Gibert, D.; Sarout, J.; Nussbaum, C.

2010-01-01

Document available in extended abstract form only. In the Underground Research Laboratory (URL) at Mont Terri, a new gallery G08 was planned to be excavated in 2008 following an original process: the excavation process allowed to monitor the Excavation Damaged Zone (EDZ) from geophysical measurements designed and installed at the end of face of the EZ-G04 gallery during the excavation from the other side, i.e. the end face of the EZ-G08 gallery. The objectives of the project concern spatio-temporal changes of the EDZ: among the methodological developments adapted for the EZG08 project to provide complementary information, acoustic experiments have been prepared in horizontal boreholes to perform the continuous acoustic monitoring of the Excavation Damaged Zone (EDZ). The acoustic measurements, performed on acoustic arrays of several receivers, have been recorded during one month, following two main steps: - Active acoustic surveys: a source is introduced in a central borehole (BEZG5) allowing tomography experiments in the far field and in the near field, i.e. close to and far from BEZG5, respectively. - Acoustic emissions: during the excavation process, numerous acoustic emissions can be detected and associated to micro-seismic events due to rapid crack propagation, generated by the rock relaxation, or simply associated to the excavation process. From the tomography measurements, the acoustic wave velocity field can be estimated, with P and S-wave velocities roughly equal to 2500 m/s-3500 m/s, and 1500 m/s, respectively. The acoustic setup does not show variations of P-wave velocity during the campaign, but spatial variations which could be associated to anisotropic elastic properties of the rock with the maximum P-wave velocities close to the bedding plane. An original method based on a multifrequency approach puts in evidence a frequency dependence of the velocity, with a striking phenomena since the wave velocity decreases with increasing frequency. This effect

DIDACTIC POTENTIAL OF CLOUD TECHNOLOGIES FOR MENAGMENT OF EDUCATIONAL INSTITUTION

Directory of Open Access Journals (Sweden)

А А Заславский

2016-12-01

Full Text Available The article introduces the basic definitions and differences between Services in the cloud, cloud services, cloud applications and cloud storage data. The basic cloud types that can be used on the Internet and the LAN of educational organization (Intranet. Possibilities of use of cloud services to improve of effective management at educational organization of internal and external communications of educational organizations, as well as to ensure joint work of employees of the educational organization.A list of core competencies an employee of an educational organization, which will be developed for use in the activity of cloud services and cloud applications. We describe the positive aspects of the use of cloud services and cloud-based technologies for the management of the educational institution, identifies possible risks of using cloud technologies, presents options for the use of cloud technology over the Internet and the Intranet network. We present a list of software included with every category of cloud services described types: storage and file synchronization, storage of bookmarks and notes, time management, software applications. At the article is introduced the basic definition and classification of cloud services, offered examples of methodical use of cloud services in the management of the educational organization.

Limit values used in the European Union for managing excavated land and contaminated soils

International Nuclear Information System (INIS)

Soto Diaz, E.; Rodriguez Abad, R.

2014-01-01

In this paper, which is a summary of the minor thesis of the same title, a qualitative comparison is made between mean limit values applied in different member countries of the European Union (EU) for the proper management of excavated lands and contaminated soils. This management can be carried out as a byproduct through its reuse, recycling or previous treatment, or through its consideration as a waste and its subsequent admission to a particular type of landfill. Three types of comparisons of UE limit values are done in this paper: between those established in six member countries for the use of excavated lands as a byproduct, between those existing in 15 European countries for contaminated soils, and finally between those required in 12 EU countries for their land filling. (Author)

The Historically Black Colleges and Universities/Minority Institutions Environmental Technology Consortium annual report, 1991--1992

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-12-31

The member institutions of the Consortium continue to play a significant role in increasing the number of African Americans who enter the environmental professions through the implementation of the Consortium`s RETT Plan for Research, Education, and Technology Transfer. The four major program areas identified in the RETT Plan are as follows: (1) minority outreach and precollege education; (2) undergraduate education and postsecondary training; (3) graduate and postgraduate education and research; and (4) technology transfer.

Assessment on the mechanical stability of underground excavations

International Nuclear Information System (INIS)

Kuroki, Shigemori; Taniguchi, Wataru; Sugino, Hiroyuki; Koo, Shigeru; Hasegawa, Hiroshi; Kubota, Shigeru; Dewa, Katsuyuki

1999-11-01

It is planned to construct the tunnels and emplace waste packages at several hundred meters to 1,000 meters under the ground for the repository of high-level radioactive waste based on a policy to assure the safe life environment. It is required to be mechanically stable for the tunnels to assure the work safety throughout the construction, operation and closure phase. In this report, the mechanical stability of tunnels, that is a factor of design requisites, was evaluated by the analyses to present an outline of the technical reliability of geological disposal. To put it concretely, the tunnel sections were determined to have the required areas and shapes, and the analyses on the mechanical stability at tunnel excavations and earthquake, at tunnel intersections were conducted by the theoretical analysis and finite element method. The results obtained by these investigations are shown below: It will be able to construct the tunnels with present techniques. The mechanical stability of tunnels will be assured if proper supports are given, and adequate tunnel spacing and disposal-pit pitches are set. The mechanical stability will be assured at the tunnel intersections if proper reinforcement measures are taken. The reinforcement will be required for the intersection areas over the distance of 1D (D: diameter of tunnels) on the obtuse angle side, and 4D on the acute angle side, when intersection angle is set at 30 degrees. The investigations were conducted on the assumption that the experienced big earthquake occurred. The results show that the effect of earthquake on the mechanical stability of tunnels is small, and tunnels are stable at the earthquake when the mechanical stability at tunnel excavations is assured. (author)

University of Otago 1998 field school excavations at Shag Point, North Otago

International Nuclear Information System (INIS)

Weisler, M.I.

1998-01-01

During late 1997, discussions with Gerard O'Regan, representing Te Runanga O Moeraki, lead to combining the needs of cultural resource management, teaching and research at the Shag Point archaeological site, situated about an hour's drive north from the University of Otago. In late 1996, a car park (ca. 20 by 40 m) was bulldozed on Department of Conservation land just inland from Shag Point. Unfortunately, the north-east portion of the site, as well as cultural deposits along newly graded access roads, were destroyed. Te Runanga O Moeraki requested that I conduct archaeological survey and excavations at Shag Point to determine the extent of site destruction and to recover a sample of cultural material in the bulldozer spoil dirt. In addition to these cultural resource management objectives, it was necessary, from a research point of view, to determine: (1) the site area; (2) dates of site use; (3) the nature of occupation, subsistence practices and stone-tool technology; (4) evidence of interaction through analysis of imported artefacts; and (5) relationship of the Shag Point site to the major prehistoric village at Shag River mouth, located less than 1 km south. (author). 2 refs., 2 figs

Investigative study of the underground excavations for a nuclear waste repository in tuff: Nevada Nuclear Waste Storage Investigations Project

International Nuclear Information System (INIS)

St John, C.M.

1987-07-01

Numerical studies were conducted on the behavior of a tuff rock mass within which emplacement drifts for a nuclear waste repository are excavated. The first study evaluated the effects of rockbolting and excavation-induced damage on the behavior of the rock mass round typical drifts. The second study provided a simple means of assessing the significance of drift shape, drift size, and in-situ state of stress on the deformation and stress in the vicinity of drifts for vertical and horizontal emplacement of waste. Neither study considered the effect of heating of the rock mass after emplacement of the waste so the conclusions pertain only to the conditions immediately after excavation of the underground openings. The results of analyses of the rockbolted excavations indicated that rockbolts do not have a significant influence on the states of deformation or stress within the rock mass, and that the rockbolts are subjected to acceptable levels of stress even if installed as close to the face of the excavation as possible. Accordingly, rockbolts were not considered in the study of drift shape, drift size, and the in-situ state of stress. That study indicated that stable openings of the dimensions investigated can be constructed within a tuff rock mass with the properties assumed. Of the parameters investigated, the in-situ state of stress appeared to be most important. Potentially adverse conditions were predicted if the in-situ horizontal stress is very low, but current indications are that it lies within a range which is consistent with good conditions and a stable roof. 28 refs., 49 figs., 11 tabs

Dynamic simulation of cable shovel specific energy in oil sands excavation

Energy Technology Data Exchange (ETDEWEB)

Awuah-Offei, K. [Missouri-Rolla Univ., Rolla, MO (United States). School of Materials, Energy and Earth Resources; Frimpong, S. [Missouri-Rolla Univ., Rolla, MO (United States). Dept. of Mining Engineering, Mining and Nuclear Engineering; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering

2005-07-01

Oil sand excavation requires the use cable shovels which constitute one of the major costs in surface mining operations. Random occurrences of shales and limestones within the Athabasca oil sands formation result in varying shovel diggability and stress loading of the boom-crowd-dipper-teeth assembly which reduces digging efficiency. This inefficient use of cable shovels negatively affects the return on capital investment in these otherwise effective machines. In the Athabasca oil sands, varying stress loading has the potential to increase shovel downtime and increase maintenance costs. This paper presented a newly developed cable shovel simulator that uses shovel kinematics and dynamics, dynamic cutting resistance and payload models. It can model the specific energy needed to overcome the resistance to machine motion and material digging. The comprehensive model considers both machine motion and machine-formation interaction forces. It also provides a comprehensive theoretical assessment of shovel performance. The model is useful to mining engineers when examining both the machine operating parameters and material parameters that influence shovel performance. The study showed that bulk density is the most important material property influencing diggability. Operator preferences also influence the specific energy of excavation. 12 refs., 2 tabs., 6 figs.

Obligatory inquiries concerning buried pipelines in case of intended excavations on private ground; Zur Erkundigungspflicht nach erdverlegten Versorgungsanlagen bei Tiefbauarbeiten auf privaten Grundstuecken

Energy Technology Data Exchange (ETDEWEB)

Schulze, O.

2006-09-15

If inquiries concerning buried pipelines in case of intended excavations on private ground are neglected, this may have dramatic consequences. As an example, at Griselenghein near Ath, Belgium, excavations damaged the gas pipeline on 30 July 2004, and 18 were killed during the subsequent explosion. The contribution outlines cases in which inquiries concerning buried pipelines in case of intended excavations on private ground are obligatory. It points out regulations that come into force in case of neglect, and the potential contributory negligence of the utility if pipelines are not buried deep enough. (orig.)

Assessment of the mechanical stability of underground excavations

International Nuclear Information System (INIS)

Kuroki, Shigemori; Taniguchi, Wataru

1999-01-01

Each tunnel in the underground high level radioactive waste repository must be mechanically stable to maintain safety throughout the construction, emplacement operations and closure phase. The mechanical stability of underground excavations were assessed using a theoretical analysis and a finite element method taking a wide range of geological environment in Japan into consideration to establish confidence in the construction of disposal facilities. The results show that it is possible to maintain the mechanical stability with adequate tunnel spacing and disposal pit pitch and proper mechanical support. The procedure used for the analysis of the mechanical stability in the H12 report and the results are described in this report. (author)

Aspects to improve cabin comfort of wheel loaders and excavators according to operators

NARCIS (Netherlands)

Kuijt-Evers, L.F.M.; Krause, F.; Vink, P.

2003-01-01

Comfort plays an increasingly important role in interior design of earth moving equipment. Although research has been conducted on vehicle interiors of wheel loaders and excavators, hardly any information is known about the operator's opinion. In this study a questionnaire was completed by machine

Design aspects of the Alpha Repository. V. Suite selection and cost analysis of excavation/hauling systems

International Nuclear Information System (INIS)

Zeller, T.J.; Grams, W.H.

1975-01-01

The various types of haulage and excavation equipment that may be suitable for use in the development and excavation of the Alpha repository are described with discussion of the advantages, disadvantages, expected costs, availability, and special features of each. The various equipment suites are delineated, and the costs of mining and transportation of the salt are presented and discussed. Individual manufacturers contacted and equipment considered are listed. Most of the equipment is ''off-the-shelf''; however, some manufactuers were contacted that do custom work because of their expertise in salt mining equipment. The costs of custom equipment are comparable to those for standard equipment

Institutions and Technological Learning: Public-Private Linkages in Agricultural Research in Brazil and Argentina

Directory of Open Access Journals (Sweden)

Marcos Paulo Fuck

2009-07-01

Full Text Available The article discusses the institutional arrangements and forms of organization of agricultural research in Brazil and Argentina. The analysis focuses on Embrapa in the Brazilian case and INTA in the Argentinian case. Emphasis is laid on the two institutions’ policies regarding intellectual property and technology transfer. The aim is to contribute to the debate about how to conceptualize the co-evolution of organizations considering the technical, scientific, legal, regulatory, economic and other contexts in which they operate, reinforcing the idea of learning and that economic institutions do not just evolve but co-evolve.

Characterization and functional correlation of multiple imaging modalities with focal choroidal excavation

Directory of Open Access Journals (Sweden)

Yun-Chen Chen

2018-05-01

Full Text Available Background: To investigate the clinical manifestations and imaging features of near-infrared autofluorescence (NIA, infrared reflectance (IR, fundus autofluorescence (FAF, indocyanine green angiography (ICGA and fluorescein angiography (FAG in the detection of patients with focal choroidal excavation (FCE identified by cross-sectional spectral-domain optical coherence tomography (SD-OCT. Methods: This retrospective cross-sectional study included 12 eyes of 10 Taiwanese patients with FCE diagnosed by SD-OCT. The areas and depths of FCE in serial cross-sectional and en-face OCT were compared in different imaging modalities. NIA, IR, FAF, ICGA and FAG images were obtained. Best corrected visual acuity, subjective distortion area in the Amsler grid and history of maculopathies were also recorded. Results: In areas where the choroid started to excavate as shown in SD-OCT, hypo-autofluorescence in NIA was noted. The area of hypo-fluorescence in NIA of all the FCE lesions showed good correlation with the size. The area of FCE was associated with complications such as choroidal neovascularization and central serous chorioretinopathy (p = 0.014, d.f = 1 and the volume (NIA area × Depth measured by SD-OCT × 1/3 was associated with subjective distortion strongly (p = 0.051, Spearman's correlation = 0.600. Conclusion: Among all image modalities, NIA was the most sensitive tool in area measurement of FCE and peripheral lesion detection. Also, the volume of FCE was associated with subjective distortion and the area was related to complications. Recording the area and volume of FCE could play an important role in monitoring complications. Keywords: Choroid-retina disease, Focal choroidal excavation, Near-infrared autofluorescence, Spectral-domain optical coherence tomography

Design of Intelligent Hydraulic Excavator Control System Based on PID Method

Science.gov (United States)

Zhang, Jun; Jiao, Shengjie; Liao, Xiaoming; Yin, Penglong; Wang, Yulin; Si, Kuimao; Zhang, Yi; Gu, Hairong

Most of the domestic designed hydraulic excavators adopt the constant power design method and set 85%~90% of engine power as the hydraulic system adoption power, it causes high energy loss due to mismatching of power between the engine and the pump. While the variation of the rotational speed of engine could sense the power shift of the load, it provides a new method to adjust the power matching between engine and pump through engine speed. Based on negative flux hydraulic system, an intelligent hydraulic excavator control system was designed based on rotational speed sensing method to improve energy efficiency. The control system was consisted of engine control module, pump power adjusted module, engine idle module and system fault diagnosis module. Special PLC with CAN bus was used to acquired the sensors and adjusts the pump absorption power according to load variation. Four energy saving control strategies with constant power method were employed to improve the fuel utilization. Three power modes (H, S and L mode) were designed to meet different working status; Auto idle function was employed to save energy through two work status detected pressure switches, 1300rpm was setting as the idle speed according to the engine consumption fuel curve. Transient overload function was designed for deep digging within short time without spending extra fuel. An increasing PID method was employed to realize power matching between engine and pump, the rotational speed's variation was taken as the PID algorithm's input; the current of proportional valve of variable displacement pump was the PID's output. The result indicated that the auto idle could decrease fuel consumption by 33.33% compared to work in maximum speed of H mode, the PID control method could take full use of maximum engine power at each power mode and keep the engine speed at stable range. Application of rotational speed sensing method provides a reliable method to improve the excavator's energy efficiency and

Fish Remains from Excavations near the Riverfront at Newcastle upon Tyne, England

Directory of Open Access Journals (Sweden)

Rebecca A. Nicholson

1997-12-01

Full Text Available The City of Newcastle, situated some 10 miles inland on the River Tyne in north-east England, is not now an important fishing port. Most of the fresh fish marketed in the city has been landed at the nearby coastal ports of North and South Shields. Excavations at two sites behind the present Quayside in Newcastle, however, have yielded quantities of fish bones, representing a wide variety of species. This is in contrast to excavations in other parts of the city, where few fish remains have been recovered, and suggests that the quayside in Newcastle was an important centre for the fishing industry during the medieval period. It seems likely that most of the fish remains represent waste from landing and processing fish on or near the quayside. Yet, when taphonomic factors are taken into account, the limitations of using even large bone assemblages to interpret processing activities is demonstrated. As always, the need for a programme of on-site sieving to obtain representative samples of fish bone is evident.

Backfilling techniques and materials in underground excavations: Potential alternative backfill materials in use in Posiva's spent fuel repository concept

International Nuclear Information System (INIS)

Dixon, D.A.; Keto, P.

2009-05-01

A variety of geologic media options have been proposed as being suitable for safely and permanently disposing of spent nuclear fuel or fuel reprocessing wastes. In Finland the concept selected is construction of a deep repository in crystalline rock (Posiva 1999, 2006; SKB 1999), likely at the Olkiluoto site (Posiva 2006). Should that site prove suitable, excavation of tunnels and several vertical shafts will be necessary. These excavations will need to be backfilled and sealed as emplacement operations are completed and eventually all of the openings will need to be backfilled and sealed. Clay-based materials were selected after extensive review of materials options and the potential for practical implementation in a repository and work over a 30+ year period has led to the development of a number of workable clay-based backfilling options, although discussion persists as to the most suitable clay materials and placement technologies to use. As part of the continuous process of re-evaluating backfilling options in order to provide the best options possible, placement methods and materials that have been given less attention have been revisited. Primary among options that were and continue to be evaluated as a potential backfill are cementitious materials. These materials were included in the list of candidate materials initially screened in the late 1970's for use in repository backfilling. Conventional cement-based materials were quickly identified as having some serious technical limitations with respect their ability to fulfil the identified requirements of backfill. Concerns related to their ability to achieve the performance criteria defined for backfill resulted in their exclusion from large-scale use as backfill in a repository. Development of new, less chemically aggressive cementitious materials and installation technologies has resulted in their re-evaluation. Concrete and cementitious materials have and are being developed that have chemical, durability

E16 Sandvika-Wøyen - Analysis of tunnel excavation, achieved contour quality and influence of applied initiation system.

OpenAIRE

Sklodowska, Anna Maria

2016-01-01

The drill and blast excavation method is the most commonly used method for tunnel construction in Norway. In D&B the results from blasting can be evaluated through several factors, such as pull percentage, vibration level and contour quality. The main goal of the thesis was to analyze excavation with a special focus on the quality of the achieved contour and the influence of the applied initiation system. The analysis was performed based on results from the Bjørnegård tunnel, which wa...

The Li(f)e of the Self: Missing Persons and Auto/Archeological Excavations

Science.gov (United States)

Burdick, Jake

2014-01-01

This article describes and enacts a process of autobiographical inquiry, auto/archeology, which seeks to address problematic confluences of memory and identity in reconstructing one's historical narrative. Drawing on curriculum theory and Lacanian psychoanalysis, the author describes a process of excavation in which understandings of a prior…

Making Learning and Web 2.0 Technologies Work for Higher Learning Institutions in Africa

Science.gov (United States)

Lwoga, Edda

2012-01-01

Purpose: This paper seeks to assess the extent to which learning and Web 2.0 technologies are utilised to support learning and teaching in Africa's higher learning institutions, with a specific focus on Tanzania's public universities. Design/methodology/approach: A combination of content analysis and semi-structured interviews was used to collect…

Coupled hydrological-mechanical effects due to excavation of underground openings in unsaturated fractured rocks

International Nuclear Information System (INIS)

Montazer, P.

1985-01-01

One of the effects of excavating an underground opening in fractured rocks is a modification of the state of the stress in the rock mass in the vicinity of the opening. This effect causes changes in the geometry of the cross sections of the fracture planes, which in turn results in modification of the hydrologic properties of the fractures of the rock mass. The significance of the orientation of the fractures and their stiffness on the extent of the modification of the hydrologic properties as a result of excavation of underground openings is demonstrated. A conceptual model is presented to illustrate the complexity of the coupled hydrological-mechanical phenomena in the unsaturated zone. This conceptual model is used to develop an investigative program to assess the extent of the effect at a proposed repository site for storing high-level nuclear wastes

The Historically Black Colleges and Universities/Minority Institutions Environmental Technology and Waste Management Consortium annual report, 1990--1991

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-12-31

The HBCU/MI Environmental Technology and Waste Management Consortium was established in January 1990, through a Memorandum of Understanding (MOU) among the member institutions. This group of research-oriented Historically Black Colleges and Universities and Minority Institutions (HBCU/MI) agreed to work together to initiate research, technology development and education programs to address the nation`s critical environmental problems. As a group the HBCU/MI Consortium is uniquely positioned to reach women and the minority populations of African Americans, Hispanics and American Indians. As part of their initial work, they developed the Research, Education, and Technology Transfer (RETT) Plan to actualize the Consortium`s guiding principles. In addition to developing a comprehensive research agenda, four major programs were begun to meet these goals. This report summarizes the 1990--1991 progress.

THE IMPACT OF NEW INFORMATION AND COMMUNICATION TECHNOLOGIES IN PUBLIC INSTITUTIONS ACCOUNTING

Directory of Open Access Journals (Sweden)

Valentin Ioan UŞURELU

2010-12-01

Full Text Available The studied field has suffered continuous transformation, both in interaction with other scientific fields and in constituent sub-classes, for discovering and understanding more deeply the contemporary economic realities under the impact of major trends of world development. This paper aims to analyze the location and the effects of information and communication technologies within the public accounting in order to evaluate the effects of this element on accounting research, teaching and professional practice. In a comprehensive approach of public institutions accounting, new information and communication technologies represent a tool that facilitates the accounting function and realizes the connection between the transmitter and the receiver, both within and outside the organization, not just at the micro and macro economic level but also at the micro and macro social one. The advantages of recent progress of information and communication technologies are obvious for the organizations management. It highlights the developments and challenges represented by these new technologies for researchers and professionals in the idea of performing a broad and flexible view of public accounting enabling them to provide useful services for all categories of users of accounting information.

The Design and Development of Educational Materials Using Microcomputer Technology in Distance Teaching Institutions: Some Issues for Consideration.

Science.gov (United States)

Yates, Christopher

Perhaps the most significant development in microcomputer technology over the last two years has been the development of desktop publishing techniques. This technology promises to offer some significant advantages to institutions developing instructional materials in less developed countries, particularly in terms of control, cost effectiveness,…

118-B-1 excavation treatability test procedures

International Nuclear Information System (INIS)

Frain, J.M.

1994-01-01

This treatability study has two purposes: to support development of the approach to be used for burial ground remediation, and to provide specific engineering information for the design of burial grounds receiving waste generated from the 100 Area removal actions. Data generated from this test will also provide performance and cost information necessary for detailed analysis of alternatives for burial ground remediation. Further details on the test requirements, milestones and data quality objectives are described in detail in the 118-B-1 Excavation Treatability Test Plan (DOE/RL-94-43). These working procedures are intended for use by field personnel to implement the requirements of the milestone. A copy of the detailed Test Plan will be kept on file at the on-site field support trailer, and will be available for review by field personnel

Pre-excavation studies of prehistoric cave sites by magnetic prospecting

Science.gov (United States)

Itkis., Sonia; Matskevich, Zinovii; Meshveliani, Tengiz

2014-05-01

Detailed magnetic survey was performed for caves study in Israel (1995-1996) within the framework of the Beit Shemesh Regional Project (Judean Shephelah). The experience accumulated in Israel we applied later (2010) in two Georgian prehistoric cave sites: Cherula and Kotias-Klde. The magnetic method is based on the contrast in magnetic properties between a target object (e.g., buried archaeological feature) and the host medium (i.e, the surrounding bedrock and soil). The feasibility of the magnetic method for cave revealing was evaluated by magnetic susceptibility (κ) measurements of surrounding soil and rocks, and archaeological features: stones making up the walls, ceramic fragments and cave fill. According to data obtained, the κ of soil within caves (cave fill) is higher than that of surrounding soil. The enhancement of cave fill κ occurs because processes associated with human habitation: repeated heating and accumulation of organic debris. Both these processes provide good conditions for the conversion of the iron oxide found within the soil to a strongly ferromagnetic form (Mullins, 1977; Maher, 1986; Dalan and Banerjee, 1998, Itkis and Eppelbaum, 1999; Itkis, 2003) The presence of highly magnetic ceramics in caves also enhances magnetic contrast between practically non-magnetic bed rock (chalk in Ramat Beit Shemesh Site (Israel) and limestone (Georgian sites) and the cave fill, increasing the potential of the magnetic method to reveal caves (Itkis, 2011). Based on magnetic survey results, an excavation revealed a cave with a large amount of well preserved pottery and finds typical of the Early Bronze Age. Both studied cave sites in Georgia were located in Chiatura region of Imeretia province. Cherula site is a karstic rockshelter with a single chamber, ca 100 sq. m. The site was briefly tested in 1970s'. The area excavated in 2010 went to the depth of 60 cm below the present day surface; the limestone bedrock was not reached. The excavation revealed

Simulating the time-dependent behaviour of excavations in hard rock

CSIR Research Space (South Africa)

Malan, DF

2002-10-01

Full Text Available (1993) estimated the rock disintegration of the roof of the Swedish repository at Forsmark where the excavation is intersected by a fracture zone. By generalising the structure to be one of regular layers of blocks and applying a log- time creep law, he... and secondary closure in squeezing tunnels. Tertiary movements can be considered by providing suitable laws relating the values of the mechanical parameters (such as viscosity) to the irreversible part of the time-dependent strain. These rheological models...

75 FR 62892 - Massachusetts Institute of Technology Research Reactor Environmental Assessment and Finding of No...

Science.gov (United States)

2010-10-13

... NUCLEAR REGULATORY COMMISSION [Docket No. 50-020; NRC-2010-0313] Massachusetts Institute of Technology Research Reactor Environmental Assessment and Finding of No Significant Impact Correction In notice document 2010-24809 beginning on page 61220 in the issue of Monday, October 4, 2010, make the...

Comparison of visual observation and excavation to quantify density of the endangered bivalve Unio crassus in rivers of north-eastern France

Directory of Open Access Journals (Sweden)

Lamand F.

2014-04-01

Full Text Available In the context of a rapid decline in several protected unionid species, government agencies urgently require a reliable method to estimate population size for the most endangered species. We used a dataset collected from 16 river stations in north-eastern France to compare the efficiency of visual estimation (bathyscope and a manual excavation to estimate numbers of the endangered bivalve Unio crassus. Our investigations indicated that, whereas a visual approach was sufficient to detect unionid presence, only 10% of all individuals were registered compared with manual excavation at the same site. In order to obtain an accurate density estimate (especially as regards the juvenile population, sediment excavation is necessary, despite it being time consuming and damaging to the mussel’s habitat.

Nanotechnology Laboratory Continues Partnership with FDA and National Institute of Standards and Technology | Poster

Science.gov (United States)

The NCI-funded Nanotechnology Characterization Laboratory (NCL)—a leader in evaluating promising nanomedicines to fight cancer—recently renewed its collaboration with the U.S. Food and Drug Administration (FDA) and the National Institute of Standards and Technology (NIST) to continue its groundbreaking work on characterizing nanomedicines and moving them toward the clinic. In

Activities of the data centers on atomic spectroscopy at the National Institute of Standards and Technology

International Nuclear Information System (INIS)

Wiese, W.L.

1990-01-01

The activities concerning Atomic Energy Levels and Wavelengths, Atomic Transition Probabilities and Spectral Line Shapes and Shifts at the National Institute of Standards and Technology (Gaithersburg, USA) are listed together with the corresponding lists of publications

Research and development on activation analysis at the Thailand Institute of Nuclear Technology

International Nuclear Information System (INIS)

Laoharojanaphand, S.; Dharmavanij, W.; Busamongkol, A.; Pareepart, R.; Wimolwattanapun, W.; Chantarachot, W.

2008-01-01

Research and development in activation analysis at the Thailand Institute of Nuclear Technology has been carried out over 40 years. The main activation source is from the TRIGA type research reactor TRR1/M1. Average in-core flux is around 10 13 n x cm -2 x s -1 . Experience on the analysis of various kind of samples range from environmental field especially air particulate, ores, rocks and soil for natural resources exploration as well as industrial applications. Elemental composition in silk thread, silk cocoon and silk products from the royal silk project are one of the research work done incorporation with the Queen Sirikit Institute of Sericulture. Food items are also another topic of interest to our research team. (author)

Activities of Nuclear Research Institute Rez in the area of hydrogen technologies

International Nuclear Information System (INIS)

Doucek, A.; Janik, L.; Misak, J.

2010-01-01

NRI is a research institution established in 1955. Nowadays, the Institute provides wide range of expertise and services for operators of the nuclear power plants in the Czech Republic and abroad, supports Czech central state institutions in the domains of strategic energy planning and development, management of radioactive waste (for the Ministry of Trade and Industry), provides independent expertise for the State Office of Nuclear Safety, performs activities in the area of exploitation of ionising radiation and irradiation services for basic and applied research, health service and industry, performs research and provides services for radioactive waste disposal, production of radiopharmaceuticals, education and training of experts and scientific specialists and performs many other activities. With the gradual changes in energy policy, hydrogen economy becomes one of the important topics related to nuclear energy. NRI is participating in the research and development in this area and as a member of the Czech Hydrogen Technology Platform is currently the leader in this area in the country. To promote hydrogen economy, NRI prepared and participated in several demonstration projects. Studies on production of hydrogen in current and future nuclear power plants are performed as well. (authors)

A new bee species that excavates sandstone nests.

Science.gov (United States)

Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

2016-09-12

Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Stepwise excavation may enhance pulp preservation in permanent teeth affected by dental caries

DEFF Research Database (Denmark)

Bjørndal, Lars

2011-01-01

ARTICLE TITLE AND BIBLIOGRAPHIC INFORMATION: Ways of enhancing pulp preservation by stepwise excavation-a systematic review. Hayashi M, Fujitani M, Yamaki C, Momoi Y. J Dent 2011;39(2):95-107. Epub 2010 Dec 3. REVIEWER: Lars Bjørndal, DDS, PhD, Dr Odont PURPOSE/QUESTION: To determine the clinical...

Environmental and institutional considerations in the development and implementation of biomass energy technologies

Energy Technology Data Exchange (ETDEWEB)

Schwab, C.

1979-09-01

The photosynthetic energy stored in plant and organic waste materials in the United States amounts to approximately 40% of the nation's total energy consumption. Conversion of this energy to usable power sources is a complex process, involving many possible materials, conversion technologies, and energy products. Near-term biomass technologies are predominantly based on traditional fuel use and have the advantage over other solar technologies of fitting into existing tax and business practices. However, no other solar technology has the potential for such large environmental impacts. Unlike the conversion of sun, wind, and ocean thermal energy, the conversion of the biomass energy source, in the form of biomass residues and wastes, can create problems. Environmental impacts may be significant, and legal responses to these impacts are a key determinant to the widespread adoption of biomass technologies. This paper focuses on the major legal areas which will impact on biomass energy conversion. These include (1) the effect of existing state and federal legislation, (2) the role of regulatory agencies in the development of biomass energy, (3) governmental incentives to biomass development, and (4) legal issues surrounding the functioning of the technologies themselves. Emphasis is placed on the near-term technologies whose environmental impacts and institutional limitations are more readily identified. If biomass energy is to begin to achieve its apparently great potential, these questions must receive immediate attention.

Radiocarbon dating of a sutra container excavated at the Minagi Daibutsuyama site, Fukuoka Prefecture, Japan

International Nuclear Information System (INIS)

Oda, Hirotaka; Nakamura, Toshio; Tsukamoto, Toshio